Professional Documents
Culture Documents
Setup Manuals
Setup Manual for Kodak CR 800 / 900 / 500 / 850 / 950 with LASER IMAGER Products
1
setup valid also for Kodak PACS LINK 25 PRINT SERVER.
DICOM Network
Fiber Cable
iew
00 DryV
3M 87
Fiber Cable
Note: This setup is basically also valid for 8800/8700 Dual camera
by basically using the correspondent Model into 9410 Local Printers
Note: CR always sends 2:1 format Portrait-1column-2 rows, with images 90-degree rotated,
therefore some limitations are present if the format 2:1 side by side is wished
Note: if images are printed too dark, set TFT=Siews87b.w87 to print them lighter (see below)
n Formatting: Max Img Band=4, Max Band per Page=20, Max Img Col=0
n Formatting: Max Img Row=0, Min Horiz Sep=0, Min Vert Sep=6
n Formatting: Trim Width when enabled=1, Trim Width when disabled=0
n Formatting: Pixel Pitch=12.8205
n Image Processing: Grayscale=On, Max Image Dmax=3.1
n SCU: Density Space= On, Perception LUT =On
n M952 Usage: Min H/V Mag=1, Max H/V Mag=64, Min Dmax 952=1.7
9410 Setup:
n on Device Setup, LOCAL PRINTERS:
n Printer=8700, Model=8700, Output=Fiber
n Baud=19200, Parity=None, Data=8, Stop=1, Command Set=Superset
n Pixel=12, Header/Line, Timeout=60, Transfer Rate=2 MHz
n Film Mismatch=Print Always, Interpolation Type=831
n Interp Num=5, Max.Density=300, Contrast=6, Border Density=0
n TFT/ULUT Emulation=On, Installed TFT/ULUT=Ver693c0.w87
n on Device Setup, SCP PRINTERS, Current Providers:
n Printer=8700, AE Title= NER_9410, Port= 1024, Max Associations= 5
n on Device Setup, SCP PRINTERS, Registered Users:
n SCU AETitle= accordingly, SCU IPAddr=accordingly, SCP=8700
n Copies=1, Contrast Table=2, TFT/ULUT=Wrkstn2a.w87 (or Siews87b.w87)
n Max.Density=300, Border Density=0, Mag.Type=8, Smoothing=5
n Polarity=1, Orientation=1, Set Req.Image Size=No, Priority=Low
n Interceptor=Yes, N-Event-Print Job=No, N-Event Printer=No
n Trim=No, Attribute Warning=No
n Contrast Test Mode=No, Contrast Test Mode Density=0
DICOM Network
Fiber Cable
iew
00 DryV
3M 87
Fiber Cable
Note: This setup is basically also valid for 8800/8500 Dual camera
by basically using the correspondent Model into 9410 Local Printers
Note: CR always sends 2:1 format Portrait-1column-2 rows, with images 90-degree rotated,
therefore some limitations are present if the format 2:1 side by side is wished
Note: if images are printed too dark, set TFT=Siews87b.w87 to print them lighter (see below)
n Formatting: Max Img Row=0, Min Horiz Sep=9, Min Vert Sep=6
n Formatting: Trim Width when enabled=1, Trim Width when disabled=0
n Formatting: Pixel Pitch=12.8205
n Image Processing: Grayscale=On, Max Image Dmax=3.1
n SCU: Density Space= On, Perception LUT =On
n M952 Usage: Min H/V Mag=1, Max H/V Mag=64, Min Dmax 952=1.7
9410 Setup:
n on Device Setup, LOCAL PRINTERS:
n Printer=8500, Model=8500, Output=Fiber
n Baud=19200, Parity=None, Data=8, Stop=1, Command Set=Superset
n Pixel=12, Header/Line, Timeout=60, Transfer Rate=2 MHz
n Film Mismatch=Print Always, Interpolation Type=831
n Interp Num=5, Max.Density=300, Contrast=6, Border Density=0
n TFT/ULUT Emulation=On, Installed TFT/ULUT=Ver693c0.w87
n on Device Setup, SCP PRINTERS, Current Providers:
n Printer=8500, AE Title= NER_9410, Port= 1024, Max Associations= 5
n on Device Setup, SCP PRINTERS, Registered Users:
n SCU AETitle= accordingly, SCU IPAddr=accordingly, SCP=8500
n Copies=1, Contrast Table=2, TFT/ULUT= Wrkstn2a.w87 (or Siews87b.w87)
n Max.Density=300, Border Density=0, Mag.Type=8, Smoothing=5
n Polarity=1, Orientation=1, Set Req.Image Size=No, Priority=Low
n Interceptor=Yes, N-Event-Print Job=No, N-Event Printer=No
n Trim=No, Attribute Warning=No
n Contrast Test Mode=No, Contrast Test Mode Density=0
DICOM Network
RS422
COPCIL Board 9-pole Plug
Copper Cable Control 9-pin
Data 37-pin
Note: CR always sends 2:1 format Portrait-1column-2 rows, with images 90-degree rotated,
therefore some limitations are present if the format 2:1 side by side is wished
Note: if images are printed too dark, set TFT=Siews87b.w87 to print them lighter (see below)
9410 Setup:
on Device Setup, LOCAL PRINTERS:
n Printer=8100, Model=8100 4096 pxls/line, Output=Copper
n Baud=1200, Parity=Even, Data=8, Stop=1, Command Set=952
n Pixel=12, Header/Line, Timeout=60, Transfer Rate=1 MHz
n Film Mismatch=Print Always, Interpolation Type=831
n Interp Num=5, Max.Density=300, Contrast=6, Border Density=0
n TFT/ULUT Emulation=On, Installed TFT/ULUT=Ver693c0.w87
on Device Setup, SCP PRINTERS, Current Providers:
n Printer=8100, AE Title= NER_9410, Port= 1024, Max Associations= 5
on Device Setup, SCP PRINTERS, Registered Users:
n SCU AETitle= accordingly, SCU IPAddr=accordingly, SCP=8100
n Copies=1, Contrast Table=2, TFT/ULUT= Wrkstn2a.w87 (or Siews87b.w87)
n Max.Density=300, Border Density=0, Mag.Type=8, Smoothing=5
n Polarity=1, Orientation=1, Set Req.Image Size=No, Priority=Low
n Interceptor=Yes, N-Event-Print Job=No, N-Event Printer=No
n Trim=No, Attribute Warning=No
n Contrast Test Mode=No, Contrast Test Mode Density=0
DICOM Network
Data 37 pin
Note: The 9410/8300 configuration can not print the External Text Annotation Box,
in this case MIM200/8300 solve the problem ie print External Text Annotation Box
Note: CR always sends 2:1 format Portrait-1column-2 rows, with images 90-degree rotated,
therefore some limitations are present if the format 2:1 side by side is wished
Note: if images are printed too dark, set Contrast=4 to print them lighter (see below)
9410 Setup:
n on Device Setup, LOCAL PRINTERS:
n Printer=8300, Model=8300 Copper, Output=Copper
n Command Set=952, Baud=1200, Data=8, Stop=1, Parity=Even
n Pixel=8, Header/Line, Timeout=60, Transfer Rate=1 MHz
n Film Mismatch=Print Always, Interpolation Type=831
n Interp Num=0, Max.Density=300, Contrast=6, Border Density=0
n TFT/ULUT Emulation=On, Installed TFT/ULUT= upmsv3k.w8u
n on Device Setup, SCP PRINTERS, Current Providers:
n Printer=8300, AE Title= NER_9410, Port= 1024, Max Associations= 5
n on Device Setup, SCP PRINTERS, Registered Users:
n SCU AETitle= accordingly, SCU IPAddr=accordingly
n SCP=8300, Copies=1, Contrast Table=1 (or 4), TFT/ULUT= wrkstn83a.w8u
n Max.Density=300, Border Density=0, Mag.Type=8, Smoothing=0
n Polarity=1, Orientation=1, Set Req.Image Size=No, Priority=Low
n Interceptor=Yes, N-Event-Print Job=No, N-Event Printer=No
n Trim=No, Attribute Warning=No
n Contrast Test Mode=No, Contrast Test Mode Density=0
8300 Setup:
n on Operator Menu set: D=16, C=6, Sharp/Smooth=0 ie Auto
n on Operator Menu set: Film Layout: 1 on 1=Portrait
n on Service Menu set: Ratio=1.00, Serial=1200,8,1,Even,Comma,3M, Memory=16
n on Service Menu set: Digital Interface: Parity=Even, Modality Group=1
DICOM Network
190 Setup:
n On 190 Control Panel press Menu, Setup:
n Printer Density=3.00, Curve Shape=0.0, Contrast=0, Contrast Pivot Density=1.2
n IPAddress=accordingly, Subnet Mask=accordingly, Gateway Address=accordingly
n Port=5040, Network Node Name=Kodak MLP190, Connection Type=RJ45
DICOM Network
Fiber Cable
Note: CR always sends 2:1 format Portrait-1column-2 rows, with images 90-degree rotated,
therefore some limitations are present if the format 2:1 side by side is wished
MIM200 Setup:
n on Configure, Network:
n Computer Name=eg Kodak2180, IPAddr=accordingly
n Subnet Mask=accordingly, Gateway Addr=accordingly
n on Configure, Input, Network, Add:
n Protocol=DICOM 3.0, Log.Name=DICOM, Type/Com=Keypad/COM9
n on Configure, Destination, Add, Print, Direct, Qualified, KELP 2180, Set:
n General: Log.Name=KELP2180, Database Name=KELP 2180
n General: Model=KELP 2180, Memory=24, Node ID=6 or accordingly
n Media Info: Media=35x43cm, 4136x5160, 5030, (Blue)
n Media Info:Media=35x35cm,4136x4136,4006, (Blue)
n Media Info: Media=11x14in, 3240x4136, 4006, (Blue)
n Media Info: Media=8x10in, 2290x2840, 2710, (Blue)
n Supported Item: Collation=On, Text=On, Tonescaling=On, Rotation=On
n Interpolation: NoMag=On, Bil=On, Repl=On,Cubic=On, Cubic 2=On
n Format Types: Custom=On, Slide=On, Row Symmetric=On
n Format Types: 1, 2, 4, 6, 8, 9, 12, 15, 16, 20, 24, 30, 35=On
n Formatting: Aspect Ratio Mix Page=On, Image Size Mix in Std Fmt=On
n Formatting: DICOM Annotation Box=On, Req.Size Scale=On
n Formatting: Req.Size Mix in Row=On, Trim=On
n Formatting: Aspect Ratio Mix in Row=On, Image Size Mix in Row=On
n Formatting: Req.Image Size=On, Req.Size Mix on Page=On
n Formatting: True Landscape=On
n Formatting: Max Img Band=20, Max Band per Page=20, Max Img Col=0
n Formatting: Max Img Row=0, Min Horiz Sep=2, Min Vert Sep=2
n Formatting: Trim Width Enabled=2, Trim Width Disabled=2
n Formatting: Pixel Pitch=12.6582
n Image Processing: Grayscale=On, Minify=On, Max Image Dmax=3.2
n M952 Usage: Min H/V Mag=0, Max H/V Mag=0, Min Dmax 952=1.7
n on Configure, SCP Services, select the specific modality, Modify:
n PLUT=N, ToneScaling=Curve Shape (Always=Y)
n Curve Shape=0 (Always=Y), Contrast (wet)=0 (Always=Y)
n Image Dmin=0.00 (Always=N), Image Dmax=3.00 (Always=N)
n NeventReports=Off (Always=Y), Warning Status=On
n Print Date=Off, Print Time=Off, Page Number=Off, Hosp.Name=Off
n Modality ID=Off, Annotation Override=Off (Always=N)
n Minify/Scale=On, Crop=Off, Text Box Relocation=None
n Print Priority=Normal (Always=N), Image Polarity=Normal (Always=N)
n Interpolation=Cubic,
n Border=Black (Always=N), Film Base=Blue Film (Always=N)
n Film Size=14INx17IN (Always=N), Film Output Dest=Bin 9 (Always=N)
n Negotiate Color Print=Off
2180 Setup:
n Optical Interface board will automatic configure into 2180, no setup needed
DICOM Network
Note: CR always sends 2:1 format Portrait-1column-2 rows, with images 90-degree rotated,
therefore some limitations are present if the format 2:1 side by side is wished
MIM200 Setup:
n on Configure, Network:
n Computer Name=eg Kodak160, IPAddr=accordingly
n Subnet Mask=accordingly, Gateway Addr=accordingly
n on Configure, Input, Network, Add:
n Protocol=DICOM 3.0, Log.Name=DICOM, Type/Com=Keypad/COM9
n on Configure, Destination, Add, Print, Direct, Qualified, KELI 160, Set:
n General: Log.Name=KELI 160, IPAddr=100.100.100.30,
n General: Database Name=KELI 160, Model=KELI 160
n Media Info: Media=35x43cm, 4361x5348, 5228, Any (Blue,Clear)
n Supported Item: Collation=On, Text=On, Tonescaling on Image=On
n Supported Item: Pivot Density=On, Rotation=On
n Interpolation: NoMag=On, Bil=On, Repl=On,Cubic=On, Cubic 2=On
n Format Types: Custom=On, Slide=On, Row Symmetric=On
n Format Types: 1, 2, 4, 6, 8, 9, 12, 15, 16, 20, 24, 30, 35=On
n Formatting: Aspect Ratio Mix Page=On, Image Size Mix in Std Fmt=On
n Formatting: DICOM Annotation Box=On, Req.Size Scale=On
n Formatting: Req.Size Mix in Row=On, Trim=On
n Formatting: Aspect Ratio Mix in Row=On, Image Size Mix in Row=On
n Formatting: Req.Image Size=On, Req.Size Mix on Page=On
n Formatting: True Landscape=On
n Formatting: Max Img Band=20, Max Band per Page=20, Max Img Col=0
n Formatting: Max Img Row=0, Min Horiz Sep=2, Min Vert Sep=2
n Formatting: Trim Width Enabled=2, Trim Width Disabled=0
n Formatting: Pixel Pitch=12.8
n Image Processing: Grayscale=On, Minify=On, Max Image Dmax=3.2
n M952 Usage: Min H/V Mag=0, Max H/V Mag=0, Min Dmax 952=1.7
n on Configure, SCP Services, select the specific modality, Modify:
n PLUT=N, ToneScaling=Curve Shape (Always=Y)
n Curve Shape= 0 (Always=Y), Contrast (wet)=0 (Always=Y)
n Image Dmin=0.00 (Always=N), Image Dmax=3.00 (Always=N)
n NeventReports=Off (Always=Y), Warning Status=On
n Print Date=Off, Print Time=Off, Page Number=Off, Hosp.Name=Off
n Modality ID=Off, Annotation Override=Off (Always=N)
n Print Priority=Normal (Always=N), Image Polarity=Normal (Always=N)
n Interpolation=Cubic, Border=Black (Always=N)
n Film Base=Blue Film (Always=N), Film Size=14INx17IN (Always=N)
n Negotiate Color Print=Off
DICOM Network
yView
00 Dr
3M 87
Fiber Cable
Fiber Cable
n Formatting: Aspect Ratio Mix Page=On, Image Size Mix in Std Fmt=On
n Formatting: DICOM Annotation Box=On
n Formatting: Req.Size Scale=On, Req.Size Mix in Row=On, Trim=On
n Formatting: Aspect Ratio Mix in Row=On, Image Size Mix in Row=On
n Formatting: Req.Image Size=On, Req.Size Mix on Page=On
n Formatting: True Landscape=On
n Formatting: Max Img Band=20, Max Band per Page=20, Max Img Col=0
n Formatting: Max Img Row=0, Min Horiz Sep=2, Min Vert Sep=2
n Formatting: Trim Width when enabled=2, Trim Width when disabled=0
n Formatting: Pixel Pitch=12.8205
n Image Processing: Grayscale=On, Minify=On, Max Image Dmax=3.1
n SCU: Density Space= On, Perception LUT =On
n M952 Usage: Min H/V Mag=1, Max H/V Mag=64, Min Dmax 952=1.7
MIM200 Setup:
n on Configure, Network:
n Node Name=MIM, IPAddr=accordingly
n Subnet Mask=accordingly, Gateway Addr=accordingly
n on Configure, Input, Network, Add:
n Protocol=DICOM 3.0, Log.Name=DICOM, Type/Com=Keypad/COM9
n on Configure, Destination, Add, Print, Direct, Qualified, 8700, Set:
n General: Log.Name=8700
n General: Database Name=8700, Model=8700, Memory=32
n Media Info: Media=35x43cm, 4096x5223, 5133, Blue
n Output Params: Cmd=SuperSet,Baud=19200,Data=8,Stop=1,Parity=None
n Output Params: Pixel=12, Header/Line, Transfer=2000 KHz, Acq=60
n Supported Item: Collation=On, Text=On, Tonescaling=On, Rotation=On
n Interpolation: NoMag=On, Bilin=On, Repl=On,Cubic Spline=On
n Format Types: Custom=On, Slide=On, Row Symmetric=On
n Format Types: 1, 2, 4, 6, 8, 9, 12, 15, 16, 20, 24, 30, 35=On
n Formatting: Aspect Ratio Mix Page=On, Image Size Mix in Std Fmt=On
n Formatting: DICOM Annotation Box=On, Req.Size Scale=On
n Formatting: Req.Size Mix in Row=On, Trim=On
n Formatting: Aspect Ratio Mix in Row=On, Image Size Mix in Row=On
n Formatting: Req.Image Size=On, Req.Size Mix on Page=On
n Formatting: True Landscape=On
n Formatting: Max Img Band=20, Max Band per Page=20, Max Img Col=0
n Formatting: Max Img Row=0, Min Horiz Sep=2, Min Vert Sep=2
n Formatting: Trim Width Enabled=2, Trim Width Disabled=0
n Formatting: Pixel Pitch=12.8205
n Image Processing: Grayscale=On, Minify=On, Max Image Dmax=3.1
n M952 Usage: Min H/V Mag=1, Max H/V Mag=64, Min Dmax 952=1.7
n on Configure, SCP Services, select the specific modality, Modify:
n PLUT=N, ToneScaling=PerceptionLUT (Always=Y)
n TFT/ULUT= Wrkstn2a.w87 (or Siews87b.w87) (Always=Y)
n Contrast (dry)=2 (Always=N)
n Image Dmin=0.00 (Always=N), Image Dmax=3.00 (Always=N)
n NeventReports=Off (Always=Y), Warning Status=On
n Print Date=Off, Print Time=Off, Page Number=Off, Hosp.Name=Off
DICOM Network
yView
00 Dr
3M 87
Fiber Cable
Fiber Cable
n Formatting: Aspect Ratio Mix Page=On, Image Size Mix in Std Fmt=On
n Formatting: DICOM Annotation Box=On
n Formatting: Req.Size Scale=On, Req.Size Mix in Row=On, Trim=On
n Formatting: Aspect Ratio Mix in Row=On, Image Size Mix in Row=On
n Formatting: Req.Image Size=On, Req.Size Mix on Page=On
n Formatting: True Landscape=On
n Formatting: Max Img Band=4, Max Band per Page=20, Max Img Col=0
n Formatting: Max Img Row=0, Min Horiz Sep=2, Min Vert Sep=2
n Formatting: Trim Width when enabled=2, Trim Width when disabled=0
n Formatting: Pixel Pitch=12.8205
n Image Processing: Grayscale=On, Minify=On, Max Image Dmax=3.1
n SCU: Density Space= On, Perception LUT =On
n M952 Usage: Min H/V Mag=1, Max H/V Mag=64, Min Dmax 952=1.7
MIM200 Setup:
n on Configure, Network:
n Node Name=MIM, IPAddr=accordingly
n Subnet Mask=accordingly, Gateway Addr=accordingly
n on Configure, Input, Network, Add:
n Protocol=DICOM 3.0, Log.Name=DICOM, Type/Com=Keypad/COM9
n on Configure, Destination, Add, Print, Direct, Qualified, 8500, Set:
n General: Log.Name=8500
n General: Database Name=8500, Model=8500, Memory=32
n Media Info: Media=11x14in, 3388x4283, 4193, Blue
n Output Params: Cmd=SuperSet,Baud=19200,Data=8,Stop=1,Parity=None
n Output Params: Pixel=12, Header/Line, Transfer=2000 KHz, Acq=60
n Supported Item: Collation=On, Text=On, Tonescaling=On, Rotation=On
n Interpolation: NoMag=On, Bilin=On, Repl=On,Cubic Spline=On
n Format Types: Custom=On, Slide=On, Row Symmetric=On
n Format Types: 1, 2, 4, 6, 8, 9, 12, 15, 16, 20, 24, 30, 35=On
n Formatting: Aspect Ratio Mix Page=On, Image Size Mix in Std Fmt=On
n Formatting: DICOM Annotation Box=On, Req.Size Scale=On
n Formatting: Req.Size Mix in Row=On, Trim=On
n Formatting: Aspect Ratio Mix in Row=On, Image Size Mix in Row=On
n Formatting: Req.Image Size=On, Req.Size Mix on Page=On
n Formatting: True Landscape=On
n Formatting: Max Img Band=20, Max Band per Page=20, Max Img Col=0
n Formatting: Max Img Row=0, Min Horiz Sep=2, Min Vert Sep=2
n Formatting: Trim Width Enabled=2, Trim Width Disabled=0
n Formatting: Pixel Pitch=12.8205
n Image Processing: Grayscale=On, Minify=On, Max Image Dmax=3.1
n M952 Usage: Min H/V Mag=1, Max H/V Mag=64, Min Dmax 952=1.7
n on Configure, SCP Services, select the specific modality, Modify:
n PLUT=N, ToneScaling=PerceptionLUT (Always=Y)
n TFT/ULUT= Wrkstn2a.w87 (or Siews87b.w87) (Always=Y)
n Contrast (dry)=2 (Always=N)
n Image Dmin=0.00 (Always=N), Image Dmax=3.00 (Always=N)
n NeventReports=Off (Always=Y), Warning Status=On
n Print Date=Off, Print Time=Off, Page Number=Off, Hosp.Name=Off
DICOM Network
RS422
COPCIL Board 9-pole Plug
Copper Cable Control 9-pin
Data 37-pin
MIM200 Setup:
n on Configure, Network:
n Node Name=MIM, IPAddr=accordingly
n Subnet Mask=accordingly, Gateway Addr=accordingly
n on Configure, Input, Network, Add:
n Protocol=DICOM 3.0, Log.Name=DICOM, Type/Com=Keypad/COM9
n on Configure, Destination, Add, Print, Direct, Qualified, 8100, Set:
n General: Log.Name=8100
n General: Database Name=8100, Model=8100, Memory=32
n Media Info: Media=35x43cm, 4096x5223, 5133, Blue
n Output Params: Cmd Set=952, Baud=1200, Data=8, Stop=1, Parity=Even
n Output Params: Pixel=12, Header/Line, Transfer=1000 KHz, Acquire=60
n Supported Item: Collation=On, Text=On, Tonescaling=On, Rotation=On
n Interpolation: NoMag=On, Bilin=On, Repl=On,Cubic Spline=On
n Format Types: Custom=On, Slide=On, Row Symmetric=On
n Format Types: 1, 2, 4, 6, 8, 9, 12, 15, 16, 20, 24, 30, 35=On
n Formatting: Aspect Ratio Mix Page=On, Image Size Mix in Std Fmt=On
n Formatting: DICOM Annotation Box=On, Req.Size Scale=On
n Formatting: Req.Size Mix in Row=On, Trim=On
n Formatting: Aspect Ratio Mix in Row=On, Image Size Mix in Row=On
n Formatting: Req.Image Size=On, Req.Size Mix on Page=On
n Formatting: True Landscape=On
n Formatting: Max Img Band=20, Max Band per Page=20, Max Img Col=0
n Formatting: Max Img Row=0, Min Horiz Sep=2, Min Vert Sep=2
n Formatting: Trim Width Enabled=2, Trim Width Disabled=0
n Formatting: Pixel Pitch=12.8205
n Image Processing: Grayscale=On, Minify=On, Max Image Dmax=3.1
n M952 Usage: Min H/V Mag=1, Max H/V Mag=64, Min Dmax 952=1.7
n on Configure, SCP Services, select the specific modality, Modify:
n PLUT=N, ToneScaling=PerceptionLUT (Always=Y)
n TFT/ULUT= Wrkstn2a.w87 (or Siews87b.w87) (Always=Y)
n Contrast (dry)=2 (Always=N)
n Image Dmin=0.00 (Always=N), Image Dmax=3.00 (Always=N)
n NeventReports=Off (Always=Y), Warning Status=On
n Print Date=Off, Print Time=Off, Page Number=Off, Hosp.Name=Off
n Modality ID=Off, Annotation Override=Off (Always=N)
n Print Priority=Normal (Always=N), Image Polarity=Normal (Always=N)
n Smoothing Type=5 (Always=N)
DICOM Network
Control 9 pin
COPCIL board
Copper Cable
Data 37 pin
MIM200 Setup:
n on Configure, Network:
n Node Name=MIM, IPAddr=accordingly
n Subnet Mask=accordingly, Gateway Addr=accordingly
n on Configure, Input, Network, Add:
n Protocol=DICOM 3.0, Log.Name=DICOM, Type/Com=Keypad/COM9
n on Configure, Destination, Add, Print, Direct, Qualified, 8300, Set:
n General: Log.Name=8300
n General: Database Name=8300, Model=8300, Memory=32
n Media Info: Media=8x10in, 2256x2676, 2596, Blue
n Output Params: Cmd Set=952, Baud=1200, Data=8, Stop=1, Parity=Even
n Output Params: Pixel=8, Header/Line, Transfer=2000 KHz, Acquire=60
n Supported Item: Collation=On, Text=On, Tonescaling=On, Rotation=On
n Interpolation: NoMag=On, Bilin=On, Repl=On,Cubic Spline=On
n Format Types: Custom=On, Slide=On, Row Symmetric=On, SuperSlide=On
n Format Types: 1, 2, 4, 6, 8, 9, 12, 15, 16, 20, 24, 30, 35=On
n Formatting: Aspect Ratio Mix on Page=On, Image Size Mix in Std Fmt=On
n Formatting: DICOM Annotation Box=On, Req.Size Scale=On
n Formatting: Req.Size Mix in Row=On, Trim=On
n Formatting: Aspect Ratio Mix in Row=On, Image Size Mix in Row=On
n Formatting: Req.Image Size=On, Req.Size Mix on Page=On
n Formatting: True Landscape=On
n Formatting: Max Img per Band=20, Max Band per Page=20, Max Img Col=0
n Formatting: Max Img Row=0, Min Horiz Sep=2, Min Vert Sep=2
n Formatting: Trim Width Enabled=2, Trim Width Disabled=0
n Formatting: Pixel Pitch=11.811
n Image Processing: Grayscale=On, Minify=On, Max Image Dmax=3
n M952 Usage: Min H/V Mag=1, Max H/V Mag=16, Min Dmax 952=1.5
n on Configure, SCP Services, select the specific modality, Modify:
n PLUT=N, ToneScaling=PerceptionLUT (Always=Y)
n TFT/ULUT= wkstn83a.w8u (Always=Y), Contrast (dry)=1 (or 4) (Always=N)
n Image Dmin=0.00 (Always=N), Image Dmax=3.00 (Always=N)
n NeventReports=Off (Always=Y), Warning Status=On
n Print Date=Off, Print Time=Off, Page Number=Off, Hosp.Name=Off
n Modality ID=Off, Annotation Override=Off (Always=N)
n Print Priority=Normal (Always=N), Image Polarity=Normal (Always=N)
n Smoothing Type=2 (Always=N)
n Border=Black (Always=N), Film Base=Blue Film (Always=N)
8300 Setup:
n on Operator Menu set: D=16, C=6, Sharp/Smooth=0 ie Auto
n on Operator Menu set: Film Layout: 1 on 1=Portrait
n on Service Menu set: Ratio=1.00, Serial=1200,8,1,Even,Comma,3M, Memory=16
n on Service Menu set: Digital Interface: Parity=Even, Modality Group=1
DICOM Network
Data 37 pin
MIM200 Setup:
n on Configure, Network:
n Node Name=MIM, IPAddr=accordingly
n Subnet Mask=accordingly, Gateway Addr=accordingly
n on Configure, Input, Network, Add:
n Protocol=DICOM 3.0, Log.Name=DICOM, Type/Com=Keypad/COM9
n on Configure, Destination, Add, Print, Direct, Qualified, 8610 (or 8600), Set:
n General: Log.Name=8610 (or 8600),
n General: Database=8610 (or 8600), Model=8610 (or 8600), Memory=32
n Media Info: Media=8x10in, 5025x6200, 6020, Blue
n Output Params: Cmd Set=952, Baud=1200, Data=8, Stop=1, Parity=Even
n Output Params: Pixel=12 (8 if 8600), Header/Line, Transfer=2000,Acq=60
n Supported Item: Collation=On, Text=On, Tonescaling=On, Rotation=On
n Interpolation: NoMag=On, Bilin=On, Repl=On,Cubic Spline=On
n Format Types: Custom=On, Slide=On, Row Symmetric=On
n Format Types: 1, 2, 4, 6, 8, 9, 12, 15, 16, 20, 24, 30, 35=On
n Formatting: Aspect Ratio Mix Page=On, Image Size Mix in Std Fmt=On
n Formatting: DICOM Annotation Box=On, Req.Size Scale=On
n Formatting: Req.Size Mix in Row=On, Trim=On
n Formatting: Aspect Ratio Mix in Row=On, Image Size Mix in Row=On
n Formatting: Req.Image Size=On, Req.Size Mix on Page=On
n Formatting: True Landscape=On
n Formatting: Max Img Band=20, Max Band per Page=20, Max Img Col=0
n Formatting: Max Img Row=0, Min Horiz Sep=2, Min Vert Sep=2
n Formatting: Trim Width Enabled=2, Trim Width Disabled=0
n Formatting: Pixel Pitch=25.8065
n Image Processing: Grayscale=On, Minify=On, Max Image Dmax=3.5
n M952 Usage: Min H/V Mag=0.26, Max H/V Mag=16, Min Dmax 952=2
n on Configure, SCP Services, select the specific modality, Modify:
n PLUT=N, ToneScaling=PerceptionLUT (Always=Y)
n TFT/ULUT= upmsv3kp.w8u (Always=N), Contrast (dry)=6 (Always=Y)
n Modality Group=1, Conv.Group=1, Gamma Table=Linear in Density
n Image Dmin=0.00 (Always=N), Image Dmax=3.50 (Always=Y)
n Smoothing Type=1 (Always=Y), Image Polarity=Normal (Always=N)
n NeventReports=Off (Always=Y), Warning Status=On
n Print Date=Off, Print Time=Off, Page Number=Off, Hosp.Name=Off
8610 Setup: on 8610 Operator Menu into Test Menu, Software Version, verify:
n Imager=2.4, VRTX32=1.08, Contrast=6.P.2, Conv.Kernel=M.1.0
n (if 8600: Imager=2.5, Contrast=6.G.7, Conv.Kernel=1.0.5)
n on 8610 Operator Menu into Configure User set:
n Density=16, Contrast=6, Sharp/Smooth=1, Film Layout: 1 on 1=Portrait
n Gamma= Xmittance, Image Size=Scale To Fit, Detector Size= don’t care
n on 8610 Service Menu into Configure User set:
n Ratio=1.00, Serial Control Intf.=1200,8,1,Even,Comma,3M, Memory=127
n Digital Interface: Parity=Even, Modality Group=1, Smoothing Group=1
DICOM Network
Crossed
Network Cable
MIM200 Setup:
n on Configure, Network:
n Node Name=MIM, IPAddr=accordingly
n Subnet Mask=accordingly, Gateway Addr=accordingly
n on Configure, Input, Network, Add:
n Protocol=DICOM 3.0, Log.Name=DICOM, Type/Com=Keypad/COM9
n on Configure, Destination, Add, Print, Direct, Qualified, 8200, Set:
n General: Log.Name=8200, IPAddr=100.100.100.40,
n General: Database Name=8200, Model=8200, Memory=32
n Media Info: Media=35x43cm, 4361x5223, 5133, Any (Blue,Clear)
n Media Info: Media=35x35cm, 4361x4247, 4157, Any (Blue,Clear)
n Media Info: Media=11x14in, 3272x4361, 4271, Any (Blue,Clear)
n Supported Item: Collation=On, Common Text=On, Tonescaling=On
n Supported Item: Remote Image Deletion=On, Rotation=On
n Interpolation: No Magnification=On, Bilin=On, Repl=On
n Interpolation: Cubic Spline=On, Cubic Convolution 2=On
n Format Types: Custom=On, Row Symmetric=On
n Format Types: 1, 2, 4, 6, 8, 9, 12, 15, 16, 20, 24, 30, 35=On
n Formatting: Aspect Ratio Mix Page=On, Image Size Mix in Std Fmt=On
n Formatting: DICOM Annotation Box=On, Req.Size Scale=On
n Formatting: Req.Size Mix in Row=On, Trim=On
n Formatting: Aspect Ratio Mix in Row=On, Image Size Mix in Row=On
n Formatting: Req.Image Size=On, Req.Size Mix on Page=On
n Formatting: True Landscape=On
n Formatting: Max Img Band=20, Max Band per Page=20, Max Img Col=0
n Formatting: Max Img Row=0, Min Horiz Sep=2, Min Vert Sep=2
n Formatting: Trim Width Enabled=2, Trim Width Disabled=0
n Formatting: Pixel Pitch=12.8205
n Image Processing: Grayscale=On, Minify=On, Max Image Dmax=3.1
n SCU: Density Space= On, Variable Border=On, PLUT Service= On
n SCU: Curve Shape Tonescaling=On, Perception LUT Tonescaling=On
n M952 Usage: Min H/V Mag=1, Max H/V Mag=64, Min Dmax 952=1.7
n on Configure, SCP Services, select the specific modality, Modify:
n PLUT=N, ToneScaling=PerceptionLUT (Always=Y)
n TFT/ULUT= Wrkstn2a.w87 (or Siews87b.w87) (Always=Y)
n Contrast (dry)=2 (Always=N)
8900 Setup:
n on Configuration, System, Network:
n Host Name=DV8900, IPAddr=accordingly
n Subnet Mask=accordingly, Gateway Addr=accordingly
n on Configuration, DICOM SCP, Communications:
n Port=5040, Association Limit=12, Source Name=DICOM
n on Configuration, Destination:
n General: Log.Name=8900
n Media Types: Media=35x43cm, 9100x11037, 10781, Any
n Media Types: Media=35x35cm,9100x9087, 8831, Any
n Media Types: Media=11x14in, 7137x9100, 8844, Any
n Media Types: Media=10x12in, 6490x7767, 7511, Any
n Media Types: Media=8x10in, 5167x6490, 6234, Any
n Formatting: Aspect Ratio Mix Page=On, Aspect Ratio Mix Row=On
n Formatting: Image Size Mix in Std Fmt=On, Image Size Mix Row=On
n Formatting: DICOM Annotation Box=On, Req.Image Size=On
n Formatting: Req.Size Scale=On, Req.Size Mix Page=On
n Formatting: Req.Size Mix Row=On, Trim=On,
n Formatting: True Landscape=On, Rotation=On
n Formatting: Minify/Crop=On, Tonescaling on Image Basis=On
n Formatting: Max Img Band=7, Max Band Page=7, Max Img Cols=0
n Formatting: Max Img Rows=0, Pixel Pitch=25.5910, Min Horiz Sep=4
n Formatting: Min Vert Sep=4, Trim Width Enabled=4
n Formatting: Trim Width Disabled=0, Maximum DMAX=3.30
n on Configuration, DICOM SCP, SCP Services, select specific modality, Modify:
n Negotiate Presentation LUT=No, Negotiate Color Print=No
n TFT= Wrkstn2a.w87 (or Siews87b.w87) (Always=N)
n Contrast=2 (Always=N)
n Smoothing Type=5 (Always=N), Image Polarity (Always=N)
n Image Dmin=0.00 (Always=N), Image Dmax=3.00 (Always=N)
n NeventReports=No (Always=Y), Warnings=Yes
n Print Priority=Normal (Always=N), Border=3.99 (Always=N)
DICOM Network
8150 Setup:
n on Configuration, System, Network:
n Host Name=DV8150DRE, IPAddr=accordingly
n Subnet Mask=accordingly, Gateway Addr=accordingly
n on Configuration, DICOM SCP, Communications:
n Port=5040, Association Limit=12, Source Name=DICOM
n on Configuration, Destination:
n AE Title: Log.Name=DV8150
n Media Types: Media=35x43cm, 4438x5390, 5262, Any
n Media Types: Media=35x35cm, 4438x4414,4286, Any
n Media Types: Media=11x14in, 3440x4438, 4310, Any
n Formatting: Aspect Ratio Mix Page=On, Aspect Ratio Mix Row=On
n Formatting: Image Size Mix in Std Fmt=On, Image Size Mix Row=On
n Formatting: DICOM Annotation Box=On, Req.Image Size=On
n Formatting: Req.Size Scale=On, Req.Size Mix Page=On
n Formatting: Req.Size Mix Row=On, Trim=On,
n Formatting: True Landscape=On, Rotation=On
n Formatting: Minify/Crop=On, Tonescaling on Image Basis=On
n Formatting: Max Img Band=7, Max Band Page=7, Max Img Cols=0
n Formatting: Max Img Rows=0, Pixel Pitch=12.8000, Min Horiz Sep=2
n Formatting: Min Vert Sep=2, Trim Width Enabled=2
n Formatting: Trim Width Disabled=0, Maximum DMAX=3.10
n on Configuration, DICOM SCP, SCP Services, select specific modality, Modify:
n Negotiate Presentation LUT=No, Negotiate Color Print=No,
n TFT Set Name=Wrkstn2a.w87 (Always=Y)
n Contrast=1 (Always=N), Smoothing Type=5 (Always=N)
n Dmin=0.00 (Always=N), Dmax=3.00 (Always=N)
n Image Polarity=Normal (Always=N)
n NeventReports=No (Always=Y), Warnings=Yes
n Print Priority=Normal (Always=N), Border=3.99 (Always=N)
n 2mm Border=Yes, Film Clip Border=No,
n Film Base=Blue Film (Always=N), Film Size=14INx17IN (Always=N)
n Print Date=No, Print Time=No, Page Nbr=No, Hosp.Name=No,
n Modality ID=No, Annotation Override=No, Density Patch=No
n Image Resizing=Minify/Scale (Always=N),
n Text Box Location=None, Source ID=cr
DICOM Network
Kodak DirectView CR
n M952 Usage: Min H/V Mag=1, Max H/V Mag=16, Min Dmax 952=1.5
CMI-1000 Setup:
at Local Panel, under Media, set A4 or Letter ie what inside Paper Tray
(CMI-1000 sw considers only this field and uses it as A4 or Letter (Always=Y):
at Local Panel, under Menu, Imager Setup:
n Network Setup:
n IPAddr=accordingly, Subnet Mask=accordingly, Gateway=accordingly
n under More Settings: DICOM Port=5040
n Edit Host Name/AE Title=CMI1000
n Modality (SCU) Config (or after modality recognition):
n Select Modality=accordingly, Modality Config.Assistant=Yes, Reset Config=No
n Note: Color IQ settings used when images sent with Color DICOM SOP
n under Image Quality, Color Image Quality: (no need to adjust, leave defaults)
n Match Monitor Colors=default ie sRGB Color Space Profile.icm
n Adjust Color Tones=default ie Default_Contrast_100.icm
n Note: Grayscale IQ settings used when images sent with Grayscale DICOM SOP:
n under Image Quality, Grayscale Image Quality:
n Contrast=7 (Always=Y)
n TFT Set (From list)=Wrkstn2a.w87 (Always=Y)
n Wet Contrast=0 (Always=N), Curve Shape=429 (Always=N)
n under More Quality Settings:
n Tonescaling=Presentation LUT (Always=N),
n Image Dmax=220 (Always=N), Image Dmin=10 (Always=N)
n Smoothing=11 (Always=Y), Polarity=Positive (Always=N)
n Interpolation=CUBIC (Always=N), Trim=No (Always=N)
n Page Orientation=PORTRAIT (Always=N), Negotiate PLUT=No
n under Modality Defaults:
n Media Size=8.5x11 (Always=N), don’t care, this field plays no role
n Image Resizing=Minify (Always=N),
n Priority=Normal (Always=N), NeventReports=No (Always=Y),
n Warnings=Yes, Color=Yes
n (set Color=No when only b/w images are printed and set it to be sure
n to apply to the b/w images the Greyscale Image Quality settings)
n Page Annotation:
n Hosp.Name=No, Modality ID=No, Page Nbr=No, Date=No, Time= No
n Save Changes and Exit
1
Setup valid also for Kodak PACS LINK 25 PRINT SERVER.
