Professional Documents
Culture Documents
Lifting
Rigging
4WD Recovery
Cargo Control
Height Safety
2
COOKES
New Zealand’s Most Extensive Industrial Support Service.
Ashburton
Timaru
Wire Rope Grips Wire Rope Cutters & Swage Tool Pulley Blocks
Section One Section One Section One
Commercial Shackles & Retail Paks Eye Type Hooks Stainless Steel Fittings
Section Two Section Three Section Three
Web Lifting Slings Endless Round Slings Plate Lifting Clamps & Container
Section Four Section Four Lifting Lugs - Section Five
INDEX
Product Code Sheave Dia. Max Wire Rope Max Working Proof Load Weight
Single Sheave (mm) Dia (mm) Load (tonne) (tonne) (kg)
02005603 75 8 0.5 1.0 1.7
02005604 100 10 1.0 2.0 3.2
02005606 150 13 2.0 4.0 8.3
02005608 180 16 3.0 6.0 12.0
Product Code Sheave Dia. Max Wire Rope Max Working Proof Load Weight
Double Sheave (mm) Dia (mm) Load (tonne) (tonne) (kg)
02005703 75 8 0.5 1.0 3.0
02005704 100 10 1.0 2.0 4.7
02005706 150 13 2.0 4.0 13.5
02005708 180 16 3.0 6.0 17.5
Product Code Sheave Dia. Max Wire Rope Max Working Proof Load Weight
(mm) Dia (mm) Load (tonne) (tonne) (kg)
02006155 150 22 5.0 10.0 10.6
Product Code Product Code Model Sheave Dia. Rec. Wire Rope Max Working
Single Sheave Double Sheave (mm) Dia. (mm) Load (tonne)
02003075 02004075 SB4F 100 4-9 1.0
02003100 02004100 SB5F 125 4 - 12 1.5
02003125 02004125 SB6F 150 4 - 14 2.0
02003145 SB7F 175 4 - 16 3.0
Product Code Sheave Dia. Max Wire Rope Max. Pulling Weight
(mm) Dia. (mm) Load (tonne) (kg)
02007125 125 11 8.0 3.0
Product Code Product Code Sheave Dia. Max Rope Dia. Weight Single Weight Double
Single Sheave Double Sheave (mm) (mm) Sheave (kg) Sheave (kg)
09568725 09568726 25 8 0.14 0.22
09568732 09568733 32 10 0.19 0.30
09568750 09568751 50 12 0.40 0.64
Cutting Capacity in mm Ø
Model: C7 C9 C12 C16
Product Code: 02036007 02036009 02036012 02036016
Mild Steel Strands. 7 9 12 16
High tensile steel strands, resistance 160kg/mm². 5 7 8 14
Pre-stressing strand, resistance 190kg/mm². 4 6 6 7
Extra tough wire rope and strands, resistance 210kg/mm². 3 5 5 6
Electrical cables of copper, aluminium and steel-cored
aluminium (ACSR). 7 9 12 16
Range:
>>Commercial Electro-Galvanised
>>Commercial Stainless Steel
>>DIN 1142 Electro-Galvanised
>>FF-C-450 Hot Dip Galvanised
Figure 1.
2) The second wire rope grip must be placed immediately against the thimble but nevertheless in such a
position that the correct tightening of the grip does not damage the outer wires of the rope.
See figure 2.
Turn on the nuts firmly but not yet to the specified torque. *
Figure 2.
3) All other grips must be placed between the first and second grip in such a way that they are separated by
at least one clear grip width from each other.
See figure 3.
Figure 3.
4) Apply light tension to the rope and tighten all nuts to the specified torque.*
* Refer to torque tables listed on pages 13 & 14.
The efficiency of a wire rope termination made with wire rope grips will depend upon their correct
placement on the ropes and the care and skill in the fitting and tightening of the grips.
With inadequately tightened nuts or with an insufficient number of wire rope grips the rope end may draw
through the grips at a very early stage in loading.
A number of factors can adversely affect the tightness of grips upon ropes, such as:
-the nut may be tight on the thread, yet not tight against the bridge.
-contamination of the thread by, for example, dirt and corrosion products, may prevent the correct
tightening of the nut.
Forged wire rope grips provide greater bearing surface and more consistent strength than malleable cast iron
grips.
Malleable cast iron grips should be used only in non-critical applications.
For critical applications only forged wire rope grips are recommended.
Wire rope grips generally to DIN 1142 and commercial wire rope grips must not be used as:
-hoist ropes in mines.
-rope drives for cranes in steel works and rolling mills.
-permanent fastening of ropes in other rope drives.
-rope terminations for load suspension devices in the operation of lifting appliances except in the cases
of lifting tackles where these are produced for a special application and are not reused.
Never use any grip for directly connecting two straight lengths of wire rope.
<----------B---------->
-A
-<
--
<---I--->
>>Finish: Electro-Galvanised
Not Suitable For Lifting Applications
<---H---> <---C--->
<-------F------->
Product Rope Dia Bow Bow Inside Thread Base Base Base
Code (mm) Dia Length Width Length Length Thickness Height
A B C D F H I
02099003 3 4 20 9 12 21 10 10
02099005 5 5 24 11 13 23 11 10
02099006 6 5 28 13 15 26 12 11
02099008 8 6 34 16 19 30 14 15
02099009 10 8 42 19 22 34 18 17
02099013 13 10 55 24 30 42 23 21
02099016 16 12 63 29 33 50 26 26
02099019 19 12 75 32 38 54 29 30
02099022 22 14 85 37 44 61 33 34
02099026 26 14 95 41 45 65 35 37
-- >
<----------B---------->
-A
-<
--
<---I--->
>>Material: U Bolt: Carbon Steel,
<---D--->
Body : Mild Steel
>>Finish: Electro-Galvanised
May only be used with lifting tackle
where these are produced for a special <---H---> <---C--->
application and are not re-used. <-------F------->
Product Rope Dia Bow Bow Inside Thread Base Base Base
Code (mm) Dia Length Width Length Length Thickness Height
A B C D F H I
02100005 5 4 25 12 14 25 13 13
02100006 6.5 5 32 14 17 30 16 14
02100008 8 7 41 18 20 39 20 18
02100010 10 7 46 20 24 40 20 21
02100013 13 11 64 29 29 55 28 29
02100016 16 12 76 34 35 64 32 35
02100019 19 12 83 37 36 68 33 40
02100022 22 14 96 41 40 74 34 44
02100026 26 18 111 46 50 84 38 51
02100030 30 18 127 54 55 95 41 59
02100034 34 22 141 60 60 105 45 67
Wire Rope Dia Min No. of Torque Value Wire Rope Dia Min No. of Torque Value
(mm) Grips (N.m) (mm) Grips (N.m)
5 3 2.0 19 5 68.0
6.5 3 3.5 22 5 107
8 4 6.0 26 5 147
10 4 9.0 30 6 212
13 4 33.0 34 6 296
16 4 49.0
<--------------B-------------->
->
-- A
-- <
-
<-----I----->
>>Drop Forged
>>Material: High Tensile Steel
<-----D----->
>>Finish: Hot Dip Galvanised
<--------H-------> <----C---->
<---------F--------->
Product Rope Dia Bow Bow Inside Thread Base Base Base
Code (in) Dia Length Width Length Length Thickness Height
A (mm) B (mm) C (mm) D (mm) F (mm) H (mm) I (mm)
02101408 5/16 10 45 22 19 43 33 18
02101410 3/8 11 49 26 19 49 42 25
02101411 7/16 12 60 30 25 58 46 26
02101413 1/2 13 61 30 26 58 48 27
02101416 5/8 14 74 33 32 64 52 33
02101419 3/4 16 86 38 37 72 57 37
02101422 7/8 19 98 45 40 80 62 40
02101426 1-0 19 108 48 46 88 67 44
1-1/8 19 117 51 51 91 72 48
1-1/4 22 130 59 54 105 79 56
1-3/8 22 140 60 59 108 79 58
1-1/2 22 147 66 60 112 86 64
1-5/8 26 161 70 67 121 92 67
1-3/4 29 175 78 74 134 97 78
2-0 32 195 86 78 152 113 87
Wire Rope Dia Min No. of Torque Value Wire Rope Dia Min No. of Torque Value
(in) Grips (Ft. Lbs.) (in) Grips (Ft. Lbs.)
