Professional Documents
Culture Documents
Professional Pilots
Ray Preston
2010
Navigation for Professional Pilots
Page 2
Navigation for Professional Pilots
Introduction:
This text was created for use in the course Avia 160 as part of the Selkirk College Professional Aviation
Program, which leads to the Canadian Commercial Pilot License with Multi-engine and Instrument Rating.
This text is intended as an adjunct to a 48 hour lecture series on the topic of navigation. Assignments,
tests, and exams supplement this text and the lectures. Flight planning exercises include both VFR and IFR
cross-countries. Students will become expert at preparing VNC maps and completing navlogs for VFR cross
countries. They will also use LO charts and the Canada Air Pilot to plan IFR cross-countries.
This book explains both theoretical and practical principles of flight navigation, including visual and radio
navigation based on VOR, ADF, and DME. This course covers principles of intercepting and maintaining a
radio course. It also covers flying DME arcs. An introduction to procedure turns is included.
The text is supplemented by several computer simulations of the Selkirk College Aviation Intranet, which is
on the web at Selair.selkirk.ca.
Students in this course are expected to become expert at the use of the CR(or 6) navigation computer.
This text was written based on the assumption that readers hold a private pilot license and as such have
certain basic knowledge about aviation in general and navigation in particular.
Page 3
Navigation for Professional Pilots
Page 4
Navigation for Professional Pilots
Table of Contents:
Chapter 1 .......................................................................................................................................................13
Chapter 2 .......................................................................................................................................................35
Definition of Velocity, and two useful deductions from the definition .................................................35
ICE-T ................................................................................................................................................38
Page 5
Navigation for Professional Pilots
Chapter 3 .......................................................................................................................................................59
Bracketing .................................................................................................................................................64
Page 6
Navigation for Professional Pilots
Chapter 4 .......................................................................................................................................................95
LO Charts ..............................................................................................................................................95
HI Charts...............................................................................................................................................96
Page 7
Navigation for Professional Pilots
Longitude...................................................................................................................................... 141
Page 8
Navigation for Professional Pilots
Page 9
Navigation for Professional Pilots
Page 10
Navigation for Professional Pilots
Page 11
Navigation for Professional Pilots
Page 12
Chapter 1
Text Overview
Everyone knows what it means to “have a plan.” In “flight planning” we develop a plan for a flight. For
example your plan might require knowing:
What navigation equipment (from eyeballs, to VOR, to GPS, etc.) will be used
Accommodation at destination
Customs arrangements
ETC
The above list is not complete; the point being made here is that flight planning is a large undertaking
covering many different items of concern regarding a flight. At an airline many people are employed to
ensure that all the passenger handling aspects of flight planning are looked into. Experts also plan routes
for optimum advantage (cost) taking wind, ATC fees, departure and arrival fees, etc. into account. The
process can be very complex. For example, many international airline flights don’t fly by the shortest route
for two reasons: For one every nation they over fly charges a fee, so flights may detour around some
Navigation for Professional Pilots
airspace spending more money on fuel, but saving in the long run by avoiding high ATC fees. In addition,
the shortest route is not always the quickest, if a strong tailwind (jet stream) can be located, or a strong
headwind avoided.
By the end of this course you must be fully competent at planning VFR flights, but, most commercial airline
flights are IFR flights, and as such are governed by a set of regulations that you will learn to take into
account during this course. For example, one requirement is to have an alternate airport to divert to in the
event that landing at the primary destination becomes impossible. By the end of this course you will be
fully competent to plan an IFR flight from any point within Canada to any other point. International flights
will covered in second year.
In this course we will concentrate on the planning time and fuel for a flight. Route selection will be
comparatively simple. We will consider the preferred IFR routes published in the Canada Flight
Supplement, and terrain and weather. We won’t usually concern ourselves with avoiding ATC fees or
political boundaries because most of our flights will be domestic. Airline flight planners often adjust to
avoid these, but we will concentrate on choosing an altitude that is optimum for the wind given a specified
route.
Flight logistics such as arranging food for passengers, where to park and service the airplane, etc won’t
receive a lot of attention due to our limited time. But you must recognize that these things are crucial to
real world commercial flight operations. You will learn where to find the required information, and some
of these matters will be included in the exercises.
After graduation, expect passenger handling and logistics aspects of flight planning to take considerably
more of your time than calculating time and fuel. By the end of this course you should be able determine
time and fuel for a given flight within a few minutes. For your commercial pilot flight test you are allowed
45 minutes, but that should be twice as much time as you actually need. Your skill at doing this level of
basic flight planning quickly and accurately will free up the time for the logistics aspects of flight planning
that your employer will expect you to master.
Pilotage means flying from point to point by visually following features on the ground. It is the way you
drive your car and it is often a practical way to fly an airplane. For example: to fly from Castlegar to
Revelstoke simply follow the Columbia River.
Dead-reckoning (DR) means to determine the one heading and time that will take the airplane directly to a
point, allowing for wind. DR is by definition flight along a straight line path. Most of this course is devoted
to learning how to dead-reckon.
Radio navigation means that the location of the airplane is determined by referring to instruments such as
VOR, ADF, or GPS. This is necessary when flying IFR. In this course you will learn the basics of IFR radio
Page 14
Navigation for Professional Pilots
navigation. Radio navigation is NOT distinct from pilotage or DR; in fact both can be applied to radio
navigation.
In real-world VFR navigating, pilots use a combination of pilotage and DR. DR dominates on long flights,
especially over terrain that lacks distinctive features. Any VFR flight over water must be a DR flight for
example. Pilotage dominates on shorter flights, but it can only be used when the ground has distinctive
features so that the pilot can accurately determine position visually. Even on a long flight some portions of
all VFR flights require pilotage. Usually the leg just after takeoff until established at the set heading point
requires pilotage. And the final circuit joining and landing is also a pilotage leg. DR is the most efficient
means of navigation, but if the terrain has good, distinctive, features some pilotage is practical especially
when doing things such as diverting around poor weather or special use airspace.
Often some radio navigation will be used, even on a VFR flight – thus most flights require pilotage, DR, and
radio navigation. In this course we will generally keeps these techniques separated for instructional
purposes, but in the real world they should be used together to achieve an efficient flight with the lowest
possible workload for the pilot.
Page 15
Navigation for Professional Pilots
Sample Questions 1
1. A pilot sees a local shopping mall and flies toward it.
a. This is DR navigation
2. A pilot is over a town s/he recognizes and turns south to join left base for the active runway
a. This is DR navigation
3. A pilot tunes a VOR and determines the track to the station is 030°. S/he then turns to that
heading without concern for the strong westerly wind. The pilot turns left, then right, then left
again, following the VOR needle until s/he gets to the station.
a. This is DR navigation
4. A pilot is trying to find a small lake. S/he flies a heading of 220 until the lake comes into sight,
then flies directly to the lake.
a. This is DR navigation
Page 16
Navigation for Professional Pilots
5. A pilot follows a road to a particular intersection then flies heading 360 until the airport comes
into view.
a. This is DR navigation
Page 17
Navigation for Professional Pilots
The ISA is simply a temperature model, i.e. it specifies how temperature changes in the atmosphere. The
ISA is divided into temperature layers known as the troposphere, stratosphere, and thermosphere. The
standard temperature is 15 C at sea level and decreases 1.98 C per thousand feet in the troposphere. By
36,100 feet the temperature has reached -56 C. In the Stratosphere temperature remains isothermal
(constant temperature) at -56 C. In the thermosphere temperature begins to rise again, but no civilian
aeroplanes fly that high so we will ignore the thermosphere.
The chemical makeup of the atmosphere does not change with altitude. The temperature, chemistry of the
atmosphere, and the force of gravity collectively determine the pressure and density of the air throughout
the ISA. It is important to realize that temperature, pressure, and density are inextricably connected to
each other by a law of physics called the gas law. The gas law states that pressure is proportional to
density and temperature. You can find more details on this in your aerodynamics text.
Page 18
Navigation for Professional Pilots
Aircraft performance depends on air density but airplanes do not come with an instrument to measure it.
They do however have a thermometer to measure temperature and an altimeter, which measures air
pressure. The gas law relates air density to these two values. In the ISA the following values apply:
Pressure
ISA Temp Density
3
Altitude C Inches Hg slugs / ft
Pressure Altitude
The most convenient instrument available to pilots for measuring air pressure is the aircraft altimeter.
Pilots do not have a barometer (an instrument for measuring air pressure) to measure pressure in units of
inches of mercury. When a pilot sets the altimeter scale to 29.92 it reads an altitude, but in effect it is
giving the air pressure from the table above. Once set to 29.92 altimeter reads an altitude called pressure
altitude. If the pressure altitude is 4,000’ the air pressure is 25.84 as shown in the table above. Fill in the
values for air pressure in the table below:
Page 19
Navigation for Professional Pilots
Inches Hg
Sea level
3000’
5,000’
7,000
9,000
The only way to get a precise pressure altitude is to set a calibrated altimeter to 29.92 and read the value
on the instrument. This is not convenient for flight planning however, so we need a method to estimate
pressure altitude.
Notice that in the ISA pressure drops about one inch of mercury for every thousand feet up to 10,000’. This
is an approximation, but it is pretty close. Armed with this knowledge it is possible to calculate the
pressure altitude without using an actual altimeter. This is convenient since it means we can flight plan
without needing access to an altimeter. To calculate pressure altitude we need to know the current
altimeter setting and the actual altitude of the altimeter setting source.
First a very simple example: An airport at sea level (such as CYVR) reports an altimeter setting of 28.86. In
this case the air pressure is 28.86 and the pressure altitude is 1000’ as we can see from the table above.
How would we calculate this mathematically?
Difference +1.06
Page 20
Navigation for Professional Pilots
Notice that the calculation gives a value of 1060’ when the correct value is 1000’. This small error is
acceptable for flight planning purposes. You should keep in mind that the calculation of pressure altitude
results in estimation. To get a precise pressure altitude you must use a calibrated altimeter.
Below is a more complex pressure altitude calculation in which the altimeter source is not at sea level.
Difference -0.75
TIP:
You may find it hard to remember whether to add or subtract the correction from the altimeter source
altitude. Remember that when the altimeter setting is more than 29.92 it is like flying at a lower altitude,
and vice versa.
Density Altitude
Density altitude represents the altitude in the ISA with the equivalent air density. Once you know the
pressure altitude (in effect the air pressure) and air temperature, density altitude can be calculated in
accordance with the gas law, which states that air density is proportional to air pressure and inversely
proportional to air temperature.
Page 21
Navigation for Professional Pilots
Many Pilot Operating Handbooks are designed so that it is not necessary to calculate density altitude since
the manufacturer provides performance charts based on pressure altitude and temperature. This is wise
on their part because calculating density altitude accurately requires a complex formula.
The C-172 and King Air manuals you will use in this course have charts based on pressure altitude and
temperature. In effect the density altitude calculation is incorporated into the charts. For these airplanes it
is not necessary to calculate density altitude.
Our B95 charts are based on density altitude, and therefore you must calculate its value. Because
temperature is usually close to standard a reasonable estimation of density altitude can be made by
adjusting pressure altitude 120 feet for every degree the temperature varies from standard. For example if
the temperature is 3 C colder than ISA then density altitude will be 3 x120 = 360 lower than the pressure
altitude. If air temperature is 5 C above standard then density altitude will be 600 feet higher than the
pressure altitude.
TIP:
Warm air is less dense air and thus density altitude is greater when the air is warm.
TIP:
The KLN90b GPS has a built in density altitude calculator. You can use it to get a more accurate density
altitude. The KLN90b in the piston simulators can be used just as well as the ones in the airplanes.
Page 22
Navigation for Professional Pilots
Sample Questions 2
1. The altimeter source altitude is 1000, altimeter setting is 28.92, temperature at 1000 feet is 15 C.
Calculate the pressure altitude (PA) and the density altitude (DA)
2. The altimeter source altitude is 7000, altimeter setting is 28.92, temperature at 7000 feet is 15 C.
Calculate the pressure altitude (PA) and the density altitude (DA)
3. The altimeter source altitude is 8500, altimeter setting is 30.86, temperature at 8500 feet is -
22 C. Calculate the pressure altitude (PA) and the density altitude (DA)
4. altimeter source altitude is 1624, altimeter setting is 30.35, temperature at 1624 feet is 18 C.
Calculate the pressure altitude (PA) and the density altitude (DA)
5. The altimeter source altitude is 1624, altimeter setting is 29.71, temperature at 1624 feet is 7 C.
Calculate the pressure altitude (PA) and the density altitude (DA)
Page 23
Navigation for Professional Pilots
This table is correct for an altimeter set with the Colesman scale on 29.92
The table shows that an altimeter “assumes” pressure will drop 1.10 inches of Mercury between
sea level and 1000 feet and then drop 1.06 between 1000’ and 2000’ etc. Consequently an altimeter set to
29.92 will read 7000 feet when the air pressure is 23.09 regardless of how high the airplane really is.
The Colesman scale on the altimeter simply “slips” the above scale to reset the zero point, as
shown in the diagram below, which is for an altimeter set to 30.44
Page 24
Navigation for Professional Pilots
This table is correct for an altimeter with the Colesman scale set to 30.44. When the actual air
pressure is 30.44 the altimeter reads zero.
Page 25
Navigation for Professional Pilots
IMPORTANT: altimeter settings are determined with an instrument located at the airport. Taking
the above table as an example, if a particular airport is at 3000 asl an altimeter adjusted to read 3000 at
that airport will “report” an altimeter setting of 30.44. The pressure difference between 3000 and sea level
shown in the above table (30.44 – 27.37) is only hypothetical. The actual sea level pressure may not be
30.44 on that day, but the altimeter will read 0 feet if the actual air pressure is 30.44. Since this is only a
hypothetical possibility it is not important. The thing to realize is that an altimeter setting permits the
altimeter to read the correct altitude at the airport (3000 in the example), because that is where the
altimeter setting instrument is located. Any temperature correction that an over flying airplane makes
need only be applied to the atmosphere between ground level and the true altitude of the airplane.
In the table above you can see that when the air pressure is 18.82 the altimeter reads 13,000 feet.
This will happen regardless of the true altitude. If the air pressure between ground level and 13,000 drops
exactly as shown in the table the altitude will be correct. More likely the pressure drop will vary from that
shown and thus the true altitude will not correspond to the indicated altitude.
If the air pressure declines with altitude more rapidly than the above table the true altitude will
be lower than the indicated altitude. This is very dangerous for any pilot flying in instrument conditions
and using the altimeter to avoid mountain tops.
Pressure decreases more rapidly in cold dense air. Thus we must correct for temperature error any
time the temperature is cold.
RAC 9.17 specifies our legal obligation to calculate a temperature correction. A correction is
required any time temperatures are significantly below standard. Normal practice among pilots is to make
a correction anytime ground temperature is 0°C or colder. Three methods of making the correction will be
presented in this course. In order of preference in use they are:
3. CR
RAC 9.17 recommends allowing 4% height increase for every 10°C below standard temperature.
This rule of thumb should only be used down to temperatures of -15°C. Memorize the rule of thumb and
be able to use it; the corresponding formula is:
The above formula gives the required correction, which should then be added to the desired
altitude to get the indicated altitude you will fly in order to be safe. Remember to keep ATC informed of
what altitude you are flying. This is particularly important if you will deviate from any specified altitude
such as a missed approach altitude or an altitude on a DME arc, etc. RAC 9.17 specifies that you should
also report deviations from FAF crossing altitude and MDA, but as these are minimum altitudes that you
Page 26
Navigation for Professional Pilots
can choose to be above on any approach most pilots do not report these deviations. However, you must
consider carefully whether any conflict with other traffic could result from your temperature correction
and keep ATC informed as necessary.
For temperature colder than -15°C use the table in the CAP GEN. This table can also be used for
temperatures of 0°C and -10°C; however it is based on an airport at sea level and therefore gives
conservative corrections for airports that are higher than sea level. If you use the equation above you get a
more accurate correction for airports that are above sea level. To use the table in the CAP GEN follow the
instructions provided with the table. Note that RAC 9.17 states that the table is not valid for heights more
than 5000 ASL. Many mountain approaches however have procedure turn and intermediate segment
altitudes higher than 5000 AGL. It is common practice among pilots to use the table by summing values,
for example adding 5000 and 3000 to get 8000. When doing this always round up each value obtained in
order ensure safety.
Page 27
Navigation for Professional Pilots
Performance Charts
You must master the use of all the performance graphs, charts, and tables in the C-172P POH, Beechcraft
Travelair Pilot Information Manual, and your Alsim (King Air) manual. Supplements to the C-172P POH are
found in Appendix 14 of your Program Manual. A complete explanation of how to use each chart, table,
and graph cannot be provided here, but most are self explanatory. Assignments are provided for you to
practice using these planning aids and to confirm that you are using them accurately.
The aviation Intranet provides links to many electronic aids that ease your flight planning chores, making it
possible to plan a flight in a much shorter time. You will be using these aids daily as you prepare for flights
but it is CRITICAL that you can perform the calculations without them should the need arise. Consequently
the assignments in this course – and the quizzes and exams – are to be completed without these online
aids, unless the instructions indicate otherwise.
Normal aviation industry practice is for flight departments to establish a cruise power setting and use it for
all but “special” flight situations. A special situation is one in which either an unusually long range is
needed, or an unusually high speed, or some other situation requires a non-standard power setting. For
example you might be asked to ferry an airplane over a distance that exceeds its normal range, but that
can be achieved if slower than normal speeds are used. Alternatively, you might be asked to brake-in a
new engine by operating it at 75% power for a certain number of hours. In such cases you must flight plan
for a power setting different from that normally used.
a. BE95
a. C-172 manual
Both these skills are vital. You will be given assignments to practice these skills, but if these are not enough
you must practice until you perfect the skill.
Practice these skills using the computer simulations provided for that purpose.
Page 28
Navigation for Professional Pilots
On our Intranet website several electronic aids have been provided. These electronic planning aids are
much quicker and easier to use than the paper products. They are similar to the professional flight training
aids used by modern airlines. You will use these electronic aids for your day-to-day flight operations in the
aviation program. For the C-172P you will find:
The Normal Takeoff distance graph is an electronic version of the two graphs in the C-172 Flight Planning
Supplement. It gives Normal Takeoff Distance, and Accelerate Stop Distance. It is much quicker and easier
to use, and always gives the correct answer. Use it prior to all flights to get your normal takeoff distance.
Use the tables on pages 5-12 and 5-13 when short field operation is called for.
The ENL has a built in weight and balance sheet, a cruise performance calculator, and a Navlog calculator.
The weight and balance calculator eliminates the need to use the charts in section 6 of the POH. The
navlog automatically determines TAS, CAS, IAS, rpm, eliminating the need to use any charts in section 5 of
the POH. It also calculates drift, groundspeed, ETE and fuel required for the flight i.e. it performs the
functions of a flight computer. Navlogs are covered later in this course.
TIP:
Remember that even though you will be using the electronic navlog for your day-to-day flying, which
makes things very quick, easy, and accurate, you must be able to do all the calculations long-hand when
needed. On your exams you will have to calculate without the electronic aid. When doing assignments you
should do all the calculations by hand and then use the electronic navlog to see if you made a mistake.
The ENL contains a weight and balance calculator for quick, easy and accurate weight and balance
calculations.
Page 29
Navigation for Professional Pilots
Most “good” grass runways require 25% more distance than a paved runway
90% - (headwind component / rotation speed)% = percent change in takeoff roll and distance to
clear obstacle. (e.g. 12 knot headwind and Vr = 94 therefore 90% - 12/94 = 77%
110% + (tailwind component / rotation speed)% = percent change in takeoff roll and distance to
clear obstacle.
In Avia 100 you will learn to use the above rules of thumb to make reasonable go – no go decisions in
tricky takeoff situations.
Page 30
Navigation for Professional Pilots
The above question is a Transport Canada favorite on the commercial pilot and ATPL exams. The solution
is quite simple if you remember the meaning of the concept known as moment. A moment is: weight x
arm. At present we know the moment of the airplane is:
The difference in moment, which is 1000 could be created by an infinite number of possible weight shift.
For example we could shift 1000 pounds forward 1 inch, or 500 pounds by 2 inches, etc. In this case we
have been told to shift 400 pounds of freight, so it must be moved 1000/400 = 2.5 inches.
An important point to notice is that it makes no difference what the current location of this freight is, only
that we move it forward at least 2.5 inches.
In summary:
Step 1: Calculate the current moment and desired moment, subtract to get the desired moment shift.
Page 31
Navigation for Professional Pilots
Here is a typical transport Canada exam question, choose the correct answer:
An airplane weighs 9000 pounds. The CG is 73 inches aft of the datum, The aft CG limit is 71 inches aft of
the datum. There is 600 pounds of freight at 104 inches aft of the datum. Shift this weight to at least:
a) 85
b) 75
c) 65
d) 55
M-change = 18000
The answer is therefore: 104 – 30 = 74. Most people will therefore choose b, but that is WRONG. If you
move the weight to arm 75 it is still one inch too far back. Since the next lowest option is 65 that is the
correct choice on this multiple choice question.
Page 32
Navigation for Professional Pilots
Page 33
Chapter 2
This chapter introduces you to the fundamental concepts of navigation. Everything in this chapter is vital.
If you don’t understand and retain it 100% there will be a problem, so review this material often.
1. Mass
2. Distance
3. Time
All other concepts from simple ones live velocity and acceleration to complex concepts such as work,
power, energy, etc. are all composites of these three concepts.
Even concepts that may not at first appear to be composites of the above three actually are, for example
temperature is really just a measure of the velocity of particles, which in turn is the composite of distance
and time.
Velocity is a vector quantity. In other words it has both magnitude and direction. The direction is imparted
to the velocity by the orientation of the distance. Think about what this means and we will discuss it in
class.
d = Vt
T = V/d
To be more precise Groundspeed and direction of flight are the fundamental concepts in navigation. Once
we know our groundspeed (GS) and track-made-good over the ground (TMG) we know everything we need
to know to predict the time it will take to complete a flight.
Unfortunately there is a confusing array of speeds that we must learn to sort through:
Navigation for Professional Pilots
You should already know that an airspeed indicator (ASI) does not show TAS.
What a pilot actually requires to fly safely is the Equivalent Airspeed (EAS.) An airplane always stalls at a
certain EAS, and we always fly our approach at a certain EAS. Think of EAS as the pressure you would feel
on your face if the airplane had an open cockpit.
Unfortunately airspeed indicators do not show EAS either, so we must learn to convert indicated airspeed
(IAS) to Calibrated Airspeed (CAS) and then to EAS and finally TAS.
In summary – life for pilots would be much better if there was only EAS and TAS. Unfortunately we must
learn to deal with the undesirable IAS and CAS
You can also determine TAS in flight by reading your IAS and applying correction for:
Compression error
Density error
Page 36
Navigation for Professional Pilots
Mathematically:
TAS = EAS/√σ [σ is the density ratio, i.e. density of air divided by sea level standard
density]
The good news is that there is usually not much difference between IAS and EAS. Most of the time it is
reasonable to assume that the indicated speed is the same as equivalent speed. At very slow speeds (high
angle of attack) there will be a significant error, and also at very high speeds and high altitudes, above 200
knots and 20,000 feet there will an error.
Indicated airspeed is by definition the speed shown on the airspeed indicator. Like any instrument and
airspeed indicator is imperfect and as such a calibration chart must be provided. The calibration chart is
found in the POH. The calibration chart compensates for the imperfect measurement of Pitot tube and
static port on the airplane. Once you apply the correction factor you will have calibrated airspeed (CAS.)
Most of the calibration error is due to the position of the static vent on the fuselage, therefore calibration
error is frequently called position error.
Calibrated airspeed is pretty close to equivalent airspeed in most cases. In fact the difference between EAS
and CAS is less than one knot for airplanes flying less than 200 knots and less than 20,000 feet. That covers
both the C-172P and Travelair. So, for these airplanes you may feel free to say that EAS = CAS.
Page 37
Navigation for Professional Pilots
For any airplane flying above 20,000 feet (which includes the King Air) it will be necessary to apply a
compression correction factor. Compression refers to the fact that air entering a Pitot tube is compressed
and thus its pressure rises; consequently airspeed indicators always over read. CAS is always more than
EAS. So an airplane flying at 250 KCAS at 30,000 feet is experiencing less than 250 KEAS.
Your CR flight computer automatically applies compression correction, if you use the “professional
method” for converting CAS to TAS. The “simple method” DOES NOT allow for compression error.
ICE-T
To convert from IAS to TAS it is necessary to apply the corrections in the proper order. Always convert IAS
to CAS, then CAS to EAS, then EAS to TAS. To remember the sequence, use the pneumonic ICE-T.
Remember that with the CR you go directly from CAS to TAS, but that is because the EAS compensation is
built into the computer. We cover use of the CR later.
Page 38
Navigation for Professional Pilots
Heading is expressed as an angle from north. Heading can be expressed in magnetic, true, or grid, but
always in units of degrees.
The earth spins around an axis that passes through the north and south poles. Straight lines drawn
between the poles are called meridians of longitude. These lines define true north. Meridians appear on
your map and you will learn to orient your protractor to these lines of longitude when measuring the true
track (TT.)
In the northern domestic airspace pilots set their heading indicators to true. In that case the headings
displayed on the heading indicator are true headings.
In the southern domestic airspace, pilots set their heading indicators to magnetic. The magnetic North
Pole is many miles from the real North Pole and thus there is a difference between magnetic headings and
true headings. The difference is called variation, and you will find it marked on your maps. We will be
covering map theory in detail later.
When flying over the poles neither true nor magnetic heading reference is satisfactory. In such cases
another reference system known as grid is used.
Compass Deviation
Like any piece of equipment a compass is never calibrated perfectly. The error in the compass is called
deviation. Each aircraft compass comes with a deviation card that shows the extent of the error. As a pilot
you must consult the deviation card and take it into account when setting the heading indicator to
correspond to the compass.
Imagine that your balloon rises a few hundred feet and then maintains that altitude. You follow it and
discover that it more-or-less drifts in a straight line. This is important because it will be difficult to flight
plan if air moves in random fashion. Fortunately it generally moves in a steady continuous fashion, at least
over a distance of a few miles. The primary complication in navigation planning involves allowing for this
movement of the air (wind) i.e. allowing for drift.
Wind is described by specifying the direction the air is coming from and how fast. When we say the wind is
north at 15 knots we are saying that it is coming from the north, i.e. moving south, 15 nautical miles every
hour. If you release your balloon into this air mass it will be 15 NM south after one hour, 30 NM south after
two hours, etc.
