You are on page 1of 36

Pumpen

T.I.P .

The Pump Pros

Submersible pumps Garden pumps Submersible pressure pumps Deep-well pumps Booster sets Petrol-engine pumps Special pumps
www.tip-pumpen.de

T.I.P.

TECHNIK + KOMPETENZ

Dear customer,
we are pleased to present you our new catalogue on pump and irrigation technology. This new edition, too, contains all you have to know including useful tips around the topics of drainage and irrigation as well as domestic water supply. Our comprehensive product range and our more than 30 years of experience in the development of high-quality pumps will permit you to find the product tailored to your specific needs. In our specialised separate catalogue you will find a large selection of products around your pond.

More than 30 years of development of top-level pumps

Our company, specialised in the manufacture and distribution of water pumps and pond filters, was founded in 1978. When selecting the product range, quality had absolute priority from the onset. The excellent price/performance ratio of our products quickly yielded positive results. In Germany, for instance, T.I.P. has been counting for years among the leading suppliers of pumps for private use in the house, yard and garden. Meanwhile, we are also very successful in distributing our products on a Europe-wide basis and in some non-European countries.

Continuous further development guarantees high quality

The success and high quality of our range of products are owing to the incessant further development of our products in line with the latest state in technological expertise. This is escorted by a consistent implementation of top-quality requirements in the selection of the materials and in the planning of production flows. This approach has resulted in convincing, powerful high-quality pumps with a low energy consumption. Moreover, our focus in the development of products is on a rigorously responsible use of water as a resource which becomes more and more scarce and valuable. Saving water and the sensible use of grey, brown and rainwater instead of drinking water will not only decrease your household costs, it also means an active contribution to environmental protection. The safety topic, too, plays a major role in the development of our products. This means, for instance, that all our pumps bear the GS mark (Geprfte Sicherheit = Tested for safety).

T.I.P. with a customer-friendly service offer on the internet

At www.tip-pumpen.de you will find a comprehensive and neatly organised internet presence where the main focus is on the benefit for our customers. Detailed information about products and accessories will permit you to take a deep insight in our product range. Moreover, informational product sheets are ready for being printed out. Any required spare parts can be selected and ordered quickly in our online shop. Within a regular updating process, we introduce new products, describe innovative technologies and publish valuable tips so that dropping by at our internet presence is always worthwhile.

Service hotline to clarify technical questions

As a special service, we offer you a hotline regarding technical questions. Our specialised staff are ready to advise you in questions regarding installation, maintenance or similar matters. You can reach our technicians Monday through Friday from 15.00 to 17.00 oclock on 0049-(0)7263-912582 and 0049-(0)7263-912583. Please note: This service hotline is not in charge of matters regarding spare parts and repair, these are under the responsibility of a separate department.

Spare parts with 10 years availability guaranteed

Our products come up to high standards in terms of quality and reliability. Nevertheless, they are subject to natural wear and tear which entails the necessity for spare parts. In this regard we may proudly mention our quite unusual offer which is highly appreciated by our customers: We guarantee 10 years of availability for our spare parts. You wont have any problems finding spare parts for any products up to an age of 10 years, calculated from the day of the products purchase. If any repair work or spare parts should become necessary, please contact us by post, fax or e-mail. The corresponding addresses can be found on page 35. Our internet presence at www.tip-pumpen.de offers you the fastest and most convenient way of ordering spare parts. In the spareparts shop you will find explosion drawings and part lists of our products so that it takes just a few clicks to locate and order any part you may need. We wish you a lot of fun and inspiration when browsing through our catalogue.

Your T.I.P. Technische Industrie Produkte GmbH

The Pump Pros


www.tip-pumpen.de
2

Inhalt
Pumpen
T.I.P .

We have the solution for you!


Drainage
Submersible clean-water pumps Submersible drainage pumps Submersible dirty-water pumps Contractors dirty-water pumps P. 4-9

Irrigation
Rain-water pump Submersible pressure pumps Deep-well pumps Garden pumps Automatic booster sets Automation

P. 10 - 19

Automatic water supply


Booster sets Booster set with 50 L pressure vessel Booster set for deep intake P. 20 - 27

Special pumps
Petrol-engine driven water pumps Peripheral pump P. 28 - 30

Accessories
for submersible pumps for surface pumps P. 31 - 34

Contact
Contact P. 35

www.tip-pumpen.de
3

T.I.P.

TECHNIK + KOMPETENZ

Drainage

Submersible clean-water pumps


For clear and moderately contaminated water Drainage, fluid transfer, evacuation Special designs for narrow drainage shafts Units with shallow-suction capability for drainage down to surfaces ready to be wiped off Float switch for automatic operation Maintenance-free motor with thermal overload protection Pump housing made of impact-resistant plastic Variable connection sizes owing to multi-dimensional connection piece

Submersible clean-water pumps are suitable for pumping down or transferring pure or moderately contaminated liquids. Typical applications include the discharge of household waste water, rain or seepage water as well as the evacuation of basins. One of the very particular features of submersible clean-water pumps is their shallow-suction capability which leaves surfaces ready to be wiped off. A pressure as low as 0.5 bar will be sufficient for the operation of a garden shower.

Submersible drainage pumps are especially designed for use in narrow drainage shafts owing to their compact design, the vertical pump outlet and the suspension cable. This type of pump is equipped with an integrated float switch which gives you the choice between automatic or manual operation.

Shallow-suction units enable drainage down to surfaces ready for being wiped off since evacuation is possible down to a particularly low water level of just a few millimetres. The technical details of the pumps always specify the minimum evacuation level. This value indicates the lowest water level possible down to which liquids can be pumped off.

ON
AUTO ON

Proven technology

Pump housing depending on the design, made of plastic, high-grade steel or cast metal Float switch - automatic cut-in/cut-out as a function of the water level Motor - protected from overload by a thermoprotector Mains cable - 10 metres

F OF
AUTO OFF

The float switch fulfils two important functions: On the one side, it will cut the pump in or out as a function of the water level, thus enabling the pump to be operated automatically. On the other, it protects the pump from damage caused by overheating resulting from operation in the absence of water, since it will cause the pump to cut out as soon as a specific fluid level is fallen short of.

Pump impeller - low-wearing design with a long life cycle Horizontal pump outlet - large dimension to ensure unrestricted passage of liquid

www.tip-pumpen.de
4

Submersible pumps

TECHNIK + KOMPETENZ

T.I.P.

The product range - conventional and special designs

Submersible drainage pump

Submersible clean-water pump

Submersible clean-water pump

Submersible clean-water pump

INTEGRA 440 FS

TKV 8000

TKX 8000

TKX 12000

Special design with shallow- Special design with shallow- Very reliable starter unit in Powerful, highly efficient unit suction capability for narrow suction capability for narrow conventional design in conventional design shafts from 20 cm shafts, wells etc. Optimally suited for all typical Optimally suited for all typical Vertical pump outlet Vertical pump outlet tasks of submersible clear tasks of submersible clear Integrated float switch water pumps water pumps Comes with a lowering rope

Max. flow rate Max. delivery height / pressure Nominal performance Max. submersion depth Pressure port Min. evacuation level Max. grain size Item number

8.500 l/h 7 m / 0,7 bar 300 Watt 5m 41,91 mm (1 1/4 MT) 3 mm 5 mm 30112

7.800 l/h 6 m / 0,6 bar 300 Watt 5m 41,91 mm (1 1/4 MT) 10 mm 5 mm 30250

7.800 l/h 6 m / 0,6 bar 300 Watt 7m 41,91 mm (1 1/4 MT) 20 mm 6 mm 30251

12.000 l/h 7 m / 0,7 bar 400 Watt 7m 41,91 mm (1 1/4 MT) 20 mm 6 mm 30252

Flow rate depending on the discharge height

7,0 m 6,0 m 5,0 m 4,0 m 3,0 m 2,0 m 1,0 m

950 l/h 2.500 l/h 3.900 l/h 4.950 l/h 6.200 l/h 7.300 l/h

6,0 m 5,0 m 4,0 m 3,0 m 2,0 m 1,0 m

2.580 l/h 3.660 l/h 4.500 l/h 5.700 l/h 6.780 l/h

6,0 m 5,0 m 4,0 m 3,0 m 2,0 m 1,0 m

1.500 l/h 2.800 l/h 4.500 l/h 6.000 l/h 7.100 l/h

7,0 m 6,0 m 5,0 m 4,0 m 3,0 m 2,0 m 1,0 m

1.650 l/h 3.300 l/h 5.000 l/h 7.600 l/h 9.600 l/h 11.000 l/h

www.tip-pumpen.de
5

T.I.P.

TECHNIK + KOMPETENZ

Drainage

Submersible dirty-water pumps


For clear and heavily contaminated water Drainage, fluid transfer, evacuation, emergency drainage Special designs for continuous operation and hot liquids Extraordinarily solid and efficient contractors pumps Float switch for automatic operation Maintenance-free motor with thermal overload protection Pump housing made of plastic, cast iron or high-grade steel Male thread for unrestricted flow rate All units are equipped with connection pieces

Submersible dirty-water pumps were developed for draining or transferring heavily contaminated liquids. These units will take in and convey leaves and other plant residues, coarse particles and fibrous matters without any problems. Therefore, they are optimally suited for draining garden ponds, pools, constructionsites and dirty-water pits.

With regard to emergency drainage of flooded premises, submersible dirty-water pumps are indispensable for rapid pumping off to minimise water damage. In these cases, the water mostly contains coarse particles. The max. grain size referred to in the technical data specifies the max. diameter of the contaminating elements which the liquid being discharged is allowed to contain.

With its particularly high-quality technology, the EXTREMA 300/10 is an absolute top-class pump. The housing which is completely made of high-grade steel, the water-cooled motor and the high-precision ball bearings allow a performance level complying with very high standards. As a particular feature, it is possible to pump somewhat hot liquids up to 50 C temporarily even up to 95 C. Submersible dirty-water pumps are used to carry water which contains contaminants of various sizes. However, floating particles, sludge, sand, leaves, other plant residues and similar particles may interfere with the pumps proper operation or even stop it. The VORTEX free-flow wheel efficiently prevents clogging of the pump since it swirls and shreds the contaminants to make them pass freely through the hydraulic system. This technology has proven in practice for years in the evacuation of ponds and construction pits, but also for emergency drainage when everything has to be done very fast, although larger particles may be contained in the water and the pumps have to work at a maximum degree of efficiency and reliability.