5/16 2 30 1-1/8 6 225
3/8 2 45 1-1/4 7 360
1/2 3 65 1-3/8 7 360
5/8 3 95 1-1/2 8 360
3/4 4 130 1-5/8 8 430
7/8 4 225 1-3/4 8 590
1-0 5 225 2-0 8 750
>>Drop Forged
>>Material: High Tensile Steel
>>Finish: Hot Dip Galvanised
G
A
L
C
M E
D B
N
Range:
>>Commercial Galvanised (Generally To DIN 6899-B)
>>Commercial Stainless Steel
>>Hot Dip Galvanised (Generally To BS 464)
>>Solid Cast Self Colour (Generally To DIN 3091)
02105008 7 8 32 20
02105010 9 10 38 24
02105012 13 13 48 30
02105016 16 16 58 36
02105020 20 22 80 50
02105022 22 24 90 56
02105026 26 28 112 70
>>To BS464.
>>Material: Mild Steel
>>Finish: Hot Dip Galvanised
Product Rope Dia. Groove Overall Inside
Code (mm) Width Length Width
A (mm) B (mm) C (mm)
02106008 8 8 54 22
02106009 9 10 64 25
>-A-< >------C-----< 02106011 11 13 73 29
02106013 13 14 80 32
<----------B---------->
02106016 16 16 98 41
<------L------>
02106019 19 21 124 51
02106022 22 22 133 57
02106026 25 27 162 70
02106028 29 29 178 76
02106032 32 33 197 95
02106035 35 38 229 105
02106038 38 41 254 114
02106044 45 51 286 127
02106051 51 64 330 140
02113012 12 13 84 60 20
02113016 16 18 110 80 29
<-d->
>>Thread: Metric
>>Material: Stainless Steel (aisi 304)
>>Finish: Electro-Polished
>>Ends: Jaw + Jaw
Not Suitable For Lifting Applications
Product Code Thread Size Overall Length Hole Dia. Approx.
(mm) (mm) Breaking Load
Max. Min. (kg)
09568545 M5 190 130 5.0 1,000
09568546 M6 210 140 6.0 1,600
09568548 M8 240 165 8.0 3,000
09568550 M10 270 190 9.5 4,000
09568552 M12 360 245 12.0 6,400
09568554 M14 400 270 12.0 8,400
09568556 M16 450 310 14.0 9,600
COOKES Lifting Equipment
COMMERCIAL QUALITY STAINLESS STEEL TURNBUCKLES 19
>>Thread: Metric
>>Material: Stainless Steel (aisi 304)
>>Finish: Electro-Polished
>>Ends: Eye + Eye
Not Suitable For Lifting Applications
Product Code Thread Size Overall Length Approx.
(mm) Breaking Load
Max. Min. (kg)
09568505 M5 160 120 160
09568506 M6 220 150 400
09568508 M8 290 200 800
09568510 M10 360 250 1,200
02201013
02201016
02201019
02201022
02201026
02201029
02201032
02201038
02201045
02201052
Product
Code
>>Thread: Metric
>>Material: Mild Steel
>>Finish: Galvanised
Not Suitable For Lifting Applications
Thread Size Product Code Product Code Product Code Overall Length
Eye + Eye Hook + Eye Hook + Hook (mm)
Max. Min.
M4 02203004 120 71
M5 02203005 02204005 170 115
M6 02203006 02204006 02205006 250 165
M8 02203008 02204008 02205008 260 175
M10 02203009 02204009 02205010 300 210
M12 02203013 02204013 310 220
M16 02203016 410 300
M20 02203019 440 310
M22 02203022 510 370
M24 02203026 600 420
SHACKLES.
INDEX
General.
Commercial shackles are not to be used for lifting purposes.
Should extreme circumstances or shockloading be applicable, this must be taken into account on
selecting the product to be used.
The Working Load Limit (WLL) should be applied in a straight pull and overloads must not be made.
Side-loading should be avoided as the products are not designed for this purpose. If side-loading is unavoid-
able refer to the following:
It is required that the shackles be regularly inspected and that such inspection should take place as a mini-
mum in accordance with the standards given in the country and all relevant requirements of the Rigging
Code of Practice. This is neccessary, because the products in use may be affected by wear, misuse or over-
loading with resulting deformation and alteration of steel structure.
Ensure that the pin is correctly screwed into the shackle eye, i.e. tighten finger tight, then lock using a small
tommy bar or suitable tool so that the collar of the pin is fully seated on the shackle eye.
Ensure that the pin is of the correct length so that it penetrates the full depth of the screwed eye and allows
the collar of the pin to bed on the surface of the shackle eye.
Never replace a shackle pin with a bolt, other than one designed for the purpose, as it may not be suitable for
the loads imposed.
It is important in the case of shackles fitted with a bolt, nut and split cotter pin that the length of the plain
portion of the bolt is such that the nut will jam on the inner end of the thread or on the eyes of the shackle,
and that the rivet on the bolt is cross drilled for a split cotter pin.
Never use a bolt type shackle in operation without using a split cotter pin.
Usage.
When using shackles in conjunction with multi-leg slings, due consideration should be given to the effect of
the angle between the legs of the sling. As the angle increases so does the load in the sling leg and conse-
quently in any shackle attached to that leg.
To avoid eccentric loading of the shackle a loose spacer may be used on either end of the shackle pin or a
shackle with a smaller jaw width should be used.
Do not reduce the width between the shackle jaws by welding washers or spacers to the inside faces of the
eyes or by closing the jaws, as this will have an adverse affect on the mechanical properties of the shackle.
When a shackle is used to secure the top block of a set of rope blocks the load on this shackle is increased by
the value of the hoisting effort.
Avoid applications where due to movement (e.g. of the load or rope) the shackle pin can rotate and possibly
be unscrewed.
Finished shackles may not be heat treated because this may affect the Working Load Limit and the material
structure.
Shackles in use should be subject to thorough examination by a competent person at least every 6 months.
