Professional Documents
Culture Documents
Assessment System
Time Remaining:
A port can act as the destination port for all SPAN sessions configured on the switch.
A port can be configured to act as a source and destination port for a single SPAN session.
Both Layer 2 and Layer 3 switched ports can be configured as source or destination ports for a single SPAN session.
Port channel interfaces (EtherChannel) can be configured as source and destination ports for a single SPAN session.
Refer to the exhibit. Which statement is true about the local SPAN configuration on switch SW1?
The SPAN session transmits to a device on port Fa3/21 a copy of all traffic that is monitored on port Fa3/1.
The SPAN session transmits to a device on port Fa3/21 a copy of all traffic that is monitored on port Fa3/1, but only if port Fa3/1 is
configured in VLAN 10.
The SPAN session transmits to a device on port Fa3/21 a copy of all traffic that is monitored on port Fa3/1, but only if port Fa3/1 is
configured as trunk.
The SPAN session transmits to a device on port Fa3/21 only a copy of unicast traffic that is monitored on port Fa3/1. All multicast
and BPDU frames will be excluded from the monitoring process.
3
Refer to the exhibit. Which statement is true about the VSPAN configuration on switch SW1?
The VSPAN session that is configured on port Fa3/4 can monitor only the ingress traffic for any of the VLANs.
The VSPAN session that is configured on port Fa3/4 can monitor only the egress traffic for any of the VLANs.
Port Fa3/4 must be associated with VLAN 10 or VLAN 20 in order to monitor the traffic for any of the VLANs.
The VSPAN session transmits a copy of the ingress traffic for VLAN 10 and the egress traffic for VLAN 20 out interface Fa3/4.
The capture port captures all packets that are received on the port.
The capture port needs to be in the spanning-tree forwarding state for the VLAN.
5 All access ports on a switch are configured with the administrative mode of dynamic auto. An attacker, connected to one of the ports,
sends a malicious DTP frame. What is the intent of the attacker?
VLAN hopping
Refer to the exhibit. A network engineer is securing a network against DHCP spoofing attacks. On all switches, the engineer applied
the ip dhcp snooping command and enabled DHCP snooping on all VLANs with the ip dhcp snooping vlan command. What
additional step should be taken to configure the security required on the network?
Issue the ip dhcp snooping trust command on all uplink interfaces on SW1, SW2 and SW3.
Issue the ip dhcp snooping trust command on all interfaces on SW2 and SW3.
Issue the ip dhcp snooping trust command on all interfaces on SW1, SW2, and SW3.
Issue the ip dhcp snooping trust command on all interfaces on SW1, SW2, and SW3 except interface Fa0/1 on SW1.
7 Which countermeasure can be implemented to determine the validity of an ARP packet, based on the valid MAC-address-to-IP address
bindings stored in a DHCP snooping database?
DHCP spoofing
MAC snooping
8 How should unused ports on a switch be configured in order to prevent VLAN hopping attacks?
Configure them as access ports and associate them with an unused VLAN.
9
Refer to the exhibit. Given the configuration on the ALSwitch, what is the end result?
forces all hosts that are attached to a port to authenticate before being allowed access to the network
disables 802.1x port-based authentication and causes the port to allow normal traffic without authenticating the client
10
Refer to the exhibit. Network policy dictates that security functions should be administered using AAA. Which configuration would create
a default login authentication list that uses RADIUS as the first authentication method, the enable password as the second method, and
the local database as the final method?
11
Refer to the exhibit. A switch is being configured to support AAA authentication on the console connection. Given the information in the
exhibit, which three statements are correct? (Choose three.)
The configuration creates an authentication list that uses a named access list called group as the first authentication method, a
TACACS+ server as the second method, the local username database as the third method, the enable password as the fourth
method, and none as the last method.
The configuration creates an authentication list that uses a TACACS+ server as the first authentication method, the local username
database as the second method, the enable password as the third method, and none as the last method.
The none keyword enables any user logging in to successfully authenticate if all other methods return an error.
The none keyword specifies that a user cannot log in if all other methods have failed.
Place all unused ports into a common VLAN (not VLAN 1).
Configure MAC address VLAN access maps.
14 What are two purposes for an attacker launching a MAC table flood? (Choose two.)
15
Refer to the exhibit. After the configuration has been applied to ACSw22, frames that are bound for the node on port FastEthernet 0/1
are periodically being dropped. What should be done to correct the issue?
Add the switchport port-security mac-address sticky command to the interface configuration.
Change the port speed to speed auto with the interface configuration mode.
16
Refer to the exhibit. What is the state of the monitoring session?
17
What is the function of the 6500 Network Analysis Module?
gathers multilayer information from data flows that pass through the switch
18 What technology can be used to help mitigate MAC address flooding attacks?
root guard
Private VLANs
DHCP snooping
19
What advantage for monitoring traffic flows does using VACLs with the capture option offer over using SPAN?
VLAN ACLs can be used to capture traffic to the CPU separate from the traffic that is hardware switched.
20 What Cisco tool can be used to monitor events happening in the switch?