Professional Documents
Culture Documents
OF
POLLUTION CONTROL BORAD
PUNJAB
AT
CLIENT:
SUBMITTED BY:
EMAIL: dsindia1@gamil.com
SCOPE OF DESIGN REPORT
This design report consists of the details in respect of POLLUTION CONTROL BOARD
Seismic zone: IV
Structural configuration: RCC framed type construction for POLLUTION CONTROL BOARD.
Load of the walls has been transferred to column footings through plinth beams / plinth
bands.
NGL = 0.00
FGL = 0.00
FFL = 0.45m
DESIGN CODES AND REFERENCES
Page : 1
CONSISTENCY OF MODEL
Following snap shots of the model prove that the prepared model is consistent with
architectural and structural drgs.
Dimensions
Page : 2
Roof Plan
Terrace Plan
Mumty Plan
Page : 3
Story Data
Models have been checked for following warnings and there are no warning messages.
GRADE OF MATERIALS AND SIZES OF STRUCTURAL ELEMENTS
Page : 4
Concrete grade M25 is defined in ETABS. Snapshots of materials definitions are given
below:
Page : 5
LOADING DETAILS
ROOF (KN/m)
Page : 6
NALYSIS OF STRUCTURE
Static Load cases
Four Nos. static load cases have been defined. These are shown below in the snapshot
below.
Parameters for defining the earthquake loading are shown in the snapshot below.
Page : 7
Analysis options
Mass source Definition
Page : 8
Load Combinations
Page : 9
Combo Case Factor
DCON17 EQYN 1.5
DCON18 DEAD 1.5
DCON18 EQYN ‐1.5
DCON19 DEAD 0.9
DCON19 EQXP 1.5
DCON20 DEAD 0.9
DCON20 EQXP ‐1.5
DCON21 DEAD 0.9
DCON21 EQYP 1.5
DCON22 DEAD 0.9
DCON22 EQYP ‐1.5
DCON23 DEAD 0.9
DCON23 EQXN 1.5
DCON24 DEAD 0.9
DCON24 EQXN ‐1.5
DCON25 DEAD 0.9
DCON25 EQYN 1.5
DCON26 DEAD 0.9
DCON26 EQYN ‐1.5
DESIGN OF SLABS
An idea of sizes of slabs can be had from the section ‘Consistency of Model.
DESIGN OF FOUNDATIONS
Page : 10
REACTION NODES AND REACTIONS
Page : 11
Base 7 Dead 12.2053 ‐8.1954 400.385 3.70537 7.07131 0.00118
Page : 12
Base 11 EQXP ‐4.64107 ‐5.7E‐05 ‐0.36472 0.00141 ‐4.66542 0.0041
Page : 13
Base 15 EQXN ‐5.43556 0.00189 ‐0.36737 ‐0.00317 ‐5.1546 ‐0.01104
Page : 14
Base 20 Dead 9.15 ‐3.48 435.95 2.39 4.36 ‐0.02
Page : 15
Base 24 EQXP ‐4.89 0.00 ‐0.71 0.00 ‐4.90 0.01
Page : 16
Base 28 EQXN ‐3.01 0.00 0.56 0.00 ‐3.42 0.00
Page : 17
Base 34 Dead ‐6.22 2.70 580.53 ‐1.49 ‐3.00 0.03
Page : 18
Base 38 EQXP ‐3.95 0.00 0.00 0.00 ‐4.08 0.03
Point Load Case FZ MX MY Appx GR Max Pr Min Pr Permissible
Side
10 DL+LL 452.89 ‐1.6858 0.39817 2.04 TF4 104.10 101.76 120.00
Page : 19
10 DL+LL+EQXP 452.918 ‐1.6881 5.03047 1.82 TF4 106.72 99.15 150.00
10 DL+LL+EQYP 453.451 ‐6.7707 0.42406 1.82 TF4 107.11 99.00 150.00
10 DL+LL+EQXN 452.918 ‐1.6881 5.03047 1.82 TF4 106.72 99.15 150.00
10 DL+LL+EQYN 453.451 ‐6.7707 0.42406 1.82 TF4 107.11 99.00 150.00
11 DL+LL 449.95 ‐13.542 ‐1.3725 2.03 TF4 110.67 93.86 120.00
11 DL+LL+EQXP 450.315 ‐13.544 ‐6.0379 1.82 TF4 113.38 91.31 150.00
11 DL+LL+EQYP 450.146 ‐18.384 ‐1.4002 1.82 TF4 113.45 91.16 150.00
11 DL+LL+EQXN 450.315 ‐13.544 ‐6.0379 1.82 TF4 113.38 91.31 150.00