Product WLL Body Dia. Pin Dia. Inside Inside Bow Width Approx
Code (ton) D (mm) d (mm) Width Length 2r (mm) Weight
a (mm) C (mm) (kg)
02325006 0.33 5.0 6 9.5 19.0 16 0.02
02325008 0.50 7.0 8 12.0 29.0 20 0.06
02325009 0.75 9.0 10 13.5 32.0 21 0.11
02325011 1.00 10.0 11 17.0 36.5 26 0.15
02325013 1.50 11.0 12 18.5 43.0 29 0.21
02325016 2.00 13.5 16 22.0 51.0 32 0.37
02325019 3.25 16.0 19 27.0 64.0 43 0.65
02325022 4.75 19.0 22 31.0 76.0 51 1.06
02325026 6.50 22.0 25 36.0 83.0 58 1.56
02325028 8.50 25.0 28 43.0 95.0 68 2.32
02325032 9.50 28.0 32 47.0 108.0 75 3.28
02325035 12.00 32.0 35 51.0 115.0 83 4.51
02325038 13.50 35.0 38 57.0 133.0 92 5.93
02325042 17.00 38.0 42 60.0 146.0 99 7.89
02325051 25.00 45.0 50 74.0 178.0 126 13.40
02325057 35.00 50.0 57 83.0 197.0 138 18.85
02325065 42.50 57.0 65 95.0 222.0 160 26.06
55.00 65.0 70 105.0 254.0 180 37.86
85.00 75.0 80 127.0 330.0 190 58.68
Product WLL Body Dia. Pin Dia. Inside Inside Bow Approx
Code (ton) D (mm) d (mm) Width Length Width Weight
a (mm) C (mm) 2r (mm) (kg)
1.50 11.0 12 18.5 43.0 29 0.25
02329016 2.00 13.5 16 22.0 51.0 32 0.44
02329019 3.25 16.0 19 27.0 64.0 43 0.79
02329022 4.75 19.0 22 31.0 76.0 51 1.26
02329026 6.50 22.0 25 36.0 83.0 58 1.88
02329029 8.50 25.0 28 43.0 95.0 68 2.78
02329032 9.50 28.0 32 47.0 108.0 75 3.87
02329035 12.0 32.0 35 51.0 115.0 83 5.26
02329038 13.50 35.0 38 57.0 133.0 92 6.94
02329042 17.00 38.0 42 60.0 146.0 99 8.79
02329051 25.00 45.0 50 74.0 178.0 126 14.99
02329057 35.00 50.0 57 83.0 197.0 138 20.65
02329070 55.00 65.0 70 105.0 254.0 180 41.05
02329080 85.00 75.0 80 127.0 330.0 190 62.24
Available to 120 ton WLL on indent basis.
Product Product WLL Body Dia. Pin Dia. Inside Inside Approx
Code Code (ton) D (mm) d (mm) Width Length Weight
Self Colour Galvanised a (mm) C (mm) (kg)
02301009 02302009 0.25 6 10 13 25 0.11
02301013 02302013 0.50 10 13 19 38 0.17
02301016 02302016 0.75 13 16 29 54 0.35
02301019 02302019 1.50 16 19 32 64 0.66
02301022 02302022 2.00 19 22 38 73 1.02
02301026 02302026 3.00 22 25 44 83 1.57
02301029 3.75 25 28 51 95 2.30
02301032 5.00 28 32 54 105 3.20
02301035 6.00 32 35 60 114 4.30
02301038 7.00 35 38 67 127 5.40
02301044 9.50 38 45 70 137 6.80
02301048 11.25 42 48 76 146 8.70
02301051 13.00 45 51 83 156 11.00
14.25 48 54 92 178 14.30
16.25 51 57 98 187 20.00
18.00 54 60 105 197 26.38
20.00 57 64 108 210 28.27
25.00 64 73 121 235 35.00
30.00 70 79 133 260 49.03
35.00 76 86 146 279 63.56
40.00 79 89 149 292 71.73
50.00 89 102 171 330 101.24
65.00 102 114 191 375 150.73
80.00 114 127 219 419 214.74
Product Code Product Code Pin & Body Dia. Inside Width Inside Length Approx Weight
(Loose) (Display Pack) d & D (mm) a (mm) C (mm) per 100 pcs (kg)
02300005 02300905 5 10 19 1.9
02300006 02300906 6 12 24 3.4
02300008 02300908 8 16 32 7.0
02300009 02300909 10 20 40 13.0
02300013 02300913 12 25 48 24.0
02300016 16 32 64 50.0
02300019 20 38 76 80.0
02300022 22 44 85 130.0
02300026 25 50 95 200.0
Product Code Pin & Body Dia. Working Load Overall Length Approx Weight
(mm) (Ton) (mm) (kg)
09568405 5 .04 32 .02
09568406 6 .10 36 .03
09568408 8 .20 48 .06
09568410 10 .30 58 .12
09568412 12 .50 70 .19
09568416 16 .80 95 .41
Product Working Body Dia. Pin Dia Inside Inside Dee Type
Code Load D d Width Length
Limit (mm) (mm) a C
(tons) (mm) (mm)
02314216 2.00 13 16 22 43
02314219 3.25 16 19 27 51
02314222 4.75 19 22 31 59
02314225 6.50 22 25 36 73
02314228 8.50 25 28 43 85
02314232 9.50 28 32 47 90
02314235 12.00 32 35 51 94
02314238 13.50 35 38 57 115
02314242 17.00 38 42 60 127
25.00 45 50 74 149
Bow Type Product Working Body Dia. Pin Dia Inside Inside Width
Code Load D d Width Length of Bow
Limit (mm) (mm) a C 2r
(tons) (mm) (mm) (mm)
2.00 13 16 22 51 32
3.25 16 19 27 64 43
4.75 19 22 31 76 51
6.50 22 25 36 83 58
02314329 8.50 25 28 43 95 68
02314332 9.50 28 32 47 108 75
02314335 12.00 32 35 51 115 83
02314338 13.50 35 38 57 133 92
02315342 17.00 38 42 60 146 99
25.00 45 50 74 178 126
INDEX
Approx.
Product Code Breaking Load Overall Length Eye I.D.
(kg) (mm) (mm)
09564740 3,550 89 18
Approx.
Product Code Breaking Load Overall Length Eye I.D.
(kg) (mm) (mm)
09564745 3,405 131 24.41
Approx.
Product Code Breaking Load Overall Length Eye I.D.
(kg) (mm) (mm)
09564735 3,405 135 26.1
“S” HOOKS
Product Code Pin & Body Dia. Working Load Overall Length Approx Weight
(mm) (Ton) (mm) (kg)
09568405 5 .04 32 .02
09568406 6 .10 36 .03
09568408 8 .20 48 .06
09568410 10 .30 58 .12
09568412 12 .50 70 .19
09568416 16 .80 95 .41
>>Thread: Metric
>>Material: Stainless Steel (aisi 304)
>>Finish: Electro-Polished
>>Ends: Eye + Eye
Not Suitable For Lifting Applications
Product Code Thread Size Overall Length Approx.
(mm) Breaking Load
Max. Min. (kg)
09568505 M5 160 120 160
09568506 M6 220 150 400
09568508 M8 290 200 800
09568510 M10 360 250 1,200
>>Thread: Metric
>>Material: Stainless Steel (aisi 304)
>>Finish: Electro-Polished
>>Ends: Jaw + Jaw
Not Suitable For Lifting Applications
Product Code Thread Size Overall Length Hole Dia. Approx.
(mm) (mm) Breaking Load
Max. Min. (kg)
09568545 M5 190 130 5.0 1,000
09568546 M6 210 140 6.0 1,600
09568548 M8 240 165 8.0 3,000
09568550 M10 270 190 9.5 4,000
09568552 M12 360 245 12.0 6,400
09568554 M14 400 270 12.0 8,400
09568556 M16 450 310 14.0 9,600
Product Code Product Code Sheave Dia. Max Rope Dia. Weight Single Weight Double
Single Sheave Double Sheave (mm) (mm) Sheave (kg) Sheave (kg)
09568725 09568726 25 8 0.14 0.22
09568732 09568733 32 10 0.19 0.30
09568750 09568751 50 12 0.40 0.64
INDEX
Sling No. of
Width Plys
(mm)
100 One 2.00 1.60 2.80 4.00 4.00 3.20 5.60 8.00
Two 4.00 3.20 5.60 8.00 8.00 6.40 11.20 16.00
125 One 2.50 2.00 3.50 5.00 5.00 4.00 7.00 10.00
Two 5.00 4.00 7.00 10.00 10.00 8.00 14.00 20.00
150 One 3.00 2.40 4.20 6.00 6.00 4.80 8.40 12.00
Two 6.00 4.80 8.40 12.00 12.00 9.60 16.80 24.00
200 One 4.00 3.20 5.60 8.00 8.00 6.40 11.20 16.00
Two 8.00 6.40 11.20 16.00 16.00 12.80 22.40 32.00
300 One 6.00 4.80 8.40 12.00 RA6 special purpose designs
Two 12.00 9.60 16.80 24.00 available on application
Metal Dee (Plain and Reduced Eye Reduced and Reversed Flat Eye
Choker) Where small hooks are Eye Where minimum
Best suited to lifts where used. For choker lift. Gives clearance is required for
eyes get excessive wear. square lift to load on passing under load and
same plane as webbing. for use with lifting beams.