The VORTEX free-flow wheel

The great variety of applications of submersible dirty-water pumps is reflected in a carefully balanced range of products. This means, for instance, that the TVX series includes conventional designs for all common applications. In addition thereto, the DTX series is suitable for continuous operation. The top-quality Maxima series was developed for areas of use requiring extraordinarily strong, durable material.

www.tip-pumpen.de
6

Submersible pumps

TECHNIK + KOMPETENZ

T.I.P.

The TVX series - classic designs for each class of performance

Submersible dirty-water pump

Submersible dirty-water pump

Submersible dirty-water pump

Support system (multifunctional)

TVX 8000

TVX 12000

TVX 15000

TPT 20

Max. flow rate Max. delivery height / pressure Nominal performance Max. submersion depth Pressure port Min. evacuation level Max. grain size Item number

Ideal, very reliable starter unit Powerful, highly efficient Particularly powerful, highly Versatile support system for all submersible pumps, in conventional design unit in conventional design efficient unit in conventional submersible pressure and Optimally suited for all typical Optimally suited for all typical design tasks of submersible dirtytasks of submersible dirty For speedy drainage of water deep-well pumps Increased installation verwater pumps water pumps containing exceptionally satility owing to horizontal or coarse contamination upright positioning of the 7.800 l/h 10.800 l/h 14.200 l/h pump Increased stability and 5 m / 0,5 bar 6 m / 0,6 bar 8 m / 0,8 bar functional safety of the pump 320 Watt by installing the support 480 Watt 600 Watt system to the edges of 7m 7m 7m cisterns or wells When used as a wall support, 41,91 mm (1 1/4 MT) 41,91 mm (1 1/4MT) 41,91 mm (1 1/4 MT) the device is ideally suited as 30 mm 30 mm 37 mm a storage place for the pump e.g. in periods of frost 20 mm 20 mm 35 mm

30260

30261

30270

30947

7,0 m 5,0 m 4,0 m 3,0 m 2,0 m 1,0 m 6,0 m 5,0 m 4,0 m 3,0 m 2,0 m 1,0 m 2.000 l/h 4.300 l/h 6.500 l/h 8.300 l/h 10.500 l/h 6,0 m 5,0 m 4,0 m 3,0 m 2,0 m 1,0 m

1.800 l/h 4.200 l/h 6.000 l/h 8.200 l/h 10.000 l/h 11.300 l/h 13.200 l/h

1.600 l/h 3.400 l/h 5.000 l/h 6.500 l/h

www.tip-pumpen.de
7

Application example

Flow rate depending on the discharge height

8,0 m

T.I.P.

TECHNIK + KOMPETENZ

Drainage

Submersible dirty-water pumps


The DTX series: Submersible dirty-water pumps for continuous operation
Special units for uninterrupted operation optimally suited for both the typical application areas of submersible dirty-water pumps and for the recirculation of pond water and the operation of water courses Low-wearing design and silent operation owing to ceramics-coated high-grade steel motor shaft The VORTEX free-flow wheel minimises the risk of clogging and increases functional reliability Thermal overload protection will cut out the pump in the presence of any risk of overheating Float switch providing both automated cut-in and cut-out and an efficient protection from operation in the absence of water

Submersible dirty-water pump

Submersible dirty-water pump

Submersible dirty-water pump

Submersible dirty-water pump

DTX 7500
Solid starter unit Suited for continuous operation - for instance for the recirculation of water or the operation of water courses

DTX 7500 T

DTX 10000

EXTREMA 300/10
Extremely powerful unit All high-grade steel design Water-cooled motor High-precision ball bearings Suitable for use with hot liquids up to 50 C, temporarily even up to 95 C

Solid starter unit, comes Powerful, highly efficient unit with a support system for Suited for continuous horizontal installation and a operation - for instance for protection grid to prevent the recirculation of water or fish from being taken in the operation of water Suited for continuous operation courses

Max. flow rate Max. delivery height / pressure Nominal performance Max. submersion depth Pressure port Min. evacuation level Max. grain size Item number

7.500 l/h 6 m / 0,6 bar 320 Watt 7m 41,91 mm (1 1/4 MT) 25 mm 22 mm 30157

7.500 l/h 6 m / 0,6 bar 320 Watt 7m 41,91 mm (1 1/4 MT) 25 mm 22 mm 30258

9.000 l/h 6 m / 0,6 bar 480 Watt 7m 41,91 mm (1 1/4 MT) 25 mm 22 mm 30158

18.000 l/h 10 m / 1,0 bar 1.100 Watt 5m 47,80 mm (1 1/2 MT) 45 mm 40 mm 30038
10,0 m 9,0 m 8,0 m 7,0 m 6,0 m 5,0 m 4,0 m 3,0 m 2,0 m 1,0 m

Flow rate depending on the discharge height


6,0 m 5,0 m 4,0 m 3,0 m 2,0 m 1,0 m 2.000 l/h 3.000 l/h 5.000 l/h 6.000 l/h 7.200 l/h 6,0 m 5,0 m 4,0 m 3,0 m 2,0 m 1,0 m 2.000 l/h 3.000 l/h 5.000 l/h 6.000 l/h 7.200 l/h 6,0 m 5,0 m 4,0 m 3,0 m 2,0 m 1,0 m 2.200 l/h 3.500 l/h 5.400 l/h 6.800 l/h 8.100 l/h

1.500 l/h 3.000 l/h 4.300 l/h 6.600 l/h 8.600 l/h 10.500 l/h 12.800 l/h 14.400 l/h 16.500 l/h

www.tip-pumpen.de
8

Submersible pumps

TECHNIK + KOMPETENZ

T.I.P.

The Maxima series - units for use in extreme conditions


Maxima 400 SX: Absolute top-class contractors pump
Especially designed, particularly solid and strong submersible dirty-water pump for use under very extreme conditions Optimally suited for all typical areas of use of submersible dirty-water pumps as well as for draining construction-sites and dirty-water pits and sewage water handling Hydraulic housing and impeller made of highly resistant cast iron, pump housing made of highgrade steel and cast iron Outstanding performance with extraordinary discharge volume, pump head and max. grain size Equipped with a VORTEX free-flow wheel, thermal overload protection and a float switch
The Maxima 400 SX will carry out its duty even under the toughest load. (German do-it-your-self magazine Praxis, edition March/April 2010)

Submersible dirty-water pump

Submersible dirty-water pump

Submersible dirty-water pump

Submersible dirty-water pump

Maxima 180 SX
Versatile entry unit to the Maxima top-class series High-grade steel pump housing Very sturdy pump

Maxima 250 SX
Powerful and efficient unit High-grade steel pump housing Very sturdy pump With 2 connection pieces

Maxima 300 SX
Very powerful and efficient unit All high-grade steel design Very sturdy pump With 2 connection pieces

Maxima 400 SX
Especially designed contractors pump Pump housing in high-grade steel and cast iron For use under particularly extreme conditions With 2 connection pieces

Max. flow rate Max. delivery height / pressure Nominal performance Max. submersion depth Pressure port Min. evacuation level Max. grain size Item number

10.500 l/h 7 m / 0,7 bar 500 Watt 5m 41,91 mm (1 1/4 MT) 37 mm 25 mm 30121

14.500 l/h 8 m / 0,8 bar 600 Watt 5m 41,91 mm (1 1/4 MT) 37 mm 25 mm 30264

18.000 l/h 8 m / 0,8 bar 700 Watt 5m 47,80 mm (1 1/2 MT) 40 mm 30 mm 30116

24.000 l/h 9 m / 0,9 bar 950 Watt 5m 45,48 mm (1 1/2 FT) 40 mm 35 mm 30140

Flow rate depending on the discharge height

7,0 m 6,0 m 5,0 m 4,0 m 3,0 m 2,0 m 1,0 m

1.900 l/h 3.900 l/h 4.600 l/h 6.000 l/h 7.400 l/h 8.800 l/h

8,0 m 7,0 m 6,0 m 5,0 m 4,0 m 3,0 m 2,0 m 1,0 m

3.300 l/h 5.550 l/h 7.160 l/h 8.750 l/h 10.200 l/h 11.650 l/h 13.050 l/h

8,0 m 7,0 m 6,0 m 5,0 m 4,0 m 3,0 m 2,0 m 1,0 m

3.000 l/h 6.000 l/h 8.500 l/h 11.200 l/h 13.500 l/h 16.000 l/h 17.500 l/h

9,0 m 8,0 m 7,0 m 6,0 m 5,0 m 4,0 m 3,0 m 2,0 m 1,0 m

1.800 l/h 4.800 l/h 7.800 l/h 10.800 l/h 13.500 l/h 15.600 l/h 18.100 l/h 20.700 l/h

www.tip-pumpen.de
9

T.I.P.

TECHNIK + KOMPETENZ

Irrigation

Submersible pressure pumps / Rain-water pumps


For discharging water from great depth The liquid will be conveyed on under high pressure Water supply and watering from wells and storage reservoirs Special units for rain drums and narrow shafts Pump housing made of impact-resistant plastic, sturdy cast aluminium or top-grade steel

Submersible pressure pumps are very powerful pumps of a specific design, meant to draw water from very deep down. The fluid lifted in this way can be transported further under a high pressure and thus be used e.g. for an irrigation system or for domestic purposes. In addition, these pumps are perfectly suited for direct irrigation out of wells, cisterns and reservoirs.

The Brio 2000-M control system enables the operation of submersible pressure pumps to be automated. In this way it is possible to use pumps for automatic water supply. This means that the liquids being discharged can be used as if tapped from the water mains. And all this with a useful side effect: The control system will also protect the pumps from damage causes by dry-running since they will stop operation in the absence of water.

The PPG 225 diaphragm pump is a submersible pressure pump which was developed especially for use in narrow shafts. With its vertical pump outlet and the enclosed lowering rope this particularly compact and efficient pump is suitable for use in openings down to a diameter of 11 cm. The reliable motor with a nominal performance of 225 W insures a delightfully low energy consumption.

Rain-water pump DIO 45/13


Continuously adjustable flow rate Three riser pipe elements for height adjustment Special clamp for fastening to the container edge Vertical pump outlet Float switch for automated cutting-in and cutting-out

The DIO 45/13 rain-water pump is the unit of choice when it comes to conveniently filling watering cans or operating connected watering shower heads with water taken from rain barrels or similar containers. A special clamp ensures the firm grip at the container edge, with three riser-pipe elements enabling the submersion depth to be adjusted. The float switch provides an efficient protection from dry-running.

www.tip-pumpen.de
10

Submersible pressure pumps / Rain-water pumps

TECHNIK + KOMPETENZ

T.I.P.

