Professional Documents
Culture Documents
AIR CONDITIONER
Please read this manual carefully before operating
your air conditioner and retain it for future reference.
www.lgappliances.com
INTRODUCTION
TROUBLESHOOTING
Before Calling for Service . . . . . . . . . . . . . . . . . 21,22
WARRANTY
Product Registration Information . . . . . . . . . . . . . . .23
2
IMPORTANT SAFETY INSTRUCTIONS
CAUTION This symbol indicates the possibility of personal injury or property damage.
English
BASIC SAFETY PRECAUTIONS
WARNING To reduce the risk of fire, electric shock, or personal injury
when using this appliance, follow basic precautions, including the following:
• Do not attempt to repair or replace any part • Make sure the power cord is plugged firmly and
of your air conditioner unless it is specifically completely into the outlet. It can result in the risk
recommended in this manual. All other services of electric shock or fire.
should be referred to a qualified technician. • Do not start or stop operation by plugging in or
• If the power cord becomes worn or damaged, unplugging the power cord. It can result in the
the cord should be replaced only by a qualified risk of electric shock.
service technician using genuine replacement • If the air conditioner is making unusual sounds or
parts. is emitting smoke or an unusual odor, unplug it
• The air conditioner should be plugged into its immediately. It can result in the risk of electric
own grounded 15A, 60 Hz., 120 VAC circuit. shock or fire.
• Do not plug other appliances into the same • Do not use if the electrical socket is loose or
outlet; it can overload the circuit and cause a fire damaged. It can result in the risk of electric
or electric shock. shock or fire.
• Do not remove the round grounding prong from • Do not operate with wet hands or in a damp
the plug. It can result in the risk of electric shock. environment. It can result in the risk of electric
• This air conditioner is not designed for use by shock.
young children. Young children should be • Do not use this or any electrical appliance if you
supervised to ensure that they do not play with smell gas. It can result in the risk of fire or
or climb on the air conditioner. explosion.
• Be sure all packaging materials are removed • Turn off and unplug the air conditioner before
from the air conditioner before use. It can result cleaning to avoid the risk of electric shock.
in personal injury. • Do not clean the unit with water. Water can enter
• Do not disassemble or modify the air conditioner the unit and damage the insulation, creating a
or the power cord. It can result in the risk of shock hazard. If water enters the unit, unplug it
electric shock or fire. immediately and contact Customer Service. It
• Do not place the power cord or air conditioner can result in the risk of electric shock.
near a heater, radiator, or other heat source. It • Use two or more people to lift and install the
can result in the risk of electric shock or fire. unit. Failure to do so can cause back injury or
• Do not use this or any appliance near flammable other injuries.
gases or liquids or other combustibles, such as
gasoline, benzene, thinner, etc. It can result in
the risk of electric shock or fire.
3
I M P O RTA N T S A F E T Y I N S T RU C T I O N S
ELECTRICAL SAFETY
• This air conditioner must be plugged
WARNING into a grounded 60 Hz, 120 VAC outlet
protected by a 15 amp time delay fuse
Electrical Shock Hazard or circuit breaker.
Failure to follow these instructions can result
in death, fire, or electrical shock. • This air conditioner must be installed in
• This unit must be properly grounded. accordance with national wiring codes.
• Do not, under any circumstances, cut or • Do not alter or modify the plug or cord
remove the ground prong. of this air conditioner. If the power cord
becomes worn or damaged, the cord should
• If you do not have a properly grounded only be replaced by a qualified service
outlet, or if there is any doubt that the outlet technician using genuine replacement parts.
is not properly grounded, a qualified
electrician should check the outlet and • Do not use an extension cord.
circuit, and, if necessary, install a properly
grounded outlet.
4
IMPORTANT SAFETY INSTRUCTIONS
ELECTRICAL SAFETY
English
should be tested
periodically by
pressing the TEST
button then the RESET button. If the TEST
button does not cause the circuit breaker to trip,
or if the RESET button will not stay engaged,
unplug the air conditioner immediately and
contact your LG service technician.
5
PARTS AND FEATURES
1 AIR DISCHARGE
The direction of air can be controlled wherever you want to cool
by adjusting the horizontal louver.
4 1
The horizontal direction is adjusted by moving the lever to the left
or right.
Touching the horizontal louvers adjusts the air direction up or
down.
2 CONTROL PANEL AND DISPLAY
Easy-to-read digital display shows the set temperature and 3
indicator lights show the operating mode. Simple push buttons
make changing settings quick and easy.
3 SWIVELING CASTERS
Swiveling casters allow you to move the air conditioner easily
on most floor surfaces.
4 INTEGRATED HANDLES
Integrated handles provide a convenient grip when lifting the 5
air conditioner.
8
5 INFRARED REMOTE CONTROLLER
Dry
7 AIR FILTER
6
HOW TO USE
English
positioned where it does not create a
tripping hazard and will receive adequate
ventilation. Do not place it directly next to
furniture or objects that could block the
vent openings.
3 Make sure that any items that could be
blown over or damaged by the airflow from
the fan are out of the airflow path.
IMPORTANT:
• Do not remain in the direct airflow from the air
conditioner for extended periods of time.
• When used at the same time as stoves,
fireplaces, and other combustion devices,
make sure there is a sufficient flow of fresh air
into the room. Do not use in tightly enclosed
spaces with these types of devices.
• This air conditioner is intended for household
use as a consumer comfort appliance. Do not
use it as a precision climate control system,
or for purposes such as cooling precision
equipment, food, pets, plants, artwork, etc.
Such items could be damaged.
• Do not bend the hose downward when
window installation kit is not applied. It may
cause failure of air conditioner or performance
deterioration.
7
HOW TO USE
English
NOTE :
Use only alkaline batteries. Do not use
rechargeable batteries.
When replacing batteries, always replace both
batteries with new batteries. Do not mix old
and new batteries.
If the air conditioner will not be used for an
extended period of time, remove the batteries
from the remote.