Page 39
Navigation for Professional Pilots
Most people find it pretty easy to visualize a balloon drifting in the wind. The main difficulty is in realizing
that wind is a large scale phenomenon not a stream within the air but the whole air. Do NOT think of wind
as something that happens in the air but as a property of the whole air mass you fly in.
While it is obvious that a balloon drifts it is equally true, if less obvious, that an airplane does also. An
airplane moves through the air, which a balloon does not, but the movement of the air (wind) adds to the
net movement of the airplane never-the-less. An airplane’s net motion is the sum of true airspeed and
wind. True airspeed is a vector quantity that expresses how quickly an airplane moves through the air, and
in what direction.
To explore the meaning of drift examine the simulation called Drift on the Intranet website.
GS = TAS + wind
All three of these entities are vectors. So, all we have to do is remember how to add two vectors.
When dead reckoning you start with a known true airspeed and a forecast wind plus a track you wish to
fly. Your task is to determine the heading that is required to maintain that track and the resulting
groundspeed (so that you can calculate time to destination.)
We will now learn the simplest method of solving the above problem. No calculators or mathematics is
required. We will simply draw a picture. But it must be an accurate picture so get out your navigation-ruler
and protractor and follow along.
For our first sample problem we wish to fly from airport A to airport B. The distance between them is 240
NM and the true track is 050°. The wind is from 270° at 20 knots. The airplane flies at a true airspeed of
100 knots.
1. Draw a vertical line roughly in the center of the paper which we will use to represent a meridian
of longitude (i.e. it represents true north.)
2. Make a small “x” in the lower left quadrant of the sheet to represent airport A. We put it in the
lower left quadrant because we are going to fly north-east so we want to allow room to draw the
line to airport B.
Page 40
Navigation for Professional Pilots
3. Center your protractor on airport A and orient it to north using the line of longitude. Mark 050°
and then draw a line from airport A in the direction 050°. At this point your paper should look like
the one below:
The line represents the track to airport B. We call this the track-made-good (TMG.) We don’t need to mark
on airport B.
4. Next we will draw a vector representing the wind. Place your protractor on the TMG somewhere
in the upper right quadrant. (When drawing TAS-Wind triangles always place the wind vector
near the destination end of the TMG.) Orient your protractor using the meridian and then mark a
dot at the center of your protractor and another mark at 270° (the wind direction.)
5. Take your ruler and laying it accurately from the wind dot to the 270° mark measure the distance
20 NM from the TMG in the direction of the wind. Your sheet should now look like the one below:
Page 41
Navigation for Professional Pilots
The most accurate way to perform the next step is with a measuring instrument known by geometers as a
compass. If you don’t have one it is possible to measure with a ruler, but it will likely be less accurate.
6. Set your measuring compass (shown above) to exactly 100 NM (the TAS.) Put the tip of the
compass at the beginning of the wind vector and draw an arc that intersects the TMG near
airport A. Your diagram should now look like the one below:
Page 42
Navigation for Professional Pilots
To work properly a TAS-Wind triangle must be drawn accurately. The TMG must be exactly 050°, the wind
vector must be exactly 20NM long and the arc must be exactly 100NM long. If these conditions are met
you will get an accurate wind triangle.
7. Draw a line from the point where the arc cuts the TMG to the beginning of the wind vector. This
line is exactly 100 NM long and it represents the true airspeed. The diagram is now complete, and
it should look like the one below:
Page 43
Navigation for Professional Pilots
The angle labeled (da) above is called the drift angle. The heading you must fly is represented by the TAS
vector and you can measure it with your protractor. If you drew your diagram accurately true heading is
042°, and drift angle is 8°.
Measure the distance from the arc to the point where the wind vector intersects the TMG. This represents
the distance flown in one hour – i.e. it is your groundspeed. The distance is 115 NM. We now have all the
items we set out to determine:
From this we can calculate the amount of time it takes to fly the 240Nm from airport A to airport B. It is
NOT necessary to draw the full picture but if we did it would look like the one below:
Page 44
Navigation for Professional Pilots
The purpose of the above diagram is to convince you that the net drift for the entire trip is proportional to
drift for one hour. The flight from airport A to airport B takes 2:05 during which time the airplane drifts a
total of 42 NM, which is represented by the line labeled “wind/whole trip” above. But, as you can see it is
in proportional to the length of the trip, so da is the same in both triangles.
Page 45
Navigation for Professional Pilots
The wind vector in the above diagram has been broken into two components, crosswind (XW) and tailwind
(TW) that are perpendicular and parallel to TMG respectively. It is critical to remember that XW and TW
are by definition relative to TMG not TAS, this is a common mistake. In slang pilots refer to tailwind as
“wind on the tail” which implies that it is relative to the airplane, but this is NOT correct. Tailwind,
headwind, and crosswind are all relative to the TMG, which is the course that is to be flown. To see an
active version of this definition examine the simulation called Crosswind, tailwind, tailwind, drift angle -
definitions on the Intranet website.
da = Sin-1(XW/TAS)
Groundspeed Defined
The following diagram extends the one above to define groundspeed (GS)
Page 46
Navigation for Professional Pilots
Note that TAS forms the hypotenuse of a right-triangle the base of which equals cos(da) x TAS. To this
value the tailwind must be added to get groundspeed. The formula is:
GS = cos(da) x TAS + TW
It is very worthwhile to realize that as long as da is small there is not much difference between cos(da) x
TAS and TAS. That is to say that cosine of a small angle is almost one. Thus when performing a quick
estimate of groundspeed it is usually acceptable to add tailwind directly to TAS, but to get the precise
value the cosine of drift angle must be applied. It is quite obvious that you can do this with an electronic
calculator, but the CR also makes this allowance as we will see.
Page 47
Navigation for Professional Pilots
The relative wind angle is the absolute value of the angle between the wind direction and the track made
good. In the example above the wind direction is 090° and the track made good is 050°. The relative wind
angle is therefore 40°. Once we know the relative wind angle the crosswind and tailwind can be calculated
by simple trigonometry as:
XW = sin(rwa) x Windspeed
TW = cos(rwa) x Windspeed
The above formulae can be used to determine crosswind and tailwind with an electronic calculator. The CR
flight computer performs the same calculation.
In the example problem the wind speed is 20 knots and the relative wind angle is 40° therefore XW =
sin(40) x 20 = 13 knots and TW = cos(40) x 20 = 15 knots. Using these values the drift angle and
-1
groundspeed can be calculated, as described above. Drift angle is da = sin (13/100) = 7° and groundspeed
is GS = cos(7) x 100 + 15 = 115 knots. Note that these values match the ones previously determined using
the TAS-Wind Triangle.
Page 48
Navigation for Professional Pilots
There are a few minor terminology differences between your CR manual and those used in this text. For
example TMG is the same as what Jeppesen calls true course (TC.) Jeppesen draws a distinction between
drift angle and crab-angle; we will use the term drift angle for both.
Read pages 30 to 50 doing all the sample problems (the short section on addition and subtraction on page
32 can be skipped.) Once you have worked through the CR manual try the following sample problems:
Sample Problems:
Given TAS, wind, and desired true course (TC) determine XW, TW, da, and GS:
80 120/25 090
80 120/25 210
Drift Estimation
The accurate mathematical calculation of drift angle and groundspeed as explained above can be
performed with an electronic calculator, a CR, a spreadsheet, or a computer program. However, when
flying it is often necessary to change course without the opportunity to accurately recalculate the drift.
Numerous IFR examples come to mind, for example when cleared to hold or to do an approach the pilot
must establish a designated course (TMG) or when the assigned route is changed drift must be determined
on the new route. In VFR flight you are already familiar with the need to plan a diversion should weather
Page 49
Navigation for Professional Pilots
or some other circumstance require you to change course. It is therefore extremely valuable to have a
technique for estimating drift and groundspeed using only mental calculation (estimations.)
Estimate XW and TW
The first step is to estimate crosswind and tailwind. You will need to know the magnetic wind. A good pilot
always knows the wind direction and speed. Remember that the upper wind forecast is in true, so you
must apply variation to get the magnetic wind.
To estimate crosswind and headwind use your heading indicator (HI) or preferably and HSI, as though it is
a CR. If your aircraft has an HSI set the desired course on the course-bar. Locate the magnetic wind
direction on the heading indicator and determine how many degrees from the nose or tail of the course
bar the wind is. The is the relative wind angle.
Page 50
Navigation for Professional Pilots
Page 51
Navigation for Professional Pilots
In the above diagrams it is assumed that the pilot turned so that the desired course TC or TMG is “on the
nose.” (This point is covered again below in the description of the simulation called Drift Estimation
Challenge.) If the wind is 30° from the course or tail then 50% of it is crosswind and 90% tailwind or
headwind. If the wind is 45° from the course or tail then 70% is crosswind and 70% is tailwind or headwind.
And finally, if the wind is 60° from the course or tail then 90% is crosswind and 50% is headwind or
tailwind. These percentages must be memorized.
If there is a 30 knot wind and 50% is crosswind and 90% is headwind then crosswind is 15 knots and
headwind is 27 knots. This example corresponds to a wind 30° from the course. Had the wind been 30°
from the tail (reciprocal of course) the only difference would be that the tailwind would be 27 knots. Use
this method to estimate the XW and TW for the following sample problems:
20 30 from course
20 45 from course
20 60 from course
30 30 from tail
30 45 from tail
30 60 from tail
40 On the course
40 On the tail
Note that when the wind is “on the nose” it is all headwind with zero crosswind. When “on the tail” it is all
tailwind with no crosswind. Similarly, if the wind is “on the wingtip” it is all crosswind with no headwind or
tailwind. It is crucial to realize that in this case we are using the word nose to represent the course, not the
heading.
Once we know the headwind or tailwind we can estimate the groundspeed by subtracting or adding to the
true airspeed. We learned previously that we should first multiply TAS by cos(da) but this typically makes
only one or two knots difference, so for estimation purposes we can say that GS = TAS + TW or GS = TAS –
HW.
-
It seems like it will be much more difficult to estimate da since we need to evaluate the equation da = sin
1
(XW/TAS). While this sounds impossible to do in your head there is a simple mathematical trick that
Page 52
Navigation for Professional Pilots
makes it quite simple. To explain we will review the definition of the angle unit called radians, and the
formula for circumference of a circle.
It is important to recognize the close relationship between arc-length and the subtended angle (ra.) The
angle ra can be precisely determined, in units of radians, by dividing arc-length by radius. To convert ra to
units of degrees multiply by 180 and divide by pi. This may not be sounding like something that will be easy
to do in your head but stick with me. Note that so far no approximations have been made, i.e. the above
definitions are precisely valid. Next we will look at how we can substitute the definition of the radian as an
approximation for estimating drift angle.
Page 53
Navigation for Professional Pilots
Examine the diagram above that redefines XW as the wind component perpendicular to TMG. The point to
notice is that the length of XW is very nearly the same as the length on an arc drawn from TAS to TMG. For
small values of da it is reasonable to say that acr-length = XW. That being the case da in radians equals
XW/TAS. Since we want da in units of degrees the formula becomes:
You may be thinking, “This still doesn’t seem too easy to do in my head.” There is one final step that
transforms the above equation into a simple method; it is called the “Magic Number.” Since TAS is the
same from day-to-day we can calculate the value TAS time pi divided by 180 and memorize this number,
we call it the magic number. Once you know the magic number for your airplane drift is easy to estimate,
it is simply:
da = XW / Magic Number
Magic Number
Magic number was introduced in the previous section. Magic number is simply TAS x Π / 180 i.e. TAS /
57.3. It is important for you to memorize the magic number of the airplanes you fly. It is helpful to know
Page 54
Navigation for Professional Pilots
your magic number for both cruise and hold/approach speeds so that you can estimate drift in cruise as
well as holds and approaches. Since magic number is used for estimations there is no sense in calculating it
overly accurately. For true airspeeds up to 180 KTAS determine magic number to the nearest ½, above 180
KTAS determine magic number to the nearest whole number. In the table below some magic numbers
corresponding to the C-172, Travelair, and King Air have been left blank for you to fill in, other examples
have been provided:
If you are flying a Piper cub with a 20 knot crosswind drift is 20°, what would it be in a King Air. The answer
is 5° (20/4.) What would drift be in a jet airliner with a magic number of 8? The answer is 2.5° (20/8.)
Page 55
Navigation for Professional Pilots
1 25
1 30
2 20
2 30
2 45
3 25
4 30
6 30
8 30
Two-bit Math
The magic number of a Beech 95 in cruise is 2.5, therefore drift equals XW/2.5. You may find it challenging
to divide by 2.5 in your head but there is a simple trick that makes it easy. Answer the following question:
You go to the 7-11 store to by a snack for $1.67. You reach into your pocket and discover you have a bunch
of quarters. How many do you give the clerk?
You probably had no trouble realizing you needed seven quarters to pay for your snack. You do this
particular calculation so often that it seems trivial to you, but you have actually just divided 1.67/0.25. You
would have freaked if I had asked you to divide 1.67 by 0.25 in your head, but it seemed simple when you
think of it as money. You most likely just remember that each dollar is four quarters and you know that
one additional quarter covers items up to 25 cents, two are required for items up to 50 cents, and three for
items up to 75 cents. Anything over 75 cents would have required an eighth quarter. And so on.
Now compare the above calculation to the one you wish to do in your head XW/2.5. This is the same as
saying (XW/10)/0.25. Of course dividing any number by 10 is very simple since all you have to do is shift
the decimal one place left, for example 20/10 is 2, 33/10 is 3.3, etc. Can you see how to use this trick to
estimate drift angle? Simply take the XW and divide it by 10, then think of the result as the price of your
snack and pay for it in quarters. For example if the crosswind is 15 knots, that becomes $1.50, which will
take six quarters; therefore da = 6°. Try the following examples for yourself:
Page 56
Navigation for Professional Pilots
2.5 10 $1.00 4
2.5 15 $1.50
2.5 17 $1.70
2.5 20
2.5 22
2.5 24
2.5 28
2.5 32
2.5 36
Page 57
Navigation for Professional Pilots
The drift estimation techniques from this simulation combined with the bracketing technique in the next
simulation will give you all the skills you need to efficiently navigate IFR.
Page 58
Chapter 3
Introduction to Radio Navigation
In this section you will learn how VOR, ADF, DME, and GPS work. These radio aids are used to guide pilots
during the enroute phase of flight.
When doing radio navigation a VOR, ADF, or GPS is used to define a track over the ground, i.e. the desired
course (TC, or TMG.) Once a course is established drift theory, covered above, applies. Your task is to
calculate the heading that will keep you on course and the groundspeed. It is important to realize that
there is no difference at all in the objectives or methods of flight planning for IFR flight and VFR flight.
It is important to have a basic understanding of how VOR, ADF, DME and GPS work. On the Intranet, under
Sim-Multimedia there are several interactive tutorials covering: “How VOR Works” “How ADF Works” and
“How DME Works.” You will find further clarification about how DME works by reviewing the simulations:
“DME Jitter” and “Squitters, and Auto-standby.” AFTER you have reviewed all the simulations continue
with the following.
Read all of section 2 (Navigation Systems) in your Instrument Procedures Manual before continuing; this
will explain all the navigation aids.
On the KLN-90B GPS (in the B-95 and piston simulators) the map “super-nav 5 mode” can be set to VOR
TLH. T stands for terminal VORs, which are the ones between 108.00 and 111.85. L stands for low altitude,
which are all the VORs on Victor airways (see LO charts below.) H stands for high altitude, which are all the
VORs used on high altitude airways (see HI charts below.)
Between 108.00 and 111.75 those frequencies in which the first digit after the decimal is odd are ILS
frequencies, while those where the first digit is even are VORs. From 112.0 to 117.75 all frequencies are
VOR. To help you grasp what I mean look in your CAP and write down the frequencies for the following ILS
transmitters:
Navigation for Professional Pilots
Victoria (CYYJ) 09
Victoria (CYYJ) 27
Abbotsford (CYXX) 07
Kelowna (CYLW) 16
Calgary (CYXC) 28
Calgary (CYXC) 34
To confirm your understanding of the frequency allocation system complete the following table:
109.15 ILS
111.30 ILS
107.55
111.60
Page 60
Navigation for Professional Pilots
115.30
117.95
109.85
112.15
114.70
There are a total combined 200 VOR and ILS frequencies, 40 ILS and 160 VOR. Because of the numbering
protocol there are two VOR frequencies then two ILS frequencies, etc. up to 112.00.
DME channels are numbered according to the military TACAN channel. There are more TACAN channels
than VOR channels so the first DME channel used in civilian flying is 17 and TACANs 57 to 66 inclusive are
not used either. DME channels alternate between X and Y, with X channels corresponding to VOR and ILS
frequencies that end in decimal 00 while the Y channels correspond to VOR and ILS frequencies that end in
decimal 05. Operationally there is no difference between an X channel and a Y channel – both transmit
squitters on the same frequency but listen for interrogation on different frequencies therefore they will
interfere with each other and must not be used in the same area. By convention, on LO charts and in the
CAP the X is dropped from DME channels – only the Y is shown; for example YVR frequency 115.9
corresponds to DME channel 106X, but if you look on the map it just says DME Channel 106. But ILS 26R is
frequency 111.95, which corresponds to DME channel 56Y, which is shown on the charts.
There is no reason to memorize the DME channel assignments although you should understand how the
frequencies are assigned. It is important to realize that a specific DME channel always goes with a specific
VOR / ILS frequency and that is how your Nav radio is able to tune the DME without you needing to input
the DME channel. The complete list is found in your CFS section D2.
In the diagram that follows no shadow effect is considered, but in reality if the VOR signal is blocked by
building, mountains, etc the reception range will be less than indicated by the formula.
Page 61
Navigation for Professional Pilots
In the diagram it is clear that the aircraft’s altitude plus the radius of the earth forms the hypotenuse of a
right triangle with r and distance from VOR (s) as the other sides. Using Pythagoras’ theorem and solving
for s results in an equation. But actual reception range is not zero when at ground level. Thus the
recommended formula is:
To receive a VOR you must be within the slant range (s) given by the equation above. A few sample values
are:
1,500 50
5,000 87
10,000 123
Page 62
Navigation for Professional Pilots
An ADF, if working properly, always points at the station. It does so even if the heading indicator is set
incorrectly. As a result you will be flying on the WRONG course if your heading indicator is not accurate.
On the other hand, you can always find your way to the station even with a failed heading indicator, which
you cannot do with a VOR. The bottom line for pilots is to know and understand the differences between
VOR and ADF in normal and heading-reference-failed modes of flight.
Usually you use your ADF radio with non-directional beacons (NDBs) but it can also tune commercial AM
radio stations. The ADF in Selkirk College airplanes can tune frequencies up to 1200 (higher bands are not
useable.) A complete list of every radio station in Canada is on page D27 of your CFS.
It is important to know that DME gives “slant-range” which is the actual distance from the airplane to the
DME station. When you fly over the station a DME shows your altitude in nautical miles. Because of the
slant range error groundspeeds calculated by a DME are not accurate when close to the station. The rule
of thumb is to consider DME based groundspeed accurate only when distance from station in nautical
miles is greater than altitude in thousands of feet. In other words, if you are at 4000 agl you need to be at
least 4NM away to get an accurate groundspeed, but if you are at 40,000 feet you need to be 40NM away
to get an accurate groundspeed.
There is a simulation on Intranet that fully explains the indications of the various navigation displays you
will encounter in this program. It examines the most common navigation indicators:
Page 63
Navigation for Professional Pilots
Each navigation display has its advantages. You will learn what each of these indicators looks like, what it
displays and what it doesn’t. You will see for example that as wonderful as an HSI is it doesn’t work with
ADF. You will also see that while an RMI is a great thing to have, it doesn’t work with ILS, etc.
In the following description of the Nav Displays simulation marker beacons and ILS is mentioned for
completeness. The theory of their operation is not part of this course. They will be covered in Avia 260.
GPS Navigation
The basic operating principles of GPS are explained in a slide-show on our Intranet. The link can be found
under Avia 100, Avia 160, and Avia 260. Read this entire slide show before continuing. Also read section
2.2 (Navigation systems) in the Instrument Procedures Manual.
An important thing to realize is that a properly functioning GPS is a very accurate source of time. Pilots
should always set their clock (watch) accurately for IFR flight, and your GPS is a legal source of accurate
time. Take every opportunity to set your watch to the GPS in the airplane. (Note: the GPS in the simulators
does not give accurate time.)
When using VOR and ADF navigation accuracy is greatest close to the stations and less accurate farther
away. Since GPS has no stations, the accuracy of GPS is the same regardless of where you are on the
airway. Consequently GPS is more accurate than VOR or ADF for the enroute phase of flight.
A major problem with GPS is that it can fail in certain ways without giving a warning to the pilot. RAIM is
one method of improving warning that a failure has occurred. You will learn all the legal requirements for
RAIM in Avia 120 and 220. This material is also covered in the readings assigned above.
Distance values displayed on a GPS are horizontal, i.e. they are NOT slant range. Thus GPS gives accurate
groundspeed even when close to “the station” (of course there really is no station, so this is obvious when
you stop to think about it.)
GPS gives distance off track rather than angle off track (VOR and ADF give angle off track.) There are pros
and cons to this and you MUST learn to translate between both in your mind (more on that later.)
Bracketing
It might not seem so at first but radio navigation can be done in accordance with the principles of DR or
pilotage. When we defined these terms (review if you don’t remember the meanings) we said that DR is a
more sophisticated form of navigation. Sadly, many pilots use pilotage anyway. Pilotage in terms of VOR
or ADF navigation means “chasing the needles.” If you simply turn so as to push the needle back where it
belongs (centered for a standard VOR indicator) you will stay on course, but you won’t determine the
heading that keeps you on track and will thus tend to chase wildly back and forth when you get further
from the station where the signal is less sensitive, and you will also have a very hard time avoiding wild
swings in close proximity to the station where the needle can move very quickly due to increased
sensitivity.
Page 64
Navigation for Professional Pilots
The secret to avoiding needle chasing is to use a technique called Bracketing. This is covered in a
simulation on the Intranet.
In the previous simulation we learned to estimate wind drift based on the forecast wind. This is an
invaluable technique and one you should use every day as an IFR pilot, but it can only get you roughly to
the correct heading. Because winds aloft forecasts are not perfect you will need to adjust your heading
enroute until you find the exact amount of drift. The technique used to find the exact amount of drift is
called bracketing.
In the simulation, just to make things more challenging, you are not given any wind information at all. You
will see that even in this worst-case scenario you can use bracketing to figure out drift.
Sadly many IFR pilots never master bracketing. They just wallow around the sky chasing needles back and
forth. But, you won’t be one of those guys, will you?
To master bracketing one thing that is needed is to fly precisely, so you can observe which way the
airplane is drifting. In the simulation flying accurately is easy, in the real world it can be more challenging,
although it is easy if you use the autopilot. When you fly the airplane you must try to fly headings as
precisely as possible. If you can’t fly precisely you won’t be able to take full advantage of the procedures
you are learning in this course.
The other thing you must do when bracketing is remember what headings you have been flying. It should
be pretty easy to remember them, but for the first few times through this simulation you might like to have
a pad of paper and write down what you have done. Examining a written record of the headings you have
flown will show whether you are “zeroing in” on the required heading, or wallowing.
There are several secret codes built into this simulation. The main ones are:
A = All
H = HSI
R = RMI
You may choose any navigation display you wish. However, I recommend that you start with HSI or ALL, as
these are easier to see drift on.
Page 65
Navigation for Professional Pilots
The following explanation will take you through a tutorial using the Bracketing simulation – please
complete this section while using the simulation.
The secret code places the airplane on course 090, 12 miles west of the navaid. Set time compression to 1X
unless you have a very slow computer. The flying instructor is flying. Read the “instructors mind” (the
green box at the lower right.) Initially it says that the instructor is evaluating the heading 090. I.E. the
instructor is waiting to see which way the airplane will drift.
Pretty soon the instructor sees that the needle is moving left (picture above.) Therefore he knows that 090
is too far right. Whatever heading is needed to stay on course it MUST be less than this heading.
The “instructor’ mind” says 090 is the maximum heading he will ever fly. We call this the right hand
bracket.
Tip: as you observe the simulation you should press the 2-key to restart the sequence if it gets ahead of
your reading.
Tip: set time compression to zero to freeze the motion after each turn the instructor makes, so you can
keep up with the process.
The instructor has begun searching for a left limit (see comment in instructor’s mind.)
Page 66
Navigation for Professional Pilots
Here is what you will see. First the instructor turns 5 degrees left. He then waits to see what the needle
does.
The IMPORTANT point is that it only matters WHICH WAY THE NEEDLE IS MOVING. So, the instructor flies
heading 085 for a few seconds until he realizes that the CDI is still moving left.
Next he tries heading 080, but the needle still moves left. So, he tries 075. All this time the instructor’s
mind says, “searching for left limit.”
The needle still moves very slightly left on heading 075, so the instructor tries heading 070.
After a few seconds on heading 070 the instructor sees that the CDI has begun to move to the right.
If you miss part of process, or just want to see it happen again, either press the 2-key again, or click the
“Start Over” button.
Minimum: 070
Evaluating: 080
Maximum: 090
Page 67
Navigation for Professional Pilots
Comments:
Left-limit established
If it doesn’t say the above you need to give the instructor a few more seconds to think, so increase time
compression until he has time to think, then return time compression to zero.
Reading the instructor’s mind you now see that he realizes that heading 070 is less than the heading that
WILL be required to stay on course. His mind now states that the minimum heading will be 070. This is
called the left hand bracket.
NOTE: The instructor will remain on heading 070 until the CDI re-centers.
NOTE: Whenever the airplane is off course always fly the corresponding bracket heading until back on
course.
1. The instructor realized the airplane was drifting right on heading 090, so he established 090 as
the maximum heading (right hand bracket)
2. After searching, the instructor discovered that 070 was the first heading to the left that caused
the CDI to move to the right. So, he establishes 070 as the minimum heading (left hand bracket)
Based on the above, the instructor knows FOR SURE that the required heading to keep on course is
between 070 and 090.
Note that whenever the airplane gets off course the instructor will always go to (but NEVER beyond) the
brackets – and will hold that heading until the airplane gets back on course. This commitment prevents
wild chasing of the needle back and forth (a common mistake of new IFR pilots.)
A really good pilot could tell from all that has happened so far that the correct heading is closer to 070
than 090 (see comments below about “beating” the computerized flying instructor.) However, the
instructor is programmed to just split the bracket into half. In this case the brackets are 070 and 090 so the
instructor decides that when he gets back on course he will try heading 080. In his mind he indicates 080 as
the heading he is evaluating.
Page 68
Navigation for Professional Pilots
The instructor remains on the left bracket (070) until back on course, and then tries heading 080 to see
what happens:
Watch the instructor. He will fly heading 070 until he gets back on course. As soon as he is on course he
will turn to the evaluation heading, 080.
