Professional Documents
Culture Documents
Copyright
This publication, including all photographs, illustrations and software, is protected under international copyright laws, with all rights reserved. Neither this manual, nor any of the material contained herein, may be reproduced without written consent of the author. Version 1.0C
Disclaimer
The information in this document is subject to change without notice. The manufacturer makes no representations or warranties with respect to the contents hereof and specifically disclaims any implied warranties of merchantability or fitness for any particular purpose. The manufacturer reserves the right to revise this publication and to make changes from time to time in the content hereof without obligation of the manufacturer to notify any person of such revision or changes.
Trademark Recognition
Microsoft, MS-DOS and Windows are registered trademarks of Microsoft Corp. MMX, Pentium, Pentium-II, Pentium-III, Celeron are registered trademarks of Intel Corporation. Other product names used in this manual are the properties of their respective owners and are acknowledged.
Shielded interconnect cables and a shielded AC power cable must be employed with this equipment to ensure compliance with the pertinent RF emission limits governing this device. Changes or modifications not expressly approved by the system s manufacturer could void the users authority to operate the equipment.
Preface
ii
Declaration of Conformity
This device complies with part 15 of the FCC rules. Operation is subject to the following conditions: This device may not cause harmful interference, and This device must accept any interference received, including interference that may cause undesired operation
Preface
iii
TABLE OF CONTENTS
Preface Chapter 1 i 1
Chapter 2
Installing the Motherboard 7 Safety Precautions...........................................................................7 Choosing a Computer Case............................................................7 Installing the Motherboard in a Case...........................................7 Checking Jumper Settings..............................................................8
Setting Jumpers.......................................................................8 Checking Jumper Settings......................................................9 Jumper Settings..................................................................... 9
Installing Hardware........................................................................10
Installing the Processor........................................................10 Installing Memory Modules..................................................12 Expansion Slots.....................................................................15 Connecting Optional Devices ...............................................17 Installing a Hard Disk Drive/CD-ROM/SATA Hard Drive..19 Installing a Floppy Diskette Drive........................................20
Chapter 3
25
Using BIOS......................................................................................26
Standard CMOS Setup...........................................................27 Advanced Setup.....................................................................30 Advanced Chipset Setup........................................................32 Integrated Peripherals..........................................................33
iv
Power Management Setup..........................................................34 PCI/PnP Setup ...........................................................................36 PC Health Status........................................................................36 Frequency/Voltage Control ........................................................38 Load Default Settings.................................................................39 Supervisor Password.................................................................39 User Password...........................................................................40 Save & Exit Setup.......................................................................40 Exit Without Saving ...................................................................40 Updating the BIOS.....................................................................41
Chapter 4
43
Using the Motherboard Software 43 About the Software CD-ROM......................................................43 Auto-installing under Windows XP/Vista..................................43
Running Setup............................................................................44
Chapter 5
49
Setting Up NVIDIA RAID Configuration 49 Setting Up a Non-Bootable RAID Array......................................49 Setting Up a Bootable RAID Array..............................................51
To reach DDR2 800, please make sure that System Clock Mode in Frequency/Voltage Control should be selected to Unlinked manually since the Auto-run is DDR2 667.
Feature Processor
This motherboard uses an LGA775 type of Intel CoreTM 2 Duo that carries the following features: Accommodates Intel CoreTM 2 Duo processors Supports a system bus (FSB) of 1333/1066/800 MHz Supports Hyper-Threading technology CPU
Hyper-Threading technology enables the operating system into thinking its hooked up to two processors, allowing two threads to be run in parallel, both on separate logical processors within the same physical processor.
Chipset
The NVIDIA MCP73V is a single-chip with proven reliability and performance. Supports 33-bit addressing for access to 8 GB of system memory PCI Express 16-lane link interface for external graphics processors PCI v2.3 interface at 33 MHz Integrated SATA 3.0 Gb/s Host Controller USB 2.0 ports supported Fast ATA-133 IDE controller
Memory
DDR2 667/533 (over spec up to 800) DDR2 SDRAM with single channel supported Accommodates two unbuffered DIMMs Up to 2 GB per DIMM with maximum memory size up to 4 GB
Audio
The onboard Audio provides the following features: 5.1 Channel High Definition Audio Codec DACs support 96K/48K/44.1KHz sample rate Power support: Digital:3.3V; Analog: 5.0V WOWTM and Tru SurroundTM from SRS Provides single ended CD input with DRM solutions and legacy OSissues
Onboard LAN
The onboard LAN provides the following features: 10/100 full/half duplex operation Supports MII, and 7-wire SNI (Serial Network Interface) IEEE 802.3/802.3u compliant
Expansion Options
: The motherboard comes with the following expansion options: One PCI Express x16 for Graphics Interface One PCI Express x1 slot Two 32-bit PCI v2.3 compliant slots One IDE connector supporting up to two IDE devices One floppy disk drive interface Four 7-pin SATA connectors This motherboard supports Ultra DMA bus mastering with transfer rates of 133/ 100/66/33 Mb/s.
