Professional Documents
Culture Documents
Uses
Page 1
Nitoflor TF5000
Chemical resistance Old concrete floors
Fully cured blocks of Nitoflor TF5000 have been tested in a Again mechanical cleaning methods are strongly
wide range of aggressive chemicals commonly found in recommended on old concrete floors particularly where
industrial environments. Tests were performed by constant heavy contamination by oil and grease has occurred or
o o
immersion at 20 C and 35 C. The blocks were visually existing coatings are present. This may well have been
inspected and tested for Shore ‘D’ hardness in accordance absorbed several mm into the concrete. To ensure
with ASTM D2240. adhesion all contamination should be removed. Chemical
Degreaser may be used on small areas of light
Acids contamination only.
Hydrochloric 50% Excellent All dust and debris should be removed prior to laying
Sulphuric 50% Excellent Nitoflor TF5000.
Phosphoric 50% Excellent
Nitric 25% Excellent Steel surface
Lactic 10% Excellent
Citric 10% Excellent Should be degreased and grit-blasted to Sa 2½ (BS4232
second quality) immediately prior to application).
Alkalies
Priming
Sodium Hydroxide 50% Excellent
Ammonia (880) 10% Excellent All surfaces treated with Nitoflor TF5000 should be primed
with Nitoprime Primer, a solvent free epoxy resin primer
Solvents / Organics designed for maximum absorption and adhesion to concrete
substrates. Add the entire contents of the smaller hardener
Butanol Good tin to the base tin and mix thoroughly. Once mixed
White Sprit Excellent immediately apply the primer in a thin continuous film to the
Oil / Grease / Petrol Excellent clean prepared surfaces. Work the primer into the surface
using stiff brushes, avoid over application and puddling. On
Xylene Excellent
porous floors the Nitoprime Primer will be absorbed very
Acetone Not resistant
quickly leaving, characteristic light coloured dry patches. It
Skydrol Good is recommended that a second priming coat is applied. This
Aqueous Solutions not only helps to ensure adhesion but prevents air release
from the porous substrate which may cause bubbles in the
final applied screed.
Conc. Bleach Excellent
Sat. Urea Excellent
Allow the primer to become tacky. This time is dependant
Sat. Sugar Excellent
on climatic conditions. See ‘Properties’ for ‘maximum
overlay times.
Those materials marked ‘Good’ are suitable for areas of
occasional spillage where good housekeeping is in force. Mixing
All the above properties have been determined by It is important that Nitoflor TF5000 is mixed correctly. The
laboratory controlled tests and are typical of those expected total contents of the aggregate bag should be emptied and
in practice. dry blended for 2 to 3 minutes in a suitable forced action
mixer such as Mixal, Cretangle or similar. A free fall mortar
Instruction for use mixer is not suitable.
Surface preparation The entire contents of the hardener can should then be
poured into the base container and mixed thoroughly until
It is essential that Nitoflor TF5000 is applied to sound, clean homogeneous.
and dry surface in order that maximum bond strength is
achieved between the substrate and the flooring system. Add the mixed base and hardener slowly to the aggregate.
Continue mechanical mixing for a further 2 to 3 minutes,
New concrete floors until all components are thoroughly blended. Once mixed,
the material must be used within the specified pot life (se
o
Should be at least 21 days old (at 20 C). Laitence deposits under ‘Properties’). After this time, unused material will
on new concrete floors are best removed by light grit- have stiffened and should be discarded.
blasting, mechanical scabbling or grinding. On smaller
areas thorough acid etching using Fosroc Acid Etch may be Application
considered. After etching the floor should be thoroughly
washed with clean water and then allowed to dry. The mixed Nitoflor TF5000 should be spread to uniform
thickness on the primed surface using either a garden
Important note:
Fosroc products are guaranteed against defective materials and manufacture and are sold subject to its standard Conditions
for the Supply of Goods and Services, copies of which may be obtained on request. Whilst Fosroc endeavours to ensure that
any advice, recommendation, specification of information it may give is accurate and correct, it cannot, because it has no direct
or continuous control over where or how its products are applied, accept any liability either directly or indirectly arising from the
use of its products, whether or not in accordance with any advice, specification, recommendation of information given by it.
Registered Office: Industrial Area, Phase 4, Road No. 414, Street No. 407
Page 3 SA FO/NITOFLOR TF5000/05/B