Set time compression to zero once the instructor gets to heading 080.
Now read the instructor’s mind. He still states that the brackets (minimum and maximum) are 070 and
090. The comment in his mind says that he is “trying evaluation heading.” i.e. he on course and flying
heading 080.
1. The CDI does not move, indicating that 080 is the required heading.
2. The CDI moves right, indicating there is less than 10-degrees of drift.
3. The CDI moves left, indicating there is more than 10-degrees of drift.
Increase time compression from zero to see what happens. See how long it takes for you to realize the CDI
is moving.
After a few seconds the CDI moves a bit to the left. The instructor immediately turns to his left bracket
heading of 070.
First, notice that as soon as the instructor realizes he is drifting off he turns to the bracket heading (but not
beyond the bracket.)
The instructor now realizes that 080 is not the correct heading to stay on course. In fact he now knows, for
sure, that the CDI moves left on heading 080. So, he revises his maximum heading (right hand bracket) to
080 (From now on, even if he gets left of course at some point there is no need to fly a heading more than
080.)
Read the instructors mind. The revised brackets are 070 and 080. So, he chooses the midpoint, 075, as the
heading he will evaluate next, once he is back on course.
Page 69
Navigation for Professional Pilots
After a few seconds on the left bracket (070) the CDI is again centered and the instructor turns to heading
075. His mind now says that he is evaluating heading 075 (i.e. guessing that there is 15-degrees of drift.)
After one bracketing cycle the brackets have been reduced from a 20 degree span to 10 degrees. Can you
now see how things keep going? Each time we evaluate a heading we reduce the span of the brackets in
half. Soon they will span only 5 degrees, then 2½ (in theory.)
Usually there is no practical need to get the brackets closer than 5 degrees to each other, although the
instructor will keep going as far as he can.
Now the instructor is flying heading 075. The same three possibilities exist:
1. The CDI does not move, indicating that there is exactly 15-degrees of drift.
2. The CDI moves right, indicating there is less than 15-degrees of drift.
3. The CDI moves left, indicating there is more than 15-degrees of drift.
The brackets are at 070 and 080 respectively. So no matter what happens we will have narrowed down the
drift to a five-degree range. If the CDI moves left the brackets will again be adjusted, becoming 070 & 075,
if it moves right the brackets will become 075 & 080.
The CDI remains centered for a long time. This tells the pilot that the drift MUST be very close to 15
degrees. Eventually the CDI starts to move right, slowly. This tells the instructor that there is less than 15
degrees of drift.
A wise pilot would take the amount of time it took the CDI to move into account and revise the drift
estimate to 14-degrees. See comments below about beating the computerized flying instructor.
The computerized flying instructor is a stickler for purity so he revises the brackets to 075 and 080 and
revises his drift estimate to 12.5 degrees (heading 077.5.)
He now turns to his right bracket heading of 080 to get back on course and then tries heading 078.
Once the airplane is within a mile of the station it is best to STOP bracketing and simply fly the evaluation
heading until a mile beyond the station.
Increase time compression and watch the instructor fly past the station.
Page 70
Navigation for Professional Pilots
Theoretically the process continues exactly the same on the outbound leg. However, because you usually
are slightly off course (just a few feet, we hope) at station passage it is wise to “open up” the brackets
slightly once bracketing begins again on the outbound leg. The computerized flying instructor is
programmed to open the brackets by +/- 3-dgrees. Outbound bracketing then continues exactly as before
If you use bracketing faithfully you can establish drift within one or two degrees in short order. After that
all you have to do is maintain heading accurately and you have things made..
Repeat secret code 2 as many times as you need to until you fully understand all the logic of bracketing.
Make liberal use of setting time compression to zero, usually after each turn, so you can think about what
the logic is.
Try secret coed 3, 4, and 5 for more practice. All the computerized flying instructor to demonstrate if you
like.
If you “blow” a particular attempt use the “Start Over” button to try again.
You can click the “You have control” button at anytime to have the computerized flying instructor take
over and demonstrate the procedure to you.
If you followed the advice above you started by practicing bracketing with an HSI. However, you MUST
master bracketing with:
RMI
Press the S-key to switch to standard VOR indicator and practice bracketing.
Press the F-key to switch to Fixed Card Indicator and practice bracketing.
I fully expect that you will spend several hours with this simulation before you are comfortable with
bracketing, but it will be time very well spent.
Page 71
Navigation for Professional Pilots
By default the wind is hidden but all the other visual aids are visible. However, most airplanes don’t have
moving map displays, so you need to be able to navigate with only “raw” navigation data. So, click the
“Hide All” button at the bottom of the simulation to make the process more challenging.
Include Outbound
By default the computer generates inbound bracketing exercises. However, if you check the box at the
lower left of the simulation the computer will randomly include some outbound bracketing exercises for
you.
As you have seen, there is no real difference between bracketing inbound and outbound, but you should
still do some outbound bracketing practice.
In secret code 2, above, when the instructor tries heading 075 and the CDI doesn’t move for a long time
any human would realize that the drift is close to 15, and would only revise the heading to 076. Similarly a
human would move the left bracket NOT from 070 to 075 but only to about 073 (or so.) Review secret code
2 above until what I have said here makes sense.
The point is that you don’t always have to divide each bracket exactly in half. Use common sense
(something the computerized flying instructor never does.)
Break-out Logic
A FUNDAMENTAL principle of bracketing is that you commit to NEVER fly outside the brackets. This
prevents the wild chasing of the CDI or RMI needle that commonly plagues new IFR pilots.
The idea of bracketing is that you always have two brackets in mind that you KNOW FOR SURE make the
CDI move left and right (but only just.)
But, if the wind changes, or your heading indicator precesses, the brackets won’t work anymore.
IMMEDIATELY that you notice you are off course always turn to the relevant bracket heading. Within a few
seconds the CDI should start to slowly come back to center. If it doesn’t what do you do?
If precession is not the culprit then there are only two possibilities:
Page 72
Navigation for Professional Pilots
If you have no reason to believe the wind changed then test the navigation radios. Check the Morse code
identifier to make sure the station has not gone off the air. If the radio has a test button press it. (For
example the ADF radio can be switched from ADF to ANT then back to ADF. See if that changes the
indication. For a CDI turn the OBS a few degrees, then reset the OBS.)
ADF is particularly prone to giving false indications so if you have no reason to believe the wind has
changed just keep flying your heading for a minute and see what happens. Usually the false indication will
go away and you will see that you were on course the whole time.
VOR and ILS are much less likely to give false indications, although it is amazing how many ILS approaches
have bows in them caused by electronic interference on the ground.
Once you determine that the off course indication is real, if your bracket heading does not center the CDI
you must CHANGE the bracket. In computer programming this is called breakout logic. The computerized
flying instructor has breakout logic. If he flies the bracket heading for 30 seconds and does not get at least
0.25 degrees closer to course he moves the bracket out by three degrees.
The question is, when you move the bracket should you change the evaluation heading? That depends on
what you think caused the problem. If it was a wind shift then you should change the evaluation heading
in the same direction you opened the bracket, but half as much. If you think the problem was a temporary
navigation signal deflection then don’t change the evaluation heading, also stand ready to close the
bracket back in to where it was before.
Bracketing Summary
Bracketing is a fundamental tracking procedure. In this simulation the bracket always starts from the zero
point, with a totally unknown wind. In the real world you should always know roughly what the wind is.
Therefore you start with your best estimate of the heading to stay on course, using the technique of drift
estimation covered earlier. Then you set your initial brackets at +/- 10-degrees from there. With this head
start you should have a near perfect heading bracketed out within a couple of minutes.
If you start with a +/- 10-degree bracket it should only take a minute until you can tell whether you need to
adjust your evaluation heading left or right. When you do, move the bracket in, but NOT all the way to
your original evaluation heading. Pretty soon you will have adjusted your heading and brackets so that you
have two brackets about +/-5 degrees from your best estimated heading. You then react to even small CDI
deflections by turning to the appropriate bracket immediately. Using your judgment you revise your
estimated heading, tweaking it one degree at a time. Note: you can only tweak the evaluation heading
one degree at a time if you can fly your heading accurately enough to make such judgments.
Page 73
Navigation for Professional Pilots
Because bracketing is so powerful you can easily see that when combined with the drift estimation
technique covered earlier you can perform very accurate DR radio navigation even in the absence of
completely precise wind forecasts.
DME arcs are used on many IFR approaches and terminal arrival procedures. They allow airplanes to get
lined up for approaches without the high workload (for controllers) of radar vectors.
DME arcs are normally flown using an RMI. Therefore the simulation includes an RMI. The navigation
display also includes an HSI, a standard VOR indicator and an RMI. If an airplane has an HSI but no RMI
you can still do an arc by manually turning the HSI to keep it centered, so that it acts like an RMI. If you
have neither RMI nor HSI it is not good practice to fly DME arcs. I have not provided the option for doing
arcs without an RMI in this simulation.
DME arcs can be assigned at any distance from a DME station from 7.0NM up. Smaller arcs are never
used.
To fly an arc you must first fly a path that crosses the arc. The simplest way to do this is to fly directly
toward the VOR until you reach the desired distance to arc. Another common way is to be vectored until
you intercept the arc.
Once you intercept the arc turn so that the RMI needle points at the wingtip. If you are arcing right, that
means the RMI points at the right wingtip. A left arc means the RMI points at the left wingtip.
The easiest way to explain arcing is through an example. Please load the simulation and follow along with
the example below.
This simulation is for practicing DME arcs. You can also fly arcs using the Alsim simulation, but it is best to
master this simulation first.
“Pilot 200, you are cleared for a practice DME arc. Intercept the 8 DME arc from the 120 radial and arc
counter-clockwise to intercept the course 180. Your lead radial will be 014.”
Page 74
Navigation for Professional Pilots
The picture below shows the computerized flying instructor about half way through complying with this
clearance.
Let’s start by breaking down the clearance to make sure we understand it.
8 DME arc means that the airplane must fly a circular orbit around the VORTAC at a distance of 8.0 Nm.
(Indicated on DME radio.)
From the 120 radial means that the arc starts at the 120 radial
Intercept course 180 means that the objective is to wind up flying inbound on the 000 radial.
Lead radial will be 014 means that when the airplane crosses the 014 radial it will be 2 NM from the
assigned course. Think of lead radials like a wakeup call. When you get to the lead radial you are almost at
your assigned course, so you generally stop arcing and turn to intercept the assigned course (at 45°.)
Watch the Flying Instructor demonstrate the arc. (Press the 1-key to restart if necessary.)
Initially the airplane is flying outbound along the 120 radial, which is the designated start radial. (Later we
will do an example where the airplane flies inbound on the 120 radial.)
Page 75
Navigation for Professional Pilots
The instructor’s mind can be read at the lower right. He states that he intends to lead the turn onto the
arc. He plans to turn when the DME reads 7.2 (the value will be different if you chose a cruise speed other
than 150 KIAS.)
The above diagram shows that the turn to intercept an arc should start at a distance equal to the radius of
turn of the airplane. Assuming that the turn will be at rate one a simple mathematical formula for radius
of turn can be derived:
R = Groundspeed / 200
In other words:
r = .5% of Groundspeed
For example an airplane flying 156 Knots groundspeed would need to lead the turn by about .8 Nm. (1% =
1.6 Nm, so ½% is about .8 Nm.)
Keep in mind that the airplane must be in the turn at the designated distance. Allowing about six seconds
to get up to rate one turn, you should add an extra 0.1 to 0.2 to the calculated value.
In this demonstration the wind is zero, so the groundspeed equals the TAS.
At the calculated lead distance the instructor starts his turn. The pilot must turn so that the RMI is on the
left wingtip. Simply look at the tip of the RMI needle and turn 90° from that. In the example the RMI points
to 300 so the first heading must be 300 + 90 = 390 degrees – but that is 030.
Watch the flying instructor. At 7.2 Nm he makes a left turn to heading 030. If the lead was correct the
DME should read 8.0 Nm as he rolls out on that heading.
Page 76
Navigation for Professional Pilots
The only instruments needed to arc are the RMI and DME.
To understand an arc you must remember what your high school math teacher taught you; a line tangent
to a circle is always at right angles to the radius. Consequently the RMI needle, which shows your radial,
must always be at or near the wingtip when flying an arc. In this case we are flying a counter-clockwise arc
so the RMI needle must point near the left wingtip.
In zero wind all you need do, in theory, is keep the RMI needle on the wingtip and the DME will not change.
The airplane would fly a perfect arc. Unfortunately it is not possible to do such a perfect arc. Therefore, we
use a technique of making a series of short straight legs that approximate the arc. Watch the flying
instructor fly the demonstration and note how it is done.
The instructor turns so that the RMI needle is five degrees ahead of the left wingtip. He then maintains a
constant heading until the RMI needle drops to five degrees behind the wingtip. He then turns 10 degrees
left, bringing the RMI needle five degrees ahead of the wingtip again. This pattern repeats over and over.
The instructor constantly monitors the DME. If the airplane gets a bit wide (DME reads 8.1 or more) he
turns so that the RMI needle is MORE than 5 degrees in front of the wingtip. As long as the RMI needle is
kept in front of the wingtip the airplane will move in, closer to the VORTAC. If the DME is remains at
more than 8.0 as the RMI needle approaches the wingtip the instructor will turn to keep the needle ahead
of the wingtip.
If the DME drops to 7.9, the instructor realizes that he is inside the designated arc. Correcting this is
simple. Just like a rock on the end of a string moves out instantly if you let go of the string the instructor
realizes that if he simply stops turning, (i.e. maintains whatever heading he is on) the airplane will move
out on the arc. As this happens the RMI needle will move past the wingtip. Once the needle is below the
wingtip DME will start to increase. Once the DME reaches 8.0 the instructor resumes the usual arc
procedure by turning to bring RMI needle near the wingtip again.
The HSI and OBS are not needed to fly the arc. Therefore, once the airplane is established on the arc the
instructor will set the HSI to the assigned course (180 in this example) and set the OBS to the lead radial
(014 in this example.)
With the HSI set the pilot can visualize how the arc is going. The airplane will be slightly more than 90-
degrees from the final course when the lead radial is reached, and that is easy to see on the HSI. The #2
CDI will center as the airplane crosses the lead radial. (Prior to reaching the lead radial the CDI always
deflects to the center of the arc.)
Page 77
Navigation for Professional Pilots
As the airplane crosses the lead radial the instructor will STOP arcing and turn to make a 45-degree
intercept of the assigned course. He simply holds the 45-degree intercept heading until on the course, then
tracks inbound using the usual bracketing technique.
Whenever the RMI needle is ahead of the wingtip there is a small DME groundspeed. Common sense tells
us that we are “cutting in” on the arc, and DME is telling you how quickly.
Whenever the RMI needle is behind the wingtip there is a small DME groundspeed. In this case we are
moving away from the DME station at the indicated rate.
An important to rule to note is that if the groundspeed is decreasing the airplane is getting closer to the
VORTAC. If the groundspeed is increasing the airplane is getting further away from the VORTAC. These
statements are only true if the airplane is flying straight (i.e. not turning.)
Press the 1-key, again. Then press the “I Have Control” button.
Now it is your turn to fly the arc. Practice the procedure until you can keep the DME within 0.1 of the
assigned value. You will find it impossible to prevent 0.1 variations, but you should not permit 0.2
deviations from the assigned DME.
Tip: remember to set the HSI to 180 and the OBS to 014 once you are established on the arc.
The assigned practice arc is exactly the same as the previous one. The only difference is that this time the
airplane is flying inbound to the arc along the 120 radial.
Once again the instructor calculates that 0.8 Nm lead is needed, so he starts the turn at 8.8 Nm. As before
the first turn is to heading 030.
Press the 2-key, again. Then press the “I Have Control” button.
Now try the intercept from outside the arc on your own.
Page 78
Navigation for Professional Pilots
This time the same arc clearance is issued, BUT the difference is a 30-knot west wind.
From the map you can see that the wind is going to blow the airplane wide on the arc. What adjustments
to the previous procedure will be needed?
First notice that the groundspeed as we fly along the 120 radial is almost 180 knots. So, we must lead the
turn to the arc by 0.9 Nm this time (these values will be different if you chose a different cruise speed.)
A wise pilot would realize that the first heading should not be 030, because of wind drift. But, the
computerized flying instructor has not been blessed with common sense. Watch and see what happens
when he turns to 030.
As the airplane is blown wide on the arc the instructor sees the DME reach 8.1. At that point he turns to
move the RMI needle 10 degrees ahead of the wingtip. He then monitors the DME. If the distance does not
decrease he turns to move the RMI needle further in front of the wingtip. Eventually he discovers an
amount that causes the DME do decrease. He then keeps turning to maintain the RMI needle ahead of the
wingtip until the DME returns to 8.0
In the previous example, when the wind was zero, we saw that the closing speed was zero when the RMI
was exactly on the wingtip. But, in this case the closing speed is zero when the RMI is slightly ahead of the
wingtip. And, the “zero point” changes as the airplane proceeds around the arc, because the angle the
wind makes to the arc keeps changing.
A wise pilot would use this information to arc better. Rather than using the wingtip as the zero reference
use the point where the groundspeed reads zero. Unfortunately the computerized flying instructor doesn’t
know that, so every time he gets back on the arc he turns to place the RMI only 5-degrees in front of the
wingtip, and that is not enough. So, he keeps being blown outside the arc. When it is your turn you will do
better. Right?
The good news is that even with his limited intelligence the instructor keeps the airplane within half a mile
of the arc, and most of the time within ¼ mile. That is good, but not excellent. See if you can do better.
Press the 3-key, again. Then press the “I Have Control” button.
Now it is your turn to try arcing with a wind blowing you outside the arc.
Repeat this exercise until you can stay within 0.2 Nm of the arc (i.e. until you are better than the instructor.
Page 79
Navigation for Professional Pilots
Having the moving map to help you judge the arc makes it easier. Unfortunately most airplanes don’t have
this feature. So, click the “Hide All” button at the bottom of the page and try repeating the arc with no
map to help you.
Once again we have the exact same arc clearance, but now the wind is 30 knots from the east. Watch the
instructor demonstrate this arc.
This time the groundspeed along the 120 radial is only 130 knots, so the arc need only be lead by 0.6 Nm.
The wind will keep blowing the airplane inside the arc. The instructor will therefore keep flying straight
legs, allowing the RMI needle to drop further behind the wingtip to get back on the arc. Take note of the
groundspeed on the DME (too bad the instructor doesn’t do that.)
A wise pilot would realize that in this situation the RMI needle should be kept behind the wingtip. But, the
instructor is a bit too dense for that. Every time he gets back on the arc he turns to put the RMI needle five
degrees ahead of the wingtip (as you would in zero wind.) Predictably he is blown back inside the arc and
has to correct again.
Press the 4-key, again. Then press the “I Have Control” button.
Now it is your turn to try arcing with a wind blowing you into the arc.
Learn from the instructor’s mistakes. You can do better than he. Try keeping the RMI needle further behind
the wingtip than you did with zero wind. You should be able stay within 0.2 Nm of the arc.
This time there is a new arc clearance. This arc goes clockwise. It is also at a different distance, 10.0 DME.
Watch as the instructor flies the arc. The start radial is 270, so the first turn is to heading 270 + 90 = 360.
There is a 20-knot wind from the southeast so the wind is blowing the airplane outside the arc. As usual
the instructor doesn’t keep the RMI needle far enough ahead of the wingtip, so he keeps blowing outside
the arc.
Press the 5-key, again. Then press the “I Have Control” button.
Page 80
Navigation for Professional Pilots
Now it is your turn to try the clockwise arc. All the procedures you have learned so far still apply.
Remember that with the wind blowing you out of the arc you need to keep the RMI needle slightly in front
of the wingtip.
At this point we have covered all the techniques of arcing. What you need now is lots of practice. Every
time you click the “Do Another” button the computer generates a random arc clearance with a random
wind. The arcs are at distances from 6 miles to 12 miles.
The two checkboxes at the bottom of the simulation labeled “Inside Intercept” and “Outside Intercept”
are both checked by default. Thus you will get both intercepts from inside and outside the arc. If you wish
to limit your practice to only one of these situations adjust the checkboxes.
Make sure you are practicing successfully with all the visual aids hidden before moving on. If you are able
to arc successfully with this simulation you should be ready to try it in the real airplane.
1. Intercepts Inbound
2. Intercepts Outbound
To intercept a course inbound we use a simple little saying, “Desired to the head, plus 30.” You will soon
see what that means. You can only complete an inbound intercept if you are currently within 60 degrees of
the course you wish to intercept. If you are off course more than that go directly to the station and
perform a procedure turn to establish yourself on the assigned course.
To intercept a course outbound we use another simple little saying, “Tail to desired, plus 30.” Outbound
intercepts can be completed regardless of how many degrees you are currently off course.
As usual choose your cruise speed before clicking the “begin” button to start the simulation.
Before we begin you must choose a navigation display. You can make your choice from:
Page 81
Navigation for Professional Pilots
A = All
H = HSI
R = RMI
The procedure for conducting predetermined intercepts (PDT) and flying procedure turns is exactly the
same regardless of what navigation display you have. However it is MUCH easier with an HSI and RMI
than without. Indeed the very reason people spend so much money to have HSI in airplanes is to make
intercepts easier to visualize. Therefore I recommend you start with the option “A” for all, or “H” for HSI.
By default the simulation generates a random inbound intercept. Leave the checkbox at the bottom of the
simulation set to “Within 60 PDTs” for now.
At the right side of the screen the red box contains the clearance.
“Pilot 200, you are cleared to intercept the 180 degree radial inbound to the YPB VOR.”
Alternatively, if you have chosen either the “R” for RMI or “F” for fixed card navigation displays the
clearance reads:
“Pilot 200, you are cleared to intercept the course 360 inbound to the CM beacon.”
Note the difference in terminology. When dealing with VOR or VORTAC navaids the controller (red box)
uses the terminology radial to refer to the course. But when dealing with NDBs the controller uses the term
course.
Page 82
Navigation for Professional Pilots
The clearance requests the pilot to intercept the 180 radial inbound, as depicted in the picture above.
From the picture it is pretty easy to see that we need to fly eastward. But, in a real airplane there won’t be
a map (in most cases) so we must learn to figure out which direction to fly by looking at the HSI, standard
VOR, or RMI indicators.
As you are reading this, the instructor is flying. He figures out that he needs to fly a heading of 070 to
intercept the course. Once on heading 070 everything falls into place. The question is; how does he know
that he should fly heading 070?
We must define:
1. Assigned Course
2. Desired Course
5. Head
6. Tail
7. Track Error
8. “Within 60”
Page 83
Navigation for Professional Pilots
For an inbound intercept the assigned course is always the direction TO the station. Therefore if the
controller has assigned the intercept in terms of radial you must take the reciprocal to get the assigned
course.
For an outbound intercept the assigned course is always the direction FROM the station. There is no need
to take a reciprocal when dealing with outbound courses.
The present bearing is the direction that, at present, would take you to the station. If you have an RMI the
present bearing is the direction the RMI needle is pointing. If you have only a standard VOR indicator you
must center the CDI with a TO flag to get the present bearing.
The present radial is the direction that, at present, you are FROM the station. If you have an RMI it is found
by reading the tail of the RMI needle. If you have only a standard VOR indicator it is the bearing you get
when you center the CDI with a FROM flag.
The difference between the assigned course and the present bearing is called the track error. (It is easy to
visualize on an RMI/HSI combination instrument (see picture below), as the angle between the RMI needle
and the Course bar.)
The PDT procedure we are about to learn only works if you are within 60 degrees. If track error is more
than 60 you must fly directly to the station and do a procedure turn.
Your first task is to set the HSI to the assigned course (if you have an HSI.) For a radial put the tail of the
course bar on the assigned radial to set the inbound course.
Page 84
Navigation for Professional Pilots
Next, make sure you are within 60. Usually in a real world context you will know how far the airway you
are trying to intercept is away from you, so this will be an obvious step. But, in the context of this
simulation you must find your present bearing (head) and compare that to the desired course (arrow on
HSI) confirming the difference is less than or equal to 60.
Once you know you are within 60 you simply following the little rhyme “Desired to head plus 30.”
This simply means that you locate your desired course on the HSI then move your eyes to the head of the
RMI needle, then move your eyes a farther 30 degrees. That is the heading you need to turn to.
Now that you know the procedure watch the computerized flying instructor execute it. Make use of the
time compression, setting it to zero, when you need time to read the instructor’s mind, or observe where
he is pointing.
As the instructor does the PDT he points at the HSI (if available) or the RMI if there is no HSI, or the
heading indicator if there is neither. It is much easier to follow his explanations if there is an HSI, so I
recommend starting with that navigation display. Later you can have him demonstrate the procedure with
other navigation displays.
Notice that the instructor sets the HSI to the assigned course right away.
Next he locates the present bearing on the RMI and compares that to the course bar. Look at where his
finger is pointing (between the course bar and RMI head.)
Then he returns his finger to the desired course (head of course bar. See picture above.)
Page 85
Navigation for Professional Pilots
Then he moves his finger to the head of the RMI needle. (Labeled in picture above.)
Then he moves his finger another 30-degrees. In this example that is a heading of 070. (See picture above.)
Finally he turns to the heading of 070 and flies that heading until he is on the assigned course.
NOTE: When we say plus 30, we mean 30 beyond the desired course.
Press the 1-key, again. Then press the “I Have Control” button.
Now repeat the PDT yourself. Make sure you go through the procedure methodically. After confirming you
are within 60 say to yourself “desired, to head, plus 30.” When that makes sense to you move on.
The airplane is back at the exact same starting point, and the exact same clearance is given.
Because you set time compression to zero the instructor is on hold. Repeat the rhyme to yourself and try it.
The desired bearing is 360, the head is at 040, so once again the required heading is 070.
It is important to realize that the heading you must turn to depends on where you are, but NOT on your
start heading.
Because the airplane is moving the present bearing is more than 040 by the time the instructor gets
around to checking it. Therefore the heading he decides to turn to is more than 070.
The other thing that probably surprised you is that he decided to turn left, rather than right. Why does he
do that?
Page 86
Navigation for Professional Pilots
The picture above shows what the instructor does. The picture below shows what you might have expected
him to do.
You can see that if he had turned right he would have intercepted the course much closer to the station.
That could be a good thing in many cases. But, if the airplane is already close to the station it can create
difficulties. I find that in real world IFR flying you never really need to worry about this sort of thing. Just
turn the most direct way to the chosen heading. But, if you and your instructor are practicing PDTs and
remaining within 10 miles or so of the station you will find it prudent to take care which way you turn. The
rule programmed into the computerized flying instructor is that if the RMI needle is ahead of the wingtip
he simply turns to the chosen heading. But, if the RMI needle is behind the wingtip he will never turn
through the RMI needle. In the example given he is turning to heading 080 but the RMI needle points to
about 050. So, if he turned right he would fly right through heading 050. Since he is programmed not to do
that he turns the other way.
