Professional Documents
Culture Documents
PQ1CZ21H2ZxH
Features
1.Maximum switching current: 1.5A 2.Low dissipation current at OFF-state(Iqs:Max.1mA) 3.Built-in oscillation circuit (Oscillation frequency:TYP.100kHz) 4.Built-in overheat, overcurrent protection functions 5.Variable output voltage (Output variable range: Vref to 35V/Vref to 30V) [Possible to select step-down output/inversing output according to external connection circuit] 6.P Q 1CZ21H2ZZH: Sleeve-packaged product P Q 1CZ21H2ZPH: Tape-packaged product 7.RoHS directive compliant
Outline Dimensions
(Unit:mm)
6.6MAX.
5.20.5
3
2.30.5 (0.5)
Epoxy resin
9.7MAX.
5.50.5
1CZ21H H
2.5MIN.
(1.7)
(0 to 0.25)
) : Typical dimensions
Product mass:(0.3g)
VIN VOUT COM(Connected with heat sink) Oadj ON/OFF control
Applications
1.Facsimiles 2.Printers 3.Switching power supplies
*1 Voltage between VIN terminal and COM terminal *2 Voltage between VOUT terminal and COM terminal *3 Voltage between ON/OFF control and COM terminal *4 PD:With infinite heat sink *5 There is case that over heat protection function operates at the temperature Tj=125C to 150C, so this item cannot be used in this temperature range.
Notice The content of data sheet is subject to change without prior notice. In the absence of confirmation by device specification sheets, SHARP takes no responsibility for any defects that may occur in equipment using any SHARP devices shown in catalogs, data books, etc. Contact SHARP in order to obtain the latest device specification sheets before using any SHARP device.
(1.9)
PQ1CZ21H2ZxH
Electrical Characteristics
Parameter Output saturation voltage Reference voltage Reference voltage temperature fluctuation Load regulation Line regulation Efficiency Oscillation frequency Oscillation frequency temperature fluctuation Overcurrent detecting level ON threshold voltage ON-state current for control OFF-state current for control Stand-by current Output OFF-state dissipation current
(Unless otherwise specified,condition shall be VIN=12V,IO=0.2A,VO=5V,ON-OFF terminal=2.7V,Ta=25) Symbol VSAT Vref |RegL| |RegI| fO IL VTH(ON) IC(ON) IC(OFF) ISD IQS Conditions ISW=1A Tj=0 to 125 IO=0.2 to 1A VIN=8 to 35V IO=1A Tj=0 to 125 Switching current peak terminal=0V, terminal terminal=2.7V terminal=0.4V VIN=40V, terminal=0V VIN=40V, terminal=3V MIN. 1.235 80 1.55 0.8 TYP. 0.9 1.26 0.5 0.1 0.5 82 100 3 2 1.5 8 MAX. 1.5 1.285 1.5 2.5 120 2.6 2 200 2 1 12 mA Unit V V % % % % kHz % A V
IO
VO
A
Iqs
PQ1CZ21H2ZxH
R2
+ VIN
CIN
IC(ON) IC (OF F )
D
R1
CO
Load
470 F
6 5 4 3 2 1
0 -40 -25
PQ1CZ21H2ZxH
Tj=25C
1 0.8 0.6 0.4 0.2 0 0
90
Efficiency (%)
80
VO=5V, IO=1A
70
VO=5V, IO=0.2A
60 50 0
10
20
30
40
0.5
1.5
VIN=12V VO=5V
-1
-2 -50
-25
25
50
75
100
125
0.5
0.2
0.4
0.6
0.8
1.2
VIN=12V VO=5V
0.5
-25
25
50
75
100
125
PQ1CZ21H2ZxH
VIN=12V
1.5
0.5
0 -50
-25
25
50
75
100
125
Tj=25C VO=5V
9
IO=1A
8
IO=0.2A
No load
6 5 0
10
20
30
40
1.5
0.5
0 -40
PQ1CZ21H2ZxH
Voltage regulator + _
5
PWM COMP.
F/F
Q S
OSC.
PQ1CZ21H2ZxH
L 210H
VO 5V
R2 3k + CO 470F R1 1k
Load
PQ1CZ21H2ZxH
L 130H
R2 3k +
Load
D R1 1k
CO 2200F
VO
ON/OFF control signal
-5V
In case that polarity is reverse, depending on the conditions,there is cases that output voltage can not gain, please use this device after confirming the output voltage at the actual conditions.