Professional Documents
Culture Documents
By:Mohammad Yousefi
1
: :
PREFACE
A turret machine tool has a slide table mounted on a machine base for movement toward and away from a workpiece to be machined. A turret head is indexably mounted on the slide table, and a plurality of multispindle heads mounted on the turret head at spaced angular intervals in an indexing direction of the turret head, each of the multispindle heads having a plurality of spindles disposed therein. A plurality of machine tools mounted on respective ends of the spindles, and a plurality of spindle gears are mounted on the spindles, respectively. A driven gear is mounted in each of the multispindle heads in mesh with the spindle gears through a train of gears. A drive gear is axially movably disposed in the turret head for movement into and out of mesh with the driven gear in one of the multispindle heads which has been indexed. A plurality of gear shafts are supported in a cantilevered fashion by each of the multispindle heads and project toward the turret head, the train of gears and the driven gear being mounted on the gear shafts. The multispindle heads can be highly accurately installed on the turret head, and the train of gears can easily be serviced. The turret machine tool is relatively light in weight, and can be manufactured relatively inexpensively.
1.turret lathe
The turret lathe, as we know it today, is a comparatively modern machine, and was developed from an ordinary engine lathe by the addition of revolving tool-holding devices called turrets. The turret was at first made of circular form, and rotated upon a vertical pivot which had a binding nut whereby it could be held in any desired position. The circumference of the circular turret was drilled and reamed for four tools projecting horizontally from it at angles of 90 degrees with each other. Later the number of tool holes was increased to six, and the turret was frequently made of hex-gonal form. The turret was at first located upon a lathe carriage in place of the tool block, and properly set in line with the lathe center by means of the cross-feed screw. The lateral feed, upon which the device depends for its action, was obtained by the operation of the feeding mechanism in the apron attached to the carriage. The object sought to be accomplished by the addition of this device to the lathe was that of carrying various drilling, reaming, counterboring, and similar tools by which several operations could be performed upon a piece of work without removing it from the chuck, or without any further change of tools than that of revolving the turret. The tools, when once adjusted, required no further alteration as the several pieces of work were completed and removed from the chuck, and other pieces substituted for a like series of operations. By this means the work could be performed much more rapidly, the producing value of the machine being correspondingly increased.
2.Types of turret lathes, and their nomenclature 2.1 The archetypical turret lathe: horizontal, manual
The archetypical turret lathe, and the first in order of historical appearance, is the horizontalbed, ` usually understood in context to refer to this type. The formative decades for this class of machine were the 1840s through 1860s, when the basic idea of mounting an indexable turret on a bench lathe or engine lathe was elaborated upon, developed, and disseminated into factory|factories.
(2) Engine lathes adapted to serve as turret lathes by having a hand-revolved turret mounted upon a laterally moving slide, supported upon a. shoe or saddle fitting the V's of the bed.
(3) The turret lathe proper, specially designed and built as such, with a turret revolved and fed by hand, supported by and pivoted upon a slide, which is in turn supported by a shoe or saddle fitted to the Va of the bed.
(4) A turret lathe designed and built in a similar manner to that last described, and in which there is a power feed for the cuts. It is so arranged that the turret is revolved automatically. This lathe is frequently called a semi-automatic turret lathe.
(5) A complete automatic turret lathe having a power feed for the cuts; a quick return of the turret slide, operated by power; with the turret automatically revolved at the end of its run.
The lathes described in the third, fourth, and fifth classes are usually provided with a carriage called a cross-slide, carrying one cutting tool in front and frequently another tool at the back, inverted so as to cut without reversing the direction of revolution of the work. A very useful modification of the type described in the third class is called the monitor lathe, probably from the fancied resemblance of its turret to the turret of the type of warship called a "monitor". In this lathe the slide upon which the turret is supported and pivoted is moved back and forth by means of a horizontal hand lever, and is therefore very rapid in its operation. From the fact that this constitutes a rapid hand feed for the turret, this type is adapted for light work or work upon soft metals. For this class of work it is a very rapid and efficient machine. Fig. 292 shows one of these machines. The lever A is for operating the turret slide B, carrying the turret C, which was first revolved by hand but later by a ratchet device located in its base and actuated by a pawl during the latter portion of the movement of the slide in withdrawing the cutting tools from the work. The lever D is for operating the cross-slide E, carrying a cutting-off tool and frequently a forming tool also.
4.SPECIAL FEATURES
Three piece face gear coupling allows tool disc to be indexed without lifting. It also ensures high repeat positioning accuracy an rigidity. 'Parallel Index' cam mechanism allows fast and smooth indexing of heavy tool disc's. Computer generated cam profiles ensure shock-free indexing action.
10
Totally enclosed, robust mechanism, with oil bath lubrication. Electrical elements are conveniently located in a separate area, free from oil and coolant.
PRINCIPLE OF WORKING Electric motor drives the cam shaft through a system of gears. Cam shaft indexes the follower shaft through a 'parallel index' drive mechanism. Cam shaft is also geared to the 'drum cam' which controls clamping and release of the 3 piece coupling. One revolution of cam shaft completes one indexing cycle of 'unclamping - indexing clamping'. Absolute position encoder gives feedback of the turret position. Proximity switch inspects the clamped position of the turret.
11
Specifications:
y y y y y y y y y y y y
Height of center: 80mm Number of tools: 8, 10, 12 Tool change time (adjustment): 0.4 sec Tool change and locking time (adjustment): 0.8 sec Hydraulic Working pressure: 40 kg/cm Pulling force of hydraulic cylinder: 4100 kg Radial load of tool end: 900 kg Axial load of tool front end: 780 kg Axial load of tool rear end: 350 kg Turret rotating movement of inertia: 15386 kgxcm Opposite side width of disc: 300 mm N.W. (without tool disc): 73 kgs
12
Specifications:
y y y y y y y y y y y
Height of center: 125mm Number of tools: 8, 10, 12 Tool change time (adjustment): 0.2 sec Tool change and locking time (adjustment): 0.5 sec Hydraulic Working pressure: 45 kg/cm Pulling force of hydraulic cylinder: 10360 kg Radial load of tool end: 2500 kg Axial load of tool front end: 3900 kg Axial load of tool rear end: 1500 kg Turret rotating movement of inertia: 63360 kgxcm Opposite side width of disc: 420 mm
13
14
15
16
REFERENCES
www.mtsdriventools.co.uk/img/tool-turret www.centroidcnc.com/images/8_position_cnc_turret news.thomasnet.com/images/large/552/552509 www.precisionengineer.co.uk/cooldrill.html www.allproducts.com/.../hydraulic_turret_06.html
17