You are on page 1of 2

Ada beberapa factor untuk meningkatkan HSPA cell THP.

1. Carrier: missal ada 2 carrier yaitu F1 & F2. Ini dapat di setting F1 untuk all carrier
(voice,R99,HSDPA & HSUPA), sedangkan untuk F2 nya di gunnakan untuk service HSDPA &
HSUPA saja. Lesson learnednya berdasarkan pengalaman settingan seperti itu untuk mengurangi
handover antar carrier supaya meningkatkan hspa throughput
2. Pastikan transport tidak congest/bottleneck
3. Pastikan CE & Power Util juga tidak congest
4. Kurangi inter & IRAT HO: HO ini menggunakan metode CM (compress mode) yang berefek
kepada power. Semakin banyak bias kita kurangi konsumsi power, semakin baik HSDPA &
HSUPA throughput yg di hasilkan.
5. Kondisi RF: pastikan RF dalam kondisi yang ideal (interference kecil, no high rtwp, SINR baik)
6. PDSCH codes: maksimalkan 15 per cell
7. Hsdpa user: maksimalkan hsdpa usernya
8. Feature: 64 QAM, load baancing, 2MSTTI.

Sharing traffic 2G-3G

1. MIN_ECNO_THRESHOLD: default=-15 dB
With this parameter you define the minimum CPICH Ec/Io level of an adjacent WCDMA RAN cell
for an inter-system handover attempt. The threshold level must be exceeded before the BSC is
allowed to trigger a handover attempt towards the adjacent WCDMA RAN cell. The value 0.5 dB
of this parameter means that the BSC is never allowed to initiate a handover attempt from the
serving GSM cell towards the WCDMA RAN cell because a CPICH Ec/Io level measured by
mobiles can be maximum 0 dB. internal_value = (gui_value + 24) * 2
semakin kecil akan semakin cepat HO ke 3G
2. LOAD_THRESHOLD_FOR_SC_IS_HO: def = 80%
With this parameter you define the minimum traffic load that must be exceeded on the serving
GSM cell before the handover algorithm is allowed to initiate a handover for a speech call from
the serving GSM cell to a WCDMA RAN cell
semakin kecil akan semakin cepat HO ke 3G
3. MIN_INTERVAL_BETWEEN_UNSUCC_ISHO_ATTEMPT: def = 3s
With this parameter you define the minimum length of time interval between inter-system
handover attempts related to the same connection and the same non-GSM cell when a
handover attempt from the serving GSM cell to a non-GSM cell has been unsuccessful.
semakin kecil akan semakin cepat HO ke 3G
4. QSEARCH_C: def = 15
With this parameter you indicate a threshold for multi-RAT (radio access technology) MSs in
dedicated state to measure WCDMA RAN neighbour cells introduced in 3G Cell Reselection list
when the measured downlink signal level (RLA_C) of the serving cell is below (0-7) or above (8-
15) the threshold. NOTE: If the parameter value is 7 then dual mode GSM/WCDMA (multi-RAT)
MSs in dedicated state measure always neighbour WCDMA RAN cell(s). If the parameter value is
15 then dual mode GSM/WCDMA (multi-RAT) MSs in dedicated state do not measure any of the
neighbour WCDMA RAN cells.
Cell Reselection 3G -> 2G

UE starts GSM measurements if CPICH Ec/No < qQualMin + sSearchRAT => parameter di 3G
First ranking of all the cells based on CPICH RSCP (WCDMA) and RSSI (GSM)
Rs = CPICH RSCP + Qhyst1 => parameter di 3G
Rn= Rxlev(n) - Qoffset1 => parameter di 3G

You might also like