Integrated I/O
The motherboard has a full set of I/O ports and connectors: Two PS/2 ports for mouse and keyboard One serial port One VGA port Four USB ports One LAN port Audio jacks for microphone, line-in and line-out
BIOS Firmware
The motherboard uses AMI BIOS that enables users to configure many system features including the following: Power management Wake-up alarms CPU parameters CPU and memory timing The firmware can also be used to set parameters for different processor clock speeds. 1. Some hardware specifications and software items are subject to change without prior notice. 2. Due to chipset limitation, we recommend that motherboard be operated in the ambiance between 0 and 50C.
Motherboard Components
* stands for optional components. This concludes Chapter 1. The next chapter explains how to install the motherboard.
Memo
Setting Jumpers
Use the motherboard jumpers to set system configuration options. Jumpers with more than one pin are numbered. When setting the jumpers, ensure that the jumper caps are placed on the correct pins.
The illustrations show a 2-pin jumper. When the jumper cap is placed on both pins, the jumper is SHORT. If you remove the jumper cap, or place the jumper cap on just one pin, the jumper is OPEN.
SHORT
OPEN
Jumper Settings
Jumper Type Description Setting (default) 1-2: NORMAL 2-3: CLEAR Before clearing the CMOS, make sure to 1 turn the system off. CLR_CMOS 1 1-2: VCC 2-3: 5VSB USBPWR_R
USBPWR_R 3-pin
USBPWR_F 3-pin
1 USBPWR_F
1. To avoid the system instability after clearing CMOS, we recommend users to enter the main BIOS setting page to Load Default Settings and then Save & Exit Setup. 2. Make sure the power supply provides enough VCC5_DUAL voltage before selecting the VCC5_DUAL function. 3. It is required that users place the USBPWR_F & USBPWR_R cap onto 2-3 pin rather than 1-2 pin as default if you want to wake up the computer by USB/PS2 KB/Mouse.
10
Installing Hardware
Installing the Processor
Caution: When installing a CPU heatsink and cooling fan make sure that you DO NOT scratch the motherboard or any of the surface-mount resistors with the clip of the cooling fan. If the clip of the cooling fan scrapes across the motherboard, you may cause serious damage to the motherboard or its components. On most motherboards, there are small surface-mount resistors near the processor socket, which may be damaged if the cooling fan is carelessly installed. Avoid using cooling fans with sharp edges on the fan casing and the clips. Also, install the cooling fan in a well-lit work area so that you can clearly see the motherboard and processor socket.
11
G. Fasten the cooling fan supporting base onto the CPU socket on the motherboard. H. Make sure the CPU fan is plugged to the CPU fan connector. Please refer to the CPU cooling fan users manual for more detail installation procedure. 1. To achieve better airflow rates and heat dissipation, we suggest that you use a high quality fan with 3800 rpm at least. CPU fan and heatsink installation procedures may vary with the type of CPU fan/ heatsink supplied. The form and size of fan/heatsink may also vary. 2. DO NOT remove the CPU cap from the socket before installing a CPU. 3. Return Material Authorization (RMA) requests will be accepted only if the motherboard comes with the cap on the LGA775 socket.
12
You must install at least one module in any of the two slots. Each module can be installed with 2 GB of memory; the total memory capacity is 4 GB. Do not remove any memory module from its antistatic packaging until you are ready to install it on the motherboard. Handle the modules only by their edges. Do not touch the components or metal parts. Always wear a grounding strap when you handle the modules.
Installation Procedure
Refer to the following to install the memory modules. 1 2 3 This motherboard supports unbuffered DDR2 SDRAM only. Push the latches on each side of the DIMM slot down. Align the memory module with the slot. The DIMM slots are keyed with notches and the DIMMs are keyed with cutouts so that they can only be installed correctly. Check that the cutouts on the DIMM module edge connector match the notches in the DIMM slot. Install the DIMM module into the slot and press it firmly down until it seats correctly. The slot latches are levered upwards and latch on to the edges of the DIMM. Install any remaining DIMM modules.