CAUTION
• Iftheliquidfromthebatteriesgetsontoyourskinorclothes,washitwellwithcleanwater.
Do not use the remote if the batteries have leaked.
• Ifyoueattheliquidfromthebatteries,brushyourteethandseedoctor.
The chemicals in batteries could cause burns or other health hazards.
8
HOW TO USE
Dry
3
3 Dry
2
97
7 88 8
4
4 11
4 3 5 2 1
English
or the control panel, unless otherwise stated.
NOTE:
The remote sensor is located under the LED display.
Point the remote anywhere at the sensor. The remote may
not work if the sensor is in bright light or if there is not a
clear path between the remote and the sensor.
1 POWER 4 TIMER
Press the POWER button to turn the air conditioner When the TIMER function is selected, you can set
ON or OFF. Any control settings such as Cool, Dry, the air conditioner to either automatically turn
Fan, and Fan Speed will be retained in memory when OFF or turn ON after a delay of up to 24 hours.
the power is off. When turned on after being The display will show 0. Use the buttons
unplugged, the air conditioner will automatically to adjust the delay time from 1 to 24 hours, in one
reset. Any settings will need to be re-entered. hour increments.
To set an automatic off delay, press the TIMER
2 MODE button while the air conditioner is running and
Press this button to select the operating mode such use the buttons to adjust the delay time.
as Cool, Dry (Dehumidify), or Fan for the air conditioner. air conditioner will automatically turn off after the
And you can see the active mode through the set delay.
indicator lights.The default setting is Cool. Press the To set an automatic on delay, press the TIMER
MODE button to change to Dry (Dehumidify), press button while the air conditioner is off and use
again to change to Fan, and again to change to Cool. the buttons to adjust the delay time.
The display will show the number of hours
Mode Features
remaining until the unit is set to come on. The
COOL Compressor runs and cools the room. Use the
/ and FAN buttons to set the desired air conditioner will automatically turn on after
temperature and circulation fan speed. the set delay.
FAN Fan circulates air but compressor does not run. If you want to know how many hours you have
Use the FAN button to set the desired fan speed. setted, press the TIMER button and then you
DRY Dry mode is used to remove humidity from can see the time through the LED display.
the room without additional cooling.
Fan speed is pre-set and cannot be adjusted.
If you want to change the set timer, press the
TIMER button and adjust the time when the
number is flickering.
3 FAN To cancel the Timer function, press the TIMER
Adjusts the circulation fan speed between High and button and adjust the number to 0 when the
Low fan speed. The selected fan speed will be number is flickering, then the function will be
shown through the indicator lights. The function can canceled in a few seconds.
be used in Cool and Fan modes. When changing Another better method is press the TIMER
fan speeds, there is a brief delay before the fan button and press this button again when the
motor changes speed. number is still flickering.
9
HOW TO USE
Dry
3 Dry
2
9
7 88 8
4 11 1
4 3 5 2 1
English
or the control panel, unless otherwise stated.
NOTE:
The remote sensor is located under the LED display.
Point the remote anywhere at the sensor. The remote may
not work if the sensor is in bright light or if there is not a
clear path between the remote and the sensor.
5 / (TEMP/TIMER) 7 SLEEP
In COOL and DRY modes, the buttons Increases the temperature by 1 °F every 2 hours
adjust the set temperature up to 86°F or down to to allow a more comforable adjustment for the user.
60°F, in one degree increments. The temperature
can be switched between degrees Fahrenheit and
degrees Celsius, pressing the button and 8 °C/°F(CELSIUS AND FAHRENHEIT
button at the same time, or pressing °F /°C button
on the remote. EXCHANGE BUTTON)
When the TIMER function is selected, use the
buttons to adjust the delay time from 1 to °C/°F function can be activated only with the
24 hours, in one hour increments. remote. When the displayed temperature is
If you press and hold the buttons, the set °C (or °F), you can press this button to switch to
temperature or time will change automatically after °F (or °C).
a few seconds.
NOTE: The displayed temperature is the SET
temperature, not the room temperature. In COOL or 9 CONTINUOUS
DRY mode, the thermostat in the air conditioner
will run the compressor until the set temperature is After setting continuous, the unit will keep running
reached, then cycle the compressor on and off to no matter what temperature is selected.
maintain the set temperature.
6 LED Display
10
INSTALLATION INSTRUCTIONS
EXHAUST COMPONENTS
The following components are used for window venting.
Not all components are used for every installation.
English
Flexible Venting Hose Diffuser
11
INSTALLATION INSTRUCTIONS
WARNING
The length of the exhaust hose is specially designed according to the specification of this product.
Do not replace or extend it with your own private hose as this could cause malfunction.
ATTACHING THE HOSE AND DIFFUSER
UNL
OCK
CK
LO
12
INSTALLATION INSTRUCTIONS
A
Type B C D
Fig
Window Length 18" 12" 18" 16" Vent Panel(A) Small (B)
Extension
18" √ a Panel
18 1/4"−28" √ √ √ b Extension (D)
Vent Panel
28 1/4"−34" √ √ √ c Large (C)
Extension
34 1/4"−48" √ d Panel
Window Installation Kit
(includes 2 Window Vent
Panel and 2 Extension
Panels)
English
Small extension
panel
Small
extension
18" panel
181⁄4" − 28"
For an 18" window opening, use the window For window openings from 181⁄4" to 28",
vent panel by itself. use the window vent panel and the small
extension panel.
Fig “a” Fig “b”
28 1/4"−34" 34 1/4"−48"
Large Vent Large Vent
extension Panel extension Panel
panel panel
Vent Vent
Panel Panel Small
extension
panel
Small
extension
34 1/4"−48" panel
For window openings from 28 1/4" to 34", For window openings from 34 1/4" to 48", use the
use the window vent panel and the large window vent panel and both extension panels.
extension panel.
