Professional Documents
Culture Documents
Copyright
py g © 2012 byy “Sarzamin khan as jjamajhon j ((my
y nick name on
Alcatelunleashed.com)”. All rights reserved. This document may not be
reproduced in whole or in part without the express written permission from
“Sarzamin khan as jamajhon and my team. The informations given in this
document is not authorized to transmit or receive via any medium.
medium
Usage instruction:
The informations given below will only be used in presence of any qualified
Engineer or Technician and only will be used for training purpose. Do not try on live
Call Server CPU it may harm single CPU or whole network and may cause serious
damage to Call Server CPU hard disk . Please read carefully the instructions given
below do not by pass any step.
below, step Please make backup of your important data,
data The
author will not be responsible for any loss and corruption of data.
Please note that before starting installation of Release on Appliance Server you should
h
have f ll i
following software.
ft
(1) Named Pipe TCP Proxy
(2) Telnet application like Secure CRT, Putty or windows Ms-Dos Command Prompt
(3) VMware workstation 8.0
(4) OmniPCX Enterprise PC Installer tool
(5) FTP software like Total commander, File Zila or Smart FTP
R9.0 Installation procedure on Appliance Server
Note:
Before
e o e sta
starting
t g installation
sta at o you mustust have
a eO OPS So
on you
your PCC hard
a dd drive.
e
•Copy “dhs3mgr” release folder to hard drive ‘C’. It must have three sub folders i-e (i)
h1301 (ii) h130126 and (iii) h130126a
•Double click “OmniPCX Enterprise PC Installer” icon to open it. After this apply
following settings in “OmniPCX Enterprise PC Installer” tool
tool.
•Installation type=> Linux + Call handling
•Call server type => Appliance Server (See figures below)
•Call handling g version => h1301
•Country => pk (yours country)
•Installation type => Standard
•Network type => Direct cable
•Network interface => 172.26.66.27
172 26 66 27 (This IP address will be automatically detected by
“OmniPCX Enterprise PC Installer” tool from your PC LAN card.) After all above
settings click on Apply button to validate settings.
Select
“Appliance
Server”
Select
“h1301”
Select
“Country”
Select
“Standard”
Select
“Direct cable”
Select
“Your LAN card”
Select
“This
This IP address
will be
automatically
assigned to
Appliance server
”
Double click “Named Pipe TCP Proxy” to open it, Configure different parameters as given below.
¾ Click
Cli k on Edit and d again
i click
li k on N
New.
¾ Declare pipe name as “\\. \pipe\com_1” in text box.
¾ Declare port as “567” in port text box.
¾ Describe any name for Named Pipe TCP Proxy e-g Connect terminal to telnet via VMware comm port.
¾ Click “Add” button to apply settings.
¾ Note many pipe name can be assigned but pipe name and port must be different from each other e-g “\\
\\. \pipe\com_2
\pipe\com 2”
Port “568”, “\\. \pipe\com_3” its port “569”…….so on.
See figure
g below
In my case I used “Secure CRT” terminal emulation software, this is a top most, state of the art
terminal
i l emulation
l i software.
f If iit iis not available
il bl other
h terminal
i l emulation
l i software
f may bbe used d
like “putty” windows “Hyper terminal” but the configuration must be same.
I will recommend “VMware workstation 8.0”. This is latest Virtual machine emulation software,
It is user friendly. I will not recommend “Virtual box” or any third party Virtual machine
emulation softwares, because other did not boot up from “pxe” environment due to their
internal errors and bugs. Other thing I will say that I used “Intel Core 2 Duo 1.8, RAM 1GB,
120GB host PC Hard disk, Active LAN connection and minimum partition for OXE R9.0 8GB
(Maximum 40GB) to install Complete Linux + Call handling software. See below to configure
VMware workstation 8.0
Continue………….
C fi
Configuration
ti off VMware
VM workstation
k t ti 8.0
80
Continue………….
Configuration of VMware workstation 8.0
Click on “ Next”
Continue………….
Configuration of VMware workstation 8.0
Click on “ Next”
Continue………….
Configuration of VMware workstation 8.0
Click on “ other,
other
other and Next ”
g
Figure No-8 Configuration
g of VMware workstation 8.0
Continue………….