4 5
13
Module Name
VC256MB533D2 4PB11D9CHM Japan E2508AA-T7F-E Hynix HY5PS121621 Nanya NT5TU32M16AG-37B 5PB42 D9DCD Elpida D5116AF-5C-E Elpida 8D22IB-ED Aeneon AET94F370 DS AET93F370 SS Samsung K4T51083QB-ZCD5 VS512MB533D2 64M8CEC Elpida 04180WB01 Hynix HY5PS12821 HY818T512800AF37 33346778 Hynix HYB18T512800AF37 HY5PS12821 Nanya NT5TU64M8AE-37B 5PB32 D9DCN Elpida E5108AG-5C-E 6AD11 D9GCT PC2-4200U-4444-10-B1 K4T51083QF-ZCD5 PC2-4200U-4444-12-DS K4T51083QC Samsung 8D22JB-KM Elpida E5108AB-5C-E Elpida E5108AB-5C-E A016E2864T2AG8AKT5H120001 HY818T512800AF37 33344539 KKEA88E4AAKG-37 U2S12D30TP-5C HYS64T325001HU-3-A HYB18T256 5NB31 D9DCG AD29608A88-3EG AU512E667C5KBGY VALUESELECT 32M8CEC 64M8CFE PS1000545 Corsair K4T5108QC 0547W64M8 PC5300 AL6E8E63B-6E1T 5LB31 D9DCL 04400WB01 R050008A TMM6208G8M30B SEL520ZCE6 K4T51083QC JetRam J12Q3AB-6 Elpida 1GB AM4B5708GEWS7E-0637F AM4B5708GQJS7E0631F AU01GE667C5KBGY HYB18T512800BF3S Aeneon AET93E30RB-0650 1GB PQI PQB2648D38R0648 1 GB AL6E8E63B-6E1T K4T51083QC U2S12030TP-6E TBF614-L93G LeadMax LD5PS1G831
256 MB
Nanya Ramaxel Ramaxel Twinmos Aeneon Corsair Corsair Elpida Hynix Infineon
Kingston Kingston Ramaxel Ramaxel Ramaxel Samsung Samsung Twinmos Twinmos Apacer GEIL
1 GB
Infineon Kingmax UMAX Infineon Ramxel A-DATA Apacer Corsair Corsair Corsair
256 MB
512 MB
DDR2 667
1 GB
2 GB
LeadMax
14
Type
Size
Vendor
APOGEE Apacer CORSAIR
Module Name
AU51082-800P505 AHU512E800C5K1C CM2X1024-6400PRO HYS64T64020HU-2.5-A HYB18T256 800AF25 AL6E8E63H-8E1 U538H8G09DHL U2S12D30TP-8E
DDR2 800
512 MB
15
PCIEX16 Slot
The PCI Express x16 slot is used to install an external PCI Express graphics card that is fully compliant to the PCI Express Base Specification revision 1.1. The PCI Express x1 slot is fully compliant to the PCI Express Base Specification revision 1.1 as well. This motherboard is equipped with two standard PCI slots. PCI stands for Peripheral Component Interconnect and is a bus standard for expansion cards, which for the most part, is a supplement of the older ISA bus standard. The PCI slots on this board are PCI v2.3 compliant.
PCIEX1 Slot
PCI1~2 Slots
Before installing an add-on card, check the documentation for the card carefully. If the card is not Plug and Play, you may have to manually configure the card before installation.
16
Follow these instructions to install an add-on card: 1 2 3 Remove a blanking plate from the system case corresponding to the slot you are going to use. Install the edge connector of the add-on card into the expansion slot. Ensure that the edge connector is correctly seated in the slot. Secure the metal bracket of the card to the system case with a screw.
For some add-on cards, for example graphics adapters and network adapters, you have to install drivers and software before you can begin using the add-on card.
17
1 3 5 7 9
2 4 6 8 10
1 3 5 7
2 4 6 -
1 2 3 4
18
1 2 3 4 5 6 7 8 9 10
Please make sure that the USB cable has the same pin assignment as indicated above. A different pin assignment may cause damage or system hang-up.
1 2 3 4
19
IDE devices enclose jumpers or switches used to set the IDE device as MASTER or SLAVE. Refer to the IDE device users manual. Installing two IDE devices on one cable, ensure that one device is set to MASTER and the other device is set to SLAVE. The documentation of your IDE device explains how to do this.
SATA cable
(optional)
(optional)
20
Refer to the illustration below for proper installation: 1 2 3 Attach either cable end to the connector on the motherboard. Attach the other cable end to the SATA hard drive. Attach the SATA power cable to the SATA hard drive and connect the other end to the power supply.
21
Use the upper PS/2 port to connect a PS/2 pointing device. Use the lower PS/2 port to connect a PS/2 keyboard. Use the COM port to connect serial devices such as mice or fax/modems. Connect your monitor to the VGA port. Use the USB ports to connect USB devices. Connect an RJ-45 jack to the LAN port to connect your computer to the Network. Use the three audio jacks to connect audio devices. The first jack is for stereo line-in signal. The second jack is for stero line-out signal. The third jack is for microphone.
Audio Ports
22
When installing 4-pin power cable, the latches of power cable and the ATX12V match perfectly.
23
1 2 3 4
Sense Control
Users please note that the fan connector supports the CPU cooling fan of 1.1A ~ 2.2A (26.4W max) at +12V.
1 2 3
Sense
1 2 3 4 5 6 7 8 9 10 11 12
13 14 15 16 17 18 19 20 21 22 23 24
1 2 3 4
24
1 2 3 4
Pin 1 3 5 7 9
Signal
Function
Pin 4 6 8
Signal
Function
HD_LED_P Hard disk LED (+) 2 HD_LED_N Hard disk LED (-) RST_SW_N Reset Switch (-) RST_SW_P RSVD Reset Switch (+) Reserved
FP PWR/SLP *MSG LED (+) FP PWR/SLP *MSG LED (-) PWR_SW_P Power Switch (+) PWR_SW_N Power Switch (-) No pin
10 Key
Reset Switch
Supporting the reset function requires connecting pin 5 and 7 to a momentarycontact switch that is normally open. When the switch is closed, the board resets and runs POST.
