Professional Documents
Culture Documents
H21
[ Version 1.1 ]
WARNING
This service information is designed for experienced repair technicians only and is not intended for use by the general public.
It does not contain warnings or cautions to advise non-technical individuals of potential dangers in attempting to service a product.
Products powered by electricity should be serviced or repaired only by experienced professional technicians. Any attempt to service
or repair the product or products dealt within this service information by anyone else could result in serious injury or death.
WARNING: Denotes a potential hazard that could result in serious injury or death.
CAUTION: Denotes hazards that could result in minor injury or damage to the machine.
This section also explains the Warnings and Cautions used in the machine and/or this manual.
These symbols are used to alert operators to a specific operating procedure
that must not be performed.
These symbols are used to alert operators to a specific operating procedure
that must be emphasized in order to operate the machine safely.
WARNING
Power and Ground Connection Cautions
Ensure that the plug connection is free of dust. In a damp environment, a contaminated
connector can draw a significant amount of current that can generate heat and eventually
cause fire if left unattended over an extended period of time.
Always use the power cord provided with your machine. When an extension power cord is
required, always use a properly rated cord.
120 V/15 A or AC 220 - 240V/10 A
If you use a cord with an unspecified current rating, it may be underrated, and the machine,
or plug may emit smoke, orbecome hot to the touch.
Do not attempt to repair, pull, bend, chafe or otherwise damage the power cord. Do not
place a heavy object on the cord. A damaged cord can cause fire or electric shocks.
Never touch a power cord with wet hands. Danger of electric shock exists.
If the power cord is damaged, or insulated wires are exposed, contact the authorized
Panasonic dealer for a replacement. Using a damaged cord can cause fire or electric
shocks.
Stop operation immediately if your machine emits smoke, excessive heat, unusual noise, or
abnormal smell, or if water is spilt onto the machine. These conditions can cause fire.
Immediately switch Off and unplug the machine, and contact the authorized Panasonic
.
dealer.
Do not disconnect or reconnect the machine while the power switch is in the On position.
Disconnecting a live connector can cause arcing, consequently deforming the plug and
cause fire.
When disconnecting the machine, grasp the plug instead of the cord. Pulling on a cord
forcibly can damage it, and cause fire, or an electric shock.
When the machine is not used over an extended period of time, switch it Off and unplug it.
If an unused machine is left connected to a power source for a long period, degraded insulation
can cause electric shocks, current leakage or fire.
Be sure to switch Off, and unplug the machine before accessing the interior of the machine
for cleaning, maintenance or fault clearance. Access to a live machine's interior can cause
an electric shock.
6
Once a month, unplug the machine and check the power cord for the following. If you notice any unusual
condition, contact your authorized Panasonic
. dealer
The power cord is plugged firmly into the receptacle.
The plug is not excessively heated, rusted, or bent.
The plug and receptacle are free of dust.
The cord is not cracked or frayed.
Operating Safeguards
Do not touch areas where these caution labels are attached to, the surface may be very hot and may cause
severe burns.
Do not place any liquid container such as a vase, or coffee cup on the machine. Spilt water can cause fire or
shock hazard.
Do not place any metal parts such as staples or clips on the machine. If metal and flammable parts get into the
machine, they can short-circuit internal components, and cause fire or electric shocks.
If debris (metal or liquid) gets into the machine, switch Off and unplug the machine immediately.
Operating a debris-contaminated machine can cause fire or electric shock.
Do not try to alter the machine configuration or modify any parts. An unauthorized modification can cause
smoke or fire.
Consumable Safeguards
Never dispose of toner, toner cartridge, or a waste toner container into an open flame. Toner remaining in the
cartridge/bottle can cause an explosion, burns and/or injuries.
Keep button batteries/stamp out of the reach of children to prevent chocking or poisoning. If a button
battery/verification stamp is swallowed accidentally, get medical treatment immediately.
CAUTION
Installation and Relocation Cautions
Do not place the machine near heaters or volatile, flammable, or combustible materials such as curtains that
may catch fire.
Do not place the machine in a hot, humid, dusty, or poorly ventilated environment. Prolonged exposure to
these adverse conditions can cause fire or electric shocks.
Place the machine on a level and sturdy surface that can withstand the weight of the machine.
Refer to the Specifications section for the weight of the machine.
If tilted, the machine may tip-over and cause injuries.
When relocating the machine, remove the toner and/or developer, and pack the machine
e with proper
packing materials for shipping.
When moving the machine, be sure to unplug the power cord from the outlet. If the machine is moved with the
power cord attached, it can cause damage to the cord which could result in fire or electric shock.
7
CAUTION
Operating Safeguards
Do not place a magnet near the safety switch of the machine. A magnet can activate the
machine accidentally, resulting in injuries.
Do not use a highly flammable spray, or solvent near the machine. It can cause fire.
When copying a thick document, do not use excessive force to press it against the scanning
glass. The glass may break and cause injuries.
Never touch a labelled area found on, or near the heat roller. You can get burnt. If a sheet of
paper is wrapped around the heat roller, do not try to remove it yourself to avoid injuries or
burns. Switch Off the machine immediately, and wait until it cools down.
Do not use conductive paper, e.g. folding paper, carbon paper and coated paper. When a
paper jam occurs, they can cause a short circuit and fire.
Do not place any heavy object on the machine. An off-balance machine can tip-over, or the
heavy object can fall, causing damage and/or injuries.
Keep the room ventilated when using the machine for an extended period of time to minimize
the ozone density in the air.
When copying with the document cover open, do not look directly at the exposure lamp.
Direct eye exposure can cause eye fatigue or eye injury.
Pull the paper trays out slowly to prevent injuries.
When removing jammed paper, make sure that no pieces of torn paper are left in the machine.
A piece of paper remaining in the machine can cause fire. If a sheet of paper is wrapped
around the heat roller, or when clearing a jammed paper that is difficult or impossible to see,
do not try to remove it by yourself. Doing so can cause injuries or burns. Switch Off the
machine immediately, and wait until it cools down.
Consumable Safeguards
Never heat the drum cartridge, or scratch its surface. A heated, or scratched drum can be
hazardous to your health.
Do not mix new and old batteries together, as they can burst or leak, causing a fire or
injuries. Be sure to use the specified type of batteries
. only.
Ensure that batteries are installed with correct polarity. Incorrectly installed batteries can
burst or leak, resulting in spillage or injuries.
Others
When clearing a paper jam or other fault, follow the appropriate procedure given in this manual.
The machine has a built-in circuit for protection against lightning-induced surge current. If lightning
strikes in your neighborhood, maintain an ample distance from the machine, and do not touch it
until the lightning stops.
If you notice flickering, distorted images, or noises on your audio-visual units, your machine may
be causing radio interference. Switch it Off, and if the interference disappears, the machine is the
cause of the radio interference. Perform the following procedure until the interference is corrected.
Move the machine, and theTV and/or radio away from each other.
Reposition or reorient the machine, and theTV and/or radio.
Unplug the machine, TV and/or radio, and replug them into outlets operating on different circuits.
Reorient the TV and/or radio antennas, and cables until the interference stops. For an outdoor
antenna, ask your local electrician for support.
Use a coaxial cable antenna.
8
9
10
11
Table of Contents
12
Table of Contents
Exploded View & Parts List of 2-Bin Exploded View & Parts List of
Finisher (DA-FS600), 2-Bin Saddle-Stitch 2-Bin Finisher (DA-FS330) .................. 544
Finisher (DA-FS605) ............................ 423 8.1. Finisher Mounting Kit ........................... 544
6.1. Assembly Location Diagram .................423 8.2. Covers .................................................. 546
6.2. Attachment Parts ..................................426 8.3. Main Body ............................................ 548
6.3. External Covers, Panels, etc. ...............428 8.4. Transport Section 1 .............................. 550
6.4. Finisher Main Body ..............................432 8.5. Transport Section 2 .............................. 552
6.5. Harness Main Body Assembly..............436 8.6. Elevate Section .................................... 554
6.6. Tray Frame Assembly...........................438 8.7. Finisher Driver PCB Assembly ............. 556
6.7. Tray Drive Assembly.............................440
6.8. Feeder Drive Assembly ........................442 Exploded View & Parts List of 1-Bin
6.9. Feeder Assembly .................................444 Saddle-Stitch Finisher (DA-FS355A).. 559
6.10. Center Feeder Assembly ......................448 9.1. Assembly Location Diagram ................ 559
6.11. Buffer Upper Guide Assembly ..............450 9.2. Mounting Hardware .............................. 560
6.12. Inlet Feeder Assembly ..........................452 9.3. External Covers, Panels, etc. ............... 562
6.15. Stapler Tray Assembly..........................458 9.6. Stack Motor Driver Assembly ............... 572
6.17. Saddle Assembly 9.8. Bundle Support Cover Assembly ......... 576
(2-Bin Saddle-Stitch Finisher)...............464 9.9. Dispose Assembly................................ 578
6.18. Saddle Guide Assembly 9.10. Paper Feeder Assembly....................... 582
(2-Bin Saddle-Stitch Finisher)...............476 9.11. Fold Assembly...................................... 586
6.19. Stapler Assembly 9.12. Staple Assembly .................................. 592
(2-Bin Saddle-Stitch Finisher)...............478
9.13. DC Controller PCB Assembly .............. 596
6.20. Pass Lower Guide Assembly
(2-Bin Saddle-Stitch Finisher)...............480 9.14. List of Connectors ................................ 598
6.21. Inner Side Plate Assembly 9.15. List of Electric Parts ............................. 604
(2-Bin Saddle-Stitch Finisher)...............482
6.22. Saddle Delivery Assembly Exploded View & Parts List of
(2-Bin Saddle-Stitch Finisher)...............484 Punch Unit (DA-SP41) ......................... 609
6.23. Motor Mount Assembly 10.1. Assembly Location Diagram ................ 609
(2-Bin Saddle-Stitch Finisher)...............486 10.2. Puncher Assembly ............................... 610
6.24. Finisher Controller PCB Assembly .......488 10.3. Puncher Total Assembly ...................... 612
6.25. Saddle Controller PCB Assembly 10.4. List of Connectors ................................ 614
(2-Bin Saddle-Stitch Unit) .....................490
10.5. List of Electric Parts ............................. 616
6.26. List of Connectors.................................492
10.6. List of Standard Fasteners ................... 618
Exploded View & Parts List of Alphanumerical Parts List .................. 626
Punch Unit (DA-SP31) ......................... 523
7.1. Assembly Location Diagram .................523
7.2. Attachment Parts ..................................524
7.3. Punch Main Body..................................526
7.4. Punch Slide Assembly ..........................530
7.5. Punch Driver PCB Assembly ................532
7.6. List Of Connectors ................................534
7.7. List of Standard Fasteners....................536
13
DP-8060/8045/8035
1 Specifications Table
1.1. Copy Function
Description
Items Remarks
DP-8060 DP-8045 DP-8035
Basic Specifications
1 Type Semi Console
2 Platen Fixed
3 Original Position
Platen Left / Rear / Face Down
i-ADF Left / Center / Face Up
4 Recording Paper Path Center
5 Drum Organic Photo Conductor (OPC)
6 Copy Process Laser indirect Electrostatic
7 Developing Process Dry Dual Component
8 Toner Recycle No
9 Fusing System Heat Roller type
Ledger (11 x 17 in) /
10 Max Original Size
A3 (297 x 420 mm)
11 Paper Size
LTR For PU (USA/Canada, etc.)
