Professional Documents
Culture Documents
TC2.1A
AA
Contents Page
1. Technical Specifications, Connections and Chassis
Overview 2
2. Safety & Maintenance Instructions, Warnings and
Notes 4
3. Directions for Use 5
4. Mechanical Instructions 17
5. Service Modes, Error Codes and Faultfinding 18
6. Block Diagram, Testpoints, and Overviews
Block Diagram 25
Testpoint Overview Main Carrier 26
7. Electrical Diagrams and PWB’s Diagram PWB
Mono Carrier 27 33-36
Mono Carrier: Power Supply (Diagram A1) 28 33-36
Mono Carrier: Line Deflection (Diagram A2) 29 33-36
Mono Carrier: Frame Deflection (Diagram A3) 30 33-36
Mono Carrier: Tuner IF (Diagram A4) 30 33-36
Mono Carrier: Video and Sound IF(Diagram A5) 31 33-36
Mono Carrier: Audio Power Ampl. (Diagram A6) 32 33-36
Mono Carrier: Rear I/O Cinch (Diagram A7) 32 33-36
CRT (Diagram B) 37 38
Secam Panel (Diagram C) 38 38
Side AV Panel (Diagram E) 39 39
8. Alignments 41
9. Circuit Description 44
Abbreviation List 44
IC Pin Description 45
10 Spare Parts List 47
11 Revision List 49
©
Copyright 2003 Philips Consumer Electronics B.V. Eindhoven, The Netherlands.
All rights reserved. No part of this publication may be reproduced, stored in a
retrieval system or transmitted, in any form or by any means, electronic,
mechanical, photocopying, or otherwise without the prior permission of Philips.
Published by LM 0364 Service PaCE Printed in the Netherlands Subject to modification EN 3122 785 13690
EN 2 1. TC2.1A Technical Specifications, Connections and Chassis Overview
Note:
Below described specifications are not valid for one product, IN 1
but for the whole product range. See Product Survey for
specific models.
Figures can deviate slightly from the actual situation, due to OUT
different set executions.
CL 26532099_036.eps
120902
1.1 Technical Specifications
Figure 1-2 Rear connections
1.1.1 Reception
Monitor Out
Tuning system : VST
1 - Video CVBS (1 Vpp / 75 Ω)
Colour systems : PAL B/G, D/K, I
2 - Audio L (0.5 Vrms / 1 kΩ)
: SECAM B/G, D/K
3 - Audio R (0.5 Vrms / 1 kΩ)
Sound systems : Mono
A/V connections : NTSC 3.58, 4.43
: PAL 60 AV1 In
Channel selections : 100 channels 4 - Video CVBS (1 Vpp / 75 Ω)
: U, V, S, H 5 - Audio L (0.5 Vrms / 10 kΩ)
Aerial input : 75 Ω, IEC-type 6 - Audio R (0.5 Vrms / 10 kΩ)
1.2 Connections
1.2.1 Front (or Side) Connections and Front (or Top) Control
Side A/V In
SIDE A/V
R
AUDIO
L (MONO)
FRONT PANEL
IN2
VIDEO
POWER
TV/AV MENU VOL CH. SENSOR STANDBY
cl 26532099_037.eps
230802
cl 26532099_035.eps
230802
Safety regulations require that during a repair: • In order to prevent damage to ICs and transistors, avoid all
• Due to the chassis concept, a very large part of the circuitry high voltage flashovers. In order to prevent damage to the
(incl. deflection) is 'hot'. Therefore, connect the set to the picture tube, use the method shown in Fig. 2-1, to
mains via an isolation transformer. discharge the picture tube. Use a high voltage probe and a
• Replace safety components, indicated by the symbol , multi-meter (position VDC). Discharge until the meter
only by components identical to the original ones. Any reading is 0 V (after approx. 30 s).
other component substitution (other than original type) may
increase risk of fire or electrical shock hazard.
• Wear safety goggles when you replace the CRT.