Configuration of VMware workstation 8.0
Select number of
processors and
click Next
Select amount of
RAM
Click Next
Click Next
Click Next
Click Finish
Select “Output
Output to named pipe
pipe”
and click Next
Click on “Power
ON this virtual
machine”
The VMware will boot up from “pxe” via OmniPCX PC installer tool , and
will show follow messages on screen.
screen
¾ GRUB Loading stage2. Output on the SERIAL line..
¾ Uncompressing Linux.. Ok, booting the kernel.
Note: after above messages, VMware will not show any text on its screen
in case of “Appliance
Appliance server
server” installation and will show installation steps
on “Secure CRT” terminal emulation software. In case of “Blade server”
it will show all installation steps on its screen, but we will unable to
connect any terminal emulation software. Wait for installation until
message displayed “SUCCESSFUL
SUCCESSFUL STANDARD INSTALLATIONINSTALLATION” for
more detail refer to following text in proceeding steps.
DHS3 informations:
==================
address 172.26.66.28
mac 00:0C:29:A7:40:2E
name pxe_linux
netmask 255.255.255.224
gateway
g y 0.0.0.0
server 172.26.66.27
------------
install type 'y'
root directory y "/bootp/linux/62.0/"
p
inst directory "/bootp/linux/62.0/install"
archive path "linux.ram"
tel version "/dhs3mgr/h1301.pk"
Loading g file '/bootp/linux/62.0/linux.ram':
p
................................................................................
................................................................................
................................................................................
................................................................................
................................................................................
................................................................................etc
Installing e-Mediate
e Mediate module (copyright (C) 2000)
********************************************************
********************************************************
*** Setting timezone to Asia/Karachi
*** Creation of user mtcl
*** Creation of user adfexc
*** Creation of user client
*** Creation of the missing main directories
*** Creation of the missing swinst directories
A daily backup will be executed on cpu disk
at 5 hour 45 min
WARNING : no delivery has been installed
The path of the delivery is /dhs3mgr/h1301
The previous version will be erased before the new installation
to avoid for some old files to remain on your CPU.
.............................
end of remove procedure
Transfer for pkg part in preparation
facil/swinst-2.50.0-3oxe.i386.rpm
End of remote copy for pkg part files
LINUX 62.0 is already installed
*** Creation of the missing main directories
*** Creation of the missing swinst directories
Select
S l the
h security
i level
l l:
R) configuration to be restored
0) Level_0 = no security features activated
1) Level_1 = passwords/aging
2)) Level
e e _2 = pass
passwords/aging
o ds/ag g + ttrusted
usted hosts/TCP
osts/ C wrapper
appe
3) Level_3 = passwords/aging + trusted hosts/TCP wrapper + SSH
Security configuration :
[-] Default passwords and no aging password configured.
[-] No isolation from ethernet / no trusted host / no TCP wrapper.
[-] The SSH security is currently NOT set.
(E)localhost localdomain>netadmin -m
(E)localhost.localdomain>netadmin m
NETADMIN menu
Alcatel-Lucent e-Mediate IP Network Administration
==================================================
1. 'Installation'
2. 'Show current configuration'
3. 'Local Ethernet interface'
4. 'CPU redundancy'
5. 'Role addressing'
6. 'Serial
S links (PPP)'
( )
7. 'Tunnel'
8. 'Routing'
9. 'Host names and addresses'
10 'Copy
10. 'C setup''
11. 'Security'
12. 'DHCP configuration'
13. 'SNMP configuration'
14 'VL
14. 'VLan configuration'
fi ti '
15. 'Node configuration'
16. 'Ethernet redundancy'
17. 'History of last actions'
18 'Apply
18. 'A l modifications'
difi ti '
0. 'Quit‘
What is your choice ? 1 Continue……..
Do you want to erase the existing setup (y/n default is 'n') ? y
Continue……..
Ethernet interface setup
========================
Continue……..
Alcatel-Lucent e-Mediate IP Network Administration
==================================================
1. 'Installation'
2. 'Show current configuration'
3. 'Local Ethernet interface'
4 'CPU redundancy'
4. d d '
5. 'Role addressing'
6. 'Serial links (PPP)'
7. 'Tunnel'
8. 'Routing'
9. 'Host names and addresses'
10. 'Copy setup'
11 'Security'
11. Security
12. 'DHCP configuration'
13. 'SNMP configuration'
14. 'VLan configuration'
15. 'Node configuration'
16. 'Ethernet redundancy'
17. 'History of last actions'
18 'Apply
18. Apply modifications'
modifications
0. 'Quit’
What is your choice ? 0
Shutdown Appliance Server CPU
(E)xaVMware>netadmin –m
m
Continue……..
