You are on page 1of 617

Job No Sheet No Rev

BN/SS/-01 1
Part
Software licensed to BN
Job Title Design of Overhead Gantry Hoarding Truss - 30m Span Ref

By Biswajit Date06-Dec-18 Chd Biswajit


Client Suntony Signage File Final Gantry Truss-30m Date/Time
Span.std 07-Dec-2018 20:06

Job Information
Engineer Checked Approved

Name: Biswajit Biswajit


Date: 06-Dec-18 06-Dec-18

Comments
This design details are submitted for apporval and check.

Structure Type TRUSS

Number of Nodes 132 Highest Node 132


Number of Elements 415 Highest Beam 469

Number of Basic Load Cases 2


Number of Combination Load Cases 1

Included in this printout are data for:


All The Whole Structure

Included in this printout are results for load cases:


Type L/C Name

Primary 1 DL
Primary 2 WL
Combination 3 DL+WL

1000.000mm

27000.000mm

6500.000mm

1500.000mm

8500.000mm

Y
X
Z Load 3

Whole Structure (Input data was modified after picture taken)

Print Time/Date: 07/12/2018 20:09 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 1 of 617
Job No Sheet No Rev
BN/SS/-01 2
Part
Software licensed to BN
Job Title Design of Overhead Gantry Hoarding Truss - 30m Span Ref

By Biswajit Date06-Dec-18 Chd Biswajit


Client Suntony Signage File Final Gantry Truss-30m Date/Time
Span.std 07-Dec-2018 20:06

Section Properties
Prop Section Area Iyy Izz J Material
(cm2) (cm4) (cm4) (cm4)
1 PIP1016L 11.100 133.000 133.000 266.475 STEEL
2 PIP424L 3.250 6.460 6.460 12.929 STEEL
3 PIP483L 4.140 10.700 10.700 21.401 STEEL
4 PIP603L 5.230 21.600 21.600 43.185 STEEL
5 PIP2191H 39.500 2.25E+3 2.25E+3 4.49E+3 STEEL
6 PIP1524L 20.900 572.000 572.000 1.14E+3 STEEL
7 PIP889L 8.620 79.200 79.200 158.412 STEEL

Materials
Mat Name E ν Density α
(MPa) (kN/m3) (/°C)
1 STEEL 205E+3 0.300 76.820 12E -6
2 STAINLESSSTEEL 198E+3 0.300 76.820 18E -6
3 ALUMINUM 68.9E+3 0.330 26.602 23E -6
4 CONCRETE 21.7E+3 0.170 23.562 10E -6

Supports
Node X Y Z rX rY rZ
(kN/mm) (kN/mm) (kN/mm) (kN-m/deg) (kN-m/deg) (kN-m/deg)
1 Fixed Fixed Fixed - - -
2 Fixed Fixed Fixed - - -
17 Fixed Fixed Fixed - - -
18 Fixed Fixed Fixed - - -
101 - Fixed Fixed Fixed - -
102 - Fixed Fixed Fixed - -
117 - Fixed Fixed Fixed - -
118 - Fixed Fixed Fixed - -

Print Time/Date: 07/12/2018 20:09 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 2 of 617
Job No Sheet No Rev
BN/SS/-01 3
Part
Software licensed to BN
Job Title Design of Overhead Gantry Hoarding Truss - 30m Span Ref

By Biswajit Date06-Dec-18 Chd Biswajit


Client Suntony Signage File Final Gantry Truss-30m Date/Time
Span.std 07-Dec-2018 20:06

-1.59e+003 N
-1.59e+003 N
-1.59e+003 N
-1.59e+003 N
-1.59e+003 N
-1.59e+003 N -1.59e+003 N
-1.59e+003 N -1.59e+003 N
-1.59e+003 N -1.59e+003 N
-1.59e+003 N -1.59e+003 N
-1.59e+003 N -1.59e+003 N
-1.59e+003 N -1.59e+003 N
-1.59e+003 N -1.59e+003 N
-1.59e+003 N -1.59e+003 N
-1.59e+003 N -1.59e+003 N
-1.59e+003 N -1.59e+003 N
-1.59e+003 N -1.59e+003 N
-1.59e+003 N -1.59e+003 N
-1.59e+003 N -1.59e+003 N
-1.59e+003 N -1.59e+003 N
-1.59e+003 N -1.59e+003 N
-1.59e+003 N -1.59e+003 N
-1.59e+003 N
-1.59e+003 N
-1.59e+003 N
-1.59e+003 N
-1.59e+003 N

Y
X
Z Load 2

Whole Structure

Primary Load Cases


Number Name Type

1 DL Dead
2 WL Wind

Combination Load Cases


Comb. Combination L/C Name Primary Primary L/C Name Factor

3 DL+WL 1 DL 1.00
2 WL 1.00

Load Generators
There is no data of this type.

1 DL : Selfweight
Direction Factor Assigned Geometry

Y -1.050 ALL

Print Time/Date: 07/12/2018 20:09 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 3 of 617
Job No Sheet No Rev
BN/SS/-01 4
Part
Software licensed to BN
Job Title Design of Overhead Gantry Hoarding Truss - 30m Span Ref

By Biswajit Date06-Dec-18 Chd Biswajit


Client Suntony Signage File Final Gantry Truss-30m Date/Time
Span.std 07-Dec-2018 20:06

2 WL : Node Loads
Node FX FY FZ MX MY MZ
(kN) (kN) (kN) (kNm) (kNm) (kNm)
14 - - -1.587 - - -
16 - - -1.587 - - -
30 - - -1.587 - - -
32 - - -1.587 - - -
34 - - -1.587 - - -
36 - - -1.587 - - -
38 - - -1.587 - - -
40 - - -1.587 - - -
42 - - -1.587 - - -
44 - - -1.587 - - -
46 - - -1.587 - - -
48 - - -1.587 - - -
50 - - -1.587 - - -
52 - - -1.587 - - -
54 - - -1.587 - - -
56 - - -1.587 - - -
58 - - -1.587 - - -
60 - - -1.587 - - -
62 - - -1.587 - - -
64 - - -1.587 - - -
66 - - -1.587 - - -
68 - - -1.587 - - -
70 - - -1.587 - - -
72 - - -1.587 - - -
74 - - -1.587 - - -
76 - - -1.587 - - -
78 - - -1.587 - - -
80 - - -1.587 - - -
82 - - -1.587 - - -
84 - - -1.587 - - -
86 - - -1.587 - - -
88 - - -1.587 - - -
90 - - -1.587 - - -
92 - - -1.587 - - -
94 - - -1.587 - - -
96 - - -1.587 - - -
98 - - -1.587 - - -
100 - - -1.587 - - -
114 - - -1.587 - - -
116 - - -1.587 - - -
130 - - -1.587 - - -
132 - - -1.587 - - -

Print Time/Date: 07/12/2018 20:09 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 4 of 617
Job No Sheet No Rev
BN/SS/-01 5
Part
Software licensed to BN
Job Title Design of Overhead Gantry Hoarding Truss - 30m Span Ref

By Biswajit Date06-Dec-18 Chd Biswajit


Client Suntony Signage File Final Gantry Truss-30m Date/Time
Span.std 07-Dec-2018 20:06

5.290 mm
14.584 mm 4.842 mm
24.716 mm14.450 mm
34.600 mm24.607 mm
43.817 mm34.478 mm
52.030 mm 43.700 mm 4.383 mm
59.141 mm 51.889 mm 11.292 mm 2.622 mm
64.727 mm 59.004 mm 21.547 mm11.001 mmmm
68.933 mm 64.561 mm 31.343 mm21.193 mmmm 4.765
71.302 mm 68.770 mm 40.387 mm31.059 mm 9.374 2.707 mm
72.168 mm 71.113 mm 48.501 mm40.169 mm 8.4995.253
mm mm
71.101 mm 71.985 mm 55.218 mm 48.295 mm 7.867 mm2.898 mm
68.564 mm 70.898 mm 60.634 mm 55.043 mm
64.284 mm 60.450 mm 6.5115.625
mm mm
64.214 mm 68.377 mm
58.588 mm 64.022 mm 66.445 mm 64.115 mm 6.777 mm3.217 mm
51.484 mm 58.429 mm 66.699 mm 66.257 mm 4.9496.060
mm mm
51.347 mm 65.443 mm 66.517 mm 6.394 mm3.400 mm
43.451 mm 62.359 mm 65.238 mm
34.486 mm 43.376 mm 57.906 mm 62.159 mm 3.951 mm mm
6.207
25.093 mm 34.491 mm 51.925 mm 57.687 mm 6.237 mm3.655 mm
15.549 mm 25.213 mm 44.883 mm 51.718 mm 3.7086.403
mm mm
6.749 mm15.945 mm 36.836 mm 44.671 mm
7.558 mm 6.183 mm3.824 mm
28.216 mm 36.659 mm 3.626 mm
19.349 mm 28.070 mm
10.254 mm 19.306 mm
3.979 mm10.701 mm
4.304 mm
8.028 mm
3.216 mm8.138 mm
3.454 mm mm
5.912
2.339 mm5.938 mm
2.455 mm mm
3.895
1.517 mm3.935 mm
1.652 mm mm
2.210
0.957 mm2.148 mm
0.860 mm mm
0.643
Y
X 0.276 mm0.660 mm Load 3 : Displacement
Z 0.339 mm Displacement - mm

Whole Structure Displacements 0.1mm:1mm 3 DL+WL

Node Displacement Summary


Node L/C X Y Z Resultant rX rY rZ
(mm) (mm) (mm) (mm) (rad) (rad) (rad)
Max X 117 3:DL+WL 6.403 0.000 0.000 6.403 0.000 0.000 0.000
Min X 118 2:WL -5.173 0.000 0.000 5.173 0.000 0.000 0.000
Max Y 48 2:WL 2.347 1.930 -51.343 51.433 0.000 0.000 0.000
Min Y 63 3:DL+WL 0.146 -6.612 -70.792 71.101 0.000 0.000 0.000
Max Z 63 1:DL 0.696 -5.235 0.141 5.283 0.000 0.000 0.000
Min Z 68 2:WL -0.023 1.510 -71.916 71.932 0.000 0.000 0.000
Max rX 1 1:DL 0.000 0.000 0.000 0.000 0.000 0.000 0.000
Min rX 1 1:DL 0.000 0.000 0.000 0.000 0.000 0.000 0.000
Max rY 1 1:DL 0.000 0.000 0.000 0.000 0.000 0.000 0.000
Min rY 1 1:DL 0.000 0.000 0.000 0.000 0.000 0.000 0.000
Max rZ 1 1:DL 0.000 0.000 0.000 0.000 0.000 0.000 0.000
Min rZ 1 1:DL 0.000 0.000 0.000 0.000 0.000 0.000 0.000
Max Rst 67 3:DL+WL 0.591 -6.603 -71.863 72.168 0.000 0.000 0.000

Beam Displacement Detail Summary


Displacements shown in italic indicate the presence of an offset
Beam L/C d X Y Z Resultant
(mm) (mm) (mm) (mm) (mm)
Max X 389 3:DL+WL 1.08E+3 6.403 0.000 0.000 6.403
Min X 364 2:WL 1.08E+3 -5.172 0.000 0.000 5.172
Max Y 72 2:WL 1.8E+3 2.347 1.929 -51.343 51.433
Min Y 127 3:DL+WL 1.5E+3 0.146 -6.612 -70.792 71.101
Max Z 134 1:DL 900.000 0.698 -5.289 0.141 5.337
Min Z 144 2:WL 1.5E+3 -0.023 1.511 -71.916 71.932
Max Rst 141 3:DL+WL 1.5E+3 0.591 -6.603 -71.863 72.168

Print Time/Date: 07/12/2018 20:09 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 5 of 617
Job No Sheet No Rev
BN/SS/-01 6
Part
Software licensed to BN
Job Title Design of Overhead Gantry Hoarding Truss - 30m Span Ref

By Biswajit Date06-Dec-18 Chd Biswajit


Client Suntony Signage File Final Gantry Truss-30m Date/Time
Span.std 07-Dec-2018 20:06

Beam End Displacement Summary


Displacements shown in italic indicate the presence of an offset
Beam Node L/C X Y Z Resultant
(mm) (mm) (mm) (mm)
Max X 389 117 3:DL+WL 6.403 0.000 0.000 6.403
Min X 364 118 2:WL -5.172 0.000 0.000 5.172
Max Y 72 48 2:WL 2.347 1.929 -51.343 51.433
Min Y 127 63 3:DL+WL 0.146 -6.612 -70.792 71.101
Max Z 128 64 1:DL 0.698 -5.295 0.141 5.343
Min Z 144 68 2:WL -0.023 1.511 -71.916 71.932
Max Rst 141 67 3:DL+WL 0.591 -6.603 -71.863 72.168

Beam End Force Summary


The signs of the forces at end B of each beam have been reversed. For example: this means that the Min Fx entry gives the largest tension value for
an beam.
Axial Shear Torsion Bending
Beam Node L/C Fx Fy Fz Mx My Mz
(kN) (kN) (kN) (kNm) (kNm) (kNm)
Max Fx 354 101 3:DL+WL 203.425 -0.000 -0.000 -0.000 -0.000 -0.000
Min Fx 359 104 2:WL -189.735 0.000 0.000 0.000 0.000 0.000
Max Fy 390 111 1:DL -0.664 0.126 0.000 0.000 0.000 0.000
Min Fy 390 127 1:DL -0.664 -0.126 -0.000 -0.000 -0.000 -0.000
Max Fz 3 13 1:DL 0.301 0.013 0.000 0.000 0.000 0.000
Min Fz 3 13 1:DL 0.301 0.013 0.000 0.000 0.000 0.000
Max Mx 3 13 1:DL 0.301 0.013 0.000 0.000 0.000 0.000
Min Mx 3 13 1:DL 0.301 0.013 0.000 0.000 0.000 0.000
Max My 3 13 1:DL 0.301 0.013 0.000 0.000 0.000 0.000
Min My 3 13 1:DL 0.301 0.013 0.000 0.000 0.000 0.000
Max Mz 3 13 1:DL 0.301 0.013 0.000 0.000 0.000 0.000
Min Mz 3 13 1:DL 0.301 0.013 0.000 0.000 0.000 0.000

Beam Force Detail Summary


Sign convention as diagrams:- positive above line, negative below line except Fx where positive is compression. Distance d is given from beam end A.
Axial Shear Torsion Bending
Beam L/C d Fx Fy Fz Mx My Mz
(mm) (kN) (kN) (kN) (kNm) (kNm) (kNm)
Max Fx 354 3:DL+WL 1.08E+3 203.425 -0.000 -0.000 -0.000 -0.000 -0.000
Min Fx 359 2:WL 0.000 -189.735 0.000 0.000 0.000 0.000 0.000
Max Fy 390 1:DL 0.000 -0.664 0.126 0.000 0.000 0.000 0.000
Min Fy 390 1:DL 1.5E+3 -0.664 -0.126 -0.000 -0.000 -0.000 -0.000
Max Fz 3 1:DL 0.000 0.301 0.013 0.000 0.000 0.000 0.000
Min Fz 3 1:DL 0.000 0.301 0.013 0.000 0.000 0.000 0.000
Max Mx 3 1:DL 0.000 0.301 0.013 0.000 0.000 0.000 0.000
Min Mx 3 1:DL 0.000 0.301 0.013 0.000 0.000 0.000 0.000
Max My 3 1:DL 0.000 0.301 0.013 0.000 0.000 0.000 0.000
Min My 3 1:DL 0.000 0.301 0.013 0.000 0.000 0.000 0.000
Max Mz 3 1:DL 0.000 0.301 0.013 0.000 0.000 0.000 0.000

Print Time/Date: 07/12/2018 20:09 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 6 of 617
Job No Sheet No Rev
BN/SS/-01 7
Part
Software licensed to BN
Job Title Design of Overhead Gantry Hoarding Truss - 30m Span Ref

By Biswajit Date06-Dec-18 Chd Biswajit


Client Suntony Signage File Final Gantry Truss-30m Date/Time
Span.std 07-Dec-2018 20:06

Beam Force Detail Summary Cont...


Axial Shear Torsion Bending
Beam L/C d Fx Fy Fz Mx My Mz
(mm) (kN) (kN) (kN) (kNm) (kNm) (kNm)
Min Mz 3 1:DL 0.000 0.301 0.013 0.000 0.000 0.000 0.000

Reactions
Horizontal Vertical Horizontal Moment
Node L/C FX FY FZ MX MY MZ
(kN) (kN) (kN) (kNm) (kNm) (kNm)
1 1:DL 0.448 -2.321 -0.183 0.000 0.000 0.000
2:WL 24.632 115.915 -3.414 0.000 0.000 0.000
3:DL+WL 25.079 113.594 -3.597 0.000 0.000 0.000
2 1:DL 0.220 -2.518 0.229 0.000 0.000 0.000
2:WL -21.545 -114.514 -3.758 0.000 0.000 0.000
3:DL+WL -21.325 -117.032 -3.529 0.000 0.000 0.000
17 1:DL -0.223 16.201 1.072 0.000 0.000 0.000
2:WL 8.549 150.155 22.101 0.000 0.000 0.000
3:DL+WL 8.327 166.355 23.173 0.000 0.000 0.000
18 1:DL -0.445 16.299 -1.109 0.000 0.000 0.000
2:WL -11.636 -151.700 20.009 0.000 0.000 0.000
3:DL+WL -12.081 -135.401 18.900 0.000 0.000 0.000
101 1:DL 0.000 15.608 1.027 0.000 0.000 0.000
2:WL 0.000 207.402 16.944 0.000 0.000 0.000
3:DL+WL 0.000 223.010 17.972 0.000 0.000 0.000
102 1:DL 0.000 15.514 -1.090 0.000 0.000 0.000
2:WL 0.000 -206.051 15.061 0.000 0.000 0.000
3:DL+WL 0.000 -190.536 13.971 0.000 0.000 0.000
117 1:DL 0.000 -1.895 -0.120 0.000 0.000 0.000
2:WL 0.000 26.433 -0.179 0.000 0.000 0.000
3:DL+WL 0.000 24.538 -0.298 0.000 0.000 0.000
118 1:DL 0.000 -1.703 0.173 0.000 0.000 0.000
2:WL 0.000 -27.640 -0.111 0.000 0.000 0.000
3:DL+WL 0.000 -29.343 0.062 0.000 0.000 0.000

Print Time/Date: 07/12/2018 20:09 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 7 of 617
Job No Sheet No Rev
BN/SS/-01 8
Part
Software licensed to BN
Job Title Design of Overhead Gantry Hoarding Truss - 30m Span Ref

By Biswajit Date06-Dec-18 Chd Biswajit


Client Suntony Signage File Final Gantry Truss-30m Date/Time
Span.std 07-Dec-2018 20:06

Reaction Summary
Horizontal Vertical Horizontal Moment
Node L/C FX FY FZ MX MY MZ
(kN) (kN) (kN) (kNm) (kNm) (kNm)
Max FX 1 3:DL+WL 25.079 113.594 -3.597 0.000 0.000 0.000
Min FX 2 2:WL -21.545 -114.514 -3.758 0.000 0.000 0.000
Max FY 101 3:DL+WL 0.000 223.010 17.972 0.000 0.000 0.000
Min FY 102 2:WL 0.000 -206.051 15.061 0.000 0.000 0.000
Max FZ 17 3:DL+WL 8.327 166.355 23.173 0.000 0.000 0.000
Min FZ 2 2:WL -21.545 -114.514 -3.758 0.000 0.000 0.000
Max MX 1 1:DL 0.448 -2.321 -0.183 0.000 0.000 0.000
Min MX 1 1:DL 0.448 -2.321 -0.183 0.000 0.000 0.000
Max MY 1 1:DL 0.448 -2.321 -0.183 0.000 0.000 0.000
Min MY 1 1:DL 0.448 -2.321 -0.183 0.000 0.000 0.000
Max MZ 1 1:DL 0.448 -2.321 -0.183 0.000 0.000 0.000
Min MZ 1 1:DL 0.448 -2.321 -0.183 0.000 0.000 0.000

Reaction Envelope
Horizontal Vertical Horizontal Moment
Node Env FX FY FZ MX MY MZ
(kN) (kN) (kN) (kNm) (kNm) (kNm)
1 +ve 25.079 113.594 0.000 0.000 0.000 0.000
1 +ve Load: 3 Load: 3 - - - -
1 -ve 0.000 0.000 -3.597 0.000 0.000 0.000
1 -ve - - Load: 3 - - -
2 +ve 0.000 0.000 0.000 0.000 0.000 0.000
2 +ve - - - - - -
2 -ve -21.325 -117.032 -3.529 0.000 0.000 0.000
2 -ve Load: 3 Load: 3 Load: 3 - - -
17 +ve 8.327 166.355 23.173 0.000 0.000 0.000
17 +ve Load: 3 Load: 3 Load: 3 - - -
17 -ve 0.000 0.000 0.000 0.000 0.000 0.000
17 -ve - - - - - -
18 +ve 0.000 0.000 18.900 0.000 0.000 0.000
18 +ve - - Load: 3 - - -
18 -ve -12.081 -135.401 0.000 0.000 0.000 0.000
18 -ve Load: 3 Load: 3 - - - -
101 +ve 0.000 223.010 17.972 0.000 0.000 0.000
101 +ve - Load: 3 Load: 3 - - -
101 -ve 0.000 0.000 0.000 0.000 0.000 0.000
101 -ve - - - - - -
102 +ve 0.000 0.000 13.971 0.000 0.000 0.000
102 +ve - - Load: 3 - - -
102 -ve 0.000 -190.536 0.000 0.000 0.000 0.000
102 -ve - Load: 3 - - - -
117 +ve 0.000 24.538 0.000 0.000 0.000 0.000
117 +ve - Load: 3 - - - -

Print Time/Date: 07/12/2018 20:09 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 8 of 617
Job No Sheet No Rev
BN/SS/-01 9
Part
Software licensed to BN
Job Title Design of Overhead Gantry Hoarding Truss - 30m Span Ref

By Biswajit Date06-Dec-18 Chd Biswajit


Client Suntony Signage File Final Gantry Truss-30m Date/Time
Span.std 07-Dec-2018 20:06

Reaction Envelope Cont...


Horizontal Vertical Horizontal Moment
Node Env FX FY FZ MX MY MZ
(kN) (kN) (kN) (kNm) (kNm) (kNm)
117 -ve 0.000 0.000 -0.298 0.000 0.000 0.000
117 -ve - - Load: 3 - - -
118 +ve 0.000 0.000 0.062 0.000 0.000 0.000
118 +ve - - Load: 3 - - -
118 -ve 0.000 -29.343 0.000 0.000 0.000 0.000
118 -ve - Load: 3 - - - -

Utilization Ratio
Beam Analysis Design Actual Allowable Ratio Clause L/C Ax Iz Iy Ix
Property Property Ratio Ratio (Act./Allow.) (cm2) (cm4) (cm4) (cm4)
3 PIP424L PIP424L 0.008 0.900 0.009 Sec. 9.3.1.3 2 3.250 6.460 6.460 12.920
4 PIP1016L PIP1016L 0.043 0.900 0.048 Sec. 7.1.2 2 11.100 133.000 133.000 266.000
5 PIP483L PIP483L 0.322 0.900 0.358 Sec. 9.3.2.2 2 4.140 10.700 10.700 21.400
7 PIP1016L PIP1016L 0.095 0.900 0.105 Sec. 6.2 3 11.100 133.000 133.000 266.000
8 PIP424L PIP424L 0.045 0.900 0.050 Sec. 6.2 2 3.250 6.460 6.460 12.920
9 PIP1016L PIP1016L 0.084 0.900 0.093 Sec. 7.1.2 2 11.100 133.000 133.000 266.000
10 PIP603L PIP603L 0.067 0.900 0.074 Sec. 6.2 2 5.230 21.600 21.600 43.200
12 PIP1016L PIP1016L 0.099 0.900 0.110 Sec. 6.2 2 11.100 133.000 133.000 266.000
13 PIP483L PIP483L 0.318 0.900 0.354 Sec. 7.1.2 1 4.140 10.700 10.700 21.400
14 PIP483L PIP483L 0.676 0.900 0.751 Sec. 7.1.2 3 4.140 10.700 10.700 21.400
15 PIP1016L PIP1016L 0.018 0.900 0.020 Sec. 6.2 1 11.100 133.000 133.000 266.000
16 PIP603L PIP603L 0.073 0.900 0.081 Sec. 7.1.2 2 5.230 21.600 21.600 43.200
18 PIP1016L PIP1016L 0.046 0.900 0.051 Sec. 6.2 3 11.100 133.000 133.000 266.000
19 PIP424L PIP424L 0.390 0.900 0.433 Sec. 7.1.2 2 3.250 6.460 6.460 12.920
20 PIP483L PIP483L 0.341 0.900 0.379 Sec. 7.1.2 3 4.140 10.700 10.700 21.400
21 PIP483L PIP483L 0.328 0.900 0.364 Sec. 6.2 2 4.140 10.700 10.700 21.400
22 PIP424L N/A 3.250 6.460 6.460 12.920
23 PIP1016L PIP1016L 0.226 0.900 0.251 Sec. 7.1.2 3 11.100 133.000 133.000 266.000
24 PIP603L PIP603L 0.263 0.900 0.292 Sec. 9.3.1.3 2 5.230 21.600 21.600 43.200
26 PIP1016L PIP1016L 0.094 0.900 0.104 Sec. 6.2 2 11.100 133.000 133.000 266.000
27 PIP483L PIP483L 0.185 0.900 0.205 Sec. 6.2 3 4.140 10.700 10.700 21.400
28 PIP483L PIP483L 0.406 0.900 0.452 Sec. 7.1.2 2 4.140 10.700 10.700 21.400
29 PIP1016L PIP1016L 0.038 0.900 0.043 Sec. 9.3.2.2 2 11.100 133.000 133.000 266.000
30 PIP603L PIP603L 0.191 0.900 0.212 Sec. 9.3.1.3 3 5.230 21.600 21.600 43.200
32 PIP1016L PIP1016L 0.045 0.900 0.050 Sec. 9.3.2.2 2 11.100 133.000 133.000 266.000
33 PIP424L PIP424L 0.028 0.900 0.031 Sec. 7.1.2 2 3.250 6.460 6.460 12.920
34 PIP483L PIP483L 0.232 0.900 0.258 Sec. 9.3.2.2 3 4.140 10.700 10.700 21.400
35 PIP483L PIP483L 0.120 0.900 0.133 Sec. 7.1.2 1 4.140 10.700 10.700 21.400
36 PIP424L PIP424L 0.005 0.900 0.005 Sec. 9.3.1.3 2 3.250 6.460 6.460 12.920
37 PIP1016L PIP1016L 0.019 0.900 0.021 Sec. 6.2 2 11.100 133.000 133.000 266.000
38 PIP603L PIP603L 0.301 0.900 0.334 Sec. 7.1.2 2 5.230 21.600 21.600 43.200
40 PIP1016L PIP1016L 0.066 0.900 0.073 Sec. 9.3.1.3 2 11.100 133.000 133.000 266.000
41 PIP483L PIP483L 0.124 0.900 0.137 Sec. 9.3.1.3 3 4.140 10.700 10.700 21.400

Print Time/Date: 07/12/2018 20:09 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 9 of 617
Job No Sheet No Rev
BN/SS/-01 10
Part
Software licensed to BN
Job Title Design of Overhead Gantry Hoarding Truss - 30m Span Ref

By Biswajit Date06-Dec-18 Chd Biswajit


Client Suntony Signage File Final Gantry Truss-30m Date/Time
Span.std 07-Dec-2018 20:06

Utilization Ratio Cont...


Beam Analysis Design Actual Allowable Ratio Clause L/C Ax Iz Iy Ix
Property Property Ratio Ratio (Act./Allow.) (cm2) (cm4) (cm4) (cm4)
42 PIP483L PIP483L 0.230 0.900 0.256 Sec. 9.3.2.2 2 4.140 10.700 10.700 21.400
43 PIP1016L PIP1016L 0.099 0.900 0.110 Sec. 6.2 2 11.100 133.000 133.000 266.000
44 PIP603L PIP603L 0.283 0.900 0.315 Sec. 7.1.2 3 5.230 21.600 21.600 43.200
46 PIP1016L PIP1016L 0.034 0.900 0.037 Sec. 9.3.2.2 3 11.100 133.000 133.000 266.000
47 PIP424L PIP424L 0.009 0.900 0.010 Sec. 9.3.1.3 2 3.250 6.460 6.460 12.920
48 PIP483L PIP483L 0.190 0.900 0.211 Sec. 7.1.2 3 4.140 10.700 10.700 21.400
49 PIP483L PIP483L 0.104 0.900 0.116 Sec. 9.3.2.2 1 4.140 10.700 10.700 21.400
50 PIP424L N/A 3.250 6.460 6.460 12.920
51 PIP1016L PIP1016L 0.042 0.900 0.046 Sec. 9.3.1.3 3 11.100 133.000 133.000 266.000
52 PIP603L PIP603L 0.173 0.900 0.192 Sec. 9.3.1.3 3 5.230 21.600 21.600 43.200
54 PIP1016L PIP1016L 0.105 0.900 0.117 Sec. 9.3.2.2 2 11.100 133.000 133.000 266.000
55 PIP483L PIP483L 0.102 0.900 0.113 Sec. 6.2 3 4.140 10.700 10.700 21.400
56 PIP483L PIP483L 0.174 0.900 0.193 Sec. 9.3.2.2 2 4.140 10.700 10.700 21.400
57 PIP1016L PIP1016L 0.088 0.900 0.098 Sec. 9.3.1.3 2 11.100 133.000 133.000 266.000
58 PIP603L PIP603L 0.179 0.900 0.199 Sec. 9.3.1.3 3 5.230 21.600 21.600 43.200
60 PIP1016L PIP1016L 0.190 0.900 0.212 Sec. 9.3.2.2 3 11.100 133.000 133.000 266.000
61 PIP424L PIP424L 0.028 0.900 0.031 Sec. 7.1.2 2 3.250 6.460 6.460 12.920
62 PIP483L PIP483L 0.154 0.900 0.171 Sec. 7.1.2 3 4.140 10.700 10.700 21.400
63 PIP483L PIP483L 0.087 0.900 0.097 Sec. 7.1.2 1 4.140 10.700 10.700 21.400
64 PIP424L PIP424L 0.022 0.900 0.024 Sec. 9.3.2.2 2 3.250 6.460 6.460 12.920
65 PIP1016L PIP1016L 0.187 0.900 0.208 Sec. 9.3.1.3 3 11.100 133.000 133.000 266.000
66 PIP603L PIP603L 0.206 0.900 0.229 Sec. 9.3.2.2 2 5.230 21.600 21.600 43.200
68 PIP1016L PIP1016L 0.118 0.900 0.131 Sec. 9.3.2.2 2 11.100 133.000 133.000 266.000
69 PIP483L PIP483L 0.081 0.900 0.090 Sec. 6.2 3 4.140 10.700 10.700 21.400
70 PIP483L PIP483L 0.142 0.900 0.158 Sec. 7.1.2 2 4.140 10.700 10.700 21.400
71 PIP1016L PIP1016L 0.211 0.900 0.235 Sec. 6.2 2 11.100 133.000 133.000 266.000
72 PIP603L PIP603L 0.233 0.900 0.259 Sec. 9.3.2.2 3 5.230 21.600 21.600 43.200
74 PIP1016L PIP1016L 0.191 0.900 0.213 Sec. 7.1.2 3 11.100 133.000 133.000 266.000
75 PIP424L PIP424L 0.004 0.900 0.004 Sec. 7.1.2 1 3.250 6.460 6.460 12.920
76 PIP483L PIP483L 0.145 0.900 0.161 Sec. 7.1.2 3 4.140 10.700 10.700 21.400
77 PIP483L PIP483L 0.078 0.900 0.087 Sec. 7.1.2 1 4.140 10.700 10.700 21.400
78 PIP424L N/A 3.250 6.460 6.460 12.920
79 PIP1016L PIP1016L 0.205 0.900 0.228 Sec. 9.3.1.3 3 11.100 133.000 133.000 266.000
80 PIP603L PIP603L 0.117 0.900 0.130 Sec. 6.2 3 5.230 21.600 21.600 43.200
82 PIP1016L PIP1016L 0.237 0.900 0.263 Sec. 7.1.2 2 11.100 133.000 133.000 266.000
83 PIP483L PIP483L 0.077 0.900 0.085 Sec. 6.2 3 4.140 10.700 10.700 21.400
84 PIP483L PIP483L 0.133 0.900 0.148 Sec. 7.1.2 2 4.140 10.700 10.700 21.400
85 PIP1016L PIP1016L 0.203 0.900 0.225 Sec. 9.3.1.3 2 11.100 133.000 133.000 266.000
86 PIP603L PIP603L 0.136 0.900 0.151 Sec. 6.2 2 5.230 21.600 21.600 43.200
88 PIP1016L PIP1016L 0.313 0.900 0.348 Sec. 7.1.2 3 11.100 133.000 133.000 266.000
89 PIP424L PIP424L 0.028 0.900 0.031 Sec. 7.1.2 2 3.250 6.460 6.460 12.920
90 PIP483L PIP483L 0.113 0.900 0.125 Sec. 9.3.2.2 3 4.140 10.700 10.700 21.400
91 PIP483L PIP483L 0.054 0.900 0.060 Sec. 9.3.2.2 1 4.140 10.700 10.700 21.400
92 PIP424L PIP424L 0.025 0.900 0.028 Sec. 7.1.2 2 3.250 6.460 6.460 12.920

Print Time/Date: 07/12/2018 20:09 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 10 of 617
Job No Sheet No Rev
BN/SS/-01 11
Part
Software licensed to BN
Job Title Design of Overhead Gantry Hoarding Truss - 30m Span Ref

By Biswajit Date06-Dec-18 Chd Biswajit


Client Suntony Signage File Final Gantry Truss-30m Date/Time
Span.std 07-Dec-2018 20:06

Utilization Ratio Cont...


Beam Analysis Design Actual Allowable Ratio Clause L/C Ax Iz Iy Ix
Property Property Ratio Ratio (Act./Allow.) (cm2) (cm4) (cm4) (cm4)
93 PIP1016L PIP1016L 0.302 0.900 0.335 Sec. 9.3.1.3 3 11.100 133.000 133.000 266.000
94 PIP603L PIP603L 0.128 0.900 0.143 Sec. 9.3.2.2 2 5.230 21.600 21.600 43.200
96 PIP1016L PIP1016L 0.246 0.900 0.273 Sec. 7.1.2 2 11.100 133.000 133.000 266.000
97 PIP483L PIP483L 0.058 0.900 0.064 Sec. 6.2 3 4.140 10.700 10.700 21.400
98 PIP483L PIP483L 0.122 0.900 0.135 Sec. 9.3.2.2 2 4.140 10.700 10.700 21.400
99 PIP1016L PIP1016L 0.292 0.900 0.325 Sec. 6.2 2 11.100 133.000 133.000 266.000
100 PIP603L PIP603L 0.167 0.900 0.185 Sec. 9.3.2.2 3 5.230 21.600 21.600 43.200
102 PIP1016L PIP1016L 0.312 0.900 0.347 Sec. 9.3.2.2 3 11.100 133.000 133.000 266.000
103 PIP424L PIP424L 0.005 0.900 0.006 Sec. 9.3.2.2 3 3.250 6.460 6.460 12.920
104 PIP483L PIP483L 0.114 0.900 0.127 Sec. 9.3.2.2 3 4.140 10.700 10.700 21.400
105 PIP483L PIP483L 0.052 0.900 0.058 Sec. 7.1.2 1 4.140 10.700 10.700 21.400
106 PIP424L N/A 3.250 6.460 6.460 12.920
107 PIP1016L PIP1016L 0.315 0.900 0.350 Sec. 6.2 3 11.100 133.000 133.000 266.000
108 PIP603L PIP603L 0.066 0.900 0.073 Sec. 6.2 3 5.230 21.600 21.600 43.200
110 PIP1016L PIP1016L 0.319 0.900 0.354 Sec. 9.3.2.2 2 11.100 133.000 133.000 266.000
111 PIP483L PIP483L 0.060 0.900 0.066 Sec. 6.2 3 4.140 10.700 10.700 21.400
112 PIP483L PIP483L 0.122 0.900 0.135 Sec. 9.3.2.2 2 4.140 10.700 10.700 21.400
113 PIP1016L PIP1016L 0.285 0.900 0.316 Sec. 9.3.1.3 2 11.100 133.000 133.000 266.000
114 PIP603L PIP603L 0.087 0.900 0.097 Sec. 6.2 2 5.230 21.600 21.600 43.200
116 PIP1016L PIP1016L 0.391 0.900 0.435 Sec. 7.1.2 3 11.100 133.000 133.000 266.000
117 PIP424L PIP424L 0.028 0.900 0.031 Sec. 7.1.2 2 3.250 6.460 6.460 12.920
118 PIP483L PIP483L 0.080 0.900 0.089 Sec. 7.1.2 3 4.140 10.700 10.700 21.400
119 PIP483L PIP483L 0.029 0.900 0.033 Sec. 9.3.1.3 2 4.140 10.700 10.700 21.400
120 PIP424L PIP424L 0.026 0.900 0.029 Sec. 7.1.2 2 3.250 6.460 6.460 12.920
121 PIP1016L PIP1016L 0.367 0.900 0.408 Sec. 6.2 3 11.100 133.000 133.000 266.000
122 PIP603L PIP603L 0.054 0.900 0.060 Sec. 7.1.2 2 5.230 21.600 21.600 43.200
124 PIP1016L PIP1016L 0.328 0.900 0.364 Sec. 7.1.2 2 11.100 133.000 133.000 266.000
125 PIP483L PIP483L 0.040 0.900 0.044 Sec. 9.3.1.3 3 4.140 10.700 10.700 21.400
126 PIP483L PIP483L 0.116 0.900 0.129 Sec. 7.1.2 2 4.140 10.700 10.700 21.400
127 PIP1016L PIP1016L 0.336 0.900 0.374 Sec. 6.2 2 11.100 133.000 133.000 266.000
128 PIP603L PIP603L 0.096 0.900 0.107 Sec. 9.3.2.2 3 5.230 21.600 21.600 43.200
130 PIP1016L PIP1016L 0.387 0.900 0.430 Sec. 9.3.2.2 3 11.100 133.000 133.000 266.000
131 PIP424L PIP424L 0.007 0.900 0.007 Sec. 7.1.2 3 3.250 6.460 6.460 12.920
132 PIP483L PIP483L 0.085 0.900 0.094 Sec. 9.3.2.2 3 4.140 10.700 10.700 21.400
133 PIP483L PIP483L 0.028 0.900 0.031 Sec. 9.3.1.3 2 4.140 10.700 10.700 21.400
134 PIP424L N/A 3.250 6.460 6.460 12.920
135 PIP1016L PIP1016L 0.376 0.900 0.418 Sec. 6.2 3 11.100 133.000 133.000 266.000
136 PIP603L PIP603L 0.016 0.900 0.017 Sec. 6.2 3 5.230 21.600 21.600 43.200
138 PIP1016L PIP1016L 0.357 0.900 0.397 Sec. 9.3.2.2 2 11.100 133.000 133.000 266.000
139 PIP483L PIP483L 0.044 0.900 0.049 Sec. 6.2 3 4.140 10.700 10.700 21.400
140 PIP483L PIP483L 0.123 0.900 0.136 Sec. 9.3.2.2 3 4.140 10.700 10.700 21.400
141 PIP1016L PIP1016L 0.329 0.900 0.365 Sec. 9.3.1.3 2 11.100 133.000 133.000 266.000
142 PIP603L PIP603L 0.038 0.900 0.042 Sec. 6.2 2 5.230 21.600 21.600 43.200
144 PIP1016L PIP1016L 0.421 0.900 0.468 Sec. 7.1.2 3 11.100 133.000 133.000 266.000

Print Time/Date: 07/12/2018 20:09 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 11 of 617
Job No Sheet No Rev
BN/SS/-01 12
Part
Software licensed to BN
Job Title Design of Overhead Gantry Hoarding Truss - 30m Span Ref

By Biswajit Date06-Dec-18 Chd Biswajit


Client Suntony Signage File Final Gantry Truss-30m Date/Time
Span.std 07-Dec-2018 20:06

Utilization Ratio Cont...


Beam Analysis Design Actual Allowable Ratio Clause L/C Ax Iz Iy Ix
Property Property Ratio Ratio (Act./Allow.) (cm2) (cm4) (cm4) (cm4)
145 PIP424L PIP424L 0.028 0.900 0.031 Sec. 7.1.2 2 3.250 6.460 6.460 12.920
146 PIP483L PIP483L 0.059 0.900 0.065 Sec. 9.3.2.2 2 4.140 10.700 10.700 21.400
147 PIP483L PIP483L 0.032 0.900 0.036 Sec. 6.2 3 4.140 10.700 10.700 21.400
148 PIP424L PIP424L 0.027 0.900 0.030 Sec. 7.1.2 2 3.250 6.460 6.460 12.920
149 PIP1016L PIP1016L 0.386 0.900 0.428 Sec. 6.2 3 11.100 133.000 133.000 266.000
150 PIP603L PIP603L 0.016 0.900 0.018 Sec. 6.2 3 5.230 21.600 21.600 43.200
152 PIP1016L PIP1016L 0.365 0.900 0.406 Sec. 9.3.2.2 2 11.100 133.000 133.000 266.000
153 PIP483L PIP483L 0.032 0.900 0.036 Sec. 6.2 2 4.140 10.700 10.700 21.400
154 PIP483L PIP483L 0.114 0.900 0.126 Sec. 7.1.2 2 4.140 10.700 10.700 21.400
155 PIP1016L PIP1016L 0.342 0.900 0.380 Sec. 9.3.1.3 2 11.100 133.000 133.000 266.000
156 PIP603L PIP603L 0.024 0.900 0.027 Sec. 7.1.2 3 5.230 21.600 21.600 43.200
158 PIP1016L PIP1016L 0.413 0.900 0.459 Sec. 9.3.2.2 3 11.100 133.000 133.000 266.000
159 PIP424L PIP424L 0.007 0.900 0.007 Sec. 7.1.2 3 3.250 6.460 6.460 12.920
160 PIP483L PIP483L 0.060 0.900 0.067 Sec. 7.1.2 2 4.140 10.700 10.700 21.400
161 PIP483L PIP483L 0.029 0.900 0.033 Sec. 6.2 3 4.140 10.700 10.700 21.400
162 PIP424L N/A 3.250 6.460 6.460 12.920
163 PIP1016L PIP1016L 0.391 0.900 0.434 Sec. 6.2 3 11.100 133.000 133.000 266.000
164 PIP603L PIP603L 0.055 0.900 0.061 Sec. 7.1.2 2 5.230 21.600 21.600 43.200
166 PIP1016L PIP1016L 0.352 0.900 0.391 Sec. 9.3.2.2 2 11.100 133.000 133.000 266.000
167 PIP483L PIP483L 0.033 0.900 0.037 Sec. 6.2 2 4.140 10.700 10.700 21.400
168 PIP483L PIP483L 0.171 0.900 0.190 Sec. 7.1.2 3 4.140 10.700 10.700 21.400
169 PIP1016L PIP1016L 0.334 0.900 0.372 Sec. 6.2 2 11.100 133.000 133.000 266.000
170 PIP603L PIP603L 0.021 0.900 0.023 Sec. 9.3.2.2 3 5.230 21.600 21.600 43.200
172 PIP1016L PIP1016L 0.402 0.900 0.446 Sec. 9.3.2.2 3 11.100 133.000 133.000 266.000
173 PIP424L PIP424L 0.028 0.900 0.031 Sec. 7.1.2 2 3.250 6.460 6.460 12.920
174 PIP483L PIP483L 0.057 0.900 0.064 Sec. 7.1.2 2 4.140 10.700 10.700 21.400
175 PIP483L PIP483L 0.044 0.900 0.049 Sec. 9.3.1.3 3 4.140 10.700 10.700 21.400
176 PIP424L PIP424L 0.027 0.900 0.030 Sec. 7.1.2 2 3.250 6.460 6.460 12.920
177 PIP1016L PIP1016L 0.357 0.900 0.397 Sec. 9.3.1.3 3 11.100 133.000 133.000 266.000
178 PIP603L PIP603L 0.066 0.900 0.074 Sec. 9.3.1.3 3 5.230 21.600 21.600 43.200
180 PIP1016L PIP1016L 0.361 0.900 0.401 Sec. 7.1.2 2 11.100 133.000 133.000 266.000
181 PIP483L PIP483L 0.081 0.900 0.090 Sec. 9.3.2.2 1 4.140 10.700 10.700 21.400
182 PIP483L PIP483L 0.158 0.900 0.175 Sec. 7.1.2 3 4.140 10.700 10.700 21.400
183 PIP1016L PIP1016L 0.309 0.900 0.343 Sec. 6.2 2 11.100 133.000 133.000 266.000
184 PIP603L PIP603L 0.036 0.900 0.040 Sec. 6.2 2 5.230 21.600 21.600 43.200
186 PIP1016L PIP1016L 0.390 0.900 0.434 Sec. 7.1.2 3 11.100 133.000 133.000 266.000
187 PIP424L PIP424L 0.005 0.900 0.006 Sec. 7.1.2 3 3.250 6.460 6.460 12.920
188 PIP483L PIP483L 0.057 0.900 0.064 Sec. 7.1.2 2 4.140 10.700 10.700 21.400
189 PIP483L PIP483L 0.041 0.900 0.046 Sec. 9.3.1.3 3 4.140 10.700 10.700 21.400
190 PIP424L N/A 3.250 6.460 6.460 12.920
191 PIP1016L PIP1016L 0.359 0.900 0.399 Sec. 6.2 3 11.100 133.000 133.000 266.000
192 PIP603L PIP603L 0.129 0.900 0.143 Sec. 7.1.2 2 5.230 21.600 21.600 43.200
194 PIP1016L PIP1016L 0.304 0.900 0.338 Sec. 7.1.2 2 11.100 133.000 133.000 266.000
195 PIP483L PIP483L 0.076 0.900 0.084 Sec. 9.3.2.2 1 4.140 10.700 10.700 21.400

Print Time/Date: 07/12/2018 20:09 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 12 of 617
Job No Sheet No Rev
BN/SS/-01 13
Part
Software licensed to BN
Job Title Design of Overhead Gantry Hoarding Truss - 30m Span Ref

By Biswajit Date06-Dec-18 Chd Biswajit


Client Suntony Signage File Final Gantry Truss-30m Date/Time
Span.std 07-Dec-2018 20:06

Utilization Ratio Cont...


Beam Analysis Design Actual Allowable Ratio Clause L/C Ax Iz Iy Ix
Property Property Ratio Ratio (Act./Allow.) (cm2) (cm4) (cm4) (cm4)
196 PIP483L PIP483L 0.214 0.900 0.238 Sec. 9.3.2.2 3 4.140 10.700 10.700 21.400
197 PIP1016L PIP1016L 0.302 0.900 0.335 Sec. 9.3.1.3 2 11.100 133.000 133.000 266.000
198 PIP603L PIP603L 0.092 0.900 0.102 Sec. 9.3.2.2 3 5.230 21.600 21.600 43.200
200 PIP1016L PIP1016L 0.334 0.900 0.371 Sec. 9.3.2.2 3 11.100 133.000 133.000 266.000
201 PIP424L PIP424L 0.028 0.900 0.031 Sec. 7.1.2 2 3.250 6.460 6.460 12.920
202 PIP483L PIP483L 0.053 0.900 0.059 Sec. 9.3.2.2 2 4.140 10.700 10.700 21.400
203 PIP483L PIP483L 0.054 0.900 0.060 Sec. 9.3.1.3 3 4.140 10.700 10.700 21.400
204 PIP424L PIP424L 0.026 0.900 0.029 Sec. 9.3.2.2 2 3.250 6.460 6.460 12.920
205 PIP1016L PIP1016L 0.281 0.900 0.312 Sec. 6.2 3 11.100 133.000 133.000 266.000
206 PIP603L PIP603L 0.117 0.900 0.130 Sec. 6.2 3 5.230 21.600 21.600 43.200
208 PIP1016L PIP1016L 0.312 0.900 0.347 Sec. 9.3.2.2 2 11.100 133.000 133.000 266.000
209 PIP483L PIP483L 0.129 0.900 0.144 Sec. 9.3.2.2 1 4.140 10.700 10.700 21.400
210 PIP483L PIP483L 0.204 0.900 0.226 Sec. 9.3.2.2 3 4.140 10.700 10.700 21.400
211 PIP1016L PIP1016L 0.238 0.900 0.264 Sec. 6.2 2 11.100 133.000 133.000 266.000
212 PIP603L PIP603L 0.085 0.900 0.094 Sec. 6.2 2 5.230 21.600 21.600 43.200
214 PIP1016L PIP1016L 0.320 0.900 0.355 Sec. 9.3.2.2 3 11.100 133.000 133.000 266.000
215 PIP424L PIP424L 0.003 0.900 0.004 Sec. 7.1.2 1 3.250 6.460 6.460 12.920
216 PIP483L PIP483L 0.049 0.900 0.054 Sec. 7.1.2 2 4.140 10.700 10.700 21.400
217 PIP483L PIP483L 0.052 0.900 0.058 Sec. 6.2 3 4.140 10.700 10.700 21.400
218 PIP424L N/A 3.250 6.460 6.460 12.920
219 PIP1016L PIP1016L 0.279 0.900 0.310 Sec. 9.3.1.3 3 11.100 133.000 133.000 266.000
220 PIP603L PIP603L 0.206 0.900 0.229 Sec. 9.3.2.2 2 5.230 21.600 21.600 43.200
222 PIP1016L PIP1016L 0.212 0.900 0.235 Sec. 7.1.2 2 11.100 133.000 133.000 266.000
223 PIP483L PIP483L 0.134 0.900 0.149 Sec. 7.1.2 1 4.140 10.700 10.700 21.400
224 PIP483L PIP483L 0.242 0.900 0.269 Sec. 7.1.2 3 4.140 10.700 10.700 21.400
225 PIP1016L PIP1016L 0.232 0.900 0.258 Sec. 6.2 2 11.100 133.000 133.000 266.000
226 PIP603L PIP603L 0.159 0.900 0.176 Sec. 7.1.2 3 5.230 21.600 21.600 43.200
228 PIP1016L PIP1016L 0.221 0.900 0.246 Sec. 9.3.2.2 3 11.100 133.000 133.000 266.000
229 PIP424L PIP424L 0.028 0.900 0.031 Sec. 7.1.2 2 3.250 6.460 6.460 12.920
230 PIP483L PIP483L 0.039 0.900 0.044 Sec. 6.2 1 4.140 10.700 10.700 21.400
231 PIP483L PIP483L 0.061 0.900 0.068 Sec. 6.2 3 4.140 10.700 10.700 21.400
232 PIP424L PIP424L 0.023 0.900 0.026 Sec. 7.1.2 2 3.250 6.460 6.460 12.920
233 PIP1016L PIP1016L 0.153 0.900 0.170 Sec. 9.3.1.3 3 11.100 133.000 133.000 266.000
234 PIP603L PIP603L 0.172 0.900 0.191 Sec. 6.2 3 5.230 21.600 21.600 43.200
236 PIP1016L PIP1016L 0.219 0.900 0.243 Sec. 7.1.2 2 11.100 133.000 133.000 266.000
237 PIP483L PIP483L 0.177 0.900 0.196 Sec. 9.3.2.2 1 4.140 10.700 10.700 21.400
238 PIP483L PIP483L 0.230 0.900 0.255 Sec. 9.3.2.2 3 4.140 10.700 10.700 21.400
239 PIP1016L PIP1016L 0.134 0.900 0.149 Sec. 9.3.1.3 2 11.100 133.000 133.000 266.000
240 PIP603L PIP603L 0.130 0.900 0.144 Sec. 9.3.1.3 2 5.230 21.600 21.600 43.200
242 PIP1016L PIP1016L 0.205 0.900 0.228 Sec. 7.1.2 3 11.100 133.000 133.000 266.000
243 PIP424L PIP424L 0.005 0.900 0.006 Sec. 6.2 2 3.250 6.460 6.460 12.920
244 PIP483L PIP483L 0.044 0.900 0.049 Sec. 9.3.1.3 1 4.140 10.700 10.700 21.400
245 PIP483L PIP483L 0.059 0.900 0.065 Sec. 9.3.1.3 3 4.140 10.700 10.700 21.400
246 PIP424L N/A 3.250 6.460 6.460 12.920

Print Time/Date: 07/12/2018 20:09 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 13 of 617
Job No Sheet No Rev
BN/SS/-01 14
Part
Software licensed to BN
Job Title Design of Overhead Gantry Hoarding Truss - 30m Span Ref

By Biswajit Date06-Dec-18 Chd Biswajit


Client Suntony Signage File Final Gantry Truss-30m Date/Time
Span.std 07-Dec-2018 20:06

Utilization Ratio Cont...


Beam Analysis Design Actual Allowable Ratio Clause L/C Ax Iz Iy Ix
Property Property Ratio Ratio (Act./Allow.) (cm2) (cm4) (cm4) (cm4)
247 PIP1016L PIP1016L 0.146 0.900 0.162 Sec. 9.3.1.3 3 11.100 133.000 133.000 266.000
248 PIP603L PIP603L 0.292 0.900 0.325 Sec. 7.1.2 3 5.230 21.600 21.600 43.200
250 PIP1016L PIP1016L 0.068 0.900 0.075 Sec. 7.1.2 2 11.100 133.000 133.000 266.000
251 PIP483L PIP483L 0.192 0.900 0.213 Sec. 7.1.2 1 4.140 10.700 10.700 21.400
252 PIP483L PIP483L 0.233 0.900 0.259 Sec. 7.1.2 3 4.140 10.700 10.700 21.400
253 PIP1016L PIP1016L 0.138 0.900 0.153 Sec. 9.3.1.3 3 11.100 133.000 133.000 266.000
254 PIP603L PIP603L 0.217 0.900 0.241 Sec. 7.1.2 2 5.230 21.600 21.600 43.200
256 PIP1016L PIP1016L 0.075 0.900 0.083 Sec. 7.1.2 2 11.100 133.000 133.000 266.000
257 PIP424L PIP424L 0.028 0.900 0.031 Sec. 7.1.2 2 3.250 6.460 6.460 12.920
258 PIP483L PIP483L 0.048 0.900 0.054 Sec. 9.3.1.3 3 4.140 10.700 10.700 21.400
259 PIP483L PIP483L 0.059 0.900 0.065 Sec. 9.3.1.3 3 4.140 10.700 10.700 21.400
260 PIP424L PIP424L 0.022 0.900 0.025 Sec. 9.3.2.2 3 3.250 6.460 6.460 12.920
261 PIP1016L PIP1016L 0.037 0.900 0.041 Sec. 7.1.2 3 11.100 133.000 133.000 266.000
262 PIP603L PIP603L 0.239 0.900 0.265 Sec. 9.3.1.3 2 5.230 21.600 21.600 43.200
264 PIP1016L PIP1016L 0.074 0.900 0.082 Sec. 9.3.2.2 3 11.100 133.000 133.000 266.000
265 PIP483L PIP483L 0.214 0.900 0.238 Sec. 7.1.2 3 4.140 10.700 10.700 21.400
266 PIP483L PIP483L 0.257 0.900 0.286 Sec. 7.1.2 1 4.140 10.700 10.700 21.400
267 PIP1016L PIP1016L 0.028 0.900 0.031 Sec. 6.2 3 11.100 133.000 133.000 266.000
268 PIP603L PIP603L 0.169 0.900 0.188 Sec. 9.3.1.3 3 5.230 21.600 21.600 43.200
270 PIP1016L PIP1016L 0.077 0.900 0.085 Sec. 9.3.2.2 2 11.100 133.000 133.000 266.000
271 PIP424L PIP424L 0.354 0.900 0.393 Sec. 9.3.2.2 2 3.250 6.460 6.460 12.920
272 PIP483L PIP483L 0.155 0.900 0.172 Sec. 7.1.2 1 4.140 10.700 10.700 21.400
273 PIP483L PIP483L 0.199 0.900 0.221 Sec. 9.3.2.2 3 4.140 10.700 10.700 21.400
274 PIP424L N/A 3.250 6.460 6.460 12.920
275 PIP1016L PIP1016L 0.014 0.900 0.016 Sec. 9.3.1.3 2 11.100 133.000 133.000 266.000
276 PIP603L PIP603L 0.058 0.900 0.064 Sec. 9.3.1.3 2 5.230 21.600 21.600 43.200
278 PIP1016L PIP1016L 0.017 0.900 0.019 Sec. 9.3.2.2 1 11.100 133.000 133.000 266.000
279 PIP483L PIP483L 0.489 0.900 0.543 Sec. 9.3.2.2 2 4.140 10.700 10.700 21.400
280 PIP483L PIP483L 0.256 0.900 0.285 Sec. 9.3.1.3 3 4.140 10.700 10.700 21.400
281 PIP1016L PIP1016L 0.045 0.900 0.050 Sec. 9.3.1.3 2 11.100 133.000 133.000 266.000
282 PIP603L PIP603L 0.166 0.900 0.185 Sec. 7.1.2 2 5.230 21.600 21.600 43.200
284 PIP1016L N/A 11.100 133.000 133.000 266.000
287 PIP424L PIP424L 0.076 0.900 0.085 Sec. 6.2 3 3.250 6.460 6.460 12.920
288 PIP1016L PIP1016L 0.001 0.900 0.002 Sec. 9.3.2.2 1 11.100 133.000 133.000 266.000
290 PIP483L PIP483L 0.597 0.900 0.663 Sec. 7.1.2 2 4.140 10.700 10.700 21.400
291 PIP1016L PIP1016L 0.073 0.900 0.081 Sec. 6.2 2 11.100 133.000 133.000 266.000
292 PIP424L PIP424L 0.102 0.900 0.114 Sec. 9.3.1.3 2 3.250 6.460 6.460 12.920
293 PIP483L PIP483L 0.749 0.900 0.832 Sec. 7.1.2 3 4.140 10.700 10.700 21.400
294 PIP483L PIP483L 0.130 0.900 0.144 Sec. 7.1.2 2 4.140 10.700 10.700 21.400
295 PIP483L PIP483L 0.042 0.900 0.046 Sec. 9.3.2.2 2 4.140 10.700 10.700 21.400
296 PIP483L PIP483L 0.031 0.900 0.034 Sec. 7.1.2 3 4.140 10.700 10.700 21.400
297 PIP483L PIP483L 0.007 0.900 0.008 Sec. 7.1.2 2 4.140 10.700 10.700 21.400
298 PIP483L PIP483L 0.026 0.900 0.029 Sec. 9.3.2.2 3 4.140 10.700 10.700 21.400
299 PIP483L PIP483L 0.008 0.900 0.009 Sec. 9.3.1.3 3 4.140 10.700 10.700 21.400

Print Time/Date: 07/12/2018 20:09 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 14 of 617
Job No Sheet No Rev
BN/SS/-01 15
Part
Software licensed to BN
Job Title Design of Overhead Gantry Hoarding Truss - 30m Span Ref

By Biswajit Date06-Dec-18 Chd Biswajit


Client Suntony Signage File Final Gantry Truss-30m Date/Time
Span.std 07-Dec-2018 20:06

Utilization Ratio Cont...


Beam Analysis Design Actual Allowable Ratio Clause L/C Ax Iz Iy Ix
Property Property Ratio Ratio (Act./Allow.) (cm2) (cm4) (cm4) (cm4)
300 PIP483L PIP483L 0.028 0.900 0.031 Sec. 9.3.2.2 3 4.140 10.700 10.700 21.400
301 PIP483L PIP483L 0.010 0.900 0.011 Sec. 9.3.1.3 3 4.140 10.700 10.700 21.400
302 PIP483L PIP483L 0.029 0.900 0.032 Sec. 9.3.2.2 3 4.140 10.700 10.700 21.400
303 PIP483L PIP483L 0.010 0.900 0.011 Sec. 6.2 3 4.140 10.700 10.700 21.400
304 PIP483L PIP483L 0.027 0.900 0.030 Sec. 9.3.2.2 3 4.140 10.700 10.700 21.400
305 PIP483L PIP483L 0.008 0.900 0.009 Sec. 6.2 3 4.140 10.700 10.700 21.400
306 PIP483L PIP483L 0.025 0.900 0.028 Sec. 7.1.2 3 4.140 10.700 10.700 21.400
307 PIP483L PIP483L 0.005 0.900 0.006 Sec. 7.1.2 2 4.140 10.700 10.700 21.400
308 PIP483L PIP483L 0.027 0.900 0.030 Sec. 7.1.2 3 4.140 10.700 10.700 21.400
309 PIP483L PIP483L 0.025 0.900 0.027 Sec. 7.1.2 2 4.140 10.700 10.700 21.400
310 PIP483L PIP483L 0.052 0.900 0.058 Sec. 7.1.2 2 4.140 10.700 10.700 21.400
311 PIP483L PIP483L 0.372 0.900 0.413 Sec. 9.3.2.2 3 4.140 10.700 10.700 21.400
320 PIP603L PIP603L 0.214 0.900 0.237 Sec. 9.3.2.2 2 5.230 21.600 21.600 43.200
321 PIP603L PIP603L 0.166 0.900 0.184 Sec. 7.1.2 3 5.230 21.600 21.600 43.200
322 PIP2191H PIP2191H 0.032 0.900 0.036 Sec. 9.3.1.3 2 39.500 2.25E+3 2.25E+3 4.49E+3
323 PIP2191H PIP2191H 0.026 0.900 0.029 Sec. 9.3.1.3 3 39.500 2.25E+3 2.25E+3 4.49E+3
324 PIP2191H PIP2191H 0.075 0.900 0.083 Sec. 9.3.1.3 3 39.500 2.25E+3 2.25E+3 4.49E+3
325 PIP2191H PIP2191H 0.013 0.900 0.015 Sec. 9.3.1.3 1 39.500 2.25E+3 2.25E+3 4.49E+3
326 PIP2191H PIP2191H 0.052 0.900 0.058 Sec. 9.3.1.3 3 39.500 2.25E+3 2.25E+3 4.49E+3
327 PIP2191H PIP2191H 0.016 0.900 0.017 Sec. 9.3.1.3 3 39.500 2.25E+3 2.25E+3 4.49E+3
328 PIP2191H PIP2191H 0.032 0.900 0.036 Sec. 9.3.1.3 2 39.500 2.25E+3 2.25E+3 4.49E+3
329 PIP2191H PIP2191H 0.040 0.900 0.044 Sec. 6.2 3 39.500 2.25E+3 2.25E+3 4.49E+3
330 PIP2191H PIP2191H 0.032 0.900 0.035 Sec. 9.3.1.3 2 39.500 2.25E+3 2.25E+3 4.49E+3
331 PIP2191H PIP2191H 0.087 0.900 0.097 Sec. 9.3.1.3 2 39.500 2.25E+3 2.25E+3 4.49E+3
332 PIP2191H PIP2191H 0.069 0.900 0.077 Sec. 9.3.1.3 2 39.500 2.25E+3 2.25E+3 4.49E+3
333 PIP2191H PIP2191H 0.125 0.900 0.139 Sec. 9.3.1.3 2 39.500 2.25E+3 2.25E+3 4.49E+3
334 PIP2191H PIP2191H 0.118 0.900 0.131 Sec. 9.3.1.3 2 39.500 2.25E+3 2.25E+3 4.49E+3
335 PIP2191H PIP2191H 0.072 0.900 0.080 Sec. 6.2 3 39.500 2.25E+3 2.25E+3 4.49E+3
336 PIP2191H PIP2191H 0.054 0.900 0.060 Sec. 6.2 3 39.500 2.25E+3 2.25E+3 4.49E+3
337 PIP2191H PIP2191H 0.109 0.900 0.121 Sec. 6.2 3 39.500 2.25E+3 2.25E+3 4.49E+3
338 PIP2191H PIP2191H 0.090 0.900 0.100 Sec. 9.3.1.3 3 39.500 2.25E+3 2.25E+3 4.49E+3
339 PIP2191H PIP2191H 0.123 0.900 0.137 Sec. 9.3.1.3 3 39.500 2.25E+3 2.25E+3 4.49E+3
340 PIP2191H PIP2191H 0.037 0.900 0.041 Sec. 9.3.1.3 3 39.500 2.25E+3 2.25E+3 4.49E+3
341 PIP2191H PIP2191H 0.144 0.900 0.160 Sec. 9.3.1.3 3 39.500 2.25E+3 2.25E+3 4.49E+3
342 PIP2191H PIP2191H 0.089 0.900 0.098 Sec. 9.3.1.3 3 39.500 2.25E+3 2.25E+3 4.49E+3
343 PIP2191H PIP2191H 0.195 0.900 0.217 Sec. 9.3.1.3 3 39.500 2.25E+3 2.25E+3 4.49E+3
344 PIP2191H PIP2191H 0.171 0.900 0.190 Sec. 9.3.1.3 3 39.500 2.25E+3 2.25E+3 4.49E+3
345 PIP2191H PIP2191H 0.103 0.900 0.115 Sec. 6.2 2 39.500 2.25E+3 2.25E+3 4.49E+3
346 PIP2191H PIP2191H 0.048 0.900 0.053 Sec. 6.2 2 39.500 2.25E+3 2.25E+3 4.49E+3
347 PIP2191H PIP2191H 0.154 0.900 0.171 Sec. 6.2 2 39.500 2.25E+3 2.25E+3 4.49E+3
348 PIP2191H PIP2191H 0.098 0.900 0.109 Sec. 9.3.1.3 2 39.500 2.25E+3 2.25E+3 4.49E+3
349 PIP2191H PIP2191H 0.161 0.900 0.178 Sec. 9.3.1.3 2 39.500 2.25E+3 2.25E+3 4.49E+3
350 PIP2191H PIP2191H 0.055 0.900 0.061 Sec. 9.3.1.3 3 39.500 2.25E+3 2.25E+3 4.49E+3
351 PIP2191H PIP2191H 0.136 0.900 0.151 Sec. 9.3.1.3 3 39.500 2.25E+3 2.25E+3 4.49E+3

Print Time/Date: 07/12/2018 20:09 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 15 of 617
Job No Sheet No Rev
BN/SS/-01 16
Part
Software licensed to BN
Job Title Design of Overhead Gantry Hoarding Truss - 30m Span Ref

By Biswajit Date06-Dec-18 Chd Biswajit


Client Suntony Signage File Final Gantry Truss-30m Date/Time
Span.std 07-Dec-2018 20:06

Utilization Ratio Cont...


Beam Analysis Design Actual Allowable Ratio Clause L/C Ax Iz Iy Ix
Property Property Ratio Ratio (Act./Allow.) (cm2) (cm4) (cm4) (cm4)
352 PIP2191H PIP2191H 0.137 0.900 0.152 Sec. 9.3.1.3 3 39.500 2.25E+3 2.25E+3 4.49E+3
353 PIP2191H PIP2191H 0.218 0.900 0.242 Sec. 9.3.1.3 3 39.500 2.25E+3 2.25E+3 4.49E+3
354 PIP2191H PIP2191H 0.236 0.900 0.262 Sec. 9.3.1.3 3 39.500 2.25E+3 2.25E+3 4.49E+3
355 PIP2191H PIP2191H 0.078 0.900 0.087 Sec. 9.3.1.3 2 39.500 2.25E+3 2.25E+3 4.49E+3
356 PIP2191H PIP2191H 0.078 0.900 0.087 Sec. 9.3.1.3 2 39.500 2.25E+3 2.25E+3 4.49E+3
357 PIP2191H PIP2191H 0.159 0.900 0.176 Sec. 9.3.1.3 2 39.500 2.25E+3 2.25E+3 4.49E+3
358 PIP2191H PIP2191H 0.159 0.900 0.176 Sec. 9.3.1.3 2 39.500 2.25E+3 2.25E+3 4.49E+3
359 PIP2191H PIP2191H 0.220 0.900 0.245 Sec. 6.2 2 39.500 2.25E+3 2.25E+3 4.49E+3
360 PIP2191H PIP2191H 0.039 0.900 0.044 Sec. 9.3.1.3 3 39.500 2.25E+3 2.25E+3 4.49E+3
361 PIP2191H PIP2191H 0.038 0.900 0.042 Sec. 6.2 3 39.500 2.25E+3 2.25E+3 4.49E+3
362 PIP2191H PIP2191H 0.037 0.900 0.041 Sec. 6.2 3 39.500 2.25E+3 2.25E+3 4.49E+3
363 PIP2191H PIP2191H 0.036 0.900 0.040 Sec. 6.2 3 39.500 2.25E+3 2.25E+3 4.49E+3
364 PIP2191H PIP2191H 0.035 0.900 0.038 Sec. 6.2 3 39.500 2.25E+3 2.25E+3 4.49E+3
365 PIP1524L PIP1524L 0.046 0.900 0.051 Sec. 6.2 3 20.900 572.000 572.000 1.14E+3
366 PIP1524L N/A 20.900 572.000 572.000 1.14E+3
367 PIP1524L PIP1524L 0.022 0.900 0.025 Sec. 6.2 3 20.900 572.000 572.000 1.14E+3
368 PIP1524L N/A 20.900 572.000 572.000 1.14E+3
369 PIP1524L N/A 20.900 572.000 572.000 1.14E+3
370 PIP1524L N/A 20.900 572.000 572.000 1.14E+3
371 PIP1524L N/A 20.900 572.000 572.000 1.14E+3
372 PIP1524L N/A 20.900 572.000 572.000 1.14E+3
373 PIP1524L N/A 20.900 572.000 572.000 1.14E+3
374 PIP1524L N/A 20.900 572.000 572.000 1.14E+3
375 PIP1524L N/A 20.900 572.000 572.000 1.14E+3
376 PIP1524L N/A 20.900 572.000 572.000 1.14E+3
377 PIP1524L N/A 20.900 572.000 572.000 1.14E+3
378 PIP1524L N/A 20.900 572.000 572.000 1.14E+3
379 PIP1524L N/A 20.900 572.000 572.000 1.14E+3
380 PIP1524L N/A 20.900 572.000 572.000 1.14E+3
381 PIP1524L PIP1524L 0.008 0.900 0.009 Sec. 7.1.2 3 20.900 572.000 572.000 1.14E+3
382 PIP1524L PIP1524L 0.019 0.900 0.021 Sec. 7.1.2 2 20.900 572.000 572.000 1.14E+3
383 PIP1524L PIP1524L 0.044 0.900 0.049 Sec. 7.1.2 2 20.900 572.000 572.000 1.14E+3
384 PIP1524L PIP1524L 0.048 0.900 0.054 Sec. 7.1.2 2 20.900 572.000 572.000 1.14E+3
385 PIP2191H PIP2191H 0.032 0.900 0.036 Sec. 9.3.1.3 2 39.500 2.25E+3 2.25E+3 4.49E+3
386 PIP2191H PIP2191H 0.032 0.900 0.036 Sec. 9.3.1.3 2 39.500 2.25E+3 2.25E+3 4.49E+3
387 PIP2191H PIP2191H 0.031 0.900 0.035 Sec. 9.3.1.3 2 39.500 2.25E+3 2.25E+3 4.49E+3
388 PIP2191H PIP2191H 0.031 0.900 0.035 Sec. 9.3.1.3 2 39.500 2.25E+3 2.25E+3 4.49E+3
389 PIP2191H PIP2191H 0.031 0.900 0.034 Sec. 9.3.1.3 2 39.500 2.25E+3 2.25E+3 4.49E+3
390 PIP1524L PIP1524L 0.004 0.900 0.004 Sec. 6.2 3 20.900 572.000 572.000 1.14E+3
391 PIP1524L N/A 20.900 572.000 572.000 1.14E+3
392 PIP1524L PIP1524L 0.002 0.900 0.002 Sec. 9.3.2.2 2 20.900 572.000 572.000 1.14E+3
393 PIP1524L N/A 20.900 572.000 572.000 1.14E+3
394 PIP1524L N/A 20.900 572.000 572.000 1.14E+3
395 PIP1524L N/A 20.900 572.000 572.000 1.14E+3

Print Time/Date: 07/12/2018 20:09 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 16 of 617
Job No Sheet No Rev
BN/SS/-01 17
Part
Software licensed to BN
Job Title Design of Overhead Gantry Hoarding Truss - 30m Span Ref

By Biswajit Date06-Dec-18 Chd Biswajit


Client Suntony Signage File Final Gantry Truss-30m Date/Time
Span.std 07-Dec-2018 20:06

Utilization Ratio Cont...


Beam Analysis Design Actual Allowable Ratio Clause L/C Ax Iz Iy Ix
Property Property Ratio Ratio (Act./Allow.) (cm2) (cm4) (cm4) (cm4)
396 PIP1524L N/A 20.900 572.000 572.000 1.14E+3
397 PIP1524L N/A 20.900 572.000 572.000 1.14E+3
398 PIP1524L N/A 20.900 572.000 572.000 1.14E+3
399 PIP1524L N/A 20.900 572.000 572.000 1.14E+3
400 PIP1524L N/A 20.900 572.000 572.000 1.14E+3
401 PIP1524L N/A 20.900 572.000 572.000 1.14E+3
402 PIP1524L N/A 20.900 572.000 572.000 1.14E+3
403 PIP1524L N/A 20.900 572.000 572.000 1.14E+3
404 PIP1524L N/A 20.900 572.000 572.000 1.14E+3
405 PIP1524L N/A 20.900 572.000 572.000 1.14E+3
406 PIP1524L N/A 20.900 572.000 572.000 1.14E+3
407 PIP1524L PIP1524L 0.001 0.900 0.001 Sec. 7.1.2 3 20.900 572.000 572.000 1.14E+3
408 PIP1524L N/A 20.900 572.000 572.000 1.14E+3
409 PIP1524L PIP1524L 0.033 0.900 0.037 Sec. 9.3.2.2 2 20.900 572.000 572.000 1.14E+3
410 PIP889L PIP889L 0.158 0.900 0.176 Sec. 9.3.2.2 3 8.620 79.200 79.200 158.400
411 PIP889L PIP889L 0.083 0.900 0.092 Sec. 9.3.1.3 3 8.620 79.200 79.200 158.400
412 PIP889L PIP889L 0.153 0.900 0.170 Sec. 6.2 2 8.620 79.200 79.200 158.400
413 PIP889L PIP889L 0.078 0.900 0.086 Sec. 9.3.2.2 3 8.620 79.200 79.200 158.400
414 PIP889L PIP889L 0.254 0.900 0.282 Sec. 9.3.2.2 3 8.620 79.200 79.200 158.400
415 PIP889L PIP889L 0.219 0.900 0.244 Sec. 9.3.1.3 3 8.620 79.200 79.200 158.400
416 PIP889L PIP889L 0.254 0.900 0.282 Sec. 7.1.2 3 8.620 79.200 79.200 158.400
417 PIP889L PIP889L 0.219 0.900 0.244 Sec. 9.3.1.3 3 8.620 79.200 79.200 158.400
418 PIP889L PIP889L 0.254 0.900 0.282 Sec. 9.3.2.2 3 8.620 79.200 79.200 158.400
419 PIP889L PIP889L 0.219 0.900 0.244 Sec. 9.3.1.3 3 8.620 79.200 79.200 158.400
420 PIP889L PIP889L 0.254 0.900 0.282 Sec. 7.1.2 3 8.620 79.200 79.200 158.400
421 PIP889L PIP889L 0.219 0.900 0.244 Sec. 9.3.1.3 3 8.620 79.200 79.200 158.400
422 PIP889L PIP889L 0.013 0.900 0.014 Sec. 9.3.2.2 3 8.620 79.200 79.200 158.400
423 PIP889L PIP889L 0.013 0.900 0.014 Sec. 9.3.2.2 3 8.620 79.200 79.200 158.400
424 PIP889L PIP889L 0.007 0.900 0.007 Sec. 9.3.2.2 1 8.620 79.200 79.200 158.400
425 PIP889L PIP889L 0.007 0.900 0.007 Sec. 9.3.2.2 1 8.620 79.200 79.200 158.400
426 PIP889L PIP889L 0.000 0.900 0.000 Sec. 9.3.2.2 1 8.620 79.200 79.200 158.400
427 PIP889L PIP889L 0.000 0.900 0.000 Sec. 7.1.2 1 8.620 79.200 79.200 158.400
428 PIP889L PIP889L 0.000 0.900 0.000 Sec. 9.3.2.2 1 8.620 79.200 79.200 158.400
429 PIP889L PIP889L 0.000 0.900 0.000 Sec. 9.3.2.2 1 8.620 79.200 79.200 158.400
430 PIP889L PIP889L 0.000 0.900 0.000 Sec. 9.3.2.2 1 8.620 79.200 79.200 158.400
431 PIP889L PIP889L 0.000 0.900 0.000 Sec. 7.1.2 1 8.620 79.200 79.200 158.400
432 PIP889L PIP889L 0.000 0.900 0.000 Sec. 9.3.2.2 1 8.620 79.200 79.200 158.400
433 PIP889L PIP889L 0.000 0.900 0.000 Sec. 9.3.2.2 1 8.620 79.200 79.200 158.400
434 PIP889L PIP889L 0.056 0.900 0.062 Sec. 6.2 2 8.620 79.200 79.200 158.400
435 PIP889L PIP889L 0.061 0.900 0.068 Sec. 7.1.2 2 8.620 79.200 79.200 158.400
436 PIP889L PIP889L 0.056 0.900 0.062 Sec. 6.2 2 8.620 79.200 79.200 158.400
437 PIP889L PIP889L 0.061 0.900 0.068 Sec. 9.3.2.2 2 8.620 79.200 79.200 158.400
438 PIP889L PIP889L 0.056 0.900 0.062 Sec. 9.3.1.3 2 8.620 79.200 79.200 158.400
439 PIP889L PIP889L 0.330 0.900 0.367 Sec. 9.3.1.3 2 8.620 79.200 79.200 158.400

Print Time/Date: 07/12/2018 20:09 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 17 of 617
Job No Sheet No Rev
BN/SS/-01 18
Part
Software licensed to BN
Job Title Design of Overhead Gantry Hoarding Truss - 30m Span Ref

By Biswajit Date06-Dec-18 Chd Biswajit


Client Suntony Signage File Final Gantry Truss-30m Date/Time
Span.std 07-Dec-2018 20:06

Utilization Ratio Cont...