V
Safety regulations require that after a repair, you must return
the set in its original condition. Pay, in particular, attention to
the following points:
• General repair instruction: as a strict precaution, we advise
you to re-solder the solder connections through which the
horizontal deflection current is flowing. In particular this is
valid for the:
1. Pins of the line output transformer (LOT). CL96532156_040.eps
140501
2. Fly-back capacitor(s).
3. S-correction capacitor(s).
Figure 2-1 Discharge picture tube
4. Line output transistor.
5. Pins of the connector with wires to the deflection coil.
6. Other components through which the deflection current • All ICs and many other semiconductors are susceptible to
flows. electrostatic discharges (ESD, ). Careless handling
Note: This re-soldering is advised to prevent bad connections during repair can reduce life drastically. Make sure that,
due to metal fatigue in solder connections, and is therefore only during repair, you are connected with the same potential as
necessary for television sets more than two years old. the mass of the set by a wristband with resistance. Keep
• Route the wire trees and EHT cable correctly and secure components and tools also at this potential. Available ESD
them with the mounted cable clamps. protection equipment:
• Check the insulation of the mains cord for external – Complete kit ESD3 (small tablemat, wristband,
damage. connection box, extension cable and ground cable)
• Check the strain relief of the mains cord for proper function, 4822 310 10671.
to prevent the cord from touching the CRT, hot – Wristband tester 4822 344 13999.
components, or heat sinks. • Together with the deflection unit and any multi-pole unit,
• Check the electrical DC resistance between the mains plug flat square picture tubes form an integrated unit. The
and the secondary side (only for sets that have an isolated deflection and the multi-pole units are set optimally at the
power supply). Do this as follows: factory. We do not recommend adjusting this unit during
1. Unplug the mains cord and connect a wire between the repair.
two pins of the mains plug. • Be careful during measurements in the high voltage
2. Turn on the main power switch (keep the mains cord section and on the picture tube.
unplugged!). • Never replace modules or other components while the unit
3. Measure the resistance value between the pins of the is 'on’.
mains plug and the metal shielding of the tuner or the • When you align the set, use plastic rather than metal tools.
aerial connection of the set. The reading should be This will prevent any short circuits and the danger of a
between 4.5 MΩ and 12 MΩ. circuit becoming unstable.
4. Switch the TV 'off' and remove the wire between the
two pins of the mains plug. 2.4 Notes
• Check the cabinet for defects, to prevent the possibility of
the customer touching any internal parts.
• Measure the voltages and waveforms with regard to the
chassis (= tuner) ground (), or hot ground (), depending
2.2 Maintenance Instructions on the tested area of circuitry.
• The voltages and waveforms shown in the diagrams are
We recommend a maintenance inspection carried out by indicative. Measure them in the Service Default Mode (see
qualified service personnel. The interval depends on the usage chapter 5) with a colour bar signal and stereo sound (L: 3
conditions: kHz, R: 1 kHz unless stated otherwise) and picture carrier
• When a customer uses the set under normal at 475.25 MHz (PAL) or 61.25 MHz (NTSC, channel 3).
circumstances, for example in a living room, the • Where necessary, measure the waveforms and voltages
recommended interval is three to five years. with () and without () aerial signal. Measure the
• When a customer uses the set in an environment with voltages in the power supply section both in normal
higher dust, grease, or moisture levels, for example in a operation () and in standby (). These values are
kitchen, the recommended interval is one year. indicated by means of the appropriate symbols.
• The maintenance inspection includes the following actions: • The picture tube panel has printed spark gaps. Each spark
1. Perform the 'general repair instruction' noted above. gap is connected between an electrode of the picture tube
2. Clean the power supply and deflection circuitry on the and the Aquadag coating.
chassis. • The semiconductors indicated in the circuit diagram and in
3. Clean the picture tube panel and the neck of the picture the parts lists, are interchangeable per position with the
tube. semiconductors in the unit, irrespective of the type
indication on these semiconductors.
Directions for Use TC2.1A 3. EN 5
Note:
Figures can deviate slightly from the actual situation, due to
different set executions.
Before you mount the rear cover, perform the following checks:
1. Check whether the AC power cord is mounted correctly in
A its guiding brackets.
2. Replace the strain relief of the AC power cord into the
cabinet.
3. Check whether all cables are replaced in their original
position.
11
B 4
CL 26532099_046.eps
120902
Figure 4-1
EN 18 5. TC2.1A Service Modes, Error Codes and Fault Finding
No Picture,
No Raster,
No Sound,
Fuse Blown
No Picture,
No Raster,
No Sound,
abnormal +B
voltage
Yes No No
Is the voltage
Replace IC201 Replace Q401
of pin 25
and R402
of IC201 5V?
No
Is the
Yes Is the output Yes
resistance to Check R233,
voltage of IC401
earth of pin 25 C231 and C233
9V?
of IC201 OK?
