Professional Documents
Culture Documents
SEMICONDUCTOR COMPANY
MATSUSHITA ELECTRIC INDUSTRIAL CO., LTD.
Contents
Overview …....................................................…………………………………………………………………….. 3
Features ………………………………….………………………………………………………………………….. 3
Applications ……………………………….………………………………………………………………………….. 3
Block Diagram ……………...…………….………………………………………………………………………….. 4
Pin Descriptions …………………………..................................………………………………………………….. 5
Absolute Maximum Ratings ……………………………………………………………………………………….. 7
Operating Supply Voltage Range ………………………………………………………………………………….. 7
Electrical Characteristics ……………………………………….………………………………………………….. 8
Control Terminal, The Mode Table ……………………………………………………………………………….. 11
Technical Data ……………………………….……………....…………………………………………………….. 12
y Circuit diagrams of the input/output part and pin function descriptions .....................................…………… 12
y Control sequence at power on/off ………......…………………….……………………………………………… 19
y Power dissipation of package HSOP056-P-0300A ….................................…….........……………………… 20
y Usage notes ………………………………………........................................................……………………….. 20
y Main characteristics ….…………………….................…………………………………….........……………….. 21
SDC00057AEB 2
AN12943A
AN12943A
Audio signal processing IC for notebook PC
Overview Unit: mm
AN12943A is an one-chip IC for the stereo speakers which can output
1 W by 8 Ω, headphone amplifiers, line amplifiers and electronic
volumes.
Since the headphone amplifier is a dual power supply system which
uses a DC-DC converter to create the negative power source, an output
capacitor is not necessary.
Also the AN12943A is built-in power saving on/off function to
Features
y Speaker amplifier
1 W × 2-channel: 8 Ω, VCC = 5 V
y Headphone amplifier
Dual power supply system doesn't require output capacitor.
y Built-in automatic power saving function.
It detects input signals and switches on/off (with the on/off switch for
HSOP056-P-0300A
the auto power saving).
y Built-in electronic volume and line amplifier
Applications
y Notebook PC
SDC00057AEB 3
AN12943A
Block Diagram
−9.17 dBV −10 dBV
OUT-L-ch. (Line) 4.7 µF 10 V 1.1 times 1 µF 10 V IN-L-ch. (Line,HP)
29 28
OUT-R-ch. (Line) 4.7 µF 10 V 1.1 times 1 µF 10 V IN-R-ch. (Line,HP)
30 27
−9.17 dBV −10 dBV
STBY Standby Line GND
31 mute 26
1 µF 10 V
BEEP_IN Switch B-2
32 Timer 25
Switch B Switch B-1
33 24
Switch A-3
34 23
10 µF 10 V +
GND Switch A-2
35 + 22
Switch A-1
36 21
EVR EVR
N.C. (Test out) BVREF
37 Charge 20
10 µF 10 V pump
EVRCTL
38 19
10 µF 16 V
VREF
39 18
Headphone 6 dB
−4 dBV Offset Switch A
68 Ω 40 cancel 17
−4 dBV Offset 10 µF 16 V
VCC
cancel
32 Ω 68 Ω 41 16
6 dB
Power Save
42 save CTL 15
10 µF 16 V 0.47 µF 10 V
VREF (SP)
43 14
−13 dBV −3 dB 0.47 µF 10 V
52 5
−2 dBV −2 dBV
4 dBV 53 Power 4 4 dBV
L-ch. SP out save R-ch. SP out
8 Ω to 16 Ω 8 Ω to 16 Ω
−2 dBV 54 3
−2 dBV
55 14 dB 14 dB 2
VCC_SP VCC_SP
56 1
1 µF 10 V 1 µF 10 V
Supply voltage 5 V
SDC00057AEB 4
AN12943A
Pin Descriptions
SDC00057AEB 5
AN12943A
SDC00057AEB 6
AN12943A
A
Parameter Symbol Rating Unit Note
No.
VCC 5.75
1 Supply voltage V *1
VCC_SP 5.75
2 Supply current ICC A
3 Power dissipation PD 517 mW *2
4 Storage temperature Tstg −55 to +150 ºC *3
5 Operating ambient temperature Topr −20 to +75 ºC *3
6 Operating ambient atmospheric pressure Popr 1.013 × 105 ± 0.61 × 105 Pa
7 Operating constant gravity Gopr 9 810 m/s2
8 Operating shock Sopr 4 900 m/s 2
Note) *1: The values under the condition not exceeding the above absolute maximum ratings and the power dissipation.
*2: When using this IC, referring to Technical Data, y Power dissipation of package HSOP056-P-0300A.
Be sure to use the IC so that the power dissipation of the IC without heat sink will not exceed 517 mW at Ta = 75ºC.
*3: Except for the operating ambient temperature and storage temperature, all ratings are for Ta = 25ºC.