Page 87
Navigation for Professional Pilots
Once again the clearance is to intercept the same course. But, this time we are on the other side of the
course. The procedure however is exactly the same. Watch the instructor do the PDT. Pay attention to his
finger. Set time compression to zero when you need time to analyze what he is doing.
Press the 3-key, again. Then press the “I Have Control” button.
Once again we are assigned to intercept the same course. And we are at the same starting point as the
previous secret code. But the airplane is flying northeast bound, so things are changing.
As in secret code 2 the instructor will turn the long way around.
Press the 4-key, again. Then press the “I Have Control” button.
Here is your chance to see what happens if you turn left rather than right. Do so at your own discretion.
Before moving on to do outbound PDTs you will need lots (and lots and lots) of practice doing inbound
PDTs. Keep the checkbox at the bottom of the simulation set to “Within 60 PDTs” only, and do lots of PDTs.
It’s a lot harder with the map hidden. Click the “Hide All” button at the bottom of the simulation.
I recommend mastering PDTs fully with HSI before using the other navigation displays. However, if you
wish to do some PDTs with the RMI, standard VOR indicator or Fixed Card indicator you may do so now. If
you do, allow the computerized flight instructor to demonstrate the differences in where you must look to
get the required information. Note that the procedure is always the same. The difference is only in where
you get the required information, and in how easy it is to visualize.
TIP: When you first start doing PDTs you should set time compression = 0 BEFORE clicking the “Do
Another” button. That way you have all the time you need to figure out what heading you want to turn to.
However, once you are getting the PDTs correctly you need to be able to do them in real time. You can
even challenge yourself by setting the time compression to more than real time.
Page 88
Navigation for Professional Pilots
Outbound PDTs
Now we will learn to intercept a course outbound from the station. The good news is that this is even
easier than inbound intercepts.
Turn the Visual Aids On. Reset navigation display to “All” or “HSI.”
If you have the visual aids turned off click the button at the bottom of the simulation labeled “Show All.”
I also recommend returning to the “A” for all or “H” for HSI navigation display.
“Pilot 200, you are cleared to intercept the 000 degree radial outbound from the YPB VOR.”
When intercepting the course outbound I will teach you to use an intercept of 30-degrees.
To perform an outbound intercept we have a different rhyme. “Tail to Desired plus 30.”
Page 89
Navigation for Professional Pilots
Notice that this is a different rhyme than for inbound intercepts. In this one we start at the tail of the RMI,
then we move our eyes to the desired outbound course (set on the HSI) then move our eyes a further 30-
degrees to find the required heading. (If you wish to do a 45-degree intercept just move your eyes 45 past
the desired instead.)
Then he looks a further 30 degrees. The required heading in this example is 330.
You may be thinking to yourself that all these steps are not really needed. All you actually have to do is
look at the HSI. If the CDI were deflected left you fly a heading 30 left of the desired course, if the CDI were
deflected right you would fly a heading 30 right of the desired course. This is true. But, I recommend
checking the RMI for two reasons. The first is that without doing this you don’t know if you are off track 11
degrees, or 111 degrees.
The second reason is that only the procedure described here will work with an RMI or Fixed Card indicator.
The picture above shows the instructor demonstrating the same PDT but with an RMI indicator. To see this
press the R-key then click the “Start Over” button. Now, you will see that you MUST do the procedure as
described above.
Page 90
Navigation for Professional Pilots
This time we are assigned the same course to intercept and we are at the same starting point. But, our
start heading is different. Despite this the instructor comes up with the same intercept heading, 330.
With the airplane frozen you now have all the time you need to go through the procedure. Keep saying to
yourself “tail to desired plus 30.”
Click the “I have control” button, then set time compression to more than zero.
Change the checkbox at the bottom of the simulation to “Include Outbound.” If you wish to do only
outbound PDTs turn off the “Within 60 PDTs” checkbox. Make sure the “Over 60 PDTs” checkbox is NOT
selected.
Initially set the time compression to zero before clicking the “Do Anther” button so you will have time to
think the procedure through. Then set time compression to more than zero when you know what heading
you want to turn to.
Do several PDTs until you are getting comfortable with the procedure.
If you desire, practice outbound PDTs with standard VOR indicator, RMI and Fixed Card indicator.
Page 91
Navigation for Professional Pilots
1. Include Outbound
2. Within 60 PDTs
3. Over 60 PDTs
Every time you click the “Do Another” button the computer will generate a random PDT. Some will be over
60, some won’t. Some will be inbound and some outbound. Read the clearance carefully then try to
comply.
If you need a demonstration you can give the instructor control at any time.
Initially feel free to set time compression to zero to give yourself time to think what you should do. But,
you must work your way up to doing the exercise in real time.
Most airplanes don’t have a moving map. Using the map makes it far too easy to do PDTs. So, once you
understand the procedure hide the visual aids and practice with only the navigation instruments.
Be sure to practice PDTs with all the navigation displays. If you decide not to use a particular display, such
as the Fixed Card indicator you must be certain you won’t encounter one in your real world IFR flying. If
you know for certain that the airplane you are doing your IFR rating in has an RMI you may consider
skipping Fixed Card indicator – perhaps returning to learn how to use it later.
You also know how to fly a circular arc around a VORTAC using a DME and RMI. You know what a lead
radial is and how to set up the HSI and OBS when flying an arc.
Page 92
Navigation for Professional Pilots
You know how to intercept any course, inbound or outbound, from a VOR or an NDB. When an inbound
course is within 60 degrees you can go right to it. When the course is more than 60-degrees from your
present bearing you know how to fly to the station and perform a procedure turn.
With the above skills you have all the knowledge you need to master holds and approaches. In the next
chapter we will learn to perform holds. Keep your bracketing skills at the ready. In chapter 6 we will learn
to do approaches where you will be able to use al l the skills you have just learned, including arcs and
procedure turns.
Page 93
Navigation for Professional Pilots
Page 94
Chapter 4
IFR Charts
Read section Map 3.2 in your AIM.
LO
HI
Terminal
LO Charts
LO charts are used for enroute navigation within the low level airspace. They show the “low altitude”
airways and air routes, which are for airplanes flying less than 18,000’. High level airways are shown on
the HI charts discussed below.
Airways are based on either VOR or ADF. Even if you are navigating with GPS or Loran-C the airways you
fly on are based on the positions of VORs and NDBs. The LO charts give the magnetic tracks for these
airways. The charts also show distances so no ruler or protractor is necessary when flight planning with LO
charts. To fly IFR on an airway you need an IFR clearance, which is explained below.
LO charts also show air routes, which are similar to airways but uncontrolled. You will learn the regulations
governing these in Avia 130.
If you have worked through the designated simulations you know how to tune and interpret VOR and ADF
radios with either HSI or standard VOR indicators and fixed card or RMI. If not then review that material
before proceeding.
In Canada all airways are based on either VOR or ADF. The VOR airways are called “Victor airways.” All
Victor airways have a number which is preceded by the letter V, for example V100, or V302. In an IFR
clearance these would be referred to as Victor one zero zero and Victor three zero two. ADF airways are
commonly called “Low frequency airways,” they are always designated with the letter A,B,G, or R. The
standard phonetic terminology is used, for example airway B22 is referred to as “Bravo two two.”
Review the legend on your LO1 chart and then do the assignment to confirm you know all the symbols on
the charts.
Navigation for Professional Pilots
HI Charts
HI Charts are used for enroute navigation in the high altitude airspace, i.e. at and above 18,000 feet in the
southern domestic airspace (all flight in high level airspace is IFR.) Most high altitude airways are based
on VORs but some are based on NDBs, all are named with a letter “J” followed by a number, for example
J585. In a clearance this is referred to as “Jet five eight five.”
Examine the legend of your HI altitude chart and then do the assignment to confirm you understand it.
Note that HI charts do not symbolically indicate which direction corresponds to even and odd cruise
altitudes because these altitudes change according to the cruising altitude orders. You will learn about this
in Avia 130 and Avia 260.
Airplanes flying along airways in opposite direction cannot pass the way cars on a highway do. Cars pass
each other at combined speeds of 200+ KPH missing head-on collisions by four or five feet (pretty terrifying
when you stop to think about it. Imagine trying to do it blindfolded.) Airplanes are separated by having
opposite direction airplanes at least 1000 feet apart vertically. Eastbound airplanes fly at “odd thousand”
altitude (1000, 3000, 5000, etc.) while westbound flights are at “even thousand” altitudes. VFR airplanes
are “separated” from IFR by 500 feet (you already know the cruise altitudes for VFR.) This system works
well for airplanes in cruise but is problematic when many airplanes need to climb or descend. Obviously an
airplane climbing to 9000 feet (eastbound flight) must climb through 2000, 4000, 6000, and 8000 creating
a risk of colliding head-on with westbound traffic in each case. Air traffic controllers are charged with
making sure no collision takes place (and your life depends on them doing it, every time.)
Cruising altitude rules for separating opposite direction flights is not satisfactory in the vicinity of busy
airports because large numbers departing and arriving airplanes are climbing and descending creating a
night-mare scenario for the controller. Preferred IFR routes, STARs, and SIDs are the answer. These are not
unlike one-way streets you find in big cities.
Page 96
Navigation for Professional Pilots
When planning an IFR flight one task you must obviously do is choose a route. It might seem obvious that
you would simply look at the LO or HI chart (LO for airplanes that cruise below 18,000 and HI for airplanes
that cruise at and above) and choose the airway(s) that most directly take you from your departure airport
to the destination. Before doing that however you should look to see if there is a published “preferred
route.” This is the aeronautical equivalent of one-way streets that you have probably driven on in large
cities. ATC finds it easier to control the flow of climbing and descending traffic (departures and arrivals)
when outbound airplanes take one route (or set of routes) and inbound airplanes another. Departing
airplanes can be cleared to climb without fear of opposite direction traffic, and similarly arrivals can be
permitted to descend. The controller only needs to ensure that faster and slower airplanes don’t “over-
run” each other, which is still a substantial task for ATC, but at least one problem is eliminated.
Preferred IFR routes are published starting on page C98 of your CFS. If a preferred route exists you should
use it. While the CFS indicates that the system is not mandatory you will find it impossible to get a
clearance that does not comply unless you indicate a safety concern (bad weather) or a special operational
need (lack of pressurization, special ferry flight, etc.) The bottom line is to use preferred routes.
When departing from a small airport there is often no listed preferred route but if you are headed for a
major airport you should use common sense and pickup a preferred route; for example departing
Castlegar for Vancouver intercept the preferred route for Calgary to Vancouver.
IFR flight makes it possible for airplanes to fly in cloud from departure to destination, thus largely
removing weather as an impediment to flight. A few problems arise when flying in cloud however:
1. Airplanes cannot see each other in flight, so some method of separating them must exist
2. Airplanes cannot see the ground, so some method of avoiding it must exist
3. Airplanes cannot see the runway, so some method of descending and establishing visual contact
with the runway is needed in order to land
The ATC system exists PRIMARILY to keep airplanes from colliding during flight. Some aspects of this task
have been indicated above. Any other services that controllers provide are secondary to the primary
function. In short the ATC system solves only problem 1 above.
Pilots follow prescribed procedures and climb at specified climb gradients to avoid terrain during
departure and when enroute they fly above minimum enroute altitudes (MEA.) MEAs are shown on LO
charts. The key word in the previous sentence is procedure and we say that terrain avoidance in IFR flight
Page 97
Navigation for Professional Pilots
is “procedural.” Note that it is NOT the responsibility of ATC to prevent terrain collision. Pilots are
responsible for that through the correct application of IFR procedures.
IFR approach procedures are published in the Canada Air Pilot (CAP) which you have purchased. These are
for the purpose of making a safe descent (taking terrain into account) to a point where the pilot MUST see
the runway in order to land on it. So problem 2 and 3 above are both solved procedurally.
It is always possible that the weather will be so bad that the pilot does not see the runway at the end of an
IFR approach procedure. In this case an alternate airport, where the weather is good, is needed. You will
learn all the regulations for this elsewhere, but it should be obvious that the alternate airport must have
good weather so that there is NO CHANCE of being unable to land there.
You will learn to assess the FORECAST to determine that an airport is a “legal alternate.” The required
weather is specified in the CAP GEN and in RAC 3.14. On all IFR nav-logs you will include time and fuel to
get to an alternate airport.
Page 98
Navigation for Professional Pilots
Page 99
Chapter 5
The CR Computer
You have already learned to use the wind side of the CR, now it is time to master the front-side. Work
through your CR manual from page 1 to 29 (you should already have done the rest of the book.)
A Ratio Machine
The outer two rings on the front-side of the CR are a “ratio-machine.” You will learn to do many useful
ratios all of which have practical application in your flying. First a quick review of what a ratio is:
½ = 2/4 = 3/6 = 18/36, etc. These are simple examples of ratios and fractions, for our purposes, ratios
should be thought of as fractions. One half equals two quarters, three sixths, and eighteen thirty-sixths,
and an infinite number of other ratios. The CRUCIAL thing to realize is that you can set any ONE of these
ratios on your CR and it will give you ALL the others. In the photo below you can see that all the ratios are
given. Get out your CR and set one of the above ratios and see that you have them all.
Before we go further it is important to note how numbers are displayed on the CR. On a CR 10 can
represent 1, 10,100, 1000, etc. Thus 10/20 in the photo above represents ½ as well as 10/20, 100/200 and
so on. 18/36 also represents 180/360 and 1.8/3.6 and so on. It is your job to keep track of the decimal
Navigation for Professional Pilots
points when using your CR. It is important to know that not only does ½ = 2/4 also equals 20/40 and
2000/4000, etc.
From the photo above, or your own CR, you can see that ½ equals 17/34 and 17.5/35 and an infinite
number of other ratios not previously listed. But in a given situation only a few of these ratios are of
practical interest – even so it is important to understand that there are an infinite number of equivalent
ratios
The secret to making good use of a CR is in knowing which ratios are interesting. This depends on what
question you are trying to answer. A common problem is time and distance, which we will deal with under
the topic of speed ratios below. But there are many other ratios of importance in aviation. For example
climb gradients, distance to a radio navaid, unit conversions, etc. Solving problems with a CR requires you
to ask, what relationships are relevant? For example IFR departures require a minimum climb gradient of
200 feet per nautical mile (ft/NM.) To use a CR effectively you must realize that this is a ratio (200/1.) A
good clue is the word “per”; when you know that something happens “per” something else it is probably a
ratio that you can solve with a CR. For example if you are paid $14 per hour and want to know how much
you earn in 40 hours the CR can tell you. The photo below shows that you earn $560 dollars in (per) 40
hours. How many dollars do you earn in 8 hours?
Page 102
Navigation for Professional Pilots
Unit Conversions
Most unit conversions are simple ratios. Examples include pounds/kilograms, liters/gallons, statute-
miles/kilometers and nautical-miles/kilometers. If you establish ANY relevant ratio relating these values
you can use it to determine ALL others, using your CR. For example you may have noticed on the
speedometer of your car that 80kph equals 50 mph – set this ratio up on your CR and fill in the table
below:
Page 103
Navigation for Professional Pilots
To solve the above problem we started with the ratio 80/50 which we remembered from the speedometer
of a car – but the CR has most of the common ratios marked on its face. Remember that any ratio will do,
so Jeppesen simply marks the ratios wherever they fit without cluttering the face of the computer too
much.
The photo above shows a ratio for km/sm. Once this ratio is set all others can be read. The KM and Statute
markings are found on both the outer and inner ring so you can set the CR up either way.
Page 104
Navigation for Professional Pilots
Feet to meters
Pounds to Kilograms
Remember that if you know a conversion ratio from memory you can save the need to locate one on the
CR. For example if you know that 2.2 pounds equals one kilogram simply set that ratio on the CR to save
the trouble of locating the marked ratio shown below:
Set the above ratio and confirm that 2.2/1 is an equivalent ratio.
The CR does not have a conversion from Nautical miles to feet. You will often need to know that 1.0NM =
6080 feet. If you forget you can figure it out with a CR through a two-step process. First determine how
many KM = 1NM and then convert from meters to feet. Try it yourself to confirm you get the expected
value. The same process can be used to discover there are _______ feet in a statute mile.
Page 105
Navigation for Professional Pilots
-40°C = -40°F but 1°C does not equal 1°F. The reason ratios don’t work is that 0°C does not equal 0°F. For
all the other conversions we looked at so far the zero points match. That is a requirement for using ratios
as a conversion method.
The CR has a temperature conversion scale on the front face (see photo below.)
You can see that -40°C = -40°F but that 0°C = 32°F. 20°C = ____?
Mach Number
You will use Mach number extensively in flight planning. It is a ratio.
Assume the speed of sound is 600 knots and set the ratio 600/1 on your CR, as shown below.
With your CR set as above 1200 knots is what Mach number? The answer is 2.0
Page 106
Navigation for Professional Pilots
A C-172 cruising at 105 knots has what Mach number? What is the Mach number of a King Air cruising at
240 knots?
The above conversions from TAS to Mach number are simple but only accurate if the ratio 600/1 is correct.
In fact this ratio is only approximately correct; the real speed of sound varies with air temperature. You will
notice that once you set 600/1 on the CR a Mach index is visible that allows you to “fine tune” the ratio for
the actual air temperature. You can see the index in the photo below.
Set the Mach index to -25°C (the ISA temperature at 20,000’.) What is the speed of sound? This amounts to
1
saying what TAS corresponds to Mach 1.0 . An airplane cruising at Mach 2.0 has a TAS of _____ knots. An
airliner cruising at Mach 0.8 has a TAS of _____ knots. What would the TAS of the airliner be if the air
2
temperature was -56°C?
1
610 KTAS
2
490 KTAS
Page 107
Navigation for Professional Pilots
To be cheeky you could say, “My speed is 17 miles per 11 minutes.” That is a pretty weird unit, but it is
indeed your groundspeed. It is however traditional to specify speed in units of Knots. Knot is defined as NM
per hour, but in reality it is NM per 60 minutes. It is VITAL to realize that the symbol, even though
it has 1:00 written on it, actually represents six (6) or 60 on the CR, as you can see in the photo below:
Thus we would say that our groundspeed is 93 knots, which means 93/60. How far do we go in 30 minutes,
how far in 12 minutes? You can determine these and an infinite number of other ratios once17/11 has
been set – it’s just that you don’t usually think to ask such questions.
There are however other ratios that are important beyond the simple 93/60 ratio that is “our
groundspeed.” For example how many miles do we go in one minute. The photo that shows the 17/11
ratio also shows the ratio 1.54/1. This is an important value to know, sometimes. The airplane is covering
1.54 NM every minute.
If the total length of the trip is 170 NM, how long will it take to get there? Note that since we are
responsible for the decimal points the same ratio 17/11 gives the answer. Common sense says that it will
Page 108
Navigation for Professional Pilots
3
take 110 minutes to fly 170 NM. How long would it take to fly 88NM? How long would it take to fly
214NM? Make up your own distances and confirm that you can find the time for any distance you choose.
To approach this problem from the other direction, if you are flying 1 nautical mile per minute what is your
groundspeed? In this case set 1/1 and look up x/60. Note that the answer is 60 KTAS. At 60 knots how long
does it take to fly 18NM? How long for 78NM? How long for 156NM? The answer to all these is trivial and
you should not require your computer.
60 knots – i.e. 1.0 NM/min is an IMPRORTANT speed that we will use extensively so you must remember
it.
If you are flying 2 miles per minute your groundspeed is _____ Knots.
If you are flying 3 miles per minute your groundspeed is _____ Knots.
3
57 minutes
4
1.5 NM/min
Page 109
Navigation for Professional Pilots
The airplane in the diagram is flying around a circle. At the moment shown it has flown 17° of arc in 11
minutes. What is the arc-speed?
Arc-speed has units of degrees per hour, which of course really means degrees per 60 minutes. Simply set
your CR for the ratio 17/11 and lookup the answer. The result is exactly the same as the groundspeed
example above in which the airplane flew 17NM in 11 minutes, but this time the arc-speed is 93
degrees/hour. How long will it take to fly 20 degrees? How long will it take to fly 60 degrees?
Hopefully your reaction to the above is that it is trivially obvious (but you may be thinking it is unimportant
– trust me it is VERY IMPORTANT.) Be sure to examine the above until you fully understand it. Here are a
few sample problems for you to work through just to be sure:
You fly 14 degrees in 7 minutes; your arc-speed is ______ degrees/hour. It will take _____ minutes to fly 60
degrees; it will take ______ minutes to fly 57.3 degrees.
Page 110
Navigation for Professional Pilots
You fly 37 degrees of arc in 3 minutes. Your arc-speed is _____ degrees/hour. It will take ______ minutes
to fly 60 degrees; it will take ______ minutes to fly 57.3 degrees.
It is now time to review some high school trigonometry. First recall what an equilateral triangle is:
An equilateral triangle is one that has all three sides the same length and all three angles equal. The three
angles must all be 60 degrees (the sum of the three angles in every triangle is 180°)
The three sides of an equilateral triangle are equal to each other. In the diagram above distances AB = AC
= BC.
Page 111
Navigation for Professional Pilots
The diagram above is the same as the previous one with an arc added. The center point of the arc is B.
Look at the diagram and estimate the length of the arc compared to AC. Obviously the arc is longer, but
how much - 1%, 10%, what do you think?
It should be obvious that there is some angle, just a bit less than 60°, such that the length of the arc is the
same as the length of the sides AB and BC. Obviously AC will have to be shortened, consequently the
triangle will not be exactly equilateral any more, but it will be close. Consider the diagram below.
Page 112
Navigation for Professional Pilots
In the diagram above the angle through which the arc sweeps is reduced to 57.3 degrees. This is the
“special” angle for which the length of the arc is exactly equal to the radius. I.E. AB = AC’ = arc. AB and AC’
have been labeled r in the diagram to remind us that they are the radius of the arc. 57.3° is known as one
radian.
The sample problems above asked you to determine the time to fly 60 and 57.3 degrees of arc, we will now
examine why.
Returning to a previous example in which the airplane few 17° of arc in 11 minutes (setup your CR for the
ratio 17/11.) The time to fly 57.3° of arc is 37 minutes. But, since the length of the arc equals the radius it
obviously also takes 37 minutes to fly directly to the center of the arc (point B.) The time to fly 60° is 39
minutes. Most pilots use this as the answer because it is a lot easier to remember 60 rather than 57.3 (57.3
= 180/Π.)
Time to the station is a common problem in aviation. You will even more commonly need to know distance
to the station, but that is a two-step process which we will cover in just a moment. First let us consider the
most common situation in which the above theoretical facts comes into actual practice.
In the above diagram the airplane is flying an eastbound track that passes north of a VOR. The pilot wishes
to know how long it would take to get to the VOR if s/he turned southbound directly to it. To find out,
without the need to actually do it, record the time from A to B and the angle X. To be effective AB must
approximate flying an arc, so the station must be essentially abeam the airplane (as in the diagram.) The
angle X is usually fairly small, typically less than 15° (but not too small or there will be “round off error.”)
Angle X is arbitrary, so it doesn’t matter if it is 4°, 7°, 11°, 15°, etc. simply time whatever is convenient.
Once you have a “time / x-degrees” ratio setup on your CR all you do is lookup time for 57.3°or 60°.
Neither will be precisely accurate, but either will give an answer that is within 5% of the correct value.
The above use of “arc-speed” to determine time to a station when flying abeam is one of the most
common uses of arc-speed theory. As you can see, it is an approximation since the airplane actually flies a
Page 113
Navigation for Professional Pilots
straight line forming a triangle with the station, but the previous analysis that showed an equilateral
triangle is very similar to a one-radian arc. It is recommended that in these calculations you use 60° as the
reference angle rather than 57.3 (i.e. think of the equilateral triangle analogy to help you remember how
to do it.)
Next we will consider a more precise use of arc-speed theory. Consider the modified approach plate
5
below :
To fly this arc you start at the point marked and maintain a constant 9 DME arc to intercept the 087 radial
(which lines you up for landing on runway 09.)
On the right side of the plate a Lead Radial (LR) is published, but its value has been erased on the above
photo. The LR is always 2NM prior to intercept of the final approach course (087 radial in this case.) What
should the LR be? See if you can figure it out based on arc-theory before reading the next paragraph.
To answer the question we need to realize that 57.3° of arc will be 9NM, since it is a 9 DME arc. So set the
ratio 9/57.3 on your CR and look up 2/a. The answer is 12.7°. Note that if you had used 9/60 as your ratio
you would get 13.3°. Either way you will round off to 13° and predict the 074 radial as your answer.
5
The original is in the CAP3 under Brandon
Page 114
Navigation for Professional Pilots
Imagine you are flying the above arc arrival and wish to slow down and start your pre-landing checklist
5NM prior to intercepting the final approach track, what radial should you start to slow down at? If you
kept your CR set to 9/57.3 the answer is right in front of you. Look it up before reading the next paragraph.
With your CR set to the ratio 9/57.3 lookup 5/a. The answer is 32°. So you will need to slow down at the
055 radial.
The above uses of arc-speed are very typical of ones you will experience everyday as a commercial pilot.
Learn them well and get comfortable with them.
Imagine the above DME arc had been 14NM instead of 9. What would the lead radial have been?
Distance to Station
Below the same diagram previously examined has been repeated.
It is much more likely that the pilot wishes to know the distance to the VOR rather than time to the VOR.
Imagine the situation in which the flight plan route passes a certain number of miles north of the VOR. The
pilot wishes to determine if s/he is on track (the airplane could be in IFR weather conditions, over water, or
featureless terrain, so that this method is the only method of fixing position. If the airplane is equipped
with DME the position check would be easy, the pilot would simply note the distance as s/he passed
abeam the VOR, but this particular airplane does not have a DME so we will have to do it the “hard way.”
Page 115
Navigation for Professional Pilots
First, it is important to note that we cannot solve this problem unless we already know the groundspeed of
the airplane. We will assume that the pilot has been doing his/her job well and knows the groundspeed.
Assume the following data and follow along with your CR. The airplane crossed the 355 radial at time 0:00
and crossed the 005 radial 7:00 minutes later. The groundspeed is known to be 144 knots. How far north of
the VOR are we?
This is going to be a two-step process. What is the first relevant ratio? Think it through on your own before
reading the next paragraph. (Tip: what is the angle X?)
