You are on page 1of 100

According to principle of conservation of energy, the total momentum of a system of masses in any direction remains constant unless acted

upon by an external force in that direction A. True B. False

A. True

B. False

The friction experienced by a body, when in motion , is known as A, rolling friction B, dynamic friction C, limiting friction D, static friction

A, rolling friction B, dynamic friction C, limiting friction D, static friction

The term force may be defined as an agent which produces or tends to produce, destroys or tends to destroy motion. A. Agree B. Disagree

A. Agree B. Disagree

The coefficient of restitution for elastic bodies is one A. Correct B. Incorrect

A. Correct B. Incorrect

The angle of inclination of a vehicle when moving along a circular path_____upon its mass A. depends B. does not depends

A. depends B. does not depends

The point, through which the whole weight of the body acts, irrespective of its position, is known as A. moment of inertia B. centre of ravity C. centre of percussion D. centr of mass

A. moment of inertia B. centre of gravity C. centre of percussion D. centre of mass

The loss of kinetic energy during elastic impact is zero A. Agree B.Disagree

A. Agree B.Disagree

Which of the following is a scalar quantity? A. Force B. Speed C. Velocity D. Accelration

A. Force B. Speed C. Velocity D. Accelration

When a train is rounding a curve, the side thrust on the wheel flanges is prevented by raising the outer edge of the rail. A. Yes B. No

A. Yes B. No

Frequency of vibration means the number of cycles per second A. Yes B. No

A. Yes B. No

The diesel engines are also known as A. compression ignition B. spark ignition

A. compression ignition B. spark ignition

In a four stroke cycle, the minimum temperature inside the engine cylinder occurs at the A. beginning of suction stroke B. end of suction stroke C. beginning of exhaust stroke B. end of exhaust stroke

In a four stroke cycle, the minimum temperature inside the engine cylinder occurs at the A. beginning of suction stroke B. end of suction stroke C. beginning of exhaust stroke B. end of exhaust stroke

In hit and miss governing , the fuel supply is cut-off completely during one or more number of cycles A. Yes B. No

In hit and miss governing , the fuel supply is cut-off completely during one or more number of cycles A. Yes B. No

The thermal efficiency of a standard Otto cycle for a compression ratio of 5.5 will be A.25% B.50% C.75% D. 100%

The thermal efficiency of a standard Otto cycle for a compression ratio of 5.5 will be A.25% B.50% C.75% D. 100%

Theoretically, a four stroke cycle engine should develop ____ power as that of a two stroke cycle engine. A. half B. same C. double D. four times

Theoretically, a four stroke cycle engine should develop ____ power as that of a two stroke cycle engine. A. half B. same C. double D. four times

Light Weight substances can be effective moderators. A. True B. False

Light Weight substances can be effective moderators. A. True B. False

The higher combustion chamber wall temperature in compression ignition engines will _____ knocking tendency. A. increase B. reduce C. not effect

The higher combustion chamber wall temperature in compression ignition engines will _____ knocking tendency. A. increase B. reduce C. not effect

The nuclear radiators produced in a reactor which must be sheilded are A. electrons B. neutron and gamma rays C. none of these

The nuclear radiators produced in a reactor which must be sheilded are A. electrons B. neutron and gamma rays C. none of these

If the speed of the engine is increased, the indicated power will A. increase B. decrease C. remain same

If the speed of the engine is increased, the indicated power will A. increase B. decrease C. remain same

Number of working strokes per min. for a two stroke cycle engine are ____ the speed of the engine in r.p.m A. equal to B. one-half C. twice D. four-times

Number of working strokes per min. for a two stroke cycle engine are ____ the speed of the engine in r.p.m A. equal to B. one-half C. twice D. four-times

Segmental chips are formed during machining


A. mild steel B. cast iron C. high speed steel D. high carbon steel

Segmental chips are formed during machining A. mild steel B. cast iron C. high speed steel D. high carbon steel

Internal gears can be made by A. hobbing B. shaping with pinion cutter C. shaping with rack cutter D. milling

Internal gears can be made by A. hobbing B. shaping with pinion cutter C. shaping with rack cutter D. milling

Drilling is an examble of
A. orthogonal cutting B. oblique cutting C. simple cutting D. uniform cutting

Drilling is an examble of
A. orthogonal cutting B. oblique cutting C. simple cutting D. uniform cutting

The lathe spindles are usually made hollow and provided with A. internal taper B. external taper C. internal and external taper D. no taper

The lathe spindles are usually made hollow and provided with A. internal taper B. external taper C. internal and external taper D. no taper

Crater wear is usually found while machining brittle materials. A. Correct B. Incorrect

Crater wear is usually found while machining brittle materials. A. Correct B. Incorrect

In electro-discharge machining, tool is made of A. brass B. copper C. copper tungsten alloy D. all of these

In electro-discharge machining, tool is made of A. brass B. copper C. copper tungsten alloy D. all of these

Ceramic tools has greater tool life than carbide tools. A. true B. false

Ceramic tools has greater tool life than carbide tools. A. true B. false

The cutting fluid mostly used for machining steel is A. water B. soluble oil C. dry D. heavy oils

The cutting fluid mostly used for machining steel is A. water B. soluble oil C. dry D. heavy oils

As the cutting speed increases, the tool cutting forces A. remain constant B. increases C. decreases

As the cutting speed increases, the tool cutting forces A. remain constant B. increases C. decreases