SDC00057AEB 7
AN12943A
B Test Limits
Parameter Symbol Conditions Unit Note
No. circuits min typ max
Circuit current
Circuit current 1A at non-signal
1 IT1A 1 50 100 µA
(VCC_SP) VCC = 5.00 V, at non-signal,
Circuit current 2A at non-signal at automatic distinction: on
2 IT2A 1 20.0 29.0 38.0 mA
(VCC)
Circuit current 1B at non-signal
3 IT1B 1 VCC = 5.00 V, at non-signal, 15.0 25.0 mA
(VCC_SP)
SP power save: off,
Circuit current 2B at non-signal at automatic distinction: off
4 IT2B 1 21.0 30.0 39.0 mA
(VCC)
Circuit current 1C at non-signal
5 IT1C 1 VCC = 5.00 V, at non-signal, 55 100 µA
(VCC_SP)
SP power save: on,
Circuit current 2C at non-signal at automatic distinction: off
6 IT2C 1 19.0 28.0 37.0 mA
(VCC)
Standby current 1 at non-signal
7 IST1 1 16 100 µA
(VCC_SP) VCC = 5.00 V,
Standby current 2 at non-signal at standby mode
8 IST2 1 17 100 µA
(VCC)
Speaker amplifier (RL = 8 Ω): Speaker_input (pin 44, pin 45) → Speaker_output (pin 2 to pin 5, pin 52 to pin 55)
9 Output level L-channel VSPL 1 VIN = −13 dBV, f = 1 kHz, 2.0 4.0 6.0 dBV
10 Output level R-channel VSPR 1 RL = 8 Ω 2.0 4.0 6.0 dBV
11 Output distortion L-channel THSL 1 VIN = −13 dBV, f = 1 kHz, 0.04 0.5 %
12 Output distortion R-channel THSR 1 RL = 8 Ω, to THD fifth 0.04 0.5 %
Maximum output electric power
13 VMAXSL 1 0.7 0.81 W
L-channel VIN = 1 kHz, THD = 1%,
Maximum output electric power RL = 8 Ω
14 VMAXSR 1 0.7 0.81 W
R-channel
15 Output noise L-channel VNSL 1 Rg = 1 kΩ, RL = 8 Ω, −89 −67 dBV
16 Output noise R-channel VNSR 1 A curve filter −89 −67 dBV
VIN = −13 dBV, f = 1 kHz,
17 Channel balance CHBS 1 −1 0 1 dB
RL = 8 Ω
18 Cross talk in L-channel CTLSLR 1 VIN = −13 dBV, f = 1 kHz, 70 90 dB
19 Cross talk in R-channel CTLSRL 1 RL = 8 Ω, A curve filter 70 90 dB
Headphone amplifier (RL = 32 Ω): L-channel, R-channel_input (pin 28, pin 27) → Headphone_output (pin 40, pin 41)
20 Output level L-channel VHPL 1 VIN = −10 dBV, RL = 100 Ω −5.0 −4.0 −3.0 dBV
21 Output level R-channel VHPR 1 Vol = 3.3 V (max), f = 1 kHz −5.0 −4.0 −3.0 dBV
VIN = −10 dBV, RL = 100 Ω
22 Channel balance CHBH 1 Vol = 3.3 V (max), f = 1 kHz −1.0 0.0 1.0 dB
R-ch./L-ch. difference
SDC00057AEB 8
AN12943A
B Test Limits
Parameter Symbol Conditions Unit Note
No. circuits min typ max
Headphone Amplifier (RL = 32 Ω) (continued): L-channel, R-channel_input (pin 28, pin 27) → Headphone_output (pin 40, pin 41)
23 Output distortion L-channel THHL 1 VOUT = −14 dBV, RL = 100 Ω 0.03 0.1 %
Vol = 3.3 V (max), f = 1 kHz
24 Output distortion R-channel THHR 1 to THD fifth 0.03 0.1 %
25 Maximum input level L-channel VMAHIL 1 THD = 1%, RL = 100 Ω 0.0 4.7 dBV
26 Maximum input level R-channel VMAHIR 1 Vol = 1.65 V (typ), f = 1 kHz 0.0 4.7 dBV
27 Maximum output level L-channel VMAHOL 1 THD = 1%, RL = 100 Ω 0.0 3.4 dBV
28 Maximum output level R-channel VMAHOR 1 Vol = 3.3 V (max), f = 1 kHz 0.0 3.4 dBV
29 Output noise L-channel VNHL 1 −94 −79 dBV
Rg = 1 kΩ, A curve filter
30 Output noise R-channel VNHR 1 −94 −79 dBV
31 Cross talk in L-channel CTLHLR 1 VIN = −10 dBV, RL = 100 Ω 60 79 dB
32 Cross talk in R-channel CTLHRL 1 f = 10 kHz, A curve filter 60 79 dB
33 Beep output level L-channel BEHL 1 VIN = 3.3 VPP, RL = 100 Ω 0.28 0.58 VPP
34 Beep output level R-channel BEHR 1 1 cycle = 1 ms 0.28 0.58 VPP
Volume part: L-channel, R-channel_input (pin 28, pin 27) → Headphone_output (pin 40, pin 41)
35 Medium voltage gain L-channel VOLL 1 VIN = −20 dBV, f = 1 kHz, −32.5 −30.0 −27.5 dBV
36 Medium voltage gain R-channel VOLR 1 Vol = 1.65 V (typ) −32.5 −30.0 −27.5 dBV
VIN = −20 dBV, f = 1 kHz,
Channel balance at the time of the
37 VCHB 1 Vol = 1.65 V (typ) −2.0 0.0 2.0 dB
medium gain
R-ch./L-ch. difference
Volume maximum attenuation
38 VOLNL 1 VIN = −10 dBV, f = 1 kHz, 70 90 dB
quantity L-channel
Vol = 0.0 V (min),
Volume maximum attenuation A curve filter
39 VOLNR 1 70 90 dB
quantity R-channel
Line amplifier part: L-channel, R-channel_input (pin 28, pin 27) → Line_output (pin 29, pin 30)
40 Output level L-channel VHLL 1 VIN = −10 dBV, −10.0 −9.2 −8.4 dBV
41 Output level R-channel VHLR 1 RL = 10 kΩ, f = 1 kHz −10.0 −9.2 −8.4 dBV
VIN = −10 dBV,
42 Channel balance CHBL 1 RL = 10 kΩ, f = 1 kHz, − 0.8 0.0 0.8 dB
R-ch./L-ch. difference
43 Output distortion L-channel THLL 1 VIN = −10 dBV, RL = 10 kΩ, 0.003 0.03 %
44 Output distortion R-channel THLR 1 f = 1 kHz, to THD fifth 0.003 0.03 %
45 Maximum output level L-channel VMALL5 1 THD = 1%, RL = 10 kΩ 0.0 4.1 dBV
46 Maximum output level R-channel VMALR5 1 f = 1 kHz 0.0 4.1 dBV
47 Output noise L-channel VNLL 1 −105 −87 dBV
Rg = 1 kΩ, A curve filter
48 Output noise R-channel VNLR 1 −105 −87 dBV
SDC00057AEB 9
AN12943A
B Test Limits
Parameter Symbol Conditions Unit Note
No. circuits min typ max
Line amplifier part (continued): L-channel, R-channel_input (pin 28, pin 27) → Line_output (pin 29, pin 30)
49 Cross talk in L-channel CTLLLR 1 VIN = −10 dBV, RL = 10 kΩ 60 88 dB
50 Cross talk in R-channel CTLLRL 1 f = 10 kHz, A curve filter 60 88 dB
Automatic signal detection part: L-channel, R-channel_input (pin 28, pin 27) → Signal detection preamplifier output (pin 12)
Preamplifier output voltage level
51 VSDTL 1 −13 −10 −7 dBV
L-channel entry VIN = −49 dBV, f = 1 kHz
Preamplifier output voltage level Vol = 1.65 V (typ)
52 VSDTR 1 −13 −10 −7 dBV
R-channel entry
Signal detection limit entry voltage
53 VSDTTHL 1 −70 −65 −60 dBV
level L-channel VIN = 1 kHz
Signal detection limit entry voltage Vol = 1.65 V (typ)
54 VSDTTHR 1 −70 −65 −60 dBV
level R-channel
Other part
SP output DC offset voltage
55 VDCSPL 1 −112 0 112 mV
L-channel DC voltage bitween positive
SP output DC offset voltage and opposite at non-signal
56 VDCSPR 1 −112 0 112 mV
R-channel
57 Output at SP power save L-channel VPSPPSL 1 VIN = −13 dBV, f = 1 kHz, −114 −70 dBV
58 Output at SP power save R-channel VPSPPSR 1 RL = 8 Ω, A curve filter −114 −70 dBV
Signal detection part
59 VSDTLO 1 At non-signal, A curve filter −62 −44 dBV
Preamplifier output noise
Switch switching-over voltage level
60 Standby on STON GND 0.8 V
61 Standby off STOF 2.0 3.6 V
62 SPK mute on SPMON GND 0.8 V
63 SPK mute off SPMOF 2.0 5.5 V
64 Headphone jack on HPJON GND 0.8 V
65 Headphone jack off HPJOF 2.0 5.5 V
Signal automatic detection feature
66 ATON GND 0.8 V
on
Signal automatic detection feature
67 ATOF 2.0 5.5 V
off
68 Switch A off CMUOF GND 0.8 V
69 Switch A on CMUON 2.0 5.5 V
70 Switch B off DMUOF GND 0.8 V
71 Switch B on DMUON 2.0 5.5 V
SDC00057AEB 10
AN12943A
Voltage
Pin No. Description Remarks
Low High
17 Switch A on/off Off On
STB on STB off
(LINE MUTE on) (LINE MUTE off)
31 Standby on/off
(HP SAVE on) (HP SAVE off)
(HP MUTE on) (HP MUTE off)
33 Switch B on/off Off On
The signal automatic detection feature Automatic Automatic
49
on/off distinction: off distinction: on
Voltage
Pin No. Description Both pin 47 and Either pin 47 or Remarks
pin 50 = High pin 50 = Low
SPK SPK It has priority over power saving by
47 HP JACK
power save off power save on pin 47 and pin 50 more than an
50 SPK MUTE
(SP on) (SP off) automatic detection.