RA5 RA6
4. Do not use sling if there is any sign of cut webbing, snagging, heat or chemical
damage, excessive wear, damaged seams, any other defects or presence of grit,
abrasive materials or other deleterious matter.
6. Protect sling webbing from sharp edges of load. Use protective sleeves.
10. Never attempt to repair a damaged sling. Always refer sling to a certified
manufacturer.
Supra Roundslings
Features: • Colour Coded
• Light Weight
• 4 Times The Life of Standard Roundslings
• Working Load Limit Woven In
• Increased Sleeve Thickness by 40%
• Width Reduced 30% to Improve Handling
• Improved Sliding Effect When Choked
• Proof Load Certificate Supplied With Every Sling
Type WLL (kg) WLL (kg) WLL (kg) WLL (kg) WLL (kg)
Vertical Choke Basket 90° 120°
Supra 1000 1,000 800 2,000 1,400 1,000
Supra 2000 2,000 1,600 4,000 2,800 2,000
Supra 3000 3,000 2,400 6,000 4,200 3,000
Supra 4000 4,000 3,200 8,000 5,600 4,000
Supra 5000 5,000 4,000 10,000 7,000 5,000
Supra 6000 6,000 4,800 12,000 8,400 6,000
Supra 8000 8,000 6,400 16,000 11,200 8,000
Supra 10000 10,000 8,000 20,000 14,000 10,000
1,000 kg WLL. Colour Code: Violet 2,000 kg WLL. Colour Code: Green
Product Code Effective Length* Product Code Effective Length*
(m) (m)
09301050 0.5 09302100 1.0
09301100 1.0 09302150 1.5
09301150 1.5 09302200 2.0
09301200 2.0 09302250 2.5
09301250 2.5 09302300 3.0
09301300 3.0 09302350 3.5
09301350 3.5 09302400 4.0
09301400 4.0 09302500 5.0
09301450 4.5 09302600 6.0
09301500 5.0
09301600 6.0
* Stock lengths, other sizes on indent * Stock lengths, other sizes on indent
3,000 kg WLL. Colour Code: Yellow 4,000 kg WLL. Colour Code: Grey
Product Code Effective Length* Product Code Effective Length*
(m) (m)
09303100 1.0 09304100 1.0
09303150 1.5 09304150 1.5
09303200 2.0 09304200 2.0
09303250 2.5 09304250 2.5
09303300 3.0 09304300 3.0
09303350 3.5 09304350 3.5
09303400 4.0 09304400 4.0
09303500 5.0 09304500 5.0
09303600 6.0 09304600 6.0
* Stock lengths, other sizes on indent * Stock lengths, other sizes on indent
5,000 kg WLL. Colour Code: Red 6,000 kg WLL. Colour Code: Brown
Product Code Effective Length* Product Code Effective Length*
(m) (m)
09305200 2.0 09306200 2.0
09305250 2.5 09306300 3.0
09305300 3.0 09306400 4.0
09305400 4.0 09306500 5.0
09305500 5.0 09306600 6.0
09305600 6.0
* Stock lengths, other sizes on indent * Stock lengths, other sizes on indent
8,000 kg WLL. Colour Code: Blue 10,000 kg WLL. Colour Code: Orange
Product Code Effective Length* Product Code Effective Length*
(m) (m)
09308300 3.0 09310300 3.0
09308400 4.0 09310400 4.0
09308600 6.0 09310500 5.0
09310600 6.0
* Stock lengths, other sizes on indent
* Stock lengths, other sizes on indent
NOTE: Types/lengths listed are those carried as standard stock lines in New Zealand. Supra Roundslings
up to 10,000 kg WLL and Economy Roundslings up to 30,000 kg WLL imported to order.
LIFTING EQUIPMENT.
INDEX
Before using the clamp always read the instruction manual supplied with the clamp.
Before using the clamp always read the instruction manual supplied with the clamp.
ALSO AVAILABLE
<< IPVK
Drum Clamps
LTTK >>
Beam Clamps
Product Code Model WLL Set of 4 Chain Angle Type Weight Set of 4
(t) (kg)
09115006 MKIIa 56 Vertical Top Lifting 28
09115007(LH) MKVa 40 36° Bottom Lifting 18
09115008(RH) MKVa 40 36° Bottom Lifting 18
09115007(LH) MKVa 32 50° Bottom Lifting 18
09115008(RH) MKVa 32 50° Bottom Lifting 18
al
se ng on
ld di ti
fo a e c
y!
4- lo -dir
rit
cu
ti
ul
M
* Note: For lashing purposes the above working load limits may be doubled to determine the lashing
capacity.
al
se ng on
ld di ti
fo a e c
y!
4- lo -dir
rit
cu
ti
ul
M
* Note: For lashing purposes the above working load limits may be doubled to determine the lashing
capacity.
al
se ng on
ld di ti
fo a e c
y!
4- lo -dir
rit
cu
ti
ul
M
* Note: For lashing purposes the above working load limits may be doubled to determine the lashing
capacity.
1) The SWIFTLIFT concrete lifting system provides a simple, safe and rapid method of lifting and
handling precast concrete elements.
It has been used extensively throughout the world for more than 10 years and the system has proved
it’s versatility, operational simplicity and safety in a wide range of applications.
The system was originally developed to overcome the need to use potentially dangerous and time
consuming threaded connectors. It also provides the most cost-effective solution to lifting problems in
the majority of cases, including difficult applications requiring complex tilting and turning
movements.
Full approval has been granted for the use of this system by the regulatory statutory authorities in
every state of Australia and in New Zealand.
2) Universal Lifting Eyes can be employed for all normal lifting applications and incorporate a remote
detachment feature useful for tilt-up applications.
Product SWL a b c d e f i j k
Code (t) (mm) (mm) (mm) (mm) (mm) (mm) (mm) (mm) (mm)
09110130 1.3 47.5 75 71 56 55.0 33 164 12 21
09110250 2.5 64.0 98 95 68 70.0 42 205 14 25
09110500 5.0 70.0 118 90 88 86.0 57 237 17 38
10.0 95.0 160 121 112 117.5 73 348 25 51
20.0 118.0 186 150 152 155.0 110 441 33 74
32.0 175.0 269 189 195 214.0 153 584 40 100
<--H--> <--G-->
>>Tested & Certified
>>Manufactured In The U. K.
<---B--->
<--H--><--G-->
>>Tested & Certified
>>Manufactured In The U. K.
<---B--->
EYEBOLTS
Features:
• High tensile, heat treated, forged material 1.6541. 100%
electromagnetic crack detection. Complies with DIN 5691 and
EN 1677.
• Side loading permissible when adjusted to the correct plane.
• Countersunk socket screw quality: Grade 10.9 metric coarse
pitch.
• Also Available in UNC thread sizes.
• 4:1 safety factor on Working Load Limit.
• Countersunk socket screw held captive.
• Shape: star shaped (clearly distinguishible from other collared
eyebolts).
