Professional Documents
Culture Documents
Component Identification
Section 1
Please consider the environment before printing this paper. © 2006 SGI All Rights Reserved
This document is subject to periodic revision and
WARNING updating. Before designing scaffolds with SGI
THIS DOCUMENT IS INTENDED FOR USE BY EXPERIENCE SCAFFOLD
ENGINEERS. USE BY UNQUALIFIED PERSONS MAY RESULT IN DEATH, components, refer to this document on www.sgi360.ca
SERIOUS PERSONAL INJURY OR PROPERTY DAMAGE. to be sure you are using the most current revision.
LOADING INFORMATION CONTAINED IN THIS DOCUMENT IS
BASED UPON THE LOAD-CARRYING CAPACITY OF THE INDIVIDUAL Contact SGI for all scaffold loading not covered in
COMPONENTS. THE TOTAL LOADS (COMPONENT WEIGHT, PLANK this document.
WEIGHT, LIVE LOAD, MATERIAL LOAD, WIND LOAD, ETC.) TO BE
IMPOSED ON THE COMPLETE ASSEMBLY MUST BE CONSIDERED. ALL THIS DOCUMENT IS NOT TO BE REPRODUCED IN PART OR
LOADS ON INDIVIDUAL MEMBERS ARE TRANSMITTED TO OTHER IN WHOLE.
COMPONENTS AND ULTIMATELY TO THE GROUND. COMPENSATION
FOR THESE CUMULATIVE VERTICAL AND HORIZONTAL LOADS MUST BE
PROVIDED FOR EACH INDIVIDUAL SCAFFOLD APPLICATION.
All drawings in this guide are for illustrative purposes only. This guide
is intended for general information purposes only. Because of the many
WARNING variables which affect the performance of the product line, some of the
information in this brochure may not apply. For specific applications,
SERIOUS INJURY OR DEATH CAN RESULT FROM YOUR FAILURE TO contact SGI.
FAMILIARIZE YOURSELF, AND COMPLY WITH ALL APPLICABLE SAFETY
REQUIREMENTS OF PROVINCIAL REGULATIONS BEFORE ERECTING, USING Note: All scaffolds shall be erected, modified and dismantled only under
the supervision of a Competent Person. Erection, use, maintenance and
OR DISMANTLING THIS SCAFFOLD. disassembly must conform to current manufacturer’s instructions as well as
all federal, state, provincial and local regulations. Copies of complete SGI
WARNING Guidelines for these and other purposes are available from SGI
without charge.
FALL ARREST EQUIPMENT ATTACHED TO SCAFFOLD MAY NOT PREVENT
SERIOUS INJURY OR DEATH IF A FALL OCCURS.
Conversion Chart
Symbol Legend
c Denotes Centerline of Horizontals or Verticals
Material
Please consider the environment before printing this paper. © 2006 SGI All Rights Reserved
Table of Contents
Standards_____________________________________________________________________________________________________________ 4
Ledgers_______________________________________________________________________________________________________________ 5
Transoms_____________________________________________________________________________________________________________ 5
Bay Braces____________________________________________________________________________________________________________ 6
Side Brackets__________________________________________________________________________________________________________ 8
Stair Stringer_________________________________________________________________________________________________________ 10
Stair Treads__________________________________________________________________________________________________________ 10
Ladder___________________________________________________________________________________________________________ 11
Ladder Bracket___________________________________________________________________________________________________ 11
Gates____________________________________________________________________________________________________________ 12
Guardrail Standard_______________________________________________________________________________________________ 12