11 DL+LL+EQYN 450.146 ‐18.384 ‐1.4002 1.82 TF4 113.45 91.16 150.00
12 DL+LL 405.86 ‐4.1321 1.42097 1.93 TF4 95.37 89.11 120.00
12 DL+LL+EQXP 406.203 ‐4.1328 6.13843 1.73 TF4 98.11 86.53 150.00
12 DL+LL+EQYP 406.43 ‐9.8261 1.44937 1.73 TF4 98.72 86.02 150.00
12 DL+LL+EQXN 406.203 ‐4.1328 6.13843 1.73 TF4 98.11 86.53 150.00
12 DL+LL+EQYN 406.43 ‐9.8261 1.44937 1.73 TF4 98.72 86.02 150.00
13 DL+LL 392.404 ‐2.0665 ‐0.713 1.90 TF4 90.75 87.62 120.00
13 DL+LL+EQXP 392.415 ‐2.0671 ‐5.4036 1.70 TF4 93.39 84.98 150.00
13 DL+LL+EQYP 393.026 ‐7.2826 ‐0.7404 1.70 TF4 93.84 84.80 150.00
13 DL+LL+EQXN 392.415 ‐2.0671 ‐5.4036 1.70 TF4 93.39 84.98 150.00
13 DL+LL+EQYN 393.026 ‐7.2826 ‐0.7404 1.70 TF4 93.84 84.80 150.00
14 DL+LL 235.188 ‐3.0128 ‐0.7857 1.47 TF3 67.53 61.83 120.00
14 DL+LL+EQXP 235.225 ‐3.0143 ‐5.4919 1.31 TF3 71.07 58.31 150.00
14 DL+LL+EQYP 235.823 ‐8.414 ‐0.8128 1.32 TF3 71.77 57.93 150.00
14 DL+LL+EQXN 235.225 ‐3.0143 ‐5.4919 1.31 TF3 71.07 58.31 150.00
14 DL+LL+EQYN 235.823 ‐8.414 ‐0.8128 1.32 TF3 71.77 57.93 150.00
15 DL+LL 327.504 ‐2.65 2.92784 1.73 TF3 94.25 85.88 120.00
15 DL+LL+EQXP 327.872 ‐2.6532 8.08244 1.55 TF3 98.22 82.11 150.00
Page : 20
15 DL+LL+EQYP 328.122 ‐8.8657 2.96013 1.55 TF3 99.10 81.36 150.00
15 DL+LL+EQXN 327.872 ‐2.6532 8.08244 1.55 TF3 98.22 82.11 150.00
15 DL+LL+EQYN 328.122 ‐8.8657 2.96013 1.55 TF3 99.10 81.36 150.00
16 DL+LL 230.834 ‐3.4298 ‐8.7941 1.45 TF3 72.65 54.31 120.00
16 DL+LL+EQXP 231.755 ‐3.4335 ‐13.717 1.30 TF3 76.60 50.87 150.00
16 DL+LL+EQYP 231.459 ‐9.625 ‐8.8241 1.30 TF3 77.49 49.81 150.00
16 DL+LL+EQXN 231.755 ‐3.4335 ‐13.717 1.30 TF3 76.60 50.87 150.00
16 DL+LL+EQYN 231.459 ‐9.625 ‐8.8241 1.30 TF3 77.49 49.81 150.00
17 DL+LL 265.651 2.37358 ‐5.8156 1.56 TF3 79.20 66.91 120.00
17 DL+LL+EQXP 266.533 2.37885 ‐9.9075 1.40 TF3 82.51 64.08 150.00
17 DL+LL+EQYP 266.45 8.85774 ‐5.8239 1.40 TF3 84.28 62.26 150.00
17 DL+LL+EQXN 266.533 2.37885 ‐9.9075 1.40 TF3 82.51 64.08 150.00
17 DL+LL+EQYN 266.45 8.85774 ‐5.8239 1.40 TF3 84.28 62.26 150.00
18 DL+LL 266.901 ‐0.7171 ‐4.8238 1.56 TF3 77.55 69.24 120.00
18 DL+LL+EQXP 267.79 ‐0.7235 ‐9.1305 1.40 TF3 81.03 66.25 150.00
18 DL+LL+EQYP 267.701 ‐7.2015 ‐4.8307 1.40 TF3 82.64 64.59 150.00
18 DL+LL+EQXN 267.79 ‐0.7235 ‐9.1305 1.40 TF3 81.03 66.25 150.00
18 DL+LL+EQYN 267.701 ‐7.2015 ‐4.8307 1.40 TF3 82.64 64.59 150.00
19 DL+LL 231.302 5.02697 ‐8.9479 1.46 TF3 74.09 53.13 120.00
19 DL+LL+EQXP 232.223 5.03344 ‐13.948 1.30 TF3 78.10 49.63 150.00
19 DL+LL+EQYP 231.928 11.2221 ‐8.9771 1.30 TF3 78.93 48.63 150.00
19 DL+LL+EQXN 232.223 5.03344 ‐13.948 1.30 TF3 78.10 49.63 150.00
19 DL+LL+EQYN 231.928 11.2221 ‐8.9771 1.30 TF3 78.93 48.63 150.00
20 DL+LL 488.344 2.29771 3.2335 2.12 TF4 114.10 107.87 120.00
20 DL+LL+EQXP 488.706 2.30021 8.47617 1.89 TF4 117.14 105.00 150.00
20 DL+LL+EQYP 488.979 8.51366 3.26479 1.89 TF4 117.77 104.49 150.00
Page : 21
20 DL+LL+EQXN 488.706 2.30021 8.47617 1.89 TF4 117.14 105.00 150.00