Fig “c” Fig “d”
13
INSTALLATION INSTRUCTIONS
Foam seal C
(Adhesive type-shorter)
Extension panel
(if required)
Vent
Panel
Foam seal A
(Adhesive type)
1 Cut the foam seal A (adhesive type) & 2 Insert the vent panel assembly, including
C (adhesive type-shorter) TipotoCthe proper
de sellado con espuma extension panels, if needed, into the window
length, and attach it to the
(tipo window sash
adhesivo-más corto). opening. Extend the extension panels, if
and frame. used.
Sellante de espuma A
(Tipo adhesivo) Foam seal B
(Non-adhesive type)
Type A screws
Joints en Mousse C
(Plus court de type adhésif)
3 Carefully lower the window. Secure the vent 4 Cut the foam seal B (Non-adhesive type) to
panel in place with 4 type A screws, plus the window width. Stuff the foam seal B
one screw for each extension. between Joints
the glass andA the window to
en Mousse
(Adhesive type)
Vent panel only: 4 type A screws prevent air and insects from getting into the
Vent panel and room.
one extension: 5 type A screws
Vent panel and
two extensions: 6 type A screws
Two vent panels and
two extensions: 10 type A screws
14
INSTALLATION INSTRUCTIONS
Security Bracket
Type A
screw
English
5 Install the security bracket with a type A 6 Insert the oval end of the diffuser into the
screw, as shown. window installation kit until the locking tabs
engage.
Small gap
Second
First
15
I N S TA L LA T I O N I N S T R U C T I O N S
Foam seal C
(Adhesive
type-shorter) Extension panel
(if required)
Vent
Foam seal A Panel
(Adhesive type)
1 Cut the foam seal A (adhesive type) & 2 Insert the vent panel assembly, including
C (adhesive type-shorter) to the proper extension panels, if needed, into the window
length, and attach it to the window sash and opening. Extend the extension panels, if
frame. used.
Sellado con
espuma C
(tipo adhesivo-
más corto)
Foam seal B
(Non-adhesive type)
Sellado con
espuma A
(tipo adhesivo)
Type A screws
3 Carefully close the window. Secure the vent 4 Cut the foam seal B (Non-adhesiveJoints
type) en to
panel in place with 4 type A screws, plus the window height. Stuff the foam seal
MousseBC
one screw for each extension. between the glass and the window(plusto court de
type adhésif)
Vent panel only: 4 type A screws prevent air and insects from getting into the
Sellado con esp
Vent panel and room. (tipo adhesivo)
one extension: 5 type A screws
Vent panel and
two extensions: 6 type A screws
Two vent panels and
two extensions: 10 type A screws
16
INSTALLATION INSTRUCTIONS
Security
bracket
Type A screw
English
5 Install the window security bracket with a 6 Insert the oval end of the diffuser into the
type A screw, as shown. window installation kit until the locking tabs
engage.
Small gap
Second
First
17
CARE AND CLEANING
Your air conditioner is designed for year-round For maximum efficiency, it is recommended
operation with only minimal cleaning and that you have the cooling coils inspected and
maintenance. cleaned annually. Your local LG Authorized
Service Center can provide this inspection
WARNING and cleaning service for a nominal fee.
• Unplug the air conditioner before cleaning or performing any maintenance or servicing.
• Be careful when cleaning coils or removing or reinstalling the filter—the cooling fins are
sharp!
Failure to follow the above precautions could result in electrical shock or personal injury.
WATER
A DRAINAGE
This product has a self-evaporative system. The condensing water will be recycled to cool the
condenser. This can not only improve cooling efficiency, but also save energy for you.
Using the Upper Drain Port (Dry Mode Only)
• This can be used when you need dehumidification in high humidity.
• Under the Cool or Fan mode, there’s no need of using the upper drain port.
• During DRY(dehumidifying) mode, remove the drain plug and the exhaust hose from the back of the unit.
• Install a drain hose (12mm [1/2"] inside diameter) and place the open end of the hose at a suitable drain
location or outdoors.
18
CARE AND CLEANING
English
CLEANING THE AIR FILTER
The air filter should be cleaned every two weeks; depending on indoor air quality, more
frequent cleaning may be needed. A dirty air filter will decrease airflow and reduce efficiency.
19
CARE AND CLEANING
20
TROUBLESHOOTING
Air The air conditioner is Make sure the air conditioner plug is pushed
conditioner unplugged. completely into the outlet.
does not The fuse is blown/circuit
start Check the house fuse/circuit breaker box and
breaker is tripped. replace the fuse or reset the breaker.
Power failure. If power failure occurs, turn the mode control
to Off. When power is restored, wait 3 minutes
to restart the air conditioner to prevent tripping
English
of the compressor overload.
The current interrupter Press the RESET button located on the power
device is tripped. cord plug. If the RESET button will not stay
engaged, discontinue use of the air conditioner
and contact a qualified service technician.
FL appears in the display. The water collection tank is full. Drain the tank
and reset your settings.
Room temperature is less This is normal. The air conditioner automatically
than the set temperature. shuts off when the room equals or is less than
the set temperature. Adjust the temperature
setting, if needed.
Air conditioner Airflow is restricted. Make sure there are no curtains, blinds, or
does not cool furniture blocking the front of the air conditioner.
as it should
The temp control may not In COOL model,press the DECREASE pad.
be set correctly.
The air filter is dirty. Clean the filter at least every 2 weeks.
See the Care and Cleaning section.
The room may have been When the air conditioner is first turned on, you
hot. need to allow time for the room to cool down.
Air conditioner The cooling coils are iced Ice may block the air flow and obstruct the air
freezing up over. conditioner from properly cooling the room.
Set the mode control at High Fan or High Cool.
Air conditioner Area to be cooled is too Consult your dealer for the air conditioner
runs too often large for the air conditioner. capacity necessary to cool the desired area.
or too long
Doors or windows are open. Make sure doors and windows are closed.
21
TROUBLESHOOTING
Code
appears in
the display.
FL The water collection tank Empty the water collection tank.
is full. See the Care and Cleaning section.
