Professional Documents
Culture Documents
Author
12-Feb-05
Alan C.
Comments
= = = =
10 s. 120 s. 60 s. -
Signalling diagram:
2. T7 Frequency of the HANDOVER_REQUIRED message Interpretation: The timer T7 supervises the frequency of the HANDOVER_REQUIRED message. Also the timer handover attempt and the following handover attempt related to the same connection. Timer start condition: The timer T7 starts when the BSC sends the HANDOVER_REQUIRED message to the M Timer stop condition: The timer T7 stops when the HANDOVER_COMMAND or the HANDOVER_REQUIRED_ the MSC, however, it can send the message only after the timer MinIntBetweenUnsuccHoAttempt has expired. Action performed on timer expiry: When the timer T7 expires, the HANDOVER_REQUIRED procedure is repea Appropriate value:
= = = =
5 s. 30 s. 20 s. -
Signalling diagram:
3. T8 Handover procedure supervision in the source BSC Interpretation: The timer T8 supervises the external handover procedure in the serving BSC. Timer start condition: The timer T8 starts when a HANDOVER_COMMAND message is received from the MSC Timer stop condition: The timer T8 stops when a CLEAR_COMMAND message (in the case of external handov Action performed on timer expiry: When the timer T8 expires, the BSC sends a CLEAR_REQUEST message to Appropriate value:
= = = =
8 s. 15 s. 12 s. -
Signalling diagram:
4. T10 Supervision of the assignment procedure Interpretation: The timer T10 supervises the assignment procedure. Timer start condition: The timer T10 starts before the BSC sends a PHYSICAL_CONTEXT_REQUEST messag Timer stop condition: The timer T10 stops when the MS sends either an ASSIGNMENT_COMPLETE or an ASS Action performed on timer expiry: When the timer T10 expires, the BSC sends an ASSIGNMENT_FAILURE me
Appropriate value:
= = = =
Signalling diagram:
5. T13 RESET guard period Interpretation: The timer T13 serves as a guard period for a local call clearing procedure. Timer start condition: The timer T13 starts when a RESET message has been received from the MSC. Timer stop condition: The timer T13 stops when an SSP/SPI (subsystem prohibited/signalling point inhibited) m Action performed on timer expiry: When the timer T13 expires, a reset acknowledgement message is sent to th Appropriate value:
= = = =
5 s. 30 s. 15 s. -
Signalling diagram:
6. T17 Overload procedure Interpretation: The timer T17 supervises the overload procedure in MSC overload. Timer start condition: The timer T17 starts when an OVERLOAD message is received from the MSC. For a det Timer stop condition: None. Action performed on timer expiry: When the timer T17 expires, the BSC takes new OVERLOAD messages into
Appropriate value:
= = = =
1 s. 120 s. 4 s. T17<T18
This timer is started with T18, and must expire before T18 expires.
Signalling diagram:
7. T18 Overload procedure Interpretation: The timer T18 supervises the overload procedure. For a detailed description see GSM 08.08, MS Timer start condition: The timer T18 starts when an OVERLOAD message is received from the MSC. The traffi Timer stop condition: None. Action performed on timer expiry: When the timer T18 expires, the traffic is increased on the next level.
Appropriate value:
= = = =
3 s. 180 s. 12 s. T18>T17
This timer is started with T17, and must expire after T17 expires.