Power Switch
Supporting the power on/off function requires connecting pins 6 and 8 to a momentary-contact switch that is normally open. The switch should maintain contact for at least 50 ms to signal the power supply to switch on or off. The time requirement is due to internal de-bounce circuitry. After receiving a power on/off signal, at least two seconds elapses before the power supply recognizes another on/off signal. This concludes Chapter 2. The next chapter covers the BIOS.
25
The settings made in the Setup Utility affect how the computer performs. Before using the Setup Utility, ensure that you understand the Setup Utility options. This chapter provides explanations for Setup Utility options.
Using BIOS
26
Press the delete key to access the BIOS Setup Utility.
CMOS Setup Utility -- Copyright (C) 1985-2007, American Megatrends, Inc. Standard CMOS Setup Advanced Setup Advanced Chipset Setup Integrated Peripherals Power Management Setup PCI/PnP Setup PC Health Status Frequency/Voltage Control Load Default Settings Supervisor Password User Password Save & Exit Setup Exit Without Saving
: Move Enter : Select +/-/: Value F10: Save F1:General Help F9: Optimized Defaults
ESC: Exit
Using BIOS
When you start the Setup Utility, the main menu appears. The main menu of the Setup Utility displays a list of the options that are available. A highlight indicates which option is currently selected. Use the cursor arrow keys to move the highlight to other options. When an option is highlighted, execute the option by pressing <Enter>. Some options lead to pop-up dialog boxes that prompt you to verify that you wish to execute that option. Other options lead to dialog boxes that prompt you for information. Some options (marked with a triangle ) lead to submenus that enable you to change the values for the option. Use the cursor arrow keys to scroll through the items in the submenu. In this manual, default values are enclosed in parenthesis. Submenu items are denoted by a triangle . The default BIOS setting for this motherboard apply for most conditions with optimum performance. We do not suggest users change the default values in the BIOS setup and take no responsibility to any damage caused by changing the BIOS settings.
FUNCTION
Exits the current menu Scrolls through the items on a menu Modifies the selected fields values Select Loads an optimized setting for better performance Saves the current configuration and exits setup Displays a screen that describes all key functions
Using BIOS
27
For the purpose of better product maintenances, we reserve the right to change the BIOS items presented in the manual. The BIOS setup screens shown in this chapter are for reference only. Please visit our website for updated manual.
: Move Enter : Select +/-/: Value F10: Save ESC: Exit F1: General Help F9: Optimized Defaults
Date & Time The Date and Time items show the current date and time on the computer. If you are running a Windows OS, these items are automatically updated whenever you make changes to the Windows Date and Time Properties utility.
Using BIOS
28
Primary IDE Master/Slave, SATA 1~4 (Not Detected) Your computer has one IDE channel which can be installed with one or two devices (Master and Slave). In addition, this motherboard supports four SATA channels and each channel allows one SATA device to be installed. Use these items to configure each device on the IDE channel.
CMOS SETUP UTILITY Copyright (C) 1985-2007, American Megatrends, Inc. Primary IDE Master Primary IDE Master Device : Not Detected Auto Auto Auto Auto Auto Auto Enabled Select the type of device connected to the system. Help Item
Type LBA/Large Mode Block (Multi-Sector Transfer PIO Mode DMA Mode S.M.A.R.T 32Bit Data Transfer
: Move Enter : Select +/-/: Value F10: Save ESC: Exit F1: General Help F9: Optimized Defaults
Type (Auto) Use this item to configure the type of the IDE device that you specify. If the feature is enabled, it will enhance hard disk performance by reading or writing more data during each transfer. LBA/Large Mode (Auto) Use this item to set the LAB/Large mode to enhance hard disk performance by optimizing the area the hard disk is visited each time. Block (Multi-Sector Transfer) (Auto) If the feature is enabled, it will enhance hard disk performance by reading or writing more data during each transfer. PIO Mode (Auto) Use this item to set the PIO mode to enhance hard disk performance by optimizing the hard disk timing. DMA Mode (Auto) DMA capability allows user to improve the transfer-speed and data-integrity for compatible IDE devices. S.M.A.R.T. (Auto) The S.M.A.R.T. (Self-Monitoring, Analysis and Reporting Technology) system is a diagnostics technology that monitors and predicts device performance. S.M.A.R.T. software resides on both the disk drive and the host computer. 32Bit Data Transfer (Enabled) Use this item to set the onboard SATA-IDE channel to be disabled, IDE, or RAID. Press <Esc> to return to the Standard CMOS Setup page.