E1 Short or open circuit in the Unplug the air conditioner and contact your
indoor air thermostat. authorized LG service center.
E2 Short or open circuit in the Unplug the air conditioner and contact your
indoor pipe thermostat. authorized LG service center.
E4 The coil sensor temperature After defrost, the unit will re-start.
is low, the unit will stop
and display E4 to defrost.
22
WARRANTY
WARRANTY PERIOD:
1 year from the Date of Purchase: Any internal/ functional Parts and Labor.
THIS WARRANTY IS IN LIEU OF ANY OTHER WARRANTY, EXPRESS OR IMPLIED, INCLUDING AND WITHOUT LIMITATION TO, ANY
WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. TO THE EXTENT ANY IMPLIED WARRANTY IS
REQUIRED BY LAW, THIS WARRANTY IS LIMITED IN DURATION TO THE TERM PERIOD EXPRESSED ABOVE. REPAIR OR
REPLACEMENT AS PROVIDED UNDER THIS WARRANTY IS THE EXCLUSIVE REMEDY FOR THE CUSTOMER. NEITHER THE
MANUFACTURER NOR ITS U.S. DISTRIBUTOR SHALL BE LIABLE FOR ANY INCIDENTAL, CONSEQUENTIAL, INDIRECT, SPECIAL, OR
PUNITIVE DAMAGES OF ANY NATURE, INCLUDING AND WITHOUT LIMITATION TO, LOST REVENUES OR PROFITS, OR ANY OTHER
DAMAGE, WHETHER BASED IN CONTRACT, TORT, OR OTHERWISE.
SOME STATES DO NOT ALLOW THE EXCLUSION OR LIMITATION OF INCIDENTAL OR CONSEQUENTIAL DAMAGES OR LIMITATIONS
ON HOW LONG AN IMPLIED WARRANTY LASTS, SO THE ABOVE EXCLUSION OR LIMITATION MAY NOT APPLY TO YOU. THIS
WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS AND YOU MAY ALSO HAVE OTHER RIGHTS THAT VARY FROM STATE TO STATE.
INSTRUCCIONES DE SEGURIDAD
IMPORTANTES
Precauciones básicas de seguridad . . . . . . . . . .25,26
Seguridad eléctrica . . . . . . . . . . . . . . . . . . . . . . .26,27
¡GRACIAS!
PIEZAS Y CARACTERÍSTICAS
Piezas y componentes clave . . . . . . . . . . . . . . . . . .28 Felicitaciones por su compra y
LG combina un funcionamiento
INSTRUCCIONESDEINSTALACIÓN de alta eficiencia con la comodidad
Preparación para la instalación . . . . . . . . . . . . . . . . 33
Elección de ubicación para la instalación . . . . . . . . 34
Cómo conectar la manguera y el difusor . . . . . . . . . 34 de la portabilidad.
Paneldeventilaciónyextensionesde
laventana. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35 Siguiendo las instrucciones de
Instalaciónenventanasde
deslizamientovertical . . . . . . . . . . . . . . . . . . 36,37
Instalaciónenventanasde
funcionamiento y cuidados de este
deslizamientohorizontal . . . . . . . . . . . . . . . . 38,39
manual, su acondicionador de aire
DETECCIÓN DE PROBLEMAS
Antes de llamar al servicio técnico . . . . . . . . . . . 43,44
GARANTÍA
Información sobre registro de producto. . . . . . . . . . 45
24
INSTRUCCIONES DE SEGURIDAD IMPORTANTES
Español
piezas de repuesto genuinas. • Si el acondicionador de aire está haciendo sonidos
• El aire acondicionado debe enchufarse en su inusuales o está emitiendo humo u olor poco
propio circuito de 15A, 60 Hz., 120 VAC con común, desenchúfelo de inmediato. Puede
conexión a tierra. provocar un riesgo de descarga eléctrica o
• No enchufe otros artefactos en el mismo incendio.
tomacorriente ya que puede sobrecargar el circuito • No lo use si el tomacorriente está suelto o dañado.
y provocar un incendio o descarga eléctrica. Puede provocar un riesgo de descarga eléctrica o
• No quite la pata redonda de conexión a tierra del incendio.
enchufe. Puede provocar un riesgo de descarga • No lo opere con manos mojadas o en un medio
eléctrica. húmedo. Puede provocar un riesgo de descarga
• El acondicionador de aire no está diseñado para eléctrica.
que lo usen niños pequeños. Los niños pequeños • No utilice este u otro artefacto eléctrico si huele
deben estar siempre bajo control para asegurar gas. Puede provocar un riesgo de incendio o
que no jueguen o se cuelguen del acondicionador explosión.
de aire. • Apague y desenchufe el acondicionador de aire
• Asegúrese de quitar todos los materiales de antes de limpiarlo para evitar el riesgo de una
empaque del acondicionador de aire antes de descarga eléctrica.
usarlo. Puede provocar lesiones personales. • No limpie la unidad con agua. El agua puede
• No desarme o modifique el acondicionador de aire ingresar a la unidad y dañar la aislación, creando
o el cable de energía. Puede provocar un riesgo de así un peligro de descarga eléctrica. Si ingresa
descarga eléctrica o incendio. agua a la unidad, desenchúfela de inmediato y
• No coloque el cable de energía o acondicionador comuníquese con el Servicio de atención al cliente.
de aire cerca de un calentador, radiador, u otra Puede provocar un riesgo de descarga eléctrica.
fuente de calor. Puede provocar un riesgo de • Utilice dos o más personas para levantar e instalar
descarga eléctrica o incendio. la unidad. No hacerlo puede provocar lesiones en
• No use este u otro artefacto cerca de gases o la espalda u otras lesiones.
líquidos inflamables u otros combustibles, tales
como gasolina, benceno, solvente, etc. Puede
provocar un riesgo de descarga eléctrica o
incendio. 25
INSTRUCCIONES DE SEGURIDAD IMPORTANTES
LEA TODAS LAS INSTRUCCIONES ANTES DE USAR
PRECAUCIONES BÁSICAS DE SEGURIDAD
PRECAUCIÓN Para reducir el riesgo de incendio, descarga eléctrica o
lesiones personales al usar este artefacto, siga las precauciones básicas, incluyendo
las siguientes:
• Para evitar posibles cortes, evite el contacto con las • Cierre todas las puertas y ventanas de la habitación para
piezas metálicas del acondicionador de aire cuando una operación más efectiva.
quite o vuelva a instalar el filtro. Puede provocar un
riesgo de lesiones personales. • Para evitar daños al acabado de la superficie, utilice sólo
un paño suave para limpiar el acondicionador de aire. No
utilice cera, solvente, o un detergente fuerte.