1st Paper Tray
A4 For EU
(1,550 Sheet Paper Tray)
A4 For Other Destinations
LDR, LGL, LTR, LTR-R, INV-R For PU (USA/Canada, etc.)
Paper Tray A3, A4, A4-R, A5-R, B4 (FLS) For EU
A3, A4, A4-R, B4, B5, B5-R For Other Destinations
LDR, LGL, LTR, LTR-R, INV-R For PU (USA/Canada, etc.)
Sheet Bypass A3, A4, A4-R, A5-R, B4 (FLS) For EU
A3, A4, A4-R, B4, B5, B5-R For Other Destinations
Sheet Bypass Envelope No
Less than Less than
12 Warm-up Time 75 °F (20 °C)
180 sec. 30 sec.
From Platen/ Letter/ A4
Portrait/ 1st Paper Tray.
Less than Less than Less than
13 First Copy Time The time period is after the
3.5 sec. 4.6 sec. 5.8 sec.
Start key is pressed, and
Paper is ejected.
14 Copy Speed
Ledger / A3 34 cpm 27 cpm 20 cpm
Legal / B4, FLS 39 cpm 31 cpm 23 cpm
Letter-R 49 cpm 37 cpm 28 cpm
A4-R 48 cpm 36 cpm 27 cpm
LTR / A4 60 cpm 45 cpm 35 cpm
15 Zoom
Enlargement Selected Original size / Copy size
Reduction Selected Original size / Copy size
Zoom 25 - 400% 1% Step
Ver. 1.1
14 DEC 2006
DP-8060/8045/8035
Description
Items Remarks
DP-8060 DP-8045 DP-8035
16 Maximum Tray Capacities Front loading universal Paper Tray
Paper Tray
1,550 sheets x 1
Capacity
550 sheets x 1
Auto Size Setting Yes (2nd Tray only) PU (USA/Canada, etc.)
Low Level Warning Empty only LTR : 20 lb (75 g/m2)
Sheet Bypass
Capacity 50 sheets Other Destinations
Auto Size Setting Yes A4 : 80 g/m2
Paper Capacity
2,150 sheets
(Std. Configuration)
Max. Paper Capacity 6,250 sheets
17 Acceptable Paper Weight
Paper Tray 16-24 lb / 60-90 g/m2
Sheet Bypass 14.6-34.6 lb / 55-130 g/m2
18 Inverting ADF (i-ADF)
Duplex Type Yes (Standard)
Original Set Face Up
Scanning Method Sheet Through
PU (USA/Canada, etc.)
85 sheets (LTR) LTR : 20 lb (75 g/m2)
Capacity (Original)
70 sheets (A4) Other Destinations
A4 : 80 g/m2
Available for single side
SADF Mode Yes
scanning only.
Free Stop Yes From 17 to 60 degrees.
19 Multi Copy Range 1-999 sets
20 Gradation
Text 256 (Halftone by error diffusion)
Text / Photo 256 scale
Photo 256 scale
21 Resolution 600 dpi Scanning and Printing.
22 Standard Sorting Memory
32 MB
Size
23 Standard Page Memory Size 50 MB For Printing.
24 Exit Tray Capacity 250 sheets
25 Color No
26 Dimensions
29.8 x 23.6 x 35.4 in
(L x W x H) H: Up to i-ADF.
(757 x 600 x 900 mm)
Ver. 1.1
15 DEC 2006
DP-8060/8045/8035
Description
Items Remarks
DP-8060 DP-8045 DP-8035
27 Occupancy Area
29.8 x 46.7 in Includes Bypass Paper
(L x W)
(757 x 1,187 mm) Tray and exit Tray.
304 lb 298 lb
For PU (USA/Canada, etc.)
28 Weight (138.0 kg) (135.0 kg)
(Main Unit with i-ADF) For EU, and
138.0 kg 135.0 kg
Other Destinations
Options
1 Paper Feed System
550 sheets x1 (3rd)
Yes <DA-DS603>
Paper Feed Module
Paper Size Detection Manual (Control Panel)
PU (USA/Canada, etc.)
Low Level Paper Warning Empty only
LTR : 20 lb (75 g/m2)
Dimensions
28.7 x 23.6 x 11.4 in Other Destinations
(L x W x H)
(730 x 600 x 290 mm)
A4 : 80 g/m2
Weight 64 lb (29.0 kg)
550 sheets x 2 (3rd/4th)
Yes <DA-DS604>
Paper Feed Module
Paper Size Detection Manual (Control Panel)
PU (USA/Canada, etc.)
Low Level Paper Warning Empty only
LTR : 20 lb (75 g/m2)
Dimensions
28.7 x 23.6 x 11.4 in Other Destinations
(L x W x H)
(730 x 600 x 290 mm)
A4 : 80 g/m2
Weight 66 lb (30.0 kg)
Letter : 3,000 sheets <DA-MA301>
3000 sheets
Letter-R : 2,500 sheets
Paper Feed Module
Legal : 1,500 sheets LTR / LGL : 20 lb (75 g/m2)
Paper Size Detection Manual (Control Panel)
Low Level Paper Warning Empty only
Dimensions
17.5 x 11.6 x 19.9 in
(445 x 295 x 505 mm)
(L x W x H)
17.5 x 17.4 x 19.9 in With LTR-R / LGL Size
(445 x 442 x 505 mm) Adapter (DA-TK31)
33 lb (15.0 kg)
Weight With LTR-R / LGL Size
42 lb (19.0 kg)
Adapter (DA-TK31)
Max. Paper Capacity 6,250 sheets
2 1-Bin Saddle-Stitch Finisher - Yes DA-FS355A
3 2-Bin Finisher - - Yes DA-FS330
4 2-Bin Finisher Yes - DA-FS600
5 2-Bin Saddle-Stitch Finisher Yes - DA-FS605
6 Counter
Key Counter Capability Yes
Supplied as service part.
7 Dehumidifier Yes
Part Number: DZTQ000041
Ver. 1.1
16 DEC 2006
DP-8060/8045/8035
Description
Items Remarks
DP-8060 DP-8045 DP-8035
8 Electronic Sorting Board Standard (32 MB) CODEC + 32 MB memory
Optional Image Memory 1
Yes
(16 MB)
Optional Image Memory 2 Only one of three available
Yes
(64 MB) types can be installed.
Optional Image Memory 3
Yes
(128 MB)
Features
1 Automatic Features
Auto Magnification Selection Yes
Auto Paper Selection Yes
Auto Density Control Yes
Auto Paper Tray Selection Yes
Reservation while Power
Auto Start Yes
On Initializing
Energy Saver Mode
Standby Mode Yes
Energy Saver Mode Yes
Turns Off the Heater
Sleep Mode Yes (Approx. 20W) Power.
NW Function available
For USA/Canada,
Yes (Approx. 4W) With Finisher Power Supply
NW Function not available
Shutdown Mode
For Other Destinations
Yes (Approx. 5W) With Finisher Power Supply
NW Function not available
Requires the Fax
Remote Diagnostic Yes Communication Board
(DA-FG600) option.
Machine Stops while Out of
Yes Copier function
Toner
2 Additional Features
Low Level Paper Warning Empty only
Photo Mode Yes 256-step (Gray Scale)
Manually overridden when
Original Detection Release Yes using the Original Size
keys.
Edit / Effects
Book Mode Yes
Edge Mode Yes
Margin Mode Yes
X-Y Zoom Yes 25 - 400%
Available only when using
Page Numbering Yes
the ADF.
Inverse Mode (Negative /
Yes
Positive)
Ver. 1.1
17 DEC 2006
DP-8060/8045/8035
Description
Items Remarks
DP-8060 DP-8045 DP-8035
Centering Mode Yes
Mirror Mode No
Others (Inverting ADF &
ADU)
LDR → LTR x 2
2-Page Copy Mode Yes
(A3 → A4 x 2, B4 → B5 x 2)
2 in 1 Yes
4 in 1 Yes
6 in 1 Yes
8 in 1 Yes
Copy from 4 single-sided
Booklet Mode Yes pages to 1 booklet mode
sheet.