Data 37 pin
n M952 Usage: Min H/V Mag=0.26, Max H/V Mag=16, Min Dmax 952=2
MIM200 Setup:
n on Configure, Network: Node Name=MIM, IPAddr=accordingly,
n Subnet Mask=accordingly, Gateway Addr=accordingly
n on Configure, Input, Network, Add:
n Protocol=DICOM 3.0, Log.Name=DICOM, Type/Com=Keypad/COM9
n on Configure, Destination, Add, Print, Direct, Qualified, 8610, Set:
n General: Log.Name=8610,Database=8610,Model=8610,Memory=32
n Media Info: Media=8x10in, 5025x6200, 6020, Blue
n Output Params: Cmd Set=952, Baud=1200, Data=8, Stop=1, Parity=Even
n Output Params: Pixel=12, Header/Line, Transfer=2000,Acq=60
n Supported Item: Collation=On, Text=On, Tonescaling=On, Rotation=On
n Interpolation: NoMag=On, Bilin=On, Repl=On,Cubic Spline=On
n Format Types: Custom=On, Slide=On, Row Symmetric=On
n Format Types: 1, 2, 4, 6, 8, 9, 12, 15, 16, 20, 24, 30, 35=On
n Formatting: Aspect Ratio Mix Page=On, Image Size Mix in Std Fmt=On
n Formatting: DICOM Annotation Box=On, Req.Size Scale=On
n Formatting: Req.Size Mix Row=On, Trim=On, True Landscape=On
n Formatting: Aspect Ratio Mix in Row=On, Image Size Mix in Row=On
n Formatting: Req.Image Size=On, Req.Size Mix on Page=On
n Formatting: Max Img Band=20, Max Band per Page=20, Max Img Col=0
n Formatting: Max Img Row=0, Min Horiz Sep=2, Min Vert Sep=2
n Formatting: Trim Width Enabled=2, Trim Width Disabled=0
n Formatting: Pixel Pitch=25.8065
n Image Processing: Grayscale=On, Minify=On, Max Image Dmax=3.5
n M952 Usage: Min H/V Mag=0.26, Max H/V Mag=16, Min Dmax 952=2
n on Configure, SCP Services, select the specific modality, Modify:
n PLUT=N, ToneScaling=PerceptionLUT (Always=Y)
n Contrast (dry)=6 (Always=Y)
n Modality Group=1 (which corresponds to TFT/ULUT=upmsv3kp.w8u),
n Conv.Group=1, Gamma Table=Linear in Density
n Image Dmin=0.00 (Always=N), Image Dmax=3.50 (Always=Y)
n Smoothing Type=1 (Always=Y), Image Polarity=Normal (Always=N)
n NeventReports=Off (Always=Y), Warning Status=On
n Print Date=Off, Print Time=Off, Page Number=Off, Hosp.Name=Off
n Modality ID=Off, Annotation Override=Off (Always=N)
n Minify/Scale=On, Crop=Off, Text Box Relocation=None
n Print Priority=Normal (Always=N), Border=3.99 (Always=N)
n Film Base=Blue Film (Always=N), Film Size=8INx10IN (Always=N)
8610 Setup: on 8610 Operator Menu into Test Menu, Software Version, verify:
n Imager=2.4, VRTX32=1.08, Contrast=6.P.2, Conv.Kernel=M.1.0
n on 8610 Operator Menu into Configure User set:
n Density=16, Contrast=6, Sharp/Smooth=1, Film Layout: 1 on 1=Portrait
n Gamma= Xmittance, Image Size=Scale To Fit, Detector Size= don’t care
n on 8610 Service Menu into Configure User set:
n Ratio=1.00, Serial=1200,8,1,Even,Comma,3M, Memory=127 (or 255)
n Digital Interface: Parity=Even, Modality Group=1, Smoothing Group=1
DICOM Network
8900 Setup:
n on Configuration, System, Network:
n Host Name=DV8900, IPAddr=accordingly
n Subnet Mask=accordingly, Gateway Addr= accordingly
n on Configuration, System, Software License:
n License Status=Mammo Key is ON
n on Configuration, DICOM SCP, Communications:
n Port=5040, Association Limit=12, Source Name=DICOM
n on Configuration, Destination:
n General: Log.Name=8900
n Media Types: Media=35x43cm, 9100x11037, 10781, Any
n Media Types: Media=35x35cm,9100x9087, 8831, Any
n Media Types: Media=11x14in, 7137x9100, 8844, Any
n Media Types: Media=10x12in, 6490x7767, 7511, Any
n Media Types: Media=8x10in, 5167x6490, 6234, Any
n Formatting: Aspect Ratio Mix Page=On, Aspect Ratio Mix Row=On
n Formatting: Image Size Mix in Std Fmt=On, Image Size Mix Row=On
n Formatting: DICOM Annotation Box=On, Req.Image Size=On
n Formatting: Req.Size Scale=On, Req.Size Mix Page=On
n Formatting: Req.Size Mix Row=On, Trim=On,
n Formatting: True Landscape=On, Rotation=On
n Formatting: Minify/Crop=On, Tonescaling on Image Basis=On
n Formatting: Max Img Band=7, Max Band Page=7, Max Img Cols=0
n Formatting: Max Img Rows=0, Pixel Pitch=25.5910, Min Horiz Sep=4
n Formatting: Min Vert Sep=4, Trim Width Enabled=4
n Formatting: Trim Width Disabled=0, Maximum DMAX=3.30
n on Configuration, DICOM SCP, SCP Services, select specific modality, Modify:
n Negotiate Presentation LUT=No, Negotiate Color Print=No
n TFT= Wrkstn2a.w87 (Always=Y), Contrast=1 (Always=Y)
1
Setup valid also for Kodak PACS LINK 25 PRINT SERVER.
DICOM Network
iew
00 DryV
3M 87
Kodak DirectView
Fiber Cable
-DR 5000
-DR 9000
Fiber Cable
Note: This setup is basically also valid for 8800/8700 Dual and HQ cameras
by basically using the correspondent Model into 9410 Local Printers
Note: The 9410/8700 configuration can not print some formats (eg 2:1 side by side, etc),
in this case the MIM200/8700 solve the problem ie print formats 2:1 side by side, etc
9410 Setup:
n on Device Setup, LOCAL PRINTERS:
n Printer=8700, Model=8700, Output=Fiber
n Baud=19200, Parity=None, Data=8, Stop=1, Command Set=Superset
n Pixel=12, Header/Line, Timeout=60, Transfer Rate=2 MHz
n Film Mismatch=Print Always, Interpolation Type=831
n Interp Num=11 Max.Density=300, Contrast=6, Border Density=0
n TFT/ULUT Emulation=On, Installed TFT/ULUT=Ver693c0.w87
n on Device Setup, SCP PRINTERS, Current Providers:
n Printer=8700, AE Title=9410, Port=1024, Max Associations=5
n on Device Setup, SCP PRINTERS, Registered Users:
n SCU AETitle=accordingly, SCU IPAddr=accordingly, SCP=8700
n Copies=1, Contrast Table=2, TFT/ULUT=Wrkstn2a.w87
n Max.Density=300, Border Density=0, Mag.Type=8, Smoothing=11
n Polarity=1, Orientation=1, Set Req.Image Size=No, Priority=Low
n Interceptor=Yes, N-Event-Print Job=No, N-Event Printer=No
n Trim=No, Attribute Warning=No
n Contrast Test Mode=No, Contrast Test Mode Density=0
DICOM Network
iew
00 DryV
3M 87
Kodak DirectView
Fiber Cable
-DR 5000
-DR 9000
Fiber Cable
Note: This setup is basically also valid for 8800/8500 Dual camera
by basically using the correspondent Model into 9410 Local Printers
Note: The 9410/8500 configuration can not print some formats (eg 2:1 side by side, etc),
in this case the MIM200/8500 solve the problem ie print formats 2:1 side by side, etc
9410 Setup:
n on Device Setup, LOCAL PRINTERS:
n Printer=8500, Model=8500, Output=Fiber
n Baud=19200, Parity=None, Data=8, Stop=1, Command Set=Superset
n Pixel=12, Header/Line, Timeout=60, Transfer Rate=2 MHz
n Film Mismatch=Print Always, Interpolation Type=831
n Interp Num=11, Max.Density=300, Contrast=6, Border Density=0
n TFT/ULUT Emulation=On, Installed TFT/ULUT=Ver693c0.w87
n on Device Setup, SCP PRINTERS, Current Providers:
n Printer=8500, AE Title=9410, Port=1024, Max Associations=5
n on Device Setup, SCP PRINTERS, Registered Users:
n SCU AETitle=accordingly, SCU IPAddr=accordingly, SCP=8500
n Copies=1, Contrast Table=2, TFT/ULUT=Wrkstn2a.w87
n Max.Density=300, Border Density=0, Mag.Type=8, Smoothing=11
n Polarity=1, Orientation=1, Set Req.Image Size=No, Priority=Low
n Interceptor=Yes, N-Event-Print Job=No, N-Event Printer=No
n Trim=No, Attribute Warning=No
n Contrast Test Mode=No, Contrast Test Mode Density=0
DICOM Network
RS422
COPCIL Board 9-pole Plug
Copper Cable Control 9-pin
Kodak DirectView
-DR 5000
-DR 9000
Data 37-pin
Note: The 9410/8100 configuration can not print some formats (eg 2:1 side by side, etc),
in this case the MIM200/8100 solve the problem ie print formats 2:1 side by side, etc
9410 Setup:
on Device Setup, LOCAL PRINTERS:
n Printer=8100, Model=8100 4096 pxls/line, Output=Copper
n Baud=1200, Parity=Even, Data=8, Stop=1, Command Set=952
n Pixel=12, Header/Line, Timeout=60, Transfer Rate=1 MHz
n Film Mismatch=Print Always, Interpolation Type=831
n Interp Num=11, Max.Density=300, Contrast=6, Border Density=0
n TFT/ULUT Emulation=On, Installed TFT/ULUT=Ver693c0.w87
on Device Setup, SCP PRINTERS, Current Providers:
n Printer=8100, AE Title=9410, Port=1024, Max Associations=5
on Device Setup, SCP PRINTERS, Registered Users:
n SCU AETitle=accordingly, SCU IPAddr=accordingly
n SCP=8100, Copies=1, Contrast Table=2, TFT/ULUT=Wrkstn2a.w87
n Max.Density=300, Border Density=0, Mag.Type=8, Smoothing=11
n Polarity=1, Orientation=1, Set Req.Image Size=No, Priority=Low
n Interceptor=Yes, N-Event-Print Job=No, N-Event Printer=No
n Trim=No, Attribute Warning=No
n Contrast Test Mode=No, Contrast Test Mode Density=0
DICOM Network
Control 9 pin
Kodak DirectView COPCIL board
-DR 5000 Copper Cable
-DR 9000
Data 37 pin
Note: The 9410/8300 configuration can not print the Annotation Box (eg Patient Name),
in this case the MIM200/8300 solve the problem ie print the Annotation Box
Note: The 9410/8300 configuration can not print some formats (eg 2:1 side by side, etc),
in this case the MIM200/8300 solve the problem ie print formats 2:1 side by side, etc
9410 Setup:
n on Device Setup, LOCAL PRINTERS:
n Printer=8300, Model=8300 Copper, Output=Copper
n Command Set=952, Baud=1200, Data=8, Stop=1, Parity=Even
n Pixel=8, Header/Line, Timeout=60, Transfer Rate=1 MHz
n Film Mismatch=Print Always, Interpolation Type=831
n Interp Num=0, Max.Density=300, Contrast=6, Border Density=0
n TFT/ULUT Emulation=On, Installed TFT/ULUT= upmsv3k.w8u
n on Device Setup, SCP PRINTERS, Current Providers:
n Printer=8300, AE Title=9410, Port=1024, Max Associations=5
n on Device Setup, SCP PRINTERS, Registered Users:
n SCU AETitle=accordingly, SCU IPAddr=accordingly
n SCP=8300, Copies=1, Contrast Table=1, TFT/ULUT=wrkstn83a.w8u
n Max.Density=300, Border Density=0, Mag.Type=8, Smoothing=0
n Polarity=1, Orientation=1, Set Req.Image Size=No, Priority=Low
n Interceptor=Yes, N-Event-Print Job=No, N-Event Printer=No
n Trim=No, Attribute Warning=No
n Contrast Test Mode=No, Contrast Test Mode Density=0
8300 Setup:
n on Operator Menu set: D=16, C=6, Sharp/Smooth=0 i.e., Auto
n on Operator Menu set: Film Layout: 1 on 1=Portrait
n on Service Menu set: Ratio=1.00, Serial=1200,8,1,Even,Comma,3M, Memory=16
n on Service Menu set: Digital Interface: Parity=Even, Modality Group=1
DICOM Network
190 Setup:
n On 190 Control Panel press Menu, Setup:
n Printer Density=3.00, Curve Shape=0.0, Contrast=0, Contrast Pivot Density=1.2
n IPAddress=accordingly, Subnet Mask=accordingly, Gateway Address=accordingly
n Port=5040, Network Node Name=Kodak MLP190, Connection Type=RJ45
DICOM Network
Kodak DirectView
Kodak 2180 camera
-DR 5000
-DR 9000
Fiber Cable
MIM200 Setup:
n on Configure, Network:
n Computer Name=e.g., Kodak2180, IPAddr=accordingly
n Subnet Mask=accordingly, Gateway Addr=accordingly
n on Configure, Input, Network, Add:
n Protocol=DICOM 3.0, Log.Name=DICOM, Type/Com=Keypad/COM9
n on Configure, Destination, Add, Print, Direct, Qualified, KELP 2180, Set:
n General: Log.Name=KELP2180, Database Name=KELP 2180
n General: Model=KELP 2180, Memory=24, Node ID=6 or accordingly
n Media Info: Media=35x43cm, 4136x5160, 5030, (Blue)
n Media Info:Media=35x35cm,4136x4136,4006, (Blue)
n Media Info: Media=11x14in, 3240x4136, 4006, (Blue)
n Media Info: Media=8x10in, 2290x2840, 2710, (Blue)
n Supported Item: Collation=On, Text=On, Tonescaling=On, Rotation=On
n Interpolation: NoMag=On, Bil=On, Repl=On,Cubic=On, Cubic 2=On
n Format Types: Custom=On, Slide=On, Row Symmetric=On
n Format Types: 1, 2, 4, 6, 8, 9, 12, 15, 16, 20, 24, 30, 35=On
n Formatting: Aspect Ratio Mix on Page=On, Image Size Mix in Std Fmt=On
n Formatting: DICOM Annotation Box=On, Req.Size Scale=On
n Formatting: Req.Size Mix in Row=On, Trim=On
n Formatting: Aspect Ratio Mix in Row=On, Image Size Mix in Row=On
n Formatting: Req.Image Size=On, Req.Size Mix on Page=On
n Formatting: True Landscape=On
n Formatting: Max Img per Band=20, Max Band per Page=20, Max Img Col=0
n Formatting: Max Img Row=0, Min Horiz Sep=2, Min Vert Sep=2
n Formatting: Trim Width Enabled=2, Trim Width Disabled=2
n Formatting: Pixel Pitch=12.6582
n Image Processing: Grayscale=On, Minify=On, Max Image Dmax=3.2
n M952 Usage: Min H/V Mag=0, Max H/V Mag=0, Min Dmax 952=1.7
2180 Setup:
n Optical Interface board will automatic configure into 2180, no setup needed
DICOM Network
Kodak DirectView
Kodak 1120 camera
-DR 5000
-DR 9000
Fiber Cable
MIM200 Setup:
n on Configure, Network:
n Computer Name=e.g., Kodak1120, IPAddr=accordingly
n Subnet Mask=accordingly, Gateway Addr=accordingly
n on Configure, Input, Network, Add:
n Protocol=DICOM 3.0, Log.Name=DICOM, Type/Com=Keypad/COM9
n on Configure, Destination, Add, Print, Direct, Qualified, KELP 1120, Set:
n General: Log.Name=KELP1120, Database Name=KELP 1120
n General: Model=KELP 1120, Memory=20, Node ID=6 or accordingly
n Media Info: Media=35x43cm, 4096x5132, 5034, (Blue)
n Media Info: Media=35x35cm, 4096x4108, 4010, (Blue)
n Media Info: Media=11x14in, 4096x3232, 3134, (Blue)
n Media Info: Media=8x10in, 2304x2900, 2802, (Blue)
n Supported Item: Collation=On, Text=On, Tonescaling=On, Rotation=On
n Interpolation: NoMag=On, Repl=On,Cubic Spline=On
n Format Types: Custom=On, Slide=On, Row Symmetric=On
n Format Types: 1, 2, 4, 6, 8, 9, 12, 15, 16, 20, 24, 30, 35=On
n Formatting: Aspect Ratio Mix on Page=On, Image Size Mix in Std Fmt=On
n Formatting: DICOM Annotation Box=On, Req.Size Scale=On
n Formatting: Req.Size Mix in Row=On
n Formatting: Aspect Ratio Mix in Row=On, Image Size Mix in Row=On
n Formatting: Req.Image Size=On, Req.Size Mix on Page=On
n Formatting: True Landscape=On
n Formatting: Max Img per Band=20, Max Band per Page=20, Max Img Col=0
n Formatting: Max Img Row=0, Min Horiz Sep=3, Min Vert Sep=0
n Formatting: Trim Width Enabled=0, Trim Width Disabled=0
n Formatting: Pixel Pitch=12.5
n Image Processing: Grayscale=On, Minify=On, Max Image Dmax=2.8
n M952 Usage: Min H/V Mag=0, Max H/V Mag=0, Min Dmax 952=1.7
1120 Setup:
n Optical Interface board will automatic configure into 1120, no setup needed
DICOM Network
Kodak DirectView
-DR 5000 Kodak 160 camera
Crossed
-DR 9000
Network Cable
MIM200 Setup:
n on Configure, Network:
n Computer Name=e.g., Kodak160, IPAddr=accordingly
n Subnet Mask=accordingly, Gateway Addr=accordingly
n on Configure, Input, Network, Add:
n Protocol=DICOM 3.0, Log.Name=DICOM, Type/Com=Keypad/COM9
n on Configure, Destination, Add, Print, Direct, Qualified, KELI 160, Set:
n General: Log.Name=KELI 160, IPAddr=100.100.100.30,
n General: Database Name=KELI 160, Model=KELI 160
n Media Info: Media=35x43cm, 4361x5348, 5228, Any (Blue,Clear)
n Supported Item: Collation=On, Text=On, Tonescaling on Image=On
n Supported Item: Pivot Density=On, Rotation=On
n Interpolation: NoMag=On, Bil=On, Repl=On,Cubic=On, Cubic 2=On
n Format Types: Custom=On, Slide=On, Row Symmetric=On
n Format Types: 1, 2, 4, 6, 8, 9, 12, 15, 16, 20, 24, 30, 35=On
n Formatting: Aspect Ratio Mix on Page=On, Image Size Mix in Std Fmt=On
n Formatting: DICOM Annotation Box=On, Req.Size Scale=On
n Formatting: Req.Size Mix in Row=On, Trim=On
n Formatting: Aspect Ratio Mix in Row=On, Image Size Mix in Row=On
n Formatting: Req.Image Size=On, Req.Size Mix on Page=On
n Formatting: True Landscape=On
n Formatting: Max Img per Band=20, Max Band per Page=20, Max Img Col=0
n Formatting: Max Img Row=0, Min Horiz Sep=2, Min Vert Sep=2
n Formatting: Trim Width Enabled=2, Trim Width Disabled=0
n Formatting: Pixel Pitch=12.8
n Image Processing: Grayscale=On, Minify=On, Max Image Dmax=3.2
n M952 Usage: Min H/V Mag=0, Max H/V Mag=0, Min Dmax 952=1.7
DICOM Network
iew
00 DryV
3M 87
Kodak DirectView
Fiber Cable
-DR 5000
-DR 9000
Fiber Cable
MIM200 Setup:
n on Configure, Network:
n Node Name=MIM, IPAddr=accordingly
n Subnet Mask=accordingly, Gateway Addr=accordingly
n on Configure, Input, Network, Add:
n Protocol=DICOM 3.0, Log.Name=DICOM, Type/Com=Keypad/COM9
n on Configure, Destination, Add, Print, Direct, Qualified, 8700, Set:
n General: Log.Name=8700
n General: Database Name=8700, Model=8700, Memory=32
n Media Info: Media=35x43cm, 4096x5223, 5133, Blue
n Output Params: Cmd=SuperSet,Baud=19200,Data=8,Stop=1,Parity=None
n Output Params: Pixel=12, Header/Line, Transfer=2000 KHz, Acq=60
n Supported Item: Collation=On, Text=On, Tonescaling=On, Rotation=On
n Interpolation: NoMag=On, Bilin=On, Repl=On,Cubic Spline=On
n Format Types: Custom=On, Slide=On, Row Symmetric=On
n Format Types: 1, 2, 4, 6, 8, 9, 12, 15, 16, 20, 24, 30, 35=On
n Formatting: Aspect Ratio Mix on Page=On, Image Size Mix in Std Fmt=On
n Formatting: DICOM Annotation Box=On, Req.Size Scale=On
n Formatting: Req.Size Mix in Row=On, Trim=On
n Formatting: Aspect Ratio Mix in Row=On, Image Size Mix in Row=On
n Formatting: Req.Image Size=On, Req.Size Mix on Page=On
n Formatting: True Landscape=On
n Formatting: Max Img per Band=20, Max Band per Page=20, Max Img Col=0
n Formatting: Max Img Row=0, Min Horiz Sep=2, Min Vert Sep=2
n Formatting: Trim Width Enabled=2, Trim Width Disabled=0
n Formatting: Pixel Pitch=12.8205
n Image Processing: Grayscale=On, Minify=On, Max Image Dmax=3.1
n M952 Usage: Min H/V Mag=1, Max H/V Mag=64, Min Dmax 952=1.7
DICOM Network
iew
00 DryV
3M 87
Kodak DirectView
Fiber Cable
-DR 5000
-DR 9000
Fiber Cable
MIM200 Setup:
n on Configure, Network:
n Node Name=MIM, IPAddr=accordingly
n Subnet Mask=accordingly, Gateway Addr=accordingly
n on Configure, Input, Network, Add:
n Protocol=DICOM 3.0, Log.Name=DICOM, Type/Com=Keypad/COM9
n on Configure, Destination, Add, Print, Direct, Qualified, 8500, Set:
n General: Log.Name=8500
n General: Database Name=8500, Model=8500, Memory=32
n Media Info: Media=11x14in, 3388x4283, 4193, Blue
n Output Params: Cmd=SuperSet,Baud=19200,Data=8,Stop=1,Parity=None
n Output Params: Pixel=12, Header/Line, Transfer=2000 KHz, Acq=60
n Supported Item: Collation=On, Text=On, Tonescaling=On, Rotation=On
n Interpolation: NoMag=On, Bilin=On, Repl=On,Cubic Spline=On
n Format Types: Custom=On, Slide=On, Row Symmetric=On
n Format Types: 1, 2, 4, 6, 8, 9, 12, 15, 16, 20, 24, 30, 35=On
n Formatting: Aspect Ratio Mix on Page=On, Image Size Mix in Std Fmt=On
n Formatting: DICOM Annotation Box=On, Req.Size Scale=On
n Formatting: Req.Size Mix in Row=On, Trim=On
n Formatting: Aspect Ratio Mix in Row=On, Image Size Mix in Row=On
n Formatting: Req.Image Size=On, Req.Size Mix on Page=On
n Formatting: True Landscape=On
n Formatting: Max Img per Band=20, Max Band per Page=20, Max Img Col=0
n Formatting: Max Img Row=0, Min Horiz Sep=2, Min Vert Sep=2
n Formatting: Trim Width Enabled=2, Trim Width Disabled=0
n Formatting: Pixel Pitch=12.8205
n Image Processing: Grayscale=On, Minify=On, Max Image Dmax=3.1
n M952 Usage: Min H/V Mag=1, Max H/V Mag=64, Min Dmax 952=1.7
DICOM Network
RS422
COPCIL Board 9-pole Plug
Copper Cable Control 9-pin
Kodak DirectView
-DR 5000
-DR 9000
Data 37-pin
MIM200 Setup:
n on Configure, Network:
n Node Name=MIM, IPAddr=accordingly
n Subnet Mask=accordingly, Gateway Addr=accordingly
n on Configure, Input, Network, Add:
n Protocol=DICOM 3.0, Log.Name=DICOM, Type/Com=Keypad/COM9
n on Configure, Destination, Add, Print, Direct, Qualified, 8100, Set:
n General: Log.Name=8100
n General: Database Name=8100, Model=8100, Memory=32
n Media Info: Media=35x43cm, 4096x5223, 5133, Blue
n Output Params: Cmd Set=952, Baud=1200, Data=8, Stop=1, Parity=Even
n Output Params: Pixel=12, Header/Line, Transfer=1000 KHz, Acquire=60
n Supported Item: Collation=On, Text=On, Tonescaling=On, Rotation=On
n Interpolation: NoMag=On, Bilin=On, Repl=On,Cubic Spline=On
n Format Types: Custom=On, Slide=On, Row Symmetric=On
n Format Types: 1, 2, 4, 6, 8, 9, 12, 15, 16, 20, 24, 30, 35=On
n Formatting: Aspect Ratio Mix on Page=On, Image Size Mix in Std Fmt=On
n Formatting: DICOM Annotation Box=On, Req.Size Scale=On
n Formatting: Req.Size Mix in Row=On, Trim=On
n Formatting: Aspect Ratio Mix in Row=On, Image Size Mix in Row=On
n Formatting: Req.Image Size=On, Req.Size Mix on Page=On
n Formatting: True Landscape=On
n Formatting: Max Img per Band=20, Max Band per Page=20, Max Img Col=0
n Formatting: Max Img Row=0, Min Horiz Sep=2, Min Vert Sep=2
n Formatting: Trim Width Enabled=2, Trim Width Disabled=0
n Formatting: Pixel Pitch=12.8205
n Image Processing: Grayscale=On, Minify=On, Max Image Dmax=3.1
n M952 Usage: Min H/V Mag=1, Max H/V Mag=64, Min Dmax 952=1.7
DICOM Network
Control 9 pin
Kodak DirectView COPCIL board
-DR 5000 Copper Cable
-DR 9000
Data 37 pin
MIM200 Setup:
n on Configure, Network:
n Node Name=MIM, IPAddr=accordingly
n Subnet Mask=accordingly, Gateway Addr=accordingly
n on Configure, Input, Network, Add:
n Protocol=DICOM 3.0, Log.Name=DICOM, Type/Com=Keypad/COM9
n on Configure, Destination, Add, Print, Direct, Qualified, 8300, Set:
n General: Log.Name=8300
n General: Database Name=8300, Model=8300, Memory=32
n Media Info: Media=8x10in, 2256x2676, 2596, Blue
n Output Params: Cmd Set=952, Baud=1200, Data=8, Stop=1, Parity=Even
n Output Params: Pixel=8, Header/Line, Transfer=2000 KHz, Acquire=60
n Supported Item: Collation=On, Text=On, Tonescaling=On, Rotation=On
n Interpolation: NoMag=On, Bilin=On, Repl=On,Cubic Spline=On
n Format Types: Custom=On, Slide=On, Row Symmetric=On, SuperSlide=On
n Format Types: 1, 2, 4, 6, 8, 9, 12, 15, 16, 20, 24, 30, 35=On
n Formatting: Aspect Ratio Mix on Page=On, Image Size Mix in Std Fmt=On
n Formatting: DICOM Annotation Box=On, Req.Size Scale=On
n Formatting: Req.Size Mix in Row=On, Trim=On
n Formatting: Aspect Ratio Mix in Row=On, Image Size Mix in Row=On
n Formatting: Req.Image Size=On, Req.Size Mix on Page=On
n Formatting: True Landscape=On
n Formatting: Max Img per Band=20, Max Band per Page=20, Max Img Col=0
n Formatting: Max Img Row=0, Min Horiz Sep=2, Min Vert Sep=2
n Formatting: Trim Width Enabled=2, Trim Width Disabled=0
n Formatting: Pixel Pitch=11.811
n Image Processing: Grayscale=On, Minify=On, Max Image Dmax=3
n M952 Usage: Min H/V Mag=1, Max H/V Mag=16, Min Dmax 952=1.5
8300 Setup:
n on Operator Menu set: D=16, C=6, Sharp/Smooth=0 i.e., Auto
n on Operator Menu set: Film Layout: 1 on 1=Portrait
n on Service Menu set: Ratio=1.00, Serial=1200,8,1,Even,Comma,3M, Memory=16
n on Service Menu set: Digital Interface: Parity=Even, Modality Group=1
DICOM Network
Kodak DirectView
-DR 5000
-DR 9000 Crossed
Network Cable
MIM200 Setup:
n on Configure, Network:
n Node Name=MIM, IPAddr=accordingly
n Subnet Mask=accordingly, Gateway Addr=accordingly
n on Configure, Input, Network, Add:
n Protocol=DICOM 3.0, Log.Name=DICOM, Type/Com=Keypad/COM9
n on Configure, Destination, Add, Print, Direct, Qualified, 8200, Set:
n General: Log.Name=8200, IPAddr=100.100.100.40,
n General: Database Name=8200, Model=8200, Memory=32
n Media Info: Media=35x43cm, 4361x5223, 5133, Any (Blue,Clear)
n Media Info: Media=35x35cm, 4361x4247, 4157, Any (Blue,Clear)
n Media Info: Media=11x14in, 3272x4361, 4271, Any (Blue,Clear)
n Supported Item: Collation=On, Common Text=On, Tonescaling=On
n Supported Item: Remote Image Deletion=On, Rotation=On
n Interpolation: No Magnification=On, Bilin=On, Repl=On
n Interpolation: Cubic Spline=On, Cubic Convolution 2=On
n Format Types: Custom=On, Row Symmetric=On
n Format Types: 1, 2, 4, 6, 8, 9, 12, 15, 16, 20, 24, 30, 35=On
n Formatting: Aspect Ratio Mix on Page=On, Image Size Mix in Std Fmt=On
n Formatting: DICOM Annotation Box=On, Req.Size Scale=On
n Formatting: Req.Size Mix in Row=On, Trim=On
n Formatting: Aspect Ratio Mix in Row=On, Image Size Mix in Row=On
n Formatting: Req.Image Size=On, Req.Size Mix on Page=On
n Formatting: True Landscape=On
n Formatting: Max Img per Band=20, Max Band per Page=20, Max Img Col=0
n Formatting: Max Img Row=0, Min Horiz Sep=2, Min Vert Sep=2
n Formatting: Trim Width Enabled=2, Trim Width Disabled=0
n Formatting: Pixel Pitch=12.8205
DICOM Network
Kodak DirectView
-DR 5000
-DR 9000
8900 Setup:
n on Configuration, System, Network:
n Host Name=DV8900, IPAddr=accordingly
n Subnet Mask=accordingly, Gateway Addr=accordingly
n on Configuration, DICOM SCP, Communications:
n Port=5040, Association Limit=12, Source Name=DICOM
n on Configuration, Destination:
n General: Log.Name=8900
n Media Types: Media=35x43cm, 9100x11037, 10781, Any
n Media Types: Media=35x35cm,9100x9087, 8831, Any
n Media Types: Media=11x14in, 7137x9100, 8844, Any
n Media Types: Media=10x12in, 6490x7767, 7511, Any
n Media Types: Media=8x10in, 5167x6490, 6234, Any
n Formatting: Aspect Ratio Mix Page=On, Aspect Ratio Mix Row=On
n Formatting: Image Size Mix in Std Fmt=On, Image Size Mix Row=On
n Formatting: DICOM Annotation Box=On, Req.Image Size=On
n Formatting: Req.Size Scale=On, Req.Size Mix Page=On
n Formatting: Req.Size Mix Row=On, Trim=On,
n Formatting: True Landscape=On, Rotation=On
n Formatting: Minify/Crop=On, Tonescaling on Image Basis=On
n Formatting: Max Img Band=7, Max Band Page=7, Max Img Cols=0
n Formatting: Max Img Rows=0, Pixel Pitch=25.5910, Min Horiz Sep=4
n Formatting: Min Vert Sep=4, Trim Width Enabled=4
n Formatting: Trim Width Disabled=0, Maximum DMAX=3.30
n on Configuration, DICOM SCP, SCP Services, select specific modality, Modify:
n Negotiate Presentation LUT=No, Negotiate Color Print=No
n TFT= Wrkstn2a.w87 (Always=N), Contrast=2 (Always=N)
n Smoothing Type=11 (Always=N), Image Polarity=Normal (Always=N)
n Image Dmin=0.00 (Always=N), Image Dmax=3.00 (Always=N)
n NeventReports=No (Always=Y), Warnings=Yes
n Print Priority=Normal (Always=N), Border=3.99 (Always=N)
n 2mm Border=Yes, Film Clip Border=No, Film Base=Blue Film (Always=N)
n Film Size=14INx17IN (Always=N), Sorter Bin=Bin1 (Always=N)
n Print Date=No, Print Time=No, Page Nbr=No, Hosp.Name=No
n Modality ID=No, Annotation Override=No, Density Patch=No
n Image Resizing=Minify/Scale (Always=N),
n Text Box Location=None, Source ID=dr
Kodak DirectView
-DR 5000
-DR 9000
8150 Setup:
n on Configuration, System, Network:
n Host Name=DV8150DRE, IPAddr=accordingly
n Subnet Mask=accordingly, Gateway Addr=accordingly
n on Configuration, DICOM SCP, Communications:
n Port=5040, Association Limit=12, Source Name=DICOM
n on Configuration, Destination:
n AE Title: Log.Name=DV8150
n Media Types: Media=35x43cm, 4438x5390, 5262, Any
n Media Types: Media=35x35cm, 4438x4414,4286, Any
n Media Types: Media=11x14in, 3440x4438, 4310, Any
n Formatting: Aspect Ratio Mix Page=On, Aspect Ratio Mix Row=On
n Formatting: Image Size Mix in Std Fmt=On, Image Size Mix Row=On
n Formatting: DICOM Annotation Box=On, Req.Image Size=On
n Formatting: Req.Size Scale=On, Req.Size Mix Page=On
n Formatting: Req.Size Mix Row=On, Trim=On,
n Formatting: True Landscape=On, Rotation=On
n Formatting: Minify/Crop=On, Tonescaling on Image Basis=On
n Formatting: Max Img Band=7, Max Band Page=7, Max Img Cols=0
n Formatting: Max Img Rows=0, Pixel Pitch=12.8000, Min Horiz Sep=2
n Formatting: Min Vert Sep=2, Trim Width Enabled=2
n Formatting: Trim Width Disabled=0, Maximum DMAX=3.10
n on Configuration, DICOM SCP, SCP Services, select specific modality, Modify:
n Negotiate Presentation LUT=No, Negotiate Color Print=No,
n TFT Set Name=Wrkstn2a.w87 (Always=Y)
n Contrast=1 (Always=N), Smoothing Type=11 (Always=N)
n Dmin=0.00 (Always=N), Dmax=3.00 (Always=N)
n Image Polarity=Normal (Always=N)
n NeventReports=No (Always=Y), Warnings=Yes
n Print Priority=Normal (Always=N), Border=3.99 (Always=N)
n 2mm Border=Yes, Film Clip Border=No,
n Film Base=Blue Film (Always=N), Film Size=14INx17IN (Always=N)
n Print Date=No, Print Time=No, Page Nbr=No, Hosp.Name=No,
n Modality ID=No, Annotation Override=No, Density Patch=No
n Image Resizing=Minify/Scale (Always=N),
n Text Box Location=None, Source ID=dr
DICOM Network
Kodak DirectView
-DR 5000
-DR 9000
CMI-1000 Setup:
at Local Panel, under Media, set A4 or Letter ie what inside Paper Tray
(CMI-1000 sw considers only this field and uses it as A4 or Letter (Always=Y):
at Local Panel, under Menu, Imager Setup:
n Network Setup:
n IPAddr=accordingly, Subnet Mask=accordingly, Gateway=accordingly
n under More Settings: DICOM Port=5040
n Edit Host Name/AE Title=CMI1000
n Modality (SCU) Config (or after modality recognition):
n Select Modality=accordingly, Modality Config.Assistant=Yes, Reset Config=No
n Note: Color IQ settings used when images sent with Color DICOM SOP
n under Image Quality, Color Image Quality: (no need to adjust, leave defaults)
n Match Monitor Colors=default ie sRGB Color Space Profile.icm
n Adjust Color Tones=default ie Default_Contrast_100.icm
n Note: Grayscale IQ settings used when images sent with Grayscale DICOM SOP:
n under Image Quality, Grayscale Image Quality:
n Contrast=7 (Always=Y)
n TFT Set (From list)=Wrkstn2a.w87 (Always=Y)
n Wet Contrast=0 (Always=N), Curve Shape=429 (Always=N)
n under More Quality Settings:
n Tonescaling=Presentation LUT (Always=N),
n Image Dmax=220 (Always=N), Image Dmin=10 (Always=N)
n Smoothing=11 (Always=Y), Polarity=Positive (Always=N)
n Interpolation=CUBIC (Always=N), Trim=No (Always=N)
n Page Orientation=PORTRAIT (Always=N), Negotiate PLUT=No
n under Modality Defaults:
n Media Size=8.5x11 (Always=N), don’t care, this field plays no role
n Image Resizing=Minify (Always=N),
n Priority=Normal (Always=N), NeventReports=No (Always=Y),
n Warnings=Yes, Color=Yes
n (set Color=No when only b/w images are printed and set it to be sure
n to apply to the b/w images the Greyscale Image Quality settings)
n Page Annotation:
n Hosp.Name=No, Modality ID=No, Page Nbr=No, Date=No, Time= No
n Save Changes and Exit
1
setup valid also for Kodak PACS LINK 25 PRINT SERVER.