SDC00057AEB 11
AN12943A
Technical Data
y Circuit diagrams of the input/output part and pin function descriptions
Note) The characteristics listed below are reference values based on the IC design and are not guaranteed.
Pin Waveform
Inner circuit Impedance Description
No. and voltage
Power supply pins specifically designed
for speaker amplifiers.
VCC_SP • Pin 1 for R-channel.
1, • Pin 56 for L-channel.
56 Because the big electric current flows, it
DC: 5.0 V is desirable to separate from the VCC line
to the other power supply pins on the
board pattern.
Output pins of speaker amplifiers.
Speaker output It becomes BTL output.
Pin 2, pin 3 • Pin 2, pin 3 for R-channel positive
2, Pin 54, pin 55 VCC_SP
(5.0 V) Pin 2 phase output
3, Positive phase 3 • Pin 4, pin 5 for R-channel negative
4, 54
55 phase output
5, 20k The output • Pin 54, pin 55 for L-channel positive
Pin 4, pin 5 impedance: Equal phase output
52, Pin 52, pin 53 to or less than 1 Ω
• Pin 52, pin 53 for L-channel negative
53, Negative phase 4k Pin 4 phase output
54, 5
52 To reduce voltage loss caused by the
55 53 wire resistance in maximum output, it
DC: 2.20 V makes output 2 terminals.
AC: 4 dBV When the speaker amplifiers save power,
DC voltage is also kept.
It is GND pin for the speaker amplifier.
• Pin 6 is for R-channel.
GND_SP • Pin 51 is for L-channel.
6,
Because the big electric current flows, it
51 is desirable to separate from the GND
DC: 0.0 V line to the other GND pin on the board
pattern. Also, it isn't connected with the
substrate potential in the IC.
Audio automatic VREG (4.5 V) It connects a condenser for the peak
detection Signal less time:
detection. It is the circuit which detects
detection pin: Constant current
1k source a peak after rectifying the audio signal
7 Signal's there of the audio signal automatic detection
7 Signal nothing
being: circuit in both waves. By changing a
DC: 0.0 V capacity value, the time which the power
The output
Signal's there 100k impedance: saving depends on in case of the
being switchover which is without signal with
About 1 kΩ
DC: 2.0 V VSS (−2.6 V) signal's there being can be changed.
8, NC
10,
37,
46
SDC00057AEB 12
AN12943A
Pin Waveform
Inner circuit Impedance Description
No. and voltage
9, GND It is the GND pins of the signal system.
26, It isn't connected with the substrate
48 DC: 0.0 V potential in the IC.
VREG (4.5 V)
The signal
detection system
preamplifier
output pin The output
It is the output pin of the signal detection
12 12 impedance: About
system preamplifier.
10 Ω
DC: 2.25 V
AC: −10 dBV
VSS (−2.6 V)
VREG (4.5 V)
Offset
cancellation C It is the condenser connection pin of the
13, pin The entry offset cancellation circuit to remove the
Pin 13 impedance: About DC offset. As the principle, it composes
14 100k high pass filter by entry impedance "R"
14 100 kΩ
and connection condenser "C".
DC: 2.25 V
VSS (−2.6 V)
SDC00057AEB 13
AN12943A
Pin Waveform
Inner circuit Impedance Description
No. and voltage
It is the power supply (VCC) pin to supply
VCC the regulator circuit to create the inner
power supply VREG with the voltage. It is
16 separating from VCC_SP of pin 1, pin 56
fully inside. It is desirable to separate as
DC: 5.0 V far as it finishes coming out about the P
board pattern, too.
Switch A/B 100k
on/off Pin 17
33 It change the switch A, B on/off.
17, The entry
impedance: About • High: On
33 100 kΩ • Low: Off
DC: 0 V 300k
(at Open) VSS (−2.6 V)
VCC (5 V)
VSS (−2.6 V)
100k
19
EVR control for It is the pin which controls EVR for
SP and HP The entry speaker amplifier and Headphone
19 impedance: The amplifier.
high impedance The holding range with control voltage is
DC: V 0 V to 3.3 V.
VSS (−2.6 V)
VREG (4.5 V)
BVREF
The entry
It is the input pin of DC voltage for
20 impedance: The
20 switch A-1, A-2, A-3, B-1, B-2 output.
high impedance
DC: V
VSS (−2.6 V)
SDC00057AEB 14
AN12943A
Pin Waveform
Inner circuit Impedance Description
No. and voltage
21, Switch A-1 Pin 21
VREG (4.5 V) 22
22, Switch A-2
23
23, Switch A-3 24
25 The output
Switch B-1 impedance: Equal It is the output pin of DC voltage. It
24,
to or less than outputs pin 20 (BVREF) input voltage.
25 Switch B-2
about 10 Ω
Audio signal
input 14.6k 50k
The entry It enters a main audio signal.
