Professional Documents
Culture Documents
8S651MP-RZ / 8S651MP-RZ-C
User's Manual
Rev. 1001 12ME-8S651MPRZ-1001
Copyright
2003GIGABYTE TECHNOLOGYCO., LTD Copyright by GIGA-BYTETECHNOLOGY CO.,LTD. ("GBT"). No part of this manual may be reproduced or transmitted in any from without the expressed, written permission of GBT.
Trademarks
Third-party brands and names are the propertyof their respective owners.
Notice
Please do not remove any labels on motherboard, this may void the warranty of this motherboard. Due to rapid change in technology, some of the specifications might be out of date before publication of this booklet. The author assumes no responsibility for any errors or omissions that may appear in this document nor does the author make a commitmentto update the informationcontained herein.
Motherboard 8S651MP-RZ
Jun. 25 ,2004
Jun. 25, 2004
English
Table of Content
Chapter 1 Introduction ................................................................................................ 5
Features Summary ..............................................................................................................................5 8S651MP-RZ Series Motherboard Layout .........................................................................................7 Block Diagram .....................................................................................................................................8 Hardware Installation Process ............................................................................................................9 Step 1: Install the Central Processing Unit (CPU) .............................................................................9 Step 1-1: CPU Installation .........................................................................................................10 Step 1-2: CPU Cooling Fan Installation ....................................................................................10 Step 2: Install memory modules ....................................................................................................... 11 Step 3: Install expansion cards .........................................................................................................12 Step 4: Install I/O Peripherals Cables ..............................................................................................12 Step 4-1: I/O Back Panel Introduction .......................................................................................12 Step 4-2: Connectors Introduction ..............................................................................................13
-4-
Chapter 1 Introduction
Features Summary
Motherboard CPU 8S651MP-RZ Series: 8S651M P-RZ / 8S651M P-RZ-C Socket 478 for Intel M icro FC-PGA2 Pentium 4 processor Support Intel Pentium 4 (Northwood, 0.13 m) processor Intel Pentium 4 400/533 M Hz FSB 2nd cache depends on CPU North Bridge:SiS 651 South Bridge:SiS 962L 2 184-pin DDR sockets Supports DDR200/DDR266/DDR333 Supports up to 2 un-buffer Double-sided DIMM DDR200/266/333 Supports up to 2GB (Max) Supports only 2.5V DDR DIMM 1 Universal AGP slot (4X) device support 3 PCI slot 2 IDE bus m aster (UDMA33/ATA66/ATA100/ATA133) IDE ports for up to 4 ATAPI devices Supports PIO mode3,4 (UDM A 33/ATA66/ATA100/ATA133) IDE & ATAPI CD-ROM Floppy port supports 2 FDD with 360K, 720K,1.2M, 1.44M and 2.88M bytes 1 Parallel port 1 Serial port (COMA),1 VGA port,COM B on board 6 x USB 2.0/1.1 (2 x Rear, 4 xFront by cable) 1 Front Audio Connector 1 IrDA connector for IR PS/2 Keyboard interface and PS/2 Mouse interface Build in RTL8201 Chipset Realtek ALC655 CODEC Line Out / 2 front speaker Line In / 2 rear speaker(by s/w switch) M ic In / center& subwoofer(by s/w switch) SPDIF Out /SPDIF In CD_In / Game Port Licensed Award BIOS Supports Q-Flash W83697HF to be continued...... For 8S651M P-RZ only. * -5Introduction
English
Chipset Memory
English
Hardware M onitor
CPU/System Fan Revolution detect CPU/System Fan Control CPU Overheat Warning System Voltage Detect
Supports EasyTune 4 Supports @BIOS 24.4cm x 21.5cm M icro ATX size form factor, 4 layers PCB.
Please set the CPU host frequency in accordance with your processor's specifications. We don't recommend you to set the system bus frequency over the CPU's specification because these specific bus frequencies are not the standard specifications for CPU, chipset and most of the peripherals. Whether your system can run under these specific bus frequencies properly will depend on your hardware configurations, including CPU, Chipsets, Mem ory, Cards .etc.