DICOM Network
iew
00 DryV
3M 87
Kodak DirectView
Fiber Cable
-DR 5100
-DR 7100
-DR 5000 Console Upgrade Fiber Cable
-DR 9000 Console Upgrade
Note: This setup is basically also valid for 8800/8700 Dual camera
by basically using the correspondent Model into 9410 Local Printers
9410 Setup:
n on Device Setup, LOCAL PRINTERS:
n Printer=8700, Model=8700, Output=Fiber
n Baud=19200, Parity=None, Data=8, Stop=1, Command Set=Superset
n Pixel=12, Header/Line, Timeout=60, Transfer Rate=2 MHz
n Film Mismatch=Print Always, Interpolation Type=831
n Interp Num=11 Max.Density=300, Contrast=6, Border Density=0
n TFT/ULUT Emulation=On, Installed TFT/ULUT=Ver693c0.w87
n on Device Setup, SCP PRINTERS, Current Providers:
n Printer=8700, AE Title= NER_9410, Port= 1024, Max Associations= 5
n on Device Setup, SCP PRINTERS, Registered Users:
n SCU AETitle=accordingly, SCU IPAddr=accordingly, SCP=8700
n Copies=1, Contrast Table=2, TFT/ULUT=Wrkstn2a.w87
n Max.Density=300, Border Density=0, Mag.Type=8, Smoothing=11
n Polarity=1, Orientation=1, Set Req.Image Size=No, Priority=Low
n Interceptor=Yes, N-Event-Print Job=No, N-Event Printer=No
n Trim=No, Attribute Warning=No
n Contrast Test Mode=No, Contrast Test Mode Density=0
DICOM Network
iew
00 DryV
3M 87
Kodak DirectView
Fiber Cable
-DR 5100
-DR 7100
-DR 5000 Console Upgrade Fiber Cable
-DR 9000 Console Upgrade
Note: This setup is basically also valid for 8800/8500 Dual camera
by basically using the correspondent Model into 9410 Local Printers
9410 Setup:
DICOM Network
RS422
COPCIL Board 9-pole Plug
Copper Cable Control 9-pin
Kodak DirectView
-DR 5100
-DR 7100
-DR 5000 Console Upgrade
-DR 9000 Console Upgrade Data 37-pin
9410 Setup:
on Device Setup, LOCAL PRINTERS:
n Printer=8100, Model=8100 4096 pxls/line, Output=Copper
n Baud=1200, Parity=Even, Data=8, Stop=1, Command Set=952
DICOM Network
Control 9 pin
Kodak DirectView COPCIL board
-DR 5100 Copper Cable
-DR 7100
-DR 5000 Console Upgrade Data 37 pin
-DR 9000 Console Upgrade
Note: The 9410/8300 configuration can not print the External Text Annotation Box,
in this case MIM200/8300 solve the problem ie print External Text Annotation Box
9410 Setup:
8300 Setup:
n on Operator Menu set: D=16, C=6, Sharp/Smooth=0 ie Auto
n on Operator Menu set: Film Layout: 1 on 1=Portrait
n on Service Menu set: Ratio=1.00, Serial=1200,8,1,Even,Comma,3M, Memory=16
n on Service Menu set: Digital Interface: Parity=Even, Modality Group=1
DICOM Network
190 Setup:
n On 190 Control Panel press Menu, Setup:
n Printer Density=3.00, Curve Shape=0.0, Contrast=0, Contrast Pivot Density=1.2
n IPAddress=accordingly, Subnet Mask=accordingly, Gateway Address=accordingly
n Port=5040, Network Node Name=Kodak MLP190, Connection Type=RJ45
DICOM Network
Kodak DirectView
Kodak 2180 camera
-DR 5100
-DR 7100
-DR 5000 Console Upgrade Fiber Cable
-DR 9000 Console Upgrade
MIM200 Setup:
n on Configure, Network:
n Computer Name=eg Kodak2180, IPAddr=accordingly
n Subnet Mask=accordingly, Gateway Addr=accordingly
n on Configure, Input, Network, Add:
n Protocol=DICOM 3.0, Log.Name=DICOM, Type/Com=Keypad/COM9
n on Configure, Destination, Add, Print, Direct, Qualified, KELP 2180, Set:
n General: Log.Name=KELP2180, Database Name=KELP 2180
n General: Model=KELP 2180, Memory=24, Node ID=6 or accordingly
n Media Info: Media=35x43cm, 4136x5160, 5030, (Blue)
n Media Info:Media=35x35cm,4136x4136,4006, (Blue)
n Media Info: Media=11x14in, 3240x4136, 4006, (Blue)
n Media Info: Media=8x10in, 2290x2840, 2710, (Blue)
n Supported Item: Collation=On, Text=On, Tonescaling=On, Rotation=On
n Interpolation: NoMag=On, Bil=On, Repl=On,Cubic=On, Cubic 2=On
n Format Types: Custom=On, Slide=On, Row Symmetric=On
n Format Types: 1, 2, 4, 6, 8, 9, 12, 15, 16, 20, 24, 30, 35=On
n Formatting: Aspect Ratio Mix Page=On, Image Size Mix in Std Fmt=On
n Formatting: DICOM Annotation Box=On, Req.Size Scale=On
n Formatting: Req.Size Mix in Row=On, Trim=On
n Formatting: Aspect Ratio Mix in Row=On, Image Size Mix in Row=On
n Formatting: Req.Image Size=On, Req.Size Mix on Page=On
n Formatting: True Landscape=On
n Formatting: Max Img Band=20, Max Band per Page=20, Max Img Col=0
n Formatting: Max Img Row=0, Min Horiz Sep=2, Min Vert Sep=2
n Formatting: Trim Width Enabled=2, Trim Width Disabled=2
n Formatting: Pixel Pitch=12.6582
n Image Processing: Grayscale=On, Minify=On, Max Image Dmax=3.2
n M952 Usage: Min H/V Mag=0, Max H/V Mag=0, Min Dmax 952=1.7
n on Configure, SCP Services, select the specific modality, Modify:
n PLUT=N, ToneScaling=Curve Shape (Always=Y)
n Curve Shape= 0 (Always=N), Contrast (wet)=0 (Always=N)
n Image Dmin=0.00 (Always=N), Image Dmax=3.00 (Always=N)
n NeventReports=Off (Always=Y), Warning Status=On
n Print Date=Off, Print Time=Off, Page Number=Off, Hosp.Name=Off
n Modality ID=Off, Annotation Override=Off (Always=N)
n Minify/Scale=On, Crop=Off, Text Box Relocation=None
n Print Priority=Normal (Always=N), Border=Black (Always=N)
n Interpolation=Cubic, Border Dmax=3.99
n Film Size=14INx17IN (Always=N), Film Output Dest=Bin 9 (Always=N)
n Negotiate Color Print=Off
2180 Setup:
n Optical Interface board will automatic configure into 2180, no setup needed
DICOM Network
Kodak DirectView
-DR 5100 Kodak 160 camera
Crossed
-DR 7100
Network Cable
-DR 5000 Console Upgrade
-DR 9000 Console Upgrade
n M952 Usage: Min H/V Mag=0, Max H/V Mag=0, Min Dmax 952=1.7
MIM200 Setup:
n on Configure, Network:
n Computer Name=eg Kodak160, IPAddr=accordingly
n Subnet Mask=accordingly, Gateway Addr=accordingly
n on Configure, Input, Network, Add:
n Protocol=DICOM 3.0, Log.Name=DICOM, Type/Com=Keypad/COM9
n on Configure, Destination, Add, Print, Direct, Qualified, KELI 160, Set:
n General: Log.Name=160, IPAddr=100.100.100.30,
n General: Database Name=KELI 160, Model=KELI 160
n Media Info: Media=35x43cm, 4361x5348, 5228, Any (Blue,Clear)
n Supported Item: Collation=On, Text=On, Tonescaling on Image=On
n Supported Item: Pivot Density=On, Rotation=On
n Interpolation: NoMag=On, Bil=On, Repl=On,Cubic=On, Cubic 2=On
n Format Types: Custom=On, Slide=On, Row Symmetric=On
n Format Types: 1, 2, 4, 6, 8, 9, 12, 15, 16, 20, 24, 30, 35=On
n Formatting: Aspect Ratio Mix Page=On, Image Size Mix in Std Fmt=On
n Formatting: DICOM Annotation Box=On, Req.Size Scale=On
n Formatting: Req.Size Mix in Row=On, Trim=On
n Formatting: Aspect Ratio Mix in Row=On, Image Size Mix in Row=On
n Formatting: Req.Image Size=On, Req.Size Mix on Page=On
n Formatting: True Landscape=On
n Formatting: Max Img Band=20, Max Band per Page=20, Max Img Col=0
n Formatting: Max Img Row=0, Min Horiz Sep=2, Min Vert Sep=2
n Formatting: Trim Width Enabled=2, Trim Width Disabled=0
n Formatting: Pixel Pitch=12.8
n Image Processing: Grayscale=On, Minify=On, Max Image Dmax=3.2
n M952 Usage: Min H/V Mag=0, Max H/V Mag=0, Min Dmax 952=1.7
n on Configure, SCP Services, select the specific modality, Modify:
n PLUT=N, ToneScaling=Curve Shape (Always=Y)
n Curve Shape= 0 (Always=N), Contrast (wet)=0 (Always=N)
n Image Dmin=0.00 (Always=N), Image Dmax=3.00 (Always=N)
n Interpolation=Cubic, Image Polarity=Normal (Always=N)
n NeventReports=Off (Always=Y), Warning Status=On
n Print Date=Off, Print Time=Off, Page Number=Off, Hosp.Name=Off
n Modality ID=Off, Annotation Override=Off (Always=N)
n Minify/Scale=On, Crop=Off, Text Box Relocation=None (Always=N)
n Print Priority=Normal (Always=N), Border=3.99 (Always=N)
n Film Base=Blue Film (Always=N), Film Size=14INx17IN (Always=N)
n Negotiate Color Print=Off
DICOM Network
iew
00 DryV
3M 87
Kodak DirectView
Fiber Cable
-DR 5100
-DR 7100
-DR 5000 Console Upgrade Fiber Cable
-DR 9000 Console Upgrade
MIM200 Setup:
n on Configure, Network:
n Node Name=MIM, IPAddr=accordingly
n Subnet Mask=accordingly, Gateway Addr=accordingly
n on Configure, Input, Network, Add:
n Protocol=DICOM 3.0, Log.Name=DICOM, Type/Com=Keypad/COM9
n on Configure, Destination, Add, Print, Direct, Qualified, 8700, Set:
n General: Log.Name=8700
n General: Database Name=8700, Model=8700, Memory=32
n Media Info: Media=35x43cm, 4096x5223, 5133, Blue
n Output Params: Cmd=SuperSet,Baud=19200,Data=8,Stop=1,Parity=None
n Output Params: Pixel=12, Header/Line, Transfer=2000 KHz, Acq=60
n Supported Item: Collation=On, Text=On, Tonescaling=On, Rotation=On
n Interpolation: NoMag=On, Bilin=On, Repl=On,Cubic Spline=On
n Format Types: Custom=On, Slide=On, Row Symmetric=On
n Format Types: 1, 2, 4, 6, 8, 9, 12, 15, 16, 20, 24, 30, 35=On
n Formatting: Aspect Ratio Mix Page=On, Image Size Mix in Std Fmt=On
n Formatting: DICOM Annotation Box=On, Req.Size Scale=On
n Formatting: Req.Size Mix in Row=On, Trim=On
n Formatting: Aspect Ratio Mix in Row=On, Image Size Mix in Row=On
n Formatting: Req.Image Size=On, Req.Size Mix on Page=On
n Formatting: True Landscape=On
n Formatting: Max Img Band=20, Max Band per Page=20, Max Img Col=0
n Formatting: Max Img Row=0, Min Horiz Sep=2, Min Vert Sep=2
n Formatting: Trim Width Enabled=2, Trim Width Disabled=0
n Formatting: Pixel Pitch=12.8205
n Image Processing: Grayscale=On, Minify=On, Max Image Dmax=3.1
n M952 Usage: Min H/V Mag=1, Max H/V Mag=64, Min Dmax 952=1.7
n on Configure, SCP Services, select the specific modality, Modify:
n PLUT=N, ToneScaling=PerceptionLUT (Always=Y)
n TFT/ULUT= Wrkstn2a.w87 (Always=Y), Contrast (dry)=2 (Always=N)
n Image Dmin=0.00 (Always=N), Image Dmax=3.00 (Always=N)
n Smoothing Type=11 (Always=N), Image Polarity=Normal (Always=N)
n NeventReports=Off (Always=Y), Warning Status=On
n Print Date=Off, Print Time=Off, Page Number=Off, Hosp.Name=Off
n Modality ID=Off, Annotation Override=Off (Always=N)
n Minify/Scale=On, Crop=Off, Text Box Relocation=None
n Print Priority=Normal (Always=N), Border=3.99 (Always=N)
n Film Base=Blue Film (Always=N), Film Size=14INx17IN (Always=N)
n Negotiate Color Print=Off
DICOM Network
iew
00 DryV
3M 87
Kodak DirectView
Fiber Cable
-DR 5100
-DR 7100
-DR 5000 Console Upgrade Fiber Cable
-DR 9000 Console Upgrade
MIM200 Setup:
n on Configure, Network:
n Node Name=MIM, IPAddr=accordingly
n Subnet Mask=accordingly, Gateway Addr=accordingly
n on Configure, Input, Network, Add:
n Protocol=DICOM 3.0, Log.Name=DICOM, Type/Com=Keypad/COM9
n on Configure, Destination, Add, Print, Direct, Qualified, 8500, Set:
n General: Log.Name=8500
n General: Database Name=8500, Model=8500, Memory=32
n Media Info: Media=11x14in, 3388x4283, 4193, Blue
n Output Params: Cmd=SuperSet,Baud=19200,Data=8,Stop=1,Parity=None
n Output Params: Pixel=12, Header/Line, Transfer=2000 KHz, Acq=60
n Supported Item: Collation=On, Text=On, Tonescaling=On, Rotation=On
n Interpolation: NoMag=On, Bilin=On, Repl=On,Cubic Spline=On
n Format Types: Custom=On, Slide=On, Row Symmetric=On
n Format Types: 1, 2, 4, 6, 8, 9, 12, 15, 16, 20, 24, 30, 35=On
n Formatting: Aspect Ratio Mix Page=On, Image Size Mix in Std Fmt=On
n Formatting: DICOM Annotation Box=On, Req.Size Scale=On
n Formatting: Req.Size Mix in Row=On, Trim=On
n Formatting: Aspect Ratio Mix in Row=On, Image Size Mix in Row=On
n Formatting: Req.Image Size=On, Req.Size Mix on Page=On
n Formatting: True Landscape=On
n Formatting: Max Img Band=20, Max Band per Page=20, Max Img Col=0
n Formatting: Max Img Row=0, Min Horiz Sep=2, Min Vert Sep=2
n Formatting: Trim Width Enabled=2, Trim Width Disabled=0
n Formatting: Pixel Pitch=12.8205
n Image Processing: Grayscale=On, Minify=On, Max Image Dmax=3.1
n M952 Usage: Min H/V Mag=1, Max H/V Mag=64, Min Dmax 952=1.7
n on Configure, SCP Services, select the specific modality, Modify:
n PLUT=N, ToneScaling=PerceptionLUT (Always=Y)
n TFT/ULUT= Wrkstn2a.w87 (Always=Y), Contrast (dry)=2 (Always=N)
n Image Dmin=0.00 (Always=N), Image Dmax=3.00 (Always=N)
n Smoothing Type=11 (Always=N), Image Polarity=Normal (Always=N)
n NeventReports=Off (Always=Y), Warning Status=On
n Print Date=Off, Print Time=Off, Page Number=Off, Hosp.Name=Off
n Modality ID=Off, Annotation Override=Off (Always=N)
n Minify/Scale=On, Crop=Off, Text Box Relocation=None
n Print Priority=Normal (Always=N), Border=3.99 (Always=N)
n Film Base=Blue Film (Always=N), Film Size=11INx14IN (Always=N)
n Negotiate Color Print=Off
DICOM Network
RS422
COPCIL Board 9-pole Plug
Copper Cable Control 9-pin
Kodak DirectView
-DR 5100
-DR 7100
-DR 5000 Console Upgrade
-DR 9000 Console Upgrade Data 37-pin
MIM200 Setup:
n on Configure, Network:
n Node Name=MIM, IPAddr=accordingly
n Subnet Mask=accordingly, Gateway Addr=accordingly
n on Configure, Input, Network, Add:
n Protocol=DICOM 3.0, Log.Name=DICOM, Type/Com=Keypad/COM9
n on Configure, Destination, Add, Print, Direct, Qualified, 8100, Set:
n General: Log.Name=8100
n General: Database Name=8100, Model=8100, Memory=32
n Media Info: Media=35x43cm, 4096x5223, 5133, Blue
n Output Params: Cmd Set=952, Baud=1200, Data=8, Stop=1, Parity=Even
n Output Params: Pixel=12, Header/Line, Transfer=1000 KHz, Acquire=60
n Supported Item: Collation=On, Text=On, Tonescaling=On, Rotation=On
n Interpolation: NoMag=On, Bilin=On, Repl=On,Cubic Spline=On
n Format Types: Custom=On, Slide=On, Row Symmetric=On
n Format Types: 1, 2, 4, 6, 8, 9, 12, 15, 16, 20, 24, 30, 35=On
n Formatting: Aspect Ratio Mix Page=On, Image Size Mix in Std Fmt=On
n Formatting: DICOM Annotation Box=On, Req.Size Scale=On
n Formatting: Req.Size Mix in Row=On, Trim=On
n Formatting: Aspect Ratio Mix in Row=On, Image Size Mix in Row=On
n Formatting: Req.Image Size=On, Req.Size Mix on Page=On
n Formatting: True Landscape=On
n Formatting: Max Img Band=20, Max Band per Page=20, Max Img Col=0
n Formatting: Max Img Row=0, Min Horiz Sep=2, Min Vert Sep=2
n Formatting: Trim Width Enabled=2, Trim Width Disabled=0
n Formatting: Pixel Pitch=12.8205
n Image Processing: Grayscale=On, Minify=On, Max Image Dmax=3.1
n M952 Usage: Min H/V Mag=1, Max H/V Mag=64, Min Dmax 952=1.7
n on Configure, SCP Services, select the specific modality, Modify:
n PLUT=N, ToneScaling=PerceptionLUT (Always=Y)
n TFT/ULUT= Wrkstn2a.w87 (Always=Y), Contrast (dry)=2 (Always=N)
n Image Dmin=0.00 (Always=N), Image Dmax=3.00 (Always=N)
n Smoothing Type=11 (Always=N), Image Polarity=Normal (Always=N)
n NeventReports=Off (Always=Y), Warning Status=On
n Print Date=Off, Print Time=Off, Page Number=Off, Hosp.Name=Off
n Modality ID=Off, Annotation Override=Off (Always=N)
n Minify/Scale=On, Crop=Off, Text Box Relocation=None
n Print Priority=Normal (Always=N), Border=3.99 (Always=N)
n Film Base=Blue Film (Always=N), Film Size=14INx17IN (Always=N)
n Negotiate Color Print=Off
DICOM Network
Control 9 pin
Kodak DirectView COPCIL board
-DR 5100 Copper Cable
-DR 7100
-DR 5000 Console Upgrade Data 37 pin
-DR 9000 Console Upgrade
MIM200 Setup:
n on Configure, Network:
n Node Name=MIM, IPAddr=accordingly
n Subnet Mask=accordingly, Gateway Addr=accordingly
n on Configure, Input, Network, Add:
n Protocol=DICOM 3.0, Log.Name=DICOM, Type/Com=Keypad/COM9
n on Configure, Destination, Add, Print, Direct, Qualified, 8300, Set:
n General: Log.Name=8300
n General: Database Name=8300, Model=8300, Memory=32
n Media Info: Media=8x10in, 2256x2676, 2596, Blue
n Output Params: Cmd Set=952, Baud=1200, Data=8, Stop=1, Parity=Even
n Output Params: Pixel=8, Header/Line, Transfer=2000 KHz, Acquire=60
n Supported Item: Collation=On, Text=On, Tonescaling=On, Rotation=On
n Interpolation: NoMag=On, Bilin=On, Repl=On,Cubic Spline=On
n Format Types: Custom=On, Slide=On, Row Symm.=On, SuperSlide=On
n Format Types: 1, 2, 4, 6, 8, 9, 12, 15, 16, 20, 24, 30, 35=On
n Formatting: Aspect Ratio Mix Page=On, Image Size Mix in Std Fmt=On
n Formatting: DICOM Annotation Box=On, Req.Size Scale=On
n Formatting: Req.Size Mix in Row=On, Trim=On
n Formatting: Aspect Ratio Mix in Row=On, Image Size Mix in Row=On
n Formatting: Req.Image Size=On, Req.Size Mix on Page=On
n Formatting: True Landscape=On
n Formatting: Max Img Band=20, Max Band per Page=20, Max Img Col=0
n Formatting: Max Img Row=0, Min Horiz Sep=2, Min Vert Sep=2
n Formatting: Trim Width Enabled=2, Trim Width Disabled=0
n Formatting: Pixel Pitch=11.9048
n Image Processing: Grayscale=On, Minify=On, Max Image Dmax=3
n M952 Usage: Min H/V Mag=1, Max H/V Mag=16, Min Dmax 952=1.5
n on Configure, SCP Services, select the specific modality, Modify:
n PLUT=N, ToneScaling=PerceptionLUT (Always=Y)
n TFT/ULUT= wkstn83a.w8u (Always=Y), Contrast (dry)=1 (Always=N)
n Image Dmin=0.00 (Always=N), Image Dmax=3.00 (Always=N)
n Smoothing Type=4 (Always=N), Image Polarity=Normal (Always=N)
n NeventReports=Off (Always=Y), Warning Status=On
n Print Date=Off, Print Time=Off, Page Number=Off, Hosp.Name=Off
n Modality ID=Off, Annotation Override=Off (Always=N)
n Minify/Scale=On, Crop=Off, Text Box Relocation=None
n Print Priority=Normal (Always=N), Border=3.99 (Always=N)
n Film Base=Blue Film (Always=N), Film Size=8INx10IN (Always=N)
n Negotiate Color Print=Off
8300 Setup:
n on Operator Menu set: D=16, C=6, Sharp/Smooth=0 ie Auto
n on Operator Menu set: Film Layout: 1 on 1=Portrait
n on Service Menu set: Ratio=1.00, Serial=1200,8,1,Even,Comma,3M, Memory=16
n on Service Menu set: Digital Interface: Parity=Even, Modality Group=1
DICOM Network
Kodak DirectView
-DR 5100
-DR 7100 Crossed
-DR 5000 Console Upgrade Network Cable
-DR 9000 Console Upgrade
MIM200 Setup:
n on Configure, Network:
n Node Name=MIM, IPAddr=accordingly
n Subnet Mask=accordingly, Gateway Addr=accordingly
n on Configure, Input, Network, Add:
n Protocol=DICOM 3.0, Log.Name=DICOM, Type/Com=Keypad/COM9
n on Configure, Destination, Add, Print, Direct, Qualified, 8200, Set:
n General: Log.Name=8200, IPAddr=100.100.100.40,
n General: Database Name=8200, Model=8200, Memory=32
n Media Info: Media=35x43cm, 4361x5223, 5133, Any (Blue,Clear)
n Media Info: Media=35x35cm, 4361x4247, 4157, Any (Blue,Clear)
n Media Info: Media=11x14in, 3272x4361, 4271, Any (Blue,Clear)
n Supported Item: Collation=On, Common Text=On, Tonescaling=On
n Supported Item: Remote Image Deletion=On, Rotation=On
n Interpolation: No Magnification=On, Bilin=On, Repl=On
n Interpolation: Cubic Spline=On, Cubic Convolution 2=On
n Format Types: Custom=On, Row Symmetric=On
n Format Types: 1, 2, 4, 6, 8, 9, 12, 15, 16, 20, 24, 30, 35=On
n Formatting: Aspect Ratio Mix Page=On, Image Size Mix in Std Fmt=On
n Formatting: DICOM Annotation Box=On, Req.Size Scale=On
n Formatting: Req.Size Mix in Row=On, Trim=On
n Formatting: Aspect Ratio Mix in Row=On, Image Size Mix in Row=On
n Formatting: Req.Image Size=On, Req.Size Mix on Page=On
n Formatting: True Landscape=On
n Formatting: Max Img Band=20, Max Band per Page=20, Max Img Col=0
n Formatting: Max Img Row=0, Min Horiz Sep=2, Min Vert Sep=2
n Formatting: Trim Width Enabled=2, Trim Width Disabled=0
n Formatting: Pixel Pitch=12.8205
n Image Processing: Grayscale=On, Minify=On, Max Image Dmax=3.1
n SCU: Density Space= On, Variable Border=On, PLUT Service= On
n SCU: Curve Shape Tonescaling=On, Perception LUT Tonescaling=On
n M952 Usage: Min H/V Mag=1, Max H/V Mag=64, Min Dmax 952=1.7
n on Configure, SCP Services, select the specific modality, Modify:
n PLUT=N, ToneScaling=PerceptionLUT (Always=Y)
n TFT/ULUT= Wrkstn2a.w87 (Always=Y), Contrast (dry)=2 (Always=N)
n Image Dmin=0.00 (Always=N), Image Dmax=3.00 (Always=N)
n Smoothing Type=11 (Always=N), Image Polarity=Normal (Always=N)
n NeventReports=Off (Always=Y), Warning Status=On
n Print Date=Off, Print Time=Off, Page Number=Off, Hosp.Name=Off
n Modality ID=Off, Annotation Override=Off (Always=N)
n Minify/Scale=On, Crop=Off, Text Box Relocation=None
n Print Priority=Normal (Always=N), Border=3.99 (Always=N)
n Film Base=Blue Film (Always=N), Film Size=14INx17IN (Always=N)
n Negotiate Color Print=Off
DICOM Network
Control 9 pin
Kodak DirectView COPCIL board
-DR 5100 Copper Cable
-DR 7100
-DR 5000 Console Upgrade Data 37 pin
-DR 9000 Console Upgrade
MIM200 Setup:
n on Configure, Network:
n Node Name=MIM, IPAddr=accordingly
n Subnet Mask=accordingly, Gateway Addr=accordingly
n on Configure, Input, Network, Add:
n Protocol=DICOM 3.0, Log.Name=DICOM, Type/Com=Keypad/COM9
n on Configure, Destination, Add, Print, Direct, Qualified, 8610 (or 8600), Set:
n General: Log.Name=8610 (or 8600),
n General: Database=8610 (or 8600), Model=8610 (or 8600), Memory=32
n Media Info: Media=8x10in, 5025x6200, 6020, Blue
n Output Params: Cmd Set=952, Baud=1200, Data=8, Stop=1, Parity=Even
n Output Params: Pixel=12 (8 if 8600), Header/Line, Transfer=2000,Acq=60
n Supported Item: Collation=On, Text=On, Tonescaling=On, Rotation=On
n Interpolation: NoMag=On, Bilin=On, Repl=On,Cubic Spline=On
n Format Types: Custom=On, Slide=On, Row Symmetric=On
n Format Types: 1, 2, 4, 6, 8, 9, 12, 15, 16, 20, 24, 30, 35=On
n Formatting: Aspect Ratio Mix Page=On, Image Size Mix in Std Fmt=On
n Formatting: DICOM Annotation Box=On, Req.Size Scale=On
n Formatting: Req.Size Mix in Row=On, Trim=On
n Formatting: Aspect Ratio Mix in Row=On, Image Size Mix in Row=On
n Formatting: Req.Image Size=On, Req.Size Mix on Page=On
n Formatting: True Landscape=On
n Formatting: Max Img Band=20, Max Band per Page=20, Max Img Col=0
n Formatting: Max Img Row=0, Min Horiz Sep=2, Min Vert Sep=2
n Formatting: Trim Width Enabled=2, Trim Width Disabled=0
n Formatting: Pixel Pitch=25.8065
n Image Processing: Grayscale=On, Minify=On, Max Image Dmax=3.5
n M952 Usage: Min H/V Mag=0.26, Max H/V Mag=16, Min Dmax 952=2
n on Configure, SCP Services, select the specific modality, Modify:
n PLUT=N, ToneScaling=PerceptionLUT (Always=Y)
n TFT/ULUT= upmsv3kp.w8u (Always=N), Contrast (dry)=6 (Always=Y)
n Modality Group=1, Conv.Group=1, Gamma Table=Linear in Density
n Image Dmin=0.00 (Always=N), Image Dmax=3.50 (Always=Y)
n Smoothing Type=1 (Always=Y), Image Polarity=Normal (Always=N)
n NeventReports=Off (Always=Y), Warning Status=On
n Print Date=Off, Print Time=Off, Page Number=Off, Hosp.Name=Off
n Modality ID=Off, Annotation Override=Off (Always=N)
n Minify/Scale=On, Crop=Off, Text Box Relocation=None
n Print Priority=Normal (Always=N), Border=3.99 (Always=N)
n Film Base=Blue Film (Always=N), Film Size=8INx10IN (Always=N)
n Negotiate Color Print=Off
8610 Setup: on 8610 Operator Menu into Test Menu, Software Version, verify:
n Imager=2.4, VRTX32=1.08, Contrast=6.P.2, Conv.Kernel=M.1.0
DICOM Network
Kodak DirectView
-DR 5100
-DR 7100
-DR 5000 Console Upgrade
-DR 9000 Console Upgrade
8900 Setup:
n on Configuration, System, Network:
n Host Name=DV8900, IPAddr=accordingly
n Subnet Mask=accordingly, Gateway Addr=accordingly
n on Configuration, DICOM SCP, Communications:
n Port=5040, Association Limit=12, Source Name=DICOM
n on Configuration, Destination:
n General: Log.Name=8900
n Media Types: Media=35x43cm, 9100x11037, 10781, Any
n Media Types: Media=35x35cm,9100x9087, 8831, Any
n Media Types: Media=11x14in, 7137x9100, 8844, Any
n Media Types: Media=10x12in, 6490x7767, 7511, Any
n Media Types: Media=8x10in, 5167x6490, 6234, Any
n Formatting: Aspect Ratio Mix Page=On, Aspect Ratio Mix Row=On
n Formatting: Image Size Mix in Std Fmt=On, Image Size Mix Row=On
n Formatting: DICOM Annotation Box=On, Req.Image Size=On
n Formatting: Req.Size Scale=On, Req.Size Mix Page=On
n Formatting: Req.Size Mix Row=On, Trim=On,
n Formatting: True Landscape=On, Rotation=On
n Formatting: Minify/Crop=On, Tonescaling on Image Basis=On
n Formatting: Max Img Band=7, Max Band Page=7, Max Img Cols=0
n Formatting: Max Img Rows=0, Pixel Pitch=25.5910, Min Horiz Sep=4
n Formatting: Min Vert Sep=4, Trim Width Enabled=4
n Formatting: Trim Width Disabled=0, Maximum DMAX=3.30
n on Configuration, DICOM SCP, SCP Services, select specific modality, Modify:
n Negotiate Presentation LUT=No, Negotiate Color Print=No
n TFT= Wrkstn2a.w87 (Always=N), Contrast=2 (Always=N)
n Smoothing Type=11 (Always=N), Image Polarity=Normal (Always=N)
n Image Dmin=0.00 (Always=N), Image Dmax=3.00 (Always=N)
n NeventReports=No (Always=Y), Warnings=Yes
n Print Priority=Normal (Always=N), Border=3.99 (Always=N)
n 2mm Border=Yes, Film Clip Border=No, Film Base=Blue Film (Always=N)
n Film Size=14INx17IN (Always=N), Sorter Bin=Bin1 (Always=N)
n Print Date=No, Print Time=No, Page Nbr=No, Hosp.Name=No
n Modality ID=No, Annotation Override=No, Density Patch=No
n Image Resizing=Minify/Scale (Always=N),
n Text Box Location=None, Source ID=dr
DICOM Network
Kodak DirectView
-DR 5100
-DR 7100
-DR 5000 Console Upgrade
-DR 9000 Console Upgrade
8150 Setup:
n on Configuration, System, Network:
n Host Name=DV8150DRE, IPAddr=accordingly
n Subnet Mask=accordingly, Gateway Addr=accordingly
n on Configuration, DICOM SCP, Communications:
n Port=5040, Association Limit=12, Source Name=DICOM
n on Configuration, Destination:
n AE Title: Log.Name=DV8150
n Media Types: Media=35x43cm, 4438x5390, 5262, Any
n Media Types: Media=35x35cm, 4438x4414,4286, Any
n Media Types: Media=11x14in, 3440x4438, 4310, Any
n Formatting: Aspect Ratio Mix Page=On, Aspect Ratio Mix Row=On
n Formatting: Image Size Mix in Std Fmt=On, Image Size Mix Row=On