The airplane has flown through an angle of 10° in 7 minutes. Setup the ratio 10/7 on the CR. Now
determine how long it would take to fly 60°. The answer is 42 minutes (10/7 = 60/42.) So time to the
station is 42 minutes.
In the second step we will determine distance to the station. We know it would take 42 minutes to get
there, but how far is it? We know that groundspeed is 144 knots. What ratio do we need to setup? Reason
it out before reading the next paragraph.
We setup the ratio 144/60 which represents distance in 60 minutes. The relevant ratios are 144/60 = a/42,
where a represents the answer. The answer is 101 nautical miles.
In summary: When flying abeam a station, calculate distance to the station by:
1. Determining how long it would take to fly a 60° arc (or one side of an equilateral triangle.)
Pilots routinely plan arrivals at a descent gradient of 320 ft/NM (which corresponds to 3°.) Often other
descent gradients are required, especially for non-precision approaches in mountainous environments. We
will thoroughly examine gradients in what follows. Keep in mind that climb gradient and descent gradient
theory is fully interchangeable. Anything you learn about planning descent rates can be applied to climb
rates, and vice versa.
6
This relates to the “procedural” terrain separation previously mentioned in the Overview of IFR Flight
Page 116
Navigation for Professional Pilots
Unfortunately climb and descent gradients are not directly usable by pilots. Our aircraft are equipped with
rate instruments, not gradient instruments. We have an airspeed indicator and often a DME or GPS all of
which give our speed (a rate) and we have a vertical speed indicator (VSI) that gives our rate of climb and
descent. Our challenge is to translate the published climb and descent gradients into useable vertical-
speed/airspeed ratios (rates.)
We will start with a very simple problem, but one that applies to all IFR departures. As stated previously
the minimum acceptable climb gradient is 200 ft/NM, as shown in the diagram below.
We can quite simply answer questions such as; what is the minimum safe altitude 5NM after takeoff? Can
you setup the required ratio? Try to do so before reading the next paragraph.
The ratios are 200/1 = a/5, where a is the answer. The answer is 1000 feet, i.e. you must be at least 1000’
agl 5NM after takeoff to meet the gradient.
When you reach 2000’ agl the maximum distance you should be from the airport is ______ NM.
The problem we most need to solve is; what vertical speed must we maintain to safely meet the gradient?
This is almost trivially simple to answer if you remember that 60 knots is 1.0 NM/min (previously I said that
you needed to remember that fact.) If you forget then set your CR to the ratio 1/1 to remind yourself that
1.0 NM/min means 60 miles per 60 minutes.
Examine the above diagram and imagine the airplane climbing along the flight path at a groundspeed of
60 knots. After one minute it would be at the 1.0 NM point and its altitude would be 200 feet. After two
minutes it would be at the 2.0NM point and its altitude would be 400 feet, etc. It must be clear to you that
it requires a vertical speed of 200 fpm.
To make rate conversions it is CRUCIAL to realize that an airplane with a groundspeed of 60 knots
requires a climb rate equal to the gradient. In this case the relevant ratio is therefore 60/200. What climb
rate do you need at 75 knots? Figure it out on your own before reading the next paragraph.
Page 117
Navigation for Professional Pilots
Set the CR to the ratio 60/200 and lookup 75/a. The answer is 250 fpm. At 85 knots the minimum safe
7
vertical speed is _____ fpm. At 95 knots it is _____ fpm. At 105 knots it is _____ fpm . At 120 knots it is
_____ fpm.
Not all departures can be made safely at a gradient of 200 ft/NM. When a larger gradient is required the
departure chart will specify the required value. The plate below is an example:
You can find the above plate in your CAP2 under Victoria International, Mill Bay SID. Depending on which
transition ATC assigns, a climb gradient of 330 ft/NM or 220 ft/NM applies. Let’s work out the required
vertical speed for each case – starting with 330 ft/NM. What ratio should you setup on your CR? Try to
figure it out before reading the next paragraph.
We must realize that at 60 knots the required vertical speed is 330 fpm. So set the ratio 60/330 and lookup
your-speed/a. [Tip: it makes no difference whether you setup 330/60 or 60/330 as long as you keep track
of whether groundspeed or vertical speed is on the top of the ratio.]
If your groundspeed is 75 knots the required vertical speed is 415 fpm. At 85 knots it is ______ fpm. At 105
8
knots it is ______ fpm .
Make sure that the above calculations are effortless for you. You must routinely check the minimum climb
rate for IFR departures.
Before we move on to the next important point it should be pointed out that you can approach the above
problems from the opposite direction. If you know your groundspeed and vertical speed you can use the CR
7
350 fpm
8
580 fpm
Page 118
Navigation for Professional Pilots
to determine your actual climb gradient. This is also helpful for flight planning purposes. We will use it
quite often, so it is worth covering now. Imagine that you know your groundspeed is 115 knots and that
your vertical speed is 800 fpm. What is your climb gradient? What ratio should you setup, and how do you
get the answer? Figure it out before reading the next paragraph.
The relevant ratio is 115/800 = 60/a. The secret is to realize that the ratio groundspeed/vertical speed, i.e.
115/800 establishes the gradient. To get the value in units of ft/NM remember that 60 knots is 1.0
NM/min, and look up the vertical speed at 60 knots. In this case the answer is 416 ft/NM. As long as this
value exceeds the published climb gradient the pilot need not worry. This calculation can also easily be
extended to answer questions of the form; what altitude will this airplane be at when 6.4 miles after
takeoff? [Tip: this is step two of a two-step problem.] Try to figure out the answer before reading the next
paragraph.
We know the climb gradient is 416 ft/NM so setup the ratio 416/1 and lookup a/6.4. The answer is 2660
feet.
A particular airplane climbs at 160 knots and 1000 fpm. What is the climb gradient, and what altitude will
it be at 3.7NM after takeoff?
The first ratio is 160/1000 = 60/a. This gives a climb gradient of 222 ft/NM.
The second step is to use the climb gradient, so set the ratio 222/1 = a/3.7. The airplane will be at 830agl
3.7NM after takeoff.
You can see that the above two-step calculation is quite useful for flight planning. Go over it until it makes
complete sense to you.
Next we examine a very important, but not significantly different, situation related to approach planning.
Consider the following approach plate, which is quite typical.
Page 119
Navigation for Professional Pilots
The approach plate above can be found in your CAP2 under Abbotsford NDB RWY 07. On this approach the
airplane must cross the XX NDB at 1700 (or above) and then land on runway 07, which has a touch down
zone elevation (TDZE) of 174. The XX beacon is 4.3NM from the runway. All this information is presented
on the above plate; be sure you can locate it for yourself.
The airplane must descend 1526 feet (1700 – 174.) The pilot will of course not land exactly at the runway
threshold; normal touchdown is made about 0.2NM past the threshold, so the descent must be completed
in 4.5NM. What is the descent gradient? Try to figure it out yourself before reading the next paragraph.
The relevant ratio is 1526/4.5 = a/1. The answer is 340 ft/NM. What vertical speed is needed? Try to setup
the required ratio on your own before reading the next paragraph.
The relevant ratio is 60/340 because at 60 knots 340 fpm would be required. The required vertical speed
depends on your groundspeed such that 60/340 = groundspeed/a. If you fly the approach at 105 knots the
vertical speed must be 600 fpm. At 90 knots the vertical speed must be ______ fpm. At 140 knots the
vertical speed must be ______ fpm.
The above calculation will be needed for every non-precision IFR approach you fly, so it is important to
become comfortable with it. You should open your CAP at random and calculate the descent gradient for
the final approach segment of many non-precision IFR approaches (i.e. not ILS approaches), and resulting
vertical speed at your airplane’s approach groundspeed, until you can do the calculation quickly and
effortlessly.
Examining the Abbotsford approach plate once again, we see that in the intermediate approach segment
the airplane must descend from 2500 to 1700. How far back from the XX NDB should this descent begin if
the pilot wishes to maintain a descent gradient of 340 ft/NM (the previously calculated gradient for the
final segment)? Setup your CR as required before reading the next paragraph.
Page 120
Navigation for Professional Pilots
The airplane must descend 700 feet (2500 – 1700.) The relevant ratio is 340/1 = 700/a. The answer is
about 2.1NM.
If the pilot wishes to limit the intermediate segment to a gradient of 320 ft/NM the descent should start
______ NM from the XX beacon.
Most precision approaches are set to a descent angle of 3°, which is a gradient of 320 ft/NM. Some
precision approaches use other gradients. Legally a precision approach can have glidepaths in the range
2.5° to 4.0°.
The above diagram shows a 3° descent, which corresponds to 320 ft/NM. This can be calculated using
basic trigonometry. Tan (3) = a/6080 (recall that 1.0NM is 6080 feet.) Using an electronic calculator a
equals 318.7, which we will round off to 320.
How many nautical miles are required for a descent of 1000 feet on an ILS? Setup the required ratio on
your CR before reading the next paragraph.
The above relationship is VERY IMPORTANT. However, most pilots round it off to 1000 feet per 3.0NM,
which is close enough for typical purposes and allows quick and easy calculations in your mind without
needing a CR. Below are some typical applications. Work them out based on the ratio 1000/3; if you like
you can rework them based on the more accurate 320/1 to see if the difference is significant.
The tower asks you to report 2NM on final; what altitude will you be at? Setup your CR before reading the
next paragraph.
Page 121
Navigation for Professional Pilots
The ratio is 1000/3 = a/2. You should report 2.0 final when you are 666 above ground level (note that you
can thus report 2.0 final even if your airplane is not equipped with DME.) If you had used the more precise
ratio 320/1 your answer would be 640agl. From a practical point of view reading the difference on your
altimeter and then reporting would be impossible.
You are going to intercept the glidepath at 3000agl, how far from touchdown will you be? Setup your CR
before going on.
If you set 1000/3 = 3000/a; the calculation is so simple you hardly need a CR. You will be 9.0NM from
touchdown. If you set the more precise ratio 320/1 the answer is 9.4NM. This is the actual distance, but
since your primary purpose in such calculations is usually just to keep a mental image of how far you are
from touchdown the difference between 9.0 and 9.4 is probably not significant.
You are flying an ILS approach with a groundspeed of 120 knots, what vertical speed do you require? Setup
your CR before reading the next paragraph.
The required ratio is 60/320 = 120/a. The answer is 640 fpm. This is an important calculation, but given
that positive guidance is provided by the glidepath it is really only necessary to approximate this
calculation. With your CR set to 60/320 what is the value of 1/a. Note that a equals 5.3. This ratio tells us
that we need 5.3 fpm for every knot of groundspeed. Pilots routinely round this off to 5.0. From this comes
the rule of thumb that vertical speed should be 5 x groundspeed. Using the 120 knot example we get 5 x
120 = 600 fpm. We know the correct answer is 640, but 600 fpm will get you started close enough, you
then follow the glidepath indicator, which will take you directly to the runway.
Summarizing what we have learned about flying 3° precision approaches. In order to facilitate mental
calculations while flying ILS approaches pilots use the ratio 1000/3 or 100/.3 to approximate the descent
gradient. Pilots also use the formula 5 x groundspeed to approximate the descent rate.
Use the approximations to answer the following questions without using your CR or any other calculator.
Your company SOP is to call 100 above as you approach the glidepath check altitude. You will be ____ NM
from the checkpoint when you make this call.
You will intercept a glidepath 600 feet above the glidepath check altitude. That will be _____ NM from the
FAF.
Your groundspeed is 100 knots; the required descent rate is ______ fpm.
You are 400 agl when the tower asks, “How far back” you are. Your answer is _____ NM.
Page 122
Navigation for Professional Pilots
It is important to know that the actual air temperature is NOT -21°C; the friction of the air rushing past the
temperature probe causes an error and the actual temperature is colder than -21°C. We will see how much
colder shortly.
FL250 means that your altimeter is set to 29.92, so your pressure altitude is 25,000’.
From the King-Air POH we look at the calibration chart to see what our CAS is. At 170KIAS there is no error,
so our speed is 170 KCAS.
On the CR (CAS window) set 170 KCAS opposite 25,000’ pressure altitude, as shown below.
Keeping the CR in that position, rotate it so you can look at the TAS window. Set the indicated temperature
hairline to -21°C and read the TAS on the scale, see photo below.
Page 123
Navigation for Professional Pilots
Temperature rise (see photo below) is 8.2°C, in other words the actual temperature is -29.2°C.
There are lots of sample problems like the one above in the assignments. Remember that when doing this
sort problem with your CR you would be in flight and checking that your TAS is working out as flight
planned.
Page 124
Navigation for Professional Pilots
It is much simpler to do this for airplanes that fly less than 200 knots and less than 20,000 feet because we
can disregard compression error. The CR has two techniques:
1. A quick and simple technique that does NOT compensate for compression; for aircraft slower than
200 knots
2. A two-step procedure that accurately allows for compression. This can be used for all airplanes,
both fast and slow; but MUST be used for fast airplanes.
You are expected to learn both procedures and apply the two-step procedure when needed (i.e. for any
airplane flying faster than 200 knots, or higher than 20,000 feet.) Of course you can always use it, but it
takes longer and is not needed for slow airplanes like the C-172 or B95; for the King Air you must use
procedure 2. Obviously jet pilots always use procedure 2.
65% power
Page 125
Navigation for Professional Pilots
Line up the temperature of -12°C with the PRESSURE ALTITUDE of 8070’, as shown in the photo above.
Take care to keep the above values aligned while you locate the TAS on the outer ring. CAS appears
directly below it; in this case 111KTAS equals ~101 KCAS.
To get the indicated airspeed look in the calibration chart on page 5-8 of the POH. In this case indicated
airspeed is about 2 knots more than calibrated so the final answer is 103 KIAS.
Page 126
Navigation for Professional Pilots
You will be using the above procedure over and over, on all your flight plans for the C-172P and Beech 95,
so make sure you can do it without hesitation.
The procedure works because temperature affects calibrated airspeed and the speed of sound equally and
therefore the effects offset. For a given Mach number there is one CAS for each pressure altitude,
regardless of TAS.
An IMPORTANT point to note before we go further is that since the TAS window on the CR works with
INDICATED temperature (see photo below) and indicated is NOT the same as actual air temperature, you
cannot use the TAS window to predict CAS by reversing the procedure covered above.
The proper procedure is to first determine your Mach number. To do that you need to know TAS and the
speed of sound. Your POH gives you TAS and the CR gives you the speed of sound.
Page 127
Navigation for Professional Pilots
Mach number is simply the ratio TAS/speed-of-sound. Using the method described earlier reveal the Mach
Index by setting 600 knots over 1 on the outer scales (this is shown below.)
Next set the actual air temperature on the Mach index to get the “real” speed of sound. The photo below
shows the Mach index set to -30°C. On the outer scale you should now see that Mach 1.0 corresponds to
606 knots. If you were at Mach 2.0 your TAS would be 1212 KTAS, what is your TAS if you are at Mach 0.8,
9
what is it a Mach 1.4?
9
850 KTAS
Page 128
Navigation for Professional Pilots
Returning to our problem, we know that our TAS is 277. What is the Mach number? You can read it on the
scale as shown below.
Locate the TAS on the outer scale and read the Mach number. In this example true airspeed of 276
corresponds to Mach 0.455. Notice that when air temperature changes Mach number changes, but
altitude per se is irrelevant.
You are now ready for the second step. Go to the TAS window and set the Mach number as shown below.
Page 129
Navigation for Professional Pilots
With the Mach number set look in the calibrated airspeed window across from 23,000’ pressure altitude to
get the CAS. The photo below shows the result.
In this example CAS is 195 KCAS, which is roughly 197 KIAS according to the POH.
This procedure works because ANY airplane at FL230 and Mach 0.455 has a calibrated airspeed of 195
KCAS, regardless of temperature.
You will be using the above procedure many times in flight planning so make sure you go over it until you
can do it without hesitation.
Page 130
Navigation for Professional Pilots
Setting the Mach index to -12°C the speed of sound becomes 628 knots. More importantly cruising at 111
KTAS corresponds to Mach 0.1765. Set this in the TAS window as shown below:
In the CAS window locate the pressure altitude, which is 8070’ and read the calibrated airspeed, as shown
below:
The result is ~100 KCAS, which is exactly what we got using the slow airplane procedure. So both
procedures clearly work for the C-172P. Now let’s find out what happens if we use the slow airplane
procedure for the King Air problem.
Page 131
Navigation for Professional Pilots
In the pressure altitude window set the temperature of -30°C over the pressure altitude of 23,000 as
shown below:
Now locate the TAS of 276 on the outer scale and read the CAS. This is shown below:
The value of less than 192 is obviously wrong. We know the correct value is 196. The four knot error may
not seem like a big deal, but it is certainly enough to get the wrong answer on your ATPL written exams.
The error gets larger as you fly higher (as in jets.) So we have confirmed that we cannot use the slow
airplane procedure for the King Air.
Page 132
Navigation for Professional Pilots
Sample Questions 5
Use the “Professional Method” to complete the last two columns of the table below:
Read the section labeled “Old” Method on page 21 of the CR Handbook. Repeat the calculations
using the old method. This time you do not need to determine Mach number:
105 12°C
105 -20°C
145 5°C
235 -12°C
380 -56°C
440 -56°C
Page 133
Navigation for Professional Pilots
0.16 8,500
0.17 8,500
0.224 6,000
0.373 21,000
0.67 32,000
0.775 38,000
Page 134
Navigation for Professional Pilots
Page 135
Chapter 6
The Canada Flight Supplement
The Canada Flight Supplement (CFS) is one of the most important documents for flight planning. You must
become familiar with all the information it contains and be able to locate what you need quickly and
efficiently.
The most used part of the CFS is section B, which gives data about all the registered airports and
aerodromes in Canada. However, to get maximum value from this data you must use the index in the
general section, part A. Get to know the codes used to describe public facilities (PF) lighting, etc. You will
be given a number of assignments to develop expertise in decoding the CFS.
As mentioned previously the CFS contains many useful pieces of information in the later sections. This
includes preferred IFR routes for both high and low altitude. In the assigned cross country flights you will
need to consult these. These can be found in section C, Flight Planning.
Section D contains a lot of useful information about the location of navigation radios, VOR/DME frequency
allocations etc.
Section E is perhaps the most neglected yet vital section. It contains various emergency procedures such as
intercept orders and procedures in the event of an emergency landing. Every pilot should read and
understand this section.
Become familiar with all the information in the CFS. Expect questions drawn from the CFS on all your
exams.
Page 138
Chapter 7
Navigation Theory
In this section you will learn about the compass, the shape of the earth, maps and globes and other theory
elements that impact on navigation.
The earth spins around an axis that astronomers can locate. This defines the north and south poles. We
will learn about the magnetic North and South Pole later. For now simply realize that the true North and
South Poles are based on the spin of the earth and are NOT the same as the Magnetic Poles.
The original definition of the metric distance unit “meter” was that the distance from the equator to the
pole is 10 million meters, i.e. 10,000 Km. Therefore the circumference of the earth is 40,000 Km measured
around the poles. Because the equator is a bit fatter, as mentioned above, the equatorial circumference is
40,076 Km.
The aviation unit of distance is the nautical mile, which is also defined in accordance with the
circumference of the earth. Every degree of latitude is by definition 60 NM, so the circumference of the
earth is 360 x 60 = 21,600 Nm, measured around the poles. The distance around the equator is an extra 41
NM.
From the above discussion you should memorize the definition of the nautical mile and take note that the
difference in circumference of the earth around the poles vs. the equator is less than .00002%. If the earth
was shrunk down to the size of a billiard ball it would be a smoother rounder billiard ball than any you will
find in a pool hall.
The earth spins around an axis that runs through the north and south poles. It spins once every 24 hours,
which defines one day. Due to the gravitational effect of the moon and sun the earth’s spin is gradually
slowing down, but it will take billions of years before it stops spinning relative to the sun. The rate of
slowing is however enough for atomic clocks, such as those in GPS satellites, to measure so they must be
resynchronized with the rotation of the earth every 1000 weeks (roughly every 20 years.) Other clocks are
synchronized just before midnight on December 31 each year making the last day of the year the longest
by a few millionths of a second. An interesting anomaly that results from this variant resynchronization is
that earth clocks and GPS clocks move out of synchronization over the 1000 week GPS cycle. A computer
program in your GPS receiver calculates the difference so that the time displayed to you is approximately
equal to earth time, and different than “GPS time.”
Latitude
Navigation for Professional Pilots
A grid system known as latitude and longitude has been devised so that the location of any spot on the
earth can be specified, rather like the (x,y) Cartesian coordinate system you already know. Take note that
the latitude/longitude system is devised on a model of the earth that assumes a perfect sphere. As
mentioned above the earth is not a perfect sphere, but the difference is such a tiny fraction of 1% that it
can be ignored for our purposes.
Lines of latitude run around the earth east to west and exactly parallel to each other and perpendicular to
the earth’s axis of rotation. Latitude is measured as the angle from the center of the earth with the
equator defined as zero degrees, and therefore the North Pole is 90°N latitude and the South Pole is 90°S
latitude. This is shown in the diagram below.
Every degree of latitude is 60 NM. The subunits of latitude are called minutes. There are sixty minutes per
degree, so each minute of latitude is one nautical mile.
If you know the latitude of two places you can calculate the north/south distance between them. Castlegar
is at N49 17.76 while Prince George is N53 53.37 (note the format, more on that shortly.) The difference is
Page 140
Navigation for Professional Pilots
4 degrees 35.61 minutes. 4 degrees equals 240 NM and 35.61 minutes equals 35.61 NM so the total
distance is 275.61 NM. Please note that this is the north/south distance only, there is also an east/west
component that we turn to next.
Longitude
Because the earth has poles there was no controversy about setting up a latitude system. The lines of
latitude run parallel to each other and are equidistant apart. But there is no equivalent to the equator to
act as a starting point for a grid system in the perpendicular orientation. All locations on the earth are
equal in the sense that the earth spins once per day so every spot on earth has a noon and a midnight,
these are different for each location.
In the historical period when accurate measuring of the earth first became possible the British were the
dominant world force, therefore the PRIME MERIDIAN runs through London England, specifically the
Greenwich observatory. Meridians of longitude are straight-lines that run north/south through the poles.
Every location on the earth has one, but the one that runs through Greenwich is designated as 0°
longitude. Every other location is therefore specified as east or west of the Prime Meridian with 180E or
180W (the same place) being the maximum longitude. 180W is about the middle of the Pacific Ocean, and
runs very close to New Zealand, so it is true to say that New Zealand is on the opposite side of the earth to
England. Castlegar is W117 37.95, i.e. 117 degrees and 37.95 minutes west of the Prime Meridian.
Meridians of longitude DO NOT run parallel to each other. Every one passes through the North and South
Poles, so the distance between them is zero at the poles. What is the distance between them at the
equator?
Based on the model of the earth that says it is a perfect sphere the distance between lines of longitude at
the equator is 60NM. What is the distance between lines of longitude in Castlegar?
Page 141
Navigation for Professional Pilots
Castlegar is at N49 latitude and so is Gander Newfoundland. The picture above shows a view of the globe
from above the North Pole, the outer ring represents the equator, so both Castlegar and Gander are on the
th
49 parallel of latitude. The diagram is drawn to scale, so it might seem odd to you that N49 is closer to
the equator than the North Pole, but a sphere’s circumference does not vary linearly, it varies with the
cosine of the latitude.
Castlegar is at W117, which means it is 117° west of the prime meridian in Greenwich England (Greenwich
is about N52 latitude, but that doesn’t matter.)
Gander is only 54° west of Greenwich, so it is a lot closer to England than Castlegar. Between Castlegar
and Gander the difference is 63° degrees of longitude. How many nautical miles is that?
If Castlegar and Gander were on the equator each degree would be 60NM so it would be easy to figure
how far apart they are. But clearly each degree of longitude is less than 60NM in Castlegar. The distance
between degrees of longitude is given by: 60cosine(latitude). The cosine of 49° is about .66 so each degree
of longitude equals ~39 NM at that latitude. The distance from Castlegar to Gander is 2598 NM.
Page 142
Navigation for Professional Pilots
Given the latitude and longitude of any two places on earth the distance between them can be estimated
using Pythagoras theorem. The diagram below shows two points marked by Xs and the east-west distance
10
(EWD) and north-south distance (NSD) between them. NSD is very easy to figure out as we have seen.
EWD is almost as easy to figure – you should use the mid-latitude between the two points when taking the
2 2 0.5
cosine of the latitude. Distance is simply (EWD + NSD ) .
The ENL has a latitude-longitude calculator that uses the above formula. It also determines true track
between the points, but we will defer discussion of that until we examine some map theory.
Great-circles
A Great-circle is a circle on the surface of the earth whose center passes through the center of the earth.
10
The technical term for EWD is “departure.”
Page 143
Navigation for Professional Pilots
The equator is a Great-circle but the other lines of latitude are NOT.
An important fact about Great-circles is that, except for the meridians and equator, they change direction
(angle) relative to true north as you fly along them. To visualize look at the diagram below and remember
that true track is the angle between meridians and the desired track (DTK.) Any eastbound flight must
change heading to the right continuously to stay on the Great-circle. A westbound flight must continuously
turn left.
Small Circles
Any circle on the surface of the earth whose center does not pass through the center of the earth is a small
circle. An important point to note here is that no circle can be drawn on the surface of the earth that is
larger than a Great-circle, so all other circles are smaller than Great-circles, hence the name.
Page 144
Navigation for Professional Pilots
All the parallels of latitude except the equator are small circles. Is a segment of a small circle the shortest
th
distance between two points? For example the 49 parallel runs from Trail to Vancouver, and can be
visually seen in flight because the trees have been cut down along it. If you fly this line, on a true heading
of 270°, is that the shortest distance between Trail and Vancouver?
th
The answer is no. Imagine that the 49 parallel as a ring resting on the globe (see photo above); it is a
small circle. Imagine what you must do to change this small circle into a Great-circle. You must enlarge the
circle and rotate it so its center passes through the center of the earth (and keep Trail and Vancouver as
th
points on the circle.) In the process the Great-circle line would arc north of the 49 parallel. Following this
Great-circle track would be the shortest route to Vancouver, but you would no longer be able to fly a
constant heading. We turn to that matter next.
Page 145
Navigation for Professional Pilots
Convergence
Convergence is the angle that a Great-circle track changes over its length. In the above diagram DTK 1 is
030° and DTK4 is 100° so convergence is 70°. The pilot must change heading by 70° from the start of the
flight to the end in order to follow the Great-circle route.
A flight along the equator (latitude 0; sine (0) is 0) has no convergence, but a flight near the poles has a
great deal (sine (90) is 1, so convergence equals change in longitude at the poles.) A flight from Castlegar
to Gander has a convergence of _______. Try to figure it out yourself before turning the page. The lat and
long of each airport is given above.