-6-
English
A TX_12V
*
CPU_FAN
KB_MS
USB_LAN
COMA
LPT
8S651MP-RZ
VGA
SiS 651
DDR1
DDR2
SiS 962L
CI
PCI3
BAT
COMB
PWR_LE D
24.4 cm
English
Block Diagram
Pentium 4 Socket 478 CPU AGP 4X AGPCLK (66MHz) VGA Port CPUCLK+/- (100/133 MHz)
System Bus 400/533 MHz DDR SiS 651 200/266/333MHz ZCLK (66MHz) HCLK+/- (100/133 MHz) 66 MHz 33 MHz 14.318 MHz 48 MHz BIOS SiS 962L Game Port LPC BUS W83697HF Floppy LPT Port
3 PCI
RJ45
RTL8201 *
AC97 Link
PCICLK (33MHz)
PS/2 KB/Mouse
MIC LINE-IN
LINE-OUT
COM Ports
CLK GEN
ZCLK (66MHz) CPUCLK+/- (100/133 MHz) AGPCLK (66MHz) HCLK+/- (100/133 MHz)
-8-
English
Step 4 Step 1
Step 2
Step 4
Step 4
Step 3
English
Figure 2. Locate Pin 1 in the socket and look for a (golden) cut edge on the CPU upper corner. Insert the CPU into the socket. (Do not force the CPU into the socket.) Then m ove the socket lever to the locked position while holding pressure on the center of the CPU.
Figure 2. Fasten the cooling fan supporting-base onto the CPU socket on the motherboard.
Figure 3. Make sure the CPU fan is plugged to the CPU fan connector, than install complete.
- 10 -
English
Notch
DDR Support Unbuffered DDR DIMM Sizes type: 64 Mbit (2Mx8x4 banks) 64 Mbit (1Mx16x4 banks) 128 Mbit(2Mx16x4 banks) 256 Mbit(8Mx8x4 banks) 512 Mbit(16Mx8x4 banks) 512 Mbit(8Mx16x4 banks) 128 Mbit(4Mx8x4 banks) 256 Mbit(4Mx16x4 banks)
1. The DIM M socket has a notch, so the DIM M memory module can only fit in one direction.
2. Insert the DIMM m emory module vertically into the DIM M socket. Then push it down.
3. Close the plastic clip at both edges of the DIMM sockets to lock the DIM M m odule. Reverse the installation steps when you wish to rem ove the DIM M module.
- 11 -
English
AGP Card
v LAN port*
LAN is fast Ethernet with 10/100M bps speed.
w USB port
Before you connect your device(s) into USB connector(s), please make sure your device(s) such as USB keyboard, mouse, scanner, zip, speaker...etc. Have a standard USB interface. Also m ake sure your OS supports USB controller. If your OS does not support USB controller, please contact OS vendor for possible patch or driver upgrade. For more inform ation please contact your OS or device(s) vendors.
- 12 -
z VGA port
Monitor can be connected to VGA port.
English
{ Game/MIDI port
This connector supports joystick, M IDI keyboard and other relate audio devices.
} Line In jack
Devices like CD-ROM , walkm an etc. can be connect to Line In jack.
~ MIC In jack
Microphone can be connect to MIC In jack. After installation of the audio driver, you are able to use 2/4/6-channel audio feature by software selection. You can connect "Front speaker" to "Line Out" jack, Connect "Rear speaker" to "Line In" jack and connect "Center/Subwoofer" to "MIC In" jack.