Duplex Copy
1→2 Yes
2→1 Yes
2→2 Yes
Book→2 Yes
Book Format Yes
Facing Pages Yes
Image Rotation (90 degrees) Yes
Electronic Sorting Yes
Rotation Sorting Yes
Insertion Job
Cover Mode Yes
Page Insertion Mode Yes
OHP Interleave Mode Yes Non-copy / Copy
Presentation Mode Yes
Department Counter Yes 300 Departments
Security Enhancement (CC) Yes (OP) Default Password: 00000000
i-ADF
LDR and LTR, LGL and
Multi Size Feed Yes LTR-R, A3 and A4, B4 and
B5, A4-R and A5
SADF Mode Yes
Original Counter No
Job Memory Yes (5)
Job Time Display No
Concurrent Copy Yes (12) HDD required
Tandem Copy Mode Yes HDD required
Remote Copy Mode Yes HDD required
Scan Once Print Many Mode Yes
Job Complete Notice Yes
Trial Copy Mode Yes
Weekly Timer Yes
User Mode Yes
Interrupt Yes
Ver. 1.1
18 DEC 2006
DP-8060/8045/8035
Description
Items Remarks
DP-8060 DP-8045 DP-8035
Electronic Counter Yes
Digital Sky Shot Mode Yes
Check / Slip Mode Yes
3 Control Panel
Display Wide Touch Panel LCD
GREEN : Scanning /
Status Lamp Yes Printing
RED : Alarm / Warning
Key
Original Size Yes
Copy Size Yes
Keypad Yes
Clear Yes
Stop Yes
Start Yes
Energy Saver Yes
Function Yes
Interrupt Yes
Reset Yes
One-Touch Key No
Copier / Printer / NW
Mode Change Yes Scanner / Fax, and Internet
Fax Mode change.
LCD Main Indication
English (American) For PU (USA/Canada, etc.)
Message Language
(Default) For EU, and Other
Specified Language
Destinations
Original Size / Image Yes
Indication (with Image)
Paper Size / Image Yes
Indication (with Image)
Paper Tray Selection Yes
Selected Paper Tray
Yes
Status
Original Mode Selection Yes Text / Text-Photo / Photo
Copy Density Selection Yes
Setting Confirmation Yes
Zoom Magnification Yes
Function Classification Yes
Number of Copies Yes
SADF / Multi Size Feed
Yes
Mode
Error Code Yes
Finishing Yes
Warning Indicators Yes
Add Toner Yes
Ver. 1.1
19 DEC 2006
DP-8060/8045/8035
Description
Items Remarks
DP-8060 DP-8045 DP-8035
Toner Waste Container
Yes
Full
Add Paper (No Paper) Yes
Add Paper
No
(Under 50 Sheets)
Paper Jam Indication Yes
Paper Jam Location Yes
Service Alert Call Yes
User Error Yes
Machine Error Yes
History of Jam Errors Yes
4 Main Unit
Total Counter Yes (Standard) Mechanical Counter
Max. Weight of Documents
11 lb (5 kg)
on the Platen Glass
ADF with Document Guide Yes
Clip Pocket Yes
Operating Instructions
Yes
Pocket
Warning / Caution Label Specified Language
5 Optical System
Original Detection Method Reflective Photo Sensor Type
Scanning Method 600 dpi CCD
Supplied as a Service Part
Dehumidifier Yes
Part Number: DZTQ000041
Mechanical Multi Copy
No
Mode
6 Process System
Separate OPC Unit, and
Type
Developer Unit Type
38K 33K For PU (USA/Canada, etc.)
Toner
37K 33K For EU / Other Destinations
Developer Life 240K
Drum Life 360K
Toner Waste Container 240K
Supplied as a Service Part
Dehumidifier Yes
Part Number: DZTQ000041
Manually adds toner to the
Manual Add Toner Yes developer
(up to TDC threshold)
Efficiency
1 Productivity
Warm-Up Time from Less than Less than
68 °F (20 °C)
Standby 180 sec. 30 sec.
ADF Productivity (LTR / A4)
Inverting ADF 100% Throughput
Ver. 1.1
20 DEC 2006
DP-8060/8045/8035
Description
Items Remarks
DP-8060 DP-8045 DP-8035
ADU Copy Productivity When ejecting to Outer
(LTR / A4) Tray
Transport Method Stackless
1→2
1 copy 45%
A4 / Letter
5 copies 75%
Throughput
10 copies 90%
PM Cycle
1 PM Cycle
Major PM 240K 120K 120K
Minor PM (Cleaning) 120K - -
Packing Configuration
1 Packing Dimension
35.8 x 28.5 x 42.9 in
(L x W x H)
(910 x 725 x 1090 mm)
348.3 lb
For PU (USA/Canada, etc.)
(158 kg)
2 Packing Weight
For EU, and
155 kg
Other Destinations
3 Accessories
OPC Unit Yes
Developer No
Toner No
Toner Waste Container Yes
Option For PU (USA/Canada, etc.)
Outer Tray For EU, and
Yes
Other Destinations
Operating Instructions Yes
Power Supply
99 - 138 VAC, 47 - 63 Hz
120 VAC Power Supply
Single phase
1 Power Requirement
180 - 264 VAC, 47 - 63 Hz
220 VAC Power Supply
Single phase
2 Power Consumption Less than 1.45 kW
Ambient Conditions
1 Temperature 50 - 80 °F (10 - 30 °C)
2 Relative Humidity 30 - 80%
UL60950 / CSA C22.2 No.60950 For PU (USA/Canada, etc.)
3 Safety For EU, and
UL60950-1 / CSA C22.2 No.60950-1
Other Destinations
4 Energy Saver Energy Star Compliant
Class A computing device in FCC Rules
5 EMI For PU (USA/Canada, etc.)
Part 15
EN55022 / EN55024
6 EMC For EU
EN61000-3-2,-3
Ver. 1.1
21 DEC 2006
DP-8060/8045/8035
1.2. Fax, Printer, Network Scanner, and Internet Fax Functions
1.2.1. Fax Function
Description
Items Remarks
DP-8060 DP-8045 DP-8035
Main Specifications
1 Compatibility G3 ITU-T Std. & Non-Std. (PCC)
2 PSTN Line Port Yes 1-Line Only
3 Leased Line Port No
4 V.24 Line Port No
5 Modem Speed 33.6 - 2.4 kbps
6 Coding Scheme JBIG / MMR / MR / MH
7 ECM Yes Conforms to ITU-T
8 Short Protocol Yes (B, D)
ITU-T Image No. 1
9 Transmission Speed Approx. 3 sec.
(A4, Std. Resolution)
Transmission
Std. 8 x 3.85
Fine 8 x 7.7
S-Fine 8 x 15.4
16 x 15.4
600dpi 600 x 600 dpi
10 Communication Resolution
(pels/mm x lines/mm)
Reception
Std. 8 x 3.85
Fine 8 x 7.7
S-Fine 8 x 15.4
16 x 15.4
600dpi 600 x 600 dpi
Scanner Mechanism
1 Scanning Device CCD (i-ADF / Platen)
2 Scanning Speed
Resolution Vertical Horizontal
Std: 8 x 3.85
1.0 sec. 0.7 sec.
(pels/mm x lines/mm)
Fine: 8 x 7.7 A4, Scanned in Vertical, or
1.0 sec. 0.7 sec.
(pels/mm x lines/mm) Horizontal Direction
S-Fine: 16 x 15.4
2.0 sec. 1.4 sec.
(pels/mm x lines/mm)
600dpi: 600 x 600 2.0 sec. 1.4 sec.
Std. 8 x 3.85
Fine 8 x 7.7
3 Scanning Resolution
S-Fine 8 x 15.4
(pel/mm x lines/mm)
16 x 15.4
600dpi 600 x 600 dpi
4 Document Size (Max.) ADF: Ledger / A3
5 Effective Scanning Width LDR (11.5 in) / A3 (292 mm)
6 A3 size TX / RX Yes Conforms to ITU-T A3
A3 to B4 / A3 to A4 / B4 to A4
7 Reduction XMT Yes Ledger to Legal / Ledger to
Letter / Legal to Letter
Ver. 1.1
22 DEC 2006
DP-8060/8045/8035
Description
Items Remarks
DP-8060 DP-8045 DP-8035
8 ADF/i-ADF Yes Face-Up, feed from top page
9 Collation Stack Yes Face Down
Printer Mechanism
1 Recording Method Laser Indirect Electrostatic
60 ppm 45 ppm 35 ppm
2 Recording Speed (Letter/A4 (Letter/A4 (Letter/A4
Horizontal) Horizontal) Horizontal)
3 Recording Resolution Fax 600 x 600 dpi
Invoice : Not supported.
Ledger size is transmitted as
A3 size for N. American
Ledger / Legal / Letter /
4 Recording Paper Size models. If A3 is received,
A3 / B4 / A4 / A5 / B5 / INV
approx. 1" of image on both
edges are not printed on
Ledger size paper.
5 Effective Printing Width 11.4 in (289 mm) Conforms to ITU-T A3
6 Recording Paper Capacity 2,150 sheets Optional max. 6,250 sheets
7 Collation Stack Yes Face Down
8 Consumables Toner Bottle, Developer, and Staples
Fax Memory
Flash ROM, ITU-T Image No.1
1 Standard Memory 3 MB (180 pages)
(A4, Std. Resolution)
4 MB Expansion Flash Memory
2 Optional Memory
8 MB Card
Dual Operation
1 Multi Task Operation Yes
2 Direct XMT Reserve Yes
3 Memory XMT Reserve Yes
4 Number of Memory Job
Yes (Max. 50 files)
Files
Dialing/Telephone Features
Plus an additional 800 stations
available to select from, when
1 Address Book Dialing 200 Stations
the optional Hard Disk Drive
(DA-HD60) is installed.
