Professional Documents
Culture Documents
www.huawei.com
Contents
GENEX Overview GENEX Probe General Workflow Using Probe for Data Collection Other Features Case Study
www.huawei.com
The GENEX Probe, network optimization and drive test data collection system, is an air interface test tool for WCDMA/HSDPA/HSUPA/GSM/GP RS networks. GENEX Assistant is a professional wireless test data post-processing software system.
RNC
GENEX U-Net is a radio planning tool that fully supports the technologies of GSM,GPRS-EDGE, CDMA IS95, WCDMA/UMTS/HSDPA/HSUPA, CDMA 2000/1xRTT/1xEVDO, and TD-SCDMA wireless networks.
www.huawei.com
Air Interface Test Tool and Post-Processing Tool Network Performance Analysis Tool
www.huawei.com
www.huawei.com
Contents
GENEX Overview GENEX Probe General Workflow Using Probe for HSDPA / HSUPA DT Data Collection Other Features Case Study
www.huawei.com
AT Command Huawei WCDMA/HSDPA Data card Supported Qualcomm TM6250/ Mobile 6275
Anritsu Scanner
Equipment Composition
support multi UE carry out different tests simultaneously
Physical connection
Equipment bag easy to carry and suitable to be used in the car
www.huawei.com
Contents
GENEX Overview GENEX Probe General Workflow Using Probe for Data Collection Other Features Case Study
www.huawei.com
DT Operation Flow
1. Probe Installation. 2. Plug Probe dongle. (Must be installed Shared Hardware key) 3. Connect Hardware device to the laptop. 4. Hardware device configuration. 5. System Configuration. (Set Log mask) 6. Test Plan Configuration. 7. Open the parameter widows you want to observe, such as RSCP and Ec/Io in Active Set, Monitor Set; HSDPA Serving Cell, throughput; RRC Message, NAS Message, etc. 8. Import engineering parameters, open Map window and import the related Mapinfo file (.TAB). (Routes, Streets, etc) 9. Start Test, start recording. 10. After the test finished, press "Stop Test button.
Notes: If you don't use "Test Plan" to start test automatically, please "Start Test first, then start to make call test. www.huawei.com
Huawei confidential, 2007-10
Probe Interface
Status Area
10
www.huawei.com
10
Probe Interface
Navigation View
11
www.huawei.com
11
Project Template
Project Template
Site Verification Optimize Benchmark Acceptance Customize
12
www.huawei.com
12
!!
13
www.huawei.com
13
!!
Hardware Test
14
www.huawei.com
14
15
www.huawei.com
15
Scanner1 Scanner
DTI WCDMA 115200 (869.0-894.0 MHz) HUAWEI U1205 HUAWEI U1205 HUAWEI E270 Card*** 230400 230400 230400
UE UE UE
16
www.huawei.com
16
17
www.huawei.com
17
DT Operation Flow
1. 2. 3. 4. 5. 6. 7. Probe Installation. Plug Probe dongle. (Must be installed Shared Hardware key) Connect Hardware device to the laptop. Hardware device configuration. System Configuration. (Set Log mask) Test Plan Configuration. Open the parameter widows you want to observe, such as RSCP and Ec/Io in Active Set, Monitor Set; HSDPA Serving Cell, throughput; RRC Message, NAS Message, etc. 8. Import engineering parameters, open Map window and import the related Mapinfo file (.TAB). (Routes, Streets, etc) 9. Start Test, start recording. 10. After the test finished, press "Stop Test button.
Notes: If you don't use "Test Plan" to start test automatically, please "Start Test first, then start to make call test. www.huawei.com
Huawei confidential, 2007-10
18
18
Set Log Name Set Log file size Location of saved logs
19
www.huawei.com
19
20
www.huawei.com
20
21
www.huawei.com
21
22
www.huawei.com
22
23
www.huawei.com
23
24
www.huawei.com
24
DT Operation Flow
1. 2. 3. 4. 5. 6. 7. Probe Installation. Plug Probe dongle. (Must be installed Shared Hardware key) Connect Hardware device to the laptop. Hardware device configuration. System Configuration. (Set Log mask) Test Plan Configuration. Open the parameter widows you want to observe, such as RSCP and Ec/Io in Active Set, Monitor Set; HSDPA Serving Cell, throughput; RRC Message, NAS Message, etc. 8. Import engineering parameters, open Map window and import the related Mapinfo file (.TAB). (Routes, Streets, etc) 9. Start Test, start recording. 10. After the test finished, press "Stop Test button.
Notes: If you don't use "Test Plan" to start test automatically, please "Start Test first, then start to make call test. www.huawei.com
Huawei confidential, 2007-10
25
25
26
www.huawei.com
26
27
www.huawei.com
27
!!
28
www.huawei.com
28
!!
29
www.huawei.com
29
Suggestion: When testing voice call, do not perform PS dialup on the Modem of the outgoing UE manually. Otherwise, voice call maybe hangs up abnormally. The UE that is performing PS services can serve as an incoming UE for Voice Call or Video Phone test. Thus, the CS and PS concurrent test can be performed on the same UE.
30
www.huawei.com
30
Setup time:
the maximum time for call setup. If the call cannot be setup within the defined period, the call setup fails. the duration of one call, from call setup to call normal release. (apply only to call by call) the time between two calls, from the previous call disconnection to the beginning of the next call.
The interval between the exceptional end of a call drop
and the beginning of the next call. the limitations on the call number -> Finite / Infinite.
31
www.huawei.com
31
Note: PS connection can be set up by one FTP Download test item if correct APN has been set in UE.