27,
impedance: About • Pin 27: R-channel entry
28
25k 25 kΩ • Pin 28: L-channel entry
DC: 2.25 V
AC: −10 dBV
VSS 35.4k
(−2.6 V)
VREF (2.25 V)
VCC (5.0 V)
Line out
Pin 29 The output
30 It is the output pin of the line amplifier.
29, 17.8k impedance: Equal
• Pin 29: L-channel output
30 to or less than
AC: −9.17 dBV 32.2k about 10 Ω • Pin 30: R-channel output
DC: 2.25 V
VSS (−2.6 V)
VREG (4.5 V)
The range under
It changes whether or not it makes
about 1.5 V.
100k this IC an operation condition or
Standby on/off 250k The entry
changing SW 100k impedance: About whether or not it makes it a standby.
31 210 kΩ • Low: Standby
31
The range over • High: The operation condition
200k about 1.5 V.
DC: 2.0 V 300k In that the power changes a connected
The entry
condition to the standby, the circuit
impedance: About
electric current can be almost made 0.
68 kΩ
VSS (−2.6 V)
SDC00057AEB 15
AN12943A
Pin Waveform
Inner circuit Impedance Description
No. and voltage
200
32
Beep entry It is the entry pin to enter beep signal.
The entry The same signal is entered both by
32 impedance: About L-channel and R-channel with the beep
DC: 2.25 V 7.5k 200 Ω signal mix amplifier of the following
AC: 3.3 VPP paragraph.
VSS 20k
(−2.6 V)
VREF (2.25 V)
VREGDIG (2.7 V)
Capacitor
connect pin 1 for The output
charge pump impedance: Equal It is the condenser connection pin for
34 GND
to or less than charge pump.
about 10 Ω
DC: V
34
GND
It is GND pin for charge pump.
35 It isn't connected with other GND pin in
the IC.
DC: 0.0 V
36
Capacitor
connect pin 2 for The output
charge pump impedance: Equal It is the condenser connection pin for
36
to or less than charge pump.
about 10 Ω
DC: V
VSS (−2.6 V)
SDC00057AEB 16
AN12943A
Pin Waveform
Inner circuit Impedance Description
No. and voltage
VCC (5.0 V)
Output terminal
for the HP
amplifier 20k The output It is an output pin for the headphone
40, Pin 40 impedance: Equal amplifier. The signal which was adjusted
41 to or less than in the volume in EVR can be output by
41
about 1 Ω the low impedance.
DC: 0 V 10k
AC: −4 dBV
VSS (−2.6
V)
VCC (5.0
V)
VREF (SP)
The entry It is the standard voltage pin to fix the
43 500k impedance: About DC bias of the speaker output. It
43
250 kΩ connects a condenser to remove a ripple.
DC: 2.20 V
500k
VSS (−2.6
V)
Pin 45
44 It is the voice input pins of the speaker
5.8k
Speaker amplifier. To make offset voltage in
amplifier entry power saving on/off changing by the
44, The entry speaker amplifier little, it combines
14.2k impedance: About capacity.
45 20 kΩ
DC: 2.25 V ( It makes POP noise small ).
AC: −13 dBV • Pin 44: R-channel speaker entry
VSS VREF • Pin 45: L-channel speaker entry
(−2.6 V) (2.25
V)
The range under
100k about 1.5 V.
47 The entry It is the pin which controls power saving
HP_JACK_IN
signal input pin impedance: The by the speaker amplifier. At the time of
high impedance on in addition to the control in case of
47
The range over automatic distinction function off, too,
about 1.5 V. power saving on by pin 47, pin 50 has
DC: VSS 300k The entry priority over.
(−2.6 V) impedance: About
100 kΩ
SDC00057AEB 17
AN12943A
Pin Waveform
Inner circuit Impedance Description
No. and voltage
VREG
(4.5 V)
Signal automatic 10k We change an audio signal automatic
detection detection function in on/off. In case of
function 275k automatic detection off, it controls power
100k The entry
on/off control 49 saving by speaker with the manual with
49 pin impedance: The the power saving on/off pin.
55k high impedance • High: Function on
• Low: Function off
10k
DC:
VSS (−2.6
V)
The range under
SP amplifier 100k about 1.5 V.
50 The entry It is the pin which controls power saving
power saving
on/off control impedance: The by the speaker amplifier. At the time of
pin high impedance on in addition to the control in case of
50
The range over automatic distinction function off, too,
about 1.5 V. power saving on by pin 47, pin 50 has
VSS 300k The entry priority over.
DC: (−2.6 V)
impedance: About
100 kΩ
SDC00057AEB 18
AN12943A
Control timing
VCC_SP
(Pin 1, pin 56) As for the occurrence of
time-lag between VCC -on and
VCC_SP-on, no problem.
As for the occurrence
of time-lag between
VCC VCC -off and VCC_SP-
(Pin 16) off, no problem.
Note) The characteristics listed above are reference values based on the IC design and are not guaranteed.
SDC00057AEB 19
AN12943A
PD Ta
5.000
4.280
4.000
Mounted on four layers of
standard board
Power dissipation PD (W)
1.000 0.862
Independent IC
without a heat sink
Rth(j-a) = 144.9°C/W
0.000
0 25 50 75 100 125 150
Ambient temperature Ta (°C)
Note) The characteristics listed above are reference values based on the IC design and are not guaranteed.
y Usage notes
1. Please carry out the thermal design with sufficient margin such that the power dissipation will not be exceeded, based on the
conditions of power supply, load and surrounding temperature.
Although indicated also in the column of the maximum rating, the maximum rating becomes an instant and the marginal value
which must not exceed. It sufficiently evaluates, and I use-wish-do so that it may not exceed certainly.
Moreover, don't impress neither voltage nor current to pin which is not indicated. It may destroy in both cases.
2. Please pay attention in the pattern layout in order to prevent damage due to short circuit between pins.
In addition, for the pin configuration, please refer to Pin Descriptions.
3. Please absolutely do not mount the LSI in the reverse direction on to the printed-circuit-board.
It might be damaged when the electricity is turned on.
4. Please do a visual inspection on the printed-circuit-board before turning on the power supply, otherwise damage might happen
due to problems such as a solder-bridge between the pins of the semiconductor device.
Also perform a full technical verification on the assembly quality, because the same damage possibly can happen due to
conductive substances, such as solder ball, that adhere to the LSI during transportation.
5. Please take notice in the use of this product that it might break or occasionally smoke when an abnormal state occurs such as
output pin, pin 34 and pin 36 (capacitor connect pin 1, 2 for charge pump), pin 38 and pin 39 (VSS) − power supply pin short,
output pin, pin 34 and pin 36, pin 38 and pin 39 − GND short, or output-to-output-pin short (load short), pin 34 − pin 36 short.
And, safety measures such as an installation of fuses are recommended because the extent of the above-mentioned damage and
smoke emission will depend on the current capability of the power supply.
6. When using the LSI for model deployment or new products, perform fully the safety verification including the long-turm
reliability for each product.