Soft materials can not be economically ground due to A. high temperature involved B. frequent wheel clogging C. rapid wheel wear D. low work piece stiffness

Soft materials can not be economically ground due to A. high temperature involved B. frequent wheel clogging C. rapid wheel wear D. low work piece stiffness

The neutral axis of the cross-section a beam is that axis at which the bending stress is A. zero B. minimum C. maximum D. infinity

The neutral axis of the cross-section a beam is that axis at which the bending stress is A. zero B. minimum C. maximum D. infinity

Eulers formula holds good only for A. short columns B. long columns C. both short and long columns D. weak columns

Eulers formula holds good only for A. short columns B. long columns C. both short and long columns D. weak columns

Compression members tend to buckle in the direction of the A. axis of load B. perpendicular to the axis of load C. minimum cross section D. least radius of gyration

Compression members tend to buckle in the direction of the A. axis of load B. perpendicular to the axis of load C. minimum cross section D. least radius of gyration

The maximum tangential stress in a thick cylindrical shell is always ____ the internal pressure acting on the shell. A. equal to B. less than C. greater than

The maximum tangential stress in a thick cylindrical shell is always ____ the internal pressure acting on the shell. A. equal to B. less than C. greater than

Principle plane is a plane on which the shear stress is A. zero B. minimum C. maximum

Principle plane is a plane on which the shear stress is A. zero B. minimum C. maximum

The shear force and bending moment are zero at the free end of a cantilever beam, if it carries a
A. point load at the free end B. point load at the middle of its length C. uniformly distributed load over the whole length D. none of the above

The shear force and bending moment are zero at the free end of a cantilever beam, if it carries a
A. point load at the free end B. point load at the middle of its length C. uniformly distributed load over the whole length D. none of the above

A rod of enclosed centrally in a tube and the assembly is tightened by rigid washers, if the assembly is subjected to a compressive load then A. rod is under compression B. tube is under compression C. both rod and tube are under compression D. tube is under tension and rod is under compression

A rod of enclosed centrally in a tube and the assembly is tightened by rigid washers, if the assembly is subjected to a compressive load then A. rod is under compression B. tube is under compression C. both rod and tube are under compression D. tube is under tension and rod is under compression

The unit of modulus of elasticity is same as those of


A. stress, strain and pressure B. stress, force and modulus of rigidity C. strain, force and pressure D. stress, pressure and modulus of rigidity

The unit of modulus of elasticity is same as those of


A. stress, strain and pressure B. stress, force and modulus of rigidity C. strain, force and pressure D. stress, pressure and modulus of rigidity

A pressure vessel is said to be a thin shell when it is made of thin sheets. A. agree B. disagree

A pressure vessel is said to be a thin shell when it is made of thin sheets. A. agree B. disagree

When a shaft is subjected to a twisting moment, every cross-section of the shaft will be under A. tensile stress B. compressive stress C. shear stress D. bending stress

When a shaft is subjected to a twisting moment, every crosssection of the shaft will be under A. tensile stress B. compressive stress C. shear stress D. bending stress

Power required to drive a centrifugal pump is directly proportional to ____of its impeller A. diameter B. square of diameter C. cube of diameter D. fourth power of diameter

Power required to drive a centrifugal pump is directly proportional to ____of its impeller A. diameter B. square of diameter C. cube of diameter D. fourth power of diameter

The sleeve or muff coupling is designed as a A. dun cylinder B. thick cylinder C. solid shaft D. hollow shaft

The sleeve or muff coupling is designed as a A. dun cylinder B. thick cylinder C. solid shaft D. hollow shaft

Screws used for power transmission should have A. sow efficiency B. high efficiency C. very fine threads D. strong teeth

Screws used for power transmission should have A. sow efficiency B. high efficiency C. very fine threads D. strong teeth

The rolling contact bearings are known as A. thick lubricated bearings B. plastic bearings C. thin lubricated bearings D. antifriction bearings

The rolling contact bearings are known as A. thick lubricated bearings B. plastic bearings C. thin lubricated bearings D. antifriction bearings

The size of the gear is specified by A. pressure angle B. pitch circle diameter C. circular pitch D. diameter pitch

The size of the gear is specified by A. pressure angle B. pitch circle diameter C. circular pitch D. diameter pitch

The ratio of endurance limit in shear to the endurance limit in flexure is A. 0.25 B. 0.40 C. 0.55 D. 0.70

The ratio of endurance limit in shear to the endurance limit in flexure is A. 0.25 B. 0.40 C. 0.55 D. 0.70

When plates are fastened by a rivet, the holes in the plates should be made by punching and reaming A. correct B. Incorrect

When plates are fastened by a rivet, the holes in the plates should be made by punching and reaming A. correct B. Incorrect

A shoe brake is commonly used in railway trains A. yes B. no

A shoe brake is commonly used in railway trains A. yes B. no

18/8 steel contains


A. 18% nickel and 8% chromium B. 18% chromium and 8% nickel C. 18% nickel and 8% vanadium D. 18% vanadium and 8% nickel

18/8 steel contains


A. 18% nickel and 8% chromium B. 18% chromium and 8% nickel C. 18% nickel and 8% vanadium D. 18% vanadium and 8% nickel

Oldham coupling is used to transmit power between two parallel shaft are slightly offset.
A. True B. false

Oldham coupling is used to transmit power between two parallel shaft are slightly offset.
A. True B. false

You might also like