Professional Documents
Culture Documents
TEST DATA:
For a 4 Foot by 4 Foot Unit. Tested with mill finish and no screen
Free area = 8.65 ft2 (0.804 m2)
Percent free area = 54%
Free area velocity at the point of beginning water penetration
(@0.01oz. /ft2 of free area based on a 15 minute interval test) = 804 FPM (4.08 m/s)
Maximum recommended air intake velocity = 604 FPM (3.07 m/s)
Air volume @ 604 FPM free area velocity = 5225 CFM (2.47 m3/s)
Pressure drop @ 604 FPM intake velocity = 0.07 in. H2O (16.6 Pa)
Maximum recommended air exhaust velocity = 1655.0 FPM (8.41 m/s)
Air Volume @ 1655 FPM free area velocity = 14315.8 CFM (6.76 m3/s)
Pressure drop @ 1655 FPM free area velocity = 0.50 in. H2O (124.2 Pa)
SUGGESTED SPECIFICATIONS:
GENERAL: Furnish and install where indicated on the drawings C/S 4 (101.6 mm) HIGH
PERPROMANCE FIXED EXTRUDED MULLION LOUVER MODEL A4080-A4085 as
manufactured by Construction Specialties, Inc. Cranford, New Jersey and Mississauga, Ontario.
Complete details shall be submitted to the architect for approval prior to fabrication.
MATERIAL: Heads, sills, jambs and mullions to be one piece structural members of 6063-T52
alloy with integral caulking slot and retaining beads. Mullions shall be sliding interlock with
integral internal drain(s). Heads to be one piece extrusion with gutter(s) designed to catch and
direct water to jamb and mullion drains. Closed cell compression gaskets shall be provided
between bottom of the mullion or jamb and the top of the sill to insure leak tight connections.
Blades to be one piece extrusions with reinforcing bosses. Extrusion thicknesses shall be as
follows: Heads, Sills, jambs and mullions: 0.081" (2.06 mm) or 0.125 (3.18 mm). Fixed Blades:
0.081 (2.06 mm). All fasteners to be aluminum or stainless steel. All louvers to be furnished
with 5/8 (15.87 mm) flattened expanded mesh, aluminum bird screen with a .055 (1.40 mm)
thick extruded aluminum frame. Screens and screen frames to be standard mill finish.
STRUCTURAL DESIGN: Structural supports shall be designed and furnished by the louver
manufacturer to carry a wind load of not less than_______ psf (Pascals). (Note: If this paragraph
is omitted or if the design wind load is not specified, the louvers will be manufactured in selfsupporting units up to a maximum of 5 (1524 mm) wide by 8 (2438 mm) high. Any additional
structural supports required to adequately secure these units within the opening shall be the
responsibility of others.)
TEST DATA: The louver manufacturer shall submit test data on a 4 x 4 (1.22 m x 1.22 m) unit
showing that the louver conforms to the following: (Based on a 15 min test duration)
Free area:
Free area velocity @ point of beginning water penetration (0.01 oz/ft2):
Intake pressure drop @ 0.01 oz.ft2 free area velocity:
Exhaust pressure drop at 1000 FPM (5.08 m/s) free area velocity:
FINISH: All louvers shall be finished with C/S Powder Coat, a coating to be 1.5 to 3 mil. thick
full strength 100% resin Fluoropolymer coating. Finish to allow zero VOCs to be emitted into
facility of application. Finish to adhere to a 4H Hardness rating. All finishing procedures shall be
one continuous operation in the plant of the manufacturer. The coating shall meet or exceed all
requirements of AAMA specification 2605-5 Voluntary Specification for High Performance
Organic Coatings on Architectural extrusions and Panels. The louver manufacturer shall supply
an industry standard 20-year limited warranty against failure or excessive fading of the
Fluoropolymer Powder Coat finish. This limited warranty shall begin on the date of material
shipment.
To download details and specifications visit www.c-sgroup.com. For technical and design assistance call 800-631-7379
PERFORMANCE DATA
A4080-A4085
PERFORMANCE
DATAMODELS
MODEL
A4080-A4085
AMCA defines the point of beginning water penetration as the free area
velocity at which the AMCA water test has yielded 0.01 or less ounces
of water per square foot of louver free area during a 15-minute test
period.