SDC00057AEB 20
AN12943A
55) (dBV)
5) (dBV)
10 10
[dBV]
[dBV]
level (Pin 2 to pin
SP出力レベル(52-55pin)
SP出力レベル(2-5pin)
-10 -10
-20
SP output
-20
VCC = 5.0 V, VCC_SP = 5.0 V, freq = 1 kHz, EVR = 3.3 V, LINE VCC = 5.0 V, VCC_SP = 5.0 V, freq = 1 kHz, EVR = 3.3 V, LINE
input (pin 27), 24 kΩ-ATT, Automatic detection on, HPF: 400 Hz, input (pin 28), 24 kΩ-ATT, Automatic detection on, HPF: 400 Hz,
LPF: 30 kHz LPF: 30 kHz
I/O characteristics − 8 Ω
SP入出力特性-8Ω
Speaker Speaker I/O characteristics − 8 Ω
SP入出力特性-8Ω
SP output distortion
SP出力歪率(Lch→Lch)
(Pin 52 to pin 55) THD (%)
10 10
SP出力歪率(52-55pin) THD [%]
SP出力歪率(2-5pin) THD [%]
1 1
SP output distortion
SP output distortion
0.1 0.1
0.01 0.01
-40 -30 -20 -10 0 -40 -30 -20 -10 0
入力レベル(Rch-27pin)
Input level (R-channel - Pin[dBV]
27) (dBV) 入力レベル(Lch-28pin)
Input level (L-channel - Pin[dBV]
28) (dBV)
VCC = 5.0 V, VCC_SP = 5.0 V, VIN = −10 dBV, EVR = 3.3 V, LINE VCC = 5.0 V, VCC_SP = 5.0 V, VIN = −10 dBV, EVR = 3.3 V, LINE
input (pin 27), 24 kΩ-ATT, Automatic detection on input (pin 28), 24 kΩ-ATT, Automatic detection on
frequency characteristics − 8 Ω
SP出力周波数特性-8Ω
Speaker output Speaker output frequency characteristics − 8 Ω
SP出力周波数特性-8Ω
SP output level SP output level
SP出力レベル(Rch→Rch)
(R-channel → R-channel) SP出力レベル(Lch→Lch)
(L-channel → L-channel)
10 10
level (Pin 2 to pin 5) (dBV)
pin 55)
output level (Pin 52 to[dBV]
SP出力レベル(2-5pin)[dBV]
8 8
SPSP出力レベル(52-55pin)
6 6
(dBV)
4 4
2 2
SP output
0 0
0.01 0.1 1 10 100 0.01 0.1 1 10 100
入力周波数(Rch-27pin) [kHz]
Input frequency (R-channel - Pin 27) (kHz) 入力周波数(Lch-28pin) [kHz]
Input frequency (L-channel - Pin 28) (kHz)
SDC00057AEB 21
AN12943A
10 10
SP出力歪率(52-55pin) THD [%]
SP出力歪率(2-5pin) THD [%]
1 1
SP output distortion
SP output distortion
0.1 0.1
0.01 0.01
0.01 0.1 1 10 100 0.01 0.1 1 10 100
入力周波数(Rch-27pin) [kHz]
Input frequency (R-channel - Pin 27) (kHz) 入力周波数(Lch-28pin) [kHz]
Input frequency (L-channel - Pin 28) (kHz)
VCC = 5.0 V, VCC_SP = 5.0 V, VIN = −10 dBV, EVR = 3.3 V, LINE VCC = 5.0 V, VCC_SP = 5.0 V, VIN = −10 dBV, EVR = 3.3 V, LINE
input (pin 28), 24 kΩ-ATT, Automatic detection on, 30 kHz: LPF input (pin 27), 24 kΩ-ATT, Automatic detection on, 30 kHz: LPF
cross talk frequency characteristics − 8 Ω
SP-L/RSP-L/Rクロストーク周波数特性-8Ω cross talk frequency characteristics − 8 Ω
SP-L/RSP-L/Rクロストーク周波数特性-8Ω
cross talk (R-channel → L-channel) (dB)
cross talk (L-channel → R-channel) (dB)
60 60
70 70
80 80
SP output
90 90
0.01 0.1 1 10 100 0.01 0.1 1 10 100
入力周波数(Lch-28pin) [kHz]
Input frequency (L-channel - Pin 28) (kHz) 入力周波数(Rch-27pin) [kHz]
Input frequency (R-channel - Pin 27) (kHz)
SDC00057AEB 22
AN12943A
10
HPアンプ出力(40pin)レベル[dBV]
HPアンプ出力(41pin)レベル[dBV]
0 0
-10 -10
HP amplifier
HP amplifier
-20 -20
-30 -30
-30 -20 -10 0 10 -30 -20 -10 0 10
入力レベル(27pin)
Input level (Pin 27)[dBV]
(dBV) 入力レベル(28pin)
Input level (Pin 28)[dBV]
(dBV)
VCC = 5.0 V, VCC_SP = 5.0 V, freq = 1 kHz, Rout = 100 Ω, EVR = 3.3 V, Automatic detection on, HPF: 400 Hz, LPF: 30 kHz
HPアンプ入出力歪率特性-EVR=max
Headphone amplifier I/O distortion characteristics - EVR =(片ch入力)
max (Single-channel input) HPアンプ入出力歪率特性-EVR=max
Headphone amplifier I/O distortion characteristics - EVR =(片ch入力)
max (Single-channel input)
HP amplifier output distortion (%) HP amplifier output distortion (%)
HPアンプ出力歪率[%](Rch→Rch)
(R-channel → R-channel) HPアンプ出力歪率[%](Lch→Lch)
(L-channel → L-channel)
THD [%]THD (%)
10 10
output (Pin 41) distortion
1 1
HPアンプ出力(41pin)歪率
HPアンプ出力(40pin)歪率
0.1 0.1
HP amplifier
HP amplifier
0.01 0.01
-30 -20 -10 0 10 -30 -20 -10 0 10
入力レベル(27pin)
Input level (Pin 27)[dBV]
(dBV) 入力レベル(28pin)
Input level (Pin 28)[dBV]
(dBV)
VCC = 5.0 V, VCC_SP = 5.0 V, VIN = −10 dBV, Rout = 100 Ω, EVR = 3.3 V, Automatic detection on
HPアンプ周波数特性-EVR=max
Headphone amplifier frequency characteristics - EVR (片ch入力)
= max (Single-channel input) HPアンプ周波数特性-EVR=max
Headphone amplifier frequency characteristics - EVR(片ch入力)
= max (Single-channel input)
HP amplifier output (dBV) HP amplifier output (dBV)
HPアンプ出力[dBV](Rch→Rch)
(R-channel → R-channel) HPアンプ出力[dBV](Lch→Lch)
(L-channel → L-channel)
output (Pin 40) level (dBV)
output (Pin 41) level (dBV)
-2 -2
HPアンプ出力(41pin)レベル[dBV]
HPアンプ出力(40pin)レベル[dBV]
-3 -3
-4 -4
HP amplifier
HP amplifier
-5 -5
-6 -6
0.01 0.1 1 10 100 0.01 0.1 1 10 100
Input入力周波数(27pin) [kHz]
frequency (Pin 27) (kHz) 入力周波数(28pin)
Input [kHz]