Signalling diagram:
8. T3101 Supervision of the immediate assignment procedure Interpretation: The timer T3101 supervises the immediate assignment procedure. Timer start condition: The timer T3101 starts when the BSC sends an IMMEDIATE_ASSIGNMENT_CMD mess Timer stop condition: The timer T3101 stops when an ESTABLISH_IND message is received from the MS. Action performed on timer expiry: When the timer T3101 expires, the BSC sends an RF_CHANNEL_REL mess Appropriate value:
= = = =
1 s. 5 s. 3 s. -
Signalling diagram:
9. T3103 Supervision of the internal handover procedure Interpretation: The timer T3103 supervises the internal handover procedure. Timer start condition: The timer T3103 starts when the BSC sends a HANDOVER_CMD message is sent to the Timer stop condition: The timer T3103 stops when the BSC receives either a HANDOVER_CMPL message on Action performed on timer expiry: When the timer T3103 expires, a CLEAR_REQ message is sent to the MSC Appropriate value:
= = = =
Signalling diagram:
10. T3105_d Repetition of the PHYSICAL INFORMATION (SDCCH) Interpretation: Time out of the timer T3105 repeats the PHYSICAL_INFORMATION message during asynchron Timer start condition: When network sends the PHYSICAL_INFORMATION message, timer T3105 is set. Timer stop condition: If the network receives a correctly decoded layer 2 frame or the HANDOVER_FAILURE m Action performed on timer expiry: When the timer T3105_d expires, the sending of the PHYSICAL_INFORMAT Appropriate value:
11. T3105_f Repetition of the PHYSICAL INFORMATION (TCH) Interpretation: Time out of the timer T3105 repeats the PHYSICAL_INFORMATION message during asynchron Timer start condition: When network sends the PHYSICAL_INFORMATION message, timer T3105 is set. Timer stop condition: If the network receivs a correctly decoded TCH frame from the mobile station or the HAN Action performed on timer expiry: When the timer T3105_f expires, the sending of the PHYSICAL_INFORMATI Appropriate value:
12. T3107 Supervision of the assignment procedure Interpretation: The timer T3107 supervises the assignment procedure and the internal intracell handover. Timer start condition: The timer T3107 starts when the BSC sends an ASSIGNMENT_CMD message to the MS Timer stop condition: The timer T3107 stops when the BSC receives either an ASSIGNMENT_CMPL or ASSIG Action performed on timer expiry: When the timer T3107 expires, the new and the old channel are released, all MSC.
Appropriate value:
= = = =
Signalling diagram:
13. T3109 Supervision of the channel release procedure Interpretation: The timer T3109 supervises the channel release procedure. Timer start condition: The timer T3109 starts when the BSC sends a CHANNEL_REL message to the MS (via a Timer stop condition: The timer T3109 stops when the BTS sends a RELEASE_INDICATION message. This is Action performed on timer expiry: When the timer T3109 expires, the BSC sends an RF_CHANNEL_REL mess Appropriate value:
= 8 s. = 15 s. = 12 s. = -
Signalling diagram:
14. T3111 Delay of channel deactivation Interpretation: The timer T3111 delays the channel deactivation after disconnection of the main signalling link. I Timer start condition: The timer T3111 starts when the BSC receives the RELEASE_INDICATION message fro when the BSC receives the CLEAR_COMMAND message from the MSC. Timer stop condition: The timer T3111 always expires. Action performed on timer expiry: When the timer T3111 expires, an RF_CHANNEL_REL message is sent to th Appropriate value:
15. T3121 GSM to WCDMA RAN handover procedure supervision in the source BSC Interpretation: The timer T3121 supervises the external handover procedure from GMS to WCDMA RAN in the Timer start condition: The timer T3121 starts when a HANDOVER_COMMAND message is received from the M Timer stop condition: The timer T3121 stops when a CLEAR_COMMAND message has been received from the Action performed on timer expiry: When the timer T3121 expires, the BSC sends a CLEAR_REQUEST messag Appropriate value:
= = = =
8 s. 15 s. 12 s. -
Signalling diagrams:
16. T3122 Delay of sending another channel request message Interpretation: The timer T3122 delays the sending of another channel request. Timer start condition: The timer T3122 starts when the MS receives an IMMEDIATE_ASSIGNMENT_REJECT Timer stop condition: The timer T3122 stops when the MS makes a reselection for another cell. Action performed on timer expiry: When the timer T3122 expires, the MS sends a new CHANNEL_REQUEST m Appropriate value:
Min. = 2 s. Max. = 10 s.