20 DL+LL+EQYN 488.979 8.51366 3.26479 1.89 TF4 117.77 104.49 150.00
21 DL+LL 476.632 1.85733 ‐0.9313 2.09 TF4 109.90 106.75 120.00
21 DL+LL+EQXP 476.67 1.85921 ‐5.7431 1.87 TF4 112.62 104.05 150.00
21 DL+LL+EQYP 477.261 7.25928 ‐0.9579 1.87 TF4 113.10 103.84 150.00
21 DL+LL+EQXN 476.67 1.85921 ‐5.7431 1.87 TF4 112.62 104.05 150.00
21 DL+LL+EQYN 477.261 7.25928 ‐0.9579 1.87 TF4 113.10 103.84 150.00
22 DL+LL 449.748 2.63154 ‐0.5809 2.03 TF4 104.03 100.41 120.00
22 DL+LL+EQXP 449.766 2.6322 ‐5.4108 1.82 TF4 106.75 97.69 150.00
22 DL+LL+EQYP 450.38 7.88354 ‐0.6079 1.82 TF4 107.14 97.57 150.00
22 DL+LL+EQXN 449.766 2.6322 ‐5.4108 1.82 TF4 106.75 97.69 150.00
22 DL+LL+EQYN 450.38 7.88354 ‐0.6079 1.82 TF4 107.14 97.57 150.00
23 DL+LL 552.016 3.9586 1.92333 2.25 TF5 99.41 94.90 120.00
23 DL+LL+EQXP 552.728 3.96241 6.82013 2.01 TF5 101.42 93.14 150.00
23 DL+LL+EQYP 553.278 9.82776 1.95151 2.01 TF5 101.90 92.85 150.00
23 DL+LL+EQXN 552.728 3.96241 6.82013 2.01 TF5 101.42 93.14 150.00
23 DL+LL+EQYN 553.278 9.82776 1.95151 2.01 TF5 101.90 92.85 150.00
24 DL+LL 548.282 10.0673 ‐1.4508 2.24 TF5 100.92 92.07 120.00
24 DL+LL+EQXP 548.992 10.0695 ‐6.3539 2.01 TF5 102.93 90.32 150.00
24 DL+LL+EQYP 549.463 16.4065 ‐1.4786 2.01 TF5 103.57 89.84 150.00
24 DL+LL+EQXN 548.992 10.0695 ‐6.3539 2.01 TF5 102.93 90.32 150.00
24 DL+LL+EQYN 549.463 16.4065 ‐1.4786 2.01 TF5 103.57 89.84 150.00
25 DL+LL 391.614 2.50178 0.89702 1.89 TF4 90.92 87.09 120.00
25 DL+LL+EQXP 391.67 2.5038 5.72169 1.69 TF4 93.65 84.38 150.00
25 DL+LL+EQYP 392.192 7.63795 0.92397 1.70 TF4 93.96 84.31 150.00
25 DL+LL+EQXN 391.67 2.5038 5.72169 1.69 TF4 93.65 84.38 150.00
Page : 22
25 DL+LL+EQYN 392.192 7.63795 0.92397 1.70 TF4 93.96 84.31 150.00
26 DL+LL 570.912 2.08343 ‐4.6285 2.29 TF5 103.06 97.90 120.00
26 DL+LL+EQXP 571.277 2.08468 ‐9.8848 2.05 TF5 105.14 95.95 150.00
26 DL+LL+EQYP 571.443 8.06562 ‐4.6588 2.05 TF5 105.46 95.69 150.00
26 DL+LL+EQXN 571.277 2.08468 ‐9.8848 2.05 TF5 105.14 95.95 150.00
26 DL+LL+EQYN 571.443 8.06562 ‐4.6588 2.05 TF5 105.46 95.69 150.00
27 DL+LL 293.394 2.12575 0.8687 1.64 TF3 82.93 78.44 120.00
27 DL+LL+EQXP 293.638 2.12756 4.95797 1.47 TF3 86.06 75.44 150.00
27 DL+LL+EQYP 294.101 8.19442 0.87747 1.47 TF3 87.68 74.07 150.00
27 DL+LL+EQXN 293.638 2.12756 4.95797 1.47 TF3 86.06 75.44 150.00
27 DL+LL+EQYN 294.101 8.19442 0.87747 1.47 TF3 87.68 74.07 150.00
28 DL+LL 233.141 2.26346 ‐1.2267 1.46 TF3 66.73 61.50 120.00
28 DL+LL+EQXP 233.703 2.26596 ‐4.6426 1.31 TF3 69.45 59.09 150.00
28 DL+LL+EQYP 233.869 7.40472 ‐1.2332 1.31 TF3 70.79 57.84 150.00
28 DL+LL+EQXN 233.703 2.26596 ‐4.6426 1.31 TF3 69.45 59.09 150.00
28 DL+LL+EQYN 233.869 7.40472 ‐1.2332 1.31 TF3 70.79 57.84 150.00
30 DL+LL 438.845 4.26259 ‐1.1761 2.01 TF4 102.80 96.67 120.00
30 DL+LL+EQXP 439.388 4.2629 ‐4.5431 1.80 TF4 104.82 94.90 150.00
30 DL+LL+EQYP 439.669 10.1044 ‐1.1818 1.80 TF4 106.28 93.57 150.00
30 DL+LL+EQXN 439.388 4.2629 ‐4.5431 1.80 TF4 104.82 94.90 150.00
