Professional Documents
Culture Documents
Class 150
US units [inch]
Connection dimensions
Nominal Thickness
Bolt circle Bolt hole diameter min. (2) - (4)
Pipe Outside diameter Bolting (1), (5)
diameter (1), (5) (1), (5)
Size
O W l Number b tf
½ 3.50 2.38 5/8 4 1/2 0.38
¾ 3.88 2.75 5/8 4 1/2 0.44
1 4.25 3.12 5/8 4 1/2 0.50
1¼ 4.62 3.50 5/8 4 1/2 0.56
1½ 5.00 3.88 5/8 4 1/2 0.62
2 6.00 4.75 3/4 4 5/8 0.69
2½ 7.00 5.50 3/4 4 5/8 0.81
3 7.50 6.00 3/4 4 5/8 0.88
4 9.00 7.50 3/4 8 5/8 0.88
5 10.00 8.50 7/8 8 3/4 0.88
6 11.00 9.50 7/8 8 3/4 0.94
8 13.50 11.75 7/8 8 3/4 1.06
10 16.00 14.25 1 12 7/8 1.12
12 19.00 17.00 1 12 7/8 1.19
14 21.00 18.75 1 1/8 12 1 1.31
16 23.50 21.25 1 1/8 16 1 1.38
18 25.00 22.75 1¼ 16 1 1/8 1.50
20 27.50 25.00 1¼ 20 1 1/8 1.62
24 32.00 29.50 1 3/8 20 1 1/4 1.81
Table 10.4.3-1: ASME B16.5 – dimensions of flanges [inch] – class 150
O W l Number b tf
½ 90 60.5 15,9 4 12,70 9.6
¾ 100 69.9 15,9 4 12,70 11.2
1 110 79.2 15,9 4 12,70 12.7
1¼ 115 88.9 15,9 4 12,70 14.3
1½ 125 98.6 15,9 4 12,70 15.9
2 150 120.7 19,1 4 15,88 17.5
2½ 180 139.7 19,1 4 15,88 20.7
3 190 152.4 19,1 4 15,88 22.3
4 230 190.5 19,1 8 15,88 22.3
5 255 215.9 22,2 8 19,05 22.3
6 280 241.3 22,2 8 19,05 23.9
8 345 298.5 22,2 8 19,05 27.0
10 405 362.0 25,4 12 22,23 28.6
12 485 431.8 25,4 12 22,23 30.2
14 535 476.3 28,6 12 25,4 33.4
16 595 539.8 28,6 16 25,4 35.0
18 635 577.9 31,8 16 28,58 38.1
20 700 635.0 31,8 20 28,58 41.3
24 815 749.3 34,93 20 31,75 46.1
Table 10.4.3-2: ASME B16.5 – dimensions of flanges [mm] – class 150
Notes:
(1) For flange bolt holes, see ASME B16.5 para 6.5
(2) The minimum thickness of these loose flanges, in sizes NPS 3½ and smaller, is slightly greater than the thickness of flanges on
fittings, table ASME B16.5 F9, which are reinforced by cast integral with the body of the fitting.
(3) When these flanges are required with flat face, the flat face may be either the full tf-dimension thickness plus 0.06 inch/2 mm., or
the tf dimension thickness without the raised face height. See para. ASME B16.5 6.3.2 for additional restrictions.
(4) The flange dimensions illustrated are for regularly furnished 0.06 inch/2 mm raised face (except lapped); for requirements of other
facings, see ASME B16.5 figure F7
(5) For spot facing, see ASME B16.5 para 6.6
Class 300
US units [inch]
Connection dimensions
Nominal Thickness
Bolt circle Bolt hole diameter min. (2) - (4)
Pipe Outside diameter Bolting (1), (5)
diameter (1), (5) (1), (5)
Size
O W l Number b tf
½ 3.75 2.62 5/8 4 1/2 0.50
¾ 4.62 3.25 3/4 4 5/8 0.56
1 4.88 3.50 3/4 4 5/8 0.62
1¼ 5.25 3.88 3/4 4 5/8 0.69
1½ 6.12 4.50 7/8 4 3/4 0.75
2 6.50 5.00 3/4 8 5/8 0.81
2½ 7.50 5.88 7/8 8 3/4 0.94
3 8.25 6.62 7/8 8 3/4 1.06
4 10.00 7.88 7/8 8 3/4 1.19
5 11.00 9.25 7/8 8 3/4 1.31
6 12.50 10.62 7/8 12 3/4 1.38
8 15.00 13.00 1 12 7/8 1.56
10 17.50 15.25 1 1/8 16 1 1.81
12 20.50 17.75 1 1/4 16 1 1/8 1.94
14 23.00 20.25 1 1/4 20 1 1/8 2.06
16 25.50 22.50 1 3/8 20 1 1/4 2.19
18 28.00 24.75 1 3/8 24 1 1/4 2.31
20 30.50 27.00 1 3/8 24 1 1/4 2.44
24 36.00 32.00 1 5/8 24 1 1/2 2.69
Table 10.4.3-3: ASME B16.5 – dimensions of flanges [inch] – class 300
Notes:
(1) For flange bolt holes, see ASME B16.5 para 6.5
(2) These flanges may be supplied with a flat face. The flat face may be either the full tf dimension thickness plus 0.06 inch/2 mm or
the tf dimension thickness without the raised face height. See para. ASME B16.5 6.3.2 for additional restrictions.
