Professional Documents
Culture Documents
D D D D D
Low Power Consumption Wide Common-Mode and Differential Voltage Ranges Low Input Bias and Offset Currents Output Short-Circuit Protection Low Total Harmonic Distortion 0.003% Typ
D D D D D D
Low Noise Vn = 18 nV/Hz Typ at f = 1 kHz High Input Impedance . . . JFET Input Stage Internal Frequency Compensation Latch-Up-Free Operation High Slew Rate . . . 13 V/ s Typ Common-Mode Input Voltage Range Includes VCC +
description
The JFET-input operational amplifiers in the TL07_ series are designed as low-noise versions of the TL08_ series amplifiers with low input bias and offset currents and fast slew rate. The low harmonic distortion and low noise make the TL07_ series ideally suited for high-fidelity and audio preamplifier applications. Each amplifier features JFET inputs (for high input impedance) coupled with bipolar output stages integrated on a single monolithic chip. The C-suffix devices are characterized for operation from 0C to 70C. The I-suffix devices are characterized for operation from 40C to 85C. The M-suffix devices are characterized for operation over the full military temperature range of 55C to 125C.
AVAILABLE OPTIONS PACKAGE TA VIOmax AT 25C 10 mV 6 mV 3 mV 0C to 70C 10 mV 6 mV 3 mV 10 mV 6 mV 3 mV 40C to 85C 55C to 125 C 125C 6 mV 6 mV 6 mV 9 mV SMALL OUTLINE (D) TL071CD TL071ACD TL071BCD TL072CD TL072ACD TL072BCD TL074CD TL074ACD TL074BCD TL071ID TL072ID TL074ID CHIP CARRIER (FK) CERAMIC DIP (J) CERAMIC DIP (JG) PLASTIC DIP (N) PLASTIC DIP (P) TL071CP TL071ACP TL071BCP TL072CP TL072ACP TL072BCP TL071IP TL072IP TL072MP TSSOP PACKAGE (PW) TL071CPWLE TL072CPWLE TL074CPWLE FLAT PACKAGE (W)
TL074MJ
TL071MJG TL072MJG
TL074MW
The D package is available taped and reeled. Add the suffix R to the device type (e.g., TL071CDR). The PW package is only available left-ended taped and reeled (e.g., TL072CPWLE).
Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet.
Copyright 1996, Texas Instruments Incorporated
PRODUCTION DATA information is current as of publication date. Products conform to specifications per the terms of Texas Instruments standard warranty. Production processing does not necessarily include testing of all parameters.
TL071, TL071A, TL071B, TL072 TL072A, TL072B, TL074, TL074A, TL074B LOW-NOISE JFET-INPUT OPERATIONAL AMPLIFIERS
SLOS080D SEPTEMBER 1978 REVISED AUGUST 1996
OFFSET N1 IN IN + VCC
1 2 3 4
8 7 6 5
NC VCC +
OUT OFFSET N2
1 2 3 4
8 7 6 5
1 2 3 4 5 6 7
14 13 12 11 10 9 8
NC OFFSET N1 NC NC NC
NC 1OUT NC VCC + NC
NC VCC NC 2IN+ NC
NC No internal connection
symbols
TL071 OFFSET N1 IN + IN OFFSET N2 + OUT IN IN + TL072 (each amplifier) TL074 (each amplifier) + OUT
NC VCC NC OFFSET N2 NC
NC IN NC IN + NC
4 5 6 7 8
3 2 1 20 19 18 17 16 15 14 9 10 11 12 13
NC VCC + NC OUT NC
NC 1IN NC 1IN + NC
4 5 6 7 8
3 2 1 20 19 18 17 16 15 14 9 10 11 12 13
NC 2OUT NC 2IN NC
4 5 6 7 8
3 2 1 20 19 18 17 16 15 14 9 10 11 12 13
TL071, TL071A, TL071B, TL072 TL072A, TL072B, TL074, TL074A, TL074B LOW-NOISE JFET-INPUT OPERATIONAL AMPLIFIERS
SLOS080D SEPTEMBER 1978 REVISED AUGUST 1996
IN + IN 64
128 OUT 64
C1 18 pF
VCC
TL071 Only
OFFSET NULL (N2) COMPONENT COUNT TL071 11 14 2 1 1 1 TL072 22 28 4 2 2 2 TL074 44 56 6 4 4 4
1080
1080
TL071, TL071A, TL071B, TL072 TL072A, TL072B, TL074, TL074A, TL074B LOW-NOISE JFET-INPUT OPERATIONAL AMPLIFIERS
SLOS080D SEPTEMBER 1978 REVISED AUGUST 1996
absolute maximum ratings over operating free-air temperature range (unless otherwise noted)