2 Full Number Dialing
Yes Max. 70 stations
(Buffered Dialing)
3 Address Book Directory
Yes
Search Dialing
200 Address Book + 70 Full
4 Total Auto Dialers 270 Stations
Number Dialing
5 Program Dials 12
6 Max. Tel Number Digits 36
Ver. 1.1
23 DEC 2006
DP-8060/8045/8035
Description
Items Remarks
DP-8060 DP-8045 DP-8035
7 Max. Station Name
15
Characters
8 Direct Dialing
Yes Voice mode
(Monitor Dialing)
9 Automatic Redialing Yes
10 Manual Redialing Yes
11 Line Monitor Speaker Yes Available for Line-1 only
12 Chain Dialing (Hybrid Dial) Yes In Monitor Dialing mode only
13 Pulse / Tone Dialing Yes 10 pps / DTMF
14 Pulse to Tone Change Yes
15 Flash Key Yes
16 Handset No
Transmission Features
1 Direct Transmission Yes
2 Memory Transmission Yes Page Retransmission
3 Quick Memory
Yes
Transmission
4 Multi-Station Transmission
Yes Max. 270 Stations
(Sequential Broadcasting)
5 Direct Deferred
No ADF Deferred Transmission
Transmission
6 Deferred Transmission Yes Max. 50 Timers
7 Deferred Multi-Station
Yes
Transmission
8 Priority Direct
Yes Priority ADF Transmission
Transmission
9 Priority Memory
No
Transmission
10 Batch Transmission Yes Real Time (up to 5 Files)
11 90 Degree Rotation
Yes
Transmission
12 Cover Sheet Yes
13 Confidential Mail Box No
14 Multi-Copy Transmission No
FAX : Back-up with Flash
Memory.
15 Memory Back-Up Yes
Copy / Printer : No Back-up
with SD-RAM
16 Duplex Scanning Yes With Inverting ADF (i-ADF)
Reception Features
1 Substitute Reception Yes
LTR/A4/LGL: 70 - 100%
2 Fixed Reduction Yes (in 1% Steps),
Top & Left Alignment
LTR/A4/LGL: 70 - 100%
3 Auto Reduction Yes (in 1% Steps),
Top & Left Alignment
Ver. 1.1
24 DEC 2006
DP-8060/8045/8035
Description
Items Remarks
DP-8060 DP-8045 DP-8035
Page End Approx. 0.51 in
4 Overlap Printing Yes
(13 mm)
5 Receive to Memory Yes
6 Distinctive Ring Detector
No
(DRD)
7 90 Degree Rotation
Yes
Reception
8 Duplex Printing Yes
Polling
1 Polling Yes
2 Turnaround Polling No
3 Multi-Station Polling Yes Max. 270 Stations
4 Deferred Polling Yes Max. 50 Timers
5 Deferred Multi-Station
Yes Max. 50 Timers / 270 Stations
Polling
6 Direct Polling Tx No
7 Memory Polling Tx Yes 1 File
8 Preset Polling Password Yes
9 Temporary Polling
Yes
Password
10 Continuous Polling Yes
Convenience
1 Panel Display Wide Touch Panel Display
2 Voice Contact No
3 Edit File Mode Yes With View Mode
4 Incomplete File Save Yes With View Mode
5 Automatic Cover Sheet Yes
Certainty
1 Verification Stamp Yes
2 Header / Total Page Print Yes
200 Transactions / with View
3 Transaction Journal Yes
Mode
4 Comm. Journal Yes With Image Data
5 Last Ind. XMT Journal Yes
List Printouts
1 One-Touch List -
2 ABBR. No. List -
3 Program List Yes
4 Address Book Search List Yes Auto Dialer List
5 Fax Parameter List Yes
6 File List Yes With View Mode
7 Ind. XMT Journal Yes
8 Journal Yes Last 200 Transactions
Ver. 1.1
25 DEC 2006
DP-8060/8045/8035
Description
Items Remarks
DP-8060 DP-8045 DP-8035
Identifications
1 Logo Yes 25 Characters
2 Multiple Logo No
3 Character ID Yes 16 Characters
4 Numeric ID Yes 20 Digits
Special Communications
1 Password XMT / RCV Yes
2 Selective Reception Yes TSI Check
3 Relay XMT Request No
4 Relay XMT Center No
5 Confidential XMT / Polling No
6 Confidential Center No
7 Mailbox XMT / Polling Yes
8 Mailbox Center No
9 File XMT No
Received File Transfer
10 Fax Forward Yes
(Only with Internet Fax Option)
11 Sub-address XMT Yes T. Routing
12 Sub-address RCV Yes
13 OMR-XMT No
Standards
FCC Part 68: / Industry Canada
1 PSTN For USA and Canada only
No. CS-03: Issue 9
Others
1 Fax Access Code Yes
2 PIN Code Access Yes For USA and Canada only
3 Department Code Yes 300 Departmental Codes
4 Power Saver Mode Yes
5 Self Diagnostic Function Yes
6 Remote Diagnostic
Yes
Function
7 Check & Call Function Yes
8 V.24 / Encryption Interface No
Ver. 1.1
26 DEC 2006
DP-8060/8045/8035
1.2.2. Printer Function
Description
Items Remarks
DP-8060 DP-8045 DP-8035
Interface
1 Centronics Parallel I/F Centronics Parallel Interface IEEE-1284 Compliant
2 LAN (Network) Ethernet 10Base-T/ 100Base-TX
3 USB Port No
4 IEEE-1394 No
Printer Function
Ledger, Legal, Letter, Invoice, A3, A4,
1 Printing Size
A4-R, A5, A5-R, B4
2 Bypass Yes
3 Stapling Yes
4 Printing Resolution (dpi) 600 x 600 Selectable, 600 dpi Printer
5 Interface Centronics Parallel Interface/Ethernet
Win 98 / Me / Win NT 4.0 /
6 OS
Win 2000 / XP / Windows Server 2003
7 GDI Yes
Requires Optional PCL6
8 PDL (PCL6) Yes
Emulation Kit
Requires Optional PS / PCL6
9 PDL (PS3) Yes
Emulation Kit
10 Duplex Printing Yes
11 Collation Stack Yes
12 Status Monitor (Local) No
13 Network Printing Yes
14 Network Status Monitor Yes
15 Smoothing Yes
16 Applicable PC IBM PC, AT or Compatible
17 Multi-Task Operation
Printing while Fax-XMT
Yes
from Memory
Printing while Fax-RCV into
Yes
Memory
Fax-XMT from Memory
Yes
while Printing
Fax-RCV into Memory while
Yes
Printing
18 Output to separate tray for
Yes
Printing, Fax, Copy
Requires Optional PCL6, or PS
19 Font Yes
/ PCL6 Emulation Kit
20 Security Print Requires Optional HDD Unit
Mailbox Yes Max. 100 Boxes
Secure Mailbox Yes Max. 50 File
Auto Pop-up on the PC Screen
(requires Job Status Utility -
21 Completion Notice Yes
installed with Panasonic-DMS
Software)
Ver. 1.1
27 DEC 2006
DP-8060/8045/8035
1.2.3. Network Scanner Function
Description
Items Remarks
DP-8060 DP-8045 DP-8035
Interface
1 Centronics Parallel I/F No IEEE-1284 Compliant
Ethernet 10Base-T/
2 LAN (Network)
100Base-TX
3 USB Port No
4 IEEE-1394 No Firewire
Network Scanning Function
1 Scanning Device CCD (i-ADF / Platen)
2 Halftone 256 Halftone Shades With Error Diffusion
3 Max. Document Size A3, Ledger
600 x 600
4 Scanning Resolution Selectable, 600 dpi Optical
300 x 300
(dpi) Scanner
150 x 150
Win 98 / Me / Win NT 4.0 /
5 OS
Win 2000 / XP / Windows Server 2003
6 2-Sided Scanning Yes With i-ADF.
7 File Format Mult-page TIFF / PDF
8 Protocol TCP/IP, Non-Std
Network Scanner Address Features
1 Network Registration 120
2 Touch Panel Registration 60 With Error Diffusion
Ver. 1.1
28 DEC 2006
DP-8060/8045/8035
1.2.4. Internet Fax Function
Description
Items Remarks
DP-8060 DP-8045 DP-8035
Main Specifications
1 Communication
TCP / IP SMTP / MIME
Protocols
2 Max. Modem Speed NA
3 Coding Scheme MH / MMR / JBIG
Selectable (PDF format can be used for
Scan-to-Email when sending to a PC.