n Formatting: DICOM Annotation Box=On, Req.Image Size=On
n Formatting: Req.Size Scale=On, Req.Size Mix Page=On
n Formatting: Req.Size Mix Row=On, Trim=On,
n Formatting: True Landscape=On, Rotation=On
n Formatting: Minify/Crop=On, Tonescaling on Image Basis=On
n Formatting: Max Img Band=7, Max Band Page=7, Max Img Cols=0
n Formatting: Max Img Rows=0, Pixel Pitch=12.8000, Min Horiz Sep=2
n Formatting: Min Vert Sep=2, Trim Width Enabled=2
n Formatting: Trim Width Disabled=0, Maximum DMAX=3.10
n on Configuration, DICOM SCP, SCP Services, select specific modality, Modify:
n Negotiate Presentation LUT=No, Negotiate Color Print=No,
n TFT Set Name=Wrkstn2a.w87 (Always=Y)
n Contrast=1 (Always=N), Smoothing Type=5 (Always=N)
n Dmin=0.00 (Always=N), Dmax=3.00 (Always=N)
n Image Polarity=Normal (Always=N)
n NeventReports=No (Always=Y), Warnings=Yes
n Print Priority=Normal (Always=N), Border=3.99 (Always=N)
n 2mm Border=Yes, Film Clip Border=No,
n Film Base=Blue Film (Always=N), Film Size=14INx17IN (Always=N)
n Print Date=No, Print Time=No, Page Nbr=No, Hosp.Name=No,
n Modality ID=No, Annotation Override=No, Density Patch=No
n Image Resizing=Minify/Scale (Always=N),
n Text Box Location=None, Source ID=dr
DICOM Network
Kodak DirectView
-DR 5100
-DR 7100
-DR 5000 Console Upgrade
-DR 9000 Console Upgrade
Kodak CMI 1000
CMI-1000 Setup:
at Local Panel, under Media, set A4 or Letter ie what inside Paper Tray
(CMI-1000 sw considers only this field and uses it as A4 or Letter (Always=Y):
at Local Panel, under Menu, Imager Setup:
n Network Setup:
n IPAddr=accordingly, Subnet Mask=accordingly, Gateway=accordingly
n under More Settings: DICOM Port=5040
n Edit Host Name/AE Title=CMI1000
n Modality (SCU) Config (or after modality recognition):
n Select Modality=accordingly, Modality Config.Assistant=Yes, Reset Config=No
n Note: Color IQ settings used when images sent with Color DICOM SOP
n under Image Quality, Color Image Quality: (no need to adjust, leave defaults)
n Match Monitor Colors=default ie sRGB Color Space Profile.icm
n Adjust Color Tones=default ie Default_Contrast_100.icm
n Note: Grayscale IQ settings used when images sent with Grayscale DICOM SOP:
n under Image Quality, Grayscale Image Quality:
n Contrast=7 (Always=Y)
n TFT Set (From list)=Wrkstn2a.w87 (Always=Y)
n Wet Contrast=0 (Always=N), Curve Shape=429 (Always=N)
n under More Quality Settings:
n Tonescaling=Presentation LUT (Always=N),
n Image Dmax=220 (Always=N), Image Dmin=10 (Always=N)
n Smoothing=11 (Always=Y), Polarity=Positive (Always=N)
n Interpolation=CUBIC (Always=N), Trim=No (Always=N)
n Page Orientation=PORTRAIT (Always=N), Negotiate PLUT=No
n under Modality Defaults:
n Media Size=8.5x11 (Always=N), don’t care, this field plays no role
n Image Resizing=Minify (Always=N),
n Priority=Normal (Always=N), NeventReports=No (Always=Y),
n Warnings=Yes, Color=Yes
n (set Color=No when only b/w images are printed and set it to be sure
n to apply to the b/w images the Greyscale Image Quality settings)
n Page Annotation:
n Hosp.Name=No, Modality ID=No, Page Nbr=No, Date=No, Time= No
n Save Changes and Exit
1
setup valid also for Kodak PACS LINK 25 PRINT SERVER.
DICOM Network
iew
00 DryV
3M 87
Kodak AutoRad NT
Fiber Cable
Fiber Cable
AutoRad Setup:
n insert into file C:\WINNT\system32\drivers\etc\hosts:
n IPaddress of 9410 Computer Name of 9410 e.g., plink
n click Report Tool button
n into menu Print film/Select Printer/New set:
n Name=DV8700, Description=DV8700, AE=9410
n Host=Computer Name of 9410 e.g., plink, Port=1024
n Timeout=120, BitDepth=12
n Select Formats=click all formats
n Set: 1x1=4096,5195, 1x2=4096,2594; 2x2=2048,2594, 2x3=2048,1727
n Set: 3x3=1365,1727, 3x4=1365,1294; 3x5=1365,1034, 4x4=1024, 1294
n Set: 4x5=1024,1034
n Click OK to return
n Click Image Quality Calibration/Print Test Pattern to calibrate the printer
n Measure densities and enter averaged values in Calibration table
n Click OK to return and print a film to verify Calibration is done correctly
n Note: Calibration must be redone at every printer service or TFT change
9410 Setup:
n on Device Setup, LOCAL PRINTERS:
n Printer=8700, Model=8700, Output=Fiber
n Baud=19200, Parity=None, Data=8, Stop=1, Command Set=Superset
n Pixel=12, Header/Line, Timeout=60, Transfer Rate=2 MHz
n Film Mismatch=Print Always, Interpolation Type=831
n Interp Num=5, Max.Density=300, Contrast=6, Border Density=0
n TFT/ULUT Emulation=On, Installed TFT/ULUT=Ver693c0.w87
n on Device Setup, SCP PRINTERS, Current Providers:
n Printer=8700, AE Title=9410, Port=1024, Max Associations=5
n on Device Setup, SCP PRINTERS, Registered Users:
n SCU AETitle=accordingly, SCU IPAddr=accordingly, SCP=8700
n Copies=1, Contrast Table=9, TFT/ULUT=Pmsv3k.w87
n Max.Density=300, Border Density=0, Mag.Type=8, Smoothing=2
n Polarity=1, Orientation=1, Set Req.Image Size=No, Priority=Low
n Interceptor=Yes, N-Event-Print Job=No, N-Event Printer=No
n Trim=No, Attribute Warning=No
n Contrast Test Mode=No, Contrast Test Mode Density=0
DICOM Network
iew
00 DryV
3M 87
Kodak AutoRad NT
Fiber Cable
Fiber Cable
AutoRad Setup:
n insert into file C:\WINNT\system32\drivers\etc\hosts:
n IPaddress of 9410 Computer Name of 9410 e.g., plink
n click Report Tool button
n into menu Print film/Select Printer/New set:
n Name=DV8500, Description=DV8500, AE=9410
n Host=Computer Name of 9410 e.g., plink, Port=1024
n Timeout=120, BitDepth=12
n Select Formats=click all formats
n Set: 1x1=3380,4280, 1x2=3380,2132; 2x2=1690,2132, 2x3=1690,1420
n Set: 3x3=1126,1420, 3x4=1126,1060; 3x5=1126,848, 4x4=845,1060
n Set: 4x5=845,848
n Click OK to return
n Click Image Quality Calibration/Print Test Pattern to calibrate the printer
n Measure densities and enter averaged values in Calibration table
n Click OK to return and print a film to verify Calibration is done correctly
n Note: Calibration must be redone at every printer service or TFT change
9410 Setup:
n on Device Setup, LOCAL PRINTERS:
n Printer=8500, Model=8500, Output=Fiber
n Baud=19200, Parity=None, Data=8, Stop=1, Command Set=Superset
n Pixel=12, Header/Line, Timeout=60, Transfer Rate=2 MHz
n Film Mismatch=Print Always, Interpolation Type=831
n Interp Num=5, Max.Density=300, Contrast=6, Border Density=0
n TFT/ULUT Emulation=On, Installed TFT/ULUT=Ver693c0.w87
n on Device Setup, SCP PRINTERS, Current Providers:
n Printer=8500, AE Title=9410, Port=1024, Max Associations=5
n on Device Setup, SCP PRINTERS, Registered Users:
n SCU AETitle=accordingly, SCU IPAddr=accordingly, SCP=8500
n Copies=1, Contrast Table=9, TFT/ULUT=Pmsv3k.w87
n Max.Density=300, Border Density=0, Mag.Type=8, Smoothing=2
n Polarity=1, Orientation=1, Set Req.Image Size=No, Priority=Low
n Interceptor=Yes, N-Event-Print Job=No, N-Event Printer=No
n Trim=No, Attribute Warning=No
n Contrast Test Mode=No, Contrast Test Mode Density=0
DICOM Network
RS422
COPCIL Board 9-pole Plug
Copper Cable Control 9-pin
Kodak AutoRad NT
Data 37-pin
AutoRad Setup:
n insert into file C:\WINNT\system32\drivers\etc\hosts:
n IPaddress of 9410 Computer Name of 9410 e.g., plink
n click Report Tool button
n into menu Print film/Select Printer/New set:
n Name=DV8100, Description=DV8100, AE=9410
n Host=Computer Name of 9410 e.g., plink, Port=1024
n Timeout=120, BitDepth=12
n Select Formats=click all formats
n Select Formats=click all formats
n Set: 1x1=4096,5195, 1x2=4096,2594; 2x2=2048,2594, 2x3=2048,1727
n Set: 3x3=1365,1727, 3x4=1365,1294; 3x5=1365,1034, 4x4=1024, 1294
n Set: 4x5=1024,1034
n Click OK to return
n Click Image Quality Calibration/Print Test Pattern to calibrate the printer
n Measure densities and enter averaged values in Calibration table
n Click OK to return and print a film to verify Calibration is done correctly
n Note: Calibration must be redone at every printer service or TFT change
9410 Setup:
on Device Setup, LOCAL PRINTERS:
n Printer=8100, Model=8100 4096 pxls/line, Output=Copper
n Baud=1200, Parity=Even, Data=8, Stop=1, Command Set=952
n Pixel=12, Header/Line, Timeout=60, Transfer Rate=1 MHz
n Film Mismatch=Print Always, Interpolation Type=831
n Interp Num=5, Max.Density=300, Contrast=6, Border Density=0
n TFT/ULUT Emulation=On, Installed TFT/ULUT=Ver693c0.w87
on Device Setup, SCP PRINTERS, Current Providers:
n Printer=8100, AE Title=9410, Port=1024, Max Associations=5
on Device Setup, SCP PRINTERS, Registered Users:
n SCU AETitle=accordingly, SCU IPAddr=accordingly
n SCP=8100, Copies=1, Contrast Table=9, TFT/ULUT=Pmsb.w87
n Max.Density=300, Border Density=0, Mag.Type=8, Smoothing=2
n Polarity=1, Orientation=1, Set Req.Image Size=No, Priority=Low
n Interceptor=Yes, N-Event-Print Job=No, N-Event Printer=No
n Trim=No, Attribute Warning=No
n Contrast Test Mode=No, Contrast Test Mode Density=0
DICOM Network
Control 9 pin
Kodak AutoRad NT COPCIL board
Copper Cable
Data 37 pin
Requirements: AutoRad NT v4.2, 9410 v1.6, 8300 v4.9.1, 8300 LUT v3.0.3B
AutoRad Setup:
n insert into file C:\WINNT\system32\drivers\etc\hosts:
n IPaddress of 9410 Computer Name of 9410 e.g., plink
n click Report Tool button
n into menu Print film/Select Printer/New set:
n Name=DV8100, Description=DV8100, AE=9410
n Host=Computer Name of MIM200 e.g., plink, Port=1024
n Timeout=120, BitDepth=8
n Select Formats=click only formats
n 1x1=2256,2676, 1x2=2256,1326; 2x2=1116,1326, 2x3=1116,879
n Click OK to return
n Click Image Quality Calibration/Print Test Pattern to calibrate the printer
n Measure densities and enter averaged values in Calibration table
n Click OK to return and print a film to verify Calibration is done correctly
n Note: Calibration must be redone at every printer service or TFT change
9410 Setup:
n on Device Setup, LOCAL PRINTERS:
n Printer=8300, Model=8300 Copper, Output=Copper
n Command Set=952, Baud=1200, Data=8, Stop=1, Parity=Even
n Pixel=8, Header/Line, Timeout=60, Transfer Rate=1 MHz
n Film Mismatch=Print Always, Interpolation Type=831
n Interp Num=0, Max.Density=300, Contrast=6, Border Density=0
n TFT/ULUT Emulation=On, Installed TFT/ULUT= upmsv3k.w8u
n on Device Setup, SCP PRINTERS, Current Providers:
n Printer=8300, AE Title=9410, Port=1024, Max Associations=5
n on Device Setup, SCP PRINTERS, Registered Users:
n SCU AETitle=accordingly, SCU IPAddr=accordingly
n SCP=8300, Copies=1, Contrast Table=10, TFT/ULUT=u1_109b.w8u
n Max.Density=300, Border Density=0, Mag.Type=8, Smoothing=0
n Polarity=1, Orientation=1, Set Req.Image Size=No, Priority=Low
n Interceptor=Yes, N-Event-Print Job=No, N-Event Printer=No
n Trim=No, Attribute Warning=No
n Contrast Test Mode=No, Contrast Test Mode Density=0
8300 Setup:
n on Operator Menu set: D=16, C=6, Sharp/Smooth=0 i.e., Auto
n on Operator Menu set: Film Layout: 1 on 1=Portrait
n on Service Menu set: Ratio=1.00, Serial=1200,8,1,Even,Comma,3M, Memory=16
n on Service Menu set: Digital Interface: Parity=Even, Modality Group=1
DICOM Network
AutoRad Setup:
n insert into file C:\WINNT\system32\drivers\etc\hosts:
n IPaddress of MLP190 Computer Name of 190 e.g., mlp
n click Report Tool button
n into menu Print film/Select Printer/New set:
n Name=K190, Description=K190, AE=190
n Host=Computer Name of MIM200 e.g., mim, Port=5040
n Timeout=120, BitDepth=12
n Select Formats=click all formats
n Click OK to return
n Click Image Quality Calibration/Print Test Pattern to calibrate the printer
n Measure densities and enter averaged values in Calibration table
n Click OK to return and print a film to verify Calibration is done correctly
n Note: Calibration must be redone at every printer service or TFT change
190 Setup:
n On 190 Control Panel press Menu, Setup:
n Printer Density=3.00, Curve Shape=3.0, Contrast=0, Contrast Pivot Density=1.2
n IPAddress=accordingly, Subnet Mask=accordingly, Gateway Address=accordingly
n Port=5040, Network Node Name=mlp, Connection Type=RJ45
DICOM Network
Kodak AutoRad NT
Kodak 2180 camera
Fiber Cable
AutoRad Setup:
n insert into file C:\WINNT\system32\drivers\etc\hosts:
n IPaddress of MIM200 Computer Name of MIM200 e.g., mim
n click Report Tool button
n into menu Print film/Select Printer/New set:
n Name=K2180, Description=K2180, AE=2180
n Host=Computer Name of MIM200 e.g., mim, Port=5040
n Timeout=120, BitDepth=12
n Select Formats=click all formats
n Click OK to return
n Click Image Quality Calibration/Print Test Pattern to calibrate the printer
n Measure densities and enter averaged values in Calibration table
n Click OK to return and print a film to verify Calibration is done correctly
n Note: Calibration must be redone at every printer service or TFT change
MIM200 Setup:
n on Configure, Network:
n Computer Name=mim, IPAddr=accordingly
n Subnet Mask=accordingly, Gateway Addr=accordingly
n on Configure, Input, Network, Add:
n Protocol=DICOM 3.0, Log.Name=DICOM, Type/Com=Keypad/COM9
n on Configure, Destination, Add, Print, Direct, Qualified, KELP 2180, Set:
n General: Log.Name=KELP2180, Database Name=KELP 2180
n General: Model=KELP 2180, Memory=24, Node ID=6 or accordingly
n Media Info: Media=35x43cm, 4136x5160, 5030, (Blue)
n Media Info:Media=35x35cm,4136x4136,4006, (Blue)
n Media Info: Media=11x14in, 3240x4136, 4006, (Blue)
n Media Info: Media=8x10in, 2290x2840, 2710, (Blue)
n Supported Item: Collation=On, Text=On, Tonescaling=On, Rotation=On
n Interpolation: NoMag=On, Bil=On, Repl=On,Cubic=On, Cubic 2=On
2180 Setup:
n Optical Interface board will automatic configure into 2180, no setup needed
DICOM Network
Kodak AutoRad NT
Kodak 1120 camera
Fiber Cable
AutoRad Setup:
n insert into file C:\WINNT\system32\drivers\etc\hosts:
n IPaddress of MIM200 Computer Name of MIM200 e.g., mim
n click Report Tool button
n into menu Print film/Select Printer/New set:
n Name=K1120, Description=K1120, AE=1120
n Host=Computer Name of MIM200 e.g., mim, Port=5040
n Timeout=120, BitDepth=12
n Select Formats=click all formats
n Click OK to return
n Click Image Quality Calibration/Print Test Pattern to calibrate the printer
n Measure densities and enter averaged values in Calibration table
n Click OK to return and print a film to verify Calibration is done correctly
n Note: Calibration must be redone at every printer service or TFT change
MIM200 Setup:
n on Configure, Network:
n Computer Name=mim, IPAddr=accordingly
n Subnet Mask=accordingly, Gateway Addr=accordingly
n on Configure, Input, Network, Add:
n Protocol=DICOM 3.0, Log.Name=DICOM, Type/Com=Keypad/COM9
n on Configure, Destination, Add, Print, Direct, Qualified, KELP 1120, Set:
n General: Log.Name=KELP1120, Database Name=KELP 1120
n General: Model=KELP 1120, Memory=20, Node ID=6 or accordingly
n Media Info: Media=35x43cm, 4096x5132, 5034, (Blue)
n Media Info: Media=35x35cm, 4096x4108, 4010, (Blue)
n Media Info: Media=11x14in, 4096x3232, 3134, (Blue)
n Media Info: Media=8x10in, 2304x2900, 2802, (Blue)
n Supported Item: Collation=On, Text=On, Tonescaling=On, Rotation=On
1120 Setup:
n Optical Interface board will automatic configure into 1120, no setup needed
DICOM Network
Kodak AutoRad NT
Kodak 160 camera
Crossed
Network Cable
AutoRad Setup:
n insert into file C:\WINNT\system32\drivers\etc\hosts:
n IPaddress of MIM200 Computer Name of MIM200 e.g., mim
n click Report Tool button
n into menu Print film/Select Printer/New set:
n Name=K160, Description=K160, AE=160
n Host=Computer Name of MIM200 e.g., mim, Port=5040
n Timeout=120, BitDepth=12
n Select Formats=click all formats
n Click OK to return
n Click Image Quality Calibration/Print Test Pattern to calibrate the printer
n Measure densities and enter averaged values in Calibration table
n Click OK to return and print a film to verify Calibration is done correctly
n Note: Calibration must be redone at every printer service or TFT change
MIM200 Setup:
n on Configure, Network:
n Computer Name=mim, IPAddr=accordingly
n Subnet Mask=accordingly, Gateway Addr=accordingly
n on Configure, Input, Network, Add:
n Protocol=DICOM 3.0, Log.Name=DICOM, Type/Com=Keypad/COM9
n on Configure, Destination, Add, Print, Direct, Qualified, KELI 160, Set:
n General: Log.Name=KELI 160, IPAddr=100.100.100.30,
n General: Database Name=KELI 160, Model=KELI 160
n Media Info: Media=35x43cm, 4361x5348, 5228, Any (Blue,Clear)
n Supported Item: Collation=On, Text=On, Tonescaling on Image=On
n Supported Item: Pivot Density=On, Rotation=On
n Interpolation: NoMag=On, Bil=On, Repl=On,Cubic=On, Cubic 2=On
n Format Types: Custom=On, Slide=On, Row Symmetric=On
DICOM Network
iew
00 DryV
3M 87
Kodak AutoRad NT
Fiber Cable
Fiber Cable
AutoRad Setup:
n insert into file C:\WINNT\system32\drivers\etc\hosts:
n IPaddress of MIM200 Computer Name of MIM200 e.g., mim
n click Report Tool button
n into menu Print film/Select Printer/New set:
n Name=DV8700, Description=DV8700, AE=8700
n Host=Computer Name of MIM200 e.g., mim, Port=5040
n Timeout=120, BitDepth=12
n Select Formats=click all formats
n Select Formats=click all formats
n Set: 1x1=4096,5195, 1x2=4096,2594; 2x2=2048,2594, 2x3=2048,1727
n Set: 3x3=1365,1727, 3x4=1365,1294; 3x5=1365,1034, 4x4=1024, 1294
n Set: 4x5=1024,1034
n Click OK to return
n Click Image Quality Calibration/Print Test Pattern to calibrate the printer
n Measure densities and enter averaged values in Calibration table
n Click OK to return and print a film to verify Calibration is done correctly
n Note: Calibration must be redone at every printer service or TFT change
MIM200 Setup:
n on Configure, Network:
n Node Name=mim, IPAddr=accordingly
n Subnet Mask=accordingly, Gateway Addr=accordingly
n on Configure, Input, Network, Add:
n Protocol=DICOM 3.0, Log.Name=DICOM, Type/Com=Keypad/COM9
n on Configure, Destination, Add, Print, Direct, Qualified, 8700, Set:
n General: Log.Name=8700
n General: Database Name=8700, Model=8700, Memory=32
n Media Info: Media=35x43cm, 4096x5223, 5133, Blue
n Output Params: Cmd=SuperSet,Baud=19200,Data=8,Stop=1,Parity=None
n Output Params: Pixel=12, Header/Line, Transfer=2000 KHz, Acq=60
n Supported Item: Collation=On, Text=On, Tonescaling=On, Rotation=On
n Interpolation: NoMag=On, Bilin=On, Repl=On,Cubic Spline=On
n Format Types: Custom=On, Slide=On, Row Symmetric=On
n Format Types: 1, 2, 4, 6, 8, 9, 12, 15, 16, 20, 24, 30, 35=On
n Formatting: Aspect Ratio Mix on Page=On, Image Size Mix in Std Fmt=On
n Formatting: DICOM Annotation Box=On, Req.Size Scale=On
n Formatting: Req.Size Mix in Row=On, Trim=On
n Formatting: Aspect Ratio Mix in Row=On, Image Size Mix in Row=On
n Formatting: Req.Image Size=On, Req.Size Mix on Page=On
n Formatting: True Landscape=On
n Formatting: Max Img per Band=20, Max Band per Page=20, Max Img Col=0
n Formatting: Max Img Row=0, Min Horiz Sep=2, Min Vert Sep=2
n Formatting: Trim Width Enabled=2, Trim Width Disabled=0
n Formatting: Pixel Pitch=12.8205
n Image Processing: Grayscale=On, Minify=On, Max Image Dmax=3.1
n M952 Usage: Min H/V Mag=1, Max H/V Mag=64, Min Dmax 952=1.7
n on Configure, SCP Services, select the specific modality, Modify:
n PLUT=N, ToneScaling=PerceptionLUT (Always=Y)
n TFT/ULUT=Pmsv3k.w87 (Always=Y), Contrast (dry)=9 (Always=N)
n Image Dmin=0.00 (Always=N), Image Dmax=3.00 (Always=N)
n NeventReports=Off (Always=Y), Warning Status=On
n Print Date=Off, Print Time=Off, Page Number=Off, Hosp.Name=Off
n Modality ID=Off, Annotation Override=Off (Always=N)
n Print Priority=Normal (Always=N), Image Polarity=Normal (Always=N)
n Smoothing Type=2 (Always=N)
n Border=Black (Always=N), Film Base=Blue Film (Always=N)
n Film Size=14INx17IN (Always=N), Negotiate Color Print=Off
DICOM Network
iew
00 DryV
3M 87
Kodak AutoRad NT
Fiber Cable
Fiber Cable
AutoRad Setup:
n insert into file C:\WINNT\system32\drivers\etc\hosts:
n IPaddress of MIM200 Computer Name of MIM200 e.g., mim
n click Report Tool button
n into menu Print film/Select Printer/New set:
n Name=DV8500, Description=DV8500, AE=8500
n Host=Computer Name of MIM200 e.g., mim, Port=5040
n Timeout=120, BitDepth=12
n Select Formats=click all formats
n Set: 1x1=3380,4280, 1x2=3380,2132; 2x2=1690,2132, 2x3=1690,1420
n Set: 3x3=1126,1420, 3x4=1126,1060; 3x5=1126,848, 4x4=845,1060
n Set: 4x5=845,848
n Click OK to return
n Click Image Quality Calibration/Print Test Pattern to calibrate the printer
n Measure densities and enter averaged values in Calibration table
n Click OK to return and print a film to verify Calibration is done correctly
n Note: Calibration must be redone at every printer service or TFT change
MIM200 Setup:
n on Configure, Network:
n Node Name=mim, IPAddr=accordingly
n Subnet Mask=accordingly, Gateway Addr=accordingly
n on Configure, Input, Network, Add:
n Protocol=DICOM 3.0, Log.Name=DICOM, Type/Com=Keypad/COM9
n on Configure, Destination, Add, Print, Direct, Qualified, 8500, Set:
n General: Log.Name=8500
n General: Database Name=8500, Model=8500, Memory=32
n Media Info: Media=11x14in, 3388x4283, 4193, Blue
n Output Params: Cmd=SuperSet,Baud=19200,Data=8,Stop=1,Parity=None
n Output Params: Pixel=12, Header/Line, Transfer=2000 KHz, Acq=60
n Supported Item: Collation=On, Text=On, Tonescaling=On, Rotation=On
n Interpolation: NoMag=On, Bilin=On, Repl=On,Cubic Spline=On
n Format Types: Custom=On, Slide=On, Row Symmetric=On
n Format Types: 1, 2, 4, 6, 8, 9, 12, 15, 16, 20, 24, 30, 35=On
n Formatting: Aspect Ratio Mix on Page=On, Image Size Mix in Std Fmt=On
n Formatting: DICOM Annotation Box=On, Req.Size Scale=On
n Formatting: Req.Size Mix in Row=On, Trim=On
n Formatting: Aspect Ratio Mix in Row=On, Image Size Mix in Row=On
n Formatting: Req.Image Size=On, Req.Size Mix on Page=On
n Formatting: True Landscape=On
n Formatting: Max Img per Band=20, Max Band per Page=20, Max Img Col=0
n Formatting: Max Img Row=0, Min Horiz Sep=2, Min Vert Sep=6
n Formatting: Trim Width Enabled=2, Trim Width Disabled=0
n Formatting: Pixel Pitch=12.8205
n Image Processing: Grayscale=On, Minify=On, Max Image Dmax=3.1
n M952 Usage: Min H/V Mag=1, Max H/V Mag=64, Min Dmax 952=1.7
n on Configure, SCP Services, select the specific modality, Modify:
n PLUT=N, ToneScaling=PerceptionLUT (Always=Y)
n TFT/ULUT=Pmsv3k.w87 (Always=Y), Contrast (dry)=9 (Always=N)
n Image Dmin=0.00 (Always=N), Image Dmax=3.00 (Always=N)
n NeventReports=Off (Always=Y), Warning Status=On
n Print Date=Off, Print Time=Off, Page Number=Off, Hosp.Name=Off
n Modality ID=Off, Annotation Override=Off (Always=N)
n Print Priority=Normal (Always=N), Image Polarity=Normal (Always=N)
n Smoothing Type=2 (Always=N)
n Border=Black (Always=N), Film Base=Blue Film (Always=N)
n Film Size=11INx14IN (Always=N), Negotiate Color Print=Off
DICOM Network
RS422
COPCIL Board 9-pole Plug
Copper Cable Control 9-pin
Kodak AutoRad NT
Data 37-pin
AutoRad Setup:
n insert into file C:\WINNT\system32\drivers\etc\hosts:
n IPaddress of MIM200 Computer Name of MIM200 e.g., mim
n click Report Tool button
n into menu Print film/Select Printer/New set:
n Name=DV8100, Description=DV8100, AE=8100
n Host=Computer Name of MIM200 e.g., mim, Port=5040
n Timeout=120, BitDepth=12
n Select Formats=click all formats
n Select Formats=click all formats
n Set: 1x1=4096,5195, 1x2=4096,2594; 2x2=2048,2594, 2x3=2048,1727
n Set: 3x3=1365,1727, 3x4=1365,1294; 3x5=1365,1034, 4x4=1024, 1294
n Set: 4x5=1024,1034
n Click OK to return
n Click Image Quality Calibration/Print Test Pattern to calibrate the printer
n Measure densities and enter averaged values in Calibration table
n Click OK to return and print a film to verify Calibration is done correctly
n Note: Calibration must be redone at every printer service or TFT change
MIM200 Setup:
n on Configure, Network:
n Node Name=mim, IPAddr=accordingly
n Subnet Mask=accordingly, Gateway Addr=accordingly
n on Configure, Input, Network, Add:
n Protocol=DICOM 3.0, Log.Name=DICOM, Type/Com=Keypad/COM9
n on Configure, Destination, Add, Print, Direct, Qualified, 8100, Set:
n General: Log.Name=8100
n General: Database Name=8100, Model=8100, Memory=32
DICOM Network
Control 9 pin
Kodak AutoRad NT COPCIL board
Copper Cable
Data 37 pin
Requirements: AutoRad NT v4.2, MIM200 v6.1, 8300 v4.9.1, 8300 LUT v3.0.3B
Note: This setup is basically also valid for 25 PS computer
AutoRad Setup:
n insert into file C:\WINNT\system32\drivers\etc\hosts:
n IPaddress of MIM200 Computer Name of MIM200 e.g., mim
n click Report Tool button
n into menu Print film/Select Printer/New set:
n Name=DV8300, Description=DV8300, AE=8300
n Host=Computer Name of MIM200 e.g., mim, Port=5040
n Timeout=120, BitDepth=8
n Select Formats=click only formats
n 1x1=2256,2676, 1x2=2256,1326; 2x2=1116,1326, 2x3=1116,879
n Click OK to return
n Click Image Quality Calibration/Print Test Pattern to calibrate the printer
n Measure densities and enter averaged values in Calibration table
n Click OK to return and print a film to verify Calibration is done correctly
n Note: Calibration must be redone at every printer service or TFT change
MIM200 Setup:
n on Configure, Network:
n Node Name=mim, IPAddr=accordingly
n Subnet Mask=accordingly, Gateway Addr=accordingly