Supply voltage, VCC + (see Note 1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18 V Supply voltage, VCC (see Note 1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18 V Differential input voltage, VID (see Note 2) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30 V Input voltage, VI (see Notes 1 and 3) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15 V Duration of output short circuit (see Note 4) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . unlimited Continuous total power dissipation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . See Dissipation Rating Table Operating free-air temperature range, TA: C suffix . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0C to 70C I suffix . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40C to 85C M suffix . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55C to 125C Storage temperature range . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 65C to 150C Case temperature for 60 seconds: FK package . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 260C Lead temperature 1,6 mm (1/16 inch) from case for 10 seconds: J, JG, or W package . . . . . . . . . . . . 300C Lead temperature 1,6 mm (1/16 inch) from case for 10 seconds: D, N, P, or PW package . . . . . . . . . 260C
Stresses beyond those listed under absolute maximum ratings may cause permanent damage to the device. These are stress ratings only, and functional operation of the device at these or any other conditions beyond those indicated under recommended operating conditions is not implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability. NOTES: 1. All voltage values, except differential voltages, are with respect to the midpoint between VCC+ and VCC . 2. Differential voltages are at IN+ with respect to IN . 3. The magnitude of the input voltage must never exceed the magnitude of the supply voltage or 15 V, whichever is less. 4. The output may be shorted to ground or to either supply. Temperature and /or supply voltages must be limited to ensure that the dissipation rating is not exceeded. DISSIPATION RATING TABLE PACKAGE D (8 pin) D (14 pin) FK J JG N P PW (8 pin) PW (14 pin) W TA 25C POWER RATING 680 mW 680 mW 680 mW 680 mW 680 mW 680 mW 680 mW 525 mW 700 mW 680 mW DERATING FACTOR 5.8 mW/C 7.6 mW/C 11.0 mW/C 11.0 mW/C 8.4 mW/C 9.2 mW/C 8.0 mW/C 4.2 mW/C 5.6 mW/C 8.0 mW/C DERATE ABOVE TA 33C 60C 88C 88C 69C 76C 65C 70C 70C 65C TA = 70C POWER RATING 465 mW 604 mW 680 mW 680 mW 672 mW 680 mW 640 mW 525 mW 700 mW 640 mW TA = 85C POWER RATING 378 mW 490 mW 680 mW 680 mW 546 mW 597 mW 520 mW N/A N/A 520 mW TA = 125C POWER RATING N/A N/A 273 mW 273 mW 210 mW N/A N/A N/A N/A 200 mW
VO = 0,
V/C pA nA pA nA V
IIO IIB
POST OFFICE BOX 655303 DALLAS, TEXAS 75265
VO = 0 VO = 0
VICR
TL071, TL071A, TL071B, TL072 TL072A, TL072B, TL074, TL074A, TL074B LOW-NOISE JFET-INPUT OPERATIONAL AMPLIFIERS
VOM
AVD
B1 ri CMRR
kSVR
25C
70
100
80
100
80
100
80
100
dB
25C 25C
1.4 14 120
2.5 25
1.4 14 120
2.5 25
1.4 14 120
2.5 25
1.4 14 120
2.5 25
mA dB
All characteristics are measured under open-loop conditions with zero common-mode voltage unless otherwise specified. Full range is TA = 0C to 70C for TL07_C,TL07_AC, TL07_BC and is TA = 40C to 85C for TL07_I. Input bias currents of a FET-input operational amplifier are normal junction reverse currents, which are temperature sensitive as shown in Figure 4. Pulse techniques must be used that maintain the junction temperature as close to the ambient temperature as possible.