Submersible pressure pumps / Rain-water pumps


DRAIN 6000/36: Highly efficient submersible pressure pump
Submersible pressure pump in top-grade design with powerful, multistage pump mechanism for discharging water from great depth Pump housing and motor shaft made of topgrade steel Suitable for both mobile use or stationary installation The automated operation of the unit using the optionally available control system enables the water being discharged to be used conveniently as though it came tapped from the water mains

Rain-water pump

Submersible pressure pump

Submersible pressure pump

Support system (multifunctional)

DIO 45/13

DRAIN 6000/36

PPG 225

TPT 20

Max. flow rate Max. delivery height / pressure Nominal performance Max. submersion depth Pressure port Well diameter min. Max. grain size Item number

Continuously adjustable Very powerful pump with a Energy-saving diaphragm Versatile support system for pump for emptying containers high discharge capacity pump for narrow shafts all submersible pumps, Convenient filling of watering Pump housing and motor Pump housing made of sturdy submersible pressure and deep-well pumps cans and operation of shaft made of high-grade steel die-cast aluminium watering shower heads For discharging water from For discharging water from Increased installation versatility owing to horizontal or great depth Easy to install great depth upright positioning of the 2.700 l/h 6.000 l/h 1.080 l/h pump Increased stability and 13 m / 1,3 bar 34 m / 3,4 bar 50 m / 5,0 bar functional safety of the pump by installing the support 350 Watt 950 Watt 225 Watt system to the edges of 5m 7m 5m cisterns or wells 26,44 mm (3/4 MT) 41,91 mm (1 1/4 MT) 17 mm, with out thread When used as a wall support, the device is ideally suited as 500 mm 110 mm a storage place for the pump e.g. in periods of frost 2 mm 2 mm P 2 mm

30263

30136

56000
50,0 m 45,0 m 40,0 m 30,0 m 25,0 m 20,0 m 15,0 m 10,0 m 5,0 m 1,0 m

30947
Application example

Flow rate depending on the discharge height

13,0 m 9,0 m 6,0 m 5,0 m 4,0 m 3,0 m 2,0 m 1,0 m

800 l/h 1.810 l/h 1.950 l/h 2.120 l/h 2.360 l/h 2.500 l/h 2.600 l/h

34,0 m 30,0 m 25,0 m 20,0 m 15,0 m 10,0 m 5,0 m 1,0 m

1.100 l/h 2.600 l/h 3.800 l/h 4.500 l/h 5.200 l/h 5.800 l/h 5.950 l/h

220 l/h 400 l/h 600 l/h 760 l/h 820 l/h 900 l/h 990 l/h 1.020 l/h 1.060 l/h

Number of sprinklers
2x 1x

www.tip-pumpen.de
11

T.I.P.

TECHNIK + KOMPETENZ

Irrigation

Deep-well pumps / Cistern pumps


Particularly high-quality workmanship, technology and design For discharging water from very great depth The liquid will be conveyed on under high pressure For use in wells, cisterns, shafts For particularly narrow borehole wells from 10 cm Optimally suited for automated water supply when used with special accessory for automation All units come with a particularly long connection cable

Deep-well pumps are specifically developed and most efficient submersible pressure pumps for use in particularly narrow shafts and in wells, cisterns and similar cavities. To facilitate the discharge of water from very deep down, the standard scope of delivery includes a long connection cable and a special rope for lowering and positioning the pumps.

Deep-well pumps excel by their outstanding technical properties, the use of top-class materials and a very high performance. Owing to their particular design, they can be used in very narrow borehole wells with diameters down to 10 cm. Their most reliable operation is guaranteed by a multistage hydraulic system and an integrated check (or non-return) valve.

The multistage hydraulic system of the deepwell pumps of the AJ 4 Plus series is equipped with floating impellers which have proven to be particularly resistant to the corrosive effect of sand up to a contents of 50 g/m. The compressed-ceramics ring in the diffuser and the graphite ring ensure a high durability in the case of operation in the absence of water.

Cistern pump EJ 6 Plus

Very powerful and particularly high-quality special design in all top-grade steel design for use in cisterns - apart from that comes optimally suited for discharging water from wells and shafts For a versatile use of grey water - such as garden watering or the operation of irrigation systems Multistage hydraulic system with closed radial impellers made of Noryl

All deep-well pumps from T.I.P. are capable of building up a pressure of 1.5 bar which is the minimum pressure required for automation. When installing the optional Brio 2000-M electronic controlling system which is needed for automation, the water being discharged can be used just as conveniently as if it was taken from the water mains, and moreover this feature provides an additional protection from damage caused by operation in the absence of water.

High degree of stableness and secure positioning owing to a very solid support foot Comprehensive standard equipment: Solid lowering rope, high-grade suction hose made of foodproof material, intake filter with check/non-return valve, highly effective float for cistern pumps (its buoyant force insures a sufficient distance between the end of the suction line and the bottom, thus preventing particles at the bottom from being sucked in)

www.tip-pumpen.de
12

Deep-well pumps / Cistern pumps

TECHNIK + KOMPETENZ

T.I.P.

Deep-well pumps / Cistern pumps

Deep-well pump

Deep-well pump

Deep-well pump

Cistern pump

AJ 4 Plus 55/50

AJ 4 Plus 100/36

AJ 4 Plus 100/57

EJ 6 Plus

For discharging water from For discharging water from very deep down great depth Pressure-intensive applications Very large discharge High-grade steel pump volume housing High-grade steel pump housing

Very powerful unit High-quality special deve For discharging water from lopment in all high-grade steel very deep down design for use in cisterns and Pressure-intensive applications wells Very large discharge volume For discharging water from High-grade steel pump housing very deep down

Max. flow rate Max. delivery height / pressure Nominal performance Max. submersion depth Pressure port Well diameter min. Max. grain size / sand Item number

3.300 l/h 50 m / 5,0 bar 800 Watt 20 m 39,59 mm (1 1/4 FT) 100 mm
P 2 mm / 50 g/m3

6.000 l/h 36 m / 3,6 bar 750 Watt 20 m 39,59 mm (1 1/4 FT) 100 mm
P 2 mm / 50 g/m3

6.000 l/h 57 m / 5,7 bar 1.100 Watt 20 m 39,59 mm (1 1/4 FT) 100 mm
P 2 mm / 50 g/m3

6.000 l/h 55 m / 5,5 bar 1.400 Watt 20 m 30,93 mm (1 FT) 350 mm 0 mm 30156
55,0 m 45,0 m 40,0 m 35,0 m 30,0 m 25,0 m 20,0 m 15,0 m 10,0 m 5,0 m

30104
50,0 m 45,0 m 40,0 m 35,0 m 30,0 m 25,0 m 20,0 m 15,0 m 10,0 m 5,0 m

30155

30086
57,0 m 45,0 m 40,0 m 35,0 m 30,0 m 25,0 m 20,0 m 15,0 m 10,0 m 5,0 m

Flow rate depending on the discharge height

Number of sprinklers

450 l/h 950 l/h 1.400 l/h 1.750 l/h 1.900 l/h 2.100 l/h 2.300 l/h 2.600 l/h 2.950 l/h

36,0 m 30,0 m 25,0 m 20,0 m 15,0 m 10,0 m 5,0 m

2.700 l/h 3.600 l/h 4.100 l/h 4.650 l/h 5.150 l/h 5.550 l/h

2.150 l/h 2.950 l/h 3.550 l/h 3.950 l/h 4.150 l/h 4.650 l/h 4.950 l/h 5.300 l/h 5.650 l/h

1.700 l/h 2.600 l/h 3.400 l/h 3.950 l/h 4.400 l/h 4.800 l/h 5.100 l/h 5.450 l/h 5.700 l/h

3x

4x

6x

6x

www.tip-pumpen.de
13

T.I.P.

TECHNIK + KOMPETENZ

Irrigation

Garden pumps
Water withdrawal from reservoirs, welds, watercourses Filling and emptying of ponds, basins, storage reservoirs Watering and operation of irrigation systems Suitable for mobile use or stationary installations is Maintenance-free motor with thermal overload protection Pump housing made of plastic, cast iron or high-grade steel All units are suitable for automation

Garden pumps are versatile pumps for mobile use or stationary installation. They are ideally suited for pumping water out of wells, watercourses or cisterns, for instance to irrigate your garden. Their range of application also includes the filling or emptying of ponds, basins or reservoir tanks. All units are equipped with a thermal motor protection.

The use of garden pumps enables the water being withdrawn to be conveyed on under high pressure. This means that these units are very well suitable for operating watering systems most of the units can even be used with multiple sprinklers. Moreover, the typical areas of use of garden pumps include other pressureintensive purposes, such as the efficient flushing of terraces or boardwalks.

A suction hose of 4 metres length with check valve comes with some of our garden pumps as a convenient element of the standard scope of delivery. In addition, we offer you suction hoses of various lengths and quality grades from solid plastic types up to professional suction fitting sets in high-quality design with a very high operating-pressure rating. For the range of products offered, please refer to page 31.

Suction height of all surface pumps: 9 m max.

Suction height: Pump head:

Height difference between the water surface and the pump. Height difference between the water surface and the point of water withdrawal. The max. delivery height is referred to as pump head. Example: If a pump takes in water in 5 m depth to lift it 15 m upwards, the pump head totals 20 m.

Maximum number of sprinklers


Garden pumps are self-priming units. This means that it is recommendable, yet not absolutely necessary, to fill the suction hose with water prior to the first use of the unit, since the pump will take in liquid independently. In this process, however, the pump housing must be completely filled, i.e. vented. This means that the procedure has to be repeated so many times until the suction hose, too, is fully vented. The max. number of sprinklers stated for pressure pumps, garden pumps and other surface pumps are subject to the following conditions: Water flow rate at the sprinkler: approx. 600 l/h Water pressure at the sprinkler: approx. 2 bar Suction height: 5 m max.

www.tip-pumpen.de
14

Garden pumps

TECHNIK + KOMPETENZ

T.I.P.

Garden pumps
The Garten-Jet series: Smooth-running units with robust pump housing

Owing to their cast-iron pump housing, the units of the Garten-Jet series excel by their particular robustness and smooth running operation. The Garten-Jet 750, which completes all tasks of garden pumps in a highly reliable manner and with a comparably low energy consumption, is the ideal starter model in compact design. The Garten-Jet 1200 with its high efficiency degree also permits large-area watering and applications in the agricultural range.