30 DL+LL+EQYN 439.669 10.1044 ‐1.1818 1.80 TF4 106.28 93.57 150.00
Page : 23
31 DL+LL 441.122 1.10773 ‐0.8155 2.01 TF4 101.34 99.17 120.00
31 DL+LL+EQXP 441.155 1.10856 ‐4.4761 1.80 TF4 103.41 97.12 150.00
31 DL+LL+EQYP 441.897 6.39282 ‐0.8226 1.80 TF4 104.50 96.37 150.00
31 DL+LL+EQXN 441.155 1.10856 ‐4.4761 1.80 TF4 103.41 97.12 150.00
31 DL+LL+EQYN 441.897 6.39282 ‐0.8226 1.80 TF4 104.50 96.37 150.00
32 DL+LL 405.94 ‐0.2655 ‐2.4747 1.93 TF4 93.80 90.71 120.00
32 DL+LL+EQXP 405.976 ‐0.2674 ‐6.2054 1.73 TF4 95.91 88.62 150.00
32 DL+LL+EQYP 406.734 ‐5.7828 ‐2.4821 1.73 TF4 97.10 87.78 150.00
32 DL+LL+EQXN 405.976 ‐0.2674 ‐6.2054 1.73 TF4 95.91 88.62 150.00
32 DL+LL+EQYN 406.734 ‐5.7828 ‐2.4821 1.73 TF4 97.10 87.78 150.00
33 DL+LL 439.838 0.33108 ‐1.5667 2.01 TF4 101.03 98.89 120.00
33 DL+LL+EQXP 440.154 0.33415 ‐5.7723 1.80 TF4 103.48 96.59 150.00
33 DL+LL+EQYP 440.668 6.6483 ‐1.5756 1.80 TF4 104.79 95.52 150.00
33 DL+LL+EQXN 440.154 0.33415 ‐5.7723 1.80 TF4 103.48 96.59 150.00
33 DL+LL+EQYN 440.668 6.6483 ‐1.5756 1.80 TF4 104.79 95.52 150.00
34 DL+LL 695.572 ‐0.6945 ‐1.6167 2.53 TF6 98.22 96.96 120.00
34 DL+LL+EQXP 695.869 ‐0.6967 ‐5.9988 2.26 TF6 99.46 95.80 150.00
34 DL+LL+EQYP 696.271 ‐6.7618 ‐1.6228 2.26 TF6 99.98 95.40 150.00
34 DL+LL+EQXN 695.869 ‐0.6967 ‐5.9988 2.26 TF6 99.46 95.80 150.00
34 DL+LL+EQYN 696.271 ‐6.7618 ‐1.6228 2.26 TF6 99.98 95.40 150.00
35 DL+LL 497.32 ‐0.3877 0.18779 2.14 TF4 113.35 112.70 120.00
35 DL+LL+EQXP 497.338 ‐0.3902 4.22358 1.91 TF4 115.63 110.43 150.00
35 DL+LL+EQYP 498.024 ‐5.5829 0.19268 1.91 TF4 116.44 109.93 150.00
35 DL+LL+EQXN 497.338 ‐0.3902 4.22358 1.91 TF4 115.63 110.43 150.00
35 DL+LL+EQYN 498.024 ‐5.5829 0.19268 1.91 TF4 116.44 109.93 150.00
36 DL+LL 706.968 4.45846 1.89083 2.55 TF6 100.93 97.46 120.00
Page : 24
36 DL+LL+EQXP 707.373 4.45961 6.09361 2.28 TF6 102.13 96.36 150.00
36 DL+LL+EQYP 707.899 10.7795 1.89633 2.28 TF6 102.79 95.86 150.00
36 DL+LL+EQXN 707.373 4.45961 6.09361 2.28 TF6 102.13 96.36 150.00
36 DL+LL+EQYN 707.899 10.7795 1.89633 2.28 TF6 102.79 95.86 150.00
37 DL+LL 545.699 ‐1.6215 ‐1.7842 2.24 TF5 97.35 94.74 120.00
37 DL+LL+EQXP 546.057 ‐1.6237 ‐5.9881 2.00 TF5 99.03 93.18 150.00
37 DL+LL+EQYP 545.78 ‐7.5857 ‐1.7904 2.00 TF5 99.66 92.46 150.00
37 DL+LL+EQXN 546.057 ‐1.6237 ‐5.9881 2.00 TF5 99.03 93.18 150.00
37 DL+LL+EQYN 545.78 ‐7.5857 ‐1.7904 2.00 TF5 99.66 92.46 150.00
38 DL+LL 443.384 ‐1.6491 ‐0.6444 2.02 TF4 102.06 99.48 120.00
38 DL+LL+EQXP 443.385 ‐1.65 ‐4.725 1.80 TF4 104.36 97.18 150.00
38 DL+LL+EQYP 444.152 ‐6.9814 ‐0.6508 1.80 TF4 105.24 96.64 150.00
38 DL+LL+EQXN 443.385 ‐1.65 ‐4.725 1.80 TF4 104.36 97.18 150.00
38 DL+LL+EQYN 444.152 ‐6.9814 ‐0.6508 1.80 TF4 105.24 96.64 150.00
39 DL+LL 481.677 ‐2.3876 ‐1.1064 2.10 TF4 111.44 107.50 120.00
39 DL+LL+EQXP 481.717 ‐2.3897 ‐5.1496 1.88 TF4 113.73 105.23 150.00
39 DL+LL+EQYP 482.476 ‐7.91 ‐1.1127 1.88 TF4 114.74 104.57 150.00
39 DL+LL+EQXN 481.717 ‐2.3897 ‐5.1496 1.88 TF4 113.73 105.23 150.00