• Colour: fluorescent pink powder coating.
• Marking: clear indication of the WLL for the side loading
direction F.
• Patent pending.
• Installation:
• Engage key in hexagonal socket screw and screw
eyebolt into position. Fitting by hand ensures easy
removal.
• For rotation when eyebolt is fully engaged, disengage key
from socket screw.
• Design information available on CAD.
C F1
RM HIGH TENSILE EYENUT
D Metric Coarse Thread.
F2
A
Product Code Description WLL - F1 WLL - F2 A (mm) C (mm) D (mm) Weight (kg)
RM-M6 0.4t 0.1t 35 10 25 0.10
RM-M8 0.8t 0.2t 35 10 25 0.10
09104310 RM-M10 1.0t 0.25t 35 10 25 0.10
09104312 RM-M12 1.6t 0.4t 41 12 30 0.16
RM-M14 3.0t 0.75t 48 14 35 0.27
09104316 RM-M16 3.2t 0.8t 48 16 35 0.25
09104320 RM-M20 6.0t 1.5t 55 20 40 0.40
09104324 RM-M24 8.0t 2.0t 70 20 50 0.72
RM-M30 12.0t 3.0t 85 24 60 1.33
RM-M36 16.0t 4.0t 130 43 100 5.70
RM-M42 24.0t 6.0t 130 43 100 5.60
RM-M48 32.0t 8.0t 130 43 100 5.50
INDEX
SPECIFICATIONS
Safe Working Load 500 kg 1t 1.5t 2t 3t 5t 10 t
Standard Lift 3m 3m 3m 3m 3m 3m 3m
Falls of Chain 1 1 1 1 2 2 4
Effort to lift S.W.L. 23kg 30kg 32kg 35kg 27kg 41kg 39kg
Net weight 10kg 12kg 13kg 22kg 32kg 46kg 68kg
Load chain diameter 6mm 6mm 8mm 8mm 8mm 10mm 10mm
CLEARANCE DIMENSIONS (mm)
A (Headroom) 270 317 399 414 465 636 750
B (Width) 127 158 187 187 210 253 373
C (Depth) 131 140 161 161 161 161 184
Hook opening (upper) 30 28 36 33.5 40 50 64
Hook opening (lower) 30 28 36 33.5 40 50 64
PRODUCT CODES
500 kg 1t 1.5 t 2t 3t 5t 10 t
Specifications and dimensions for 20 t 10961050 10961100 10961150 10961200 10961300 10961500 10961110
available on request.
DIMENSIONS
SPECIFICATIONS
Safe Working Load tonnes 0.50 t 0.75 t 1.5t 3t 6t
Standard Lift m 1.5m 1.5m 1.5m 1.5m 1.5m
Test load kN 6.25 11.03 22.05 37.50 75
Headroom H mm 260 325 380 480 620
Falls of chain 1 1 1 1 2
Load chain Dia. mm 5 6 8 10 10
Lever length D mm 300 280 410 410 410
A 105 148 172 200 200
Clearance mm B 78 90 98 115 115
C 80 136 160 180 235
Net Weight kg 4 7 11 21 31
Product Code 10962050 10962075 10962150 10962300 10962600
Code 02046011
Code 02046101
Code 02046031
Code 02046051
Code 02046151
Details: Small, robust, Small, robust, Medium size Heavy duty, twin Extra heavy
zinc plated, ideal zinc plated, gear gear driven ratio gearing. duty. Ideal for
for small craft driven recom- winch recom- Ideal for larger larger craft.
mended for light mended for craft craft.
boats up to 14 ft. 14 - 19 ft.
50 mm Webbing Width.
>> Seatbelt type webbing with 1,500 kg breaking load helps prevent ‘crossover’
whenlaying onto winch drum.
>> Standard lengths 4, 5 or 6 metres. Special lengths manufactured to order.
>> Available with wire rope tail to fit N. Z. manufactured winch or eye to fit
Cookes imported winch. Refer below.
(a) With wire rope tail and stainless steel ‘S’ hook (suits N. Z. manufactured winch).
4 metre: Product code 09582400
5 metre: 09582500
6 metre: 09582600
(b) With eye and galvanised snap hook (suits Cookes imported winch).
4 metre: Product code 09582405
5 metre: 09582505
6 metre: 09582605
SPECIFICATIONS
Special Features:
HW-1500
Worm drive non-brake model.
SF-2200 >
Ideal for use in confined locations, the ratchet
handle permits reciprocating handle movement in
both directions for hoisting and lowering loads
INDEX
KUPLEX 8+10
Testing:
KUPLEX 8+10 components are subjected to both 100%
non-destructive testing and 100% proof load testing giving
the user complete peace of mind.
KUPLEX Grade 80 and Grade 100 chains are subjected to
100% non-destructive tests with calibration and magnetic
sorting bridge prior to a final proof load test and visual
inspection.
Chain Dia Single Leg Two Leg Slings Three & Four Leg Slings Endless
(mm) Slings 0 - 45° 45 - 60º 0 - 45° 45 - 60º Slings in
/Grade Factor 1.4 Factor 1.0 Factor 2.1 Factor 1.5 Choke Hitch
Factor 1.6
7/80 1.50 2.12 1.50 3.15 2.24 2.50
7/100 2.00 2.80 2.00 4.20 3.00 3.20
8/80 2.00 2.80 2.00 4.20 3.00 3.20
10/80 3.15 4.25 3.15 6.70 4.75 5.00
10/100 4.00 5.60 4.00 8.40 6.00 6.40
13/80 5.30 7.50 5.30 11.20 8.00 8.50
13/100 6.70 9.50 6.70 14.00 10.00 10.70
16/80 8.00 11.20 8.00 17.00 11.80 12.50
16/100 10.00 14.00 10.00 21.20 15.00 16.00
19/80 11.20 16.00 11.20 23.60 17.00 18.00
19/100 14.00 20.00 14.00 30.00 21.00 22.40
23/80 16.00 23.60 16.00 35.50 25.00 26.50
23/100 21.00 29.50 21.00 44.00 31.50 33.50
26/80 21.20 30.00 21.20 45.00 31.50 33.50
26/100 27.00 38.00 27.00 57.00 40.00 43.00
32/80 31.50 45.00 31.50 67.00 47.50 50.00
32/100 40.00 56.00 40.00 85.00 60.00 65.00
The Working Load Limits (WLL) listed in the table will have a WLL 1.4 times that of a single leg sling
above are the maximum weights which slings are when used vertically, and not two times the single
designed to sustain in General Lifting Service ac- leg. That same WLL applies to all angles from 0º -
cording to the standard uniform load method of 45º (0º - 90º included angle). Where there is likely to
rating. be a need to use a sling at an angle greater than 45º
In exceptionally hazardous conditions or in any from the vertical, the sling should have additional
other circumstances which might indicate a need for markings showing the reduced WLL applying at
a WLL lower than the designed figure, the degree of angles from 45º to 60º from the vertical (included
hazard should be assessed by a competent person angles from 90º to 120º)
and the working load limit adjusted accordingly. The
WLL, which should be marked on the sling itself or An alternative method of rating may be used for a
on a securely fixed metal tag, must not be exceeded specific lifting application where the angle at which
in any circumstances. the sling legs are disposed is predetermined. This
THE LOAD IMPOSED ON A SLING LEG IN- method allows greater working load limits at angles
CREASES AS THE ANGLE OF THE LEG FROM less than 45º from the vertical, always assuming that
THE VERTICAL INCREASES. Account is taken of the sling legs are disposed symmetrically with each
this fact when calculating working load limits. For leg accepting an equal share of the load to be lifted.