What is the convergence between Castlegar and Vancouver? Longitude in Castlegar is W117 and
Vancouver is W123 (difference of 6°.)
To fly a Great-circle from Castlegar to Vancouver the true track start as 272.25°, half-way the track is 270°
and as the airplane flies into Vancouver the track is 267.75°. The total change in heading is 4.5°, and as
previously noted a westbound flight must change heading to the left.
Try to figure out for yourself the initial, mid, and final heading to fly the Great-circle from Castlegar to
Gander.
Most pilots would say that it is much more convenient to fly on constant heading for the entire flight
however. We turn to that point next.
Rhumb-Line
A Rhumb-line is a constant-track line between two points. In other words it is a line that crosses all the
meridians along the route at the same angle.
The advantage of a Rhumb-line is that you can fly one true-heading (TH) to get from departure to
11 th
destination . In the Castlegar to Vancouver example above, following the 49 parallel, and maintaining a
11
Note that the magnetic heading will still change if variation differs along the route (as it usually does.)
Page 146
Navigation for Professional Pilots
true heading of 270°, constituted flying a Rhumb-line. Pilots generally find this much more satisfactory
than constantly changing heading as they must to fly a Great-circle.
The distance penalty for flying a Rhumb-line as opposed to a Great-circle is not significant for flights up to
500 NM at moderate latitudes (i.e. flights not near or over the poles.) Therefore on short flights pilots
routinely fly Rhumb-lines. On longer flights, such as international airline flights, a Great-circle can be
approximated by plotting a series of checkpoints along the Great-circle 500NM or less apart and then
flying Rhumb-lines between them.
In the above diagram a long-range airline flight approximates a Great-circle by flying over a series of
checkpoints (Xs) along the Great-circle but a constant heading is flown between these checkpoints. I.E. a
Rhumb-line is flown between the checkpoints. The pilot has a nav-log showing checkpoints and one
heading between checkpoints (just what pilots like.) In the days before flight management systems (FMS)
this was the normal navigation method. Modern FMS makes accurate navigation along Great-circles
feasible, and that is now the norm.
Notice that the Great-circle track is ALWAYS closer to the pole than the Rhumb-line, or if you prefer, the
Rhumb-line is always closer to the equator. Remembering this will help you figure out which way heading
must be adjusted to fly a Great-circle.
Map Theory
Now that we know all about Great-circles and Rhumb-lines it is time to talk about maps. It is not practical
to flight plan using a globe, and we certainly can’t take one in the airplane, so we need a map, which is a
flat piece of paper representing the surface of the earth. Obviously there is a problem because the surface
of the earth is curved, NOT FLAT. Imagine cutting open a tennis ball and trying to spread it out flat. You
Page 147
Navigation for Professional Pilots
could not do it. Therefore ALL MAPS ARE DISTORTED. The method of creating the map determines what
type of distortion, but all maps are distorted. All maps are created by “projection” which you can visualize
as meaning that a glass globe is created with all the surface features on it. A light is placed at the center of
the globe and photographic paper is then held over or wrapped around the globe. The surface features of
the earth are therefore projected onto the photograph and a map is created. The only difference between
one map and another is the way the photographic paper is wrapped around the globe.
The dominant projection used in Aviation is the Lambert Conformal, Conic projection. In Canada it is used
for:
The other projection that is widely used is the Transverse Mercator. In Canada it is used for:
Polar charts
Page 148
Navigation for Professional Pilots
The photo above is from a Vancouver VNC chart, commonly used for VFR navigation. Circled is the note
that it is a Lambert Conformal Conic Projection. Lambert is the name of the person who invented it. We
will examine what conformal and conic mean.
The word “conform,” according to the dictionary means: “to be similar or identical.”
A conformal map is one that shows the earth in the same shape that it has in the real world. We already
said that this is impossible however, so a more technical definition is needed. A map is conformal if at
every location on the map the scale distortion north and south equals the scale distortion east and west.
Lambert’s conic projection comes very close to meeting this standard. It is not perfect, but good enough to
be designated conformal. On a perfectly conformal map a straight-line is a Great-circle. On a Lambert
Conformal Conic projection a straight-line can be accepted as “close enough” to a Great-circle for
navigation purposes. The error is less than 0.5%.
To be useful a map must have a scale. You obviously don’t want a map that is as large as the earth. The
photo above shows the scale on a VNC is 1:500,000, which means that one inch on the map equals
500,000 inches in the real world (1cm equals 500,000 cm etc.) 500,000 inches equals 6.9 NM so one inch
on the map equals 6.9 nautical miles.
On a perfectly conformal map the scale is constant throughout the map, but real maps are never perfectly
conformal. The scale of 1:500,000 is therefore the average scale of the map. In the middle of the map it is
a bit more, but near the top and bottom it is a bit less. The difference is less than 0.5% and therefore you
can ignore it. Let’s see why there is an error at all.
Page 149
Navigation for Professional Pilots
Imagine a sheet of photographic paper formed into a cone and set over the globe (like a hat) with its apex
at above the North-pole. This would be a standard conic projection, and it would touch the earth along
only one parallel of latitude. Lambert’s innovation was to sink the cone into the earth so that it touches
along two parallels of latitude, as shown in the photo above. Between the standard parallels the surface of
the real earth is above the cone, and north and south of the standard parallels the surface of the earth is
below the cone. The consequence of this to map scale is shown below.
Page 150
Navigation for Professional Pilots
The diagram above shows projection lines emanating from the center of the earth and passing through the
surface of the earth and the map. It is important to consider where a given point on the actual surface of
the earth appears on the map. North and south of the standard parallels points on the map are further
apart than on the earth’s surface (if you measure a distance of say 100 NM on the map the real distance
on the surface of the earth is less.) Between the parallels the opposite effect takes place. Along the
standard parallels the scale of the map is precise.
The photograph at the beginning of this section showed that the standard parallels for the Vancouver VNC
are N49 20 and N54 40. Along these lines map scale is accurate. As stated previously the scale error over
the entire map is about 0.5% so you can feel free to measure distance anywhere on the VNC for navigation
planning purposes. Different standard parallels are used on VNCs to suit the latitude of the area depicted.
Because Rhumb-lines are not straight, if you want to fly a Rhumb line you must measure the true track at
mid-leg. At mid-leg a Rhumb-line track and a Great-circle track are equal.
Page 151
Navigation for Professional Pilots
Originally Mercator projections were developed for use near the equator. The Lambert Conic projection
does not work for areas near the equator.
In the original Mercator (not a transverse Mercator) the photographic paper is rolled into a cylinder rather
than a cone. This cylinder is wrapped around the earth so that it touches along the equator.
On the Mercator projection the lines of latitude and longitude come out perpendicular to each other. This
has the advantage that a straight-line drawn on the map is a Rhumb-line, but the map is NOT
CONFORMAL. In other words it distorts shapes, and a straight-line is NOT a Great-circle.
At the equator the lines of longitude and latitude really lie perpendicular to each other so the Mercator
map is relatively conformal near the equator; but is not useable in Canada.
The Transverse Mercator also wraps the globe in a cylinder but it is rotated 90 degrees so that it touches
the earth along a meridian of longitude rather than the equator. The cylinder can be rotated so that it
touches on any of the 360 meridians. The map scale is accurate only along the reference meridian.
Page 152
Navigation for Professional Pilots
A transverse Mercator map is NOT conformal, but as long at only a small section, close the reference
meridian, is used the distortion is minor. It has the advantage of creating a grid in which lines of latitude
and longitude cross perpendicular to each other. Consequently a straight-line drawn on the map is a
Rhumb-line.
The Transverse Mercator projection is only suitable for small scale maps such as terminal charts. It is used
for VTA and IFR terminal charts.
st
In the 21 century as GPS navigation becomes dominant it is probable (or at least possible) that true tracks
and true north will become the only references used for navigation. But, not all airplanes have such
equipment today, so a magnetic compass must be used. Unfortunately the Magnetic North Pole is not
collocated with the real North Pole. The photo below shows the location of the Magnetic North Pole.
Page 153
Navigation for Professional Pilots
A compass points at the Magnetic North Pole. A compass on the white line in the photograph also points
at the true North Pole. But a compass in British Columbia, as shown in the photograph, points too far east.
The error is called variation, and it is the angle between true north and magnetic north. The variation
shown in the photograph is easterly; in Montreal variation is westerly. On a line running through Manitoba
there are locations where variation is zero (as shown in the photograph.)
An isogonic line joins locations with equal variation. All aeronautical maps have isogonic lines printed on
them. These lines are labeled as shown in the photo below.
Page 154
Navigation for Professional Pilots
In flight the heading indicator is normally set to magnetic north and all heading are referred to as
magnetic headings. Flight planning is normally done in true however, so true heading must be converted
to magnetic before the flight. The following rhyme may help you remember whether to add of subtract
variation.
This means that when variation is easterly the magnetic heading is always less than true heading. When
variation is westerly magnetic heading is always more than true.
Even though the above rhyme is fairly simple it is best to use your CR to convert between magnetic and
true so that no mistake is made. This procedure was demonstrated previously.
Compass Deviation
The topic of deviation is out of place here since it is not related to map theory, but it does fit logically here
because of its relationship to variation. Deviation is an error in the compass of the airplane. As such
deviation is specific to an individual airplane. It is caused by the magnetic fields of the metal parts of the
airplane and is significantly affected by electrical equipment such as the alternator. These things cause an
error in the compass known as deviation.
Deviation changes from time to time. That is to say that the magnetic field of the airplane changes over
time. Consequently it must be measured and recorded on a regular basis. The process of measuring
Page 155
Navigation for Professional Pilots
deviation is called a compass swing. A compass swing is required every year and also any time electrical
equipment is removed or replaced in the airplane.
An AME performs the compass swing and provides a compass card in the cockpit which the pilot uses to
correctly set the heading indicator. The pilot should read the compass then the deviation card and set the
heading indicator to the corrected magnetic heading.
Deviation is seldom more than 2 or 3 degrees so ignoring it, as most pilots do, results in only minor error.
Contour lines are lines that join points of equal elevation above sea level.
The above photo shows contour lines on a VNC. On VNC charts there is a 500’ contour but from 1000’ and
above contours are every 1000’. The contour interval is described at the bottom of the Hypsometric scale,
explained next.
To make terrain easier to visualize Hypsometric tinting is used, according to scale below:
Page 156
Navigation for Professional Pilots
The above scale is found on the white edge of every VNC. At the top of the scale you find the maximum
elevation for the map. The example above is 19,524’ asl, the highest point in Canada; located at N60 34
W140 24, also shown just above the hypsometric tint scale.
A 500’ intermediate contour line appears within the lowest hypsometric tint, and intermediate contours at
4000’, 6000’, 8000’, 10,000 and 11,000 are also plotted. Use these to refine the information provided by
the tinting.
Map Legend
Every map has a legend printed along the edge that shows all the symbols used on the map. All the
symbols are important but will not be covered here as you can read the legend for yourself.
Page 157
Navigation for Professional Pilots
Airport data is provided on VNC charts but this should only be used for preliminary planning. Always look
in a current CFS for up-to-date airport data.
Map Scale
The scale of the map is always printed on the map. The picture below shows the scale on the Vancouver
VNC chart is 1:500,000. The same scale is used on all VNC charts in Canada.
WAC charts use a scale of 1:1,000,000. VTA charts have a scale of 1: 250,000.
An appropriate Navigation ruler must be used to measure distances on these maps. Make sure you use the
correct scale. Always measure distance in Nautical Miles, not statute miles. The inner scale is used on VNC
and the outer scale on WAC charts. For a VTA chart use the VNC ruler scale then double the distance.
Grid Navigation
The picture below is of a globe from above the North Pole. Imagine you wish to fly from the checkpoint
marked as departure to the one marked as destination. What is the true track?
Page 158
Navigation for Professional Pilots
If you are willing to fly a Rhumb line, then heading of 090 true would take you to the destination along the
line shown below:
But this is clearly not the shortest route. The desired route is “over the pole.”
Page 159
Navigation for Professional Pilots
In the diagram below the desired Great-circle route is drawn in as well as some lines of longitude for
reference. We already know that in order to fly a Great-circle we must change heading as we fly, make a
table of required true headings for the locations marked with the Xs. Remember that each line of longitude
represents a true track of north (0°.) I.E. you must orient your Douglas protractor to north on each line of
longitude.
X1 019
X2 045
Page 160
Navigation for Professional Pilots
X3 082
X4 137
X5 160
Imagine what would be happening on the flight deck as you make this flight. The airplane departs on a
heading of 019° (essentially northbound) and flies a straight-line. But, the heading indicator must be
adjusted so that as the airplane passes X2 it reads 045°. At X3 the HI is rotated to 082°; at X4 to 137°.
When the airplane arrives at destination it has made no turns, but the heading must be 160° true
(essentially southbound.) For ideal effectiveness HI would be continuously updated for convergence, in
practice it is usually updated every 6° change in longitude.
Every flight over the poles starts off “northbound” and finishes “southbound.” Pilots must accept that
brain teaser, but grid navigation eliminates the need to continuously update the HI enroute. Examine the
diagram below.
Page 161
Navigation for Professional Pilots
A rectangular grid is laid over the pole as shown in the diagram above. This grid can be oriented to by
reference to any meridian, but the standard procedure is to use the Prime meridian as the reference.
To use the grid simply put your Douglas protractor on the grid with north aligned with the Prime meridian.
For the track in the example the track is 219G (read “219 Grid.”)
Examine the diagram to convince yourself that the Grid heading is simply the true heading plus west
longitude, or minus east longitude.
The 160E median has been labeled in the diagram. You should label the other meridians corresponding to
X2, X3, X4, and X5.
Page 162
Navigation for Professional Pilots
To use Grid navigation, as the airplane approaches the departure point (it probably took off somewhere
much further south) the pilot switches the HI to grid. This amounts to rotating the HI an amount equal to
the longitude of the airplane. In practice grivation is applied to the magnetic compass.
Once the HI is adjusted to Grid the pilot can maintain a constant heading for several hours (in the example
s/he maintains 219°.) Even though this is usually considered a southbound heading the airplane is
obviously still heading north. But things will work out in the end. The pilot holds this grid heading for a few
hours until arriving at the destination (point where the transition back to magnetic headings will be made)
at which point the heading is reset to magnetic by changing it from 219 to about 160° plus variation. Note
that despite all these adjustments the airplane actually flies a straight line the whole time.
Grivation
Grivation is by definition the difference between magnetic track and grid track. As previously noted the
difference between true and grid tracks equals the longitude (from the reference meridian.) Therefore
mathematically grivation equals longitude plus variation. Lines on a map joining points of equal grivation
are called isogrivs. Pilots can use these to set the HI to Grid the same way they use variation to set the
compass to true. However, the magnetic compass is quite unreliable in the extreme Polar Regions so it is
much more common to use INS as the reference (the INS “knows” the airplanes true track) eliminating the
need to use grivation. The two relevant equations are:
You will examine grid navigation a bit more in Avia 240. For now this simple introduction to the concept is
all that you need. You should see that grid navigation is necessary because of the extreme amount of
convergence in polar crossings.
Keep in mind that basing the grid to the Prime meridian is arbitrary. For some purposes it could be
preferable to establish a grid based on a different meridian. For a Canadian arctic survey expedition might
find it desirable to have a grid oriented to a meridian within Canada. Can you see the benefit of this? If
they used the Prime meridian instead what direction would it be to fly from the Yukon to Greenland (east
or west)? When they are done exploring the polar region do they fly north or south to return to
Vancouver?
Page 163
Navigation for Professional Pilots
In the above diagram radial 1 represents one LOP and radial 2 is the second. Where they cross is the
“fixed” position, or fix for short. Pilots frequently refer to the procedure as taking a fix.
The process is quite straight forward, but there are a few important details. Most importantly fixes should
be plotted using true bearings, not magnetic. But, most VORs are oriented to magnetic north, which
means the nav radio tells you the magnetic radial you are on. Let’s say in the above example that radial 1
is 010R and radial 2 is 290R. You CANNOT put a protractor on each VOR and draw two lines based directly
on these bearings. Each radial must be converted to a true bearing by applying variation. What variation
should be applied to radial 1; which to radial 2? Choose your answer before reading the next paragraph.
The important thing to realize is that you must apply the variation at the VOR, NOT at the airplane.
Therefore radial 1 must be adjusted by 12° and radial 2 by 10°. Use the wind side of your CR to make sure
you don’t make any mistakes.
Page 164
Navigation for Professional Pilots
In the above photograph the 010R is set across from 12E variation. The true course is clearly 022°. Repeat
the same process for 290R with variation 10E to confirm the true course is 300°.
Plot the two tracks 022 and 300 by putting a Douglas protractor over each VOR in turn and aligning it with
meridian 1 and 3 respectively. Draw the lines carefully to find the fix.
To obtain an LOP from a VOR it is essential to center the CDI needle with a FROM indication. This gives a
direct reading of the radial. If you center the needle with a TO indication you need to take the reciprocal
(but it is safer to simply rotate the OBS knob until a FROM flag shows.) In the arctic VORs are oriented to
true north, which eliminates the need to make the conversion demonstrated above. It is could be the case
that you must plot a fix based on one VOR in magnetic and another in true. This is not difficult, just be
careful to convert the magnetic radial to true while making no adjustment to the true radial.
Do not attempt to plot a fix by extending the markings on the compass roses on the VNC. These are not
accurate enough.
IMIPORTANT. The legend of your VNC and LO chart warns you that in some cases VOR symbols are offset
from their actual position, but the compass rose is centered on the actual location of the station. Check
this carefully to ensure you are plotting the fix from the actual location of the VOR.
Expect to see questions of the above type on Transport Canada’s Commercial Pilot Written exam. Watch
for tricks such as offset VOR locations (previous paragraph) and mixed magnetic and true VORs (also
mentioned above.)
Now we will consider the process of establishing a fix based on bearings from two NDBs. There are two or
three differences to note, but the overall process is the same.
Page 165
Navigation for Professional Pilots
The diagram below is deliberately identical to the one above expect that the VORs have been replaced
with NDBs. The first difference to think about is the process by which the pilot determines what bearing 1
and 2 are. How is this done? Formulate your answer before reading the next paragraph.
The basic process of obtaining a bearing from an NDB is the same regardless of the equipment the
airplane has, but it is much easier with an RMI than with a fixed card ADF (Note that if you have a GPS this
whole process is redundant since it will provide your current latitude and longitude, which you can plot to
fix your position without the need to do any of this process. We therefore assume you have no such
equipment available.)
With an RMI read the bearing from the tail of the RMI needle. Good airmanship demands that you confirm
the HI is set accurately before accepting this bearing. Usually the HI is set to magnetic so the bearing is a
magnetic bearing. If you happen to be flying in the arctic with your heading indicator set to true then the
bearing is true. And if your HI is set to grid you have a grid bearing.
If you have a fixed card ADF you must follow the usual procedure to convert relative bearing to magnetic
bearing. MB = RB + Heading.
Since the diagram above is identical to the previous VOR based one, and the airplane is in the same
location, you may expect that the magnetic bearings will be 010 and 290. They will NOT be. Think why
before reading the next paragraph.
Page 166
Navigation for Professional Pilots
In reality an ADF may not be accurate enough to detect the theoretical difference here, but the radio wave
from the ground stations come to the airplane along straight-lines corresponding to Great-circles (both
VOR and NDB.) This amounts to saying that the true bearings will be the same, but not the magnetic
bearings. The variation correction for the VOR is applied at the station, while that for the NDB is applied in
the airplane. Therefore both NDB bearings must be corrected by 11E. Go back and examine the VOR
example above if you have forgotten which variation was applied in that case. Therefore magnetic bearing
1 is 013 and bearing 2 is 289 magnetic. Correct each of these magnetic bearings by variation of 11E exactly
as described above for the VOR case. What values to you get?
Once again the true bearings are 022° and 300°. Plot these exactly as before to get the fix.
Summary: When plotting a fix convert all bearings to true. Apply variation at the station for VOR and at
the airplane for ADF. Use the CR for converting between true and magnetic to avoid mistakes. Use a
Douglas protractor centered on the station to plot the true bearing. Make sure the protractor really is
centered on the station by checking the compass rose. Extend the lines until they cross, giving you a fix. On
a Lambert Conic chart the straight-lines are Great-circles, which correspond to radio waves so this
procedure works. On a Mercator chart straight-lines are Rhumb lines so an error equal to convergence is
introduced, which you must correct for. Fortunately Mercator charts are only used for VTA and T charts in
Canada, where position fixing is an unlikely procedure.
It is quite possible to obtain a fix from one VOR and one ADF bearing. The process is identical to that
described above. Just remember where to apply the variation. Watch out for combinations of true,
magnetic, and grid navaids, especially on exams.
Page 167
Navigation for Professional Pilots
Page 168
Chapter 8
Flight Planning
In this section we will take all the knowledge we have developed and use it to plan flights. It must be
stated that we presume that dead reckoning (DR) will be the dominant form of navigation, with pilotage
used only for brief periods usually on departure and arrival. In the section on mountain flying toward the
end of the text some comments about planning for a flight when pilotage is dominant are included.
Definition of a Leg
All flights are broken into legs. A leg is a defined path the airplane follows. Most legs are either straight-
lines or arcs. Future navigation systems may define paths that have more complex shapes, but that is
beyond the scope of this text.
Modern flight management systems (FMS) are programmed by entering a series of legs beginning at the
airport of departure and ending at the destination. The entire route must be input as a series of
continuous legs with no breaks at any point. The FMS computer recognizes a variety of leg types, which
the pilot selects from a menu. When a flight is fully defined by a series of legs with no breaks we say the
flight plan is closed.
If a waypoint is designated Fly-over, you must fly directly over it before turning to the next leg. At a Fly-by
waypoint you start to turn prior to the waypoint so that you intercept the next leg without overshooting it.
You should normally treat waypoints as Fly-by unless they are specified as Fly-over. An exception is when
using NDBs as waypoints, without GPS for assistance. It is far too easy to be misled about station passage
with an NDB so it is preferable to treat all NDBs as Fly-over waypoints.
In recent years it has become very common for aircraft to be equipped with GPS and or other types of
precision navigation equipment that provide extremely accurate range information. These systems provide
horizontal distance rather than the slant range the older DME systems provide. When the pilot has this
type of instrumentation available it is possible to precisely determine when to turn for a Fly-by waypoint.
The diagram below shows the required formula. The equation r=.0053 is fully explained in the
aerodynamics text Aerodynamics for Professional Pilots.
Page 170
Navigation for Professional Pilots
The formula might not seem user friendly but all you have to do is calculate .0053TAS once and memorize
it. You already have memorized values for the sine of several angles for the purpose of estimating drift (see
page 50.)
To calculate .0053 TAS take TAS and divide by 100 then divide by two. For example if your airplane cruises
at 120 knots divide by 100 to get 1.2 then divide by 2 to get 0.6. Remember this number. When
approaching a 90° turn lead by 0.6NM. For a 45° turn lead by 70% of 0.6, i.e. about 0.4NM, etc.
Introduction to Nav-logs
A nav-log is a document that helps you organize your flight planning so that you don’t forget any
important details. It should chronicle your entire flight from takeoff to destination and then to the
alternate airport if IFR. A nav-log should also include time and fuel allocations for contingencies
(unavoidable delays due to weather, traffic, etc.), approaches, and reserve (reserve is a legal as well as
practical requirement.)
In this course you will prepare nav-logs both electronically and manually. On your commercial pilot flight
test you are required to prepare the nav-log manually, and of course exams, most assignments, and ALL
quizzes and tests in this course require manually generated nav-logs. On your actual cross-country flights
and simulator exercises you are encouraged to use the ENL because it is quicker, easier, neater, and less
Page 171
Navigation for Professional Pilots
likely to contain math errors. You were introduced to the ENL when we examined cruising altitudes,
although we only scratched the surface on using it. Further details are provided later.
Nav-logs are usually laid out in a grid with columns representing the parameters to be evaluated (planned)
and with rows representing “legs.” .
1. Departure legs
2. Enroute legs
3. Arrival legs
4. Approach
6. Enroute to alternate
7. Arrival at alternate
8. Approach at alternate
All these groups are needed for every IFR navlog. Groups 5 to 8 are not needed for VFR navlogs.
On Selkirk College navlogs the departure, arrival, and approach leg groups are usually simplified so that
one line on the navlog represents the entire group. We normally group the arrival legs with either the
enroute or approach. The approach group is normally reduced to a single leg (for both IFR and VFR
navlogs.)
Departure legs can also be called “climb legs.” The departure legs end at the Set Heading Point (SHP.) The
SHP is usually specified in an IFR departure procedure, but must be chosen by the flight planner for VFR
flight. Advice on choosing a SHP is given below. There is a variable point at which the airplane reaches top
of climb which is conveniently labeled as top of climb (TOC.) TOC may come before or after SHP. If after
then it is technically part of the enroute group. On occasion TOC and SHP are the same point. Some VFR
pilots find it convenient to “rig” the situation so that this happens. In this case label the point as SHP or
SHP/TOC (preferred.)
The largest part of most navlogs consists of several enroute-legs (also called cruise-legs.) These legs run
from turning point to turning point. i.e. a new leg should start at every point where the track changes.
The arrival legs end at an initial approach fix (IAF) for IFR flight plans. For VFR flight plans arrival legs end
when the aircraft joins the circuit at the destination airport. Sometimes it is expedient to just treat these
legs as cruise legs rather going to the trouble of estimating the reduced fuel flow used during the descent.
Page 172
Navigation for Professional Pilots
Selkirk College nav-logs also contain rows allocating time for contingencies, and reserve (both explained
below.)
There is logic to the order that navlog rows are laid out that results in the pilot having the required
information at hand in flight to make decisions about fuel status. Consider the nav-log below, which is for
a flight in a Beech 95. Even though you have never flown one before answer the following questions by
referring to the nav-log.
1. As you taxi out in Calgary your fuel quantity should read _________ gal.
2. As you pass YNY your fuel quantity should read ________ gal.
12
3. As you reach BOOTH your fuel reads 35 gallons – is fuel remaining as expected?
4. Upon arrival at BASRA, if ATC requires you to hold (perhaps because a runway is closed) your
contingency fuel is used up when your fuel gauges read _______ gal (assume you wish to retain
13
50 minutes reserve.)
Notice that you can answer these questions quite easily because of the logic by which the nav-log is laid
out.
12
No. You are supposed to have 37.8, so either the gauges are not accurate, or you have used a couple of
gallons more than expected. You should assume the later.