TL071, TL071A, TL071B, TL072 TL072A, TL072B, TL074, TL074A, TL074B LOW-NOISE JFET-INPUT OPERATIONAL AMPLIFIERS
SLOS080D SEPTEMBER 1978 REVISED AUGUST 1996
VICR
VOM
Maximum peak output M i k t t voltage swing Large-signal differential g g voltage amplification Unity-gain bandwidth Input resistance Common-mode rejection ratio Supply-voltage rejection ratio (VCC /VIO) Supply current (each amplifier)
VO1/ VO2 Crosstalk attenuation AVD = 100 25C 120 120 dB Input bias currents of a FET-input operational amplifier are normal junction reverse currents, which are temperature sensitive as shown in Figure 4. Pulse techniques must be used that will maintain the junction temperature as close to the ambient temperature as possible. All characteristics are measured under open-loop conditions with zero common-mode voltage unless otherwise specified. Full range is TA = 55C to 125C.
TL071, TL071A, TL071B, TL072 TL072A, TL072B, TL074, TL074A, TL074B LOW-NOISE JFET-INPUT OPERATIONAL AMPLIFIERS
SLOS080D SEPTEMBER 1978 REVISED AUGUST 1996
0.003%
0.003%
10 k VO + CL = 100 pF RL = 2 k VI VI
TL071 OUT
IN IN +
N2 N1 100 k
1.5 k VCC
VO + RL CL = 100 pF 7
1 k
TL071, TL071A, TL071B, TL072 TL072A, TL072B, TL074, TL074A, TL074B LOW-NOISE JFET-INPUT OPERATIONAL AMPLIFIERS
SLOS080D SEPTEMBER 1978 REVISED AUGUST 1996
VOM
AVD
Large-signal Large signal differential voltage amplification Phase shift Normalized unity-gain bandwidth Normalized phase shift
Common-mode rejection ratio Supply current Total power dissipation Normalized slew rate Equivalent input noise voltage Total harmonic distortion Large-signal pulse response Output voltage
TL071, TL071A, TL071B, TL072 TL072A, TL072B, TL074, TL074A, TL074B LOW-NOISE JFET-INPUT OPERATIONAL AMPLIFIERS
SLOS080D SEPTEMBER 1978 REVISED AUGUST 1996
TYPICAL CHARACTERISTICS
INPUT BIAS CURRENT vs FREE-AIR TEMPERATURE
VOM Maximum Peak Output Voltage V VOM VCC = 15 V 15
100
12.5
10
7.5
0.1
2.5
0.01 75
50
25
25
50
75
100
125
0 100
1k
TA Free-Air Temperature C
Figure 4
MAXIMUM PEAK OUTPUT VOLTAGE vs FREQUENCY
15 VOM Maximum Peak Output Voltage V VOM VOM Maximum Peak Output Voltage V VOM VCC = 15 V RL = 2 k TA = 25C See Figure 2 15
12.5
12.5
10
10
VCC = 10 V
7.5
7.5
5 VCC = 5 V
2.5
2.5
0 100
1k
10 k 100 k f Frequency Hz
1M
10 M
0 10 k
Figure 6
Data at high and low temperatures are applicable only within the rated operating free-air temperature ranges of the various devices.
TA = 25C
TA = 125C
VCC = 5 V 10 k 100 k f Frequency Hz 1M 10 M
10
VCC = 10 V
Figure 5
TA = 55C
4M
10 M
Figure 7
TL071, TL071A, TL071B, TL072 TL072A, TL072B, TL074, TL074A, TL074B LOW-NOISE JFET-INPUT OPERATIONAL AMPLIFIERS
SLOS080D SEPTEMBER 1978 REVISED AUGUST 1996
TYPICAL CHARACTERISTICS
MAXIMUM PEAK OUTPUT VOLTAGE vs FREE-AIR TEMPERATURE
15 VOM VOM Maximum Peak Output Voltage V VOM Maximum Peak Output Voltage V VOM RL = 10 k 15
10
7.5
0 75
TA Free-Air Temperature C
Figure 8
12.5
10
7.5
2.5
Figure 10
Data at high and low temperatures are applicable only within the rated operating free-air temperature ranges of the various devices.