example, a 10mm two-leg sling to be used at an For further details refer to your nearest Cookes
angle of 45º from the vertical (90º included angle) branch
Single-leg with Single-leg with Collar sling with Collar sling with Two-leg with Two-leg with
master link and Kuplink and egg link each Kuplink each master link and shortening
hook hook end end hooks clutches
<-----P----->
<------W2------>
>--W1--<
>--D--<
Test Requirements and Working Load Limits. Bend and Tensile Test as Specified in EN 818-2
KUPLEX Grade 80 Chain. Colour Coded Black. Size Minimum Number of
Size Min Manufac- Working mm Bend Samples per
mm Breaking turing Load Limit Deflection 200m Lot
Force Proof Force (tonnes) (mm)
(kN) (kN) 6 4.8 3
7 61.6 38.5 1.50 7 5.6 2
8 78.4 49.0 2.00 8 6.4 2
10 126 78.5 3.15 10 8.0 2
13 214 133 5.30 13 10 2
16 322 201 8.00 16 13 2
19 454 284 11.20 19 15 1
23 666 415 16.00 23 18 1
26 850 531 21.20 26 21 1
32 1,290 804 31.50 32 26 1
Mean Stress
N/mm²: 800 500 200 Single link samples are taken from a lot size of 200m and bent
Factor: 4 2.5 1 to a minimum deflection as specified in the table above.
Following removal of the force, the link is examined by a
KUPLEX Grade 10 Chain & Components. competent person. The link has to withstand the specified
Colour Coded Gold (Chain) Red (Components). deflection for that diameter without any visible defects.
7 77 49 2 Tensile Test.
10 158 98 4 Samples of chain as specified above, and in finished condition,
13 266 166 6.7 are subjected to a static tensile test and have to meet the
16 402 251 10 minimum breaking force requirements as stated in the adjacent
19 567 354 14 table, with a total ultimate elongation of not less than 20%.
23 831 519 21 Parsons Chain Routine Component Sampling.
26 1,062 664 27 All KUPLEX components are routinely verified with tensile
32 1,609 1,005 40 and fatigue testing. This is a Parsons Chain Company internal
Mean Stress specification, above and beyond any current National or
N/mm²: 1,000 625 200 International Standards requirement.
Factor: 4 2.5 1
WARNING NEVER EXCEED THE
WORKING LOAD LIMIT STATED
Kuplex Kuplink KS
Alternative master link for single leg slings dispensing with a need for a Kupler.
Kuplex Kupler K
This component is used for joining chain to the top link.
Product Type/ WLL R W DxS Weight
Code Size Ref (t) (mm) (mm) (mm) (kg)
02403907 K7N 2.00 60 26 12 x 10 0.15
02403910 K10N 4.00 73 35 19 x 15 0.47
02403913 K13N 6.70 95 45 25 x 22 1.01
02403916 K16N 10.00 118 54 28 x 23 1.66
02403919 K19N 14.00 134 64 34 x 28 2.78
02403923 K23 21.00 121 64 41 x 38 4.26
02403926 K26 27.00 140 82 64 x 51 13.14
NOTES
Items Listed Are Those Generally Carried In New Zealand By Cookes.
Other Items Are Available On Indent - Contact Your Nearest Cookes Branch For A Complete Kuplex
User Guide Which Shows The Full Product Range.
All Fittings Are Supplied With One Load Pin And Two Retaining Pins.
Spare Pins Are Available As Follows:
Size Spare Load Pin Spare Retaining Pin Size Spare Load Pin Spare Retaining Pin
(mm) Product Code Product Code (mm) Product Code Product Code
7 02416007 02415007 19 02416019 02415019
10 02416010 02415010 23 02416023 02415023
13 02416013 02415013 26 02416026 02415026
16 02416016 02415016
Chain Dia Single Leg Two Leg Slings Three & Four Leg Slings Endless
(mm) Slings 0 - 45° 45 - 60º 0 - 45° 45 - 60º Slings in
Factor 1.4 Factor 1.0 Factor 2.1 Factor 1.5 Choke Hitch
Factor 1.6
6 1.12 1.60 1.12 2.36 1.70 1.80
7 1.50 2.12 1.50 3.15 2.24 2.50
8 2.00 2.80 2.00 4.25 3.00 3.15
10 3.15 4.25 3.15 6.70 4.75 5.00
13 5.30 7.50 5.30 11.20 8.00 8.50
16 8.00 11.20 8.00 17.00 11.80 12.50
18 10.00 14.00 10.00 21.20 15.00 16.00
19 11.20 16.00 11.20 23.60 17.00 18.00
20 12.50 17.00 12.50 26.50 19.00 20.00
22 15.00 21.20 15.00 31.50 22.40 23.60
23 16.00 23.60 16.00 35.50 25.00 26.50
26 21.20 30.00 21.20 45.00 31.50 33.50
32 31.50 45.00 31.50 67.00 47.50 50.00
The Working Load Limits (WLL) listed in the table will have a WLL 1.4 times that of a single leg sling
above are the maximum weights which slings are when used vertically, and not two times the single
designed to sustain in General Lifting Service ac- leg. That same WLL applies to all angles from 0º -
cording to the standard uniform load method of 45º (0º - 90º included angle). Where there is likely to
rating. be a need to use a sling at an angle greater than 45º
In exceptionally hazardous conditions or in any from the vertical, the sling should have additional
other circumstances which might indicate a need for markings showing the reduced WLL applying at
a WLL lower than the designed figure, the degree of angles from 45º to 60º from the vertical (included
hazard should be assessed by a competent person angles from 90º to 120º)
and the working load limit adjusted accordingly. The
WLL, which should be marked on the sling itself or
on a securely fixed metal tag, must not be exceeded An alternative method of rating may be used for a
in any circumstances. specific lifting application where the angle at which
THE LOAD IMPOSED ON A SLING LEG IN- the sling legs are disposed is predetermined. This
CREASES AS THE ANGLE OF THE LEG FROM method allows greater working load limits at angles
THE VERTICAL INCREASES. Account is taken of less than 45º from the vertical, always assuming that
this fact when calculating working load limits. For the sling legs are disposed symmetrically with each
example, a 10mm two-leg sling to be used at an leg accepting an equal share of the load to be lifted.
angle of 45º from the vertical (90º included angle) For further details refer to your nearest Cookes
branch
Single & multi-leg slings with shortening clutches & sling hooks
<-----P----->
<------W2------>
>--W1--<
>--D--<
Size Minimum Manufacturing Working Load
(mm) Breaking Force Proof Force Limit
(kN) (kN) (t)
7 61.6 38.5 1.50
10 126.0 78.5 3.15
13 212.0 133.0 5.30
16 322.0 201.0 8.00
20 503.0 314.0 12.50
NOTES
Items Listed Are Those Generally Carried In Stock By Cookes.
Other Items Are Available On Indent.
For Further Items Ask At Your Nearest Cookes Branch For A Copy Of
Weissenfels Brochure “Weissalloy 125”
NOTES
Items Listed Are Those Generally Carried In Stock By Cookes.
Other Items Are Available On Indent.
For Further Items Ask At Your Nearest Cookes Branch For A Copy Of The
Yoke Grade 80 brochure.
“DO’S”
1. Check the condition of the slings before each load.
2. Check that the chain legs are not twisted.
3. Check that the load is on the centre of the hook and not on the tip.
“DON’TS”
1. Do not carry out self-repairs and weldings of the chains and fittings.
2. Do not use the slings loaded over the maximum permissible load.
3. Do not load with convergence angle over 120°.
4. Do not shock load.
5. Do not shorten the chains by knotting them.
6. Do not paint or galvanize the chains.
7. Do not use chains in pickling or acid baths.
8. Do not submit the chains to heat treatment.
9. Do not use chain and accessories outside of temperature range
between -40°C and +200°C.