Beam Analysis Design Actual Allowable Ratio Clause L/C Ax Iz Iy Ix
Property Property Ratio Ratio (Act./Allow.) (cm2) (cm4) (cm4) (cm4)
440 PIP889L PIP889L 0.361 0.900 0.401 Sec. 7.1.2 2 8.620 79.200 79.200 158.400
441 PIP889L PIP889L 0.330 0.900 0.367 Sec. 9.3.1.3 2 8.620 79.200 79.200 158.400
442 PIP889L PIP889L 0.361 0.900 0.401 Sec. 7.1.2 2 8.620 79.200 79.200 158.400
443 PIP889L PIP889L 0.330 0.900 0.367 Sec. 6.2 2 8.620 79.200 79.200 158.400
444 PIP889L PIP889L 0.251 0.900 0.279 Sec. 9.3.1.3 2 8.620 79.200 79.200 158.400
445 PIP889L PIP889L 0.274 0.900 0.305 Sec. 9.3.2.2 2 8.620 79.200 79.200 158.400
446 PIP889L PIP889L 0.251 0.900 0.279 Sec. 9.3.1.3 2 8.620 79.200 79.200 158.400
447 PIP889L PIP889L 0.274 0.900 0.305 Sec. 7.1.2 2 8.620 79.200 79.200 158.400
448 PIP889L PIP889L 0.251 0.900 0.279 Sec. 6.2 2 8.620 79.200 79.200 158.400
449 PIP889L PIP889L 0.002 0.900 0.003 Sec. 6.2 2 8.620 79.200 79.200 158.400
450 PIP889L PIP889L 0.002 0.900 0.003 Sec. 7.1.2 2 8.620 79.200 79.200 158.400
451 PIP889L PIP889L 0.002 0.900 0.003 Sec. 6.2 2 8.620 79.200 79.200 158.400
452 PIP889L PIP889L 0.002 0.900 0.003 Sec. 9.3.2.2 2 8.620 79.200 79.200 158.400
453 PIP889L PIP889L 0.002 0.900 0.003 Sec. 9.3.1.3 2 8.620 79.200 79.200 158.400
454 PIP889L PIP889L 0.092 0.900 0.102 Sec. 7.1.2 3 8.620 79.200 79.200 158.400
455 PIP889L PIP889L 0.141 0.900 0.157 Sec. 9.3.1.3 2 8.620 79.200 79.200 158.400
456 PIP889L PIP889L 0.056 0.900 0.062 Sec. 9.3.1.3 2 8.620 79.200 79.200 158.400
457 PIP889L PIP889L 0.191 0.900 0.212 Sec. 7.1.2 3 8.620 79.200 79.200 158.400
458 PIP889L PIP889L 0.000 0.900 0.000 Sec. 9.3.2.2 1 8.620 79.200 79.200 158.400
459 PIP889L PIP889L 0.000 0.900 0.000 Sec. 9.3.2.2 1 8.620 79.200 79.200 158.400
460 PIP889L PIP889L 0.000 0.900 0.000 Sec. 9.3.2.2 1 8.620 79.200 79.200 158.400
461 PIP889L PIP889L 0.000 0.900 0.000 Sec. 9.3.2.2 1 8.620 79.200 79.200 158.400
462 PIP889L PIP889L 0.032 0.900 0.036 Sec. 7.1.2 2 8.620 79.200 79.200 158.400
463 PIP889L PIP889L 0.028 0.900 0.032 Sec. 6.2 3 8.620 79.200 79.200 158.400
464 PIP889L PIP889L 0.157 0.900 0.174 Sec. 6.2 2 8.620 79.200 79.200 158.400
465 PIP889L PIP889L 0.199 0.900 0.221 Sec. 7.1.2 3 8.620 79.200 79.200 158.400
466 PIP889L PIP889L 0.154 0.900 0.171 Sec. 9.3.2.2 3 8.620 79.200 79.200 158.400
467 PIP889L PIP889L 0.118 0.900 0.131 Sec. 9.3.1.3 2 8.620 79.200 79.200 158.400
468 PIP889L PIP889L 0.002 0.900 0.002 Sec. 9.3.1.3 1 8.620 79.200 79.200 158.400
469 PIP889L PIP889L 0.003 0.900 0.003 Sec. 6.2 3 8.620 79.200 79.200 158.400

Print Time/Date: 07/12/2018 20:09 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 18 of 617
Job No Sheet No Rev
BN/SS/-01 19
Part
Software licensed to BN
Job Title Design of Overhead Gantry Hoarding Truss - 30m Span Ref

By Biswajit Date06-Dec-18 Chd Biswajit


Client Suntony Signage File Final Gantry Truss-30m Date/Time
Span.std 07-Dec-2018 20:06

Base Pressure Summary


Node L/C FX FY FZ
(N/mm2) (N/mm2) (N/mm2)
Max FX 1 1:DL 0.000 0.000 0.000
Min FX 1 1:DL 0.000 0.000 0.000
Max FY 1 1:DL 0.000 0.000 0.000
Min FY 1 1:DL 0.000 0.000 0.000
Max FZ 1 1:DL 0.000 0.000 0.000
Min FZ 1 1:DL 0.000 0.000 0.000

Statics Check Results


L/C FX FY FZ MX MY MZ
(kN) (kN) (kN) (kNm) (kNm) (kNm)
1:DL Loads -0.000 -55.184 0.000 27.592 -0.000 -827.766
1:DL Reactions 0.000 55.184 -0.000 -27.592 0.000 827.766
Difference 0.000 0.000 0.000 0.000 0.000 0.000
2:WL Loads 0.000 0.000 -66.654 -533.232 999.810 0.000
2:WL Reactions -0.000 0.000 66.654 533.232 -999.810 0.000
Difference -0.000 0.000 -0.000 0.000 0.000 0.000

Print Time/Date: 07/12/2018 20:09 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 19 of 617
Job No Sheet No Rev
BN/SS/-01 20
Part
Software licensed to BN
Job Title Design of Overhead Gantry Hoarding Truss - 30m Span Ref

By Biswajit Date06-Dec-18 Chd Biswajit


Client Suntony Signage File Final Gantry Truss-30m Date/Time
Span.std 07-Dec-2018 20:06

Design Of Member No. 1 As Per IS:800

Input Parameters

Member Section PIP424L

2
Cross Sectional Area Ax (mm ) 325.00
Net section factor 1.00
2
Net Effective Sectional Area Anet (mm ) 325.00
rz (mm) 14.10
ry (mm) 14.10
Unsupported Length - Major Axis For Slenderness Check Lz (mm) 1000.00
Unsupported Length - Minor Axis For Slenderness Check Ly (mm) 1000.00
Yield Stress fy (MPa) 240.00
Allowable Ratio For Interaction Check 1.00

Design Forces

Axial Load Fx (N ) -254.85


Critical Loadcase No. 3

Details Of Calculation

Slenderness Checking

Lez (mm) 1000.00


Ley (mm) 1000.00
Lez / rz 70.93
Ley / ry 70.93
Actual Slenderness Ratio 70.93
Allowable Slenderness Ratio 400.00
Status SAFE

Check Against Axial Tension For Truss Member

Actual Tensile Stress ft (MPa)


=Fx / Anet 0.78

Print Time/Date: 07/12/2018 20:09 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 20 of 617
Job No Sheet No Rev
BN/SS/-01 21
Part
Software licensed to BN
Job Title Design of Overhead Gantry Hoarding Truss - 30m Span Ref

By Biswajit Date06-Dec-18 Chd Biswajit


Client Suntony Signage File Final Gantry Truss-30m Date/Time
Span.std 07-Dec-2018 20:06

Allowable Tensile Stress ft_allowable (MPa)


=0.60fy 144.00
Interaction ratio
=ft / ft_allowable 0.01
Status SAFE

Print Time/Date: 07/12/2018 20:09 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 21 of 617
Job No Sheet No Rev
BN/SS/-01 22
Part
Software licensed to BN
Job Title Design of Overhead Gantry Hoarding Truss - 30m Span Ref

By Biswajit Date06-Dec-18 Chd Biswajit


Client Suntony Signage File Final Gantry Truss-30m Date/Time
Span.std 07-Dec-2018 20:06

Design Of Member No. 2 As Per IS:800

Input Parameters

Member Section PIP1016L

2
Cross Sectional Area Ax (mm ) 1110.00
rz (mm) 34.62
ry (mm) 34.62
Unsupported Length - Major Axis For Slenderness Check Lz (mm) 2000.00
Unsupported Length - Minor Axis For Slenderness Check Ly (mm) 2000.00
Yield Stress fy (MPa) 240.00
Allowable Ratio For Interaction Check 1.00

Design Forces

Axial Load Fx (N ) 2648.35


Critical Loadcase No. 3

Details Of Calculation

Slenderness Checking

Lez (mm) 2000.00


Ley (mm) 2000.00
Lez / rz 57.78
Ley / ry 57.78
Actual Slenderness Ratio 57.78
Allowable Slenderness Ratio 180.00
Status SAFE

Check Against Axial Compression For Truss Member

Actual Compressive Stress fc (MPa)


=Fx / Ax 2.39

Calculation Of Allowable Compressive Stress :

Print Time/Date: 07/12/2018 20:09 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 22 of 617
Job No Sheet No Rev
BN/SS/-01 23
Part
Software licensed to BN
Job Title Design of Overhead Gantry Hoarding Truss - 30m Span Ref

By Biswajit Date06-Dec-18 Chd Biswajit


Client Suntony Signage File Final Gantry Truss-30m Date/Time
Span.std 07-Dec-2018 20:06

E (MPa) 200000.00
L/r 57.78
fcc (MPa)
2 2
=π E / λ 591.29
Allowable Compressive Stress fc_allowable (MPa)
1.4 1.4
=0.6fccfy / [(fcc) + (fy) ] 120.51
Interaction ratio
=fc / fc_allowable 0.02
Status SAFE

Print Time/Date: 07/12/2018 20:09 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 23 of 617
Job No Sheet No Rev
BN/SS/-01 24
Part
Software licensed to BN
Job Title Design of Overhead Gantry Hoarding Truss - 30m Span Ref

By Biswajit Date06-Dec-18 Chd Biswajit


Client Suntony Signage File Final Gantry Truss-30m Date/Time
Span.std 07-Dec-2018 20:06

Design Of Member No. 3 As Per IS:800

Input Parameters

Member Section PIP483L

2
Cross Sectional Area Ax (mm ) 414.00
rz (mm) 16.08
ry (mm) 16.08
Unsupported Length - Major Axis For Slenderness Check Lz (mm) 2236.06
Unsupported Length - Minor Axis For Slenderness Check Ly (mm) 2236.06
Yield Stress fy (MPa) 240.00
Allowable Ratio For Interaction Check 1.00

Design Forces

Axial Load Fx (N ) 9372.65


Critical Loadcase No. 3

Details Of Calculation

Slenderness Checking

Lez (mm) 2236.06


Ley (mm) 2236.06
Lez / rz 139.09
Ley / ry 139.09
Actual Slenderness Ratio 139.09
Allowable Slenderness Ratio 180.00
Status SAFE

Check Against Axial Compression For Truss Member

Actual Compressive Stress fc (MPa)


=Fx / Ax 22.64

Calculation Of Allowable Compressive Stress :

Print Time/Date: 07/12/2018 20:09 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 24 of 617
Job No Sheet No Rev
BN/SS/-01 25
Part
Software licensed to BN
Job Title Design of Overhead Gantry Hoarding Truss - 30m Span Ref

By Biswajit Date06-Dec-18 Chd Biswajit


Client Suntony Signage File Final Gantry Truss-30m Date/Time
Span.std 07-Dec-2018 20:06

E (MPa) 200000.00
L/r 139.09
fcc (MPa)
2 2
=π E / λ 102.03
Allowable Compressive Stress fc_allowable (MPa)
1.4 1.4
=0.6fccfy / [(fcc) + (fy) ] 50.70
Interaction ratio
=fc / fc_allowable 0.45
Status SAFE

Print Time/Date: 07/12/2018 20:09 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 25 of 617
Job No Sheet No Rev
BN/SS/-01 26
Part
Software licensed to BN
Job Title Design of Overhead Gantry Hoarding Truss - 30m Span Ref

By Biswajit Date06-Dec-18 Chd Biswajit


Client Suntony Signage File Final Gantry Truss-30m Date/Time
Span.std 07-Dec-2018 20:06

Design Of Member No. 4 As Per IS:800

Input Parameters

Member Section PIP1016L

2
Cross Sectional Area Ax (mm ) 1110.00
Net section factor 1.00
2
Net Effective Sectional Area Anet (mm ) 1110.00
rz (mm) 34.62
ry (mm) 34.62
Unsupported Length - Major Axis For Slenderness Check Lz (mm) 2000.00
Unsupported Length - Minor Axis For Slenderness Check Ly (mm) 2000.00
Yield Stress fy (MPa) 240.00
Allowable Ratio For Interaction Check 1.00

Design Forces

Axial Load Fx (N ) -22888.71


Critical Loadcase No. 3

Details Of Calculation

Slenderness Checking

Lez (mm) 2000.00


Ley (mm) 2000.00
Lez / rz 57.78
Ley / ry 57.78
Actual Slenderness Ratio 57.78
Allowable Slenderness Ratio 400.00
Status SAFE

Check Against Axial Tension For Truss Member

Actual Tensile Stress ft (MPa)


=Fx / Anet 20.62

Print Time/Date: 07/12/2018 20:09 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 26 of 617
Job No Sheet No Rev
BN/SS/-01 27
Part
Software licensed to BN
Job Title Design of Overhead Gantry Hoarding Truss - 30m Span Ref

By Biswajit Date06-Dec-18 Chd Biswajit


Client Suntony Signage File Final Gantry Truss-30m Date/Time
Span.std 07-Dec-2018 20:06

Allowable Tensile Stress ft_allowable (MPa)


=0.60fy 144.00
Interaction ratio
=ft / ft_allowable 0.14
Status SAFE

Print Time/Date: 07/12/2018 20:09 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 27 of 617
Job No Sheet No Rev
BN/SS/-01 28
Part
Software licensed to BN
Job Title Design of Overhead Gantry Hoarding Truss - 30m Span Ref

By Biswajit Date06-Dec-18 Chd Biswajit


Client Suntony Signage File Final Gantry Truss-30m Date/Time
Span.std 07-Dec-2018 20:06

Design Of Member No. 5 As Per IS:800

Input Parameters

Member Section PIP424L

2
Cross Sectional Area Ax (mm ) 325.00
Net section factor 1.00
2
Net Effective Sectional Area Anet (mm ) 325.00
rz (mm) 14.10
ry (mm) 14.10
Unsupported Length - Major Axis For Slenderness Check Lz (mm) 1000.00
Unsupported Length - Minor Axis For Slenderness Check Ly (mm) 1000.00
Yield Stress fy (MPa) 240.00
Allowable Ratio For Interaction Check 1.00

Design Forces

Axial Load Fx (N ) -2589.64


Critical Loadcase No. 3

Details Of Calculation

Slenderness Checking

Lez (mm) 1000.00


Ley (mm) 1000.00
Lez / rz 70.93
Ley / ry 70.93
Actual Slenderness Ratio 70.93
Allowable Slenderness Ratio 400.00
Status SAFE

Check Against Axial Tension For Truss Member

Actual Tensile Stress ft (MPa)


=Fx / Anet 7.97

Print Time/Date: 07/12/2018 20:09 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 28 of 617
Job No Sheet No Rev
BN/SS/-01 29
Part
Software licensed to BN
Job Title Design of Overhead Gantry Hoarding Truss - 30m Span Ref

By Biswajit Date06-Dec-18 Chd Biswajit


Client Suntony Signage File Final Gantry Truss-30m Date/Time
Span.std 07-Dec-2018 20:06

Allowable Tensile Stress ft_allowable (MPa)


=0.60fy 144.00
Interaction ratio
=ft / ft_allowable 0.06
Status SAFE

Print Time/Date: 07/12/2018 20:09 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 29 of 617
Job No Sheet No Rev
BN/SS/-01 30
Part
Software licensed to BN
Job Title Design of Overhead Gantry Hoarding Truss - 30m Span Ref

By Biswajit Date06-Dec-18 Chd Biswajit


Client Suntony Signage File Final Gantry Truss-30m Date/Time
Span.std 07-Dec-2018 20:06

Design Of Member No. 6 As Per IS:800

Input Parameters

Member Section PIP1016L

2
Cross Sectional Area Ax (mm ) 1110.00
Net section factor 1.00
2
Net Effective Sectional Area Anet (mm ) 1110.00
rz (mm) 34.62
ry (mm) 34.62
Unsupported Length - Major Axis For Slenderness Check Lz (mm) 1500.00
Unsupported Length - Minor Axis For Slenderness Check Ly (mm) 1500.00
Yield Stress fy (MPa) 240.00
Allowable Ratio For Interaction Check 1.00

Design Forces

Axial Load Fx (N ) -94655.48


Critical Loadcase No. 3

Details Of Calculation

Slenderness Checking

Lez (mm) 1500.00


Ley (mm) 1500.00
Lez / rz 43.33
Ley / ry 43.33
Actual Slenderness Ratio 43.33
Allowable Slenderness Ratio 400.00
Status SAFE

Check Against Axial Tension For Truss Member

Actual Tensile Stress ft (MPa)


=Fx / Anet 85.28

Print Time/Date: 07/12/2018 20:09 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 30 of 617
Job No Sheet No Rev
BN/SS/-01 31
Part
Software licensed to BN
Job Title Design of Overhead Gantry Hoarding Truss - 30m Span Ref

By Biswajit Date06-Dec-18 Chd Biswajit


Client Suntony Signage File Final Gantry Truss-30m Date/Time
Span.std 07-Dec-2018 20:06

Allowable Tensile Stress ft_allowable (MPa)


=0.60fy 144.00
Interaction ratio
=ft / ft_allowable 0.59
Status SAFE

Print Time/Date: 07/12/2018 20:09 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 31 of 617
Job No Sheet No Rev
BN/SS/-01 32
Part
Software licensed to BN
Job Title Design of Overhead Gantry Hoarding Truss - 30m Span Ref

By Biswajit Date06-Dec-18 Chd Biswajit


Client Suntony Signage File Final Gantry Truss-30m Date/Time
Span.std 07-Dec-2018 20:06

Design Of Member No. 7 As Per IS:800

Input Parameters

Member Section PIP603L

2
Cross Sectional Area Ax (mm ) 523.00
Net section factor 1.00
2
Net Effective Sectional Area Anet (mm ) 523.00
rz (mm) 20.32
ry (mm) 20.32
Unsupported Length - Major Axis For Slenderness Check Lz (mm) 1802.77
Unsupported Length - Minor Axis For Slenderness Check Ly (mm) 1802.77
Yield Stress fy (MPa) 240.00
Allowable Ratio For Interaction Check 1.00

Design Forces

Axial Load Fx (N ) -7070.10


Critical Loadcase No. 3

Details Of Calculation

Slenderness Checking

Lez (mm) 1802.77


Ley (mm) 1802.77
Lez / rz 88.71
Ley / ry 88.71
Actual Slenderness Ratio 88.71
Allowable Slenderness Ratio 400.00
Status SAFE

Check Against Axial Tension For Truss Member

Actual Tensile Stress ft (MPa)


=Fx / Anet 13.52

Print Time/Date: 07/12/2018 20:09 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 32 of 617
Job No Sheet No Rev
BN/SS/-01 33
Part
Software licensed to BN
Job Title Design of Overhead Gantry Hoarding Truss - 30m Span Ref

By Biswajit Date06-Dec-18 Chd Biswajit


Client Suntony Signage File Final Gantry Truss-30m Date/Time
Span.std 07-Dec-2018 20:06

Allowable Tensile Stress ft_allowable (MPa)


=0.60fy 144.00
Interaction ratio
=ft / ft_allowable 0.09
Status SAFE

Print Time/Date: 07/12/2018 20:09 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 33 of 617
Job No Sheet No Rev
BN/SS/-01 34
Part
Software licensed to BN
Job Title Design of Overhead Gantry Hoarding Truss - 30m Span Ref

By Biswajit Date06-Dec-18 Chd Biswajit


Client Suntony Signage File Final Gantry Truss-30m Date/Time
Span.std 07-Dec-2018 20:06

Design Of Member No. 8 As Per IS:800

Input Parameters

Member Section PIP1016L

2
Cross Sectional Area Ax (mm ) 1110.00
rz (mm) 34.62
ry (mm) 34.62
Unsupported Length - Major Axis For Slenderness Check Lz (mm) 1500.00
Unsupported Length - Minor Axis For Slenderness Check Ly (mm) 1500.00
Yield Stress fy (MPa) 240.00
Allowable Ratio For Interaction Check 1.00

Design Forces

Axial Load Fx (N ) 70785.36


Critical Loadcase No. 3

Details Of Calculation

Slenderness Checking

Lez (mm) 1500.00


Ley (mm) 1500.00
Lez / rz 43.33
Ley / ry 43.33
Actual Slenderness Ratio 43.33
Allowable Slenderness Ratio 180.00
Status SAFE

Check Against Axial Compression For Truss Member

Actual Compressive Stress fc (MPa)


=Fx / Ax 63.77

Calculation Of Allowable Compressive Stress :

Print Time/Date: 07/12/2018 20:09 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 34 of 617
Job No Sheet No Rev
BN/SS/-01 35
Part
Software licensed to BN
Job Title Design of Overhead Gantry Hoarding Truss - 30m Span Ref

By Biswajit Date06-Dec-18 Chd Biswajit


Client Suntony Signage File Final Gantry Truss-30m Date/Time
Span.std 07-Dec-2018 20:06

E (MPa) 200000.00
L/r 43.33
fcc (MPa)
2 2
=π E / λ 1051.18
Allowable Compressive Stress fc_allowable (MPa)
1.4 1.4
=0.6fccfy / [(fcc) + (fy) ] 132.25
Interaction ratio
=fc / fc_allowable 0.48
Status SAFE

Print Time/Date: 07/12/2018 20:09 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 35 of 617
Job No Sheet No Rev
BN/SS/-01 36
Part
Software licensed to BN
Job Title Design of Overhead Gantry Hoarding Truss - 30m Span Ref

By Biswajit Date06-Dec-18 Chd Biswajit


Client Suntony Signage File Final Gantry Truss-30m Date/Time
Span.std 07-Dec-2018 20:06

Design Of Member No. 9 As Per IS:800

Input Parameters

Member Section PIP483L

2
Cross Sectional Area Ax (mm ) 414.00
Net section factor 1.00
2
Net Effective Sectional Area Anet (mm ) 414.00
rz (mm) 16.08
ry (mm) 16.08
Unsupported Length - Major Axis For Slenderness Check Lz (mm) 2500.00
Unsupported Length - Minor Axis For Slenderness Check Ly (mm) 2500.00
Yield Stress fy (MPa) 240.00
Allowable Ratio For Interaction Check 1.00

Design Forces

Axial Load Fx (N ) -2919.97


Critical Loadcase No. 3

Details Of Calculation

Slenderness Checking

Lez (mm) 2500.00


Ley (mm) 2500.00
Lez / rz 155.51
Ley / ry 155.51
Actual Slenderness Ratio 155.51
Allowable Slenderness Ratio 400.00
Status SAFE

Check Against Axial Tension For Truss Member

Actual Tensile Stress ft (MPa)


=Fx / Anet 7.05

Print Time/Date: 07/12/2018 20:09 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 36 of 617
Job No Sheet No Rev
BN/SS/-01 37
Part
Software licensed to BN
Job Title Design of Overhead Gantry Hoarding Truss - 30m Span Ref

By Biswajit Date06-Dec-18 Chd Biswajit


Client Suntony Signage File Final Gantry Truss-30m Date/Time
Span.std 07-Dec-2018 20:06

Allowable Tensile Stress ft_allowable (MPa)


=0.60fy 144.00
Interaction ratio
=ft / ft_allowable 0.05
Status SAFE

Print Time/Date: 07/12/2018 20:09 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 37 of 617
Job No Sheet No Rev
BN/SS/-01 38
Part
Software licensed to BN
Job Title Design of Overhead Gantry Hoarding Truss - 30m Span Ref

By Biswajit Date06-Dec-18 Chd Biswajit


Client Suntony Signage File Final Gantry Truss-30m Date/Time
Span.std 07-Dec-2018 20:06

Design Of Member No. 10 As Per IS:800

Input Parameters

Member Section PIP483L

2
Cross Sectional Area Ax (mm ) 414.00
rz (mm) 16.08
ry (mm) 16.08
Unsupported Length - Major Axis For Slenderness Check Lz (mm) 2500.00
Unsupported Length - Minor Axis For Slenderness Check Ly (mm) 2500.00
Yield Stress fy (MPa) 240.00
Allowable Ratio For Interaction Check 1.00

Design Forces

Axial Load Fx (N ) 18401.85


Critical Loadcase No. 3

Details Of Calculation

Slenderness Checking

Lez (mm) 2500.00


Ley (mm) 2500.00
Lez / rz 155.51
Ley / ry 155.51
Actual Slenderness Ratio 155.51
Allowable Slenderness Ratio 180.00
Status SAFE

Check Against Axial Compression For Truss Member

Actual Compressive Stress fc (MPa)


=Fx / Ax 44.45

Calculation Of Allowable Compressive Stress :

Print Time/Date: 07/12/2018 20:09 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 38 of 617
Job No Sheet No Rev
BN/SS/-01 39
Part
Software licensed to BN
Job Title Design of Overhead Gantry Hoarding Truss - 30m Span Ref

By Biswajit Date06-Dec-18 Chd Biswajit


Client Suntony Signage File Final Gantry Truss-30m Date/Time
Span.std 07-Dec-2018 20:06

E (MPa) 200000.00
L/r 155.51
fcc (MPa)
2 2
=π E / λ 81.63
Allowable Compressive Stress fc_allowable (MPa)
1.4 1.4
=0.6fccfy / [(fcc) + (fy) ] 42.47
Interaction ratio
=fc / fc_allowable 1.05
Status UNSAFE

Print Time/Date: 07/12/2018 20:09 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 39 of 617
Job No Sheet No Rev
BN/SS/-01 40
Part
Software licensed to BN
Job Title Design of Overhead Gantry Hoarding Truss - 30m Span Ref

By Biswajit Date06-Dec-18 Chd Biswajit


Client Suntony Signage File Final Gantry Truss-30m Date/Time
Span.std 07-Dec-2018 20:06

Design Of Member No. 11 As Per IS:800

Input Parameters

Member Section PIP1016L

2
Cross Sectional Area Ax (mm ) 1110.00
Net section factor 1.00
2
Net Effective Sectional Area Anet (mm ) 1110.00
rz (mm) 34.62
ry (mm) 34.62
Unsupported Length - Major Axis For Slenderness Check Lz (mm) 1500.00
Unsupported Length - Minor Axis For Slenderness Check Ly (mm) 1500.00
Yield Stress fy (MPa) 240.00
Allowable Ratio For Interaction Check 1.00

Design Forces

Axial Load Fx (N ) -71229.27


Critical Loadcase No. 3

Details Of Calculation

Slenderness Checking

Lez (mm) 1500.00


Ley (mm) 1500.00
Lez / rz 43.33
Ley / ry 43.33
Actual Slenderness Ratio 43.33
Allowable Slenderness Ratio 400.00
Status SAFE

Check Against Axial Tension For Truss Member

Actual Tensile Stress ft (MPa)


=Fx / Anet 64.17

Print Time/Date: 07/12/2018 20:09 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 40 of 617
Job No Sheet No Rev
BN/SS/-01 41
Part
Software licensed to BN
Job Title Design of Overhead Gantry Hoarding Truss - 30m Span Ref

By Biswajit Date06-Dec-18 Chd Biswajit


Client Suntony Signage File Final Gantry Truss-30m Date/Time
Span.std 07-Dec-2018 20:06

Allowable Tensile Stress ft_allowable (MPa)


=0.60fy 144.00
Interaction ratio
=ft / ft_allowable 0.45
Status SAFE

Print Time/Date: 07/12/2018 20:09 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 41 of 617
Job No Sheet No Rev
BN/SS/-01 42
Part
Software licensed to BN
Job Title Design of Overhead Gantry Hoarding Truss - 30m Span Ref

By Biswajit Date06-Dec-18 Chd Biswajit


Client Suntony Signage File Final Gantry Truss-30m Date/Time
Span.std 07-Dec-2018 20:06

Design Of Member No. 12 As Per IS:800

Input Parameters

Member Section PIP603L

2
Cross Sectional Area Ax (mm ) 523.00
rz (mm) 20.32
ry (mm) 20.32
Unsupported Length - Major Axis For Slenderness Check Lz (mm) 1802.77
Unsupported Length - Minor Axis For Slenderness Check Ly (mm) 1802.77
Yield Stress fy (MPa) 240.00
Allowable Ratio For Interaction Check 1.00

Design Forces

Axial Load Fx (N ) 4668.54


Critical Loadcase No. 3

Details Of Calculation

Slenderness Checking

Lez (mm) 1802.77


Ley (mm) 1802.77
Lez / rz 88.71
Ley / ry 88.71
Actual Slenderness Ratio 88.71
Allowable Slenderness Ratio 180.00
Status SAFE

Check Against Axial Compression For Truss Member

Actual Compressive Stress fc (MPa)


=Fx / Ax 8.93

Calculation Of Allowable Compressive Stress :

Print Time/Date: 07/12/2018 20:09 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 42 of 617
Job No Sheet No Rev
BN/SS/-01 43
Part
Software licensed to BN
Job Title Design of Overhead Gantry Hoarding Truss - 30m Span Ref

By Biswajit Date06-Dec-18 Chd Biswajit


Client Suntony Signage File Final Gantry Truss-30m Date/Time
Span.std 07-Dec-2018 20:06

E (MPa) 200000.00
L/r 88.71
fcc (MPa)
2 2
=π E / λ 250.84
Allowable Compressive Stress fc_allowable (MPa)
1.4 1.4
=0.6fccfy / [(fcc) + (fy) ] 89.69
Interaction ratio
=fc / fc_allowable 0.10
Status SAFE

Print Time/Date: 07/12/2018 20:09 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 43 of 617
Job No Sheet No Rev
BN/SS/-01 44
Part
Software licensed to BN
Job Title Design of Overhead Gantry Hoarding Truss - 30m Span Ref

By Biswajit Date06-Dec-18 Chd Biswajit


Client Suntony Signage File Final Gantry Truss-30m Date/Time
Span.std 07-Dec-2018 20:06

Design Of Member No. 13 As Per IS:800

Input Parameters

Member Section PIP1016L

2
Cross Sectional Area Ax (mm ) 1110.00
rz (mm) 34.62
ry (mm) 34.62
Unsupported Length - Major Axis For Slenderness Check Lz (mm) 1500.00
Unsupported Length - Minor Axis For Slenderness Check Ly (mm) 1500.00
Yield Stress fy (MPa) 240.00
Allowable Ratio For Interaction Check 1.00

Design Forces

Axial Load Fx (N ) 95049.80


Critical Loadcase No. 3

Details Of Calculation

Slenderness Checking

Lez (mm) 1500.00


Ley (mm) 1500.00
Lez / rz 43.33
Ley / ry 43.33
Actual Slenderness Ratio 43.33
Allowable Slenderness Ratio 400.00
Status SAFE

Check Against Axial Compression For Truss Member

Actual Compressive Stress fc (MPa)


=Fx / Ax 85.63

Calculation Of Allowable Compressive Stress :

Print Time/Date: 07/12/2018 20:09 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 44 of 617
Job No Sheet No Rev
BN/SS/-01 45
Part
Software licensed to BN
Job Title Design of Overhead Gantry Hoarding Truss - 30m Span Ref

By Biswajit Date06-Dec-18 Chd Biswajit


Client Suntony Signage File Final Gantry Truss-30m Date/Time
Span.std 07-Dec-2018 20:06

E (MPa) 200000.00
L/r 43.33
fcc (MPa)
2 2
=π E / λ 1051.18
Allowable Compressive Stress fc_allowable (MPa)
1.4 1.4
=0.6fccfy / [(fcc) + (fy) ] 132.25
Interaction ratio
=fc / fc_allowable 0.65
Status SAFE

Print Time/Date: 07/12/2018 20:09 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 45 of 617
Job No Sheet No Rev
BN/SS/-01 46
Part
Software licensed to BN
Job Title Design of Overhead Gantry Hoarding Truss - 30m Span Ref

By Biswajit Date06-Dec-18 Chd Biswajit


Client Suntony Signage File Final Gantry Truss-30m Date/Time
Span.std 07-Dec-2018 20:06

Design Of Member No. 14 As Per IS:800

Input Parameters

Member Section PIP424L

2
Cross Sectional Area Ax (mm ) 325.00
rz (mm) 14.10
ry (mm) 14.10
Unsupported Length - Major Axis For Slenderness Check Lz (mm) 1000.00
Unsupported Length - Minor Axis For Slenderness Check Ly (mm) 1000.00
Yield Stress fy (MPa) 240.00
Allowable Ratio For Interaction Check 1.00

Design Forces

Axial Load Fx (N ) 22045.89


Critical Loadcase No. 3

Details Of Calculation

Slenderness Checking

Lez (mm) 1000.00


Ley (mm) 1000.00
Lez / rz 70.93
Ley / ry 70.93
Actual Slenderness Ratio 70.93
Allowable Slenderness Ratio 180.00
Status SAFE

Check Against Axial Compression For Truss Member

Actual Compressive Stress fc (MPa)


=Fx / Ax 67.83

Calculation Of Allowable Compressive Stress :

Print Time/Date: 07/12/2018 20:09 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 46 of 617
Job No Sheet No Rev
BN/SS/-01 47
Part
Software licensed to BN
Job Title Design of Overhead Gantry Hoarding Truss - 30m Span Ref

By Biswajit Date06-Dec-18 Chd Biswajit


Client Suntony Signage File Final Gantry Truss-30m Date/Time
Span.std 07-Dec-2018 20:06

E (MPa) 200000.00
L/r 70.93
fcc (MPa)
2 2
=π E / λ 392.36
Allowable Compressive Stress fc_allowable (MPa)
1.4 1.4
=0.6fccfy / [(fcc) + (fy) ] 107.66
Interaction ratio
=fc / fc_allowable 0.63
Status SAFE

Print Time/Date: 07/12/2018 20:09 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 47 of 617
Job No Sheet No Rev
BN/SS/-01 48
Part
Software licensed to BN
Job Title Design of Overhead Gantry Hoarding Truss - 30m Span Ref

By Biswajit Date06-Dec-18 Chd Biswajit


Client Suntony Signage File Final Gantry Truss-30m Date/Time
Span.std 07-Dec-2018 20:06

Design Of Member No. 15 As Per IS:800

Input Parameters

Member Section PIP483L

2
Cross Sectional Area Ax (mm ) 414.00
rz (mm) 16.08
ry (mm) 16.08
Unsupported Length - Major Axis For Slenderness Check Lz (mm) 2000.00
Unsupported Length - Minor Axis For Slenderness Check Ly (mm) 2000.00
Yield Stress fy (MPa) 240.00
Allowable Ratio For Interaction Check 1.00

Design Forces

Axial Load Fx (N ) 13566.65


Critical Loadcase No. 3

Details Of Calculation

Slenderness Checking

Lez (mm) 2000.00


Ley (mm) 2000.00
Lez / rz 124.40
Ley / ry 124.40
Actual Slenderness Ratio 124.40
Allowable Slenderness Ratio 180.00
Status SAFE

Check Against Axial Compression For Truss Member

Actual Compressive Stress fc (MPa)


=Fx / Ax 32.77

Calculation Of Allowable Compressive Stress :

Print Time/Date: 07/12/2018 20:09 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 48 of 617
Job No Sheet No Rev
BN/SS/-01 49
Part
Software licensed to BN
Job Title Design of Overhead Gantry Hoarding Truss - 30m Span Ref

By Biswajit Date06-Dec-18 Chd Biswajit


Client Suntony Signage File Final Gantry Truss-30m Date/Time
Span.std 07-Dec-2018 20:06

E (MPa) 200000.00
L/r 124.40
fcc (MPa)
2 2
=π E / λ 127.54
Allowable Compressive Stress fc_allowable (MPa)
1.4 1.4
=0.6fccfy / [(fcc) + (fy) ] 59.79
Interaction ratio
=fc / fc_allowable 0.55
Status SAFE

Print Time/Date: 07/12/2018 20:09 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 49 of 617
Job No Sheet No Rev
BN/SS/-01 50
Part
Software licensed to BN
Job Title Design of Overhead Gantry Hoarding Truss - 30m Span Ref

By Biswajit Date06-Dec-18 Chd Biswajit


Client Suntony Signage File Final Gantry Truss-30m Date/Time
Span.std 07-Dec-2018 20:06

Design Of Member No. 16 As Per IS:800

Input Parameters

Member Section PIP483L

2
Cross Sectional Area Ax (mm ) 414.00
Net section factor 1.00
2
Net Effective Sectional Area Anet (mm ) 414.00
rz (mm) 16.08
ry (mm) 16.08
Unsupported Length - Major Axis For Slenderness Check Lz (mm) 2000.00
Unsupported Length - Minor Axis For Slenderness Check Ly (mm) 2000.00
Yield Stress fy (MPa) 240.00
Allowable Ratio For Interaction Check 1.00

Design Forces

Axial Load Fx (N ) -25708.75


Critical Loadcase No. 3

Details Of Calculation

Slenderness Checking

Lez (mm) 2000.00


Ley (mm) 2000.00
Lez / rz 124.40
Ley / ry 124.40
Actual Slenderness Ratio 124.40
Allowable Slenderness Ratio 400.00
Status SAFE

Check Against Axial Tension For Truss Member

Actual Tensile Stress ft (MPa)


=Fx / Anet 62.10

Print Time/Date: 07/12/2018 20:09 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 50 of 617
Job No Sheet No Rev
BN/SS/-01 51
Part
Software licensed to BN
Job Title Design of Overhead Gantry Hoarding Truss - 30m Span Ref

By Biswajit Date06-Dec-18 Chd Biswajit


Client Suntony Signage File Final Gantry Truss-30m Date/Time
Span.std 07-Dec-2018 20:06

Allowable Tensile Stress ft_allowable (MPa)


=0.60fy 144.00
Interaction ratio
=ft / ft_allowable 0.43
Status SAFE

Print Time/Date: 07/12/2018 20:09 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 51 of 617
Job No Sheet No Rev
BN/SS/-01 52
Part
Software licensed to BN
Job Title Design of Overhead Gantry Hoarding Truss - 30m Span Ref

By Biswajit Date06-Dec-18 Chd Biswajit


Client Suntony Signage File Final Gantry Truss-30m Date/Time
Span.std 07-Dec-2018 20:06

Design Of Member No. 17 As Per IS:800

Input Parameters

Member Section PIP424L

2
Cross Sectional Area Ax (mm ) 0.00
rz (mm) 14.10
ry (mm) 14.10
Unsupported Length - Major Axis For Slenderness Check Lz (mm) 1000.00
Unsupported Length - Minor Axis For Slenderness Check Ly (mm) 1000.00
Yield Stress fy (MPa) 0.00
Allowable Ratio For Interaction Check 1.00

Design Forces

Axial Load Fx (N ) 0.00


Critical Loadcase No. 0

Details Of Calculation

Slenderness Checking

Lez (mm) 1000.00


Ley (mm) 1000.00
Lez / rz 70.93
Ley / ry 70.93
Actual Slenderness Ratio 70.93
Allowable Slenderness Ratio 400.00
Status SAFE

Check Against Axial Compression For Truss Member

Actual Compressive Stress fc (MPa)


=Fx / Ax 0.00

Calculation Of Allowable Compressive Stress :

Print Time/Date: 07/12/2018 20:09 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 52 of 617
Job No Sheet No Rev
BN/SS/-01 53
Part
Software licensed to BN
Job Title Design of Overhead Gantry Hoarding Truss - 30m Span Ref

By Biswajit Date06-Dec-18 Chd Biswajit


Client Suntony Signage File Final Gantry Truss-30m Date/Time
Span.std 07-Dec-2018 20:06

E (MPa) 200000.00
L/r 70.93
fcc (MPa)
2 2
=π E / λ 392.36
Allowable Compressive Stress fc_allowable (MPa)
1.4 1.4
=0.6fccfy / [(fcc) + (fy) ] 0.00
Interaction ratio
=fc / fc_allowable 0.00
Status SAFE

Print Time/Date: 07/12/2018 20:09 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 53 of 617
Job No Sheet No Rev
BN/SS/-01 54
Part
Software licensed to BN
Job Title Design of Overhead Gantry Hoarding Truss - 30m Span Ref

By Biswajit Date06-Dec-18 Chd Biswajit


Client Suntony Signage File Final Gantry Truss-30m Date/Time
Span.std 07-Dec-2018 20:06

Design Of Member No. 18 As Per IS:800

Input Parameters

Member Section PIP603L

2
Cross Sectional Area Ax (mm ) 523.00
Net section factor 1.00
2
Net Effective Sectional Area Anet (mm ) 523.00
rz (mm) 20.32
ry (mm) 20.32
Unsupported Length - Major Axis For Slenderness Check Lz (mm) 1802.77
Unsupported Length - Minor Axis For Slenderness Check Ly (mm) 1802.77
Yield Stress fy (MPa) 240.00
Allowable Ratio For Interaction Check 1.00

Design Forces

Axial Load Fx (N ) -29812.69


Critical Loadcase No. 3

Details Of Calculation

Slenderness Checking

Lez (mm) 1802.77


Ley (mm) 1802.77
Lez / rz 88.71
Ley / ry 88.71
Actual Slenderness Ratio 88.71
Allowable Slenderness Ratio 400.00
Status SAFE

Check Against Axial Tension For Truss Member

Actual Tensile Stress ft (MPa)


=Fx / Anet 57.00

Print Time/Date: 07/12/2018 20:09 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 54 of 617
Job No Sheet No Rev
BN/SS/-01 55
Part
Software licensed to BN
Job Title Design of Overhead Gantry Hoarding Truss - 30m Span Ref

By Biswajit Date06-Dec-18 Chd Biswajit


Client Suntony Signage File Final Gantry Truss-30m Date/Time
Span.std 07-Dec-2018 20:06

Allowable Tensile Stress ft_allowable (MPa)


=0.60fy 144.00
Interaction ratio
=ft / ft_allowable 0.40
Status SAFE

Print Time/Date: 07/12/2018 20:09 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 55 of 617
Job No Sheet No Rev
BN/SS/-01 56
Part
Software licensed to BN
Job Title Design of Overhead Gantry Hoarding Truss - 30m Span Ref

By Biswajit Date06-Dec-18 Chd Biswajit


Client Suntony Signage File Final Gantry Truss-30m Date/Time
Span.std 07-Dec-2018 20:06

Design Of Member No. 19 As Per IS:800

Input Parameters

Member Section PIP483L

2
Cross Sectional Area Ax (mm ) 414.00
Net section factor 1.00
2
Net Effective Sectional Area Anet (mm ) 414.00
rz (mm) 16.08
ry (mm) 16.08
Unsupported Length - Major Axis For Slenderness Check Lz (mm) 2500.00
Unsupported Length - Minor Axis For Slenderness Check Ly (mm) 2500.00
Yield Stress fy (MPa) 240.00
Allowable Ratio For Interaction Check 1.00

Design Forces

Axial Load Fx (N ) -16671.79


Critical Loadcase No. 3

Details Of Calculation

Slenderness Checking

Lez (mm) 2500.00


Ley (mm) 2500.00
Lez / rz 155.51
Ley / ry 155.51
Actual Slenderness Ratio 155.51
Allowable Slenderness Ratio 400.00
Status SAFE

Check Against Axial Tension For Truss Member

Actual Tensile Stress ft (MPa)


=Fx / Anet 40.27

Print Time/Date: 07/12/2018 20:09 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 56 of 617
Job No Sheet No Rev
BN/SS/-01 57
Part
Software licensed to BN
Job Title Design of Overhead Gantry Hoarding Truss - 30m Span Ref

By Biswajit Date06-Dec-18 Chd Biswajit


Client Suntony Signage File Final Gantry Truss-30m Date/Time
Span.std 07-Dec-2018 20:06

Allowable Tensile Stress ft_allowable (MPa)


=0.60fy 144.00
Interaction ratio
=ft / ft_allowable 0.28
Status SAFE

Print Time/Date: 07/12/2018 20:09 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 57 of 617
Job No Sheet No Rev
BN/SS/-01 58
Part
Software licensed to BN
Job Title Design of Overhead Gantry Hoarding Truss - 30m Span Ref

By Biswajit Date06-Dec-18 Chd Biswajit


Client Suntony Signage File Final Gantry Truss-30m Date/Time
Span.std 07-Dec-2018 20:06

Design Of Member No. 20 As Per IS:800

Input Parameters

Member Section PIP483L

2
Cross Sectional Area Ax (mm ) 414.00
rz (mm) 16.08
ry (mm) 16.08
Unsupported Length - Major Axis For Slenderness Check Lz (mm) 2500.00
Unsupported Length - Minor Axis For Slenderness Check Ly (mm) 2500.00
Yield Stress fy (MPa) 240.00
Allowable Ratio For Interaction Check 1.00

Design Forces

Axial Load Fx (N ) 4899.22


Critical Loadcase No. 3

Details Of Calculation

Slenderness Checking

Lez (mm) 2500.00


Ley (mm) 2500.00
Lez / rz 155.51
Ley / ry 155.51
Actual Slenderness Ratio 155.51
Allowable Slenderness Ratio 180.00
Status SAFE

Check Against Axial Compression For Truss Member

Actual Compressive Stress fc (MPa)


=Fx / Ax 11.83

Calculation Of Allowable Compressive Stress :

Print Time/Date: 07/12/2018 20:09 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 58 of 617
Job No Sheet No Rev
BN/SS/-01 59
Part
Software licensed to BN
Job Title Design of Overhead Gantry Hoarding Truss - 30m Span Ref

By Biswajit Date06-Dec-18 Chd Biswajit


Client Suntony Signage File Final Gantry Truss-30m Date/Time
Span.std 07-Dec-2018 20:06

E (MPa) 200000.00
L/r 155.51
fcc (MPa)
2 2
=π E / λ 81.63
Allowable Compressive Stress fc_allowable (MPa)
1.4 1.4
=0.6fccfy / [(fcc) + (fy) ] 42.47
Interaction ratio
=fc / fc_allowable 0.28
Status SAFE

Print Time/Date: 07/12/2018 20:09 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 59 of 617
Job No Sheet No Rev
BN/SS/-01 60
Part
Software licensed to BN
Job Title Design of Overhead Gantry Hoarding Truss - 30m Span Ref

By Biswajit Date06-Dec-18 Chd Biswajit


Client Suntony Signage File Final Gantry Truss-30m Date/Time
Span.std 07-Dec-2018 20:06

Design Of Member No. 21 As Per IS:800

Input Parameters

Member Section PIP603L

2
Cross Sectional Area Ax (mm ) 523.00
Net section factor 1.00
2
Net Effective Sectional Area Anet (mm ) 523.00
rz (mm) 20.32
ry (mm) 20.32
Unsupported Length - Major Axis For Slenderness Check Lz (mm) 1802.77
Unsupported Length - Minor Axis For Slenderness Check Ly (mm) 1802.77
Yield Stress fy (MPa) 240.00
Allowable Ratio For Interaction Check 1.00

Design Forces

Axial Load Fx (N ) -21744.99


Critical Loadcase No. 3

Details Of Calculation

Slenderness Checking

Lez (mm) 1802.77


Ley (mm) 1802.77
Lez / rz 88.71
Ley / ry 88.71
Actual Slenderness Ratio 88.71
Allowable Slenderness Ratio 400.00
Status SAFE

Check Against Axial Tension For Truss Member

Actual Tensile Stress ft (MPa)


=Fx / Anet 41.58

Print Time/Date: 07/12/2018 20:09 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 60 of 617
Job No Sheet No Rev
BN/SS/-01 61
Part
Software licensed to BN
Job Title Design of Overhead Gantry Hoarding Truss - 30m Span Ref

By Biswajit Date06-Dec-18 Chd Biswajit


Client Suntony Signage File Final Gantry Truss-30m Date/Time
Span.std 07-Dec-2018 20:06

Allowable Tensile Stress ft_allowable (MPa)


=0.60fy 144.00
Interaction ratio
=ft / ft_allowable 0.29
Status SAFE

Print Time/Date: 07/12/2018 20:09 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 61 of 617
Job No Sheet No Rev
BN/SS/-01 62
Part
Software licensed to BN
Job Title Design of Overhead Gantry Hoarding Truss - 30m Span Ref

By Biswajit Date06-Dec-18 Chd Biswajit


Client Suntony Signage File Final Gantry Truss-30m Date/Time
Span.std 07-Dec-2018 20:06

Design Of Member No. 22 As Per IS:800

Input Parameters

Member Section PIP424L

2
Cross Sectional Area Ax (mm ) 325.00
rz (mm) 14.10
ry (mm) 14.10
Unsupported Length - Major Axis For Slenderness Check Lz (mm) 1000.00
Unsupported Length - Minor Axis For Slenderness Check Ly (mm) 1000.00
Yield Stress fy (MPa) 240.00
Allowable Ratio For Interaction Check 1.00

Design Forces

Axial Load Fx (N ) 1587.00


Critical Loadcase No. 3

Details Of Calculation

Slenderness Checking

Lez (mm) 1000.00


Ley (mm) 1000.00
Lez / rz 70.93
Ley / ry 70.93
Actual Slenderness Ratio 70.93
Allowable Slenderness Ratio 180.00
Status SAFE

Check Against Axial Compression For Truss Member

Actual Compressive Stress fc (MPa)


=Fx / Ax 4.88

Calculation Of Allowable Compressive Stress :

Print Time/Date: 07/12/2018 20:09 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 62 of 617
Job No Sheet No Rev
BN/SS/-01 63
Part
Software licensed to BN
Job Title Design of Overhead Gantry Hoarding Truss - 30m Span Ref

By Biswajit Date06-Dec-18 Chd Biswajit


Client Suntony Signage File Final Gantry Truss-30m Date/Time
Span.std 07-Dec-2018 20:06

E (MPa) 200000.00
L/r 70.93
fcc (MPa)
2 2
=π E / λ 392.36
Allowable Compressive Stress fc_allowable (MPa)
1.4 1.4
=0.6fccfy / [(fcc) + (fy) ] 107.66
Interaction ratio
=fc / fc_allowable 0.05
Status SAFE

Print Time/Date: 07/12/2018 20:09 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 63 of 617
Job No Sheet No Rev
BN/SS/-01 64
Part
Software licensed to BN
Job Title Design of Overhead Gantry Hoarding Truss - 30m Span Ref

By Biswajit Date06-Dec-18 Chd Biswajit


Client Suntony Signage File Final Gantry Truss-30m Date/Time
Span.std 07-Dec-2018 20:06

Design Of Member No. 23 As Per IS:800

Input Parameters

Member Section PIP483L

2
Cross Sectional Area Ax (mm ) 414.00
rz (mm) 16.08
ry (mm) 16.08
Unsupported Length - Major Axis For Slenderness Check Lz (mm) 2000.00
Unsupported Length - Minor Axis For Slenderness Check Ly (mm) 2000.00
Yield Stress fy (MPa) 240.00
Allowable Ratio For Interaction Check 1.00

Design Forces

Axial Load Fx (N ) 9239.96


Critical Loadcase No. 3

Details Of Calculation

Slenderness Checking

Lez (mm) 2000.00


Ley (mm) 2000.00
Lez / rz 124.40
Ley / ry 124.40
Actual Slenderness Ratio 124.40
Allowable Slenderness Ratio 180.00
Status SAFE

Check Against Axial Compression For Truss Member

Actual Compressive Stress fc (MPa)


=Fx / Ax 22.32

Calculation Of Allowable Compressive Stress :

Print Time/Date: 07/12/2018 20:09 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 64 of 617
Job No Sheet No Rev
BN/SS/-01 65
Part
Software licensed to BN
Job Title Design of Overhead Gantry Hoarding Truss - 30m Span Ref

By Biswajit Date06-Dec-18 Chd Biswajit


Client Suntony Signage File Final Gantry Truss-30m Date/Time
Span.std 07-Dec-2018 20:06

E (MPa) 200000.00
L/r 124.40
fcc (MPa)
2 2
=π E / λ 127.54
Allowable Compressive Stress fc_allowable (MPa)
1.4 1.4
=0.6fccfy / [(fcc) + (fy) ] 59.79
Interaction ratio
=fc / fc_allowable 0.37
Status SAFE

Print Time/Date: 07/12/2018 20:09 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 65 of 617
Job No Sheet No Rev
BN/SS/-01 66
Part
Software licensed to BN
Job Title Design of Overhead Gantry Hoarding Truss - 30m Span Ref

By Biswajit Date06-Dec-18 Chd Biswajit


Client Suntony Signage File Final Gantry Truss-30m Date/Time
Span.std 07-Dec-2018 20:06

Design Of Member No. 24 As Per IS:800

Input Parameters

Member Section PIP483L

2
Cross Sectional Area Ax (mm ) 414.00
Net section factor 1.00
2
Net Effective Sectional Area Anet (mm ) 414.00
rz (mm) 16.08
ry (mm) 16.08
Unsupported Length - Major Axis For Slenderness Check Lz (mm) 2000.00
Unsupported Length - Minor Axis For Slenderness Check Ly (mm) 2000.00
Yield Stress fy (MPa) 240.00
Allowable Ratio For Interaction Check 1.00

Design Forces

Axial Load Fx (N ) -4148.60


Critical Loadcase No. 3

Details Of Calculation

Slenderness Checking

Lez (mm) 2000.00


Ley (mm) 2000.00
Lez / rz 124.40
Ley / ry 124.40
Actual Slenderness Ratio 124.40
Allowable Slenderness Ratio 400.00
Status SAFE

Check Against Axial Tension For Truss Member

Actual Tensile Stress ft (MPa)


=Fx / Anet 10.02

Print Time/Date: 07/12/2018 20:09 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 66 of 617
Job No Sheet No Rev
BN/SS/-01 67
Part
Software licensed to BN
Job Title Design of Overhead Gantry Hoarding Truss - 30m Span Ref

By Biswajit Date06-Dec-18 Chd Biswajit


Client Suntony Signage File Final Gantry Truss-30m Date/Time
Span.std 07-Dec-2018 20:06

Allowable Tensile Stress ft_allowable (MPa)


=0.60fy 144.00
Interaction ratio
=ft / ft_allowable 0.07
Status SAFE

Print Time/Date: 07/12/2018 20:09 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 67 of 617
Job No Sheet No Rev
BN/SS/-01 68
Part
Software licensed to BN
Job Title Design of Overhead Gantry Hoarding Truss - 30m Span Ref

By Biswajit Date06-Dec-18 Chd Biswajit


Client Suntony Signage File Final Gantry Truss-30m Date/Time
Span.std 07-Dec-2018 20:06

Design Of Member No. 25 As Per IS:800

Input Parameters

Member Section PIP424L

2
Cross Sectional Area Ax (mm ) 325.00
Net section factor 1.00
2
Net Effective Sectional Area Anet (mm ) 325.00
rz (mm) 14.10
ry (mm) 14.10
Unsupported Length - Major Axis For Slenderness Check Lz (mm) 1000.00
Unsupported Length - Minor Axis For Slenderness Check Ly (mm) 1000.00
Yield Stress fy (MPa) 240.00
Allowable Ratio For Interaction Check 1.00

Design Forces

Axial Load Fx (N ) -297.11


Critical Loadcase No. 3

Details Of Calculation

Slenderness Checking

Lez (mm) 1000.00


Ley (mm) 1000.00
Lez / rz 70.93
Ley / ry 70.93
Actual Slenderness Ratio 70.93
Allowable Slenderness Ratio 400.00
Status SAFE

Check Against Axial Tension For Truss Member

Actual Tensile Stress ft (MPa)


=Fx / Anet 0.91

Print Time/Date: 07/12/2018 20:09 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 68 of 617
Job No Sheet No Rev
BN/SS/-01 69
Part
Software licensed to BN
Job Title Design of Overhead Gantry Hoarding Truss - 30m Span Ref

By Biswajit Date06-Dec-18 Chd Biswajit


Client Suntony Signage File Final Gantry Truss-30m Date/Time
Span.std 07-Dec-2018 20:06

Allowable Tensile Stress ft_allowable (MPa)


=0.60fy 144.00
Interaction ratio
=ft / ft_allowable 0.01
Status SAFE

Print Time/Date: 07/12/2018 20:09 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 69 of 617
Job No Sheet No Rev
BN/SS/-01 70
Part
Software licensed to BN
Job Title Design of Overhead Gantry Hoarding Truss - 30m Span Ref

By Biswajit Date06-Dec-18 Chd Biswajit


Client Suntony Signage File Final Gantry Truss-30m Date/Time
Span.std 07-Dec-2018 20:06

Design Of Member No. 26 As Per IS:800

Input Parameters

Member Section PIP603L

2
Cross Sectional Area Ax (mm ) 523.00
rz (mm) 20.32
ry (mm) 20.32
Unsupported Length - Major Axis For Slenderness Check Lz (mm) 1802.77
Unsupported Length - Minor Axis For Slenderness Check Ly (mm) 1802.77
Yield Stress fy (MPa) 240.00
Allowable Ratio For Interaction Check 1.00

Design Forces

Axial Load Fx (N ) 23555.06


Critical Loadcase No. 3

Details Of Calculation

Slenderness Checking

Lez (mm) 1802.77


Ley (mm) 1802.77
Lez / rz 88.71
Ley / ry 88.71
Actual Slenderness Ratio 88.71
Allowable Slenderness Ratio 180.00
Status SAFE

Check Against Axial Compression For Truss Member

Actual Compressive Stress fc (MPa)


=Fx / Ax 45.04

Calculation Of Allowable Compressive Stress :

Print Time/Date: 07/12/2018 20:09 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 70 of 617
Job No Sheet No Rev
BN/SS/-01 71
Part
Software licensed to BN
Job Title Design of Overhead Gantry Hoarding Truss - 30m Span Ref

By Biswajit Date06-Dec-18 Chd Biswajit


Client Suntony Signage File Final Gantry Truss-30m Date/Time
Span.std 07-Dec-2018 20:06

E (MPa) 200000.00
L/r 88.71
fcc (MPa)
2 2
=π E / λ 250.84
Allowable Compressive Stress fc_allowable (MPa)
1.4 1.4
=0.6fccfy / [(fcc) + (fy) ] 89.69
Interaction ratio
=fc / fc_allowable 0.50
Status SAFE

Print Time/Date: 07/12/2018 20:09 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 71 of 617
Job No Sheet No Rev
BN/SS/-01 72
Part
Software licensed to BN
Job Title Design of Overhead Gantry Hoarding Truss - 30m Span Ref

By Biswajit Date06-Dec-18 Chd Biswajit


Client Suntony Signage File Final Gantry Truss-30m Date/Time
Span.std 07-Dec-2018 20:06

Design Of Member No. 27 As Per IS:800

Input Parameters

Member Section PIP483L

2
Cross Sectional Area Ax (mm ) 414.00
Net section factor 1.00
2
Net Effective Sectional Area Anet (mm ) 414.00
rz (mm) 16.08
ry (mm) 16.08
Unsupported Length - Major Axis For Slenderness Check Lz (mm) 2500.00
Unsupported Length - Minor Axis For Slenderness Check Ly (mm) 2500.00
Yield Stress fy (MPa) 240.00
Allowable Ratio For Interaction Check 1.00

Design Forces

Axial Load Fx (N ) -11168.36


Critical Loadcase No. 3

Details Of Calculation

Slenderness Checking

Lez (mm) 2500.00


Ley (mm) 2500.00
Lez / rz 155.51
Ley / ry 155.51
Actual Slenderness Ratio 155.51
Allowable Slenderness Ratio 400.00
Status SAFE

Check Against Axial Tension For Truss Member

Actual Tensile Stress ft (MPa)


=Fx / Anet 26.98

Print Time/Date: 07/12/2018 20:09 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 72 of 617
Job No Sheet No Rev
BN/SS/-01 73
Part
Software licensed to BN
Job Title Design of Overhead Gantry Hoarding Truss - 30m Span Ref

By Biswajit Date06-Dec-18 Chd Biswajit


Client Suntony Signage File Final Gantry Truss-30m Date/Time
Span.std 07-Dec-2018 20:06

Allowable Tensile Stress ft_allowable (MPa)


=0.60fy 144.00
Interaction ratio
=ft / ft_allowable 0.19
Status SAFE

Print Time/Date: 07/12/2018 20:09 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 73 of 617
Job No Sheet No Rev
BN/SS/-01 74
Part
Software licensed to BN
Job Title Design of Overhead Gantry Hoarding Truss - 30m Span Ref

By Biswajit Date06-Dec-18 Chd Biswajit


Client Suntony Signage File Final Gantry Truss-30m Date/Time
Span.std 07-Dec-2018 20:06

Design Of Member No. 28 As Per IS:800

Input Parameters

Member Section PIP483L

2
Cross Sectional Area Ax (mm ) 414.00
rz (mm) 16.08
ry (mm) 16.08
Unsupported Length - Major Axis For Slenderness Check Lz (mm) 2500.00
Unsupported Length - Minor Axis For Slenderness Check Ly (mm) 2500.00
Yield Stress fy (MPa) 240.00
Allowable Ratio For Interaction Check 1.00

Design Forces

Axial Load Fx (N ) 791.97


Critical Loadcase No. 3

Details Of Calculation

Slenderness Checking

Lez (mm) 2500.00


Ley (mm) 2500.00
Lez / rz 155.51
Ley / ry 155.51
Actual Slenderness Ratio 155.51
Allowable Slenderness Ratio 180.00
Status SAFE

Check Against Axial Compression For Truss Member

Actual Compressive Stress fc (MPa)


=Fx / Ax 1.91

Calculation Of Allowable Compressive Stress :

Print Time/Date: 07/12/2018 20:09 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 74 of 617
Job No Sheet No Rev
BN/SS/-01 75
Part
Software licensed to BN
Job Title Design of Overhead Gantry Hoarding Truss - 30m Span Ref

By Biswajit Date06-Dec-18 Chd Biswajit


Client Suntony Signage File Final Gantry Truss-30m Date/Time
Span.std 07-Dec-2018 20:06

E (MPa) 200000.00
L/r 155.51
fcc (MPa)
2 2
=π E / λ 81.63
Allowable Compressive Stress fc_allowable (MPa)
1.4 1.4
=0.6fccfy / [(fcc) + (fy) ] 42.47
Interaction ratio
=fc / fc_allowable 0.05
Status SAFE

Print Time/Date: 07/12/2018 20:09 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 75 of 617
Job No Sheet No Rev
BN/SS/-01 76
Part
Software licensed to BN
Job Title Design of Overhead Gantry Hoarding Truss - 30m Span Ref

By Biswajit Date06-Dec-18 Chd Biswajit


Client Suntony Signage File Final Gantry Truss-30m Date/Time
Span.std 07-Dec-2018 20:06

Design Of Member No. 29 As Per IS:800

Input Parameters

Member Section PIP603L

2
Cross Sectional Area Ax (mm ) 523.00
rz (mm) 20.32
ry (mm) 20.32
Unsupported Length - Major Axis For Slenderness Check Lz (mm) 1802.77
Unsupported Length - Minor Axis For Slenderness Check Ly (mm) 1802.77
Yield Stress fy (MPa) 240.00
Allowable Ratio For Interaction Check 1.00

Design Forces

Axial Load Fx (N ) 22280.62


Critical Loadcase No. 3

Details Of Calculation

Slenderness Checking

Lez (mm) 1802.77


Ley (mm) 1802.77
Lez / rz 88.71
Ley / ry 88.71
Actual Slenderness Ratio 88.71
Allowable Slenderness Ratio 180.00
Status SAFE

Check Against Axial Compression For Truss Member

Actual Compressive Stress fc (MPa)


=Fx / Ax 42.60

Calculation Of Allowable Compressive Stress :

Print Time/Date: 07/12/2018 20:09 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 76 of 617
Job No Sheet No Rev
BN/SS/-01 77
Part
Software licensed to BN
Job Title Design of Overhead Gantry Hoarding Truss - 30m Span Ref

By Biswajit Date06-Dec-18 Chd Biswajit


Client Suntony Signage File Final Gantry Truss-30m Date/Time
Span.std 07-Dec-2018 20:06

E (MPa) 200000.00
L/r 88.71
fcc (MPa)
2 2
=π E / λ 250.84
Allowable Compressive Stress fc_allowable (MPa)
1.4 1.4
=0.6fccfy / [(fcc) + (fy) ] 89.69
Interaction ratio
=fc / fc_allowable 0.47
Status SAFE

Print Time/Date: 07/12/2018 20:09 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 77 of 617
Job No Sheet No Rev
BN/SS/-01 78
Part
Software licensed to BN
Job Title Design of Overhead Gantry Hoarding Truss - 30m Span Ref

By Biswajit Date06-Dec-18 Chd Biswajit


Client Suntony Signage File Final Gantry Truss-30m Date/Time
Span.std 07-Dec-2018 20:06

Design Of Member No. 30 As Per IS:800

Input Parameters

Member Section PIP424L

2
Cross Sectional Area Ax (mm ) 325.00
Net section factor 1.00
2
Net Effective Sectional Area Anet (mm ) 325.00
rz (mm) 14.10
ry (mm) 14.10
Unsupported Length - Major Axis For Slenderness Check Lz (mm) 1000.00
Unsupported Length - Minor Axis For Slenderness Check Ly (mm) 1000.00
Yield Stress fy (MPa) 240.00
Allowable Ratio For Interaction Check 1.00

Design Forces

Axial Load Fx (N ) -552.91


Critical Loadcase No. 3

Details Of Calculation

Slenderness Checking

Lez (mm) 1000.00


Ley (mm) 1000.00
Lez / rz 70.93
Ley / ry 70.93
Actual Slenderness Ratio 70.93
Allowable Slenderness Ratio 400.00
Status SAFE

Check Against Axial Tension For Truss Member

Actual Tensile Stress ft (MPa)


=Fx / Anet 1.70

Print Time/Date: 07/12/2018 20:09 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 78 of 617
Job No Sheet No Rev
BN/SS/-01 79
Part
Software licensed to BN
Job Title Design of Overhead Gantry Hoarding Truss - 30m Span Ref

By Biswajit Date06-Dec-18 Chd Biswajit


Client Suntony Signage File Final Gantry Truss-30m Date/Time
Span.std 07-Dec-2018 20:06

Allowable Tensile Stress ft_allowable (MPa)


=0.60fy 144.00
Interaction ratio
=ft / ft_allowable 0.01
Status SAFE

Print Time/Date: 07/12/2018 20:09 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 79 of 617
Job No Sheet No Rev
BN/SS/-01 80
Part
Software licensed to BN
Job Title Design of Overhead Gantry Hoarding Truss - 30m Span Ref

By Biswajit Date06-Dec-18 Chd Biswajit


Client Suntony Signage File Final Gantry Truss-30m Date/Time
Span.std 07-Dec-2018 20:06

Design Of Member No. 31 As Per IS:800

Input Parameters

Member Section PIP483L

2
Cross Sectional Area Ax (mm ) 414.00
rz (mm) 16.08
ry (mm) 16.08
Unsupported Length - Major Axis For Slenderness Check Lz (mm) 2000.00
Unsupported Length - Minor Axis For Slenderness Check Ly (mm) 2000.00
Yield Stress fy (MPa) 240.00
Allowable Ratio For Interaction Check 1.00

Design Forces

Axial Load Fx (N ) 7575.66


Critical Loadcase No. 3

Details Of Calculation

Slenderness Checking

Lez (mm) 2000.00


Ley (mm) 2000.00
Lez / rz 124.40
Ley / ry 124.40
Actual Slenderness Ratio 124.40
Allowable Slenderness Ratio 180.00
Status SAFE

Check Against Axial Compression For Truss Member

Actual Compressive Stress fc (MPa)


=Fx / Ax 18.30

Calculation Of Allowable Compressive Stress :

Print Time/Date: 07/12/2018 20:09 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 80 of 617
Job No Sheet No Rev
BN/SS/-01 81
Part
Software licensed to BN
Job Title Design of Overhead Gantry Hoarding Truss - 30m Span Ref

By Biswajit Date06-Dec-18 Chd Biswajit


Client Suntony Signage File Final Gantry Truss-30m Date/Time
Span.std 07-Dec-2018 20:06

E (MPa) 200000.00
L/r 124.40
fcc (MPa)
2 2
=π E / λ 127.54
Allowable Compressive Stress fc_allowable (MPa)
1.4 1.4
=0.6fccfy / [(fcc) + (fy) ] 59.79
Interaction ratio
=fc / fc_allowable 0.31
Status SAFE

Print Time/Date: 07/12/2018 20:09 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 81 of 617
Job No Sheet No Rev
BN/SS/-01 82
Part
Software licensed to BN
Job Title Design of Overhead Gantry Hoarding Truss - 30m Span Ref

By Biswajit Date06-Dec-18 Chd Biswajit


Client Suntony Signage File Final Gantry Truss-30m Date/Time
Span.std 07-Dec-2018 20:06

Design Of Member No. 32 As Per IS:800

Input Parameters

Member Section PIP483L

2
Cross Sectional Area Ax (mm ) 414.00
Net section factor 1.00
2
Net Effective Sectional Area Anet (mm ) 414.00
rz (mm) 16.08
ry (mm) 16.08
Unsupported Length - Major Axis For Slenderness Check Lz (mm) 2000.00
Unsupported Length - Minor Axis For Slenderness Check Ly (mm) 2000.00
Yield Stress fy (MPa) 240.00
Allowable Ratio For Interaction Check 1.00

Design Forces

Axial Load Fx (N ) -938.85


Critical Loadcase No. 3

Details Of Calculation

Slenderness Checking

Lez (mm) 2000.00


Ley (mm) 2000.00
Lez / rz 124.40
Ley / ry 124.40
Actual Slenderness Ratio 124.40
Allowable Slenderness Ratio 400.00
Status SAFE

Check Against Axial Tension For Truss Member

Actual Tensile Stress ft (MPa)


=Fx / Anet 2.27

Print Time/Date: 07/12/2018 20:09 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 82 of 617
Job No Sheet No Rev
BN/SS/-01 83
Part
Software licensed to BN
Job Title Design of Overhead Gantry Hoarding Truss - 30m Span Ref

By Biswajit Date06-Dec-18 Chd Biswajit


Client Suntony Signage File Final Gantry Truss-30m Date/Time
Span.std 07-Dec-2018 20:06

Allowable Tensile Stress ft_allowable (MPa)


=0.60fy 144.00
Interaction ratio
=ft / ft_allowable 0.02
Status SAFE

Print Time/Date: 07/12/2018 20:09 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 83 of 617
Job No Sheet No Rev
BN/SS/-01 84
Part
Software licensed to BN
Job Title Design of Overhead Gantry Hoarding Truss - 30m Span Ref

By Biswajit Date06-Dec-18 Chd Biswajit


Client Suntony Signage File Final Gantry Truss-30m Date/Time
Span.std 07-Dec-2018 20:06

Design Of Member No. 33 As Per IS:800

Input Parameters

Member Section PIP424L

2
Cross Sectional Area Ax (mm ) 0.00
rz (mm) 14.10
ry (mm) 14.10
Unsupported Length - Major Axis For Slenderness Check Lz (mm) 1000.00
Unsupported Length - Minor Axis For Slenderness Check Ly (mm) 1000.00
Yield Stress fy (MPa) 0.00
Allowable Ratio For Interaction Check 1.00

Design Forces

Axial Load Fx (N ) 0.00


Critical Loadcase No. 0

Details Of Calculation

Slenderness Checking

Lez (mm) 1000.00


Ley (mm) 1000.00
Lez / rz 70.93
Ley / ry 70.93
Actual Slenderness Ratio 70.93
Allowable Slenderness Ratio 400.00
Status SAFE

Check Against Axial Compression For Truss Member

Actual Compressive Stress fc (MPa)


=Fx / Ax 0.00

Calculation Of Allowable Compressive Stress :

Print Time/Date: 07/12/2018 20:09 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 84 of 617
Job No Sheet No Rev
BN/SS/-01 85
Part
Software licensed to BN
Job Title Design of Overhead Gantry Hoarding Truss - 30m Span Ref

By Biswajit Date06-Dec-18 Chd Biswajit


Client Suntony Signage File Final Gantry Truss-30m Date/Time
Span.std 07-Dec-2018 20:06

E (MPa) 200000.00
L/r 70.93
fcc (MPa)
2 2
=π E / λ 392.36
Allowable Compressive Stress fc_allowable (MPa)
1.4 1.4
=0.6fccfy / [(fcc) + (fy) ] 0.00
Interaction ratio
=fc / fc_allowable 0.00
Status SAFE

Print Time/Date: 07/12/2018 20:09 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 85 of 617
Job No Sheet No Rev
BN/SS/-01 86
Part
Software licensed to BN
Job Title Design of Overhead Gantry Hoarding Truss - 30m Span Ref

By Biswajit Date06-Dec-18 Chd Biswajit


Client Suntony Signage File Final Gantry Truss-30m Date/Time
Span.std 07-Dec-2018 20:06

Design Of Member No. 34 As Per IS:800

Input Parameters

Member Section PIP603L

2
Cross Sectional Area Ax (mm ) 523.00
Net section factor 1.00
2
Net Effective Sectional Area Anet (mm ) 523.00
rz (mm) 20.32
ry (mm) 20.32
Unsupported Length - Major Axis For Slenderness Check Lz (mm) 1802.77
Unsupported Length - Minor Axis For Slenderness Check Ly (mm) 1802.77
Yield Stress fy (MPa) 240.00
Allowable Ratio For Interaction Check 1.00

Design Forces

Axial Load Fx (N ) -19697.28


Critical Loadcase No. 3

Details Of Calculation

Slenderness Checking

Lez (mm) 1802.77


Ley (mm) 1802.77
Lez / rz 88.71
Ley / ry 88.71
Actual Slenderness Ratio 88.71
Allowable Slenderness Ratio 400.00
Status SAFE

Check Against Axial Tension For Truss Member

Actual Tensile Stress ft (MPa)


=Fx / Anet 37.66

Print Time/Date: 07/12/2018 20:09 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 86 of 617
Job No Sheet No Rev
BN/SS/-01 87
Part
Software licensed to BN
Job Title Design of Overhead Gantry Hoarding Truss - 30m Span Ref

By Biswajit Date06-Dec-18 Chd Biswajit


Client Suntony Signage File Final Gantry Truss-30m Date/Time
Span.std 07-Dec-2018 20:06

Allowable Tensile Stress ft_allowable (MPa)


=0.60fy 144.00
Interaction ratio
=ft / ft_allowable 0.26
Status SAFE

Print Time/Date: 07/12/2018 20:09 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 87 of 617
Job No Sheet No Rev
BN/SS/-01 88
Part
Software licensed to BN
Job Title Design of Overhead Gantry Hoarding Truss - 30m Span Ref

By Biswajit Date06-Dec-18 Chd Biswajit


Client Suntony Signage File Final Gantry Truss-30m Date/Time
Span.std 07-Dec-2018 20:06

Design Of Member No. 35 As Per IS:800

Input Parameters

Member Section PIP483L

2
Cross Sectional Area Ax (mm ) 414.00
Net section factor 1.00
2
Net Effective Sectional Area Anet (mm ) 414.00
rz (mm) 16.08
ry (mm) 16.08
Unsupported Length - Major Axis For Slenderness Check Lz (mm) 2500.00
Unsupported Length - Minor Axis For Slenderness Check Ly (mm) 2500.00
Yield Stress fy (MPa) 240.00
Allowable Ratio For Interaction Check 1.00

Design Forces

Axial Load Fx (N ) -9183.05


Critical Loadcase No. 3

Details Of Calculation

Slenderness Checking

Lez (mm) 2500.00


Ley (mm) 2500.00
Lez / rz 155.51
Ley / ry 155.51
Actual Slenderness Ratio 155.51
Allowable Slenderness Ratio 400.00
Status SAFE

Check Against Axial Tension For Truss Member

Actual Tensile Stress ft (MPa)


=Fx / Anet 22.18

Print Time/Date: 07/12/2018 20:09 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 88 of 617
Job No Sheet No Rev
BN/SS/-01 89
Part
Software licensed to BN
Job Title Design of Overhead Gantry Hoarding Truss - 30m Span Ref

By Biswajit Date06-Dec-18 Chd Biswajit


Client Suntony Signage File Final Gantry Truss-30m Date/Time
Span.std 07-Dec-2018 20:06

Allowable Tensile Stress ft_allowable (MPa)


=0.60fy 144.00
Interaction ratio
=ft / ft_allowable 0.15
Status SAFE

Print Time/Date: 07/12/2018 20:09 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 89 of 617
Job No Sheet No Rev
BN/SS/-01 90
Part
Software licensed to BN
Job Title Design of Overhead Gantry Hoarding Truss - 30m Span Ref

By Biswajit Date06-Dec-18 Chd Biswajit


Client Suntony Signage File Final Gantry Truss-30m Date/Time
Span.std 07-Dec-2018 20:06

Design Of Member No. 36 As Per IS:800

Input Parameters

Member Section PIP483L

2
Cross Sectional Area Ax (mm ) 414.00
rz (mm) 16.08
ry (mm) 16.08
Unsupported Length - Major Axis For Slenderness Check Lz (mm) 2500.00
Unsupported Length - Minor Axis For Slenderness Check Ly (mm) 2500.00
Yield Stress fy (MPa) 240.00
Allowable Ratio For Interaction Check 1.00

Design Forces

Axial Load Fx (N ) 202.84


Critical Loadcase No. 3

Details Of Calculation

Slenderness Checking

Lez (mm) 2500.00


Ley (mm) 2500.00
Lez / rz 155.51
Ley / ry 155.51
Actual Slenderness Ratio 155.51
Allowable Slenderness Ratio 180.00
Status SAFE

Check Against Axial Compression For Truss Member

Actual Compressive Stress fc (MPa)


=Fx / Ax 0.49

Calculation Of Allowable Compressive Stress :

Print Time/Date: 07/12/2018 20:09 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 90 of 617
Job No Sheet No Rev
BN/SS/-01 91
Part
Software licensed to BN
Job Title Design of Overhead Gantry Hoarding Truss - 30m Span Ref

By Biswajit Date06-Dec-18 Chd Biswajit


Client Suntony Signage File Final Gantry Truss-30m Date/Time
Span.std 07-Dec-2018 20:06

E (MPa) 200000.00
L/r 155.51
fcc (MPa)
2 2
=π E / λ 81.63
Allowable Compressive Stress fc_allowable (MPa)
1.4 1.4
=0.6fccfy / [(fcc) + (fy) ] 42.47
Interaction ratio
=fc / fc_allowable 0.01
Status SAFE

Print Time/Date: 07/12/2018 20:09 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 91 of 617
Job No Sheet No Rev
BN/SS/-01 92
Part
Software licensed to BN
Job Title Design of Overhead Gantry Hoarding Truss - 30m Span Ref

By Biswajit Date06-Dec-18 Chd Biswajit


Client Suntony Signage File Final Gantry Truss-30m Date/Time
Span.std 07-Dec-2018 20:06

Design Of Member No. 37 As Per IS:800

Input Parameters

Member Section PIP603L

2
Cross Sectional Area Ax (mm ) 523.00
Net section factor 1.00
2
Net Effective Sectional Area Anet (mm ) 523.00
rz (mm) 20.32
ry (mm) 20.32
Unsupported Length - Major Axis For Slenderness Check Lz (mm) 1802.77
Unsupported Length - Minor Axis For Slenderness Check Ly (mm) 1802.77
Yield Stress fy (MPa) 240.00
Allowable Ratio For Interaction Check 1.00

Design Forces

Axial Load Fx (N ) -20416.39


Critical Loadcase No. 3

Details Of Calculation

Slenderness Checking

Lez (mm) 1802.77


Ley (mm) 1802.77
Lez / rz 88.71
Ley / ry 88.71
Actual Slenderness Ratio 88.71
Allowable Slenderness Ratio 400.00
Status SAFE

Check Against Axial Tension For Truss Member

Actual Tensile Stress ft (MPa)


=Fx / Anet 39.04

Print Time/Date: 07/12/2018 20:09 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 92 of 617
Job No Sheet No Rev
BN/SS/-01 93
Part
Software licensed to BN
Job Title Design of Overhead Gantry Hoarding Truss - 30m Span Ref

By Biswajit Date06-Dec-18 Chd Biswajit


Client Suntony Signage File Final Gantry Truss-30m Date/Time
Span.std 07-Dec-2018 20:06

Allowable Tensile Stress ft_allowable (MPa)


=0.60fy 144.00
Interaction ratio
=ft / ft_allowable 0.27
Status SAFE

Print Time/Date: 07/12/2018 20:09 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 93 of 617
Job No Sheet No Rev
BN/SS/-01 94
Part
Software licensed to BN
Job Title Design of Overhead Gantry Hoarding Truss - 30m Span Ref

By Biswajit Date06-Dec-18 Chd Biswajit


Client Suntony Signage File Final Gantry Truss-30m Date/Time
Span.std 07-Dec-2018 20:06

Design Of Member No. 38 As Per IS:800

Input Parameters

Member Section PIP424L

2
Cross Sectional Area Ax (mm ) 325.00
rz (mm) 14.10
ry (mm) 14.10
Unsupported Length - Major Axis For Slenderness Check Lz (mm) 1000.00
Unsupported Length - Minor Axis For Slenderness Check Ly (mm) 1000.00
Yield Stress fy (MPa) 240.00
Allowable Ratio For Interaction Check 1.00

Design Forces

Axial Load Fx (N ) 1587.00


Critical Loadcase No. 3

Details Of Calculation

Slenderness Checking

Lez (mm) 1000.00


Ley (mm) 1000.00
Lez / rz 70.93
Ley / ry 70.93
Actual Slenderness Ratio 70.93
Allowable Slenderness Ratio 180.00
Status SAFE

Check Against Axial Compression For Truss Member

Actual Compressive Stress fc (MPa)


=Fx / Ax 4.88

Calculation Of Allowable Compressive Stress :

Print Time/Date: 07/12/2018 20:09 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 94 of 617
Job No Sheet No Rev
BN/SS/-01 95
Part
Software licensed to BN
Job Title Design of Overhead Gantry Hoarding Truss - 30m Span Ref

By Biswajit Date06-Dec-18 Chd Biswajit


Client Suntony Signage File Final Gantry Truss-30m Date/Time
Span.std 07-Dec-2018 20:06

E (MPa) 200000.00
L/r 70.93
fcc (MPa)
2 2
=π E / λ 392.36
Allowable Compressive Stress fc_allowable (MPa)
1.4 1.4
=0.6fccfy / [(fcc) + (fy) ] 107.66
Interaction ratio
=fc / fc_allowable 0.05
Status SAFE

Print Time/Date: 07/12/2018 20:09 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 95 of 617
Job No Sheet No Rev
BN/SS/-01 96
Part
Software licensed to BN
Job Title Design of Overhead Gantry Hoarding Truss - 30m Span Ref

By Biswajit Date06-Dec-18 Chd Biswajit


Client Suntony Signage File Final Gantry Truss-30m Date/Time
Span.std 07-Dec-2018 20:06

Design Of Member No. 39 As Per IS:800

Input Parameters

Member Section PIP483L

2
Cross Sectional Area Ax (mm ) 414.00
rz (mm) 16.08
ry (mm) 16.08
Unsupported Length - Major Axis For Slenderness Check Lz (mm) 2000.00
Unsupported Length - Minor Axis For Slenderness Check Ly (mm) 2000.00
Yield Stress fy (MPa) 240.00
Allowable Ratio For Interaction Check 1.00

Design Forces

Axial Load Fx (N ) 6129.00


Critical Loadcase No. 3

Details Of Calculation

Slenderness Checking

Lez (mm) 2000.00


Ley (mm) 2000.00
Lez / rz 124.40
Ley / ry 124.40
Actual Slenderness Ratio 124.40
Allowable Slenderness Ratio 180.00
Status SAFE

Check Against Axial Compression For Truss Member

Actual Compressive Stress fc (MPa)


=Fx / Ax 14.80

Calculation Of Allowable Compressive Stress :

Print Time/Date: 07/12/2018 20:09 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 96 of 617
Job No Sheet No Rev
BN/SS/-01 97
Part
Software licensed to BN
Job Title Design of Overhead Gantry Hoarding Truss - 30m Span Ref

By Biswajit Date06-Dec-18 Chd Biswajit


Client Suntony Signage File Final Gantry Truss-30m Date/Time
Span.std 07-Dec-2018 20:06

E (MPa) 200000.00
L/r 124.40
fcc (MPa)
2 2
=π E / λ 127.54
Allowable Compressive Stress fc_allowable (MPa)
1.4 1.4
=0.6fccfy / [(fcc) + (fy) ] 59.79
Interaction ratio
=fc / fc_allowable 0.25
Status SAFE

Print Time/Date: 07/12/2018 20:09 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 97 of 617
Job No Sheet No Rev
BN/SS/-01 98
Part
Software licensed to BN
Job Title Design of Overhead Gantry Hoarding Truss - 30m Span Ref

By Biswajit Date06-Dec-18 Chd Biswajit


Client Suntony Signage File Final Gantry Truss-30m Date/Time
Span.std 07-Dec-2018 20:06

Design Of Member No. 40 As Per IS:800

Input Parameters

Member Section PIP483L

2
Cross Sectional Area Ax (mm ) 414.00
Net section factor 1.00
2
Net Effective Sectional Area Anet (mm ) 414.00
rz (mm) 16.08
ry (mm) 16.08
Unsupported Length - Major Axis For Slenderness Check Lz (mm) 2000.00
Unsupported Length - Minor Axis For Slenderness Check Ly (mm) 2000.00
Yield Stress fy (MPa) 240.00
Allowable Ratio For Interaction Check 1.00

Design Forces

Axial Load Fx (N ) -391.49


Critical Loadcase No. 3

Details Of Calculation

Slenderness Checking

Lez (mm) 2000.00


Ley (mm) 2000.00
Lez / rz 124.40
Ley / ry 124.40
Actual Slenderness Ratio 124.40
Allowable Slenderness Ratio 400.00
Status SAFE

Check Against Axial Tension For Truss Member

Actual Tensile Stress ft (MPa)


=Fx / Anet 0.95

Print Time/Date: 07/12/2018 20:09 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 98 of 617
Job No Sheet No Rev
BN/SS/-01 99
Part
Software licensed to BN
Job Title Design of Overhead Gantry Hoarding Truss - 30m Span Ref

By Biswajit Date06-Dec-18 Chd Biswajit


Client Suntony Signage File Final Gantry Truss-30m Date/Time
Span.std 07-Dec-2018 20:06

Allowable Tensile Stress ft_allowable (MPa)


=0.60fy 144.00
Interaction ratio
=ft / ft_allowable 0.01
Status SAFE

Print Time/Date: 07/12/2018 20:09 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 99 of 617
Job No Sheet No Rev
BN/SS/-01 100
Part
Software licensed to BN
Job Title Design of Overhead Gantry Hoarding Truss - 30m Span Ref

By Biswajit Date06-Dec-18 Chd Biswajit


Client Suntony Signage File Final Gantry Truss-30m Date/Time
Span.std 07-Dec-2018 20:06

Design Of Member No. 41 As Per IS:800

Input Parameters

Member Section PIP424L

2
Cross Sectional Area Ax (mm ) 325.00
rz (mm) 14.10
ry (mm) 14.10
Unsupported Length - Major Axis For Slenderness Check Lz (mm) 1000.00
Unsupported Length - Minor Axis For Slenderness Check Ly (mm) 1000.00
Yield Stress fy (MPa) 240.00
Allowable Ratio For Interaction Check 1.00

Design Forces

Axial Load Fx (N ) 1142.91


Critical Loadcase No. 3

Details Of Calculation

Slenderness Checking

Lez (mm) 1000.00


Ley (mm) 1000.00
Lez / rz 70.93
Ley / ry 70.93
Actual Slenderness Ratio 70.93
Allowable Slenderness Ratio 180.00
Status SAFE

Check Against Axial Compression For Truss Member

Actual Compressive Stress fc (MPa)


=Fx / Ax 3.52

Calculation Of Allowable Compressive Stress :

Print Time/Date: 07/12/2018 20:09 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 100 of 617
Job No Sheet No Rev
BN/SS/-01 101
Part
Software licensed to BN
Job Title Design of Overhead Gantry Hoarding Truss - 30m Span Ref

By Biswajit Date06-Dec-18 Chd Biswajit


Client Suntony Signage File Final Gantry Truss-30m Date/Time
Span.std 07-Dec-2018 20:06

E (MPa) 200000.00
L/r 70.93
fcc (MPa)
2 2
=π E / λ 392.36
Allowable Compressive Stress fc_allowable (MPa)
1.4 1.4
=0.6fccfy / [(fcc) + (fy) ] 107.66
Interaction ratio
=fc / fc_allowable 0.03
Status SAFE

Print Time/Date: 07/12/2018 20:09 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 101 of 617
Job No Sheet No Rev
BN/SS/-01 102
Part
Software licensed to BN
Job Title Design of Overhead Gantry Hoarding Truss - 30m Span Ref

By Biswajit Date06-Dec-18 Chd Biswajit


Client Suntony Signage File Final Gantry Truss-30m Date/Time
Span.std 07-Dec-2018 20:06

Design Of Member No. 42 As Per IS:800

Input Parameters

Member Section PIP603L

2
Cross Sectional Area Ax (mm ) 523.00
rz (mm) 20.32
ry (mm) 20.32
Unsupported Length - Major Axis For Slenderness Check Lz (mm) 1802.77
Unsupported Length - Minor Axis For Slenderness Check Ly (mm) 1802.77
Yield Stress fy (MPa) 240.00
Allowable Ratio For Interaction Check 1.00

Design Forces

Axial Load Fx (N ) 16035.67


Critical Loadcase No. 3

Details Of Calculation

Slenderness Checking

Lez (mm) 1802.77


Ley (mm) 1802.77
Lez / rz 88.71
Ley / ry 88.71
Actual Slenderness Ratio 88.71
Allowable Slenderness Ratio 180.00
Status SAFE

Check Against Axial Compression For Truss Member

Actual Compressive Stress fc (MPa)


=Fx / Ax 30.66

Calculation Of Allowable Compressive Stress :

Print Time/Date: 07/12/2018 20:09 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 102 of 617
Job No Sheet No Rev
BN/SS/-01 103
Part
Software licensed to BN
Job Title Design of Overhead Gantry Hoarding Truss - 30m Span Ref

By Biswajit Date06-Dec-18 Chd Biswajit


Client Suntony Signage File Final Gantry Truss-30m Date/Time
Span.std 07-Dec-2018 20:06

E (MPa) 200000.00
L/r 88.71
fcc (MPa)
2 2
=π E / λ 250.84
Allowable Compressive Stress fc_allowable (MPa)
1.4 1.4
=0.6fccfy / [(fcc) + (fy) ] 89.69
Interaction ratio
=fc / fc_allowable 0.34
Status SAFE

Print Time/Date: 07/12/2018 20:09 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 103 of 617
Job No Sheet No Rev
BN/SS/-01 104
Part
Software licensed to BN
Job Title Design of Overhead Gantry Hoarding Truss - 30m Span Ref

By Biswajit Date06-Dec-18 Chd Biswajit


Client Suntony Signage File Final Gantry Truss-30m Date/Time
Span.std 07-Dec-2018 20:06

Design Of Member No. 43 As Per IS:800

Input Parameters

Member Section PIP483L

2
Cross Sectional Area Ax (mm ) 414.00
Net section factor 1.00
2
Net Effective Sectional Area Anet (mm ) 414.00
rz (mm) 16.08
ry (mm) 16.08
Unsupported Length - Major Axis For Slenderness Check Lz (mm) 2500.00
Unsupported Length - Minor Axis For Slenderness Check Ly (mm) 2500.00
Yield Stress fy (MPa) 240.00
Allowable Ratio For Interaction Check 1.00

Design Forces

Axial Load Fx (N ) -7279.67


Critical Loadcase No. 3

Details Of Calculation

Slenderness Checking

Lez (mm) 2500.00


Ley (mm) 2500.00
Lez / rz 155.51
Ley / ry 155.51
Actual Slenderness Ratio 155.51
Allowable Slenderness Ratio 400.00
Status SAFE

Check Against Axial Tension For Truss Member

Actual Tensile Stress ft (MPa)


=Fx / Anet 17.58

Print Time/Date: 07/12/2018 20:09 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 104 of 617
Job No Sheet No Rev
BN/SS/-01 105
Part
Software licensed to BN
Job Title Design of Overhead Gantry Hoarding Truss - 30m Span Ref

By Biswajit Date06-Dec-18 Chd Biswajit


Client Suntony Signage File Final Gantry Truss-30m Date/Time
Span.std 07-Dec-2018 20:06

Allowable Tensile Stress ft_allowable (MPa)


=0.60fy 144.00
Interaction ratio
=ft / ft_allowable 0.12
Status SAFE

Print Time/Date: 07/12/2018 20:09 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 105 of 617
Job No Sheet No Rev
BN/SS/-01 106
Part
Software licensed to BN
Job Title Design of Overhead Gantry Hoarding Truss - 30m Span Ref

By Biswajit Date06-Dec-18 Chd Biswajit


Client Suntony Signage File Final Gantry Truss-30m Date/Time
Span.std 07-Dec-2018 20:06

Design Of Member No. 44 As Per IS:800

Input Parameters

Member Section PIP483L

2
Cross Sectional Area Ax (mm ) 414.00
Net section factor 1.00
2
Net Effective Sectional Area Anet (mm ) 414.00
rz (mm) 16.08
ry (mm) 16.08
Unsupported Length - Major Axis For Slenderness Check Lz (mm) 2500.00
Unsupported Length - Minor Axis For Slenderness Check Ly (mm) 2500.00
Yield Stress fy (MPa) 240.00
Allowable Ratio For Interaction Check 1.00

Design Forces

Axial Load Fx (N ) -371.16


Critical Loadcase No. 3

Details Of Calculation

Slenderness Checking

Lez (mm) 2500.00


Ley (mm) 2500.00
Lez / rz 155.51
Ley / ry 155.51
Actual Slenderness Ratio 155.51
Allowable Slenderness Ratio 400.00
Status SAFE

Check Against Axial Tension For Truss Member

Actual Tensile Stress ft (MPa)


=Fx / Anet 0.90

Print Time/Date: 07/12/2018 20:09 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 106 of 617
Job No Sheet No Rev
BN/SS/-01 107
Part
Software licensed to BN
Job Title Design of Overhead Gantry Hoarding Truss - 30m Span Ref

By Biswajit Date06-Dec-18 Chd Biswajit


Client Suntony Signage File Final Gantry Truss-30m Date/Time
Span.std 07-Dec-2018 20:06

Allowable Tensile Stress ft_allowable (MPa)


=0.60fy 144.00
Interaction ratio
=ft / ft_allowable 0.01
Status SAFE

Print Time/Date: 07/12/2018 20:09 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 107 of 617
Job No Sheet No Rev
BN/SS/-01 108
Part
Software licensed to BN
Job Title Design of Overhead Gantry Hoarding Truss - 30m Span Ref

By Biswajit Date06-Dec-18 Chd Biswajit


Client Suntony Signage File Final Gantry Truss-30m Date/Time
Span.std 07-Dec-2018 20:06

Design Of Member No. 45 As Per IS:800

Input Parameters

Member Section PIP603L

2
Cross Sectional Area Ax (mm ) 523.00
rz (mm) 20.32
ry (mm) 20.32
Unsupported Length - Major Axis For Slenderness Check Lz (mm) 1802.77
Unsupported Length - Minor Axis For Slenderness Check Ly (mm) 1802.77
Yield Stress fy (MPa) 240.00
Allowable Ratio For Interaction Check 1.00