10
2.5
RL = 2 k
12.5
12.5
10
7.5
2.5
0 0.1
0.2
0.4
0.7 1
7 10
RL Load Resistance k
Figure 9
LARGE-SIGNAL DIFFERENTIAL VOLTAGE AMPLIFICATION vs FREE-AIR TEMPERATURE
1 75
TA Free-Air Temperature C
Figure 11
TL071, TL071A, TL071B, TL072 TL072A, TL072B, TL074, TL074A, TL074B LOW-NOISE JFET-INPUT OPERATIONAL AMPLIFIERS
SLOS080D SEPTEMBER 1978 REVISED AUGUST 1996
TYPICAL CHARACTERISTICS
LARGE-SIGNAL DIFFERENTIAL VOLTAGE AMPLIFICATION AND PHASE SHIFT vs FREQUENCY
106 VCC = 5 V to 15 V RL = 2 k TA = 25C 0 Differential Voltage Amplification
105
103
45
90
101
135
180 10 M
Figure 12
NORMALIZED UNITY-GAIN BANDWIDTH AND PHASE SHIFT vs FREE-AIR TEMPERATURE
1.3 1.03
1.2
Unity-Gain Bandwidth
1.01
0.99
0.8
0.98
0.7 75
0.97 125
Figure 13
Data at high and low temperatures are applicable only within the rated operating free-air temperature ranges of the various devices.
Phase Shift
104
11
TL071, TL071A, TL071B, TL072 TL072A, TL072B, TL074, TL074A, TL074B LOW-NOISE JFET-INPUT OPERATIONAL AMPLIFIERS
SLOS080D SEPTEMBER 1978 REVISED AUGUST 1996
TYPICAL CHARACTERISTICS
COMMON-MODE REJECTION RATIO vs FREE-AIR TEMPERATURE
89 CMRR Common-Mode Rejection Ratio dB ICC I CC Supply Current Per Amplifier mA VCC = 15 V RL = 10 k 2 1.8 1.6 1.4 1.2 1 0.8 0.6 0.4 0.2 0 0 2 4 6 8 10 12 14 16 |VCC | Supply Voltage V TA = 25C No Signal No Load
88
87
86
85
83 75
50
25
25
50
75
100
125
TA Free-Air Temperature C
Figure 14
SUPPLY CURRENT PER AMPLIFIER vs FREE-AIR TEMPERATURE
2 ICC I CC Supply Current Per Amplifier mA 1.8 1.6 1.4 1.2 1 0.8 0.6 0.4 0.2 0 75 50 25 0 25 50 75 100 125 VCC = 15 V No Signal No Load 250 PD Total Power Dissipation mW PD 225 200 175
75 50 25 0 75 50 25 0
TL071
25
TA Free-Air Temperature C
TA Free-Air Temperature C
Figure 16
Figure 17
Data at high and low temperatures are applicable only within the rated operating free-air temperature ranges of the various devices.
12
84
Figure 15
TOTAL POWER DISSIPATION vs FREE-AIR TEMPERATURE
VCC = 15 V No Signal No Load
50
75
100
125
TL071, TL071A, TL071B, TL072 TL072A, TL072B, TL074, TL074A, TL074B LOW-NOISE JFET-INPUT OPERATIONAL AMPLIFIERS
SLOS080D SEPTEMBER 1978 REVISED AUGUST 1996
TYPICAL CHARACTERISTICS
NORMALIZED SLEW RATE vs FREE-AIR TEMPERATURE
1.15 VCC = 15 V RL = 2 k CL = 100 pF
1.10
1.05
0.95
0.90
0.85 75
50
25
25
50
75
100
125
TA Free-Air Temperature C
Figure 18
TOTAL HARMONIC DISTORTION vs FREQUENCY
1 THD Total Harmonic Distortion % 0.4 VI and VO Input and Output Voltages V VCC = 15 V AVD = 1 VI(RMS) = 6 V TA = 25C 0.1 0.04 6
0.004
0.001 100
400
1k 4 k 10 k f Frequency Hz
40 k 100 k
Figure 20
Figure 21
0.01
50 40 30 20 10 0 10 4 2 0 2
40 100
400 1 k 4 k 10 k f Frequency Hz
40 k 100 k
Figure 19
Output
Input
2.5
3.5
13
TL071, TL071A, TL071B, TL072 TL072A, TL072B, TL074, TL074A, TL074B LOW-NOISE JFET-INPUT OPERATIONAL AMPLIFIERS
SLOS080D SEPTEMBER 1978 REVISED AUGUST 1996
TYPICAL CHARACTERISTICS
OUTPUT VOLTAGE vs ELAPSED TIME
28 24 Overshoot VO VO Output Voltage mV 20 90% 16 12 8 4 0
14
10% tr 0 0.1
Figure 22
TL071, TL071A, TL071B, TL072 TL072A, TL072B, TL074, TL074A, TL074B LOW-NOISE JFET-INPUT OPERATIONAL AMPLIFIERS
