Professional Documents
Culture Documents
9.2.1.6 MANHOLES
Manholes for the drainage lines outside the building shall be
precast R.C. sections with galvanized steel ladder rungs and
cast-iron frame and cover.
The soil, waste, and vent must be provided with cleanouts to make them
accessible, and when completed be subjected to a water test in the
presence of a local authority and the Construction Officer.
181
9.2.2.2 YARNING MATERIALS
Use Oakum for B & S joint with cement mortar filling the
remaining annular space.
The building service is to be extended from the city main with Polyvinyl
Chloride (PVC) pipe of extra strong quality and laid on a shelf in the trench of
the storm drainage. It is to be equipped with a corporation stop, a curb stop
with stop box extended flush with the grade and a meter stop.
9.2.3.4 UNIONS
Unions on ferrous pipes shall be malleable iron and shall
conform to the requirements of U.S. Federal Specifications
WW-U0-531, Type B zinc-coated.
Plumbing and fixture trim shall be provided complete with fittings. Exposed
traps and supply pipes for all fixtures and equipment shall be connected to
the rough piping systems at the wall unless otherwise indicated. Floor
182
plates, wall plates and escutcheons shall be as required by the fixtures
specified. Straps shall be provided at each fixtures. Plumbing fixture
compound shall be fixed for fixture connections between earthen ware
fixtures and flanges on soil pipe. Closet bolts shall be not less than 8m. The
exposed piping, fittings and trimmings shall be chromium-plated or nickel-
plated brass with polished bright surfaces.
For all water closets use Saniwares VENTURA Model No. PF 3554 FV, color
verify.
For all urinal, use Saniwares WASHBROOK Model No. PF 6500, color verify.
9.2.5 VALVES
9.2.6 DRAINS
9.3 SUBMITTALS
Submit samples of fixtures and pipes to Construction Officers (CO) prior to installation. Also
submit working drawings upon the dictated of the CO.
9.4 WORKMANSHIP
All piping must be substantially supported to overcome sagging and be so arranged that it
may be easily drained.
9.5 INSTALLATION
183
Provide a complete system of storm drainage piping for all roofs, set-back
areas, parking areas and canopies. Connect to the house drainage system at
the building wall.
Provide all drains required to conduct rain water from the building surfaces
to the storm drainage system, including all of the scheduled drains and any
special drains indicated on the Architectural and/or Plumbing Drawings.
Take special care in roof drains to assure that they are set at an elevation
which will practice the formation of puddles.
Make all branch connections to drainage system “wye” and long “tee-wye”
fittings. Do not use short ¼bends, common offsets and double hubs. Use
short “tee-wye” fittings, in vertical piping only, and only where space
conditions will not permit the use of long turn fittings. Use only fittings that
conform to code requirements.
184
the fixture before connecting with any other pipe. In
general, this will be approximately 1.067 meters (3 feet, 6
inches) above the finish floor. Pitch branch vents back to
the fixtures.
The system shall include the required meters and meter accessories.
The water supply system shall be complete with all pipe fittings, valves,
meters, trenching, shoring, backfilling, mains, risers, branches, air chambers,
controls, hangers, anchors, protective painting, insulation, tests, and the
like, all as shown on the drawings, as hereinafter specified and in
accordance with the regulations of authorities having jurisdiction.
Adjust all fixtures stops so that flush valves, faucets, etc., function quietly
and efficiently before final acceptance by the Owner.
Provide tapping valves, curb valves, boxes and signs where required by the
authorities having jurisdiction.
9.6 TEST
9.6.1 STORM DRAINAGE SYSTEM TEST
185
The entire drainage and venting system shall have all the necessary openings
which can be plugged to permit the entire system to be filled with water to
the level of the highest stack vent and/or vent stack above the roof.
The system shall hold this water for a full thirty (30) minutes during which
time there shall be no drop more than 100 millimeters (4 inches). If and
when the owner decides that an additional test is needed, such as an air or
smoke test on the drainage system, the Contractor shall perform such tests
without additional cost to the Owner.
Upon completion of the roughing-in and before setting fixtures, the entire
cold water piping system shall be tested at hydrostatic pressure one and a
half (1½) times the expected working pressure in the system when in
operation, and proved tight at this pressure.
Where a portion of the water-piping system is to be concealed before
completion, this portion shall be tested separately in a manner similar to
that described for the entire system, land in the presence of the
Construction Officer.
9.6.2.1 DISINFECTING
The entire water system shall be thoroughly flushed and
disinfected with chlorine before it is placed in operation.
9.7 GUARANTEE
The Plumbing Contractor does hereby guarantee the entire work, plumbing and drainage
system installed against mechanical defect, for a period of one year from the completion of
the work. The Contractor agrees to replace of defective materials and make good any
damage done to the building in the performance of this Contract cost to the Owner.
186
Section VII. Drawings
187
CW-1 BRGY. LUMALANTANG , ZUMARRAGA ISLAND
CW-2
CW-3
CW-4
A-1
S-1
P-1
LAYOUT PLAN
SCALE 1 :300 M
SITE
SITE
Reviewed by: Checked by: PROJECT NAME : Sheet Content: DRAWN BY: - Revisions: Sheet No.:
ATIO
OR T N REPUBLIC OF THE PHILIPPINES
SP
N
CW-1
D
The copyright of this drawing remains the property of the Department of Transportation and Communications whose permission must be obtained before any use of it can be made.
CROSS SECTION
SCALE 1 :100 M
CENTERLINE PROFILE
SCALE 1 :300 M
Reviewed by: Checked by: PROJECT NAME : Sheet Content: DRAWN BY: - Revisions: Sheet No.:
ATIO
OR T N REPUBLIC OF THE PHILIPPINES
SP
N
CW-2
D
The copyright of this drawing remains the property of the Department of Transportation and Communications whose permission must be obtained before any use of it can be made.
TYPICAL SECTION DETAIL
SCALE 1 : 50 M
SECTION
Reviewed by: Checked by: PROJECT NAME : Sheet Content: DRAWN BY: - Revisions: Sheet No.:
ATIO
OR T N REPUBLIC OF THE PHILIPPINES
SP
N
CW-3
D
The copyright of this drawing remains the property of the Department of Transportation and Communications whose permission must be obtained before any use of it can be made.
T
T
HINGED CONSTRUCTION (J-4) DUMMY CONTRACTION (J-7) DOWELED BUTT CONSTRUCTION (J-8)
Reviewed by: Checked by: PROJECT NAME : Sheet Content: DRAWN BY: - Revisions: Sheet No.:
ATIO
OR T N REPUBLIC OF THE PHILIPPINES
SP
N
CW-4
D
The copyright of this drawing remains the property of the Department of Transportation and Communications whose permission must be obtained before any use of it can be made.
A B C
A B C 2 1
1 1
2 2
A B C
SIDE ELEVATIONS
SCALE 1 : 50 M
PERSPECTIVE
Reviewed by: Checked by: PROJECT NAME : Sheet Content: DRAWN BY: - Revisions: Sheet No.:
ATIO
OR T N REPUBLIC OF THE PHILIPPINES
SP
N
CW-5
D
The copyright of this drawing remains the property of the Department of Transportation and Communications whose permission must be obtained before any use of it can be made.
A B C A B C
1 1
2 2
BEAM DETAIL
ROOF DECK TYPICAL FLOOR BEAM/ROOF CANTILIVER BEAM
TYPICAL SLAB DETAIL BEAM/GIRDER SECTION SECTIOM
SCALE 1 : 20 M
Reviewed by: Checked by: PROJECT NAME : Sheet Content: DRAWN BY: - Revisions: Sheet No.:
ATIO
OR T N REPUBLIC OF THE PHILIPPINES
SP
N
CW-6
D
The copyright of this drawing remains the property of the Department of Transportation and Communications whose permission must be obtained before any use of it can be made.
A B C A B C
1 1
2 2
Reviewed by: Checked by: PROJECT NAME : Sheet Content: DRAWN BY: - Revisions: Sheet No.:
ATIO
OR T N REPUBLIC OF THE PHILIPPINES
SP
N
CW-7
D
The copyright of this drawing remains the property of the Department of Transportation and Communications whose permission must be obtained before any use of it can be made.
Section VIII. Bill of Quantities
195