Professional Documents
Culture Documents
July, 2011
NEC Corporation
1. General
This document describes the interface specification between Emergency Agency and EWBS Server of digital terrestrial TV system in Chile.
MCT StartFlag AreaCode
HUB
HD/SD ENC1
Studio (Chile)
A/D
1seg ENC1
MUX
GPI
DTX
EditPC
Ethernet(100BASE-T)
HUB
2. Interface Specification
Interface specification for EWBS server describes below.
Description
Start flag of TMCC (ON/OFF) is sent to Multiplexer.
(2) Ethernet
- Emergency Information is received from Emergency Agency via Ethernet. - Below three services shall be executed by EWBS Server simultaneously. Service Name
1 2 3 Emergency Broadcast Area Code Emergency Character Super (via Ethernet) Area Code is sent to Multiplexer. (via Ethernet) Character information which is preset by Edit PC is sent to Multiplexer. Latin Character Code refers to Chapter 3.2.
Description
Start flag of TMCC (ON/OFF) is sent to Multiplexer.
Function
Status indication from Emergency Agency Preset of Character Super for GPI PID of HD, SD and 1seg. Service Priority set between GPI and Ethernet Set of the duration of health check
(1) In case of emergency condition, EWBS Server receives GPI (One of four contacts) from Emergency Agency. (2) Character Information is preset by the Edit terminal. (up to four kind of character info.) (3) EWBS Server sends Start Flag to Multiplexer by Ethernet. EWBS Server sends Character Super to Multiplexer by TS signal.
MCT
HUB
HD/SD ENC1
Studio (Chile)
A/D GPI Interface Four contacts
GPI
1seg ENC1
MUX
DTX
HUB
Emergency Agency is a server and EWB Server is a client. TCP/IP protocol is applied between these equipment. Emergency information and character information are sent from Emergency Agency to EWBS Server.
Description REQ_CSWE (Hexadecimal of character) 0: Emergency OFF, 1: Emergency ON Area Code (1area = 2byte) Several kinds of Area Code can be sent.
Remarks: - Assignment of Area Code shall be defined by the digital TV committee in Chile. - Maximum Area Code is 1022byte. (511 areas)
Description ANS_CSWE (Hexadecimal of character) Send of current condition 0: Fault, 1: Succeed Send of the Error Message at Faulty Condition
Description REQ_CMSP (Hexadecimal of character) 0:OFF, 1:ON Character Super (In case of ON)
Description ANS_CMSP (Hexadecimal of character) Send of Current Condition 0: Fault, 1: Succeed Send of the Error Message at Faulty Condition
Byte length 8 8
Description ANS_HEAL REQ_HEAL (same as the request command) Send the message
Specificationof Interface
HD/SD ENC1
HUB
Studio (Chile)
A/D
1seg ENC1
MUX
GPI
DTX
EditPC
Ethernet(100BASE-T)
Multiplexer is a server and EWB Server is a client. TCP/IP protocol is applied between these equipment. Start flag (Emergency broadcast ON/OFF) and Area code are sent from EWBS Server to Multiplexer.
3. Appendix
3.1 GPI specification 3.1.1 Circuit Diagram of GPI input
Circuit diagram of GPI input is shown below.
VCC Circuit
Photo-coupler
GPI Input
GND
GND
Pin No. 1
Description MAKE : Power ON condition (Normal) BREAK : Power off (Error), Both or one power supply is down. CPU board alarm
OUT2
MAKE : Alarm CPU board error or red indication of front panel. Application Error
OUT3
MAKE : Alarm Tally output of Character Super (1second pulse) MAKE : Make of 1 second after the output of character super. Ground Character Super-1 Character Super-2 Character Super-3 Character Super-4
4 5 6 7 8 9
Remarks: IN 1 to 4 are the pulse signal inputs. Duration of pulse is required minimum 100msec.
CR SO
1x DLE DC1 DC2 DC3 DC4 NAK SYN ETB CAN EM SUB ESC FS 2x 3x 4x 5x 6x 7x SP 0 @ P ` p ! 1 A Q a q " 2 B R b r # 3 C S c s $ 4 D T d t % 5 E U e u & 6 F V f v ' 7 G W g w ( 8 H X h x ) 9 I Y i y * : J Z j z + ; K [] k { , < L l |
GS RS US = M ] m } . > N ^ n ~ / ? O _ o DEL
8x PAD HOP BPH NBH IND NEL SSA ESA HTS HTJ VTS PLD PLU RI SS2 SS3 9x DCS PU1 PU2 STS CCH MW SPA EPA SOS SGCI SCI CSI ST OSC PM APC Ax NBSP Ax NBSP Bx Cx Dx Ex Fx