32
32
www.huawei.com
MultiTask Count:
The time interval between multi downloads. After finishing a download, wait for several time, then start another download test. the total number of ftp download test.
33
www.huawei.com
33
Disconnect By Time: Perform PDP context deactivation periodically. The period for
the PDP context deactivation is represented by the Valid FTP Duration parameter. If the target files are not loaded completely within the predefined time, the loading result shows timeout. Probe considers this loading as failure and initiates another PDP context deactivation in the next loading.
Disconnect After Transfer Complete: Each time when the file load is
complete, PDP context deactivation would be performed.
FTP QoS : Indicates the type of the traffic as: Background class
Conversational class Interactive class Streaming class Subscribed class
FTP Upload:
34
www.huawei.com
Parameters are the same with FTP downloads. Probe will upload the local file to the destination path automatically. **Make sure you have the authority to upload file before test.
Huawei confidential, 2007-10
34
!!
When both Probe and MODEM have APN and QoS information, because AT command in MODEM initial command is send to UE more closely before PS connection setup, it will replace the information send to UE by Probe. That is Probes setting doesnt work if AT command also exists in the MODEM initial command.
35
www.huawei.com
35
36
www.huawei.com
36
37
www.huawei.com
37
38
www.huawei.com
38
39
www.huawei.com
39
Password: A definir Remote File: A definir Write Local File: MultiTask Count: 5 Test Interval(sec): Ftp Count: Traffic Class: UL Max Rate(Kbps): DL Max Rate(Kbps): 40 5 999 False
40
www.huawei.com
Measure Aggregate Ec/Io: Measure Delay Spread: FALSE Measure Eps/Io: Measure Ess/Io: FALSE FALSE
41
www.huawei.com
41
DT Operation Flow
1. 2. 3. 4. 5. 6. 7. Probe Installation. Plug Probe dongle. (Must be installed Shared Hardware key) Connect Hardware device to the laptop. Hardware device configuration. System Configuration. (Set Log mask) Test Plan Configuration. Open the parameter widows you want to observe, such as RSCP and Ec/Io in Active Set, Monitor Set; HSDPA Serving Cell, throughput; RRC Message, NAS Message, etc. 8. Import engineering parameters, open Map window and import the related Mapinfo file (.TAB). (Routes, Streets, etc) 9. Start Test, start recording. 10. After the test finished, press "Stop Test button.
Notes: If you don't use "Test Plan" to start test automatically, please "Start Test first, then start to make call test. www.huawei.com
Huawei confidential, 2007-10
42
42
Parameter Window
Common used windows for HSDPA & R99
43
www.huawei.com
43
Parameter Window
WCDMA - Serving, Active Set & Neighboring Cells
Display PSC, RSCP, Ec/Io for active set, monitor set and detective set In the figure, rectangle legend implicates active set data, circle implicates monitor set data, and triangle implicates detected set data. The data of the same type is distinguished from each other with different colors. Move the mouse to a place to get the scrambling code of the current point. When the UE is in idle state, PSC in active set is about the cell where the UE resides.
www.huawei.com
Huawei confidential, 2007-10
44
44
Parameter Window
WCDMA - Power Control
DL SIR, SIR Target
45
www.huawei.com
45
Parameter Window
WCDMA - WCDMA BLER
Displays BLER of different transport channels. In HSDPA connection mode, A-DPCH's DL BLER is being displayed.
46
www.huawei.com
46
Parameter Window
WCDMA - HSDPA Link Statistic
47
www.huawei.com
47
Parameter Window
Message - MAC/RLC Messages
The MAC/RLC Messages window displays the messages about Media Access Control (MAC) and Radio Link Control (RLC). The messages are visible only when the associated items in LogMask are selected.
48
www.huawei.com
48
Parameter Window
Message - RRC Messages
All the UEs or single UE are displayed on the window. The messages selected on the left navigation tree are displayed. The detailed information is displayed by double-clicking on the message.
49
www.huawei.com
49
Parameter Window
Message - NAS Messages
Whatever mode UE is in, WCDMA, HSDPA or GSM, all the NAS messages are displayed here as follow:
50
www.huawei.com
50
Parameter Window
Scanner TopN Pilot & Spectrum Analysis
51
www.huawei.com
51
Parameter Window
Data Service - App Throughput
Display both UL and DL application layer data rate, NAS rate and TCP retransmission rate.
52
www.huawei.com
52
Parameter Window
Data Service - RLC Throughput
Display both UL and DL RLC layer throughput, UL PDU retransmission ratio and DL PDU error ratio.
53
www.huawei.com
53
Parameter Window
Data Service - FTP Service Quality Evaluation
Displays the associated indicators on the user plane of the FTP service, including Login time, download time, download rate, etc.
54
www.huawei.com
54
Parameter Window
UE State
Displays the information of the mobile status and network parameters (cell, rnc, MCC, MNC, LAC, RAC)
55
www.huawei.com
55
Parameter Window
Information
Displays the information of hardware used and the test plan running
56
www.huawei.com
56
Parameter Window
Map Window
57
www.huawei.com
57
Parameter Window
Map Window Load WCDMA sites
58
www.huawei.com
58
59
www.huawei.com
59
Contents
Case1. Inter-RAT handover test Case2. WCDMA inter-frequency handover test Case3. Multi-frequency Scanning
60
www.huawei.com
60
61
www.huawei.com
61
62
www.huawei.com
62
The signal frequency in active set is 2137.40 when the test starts
Signaling window
Log file:
63
63
www.huawei.com
64
www.huawei.com
64
65
65
1. Set multi-frequency
66
www.huawei.com
67
www.huawei.com
67
www.huawei.com