frequency (Pin 28) (kHz)
SDC00057AEB 23
AN12943A
10 10
output (Pin 41) distortion
HPアンプ出力(40pin)歪率
HPアンプ出力(41pin)歪率
0.1 0.1
HP amplifier
HP amplifier
0.01 0.01
0.01 0.1 1 10 100 0.01 0.1 1 10 100
Input入力周波数(27pin) [kHz]
frequency (Pin 27) (kHz) Input入力周波数(28pin) [kHz]
frequency (Pin 28) (kHz)
VCC = 5.0 V, VCC_SP = 5.0 V, VIN = −10 dBV, EVR = 3.3 V, Rout = 100 Ω, Automatic detection on, 30 kHz: LPF
Headphone amplifier: Cross talk - EVR = max (L-channel → R-channel)
HPアンプ:クロストーク-EVR=max (Lch→Rch) amplifier: Cross talk - EVR = max (L-channel → R-channel)
HPアンプ:クロストーク-EVR=max (Lch→Rch)
Headphone
HP cross talk (dB) HP cross talk (dB)
HPクロストーク[dB](Lch→Rch)
(L-channel → R-channel) HPクロストーク[dB](Rch→Lch)
(R-channel → L-channel)
50 50
60 60
talk (dB)
talk (dB)
クロストーク[dB]
クロストーク[dB]
70 70
Cross
Cross
80 80
90 90
100 100
0.01 0.1 1 10 100 0.01 0.1 1 10 100
入力周波数
Input [kHz]
frequency (kHz) 入力周波数
Input [kHz]
frequency (kHz)
SDC00057AEB 24
AN12943A
10 10
ラインアンプ1出力(29pin)レベル[dBV]
ラインアンプ出力(30pin)レベル[dBV]
0 0
-10 -10
Line amplifier
Line amplifier
-20 -20
-30 -30
-30 -20 -10 0 10 -30 -20 -10 0 10
入力レベル(27pin)
Input level (Pin 27)[dBV]
(dBV) 入力レベル(28pin)
Input level (Pin 28)[dBV]
(dBV)
VCC = 5.0 V, VCC_SP = 5.0 V, freq = 1 kHz, RL = 10 kΩ, RL(HP) = 100 Ω, EVR = 3.3 V, Automatic detection on, HPF: 400 Hz, LPF: 30 kHz
ラインアンプ入出力歪率特性 (片ch入力)
Line amplifier I/O distortion characteristics (Single-channel input) ラインアンプ入出力歪率特性 (片ch入力)
Line amplifier I/O distortion characteristics (Single-channel input)
Line amplifier output distortion (%) Line amplifier output distortion (%)
ラインアンプ出力歪率[%](Rch→Rch)
(R-channel → R-channel) ラインアンプ出力歪率[%](Lch→Lch)
(L-channel → L-channel)
10 10
[%] (%)
[%] (%)
THDTHD
THDTHD
1 1
amplifier output (Pin 29) distortion
amplifier output (Pin 30) distortion
Line ラインアンプ出力(30pin)歪率
Lineラインアンプ出力(29pin)歪率
0.1 0.1
0.01 0.01
0.001 0.001
0.0001 0.0001
-30 -20 -10 0 10 -30 -20 -10 0 10
入力レベル(27pin)
Input level (Pin 27)[dBV]
(dBV) 入力レベル(28pin)
Input level (Pin 28)[dBV]
(dBV)
VCC = 5.0 V, VCC_SP = 5.0 V, VIN = −10 dBV, RL = 10 kΩ, RL(HP) = 100 Ω, EVR = 3.3 V, Automatic detection on
Line amplifier frequency characteristics (Single-channel input)
ラインアンプ周波数特性 (片ch入力) Line amplifier frequency characteristics (Single-channel input)
ラインアンプ周波数特性 (片ch入力)
Line amplifier output (dBV) Line amplifier output (dBV)
ラインアンプ出力[dBV](Rch→Rch)
(R-channel → R-channel) ラインアンプ出力[dBV](Lch→Lch)
(L-channel → L-channel)
output (Pin 29) level (dBV)
output (Pin 30) level (dBV)
-7 -7
ラインアンプ出力(30pin)レベル[dBV]
ラインアンプ出力(29pin)レベル[dBV]
-8 -8
-9 -9
-10 -10
Line amplifier
Line amplifier
-11 -11
-12 -12
0.01 0.1 1 10 100 0.01 0.1 1 10 100
Input入力周波数(27pin) [kHz]
frequency (Pin 27) (kHz) 入力周波数(28pin)
Input [kHz]
frequency (Pin 28) (kHz)
SDC00057AEB 25
AN12943A
THD (%)
THD (%)
10 10
THD [%]
THD [%]
ラインアンプ出力(29pin)歪率
ラインアンプ出力(30pin)歪率
0.1 0.1
0.01 0.01
Line amplifier
Line amplifier
0.001 0.001
0.0001 0.0001
0.01 0.1 1 10 100 0.01 0.1 1 10 100
Input入力周波数(27pin) [kHz]
frequency (Pin 27) (kHz) Input入力周波数(28pin) [kHz]
frequency (Pin 28) (kHz)
VCC = 5.0 V, VCC_SP = 5.0V, VIN = −10 dBV, RL = 10 kΩ, RL(HP) = 100 Ω, EVR = 3.3 V, Automatic detection on, 30 kHz: LPF
Line amplifier: Cross talk frequency characteristics (L-channel → R-channel)
ラインアンプ:クロストーク周波数特性(Lch→Rch) Cross talk frequency characteristics (R-channel → L-channel)
ラインアンプ:クロストーク周波数特性(Rch→Lch)
Line amplifier:
Cross talk (dB) Cross talk (dB)
クロストーク [dB] (Lch→Rch)
(L-channel → R-channel) クロストーク [dB] (Rch→Lch)
(R-channel → L-channel)
→ L-channel)
→ R-channel)
50 50
60 60
[dB] (Lch→Rch)
[dB] (Rch→Lch)
70 70
(dB) (R-channel
(dB) (L-channel
80 80
Cross talkクロストーク
Cross talkクロストーク
90 90
100 100
110 110
0.01 0.1 1 10 100 0.01 0.1 1 10 100
入力周波数(Lch-28pin)
Input frequency [kHz]
(L-channel - Pin 28) (kHz) 入力周波数(Rch-27pin)
Input frequency [kHz]
(R-channel - Pin 27) (kHz)
SDC00057AEB 26
AN12943A
-20
HPアンプ出力(40pin)レベル[dBV]
-20
-30 -30
-40 -40
-50 -50
-60 -60
-70 -70
HP amplifier
HP amplifier
-80 -80
-90 -90
-100 -100
0 0.5 1 1.5 2 2.5 3 3.5 4 0 0.5 1 1.5 2 2.5 3 3.5 4
EVR-CTL(19pin)
EVR-CTL (Pin 19)[V](V) EVR-CTL(19pin)
EVR-CTL [V](V)
(Pin 19)
VCC = 5.0 V, VCC_SP = 5.0 V, VIN = −10 dBV, freq = 1 kHz, ROUT = 100 Ω, Automatic detection on, HPF: 400 Hz, LPF: 30 kHz
EVR attenuate distortion characteristics − Headphone output
☆EVR減衰歪率特性-HP出力 characteristics − Headphone output
☆EVR減衰歪率特性-HP出力