• No bloquee la toma o salida de aire del acondicionador
de aire. Una corriente de aire reducida provocará un • Para evitar derrames y daños a la propiedad, asegúrese
desempeño pobre y podría dañar la unidad. de drenar el acondicionador de aire correctamente.
• Siempre tome el enchufe cuando enchufe o desenchufe • Para evitar que las serpentinas se congelen, no opere el
el acondicionador de aire. Nunca desenchufe tirando del acondicionador de aire si la temperatura de la habitación
cable. Puede provocar un riesgo de descarga eléctrica y se encuentra por debajo de 62°F (17°C).
daños.
• Siempre apague y desenchufe el acondicionador de aire • Este acondicionador de aire está diseñado para un uso
cuando no vaya a utilizarlo por períodos extensos. Esto . doméstico normal. No lo use para enfriar mascotas,
conserva la energía y reduce la posibilidad de accidentes alimentos, maquinaria de precisión
u objetos de arte.
• Ajuste las ruedas con trabas para evitar que
acondicionador de aire se deslice en pisos lisos. • No beba el agua del depósito de drenaje. Elimínela en el
exterior o en el desagüe.
• Instale el acondicionador de aire sobre un piso resistente • No opere el acondicionador de aire sin el filtro en su
y nivelado que pueda soportar hasta 110 lbs (50 kg). La lugar. El funcionamiento sin el filtro puede dañar la
instalación sobre un piso débil o desparejo puede unidad.
provocar un riesgo para la propiedad y lesiones
personales. • Limpie el filtro cada dos semanas, o más a menudo si
hiciera falta.
• Verifique que el acondicionador de aire sea del tamaño
adecuado para el área que desea enfriar. Usar un
acondicionador de aire de un tamaño incorrecto puede
malgastar energía y dañar el artefacto.
SEGURIDAD ELÉCTRICA
ADVERTENCIA
• Este acondicionador de aire debe conectarse
en un tomacorriente con conexión a tierra de
60 Hz, 120 VAC protegido por una fusible de
Peligro de descarga eléctrica acción retardada de 15 amperes o un
No seguir estas instrucciones puede provocar disyuntor.
la muerte, un incendio o una descarga • Este acondicionador de aire debe instalarse
eléctrica. de acuerdo con los códigos nacionales de
• Esta unidad debe contar con una adecuada cableado.
conexión a tierra. • No altere o modifique el enchufe o cable
• Bajo ninguna circunstancia corte o quite la de este acondicionador de aire. Si el cable
pata de conexión a tierra. de energía se gasta o daña, sólo un técnico
calificado puede cambiarlo utilizando piezas
• Si no cuenta con un tomacorriente con una de repuesto genuinas.
adecuada conexión, o si existe alguna duda • No utilice un cable de extensión.
sobre el mismo, un electricista calificado
debe verificar el tomacorriente o el circuito, y
si fuese necesario, instalar un tomacorriente
con adecuada conexión.
26
INSTRUCCIONES DE SEGURIDAD IMPORTANTES
SEGURIDAD ELÉCTRICA
Español
Para conexiones temporales, use solo un
adaptador listado UL. Verifique que la ranura
grande del adaptador esté alineada con la
ranura grande del tomacorriente.
Para evitar daños a la terminal de la conexión a Verifique que
tierra del adaptador, sostenga el adaptador en haya una
conexión a tierra
su lugar mientras enchufa o desenchufa el adecuada antes
acondicionador de aire. del uso.
• Conectar la terminal de la conexión a
tierra del adaptador al tornillo de la tapa
• Una conexión y desconexión frecuente
del tomacorriente de pared no conectará
pueden dañar la terminal de tierra del
el artefacto a tierra a menos que el
adaptador. Nunca utilice un adaptador
tornillo sea de metal y no aislado, y el
roto o dañado.
tomacorriente de pared esté conectado a
tierra a través del cableado doméstico.
27
PIEZAS Y CARACTERÍSTICAS
7 FILTRO DE AIRE
8 MANGUERA Y DIFUSOR
7
Utilice el difusor y la manguera para conectar el acondicionador
de aire al equipo de instalación de la ventana para enviar el
aire de salida hacia fuera.
28
CÓMO UTILIZAR EL ARTEFACTO
Español
IMPORTANTE:
• No permanezca frente a la corriente de aire del
acondicionador de aire por períodos largos.
• Para evitar el daño o lesión a mascotas o
plantas, constate que no estén expuestos a la
corriente directa del acondicionador de aire.
• Cuando lo use al mismo tiempo con cocinas,
chimeneas, u otros dispositivos de combustión,
asegúrese de que haya una suficiente corriente
de aire fresco en la habitación. NO lo use en
espacios muy cerrados con esta clase de
dispositivos.
• Este acondicionador de aire es para uso
doméstico como un artefacto de confort para
el consumidor. NO lo use como un sistema
de control preciso de clima, o para enfriar
equipamientos de precisión, alimentos,
mascotas, plantas, obras de arte, etc. Dichos
elementos podrían dañarse.
• No doble el tubo flexible hacia abajo si no
dispone del conjunto de instalación de la
ventana. Se puede dañar el sistema de aire
acondicionado o se puede deteriorar su
funcionamiento.