39 DL+LL+EQYN 482.476 ‐7.91 ‐1.1127 1.88 TF4 114.74 104.57 150.00
40 DL+LL 525.779 ‐1.4319 ‐0.7083 2.20 TF5 93.36 91.72 120.00
40 DL+LL+EQXP 526.101 ‐1.4348 ‐5.1625 1.96 TF5 95.13 90.06 150.00
40 DL+LL+EQYP 526.593 ‐7.7523 ‐0.7157 1.97 TF5 95.93 89.43 150.00
40 DL+LL+EQXN 526.101 ‐1.4348 ‐5.1625 1.96 TF5 95.13 90.06 150.00
40 DL+LL+EQYN 526.593 ‐7.7523 ‐0.7157 1.97 TF5 95.93 89.43 150.00
Page : 25
5 DL+LL+EQYP 441.148 9.39654 9.87526 1.80 TF4 111.12 89.40 150.00
Page : 26
SBC = 120 kN/sqm Inc for EQ / Wind = 25%
DESIGN OF BEAMS AND COLUMNS
Structural design of beams and columns is carried out by ETABS using the following design
parameters.
Definitions of column and beam sections have been given in section ‘Consistency of Model’.
Page : 27
Page : 28
Page : 29
Story ColLine SecID StnLoc DesignOpt Status PMMCombo AsMin As
Page : 30
FF C11 C3046 1375 Design No Message DCon26 1104 1104
Page : 31
PL C13 C3046 1350 Design No Message DCon26 1104 1104
Page : 32
PL C15 C3046 1350 Design No Message DCon26 1104 1104
Page : 33
FF C18 C3046 0 Design No Message DCon2 1104 2463
Page : 34
PL C2 C3046 600 Design No Message DCon26 1104 1104
Page : 35
FF C22 C3046 2750 Design No Message DCon26 1104 1104
Page : 36
ROOF C26 C3046 1375 Design No Message DCon26 1104 1104
Page : 37
PL C29 C3046 0 Design No Message DCon26 1104 1104
Page : 38
FF C32 C3046 1375 Design No Message DCon26 1104 1104
Page : 39
PL C36 C3046 675 Design No Message DCon26 1104 1104
Page : 40
PL C4 C3046 0 Design No Message DCon26 1104 1104
Page : 41
ROOF C45 C3046 1150 Design No Message DCon26 1104 1104
Page : 42
PL C7 C3046 675 Design No Message DCon26 1104 1104
Page : 43
ColLine SecID StnLoc DesignOpt Status PMMCombo AsMin As
Page : 44
C32 C3046 2750 Design No Message DCon2 1104 2584
Page : 45
C15 C3046 0 Design No Message DCon26 1104 1104
Page : 46
C39 C3046 0 Design No Message DCon26 1104 1104
Page : 47
C15 24 C3046 1104 1104 C1 8 16 ‐ ‐ 1,608
C17 26 C3046 1104 2027 C2 4 20 + 4 16 2,061 1.49%
Page : 48
C33 17 C3046 1104 2134 C3 8 20 ‐ ‐ 2,513 1.82%
Page : 49
APPENDICES
Page : 50
DESIGN OF BI-AXIAL ISOLATED RCC FOOTING (IS 456, 2000)
LOADS (WORKING)
(DL+LL) (DL+EQXP) (DL+EQYP) (DL+EQXN) (DL+EQYN)
Axial load from output (Pu) = 119.70 120.13 120.31 120.13 120.31 KN
Moment about X axis (Mx) = 1.44 1.44 3.02 1.44 3.02 KN-m
Moment about Y axis (My) = 10.05 13.07 10.08 13.07 10.08 KN-m
FOOTING
Foot X-X (L, dim. || X axis) = 1.5 m
Foot Y-Y (B, dim. || Y axis) = 1.5 m
Thickness of footing (D) = 250 mm global
Thickness of footing at edge(t) = 150 mm Y-Y = 1.5 m Y
l
Clear cover of footing = 50 mm
Main bar dia of footing = 10 mm
Effective depth of footing (d)= 195 mm global
Effective thickness at edge(ti) = 95 mm b X
Extra-selfweight of the footing = 3.94 KN l
Area of Footing(A) = 2.25 m2
Sect mod of foot about X axis (Zx) = 0.56 m3 X-X = 1.5 m
3
Sec mod of foot about Y axis (Zy) = 0.56 m
Page : 51
2
Mu about X X = ( pe max x length /2)= 32.07 KN-m The section is singly reinforced