SLOS080D SEPTEMBER 1978 REVISED AUGUST 1996
APPLICATION INFORMATION
Table of Application Diagrams
APPLICATION DIAGRAM 0.5-Hz square-wave oscillator High-Q notch filter Audio-distribution amplifier 100-kHz quadrature oscillator AC amplifier RF = 100 k VCC + 3.3 k 15 V Output Input R1 C3 1 k R3 3.3 k f C1 9.1 k 1 R F C F C2 R2 TL071 + CF = 3.3 F 15 V TL071 + Output VCC PART NUMBER TL071 TL071 TL074 TL072 TL071 FIGURE 23 24 25 26 27
+ 2p
VCC + 1 M VCC + TL074 + VCC TL074 + VCC + TL074 + Output B VCC + VCC VCC + 100 k TL074 + Output C VCC Output A
1 F Input
100 k
100 F
15
TL071, TL071A, TL071B, TL072 TL072A, TL072B, TL074, TL074A, TL074B LOW-NOISE JFET-INPUT OPERATIONAL AMPLIFIERS
SLOS080D SEPTEMBER 1978 REVISED AUGUST 1996
APPLICATION INFORMATION
1N4148 6 sin t 18 pF 18 pF VCC + 88.4 k VCC + TL072 + 1 k 15 V 1N4148 18 k (see Note A) 6 cos t TL072 88.4 k 18 pF + VCC 1 k 18 k (see Note A) 15 V
VCC
88.4 k NOTE A: These resistor values may be adjusted for a symmetrical output.
16
IMPORTANT NOTICE Texas Instruments and its subsidiaries (TI) reserve the right to make changes to their products or to discontinue any product or service without notice, and advise customers to obtain the latest version of relevant information to verify, before placing orders, that information being relied on is current and complete. All products are sold subject to the terms and conditions of sale supplied at the time of order acknowledgement, including those pertaining to warranty, patent infringement, and limitation of liability. TI warrants performance of its semiconductor products to the specifications applicable at the time of sale in accordance with TIs standard warranty. Testing and other quality control techniques are utilized to the extent TI deems necessary to support this warranty. Specific testing of all parameters of each device is not necessarily performed, except those mandated by government requirements. CERTAIN APPLICATIONS USING SEMICONDUCTOR PRODUCTS MAY INVOLVE POTENTIAL RISKS OF DEATH, PERSONAL INJURY, OR SEVERE PROPERTY OR ENVIRONMENTAL DAMAGE (CRITICAL APPLICATIONS). TI SEMICONDUCTOR PRODUCTS ARE NOT DESIGNED, AUTHORIZED, OR WARRANTED TO BE SUITABLE FOR USE IN LIFE-SUPPORT DEVICES OR SYSTEMS OR OTHER CRITICAL APPLICATIONS. INCLUSION OF TI PRODUCTS IN SUCH APPLICATIONS IS UNDERSTOOD TO BE FULLY AT THE CUSTOMERS RISK. In order to minimize risks associated with the customers applications, adequate design and operating safeguards must be provided by the customer to minimize inherent or procedural hazards. TI assumes no liability for applications assistance or customer product design. TI does not warrant or represent that any license, either express or implied, is granted under any patent right, copyright, mask work right, or other intellectual property right of TI covering or relating to any combination, machine, or process in which such semiconductor products or services might be or are used. TIs publication of information regarding any third partys products or services does not constitute TIs approval, warranty or endorsement thereof.