17. T3168 Wait for Packet Uplink Assignment message Interpretation: The timer T3168 is used on the mobile station side to define when to stop waiting for a Packet U Appropriate value:
0 7 1 = -
Note After a modification to this timer it takes about 5 minutes for processes to get the new values. After 5 minutes disable and
18. T3192 Wait for release of the TBF after reception of the final block Interpretation: The timer T3192 is used on the mobile station side when the mobile station has received all of th (0=500ms, 1=1s, 2=1.5s, etc.). Appropriate value:
0 2 0 = -
Note After a modification to this timer it takes about 5 minutes for processes to get the new values. After 5 minutes disable and
19. T9101 Supervision of the SCCP connection release Interpretation: The timer T9101 supervises the reception of the SCCP_RELEASED (RLSD) message. Timer start condition: The timer T9101 starts when the BSC sends the CLEAR_COMPLETE message to the M Timer stop condition: The timer T9101 stops when the RLSD message has been received from the MSC. Action performed on timer expiry: When the timer T9101 expires, the BSC releases the SCCP connection by se Appropriate value:
Def. = 10 s. (non-modifiable)
Signalling diagram:
20. T9103 Supervision of the channel activation procedure Interpretation: The timer T9103 supervises the channel activation procedure. Timer start condition: The timer T9103 starts when the BSC sends the CHANNEL_ACTIVATION message to th Timer stop condition: The timer T9103 stops when the CHANNEL_ACTIVATION_ACK or the CHANNEL_ACTIV Action performed on timer expiry: When the timer T9103 expires, an RF_CHANNEL_REL message is sent to th Appropriate value:
Def. = 2 s. (non-modifiable)
Signalling diagram:
21. T9104 Supervision of the clear command from the MSC Interpretation: The timer T9104 supervises the clear command that comes from the MSC. Timer start condition: The timer T9104 starts when the BSC sends a CLEAR_CMD message to the MSC. Timer stop condition: The timer T9104 stops when the BSC receives a CLEAR_CMD message from the MSC. Action performed on timer expiry: When the timer T9104 expires, the CLEAR_REQ message is repeated a max Appropriate value:
= = = =
5 s. 20 s. 15 s. -
Signalling diagram:
22. T9105 Supervision of the SCCP connection procedure Interpretation: The timer T9105 supervises the SCCP connection procedure. Timer start condition: The timer T9105 starts when the BSC sends an SCCP_CONNECTION_REQ message to Timer stop condition: The timer T9105 stops when the BSC receives either an SCCP_CONNECTION_CONFIR Action performed on timer expiry: When the timer T9105 expires, the BSC sends a CHANNEL_REL message t Appropriate value:
= = = =
2 s. 240 s. 10 s. -
Signalling diagram:
23. T9108 Supervision of the physical context request procedure Interpretation: The timer T9108 supervises the physical context request procedure. Timer start condition: The timer T9108 starts when the BSC sends the PHYSICAL_CONTEXT_REQUEST mes Timer stop condition: The timer T9108 stops when the PHYSICAL_CONTEXT_CONFIRM message has been r Action performed on timer expiry: When the timer T9108 expires, an ASSIGNMENT_FAILURE message is sen Appropriate value:
Def. = 2 s. (non-modifiable)
Signalling diagram:
24. T9113 Supervision of the external handover procedure in the target BSC Interpretation: The timer T9113 supervises the external handover in the target BSC. Timer start condition: The timer T9113 starts when the BSC sends a HANDOVER_REQUEST_ACK message t Timer stop condition: The timer T9113 stops either when the MS sends a HANDOVER_CMP message or the M Action performed on timer expiry: When the timer T9113 expires, the BSC sends a CLEAR_REQUEST messag Appropriate value:
= = = =
8 s. 15 s. 13 s. -
Signalling diagram:
Figure: T9113 timer activation with a CLEAR_CMD message from the MSC
BSC Parameters
CELL IDENTIFIER
Interpretation: This parameter identifies the coding of the cell identifier used in the following messages: ASSIGNMENT_CO Appropriate value:
0 1 2 3 4 1
Interpretation: This parameter defines whether the blocking status of the A interface circuits is sent to the MSC when the B Appropriate value:
Signalling diagram:
Interpretation: This parameter defines whether the blocking status of the A interface circuits is sent to the MSC after the B Appropriate value:
Figure: BSC global reset followed by blocking UNBLOCK MSG IN GLOBAL RESET
Interpretation: This parameter defines whether the unblocking status of the A interface circuit is sent to the MSC if blocking Appropriate value:
Figure: BSC global reset followed by unblocking SEND SYS INFO GLOBAL RESET
Interpretation: This parameter chooses whether the MS access in the Air interface is restricted or not in the case of a glob Appropriate value:
Interpretation: This parameter informs the MS about cell barring when a RESET message is received from the MSC. If the Appropriate value:
Figure: MSC global reset ALLOW SENDING OF CONFUSION MESSAGES Interpretation: This parameter allows or prevents the sending of CONFUSION messages on the A interface. Appropriate value:
Interpretation: This parameter allows or prevents the sending of CIRCUIT_GROUP_BLOCK and CIRCUIT_GROUP_UNB Appropriate value:
Value= yes/no Def. = no Rule = ALARM LIMIT FOR UNAVAILABLE A-IF CIRCUITS
Interpretation: This parameter sets a limit for unavailable A interface circuits. If the number of unavailable A interface spee Appropriate value:
Rule = ALARM DELAY FOR UNAVAILABLE A-IF CIRCUITS Interpretation: This parameter defines the time during which the alarm conditions must be fulfilled before the alarm is set. Appropriate value:
= = = =
0 s 300 s 60 s -
Interpretation: This parameter defines an alarm limit for successive remote transcoder failures. If the number of successiv Appropriate value:
= = = =
1 5 3 -
ALLOW SENDING OF UNEQUIPPED_CIRCUIT MESSAGES Interpretation: This parameter allows or prevents the sending of UNEQUIPPED_CIRCUIT messages on the A interface. Appropriate value:
Interpretation: This parameter defines if the BSC sends the Timing Advance (TA) value to the MSC or not and how it is se Appropriate value:
= = = =
0 2 0 -
Interpretation: This parameter is used to change the preference if the HO_Required message sent by the BSC and the as Appropriate value:
Interpretation: This parameter is used to determine the duration for timers T3198 and T3200 and maximum value for coun Note
After a modification to this parameter it takes about 5 minutes for processes to get the new values. After 5 minutes disa Appropriate value:
= = = =
0 15 6 -
Interpretation: Whenever the mobile station receives a PACKET UPLINK ACK/NACK message, the mobile station shall in station shall perform an abnormal release with cell re-selection. If PAN_DEC, PAN_INC, or PAN_MAX are set to the value Note
After a modification to PAN_DEC, PAN_INC or PAN_MAX it takes about 5 minutes for processes to get the new values Appropriate value:
= = = =
0 15 1 -
Interpretation: Whenever the mobile station receives a PACKET UPLINK ACK/NACK message, the mobile station shall in station shall perform an abnormal release with cell re-selection. If PAN_DEC, PAN_INC, or PAN_MAX are set to the value Note
After a modification to PAN_DEC, PAN_INC or PAN_MAX it takes about 5 minutes for processes to get the new values
Appropriate value:
= = = =
0 15 1 -
Interpretation: Whenever the mobile station receives a PACKET UPLINK ACK/NACK message, the mobile station shall in station shall perform an abnormal release with cell re-selection. If PAN_DEC, PAN_INC, or PAN_MAX are set to the value Note
After a modification to PAN_DEC, PAN_INC or PAN_MAX it takes about 5 minutes for processes to get the new values Appropriate value:
= = = =
4 32 8 increases by 4
DOWNLINK DTX
Interpretation: When the Downlink DTX has been set active in the BSC, it depends on the MSC and on other network elem Appropriate value:
= = = =
F T F -
Interpretation: 00: Network operation mode I: the network sends a CS paging message for a GPRS-attached MS, either o receives CS paging messages on the packet data channel when it has been assigned a packet data channel.
01: Network operation mode II: the network sends a CS paging message for a GPRS-attached MS on the CCCH paging c packet data channel.
Note
After a modification to this parameter it takes about 5 minutes for processes to get the new values. After 5 minutes disa
Appropriate value:
= = = =
00 01 01 -
REPEAT COUNT FOR ALARM 3121 Interpretation: Repeat count for alarm Reset circuit acknowledgement missing from MSC. Appropriate value:
= = = =
0 255 10 -
FEP CORR WITH RXQUAL IN PC&HO ALGRTHM CL1 Interpretation: The FEP (Frame Error Probability) percentage value gives the correlation with the lower limit of an RxQual
The user is able to change each of the FEP percentage values (quality classes 1 7) independently from the other FER p
The Power Control and the Handover Algorithm uses the FEP correlation value in power control and handover decision-m Appropriate value:
= = = =
0 100 2.0
FEP CORR WITH RXQUAL IN PC&HO ALGRTHM CL2 Interpretation: See previous parameter. Appropriate value:
= = = =
0 100 4.0
FEP CORR WITH RXQUAL IN PC&HO ALGRTHM CL3 Interpretation: See parameter 21, FEP CORR WITH RXQUAL IN PC&HO ALGRTHM CL1. Appropriate value:
= = = =
0 100 6.0
FEP CORR WITH RXQUAL IN PC&HO ALGRTHM CL4. Interpretation: See parameter 21, FEP CORR WITH RXQUAL IN PC&HO ALGRTHM CL1. Appropriate value:
= = = =
0 100 8.0
FEP CORR WITH RXQUAL IN PC&HO ALGRTHM CL5. Interpretation: See parameter 21, FEP CORR WITH RXQUAL IN PC&HO ALGRTHM CL1. Appropriate value:
= = = =
0 100 10.0
FEP CORR WITH RXQUAL IN PC&HO ALGRTHM CL6. Interpretation: See parameter 21, FEP CORR WITH RXQUAL IN PC&HO ALGRTHM CL1. Appropriate value:
= = = =
0 100 12.0
FEP CORR WITH RXQUAL IN PC&HO ALGRTHM CL7. Interpretation: See parameter 21, FEP CORR WITH RXQUAL IN PC&HO ALGRTHM CL1.