Mean depth parallel to X X = {l*d+[(L-l)*(d+ti)/2]/L} = 160.3 mm
2
Calc. Ast = 479.2 mm
2
Min Ast = 288.6 mm (0.12 % for slab, cl 26.5.2.1)
Dia Provided = 10 mm
Spacing required = 246 mm (considering max of above two calculated values of Ast)
Spacing provided = 150 mm pt provided = 0.327 %
Hence provide 10 mm dia bar @ 150 mm c/c parellel to breadth of footing ( || to Y)
Page : 52
DESIGN OF BI-AXIAL ISOLATED RCC FOOTING (IS 456, 2000)
LOADS (WORKING)
(DL+LL) (DL+EQXP) (DL+EQYP) (DL+EQXN) (DL+EQYN)
Axial load from output (Pu) = 327.50 327.87 328.12 327.87 328.12 KN
Moment about X axis (Mx) = 2.65 2.65 8.87 2.65 8.87 KN-m
Moment about Y axis (My) = 2.93 8.08 2.96 8.08 2.96 KN-m
FOOTING
Foot X-X (L, dim. || X axis) = 2.0 m
Foot Y-Y (B, dim. || Y axis) = 2.0 m
Thickness of footing (D) = 350 mm global
Thickness of footing at edge(t) = 200 mm Y-Y = 2 m Y
l
Clear cover of footing = 50 mm
Main bar dia of footing = 12 mm
Effective depth of footing (d)= 294 mm global
Effective thickness at edge(ti) = 144 mm b X
Extra-selfweight of the footing = 9.80 KN l
Area of Footing(A) = 4.00 m2
Sect mod of foot about X axis (Zx) = 1.33 m3 X-X = 2 m
3
Sec mod of foot about Y axis (Zy) = 1.33 m
Page : 53
2
Mu about X X = ( pe max x length /2)= 80.84 KN-m The section is singly reinforced
Mean depth parallel to X X = {l*d+[(L-l)*(d+ti)/2]/L} = 230.3 mm
2
Calc. Ast = 838.0 mm
2
Min Ast = 552.6 mm (0.12 % for slab, cl 26.5.2.1)
Dia Provided = 12 mm
Spacing required = 270 mm (considering max of above two calculated values of Ast)
Spacing provided = 150 mm pt provided = 0.327 %
Hence provide 12 mm dia bar @ 150 mm c/c parellel to breadth of footing ( || to Y)
Page : 54
DESIGN OF BI-AXIAL ISOLATED RCC FOOTING (IS 456, 2000)
LOADS (WORKING)
(DL+LL) (DL+EQXP) (DL+EQYP) (DL+EQXN) (DL+EQYN)
Axial load from output (Pu) = 501.85 502.46 502.50 502.46 502.50 KN
Moment about X axis (Mx) = 4.45 4.47 10.11 4.47 10.11 KN-m
Moment about Y axis (My) = 5.61 9.78 5.62 9.78 5.62 KN-m
FOOTING
Foot X-X (L, dim. || X axis) = 2.2 m
Foot Y-Y (B, dim. || Y axis) = 2.2 m
Thickness of footing (D) = 400 mm global
Thickness of footing at edge(t) = 200 mm Y-Y = 2.2 m Y
l
Clear cover of footing = 50 mm
Main bar dia of footing = 12 mm
Effective depth of footing (d)= 344 mm global
Effective thickness at edge(ti) = 144 mm b X
Extra-selfweight of the footing = 13.55 KN l
Area of Footing(A) = 4.84 m2
Sect mod of foot about X axis (Zx) = 1.77 m3 X-X = 2.2 m
3
Sec mod of foot about Y axis (Zy) = 1.77 m
Page : 55
2
Mu about X X = ( pe max x length /2)= 140.73 KN-m The section is singly reinforced
Mean depth parallel to X X = {l*d+[(L-l)*(d+ti)/2]/L} = 257.6 mm
2
Calc. Ast = 1317.6 mm
2
Min Ast = 680.16 mm (0.12 % for slab, cl 26.5.2.1)
Dia Provided = 12 mm
Spacing required = 189 mm (considering max of above two calculated values of Ast)
Spacing provided = 150 mm pt provided = 0.293 %
Hence provide 12 mm dia bar @ 150 mm c/c parellel to breadth of footing ( || to Y)