(3) The flange dimensions illustrated are for regularly furnished 0.06 inch/2 mm raised face (except lapped); for requirements of other
facings, see ASME B16.5 fig. F-7.
(4) For welding end bevel, see AMSE B 16.5 para. 6.7.
(5) For spot facing, see ASME B16.5 para 6.6
Class 600
US units [inch]
Connection dimensions
Nominal Thickness
Bolt circle Bolt hole diameter min.
Pipe Outside diameter Bolting (2), (3)
diameter (2), (3) (2), (3)
Size
O W l Number b tf
½ 3.75 2.62 5/8 4 1/2 0.56
¾ 4.62 3.25 3/4 4 5/8 0.62
1 4.88 3.50 3/4 4 5/8 0.69
1¼ 5.25 3.88 3/4 4 5/8 0.81
1½ 6.12 4.50 7/8 4 3/4 0.88
2 6.50 5.00 3/4 8 5/8 1.00
2½ 7.50 5.88 7/8 8 3/4 1.12
3 8.25 6.62 7/8 8 3/4 1.25
4 10.75 8.50 1 8 7/8 1.50
5 13.00 10.50 1 1/8 8 1 1.75
6 14.00 11.50 1 1/8 12 1 1.88
Table 10.4.3-5: ASME B16.5 – dimensions of flanges [inch] – class 600
Notes:
(2) For flange bolt holes, see ASME B16.5 para 6.5
(3) For spot facing, see ASME para 6.6
Class 900
US units [inch]
Connection dimensions
Nominal Thickness
Bolt circle Bolt hole diameter min.
Pipe Outside diameter Bolting (2), (3)
diameter (2), (3) (2), (3)
Size
O W l Number b tf
½
¾
1
1¼ Use class 1500 dimensions in these sizes
1½
2
2½
3 9.50 7.50 1 8 7/8 1.50
4 11.50 9.25 1 1/4 8 1 1/8 1.75
Table 10.4.3-7: ASME B16.5 – dimensions of flanges [inch] – class 900
Notes:
(2) For flange bolt holes, see ASME B16.5 para 6.5
(3) For spot facing, see ASME para 6.6
Class 1500
US units [inch]
Connection dimensions
Nominal Thickness
Bolt circle Bolt hole diameter min.
Pipe Outside diameter Bolting (2), (3)
diameter (2), (3) (2), (3)
Size
O W l Number b tf
½ 4.75 3.25 7/8 4 3/4 0.88
¾ 5.12 3.50 7/8 4 3/4 1.00
1 5.88 4.00 1 4 7/8 1.12
1¼ 6.25 4.38 1 4 7/8 1.12
1½ 7.00 4.88 1 1/8 4 1 1.25
2 8.50 6.50 1 8 7/8 1.50
2½ 9.62 7.50 1 1/8 8 1 1.62
3 10.50 8.00 1 1/4 8 1 1/8 1.88
4 12.25 9.50 1 3/8 8 1 1/4 2.12
Table 10.4.3-9: ASME B16.5 – dimensions of flanges [inch] – class 1500
Notes:
(2) For flange bolt holes, see ASME B16.5 para 6.5
(3) For spot facing, see ASME para 6.6
Class 2500
US units [inch]
Connection dimensions
Nominal Thickness
Bolt circle Bolt hole diameter min.
Pipe Outside diameter Bolting (2), (3)
diameter (2), (3) (2), (3)
Size
O W l Number b tf
½ 5.25 3.50 7/8 4 3/4 1.19
¾ 5.50 3.75 7/8 4 3/4 1.25
1 6.25 4.25 1 4 7/8 1.38
1¼ 7.25 5.12 1 1/8 4 1 1.50
1½ 8.00 5.75 1 1/4 4 1 1/8 1.75
2 9.25 6.75 1 1/8 8 1 2.00
2½ 10.50 7.75 1 1/4 8 1 1/8 2.25
3 12.00 9.00 1 3/8 8 1 1/4 2.62
4 14.00 10.75 1 5/8 8 1 1/2 3.00
Table 10.4.3-11: ASME B16.5 – dimensions of flanges [inch] – class 2500
Notes:
(2) For flange bolt holes, see ASME B16.5 para 6.5
(3) For spot facing, see ASME para 6.6