INDEX
Features:
Ö On Wheels for Ease of Movement.
Ö Front Wheels Lock for Stability.
Ö Built-in Measured Metre.
Ö High Quality Powder Coated Finish.
Ö Hang Hooks for Chain Ends.
Ö Top Shelf for Bolt Cutter Storage.
Provided Free of Charge to Approved
Resellers. (Remains Cookes Property)
• Zinc Plated
Not Suitable For Lifting Applications
Product To Suit Overall
Code Chain Size Length
(mm) (mm)
02643108 8.0 43.0
02643110 10.0 51.0
Product Code Product Code Recommended Min. Breaking Take Up Approx. Weight
(Grab Hooks) (Claw Hooks) Chain Size (mm) Load (kg) (mm) (kg)
09026006 6.0 3,650 61 1.15
09026009 09026909 7.3 - 8.0 8,615 114 3.20
09026013 09026910 10.0 12,700 114 5.65
8 02400908 8 24 28
10 02400910 10 30 34
13 02400913 13 39 50
16 02400916 16 48 55
Chain Size Product Nominal Pitch Max. External Min Internal Approx. Weight
(Diameter) mm Code mm Width (mm) Width (mm) kg/m
>> All stud link chains & components are supplied with Lloyds Certification.
>> Imported to order in lengths of 27.5 metres.
Common Link (C) Joining Shackle (JS) Chain Locker Shackle (CS)
>> Suitable for both boat mooring and mussell farm use, second hand stud link chain is generally stocked
in sizes 26mm through to 45mm diameter.
>> Sizes and quantities on hand are dependant on worldwide availability and fluctuate accordingly.
Contact your nearest Cookes branch to ascertain current stockholding.
>> Second hand stud link chain will be cut to required length/s.
INDEX
This Chain Meets The Requirements of AS/NZS4344. For self colour chain options refer
Hi-Freight chain on page 89
Not Suitable For Lifting Applications
GRADE 70 CLEVIS GRAB HOOKS
>>Material: Forged Alloy Steel (Grade 70)
>>Finish: Yellow Zinc Plated
>>Suitable For Use With Grade 70 Transport Chain
Conforming to AS/NZS 4344:1995
Product Code To Suit Chain Dia. Lashing Capacity
(mm) (kg)
02234206 6.0 1,700
02234208 7.3 - 8.0 3,000
02234209 10.0 4,500
02234213 12.5 - 13.0 6,700
Not Suitable For Lifting Applications
Product Code Product Code Recommended Min. Breaking Take Up Approx. Weight
(Grab Hooks) (Claw Hooks) Chain Size (mm) Load (kg) (mm) (kg)
09026006 6.0 3,650 61 1.15
09026009 09026909 7.3 - 8.0 8,615 114 3.20
09026013 09026910 10.0 12,700 114 5.65
SAFETY
Instructions For Use & Care
WARNINGS
Lever Type Load Binders
Hook loadbinder to chain so you can operate it while standing on the ground.
Position load binder so it’s handle can be pulled downward to tighten chain
(see photo). Be aware of ice, snow, rain, oil, etc. that can affect your
footing. Make certain your footing is secure.
If the above recommendation is disregarded and a cheater pipe is used, it must closely fit the handle and
must slide down the handle until the handle projections are contacted. The pipe should be secured to the
handle, for example by a pin, so that the pipe cannot fly off the handle if you lose control and let go.
The increased leverage, by using a cheater pipe, can cause deformation and failure of the chain and
loadbinder.
During and after tightening chain, check load binder handle position. Be sure it is in the locked position and
that it’s bottom side touches the chain link.
Chain tension may decrease due to load shifting during transport. To be sure the load binder remains in
proper position: Secure handle to chain by wrapping the loose end of chain around the handle and the tight
chain or tie handle to chain with soft wire.
When releasing load binder, remember there is a great deal of energy in the stretched chain. This will cause
the load binder handle to move very quickly with great force when it is unlatched. Move handle with cau-
tion. It may whip - keep body clear.
Never use a cheater pipe or handle extender to release handle. Use a steel bar and pry under the handle
and stay out of the path of the handle as it moves upward.
If you release the handle by hand, use an open hand under the handle and push upward. Do not close your
hand around the handle. Always keep yourself out of the path of the moving handle.
Routinely check load binders for wear, bending, cracks, nicks or gouges. If bending or cracks are present -
Do not use the load binder.
Routinely lubricate pivot and swivel points of lever binders and pawl part and screw threads of ratchet
binders to extend product life and reduce friction wear.
al
se ng on
ld di ti
fo a e c
y!
4- lo -dir
rit
cu
ti
ul
M
al
se ng on
ld di ti
fo a e c
y!
4- lo -dir
rit
cu
ti
ul
M
al
se ng on
ld di ti
fo a e c
y!
4- lo -dir
rit
cu
ti
ul
M
Plastic Cornerboards
Heavy Duty Ridged Plastic (Light Blue)
1.2 metre x 170 mm x 100 mm.
Product Code: 09567101
Chain Plates
• Heavy Duty Galvanised Steel
These banners were designed for Cookes with Special strong, durable
assistance from the Land Transport Safety ‘Supersign’ PVC material.
Authority.
They are manufactured using special strong, Eyelets
durable ‘supersign’ PVC and a special ink
process ensuring long life with minimum fade. Rope ties
Do not be fooled by cheap polyester material
imitations.
Spare Tailstrap
• 0.4 metre Length*
Product Code: 09570701
Spare Mainstrap
• 8.0 metre Length*
Product Code: 09570950
Spare Tailstrap
• 0.4 metre Length*
Product Code: 09570970
Spare Tailstrap
• 0.4 metre Length*
Product Code: 09571761
Double J Hook
• 11mm Material Diameter
Product Code: 09564022
Flat Hook
• Minimum Breaking Load 3,000kg.
Product Code: 09564621
Anchor Bracket
• Twin Slot, Black Powder Coated
Product Code: 09564921
Spare Mainstrap
• 6.0 metre Length*
Product Code: 09576916
Spare Tailstrap
• 0.4 metre Length*
Product Code: 09576920
Double J Hook
• 8mm Material Diameter
• Minimum Breaking Load 1,400kg.
Product Code: 09564012
Flat Hook
• Minimum Breaking Load 2,500kg.
Product Code: 09564611
Spare Tailstrap
• 0.2 metre Length*
Product Code: 09574901
Spare Mainstrap
• 4.0 metre Length*
Product Code: 09574944 Webbing Colour
Royal Blue
Spare Tailstrap
• 0.2 metre Length*
Product Code: 09574903
Spare Mainstrap
• 4.0 metre Length*
Product Code: 09574940
Spare Tailstrap
• 0.2 metre Length*
Product Code: 09574901
Spare Cambuckle
Product Code: 09563201 (Cast)
or 09563204 (Steel)
* Special Lengths Manufactured to Order.
** Refer Page 98 For Alternative End Fittings.
For User Instructions Refer Page 116.
Flat Hook
• Minimum Breaking Load 300kg.
Product Code: 09564601
Anchor Bracket
• Single Slot, Zinc Plated
Product Code: 09564901
Instructions For Care and Use of Your Cookes Ratchet Tiedown Restraint
To ensure continued safety and an extended service life from your tiedown assembly, please read and adhere
strictly to the following information:
These recommendations apply, in the main, to the use of webbing ratchet tiedown assemblies in road trans-
port and whilst some of the more general recommendations apply throughout the field of use of such prod-
ucts, it is important to realise that in some applications different requirements may apply.