Design Forces

Axial Load Fx (N ) 18355.99


Critical Loadcase No. 3

Details Of Calculation

Slenderness Checking

Lez (mm) 1802.77


Ley (mm) 1802.77
Lez / rz 88.71
Ley / ry 88.71
Actual Slenderness Ratio 88.71
Allowable Slenderness Ratio 180.00
Status SAFE

Check Against Axial Compression For Truss Member

Actual Compressive Stress fc (MPa)


=Fx / Ax 35.10

Calculation Of Allowable Compressive Stress :

Print Time/Date: 07/12/2018 20:09 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 108 of 617
Job No Sheet No Rev
BN/SS/-01 109
Part
Software licensed to BN
Job Title Design of Overhead Gantry Hoarding Truss - 30m Span Ref

By Biswajit Date06-Dec-18 Chd Biswajit


Client Suntony Signage File Final Gantry Truss-30m Date/Time
Span.std 07-Dec-2018 20:06

E (MPa) 200000.00
L/r 88.71
fcc (MPa)
2 2
=π E / λ 250.84
Allowable Compressive Stress fc_allowable (MPa)
1.4 1.4
=0.6fccfy / [(fcc) + (fy) ] 89.69
Interaction ratio
=fc / fc_allowable 0.39
Status SAFE

Print Time/Date: 07/12/2018 20:09 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 109 of 617
Job No Sheet No Rev
BN/SS/-01 110
Part
Software licensed to BN
Job Title Design of Overhead Gantry Hoarding Truss - 30m Span Ref

By Biswajit Date06-Dec-18 Chd Biswajit


Client Suntony Signage File Final Gantry Truss-30m Date/Time
Span.std 07-Dec-2018 20:06

Design Of Member No. 46 As Per IS:800

Input Parameters

Member Section PIP424L

2
Cross Sectional Area Ax (mm ) 325.00
rz (mm) 14.10
ry (mm) 14.10
Unsupported Length - Major Axis For Slenderness Check Lz (mm) 1000.00
Unsupported Length - Minor Axis For Slenderness Check Ly (mm) 1000.00
Yield Stress fy (MPa) 240.00
Allowable Ratio For Interaction Check 1.00

Design Forces

Axial Load Fx (N ) 103.28


Critical Loadcase No. 3

Details Of Calculation

Slenderness Checking

Lez (mm) 1000.00


Ley (mm) 1000.00
Lez / rz 70.93
Ley / ry 70.93
Actual Slenderness Ratio 70.93
Allowable Slenderness Ratio 180.00
Status SAFE

Check Against Axial Compression For Truss Member

Actual Compressive Stress fc (MPa)


=Fx / Ax 0.32

Calculation Of Allowable Compressive Stress :

Print Time/Date: 07/12/2018 20:09 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 110 of 617
Job No Sheet No Rev
BN/SS/-01 111
Part
Software licensed to BN
Job Title Design of Overhead Gantry Hoarding Truss - 30m Span Ref

By Biswajit Date06-Dec-18 Chd Biswajit


Client Suntony Signage File Final Gantry Truss-30m Date/Time
Span.std 07-Dec-2018 20:06

E (MPa) 200000.00
L/r 70.93
fcc (MPa)
2 2
=π E / λ 392.36
Allowable Compressive Stress fc_allowable (MPa)
1.4 1.4
=0.6fccfy / [(fcc) + (fy) ] 107.66
Interaction ratio
=fc / fc_allowable 0.00
Status SAFE

Print Time/Date: 07/12/2018 20:09 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 111 of 617
Job No Sheet No Rev
BN/SS/-01 112
Part
Software licensed to BN
Job Title Design of Overhead Gantry Hoarding Truss - 30m Span Ref

By Biswajit Date06-Dec-18 Chd Biswajit


Client Suntony Signage File Final Gantry Truss-30m Date/Time
Span.std 07-Dec-2018 20:06

Design Of Member No. 47 As Per IS:800

Input Parameters

Member Section PIP483L

2
Cross Sectional Area Ax (mm ) 414.00
rz (mm) 16.08
ry (mm) 16.08
Unsupported Length - Major Axis For Slenderness Check Lz (mm) 2000.00
Unsupported Length - Minor Axis For Slenderness Check Ly (mm) 2000.00
Yield Stress fy (MPa) 240.00
Allowable Ratio For Interaction Check 1.00

Design Forces

Axial Load Fx (N ) 5777.10


Critical Loadcase No. 3

Details Of Calculation

Slenderness Checking

Lez (mm) 2000.00


Ley (mm) 2000.00
Lez / rz 124.40
Ley / ry 124.40
Actual Slenderness Ratio 124.40
Allowable Slenderness Ratio 180.00
Status SAFE

Check Against Axial Compression For Truss Member

Actual Compressive Stress fc (MPa)


=Fx / Ax 13.95

Calculation Of Allowable Compressive Stress :

Print Time/Date: 07/12/2018 20:09 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 112 of 617
Job No Sheet No Rev
BN/SS/-01 113
Part
Software licensed to BN
Job Title Design of Overhead Gantry Hoarding Truss - 30m Span Ref

By Biswajit Date06-Dec-18 Chd Biswajit


Client Suntony Signage File Final Gantry Truss-30m Date/Time
Span.std 07-Dec-2018 20:06

E (MPa) 200000.00
L/r 124.40
fcc (MPa)
2 2
=π E / λ 127.54
Allowable Compressive Stress fc_allowable (MPa)
1.4 1.4
=0.6fccfy / [(fcc) + (fy) ] 59.79
Interaction ratio
=fc / fc_allowable 0.23
Status SAFE

Print Time/Date: 07/12/2018 20:09 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 113 of 617
Job No Sheet No Rev
BN/SS/-01 114
Part
Software licensed to BN
Job Title Design of Overhead Gantry Hoarding Truss - 30m Span Ref

By Biswajit Date06-Dec-18 Chd Biswajit


Client Suntony Signage File Final Gantry Truss-30m Date/Time
Span.std 07-Dec-2018 20:06

Design Of Member No. 48 As Per IS:800

Input Parameters

Member Section PIP483L

2
Cross Sectional Area Ax (mm ) 414.00
Net section factor 1.00
2
Net Effective Sectional Area Anet (mm ) 414.00
rz (mm) 16.08
ry (mm) 16.08
Unsupported Length - Major Axis For Slenderness Check Lz (mm) 2000.00
Unsupported Length - Minor Axis For Slenderness Check Ly (mm) 2000.00
Yield Stress fy (MPa) 240.00
Allowable Ratio For Interaction Check 1.00

Design Forces

Axial Load Fx (N ) -61.77


Critical Loadcase No. 3

Details Of Calculation

Slenderness Checking

Lez (mm) 2000.00


Ley (mm) 2000.00
Lez / rz 124.40
Ley / ry 124.40
Actual Slenderness Ratio 124.40
Allowable Slenderness Ratio 180.00
Status SAFE

Check Against Axial Tension For Truss Member

Actual Tensile Stress ft (MPa)


=Fx / Anet 0.15

Print Time/Date: 07/12/2018 20:09 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 114 of 617
Job No Sheet No Rev
BN/SS/-01 115
Part
Software licensed to BN
Job Title Design of Overhead Gantry Hoarding Truss - 30m Span Ref

By Biswajit Date06-Dec-18 Chd Biswajit


Client Suntony Signage File Final Gantry Truss-30m Date/Time
Span.std 07-Dec-2018 20:06

Allowable Tensile Stress ft_allowable (MPa)


=0.60fy 144.00
Interaction ratio
=ft / ft_allowable 0.00
Status SAFE

Print Time/Date: 07/12/2018 20:09 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 115 of 617
Job No Sheet No Rev
BN/SS/-01 116
Part
Software licensed to BN
Job Title Design of Overhead Gantry Hoarding Truss - 30m Span Ref

By Biswajit Date06-Dec-18 Chd Biswajit


Client Suntony Signage File Final Gantry Truss-30m Date/Time
Span.std 07-Dec-2018 20:06

Design Of Member No. 49 As Per IS:800

Input Parameters

Member Section PIP424L

2
Cross Sectional Area Ax (mm ) 0.00
rz (mm) 14.10
ry (mm) 14.10
Unsupported Length - Major Axis For Slenderness Check Lz (mm) 1000.00
Unsupported Length - Minor Axis For Slenderness Check Ly (mm) 1000.00
Yield Stress fy (MPa) 0.00
Allowable Ratio For Interaction Check 1.00

Design Forces

Axial Load Fx (N ) 0.00


Critical Loadcase No. 0

Details Of Calculation

Slenderness Checking

Lez (mm) 1000.00


Ley (mm) 1000.00
Lez / rz 70.93
Ley / ry 70.93
Actual Slenderness Ratio 70.93
Allowable Slenderness Ratio 400.00
Status SAFE

Check Against Axial Compression For Truss Member

Actual Compressive Stress fc (MPa)


=Fx / Ax 0.00

Calculation Of Allowable Compressive Stress :

Print Time/Date: 07/12/2018 20:09 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 116 of 617
Job No Sheet No Rev
BN/SS/-01 117
Part
Software licensed to BN
Job Title Design of Overhead Gantry Hoarding Truss - 30m Span Ref

By Biswajit Date06-Dec-18 Chd Biswajit


Client Suntony Signage File Final Gantry Truss-30m Date/Time
Span.std 07-Dec-2018 20:06

E (MPa) 200000.00
L/r 70.93
fcc (MPa)
2 2
=π E / λ 392.36
Allowable Compressive Stress fc_allowable (MPa)
1.4 1.4
=0.6fccfy / [(fcc) + (fy) ] 0.00
Interaction ratio
=fc / fc_allowable 0.00
Status SAFE

Print Time/Date: 07/12/2018 20:09 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 117 of 617
Job No Sheet No Rev
BN/SS/-01 118
Part
Software licensed to BN
Job Title Design of Overhead Gantry Hoarding Truss - 30m Span Ref

By Biswajit Date06-Dec-18 Chd Biswajit


Client Suntony Signage File Final Gantry Truss-30m Date/Time
Span.std 07-Dec-2018 20:06

Design Of Member No. 50 As Per IS:800

Input Parameters

Member Section PIP603L

2
Cross Sectional Area Ax (mm ) 523.00
Net section factor 1.00
2
Net Effective Sectional Area Anet (mm ) 523.00
rz (mm) 20.32
ry (mm) 20.32
Unsupported Length - Major Axis For Slenderness Check Lz (mm) 1802.77
Unsupported Length - Minor Axis For Slenderness Check Ly (mm) 1802.77
Yield Stress fy (MPa) 240.00
Allowable Ratio For Interaction Check 1.00

Design Forces

Axial Load Fx (N ) -13360.86


Critical Loadcase No. 3

Details Of Calculation

Slenderness Checking

Lez (mm) 1802.77


Ley (mm) 1802.77
Lez / rz 88.71
Ley / ry 88.71
Actual Slenderness Ratio 88.71
Allowable Slenderness Ratio 400.00
Status SAFE

Check Against Axial Tension For Truss Member

Actual Tensile Stress ft (MPa)


=Fx / Anet 25.55

Print Time/Date: 07/12/2018 20:09 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 118 of 617
Job No Sheet No Rev
BN/SS/-01 119
Part
Software licensed to BN
Job Title Design of Overhead Gantry Hoarding Truss - 30m Span Ref

By Biswajit Date06-Dec-18 Chd Biswajit


Client Suntony Signage File Final Gantry Truss-30m Date/Time
Span.std 07-Dec-2018 20:06

Allowable Tensile Stress ft_allowable (MPa)


=0.60fy 144.00
Interaction ratio
=ft / ft_allowable 0.18
Status SAFE

Print Time/Date: 07/12/2018 20:09 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 119 of 617
Job No Sheet No Rev
BN/SS/-01 120
Part
Software licensed to BN
Job Title Design of Overhead Gantry Hoarding Truss - 30m Span Ref

By Biswajit Date06-Dec-18 Chd Biswajit


Client Suntony Signage File Final Gantry Truss-30m Date/Time
Span.std 07-Dec-2018 20:06

Design Of Member No. 51 As Per IS:800

Input Parameters

Member Section PIP483L

2
Cross Sectional Area Ax (mm ) 414.00
Net section factor 1.00
2
Net Effective Sectional Area Anet (mm ) 414.00
rz (mm) 16.08
ry (mm) 16.08
Unsupported Length - Major Axis For Slenderness Check Lz (mm) 2500.00
Unsupported Length - Minor Axis For Slenderness Check Ly (mm) 2500.00
Yield Stress fy (MPa) 240.00
Allowable Ratio For Interaction Check 1.00

Design Forces

Axial Load Fx (N ) -6934.85


Critical Loadcase No. 3

Details Of Calculation

Slenderness Checking

Lez (mm) 2500.00


Ley (mm) 2500.00
Lez / rz 155.51
Ley / ry 155.51
Actual Slenderness Ratio 155.51
Allowable Slenderness Ratio 400.00
Status SAFE

Check Against Axial Tension For Truss Member

Actual Tensile Stress ft (MPa)


=Fx / Anet 16.75

Print Time/Date: 07/12/2018 20:09 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 120 of 617
Job No Sheet No Rev
BN/SS/-01 121
Part
Software licensed to BN
Job Title Design of Overhead Gantry Hoarding Truss - 30m Span Ref

By Biswajit Date06-Dec-18 Chd Biswajit


Client Suntony Signage File Final Gantry Truss-30m Date/Time
Span.std 07-Dec-2018 20:06

Allowable Tensile Stress ft_allowable (MPa)


=0.60fy 144.00
Interaction ratio
=ft / ft_allowable 0.12
Status SAFE

Print Time/Date: 07/12/2018 20:09 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 121 of 617
Job No Sheet No Rev
BN/SS/-01 122
Part
Software licensed to BN
Job Title Design of Overhead Gantry Hoarding Truss - 30m Span Ref

By Biswajit Date06-Dec-18 Chd Biswajit


Client Suntony Signage File Final Gantry Truss-30m Date/Time
Span.std 07-Dec-2018 20:06

Design Of Member No. 52 As Per IS:800

Input Parameters

Member Section PIP483L

2
Cross Sectional Area Ax (mm ) 414.00
rz (mm) 16.08
ry (mm) 16.08
Unsupported Length - Major Axis For Slenderness Check Lz (mm) 2500.00
Unsupported Length - Minor Axis For Slenderness Check Ly (mm) 2500.00
Yield Stress fy (MPa) 240.00
Allowable Ratio For Interaction Check 1.00

Design Forces

Axial Load Fx (N ) 746.99


Critical Loadcase No. 3

Details Of Calculation

Slenderness Checking

Lez (mm) 2500.00


Ley (mm) 2500.00
Lez / rz 155.51
Ley / ry 155.51
Actual Slenderness Ratio 155.51
Allowable Slenderness Ratio 180.00
Status SAFE

Check Against Axial Compression For Truss Member

Actual Compressive Stress fc (MPa)


=Fx / Ax 1.80

Calculation Of Allowable Compressive Stress :

Print Time/Date: 07/12/2018 20:09 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 122 of 617
Job No Sheet No Rev
BN/SS/-01 123
Part
Software licensed to BN
Job Title Design of Overhead Gantry Hoarding Truss - 30m Span Ref

By Biswajit Date06-Dec-18 Chd Biswajit


Client Suntony Signage File Final Gantry Truss-30m Date/Time
Span.std 07-Dec-2018 20:06

E (MPa) 200000.00
L/r 155.51
fcc (MPa)
2 2
=π E / λ 81.63
Allowable Compressive Stress fc_allowable (MPa)
1.4 1.4
=0.6fccfy / [(fcc) + (fy) ] 42.47
Interaction ratio
=fc / fc_allowable 0.04
Status SAFE

Print Time/Date: 07/12/2018 20:09 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 123 of 617
Job No Sheet No Rev
BN/SS/-01 124
Part
Software licensed to BN
Job Title Design of Overhead Gantry Hoarding Truss - 30m Span Ref

By Biswajit Date06-Dec-18 Chd Biswajit


Client Suntony Signage File Final Gantry Truss-30m Date/Time
Span.std 07-Dec-2018 20:06

Design Of Member No. 53 As Per IS:800

Input Parameters

Member Section PIP603L

2
Cross Sectional Area Ax (mm ) 523.00
Net section factor 1.00
2
Net Effective Sectional Area Anet (mm ) 523.00
rz (mm) 20.32
ry (mm) 20.32
Unsupported Length - Major Axis For Slenderness Check Lz (mm) 1802.77
Unsupported Length - Minor Axis For Slenderness Check Ly (mm) 1802.77
Yield Stress fy (MPa) 240.00
Allowable Ratio For Interaction Check 1.00

Design Forces

Axial Load Fx (N ) -15308.79


Critical Loadcase No. 3

Details Of Calculation

Slenderness Checking

Lez (mm) 1802.77


Ley (mm) 1802.77
Lez / rz 88.71
Ley / ry 88.71
Actual Slenderness Ratio 88.71
Allowable Slenderness Ratio 400.00
Status SAFE

Check Against Axial Tension For Truss Member

Actual Tensile Stress ft (MPa)


=Fx / Anet 29.27

Print Time/Date: 07/12/2018 20:09 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 124 of 617
Job No Sheet No Rev
BN/SS/-01 125
Part
Software licensed to BN
Job Title Design of Overhead Gantry Hoarding Truss - 30m Span Ref

By Biswajit Date06-Dec-18 Chd Biswajit


Client Suntony Signage File Final Gantry Truss-30m Date/Time
Span.std 07-Dec-2018 20:06

Allowable Tensile Stress ft_allowable (MPa)


=0.60fy 144.00
Interaction ratio
=ft / ft_allowable 0.20
Status SAFE

Print Time/Date: 07/12/2018 20:09 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 125 of 617
Job No Sheet No Rev
BN/SS/-01 126
Part
Software licensed to BN
Job Title Design of Overhead Gantry Hoarding Truss - 30m Span Ref

By Biswajit Date06-Dec-18 Chd Biswajit


Client Suntony Signage File Final Gantry Truss-30m Date/Time
Span.std 07-Dec-2018 20:06

Design Of Member No. 54 As Per IS:800

Input Parameters

Member Section PIP424L

2
Cross Sectional Area Ax (mm ) 325.00
rz (mm) 14.10
ry (mm) 14.10
Unsupported Length - Major Axis For Slenderness Check Lz (mm) 1000.00
Unsupported Length - Minor Axis For Slenderness Check Ly (mm) 1000.00
Yield Stress fy (MPa) 240.00
Allowable Ratio For Interaction Check 1.00

Design Forces

Axial Load Fx (N ) 1587.00


Critical Loadcase No. 3

Details Of Calculation

Slenderness Checking

Lez (mm) 1000.00


Ley (mm) 1000.00
Lez / rz 70.93
Ley / ry 70.93
Actual Slenderness Ratio 70.93
Allowable Slenderness Ratio 180.00
Status SAFE

Check Against Axial Compression For Truss Member

Actual Compressive Stress fc (MPa)


=Fx / Ax 4.88

Calculation Of Allowable Compressive Stress :

Print Time/Date: 07/12/2018 20:09 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 126 of 617
Job No Sheet No Rev
BN/SS/-01 127
Part
Software licensed to BN
Job Title Design of Overhead Gantry Hoarding Truss - 30m Span Ref

By Biswajit Date06-Dec-18 Chd Biswajit


Client Suntony Signage File Final Gantry Truss-30m Date/Time
Span.std 07-Dec-2018 20:06

E (MPa) 200000.00
L/r 70.93
fcc (MPa)
2 2
=π E / λ 392.36
Allowable Compressive Stress fc_allowable (MPa)
1.4 1.4
=0.6fccfy / [(fcc) + (fy) ] 107.66
Interaction ratio
=fc / fc_allowable 0.05
Status SAFE

Print Time/Date: 07/12/2018 20:09 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 127 of 617
Job No Sheet No Rev
BN/SS/-01 128
Part
Software licensed to BN
Job Title Design of Overhead Gantry Hoarding Truss - 30m Span Ref

By Biswajit Date06-Dec-18 Chd Biswajit


Client Suntony Signage File Final Gantry Truss-30m Date/Time
Span.std 07-Dec-2018 20:06

Design Of Member No. 55 As Per IS:800

Input Parameters

Member Section PIP483L

2
Cross Sectional Area Ax (mm ) 414.00
rz (mm) 16.08
ry (mm) 16.08
Unsupported Length - Major Axis For Slenderness Check Lz (mm) 2000.00
Unsupported Length - Minor Axis For Slenderness Check Ly (mm) 2000.00
Yield Stress fy (MPa) 240.00
Allowable Ratio For Interaction Check 1.00

Design Forces

Axial Load Fx (N ) 4485.70


Critical Loadcase No. 3

Details Of Calculation

Slenderness Checking

Lez (mm) 2000.00


Ley (mm) 2000.00
Lez / rz 124.40
Ley / ry 124.40
Actual Slenderness Ratio 124.40
Allowable Slenderness Ratio 180.00
Status SAFE

Check Against Axial Compression For Truss Member

Actual Compressive Stress fc (MPa)


=Fx / Ax 10.84

Calculation Of Allowable Compressive Stress :

Print Time/Date: 07/12/2018 20:09 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 128 of 617
Job No Sheet No Rev
BN/SS/-01 129
Part
Software licensed to BN
Job Title Design of Overhead Gantry Hoarding Truss - 30m Span Ref

By Biswajit Date06-Dec-18 Chd Biswajit


Client Suntony Signage File Final Gantry Truss-30m Date/Time
Span.std 07-Dec-2018 20:06

E (MPa) 200000.00
L/r 124.40
fcc (MPa)
2 2
=π E / λ 127.54
Allowable Compressive Stress fc_allowable (MPa)
1.4 1.4
=0.6fccfy / [(fcc) + (fy) ] 59.79
Interaction ratio
=fc / fc_allowable 0.18
Status SAFE

Print Time/Date: 07/12/2018 20:09 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 129 of 617
Job No Sheet No Rev
BN/SS/-01 130
Part
Software licensed to BN
Job Title Design of Overhead Gantry Hoarding Truss - 30m Span Ref

By Biswajit Date06-Dec-18 Chd Biswajit


Client Suntony Signage File Final Gantry Truss-30m Date/Time
Span.std 07-Dec-2018 20:06

Design Of Member No. 56 As Per IS:800

Input Parameters

Member Section PIP483L

2
Cross Sectional Area Ax (mm ) 414.00
Net section factor 1.00
2
Net Effective Sectional Area Anet (mm ) 414.00
rz (mm) 16.08
ry (mm) 16.08
Unsupported Length - Major Axis For Slenderness Check Lz (mm) 2000.00
Unsupported Length - Minor Axis For Slenderness Check Ly (mm) 2000.00
Yield Stress fy (MPa) 240.00
Allowable Ratio For Interaction Check 1.00

Design Forces

Axial Load Fx (N ) -826.81


Critical Loadcase No. 3

Details Of Calculation

Slenderness Checking

Lez (mm) 2000.00


Ley (mm) 2000.00
Lez / rz 124.40
Ley / ry 124.40
Actual Slenderness Ratio 124.40
Allowable Slenderness Ratio 400.00
Status SAFE

Check Against Axial Tension For Truss Member

Actual Tensile Stress ft (MPa)


=Fx / Anet 2.00

Print Time/Date: 07/12/2018 20:09 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 130 of 617
Job No Sheet No Rev
BN/SS/-01 131
Part
Software licensed to BN
Job Title Design of Overhead Gantry Hoarding Truss - 30m Span Ref

By Biswajit Date06-Dec-18 Chd Biswajit


Client Suntony Signage File Final Gantry Truss-30m Date/Time
Span.std 07-Dec-2018 20:06

Allowable Tensile Stress ft_allowable (MPa)


=0.60fy 144.00
Interaction ratio
=ft / ft_allowable 0.01
Status SAFE

Print Time/Date: 07/12/2018 20:09 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 131 of 617
Job No Sheet No Rev
BN/SS/-01 132
Part
Software licensed to BN
Job Title Design of Overhead Gantry Hoarding Truss - 30m Span Ref

By Biswajit Date06-Dec-18 Chd Biswajit


Client Suntony Signage File Final Gantry Truss-30m Date/Time
Span.std 07-Dec-2018 20:06

Design Of Member No. 57 As Per IS:800

Input Parameters

Member Section PIP424L

2
Cross Sectional Area Ax (mm ) 325.00
rz (mm) 14.10
ry (mm) 14.10
Unsupported Length - Major Axis For Slenderness Check Lz (mm) 1000.00
Unsupported Length - Minor Axis For Slenderness Check Ly (mm) 1000.00
Yield Stress fy (MPa) 240.00
Allowable Ratio For Interaction Check 1.00

Design Forces

Axial Load Fx (N ) 1220.53


Critical Loadcase No. 3

Details Of Calculation

Slenderness Checking

Lez (mm) 1000.00


Ley (mm) 1000.00
Lez / rz 70.93
Ley / ry 70.93
Actual Slenderness Ratio 70.93
Allowable Slenderness Ratio 180.00
Status SAFE

Check Against Axial Compression For Truss Member

Actual Compressive Stress fc (MPa)


=Fx / Ax 3.76

Calculation Of Allowable Compressive Stress :

Print Time/Date: 07/12/2018 20:09 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 132 of 617
Job No Sheet No Rev
BN/SS/-01 133
Part
Software licensed to BN
Job Title Design of Overhead Gantry Hoarding Truss - 30m Span Ref

By Biswajit Date06-Dec-18 Chd Biswajit


Client Suntony Signage File Final Gantry Truss-30m Date/Time
Span.std 07-Dec-2018 20:06

E (MPa) 200000.00
L/r 70.93
fcc (MPa)
2 2
=π E / λ 392.36
Allowable Compressive Stress fc_allowable (MPa)
1.4 1.4
=0.6fccfy / [(fcc) + (fy) ] 107.66
Interaction ratio
=fc / fc_allowable 0.03
Status SAFE

Print Time/Date: 07/12/2018 20:09 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 133 of 617
Job No Sheet No Rev
BN/SS/-01 134
Part
Software licensed to BN
Job Title Design of Overhead Gantry Hoarding Truss - 30m Span Ref

By Biswajit Date06-Dec-18 Chd Biswajit


Client Suntony Signage File Final Gantry Truss-30m Date/Time
Span.std 07-Dec-2018 20:06

Design Of Member No. 58 As Per IS:800

Input Parameters

Member Section PIP603L

2
Cross Sectional Area Ax (mm ) 523.00
rz (mm) 20.32
ry (mm) 20.32
Unsupported Length - Major Axis For Slenderness Check Lz (mm) 1802.77
Unsupported Length - Minor Axis For Slenderness Check Ly (mm) 1802.77
Yield Stress fy (MPa) 240.00
Allowable Ratio For Interaction Check 1.00

Design Forces

Axial Load Fx (N ) 9839.20


Critical Loadcase No. 3

Details Of Calculation

Slenderness Checking

Lez (mm) 1802.77


Ley (mm) 1802.77
Lez / rz 88.71
Ley / ry 88.71
Actual Slenderness Ratio 88.71
Allowable Slenderness Ratio 180.00
Status SAFE

Check Against Axial Compression For Truss Member

Actual Compressive Stress fc (MPa)


=Fx / Ax 18.81

Calculation Of Allowable Compressive Stress :

Print Time/Date: 07/12/2018 20:09 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 134 of 617
Job No Sheet No Rev
BN/SS/-01 135
Part
Software licensed to BN
Job Title Design of Overhead Gantry Hoarding Truss - 30m Span Ref

By Biswajit Date06-Dec-18 Chd Biswajit


Client Suntony Signage File Final Gantry Truss-30m Date/Time
Span.std 07-Dec-2018 20:06

E (MPa) 200000.00
L/r 88.71
fcc (MPa)
2 2
=π E / λ 250.84
Allowable Compressive Stress fc_allowable (MPa)
1.4 1.4
=0.6fccfy / [(fcc) + (fy) ] 89.69
Interaction ratio
=fc / fc_allowable 0.21
Status SAFE

Print Time/Date: 07/12/2018 20:09 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 135 of 617
Job No Sheet No Rev
BN/SS/-01 136
Part
Software licensed to BN
Job Title Design of Overhead Gantry Hoarding Truss - 30m Span Ref

By Biswajit Date06-Dec-18 Chd Biswajit


Client Suntony Signage File Final Gantry Truss-30m Date/Time
Span.std 07-Dec-2018 20:06

Design Of Member No. 59 As Per IS:800

Input Parameters

Member Section PIP483L

2
Cross Sectional Area Ax (mm ) 414.00
Net section factor 1.00
2
Net Effective Sectional Area Anet (mm ) 414.00
rz (mm) 16.08
ry (mm) 16.08
Unsupported Length - Major Axis For Slenderness Check Lz (mm) 2500.00
Unsupported Length - Minor Axis For Slenderness Check Ly (mm) 2500.00
Yield Stress fy (MPa) 240.00
Allowable Ratio For Interaction Check 1.00

Design Forces

Axial Load Fx (N ) -5225.53


Critical Loadcase No. 3

Details Of Calculation

Slenderness Checking

Lez (mm) 2500.00


Ley (mm) 2500.00
Lez / rz 155.51
Ley / ry 155.51
Actual Slenderness Ratio 155.51
Allowable Slenderness Ratio 400.00
Status SAFE

Check Against Axial Tension For Truss Member

Actual Tensile Stress ft (MPa)


=Fx / Anet 12.62

Print Time/Date: 07/12/2018 20:09 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 136 of 617
Job No Sheet No Rev
BN/SS/-01 137
Part
Software licensed to BN
Job Title Design of Overhead Gantry Hoarding Truss - 30m Span Ref

By Biswajit Date06-Dec-18 Chd Biswajit


Client Suntony Signage File Final Gantry Truss-30m Date/Time
Span.std 07-Dec-2018 20:06

Allowable Tensile Stress ft_allowable (MPa)


=0.60fy 144.00
Interaction ratio
=ft / ft_allowable 0.09
Status SAFE

Print Time/Date: 07/12/2018 20:09 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 137 of 617
Job No Sheet No Rev
BN/SS/-01 138
Part
Software licensed to BN
Job Title Design of Overhead Gantry Hoarding Truss - 30m Span Ref

By Biswajit Date06-Dec-18 Chd Biswajit


Client Suntony Signage File Final Gantry Truss-30m Date/Time
Span.std 07-Dec-2018 20:06

Design Of Member No. 60 As Per IS:800

Input Parameters

Member Section PIP483L

2
Cross Sectional Area Ax (mm ) 414.00
rz (mm) 16.08
ry (mm) 16.08
Unsupported Length - Major Axis For Slenderness Check Lz (mm) 2500.00
Unsupported Length - Minor Axis For Slenderness Check Ly (mm) 2500.00
Yield Stress fy (MPa) 240.00
Allowable Ratio For Interaction Check 1.00

Design Forces

Axial Load Fx (N ) 433.85


Critical Loadcase No. 3

Details Of Calculation

Slenderness Checking

Lez (mm) 2500.00


Ley (mm) 2500.00
Lez / rz 155.51
Ley / ry 155.51
Actual Slenderness Ratio 155.51
Allowable Slenderness Ratio 180.00
Status SAFE

Check Against Axial Compression For Truss Member

Actual Compressive Stress fc (MPa)


=Fx / Ax 1.05

Calculation Of Allowable Compressive Stress :

Print Time/Date: 07/12/2018 20:09 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 138 of 617
Job No Sheet No Rev
BN/SS/-01 139
Part
Software licensed to BN
Job Title Design of Overhead Gantry Hoarding Truss - 30m Span Ref

By Biswajit Date06-Dec-18 Chd Biswajit


Client Suntony Signage File Final Gantry Truss-30m Date/Time
Span.std 07-Dec-2018 20:06

E (MPa) 200000.00
L/r 155.51
fcc (MPa)
2 2
=π E / λ 81.63
Allowable Compressive Stress fc_allowable (MPa)
1.4 1.4
=0.6fccfy / [(fcc) + (fy) ] 42.47
Interaction ratio
=fc / fc_allowable 0.02
Status SAFE

Print Time/Date: 07/12/2018 20:09 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 139 of 617
Job No Sheet No Rev
BN/SS/-01 140
Part
Software licensed to BN
Job Title Design of Overhead Gantry Hoarding Truss - 30m Span Ref

By Biswajit Date06-Dec-18 Chd Biswajit


Client Suntony Signage File Final Gantry Truss-30m Date/Time
Span.std 07-Dec-2018 20:06

Design Of Member No. 61 As Per IS:800

Input Parameters

Member Section PIP603L

2
Cross Sectional Area Ax (mm ) 523.00
rz (mm) 20.32
ry (mm) 20.32
Unsupported Length - Major Axis For Slenderness Check Lz (mm) 1802.77
Unsupported Length - Minor Axis For Slenderness Check Ly (mm) 1802.77
Yield Stress fy (MPa) 240.00
Allowable Ratio For Interaction Check 1.00

Design Forces

Axial Load Fx (N ) 13108.44


Critical Loadcase No. 3

Details Of Calculation

Slenderness Checking

Lez (mm) 1802.77


Ley (mm) 1802.77
Lez / rz 88.71
Ley / ry 88.71
Actual Slenderness Ratio 88.71
Allowable Slenderness Ratio 180.00
Status SAFE

Check Against Axial Compression For Truss Member

Actual Compressive Stress fc (MPa)


=Fx / Ax 25.06

Calculation Of Allowable Compressive Stress :

Print Time/Date: 07/12/2018 20:09 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 140 of 617
Job No Sheet No Rev
BN/SS/-01 141
Part
Software licensed to BN
Job Title Design of Overhead Gantry Hoarding Truss - 30m Span Ref

By Biswajit Date06-Dec-18 Chd Biswajit


Client Suntony Signage File Final Gantry Truss-30m Date/Time
Span.std 07-Dec-2018 20:06

E (MPa) 200000.00
L/r 88.71
fcc (MPa)
2 2
=π E / λ 250.84
Allowable Compressive Stress fc_allowable (MPa)
1.4 1.4
=0.6fccfy / [(fcc) + (fy) ] 89.69
Interaction ratio
=fc / fc_allowable 0.28
Status SAFE

Print Time/Date: 07/12/2018 20:09 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 141 of 617
Job No Sheet No Rev
BN/SS/-01 142
Part
Software licensed to BN
Job Title Design of Overhead Gantry Hoarding Truss - 30m Span Ref

By Biswajit Date06-Dec-18 Chd Biswajit


Client Suntony Signage File Final Gantry Truss-30m Date/Time
Span.std 07-Dec-2018 20:06

Design Of Member No. 62 As Per IS:800

Input Parameters

Member Section PIP424L

2
Cross Sectional Area Ax (mm ) 325.00
rz (mm) 14.10
ry (mm) 14.10
Unsupported Length - Major Axis For Slenderness Check Lz (mm) 1000.00
Unsupported Length - Minor Axis For Slenderness Check Ly (mm) 1000.00
Yield Stress fy (MPa) 240.00
Allowable Ratio For Interaction Check 1.00

Design Forces

Axial Load Fx (N ) 302.65


Critical Loadcase No. 3

Details Of Calculation

Slenderness Checking

Lez (mm) 1000.00


Ley (mm) 1000.00
Lez / rz 70.93
Ley / ry 70.93
Actual Slenderness Ratio 70.93
Allowable Slenderness Ratio 180.00
Status SAFE

Check Against Axial Compression For Truss Member

Actual Compressive Stress fc (MPa)


=Fx / Ax 0.93

Calculation Of Allowable Compressive Stress :

Print Time/Date: 07/12/2018 20:09 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 142 of 617
Job No Sheet No Rev
BN/SS/-01 143
Part
Software licensed to BN
Job Title Design of Overhead Gantry Hoarding Truss - 30m Span Ref

By Biswajit Date06-Dec-18 Chd Biswajit


Client Suntony Signage File Final Gantry Truss-30m Date/Time
Span.std 07-Dec-2018 20:06

E (MPa) 200000.00
L/r 70.93
fcc (MPa)
2 2
=π E / λ 392.36
Allowable Compressive Stress fc_allowable (MPa)
1.4 1.4
=0.6fccfy / [(fcc) + (fy) ] 107.66
Interaction ratio
=fc / fc_allowable 0.01
Status SAFE

Print Time/Date: 07/12/2018 20:09 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 143 of 617
Job No Sheet No Rev
BN/SS/-01 144
Part
Software licensed to BN
Job Title Design of Overhead Gantry Hoarding Truss - 30m Span Ref

By Biswajit Date06-Dec-18 Chd Biswajit


Client Suntony Signage File Final Gantry Truss-30m Date/Time
Span.std 07-Dec-2018 20:06

Design Of Member No. 63 As Per IS:800

Input Parameters

Member Section PIP483L

2
Cross Sectional Area Ax (mm ) 414.00
rz (mm) 16.08
ry (mm) 16.08
Unsupported Length - Major Axis For Slenderness Check Lz (mm) 2000.00
Unsupported Length - Minor Axis For Slenderness Check Ly (mm) 2000.00
Yield Stress fy (MPa) 240.00
Allowable Ratio For Interaction Check 1.00

Design Forces

Axial Load Fx (N ) 4532.54


Critical Loadcase No. 3

Details Of Calculation

Slenderness Checking

Lez (mm) 2000.00


Ley (mm) 2000.00
Lez / rz 124.40
Ley / ry 124.40
Actual Slenderness Ratio 124.40
Allowable Slenderness Ratio 180.00
Status SAFE

Check Against Axial Compression For Truss Member

Actual Compressive Stress fc (MPa)


=Fx / Ax 10.95

Calculation Of Allowable Compressive Stress :

Print Time/Date: 07/12/2018 20:09 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 144 of 617
Job No Sheet No Rev
BN/SS/-01 145
Part
Software licensed to BN
Job Title Design of Overhead Gantry Hoarding Truss - 30m Span Ref

By Biswajit Date06-Dec-18 Chd Biswajit


Client Suntony Signage File Final Gantry Truss-30m Date/Time
Span.std 07-Dec-2018 20:06

E (MPa) 200000.00
L/r 124.40
fcc (MPa)
2 2
=π E / λ 127.54
Allowable Compressive Stress fc_allowable (MPa)
1.4 1.4
=0.6fccfy / [(fcc) + (fy) ] 59.79
Interaction ratio
=fc / fc_allowable 0.18
Status SAFE

Print Time/Date: 07/12/2018 20:09 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 145 of 617
Job No Sheet No Rev
BN/SS/-01 146
Part
Software licensed to BN
Job Title Design of Overhead Gantry Hoarding Truss - 30m Span Ref

By Biswajit Date06-Dec-18 Chd Biswajit


Client Suntony Signage File Final Gantry Truss-30m Date/Time
Span.std 07-Dec-2018 20:06

Design Of Member No. 64 As Per IS:800

Input Parameters

Member Section PIP483L

2
Cross Sectional Area Ax (mm ) 414.00
Net section factor 1.00
2
Net Effective Sectional Area Anet (mm ) 414.00
rz (mm) 16.08
ry (mm) 16.08
Unsupported Length - Major Axis For Slenderness Check Lz (mm) 2000.00
Unsupported Length - Minor Axis For Slenderness Check Ly (mm) 2000.00
Yield Stress fy (MPa) 240.00
Allowable Ratio For Interaction Check 1.00

Design Forces

Axial Load Fx (N ) -652.35


Critical Loadcase No. 3

Details Of Calculation

Slenderness Checking

Lez (mm) 2000.00


Ley (mm) 2000.00
Lez / rz 124.40
Ley / ry 124.40
Actual Slenderness Ratio 124.40
Allowable Slenderness Ratio 400.00
Status SAFE

Check Against Axial Tension For Truss Member

Actual Tensile Stress ft (MPa)


=Fx / Anet 1.58

Print Time/Date: 07/12/2018 20:09 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 146 of 617
Job No Sheet No Rev
BN/SS/-01 147
Part
Software licensed to BN
Job Title Design of Overhead Gantry Hoarding Truss - 30m Span Ref

By Biswajit Date06-Dec-18 Chd Biswajit


Client Suntony Signage File Final Gantry Truss-30m Date/Time
Span.std 07-Dec-2018 20:06

Allowable Tensile Stress ft_allowable (MPa)


=0.60fy 144.00
Interaction ratio
=ft / ft_allowable 0.01
Status SAFE

Print Time/Date: 07/12/2018 20:09 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 147 of 617
Job No Sheet No Rev
BN/SS/-01 148
Part
Software licensed to BN
Job Title Design of Overhead Gantry Hoarding Truss - 30m Span Ref

By Biswajit Date06-Dec-18 Chd Biswajit


Client Suntony Signage File Final Gantry Truss-30m Date/Time
Span.std 07-Dec-2018 20:06

Design Of Member No. 65 As Per IS:800

Input Parameters

Member Section PIP424L

2
Cross Sectional Area Ax (mm ) 0.00
rz (mm) 14.10
ry (mm) 14.10
Unsupported Length - Major Axis For Slenderness Check Lz (mm) 1000.00
Unsupported Length - Minor Axis For Slenderness Check Ly (mm) 1000.00
Yield Stress fy (MPa) 0.00
Allowable Ratio For Interaction Check 1.00

Design Forces

Axial Load Fx (N ) 0.00


Critical Loadcase No. 0

Details Of Calculation

Slenderness Checking

Lez (mm) 1000.00


Ley (mm) 1000.00
Lez / rz 70.93
Ley / ry 70.93
Actual Slenderness Ratio 70.93
Allowable Slenderness Ratio 400.00
Status SAFE

Check Against Axial Compression For Truss Member

Actual Compressive Stress fc (MPa)


=Fx / Ax 0.00

Calculation Of Allowable Compressive Stress :

Print Time/Date: 07/12/2018 20:09 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 148 of 617
Job No Sheet No Rev
BN/SS/-01 149
Part
Software licensed to BN
Job Title Design of Overhead Gantry Hoarding Truss - 30m Span Ref

By Biswajit Date06-Dec-18 Chd Biswajit


Client Suntony Signage File Final Gantry Truss-30m Date/Time
Span.std 07-Dec-2018 20:06

E (MPa) 200000.00
L/r 70.93
fcc (MPa)
2 2
=π E / λ 392.36
Allowable Compressive Stress fc_allowable (MPa)
1.4 1.4
=0.6fccfy / [(fcc) + (fy) ] 0.00
Interaction ratio
=fc / fc_allowable 0.00
Status SAFE

Print Time/Date: 07/12/2018 20:09 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 149 of 617
Job No Sheet No Rev
BN/SS/-01 150
Part
Software licensed to BN
Job Title Design of Overhead Gantry Hoarding Truss - 30m Span Ref

By Biswajit Date06-Dec-18 Chd Biswajit


Client Suntony Signage File Final Gantry Truss-30m Date/Time
Span.std 07-Dec-2018 20:06

Design Of Member No. 66 As Per IS:800

Input Parameters

Member Section PIP603L

2
Cross Sectional Area Ax (mm ) 523.00
Net section factor 1.00
2
Net Effective Sectional Area Anet (mm ) 523.00
rz (mm) 20.32
ry (mm) 20.32
Unsupported Length - Major Axis For Slenderness Check Lz (mm) 1802.77
Unsupported Length - Minor Axis For Slenderness Check Ly (mm) 1802.77
Yield Stress fy (MPa) 240.00
Allowable Ratio For Interaction Check 1.00

Design Forces

Axial Load Fx (N ) -7523.81


Critical Loadcase No. 3

Details Of Calculation

Slenderness Checking

Lez (mm) 1802.77


Ley (mm) 1802.77
Lez / rz 88.71
Ley / ry 88.71
Actual Slenderness Ratio 88.71
Allowable Slenderness Ratio 400.00
Status SAFE

Check Against Axial Tension For Truss Member

Actual Tensile Stress ft (MPa)


=Fx / Anet 14.39

Print Time/Date: 07/12/2018 20:09 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 150 of 617
Job No Sheet No Rev
BN/SS/-01 151
Part
Software licensed to BN
Job Title Design of Overhead Gantry Hoarding Truss - 30m Span Ref

By Biswajit Date06-Dec-18 Chd Biswajit


Client Suntony Signage File Final Gantry Truss-30m Date/Time
Span.std 07-Dec-2018 20:06

Allowable Tensile Stress ft_allowable (MPa)


=0.60fy 144.00
Interaction ratio
=ft / ft_allowable 0.10
Status SAFE

Print Time/Date: 07/12/2018 20:09 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 151 of 617
Job No Sheet No Rev
BN/SS/-01 152
Part
Software licensed to BN
Job Title Design of Overhead Gantry Hoarding Truss - 30m Span Ref

By Biswajit Date06-Dec-18 Chd Biswajit


Client Suntony Signage File Final Gantry Truss-30m Date/Time
Span.std 07-Dec-2018 20:06

Design Of Member No. 67 As Per IS:800

Input Parameters

Member Section PIP483L

2
Cross Sectional Area Ax (mm ) 414.00
Net section factor 1.00
2
Net Effective Sectional Area Anet (mm ) 414.00
rz (mm) 16.08
ry (mm) 16.08
Unsupported Length - Major Axis For Slenderness Check Lz (mm) 2500.00
Unsupported Length - Minor Axis For Slenderness Check Ly (mm) 2500.00
Yield Stress fy (MPa) 240.00
Allowable Ratio For Interaction Check 1.00

Design Forces

Axial Load Fx (N ) -5379.14


Critical Loadcase No. 3

Details Of Calculation

Slenderness Checking

Lez (mm) 2500.00


Ley (mm) 2500.00
Lez / rz 155.51
Ley / ry 155.51
Actual Slenderness Ratio 155.51
Allowable Slenderness Ratio 400.00
Status SAFE

Check Against Axial Tension For Truss Member

Actual Tensile Stress ft (MPa)


=Fx / Anet 12.99

Print Time/Date: 07/12/2018 20:09 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 152 of 617
Job No Sheet No Rev
BN/SS/-01 153
Part
Software licensed to BN
Job Title Design of Overhead Gantry Hoarding Truss - 30m Span Ref

By Biswajit Date06-Dec-18 Chd Biswajit


Client Suntony Signage File Final Gantry Truss-30m Date/Time
Span.std 07-Dec-2018 20:06

Allowable Tensile Stress ft_allowable (MPa)


=0.60fy 144.00
Interaction ratio
=ft / ft_allowable 0.09
Status SAFE

Print Time/Date: 07/12/2018 20:09 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 153 of 617
Job No Sheet No Rev
BN/SS/-01 154
Part
Software licensed to BN
Job Title Design of Overhead Gantry Hoarding Truss - 30m Span Ref

By Biswajit Date06-Dec-18 Chd Biswajit


Client Suntony Signage File Final Gantry Truss-30m Date/Time
Span.std 07-Dec-2018 20:06

Design Of Member No. 68 As Per IS:800

Input Parameters

Member Section PIP483L

2
Cross Sectional Area Ax (mm ) 414.00
rz (mm) 16.08
ry (mm) 16.08
Unsupported Length - Major Axis For Slenderness Check Lz (mm) 2500.00
Unsupported Length - Minor Axis For Slenderness Check Ly (mm) 2500.00
Yield Stress fy (MPa) 240.00
Allowable Ratio For Interaction Check 1.00

Design Forces

Axial Load Fx (N ) 1983.63


Critical Loadcase No. 3

Details Of Calculation

Slenderness Checking

Lez (mm) 2500.00


Ley (mm) 2500.00
Lez / rz 155.51
Ley / ry 155.51
Actual Slenderness Ratio 155.51
Allowable Slenderness Ratio 180.00
Status SAFE

Check Against Axial Compression For Truss Member

Actual Compressive Stress fc (MPa)


=Fx / Ax 4.79

Calculation Of Allowable Compressive Stress :

Print Time/Date: 07/12/2018 20:09 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 154 of 617
Job No Sheet No Rev
BN/SS/-01 155
Part
Software licensed to BN
Job Title Design of Overhead Gantry Hoarding Truss - 30m Span Ref

By Biswajit Date06-Dec-18 Chd Biswajit


Client Suntony Signage File Final Gantry Truss-30m Date/Time
Span.std 07-Dec-2018 20:06

E (MPa) 200000.00
L/r 155.51
fcc (MPa)
2 2
=π E / λ 81.63
Allowable Compressive Stress fc_allowable (MPa)
1.4 1.4
=0.6fccfy / [(fcc) + (fy) ] 42.47
Interaction ratio
=fc / fc_allowable 0.11
Status SAFE

Print Time/Date: 07/12/2018 20:09 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 155 of 617
Job No Sheet No Rev
BN/SS/-01 156
Part
Software licensed to BN
Job Title Design of Overhead Gantry Hoarding Truss - 30m Span Ref

By Biswajit Date06-Dec-18 Chd Biswajit


Client Suntony Signage File Final Gantry Truss-30m Date/Time
Span.std 07-Dec-2018 20:06

Design Of Member No. 69 As Per IS:800

Input Parameters

Member Section PIP603L

2
Cross Sectional Area Ax (mm ) 523.00
Net section factor 1.00
2
Net Effective Sectional Area Anet (mm ) 523.00
rz (mm) 20.32
ry (mm) 20.32
Unsupported Length - Major Axis For Slenderness Check Lz (mm) 1802.77
Unsupported Length - Minor Axis For Slenderness Check Ly (mm) 1802.77
Yield Stress fy (MPa) 240.00
Allowable Ratio For Interaction Check 1.00

Design Forces

Axial Load Fx (N ) -9701.82


Critical Loadcase No. 3

Details Of Calculation

Slenderness Checking

Lez (mm) 1802.77


Ley (mm) 1802.77
Lez / rz 88.71
Ley / ry 88.71
Actual Slenderness Ratio 88.71
Allowable Slenderness Ratio 400.00
Status SAFE

Check Against Axial Tension For Truss Member

Actual Tensile Stress ft (MPa)


=Fx / Anet 18.55

Print Time/Date: 07/12/2018 20:09 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 156 of 617
Job No Sheet No Rev
BN/SS/-01 157
Part
Software licensed to BN
Job Title Design of Overhead Gantry Hoarding Truss - 30m Span Ref

By Biswajit Date06-Dec-18 Chd Biswajit


Client Suntony Signage File Final Gantry Truss-30m Date/Time
Span.std 07-Dec-2018 20:06

Allowable Tensile Stress ft_allowable (MPa)


=0.60fy 144.00
Interaction ratio
=ft / ft_allowable 0.13
Status SAFE

Print Time/Date: 07/12/2018 20:09 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 157 of 617
Job No Sheet No Rev
BN/SS/-01 158
Part
Software licensed to BN
Job Title Design of Overhead Gantry Hoarding Truss - 30m Span Ref

By Biswajit Date06-Dec-18 Chd Biswajit


Client Suntony Signage File Final Gantry Truss-30m Date/Time
Span.std 07-Dec-2018 20:06

Design Of Member No. 70 As Per IS:800

Input Parameters

Member Section PIP424L

2
Cross Sectional Area Ax (mm ) 325.00
rz (mm) 14.10
ry (mm) 14.10
Unsupported Length - Major Axis For Slenderness Check Lz (mm) 1000.00
Unsupported Length - Minor Axis For Slenderness Check Ly (mm) 1000.00
Yield Stress fy (MPa) 240.00
Allowable Ratio For Interaction Check 1.00

Design Forces

Axial Load Fx (N ) 1587.00


Critical Loadcase No. 3

Details Of Calculation

Slenderness Checking

Lez (mm) 1000.00


Ley (mm) 1000.00
Lez / rz 70.93
Ley / ry 70.93
Actual Slenderness Ratio 70.93
Allowable Slenderness Ratio 180.00
Status SAFE

Check Against Axial Compression For Truss Member

Actual Compressive Stress fc (MPa)


=Fx / Ax 4.88

Calculation Of Allowable Compressive Stress :

Print Time/Date: 07/12/2018 20:09 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 158 of 617
Job No Sheet No Rev
BN/SS/-01 159
Part
Software licensed to BN
Job Title Design of Overhead Gantry Hoarding Truss - 30m Span Ref

By Biswajit Date06-Dec-18 Chd Biswajit


Client Suntony Signage File Final Gantry Truss-30m Date/Time
Span.std 07-Dec-2018 20:06

E (MPa) 200000.00
L/r 70.93
fcc (MPa)
2 2
=π E / λ 392.36
Allowable Compressive Stress fc_allowable (MPa)
1.4 1.4
=0.6fccfy / [(fcc) + (fy) ] 107.66
Interaction ratio
=fc / fc_allowable 0.05
Status SAFE

Print Time/Date: 07/12/2018 20:09 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 159 of 617
Job No Sheet No Rev
BN/SS/-01 160
Part
Software licensed to BN
Job Title Design of Overhead Gantry Hoarding Truss - 30m Span Ref

By Biswajit Date06-Dec-18 Chd Biswajit


Client Suntony Signage File Final Gantry Truss-30m Date/Time
Span.std 07-Dec-2018 20:06

Design Of Member No. 71 As Per IS:800

Input Parameters

Member Section PIP483L

2
Cross Sectional Area Ax (mm ) 414.00
rz (mm) 16.08
ry (mm) 16.08
Unsupported Length - Major Axis For Slenderness Check Lz (mm) 2000.00
Unsupported Length - Minor Axis For Slenderness Check Ly (mm) 2000.00
Yield Stress fy (MPa) 240.00
Allowable Ratio For Interaction Check 1.00

Design Forces

Axial Load Fx (N ) 3188.36


Critical Loadcase No. 3

Details Of Calculation

Slenderness Checking

Lez (mm) 2000.00


Ley (mm) 2000.00
Lez / rz 124.40
Ley / ry 124.40
Actual Slenderness Ratio 124.40
Allowable Slenderness Ratio 180.00
Status SAFE

Check Against Axial Compression For Truss Member

Actual Compressive Stress fc (MPa)


=Fx / Ax 7.70

Calculation Of Allowable Compressive Stress :

Print Time/Date: 07/12/2018 20:09 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 160 of 617
Job No Sheet No Rev
BN/SS/-01 161
Part
Software licensed to BN
Job Title Design of Overhead Gantry Hoarding Truss - 30m Span Ref

By Biswajit Date06-Dec-18 Chd Biswajit


Client Suntony Signage File Final Gantry Truss-30m Date/Time
Span.std 07-Dec-2018 20:06

E (MPa) 200000.00
L/r 124.40
fcc (MPa)
2 2
=π E / λ 127.54
Allowable Compressive Stress fc_allowable (MPa)
1.4 1.4
=0.6fccfy / [(fcc) + (fy) ] 59.79
Interaction ratio
=fc / fc_allowable 0.13
Status SAFE

Print Time/Date: 07/12/2018 20:09 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 161 of 617
Job No Sheet No Rev
BN/SS/-01 162
Part
Software licensed to BN
Job Title Design of Overhead Gantry Hoarding Truss - 30m Span Ref

By Biswajit Date06-Dec-18 Chd Biswajit


Client Suntony Signage File Final Gantry Truss-30m Date/Time
Span.std 07-Dec-2018 20:06

Design Of Member No. 72 As Per IS:800

Input Parameters

Member Section PIP483L

2
Cross Sectional Area Ax (mm ) 414.00
Net section factor 1.00
2
Net Effective Sectional Area Anet (mm ) 414.00
rz (mm) 16.08
ry (mm) 16.08
Unsupported Length - Major Axis For Slenderness Check Lz (mm) 2000.00
Unsupported Length - Minor Axis For Slenderness Check Ly (mm) 2000.00
Yield Stress fy (MPa) 240.00
Allowable Ratio For Interaction Check 1.00

Design Forces

Axial Load Fx (N ) -1816.13


Critical Loadcase No. 3

Details Of Calculation

Slenderness Checking

Lez (mm) 2000.00


Ley (mm) 2000.00
Lez / rz 124.40
Ley / ry 124.40
Actual Slenderness Ratio 124.40
Allowable Slenderness Ratio 400.00
Status SAFE

Check Against Axial Tension For Truss Member

Actual Tensile Stress ft (MPa)


=Fx / Anet 4.39

Print Time/Date: 07/12/2018 20:09 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 162 of 617
Job No Sheet No Rev
BN/SS/-01 163
Part
Software licensed to BN
Job Title Design of Overhead Gantry Hoarding Truss - 30m Span Ref

By Biswajit Date06-Dec-18 Chd Biswajit


Client Suntony Signage File Final Gantry Truss-30m Date/Time
Span.std 07-Dec-2018 20:06

Allowable Tensile Stress ft_allowable (MPa)


=0.60fy 144.00
Interaction ratio
=ft / ft_allowable 0.03
Status SAFE

Print Time/Date: 07/12/2018 20:09 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 163 of 617
Job No Sheet No Rev
BN/SS/-01 164
Part
Software licensed to BN
Job Title Design of Overhead Gantry Hoarding Truss - 30m Span Ref

By Biswajit Date06-Dec-18 Chd Biswajit


Client Suntony Signage File Final Gantry Truss-30m Date/Time
Span.std 07-Dec-2018 20:06

Design Of Member No. 73 As Per IS:800

Input Parameters

Member Section PIP424L

2
Cross Sectional Area Ax (mm ) 325.00
rz (mm) 14.10
ry (mm) 14.10
Unsupported Length - Major Axis For Slenderness Check Lz (mm) 1000.00
Unsupported Length - Minor Axis For Slenderness Check Ly (mm) 1000.00
Yield Stress fy (MPa) 240.00
Allowable Ratio For Interaction Check 1.00

Design Forces

Axial Load Fx (N ) 1194.15


Critical Loadcase No. 3

Details Of Calculation

Slenderness Checking

Lez (mm) 1000.00


Ley (mm) 1000.00
Lez / rz 70.93
Ley / ry 70.93
Actual Slenderness Ratio 70.93
Allowable Slenderness Ratio 180.00
Status SAFE

Check Against Axial Compression For Truss Member

Actual Compressive Stress fc (MPa)


=Fx / Ax 3.67

Calculation Of Allowable Compressive Stress :

Print Time/Date: 07/12/2018 20:09 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 164 of 617
Job No Sheet No Rev
BN/SS/-01 165
Part
Software licensed to BN
Job Title Design of Overhead Gantry Hoarding Truss - 30m Span Ref

By Biswajit Date06-Dec-18 Chd Biswajit


Client Suntony Signage File Final Gantry Truss-30m Date/Time
Span.std 07-Dec-2018 20:06

E (MPa) 200000.00
L/r 70.93
fcc (MPa)
2 2
=π E / λ 392.36
Allowable Compressive Stress fc_allowable (MPa)
1.4 1.4
=0.6fccfy / [(fcc) + (fy) ] 107.66
Interaction ratio
=fc / fc_allowable 0.03
Status SAFE

Print Time/Date: 07/12/2018 20:09 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 165 of 617
Job No Sheet No Rev
BN/SS/-01 166
Part
Software licensed to BN
Job Title Design of Overhead Gantry Hoarding Truss - 30m Span Ref

By Biswajit Date06-Dec-18 Chd Biswajit


Client Suntony Signage File Final Gantry Truss-30m Date/Time
Span.std 07-Dec-2018 20:06

Design Of Member No. 74 As Per IS:800

Input Parameters

Member Section PIP603L

2
Cross Sectional Area Ax (mm ) 523.00
rz (mm) 20.32
ry (mm) 20.32
Unsupported Length - Major Axis For Slenderness Check Lz (mm) 1802.77
Unsupported Length - Minor Axis For Slenderness Check Ly (mm) 1802.77
Yield Stress fy (MPa) 240.00
Allowable Ratio For Interaction Check 1.00

Design Forces

Axial Load Fx (N ) 3954.59


Critical Loadcase No. 3

Details Of Calculation

Slenderness Checking

Lez (mm) 1802.77


Ley (mm) 1802.77
Lez / rz 88.71
Ley / ry 88.71
Actual Slenderness Ratio 88.71
Allowable Slenderness Ratio 180.00
Status SAFE

Check Against Axial Compression For Truss Member

Actual Compressive Stress fc (MPa)


=Fx / Ax 7.56

Calculation Of Allowable Compressive Stress :

Print Time/Date: 07/12/2018 20:09 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 166 of 617
Job No Sheet No Rev
BN/SS/-01 167
Part
Software licensed to BN
Job Title Design of Overhead Gantry Hoarding Truss - 30m Span Ref

By Biswajit Date06-Dec-18 Chd Biswajit


Client Suntony Signage File Final Gantry Truss-30m Date/Time
Span.std 07-Dec-2018 20:06

E (MPa) 200000.00
L/r 88.71
fcc (MPa)
2 2
=π E / λ 250.84
Allowable Compressive Stress fc_allowable (MPa)
1.4 1.4
=0.6fccfy / [(fcc) + (fy) ] 89.69
Interaction ratio
=fc / fc_allowable 0.08
Status SAFE

Print Time/Date: 07/12/2018 20:09 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 167 of 617
Job No Sheet No Rev
BN/SS/-01 168
Part
Software licensed to BN
Job Title Design of Overhead Gantry Hoarding Truss - 30m Span Ref

By Biswajit Date06-Dec-18 Chd Biswajit


Client Suntony Signage File Final Gantry Truss-30m Date/Time
Span.std 07-Dec-2018 20:06

Design Of Member No. 75 As Per IS:800

Input Parameters

Member Section PIP483L

2
Cross Sectional Area Ax (mm ) 414.00
Net section factor 1.00
2
Net Effective Sectional Area Anet (mm ) 414.00
rz (mm) 16.08
ry (mm) 16.08
Unsupported Length - Major Axis For Slenderness Check Lz (mm) 2500.00
Unsupported Length - Minor Axis For Slenderness Check Ly (mm) 2500.00
Yield Stress fy (MPa) 240.00
Allowable Ratio For Interaction Check 1.00

Design Forces

Axial Load Fx (N ) -3603.86


Critical Loadcase No. 3

Details Of Calculation

Slenderness Checking

Lez (mm) 2500.00


Ley (mm) 2500.00
Lez / rz 155.51
Ley / ry 155.51
Actual Slenderness Ratio 155.51
Allowable Slenderness Ratio 400.00
Status SAFE

Check Against Axial Tension For Truss Member

Actual Tensile Stress ft (MPa)


=Fx / Anet 8.70

Print Time/Date: 07/12/2018 20:09 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 168 of 617
Job No Sheet No Rev
BN/SS/-01 169
Part
Software licensed to BN
Job Title Design of Overhead Gantry Hoarding Truss - 30m Span Ref

By Biswajit Date06-Dec-18 Chd Biswajit


Client Suntony Signage File Final Gantry Truss-30m Date/Time
Span.std 07-Dec-2018 20:06

Allowable Tensile Stress ft_allowable (MPa)


=0.60fy 144.00
Interaction ratio
=ft / ft_allowable 0.06
Status SAFE

Print Time/Date: 07/12/2018 20:09 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 169 of 617
Job No Sheet No Rev
BN/SS/-01 170
Part
Software licensed to BN
Job Title Design of Overhead Gantry Hoarding Truss - 30m Span Ref

By Biswajit Date06-Dec-18 Chd Biswajit


Client Suntony Signage File Final Gantry Truss-30m Date/Time
Span.std 07-Dec-2018 20:06

Design Of Member No. 76 As Per IS:800

Input Parameters

Member Section PIP483L

2
Cross Sectional Area Ax (mm ) 414.00
rz (mm) 16.08
ry (mm) 16.08
Unsupported Length - Major Axis For Slenderness Check Lz (mm) 2500.00
Unsupported Length - Minor Axis For Slenderness Check Ly (mm) 2500.00
Yield Stress fy (MPa) 240.00
Allowable Ratio For Interaction Check 1.00

Design Forces

Axial Load Fx (N ) 1604.53


Critical Loadcase No. 3

Details Of Calculation

Slenderness Checking

Lez (mm) 2500.00


Ley (mm) 2500.00
Lez / rz 155.51
Ley / ry 155.51
Actual Slenderness Ratio 155.51
Allowable Slenderness Ratio 180.00
Status SAFE

Check Against Axial Compression For Truss Member

Actual Compressive Stress fc (MPa)


=Fx / Ax 3.88

Calculation Of Allowable Compressive Stress :

Print Time/Date: 07/12/2018 20:09 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 170 of 617
Job No Sheet No Rev
BN/SS/-01 171
Part
Software licensed to BN
Job Title Design of Overhead Gantry Hoarding Truss - 30m Span Ref

By Biswajit Date06-Dec-18 Chd Biswajit


Client Suntony Signage File Final Gantry Truss-30m Date/Time
Span.std 07-Dec-2018 20:06

E (MPa) 200000.00
L/r 155.51
fcc (MPa)
2 2
=π E / λ 81.63
Allowable Compressive Stress fc_allowable (MPa)
1.4 1.4
=0.6fccfy / [(fcc) + (fy) ] 42.47
Interaction ratio
=fc / fc_allowable 0.09
Status SAFE

Print Time/Date: 07/12/2018 20:09 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 171 of 617
Job No Sheet No Rev
BN/SS/-01 172
Part
Software licensed to BN
Job Title Design of Overhead Gantry Hoarding Truss - 30m Span Ref

By Biswajit Date06-Dec-18 Chd Biswajit


Client Suntony Signage File Final Gantry Truss-30m Date/Time
Span.std 07-Dec-2018 20:06

Design Of Member No. 77 As Per IS:800

Input Parameters

Member Section PIP603L

2
Cross Sectional Area Ax (mm ) 523.00
rz (mm) 20.32
ry (mm) 20.32
Unsupported Length - Major Axis For Slenderness Check Lz (mm) 1802.77
Unsupported Length - Minor Axis For Slenderness Check Ly (mm) 1802.77
Yield Stress fy (MPa) 240.00
Allowable Ratio For Interaction Check 1.00

Design Forces

Axial Load Fx (N ) 7549.04


Critical Loadcase No. 3

Details Of Calculation

Slenderness Checking

Lez (mm) 1802.77


Ley (mm) 1802.77
Lez / rz 88.71
Ley / ry 88.71
Actual Slenderness Ratio 88.71
Allowable Slenderness Ratio 180.00
Status SAFE

Check Against Axial Compression For Truss Member

Actual Compressive Stress fc (MPa)


=Fx / Ax 14.43

Calculation Of Allowable Compressive Stress :

Print Time/Date: 07/12/2018 20:09 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 172 of 617
Job No Sheet No Rev
BN/SS/-01 173
Part
Software licensed to BN
Job Title Design of Overhead Gantry Hoarding Truss - 30m Span Ref

By Biswajit Date06-Dec-18 Chd Biswajit


Client Suntony Signage File Final Gantry Truss-30m Date/Time
Span.std 07-Dec-2018 20:06

E (MPa) 200000.00
L/r 88.71
fcc (MPa)
2 2
=π E / λ 250.84
Allowable Compressive Stress fc_allowable (MPa)
1.4 1.4
=0.6fccfy / [(fcc) + (fy) ] 89.69
Interaction ratio
=fc / fc_allowable 0.16
Status SAFE

Print Time/Date: 07/12/2018 20:09 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 173 of 617
Job No Sheet No Rev
BN/SS/-01 174
Part
Software licensed to BN
Job Title Design of Overhead Gantry Hoarding Truss - 30m Span Ref

By Biswajit Date06-Dec-18 Chd Biswajit


Client Suntony Signage File Final Gantry Truss-30m Date/Time
Span.std 07-Dec-2018 20:06

Design Of Member No. 78 As Per IS:800

Input Parameters

Member Section PIP424L

2
Cross Sectional Area Ax (mm ) 325.00
rz (mm) 14.10
ry (mm) 14.10
Unsupported Length - Major Axis For Slenderness Check Lz (mm) 1000.00
Unsupported Length - Minor Axis For Slenderness Check Ly (mm) 1000.00
Yield Stress fy (MPa) 240.00
Allowable Ratio For Interaction Check 1.00

Design Forces

Axial Load Fx (N ) 377.01


Critical Loadcase No. 3

Details Of Calculation

Slenderness Checking

Lez (mm) 1000.00


Ley (mm) 1000.00
Lez / rz 70.93
Ley / ry 70.93
Actual Slenderness Ratio 70.93
Allowable Slenderness Ratio 180.00
Status SAFE

Check Against Axial Compression For Truss Member

Actual Compressive Stress fc (MPa)


=Fx / Ax 1.16

Calculation Of Allowable Compressive Stress :

Print Time/Date: 07/12/2018 20:09 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 174 of 617
Job No Sheet No Rev
BN/SS/-01 175
Part
Software licensed to BN
Job Title Design of Overhead Gantry Hoarding Truss - 30m Span Ref

By Biswajit Date06-Dec-18 Chd Biswajit


Client Suntony Signage File Final Gantry Truss-30m Date/Time
Span.std 07-Dec-2018 20:06

E (MPa) 200000.00
L/r 70.93
fcc (MPa)
2 2
=π E / λ 392.36
Allowable Compressive Stress fc_allowable (MPa)
1.4 1.4
=0.6fccfy / [(fcc) + (fy) ] 107.66
Interaction ratio
=fc / fc_allowable 0.01
Status SAFE

Print Time/Date: 07/12/2018 20:09 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 175 of 617
Job No Sheet No Rev
BN/SS/-01 176
Part
Software licensed to BN
Job Title Design of Overhead Gantry Hoarding Truss - 30m Span Ref

By Biswajit Date06-Dec-18 Chd Biswajit


Client Suntony Signage File Final Gantry Truss-30m Date/Time
Span.std 07-Dec-2018 20:06

Design Of Member No. 79 As Per IS:800

Input Parameters

Member Section PIP483L

2
Cross Sectional Area Ax (mm ) 414.00
rz (mm) 16.08
ry (mm) 16.08
Unsupported Length - Major Axis For Slenderness Check Lz (mm) 2000.00
Unsupported Length - Minor Axis For Slenderness Check Ly (mm) 2000.00
Yield Stress fy (MPa) 240.00
Allowable Ratio For Interaction Check 1.00

Design Forces

Axial Load Fx (N ) 3383.91


Critical Loadcase No. 3

Details Of Calculation

Slenderness Checking

Lez (mm) 2000.00


Ley (mm) 2000.00
Lez / rz 124.40
Ley / ry 124.40
Actual Slenderness Ratio 124.40
Allowable Slenderness Ratio 180.00
Status SAFE

Check Against Axial Compression For Truss Member

Actual Compressive Stress fc (MPa)


=Fx / Ax 8.17

Calculation Of Allowable Compressive Stress :

Print Time/Date: 07/12/2018 20:09 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 176 of 617
Job No Sheet No Rev
BN/SS/-01 177
Part
Software licensed to BN
Job Title Design of Overhead Gantry Hoarding Truss - 30m Span Ref

By Biswajit Date06-Dec-18 Chd Biswajit


Client Suntony Signage File Final Gantry Truss-30m Date/Time
Span.std 07-Dec-2018 20:06

E (MPa) 200000.00
L/r 124.40
fcc (MPa)
2 2
=π E / λ 127.54
Allowable Compressive Stress fc_allowable (MPa)
1.4 1.4
=0.6fccfy / [(fcc) + (fy) ] 59.79
Interaction ratio
=fc / fc_allowable 0.14
Status SAFE

Print Time/Date: 07/12/2018 20:09 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 177 of 617
Job No Sheet No Rev
BN/SS/-01 178
Part
Software licensed to BN
Job Title Design of Overhead Gantry Hoarding Truss - 30m Span Ref

By Biswajit Date06-Dec-18 Chd Biswajit


Client Suntony Signage File Final Gantry Truss-30m Date/Time
Span.std 07-Dec-2018 20:06

Design Of Member No. 80 As Per IS:800

Input Parameters

Member Section PIP483L

2
Cross Sectional Area Ax (mm ) 414.00
Net section factor 1.00
2
Net Effective Sectional Area Anet (mm ) 414.00
rz (mm) 16.08
ry (mm) 16.08
Unsupported Length - Major Axis For Slenderness Check Lz (mm) 2000.00
Unsupported Length - Minor Axis For Slenderness Check Ly (mm) 2000.00
Yield Stress fy (MPa) 240.00
Allowable Ratio For Interaction Check 1.00

Design Forces

Axial Load Fx (N ) -1588.89


Critical Loadcase No. 3

Details Of Calculation

Slenderness Checking

Lez (mm) 2000.00


Ley (mm) 2000.00
Lez / rz 124.40
Ley / ry 124.40
Actual Slenderness Ratio 124.40
Allowable Slenderness Ratio 400.00
Status SAFE

Check Against Axial Tension For Truss Member

Actual Tensile Stress ft (MPa)


=Fx / Anet 3.84

Print Time/Date: 07/12/2018 20:09 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 178 of 617
Job No Sheet No Rev
BN/SS/-01 179
Part
Software licensed to BN
Job Title Design of Overhead Gantry Hoarding Truss - 30m Span Ref

By Biswajit Date06-Dec-18 Chd Biswajit


Client Suntony Signage File Final Gantry Truss-30m Date/Time
Span.std 07-Dec-2018 20:06

Allowable Tensile Stress ft_allowable (MPa)


=0.60fy 144.00
Interaction ratio
=ft / ft_allowable 0.03
Status SAFE

Print Time/Date: 07/12/2018 20:09 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 179 of 617
Job No Sheet No Rev
BN/SS/-01 180
Part
Software licensed to BN
Job Title Design of Overhead Gantry Hoarding Truss - 30m Span Ref

By Biswajit Date06-Dec-18 Chd Biswajit


Client Suntony Signage File Final Gantry Truss-30m Date/Time
Span.std 07-Dec-2018 20:06

Design Of Member No. 81 As Per IS:800

Input Parameters

Member Section PIP424L

2
Cross Sectional Area Ax (mm ) 0.00
rz (mm) 14.10
ry (mm) 14.10
Unsupported Length - Major Axis For Slenderness Check Lz (mm) 1000.00
Unsupported Length - Minor Axis For Slenderness Check Ly (mm) 1000.00
Yield Stress fy (MPa) 0.00
Allowable Ratio For Interaction Check 1.00

Design Forces

Axial Load Fx (N ) 0.00


Critical Loadcase No. 0

Details Of Calculation

Slenderness Checking

Lez (mm) 1000.00


Ley (mm) 1000.00
Lez / rz 70.93
Ley / ry 70.93
Actual Slenderness Ratio 70.93
Allowable Slenderness Ratio 400.00
Status SAFE

Check Against Axial Compression For Truss Member

Actual Compressive Stress fc (MPa)


=Fx / Ax 0.00

Calculation Of Allowable Compressive Stress :

Print Time/Date: 07/12/2018 20:09 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 180 of 617
Job No Sheet No Rev
BN/SS/-01 181
Part
Software licensed to BN
Job Title Design of Overhead Gantry Hoarding Truss - 30m Span Ref

By Biswajit Date06-Dec-18 Chd Biswajit


Client Suntony Signage File Final Gantry Truss-30m Date/Time
Span.std 07-Dec-2018 20:06

E (MPa) 200000.00
L/r 70.93
fcc (MPa)
2 2
=π E / λ 392.36
Allowable Compressive Stress fc_allowable (MPa)
1.4 1.4
=0.6fccfy / [(fcc) + (fy) ] 0.00
Interaction ratio
=fc / fc_allowable 0.00
Status SAFE

Print Time/Date: 07/12/2018 20:09 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 181 of 617
Job No Sheet No Rev
BN/SS/-01 182
Part
Software licensed to BN
Job Title Design of Overhead Gantry Hoarding Truss - 30m Span Ref

By Biswajit Date06-Dec-18 Chd Biswajit


Client Suntony Signage File Final Gantry Truss-30m Date/Time
Span.std 07-Dec-2018 20:06

Design Of Member No. 82 As Per IS:800

Input Parameters

Member Section PIP603L

2
Cross Sectional Area Ax (mm ) 523.00
Net section factor 1.00
2
Net Effective Sectional Area Anet (mm ) 523.00
rz (mm) 20.32
ry (mm) 20.32
Unsupported Length - Major Axis For Slenderness Check Lz (mm) 1802.77
Unsupported Length - Minor Axis For Slenderness Check Ly (mm) 1802.77
Yield Stress fy (MPa) 240.00
Allowable Ratio For Interaction Check 1.00

Design Forces

Axial Load Fx (N ) -1773.24


Critical Loadcase No. 3

Details Of Calculation

Slenderness Checking

Lez (mm) 1802.77


Ley (mm) 1802.77
Lez / rz 88.71
Ley / ry 88.71
Actual Slenderness Ratio 88.71
Allowable Slenderness Ratio 400.00
Status SAFE

Check Against Axial Tension For Truss Member

Actual Tensile Stress ft (MPa)


=Fx / Anet 3.39

Print Time/Date: 07/12/2018 20:09 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 182 of 617
Job No Sheet No Rev
BN/SS/-01 183
Part
Software licensed to BN
Job Title Design of Overhead Gantry Hoarding Truss - 30m Span Ref

By Biswajit Date06-Dec-18 Chd Biswajit


Client Suntony Signage File Final Gantry Truss-30m Date/Time
Span.std 07-Dec-2018 20:06

Allowable Tensile Stress ft_allowable (MPa)


=0.60fy 144.00
Interaction ratio
=ft / ft_allowable 0.02
Status SAFE

Print Time/Date: 07/12/2018 20:09 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 183 of 617
Job No Sheet No Rev
BN/SS/-01 184
Part
Software licensed to BN
Job Title Design of Overhead Gantry Hoarding Truss - 30m Span Ref

By Biswajit Date06-Dec-18 Chd Biswajit


Client Suntony Signage File Final Gantry Truss-30m Date/Time
Span.std 07-Dec-2018 20:06

Design Of Member No. 83 As Per IS:800

Input Parameters

Member Section PIP483L

2
Cross Sectional Area Ax (mm ) 414.00
Net section factor 1.00
2
Net Effective Sectional Area Anet (mm ) 414.00
rz (mm) 16.08
ry (mm) 16.08
Unsupported Length - Major Axis For Slenderness Check Lz (mm) 2500.00
Unsupported Length - Minor Axis For Slenderness Check Ly (mm) 2500.00
Yield Stress fy (MPa) 240.00
Allowable Ratio For Interaction Check 1.00

Design Forces

Axial Load Fx (N ) -3943.36


Critical Loadcase No. 3

Details Of Calculation

Slenderness Checking

Lez (mm) 2500.00


Ley (mm) 2500.00
Lez / rz 155.51
Ley / ry 155.51
Actual Slenderness Ratio 155.51
Allowable Slenderness Ratio 400.00
Status SAFE

Check Against Axial Tension For Truss Member

Actual Tensile Stress ft (MPa)


=Fx / Anet 9.53

Print Time/Date: 07/12/2018 20:09 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 184 of 617
Job No Sheet No Rev
BN/SS/-01 185
Part
Software licensed to BN
Job Title Design of Overhead Gantry Hoarding Truss - 30m Span Ref

By Biswajit Date06-Dec-18 Chd Biswajit


Client Suntony Signage File Final Gantry Truss-30m Date/Time
Span.std 07-Dec-2018 20:06

Allowable Tensile Stress ft_allowable (MPa)


=0.60fy 144.00
Interaction ratio
=ft / ft_allowable 0.07
Status SAFE

Print Time/Date: 07/12/2018 20:09 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 185 of 617
Job No Sheet No Rev
BN/SS/-01 186
Part
Software licensed to BN
Job Title Design of Overhead Gantry Hoarding Truss - 30m Span Ref

By Biswajit Date06-Dec-18 Chd Biswajit


Client Suntony Signage File Final Gantry Truss-30m Date/Time
Span.std 07-Dec-2018 20:06

Design Of Member No. 84 As Per IS:800

Input Parameters

Member Section PIP483L

2
Cross Sectional Area Ax (mm ) 414.00
rz (mm) 16.08
ry (mm) 16.08
Unsupported Length - Major Axis For Slenderness Check Lz (mm) 2500.00
Unsupported Length - Minor Axis For Slenderness Check Ly (mm) 2500.00
Yield Stress fy (MPa) 240.00
Allowable Ratio For Interaction Check 1.00

Design Forces

Axial Load Fx (N ) 3340.20


Critical Loadcase No. 3

Details Of Calculation

Slenderness Checking

Lez (mm) 2500.00


Ley (mm) 2500.00
Lez / rz 155.51
Ley / ry 155.51
Actual Slenderness Ratio 155.51
Allowable Slenderness Ratio 180.00
Status SAFE

Check Against Axial Compression For Truss Member

Actual Compressive Stress fc (MPa)


=Fx / Ax 8.07

Calculation Of Allowable Compressive Stress :

Print Time/Date: 07/12/2018 20:09 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 186 of 617
Job No Sheet No Rev
BN/SS/-01 187
Part
Software licensed to BN
Job Title Design of Overhead Gantry Hoarding Truss - 30m Span Ref

By Biswajit Date06-Dec-18 Chd Biswajit


Client Suntony Signage File Final Gantry Truss-30m Date/Time
Span.std 07-Dec-2018 20:06

E (MPa) 200000.00
L/r 155.51
fcc (MPa)
2 2
=π E / λ 81.63
Allowable Compressive Stress fc_allowable (MPa)
1.4 1.4
=0.6fccfy / [(fcc) + (fy) ] 42.47
Interaction ratio
=fc / fc_allowable 0.19
Status SAFE

Print Time/Date: 07/12/2018 20:09 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 187 of 617
Job No Sheet No Rev
BN/SS/-01 188
Part
Software licensed to BN
Job Title Design of Overhead Gantry Hoarding Truss - 30m Span Ref

By Biswajit Date06-Dec-18 Chd Biswajit


Client Suntony Signage File Final Gantry Truss-30m Date/Time
Span.std 07-Dec-2018 20:06

Design Of Member No. 85 As Per IS:800

Input Parameters

Member Section PIP603L

2
Cross Sectional Area Ax (mm ) 523.00
Net section factor 1.00
2
Net Effective Sectional Area Anet (mm ) 523.00
rz (mm) 20.32
ry (mm) 20.32
Unsupported Length - Major Axis For Slenderness Check Lz (mm) 1802.77
Unsupported Length - Minor Axis For Slenderness Check Ly (mm) 1802.77
Yield Stress fy (MPa) 240.00
Allowable Ratio For Interaction Check 1.00

Design Forces

Axial Load Fx (N ) -4008.37


Critical Loadcase No. 3

Details Of Calculation

Slenderness Checking

Lez (mm) 1802.77


Ley (mm) 1802.77
Lez / rz 88.71
Ley / ry 88.71
Actual Slenderness Ratio 88.71
Allowable Slenderness Ratio 400.00
Status SAFE

Check Against Axial Tension For Truss Member

Actual Tensile Stress ft (MPa)


=Fx / Anet 7.66

Print Time/Date: 07/12/2018 20:09 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 188 of 617
Job No Sheet No Rev
BN/SS/-01 189
Part
Software licensed to BN
Job Title Design of Overhead Gantry Hoarding Truss - 30m Span Ref

By Biswajit Date06-Dec-18 Chd Biswajit


Client Suntony Signage File Final Gantry Truss-30m Date/Time
Span.std 07-Dec-2018 20:06

Allowable Tensile Stress ft_allowable (MPa)


=0.60fy 144.00
Interaction ratio
=ft / ft_allowable 0.05
Status SAFE

Print Time/Date: 07/12/2018 20:09 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 189 of 617
Job No Sheet No Rev
BN/SS/-01 190
Part
Software licensed to BN
Job Title Design of Overhead Gantry Hoarding Truss - 30m Span Ref

By Biswajit Date06-Dec-18 Chd Biswajit


Client Suntony Signage File Final Gantry Truss-30m Date/Time
Span.std 07-Dec-2018 20:06

Design Of Member No. 86 As Per IS:800

Input Parameters

Member Section PIP424L

2
Cross Sectional Area Ax (mm ) 325.00
rz (mm) 14.10
ry (mm) 14.10
Unsupported Length - Major Axis For Slenderness Check Lz (mm) 1000.00
Unsupported Length - Minor Axis For Slenderness Check Ly (mm) 1000.00
Yield Stress fy (MPa) 240.00
Allowable Ratio For Interaction Check 1.00

Design Forces

Axial Load Fx (N ) 1587.00


Critical Loadcase No. 3

Details Of Calculation

Slenderness Checking

Lez (mm) 1000.00


Ley (mm) 1000.00
Lez / rz 70.93
Ley / ry 70.93
Actual Slenderness Ratio 70.93
Allowable Slenderness Ratio 180.00
Status SAFE

Check Against Axial Compression For Truss Member

Actual Compressive Stress fc (MPa)


=Fx / Ax 4.88

Calculation Of Allowable Compressive Stress :

Print Time/Date: 07/12/2018 20:09 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 190 of 617
Job No Sheet No Rev
BN/SS/-01 191
Part
Software licensed to BN
Job Title Design of Overhead Gantry Hoarding Truss - 30m Span Ref

By Biswajit Date06-Dec-18 Chd Biswajit


Client Suntony Signage File Final Gantry Truss-30m Date/Time
Span.std 07-Dec-2018 20:06

E (MPa) 200000.00
L/r 70.93
fcc (MPa)
2 2
=π E / λ 392.36
Allowable Compressive Stress fc_allowable (MPa)
1.4 1.4
=0.6fccfy / [(fcc) + (fy) ] 107.66
Interaction ratio
=fc / fc_allowable 0.05
Status SAFE

Print Time/Date: 07/12/2018 20:09 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 191 of 617
Job No Sheet No Rev
BN/SS/-01 192
Part
Software licensed to BN
Job Title Design of Overhead Gantry Hoarding Truss - 30m Span Ref

By Biswajit Date06-Dec-18 Chd Biswajit


Client Suntony Signage File Final Gantry Truss-30m Date/Time
Span.std 07-Dec-2018 20:06

Design Of Member No. 87 As Per IS:800

Input Parameters

Member Section PIP483L

2
Cross Sectional Area Ax (mm ) 414.00
rz (mm) 16.08
ry (mm) 16.08
Unsupported Length - Major Axis For Slenderness Check Lz (mm) 2000.00
Unsupported Length - Minor Axis For Slenderness Check Ly (mm) 2000.00
Yield Stress fy (MPa) 240.00
Allowable Ratio For Interaction Check 1.00

Design Forces

Axial Load Fx (N ) 2011.95


Critical Loadcase No. 3

Details Of Calculation

Slenderness Checking

Lez (mm) 2000.00


Ley (mm) 2000.00
Lez / rz 124.40
Ley / ry 124.40
Actual Slenderness Ratio 124.40
Allowable Slenderness Ratio 180.00
Status SAFE

Check Against Axial Compression For Truss Member

Actual Compressive Stress fc (MPa)


=Fx / Ax 4.86

Calculation Of Allowable Compressive Stress :

Print Time/Date: 07/12/2018 20:09 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 192 of 617
Job No Sheet No Rev
BN/SS/-01 193
Part
Software licensed to BN
Job Title Design of Overhead Gantry Hoarding Truss - 30m Span Ref

By Biswajit Date06-Dec-18 Chd Biswajit


Client Suntony Signage File Final Gantry Truss-30m Date/Time
Span.std 07-Dec-2018 20:06