Alcatel-Lucent e-Mediate IP Network Administration
==================================================
1. 'Installation'
2. 'Show current configuration'
3. 'Local Ethernet interface'
4. 'CPU redundancy'
5. 'Role addressing'
6. 'Serial
S links (PPP)'
( )
7. 'Tunnel'
8. 'Routing'
9. 'Host names and addresses'
10 'Copy
10. 'C setup''
11. 'Security'
12. 'DHCP configuration'
13. 'SNMP configuration'
14 'VL
14. 'VLan configuration'
fi ti '
15. 'Node configuration'
16. 'Ethernet redundancy'
17. 'History of last actions'
18 'Apply
18. 'A l modifications'
difi ti '
0. 'Quit‘
What is your choice ? 8 Continue……..
8.Routing setup
===============
1. 'Default
Default router setup'
setup
2. 'Static routes'
3 'D
3. 'Dynamic
i routing
ti (RIP/RSL)'
0. 'Previous menu'
8.2.Static routes
=================
1. 'View'
2. 'Add/Update'
3. 'Delete'
0 'Previous
0. Previous menu'
menu
2. 'Add/Update'
3. 'Delete'
0. 'Previous menu'
8.2.Static routes
=================
1. 'View'
2. 'Add/Update'
p
3. 'Delete'
0. 'Previous menu'
8.Routingg setupp
===============
1. 'Default router setup'
2. 'Static routes'
0. 'Previous menu'
Click on “Properties”
Figure No-26 Configuration of LAN Card Continue……..
LAN Card settings
Click on “Advanced”
Click on “Add”
Enter IP address
Of Appliance
A li S
Server
Continue……..
LAN Card settings
Click on “OK”
( )
(E)xaVMware> swinst
Password: SoftInst
p
•Options 2,2
, &1
Continue……..
SWINST TOOL
ALCATEL-LUCENT
FACILITIES Main menu Installation FACILITIES
2 50 0
2.50.0
1 Easy menu
2 Expert menu
Q Exit
Continue……..
SWINST TOOL
ALCATEL-LUCENT
FACILITIES Expert menu Installation FACILITIES 2.50.0
1 P
Packages
k iinstallation
t ll ti
2 Deliveries installation
3 Cloning & duplicate operations
4 Backup & restore operations
5 OPS configuration
6 System management
7 Database tools
8 Software identity display
9 Remote download
Q Go back to previous menu
Continue……..
SWINST TOOL
ALCATEL-LUCENT
D li
Delivery menu IInstallation
t ll ti
FACILITIES 2.50.0
Continue……..
SWINST TOOL
Enter the name of the server -> 172.26.66.27
The installation of the binaries will modify the current installed version
Please, confirm the installation of a new version (y/n, default y): y
E t the
Enter th full
f ll path
th off th
the d
delivery
li on th
the server
example for Unix server:
/twdhs3/dhs3ref/dhs3ref_d2/E2.504/LIVRAISON
for Windows server: /dhs3mgr/E2504
=> /dhs3mgr/h1301
=> /dhs3mgr/h130126a
Continue……..
SWINST TOOL
Use “swinst” tool to create blank database as given below.
Options 2,7 &2
ALCATEL-LUCENT
FACILITIES Main menu Installation FACILITIES 2.50.0
1 Easy menu
2 Expert menu
Q Exit
Your choice [1..2, Q] ? 2
ALCATEL-LUCENT
FACILITIES Expert menu Installation FACILITIES 2.50.0
1 Packages installation
2 Deliveries installation
3 Cloning & duplicate operations
4 Backup & restore operations
5 OPS configuration
6 System management
7 Database tools
8 Software identity display
9 Remote download
Q Go back to previous menu
Your choice [1..9, Q] ? 7
Continue……..
SWINST TOOL
ALCATEL-LUCENT
Database tools menu Installation FACILITIES 2.50.0
1 Database translation
2 Create an empty database
3 Remove database
4 Acd stat files translation
Q Go back to previous menu
Your choice [1..4, Q] 2
Warning the current database will be erased
Warning,
Please confirm the creation of a new database (y/n, default y): y
running RUN_MKBDD
Removing the old database...
Deleting sample data files...
files
Creating empty dictionary files
newfils finished...
Old database removed.
-- Creation of the tables --
Continue……..
SWINST TOOL
AVAILABLE COUNTRIES
=============
ARGENTINA (AR) AUSTRALIA (AS)
AUSTRIA (AU) BAHRAIN (BH)
BANGLADESH (BD) BRAZIL (BR)
BELGIUM (BE) BULGARIA (BG)
CAMBODIA ((KH)) CHILE ((CL))
CHINA (CN) COLOMBIA (CO)
COSTA RICA (CR) COTE D'IVOIRE (CI)
CROATIA (HR) CYPRUS (CY)
CZECH REPUBLIC (CZ) DENMARK (DE)
ECUADOR (EC) EGYPT (EG)
EL SALVADOR (SE) ESTONIA (EE)
ETHIOPIA (ET) EXPORT 1 (X1)
EXPORT 2 (X2) EXPORT 3 (X3)
Continue……..
EXPORT 4
SWINST TOOL
(X4) EXPORT 5 (X5)
FINLAND (FI) FRANCE (FR)
FRENCH POLYNESIA (PF) GERMANY (GE)
GREECE (GR) HONG KONG (HK)
HUNGARY (HU) INDIA (IN)
INDONESIA (ID) IRAN (IR)
IRELAND (IE) ISRAEL (IL)
ITALY (IT) JAPAN (JP)
KENYA (KE) KOREA (KR)
KUWAIT (KW) LAO (LA)
LATIN AMERICA (LN) LATVIA (LV)
LEBANON (LB) LITHUANIA (LT)
LUXEMBOURG (LX) MALAYSIA (MY)
MALDIVESS ((MV)) MALTA ((MT))
MEXICO (MX) MOROCCO (MA)
MYANMAR (MM) NEPAL (NP)
NETHERLANDS (NL) NEW ZEALAND (NZ)
NIGERIA (NG) NORWAY (NO)
OMAN (OM) PAKISTAN (PK)
PERU (PE) PHILIPPINES (PH)
POLAND (PL) PORTUGAL (PT)
ROMANIA (RO) RUSSIA CIS (SU)
SAUDI ARABIA (SA) SENEGAL (SN)
SINGAPORE (SG) SLOVAKIA (SL)
SLOVENIA (SI) SOUTH AFRICA (ZA)
SPAIN (SP) SRI LANKA (LK)
SWEDEN (SV) SWISS (CH)
SYRIAN REPUBLIC (SY) TAIWAN (TW)
THAILAND (TH) TUNISIA (TN)
TURKEY ((TR)) U.A.E ((AE))
UK (UK) URUGUAY (UY)
UNITED STATES (US) VENEZUELA (VE)
VIET NAM (VN) YUGOSLAVIA (YU)
ZIMBABWE (ZB)
Continue……..
SWINST TOOL
Enter
E t the
th country
t name symbol
b l (0 to
t Quit).
Q it)
Your choice: pk
Continue……..
SWINST TOOL
-- Creation
C ti off the th tones
t --
>> deleting old tones tables
>> creating new tones tables
Startingg initialization of tones for PAKISTAN
->commit success
Table initialization OK
Note: Change the values of each option 20, 22, 28 in configuration
menu.
menu
After creation of a new database it should be better to reboot the CPU
Please proceed to CPU reboot before starting the telephone application
Press return
(At this point press q, q ,q to exit from “swinst” menu)
bye bye
(E)xaVMware> shutdown –r now
Broadcast message from root (ttyS0) Sat Mar 10 06:02:26 2012...
2012
The system is going down for reboot NOW !!
INIT: Switching to runlevel: 6
(E)xaVMware>
INIT: Sending processes the TERM signal
Continue……..
SWINST TOOL
UPLOADING OF “OPS”
After restart login to Call Server
xaVMware> login:g mtcl ((Default user name for mtcl account))
Password : mtcl (Default password for mtcl user account)
Via FTP client software (total commander) transfer the ops File to
/usr4/BACKUP/OPS (only OPS files)
Continue……..
SWINST TOOL
UPLOADING OF “OPS”
Continue……..
SWINST TOOL
UPLOADING OF “OPS”
Continue……..
Use “swinst” tool to set “Autostart” option
swinst
SoftInst
options 2, 6, 2 & 1