Professional Documents
Culture Documents
This is a 5V 2-Channel Relay interface board, Be able to control various appliances, and
other equipments with large current. It can be controlled directly by Micro-controller
(Arduino , 8051, AVR, PIC, DSP, ARM, ARM, MSP430, TTL logic) .
5V 2-Channel Relay interface board, and each one needs 15-20mA Driver Current
Equiped with high-current relay, AC250V 10A ; DC30V 10A
Standard interface that can be controlled directly by microcontroller (Arduino ,
8051, AVR, PIC, DSP, ARM, ARM, MSP430, TTL logic)
Indication LED’s for Relay output status
Dual H Bridge L298N for DC Stepper Motor Driver Module Controller
Introduction:
Using L298N as the control chip,the module has such characteristics as strong driving
ability,low calorific value and strong anti-interference ability
This module can use built-in 78M05 for electric work via a driving power supply part.
But to avoid the damage of the voltage stabilizing chip, please use an external 5V logic
supply when using more than 12V driving voltage
Using large capacity filter capacitor, this module can follow current to protect
diodes,and improve the reliability
Features:
Double H Bridge Motor Driver Module
Control Chip: L298N
Logical Voltage: 5V
Drive Voltage: 5V-35V
Logical Current: 0mA-36mA
Drive Current 2A(MAX single bridge)
Storage Temperature: -20 to +135
Max Power: 25W
Size: Approx. 43 x 43 x 27mm/ 1.69" x 1.69" x 1.07"
Receiver Module Link Kit + 433Mhz WL RF Transmitter Wireless MX-FS-
03V &MX-05
Features:
Features:
1-Channel relay module, with photoelectric isolation
The module can be high or low by a jumper setting trigger
With power and relay action indicator
The module Operating voltage 12V
The module uses genuine quality relay, normally open interfaces Maximum load: AC 250V/10A, For
DC 30V/10A
Size:44x 24x 17mm
Weight: 16g
Module interface:
For DC+: positive power supply (VCC)(12V)
For DC-: negative power supply (GND)
IN: The control end, the driving current should be more than 4mA
COM: The control of loop of earth wire
GND: Ground
NRF24L01 2.4GHz Wireless Transceiver Module
Features:
Features:
Mode of connection:
1.VCC
2.trig(T)
3.echo(R)
4.GND
Features:
1. Work under low static current
2. Power supply voltage: For DC2.5-12V
3. Each channel has 800mA continuous current output
4. Low saturation pressure drop
5. TTL/CMOS output level compatible, can be connected directly to the CPU
6. Output built-in clamping diode, apply to the perceptual load
7. Control and drive integrate in for IC
8. Pin high pressure for protection function
9. Working temperature: 0-80 ℃
10. Size:29*21mm (L*W)
High Sensitivity Control Potentiometer Sound Sensor Detection Module
Features:
Size: About 32mm x 17mm x 15mm
Main Chip: LM393, Electret condenser microphone
Signal output indication
Maximum induction distance is 0.5m
Operating Current Pressure: 4V-6V
The product boast of output signal instruction.
Single-channel signal output
Output valid signal is low and the light will be bright
Can be used for Acoustic control light; give sound and light alarm working with photosensitive
sensor
Specification:
Weight: 4g
Size: 3.1x1.6x0.8cm
5V 1 Channel Relay Module Board Shield
Features:
A 5V 1-Channel Relay
Can be used as single chip development module
5V-12V TTL control signal
Control direct current or AC signal
Can control 220V AC load
With power indicator
With control indicator
Increased transistor drive a relay coil, the control pin high impedanceThe control
pins have pull-down circuit, to prevent floating relay malfunction
This 5V Relay Module can be controlled directly by a wide range of microcontrollers
such as for Arduino, AVR, PIC and ARM,etc.
It can be used for home automation control
It is with 5V~12V TTL control signal which can control direct current/ AC signal. The
module is perfect for common for Arduino application
MQ-2 Gas Sensor Module Smoke Methane Butane Hydrogen Gas Detection
Introduce:
MQ-2 gas sensor sensitive material used in the clean air low conductivity tin oxide (SnO2).