Garden pump

Garden pump

Garden pump

GPK 46/42

Garten-Jet 750

Garten-Jet 1200

Reliable starter unit with pump housing Smooth-running starter unit with pump Smooth-running, very powerful starter made of impact-resistant plastic housing made of solid cast iron unit with housing made of solid cast iron Low weight Very solid and reliable unit Suitable for continuous operation Suitable for all areas of use of garden Suitable for all areas of use of garden Also very well suited for the agricultural pumps pumps sector, for instance for large-area watering

Max. flow rate Max. delivery height / pressure Nominal performance Pressure port Suction port Pump housing Cross weight Item number

2.800 l/h 42 m / 4,2 bar 550 Watt 33,25 mm (1 MT) 33,25 mm (1 MT) Plastic 6,2 kg 30124

2.800 l/h 42 m / 4,2 bar 600 Watt 30,93 mm (1 FT) 30,93 mm (1 FT) Cast iron 8,6 kg 31175

4.300 l/h 50 m / 5,0 bar 1.200 Watt 30,93 mm (1 FT) 30,93 mm (1 FT) Cast iron 16,4 kg 31174

Flow rate depending on the discharge height

50 m 42 m 40 m 30 m 20 m 10 m 150 l/h 700 l/h 1.850 l/h 2.500 l/h 42 m 40 m 30 m 20 m 10 m 150 l/h 600 l/h 1.500 l/h 2.400 l/h 45 m 40 m 30 m 20 m 10 m 800 l/h 1.700 l/h 2.650 l/h 3.600 l/h 4.100 l/h

Number of sprinklers
1x 1x 5x

www.tip-pumpen.de
15

T.I.P.

TECHNIK + KOMPETENZ

Irrigation / Garden pumps

Garden pumps
Clean Jet 1600 Plus: Garden pump meeting highest demands
Very powerful garden pump in high-quality workmanship Pump housing made of highgrade steel Maintenance-free capacitor motor with thermal overload protection Particularly large suction port A solid metal plate provides for a solid standing and ease of installation in the case of stationary use

Garden pump

Garden pump

Garden pump

Garden pump

GP 3000 INOX
Ideal starter unit to the product series equipped with high-grade steel pump housing Suitable for all areas of use of garden pumps

GP 4500 INOX/Kit
High-grade steel pump housing Top-class unit Comes with a suction hose (4 m) with inlet filter and check (non-return) valve

Clean Jet 1000 Plus/Kit


High-grade steel pump housing Superior unit Comes with a suction hose (4 m) with inlet filter and check (non-return) valve Solid metal plate included

Clean Jet 1600 Plus


Absolute top-class unit with a very high performance High-grade steel pump housing Solid metal plate included

Max. flow rate Max. delivery height / pressure Nominal performance Pressure port Suction port Pump housing Cross weight Item number

2.950 l/h 42 m / 4,2 bar 550 Watt 30,93 mm (1 FT) 30,93 mm (1 FT) High-grade steel 6,3 kg 30111

4.350 l/h 50 m / 5,0 bar 1.200 Watt 30,93 mm (1 FT) 30,93 mm (1 FT) High-grade steel 11,4 kg 30106

3.300 l/h 46 m / 4,6 bar 800 Watt 30,93 mm (1 FT) 30,93 mm (1 FT) High-grade steel 8,9 kg 30094

5.400 l/h 50 m / 5,0 bar 1.600 Watt 30,93 mm (1 FT) 41,91 mm (1 1/4 MT) High-grade steel 13,0 kg 30159

Flow rate depending on the discharge height

50 m 42 m 40 m 30 m 20 m 10 m 150 l/h 600 l/h 1.500 l/h 2.400 l/h 42 m 40 m 30 m 20 m 10 m 800 l/h 1.400 l/h 2.700 l/h 3.500 l/h 3.900 l/h

46 m 42 m 40 m 30 m 20 m 10 m 400 l/h 460 l/h 1.200 l/h 2.550 l/h 3.200 l/h

50 m 42 m 40 m 30 m 20 m 10 m 1.000 l/h 1.500 l/h 3.200 l/h 5.000 l/h 5.100 l/h

Number of sprinklers
2x 5x 2x 6x

www.tip-pumpen.de
16

Irrigation / General information

TECHNIK + KOMPETENZ

T.I.P.

Installation and maintenance


Garden pumps, booster sets and automatic booster sets from T.I.P. are self-priming units. This means that it is not strictly necessary to fill the suction line, since the pump will take in liquid independently. However, it has to be ensured that the pump housing is completely filled, i.e. fully vented. Depending on the suction height of the water, this process may have to be repeated several times until the suction line, too, is fully vented. This means that filling the suction line may nevertheless be recommendable. In any case, the inlet of the suction line has to be equipped with a check valve with an intake filter to prevent the water from escaping and coarse particles from being sucked in. Once the line and pump vented, the system will work as desired. During operation, any inadvertent venting of the system through leaks or the like must be excluded under all circumstances. This means that all threaded and other connections on both the suction and the pressure side have to be absolutely tight. Perfect tightening results can be obtained by using Teflon tape, hemp or a similar material.

MIN

10 x (ca. 1 m)

Installation of submersible pressure pumps and deep-well pumps


To lower submersible pressure pumps and deep-well pumps down into cisterns, wells etc., one should always use the lowering rope coming with the unit or another suitable cable made of stainless steel or nylon. The lowering rope, the connection cable and the pressure line should be tied together at intervals of approx. 2 m using an appropriate adhesive tape or cable ties to make sure that they will not get entangled when lowering or raising the pump. The pump has to be located at least 50 cm above the ground to prevent bottom particles from being sucked in, since they may block or even damage the unit. Please observe the max. water immersion depth which is indicated in the technical data of the pump. During operation, the intake port must always remain immersed in the water, since otherwise damage caused by overheating may occur. With regard to positioning the pump this means that you should take into account fluctuations of the water level during operation, for instance as a result of the withdrawal of liquid or seasonal changes. Some units - such as the entire AJ 4 Plus series - come with a standard check valve.

Maintenance
Regular maintenance and thorough care will reduce the risk of operational disturbances and extend the lifetime of pumps. Where necessary, it is recommendable for submersible pumps to clean the hydraulic parts by way of counter-flushing the unit with clear water through the pressure port. To facilitate the removal of stubborn dirt, the pump foot can be dismantled. In the case of booster sets, a regular check of the pressure being generated and the energy being consumed makes sense. Also, the pre-charge pressure (atmospheric pressure) in the pressure tank, which must not fall below 1.5 bar, should be checked regularly through the tank valve. The intake filter of the deep-well pumps of the AJ 4 Plus series, which can be unscrewed from the unit for this purpose, should be cleaned on a regular basis. In frosty conditions, submersible pumps have to be removed from the water, and in this case basically all pumps including their pipe system should be drained.

Capacity of pumps under various conditions


50 m 42 m 40 m 30 m 20 m 10 m 1.000 l/h 1.500 l/h 3.200 l/h 5.000 l/h 5.100 l/h
When selecting a suitable pump, the desired flow rate and the required suction height - i.e. the height difference between the water surface and the point of the water withdrawal - count among the major criteria. Therefore, the information provided for all pumps includes the maximum flow rate and the maximum suction height. When planning an installation or selecting a pump, please consider that the flow rate will drop with the increase of the suction height. Diagrams given with the pumps are intended to illustrate this relationship, and they also provide the applicable values for different conditions. Similar considerations apply to the max. achievable pressure which will also decrease with an increase of the suction height.

Relationship between flow rate and suction height with the Clean Jet 1600 Plus garden pump serving as an example

www.tip-pumpen.de
17

T.I.P.

TECHNIK + KOMPETENZ

Irrigation / Automation

Automated operation of pumps


Water tapping just as from the mains Available for all garden, submersible pressure, deep- well pumps Combination of pumps and control system Electronic control system protects from damage caused by operation in the absence of water Automatic on/off function Very simple, highly efficient installation Multiple options, adaptable to individual requirements

The cut-in and cut-out pressure can be set individually Automation is possible with all submersible pressure pumps, garden pumps and deep-well pumps from T.I.P. By installing an electronic or mechanical control system you can use the discharged fluid the same way as if you took it from the water mains: By simply opening or closing water taps. Apart from that, electronic control systems will protect your pump from damage caused by dry-running since these systems will cut out automatically in the absence of water. Electronic control systems will provide a pump control as a function of pressure and water flow rate. The Brio 2000-M control system will switch the pump on either when the tap is opened or as soon as pressure has dropped to a specific minimum value. When water tapping stops, the pump will switch off. The ON pressure can be set individually. Mechanical control systems will control the pump on the basis of an interaction between a pressure tank and the ON and OFF pressure. They will switch the pump on by enabling the current to flow. When the water-consuming appliance is switched off or the tap is shut, the current supply will be cut out, and the pump will switch off. The ON and OFF pressure can be set by a mechanic.

Automation: Very easy installation - high efficiency


In order to be actually used for automation, a pump has to be able to build up a minimum pressure of 1.5 bar. This basic condition is met by all garden, submersible pressure, cistern and deep-well pumps from T.I.P. Installation requires only a minimum of action. The control system, for instance, can be mounted directly onto the pump. As an alternative, a hose can be fitted between the pump and the control system. Another possibility of automation consists in fitting the pump with a pressure tank, an armoured hose and a pressure switch. Optionally, the pump and the pressure tank can be fitted directly to each other or connected by a hose.

The automated operation of a pump offers numerous benefits. For instance, it is possible to use water taken from wells or rainwater collected in cisterns for domestic water provision, e.g. for the operation of washing machines, showers or toilet flushing systems. Owing to its high efficiency and reliability, an automated pump will also convince when used for watering or the operation of sprinklers.

www.tip-pumpen.de
18

Irrigation / Automatic booster sets

TECHNIK + KOMPETENZ

T.I.P.