No No
No Picture,
No Sound,
Noise dots
No No No No
No
Replace the
tuner
CL 36532028_027.eps
160403
No
No No No
Check Q208,
OK Check the Check the
Q209 and
waveform at waveform at
their peripheral
pin 30 of IC201 pin 45 of IC201
components
No
No
Check Q202,
Replace IC201 Q203, Q210 and
their peripheral
components CL 36532028_019.eps
160403
No Raster,
No Picture,
Sound OK
Yes OK
Yes OK
OK
OK
Picture OK,
No Sound
Check the
Check the Vcc No peripheral
voltage at pin 4
supply circuits
of IC601
of pin 4 of IC601
OK
OK OK
Check the
Check the Check the
OK waveforms
speakers and the peripheral
between pin 8 & 10
leads connected components of
and pin 11 & 13 of
with them pin 1 of IC601
IC601
No
OK OK
Tuning control
does not work
Check the
Check the 9V circuit from
power supply pin 60 of IC201
circuit for the to VT terminal
tuner of the tuner CL 36532028_022.eps
160403
The channels
cannot be stored
Check the Hsync Check waveform Check Q202, Check the IF and
impulse No at pin 45 of IC201 OK Q203 and their OK AFT section of
waveform at with video signal peripheral IC201 and its
pin 62 of IC 201 input components peripheral circuits
OK No No
The channels
cannot be
switched
Check the
Check the Check the
No OK peripheral
voltages of voltage of
components of
pin 4 & 5 pin 1 & 61
pin 1 & 61
of the tuner of IC201
of IC201
OK No
Replace the
Replace IC201
tuner
CL 36532028_025.eps
160403
5.1.11 No Color
No Color
No Yes OK
Check the
Check the peripheral
Re-setting
antenna components of
pin 47 of IC201 CL 36532028_024.eps
160403
One
Horizontal
Line
Check the
No
deflect yoke Correct it
junction terminal
OK
OK
OK
Personal Notes:
Block Diagrams, I2C Supply, and Testpoint Overview TC2.1A 6. 25
Block Diagram
B A5 A1
A6
A3
A2
A4
A7 E
CL 36532028_001.eps
170403
Block Diagrams, I2C Supply, and Testpoint Overview TC2.1A 6. 26
Testpoint Overview
Testpoint Overview
Freq:15.60kHz Pk-Pk:11.38V
Freq:50Hz Pk -Pk:51.6V
Freq:50Hz Pk -Pk:1.52V
Freq:50Hz Pk -Pk:781mV
Freq:64.0us Pk-Pk:95 7V
Freq:1k Hz Pk -Pk:1.24V
CL 36532028_003.eps
080403
Circuit Diagrams and PWB Layouts TC2.1A 7. 28
A1 Power Supply
CL 36532028_004.eps
080403
Circuit Diagrams and PWB Layouts TC2.1A 7. 29
A2 Line Deflection
CL 36532028_005.eps
080403
Circuit Diagrams and PWB Layouts TC2.1A 7. 30
CL 36532028_006.eps CL 36532028_007.eps
080403 080403
Circuit Diagrams and PWB Layouts TC2.1A 7. 31
CL 36532028_008.eps
080403
Circuit Diagrams and PWB Layouts TC2.1A 7. 32
CL 36532028_009.eps CL 36532028_010.eps
080403 080403
Circuit Diagrams and PWB Layouts TC2.1A 7. 33
PART1
CL 36532028_13a.eps
100403
Circuit Diagrams and PWB Layouts TC2.1A 7. 34
PART2
CL 36532028_13b.eps
100403
Circuit Diagrams and PWB Layouts TC2.1A 7. 35
PART3
CL 36532028_13c.eps
100403
Circuit Diagrams and PWB Layouts TC2.1A 7. 36
PART 4
CL 36532028_13d.eps
100403
Circuit Diagrams and PWB Layouts TC2.1A 7. 37
CRT Panel
B CRT Amplifier
CL 36532028_011.eps
080403
Circuit Diagrams and PWB Layouts TC2.1A 7. 38
CL 36532028_014.eps
080403
Circuit Diagrams and PWB Layouts TC2.1A 7. 39
E Side AV Panel
CL 36532028_012.eps
080403
CL 36532028_015.eps
080403
Circuit Diagrams and PWB Layouts TC2.1A 7. 40
Personal Notes:
Alignments TC2.1A 8. EN 41
8. Alignments
Index of this chapter 7. Select COLP to adjust the sub-colour by tuning the
1. Hardware alignments amplitude of "a", "b", ',e" and "d" to the same level.
2. Software alignments
a b c
8.1 Hardware alignments
d
8.1.1 Flowchart of alignment procedure: A
CL 26532099_039.eps
260802
Figure 8-3
8.1.5 Adjustment of Sub-contrast, Sub-tint and Sub-colour for 8.1.9 Adjustment of Picture Geometry (PAL)
NTCS and PAL Signal.