n on Configure, Input, Network, Add:
n Protocol=DICOM 3.0, Log.Name=DICOM, Type/Com=Keypad/COM9
n on Configure, Destination, Add, Print, Direct, Qualified, 8300, Set:
n General: Log.Name=8300
n General: Database Name=8300, Model=8300, Memory=32
n Media Info: Media=8x10in, 2256x2676, 2596, Blue
n Output Params: Cmd Set=952, Baud=1200, Data=8, Stop=1, Parity=Even
n Output Params: Pixel=8, Header/Line, Transfer=2000 KHz, Acquire=60
8300 Setup:
n on Operator Menu set: D=16, C=6, Sharp/Smooth=0 i.e., Auto
n on Operator Menu set: Film Layout: 1 on 1=Portrait
n on Service Menu set: Ratio=1.00, Serial=1200,8,1,Even,Comma,3M, Memory=16
n on Service Menu set: Digital Interface: Parity=Even, Modality Group=1
DICOM Network
Kodak AutoRad NT
Crossed
Network Cable
AutoRad Setup:
n insert into file C:\WINNT\system32\drivers\etc\hosts:
n IPaddress of MIM200 Computer Name of MIM200 e.g., mim
n click Report Tool button
n into menu Print film/Select Printer/New set:
n Name=DV8200, Description=DV8200, AE=8200
n Host=Computer Name of MIM200 e.g., mim, Port=5040
n Timeout=120, BitDepth=12
n Select Formats=click all formats
n Select Formats=click all formats
n Set: 1x1=4096,5195, 1x2=4096,2594; 2x2=2048,2594, 2x3=2048,1727
n Set: 3x3=1365,1727, 3x4=1365,1294; 3x5=1365,1034, 4x4=1024, 1294
n Set: 4x5=1024,1034
n Click OK to return
n Click Image Quality Calibration/Print Test Pattern to calibrate the printer
n Measure densities and enter averaged values in Calibration table
n Click OK to return and print a film to verify Calibration is done correctly
n Note: Calibration must be redone at every printer service or TFT change
MIM200 Setup:
n on Configure, Network:
n Node Name=mim, IPAddr=accordingly
n Subnet Mask=accordingly, Gateway Addr=accordingly
n on Configure, Input, Network, Add:
n Protocol=DICOM 3.0, Log.Name=DICOM, Type/Com=Keypad/COM9
n on Configure, Destination, Add, Print, Direct, Qualified, 8200, Set:
n General: Log.Name=8200, IPAddr=100.100.100.40,
n General: Database Name=8200, Model=8200, Memory=32
DICOM Network
Kodak AutoRad NT
AutoRad Setup:
n insert into file C:\WINNT\system32\drivers\etc\hosts:
n IPaddress of 8900 Computer Name of 8900 eg DV8900
n click Report Tool button
n into menu Print film/Select Printer/New set:
n Name=DV8900, Description=DV8900, AE=8900
n Host=Computer Name of 8900 eg DV8900, Port=5040
n Timeout=120, BitDepth=12
n Select Formats=click all formats
n Select Formats=click all formats
n Set: 1x1=4096,5195, 1x2=4096,2594; 2x2=2048,2594, 2x3=2048,1727
n Set: 3x3=1365,1727, 3x4=1365,1294; 3x5=1365,1034, 4x4=1024, 1294
n Set: 4x5=1024,1034
n Click OK to return
n Click Image Quality Calibration/Print Test Pattern to calibrate the printer
n Measure densities and enter averaged values in Calibration table
n Click OK to return and print a film to verify Calibration is done correctly
n Note: Calibration must be redone at every printer service or TFT change
8900 Setup:
n on Configuration, System, Network:
n Host Name=DV8900, IPAddr=accordingly
n Subnet Mask=accordingly, Gateway Addr=accordingly
n on Configuration, DICOM SCP, Communications:
n Port=5040, Association Limit=12, Source Name=DICOM
n on Configuration, Destination:
n General: Log.Name=8900
n Media Types: Media=35x43cm, 9100x11037, 10781, Any
n Media Types: Media=35x35cm,9100x9087, 8831, Any
n Media Types: Media=11x14in, 7137x9100, 8844, Any
DICOM Network
Kodak AutoRad NT
AutoRad Setup:
n insert into file C:\WINNT\system32\drivers\etc\hosts:
n IPaddress of 8150 Computer Name of 8150 eg DV8150DRE
n click Report Tool button
n into menu Print film/Select Printer/New set:
n Name=DV8150, Description=DV8150, AE=DV8150
n Host=Computer Name of 8150 eg DV8150DRE, Port=5040
n Timeout=120, BitDepth=12
n Select Formats=click all formats
n Select Formats=click all formats
n Set: 1x1=4096,5195, 1x2=4096,2594; 2x2=2048,2594, 2x3=2048,1727
n Set: 3x3=1365,1727, 3x4=1365,1294; 3x5=1365,1034, 4x4=1024, 1294
n Set: 4x5=1024,1034
n Click OK to return
n Click Image Quality Calibration/Print Test Pattern to calibrate the printer
n Measure densities and enter averaged values in Calibration table
n Click OK to return and print a film to verify Calibration is done correctly
n Note: Calibration must be redone at every printer service or TFT change
8150 Setup:
n on Configuration, System, Network:
n Host Name=DV8150DRE, IPAddr=accordingly
n Subnet Mask=accordingly, Gateway Addr=accordingly
n on Configuration, DICOM SCP, Communications:
n Port=5040, Association Limit=12, Source Name=DICOM
n on Configuration, Destination:
n AE Title: Log.Name=DV8150
n Media Types: Media=35x43cm, 4438x5390, 5262, Any
n Media Types: Media=35x35cm, 4438x4414,4286, Any
DICOM Network
Kodak AutoRad NT
AutoRad Setup:
n insert into file C:\WINNT\system32\drivers\etc\hosts:
n IPaddress of CMI1000 Computer Name of CMI1000 eg CMI1000
n click Report Tool button
n into menu Print film/Select Printer/New set:
n Name=CMI1000, Description=CMI1000, AE=CMI1000
n Host=Computer Name of CMI1000 eg CMI1000, Port=5040
n Timeout=120, BitDepth=8
n Select Formats=click only formats
n 1x1=2508,2954, 1x2=2508,1477; 2x2=1254,1477, 2x3=1254,984
n Click OK to return
n Click Image Quality Calibration/Print Test Pattern to calibrate the printer
n Measure densities and enter averaged values in Calibration table
n Click OK to return and print a film to verify Calibration is done correctly
n Note: Calibration must be redone at every printer service or TFT change
CMI-1000 Setup:
at Local Panel, under Media, set A4 or Letter ie what inside Paper Tray
(CMI-1000 sw considers only this field and uses it as A4 or Letter (Always=Y):
at Local Panel, under Menu, Imager Setup:
n Network Setup:
n IPAddr=accordingly, Subnet Mask=accordingly, Gateway=accordingly
n under More Settings: DICOM Port=5040
n Edit Host Name/AE Title=CMI1000
n Modality (SCU) Config (or after modality recognition):
n Select Modality=accordingly, Modality Config.Assistant=Yes, Reset Config=No
n Note: Color IQ settings used when images sent with Color DICOM SOP
n under Image Quality, Color Image Quality: (no need to adjust, leave defaults)
n Match Monitor Colors=default ie sRGB Color Space Profile.icm
n Adjust Color Tones=default ie Default_Contrast_100.icm
n Note: Grayscale IQ settings used when images sent with Grayscale DICOM SOP:
1
Setup valid also for Kodak PACS LINK 25 PRINT SERVER.
DICOM Network
Kodak
MasterPage Workstation
Note: Mod.Group and Contrast into Kodak camera have to be configured differently
if images that have to be printed from MasterPage are either
a) Kodak CR images or b) CT/MR images
- a) Kodak CR images are already lutted by Kodak CR, not lutted by MasterPage,
Linear-in-Density LUT into Camera ie C=1, Modality Group=4
- b) CT/MR images are not lutted by CT/MR, not lutted by MasterPage,
lutted by Camera ie C=10, Modality Group=0
8300 Setup:
n on 8300 Operator Menu into Configure User set:
n Density=16, Contrast= a) 1 or b) 10, Sharp/Smooth=1
n on 8300 Service Menu into Configure User set: Modality Group= a) 4 or b) 0
DICOM Network
Note: the Curve Shape into Kodak camera have to be configured differently
if images that have to be printed from MasterPage are either
a) Kodak CR images or b) CT/MR images
- a) Kodak CR images are already lutted by Kodak CR, not lutted by MasterPage,
Linear-in-Density LUT into Camera ie Curve Shape=0.0, Film Contrast=0
- b) CT/MR images are not lutted by CT/MR, not lutted by MasterPage,
lutted by Camera ie Curve Shape=434 (ie 3.0), Film Contrast=0
Note: if from MasterPage both typeof images have to be printed, define on
MasterPage 2 printers with same IP and Port but different AEtitles
MasterPage Setup:
n on Communication->Directory->Add Menu:
n Name=DryView, Connection Type=DICOM, IP Address=accordingly
n DICOM: Port=5040, Called AE Title=190, Calling AE Title=MasterPage
n DICOM: Supp.Services: Store=Off, Print=On, Query/Retrieve=Off, Worklist=Off
n Options: Print: Magnif.=NONE, Available=On, Title=14x17 in.
n Options: Print: Width=4096, Height=5120, Pixel Size=80
n Make an ECHO test, just to verify that the DICOM connection is working ok
n in order to print into Patient File / Print Layout:
n a) into Print / Print Setup Menu:
n select Name=DryView, Size=14x17, Add to Format menu=On
n Black&White=On, Color=Off, Bits per pixel=12, Background Color=Black
n Zoom=100, Copies=1, Trim around Image=Off, Trim around Division=On
n b) into Image/Zoom: FitToWindow=On (for True Size, FixedZoom100%=On)
n into Image: Annotations and Measurements=On, Measurement Scale=On
n into Image: DICOM informations=On, DICOM Overlays=On
n c) into Format: 1. 14x17 on DryView=On, Show Footer=On
n d) into Layout select the appropriate icon between the predifined ones
n e) into Orientation eg Portrait=On
190 Setup:
Kodak iew
Fiber Cable 3M 87
00 DryV
MasterPage Workstation
Fiber Cable
Note: the TFT and Contrast into Kodak camera have to be configured differently
if images that have to be printed from MasterPage are either
a) Kodak CR images or b) CT/MR images
- a) Kodak CR images are already lutted by Kodak CR, not lutted by MasterPage,
Linear-in-Density LUT into Camera ie TFT= WRKSTN2A, C=2
- b) CT/MR images are not lutted by CT/MR, not lutted by MasterPage,
lutted by Camera ie TFT=VER693C0, C=6
MasterPage Setup:
n on Communication->Directory->Add Menu:
n Name=DryView, Connection Type=DICOM, IP Address=accordingly
n DICOM: Port=1024, Called AE Title=9410, Calling AE Title=MasterPage
n DICOM: Supp.Services: Store=Off, Print=On, Query/Retrieve=Off, Worklist=Off
n Options: Print: Magnif.=NONE, Available=On, Title=11x14 in.
n Options: Print: Width=3380, Height=4280, Pixel Size=78
n Make an ECHO test, just to verify that the DICOM connection is working ok
n in order to print into Patient File / Print Layout:
n a) into Print / Print Setup Menu:
n select Name=DryView, Size=11x14, Add to Format menu=On
n Black&White=On, Color=Off, Bits per pixel=12, Background Color=Black
n Zoom=100, Copies=1, Trim around Image=Off, Trim around Division=On
n b) into Image/Zoom: FitToWindow=On (for True Size, FixedZoom100%=On)
n into Image: Annotations and Measurements=On, Measurement Scale=On
n into Image: DICOM informations=On, DICOM Overlays=On
n c) into Format: 1. 11x14 on DryView=On, Show Footer=On
n d) into Layout select the appropriate icon between the predifined ones
n e) into Orientation eg Portrait=On
9410 Setup:
n on Device Setup, LOCAL PRINTERS:
n Printer=8500, Model=8500, Output=Fiber
n Command Set=Superset, Baud=19200, Data=8, Stop=1, Parity=None
n Pixel=12, Header/Line, Timeout=60, Transfer Rate=2 MHz
n Film Mismatch=Print Always, Interpolation Type=831
n Interp Num=2, Max.Density=300, Contrast=6, Border Density=0
n TFT/ULUT Emulation=On, Installed TFT/ULUT=Ver693c0.w87
n on Device Setup, SCP PRINTERS, Current Providers:
n Printer=8500, AE Title= 9410, Port= 1024, Max Associations= 5
n on Device Setup, SCP PRINTERS, Registered Users:
n SCU AETitle= accordingly, SCU IPAddr=accordingly
n SCP=8500, Copies=1, Contrast Table= a) 2 or b) 6
n TFT/ULUT= a) Wrkstn2a.w87 or b) Ver693c0.w87
n Max.Density=300, Border Density=0, Mag.Type=8, Smoothing=0
n Polarity=1, Orientation=1, Set Req.Image Size=No, Priority=Low
n Interceptor=Yes, N-Event-Print Job=No, N-Event Printer=No
n Trim=No, Attribute Warning=No
n Contrast Test Mode=No, Contrast Test Mode Density=0
Kodak iew
Fiber Cable 3M 87
00 DryV
MasterPage Workstation
Fiber Cable
Note: the TFT and Contrast into Kodak camera have to be configured differently
if images that have to be printed from MasterPage are either
a) Kodak CR images or b) CT/MR images
- a) Kodak CR images are already lutted by Kodak CR, not lutted by MasterPage,
Linear-in-Density LUT into Camera ie TFT= WRKSTN2A, C=2
- b) CT/MR images are not lutted by CT/MR, not lutted by MasterPage,
lutted by Camera ie TFT=VER693C0, C=6
MasterPage Setup:
n on Communication->Directory->Add Menu:
n Name=DryView, Connection Type=DICOM, IP Address=accordingly
n DICOM: Port=1024, Called AE Title=9410, Calling AE Title=MasterPage
n DICOM: Supp.Services: Store=Off, Print=On, Query/Retrieve=Off, Worklist=Off
n Options: Print: Magnif.=NONE, Available=On, Title=14x17 in.
n Options: Print: Width=4096, Height=5220, Pixel Size=78
n Make an ECHO test, just to verify that the DICOM connection is working ok
n in order to print into Patient File / Print Layout:
n a) into Print / Print Setup Menu:
n select Name=DryView, Size=14x17, Add to Format menu=On
n Black&White=On, Color=Off, Bits per pixel=12, Background Color=Black
n Zoom=100, Copies=1, Trim around Image=Off, Trim around Division=On
n b) into Image/Zoom: FitToWindow=On (for True Size, FixedZoom100%=On)
n into Image: Annotations and Measurements=On, Measurement Scale=On
n into Image: DICOM informations=On, DICOM Overlays=On
n c) into Format: 1. 14x17 on DryView=On, Show Footer=On
n d) into Layout select the appropriate icon between the predifined ones
n e) into Orientation eg Portrait=On
9410 Setup:
n on Device Setup, LOCAL PRINTERS:
n Printer=8700, Model=8700, Output=Fiber
n Command Set=Superset, Baud=19200, Data=8, Stop=1, Parity=None
n Pixel=12, Header/Line, Timeout=60, Transfer Rate=2 MHz
n Film Mismatch=Print Always, Interpolation Type=831
n Interp Num=2, Max.Density=300, Contrast=6, Border Density=0
n TFT/ULUT Emulation=On, Installed TFT/ULUT=Ver693c0.w87
n on Device Setup, SCP PRINTERS, Current Providers:
n Printer=8700, AE Title= 9410, Port= 1024, Max Associations= 5
n on Device Setup, SCP PRINTERS, Registered Users:
n SCU AETitle= accordingly, SCU IPAddr=accordingly
n SCP=8700, Copies=1, Contrast Table= a) 2 or b) 6
n TFT/ULUT= a) Wrkstn2a.w87 or b) Ver693c0.w87
n Max.Density=300, Border Density=0, Mag.Type=8, Smoothing=0
n Polarity=1, Orientation=1, Set Req.Image Size=No, Priority=Low
n Interceptor=Yes, N-Event-Print Job=No, N-Event Printer=No
n Trim=No, Attribute Warning=No
n Contrast Test Mode=No, Contrast Test Mode Density=0
DICOM Network
RS422
COPCIL Board 9-pole Plug
Copper Cable Control 9-pin
Kodak
MasterPage Workstation
Data 37-pin
Note: the TFT and Contrast into Kodak camera have to be configured differently
if images that have to be printed from MasterPage are either
a) Kodak CR images or b) CT/MR images
- a) Kodak CR images are already lutted by Kodak CR, not lutted by MasterPage,
Linear-in-Density LUT into Camera ie TFT= WRKSTN2A, C=2
- b) CT/MR images are not lutted by CT/MR, not lutted by MasterPage,
lutted by Camera ie TFT=VER693C0, C=6
MasterPage Setup:
n on Communication->Directory->Add Menu:
n Name=DryView, Connection Type=DICOM, IP Address=accordingly
n DICOM: Port=1024, Called AE Title=9410, Calling AE Title=MasterPage
n DICOM: Supp.Services: Store=Off, Print=On, Query/Retrieve=Off, Worklist=Off
n Options: Print: Magnif.=NONE, Available=On, Title=14x17 in.
n Options: Print: Width=4096, Height=5216, Pixel Size=78
n Make an ECHO test, just to verify that the DICOM connection is working ok
n in order to print into Patient File / Print Layout:
n a) into Print / Print Setup Menu:
n select Name=DryView, Size=14x17, Add to Format menu=On
n Black&White=On, Color=Off, Bits per pixel=12, Background Color=Black
n Zoom=100, Copies=1, Trim around Image=Off, Trim around Division=On
n b) into Image/Zoom: FitToWindow=On (for True Size, FixedZoom100%=On)
n into Image: Annotations and Measurements=On, Measurement Scale=On
n into Image: DICOM informations=On, DICOM Overlays=On
n c) into Format: 1. 14x17 on DryView=On, Show Footer=On
n d) into Layout select the appropriate icon between the predifined ones
n e) into Orientation eg Portrait=On
9410 Setup:
on Device Setup, LOCAL PRINTERS:
n Printer=8100, Model=8100 4096 pxls/line, Output=Copper
n Baud=1200, Parity=Even, Data=8, Stop=1, Command Set=952
n Pixel=12, Header/Line, Timeout=60, Transfer Rate=1 MHz
n Film Mismatch=Print Always, Interpolation Type=831
n Interp Num=2, Max.Density=300, Contrast=6, Border Density=0
n TFT/ULUT Emulation=On, Installed TFT/ULUT=Ver693c0.w87
on Device Setup, SCP PRINTERS, Current Providers:
n Printer=8100, AE Title= 9410, Port= 1024, Max Associations= 5
on Device Setup, SCP PRINTERS, Registered Users:
n SCU AETitle= accordingly, SCU IPAddr=accordingly
n SCP=8100, Copies=1, Contrast Table= a) 2 or b) 6
n TFT/ULUT= a) Wrkstn2a.w87 or b) Ver693c0.w87
n Max.Density=300, Border Density=0, Mag.Type=8, Smoothing=0
n Polarity=1, Orientation=1, Set Req.Image Size=No, Priority=Low
n Interceptor=Yes, N-Event-Print Job=No, N-Event Printer=No
n Trim=No, Attribute Warning=No
n Contrast Test Mode=No, Contrast Test Mode Density=0
DICOM Network
Control 9 pin
Kodak COPCIL board
MasterPage Workstation Copper Cable
Data 37 pin
Note: TFT/ULUT and Contrast into Kodak camera have to be configured differently
if images that have to be printed from MasterPage are either
a) Kodak CR images or b) CT/MR images
- a) Kodak CR images are already lutted by Kodak CR, not lutted by MasterPage,
Linear-in-Density LUT into Camera ie TFT/ULUT= wrkstn83a.w8u, C=1
- b) CT/MR images are not lutted by CT/MR, not lutted by MasterPage,
lutted by Camera ie TFT/ULUT= u1_109b.w8u, C=10
9410 Setup:
n on Device Setup, LOCAL PRINTERS:
n Printer=8300, Model=8300 Copper, Output=Copper
n Command Set=952, Baud=1200, Data=8, Stop=1, Parity=Even
n Pixel=8, Header/Line, Timeout=60, Transfer Rate=1 MHz
n Film Mismatch=Print Always, Interpolation Type=831
n Interp Num=0, Max.Density=300, Contrast=6, Border Density=0
n TFT/ULUT Emulation=On, Installed TFT/ULUT=upmsv3k.w8u
n on Device Setup, SCP PRINTERS, Current Providers:
n Printer=8300, AE Title= 9410, Port= 1024, Max Associations= 5
n on Device Setup, SCP PRINTERS, Registered Users:
n SCU AETitle= accordingly, SCU IPAddr=accordingly
n SCP=8300, Copies=1, Contrast Table= a) 1 or b) 10
n TFT/ULUT= a) wrkstn83a.w8u or b) u1_109b.w8u
n Max.Density=300, Border Density=0, Mag.Type=8, Smoothing=1
n Polarity=1, Orientation=1, Set Req.Image Size=No, Priority=Low
n Interceptor=Yes, N-Event-Print Job=No, N-Event Printer=No
n Trim=No, Attribute Warning=No
n Contrast Test Mode=No, Contrast Test Mode Density=0
8300 Setup:
n on Operator Menu set: D=16, C=6, Sharp/Smooth=0 ie Auto
n on Operator Menu set: Film Layout: 1 on 1=Portrait
n on Service Menu set: Ratio=1.00, Serial=1200,8,1,Even,Comma,3M, Memory=16
n on Service Menu set: Digital Interface: Parity=Even, Modality Group=1
DICOM Network
Data 37 pin
MasterPage Setup:
n on Communication->Directory->Add Menu:
n Name=DryView, Connection Type=DICOM, IP Address=accordingly
n DICOM: Port=1024, Called AE Title=9410, Calling AE Title=MasterPage
n DICOM: Supp.Services: Store=Off, Print=On, Query/Retrieve=Off, Worklist=Off
n Options: Print: Magnif.=NONE, Available=On, Title=8x10 in.
n Options: Print: Width=5024, Height=6200, Pixel Size=39
n Make an ECHO test, just to verify that the DICOM connection is working ok
n in order to print into Patient File / Print Layout:
n a) into Print / Print Setup Menu:
n select Name=DryView, Size=8x10, Add to Format menu=On
n Black&White=On, Color=Off, Bits pixel=12 (8 if 8600), Background Color=Black
n Zoom=100, Copies=1, Trim around Image=Off, Trim around Division=On
n b) into Image/Zoom: FitToWindow=On (for True Size, FixedZoom100%=On)
n into Image: Annotations and Measurements=On, Measurement Scale=On
n into Image: DICOM informations=On, DICOM Overlays=On
n c) into Format: 1. 8x10 on DryView=On, Show Footer=On
n d) into Layout select the appropriate icon between the predifined ones
n e) into Orientation eg Portrait=On
9410 Setup:
n on Device Setup, LOCAL PRINTERS:
n Printer=8610, Model=8600/8610, Output=Copper
n Command Set=952, Baud=1200, Data=8, Stop=1, Parity=Even
n Pixel=12 (8 if 8600), Header/Line, Timeout=60, Transfer Rate=2 MHz
n Film Mismatch=Print Always, Interpolation Type=831
n Interp Num=1, Installed TFT/ULUT= don’t care
n Max.Density=300, Contrast=5, Border Density=0
n on Device Setup, SCP PRINTERS, Current Providers:
n Printer=8610, AE Title= 9410, Port= 1024, Max Associations= 5
n on Device Setup, SCP PRINTERS, Registered Users:
n SCU AETitle= accordingly, SCU IPAddr=accordingly
n SCP=8610, Copies=1, Contrast Table= a) 6 or b) 3, Max.Density=350
n Border Density=0, Mag.Type=8, Smoothing=1
n Polarity=1, Orientation=1, Set Req.Image Size=No, Priority=Low
n Gamma= a) Linear in Density or b) Linear in Transmittance
n Contrast Group= a) 1 or b) 6, Kernel Group=1
n Interceptor=Yes, N-Event-Print Job=No, N-Event Printer=No
n Trim=No, Attribute Warning=No
n Contrast Test Mode=No, Contrast Test Mode Density=0
8610 Setup: on 8610 Operator Menu into Test Menu, Software Version, verify:
n Imager=2.4, VRTX32=1.08, Contrast=6.P.2, Conv.Kernel=M.1.0
n (if 8600: Imager=2.5, Contrast=6.G.7, Conv.Kernel=1.0.5)
n on 8610 Operator Menu into Configure User set:
n Density=16, Contrast=6, Sharp/Smooth=1, Film Layout: 1:1P
n Gamma=Xmittance, Image Size=Scale To Fit, Detector Size=don’t care
n on 8610 Service Menu into Configure User set:
n Ratio=1.00, Serial Control Intf.=1200,8,1,Even,Comma,3M, Memory=255
n Digital Interface: Parity=Even, Modality Group=1, Smoothing Group=1
DICOM Network
3 M H Q L aser Im ag er
Kodak
Fiber Cable
MasterPage Workstation
Fiber Cable
Note: the TFT and Contrast into Kodak camera have to be configured differently
if images that have to be printed from MasterPage are either
a) Kodak CR images or b) CT/MR images
- a) Kodak CR images are already lutted by Kodak CR, not lutted by MasterPage,
Linear-in-Density LUT into Camera ie TFT= WRKSTN2A, C=2
- b) CT/MR images are not lutted by CT/MR, not lutted by MasterPage,
lutted by Camera ie TFT=VER693C0, C=6
MasterPage Setup:
n on Communication->Directory->Add Menu:
n Name=DryView, Connection Type=DICOM, IP Address=accordingly
n DICOM: Port=1024, Called AE Title=9410, Calling AE Title=MasterPage
n DICOM: Supp.Services: Store=Off, Print=On, Query/Retrieve=Off, Worklist=Off
n Options: Print: Magnif.=NONE, Available=On, Title=14x17 in.
n Options: Print: Width=4096, Height=4992, Pixel Size=82
n Make an ECHO test, just to verify that the DICOM connection is working ok
n in order to print into Patient File / Print Layout:
n a) into Print / Print Setup Menu:
n select Name=DryView, Size=14x17, Add to Format menu=On
n Black&White=On, Color=Off, Bits per pixel=12, Background Color=Black
n Zoom=100, Copies=1, Trim around Image=Off, Trim around Division=On
n b) into Image/Zoom: FitToWindow=On (for True Size, FixedZoom100%=On)
n into Image: Annotations and Measurements=On, Measurement Scale=On
n into Image: DICOM informations=On, DICOM Overlays=On
n c) into Format: 1. 14x17 on DryView=On, Show Footer=On
n d) into Layout select the appropriate icon between the predifined ones
n e) into Orientation eg Portrait=On
9410 Setup:
n on Device Setup, LOCAL PRINTERS:
n Printer=969, Model=969, Output=Fiber
n Command Set=Superset, Baud=19200, Data=8, Stop=1, Parity=None
n Pixel=12, Header/Line, Timeout=60, Transfer Rate=2 MHz
n Film Mismatch=Print Always, Interpolation Type=831
n Interp Num=2, Max.Density=300, Contrast=6, Border Density=0
n TFT/ULUT Emulation=On, Installed TFT/ULUT=Ver693c0.w87
n on Device Setup, SCP PRINTERS, Current Providers:
n Printer=969, AE Title= 9410, Port= 1024, Max Associations= 5
n on Device Setup, SCP PRINTERS, Registered Users:
n SCU AETitle= accordingly, SCU IPAddr=accordingly
n SCP=969, Copies=1, Contrast Table= a) 2 or b) 6
n TFT/ULUT= a) Wrkstn2a.w87 or b) Ver693c0.w87
n Max.Density=300, Border Density=0, Mag.Type=8, Smoothing=0
n Polarity=1, Orientation=1, Set Req.Image Size=No, Priority=Low
n Interceptor=Yes, N-Event-Print Job=No, N-Event Printer=No
n Trim=No, Attribute Warning=No
n Contrast Test Mode=No, Contrast Test Mode Density=0
969 Setup:
n on COMM Menu: 969 Default
n on IMAGE Menu: TFT=VER693C0, Dmax=3.00, Contrast=6, Density=14
n on EIB Menu: Pixel=12, Header/Line, Port=0, Parity=Enable Even, Timeout=60
DICOM Network
Kodak
MasterPage Workstation Kodak 160 camera
Crossed
Network Cable
Note: the Curve Shape into Kodak camera have to be configured differently
if images that have to be printed from MasterPage are either
a) Kodak CR images or b) CT/MR images
- a) Kodak CR images are already lutted by Kodak CR, not lutted by MasterPage,
Linear-in-Density LUT into Camera ie Curve Shape=0.0, Film Contrast=0
- b) CT/MR images are not lutted by CT/MR, not lutted by MasterPage,
lutted by Camera ie Curve Shape=434 (ie 3.0), Film Contrast=0
Note: if from MasterPage both typeof images have to be printed, define on
MasterPage 2 printers with same IP and Port but different AEtitles
MasterPage Setup:
n on Communication->Directory->Add Menu:
n Name=DryView, Connection Type=DICOM, IP Address=accordingly
n DICOM: Port=5040, Called AE Title=160, Calling AE Title=MasterPage
n DICOM: Supp.Services: Store=Off, Print=On, Query/Retrieve=Off, Worklist=Off
n Options: Print: Magnif.=NONE, Available=On, Title=14x17 in.