29
CÓMO UTILIZAR EL ARTEFACTO
PRECAUCIÓN
• Si entra líquido de las pilas en contacto con la piel o ropa, lávela inmediatamente con agua.
No utilice el control remoto si las pilas tienen fugas.
• Si el líquido de las pilas alcanzara su boca, cepille sus dientes y consulte a un médico.
Los productos químicos de las pilas podrían causar quemaduras u otros perjuicios a la salud.
30
CÓMO UTILIZAR EL ARTEFACTO
Dry
3 Dry
2
9
7 88
8
4 11
4 3 5 2 1
Español
tales como Modo,COOL(REFRIGERACIÓN), DRY de un tiempo de espera de hasta 24 horas. En la
(SECADO), FAN (VENTILADOR),se conservarán en la pantalla podrá verse 0. Utilice los botones para
memoria.Cuando se encienda después de estar ajustar el tiempo de espera de 1 a 24 horas, en
desenchufado, el acondicionador de aire volverá a incrementos de una hora.Para establecer un modo
configurarse en el Modo COOL(REFRIGERACIÓN). del apagado de retraso,apriete el botón TIMER
Cualquier clase de configuración deberá volver a (temporizador) cuando el aire acondicionado está
ingresarse. trabajando y marque los botones para ajustar
la demora. El air acondicionado se ap agará
2 MODE (Modo) automáticamente después de estar establecida ésta.
Apriete el botón MODO para elegir el modo de Para establecer un retraso automático, apriete el botón
funcionamiento COOL(REFRIGERACIÓN), DRY TIMER (temporizador) cuando el aire acondicionado
(SECADO), FAN (VENTILADOR)por el aire acondicionado. está apagado y use los botones para ajustar el
Y usted puede ver el modo activo a través de la Pantalla . tiempo de retraso.
El valor pre-establecido es REFRIGERACIÓN. Marque el La pantalla va a mostrar cuántas horas quedan hasta
botón MODO para cambiar al modo de DRY (SECADO), que la unidad se vaya a encender. El aire acondicionado
y hagalo una otra vez para cambiar al FAN (VENTILADOR) va a encender automaticamente después de la demora
una vez más para cambiar al COOL(REFRIGERACIÓN). establecida.Si quiere usted conocer cuántas horas ha
establecida, apriete el botónTIMER (temporizador) y
3 FAN(Ventilador) entonces puedever el tiempo mostrado en la pantalla LED.
Presionando el botón FAN SPEED la velocidad del Siquiere cambiar el tiempo establecido, marque el botón
ventilador de circulación pasa de baja a alta En la TIMER (temporizador) y ajustelo cuando el número está
pantalla podrá verse la velocidad de ventilador centellando.
seleccionada. La función puede utilizarse en los modos Para cancelar la función Temporizador, es una manera
COOL(REFRIGERACIÓN) o FAN (VENTILADOR) . apretar el botón TIMER (temporizador) y ajustar el número
Cuando se cambian las velocidades del ventilador, se hasta 0 cuando el número está entrellando, y la misma
produce una pequeña demora antes de que el motor las función va a cancelarse en unos segundos. Una mejor
modifique. manera es apretar el botón TIMER (temporizador) y
hacerlo de nuevo cuando el número está aún entrellando.
31
CÓMO UTILIZAR EL ARTEFACTO
Dry
3 Dry
2
9
7 88
8
4 11
4 3 5 2 1
El uso de funciones es el mismo cuando utilice el control remoto
o el panel de control, a menos que se indique lo contrario.
NOTE:
El sensor remoto se encuentra debajo de la descarga de aire y
de arriba del panel frontal.Siempre apunte el control remoto al
sensor.El control remoto puede no funcionar si el sensor se
encuentra cerca de luces brillantes o si el camino entre el
control remoto y el sensor está bloqueado.
5 TEMP/TIMER / 7 MODO DE SUSPENSIÓN
(temperatura/temporizador) Al establecer el modo de suspención, la temperatura va
En los modos COOL(REFRIGERACIÓN), y DRY(SECADO), a subir 1 °F después de 2 horas, y otras 2 horas
los botones / modifican la temperatura desde 86°F después, 1 °F más.
hasta 60°F, en incrementos de un grado. La temperatura se
mide en grados Fahrenheit.
No puede cambiarse a grados 8 °C/°F(BOTÓN DE CAMBIO ENTRE
Celsius.TIMER (temporizador), utilice los botones / CELSIU Y FAHRENHEIT
para ajustar el tiempo de demora de 1 a 24 horas, en
incrementos de una hora. Si presiona y sostiene los botones °C/°F función sólo se activa con el control remoto.
/ , la temperatura configurada o tiempo se modificarán Cuando la temperatura mostrada es °C (o °F), puede
automáticamente después de unos segundos. apretar el botón para cambiar el °F(o °C) .
NOTA: La temperatura de la pantalla es la CONFIGURADA,
no la temperatura de la habitación. En los modos COOL
(REFRIGERACIÓN) o DRY(SECADO) el termostato del 9 CONTINUO
acondicionador de aire hará funcionar al compresor hasta
alcanzar la temperatura configurada, luego encenderá o Después de estabalecer el modo de poderío, la unidad
apagará el compresor para mantener la temperatura va a seguir funcionando sin importar qué temperatura se
configurada. ajuste.
6 PANTALLA LED
La pantalla digital muestra la temperatura configurada
en grados Fahrenheit, la velocidad del ventilador, o la
programación de temporizador (TIMER) seleccionada.
Los indicadores se encenderán para mostrar el modo
activado y las configuraciones adicionales. El indicador
WATER FULL (lleno de agua) se encenderá para indicar
que el tanque interno de drenaje de agua debe vaciarse.
32
INSTRUCCIONES DE INSTALACIÓN
Español
Extensión y panel
de ventilación
Panel de
extensión
grande
Equipo de instalación en
ventanas (incluye 2 panel
de ventilación para
ventanas y 2 paneles de
extensión)
33
INSTRUCCIONES DE INSTALACIÓN
ADVERTENCIA
La longitud del tubo de escape es designado especialmente de acuerdo a las especificaciones
del producto. No lo sustituya ni prolongue con su manguera privada ya que esto podría causar
mal funcionamiento.
