Professional Documents
Culture Documents
Page 2
System Components
Outdoor Unit
Antenna Unit
Radio Cable
Indoor Unit
Page 3
Feed source
Parabolic reflec
Page 4
ODU
Flexibl e twist
Mount bracket
Page 5
PASOLINK
IDU
ODU
Antenna(0.3m)
Page 6
Page 7
Page 8
7 8
1. IF connector (to ODU) 2. 2Mbps interface (CH 9 to CH 16): impedance selector switch (75 or 120 ohms) 3. LAN Interface for main traffic: Port 1 and Port 2 (Optional) 4. WS/LAN: optional port for Wayside In/Out or 10BaseT 5. NMS LAN: for PNMS with LAN interface 6. Engineers Orderwire (EOW): receptacle for EOW headset 7. CALL: call buzzer for calling the opposite site of the transmission path 8. RESET: CPU reset switch for IDU
Page 9
10
11
12
13
9. LED:
14
14. OW / DSC / ASC (1) Order wire (2) Digital and Analog (VF) service channel
15
16
17
18
19
15. NMS / RA: for PNMS or remote access Local Craft Terminal (None PM Card)
16. LA Port: connector to PC for local access Local Craft Terminal or PNMT 17. Fuse: for primary DC line (be inserted in each plus and minus line)
18. 20SW : power switch
Rear Side
Front Side
IF connector to IDU
RX LEV MON
Page 12
Page 13
Page 14
Page 15
PASOLINK+ IDU
1+1 System
Page 16
OW: 1CH DSC: 2CH(64k/V11) ASC: 2CH(SDH) or 1CH(PDH) RS232C IF IN/OUT EXT PNMT LCT OW
6 Input 4 or O Output
EOW
ASC/DSC
ALM Out
CPU Reset
FUSE
FUSE
PS
V11 (PNMS)
WS(option)
FUSE
DC IN PWR SW
RS422(Sync/Async) or RS485
10Base-T
RS422 (Async)
10
11
12
13
14
15
16
17
24
23
22
21
20
19
18
1. IF connector (to ODU) 2. PNMT : Connect to PC for NMS 3. LCT : Connect to PC for Local Craft Terminal 4. EOW1 : Connect between IDUs for order wire 5. EOW2 : Connect between IDUs for order wire 6. NE1 : Connect between IDUs for NMS network 7. NE2 : Connect between IDUs for NMS network 8. LAN : Connect between IDUs for NMS network with LAN network 9. V11 : Connect between IDUs for NMS network with V.11 network 10. SC IN/OUT : Connector for Service Channel 11. ALM connector for parallel alarms (relay contact : Form-C) 12. ALM/AUX : Connector for Data Input/Data Output for house keeping
Page 18
13. R SW : Selector switch for switching b.w. previous firmware and new download firmware 14. EOW : Receptacle for headset 15. CALL : Call buzzer for calling opposite site 16. RESET : CPU reset switch for IDU 17. LEDs : MAINT : IDU maintenance condition ODU : ODU alarms IDU : IDU alarms PWR : Power switch on 18. DC IN : Connector for DC power in 19. SW : Power switch 20. Fuse : Fuses for primary DC line 21. Interface Card : STM-1 optical/STM-1 electrical, Nx2MB(G.703) 22. WS IN/OUT or 10Base-T interface card : Select card as an option, wayside(2.048Mbps), 10 Base-T or blanc panel 23. ESD : Connecting terminal for Electro Static Discharge 24. FG : Frame Ground Terminal
Page 19
Water-proof
There must be a gasket at the meeting place of the ODU and the antenna, or the meeting place of the ODU and the flexible twist. Smear the water-proof glue at the meeting place then wrap the water-proof tape and the then adhesive plaster at the outmost.
Be lack of water-proof and plaster!
Page 20
The waveguide ports must be identical! Dont be cross! The polarization orientation must be identical in one hop!
Page 21
Water-proof
Page 22
Page 23
This is unqualified!
Page 24
Page 25
Two terminals ought to be open! The adjusting line will be connected ODUs MON port with multimeter. Adjust multimeter to DVC 10 volt position. The multimeters display is bigger, the Rx power (Rx voltage) is better! During adjusting, one terminal is carrying on, another terminal must be quiet!
Rx LEV MON
Page 26
During the adjusting course, two cases are wrong: one terminals side-lobe meet another terminals side-lobe; one terminals side-lobe meet another terminals main-lobe! The only right case is that: one terminals main-lobe meet another terminals main-lobe!
wrong
wrong
right
Page 27
Rx power
Page 28