Appropriate value:
= = = =
0 100 14.0
SGSN RELEASE Interpretation: This parameter defines the SGSN Release. Appropriate value:
= = = =
0 (The SGSN is Release 1998 or older.) 1 (The SGSN is Release 1999 onwards.) 1
MSC RELEASE Interpretation: This parameter defines the MSC Release. Appropriate value:
= = = =
0 (The MSC is Release 1998 or older.) 1 (The MSC is Release 1999 onwards.) 1
Interpretation: The maximum duration for a non-DRX (discontinuous reception) mode period in the cell. The value zero ind Note
The value should be coded so that values 0 - 7 correspond to 0, 1, 2, 4, 8, 16, 32 and 64. The values 0 - 7 should be st Appropriate value:
= = = =
Interpretation: The parameter defines when the two-way speech path connection is made during internal HOs for speech Note 0 = Always after Establish Indication from a BTS. 1 = Always after Handover Detection from a BTS.
2 = Always after Handover Detection from a BTS when a channel mode change or speech codec change happens durin Appropriate value:
= = = =
0 2 0
BATURA DEN
T4 T7 T8 T10 T13 T17 T18 T3101 T3103 T3105_D T3105_F T3107 T3109 T3111 T3121 T3122 T3168 T3192 T9101 T9103 T9104 T9105 T9108 T9113 CELL IDENTIFIER BLOCK MSG INCOMING GLOBAL RESET BLOCK MSG OUTGOING GLOBAL RESET UNBLOCK MSG IN GLOBAL RESET SEND SYS INFO GLOBAL RESET CELL BARRING INCOMING GLOBAL RESET ALLOW SENDING OF CONFUSION MESSAGES ALLOW CIRCUIT GROUP MESSAGES ALARM LIMIT FOR UNAVAILABLE A-IF CIRCUITS ALARM DELAY FOR UNAVAILABLE A-IF CIRCUITS ALARM LIMIT FOR SUCCESSIVE REMOTE TC FAIL ALLOW SENDING OF UNEQUIPPED CIRCUIT MESSAGES ALLOW SENDING OF TA VALUE TO MSC PREFERENCE PROCEDURE IN CONFLICT SITUATION BS_CV_MAX DECREMENT VALUE FOR COUNTER N3102 INCREMENT VALUE FOR COUNTER N3102 MAXIMUM VALUE FOR COUNTER N3102 DOWNLINK DTX 60.00 S 20.00 S 12.00 S 8.00 S 15.00 S 4.00 S 12.00 S 3.00 S 6.00 S 0.28 S 0.10 S 6.00 S 12.00 S 0.50 S 12.00 S 6.00 S 1.00 S 0.50 S 10.00 S 2.00 S 15.00 S 10.00 S 2.00 S 13.00 S LAC+CI YES YES NO YES NO NO NO 1 60 S 3 NO 0 ASSIGN 6 1 1 1 NO 60.00 S 20.00 S 12.00 S 8.00 S 15.00 S 4.00 S 12.00 S 3.00 S 6.00 S 0.28 S 0.10 S 6.00 S 12.00 S 0.50 S 12.00 S 6.00 S 1.00 S 0.50 S 10.00 S 2.00 S 15.00 S 10.00 S 2.00 S 13.00 S LAC+CI YES YES NO YES NO NO NO 1 60 S 3 NO 0 ASSIGN 6 1 1 1 NO