1. Apply a crosshatch pattern (PAL signal) to the RF input, in
1. Enter the D-mode, and connect the probe of an STANDARD status.
oscilloscope to the conjunction between R201 and P201 2. Select HPOS to adjust the Horizontal centre.
(B-out). 3. Select VP50 to adjust the Vertical centre.
2. Apply the Grey-scale/Colour-bar (NTSC signal) to the AV 4. Select HIT to adjust the Vertical amplitude.
input, in STANDARD status. 5. Select VLIN to adjust the vertical linearity.
3. Select CNTC to adjust the sub-contrast, until that the 6. Select VSC to adjust the vertical S-correction.
amplitude "A' is 2.5V pp as shown below.
4. Select COLC to adjust the sub-colour by tuning the 8.1.10 Adjustment of Picture Geometry (NTSC)
amplitude of "a" and "d" to the same level.
5. Select TNTC to adjust the sub-tint by tuning the amplitude 1. Apply a crosshatch pattern (NTSC signal) to the RF input,
of "b" and "c" to the same level. in STANDARD status.
6. Apply the Grey-scale/Colour-bar (PAL signal) to the AV 2. Select HPS to adjust the Horizontal centre.
input, in STANDARD status. 3. Select VP60 to adjust the Vertical centre.
EN 42 8. TC2.1A Alignments
Item Description Default value Press "8" to enter the volume alignment menu 1.
CNTX Contrast max. 59
Item Description Default value
CNTN Contrast min. 8
V25 Volume output level at 25% 50
BRTX Brightness max. (delta from cen- 20
V50 Volume output level at 50% 5C
tre position)
V100 Volume output level at 100% 70
BRTN Brightness min. (delta from cen- 25
tre position) Press "9" to enter the picture alignment menu 2.
COLX Colour max. (delta from centre 4F
position) Item Description Default value
COLN Colour min. (delta from centre 0 SVM SVM 0
position) PYNX Normal Horizontal sync max. 28
TNTX Tint max. (delta from centre posi- 4A PYNN Normal Horizontal sync min. 18
tion) PYXS Search Horizontal sync max. 22
TNTN Tint min. (delta from centre posi- 4A PYNS Search Horizontal sync min. 1E
tion)
Press "CALENDAR” to enter the OSD setting menu.
Press "4" to enter the sharpness setting menu.
Alignments TC2.1A 8. EN 43
9.2.1 HCF4066
PUMP
UP
PIN CONNECTIONS THERMAL
PROTECTION
IN/OUT 1
SW 14 VDD
A
SIGNAL A AMP
OUT/IN 2 13 CONTROL
OUT/IN 3
SW 12 CONTROL
D
SIGNAL B
IN/OUT 4 11 IN/OUT
SIGNAL D
CONTROL 5
SW 10 OUT/IN
B 1 2 3 4 5 6 7
GND
VCC
PUMP UP OUT
VERT. OUTPUT
INVERTING INPUT
CONTROL 6 9 OUT/IN
SIGNAL C
VSS 7
SW 8 IN/OUT
C
S-.......