n Options: Print: Width=4360, Height=5348, Pixel Size=78
n Make an ECHO test, just to verify that the DICOM connection is working ok
n in order to print into Patient File / Print Layout:
n a) into Print / Print Setup Menu:
n select Name=DryView, Size=14x17, Add to Format menu=On
n Black&White=On, Color=Off, Bits per pixel=12, Background Color=Black
n Zoom=100, Copies=1, Trim around Image=Off, Trim around Division=On
n b) into Image/Zoom: FitToWindow=On (for True Size, FixedZoom100%=On)
n into Image: Annotations and Measurements=On, Measurement Scale=On
n into Image: DICOM informations=On, DICOM Overlays=On
n c) into Format: 1. 14x17 on DryView=On, Show Footer=On
n d) into Layout select the appropriate icon between the predifined ones
n e) into Orientation eg Portrait=On
MIM200 Setup:
n on Configure, Network:
n Computer Name=eg Kodak160, IPAddr=accordingly
n Subnet Mask=accordingly, Gateway Addr=accordingly
n on Configure, Input, Network, Add:
n Protocol=DICOM 3.0, Log.Name=DICOM, Type/Com=Keypad/COM9
n on Configure, Destination, Add, Print, Direct, Qualified, KELI 160, Set:
n General: Log.Name=KELI 160, IPAddr=100.100.100.30,
n General: Database Name=KELI 160, Model=KELI 160
n Media Info: Media=35x43cm, 4361x5348, 5228, Any (Blue,Clear)
n Supported Item: Collation=On, Text=On, Tonescaling on Image=On
n Supported Item: Pivot Density=On, Rotation=On
n Interpolation: NoMag=On, Bil=On, Repl=On,Cubic=On, Cubic 2=On
n Format Types: Custom=On, Slide=On, Row Symmetric=On
n Format Types: 1, 2, 4, 6, 8, 9, 12, 15, 16, 20, 24, 30, 35=On
n Formatting: Aspect Ratio Mix Page=On, Image Size Mix in Std Fmt=On
n Formatting: DICOM Annotation Box=On, Req.Size Scale=On
n Formatting: Req.Size Mix in Row=On, Trim=On
n Formatting: Aspect Ratio Mix in Row=On, Image Size Mix in Row=On
n Formatting: Req.Image Size=On, Req.Size Mix on Page=On
n Formatting: True Landscape=On
n Formatting: Max Img Band=20, Max Band per Page=20, Max Img Col=0
n Formatting: Max Img Row=0, Min Horiz Sep=2, Min Vert Sep=2
n Formatting: Trim Width Enabled=2, Trim Width Disabled=0
n Formatting: Pixel Pitch=12.8
n Image Processing: Grayscale=On, Minify/Crop=On, Max Image Dmax=3.2
n M952 Usage: Min H/V Mag=0, Max H/V Mag=0, Min Dmax 952=1.7
n on Configure, SCP Services, select the specific modality, Modify:
n PLUT=N, ToneScaling=Curve Shape (Always=Y)
n Curve Shape= a) 0 or b) 3 ie 435 (Always=N)
n Contrast (wet)=0 (Always=N)
n Image Dmin=0.00 (Always=N), Image Dmax=3.00 (Always=N)
n NeventReports=Off (Always=Y), Warning Status=On
n Print Date=Off, Print Time=Off, Page Number=Off, Hosp.Name=Off
n Modality ID=Off, Annotation Override=Off (Always=N)
n Minify/Scale=On, Crop=Off, Text Box Relocation=None (Always=N)
n Print Priority=Normal (Always=N), Image Polarity=Normal (Always=N)
n Interpolation= Cubic, Border=3.99 (Always=N)
n Film Base=Blue Film (Always=N), Film Size=14INx17IN (Always=N)
n Negotiate Color Print=Off
Kodak
Kodak 2180 camera
MasterPage Workstation
Fiber Cable
Note: the Curve Shape into Kodak camera have to be configured differently
if images that have to be printed from MasterPage are either
a) Kodak CR images or b) CT/MR images
- a) Kodak CR images are already lutted by Kodak CR, not lutted by MasterPage,
Linear-in-Density LUT into Camera ie Curve Shape=0.0, Film Contrast=0
- b) CT/MR images are not lutted by CT/MR, not lutted by MasterPage,
lutted by Camera ie Curve Shape=434 (ie 3.0), Film Contrast=0
Note: if from MasterPage both typeof images have to be printed, define on
MasterPage 2 printers with same IP and Port but different AEtitles
MasterPage Setup:
n on Communication->Directory->Add Menu:
n Name=DryView, Connection Type=DICOM, IP Address=accordingly
n DICOM: Port=5040, Called AE Title=2180, Calling AE Title=MasterPage
n DICOM: Supp.Services: Store=Off, Print=On, Query/Retrieve=Off, Worklist=Off
n Options: Print: Magnif.=NONE, Available=On, Title=14x17 in.
n Options: Print: Width=4096, Height=5156, Pixel Size=79
n Make an ECHO test, just to verify that the DICOM connection is working ok
n in order to print into Patient File / Print Layout:
n a) into Print / Print Setup Menu:
n select Name=DryView, Size=14x17, Add to Format menu=On
n Black&White=On, Color=Off, Bits per pixel=12, Background Color=Black
n Zoom=100, Copies=1, Trim around Image=Off, Trim around Division=On
n b) into Image/Zoom: FitToWindow=On (for True Size, FixedZoom100%=On)
n into Image: Annotations and Measurements=On, Measurement Scale=On
n into Image: DICOM informations=On, DICOM Overlays=On
n c) into Format: 1. 14x17 on DryView=On, Show Footer=On
n d) into Layout select the appropriate icon between the predifined ones
n e) into Orientation eg Portrait=On
MIM200 Setup:
n on Configure, Network:
n Computer Name=eg Kodak2180, IPAddr=accordingly
n Subnet Mask=accordingly, Gateway Addr=accordingly
n on Configure, Input, Network, Add:
n Protocol=DICOM 3.0, Log.Name=DICOM, Type/Com=Keypad/COM9
n on Configure, Destination, Add, Print, Direct, Qualified, KELP 2180, Set:
n General: Log.Name=KELP2180, Database Name=KELP 2180
n General: Model=KELP 2180, Memory=24, Node ID=6 or accordingly
n Media Info: Media=35x43cm, 4136x5160, 5030, (Blue)
n Media Info:Media=35x35cm,4136x4136,4006, (Blue)
n Media Info: Media=11x14in, 3240x4136, 4006, (Blue)
n Media Info: Media=8x10in, 2290x2840, 2710, (Blue)
n Supported Item: Collation=On, Text=On, Tonescaling=On, Rotation=On
n Interpolation: NoMag=On, Bil=On, Repl=On,Cubic=On, Cubic 2=On
n Format Types: Custom=On, Slide=On, Row Symmetric=On
n Format Types: 1, 2, 4, 6, 8, 9, 12, 15, 16, 20, 24, 30, 35=On
n Formatting: Aspect Ratio Mix Page=On, Image Size Mix in Std Fmt=On
n Formatting: DICOM Annotation Box=On, Req.Size Scale=On
n Formatting: Req.Size Mix in Row=On, Trim=On
n Formatting: Aspect Ratio Mix in Row=On, Image Size Mix in Row=On
n Formatting: Req.Image Size=On, Req.Size Mix on Page=On
n Formatting: True Landscape=On
n Formatting: Max Img Band=20, Max Band per Page=20, Max Img Col=0
n Formatting: Max Img Row=0, Min Horiz Sep=2, Min Vert Sep=2
n Formatting: Trim Width Enabled=2, Trim Width Disabled=2
n Formatting: Pixel Pitch=12.6582
n Image Processing: Grayscale=On, Minify=On, Max Image Dmax=3.2
n M952 Usage: Min H/V Mag=0, Max H/V Mag=0, Min Dmax 952=1.7
n on Configure, SCP Services, select the specific modality, Modify:
n PLUT=N, ToneScaling=Curve Shape (Always=Y)
n Curve Shape=a) 0 or b) 3 ie 435 (Always=N), Contrast (wet)=0 (Always=N)
n Image Dmin=0.00 (Always=N), Image Dmax=3.00 (Always=N)
n NeventReports=Off (Always=Y), Warning Status=On
n Print Date=Off, Print Time=Off, Page Number=Off, Hosp.Name=Off
n Modality ID=Off, Annotation Override=Off (Always=N)
n Minify/Scale=On, Crop=Off, Text Box Relocation=None
n Print Priority=Normal (Always=N), Image Polarity=Normal (Always=N)
n Interpolation= Cubic, Border=3.99 (Always=N)
n Film Base=Blue Film (Always=N), Film Size=14INx17IN (Always=N)
n Negotiate Color Print=Off
2180 Setup:
n Optical Interface board will automatic configure into 2180, no setup needed
Kodak
Kodak 1120 camera
MasterPage Workstation
Fiber Cable
Note: the Curve Shape into Kodak camera have to be configured differently
if images that have to be printed from MasterPage are either
a) Kodak CR images or b) CT/MR images
- a) Kodak CR images are already lutted by Kodak CR, not lutted by MasterPage,
Linear-in-Density LUT into Camera ie Curve Shape=0.0, Film Contrast=0
- b) CT/MR images are not lutted by CT/MR, not lutted by MasterPage,
lutted by Camera ie Curve Shape=434 (ie 3.0), Film Contrast=0
Note: if from MasterPage both typeof images have to be printed, define on
MasterPage 2 printers with same IP and Port but different AEtitles
MasterPage Setup:
n on Communication->Directory->Add Menu:
n Name=DryView, Connection Type=DICOM, IP Address=accordingly
n DICOM: Port=5040, Called AE Title=1120, Calling AE Title=MasterPage
n DICOM: Supp.Services: Store=Off, Print=On, Query/Retrieve=Off, Worklist=Off
n Options: Print: Magnif.=NONE, Available=On, Title=14x17 in.
n Options: Print: Width=4096, Height=5132, Pixel Size=80
n Make an ECHO test, just to verify that the DICOM connection is working ok
n in order to print into Patient File / Print Layout:
n a) into Print / Print Setup Menu:
n select Name=DryView, Size=14x17, Add to Format menu=On
n Black&White=On, Color=Off, Bits per pixel=12, Background Color=Black
n Zoom=100, Copies=1, Trim around Image=Off, Trim around Division=On
n b) into Image/Zoom: FitToWindow=On (for True Size, FixedZoom100%=On)
n into Image: Annotations and Measurements=On, Measurement Scale=On
n into Image: DICOM informations=On, DICOM Overlays=On
n c) into Format: 1. 14x17 on DryView=On, Show Footer=On
n d) into Layout select the appropriate icon between the predifined ones
n e) into Orientation eg Portrait=On
MIM200 Setup:
n on Configure, Network:
n Computer Name=eg Kodak1120, IPAddr=accordingly
n Subnet Mask=accordingly, Gateway Addr=accordingly
n on Configure, Input, Network, Add:
n Protocol=DICOM 3.0, Log.Name=DICOM, Type/Com=Keypad/COM9
n on Configure, Destination, Add, Print, Direct, Qualified, KELP 1120, Set:
n General: Log.Name=KELP1120, Database Name=KELP 1120
n General: Model=KELP 1120, Memory=20, Node ID=6 or accordingly
n Media Info: Media=35x43cm, 4096x5132, 5034, (Blue)
n Media Info: Media=35x35cm, 4096x4108, 4010, (Blue)
n Media Info: Media=11x14in, 4096x3232, 3134, (Blue)
n Media Info: Media=8x10in, 2304x2900, 2802, (Blue)
n Supported Item: Collation=On, Text=On, Tonescaling=On, Rotation=On
n Interpolation: NoMag=On, Repl=On,Cubic Spline=On
n Format Types: Custom=On, Slide=On, Row Symmetric=On
n Format Types: 1, 2, 4, 6, 8, 9, 12, 15, 16, 20, 24, 30, 35=On
n Formatting: Aspect Ratio Mix Page=On, Image Size Mix in Std Fmt=On
n Formatting: DICOM Annotation Box=On, Req.Size Scale=On
n Formatting: Req.Size Mix in Row=On
n Formatting: Aspect Ratio Mix in Row=On, Image Size Mix in Row=On
n Formatting: Req.Image Size=On, Req.Size Mix on Page=On
n Formatting: True Landscape=On
n Formatting: Max Img Band=20, Max Band per Page=20, Max Img Col=0
n Formatting: Max Img Row=0, Min Horiz Sep=3, Min Vert Sep=0
n Formatting: Trim Width Enabled=0, Trim Width Disabled=0
n Formatting: Pixel Pitch=12.5
n Image Processing: Grayscale=On, Minify=On, Max Image Dmax=2.8
n M952 Usage: Min H/V Mag=0, Max H/V Mag=0, Min Dmax 952=1.7
n on Configure, SCP Services, select the specific modality, Modify:
n PLUT=N, ToneScaling=Curve Shape (Always=Y)
n Curve Shape=a) 0 or b) 3 ie 435 (Always=N), Contrast (wet)=0 (Always=N)
n Image Dmin=0.00 (Always=N), Image Dmax=3.00 (Always=N)
n NeventReports=Off (Always=Y), Warning Status=On
n Print Date=Off, Print Time=Off, Page Number=Off, Hosp.Name=Off
n Modality ID=Off, Annotation Override=Off (Always=N)
n Minify/Scale=On, Crop=Off, Text Box Relocation=None
n Print Priority=Normal (Always=N), Image Polarity=Normal (Always=N)
n Interpolation= Cubic, Border=3.99 (Always=N)
n Film Base=Blue Film (Always=N), Film Size=14INx17IN (Always=N)
n Negotiate Color Print=Off
1120 Setup:
n Optical Interface board will automatic configure into 1120, no setup needed
DICOM Network
Kodak
MasterPage Workstation
Crossed
Network Cable
Note: the TFT and Contrast into Kodak camera have to be configured differently
if images that have to be printed from MasterPage are either
a) Kodak CR images or b) CT/MR images
- a) Kodak CR images are already lutted by Kodak CR, not lutted by MasterPage,
Linear-in-Density LUT into Camera ie TFT= WRKSTN2A, C=2
- b) CT/MR images are not lutted by CT/MR, not lutted by MasterPage,
lutted by Camera ie TFT=VER693C0, C=6
Note: if from MasterPage both typeof images have to be printed, define on
MasterPage 2 printers with same IP and Port but different AEtitles
MasterPage Setup:
n on Communication->Directory->Add Menu:
n Name=DryView, Connection Type=DICOM, IP Address=accordingly
n DICOM: Port=5040, Called AE Title=8200, Calling AE Title=MasterPage
n DICOM: Supp.Services: Store=Off, Print=On, Query/Retrieve=Off, Worklist=Off
n Options: Print: Magnif.=NONE, Available=On, Title=14x17 in.
n Options: Print: Width=4360, Height=5220, Pixel Size=78
n Make an ECHO test, just to verify that the DICOM connection is working ok
n in order to print into Patient File / Print Layout:
n a) into Print / Print Setup Menu:
n select Name=DryView, Size=14x17, Add to Format menu=On
n Black&White=On, Color=Off, Bits per pixel=12, Background Color=Black
n Zoom=100, Copies=1, Trim around Image=Off, Trim around Division=On
n b) into Image/Zoom: FitToWindow=On (for True Size, FixedZoom100%=On)
n into Image: Annotations and Measurements=On, Measurement Scale=On
n into Image: DICOM informations=On, DICOM Overlays=On
n c) into Format: 1. 14x17 on DryView=On, Show Footer=On
n d) into Layout select the appropriate icon between the predifined ones
n e) into Orientation eg Portrait=On
MIM200 Setup:
n on Configure, Network:
n Node Name=MIM, IPAddr=accordingly
n Subnet Mask=accordingly, Gateway Addr=accordingly
n on Configure, Input, Network, Add:
n Protocol=DICOM 3.0, Log.Name=DICOM, Type/Com=Keypad/COM9
n on Configure, Destination, Add, Print, Direct, Qualified, 8200, Set:
n General: Log.Name=8200, IPAddr=100.100.100.40,
n General: Database Name=8200, Model=8200, Memory=32
n Media Info: Media=35x43cm, 4361x5223, 5133, Blue
n Media Info: Media=35x35cm, 4361x4247, 4157, Blue
n Media Info: Media=11x14in, 3272x4361, 4271, Blue
n Supported Item: Collation=On, Common Text=On, Tonescaling=On
n Supported Item: Remote Image Deletion=On, Rotation=On
n Interpolation: No Magnification=On, Bilin=On, Repl=On
n Interpolation: Cubic Spline=On, Cubic Convolution 2=On
n Format Types: Custom=On, Row Symmetric=On
n Format Types: 1, 2, 4, 6, 8, 9, 12, 15, 16, 20, 24, 30, 35=On
n Formatting: Aspect Ratio Mix on Page=On
n Formatting: Image Size Mix in Std Fmt=On
n Formatting: DICOM Annotation Box=On, Req.Size Scale=On
n Formatting: Req.Size Mix in Row=On, Trim=On
n Formatting: Aspect Ratio Mix in Row=On, Image Size Mix in Row=On
n Formatting: Req.Image Size=On, Req.Size Mix on Page=On
n Formatting: True Landscape=On
n Formatting: Max Img per Band=20, Max Band per Page=20
n Formatting: Max Img Col=0, Max Img Row=0,
n Formatting: Min Horiz Sep=2, Min Vert Sep=2
n Formatting: Trim Width Enabled=2, Trim Width Disabled=0
n Formatting: Pixel Pitch=12.8205
n Image Processing: Grayscale=On, Minify/Crop=On, Max Image Dmax=3.1
n SCU: Density Space= On, PLUT Service= On
n SCU: Curve Shape Tonescaling=On, Perception LUT Tonescaling=On
n M952 Usage: Min H/V Mag=1, Max H/V Mag=64, Min Dmax 952=1.7
n at Keypad connected to MIM, press Menu, Service Menu, SCP Services:
n PLUT=N, ToneScaling=PerceptionLUT (Always=Y)
n TFT/ULUT= a) Wrkstn2a.w87 or b) Ver693c0.w87 (Always=N)
n Contrast (dry)= a) 2 or b) 6 (Always=N)
n Image Dmin=0.00 (Always=N), Image Dmax=3.00 (Always=N)
n Smoothing Type=0 (Always=N), Image Polarity=Normal (Always=N)
n NeventReports=Off (Always=Y), Warning Status=On
n Print Date=Off, Print Time=Off, Page Number=Off, Hosp.Name=Off
n Modality ID=Off, Annotation Override=Off (Always=N)
n Minify/Scale=On, Crop=Off, Text Box Relocation=None
n Print Priority=Normal (Always=N), Border=3.99 (Always=N)
n Film Base=Blue Film (Always=N), Film Size=14INx17IN (Always=N)
Kodak iew
Fiber Cable 3M 87
00 DryV
MasterPage Workstation
Fiber Cable
Note: the TFT and Contrast into Kodak camera have to be configured differently
if images that have to be printed from MasterPage are either
a) Kodak CR images or b) CT/MR images
- a) Kodak CR images are already lutted by Kodak CR, not lutted by MasterPage,
Linear-in-Density LUT into Camera ie TFT= WRKSTN2A, C=2
- b) CT/MR images are not lutted by CT/MR, not lutted by MasterPage,
lutted by Camera ie TFT=VER693C0, C=6
Note: if from MasterPage both typeof images have to be printed, define on
MasterPage 2 printers with same IP and Port but different AEtitles
MasterPage Setup:
n on Communication->Directory->Add Menu:
n Name=DryView, Connection Type=DICOM, IP Address=accordingly
n DICOM: Port=5040, Called AE Title=8500, Calling AE Title=MasterPage
n DICOM: Supp.Services: Store=Off, Print=On, Query/Retrieve=Off, Worklist=Off
n Options: Print: Magnif.=NONE, Available=On, Title=11x14 in.
n Options: Print: Width=3380, Height=4280, Pixel Size=78
n Make an ECHO test, just to verify that the DICOM connection is working ok
n in order to print into Patient File / Print Layout:
n a) into Print / Print Setup Menu:
n select Name=DryView, Size=11x14, Add to Format menu=On
n Black&White=On, Color=Off, Bits per pixel=12, Background Color=Black
n Zoom=100, Copies=1, Trim around Image=Off, Trim around Division=On
n b) into Image/Zoom: FitToWindow=On (for True Size, FixedZoom100%=On)
n into Image: Annotations and Measurements=On, Measurement Scale=On
n into Image: DICOM informations=On, DICOM Overlays=On
n c) into Format: 1. 11x14 on DryView=On, Show Footer=On
n d) into Layout select the appropriate icon between the predifined ones
n e) into Orientation eg Portrait=On
MIM200 Setup:
n on Configure, Network:
n Node Name=MIM, IPAddr=accordingly
n Subnet Mask=accordingly, Gateway Addr=accordingly
n on Configure, Input, Network, Add:
n Protocol=DICOM 3.0, Log.Name=DICOM, Type/Com=Keypad/COM9
n on Configure, Destination, Add, Print, Direct, Qualified, 8500, Set:
n General: Log.Name=8500
n General: Database Name=8500, Model=8500, Memory=32
n Media Info: Media=11x14in, 3388x4283, 4193, Blue
n Output Params: Cmd=SuperSet,Baud=19200,Data=8,Stop=1,Parity=None
n Output Params: Pixel=12, Header/Line, Transfer=2000 KHz, Acq=60
n Supported Item: Collation=On, Text=On, Tonescaling=On, Rotation=On
n Interpolation: NoMag=On, Bilin=On, Repl=On,Cubic Spline=On
n Format Types: Custom=On, Slide=On, Row Symmetric=On
n Format Types: 1, 2, 4, 6, 8, 9, 12, 15, 16, 20, 24, 30, 35=On
n Formatting: Aspect Ratio Mix Page=On, Image Size Mix in Std Fmt=On
n Formatting: DICOM Annotation Box=On, Req.Size Scale=On
n Formatting: Req.Size Mix in Row=On, Trim=On
n Formatting: Aspect Ratio Mix in Row=On, Image Size Mix in Row=On
n Formatting: Req.Image Size=On, Req.Size Mix on Page=On
n Formatting: True Landscape=On
n Formatting: Max Img Band=20, Max Band per Page=20, Max Img Col=0
n Formatting: Max Img Row=0, Min Horiz Sep=2, Min Vert Sep=2
n Formatting: Trim Width Enabled=2, Trim Width Disabled=0
n Formatting: Pixel Pitch=12.8205
n Image Processing: Grayscale=On, Minify=On, Max Image Dmax=3.1
n M952 Usage: Min H/V Mag=1, Max H/V Mag=64, Min Dmax 952=1.7
n on Configure, SCP Services, select the specific modality, Modify:
n PLUT=N, ToneScaling=PerceptionLUT (Always=Y)
n TFT/ULUT= a) Wrkstn2a.w87 or b) Ver693c0.w87 (Always=N)
n Contrast (dry)= a) 2 or b) 6 (Always=N)
n Image Dmin=0.00 (Always=N), Image Dmax=3.00 (Always=N)
n Smoothing Type=0 (Always=N), Image Polarity=Normal (Always=N)
n NeventReports=Off (Always=Y), Warning Status=On
n Print Date=Off, Print Time=Off, Page Number=Off, Hosp.Name=Off
n Modality ID=Off, Annotation Override=Off (Always=N)
n Minify/Scale=On, Crop=Off, Text Box Relocation=None
n Print Priority=Normal (Always=N), Border=3.99 (Always=N)
n Film Base=Blue Film (Always=N), Film Size=11INx14IN (Always=N)
n Negotiate Color Print=Off
Kodak iew
Fiber Cable 3M 87
00 DryV
MasterPage Workstation
Fiber Cable
Note: the TFT and Contrast into Kodak camera have to be configured differently
if images that have to be printed from MasterPage are either
a) Kodak CR images or b) CT/MR images
- a) Kodak CR images are already lutted by Kodak CR, not lutted by MasterPage,
Linear-in-Density LUT into Camera ie TFT= WRKSTN2A, C=2
- b) CT/MR images are not lutted by CT/MR, not lutted by MasterPage,
lutted by Camera ie TFT=VER693C0, C=6
Note: if from MasterPage both typeof images have to be printed, define on
MasterPage 2 printers with same IP and Port but different AEtitles
MasterPage Setup:
n on Communication->Directory->Add Menu:
n Name=DryView, Connection Type=DICOM, IP Address=accordingly
n DICOM: Port=5040, Called AE Title=8700, Calling AE Title=MasterPage
n DICOM: Supp.Services: Store=Off, Print=On, Query/Retrieve=Off, Worklist=Off
n Options: Print: Magnif.=NONE, Available=On, Title=14x17 in.
n Options: Print: Width=4096, Height=5220, Pixel Size=78
n Make an ECHO test, just to verify that the DICOM connection is working ok
n in order to print into Patient File / Print Layout:
n a) into Print / Print Setup Menu:
n select Name=DryView, Size=14x17, Add to Format menu=On
n Black&White=On, Color=Off, Bits per pixel=12, Background Color=Black
n Zoom=100, Copies=1, Trim around Image=Off, Trim around Division=On
n b) into Image/Zoom: FitToWindow=On (for True Size, FixedZoom100%=On)
n into Image: Annotations and Measurements=On, Measurement Scale=On
n into Image: DICOM informations=On, DICOM Overlays=On
n c) into Format: 1. 14x17 on DryView=On, Show Footer=On
n d) into Layout select the appropriate icon between the predifined ones
n e) into Orientation eg Portrait=On
MIM200 Setup:
n on Configure, Network:
n Node Name=MIM, IPAddr=accordingly
n Subnet Mask=accordingly, Gateway Addr=accordingly
n on Configure, Input, Network, Add:
n Protocol=DICOM 3.0, Log.Name=DICOM, Type/Com=Keypad/COM9
n on Configure, Destination, Add, Print, Direct, Qualified, 8700, Set:
n General: Log.Name=8700
n General: Database Name=8700, Model=8700, Memory=32
n Media Info: Media=35x43cm, 4096x5223, 5133, Blue
n Output Params: Cmd=SuperSet,Baud=19200,Data=8,Stop=1,Parity=None
n Output Params: Pixel=12, Header/Line, Transfer=2000 KHz, Acq=60
n Supported Item: Collation=On, Text=On, Tonescaling=On, Rotation=On
n Interpolation: NoMag=On, Bilin=On, Repl=On,Cubic Spline=On
n Format Types: Custom=On, Slide=On, Row Symmetric=On
n Format Types: 1, 2, 4, 6, 8, 9, 12, 15, 16, 20, 24, 30, 35=On
n Formatting: Aspect Ratio Mix Page=On, Image Size Mix in Std Fmt=On
n Formatting: DICOM Annotation Box=On, Req.Size Scale=On
n Formatting: Req.Size Mix in Row=On, Trim=On
n Formatting: Aspect Ratio Mix in Row=On, Image Size Mix in Row=On
n Formatting: Req.Image Size=On, Req.Size Mix on Page=On
n Formatting: True Landscape=On
n Formatting: Max Img Band=20, Max Band per Page=20, Max Img Col=0
n Formatting: Max Img Row=0, Min Horiz Sep=2, Min Vert Sep=2
n Formatting: Trim Width Enabled=2, Trim Width Disabled=0
n Formatting: Pixel Pitch=12.8205
n Image Processing: Grayscale=On, Minify=On, Max Image Dmax=3.1
n M952 Usage: Min H/V Mag=1, Max H/V Mag=64, Min Dmax 952=1.7
n on Configure, SCP Services, select the specific modality, Modify:
n PLUT=N, ToneScaling=PerceptionLUT (Always=Y)
n TFT/ULUT= a) Wrkstn2a.w87 or b) Ver693c0.w87 (Always=N)
n Contrast (dry)= a) 2 or b) 6 (Always=N)
n Image Dmin=0.00 (Always=N), Image Dmax=3.00 (Always=N)
n Smoothing Type=0 (Always=N), Image Polarity=Normal (Always=N)
n NeventReports=Off (Always=Y), Warning Status=On
n Print Date=Off, Print Time=Off, Page Number=Off, Hosp.Name=Off
n Modality ID=Off, Annotation Override=Off (Always=N)
n Minify/Scale=On, Crop=Off, Text Box Relocation=None
n Print Priority=Normal (Always=N), Border=3.99 (Always=N)
n Film Base=Blue Film (Always=N), Film Size=14INx17IN (Always=N)
n Negotiate Color Print=Off
DICOM Network
RS422
COPCIL Board 9-pole Plug
Copper Cable Control 9-pin
Kodak
MasterPage Workstation
Data 37-pin
Note: the TFT and Contrast into Kodak camera have to be configured differently
if images that have to be printed from MasterPage are either
a) Kodak CR images or b) CT/MR images
- a) Kodak CR images are already lutted by Kodak CR, not lutted by MasterPage,
Linear-in-Density LUT into Camera ie TFT= WRKSTN2A, C=2
- b) CT/MR images are not lutted by CT/MR, not lutted by MasterPage,
lutted by Camera ie TFT=VER693C0, C=6
Note: if from MasterPage both typeof images have to be printed, define on
MasterPage 2 printers with same IP and Port but different AEtitles
MasterPage Setup:
n on Communication->Directory->Add Menu:
n Name=DryView, Connection Type=DICOM, IP Address=accordingly
n DICOM: Port=5040, Called AE Title=8100, Calling AE Title=MasterPage
n DICOM: Supp.Services: Store=Off, Print=On, Query/Retrieve=Off, Worklist=Off
n Options: Print: Magnif.=NONE, Available=On, Title=14x17 in.
n Options: Print: Width=4096, Height=5216, Pixel Size=78
n Make an ECHO test, just to verify that the DICOM connection is working ok
n in order to print into Patient File / Print Layout:
n a) into Print / Print Setup Menu:
n select Name=DryView, Size=14x17, Add to Format menu=On
n Black&White=On, Color=Off, Bits per pixel=12, Background Color=Black
n Zoom=100, Copies=1, Trim around Image=Off, Trim around Division=On
n b) into Image/Zoom: FitToWindow=On (for True Size, FixedZoom100%=On)
n into Image: Annotations and Measurements=On, Measurement Scale=On
n into Image: DICOM informations=On, DICOM Overlays=On
n c) into Format: 1. 14x17 on DryView=On, Show Footer=On
n d) into Layout select the appropriate icon between the predifined ones
n e) into Orientation eg Portrait=On
MIM200 Setup:
n on Configure, Network:
n Node Name=MIM, IPAddr=accordingly
n Subnet Mask=accordingly, Gateway Addr=accordingly
n on Configure, Input, Network, Add:
n Protocol=DICOM 3.0, Log.Name=DICOM, Type/Com=Keypad/COM9
n on Configure, Destination, Add, Print, Direct, Qualified, 8100, Set:
n General: Log.Name=8100
n General: Database Name=8100, Model=8100, Memory=32
n Media Info: Media=35x43cm, 4096x5223, 5133, Blue
n Output Params: Cmd Set=952, Baud=1200, Data=8, Stop=1, Parity=Even
n Output Params: Pixel=12, Header/Line, Transfer=1000 KHz, Acquire=60
n Supported Item: Collation=On, Text=On, Tonescaling=On, Rotation=On
n Interpolation: NoMag=On, Bilin=On, Repl=On,Cubic Spline=On
n Format Types: Custom=On, Slide=On, Row Symmetric=On
n Format Types: 1, 2, 4, 6, 8, 9, 12, 15, 16, 20, 24, 30, 35=On
n Formatting: Aspect Ratio Mix Page=On, Image Size Mix in Std Fmt=On
n Formatting: DICOM Annotation Box=On, Req.Size Scale=On
n Formatting: Req.Size Mix in Row=On, Trim=On
n Formatting: Aspect Ratio Mix in Row=On, Image Size Mix in Row=On
n Formatting: Req.Image Size=On, Req.Size Mix on Page=On
n Formatting: True Landscape=On
n Formatting: Max Img Band=20, Max Band per Page=20, Max Img Col=0
n Formatting: Max Img Row=0, Min Horiz Sep=2, Min Vert Sep=2
n Formatting: Trim Width Enabled=2, Trim Width Disabled=0
n Formatting: Pixel Pitch=12.8205
n Image Processing: Grayscale=On, Minify=On, Max Image Dmax=3.1
n M952 Usage: Min H/V Mag=1, Max H/V Mag=64, Min Dmax 952=1.7
n on Configure, SCP Services, select the specific modality, Modify:
n PLUT=N, ToneScaling=PerceptionLUT (Always=Y)
n TFT/ULUT= a) Wrkstn2a.w87 or b) Ver693c0.w87 (Always=N)
n Contrast (dry)= a) 2 or b) 6 (Always=N)
n Image Dmin=0.00 (Always=N), Image Dmax=3.00 (Always=N)
n Smoothing Type=0 (Always=N), Image Polarity=Normal (Always=N)
n NeventReports=Off (Always=Y), Warning Status=On
n Print Date=Off, Print Time=Off, Page Number=Off, Hosp.Name=Off
n Modality ID=Off, Annotation Override=Off (Always=N)
n Minify/Scale=On, Crop=Off, Text Box Relocation=None
n Print Priority=Normal (Always=N), Border=3.99 (Always=N)
n Film Base=Blue Film (Always=N), Film Size=14INx17IN (Always=N)
n Negotiate Color Print=Off
DICOM Network
Control 9 pin
Kodak COPCIL board
MasterPage Workstation Copper Cable
Data 37 pin
Note: TFT/ULUT and Contrast into Kodak camera have to be configured differently
if images that have to be printed from MasterPage are either
a) Kodak CR images or b) CT/MR images
- a) Kodak CR images are already lutted by Kodak CR, not lutted by MasterPage,
Linear-in-Density LUT into Camera ie TFT/ULUT= wrkstn83a.w8u, C=1
- b) CT/MR images are not lutted by CT/MR, not lutted by MasterPage,
lutted by Camera ie TFT/ULUT= u1_109b.w8u, C=10
Note: if from MasterPage both typeof images have to be printed, define on
MasterPage 2 printers with same IP and Port but different AEtitles
n d) into Layout select the appropriate icon between the predifined ones
n e) into Orientation select Portrait=On (note: Landscape selection will not work)
MIM200 Setup:
n on Configure, Network:
n Node Name=MIM, IPAddr=accordingly
n Subnet Mask=accordingly, Gateway Addr=accordingly
n on Configure, Input, Network, Add:
n Protocol=DICOM 3.0, Log.Name=DICOM, Type/Com=Keypad/COM9
n on Configure, Destination, Add, Print, Direct, Qualified, 8300, Set:
n General: Log.Name=8300
n General: Database Name=8300, Model=8300, Memory=32
n Media Info: Media=8x10in, 2256x2676, 2596, Blue
n Output Params: Cmd Set=952, Baud=1200, Data=8, Stop=1, Parity=Even
n Output Params: Pixel=8, Header/Line, Transfer=2000 KHz, Acquire=60
n Supported Item: Collation=On, Text=On, Tonescaling=On, Rotation=On
n Interpolation: NoMag=On, Bilin=On, Repl=On,Cubic Spline=On
n Format Types: Custom=On, Slide=On, Row Symm.=On, SuperSlide=On
n Format Types: 1, 2, 4, 6, 8, 9, 12, 15, 16, 20, 24, 30, 35=On
n Formatting: Aspect Ratio Mix Page=On, Image Size Mix in Std Fmt=On
n Formatting: DICOM Annotation Box=On, Req.Size Scale=On
n Formatting: Req.Size Mix in Row=On, Trim=On
n Formatting: Aspect Ratio Mix in Row=On, Image Size Mix in Row=On
n Formatting: Req.Image Size=On, Req.Size Mix on Page=On
n Formatting: True Landscape=On
n Formatting: Max Img Band=20, Max Band per Page=20, Max Img Col=0
n Formatting: Max Img Row=0, Min Horiz Sep=2, Min Vert Sep=2
n Formatting: Trim Width Enabled=2, Trim Width Disabled=0
n Formatting: Pixel Pitch=11.9048
8300 Setup:
n on Operator Menu set: D=16, C=6, Sharp/Smooth=0 ie Auto
n on Operator Menu set: Film Layout: 1 on 1=Portrait
n on Service Menu set: Ratio=1.00, Serial=1200,8,1,Even,Comma,3M, Memory=16
n on Service Menu set: Digital Interface: Parity=Even, Modality Group=1
DICOM Network
Data 37 pin
MasterPage Setup:
n on Communication->Directory->Add Menu:
n Name=DryView, Connection Type=DICOM, IP Address=accordingly
n DICOM: Port=5040, Called AE Title=8610, Calling AE Title=MasterPage
n DICOM: Supp.Services: Store=Off, Print=On, Query/Retrieve=Off, Worklist=Off
n Options: Print: Magnif.=NONE, Available=On, Title=8x10 in.