NMO - NETWORK MODE OF OPERATION REPEAT COUNT FOR ALARM 3121 FEP CORR WITH RXQUAL IN PC&HO ALGRTHM CL1 FEP CORR WITH RXQUAL IN PC&HO ALGRTHM CL2 FEP CORR WITH RXQUAL IN PC&HO ALGRTHM CL3 FEP CORR WITH RXQUAL IN PC&HO ALGRTHM CL4 FEP CORR WITH RXQUAL IN PC&HO ALGRTHM CL5 FEP CORR WITH RXQUAL IN PC&HO ALGRTHM CL6 FEP CORR WITH RXQUAL IN PC&HO ALGRTHM CL7 SGSN RELEASE MSC RELEASE DRX TIMER MAX TWO-WAY SPEECH PATH CONNECT TRIGGER POINT
BII
120.00 S 20.00 S 12.00 S 8.00 S 15.00 S 4.00 S 12.00 S 3.00 S 6.00 S 0.28 S 0.10 S 6.00 S 12.00 S 0.50 S 12.00 S 6.00 S 1.00 S 0.50 S 10.00 S 2.00 S 15.00 S 10.00 S 2.00 S 13.00 S LAC+CI YES YES NO YES NO NO NO 1 60 S 3 NO 0 ASSIGN 6 1 1 1 NO
CEMANI
60.00 S 20.00 S 12.00 S 8.00 S 15.00 S 4.00 S 12.00 S 3.00 S 6.00 S 0.28 S 0.10 S 6.00 S 12.00 S 0.50 S 12.00 S 6.00 S 1.00 S 0.50 S 10.00 S 2.00 S 15.00 S 10.00 S 2.00 S 13.00 S LAC+CI YES YES NO YES NO NO NO 1 60 S 3 NO 0 ASSIGN 6 1 1 1 NO
ITN
60.00 S 20.00 S 12.00 S 8.00 S 15.00 S 4.00 S 12.00 S 3.00 S 6.00 S 0.28 S 0.10 S 6.00 S 12.00 S 0.50 S 12.00 S 6.00 S 1.00 S 0.50 S 10.00 S 2.00 S 15.00 S 10.00 S 2.00 S 13.00 S LAC+CI YES YES NO YES NO NO NO 1 60 S 3 NO 0 ASSIGN 6 1 1 1 NO
JOMBAN G1
60.00 S 20.00 S 12.00 S 8.00 S 15.00 S 4.00 S 12.00 S 3.00 S 6.00 S 0.28 S 0.10 S 6.00 S 12.00 S 0.50 S 12.00 S 6.00 S 1.00 S 0.50 S 10.00 S 2.00 S 15.00 S 10.00 S 2.00 S 13.00 S LAC+CI YES YES NO YES NO NO NO 1 60 S 3 NO 0 ASSIGN 6 1 1 1 NO
PTPN
60.00 S 20.00 S 12.00 S 8.00 S 15.00 S 4.00 S 12.00 S 3.00 S 6.00 S 0.28 S 0.10 S 6.00 S 12.00 S 0.50 S 12.00 S 6.00 S 1.00 S 0.50 S 10.00 S 2.00 S 15.00 S 10.00 S 2.00 S 13.00 S LAC+CI YES YES NO YES NO NO NO 1 60 S 3 NO 0 ASSIGN 6 1 1 1 NO
SEMPU
60.00 S 20.00 S 12.00 S 8.00 S 15.00 S 4.00 S 12.00 S 3.00 S 6.00 S 0.28 S 0.10 S 6.00 S 12.00 S 0.50 S 12.00 S 6.00 S 1.00 S 0.50 S 10.00 S 2.00 S 15.00 S 10.00 S 2.00 S 13.00 S LAC+CI YES YES NO YES NO NO NO 1 60 S 3 NO 0 ASSIGN 6 1 1 1 NO
SIDOAR UM
60.00 S 20.00 S 12.00 S 8.00 S 15.00 S 4.00 S 12.00 S 3.00 S 6.00 S 0.28 S 0.10 S 6.00 S 12.00 S 0.50 S 12.00 S 6.00 S 1.00 S 0.50 S 10.00 S 2.00 S 15.00 S 10.00 S 2.00 S 13.00 S LAC+CI YES YES NO YES NO NO NO 1 60 S 3 NO 0 ASSIGN 6 1 1 1 NO
SIER
70.00 S 20.00 S 12.00 S 8.00 S 15.00 S 4.00 S 12.00 S 3.00 S 6.00 S 0.28 S 0.10 S 6.00 S 12.00 S 0.50 S 12.00 S 6.00 S 1.00 S 0.50 S 10.00 S 2.00 S 15.00 S 10.00 S 2.00 S 13.00 S LAC+CI YES YES NO YES NO NO NO 1 60 S 3 NO 0 ASSIGN 6 1 1 1 NO
TONGAS
60.00 S 20.00 S 12.00 S 8.00 S 15.00 S 4.00 S 12.00 S 3.00 S 6.00 S 0.28 S 0.10 S 6.00 S 12.00 S 0.50 S 12.00 S 6.00 S 1.00 S 0.50 S 10.00 S 2.00 S 15.00 S 10.00 S 2.00 S 13.00 S LAC+CI YES YES NO YES NO NO NO 1 60 S 3 NO 0 ASSIGN 6 1 1 1 NO