5 19 18 4 15 14 17 16 10 9 8
1) 2) 3) 4) 5) 6) 7) 8)
11) F_AUDIO 12) SUR_CEN 13) CD_IN 14) SPDIF_IO 15) I R 16) F_USB1/F_USB2 17) COMB 18) CI 19) CLR_CMOS
- 13 Hardware Installation Process
English
3 1
4 2
Pin No. 1 2 3 4
20
10
Pin No. Definition 1 3.3V 2 3.3V 3 GND 4 VCC 5 GND 6 VCC 7 GND 8 Power Good 9 5V SB (stand by 10 +12V
+5V)
Pin No. Definition 11 3.3V 12 -12V 13 GND 14 PS_ON(soft on/off) 15 GND 16 GND 17 GND 18 -5V 19 VCC 20 VCC
Pin No. 1 2 3
- 14 -
English
Pin No. 1 2 3
2 IDE2 IDE1
34
33
- 15 -
English
7) DIMM_LED
Do not remove memory modules while DIMM LED is on. It might cause short or other unexpected damages due to the 2.5V stand by voltage. Remove m emory m odules only when AC Power cord is disconnected.
So ft Pow er Me ssa g e LED /Po w e r / Sle ep L ED PW MPD MPD + 21 1 1 ID E H ard Di sk Acti ve L ED HD+ HD R STR ST+ Re set Switch PW + 1 1 NC SPK+ 1 SP K20 19 Co nnector Spea ker Conne ctor
Pin 1:LED anode(+) Pin 2: LED cathode(-) Pin1: VCC(+) Pin 2- Pin 3: NC Pin4: Data(-) Open:NormalOperation Close: Reset Hardware System Open:NormalOperation Close: Power On/Off Pin 1:LED anode(+) Pin 2: LED cathode(-) NC
- 16 -
9 ) PWR_LED
PWR_LED is connect with the system power indicator to indicate whether the system is on/off. It will blink when the system enters suspend mode. If you use dual color LED, power LED will turn to another color.
English
Pin No. 1 2 3
- 17 -
English
10
12) SUR_CEN
Please contact your nearest dealer for optional SUR_CEN cable.
1 5
2 6
Pin No. 1 2 3 4 5 6
13) CD_IN
Connect CD-ROM or DVD-ROM audio out to the connector.
Pin No. 1 2 3 4
- 18 -
English
Pin No. 1 2 3 4 5 6
15) I R
Make sure the pin 1 on the IR device is aling with pin one the connector. To enable the IR function on the board, you are required to purchase an option IR m odule. Be careful with the polarity of the IR connector. For optional IR cable, please contact your local dealer.
Pin No. 1 2 3 4 5
2 1
10 9
- 19 -
English
10
Open: Normal
Close: Clear CM OS
- 20 -
English
ENTERING SETUP
Pow ering ON the computer and pressing <Del> immediately w ill allow y ou to enter Setup. If y ou require m ore adv anced BIOS s ettings , pleas e go to "Adv anc ed BIOS" s etting m enu. To enter Adv anced BIOS s etting menu, press "Ctrl+F1" key on the BIOS sc reen.
CONTRO L KEYS
< >< >< <Enter> <Esc> <+/PgUp> <-/PgDn> <F1> <F2> <F5> <F6> <F7> <F8> <F9> <F10> >< > Mov e to select item Select Item Main Menu - Quit and not sav e c hanges into CMOS Status Page Setup Menu and Option Page Setup Menu - Ex it current page and return to Main Menu Increase the numeric v alue or make changes Decrease the numeric v alue or make changes General help, only for Status Page Setup Menu and Option Page Setup Menu Item Help Restore the prev ious CMOS v alue from CMOS, only for Option Page Setup Menu Load the file-safe default CMOS v alue from BIOS default table Load the Optim ized Defaults Q-Flash utility Sy stem Inform ation Sav e all the C MOS changes, only for Main Menu
Main Menu
The on-line description of the highlighted setup function is display ed at the bottom of the sc reen.
- 21 -
BIOS Setup
English
If you can't find the setting you want, please press "Ctrl+F1" to search the advanced option hidden. Standard CMOS Features
This setup page includes all the items in s tandard c ompatible BIOS.
Integrated Peripherals
This setup page includes all onboard peripherals.
PnP/PCI Configuration
This setup page includes all the configurations of PCI & PnP ISA resources.
PC Health Status
This setup page is the Sy stem auto detect Temperature, v oltage, fan, s peed.