n Options: Print: Width=5024, Height=6200, Pixel Size=39
n Make an ECHO test, just to verify that the DICOM connection is working ok
n in order to print into Patient File / Print Layout:
n a) into Print / Print Setup Menu:
n select Name=DryView, Size=8x10, Add to Format menu=On
n Black&White=On, Color=Off, Bits pixel=12 (8 if 8600), Background Color=Black
n Zoom=100, Copies=1, Trim around Image=Off, Trim around Division=On
n b) into Image/Zoom: FitToWindow=On (for True Size, FixedZoom100%=On)
n into Image: Annotations and Measurements=On, Measurement Scale=On
n into Image: DICOM informations=On, DICOM Overlays=On
MIM200 Setup:
n on Configure, Network:
n Node Name=MIM, IPAddr=accordingly
n Subnet Mask=accordingly, Gateway Addr=accordingly
n on Configure, Input, Network, Add:
n Protocol=DICOM 3.0, Log.Name=DICOM, Type/Com=Keypad/COM9
n on Configure, Destination, Add, Print, Direct, Qualified, 8610 (or 8600), Set:
n General: Log.Name=8610 (or 8600)
n General: Database=8610 (or 8600), Model=8610 (or 8600), Memory=32
n Media Info: Media=8x10in, 5025x6200, 6020, Blue
n Output Params: Cmd Set=952, Baud=1200, Data=8, Stop=1, Parity=Even
n Output Params: Pixel=12 (8 if 8600), Header/Line,Transfer=2000,Acq=60
n Supported Item: Collation=On, Text=On, Tonescaling=On, Rotation=On
n Interpolation: NoMag=On, Bilin=On, Repl=On,Cubic Spline=On
n Format Types: Custom=On, Slide=On, Row Symmetric=On
n Format Types: 1, 2, 4, 6, 8, 9, 12, 15, 16, 20, 24, 30, 35=On
n Formatting: Aspect Ratio Mix Page=On, Image Size Mix in Std Fmt=On
n Formatting: DICOM Annotation Box=On, Req.Size Scale=On
n Formatting: Req.Size Mix in Row=On, Trim=On
n Formatting: Aspect Ratio Mix in Row=On, Image Size Mix in Row=On
n Formatting: Req.Image Size=On, Req.Size Mix on Page=On
n Formatting: True Landscape=On
n Formatting: Max Img Band=20, Max Band per Page=20, Max Img Col=0
n Formatting: Max Img Row=0, Min Horiz Sep=2, Min Vert Sep=2
n Formatting: Trim Width Enabled=2, Trim Width Disabled=0
n Formatting: Pixel Pitch=25.8065
n Image Processing: Grayscale=On, Minify=On, Max Image Dmax=3.5
n M952 Usage: Min H/V Mag=0.26, Max H/V Mag=16, Min Dmax 952=2
n on Configure, SCP Services, select the specific modality, Modify:
n PLUT=N, ToneScaling=PerceptionLUT (Always=Y)
n Contrast (dry)=a) 6 or b) 3 (Always=N), Modality Group=a) 1 or b) 6,
n Conv.Group=1, Gamma Table=Linear in a) Density or b) Transmittance
n Image Dmin=0.00 (Always=N), Image Dmax=3.50 (Always=N)
n Smoothing Type=1 (Always=Y), Image Polarity=Normal (Always=N)
n NeventReports=Off (Always=Y), Warning Status=On
n Print Date=Off, Print Time=Off, Page Number=Off, Hosp.Name=Off
n Modality ID=Off, Annotation Override=Off (Always=N)
n Minify/Scale=On, Crop=Off, Text Box Relocation=None (Always=N)
n Print Priority=Normal (Always=N), Border=3.99 (Always=N)
n Film Base=Blue Film (Always=N), Film Size=8INx10IN (Always=N)
n Negotiate Color Print=Off
8610 Setup: on 8610 Operator Menu into Test Menu, Software Version, verify:
n Imager=2.4, VRTX32=1.08, Contrast=6.P.2, Conv.Kernel=M.1.0
n (if 8600: Imager=2.5, Contrast=6.G.7, Conv.Kernel=1.0.5)
3 M H Q L aser Im ag er
Kodak
Fiber Cable
MasterPage Workstation
Fiber Cable
Note: the TFT and Contrast into Kodak camera have to be configured differently
if images that have to be printed from MasterPage are either
a) Kodak CR images or b) CT/MR images
- a) Kodak CR images are already lutted by Kodak CR, not lutted by MasterPage,
Linear-in-Density LUT into Camera ie TFT= WRKSTN2A, C=2
- b) CT/MR images are not lutted by CT/MR, not lutted by MasterPage,
lutted by Camera ie TFT=VER693C0, C=6
Note: if from MasterPage both typeof images have to be printed, define on
MasterPage 2 printers with same IP and Port but different AEtitles
MasterPage Setup:
n on Communication->Directory->Add Menu:
n Name=DryView, Connection Type=DICOM, IP Address=accordingly
n DICOM: Port=5040, Called AE Title=969, Calling AE Title=MasterPage
n DICOM: Supp.Services: Store=Off, Print=On, Query/Retrieve=Off, Worklist=Off
n Options: Print: Magnif.=NONE, Available=On, Title=14x17 in.
n Options: Print: Width=4096, Height=4992, Pixel Size=82
n Make an ECHO test, just to verify that the DICOM connection is working ok
n in order to print into Patient File / Print Layout:
n a) into Print / Print Setup Menu:
n select Name=DryView, Size=14x17, Add to Format menu=On
n Black&White=On, Color=Off, Bits per pixel=12, Background Color=Black
n Zoom=100, Copies=1, Trim around Image=Off, Trim around Division=On
n b) into Image/Zoom: FitToWindow=On (for True Size, FixedZoom100%=On)
n into Image: Annotations and Measurements=On, Measurement Scale=On
n into Image: DICOM informations=On, DICOM Overlays=On
n c) into Format: 1. 14x17 on DryView=On, Show Footer=On
n d) into Layout select the appropriate icon between the predifined ones
MIM200 Setup:
n on Configure, Network:
n Node Name=MIM, IPAddr,Subnet Mask,Gateway Addr=accordingly
n on Configure, Input, Network, Add:
n Protocol=DICOM 3.0, Log.Name=DICOM, Type/Com=Keypad/COM9
n on Configure, Destination, Add, Print, Direct, Qualified, 969, Set:
n General: Log.Name=969
n General: Database Name=969, Model=969, Memory=32
n Media Info: Media=35x43cm, 4096x5002, 4912, Blue
n Media Info: Media= 11x14in, 3030x4096, 4006, Blue
n Media Info: Media= 8x10in, 2086x2929, 2839, Blue
n Output Params: Cmd=SuperSet,Baud=19200,Data=8,Stop=1,Parity=None
n Output Params: Pixel=12, Header/Line, Transfer=2000 KHz, Acq=60
n Supported Item: Collation=On, Text=On, Tonescaling=On, Rotation=On
n Interpolation: Bilin=On, Repl=On,Cubic Spline=On
n Format Types: Custom=On, Slide=On, Row Symmetric=On
n Format Types: 1, 2, 4, 6, 8, 9, 12, 15, 16, 20, 24, 30, 35=On
n Formatting: Aspect Ratio Mix on Page=On, Image Size Mix in Std Fmt=On
n Formatting: DICOM Annotation Box=On, Req.Size Scale=On
n Formatting: Req.Size Mix in Row=On, Trim=On
n Formatting: Aspect Ratio Mix in Row=On, Image Size Mix in Row=On
n Formatting: Req.Image Size=On, Req.Size Mix on Page=On
n Formatting: True Landscape=On
n Formatting: Max Img per Band=20, Max Band per Page=20, Max Img Col=0
n Formatting: Max Img Row=0, Min Horiz Sep=2, Min Vert Sep=6
n Formatting: Trim Width Enabled=2, Trim Width Disabled=0
n Formatting: Pixel Pitch=12.3457
n Image Processing: Grayscale=On, Minify=On, Max Image Dmax=3.2
n M952 Usage: Min H/V Mag=0.26, Max H/V Mag=64, Min Dmax 952=1.7
n on Configure, SCP Services, select the specific modality, Modify:
n PLUT=N, ToneScaling=PerceptionLUT (Always=Y)
n TFT/ULUT= a) Wrkstn2a.w87 or b) Ver693c0.w87 (Always=N)
n Contrast (dry)= a) 2 or b) 6 (Always=N)
n Image Dmin=0.00 (Always=N), Image Dmax=3.00 (Always=N)
n Smoothing Type=0 (Always=N), Image Polarity=Normal (Always=N)
n NeventReports=Off (Always=Y), Warning Status=On
n Print Date=Off, Print Time=Off, Page Number=Off, Hosp.Name=Off
n Modality ID=Off, Annotation Override=Off (Always=N)
n Minify/Scale=On, Crop=Off, Text Box Relocation=None
n Print Priority=Normal (Always=N), Border=3.99 (Always=N)
n Film Base=Blue Film (Always=N), Film Size=14INx17IN (Always=N)
n Negotiate Color Print=Off
969 Setup:
n on COMM Menu: 969 Default
n on IMAGE Menu: TFT=VER693C0, Dmax=3.00, Contrast=6, Density=14
n on EIB Menu: Pixel=12, Header/Line, Port=0, Parity=Enable Even, Timeout=60
DICOM Network
Kodak
MasterPage Workstation
Note: the TFT and Contrast into Kodak camera have to be configured differently
if images that have to be printed from MasterPage are either
a) Kodak CR images or b) CT/MR images
- a) Kodak CR images are already lutted by Kodak CR, not lutted by MasterPage,
Linear-in-Density LUT into Camera ie TFT= WRKSTN2A, C=2
- b) CT/MR images are not lutted by CT/MR, not lutted by MasterPage,
lutted by Camera ie TFT=VER693C0, C=6
Note: if from MasterPage both typeof images have to be printed, define on
MasterPage 2 printers with same IP and Port but different AEtitles
MasterPage Setup:
n on Communication->Directory->Add Menu:
n Name=DryView, Connection Type=DICOM, IP Address=accordingly
n DICOM: Port=5040, Called AE Title=8900, Calling AE Title=MasterPage
n DICOM: Supp.Services: Store=Off, Print=On, Query/Retrieve=Off, Worklist=Off
n Options: Print: Magnif.=REPLICATE, Available=On, Title=14x17 in.
n Options: Print: Width=4488, Height=5464, Pixel Size=78
n Make an ECHO test, just to verify that the DICOM connection is working ok
n in order to print into Patient File / Print Layout:
n a) into Print / Print Setup Menu:
n select Name=DryView, Size=14x17, Add to Format menu=On
n Black&White=On, Color=Off, Bits per pixel=12, Background Color=Black
8900 Setup:
n on Configuration, System, Network:
n Host Name=DV8900, IPAddr=accordingly
n Subnet Mask=accordingly, Gateway Addr=accordingly
n on Configuration, DICOM SCP, Communications:
n Port=5040, Association Limit=12, Source Name=DICOM
n on Configuration, Destination:
n General: Log.Name=8900
n Media Types: Media=35x43cm, 9100x11037, 10781, Any
n Media Types: Media=35x35cm,9100x9087, 8831, Any
n Media Types: Media=11x14in, 7137x9100, 8844, Any
n Media Types: Media=10x12in, 6490x7767, 7511, Any
n Media Types: Media=8x10in, 5167x6490, 6234, Any
n Formatting: Aspect Ratio Mix Page=On, Aspect Ratio Mix Row=On
n Formatting: Image Size Mix in Std Fmt=On, Image Size Mix Row=On
n Formatting: DICOM Annotation Box=On, Req.Image Size=On
n Formatting: Req.Size Scale=On, Req.Size Mix Page=On
n Formatting: Req.Size Mix Row=On, Trim=On,
n Formatting: True Landscape=On, Rotation=On
n Formatting: Minify/Crop=On, Tonescaling on Image Basis=On
n Formatting: Max Img Band=7, Max Band Page=7, Max Img Cols=0
n Formatting: Max Img Rows=0, Pixel Pitch=25.5910, Min Horiz Sep=4
n Formatting: Min Vert Sep=4, Trim Width Enabled=4
n Formatting: Trim Width Disabled=0, Maximum DMAX=3.30
n on Configuration, DICOM SCP, SCP Services, select specific modality, Modify:
n Negotiate Presentation LUT=No, Negotiate Color Print=No
n TFT/ULUT= a) Wrkstn2a.w87 or b) Ver693c0.w87 (Always=Y)
n Contrast= a) 2 or b) 6 (Always=Y)
n Smoothing Type=0 (Always=Y), Image Polarity (Always=N)
n Image Dmin=0.00 (Always=N), Image Dmax=3.00 (Always=N)
n NeventReports=No (Always=Y), Warnings=Yes
n Print Priority=Normal (Always=N), Border=3.99 (Always=N)
n 2mm Border=Yes, Film Clip Border=No, Film Base=Blue Film (Always=N)
n Film Size=14INx17IN (Always=N), Sorter Bin=Bin1 (Always=N)
n Print Date=No, Print Time=No, Page Nbr=No, Hosp.Name=No
n Modality ID=No, Annotation Override=No, Density Patch=No
n Image Resizing=Minify/Scale (Always=N),
n Text Box Location=None, Source ID=mp
DICOM Network
Kodak
MasterPage Workstation
Note: the TFT and Contrast into Kodak camera have to be configured differently
if images that have to be printed from MasterPage are either
a) Kodak CR images or b) CT/MR images
- a) Kodak CR images are already lutted by Kodak CR, not lutted by MasterPage,
Linear-in-Density LUT into Camera ie TFT= WRKSTN2A, C=1
- b) CT/MR images are not lutted by CT/MR, not lutted by MasterPage,
lutted by Camera ie TFT=VER693C0, C=6
Note: if from MasterPage both typeof images have to be printed, define on
MasterPage 2 printers with same IP and Port but different AEtitles
MasterPage Setup:
n on Communication->Directory->Add Menu:
n Name=DryView, Connection Type=DICOM, IP Address=accordingly
n DICOM: Port=5040, Called AE Title=DV8150, Calling AE Title=MasterPage
n DICOM: Supp.Services: Store=Off, Print=On, Query/Retrieve=Off, Worklist=Off
n Options: Print: Magnif.=REPLICATE, Available=On, Title=14x17 in.
n Options: Print: Width=4438, Height=5390, Pixel Size=78
n Make an ECHO test, just to verify that the DICOM connection is working ok
n in order to print into Patient File / Print Layout:
n a) into Print / Print Setup Menu:
n select Name=DryView, Size=14x17, Add to Format menu=On
n Black&White=On, Color=Off, Bits per pixel=12, Background Color=Black
n Zoom=100, Copies=1, Trim around Image=Off, Trim around Division=On
n b) into Image/Zoom: FitToWindow=On (for True Size, FixedZoom100%=On)
n into Image: Annotations and Measurements=On, Measurement Scale=On
n into Image: DICOM informations=On, DICOM Overlays=On
n c) into Format: 1. 14x17 on DryView=On, Show Footer=On
n d) into Layout select the appropriate icon between the predifined ones
n e) into Orientation eg Portrait=On
8150 Setup:
n on Configuration, System, Network:
n Host Name=DV8150DRE, IPAddr=accordingly
n Subnet Mask=accordingly, Gateway Addr=accordingly
n on Configuration, DICOM SCP, Communications:
n Port=5040, Association Limit=12, Source Name=DICOM
n on Configuration, Destination:
n AE Title: Log.Name=DV8150
n Media Types: Media=35x43cm, 4438x5390, 5262, Any
n Media Types: Media=35x35cm, 4438x4414,4286, Any
n Media Types: Media=11x14in, 3440x4438, 4310, Any
n Formatting: Aspect Ratio Mix Page=On, Aspect Ratio Mix Row=On
n Formatting: Image Size Mix in Std Fmt=On, Image Size Mix Row=On
n Formatting: DICOM Annotation Box=On, Req.Image Size=On
n Formatting: Req.Size Scale=On, Req.Size Mix Page=On
n Formatting: Req.Size Mix Row=On, Trim=On,
n Formatting: True Landscape=On, Rotation=On
n Formatting: Minify/Crop=On, Tonescaling on Image Basis=On
n Formatting: Max Img Band=7, Max Band Page=7, Max Img Cols=0
n Formatting: Max Img Rows=0, Pixel Pitch=12.8000, Min Horiz Sep=2
n Formatting: Min Vert Sep=2, Trim Width Enabled=2
n Formatting: Trim Width Disabled=0, Maximum DMAX=3.10
n on Configuration, DICOM SCP, SCP Services, select specific modality, Modify:
n Negotiate Presentation LUT=No, Negotiate Color Print=No,
n TFT Set Name=a) Wrkstn2a.w87 or b) Ver693c0.w87 (Always=Y)
n Contrast=a) 1 or b) 6 (Always=N), Smoothing Type=0 (Always=N)
n Dmin=0.00 (Always=N), Dmax=3.00 (Always=N)
n Image Polarity=Normal (Always=N)
n NeventReports=No (Always=Y), Warnings=Yes
n Print Priority=Normal (Always=N), Border=3.99 (Always=N)
n 2mm Border=Yes, Film Clip Border=No,
n Film Base=Blue Film (Always=N), Film Size=14INx17IN (Always=N)
n Print Date=No, Print Time=No, Page Nbr=No, Hosp.Name=No,
n Modality ID=No, Annotation Override=No, Density Patch=No
n Image Resizing=Minify/Scale (Always=N),
n Text Box Location=None, Source ID=ws
DICOM Network
Kodak
MasterPage Workstation
Note: the TFT and Contrast into Kodak camera have to be configured differently
if images that have to be printed from MasterPage are either
a) Kodak CR images or b) CT/MR images
- a) Kodak CR images are already lutted by Kodak CR, not lutted by MasterPage,
Linear-in-Density LUT into Camera ie TFT= WRKSTN2A, C=7
- b) CT/MR images are not lutted by CT/MR, not lutted by MasterPage,
lutted by Camera ie TFT=VER693C0, C=6
Note: if from MasterPage both typeof images have to be printed, define on
MasterPage 2 printers with same IP and Port but different Aetitles
MasterPage Setup:
n on Communication->Directory->Add Menu:
n Name=CMI1000, Connection Type=DICOM, IP Address=accordingly
n DICOM: Port=5040, Called AE Title=CMI1000, Calling AE Title=MasterPage
n DICOM: Supp.Services: Store=Off, Print=On, Query/Retrieve=Off, Worklist=Off
n Options: Print: Magnif.=REPLICATE, Available=On, Title=8x10 in.
n Options: Print: Width=2508, Height=3134 if A4 (or 2954 if Letter), Pixel Size=81
n Make an ECHO test, just to verify that the DICOM connection is working ok
n in order to print into Patient File / Print Layout:
n a) into Print / Print Setup Menu:
n select Name=CMI1000, Size=8x10, Add to Format menu=On
n Black&White=Off, Color=On, Bits per pixel=8, Background Color=Black
n Zoom=100, Copies=1, Trim around Image=Off, Trim around Division=On
n b) into Image/Zoom: FitToWindow=On (for True Size, FixedZoom100%=On)
n into Image: Annotations and Measurements=On, Measurement Scale=On
n into Image: DICOM informations=On, DICOM Overlays=On
n c) into Format: 1. 8x10 on CMI1000=On, Show Footer=On
n d) into Layout select the appropriate icon between the predifined ones
n e) into Orientation eg Portrait=On
CMI-1000 Setup:
at Local Panel, under Media, set A4 or Letter ie what inside Paper Tray
1
setup valid also for Kodak PACS LINK 25 PRINT SERVER.
DICOM Network
Kodak MedView
Workstation
MedView Setup:
n on Print->Destinations->Add Menu:
n General: Class=DICOM Printer, Name=DryView
n DICOM: AE Title=8300, Host Name=IP-Address of 8300
n DICOM: Port=104, Destination=Processor, Enable Print Job Events=Off
n DICOM: Compose Sheet=Off, BFS Print Support=Off
n DICOM film: Magnif.=Cubic, Medium=Blue Film, Smoothing=0
n DICOM film: Config Info= LUT=0,10, Border=Black, MaxDensity=300
n DICOM media: 8INx10IN
n Layouts: 1,1; 1,2; 2,2; 2,3
n Image: Min.Bitmap Size=256, Bit Depth=8, Orig.Size=Off, Color=Monochrome
8300 Setup:
n on 8300 Operator Menu into Configure User set:
n Density=16, Contrast=10, Sharp/Smooth=0 ie Auto
n on 8300 Service Menu into Configure User set: Modality Group=0
DICOM Network
MedView Setup:
n on Print->Destinations->Add Menu:
n General: Class=DICOM Printer, Name=K190
n DICOM: AE Title=190, Host Name=IP-Address of 190
n DICOM: Port=5040, Destination=Processor, Enable Print Job Events=Off
n DICOM: Compose Sheet=Off, BFS Print Support=Off
n DICOM film: Magnif.=Cubic, Medium=Blue Film, Smoothing=Normal
n DICOM film: Config Info=CS435\CN0\PD1.2, Border=Black, MaxDensity=300
n DICOM media: 14INx17IN
n Layouts: 1,1; 1,2; 2,2; 2,3; 3,3; 3,4; 3,5; 4,4; 4,5
n Image: Min.Bitmap Size=256, Bit Depth=8, Orig.Size=Off, Color=Monochrome
190 Setup:
n On 190 Control Panel press Menu, Setup:
n Printer Density=3.00, Curve Shape=3.0, Contrast=0, Contrast Pivot Density=1.2
n IPAddress=accordingly, Subnet Mask=accordingly, Gateway Address=accordingly
n Port=5040, Network Node Name=Kodak MLP190, Connection Type=RJ45
Workstation
Fiber Cable
MedView Setup:
n on Print->Destinations->Add Menu:
n General: Class=DICOM Printer, Name=DryView
n DICOM: AE Title=9410, Host Name=IP-Address of 9410
n DICOM: Port=1024, Destination=Processor, Enable Print Job Events=Off
n DICOM: Compose Sheet=Off, BFS Print Support=Off
n DICOM film: Magnif.=Cubic, Medium=Blue Film, Smoothing=2
n DICOM film: Config Info= LUT=0,9, Border=Black, MaxDensity=300
n DICOM media: 14INx17IN (11INx14IN if 8500)
n Layouts: 1,1; 1,2; 2,2; 2,3; 3,3; 3,4; 3,5; 4,4; 4,5
n Image: Min.Bitmap Size=256, Bit Depth=8, Orig.Size=Off, Color=Monochrome
9410 Setup:
n on Device Setup, LOCAL PRINTERS:
n Printer=8700, Model=8700, Output=Fiber
n Command Set=Superset, Baud=19200, Data=8, Stop=1, Parity=None
n Pixel=12, Header/Line, Timeout=60, Transfer Rate=2 MHz
n Film Mismatch=Print Always, Interpolation Type=831
n Interp Num=2, Max.Density=300, Contrast=6, Border Density=0
n TFT/ULUT Emulation=On, Installed TFT/ULUT=Ver693c0.w87
n on Device Setup, SCP PRINTERS, Current Providers:
n Printer=8700, AE Title= 9410, Port= 1024, Max Associations= 5
n on Device Setup, SCP PRINTERS, Registered Users:
DICOM Network
RS422
COPCIL Board 9-pole Plug
Copper Cable Control 9-pin
Kodak MedView
Workstation
Data 37-pin
MedView Setup:
n on Print->Destinations->Add Menu:
n General: Class=DICOM Printer, Name=DryView
n DICOM: AE Title=9410, Host Name=IP-Address of 9410
n DICOM: Port=1024, Destination=Processor, Enable Print Job Events=Off
n DICOM: Compose Sheet=Off, BFS Print Support=Off
n DICOM film: Magnif.=Cubic, Medium=Blue Film, Smoothing=2
n DICOM film: Config Info= LUT=0,9, Border=Black, MaxDensity=300
n DICOM media: 14INx17IN
n Layouts: 1,1; 1,2; 2,2; 2,3; 3,3; 3,4; 3,5; 4,4; 4,5
n Image: Min.Bitmap Size=256, Bit Depth=8, Orig.Size=Off, Color=Monochrome
9410 Setup:
on Device Setup, LOCAL PRINTERS:
n Printer=8100, Model=8100 4096 pxls/line, Output=Copper
n Baud=1200, Parity=Even, Data=8, Stop=1, Command Set=952
n Pixel=12, Header/Line, Timeout=60, Transfer Rate=1 MHz
n Film Mismatch=Print Always, Interpolation Type=831
n Interp Num=2, Max.Density=300, Contrast=6, Border Density=0
n TFT/ULUT Emulation=On, Installed TFT/ULUT=Ver693c0.w87
on Device Setup, SCP PRINTERS, Current Providers:
n Printer=8100, AE Title= 9410, Port= 1024, Max Associations= 5
on Device Setup, SCP PRINTERS, Registered Users:
n SCU AETitle= accordingly, SCU IPAddr=accordingly
n SCP=8100, Copies=1, Contrast Table=9, TFT/ULUT=Pmsb.w87
n Max.Density=300, Border Density=0, Mag.Type=8, Smoothing=2
n Polarity=1, Orientation=1, Set Req.Image Size=No, Priority=Low
n Interceptor=Yes, N-Event-Print Job=No, N-Event Printer=No
DICOM Network
Control 9 pin
Kodak MedView COPCIL board
Workstation Copper Cable
Data 37 pin
MedView Setup:
n on Print->Destinations->Add Menu:
n General: Class=DICOM Printer, Name=DryView
n DICOM: AE Title=9410, Host Name=IP-Address of 9410
n DICOM: Port=1024, Destination=Processor, Enable Print Job Events=Off
n DICOM: Compose Sheet=Off, BFS Print Support=Off
n DICOM film: Magnif.=Cubic, Medium=Blue Film, Smoothing=0
n DICOM film: Config Info= LUT=0,10, Border=Black, MaxDensity=300
n DICOM media: 8INx10IN
n Layouts: 1,1; 1,2; 2,2; 2,3
n Image: Min.Bitmap Size=256, Bit Depth=8, Orig.Size=Off, Color=Monochrome
9410 Setup:
n on Device Setup, LOCAL PRINTERS:
n Printer=8300, Model=8300 Copper, Output=Copper
n Command Set=952, Baud=1200, Data=8, Stop=1, Parity=Even
n Pixel=8, Header/Line, Timeout=60, Transfer Rate=1 MHz
n Film Mismatch=Print Always, Interpolation Type=831
n Interp Num=0, Max.Density=300, Contrast=6, Border Density=0
n TFT/ULUT Emulation=On, Installed TFT/ULUT=upmsv3k.w8u
n on Device Setup, SCP PRINTERS, Current Providers:
n Printer=8300, AE Title= 9410, Port= 1024, Max Associations= 5
n on Device Setup, SCP PRINTERS, Registered Users:
n SCU AETitle= accordingly, SCU IPAddr=accordingly
n SCP=8300, Copies=1, Contrast Table=10, TFT/ULUT=u1_109b.w8u
n Max.Density=300, Border Density=0, Mag.Type=8, Smoothing=0
n Polarity=1, Orientation=1, Set Req.Image Size=No, Priority=Low
8300 Setup:
n on Operator Menu set: D=16, C=6, Sharp/Smooth=0 ie Auto
n on Operator Menu set: Film Layout: 1 on 1=Portrait
n on Service Menu set: Ratio=1.00, Serial=1200,8,1,Even,Comma,3M, Memory=16
n on Service Menu set: Digital Interface: Parity=Even, Modality Group=1
DICOM Network
Kodak MedView
Workstation Kodak 160 camera
Crossed
Network Cable
MedView Setup:
n on Print->Destinations->Add Menu:
n General: Class=DICOM Printer, Name=K160
n DICOM: AE Title=160, Host Name=IP-Address of MIM200
n DICOM: Port=5040, Destination=Processor, Enable Print Job Events=Off
n DICOM: Compose Sheet=Off, BFS Print Support=Off
n DICOM film: Magnif.=Cubic, Medium=Blue Film, Smoothing=Normal
n DICOM film: Config Info=CS435\CN0\PD1.2, Border=Black, MaxDensity=300
n DICOM media: 14INx17IN
n Layouts: 1,1; 1,2; 2,2; 2,3; 3,3; 3,4; 3,5; 4,4; 4,5
n Image: Min.Bitmap Size=256, Bit Depth=8, Orig.Size=Off, Color=Monochrome
MIM200 Setup:
n on Configure, Network:
n Computer Name=eg Kodak160, IPAddr=accordingly
n Subnet Mask=accordingly, Gateway Addr=accordingly
n on Configure, Input, Network, Add:
n Protocol=DICOM 3.0, Log.Name=DICOM, Type/Com=Keypad/COM9
n on Configure, Destination, Add, Print, Direct, Qualified, KELI 160, Set:
n General: Log.Name=KELI 160, IPAddr=100.100.100.30,
n General: Database Name=KELI 160, Model=KELI 160
n Media Info: Media=35x43cm, 4361x5348, 5228, Any (Blue,Clear)
n Supported Item: Collation=On, Text=On, Tonescaling on Image=On
n Supported Item: Pivot Density=On, Rotation=On
n Interpolation: NoMag=On, Bil=On, Repl=On,Cubic=On, Cubic 2=On
n Format Types: Custom=On, Slide=On, Row Symmetric=On
n Format Types: 1, 2, 4, 6, 8, 9, 12, 15, 16, 20, 24, 30, 35=On
n Formatting: Aspect Ratio Mix Page=On, Image Size Mix in Std Fmt=On
n Formatting: DICOM Annotation Box=On, Req.Size Scale=On
n Formatting: Req.Size Mix in Row=On, Trim=On
n Formatting: Aspect Ratio Mix in Row=On, Image Size Mix in Row=On
n Formatting: Req.Image Size=On, Req.Size Mix on Page=On
n Formatting: True Landscape=On
n Formatting: Max Img Band=20, Max Band per Page=20, Max Img Col=0
n Formatting: Max Img Row=0, Min Horiz Sep=2, Min Vert Sep=2
n Formatting: Trim Width Enabled=2, Trim Width Disabled=0
n Formatting: Pixel Pitch=12.8
n Image Processing: Grayscale=On, Minify/Crop=On, Max Image Dmax=3.2
n M952 Usage: Min H/V Mag=0, Max H/V Mag=0, Min Dmax 952=1.7
n on Configure, SCP Services, select the specific modality, Modify:
n PLUT=N, ToneScaling=Curve Shape (Always=Y)
n Curve Shape= 3 ie 435 (Always=N), Contrast (wet)=0 (Always=Y)
n Image Dmin=0.00 (Always=N), Image Dmax=3.00 (Always=N)
n Interpolation=Cubic, Image Polarity=Normal (Always=N)
n NeventReports=Off (Always=Y), Warning Status=On
n Print Date=Off, Print Time=Off, Page Number=Off, Hosp.Name=Off
n Modality ID=Off, Annotation Override=Off (Always=N)
n Minify/Scale=On, Crop=Off, Text Box Relocation=None (Always=N)
n Print Priority=Normal (Always=N), Border=3.99 (Always=N)
n Film Base=Blue Film (Always=N), Film Size=14INx17IN (Always=N)
n Negotiate Color Print=Off
DICOM Network
Kodak MedView
Kodak 2180 camera
Workstation
Fiber Cable
MedView Setup:
n on Print->Destinations->Add Menu:
n General: Class=DICOM Printer, Name=K2180
n DICOM: AE Title=2180, Host Name=IP-Address of MIM200
n DICOM: Port=5040, Destination=Processor, Enable Print Job Events=Off
n DICOM: Compose Sheet=Off, BFS Print Support=Off
n DICOM film: Magnif.=Cubic, Medium=Blue Film, Smoothing=Normal
n DICOM film: Config Info=CS435\CN0\PD1.2, Border=Black, MaxDensity=300
n DICOM media: 14INx17IN, 14INx14IN, 11INx14IN, 8INx10IN
n Layouts: 1,1; 1,2; 2,2; 2,3; 3,3; 3,4; 3,5; 4,4; 4,5
n Image: Min.Bitmap Size=256, Bit Depth=8, Orig.Size=Off, Color=Monochrome
MIM200 Setup:
n on Configure, Network:
n Computer Name=eg Kodak2180, IPAddr=accordingly
n Subnet Mask=accordingly, Gateway Addr=accordingly
n on Configure, Input, Network, Add:
n Protocol=DICOM 3.0, Log.Name=DICOM, Type/Com=Keypad/COM9
n on Configure, Destination, Add, Print, Direct, Qualified, KELP 2180, Set:
n General: Log.Name=KELP2180, Database Name=KELP 2180
n General: Model=KELP 2180, Memory=24, Node ID=6 or accordingly
n Media Info: Media=35x43cm, 4136x5160, 5030, (Blue)
n Media Info:Media=35x35cm,4136x4136,4006, (Blue)
n Media Info: Media=11x14in, 3240x4136, 4006, (Blue)
n Media Info: Media=8x10in, 2290x2840, 2710, (Blue)
n Supported Item: Collation=On, Text=On, Tonescaling=On, Rotation=On
n Interpolation: NoMag=On, Bil=On, Repl=On,Cubic=On, Cubic 2=On
n Format Types: Custom=On, Slide=On, Row Symmetric=On