However, since current Internet Fax
4 File Format Mult-page TIFF / PDF
standards do not support this file
format, it cannot be used for sending to
another Internet Fax machine)
5 Line Interface RJ-45 (Ethernet) Ethernet LAN
Scanner Mechanism
1 Max. Document Size Ledger, A3
2 Effective Scanning Width 11.4 in (289 mm)
Std 203 x 98 (8 x 3.85)
Fine 203 x 196 (8 x 7.7) LAN: 600 dpi, 16 x 15.4 Scanning
3 Scanning Resolution
S-Fine 203 x 391 (8 x 15.4) Resolution is available with
(pel/mm x lines/mm)
406 x 391 (16 x 15.4) Parameter setting
600dpi 600 x 600 dpi
Printer Mechanism
1 Printing Resolution 600 dpi
2 Effective Recording
11.4 in (289 mm)
Width
Transmission Features
Simultaneous operation of G3 Fax, and
1 Multi-Task Operation Yes
LAN is available
2 Memory Transmission Yes
3 Sequential Multi-Station
-
Transmission
Max. 270 Stations
4 Simultaneous Multi-
Yes (200 Address Book + 70 Full Number
Station Transmission
Dialing)
5 Sender Selection Yes
6 G3 / Email Mixed
Yes
Broadcasting
7 Deferred Transmission Yes
Received File Transfer, only with
8 Fax Forward Yes
Internet FAX Option
Inbound Routing, only with Internet
9 Sub-address RCV Yes
FAX Option
Ver. 1.1
29 DEC 2006
DP-8060/8045/8035
Description
Items Remarks
DP-8060 DP-8045 DP-8035
10 Mail Header
Email Header Print
Yes All or From / To / Subject only
Selection
Subject Line Random Entry
LAN Features
1 Internet Fax A3 Communication is available with
Yes
Communication Parameter setting
2 Internet Mail Reception Yes
3 Internet Fax Server
Features
Internet Fax Relay XMT Yes Internet Fax → Internet Fax → G3FAX
Email Relay MXT Yes PC → Internet Fax → G3FAX
Received Fax / Email
Yes Local print available
Forward
PC to FAX Transmission Yes Requires Panafax Desktop Software
Using Sub-Address
Inbound Routing Yes
Local print available
Address Book
Yes Via Email
Registration from PC
4 I-Fax Parameters
Yes
Registration via Email
5 Internet Delivery
Yes With MDN
Confirmation
6 Network Scanning Yes 600 dpi
7 Network Printing
LPR / LPD Yes 600 dpi
GDI Yes
Requires Optional PCL6 or PS
PDL Yes
Emulation Kit
8 DHCP Client Yes
9 LDAP Yes Lightweight Directory Access Protocol
10 TIFF Viewer Yes Selectable, PDMS / TIFF Viewer
Certainty
1 Comm. Journal Email from RCV side to Panasonic
Yes
(w / Image) Internet FAX's only
ID
1 Email Address Yes
Ver. 1.1
30 DEC 2006
DP-8060/8045/8035
1.3. System Combination
Ver. 1.1
31 DEC 2006
DP-8060/8045/8035
1.4. Options and Supplies List
1. Options
Option Name Option Number Remark
Printer Controller Module for PCL6-IPX/ For PU version only (USA/Canada, etc.)
DA-PC800
SPX Program Expansion Board (FRM8) is
Multi Page Description Language included with DA-PC800 and DA-MC800
DA-MC800
Controller Module for PS/PCL6-IPX/SPX options. The PCL Firmware is included on
the FRM8 board, therefore, firmware
DDS Unlock Module DA-UK10 update is not required.
Printer Controller Module for GDI-IPX/SPX DA-GC601 Except PU (USA/Canada, etc.)
Document Distribution System (DDS) DA-WR10
Network Scanner Module - Std. for DP-8060/8045/8035
Internet Fax / E-Mail Module - Std. for DP-8060/8045/8035
Fax Communication Board DA-FG600 G3 Fax Communication
Hard Disk Drive Unit DA-HD60 Except PU (USA/Canada, etc.)
Image Memory (16 MB) DA-SM16B
Image Memory (64 MB) DA-SM64B For Electronic Sorting
Image Memory (128 MB) DA-SM28B
Expansion Flash Memory Card, 4 MB UE-410047 Additional Page Memory for Fax
Expansion Flash Memory Card, 8 MB UE-410048 Communication Board (DA-FG600)
DD Server Software DA-WS20 For DD Server Function
Accounting Software DA-WA10 For Accounting Function
Data Security Kit DA-SC01 For Specified Destinations
Deluxe Stand DA1D351
For USA, and Canada only
Deluxe Stand (Short) DA-D352R
System Console 1 (Tray x 1) DA-DS603
System Console 2 (Tray x 2) DA-DS604
3000-Sheet Tray (LCT) DA-MA301 3,000-Sheet Large Capacity Tray
Letter-R / Legal Size Adapter
DA-TK31 For USA and Canada
for LCT (DA-MA301)
Exit Tray (Outer) DA-XT600 For PU (USA/Canada, etc.)
2-Bin Finisher DA-FS600
2-Bin Saddle-Stitch Finisher DA-FS605 For DP-8060/8045
Punch Unit for DA-FS600/605 DA-SP31
1-Bin Saddle-Stitch Finisher DA-FS355A
For DP-8045/8035
Punch Unit for DA-FS355A DA-SP41
2-Bin Finisher DA-FS330 For DP-8035
For PU (USA/Canada, etc.) : Std.
For PK, PT : Option
Optional Power Supply (LVPS) for Finisher DA-PW600 For PB and Other Destinations :
DP-8060/8045 : Std.
DP-8035 : Option
Key Counter Harness Kit PJEEF2750PU
Supplied as a Service Part
Dehumidifier Heater DZTQ000041
Note:
PCL6 is a Page Description Language of the Hewlett-Packard Company.
PS/PS3 is a Page Description Language of the Adobe Systems Company.
Ver. 1.1
32 DEC 2006
DP-8060/8045/8035
2. Supplies
Part Name Part Number Remarks
DQ-TU38R DP-8060 : 38K (Letter / 6%)
Toner DQ-TU37R DP-8060 : 37K (A4 / 6%)
DQ-TU33R DP-8045/8035 : 33K (LT A4 / 6%)
FQ-SS32 DA-FS330 : Staple Cartridge Refills (3)
DQ-SS35 DA-FS355/355A : Staple Cartridge Refills (3)
Staple Cartridge DA-FS605 (Saddle Stitch) : Staple Cartridge
FQ-SS50
Refills (3)
FQ-SS66 DA-FS605 / 600 : Staple Cartridge Refills (3)
OPC Drum DQ-H360R 360K
Developer DQ-Z240R 240K
Note:
The Part Number(s) may differ for other than PU (USA/Canada, etc.) destinations. Please ask your sales
company for details.
Ver. 1.1
33 DEC 2006
DP-8060/8045/8035
1. Timing
- Perform the preventive maintenance service in accordance with the chart of preventive maintenance
areas listed in the service manual.
2. Cleaning of Rollers
- Rollers should be cleaned with water and cloth.
- Use of IPA (Isopropyl alcohol) should be used sparingly.
Ver. 1.1
34 DEC 2006
DP-8060/8045/8035
5. Data Security Precautions during Maintenance, and Disposal
To secure highly-sensitive document data from unauthorized users during maintenance, or when
disposing of this equipment, follow the security measures described below.
a. Maintenance:
Make sure to remove the Flash Memory Card from the machine, if it was used for updating the
Firmware, etc.
2. Disposal:
a. Delete the customer’s data by initializing the Hard Disc Drive (overwriting, and deleting the data
area stored in the Hard Disc Drive).
b. Delete the customer’s data by initializing the System.
Important
No. Part Description Comments
Action
1 Memory Data Check 1. Print the RAM DATA for reference and as a pre-caution.
2. After completing the task(s), print and compare the RAM
DATA with the previously printed one.
2 Auto Document Check & 1. Clean all Rollers and Separation Rubber with a soft cloth
Feeder (ADF) Clean saturated with water.
Note:
For stubborn toner accumulation, wipe with a soft cloth
saturated with Isopropyl Alcohol first, then follow up with a
soft cloth saturated with water.
3 Scanner Unit Check & 1. Clean the Scanning Glass, or White Seal Guide with
Clean Isopropyl Alcohol when required.
4 Document Size Check & 1. Do not touch the surface of the Sensors with your hands.
Sensor Clean 2. Clean any dirt or fingerprints with a Dry Cotton Swab.
Note:
Do not use any type of Alcohol.
5 Transmitter Unit Check & 1. Remove any foreign obstacles.
Clean 2. Clean the Rollers with Isopropyl Alcohol when required.
6 Mirrors Check & 1. Do not touch the surface of the Mirrors with your hands.
Clean 2. Clean any dirt or fingerprints with a Dry Cotton Swab.
Note:
Do not use any type of Alcohol.
7 Inspection Items Check 1. Check the Harnesses.
2. Check the Connectors.
3. Check the Screws. If required, replace consumable parts.
8 Gears, Rollers Shafts Check & 1. Check, and grease the required Gears and Shafts.
Grease
9 Timing Belts Check & 1. Check the belts for looseness, or abrasion.
Clean 2. Adjust the Idle Pulley.
10 Fuser Unit Check & 1. Remove any foreign obstacles.
Clean Note:
Do not use any type of Alcohol.
Ver. 1.1
36 DEC 2006
DP-8060/8045/8035
2.3. Preventive Maintenance Points
8 7 6 12 13 3
24
23
9
1
10
17
11
19
26 25
5
20
2221
B
55 (14-16)
30 29 28
57
18
48 56
58
A 44
(31-43)
4
50 54
49 53
47 46 51
52
59 62
45 60
2 61
27 54
51
53
52
54
51
53
52
54
53 52 51
Note:
3 Except PU
35
36
39
33
40
38 34
31
37
32
41
42 43
DETAIL A
14
15
16
DETAIL B
Ver. 1.1
38 DEC 2006
DP-8060/8045/8035
2.4. Preventive Maintenance Check List
Cleaning Replacement/Adjustment
Ref.