E (MPa) 200000.00
L/r 124.40
fcc (MPa)
2 2
=π E / λ 127.54
Allowable Compressive Stress fc_allowable (MPa)
1.4 1.4
=0.6fccfy / [(fcc) + (fy) ] 59.79
Interaction ratio
=fc / fc_allowable 0.08
Status SAFE

Print Time/Date: 07/12/2018 20:09 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 193 of 617
Job No Sheet No Rev
BN/SS/-01 194
Part
Software licensed to BN
Job Title Design of Overhead Gantry Hoarding Truss - 30m Span Ref

By Biswajit Date06-Dec-18 Chd Biswajit


Client Suntony Signage File Final Gantry Truss-30m Date/Time
Span.std 07-Dec-2018 20:06

Design Of Member No. 88 As Per IS:800

Input Parameters

Member Section PIP483L

2
Cross Sectional Area Ax (mm ) 414.00
Net section factor 1.00
2
Net Effective Sectional Area Anet (mm ) 414.00
rz (mm) 16.08
ry (mm) 16.08
Unsupported Length - Major Axis For Slenderness Check Lz (mm) 2000.00
Unsupported Length - Minor Axis For Slenderness Check Ly (mm) 2000.00
Yield Stress fy (MPa) 240.00
Allowable Ratio For Interaction Check 1.00

Design Forces

Axial Load Fx (N ) -2901.38


Critical Loadcase No. 3

Details Of Calculation

Slenderness Checking

Lez (mm) 2000.00


Ley (mm) 2000.00
Lez / rz 124.40
Ley / ry 124.40
Actual Slenderness Ratio 124.40
Allowable Slenderness Ratio 400.00
Status SAFE

Check Against Axial Tension For Truss Member

Actual Tensile Stress ft (MPa)


=Fx / Anet 7.01

Print Time/Date: 07/12/2018 20:09 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 194 of 617
Job No Sheet No Rev
BN/SS/-01 195
Part
Software licensed to BN
Job Title Design of Overhead Gantry Hoarding Truss - 30m Span Ref

By Biswajit Date06-Dec-18 Chd Biswajit


Client Suntony Signage File Final Gantry Truss-30m Date/Time
Span.std 07-Dec-2018 20:06

Allowable Tensile Stress ft_allowable (MPa)


=0.60fy 144.00
Interaction ratio
=ft / ft_allowable 0.05
Status SAFE

Print Time/Date: 07/12/2018 20:09 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 195 of 617
Job No Sheet No Rev
BN/SS/-01 196
Part
Software licensed to BN
Job Title Design of Overhead Gantry Hoarding Truss - 30m Span Ref

By Biswajit Date06-Dec-18 Chd Biswajit


Client Suntony Signage File Final Gantry Truss-30m Date/Time
Span.std 07-Dec-2018 20:06

Design Of Member No. 89 As Per IS:800

Input Parameters

Member Section PIP424L

2
Cross Sectional Area Ax (mm ) 325.00
rz (mm) 14.10
ry (mm) 14.10
Unsupported Length - Major Axis For Slenderness Check Lz (mm) 1000.00
Unsupported Length - Minor Axis For Slenderness Check Ly (mm) 1000.00
Yield Stress fy (MPa) 240.00
Allowable Ratio For Interaction Check 1.00

Design Forces

Axial Load Fx (N ) 1180.26


Critical Loadcase No. 3

Details Of Calculation

Slenderness Checking

Lez (mm) 1000.00


Ley (mm) 1000.00
Lez / rz 70.93
Ley / ry 70.93
Actual Slenderness Ratio 70.93
Allowable Slenderness Ratio 180.00
Status SAFE

Check Against Axial Compression For Truss Member

Actual Compressive Stress fc (MPa)


=Fx / Ax 3.63

Calculation Of Allowable Compressive Stress :

Print Time/Date: 07/12/2018 20:09 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 196 of 617
Job No Sheet No Rev
BN/SS/-01 197
Part
Software licensed to BN
Job Title Design of Overhead Gantry Hoarding Truss - 30m Span Ref

By Biswajit Date06-Dec-18 Chd Biswajit


Client Suntony Signage File Final Gantry Truss-30m Date/Time
Span.std 07-Dec-2018 20:06

E (MPa) 200000.00
L/r 70.93
fcc (MPa)
2 2
=π E / λ 392.36
Allowable Compressive Stress fc_allowable (MPa)
1.4 1.4
=0.6fccfy / [(fcc) + (fy) ] 107.66
Interaction ratio
=fc / fc_allowable 0.03
Status SAFE

Print Time/Date: 07/12/2018 20:09 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 197 of 617
Job No Sheet No Rev
BN/SS/-01 198
Part
Software licensed to BN
Job Title Design of Overhead Gantry Hoarding Truss - 30m Span Ref

By Biswajit Date06-Dec-18 Chd Biswajit


Client Suntony Signage File Final Gantry Truss-30m Date/Time
Span.std 07-Dec-2018 20:06

Design Of Member No. 90 As Per IS:800

Input Parameters

Member Section PIP603L

2
Cross Sectional Area Ax (mm ) 523.00
Net section factor 1.00
2
Net Effective Sectional Area Anet (mm ) 523.00
rz (mm) 20.32
ry (mm) 20.32
Unsupported Length - Major Axis For Slenderness Check Lz (mm) 1802.77
Unsupported Length - Minor Axis For Slenderness Check Ly (mm) 1802.77
Yield Stress fy (MPa) 240.00
Allowable Ratio For Interaction Check 1.00

Design Forces

Axial Load Fx (N ) -1821.03


Critical Loadcase No. 3

Details Of Calculation

Slenderness Checking

Lez (mm) 1802.77


Ley (mm) 1802.77
Lez / rz 88.71
Ley / ry 88.71
Actual Slenderness Ratio 88.71
Allowable Slenderness Ratio 400.00
Status SAFE

Check Against Axial Tension For Truss Member

Actual Tensile Stress ft (MPa)


=Fx / Anet 3.48

Print Time/Date: 07/12/2018 20:09 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 198 of 617
Job No Sheet No Rev
BN/SS/-01 199
Part
Software licensed to BN
Job Title Design of Overhead Gantry Hoarding Truss - 30m Span Ref

By Biswajit Date06-Dec-18 Chd Biswajit


Client Suntony Signage File Final Gantry Truss-30m Date/Time
Span.std 07-Dec-2018 20:06

Allowable Tensile Stress ft_allowable (MPa)


=0.60fy 144.00
Interaction ratio
=ft / ft_allowable 0.02
Status SAFE

Print Time/Date: 07/12/2018 20:09 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 199 of 617
Job No Sheet No Rev
BN/SS/-01 200
Part
Software licensed to BN
Job Title Design of Overhead Gantry Hoarding Truss - 30m Span Ref

By Biswajit Date06-Dec-18 Chd Biswajit


Client Suntony Signage File Final Gantry Truss-30m Date/Time
Span.std 07-Dec-2018 20:06

Design Of Member No. 91 As Per IS:800

Input Parameters

Member Section PIP483L

2
Cross Sectional Area Ax (mm ) 414.00
Net section factor 1.00
2
Net Effective Sectional Area Anet (mm ) 414.00
rz (mm) 16.08
ry (mm) 16.08
Unsupported Length - Major Axis For Slenderness Check Lz (mm) 2500.00
Unsupported Length - Minor Axis For Slenderness Check Ly (mm) 2500.00
Yield Stress fy (MPa) 240.00
Allowable Ratio For Interaction Check 1.00

Design Forces

Axial Load Fx (N ) -2133.35


Critical Loadcase No. 3

Details Of Calculation

Slenderness Checking

Lez (mm) 2500.00


Ley (mm) 2500.00
Lez / rz 155.51
Ley / ry 155.51
Actual Slenderness Ratio 155.51
Allowable Slenderness Ratio 400.00
Status SAFE

Check Against Axial Tension For Truss Member

Actual Tensile Stress ft (MPa)


=Fx / Anet 5.15

Print Time/Date: 07/12/2018 20:09 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 200 of 617
Job No Sheet No Rev
BN/SS/-01 201
Part
Software licensed to BN
Job Title Design of Overhead Gantry Hoarding Truss - 30m Span Ref

By Biswajit Date06-Dec-18 Chd Biswajit


Client Suntony Signage File Final Gantry Truss-30m Date/Time
Span.std 07-Dec-2018 20:06

Allowable Tensile Stress ft_allowable (MPa)


=0.60fy 144.00
Interaction ratio
=ft / ft_allowable 0.04
Status SAFE

Print Time/Date: 07/12/2018 20:09 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 201 of 617
Job No Sheet No Rev
BN/SS/-01 202
Part
Software licensed to BN
Job Title Design of Overhead Gantry Hoarding Truss - 30m Span Ref

By Biswajit Date06-Dec-18 Chd Biswajit


Client Suntony Signage File Final Gantry Truss-30m Date/Time
Span.std 07-Dec-2018 20:06

Design Of Member No. 92 As Per IS:800

Input Parameters

Member Section PIP483L

2
Cross Sectional Area Ax (mm ) 414.00
rz (mm) 16.08
ry (mm) 16.08
Unsupported Length - Major Axis For Slenderness Check Lz (mm) 2500.00
Unsupported Length - Minor Axis For Slenderness Check Ly (mm) 2500.00
Yield Stress fy (MPa) 240.00
Allowable Ratio For Interaction Check 1.00

Design Forces

Axial Load Fx (N ) 2926.37


Critical Loadcase No. 3

Details Of Calculation

Slenderness Checking

Lez (mm) 2500.00


Ley (mm) 2500.00
Lez / rz 155.51
Ley / ry 155.51
Actual Slenderness Ratio 155.51
Allowable Slenderness Ratio 180.00
Status SAFE

Check Against Axial Compression For Truss Member

Actual Compressive Stress fc (MPa)


=Fx / Ax 7.07

Calculation Of Allowable Compressive Stress :

Print Time/Date: 07/12/2018 20:09 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 202 of 617
Job No Sheet No Rev
BN/SS/-01 203
Part
Software licensed to BN
Job Title Design of Overhead Gantry Hoarding Truss - 30m Span Ref

By Biswajit Date06-Dec-18 Chd Biswajit


Client Suntony Signage File Final Gantry Truss-30m Date/Time
Span.std 07-Dec-2018 20:06

E (MPa) 200000.00
L/r 155.51
fcc (MPa)
2 2
=π E / λ 81.63
Allowable Compressive Stress fc_allowable (MPa)
1.4 1.4
=0.6fccfy / [(fcc) + (fy) ] 42.47
Interaction ratio
=fc / fc_allowable 0.17
Status SAFE

Print Time/Date: 07/12/2018 20:09 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 203 of 617
Job No Sheet No Rev
BN/SS/-01 204
Part
Software licensed to BN
Job Title Design of Overhead Gantry Hoarding Truss - 30m Span Ref

By Biswajit Date06-Dec-18 Chd Biswajit


Client Suntony Signage File Final Gantry Truss-30m Date/Time
Span.std 07-Dec-2018 20:06

Design Of Member No. 93 As Per IS:800

Input Parameters

Member Section PIP603L

2
Cross Sectional Area Ax (mm ) 523.00
rz (mm) 20.32
ry (mm) 20.32
Unsupported Length - Major Axis For Slenderness Check Lz (mm) 1802.77
Unsupported Length - Minor Axis For Slenderness Check Ly (mm) 1802.77
Yield Stress fy (MPa) 240.00
Allowable Ratio For Interaction Check 1.00

Design Forces

Axial Load Fx (N ) 1880.63


Critical Loadcase No. 3

Details Of Calculation

Slenderness Checking

Lez (mm) 1802.77


Ley (mm) 1802.77
Lez / rz 88.71
Ley / ry 88.71
Actual Slenderness Ratio 88.71
Allowable Slenderness Ratio 180.00
Status SAFE

Check Against Axial Compression For Truss Member

Actual Compressive Stress fc (MPa)


=Fx / Ax 3.60

Calculation Of Allowable Compressive Stress :

Print Time/Date: 07/12/2018 20:09 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 204 of 617
Job No Sheet No Rev
BN/SS/-01 205
Part
Software licensed to BN
Job Title Design of Overhead Gantry Hoarding Truss - 30m Span Ref

By Biswajit Date06-Dec-18 Chd Biswajit


Client Suntony Signage File Final Gantry Truss-30m Date/Time
Span.std 07-Dec-2018 20:06

E (MPa) 200000.00
L/r 88.71
fcc (MPa)
2 2
=π E / λ 250.84
Allowable Compressive Stress fc_allowable (MPa)
1.4 1.4
=0.6fccfy / [(fcc) + (fy) ] 89.69
Interaction ratio
=fc / fc_allowable 0.04
Status SAFE

Print Time/Date: 07/12/2018 20:09 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 205 of 617
Job No Sheet No Rev
BN/SS/-01 206
Part
Software licensed to BN
Job Title Design of Overhead Gantry Hoarding Truss - 30m Span Ref

By Biswajit Date06-Dec-18 Chd Biswajit


Client Suntony Signage File Final Gantry Truss-30m Date/Time
Span.std 07-Dec-2018 20:06

Design Of Member No. 94 As Per IS:800

Input Parameters

Member Section PIP424L

2
Cross Sectional Area Ax (mm ) 325.00
rz (mm) 14.10
ry (mm) 14.10
Unsupported Length - Major Axis For Slenderness Check Lz (mm) 1000.00
Unsupported Length - Minor Axis For Slenderness Check Ly (mm) 1000.00
Yield Stress fy (MPa) 240.00
Allowable Ratio For Interaction Check 1.00

Design Forces

Axial Load Fx (N ) 375.47


Critical Loadcase No. 3

Details Of Calculation

Slenderness Checking

Lez (mm) 1000.00


Ley (mm) 1000.00
Lez / rz 70.93
Ley / ry 70.93
Actual Slenderness Ratio 70.93
Allowable Slenderness Ratio 180.00
Status SAFE

Check Against Axial Compression For Truss Member

Actual Compressive Stress fc (MPa)


=Fx / Ax 1.16

Calculation Of Allowable Compressive Stress :

Print Time/Date: 07/12/2018 20:09 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 206 of 617
Job No Sheet No Rev
BN/SS/-01 207
Part
Software licensed to BN
Job Title Design of Overhead Gantry Hoarding Truss - 30m Span Ref

By Biswajit Date06-Dec-18 Chd Biswajit


Client Suntony Signage File Final Gantry Truss-30m Date/Time
Span.std 07-Dec-2018 20:06

E (MPa) 200000.00
L/r 70.93
fcc (MPa)
2 2
=π E / λ 392.36
Allowable Compressive Stress fc_allowable (MPa)
1.4 1.4
=0.6fccfy / [(fcc) + (fy) ] 107.66
Interaction ratio
=fc / fc_allowable 0.01
Status SAFE

Print Time/Date: 07/12/2018 20:09 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 207 of 617
Job No Sheet No Rev
BN/SS/-01 208
Part
Software licensed to BN
Job Title Design of Overhead Gantry Hoarding Truss - 30m Span Ref

By Biswajit Date06-Dec-18 Chd Biswajit


Client Suntony Signage File Final Gantry Truss-30m Date/Time
Span.std 07-Dec-2018 20:06

Design Of Member No. 95 As Per IS:800

Input Parameters

Member Section PIP483L

2
Cross Sectional Area Ax (mm ) 414.00
rz (mm) 16.08
ry (mm) 16.08
Unsupported Length - Major Axis For Slenderness Check Lz (mm) 2000.00
Unsupported Length - Minor Axis For Slenderness Check Ly (mm) 2000.00
Yield Stress fy (MPa) 240.00
Allowable Ratio For Interaction Check 1.00

Design Forces

Axial Load Fx (N ) 2204.42


Critical Loadcase No. 3

Details Of Calculation

Slenderness Checking

Lez (mm) 2000.00


Ley (mm) 2000.00
Lez / rz 124.40
Ley / ry 124.40
Actual Slenderness Ratio 124.40
Allowable Slenderness Ratio 180.00
Status SAFE

Check Against Axial Compression For Truss Member

Actual Compressive Stress fc (MPa)


=Fx / Ax 5.32

Calculation Of Allowable Compressive Stress :

Print Time/Date: 07/12/2018 20:09 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 208 of 617
Job No Sheet No Rev
BN/SS/-01 209
Part
Software licensed to BN
Job Title Design of Overhead Gantry Hoarding Truss - 30m Span Ref

By Biswajit Date06-Dec-18 Chd Biswajit


Client Suntony Signage File Final Gantry Truss-30m Date/Time
Span.std 07-Dec-2018 20:06

E (MPa) 200000.00
L/r 124.40
fcc (MPa)
2 2
=π E / λ 127.54
Allowable Compressive Stress fc_allowable (MPa)
1.4 1.4
=0.6fccfy / [(fcc) + (fy) ] 59.79
Interaction ratio
=fc / fc_allowable 0.09
Status SAFE

Print Time/Date: 07/12/2018 20:09 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 209 of 617
Job No Sheet No Rev
BN/SS/-01 210
Part
Software licensed to BN
Job Title Design of Overhead Gantry Hoarding Truss - 30m Span Ref

By Biswajit Date06-Dec-18 Chd Biswajit


Client Suntony Signage File Final Gantry Truss-30m Date/Time
Span.std 07-Dec-2018 20:06

Design Of Member No. 96 As Per IS:800

Input Parameters

Member Section PIP483L

2
Cross Sectional Area Ax (mm ) 414.00
Net section factor 1.00
2
Net Effective Sectional Area Anet (mm ) 414.00
rz (mm) 16.08
ry (mm) 16.08
Unsupported Length - Major Axis For Slenderness Check Lz (mm) 2000.00
Unsupported Length - Minor Axis For Slenderness Check Ly (mm) 2000.00
Yield Stress fy (MPa) 240.00
Allowable Ratio For Interaction Check 1.00

Design Forces

Axial Load Fx (N ) -2646.37


Critical Loadcase No. 3

Details Of Calculation

Slenderness Checking

Lez (mm) 2000.00


Ley (mm) 2000.00
Lez / rz 124.40
Ley / ry 124.40
Actual Slenderness Ratio 124.40
Allowable Slenderness Ratio 400.00
Status SAFE

Check Against Axial Tension For Truss Member

Actual Tensile Stress ft (MPa)


=Fx / Anet 6.39

Print Time/Date: 07/12/2018 20:09 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 210 of 617
Job No Sheet No Rev
BN/SS/-01 211
Part
Software licensed to BN
Job Title Design of Overhead Gantry Hoarding Truss - 30m Span Ref

By Biswajit Date06-Dec-18 Chd Biswajit


Client Suntony Signage File Final Gantry Truss-30m Date/Time
Span.std 07-Dec-2018 20:06

Allowable Tensile Stress ft_allowable (MPa)


=0.60fy 144.00
Interaction ratio
=ft / ft_allowable 0.04
Status SAFE

Print Time/Date: 07/12/2018 20:09 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 211 of 617
Job No Sheet No Rev
BN/SS/-01 212
Part
Software licensed to BN
Job Title Design of Overhead Gantry Hoarding Truss - 30m Span Ref

By Biswajit Date06-Dec-18 Chd Biswajit


Client Suntony Signage File Final Gantry Truss-30m Date/Time
Span.std 07-Dec-2018 20:06

Design Of Member No. 97 As Per IS:800

Input Parameters

Member Section PIP424L

2
Cross Sectional Area Ax (mm ) 0.00
rz (mm) 14.10
ry (mm) 14.10
Unsupported Length - Major Axis For Slenderness Check Lz (mm) 1000.00
Unsupported Length - Minor Axis For Slenderness Check Ly (mm) 1000.00
Yield Stress fy (MPa) 0.00
Allowable Ratio For Interaction Check 1.00

Design Forces

Axial Load Fx (N ) 0.00


Critical Loadcase No. 0

Details Of Calculation

Slenderness Checking

Lez (mm) 1000.00


Ley (mm) 1000.00
Lez / rz 70.93
Ley / ry 70.93
Actual Slenderness Ratio 70.93
Allowable Slenderness Ratio 400.00
Status SAFE

Check Against Axial Compression For Truss Member

Actual Compressive Stress fc (MPa)


=Fx / Ax 0.00

Calculation Of Allowable Compressive Stress :

Print Time/Date: 07/12/2018 20:09 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 212 of 617
Job No Sheet No Rev
BN/SS/-01 213
Part
Software licensed to BN
Job Title Design of Overhead Gantry Hoarding Truss - 30m Span Ref

By Biswajit Date06-Dec-18 Chd Biswajit


Client Suntony Signage File Final Gantry Truss-30m Date/Time
Span.std 07-Dec-2018 20:06

E (MPa) 200000.00
L/r 70.93
fcc (MPa)
2 2
=π E / λ 392.36
Allowable Compressive Stress fc_allowable (MPa)
1.4 1.4
=0.6fccfy / [(fcc) + (fy) ] 0.00
Interaction ratio
=fc / fc_allowable 0.00
Status SAFE

Print Time/Date: 07/12/2018 20:09 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 213 of 617
Job No Sheet No Rev
BN/SS/-01 214
Part
Software licensed to BN
Job Title Design of Overhead Gantry Hoarding Truss - 30m Span Ref

By Biswajit Date06-Dec-18 Chd Biswajit


Client Suntony Signage File Final Gantry Truss-30m Date/Time
Span.std 07-Dec-2018 20:06

Design Of Member No. 98 As Per IS:800

Input Parameters

Member Section PIP603L

2
Cross Sectional Area Ax (mm ) 523.00
rz (mm) 20.32
ry (mm) 20.32
Unsupported Length - Major Axis For Slenderness Check Lz (mm) 1802.77
Unsupported Length - Minor Axis For Slenderness Check Ly (mm) 1802.77
Yield Stress fy (MPa) 240.00
Allowable Ratio For Interaction Check 1.00

Design Forces

Axial Load Fx (N ) 4005.15


Critical Loadcase No. 3

Details Of Calculation

Slenderness Checking

Lez (mm) 1802.77


Ley (mm) 1802.77
Lez / rz 88.71
Ley / ry 88.71
Actual Slenderness Ratio 88.71
Allowable Slenderness Ratio 180.00
Status SAFE

Check Against Axial Compression For Truss Member

Actual Compressive Stress fc (MPa)


=Fx / Ax 7.66

Calculation Of Allowable Compressive Stress :

Print Time/Date: 07/12/2018 20:09 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 214 of 617
Job No Sheet No Rev
BN/SS/-01 215
Part
Software licensed to BN
Job Title Design of Overhead Gantry Hoarding Truss - 30m Span Ref

By Biswajit Date06-Dec-18 Chd Biswajit


Client Suntony Signage File Final Gantry Truss-30m Date/Time
Span.std 07-Dec-2018 20:06

E (MPa) 200000.00
L/r 88.71
fcc (MPa)
2 2
=π E / λ 250.84
Allowable Compressive Stress fc_allowable (MPa)
1.4 1.4
=0.6fccfy / [(fcc) + (fy) ] 89.69
Interaction ratio
=fc / fc_allowable 0.09
Status SAFE

Print Time/Date: 07/12/2018 20:09 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 215 of 617
Job No Sheet No Rev
BN/SS/-01 216
Part
Software licensed to BN
Job Title Design of Overhead Gantry Hoarding Truss - 30m Span Ref

By Biswajit Date06-Dec-18 Chd Biswajit


Client Suntony Signage File Final Gantry Truss-30m Date/Time
Span.std 07-Dec-2018 20:06

Design Of Member No. 99 As Per IS:800

Input Parameters

Member Section PIP483L

2
Cross Sectional Area Ax (mm ) 414.00
Net section factor 1.00
2
Net Effective Sectional Area Anet (mm ) 414.00
rz (mm) 16.08
ry (mm) 16.08
Unsupported Length - Major Axis For Slenderness Check Lz (mm) 2500.00
Unsupported Length - Minor Axis For Slenderness Check Ly (mm) 2500.00
Yield Stress fy (MPa) 240.00
Allowable Ratio For Interaction Check 1.00

Design Forces

Axial Load Fx (N ) -2468.99


Critical Loadcase No. 3

Details Of Calculation

Slenderness Checking

Lez (mm) 2500.00


Ley (mm) 2500.00
Lez / rz 155.51
Ley / ry 155.51
Actual Slenderness Ratio 155.51
Allowable Slenderness Ratio 400.00
Status SAFE

Check Against Axial Tension For Truss Member

Actual Tensile Stress ft (MPa)


=Fx / Anet 5.96

Print Time/Date: 07/12/2018 20:09 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 216 of 617
Job No Sheet No Rev
BN/SS/-01 217
Part
Software licensed to BN
Job Title Design of Overhead Gantry Hoarding Truss - 30m Span Ref

By Biswajit Date06-Dec-18 Chd Biswajit


Client Suntony Signage File Final Gantry Truss-30m Date/Time
Span.std 07-Dec-2018 20:06

Allowable Tensile Stress ft_allowable (MPa)


=0.60fy 144.00
Interaction ratio
=ft / ft_allowable 0.04
Status SAFE

Print Time/Date: 07/12/2018 20:09 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 217 of 617
Job No Sheet No Rev
BN/SS/-01 218
Part
Software licensed to BN
Job Title Design of Overhead Gantry Hoarding Truss - 30m Span Ref

By Biswajit Date06-Dec-18 Chd Biswajit


Client Suntony Signage File Final Gantry Truss-30m Date/Time
Span.std 07-Dec-2018 20:06

Design Of Member No. 100 As Per IS:800

Input Parameters

Member Section PIP483L

2
Cross Sectional Area Ax (mm ) 414.00
rz (mm) 16.08
ry (mm) 16.08
Unsupported Length - Major Axis For Slenderness Check Lz (mm) 2500.00
Unsupported Length - Minor Axis For Slenderness Check Ly (mm) 2500.00
Yield Stress fy (MPa) 240.00
Allowable Ratio For Interaction Check 1.00

Design Forces

Axial Load Fx (N ) 4658.19


Critical Loadcase No. 3

Details Of Calculation

Slenderness Checking

Lez (mm) 2500.00


Ley (mm) 2500.00
Lez / rz 155.51
Ley / ry 155.51
Actual Slenderness Ratio 155.51
Allowable Slenderness Ratio 180.00
Status SAFE

Check Against Axial Compression For Truss Member

Actual Compressive Stress fc (MPa)


=Fx / Ax 11.25

Calculation Of Allowable Compressive Stress :

Print Time/Date: 07/12/2018 20:09 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 218 of 617
Job No Sheet No Rev
BN/SS/-01 219
Part
Software licensed to BN
Job Title Design of Overhead Gantry Hoarding Truss - 30m Span Ref

By Biswajit Date06-Dec-18 Chd Biswajit


Client Suntony Signage File Final Gantry Truss-30m Date/Time
Span.std 07-Dec-2018 20:06

E (MPa) 200000.00
L/r 155.51
fcc (MPa)
2 2
=π E / λ 81.63
Allowable Compressive Stress fc_allowable (MPa)
1.4 1.4
=0.6fccfy / [(fcc) + (fy) ] 42.47
Interaction ratio
=fc / fc_allowable 0.26
Status SAFE

Print Time/Date: 07/12/2018 20:09 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 219 of 617
Job No Sheet No Rev
BN/SS/-01 220
Part
Software licensed to BN
Job Title Design of Overhead Gantry Hoarding Truss - 30m Span Ref

By Biswajit Date06-Dec-18 Chd Biswajit


Client Suntony Signage File Final Gantry Truss-30m Date/Time
Span.std 07-Dec-2018 20:06

Design Of Member No. 101 As Per IS:800

Input Parameters

Member Section PIP603L

2
Cross Sectional Area Ax (mm ) 523.00
rz (mm) 20.32
ry (mm) 20.32
Unsupported Length - Major Axis For Slenderness Check Lz (mm) 1802.77
Unsupported Length - Minor Axis For Slenderness Check Ly (mm) 1802.77
Yield Stress fy (MPa) 240.00
Allowable Ratio For Interaction Check 1.00

Design Forces

Axial Load Fx (N ) 1657.26


Critical Loadcase No. 3

Details Of Calculation

Slenderness Checking

Lez (mm) 1802.77


Ley (mm) 1802.77
Lez / rz 88.71
Ley / ry 88.71
Actual Slenderness Ratio 88.71
Allowable Slenderness Ratio 180.00
Status SAFE

Check Against Axial Compression For Truss Member

Actual Compressive Stress fc (MPa)


=Fx / Ax 3.17

Calculation Of Allowable Compressive Stress :

Print Time/Date: 07/12/2018 20:09 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 220 of 617
Job No Sheet No Rev
BN/SS/-01 221
Part
Software licensed to BN
Job Title Design of Overhead Gantry Hoarding Truss - 30m Span Ref

By Biswajit Date06-Dec-18 Chd Biswajit


Client Suntony Signage File Final Gantry Truss-30m Date/Time
Span.std 07-Dec-2018 20:06

E (MPa) 200000.00
L/r 88.71
fcc (MPa)
2 2
=π E / λ 250.84
Allowable Compressive Stress fc_allowable (MPa)
1.4 1.4
=0.6fccfy / [(fcc) + (fy) ] 89.69
Interaction ratio
=fc / fc_allowable 0.04
Status SAFE

Print Time/Date: 07/12/2018 20:09 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 221 of 617
Job No Sheet No Rev
BN/SS/-01 222
Part
Software licensed to BN
Job Title Design of Overhead Gantry Hoarding Truss - 30m Span Ref

By Biswajit Date06-Dec-18 Chd Biswajit


Client Suntony Signage File Final Gantry Truss-30m Date/Time
Span.std 07-Dec-2018 20:06

Design Of Member No. 102 As Per IS:800

Input Parameters

Member Section PIP424L

2
Cross Sectional Area Ax (mm ) 325.00
rz (mm) 14.10
ry (mm) 14.10
Unsupported Length - Major Axis For Slenderness Check Lz (mm) 1000.00
Unsupported Length - Minor Axis For Slenderness Check Ly (mm) 1000.00
Yield Stress fy (MPa) 240.00
Allowable Ratio For Interaction Check 1.00

Design Forces

Axial Load Fx (N ) 1587.00


Critical Loadcase No. 3

Details Of Calculation

Slenderness Checking

Lez (mm) 1000.00


Ley (mm) 1000.00
Lez / rz 70.93
Ley / ry 70.93
Actual Slenderness Ratio 70.93
Allowable Slenderness Ratio 180.00
Status SAFE

Check Against Axial Compression For Truss Member

Actual Compressive Stress fc (MPa)


=Fx / Ax 4.88

Calculation Of Allowable Compressive Stress :

Print Time/Date: 07/12/2018 20:09 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 222 of 617
Job No Sheet No Rev
BN/SS/-01 223
Part
Software licensed to BN
Job Title Design of Overhead Gantry Hoarding Truss - 30m Span Ref

By Biswajit Date06-Dec-18 Chd Biswajit


Client Suntony Signage File Final Gantry Truss-30m Date/Time
Span.std 07-Dec-2018 20:06

E (MPa) 200000.00
L/r 70.93
fcc (MPa)
2 2
=π E / λ 392.36
Allowable Compressive Stress fc_allowable (MPa)
1.4 1.4
=0.6fccfy / [(fcc) + (fy) ] 107.66
Interaction ratio
=fc / fc_allowable 0.05
Status SAFE

Print Time/Date: 07/12/2018 20:09 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 223 of 617
Job No Sheet No Rev
BN/SS/-01 224
Part
Software licensed to BN
Job Title Design of Overhead Gantry Hoarding Truss - 30m Span Ref

By Biswajit Date06-Dec-18 Chd Biswajit


Client Suntony Signage File Final Gantry Truss-30m Date/Time
Span.std 07-Dec-2018 20:06

Design Of Member No. 103 As Per IS:800

Input Parameters

Member Section PIP483L

2
Cross Sectional Area Ax (mm ) 414.00
rz (mm) 16.08
ry (mm) 16.08
Unsupported Length - Major Axis For Slenderness Check Lz (mm) 2000.00
Unsupported Length - Minor Axis For Slenderness Check Ly (mm) 2000.00
Yield Stress fy (MPa) 240.00
Allowable Ratio For Interaction Check 1.00

Design Forces

Axial Load Fx (N ) 868.34


Critical Loadcase No. 3

Details Of Calculation

Slenderness Checking

Lez (mm) 2000.00


Ley (mm) 2000.00
Lez / rz 124.40
Ley / ry 124.40
Actual Slenderness Ratio 124.40
Allowable Slenderness Ratio 180.00
Status SAFE

Check Against Axial Compression For Truss Member

Actual Compressive Stress fc (MPa)


=Fx / Ax 2.10

Calculation Of Allowable Compressive Stress :

Print Time/Date: 07/12/2018 20:09 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 224 of 617
Job No Sheet No Rev
BN/SS/-01 225
Part
Software licensed to BN
Job Title Design of Overhead Gantry Hoarding Truss - 30m Span Ref

By Biswajit Date06-Dec-18 Chd Biswajit


Client Suntony Signage File Final Gantry Truss-30m Date/Time
Span.std 07-Dec-2018 20:06

E (MPa) 200000.00
L/r 124.40
fcc (MPa)
2 2
=π E / λ 127.54
Allowable Compressive Stress fc_allowable (MPa)
1.4 1.4
=0.6fccfy / [(fcc) + (fy) ] 59.79
Interaction ratio
=fc / fc_allowable 0.04
Status SAFE

Print Time/Date: 07/12/2018 20:09 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 225 of 617
Job No Sheet No Rev
BN/SS/-01 226
Part
Software licensed to BN
Job Title Design of Overhead Gantry Hoarding Truss - 30m Span Ref

By Biswajit Date06-Dec-18 Chd Biswajit


Client Suntony Signage File Final Gantry Truss-30m Date/Time
Span.std 07-Dec-2018 20:06

Design Of Member No. 104 As Per IS:800

Input Parameters

Member Section PIP483L

2
Cross Sectional Area Ax (mm ) 414.00
Net section factor 1.00
2
Net Effective Sectional Area Anet (mm ) 414.00
rz (mm) 16.08
ry (mm) 16.08
Unsupported Length - Major Axis For Slenderness Check Lz (mm) 2000.00
Unsupported Length - Minor Axis For Slenderness Check Ly (mm) 2000.00
Yield Stress fy (MPa) 240.00
Allowable Ratio For Interaction Check 1.00

Design Forces

Axial Load Fx (N ) -3955.77


Critical Loadcase No. 3

Details Of Calculation

Slenderness Checking

Lez (mm) 2000.00


Ley (mm) 2000.00
Lez / rz 124.40
Ley / ry 124.40
Actual Slenderness Ratio 124.40
Allowable Slenderness Ratio 400.00
Status SAFE

Check Against Axial Tension For Truss Member

Actual Tensile Stress ft (MPa)


=Fx / Anet 9.56

Print Time/Date: 07/12/2018 20:09 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 226 of 617
Job No Sheet No Rev
BN/SS/-01 227
Part
Software licensed to BN
Job Title Design of Overhead Gantry Hoarding Truss - 30m Span Ref

By Biswajit Date06-Dec-18 Chd Biswajit


Client Suntony Signage File Final Gantry Truss-30m Date/Time
Span.std 07-Dec-2018 20:06

Allowable Tensile Stress ft_allowable (MPa)


=0.60fy 144.00
Interaction ratio
=ft / ft_allowable 0.07
Status SAFE

Print Time/Date: 07/12/2018 20:09 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 227 of 617
Job No Sheet No Rev
BN/SS/-01 228
Part
Software licensed to BN
Job Title Design of Overhead Gantry Hoarding Truss - 30m Span Ref

By Biswajit Date06-Dec-18 Chd Biswajit


Client Suntony Signage File Final Gantry Truss-30m Date/Time
Span.std 07-Dec-2018 20:06

Design Of Member No. 105 As Per IS:800

Input Parameters

Member Section PIP424L

2
Cross Sectional Area Ax (mm ) 325.00
rz (mm) 14.10
ry (mm) 14.10
Unsupported Length - Major Axis For Slenderness Check Lz (mm) 1000.00
Unsupported Length - Minor Axis For Slenderness Check Ly (mm) 1000.00
Yield Stress fy (MPa) 240.00
Allowable Ratio For Interaction Check 1.00

Design Forces

Axial Load Fx (N ) 1198.20


Critical Loadcase No. 3

Details Of Calculation

Slenderness Checking

Lez (mm) 1000.00


Ley (mm) 1000.00
Lez / rz 70.93
Ley / ry 70.93
Actual Slenderness Ratio 70.93
Allowable Slenderness Ratio 180.00
Status SAFE

Check Against Axial Compression For Truss Member

Actual Compressive Stress fc (MPa)


=Fx / Ax 3.69

Calculation Of Allowable Compressive Stress :

Print Time/Date: 07/12/2018 20:09 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 228 of 617
Job No Sheet No Rev
BN/SS/-01 229
Part
Software licensed to BN
Job Title Design of Overhead Gantry Hoarding Truss - 30m Span Ref

By Biswajit Date06-Dec-18 Chd Biswajit


Client Suntony Signage File Final Gantry Truss-30m Date/Time
Span.std 07-Dec-2018 20:06

E (MPa) 200000.00
L/r 70.93
fcc (MPa)
2 2
=π E / λ 392.36
Allowable Compressive Stress fc_allowable (MPa)
1.4 1.4
=0.6fccfy / [(fcc) + (fy) ] 107.66
Interaction ratio
=fc / fc_allowable 0.03
Status SAFE

Print Time/Date: 07/12/2018 20:09 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 229 of 617
Job No Sheet No Rev
BN/SS/-01 230
Part
Software licensed to BN
Job Title Design of Overhead Gantry Hoarding Truss - 30m Span Ref

By Biswajit Date06-Dec-18 Chd Biswajit


Client Suntony Signage File Final Gantry Truss-30m Date/Time
Span.std 07-Dec-2018 20:06

Design Of Member No. 106 As Per IS:800

Input Parameters

Member Section PIP603L

2
Cross Sectional Area Ax (mm ) 523.00
Net section factor 1.00
2
Net Effective Sectional Area Anet (mm ) 523.00
rz (mm) 20.32
ry (mm) 20.32
Unsupported Length - Major Axis For Slenderness Check Lz (mm) 1802.77
Unsupported Length - Minor Axis For Slenderness Check Ly (mm) 1802.77
Yield Stress fy (MPa) 240.00
Allowable Ratio For Interaction Check 1.00

Design Forces

Axial Load Fx (N ) -7567.08


Critical Loadcase No. 3

Details Of Calculation

Slenderness Checking

Lez (mm) 1802.77


Ley (mm) 1802.77
Lez / rz 88.71
Ley / ry 88.71
Actual Slenderness Ratio 88.71
Allowable Slenderness Ratio 400.00
Status SAFE

Check Against Axial Tension For Truss Member

Actual Tensile Stress ft (MPa)


=Fx / Anet 14.47

Print Time/Date: 07/12/2018 20:09 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 230 of 617
Job No Sheet No Rev
BN/SS/-01 231
Part
Software licensed to BN
Job Title Design of Overhead Gantry Hoarding Truss - 30m Span Ref

By Biswajit Date06-Dec-18 Chd Biswajit


Client Suntony Signage File Final Gantry Truss-30m Date/Time
Span.std 07-Dec-2018 20:06

Allowable Tensile Stress ft_allowable (MPa)


=0.60fy 144.00
Interaction ratio
=ft / ft_allowable 0.10
Status SAFE

Print Time/Date: 07/12/2018 20:09 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 231 of 617
Job No Sheet No Rev
BN/SS/-01 232
Part
Software licensed to BN
Job Title Design of Overhead Gantry Hoarding Truss - 30m Span Ref

By Biswajit Date06-Dec-18 Chd Biswajit


Client Suntony Signage File Final Gantry Truss-30m Date/Time
Span.std 07-Dec-2018 20:06

Design Of Member No. 107 As Per IS:800

Input Parameters

Member Section PIP483L

2
Cross Sectional Area Ax (mm ) 414.00
Net section factor 1.00
2
Net Effective Sectional Area Anet (mm ) 414.00
rz (mm) 16.08
ry (mm) 16.08
Unsupported Length - Major Axis For Slenderness Check Lz (mm) 2500.00
Unsupported Length - Minor Axis For Slenderness Check Ly (mm) 2500.00
Yield Stress fy (MPa) 240.00
Allowable Ratio For Interaction Check 1.00

Design Forces

Axial Load Fx (N ) -703.84


Critical Loadcase No. 3

Details Of Calculation

Slenderness Checking

Lez (mm) 2500.00


Ley (mm) 2500.00
Lez / rz 155.51
Ley / ry 155.51
Actual Slenderness Ratio 155.51
Allowable Slenderness Ratio 400.00
Status SAFE

Check Against Axial Tension For Truss Member

Actual Tensile Stress ft (MPa)


=Fx / Anet 1.70

Print Time/Date: 07/12/2018 20:09 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 232 of 617
Job No Sheet No Rev
BN/SS/-01 233
Part
Software licensed to BN
Job Title Design of Overhead Gantry Hoarding Truss - 30m Span Ref

By Biswajit Date06-Dec-18 Chd Biswajit


Client Suntony Signage File Final Gantry Truss-30m Date/Time
Span.std 07-Dec-2018 20:06

Allowable Tensile Stress ft_allowable (MPa)


=0.60fy 144.00
Interaction ratio
=ft / ft_allowable 0.01
Status SAFE

Print Time/Date: 07/12/2018 20:09 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 233 of 617
Job No Sheet No Rev
BN/SS/-01 234
Part
Software licensed to BN
Job Title Design of Overhead Gantry Hoarding Truss - 30m Span Ref

By Biswajit Date06-Dec-18 Chd Biswajit


Client Suntony Signage File Final Gantry Truss-30m Date/Time
Span.std 07-Dec-2018 20:06

Design Of Member No. 108 As Per IS:800

Input Parameters

Member Section PIP483L

2
Cross Sectional Area Ax (mm ) 414.00
rz (mm) 16.08
ry (mm) 16.08
Unsupported Length - Major Axis For Slenderness Check Lz (mm) 2500.00
Unsupported Length - Minor Axis For Slenderness Check Ly (mm) 2500.00
Yield Stress fy (MPa) 240.00
Allowable Ratio For Interaction Check 1.00

Design Forces

Axial Load Fx (N ) 4289.20


Critical Loadcase No. 3

Details Of Calculation

Slenderness Checking

Lez (mm) 2500.00


Ley (mm) 2500.00
Lez / rz 155.51
Ley / ry 155.51
Actual Slenderness Ratio 155.51
Allowable Slenderness Ratio 180.00
Status SAFE

Check Against Axial Compression For Truss Member

Actual Compressive Stress fc (MPa)


=Fx / Ax 10.36

Calculation Of Allowable Compressive Stress :

Print Time/Date: 07/12/2018 20:09 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 234 of 617
Job No Sheet No Rev
BN/SS/-01 235
Part
Software licensed to BN
Job Title Design of Overhead Gantry Hoarding Truss - 30m Span Ref

By Biswajit Date06-Dec-18 Chd Biswajit


Client Suntony Signage File Final Gantry Truss-30m Date/Time
Span.std 07-Dec-2018 20:06

E (MPa) 200000.00
L/r 155.51
fcc (MPa)
2 2
=π E / λ 81.63
Allowable Compressive Stress fc_allowable (MPa)
1.4 1.4
=0.6fccfy / [(fcc) + (fy) ] 42.47
Interaction ratio
=fc / fc_allowable 0.24
Status SAFE

Print Time/Date: 07/12/2018 20:09 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 235 of 617
Job No Sheet No Rev
BN/SS/-01 236
Part
Software licensed to BN
Job Title Design of Overhead Gantry Hoarding Truss - 30m Span Ref

By Biswajit Date06-Dec-18 Chd Biswajit


Client Suntony Signage File Final Gantry Truss-30m Date/Time
Span.std 07-Dec-2018 20:06

Design Of Member No. 109 As Per IS:800

Input Parameters

Member Section PIP603L

2
Cross Sectional Area Ax (mm ) 523.00
Net section factor 1.00
2
Net Effective Sectional Area Anet (mm ) 523.00
rz (mm) 20.32
ry (mm) 20.32
Unsupported Length - Major Axis For Slenderness Check Lz (mm) 1802.77
Unsupported Length - Minor Axis For Slenderness Check Ly (mm) 1802.77
Yield Stress fy (MPa) 240.00
Allowable Ratio For Interaction Check 1.00

Design Forces

Axial Load Fx (N ) -3817.34


Critical Loadcase No. 3

Details Of Calculation

Slenderness Checking

Lez (mm) 1802.77


Ley (mm) 1802.77
Lez / rz 88.71
Ley / ry 88.71
Actual Slenderness Ratio 88.71
Allowable Slenderness Ratio 400.00
Status SAFE

Check Against Axial Tension For Truss Member

Actual Tensile Stress ft (MPa)


=Fx / Anet 7.30

Print Time/Date: 07/12/2018 20:09 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 236 of 617
Job No Sheet No Rev
BN/SS/-01 237
Part
Software licensed to BN
Job Title Design of Overhead Gantry Hoarding Truss - 30m Span Ref

By Biswajit Date06-Dec-18 Chd Biswajit


Client Suntony Signage File Final Gantry Truss-30m Date/Time
Span.std 07-Dec-2018 20:06

Allowable Tensile Stress ft_allowable (MPa)


=0.60fy 144.00
Interaction ratio
=ft / ft_allowable 0.05
Status SAFE

Print Time/Date: 07/12/2018 20:09 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 237 of 617
Job No Sheet No Rev
BN/SS/-01 238
Part
Software licensed to BN
Job Title Design of Overhead Gantry Hoarding Truss - 30m Span Ref

By Biswajit Date06-Dec-18 Chd Biswajit


Client Suntony Signage File Final Gantry Truss-30m Date/Time
Span.std 07-Dec-2018 20:06

Design Of Member No. 110 As Per IS:800

Input Parameters

Member Section PIP424L

2
Cross Sectional Area Ax (mm ) 325.00
rz (mm) 14.10
ry (mm) 14.10
Unsupported Length - Major Axis For Slenderness Check Lz (mm) 1000.00
Unsupported Length - Minor Axis For Slenderness Check Ly (mm) 1000.00
Yield Stress fy (MPa) 240.00
Allowable Ratio For Interaction Check 1.00

Design Forces

Axial Load Fx (N ) 298.62


Critical Loadcase No. 3

Details Of Calculation

Slenderness Checking

Lez (mm) 1000.00


Ley (mm) 1000.00
Lez / rz 70.93
Ley / ry 70.93
Actual Slenderness Ratio 70.93
Allowable Slenderness Ratio 180.00
Status SAFE

Check Against Axial Compression For Truss Member

Actual Compressive Stress fc (MPa)


=Fx / Ax 0.92

Calculation Of Allowable Compressive Stress :

Print Time/Date: 07/12/2018 20:09 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 238 of 617
Job No Sheet No Rev
BN/SS/-01 239
Part
Software licensed to BN
Job Title Design of Overhead Gantry Hoarding Truss - 30m Span Ref

By Biswajit Date06-Dec-18 Chd Biswajit


Client Suntony Signage File Final Gantry Truss-30m Date/Time
Span.std 07-Dec-2018 20:06

E (MPa) 200000.00
L/r 70.93
fcc (MPa)
2 2
=π E / λ 392.36
Allowable Compressive Stress fc_allowable (MPa)
1.4 1.4
=0.6fccfy / [(fcc) + (fy) ] 107.66
Interaction ratio
=fc / fc_allowable 0.01
Status SAFE

Print Time/Date: 07/12/2018 20:09 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 239 of 617
Job No Sheet No Rev
BN/SS/-01 240
Part
Software licensed to BN
Job Title Design of Overhead Gantry Hoarding Truss - 30m Span Ref

By Biswajit Date06-Dec-18 Chd Biswajit


Client Suntony Signage File Final Gantry Truss-30m Date/Time
Span.std 07-Dec-2018 20:06

Design Of Member No. 111 As Per IS:800

Input Parameters

Member Section PIP483L

2
Cross Sectional Area Ax (mm ) 414.00
rz (mm) 16.08
ry (mm) 16.08
Unsupported Length - Major Axis For Slenderness Check Lz (mm) 2000.00
Unsupported Length - Minor Axis For Slenderness Check Ly (mm) 2000.00
Yield Stress fy (MPa) 240.00
Allowable Ratio For Interaction Check 1.00

Design Forces

Axial Load Fx (N ) 907.11


Critical Loadcase No. 3

Details Of Calculation

Slenderness Checking

Lez (mm) 2000.00


Ley (mm) 2000.00
Lez / rz 124.40
Ley / ry 124.40
Actual Slenderness Ratio 124.40
Allowable Slenderness Ratio 180.00
Status SAFE

Check Against Axial Compression For Truss Member

Actual Compressive Stress fc (MPa)


=Fx / Ax 2.19

Calculation Of Allowable Compressive Stress :

Print Time/Date: 07/12/2018 20:09 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 240 of 617
Job No Sheet No Rev
BN/SS/-01 241
Part
Software licensed to BN
Job Title Design of Overhead Gantry Hoarding Truss - 30m Span Ref

By Biswajit Date06-Dec-18 Chd Biswajit


Client Suntony Signage File Final Gantry Truss-30m Date/Time
Span.std 07-Dec-2018 20:06

E (MPa) 200000.00
L/r 124.40
fcc (MPa)
2 2
=π E / λ 127.54
Allowable Compressive Stress fc_allowable (MPa)
1.4 1.4
=0.6fccfy / [(fcc) + (fy) ] 59.79
Interaction ratio
=fc / fc_allowable 0.04
Status SAFE

Print Time/Date: 07/12/2018 20:09 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 241 of 617
Job No Sheet No Rev
BN/SS/-01 242
Part
Software licensed to BN
Job Title Design of Overhead Gantry Hoarding Truss - 30m Span Ref

By Biswajit Date06-Dec-18 Chd Biswajit


Client Suntony Signage File Final Gantry Truss-30m Date/Time
Span.std 07-Dec-2018 20:06

Design Of Member No. 112 As Per IS:800

Input Parameters

Member Section PIP483L

2
Cross Sectional Area Ax (mm ) 414.00
Net section factor 1.00
2
Net Effective Sectional Area Anet (mm ) 414.00
rz (mm) 16.08
ry (mm) 16.08
Unsupported Length - Major Axis For Slenderness Check Lz (mm) 2000.00
Unsupported Length - Minor Axis For Slenderness Check Ly (mm) 2000.00
Yield Stress fy (MPa) 240.00
Allowable Ratio For Interaction Check 1.00

Design Forces

Axial Load Fx (N ) -3736.64


Critical Loadcase No. 3

Details Of Calculation

Slenderness Checking

Lez (mm) 2000.00


Ley (mm) 2000.00
Lez / rz 124.40
Ley / ry 124.40
Actual Slenderness Ratio 124.40
Allowable Slenderness Ratio 400.00
Status SAFE

Check Against Axial Tension For Truss Member

Actual Tensile Stress ft (MPa)


=Fx / Anet 9.03

Print Time/Date: 07/12/2018 20:09 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 242 of 617
Job No Sheet No Rev
BN/SS/-01 243
Part
Software licensed to BN
Job Title Design of Overhead Gantry Hoarding Truss - 30m Span Ref

By Biswajit Date06-Dec-18 Chd Biswajit


Client Suntony Signage File Final Gantry Truss-30m Date/Time
Span.std 07-Dec-2018 20:06

Allowable Tensile Stress ft_allowable (MPa)


=0.60fy 144.00
Interaction ratio
=ft / ft_allowable 0.06
Status SAFE

Print Time/Date: 07/12/2018 20:09 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 243 of 617
Job No Sheet No Rev
BN/SS/-01 244
Part
Software licensed to BN
Job Title Design of Overhead Gantry Hoarding Truss - 30m Span Ref

By Biswajit Date06-Dec-18 Chd Biswajit


Client Suntony Signage File Final Gantry Truss-30m Date/Time
Span.std 07-Dec-2018 20:06

Design Of Member No. 113 As Per IS:800

Input Parameters

Member Section PIP424L

2
Cross Sectional Area Ax (mm ) 0.00
rz (mm) 14.10
ry (mm) 14.10
Unsupported Length - Major Axis For Slenderness Check Lz (mm) 1000.00
Unsupported Length - Minor Axis For Slenderness Check Ly (mm) 1000.00
Yield Stress fy (MPa) 0.00
Allowable Ratio For Interaction Check 1.00

Design Forces

Axial Load Fx (N ) 0.00


Critical Loadcase No. 0

Details Of Calculation

Slenderness Checking

Lez (mm) 1000.00


Ley (mm) 1000.00
Lez / rz 70.93
Ley / ry 70.93
Actual Slenderness Ratio 70.93
Allowable Slenderness Ratio 400.00
Status SAFE

Check Against Axial Compression For Truss Member

Actual Compressive Stress fc (MPa)


=Fx / Ax 0.00

Calculation Of Allowable Compressive Stress :

Print Time/Date: 07/12/2018 20:09 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 244 of 617
Job No Sheet No Rev
BN/SS/-01 245
Part
Software licensed to BN
Job Title Design of Overhead Gantry Hoarding Truss - 30m Span Ref

By Biswajit Date06-Dec-18 Chd Biswajit


Client Suntony Signage File Final Gantry Truss-30m Date/Time
Span.std 07-Dec-2018 20:06

E (MPa) 200000.00
L/r 70.93
fcc (MPa)
2 2
=π E / λ 392.36
Allowable Compressive Stress fc_allowable (MPa)
1.4 1.4
=0.6fccfy / [(fcc) + (fy) ] 0.00
Interaction ratio
=fc / fc_allowable 0.00
Status SAFE

Print Time/Date: 07/12/2018 20:09 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 245 of 617
Job No Sheet No Rev
BN/SS/-01 246
Part
Software licensed to BN
Job Title Design of Overhead Gantry Hoarding Truss - 30m Span Ref

By Biswajit Date06-Dec-18 Chd Biswajit


Client Suntony Signage File Final Gantry Truss-30m Date/Time
Span.std 07-Dec-2018 20:06

Design Of Member No. 114 As Per IS:800

Input Parameters

Member Section PIP603L

2
Cross Sectional Area Ax (mm ) 523.00
rz (mm) 20.32
ry (mm) 20.32
Unsupported Length - Major Axis For Slenderness Check Lz (mm) 1802.77
Unsupported Length - Minor Axis For Slenderness Check Ly (mm) 1802.77
Yield Stress fy (MPa) 240.00
Allowable Ratio For Interaction Check 1.00

Design Forces

Axial Load Fx (N ) 9889.74


Critical Loadcase No. 3

Details Of Calculation

Slenderness Checking

Lez (mm) 1802.77


Ley (mm) 1802.77
Lez / rz 88.71
Ley / ry 88.71
Actual Slenderness Ratio 88.71
Allowable Slenderness Ratio 180.00
Status SAFE

Check Against Axial Compression For Truss Member

Actual Compressive Stress fc (MPa)


=Fx / Ax 18.91

Calculation Of Allowable Compressive Stress :

Print Time/Date: 07/12/2018 20:09 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 246 of 617
Job No Sheet No Rev
BN/SS/-01 247
Part
Software licensed to BN
Job Title Design of Overhead Gantry Hoarding Truss - 30m Span Ref

By Biswajit Date06-Dec-18 Chd Biswajit


Client Suntony Signage File Final Gantry Truss-30m Date/Time
Span.std 07-Dec-2018 20:06

E (MPa) 200000.00
L/r 88.71
fcc (MPa)
2 2
=π E / λ 250.84
Allowable Compressive Stress fc_allowable (MPa)
1.4 1.4
=0.6fccfy / [(fcc) + (fy) ] 89.69
Interaction ratio
=fc / fc_allowable 0.21
Status SAFE

Print Time/Date: 07/12/2018 20:09 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 247 of 617
Job No Sheet No Rev
BN/SS/-01 248
Part
Software licensed to BN
Job Title Design of Overhead Gantry Hoarding Truss - 30m Span Ref

By Biswajit Date06-Dec-18 Chd Biswajit


Client Suntony Signage File Final Gantry Truss-30m Date/Time
Span.std 07-Dec-2018 20:06

Design Of Member No. 115 As Per IS:800

Input Parameters

Member Section PIP483L

2
Cross Sectional Area Ax (mm ) 414.00
Net section factor 1.00
2
Net Effective Sectional Area Anet (mm ) 414.00
rz (mm) 16.08
ry (mm) 16.08
Unsupported Length - Major Axis For Slenderness Check Lz (mm) 2500.00
Unsupported Length - Minor Axis For Slenderness Check Ly (mm) 2500.00
Yield Stress fy (MPa) 240.00
Allowable Ratio For Interaction Check 1.00

Design Forces

Axial Load Fx (N ) -847.36


Critical Loadcase No. 3

Details Of Calculation

Slenderness Checking

Lez (mm) 2500.00


Ley (mm) 2500.00
Lez / rz 155.51
Ley / ry 155.51
Actual Slenderness Ratio 155.51
Allowable Slenderness Ratio 400.00
Status SAFE

Check Against Axial Tension For Truss Member

Actual Tensile Stress ft (MPa)


=Fx / Anet 2.05

Print Time/Date: 07/12/2018 20:09 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 248 of 617
Job No Sheet No Rev
BN/SS/-01 249
Part
Software licensed to BN
Job Title Design of Overhead Gantry Hoarding Truss - 30m Span Ref

By Biswajit Date06-Dec-18 Chd Biswajit


Client Suntony Signage File Final Gantry Truss-30m Date/Time
Span.std 07-Dec-2018 20:06

Allowable Tensile Stress ft_allowable (MPa)


=0.60fy 144.00
Interaction ratio
=ft / ft_allowable 0.01
Status SAFE

Print Time/Date: 07/12/2018 20:09 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 249 of 617
Job No Sheet No Rev
BN/SS/-01 250
Part
Software licensed to BN
Job Title Design of Overhead Gantry Hoarding Truss - 30m Span Ref

By Biswajit Date06-Dec-18 Chd Biswajit


Client Suntony Signage File Final Gantry Truss-30m Date/Time
Span.std 07-Dec-2018 20:06

Design Of Member No. 116 As Per IS:800

Input Parameters

Member Section PIP483L

2
Cross Sectional Area Ax (mm ) 414.00
rz (mm) 16.08
ry (mm) 16.08
Unsupported Length - Major Axis For Slenderness Check Lz (mm) 2500.00
Unsupported Length - Minor Axis For Slenderness Check Ly (mm) 2500.00
Yield Stress fy (MPa) 240.00
Allowable Ratio For Interaction Check 1.00

Design Forces

Axial Load Fx (N ) 5828.90


Critical Loadcase No. 3

Details Of Calculation

Slenderness Checking

Lez (mm) 2500.00


Ley (mm) 2500.00
Lez / rz 155.51
Ley / ry 155.51
Actual Slenderness Ratio 155.51
Allowable Slenderness Ratio 180.00
Status SAFE

Check Against Axial Compression For Truss Member

Actual Compressive Stress fc (MPa)


=Fx / Ax 14.08

Calculation Of Allowable Compressive Stress :

Print Time/Date: 07/12/2018 20:09 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 250 of 617
Job No Sheet No Rev
BN/SS/-01 251
Part
Software licensed to BN
Job Title Design of Overhead Gantry Hoarding Truss - 30m Span Ref

By Biswajit Date06-Dec-18 Chd Biswajit


Client Suntony Signage File Final Gantry Truss-30m Date/Time
Span.std 07-Dec-2018 20:06

E (MPa) 200000.00
L/r 155.51
fcc (MPa)
2 2
=π E / λ 81.63
Allowable Compressive Stress fc_allowable (MPa)
1.4 1.4
=0.6fccfy / [(fcc) + (fy) ] 42.47
Interaction ratio
=fc / fc_allowable 0.33
Status SAFE

Print Time/Date: 07/12/2018 20:09 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 251 of 617
Job No Sheet No Rev
BN/SS/-01 252
Part
Software licensed to BN
Job Title Design of Overhead Gantry Hoarding Truss - 30m Span Ref

By Biswajit Date06-Dec-18 Chd Biswajit


Client Suntony Signage File Final Gantry Truss-30m Date/Time
Span.std 07-Dec-2018 20:06

Design Of Member No. 117 As Per IS:800

Input Parameters

Member Section PIP603L

2
Cross Sectional Area Ax (mm ) 523.00
rz (mm) 20.32
ry (mm) 20.32
Unsupported Length - Major Axis For Slenderness Check Lz (mm) 1802.77
Unsupported Length - Minor Axis For Slenderness Check Ly (mm) 1802.77
Yield Stress fy (MPa) 240.00
Allowable Ratio For Interaction Check 1.00

Design Forces

Axial Load Fx (N ) 7216.69


Critical Loadcase No. 3

Details Of Calculation

Slenderness Checking

Lez (mm) 1802.77


Ley (mm) 1802.77
Lez / rz 88.71
Ley / ry 88.71
Actual Slenderness Ratio 88.71
Allowable Slenderness Ratio 180.00
Status SAFE

Check Against Axial Compression For Truss Member

Actual Compressive Stress fc (MPa)


=Fx / Ax 13.80

Calculation Of Allowable Compressive Stress :

Print Time/Date: 07/12/2018 20:09 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 252 of 617
Job No Sheet No Rev
BN/SS/-01 253
Part
Software licensed to BN
Job Title Design of Overhead Gantry Hoarding Truss - 30m Span Ref

By Biswajit Date06-Dec-18 Chd Biswajit


Client Suntony Signage File Final Gantry Truss-30m Date/Time
Span.std 07-Dec-2018 20:06

E (MPa) 200000.00
L/r 88.71
fcc (MPa)
2 2
=π E / λ 250.84
Allowable Compressive Stress fc_allowable (MPa)
1.4 1.4
=0.6fccfy / [(fcc) + (fy) ] 89.69
Interaction ratio
=fc / fc_allowable 0.15
Status SAFE

Print Time/Date: 07/12/2018 20:09 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 253 of 617
Job No Sheet No Rev
BN/SS/-01 254
Part
Software licensed to BN
Job Title Design of Overhead Gantry Hoarding Truss - 30m Span Ref

By Biswajit Date06-Dec-18 Chd Biswajit


Client Suntony Signage File Final Gantry Truss-30m Date/Time
Span.std 07-Dec-2018 20:06

Design Of Member No. 118 As Per IS:800

Input Parameters

Member Section PIP424L

2
Cross Sectional Area Ax (mm ) 325.00
rz (mm) 14.10
ry (mm) 14.10
Unsupported Length - Major Axis For Slenderness Check Lz (mm) 1000.00
Unsupported Length - Minor Axis For Slenderness Check Ly (mm) 1000.00
Yield Stress fy (MPa) 240.00
Allowable Ratio For Interaction Check 1.00

Design Forces

Axial Load Fx (N ) 1587.00


Critical Loadcase No. 3

Details Of Calculation

Slenderness Checking

Lez (mm) 1000.00


Ley (mm) 1000.00
Lez / rz 70.93
Ley / ry 70.93
Actual Slenderness Ratio 70.93
Allowable Slenderness Ratio 180.00
Status SAFE

Check Against Axial Compression For Truss Member

Actual Compressive Stress fc (MPa)


=Fx / Ax 4.88

Calculation Of Allowable Compressive Stress :

Print Time/Date: 07/12/2018 20:09 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 254 of 617
Job No Sheet No Rev
BN/SS/-01 255
Part
Software licensed to BN
Job Title Design of Overhead Gantry Hoarding Truss - 30m Span Ref

By Biswajit Date06-Dec-18 Chd Biswajit


Client Suntony Signage File Final Gantry Truss-30m Date/Time
Span.std 07-Dec-2018 20:06

E (MPa) 200000.00
L/r 70.93
fcc (MPa)
2 2
=π E / λ 392.36
Allowable Compressive Stress fc_allowable (MPa)
1.4 1.4
=0.6fccfy / [(fcc) + (fy) ] 107.66
Interaction ratio
=fc / fc_allowable 0.05
Status SAFE

Print Time/Date: 07/12/2018 20:09 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 255 of 617
Job No Sheet No Rev
BN/SS/-01 256
Part
Software licensed to BN
Job Title Design of Overhead Gantry Hoarding Truss - 30m Span Ref

By Biswajit Date06-Dec-18 Chd Biswajit


Client Suntony Signage File Final Gantry Truss-30m Date/Time
Span.std 07-Dec-2018 20:06

Design Of Member No. 119 As Per IS:800

Input Parameters

Member Section PIP483L

2
Cross Sectional Area Ax (mm ) 414.00
Net section factor 1.00
2
Net Effective Sectional Area Anet (mm ) 414.00
rz (mm) 16.08
ry (mm) 16.08
Unsupported Length - Major Axis For Slenderness Check Lz (mm) 2000.00
Unsupported Length - Minor Axis For Slenderness Check Ly (mm) 2000.00
Yield Stress fy (MPa) 240.00
Allowable Ratio For Interaction Check 1.00

Design Forces

Axial Load Fx (N ) -430.43


Critical Loadcase No. 3

Details Of Calculation

Slenderness Checking

Lez (mm) 2000.00


Ley (mm) 2000.00
Lez / rz 124.40
Ley / ry 124.40
Actual Slenderness Ratio 124.40
Allowable Slenderness Ratio 400.00
Status SAFE

Check Against Axial Tension For Truss Member

Actual Tensile Stress ft (MPa)


=Fx / Anet 1.04

Print Time/Date: 07/12/2018 20:09 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 256 of 617
Job No Sheet No Rev
BN/SS/-01 257
Part
Software licensed to BN
Job Title Design of Overhead Gantry Hoarding Truss - 30m Span Ref

By Biswajit Date06-Dec-18 Chd Biswajit


Client Suntony Signage File Final Gantry Truss-30m Date/Time
Span.std 07-Dec-2018 20:06

Allowable Tensile Stress ft_allowable (MPa)


=0.60fy 144.00
Interaction ratio
=ft / ft_allowable 0.01
Status SAFE

Print Time/Date: 07/12/2018 20:09 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 257 of 617
Job No Sheet No Rev
BN/SS/-01 258
Part
Software licensed to BN
Job Title Design of Overhead Gantry Hoarding Truss - 30m Span Ref

By Biswajit Date06-Dec-18 Chd Biswajit


Client Suntony Signage File Final Gantry Truss-30m Date/Time
Span.std 07-Dec-2018 20:06

Design Of Member No. 120 As Per IS:800

Input Parameters

Member Section PIP483L

2
Cross Sectional Area Ax (mm ) 414.00
Net section factor 1.00
2
Net Effective Sectional Area Anet (mm ) 414.00
rz (mm) 16.08
ry (mm) 16.08
Unsupported Length - Major Axis For Slenderness Check Lz (mm) 2000.00
Unsupported Length - Minor Axis For Slenderness Check Ly (mm) 2000.00
Yield Stress fy (MPa) 240.00
Allowable Ratio For Interaction Check 1.00

Design Forces

Axial Load Fx (N ) -4892.34


Critical Loadcase No. 3

Details Of Calculation

Slenderness Checking

Lez (mm) 2000.00


Ley (mm) 2000.00
Lez / rz 124.40
Ley / ry 124.40
Actual Slenderness Ratio 124.40
Allowable Slenderness Ratio 400.00
Status SAFE

Check Against Axial Tension For Truss Member

Actual Tensile Stress ft (MPa)


=Fx / Anet 11.82

Print Time/Date: 07/12/2018 20:09 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 258 of 617
Job No Sheet No Rev
BN/SS/-01 259
Part
Software licensed to BN
Job Title Design of Overhead Gantry Hoarding Truss - 30m Span Ref

By Biswajit Date06-Dec-18 Chd Biswajit


Client Suntony Signage File Final Gantry Truss-30m Date/Time
Span.std 07-Dec-2018 20:06

Allowable Tensile Stress ft_allowable (MPa)


=0.60fy 144.00
Interaction ratio
=ft / ft_allowable 0.08
Status SAFE

Print Time/Date: 07/12/2018 20:09 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 259 of 617
Job No Sheet No Rev
BN/SS/-01 260
Part
Software licensed to BN
Job Title Design of Overhead Gantry Hoarding Truss - 30m Span Ref

By Biswajit Date06-Dec-18 Chd Biswajit


Client Suntony Signage File Final Gantry Truss-30m Date/Time
Span.std 07-Dec-2018 20:06

Design Of Member No. 121 As Per IS:800

Input Parameters

Member Section PIP424L

2
Cross Sectional Area Ax (mm ) 325.00
rz (mm) 14.10
ry (mm) 14.10
Unsupported Length - Major Axis For Slenderness Check Lz (mm) 1000.00
Unsupported Length - Minor Axis For Slenderness Check Ly (mm) 1000.00
Yield Stress fy (MPa) 240.00
Allowable Ratio For Interaction Check 1.00

Design Forces

Axial Load Fx (N ) 1230.86


Critical Loadcase No. 3

Details Of Calculation

Slenderness Checking

Lez (mm) 1000.00


Ley (mm) 1000.00
Lez / rz 70.93
Ley / ry 70.93
Actual Slenderness Ratio 70.93
Allowable Slenderness Ratio 180.00
Status SAFE

Check Against Axial Compression For Truss Member

Actual Compressive Stress fc (MPa)


=Fx / Ax 3.79

Calculation Of Allowable Compressive Stress :

Print Time/Date: 07/12/2018 20:09 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 260 of 617
Job No Sheet No Rev
BN/SS/-01 261
Part
Software licensed to BN
Job Title Design of Overhead Gantry Hoarding Truss - 30m Span Ref

By Biswajit Date06-Dec-18 Chd Biswajit


Client Suntony Signage File Final Gantry Truss-30m Date/Time
Span.std 07-Dec-2018 20:06

E (MPa) 200000.00
L/r 70.93
fcc (MPa)
2 2
=π E / λ 392.36
Allowable Compressive Stress fc_allowable (MPa)
1.4 1.4
=0.6fccfy / [(fcc) + (fy) ] 107.66
Interaction ratio
=fc / fc_allowable 0.04
Status SAFE

Print Time/Date: 07/12/2018 20:09 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 261 of 617
Job No Sheet No Rev
BN/SS/-01 262
Part
Software licensed to BN
Job Title Design of Overhead Gantry Hoarding Truss - 30m Span Ref

By Biswajit Date06-Dec-18 Chd Biswajit


Client Suntony Signage File Final Gantry Truss-30m Date/Time
Span.std 07-Dec-2018 20:06

Design Of Member No. 122 As Per IS:800

Input Parameters

Member Section PIP603L

2
Cross Sectional Area Ax (mm ) 523.00
Net section factor 1.00
2
Net Effective Sectional Area Anet (mm ) 523.00
rz (mm) 20.32
ry (mm) 20.32
Unsupported Length - Major Axis For Slenderness Check Lz (mm) 1802.77
Unsupported Length - Minor Axis For Slenderness Check Ly (mm) 1802.77
Yield Stress fy (MPa) 240.00
Allowable Ratio For Interaction Check 1.00

Design Forces

Axial Load Fx (N ) -13392.78


Critical Loadcase No. 3

Details Of Calculation

Slenderness Checking

Lez (mm) 1802.77


Ley (mm) 1802.77
Lez / rz 88.71
Ley / ry 88.71
Actual Slenderness Ratio 88.71
Allowable Slenderness Ratio 400.00
Status SAFE

Check Against Axial Tension For Truss Member

Actual Tensile Stress ft (MPa)


=Fx / Anet 25.61

Print Time/Date: 07/12/2018 20:09 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 262 of 617
Job No Sheet No Rev
BN/SS/-01 263
Part
Software licensed to BN
Job Title Design of Overhead Gantry Hoarding Truss - 30m Span Ref

By Biswajit Date06-Dec-18 Chd Biswajit


Client Suntony Signage File Final Gantry Truss-30m Date/Time
Span.std 07-Dec-2018 20:06

Allowable Tensile Stress ft_allowable (MPa)


=0.60fy 144.00
Interaction ratio
=ft / ft_allowable 0.18
Status SAFE

Print Time/Date: 07/12/2018 20:09 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 263 of 617
Job No Sheet No Rev
BN/SS/-01 264
Part
Software licensed to BN
Job Title Design of Overhead Gantry Hoarding Truss - 30m Span Ref

By Biswajit Date06-Dec-18 Chd Biswajit


Client Suntony Signage File Final Gantry Truss-30m Date/Time
Span.std 07-Dec-2018 20:06

Design Of Member No. 123 As Per IS:800

Input Parameters

Member Section PIP483L

2
Cross Sectional Area Ax (mm ) 414.00
rz (mm) 16.08
ry (mm) 16.08
Unsupported Length - Major Axis For Slenderness Check Lz (mm) 2500.00
Unsupported Length - Minor Axis For Slenderness Check Ly (mm) 2500.00
Yield Stress fy (MPa) 240.00
Allowable Ratio For Interaction Check 1.00

Design Forces

Axial Load Fx (N ) 902.93


Critical Loadcase No. 3

Details Of Calculation

Slenderness Checking

Lez (mm) 2500.00


Ley (mm) 2500.00
Lez / rz 155.51
Ley / ry 155.51
Actual Slenderness Ratio 155.51
Allowable Slenderness Ratio 180.00
Status SAFE

Check Against Axial Compression For Truss Member

Actual Compressive Stress fc (MPa)


=Fx / Ax 2.18

Calculation Of Allowable Compressive Stress :

Print Time/Date: 07/12/2018 20:09 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 264 of 617
Job No Sheet No Rev
BN/SS/-01 265
Part
Software licensed to BN
Job Title Design of Overhead Gantry Hoarding Truss - 30m Span Ref

By Biswajit Date06-Dec-18 Chd Biswajit


Client Suntony Signage File Final Gantry Truss-30m Date/Time
Span.std 07-Dec-2018 20:06

E (MPa) 200000.00
L/r 155.51
fcc (MPa)
2 2
=π E / λ 81.63
Allowable Compressive Stress fc_allowable (MPa)
1.4 1.4
=0.6fccfy / [(fcc) + (fy) ] 42.47
Interaction ratio
=fc / fc_allowable 0.05
Status SAFE

Print Time/Date: 07/12/2018 20:09 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 265 of 617
Job No Sheet No Rev
BN/SS/-01 266
Part
Software licensed to BN
Job Title Design of Overhead Gantry Hoarding Truss - 30m Span Ref

By Biswajit Date06-Dec-18 Chd Biswajit


Client Suntony Signage File Final Gantry Truss-30m Date/Time
Span.std 07-Dec-2018 20:06

Design Of Member No. 124 As Per IS:800

Input Parameters

Member Section PIP483L

2
Cross Sectional Area Ax (mm ) 414.00
rz (mm) 16.08
ry (mm) 16.08
Unsupported Length - Major Axis For Slenderness Check Lz (mm) 2500.00
Unsupported Length - Minor Axis For Slenderness Check Ly (mm) 2500.00
Yield Stress fy (MPa) 240.00
Allowable Ratio For Interaction Check 1.00

Design Forces

Axial Load Fx (N ) 5541.58


Critical Loadcase No. 3

Details Of Calculation

Slenderness Checking

Lez (mm) 2500.00


Ley (mm) 2500.00
Lez / rz 155.51
Ley / ry 155.51
Actual Slenderness Ratio 155.51
Allowable Slenderness Ratio 180.00
Status SAFE

Check Against Axial Compression For Truss Member

Actual Compressive Stress fc (MPa)


=Fx / Ax 13.39

Calculation Of Allowable Compressive Stress :

Print Time/Date: 07/12/2018 20:09 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 266 of 617
Job No Sheet No Rev
BN/SS/-01 267
Part
Software licensed to BN
Job Title Design of Overhead Gantry Hoarding Truss - 30m Span Ref

By Biswajit Date06-Dec-18 Chd Biswajit


Client Suntony Signage File Final Gantry Truss-30m Date/Time
Span.std 07-Dec-2018 20:06

E (MPa) 200000.00
L/r 155.51
fcc (MPa)
2 2
=π E / λ 81.63
Allowable Compressive Stress fc_allowable (MPa)
1.4 1.4
=0.6fccfy / [(fcc) + (fy) ] 42.47
Interaction ratio
=fc / fc_allowable 0.32
Status SAFE

Print Time/Date: 07/12/2018 20:09 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 267 of 617
Job No Sheet No Rev
BN/SS/-01 268
Part
Software licensed to BN
Job Title Design of Overhead Gantry Hoarding Truss - 30m Span Ref

By Biswajit Date06-Dec-18 Chd Biswajit


Client Suntony Signage File Final Gantry Truss-30m Date/Time
Span.std 07-Dec-2018 20:06

Design Of Member No. 125 As Per IS:800

Input Parameters

Member Section PIP603L

2
Cross Sectional Area Ax (mm ) 523.00
Net section factor 1.00
2
Net Effective Sectional Area Anet (mm ) 523.00
rz (mm) 20.32
ry (mm) 20.32
Unsupported Length - Major Axis For Slenderness Check Lz (mm) 1802.77
Unsupported Length - Minor Axis For Slenderness Check Ly (mm) 1802.77
Yield Stress fy (MPa) 240.00
Allowable Ratio For Interaction Check 1.00

Design Forces

Axial Load Fx (N ) -9435.65


Critical Loadcase No. 3

Details Of Calculation

Slenderness Checking

Lez (mm) 1802.77


Ley (mm) 1802.77
Lez / rz 88.71
Ley / ry 88.71
Actual Slenderness Ratio 88.71
Allowable Slenderness Ratio 400.00
Status SAFE

Check Against Axial Tension For Truss Member

Actual Tensile Stress ft (MPa)


=Fx / Anet 18.04

Print Time/Date: 07/12/2018 20:09 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 268 of 617
Job No Sheet No Rev
BN/SS/-01 269
Part
Software licensed to BN
Job Title Design of Overhead Gantry Hoarding Truss - 30m Span Ref

By Biswajit Date06-Dec-18 Chd Biswajit


Client Suntony Signage File Final Gantry Truss-30m Date/Time
Span.std 07-Dec-2018 20:06

Allowable Tensile Stress ft_allowable (MPa)


=0.60fy 144.00
Interaction ratio
=ft / ft_allowable 0.13
Status SAFE

Print Time/Date: 07/12/2018 20:09 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 269 of 617
Job No Sheet No Rev
BN/SS/-01 270
Part
Software licensed to BN
Job Title Design of Overhead Gantry Hoarding Truss - 30m Span Ref

By Biswajit Date06-Dec-18 Chd Biswajit


Client Suntony Signage File Final Gantry Truss-30m Date/Time
Span.std 07-Dec-2018 20:06

Design Of Member No. 126 As Per IS:800

Input Parameters

Member Section PIP424L

2
Cross Sectional Area Ax (mm ) 325.00
rz (mm) 14.10
ry (mm) 14.10
Unsupported Length - Major Axis For Slenderness Check Lz (mm) 1000.00
Unsupported Length - Minor Axis For Slenderness Check Ly (mm) 1000.00
Yield Stress fy (MPa) 240.00
Allowable Ratio For Interaction Check 1.00

Design Forces

Axial Load Fx (N ) 106.20


Critical Loadcase No. 3

Details Of Calculation

Slenderness Checking

Lez (mm) 1000.00


Ley (mm) 1000.00
Lez / rz 70.93
Ley / ry 70.93
Actual Slenderness Ratio 70.93
Allowable Slenderness Ratio 180.00
Status SAFE

Check Against Axial Compression For Truss Member

Actual Compressive Stress fc (MPa)


=Fx / Ax 0.33

Calculation Of Allowable Compressive Stress :

Print Time/Date: 07/12/2018 20:09 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 270 of 617
Job No Sheet No Rev
BN/SS/-01 271
Part
Software licensed to BN
Job Title Design of Overhead Gantry Hoarding Truss - 30m Span Ref

By Biswajit Date06-Dec-18 Chd Biswajit


Client Suntony Signage File Final Gantry Truss-30m Date/Time
Span.std 07-Dec-2018 20:06

E (MPa) 200000.00
L/r 70.93
fcc (MPa)
2 2
=π E / λ 392.36
Allowable Compressive Stress fc_allowable (MPa)
1.4 1.4
=0.6fccfy / [(fcc) + (fy) ] 107.66
Interaction ratio
=fc / fc_allowable 0.00
Status SAFE

Print Time/Date: 07/12/2018 20:09 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 271 of 617
Job No Sheet No Rev
BN/SS/-01 272
Part
Software licensed to BN
Job Title Design of Overhead Gantry Hoarding Truss - 30m Span Ref

By Biswajit Date06-Dec-18 Chd Biswajit


Client Suntony Signage File Final Gantry Truss-30m Date/Time
Span.std 07-Dec-2018 20:06

Design Of Member No. 127 As Per IS:800

Input Parameters

Member Section PIP483L

2
Cross Sectional Area Ax (mm ) 414.00
Net section factor 1.00
2
Net Effective Sectional Area Anet (mm ) 414.00
rz (mm) 16.08
ry (mm) 16.08
Unsupported Length - Major Axis For Slenderness Check Lz (mm) 2000.00
Unsupported Length - Minor Axis For Slenderness Check Ly (mm) 2000.00
Yield Stress fy (MPa) 240.00
Allowable Ratio For Interaction Check 1.00

Design Forces

Axial Load Fx (N ) -776.49


Critical Loadcase No. 3

Details Of Calculation

Slenderness Checking

Lez (mm) 2000.00


Ley (mm) 2000.00
Lez / rz 124.40
Ley / ry 124.40
Actual Slenderness Ratio 124.40
Allowable Slenderness Ratio 400.00
Status SAFE

Check Against Axial Tension For Truss Member

Actual Tensile Stress ft (MPa)


=Fx / Anet 1.88

Print Time/Date: 07/12/2018 20:09 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 272 of 617
Job No Sheet No Rev
BN/SS/-01 273
Part
Software licensed to BN
Job Title Design of Overhead Gantry Hoarding Truss - 30m Span Ref

By Biswajit Date06-Dec-18 Chd Biswajit


Client Suntony Signage File Final Gantry Truss-30m Date/Time
Span.std 07-Dec-2018 20:06

Allowable Tensile Stress ft_allowable (MPa)


=0.60fy 144.00
Interaction ratio
=ft / ft_allowable 0.01
Status SAFE

Print Time/Date: 07/12/2018 20:09 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 273 of 617
Job No Sheet No Rev
BN/SS/-01 274
Part
Software licensed to BN
Job Title Design of Overhead Gantry Hoarding Truss - 30m Span Ref

By Biswajit Date06-Dec-18 Chd Biswajit


Client Suntony Signage File Final Gantry Truss-30m Date/Time
Span.std 07-Dec-2018 20:06

Design Of Member No. 128 As Per IS:800

Input Parameters

Member Section PIP483L

2
Cross Sectional Area Ax (mm ) 414.00
Net section factor 1.00
2
Net Effective Sectional Area Anet (mm ) 414.00
rz (mm) 16.08
ry (mm) 16.08
Unsupported Length - Major Axis For Slenderness Check Lz (mm) 2000.00
Unsupported Length - Minor Axis For Slenderness Check Ly (mm) 2000.00
Yield Stress fy (MPa) 240.00
Allowable Ratio For Interaction Check 1.00

Design Forces

Axial Load Fx (N ) -4738.54


Critical Loadcase No. 3

Details Of Calculation

Slenderness Checking

Lez (mm) 2000.00


Ley (mm) 2000.00
Lez / rz 124.40
Ley / ry 124.40
Actual Slenderness Ratio 124.40
Allowable Slenderness Ratio 400.00
Status SAFE

Check Against Axial Tension For Truss Member

Actual Tensile Stress ft (MPa)


=Fx / Anet 11.45

Print Time/Date: 07/12/2018 20:09 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 274 of 617
Job No Sheet No Rev
BN/SS/-01 275
Part
Software licensed to BN
Job Title Design of Overhead Gantry Hoarding Truss - 30m Span Ref

By Biswajit Date06-Dec-18 Chd Biswajit


Client Suntony Signage File Final Gantry Truss-30m Date/Time
Span.std 07-Dec-2018 20:06

Allowable Tensile Stress ft_allowable (MPa)


=0.60fy 144.00
Interaction ratio
=ft / ft_allowable 0.08
Status SAFE

Print Time/Date: 07/12/2018 20:09 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 275 of 617
Job No Sheet No Rev
BN/SS/-01 276
Part
Software licensed to BN
Job Title Design of Overhead Gantry Hoarding Truss - 30m Span Ref

By Biswajit Date06-Dec-18 Chd Biswajit


Client Suntony Signage File Final Gantry Truss-30m Date/Time
Span.std 07-Dec-2018 20:06

Design Of Member No. 129 As Per IS:800

Input Parameters

Member Section PIP424L

2
Cross Sectional Area Ax (mm ) 0.00
rz (mm) 14.10
ry (mm) 14.10
Unsupported Length - Major Axis For Slenderness Check Lz (mm) 1000.00
Unsupported Length - Minor Axis For Slenderness Check Ly (mm) 1000.00
Yield Stress fy (MPa) 0.00
Allowable Ratio For Interaction Check 1.00

Design Forces

Axial Load Fx (N ) 0.00


Critical Loadcase No. 0

Details Of Calculation

Slenderness Checking

Lez (mm) 1000.00


Ley (mm) 1000.00
Lez / rz 70.93
Ley / ry 70.93
Actual Slenderness Ratio 70.93
Allowable Slenderness Ratio 400.00
Status SAFE

Check Against Axial Compression For Truss Member

Actual Compressive Stress fc (MPa)


=Fx / Ax 0.00

Calculation Of Allowable Compressive Stress :

Print Time/Date: 07/12/2018 20:09 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 276 of 617
Job No Sheet No Rev
BN/SS/-01 277
Part
Software licensed to BN
Job Title Design of Overhead Gantry Hoarding Truss - 30m Span Ref

By Biswajit Date06-Dec-18 Chd Biswajit


Client Suntony Signage File Final Gantry Truss-30m Date/Time
Span.std 07-Dec-2018 20:06

E (MPa) 200000.00
L/r 70.93
fcc (MPa)
2 2
=π E / λ 392.36
Allowable Compressive Stress fc_allowable (MPa)
1.4 1.4
=0.6fccfy / [(fcc) + (fy) ] 0.00
Interaction ratio
=fc / fc_allowable 0.00
Status SAFE

Print Time/Date: 07/12/2018 20:09 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 277 of 617
Job No Sheet No Rev
BN/SS/-01 278
Part
Software licensed to BN
Job Title Design of Overhead Gantry Hoarding Truss - 30m Span Ref

By Biswajit Date06-Dec-18 Chd Biswajit


Client Suntony Signage File Final Gantry Truss-30m Date/Time
Span.std 07-Dec-2018 20:06

Design Of Member No. 130 As Per IS:800

Input Parameters

Member Section PIP603L

2
Cross Sectional Area Ax (mm ) 523.00
rz (mm) 20.32
ry (mm) 20.32
Unsupported Length - Major Axis For Slenderness Check Lz (mm) 1802.77
Unsupported Length - Minor Axis For Slenderness Check Ly (mm) 1802.77
Yield Stress fy (MPa) 240.00
Allowable Ratio For Interaction Check 1.00