13
27.2
Page 173
Navigation for Professional Pilots
Page 174
Navigation for Professional Pilots
1. The fuel for the trip is specified in advance and you determine consequent reserve
2. You plan for a desired amount of contingency and reserve fuel and determine how much ramp
fuel you need for the flight
If situation 1 applies, begin by filling out the ramp fuel in the upper right corner of your nav-log. As you
complete each leg subtract the fuel used to get fuel remaining; whatever you have when you get to
reserve, which is always the last row, is your reserve. Assess reserve fuel value to confirm that it is
adequate before committing to the flight.
If situation 2 applies, leave ramp-fuel and fuel-remaining blank until all legs have been planned. Fill out the
reserve fuel and work backwards until you determine the required ramp fuel.
The first fixed checkpoint is called the set heading point (SHP) on a DR cross-country and choosing it
requires considerable thought.
For VFR flight you should select a SHP that is easy to locate and relatively close to the departure airport.
Exactly how close depends on several factors:
3. How well you know the area and the SHP checkpoint
On a VFR flight you normally use pilotage to find your way to the SHP. On IFR flights the SHP is usually a
navaid such as a VOR or NDB so finding your way there is straight forward. VFR pilots can also use beacons
and VORs for navigation but before doing so consider whether you will conflict with IFR traffic. It is
frequently safer to choose a visual point rather than a radio navigation point when VFR.
Because pilotage is used to locate the SHP be sure to pick one that has distinctive ground features leading
to it. An ideal SHP is on a road, railway, river, or other similar feature that you can follow to locate it. A
Page 175
Navigation for Professional Pilots
SHP must also be distinct so that you can visually identify it. It must also be small enough to constitute a
point – for example using “the city of Vancouver” as a SHP is not acceptable. Instead pick a particular point
such as the intersection of two major roads, a park on a particular road, etc.
If the ground around the departure airport lacks distinctive navigation features, as is often the case with
small airports in northern Canada, use the airport as the SHP. This is called an “overhead departure.” You
simply takeoff and climb over the airport to set course. Weather permitting you should be 2000agl or
higher when you reach the center of the airport in order to avoid conflict with any circuit traffic. If you
were making a closed navlog the first and third checkpoints would both be the airport and the second
checkpoint would be 1000 feet. In reality you will probably open the navlog and only have one leg, i.e. the
first and second checkpoints will be the airport of departure but the distance flown must represent that to
fly out to 1000 and then return while climbing to 2000.
Traffic congestion is a factor in choosing a SHP for two reasons. In the case of an airport with very little
traffic it is quite feasible to make an overhead departure or use a SHP very close by. The lack of traffic
means that no conflict will result. But, at a busy airport it may not be possible to do an overhead departure
or use a nearby point as SHP; traffic congestion could force you to choose a SHP clear of the airport zone,
i.e. more than 5 miles from the airport. In this case make sure to choose a SHP on a very prominent
pilotage feature that you will have no trouble seeing and flying to. A point on a major road, river, or
shoreline would be a good choice. Of course a radio navigation beacon could also be a practical choice if
the airplane is suitably equipped.
How well you know the area is a factor in choosing a SHP. At an airport you know well you can locate SHPs
that would be too obscure if you didn’t know the area well; for example the intersection of two minor
roads. Keep in mind that some objects that look prominent on a map are in fact quite difficult to see on the
ground. For example locating a radio transmission tower, in daylight, is quite difficult and thus does not
make a good SHP. But, if you know the tower well and can identify it relative to other local landmarks it
may be an acceptable SHP.
Page 176
Navigation for Professional Pilots
Normally the above closed departure would be opened up by collapsing it into two legs, as shown below.
An interesting special case involves setting up the navlog for an overhead departure (remember this means
using the departure airport as SHP) If you are doing an overhead departure the distance flown is certainly
not zero (the straight-line distance) it is likely 5NM or more. An ENL navlog showing an overhead
departure is shown below to demonstrate this.
Page 177
Navigation for Professional Pilots
3. Collapse the departure into one or two legs (more if needed for clarity.)
Once you have the distance use the time fuel and distance to climb chart to figure out what your altitude
will be at the end of leg 1. Estimate the average wind in this calculation. Enter the fuel used and the time
in the appropriate columns of.
In 99% of cases, especially in the mountains, the distance required to climb to altitude will exceed the
distance to the SHP. Therefore the first enroute leg will also be a climb leg (leading to TOC) as described
below.
When using the ENL, for departure legs, estimate how high you will be when you reach the SHP. The ENL
determines distance, time, and fuel. If the resulting distance does not match your estimated distance to
the SHP revise the altitude estimate.
In most cases you do not reach your final cruise altitude before SHP and therefore will be climbing enroute.
The trick is figuring out how far after.
If you did a reasonable job of estimating your distance and altitude to the SHP then the remainder of the
climb must be allocated to this leg. For example if you estimated you would be at 5000 over Robson and
you are climbing to 8500 then this leg is for a climb from 5000 to 8500. Use the charts in your POH to
determine:
1. Time to climb
2. Fuel to climb
3. Distance to climb
Page 178
Navigation for Professional Pilots
The only complication is allowing for wind. It is critical for you to realize that wind will NOT AFFECT time
or fuel to climb, it only affects distance. Don’t move on until you have reasoned that claim out and are
convinced that it is true.
It is necessary to allow for wind in the climb or your flight planning will not be accurate. Wind changes as
you climb so it can be quite different at 5000 than at 8500. In addition true and indicated airspeeds change
as you climb in accordance with the climb charts (previously covered.) We need a rule of thumb to
determine distance covered in a climb.
For normally aspirated piston airplanes such as the C-172P and Travelair rate of climb drops off quickly
with altitude so that mid-time in a climb happens at higher than mid-altitude. You should therefore
determine your groundspeed at 2/3 of the way up to your cruise altitude and calculate distance covered
using that value (remember you know the climb time.) Using the example of climbing from 4500 to 8500
the difference is 4000 feet and 2/3 of that is 2700, so determine GS at 7200 (4500 + 2700.) Once you know
this GS, and given the time to climb, use your CR to calculate distance.
In turbo-charged and turbo-prop airplanes climb rate does not drop off as quickly so determine GS halfway
up to cruise altitude and calculate distance covered based on that (in the example, calculate GS at 6500.)
Once you know how many miles past SHP it is to TOC use your ruler and mark TOC on the map and then
measure the distance from TOC to the next waypoint (mystery lake in the navlog shown above.) This
distance is used on the next leg. In the example navlog the total distance from Robson to mystery lake is
50NM, so the distance from TOC to mystery lake is 37NM.
When using the ENL enter the altitude that is 2/3 or ½ your cruise altitude with wind and temperature for
that altitude. Initially enter the distance from your time to climb chart, but once the ENL calculates
groundspeed and time you will have to increase or decrease the distance until the time and fuel match
what you determined from the climb chart.
Page 179
Navigation for Professional Pilots
(circuit joining point) or in the case of an IFR navlog it is usually the location where the IFR approach will
begin.
Flights should be broken into manageable legs. A 1000 mile VFR leg is hard to fly and is subject to
problems covered previously in map theory. Even transoceanic airliners fly from checkpoint to checkpoint
over the ocean so don’t be afraid to break your trip into manageable legs. On the other hand don’t make
the legs too short or your nav-log will be so extensive it will over-load the airplane. Use your ruler to
measure the length of each leg in nautical miles. Use a protractor to measure the true track (covered
below.) When planning with an LO or HI chart read the distance and magnetic track directly from the chart
and use the CR to determine the true track. For example the LO1 chart below shows the track from CG to
WHATS on R119 is 301°M and the distance is 41 NM. Variation is 18°E (the dashed line just south of
WHATS.)
To get the true track use the back-side of your CR. Set the magnetic track (301M) opposite variation (18E)
as shown below. The true track (TC) is 319.
Page 180
Navigation for Professional Pilots
IFR checkpoints are VORs, NDBs, or intersections; every location where your track changes is a checkpoint
(WHATS is an intersection.)
VFR checkpoints should be distinct geographical features you can positively identify yourself over and
thereby confirm you are on course (and start the next leg accurately.) Towns, airport, small lakes, etc make
good checkpoints. Normally true-track changes (at least slightly) over a checkpoint. Draw a straight line
with a pencil between each checkpoint. Measure the length of the line with a ruler of the appropriate
scale. Measure the true track by aligning your protractor to north with a line of longitude near the mid-
point of the leg.
In cruise TAS speed and fuel flow are in accordance with the cruise performance charts. Be sure to write
the power setting and fuel-flow in the proper column for reference.
Fill in the actual wind and temperature at your cruising altitude and use your CR to determine GS and true
heading based on the TAS. Remember that you will need to determine pressure altitude and or density
altitude to determine TAS.
Fill in the variation and then calculate the magnetic heading. Remember the old saying:
This means that with easterly variation (such as in British Columbia) magnetic heading is always less than
true heading. In eastern Canada, where variation is west, magnetic heading is always more than true
heading. To avoid any chance of a mistake it is safer to use the back-side of your CR when converting
between true and magnetic, as shown in the photo above.
Page 181
Navigation for Professional Pilots
Use your CR to determine CAS, and then use the calibration chart in the POH to determine IAS. You need
this so that you can check in flight that the airplane is performing as planned. Of course you also use the
CR to determine time and fuel for the leg.
All airplanes fly faster, for a given amount of fuel flow, at a higher altitude. However, fuel is used climbing
to altitude, so there is an altitude above which further climb increases the total time for the flight.
The criteria for saying on altitude is “optimum” could be saving time or fuel. Most commercial air
operations place a premium on time rather than fuel. The optimum altitude is therefore either:
1. The altitude that results in the least time for the flight
2. The altitude that results in the least fuel used for the flight
1. Aircraft type
2. Power setting
6. Wind
For piston engine airplanes the benefits of flying at a higher altitude are very minimal in terms of saving
fuel. Only on very long flights is any fuel saved at all – so in most cases you can fly at any altitude you wish
as far as fuel consumption is concerned. Therefore it is best to decide your cruising altitude based on other
factors such as the improved safety of flying higher in a single-engine airplane. Of course it is important to
avoid headwinds, so try to avoid climbing into a strong headwind aloft unless safety demands you do so
(as it often does in British Columbia.) Climbing to high altitude to pick up a strong tailwind is however
always a good idea.
In a turbine engine airplane flying at a higher altitude is much more advantageous. The resons will be
covered in your aerodynamics course. It is very worthwhile for you to examine the cruise performance
Page 182
Navigation for Professional Pilots
charts for the King Air, which you have an FIM for, and calculate the specific range foe the airplane at
various altitude. You will quickly see that it is much better at high altitude
Top of Descent
What goes up must come down, so the saying goes. But with an airplane the pilot has control of when to
come down and this is a matter that deserves more thought than it is sometimes given. If descent is
started too late then the airplane arrives at the airport too high to land and must circle down, wasting
time, or requiring a high descent rate that is uncomfortable for passengers and may cause damage to the
engine in some cases.
The turbocharged engines typical of working airplanes are quite sensitive to large power reductions. The
shock-cooling will damage the engine. Thus professional pilots learn to start descent early enough that a
gentle descent with gradual reductions in power can be made. Conversely, pilots of turboprop and jet
airplanes can close the throttle without fear of damage to the engine. For these airplanes descent is
delayed as long as reasonable in order to take advantage of the better fuel economy at altitude.
In single-engine mountain-flying it is particularly unwise to descend early. The terrain is rugged, with few
places to land in the event of an engine failure. The ideal descent is usually one that reaches circuit altitude
just slightly before joining the circuit. At times it may even be necessary to plan to circle down over the
airport, although this should be avoided if possible.
The most commonly used descent gradient is 1000 feet every 3 nautical miles. This is used by most jet and
turboprop pilots and also works reasonably well in the C-172 and B95. For high performance turbocharged
airplanes a gentler gradient such as 1000 feet every 4 nautical miles may be more appropriate. It is
important for you to get to know what is best for your airplane. Once you have established the ideal
descent gradient designating a top of descent (TOD) is straight forward.
To designate a TOD calculate the altitude to be lost in thousands of feet then multiply by 3 (or 4 as the
case may be.) Assuming you are planning to join the circuit the altitude to be lost is obtained by
subtracting circuit altitude from cruise altitude. If you are planning a straight-in landing then subtract field
elevation from cruise altitude. The value should be rounded to the nearest thousand feet. For example if
descending from 8500 to join the circuit in Castlegar at 2600 you get 6 thousand feet. Multiply 6 x 3 to get
18 Nautical miles. Your TOD is 18 miles form where? The answer is; from the place you wish to reach
circuit altitude. This is likely 3 miles from the airport, so start descent 21 miles out.
TOD should be calculated in flight, but need not appear on your navlog.
Contingencies
RAC 3.13 requires pilots to allow for contingencies when flight planning. Even if no such regulation existed
it would only be prudent to do so. We have already seen that flying at a different altitude than planned
affects required fuel. Obviously the wind can be different than forecast. There are a great many factors
that can affect your flight. The longer the flight the more likely it is that errors in planning will arise, yet it
is the long flights that have the least margin for error.
Page 183
Navigation for Professional Pilots
If you are headed for a small airport with only one runway is there any chance the runway could be
unusable when you arrive there? Of course there is. An airplane could land gear-up while you are enroute,
or any number of other things could happen. It is pretty much a guarantee that these things will happen to
you a few times in your life. If you don’t leave yourself with some options (exactly what contingencies
means) then you will be, as we say, SOL.
Often our flights have lots of options built into them. A flight in a C-172 from Castlegar to Boundary Bay
can equally well land in Langley, Abbotsford, Delta, etc. So a gear-up on a runway in Boundary Bay is not a
circumstance that requires contingency planning. But, you may well have to divert due to weather enroute
and wind up flying farther than planned in the process. Contingency time should be allocated for this
purpose.
The point being made is that allocating contingency time means allocating fuel. Simply ask yourself how
much extra time you might need for contingencies, then calculate the fuel for that time based on cruise
power.
It is important to realize that if you actually need to use your contingency fuel you DO NOT have to burn it
at the “normal” cruise rate. For example if you are holding (VFR you might be circling while the runway is
plowed) you should fly at less than 65% power and thus you would have more contingency time than you
indicated on your nav-log. This is where it is nice to have accurate fuel gauges so you can tell when you are
reaching the end of your contingency fuel. Most turbo-prop and jet airplanes have reliable fuel gauges, but
most small piston airplanes do not.
Note that contingency time should not be included in time enroute you file on your flight plan. Filing flight
plans is covered later.
On the ENL set an amount of contingency time and the ENL allocates the required fuel at the normal cruise
power setting. Note that contingency time is NOT included in time enroute.
Approach at Destination
For VFR flights your last enroute checkpoint is normally the destination airport, i.e. the point where you
join the circuit (if the airport has a published VFR arrival procedure it should be the point where that
procedure begins, as for example in Kelowna or Victoria
For IFR flights the last enroute checkpoint is usually the IAF (initial approach fix) which is where you start
your instrument approach (explained previously.)
Therefore time and fuel must be allocated for the approach, and possible missed approach. If your last
checkpoint is the beginning of the arrival procedure then you must also allocate time for the arrival as well
as the approach (circuit if VFR). You must learn to estimate this time reasonably accurately. A single VFR
Page 184
Navigation for Professional Pilots
circuit takes about 6 minutes. If you require a low pass and a second circuit before landing the time will
double, or more. So apply a suitable estimate for approach and landing time.
On VFR flights approach and landing time should be included in the time you file on your flight plan. We
will discuss this further later. On IFR flight plans you DO NOT include approach time in the filed time.
The ENL does not include approach time in the IFR enroute time but it does in the VFR time enroute.
VFR flights don’t legally require an alternate, and don’t generally need one. But, in some cases it might be
wise. For example if you are going to a remote strip where you intend to make a precautionary approach
and land (time for the precautionary would be in contingencies) then you will need an alternate in case
you determine that you cannot land.
Reserve
The last row of every nav-log is “Reserve.” There are legal requirements for reserve fuel. Normally this is
the value that should go on this line. Extra reserves that you wish to carry should be entered under
contingencies on the navlog.
Reserve is the amount of fuel that you plan to have left in your tanks when you land. Its purpose is NOT for
contingencies – those must be planned and allowed for separately. Reserve is really just for calculation and
operational errors. It is almost impossible to set the power to exactly the planned value, and no one ever
gets the mixture set 100% perfect, etc. Reserve simply gives you a margin for error. The law requires 30
minutes for day VFR and 45 minutes for night VFR and IFR flights. You are stuck with these values, but
realistically reserve should be more on a long flight, especially in a light airplane with inaccurate fuel
gauges.
An important point to think about for light aircraft operation is in initial loading of the airplane. You might
calculate that you should depart with 23 gallons of fuel, but how do you get exactly that amount in the
tanks. On a C-172P with standard tanks it would be just a bit more than ½ tanks, but just how much? You
can’t really trust the fuel gauges, so you do your best to dip the tanks but there is bound to be some error.
Most pilots try to fill the tanks to “at least” the intended amount, but it can be quite difficult. Consequently
the reserve you enter on your navlog has considerable error in it.
Take note on page 4-17 of the C-172P POH that you can get 4% greater range than the cruise performance
charts predict if you lean the mixture to peak EGT. At Selkirk College we don’t normally do that, but it is
worth knowing in case an emergency should arise. Here is something to think about: if an adjustment of
50°F in EGT makes a 4% difference in range and this corresponds to about 25rpm change how accurately
would you say you normally lean the mixture and what is your percent error?
Page 185
Navigation for Professional Pilots
Use the TAB-KEY to advance through the nav-log, that way you won’t miss anything.
Read the “balloons” that pop-up as you tab through the nav-log, these tell you how to fill it in.
Wind, temperature, and variation are automatically copied from one row to the next to save the time
required for entering these values on each row. However, should a value change you can enter a new value
any time and it will propagate throughout the remainder of the navlog.
After filling in reserve time the next TAB-STOP is for airport data at the lower left of the nav-log. Typing in
this data is much neater than filling it in by hand.
When the ENL is completely filled out hide all unused rows in order to avoid clutter – but be sure they
contain no data before hiding them.
Locate the departure and destination airports on your VNC. If you aren’t sure which VNC you need lookup
the airport in the CFS where the REF section tells you which VNC and WAC chart the airport is on, as well as
which LO chart if you are IFR.
Locate a suitable SHP, taking into account the factors discussed above.
If the flight is in the mountains, or there is restricted airspace near the destination locate a descent point
(DP.) Descent points are discussed in detail later under the topic of mountain cross countries.
If the trip is more than 300 NM choose some intermediate checkpoints so that no leg is longer than
300NM. This reduces convergence to an insignificant factor and allows us to plan each leg as a Rhumb
line. You may also find it practical to choose intermediate checkpoints in order to avoid directly over flying
restricted airspace, high terrain, etc.
Note that if you are planning a very long flight, say 1000NM or more, you will need a large scale planning
chart if you wish to establish a Great-circle route.
Once you have chosen your route draw straight track lines, starting at the SHP between each pair of
checkpoints with the last track line ending at the destination airport (or DP if applicable. See mountain
Page 186
Navigation for Professional Pilots
flying below for more information about DP.) When a track-line must cross from one side of a VNC or WAC
to the other use the procedure described in the next section to draw the line.
Once the track lines are drawn make 10NM reference marks along each line, as shown below.
Next, make 10° drift lines at each checkpoint, starting with the SHP. Note that if you have two SHP, as is
sometimes the case in mountain flying, the drift lines should start at the second SHP. Make drift lines for
each leg with the last set of closing drift lines at the destination airport or DP as the case may be.
Page 187
Navigation for Professional Pilots
VNC charts are printed on two sides. It is therefore often necessary to draw a straight line between
two points that are on opposite sides of the chart. In the figure below imagine that you want to fly
directly from point A, on the north side of the chart, to point B on the south side.
1. Layout a separate piece of paper over the north chart and mark point A. In addition mark TWO
points that are common to both the north and south side of the chart; these are points D and E.
2. Position the paper on the common points on the south side of the chart, as shown above.
3. Draw the straight line from point B to point A on the separate paper.
4. Mark a point C on the straight line on the south chart that is common to the north chart.
5. Draw the line from point C to point A on the north chart (not shown in the diagram.)
Page 188
Navigation for Professional Pilots
As you can see it only takes a few minutes to prepare the map for a VFR cross country. Once the map is
prepared you are ready to start filling in the navlog. You will of course need to measure the true track and
length of each leg.
Measure the length of each leg, using an ICAO ruler, and enter it on your navlog. Then measure the true
track by placing your protractor at the midpoint of each leg. (Remember the theory of convergence,
covered previously, where you learned that at the midpoint of each leg a Great-circle track and Rhumb line
are equal.)
You navlog should now have all the required information. Simply proceed as already covered to fill in the
rest of the data and you will be ready to go.
In this section I will comment on a few common errors or oversights in filling out flight plans. It is assumed
that you understand the basics as described in RAC 3.15 and 3.16
It is quite common when filling a VFR flight plan to include an intermediate stop. Normally this is not
permitted IFR, although it can be done if the IFR flight is in uncontrolled airspace. The rules regarding this
are in RAC 3.10. Two points that seem to be missed by many pilots are that the intermediate stop is
indicated in the route section of the flight plan in the form shown below. And the total duration of the
flight must include the intermediate stop. I have noticed that many pilots who lack experience in long trips
vastly underestimate the time required for an intermediate stop. A fuel stop can only be completed in ½ an
hour if everything is precisely arranged and organized. A more typical fuel stop takes 45 minutes to an
hour. So, allow sufficient time.
Pay particular attention to the rules for filing changes to altitude and true airspeed. This is covered in RAC
3.16.6. On many of the flight plans assigned in this course you will change cruise altitude and consequently
cruise speed. You are expected to know how to record this properly on the flight plan form.
A common mistake is to put arrows or similar symbols in the route section. This is NOT acceptable. Read
RAC 3.16.6 carefully and follow the prescribed format. Also, see the examples provided at the end of the
section. In the Canadian format no symbols or words are required between checkpoints when the route is
direct. If the route in an airway you should name the airway. It is as simple as that, so don’t make it
complicated by adding anything else.
Page 189
Navigation for Professional Pilots
Page 190
Navigation for Professional Pilots
Page 191
Chapter 9
Mountain Cross Country
There is an entire section in your FTM/IPM on mountain flying that you must read. In this text I will only
make some remarks about the considerations for laying out a navlog and filing a flight plan for a VFR
mountain cross-country.
By far the most important aspect of mountain flying is selecting an appropriate route and determining
that the weather is adequate for the flight. This is discussed in the FTM/IPM and not repeated here.
In the mountains distinctive, rivers, and valleys, peaks, roads, railways, etc. provide the ideal circumstance
for pilotage navigation. When the ceilings are low VFR pilots must fly in the valleys, if they are to fly at all,
and in such cases pilotage becomes the only viable form of navigation. Even when ceilings are high and DR
is used it is very easy to slip back and forth between DR and pilotage due to the numerous easy to identify
geographic features. Any experienced mountain pilot soon becomes a master of pilotage. But it is
important not to turn your back totally on DR. The ideal form of mountain navigation weaves pilotage and
DR into a seamless, almost effortless, procedure.
In the mountains you will often be below the tops of the mountains when you pass the SHP and as such
you may be unable to fly the calculated heading. What should we do?
Navigation for Professional Pilots
The first tip is pretty obvious. Try to pick an SHP such that the subsequent track follows a valley so that you
can climb on the pp-leg as planned. What if you can’t do that though?
Again the answer is pretty obvious. You will have to use pilotage until you clear the top of the mountains.
In this case we recommend that you plan a second SHP from which you can begin DR. It is always much
more accurate to begin DR from a specific SHP.
Sometimes pilots skip the procedure of selecting the second SHP, but this is usually because they are
overcommitted to pilotage. In other words, they are not going to do DR at all. I recommend this only for
relatively short trips on familiar routes. But, if the route is less familiar and you want to achieve efficient
navigation always have a specific SHP and use DR. This frequently means having two SHPs.
When the route directly to an airport crosses high terrain you should always check that a descent to the
airport will be possible. If it is not possible then on alternative is simply to circle down over the airport, and
time for this should be allocated, normally under approach and landing on the navlog. But, circling down
over the airport is seldom the most efficient way to handle the situation.
Take the example of an airplane arriving in Castlegar from Vancouver. The straight-line route runs over the
ridge just west of the airport and would leave the airplane at 7000’ or so within a mile of two of the
airport. Pilots almost naturally divert slightly off this straight-line route and descend along the Arrow Lake.
In short they plan the flight NOT to CYCG but to a DP at Deer Park.
In all mountain cross-countries be sure to examine the route and determine if you need a DP.
The creation of a navlog, as described so far, is based on the presumption of DR. When we open the flight
plan, as we have recommended for departure and arrival, we are really saying that pilotage will be used in
these phases of flight. Now we are saying that pilotage is to be used throughout the flight, so the navlog
must be very open.
On a valley crawl legs should be grouped (that’s what open means.) Heading obviously changes every few
minutes as the pilot follows a valley. Having a leg for every change in heading is totally unrealistic. Instead
Page 194
Navigation for Professional Pilots
the legs are chosen based only on major changes of direction and or between major checkpoints such as
large towns, lakes, etc. This is a very open format.
The track in this case requires a bit more consideration than usual. A single track from departure
direct to destination usually doesn’t provide enough reference, while a separate leg for each little twist
and turn is too cumbersome to plan and to execute. We need something in between. As a practical
example, a valley crawl from Castlegar to Grand Forks could be planned as three legs: One from the
Keenleyside dam to Renata, one south to Christina and one east to Grand Forks.
The usual method of measuring the length of a leg, by using a ruler, will not give an accurate distance. You
must learn to estimate the actual distance flown due to weaving around the snaking turns of the valley.
You should certainly start by measuring the straight-line distance from the beginning of the leg to the end,
with a ruler, but then you must add an estimated amount to allow for the turns of the valley.
There is NO SENSE calculating wind drift, drift angle, and heading for the leg. Indeed you can only estimate
the average track (because it changes continually as you fly.) Don’t worry about drift, your eyes will keep
you on track using pilotage. There is no need to put drift lines on the map.
Groundspeed must be estimated in order to calculate time and fuel for the flight. Based on your average
track and the wind you can estimate the average groundspeed. The hard part is often determining what
the wind will actually be. FD forecasts are of limited applicability. Reported ground winds and winds aloft
are obviously used to estimate wind at your chosen cruise altitude. Keep in mind that under the
circumstances of a valley crawl you often have to change cruise altitude frequently enroute. Wind
normally is funneled to follow the valley, so your main task is to guess whether there will be a headwind or
tailwind and how strong it will be; if in doubt always estimate low for tailwinds and high for headwinds. In
the wind column of the navlog write only the headwind or tailwind estimate – e.g. +10 or -5.