Automatic booster sets


HWA 4500 INOX: High-Capacity Automated Booster Set
Very powerful automated booster set in high-quality workmanship for watering, irrigation, domestic water supply with grey water, use of collected rainwater Pump housing made of high-grade steel Pressure gauge to facilitate monitoring of the operating pressure Electronic pump control provides additional protection from damage caused by dry-running A solid metal plate provides for a solid standing and ease of installation in the case of stationary use

An automatic booster set corresponds to the combination of a garden pump with an electronic control system. Our broad and carefully scaled range of garden pumps provides a variety of options, which allow the purposeful realisation of individual requirements. In addition, with the HWA 3000 INOX and HWA 4500 INOX, our range of products includes two conventional automatic booster sets in high-grade workmanship.
Automatic booster set Automatic booster set

HWA 3000 INOX

HWA 4500 INOX

Unit in high-quality workmanship Very powerful unit in high-quality workmanship High-grade steel pump housing Electronic pump control and High-grade steel pump housing Electronic pump control and pressure gauge pressure gauge Solid metal plate included Solid metal plate included

Max. flow rate Max. delivery height / pressure Nominal performance Pressure port Suction port Pump housing Cross weight Item number

2.800 l/h 42 m / 4,2 bar 550 Watt 33,25 mm (1 MT) 30,93 mm (1 FT) High-grade steel 7,3 kg 31142

4.350 l/h 50 m / 5,0 bar 1.200 Watt 33,25 mm (1 MT) 30,93 mm (1 FT) High-grade steel 11,1 kg 31193 The Brio 2000-M electronic control system excels by its extremely high reliability and functional safety. Easily and instantly installed, the Brio 2000-M allows the automation of any kind of pressure pump capable of generating a minimum of 1.5 bar. Unlike the cut-out pressure, the cut-in pressure is adjustable, since after closing the water tap cutting out will occur automatically as a function of performance. The Brio 2000-M is equipped with a pressure gauge for accurate pressure control. As an additional benefit, the Brio 2000-M will cut out the pump in the absence of water and thus prevent the pump from damage caused by dry-running.

Flow rate depending on the discharge height

50 m 42 m 40 m 30 m 20 m 10 m 150 l/h 600 l/h 1.500 l/h 2.400 l/h 42 m 40 m 30 m 20 m 10 m 800 l/h 1.400 l/h 2.700 l/h 3.500 l/h 3.900 l/h

Number of sprinklers
2x 5x

www.tip-pumpen.de
19

T.I.P.

TECHNIK + KOMPETENZ

Automatic water supply

Booster sets
Domestic water supply with grey water Pressure increase in the domestic water system Automated watering using sprinklers Withdrawal of water at a constant pressure Large tank for optimum pressure equalisation Units with anti dry-running feature and prefilter Pump housing made of impact-resistant plastic, sturdy cast or top-grade steel All units supplied with food-proof diaphragm

Domestic water supply counts among the key applications of booster sets. In an increasing number of households, people rather use rain, grey or groundwater for many applications instead of expensive and valuable drinking water taken from the mains. This makes sense, for instance, for flushing toilets, operating washing machines or supplying showers - and of course for irrigation.

Automatic irrigation is one of typical ranges of applications for which booster sets are especially suited. Normally, the expansion of the long flexible hoses which are commonly used is responsible for a pressure drop within the system. The size of the large tank of a booster set compensates for this and prevents the pump from cutting in again.

Pressure boosting in a domestic water system may be necessary for various reasons. For instance in the top storeys the water frequently arrives with a poor pressure. In such cases the installation of a booster set to act as a pressure-increasing system is recommendable. The cut-in and the cut-out pressure can be set very specifically, so that the insufficient pressure provided in the domestic water system can be increased to highly accurate target values. An anti dry-running feature prevents the hydraulic parts of pumps from possible overheating occurring as a result of operating the pump in the absence of liquid. This so-called dry-running is frequently the reason of considerable damage to the unit. The anti dry-running feature consistently suppresses this risk since it causes the pump to cut out in time. Prefilters are recommended as accessories, in particular for self-priming pumps. They will extend the lifetime of the pump since they filter out efficiently sand and solid matters from the fluid being conveyed. The high-quality filter mesh made of highly impact-resistant plastic can be cleaned conveniently so that it can be used over and over again. Some booster sets come with an anti dry-running feature and/or a prefilter as a standard. Units without these features can be retrofitted without any problems. You will find the appropriate accessories on pages 32 and 33.

Anti dry-running feature and prefilter

The cut-in and cut-out pressure can be set individually Almost all booster sets from T.I.P. are equipped with a mechanical control system. Upon reaching the cut-in or cut-out pressure, usually preset to 2 or 3 bar, respectively, the pump will cut in or cut out. Changing these preset values which are ideally suited for most installations must only be done by a qualified plumbing or electrical expert.

www.tip-pumpen.de
20

Booster sets

TECHNIK + KOMPETENZ

T.I.P.

Booster sets
The robust series: Cast-iron pump housings
Smooth-running, self-priming booster sets with pump housings made of robust cast iron and pressure tanks made of painted steel For discharging water at constant pressure, domestic water supply with grey water, pressure boosting, watering, irrigation Maintenance-free capacitor motor with thermal overload protection Compact, space-saving, lightweight units coming with an 18 L pressure tank Units with a large 24 L pressure tank for an increase of the water supply and a reduction of the cut-in/cut-out frequency All units come with a pressure gauge and a food-proof diaphragm

Booster set

Booster set

Booster set

Booster set

HWK 46/42
Solid starter unit Plastic pump housing 18 L pressure tank Compact design Low weight

HWW 900/25 Plus


Proven starter unit Pump housing made of cast iron 18 L pressure tank Compact design Very smooth-running pump

HWW 1200/25
Extremely powerful unit Pump housing made of cast iron 24 L pressure tank Large discharge volume and pressure Very smooth-running pump

HWW 3600 I
Powerful unit High-grade steel pump housing 18 L pressure tank Compact design

Max. flow rate Max. delivery height / pressure Nominal performance Pressure port Suction port Pump housing / Pressure tank Cross weight Item number

2.800 l/h 42 m / 4,2 bar 550 Watt 33,25 mm (1 MT) 33,25 mm (1 MT) Plastic / Steel 12,3 kg 31202

2.800 l/h 42 m / 4,2 bar 600 Watt 30,93 mm (1 FT) 30,93 mm (1 FT) Cast iron / Steel 14,7 kg 31300

4.300 l/h 50 m / 5,0 bar 1.200 Watt 30,93 mm (1 FT) 30,93 mm (1 FT) Cast iron / Steel 23,0 kg 31111

3.600 l/h 40 m / 4,0 bar 650 Watt 30,93 mm (1 FT) 30,93 mm (1 FT) High-grade steel / Steel 13,1 kg 31188

Flow rate depending on the discharge height

50 m 42 m 40 m 30 m 20 m 10 m 150 l/h 700 l/h 1.850 l/h 2.500 l/h 42 m 40 m 30 m 20 m 10 m 150 l/h 600 l/h 1.500 l/h 2.400 l/h 42 m 40 m 30 m 20 m 10 m 800 l/h 1.700 l/h 2.650 l/h 3.600 l/h 4.100 l/h 40 m 30 m 20 m 10 m 1.250 l/h 2.430 l/h 3.200 l/h

Number of sprinklers
1x 1x 5x 2x

www.tip-pumpen.de
21

T.I.P.

TECHNIK + KOMPETENZ

Automatic water supply

Booster sets
The higher graded series: High-grade-steel pump housing
Self-priming booster sets with pump housings made of high-grade steel and pressure tanks made of painted steel For discharging water at constant pressure, domestic water supply with grey water, pressure boosting, watering, irrigation Maintenance-free capacitor motor with thermal overload protection Units equipped with a high-quality prefilter and/or a very efficient anti dry-running feature All units with a large 24 L pressure tank for an increase of the water supply and a reduction of the cut-in/cut-out frequency All units come with a pressure gauge and a food-proof diaphragm

Booster set

Booster set

Booster set

Booster set

HWW 1000/25 Plus


Powerful unit High-grade steel pump housing 24 L pressure tank

HWW 1000/25 Plus TLS HWW 1000/25 Plus F


Powerful and efficient unit High-grade steel pump housing 24 L pressure tank Anti dry-running feature Powerful unit High-grade steel pump housing 24 L pressure tank High-quality prefilter

HWW 1000/25 Plus TLS F


Powerful unit High-grade steel pump housing 24 L pressure tank Anti dry-running feature High-quality prefilter

Max. flow rate Max. delivery height / pressure Nominal performance Pressure port Suction port Pump housing / Pressure tank Cross weight Item number

3.300 l/h 46 m / 4,6 bar 800 Watt 30,93 mm (1 FT) 30,93 mm (1 FT) High-grade steel / Steel 13,5 kg 31146

3.300 l/h 46 m / 4,6 bar 800 Watt 30,93 mm (1 FT) 30,93 mm (1 FT) High-grade steel / Steel 13,9 kg 31145

3.300 l/h 46 m / 4,6 bar 800 Watt 30,93 mm (1 FT) 30,93 mm (1 FT) High-grade steel / Steel 14,2 kg 31144

3.300 l/h 46 m / 4,6 bar 800 Watt 30,93 mm (1 FT) 30,93 mm (1 FT) High-grade steel / Steel 14,6 kg 31141

Flow rate depending on the discharge height

46 m 42 m 40 m 30 m 20 m 10 m 400 l/h 460 l/h 1.200 l/h 2.550 l/h 3.200 l/h

46 m 42 m 40 m 30 m 20 m 10 m 400 l/h 460 l/h 1.200 l/h 2.550 l/h 3.200 l/h

46 m 42 m 40 m 30 m 20 m 10 m 400 l/h 460 l/h 1.200 l/h 2.550 l/h 3.200 l/h

46 m 42 m 40 m 30 m 20 m 10 m 400 l/h 460 l/h 1.200 l/h 2.550 l/h 3.200 l/h

Number of sprinklers
2x 2x 2x 2x

www.tip-pumpen.de
22

Booster sets

TECHNIK + KOMPETENZ

T.I.P.