Page : 56
DESIGN OF BI-AXIAL ISOLATED RCC FOOTING (IS 456, 2000)
LOADS (WORKING)
(DL+LL) (DL+EQXP) (DL+EQYP) (DL+EQXN) (DL+EQYN)
Axial load from output (Pu) = 598.93 599.28 599.45 599.28 599.45 KN
Moment about X axis (Mx) = 2.00 2.00 7.98 2.00 7.98 KN-m
Moment about Y axis (My) = 4.63 9.73 4.66 9.73 4.66 KN-m
FOOTING
Foot X-X (L, dim. || X axis) = 2.5 m
Foot Y-Y (B, dim. || Y axis) = 2.5 m
Thickness of footing (D) = 400 mm global
Thickness of footing at edge(t) = 200 mm Y-Y = 2.5 m Y
l
Clear cover of footing = 50 mm
Main bar dia of footing = 16 mm
Effective depth of footing (d)= 342 mm global
Effective thickness at edge(ti) = 142 mm b X
Extra-selfweight of the footing = 17.50 KN l
Area of Footing(A) = 6.25 m2
Sect mod of foot about X axis (Zx) = 2.60 m3 X-X = 2.5 m
3
Sec mod of foot about Y axis (Zy) = 2.60 m
Page : 57
2
Mu about X X = ( pe max x length /2)= 196.57 KN-m The section is singly reinforced
Mean depth parallel to X X = {l*d+[(L-l)*(d+ti)/2]/L} = 254.0 mm
2
Calc. Ast = 1892.8 mm
2
Min Ast = 762 mm (0.12 % for slab, cl 26.5.2.1)
Dia Provided = 16 mm
Spacing required = 266 mm (considering max of above two calculated values of Ast)
Spacing provided = 175 mm pt provided = 0.452 %
Hence provide 16 mm dia bar @ 175 mm c/c parellel to breadth of footing ( || to Y)
Page : 58
DESIGN OF BI-AXIAL ISOLATED RCC FOOTING (IS 456, 2000)
LOADS (WORKING)
(DL+LL) (DL+EQXP) (DL+EQYP) (DL+EQXN) (DL+EQYN)
Axial load from output (Pu) = 706.97 707.37 707.90 707.37 707.90 KN
Moment about X axis (Mx) = 4.46 4.46 10.78 4.46 10.78 KN-m
Moment about Y axis (My) = 1.89 6.09 1.90 6.09 1.90 KN-m
FOOTING
Foot X-X (L, dim. || X axis) = 2.8 m
Foot Y-Y (B, dim. || Y axis) = 2.8 m
Thickness of footing (D) = 450 mm global
Thickness of footing at edge(t) = 200 mm Y-Y = 2.8 m Y
l
Clear cover of footing = 50 mm
Main bar dia of footing = 16 mm
Effective depth of footing (d)= 392 mm global
Effective thickness at edge(ti) = 142 mm b X
Extra-selfweight of the footing = 24.70 KN l
Area of Footing(A) = 7.84 m2
Sect mod of foot about X axis (Zx) = 3.66 m3 X-X = 2.8 m
3
Sec mod of foot about Y axis (Zy) = 3.66 m
Page : 59
2
Mu about X X = ( pe max x length /2)= 269.52 KN-m The section is singly reinforced
Mean depth parallel to X X = {l*d+[(L-l)*(d+ti)/2]/L} = 280.4 mm
2
Calc. Ast = 2351.7 mm
2
Min Ast = 942.12 mm (0.12 % for slab, cl 26.5.2.1)
Dia Provided = 16 mm
Spacing required = 239 mm (considering max of above two calculated values of Ast)
Spacing provided = 175 mm pt provided = 0.410 %
Hence provide 16 mm dia bar @ 175 mm c/c parellel to breadth of footing ( || to Y)
Page : 60
Job No.:
Project: Pollution Control Board, Punjab,Batala Design by:
Date: 16-Jun-16
Building: Pollution Control Board Page No. 1
Calculates Bending Moments as per Table 12 (Ref.: Cl. 22.5.1) of IS:456-2000, and Reinforcement for different
slab span, thickness and loads, for the given Concrete grade and type of Steel. Deflection check is made.