Using BIOS
29
IDE BusMaster (Enabled) This item enables or disables the DMA under DOS mode. We recommend you to leave this item at the default value. Drive A (1 ..44 MB 31/2) This item defines the characteristics of any diskette drive attached to the system. You can connect one or two diskette drives.
Using BIOS
30
Advanced Setup
This page sets up more advanced information about your system. Handle this page with caution. Any changes can affect the operation of your computer.
CMOS Setup Utility - Copyright (C) 1985-2007, American Megatrends, Inc. Advanced Setup Thermal Management TM Status Limit CPUID MaxVal Enhanced Halt (C1E) Intel XD Bit Intel EIST Intel Virtualization Technol Quick Power on Self Test Boot Up Numlock Status APIC Mode 1st Boot Device 2nd Boot Device 3rd Boot Device Removable Drives Boot Other Device BIOS Protect Enabled TM1/TM2 Disabled Enabled Disabled Enabled Enabled Enabled On Enabled Hard Drive CD/DVD 1st FLOPPY DRIVE Press Enter Yes Disabled Help Item SouthBrigde to K8(CPU) frequency selection by CPU capability
: Move Enter : Select +/-/: Value F10: Save ESC: Exit F1:General Help F9: Optimized Defaults
Thermal Management (Enabled) This item displays CPUs temperature and enables you to set a safe temperature to Prescott CPU. TM Status (TM1/TM2) This item displays CPU Monitor status. Limit CPUID MaxVal (Disabled) Use this item to enable or disable the Max CPU ID value limit. When suppports Prescott and LGA775 CPUs, enables this to prevent the system from rebooting when trying to install Windows NT 4.0. Enhanced Halt (C1E) (Enabled) This item enables or disables enhanced halt. Intel XD Bit (Disabled) This item enables or disables the Intel XD Bit technology. Intel EIST (Enabled) This item allows users to enable or disable the EIST (Enhanced Intel Speedstep Technology) function. This item shows only if the CPU supports EIST. Intel Virtulization Technol (Enabled) When enabled, a VMM can utilize the additional hardware capabilities provided by Vandor Pool Technology. Quick Power on Self Test (Enabled) Enable this item to shorten the power on testing (POST) and have your system start up faster. You might like to enable this item after you are confident that your system hardware is operating smoothly.
Using BIOS
31
Boot Up Numlock Status (On) This item defines if the keyboard Num Lock key is active when your system is started. APIC Mode (Enabled) This item allows you to enable or disable the APCI (Advanced Programmable Interrupt Controller) mode. APIC provides symmetric multi-processing (SMP) for systems, allowing support for up to 60 processors. 1st/2nd/3rd Boot Device (Hard Drive/CD/DVD/1st FLOPPY DRIVE) Use this item to determine the device order the computer used to look for an operating system to load at start-up time. The devices showed here will be different depending on the exact devices installed on your motherboard. Removable Drives (Press Enter) Scroll to this item and press <Enter> to view the following screen:
CMOS Setup Utility - Copyright (C) 1985-2007, American Megatrends, Inc. Removable Drives Removable Drives 1st Drive 1st FLOPPY DRIVE
Help Item Specifies the boot sequence from the available devices.
: Move Enter : Select +/-/: Value F10: Save ESC: Exit F1:General Help F9: Optimized Defaults
Press <Esc> to return to the Advanced setup page. Boot Other Device (Yes) When enabled, the system searches all other possible locations for an operating system if it fails to find one in the devices specified under the First, Second, and Third boot devices. BIOS Protect (Disabled) This item is set to enable or disable the BIOS Protect. Press <Esc> to return to the main menu setting page.
Using BIOS
32
: Move Enter : Select +/-/: Value F10: Save ESC: Exit F1:General Help F9: Optimized Defaults
Memory Timings (Auto) This item shows the current and target memory performance rates when the system is undertaking the best performance. Top of Memory under 4GB (3.25 GB) This item shows the top of memory under 4GB. Memory Remap Feature (Enabled) This item allows you to remap the overlapped PCI memory above the total physical memory if you have a 64 bit OS and 4 GB of RAM. Dual Monitor Function (Disabled) This item is a switch to turn on/off the Dual Monitor function. If it is enabled, please connect the system to two monitors for performing the Dual Monitor function; if disabled, this function will be turned off. VGA Share Memory Auto Detect (Auto) This item lets you allocate a portion of the main memory for the onboard VGA display application. Share Memory Value (128MB) This item displays the VGA Share Memory Value. Press <Esc> to return to the main menu setting page.
Using BIOS
33
Integrated Peripherals
This page sets up some parameters for peripheral devices connected to the system.