Booster sets

Booster set

Booster set

Booster set

Booster set

HWW 1300/25 Plus


Powerful and efficient unit High-grade steel pump housing 24 L pressure tank

HWW 1300/25 Plus TLS HWW 1300/25 Plus TLS/F


Powerful and efficient unit High-grade steel pump housing 24 L pressure tank Anti dry-running feature Powerful and efficient unit High-grade steel pump housing 24 L pressure tank Anti dry-running feature High-quality prefilter

HWW 1600/25 Plus TLS


Particularly powerful unit with very large discharge volume High-grade steel pump housing 24 L pressure tank Anti dry-running feature

Max. flow rate Max. delivery height / pressure Nominal performance Pressure port Suction port Pump housing / Pressure tank Cross weight Item number

4.200 l/h 50 m / 5,0 bar 1.200 Watt 30,93 mm (1 FT) 30,93 mm (1 FT) High-grade steel / Steel 16,0 kg 31147

4.200 l/h 50 m / 5,0 bar 1.200 Watt 30,93 mm (1 FT) 30,93 mm (1 FT) High-grade steel / Steel 16,4 kg 31158

4.200 l/h 50 m / 5,0 bar 1.200 Watt 30,93 mm (1 FT) 30,93 mm (1 FT) High-grade steel / Steel 17,2 kg 31157

5.400 l/h 50 m / 5,0 bar 1.600 Watt 30,93 mm (1 FT) 41,91 mm (1 1/4 MT) High-grade steel / Steel 18,6 kg 31148

Flow rate depending on the discharge height

50 m 42 m 40 m 30 m 20 m 10 m 1.100 l/h 1.200 l/h 2.500 l/h 3.100 l/h 3.800 l/h

50 m 42 m 40 m 30 m 20 m 10 m 1.100 l/h 1.200 l/h 2.500 l/h 3.100 l/h 3.800 l/h

50 m 42 m 40 m 30 m 20 m 10 m 1.100 l/h 1.200 l/h 2.500 l/h 3.100 l/h 3.800 l/h

50 m 42 m 40 m 30 m 20 m 10 m 1.000 l/h 1.500 l/h 3.200 l/h 5.000 l/h 5.100 l/h

Number of sprinklers
4x 4x 4x 6x

www.tip-pumpen.de
23

T.I.P.

TECHNIK + KOMPETENZ

Automatic water supply

High-grade steel booster sets


The top workmanship series: All high-grade steel units
Self-priming booster sets with pump housings and pressure tanks made of high-grade steel For discharging water at constant pressure, domestic water supply with grey water, pressure boosting, watering, irrigation Very solid units, therefore particularly suited for installation in shafts Maintenance-free capacitor motor with thermal overload protection Units equipped with a high-quality prefilter and/or a very efficient anti dry-running feature All units come with a large 24 L pressure tank, a pressure gauge and a food-proof diaphragm

Booster set

Booster set

Booster set

Booster set

HWW 3000 INOX

HWW 4500 INOX

HWW INOX 1300 Plus F

HWW INOX 1600 TLS

Reliable starter unit in all Powerful and efficient unit high-grade steel series Pump housing and pressure Pump housing and pressure tank made of high-grade steel tank made of high-grade steel 24 L pressure tank 24 L pressure tank

Powerful and efficient unit Particularly powerful unit with Pump housing and pressure very large discharge volume tank made of high-grade steel Pump housing and pressure 24 L pressure tank tank made of high-grade steel High-quality prefilter 24 L pressure tank Anti dry-running feature

Max. flow rate Max. delivery height / pressure Nominal performance Pressure port Suction port Pump housing / Pressure tank Cross weight Item number

2.950 l/h 42 m / 4,2 bar 550 Watt 30,93 mm (1 FT) 30,93 mm (1 FT) High-grade steel 12,2 kg 31143

4.350 l/h 50 m / 5,0 bar 1.200 Watt 30,93 mm (1 FT) 30,93 mm (1 FT) High-grade steel 16,2 kg 31140

4.200 l/h 50 m / 5,0 bar 1.200 Watt 30,93 mm (1 FT) 30,93 mm (1 FT) High-grade steel 17,1 kg 31155

5.400 l/h 50 m / 5,0 bar 1.600 Watt 30,93 mm (1 FT) 41,91 mm (1 1/4 MT) High-grade steel 18,5 kg 31163

Flow rate depending on the discharge height

50 m 42 m 40 m 30 m 20 m 10 m 150 l/h 600 l/h 1.500 l/h 2.400 l/h 42 m 40 m 30 m 20 m 10 m 800 l/h 1.400 l/h 2.700 l/h 3.500 l/h 3.900 l/h

50 m 42 m 40 m 30 m 20 m 10 m 700 l/h 1.200 l/h 2.500 l/h 3.100 l/h 3.800 l/h

50 m 42 m 40 m 30 m 20 m 10 m 1.000 l/h 1.500 l/h 3.200 l/h 5.000 l/h 5.100 l/h

Number of sprinklers
1x 5x 4x 6x

www.tip-pumpen.de
24

General information

TECHNIK + KOMPETENZ

T.I.P.

Automated water supply with pump and pressure tank


Installing a garden, deep-well or submersible pressure pump in combination with a pressure tank will produce an automated water supply system offering the functioning and benefits of a booster set: Pressure equalisation and reduced switching frequency. Besides the pressure tank, the basic equipment requires the following components: An electronic control system or a pressure switch for automated operation, a pressure gauge for pressure monitoring, a 3-way diverter for various connections and an armoured hose for connecting the pressure tank. It is e.g. possible to install a hose of some length between the pump and the tank. In this way the pump can be installed in a cistern, and the water being discharged can then be conveyed into the house where the pressure tank is installed, may be together with a pre-filter. This example is a highly efficient system for domestic water supply. Together with the necessary accessories which you find from page 31 it is possible to achieve highly versatile and efficient solutions.

oder

oder

Functioning of the pressure tank


As is generally the case with booster sets, the pressure tank plays a major role for automated water supply. The larger the pressure tank, the less frequently will the pump have to cut in or cut out, respectively. The underlying principle is as simple as that: If you tap a small quantity of liquid, such as a glass of water, the water volume contained in the pressure tank will prevent the pump from cutting in. With the size of the tank, the volume of the liquid contained in it will also increase, which means that the pump will have to cut in less frequently. Considering that each start of the pump requires electrical energy, the reduction of the cut-in frequency will clearly reduce the energy consumption, thus saving costs. As another positive side effect of the reduced number of cut-in operations the noise caused by the start and operation of the pump will be reduced. Booster sets from T.I.P. are equipped with pressure tanks of different sizes, ranging from 18 to 24 L volume. As a special unit, we offer the HWW 1300/50 Plus TLS which comes with a particularly large 50 L pressure tank. In this way, the bandwidth ranges from compact, space-saving low-weight models up to particularly large units. These differences enable an on-site selection to be made on the basis of individual criteria and specific conditions.

How to determine the appropriate booster set


Calculation example of the total delivery height
Water consumption: Sink: 6 L/min Bath tub: 15 L/min Shower: 10 L/min Washing machine: 10 L/min Dishwasher: 8 L/min Cistern (toilet flushing tank): 4 L/min

HM

min. 10 l/min

Delivery height (HM) + 10 m Friction loss (15%) + 1,5 m = 11,5 m Min. pressure* + 20 m Total delivery height = 31,5 m
* Min. delivery pressure 2,0 bar W 20 m delivery height

It takes just a few calculations to find out the suitable type of booster set for your requirements. First of all, use the opposite chart to determine your max. water consumption. Example: If you wish that your bath tub, dishwasher and washing machine can be used at the same time, you simply add up the individual values and arrive at 33 l/min for the max. water consumption. Multiplied by 60, this leads to the water volume per hour: 792 l/h. The next thing to do is to calculate the total discharge height. First of all, you need the actual discharge height - i.e. the height difference between the water surface and the highest place of withdrawal, increased by 15% to allow for the calculation of friction losses. Subsequently, you consider the required min. pressure which is defined by the consumer device with the highest operating pressure. The pressure, here indicated in terms of bar, is then to be multiplied by 10 to convert it to metres. Adding the two values will result in the arithmetical

total discharge height. Example: Your booster set is supposed to be able to withdraw water from a depth of 4 m and convey it to the highest withdrawal place in 6 m height (actual discharge height = 10 m). Increased by 15%, you arrive at 11.15 m. The minimum pressure is supposed to be 2 bar. When converted, this corresponds to 20 m. When adding up these values (11.5 m plus 20 m) you will arrive at the total discharge height of 31.5 m. On the basis of the calculated max. water consumption and the mathematical total discharge height, all you need to do is to refer to the discharge volume and discharge height charts for the specific booster set to see whether a specific product will fit your requirements. For instance, you will see on page 21 that the HWW 3600 I (30 m / 1,250 l/h) will actually satisfy your needs, whereas the HWW 46/42 (30 m / 700 l/h) will not.

www.tip-pumpen.de
25

T.I.P.

TECHNIK + KOMPETENZ

Automatic water supply

Special booster set designed to save energy


Booster set: HWW 1300/50 Plus TLS
The capacity of the pressure tank is of a very high significance with regard to the functioning and efficiency of a booster set. Compared to smaller designs, a larger tank will ensure an increased water supply. This means a clearly improved pressure equalisation so that the operation of the booster set requires a reduced number of switching actions. As a pleasant side consequence both the electricity consumption and the operating noise will be reduced - besides, the reduced switching frequency leads to a more sparing operation of the unit. Quite a few booster sets from T.I.P. come with a relatively large sized pressure tank in their standard version. In most cases, this is a pressure tank with a volume of 24 litres. With the HWW 1300/50 Plus TLS, we have designed a device with a pressure tank volume of 50 litres, which means a volume of more than double the standard size. In this way we provide the user with totally new options to plan their installation even more purposeful - based on their specific wishes and particular requirements.

Particularly efficent owing to large 50 L pressure tank

The HWW 1300/50 Plus TLS special booster set is equipped with a very powerful, self priming pump with a housing made of high-grade steel. With its considerable max. discharge flow rate and its high maximum pressure, in combination with the large pressure tank and the armoured hose, this unit is best suited for all application areas of booster sets, in particular for domestic water supply and as a pressure increase system. This superior type is rounded off by an integrated anti dry-running feature.

Booster set with 50 L pressure tank

HWW 1300/50 Plus TLS


Very large 24 L pressure tank Integrated anti dry-running feature High-grade-steel pump housing Suitable for all areas of use of booster sets - in particular to be used as a pressure increase system

Max. flow rate Max. delivery height / pressure Nominal performance Pressure port Suction port Pump housing / Pressure tank Cross weight Item number

4.200 l/h 50 m / 5,0 bar 1.200 Watt 30,93 mm (1 FT) 30,93 mm (1 FT) High-grade steel / Steel 21,2 kg 31311 The HWW 1300/50 Plus TLS booster set is the ideal device for users who attach great importance to a clearly reduced switching frequency. In particular in context with domestic water supply in grey water, this is an important criterion since the resulting decrease of the switching frequency will also reduce the noise level involved with the start and operation of the pump. This noise may be extremely disturbing, in particular in times of silence or at nighttime, and it may be considerably decreased by selecting a pump that is equipped with a large pressure tank.