CÓMO CONECTAR LA MANGUERA Y EL DIFUSOR
UNL
OCK
CK
LO
34
INSTRUCCIONES DE INSTALACIÓN
Panel de Panel de
ventilación 18ʺ 181⁄4ʺ − 24ʺ
ventilación
Panel de Panel de
ventilación ventilación
Panel de extensión
18ʺ pequeño
181⁄4ʺ − 24ʺ
Para una abertura de ventana de 18ʺ, use el Para aberturas de ventana de 181⁄4ʺ a 24ʺ, utilice
panel de ventilación solo. el panel de ventilación y el panel de extensión
pequeño.
29ʺ − 36ʺ
24ʺ − 29ʺ
Español
Panel de Panel de
extensión extensión
grande grande
Panel de
Panel de ventilación Panel de
ventilación extensión
Panel de pequeño
ventilación
Panel de
extensión
24ʺ − 29ʺ 29ʺ − 36ʺ pequeño
Para aberturas de ventana de 24ʺ a 29ʺ, utilice Para aberturas de ventana de 29ʺ a 36ʺ, utilice
el panel de ventilación y el panel de extensión el panel de ventilación y ambos paneles de
grande. extensión.
Extensión y panel
de ventilación
Panel de
extensión
Extensión y panel 36" − 48" grande
de ventilación
Panel de Panel de
extensión ventilación
grande
Panel de
ventilación Panel de
extensión
pequeño
Panel de
extensión
pequeño
36" − 48"
INSTALACIÓN EN VENTANAS DE
DESLIZAMIENTO VERTICAL
NOTA: El equipo de instalación en ventanas puede utilizarse con ventanas de deslizamiento vertical de
un ancho de entre 18ʺ y 48ʺ.
Panel de
extensión (si fuera
necesario)
Panel de
ventilación
Sellante de espuma A
(Tipo adhesivo)
3 Baje la ventana con cuidado. Ajuste el panel 4 Corte la espuma B (tipo no adhesivo) según
de ventilación en su lugar con 4 tornillos tipo el ancho de la ventana. Rellene con la
A, más un tornillo por cada extensión. espuma B la separación existente entre el
Sólo panel de cristal y la ventana a fin de prevenir la
ventilación: 4 tornillos Tipo A entrada de aire o insectos en la habitación.
Panel de ventilación
y una extensión: 5 tornillos Tipo A
Panel de ventilación
y dos extensiones: 6 tornillos Tipo A
Dos paneles de
ventilación
y dos extensiones: 9 tornillos Tipo A
36
INSTRUCCIONES DE INSTALACIÓN
INSTALACIÓN EN VENTANAS DE
DESLIZAMIENTO VERTICAL
Soporte de seguridad
Tornillos
Tipo A
5 Instale el soporte de seguridad con un 6 Introduzca el extremo oval del difusor dentro
tornillo tipo A, como puede verse. del equipo de instalación en ventanas hasta
que las lengüetas queden trabadas.
Español
37
INSTRUCCIONES DE INSTALACIÓN
INSTALACIÓN EN VENTANAS DE
DESLIZAMIENTO HORIZONTAL
NOTA: El equipo de instalación de ventanas puede usarse con ventanas con bisagras con una altura
de 18ʺ a 48ʺ.
Sellado con
espuma C
(tipo adhesivo-
más corto) Panel de extensión
(si fuera necesario)
Sellado con
espuma A Panel de
(tipo adhesivo) ventilación
Tornillos Tipo A
3 Cierre la ventana con cuidado. Ajuste el 4 Corte la espuma B (tipo no adhesivo) según
panel de ventilación en su lugar con 4 el ancho de la ventana. Rellene con la
tornillos tipo A, más un tornillo por espuma B la separación existente entre el
cada extensión. cristal y la ventana a fin de prevenir la
Sólo panel de entrada de aire o insectos en la habitación.
ventilación: 4 tornillos Tipo A
Panel de ventilación
y una extensión: 5 tornillos Tipo A
Panel de ventilación
y dos extensiones: 6 tornillos Tipo A
Dos paneles de
ventilación y dos
extensiones: 9 tornillos Tipo A
38
INSTRUCCIONES DE INSTALACIÓN
INSTALACIÓN EN VENTANAS DE
DESLIZAMIENTO HORIZONTAL
Soporte de
seguridad
Tornillo Tipo A
Español
39
CUIDADO Y LIMPIE ZA
Su acondicionador de aire está diseñado para Para una eficiencia máxima, se recomienda que
funcionar durante todo el año con sólo una haga inspeccionar y limpiar las serpentinas de
limpieza y mantenimiento mínimos. enfriamiento una vez por año. Su Centro de
Servicio Autorizado LG local puede prestar
este servicio de inspección y limpieza por
ADVERTENCIA una módica suma.
• Desenchufe el acondicionador de aire antes de limpiar o realizar cualquier clase de mantenimiento
o arreglo.
• Tenga cuidado al limpiar las serpentinas o al quitar o volver a instalar el filtro: ¡las aletas de
enfriamiento son filosas!
No seguir estas precauciones puede provocar una descarga eléctrica o lesiones personales.
Drinaje de agua
Este producto tiene un sistema de auto-evaporación. El agua de condensación, se reciclará para
enfriar el condensador. Esto no sólo puede mejorar la eficiencia de enfriamiento, sino también
ahorrar energía para usted.
Empleando el puerto inferior de drenaje(solamente en Mode Sequedad)
• Esto se puede utilizar cuando se necesita deshumidificación de la humedad alta.
• Bajo los modos de FRESCO y Ventilación, no hace falta el drenaje de agua.
• Durante el modo de deshumidificación, quite el tapón de drenaje y la tubería de escape de la espalda de
la unidad.