Frequency/Voltage Control
This setup page is control CPU clock and frequency ratio.
Top Performance
If y ou w ish to max imize the performance of y our sy stem, set "Top Performance" as "Enabled".
- 22 -
English
Driv e A Driv e B Flopp y 3 Mode S uport Holt On Base M emory Exte nded Me mory Total Memory higf: M ove Enter: Select F5: P revious V alues
Date
The date format is <w eek>, <month>, <day >, <y ear>. Week The w eek, from Sun to Sat, determined by the BIOS and is display only Month The m onth, Jan. Through Dec. Day The day , from 1 to 31 (or the max imum allow ed in the m onth) Year The y ear, from 1999 through 2098
Time
The times format in <hour> <m inute> <second>. The time is c alc ulated bas e on the 24-hour military -time clock. F or ex ample, 1 p.m. is 13:00:00.
- 23 -
BIOS Setup
English
Drive A / Dri ve B
The category identifies the ty pes of floppy disk driv e A or driv e B that has been installed in the computer. None No floppy driv e installed 360K, 5.25" 5.25 inch PC-ty pe standard driv e; 360K by te capacity . 1.2M, 5.25" 5.25 inch AT-ty pe high-density driv e; 1.2M by te capacity (3.5 inch w hen 3 Mode is Enabled). 720K, 3.5" 3.5 inch double-sided driv e; 720K by te capacity 1.44M, 3.5" 3.5 inch double-sided driv e; 1.44M by te capacity . 2.88M, 3.5" 3.5 inch double-sided driv e; 2.88M by te capacity .
Halt on
The c ategory determines w hether the computer w ill stop if an error is detected during pow er up. No Errors The sy stem boot w ill not s top for any error that may be detected and y ou w ill be prompted. All Errors Whenev er the BIOS detects a non-fatal error the s y stem w ill be stopped. All, But Key board The s y stem boot w ill not stop for a key board error; it w ill stop for all other errors . (Default v alue) All, But Disk ette The sy stem boot w ill not stop for a disk error; it w ill stop for all other errors. All, But Disk /Key The sy stem boot w ill not stop for a key board or disk error; it w ill stop for all other errors.
Memory
The c ategory is display -only w hich is determined by POST (Pow er On Self Test) of the BIOS.
Base Memory
The POST of the BIOS w ill determine the amount of base (or conv entional) memory ins talled in the sy stem. The v alue of the base memory is ty pic ally 512K for sy stems w ith 512K memory installed on the motherboard, or 640K for sy stems w ith 640K or more memory installed on the motherboard.
Extended Memory
The BIOS determines how much ex tended memory is present during the POST. This is the am ount of memory located abov e 1 MB in the CPU 's memory address map.
- 24 -
English
Password Check
Sy stem Setup The sy stem w ill not boot and w ill not access to Setup page if the correct passw ord is not entered at the prompt. The sy stem w ill boot but w ill not access to Setup page if the correct passw ord is not entered at the prompt. (Default v alue)
- 25 -
BIOS Setup
English
Integrated Peripherals
CMOS Setup Ut ility-Co pyright (C) 1984 -2004 Aw ard Soft ware Inte grated Periphe rals IDE1 Conductor Cable IDE2 Conductor Cable On-Chip Primary PCI IDE On-Chip Secondary PCI IDE AC97 Audio Onboard LAN Device (*) System Share Memory Size USB Controller USB Legacy Support Init Display First Onboard Serial Port A Onboard Serial Port B Serial Port B Mode Onboard Parallel Port Parallel Port Mode x EPP Mode Select ECP Mode Use DMA Game Port Address Midi Port Address Midi Port IRQ higf: M ove Enter: Select F5: P revious V alues [Auto] [Auto] [Enabled] [Enabled] [Enabled] [Enabled] [32MB] [Enabled] [Disabled] [AGP] [3F8/IRQ4] [2F8/IRQ3] [Normal] [378/IRQ7] [ECP] EPP1.7 [3] [201] [330] [10] +/-/ PU/PD: V alue F10: Save F6: Fa il-Save De fault Item Help Menu Level u [Auto] Auto-detect IDE cable type [ATA66/100/133] Set Conductor cable to ATA66/100/133 (80-pins) [ATA33] Set Conductor cable to ATA33(40-pins)
AC97 Audio
Enabled Disabled
"*" F or 8S651MP-RZ only.