CMOS Setup Utility - Copyright (C) 1985-2007, American Megatrends, Inc. Integrated Peripherals Onboard IDE Controller OnChip S-ATA Controller SATA Mode Select Onboard AUDIO Function Onboard LAN Function Onboard LAN Boot ROM Serial Port1 Address Parallel Port Address Parallel Port Mode Parallel Port IRQ USB Controller Legacy USB Support Enabled Enabled SATA Mode Enabled Enabled Disabled 3F8/IRQ4 378 Normal IRQ7 Enabled Enabled Help Item Options SATA Mode RAID Mode AHCI Mode
: Move Enter : Select +/-/: Value F10: Save ESC: Exit F1:General Help F9: Optimized Defaults
OnBoard IDE Controller (Enabled) Use this item to enable or disable the onboard IDE interface. Onboard S-ATA Controller (Enabled) This item allows you to enable or disable the onboard SATA controller. SATA Mode select (SATA Mode) Use this item to select the mode of the Serial ATA. Onboard AUDIO Function (Enabled) Use this item to enable or disable the onboard audio device. OnBoard LAN Function (Enabled) Use this item to enable or disable the onboard LAN function. OnBoard LAN Boot ROM (Disabled) Use this item to enable or disable the booting from the onboard LAN or a network add-in card with a remote boot ROM installed. Serial Port1 Address (3F8/IRQ4) Use this item to enable or disable the onboard COM1/2 serial port, and to assign a port address. Parallel Port Address (378) Use this item to enable or disable the onboard Parallel port, and to assign a port address. Parallel Port Mode (Normal) Use this item to select the parallel port mode. You can select Normal (Standard Parallel Port), ECP (Extended Capabilities Port), EPP (Enhanced Parallel Port), or BPP (Bi-Directional Parallel Port).
Using BIOS
34
Parallel Port IRQ (IRQ7) Use this item to assign IRQ to the parallel port. USB Controller (Enabled) This item enables the USB controller. Leave this at the default Enabled if you want to connect USB devices to your computer. Legacy USB Support (Enabled) Use this item to enable or disable support for legacy USB devices. Setting to Auto allows the system to detect the presence of USB device at startup. If detected, the USB controller legacy mode is enabled. If no USB device is detected, the legacy USB support is disabled. Press <Esc> to return to the main menu setting page.
ACPI Suspend Type Soft-off by PWR-BTTN PWRON After PWR-Fail Resume By PCI/PCI-E/Lan PME Resume By USB (S3) Resume By PS2 KB (S3) Resume By PS2 MS (S3) Resume On Ring Resume on RTC Alarm
S3 (STR) Instant Off Power Off Disabled Disabled Disabled Disabled Disabled Disabled
Help Item Select the ACPI state used for System Suspend.
: Move Enter : Select +/-/: Value F10: Save F9: Optimized Defaults F1:General Help
ESC: Exit
ACPI Suspend Type (S3(STR)) Use this item to define how your system suspends. In the default, S3, the suspend mode is a suspend to RAM, i.e, the system shuts down with the exception of a refresh current to the system memory. Soft-Off By PWR-BTTN (Instant Off) Under ACPI (Advanced Configuration and Power management Interface) you can create a software power down. In a software power down, the system can be resumed by Wake Up Alarms. This item lets you install a software power down that is controlled by the power button on your system. If the item is set to Instant-Off, then the power button causes a software power down. If the item is set to Delay 4 Sec, then you have to hold the power button down for four seconds to cause a software power down.
Using BIOS
35
PWRON After PWR-Fail (Power Off) This item enables your computer to automatically restart or return to its operating status. Resume by PCI/PCI-E/Lan PME (Disabled) These items specify whether the system will be awakened from power saving modes when activity or input signal of the specified hardware peripheral or component is detected. Resume By USB (S3) (Disabled) This item allows you to enable/disable the USB device wakeup function from S3/S4 mode. Resume By PS2 KB (S3) (Disabled) This item enable or disable you to allow keyboard activity to awaken the system from power saving mode. Resume By PS2 MS (S3) (Disabled) This item enable or disable you to allow mouse activity to awaken the system from power saving mode. Resume On Ring (Disabled) The system can be turned off with a software command. If you enable this item, the system can automatically resume if there is an incoming call on the Modem. You must use an ATX power supply in order to use this feature. Resume on RTC Alarm (Disabled) The system can be turned off with a software command. If you enable this item, the system can automatically resume at a fixed time based on the systems RTC (realtime clock). Use the items below this one to set the date and time of the wake-up alarm. You must use an ATX power supply in order to use this feature.
Using BIOS
36
: Move Enter : Select +/-/: Value F10: Save ESC: Exit F1:General Help F9: Optimized Defaults
Init Display First (PCI) Use this item to select which graphics controller to use as the primary boot devices. Press <Esc> to return to the main menu setting page.
PC Health Status
On motherboards support hardware monitoring, this item lets you monitor the parameters for critical voltages, temperatures and fan speeds.