EVR attenuate distortion
HP amplifier output distortion (%)
HPアンプ出力歪率[%](Rch→Rch)
(R-channel → R-channel)
HP amplifier output distortion (%)
HPアンプ出力歪率[%](Lch→Lch)
(L-channel → L-channel)
THD [%]THD (%)
10 10
output (Pin 41) distortion
1 1
HPアンプ出力(41pin)歪率
HPアンプ出力(40pin)歪率
0.1 0.1
0.01 0.01
HP amplifier
HP amplifier
0.001 0.001
0 0.5 1 1.5 2 2.5 3 3.5 4 0 0.5 1 1.5 2 2.5 3 3.5 4
EVR-CTL(19pin)
EVR-CTL [V](V)
(Pin 19) EVR-CTL(19pin)
EVR-CTL (Pin 19)[V](V)
SDC00057AEB 27
AN12943A
1 1
[Vrms] (Vrms)
[Vrms] (Vrms)
level - R-channel
level - L-channel
SP出力レベル-Rch
SP出力レベル-Lch
0.5 0.5
SP output
SP output
0 0
0.01 0.1 1 10 0.01 0.1 1 10
Beep入力レベル(32pin)
Beep input level (Pin 32)[Vrms]
(Vrms) Beep入力レベル(32pin)
Beep input level (Pin 32)[Vrms]
(Vrms)
VCC = 5.0 V, VCC_SP = 5.0 V, VIN = 1.0 Vrms, Input resistance = 10 kΩ, Square wave, EVR = 3.3 V (max), Automatic detection on
Beep frequency level characteristics: Speaker load − 8 Ω
Beep周波数レベル特性:SP負荷-8Ω level characteristics: Speaker load − 8 Ω
Beep周波数レベル特性:SP負荷-8Ω
Beep frequency
SP output level SP output level
SP出力レベル(BEEP→Rch)
(BEEP → R-channel) SP出力レベル(BEEP→Lch)
(BEEP → L-channel)
1 1
(Vrms)
(Vrms)
[Vrms]
[Vrms]
level - L-channel
level - R-channel
SP出力レベル-Lch
SP出力レベル-Rch
0.5 0.5
SP output
SP output
0 0
0.1 1 10 100 0.1 1 10 100
BeepBeep入力周波数(32pin) [kHz]
input frequency (Pin 32) (kHz) BeepBeep入力周波数(32pin) [kHz]
input frequency (Pin 32) (kHz)
SDC00057AEB 28
AN12943A
0 0
プリアンプ出力(12pin)レベル [dBV]
プリアンプ出力(12pin)レベル [dBV]
-10 -10
-20 -20
-30 -30
Preamplifier
Preamplifier
-40 -40
-50 -50
-80 -70 -60 -50 -40 -30 -20 -10 0 -80 -70 -60 -50 -40 -30 -20 -10 0
入力レベル(28pin)
Input level (Pin 28)[dBV]
(dBV) 入力レベル(27pin)
Input level (Pin 27)[dBV]
(dBV)
VCC = 5.0 V, VCC_SP = 5.0 V, VIN = −49 dBV, R-channel IN, RVR VCC = 5.0 V, VCC_SP = 5.0 V, VIN = −49 dBV, L-channel IN, EVR
= 3.3 V = 3.3 V
Signal detection preamplifier frequency characteristics
信号検出プリアンプ周波数特性 Signal detection preamplifier frequency characteristics
信号検出プリアンプ周波数特性
Preamplifier output (dBV) Preamplifier output (dBV)
プリアンプ出力[dBV](Rch)
(R-channel) プリアンプ出力[dBV](Lch)
(L-channel)
output (Pin 12) level (dBV)
0 0
プリアンプ出力(12pin)レベル [dBV]
プリアンプ出力(12pin)レベル [dBV]
-10 -10
-20 -20
-30 -30
Preamplifier
Preamplifier
-40 -40
-50 -50
0.01 0.1 1 10 100 0.01 0.1 1 10 100
Input入力周波数(28pin) [kHz]
frequency (Pin 28) (kHz) Input入力周波数(28pin) [kHz]
frequency (Pin 28) (kHz)
VCC = 5.0 V, VCC_SP = 5.0 V, VIN = −49 dBV, R-channel IN, EVR VCC = 5.0 V, VCC_SP = 5.0 V, VIN = −49 dBV, L-channel IN, EVR
= 3.3 V, LPF: R = 20 kΩ, C = 2 200 pF = 3.3 V, LPF: R = 20 kΩ, C = 2 200 pF
Signal detection preamplifier frequency characteristics
信号検出プリアンプ周波数特性 Signal detection preamplifier frequency characteristics
信号検出プリアンプ周波数特性
Post-LPF output (dBV)
LPF後出力[dBV](Rch)
(R-channel) Post-LPF output (dBV)
LPF後出力[dBV](Lch)
(L-channel)
0
output (Pin 11) level (dBV)
0
LPF後出力(11pin)レベル [dBV]
-10
LPF後出力(11pin)レベル [dBV]
-10
-20 -20
-30 -30
Post-LPF
-40
Post-LPF
-40
-50 -50
0.01 0.1 1 10 100 0.01 0.1 1 10 100
Input入力周波数(28pin) [kHz]
frequency (Pin 28) (kHz) Input入力周波数(27pin) [kHz]
frequency (Pin 27) (kHz)
SDC00057AEB 29
AN12943A
level (dBV)
0 0
-10 -10
-30 -30
(R-channel)
(L-channel)
EVR:typ EVR:typ
[dBV]
[dBV]
-40 -40
SPアンプ出力(Rch)レベル
SPアンプ出力(Lch)レベル
-50 -50
-60 -60
SP amplifier output
SP amplifier output
-70 -70
-80 -80
-90 -90
-100 -100
When input level was increased (Low-level → High-level)
入力レベルを増加(レベル小→レベル大)した場合 input level was increased (Low-level → High-level)
入力レベルを増加(レベル小→レベル大)した場合
When
-110 -110
-120 -120
-80 -70 -60 -50 -40 -30 -20 -10 0 -80 -70 -60 -50 -40 -30 -20 -10 0
Input level入力レベル(Rch入力)
(R-channel[dBV]
input) (dBV) Input level入力レベル(Lch入力)
(L-channel[dBV]
input) (dBV)
8) Mode switching
VCC = 5.0 V, VCC_SP = 5.0 V, VIN = −10 dBV, freq = 1 kHz, VCC = 5.0 V, VCC_SP = 5.0 V, VIN = −10 dBV, freq = 1 kHz,
R-channel input, RL = 8 Ω, HP_JACK = 5 V, EVR = 3.3 V R-channel input, RL = 8 Ω, SPK_MUTE = 5 V, EVR = 3.3 V
SPK-MUTE ON/OFF
SPK_MUTE on/off HP-JACK ON/OFF
HP_JACK on/off
SPOUT(VCC=4.4V)
SPOUT (VCC = 4.4 V) SPOUT(VCC=5V)
SPOUT (VCC = 5 V) SPOUT(VCC=5.6V)
SPOUT (VCC = 5.6 V)
SPOUT(VCC=4.4V)
SPOUT (VCC = 4.4 V) SPOUT(VCC=5V)
SPOUT (VCC = 5 V) SPOUT(VCC=5.6V)
SPOUT (VCC = 5.6 V)
20 20
0
[dBV] (dBV)
0
[dBV] (dBV)
-20 -20
(R-channel)
(R-channel)
-40 -40
SPOUT(Rch)
SPOUT(Rch)
-60 -60
SPOUT
SPOUT
-80 -80
-100 -100
-120 -120