Enable onboard AC'97 audio function. (Default v alue) Disable this function.
- 26 -
(*)
English
Enable onboard LAN dev ice. (Default v alue) Disable onboard LAN dev ice.
USB Controller
Enabled Disabled Enable USB Controller. (Default v alue) Disable USB Controller.
y ou to determine w hich Infra Red(IR) function of Onboard I/O chip) Set onboard I/O chip UART to ASKIR Mode. Set onboard I/O chip UART to IrDA Mode. Set onboard I/O chip UART to Normal Mode. (Default Value) Enable onboard LPT port and address is 378/IRQ7. (Default Value) Enable onboard LPT port and address is 278/IRQ5. Disable onboard LPT port. Enable onboard LPT port and address is 3BC/IRQ7.
- 27 -
BIOS Setup
English
- 28 -
English
Soft-off by PWR_BTTN
Off Suspend The user press the pow er button once, he can turn off the sy stem. (Default Value) The user press the pow er button once, then the sy stem w ill can enter suspend mode.
ModemRingOn
Disabled Enabled Disable Modem Ring on function. Enable Modem Ring on function. (Default Value)
Power On by Keyboard
Passw ord Any Key Disabled Input passw ord (from 1 to 8 characters) and press Enter to set the Key board Pow er On Passw ord. Set Key board pow er on by any key . Disable this function. (Default Value)
Power On by Mouse
Enabled Disabled Enable Pow er On by Mouse function. Disable this function. (Default Value)
Resume by Alarm
You can set "Resume by Alarm" item to enabled and key in Data/time to pow er on sy stem. Disabled Disable this function. (Default Value) Enabled Enable alarm function to POWER ON sy stem. If RTC Alarm Lead To Pow er On is Enabled. Month Alarm : NA, 1~12 Day (of Month) : 0~31 Time ( hh: mm: ss) : (0~23) : (0~59) : (0~59) - 29 BIOS Setup
English
PnP/PCI Configurations
CMOS Setup Ut ility-Co pyright (C) 1984 -2004 Aw ard Soft ware PnP/ PCI Con figurat ions PCI 1 IRQ Assig nment PCI 2 IRQ Assig nment PCI 3 IRQ Assig nment [Au to] [Au to] [Au to] Item Help Menu L evel} Devic e(s) using this INT: Disp lay Cn trlr -Bus 1 Dev 0 F unc 0
- 30 -
English
English
Frequency/Voltage Control
CMOS Setup Ut ility-Co pyright (C) 1984 -2004 Aw ard Soft ware Frequ ency/Vol tage Con trol CPU Clock Ratio Linear Frequency Control x CPU Clock (MHz) x DRAM Clock (MHz) x AGP Clock (MHz) x PCI Clock (MHz) [10X] [Disabled] 100 AUTO AUTO AUTO Item Help Menu Level
CPU Clock
100~355 Select CPU Clock to 100MHz~355MHz. If y ou use FSB400 Pentium 4 processor, please set "CPU Clock" to 100MHz.If y ou use FSB533 Pentium 4 processor, please set "CPU Clock" to 133MHz. If y ou use FSB800 Pentium 4 processor, please set "CPU Clock" to 200MHz. Incorrect using it may cause y our sy stem broken. For pow er End-User use only !