CMOS Setup Utility - Copyright (C) 1985-2005, American Megatrends, Inc. PC Health Status -=- System Hardware Monitor-=Smart Fan Function Shutdown Temperature System Temperature CPU Temperature CPU Fan Speed CPU Vcore VDIMM Help Item Press Enter Disabled :31C/87F :45C/159F :5625 RPM :1.256V :1.952V
: Move Enter : Select +/-/: Value F10: Save ESC: Exit F1:General Help F9: Optimized Defaults
Using BIOS
37
Smart Fan Function Scroll to this item and press <Enter> to view the following screen:
CMOS Setup Utility - Copyright (C) 1985-2007, American Megatrends, Inc. Smart Fan Function CPU SMART FAN Control TargetTemp Value Tolerance Value StartUp Value Stop Value StopTime Value Enabled 060 03 150 100 060 Help Item Options Disabled Enabled
: Move Enter : Select +/-/: Value F10: Save ESC: Exit F1:General Help F9: Optimized Defaults
CPU SMART FAN Control (Enabled) This item allows you to enable or disable the control of the CPU fan speed by changing the CPU temperature.
Shutdown Temperature (Disabled) This item nables you to set the maximum temperature the system can reach before powering down. System Component Characteristics These items display the monitoring of the overall inboard hardware health events, such as System & CPU temperature, CPU & DIMM voltage, CPU & system fan speed,...etc. System Temperature CPU Temperature CPU Fan Speed CPU Vcore VDIMM Press <Esc> to return to the main menu setting page.
Using BIOS
38
Frequency/Voltage Control
This page enables you to set the clock speed and system bus for your system. The clock speed and system bus are determined by the kind of processor you have installed in your system.
CMOS Setup Utility - Copyright (C) 1985-2007, American Megatrends, Inc. Frequency/Voltage Control Manufacturer: Intel Ratio Status: Unlocked (Min: 06, Max: 07) Ratio Actual Value: 7 Auto Detect DIMM/PCI CIK Enabled System Clock Mode Auto CPU BSEL Select Auto PCIE Spread Spectrum Disabled CPU Spread Spectrum Disabled DIMM Voltage Control 1.90V NB Voltage Control 1.375V Help item [Auto] Set FSB & Memory clock automatically. [Linked] Allows Memory and FSB to overclock proportionally. [Manual] Enter FSB and Memory clock manually.
: Move Enter : Select +/-/: Value F10: Save ESC: Exit F1:General Help F9: Optimized Defaults
Manufacturer (Intel) These items show the brand of the CPU installed in your system. Ratio Status/Ratio Actual Value (Unlocked/7) This item shows the locked/unlocked ratio status and the actual ratio of the CPU installed inyour system. Auto Detect DIMM/PCI Clk (Enabled) When this item is enabled, BIOS will disable the clock signal of free DIMM/PCI slots. Syetem Clock Mode (Auto) This item determines the current and target FSB and memory speed when the system is undertaking the best performance. CPU BSEL Select (Auto) This item is used to select the CPU BSEL. PCIE Spread Spectrum (Disabled) This item, when enabled, can significantly reduce the EMI (Electromagnetic Interference) generated by the PCIE. CPU Spread Spectrum (Disabled) If you enable spread spectrum, it can significantly reduce the EMI (Electro-Magnetic Interference) generated by the system. DIMM Voltage Control (1.90V) This item is used to control the voltage of the DIMM.
Using BIOS
39
NB Voltage Control (1.375V) Use this item to adjust the Northbridge voltage. Press <Esc> to return to the main menu setting page.
Supervisor Password
This page helps you install or change a password.
CMOS Setup Utility - Copyright (C) 1985-2007, American Megatrends, Inc. Supervisor Password Supervisor Password :Not Installed Press Enter Help item Install or Change the password.
: Move Enter : Select +/-/: Value F10: Save ESC: Exit F1:General Help F9: Optimized Defaults
Supervisor Password (Not Installed) This item indicates whether a supervisor password has been set. If the password has been installed, Installed displays. If not, Not Installed displays. Change Supervisor Password (Press Enter) You can select this option and press <Enter> to access the sub menu. You can use the sub menu to change the supervisor password. Press <Esc> to return to the main menu setting page.
Using BIOS
40
User Password
This page helps you install or change a password.
CMOS Setup Utility - Copyright (C) 1985-2007, American Megatrends, Inc. User Password User Password : Not Installed Help item
: Move Enter : Select +/-/: Value F10: Save ESC: Exit F1:General Help F9: Optimized Defaults
User Password (Not Installed) This item indicates whether a user password has been set. If the password has been installed, Installed displays. If not, Not Installed displays.
Using BIOS
41
3 4 5
This concludes Chapter 3. Refer to the next chapter for information on the software supplied with the motherboard.
Using BIOS
42
Memo
Using BIOS
43
If the opening screen does not appear; double-click the file setup.exe in the root directory.
44
Setup Tab Setup Click the Setup button to run the software installation program. Select from the menu which software you want to install.
Browse CD The Browse CD button is the standard Windows command that allows you to open Windows Explorer and show the contents of the support CD. Before installing the software from Windows Explorer, look for a file named README.TXT, INSTALL.TXT or something similar. This file may contain important information to help you install the software correctly. Some software is installed in separate folders for different operating systems, such as Windows XP/Vista. Always go to the correct folder for the kind of OS you are using. In install the software, execute a file named SETUP.EXE or INSTALL.EXE by double-clicking the file and then following the instructions on the screen. Exit The EXIT button closes the Auto Setup window.