When there is the environment in which the combustible gas sensor, conductivity sensor
with increasing concentration of combustible gases in air increases. Using a simple circuit
to convert the change in conductivity of the gas concentration corresponding to the output
signal. MQ-2 gas sensor high on gas, propane, hydrogen sensitivity of detection of natural
gas and other flammable vapors are also very good. This sensor can detect a variety of
flammable gas, is a low-cost sensors for a variety of applications.
Features:
Using high-quality dual-panel design, with power indicator and TTL signal output
instructions ;
The switching signal having a DO (TTL) output and analog output AO ;
TTL output valid signal is low . ( Low-level signal when the output light can be
directly connected to the microcontroller or relay module )
Analog output voltage with the higher concentration of higher voltage.
A gas, natural gas, city gas , smoke better sensitivity.
There are four screw holes for easy positioning ;
Product dimensions : 32 (L) * 20 (W) * 15 (H)
Has a long life and reliable stability
Rapid response and recovery characteristics
Chip: LM393, ZYMQ-2 gas sensors
Working voltage: for DC 5V
Detection of gas: combustible gases, fumes
Detectable concentration :300-10000ppm (flammable gas)
Soil Hygrometer Humidity Detection Module Soil Moisture Water Sensor
Features:
Specification:
Size: 3.7(L)x1.3(W)x1.2(H)cm
Weight: 10g
Dupont Length: 20cm
4 Bits Digital Tube LED Display Module Board With Clock Display
Features:
The module is a 10 foot with a clock point, with four common anode tube (0.36 inch)
display module for driver for IC 595, only two signal lines can make the MCU control 4 digit
7 segment digital tube.
It has 24 hour timing error correction settings, can set every 24 hours error correction,
setting range is -9 to 9 seconds. (Note: To make this effective, it must be 24 hours of
continuous power)
4 display modes: A. display time; B. display data; C. display temperature; D. alternate
display time, data and temperature
Specification:
Size: 42 x 24 x 12 mm
Temperature display range: -9 to 60°C
Temperature error correction setting feature, set the range: -5 to 5°C
Working voltage: 3.3V~5V. (Note: the lower the voltage, the lower the luminance, the lower
the power consumption)
Arduino UNO R3 Board ATMEGA328P
Mini USB 5V 1A Lithium Battery Charging Board Charger Module
Feature:
This Wireless Module is with Transmit Power amplifier and Receive Preamplifier.The 8
pins can connect to Arduino and the software can be used.
These transcevers use the 2.4 GHz unlicensed band like many WiFi routers, some
cordless phones etc.
Transceivers like these both send and receive data in 'packets' of several bytes at a
time. There is built-in error correction and resending, and it is possible to have one unit
communicate with up to 6 other similar units at the same time.
NRF24L01P + PA + LNA Division I for the ultra-long-distance data transmission
specially developed high-power and high sensitivity wireless module 2.4G ISM band
NRF24L01P + PA + LNA wireless module to work in the license-free, can be point-to-
pointapplications, can also be composed of a star network,
NRF24L01P + PA + LNA wireless module core Norway NORDIC company's latest high-
performance wireless
Digital transmission chip NRF24L01 +, with the Division of Professional Design
professional full two-way RF power amplifier high power PA and LNA chip, RF switches,
bandpass filters, etc., makes effective communication distance greatly expand.
RF part, the Secretary has done a lot of optimization matching debugging, the emission
efficiency to achieve the highest harmonic minimum
Makes NRF24L01P + PA + LNA wireless module of RF interference to the external
equipment reaches a minimum, while not susceptible to interference from other
devices, greatly Uploader
High stability of the work.