English
Top Performance
CMOS Setup Ut ility-Co pyright (C) 1984 -2004 Aw ard Soft ware } } } } } } } Stan dard CM OS Feat ures Top Perform ance Adva nced BI OS Feat ures Load Fail-Sa fe Defa ults Inte grated Periphe rals Perform ance Load Optimiz ed Defa ults Top Powe r Manag ement S etup Set Supervis Disab led..... ......... ........ ...[n] or Pass word PnP/ PCI Con figurat ions Set ...[ ] Enabl ed...... ......... ........ U ser Pass word PC H ealth St atus Save & Exit S etup Frequ ency/Vol tage Con trol Exit Without S aving higf: Selec t Item hi: M ove ENTER: Accept F10: Save & Exit S etup ESC: Abort Time, Date, Har d Disk Ty pe...
If y ou w ish to max imize the performance of y our sy stem, set "Top Performance" as "Enabled". Disabled Disable this function. (Default Value) Enabled Enable Top Performance function. "Top Performance" w ill increase H/W w orking speed. Different sy stem configuration (both H/W com ponent and OS) w ill effect the result. F or ex ample, the s ame H/W configuration might not run properly w ith Window s XP, but w orks smoothly w ith Window s N T. Therefore, if y our s y stem is not perform enough, the reliability or stability problem w ill appear sometimes, and w e w ill recommend y ou disabling the option to av oid the problem as mentioned abov e.
Fail-Safe defaults contain the mos t appropriate v alues of the sy stem parameters that allow minimum sy stem perform ance. - 33 BIOS Setup
English
Selecting this field loads the factory defaults for BIOS and Chipset Features w hich the sy stem automatically detects.
When y ou select this function, the follow ing message w ill appear at the center of the screen to assist y ou in creating a pas sw ord. Ty pe the passw ord, up to eight c haracters, and pres s <Enter>. You w ill be ask ed to c onfirm the pas sw ord. T y pe the pass w ord again and press <Enter>. You may also press <Es c> to abort the selec tion and not enter a pass w ord. To disable pass w ord, jus t press <Enter> w hen y ou are prompted to enter pass w ord. A mess age "PASSWORD DISABLED" w ill appear to confirm the pass w ord being disabled. Once the passw ord is disabled, the sy stem w ill boot and y ou c an enter Setup freely . The BIOS Setup program allow s y ou to specify tw o separate passw ords: SUPERVISOR PASSWOR D and a USER PASSWORD. When disabled, any one m ay access all BIOS Setup program function. When enabled, the Superv is or passw ord is required for entering the BIOS Setup program and hav ing full configuration fields, the User passw ord is required to access only basic items. If y ou select "Sy stem" at "Passw ord Check" in Adv anc e BIOS Features Menu, y ou w ill be prompted for the passw ord ev ery time the sy stem is rebooted or any time y ou try to enter Setup Menu. If y ou select "Setup" at "Passw ord Check" in Adv ance BIOS Features Menu, y ou w ill be prompted only w hen y ou try to enter Setup.
- 34 -
English
Ty pe "Y" w ill quit the Setup Utility and sav e the user setup v alue to RTC CMOS. Ty pe "N" w ill return to Setup Utility .
Ty pe "Y" w ill quit the Setup Utility w ithout sav ing to RTC CMOS. Ty pe "N" w ill return to Setup Utility .
- 35 -
BIOS Setup
English
Massage: Some device drivers will restart your system automatically. After restarting your system the "Xpress Install" will continue to install other drivers.
The "Xpress Install" uses the"Click and Go" technology to install the drivers automatically. Just select the drivers you want then click the "GO" button. The will execute the installation for you by itself.
Click "GO".
- 36 -
English
Item Description
SiS 650/650GL/650GX/651 VGA Driver VGA driver for VGA integrated SiS 650/650GL/650GX/651chipset. USB Patch for WinXP This patch driver can help you to resolve the USB device wake up S3 hang up issue in XP. SiS PCI Lan Driver ( * ) SiS 962L/963L LAN driver. RealTek AC97 Audio Driver Install RealTek AC97 audio driver. SIS USB 2.0 Driver It is recommended that you use the Microsoft Windows update for the most updated driver for XP/2K.
