Professional Documents
Culture Documents
DIRECTIONS FOR USE For maximum chemical resistance while affording excellent
corrosion resistance and durability in non-salt atmospheres.
TINTING: May be tinted with HS tint colors only. Recommended for use in inland areas and for resistance to
acid and alkali. Sandblasting is recommended.
THINNING: See Application Data. National EPA, AIM and
VOC compliance levels will not be exceeded with these levels First coat Primer: 3 dry mils of 33010 (white) or 33514 (gray)
of thinner. or 33114 (coral) UREPRIME® HS2.
Note: Always know local VOC restrictions for coating applica- Topcoat: 3 dry mils of ACRYLITHANE™ HS2 in the desired
tions in your area before thinning this product. Thinning rec- color for the finish coat.
ommendations meet Federal VOC restrictions for architectural
coatings. This product and other referenced products may Clearcoat: 1 dry mil of ACRYLITHANE™ HS2 Clear (optional
not meet VOC restrictions for your application and may not be for ultimate gloss and durability).
available in your area. Carefully read and observe warning
on thinner labels. SYSTEM - C
APPLICATION: Mix thoroughly before use. Add 1 quart of Recommended for refurbishing existing equipment and struc-
99951 or 99961 per ¾ gallon unit of HS2 then mix thoroughly tures that have a surface suitable for refinishing by sanding
again. Only apply when air and surface temperature are and spot cleanup with hand and power tools.
between 40o – 100oF (7o - 38oC) and when the surface tem-
perature is at least 5 degrees (F) or 3 degrees (C) above the First coat Primer: 2 dry mils of 33010 (white) or 33514 (gray)
dew point. or 33114 (coral) UREPRIME® HS2 (preferred) or 3 mils of
15077 White STANTEST™ Primer or 15632 Gray STAN-
DRYING TIME: See Application Data for typical dry times. TEST™ Primer.
Low temperature, high humidity, poor ventilation and thick
films will retard drying. Accelerator 99041 may be added at Topcoat: 2 dry mils of ACRYLITHANE™ HS2 in the desired
the rate of up to 0.5 fl oz per mixed gallon of HS2 to reduce color for the finish coat.
the drying time.
Clearcoat: 1 dry mil of ACRYLITHANE™ HS2 Clear (optional
CLEAN UP: Clean up paint tools or spills immediately with for ultimate gloss and durability).
recommended thinner, carefully observing cautions on paint
and thinner labels. Dried paint may be removed by scraping. ALTERNATE PRIMERS: Contact JONES-BLAIR® Com-
pany.
ENGINEERED SYSTEMS
HEALTH AND SAFETY
SYSTEM - A
Read the Material Safety Data Sheet (MSDS) and container
For maximum corrosion resistance and durability. Recom- labels for detailed health and safety information. This product
mended for use in coastal and marine exposures above the is intended for industrial use by properly trained professional
splash zone over a sandblasted surface. applicators only.
The information, data and suggestions contained herein are believed to be reliable, based upon our knowledge and experience; however, it is expressly declared that Seller does not
guarantee the result to be obtained in Buyer’s process. SELLER HEREBY EXPRESSLY DISCLAIMS ANY IMPLIED WARRANTY OF MERCHANTABILITY FOR FITNESS FOR A
PARTICULAR PURPOSE AND/OR ANY OTHER WARRANTY, EXPRESS OR IMPLIED as to any and all products and/or suggestions described herein, whether such products are
used alone or in combination with other materials. Buyer must make its own determination of the suitability of any product for its use, and the completeness of any information contained
herein. Nothing contained herein shall be construed to constitute inducement or recommendation to practice any invention covered by any patent without authority from the owner of
the patent. 09192006 AcrylithaneHS2TD.indd
JONES-BLAIR®
2728 Empire Central - P.O. Box 35286 - Dallas, TX 75235 - Telephone (214) 353-1600 - Fax (214) 350-7624 - www.jones-blair.com