Application Tab Lists the software utilities that are available on the CD. Read Me Tab Displays the path for all software and drivers available on the CD.
Running Setup
Follow these instructions to install device drivers and software for the motherboard:
1. Click Setup. The installation program begins:
The following screens are examples only. The screens and driver lists will be different according to the motherboard you are installing. The motherboard identification is located in the upper left-hand corner.
45
2.
3. 4.
Check the box next to the items you want to install. The default options are recommended. Click Next run the Installation Wizard. An item installation screen appears:
5.
1. Drivers and software are automatically installed in sequence. Follow the onscreen instructions, confirm commands and allow the computer to restart a few times to complete the installation. 2. During the Windows Vista Driver Auto Setup Procedure, users should use one of the following two methods to install the driver after the system restart.
46
47
2.
3.
4.
48
5. Disable User Account Control (UAC) to help protect your computer item and press OK, then press Restart Now. Then you can restart your computer and continue to install drivers without running blocked programs.
Manual Installation
Insert the CD in the CD-ROM drive and locate the PATH.DOC file in the root directory. This file contains the information needed to locate the drivers for your motherboard. Look for the chipset and motherboard model; then browse to the directory and path to begin installing the drivers. Most drivers have a setup program (SETUP.EXE) that automatically detects your operating system before installation. Other drivers have the setup program located in the operating system subfolder. If the driver you want to install does not have a setup program, browse to the operating system subfolder and locate the readme text file (README.TXT or README.DOC) for information on installing the driver or software for your operating system.
49
Figure 1.1
2
Use the arrow keys to select Integrated Peripherals (see Figure 1.1), then press Enter. The Integrated Peripherals window appears.
Figure 1.2
50
3 From the Integrated Peripherals Window, globally set SATA Mode select to RAID Mode (see Figure 1.2). Press F10 to save the configuration and exit (F10 is the navigation key to save the current configuration and exit setup in BIOS setting). The PC reboots.
Figure 1.3 2 3
Select the modules that you want to install. Make sure that the NVIDIA IDE Driver is selected. You must install the NVIDIA IDE driver in order to enable NVIDIA RAID. If you do not install the NVIDIA IDE driver, NVIDIA RAID will not be enabled. Click Next and then follow the instructions.After the installation is completed, be sure to reboot the PC. After the reboot, initialize the newly created array.
51
Figure 1.4
2
Use the arrow keys to select Integrated Peripherals (see Figure 1.4), then press Enter. The Integrated Peripherals screen (or a screen similar to it) appears.
Figure 1.5 3
From the Integrated Peripherals Window, globally set SATA Mode select to RAID Mode (see Figure 1.5).
52
4 Press F10 to save the configuration and exit. The PC reboots. 5 Enter the RAID BIOS Setup by pressing F10 when prompted, and proceed to set up the NVIDIA RAID BIOS as described in the next section.
53
The NVIDIA RAID UtilityDefine a New Array screen appears (Figure 1.7).
Figure 1.7
MediaShield BIOS
By default, RAID Mode is set to Mirroring and Striping Block is set to Optimal.
54
Figure 1.8 illustrates the Define a New Array screen after one disk have been assigned as RAID 0 array disk.
Figure 1.8
Figure 1.9
55
2 Press Y to clear the disk data. The Array List screen appears, where you can review the RAID arrays that you have set up.
Figure 1.10
3 4
Use the arrow keys to select the array that you want to set up, then press B to specify the array as bootable. Press Enter to view and verify details. The Array Detail screen shows various information about the array that you selected, such as Striping Block used, RAID Mode, Striping Width, Disk Model Name, and disk capacity.
5 6 7
If you want to mark this disk as empty and wipe out all its contents, press C. At the prompt, press Y to wipe out all the data, otherwise press N. Press Enter again to go back to the previous screen and then press F10 to exit the RAID setup.
56
Figure 1.11 4
Specify the NVIDIA drivers. a Insert the floppy that has the RAID driver, press S, then press Enter.
Figure 1.12
57
b c d Select NVIDIA RAID CLASS DRIVER (required) and then press Enter. Press S again at the Specify Devices screen, then press Enter. Select NVIDIA NForce Storage Controller (required) and then press Enter.
Figure 1.13 5
Press Enter to continue with Windows XP Installation. Be sure to leave the floppy disk inserted in the floppy drive until the blue screen portion of Windows XP installation is completed, then take out the floppy.
Follow the instructions on how to install Windows XP. After Windows XP is completely installed, it is recommended that you install the ForceWare software in order to access the MediaShield RAID Management tool.
Note:
Each time you add a new hard drive to a RAID array, the RAID driver will have to be installed under Windows once for that hard drive. After that, the driver will not have to be installed.
58
Memo