CL 36532028_028.eps CL 36532028_029.eps
080403
080403
9.2.4 MC44608P-40p
9.2.2 M24C08
VCC
Demag 1 8 Vi
3
E0-E2 SDA Isense 2 7
WC GND 4 5 Driver
(Top View)
VSS
AI02033 AWL = Manufacturing Code
YYWW = Date Code
CL 36532028_031.eps
080403
Signal Names
E0, E1, E2 Chip Enable Figure 9-4 Pin connections MC44608P-40p
SDA Serial Data
WC Write Control
VSS Ground
M24Cxx
PINNING
VC1 1
SYMBOL PIN DESCRIPTION
n.c. 2
VC1 1 DC volume control 1
CL 36532028_034.eps
180403
R410 9965 000 15076 10k 5% 1W D818 9965 000 17892 TERC05-10 R518 9965 000 15588 2.7k 5% 0.5W
R412 4822 111 31023 47k 5% 0.16W D830 3141 018 51230 FR104 R521 9965 000 17939 100k 5% 0.25W
R413 4822 111 31028 15k 5% 0.16W D831 3141 018 51160 HER108 R522 9965 000 12519 1k 5% 0.16W
R414 9965 000 08285 18k 5% 0.16W D833 3141 018 51230 FR104 R523 4822 116 82086 680Ω 5% 0.16W
R414 9965 000 12516 12k 5% 0.16W D835 4822 130 11443 1SS136 R524 4822 111 31034 2.7k 5% 0.16W
R415 9965 000 12519 1k 5% 0.16W D838 9965 000 17890 16HSC R525 4822 116 82086 680Ω 5% 0.16W
R418 9965 000 15075 1Ω 5% 1W D839 4822 130 34382 BZX79-B8V2 R526 4822 116 82086 680Ω 5% 0.16W
R441 9965 000 15077 1.2k 5% 1W D840 9965 000 17891 BZX79-C6V2 R527 4822 116 82086 680Ω 5% 0.16W
R602 4822 050 13303 33k 1% 0,4W
R604A 9965 000 12519 1k 5% 0.16W
R610 9965 000 12519 1k 5% 0.16W
R611 9965 000 14050 10k 5% 0.16W
R612 9965 000 15057 4.7k 5% 0.16W IC001 9965 000 17857 M24C08 L505 9965 000 14925 Ferrite bead BF60 for C508
R613 9965 000 15057 4.7k 5% 0.16W IC201 9965 000 17858 8821KPNG4GD9/ L506 9965 000 14925 Ferrite bead BF60 for C508
R614 9965 000 14050 10k 5% 0.16W 8821CPNG4GD9
R620 9965 000 15780 0.22Ω 5% 2W IC301 9965 000 17860 LA7840
R622 9965 000 12519 1k 5% 0.16W IC401 9965 000 17859 L7809CV
R633 4822 111 31033 22k 5% 0.16W IC402 9965 000 17861 UA7805C
R636 4822 111 31033 22k 5% 0.16W IC601 4822 209 13646 TDA7057AQ/N2 D501 4822 130 30621 1N4148
R637 9965 000 12519 1k 5% 0.16W IC603 9965 000 14978 HEF4066 D502 4822 130 30621 1N4148
R640 9965 000 15773 4.7Ω 5% 0.25W IC801 9322 136 56682 MC44608P40
R802 9965 000 17901 1M 5% 0.5W IC802 9965 000 17895 HPC922-C
R804 9965 000 17577 0.1M 1% 0.25W Q002 4822 130 41947 2SC1815Y
R804A 9965 000 17897 12k 5% 0.25W Q003 4822 130 42959 2SA1015Y
R806 9965 000 15057 4.7k 5% 0.16W Q005 4822 130 42959 2SA1015Y Q501 4822 130 60578 2SC2482
R807 9965 000 17896 3.6k 5% 0.16W Q101 9965 000 14974 2SC3779D Q502 4822 130 60578 2SC2482
R808 9965 000 17900 22k 10% 5W Q103 5322 130 40217 2N3904 Q503 4822 130 60578 2SC2482
R809 9965 000 12519 1k 5% 0.16W Q202 4822 130 42959 2SA1015Y Q510 4822 130 42959 2SA1015Y
R810 9965 000 15780 0.22Ω 5% 2W Q203 9965 000 15654 2SK2541
R811 9965 000 15667 470Ω 5% 0.25W Q208 4822 130 41947 2SC1815Y
R811A 9965 000 14059 22Ω 5% 0.25W Q209 4822 130 42959 2SA1015Y
R812 9965 000 17902 8.2M 5% 1W Q210 4822 130 42959 2SA1015Y Side AV Panel [E]
R831 9965 000 15776 56k 5% 0.5W Q211 4822 130 42594 DTC144ES
R832 9965 000 15074 4.7Ω 5% 0.5W Q401 4822 130 60578 2SC2482