No. Mechanical Parts Ref. No. Cycle Cycle
Method Procedure Counter
(Sheet) (Sheet)
Main Unit
1 Ozone Filter 1 4204 - - 240K
2 Ozone Filter 2 107, 4229 - - 240K Refer to
V-Ozone Filter 4 4226 - - 240K Sect 2.2.1.of F7-02
3
V-Ozone Filter 7 4228 - - 240K the Service Total Count
4 Ozone Filter 6 136 - - 240K Manual
5 Dust Filter 4218 - - 240K
i-ADF Unit
6 Pickup Roller 511 120K Water 1 240K
7 Paper Feed Roller 508 120K Water 1 240K
8 Separation Roller 610 120K Water 1 240K
Refer to
9 Registration Roller 1 817 120K Water 1 - F7-02
Sect 2.2.3.of
ADF PM
10 Registration Roller 2 818 120K Water 1 - the Service
Count
Manual
11 Transport Roller 816 120K Water 1 -
12 Inverting Roller 809 120K Water 1 -
13 Exit Roller 814 120K Water 1 -
Hopper Unit
14 Toner Bottle Holder 1402 480K Water 1 - Refer to
Sect 2.2.6.of F7-02
15 Toner Bottle Support 1407 480K Water 1 -
the Service Total Count
16 Lower Hopper Cover 1411 480K Water 1 - Manual
Developer Unit
- Developer - - - 240K *4 Refer to
Splash Prevention F7-02
17 1602 - - 720K Sect 2.2.7.of
Sheet Process
the Service
Unit Count
18 Duct Cover 1620 240K Water 1 - Manual
Drum Unit
19 OPC Drum 1811 - - 360K *4
20 Cleaning Blade 1847 - - 360K
21 Front Cleaning Felt 1849 - - 360K
22 Rear Cleaning Felt 1848 - - 360K
Corona Wire
120K
(DP-8045/8035)
23 1915 - - Refer to
Corona Wire F7-02
240K Sect 2.2.8.of
(DP-8060) OPC Drum
the Service
24 Corona Case 1906 240K Water 1 480K
Manual
Count
25 Corona Grid 1919 240K Water 1 480K
26 Cleaning Pad Assy 1957 - - 240K
Toner Waste
27 4108 - - 240K *4
Container
Density Sensor
28 1846 240K Dry Cloth -
(CDS PC Board)
Ver. 1.1
40 DEC 2006
DP-8060/8045/8035
Cleaning Replacement/Adjustment
Ref.
No. Mechanical Parts Ref. No. Cycle Cycle
Method Procedure Counter
(Sheet) (Sheet)
Sheet Bypass
55 Paper Feed Roller 4608 120K Water 1 240K Refer to
F7-03
1 Sect 2.2.14.
56 Feed Roller 4612 120K Water 240K Sheet
of the
Bypass
Service
57 Pickup Roller 4603, 4611 120K Water 1 240K Count
Manual
Paper Exit Transportation
58 Exit Roller 2 8120 120K Water 1 - Refer to
Sect 2.2.15.
F7-02
of the
59 Exit Roller 3 8312 120K Water 1 - Total Count
Service
Manual
3000-Sheet Large Capacity Tray
60 Paper Feed Roller 9111 120K Water 1 240K Refer to
Sect 2.2.19. F7-03
61 Feed Roller 9129 120K Water 1 240K
of the LCT Tray
Service Count
62 Pickup Roller 9107 120K Water 1 240K
Manual
Note:
1. Clean all Rollers and Separation Rubber with a soft cloth saturated with water.
For stubborn toner accumulation, wipe with a soft cloth saturated with Isopropyl Alcohol first, then
follow up with a soft cloth saturated with water.
2. The Maintenance Cycle is based on the Counter Information for each individual module.
To verify the counter information, print the Total Counter List using the Service Mode: F7 - Electronic
counter - 00 (List print).
3. Cleaning, Replacement and Adjustment Cycle (Sheet) are based on using Panasonic's recommended
standard paper and supplies. These cycles may vary with the kind of paper used and/or ambient
conditions.
4. The value is determined under the following test conditions. Four continuous prints per job using 6%
image coverage of LT/A4 size.
5. 240K, or 1 year whichever occurs first.
Ver. 1.1
42 DEC 2006
DP-8060/8045/8035
2.6. Updating the Firmware
The Quickest and Most Reliable Way of Updating the Firmware is to use the Network Firmware
Program Tool (FUP) using Ethernet LAN Port, and a Crossover Cable.
The network FUP Tool version must be 3.XX or higher, and it can be found on the CD included with PCL or
PS/PCL options.
Refer to the Firmware Update Operation Instructions, and Service Notes for Option Instalation
(8.1.) for the details.
2.6.1. Firmware Configuration
A. Hardware Configuration
This machine is controlled by three (3) CPUs which are located on the System Control (SC) PC
Board, the Panel Control (PNL) PC Board, and the Scanner Printer Control (SPC) PC Board.
SC PC Board Standard
Configuration
With PCL Option
Configuration
With PS Option
Configuration
PC
8 MB (4) (7)
Flash Memory Font Program
Card (b) (b)
4 MB 4 MB
4 MB or 8 MB
Slot 2
FRM8 PCB
8 MB
PNL PC Board
SPC PC Board
F-ROM
Scanner Control Program
CPU 512 KB Printer Control Program
Ver. 1.1
44 DEC 2006
DP-8060/8045/8035
2.6.2. Updating through a LAN Port (The Quickest and Most Easiest Method)
The firmware code can be easily updated when the main unit is connected to a LAN.
If the unit is not connected to a LAN, the Network Firmware Update Tool can be used by connecting to the
machine using a Crossover Cable.
Caution:
Before proceeding with the Firmware Update, clear all Fax or Internet Fax jobs first, or the Firmware will
not update properly. Follow the steps below to perform All Job Clear.
1. Press the "Function”, “Original Size (Ledger/A3)", and “3” keys simultaneously in that order to
enter the Service Mode.
2. “Input the password” to enter the Service Mode (default password is 00000000).
3. Press "9", and then “Start” keys to enter the F9 Service Mode (Unit Maintenance).
4. Select "00 FAX Service Mode".
5. Select “06 RAM Initialize“.
6. Select "09 All Job Clear", and then “Yes”.
After clearing the jobs, the machine reboots automatically, and returns to the standby mode.
Please refer to the following Operating Instructions to install the Network Firmware Update Tool.
The installation password is "workio".
Operating Instructions:
\xFirmware\Tools\NwFirmup\NwFirmup OI.pdf (Refer to the Network Firmware Update Tool OI on the
CD)
Setup:
\xFirmware\Tools\NwFirmup\Setup\Setup.exe
Note:
1. Manual mode must be used, when updating the designated version of the firmware, or changing
the type of the firmware.
Please refer to the Section 2.2, "Setting up the Network Firmware Update Tool, File Selection
Tab" of the Operating Instructions.
2. While updating the firmware code, the display may become garbled, however, it will return to
normal upon completion of the firmware update.
3. If the firmware update fails and the unit does not boot up, the Network Firmware Update Tool will
not be able to transfer the firmware code. If this occurs, please refer to the next section "Updating
through the Parallel Port" and use the Local Firmware Update Tool to recover the unit.
4. The suffix "_xx" for the Folder Name, or File Name may not exist depending on the destination
location.
5) After the Firmeware Update is completed, enter the F5 & F6 Parameters according to the lists printed
in step (3) above.
Ver. 1.1
46 DEC 2006
DP-8060/8045/8035
2.6.3. Updating the Firmware using a PC via the Parallel Port
1. Before starting, print the F5 & F6 Parameters (Copier) Lists.
2. Turn the Main Power Switch on the back of the unit (not the side of the unit) to the OFF (O) position.
3. Connect the machine to the PC with a Parallel Printer Cable.
4. Turn the Main Power Switch on the back of the unit to the ON (I) position.
5. Install the Panasonic Firmware Programming Wizard software into the PC.
(Refer to the Firmware Update Tool Operating Instructions)
6. Perform the Copy Service Mode F9-07-01 (Update from parallel port).
Now the machine is ready to accept programming firmware code from the PC.
7. Start the Panasonic Firmware Program using the Wizard.
8. The firmware is copied into the machine.
9. After the update is completed, the machine reboots itself and returns to standby.
10. Perform the Copy Service Mode F9-06-00 (Parameter initialize).
11. Turn the Main Power Switch on the back of the unit (not the side of the unit) to the OFF (O) position.
12. Disconnect the Parallel Printer Cable from the machine.
13. Turn the Main Power Switch on the back of the unit to the ON (I) position.
14. Reprogram the F5 & F6 Parameters (Copier) according to the lists printed in Step 1 above if the
settings are other than factory default.
Note:
After the update is completed, the machine reboots itself and returns to standby mode.
Repeat the above steps if there are additional firmware code files to be updated.
Confirm that the update was successfully completed by checking the Firmware Version with F9
Parameters F9-02-xx.
Caution:
If the unit does not boot up properly in step 8, refer to 2.6.8 (Firmware Emergency Recovery)
3) Preparing the Main Unit for the Programming Master Firmware Card
1. Turn the Power Switch on the left side and the Main Power Switch on the back of the machine to the
OFF position. (See 2.6.7.)
2. Insert the Flash Memory Card (4 MB or 8 MB) into the machine.
3. Turn the Main Power Switch on the back, and the Power Switch on the left side of the machine to
the ON position.
4. Press the "Function”, “Original Size (Ledger/A3)", and “3” keys simultaneously to enter the Service
Mode.
5. Enter the password, and select “OK” button (default password is 00000000).
6. Perform the Update Program Card Mode F9-09 (Update Program Card).
Repeat the above steps if there are additional master firmware cards to be programmed.
B. Copying the Firmware from an Existing Machine using a Flash Memory Card (4 MB or 8 MB)
1. Turn the Power Switch on the left side, and the Main Power Switch on the back of the machine to
the OFF position. (See 2.6.7.)
2. Install a Flash Memory Card (4 MB or 8 MB) into the machine.
3. Turn the Main Power Switch on the back, and the Power Switch on the left side of the machine to
the ON position.
4. Press the "Function”, “Original Size (Ledger/A3)", and “3” keys simultaneously to enter the Service
Mode.
5. Enter the password, and select “OK” button (default password is 00000000).
6. Perform the Copy Service Mode F9-08 (Program Backup).
7. The firmware is copied into the Flash Memory Card.
8. After the backup is completed, press "Stop" first, and then press "Function" + "C”(CLEAR) keys
simultaneously to return to standby.
9. Turn the Power Switch on the left side, and the Main Power Switch on the back of the machine to
the OFF position. (See 2.6.7.)
10. Remove the Master Firmware Card that you just created from the machine.
11. Turn the Main Power Switch on the back, and the Power Switch on the left side of the machine to
Ver. 1.1
48 DEC 2006
DP-8060/8045/8035
the ON position.