• Instale un manguera de drenaje (diámetro interior 12mm [1/2"] ) y colo que el extremo abierto a una ubicación
adecuada de drenaje o al aire libre.
40
CUIDADO Y LIMPIEZA
Español
1
2 Use una aspiradora para limpiar el filtro. Si el
filtro está muy sucio, puede lavarse en agua
tibia utilizando un detergente suave.
No use limpiadores potentes o agua muy
caliente. No lo lave en el lavavajillas.
41
C UCI UD IADA
D OD OY LYIM
L IPMIPEIZE AZ A
42
DETECCIÓN DE PROBLEMAS
El aire El aire acondicionado esta Asegurese que ei aire acondicionado esta conectado
acondiciona do desconectado. completamente a la fuente de energia.
no enciende
El fusible esta quemado/el interruptor Cheque los fusibles/interruptor de la casa y reemplace
de energia se habloqueado. los fuslbles o reestablezca el interruptor de energia.
El dispositivo interruptor de corriente Presione el boton RESET situado en el enchufe del cable
esta desconectado. de alimentacion Si el boton RESET no p ermanece activo,
suspenda el uso del aure acondicionado y pongase en
contacto con un tecnico de servicio cualificado.
El aire El flujo de aire esta restringido. Asegurese que no haya cortinas,persianas o muebles
acondiciona do no bloqueando el frente del aire acondicionado.
enfr’a corno
debiera
Coloque el control de TEMPERATURA Ajustar el control de temperatura a un numero mas bajo.
en un numero mas alto.
El filtro de aire está sucio. Limipe el filtro pro lo menos cada dos semanas.Vea la
seccion de instrucciones de operacion.
El cuarto aun esta caliente. Cuando usted enciende el aire acondicionado debe esperar
un momento para que la habitacion se enftre.
El aire El hielo bloquea el flujo de aire y Elija el modo alto del ventilador High Fan o enfriado alto
acondiciona do detiene el enfriamiento del cuarto. High Cool .
enfria dernasiado
El acondicionador El área a enfriar es demasiado grande Consulte a su vendedor sobre la capacidad necesaria para
de aire funciona para el artefacto. enfriar el área deseada.
muy a menudo o
durant mucho Hay puertas o ventanas abiertas. Asegúrese de que puertas y ventanas estén cerradas.
tiempo
43
DETECCIÓN DE PROBLEMAS
Cotigo se
muestra en la
pantalla
FL El tanque de recolección de agua está Vacíe el tanque de recolección de agua. Ver la sección
lleno. Cuidado y limpieza.
44
Garantía
COBERTURA DE LA GARANTÍA:
LG Electronics Inc. (“LG”) garantiza que reparará o sustituirá, gratuitamente, su producto si resulta defectuoso en materiales o
mano de obra bajo condiciones normales de uso durante el periodo de garantía mencionado más abajo, efectivo a partir de
la fecha de compra del producto original por parte del consumidor. Esta garantía limitada sólo es válida para el comprador
original del producto y no es asignable ni transferible a ningún otro comprador o usuario final subsecuentes, y efectiva
únicamente cuando el producto se compra a través doe un distribuidor autorizado de LG y se utiliza en los Estados Unidos ("EE
UU") o en cualquiera de sus territorios.
Nota: Los recambios y piezas de repuesto pueden ser nuevos o estar reconstruidos de fábrica y están garantizados durante el
tiempo restante del periodo de garantía de la unidad original o noventa días (90), el periodo de los dos que sea más largo. Por
favor, guarde el recibo de compra o la nota de entrega como prueba de la fecha de compra como comprobante de garantía (se le
puede pedir que presente una copia a LG o a su representante autorizado).
PERIODO DE GARANTÍA:
1 año desde la fecha de compra: Cualquier repuesto interno/funcional y mano de obra
Español
5. Los daños o fallos ocasionados por el mal uso, abuso, 11. Las reparaciones cuando el producto se utiliza para
instalación inadecuada, reparación o mantenimiento. Se cualquier cosa fuera de lo normal y del uso doméstico
considera reparación inadecuada aquella en que se hayan habitual (por ejemplo su alquiler, uso comercial, en oficinas o
utilizado piezas no aprobadas o especificadas por LG. en instalaciones de ocio) o en contra de la instrucciones que
6. Los daños o averías causados por modificaciones no se indican en el manual del propietario.
autorizadas o alteraciones del producto. 12. La extracción y reinstalación del producto si está instalado
7. Los daños o averías causados por la utilización de una en un lugar inaccesible.
corriente eléctrica, tensión o código de plomería incorrectos.
ESTA GARANTÍA SE OTORGA EN SUSTITUCIÓN O EXCLUSIÓN DE TODA OTRA GARANTÍA, EXPRESA O IMPLÍCITA, INCLUYENDO SIN
LIMITAR CUALQUIER GARANTÍA DE CALIDAD O IDONEIDAD CON UN PROPÓSITO CONCRETO. EN LA MEDIDA EN QUE CUALQUIER
GARANTÍA IMPLÍCITA ES OBLIGADA POR LA LEY, ESTÁ LIMITADA EN DURACIÓN AL PERIODO DE GARANTÍA YA MENCIONADO. LA
REPARACIÓN O REEMPLAZO DE PIEZAS, SEGÚN LO ESTABLECIDO EN ESTA GARANTÍA, ES EL ÚNICO QUE PUEDE RECLAMAR EL
CLIENTE. NI EL FABRICANTE NI SU DISTRIBUIDOR EN LOS EE.UU. SE HACE RESPONSABLE DE CUALQUIER DAÑO (DERIVADO,
INDIRECTO, ESPECIAL O PENAL) DE CUALQUIER NATURALEZA, INCLUYENDO, SIN LIMITACION, LA PÉRDIDA DE INGRESOS O
BENEFICIOS O CUALQUIER OTRO TIPO DE DAÑO, AÚN BASADO EN UN CONTRATO, SEA UN AGRAVIO O DE CUALQUIER OTRA
MANERA.