If your CD doesn't have SiS USB2.0 driver, please download the USB2.0 driver from Microsoft website (www.microsoft.com) for USB2.0 devices support. Please also note that Microsoft USB2.0 driver is currently supported by Windows XP and Windows 2000 only. Once we get the latest SiS USB2.0 driver for Windows 98 and Windows ME, we will put the driver on GIGABYTE website asap. (http://www.gigabyte.com.tw).
For USB2.0 driver support under Windows XP operating system, please use Windows Service Pack. After install Windows Service Pack, it will show a question mark "?" in "Universal Serial Bus controller" under "Device Manager". Please remove the question mark and restart the system (System will auto-detect the right USB2.0 driver). * For 8S651MP-RZ only. - 37 Driver Installation
English
8S651MP-RZ Series Motherboard
- 38 -
English
- 39 -
Driver Installation
English
CONTACT US
Contact us via the information in this page all over the world.
Taiwan Gigabyte Technology Co., Ltd. Address: No.6, Bau Chiang Road, Hsin-Tien, Taipei Hsien, Taiwan, R.O.C. Tel: 886 (2) 8912-4888 Fax: 886 (2) 8912-4004 Tech. Support: http://tw.giga-byte.com/TechSupport/ServiceCenter.htm Non-Tech. Support (Sales/Marketing issues): http://ggts.gigabyte.com.tw/nontech.asp Website: http://www.gigabyte.com.tw USA G.B.T. INC. Address: 17358 Railroad St, City of Industry, CA 91748. Tel: 1 (626) 854-9338 Fax: 1 (626) 854-9339 Tech. Support: http://www.giga-byte.com/TechSupport/ServiceCenter.htm Non-Tech. Support (Sales/Marketing issues): http://ggts.gigabyte.com.tw/nontech.asp Website: http://www.giga-byte.com Germany G.B.T. Technology Trading GmbH Tel: 49-40-2533040 49-01803-428468 (Tech.) Fax: 49-40-25492343 (Sales) 49-01803-428329 (Tech.) Tech. Support: http://de.giga-byte.com/TechSupport/ServiceCenter.htm Non-Tech. Support (Sales/Marketing issues): http://ggts.gigabyte.com.tw/nontech.asp Website: http://www.gigabyte.de Japan Nippon Giga-Byte Corporation Website: http://www.gigabyte.co.jp U.K G.B.T. TECH. CO. LTD. Tel: 44-1908-362700 Fax: 44-1908-362709 Tech. Support: http://uk.giga-byte.com/TechSupport/ServiceCenter.htm Non-Tech. Support (Sales/Marketing issues): http://ggts.gigabyte.com.tw/nontech.asp Website: http://uk.giga-byte.com The Netherlands Giga-Byte Technology B.V. Address: Verdunplein 8 5627 SZ, Eindhoven, The Netherlands Tel: +31 40 290 2088 NL Tech.Support : 0900-GIGABYTE (0900-44422983, 0.2/M) BE Tech.Support : 0900-84034 ( 0.4/M) Fax: +31 40 290 2089 Tech. Support: http://nz.giga-byte.com/TechSupport/ServiceCenter.htm Non-Tech. Support (Sales/Marketing issues): http://ggts.gigabyte.com.tw/nontech.asp Website: http://www.giga-byte.nl China NINGBO G.B.T. Tech. Trading CO., Ltd. Tech. Support: http://cn.giga-byte.com/TechSupport/ServiceCenter.htm Non-Tech. Support (Sales/Marketing issues): http://ggts.gigabyte.com.tw/nontech.asp Website: http://www.gigabyte.com.cn Beijing Tel: 86-10-82856054, 86-10-82856064, 86-10-82856094 Fax: 86-10-82856575 Chengdu Tel: 86-28-85236930 Fax: 86-28-85256822 GuangZhou Tel: 86-20-87586273 Fax: 86-20-87544306 Shanghai Tel: 86-21-64737410 Fax: 86-21-64453227 Shenyang Tel: 86-24-23960918, 86-24-23960893 Wuhan Tel: 86-27-87854385, 86-27-87854802 Fax: 86-27-87854031 Xian Tel: 86-29-5531943 Fax: 86-29-5539821
- 40 -