0 1 2 3 4 5 0 1 2 3 4 5
CTL-Voltage(50pin)
CTL-Voltage (Pin 50)[V](V) CTL-Voltage(47pin)
CTL-Voltage (Pin 47)[V](V)
SDC00057AEB 30
AN12943A
-10 30
amplifier output [dBV]
-20 25
信号検出アンプ出力(12pin)
(mA)
IVCC [mA]
-30 20
IVCC
-40 15
-50 10
Signal detection
-60 5
-70 0
0 1 2 3 4 5 0 1 2 3 4 5
CTL-Voltage(49pin)
CTL-Voltage (Pin 49)[V](V) CTL-Voltage(31pin)
CTL-Voltage (Pin 31)[V](V)
VCC = 5.0 V, VCC_SP = 5.0 V, BVREF = 2.5 V, VIN = −10 dBV, f = 1 kHz
Switch A ON/OFF
Switch A on/off Switch B ON/OFF
Switch B on/off
SwitchA-3
Switch A-3(VCC=4.4V)
(VCC = 4.4 V) SwitchA-3
Switch A-3(VCC=5V)
(VCC = 5 V) SwitchA-3
Switch A-3(VCC=5.6V)
(VCC = 5.6 V) Switch B-2(VCC=4.4V)
Switch B-2 (VCC = 4.4 V) Switch B-2(VCC=5V)
Switch B-2 (VCC = 5 V) Switch B-2(VCC=5.6V)
Switch B-2 (VCC = 5.6 V)
-10 -10
-20 -20
(dBV)
(dBV)
(Pin 23)[dBV]
(Pin 25)[dBV]
-30 -30
-40 -40
A-3(23pin)
B-2(25pin)
-50 -50
-60 -60
SwitchB-2
SwitchA-3
-70 -70
Switch
Switch
-80 -80
-90 -90
-100 -100
0 1 2 3 4 5 0 1 2 3 4 5
CTL-Voltage(17pin)
CTL-Voltage [V](V)
(Pin 17) CTL-Voltage(33pin)
CTL-Voltage (Pin 33)[V](V)
Measurement Measurement
of AC level of AC level
AN12943A AN12943A
1 µF 10 kΩ AC input 1 µF 10 kΩ AC input
20 23 −10 dBV 20 25 −10 dBV
BVREF Switch 1 kHz BVREF Switch 1 kHz
10 kΩ 10 kΩ
2.5 V A-3 2.5 V B-2
17 33
Switch A Switch B
0 V to 5 V 0 V to 5 V
SDC00057AEB 31
Request for your special attention and precautions in using the technical information
and semiconductors described in this material
(1) An export permit needs to be obtained from the competent authorities of the Japanese Government if any of
the products or technical information described in this material and controlled under the "Foreign Exchange
and Foreign Trade Law" is to be exported or taken out of Japan.
(2) The technical information described in this material is limited to showing representative characteristics and
applied circuits examples of the products. It neither warrants non-infringement of intellectual property right
or any other rights owned by our company or a third party, nor grants any license.
(3) We are not liable for the infringement of rights owned by a third party arising out of the use of the technical
information as described in this material.
(4) The products described in this material are intended to be used for standard applications or general elec-
tronic equipment (such as office equipment, communications equipment, measuring instruments and house-
hold appliances).
Consult our sales staff in advance for information on the following applications:
• Special applications (such as for airplanes, aerospace, automobiles, traffic control equipment, combus-
tion equipment, life support systems and safety devices) in which exceptional quality and reliability are
required, or if the failure or malfunction of the products may directly jeopardize life or harm the human
body.
• Any applications other than the standard applications intended.
(5) The products and product specifications described in this material are subject to change without notice for
modification and/or improvement. At the final stage of your design, purchasing, or use of the products,
therefore, ask for the most up-to-date Product Standards in advance to make sure that the latest specifica-
tions satisfy your requirements.
(6) When designing your equipment, comply with the guaranteed values, in particular those of maximum rat-
ing, the range of operating power supply voltage, and heat radiation characteristics. Otherwise, we will not
be liable for any defect which may arise later in your equipment.
Even when the products are used within the guaranteed values, take into the consideration of incidence of
break down and failure mode, possible to occur to semiconductor products. Measures on the systems such
as redundant design, arresting the spread of fire or preventing glitch are recommended in order to prevent
physical injury, fire, social damages, for example, by using the products.
(7) When using products for which damp-proof packing is required, observe the conditions (including shelf life
and amount of time let standing of unsealed items) agreed upon when specification sheets are individually
exchanged.
(8) This material may be not reprinted or reproduced whether wholly or partially, without the prior written
permission of Matsushita Electric Industrial Co., Ltd.
2003 SEP