R833 9965 000 17898 220Ω 5% 0.25W Q402 9965 000 14972 3DD1555 Various
R834 4822 111 31036 3.3k 5% 0.16W Q603 4822 130 41947 2SC1815Y
R835 9965 000 15666 3.9k 5% 0.25W Q604 4822 130 42683 DTC124ES 0000 9965 000 17921 Side AV panel 14'
R836 9965 000 17899 10k 10% 5W Q605 4822 130 42959 2SA1015Y 0000 9965 000 17976 Side AV panel 21'
R837 9965 000 15409 15k 5% 2W Q606 4822 130 42594 DTC144ES P1101 9965 000 17924 Socket Ye/Wh/Re
R838 4822 050 13303 33k 1% 0,4W Q607 4822 130 42594 DTC144ES P605 9965 000 15144 Connector 2P TJC3-2A
R844 9965 000 14050 10k 5% 0.16W Q608 4822 130 41947 2SC1815Y P606 9965 000 15144 Connector 2P TJC3-2A
R850 4822 111 31046 6.2k 5% 0.16W Q609 4822 130 41947 2SC1815Y
R901 9965 000 12519 1k 5% 0.16W Q801 9965 000 17894 2SK2996
R904 4822 111 31025 75Ω 5% 0.16W Q830 9965 000 17893 2SC2688L
R912 9965 000 12519 1k 5% 0.16W Q831 4822 130 41947 2SC1815Y
R914 9965 000 12623 82Ω 5% 0.16W Q832 4822 130 41947 2SC1815Y C1001A 9965 000 14069 100µF 20% 16V
R917 4822 111 31025 75Ω 5% 0.16W Q905 4822 130 41947 2SC1815Y C1001B 9965 000 14069 100µF 20% 16V
R922 4822 050 13303 33k 1% 0,4W
R922A 9965 000 17647 27k 5% 0.16W
R923 9965 000 13960 470Ω 5% 0.16W
R924 4822 111 31023 47k 5% 0.16W Picture Tube Panel [B]
R925 4822 111 31023 47k 5% 0.16W R1001A 9965 000 12549 220Ω 55 0.16W
R926 4822 111 31023 47k 5% 0.16W R1001B 9965 000 12549 220Ω 55 0.16W
R927 4822 111 31023 47k 5% 0.16W
Various
R961 9965 000 12519 1k 5% 0.16W
R962 9965 000 12519 1k 5% 0.16W 0000 9965 000 17937 CRT panel 14'
RT801 9965 000 17904 PTC 20Ω 20% 0000 9965 000 17964 CRT panel 21'
RT802 9965 000 15782 NTC 4.7Ω 18% 0000 9965 000 17970 Picture tube socket 21'
VR830 9965 000 17903 Potmeter B10K S501 9965 000 17942 Picture tube socket 14'
L002 9965 000 15123 10µH 5% C501 9965 000 13964 680pF 5% 50V
L080 9965 000 15126 33µH 5% C501 9965 000 17968 680pF 5% 50V
L103 9965 000 15121 1µH 10% C502 9965 000 13964 680pF 5% 50V
L201 9965 000 15124 22µH 5% C502 9965 000 17968 680pF 5% 50V
L204 9965 000 15123 10µH 5% C503 9965 000 13964 680pF 5% 50V
L207 9965 000 15124 22µH 5% C503 9965 000 17968 680pF 5% 50V
L208 9965 000 15124 22µH 5% C504 9965 000 15184 0.01µF 10% 500V
L209 9965 000 15238 27µH 5% C505 9965 000 17941 330pF 10% 2kV
L411 9965 000 15130 Coil 40µH C505 9965 000 17969 220pF 10% 2kV
L412 9965 000 15129 Linearity coil 50µH C506 9965 000 17940 1µF 20% 250V
L804 9965 000 15193 100µH 10% C507 9965 000 15099 0.01µF +80%~20% 50V
L843 9965 000 15126 33µH 5% C507 9965 000 17966 0.01µF +80-20% 50V
T401 9965 000 17887 Transf. Hor. Drive C508 9965 000 14070 220µF 20% 16V
T402 9965 000 15131 LOT 14' BSC250-231 C510 9965 000 17877 180pF 5% 50V
T402 9965 000 17975 LOT 21' BSC25-0299D C510 9965 000 17967 180pF 5% 50V
T801 9965 000 15195 Line filter LCL-2821A C511 9965 000 17877 180pF 5% 50V
T803 9965 000 17917 Transf. BCK-4001-72B C511 9965 000 17967 180pF 5% 50V
C512 9965 000 17877 180pF 5% 50V
C512 9965 000 17967 180pF 5% 50V
C514 9965 000 15099 0.01µF +80%~20% 50V