Aluminum Decks_____________________________________________________________________________________________________ 13
Clamps
Wedge Clamps___________________________________________________________________________________________________ 15
Steel Planks__________________________________________________________________________________________________________ 16
Aluminum I-Beam____________________________________________________________________________________________________ 17
Base Collar___________________________________________________________________________________________________________ 19
Spigot_______________________________________________________________________________________________________________ 19
Pigtail Pin____________________________________________________________________________________________________________ 20
Please consider the environment before printing this paper. © 2006 SGI All Rights Reserved
Component Identification
Standards
Part No. Effective Length Overall Length Weight Material
m in m in kg lb
Overall Length
Effective Length
081102 0.00 0’ 0” 0.24 9¼ 1.7 2.6 M3,
235.0 mm
081102 M3 9.25 “
Coupling Pin
11.75 mm
081105
70 mm 3/ ”–16 Hex Bolt w/ Self
8 115.0 mm 70.0 mm
35 mm Locking Jam Nut 4.53 “ 2.76 “
34.0 mm
M7 1.34 “
M1
40.0 mm
1.57 “
Please consider the environment before printing this paper. © 2006 SGI All Rights Reserved
4
Component Identification
Ledgers
Part No. Effective Width Overall Width Net Width Weight Material
m in m in m in kg lb
Standard
Wedge
M8
M1
Effective Width
Transoms
Part No. Effective Width Overall Width Net Width Weight Material
m in m in m in kg lb
8 Effective Width
Please consider the environment before printing this paper. © 2006 SGI All Rights Reserved
5
Component Identification
Bay Braces
Part No. Standard Spacing Overall Length Bolt Spacing Weight Material
m in m in m in kg lb
080410 3.05 10’ 0” 3.68 12’ 1” 3.52 11’ 6” 9.4 20.7 M2, M8
080407 2.13 7’ 0” 2.96 9’ 9” 2.81 9’ 3” 7.9 17.4 M2, M8
080405 1.57 5’ 2” 2.60 8’ 7” 2.45 8’ 0” 6.9 15.2 M2, M8
080403 1.15 3’ 10” 2.37 7’ 9” 2.23 7’ 4” 6.6 14.5 M2, M8
Spacing of Standards
M8
M2
2000
Wedge
Spacing of Standards
Overall Length
Bolt Spacing
Please consider the environment before printing this paper. © 2006 SGI All Rights Reserved
6
Component Identification
System Solid Screw Jack
Part No. Maximum Extension Minimum Extension Adjustment Range Overall Height Weight
m in m in m in m in kg lb
Adjustment Range
101.6
101.6 (4”)
152 (6”)
Handle
4-014
2”
Overall Height
152 (6”)
Maximum Extension
101.6 (4”)
Handle
101.6 (4”)
152 (6”)
Base Plate
3.5”
2”
4
01
4-
7
Component Identification
Side Brackets with Single Layer Head
Part No. Effective Length Overall Length Net Width Weight Material
m in m in m in kg lb
Effective Width
(Spacing of Standards)
M3
Net Width
M1
M8
M5
c
Saddle
M2
M11
080688/080665 c
080611 1.15 3’ 10” 1.15 3’ 10” 1.05 3’ 5” 12.0 26.4 M1, M3, M8
Overall Width
Effective Width
(Spacing of Standards)
Net Width M3
Ledger Head
081102 Coupling Pin
M1
081105 3/18”–16 Hex Bolt
3
/8”–16 Locking Jam Nut
0.50m
(1’ 8”) M8
M1
Ledger Head
M1
c
M5
Please consider the environment before printing this paper. © 2006 SGI All Rights Reserved
8
Component Identification
Truss Ledgers
Part No. Effective Length Overall Length Net Width Weight Material
m in m in m in kg lb
c c
Effective Width
Overall Width
Net Width
0.09 m (3.5”)
M4 M4
M4
M8
080310/080307
082128 8.52 28’ 0” 8.47 27’ 10” 8.37 27’ 5” 96.0 211.2 M4 , M8
082121 6.39 21’ 0” 6.34 20’ 10” 6.24 20’ 6” 71.2 156.6 M4 , M8
082117 5.18 17’ 0” 5.13 16’ 10” 5.03 16’ 6” 59.0 129.8 M4 , M8
082114 4.26 14’ 0” 4.21 13’ 10” 4.11 13’ 6” 48.5 106.7 M4 , M8