2180 Setup:
n Optical Interface board will automatic configure into 2180, no setup needed
DICOM Network
Kodak MedView
Kodak 1120 camera
Workstation
Fiber Cable
MedView Setup:
n on Print->Destinations->Add Menu:
n General: Class=DICOM Printer, Name=K1120
n DICOM: AE Title=1120, Host Name=IP-Address of MIM200
n DICOM: Port=5040, Destination=Processor, Enable Print Job Events=Off
n DICOM: Compose Sheet=Off, BFS Print Support=Off
n DICOM film: Magnif.=Cubic, Medium=Blue Film, Smoothing=Normal
n DICOM film: Config Info=CS435\CN0\PD1.2, Border=Black, MaxDensity=300
n DICOM media: 14INx17IN, 14INx14IN, 11INx14IN, 8INx10IN
n Layouts: 1,1; 1,2; 2,2; 2,3; 3,3; 3,4; 3,5; 4,4; 4,5
n Image: Min.Bitmap Size=256, Bit Depth=8, Orig.Size=Off, Color=Monochrome
MIM200 Setup:
n on Configure, Network:
n Computer Name=eg Kodak1120, IPAddr=accordingly
n Subnet Mask=accordingly, Gateway Addr=accordingly
n on Configure, Input, Network, Add:
n Protocol=DICOM 3.0, Log.Name=DICOM, Type/Com=Keypad/COM9
n on Configure, Destination, Add, Print, Direct, Qualified, KELP 1120, Set:
n General: Log.Name=KELP1120, Database Name=KELP 1120
n General: Model=KELP 1120, Memory=20, Node ID=6 or accordingly
n Media Info: Media=35x43cm, 4096x5132, 5034, (Blue)
n Media Info: Media=35x35cm, 4096x4108, 4010, (Blue)
n Media Info: Media=11x14in, 4096x3232, 3134, (Blue)
n Media Info: Media=8x10in, 2304x2900, 2802, (Blue)
n Supported Item: Collation=On, Text=On, Tonescaling=On, Rotation=On
n Interpolation: NoMag=On, Repl=On,Cubic Spline=On
1120 Setup:
n Optical Interface board will automatic configure into 1120, no setup needed
DICOM Network
Kodak MedView
Workstation
Crossed
Network Cable
MedView Setup:
n on Print->Destinations->Add Menu:
n General: Class=DICOM Printer, Name=DryView
n DICOM: AE Title=8200, Host Name=IP-Address of MIM200
n DICOM: Port=5040, Destination=Processor, Enable Print Job Events=Off
n DICOM: Compose Sheet=Off, BFS Print Support=Off
n DICOM film: Magnif.=Cubic, Medium=Blue Film, Smoothing=2
n DICOM film: Config Info= LUT=0,9, Border=Black, MaxDensity=300
n DICOM media: 14INx17IN, 14INx14IN, 11INx14IN
n Layouts: 1,1; 1,2; 2,2; 2,3; 3,3; 3,4; 3,5; 4,4; 4,5
n Image: Min.Bitmap Size=256, Bit Depth=8, Orig.Size=Off, Color=Monochrome
MIM200 Setup:
n on Configure, Network:
n Node Name=MIM, IPAddr=accordingly
n Subnet Mask=accordingly, Gateway Addr=accordingly
n on Configure, Input, Network, Add:
n Protocol=DICOM 3.0, Log.Name=DICOM, Type/Com=Keypad/COM9
n on Configure, Destination, Add, Print, Direct, Qualified, 8200, Set:
n General: Log.Name=8200, IPAddr=100.100.100.40,
n General: Database Name=8200, Model=8200, Memory=32
n Media Info: Media=35x43cm, 4361x5223, 5133, Blue
n Media Info: Media=35x35cm, 4361x4247, 4157, Blue
n Media Info: Media=11x14in, 3272x4361, 4271, Blue
n Supported Item: Collation=On, Common Text=On, Tonescaling=On
n Supported Item: Remote Image Deletion=On, Rotation=On
Workstation
Fiber Cable
MedView Setup:
n on Print->Destinations->Add Menu:
n General: Class=DICOM Printer, Name=DryView
n DICOM: AE Title=8700, Host Name=IP-Address of MIM200
n DICOM: Port=5040, Destination=Processor, Enable Print Job Events=Off
n DICOM: Compose Sheet=Off, BFS Print Support=Off
n DICOM film: Magnif.=Cubic, Medium=Blue Film, Smoothing=2
n DICOM film: Config Info= LUT=0,9, Border=Black, MaxDensity=300
n DICOM media: 14INx17IN (11INx14IN if 8500)
n Layouts: 1,1; 1,2; 2,2; 2,3; 3,3; 3,4; 3,5; 4,4; 4,5
n Image: Min.Bitmap Size=256, Bit Depth=8, Orig.Size=Off, Color=Monochrome
MIM200 Setup:
n on Configure, Network:
n Node Name=MIM, IPAddr=accordingly
n Subnet Mask=accordingly, Gateway Addr=accordingly
n on Configure, Input, Network, Add:
n Protocol=DICOM 3.0, Log.Name=DICOM, Type/Com=Keypad/COM9
n on Configure, Destination, Add, Print, Direct, Qualified, 8700, Set:
n General: Log.Name=8700
n General: Database Name=8700, Model=8700, Memory=32
n Media Info: Media=35x43cm, 4096x5223, 5133, Blue
n Output Params: Cmd=SuperSet,Baud=19200,Data=8,Stop=1,Parity=None
DICOM Network
RS422
COPCIL Board 9-pole Plug
Copper Cable Control 9-pin
Kodak MedView
Workstation
Data 37-pin
MedView Setup:
n on Print->Destinations->Add Menu:
n General: Class=DICOM Printer, Name=DryView
n DICOM: AE Title=8100, Host Name=IP-Address of MIM200
n DICOM: Port=5040, Destination=Processor, Enable Print Job Events=Off
n DICOM: Compose Sheet=Off, BFS Print Support=Off
n DICOM film: Magnif.=Cubic, Medium=Blue Film, Smoothing=2
n DICOM film: Config Info= LUT=0,9, Border=Black, MaxDensity=300
n DICOM media: 14INx17IN
n Layouts: 1,1; 1,2; 2,2; 2,3; 3,3; 3,4; 3,5; 4,4; 4,5
n Image: Min.Bitmap Size=256, Bit Depth=8, Orig.Size=Off, Color=Monochrome
MIM200 Setup:
n on Configure, Network:
n Node Name=MIM, IPAddr=accordingly
n Subnet Mask=accordingly, Gateway Addr=accordingly
n on Configure, Input, Network, Add:
n Protocol=DICOM 3.0, Log.Name=DICOM, Type/Com=Keypad/COM9
n on Configure, Destination, Add, Print, Direct, Qualified, 8100, Set:
n General: Log.Name=8100
n General: Database Name=8100, Model=8100, Memory=32
n Media Info: Media=35x43cm, 4096x5223, 5133, Blue
n Output Params: Cmd Set=952, Baud=1200, Data=8, Stop=1, Parity=Even
n Output Params: Pixel=12, Header/Line, Transfer=1000 KHz, Acquire=60
n Supported Item: Collation=On, Text=On, Tonescaling=On, Rotation=On
n Interpolation: NoMag=On, Bilin=On, Repl=On,Cubic Spline=On
n Format Types: Custom=On, Slide=On, Row Symmetric=On
DICOM Network
Control 9 pin
Kodak MedView COPCIL board
Workstation Copper Cable
Data 37 pin
MedView Setup:
n on Print->Destinations->Add Menu:
n General: Class=DICOM Printer, Name=DryView
n DICOM: AE Title=8300, Host Name=IP-Address of MIM200
n DICOM: Port=5040, Destination=Processor, Enable Print Job Events=Off
n DICOM: Compose Sheet=Off, BFS Print Support=Off
n DICOM film: Magnif.=Cubic, Medium=Blue Film, Smoothing=2
n DICOM film: Config Info= LUT=0,10, Border=Black, MaxDensity=300
n DICOM media: 8INx10IN
n Layouts: 1,1; 1,2; 2,2; 2,3
n Image: Min.Bitmap Size=256, Bit Depth=8, Orig.Size=Off, Color=Monochrome
MIM200 Setup:
n on Configure, Network:
n Node Name=MIM, IPAddr=accordingly
n Subnet Mask=accordingly, Gateway Addr=accordingly
n on Configure, Input, Network, Add:
n Protocol=DICOM 3.0, Log.Name=DICOM, Type/Com=Keypad/COM9
n on Configure, Destination, Add, Print, Direct, Qualified, 8300, Set:
n General: Log.Name=8300
n General: Database Name=8300, Model=8300, Memory=32
n Media Info: Media=8x10in, 2256x2676, 2596, Blue
n Output Params: Cmd Set=952, Baud=1200, Data=8, Stop=1, Parity=Even
n Output Params: Pixel=8, Header/Line, Transfer=2000 KHz, Acquire=60
n Supported Item: Collation=On, Text=On, Tonescaling=On, Rotation=On
n Interpolation: NoMag=On, Bilin=On, Repl=On,Cubic Spline=On
n Format Types: Custom=On, Slide=On, Row Symm.=On, SuperSlide=On
8300 Setup:
n on Operator Menu set: D=16, C=6, Sharp/Smooth=0 ie Auto
n on Operator Menu set: Film Layout: 1 on 1=Portrait
n on Service Menu set: Ratio=1.00, Serial=1200,8,1,Even,Comma,3M, Memory=16
n on Service Menu set: Digital Interface: Parity=Even, Modality Group=1
DICOM Network
Kodak MedView
Workstation
MedView Setup:
n on Print->Destinations->Add Menu:
n General: Class=DICOM Printer, Name=DryView
n DICOM: AE Title=8900, Host Name=IP-Address of 8900
n DICOM: Port=5040, Destination=Processor, Enable Print Job Events=Off
n DICOM: Compose Sheet=Off, BFS Print Support=Off
n DICOM film: Magnif.=Cubic, Medium=Blue Film, Smoothing=2
n DICOM film: Config Info= LUT=0,9, Border=Black, MaxDensity=300
n DICOM media: 14INx17IN, 14INx14IN, 11INx14IN, 10INx12IN, 8INx10IN
n Layouts: 1,1; 1,2; 2,2; 2,3; 3,3; 3,4; 3,5; 4,4; 4,5
n Image: Min.Bitmap Size=256, Bit Depth=8, Orig.Size=Off, Color=Monochrome
8900 Setup:
n on Configuration, System, Network:
n Host Name=DV8900, IPAddr=accordingly
n Subnet Mask=accordingly, Gateway Addr=accordingly
n on Configuration, DICOM SCP, Communications:
n Port=5040, Association Limit=12, Source Name=DICOM
n on Configuration, Destination:
n General: Log.Name=8900
n Media Types: Media=35x43cm, 9100x11037, 10781, Any
n Media Types: Media=35x35cm,9100x9087, 8831, Any
n Media Types: Media=11x14in, 7137x9100, 8844, Any
n Media Types: Media=10x12in, 6490x7767, 7511, Any
n Media Types: Media=8x10in, 5167x6490, 6234, Any
n Formatting: Aspect Ratio Mix Page=On, Aspect Ratio Mix Row=On
n Formatting: Image Size Mix in Std Fmt=On, Image Size Mix Row=On
n Formatting: DICOM Annotation Box=On, Req.Image Size=On
n Formatting: Req.Size Scale=On, Req.Size Mix Page=On
n Formatting: Req.Size Mix Row=On, Trim=On,
DICOM Network
Kodak MedView
Workstation
MedView Setup:
n on Print->Destinations->Add Menu:
n General: Class=DICOM Printer, Name=DryView
n DICOM: AE Title=DV8150, Host Name=IP-Address of 8150
n DICOM: Port=5040, Destination=Processor, Enable Print Job Events=Off
n DICOM: Compose Sheet=Off, BFS Print Support=Off
n DICOM film: Magnif.=Cubic, Medium=Blue Film, Smoothing=2
n DICOM film: Config Info= LUT=0,9, Border=Black, MaxDensity=300
n DICOM media: 14INx17IN, 14INx14IN, 11INx14IN, 10INx12IN, 8INx10IN
n Layouts: 1,1; 1,2; 2,2; 2,3; 3,3; 3,4; 3,5; 4,4; 4,5
n Image: Min.Bitmap Size=256, Bit Depth=8, Orig.Size=Off, Color=Monochrome
8150 Setup:
n on Configuration, System, Network:
n Host Name=DV8150DRE, IPAddr=accordingly
n Subnet Mask=accordingly, Gateway Addr=accordingly
n on Configuration, DICOM SCP, Communications:
n Port=5040, Association Limit=12, Source Name=DICOM
n on Configuration, Destination:
n AE Title: Log.Name=DV8150
n Media Types: Media=35x43cm, 4438x5390, 5262, Any
n Media Types: Media=35x35cm, 4438x4414,4286, Any
n Media Types: Media=11x14in, 3440x4438, 4310, Any
n Formatting: Aspect Ratio Mix Page=On, Aspect Ratio Mix Row=On
n Formatting: Image Size Mix in Std Fmt=On, Image Size Mix Row=On
n Formatting: DICOM Annotation Box=On, Req.Image Size=On
n Formatting: Req.Size Scale=On, Req.Size Mix Page=On
n Formatting: Req.Size Mix Row=On, Trim=On,
DICOM Network
Kodak MedView
Workstation
MedView Setup:
n on Print->Destinations->Add Menu:
n General: Class=DICOM Printer, Name=CMI1000
n DICOM: AE Title=CMI1000, Host Name=IP-Address of CMI1000
n DICOM: Port=5040, Destination=Processor, Enable Print Job Events=Off
n DICOM: Compose Sheet=Off, BFS Print Support=Off
n DICOM film: Magnif.=Cubic, Medium=Blue Film, Smoothing=2
n DICOM film: Config Info= LUT=0,9, Border=Black, MaxDensity=300
n DICOM media: 8INx10IN
n Layouts: 1,1; 1,2; 2,2; 2,3
n Image: Min.Bitmap Size=256, Bit Depth=8, Orig.Size=Off, Color=Color
CMI-1000 Setup:
at Local Panel, under Media, set A4 or Letter ie what inside Paper Tray
(CMI-1000 sw considers only this field and uses it as A4 or Letter (Always=Y):
at Local Panel, under Menu, Imager Setup:
n Network Setup:
n IPAddr=accordingly, Subnet Mask=accordingly, Gateway=accordingly
n under More Settings: DICOM Port=5040
n Edit Host Name/AE Title=CMI1000
n Modality (SCU) Config (or after modality recognition):
n Select Modality=accordingly, Modality Config.Assistant=Yes, Reset Config=No
n Note: Color IQ settings used when images sent with Color DICOM SOP
n under Image Quality, Color Image Quality: (no need to adjust, leave defaults)
n Match Monitor Colors=default ie sRGB Color Space Profile.icm
n Adjust Color Tones=default ie Default_Contrast_100.icm
n Note: Grayscale IQ settings used when images sent with Grayscale DICOM SOP:
n under Image Quality, Grayscale Image Quality:
n Contrast=9 (Always=Y), TFT Set (From list)=Pmsv3k.w87 (Always=Y)
n Wet Contrast=0 (Always=N), Curve Shape=429 (Always=N)
1
setup valid also for Kodak PACS LINK 25 PRINT SERVER.
iew
00 DryV
3M 87
Fiber Cable
iew
00 DryV
3M 87
Fiber Cable
DICOM Network
RS422
COPCIL Board 9-pole Plug
Copper Cable Control 9-pin
Kodak QCW Workstation
Data 37-pin
9410 Setup:
on Device Setup, LOCAL PRINTERS:
n Printer=8100, Model=8100 4096 pxls/line, Output=Copper
n Baud=1200, Parity=Even, Data=8, Stop=1, Command Set=952
n Pixel=12, Header/Line, Timeout=60, Transfer Rate=1 MHz
n Film Mismatch=Print Always, Interpolation Type=831
n Interp Num=5, Max.Density=300, Contrast=6, Border Density=0
n TFT/ULUT Emulation=On, Installed TFT/ULUT=Ver693c0.w87
on Device Setup, SCP PRINTERS, Current Providers:
n Printer=8100, AE Title=9410, Port=1024, Max Associations=5
on Device Setup, SCP PRINTERS, Registered Users:
n SCU AETitle=accordingly, SCU IPAddr=accordingly
n SCP=8100, Copies=1, Contrast Table=2, TFT/ULUT=Wrkstn2a.w87
n Max.Density=300, Border Density=0, Mag.Type=8, Smoothing=5
n Polarity=1, Orientation=1, Set Req.Image Size=No, Priority=Low
n Interceptor=Yes, N-Event-Print Job=No, N-Event Printer=No
n Trim=No, Attribute Warning=No
n Contrast Test Mode=No, Contrast Test Mode Density=0
DICOM Network
Data 37 pin
Requirements: QCW v5.0, 9410 v1.6, 8300 v4.9.1, 8300 LUT v3.0.3B
9410 Setup:
n on Device Setup, LOCAL PRINTERS:
n Printer=8300, Model=8300 Copper, Output=Copper
n Command Set=952, Baud=1200, Data=8, Stop=1, Parity=Even
n Pixel=8, Header/Line, Timeout=60, Transfer Rate=1 MHz
n Film Mismatch=Print Always, Interpolation Type=831
n Interp Num=0, Max.Density=300, Contrast=6, Border Density=0
n TFT/ULUT Emulation=On, Installed TFT/ULUT= upmsv3k.w8u
n on Device Setup, SCP PRINTERS, Current Providers:
n Printer=8300, AE Title=9410, Port=1024, Max Associations=5
n on Device Setup, SCP PRINTERS, Registered Users:
n SCU AETitle=accordingly, SCU IPAddr=accordingly
n SCP=8300, Copies=1, Contrast Table=1, TFT/ULUT=wrkstn83a.w8u
n Max.Density=300, Border Density=0, Mag.Type=8, Smoothing=3
n Polarity=1, Orientation=1, Set Req.Image Size=No, Priority=Low
n Interceptor=Yes, N-Event-Print Job=No, N-Event Printer=No
n Trim=No, Attribute Warning=No
n Contrast Test Mode=No, Contrast Test Mode Density=0
8300 Setup:
n on Operator Menu set: D=16, C=6, Sharp/Smooth=0 i.e., Auto
n on Operator Menu set: Film Layout: 1 on 1=Portrait
n on Service Menu set: Ratio=1.00, Serial=1200,8,1,Even,Comma,3M, Memory=16
n on Service Menu set: Digital Interface: Parity=Even, Modality Group=1
DICOM Network
iew
00 DryV
3M 87
Fiber Cable
MIM200 Setup:
n on Configure, Network:
n Node Name=MIM, IPAddr=accordingly
n Subnet Mask=accordingly, Gateway Addr=accordingly
n on Configure, Input, Network, Add:
n Protocol=DICOM 3.0, Log.Name=DICOM, Type/Com=Keypad/COM9
n on Configure, Destination, Add, Print, Direct, Qualified, 8700, Set:
n General: Log.Name=8700
n General: Database Name=8700, Model=8700, Memory=32
n Media Info: Media=35x43cm, 4096x5223, 5133, Blue
n Output Params: Cmd=SuperSet,Baud=19200,Data=8,Stop=1,Parity=None
n Output Params: Pixel=12, Header/Line, Transfer=2000 KHz, Acq=60
n Supported Item: Collation=On, Text=On, Tonescaling=On, Rotation=On
n Interpolation: NoMag=On, Bilin=On, Repl=On,Cubic Spline=On
n Format Types: Custom=On, Slide=On, Row Symmetric=On
n Format Types: 1, 2, 4, 6, 8, 9, 12, 15, 16, 20, 24, 30, 35=On
n Formatting: Aspect Ratio Mix on Page=On, Image Size Mix in Std Fmt=On
n Formatting: DICOM Annotation Box=On, Req.Size Scale=On
n Formatting: Req.Size Mix in Row=On, Trim=On
n Formatting: Aspect Ratio Mix in Row=On, Image Size Mix in Row=On
DICOM Network
iew
00 DryV
3M 87
Fiber Cable
MIM200 Setup:
n on Configure, Network:
n Node Name=MIM, IPAddr=accordingly
n Subnet Mask=accordingly, Gateway Addr=accordingly
n on Configure, Input, Network, Add:
n Protocol=DICOM 3.0, Log.Name=DICOM, Type/Com=Keypad/COM9
n on Configure, Destination, Add, Print, Direct, Qualified, 8500, Set:
n General: Log.Name=8500
n General: Database Name=8500, Model=8500, Memory=32
n Media Info: Media=11x14in, 3388x4283, 4193, Blue
n Output Params: Cmd=SuperSet,Baud=19200,Data=8,Stop=1,Parity=None
n Output Params: Pixel=12, Header/Line, Transfer=2000 KHz, Acq=60
n Supported Item: Collation=On, Text=On, Tonescaling=On, Rotation=On
n Interpolation: NoMag=On, Bilin=On, Repl=On,Cubic Spline=On
n Format Types: Custom=On, Slide=On, Row Symmetric=On
n Format Types: 1, 2, 4, 6, 8, 9, 12, 15, 16, 20, 24, 30, 35=On
n Formatting: Aspect Ratio Mix on Page=On, Image Size Mix in Std Fmt=On
n Formatting: DICOM Annotation Box=On, Req.Size Scale=On
n Formatting: Req.Size Mix in Row=On, Trim=On
n Formatting: Aspect Ratio Mix in Row=On, Image Size Mix in Row=On
DICOM Network
RS422
COPCIL Board 9-pole Plug
Copper Cable Control 9-pin
Kodak QCW Workstation
Data 37-pin
MIM200 Setup:
n on Configure, Network:
n Node Name=MIM, IPAddr=accordingly
n Subnet Mask=accordingly, Gateway Addr=accordingly
n on Configure, Input, Network, Add:
n Protocol=DICOM 3.0, Log.Name=DICOM, Type/Com=Keypad/COM9
n on Configure, Destination, Add, Print, Direct, Qualified, 8100, Set:
n General: Log.Name=8100
n General: Database Name=8100, Model=8100, Memory=32
n Media Info: Media=35x43cm, 4096x5223, 5133, Blue
n Output Params: Cmd Set=952, Baud=1200, Data=8, Stop=1, Parity=Even
n Output Params: Pixel=12, Header/Line, Transfer=1000 KHz, Acquire=60
n Supported Item: Collation=On, Text=On, Tonescaling=On, Rotation=On
n Interpolation: NoMag=On, Bilin=On, Repl=On,Cubic Spline=On
n Format Types: Custom=On, Slide=On, Row Symmetric=On
n Format Types: 1, 2, 4, 6, 8, 9, 12, 15, 16, 20, 24, 30, 35=On
n Formatting: Aspect Ratio Mix on Page=On, Image Size Mix in Std Fmt=On
n Formatting: DICOM Annotation Box=On, Req.Size Scale=On
n Formatting: Req.Size Mix in Row=On, Trim=On
n Formatting: Aspect Ratio Mix in Row=On, Image Size Mix in Row=On
n Formatting: Req.Image Size=On, Req.Size Mix on Page=On
n Formatting: True Landscape=On
n Formatting: Max Img per Band=20, Max Band per Page=20, Max Img Col=0
n Formatting: Max Img Row=0, Min Horiz Sep=2, Min Vert Sep=2
n Formatting: Trim Width Enabled=2, Trim Width Disabled=0
n Formatting: Pixel Pitch=12.8205
n Image Processing: Grayscale=On, Minify=On, Max Image Dmax=3.1
n M952 Usage: Min H/V Mag=1, Max H/V Mag=64, Min Dmax 952=1.7
n on Configure, SCP Services, select the specific modality, Modify:
n PLUT=N, ToneScaling=PerceptionLUT (Always=Y)
n TFT/ULUT=Wrkstn2a.w87 (Always=Y), Contrast (dry)=2 (Always=N)
n Image Dmin=0.00 (Always=N), Image Dmax=3.00 (Always=N)
n NeventReports=Off (Always=Y), Warning Status=On
n Print Date=Off, Print Time=Off, Page Number=Off, Hosp.Name=Off
n Modality ID=Off, Annotation Override=Off (Always=N)
n Print Priority=Normal (Always=N), Image Polarity=Normal (Always=N)
n Smoothing Type=5 (Always=N)
n Border=Black (Always=N), Film Base=Blue Film (Always=N)
n Film Size=14INx17IN (Always=N), Negotiate Color Print=Off
DICOM Network
Control 9 pin
Kodak QCW Workstation COPCIL board
Copper Cable
Data 37 pin
Requirements: QCW v5.0, MIM200 v6.1, 8300 v4.9.1, 8300 LUT v3.0.3B
Note: This setup is basically also valid for 25 PS computer
MIM200 Setup:
n on Configure, Network:
n Node Name=MIM, IPAddr=accordingly
n Subnet Mask=accordingly, Gateway Addr=accordingly
n on Configure, Input, Network, Add:
n Protocol=DICOM 3.0, Log.Name=DICOM, Type/Com=Keypad/COM9
n on Configure, Destination, Add, Print, Direct, Qualified, 8300, Set:
n General: Log.Name=8300
n General: Database Name=8300, Model=8300, Memory=32
n Media Info: Media=8x10in, 2256x2676, 2596, Blue
n Output Params: Cmd Set=952, Baud=1200, Data=8, Stop=1, Parity=Even
n Output Params: Pixel=8, Header/Line, Transfer=2000 KHz, Acquire=60
n Supported Item: Collation=On, Text=On, Tonescaling=On, Rotation=On
n Interpolation: NoMag=On, Bilin=On, Repl=On,Cubic Spline=On
n Format Types: Custom=On, Slide=On, Row Symmetric=On, SuperSlide=On
n Format Types: 1, 2, 4, 6, 8, 9, 12, 15, 16, 20, 24, 30, 35=On
n Formatting: Aspect Ratio Mix on Page=On, Image Size Mix in Std Fmt=On
n Formatting: DICOM Annotation Box=On, Req.Size Scale=On
n Formatting: Req.Size Mix in Row=On, Trim=On
n Formatting: Aspect Ratio Mix in Row=On, Image Size Mix in Row=On
n Formatting: Req.Image Size=On, Req.Size Mix on Page=On
n Formatting: True Landscape=On
n Formatting: Max Img per Band=20, Max Band per Page=20, Max Img Col=0
n Formatting: Max Img Row=0, Min Horiz Sep=2, Min Vert Sep=2
n Formatting: Trim Width Enabled=2, Trim Width Disabled=0
n Formatting: Pixel Pitch=11.811
n Image Processing: Grayscale=On, Minify=On, Max Image Dmax=3
n M952 Usage: Min H/V Mag=1, Max H/V Mag=16, Min Dmax 952=1.5
n on Configure, SCP Services, select the specific modality, Modify:
n PLUT=N, ToneScaling=PerceptionLUT (Always=Y)
n TFT/ULUT=wkstn83a.w8u (Always=Y), Contrast (dry)=1 (Always=N)
n Image Dmin=0.00 (Always=N), Image Dmax=3.00 (Always=N)
n NeventReports=Off (Always=Y), Warning Status=On
n Print Date=Off, Print Time=Off, Page Number=Off, Hosp.Name=Off
n Modality ID=Off, Annotation Override=Off (Always=N)
n Print Priority=Normal (Always=N), Image Polarity=Normal (Always=N)
n Smoothing Type=3 (Always=N)
n Border=Black (Always=N), Film Base=Blue Film (Always=N)
n Film Size=8INx10IN (Always=N), Negotiate Color Print=Off
8300 Setup:
n on Operator Menu set: D=16, C=6, Sharp/Smooth=0 i.e., Auto
n on Operator Menu set: Film Layout: 1 on 1=Portrait
n on Service Menu set: Ratio=1.00, Serial=1200,8,1,Even,Comma,3M, Memory=16
n on Service Menu set: Digital Interface: Parity=Even, Modality Group=1
DICOM Network
MIM200 Setup:
n on Configure, Network:
n Node Name=MIM, IPAddr=accordingly
n Subnet Mask=accordingly, Gateway Addr=accordingly
n on Configure, Input, Network, Add:
n Protocol=DICOM 3.0, Log.Name=DICOM, Type/Com=Keypad/COM9
n on Configure, Destination, Add, Print, Direct, Qualified, 8200, Set:
n General: Log.Name=8200, IPAddr=100.100.100.40,
n General: Database Name=8200, Model=8200, Memory=32
n Media Info: Media=35x43cm, 4361x5223, 5133, Any (Blue,Clear)
n Media Info: Media=35x35cm, 4361x4247, 4157, Any (Blue,Clear)
n Media Info: Media=11x14in, 3272x4361, 4271, Any (Blue,Clear)
n Supported Item: Collation=On, Common Text=On, Tonescaling=On
n Supported Item: Remote Image Deletion=On, Rotation=On
n Interpolation: No Magnification=On, Bilin=On, Repl=On
n Interpolation: Cubic Spline=On, Cubic Convolution 2=On
n Format Types: Custom=On, Row Symmetric=On
n Format Types: 1, 2, 4, 6, 8, 9, 12, 15, 16, 20, 24, 30, 35=On
n Formatting: Aspect Ratio Mix on Page=On, Image Size Mix in Std Fmt=On
n Formatting: DICOM Annotation Box=On, Req.Size Scale=On
n Formatting: Req.Size Mix in Row=On, Trim=On
n Formatting: Aspect Ratio Mix in Row=On, Image Size Mix in Row=On
n Formatting: Req.Image Size=On, Req.Size Mix on Page=On
DICOM Network
Kodak
QCW Workstation
8900 Setup:
n on Configuration, System, Network:
n Host Name=DV8900, IPAddr=accordingly
n Subnet Mask=accordingly, Gateway Addr=accordingly
n on Configuration, DICOM SCP, Communications:
n Port=5040, Association Limit=12, Source Name=DICOM
n on Configuration, Destination:
n General: Log.Name=8900
n Media Types: Media=35x43cm, 9100x11037, 10781, Any
n Media Types: Media=35x35cm,9100x9087, 8831, Any
n Media Types: Media=11x14in, 7137x9100, 8844, Any
n Media Types: Media=10x12in, 6490x7767, 7511, Any
n Media Types: Media=8x10in, 5167x6490, 6234, Any
n Formatting: Aspect Ratio Mix Page=On, Aspect Ratio Mix Row=On
n Formatting: Image Size Mix in Std Fmt=On, Image Size Mix Row=On
n Formatting: DICOM Annotation Box=On, Req.Image Size=On
n Formatting: Req.Size Scale=On, Req.Size Mix Page=On
n Formatting: Req.Size Mix Row=On, Trim=On,
n Formatting: True Landscape=On, Rotation=On
n Formatting: Minify/Crop=On, Tonescaling on Image Basis=On
n Formatting: Max Img Band=7, Max Band Page=7, Max Img Cols=0
n Formatting: Max Img Rows=0, Pixel Pitch=25.5910, Min Horiz Sep=4
n Formatting: Min Vert Sep=4, Trim Width Enabled=4
n Formatting: Trim Width Disabled=0, Maximum DMAX=3.30
n on Configuration, DICOM SCP, SCP Services, select specific modality, Modify:
DICOM Network
Kodak
QCW Workstation
8150 Setup:
n on Configuration, System, Network:
n Host Name=DV8150DRE, IPAddr=accordingly
n Subnet Mask=accordingly, Gateway Addr=accordingly
n on Configuration, DICOM SCP, Communications:
n Port=5040, Association Limit=12, Source Name=DICOM
n on Configuration, Destination:
n AE Title: Log.Name=DV8150
n Media Types: Media=35x43cm, 4438x5390, 5262, Any
n Media Types: Media=35x35cm, 4438x4414,4286, Any
n Media Types: Media=11x14in, 3440x4438, 4310, Any
n Formatting: Aspect Ratio Mix Page=On, Aspect Ratio Mix Row=On
n Formatting: Image Size Mix in Std Fmt=On, Image Size Mix Row=On
n Formatting: DICOM Annotation Box=On, Req.Image Size=On
n Formatting: Req.Size Scale=On, Req.Size Mix Page=On
n Formatting: Req.Size Mix Row=On, Trim=On,
n Formatting: True Landscape=On, Rotation=On
n Formatting: Minify/Crop=On, Tonescaling on Image Basis=On
n Formatting: Max Img Band=7, Max Band Page=7, Max Img Cols=0
n Formatting: Max Img Rows=0, Pixel Pitch=12.8000, Min Horiz Sep=2
n Formatting: Min Vert Sep=2, Trim Width Enabled=2
n Formatting: Trim Width Disabled=0, Maximum DMAX=3.10
n on Configuration, DICOM SCP, SCP Services, select specific modality, Modify:
n Negotiate Presentation LUT=No, Negotiate Color Print=No,
DICOM Network
Kodak
QCW Workstation
CMI-1000 Setup:
at Local Panel, under Media, set A4 or Letter ie what inside Paper Tray
(CMI-1000 sw considers only this field and uses it as A4 or Letter (Always=Y):
at Local Panel, under Menu, Imager Setup:
n Network Setup:
n IPAddr=accordingly, Subnet Mask=accordingly, Gateway=accordingly
n under More Settings: DICOM Port=5040
n Edit Host Name/AE Title=CMI1000
n Modality (SCU) Config (or after modality recognition):
n Select Modality=accordingly, Modality Config.Assistant=Yes, Reset Config=No
n Note: Color IQ settings used when images sent with Color DICOM SOP
n under Image Quality, Color Image Quality: (no need to adjust, leave defaults)
n Match Monitor Colors=default ie sRGB Color Space Profile.icm
n Adjust Color Tones=default ie Default_Contrast_100.icm
n Note: Grayscale IQ settings used when images sent with Grayscale DICOM SOP:
n under Image Quality, Grayscale Image Quality:
n Contrast=7 (Always=Y)
n TFT Set (From list)=Wrkstn2a.w87 (Always=Y)
n Wet Contrast=0 (Always=N), Curve Shape=429 (Always=N)
n under More Quality Settings:
n Tonescaling=Presentation LUT (Always=N),
n Image Dmax=220 (Always=N), Image Dmin=10 (Always=N)
n Smoothing=11 (Always=Y), Polarity=Positive (Always=N)
n Interpolation=CUBIC (Always=N), Trim=No (Always=N)
n Page Orientation=PORTRAIT (Always=N), Negotiate PLUT=No
n under Modality Defaults: