Professional Documents
Culture Documents
FOR
0 21/11/15 6 DCS BMG DS RR RY
CONSTRUCTION
ISSUED FOR
C 11/11/14 6 DCS BMG DS RR RY
CONSTRUCTION
ISSUED FOR
B 30/10/14 6 DCS BMG DS RR RY
APPROVED
ISSUED FOR
A 27/09/14 6 DCS BMG DS RR RY
REVIEW
DIBUAT DIPERIKSA DISETUJUI DIPERIKSA DISETUJUI
JUM OLEH OLEH OLEH OLEH OLEH
REV TGL STATUS
HAL PT. MISI MULIA
PT. PP (PERSERO)
PETRONUSA
REVISION SHEET
1 INTRODUCTION
1.1 Scope
1.2 Definition
2 ABREVIATIONS
3 AMBIEN CONDITIONS WATER SOURCE
4 REFERENCE DOCUMENTS
5 STANDARD OF MATERIAL PIPING LPG SYSTEM
6 INTERNAL CORROSION ROTECTION
7 REGULAR PIPELINE CLEANING
8 EXTERNAL CORROSION PROTECTION
8.1 Atmospheric Corrosion
8.2 Corrosion Protection
8.3 Fireproofing
1.1 Scope
1.2 DEFINITION
The following terms used in this specification shall refer to the meanings given below :
2. ABREVIATION
o CA Corrossion allowance
o CC Crevice corrosion
o CCT Critical crevice corrosion temperature
o CP Cathodic Protection
o CPT Critical pitting corrosion temperature
o CRA Corrosion resistannt alloy
o CS Carbon manganesse steels
o CSCC Chloride induced stress corrossion cracking
o FRP Fiber Reinforced Plastic
o GRP Fiber Reinforced Plastic
o HIC Hydrogen inducedd cracking
o ICCP Impressed Current Cathodic Protection
o LTCS Low Temperature carbon steel
o MIC Microbiological induced corrossion
o NACE Nationnal Association of Corrossion Engineers
o PT Pitting corosion
o ppmv Parts per million b volume
o ppbv Parts per billion by volume
o Pint Equals to 0.125 gaallon
o SS Stainless steel
Piping LPG system shall be indicated or suspected to leakage or spill of liquid. Because of the fire
hazard in piping system that are handling flammable and combustible liquids. Piping system
must be able to withstand the intense heat generated by fire for reasonable periods
of time while emergency shutdown procedures are implemented and fire fighting measures
begin. Failure of piping during fire condition can turn moderate hazard into catastropic.
The Material, design, fabrication, assembly, test and inspection piping systems containing liquids
shall be suitable for the expected working pressure and structural stresses. Conformitty with the
applicable section of ANSI B31.3, American National Standard Code for Process Piping, and
ANSI B31.4 Pipe Line Transportation For Liquid Hydrocarbon and Other Liquids .
The other material plastic or similar materials, as permitted and shall be designed to specification
embodying recognized engineering principles or shall be listed and shall be compatible with the
fluid services. Consideration Material is;
There is need to consider to external coating with fire proofing coating for pipe support and other
structure to holding sufficient fire resistance. Carbon steel pipe must be applied for fire water line.
Utilization of FRP & GRP pipe is strickly not allowed.
Carbon steel piping and equipment expose to a humid atmospheere will be subject to atmospheric
corrosion. Since atmospheric corrosion is an electrolytic proccess, the presence of water is required.
Apart from wetting by rainstorms, surfaces can have an adsorbed layer of water if the relative
humidity of the surrounding atmosphere is sufficiently high. It is generally accepted that relative
humidity in excess of about 70% lead to adsorbed layers of water molecules.
This layer in combination with salt contamination from the marine environment will lead
to general surface corrosion and Possible pitting corrosion. The corrosion of bare carbon steel in
atmosphere is severe and hence all surfaces shall be coated in atmospheric.
8.3 Fireproofing
a) Drainage to a safe location to prevent liquid from accumulating under pipe ways
b) Fire resistive construction
c) Fire resistant protective coating system
d) Water spray system designed and installed in accordance with NFPA 15, standard
for water spray fixed system for fire protection
e) Other alternative material acceptable and as long having jurisdiction.