Professional Documents
Culture Documents
Uses Properties
To provide a durable, easily cleaned, high build coating in The values given below are average figures achieved in
o o
areas where a hard wearing, high resistance to chemical laboratory tests at 20 C and 35 C. Actual values obtained
attack is required. It is suitable for use in process plants, car on site may show minor variations from those quoted.
parks, battery rooms, school laboratories, sewage works, and o o
automobile workshops. Ambient Temperature @ 20 C @ 35 C
Pot life: 3 hours 1.5 hours
Tack free time: 6-8 hours 3-4 hours
Advantages
Time between coats: 12-24 hours 8-18 hours
Initial hardness: 30 hours 16 hours
Very hard wearing - durable, low maintenance costs, Full cure: 10 days 7 days
accepts vehicle traffic. Dry film thickness (2 coats): 300 microns (approx.)
High resistance to a wide range of industrial chemicals. Mixed Specific Gravity: 1.32 ± 0.05
Volume of Solids: 75%
Hygienic - impervious finish provides easily cleaned
surface. *Note that after the pot life has expired, the material,
although not hardened, increases in viscosity and the
Attractive - available in a range of colours to improve the characteristics of the product change. Excess material
working environment. should be discarded after this point.
Excellent adhesion to most substrates.
Chemical properties
Description
Nitoflor FC145 is resistant to a wide range of chemicals.
Nitoflor FC145 is a three-component (Base, Hardener, Color- Specific data is available on request.
pack) solvent based, epoxy resin coating system supplied in
pre-weighed packs ready to on-site mixing and use. Specification clauses
The cured film forms a hard, durable coating with excellent Epoxy coating
adhesion to clean concrete, sand/cement mortar, granolithic
screeds, and certain metal surfaces. It cures to a semi-gloss, The coating shall be Nitoflor FC145, a three-component,
impervious finish which is easily cleaned. high build, solvent based epoxy coating suitable for
application by brush or lambswool roller. The coating shall
The material has 7 standard colors: Brick-red, White, Sage be applied in 2 coats to achieve total dry film thickness of
Green, Off White, Buff, Silver Grey, Dark Grey. approximately 300 microns.
Page 1
Nitoflor FC145
Old concrete Estimating
The mixed Nitoflor FC145 should be applied to the prepared Storage conditions
surface using a brush or lambswool roller. Ensure that the
area is completely coated and that ‘ponding’ of the material The product should be stored in accordance with local
does not occur. The second coat may be applied as soon as ‘highly flammable liquids and liquefied petroleum gas
the first coat has initially dried (typically 12 to 18 hours). The regulations’.
time will be dependent on the type of surface and the
ambient conditions.
Precautions
Cleaning
Health and safety
Nitoflor FC145 should be removed from tools and equipment
with Fosroc Solvent 102 immediately after use. Hardened Nitoflor FC145, Nitoprime 31 and Fosroc Solvent 102
material can only be removed mechanically. should not come into contact with skin and eyes or be
swallowed. Ensure adequate ventilation and avoid
inhalation of vapours. Some people are sensitive to resins,
Limitations hardener and solvents. Wear suitable protective clothing,
gloves, and eye protection. If working in confined areas,
Nitoflor FC145 should not be applied onto surfaces known to suitable respiratory protective equipment must be used.
or likely to suffer from rising damp or have a relative humidity Use of barrier creams provides additional skin protection. In
greater than 75% as measured in accordance with BS 8202 case of contact with skin, rinse with plenty of clean water,
Appendix A or by a Vaisala thermo-hygrometer type HMI 31. then cleanse with soap and water.
Nitoflor FC145 should not be applied to asphalt floors or PVC Do not use solvent. In case of contact with eyes, rinse
tiles or sheet. immediately with plenty of clean water and seek medical
advice. If swallowed, seek medical attention immediately
Nitoflor FC145 should not be installed at temperatures below do not induce vomiting.
o
5 C.
Fire
Disposal
Additional information
Important note:
Fosroc products are guaranteed against defective materials and manufacture and are sold subject to its standard Conditions
for the Supply of Goods and Services, copies of which may be obtained on request. Whilst Fosroc endeavours to ensure that
any advice, recommendation, specification of information it may give is accurate and correct, it cannot, because it has no direct
or continuous control over where or how its products are applied, accept any liability either directly or indirectly arising from the
use of its products, whether or not in accordance with any advice, specification, recommendation of information given by it.
Registered Office: Industrial Area, Phase 4, Road No. 414, Street No. 407
Page 3 SA FO/NITOFLOR FC145/05/C