Design Forces

Axial Load Fx (N ) 16062.32


Critical Loadcase No. 3

Details Of Calculation

Slenderness Checking

Lez (mm) 1802.77


Ley (mm) 1802.77
Lez / rz 88.71
Ley / ry 88.71
Actual Slenderness Ratio 88.71
Allowable Slenderness Ratio 180.00
Status SAFE

Check Against Axial Compression For Truss Member

Actual Compressive Stress fc (MPa)


=Fx / Ax 30.71

Calculation Of Allowable Compressive Stress :

Print Time/Date: 07/12/2018 20:09 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 278 of 617
Job No Sheet No Rev
BN/SS/-01 279
Part
Software licensed to BN
Job Title Design of Overhead Gantry Hoarding Truss - 30m Span Ref

By Biswajit Date06-Dec-18 Chd Biswajit


Client Suntony Signage File Final Gantry Truss-30m Date/Time
Span.std 07-Dec-2018 20:06

E (MPa) 200000.00
L/r 88.71
fcc (MPa)
2 2
=π E / λ 250.84
Allowable Compressive Stress fc_allowable (MPa)
1.4 1.4
=0.6fccfy / [(fcc) + (fy) ] 89.69
Interaction ratio
=fc / fc_allowable 0.34
Status SAFE

Print Time/Date: 07/12/2018 20:09 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 279 of 617
Job No Sheet No Rev
BN/SS/-01 280
Part
Software licensed to BN
Job Title Design of Overhead Gantry Hoarding Truss - 30m Span Ref

By Biswajit Date06-Dec-18 Chd Biswajit


Client Suntony Signage File Final Gantry Truss-30m Date/Time
Span.std 07-Dec-2018 20:06

Design Of Member No. 131 As Per IS:800

Input Parameters

Member Section PIP483L

2
Cross Sectional Area Ax (mm ) 414.00
rz (mm) 16.08
ry (mm) 16.08
Unsupported Length - Major Axis For Slenderness Check Lz (mm) 2500.00
Unsupported Length - Minor Axis For Slenderness Check Ly (mm) 2500.00
Yield Stress fy (MPa) 240.00
Allowable Ratio For Interaction Check 1.00

Design Forces

Axial Load Fx (N ) 1240.44


Critical Loadcase No. 3

Details Of Calculation

Slenderness Checking

Lez (mm) 2500.00


Ley (mm) 2500.00
Lez / rz 155.51
Ley / ry 155.51
Actual Slenderness Ratio 155.51
Allowable Slenderness Ratio 180.00
Status SAFE

Check Against Axial Compression For Truss Member

Actual Compressive Stress fc (MPa)


=Fx / Ax 3.00

Calculation Of Allowable Compressive Stress :

Print Time/Date: 07/12/2018 20:09 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 280 of 617
Job No Sheet No Rev
BN/SS/-01 281
Part
Software licensed to BN
Job Title Design of Overhead Gantry Hoarding Truss - 30m Span Ref

By Biswajit Date06-Dec-18 Chd Biswajit


Client Suntony Signage File Final Gantry Truss-30m Date/Time
Span.std 07-Dec-2018 20:06

E (MPa) 200000.00
L/r 155.51
fcc (MPa)
2 2
=π E / λ 81.63
Allowable Compressive Stress fc_allowable (MPa)
1.4 1.4
=0.6fccfy / [(fcc) + (fy) ] 42.47
Interaction ratio
=fc / fc_allowable 0.07
Status SAFE

Print Time/Date: 07/12/2018 20:09 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 281 of 617
Job No Sheet No Rev
BN/SS/-01 282
Part
Software licensed to BN
Job Title Design of Overhead Gantry Hoarding Truss - 30m Span Ref

By Biswajit Date06-Dec-18 Chd Biswajit


Client Suntony Signage File Final Gantry Truss-30m Date/Time
Span.std 07-Dec-2018 20:06

Design Of Member No. 132 As Per IS:800

Input Parameters

Member Section PIP483L

2
Cross Sectional Area Ax (mm ) 414.00
rz (mm) 16.08
ry (mm) 16.08
Unsupported Length - Major Axis For Slenderness Check Lz (mm) 2500.00
Unsupported Length - Minor Axis For Slenderness Check Ly (mm) 2500.00
Yield Stress fy (MPa) 240.00
Allowable Ratio For Interaction Check 1.00

Design Forces

Axial Load Fx (N ) 6600.24


Critical Loadcase No. 3

Details Of Calculation

Slenderness Checking

Lez (mm) 2500.00


Ley (mm) 2500.00
Lez / rz 155.51
Ley / ry 155.51
Actual Slenderness Ratio 155.51
Allowable Slenderness Ratio 180.00
Status SAFE

Check Against Axial Compression For Truss Member

Actual Compressive Stress fc (MPa)


=Fx / Ax 15.94

Calculation Of Allowable Compressive Stress :

Print Time/Date: 07/12/2018 20:09 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 282 of 617
Job No Sheet No Rev
BN/SS/-01 283
Part
Software licensed to BN
Job Title Design of Overhead Gantry Hoarding Truss - 30m Span Ref

By Biswajit Date06-Dec-18 Chd Biswajit


Client Suntony Signage File Final Gantry Truss-30m Date/Time
Span.std 07-Dec-2018 20:06

E (MPa) 200000.00
L/r 155.51
fcc (MPa)
2 2
=π E / λ 81.63
Allowable Compressive Stress fc_allowable (MPa)
1.4 1.4
=0.6fccfy / [(fcc) + (fy) ] 42.47
Interaction ratio
=fc / fc_allowable 0.38
Status SAFE

Print Time/Date: 07/12/2018 20:09 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 283 of 617
Job No Sheet No Rev
BN/SS/-01 284
Part
Software licensed to BN
Job Title Design of Overhead Gantry Hoarding Truss - 30m Span Ref

By Biswajit Date06-Dec-18 Chd Biswajit


Client Suntony Signage File Final Gantry Truss-30m Date/Time
Span.std 07-Dec-2018 20:06

Design Of Member No. 133 As Per IS:800

Input Parameters

Member Section PIP603L

2
Cross Sectional Area Ax (mm ) 523.00
rz (mm) 20.32
ry (mm) 20.32
Unsupported Length - Major Axis For Slenderness Check Lz (mm) 1802.77
Unsupported Length - Minor Axis For Slenderness Check Ly (mm) 1802.77
Yield Stress fy (MPa) 240.00
Allowable Ratio For Interaction Check 1.00

Design Forces

Axial Load Fx (N ) 12488.12


Critical Loadcase No. 3

Details Of Calculation

Slenderness Checking

Lez (mm) 1802.77


Ley (mm) 1802.77
Lez / rz 88.71
Ley / ry 88.71
Actual Slenderness Ratio 88.71
Allowable Slenderness Ratio 180.00
Status SAFE

Check Against Axial Compression For Truss Member

Actual Compressive Stress fc (MPa)


=Fx / Ax 23.88

Calculation Of Allowable Compressive Stress :

Print Time/Date: 07/12/2018 20:09 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 284 of 617
Job No Sheet No Rev
BN/SS/-01 285
Part
Software licensed to BN
Job Title Design of Overhead Gantry Hoarding Truss - 30m Span Ref

By Biswajit Date06-Dec-18 Chd Biswajit


Client Suntony Signage File Final Gantry Truss-30m Date/Time
Span.std 07-Dec-2018 20:06

E (MPa) 200000.00
L/r 88.71
fcc (MPa)
2 2
=π E / λ 250.84
Allowable Compressive Stress fc_allowable (MPa)
1.4 1.4
=0.6fccfy / [(fcc) + (fy) ] 89.69
Interaction ratio
=fc / fc_allowable 0.27
Status SAFE

Print Time/Date: 07/12/2018 20:09 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 285 of 617
Job No Sheet No Rev
BN/SS/-01 286
Part
Software licensed to BN
Job Title Design of Overhead Gantry Hoarding Truss - 30m Span Ref

By Biswajit Date06-Dec-18 Chd Biswajit


Client Suntony Signage File Final Gantry Truss-30m Date/Time
Span.std 07-Dec-2018 20:06

Design Of Member No. 134 As Per IS:800

Input Parameters

Member Section PIP424L

2
Cross Sectional Area Ax (mm ) 325.00
rz (mm) 14.10
ry (mm) 14.10
Unsupported Length - Major Axis For Slenderness Check Lz (mm) 1000.00
Unsupported Length - Minor Axis For Slenderness Check Ly (mm) 1000.00
Yield Stress fy (MPa) 240.00
Allowable Ratio For Interaction Check 1.00

Design Forces

Axial Load Fx (N ) 1587.00


Critical Loadcase No. 3

Details Of Calculation

Slenderness Checking

Lez (mm) 1000.00


Ley (mm) 1000.00
Lez / rz 70.93
Ley / ry 70.93
Actual Slenderness Ratio 70.93
Allowable Slenderness Ratio 180.00
Status SAFE

Check Against Axial Compression For Truss Member

Actual Compressive Stress fc (MPa)


=Fx / Ax 4.88

Calculation Of Allowable Compressive Stress :

Print Time/Date: 07/12/2018 20:09 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 286 of 617
Job No Sheet No Rev
BN/SS/-01 287
Part
Software licensed to BN
Job Title Design of Overhead Gantry Hoarding Truss - 30m Span Ref

By Biswajit Date06-Dec-18 Chd Biswajit


Client Suntony Signage File Final Gantry Truss-30m Date/Time
Span.std 07-Dec-2018 20:06

E (MPa) 200000.00
L/r 70.93
fcc (MPa)
2 2
=π E / λ 392.36
Allowable Compressive Stress fc_allowable (MPa)
1.4 1.4
=0.6fccfy / [(fcc) + (fy) ] 107.66
Interaction ratio
=fc / fc_allowable 0.05
Status SAFE

Print Time/Date: 07/12/2018 20:09 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 287 of 617
Job No Sheet No Rev
BN/SS/-01 288
Part
Software licensed to BN
Job Title Design of Overhead Gantry Hoarding Truss - 30m Span Ref

By Biswajit Date06-Dec-18 Chd Biswajit


Client Suntony Signage File Final Gantry Truss-30m Date/Time
Span.std 07-Dec-2018 20:06

Design Of Member No. 135 As Per IS:800

Input Parameters

Member Section PIP483L

2
Cross Sectional Area Ax (mm ) 414.00
Net section factor 1.00
2
Net Effective Sectional Area Anet (mm ) 414.00
rz (mm) 16.08
ry (mm) 16.08
Unsupported Length - Major Axis For Slenderness Check Lz (mm) 2000.00
Unsupported Length - Minor Axis For Slenderness Check Ly (mm) 2000.00
Yield Stress fy (MPa) 240.00
Allowable Ratio For Interaction Check 1.00

Design Forces

Axial Load Fx (N ) -2095.09


Critical Loadcase No. 3

Details Of Calculation

Slenderness Checking

Lez (mm) 2000.00


Ley (mm) 2000.00
Lez / rz 124.40
Ley / ry 124.40
Actual Slenderness Ratio 124.40
Allowable Slenderness Ratio 400.00
Status SAFE

Check Against Axial Tension For Truss Member

Actual Tensile Stress ft (MPa)


=Fx / Anet 5.06

Print Time/Date: 07/12/2018 20:09 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 288 of 617
Job No Sheet No Rev
BN/SS/-01 289
Part
Software licensed to BN
Job Title Design of Overhead Gantry Hoarding Truss - 30m Span Ref

By Biswajit Date06-Dec-18 Chd Biswajit


Client Suntony Signage File Final Gantry Truss-30m Date/Time
Span.std 07-Dec-2018 20:06

Allowable Tensile Stress ft_allowable (MPa)


=0.60fy 144.00
Interaction ratio
=ft / ft_allowable 0.04
Status SAFE

Print Time/Date: 07/12/2018 20:09 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 289 of 617
Job No Sheet No Rev
BN/SS/-01 290
Part
Software licensed to BN
Job Title Design of Overhead Gantry Hoarding Truss - 30m Span Ref

By Biswajit Date06-Dec-18 Chd Biswajit


Client Suntony Signage File Final Gantry Truss-30m Date/Time
Span.std 07-Dec-2018 20:06

Design Of Member No. 136 As Per IS:800

Input Parameters

Member Section PIP483L

2
Cross Sectional Area Ax (mm ) 414.00
Net section factor 1.00
2
Net Effective Sectional Area Anet (mm ) 414.00
rz (mm) 16.08
ry (mm) 16.08
Unsupported Length - Major Axis For Slenderness Check Lz (mm) 2000.00
Unsupported Length - Minor Axis For Slenderness Check Ly (mm) 2000.00
Yield Stress fy (MPa) 240.00
Allowable Ratio For Interaction Check 1.00

Design Forces

Axial Load Fx (N ) -5509.42


Critical Loadcase No. 3

Details Of Calculation

Slenderness Checking

Lez (mm) 2000.00


Ley (mm) 2000.00
Lez / rz 124.40
Ley / ry 124.40
Actual Slenderness Ratio 124.40
Allowable Slenderness Ratio 400.00
Status SAFE

Check Against Axial Tension For Truss Member

Actual Tensile Stress ft (MPa)


=Fx / Anet 13.31

Print Time/Date: 07/12/2018 20:09 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 290 of 617
Job No Sheet No Rev
BN/SS/-01 291
Part
Software licensed to BN
Job Title Design of Overhead Gantry Hoarding Truss - 30m Span Ref

By Biswajit Date06-Dec-18 Chd Biswajit


Client Suntony Signage File Final Gantry Truss-30m Date/Time
Span.std 07-Dec-2018 20:06

Allowable Tensile Stress ft_allowable (MPa)


=0.60fy 144.00
Interaction ratio
=ft / ft_allowable 0.09
Status SAFE

Print Time/Date: 07/12/2018 20:09 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 291 of 617
Job No Sheet No Rev
BN/SS/-01 292
Part
Software licensed to BN
Job Title Design of Overhead Gantry Hoarding Truss - 30m Span Ref

By Biswajit Date06-Dec-18 Chd Biswajit


Client Suntony Signage File Final Gantry Truss-30m Date/Time
Span.std 07-Dec-2018 20:06

Design Of Member No. 137 As Per IS:800

Input Parameters

Member Section PIP424L

2
Cross Sectional Area Ax (mm ) 325.00
rz (mm) 14.10
ry (mm) 14.10
Unsupported Length - Major Axis For Slenderness Check Lz (mm) 1000.00
Unsupported Length - Minor Axis For Slenderness Check Ly (mm) 1000.00
Yield Stress fy (MPa) 240.00
Allowable Ratio For Interaction Check 1.00

Design Forces

Axial Load Fx (N ) 1206.93


Critical Loadcase No. 3

Details Of Calculation

Slenderness Checking

Lez (mm) 1000.00


Ley (mm) 1000.00
Lez / rz 70.93
Ley / ry 70.93
Actual Slenderness Ratio 70.93
Allowable Slenderness Ratio 180.00
Status SAFE

Check Against Axial Compression For Truss Member

Actual Compressive Stress fc (MPa)


=Fx / Ax 3.71

Calculation Of Allowable Compressive Stress :

Print Time/Date: 07/12/2018 20:09 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 292 of 617
Job No Sheet No Rev
BN/SS/-01 293
Part
Software licensed to BN
Job Title Design of Overhead Gantry Hoarding Truss - 30m Span Ref

By Biswajit Date06-Dec-18 Chd Biswajit


Client Suntony Signage File Final Gantry Truss-30m Date/Time
Span.std 07-Dec-2018 20:06

E (MPa) 200000.00
L/r 70.93
fcc (MPa)
2 2
=π E / λ 392.36
Allowable Compressive Stress fc_allowable (MPa)
1.4 1.4
=0.6fccfy / [(fcc) + (fy) ] 107.66
Interaction ratio
=fc / fc_allowable 0.03
Status SAFE

Print Time/Date: 07/12/2018 20:09 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 293 of 617
Job No Sheet No Rev
BN/SS/-01 294
Part
Software licensed to BN
Job Title Design of Overhead Gantry Hoarding Truss - 30m Span Ref

By Biswajit Date06-Dec-18 Chd Biswajit


Client Suntony Signage File Final Gantry Truss-30m Date/Time
Span.std 07-Dec-2018 20:06

Design Of Member No. 138 As Per IS:800

Input Parameters

Member Section PIP603L

2
Cross Sectional Area Ax (mm ) 523.00
Net section factor 1.00
2
Net Effective Sectional Area Anet (mm ) 523.00
rz (mm) 20.32
ry (mm) 20.32
Unsupported Length - Major Axis For Slenderness Check Lz (mm) 1802.77
Unsupported Length - Minor Axis For Slenderness Check Ly (mm) 1802.77
Yield Stress fy (MPa) 240.00
Allowable Ratio For Interaction Check 1.00

Design Forces

Axial Load Fx (N ) -19608.50


Critical Loadcase No. 3

Details Of Calculation

Slenderness Checking

Lez (mm) 1802.77


Ley (mm) 1802.77
Lez / rz 88.71
Ley / ry 88.71
Actual Slenderness Ratio 88.71
Allowable Slenderness Ratio 400.00
Status SAFE

Check Against Axial Tension For Truss Member

Actual Tensile Stress ft (MPa)


=Fx / Anet 37.49

Print Time/Date: 07/12/2018 20:09 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 294 of 617
Job No Sheet No Rev
BN/SS/-01 295
Part
Software licensed to BN
Job Title Design of Overhead Gantry Hoarding Truss - 30m Span Ref

By Biswajit Date06-Dec-18 Chd Biswajit


Client Suntony Signage File Final Gantry Truss-30m Date/Time
Span.std 07-Dec-2018 20:06

Allowable Tensile Stress ft_allowable (MPa)


=0.60fy 144.00
Interaction ratio
=ft / ft_allowable 0.26
Status SAFE

Print Time/Date: 07/12/2018 20:09 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 295 of 617
Job No Sheet No Rev
BN/SS/-01 296
Part
Software licensed to BN
Job Title Design of Overhead Gantry Hoarding Truss - 30m Span Ref

By Biswajit Date06-Dec-18 Chd Biswajit


Client Suntony Signage File Final Gantry Truss-30m Date/Time
Span.std 07-Dec-2018 20:06

Design Of Member No. 139 As Per IS:800

Input Parameters

Member Section PIP483L

2
Cross Sectional Area Ax (mm ) 414.00
rz (mm) 16.08
ry (mm) 16.08
Unsupported Length - Major Axis For Slenderness Check Lz (mm) 2500.00
Unsupported Length - Minor Axis For Slenderness Check Ly (mm) 2500.00
Yield Stress fy (MPa) 240.00
Allowable Ratio For Interaction Check 1.00

Design Forces

Axial Load Fx (N ) 2983.75


Critical Loadcase No. 3

Details Of Calculation

Slenderness Checking

Lez (mm) 2500.00


Ley (mm) 2500.00
Lez / rz 155.51
Ley / ry 155.51
Actual Slenderness Ratio 155.51
Allowable Slenderness Ratio 180.00
Status SAFE

Check Against Axial Compression For Truss Member

Actual Compressive Stress fc (MPa)


=Fx / Ax 7.21

Calculation Of Allowable Compressive Stress :

Print Time/Date: 07/12/2018 20:09 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 296 of 617
Job No Sheet No Rev
BN/SS/-01 297
Part
Software licensed to BN
Job Title Design of Overhead Gantry Hoarding Truss - 30m Span Ref

By Biswajit Date06-Dec-18 Chd Biswajit


Client Suntony Signage File Final Gantry Truss-30m Date/Time
Span.std 07-Dec-2018 20:06

E (MPa) 200000.00
L/r 155.51
fcc (MPa)
2 2
=π E / λ 81.63
Allowable Compressive Stress fc_allowable (MPa)
1.4 1.4
=0.6fccfy / [(fcc) + (fy) ] 42.47
Interaction ratio
=fc / fc_allowable 0.17
Status SAFE

Print Time/Date: 07/12/2018 20:09 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 297 of 617
Job No Sheet No Rev
BN/SS/-01 298
Part
Software licensed to BN
Job Title Design of Overhead Gantry Hoarding Truss - 30m Span Ref

By Biswajit Date06-Dec-18 Chd Biswajit


Client Suntony Signage File Final Gantry Truss-30m Date/Time
Span.std 07-Dec-2018 20:06

Design Of Member No. 140 As Per IS:800

Input Parameters

Member Section PIP483L

2
Cross Sectional Area Ax (mm ) 414.00
rz (mm) 16.08
ry (mm) 16.08
Unsupported Length - Major Axis For Slenderness Check Lz (mm) 2500.00
Unsupported Length - Minor Axis For Slenderness Check Ly (mm) 2500.00
Yield Stress fy (MPa) 240.00
Allowable Ratio For Interaction Check 1.00

Design Forces

Axial Load Fx (N ) 6253.10


Critical Loadcase No. 3

Details Of Calculation

Slenderness Checking

Lez (mm) 2500.00


Ley (mm) 2500.00
Lez / rz 155.51
Ley / ry 155.51
Actual Slenderness Ratio 155.51
Allowable Slenderness Ratio 180.00
Status SAFE

Check Against Axial Compression For Truss Member

Actual Compressive Stress fc (MPa)


=Fx / Ax 15.10

Calculation Of Allowable Compressive Stress :

Print Time/Date: 07/12/2018 20:09 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 298 of 617
Job No Sheet No Rev
BN/SS/-01 299
Part
Software licensed to BN
Job Title Design of Overhead Gantry Hoarding Truss - 30m Span Ref

By Biswajit Date06-Dec-18 Chd Biswajit


Client Suntony Signage File Final Gantry Truss-30m Date/Time
Span.std 07-Dec-2018 20:06

E (MPa) 200000.00
L/r 155.51
fcc (MPa)
2 2
=π E / λ 81.63
Allowable Compressive Stress fc_allowable (MPa)
1.4 1.4
=0.6fccfy / [(fcc) + (fy) ] 42.47
Interaction ratio
=fc / fc_allowable 0.36
Status SAFE

Print Time/Date: 07/12/2018 20:09 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 299 of 617
Job No Sheet No Rev
BN/SS/-01 300
Part
Software licensed to BN
Job Title Design of Overhead Gantry Hoarding Truss - 30m Span Ref

By Biswajit Date06-Dec-18 Chd Biswajit


Client Suntony Signage File Final Gantry Truss-30m Date/Time
Span.std 07-Dec-2018 20:06

Design Of Member No. 141 As Per IS:800

Input Parameters

Member Section PIP603L

2
Cross Sectional Area Ax (mm ) 523.00
Net section factor 1.00
2
Net Effective Sectional Area Anet (mm ) 523.00
rz (mm) 20.32
ry (mm) 20.32
Unsupported Length - Major Axis For Slenderness Check Lz (mm) 1802.77
Unsupported Length - Minor Axis For Slenderness Check Ly (mm) 1802.77
Yield Stress fy (MPa) 240.00
Allowable Ratio For Interaction Check 1.00

Design Forces

Axial Load Fx (N ) -14663.95


Critical Loadcase No. 3

Details Of Calculation

Slenderness Checking

Lez (mm) 1802.77


Ley (mm) 1802.77
Lez / rz 88.71
Ley / ry 88.71
Actual Slenderness Ratio 88.71
Allowable Slenderness Ratio 400.00
Status SAFE

Check Against Axial Tension For Truss Member

Actual Tensile Stress ft (MPa)


=Fx / Anet 28.04

Print Time/Date: 07/12/2018 20:09 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 300 of 617
Job No Sheet No Rev
BN/SS/-01 301
Part
Software licensed to BN
Job Title Design of Overhead Gantry Hoarding Truss - 30m Span Ref

By Biswajit Date06-Dec-18 Chd Biswajit


Client Suntony Signage File Final Gantry Truss-30m Date/Time
Span.std 07-Dec-2018 20:06

Allowable Tensile Stress ft_allowable (MPa)


=0.60fy 144.00
Interaction ratio
=ft / ft_allowable 0.19
Status SAFE

Print Time/Date: 07/12/2018 20:09 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 301 of 617
Job No Sheet No Rev
BN/SS/-01 302
Part
Software licensed to BN
Job Title Design of Overhead Gantry Hoarding Truss - 30m Span Ref

By Biswajit Date06-Dec-18 Chd Biswajit


Client Suntony Signage File Final Gantry Truss-30m Date/Time
Span.std 07-Dec-2018 20:06

Design Of Member No. 142 As Per IS:800

Input Parameters

Member Section PIP424L

2
Cross Sectional Area Ax (mm ) 325.00
Net section factor 1.00
2
Net Effective Sectional Area Anet (mm ) 325.00
rz (mm) 14.10
ry (mm) 14.10
Unsupported Length - Major Axis For Slenderness Check Lz (mm) 1000.00
Unsupported Length - Minor Axis For Slenderness Check Ly (mm) 1000.00
Yield Stress fy (MPa) 240.00
Allowable Ratio For Interaction Check 1.00

Design Forces

Axial Load Fx (N ) -283.59


Critical Loadcase No. 3

Details Of Calculation

Slenderness Checking

Lez (mm) 1000.00


Ley (mm) 1000.00
Lez / rz 70.93
Ley / ry 70.93
Actual Slenderness Ratio 70.93
Allowable Slenderness Ratio 400.00
Status SAFE

Check Against Axial Tension For Truss Member

Actual Tensile Stress ft (MPa)


=Fx / Anet 0.87

Print Time/Date: 07/12/2018 20:09 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 302 of 617
Job No Sheet No Rev
BN/SS/-01 303
Part
Software licensed to BN
Job Title Design of Overhead Gantry Hoarding Truss - 30m Span Ref

By Biswajit Date06-Dec-18 Chd Biswajit


Client Suntony Signage File Final Gantry Truss-30m Date/Time
Span.std 07-Dec-2018 20:06

Allowable Tensile Stress ft_allowable (MPa)


=0.60fy 144.00
Interaction ratio
=ft / ft_allowable 0.01
Status SAFE

Print Time/Date: 07/12/2018 20:09 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 303 of 617
Job No Sheet No Rev
BN/SS/-01 304
Part
Software licensed to BN
Job Title Design of Overhead Gantry Hoarding Truss - 30m Span Ref

By Biswajit Date06-Dec-18 Chd Biswajit


Client Suntony Signage File Final Gantry Truss-30m Date/Time
Span.std 07-Dec-2018 20:06

Design Of Member No. 143 As Per IS:800

Input Parameters

Member Section PIP483L

2
Cross Sectional Area Ax (mm ) 414.00
Net section factor 1.00
2
Net Effective Sectional Area Anet (mm ) 414.00
rz (mm) 16.08
ry (mm) 16.08
Unsupported Length - Major Axis For Slenderness Check Lz (mm) 2000.00
Unsupported Length - Minor Axis For Slenderness Check Ly (mm) 2000.00
Yield Stress fy (MPa) 240.00
Allowable Ratio For Interaction Check 1.00

Design Forces

Axial Load Fx (N ) -3220.74


Critical Loadcase No. 3

Details Of Calculation

Slenderness Checking

Lez (mm) 2000.00


Ley (mm) 2000.00
Lez / rz 124.40
Ley / ry 124.40
Actual Slenderness Ratio 124.40
Allowable Slenderness Ratio 400.00
Status SAFE

Check Against Axial Tension For Truss Member

Actual Tensile Stress ft (MPa)


=Fx / Anet 7.78

Print Time/Date: 07/12/2018 20:09 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 304 of 617
Job No Sheet No Rev
BN/SS/-01 305
Part
Software licensed to BN
Job Title Design of Overhead Gantry Hoarding Truss - 30m Span Ref

By Biswajit Date06-Dec-18 Chd Biswajit


Client Suntony Signage File Final Gantry Truss-30m Date/Time
Span.std 07-Dec-2018 20:06

Allowable Tensile Stress ft_allowable (MPa)


=0.60fy 144.00
Interaction ratio
=ft / ft_allowable 0.05
Status SAFE

Print Time/Date: 07/12/2018 20:09 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 305 of 617
Job No Sheet No Rev
BN/SS/-01 306
Part
Software licensed to BN
Job Title Design of Overhead Gantry Hoarding Truss - 30m Span Ref

By Biswajit Date06-Dec-18 Chd Biswajit


Client Suntony Signage File Final Gantry Truss-30m Date/Time
Span.std 07-Dec-2018 20:06

Design Of Member No. 144 As Per IS:800

Input Parameters

Member Section PIP483L

2
Cross Sectional Area Ax (mm ) 414.00
Net section factor 1.00
2
Net Effective Sectional Area Anet (mm ) 414.00
rz (mm) 16.08
ry (mm) 16.08
Unsupported Length - Major Axis For Slenderness Check Lz (mm) 2000.00
Unsupported Length - Minor Axis For Slenderness Check Ly (mm) 2000.00
Yield Stress fy (MPa) 240.00
Allowable Ratio For Interaction Check 1.00

Design Forces

Axial Load Fx (N ) -5307.76


Critical Loadcase No. 3

Details Of Calculation

Slenderness Checking

Lez (mm) 2000.00


Ley (mm) 2000.00
Lez / rz 124.40
Ley / ry 124.40
Actual Slenderness Ratio 124.40
Allowable Slenderness Ratio 400.00
Status SAFE

Check Against Axial Tension For Truss Member

Actual Tensile Stress ft (MPa)


=Fx / Anet 12.82

Print Time/Date: 07/12/2018 20:09 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 306 of 617
Job No Sheet No Rev
BN/SS/-01 307
Part
Software licensed to BN
Job Title Design of Overhead Gantry Hoarding Truss - 30m Span Ref

By Biswajit Date06-Dec-18 Chd Biswajit


Client Suntony Signage File Final Gantry Truss-30m Date/Time
Span.std 07-Dec-2018 20:06

Allowable Tensile Stress ft_allowable (MPa)


=0.60fy 144.00
Interaction ratio
=ft / ft_allowable 0.09
Status SAFE

Print Time/Date: 07/12/2018 20:09 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 307 of 617
Job No Sheet No Rev
BN/SS/-01 308
Part
Software licensed to BN
Job Title Design of Overhead Gantry Hoarding Truss - 30m Span Ref

By Biswajit Date06-Dec-18 Chd Biswajit


Client Suntony Signage File Final Gantry Truss-30m Date/Time
Span.std 07-Dec-2018 20:06

Design Of Member No. 145 As Per IS:800

Input Parameters

Member Section PIP424L

2
Cross Sectional Area Ax (mm ) 0.00
rz (mm) 14.10
ry (mm) 14.10
Unsupported Length - Major Axis For Slenderness Check Lz (mm) 1000.00
Unsupported Length - Minor Axis For Slenderness Check Ly (mm) 1000.00
Yield Stress fy (MPa) 0.00
Allowable Ratio For Interaction Check 1.00

Design Forces

Axial Load Fx (N ) 0.00


Critical Loadcase No. 0

Details Of Calculation

Slenderness Checking

Lez (mm) 1000.00


Ley (mm) 1000.00
Lez / rz 70.93
Ley / ry 70.93
Actual Slenderness Ratio 70.93
Allowable Slenderness Ratio 400.00
Status SAFE

Check Against Axial Compression For Truss Member

Actual Compressive Stress fc (MPa)


=Fx / Ax 0.00

Calculation Of Allowable Compressive Stress :

Print Time/Date: 07/12/2018 20:09 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 308 of 617
Job No Sheet No Rev
BN/SS/-01 309
Part
Software licensed to BN
Job Title Design of Overhead Gantry Hoarding Truss - 30m Span Ref

By Biswajit Date06-Dec-18 Chd Biswajit


Client Suntony Signage File Final Gantry Truss-30m Date/Time
Span.std 07-Dec-2018 20:06

E (MPa) 200000.00
L/r 70.93
fcc (MPa)
2 2
=π E / λ 392.36
Allowable Compressive Stress fc_allowable (MPa)
1.4 1.4
=0.6fccfy / [(fcc) + (fy) ] 0.00
Interaction ratio
=fc / fc_allowable 0.00
Status SAFE

Print Time/Date: 07/12/2018 20:09 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 309 of 617
Job No Sheet No Rev
BN/SS/-01 310
Part
Software licensed to BN
Job Title Design of Overhead Gantry Hoarding Truss - 30m Span Ref

By Biswajit Date06-Dec-18 Chd Biswajit


Client Suntony Signage File Final Gantry Truss-30m Date/Time
Span.std 07-Dec-2018 20:06

Design Of Member No. 146 As Per IS:800

Input Parameters

Member Section PIP603L

2
Cross Sectional Area Ax (mm ) 523.00
rz (mm) 20.32
ry (mm) 20.32
Unsupported Length - Major Axis For Slenderness Check Lz (mm) 1802.77
Unsupported Length - Minor Axis For Slenderness Check Ly (mm) 1802.77
Yield Stress fy (MPa) 240.00
Allowable Ratio For Interaction Check 1.00

Design Forces

Axial Load Fx (N ) 22980.77


Critical Loadcase No. 3

Details Of Calculation

Slenderness Checking

Lez (mm) 1802.77


Ley (mm) 1802.77
Lez / rz 88.71
Ley / ry 88.71
Actual Slenderness Ratio 88.71
Allowable Slenderness Ratio 180.00
Status SAFE

Check Against Axial Compression For Truss Member

Actual Compressive Stress fc (MPa)


=Fx / Ax 43.94

Calculation Of Allowable Compressive Stress :

Print Time/Date: 07/12/2018 20:09 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 310 of 617
Job No Sheet No Rev
BN/SS/-01 311
Part
Software licensed to BN
Job Title Design of Overhead Gantry Hoarding Truss - 30m Span Ref

By Biswajit Date06-Dec-18 Chd Biswajit


Client Suntony Signage File Final Gantry Truss-30m Date/Time
Span.std 07-Dec-2018 20:06

E (MPa) 200000.00
L/r 88.71
fcc (MPa)
2 2
=π E / λ 250.84
Allowable Compressive Stress fc_allowable (MPa)
1.4 1.4
=0.6fccfy / [(fcc) + (fy) ] 89.69
Interaction ratio
=fc / fc_allowable 0.49
Status SAFE

Print Time/Date: 07/12/2018 20:09 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 311 of 617
Job No Sheet No Rev
BN/SS/-01 312
Part
Software licensed to BN
Job Title Design of Overhead Gantry Hoarding Truss - 30m Span Ref

By Biswajit Date06-Dec-18 Chd Biswajit


Client Suntony Signage File Final Gantry Truss-30m Date/Time
Span.std 07-Dec-2018 20:06

Design Of Member No. 147 As Per IS:800

Input Parameters

Member Section PIP483L

2
Cross Sectional Area Ax (mm ) 414.00
rz (mm) 16.08
ry (mm) 16.08
Unsupported Length - Major Axis For Slenderness Check Lz (mm) 2500.00
Unsupported Length - Minor Axis For Slenderness Check Ly (mm) 2500.00
Yield Stress fy (MPa) 240.00
Allowable Ratio For Interaction Check 1.00

Design Forces

Axial Load Fx (N ) 4295.76


Critical Loadcase No. 3

Details Of Calculation

Slenderness Checking

Lez (mm) 2500.00


Ley (mm) 2500.00
Lez / rz 155.51
Ley / ry 155.51
Actual Slenderness Ratio 155.51
Allowable Slenderness Ratio 180.00
Status SAFE

Check Against Axial Compression For Truss Member

Actual Compressive Stress fc (MPa)


=Fx / Ax 10.38

Calculation Of Allowable Compressive Stress :

Print Time/Date: 07/12/2018 20:09 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 312 of 617
Job No Sheet No Rev
BN/SS/-01 313
Part
Software licensed to BN
Job Title Design of Overhead Gantry Hoarding Truss - 30m Span Ref

By Biswajit Date06-Dec-18 Chd Biswajit


Client Suntony Signage File Final Gantry Truss-30m Date/Time
Span.std 07-Dec-2018 20:06

E (MPa) 200000.00
L/r 155.51
fcc (MPa)
2 2
=π E / λ 81.63
Allowable Compressive Stress fc_allowable (MPa)
1.4 1.4
=0.6fccfy / [(fcc) + (fy) ] 42.47
Interaction ratio
=fc / fc_allowable 0.24
Status SAFE

Print Time/Date: 07/12/2018 20:09 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 313 of 617
Job No Sheet No Rev
BN/SS/-01 314
Part
Software licensed to BN
Job Title Design of Overhead Gantry Hoarding Truss - 30m Span Ref

By Biswajit Date06-Dec-18 Chd Biswajit


Client Suntony Signage File Final Gantry Truss-30m Date/Time
Span.std 07-Dec-2018 20:06

Design Of Member No. 148 As Per IS:800

Input Parameters

Member Section PIP483L

2
Cross Sectional Area Ax (mm ) 414.00
rz (mm) 16.08
ry (mm) 16.08
Unsupported Length - Major Axis For Slenderness Check Lz (mm) 2500.00
Unsupported Length - Minor Axis For Slenderness Check Ly (mm) 2500.00
Yield Stress fy (MPa) 240.00
Allowable Ratio For Interaction Check 1.00

Design Forces

Axial Load Fx (N ) 6337.28


Critical Loadcase No. 3

Details Of Calculation

Slenderness Checking

Lez (mm) 2500.00


Ley (mm) 2500.00
Lez / rz 155.51
Ley / ry 155.51
Actual Slenderness Ratio 155.51
Allowable Slenderness Ratio 180.00
Status SAFE

Check Against Axial Compression For Truss Member

Actual Compressive Stress fc (MPa)


=Fx / Ax 15.31

Calculation Of Allowable Compressive Stress :

Print Time/Date: 07/12/2018 20:09 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 314 of 617
Job No Sheet No Rev
BN/SS/-01 315
Part
Software licensed to BN
Job Title Design of Overhead Gantry Hoarding Truss - 30m Span Ref

By Biswajit Date06-Dec-18 Chd Biswajit


Client Suntony Signage File Final Gantry Truss-30m Date/Time
Span.std 07-Dec-2018 20:06

E (MPa) 200000.00
L/r 155.51
fcc (MPa)
2 2
=π E / λ 81.63
Allowable Compressive Stress fc_allowable (MPa)
1.4 1.4
=0.6fccfy / [(fcc) + (fy) ] 42.47
Interaction ratio
=fc / fc_allowable 0.36
Status SAFE

Print Time/Date: 07/12/2018 20:09 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 315 of 617
Job No Sheet No Rev
BN/SS/-01 316
Part
Software licensed to BN
Job Title Design of Overhead Gantry Hoarding Truss - 30m Span Ref

By Biswajit Date06-Dec-18 Chd Biswajit


Client Suntony Signage File Final Gantry Truss-30m Date/Time
Span.std 07-Dec-2018 20:06

Design Of Member No. 149 As Per IS:800

Input Parameters

Member Section PIP603L

2
Cross Sectional Area Ax (mm ) 523.00
rz (mm) 20.32
ry (mm) 20.32
Unsupported Length - Major Axis For Slenderness Check Lz (mm) 1802.77
Unsupported Length - Minor Axis For Slenderness Check Ly (mm) 1802.77
Yield Stress fy (MPa) 240.00
Allowable Ratio For Interaction Check 1.00

Design Forces

Axial Load Fx (N ) 17013.72


Critical Loadcase No. 3

Details Of Calculation

Slenderness Checking

Lez (mm) 1802.77


Ley (mm) 1802.77
Lez / rz 88.71
Ley / ry 88.71
Actual Slenderness Ratio 88.71
Allowable Slenderness Ratio 180.00
Status SAFE

Check Against Axial Compression For Truss Member

Actual Compressive Stress fc (MPa)


=Fx / Ax 32.53

Calculation Of Allowable Compressive Stress :

Print Time/Date: 07/12/2018 20:09 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 316 of 617
Job No Sheet No Rev
BN/SS/-01 317
Part
Software licensed to BN
Job Title Design of Overhead Gantry Hoarding Truss - 30m Span Ref

By Biswajit Date06-Dec-18 Chd Biswajit


Client Suntony Signage File Final Gantry Truss-30m Date/Time
Span.std 07-Dec-2018 20:06

E (MPa) 200000.00
L/r 88.71
fcc (MPa)
2 2
=π E / λ 250.84
Allowable Compressive Stress fc_allowable (MPa)
1.4 1.4
=0.6fccfy / [(fcc) + (fy) ] 89.69
Interaction ratio
=fc / fc_allowable 0.36
Status SAFE

Print Time/Date: 07/12/2018 20:09 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 317 of 617
Job No Sheet No Rev
BN/SS/-01 318
Part
Software licensed to BN
Job Title Design of Overhead Gantry Hoarding Truss - 30m Span Ref

By Biswajit Date06-Dec-18 Chd Biswajit


Client Suntony Signage File Final Gantry Truss-30m Date/Time
Span.std 07-Dec-2018 20:06

Design Of Member No. 150 As Per IS:800

Input Parameters

Member Section PIP424L

2
Cross Sectional Area Ax (mm ) 325.00
rz (mm) 14.10
ry (mm) 14.10
Unsupported Length - Major Axis For Slenderness Check Lz (mm) 1000.00
Unsupported Length - Minor Axis For Slenderness Check Ly (mm) 1000.00
Yield Stress fy (MPa) 240.00
Allowable Ratio For Interaction Check 1.00

Design Forces

Axial Load Fx (N ) 1587.00


Critical Loadcase No. 3

Details Of Calculation

Slenderness Checking

Lez (mm) 1000.00


Ley (mm) 1000.00
Lez / rz 70.93
Ley / ry 70.93
Actual Slenderness Ratio 70.93
Allowable Slenderness Ratio 180.00
Status SAFE

Check Against Axial Compression For Truss Member

Actual Compressive Stress fc (MPa)


=Fx / Ax 4.88

Calculation Of Allowable Compressive Stress :

Print Time/Date: 07/12/2018 20:09 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 318 of 617
Job No Sheet No Rev
BN/SS/-01 319
Part
Software licensed to BN
Job Title Design of Overhead Gantry Hoarding Truss - 30m Span Ref

By Biswajit Date06-Dec-18 Chd Biswajit


Client Suntony Signage File Final Gantry Truss-30m Date/Time
Span.std 07-Dec-2018 20:06

E (MPa) 200000.00
L/r 70.93
fcc (MPa)
2 2
=π E / λ 392.36
Allowable Compressive Stress fc_allowable (MPa)
1.4 1.4
=0.6fccfy / [(fcc) + (fy) ] 107.66
Interaction ratio
=fc / fc_allowable 0.05
Status SAFE

Print Time/Date: 07/12/2018 20:09 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 319 of 617
Job No Sheet No Rev
BN/SS/-01 320
Part
Software licensed to BN
Job Title Design of Overhead Gantry Hoarding Truss - 30m Span Ref

By Biswajit Date06-Dec-18 Chd Biswajit


Client Suntony Signage File Final Gantry Truss-30m Date/Time
Span.std 07-Dec-2018 20:06

Design Of Member No. 151 As Per IS:800

Input Parameters

Member Section PIP483L

2
Cross Sectional Area Ax (mm ) 414.00
Net section factor 1.00
2
Net Effective Sectional Area Anet (mm ) 414.00
rz (mm) 16.08
ry (mm) 16.08
Unsupported Length - Major Axis For Slenderness Check Lz (mm) 2000.00
Unsupported Length - Minor Axis For Slenderness Check Ly (mm) 2000.00
Yield Stress fy (MPa) 240.00
Allowable Ratio For Interaction Check 1.00

Design Forces

Axial Load Fx (N ) -4378.21


Critical Loadcase No. 3

Details Of Calculation

Slenderness Checking

Lez (mm) 2000.00


Ley (mm) 2000.00
Lez / rz 124.40
Ley / ry 124.40
Actual Slenderness Ratio 124.40
Allowable Slenderness Ratio 400.00
Status SAFE

Check Against Axial Tension For Truss Member

Actual Tensile Stress ft (MPa)


=Fx / Anet 10.58

Print Time/Date: 07/12/2018 20:09 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 320 of 617
Job No Sheet No Rev
BN/SS/-01 321
Part
Software licensed to BN
Job Title Design of Overhead Gantry Hoarding Truss - 30m Span Ref

By Biswajit Date06-Dec-18 Chd Biswajit


Client Suntony Signage File Final Gantry Truss-30m Date/Time
Span.std 07-Dec-2018 20:06

Allowable Tensile Stress ft_allowable (MPa)


=0.60fy 144.00
Interaction ratio
=ft / ft_allowable 0.07
Status SAFE

Print Time/Date: 07/12/2018 20:09 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 321 of 617
Job No Sheet No Rev
BN/SS/-01 322
Part
Software licensed to BN
Job Title Design of Overhead Gantry Hoarding Truss - 30m Span Ref

By Biswajit Date06-Dec-18 Chd Biswajit


Client Suntony Signage File Final Gantry Truss-30m Date/Time
Span.std 07-Dec-2018 20:06

Design Of Member No. 152 As Per IS:800

Input Parameters

Member Section PIP483L

2
Cross Sectional Area Ax (mm ) 414.00
Net section factor 1.00
2
Net Effective Sectional Area Anet (mm ) 414.00
rz (mm) 16.08
ry (mm) 16.08
Unsupported Length - Major Axis For Slenderness Check Lz (mm) 2000.00
Unsupported Length - Minor Axis For Slenderness Check Ly (mm) 2000.00
Yield Stress fy (MPa) 240.00
Allowable Ratio For Interaction Check 1.00

Design Forces

Axial Load Fx (N ) -5299.04


Critical Loadcase No. 3

Details Of Calculation

Slenderness Checking

Lez (mm) 2000.00


Ley (mm) 2000.00
Lez / rz 124.40
Ley / ry 124.40
Actual Slenderness Ratio 124.40
Allowable Slenderness Ratio 400.00
Status SAFE

Check Against Axial Tension For Truss Member

Actual Tensile Stress ft (MPa)


=Fx / Anet 12.80

Print Time/Date: 07/12/2018 20:09 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 322 of 617
Job No Sheet No Rev
BN/SS/-01 323
Part
Software licensed to BN
Job Title Design of Overhead Gantry Hoarding Truss - 30m Span Ref

By Biswajit Date06-Dec-18 Chd Biswajit


Client Suntony Signage File Final Gantry Truss-30m Date/Time
Span.std 07-Dec-2018 20:06

Allowable Tensile Stress ft_allowable (MPa)


=0.60fy 144.00
Interaction ratio
=ft / ft_allowable 0.09
Status SAFE

Print Time/Date: 07/12/2018 20:09 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 323 of 617
Job No Sheet No Rev
BN/SS/-01 324
Part
Software licensed to BN
Job Title Design of Overhead Gantry Hoarding Truss - 30m Span Ref

By Biswajit Date06-Dec-18 Chd Biswajit


Client Suntony Signage File Final Gantry Truss-30m Date/Time
Span.std 07-Dec-2018 20:06

Design Of Member No. 153 As Per IS:800

Input Parameters

Member Section PIP424L

2
Cross Sectional Area Ax (mm ) 325.00
rz (mm) 14.10
ry (mm) 14.10
Unsupported Length - Major Axis For Slenderness Check Lz (mm) 1000.00
Unsupported Length - Minor Axis For Slenderness Check Ly (mm) 1000.00
Yield Stress fy (MPa) 240.00
Allowable Ratio For Interaction Check 1.00

Design Forces

Axial Load Fx (N ) 1287.50


Critical Loadcase No. 3

Details Of Calculation

Slenderness Checking

Lez (mm) 1000.00


Ley (mm) 1000.00
Lez / rz 70.93
Ley / ry 70.93
Actual Slenderness Ratio 70.93
Allowable Slenderness Ratio 180.00
Status SAFE

Check Against Axial Compression For Truss Member

Actual Compressive Stress fc (MPa)


=Fx / Ax 3.96

Calculation Of Allowable Compressive Stress :

Print Time/Date: 07/12/2018 20:09 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 324 of 617
Job No Sheet No Rev
BN/SS/-01 325
Part
Software licensed to BN
Job Title Design of Overhead Gantry Hoarding Truss - 30m Span Ref

By Biswajit Date06-Dec-18 Chd Biswajit


Client Suntony Signage File Final Gantry Truss-30m Date/Time
Span.std 07-Dec-2018 20:06

E (MPa) 200000.00
L/r 70.93
fcc (MPa)
2 2
=π E / λ 392.36
Allowable Compressive Stress fc_allowable (MPa)
1.4 1.4
=0.6fccfy / [(fcc) + (fy) ] 107.66
Interaction ratio
=fc / fc_allowable 0.04
Status SAFE

Print Time/Date: 07/12/2018 20:09 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 325 of 617
Job No Sheet No Rev
BN/SS/-01 326
Part
Software licensed to BN
Job Title Design of Overhead Gantry Hoarding Truss - 30m Span Ref

By Biswajit Date06-Dec-18 Chd Biswajit


Client Suntony Signage File Final Gantry Truss-30m Date/Time
Span.std 07-Dec-2018 20:06

Design Of Member No. 154 As Per IS:800

Input Parameters

Member Section PIP603L

2
Cross Sectional Area Ax (mm ) 523.00
Net section factor 1.00
2
Net Effective Sectional Area Anet (mm ) 523.00
rz (mm) 20.32
ry (mm) 20.32
Unsupported Length - Major Axis For Slenderness Check Lz (mm) 1802.77
Unsupported Length - Minor Axis For Slenderness Check Ly (mm) 1802.77
Yield Stress fy (MPa) 240.00
Allowable Ratio For Interaction Check 1.00

Design Forces

Axial Load Fx (N ) -26381.67


Critical Loadcase No. 3

Details Of Calculation

Slenderness Checking

Lez (mm) 1802.77


Ley (mm) 1802.77
Lez / rz 88.71
Ley / ry 88.71
Actual Slenderness Ratio 88.71
Allowable Slenderness Ratio 400.00
Status SAFE

Check Against Axial Tension For Truss Member

Actual Tensile Stress ft (MPa)


=Fx / Anet 50.44

Print Time/Date: 07/12/2018 20:09 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 326 of 617
Job No Sheet No Rev
BN/SS/-01 327
Part
Software licensed to BN
Job Title Design of Overhead Gantry Hoarding Truss - 30m Span Ref

By Biswajit Date06-Dec-18 Chd Biswajit


Client Suntony Signage File Final Gantry Truss-30m Date/Time
Span.std 07-Dec-2018 20:06

Allowable Tensile Stress ft_allowable (MPa)


=0.60fy 144.00
Interaction ratio
=ft / ft_allowable 0.35
Status SAFE

Print Time/Date: 07/12/2018 20:09 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 327 of 617
Job No Sheet No Rev
BN/SS/-01 328
Part
Software licensed to BN
Job Title Design of Overhead Gantry Hoarding Truss - 30m Span Ref

By Biswajit Date06-Dec-18 Chd Biswajit


Client Suntony Signage File Final Gantry Truss-30m Date/Time
Span.std 07-Dec-2018 20:06

Design Of Member No. 155 As Per IS:800

Input Parameters

Member Section PIP483L

2
Cross Sectional Area Ax (mm ) 414.00
rz (mm) 16.08
ry (mm) 16.08
Unsupported Length - Major Axis For Slenderness Check Lz (mm) 2500.00
Unsupported Length - Minor Axis For Slenderness Check Ly (mm) 2500.00
Yield Stress fy (MPa) 240.00
Allowable Ratio For Interaction Check 1.00

Design Forces

Axial Load Fx (N ) 5837.65


Critical Loadcase No. 3

Details Of Calculation

Slenderness Checking

Lez (mm) 2500.00


Ley (mm) 2500.00
Lez / rz 155.51
Ley / ry 155.51
Actual Slenderness Ratio 155.51
Allowable Slenderness Ratio 180.00
Status SAFE

Check Against Axial Compression For Truss Member

Actual Compressive Stress fc (MPa)


=Fx / Ax 14.10

Calculation Of Allowable Compressive Stress :

Print Time/Date: 07/12/2018 20:09 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 328 of 617
Job No Sheet No Rev
BN/SS/-01 329
Part
Software licensed to BN
Job Title Design of Overhead Gantry Hoarding Truss - 30m Span Ref

By Biswajit Date06-Dec-18 Chd Biswajit


Client Suntony Signage File Final Gantry Truss-30m Date/Time
Span.std 07-Dec-2018 20:06

E (MPa) 200000.00
L/r 155.51
fcc (MPa)
2 2
=π E / λ 81.63
Allowable Compressive Stress fc_allowable (MPa)
1.4 1.4
=0.6fccfy / [(fcc) + (fy) ] 42.47
Interaction ratio
=fc / fc_allowable 0.33
Status SAFE

Print Time/Date: 07/12/2018 20:09 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 329 of 617
Job No Sheet No Rev
BN/SS/-01 330
Part
Software licensed to BN
Job Title Design of Overhead Gantry Hoarding Truss - 30m Span Ref

By Biswajit Date06-Dec-18 Chd Biswajit


Client Suntony Signage File Final Gantry Truss-30m Date/Time
Span.std 07-Dec-2018 20:06

Design Of Member No. 156 As Per IS:800

Input Parameters

Member Section PIP483L

2
Cross Sectional Area Ax (mm ) 414.00
rz (mm) 16.08
ry (mm) 16.08
Unsupported Length - Major Axis For Slenderness Check Lz (mm) 2500.00
Unsupported Length - Minor Axis For Slenderness Check Ly (mm) 2500.00
Yield Stress fy (MPa) 240.00
Allowable Ratio For Interaction Check 1.00

Design Forces

Axial Load Fx (N ) 6191.55


Critical Loadcase No. 3

Details Of Calculation

Slenderness Checking

Lez (mm) 2500.00


Ley (mm) 2500.00
Lez / rz 155.51
Ley / ry 155.51
Actual Slenderness Ratio 155.51
Allowable Slenderness Ratio 180.00
Status SAFE

Check Against Axial Compression For Truss Member

Actual Compressive Stress fc (MPa)


=Fx / Ax 14.96

Calculation Of Allowable Compressive Stress :

Print Time/Date: 07/12/2018 20:09 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 330 of 617
Job No Sheet No Rev
BN/SS/-01 331
Part
Software licensed to BN
Job Title Design of Overhead Gantry Hoarding Truss - 30m Span Ref

By Biswajit Date06-Dec-18 Chd Biswajit


Client Suntony Signage File Final Gantry Truss-30m Date/Time
Span.std 07-Dec-2018 20:06

E (MPa) 200000.00
L/r 155.51
fcc (MPa)
2 2
=π E / λ 81.63
Allowable Compressive Stress fc_allowable (MPa)
1.4 1.4
=0.6fccfy / [(fcc) + (fy) ] 42.47
Interaction ratio
=fc / fc_allowable 0.35
Status SAFE

Print Time/Date: 07/12/2018 20:09 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 331 of 617
Job No Sheet No Rev
BN/SS/-01 332
Part
Software licensed to BN
Job Title Design of Overhead Gantry Hoarding Truss - 30m Span Ref

By Biswajit Date06-Dec-18 Chd Biswajit


Client Suntony Signage File Final Gantry Truss-30m Date/Time
Span.std 07-Dec-2018 20:06

Design Of Member No. 157 As Per IS:800

Input Parameters

Member Section PIP603L

2
Cross Sectional Area Ax (mm ) 523.00
Net section factor 1.00
2
Net Effective Sectional Area Anet (mm ) 523.00
rz (mm) 20.32
ry (mm) 20.32
Unsupported Length - Major Axis For Slenderness Check Lz (mm) 1802.77
Unsupported Length - Minor Axis For Slenderness Check Ly (mm) 1802.77
Yield Stress fy (MPa) 240.00
Allowable Ratio For Interaction Check 1.00

Design Forces

Axial Load Fx (N ) -19334.77


Critical Loadcase No. 3

Details Of Calculation

Slenderness Checking

Lez (mm) 1802.77


Ley (mm) 1802.77
Lez / rz 88.71
Ley / ry 88.71
Actual Slenderness Ratio 88.71
Allowable Slenderness Ratio 400.00
Status SAFE

Check Against Axial Tension For Truss Member

Actual Tensile Stress ft (MPa)


=Fx / Anet 36.97

Print Time/Date: 07/12/2018 20:09 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 332 of 617
Job No Sheet No Rev
BN/SS/-01 333
Part
Software licensed to BN
Job Title Design of Overhead Gantry Hoarding Truss - 30m Span Ref

By Biswajit Date06-Dec-18 Chd Biswajit


Client Suntony Signage File Final Gantry Truss-30m Date/Time
Span.std 07-Dec-2018 20:06

Allowable Tensile Stress ft_allowable (MPa)


=0.60fy 144.00
Interaction ratio
=ft / ft_allowable 0.26
Status SAFE

Print Time/Date: 07/12/2018 20:09 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 333 of 617
Job No Sheet No Rev
BN/SS/-01 334
Part
Software licensed to BN
Job Title Design of Overhead Gantry Hoarding Truss - 30m Span Ref

By Biswajit Date06-Dec-18 Chd Biswajit


Client Suntony Signage File Final Gantry Truss-30m Date/Time
Span.std 07-Dec-2018 20:06

Design Of Member No. 158 As Per IS:800

Input Parameters

Member Section PIP424L

2
Cross Sectional Area Ax (mm ) 325.00
rz (mm) 14.10
ry (mm) 14.10
Unsupported Length - Major Axis For Slenderness Check Lz (mm) 1000.00
Unsupported Length - Minor Axis For Slenderness Check Ly (mm) 1000.00
Yield Stress fy (MPa) 240.00
Allowable Ratio For Interaction Check 1.00

Design Forces

Axial Load Fx (N ) 19231.93


Critical Loadcase No. 3

Details Of Calculation

Slenderness Checking

Lez (mm) 1000.00


Ley (mm) 1000.00
Lez / rz 70.93
Ley / ry 70.93
Actual Slenderness Ratio 70.93
Allowable Slenderness Ratio 180.00
Status SAFE

Check Against Axial Compression For Truss Member

Actual Compressive Stress fc (MPa)


=Fx / Ax 59.18

Calculation Of Allowable Compressive Stress :

Print Time/Date: 07/12/2018 20:09 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 334 of 617
Job No Sheet No Rev
BN/SS/-01 335
Part
Software licensed to BN
Job Title Design of Overhead Gantry Hoarding Truss - 30m Span Ref

By Biswajit Date06-Dec-18 Chd Biswajit


Client Suntony Signage File Final Gantry Truss-30m Date/Time
Span.std 07-Dec-2018 20:06

E (MPa) 200000.00
L/r 70.93
fcc (MPa)
2 2
=π E / λ 392.36
Allowable Compressive Stress fc_allowable (MPa)
1.4 1.4
=0.6fccfy / [(fcc) + (fy) ] 107.66
Interaction ratio
=fc / fc_allowable 0.55
Status SAFE

Print Time/Date: 07/12/2018 20:09 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 335 of 617
Job No Sheet No Rev
BN/SS/-01 336
Part
Software licensed to BN
Job Title Design of Overhead Gantry Hoarding Truss - 30m Span Ref

By Biswajit Date06-Dec-18 Chd Biswajit


Client Suntony Signage File Final Gantry Truss-30m Date/Time
Span.std 07-Dec-2018 20:06

Design Of Member No. 159 As Per IS:800

Input Parameters

Member Section PIP483L

2
Cross Sectional Area Ax (mm ) 414.00
Net section factor 1.00
2
Net Effective Sectional Area Anet (mm ) 414.00
rz (mm) 16.08
ry (mm) 16.08
Unsupported Length - Major Axis For Slenderness Check Lz (mm) 2000.00
Unsupported Length - Minor Axis For Slenderness Check Ly (mm) 2000.00
Yield Stress fy (MPa) 240.00
Allowable Ratio For Interaction Check 1.00

Design Forces

Axial Load Fx (N ) -4554.44


Critical Loadcase No. 3

Details Of Calculation

Slenderness Checking

Lez (mm) 2000.00


Ley (mm) 2000.00
Lez / rz 124.40
Ley / ry 124.40
Actual Slenderness Ratio 124.40
Allowable Slenderness Ratio 400.00
Status SAFE

Check Against Axial Tension For Truss Member

Actual Tensile Stress ft (MPa)


=Fx / Anet 11.00

Print Time/Date: 07/12/2018 20:09 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 336 of 617
Job No Sheet No Rev
BN/SS/-01 337
Part
Software licensed to BN
Job Title Design of Overhead Gantry Hoarding Truss - 30m Span Ref

By Biswajit Date06-Dec-18 Chd Biswajit


Client Suntony Signage File Final Gantry Truss-30m Date/Time
Span.std 07-Dec-2018 20:06

Allowable Tensile Stress ft_allowable (MPa)


=0.60fy 144.00
Interaction ratio
=ft / ft_allowable 0.08
Status SAFE

Print Time/Date: 07/12/2018 20:09 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 337 of 617
Job No Sheet No Rev
BN/SS/-01 338
Part
Software licensed to BN
Job Title Design of Overhead Gantry Hoarding Truss - 30m Span Ref

By Biswajit Date06-Dec-18 Chd Biswajit


Client Suntony Signage File Final Gantry Truss-30m Date/Time
Span.std 07-Dec-2018 20:06

Design Of Member No. 160 As Per IS:800

Input Parameters

Member Section PIP483L

2
Cross Sectional Area Ax (mm ) 414.00
rz (mm) 16.08
ry (mm) 16.08
Unsupported Length - Major Axis For Slenderness Check Lz (mm) 2000.00
Unsupported Length - Minor Axis For Slenderness Check Ly (mm) 2000.00
Yield Stress fy (MPa) 240.00
Allowable Ratio For Interaction Check 1.00

Design Forces

Axial Load Fx (N ) 7900.95


Critical Loadcase No. 3

Details Of Calculation

Slenderness Checking

Lez (mm) 2000.00


Ley (mm) 2000.00
Lez / rz 124.40
Ley / ry 124.40
Actual Slenderness Ratio 124.40
Allowable Slenderness Ratio 180.00
Status SAFE

Check Against Axial Compression For Truss Member

Actual Compressive Stress fc (MPa)


=Fx / Ax 19.08

Calculation Of Allowable Compressive Stress :

Print Time/Date: 07/12/2018 20:09 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 338 of 617
Job No Sheet No Rev
BN/SS/-01 339
Part
Software licensed to BN
Job Title Design of Overhead Gantry Hoarding Truss - 30m Span Ref

By Biswajit Date06-Dec-18 Chd Biswajit


Client Suntony Signage File Final Gantry Truss-30m Date/Time
Span.std 07-Dec-2018 20:06

E (MPa) 200000.00
L/r 124.40
fcc (MPa)
2 2
=π E / λ 127.54
Allowable Compressive Stress fc_allowable (MPa)
1.4 1.4
=0.6fccfy / [(fcc) + (fy) ] 59.79
Interaction ratio
=fc / fc_allowable 0.32
Status SAFE

Print Time/Date: 07/12/2018 20:09 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 339 of 617
Job No Sheet No Rev
BN/SS/-01 340
Part
Software licensed to BN
Job Title Design of Overhead Gantry Hoarding Truss - 30m Span Ref

By Biswajit Date06-Dec-18 Chd Biswajit


Client Suntony Signage File Final Gantry Truss-30m Date/Time
Span.std 07-Dec-2018 20:06

Design Of Member No. 161 As Per IS:800

Input Parameters

Member Section PIP424L

2
Cross Sectional Area Ax (mm ) 0.00
rz (mm) 14.10
ry (mm) 14.10
Unsupported Length - Major Axis For Slenderness Check Lz (mm) 1000.00
Unsupported Length - Minor Axis For Slenderness Check Ly (mm) 1000.00
Yield Stress fy (MPa) 0.00
Allowable Ratio For Interaction Check 1.00

Design Forces

Axial Load Fx (N ) 0.00


Critical Loadcase No. 0

Details Of Calculation

Slenderness Checking

Lez (mm) 1000.00


Ley (mm) 1000.00
Lez / rz 70.93
Ley / ry 70.93
Actual Slenderness Ratio 70.93
Allowable Slenderness Ratio 400.00
Status SAFE

Check Against Axial Compression For Truss Member

Actual Compressive Stress fc (MPa)


=Fx / Ax 0.00

Calculation Of Allowable Compressive Stress :

Print Time/Date: 07/12/2018 20:09 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 340 of 617
Job No Sheet No Rev
BN/SS/-01 341
Part
Software licensed to BN
Job Title Design of Overhead Gantry Hoarding Truss - 30m Span Ref

By Biswajit Date06-Dec-18 Chd Biswajit


Client Suntony Signage File Final Gantry Truss-30m Date/Time
Span.std 07-Dec-2018 20:06

E (MPa) 200000.00
L/r 70.93
fcc (MPa)
2 2
=π E / λ 392.36
Allowable Compressive Stress fc_allowable (MPa)
1.4 1.4
=0.6fccfy / [(fcc) + (fy) ] 0.00
Interaction ratio
=fc / fc_allowable 0.00
Status SAFE

Print Time/Date: 07/12/2018 20:09 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 341 of 617
Job No Sheet No Rev
BN/SS/-01 342
Part
Software licensed to BN
Job Title Design of Overhead Gantry Hoarding Truss - 30m Span Ref

By Biswajit Date06-Dec-18 Chd Biswajit


Client Suntony Signage File Final Gantry Truss-30m Date/Time
Span.std 07-Dec-2018 20:06

Design Of Member No. 162 As Per IS:800

Input Parameters

Member Section PIP603L

2
Cross Sectional Area Ax (mm ) 523.00
Net section factor 1.00
2
Net Effective Sectional Area Anet (mm ) 523.00
rz (mm) 20.32
ry (mm) 20.32
Unsupported Length - Major Axis For Slenderness Check Lz (mm) 1802.77
Unsupported Length - Minor Axis For Slenderness Check Ly (mm) 1802.77
Yield Stress fy (MPa) 240.00
Allowable Ratio For Interaction Check 1.00

Design Forces

Axial Load Fx (N ) -5428.16


Critical Loadcase No. 3

Details Of Calculation

Slenderness Checking

Lez (mm) 1802.77


Ley (mm) 1802.77
Lez / rz 88.71
Ley / ry 88.71
Actual Slenderness Ratio 88.71
Allowable Slenderness Ratio 400.00
Status SAFE

Check Against Axial Tension For Truss Member

Actual Tensile Stress ft (MPa)


=Fx / Anet 10.38

Print Time/Date: 07/12/2018 20:09 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 342 of 617
Job No Sheet No Rev
BN/SS/-01 343
Part
Software licensed to BN
Job Title Design of Overhead Gantry Hoarding Truss - 30m Span Ref

By Biswajit Date06-Dec-18 Chd Biswajit


Client Suntony Signage File Final Gantry Truss-30m Date/Time
Span.std 07-Dec-2018 20:06

Allowable Tensile Stress ft_allowable (MPa)


=0.60fy 144.00
Interaction ratio
=ft / ft_allowable 0.07
Status SAFE

Print Time/Date: 07/12/2018 20:09 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 343 of 617
Job No Sheet No Rev
BN/SS/-01 344
Part
Software licensed to BN
Job Title Design of Overhead Gantry Hoarding Truss - 30m Span Ref

By Biswajit Date06-Dec-18 Chd Biswajit


Client Suntony Signage File Final Gantry Truss-30m Date/Time
Span.std 07-Dec-2018 20:06

Design Of Member No. 163 As Per IS:800

Input Parameters

Member Section PIP483L

2
Cross Sectional Area Ax (mm ) 414.00
rz (mm) 16.08
ry (mm) 16.08
Unsupported Length - Major Axis For Slenderness Check Lz (mm) 2500.00
Unsupported Length - Minor Axis For Slenderness Check Ly (mm) 2500.00
Yield Stress fy (MPa) 240.00
Allowable Ratio For Interaction Check 1.00

Design Forces

Axial Load Fx (N ) 5962.88


Critical Loadcase No. 3

Details Of Calculation

Slenderness Checking

Lez (mm) 2500.00


Ley (mm) 2500.00
Lez / rz 155.51
Ley / ry 155.51
Actual Slenderness Ratio 155.51
Allowable Slenderness Ratio 180.00
Status SAFE

Check Against Axial Compression For Truss Member

Actual Compressive Stress fc (MPa)


=Fx / Ax 14.40

Calculation Of Allowable Compressive Stress :

Print Time/Date: 07/12/2018 20:09 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 344 of 617
Job No Sheet No Rev
BN/SS/-01 345
Part
Software licensed to BN
Job Title Design of Overhead Gantry Hoarding Truss - 30m Span Ref

By Biswajit Date06-Dec-18 Chd Biswajit


Client Suntony Signage File Final Gantry Truss-30m Date/Time
Span.std 07-Dec-2018 20:06

E (MPa) 200000.00
L/r 155.51
fcc (MPa)
2 2
=π E / λ 81.63
Allowable Compressive Stress fc_allowable (MPa)
1.4 1.4
=0.6fccfy / [(fcc) + (fy) ] 42.47
Interaction ratio
=fc / fc_allowable 0.34
Status SAFE

Print Time/Date: 07/12/2018 20:09 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 345 of 617
Job No Sheet No Rev
BN/SS/-01 346
Part
Software licensed to BN
Job Title Design of Overhead Gantry Hoarding Truss - 30m Span Ref

By Biswajit Date06-Dec-18 Chd Biswajit


Client Suntony Signage File Final Gantry Truss-30m Date/Time
Span.std 07-Dec-2018 20:06

Design Of Member No. 164 As Per IS:800

Input Parameters

Member Section PIP483L

2
Cross Sectional Area Ax (mm ) 414.00
Net section factor 1.00
2
Net Effective Sectional Area Anet (mm ) 414.00
rz (mm) 16.08
ry (mm) 16.08
Unsupported Length - Major Axis For Slenderness Check Lz (mm) 2500.00
Unsupported Length - Minor Axis For Slenderness Check Ly (mm) 2500.00
Yield Stress fy (MPa) 240.00
Allowable Ratio For Interaction Check 1.00

Design Forces

Axial Load Fx (N ) -23153.45


Critical Loadcase No. 3

Details Of Calculation

Slenderness Checking

Lez (mm) 2500.00


Ley (mm) 2500.00
Lez / rz 155.51
Ley / ry 155.51
Actual Slenderness Ratio 155.51
Allowable Slenderness Ratio 400.00
Status SAFE

Check Against Axial Tension For Truss Member

Actual Tensile Stress ft (MPa)


=Fx / Anet 55.93

Print Time/Date: 07/12/2018 20:09 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 346 of 617
Job No Sheet No Rev
BN/SS/-01 347
Part
Software licensed to BN
Job Title Design of Overhead Gantry Hoarding Truss - 30m Span Ref

By Biswajit Date06-Dec-18 Chd Biswajit


Client Suntony Signage File Final Gantry Truss-30m Date/Time
Span.std 07-Dec-2018 20:06

Allowable Tensile Stress ft_allowable (MPa)


=0.60fy 144.00
Interaction ratio
=ft / ft_allowable 0.39
Status SAFE

Print Time/Date: 07/12/2018 20:09 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 347 of 617
Job No Sheet No Rev
BN/SS/-01 348
Part
Software licensed to BN
Job Title Design of Overhead Gantry Hoarding Truss - 30m Span Ref

By Biswajit Date06-Dec-18 Chd Biswajit


Client Suntony Signage File Final Gantry Truss-30m Date/Time
Span.std 07-Dec-2018 20:06

Design Of Member No. 165 As Per IS:800

Input Parameters

Member Section PIP603L

2
Cross Sectional Area Ax (mm ) 523.00
rz (mm) 20.32
ry (mm) 20.32
Unsupported Length - Major Axis For Slenderness Check Lz (mm) 1802.77
Unsupported Length - Minor Axis For Slenderness Check Ly (mm) 1802.77
Yield Stress fy (MPa) 240.00
Allowable Ratio For Interaction Check 1.00

Design Forces

Axial Load Fx (N ) 12312.61


Critical Loadcase No. 3

Details Of Calculation

Slenderness Checking

Lez (mm) 1802.77


Ley (mm) 1802.77
Lez / rz 88.71
Ley / ry 88.71
Actual Slenderness Ratio 88.71
Allowable Slenderness Ratio 180.00
Status SAFE

Check Against Axial Compression For Truss Member

Actual Compressive Stress fc (MPa)


=Fx / Ax 23.54

Calculation Of Allowable Compressive Stress :

Print Time/Date: 07/12/2018 20:09 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 348 of 617
Job No Sheet No Rev
BN/SS/-01 349
Part
Software licensed to BN
Job Title Design of Overhead Gantry Hoarding Truss - 30m Span Ref

By Biswajit Date06-Dec-18 Chd Biswajit


Client Suntony Signage File Final Gantry Truss-30m Date/Time
Span.std 07-Dec-2018 20:06

E (MPa) 200000.00
L/r 88.71
fcc (MPa)
2 2
=π E / λ 250.84
Allowable Compressive Stress fc_allowable (MPa)
1.4 1.4
=0.6fccfy / [(fcc) + (fy) ] 89.69
Interaction ratio
=fc / fc_allowable 0.26
Status SAFE

Print Time/Date: 07/12/2018 20:09 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 349 of 617
Job No Sheet No Rev
BN/SS/-01 350
Part
Software licensed to BN
Job Title Design of Overhead Gantry Hoarding Truss - 30m Span Ref

By Biswajit Date06-Dec-18 Chd Biswajit


Client Suntony Signage File Final Gantry Truss-30m Date/Time
Span.std 07-Dec-2018 20:06

Design Of Member No. 166 As Per IS:800

Input Parameters

Member Section PIP424L

2
Cross Sectional Area Ax (mm ) 325.00
Net section factor 1.00
2
Net Effective Sectional Area Anet (mm ) 325.00
rz (mm) 14.10
ry (mm) 14.10
Unsupported Length - Major Axis For Slenderness Check Lz (mm) 1000.00
Unsupported Length - Minor Axis For Slenderness Check Ly (mm) 1000.00
Yield Stress fy (MPa) 240.00
Allowable Ratio For Interaction Check 1.00

Design Forces

Axial Load Fx (N ) -5405.80


Critical Loadcase No. 3

Details Of Calculation

Slenderness Checking

Lez (mm) 1000.00


Ley (mm) 1000.00
Lez / rz 70.93
Ley / ry 70.93
Actual Slenderness Ratio 70.93
Allowable Slenderness Ratio 400.00
Status SAFE

Check Against Axial Tension For Truss Member

Actual Tensile Stress ft (MPa)


=Fx / Anet 16.63

Print Time/Date: 07/12/2018 20:09 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 350 of 617
Job No Sheet No Rev
BN/SS/-01 351
Part
Software licensed to BN
Job Title Design of Overhead Gantry Hoarding Truss - 30m Span Ref

By Biswajit Date06-Dec-18 Chd Biswajit


Client Suntony Signage File Final Gantry Truss-30m Date/Time
Span.std 07-Dec-2018 20:06

Allowable Tensile Stress ft_allowable (MPa)


=0.60fy 144.00
Interaction ratio
=ft / ft_allowable 0.12
Status SAFE

Print Time/Date: 07/12/2018 20:09 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 351 of 617
Job No Sheet No Rev
BN/SS/-01 352
Part
Software licensed to BN
Job Title Design of Overhead Gantry Hoarding Truss - 30m Span Ref

By Biswajit Date06-Dec-18 Chd Biswajit


Client Suntony Signage File Final Gantry Truss-30m Date/Time
Span.std 07-Dec-2018 20:06

Design Of Member No. 167 As Per IS:800

Input Parameters

Member Section PIP1016L

2
Cross Sectional Area Ax (mm ) 1110.00
rz (mm) 34.62
ry (mm) 34.62
Unsupported Length - Major Axis For Slenderness Check Lz (mm) 2000.00
Unsupported Length - Minor Axis For Slenderness Check Ly (mm) 2000.00
Yield Stress fy (MPa) 240.00
Allowable Ratio For Interaction Check 1.00

Design Forces

Axial Load Fx (N ) 297.35


Critical Loadcase No. 3

Details Of Calculation

Slenderness Checking

Lez (mm) 2000.00


Ley (mm) 2000.00
Lez / rz 57.78
Ley / ry 57.78
Actual Slenderness Ratio 57.78
Allowable Slenderness Ratio 180.00
Status SAFE

Check Against Axial Compression For Truss Member

Actual Compressive Stress fc (MPa)


=Fx / Ax 0.27

Calculation Of Allowable Compressive Stress :

Print Time/Date: 07/12/2018 20:09 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 352 of 617
Job No Sheet No Rev
BN/SS/-01 353
Part
Software licensed to BN
Job Title Design of Overhead Gantry Hoarding Truss - 30m Span Ref

By Biswajit Date06-Dec-18 Chd Biswajit


Client Suntony Signage File Final Gantry Truss-30m Date/Time
Span.std 07-Dec-2018 20:06

E (MPa) 200000.00
L/r 57.78
fcc (MPa)
2 2
=π E / λ 591.29
Allowable Compressive Stress fc_allowable (MPa)
1.4 1.4
=0.6fccfy / [(fcc) + (fy) ] 120.51
Interaction ratio
=fc / fc_allowable 0.00
Status SAFE

Print Time/Date: 07/12/2018 20:09 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 353 of 617
Job No Sheet No Rev
BN/SS/-01 354
Part
Software licensed to BN
Job Title Design of Overhead Gantry Hoarding Truss - 30m Span Ref

By Biswajit Date06-Dec-18 Chd Biswajit


Client Suntony Signage File Final Gantry Truss-30m Date/Time
Span.std 07-Dec-2018 20:06

Design Of Member No. 168 As Per IS:800

Input Parameters

Member Section PIP483L

2
Cross Sectional Area Ax (mm ) 414.00
rz (mm) 16.08
ry (mm) 16.08
Unsupported Length - Major Axis For Slenderness Check Lz (mm) 2236.06
Unsupported Length - Minor Axis For Slenderness Check Ly (mm) 2236.06
Yield Stress fy (MPa) 240.00
Allowable Ratio For Interaction Check 1.00

Design Forces

Axial Load Fx (N ) 18853.93


Critical Loadcase No. 3

Details Of Calculation

Slenderness Checking

Lez (mm) 2236.06


Ley (mm) 2236.06
Lez / rz 139.09
Ley / ry 139.09
Actual Slenderness Ratio 139.09
Allowable Slenderness Ratio 180.00
Status SAFE

Check Against Axial Compression For Truss Member

Actual Compressive Stress fc (MPa)


=Fx / Ax 45.54

Calculation Of Allowable Compressive Stress :

Print Time/Date: 07/12/2018 20:09 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 354 of 617
Job No Sheet No Rev
BN/SS/-01 355
Part
Software licensed to BN
Job Title Design of Overhead Gantry Hoarding Truss - 30m Span Ref

By Biswajit Date06-Dec-18 Chd Biswajit


Client Suntony Signage File Final Gantry Truss-30m Date/Time
Span.std 07-Dec-2018 20:06

E (MPa) 200000.00
L/r 139.09
fcc (MPa)
2 2
=π E / λ 102.03
Allowable Compressive Stress fc_allowable (MPa)
1.4 1.4
=0.6fccfy / [(fcc) + (fy) ] 50.70
Interaction ratio
=fc / fc_allowable 0.90
Status SAFE

Print Time/Date: 07/12/2018 20:09 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 355 of 617
Job No Sheet No Rev
BN/SS/-01 356
Part
Software licensed to BN
Job Title Design of Overhead Gantry Hoarding Truss - 30m Span Ref

By Biswajit Date06-Dec-18 Chd Biswajit


Client Suntony Signage File Final Gantry Truss-30m Date/Time
Span.std 07-Dec-2018 20:06

Design Of Member No. 169 As Per IS:800

Input Parameters

Member Section PIP1016L

2
Cross Sectional Area Ax (mm ) 1110.00
Net section factor 1.00
2
Net Effective Sectional Area Anet (mm ) 1110.00
rz (mm) 34.62
ry (mm) 34.62
Unsupported Length - Major Axis For Slenderness Check Lz (mm) 2000.00
Unsupported Length - Minor Axis For Slenderness Check Ly (mm) 2000.00
Yield Stress fy (MPa) 240.00
Allowable Ratio For Interaction Check 1.00

Design Forces

Axial Load Fx (N ) -16716.01


Critical Loadcase No. 3

Details Of Calculation

Slenderness Checking

Lez (mm) 2000.00


Ley (mm) 2000.00
Lez / rz 57.78
Ley / ry 57.78
Actual Slenderness Ratio 57.78
Allowable Slenderness Ratio 400.00
Status SAFE

Check Against Axial Tension For Truss Member

Actual Tensile Stress ft (MPa)


=Fx / Anet 15.06

Print Time/Date: 07/12/2018 20:09 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 356 of 617
Job No Sheet No Rev
BN/SS/-01 357
Part
Software licensed to BN
Job Title Design of Overhead Gantry Hoarding Truss - 30m Span Ref

By Biswajit Date06-Dec-18 Chd Biswajit


Client Suntony Signage File Final Gantry Truss-30m Date/Time
Span.std 07-Dec-2018 20:06

Allowable Tensile Stress ft_allowable (MPa)


=0.60fy 144.00
Interaction ratio
=ft / ft_allowable 0.10
Status SAFE

Print Time/Date: 07/12/2018 20:09 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 357 of 617
Job No Sheet No Rev
BN/SS/-01 358
Part
Software licensed to BN
Job Title Design of Overhead Gantry Hoarding Truss - 30m Span Ref

By Biswajit Date06-Dec-18 Chd Biswajit


Client Suntony Signage File Final Gantry Truss-30m Date/Time
Span.std 07-Dec-2018 20:06

Design Of Member No. 170 As Per IS:800

Input Parameters

Member Section PIP424L

2
Cross Sectional Area Ax (mm ) 325.00
Net section factor 1.00
2
Net Effective Sectional Area Anet (mm ) 325.00
rz (mm) 14.10
ry (mm) 14.10
Unsupported Length - Major Axis For Slenderness Check Lz (mm) 1000.00
Unsupported Length - Minor Axis For Slenderness Check Ly (mm) 1000.00
Yield Stress fy (MPa) 240.00
Allowable Ratio For Interaction Check 1.00

Design Forces

Axial Load Fx (N ) -6829.80


Critical Loadcase No. 3

Details Of Calculation

Slenderness Checking

Lez (mm) 1000.00


Ley (mm) 1000.00
Lez / rz 70.93
Ley / ry 70.93
Actual Slenderness Ratio 70.93
Allowable Slenderness Ratio 400.00
Status SAFE

Check Against Axial Tension For Truss Member

Actual Tensile Stress ft (MPa)


=Fx / Anet 21.01

Print Time/Date: 07/12/2018 20:09 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 358 of 617
Job No Sheet No Rev
BN/SS/-01 359
Part
Software licensed to BN
Job Title Design of Overhead Gantry Hoarding Truss - 30m Span Ref

By Biswajit Date06-Dec-18 Chd Biswajit


Client Suntony Signage File Final Gantry Truss-30m Date/Time
Span.std 07-Dec-2018 20:06

Allowable Tensile Stress ft_allowable (MPa)


=0.60fy 144.00
Interaction ratio
=ft / ft_allowable 0.15
Status SAFE

Print Time/Date: 07/12/2018 20:09 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 359 of 617
Job No Sheet No Rev
BN/SS/-01 360
Part
Software licensed to BN
Job Title Design of Overhead Gantry Hoarding Truss - 30m Span Ref

By Biswajit Date06-Dec-18 Chd Biswajit


Client Suntony Signage File Final Gantry Truss-30m Date/Time
Span.std 07-Dec-2018 20:06

Design Of Member No. 171 As Per IS:800

Input Parameters

Member Section PIP483L

2
Cross Sectional Area Ax (mm ) 414.00
rz (mm) 16.08
ry (mm) 16.08
Unsupported Length - Major Axis For Slenderness Check Lz (mm) 2236.06
Unsupported Length - Minor Axis For Slenderness Check Ly (mm) 2236.06
Yield Stress fy (MPa) 240.00
Allowable Ratio For Interaction Check 1.00

Design Forces

Axial Load Fx (N ) 24762.78


Critical Loadcase No. 3

Details Of Calculation

Slenderness Checking

Lez (mm) 2236.06


Ley (mm) 2236.06
Lez / rz 139.09
Ley / ry 139.09
Actual Slenderness Ratio 139.09
Allowable Slenderness Ratio 180.00
Status SAFE

Check Against Axial Compression For Truss Member

Actual Compressive Stress fc (MPa)


=Fx / Ax 59.81

Calculation Of Allowable Compressive Stress :

Print Time/Date: 07/12/2018 20:09 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 360 of 617
Job No Sheet No Rev
BN/SS/-01 361
Part
Software licensed to BN
Job Title Design of Overhead Gantry Hoarding Truss - 30m Span Ref

By Biswajit Date06-Dec-18 Chd Biswajit


Client Suntony Signage File Final Gantry Truss-30m Date/Time
Span.std 07-Dec-2018 20:06

E (MPa) 200000.00
L/r 139.09
fcc (MPa)
2 2
=π E / λ 102.03
Allowable Compressive Stress fc_allowable (MPa)
1.4 1.4
=0.6fccfy / [(fcc) + (fy) ] 50.70
Interaction ratio
=fc / fc_allowable 1.18
Status UNSAFE

Print Time/Date: 07/12/2018 20:09 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 361 of 617
Job No Sheet No Rev
BN/SS/-01 362
Part
Software licensed to BN
Job Title Design of Overhead Gantry Hoarding Truss - 30m Span Ref

By Biswajit Date06-Dec-18 Chd Biswajit


Client Suntony Signage File Final Gantry Truss-30m Date/Time
Span.std 07-Dec-2018 20:06

Design Of Member No. 172 As Per IS:800

Input Parameters

Member Section PIP483L

2
Cross Sectional Area Ax (mm ) 414.00
rz (mm) 16.08
ry (mm) 16.08
Unsupported Length - Major Axis For Slenderness Check Lz (mm) 2236.06
Unsupported Length - Minor Axis For Slenderness Check Ly (mm) 2236.06
Yield Stress fy (MPa) 240.00
Allowable Ratio For Interaction Check 1.00

Design Forces

Axial Load Fx (N ) 4246.39


Critical Loadcase No. 3

Details Of Calculation

Slenderness Checking

Lez (mm) 2236.06


Ley (mm) 2236.06
Lez / rz 139.09
Ley / ry 139.09
Actual Slenderness Ratio 139.09
Allowable Slenderness Ratio 180.00
Status SAFE

Check Against Axial Compression For Truss Member

Actual Compressive Stress fc (MPa)


=Fx / Ax 10.26

Calculation Of Allowable Compressive Stress :

Print Time/Date: 07/12/2018 20:09 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 362 of 617
Job No Sheet No Rev
BN/SS/-01 363
Part
Software licensed to BN
Job Title Design of Overhead Gantry Hoarding Truss - 30m Span Ref

By Biswajit Date06-Dec-18 Chd Biswajit


Client Suntony Signage File Final Gantry Truss-30m Date/Time
Span.std 07-Dec-2018 20:06

E (MPa) 200000.00
L/r 139.09
fcc (MPa)
2 2
=π E / λ 102.03
Allowable Compressive Stress fc_allowable (MPa)
1.4 1.4
=0.6fccfy / [(fcc) + (fy) ] 50.70
Interaction ratio
=fc / fc_allowable 0.20
Status SAFE

Print Time/Date: 07/12/2018 20:09 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 363 of 617
Job No Sheet No Rev
BN/SS/-01 364
Part
Software licensed to BN
Job Title Design of Overhead Gantry Hoarding Truss - 30m Span Ref