Flow rate depending on the discharge height

50 m 42 m 40 m 30 m 20 m 10 m 1.100 l/h 1.200 l/h 2.500 l/h 3.100 l/h 3.800 l/h

Number of sprinklers
4x

www.tip-pumpen.de
26

Automatic water supply

TECHNIK + KOMPETENZ

T.I.P.

Special booster set for deep intake


Booster set: HWW AP 1000 N 20

max. 20 m

max. 45 m

In the case of self-priming pumps, physical laws usually restrict the suction height to a maximum of 9 m. Owing to an innovative water recirculating process the HWW AP 1000 N 20 is capable of extending the suction depth down to 20 m. This permits particularly deeplying water resources to be used efficiently for all typical areas of application of booster sets.

Booster set for deep intake

HWW AP 1000 N 20
Special development for deep intake down to 20 m Special water recirculation system using an injector and circulation line Very smooth-running unit with pump housing made of cast iron Suitable for all typical areas of use of booster sets

Max. flow rate Max. delivery height / pressure Nominal performance Pressure port Suction port Pump housing / Pressure tank Cross weight Item number

2.600 l/h 45 m / 4,5 bar 1.000 Watt 30,93 mm (1 FT) 39,59 mm (1 1/4 FT) Cast iron / Steel 23,0 kg 31078 While conventional booster sets are equipped with just a suction line, the units conceived for deep intake feature an additional circulation line with a separate port. When the liquid is sucked in, a part of the water is led back through the circulation line into an injector. This generates the pressure that is needed for taking in water from great depth.

Flow rate depending on the suction height

Delivery height Suction height 10 m 10 m 15 m 20 m 40 l/min 35 l/min 24 l/min 15 m 32 l/min 28 l/min 16 l/min 25 m 18 l/min 14 l/min 10 l/min 35 m 8 l/min 4 l/min

www.tip-pumpen.de
27

T.I.P.

TECHNIK + KOMPETENZ

Special pumps

Petrol-engine pumps
Operation independent of the electrical mains Ideal pumps for use in allotment gardens, weekend homes, agricultural applications, and on constructionsites Pump housing made of aluminium Drainage, irrigation, evacuation, emergency drainage Robust, air-cooled 4-stroke engines Easy engine start by means of a rope pull

Petrol-engine pumps have proven to be the optimum solution in places which are far from the electrical mains. The LTP series includes units of a very high quality equipped with robust, powerful 4-stroke engines. The convenient equipment includes connection pieces for the pressureand suction-side ports, an integrated non-return flap on the suction side and an oil-level protection feature (Auto-Stop).

For agricultural use, such as watering or irrigation, petrol-engine pumps with their very high flow rates have proven to be almost perfectly suited. The typical areas of use include emptying or filling of ponds and basins far away from any available electrical connection, or the water supply of construction-sites, allotment gardens, weekend homes or garden sheds.

During inundations, the electricity supply frequently collapses so that electrical pumps cannot be used for emergency drainage. Also, flooding leads to situations where the use of an electrically driven pump is not advisable for reason of the hazard of an electrical shock. In emergency cases like that, petrol-engine pumps with their large capacity are the almost perfect solution.

Maintenance of petrol-engine pumps


The careful maintenance and care of petrolengine pumps include the check of the oil level prior to each start of the unit. The units of the LTP series are equipped with an AutoStop feature. This convenient feature protects the unit from damage caused by the absence of oil, since the motor cannot be started unless a sufficient quantity of motor oil is available. The oil should be changed at least once per year. In this context, observing the local regulations regarding the disposal of waste oil is imperative. The cleaning of the spark plug and, where necessary, a correction of the electrode gap should be performed every six months or after 100 hours of operation. Dirty air filters will obstruct the airflow to the carburettor. To avoid functional disturbances, this means that the air filter should be inspected regularly and cleaned or replaced, if necessary. Generally, it is recommended to check the air filter for contamination prior to each use. The filter should be cleaned at the latest every three months or after 50 hours of operation. If the unit is used in a highly contaminated or dusty environment, the cleaning intervals ought to be shortened appropriately.

Starting on page 31, you will find high-quality accessories for the LTP series - for instance, hoses with large dimensions which are also available by the metre. Professional installations can be realised using joint bolt clips, connection pieces and brass foot valves. The reducing piece coming with the LTP 40 serves to reduce the connection dimension from 47,80 mm (1 MT) to 41,91 mm (1 MT).

www.tip-pumpen.de
28

Petrol-engine driven water pumps

TECHNIK + KOMPETENZ

T.I.P.

Petrol-engine pumps

Petrol-engine pump

Petrol-engine pump

Petrol-engine pump

LTP 40/10
Flow rate max. Pressure max. Delivery height max. Suction height max. Cylinder capacity Power max. Pressure port Suction port Tank volume Fuel Liquid temperature min. / max. Item number 10.000 l/h 1,5 bar 15 m 4m 97,7 ccm 1,1 kW (1,5 HP) 47,80 mm (1 1/2 MT), 40 mm 47,80 mm (1 1/2 MT), 40 mm 1,4 l Petrol, unleaded 2 C / 35 C 30131

LTP 50/25
25.000 l/h 2,6 bar 26 m 6m 196 ccm 3,8 kW (5,1 HP) 59,61 mm (2 MT), 50 mm 59,61 mm (2 MT), 50 mm 3,6 l Petrol, unleaded 2 C / 40 C 30132
26 m 24 m 20 m 16 m 6.700 l/h 8.800 l/h 9.900 l/h 9.950 l/h 12 m 8m 4m 1m

LTP 80/48
48.000 l/h 3,0 bar 30 m 6m 196 ccm 3,8 kW (5,1 HP) 87,88 mm (3 MT), 75 mm 87,88 mm (3 MT), 75 mm 3,6 l Petrol, unleaded 2 C / 40 C 30129
30 m 24 m 20 m 16 m 12 m 8m 4m 1m

Flow rate depending on the discharge height

15 m 12 m 8m 4m 1m

11.100 l/h 17.000 l/h 20.800 l/h 23.100 l/h 24.500 l/h 24.700 l/h 24.900 l/h

29.000 l/h 36.000 l/h 41.200 l/h 44.500 l/h 47.000 l/h 47.600 l/h 47.800 l/h

www.tip-pumpen.de
29

T.I.P.

TECHNIK + KOMPETENZ

Special pumps

Special pump for discharging fuel


Robust peripheral pump for discharging diesel fuel, fuel oil and rapeseed oil Pump housing made of cast iron Impeller made of brass Suitable for fuelling vehicles Filling or emptying of fuel oil tanks Comes complete with gun-type fuelling nozzle, fuelling hose, suction hose and brass foot valve

Special pump

MultiOil 35 M
Flow rate max. Delivery height max. Pressure max. Nominal performance Pressure port Suction port Suction height max. Liquid temperature max. Impeller Power cord Weight Item number 35 l/min (2.100 l/h) 35 m 3,5 bar 550 Watt 30,93 mm (1 FT) 30,93 mm (1 FT) 5m 40 C Brass 1,5 m 10,8 kg 30070
35 m 30 m 25 m 20 m 15 m 10 m 5m 1m 3,5 l/min 7 l/min 11 l/min 16,5 l/min 21,5 l/min 27,5 l/min 34 l/min

Discharging liquids such as diesel fuel, fuel oil and rapeseed oil is only possible with pumps which were especially designed for these purposes. The MultiOil 35 M is a very robust special development suited for filling and emptying fuel oil tanks or for fuelling trucks, cars, construction and agricultural machines with diesel fuel and rapeseed oil. The pump housing made of cast-iron and the impeller made of brass guarantee a long lifetime. The MultiOil 35 M comes completely equipped with a gun-type fuelling nozzle, a fuelling hose, a suction hose and a brass foot valve.

Flow rate depending on the discharge height

www.tip-pumpen.de
30

Accessories

TECHNIK + KOMPETENZ

T.I.P.

Drainage hose clean water, 10 m


Drainage hose, 10 m, infinitely extendable. Suitable for connection not only to submersible pumps, but also to submersible pressure pumps since the hose will stand pressures up to 6 bar. For feeding on clean and slightly soiled water from swimming pools, basins, ponds, cisterns etc. Accessory items: Connection pieces for pumps with 30.93 mm (1 FT), 33.25 mm (1 MT), 39.59 mm (1 FT) and 41.91 mm (1 MT). 10 m Item number

Drainage hose dirty water, 10 m


The large interior diameter (28 mm) ensures a speedy drainage and minimises the risk of clogging. Infinitely extendable when connected to additional drainage hoses. For feeding on clean and soiled water from the cellars, basins, ponds, cisterns etc. Accessory items: Connection pieces for pumps with 30.93 mm (1 FT), 33.25 mm (1 MT), 39.59 mm (1 FT) and 41.91 mm (1 MT).

Suction set 4m/7m


Suction hose set made of plastic. Comes complete with coarse inlet filter and integrated check valve. For garden pumps, booster sets and automatic booster sets. Special design for use with garden pump starter sets. Accessory items: Connection pieces for pumps with 33.25 mm (1 MT) and 30.93 mm (1 FT).

ECO brass suction set 4m/7m


For suction and pressure applications up to 6 bar operating pressure and 60 % vacuum. Made of kink and abrasion-proof material. Covered hard-PVC helix; comes with a brass foot valve with high-grade steel coarse filter and brass connector for connection to the pump. Suitable for all garden pumps, booster sets and automatic booster sets. Accessory items: Connection pieces for pumps with 30.93 mm (1 FT) and 33.25 mm (1 MT). 4m Item number 7m Item number 30906

4m Item number 7m Item number

31009

31008

10 m Item number

30904

31012

30907

PROFI brass suction set 4m/7m


For suction and pressure applications up to 6 bar operating pressure and 60 % vacuum. Made of kink and abrasion-proof material. Covered hard-PVC helix; comes complete with a threaded brass high-pressure suction coupling piece with GK connector, brass foot valve with high-grade steel coarse filter and brass clamping brackets. Professional accessory item for all garden pumps, booster sets and automatic booster sets. 4m Item number 7m Item number

Pump spiral hose for large-scale pumps (petrol-engine pumps)


Professional design. Made of kink and abrasion-proof material. Covered hard-PVC helix. For suction/ pressure applications up to: 40 mm (1 ) - 6 bar operating pressure and 60 % vacuum 50 mm (2) - 5 bar operating pressure and 50 % vacuum 75 mm (3) - 4 bar operating pressure and 40 % vacuum 40 mm (1 ) / rm Item number 30931 50 mm (2) / rm Item number 30932 75 mm (3) / rm Item number 30933

Pump spiral hose for large-scale pumps (petrol-engine pumps)


Professional design. Made of kink and abrasion-proof material. Covered hard-PVC helix. For suction/ pressure applications up to: 40 mm (1 ) - 6 bar operating pressure and 60 % vacuum 50 mm (2) - 5 bar operating pressure and 50 % vacuum 75 mm (3) - 4 bar operating pressure and 40 % vacuum 40 mm (1 ) / 50 m Item number 30934 50 mm (2) / 50 m Item number 30935 75 mm (3) / 50 m Item number 30936

Hose accessories

Foot valve, complete, brass 40 mm (1 ) Item no. 30937 50,8 mm (2) Item no. 30938 ; Joint bolt clip 43 - 47 mm / Width: 18 mm for 40 mm (1 ) hoses Item no. 30948 54-58 mm / Width: 20 mm for 50 mm (2) hoses Item no. 30949 79-85 mm / Width: 25 mm for 75 mm (3) hoses Item no. 30950 = GK connection piece, brass 45,48 mm (1 FT) Item no. 30946

31010 31011

www.tip-pumpen.de
31

T.I.P.