12. Use this Master Firmware Card to update the firmware on other machines.
Whichever method you select, it is easier to restore the machine's firmware to the Standard (AAV) Type
first, as it only requires 3 files to bring the machine to initial working condition. (Install the files in this
order: SC, SPC and PNL).
After recovering, if optional PCL or PS/PCL firmware is required, use the Network Firmware Update
Tool or the Local Firmware Update Tool to update the firmware to the required level.
If the unit does not boot up properly, follow the steps below:
1. Turn the power Off (use the power switch on the back of the unit, not the side of the unit).
- Before proceeding to the next step, you must prepare either the Local Firmware Update Tool, or
create the Master Firmware Flash Cards (read the appropriate sections first).
- If using the Master Firmware Card, insert the Master Firmware Flash Cards in the unit.
2. Turn the power On while holding the [Energy Saver] button.
3. When the green lamp on the front panel turns On, release the [Energy Saver] button.
- If using the Master Firmware Card, the unit will start updating the Firmware code files
automatically.
The unit is now ready to accept the firmware code from the Parallel Port, or Master Firmware Card.
Repeat the above steps if there are additional firmware code files to be updated.
Ver. 1.1
50 DEC 2006
DP-8060/8045/8035
2.6.9. Firmware Version
Firmware Type
B : Standard / Optional
C, D, E : Optional
Model Number
PNL : MK3 PNL A x Vxxxxx (a) PU (AU)
Destination Code (Fax)
AU : USA/Canada
AB : UK
Destination Code (Copier)
PU : USA/Canada
PB : UK
Division Soft
(When it is devided into (a) and (b))
Firmware Version (V1xxxx)
Language Code
A : A-English, C-French & Spanish
B : A-English, Spanish,German,
French & Italian
etc.
Firmware Type
A : Standard
Panel
Model Number
Model Number
Ver. 1.1
Adjustment Image
Toner OPC PWM Copy
Drum LSU Density
Optics Density TDC Adj. Counter Adj. Quality
No. Work Unit Adj. Adj. F6-49 Remark
Clean Sensor F8-09 Reset F6-39/52 (Note 5) Check
Clean /50/51
Part Item Clean F8-14 (Note 2) (Note 1)
(Note 3, 4)
1 Installation Main 1 2 3 4
2 Cleaning Optics 1 2 3
3 Drum Unit 1 2 3 4 5
4 Toner Density 1 2 3 4
Sensor
5 Replace Exposure Lamp 1 2 3
6 Platen Glass 1 2
7 OPC Drum 1 2 3 4 5
8 Developer 1 2 3
9 OPC Drum & 1 2 3 4 5 6
Developer
10 Corona Unit 1 2
52
11 Drum Unit 1 2 3
12 Toner Density 1 2 3
Sensor
13 TDC Sensor 1 2 3 Replace Developer
14 LSU 1 2 3 4
Copy Quality Adjustment Procedure (Order)
2. F6-28, and 29 should not be adjusted in the field. (The values must be set to "0")
DP-8060/8045/8035
DEC 2006
DP-8060/8045/8035
Note:
1. Copy Quality Check
1) Press the "Function”, “Original Size (Ledger/A3)", and “3” keys simultaneously to enter the Service
Mode.
2) Enter the password, and select “OK” button (default password is 00000000).
3) Press the "6", and then "Start" keys to enter the F6 Mode (Adjust Parameters).
4) Select "29 QUANTUM Black Density".
5) Select "INPUT" button, and enter a number
(0 → 1 or 1 → 0).
6) Select "OK" button 2 times.
7) Wait approximately 30 seconds.
8) The Machine starts QUANTUM Control automatically.
2. PWM Adjustment
1) It is recommended to make continuous copies (50 ~ 300 copies, depending on the machine model)
to stabilize the Bias Voltage of the Developer.
DP-8035 : 250 ~ 300 copies
DP-8045 : 150 ~ 200 copies
DP-8060 : 50 ~ 100 copies
2) Ensure that Ledger / A3 Size Paper is loaded in one of the Trays, and pull out the remaining trays
(including the bypass tray) to disable them.
3) Press the "Function”, “Original Size (Ledger/A3)", and “3” keys simultaneously to enter the Service
Mode.
4) Enter the password, and touch “OK” button (default password is 00000000).
5) Press the "8", and then "Start" keys to enter the F8 Mode (Service Adjustment).
6) Select "17 LSU PWM Pattern 1" to print the Test Pattern.
7) Observe the position of the uppermost visible gray patch.
Sample:
4 gray patches are visible in the illustration, the value of the uppermost patch position is "+2" in
our example.
(-5)
(0)
+2
(+5)
Test Pattern
F8-09 (Installation & Developer Replace) F8-14 (Installation & OPC Replace)
OPC
TDC Adjust
Counter Reset
7 min 3 sec
Ver. 1.1
54 DEC 2006
DP-8060/8045/8035
3.3. QUANTUM Control Timing
Refer to the following Table.
2 At 200, 400, 600, 800, and 1000 prints after F8-09 was Upon reaching the specified
performed number of prints *2
3 Every 1000 prints from 1001 prints after F8-09 was Upon reaching the specified
performed number of prints *2
4 When the F6-28 value is changed Upon returning to F6 initial display
11 At 100 prints after the Auto Off mode was cancelled When reaching the counters *2
<Note>
*1) Start timing of QUANTUM:
- QUANTUM starts when the machine is ready (It will not work during copy/print/fax operation)
- The start of QUANTUM may change depending on machine status
*2) Any print value numbers shown above, refers to the Total Counter
1) Press the "Function”, “Original Size (Ledger/A3)", and “3” keys simultaneously to enter the Service
Mode.
2) Enter the password, and select “OK” button (default password is 00000000).
3) Press the "2", and then "Start" keys to enter the F2 Mode.
4) Set the exposure to the center position.
Set the machine to TEXT / PHOTO Mode.
5) Make a copy of Test Chart 53/54 with gray scale (P/N FQ-SJ1011), and verify the density as shown
below. If it is within specification, skip to step (15).
a. Gray scale "1" should not be visible.
b. Gray scale "2" should be clearly visible.
A
. . . . . .
. . . . .. . . . . . 1 .
. .
2
Ver. 1.1
56 DEC 2006
DP-8060/8045/8035
5. Contrast Adjusting
Before making any adjustments, confirm that the following contents (F6-17, 18, and 19) are set to "-30",
“-3“, “-10“.
DO NOT adjust these codes in the field.
1) Press the "Function”, “Original Size (Ledger/A3)", and “3” keys simultaneously to enter the Service
Mode.
2) Enter the password, and select “OK” button (default password is 00000000).
3) Press the "2", and then "Start" keys to enter the F2 Mode.
4) Set the exposure to the center position.
Set the machine to TEXT / PHOTO Mode.
5) Make a copy of Test Chart 53/54 with gray scale (P/N FQ-SJ1011), and verify the density as shown
below. If it is within specification, skip to step (15).
a. Gray scale "1" should not be visible.
b. Gray scale "2" should be clearly visible.
A
. . . . . .
. . . . .. . . . . . 1 .
. .
2
6. LSU Adjustment
Refer to 2.8.
5 mm
Top (Lead edge)
5 mm (5 mm)
Ver. 1.1
58 DEC 2006
DP-8060/8045/8035
6. Perform the Service Mode F6-16, to adjust the gap to be 5 mm.
7. If the gap is less than 5 mm, input a (+) value. If more than 5 mm, input a (-) value.
8. Press the “Stop” key first, then press the “Function”, and “C” (Clear) keys simultaneously to exit the
Service Mode.