By Biswajit Date06-Dec-18 Chd Biswajit


Client Suntony Signage File Final Gantry Truss-30m Date/Time
Span.std 07-Dec-2018 20:06

Design Of Member No. 173 As Per IS:800

Input Parameters

Member Section PIP483L

2
Cross Sectional Area Ax (mm ) 414.00
rz (mm) 16.08
ry (mm) 16.08
Unsupported Length - Major Axis For Slenderness Check Lz (mm) 2236.06
Unsupported Length - Minor Axis For Slenderness Check Ly (mm) 2236.06
Yield Stress fy (MPa) 240.00
Allowable Ratio For Interaction Check 1.00

Design Forces

Axial Load Fx (N ) 1269.75


Critical Loadcase No. 3

Details Of Calculation

Slenderness Checking

Lez (mm) 2236.06


Ley (mm) 2236.06
Lez / rz 139.09
Ley / ry 139.09
Actual Slenderness Ratio 139.09
Allowable Slenderness Ratio 180.00
Status SAFE

Check Against Axial Compression For Truss Member

Actual Compressive Stress fc (MPa)


=Fx / Ax 3.07

Calculation Of Allowable Compressive Stress :

Print Time/Date: 07/12/2018 20:09 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 364 of 617
Job No Sheet No Rev
BN/SS/-01 365
Part
Software licensed to BN
Job Title Design of Overhead Gantry Hoarding Truss - 30m Span Ref

By Biswajit Date06-Dec-18 Chd Biswajit


Client Suntony Signage File Final Gantry Truss-30m Date/Time
Span.std 07-Dec-2018 20:06

E (MPa) 200000.00
L/r 139.09
fcc (MPa)
2 2
=π E / λ 102.03
Allowable Compressive Stress fc_allowable (MPa)
1.4 1.4
=0.6fccfy / [(fcc) + (fy) ] 50.70
Interaction ratio
=fc / fc_allowable 0.06
Status SAFE

Print Time/Date: 07/12/2018 20:09 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 365 of 617
Job No Sheet No Rev
BN/SS/-01 366
Part
Software licensed to BN
Job Title Design of Overhead Gantry Hoarding Truss - 30m Span Ref

By Biswajit Date06-Dec-18 Chd Biswajit


Client Suntony Signage File Final Gantry Truss-30m Date/Time
Span.std 07-Dec-2018 20:06

Design Of Member No. 174 As Per IS:800

Input Parameters

Member Section PIP483L

2
Cross Sectional Area Ax (mm ) 414.00
rz (mm) 16.08
ry (mm) 16.08
Unsupported Length - Major Axis For Slenderness Check Lz (mm) 2236.06
Unsupported Length - Minor Axis For Slenderness Check Ly (mm) 2236.06
Yield Stress fy (MPa) 240.00
Allowable Ratio For Interaction Check 1.00

Design Forces

Axial Load Fx (N ) 1026.42


Critical Loadcase No. 3

Details Of Calculation

Slenderness Checking

Lez (mm) 2236.06


Ley (mm) 2236.06
Lez / rz 139.09
Ley / ry 139.09
Actual Slenderness Ratio 139.09
Allowable Slenderness Ratio 180.00
Status SAFE

Check Against Axial Compression For Truss Member

Actual Compressive Stress fc (MPa)


=Fx / Ax 2.48

Calculation Of Allowable Compressive Stress :

Print Time/Date: 07/12/2018 20:09 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 366 of 617
Job No Sheet No Rev
BN/SS/-01 367
Part
Software licensed to BN
Job Title Design of Overhead Gantry Hoarding Truss - 30m Span Ref

By Biswajit Date06-Dec-18 Chd Biswajit


Client Suntony Signage File Final Gantry Truss-30m Date/Time
Span.std 07-Dec-2018 20:06

E (MPa) 200000.00
L/r 139.09
fcc (MPa)
2 2
=π E / λ 102.03
Allowable Compressive Stress fc_allowable (MPa)
1.4 1.4
=0.6fccfy / [(fcc) + (fy) ] 50.70
Interaction ratio
=fc / fc_allowable 0.05
Status SAFE

Print Time/Date: 07/12/2018 20:09 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 367 of 617
Job No Sheet No Rev
BN/SS/-01 368
Part
Software licensed to BN
Job Title Design of Overhead Gantry Hoarding Truss - 30m Span Ref

By Biswajit Date06-Dec-18 Chd Biswajit


Client Suntony Signage File Final Gantry Truss-30m Date/Time
Span.std 07-Dec-2018 20:06

Design Of Member No. 175 As Per IS:800

Input Parameters

Member Section PIP483L

2
Cross Sectional Area Ax (mm ) 414.00
Net section factor 1.00
2
Net Effective Sectional Area Anet (mm ) 414.00
rz (mm) 16.08
ry (mm) 16.08
Unsupported Length - Major Axis For Slenderness Check Lz (mm) 2236.06
Unsupported Length - Minor Axis For Slenderness Check Ly (mm) 2236.06
Yield Stress fy (MPa) 240.00
Allowable Ratio For Interaction Check 1.00

Design Forces

Axial Load Fx (N ) -264.34


Critical Loadcase No. 3

Details Of Calculation

Slenderness Checking

Lez (mm) 2236.06


Ley (mm) 2236.06
Lez / rz 139.09
Ley / ry 139.09
Actual Slenderness Ratio 139.09
Allowable Slenderness Ratio 400.00
Status SAFE

Check Against Axial Tension For Truss Member

Actual Tensile Stress ft (MPa)


=Fx / Anet 0.64

Print Time/Date: 07/12/2018 20:09 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 368 of 617
Job No Sheet No Rev
BN/SS/-01 369
Part
Software licensed to BN
Job Title Design of Overhead Gantry Hoarding Truss - 30m Span Ref

By Biswajit Date06-Dec-18 Chd Biswajit


Client Suntony Signage File Final Gantry Truss-30m Date/Time
Span.std 07-Dec-2018 20:06

Allowable Tensile Stress ft_allowable (MPa)


=0.60fy 144.00
Interaction ratio
=ft / ft_allowable 0.00
Status SAFE

Print Time/Date: 07/12/2018 20:09 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 369 of 617
Job No Sheet No Rev
BN/SS/-01 370
Part
Software licensed to BN
Job Title Design of Overhead Gantry Hoarding Truss - 30m Span Ref

By Biswajit Date06-Dec-18 Chd Biswajit


Client Suntony Signage File Final Gantry Truss-30m Date/Time
Span.std 07-Dec-2018 20:06

Design Of Member No. 176 As Per IS:800

Input Parameters

Member Section PIP483L

2
Cross Sectional Area Ax (mm ) 414.00
rz (mm) 16.08
ry (mm) 16.08
Unsupported Length - Major Axis For Slenderness Check Lz (mm) 2236.06
Unsupported Length - Minor Axis For Slenderness Check Ly (mm) 2236.06
Yield Stress fy (MPa) 240.00
Allowable Ratio For Interaction Check 1.00

Design Forces

Axial Load Fx (N ) 852.84


Critical Loadcase No. 3

Details Of Calculation

Slenderness Checking

Lez (mm) 2236.06


Ley (mm) 2236.06
Lez / rz 139.09
Ley / ry 139.09
Actual Slenderness Ratio 139.09
Allowable Slenderness Ratio 180.00
Status SAFE

Check Against Axial Compression For Truss Member

Actual Compressive Stress fc (MPa)


=Fx / Ax 2.06

Calculation Of Allowable Compressive Stress :

Print Time/Date: 07/12/2018 20:09 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 370 of 617
Job No Sheet No Rev
BN/SS/-01 371
Part
Software licensed to BN
Job Title Design of Overhead Gantry Hoarding Truss - 30m Span Ref

By Biswajit Date06-Dec-18 Chd Biswajit


Client Suntony Signage File Final Gantry Truss-30m Date/Time
Span.std 07-Dec-2018 20:06

E (MPa) 200000.00
L/r 139.09
fcc (MPa)
2 2
=π E / λ 102.03
Allowable Compressive Stress fc_allowable (MPa)
1.4 1.4
=0.6fccfy / [(fcc) + (fy) ] 50.70
Interaction ratio
=fc / fc_allowable 0.04
Status SAFE

Print Time/Date: 07/12/2018 20:09 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 371 of 617
Job No Sheet No Rev
BN/SS/-01 372
Part
Software licensed to BN
Job Title Design of Overhead Gantry Hoarding Truss - 30m Span Ref

By Biswajit Date06-Dec-18 Chd Biswajit


Client Suntony Signage File Final Gantry Truss-30m Date/Time
Span.std 07-Dec-2018 20:06

Design Of Member No. 177 As Per IS:800

Input Parameters

Member Section PIP483L

2
Cross Sectional Area Ax (mm ) 414.00
Net section factor 1.00
2
Net Effective Sectional Area Anet (mm ) 414.00
rz (mm) 16.08
ry (mm) 16.08
Unsupported Length - Major Axis For Slenderness Check Lz (mm) 2236.06
Unsupported Length - Minor Axis For Slenderness Check Ly (mm) 2236.06
Yield Stress fy (MPa) 240.00
Allowable Ratio For Interaction Check 1.00

Design Forces

Axial Load Fx (N ) -710.15


Critical Loadcase No. 3

Details Of Calculation

Slenderness Checking

Lez (mm) 2236.06


Ley (mm) 2236.06
Lez / rz 139.09
Ley / ry 139.09
Actual Slenderness Ratio 139.09
Allowable Slenderness Ratio 400.00
Status SAFE

Check Against Axial Tension For Truss Member

Actual Tensile Stress ft (MPa)


=Fx / Anet 1.72

Print Time/Date: 07/12/2018 20:09 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 372 of 617
Job No Sheet No Rev
BN/SS/-01 373
Part
Software licensed to BN
Job Title Design of Overhead Gantry Hoarding Truss - 30m Span Ref

By Biswajit Date06-Dec-18 Chd Biswajit


Client Suntony Signage File Final Gantry Truss-30m Date/Time
Span.std 07-Dec-2018 20:06

Allowable Tensile Stress ft_allowable (MPa)


=0.60fy 144.00
Interaction ratio
=ft / ft_allowable 0.01
Status SAFE

Print Time/Date: 07/12/2018 20:09 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 373 of 617
Job No Sheet No Rev
BN/SS/-01 374
Part
Software licensed to BN
Job Title Design of Overhead Gantry Hoarding Truss - 30m Span Ref

By Biswajit Date06-Dec-18 Chd Biswajit


Client Suntony Signage File Final Gantry Truss-30m Date/Time
Span.std 07-Dec-2018 20:06

Design Of Member No. 178 As Per IS:800

Input Parameters

Member Section PIP483L

2
Cross Sectional Area Ax (mm ) 414.00
rz (mm) 16.08
ry (mm) 16.08
Unsupported Length - Major Axis For Slenderness Check Lz (mm) 2236.06
Unsupported Length - Minor Axis For Slenderness Check Ly (mm) 2236.06
Yield Stress fy (MPa) 240.00
Allowable Ratio For Interaction Check 1.00

Design Forces

Axial Load Fx (N ) 911.84


Critical Loadcase No. 3

Details Of Calculation

Slenderness Checking

Lez (mm) 2236.06


Ley (mm) 2236.06
Lez / rz 139.09
Ley / ry 139.09
Actual Slenderness Ratio 139.09
Allowable Slenderness Ratio 180.00
Status SAFE

Check Against Axial Compression For Truss Member

Actual Compressive Stress fc (MPa)


=Fx / Ax 2.20

Calculation Of Allowable Compressive Stress :

Print Time/Date: 07/12/2018 20:09 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 374 of 617
Job No Sheet No Rev
BN/SS/-01 375
Part
Software licensed to BN
Job Title Design of Overhead Gantry Hoarding Truss - 30m Span Ref

By Biswajit Date06-Dec-18 Chd Biswajit


Client Suntony Signage File Final Gantry Truss-30m Date/Time
Span.std 07-Dec-2018 20:06

E (MPa) 200000.00
L/r 139.09
fcc (MPa)
2 2
=π E / λ 102.03
Allowable Compressive Stress fc_allowable (MPa)
1.4 1.4
=0.6fccfy / [(fcc) + (fy) ] 50.70
Interaction ratio
=fc / fc_allowable 0.04
Status SAFE

Print Time/Date: 07/12/2018 20:09 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 375 of 617
Job No Sheet No Rev
BN/SS/-01 376
Part
Software licensed to BN
Job Title Design of Overhead Gantry Hoarding Truss - 30m Span Ref

By Biswajit Date06-Dec-18 Chd Biswajit


Client Suntony Signage File Final Gantry Truss-30m Date/Time
Span.std 07-Dec-2018 20:06

Design Of Member No. 179 As Per IS:800

Input Parameters

Member Section PIP483L

2
Cross Sectional Area Ax (mm ) 414.00
Net section factor 1.00
2
Net Effective Sectional Area Anet (mm ) 414.00
rz (mm) 16.08
ry (mm) 16.08
Unsupported Length - Major Axis For Slenderness Check Lz (mm) 2236.06
Unsupported Length - Minor Axis For Slenderness Check Ly (mm) 2236.06
Yield Stress fy (MPa) 240.00
Allowable Ratio For Interaction Check 1.00

Design Forces

Axial Load Fx (N ) -876.41


Critical Loadcase No. 3

Details Of Calculation

Slenderness Checking

Lez (mm) 2236.06


Ley (mm) 2236.06
Lez / rz 139.09
Ley / ry 139.09
Actual Slenderness Ratio 139.09
Allowable Slenderness Ratio 400.00
Status SAFE

Check Against Axial Tension For Truss Member

Actual Tensile Stress ft (MPa)


=Fx / Anet 2.12

Print Time/Date: 07/12/2018 20:09 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 376 of 617
Job No Sheet No Rev
BN/SS/-01 377
Part
Software licensed to BN
Job Title Design of Overhead Gantry Hoarding Truss - 30m Span Ref

By Biswajit Date06-Dec-18 Chd Biswajit


Client Suntony Signage File Final Gantry Truss-30m Date/Time
Span.std 07-Dec-2018 20:06

Allowable Tensile Stress ft_allowable (MPa)


=0.60fy 144.00
Interaction ratio
=ft / ft_allowable 0.01
Status SAFE

Print Time/Date: 07/12/2018 20:09 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 377 of 617
Job No Sheet No Rev
BN/SS/-01 378
Part
Software licensed to BN
Job Title Design of Overhead Gantry Hoarding Truss - 30m Span Ref

By Biswajit Date06-Dec-18 Chd Biswajit


Client Suntony Signage File Final Gantry Truss-30m Date/Time
Span.std 07-Dec-2018 20:06

Design Of Member No. 180 As Per IS:800

Input Parameters

Member Section PIP483L

2
Cross Sectional Area Ax (mm ) 414.00
rz (mm) 16.08
ry (mm) 16.08
Unsupported Length - Major Axis For Slenderness Check Lz (mm) 2236.06
Unsupported Length - Minor Axis For Slenderness Check Ly (mm) 2236.06
Yield Stress fy (MPa) 240.00
Allowable Ratio For Interaction Check 1.00

Design Forces

Axial Load Fx (N ) 942.90


Critical Loadcase No. 3

Details Of Calculation

Slenderness Checking

Lez (mm) 2236.06


Ley (mm) 2236.06
Lez / rz 139.09
Ley / ry 139.09
Actual Slenderness Ratio 139.09
Allowable Slenderness Ratio 180.00
Status SAFE

Check Against Axial Compression For Truss Member

Actual Compressive Stress fc (MPa)


=Fx / Ax 2.28

Calculation Of Allowable Compressive Stress :

Print Time/Date: 07/12/2018 20:09 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 378 of 617
Job No Sheet No Rev
BN/SS/-01 379
Part
Software licensed to BN
Job Title Design of Overhead Gantry Hoarding Truss - 30m Span Ref

By Biswajit Date06-Dec-18 Chd Biswajit


Client Suntony Signage File Final Gantry Truss-30m Date/Time
Span.std 07-Dec-2018 20:06

E (MPa) 200000.00
L/r 139.09
fcc (MPa)
2 2
=π E / λ 102.03
Allowable Compressive Stress fc_allowable (MPa)
1.4 1.4
=0.6fccfy / [(fcc) + (fy) ] 50.70
Interaction ratio
=fc / fc_allowable 0.04
Status SAFE

Print Time/Date: 07/12/2018 20:09 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 379 of 617
Job No Sheet No Rev
BN/SS/-01 380
Part
Software licensed to BN
Job Title Design of Overhead Gantry Hoarding Truss - 30m Span Ref

By Biswajit Date06-Dec-18 Chd Biswajit


Client Suntony Signage File Final Gantry Truss-30m Date/Time
Span.std 07-Dec-2018 20:06

Design Of Member No. 181 As Per IS:800

Input Parameters

Member Section PIP483L

2
Cross Sectional Area Ax (mm ) 414.00
Net section factor 1.00
2
Net Effective Sectional Area Anet (mm ) 414.00
rz (mm) 16.08
ry (mm) 16.08
Unsupported Length - Major Axis For Slenderness Check Lz (mm) 2236.06
Unsupported Length - Minor Axis For Slenderness Check Ly (mm) 2236.06
Yield Stress fy (MPa) 240.00
Allowable Ratio For Interaction Check 1.00

Design Forces

Axial Load Fx (N ) -872.96


Critical Loadcase No. 3

Details Of Calculation

Slenderness Checking

Lez (mm) 2236.06


Ley (mm) 2236.06
Lez / rz 139.09
Ley / ry 139.09
Actual Slenderness Ratio 139.09
Allowable Slenderness Ratio 400.00
Status SAFE

Check Against Axial Tension For Truss Member

Actual Tensile Stress ft (MPa)


=Fx / Anet 2.11

Print Time/Date: 07/12/2018 20:09 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 380 of 617
Job No Sheet No Rev
BN/SS/-01 381
Part
Software licensed to BN
Job Title Design of Overhead Gantry Hoarding Truss - 30m Span Ref

By Biswajit Date06-Dec-18 Chd Biswajit


Client Suntony Signage File Final Gantry Truss-30m Date/Time
Span.std 07-Dec-2018 20:06

Allowable Tensile Stress ft_allowable (MPa)


=0.60fy 144.00
Interaction ratio
=ft / ft_allowable 0.01
Status SAFE

Print Time/Date: 07/12/2018 20:09 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 381 of 617
Job No Sheet No Rev
BN/SS/-01 382
Part
Software licensed to BN
Job Title Design of Overhead Gantry Hoarding Truss - 30m Span Ref

By Biswajit Date06-Dec-18 Chd Biswajit


Client Suntony Signage File Final Gantry Truss-30m Date/Time
Span.std 07-Dec-2018 20:06

Design Of Member No. 182 As Per IS:800

Input Parameters

Member Section PIP483L

2
Cross Sectional Area Ax (mm ) 414.00
rz (mm) 16.08
ry (mm) 16.08
Unsupported Length - Major Axis For Slenderness Check Lz (mm) 2236.06
Unsupported Length - Minor Axis For Slenderness Check Ly (mm) 2236.06
Yield Stress fy (MPa) 240.00
Allowable Ratio For Interaction Check 1.00

Design Forces

Axial Load Fx (N ) 902.78


Critical Loadcase No. 3

Details Of Calculation

Slenderness Checking

Lez (mm) 2236.06


Ley (mm) 2236.06
Lez / rz 139.09
Ley / ry 139.09
Actual Slenderness Ratio 139.09
Allowable Slenderness Ratio 180.00
Status SAFE

Check Against Axial Compression For Truss Member

Actual Compressive Stress fc (MPa)


=Fx / Ax 2.18

Calculation Of Allowable Compressive Stress :

Print Time/Date: 07/12/2018 20:09 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 382 of 617
Job No Sheet No Rev
BN/SS/-01 383
Part
Software licensed to BN
Job Title Design of Overhead Gantry Hoarding Truss - 30m Span Ref

By Biswajit Date06-Dec-18 Chd Biswajit


Client Suntony Signage File Final Gantry Truss-30m Date/Time
Span.std 07-Dec-2018 20:06

E (MPa) 200000.00
L/r 139.09
fcc (MPa)
2 2
=π E / λ 102.03
Allowable Compressive Stress fc_allowable (MPa)
1.4 1.4
=0.6fccfy / [(fcc) + (fy) ] 50.70
Interaction ratio
=fc / fc_allowable 0.04
Status SAFE

Print Time/Date: 07/12/2018 20:09 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 383 of 617
Job No Sheet No Rev
BN/SS/-01 384
Part
Software licensed to BN
Job Title Design of Overhead Gantry Hoarding Truss - 30m Span Ref

By Biswajit Date06-Dec-18 Chd Biswajit


Client Suntony Signage File Final Gantry Truss-30m Date/Time
Span.std 07-Dec-2018 20:06

Design Of Member No. 183 As Per IS:800

Input Parameters

Member Section PIP483L

2
Cross Sectional Area Ax (mm ) 414.00
Net section factor 1.00
2
Net Effective Sectional Area Anet (mm ) 414.00
rz (mm) 16.08
ry (mm) 16.08
Unsupported Length - Major Axis For Slenderness Check Lz (mm) 2236.06
Unsupported Length - Minor Axis For Slenderness Check Ly (mm) 2236.06
Yield Stress fy (MPa) 240.00
Allowable Ratio For Interaction Check 1.00

Design Forces

Axial Load Fx (N ) -701.13


Critical Loadcase No. 3

Details Of Calculation

Slenderness Checking

Lez (mm) 2236.06


Ley (mm) 2236.06
Lez / rz 139.09
Ley / ry 139.09
Actual Slenderness Ratio 139.09
Allowable Slenderness Ratio 400.00
Status SAFE

Check Against Axial Tension For Truss Member

Actual Tensile Stress ft (MPa)


=Fx / Anet 1.69

Print Time/Date: 07/12/2018 20:09 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 384 of 617
Job No Sheet No Rev
BN/SS/-01 385
Part
Software licensed to BN
Job Title Design of Overhead Gantry Hoarding Truss - 30m Span Ref

By Biswajit Date06-Dec-18 Chd Biswajit


Client Suntony Signage File Final Gantry Truss-30m Date/Time
Span.std 07-Dec-2018 20:06

Allowable Tensile Stress ft_allowable (MPa)


=0.60fy 144.00
Interaction ratio
=ft / ft_allowable 0.01
Status SAFE

Print Time/Date: 07/12/2018 20:09 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 385 of 617
Job No Sheet No Rev
BN/SS/-01 386
Part
Software licensed to BN
Job Title Design of Overhead Gantry Hoarding Truss - 30m Span Ref

By Biswajit Date06-Dec-18 Chd Biswajit


Client Suntony Signage File Final Gantry Truss-30m Date/Time
Span.std 07-Dec-2018 20:06

Design Of Member No. 184 As Per IS:800

Input Parameters

Member Section PIP483L

2
Cross Sectional Area Ax (mm ) 414.00
rz (mm) 16.08
ry (mm) 16.08
Unsupported Length - Major Axis For Slenderness Check Lz (mm) 2236.06
Unsupported Length - Minor Axis For Slenderness Check Ly (mm) 2236.06
Yield Stress fy (MPa) 240.00
Allowable Ratio For Interaction Check 1.00

Design Forces

Axial Load Fx (N ) 829.74


Critical Loadcase No. 3

Details Of Calculation

Slenderness Checking

Lez (mm) 2236.06


Ley (mm) 2236.06
Lez / rz 139.09
Ley / ry 139.09
Actual Slenderness Ratio 139.09
Allowable Slenderness Ratio 180.00
Status SAFE

Check Against Axial Compression For Truss Member

Actual Compressive Stress fc (MPa)


=Fx / Ax 2.00

Calculation Of Allowable Compressive Stress :

Print Time/Date: 07/12/2018 20:09 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 386 of 617
Job No Sheet No Rev
BN/SS/-01 387
Part
Software licensed to BN
Job Title Design of Overhead Gantry Hoarding Truss - 30m Span Ref

By Biswajit Date06-Dec-18 Chd Biswajit


Client Suntony Signage File Final Gantry Truss-30m Date/Time
Span.std 07-Dec-2018 20:06

E (MPa) 200000.00
L/r 139.09
fcc (MPa)
2 2
=π E / λ 102.03
Allowable Compressive Stress fc_allowable (MPa)
1.4 1.4
=0.6fccfy / [(fcc) + (fy) ] 50.70
Interaction ratio
=fc / fc_allowable 0.04
Status SAFE

Print Time/Date: 07/12/2018 20:09 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 387 of 617
Job No Sheet No Rev
BN/SS/-01 388
Part
Software licensed to BN
Job Title Design of Overhead Gantry Hoarding Truss - 30m Span Ref

By Biswajit Date06-Dec-18 Chd Biswajit


Client Suntony Signage File Final Gantry Truss-30m Date/Time
Span.std 07-Dec-2018 20:06

Design Of Member No. 185 As Per IS:800

Input Parameters

Member Section PIP483L

2
Cross Sectional Area Ax (mm ) 414.00
Net section factor 1.00
2
Net Effective Sectional Area Anet (mm ) 414.00
rz (mm) 16.08
ry (mm) 16.08
Unsupported Length - Major Axis For Slenderness Check Lz (mm) 2236.06
Unsupported Length - Minor Axis For Slenderness Check Ly (mm) 2236.06
Yield Stress fy (MPa) 240.00
Allowable Ratio For Interaction Check 1.00

Design Forces

Axial Load Fx (N ) -270.87


Critical Loadcase No. 3

Details Of Calculation

Slenderness Checking

Lez (mm) 2236.06


Ley (mm) 2236.06
Lez / rz 139.09
Ley / ry 139.09
Actual Slenderness Ratio 139.09
Allowable Slenderness Ratio 400.00
Status SAFE

Check Against Axial Tension For Truss Member

Actual Tensile Stress ft (MPa)


=Fx / Anet 0.65

Print Time/Date: 07/12/2018 20:09 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 388 of 617
Job No Sheet No Rev
BN/SS/-01 389
Part
Software licensed to BN
Job Title Design of Overhead Gantry Hoarding Truss - 30m Span Ref

By Biswajit Date06-Dec-18 Chd Biswajit


Client Suntony Signage File Final Gantry Truss-30m Date/Time
Span.std 07-Dec-2018 20:06

Allowable Tensile Stress ft_allowable (MPa)


=0.60fy 144.00
Interaction ratio
=ft / ft_allowable 0.00
Status SAFE

Print Time/Date: 07/12/2018 20:09 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 389 of 617
Job No Sheet No Rev
BN/SS/-01 390
Part
Software licensed to BN
Job Title Design of Overhead Gantry Hoarding Truss - 30m Span Ref

By Biswajit Date06-Dec-18 Chd Biswajit


Client Suntony Signage File Final Gantry Truss-30m Date/Time
Span.std 07-Dec-2018 20:06

Design Of Member No. 186 As Per IS:800

Input Parameters

Member Section PIP483L

2
Cross Sectional Area Ax (mm ) 414.00
rz (mm) 16.08
ry (mm) 16.08
Unsupported Length - Major Axis For Slenderness Check Lz (mm) 2236.06
Unsupported Length - Minor Axis For Slenderness Check Ly (mm) 2236.06
Yield Stress fy (MPa) 240.00
Allowable Ratio For Interaction Check 1.00

Design Forces

Axial Load Fx (N ) 883.25


Critical Loadcase No. 3

Details Of Calculation

Slenderness Checking

Lez (mm) 2236.06


Ley (mm) 2236.06
Lez / rz 139.09
Ley / ry 139.09
Actual Slenderness Ratio 139.09
Allowable Slenderness Ratio 180.00
Status SAFE

Check Against Axial Compression For Truss Member

Actual Compressive Stress fc (MPa)


=Fx / Ax 2.13

Calculation Of Allowable Compressive Stress :

Print Time/Date: 07/12/2018 20:09 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 390 of 617
Job No Sheet No Rev
BN/SS/-01 391
Part
Software licensed to BN
Job Title Design of Overhead Gantry Hoarding Truss - 30m Span Ref

By Biswajit Date06-Dec-18 Chd Biswajit


Client Suntony Signage File Final Gantry Truss-30m Date/Time
Span.std 07-Dec-2018 20:06

E (MPa) 200000.00
L/r 139.09
fcc (MPa)
2 2
=π E / λ 102.03
Allowable Compressive Stress fc_allowable (MPa)
1.4 1.4
=0.6fccfy / [(fcc) + (fy) ] 50.70
Interaction ratio
=fc / fc_allowable 0.04
Status SAFE

Print Time/Date: 07/12/2018 20:09 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 391 of 617
Job No Sheet No Rev
BN/SS/-01 392
Part
Software licensed to BN
Job Title Design of Overhead Gantry Hoarding Truss - 30m Span Ref

By Biswajit Date06-Dec-18 Chd Biswajit


Client Suntony Signage File Final Gantry Truss-30m Date/Time
Span.std 07-Dec-2018 20:06

Design Of Member No. 187 As Per IS:800

Input Parameters

Member Section PIP483L

2
Cross Sectional Area Ax (mm ) 414.00
rz (mm) 16.08
ry (mm) 16.08
Unsupported Length - Major Axis For Slenderness Check Lz (mm) 2236.06
Unsupported Length - Minor Axis For Slenderness Check Ly (mm) 2236.06
Yield Stress fy (MPa) 240.00
Allowable Ratio For Interaction Check 1.00

Design Forces

Axial Load Fx (N ) 667.53


Critical Loadcase No. 3

Details Of Calculation

Slenderness Checking

Lez (mm) 2236.06


Ley (mm) 2236.06
Lez / rz 139.09
Ley / ry 139.09
Actual Slenderness Ratio 139.09
Allowable Slenderness Ratio 180.00
Status SAFE

Check Against Axial Compression For Truss Member

Actual Compressive Stress fc (MPa)


=Fx / Ax 1.61

Calculation Of Allowable Compressive Stress :

Print Time/Date: 07/12/2018 20:09 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 392 of 617
Job No Sheet No Rev
BN/SS/-01 393
Part
Software licensed to BN
Job Title Design of Overhead Gantry Hoarding Truss - 30m Span Ref

By Biswajit Date06-Dec-18 Chd Biswajit


Client Suntony Signage File Final Gantry Truss-30m Date/Time
Span.std 07-Dec-2018 20:06

E (MPa) 200000.00
L/r 139.09
fcc (MPa)
2 2
=π E / λ 102.03
Allowable Compressive Stress fc_allowable (MPa)
1.4 1.4
=0.6fccfy / [(fcc) + (fy) ] 50.70
Interaction ratio
=fc / fc_allowable 0.03
Status SAFE

Print Time/Date: 07/12/2018 20:09 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 393 of 617
Job No Sheet No Rev
BN/SS/-01 394
Part
Software licensed to BN
Job Title Design of Overhead Gantry Hoarding Truss - 30m Span Ref

By Biswajit Date06-Dec-18 Chd Biswajit


Client Suntony Signage File Final Gantry Truss-30m Date/Time
Span.std 07-Dec-2018 20:06

Design Of Member No. 188 As Per IS:800

Input Parameters

Member Section PIP483L

2
Cross Sectional Area Ax (mm ) 414.00
rz (mm) 16.08
ry (mm) 16.08
Unsupported Length - Major Axis For Slenderness Check Lz (mm) 2236.06
Unsupported Length - Minor Axis For Slenderness Check Ly (mm) 2236.06
Yield Stress fy (MPa) 240.00
Allowable Ratio For Interaction Check 1.00

Design Forces

Axial Load Fx (N ) 703.09


Critical Loadcase No. 3

Details Of Calculation

Slenderness Checking

Lez (mm) 2236.06


Ley (mm) 2236.06
Lez / rz 139.09
Ley / ry 139.09
Actual Slenderness Ratio 139.09
Allowable Slenderness Ratio 180.00
Status SAFE

Check Against Axial Compression For Truss Member

Actual Compressive Stress fc (MPa)


=Fx / Ax 1.70

Calculation Of Allowable Compressive Stress :

Print Time/Date: 07/12/2018 20:09 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 394 of 617
Job No Sheet No Rev
BN/SS/-01 395
Part
Software licensed to BN
Job Title Design of Overhead Gantry Hoarding Truss - 30m Span Ref

By Biswajit Date06-Dec-18 Chd Biswajit


Client Suntony Signage File Final Gantry Truss-30m Date/Time
Span.std 07-Dec-2018 20:06

E (MPa) 200000.00
L/r 139.09
fcc (MPa)
2 2
=π E / λ 102.03
Allowable Compressive Stress fc_allowable (MPa)
1.4 1.4
=0.6fccfy / [(fcc) + (fy) ] 50.70
Interaction ratio
=fc / fc_allowable 0.03
Status SAFE

Print Time/Date: 07/12/2018 20:09 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 395 of 617
Job No Sheet No Rev
BN/SS/-01 396
Part
Software licensed to BN
Job Title Design of Overhead Gantry Hoarding Truss - 30m Span Ref

By Biswajit Date06-Dec-18 Chd Biswajit


Client Suntony Signage File Final Gantry Truss-30m Date/Time
Span.std 07-Dec-2018 20:06

Design Of Member No. 189 As Per IS:800

Input Parameters

Member Section PIP483L

2
Cross Sectional Area Ax (mm ) 414.00
rz (mm) 16.08
ry (mm) 16.08
Unsupported Length - Major Axis For Slenderness Check Lz (mm) 2236.06
Unsupported Length - Minor Axis For Slenderness Check Ly (mm) 2236.06
Yield Stress fy (MPa) 240.00
Allowable Ratio For Interaction Check 1.00

Design Forces

Axial Load Fx (N ) 12291.98


Critical Loadcase No. 3

Details Of Calculation

Slenderness Checking

Lez (mm) 2236.06


Ley (mm) 2236.06
Lez / rz 139.09
Ley / ry 139.09
Actual Slenderness Ratio 139.09
Allowable Slenderness Ratio 180.00
Status SAFE

Check Against Axial Compression For Truss Member

Actual Compressive Stress fc (MPa)


=Fx / Ax 29.69

Calculation Of Allowable Compressive Stress :

Print Time/Date: 07/12/2018 20:09 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 396 of 617
Job No Sheet No Rev
BN/SS/-01 397
Part
Software licensed to BN
Job Title Design of Overhead Gantry Hoarding Truss - 30m Span Ref

By Biswajit Date06-Dec-18 Chd Biswajit


Client Suntony Signage File Final Gantry Truss-30m Date/Time
Span.std 07-Dec-2018 20:06

E (MPa) 200000.00
L/r 139.09
fcc (MPa)
2 2
=π E / λ 102.03
Allowable Compressive Stress fc_allowable (MPa)
1.4 1.4
=0.6fccfy / [(fcc) + (fy) ] 50.70
Interaction ratio
=fc / fc_allowable 0.59
Status SAFE

Print Time/Date: 07/12/2018 20:09 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 397 of 617
Job No Sheet No Rev
BN/SS/-01 398
Part
Software licensed to BN
Job Title Design of Overhead Gantry Hoarding Truss - 30m Span Ref

By Biswajit Date06-Dec-18 Chd Biswajit


Client Suntony Signage File Final Gantry Truss-30m Date/Time
Span.std 07-Dec-2018 20:06

Design Of Member No. 190 As Per IS:800

Input Parameters

Member Section PIP603L

2
Cross Sectional Area Ax (mm ) 523.00
rz (mm) 20.32
ry (mm) 20.32
Unsupported Length - Major Axis For Slenderness Check Lz (mm) 1802.77
Unsupported Length - Minor Axis For Slenderness Check Ly (mm) 1802.77
Yield Stress fy (MPa) 240.00
Allowable Ratio For Interaction Check 1.00

Design Forces

Axial Load Fx (N ) 16167.31


Critical Loadcase No. 3

Details Of Calculation

Slenderness Checking

Lez (mm) 1802.77


Ley (mm) 1802.77
Lez / rz 88.71
Ley / ry 88.71
Actual Slenderness Ratio 88.71
Allowable Slenderness Ratio 180.00
Status SAFE

Check Against Axial Compression For Truss Member

Actual Compressive Stress fc (MPa)


=Fx / Ax 30.91

Calculation Of Allowable Compressive Stress :

Print Time/Date: 07/12/2018 20:09 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 398 of 617
Job No Sheet No Rev
BN/SS/-01 399
Part
Software licensed to BN
Job Title Design of Overhead Gantry Hoarding Truss - 30m Span Ref

By Biswajit Date06-Dec-18 Chd Biswajit


Client Suntony Signage File Final Gantry Truss-30m Date/Time
Span.std 07-Dec-2018 20:06

E (MPa) 200000.00
L/r 88.71
fcc (MPa)
2 2
=π E / λ 250.84
Allowable Compressive Stress fc_allowable (MPa)
1.4 1.4
=0.6fccfy / [(fcc) + (fy) ] 89.69
Interaction ratio
=fc / fc_allowable 0.34
Status SAFE

Print Time/Date: 07/12/2018 20:09 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 399 of 617
Job No Sheet No Rev
BN/SS/-01 400
Part
Software licensed to BN
Job Title Design of Overhead Gantry Hoarding Truss - 30m Span Ref

By Biswajit Date06-Dec-18 Chd Biswajit


Client Suntony Signage File Final Gantry Truss-30m Date/Time
Span.std 07-Dec-2018 20:06

Design Of Member No. 191 As Per IS:800

Input Parameters

Member Section PIP603L

2
Cross Sectional Area Ax (mm ) 523.00
rz (mm) 20.32
ry (mm) 20.32
Unsupported Length - Major Axis For Slenderness Check Lz (mm) 1802.77
Unsupported Length - Minor Axis For Slenderness Check Ly (mm) 1802.77
Yield Stress fy (MPa) 240.00
Allowable Ratio For Interaction Check 1.00

Design Forces

Axial Load Fx (N ) 13031.30


Critical Loadcase No. 3

Details Of Calculation

Slenderness Checking

Lez (mm) 1802.77


Ley (mm) 1802.77
Lez / rz 88.71
Ley / ry 88.71
Actual Slenderness Ratio 88.71
Allowable Slenderness Ratio 180.00
Status SAFE

Check Against Axial Compression For Truss Member

Actual Compressive Stress fc (MPa)


=Fx / Ax 24.92

Calculation Of Allowable Compressive Stress :

Print Time/Date: 07/12/2018 20:09 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 400 of 617
Job No Sheet No Rev
BN/SS/-01 401
Part
Software licensed to BN
Job Title Design of Overhead Gantry Hoarding Truss - 30m Span Ref

By Biswajit Date06-Dec-18 Chd Biswajit


Client Suntony Signage File Final Gantry Truss-30m Date/Time
Span.std 07-Dec-2018 20:06

E (MPa) 200000.00
L/r 88.71
fcc (MPa)
2 2
=π E / λ 250.84
Allowable Compressive Stress fc_allowable (MPa)
1.4 1.4
=0.6fccfy / [(fcc) + (fy) ] 89.69
Interaction ratio
=fc / fc_allowable 0.28
Status SAFE

Print Time/Date: 07/12/2018 20:09 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 401 of 617
Job No Sheet No Rev
BN/SS/-01 402
Part
Software licensed to BN
Job Title Design of Overhead Gantry Hoarding Truss - 30m Span Ref

By Biswajit Date06-Dec-18 Chd Biswajit


Client Suntony Signage File Final Gantry Truss-30m Date/Time
Span.std 07-Dec-2018 20:06

Design Of Member No. 192 As Per IS:800

Input Parameters

Member Section PIP2191H

2
Cross Sectional Area Ax (mm ) 3950.00
rz (mm) 75.42
ry (mm) 75.42
Unsupported Length - Major Axis For Slenderness Check Lz (mm) 1083.34
Unsupported Length - Minor Axis For Slenderness Check Ly (mm) 1083.34
Yield Stress fy (MPa) 240.00
Allowable Ratio For Interaction Check 1.00

Design Forces

Axial Load Fx (N ) 104069.47


Critical Loadcase No. 3

Details Of Calculation

Slenderness Checking

Lez (mm) 1083.34


Ley (mm) 1083.34
Lez / rz 14.36
Ley / ry 14.36
Actual Slenderness Ratio 14.36
Allowable Slenderness Ratio 180.00
Status SAFE

Check Against Axial Compression For Truss Member

Actual Compressive Stress fc (MPa)


=Fx / Ax 26.35

Calculation Of Allowable Compressive Stress :

Print Time/Date: 07/12/2018 20:09 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 402 of 617
Job No Sheet No Rev
BN/SS/-01 403
Part
Software licensed to BN
Job Title Design of Overhead Gantry Hoarding Truss - 30m Span Ref

By Biswajit Date06-Dec-18 Chd Biswajit


Client Suntony Signage File Final Gantry Truss-30m Date/Time
Span.std 07-Dec-2018 20:06

E (MPa) 200000.00
L/r 14.36
fcc (MPa)
2 2
=π E / λ 9567.70
Allowable Compressive Stress fc_allowable (MPa)
1.4 1.4
=0.6fccfy / [(fcc) + (fy) ] 143.40
Interaction ratio
=fc / fc_allowable 0.18
Status SAFE

Print Time/Date: 07/12/2018 20:09 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 403 of 617
Job No Sheet No Rev
BN/SS/-01 404
Part
Software licensed to BN
Job Title Design of Overhead Gantry Hoarding Truss - 30m Span Ref

By Biswajit Date06-Dec-18 Chd Biswajit


Client Suntony Signage File Final Gantry Truss-30m Date/Time
Span.std 07-Dec-2018 20:06

Design Of Member No. 193 As Per IS:800

Input Parameters

Member Section PIP2191H

2
Cross Sectional Area Ax (mm ) 3950.00
Net section factor 1.00
2
Net Effective Sectional Area Anet (mm ) 3950.00
rz (mm) 75.42
ry (mm) 75.42
Unsupported Length - Major Axis For Slenderness Check Lz (mm) 1083.34
Unsupported Length - Minor Axis For Slenderness Check Ly (mm) 1083.34
Yield Stress fy (MPa) 240.00
Allowable Ratio For Interaction Check 1.00

Design Forces

Axial Load Fx (N ) -105914.82


Critical Loadcase No. 3

Details Of Calculation

Slenderness Checking

Lez (mm) 1083.34


Ley (mm) 1083.34
Lez / rz 14.36
Ley / ry 14.36
Actual Slenderness Ratio 14.36
Allowable Slenderness Ratio 400.00
Status SAFE

Check Against Axial Tension For Truss Member

Actual Tensile Stress ft (MPa)


=Fx / Anet 26.81

Print Time/Date: 07/12/2018 20:09 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 404 of 617
Job No Sheet No Rev
BN/SS/-01 405
Part
Software licensed to BN
Job Title Design of Overhead Gantry Hoarding Truss - 30m Span Ref

By Biswajit Date06-Dec-18 Chd Biswajit


Client Suntony Signage File Final Gantry Truss-30m Date/Time
Span.std 07-Dec-2018 20:06

Allowable Tensile Stress ft_allowable (MPa)


=0.60fy 144.00
Interaction ratio
=ft / ft_allowable 0.19
Status SAFE

Print Time/Date: 07/12/2018 20:09 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 405 of 617
Job No Sheet No Rev
BN/SS/-01 406
Part
Software licensed to BN
Job Title Design of Overhead Gantry Hoarding Truss - 30m Span Ref

By Biswajit Date06-Dec-18 Chd Biswajit


Client Suntony Signage File Final Gantry Truss-30m Date/Time
Span.std 07-Dec-2018 20:06

Design Of Member No. 194 As Per IS:800

Input Parameters

Member Section PIP2191H

2
Cross Sectional Area Ax (mm ) 3950.00
rz (mm) 75.42
ry (mm) 75.42
Unsupported Length - Major Axis For Slenderness Check Lz (mm) 1083.34
Unsupported Length - Minor Axis For Slenderness Check Ly (mm) 1083.34
Yield Stress fy (MPa) 240.00
Allowable Ratio For Interaction Check 1.00

Design Forces

Axial Load Fx (N ) 168177.95


Critical Loadcase No. 3

Details Of Calculation

Slenderness Checking

Lez (mm) 1083.34


Ley (mm) 1083.34
Lez / rz 14.36
Ley / ry 14.36
Actual Slenderness Ratio 14.36
Allowable Slenderness Ratio 180.00
Status SAFE

Check Against Axial Compression For Truss Member

Actual Compressive Stress fc (MPa)


=Fx / Ax 42.58

Calculation Of Allowable Compressive Stress :

Print Time/Date: 07/12/2018 20:09 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 406 of 617
Job No Sheet No Rev
BN/SS/-01 407
Part
Software licensed to BN
Job Title Design of Overhead Gantry Hoarding Truss - 30m Span Ref

By Biswajit Date06-Dec-18 Chd Biswajit


Client Suntony Signage File Final Gantry Truss-30m Date/Time
Span.std 07-Dec-2018 20:06

E (MPa) 200000.00
L/r 14.36
fcc (MPa)
2 2
=π E / λ 9567.70
Allowable Compressive Stress fc_allowable (MPa)
1.4 1.4
=0.6fccfy / [(fcc) + (fy) ] 143.40
Interaction ratio
=fc / fc_allowable 0.30
Status SAFE

Print Time/Date: 07/12/2018 20:09 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 407 of 617
Job No Sheet No Rev
BN/SS/-01 408
Part
Software licensed to BN
Job Title Design of Overhead Gantry Hoarding Truss - 30m Span Ref

By Biswajit Date06-Dec-18 Chd Biswajit


Client Suntony Signage File Final Gantry Truss-30m Date/Time
Span.std 07-Dec-2018 20:06

Design Of Member No. 195 As Per IS:800

Input Parameters

Member Section PIP2191H

2
Cross Sectional Area Ax (mm ) 3950.00
Net section factor 1.00
2
Net Effective Sectional Area Anet (mm ) 3950.00
rz (mm) 75.42
ry (mm) 75.42
Unsupported Length - Major Axis For Slenderness Check Lz (mm) 1083.34
Unsupported Length - Minor Axis For Slenderness Check Ly (mm) 1083.34
Yield Stress fy (MPa) 240.00
Allowable Ratio For Interaction Check 1.00

Design Forces

Axial Load Fx (N ) -124112.35


Critical Loadcase No. 3

Details Of Calculation

Slenderness Checking

Lez (mm) 1083.34


Ley (mm) 1083.34
Lez / rz 14.36
Ley / ry 14.36
Actual Slenderness Ratio 14.36
Allowable Slenderness Ratio 400.00
Status SAFE

Check Against Axial Tension For Truss Member

Actual Tensile Stress ft (MPa)


=Fx / Anet 31.42

Print Time/Date: 07/12/2018 20:09 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 408 of 617
Job No Sheet No Rev
BN/SS/-01 409
Part
Software licensed to BN
Job Title Design of Overhead Gantry Hoarding Truss - 30m Span Ref

By Biswajit Date06-Dec-18 Chd Biswajit


Client Suntony Signage File Final Gantry Truss-30m Date/Time
Span.std 07-Dec-2018 20:06

Allowable Tensile Stress ft_allowable (MPa)


=0.60fy 144.00
Interaction ratio
=ft / ft_allowable 0.22
Status SAFE

Print Time/Date: 07/12/2018 20:09 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 409 of 617
Job No Sheet No Rev
BN/SS/-01 410
Part
Software licensed to BN
Job Title Design of Overhead Gantry Hoarding Truss - 30m Span Ref

By Biswajit Date06-Dec-18 Chd Biswajit


Client Suntony Signage File Final Gantry Truss-30m Date/Time
Span.std 07-Dec-2018 20:06

Design Of Member No. 196 As Per IS:800

Input Parameters

Member Section PIP2191H

2
Cross Sectional Area Ax (mm ) 3950.00
rz (mm) 75.42
ry (mm) 75.42
Unsupported Length - Major Axis For Slenderness Check Lz (mm) 1083.34
Unsupported Length - Minor Axis For Slenderness Check Ly (mm) 1083.34
Yield Stress fy (MPa) 240.00
Allowable Ratio For Interaction Check 1.00

Design Forces

Axial Load Fx (N ) 203424.59


Critical Loadcase No. 3

Details Of Calculation

Slenderness Checking

Lez (mm) 1083.34


Ley (mm) 1083.34
Lez / rz 14.36
Ley / ry 14.36
Actual Slenderness Ratio 14.36
Allowable Slenderness Ratio 180.00
Status SAFE

Check Against Axial Compression For Truss Member

Actual Compressive Stress fc (MPa)


=Fx / Ax 51.50

Calculation Of Allowable Compressive Stress :

Print Time/Date: 07/12/2018 20:09 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 410 of 617
Job No Sheet No Rev
BN/SS/-01 411
Part
Software licensed to BN
Job Title Design of Overhead Gantry Hoarding Truss - 30m Span Ref

By Biswajit Date06-Dec-18 Chd Biswajit


Client Suntony Signage File Final Gantry Truss-30m Date/Time
Span.std 07-Dec-2018 20:06

E (MPa) 200000.00
L/r 14.36
fcc (MPa)
2 2
=π E / λ 9567.70
Allowable Compressive Stress fc_allowable (MPa)
1.4 1.4
=0.6fccfy / [(fcc) + (fy) ] 143.40
Interaction ratio
=fc / fc_allowable 0.36
Status SAFE

Print Time/Date: 07/12/2018 20:09 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 411 of 617
Job No Sheet No Rev
BN/SS/-01 412
Part
Software licensed to BN
Job Title Design of Overhead Gantry Hoarding Truss - 30m Span Ref

By Biswajit Date06-Dec-18 Chd Biswajit


Client Suntony Signage File Final Gantry Truss-30m Date/Time
Span.std 07-Dec-2018 20:06

Design Of Member No. 197 As Per IS:800

Input Parameters

Member Section PIP2191H

2
Cross Sectional Area Ax (mm ) 3950.00
Net section factor 1.00
2
Net Effective Sectional Area Anet (mm ) 3950.00
rz (mm) 75.42
ry (mm) 75.42
Unsupported Length - Major Axis For Slenderness Check Lz (mm) 1083.34
Unsupported Length - Minor Axis For Slenderness Check Ly (mm) 1083.34
Yield Stress fy (MPa) 240.00
Allowable Ratio For Interaction Check 1.00

Design Forces

Axial Load Fx (N ) -175861.94


Critical Loadcase No. 3

Details Of Calculation

Slenderness Checking

Lez (mm) 1083.34


Ley (mm) 1083.34
Lez / rz 14.36
Ley / ry 14.36
Actual Slenderness Ratio 14.36
Allowable Slenderness Ratio 400.00
Status SAFE

Check Against Axial Tension For Truss Member

Actual Tensile Stress ft (MPa)


=Fx / Anet 44.52

Print Time/Date: 07/12/2018 20:09 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 412 of 617
Job No Sheet No Rev
BN/SS/-01 413
Part
Software licensed to BN
Job Title Design of Overhead Gantry Hoarding Truss - 30m Span Ref

By Biswajit Date06-Dec-18 Chd Biswajit


Client Suntony Signage File Final Gantry Truss-30m Date/Time
Span.std 07-Dec-2018 20:06

Allowable Tensile Stress ft_allowable (MPa)


=0.60fy 144.00
Interaction ratio
=ft / ft_allowable 0.31
Status SAFE

Print Time/Date: 07/12/2018 20:09 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 413 of 617
Job No Sheet No Rev
BN/SS/-01 414
Part
Software licensed to BN
Job Title Design of Overhead Gantry Hoarding Truss - 30m Span Ref

By Biswajit Date06-Dec-18 Chd Biswajit


Client Suntony Signage File Final Gantry Truss-30m Date/Time
Span.std 07-Dec-2018 20:06

Design Of Member No. 198 As Per IS:800

Input Parameters

Member Section PIP2191H

2
Cross Sectional Area Ax (mm ) 3950.00
rz (mm) 75.42
ry (mm) 75.42
Unsupported Length - Major Axis For Slenderness Check Lz (mm) 1083.34
Unsupported Length - Minor Axis For Slenderness Check Ly (mm) 1083.34
Yield Stress fy (MPa) 240.00
Allowable Ratio For Interaction Check 1.00

Design Forces

Axial Load Fx (N ) 24745.43


Critical Loadcase No. 3

Details Of Calculation

Slenderness Checking

Lez (mm) 1083.34


Ley (mm) 1083.34
Lez / rz 14.36
Ley / ry 14.36
Actual Slenderness Ratio 14.36
Allowable Slenderness Ratio 180.00
Status SAFE

Check Against Axial Compression For Truss Member

Actual Compressive Stress fc (MPa)


=Fx / Ax 6.26

Calculation Of Allowable Compressive Stress :

Print Time/Date: 07/12/2018 20:09 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 414 of 617
Job No Sheet No Rev
BN/SS/-01 415
Part
Software licensed to BN
Job Title Design of Overhead Gantry Hoarding Truss - 30m Span Ref

By Biswajit Date06-Dec-18 Chd Biswajit


Client Suntony Signage File Final Gantry Truss-30m Date/Time
Span.std 07-Dec-2018 20:06

E (MPa) 200000.00
L/r 14.36
fcc (MPa)
2 2
=π E / λ 9567.70
Allowable Compressive Stress fc_allowable (MPa)
1.4 1.4
=0.6fccfy / [(fcc) + (fy) ] 143.40
Interaction ratio
=fc / fc_allowable 0.04
Status SAFE

Print Time/Date: 07/12/2018 20:09 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 415 of 617
Job No Sheet No Rev
BN/SS/-01 416
Part
Software licensed to BN
Job Title Design of Overhead Gantry Hoarding Truss - 30m Span Ref

By Biswajit Date06-Dec-18 Chd Biswajit


Client Suntony Signage File Final Gantry Truss-30m Date/Time
Span.std 07-Dec-2018 20:06

Design Of Member No. 199 As Per IS:800

Input Parameters

Member Section PIP2191H

2
Cross Sectional Area Ax (mm ) 3950.00
Net section factor 1.00
2
Net Effective Sectional Area Anet (mm ) 3950.00
rz (mm) 75.42
ry (mm) 75.42
Unsupported Length - Major Axis For Slenderness Check Lz (mm) 1083.34
Unsupported Length - Minor Axis For Slenderness Check Ly (mm) 1083.34
Yield Stress fy (MPa) 240.00
Allowable Ratio For Interaction Check 1.00

Design Forces

Axial Load Fx (N ) -34496.73


Critical Loadcase No. 3

Details Of Calculation

Slenderness Checking

Lez (mm) 1083.34


Ley (mm) 1083.34
Lez / rz 14.36
Ley / ry 14.36
Actual Slenderness Ratio 14.36
Allowable Slenderness Ratio 400.00
Status SAFE

Check Against Axial Tension For Truss Member

Actual Tensile Stress ft (MPa)


=Fx / Anet 8.73

Print Time/Date: 07/12/2018 20:09 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 416 of 617
Job No Sheet No Rev
BN/SS/-01 417
Part
Software licensed to BN
Job Title Design of Overhead Gantry Hoarding Truss - 30m Span Ref

By Biswajit Date06-Dec-18 Chd Biswajit


Client Suntony Signage File Final Gantry Truss-30m Date/Time
Span.std 07-Dec-2018 20:06

Allowable Tensile Stress ft_allowable (MPa)


=0.60fy 144.00
Interaction ratio
=ft / ft_allowable 0.06
Status SAFE

Print Time/Date: 07/12/2018 20:09 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 417 of 617
Job No Sheet No Rev
BN/SS/-01 418
Part
Software licensed to BN
Job Title Design of Overhead Gantry Hoarding Truss - 30m Span Ref

By Biswajit Date06-Dec-18 Chd Biswajit


Client Suntony Signage File Final Gantry Truss-30m Date/Time
Span.std 07-Dec-2018 20:06

Design Of Member No. 200 As Per IS:800

Input Parameters

Member Section PIP1524L

2
Cross Sectional Area Ax (mm ) 2090.00
Net section factor 1.00
2
Net Effective Sectional Area Anet (mm ) 2090.00
rz (mm) 52.31
ry (mm) 52.31
Unsupported Length - Major Axis For Slenderness Check Lz (mm) 1500.00
Unsupported Length - Minor Axis For Slenderness Check Ly (mm) 1500.00
Yield Stress fy (MPa) 240.00
Allowable Ratio For Interaction Check 1.00

Design Forces

Axial Load Fx (N ) -20814.25


Critical Loadcase No. 3

Details Of Calculation

Slenderness Checking

Lez (mm) 1500.00


Ley (mm) 1500.00
Lez / rz 28.67
Ley / ry 28.67
Actual Slenderness Ratio 28.67
Allowable Slenderness Ratio 400.00
Status SAFE

Check Against Axial Tension For Truss Member

Actual Tensile Stress ft (MPa)


=Fx / Anet 9.96

Print Time/Date: 07/12/2018 20:09 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 418 of 617
Job No Sheet No Rev
BN/SS/-01 419
Part
Software licensed to BN
Job Title Design of Overhead Gantry Hoarding Truss - 30m Span Ref

By Biswajit Date06-Dec-18 Chd Biswajit


Client Suntony Signage File Final Gantry Truss-30m Date/Time
Span.std 07-Dec-2018 20:06

Allowable Tensile Stress ft_allowable (MPa)


=0.60fy 144.00
Interaction ratio
=ft / ft_allowable 0.07
Status SAFE

Print Time/Date: 07/12/2018 20:09 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 419 of 617
Job No Sheet No Rev
BN/SS/-01 420
Part
Software licensed to BN
Job Title Design of Overhead Gantry Hoarding Truss - 30m Span Ref

By Biswajit Date06-Dec-18 Chd Biswajit


Client Suntony Signage File Final Gantry Truss-30m Date/Time
Span.std 07-Dec-2018 20:06

Design Of Member No. 201 As Per IS:800

Input Parameters

Member Section PIP1524L

2
Cross Sectional Area Ax (mm ) 0.00
rz (mm) 52.31
ry (mm) 52.31
Unsupported Length - Major Axis For Slenderness Check Lz (mm) 1000.00
Unsupported Length - Minor Axis For Slenderness Check Ly (mm) 1000.00
Yield Stress fy (MPa) 0.00
Allowable Ratio For Interaction Check 1.00

Design Forces

Axial Load Fx (N ) 0.00


Critical Loadcase No. 0

Details Of Calculation

Slenderness Checking

Lez (mm) 1000.00


Ley (mm) 1000.00
Lez / rz 19.11
Ley / ry 19.11
Actual Slenderness Ratio 19.11
Allowable Slenderness Ratio 400.00
Status SAFE

Check Against Axial Compression For Truss Member

Actual Compressive Stress fc (MPa)


=Fx / Ax 0.00

Calculation Of Allowable Compressive Stress :

Print Time/Date: 07/12/2018 20:09 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 420 of 617
Job No Sheet No Rev
BN/SS/-01 421
Part
Software licensed to BN
Job Title Design of Overhead Gantry Hoarding Truss - 30m Span Ref

By Biswajit Date06-Dec-18 Chd Biswajit


Client Suntony Signage File Final Gantry Truss-30m Date/Time
Span.std 07-Dec-2018 20:06

E (MPa) 200000.00
L/r 19.11
fcc (MPa)
2 2
=π E / λ 5402.33
Allowable Compressive Stress fc_allowable (MPa)
1.4 1.4
=0.6fccfy / [(fcc) + (fy) ] 0.00
Interaction ratio
=fc / fc_allowable 0.00
Status SAFE

Print Time/Date: 07/12/2018 20:09 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 421 of 617
Job No Sheet No Rev
BN/SS/-01 422
Part
Software licensed to BN
Job Title Design of Overhead Gantry Hoarding Truss - 30m Span Ref

By Biswajit Date06-Dec-18 Chd Biswajit


Client Suntony Signage File Final Gantry Truss-30m Date/Time
Span.std 07-Dec-2018 20:06

Design Of Member No. 202 As Per IS:800

Input Parameters

Member Section PIP1524L

2
Cross Sectional Area Ax (mm ) 2090.00
Net section factor 1.00
2
Net Effective Sectional Area Anet (mm ) 2090.00
rz (mm) 52.31
ry (mm) 52.31
Unsupported Length - Major Axis For Slenderness Check Lz (mm) 1500.00
Unsupported Length - Minor Axis For Slenderness Check Ly (mm) 1500.00
Yield Stress fy (MPa) 240.00
Allowable Ratio For Interaction Check 1.00

Design Forces

Axial Load Fx (N ) -10211.19


Critical Loadcase No. 3

Details Of Calculation

Slenderness Checking

Lez (mm) 1500.00


Ley (mm) 1500.00
Lez / rz 28.67
Ley / ry 28.67
Actual Slenderness Ratio 28.67
Allowable Slenderness Ratio 400.00
Status SAFE

Check Against Axial Tension For Truss Member

Actual Tensile Stress ft (MPa)


=Fx / Anet 4.89

Print Time/Date: 07/12/2018 20:09 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 422 of 617
Job No Sheet No Rev
BN/SS/-01 423
Part
Software licensed to BN
Job Title Design of Overhead Gantry Hoarding Truss - 30m Span Ref

By Biswajit Date06-Dec-18 Chd Biswajit


Client Suntony Signage File Final Gantry Truss-30m Date/Time
Span.std 07-Dec-2018 20:06

Allowable Tensile Stress ft_allowable (MPa)


=0.60fy 144.00
Interaction ratio
=ft / ft_allowable 0.03
Status SAFE

Print Time/Date: 07/12/2018 20:09 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 423 of 617
Job No Sheet No Rev
BN/SS/-01 424
Part
Software licensed to BN
Job Title Design of Overhead Gantry Hoarding Truss - 30m Span Ref

By Biswajit Date06-Dec-18 Chd Biswajit


Client Suntony Signage File Final Gantry Truss-30m Date/Time
Span.std 07-Dec-2018 20:06

Design Of Member No. 203 As Per IS:800

Input Parameters

Member Section PIP1524L

2
Cross Sectional Area Ax (mm ) 0.00
rz (mm) 52.31
ry (mm) 52.31
Unsupported Length - Major Axis For Slenderness Check Lz (mm) 1000.00
Unsupported Length - Minor Axis For Slenderness Check Ly (mm) 1000.00
Yield Stress fy (MPa) 0.00
Allowable Ratio For Interaction Check 1.00

Design Forces

Axial Load Fx (N ) 0.00


Critical Loadcase No. 0

Details Of Calculation

Slenderness Checking

Lez (mm) 1000.00


Ley (mm) 1000.00
Lez / rz 19.11
Ley / ry 19.11
Actual Slenderness Ratio 19.11
Allowable Slenderness Ratio 400.00
Status SAFE

Check Against Axial Compression For Truss Member

Actual Compressive Stress fc (MPa)


=Fx / Ax 0.00

Calculation Of Allowable Compressive Stress :

Print Time/Date: 07/12/2018 20:09 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 424 of 617
Job No Sheet No Rev
BN/SS/-01 425
Part
Software licensed to BN
Job Title Design of Overhead Gantry Hoarding Truss - 30m Span Ref

By Biswajit Date06-Dec-18 Chd Biswajit


Client Suntony Signage File Final Gantry Truss-30m Date/Time
Span.std 07-Dec-2018 20:06

E (MPa) 200000.00
L/r 19.11
fcc (MPa)
2 2
=π E / λ 5402.33
Allowable Compressive Stress fc_allowable (MPa)
1.4 1.4
=0.6fccfy / [(fcc) + (fy) ] 0.00
Interaction ratio
=fc / fc_allowable 0.00
Status SAFE

Print Time/Date: 07/12/2018 20:09 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 425 of 617
Job No Sheet No Rev
BN/SS/-01 426
Part
Software licensed to BN
Job Title Design of Overhead Gantry Hoarding Truss - 30m Span Ref

By Biswajit Date06-Dec-18 Chd Biswajit


Client Suntony Signage File Final Gantry Truss-30m Date/Time
Span.std 07-Dec-2018 20:06

Design Of Member No. 204 As Per IS:800

Input Parameters

Member Section PIP1524L

2
Cross Sectional Area Ax (mm ) 0.00
rz (mm) 52.31
ry (mm) 52.31
Unsupported Length - Major Axis For Slenderness Check Lz (mm) 1500.00
Unsupported Length - Minor Axis For Slenderness Check Ly (mm) 1500.00
Yield Stress fy (MPa) 0.00
Allowable Ratio For Interaction Check 1.00

Design Forces

Axial Load Fx (N ) 0.00


Critical Loadcase No. 0

Details Of Calculation

Slenderness Checking

Lez (mm) 1500.00


Ley (mm) 1500.00
Lez / rz 28.67
Ley / ry 28.67
Actual Slenderness Ratio 28.67
Allowable Slenderness Ratio 400.00
Status SAFE

Check Against Axial Compression For Truss Member

Actual Compressive Stress fc (MPa)


=Fx / Ax 0.00

Calculation Of Allowable Compressive Stress :

Print Time/Date: 07/12/2018 20:09 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 426 of 617
Job No Sheet No Rev
BN/SS/-01 427
Part
Software licensed to BN
Job Title Design of Overhead Gantry Hoarding Truss - 30m Span Ref

By Biswajit Date06-Dec-18 Chd Biswajit


Client Suntony Signage File Final Gantry Truss-30m Date/Time
Span.std 07-Dec-2018 20:06

E (MPa) 200000.00
L/r 28.67
fcc (MPa)
2 2
=π E / λ 2401.04
Allowable Compressive Stress fc_allowable (MPa)
1.4 1.4
=0.6fccfy / [(fcc) + (fy) ] 0.00
Interaction ratio
=fc / fc_allowable 0.00
Status SAFE

Print Time/Date: 07/12/2018 20:09 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 427 of 617
Job No Sheet No Rev
BN/SS/-01 428
Part
Software licensed to BN
Job Title Design of Overhead Gantry Hoarding Truss - 30m Span Ref

By Biswajit Date06-Dec-18 Chd Biswajit


Client Suntony Signage File Final Gantry Truss-30m Date/Time
Span.std 07-Dec-2018 20:06

Design Of Member No. 205 As Per IS:800

Input Parameters

Member Section PIP1524L

2
Cross Sectional Area Ax (mm ) 0.00
rz (mm) 52.31
ry (mm) 52.31
Unsupported Length - Major Axis For Slenderness Check Lz (mm) 1000.00
Unsupported Length - Minor Axis For Slenderness Check Ly (mm) 1000.00
Yield Stress fy (MPa) 0.00
Allowable Ratio For Interaction Check 1.00

Design Forces

Axial Load Fx (N ) 0.00


Critical Loadcase No. 0

Details Of Calculation

Slenderness Checking

Lez (mm) 1000.00


Ley (mm) 1000.00
Lez / rz 19.11
Ley / ry 19.11
Actual Slenderness Ratio 19.11
Allowable Slenderness Ratio 400.00
Status SAFE

Check Against Axial Compression For Truss Member

Actual Compressive Stress fc (MPa)


=Fx / Ax 0.00

Calculation Of Allowable Compressive Stress :

Print Time/Date: 07/12/2018 20:09 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 428 of 617
Job No Sheet No Rev
BN/SS/-01 429
Part
Software licensed to BN
Job Title Design of Overhead Gantry Hoarding Truss - 30m Span Ref

By Biswajit Date06-Dec-18 Chd Biswajit


Client Suntony Signage File Final Gantry Truss-30m Date/Time
Span.std 07-Dec-2018 20:06

E (MPa) 200000.00
L/r 19.11
fcc (MPa)
2 2
=π E / λ 5402.33
Allowable Compressive Stress fc_allowable (MPa)
1.4 1.4
=0.6fccfy / [(fcc) + (fy) ] 0.00
Interaction ratio
=fc / fc_allowable 0.00
Status SAFE

Print Time/Date: 07/12/2018 20:09 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 429 of 617
Job No Sheet No Rev
BN/SS/-01 430
Part
Software licensed to BN
Job Title Design of Overhead Gantry Hoarding Truss - 30m Span Ref

By Biswajit Date06-Dec-18 Chd Biswajit


Client Suntony Signage File Final Gantry Truss-30m Date/Time
Span.std 07-Dec-2018 20:06

Design Of Member No. 206 As Per IS:800

Input Parameters

Member Section PIP1524L

2
Cross Sectional Area Ax (mm ) 0.00
rz (mm) 52.31
ry (mm) 52.31
Unsupported Length - Major Axis For Slenderness Check Lz (mm) 1500.00
Unsupported Length - Minor Axis For Slenderness Check Ly (mm) 1500.00
Yield Stress fy (MPa) 0.00
Allowable Ratio For Interaction Check 1.00

Design Forces

Axial Load Fx (N ) 0.00


Critical Loadcase No. 0

Details Of Calculation

Slenderness Checking

Lez (mm) 1500.00


Ley (mm) 1500.00
Lez / rz 28.67
Ley / ry 28.67
Actual Slenderness Ratio 28.67
Allowable Slenderness Ratio 400.00
Status SAFE

Check Against Axial Compression For Truss Member

Actual Compressive Stress fc (MPa)


=Fx / Ax 0.00

Calculation Of Allowable Compressive Stress :

Print Time/Date: 07/12/2018 20:09 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 430 of 617
Job No Sheet No Rev
BN/SS/-01 431
Part
Software licensed to BN
Job Title Design of Overhead Gantry Hoarding Truss - 30m Span Ref

By Biswajit Date06-Dec-18 Chd Biswajit


Client Suntony Signage File Final Gantry Truss-30m Date/Time
Span.std 07-Dec-2018 20:06

E (MPa) 200000.00
L/r 28.67
fcc (MPa)
2 2
=π E / λ 2401.04
Allowable Compressive Stress fc_allowable (MPa)
1.4 1.4
=0.6fccfy / [(fcc) + (fy) ] 0.00
Interaction ratio
=fc / fc_allowable 0.00
Status SAFE

Print Time/Date: 07/12/2018 20:09 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 431 of 617
Job No Sheet No Rev
BN/SS/-01 432
Part
Software licensed to BN
Job Title Design of Overhead Gantry Hoarding Truss - 30m Span Ref

By Biswajit Date06-Dec-18 Chd Biswajit


Client Suntony Signage File Final Gantry Truss-30m Date/Time
Span.std 07-Dec-2018 20:06

Design Of Member No. 207 As Per IS:800

Input Parameters

Member Section PIP1524L

2
Cross Sectional Area Ax (mm ) 0.00
rz (mm) 52.31
ry (mm) 52.31
Unsupported Length - Major Axis For Slenderness Check Lz (mm) 1000.00
Unsupported Length - Minor Axis For Slenderness Check Ly (mm) 1000.00
Yield Stress fy (MPa) 0.00
Allowable Ratio For Interaction Check 1.00

Design Forces

Axial Load Fx (N ) 0.00


Critical Loadcase No. 0

Details Of Calculation

Slenderness Checking

Lez (mm) 1000.00


Ley (mm) 1000.00
Lez / rz 19.11
Ley / ry 19.11
Actual Slenderness Ratio 19.11
Allowable Slenderness Ratio 400.00
Status SAFE

Check Against Axial Compression For Truss Member

Actual Compressive Stress fc (MPa)


=Fx / Ax 0.00

Calculation Of Allowable Compressive Stress :

Print Time/Date: 07/12/2018 20:09 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 432 of 617
Job No Sheet No Rev
BN/SS/-01 433
Part
Software licensed to BN
Job Title Design of Overhead Gantry Hoarding Truss - 30m Span Ref

By Biswajit Date06-Dec-18 Chd Biswajit


Client Suntony Signage File Final Gantry Truss-30m Date/Time
Span.std 07-Dec-2018 20:06

E (MPa) 200000.00
L/r 19.11
fcc (MPa)
2 2
=π E / λ 5402.33
Allowable Compressive Stress fc_allowable (MPa)
1.4 1.4
=0.6fccfy / [(fcc) + (fy) ] 0.00
Interaction ratio
=fc / fc_allowable 0.00
Status SAFE

Print Time/Date: 07/12/2018 20:09 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 433 of 617
Job No Sheet No Rev
BN/SS/-01 434
Part
Software licensed to BN
Job Title Design of Overhead Gantry Hoarding Truss - 30m Span Ref

By Biswajit Date06-Dec-18 Chd Biswajit


Client Suntony Signage File Final Gantry Truss-30m Date/Time
Span.std 07-Dec-2018 20:06

Design Of Member No. 208 As Per IS:800

Input Parameters

Member Section PIP1524L

2
Cross Sectional Area Ax (mm ) 0.00
rz (mm) 52.31
ry (mm) 52.31
Unsupported Length - Major Axis For Slenderness Check Lz (mm) 1500.00
Unsupported Length - Minor Axis For Slenderness Check Ly (mm) 1500.00
Yield Stress fy (MPa) 0.00
Allowable Ratio For Interaction Check 1.00

Design Forces

Axial Load Fx (N ) 0.00


Critical Loadcase No. 0

Details Of Calculation

Slenderness Checking

Lez (mm) 1500.00


Ley (mm) 1500.00
Lez / rz 28.67
Ley / ry 28.67
Actual Slenderness Ratio 28.67
Allowable Slenderness Ratio 400.00
Status SAFE

Check Against Axial Compression For Truss Member

Actual Compressive Stress fc (MPa)


=Fx / Ax 0.00

Calculation Of Allowable Compressive Stress :

Print Time/Date: 07/12/2018 20:09 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 434 of 617
Job No Sheet No Rev
BN/SS/-01 435
Part
Software licensed to BN
Job Title Design of Overhead Gantry Hoarding Truss - 30m Span Ref

By Biswajit Date06-Dec-18 Chd Biswajit


Client Suntony Signage File Final Gantry Truss-30m Date/Time
Span.std 07-Dec-2018 20:06

E (MPa) 200000.00
L/r 28.67
fcc (MPa)
2 2
=π E / λ 2401.04
Allowable Compressive Stress fc_allowable (MPa)
1.4 1.4
=0.6fccfy / [(fcc) + (fy) ] 0.00
Interaction ratio
=fc / fc_allowable 0.00
Status SAFE

Print Time/Date: 07/12/2018 20:09 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 435 of 617
Job No Sheet No Rev
BN/SS/-01 436
Part
Software licensed to BN
Job Title Design of Overhead Gantry Hoarding Truss - 30m Span Ref

By Biswajit Date06-Dec-18 Chd Biswajit


Client Suntony Signage File Final Gantry Truss-30m Date/Time
Span.std 07-Dec-2018 20:06

Design Of Member No. 209 As Per IS:800

Input Parameters

Member Section PIP1524L

2
Cross Sectional Area Ax (mm ) 0.00
rz (mm) 52.31
ry (mm) 52.31
Unsupported Length - Major Axis For Slenderness Check Lz (mm) 1000.00
Unsupported Length - Minor Axis For Slenderness Check Ly (mm) 1000.00
Yield Stress fy (MPa) 0.00
Allowable Ratio For Interaction Check 1.00

Design Forces

Axial Load Fx (N ) 0.00


Critical Loadcase No. 0

Details Of Calculation

Slenderness Checking

Lez (mm) 1000.00


Ley (mm) 1000.00
Lez / rz 19.11
Ley / ry 19.11
Actual Slenderness Ratio 19.11
Allowable Slenderness Ratio 400.00
Status SAFE

Check Against Axial Compression For Truss Member

Actual Compressive Stress fc (MPa)


=Fx / Ax 0.00

Calculation Of Allowable Compressive Stress :

Print Time/Date: 07/12/2018 20:09 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 436 of 617
Job No Sheet No Rev
BN/SS/-01 437
Part
Software licensed to BN
Job Title Design of Overhead Gantry Hoarding Truss - 30m Span Ref

By Biswajit Date06-Dec-18 Chd Biswajit


Client Suntony Signage File Final Gantry Truss-30m Date/Time
Span.std 07-Dec-2018 20:06

E (MPa) 200000.00
L/r 19.11
fcc (MPa)
2 2
=π E / λ 5402.33
Allowable Compressive Stress fc_allowable (MPa)
1.4 1.4
=0.6fccfy / [(fcc) + (fy) ] 0.00
Interaction ratio
=fc / fc_allowable 0.00
Status SAFE

Print Time/Date: 07/12/2018 20:09 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 437 of 617
Job No Sheet No Rev
BN/SS/-01 438
Part
Software licensed to BN
Job Title Design of Overhead Gantry Hoarding Truss - 30m Span Ref

By Biswajit Date06-Dec-18 Chd Biswajit


Client Suntony Signage File Final Gantry Truss-30m Date/Time
Span.std 07-Dec-2018 20:06

Design Of Member No. 210 As Per IS:800

Input Parameters

Member Section PIP1524L

2
Cross Sectional Area Ax (mm ) 0.00
rz (mm) 52.31
ry (mm) 52.31
Unsupported Length - Major Axis For Slenderness Check Lz (mm) 1000.00
Unsupported Length - Minor Axis For Slenderness Check Ly (mm) 1000.00
Yield Stress fy (MPa) 0.00
Allowable Ratio For Interaction Check 1.00

Design Forces

Axial Load Fx (N ) 0.00


Critical Loadcase No. 0

Details Of Calculation

Slenderness Checking

Lez (mm) 1000.00


Ley (mm) 1000.00
Lez / rz 19.11
Ley / ry 19.11
Actual Slenderness Ratio 19.11
Allowable Slenderness Ratio 400.00
Status SAFE

Check Against Axial Compression For Truss Member

Actual Compressive Stress fc (MPa)


=Fx / Ax 0.00

Calculation Of Allowable Compressive Stress :

Print Time/Date: 07/12/2018 20:09 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 438 of 617
Job No Sheet No Rev
BN/SS/-01 439
Part
Software licensed to BN
Job Title Design of Overhead Gantry Hoarding Truss - 30m Span Ref

By Biswajit Date06-Dec-18 Chd Biswajit


Client Suntony Signage File Final Gantry Truss-30m Date/Time
Span.std 07-Dec-2018 20:06

E (MPa) 200000.00
L/r 19.11
fcc (MPa)
2 2
=π E / λ 5402.33
Allowable Compressive Stress fc_allowable (MPa)
1.4 1.4
=0.6fccfy / [(fcc) + (fy) ] 0.00
Interaction ratio
=fc / fc_allowable 0.00
Status SAFE

Print Time/Date: 07/12/2018 20:09 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 439 of 617
Job No Sheet No Rev
BN/SS/-01 440
Part
Software licensed to BN
Job Title Design of Overhead Gantry Hoarding Truss - 30m Span Ref

By Biswajit Date06-Dec-18 Chd Biswajit


Client Suntony Signage File Final Gantry Truss-30m Date/Time
Span.std 07-Dec-2018 20:06

Design Of Member No. 211 As Per IS:800

Input Parameters

Member Section PIP1524L

2
Cross Sectional Area Ax (mm ) 0.00
rz (mm) 52.31
ry (mm) 52.31
Unsupported Length - Major Axis For Slenderness Check Lz (mm) 1500.00
Unsupported Length - Minor Axis For Slenderness Check Ly (mm) 1500.00
Yield Stress fy (MPa) 0.00
Allowable Ratio For Interaction Check 1.00

Design Forces

Axial Load Fx (N ) 0.00


Critical Loadcase No. 0

Details Of Calculation

Slenderness Checking

Lez (mm) 1500.00


Ley (mm) 1500.00
Lez / rz 28.67
Ley / ry 28.67
Actual Slenderness Ratio 28.67
Allowable Slenderness Ratio 400.00
Status SAFE

Check Against Axial Compression For Truss Member

Actual Compressive Stress fc (MPa)


=Fx / Ax 0.00

Calculation Of Allowable Compressive Stress :

Print Time/Date: 07/12/2018 20:09 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 440 of 617
Job No Sheet No Rev
BN/SS/-01 441
Part
Software licensed to BN
Job Title Design of Overhead Gantry Hoarding Truss - 30m Span Ref

By Biswajit Date06-Dec-18 Chd Biswajit


Client Suntony Signage File Final Gantry Truss-30m Date/Time
Span.std 07-Dec-2018 20:06

E (MPa) 200000.00
L/r 28.67
fcc (MPa)
2 2
=π E / λ 2401.04
Allowable Compressive Stress fc_allowable (MPa)
1.4 1.4
=0.6fccfy / [(fcc) + (fy) ] 0.00
Interaction ratio
=fc / fc_allowable 0.00
Status SAFE

Print Time/Date: 07/12/2018 20:09 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 441 of 617
Job No Sheet No Rev
BN/SS/-01 442
Part
Software licensed to BN
Job Title Design of Overhead Gantry Hoarding Truss - 30m Span Ref

By Biswajit Date06-Dec-18 Chd Biswajit


Client Suntony Signage File Final Gantry Truss-30m Date/Time
Span.std 07-Dec-2018 20:06

Design Of Member No. 212 As Per IS:800

Input Parameters

Member Section PIP1524L

2
Cross Sectional Area Ax (mm ) 0.00
rz (mm) 52.31
ry (mm) 52.31
Unsupported Length - Major Axis For Slenderness Check Lz (mm) 1000.00
Unsupported Length - Minor Axis For Slenderness Check Ly (mm) 1000.00
Yield Stress fy (MPa) 0.00
Allowable Ratio For Interaction Check 1.00

Design Forces

Axial Load Fx (N ) 0.00


Critical Loadcase No. 0

Details Of Calculation

Slenderness Checking

Lez (mm) 1000.00


Ley (mm) 1000.00
Lez / rz 19.11
Ley / ry 19.11
Actual Slenderness Ratio 19.11
Allowable Slenderness Ratio 400.00
Status SAFE

Check Against Axial Compression For Truss Member

Actual Compressive Stress fc (MPa)


=Fx / Ax 0.00

Calculation Of Allowable Compressive Stress :

Print Time/Date: 07/12/2018 20:09 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 442 of 617
Job No Sheet No Rev
BN/SS/-01 443
Part
Software licensed to BN
Job Title Design of Overhead Gantry Hoarding Truss - 30m Span Ref

By Biswajit Date06-Dec-18 Chd Biswajit


Client Suntony Signage File Final Gantry Truss-30m Date/Time
Span.std 07-Dec-2018 20:06

E (MPa) 200000.00
L/r 19.11
fcc (MPa)
2 2
=π E / λ 5402.33
Allowable Compressive Stress fc_allowable (MPa)
1.4 1.4
=0.6fccfy / [(fcc) + (fy) ] 0.00
Interaction ratio
=fc / fc_allowable 0.00
Status SAFE

Print Time/Date: 07/12/2018 20:09 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 443 of 617
Job No Sheet No Rev
BN/SS/-01 444
Part
Software licensed to BN
Job Title Design of Overhead Gantry Hoarding Truss - 30m Span Ref

By Biswajit Date06-Dec-18 Chd Biswajit


Client Suntony Signage File Final Gantry Truss-30m Date/Time
Span.std 07-Dec-2018 20:06

Design Of Member No. 213 As Per IS:800

Input Parameters

Member Section PIP1524L

2
Cross Sectional Area Ax (mm ) 0.00
rz (mm) 52.31
ry (mm) 52.31
Unsupported Length - Major Axis For Slenderness Check Lz (mm) 1500.00
Unsupported Length - Minor Axis For Slenderness Check Ly (mm) 1500.00
Yield Stress fy (MPa) 0.00
Allowable Ratio For Interaction Check 1.00

Design Forces

Axial Load Fx (N ) 0.00


Critical Loadcase No. 0

Details Of Calculation

Slenderness Checking

Lez (mm) 1500.00


Ley (mm) 1500.00
Lez / rz 28.67
Ley / ry 28.67
Actual Slenderness Ratio 28.67
Allowable Slenderness Ratio 400.00
Status SAFE

Check Against Axial Compression For Truss Member

Actual Compressive Stress fc (MPa)


=Fx / Ax 0.00

Calculation Of Allowable Compressive Stress :

Print Time/Date: 07/12/2018 20:09 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 444 of 617
Job No Sheet No Rev
BN/SS/-01 445
Part
Software licensed to BN
Job Title Design of Overhead Gantry Hoarding Truss - 30m Span Ref

By Biswajit Date06-Dec-18 Chd Biswajit


Client Suntony Signage File Final Gantry Truss-30m Date/Time
Span.std 07-Dec-2018 20:06

E (MPa) 200000.00
L/r 28.67
fcc (MPa)
2 2
=π E / λ 2401.04
Allowable Compressive Stress fc_allowable (MPa)
1.4 1.4
=0.6fccfy / [(fcc) + (fy) ] 0.00
Interaction ratio
=fc / fc_allowable 0.00
Status SAFE

Print Time/Date: 07/12/2018 20:09 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 445 of 617
Job No Sheet No Rev
BN/SS/-01 446
Part
Software licensed to BN
Job Title Design of Overhead Gantry Hoarding Truss - 30m Span Ref

By Biswajit Date06-Dec-18 Chd Biswajit


Client Suntony Signage File Final Gantry Truss-30m Date/Time
Span.std 07-Dec-2018 20:06

Design Of Member No. 214 As Per IS:800

Input Parameters

Member Section PIP1524L

2
Cross Sectional Area Ax (mm ) 0.00
rz (mm) 52.31
ry (mm) 52.31
Unsupported Length - Major Axis For Slenderness Check Lz (mm) 1000.00
Unsupported Length - Minor Axis For Slenderness Check Ly (mm) 1000.00
Yield Stress fy (MPa) 0.00
Allowable Ratio For Interaction Check 1.00

Design Forces

Axial Load Fx (N ) 0.00


Critical Loadcase No. 0

Details Of Calculation

Slenderness Checking

Lez (mm) 1000.00


Ley (mm) 1000.00
Lez / rz 19.11
Ley / ry 19.11
Actual Slenderness Ratio 19.11
Allowable Slenderness Ratio 400.00
Status SAFE

Check Against Axial Compression For Truss Member

Actual Compressive Stress fc (MPa)


=Fx / Ax 0.00

Calculation Of Allowable Compressive Stress :

Print Time/Date: 07/12/2018 20:09 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 446 of 617
Job No Sheet No Rev
BN/SS/-01 447
Part
Software licensed to BN
Job Title Design of Overhead Gantry Hoarding Truss - 30m Span Ref

By Biswajit Date06-Dec-18 Chd Biswajit


Client Suntony Signage File Final Gantry Truss-30m Date/Time
Span.std 07-Dec-2018 20:06

E (MPa) 200000.00
L/r 19.11
fcc (MPa)
2 2
=π E / λ 5402.33
Allowable Compressive Stress fc_allowable (MPa)
1.4 1.4
=0.6fccfy / [(fcc) + (fy) ] 0.00
Interaction ratio
=fc / fc_allowable 0.00
Status SAFE

Print Time/Date: 07/12/2018 20:09 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 447 of 617
Job No Sheet No Rev
BN/SS/-01 448
Part
Software licensed to BN
Job Title Design of Overhead Gantry Hoarding Truss - 30m Span Ref

By Biswajit Date06-Dec-18 Chd Biswajit


Client Suntony Signage File Final Gantry Truss-30m Date/Time
Span.std 07-Dec-2018 20:06

Design Of Member No. 215 As Per IS:800

Input Parameters

Member Section PIP1524L

2
Cross Sectional Area Ax (mm ) 0.00
rz (mm) 52.31
ry (mm) 52.31
Unsupported Length - Major Axis For Slenderness Check Lz (mm) 1500.00
Unsupported Length - Minor Axis For Slenderness Check Ly (mm) 1500.00
Yield Stress fy (MPa) 0.00
Allowable Ratio For Interaction Check 1.00