Concrete Grade = M 3
Yield Strength of steel, fy = 4 N/mm2
Clear cover to Reinforcement = 25 mm
RCDesignCD
Page : 61
Job No.: 0
Project: Pollution Control Board, Punjab,Batala Design by: 0
Date: 16-Jun-16
Building: Pollution Control Board Page No. 2
RCDesignCD
Page : 62
Job No.: 0
Project: Pollution Control Board, Punjab,Batala Design by: 0
Date: 16-Jun-16
Building: Pollution Control Board Page No. 3
RCDesignCD
Page : 63
Job No.:
Project: Pollution Control Board, Punjab,Batala Design by:
Date: 16-Jun-16
Building: Pollution Control Board Page No. 1
RCDesignCD
Concrete Grade = M 3
Yield Strength of steel, fy = 4 N/mm2
Clear cover to Reinforcement = 25 mm
Design of Two-way Restrained Slabs Types 1 to 9 Spans O/A thk Working load
Slab Mk. Panel Type Description lx (m) ly (m) 'D' (mm) Live (kN/m2)
S1 4 Toilet and guest room 4.27 6.02 150 4.00
S2 2 Guest room 3.96 4.27 150 4.00
S4 1 Corridor 2.59 3.96 150 4.00
S5 4 Terrace 4.27 6.02 150 1.50
S6 2 Terrace 3.96 4.27 150 1.50
S8 1 Terrace/Corridor 3.96 4.27 150 1.50
S9 9 Mumty 3.05 4.27 150 1.50
Page : 64
Job No.: 0
Project: Pollution Control Board, Punjab,Batala Design by: 0
Date: 16-Jun-16
Building: Pollution Control Board Page No. 2
RCDesignCD
Page : 65
Job No.: 0
Project: Pollution Control Board, Punjab,Batala Design by: 0
Date: 16-Jun-16
Building: Pollution Control Board Page No. 3
RCDesignCD
Reinforcement Calculation - Short Span
Steel at bottom Steel at top
Slab Mk.
Eff. 'd' Reqd.Ast(mm2) (mm2) Provide Ast Eff. 'd' Reqd.Ast Provide Ast
S1 120 285.62 320 00-000+10-125 120 389.70 00-000+10-125
S2 121 180.00 200 00-000+08-150 121 187.33 00-000+08-150
S4 121 180.00 200 00-000+08-150 121 180.00 00-000+08-150
S5 120 301.35 330 00-000+10-125 120 411.65 00-000+10-125
S6 121 180.00 200 00-000+08-150 121 197.27 00-000+08-150
S8 121 180.00 200 00-000+08-150 121 180.00 00-000+08-150
S9 121 211.16 200 00-000+08-150 121 0.00 00-000+08-150
0 - - - - -
0 - - - - -
0 - - - - -
Reinforcement Calculation - Long Span
Steel at bottom Steel at top
Slab Mk.
Eff. 'd' Reqd.Ast(mm2) Provide Ast Eff. 'd' Reqd.Ast(mm2) Provide Ast
S1 111 200.24 00-000+08-150 111 272.58 00-000+08-150
S2 113 180.00 00-000+08-150 113 180.00 00-000+08-150
S4 113 180.00 00-000+08-150 113 180.00 00-000+08-150
S5 111 211.24 00-000+08-150 111 287.79 00-000+08-150
S6 113 180.00 00-000+08-150 113 187.92 00-000+08-150
S8 113 180.00 00-000+08-150 113 180.00 00-000+08-150
S9 113 180.00 00-000+08-150 113 0.00 00-000+08-150
0 - - - -
0 - - - -
0 - - - -
Check on Deflection (Ref.: Clauses 23.2.1 and 24.1 of IS:456-2000)
Reqd. Short Span Btm Ast(mm2) Percentage Modifcn. Actual
Slab Mk. Span of Tension Factor Span Final Status
Reqd. Provided
Eff. d or D Reinf't (MF) (Eff.d or D x MF)
S1 26.0 285.62 320.6 0.2671 1.43125 24.8443 O.K.
S2 26.0 180.00 200.1 0.1653 1.73416 18.8816 O.K.
S4 26.0 180.00 200.1 0.1653 1.73416 12.3479 O.K.
S5 26.0 301.35 330.7 0.2756 1.37725 25.8365 O.K.
S6 26.0 180.00 200.1 0.1653 1.73416 18.8816 O.K.
S8 26.0 180.00 200.1 0.1653 1.73416 18.8816 O.K.
S9 20.0 211.16 200.1 0.1653 1.38487 18.2014 O.K.
0 - - - - - - -
0 - - - - - - -
0 - - - - - - -
Page : 66