Professional Documents
Culture Documents
CD ROM
CD-ROM -(Compact Disk Read Only Memory) The standard type of CDROM drive which is now shipped and found in the majority of computers today.
CD-RW
CD-RW - (CD Rewritable) drive which is a popular alternative to the CD-R drive. CD-RW has the capability of being written to at least one thousand times. The drawback with CD-RW discs is with the lower reflectivity of the disc itself can limit the readability.
DVD ROM
DVD - (Digital Versatile Disc) New standard released in 1995 which originally was called Digital Video Disc and later changed to Digital Versatile Disc. DVD offers an initial storage capacity of 4.7GB (of digital information on a single-sided, single-layer disc the same diameter and thickness of a current CD-ROM
DVD WRITER
DVD - (Digital Versatile Disc) New standard released in 1995 which originally was called Digital Video Disc and later changed to Digital Versatile Disc. DVD offers an initial storage capacity of 4.7GB (of digital information on a single-sided, single-layer disc the same diameter and thickness of a current CD-ROM
COMBO DRIVE
Recordable CD
ReWritable CD
Physical size
Audio Capacity
Note
Mini CD
12 cm
74-80 min
Standard size
8 cm
21-24 min
185-210 MB
Mini-CD size
6 min
55 MB
CD-ROM Disc
A CD can stores 74 or 80 minutes of high fidelity audio and has a capacity of 682 MB (74-minute disc) or 737 MB (80-minute disc).
Short for Compact Disc-Read Only Memory, CD-ROM drives are CDPlayers inside computers that can have speeds in the range from 1x and beyond, and have the capability of playing audio CDs and computer data CDs. Below is a picture of the front and back of a standard CD-ROM drive.
This leaves the most challenging step next; removal of the front bezel and top metal cover. The following three images provide close-ups of the tabs which hold everything together (on my cdrom model anyway). Study these so you can see how they work and where they are, as you they will be mostly hidden from view until you get it apart.
At this point the tabs are the only thing holding it together, there are no screws left. Note that with the tray closed the door will hold the front plastic bezel pretty solidly in place. Do not attempt to forcibly remove the bezel or pull out the door at this time. But you will need to depress the tabs on the bezel (one on each side and one hidden on the top) and pull slightly forward on the bezel to unhook it from the metal cover. You will also need to gently pry the tabs on the metal cover which slide just under the top edge of the bezel so they are no longer under the bezel (as in the picture).
Use patience during this operation, as you do not want to break the bezel or the plastic tabs on it. Also be very careful if you use any prying tools, as you may scratch the bezel and can very easily apply too much force so that you break it; I did not use any prying tools (just a small blunt blade to depress the tabs). I found that pulling up the rear portion of the metal cover first allowed me to finally dislodge everything. Just take your time and be gentle.
One very important note of caution. See the picture above...that's the CDROM laser lens mechanism. It is extremely sensitive! Do not touch it, do not bump it, do not move it, and by all means do not allow anything to scratch it. You may want to temporarily tape a small piece of felt or cotton cloth over it to protect it.
I did not remove the two motor wires, although I could have unsoldered them if necessary. In my case though, I could just fold the board over being careful not to pull on the motor wires. Note that the curcuit board itself is just held in place with four small tabs and is very easy to remove (yours may have small screws).
Finally I have the board off and folded out of the way (only connected by the two motor wires). Remember, take is slow when pulling off the board. You may have accidentally left a wire of cable connected to the board someplace and you don't want to break any of the wires. Also it should go without saying, try not to touch any of the chips or electrical connections and use static electricity grounding techniques.
It should now be fairly easy to pull the tray out as if you were ejecting a disc. As you are manually turning all the motors, pull gently and slowly. It should not take much force, so if you have to pull hard stop and recheck that you have the tray properly unlocked.
The tray will pull out fully until it hits the stops. These stops prevent the tray from comming all the way out. On my model, there are two plastic tabs on either side of the tray which act as the physical stops.
By pulling out on the sides of the drive, the tray is able to slide past the stops and eventually comes all the way out of the drive.
Now you have most everything apart. But look at the door face closely, you'll see a small ring of felt or foam. This is the dust seal and it will probably be glued in place and can not be removed without destroying it. When painting the door face you want to protect this seal with tape so you don't paint it.
Also on the tray you may have four small nylon skid plates. These help protect the CDROM from rubbing against the tray and scratching it. If your tray has these, you will want to remove them and avoid painting the nylon skid plates.
And finally, the underside of the tray should have a row of gear teeth which the ejection motor drives. Avoid painting these teeth, and also avoid reoving any lubrication (if any) which may be on those teeth.
At last
Finally I have the drive disassembled enough to allow for a proper paint job.