Professional Documents
Culture Documents
Part #1003-0710-10
Quantity Description Part No.
1 Rear Tag Surround 1003-0711-10
1 Powder Coated Black Filler Plate 1003-0713-10
1 Fine Mesh Section 1003-0712-10
1 Hardware Kit (components listed below): 1003-0715-10
(6) #6 x 1/2” Torx Pin Head Screws 1999-0109-00 2
(1) Torx T-10 Tool 1999-0107-00
(40”) 3M Scotchcal Protective Tape 1999-0270-00
3
(3”) .045” x 1” Double Faced Tape 3004-9244-92
2
“Black Ice” Part #1003-B710-10
Quantity Description Part No. 2
1 Rear Tag Surround 1003-0711-10
1 Powder Coated Black Filler Plate 1003-0713-10 1. Make sure the vehicle is clean before you begin the instal- 3. Carefully remove the surround, do not let it scratch the
1 “Black Ice” Fine Mesh Section 1003-0712-10BI lation. Remove the existng rear tag or frame (if installed). painted surface. Use masking tape to tape up to the edge
1 Hardware Kit (components listed below): 1003-0715-10 2. Align the chrome plated surround into place, making sure of the grease pencil marks made in the previous step.
(6) #6 x 1/2” Torx Pin Head Screws 1999-0109-00 the top edge is flush and tight against the factory chrome
moulding. Use a grease pencil to outline the surround.
(1) Torx T-10 Tool 1999-0107-00
(40”) 3M Scotchcal Protective Tape 1999-0270-00
(3”) .045” x 1” Double Faced Tape 3004-9244-92
5 7 6
9 11
9. Once the frame is removed, use a 3/32” drill bit to drill 10. Cut the supplied piece of 1” double faced tape into three 11. Install the powder coated plate by peeling off the double
through the mounting tab marks and into the factory equal sections and install them onto the back of the faced tape backing, align the part tightly against the top
chrome moulding (two holes per side). Drill through the powder coated rear tag filler. Be sure to install the tape of the tag recess and press firmly into place.
marks made in the trunk lid where the lower mounting on the back of the part (the side where the part number
tabs will attach to the trunk lid. label is applied). Make sure you place the tape at the top
edge of the tag filler.
13
12
12. Align the chrome plated mesh section over the powder 13. Reinstall the T-10 Torx pin head screws to secure the sur- 14. If the mesh section is slightly loose, the rear tag assembly
coated filler and use masking tape to keep the mesh prop- round to the trunk lid. DO NOT OVERTIGHTEN OR YOU will hold it firmly in place once it is installed.
erly aligned with the fille. WILL STRIP OUT THE MOUNTING HOLES! Make sure the
mesh is not caught behind the lower mounting tabs.
WARRANTY INFORMATION:
E&G Classics, Inc. warrants its chrome parts and products to be free from defects in
material, workmanship or finish for Forty-Eight (48) months from the date of shipment
by E&G. This warranty is limited to the repair or replacement, at E&G Classics option,
of the defective part or product.
1.) Present your E&G unit to an authorized distributor in your area with proof of
purchase.
2.) If no distributor is available, contact E&G Classics (address below) for author-
ization to return unit.
3.) Returns - All unauthorized returns will be refused. Merchandise approved by E&G for
return must have been purchased within the Forty-Eight (48) months. All returns re-
quire an authorization number obtained from E&G and the actual return must be ac-
companied by the written authorization form filled out completely. All merchandise
must be inspected upon receipt and shortages reported within 48 hours. All merchan
dise must be in a resalable condition. Merchandise must be packed carefully in the orig-
inal packing. If original packing is no longer usable, repack item(s) comparable to orig-
inal manner. All returns are subject to a 25% handling charge. Special order items are
not returnable. Defective merchandise must have an explanation of the problem. No
credit will be issued unless invoice number and date of purchase has been supplied.
Manufacturer shall be sole judge of defects in a product.
4.) UPS accounts - All returns must be prepaid. Do not send return shipments
freight collect. Once E&G has made its decision and it is a claim against our
warranty policy, E&G will credit incoming freight on damaged parts.
5.) No discontinued part or parts changed due to body style are returnable.