Design Forces

Axial Load Fx (N ) 0.00


Critical Loadcase No. 0

Details Of Calculation

Slenderness Checking

Lez (mm) 1500.00


Ley (mm) 1500.00
Lez / rz 28.67
Ley / ry 28.67
Actual Slenderness Ratio 28.67
Allowable Slenderness Ratio 400.00
Status SAFE

Check Against Axial Compression For Truss Member

Actual Compressive Stress fc (MPa)


=Fx / Ax 0.00

Calculation Of Allowable Compressive Stress :

Print Time/Date: 07/12/2018 20:09 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 448 of 617
Job No Sheet No Rev
BN/SS/-01 449
Part
Software licensed to BN
Job Title Design of Overhead Gantry Hoarding Truss - 30m Span Ref

By Biswajit Date06-Dec-18 Chd Biswajit


Client Suntony Signage File Final Gantry Truss-30m Date/Time
Span.std 07-Dec-2018 20:06

E (MPa) 200000.00
L/r 28.67
fcc (MPa)
2 2
=π E / λ 2401.04
Allowable Compressive Stress fc_allowable (MPa)
1.4 1.4
=0.6fccfy / [(fcc) + (fy) ] 0.00
Interaction ratio
=fc / fc_allowable 0.00
Status SAFE

Print Time/Date: 07/12/2018 20:09 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 449 of 617
Job No Sheet No Rev
BN/SS/-01 450
Part
Software licensed to BN
Job Title Design of Overhead Gantry Hoarding Truss - 30m Span Ref

By Biswajit Date06-Dec-18 Chd Biswajit


Client Suntony Signage File Final Gantry Truss-30m Date/Time
Span.std 07-Dec-2018 20:06

Design Of Member No. 216 As Per IS:800

Input Parameters

Member Section PIP1524L

2
Cross Sectional Area Ax (mm ) 2090.00
rz (mm) 52.31
ry (mm) 52.31
Unsupported Length - Major Axis For Slenderness Check Lz (mm) 1000.00
Unsupported Length - Minor Axis For Slenderness Check Ly (mm) 1000.00
Yield Stress fy (MPa) 240.00
Allowable Ratio For Interaction Check 1.00

Design Forces

Axial Load Fx (N ) 3597.39


Critical Loadcase No. 3

Details Of Calculation

Slenderness Checking

Lez (mm) 1000.00


Ley (mm) 1000.00
Lez / rz 19.11
Ley / ry 19.11
Actual Slenderness Ratio 19.11
Allowable Slenderness Ratio 180.00
Status SAFE

Check Against Axial Compression For Truss Member

Actual Compressive Stress fc (MPa)


=Fx / Ax 1.72

Calculation Of Allowable Compressive Stress :

Print Time/Date: 07/12/2018 20:09 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 450 of 617
Job No Sheet No Rev
BN/SS/-01 451
Part
Software licensed to BN
Job Title Design of Overhead Gantry Hoarding Truss - 30m Span Ref

By Biswajit Date06-Dec-18 Chd Biswajit


Client Suntony Signage File Final Gantry Truss-30m Date/Time
Span.std 07-Dec-2018 20:06

E (MPa) 200000.00
L/r 19.11
fcc (MPa)
2 2
=π E / λ 5402.33
Allowable Compressive Stress fc_allowable (MPa)
1.4 1.4
=0.6fccfy / [(fcc) + (fy) ] 142.69
Interaction ratio
=fc / fc_allowable 0.01
Status SAFE

Print Time/Date: 07/12/2018 20:09 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 451 of 617
Job No Sheet No Rev
BN/SS/-01 452
Part
Software licensed to BN
Job Title Design of Overhead Gantry Hoarding Truss - 30m Span Ref

By Biswajit Date06-Dec-18 Chd Biswajit


Client Suntony Signage File Final Gantry Truss-30m Date/Time
Span.std 07-Dec-2018 20:06

Design Of Member No. 217 As Per IS:800

Input Parameters

Member Section PIP1524L

2
Cross Sectional Area Ax (mm ) 2090.00
rz (mm) 52.31
ry (mm) 52.31
Unsupported Length - Major Axis For Slenderness Check Lz (mm) 1500.00
Unsupported Length - Minor Axis For Slenderness Check Ly (mm) 1500.00
Yield Stress fy (MPa) 240.00
Allowable Ratio For Interaction Check 1.00

Design Forces

Axial Load Fx (N ) 8326.69


Critical Loadcase No. 3

Details Of Calculation

Slenderness Checking

Lez (mm) 1500.00


Ley (mm) 1500.00
Lez / rz 28.67
Ley / ry 28.67
Actual Slenderness Ratio 28.67
Allowable Slenderness Ratio 180.00
Status SAFE

Check Against Axial Compression For Truss Member

Actual Compressive Stress fc (MPa)


=Fx / Ax 3.98

Calculation Of Allowable Compressive Stress :

Print Time/Date: 07/12/2018 20:09 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 452 of 617
Job No Sheet No Rev
BN/SS/-01 453
Part
Software licensed to BN
Job Title Design of Overhead Gantry Hoarding Truss - 30m Span Ref

By Biswajit Date06-Dec-18 Chd Biswajit


Client Suntony Signage File Final Gantry Truss-30m Date/Time
Span.std 07-Dec-2018 20:06

E (MPa) 200000.00
L/r 28.67
fcc (MPa)
2 2
=π E / λ 2401.04
Allowable Compressive Stress fc_allowable (MPa)
1.4 1.4
=0.6fccfy / [(fcc) + (fy) ] 140.04
Interaction ratio
=fc / fc_allowable 0.03
Status SAFE

Print Time/Date: 07/12/2018 20:09 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 453 of 617
Job No Sheet No Rev
BN/SS/-01 454
Part
Software licensed to BN
Job Title Design of Overhead Gantry Hoarding Truss - 30m Span Ref

By Biswajit Date06-Dec-18 Chd Biswajit


Client Suntony Signage File Final Gantry Truss-30m Date/Time
Span.std 07-Dec-2018 20:06

Design Of Member No. 218 As Per IS:800

Input Parameters

Member Section PIP1524L

2
Cross Sectional Area Ax (mm ) 2090.00
rz (mm) 52.31
ry (mm) 52.31
Unsupported Length - Major Axis For Slenderness Check Lz (mm) 1000.00
Unsupported Length - Minor Axis For Slenderness Check Ly (mm) 1000.00
Yield Stress fy (MPa) 240.00
Allowable Ratio For Interaction Check 1.00

Design Forces

Axial Load Fx (N ) 18899.81


Critical Loadcase No. 3

Details Of Calculation

Slenderness Checking

Lez (mm) 1000.00


Ley (mm) 1000.00
Lez / rz 19.11
Ley / ry 19.11
Actual Slenderness Ratio 19.11
Allowable Slenderness Ratio 180.00
Status SAFE

Check Against Axial Compression For Truss Member

Actual Compressive Stress fc (MPa)


=Fx / Ax 9.04

Calculation Of Allowable Compressive Stress :

Print Time/Date: 07/12/2018 20:09 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 454 of 617
Job No Sheet No Rev
BN/SS/-01 455
Part
Software licensed to BN
Job Title Design of Overhead Gantry Hoarding Truss - 30m Span Ref

By Biswajit Date06-Dec-18 Chd Biswajit


Client Suntony Signage File Final Gantry Truss-30m Date/Time
Span.std 07-Dec-2018 20:06

E (MPa) 200000.00
L/r 19.11
fcc (MPa)
2 2
=π E / λ 5402.33
Allowable Compressive Stress fc_allowable (MPa)
1.4 1.4
=0.6fccfy / [(fcc) + (fy) ] 142.69
Interaction ratio
=fc / fc_allowable 0.06
Status SAFE

Print Time/Date: 07/12/2018 20:09 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 455 of 617
Job No Sheet No Rev
BN/SS/-01 456
Part
Software licensed to BN
Job Title Design of Overhead Gantry Hoarding Truss - 30m Span Ref

By Biswajit Date06-Dec-18 Chd Biswajit


Client Suntony Signage File Final Gantry Truss-30m Date/Time
Span.std 07-Dec-2018 20:06

Design Of Member No. 219 As Per IS:800

Input Parameters

Member Section PIP1524L

2
Cross Sectional Area Ax (mm ) 2090.00
rz (mm) 52.31
ry (mm) 52.31
Unsupported Length - Major Axis For Slenderness Check Lz (mm) 1500.00
Unsupported Length - Minor Axis For Slenderness Check Ly (mm) 1500.00
Yield Stress fy (MPa) 240.00
Allowable Ratio For Interaction Check 1.00

Design Forces

Axial Load Fx (N ) 21324.60


Critical Loadcase No. 3

Details Of Calculation

Slenderness Checking

Lez (mm) 1500.00


Ley (mm) 1500.00
Lez / rz 28.67
Ley / ry 28.67
Actual Slenderness Ratio 28.67
Allowable Slenderness Ratio 180.00
Status SAFE

Check Against Axial Compression For Truss Member

Actual Compressive Stress fc (MPa)


=Fx / Ax 10.20

Calculation Of Allowable Compressive Stress :

Print Time/Date: 07/12/2018 20:09 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 456 of 617
Job No Sheet No Rev
BN/SS/-01 457
Part
Software licensed to BN
Job Title Design of Overhead Gantry Hoarding Truss - 30m Span Ref

By Biswajit Date06-Dec-18 Chd Biswajit


Client Suntony Signage File Final Gantry Truss-30m Date/Time
Span.std 07-Dec-2018 20:06

E (MPa) 200000.00
L/r 28.67
fcc (MPa)
2 2
=π E / λ 2401.04
Allowable Compressive Stress fc_allowable (MPa)
1.4 1.4
=0.6fccfy / [(fcc) + (fy) ] 140.04
Interaction ratio
=fc / fc_allowable 0.07
Status SAFE

Print Time/Date: 07/12/2018 20:09 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 457 of 617
Job No Sheet No Rev
BN/SS/-01 458
Part
Software licensed to BN
Job Title Design of Overhead Gantry Hoarding Truss - 30m Span Ref

By Biswajit Date06-Dec-18 Chd Biswajit


Client Suntony Signage File Final Gantry Truss-30m Date/Time
Span.std 07-Dec-2018 20:06

Design Of Member No. 220 As Per IS:800

Input Parameters

Member Section PIP1524L

2
Cross Sectional Area Ax (mm ) 2090.00
Net section factor 1.00
2
Net Effective Sectional Area Anet (mm ) 2090.00
rz (mm) 52.31
ry (mm) 52.31
Unsupported Length - Major Axis For Slenderness Check Lz (mm) 1500.00
Unsupported Length - Minor Axis For Slenderness Check Ly (mm) 1500.00
Yield Stress fy (MPa) 240.00
Allowable Ratio For Interaction Check 1.00

Design Forces

Axial Load Fx (N ) -1674.38


Critical Loadcase No. 3

Details Of Calculation

Slenderness Checking

Lez (mm) 1500.00


Ley (mm) 1500.00
Lez / rz 28.67
Ley / ry 28.67
Actual Slenderness Ratio 28.67
Allowable Slenderness Ratio 400.00
Status SAFE

Check Against Axial Tension For Truss Member

Actual Tensile Stress ft (MPa)


=Fx / Anet 0.80

Print Time/Date: 07/12/2018 20:09 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 458 of 617
Job No Sheet No Rev
BN/SS/-01 459
Part
Software licensed to BN
Job Title Design of Overhead Gantry Hoarding Truss - 30m Span Ref

By Biswajit Date06-Dec-18 Chd Biswajit


Client Suntony Signage File Final Gantry Truss-30m Date/Time
Span.std 07-Dec-2018 20:06

Allowable Tensile Stress ft_allowable (MPa)


=0.60fy 144.00
Interaction ratio
=ft / ft_allowable 0.01
Status SAFE

Print Time/Date: 07/12/2018 20:09 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 459 of 617
Job No Sheet No Rev
BN/SS/-01 460
Part
Software licensed to BN
Job Title Design of Overhead Gantry Hoarding Truss - 30m Span Ref

By Biswajit Date06-Dec-18 Chd Biswajit


Client Suntony Signage File Final Gantry Truss-30m Date/Time
Span.std 07-Dec-2018 20:06

Design Of Member No. 221 As Per IS:800

Input Parameters

Member Section PIP1524L

2
Cross Sectional Area Ax (mm ) 0.00
rz (mm) 52.31
ry (mm) 52.31
Unsupported Length - Major Axis For Slenderness Check Lz (mm) 1000.00
Unsupported Length - Minor Axis For Slenderness Check Ly (mm) 1000.00
Yield Stress fy (MPa) 0.00
Allowable Ratio For Interaction Check 1.00

Design Forces

Axial Load Fx (N ) 0.00


Critical Loadcase No. 0

Details Of Calculation

Slenderness Checking

Lez (mm) 1000.00


Ley (mm) 1000.00
Lez / rz 19.11
Ley / ry 19.11
Actual Slenderness Ratio 19.11
Allowable Slenderness Ratio 400.00
Status SAFE

Check Against Axial Compression For Truss Member

Actual Compressive Stress fc (MPa)


=Fx / Ax 0.00

Calculation Of Allowable Compressive Stress :

Print Time/Date: 07/12/2018 20:09 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 460 of 617
Job No Sheet No Rev
BN/SS/-01 461
Part
Software licensed to BN
Job Title Design of Overhead Gantry Hoarding Truss - 30m Span Ref

By Biswajit Date06-Dec-18 Chd Biswajit


Client Suntony Signage File Final Gantry Truss-30m Date/Time
Span.std 07-Dec-2018 20:06

E (MPa) 200000.00
L/r 19.11
fcc (MPa)
2 2
=π E / λ 5402.33
Allowable Compressive Stress fc_allowable (MPa)
1.4 1.4
=0.6fccfy / [(fcc) + (fy) ] 0.00
Interaction ratio
=fc / fc_allowable 0.00
Status SAFE

Print Time/Date: 07/12/2018 20:09 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 461 of 617
Job No Sheet No Rev
BN/SS/-01 462
Part
Software licensed to BN
Job Title Design of Overhead Gantry Hoarding Truss - 30m Span Ref

By Biswajit Date06-Dec-18 Chd Biswajit


Client Suntony Signage File Final Gantry Truss-30m Date/Time
Span.std 07-Dec-2018 20:06

Design Of Member No. 222 As Per IS:800

Input Parameters

Member Section PIP1524L

2
Cross Sectional Area Ax (mm ) 2090.00
rz (mm) 52.31
ry (mm) 52.31
Unsupported Length - Major Axis For Slenderness Check Lz (mm) 1500.00
Unsupported Length - Minor Axis For Slenderness Check Ly (mm) 1500.00
Yield Stress fy (MPa) 240.00
Allowable Ratio For Interaction Check 1.00

Design Forces

Axial Load Fx (N ) 7.41


Critical Loadcase No. 3

Details Of Calculation

Slenderness Checking

Lez (mm) 1500.00


Ley (mm) 1500.00
Lez / rz 28.67
Ley / ry 28.67
Actual Slenderness Ratio 28.67
Allowable Slenderness Ratio 180.00
Status SAFE

Check Against Axial Compression For Truss Member

Actual Compressive Stress fc (MPa)


=Fx / Ax 0.00

Calculation Of Allowable Compressive Stress :

Print Time/Date: 07/12/2018 20:09 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 462 of 617
Job No Sheet No Rev
BN/SS/-01 463
Part
Software licensed to BN
Job Title Design of Overhead Gantry Hoarding Truss - 30m Span Ref

By Biswajit Date06-Dec-18 Chd Biswajit


Client Suntony Signage File Final Gantry Truss-30m Date/Time
Span.std 07-Dec-2018 20:06

E (MPa) 200000.00
L/r 28.67
fcc (MPa)
2 2
=π E / λ 2401.04
Allowable Compressive Stress fc_allowable (MPa)
1.4 1.4
=0.6fccfy / [(fcc) + (fy) ] 140.04
Interaction ratio
=fc / fc_allowable 0.00
Status SAFE

Print Time/Date: 07/12/2018 20:09 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 463 of 617
Job No Sheet No Rev
BN/SS/-01 464
Part
Software licensed to BN
Job Title Design of Overhead Gantry Hoarding Truss - 30m Span Ref

By Biswajit Date06-Dec-18 Chd Biswajit


Client Suntony Signage File Final Gantry Truss-30m Date/Time
Span.std 07-Dec-2018 20:06

Design Of Member No. 223 As Per IS:800

Input Parameters

Member Section PIP1524L

2
Cross Sectional Area Ax (mm ) 0.00
rz (mm) 52.31
ry (mm) 52.31
Unsupported Length - Major Axis For Slenderness Check Lz (mm) 1000.00
Unsupported Length - Minor Axis For Slenderness Check Ly (mm) 1000.00
Yield Stress fy (MPa) 0.00
Allowable Ratio For Interaction Check 1.00

Design Forces

Axial Load Fx (N ) 0.00


Critical Loadcase No. 0

Details Of Calculation

Slenderness Checking

Lez (mm) 1000.00


Ley (mm) 1000.00
Lez / rz 19.11
Ley / ry 19.11
Actual Slenderness Ratio 19.11
Allowable Slenderness Ratio 400.00
Status SAFE

Check Against Axial Compression For Truss Member

Actual Compressive Stress fc (MPa)


=Fx / Ax 0.00

Calculation Of Allowable Compressive Stress :

Print Time/Date: 07/12/2018 20:09 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 464 of 617
Job No Sheet No Rev
BN/SS/-01 465
Part
Software licensed to BN
Job Title Design of Overhead Gantry Hoarding Truss - 30m Span Ref

By Biswajit Date06-Dec-18 Chd Biswajit


Client Suntony Signage File Final Gantry Truss-30m Date/Time
Span.std 07-Dec-2018 20:06

E (MPa) 200000.00
L/r 19.11
fcc (MPa)
2 2
=π E / λ 5402.33
Allowable Compressive Stress fc_allowable (MPa)
1.4 1.4
=0.6fccfy / [(fcc) + (fy) ] 0.00
Interaction ratio
=fc / fc_allowable 0.00
Status SAFE

Print Time/Date: 07/12/2018 20:09 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 465 of 617
Job No Sheet No Rev
BN/SS/-01 466
Part
Software licensed to BN
Job Title Design of Overhead Gantry Hoarding Truss - 30m Span Ref

By Biswajit Date06-Dec-18 Chd Biswajit


Client Suntony Signage File Final Gantry Truss-30m Date/Time
Span.std 07-Dec-2018 20:06

Design Of Member No. 224 As Per IS:800

Input Parameters

Member Section PIP1524L

2
Cross Sectional Area Ax (mm ) 0.00
rz (mm) 52.31
ry (mm) 52.31
Unsupported Length - Major Axis For Slenderness Check Lz (mm) 1500.00
Unsupported Length - Minor Axis For Slenderness Check Ly (mm) 1500.00
Yield Stress fy (MPa) 0.00
Allowable Ratio For Interaction Check 1.00

Design Forces

Axial Load Fx (N ) 0.00


Critical Loadcase No. 0

Details Of Calculation

Slenderness Checking

Lez (mm) 1500.00


Ley (mm) 1500.00
Lez / rz 28.67
Ley / ry 28.67
Actual Slenderness Ratio 28.67
Allowable Slenderness Ratio 400.00
Status SAFE

Check Against Axial Compression For Truss Member

Actual Compressive Stress fc (MPa)


=Fx / Ax 0.00

Calculation Of Allowable Compressive Stress :

Print Time/Date: 07/12/2018 20:09 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 466 of 617
Job No Sheet No Rev
BN/SS/-01 467
Part
Software licensed to BN
Job Title Design of Overhead Gantry Hoarding Truss - 30m Span Ref

By Biswajit Date06-Dec-18 Chd Biswajit


Client Suntony Signage File Final Gantry Truss-30m Date/Time
Span.std 07-Dec-2018 20:06

E (MPa) 200000.00
L/r 28.67
fcc (MPa)
2 2
=π E / λ 2401.04
Allowable Compressive Stress fc_allowable (MPa)
1.4 1.4
=0.6fccfy / [(fcc) + (fy) ] 0.00
Interaction ratio
=fc / fc_allowable 0.00
Status SAFE

Print Time/Date: 07/12/2018 20:09 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 467 of 617
Job No Sheet No Rev
BN/SS/-01 468
Part
Software licensed to BN
Job Title Design of Overhead Gantry Hoarding Truss - 30m Span Ref

By Biswajit Date06-Dec-18 Chd Biswajit


Client Suntony Signage File Final Gantry Truss-30m Date/Time
Span.std 07-Dec-2018 20:06

Design Of Member No. 225 As Per IS:800

Input Parameters

Member Section PIP1524L

2
Cross Sectional Area Ax (mm ) 0.00
rz (mm) 52.31
ry (mm) 52.31
Unsupported Length - Major Axis For Slenderness Check Lz (mm) 1000.00
Unsupported Length - Minor Axis For Slenderness Check Ly (mm) 1000.00
Yield Stress fy (MPa) 0.00
Allowable Ratio For Interaction Check 1.00

Design Forces

Axial Load Fx (N ) 0.00


Critical Loadcase No. 0

Details Of Calculation

Slenderness Checking

Lez (mm) 1000.00


Ley (mm) 1000.00
Lez / rz 19.11
Ley / ry 19.11
Actual Slenderness Ratio 19.11
Allowable Slenderness Ratio 400.00
Status SAFE

Check Against Axial Compression For Truss Member

Actual Compressive Stress fc (MPa)


=Fx / Ax 0.00

Calculation Of Allowable Compressive Stress :

Print Time/Date: 07/12/2018 20:09 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 468 of 617
Job No Sheet No Rev
BN/SS/-01 469
Part
Software licensed to BN
Job Title Design of Overhead Gantry Hoarding Truss - 30m Span Ref

By Biswajit Date06-Dec-18 Chd Biswajit


Client Suntony Signage File Final Gantry Truss-30m Date/Time
Span.std 07-Dec-2018 20:06

E (MPa) 200000.00
L/r 19.11
fcc (MPa)
2 2
=π E / λ 5402.33
Allowable Compressive Stress fc_allowable (MPa)
1.4 1.4
=0.6fccfy / [(fcc) + (fy) ] 0.00
Interaction ratio
=fc / fc_allowable 0.00
Status SAFE

Print Time/Date: 07/12/2018 20:09 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 469 of 617
Job No Sheet No Rev
BN/SS/-01 470
Part
Software licensed to BN
Job Title Design of Overhead Gantry Hoarding Truss - 30m Span Ref

By Biswajit Date06-Dec-18 Chd Biswajit


Client Suntony Signage File Final Gantry Truss-30m Date/Time
Span.std 07-Dec-2018 20:06

Design Of Member No. 226 As Per IS:800

Input Parameters

Member Section PIP1524L

2
Cross Sectional Area Ax (mm ) 0.00
rz (mm) 52.31
ry (mm) 52.31
Unsupported Length - Major Axis For Slenderness Check Lz (mm) 1500.00
Unsupported Length - Minor Axis For Slenderness Check Ly (mm) 1500.00
Yield Stress fy (MPa) 0.00
Allowable Ratio For Interaction Check 1.00

Design Forces

Axial Load Fx (N ) 0.00


Critical Loadcase No. 0

Details Of Calculation

Slenderness Checking

Lez (mm) 1500.00


Ley (mm) 1500.00
Lez / rz 28.67
Ley / ry 28.67
Actual Slenderness Ratio 28.67
Allowable Slenderness Ratio 400.00
Status SAFE

Check Against Axial Compression For Truss Member

Actual Compressive Stress fc (MPa)


=Fx / Ax 0.00

Calculation Of Allowable Compressive Stress :

Print Time/Date: 07/12/2018 20:09 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 470 of 617
Job No Sheet No Rev
BN/SS/-01 471
Part
Software licensed to BN
Job Title Design of Overhead Gantry Hoarding Truss - 30m Span Ref

By Biswajit Date06-Dec-18 Chd Biswajit


Client Suntony Signage File Final Gantry Truss-30m Date/Time
Span.std 07-Dec-2018 20:06

E (MPa) 200000.00
L/r 28.67
fcc (MPa)
2 2
=π E / λ 2401.04
Allowable Compressive Stress fc_allowable (MPa)
1.4 1.4
=0.6fccfy / [(fcc) + (fy) ] 0.00
Interaction ratio
=fc / fc_allowable 0.00
Status SAFE

Print Time/Date: 07/12/2018 20:09 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 471 of 617
Job No Sheet No Rev
BN/SS/-01 472
Part
Software licensed to BN
Job Title Design of Overhead Gantry Hoarding Truss - 30m Span Ref

By Biswajit Date06-Dec-18 Chd Biswajit


Client Suntony Signage File Final Gantry Truss-30m Date/Time
Span.std 07-Dec-2018 20:06

Design Of Member No. 227 As Per IS:800

Input Parameters

Member Section PIP1524L

2
Cross Sectional Area Ax (mm ) 0.00
rz (mm) 52.31
ry (mm) 52.31
Unsupported Length - Major Axis For Slenderness Check Lz (mm) 1000.00
Unsupported Length - Minor Axis For Slenderness Check Ly (mm) 1000.00
Yield Stress fy (MPa) 0.00
Allowable Ratio For Interaction Check 1.00

Design Forces

Axial Load Fx (N ) 0.00


Critical Loadcase No. 0

Details Of Calculation

Slenderness Checking

Lez (mm) 1000.00


Ley (mm) 1000.00
Lez / rz 19.11
Ley / ry 19.11
Actual Slenderness Ratio 19.11
Allowable Slenderness Ratio 400.00
Status SAFE

Check Against Axial Compression For Truss Member

Actual Compressive Stress fc (MPa)


=Fx / Ax 0.00

Calculation Of Allowable Compressive Stress :

Print Time/Date: 07/12/2018 20:09 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 472 of 617
Job No Sheet No Rev
BN/SS/-01 473
Part
Software licensed to BN
Job Title Design of Overhead Gantry Hoarding Truss - 30m Span Ref

By Biswajit Date06-Dec-18 Chd Biswajit


Client Suntony Signage File Final Gantry Truss-30m Date/Time
Span.std 07-Dec-2018 20:06

E (MPa) 200000.00
L/r 19.11
fcc (MPa)
2 2
=π E / λ 5402.33
Allowable Compressive Stress fc_allowable (MPa)
1.4 1.4
=0.6fccfy / [(fcc) + (fy) ] 0.00
Interaction ratio
=fc / fc_allowable 0.00
Status SAFE

Print Time/Date: 07/12/2018 20:09 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 473 of 617
Job No Sheet No Rev
BN/SS/-01 474
Part
Software licensed to BN
Job Title Design of Overhead Gantry Hoarding Truss - 30m Span Ref

By Biswajit Date06-Dec-18 Chd Biswajit


Client Suntony Signage File Final Gantry Truss-30m Date/Time
Span.std 07-Dec-2018 20:06

Design Of Member No. 228 As Per IS:800

Input Parameters

Member Section PIP1524L

2
Cross Sectional Area Ax (mm ) 0.00
rz (mm) 52.31
ry (mm) 52.31
Unsupported Length - Major Axis For Slenderness Check Lz (mm) 1500.00
Unsupported Length - Minor Axis For Slenderness Check Ly (mm) 1500.00
Yield Stress fy (MPa) 0.00
Allowable Ratio For Interaction Check 1.00

Design Forces

Axial Load Fx (N ) 0.00


Critical Loadcase No. 0

Details Of Calculation

Slenderness Checking

Lez (mm) 1500.00


Ley (mm) 1500.00
Lez / rz 28.67
Ley / ry 28.67
Actual Slenderness Ratio 28.67
Allowable Slenderness Ratio 400.00
Status SAFE

Check Against Axial Compression For Truss Member

Actual Compressive Stress fc (MPa)


=Fx / Ax 0.00

Calculation Of Allowable Compressive Stress :

Print Time/Date: 07/12/2018 20:09 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 474 of 617
Job No Sheet No Rev
BN/SS/-01 475
Part
Software licensed to BN
Job Title Design of Overhead Gantry Hoarding Truss - 30m Span Ref

By Biswajit Date06-Dec-18 Chd Biswajit


Client Suntony Signage File Final Gantry Truss-30m Date/Time
Span.std 07-Dec-2018 20:06

E (MPa) 200000.00
L/r 28.67
fcc (MPa)
2 2
=π E / λ 2401.04
Allowable Compressive Stress fc_allowable (MPa)
1.4 1.4
=0.6fccfy / [(fcc) + (fy) ] 0.00
Interaction ratio
=fc / fc_allowable 0.00
Status SAFE

Print Time/Date: 07/12/2018 20:09 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 475 of 617
Job No Sheet No Rev
BN/SS/-01 476
Part
Software licensed to BN
Job Title Design of Overhead Gantry Hoarding Truss - 30m Span Ref

By Biswajit Date06-Dec-18 Chd Biswajit


Client Suntony Signage File Final Gantry Truss-30m Date/Time
Span.std 07-Dec-2018 20:06

Design Of Member No. 229 As Per IS:800

Input Parameters

Member Section PIP1524L

2
Cross Sectional Area Ax (mm ) 0.00
rz (mm) 52.31
ry (mm) 52.31
Unsupported Length - Major Axis For Slenderness Check Lz (mm) 1000.00
Unsupported Length - Minor Axis For Slenderness Check Ly (mm) 1000.00
Yield Stress fy (MPa) 0.00
Allowable Ratio For Interaction Check 1.00

Design Forces

Axial Load Fx (N ) 0.00


Critical Loadcase No. 0

Details Of Calculation

Slenderness Checking

Lez (mm) 1000.00


Ley (mm) 1000.00
Lez / rz 19.11
Ley / ry 19.11
Actual Slenderness Ratio 19.11
Allowable Slenderness Ratio 400.00
Status SAFE

Check Against Axial Compression For Truss Member

Actual Compressive Stress fc (MPa)


=Fx / Ax 0.00

Calculation Of Allowable Compressive Stress :

Print Time/Date: 07/12/2018 20:09 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 476 of 617
Job No Sheet No Rev
BN/SS/-01 477
Part
Software licensed to BN
Job Title Design of Overhead Gantry Hoarding Truss - 30m Span Ref

By Biswajit Date06-Dec-18 Chd Biswajit


Client Suntony Signage File Final Gantry Truss-30m Date/Time
Span.std 07-Dec-2018 20:06

E (MPa) 200000.00
L/r 19.11
fcc (MPa)
2 2
=π E / λ 5402.33
Allowable Compressive Stress fc_allowable (MPa)
1.4 1.4
=0.6fccfy / [(fcc) + (fy) ] 0.00
Interaction ratio
=fc / fc_allowable 0.00
Status SAFE

Print Time/Date: 07/12/2018 20:09 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 477 of 617
Job No Sheet No Rev
BN/SS/-01 478
Part
Software licensed to BN
Job Title Design of Overhead Gantry Hoarding Truss - 30m Span Ref

By Biswajit Date06-Dec-18 Chd Biswajit


Client Suntony Signage File Final Gantry Truss-30m Date/Time
Span.std 07-Dec-2018 20:06

Design Of Member No. 230 As Per IS:800

Input Parameters

Member Section PIP1524L

2
Cross Sectional Area Ax (mm ) 0.00
rz (mm) 52.31
ry (mm) 52.31
Unsupported Length - Major Axis For Slenderness Check Lz (mm) 1500.00
Unsupported Length - Minor Axis For Slenderness Check Ly (mm) 1500.00
Yield Stress fy (MPa) 0.00
Allowable Ratio For Interaction Check 1.00

Design Forces

Axial Load Fx (N ) 0.00


Critical Loadcase No. 0

Details Of Calculation

Slenderness Checking

Lez (mm) 1500.00


Ley (mm) 1500.00
Lez / rz 28.67
Ley / ry 28.67
Actual Slenderness Ratio 28.67
Allowable Slenderness Ratio 400.00
Status SAFE

Check Against Axial Compression For Truss Member

Actual Compressive Stress fc (MPa)


=Fx / Ax 0.00

Calculation Of Allowable Compressive Stress :

Print Time/Date: 07/12/2018 20:09 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 478 of 617
Job No Sheet No Rev
BN/SS/-01 479
Part
Software licensed to BN
Job Title Design of Overhead Gantry Hoarding Truss - 30m Span Ref

By Biswajit Date06-Dec-18 Chd Biswajit


Client Suntony Signage File Final Gantry Truss-30m Date/Time
Span.std 07-Dec-2018 20:06

E (MPa) 200000.00
L/r 28.67
fcc (MPa)
2 2
=π E / λ 2401.04
Allowable Compressive Stress fc_allowable (MPa)
1.4 1.4
=0.6fccfy / [(fcc) + (fy) ] 0.00
Interaction ratio
=fc / fc_allowable 0.00
Status SAFE

Print Time/Date: 07/12/2018 20:09 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 479 of 617
Job No Sheet No Rev
BN/SS/-01 480
Part
Software licensed to BN
Job Title Design of Overhead Gantry Hoarding Truss - 30m Span Ref

By Biswajit Date06-Dec-18 Chd Biswajit


Client Suntony Signage File Final Gantry Truss-30m Date/Time
Span.std 07-Dec-2018 20:06

Design Of Member No. 231 As Per IS:800

Input Parameters

Member Section PIP1524L

2
Cross Sectional Area Ax (mm ) 0.00
rz (mm) 52.31
ry (mm) 52.31
Unsupported Length - Major Axis For Slenderness Check Lz (mm) 1000.00
Unsupported Length - Minor Axis For Slenderness Check Ly (mm) 1000.00
Yield Stress fy (MPa) 0.00
Allowable Ratio For Interaction Check 1.00

Design Forces

Axial Load Fx (N ) 0.00


Critical Loadcase No. 0

Details Of Calculation

Slenderness Checking

Lez (mm) 1000.00


Ley (mm) 1000.00
Lez / rz 19.11
Ley / ry 19.11
Actual Slenderness Ratio 19.11
Allowable Slenderness Ratio 400.00
Status SAFE

Check Against Axial Compression For Truss Member

Actual Compressive Stress fc (MPa)


=Fx / Ax 0.00

Calculation Of Allowable Compressive Stress :

Print Time/Date: 07/12/2018 20:09 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 480 of 617
Job No Sheet No Rev
BN/SS/-01 481
Part
Software licensed to BN
Job Title Design of Overhead Gantry Hoarding Truss - 30m Span Ref

By Biswajit Date06-Dec-18 Chd Biswajit


Client Suntony Signage File Final Gantry Truss-30m Date/Time
Span.std 07-Dec-2018 20:06

E (MPa) 200000.00
L/r 19.11
fcc (MPa)
2 2
=π E / λ 5402.33
Allowable Compressive Stress fc_allowable (MPa)
1.4 1.4
=0.6fccfy / [(fcc) + (fy) ] 0.00
Interaction ratio
=fc / fc_allowable 0.00
Status SAFE

Print Time/Date: 07/12/2018 20:09 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 481 of 617
Job No Sheet No Rev
BN/SS/-01 482
Part
Software licensed to BN
Job Title Design of Overhead Gantry Hoarding Truss - 30m Span Ref

By Biswajit Date06-Dec-18 Chd Biswajit


Client Suntony Signage File Final Gantry Truss-30m Date/Time
Span.std 07-Dec-2018 20:06

Design Of Member No. 232 As Per IS:800

Input Parameters

Member Section PIP1524L

2
Cross Sectional Area Ax (mm ) 0.00
rz (mm) 52.31
ry (mm) 52.31
Unsupported Length - Major Axis For Slenderness Check Lz (mm) 1500.00
Unsupported Length - Minor Axis For Slenderness Check Ly (mm) 1500.00
Yield Stress fy (MPa) 0.00
Allowable Ratio For Interaction Check 1.00

Design Forces

Axial Load Fx (N ) 0.00


Critical Loadcase No. 0

Details Of Calculation

Slenderness Checking

Lez (mm) 1500.00


Ley (mm) 1500.00
Lez / rz 28.67
Ley / ry 28.67
Actual Slenderness Ratio 28.67
Allowable Slenderness Ratio 400.00
Status SAFE

Check Against Axial Compression For Truss Member

Actual Compressive Stress fc (MPa)


=Fx / Ax 0.00

Calculation Of Allowable Compressive Stress :

Print Time/Date: 07/12/2018 20:09 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 482 of 617
Job No Sheet No Rev
BN/SS/-01 483
Part
Software licensed to BN
Job Title Design of Overhead Gantry Hoarding Truss - 30m Span Ref

By Biswajit Date06-Dec-18 Chd Biswajit


Client Suntony Signage File Final Gantry Truss-30m Date/Time
Span.std 07-Dec-2018 20:06

E (MPa) 200000.00
L/r 28.67
fcc (MPa)
2 2
=π E / λ 2401.04
Allowable Compressive Stress fc_allowable (MPa)
1.4 1.4
=0.6fccfy / [(fcc) + (fy) ] 0.00
Interaction ratio
=fc / fc_allowable 0.00
Status SAFE

Print Time/Date: 07/12/2018 20:09 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 483 of 617
Job No Sheet No Rev
BN/SS/-01 484
Part
Software licensed to BN
Job Title Design of Overhead Gantry Hoarding Truss - 30m Span Ref

By Biswajit Date06-Dec-18 Chd Biswajit


Client Suntony Signage File Final Gantry Truss-30m Date/Time
Span.std 07-Dec-2018 20:06

Design Of Member No. 233 As Per IS:800

Input Parameters

Member Section PIP1524L

2
Cross Sectional Area Ax (mm ) 0.00
rz (mm) 52.31
ry (mm) 52.31
Unsupported Length - Major Axis For Slenderness Check Lz (mm) 1000.00
Unsupported Length - Minor Axis For Slenderness Check Ly (mm) 1000.00
Yield Stress fy (MPa) 0.00
Allowable Ratio For Interaction Check 1.00

Design Forces

Axial Load Fx (N ) 0.00


Critical Loadcase No. 0

Details Of Calculation

Slenderness Checking

Lez (mm) 1000.00


Ley (mm) 1000.00
Lez / rz 19.11
Ley / ry 19.11
Actual Slenderness Ratio 19.11
Allowable Slenderness Ratio 400.00
Status SAFE

Check Against Axial Compression For Truss Member

Actual Compressive Stress fc (MPa)


=Fx / Ax 0.00

Calculation Of Allowable Compressive Stress :

Print Time/Date: 07/12/2018 20:09 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 484 of 617
Job No Sheet No Rev
BN/SS/-01 485
Part
Software licensed to BN
Job Title Design of Overhead Gantry Hoarding Truss - 30m Span Ref

By Biswajit Date06-Dec-18 Chd Biswajit


Client Suntony Signage File Final Gantry Truss-30m Date/Time
Span.std 07-Dec-2018 20:06

E (MPa) 200000.00
L/r 19.11
fcc (MPa)
2 2
=π E / λ 5402.33
Allowable Compressive Stress fc_allowable (MPa)
1.4 1.4
=0.6fccfy / [(fcc) + (fy) ] 0.00
Interaction ratio
=fc / fc_allowable 0.00
Status SAFE

Print Time/Date: 07/12/2018 20:09 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 485 of 617
Job No Sheet No Rev
BN/SS/-01 486
Part
Software licensed to BN
Job Title Design of Overhead Gantry Hoarding Truss - 30m Span Ref

By Biswajit Date06-Dec-18 Chd Biswajit


Client Suntony Signage File Final Gantry Truss-30m Date/Time
Span.std 07-Dec-2018 20:06

Design Of Member No. 234 As Per IS:800

Input Parameters

Member Section PIP1524L

2
Cross Sectional Area Ax (mm ) 0.00
rz (mm) 52.31
ry (mm) 52.31
Unsupported Length - Major Axis For Slenderness Check Lz (mm) 1500.00
Unsupported Length - Minor Axis For Slenderness Check Ly (mm) 1500.00
Yield Stress fy (MPa) 0.00
Allowable Ratio For Interaction Check 1.00

Design Forces

Axial Load Fx (N ) 0.00


Critical Loadcase No. 0

Details Of Calculation

Slenderness Checking

Lez (mm) 1500.00


Ley (mm) 1500.00
Lez / rz 28.67
Ley / ry 28.67
Actual Slenderness Ratio 28.67
Allowable Slenderness Ratio 400.00
Status SAFE

Check Against Axial Compression For Truss Member

Actual Compressive Stress fc (MPa)


=Fx / Ax 0.00

Calculation Of Allowable Compressive Stress :

Print Time/Date: 07/12/2018 20:09 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 486 of 617
Job No Sheet No Rev
BN/SS/-01 487
Part
Software licensed to BN
Job Title Design of Overhead Gantry Hoarding Truss - 30m Span Ref

By Biswajit Date06-Dec-18 Chd Biswajit


Client Suntony Signage File Final Gantry Truss-30m Date/Time
Span.std 07-Dec-2018 20:06

E (MPa) 200000.00
L/r 28.67
fcc (MPa)
2 2
=π E / λ 2401.04
Allowable Compressive Stress fc_allowable (MPa)
1.4 1.4
=0.6fccfy / [(fcc) + (fy) ] 0.00
Interaction ratio
=fc / fc_allowable 0.00
Status SAFE

Print Time/Date: 07/12/2018 20:09 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 487 of 617
Job No Sheet No Rev
BN/SS/-01 488
Part
Software licensed to BN
Job Title Design of Overhead Gantry Hoarding Truss - 30m Span Ref

By Biswajit Date06-Dec-18 Chd Biswajit


Client Suntony Signage File Final Gantry Truss-30m Date/Time
Span.std 07-Dec-2018 20:06

Design Of Member No. 235 As Per IS:800

Input Parameters

Member Section PIP1524L

2
Cross Sectional Area Ax (mm ) 0.00
rz (mm) 52.31
ry (mm) 52.31
Unsupported Length - Major Axis For Slenderness Check Lz (mm) 1000.00
Unsupported Length - Minor Axis For Slenderness Check Ly (mm) 1000.00
Yield Stress fy (MPa) 0.00
Allowable Ratio For Interaction Check 1.00

Design Forces

Axial Load Fx (N ) 0.00


Critical Loadcase No. 0

Details Of Calculation

Slenderness Checking

Lez (mm) 1000.00


Ley (mm) 1000.00
Lez / rz 19.11
Ley / ry 19.11
Actual Slenderness Ratio 19.11
Allowable Slenderness Ratio 400.00
Status SAFE

Check Against Axial Compression For Truss Member

Actual Compressive Stress fc (MPa)


=Fx / Ax 0.00

Calculation Of Allowable Compressive Stress :

Print Time/Date: 07/12/2018 20:09 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 488 of 617
Job No Sheet No Rev
BN/SS/-01 489
Part
Software licensed to BN
Job Title Design of Overhead Gantry Hoarding Truss - 30m Span Ref

By Biswajit Date06-Dec-18 Chd Biswajit


Client Suntony Signage File Final Gantry Truss-30m Date/Time
Span.std 07-Dec-2018 20:06

E (MPa) 200000.00
L/r 19.11
fcc (MPa)
2 2
=π E / λ 5402.33
Allowable Compressive Stress fc_allowable (MPa)
1.4 1.4
=0.6fccfy / [(fcc) + (fy) ] 0.00
Interaction ratio
=fc / fc_allowable 0.00
Status SAFE

Print Time/Date: 07/12/2018 20:09 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 489 of 617
Job No Sheet No Rev
BN/SS/-01 490
Part
Software licensed to BN
Job Title Design of Overhead Gantry Hoarding Truss - 30m Span Ref

By Biswajit Date06-Dec-18 Chd Biswajit


Client Suntony Signage File Final Gantry Truss-30m Date/Time
Span.std 07-Dec-2018 20:06

Design Of Member No. 236 As Per IS:800

Input Parameters

Member Section PIP1524L

2
Cross Sectional Area Ax (mm ) 0.00
rz (mm) 52.31
ry (mm) 52.31
Unsupported Length - Major Axis For Slenderness Check Lz (mm) 1500.00
Unsupported Length - Minor Axis For Slenderness Check Ly (mm) 1500.00
Yield Stress fy (MPa) 0.00
Allowable Ratio For Interaction Check 1.00

Design Forces

Axial Load Fx (N ) 0.00


Critical Loadcase No. 0

Details Of Calculation

Slenderness Checking

Lez (mm) 1500.00


Ley (mm) 1500.00
Lez / rz 28.67
Ley / ry 28.67
Actual Slenderness Ratio 28.67
Allowable Slenderness Ratio 400.00
Status SAFE

Check Against Axial Compression For Truss Member

Actual Compressive Stress fc (MPa)


=Fx / Ax 0.00

Calculation Of Allowable Compressive Stress :

Print Time/Date: 07/12/2018 20:09 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 490 of 617
Job No Sheet No Rev
BN/SS/-01 491
Part
Software licensed to BN
Job Title Design of Overhead Gantry Hoarding Truss - 30m Span Ref

By Biswajit Date06-Dec-18 Chd Biswajit


Client Suntony Signage File Final Gantry Truss-30m Date/Time
Span.std 07-Dec-2018 20:06

E (MPa) 200000.00
L/r 28.67
fcc (MPa)
2 2
=π E / λ 2401.04
Allowable Compressive Stress fc_allowable (MPa)
1.4 1.4
=0.6fccfy / [(fcc) + (fy) ] 0.00
Interaction ratio
=fc / fc_allowable 0.00
Status SAFE

Print Time/Date: 07/12/2018 20:09 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 491 of 617
Job No Sheet No Rev
BN/SS/-01 492
Part
Software licensed to BN
Job Title Design of Overhead Gantry Hoarding Truss - 30m Span Ref

By Biswajit Date06-Dec-18 Chd Biswajit


Client Suntony Signage File Final Gantry Truss-30m Date/Time
Span.std 07-Dec-2018 20:06

Design Of Member No. 237 As Per IS:800

Input Parameters

Member Section PIP1524L

2
Cross Sectional Area Ax (mm ) 2090.00
rz (mm) 52.31
ry (mm) 52.31
Unsupported Length - Major Axis For Slenderness Check Lz (mm) 1000.00
Unsupported Length - Minor Axis For Slenderness Check Ly (mm) 1000.00
Yield Stress fy (MPa) 240.00
Allowable Ratio For Interaction Check 1.00

Design Forces

Axial Load Fx (N ) 298.09


Critical Loadcase No. 3

Details Of Calculation

Slenderness Checking

Lez (mm) 1000.00


Ley (mm) 1000.00
Lez / rz 19.11
Ley / ry 19.11
Actual Slenderness Ratio 19.11
Allowable Slenderness Ratio 180.00
Status SAFE

Check Against Axial Compression For Truss Member

Actual Compressive Stress fc (MPa)


=Fx / Ax 0.14

Calculation Of Allowable Compressive Stress :

Print Time/Date: 07/12/2018 20:09 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 492 of 617
Job No Sheet No Rev
BN/SS/-01 493
Part
Software licensed to BN
Job Title Design of Overhead Gantry Hoarding Truss - 30m Span Ref

By Biswajit Date06-Dec-18 Chd Biswajit


Client Suntony Signage File Final Gantry Truss-30m Date/Time
Span.std 07-Dec-2018 20:06

E (MPa) 200000.00
L/r 19.11
fcc (MPa)
2 2
=π E / λ 5402.33
Allowable Compressive Stress fc_allowable (MPa)
1.4 1.4
=0.6fccfy / [(fcc) + (fy) ] 142.69
Interaction ratio
=fc / fc_allowable 0.00
Status SAFE

Print Time/Date: 07/12/2018 20:09 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 493 of 617
Job No Sheet No Rev
BN/SS/-01 494
Part
Software licensed to BN
Job Title Design of Overhead Gantry Hoarding Truss - 30m Span Ref

By Biswajit Date06-Dec-18 Chd Biswajit


Client Suntony Signage File Final Gantry Truss-30m Date/Time
Span.std 07-Dec-2018 20:06

Design Of Member No. 238 As Per IS:800

Input Parameters

Member Section PIP1524L

2
Cross Sectional Area Ax (mm ) 0.00
rz (mm) 52.31
ry (mm) 52.31
Unsupported Length - Major Axis For Slenderness Check Lz (mm) 1500.00
Unsupported Length - Minor Axis For Slenderness Check Ly (mm) 1500.00
Yield Stress fy (MPa) 0.00
Allowable Ratio For Interaction Check 1.00

Design Forces

Axial Load Fx (N ) 0.00


Critical Loadcase No. 0

Details Of Calculation

Slenderness Checking

Lez (mm) 1500.00


Ley (mm) 1500.00
Lez / rz 28.67
Ley / ry 28.67
Actual Slenderness Ratio 28.67
Allowable Slenderness Ratio 400.00
Status SAFE

Check Against Axial Compression For Truss Member

Actual Compressive Stress fc (MPa)


=Fx / Ax 0.00

Calculation Of Allowable Compressive Stress :

Print Time/Date: 07/12/2018 20:09 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 494 of 617
Job No Sheet No Rev
BN/SS/-01 495
Part
Software licensed to BN
Job Title Design of Overhead Gantry Hoarding Truss - 30m Span Ref

By Biswajit Date06-Dec-18 Chd Biswajit


Client Suntony Signage File Final Gantry Truss-30m Date/Time
Span.std 07-Dec-2018 20:06

E (MPa) 200000.00
L/r 28.67
fcc (MPa)
2 2
=π E / λ 2401.04
Allowable Compressive Stress fc_allowable (MPa)
1.4 1.4
=0.6fccfy / [(fcc) + (fy) ] 0.00
Interaction ratio
=fc / fc_allowable 0.00
Status SAFE

Print Time/Date: 07/12/2018 20:09 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 495 of 617
Job No Sheet No Rev
BN/SS/-01 496
Part
Software licensed to BN
Job Title Design of Overhead Gantry Hoarding Truss - 30m Span Ref

By Biswajit Date06-Dec-18 Chd Biswajit


Client Suntony Signage File Final Gantry Truss-30m Date/Time
Span.std 07-Dec-2018 20:06

Design Of Member No. 239 As Per IS:800

Input Parameters

Member Section PIP1524L

2
Cross Sectional Area Ax (mm ) 2090.00
rz (mm) 52.31
ry (mm) 52.31
Unsupported Length - Major Axis For Slenderness Check Lz (mm) 1000.00
Unsupported Length - Minor Axis For Slenderness Check Ly (mm) 1000.00
Yield Stress fy (MPa) 240.00
Allowable Ratio For Interaction Check 1.00

Design Forces

Axial Load Fx (N ) 13970.83


Critical Loadcase No. 3

Details Of Calculation

Slenderness Checking

Lez (mm) 1000.00


Ley (mm) 1000.00
Lez / rz 19.11
Ley / ry 19.11
Actual Slenderness Ratio 19.11
Allowable Slenderness Ratio 180.00
Status SAFE

Check Against Axial Compression For Truss Member

Actual Compressive Stress fc (MPa)


=Fx / Ax 6.68

Calculation Of Allowable Compressive Stress :

Print Time/Date: 07/12/2018 20:09 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 496 of 617
Job No Sheet No Rev
BN/SS/-01 497
Part
Software licensed to BN
Job Title Design of Overhead Gantry Hoarding Truss - 30m Span Ref

By Biswajit Date06-Dec-18 Chd Biswajit


Client Suntony Signage File Final Gantry Truss-30m Date/Time
Span.std 07-Dec-2018 20:06

E (MPa) 200000.00
L/r 19.11
fcc (MPa)
2 2
=π E / λ 5402.33
Allowable Compressive Stress fc_allowable (MPa)
1.4 1.4
=0.6fccfy / [(fcc) + (fy) ] 142.69
Interaction ratio
=fc / fc_allowable 0.05
Status SAFE

Print Time/Date: 07/12/2018 20:09 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 497 of 617
Job No Sheet No Rev
BN/SS/-01 498
Part
Software licensed to BN
Job Title Design of Overhead Gantry Hoarding Truss - 30m Span Ref

By Biswajit Date06-Dec-18 Chd Biswajit


Client Suntony Signage File Final Gantry Truss-30m Date/Time
Span.std 07-Dec-2018 20:06

Design Of Member No. 240 As Per IS:800

Input Parameters

Member Section PIP889L

2
Cross Sectional Area Ax (mm ) 862.00
rz (mm) 30.31
ry (mm) 30.31
Unsupported Length - Major Axis For Slenderness Check Lz (mm) 1850.29
Unsupported Length - Minor Axis For Slenderness Check Ly (mm) 1850.29
Yield Stress fy (MPa) 240.00
Allowable Ratio For Interaction Check 1.00

Design Forces

Axial Load Fx (N ) 25712.71


Critical Loadcase No. 3

Details Of Calculation

Slenderness Checking

Lez (mm) 1850.29


Ley (mm) 1850.29
Lez / rz 61.04
Ley / ry 61.04
Actual Slenderness Ratio 61.04
Allowable Slenderness Ratio 180.00
Status SAFE

Check Against Axial Compression For Truss Member

Actual Compressive Stress fc (MPa)


=Fx / Ax 29.83

Calculation Of Allowable Compressive Stress :

Print Time/Date: 07/12/2018 20:09 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 498 of 617
Job No Sheet No Rev
BN/SS/-01 499
Part
Software licensed to BN
Job Title Design of Overhead Gantry Hoarding Truss - 30m Span Ref

By Biswajit Date06-Dec-18 Chd Biswajit


Client Suntony Signage File Final Gantry Truss-30m Date/Time
Span.std 07-Dec-2018 20:06

E (MPa) 200000.00
L/r 61.04
fcc (MPa)
2 2
=π E / λ 529.74
Allowable Compressive Stress fc_allowable (MPa)
1.4 1.4
=0.6fccfy / [(fcc) + (fy) ] 117.45
Interaction ratio
=fc / fc_allowable 0.25
Status SAFE

Print Time/Date: 07/12/2018 20:09 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 499 of 617
Job No Sheet No Rev
BN/SS/-01 500
Part
Software licensed to BN
Job Title Design of Overhead Gantry Hoarding Truss - 30m Span Ref

By Biswajit Date06-Dec-18 Chd Biswajit


Client Suntony Signage File Final Gantry Truss-30m Date/Time
Span.std 07-Dec-2018 20:06

Design Of Member No. 241 As Per IS:800

Input Parameters

Member Section PIP889L

2
Cross Sectional Area Ax (mm ) 862.00
Net section factor 1.00
2
Net Effective Sectional Area Anet (mm ) 862.00
rz (mm) 30.31
ry (mm) 30.31
Unsupported Length - Major Axis For Slenderness Check Lz (mm) 1850.29
Unsupported Length - Minor Axis For Slenderness Check Ly (mm) 1850.29
Yield Stress fy (MPa) 240.00
Allowable Ratio For Interaction Check 1.00

Design Forces

Axial Load Fx (N ) -15569.88


Critical Loadcase No. 3

Details Of Calculation

Slenderness Checking

Lez (mm) 1850.29


Ley (mm) 1850.29
Lez / rz 61.04
Ley / ry 61.04
Actual Slenderness Ratio 61.04
Allowable Slenderness Ratio 400.00
Status SAFE

Check Against Axial Tension For Truss Member

Actual Tensile Stress ft (MPa)


=Fx / Anet 18.06

Print Time/Date: 07/12/2018 20:09 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 500 of 617
Job No Sheet No Rev
BN/SS/-01 501
Part
Software licensed to BN
Job Title Design of Overhead Gantry Hoarding Truss - 30m Span Ref

By Biswajit Date06-Dec-18 Chd Biswajit


Client Suntony Signage File Final Gantry Truss-30m Date/Time
Span.std 07-Dec-2018 20:06

Allowable Tensile Stress ft_allowable (MPa)


=0.60fy 144.00
Interaction ratio
=ft / ft_allowable 0.13
Status SAFE

Print Time/Date: 07/12/2018 20:09 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 501 of 617
Job No Sheet No Rev
BN/SS/-01 502
Part
Software licensed to BN
Job Title Design of Overhead Gantry Hoarding Truss - 30m Span Ref

By Biswajit Date06-Dec-18 Chd Biswajit


Client Suntony Signage File Final Gantry Truss-30m Date/Time
Span.std 07-Dec-2018 20:06

Design Of Member No. 242 As Per IS:800

Input Parameters

Member Section PIP889L

2
Cross Sectional Area Ax (mm ) 862.00
Net section factor 1.00
2
Net Effective Sectional Area Anet (mm ) 862.00
rz (mm) 30.31
ry (mm) 30.31
Unsupported Length - Major Axis For Slenderness Check Lz (mm) 1850.29
Unsupported Length - Minor Axis For Slenderness Check Ly (mm) 1850.29
Yield Stress fy (MPa) 240.00
Allowable Ratio For Interaction Check 1.00

Design Forces

Axial Load Fx (N ) -28649.10


Critical Loadcase No. 3

Details Of Calculation

Slenderness Checking

Lez (mm) 1850.29


Ley (mm) 1850.29
Lez / rz 61.04
Ley / ry 61.04
Actual Slenderness Ratio 61.04
Allowable Slenderness Ratio 400.00
Status SAFE

Check Against Axial Tension For Truss Member

Actual Tensile Stress ft (MPa)


=Fx / Anet 33.24

Print Time/Date: 07/12/2018 20:09 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 502 of 617
Job No Sheet No Rev
BN/SS/-01 503
Part
Software licensed to BN
Job Title Design of Overhead Gantry Hoarding Truss - 30m Span Ref

By Biswajit Date06-Dec-18 Chd Biswajit


Client Suntony Signage File Final Gantry Truss-30m Date/Time
Span.std 07-Dec-2018 20:06

Allowable Tensile Stress ft_allowable (MPa)


=0.60fy 144.00
Interaction ratio
=ft / ft_allowable 0.23
Status SAFE

Print Time/Date: 07/12/2018 20:09 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 503 of 617
Job No Sheet No Rev
BN/SS/-01 504
Part
Software licensed to BN
Job Title Design of Overhead Gantry Hoarding Truss - 30m Span Ref

By Biswajit Date06-Dec-18 Chd Biswajit


Client Suntony Signage File Final Gantry Truss-30m Date/Time
Span.std 07-Dec-2018 20:06

Design Of Member No. 243 As Per IS:800

Input Parameters

Member Section PIP889L

2
Cross Sectional Area Ax (mm ) 862.00
rz (mm) 30.31
ry (mm) 30.31
Unsupported Length - Major Axis For Slenderness Check Lz (mm) 1850.29
Unsupported Length - Minor Axis For Slenderness Check Ly (mm) 1850.29
Yield Stress fy (MPa) 240.00
Allowable Ratio For Interaction Check 1.00

Design Forces

Axial Load Fx (N ) 12633.50


Critical Loadcase No. 3

Details Of Calculation

Slenderness Checking

Lez (mm) 1850.29


Ley (mm) 1850.29
Lez / rz 61.04
Ley / ry 61.04
Actual Slenderness Ratio 61.04
Allowable Slenderness Ratio 180.00
Status SAFE

Check Against Axial Compression For Truss Member

Actual Compressive Stress fc (MPa)


=Fx / Ax 14.66

Calculation Of Allowable Compressive Stress :

Print Time/Date: 07/12/2018 20:09 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 504 of 617
Job No Sheet No Rev
BN/SS/-01 505
Part
Software licensed to BN
Job Title Design of Overhead Gantry Hoarding Truss - 30m Span Ref

By Biswajit Date06-Dec-18 Chd Biswajit


Client Suntony Signage File Final Gantry Truss-30m Date/Time
Span.std 07-Dec-2018 20:06

E (MPa) 200000.00
L/r 61.04
fcc (MPa)
2 2
=π E / λ 529.74
Allowable Compressive Stress fc_allowable (MPa)
1.4 1.4
=0.6fccfy / [(fcc) + (fy) ] 117.45
Interaction ratio
=fc / fc_allowable 0.12
Status SAFE

Print Time/Date: 07/12/2018 20:09 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 505 of 617
Job No Sheet No Rev
BN/SS/-01 506
Part
Software licensed to BN
Job Title Design of Overhead Gantry Hoarding Truss - 30m Span Ref

By Biswajit Date06-Dec-18 Chd Biswajit


Client Suntony Signage File Final Gantry Truss-30m Date/Time
Span.std 07-Dec-2018 20:06

Design Of Member No. 244 As Per IS:800

Input Parameters

Member Section PIP889L

2
Cross Sectional Area Ax (mm ) 862.00
rz (mm) 30.31
ry (mm) 30.31
Unsupported Length - Major Axis For Slenderness Check Lz (mm) 1850.30
Unsupported Length - Minor Axis For Slenderness Check Ly (mm) 1850.30
Yield Stress fy (MPa) 240.00
Allowable Ratio For Interaction Check 1.00

Design Forces

Axial Load Fx (N ) 41245.05


Critical Loadcase No. 3

Details Of Calculation

Slenderness Checking

Lez (mm) 1850.30


Ley (mm) 1850.30
Lez / rz 61.04
Ley / ry 61.04
Actual Slenderness Ratio 61.04
Allowable Slenderness Ratio 180.00
Status SAFE

Check Against Axial Compression For Truss Member

Actual Compressive Stress fc (MPa)


=Fx / Ax 47.85

Calculation Of Allowable Compressive Stress :

Print Time/Date: 07/12/2018 20:09 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 506 of 617
Job No Sheet No Rev
BN/SS/-01 507
Part
Software licensed to BN
Job Title Design of Overhead Gantry Hoarding Truss - 30m Span Ref

By Biswajit Date06-Dec-18 Chd Biswajit


Client Suntony Signage File Final Gantry Truss-30m Date/Time
Span.std 07-Dec-2018 20:06

E (MPa) 200000.00
L/r 61.04
fcc (MPa)
2 2
=π E / λ 529.74
Allowable Compressive Stress fc_allowable (MPa)
1.4 1.4
=0.6fccfy / [(fcc) + (fy) ] 117.45
Interaction ratio
=fc / fc_allowable 0.41
Status SAFE

Print Time/Date: 07/12/2018 20:09 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 507 of 617
Job No Sheet No Rev
BN/SS/-01 508
Part
Software licensed to BN
Job Title Design of Overhead Gantry Hoarding Truss - 30m Span Ref

By Biswajit Date06-Dec-18 Chd Biswajit


Client Suntony Signage File Final Gantry Truss-30m Date/Time
Span.std 07-Dec-2018 20:06

Design Of Member No. 245 As Per IS:800

Input Parameters

Member Section PIP889L

2
Cross Sectional Area Ax (mm ) 862.00
Net section factor 1.00
2
Net Effective Sectional Area Anet (mm ) 862.00
rz (mm) 30.31
ry (mm) 30.31
Unsupported Length - Major Axis For Slenderness Check Lz (mm) 1850.29
Unsupported Length - Minor Axis For Slenderness Check Ly (mm) 1850.29
Yield Stress fy (MPa) 240.00
Allowable Ratio For Interaction Check 1.00

Design Forces

Axial Load Fx (N ) -41244.93


Critical Loadcase No. 3

Details Of Calculation

Slenderness Checking

Lez (mm) 1850.29


Ley (mm) 1850.29
Lez / rz 61.04
Ley / ry 61.04
Actual Slenderness Ratio 61.04
Allowable Slenderness Ratio 400.00
Status SAFE

Check Against Axial Tension For Truss Member

Actual Tensile Stress ft (MPa)


=Fx / Anet 47.85

Print Time/Date: 07/12/2018 20:09 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 508 of 617
Job No Sheet No Rev
BN/SS/-01 509
Part
Software licensed to BN
Job Title Design of Overhead Gantry Hoarding Truss - 30m Span Ref

By Biswajit Date06-Dec-18 Chd Biswajit


Client Suntony Signage File Final Gantry Truss-30m Date/Time
Span.std 07-Dec-2018 20:06

Allowable Tensile Stress ft_allowable (MPa)


=0.60fy 144.00
Interaction ratio
=ft / ft_allowable 0.33
Status SAFE

Print Time/Date: 07/12/2018 20:09 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 509 of 617
Job No Sheet No Rev
BN/SS/-01 510
Part
Software licensed to BN
Job Title Design of Overhead Gantry Hoarding Truss - 30m Span Ref

By Biswajit Date06-Dec-18 Chd Biswajit


Client Suntony Signage File Final Gantry Truss-30m Date/Time
Span.std 07-Dec-2018 20:06

Design Of Member No. 246 As Per IS:800

Input Parameters

Member Section PIP889L

2
Cross Sectional Area Ax (mm ) 862.00
rz (mm) 30.31
ry (mm) 30.31
Unsupported Length - Major Axis For Slenderness Check Lz (mm) 1850.29
Unsupported Length - Minor Axis For Slenderness Check Ly (mm) 1850.29
Yield Stress fy (MPa) 240.00
Allowable Ratio For Interaction Check 1.00

Design Forces

Axial Load Fx (N ) 41244.93


Critical Loadcase No. 3

Details Of Calculation

Slenderness Checking

Lez (mm) 1850.29


Ley (mm) 1850.29
Lez / rz 61.04
Ley / ry 61.04
Actual Slenderness Ratio 61.04
Allowable Slenderness Ratio 180.00
Status SAFE

Check Against Axial Compression For Truss Member

Actual Compressive Stress fc (MPa)


=Fx / Ax 47.85

Calculation Of Allowable Compressive Stress :

Print Time/Date: 07/12/2018 20:09 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 510 of 617
Job No Sheet No Rev
BN/SS/-01 511
Part
Software licensed to BN
Job Title Design of Overhead Gantry Hoarding Truss - 30m Span Ref

By Biswajit Date06-Dec-18 Chd Biswajit


Client Suntony Signage File Final Gantry Truss-30m Date/Time
Span.std 07-Dec-2018 20:06

E (MPa) 200000.00
L/r 61.04
fcc (MPa)
2 2
=π E / λ 529.74
Allowable Compressive Stress fc_allowable (MPa)
1.4 1.4
=0.6fccfy / [(fcc) + (fy) ] 117.45
Interaction ratio
=fc / fc_allowable 0.41
Status SAFE

Print Time/Date: 07/12/2018 20:09 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 511 of 617
Job No Sheet No Rev
BN/SS/-01 512
Part
Software licensed to BN
Job Title Design of Overhead Gantry Hoarding Truss - 30m Span Ref

By Biswajit Date06-Dec-18 Chd Biswajit


Client Suntony Signage File Final Gantry Truss-30m Date/Time
Span.std 07-Dec-2018 20:06

Design Of Member No. 247 As Per IS:800

Input Parameters

Member Section PIP889L

2
Cross Sectional Area Ax (mm ) 862.00
Net section factor 1.00
2
Net Effective Sectional Area Anet (mm ) 862.00
rz (mm) 30.31
ry (mm) 30.31
Unsupported Length - Major Axis For Slenderness Check Lz (mm) 1850.30
Unsupported Length - Minor Axis For Slenderness Check Ly (mm) 1850.30
Yield Stress fy (MPa) 240.00
Allowable Ratio For Interaction Check 1.00

Design Forces

Axial Load Fx (N ) -41245.06


Critical Loadcase No. 3

Details Of Calculation

Slenderness Checking

Lez (mm) 1850.30


Ley (mm) 1850.30
Lez / rz 61.04
Ley / ry 61.04
Actual Slenderness Ratio 61.04
Allowable Slenderness Ratio 400.00
Status SAFE

Check Against Axial Tension For Truss Member

Actual Tensile Stress ft (MPa)


=Fx / Anet 47.85

Print Time/Date: 07/12/2018 20:09 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 512 of 617
Job No Sheet No Rev
BN/SS/-01 513
Part
Software licensed to BN
Job Title Design of Overhead Gantry Hoarding Truss - 30m Span Ref

By Biswajit Date06-Dec-18 Chd Biswajit


Client Suntony Signage File Final Gantry Truss-30m Date/Time
Span.std 07-Dec-2018 20:06

Allowable Tensile Stress ft_allowable (MPa)


=0.60fy 144.00
Interaction ratio
=ft / ft_allowable 0.33
Status SAFE

Print Time/Date: 07/12/2018 20:09 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 513 of 617
Job No Sheet No Rev
BN/SS/-01 514
Part
Software licensed to BN
Job Title Design of Overhead Gantry Hoarding Truss - 30m Span Ref

By Biswajit Date06-Dec-18 Chd Biswajit


Client Suntony Signage File Final Gantry Truss-30m Date/Time
Span.std 07-Dec-2018 20:06

Design Of Member No. 248 As Per IS:800

Input Parameters

Member Section PIP889L

2
Cross Sectional Area Ax (mm ) 862.00
rz (mm) 30.31
ry (mm) 30.31
Unsupported Length - Major Axis For Slenderness Check Lz (mm) 1850.30
Unsupported Length - Minor Axis For Slenderness Check Ly (mm) 1850.30
Yield Stress fy (MPa) 240.00
Allowable Ratio For Interaction Check 1.00

Design Forces

Axial Load Fx (N ) 41245.05


Critical Loadcase No. 3

Details Of Calculation

Slenderness Checking

Lez (mm) 1850.30


Ley (mm) 1850.30
Lez / rz 61.04
Ley / ry 61.04
Actual Slenderness Ratio 61.04
Allowable Slenderness Ratio 180.00
Status SAFE

Check Against Axial Compression For Truss Member

Actual Compressive Stress fc (MPa)


=Fx / Ax 47.85

Calculation Of Allowable Compressive Stress :

Print Time/Date: 07/12/2018 20:09 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 514 of 617
Job No Sheet No Rev
BN/SS/-01 515
Part
Software licensed to BN
Job Title Design of Overhead Gantry Hoarding Truss - 30m Span Ref

By Biswajit Date06-Dec-18 Chd Biswajit


Client Suntony Signage File Final Gantry Truss-30m Date/Time
Span.std 07-Dec-2018 20:06

E (MPa) 200000.00
L/r 61.04
fcc (MPa)
2 2
=π E / λ 529.74
Allowable Compressive Stress fc_allowable (MPa)
1.4 1.4
=0.6fccfy / [(fcc) + (fy) ] 117.45
Interaction ratio
=fc / fc_allowable 0.41
Status SAFE

Print Time/Date: 07/12/2018 20:09 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 515 of 617
Job No Sheet No Rev
BN/SS/-01 516
Part
Software licensed to BN
Job Title Design of Overhead Gantry Hoarding Truss - 30m Span Ref

By Biswajit Date06-Dec-18 Chd Biswajit


Client Suntony Signage File Final Gantry Truss-30m Date/Time
Span.std 07-Dec-2018 20:06

Design Of Member No. 249 As Per IS:800

Input Parameters

Member Section PIP889L

2
Cross Sectional Area Ax (mm ) 862.00
Net section factor 1.00
2
Net Effective Sectional Area Anet (mm ) 862.00
rz (mm) 30.31
ry (mm) 30.31
Unsupported Length - Major Axis For Slenderness Check Lz (mm) 1850.29
Unsupported Length - Minor Axis For Slenderness Check Ly (mm) 1850.29
Yield Stress fy (MPa) 240.00
Allowable Ratio For Interaction Check 1.00

Design Forces

Axial Load Fx (N ) -41244.93


Critical Loadcase No. 3

Details Of Calculation

Slenderness Checking

Lez (mm) 1850.29


Ley (mm) 1850.29
Lez / rz 61.04
Ley / ry 61.04
Actual Slenderness Ratio 61.04
Allowable Slenderness Ratio 400.00
Status SAFE

Check Against Axial Tension For Truss Member

Actual Tensile Stress ft (MPa)


=Fx / Anet 47.85

Print Time/Date: 07/12/2018 20:09 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 516 of 617
Job No Sheet No Rev
BN/SS/-01 517
Part
Software licensed to BN
Job Title Design of Overhead Gantry Hoarding Truss - 30m Span Ref

By Biswajit Date06-Dec-18 Chd Biswajit


Client Suntony Signage File Final Gantry Truss-30m Date/Time
Span.std 07-Dec-2018 20:06

Allowable Tensile Stress ft_allowable (MPa)


=0.60fy 144.00
Interaction ratio
=ft / ft_allowable 0.33
Status SAFE

Print Time/Date: 07/12/2018 20:09 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 517 of 617
Job No Sheet No Rev
BN/SS/-01 518
Part
Software licensed to BN
Job Title Design of Overhead Gantry Hoarding Truss - 30m Span Ref

By Biswajit Date06-Dec-18 Chd Biswajit


Client Suntony Signage File Final Gantry Truss-30m Date/Time
Span.std 07-Dec-2018 20:06

Design Of Member No. 250 As Per IS:800

Input Parameters

Member Section PIP889L

2
Cross Sectional Area Ax (mm ) 862.00
rz (mm) 30.31
ry (mm) 30.31
Unsupported Length - Major Axis For Slenderness Check Lz (mm) 1850.29
Unsupported Length - Minor Axis For Slenderness Check Ly (mm) 1850.29
Yield Stress fy (MPa) 240.00
Allowable Ratio For Interaction Check 1.00

Design Forces

Axial Load Fx (N ) 41244.93


Critical Loadcase No. 3

Details Of Calculation

Slenderness Checking

Lez (mm) 1850.29


Ley (mm) 1850.29
Lez / rz 61.04
Ley / ry 61.04
Actual Slenderness Ratio 61.04
Allowable Slenderness Ratio 180.00
Status SAFE

Check Against Axial Compression For Truss Member

Actual Compressive Stress fc (MPa)


=Fx / Ax 47.85

Calculation Of Allowable Compressive Stress :

Print Time/Date: 07/12/2018 20:09 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 518 of 617
Job No Sheet No Rev
BN/SS/-01 519
Part
Software licensed to BN
Job Title Design of Overhead Gantry Hoarding Truss - 30m Span Ref

By Biswajit Date06-Dec-18 Chd Biswajit


Client Suntony Signage File Final Gantry Truss-30m Date/Time
Span.std 07-Dec-2018 20:06

E (MPa) 200000.00
L/r 61.04
fcc (MPa)
2 2
=π E / λ 529.74
Allowable Compressive Stress fc_allowable (MPa)
1.4 1.4
=0.6fccfy / [(fcc) + (fy) ] 117.45
Interaction ratio
=fc / fc_allowable 0.41
Status SAFE

Print Time/Date: 07/12/2018 20:09 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 519 of 617
Job No Sheet No Rev
BN/SS/-01 520
Part
Software licensed to BN
Job Title Design of Overhead Gantry Hoarding Truss - 30m Span Ref

By Biswajit Date06-Dec-18 Chd Biswajit


Client Suntony Signage File Final Gantry Truss-30m Date/Time
Span.std 07-Dec-2018 20:06

Design Of Member No. 251 As Per IS:800

Input Parameters

Member Section PIP889L

2
Cross Sectional Area Ax (mm ) 862.00
Net section factor 1.00
2
Net Effective Sectional Area Anet (mm ) 862.00
rz (mm) 30.31
ry (mm) 30.31
Unsupported Length - Major Axis For Slenderness Check Lz (mm) 1850.30
Unsupported Length - Minor Axis For Slenderness Check Ly (mm) 1850.30
Yield Stress fy (MPa) 240.00
Allowable Ratio For Interaction Check 1.00

Design Forces

Axial Load Fx (N ) -41245.06


Critical Loadcase No. 3

Details Of Calculation

Slenderness Checking

Lez (mm) 1850.30


Ley (mm) 1850.30
Lez / rz 61.04
Ley / ry 61.04
Actual Slenderness Ratio 61.04
Allowable Slenderness Ratio 400.00
Status SAFE

Check Against Axial Tension For Truss Member

Actual Tensile Stress ft (MPa)


=Fx / Anet 47.85

Print Time/Date: 07/12/2018 20:09 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 520 of 617
Job No Sheet No Rev
BN/SS/-01 521
Part
Software licensed to BN
Job Title Design of Overhead Gantry Hoarding Truss - 30m Span Ref

By Biswajit Date06-Dec-18 Chd Biswajit


Client Suntony Signage File Final Gantry Truss-30m Date/Time
Span.std 07-Dec-2018 20:06

Allowable Tensile Stress ft_allowable (MPa)


=0.60fy 144.00
Interaction ratio
=ft / ft_allowable 0.33
Status SAFE

Print Time/Date: 07/12/2018 20:09 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 521 of 617
Job No Sheet No Rev
BN/SS/-01 522
Part
Software licensed to BN
Job Title Design of Overhead Gantry Hoarding Truss - 30m Span Ref

By Biswajit Date06-Dec-18 Chd Biswajit


Client Suntony Signage File Final Gantry Truss-30m Date/Time
Span.std 07-Dec-2018 20:06

Design Of Member No. 252 As Per IS:800

Input Parameters

Member Section PIP889L

2
Cross Sectional Area Ax (mm ) 862.00
rz (mm) 30.31
ry (mm) 30.31
Unsupported Length - Major Axis For Slenderness Check Lz (mm) 1850.29
Unsupported Length - Minor Axis For Slenderness Check Ly (mm) 1850.29
Yield Stress fy (MPa) 240.00
Allowable Ratio For Interaction Check 1.00

Design Forces

Axial Load Fx (N ) 2103.06


Critical Loadcase No. 3

Details Of Calculation

Slenderness Checking

Lez (mm) 1850.29


Ley (mm) 1850.29
Lez / rz 61.04
Ley / ry 61.04
Actual Slenderness Ratio 61.04
Allowable Slenderness Ratio 180.00
Status SAFE

Check Against Axial Compression For Truss Member

Actual Compressive Stress fc (MPa)


=Fx / Ax 2.44

Calculation Of Allowable Compressive Stress :

Print Time/Date: 07/12/2018 20:09 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 522 of 617
Job No Sheet No Rev
BN/SS/-01 523
Part
Software licensed to BN
Job Title Design of Overhead Gantry Hoarding Truss - 30m Span Ref

By Biswajit Date06-Dec-18 Chd Biswajit


Client Suntony Signage File Final Gantry Truss-30m Date/Time
Span.std 07-Dec-2018 20:06

E (MPa) 200000.00
L/r 61.04
fcc (MPa)
2 2
=π E / λ 529.74
Allowable Compressive Stress fc_allowable (MPa)
1.4 1.4
=0.6fccfy / [(fcc) + (fy) ] 117.45
Interaction ratio
=fc / fc_allowable 0.02
Status SAFE

Print Time/Date: 07/12/2018 20:09 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 523 of 617
Job No Sheet No Rev
BN/SS/-01 524
Part
Software licensed to BN
Job Title Design of Overhead Gantry Hoarding Truss - 30m Span Ref

By Biswajit Date06-Dec-18 Chd Biswajit


Client Suntony Signage File Final Gantry Truss-30m Date/Time
Span.std 07-Dec-2018 20:06

Design Of Member No. 253 As Per IS:800

Input Parameters

Member Section PIP889L

2
Cross Sectional Area Ax (mm ) 862.00
rz (mm) 30.31
ry (mm) 30.31
Unsupported Length - Major Axis For Slenderness Check Lz (mm) 1850.29
Unsupported Length - Minor Axis For Slenderness Check Ly (mm) 1850.29
Yield Stress fy (MPa) 240.00
Allowable Ratio For Interaction Check 1.00

Design Forces

Axial Load Fx (N ) 2103.06


Critical Loadcase No. 3

Details Of Calculation

Slenderness Checking

Lez (mm) 1850.29


Ley (mm) 1850.29
Lez / rz 61.04
Ley / ry 61.04
Actual Slenderness Ratio 61.04
Allowable Slenderness Ratio 180.00
Status SAFE

Check Against Axial Compression For Truss Member

Actual Compressive Stress fc (MPa)


=Fx / Ax 2.44

Calculation Of Allowable Compressive Stress :

Print Time/Date: 07/12/2018 20:09 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 524 of 617
Job No Sheet No Rev
BN/SS/-01 525
Part
Software licensed to BN
Job Title Design of Overhead Gantry Hoarding Truss - 30m Span Ref

By Biswajit Date06-Dec-18 Chd Biswajit


Client Suntony Signage File Final Gantry Truss-30m Date/Time
Span.std 07-Dec-2018 20:06

E (MPa) 200000.00
L/r 61.04
fcc (MPa)
2 2
=π E / λ 529.74
Allowable Compressive Stress fc_allowable (MPa)
1.4 1.4
=0.6fccfy / [(fcc) + (fy) ] 117.45
Interaction ratio
=fc / fc_allowable 0.02
Status SAFE

Print Time/Date: 07/12/2018 20:09 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 525 of 617
Job No Sheet No Rev
BN/SS/-01 526
Part
Software licensed to BN
Job Title Design of Overhead Gantry Hoarding Truss - 30m Span Ref

By Biswajit Date06-Dec-18 Chd Biswajit


Client Suntony Signage File Final Gantry Truss-30m Date/Time
Span.std 07-Dec-2018 20:06

Design Of Member No. 254 As Per IS:800

Input Parameters

Member Section PIP889L

2
Cross Sectional Area Ax (mm ) 862.00
Net section factor 1.00
2
Net Effective Sectional Area Anet (mm ) 862.00
rz (mm) 30.31
ry (mm) 30.31
Unsupported Length - Major Axis For Slenderness Check Lz (mm) 1850.29
Unsupported Length - Minor Axis For Slenderness Check Ly (mm) 1850.29
Yield Stress fy (MPa) 240.00
Allowable Ratio For Interaction Check 1.00

Design Forces

Axial Load Fx (N ) -46.81


Critical Loadcase No. 3

Details Of Calculation

Slenderness Checking

Lez (mm) 1850.29


Ley (mm) 1850.29
Lez / rz 61.04
Ley / ry 61.04
Actual Slenderness Ratio 61.04
Allowable Slenderness Ratio 180.00
Status SAFE

Check Against Axial Tension For Truss Member

Actual Tensile Stress ft (MPa)


=Fx / Anet 0.05

Print Time/Date: 07/12/2018 20:09 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 526 of 617
Job No Sheet No Rev
BN/SS/-01 527
Part
Software licensed to BN
Job Title Design of Overhead Gantry Hoarding Truss - 30m Span Ref

By Biswajit Date06-Dec-18 Chd Biswajit


Client Suntony Signage File Final Gantry Truss-30m Date/Time
Span.std 07-Dec-2018 20:06

Allowable Tensile Stress ft_allowable (MPa)


=0.60fy 144.00
Interaction ratio
=ft / ft_allowable 0.00
Status SAFE

Print Time/Date: 07/12/2018 20:09 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 527 of 617
Job No Sheet No Rev
BN/SS/-01 528
Part
Software licensed to BN
Job Title Design of Overhead Gantry Hoarding Truss - 30m Span Ref

By Biswajit Date06-Dec-18 Chd Biswajit


Client Suntony Signage File Final Gantry Truss-30m Date/Time
Span.std 07-Dec-2018 20:06

Design Of Member No. 255 As Per IS:800

Input Parameters

Member Section PIP889L

2
Cross Sectional Area Ax (mm ) 862.00
rz (mm) 30.31
ry (mm) 30.31
Unsupported Length - Major Axis For Slenderness Check Lz (mm) 1850.29
Unsupported Length - Minor Axis For Slenderness Check Ly (mm) 1850.29
Yield Stress fy (MPa) 240.00
Allowable Ratio For Interaction Check 1.00

Design Forces

Axial Load Fx (N ) -46.81


Critical Loadcase No. 3

Details Of Calculation

Slenderness Checking

Lez (mm) 1850.29


Ley (mm) 1850.29
Lez / rz 61.04
Ley / ry 61.04
Actual Slenderness Ratio 61.04
Allowable Slenderness Ratio 400.00
Status SAFE

Check Against Axial Compression For Truss Member

Actual Compressive Stress fc (MPa)


=Fx / Ax 0.00

Calculation Of Allowable Compressive Stress :

Print Time/Date: 07/12/2018 20:09 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 528 of 617
Job No Sheet No Rev
BN/SS/-01 529
Part
Software licensed to BN
Job Title Design of Overhead Gantry Hoarding Truss - 30m Span Ref

By Biswajit Date06-Dec-18 Chd Biswajit


Client Suntony Signage File Final Gantry Truss-30m Date/Time
Span.std 07-Dec-2018 20:06

E (MPa) 200000.00
L/r 61.04
fcc (MPa)
2 2
=π E / λ 529.74
Allowable Compressive Stress fc_allowable (MPa)
1.4 1.4
=0.6fccfy / [(fcc) + (fy) ] 0.00
Interaction ratio
=fc / fc_allowable 0.00
Status SAFE

Print Time/Date: 07/12/2018 20:09 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 529 of 617
Job No Sheet No Rev
BN/SS/-01 530
Part
Software licensed to BN
Job Title Design of Overhead Gantry Hoarding Truss - 30m Span Ref

By Biswajit Date06-Dec-18 Chd Biswajit


Client Suntony Signage File Final Gantry Truss-30m Date/Time
Span.std 07-Dec-2018 20:06

Design Of Member No. 256 As Per IS:800

Input Parameters

Member Section PIP889L

2
Cross Sectional Area Ax (mm ) 862.00
rz (mm) 30.31
ry (mm) 30.31
Unsupported Length - Major Axis For Slenderness Check Lz (mm) 1850.30
Unsupported Length - Minor Axis For Slenderness Check Ly (mm) 1850.30
Yield Stress fy (MPa) 240.00
Allowable Ratio For Interaction Check 1.00

Design Forces

Axial Load Fx (N ) 37.66


Critical Loadcase No. 3

Details Of Calculation

Slenderness Checking

Lez (mm) 1850.30


Ley (mm) 1850.30
Lez / rz 61.04
Ley / ry 61.04
Actual Slenderness Ratio 61.04
Allowable Slenderness Ratio 400.00
Status SAFE

Check Against Axial Compression For Truss Member

Actual Compressive Stress fc (MPa)


=Fx / Ax 0.04

Calculation Of Allowable Compressive Stress :

Print Time/Date: 07/12/2018 20:09 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 530 of 617
Job No Sheet No Rev
BN/SS/-01 531
Part
Software licensed to BN
Job Title Design of Overhead Gantry Hoarding Truss - 30m Span Ref

By Biswajit Date06-Dec-18 Chd Biswajit


Client Suntony Signage File Final Gantry Truss-30m Date/Time
Span.std 07-Dec-2018 20:06

E (MPa) 200000.00
L/r 61.04
fcc (MPa)
2 2
=π E / λ 529.74
Allowable Compressive Stress fc_allowable (MPa)
1.4 1.4
=0.6fccfy / [(fcc) + (fy) ] 117.45
Interaction ratio
=fc / fc_allowable 0.00
Status SAFE

Print Time/Date: 07/12/2018 20:09 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 531 of 617
Job No Sheet No Rev
BN/SS/-01 532
Part
Software licensed to BN
Job Title Design of Overhead Gantry Hoarding Truss - 30m Span Ref

By Biswajit Date06-Dec-18 Chd Biswajit


Client Suntony Signage File Final Gantry Truss-30m Date/Time
Span.std 07-Dec-2018 20:06

Design Of Member No. 257 As Per IS:800

Input Parameters

Member Section PIP889L

2
Cross Sectional Area Ax (mm ) 862.00
rz (mm) 30.31
ry (mm) 30.31
Unsupported Length - Major Axis For Slenderness Check Lz (mm) 1850.29
Unsupported Length - Minor Axis For Slenderness Check Ly (mm) 1850.29
Yield Stress fy (MPa) 240.00
Allowable Ratio For Interaction Check 1.00

