Professional Documents
Culture Documents
TYPE 222100
HOME BUTCHER
UK ARAB IR
13
Feb 08 V1
ART. 222100
Read these instructions thoroughly first and keep them for future reference. Check whether the voltage in the home corresponds with that of the appliance. Only connect this appliance to an earthed electric socket. Remove all packaging materials and stickers from the appliance. Clean the appliance and all removable accessories and dry them thoroughly (see Cleaning and maintenance). Place the motor unit on a flat and stable surface.
PARTS
1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13. 14. 15. 16. 17. 18. Pusher Tray Cutter housing Release button Indicator light Motor unit Temporary Stop/Reversal button(Stop/REV) Switch ON/OFF button Fine grinding disc Medium grinding disc Worm shaft Cutter blade Coarse grinding disc Screw ring Separator Sausage horn Former Cone
HOW TO USE
Mincing See below figure 2
1. Insert the worm shaft into the cutter housing, the plastic end first. Fit the cutter blade unit onto the other end of worm shaft. (The cutting edge should be placed at the front side). And then you can also fit the coarse/medium/fine grinding disc (Depending on the consistency you prefer). Make sure the notch of the grinding disc fit into the projection on the opening of cutter house. Fit the screw ring on the cutter housing by turning the screw ring clockwise until it is properly fastened. 2. Fit the cutter housing on the motor unit. The lugs on the motor unit must fit precisely into the slots on the cutter housing. Rotate the cutter housing anti-clockwise until hear a click. The cutter housing is then locked in the position You can remove the cutter housing by pressing the release button on the appliance and turning the cutter housing clockwise. 3. Place the tray on the upright part of the cutter housing. 4. Now the appliance is ready for mincing
MINCING:
Cut the meat into 10 cm long, 2 cm thick strips. Remove bones, pieces of gristle and sinews as much as possible. Note: never use frozen meat!
Place the meat on the tray. Use the pusher to gently push the meat into the cutter housing. For steak tartare, mince the meat with the medium grinding disc twice.
MAKING SAUSAGES
See below figure 3
1. Mince the meat(see Mincing sections) 2. Switch off the appliance. 3. Press the release button on the appliance and turn the cutter housing clockwise to remove it from the motor unit. Note: Make sure the appliance is switched off and stops running before you remove the cutter housing. 4. Remove the screw ring by turn it anti-clockwise. 5. Remove the grinding disc. 6. Fit separator, sausage horn on the metal end of worm shaft. Then fit the screw ring on the cutter housing by turning the screw ring clockwise until it is properly fastened. Make sure the notch of separator fit into the projection on the opening of cutter house. 7. Fit the cutter housing on the motor unit. The lugs on the motor unit must fit precisely into the slots on the cutter housing. Rotate the cutter housing anti-clockwise until hear a click. The cutter housing is then locked in the position. 8. Place the tray on the upright part of the cutter housing. 9. Now the appliance is ready for making sausages.
MAKING SAUSAGES:
Put the ingredients in the tray. Use the pusher to gently push the meat into the cutter housing. Put the sausage skin in lukewarm water for 10 minutes. Then slide the wet skin onto the sausage horn. Push the (seasoned) minced meat into the cutter housing. If the skin gets stuck onto the sausage horn, wet it with some water.
MAKING KEBBE
See below figure 4
1. Insert the worm shaft into the cutter housing, the plastic end first. 2. Fit the cone on the metal end of worm shaft, and then fit the former. Make sure the notch of the cone fit into the projection on the opening of cutter house. 3. Fit the screw ring on the cutter housing by turning the screw ring clockwise until it is properly fastened. 4. Fit the cutter housing on the motor unit. The lugs on the motor unit must fit precisely into the slots on the cutter housing. Rotate the cutter housing anti-clockwise until hear a click. The cutter housing is then locked in the position 5. Place the tray on the upright part of the cutter housing, 6. The appliance is ready for making kebbe.
MAKING KEBBE:
Feed the prepared kebbe mixture through the kebbe maker. Cut the continuous hollow cylinder into the desired lengths and user as required Kebbe is a traditional Middle Eastern dish made primarily of lamb and bulgur wheat which are minced together to form a paste the mixture is extruded through the kebbe maker and cut into short lengths. The tubes can then be stuffed with a minced meat mixture, the ends pinched together and then deep fried.
TEMP STOP/REVERSE
1. Keep pressing REV button when the appliance is in the mode of switch on, the appliance temporarily stops working. Release the button, the appliance resumes working. 2. If the appliance is blocked, switch off the appliance first and press REV button, the worm shaft will turn in the reverse direction. Then the appliance can renew its normal condition.
PRINCESS TIPS
- This appliance is only suitable for household use. Dont use outside. - Check if the voltage indicated on the appliance corresponds to the local mains voltage before you connect to the appliance. - Never use any accessories of parts from other manufactures. Your guarantee will become invalid if such accessories or parts have been used. - Do not use the appliance if the mains cord, the plug or other parts are damaged. - If the mains cord of this appliance is damaged, it must always be replaced by manufacture or a service center authorized, In order to avoid hazardous situations - Make sure every part fits in its position before you switch on the appliance. - Never use you finger or an object to push ingredients down the feed tube while the appliance is running. Only the pusher is to be used for this purpose. - Keep the appliance out of the reach of children. - Never let the appliance run unattended. - Unplug the power cord from power supply socket before detaching and installing any accessory. - Wait until moving parts have stopped running before you remove the parts of the appliance. - Do not attempt to grind bones, nuts or other hard units. - Never reach into the cutter housing. Always use the pusher. - Unplug the appliance immediately after use. - Never operate the appliance continuously for more than 3 minutes at 800W. - Children should be supervised to ensure that they do not play with the appliance. - The use of this appliance by children or persons with a physical, sensory, mental or motorial disability, or lack of experience and knowledge can give cause to hazards. Persons responsible for their safety should give explicit instructions or supervise the use of the appliance.
MAINTENANCE:
- Mincer meat only without bones and skin - Wash the mincer every time after use and wipe dry, coat it with a few drops of edible oil to prevent rusting DONT IMMERSE THE MOTOR UNIT IN WATER OR IN OTHER LIQUIDS. IF THIS HAPPES DONT USE THE APPLIANCE ANY MORE; DISPOSE OF THE APPLIANCE.
STORAGE
You can store the power cord in the power cord storage on the bottom of the appliance. The separator, sausage horn, former and cone can be stored in the pusher. See figure 5
Fig.5
WARNING: ON NO ACCOUNT SHOULD EITHER THE LIVE OR NEUTRAL WIRES BE CONNECTED TO THE EARTH TERMINAL
With this appliance, if a 13 amp plug is used a 13 amp fuse should be fitted. If any other type of plug is used, a 15 amp fuse must be fitted either in the plug or at the distribution board
ART. 222100
10
11
12
ART. 222100
13
14
15
PRINCESS 2008