• Ensure that sufficient tiedowns are used and that they are in good condition and strong enough to
secure the load.
• Where anti-chafing sleeves are supplied, ensure these are placed where edges or corners of the load
come in contact with the webbing.
• Do not increase the tension on the webbing by the use of levers or bars.
• Do not allow modifications or repairs to be carried out by anybody other than a certified manufacturer.
• Make use of anchorage points which are at least equal in strength to the webbing.
• Ensure that the sum of the lashing capacity of the total tiedowns used is at least equivalent to the mass
of the load and that the vehicle has at least one tiedown every 1.5 metres along the length of the load.
NOTE: Complex loads are likely to require additional tiedowns.
• Ensure the vehicle’s load space and the condition of it’s load platform are suitable and adequate for the
type and size of the load.
• Always ensure that the front of the load is abutted against the headboard of the vehicle or some other
fixed restraint, taking care not to overload any of the axles.
Repairs.
To ensure your tiedown assembly maintains it’s ultimate strength, do not allow repairs to be carried out by
non-certified manufacturers.
Repairs will only be undertaken where it is considered that following such repairs, the tiedown
assembly is deemed to provide continued safety.
Stopak brand dunnage bage have been tried and tested worldwide.
The standard 4 ply bag carried by Cookes ensures cargo remains
undamaged during transit and can be re-used numerous times.
INDEX
Confined Spaces Equipment......................................................................................... 122
Fall Arrest Devices ....................................................................................................... 121
Harnessed Overalls ....................................................................................................... 120
Harnesses ...................................................................................................................... 120
Horizontal Safety Lines ................................................................................................ 123
Karabiners..................................................................................................................... 121
Lanyards & Polestraps .................................................................................................. 121
Restraint Belts .............................................................................................................. 120
Vertical Rope Grabs ...................................................................................................... 123
Vertical Safety Lines..................................................................................................... 123
Lightweight single
point fall arrest harness
designed for general Unique Fraseon harness
fall protection. overall offers the wearer
Stainless steel buckles both overalls and a fall
offer ease of arrest harness in one easy to
connection and fit package. This harness
adjustment, while the comes with a waist belt
mesh back panel gives complete with D rings, and
unrestricted airflow for is fully detachable for laun-
increased wearer dering. Simply step into the
comfort. overalls for fast, easy fitting.
Lightweight single point harness Lightweight full body harness General purpose fall arrest
fitted with shoulder extension for fitted with shoulder D rings for harness fitted with rear fall arrest
ease of attachment. This general ease of retrieval in confined dorsal D ring and a waist belt
purpose harness has front attach- spaces. This harness is designed complete with side D rings. This
ment points suitable for restraint for use in confined space entry harness is suitable for heavy duty
and rescue purposes. and general fall protection. working applications.
RESTRAINT BELTS
Product Code: 09475200 Product Code: 09475601
Model: 2000 Model: 2601
Ergo padded back restaint Ergo linesman belt
belt c/w side D rings for c/w fully padded back
work positioning. The support and padded
specially selected foam drop down buttock
back support offers the strap. This belt offers
wearer greater comfort support and flexibility
and support. to it’s wearer.
Twin Lanyard
Product Code: 09440022
KARABINERS.
Confined space spreader bar designed for use with the Spanset 1200
series harness. Supplied complete with double action hooks for
added safety and wrist loop for easy recovery in tight situations.
INDEX
Standard Lengths :
6.0 metre (code 09996600)
9.0 metre (code 09996900)
Special lengths manufactured to order
O W IN
N O
U OR
FL
RA NGE
O
l Heavy Duty 75mm Polyester Webbing
l Approx 8,000 kgs Breaking Load
l Eye Protection each end.
• 10,000lb capacity
• Chromed for long life & good visibility
• Set includes high tensile bolts, nuts & safety clip
• Product Code: 09564691
Product Code Sheave Dia. Max Wire Rope Max. Pulling Weight
(mm) Dia. (mm) Load (tonne) (kg)
02007125 125 11 8.0 3.0
SNIG CHAINS
Product WLL Body Dia. Pin Dia. Inside Inside Bow Width Approx
Code (ton) D (mm) d (mm) Width Length 2r (mm) Weight
a (mm) C (mm) (kg)
02325013 1.50 11.0 12 18.5 43.0 29 0.21
02325016 2.00 13.5 16 22.0 51.0 32 0.37
02325019 3.25 16.0 19 27.0 64.0 43 0.65
02325022 4.75 19.0 22 31.0 76.0 51 1.06
02325026 6.50 22.0 25 36.0 83.0 58 1.56
• Manufactured From Heavy Duty Webbing Sewn Double Ply Specifically For Recovery of Heavy
Vehicles Such as Trucks, Buses etc.
• Reduced Eyes With Protective Cover Provide Longer Life
• The Webbing Elongates During Use Making The Product Safer Than Wire Rope or Chain Slings
• Standard Length 6 metres. Special Lengths Manufactured to Order
B. Economy Model:
Minimum Breaking Load 4,400 kgs.
Product Code Colour
09996025 White
Line Pull (kg) Line Speed Amp Line Speed Amp Line Pull (kg): 2,722 4,082
(mpm) (12/24V) (mpm) (12/24V) Motor (hp/W): 4.8/3,580 4.6/3,437
0 (No load): 14.6 40/24 13.4 40/24 Wire rope (m): 24.4 38.1
907: 7 170/102 4.6 120/72
1,814: 4 350/210 3.4 200/120 Gear train: 3 stage planetary
2,722: 3.1 440/264 2.7 260/156 Gear Ratio: 156:1
3,629: 2.3 320/192
4,082: 2.0 350/210
SPECIALTY PRODUCTS
INDEX
Product Code:
09995000
BULK WEBBING
TESTING SERVICES
INDEX
Recently the Courts have imposed heavy fines on firms who have
used unsafe equipment resulting in injury or death!
Whangarei Ashburton
Lower Port Road 120 Moore Street
55 tonne test bed
Timaru
Auckland 14 Bank Street
6-10 Greenmount Drive
East Tamaki
100 tonne test bed Dunedin
2A Orari Street
Tauranga 20 tonne test bed
1 Marsh Street
20 tonne test bed Invercargill
137 Clyde Street
Rotorua 20 tonne test bed
Marguerita Street
40 tonne test bed
Napier
182A Hyderabad Road
10 tonne test bed
New Plymouth
75 Corbett Road
37 tonne test bed
Wellington
2 Udy Street, Petone
20 tonne test bed
Nelson
8 Akersten Street
20 tonne test bed
Christchurch
124C Waterloo Road
50 tonne test bed
t!
e you righ
se
well
V
Vehicle Tow Straps ........................... 129
Vertical Rope Grabs .......................... 123
Vertical Safety Lines ........................ 123
W
Webbing - Bulk ................................. 133
Webbing Tiedowns & End Fittings ........
....................................... 109, 115
Web Slings .......................................... 39
Weissenfels Chain & Fittings ........76-80
Winches ................................. 59-60, 130
Wire Rope
Cutters ........................................... 10
Grips
Commercial Galvanised .......... 12
Commercial Stainless Steel ..... 13
Fist ........................................... 15
Generally to DIN 1142 ............ 13
Generally to FF-C-450 ............ 14
Instructions For Use ................ 11
Spelter Sockets .............................. 18
Swage Tool ................................... 10
Thimbles
Commercial Galvanised .......... 16
Commercial Stainless Steel ..... 16
Generally to BS 464 ................ 17
Thimbles - Solid
Generally to DIN 3091 ............ 17
Wire Rope Pull-lift Hoist .................... 58
Y
Yoke Chain & Fittings ................... 81-84