You will be given several assignments to plan valley cross-countries to develop the skills described above. It
is crucial that you learn to efficiently open your flight planning so that you can prepare the navlog in only a
few minutes, because by far the most important part of valley crawl planning has nothing to do with
making a navlog. The most important aspect of valley crawl planning is route analysis. You must examine
the route looking for difficult points, such as passes, and most important of all, looking for alternate
routes. In the discussion about diversions later in this text it is pointed out that a safe diversion in the
mountains is only possible if you have planned for it in advance. Given that diversions are very common
you must have every safe route option in your mind before you go on a flight. It is very common that the
shortest route for a mountain flight is not the one with the lowest terrain. There is nothing wrong with
planning the shorter route, but if you run into low ceilings and decide to divert to the longer lower route
you want to have figured out ahead of time that you have enough fuel for that. You must know that if you
don’t have enough fuel for a particular diversion option, where you will make fuel stops, etc. Don’t set out
on a mountain cross country in marginal weather without all the above thoughts and options sorted out in
your mind.
Page 195
Navigation for Professional Pilots
accurately maintains – the intended track. This makes it all too easy to lose track of time and over fly a
turning point. While it might be difficult to imagine a pilot missing the turn at Christina (for Grand Forks)
and picking up the road to Republic, some 20 miles south, it is not impossible and it is really easy, when
following Highway 3 west from Cranbrook, to miss the turn at Yahk and continue on Highway 95, going
south-east down to Copeland. This is not a complete disaster but in marginal VFR conditions it is very
disconcerting and re-orientation can take several minutes.
There is little need to recalculate headings, since that information is only approximate to start with. It is
important, however, to update the ground speed information – again, in order to monitor the progress
along the track. If the leg is long enough to warrant a couple of 10-mile marks then these can be used just
as they are on a regular navigation leg. More often however, the legs are barely long enough to justify one
10-mile mark so it is more appropriate to wait until reaching the next turning point, where the pilot can
either compare the ETE to the actual time enroute (ATE) in order to derive a time differential or simply
divide the distance by the ATE for a ground speed. In either case, it is important to remember that a
headwind component on one leg can easily become a tailwind component on the next leg: With winds
aloft out of the north, a tailwind on a leg headed south east could well become a head wind if the valley
makes a turn around to the north east. Situational awareness is always critical while valley crawling.
Page 196
Navigation for Professional Pilots
Page 197
Chapter 10
Time Saving Flight Planning Techniques
In all that we have done so far we have planned flights by breaking flights into climb, cruise and descent
legs. We have simplified our task by opening the flight plans, and this is an important time saving
procedure. There are some other commonly used “short cuts” to flight planning that I would like you to be
aware of.
Hour one covers 180NM. Subsequent 420NM require 1.9 hours (420/220.) Total trip time is therefore 2.9
hours, which will cost $5800.
If the customer says, “yes” to your quote you quickly file the flight plan for 3.9 hours and have 1070 lb of
fuel, plus contingencies and reserve loaded. The fuel is calculated as 500 + 1.9 x 300.
Block flight planning is only safe when the airplane always flies at essentially the same cruise altitude and
wind is not a factor. This is clearly a dangerous assumption, so block planning must be used with great
consideration.
An important point I must make before explaining how this is done is that it doesn’t work. In other words,
climb penalty planning is a myth. Still, it is so commonly used that you need to know the concept if for no
other reason than so you can see its limitations. (Actually, we will conclude that penalties work in the right
circumstance.)
Climb penalty planning starts by saying, “wouldn’t it be easy to flight plan if the departure airport was on
a mountain exactly at the cruise altitude for the trip. This imaginary situation is shown in the picture
below:
Navigation for Professional Pilots
If the above situation actually existed there would be no need to plan a climb leg. The airplane would
already be at cruise at the moment of liftoff. The next step in climb penalty planning is to ask what the
difference in time and fuel for the trip would be in the following situation:
Obviously the airplane in this situation must climb from the departure runway to the cruise altitude. Taking
a C-172P as an example, it will climb at 85KIAS (TAS is higher) and then cruise at about 105KTAS (the exact
value depends on the cruise altitude.) This airplane will “fall behind” the other airplane at about 15 knots.
Obviously the trip will take longer this way. Similarly it will use more fuel, due to the higher rate of fuel
flow in the climb, and the slightly longer flight time.
Page 200
Navigation for Professional Pilots
The idea behind climb penalty planning is simply to determine the difference between the above cases and
then add that onto case I as a penalty. We can do this quite easily using the ENL.
First examine the third leg of the above navlog. It shows a cruise leg of 100NM. The airplane is level for
this entire leg, so it corresponds to the part I diagram above. The leg requires 55 minutes and consumes
6.6 gallons.
Next examine the first two legs of the above navlog. Together they also cover a distance of 100 NM, but
the airplane climbs from sea level to the cruise altitude of 6000 feet. This takes 58 minutes and 7.9 gallons
are consumed. This corresponds to the part II diagram above.
The time penalty is obviously 3 minutes per 6000 feet, i.e. 30 seconds per thousand feet. The fuel penalty is
1.3 gallons per 6000 feet, which is a bit less than ¼ gallon per thousand feet.
To use the penalties for a C-172P simply plan the trip as though the entire flight was in cruise, i.e. as
though the part I diagram applies. Once you have done this add a penalty of 30 seconds and .25 gallons
for each thousand feet the cruise altitude is above the takeoff altitude.
Repeat the above ENL analysis for the B95 and determine the climb penalties for that airplane.
At the beginning of this section I said that the real problem with climb penalties is that they don’t work.
Can you spot the flaw in the logic behind this procedure? Think about it before reading the next
paragraph.
In our earlier cruise altitude analysis we learned that depending on the length of a trip there not only is no
penalty for climbing, there is a penalty for not climbing. Take the airplane on the 500NM cross country on
page Error! Bookmark not defined. a pilot planning this flight for cruise at 9500’ and then adding a
penalty would be completely mislead.
Climb penalties are only applicable to flights at relatively low altitudes and over relatively short distances.
In this case they do reflect the penalty due to climbing that we already discovered on page Error!
Bookmark not defined..
Page 201
Navigation for Professional Pilots
Page 202
Chapter 11
Enroute Navigation Skills
This section covers several navigation skills that you will need to develop and apply in flight. The primary
emphasis in this course is on preflight planning, most of the in-flight skills are developed in Avia 100 and
200, but there are some things you should keep in mind.
Map Reading
Its pretty obvious that a fundamental skill in navigating VFR is the ability to interpret a VNC chart and
locate the corresponding geographic features on the ground.
The first principle of map reading is work from map to ground, NOT the other way around. In other words
you locate a geographic feature on the map and then look out the window until you spot the same feature
on the ground. You do NOT spend time with your eyes down on the map trying to find some feature, such
as a small lake or road that you have spotted out the window. The latter procedure results in too much
time with eyes in the cockpit. Good airmanship is to have your eyes out the window 99% of the time.
You must learn which features will be distinctive “out the window” and which won’t. on the map certain
things such as VORs, NDBs, towers, runways, small town, and power lines are quite distinctive, but out the
window they are nearly impossible to see. There are exceptions of course. For example power lines over
mountain ridges can be quite easy to see because a wide swath of trees is cut down along the line. And
radio towers are very easy to see at night. The specifics of night cross countries are discussed in your
FTM/IPM and are covered in Avia 201; they will not be covered further here.
The best procedure is to choose four or five geographic points on your map and then look out the window
until you spot them. These could be a town, a river, a road, and a mountain or valley. Once you have this
“list” of items gleaned from the map you scan the ground until you locate the corresponding locations.
There are of course lots of towns, rivers, roads and mountains in the world so how do you tell one from
another? The key here is to analyze the map and develop a mental image of the distinctive characteristics
of the ones you are looking for. For example does the town have a river running though it? How many
roads run in and out? And is there a nearby mountain? Try to have at least three distinctive features that
will distinguish the location you are looking for from others. These features can be anything, as described
above, as well as relative position, size, etc.
A common mistake is to choose geographic points that are too close to the airplane. In flight you can see a
long way and you should take advantage of that. It is much easier to locate a geographic point that is 5 or
10 miles ahead rather than one directly below you (the airplane doesn’t have a glass floor.) You can often
see large geographic features, such as distinctive mountains, lakes and rivers, 30 or more miles away.
Doing so reduces a lot of navigation effort, so it is highly recommended.
Navigation for Professional Pilots
Another frequent mistake is becoming too obsessive about spotting a particular geographic point. For
example you may be looking for a small town but not seeing it. Some pilots will keep looking and looking
and looking for this town until they are completely lost. This is due to a lack of time awareness, discussed
next.
Time Awareness
When you choose a geographic point on your map that you will be looking for a critical thing to do is
estimate roughly how long it will take until you reach the point. To do this simply be aware of how many
miles per minute (roughly) you are covering. Most airplanes cover at least 2 miles per minute, and many
go much faster than that. Therefore a geographic point 6 miles ahead will be beneath you in 3 minutes. If
you haven’t spotted it by then you’ve missed it. It isn’t critical to identify every point, so don’t worry about
it.
In light of the above, it is important to always be looking for more than one geographic point. Usually
three is a good number. If you miss one it won’t really matter. Also, finding one often makes it easier to
spot the others. Most importantly, be aware of time passing. If logic says you are past a checkpoint then
forget it, choose another one and look for that. Failure to follow this advice is what will get you lost.
Reorienting if Lost
The first question you must ask is; am I really lost? As a new pilot you may feel lost if you miss one
checkpoint, but you really aren’t. This was mentioned above.
Don’t panic. As long as you fly a straight-line you can always find your way back by simply “doing a 180.”
But it is important that you fly the specific heading on your navlog. The best way to get lost is to wander
around on random headings that are not recorded. As long as you are flying one heading (as opposed to
wandering) you can do a 180 and go back.
Of course if you have a working GPS you can read the latitude and longitude and immediately locate
yourself on the VNC. So, we will assume you don’t have such equipment.
If you are truly “lost” stay calm and keep your wits about you (which means you mustn’t panic.) When you
think about it you really aren’t “totally lost.” You can state your location in a hierarchy such as that you are
in Canada, B.C., Southern B.C. east of Vancouver, and so on. You probably know where you are within a
few miles tolerance. You could draw a circle on the map and say, “I am somewhere in here.” From this
known area of probability there are several things you can do:
If you have been flying a steady heading you can simply reverse it and go back to where you came from.
Remember to write down the time you turn around so you can estimate how long it will take to get back to
the starting point. Your previously recorded departure time will give you all the information you need.
Lucky you always record these things, right?
If the weather is suitable, climb to a higher altitude so you can see farther. If you can climb high enough to
get ATC on the radio you will be able to get radar or DF assistance from them. Radar is available in most of
southern Canada, but if you happen to be lost in the far north there is also the defense radar system. The
procedure for using this in the event of an emergency is covered in section F of your CFS.
Page 204
Navigation for Professional Pilots
If you have been wandering around, which got you lost, consider using the navigation technique called
landfall, which is described below. It is almost always possible to use a landfall to reorient yourself. If your
desired destination is not on an extended geographic feature suitable for landfall then pick an interim
destination from which you will be able to continue on.
In the prairies most small towns have the town name written on their grain elevator. If you fly any
direction you will come across a road within a short time. Follow it to a town and as you fly by you can
read the name on the elevator to identify your location.
Keep track of your fuel. If you brought lots of reserve you will be fine, but if fuel gets low and you are still
lost you may have to do a precautionary approach. Much more likely however is that you will reorient
yourself and be able to continue your flight. But be sure to recalculate your reserves. If they have shrunk
too low divert to another location and refuel. Most fuel starvation incidents follow getting lost.
Navlog keeping
On your navlog you must record the takeoff time and time past each checkpoint enroute. You should also
record ETA revised ETA for each checkpoint. These are standard procedures applicable to any log keeping
exercise. In addition your company may require many other pieces of information be recorded.
On the Selkirk College navlog we write the takeoff time in the designated location just before takeoff. Once
clear of the departure airport we then write down the ETA and Fuel Expiry time in the designated
locations. We then fill out the ETA column so that we have the ETA for each checkpoint. The final
checkpoint ETA should match the previously calculated destination ETA. If it does not then an adding
mistake has been made, which you must locate and correct.
Selkirk College navlog keeping involves writing down the time we pass each checkpoint enroute in the ATA
column. The ATA should be quite close to the ETA previously filled in. At a glance you will be able to see
that you are ahead of or behind schedule.
If the groundspeed is revised pencil the corrected value over the value on the navlog, then enter a revised
ETA in the designated column.
TIP: it is really quite rare for the winds aloft forecast to be wrong by more than 5 knots. This amounts to
saying that you normally will have a groundspeed within 5 knots of the planned value. If your calculated
groundspeed is substantially different than the flight planned value you should recheck your calculations
before jumping to any conclusions. When the wind is substantially different than the forecast there is
usually evidence such as turbulence or un-forecast storm activity.
TIP: when doing a groundspeed check your calculations are subject to round-off error. For example, you
measure a distance of 11NM and then measure a time of 4 minutes. Based on this your CR tells you that
the groundspeed is ____ Kts. Ask yourself what tolerance you would apply to this value. Consider this
before reading the next paragraph.
The groundspeed according to your CR is 165 kts. But the distance is rounded off to the nearest nautical
mile and the time is rounded off to the nearest minute. This amounts to saying that the actual distance is
Page 205
Navigation for Professional Pilots
between 10.4 and 11.4 and the time is between 3:31 and 4:29. Using these values your groundspeed could
be anywhere between 149 and 196 kts! (Check these values for yourself with a CR.) That is a very large
spread of “correct” values. If your navlog predicted a groundspeed of 150 knots should you revise your ETA
or not? The answer is that you don’t have an accurate enough groundspeed to decide.
To make an accurate groundspeed check you need more accurate data. The best you can usually do is
measure distance plus or minus ½ nautical mile Even after you do this you will find it difficult specify the
precise moment you pass the checkpoint, which adds another error bringing distance tolerance to at least
1 NM. You can use a stopwatch to get a more accurate time value, but it is still difficult to achieve an
accuracy right down to the second (see previous point.) Consequently, if you want a groundspeed check
accurate to the nearest knot you would have to fly a groundspeed check of at least one hour (60 minutes.)
Put another way, a six minute groundspeed check is at best accurate to plus or minus 10 knots. And a 3
minute groundspeed check is accurate plus or minus 20 knots, which is to say just about useless. So, make
sure you use fairly long groundspeed checks (10 to 15 minutes minimum), and know the tolerance of their
accuracy (4 or 5 knots at best.) If the obtained value lies within the tolerance of your flight planned speed
it is usually wise to take this as confirmation of the navlog and make no revision to your ETA.
Top of Descent
At some point you must start a descent from your cruise altitude so that when you reach the destination
airport you are at the desired altitude. This is the top of descent point (TOD.) Choosing it wisely is
important.
A lot of VFR pilots are in the habit of descending quite early. If you are approaching a major airport with a
lot of traffic, and in an area with lots of good forced approach sites, it might be wise to descend to circuit
altitude 10 miles before the airport (I am thinking about single engine airplanes here.) But in more rugged
terrain you want to reach circuit altitude only one or two miles prior to joining the circuit, in order to keep
as many safety options open as possible.
On the other hand, you don’t want to descend too late, if you reach the airport well above circuit altitude
you will have to circle down (which wastes time and fuel) or will dive (which is uncomfortable for
passengers and you.)
Most pilots plan descents based on a certain gradient. Three miles per thousand feet is the most common.
If you are flying a turbo-charged piston airplane it might be better to use four miles per thousand feet.
Simply calculate how may thousand feet you need to descend and multiply by three (or four) then start
your descent that number of miles from the location you which to reach circuit altitude.
Diversions
A diversion means changing your route and or destination while in flight. Diversions are very very common
occurrences in both IFR and VFR flight.
IFR flights routinely divert around areas of bad weather. The specific techniques for this however will be
deferred to Avia 260
Page 206
Navigation for Professional Pilots
VFR flights also often divert around areas of bad weather. It is not always necessary to change destination
when bad weather is encountered, frequently you can skirt the area of poor weather and re-intercept the
route beyond the area affected. But you must keep track of time so that you don’t run low on fuel. When
diverting around weather you are by definition using your contingency fuel, so as long as your navlog
shows that you have lots of contingency fuel you are fine. But if you have not allowed contingency fuel
then you will have to change your destination in order to refuel.
Transport Canada has established a specific diversion exercise that you must demonstrate on the
commercial pilot flight test. It is important to realize that this is only an exercise. It actually bears almost
no resemblance to 99% of real life diversion scenarios. On the flight test exercise you are required to draw
a free-hand line to a designated destination then estimate the heading and distance without using a
protractor or a ruler. You must then calculate (estimate) the time enroute in your head without a flight
computer. This is a great exercise in mental approximation but it is important for you to realize that if you
are actually doing a diversion there is nothing wrong with using a ruler, or a calculator.
To meet the Transport Canada diversion challenge most pilots estimate the distance by using the minute
marks on the VNC’s lines of longitude as a scale. Your instructor will show you how to do this if you haven’t
done it before. In the real world, just use a ruler if you have one. To estimate the track to the destination
you can just “eye-ball-it” or use a VOR rose to help you be a bit more accurate. You will be surprised how
closely you can eye-ball-it with a bit of practice. This is however a skill that requires practice. The best
thing to do is estimate all tracks before putting a protractor on them.
To estimate the time enroute if you don’t have a CR computer there are numerous mathematical tricks.
These are laid out on the ProfessionalPilot.ca website in the miscellaneous section. Anyone can do it, it just
takes a bit of practice, and it is well worth the effort.
When diverting in the mountains, on a valley crawl, usually means taking a totally different route. The
secret to success is in knowing all the routing options before you takeoff. Scanning the map looking for an
alternate route once you have run into poor weather is a recipe for disaster. I am sure than many of the
pilots who have killed themselves in the mountains (and there are a lot of them) did so when they had to
divert but were unprepared to do so. If you run into bad weather in the mountains and have to divert then
there should only be two possibilities. You either divert to an alternate route that you have previously
analyzed and planned, or you do a 180 back to the last suitable airport and land there until you get
organized to go on. NEVER plan a substantial diversion in-flight in the mountains.
The contents of a VFR position report are listed on the back cover of your CFS.
Ideally position reports should be made about every half hour on a cross country. In the mountains there
are often limited opportunities to make position reports, especially on valley crawl trips. In such cases the
Page 207
Navigation for Professional Pilots
best advice is to make every position report that you can. This sometimes means making two reports only
10 minutes apart and then other times an hour or more might pass due to lack of ground stations.
It is vital to realize that when you make a position report the information is recorded, for use if you don’t
arrive at your destination, but it DOES NOT update your flight plan. Many pilots misunderstand this fact.
For example, if you are falling behind schedule and will arrive 45 minutes late, if you file a position report
in which you give an ETA for your destination that correctly predicts your new arrival time FSS will still
initiate a search for you at the original ETA based on your flight plan. To prevent this you must specifically
request that your flight plan be amended to your revised ETA.
Imagine you wish to sail a ship across the ocean from France to Montreal. The ocean currents present the
same problem for ship navigation that wind does for pilots. In modern times you would use GPS or Loran-C
th
to navigate accurately in a straight-line between the ports. But imagine it is the 16 century and no such
system exists.
If you sail west from France you are most definitely going to hit North America. When you do sailors say
they have “made landfall.” But you are probably going to drift so if you aimed directly at the Saint
Lawrence there is no way to know if you are north or south of it.
The strategy used is to deliberately aim to one side or the other of the intended destination so that when
you do make landfall you know for sure which side of the desired point you are on and can follow the coast
to your destination.
The same technique can be used by pilots. For example if you are in Kelowna and fly east you really cannot
miss the Arrow Lake. Once you find the lake you can follow it to Castlegar. The first step is a rough DR (just
accurate enough to guarantee you don’t miss the target (Arrow Lake)) the second leg is pilotage (follow
Arrow Lake to Castlegar.)
Laying a landfall only works if the destination is on an extended geographically distinct feature that you
can lay landfall for and be certain you won’t miss. The Arrow Lake meets that criterion. Many airports in
the Prairies are along major highways, which can be used the same way, other towns are on railway
tracks, and so on. If you are going to lay landfall simply estimate a heading that will put you one-way-or-
the-other from your intended destination. Once you make landfall use pilotage to find the destination. This
technique is often practical on a diversion around poor weather or for reorienting yourself if you get
“slightly” lost.
Page 208
Navigation for Professional Pilots
Page 209
Chapter 12
Oceanic Flight
The full details of oceanic flight are beyond the scope of this course. You will learn more about them in
second year. However, two points of navigation, which are usually considered important for oceanic flight,
will be covered here. These are the point of no return (PNR) and critical point (CP.)
Each of these concepts can be applied to any flight, even a short over land flight in a C-172; but they really
don’t make a lot of sense in that context. Still, the mechanics of doing the calculation is the same no
matter what type of airplane you fly.
On many of the short flights you have made in C-172 and similar airplanes in your flying career you
probably carried enough fuel to fly all the way to destination and then return to departure point. In such a
case you never reached a point of no return (PNR.) PNR is simply what the name says, the point beyond
which you do not have enough fuel to return to the departure aerodrome.
Endurance Eu
We will represent endurance with a capital E. E is the amount of time in hours that the airplane can fly. Et
is the total endurance to dry tanks. For example a C-172 with standard tanks has 38.9 gallons at takeoff
and an endurance of 5:18. It would be very unwise to calculate PNR based on this number however
because that would imply proposing to return and land just as fuel runs out – a very scary idea. Eu will
represent the useable endurance, which must include at least reserve fuel, and possibly some contingency
fuel. For the C-172 with standard tanks we could set the value of Eu at 4:40 for example.
If there was no wind the airplane would reach PNR by flying out to half its endurance, or in other word PNR
would equal total range divided by two.
We also define engine-out-PNR in which we assume all engines operating prior to the 180° turn and one
engine out after the turnaround. I.E. GS home-SE will be based on the engine out performance, but GS out is
always based on all engines operating normally.
PNR Formula
In zero wind PNR is determined very easily by calculating total range (E x GS) and dividing by two:
It is always a good idea to do the above calculation as a first estimate; then use the formula below to
account for wind. The result is always a distance LESS than the zero wind distance above. I.E. wind always
reduced PNR.
For example an airplane with a zero wind GS of 100 Kts and an endurance of 4 hours has a PNR of 4 x 100 /
2 = 200.
Page 212
Navigation for Professional Pilots
If the airplane in the previous example experiences a 20Kt tailwind outbound the PNR will be 4.5 x 120 x 80
/ (120+80) = 216Nm. As expected, this is slightly less than the zero wind DPNR.
Important: PNR with wind is always less than PNR with no wind.
Note that PNR questions will be on the ATPL and IATRA written exams
IMPORTANT: if a question asks for engine-out-PNR calculate GSout with all engines operating normally and
GShome with one engine inoperative.
Note that you can always apply the DPNR formula to any flight but in many cases the PNR is beyond the
destination. I.E. the airplane can turn around at any point on the flight and return to departure point. This
is good to know; therefore PNR should be routinely calculated and if it is beyond destination – great.
Here is the “proof” of the formula. It is not necessary for you to memorize the proof but you should know
the first line, i.e. the definition, and the last line. By using only the first line you can find the correct answer
from among a selection on a multiple choice exam.
Page 213
Navigation for Professional Pilots
It should be obvious that in zero wind the CP is exactly at the mid-point of the flight. In other words on a
1000 NM flight CP is 500 NM. But CP will move into the wind. I.E. if there is a tailwind you will reach CP
before the mid-point or if there is a headwind you will reach CP after the midpoint – see if you can visualize
why this is so.
CP can be calculated for all engines operating normally and also for engine-inoperative. In the later case
the CP represents the, on one engine, to return to base or continue to destination
IMPORTANT: when calculating CP always use the speed as it will be after the CP. Thus, if you are asked for
the single-engine CP use single engine speeds, if asked for all engines CP use all engine speeds – NEVER mix
speeds in a CP calculation (this is different than a PNR calculation.)
Page 214
Navigation for Professional Pilots
Let’s calculate where CP is with a 20 Knot tailwind outbound. GSon is 120 KT and GSreturn 80KT. Therefore CP
= 400 x 80 / (120 + 80) = 160. So, with a tailwind CP comes before the halfway point.
Let’s calculate where CP is with a 20 Knot headwind outbound. GS on is 80 KT and GSreturn is 120KT.
Therefore CP = 400 x 120 / (120 + 80) = 240. So, with a headwind CP move to beyond halfway point.
Page 215
Page 216
Appendix 1– C-172 Interpolation Tables
Power setting ___________ feet
RPM TAS
___________ temp
_______%
65%
______%
_______%
65%
______%
_______%
65%
______%
_______%
65%
______%
________ feet
Page 217
________ feet
________ feet
Page 218
Appendix 2 - Inbound PDT Practice Sheet
In the sheet below fill in the heading you must turn to, or if it is an over-60 write down PT (for
procedure turn.)
150 100
300 280
240 290
040 120
135 165
In the table below fill in a random selection of bearings to beacon in the first column:
Page 219
Next fill in desired bearings considering the first column and making the bearing within 60 most of the
time.
Page 220
Appendix 3 - Outbound PDT Practice Sheet
In the sheet below fill in the heading you must turn to. There is no “over 60” limit for outbound PDTs.
210 250
340 240
005 320
140 180
280 270
In the table below fill in a random selection of bearings from beacon in the first column:
Page 221
Next fill in desired bearings in the second column. There is no 60 degree limit, but normally the desired
should be within 180 (to make sense.)
Page 222
Appendix 4 – Definitions
Deviation: The difference between actual magnetic heading and the compass indications. This error is
shown on a compass correction card.
Variation: The difference between magnetic track and true track. This due to the magnetic north pole
NOT being at the actual north pole. Variation is shown on both IFR and VFR charts as lines of equal
variation, known as isogonic lines.
Convergence: Meridians of longitude converge at the north and south poles, as such they are not quite
parallel to each other. The angle at which they converge is known as convergence. Convergence is
zero at the equator and increases the closer to the pole you fly. An aircraft flying along a Great Circle
route much change heading to compensate for convergence.
Great Circle: A line on the surface of the earth that when extended completely encircles the earth and
has its center coincident with the earths center. Such a line is the shortest distance along the surface
of the earth between any two points on the line.
Rhumb Line: A line on the surface of the earth between two points such that the true track along the
line is constant. A Rhumb Line is only coincident with a great circle if it is also a Meridian, or the
equator. All other Rhumb lines vary from the Great Circle (see above definition.) Rhumb Lines are
popular with pilots because you can fly a constant heading rather than changing headins as you
would on a Great Circle.
Page 223