Design Forces

Axial Load Fx (N ) 37.66


Critical Loadcase No. 3

Details Of Calculation

Slenderness Checking

Lez (mm) 1850.29


Ley (mm) 1850.29
Lez / rz 61.04
Ley / ry 61.04
Actual Slenderness Ratio 61.04
Allowable Slenderness Ratio 400.00
Status SAFE

Check Against Axial Compression For Truss Member

Actual Compressive Stress fc (MPa)


=Fx / Ax 0.04

Calculation Of Allowable Compressive Stress :

Print Time/Date: 07/12/2018 20:09 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 532 of 617
Job No Sheet No Rev
BN/SS/-01 533
Part
Software licensed to BN
Job Title Design of Overhead Gantry Hoarding Truss - 30m Span Ref

By Biswajit Date06-Dec-18 Chd Biswajit


Client Suntony Signage File Final Gantry Truss-30m Date/Time
Span.std 07-Dec-2018 20:06

E (MPa) 200000.00
L/r 61.04
fcc (MPa)
2 2
=π E / λ 529.74
Allowable Compressive Stress fc_allowable (MPa)
1.4 1.4
=0.6fccfy / [(fcc) + (fy) ] 117.45
Interaction ratio
=fc / fc_allowable 0.00
Status SAFE

Print Time/Date: 07/12/2018 20:09 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 533 of 617
Job No Sheet No Rev
BN/SS/-01 534
Part
Software licensed to BN
Job Title Design of Overhead Gantry Hoarding Truss - 30m Span Ref

By Biswajit Date06-Dec-18 Chd Biswajit


Client Suntony Signage File Final Gantry Truss-30m Date/Time
Span.std 07-Dec-2018 20:06

Design Of Member No. 258 As Per IS:800

Input Parameters

Member Section PIP889L

2
Cross Sectional Area Ax (mm ) 862.00
rz (mm) 30.31
ry (mm) 30.31
Unsupported Length - Major Axis For Slenderness Check Lz (mm) 1850.29
Unsupported Length - Minor Axis For Slenderness Check Ly (mm) 1850.29
Yield Stress fy (MPa) 240.00
Allowable Ratio For Interaction Check 1.00

Design Forces

Axial Load Fx (N ) 37.66


Critical Loadcase No. 3

Details Of Calculation

Slenderness Checking

Lez (mm) 1850.29


Ley (mm) 1850.29
Lez / rz 61.04
Ley / ry 61.04
Actual Slenderness Ratio 61.04
Allowable Slenderness Ratio 400.00
Status SAFE

Check Against Axial Compression For Truss Member

Actual Compressive Stress fc (MPa)


=Fx / Ax 0.04

Calculation Of Allowable Compressive Stress :

Print Time/Date: 07/12/2018 20:09 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 534 of 617
Job No Sheet No Rev
BN/SS/-01 535
Part
Software licensed to BN
Job Title Design of Overhead Gantry Hoarding Truss - 30m Span Ref

By Biswajit Date06-Dec-18 Chd Biswajit


Client Suntony Signage File Final Gantry Truss-30m Date/Time
Span.std 07-Dec-2018 20:06

E (MPa) 200000.00
L/r 61.04
fcc (MPa)
2 2
=π E / λ 529.74
Allowable Compressive Stress fc_allowable (MPa)
1.4 1.4
=0.6fccfy / [(fcc) + (fy) ] 117.45
Interaction ratio
=fc / fc_allowable 0.00
Status SAFE

Print Time/Date: 07/12/2018 20:09 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 535 of 617
Job No Sheet No Rev
BN/SS/-01 536
Part
Software licensed to BN
Job Title Design of Overhead Gantry Hoarding Truss - 30m Span Ref

By Biswajit Date06-Dec-18 Chd Biswajit


Client Suntony Signage File Final Gantry Truss-30m Date/Time
Span.std 07-Dec-2018 20:06

Design Of Member No. 259 As Per IS:800

Input Parameters

Member Section PIP889L

2
Cross Sectional Area Ax (mm ) 862.00
rz (mm) 30.31
ry (mm) 30.31
Unsupported Length - Major Axis For Slenderness Check Lz (mm) 1850.30
Unsupported Length - Minor Axis For Slenderness Check Ly (mm) 1850.30
Yield Stress fy (MPa) 240.00
Allowable Ratio For Interaction Check 1.00

Design Forces

Axial Load Fx (N ) 37.66


Critical Loadcase No. 3

Details Of Calculation

Slenderness Checking

Lez (mm) 1850.30


Ley (mm) 1850.30
Lez / rz 61.04
Ley / ry 61.04
Actual Slenderness Ratio 61.04
Allowable Slenderness Ratio 400.00
Status SAFE

Check Against Axial Compression For Truss Member

Actual Compressive Stress fc (MPa)


=Fx / Ax 0.04

Calculation Of Allowable Compressive Stress :

Print Time/Date: 07/12/2018 20:09 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 536 of 617
Job No Sheet No Rev
BN/SS/-01 537
Part
Software licensed to BN
Job Title Design of Overhead Gantry Hoarding Truss - 30m Span Ref

By Biswajit Date06-Dec-18 Chd Biswajit


Client Suntony Signage File Final Gantry Truss-30m Date/Time
Span.std 07-Dec-2018 20:06

E (MPa) 200000.00
L/r 61.04
fcc (MPa)
2 2
=π E / λ 529.74
Allowable Compressive Stress fc_allowable (MPa)
1.4 1.4
=0.6fccfy / [(fcc) + (fy) ] 117.45
Interaction ratio
=fc / fc_allowable 0.00
Status SAFE

Print Time/Date: 07/12/2018 20:09 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 537 of 617
Job No Sheet No Rev
BN/SS/-01 538
Part
Software licensed to BN
Job Title Design of Overhead Gantry Hoarding Truss - 30m Span Ref

By Biswajit Date06-Dec-18 Chd Biswajit


Client Suntony Signage File Final Gantry Truss-30m Date/Time
Span.std 07-Dec-2018 20:06

Design Of Member No. 260 As Per IS:800

Input Parameters

Member Section PIP889L

2
Cross Sectional Area Ax (mm ) 862.00
rz (mm) 30.31
ry (mm) 30.31
Unsupported Length - Major Axis For Slenderness Check Lz (mm) 1850.30
Unsupported Length - Minor Axis For Slenderness Check Ly (mm) 1850.30
Yield Stress fy (MPa) 240.00
Allowable Ratio For Interaction Check 1.00

Design Forces

Axial Load Fx (N ) 37.66


Critical Loadcase No. 3

Details Of Calculation

Slenderness Checking

Lez (mm) 1850.30


Ley (mm) 1850.30
Lez / rz 61.04
Ley / ry 61.04
Actual Slenderness Ratio 61.04
Allowable Slenderness Ratio 400.00
Status SAFE

Check Against Axial Compression For Truss Member

Actual Compressive Stress fc (MPa)


=Fx / Ax 0.04

Calculation Of Allowable Compressive Stress :

Print Time/Date: 07/12/2018 20:09 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 538 of 617
Job No Sheet No Rev
BN/SS/-01 539
Part
Software licensed to BN
Job Title Design of Overhead Gantry Hoarding Truss - 30m Span Ref

By Biswajit Date06-Dec-18 Chd Biswajit


Client Suntony Signage File Final Gantry Truss-30m Date/Time
Span.std 07-Dec-2018 20:06

E (MPa) 200000.00
L/r 61.04
fcc (MPa)
2 2
=π E / λ 529.74
Allowable Compressive Stress fc_allowable (MPa)
1.4 1.4
=0.6fccfy / [(fcc) + (fy) ] 117.45
Interaction ratio
=fc / fc_allowable 0.00
Status SAFE

Print Time/Date: 07/12/2018 20:09 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 539 of 617
Job No Sheet No Rev
BN/SS/-01 540
Part
Software licensed to BN
Job Title Design of Overhead Gantry Hoarding Truss - 30m Span Ref

By Biswajit Date06-Dec-18 Chd Biswajit


Client Suntony Signage File Final Gantry Truss-30m Date/Time
Span.std 07-Dec-2018 20:06

Design Of Member No. 261 As Per IS:800

Input Parameters

Member Section PIP889L

2
Cross Sectional Area Ax (mm ) 862.00
rz (mm) 30.31
ry (mm) 30.31
Unsupported Length - Major Axis For Slenderness Check Lz (mm) 1850.29
Unsupported Length - Minor Axis For Slenderness Check Ly (mm) 1850.29
Yield Stress fy (MPa) 240.00
Allowable Ratio For Interaction Check 1.00

Design Forces

Axial Load Fx (N ) 37.66


Critical Loadcase No. 3

Details Of Calculation

Slenderness Checking

Lez (mm) 1850.29


Ley (mm) 1850.29
Lez / rz 61.04
Ley / ry 61.04
Actual Slenderness Ratio 61.04
Allowable Slenderness Ratio 400.00
Status SAFE

Check Against Axial Compression For Truss Member

Actual Compressive Stress fc (MPa)


=Fx / Ax 0.04

Calculation Of Allowable Compressive Stress :

Print Time/Date: 07/12/2018 20:09 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 540 of 617
Job No Sheet No Rev
BN/SS/-01 541
Part
Software licensed to BN
Job Title Design of Overhead Gantry Hoarding Truss - 30m Span Ref

By Biswajit Date06-Dec-18 Chd Biswajit


Client Suntony Signage File Final Gantry Truss-30m Date/Time
Span.std 07-Dec-2018 20:06

E (MPa) 200000.00
L/r 61.04
fcc (MPa)
2 2
=π E / λ 529.74
Allowable Compressive Stress fc_allowable (MPa)
1.4 1.4
=0.6fccfy / [(fcc) + (fy) ] 117.45
Interaction ratio
=fc / fc_allowable 0.00
Status SAFE

Print Time/Date: 07/12/2018 20:09 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 541 of 617
Job No Sheet No Rev
BN/SS/-01 542
Part
Software licensed to BN
Job Title Design of Overhead Gantry Hoarding Truss - 30m Span Ref

By Biswajit Date06-Dec-18 Chd Biswajit


Client Suntony Signage File Final Gantry Truss-30m Date/Time
Span.std 07-Dec-2018 20:06

Design Of Member No. 262 As Per IS:800

Input Parameters

Member Section PIP889L

2
Cross Sectional Area Ax (mm ) 862.00
rz (mm) 30.31
ry (mm) 30.31
Unsupported Length - Major Axis For Slenderness Check Lz (mm) 1850.29
Unsupported Length - Minor Axis For Slenderness Check Ly (mm) 1850.29
Yield Stress fy (MPa) 240.00
Allowable Ratio For Interaction Check 1.00

Design Forces

Axial Load Fx (N ) 37.66


Critical Loadcase No. 3

Details Of Calculation

Slenderness Checking

Lez (mm) 1850.29


Ley (mm) 1850.29
Lez / rz 61.04
Ley / ry 61.04
Actual Slenderness Ratio 61.04
Allowable Slenderness Ratio 400.00
Status SAFE

Check Against Axial Compression For Truss Member

Actual Compressive Stress fc (MPa)


=Fx / Ax 0.04

Calculation Of Allowable Compressive Stress :

Print Time/Date: 07/12/2018 20:09 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 542 of 617
Job No Sheet No Rev
BN/SS/-01 543
Part
Software licensed to BN
Job Title Design of Overhead Gantry Hoarding Truss - 30m Span Ref

By Biswajit Date06-Dec-18 Chd Biswajit


Client Suntony Signage File Final Gantry Truss-30m Date/Time
Span.std 07-Dec-2018 20:06

E (MPa) 200000.00
L/r 61.04
fcc (MPa)
2 2
=π E / λ 529.74
Allowable Compressive Stress fc_allowable (MPa)
1.4 1.4
=0.6fccfy / [(fcc) + (fy) ] 117.45
Interaction ratio
=fc / fc_allowable 0.00
Status SAFE

Print Time/Date: 07/12/2018 20:09 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 543 of 617
Job No Sheet No Rev
BN/SS/-01 544
Part
Software licensed to BN
Job Title Design of Overhead Gantry Hoarding Truss - 30m Span Ref

By Biswajit Date06-Dec-18 Chd Biswajit


Client Suntony Signage File Final Gantry Truss-30m Date/Time
Span.std 07-Dec-2018 20:06

Design Of Member No. 263 As Per IS:800

Input Parameters

Member Section PIP889L

2
Cross Sectional Area Ax (mm ) 862.00
rz (mm) 30.31
ry (mm) 30.31
Unsupported Length - Major Axis For Slenderness Check Lz (mm) 1850.30
Unsupported Length - Minor Axis For Slenderness Check Ly (mm) 1850.30
Yield Stress fy (MPa) 240.00
Allowable Ratio For Interaction Check 1.00

Design Forces

Axial Load Fx (N ) 37.66


Critical Loadcase No. 3

Details Of Calculation

Slenderness Checking

Lez (mm) 1850.30


Ley (mm) 1850.30
Lez / rz 61.04
Ley / ry 61.04
Actual Slenderness Ratio 61.04
Allowable Slenderness Ratio 400.00
Status SAFE

Check Against Axial Compression For Truss Member

Actual Compressive Stress fc (MPa)


=Fx / Ax 0.04

Calculation Of Allowable Compressive Stress :

Print Time/Date: 07/12/2018 20:09 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 544 of 617
Job No Sheet No Rev
BN/SS/-01 545
Part
Software licensed to BN
Job Title Design of Overhead Gantry Hoarding Truss - 30m Span Ref

By Biswajit Date06-Dec-18 Chd Biswajit


Client Suntony Signage File Final Gantry Truss-30m Date/Time
Span.std 07-Dec-2018 20:06

E (MPa) 200000.00
L/r 61.04
fcc (MPa)
2 2
=π E / λ 529.74
Allowable Compressive Stress fc_allowable (MPa)
1.4 1.4
=0.6fccfy / [(fcc) + (fy) ] 117.45
Interaction ratio
=fc / fc_allowable 0.00
Status SAFE

Print Time/Date: 07/12/2018 20:09 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 545 of 617
Job No Sheet No Rev
BN/SS/-01 546
Part
Software licensed to BN
Job Title Design of Overhead Gantry Hoarding Truss - 30m Span Ref

By Biswajit Date06-Dec-18 Chd Biswajit


Client Suntony Signage File Final Gantry Truss-30m Date/Time
Span.std 07-Dec-2018 20:06

Design Of Member No. 264 As Per IS:800

Input Parameters

Member Section PIP889L

2
Cross Sectional Area Ax (mm ) 862.00
Net section factor 1.00
2
Net Effective Sectional Area Anet (mm ) 862.00
rz (mm) 30.31
ry (mm) 30.31
Unsupported Length - Major Axis For Slenderness Check Lz (mm) 1474.31
Unsupported Length - Minor Axis For Slenderness Check Ly (mm) 1474.31
Yield Stress fy (MPa) 240.00
Allowable Ratio For Interaction Check 1.00

Design Forces

Axial Load Fx (N ) -10543.86


Critical Loadcase No. 3

Details Of Calculation

Slenderness Checking

Lez (mm) 1474.31


Ley (mm) 1474.31
Lez / rz 48.64
Ley / ry 48.64
Actual Slenderness Ratio 48.64
Allowable Slenderness Ratio 400.00
Status SAFE

Check Against Axial Tension For Truss Member

Actual Tensile Stress ft (MPa)


=Fx / Anet 12.23

Print Time/Date: 07/12/2018 20:09 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 546 of 617
Job No Sheet No Rev
BN/SS/-01 547
Part
Software licensed to BN
Job Title Design of Overhead Gantry Hoarding Truss - 30m Span Ref

By Biswajit Date06-Dec-18 Chd Biswajit


Client Suntony Signage File Final Gantry Truss-30m Date/Time
Span.std 07-Dec-2018 20:06

Allowable Tensile Stress ft_allowable (MPa)


=0.60fy 144.00
Interaction ratio
=ft / ft_allowable 0.08
Status SAFE

Print Time/Date: 07/12/2018 20:09 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 547 of 617
Job No Sheet No Rev
BN/SS/-01 548
Part
Software licensed to BN
Job Title Design of Overhead Gantry Hoarding Truss - 30m Span Ref

By Biswajit Date06-Dec-18 Chd Biswajit


Client Suntony Signage File Final Gantry Truss-30m Date/Time
Span.std 07-Dec-2018 20:06

Design Of Member No. 265 As Per IS:800

Input Parameters

Member Section PIP889L

2
Cross Sectional Area Ax (mm ) 862.00
rz (mm) 30.31
ry (mm) 30.31
Unsupported Length - Major Axis For Slenderness Check Lz (mm) 1474.32
Unsupported Length - Minor Axis For Slenderness Check Ly (mm) 1474.32
Yield Stress fy (MPa) 240.00
Allowable Ratio For Interaction Check 1.00

Design Forces

Axial Load Fx (N ) 10543.91


Critical Loadcase No. 3

Details Of Calculation

Slenderness Checking

Lez (mm) 1474.32


Ley (mm) 1474.32
Lez / rz 48.64
Ley / ry 48.64
Actual Slenderness Ratio 48.64
Allowable Slenderness Ratio 180.00
Status SAFE

Check Against Axial Compression For Truss Member

Actual Compressive Stress fc (MPa)


=Fx / Ax 12.23

Calculation Of Allowable Compressive Stress :

Print Time/Date: 07/12/2018 20:09 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 548 of 617
Job No Sheet No Rev
BN/SS/-01 549
Part
Software licensed to BN
Job Title Design of Overhead Gantry Hoarding Truss - 30m Span Ref

By Biswajit Date06-Dec-18 Chd Biswajit


Client Suntony Signage File Final Gantry Truss-30m Date/Time
Span.std 07-Dec-2018 20:06

E (MPa) 200000.00
L/r 48.64
fcc (MPa)
2 2
=π E / λ 834.38
Allowable Compressive Stress fc_allowable (MPa)
1.4 1.4
=0.6fccfy / [(fcc) + (fy) ] 128.35
Interaction ratio
=fc / fc_allowable 0.10
Status SAFE

Print Time/Date: 07/12/2018 20:09 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 549 of 617
Job No Sheet No Rev
BN/SS/-01 550
Part
Software licensed to BN
Job Title Design of Overhead Gantry Hoarding Truss - 30m Span Ref

By Biswajit Date06-Dec-18 Chd Biswajit


Client Suntony Signage File Final Gantry Truss-30m Date/Time
Span.std 07-Dec-2018 20:06

Design Of Member No. 266 As Per IS:800

Input Parameters

Member Section PIP889L

2
Cross Sectional Area Ax (mm ) 862.00
Net section factor 1.00
2
Net Effective Sectional Area Anet (mm ) 862.00
rz (mm) 30.31
ry (mm) 30.31
Unsupported Length - Major Axis For Slenderness Check Lz (mm) 1474.31
Unsupported Length - Minor Axis For Slenderness Check Ly (mm) 1474.31
Yield Stress fy (MPa) 240.00
Allowable Ratio For Interaction Check 1.00

Design Forces

Axial Load Fx (N ) -10543.86


Critical Loadcase No. 3

Details Of Calculation

Slenderness Checking

Lez (mm) 1474.31


Ley (mm) 1474.31
Lez / rz 48.64
Ley / ry 48.64
Actual Slenderness Ratio 48.64
Allowable Slenderness Ratio 400.00
Status SAFE

Check Against Axial Tension For Truss Member

Actual Tensile Stress ft (MPa)


=Fx / Anet 12.23

Print Time/Date: 07/12/2018 20:09 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 550 of 617
Job No Sheet No Rev
BN/SS/-01 551
Part
Software licensed to BN
Job Title Design of Overhead Gantry Hoarding Truss - 30m Span Ref

By Biswajit Date06-Dec-18 Chd Biswajit


Client Suntony Signage File Final Gantry Truss-30m Date/Time
Span.std 07-Dec-2018 20:06

Allowable Tensile Stress ft_allowable (MPa)


=0.60fy 144.00
Interaction ratio
=ft / ft_allowable 0.08
Status SAFE

Print Time/Date: 07/12/2018 20:09 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 551 of 617
Job No Sheet No Rev
BN/SS/-01 552
Part
Software licensed to BN
Job Title Design of Overhead Gantry Hoarding Truss - 30m Span Ref

By Biswajit Date06-Dec-18 Chd Biswajit


Client Suntony Signage File Final Gantry Truss-30m Date/Time
Span.std 07-Dec-2018 20:06

Design Of Member No. 267 As Per IS:800

Input Parameters

Member Section PIP889L

2
Cross Sectional Area Ax (mm ) 862.00
rz (mm) 30.31
ry (mm) 30.31
Unsupported Length - Major Axis For Slenderness Check Lz (mm) 1474.31
Unsupported Length - Minor Axis For Slenderness Check Ly (mm) 1474.31
Yield Stress fy (MPa) 240.00
Allowable Ratio For Interaction Check 1.00

Design Forces

Axial Load Fx (N ) 10543.86


Critical Loadcase No. 3

Details Of Calculation

Slenderness Checking

Lez (mm) 1474.31


Ley (mm) 1474.31
Lez / rz 48.64
Ley / ry 48.64
Actual Slenderness Ratio 48.64
Allowable Slenderness Ratio 180.00
Status SAFE

Check Against Axial Compression For Truss Member

Actual Compressive Stress fc (MPa)


=Fx / Ax 12.23

Calculation Of Allowable Compressive Stress :

Print Time/Date: 07/12/2018 20:09 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 552 of 617
Job No Sheet No Rev
BN/SS/-01 553
Part
Software licensed to BN
Job Title Design of Overhead Gantry Hoarding Truss - 30m Span Ref

By Biswajit Date06-Dec-18 Chd Biswajit


Client Suntony Signage File Final Gantry Truss-30m Date/Time
Span.std 07-Dec-2018 20:06

E (MPa) 200000.00
L/r 48.64
fcc (MPa)
2 2
=π E / λ 834.39
Allowable Compressive Stress fc_allowable (MPa)
1.4 1.4
=0.6fccfy / [(fcc) + (fy) ] 128.35
Interaction ratio
=fc / fc_allowable 0.10
Status SAFE

Print Time/Date: 07/12/2018 20:09 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 553 of 617
Job No Sheet No Rev
BN/SS/-01 554
Part
Software licensed to BN
Job Title Design of Overhead Gantry Hoarding Truss - 30m Span Ref

By Biswajit Date06-Dec-18 Chd Biswajit


Client Suntony Signage File Final Gantry Truss-30m Date/Time
Span.std 07-Dec-2018 20:06

Design Of Member No. 268 As Per IS:800

Input Parameters

Member Section PIP889L

2
Cross Sectional Area Ax (mm ) 862.00
Net section factor 1.00
2
Net Effective Sectional Area Anet (mm ) 862.00
rz (mm) 30.31
ry (mm) 30.31
Unsupported Length - Major Axis For Slenderness Check Lz (mm) 1474.32
Unsupported Length - Minor Axis For Slenderness Check Ly (mm) 1474.32
Yield Stress fy (MPa) 240.00
Allowable Ratio For Interaction Check 1.00

Design Forces

Axial Load Fx (N ) -10543.91


Critical Loadcase No. 3

Details Of Calculation

Slenderness Checking

Lez (mm) 1474.32


Ley (mm) 1474.32
Lez / rz 48.64
Ley / ry 48.64
Actual Slenderness Ratio 48.64
Allowable Slenderness Ratio 400.00
Status SAFE

Check Against Axial Tension For Truss Member

Actual Tensile Stress ft (MPa)


=Fx / Anet 12.23

Print Time/Date: 07/12/2018 20:09 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 554 of 617
Job No Sheet No Rev
BN/SS/-01 555
Part
Software licensed to BN
Job Title Design of Overhead Gantry Hoarding Truss - 30m Span Ref

By Biswajit Date06-Dec-18 Chd Biswajit


Client Suntony Signage File Final Gantry Truss-30m Date/Time
Span.std 07-Dec-2018 20:06

Allowable Tensile Stress ft_allowable (MPa)


=0.60fy 144.00
Interaction ratio
=ft / ft_allowable 0.08
Status SAFE

Print Time/Date: 07/12/2018 20:09 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 555 of 617
Job No Sheet No Rev
BN/SS/-01 556
Part
Software licensed to BN
Job Title Design of Overhead Gantry Hoarding Truss - 30m Span Ref

By Biswajit Date06-Dec-18 Chd Biswajit


Client Suntony Signage File Final Gantry Truss-30m Date/Time
Span.std 07-Dec-2018 20:06

Design Of Member No. 269 As Per IS:800

Input Parameters

Member Section PIP889L

2
Cross Sectional Area Ax (mm ) 862.00
Net section factor 1.00
2
Net Effective Sectional Area Anet (mm ) 862.00
rz (mm) 30.31
ry (mm) 30.31
Unsupported Length - Major Axis For Slenderness Check Lz (mm) 1474.31
Unsupported Length - Minor Axis For Slenderness Check Ly (mm) 1474.31
Yield Stress fy (MPa) 240.00
Allowable Ratio For Interaction Check 1.00

Design Forces

Axial Load Fx (N ) -62066.82


Critical Loadcase No. 3

Details Of Calculation

Slenderness Checking

Lez (mm) 1474.31


Ley (mm) 1474.31
Lez / rz 48.64
Ley / ry 48.64
Actual Slenderness Ratio 48.64
Allowable Slenderness Ratio 400.00
Status SAFE

Check Against Axial Tension For Truss Member

Actual Tensile Stress ft (MPa)


=Fx / Anet 72.00

Print Time/Date: 07/12/2018 20:09 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 556 of 617
Job No Sheet No Rev
BN/SS/-01 557
Part
Software licensed to BN
Job Title Design of Overhead Gantry Hoarding Truss - 30m Span Ref

By Biswajit Date06-Dec-18 Chd Biswajit


Client Suntony Signage File Final Gantry Truss-30m Date/Time
Span.std 07-Dec-2018 20:06

Allowable Tensile Stress ft_allowable (MPa)


=0.60fy 144.00
Interaction ratio
=ft / ft_allowable 0.50
Status SAFE

Print Time/Date: 07/12/2018 20:09 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 557 of 617
Job No Sheet No Rev
BN/SS/-01 558
Part
Software licensed to BN
Job Title Design of Overhead Gantry Hoarding Truss - 30m Span Ref

By Biswajit Date06-Dec-18 Chd Biswajit


Client Suntony Signage File Final Gantry Truss-30m Date/Time
Span.std 07-Dec-2018 20:06

Design Of Member No. 270 As Per IS:800

Input Parameters

Member Section PIP889L

2
Cross Sectional Area Ax (mm ) 862.00
rz (mm) 30.31
ry (mm) 30.31
Unsupported Length - Major Axis For Slenderness Check Lz (mm) 1474.32
Unsupported Length - Minor Axis For Slenderness Check Ly (mm) 1474.32
Yield Stress fy (MPa) 240.00
Allowable Ratio For Interaction Check 1.00

Design Forces

Axial Load Fx (N ) 62067.11


Critical Loadcase No. 3

Details Of Calculation

Slenderness Checking

Lez (mm) 1474.32


Ley (mm) 1474.32
Lez / rz 48.64
Ley / ry 48.64
Actual Slenderness Ratio 48.64
Allowable Slenderness Ratio 180.00
Status SAFE

Check Against Axial Compression For Truss Member

Actual Compressive Stress fc (MPa)


=Fx / Ax 72.00

Calculation Of Allowable Compressive Stress :

Print Time/Date: 07/12/2018 20:09 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 558 of 617
Job No Sheet No Rev
BN/SS/-01 559
Part
Software licensed to BN
Job Title Design of Overhead Gantry Hoarding Truss - 30m Span Ref

By Biswajit Date06-Dec-18 Chd Biswajit


Client Suntony Signage File Final Gantry Truss-30m Date/Time
Span.std 07-Dec-2018 20:06

E (MPa) 200000.00
L/r 48.64
fcc (MPa)
2 2
=π E / λ 834.38
Allowable Compressive Stress fc_allowable (MPa)
1.4 1.4
=0.6fccfy / [(fcc) + (fy) ] 128.35
Interaction ratio
=fc / fc_allowable 0.56
Status SAFE

Print Time/Date: 07/12/2018 20:09 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 559 of 617
Job No Sheet No Rev
BN/SS/-01 560
Part
Software licensed to BN
Job Title Design of Overhead Gantry Hoarding Truss - 30m Span Ref

By Biswajit Date06-Dec-18 Chd Biswajit


Client Suntony Signage File Final Gantry Truss-30m Date/Time
Span.std 07-Dec-2018 20:06

Design Of Member No. 271 As Per IS:800

Input Parameters

Member Section PIP889L

2
Cross Sectional Area Ax (mm ) 862.00
Net section factor 1.00
2
Net Effective Sectional Area Anet (mm ) 862.00
rz (mm) 30.31
ry (mm) 30.31
Unsupported Length - Major Axis For Slenderness Check Lz (mm) 1474.31
Unsupported Length - Minor Axis For Slenderness Check Ly (mm) 1474.31
Yield Stress fy (MPa) 240.00
Allowable Ratio For Interaction Check 1.00

Design Forces

Axial Load Fx (N ) -62066.82


Critical Loadcase No. 3

Details Of Calculation

Slenderness Checking

Lez (mm) 1474.31


Ley (mm) 1474.31
Lez / rz 48.64
Ley / ry 48.64
Actual Slenderness Ratio 48.64
Allowable Slenderness Ratio 400.00
Status SAFE

Check Against Axial Tension For Truss Member

Actual Tensile Stress ft (MPa)


=Fx / Anet 72.00

Print Time/Date: 07/12/2018 20:09 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 560 of 617
Job No Sheet No Rev
BN/SS/-01 561
Part
Software licensed to BN
Job Title Design of Overhead Gantry Hoarding Truss - 30m Span Ref

By Biswajit Date06-Dec-18 Chd Biswajit


Client Suntony Signage File Final Gantry Truss-30m Date/Time
Span.std 07-Dec-2018 20:06

Allowable Tensile Stress ft_allowable (MPa)


=0.60fy 144.00
Interaction ratio
=ft / ft_allowable 0.50
Status SAFE

Print Time/Date: 07/12/2018 20:09 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 561 of 617
Job No Sheet No Rev
BN/SS/-01 562
Part
Software licensed to BN
Job Title Design of Overhead Gantry Hoarding Truss - 30m Span Ref

By Biswajit Date06-Dec-18 Chd Biswajit


Client Suntony Signage File Final Gantry Truss-30m Date/Time
Span.std 07-Dec-2018 20:06

Design Of Member No. 272 As Per IS:800

Input Parameters

Member Section PIP889L

2
Cross Sectional Area Ax (mm ) 862.00
rz (mm) 30.31
ry (mm) 30.31
Unsupported Length - Major Axis For Slenderness Check Lz (mm) 1474.31
Unsupported Length - Minor Axis For Slenderness Check Ly (mm) 1474.31
Yield Stress fy (MPa) 240.00
Allowable Ratio For Interaction Check 1.00

Design Forces

Axial Load Fx (N ) 62066.82


Critical Loadcase No. 3

Details Of Calculation

Slenderness Checking

Lez (mm) 1474.31


Ley (mm) 1474.31
Lez / rz 48.64
Ley / ry 48.64
Actual Slenderness Ratio 48.64
Allowable Slenderness Ratio 180.00
Status SAFE

Check Against Axial Compression For Truss Member

Actual Compressive Stress fc (MPa)


=Fx / Ax 72.00

Calculation Of Allowable Compressive Stress :

Print Time/Date: 07/12/2018 20:09 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 562 of 617
Job No Sheet No Rev
BN/SS/-01 563
Part
Software licensed to BN
Job Title Design of Overhead Gantry Hoarding Truss - 30m Span Ref

By Biswajit Date06-Dec-18 Chd Biswajit


Client Suntony Signage File Final Gantry Truss-30m Date/Time
Span.std 07-Dec-2018 20:06

E (MPa) 200000.00
L/r 48.64
fcc (MPa)
2 2
=π E / λ 834.39
Allowable Compressive Stress fc_allowable (MPa)
1.4 1.4
=0.6fccfy / [(fcc) + (fy) ] 128.35
Interaction ratio
=fc / fc_allowable 0.56
Status SAFE

Print Time/Date: 07/12/2018 20:09 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 563 of 617
Job No Sheet No Rev
BN/SS/-01 564
Part
Software licensed to BN
Job Title Design of Overhead Gantry Hoarding Truss - 30m Span Ref

By Biswajit Date06-Dec-18 Chd Biswajit


Client Suntony Signage File Final Gantry Truss-30m Date/Time
Span.std 07-Dec-2018 20:06

Design Of Member No. 273 As Per IS:800

Input Parameters

Member Section PIP889L

2
Cross Sectional Area Ax (mm ) 862.00
Net section factor 1.00
2
Net Effective Sectional Area Anet (mm ) 862.00
rz (mm) 30.31
ry (mm) 30.31
Unsupported Length - Major Axis For Slenderness Check Lz (mm) 1474.32
Unsupported Length - Minor Axis For Slenderness Check Ly (mm) 1474.32
Yield Stress fy (MPa) 240.00
Allowable Ratio For Interaction Check 1.00

Design Forces

Axial Load Fx (N ) -62067.13


Critical Loadcase No. 3

Details Of Calculation

Slenderness Checking

Lez (mm) 1474.32


Ley (mm) 1474.32
Lez / rz 48.64
Ley / ry 48.64
Actual Slenderness Ratio 48.64
Allowable Slenderness Ratio 400.00
Status SAFE

Check Against Axial Tension For Truss Member

Actual Tensile Stress ft (MPa)


=Fx / Anet 72.00

Print Time/Date: 07/12/2018 20:09 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 564 of 617
Job No Sheet No Rev
BN/SS/-01 565
Part
Software licensed to BN
Job Title Design of Overhead Gantry Hoarding Truss - 30m Span Ref

By Biswajit Date06-Dec-18 Chd Biswajit


Client Suntony Signage File Final Gantry Truss-30m Date/Time
Span.std 07-Dec-2018 20:06

Allowable Tensile Stress ft_allowable (MPa)


=0.60fy 144.00
Interaction ratio
=ft / ft_allowable 0.50
Status SAFE

Print Time/Date: 07/12/2018 20:09 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 565 of 617
Job No Sheet No Rev
BN/SS/-01 566
Part
Software licensed to BN
Job Title Design of Overhead Gantry Hoarding Truss - 30m Span Ref

By Biswajit Date06-Dec-18 Chd Biswajit


Client Suntony Signage File Final Gantry Truss-30m Date/Time
Span.std 07-Dec-2018 20:06

Design Of Member No. 274 As Per IS:800

Input Parameters

Member Section PIP889L

2
Cross Sectional Area Ax (mm ) 862.00
Net section factor 1.00
2
Net Effective Sectional Area Anet (mm ) 862.00
rz (mm) 30.31
ry (mm) 30.31
Unsupported Length - Major Axis For Slenderness Check Lz (mm) 1474.31
Unsupported Length - Minor Axis For Slenderness Check Ly (mm) 1474.31
Yield Stress fy (MPa) 240.00
Allowable Ratio For Interaction Check 1.00

Design Forces

Axial Load Fx (N ) -47131.11


Critical Loadcase No. 3

Details Of Calculation

Slenderness Checking

Lez (mm) 1474.31


Ley (mm) 1474.31
Lez / rz 48.64
Ley / ry 48.64
Actual Slenderness Ratio 48.64
Allowable Slenderness Ratio 400.00
Status SAFE

Check Against Axial Tension For Truss Member

Actual Tensile Stress ft (MPa)


=Fx / Anet 54.68

Print Time/Date: 07/12/2018 20:09 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 566 of 617
Job No Sheet No Rev
BN/SS/-01 567
Part
Software licensed to BN
Job Title Design of Overhead Gantry Hoarding Truss - 30m Span Ref

By Biswajit Date06-Dec-18 Chd Biswajit


Client Suntony Signage File Final Gantry Truss-30m Date/Time
Span.std 07-Dec-2018 20:06

Allowable Tensile Stress ft_allowable (MPa)


=0.60fy 144.00
Interaction ratio
=ft / ft_allowable 0.38
Status SAFE

Print Time/Date: 07/12/2018 20:09 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 567 of 617
Job No Sheet No Rev
BN/SS/-01 568
Part
Software licensed to BN
Job Title Design of Overhead Gantry Hoarding Truss - 30m Span Ref

By Biswajit Date06-Dec-18 Chd Biswajit


Client Suntony Signage File Final Gantry Truss-30m Date/Time
Span.std 07-Dec-2018 20:06

Design Of Member No. 275 As Per IS:800

Input Parameters

Member Section PIP889L

2
Cross Sectional Area Ax (mm ) 862.00
rz (mm) 30.31
ry (mm) 30.31
Unsupported Length - Major Axis For Slenderness Check Lz (mm) 1474.32
Unsupported Length - Minor Axis For Slenderness Check Ly (mm) 1474.32
Yield Stress fy (MPa) 240.00
Allowable Ratio For Interaction Check 1.00

Design Forces

Axial Load Fx (N ) 47131.33


Critical Loadcase No. 3

Details Of Calculation

Slenderness Checking

Lez (mm) 1474.32


Ley (mm) 1474.32
Lez / rz 48.64
Ley / ry 48.64
Actual Slenderness Ratio 48.64
Allowable Slenderness Ratio 180.00
Status SAFE

Check Against Axial Compression For Truss Member

Actual Compressive Stress fc (MPa)


=Fx / Ax 54.68

Calculation Of Allowable Compressive Stress :

Print Time/Date: 07/12/2018 20:09 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 568 of 617
Job No Sheet No Rev
BN/SS/-01 569
Part
Software licensed to BN
Job Title Design of Overhead Gantry Hoarding Truss - 30m Span Ref

By Biswajit Date06-Dec-18 Chd Biswajit


Client Suntony Signage File Final Gantry Truss-30m Date/Time
Span.std 07-Dec-2018 20:06

E (MPa) 200000.00
L/r 48.64
fcc (MPa)
2 2
=π E / λ 834.38
Allowable Compressive Stress fc_allowable (MPa)
1.4 1.4
=0.6fccfy / [(fcc) + (fy) ] 128.35
Interaction ratio
=fc / fc_allowable 0.43
Status SAFE

Print Time/Date: 07/12/2018 20:09 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 569 of 617
Job No Sheet No Rev
BN/SS/-01 570
Part
Software licensed to BN
Job Title Design of Overhead Gantry Hoarding Truss - 30m Span Ref

By Biswajit Date06-Dec-18 Chd Biswajit


Client Suntony Signage File Final Gantry Truss-30m Date/Time
Span.std 07-Dec-2018 20:06

Design Of Member No. 276 As Per IS:800

Input Parameters

Member Section PIP889L

2
Cross Sectional Area Ax (mm ) 862.00
Net section factor 1.00
2
Net Effective Sectional Area Anet (mm ) 862.00
rz (mm) 30.31
ry (mm) 30.31
Unsupported Length - Major Axis For Slenderness Check Lz (mm) 1474.31
Unsupported Length - Minor Axis For Slenderness Check Ly (mm) 1474.31
Yield Stress fy (MPa) 240.00
Allowable Ratio For Interaction Check 1.00

Design Forces

Axial Load Fx (N ) -47131.11


Critical Loadcase No. 3

Details Of Calculation

Slenderness Checking

Lez (mm) 1474.31


Ley (mm) 1474.31
Lez / rz 48.64
Ley / ry 48.64
Actual Slenderness Ratio 48.64
Allowable Slenderness Ratio 400.00
Status SAFE

Check Against Axial Tension For Truss Member

Actual Tensile Stress ft (MPa)


=Fx / Anet 54.68

Print Time/Date: 07/12/2018 20:09 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 570 of 617
Job No Sheet No Rev
BN/SS/-01 571
Part
Software licensed to BN
Job Title Design of Overhead Gantry Hoarding Truss - 30m Span Ref

By Biswajit Date06-Dec-18 Chd Biswajit


Client Suntony Signage File Final Gantry Truss-30m Date/Time
Span.std 07-Dec-2018 20:06

Allowable Tensile Stress ft_allowable (MPa)


=0.60fy 144.00
Interaction ratio
=ft / ft_allowable 0.38
Status SAFE

Print Time/Date: 07/12/2018 20:09 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 571 of 617
Job No Sheet No Rev
BN/SS/-01 572
Part
Software licensed to BN
Job Title Design of Overhead Gantry Hoarding Truss - 30m Span Ref

By Biswajit Date06-Dec-18 Chd Biswajit


Client Suntony Signage File Final Gantry Truss-30m Date/Time
Span.std 07-Dec-2018 20:06

Design Of Member No. 277 As Per IS:800

Input Parameters

Member Section PIP889L

2
Cross Sectional Area Ax (mm ) 862.00
rz (mm) 30.31
ry (mm) 30.31
Unsupported Length - Major Axis For Slenderness Check Lz (mm) 1474.31
Unsupported Length - Minor Axis For Slenderness Check Ly (mm) 1474.31
Yield Stress fy (MPa) 240.00
Allowable Ratio For Interaction Check 1.00

Design Forces

Axial Load Fx (N ) 47131.11


Critical Loadcase No. 3

Details Of Calculation

Slenderness Checking

Lez (mm) 1474.31


Ley (mm) 1474.31
Lez / rz 48.64
Ley / ry 48.64
Actual Slenderness Ratio 48.64
Allowable Slenderness Ratio 180.00
Status SAFE

Check Against Axial Compression For Truss Member

Actual Compressive Stress fc (MPa)


=Fx / Ax 54.68

Calculation Of Allowable Compressive Stress :

Print Time/Date: 07/12/2018 20:09 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 572 of 617
Job No Sheet No Rev
BN/SS/-01 573
Part
Software licensed to BN
Job Title Design of Overhead Gantry Hoarding Truss - 30m Span Ref

By Biswajit Date06-Dec-18 Chd Biswajit


Client Suntony Signage File Final Gantry Truss-30m Date/Time
Span.std 07-Dec-2018 20:06

E (MPa) 200000.00
L/r 48.64
fcc (MPa)
2 2
=π E / λ 834.39
Allowable Compressive Stress fc_allowable (MPa)
1.4 1.4
=0.6fccfy / [(fcc) + (fy) ] 128.35
Interaction ratio
=fc / fc_allowable 0.43
Status SAFE

Print Time/Date: 07/12/2018 20:09 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 573 of 617
Job No Sheet No Rev
BN/SS/-01 574
Part
Software licensed to BN
Job Title Design of Overhead Gantry Hoarding Truss - 30m Span Ref

By Biswajit Date06-Dec-18 Chd Biswajit


Client Suntony Signage File Final Gantry Truss-30m Date/Time
Span.std 07-Dec-2018 20:06

Design Of Member No. 278 As Per IS:800

Input Parameters

Member Section PIP889L

2
Cross Sectional Area Ax (mm ) 862.00
Net section factor 1.00
2
Net Effective Sectional Area Anet (mm ) 862.00
rz (mm) 30.31
ry (mm) 30.31
Unsupported Length - Major Axis For Slenderness Check Lz (mm) 1474.32
Unsupported Length - Minor Axis For Slenderness Check Ly (mm) 1474.32
Yield Stress fy (MPa) 240.00
Allowable Ratio For Interaction Check 1.00

Design Forces

Axial Load Fx (N ) -47131.33


Critical Loadcase No. 3

Details Of Calculation

Slenderness Checking

Lez (mm) 1474.32


Ley (mm) 1474.32
Lez / rz 48.64
Ley / ry 48.64
Actual Slenderness Ratio 48.64
Allowable Slenderness Ratio 400.00
Status SAFE

Check Against Axial Tension For Truss Member

Actual Tensile Stress ft (MPa)


=Fx / Anet 54.68

Print Time/Date: 07/12/2018 20:09 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 574 of 617
Job No Sheet No Rev
BN/SS/-01 575
Part
Software licensed to BN
Job Title Design of Overhead Gantry Hoarding Truss - 30m Span Ref

By Biswajit Date06-Dec-18 Chd Biswajit


Client Suntony Signage File Final Gantry Truss-30m Date/Time
Span.std 07-Dec-2018 20:06

Allowable Tensile Stress ft_allowable (MPa)


=0.60fy 144.00
Interaction ratio
=ft / ft_allowable 0.38
Status SAFE

Print Time/Date: 07/12/2018 20:09 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 575 of 617
Job No Sheet No Rev
BN/SS/-01 576
Part
Software licensed to BN
Job Title Design of Overhead Gantry Hoarding Truss - 30m Span Ref

By Biswajit Date06-Dec-18 Chd Biswajit


Client Suntony Signage File Final Gantry Truss-30m Date/Time
Span.std 07-Dec-2018 20:06

Design Of Member No. 279 As Per IS:800

Input Parameters

Member Section PIP889L

2
Cross Sectional Area Ax (mm ) 862.00
Net section factor 1.00
2
Net Effective Sectional Area Anet (mm ) 862.00
rz (mm) 30.31
ry (mm) 30.31
Unsupported Length - Major Axis For Slenderness Check Lz (mm) 1474.31
Unsupported Length - Minor Axis For Slenderness Check Ly (mm) 1474.31
Yield Stress fy (MPa) 240.00
Allowable Ratio For Interaction Check 1.00

Design Forces

Axial Load Fx (N ) -385.10


Critical Loadcase No. 3

Details Of Calculation

Slenderness Checking

Lez (mm) 1474.31


Ley (mm) 1474.31
Lez / rz 48.64
Ley / ry 48.64
Actual Slenderness Ratio 48.64
Allowable Slenderness Ratio 400.00
Status SAFE

Check Against Axial Tension For Truss Member

Actual Tensile Stress ft (MPa)


=Fx / Anet 0.45

Print Time/Date: 07/12/2018 20:09 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 576 of 617
Job No Sheet No Rev
BN/SS/-01 577
Part
Software licensed to BN
Job Title Design of Overhead Gantry Hoarding Truss - 30m Span Ref

By Biswajit Date06-Dec-18 Chd Biswajit


Client Suntony Signage File Final Gantry Truss-30m Date/Time
Span.std 07-Dec-2018 20:06

Allowable Tensile Stress ft_allowable (MPa)


=0.60fy 144.00
Interaction ratio
=ft / ft_allowable 0.00
Status SAFE

Print Time/Date: 07/12/2018 20:09 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 577 of 617
Job No Sheet No Rev
BN/SS/-01 578
Part
Software licensed to BN
Job Title Design of Overhead Gantry Hoarding Truss - 30m Span Ref

By Biswajit Date06-Dec-18 Chd Biswajit


Client Suntony Signage File Final Gantry Truss-30m Date/Time
Span.std 07-Dec-2018 20:06

Design Of Member No. 280 As Per IS:800

Input Parameters

Member Section PIP889L

2
Cross Sectional Area Ax (mm ) 862.00
rz (mm) 30.31
ry (mm) 30.31
Unsupported Length - Major Axis For Slenderness Check Lz (mm) 1474.32
Unsupported Length - Minor Axis For Slenderness Check Ly (mm) 1474.32
Yield Stress fy (MPa) 240.00
Allowable Ratio For Interaction Check 1.00

Design Forces

Axial Load Fx (N ) 385.10


Critical Loadcase No. 3

Details Of Calculation

Slenderness Checking

Lez (mm) 1474.32


Ley (mm) 1474.32
Lez / rz 48.64
Ley / ry 48.64
Actual Slenderness Ratio 48.64
Allowable Slenderness Ratio 180.00
Status SAFE

Check Against Axial Compression For Truss Member

Actual Compressive Stress fc (MPa)


=Fx / Ax 0.45

Calculation Of Allowable Compressive Stress :

Print Time/Date: 07/12/2018 20:09 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 578 of 617
Job No Sheet No Rev
BN/SS/-01 579
Part
Software licensed to BN
Job Title Design of Overhead Gantry Hoarding Truss - 30m Span Ref

By Biswajit Date06-Dec-18 Chd Biswajit


Client Suntony Signage File Final Gantry Truss-30m Date/Time
Span.std 07-Dec-2018 20:06

E (MPa) 200000.00
L/r 48.64
fcc (MPa)
2 2
=π E / λ 834.38
Allowable Compressive Stress fc_allowable (MPa)
1.4 1.4
=0.6fccfy / [(fcc) + (fy) ] 128.35
Interaction ratio
=fc / fc_allowable 0.00
Status SAFE

Print Time/Date: 07/12/2018 20:09 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 579 of 617
Job No Sheet No Rev
BN/SS/-01 580
Part
Software licensed to BN
Job Title Design of Overhead Gantry Hoarding Truss - 30m Span Ref

By Biswajit Date06-Dec-18 Chd Biswajit


Client Suntony Signage File Final Gantry Truss-30m Date/Time
Span.std 07-Dec-2018 20:06

Design Of Member No. 281 As Per IS:800

Input Parameters

Member Section PIP889L

2
Cross Sectional Area Ax (mm ) 862.00
Net section factor 1.00
2
Net Effective Sectional Area Anet (mm ) 862.00
rz (mm) 30.31
ry (mm) 30.31
Unsupported Length - Major Axis For Slenderness Check Lz (mm) 1474.31
Unsupported Length - Minor Axis For Slenderness Check Ly (mm) 1474.31
Yield Stress fy (MPa) 240.00
Allowable Ratio For Interaction Check 1.00

Design Forces

Axial Load Fx (N ) -385.10


Critical Loadcase No. 3

Details Of Calculation

Slenderness Checking

Lez (mm) 1474.31


Ley (mm) 1474.31
Lez / rz 48.64
Ley / ry 48.64
Actual Slenderness Ratio 48.64
Allowable Slenderness Ratio 400.00
Status SAFE

Check Against Axial Tension For Truss Member

Actual Tensile Stress ft (MPa)


=Fx / Anet 0.45

Print Time/Date: 07/12/2018 20:09 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 580 of 617
Job No Sheet No Rev
BN/SS/-01 581
Part
Software licensed to BN
Job Title Design of Overhead Gantry Hoarding Truss - 30m Span Ref

By Biswajit Date06-Dec-18 Chd Biswajit


Client Suntony Signage File Final Gantry Truss-30m Date/Time
Span.std 07-Dec-2018 20:06

Allowable Tensile Stress ft_allowable (MPa)


=0.60fy 144.00
Interaction ratio
=ft / ft_allowable 0.00
Status SAFE

Print Time/Date: 07/12/2018 20:09 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 581 of 617
Job No Sheet No Rev
BN/SS/-01 582
Part
Software licensed to BN
Job Title Design of Overhead Gantry Hoarding Truss - 30m Span Ref

By Biswajit Date06-Dec-18 Chd Biswajit


Client Suntony Signage File Final Gantry Truss-30m Date/Time
Span.std 07-Dec-2018 20:06

Design Of Member No. 282 As Per IS:800

Input Parameters

Member Section PIP889L

2
Cross Sectional Area Ax (mm ) 862.00
rz (mm) 30.31
ry (mm) 30.31
Unsupported Length - Major Axis For Slenderness Check Lz (mm) 1474.31
Unsupported Length - Minor Axis For Slenderness Check Ly (mm) 1474.31
Yield Stress fy (MPa) 240.00
Allowable Ratio For Interaction Check 1.00

Design Forces

Axial Load Fx (N ) 385.10


Critical Loadcase No. 3

Details Of Calculation

Slenderness Checking

Lez (mm) 1474.31


Ley (mm) 1474.31
Lez / rz 48.64
Ley / ry 48.64
Actual Slenderness Ratio 48.64
Allowable Slenderness Ratio 180.00
Status SAFE

Check Against Axial Compression For Truss Member

Actual Compressive Stress fc (MPa)


=Fx / Ax 0.45

Calculation Of Allowable Compressive Stress :

Print Time/Date: 07/12/2018 20:09 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 582 of 617
Job No Sheet No Rev
BN/SS/-01 583
Part
Software licensed to BN
Job Title Design of Overhead Gantry Hoarding Truss - 30m Span Ref

By Biswajit Date06-Dec-18 Chd Biswajit


Client Suntony Signage File Final Gantry Truss-30m Date/Time
Span.std 07-Dec-2018 20:06

E (MPa) 200000.00
L/r 48.64
fcc (MPa)
2 2
=π E / λ 834.39
Allowable Compressive Stress fc_allowable (MPa)
1.4 1.4
=0.6fccfy / [(fcc) + (fy) ] 128.35
Interaction ratio
=fc / fc_allowable 0.00
Status SAFE

Print Time/Date: 07/12/2018 20:09 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 583 of 617
Job No Sheet No Rev
BN/SS/-01 584
Part
Software licensed to BN
Job Title Design of Overhead Gantry Hoarding Truss - 30m Span Ref

By Biswajit Date06-Dec-18 Chd Biswajit


Client Suntony Signage File Final Gantry Truss-30m Date/Time
Span.std 07-Dec-2018 20:06

Design Of Member No. 283 As Per IS:800

Input Parameters

Member Section PIP889L

2
Cross Sectional Area Ax (mm ) 862.00
Net section factor 1.00
2
Net Effective Sectional Area Anet (mm ) 862.00
rz (mm) 30.31
ry (mm) 30.31
Unsupported Length - Major Axis For Slenderness Check Lz (mm) 1474.32
Unsupported Length - Minor Axis For Slenderness Check Ly (mm) 1474.32
Yield Stress fy (MPa) 240.00
Allowable Ratio For Interaction Check 1.00

Design Forces

Axial Load Fx (N ) -385.10


Critical Loadcase No. 3

Details Of Calculation

Slenderness Checking

Lez (mm) 1474.32


Ley (mm) 1474.32
Lez / rz 48.64
Ley / ry 48.64
Actual Slenderness Ratio 48.64
Allowable Slenderness Ratio 400.00
Status SAFE

Check Against Axial Tension For Truss Member

Actual Tensile Stress ft (MPa)


=Fx / Anet 0.45

Print Time/Date: 07/12/2018 20:09 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 584 of 617
Job No Sheet No Rev
BN/SS/-01 585
Part
Software licensed to BN
Job Title Design of Overhead Gantry Hoarding Truss - 30m Span Ref

By Biswajit Date06-Dec-18 Chd Biswajit


Client Suntony Signage File Final Gantry Truss-30m Date/Time
Span.std 07-Dec-2018 20:06

Allowable Tensile Stress ft_allowable (MPa)


=0.60fy 144.00
Interaction ratio
=ft / ft_allowable 0.00
Status SAFE

Print Time/Date: 07/12/2018 20:09 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 585 of 617
Job No Sheet No Rev
BN/SS/-01 586
Part
Software licensed to BN
Job Title Design of Overhead Gantry Hoarding Truss - 30m Span Ref

By Biswajit Date06-Dec-18 Chd Biswajit


Client Suntony Signage File Final Gantry Truss-30m Date/Time
Span.std 07-Dec-2018 20:06

Design Of Member No. 284 As Per IS:800

Input Parameters

Member Section PIP889L

2
Cross Sectional Area Ax (mm ) 862.00
rz (mm) 30.31
ry (mm) 30.31
Unsupported Length - Major Axis For Slenderness Check Lz (mm) 1850.29
Unsupported Length - Minor Axis For Slenderness Check Ly (mm) 1850.29
Yield Stress fy (MPa) 240.00
Allowable Ratio For Interaction Check 1.00

Design Forces

Axial Load Fx (N ) 14940.35


Critical Loadcase No. 3

Details Of Calculation

Slenderness Checking

Lez (mm) 1850.29


Ley (mm) 1850.29
Lez / rz 61.04
Ley / ry 61.04
Actual Slenderness Ratio 61.04
Allowable Slenderness Ratio 180.00
Status SAFE

Check Against Axial Compression For Truss Member

Actual Compressive Stress fc (MPa)


=Fx / Ax 17.33

Calculation Of Allowable Compressive Stress :

Print Time/Date: 07/12/2018 20:09 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 586 of 617
Job No Sheet No Rev
BN/SS/-01 587
Part
Software licensed to BN
Job Title Design of Overhead Gantry Hoarding Truss - 30m Span Ref

By Biswajit Date06-Dec-18 Chd Biswajit


Client Suntony Signage File Final Gantry Truss-30m Date/Time
Span.std 07-Dec-2018 20:06

E (MPa) 200000.00
L/r 61.04
fcc (MPa)
2 2
=π E / λ 529.74
Allowable Compressive Stress fc_allowable (MPa)
1.4 1.4
=0.6fccfy / [(fcc) + (fy) ] 117.45
Interaction ratio
=fc / fc_allowable 0.15
Status SAFE

Print Time/Date: 07/12/2018 20:09 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 587 of 617
Job No Sheet No Rev
BN/SS/-01 588
Part
Software licensed to BN
Job Title Design of Overhead Gantry Hoarding Truss - 30m Span Ref

By Biswajit Date06-Dec-18 Chd Biswajit


Client Suntony Signage File Final Gantry Truss-30m Date/Time
Span.std 07-Dec-2018 20:06

Design Of Member No. 285 As Per IS:800

Input Parameters

Member Section PIP889L

2
Cross Sectional Area Ax (mm ) 862.00
Net section factor 1.00
2
Net Effective Sectional Area Anet (mm ) 862.00
rz (mm) 30.31
ry (mm) 30.31
Unsupported Length - Major Axis For Slenderness Check Lz (mm) 1850.29
Unsupported Length - Minor Axis For Slenderness Check Ly (mm) 1850.29
Yield Stress fy (MPa) 240.00
Allowable Ratio For Interaction Check 1.00

Design Forces

Axial Load Fx (N ) -26342.24


Critical Loadcase No. 3

Details Of Calculation

Slenderness Checking

Lez (mm) 1850.29


Ley (mm) 1850.29
Lez / rz 61.04
Ley / ry 61.04
Actual Slenderness Ratio 61.04
Allowable Slenderness Ratio 400.00
Status SAFE

Check Against Axial Tension For Truss Member

Actual Tensile Stress ft (MPa)


=Fx / Anet 30.56

Print Time/Date: 07/12/2018 20:09 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 588 of 617
Job No Sheet No Rev
BN/SS/-01 589
Part
Software licensed to BN
Job Title Design of Overhead Gantry Hoarding Truss - 30m Span Ref

By Biswajit Date06-Dec-18 Chd Biswajit


Client Suntony Signage File Final Gantry Truss-30m Date/Time
Span.std 07-Dec-2018 20:06

Allowable Tensile Stress ft_allowable (MPa)


=0.60fy 144.00
Interaction ratio
=ft / ft_allowable 0.21
Status SAFE

Print Time/Date: 07/12/2018 20:09 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 589 of 617
Job No Sheet No Rev
BN/SS/-01 590
Part
Software licensed to BN
Job Title Design of Overhead Gantry Hoarding Truss - 30m Span Ref

By Biswajit Date06-Dec-18 Chd Biswajit


Client Suntony Signage File Final Gantry Truss-30m Date/Time
Span.std 07-Dec-2018 20:06

Design Of Member No. 286 As Per IS:800

Input Parameters

Member Section PIP889L

2
Cross Sectional Area Ax (mm ) 862.00
Net section factor 1.00
2
Net Effective Sectional Area Anet (mm ) 862.00
rz (mm) 30.31
ry (mm) 30.31
Unsupported Length - Major Axis For Slenderness Check Lz (mm) 1850.29
Unsupported Length - Minor Axis For Slenderness Check Ly (mm) 1850.29
Yield Stress fy (MPa) 240.00
Allowable Ratio For Interaction Check 1.00

Design Forces

Axial Load Fx (N ) -10308.90


Critical Loadcase No. 3

Details Of Calculation

Slenderness Checking

Lez (mm) 1850.29


Ley (mm) 1850.29
Lez / rz 61.04
Ley / ry 61.04
Actual Slenderness Ratio 61.04
Allowable Slenderness Ratio 400.00
Status SAFE

Check Against Axial Tension For Truss Member

Actual Tensile Stress ft (MPa)


=Fx / Anet 11.96

Print Time/Date: 07/12/2018 20:09 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 590 of 617
Job No Sheet No Rev
BN/SS/-01 591
Part
Software licensed to BN
Job Title Design of Overhead Gantry Hoarding Truss - 30m Span Ref

By Biswajit Date06-Dec-18 Chd Biswajit


Client Suntony Signage File Final Gantry Truss-30m Date/Time
Span.std 07-Dec-2018 20:06

Allowable Tensile Stress ft_allowable (MPa)


=0.60fy 144.00
Interaction ratio
=ft / ft_allowable 0.08
Status SAFE

Print Time/Date: 07/12/2018 20:09 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 591 of 617
Job No Sheet No Rev
BN/SS/-01 592
Part
Software licensed to BN
Job Title Design of Overhead Gantry Hoarding Truss - 30m Span Ref

By Biswajit Date06-Dec-18 Chd Biswajit


Client Suntony Signage File Final Gantry Truss-30m Date/Time
Span.std 07-Dec-2018 20:06

Design Of Member No. 287 As Per IS:800

Input Parameters

Member Section PIP889L

2
Cross Sectional Area Ax (mm ) 862.00
rz (mm) 30.31
ry (mm) 30.31
Unsupported Length - Major Axis For Slenderness Check Lz (mm) 1850.29
Unsupported Length - Minor Axis For Slenderness Check Ly (mm) 1850.29
Yield Stress fy (MPa) 240.00
Allowable Ratio For Interaction Check 1.00

Design Forces

Axial Load Fx (N ) 30973.69


Critical Loadcase No. 3

Details Of Calculation

Slenderness Checking

Lez (mm) 1850.29


Ley (mm) 1850.29
Lez / rz 61.04
Ley / ry 61.04
Actual Slenderness Ratio 61.04
Allowable Slenderness Ratio 180.00
Status SAFE

Check Against Axial Compression For Truss Member

Actual Compressive Stress fc (MPa)


=Fx / Ax 35.93

Calculation Of Allowable Compressive Stress :

Print Time/Date: 07/12/2018 20:09 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 592 of 617
Job No Sheet No Rev
BN/SS/-01 593
Part
Software licensed to BN
Job Title Design of Overhead Gantry Hoarding Truss - 30m Span Ref

By Biswajit Date06-Dec-18 Chd Biswajit


Client Suntony Signage File Final Gantry Truss-30m Date/Time
Span.std 07-Dec-2018 20:06

E (MPa) 200000.00
L/r 61.04
fcc (MPa)
2 2
=π E / λ 529.74
Allowable Compressive Stress fc_allowable (MPa)
1.4 1.4
=0.6fccfy / [(fcc) + (fy) ] 117.45
Interaction ratio
=fc / fc_allowable 0.31
Status SAFE

Print Time/Date: 07/12/2018 20:09 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 593 of 617
Job No Sheet No Rev
BN/SS/-01 594
Part
Software licensed to BN
Job Title Design of Overhead Gantry Hoarding Truss - 30m Span Ref

By Biswajit Date06-Dec-18 Chd Biswajit


Client Suntony Signage File Final Gantry Truss-30m Date/Time
Span.std 07-Dec-2018 20:06

Design Of Member No. 288 As Per IS:800

Input Parameters

Member Section PIP889L

2
Cross Sectional Area Ax (mm ) 862.00
rz (mm) 30.31
ry (mm) 30.31
Unsupported Length - Major Axis For Slenderness Check Lz (mm) 1850.29
Unsupported Length - Minor Axis For Slenderness Check Ly (mm) 1850.29
Yield Stress fy (MPa) 240.00
Allowable Ratio For Interaction Check 1.00

Design Forces

Axial Load Fx (N ) 37.66


Critical Loadcase No. 3

Details Of Calculation

Slenderness Checking

Lez (mm) 1850.29


Ley (mm) 1850.29
Lez / rz 61.04
Ley / ry 61.04
Actual Slenderness Ratio 61.04
Allowable Slenderness Ratio 400.00
Status SAFE

Check Against Axial Compression For Truss Member

Actual Compressive Stress fc (MPa)


=Fx / Ax 0.04

Calculation Of Allowable Compressive Stress :

Print Time/Date: 07/12/2018 20:09 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 594 of 617
Job No Sheet No Rev
BN/SS/-01 595
Part
Software licensed to BN
Job Title Design of Overhead Gantry Hoarding Truss - 30m Span Ref

By Biswajit Date06-Dec-18 Chd Biswajit


Client Suntony Signage File Final Gantry Truss-30m Date/Time
Span.std 07-Dec-2018 20:06

E (MPa) 200000.00
L/r 61.04
fcc (MPa)
2 2
=π E / λ 529.74
Allowable Compressive Stress fc_allowable (MPa)
1.4 1.4
=0.6fccfy / [(fcc) + (fy) ] 117.45
Interaction ratio
=fc / fc_allowable 0.00
Status SAFE

Print Time/Date: 07/12/2018 20:09 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 595 of 617
Job No Sheet No Rev
BN/SS/-01 596
Part
Software licensed to BN
Job Title Design of Overhead Gantry Hoarding Truss - 30m Span Ref

By Biswajit Date06-Dec-18 Chd Biswajit


Client Suntony Signage File Final Gantry Truss-30m Date/Time
Span.std 07-Dec-2018 20:06

Design Of Member No. 289 As Per IS:800

Input Parameters

Member Section PIP889L

2
Cross Sectional Area Ax (mm ) 862.00
rz (mm) 30.31
ry (mm) 30.31
Unsupported Length - Major Axis For Slenderness Check Lz (mm) 1850.29
Unsupported Length - Minor Axis For Slenderness Check Ly (mm) 1850.29
Yield Stress fy (MPa) 240.00
Allowable Ratio For Interaction Check 1.00

Design Forces

Axial Load Fx (N ) 37.66


Critical Loadcase No. 3

Details Of Calculation

Slenderness Checking

Lez (mm) 1850.29


Ley (mm) 1850.29
Lez / rz 61.04
Ley / ry 61.04
Actual Slenderness Ratio 61.04
Allowable Slenderness Ratio 400.00
Status SAFE

Check Against Axial Compression For Truss Member

Actual Compressive Stress fc (MPa)


=Fx / Ax 0.04

Calculation Of Allowable Compressive Stress :

Print Time/Date: 07/12/2018 20:09 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 596 of 617
Job No Sheet No Rev
BN/SS/-01 597
Part
Software licensed to BN
Job Title Design of Overhead Gantry Hoarding Truss - 30m Span Ref

By Biswajit Date06-Dec-18 Chd Biswajit


Client Suntony Signage File Final Gantry Truss-30m Date/Time
Span.std 07-Dec-2018 20:06

E (MPa) 200000.00
L/r 61.04
fcc (MPa)
2 2
=π E / λ 529.74
Allowable Compressive Stress fc_allowable (MPa)
1.4 1.4
=0.6fccfy / [(fcc) + (fy) ] 117.45
Interaction ratio
=fc / fc_allowable 0.00
Status SAFE

Print Time/Date: 07/12/2018 20:09 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 597 of 617
Job No Sheet No Rev
BN/SS/-01 598
Part
Software licensed to BN
Job Title Design of Overhead Gantry Hoarding Truss - 30m Span Ref

By Biswajit Date06-Dec-18 Chd Biswajit


Client Suntony Signage File Final Gantry Truss-30m Date/Time
Span.std 07-Dec-2018 20:06

Design Of Member No. 290 As Per IS:800

Input Parameters

Member Section PIP889L

2
Cross Sectional Area Ax (mm ) 862.00
rz (mm) 30.31
ry (mm) 30.31
Unsupported Length - Major Axis For Slenderness Check Lz (mm) 1850.29
Unsupported Length - Minor Axis For Slenderness Check Ly (mm) 1850.29
Yield Stress fy (MPa) 240.00
Allowable Ratio For Interaction Check 1.00

Design Forces

Axial Load Fx (N ) 37.66


Critical Loadcase No. 3

Details Of Calculation

Slenderness Checking

Lez (mm) 1850.29


Ley (mm) 1850.29
Lez / rz 61.04
Ley / ry 61.04
Actual Slenderness Ratio 61.04
Allowable Slenderness Ratio 400.00
Status SAFE

Check Against Axial Compression For Truss Member

Actual Compressive Stress fc (MPa)


=Fx / Ax 0.04

Calculation Of Allowable Compressive Stress :

Print Time/Date: 07/12/2018 20:09 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 598 of 617
Job No Sheet No Rev
BN/SS/-01 599
Part
Software licensed to BN
Job Title Design of Overhead Gantry Hoarding Truss - 30m Span Ref

By Biswajit Date06-Dec-18 Chd Biswajit


Client Suntony Signage File Final Gantry Truss-30m Date/Time
Span.std 07-Dec-2018 20:06

E (MPa) 200000.00
L/r 61.04
fcc (MPa)
2 2
=π E / λ 529.74
Allowable Compressive Stress fc_allowable (MPa)
1.4 1.4
=0.6fccfy / [(fcc) + (fy) ] 117.45
Interaction ratio
=fc / fc_allowable 0.00
Status SAFE

Print Time/Date: 07/12/2018 20:09 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 599 of 617
Job No Sheet No Rev
BN/SS/-01 600
Part
Software licensed to BN
Job Title Design of Overhead Gantry Hoarding Truss - 30m Span Ref

By Biswajit Date06-Dec-18 Chd Biswajit


Client Suntony Signage File Final Gantry Truss-30m Date/Time
Span.std 07-Dec-2018 20:06

Design Of Member No. 291 As Per IS:800

Input Parameters

Member Section PIP889L

2
Cross Sectional Area Ax (mm ) 862.00
rz (mm) 30.31
ry (mm) 30.31
Unsupported Length - Major Axis For Slenderness Check Lz (mm) 1850.29
Unsupported Length - Minor Axis For Slenderness Check Ly (mm) 1850.29
Yield Stress fy (MPa) 240.00
Allowable Ratio For Interaction Check 1.00

Design Forces

Axial Load Fx (N ) 37.66


Critical Loadcase No. 3

Details Of Calculation

Slenderness Checking

Lez (mm) 1850.29


Ley (mm) 1850.29
Lez / rz 61.04
Ley / ry 61.04
Actual Slenderness Ratio 61.04
Allowable Slenderness Ratio 400.00
Status SAFE

Check Against Axial Compression For Truss Member

Actual Compressive Stress fc (MPa)


=Fx / Ax 0.04

Calculation Of Allowable Compressive Stress :

Print Time/Date: 07/12/2018 20:09 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 600 of 617
Job No Sheet No Rev
BN/SS/-01 601
Part
Software licensed to BN
Job Title Design of Overhead Gantry Hoarding Truss - 30m Span Ref

By Biswajit Date06-Dec-18 Chd Biswajit


Client Suntony Signage File Final Gantry Truss-30m Date/Time
Span.std 07-Dec-2018 20:06

E (MPa) 200000.00
L/r 61.04
fcc (MPa)
2 2
=π E / λ 529.74
Allowable Compressive Stress fc_allowable (MPa)
1.4 1.4
=0.6fccfy / [(fcc) + (fy) ] 117.45
Interaction ratio
=fc / fc_allowable 0.00
Status SAFE

Print Time/Date: 07/12/2018 20:09 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 601 of 617
Job No Sheet No Rev
BN/SS/-01 602
Part
Software licensed to BN
Job Title Design of Overhead Gantry Hoarding Truss - 30m Span Ref

By Biswajit Date06-Dec-18 Chd Biswajit


Client Suntony Signage File Final Gantry Truss-30m Date/Time
Span.std 07-Dec-2018 20:06

Design Of Member No. 292 As Per IS:800

Input Parameters

Member Section PIP889L

2
Cross Sectional Area Ax (mm ) 862.00
rz (mm) 30.31
ry (mm) 30.31
Unsupported Length - Major Axis For Slenderness Check Lz (mm) 1474.31
Unsupported Length - Minor Axis For Slenderness Check Ly (mm) 1474.31
Yield Stress fy (MPa) 240.00
Allowable Ratio For Interaction Check 1.00

Design Forces

Axial Load Fx (N ) 5240.17


Critical Loadcase No. 3

Details Of Calculation

Slenderness Checking

Lez (mm) 1474.31


Ley (mm) 1474.31
Lez / rz 48.64
Ley / ry 48.64
Actual Slenderness Ratio 48.64
Allowable Slenderness Ratio 180.00
Status SAFE

Check Against Axial Compression For Truss Member

Actual Compressive Stress fc (MPa)


=Fx / Ax 6.08

Calculation Of Allowable Compressive Stress :

Print Time/Date: 07/12/2018 20:09 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 602 of 617
Job No Sheet No Rev
BN/SS/-01 603
Part
Software licensed to BN
Job Title Design of Overhead Gantry Hoarding Truss - 30m Span Ref

By Biswajit Date06-Dec-18 Chd Biswajit


Client Suntony Signage File Final Gantry Truss-30m Date/Time
Span.std 07-Dec-2018 20:06

E (MPa) 200000.00
L/r 48.64
fcc (MPa)
2 2
=π E / λ 834.39
Allowable Compressive Stress fc_allowable (MPa)
1.4 1.4
=0.6fccfy / [(fcc) + (fy) ] 128.35
Interaction ratio
=fc / fc_allowable 0.05
Status SAFE

Print Time/Date: 07/12/2018 20:09 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 603 of 617
Job No Sheet No Rev
BN/SS/-01 604
Part
Software licensed to BN
Job Title Design of Overhead Gantry Hoarding Truss - 30m Span Ref

By Biswajit Date06-Dec-18 Chd Biswajit


Client Suntony Signage File Final Gantry Truss-30m Date/Time
Span.std 07-Dec-2018 20:06

Design Of Member No. 293 As Per IS:800

Input Parameters

Member Section PIP889L

2
Cross Sectional Area Ax (mm ) 862.00
Net section factor 1.00
2
Net Effective Sectional Area Anet (mm ) 862.00
rz (mm) 30.31
ry (mm) 30.31
Unsupported Length - Major Axis For Slenderness Check Lz (mm) 1474.31
Unsupported Length - Minor Axis For Slenderness Check Ly (mm) 1474.31
Yield Stress fy (MPa) 240.00
Allowable Ratio For Interaction Check 1.00

Design Forces

Axial Load Fx (N ) -5341.35


Critical Loadcase No. 3

Details Of Calculation

Slenderness Checking

Lez (mm) 1474.31


Ley (mm) 1474.31
Lez / rz 48.64
Ley / ry 48.64
Actual Slenderness Ratio 48.64
Allowable Slenderness Ratio 400.00
Status SAFE

Check Against Axial Tension For Truss Member

Actual Tensile Stress ft (MPa)


=Fx / Anet 6.20

Print Time/Date: 07/12/2018 20:09 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 604 of 617
Job No Sheet No Rev
BN/SS/-01 605
Part
Software licensed to BN
Job Title Design of Overhead Gantry Hoarding Truss - 30m Span Ref

By Biswajit Date06-Dec-18 Chd Biswajit


Client Suntony Signage File Final Gantry Truss-30m Date/Time
Span.std 07-Dec-2018 20:06

Allowable Tensile Stress ft_allowable (MPa)


=0.60fy 144.00
Interaction ratio
=ft / ft_allowable 0.04
Status SAFE

Print Time/Date: 07/12/2018 20:09 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 605 of 617
Job No Sheet No Rev
BN/SS/-01 606
Part
Software licensed to BN
Job Title Design of Overhead Gantry Hoarding Truss - 30m Span Ref

By Biswajit Date06-Dec-18 Chd Biswajit


Client Suntony Signage File Final Gantry Truss-30m Date/Time
Span.std 07-Dec-2018 20:06

Design Of Member No. 294 As Per IS:800

Input Parameters

Member Section PIP889L

2
Cross Sectional Area Ax (mm ) 862.00
Net section factor 1.00
2
Net Effective Sectional Area Anet (mm ) 862.00
rz (mm) 30.31
ry (mm) 30.31
Unsupported Length - Major Axis For Slenderness Check Lz (mm) 1474.31
Unsupported Length - Minor Axis For Slenderness Check Ly (mm) 1474.31
Yield Stress fy (MPa) 240.00
Allowable Ratio For Interaction Check 1.00

Design Forces

Axial Load Fx (N ) -27901.93


Critical Loadcase No. 3

Details Of Calculation

Slenderness Checking

Lez (mm) 1474.31


Ley (mm) 1474.31
Lez / rz 48.64
Ley / ry 48.64
Actual Slenderness Ratio 48.64
Allowable Slenderness Ratio 400.00
Status SAFE

Check Against Axial Tension For Truss Member

Actual Tensile Stress ft (MPa)


=Fx / Anet 32.37

Print Time/Date: 07/12/2018 20:09 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 606 of 617
Job No Sheet No Rev
BN/SS/-01 607
Part
Software licensed to BN
Job Title Design of Overhead Gantry Hoarding Truss - 30m Span Ref

By Biswajit Date06-Dec-18 Chd Biswajit


Client Suntony Signage File Final Gantry Truss-30m Date/Time
Span.std 07-Dec-2018 20:06

Allowable Tensile Stress ft_allowable (MPa)


=0.60fy 144.00
Interaction ratio
=ft / ft_allowable 0.22
Status SAFE

Print Time/Date: 07/12/2018 20:09 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 607 of 617
Job No Sheet No Rev
BN/SS/-01 608
Part
Software licensed to BN
Job Title Design of Overhead Gantry Hoarding Truss - 30m Span Ref

By Biswajit Date06-Dec-18 Chd Biswajit


Client Suntony Signage File Final Gantry Truss-30m Date/Time
Span.std 07-Dec-2018 20:06

Design Of Member No. 295 As Per IS:800

Input Parameters

Member Section PIP889L

2
Cross Sectional Area Ax (mm ) 862.00
rz (mm) 30.31
ry (mm) 30.31
Unsupported Length - Major Axis For Slenderness Check Lz (mm) 1474.31
Unsupported Length - Minor Axis For Slenderness Check Ly (mm) 1474.31
Yield Stress fy (MPa) 240.00
Allowable Ratio For Interaction Check 1.00

Design Forces

Axial Load Fx (N ) 34202.55


Critical Loadcase No. 3

Details Of Calculation

Slenderness Checking

Lez (mm) 1474.31


Ley (mm) 1474.31
Lez / rz 48.64
Ley / ry 48.64
Actual Slenderness Ratio 48.64
Allowable Slenderness Ratio 180.00
Status SAFE

Check Against Axial Compression For Truss Member

Actual Compressive Stress fc (MPa)


=Fx / Ax 39.68

Calculation Of Allowable Compressive Stress :

Print Time/Date: 07/12/2018 20:09 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 608 of 617
Job No Sheet No Rev
BN/SS/-01 609
Part
Software licensed to BN
Job Title Design of Overhead Gantry Hoarding Truss - 30m Span Ref

By Biswajit Date06-Dec-18 Chd Biswajit


Client Suntony Signage File Final Gantry Truss-30m Date/Time
Span.std 07-Dec-2018 20:06

E (MPa) 200000.00
L/r 48.64
fcc (MPa)
2 2
=π E / λ 834.39
Allowable Compressive Stress fc_allowable (MPa)
1.4 1.4
=0.6fccfy / [(fcc) + (fy) ] 128.35
Interaction ratio
=fc / fc_allowable 0.31
Status SAFE

Print Time/Date: 07/12/2018 20:09 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 609 of 617
Job No Sheet No Rev
BN/SS/-01 610
Part
Software licensed to BN
Job Title Design of Overhead Gantry Hoarding Truss - 30m Span Ref

By Biswajit Date06-Dec-18 Chd Biswajit


Client Suntony Signage File Final Gantry Truss-30m Date/Time
Span.std 07-Dec-2018 20:06

Design Of Member No. 296 As Per IS:800

Input Parameters

Member Section PIP889L

2
Cross Sectional Area Ax (mm ) 862.00
rz (mm) 30.31
ry (mm) 30.31
Unsupported Length - Major Axis For Slenderness Check Lz (mm) 1474.31
Unsupported Length - Minor Axis For Slenderness Check Ly (mm) 1474.31
Yield Stress fy (MPa) 240.00
Allowable Ratio For Interaction Check 1.00

Design Forces

Axial Load Fx (N ) 26533.70


Critical Loadcase No. 3

Details Of Calculation

Slenderness Checking

Lez (mm) 1474.31


Ley (mm) 1474.31
Lez / rz 48.64
Ley / ry 48.64
Actual Slenderness Ratio 48.64
Allowable Slenderness Ratio 180.00
Status SAFE

Check Against Axial Compression For Truss Member

Actual Compressive Stress fc (MPa)


=Fx / Ax 30.78

Calculation Of Allowable Compressive Stress :

Print Time/Date: 07/12/2018 20:09 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 610 of 617
Job No Sheet No Rev
BN/SS/-01 611
Part
Software licensed to BN
Job Title Design of Overhead Gantry Hoarding Truss - 30m Span Ref

By Biswajit Date06-Dec-18 Chd Biswajit


Client Suntony Signage File Final Gantry Truss-30m Date/Time
Span.std 07-Dec-2018 20:06

E (MPa) 200000.00
L/r 48.64
fcc (MPa)
2 2
=π E / λ 834.39
Allowable Compressive Stress fc_allowable (MPa)
1.4 1.4
=0.6fccfy / [(fcc) + (fy) ] 128.35
Interaction ratio
=fc / fc_allowable 0.24
Status SAFE

Print Time/Date: 07/12/2018 20:09 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 611 of 617
Job No Sheet No Rev
BN/SS/-01 612
Part
Software licensed to BN
Job Title Design of Overhead Gantry Hoarding Truss - 30m Span Ref

By Biswajit Date06-Dec-18 Chd Biswajit


Client Suntony Signage File Final Gantry Truss-30m Date/Time
Span.std 07-Dec-2018 20:06

Design Of Member No. 297 As Per IS:800

Input Parameters

Member Section PIP889L

2
Cross Sectional Area Ax (mm ) 862.00
Net section factor 1.00
2
Net Effective Sectional Area Anet (mm ) 862.00
rz (mm) 30.31
ry (mm) 30.31
Unsupported Length - Major Axis For Slenderness Check Lz (mm) 1474.31
Unsupported Length - Minor Axis For Slenderness Check Ly (mm) 1474.31
Yield Stress fy (MPa) 240.00
Allowable Ratio For Interaction Check 1.00

Design Forces

Axial Load Fx (N ) -20635.07


Critical Loadcase No. 3

Details Of Calculation

Slenderness Checking

Lez (mm) 1474.31


Ley (mm) 1474.31
Lez / rz 48.64
Ley / ry 48.64
Actual Slenderness Ratio 48.64
Allowable Slenderness Ratio 400.00
Status SAFE

Check Against Axial Tension For Truss Member

Actual Tensile Stress ft (MPa)


=Fx / Anet 23.94

Print Time/Date: 07/12/2018 20:09 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 612 of 617
Job No Sheet No Rev
BN/SS/-01 613
Part
Software licensed to BN
Job Title Design of Overhead Gantry Hoarding Truss - 30m Span Ref

By Biswajit Date06-Dec-18 Chd Biswajit


Client Suntony Signage File Final Gantry Truss-30m Date/Time
Span.std 07-Dec-2018 20:06

Allowable Tensile Stress ft_allowable (MPa)


=0.60fy 144.00
Interaction ratio
=ft / ft_allowable 0.17
Status SAFE

Print Time/Date: 07/12/2018 20:09 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 613 of 617
Job No Sheet No Rev
BN/SS/-01 614
Part
Software licensed to BN
Job Title Design of Overhead Gantry Hoarding Truss - 30m Span Ref

By Biswajit Date06-Dec-18 Chd Biswajit


Client Suntony Signage File Final Gantry Truss-30m Date/Time
Span.std 07-Dec-2018 20:06

Design Of Member No. 298 As Per IS:800

Input Parameters

Member Section PIP889L

2
Cross Sectional Area Ax (mm ) 862.00
Net section factor 1.00
2
Net Effective Sectional Area Anet (mm ) 862.00
rz (mm) 30.31
ry (mm) 30.31
Unsupported Length - Major Axis For Slenderness Check Lz (mm) 1474.31
Unsupported Length - Minor Axis For Slenderness Check Ly (mm) 1474.31
Yield Stress fy (MPa) 240.00
Allowable Ratio For Interaction Check 1.00

Design Forces

Axial Load Fx (N ) -129.70


Critical Loadcase No. 3

Details Of Calculation

Slenderness Checking

Lez (mm) 1474.31


Ley (mm) 1474.31
Lez / rz 48.64
Ley / ry 48.64
Actual Slenderness Ratio 48.64
Allowable Slenderness Ratio 400.00
Status SAFE

Check Against Axial Tension For Truss Member

Actual Tensile Stress ft (MPa)


=Fx / Anet 0.15

Print Time/Date: 07/12/2018 20:09 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 614 of 617
Job No Sheet No Rev
BN/SS/-01 615
Part
Software licensed to BN
Job Title Design of Overhead Gantry Hoarding Truss - 30m Span Ref

By Biswajit Date06-Dec-18 Chd Biswajit


Client Suntony Signage File Final Gantry Truss-30m Date/Time
Span.std 07-Dec-2018 20:06

Allowable Tensile Stress ft_allowable (MPa)


=0.60fy 144.00
Interaction ratio
=ft / ft_allowable 0.00
Status SAFE

Print Time/Date: 07/12/2018 20:09 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 615 of 617
Job No Sheet No Rev
BN/SS/-01 616
Part
Software licensed to BN
Job Title Design of Overhead Gantry Hoarding Truss - 30m Span Ref

By Biswajit Date06-Dec-18 Chd Biswajit


Client Suntony Signage File Final Gantry Truss-30m Date/Time
Span.std 07-Dec-2018 20:06

Design Of Member No. 299 As Per IS:800

Input Parameters

Member Section PIP889L

2
Cross Sectional Area Ax (mm ) 862.00
Net section factor 1.00
2
Net Effective Sectional Area Anet (mm ) 862.00
rz (mm) 30.31
ry (mm) 30.31
Unsupported Length - Major Axis For Slenderness Check Lz (mm) 1474.31
Unsupported Length - Minor Axis For Slenderness Check Ly (mm) 1474.31
Yield Stress fy (MPa) 240.00
Allowable Ratio For Interaction Check 1.00

Design Forces

Axial Load Fx (N ) -477.13


Critical Loadcase No. 3

Details Of Calculation

Slenderness Checking

Lez (mm) 1474.31


Ley (mm) 1474.31
Lez / rz 48.64
Ley / ry 48.64
Actual Slenderness Ratio 48.64
Allowable Slenderness Ratio 400.00
Status SAFE

Check Against Axial Tension For Truss Member

Actual Tensile Stress ft (MPa)


=Fx / Anet 0.55

Print Time/Date: 07/12/2018 20:09 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 616 of 617
Job No Sheet No Rev
BN/SS/-01 617
Part
Software licensed to BN
Job Title Design of Overhead Gantry Hoarding Truss - 30m Span Ref

By Biswajit Date06-Dec-18 Chd Biswajit


Client Suntony Signage File Final Gantry Truss-30m Date/Time
Span.std 07-Dec-2018 20:06

Allowable Tensile Stress ft_allowable (MPa)


=0.60fy 144.00
Interaction ratio
=ft / ft_allowable 0.00
Status SAFE

Print Time/Date: 07/12/2018 20:09 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 617 of 617

You might also like