c Effective Width c
(Spacing Standards)
Overall Width
Net Width
M4
0.50 m (20”)
M4 M4
M8
082128/082121/082117/082114
Please consider the environment before printing this paper. © 2006 SGI All Rights Reserved
9
Component Identification
Stair Stringer
Part No. Standard Spacing Shipping Length Weight
m in m in kg lb
Stair Tread
Part No. Tread Width Slot Spacing Weight
m in m in kg lb
c c
Spacing of Standards
Slot Spacing
2.00 m
(6’7”)
Tread
Width
080801 080802
c c
Effective Width
Overall Width
Net Width
M8
080203 M1
Please consider the environment before printing this paper. © 2006 SGI All Rights Reserved
10
Component Identification
Access Ladder
Part No. Overall Height Effective Height Outside Width Effective Width Weight
m in m in m in m in kg lb
Overall
Height
Effective
Perforated Non-skid Rung
Height
Effective
Width
0715 Outside
Width
Hex Bolt
Effective Width See Required
Socket Size
081501
Please consider the environment before printing this paper. © 2006 SGI All Rights Reserved
11
Component Identification
Access Gate
Part No. Effective Width Weight
m in kg lb
0.50 m
(1’ 8”)
Effective Width
c
081801
Guardrail Standard
Part No. Effective Width Weight Material
m in kg lb
M1
0.50 m
(1’ 8”)
M7
Overall
Length
0.50 m
(1’ 8”)
Please consider the environment before printing this paper. © 2006 SGI All Rights Reserved
12
Component Identification
Aluminum Decks - Galvanized Steel Top
Part No. Effective Length Weight
m in kg lb
Effective
Length
483 mm
(19”)
Uplift Latch
0812
Effective
Length
483 mm
(19”)
Uplift Latch
0810
Please consider the environment before printing this paper. © 2006 SGI All Rights Reserved
13
Component Identification
Laminated Veneer Lumber (LVL)
Part No. Overall Length Weight
m in kg lb
Overall
Length
0608
Please consider the environment before printing this paper. © 2006 SGI All Rights Reserved
14
Component Identification
Wedge Clamps
Part No. Description Weight
kg lb
110122 110222
Beam Clamps
Part No. Description Weight
kg lb
110801
Please consider the environment before printing this paper. © 2006 SGI All Rights Reserved
15
Component Identification
Steel Planks
Part No. Effective Length Overall Length Weight Material
m in m in kg lb
M11
M12
Uplift Latch
0811
69.9 mm
(3”)
Effective Length
Overall Length
Please consider the environment before printing this paper. © 2006 SGI All Rights Reserved
16
Component Identification
Aluminum Scaffold Tube
Part No. Effective Length Weight Material
in kg lb/ft
SH40
1.9 in
1105
Aluminum I-Beam
Part No. Effective Length Overall Length Base Width Top Width Weight Material
in mm in mm in mm in kg lb
0106 6.5”x Available request 166.5 6.5 127.0 5.0 108 4.25 1.65kg/ft 3.7lb/ft 6061 - T6 Mill finish
0107 7.5”x Available request 190.5 7.5 127.0 5.0 108 4.25 2.3kg/ft 5.15lb/ft 6061 - T6 Mill finish
Top
Width
Overall Length
0106 Base
Width
Please consider the environment before printing this paper. © 2006 SGI All Rights Reserved
17
Component Identification
Beam Geometry & Structural Properties for 6½" Aluminum Beam
Metric Imperial
Please consider the environment before printing this paper. © 2006 SGI All Rights Reserved
18
Component Identification
Base Collar
Part No. Effective Length Overall Length Weight Material
m in m in kg lb
M6
Overall
Length 100 mm
Effective (4”)
Length
M7
M1
081101
Ø122
Spigot
Part No. Diameter Weight Material
mm in kg lb
M3
ø 11.75 mm
35 mm
M5
Effective
Height
Please consider the environment before printing this paper. © 2006 SGI All Rights Reserved
19
Component Identification
Pigtail Pin
Part No. Diameter Fits Tube Weight
mm in mm in kg lb
081103
Please consider the environment before printing this paper. © 2006 SGI All Rights Reserved
20