TECHNIK + KOMPETENZ

Accessories

Ball-type float with foot valve for cistern pumps


For floating withdrawal of rainwater from cisterns, containers, wells etc. Prevents dirt particles such as sand from being sucked in from the bottom. To be used in combination with the inlet hose for cistern pumps (Item number 30913).

Inlet hose with connection piece for cistern pumps


Food-proof, pressure resistant hose for floating withdrawal of rainwater from cisterns, containers, wells etc. Prevents dirt particles such as sand from being sucked in from the bottom. Connection 39.59 mm (1 FT), and 33,25 mm (1 MT) Length 2,4 m To be used in combination with the ball-type float for cistern pumps (Item number 30914).

Lowering rope 20 m
Heavy-duty nylon lowering rope. Suitable to be fastened to submersible pumps for lowering them down into shafts.

TPT 20 support system (multifunctional)


Versatile support system for all submersible pumps, submersible pressure and deep-well pumps. Increased installation versatility owing to horizontal or upright positioning of the pump. Increased stability and functional safety of the pump by installing the support system to the edges of cisterns or wells. When used as a wall support, the device is ideally suited as a storage place for the pump - e.g. in periods of frost.

Item number

30914

Item number

30913

20 m Item number

30912

Item number

30947

Multi-purpose water filter G 5 / G 7 / G 10


Prefilter for use with garden pumps and booster sets. This filter will extend the lifetime of the pump. It consists of three sections, with threaded ring for filter glass. Brass bleeding screw, high-quality 30,93 mm (1 FT) connection thread made of brass, including washable filter cartridge for sand and solids. Transparent filter chamber made of highly impact-resistant plastic. Max. flow rate 7.000 l/h G 5, 127 mm (5) Item number 31052 G 7, 178 mm (7) Item number 31058 G 10, 254 mm (10) Item number 31050

Disposable filter cartridges Reusable filter cartridges


Disposable fibre filter cartridge

Active carbon special filter Polyphosphate special filter


Active carbon filter for removing

Active carbon filter cartridge Polyphosphate filter cartridge

for filtering out sand and solids. Filtering effect 80 . ; Washable plastic filter cartridge for sand and solids. 127 mm (5) for filter G 5 Item no. 31054 178 mm (7) for filter G 7 Item no. 31056 254 mm (10) for filter G 10 Item no. 31055

Active carbon filter cartridge chlorine, odours, taste and cloudi- For use in active carbon water ness from the mains water. filter, item number 31081 - to Recommended flow rate: 12 l/min improve water quality. ; Polyphosphate special filter for lowering mains water hardness. Provides efficient protection from calcination and also protects from damage caused by corrosion. Recommended flow rate: 4 l/min ; Polyphosphate filter cartridge

For use in polyphosphate water filter, item number 31084 - for removing mains water hardness.

G 10, 254 mm (10) Item number 31081

127 mm (5) for filter G 5 Item no. 31053 178 mm (7) for filter G 7 Item no. 31057 254 mm (10) for filter G 10 Item no. 31051

254 mm (10) for filter G 10 Item number 31082

G 10, 254 mm (10) Item number 31084

254 mm (10) for filter G 10 Item number 31083

www.tip-pumpen.de
32

Accessories

TECHNIK + KOMPETENZ

T.I.P.

Pressure gauge Pressure switch


Pressure gauge

Anti dry-running feature TLS 100 E


Conveniently retrofittable to all booster sets and garden pumps. Protects the device from damage caused by insufficient water level. Optical functions and malfunctions indicator. Inlet 33,25 mm (1 MT) Outlet 30,93 mm (1 FT)

Elektronic control system Brio 2000-M


Its simple installation allows you to automate any kind of pressure pump delivering more than 1.5 bar. Protects from damage caused by dry-running. The pump will cut in automatically as soon as the minimum pressure is reached. After shutting the consumer, automated cutting out will occur as a function of performance. Comes with a pressure gauge and double nipple. Inlet 33,25 mm (1 MT) or 30,93 mm (1 FT) Outlet 33,25 mm (1 MT) Cut-in pressure 1,0 - 3,5 bar Operating overpressure max. 10 bar Connection port 33,25 mm (1 MT) Fluid temperature max. 55 C Item number 30241

Armoured hose 60 cm
Flexible, rust-free connection hose. Simple, fast installation. Perfectly suited for connecting water pipe and pump, heating boiler or pressure tanks. For water distribution in heating and airconditioning installations. Suitable for drinking water. Food-proof. Includes gaskets. Operating temperature min. / max. - 5 C / + 100 C Operating pressure max. 10 bar Connection port 30,93 mm (1 FT) / 33,25 mm (1 MT) Item number 30903

For accurate pressure control. Measuring range up to 6 bar max. Connection port 13,16 mm (1/4 MT) ; Pressure switch Used to automate the on / off function in combination with the appropriate additional accessories. Connection port 11,89 mm (1/4 FT) Fluid temp. max. 35 C Weight 0,37 kg

Item number 31003

;
Item number 31002

Item number

30915

Membrane for all booster sets


Food-proof pressure tank membrane made of high-quality EPDM. Suitable for drinking water. Suitable for installation in all booster sets. Volume max. 24 L Fluid temerature max. 90 C Thickness 1,8 mm

Pressure tank Steel


Complete with food-proof membrane, flange and vessel valve. Volume Connection port Weight 24 L 26,44 mm / (3/4 MT) 4,4 kg

Pressure tank High-grade steel


Complete with food-proof membrane, flange and vessel valve. Volume Connection port Weight 24 L 26,44 mm / (3/4 MT) 4,0 kg

Vibration dampener VD 4
This vibration dampener set is intended for units such as booster sets, automatic booster sets or garden pumps. Their use clearly reduces the transmission of noise. Owing to the use of high-quality material in their production (rubber), abrasion, scratching or skidding is excluded. The required fastening material comes with the set.

Item number

30905

Item number

30995

Item number

30996

Item number

30943

www.tip-pumpen.de
33

T.I.P.

TECHNIK + KOMPETENZ

Accessories

SW connection bents

Double nipple Reducer piece


Double nipple 47,80 mm (1 MT) 47,80 mm (1 MT)

Multi-dimensional connection piece Connection bent


Multi-dimensional connection piece 30,93 mm (1 FT) 26,44 mm ( MT) Hose connection 28 mm + 34 mm ; Connection bent 39,59 mm (1 FT) 33,25 mm (1 MT)

Multi-dimensional connection bent


Multi-dimensional connection bent 39,59 mm (1 FT) 26,44 mm ( MT) Hose connection 28 mm + 34 mm

SW connection bent 39,59 mm (1 FT) hose connection 32 mm

; SW connection bent 45,48 mm (1 FT) hose connection 38 mm

; Reducer piece 45,48 mm (1 FT) 41,91 mm (1 MT)

Item number 30909

Item number 30921

Item number 30941

;
Item number 30910

;
Item number 30923

;
Item number 30917

Item number

30908

Multi-dimensional connection piece Muffle


Multi-dimensional connection piece 41,91 mm (1 MT) 26,44 mm ( MT) Hose connection 28 mm + 34 mm ; Muffle 39,59 mm (1 FT) 39,59 mm (1 FT)

Double nipple
Double nipple 33,25 mm (1 MT) 33,25 mm (1 MT)

Reducing nipple Reducer piece


Reducing nipple 47,80 mm (1 MT) 41,91 mm (1 MT)

Check (non-return) valve - plastic Foot valve - brass


Check (non-return) valve - plastic 39,59 mm (1 FT) 39,59 mm (1 FT)

; Double nipple 140 mm long 33,25 mm (1 MT) 33,25 mm (1 MT)

; Reducer piece 41,91 mm (1 MT) 30,93 mm (1 FT)

; Foot valve, complete, brass 26 mm (1)

Item number 30920

Item number 30942

Item number 30911

Item number 30924

;
Item number 30945

;
Item number 30944

;
Item number 30926

;
Item number 30955

www.tip-pumpen.de
34

Contact

TECHNIK + KOMPETENZ

T.I.P.

T.I.P. Technische Industrie Produkte GmbH


Siemensstrae 17 D - 74915 Waibstadt Tel. +49 (0)7263 9125-0 Fax +49 (0)7263 9125-25 info@tip-pumpen.de www.tip-pumpen.de

Spare parts and repair


Please contact us per e-mail, per fax, on the internet or by post: E-mail: Fax: Internet: Post: service@tip-pumpen.de +49 (0)7263 9125-85 www.tip-pumpen.de T.I.P. Technische Industrie Produkte GmbH Abt. Ersatzteile und Reparaturen (Spare pars and repair dept.) Siemensstrae 17 D - 74915 Waibstadt

Service hotline for technical questions:


+49 (0)7263 9125-82 +49 (0)7263 9125-83 Monday through Friday from 15.00 to 17.00 oclock.
T.I.P. Technische Industrie Produkte GmbH The data given in the catalogue do not represent any warranty of a promised quality. Specifications may vary as a result of technological progress. We assume no liability for typing errors.

Design: Angelika Zeck, Diplom-Designerin, az-grafik@t-online.de

www.tip-pumpen.de
35

Pumpen

T.I.P .

The Pump Pros


Siemensstrae 17 D - 74915 Waibstadt Tel. +49 7263 9125-0 Fax +49 07263 9125-25 www.tip-pumpen.de info@tip-pumpen.de

www.tip-pumpen.de

You might also like