24
0.61
30
0.76
36
0.91
42
1.07
48
1.22
54
1.37
60
1.52
66
1.68
72
1.83
78
1.98
84
2.13
90
2.29
96
2.44
102
2.59
108
2.74
114
2.90
120
3.05
126
3.20
132
3.35
138
3.51
144
3.66
150
3.81
156
3.96
162
4.11
168
4.27
174
4.42
180
4.57
186
4.72
192
4.88
198
5.03
204
5.18
12
0.30
0.66
0.06
0.81
0.08
1.07
0.10
1.21
0.11
1.47
0.14
1.62
0.15
1.88
0.17
2.02
0.19
2.28
0.21
2.43
0.23
2.69
0.25
2.83
0.26
3.09
0.29
3.24
0.30
3.50
0.32
3.64
0.34
3.90
0.36
4.05
0.38
4.31
0.40
4.45
0.41
4.71
0.44
4.86
0.45
5.12
0.48
5.26
0.49
5.52
0.51
5.67
0.53
5.93
0.55
6.07
0.56
6.33
0.59
6.48
0.60
7.34
0.68
18
0.46
1.20
0.11
1.47
0.14
1.93
0.18
2.20
0.20
2.67
0.25
2.94
0.27
3.40
0.32
3.67
0.34
4.14
0.38
4.41
0.41
4.87
0.45
5.14
0.48
5.61
0.52
5.87
0.55
6.34
0.59
6.61
0.61
7.07
0.66
7.34
0.68
7.81
0.73
8.08
0.75
8.54
0.79
8.81
0.82
9.28
0.86
9.55
0.89
10.01
0.93
10.28
0.96
10.75
1.00
11.02
1.02
11.48
1.07
11.75
1.09
12.52
1.16
24
0.61
1.74
0.16
2.13
0.20
2.80
0.26
3.19
0.30
3.86
0.36
4.26
0.40
4.93
0.46
5.32
0.49
5.99
0.56
6.38
0.59
7.06
0.66
7.45
0.69
8.12
0.75
8.51
0.79
9.18
0.85
9.57
0.89
10.25
0.95
10.64
0.99
11.31
1.05
11.70
1.09
12.38
1.15
12.77
1.19
13.44
1.25
13.83
1.28
14.50
1.35
14.89
1.38
15.57
1.45
15.96
1.48
16.63
1.55
17.02
1.58
17.70
1.64
30
0.76
2.27
0.21
2.79
0.26
3.67
0.34
4.18
0.39
5.06
0.47
5.57
0.52
6.45
0.60
6.97
0.65
7.85
0.73
8.36
0.78
9.24
0.86
9.75
0.91
10.63
0.99
11.15
1.04
12.03
1.12
12.54
1.16
13.42
1.25
13.93
1.29
14.81
1.38
15.33
1.42
16.21
1.51
16.72
1.55
17.60
1.64
18.11
1.68
18.99
1.76
19.51
1.81
20.39
1.89
20.90
1.94
21.78
2.02
22.29
2.07
22.88
2.13
36
0.91
2.81
0.26
3.45
0.32
4.54
0.42
5.17
0.48
6.26
0.58
6.89
0.64
7.98
0.74
8.61
0.80
9.70
0.90
10.34
0.96
11.43
1.06
12.06
1.12
13.15
1.22
13.78
1.28
14.87
1.38
15.50
1.44
16.59
1.54
17.23
1.60
18.32
1.70
18.95
1.76
20.04
1.86
20.67
1.92
21.76
2.02
22.40
2.08
23.49
2.18
24.12
2.24
25.21
2.34
25.84
2.40
26.93
2.50
27.56
2.56
28.05
2.61
42
1.07
3.35
0.31
4.10
0.38
5.40
0.50
6.16
0.57
7.45
0.69
8.21
0.76
9.51
0.88
10.26
0.95
11.56
1.07
12.31
1.14
13.61
1.26
14.36
1.33
15.66
1.46
16.42
1.53
17.72
1.65
18.47
1.72
19.77
1.84
20.52
1.91
21.82
2.03
22.57
2.10
23.87
2.22
24.63
2.29
25.92
2.41
26.68
2.48
27.98
2.60
28.73
2.67
30.03
2.79
30.78
2.86
32.08
2.98
32.83
3.05
33.23
3.09
48
1.22
3.89
0.36
4.76
0.44
6.27
0.58
7.14
0.66
8.65
0.80
9.53
0.88
11.03
1.03
11.91
1.11
13.41
1.25
14.29
1.33
15.80
1.47
16.67
1.55
18.18
1.69
19.05
1.77
20.56
1.91
21.43
1.99
22.94
2.13
23.82
2.21
25.32
2.35
26.20
2.43
27.70
2.57
28.58
2.66
30.09
2.80
30.96
2.88
32.47
3.02
33.34
3.10
34.85
3.24
35.72
3.32
37.23
3.46
38.11
3.54
38.41
3.57
54
1.37
4.43
0.41
5.42
0.50
7.14
0.66
8.13
0.76
9.85
0.91
10.84
1.01
12.56
1.17
13.55
1.26
15.27
1.42
16.27
1.51
17.98
1.67
18.98
1.76
20.69
1.92
21.69
2.01
23.40
2.17
24.40
2.27
26.11
2.43
27.11
2.52
28.83
2.68
29.82
2.77
31.54
2.93
32.53
3.02
34.25
3.18
35.24
3.27
36.96
3.43
37.95
3.53
39.67
3.69
40.67
3.78
42.38
3.94
43.38
4.03
43.59
4.05
60
1.52
4.96
0.46
6.08
0.56
8.00
0.74
9.12
0.85
11.05
1.03
12.16
1.13
14.09
1.31
15.20
1.41
17.13
1.59
18.24
1.69
20.17
1.87
21.28
1.98
23.21
2.16
24.32
2.26
26.25
2.44
27.36
2.54
29.29
2.72
30.40
2.82
32.33
3.00
33.45
3.11
35.37
3.29
36.49
3.39
38.41
3.57
39.53
3.67
41.45
3.85
42.57
3.95
44.49
4.13
45.61
4.24
47.53
4.42
48.65
4.52
48.77
4.53
Intake
and
Exhaust
Mississauga, Ontario
895 Lakefront Promenade L5E 2C2
Telephone: (888) 895-8955
Fax: (905) 274-6241
A member of the C/S Group of Companies
For assistance with overseas requirements,
call C/S International (908) 236-0800
Copyright April 2010. Construction Specialties, Inc., reserves the right
to make design changes or to withdraw any design without notice.