NRF24L01P + PA + LNA wireless module integration is extremely high, the size of only
41mm * 15.5mm, convenient embedded
In any tight space products, customers can increase an MCU through the SPI port to
control NRF24L01P + PA + LNA
Wireless module to complete the design of ultra-long-range wireless data transmission
system completely eliminates the need for the RF part of the R & D
Worry about slash R & D spending and shorten the development cycle
Arduino Servo Motor TowerPro SG92R Digital 2.5kg
/cm
Specification:
Weight: 11g
Dimension: 23×12.2x27mm
Stall torque: 2.5kg /cm(4.8v)
Gear type: Nylon with carbon fiber
Operating speed: 0.1sec /60degree (4.8v)
Operating voltage: 4.8v
Temperature range: 0c_ 55c
Dead band width:1us
servo wire length: 25 cm
Servo Plug: JR (Fits JR and so on)
servo arms &screws
It's universal “S" type connector that fits most receivers, including JR, Hitec ,GWS,
CE &RoHS approved
HC 06 RF Wireless Bluetooth Transceiver Module
RS232 / TTL / arduino
Using HC - 06 from module 1, a core module, which leads to the interface includes VCC, GND, TXD, RXD,
reserved LED state output pin, MCU can state whether the bluetooth is connected through the foot, from
machine KEY pin is invalid
2, the led indicates a bluetooth connection status, twinkle said there was no bluetooth connectivity, Chang
Liang said bluetooth is connected and turned on the port
3, backplane "3.3 V, the input voltage 3.6 ~ 6 V, current when the unpaired about 30 ma, matching after about
10 ma, no more than 7 V input voltage!
4, interface level 3.3 V, can be connected directly to all kinds of single chip microcomputer (51, AVR, PIC,
ARM, MSP430, etc.), 5 V single chip can be connected directly, without MAX232 couldn\'t through
MAX232.
5, clearing the effective distance of 10 meters, more than 10 meters is possible, but not to this distance
connection quality
After 6, pairing when full duplex serial port to use, do not need to know any bluetooth protocol, but supports
only one in the eight data bits, stop bits and parity checking the communication format, which is the most
commonly used communication format, does not support other formats.
7, when the bluetooth connection has not been established by pairing the AT command set baud rate, name,
password, and set the parameters of the power save. After the bluetooth connection automatically switch to
passthrough mode
8, small size (3.57 cm * 1.52 cm), SMT factory, ensure the quality of the patch. And set transparent heat
shrinkable tube, dust and beautiful, and there are some antistatic ability.
9, this link for the machine, from the function and all kinds of computer with bluetooth, bluetooth host, with
most of bluetooth mobile phone, PDA, PSP and other intelligent terminal pair, not matching between from the
machine
Allows your device to both send or receive the TTL data via Bluetooth technology without connecting a serial
cable to your computer. Just power, ground, rx, tx and you can send data to/from Arduino
Works with any USB Bluetooth adapters
Default Baud Rate: 9600,8,1,n default passcode: 1234
Built in antenna
Coverage up to 30ft
Specifications:
Bluetooth version: V2.0 + EDR
Operating voltage: 3.3V - 5 V
Default Baud Rate: 9600,8,1,n.
Signal coverage: 30ft
Item size: 4.3 x 1.6 x 0.7cm (board length 3.75cm)
Item weight: 3g
Solenoid Valve Magnetic N/C DC 24V Water Air
Inlet Switch / arduino
Material:Metal + plastic
Voltage:DC 24V
Inlet and outlet:hose barbs for 1/2" (outer diameter) hose
Pressure:0.02- 0.8Mpa
Max fluid temperature:100°C
Operation mode:normally closed
Valve type:diaphragm (operated by Servo)
Usage:water and low viscosity fluids
Please note it is not suitable for use with gravity fed systems
Product Dimension:78mm x 60mm(about)
The inner diameter:13.5mm
Four external diameter of thread:20mm
Water Flow Sensor Flowmeter 1-30L/min / arduino
debitmetru apa
Caracteristici:
Size:53mm x 35mm
Compatible with 5 V, 3.3 V,apply to MB102 breadboard
Input voltage: 6.5-12 V (DC) or USB power supply
Output voltage: 3.3V/5V can switch over
Max output current: <700 mA
Fluctuation two road independent control, can switch over to 0 V, 3.3 V, 5 V
On-board two groups of 3.3V, 5V DC output plug pin, convenient external
lead use