Ver. 1.1
60 DEC 2006
DP-8060/8045/8035
2.10. Signal Waveform
2.10.1. Glossary of Electrical Abbreviations
Ver. 1.1
62 DEC 2006
DP-8060/8045/8035
Signal Name Function
DFLD Driver FIFO Clock
DFLTH Driver FIFO Latch
DFOUT Driver FIFO Data Out
DFRST Driver FIFO Data Reset
DMBRAKE OPC Drum Motor Brake
DMCLK Drum Motor Clock
DMCLK OPC Drum Motor Clock
DMLD OPC Drum Motor Lock Detection Signal
DMPS OPC Drum Motor Start/Stop
DOSN Door Open Sensor Detection Signal
DXCL1 ADU Clutch 1 Control Signal
DXSLCNT1 Inverting Solenoid Control 1 Signal
DXSLCNT2 Inverting Solenoid Control 2 Signal
DXSN Inverting Path Sensor Detection Signal
ELPCNT Discharge Lamp
EXDOSN2 Paper Exit Door Sensor Detection Signal
EXFL1 Exit Fan 1 Lock Detection Signal
EXFL2 Exit Fan 2 Lock Detection Signal
EXFL3 Exit Fan 3 Lock Detection Signal
EXFM1 Exit Fan 1 Control Signal
EXFM2 Exit Fan 2 Control Signal
EXFM3 Exit Fan 3 Control Signal
EXSN Paper Exit Sensor Detection Signal
FULP1 AC Power Supply
FULP2 AC Power Supply
FULP3 AC Power Supply
GND Ground
GOPSW1 Developer Missing Detection
GREFCNT Grid Reference PWM
HEATL AC Power Supply
HFCL Sheet Bypass Clutch Control Signal
HFSOL Sheet Bypass Solenoid Control Signal
HPESN Sheet Bypass Sensor Detection Signal
HPSN Scanner Home Position Sensor Signal
HSSN1 Sheet Bypass Sensor 1 Signal
HSSN2 Sheet Bypass Sensor 2 Signal
HSSN3 Sheet Bypass Sensor 3 Signal
HSYNC Horizontal Synchronous Signal
HUMSN Temp Humidity Sensor Signal
HVBACCLK Bias AC Clock
HVBACCNT Bias AC ON/OFF, PWM
HVBDCCNT Bias DC ON/OFF, PWM
HVCNT Charge Corona ON/OFF, PWM
HVDACCNT Separation AC ON/OFF, PWM
HVDDCCNT Separation DC ON/OFF, PWM
HVLKB Bias Leak Detection
HVLKC High Voltage Leak Detection
Ver. 1.1
64 DEC 2006
DP-8060/8045/8035
Signal Name Function
LPFCL ADU Clutch 2 Control Signal
LPPSN Paper Path Sensor Signal
LPUSOL Paper Feed Solenoid Control Signal
LUM1 2nd Tray Lift Up Motor Control Signal
LUM1-1 +24 VDC Power Supply
LUM1-2 LUM1 Control Signal
LUM2-1 +24 VDC Power Supply
LUM2-2 LUM2 Control Signal
MAGCL Magnetic Roller Clutch Control Signal
MMA ADF Main Motor A Signal
MMAB ADF Main Motor AB Signal
MMB ADF Main Motor B Signal
MMBB ADF Main Motor BB Signal
MMCLK Main Motor Clock
MMFR Main Motor CW/CCW
MMLD Main Motor Lock Detection Signal
MMPS Main Motor Start/Stop
N.C. Not Used
nACK ACK Signal
nADFSES ADF Document Detect
nATT Attention Signal
nAUTFD Auto Feed Signal
nCTON Ring Detection Signal
nDUACK ADU Printer ACK Signal
nDUPRNT ADU Print Request Signal
nERROR Error Signal
nFAXRST FAX Board Reset Signal
nGARST CCD PCB Reset Signal
nHKOF External Phone Off-Hook Detection Signal
nLD1 Laser 1 Control Signal (-)
nLD2 Laser 2 Control Signal (-)
nLPOW1 Not Used
nLPOW2 Not Used
nPACK Printer ACK Signal
nPCIRING FAX Wake Up Signal
nPNLRST Panel Reset Signal
nPRDY Printer Ready Signal
nPRGDWN F-ROM Rewrite
nPRST SPC Reset Signal</p>0: Reset
nPVSYNC Print Registration
nSACK Scan ACK Signal
nSELIN Select Input Signal
nSENTIM Scanner LSYNC Signal
nSLPKY Sleep Key
nSREQ Scanner Request Signal
nSTROB Strobe Signal
nSTRX Sorter Reception (-)
Ver. 1.1
66 DEC 2006
DP-8060/8045/8035
Signal Name Function
PESN1 Paper Sensor Detection Signal
PESN1 Paper Sensor-1
PESN2 Paper Sensor-2
PEWSSN1 Paper Remaining Sensor 1 Signal
PEWSSN2 Paper Remaining Sensor 2 Signal
PEWSSN3 Paper Remaining Sensor 3 Signal
PFCL1 Paper Feed Clutch Control Signal
PFCL1 Paper Feed Clutch-1 Control Signal
PFCL2 Paper Feed Clutch-2 Control Signal
PFCLCNT Paper Feed Clutch Control Signal
PFOSN1 Paper Exit Sensor 1 Detection Signal
PFOSN2 Paper Exit Sensor 2 Detection Signal
PFSIZSN1 Paper Size Sensor 1 Signal
PFSIZSN2 Paper Size Sensor 2 Signal
PFSIZSN3 Paper Size Sensor 3 Signal
PGND Ground
pINIT Initiation
pLD1 Laser 1 Control Signal (+)
pLD2 Laser 2 Control Signal (+)
PMA Paper Feed Motor A Signal
PMAB Paper Feed Motor AB Signal
PMB Paper Feed Motor B Signal
PMBB Paper Feed Motor BB Signal
PMCLK Polygon Motor Clock
PMCNT Polygon Motor Control Signal
PMLOCK Polygon Motor Lock Signal
PNLDO1 Panel F-ROM Rewrite Serial Data
PNLSCLK1 Panel F-ROM Rewrite Serial Clock
POWSW POW SW
pPRXD Reception Data Signal
PPSOLCNT Pinch Solenoid Control Signal
pPTXD Transmission Data Signal
PR1SN Registration Sensor 1 Signal
pSELECT Paper Select Signal
pSPKOT Line Signal, Dial Tone
pSTRX Sorter Reception Signal (+)
pSTTX Sorter Transmission Signal (+)
PTG CCD Shift GATE Signal
PTL Pre Transfer Lamp
PUSOL1 Paper Feed Solenoid Control Signal
PUSOL1 Paper Feed Solenoid-1 Control Signal
PUSOL2 Paper Feed Solenoid-2 Control Signal
PVCNT Printer 24V Control
PWFL PS Fan Lock Detection Signal
PWFM PS Fan Control Signal
QDOSN Door Open Sensor Detection Signal
RR1CLCNT Registration Roller 1 Clutch Control Signal
Ver. 1.1
68 DEC 2006
DP-8060/8045/8035
Signal Name Function
Vcnt Inverter Control Signal
VTED Toner Detect Sensor ON
WEBSOL Web Solenoid Control Signal
ZCIN Zero Cross
ZNSN1a Paper Remaining Sensor a Signal (Upper)
ZNSN1b Paper Remaining Sensor b Signal (Upper)
ZNSN1c Paper Remaining Sensor c Signal (Upper)
ZNSN2a Paper Remaining Sensor a Signal (Lower)
ZNSN2b Paper Remaining Sensor b Signal (Lower)
ZNSN2c Paper Remaining Sensor c Signal (Lower)
ZNSNa Paper Remaining Sensor a
ZNSNb Paper Remaining Sensor b
ZNSNc Paper Remaining Sensor c
0V
0V
Ver. 1.1
70 DEC 2006
DP-8060/8045/8035
SC PCB
Signal Name Destination Signal Waveform Function
Pin No.
CN51-12 +3.3V DC PCB +3.3 VDC Power Supply
+3.3V
CN143-13
CN52
SC PCB
Signal Name Destination Signal Waveform Function
Pin No.
CN52-1 +24V PNL1 PCB +24V +24 VDC Power Supply
CN220-1
0V
0V
0V
0V
0V
0V
0V
CN53
SC PCB
Signal Name Destination Signal Waveform Function
Pin No.
CN53-1 nPRDY SPC PCB Printer Ready Signal
CN702-1 +5V
0V
0V
0V
0V
Ver. 1.1
72 DEC 2006
DP-8060/8045/8035
SC PCB
Signal Name Destination Signal Waveform Function
Pin No.
CN53-5 nDUACK SPC PCB ADU Printer ACK Signal
CN702-5 +5V
0V
0V
0V
0V
0V
0V
0V
0V
0V
0V
0V
CN54
SC PCB
Signal Name Destination Signal Waveform Function
Pin No.
CN54-1 IICSDA SPC PCB IIC Transmission Signal
CN703-1 +5V
0V
0V
0V
0V
CN55
SC PCB
Signal Name Destination Signal Waveform Function
Pin No.
CN55-1 GACLK- CCD PCB Gate Array Clock-
CN850-1 +1.3V
+1.1V
Ver. 1.1
74 DEC 2006
DP-8060/8045/8035
SC PCB
Signal Name Destination Signal Waveform Function
Pin No.
CN55-2 GND CCD PCB Ground
CN850-2
0V
+1.1V
+1.1V
+1.1V
+1.1V
+1.1V
+1.1V
+1.1V
+1.1V
+1.1V
+1.1V
+1.1V
+1.1V
+1.1V
Ver. 1.1
76 DEC 2006
DP-8060/8045/8035
SC PCB
Signal Name Destination Signal Waveform Function
Pin No.
CN55-25 CLIPIN CCD PCB AFE Sample Hold Clamp
CN850-25 3.3V Signal
0V
0V
0V
0V
0V
0V
Ver. 1.1
78 DEC 2006
DP-8060/8045/8035
SC PCB
Signal Name Destination Signal Waveform Function
Pin No.
CN55-48 nGARST CCD PCB CCD PCB Reset Signal
CN850-48 3.3V
RESE
0V
CN57
SC PCB
Signal Name Destination Signal Waveform Function
Pin No.
CN57-1 +3.3V LSU PCB +3.3 VDC Power Supply
+3.3V
CN551-1
0V
0V
0V
0V
CN58
SC PCB
Signal Name Destination Signal Waveform Function
Pin No.
CN58-1 GND PR CON PCB Ground
CN210-1
0V
0V
0V
0V
0V
0V
0V
Ver. 1.1
80 DEC 2006
DP-8060/8045/8035
SC PCB
Signal Name Destination Signal Waveform Function
Pin No.
CN58-13 PD4 PR CON PCB Data Signal
CN210-7 +5V
0V
0V
0V
0V
0V
0V
0V
0V
0V
0V
0V
CN59
SC PCB
Signal Name Destination Signal Waveform Function
Pin No.
CN59-1 ATRST HDD Reset Signal
+5V
CNSHD1-1
RESET
0V
0V
0V
0V
Ver. 1.1
82 DEC 2006
DP-8060/8045/8035
SC PCB
Signal Name Destination Signal Waveform Function
Pin No.
CN59-6 ATD9 HDD HDD Data Bus
CNSHD1-6 +5V
0V
0V
0V
0V
0V
0V
0V
0V
0V
0V
0V
0V
0V
0V
0V
0V
0V
Ver. 1.1
84 DEC 2006
DP-8060/8045/8035
SC PCB
Signal Name Destination Signal Waveform Function
Pin No.
CN59-28 CSEL HDD Cable Select Signal
CNSHD1-28 +5V
0V
0V
0V
0V
0V
0V
0V
0V
0V
0V
0V
Ver. 1.1
86 DEC 2006
DP-8060/8045/8035
2.12. PNL1 PC Board
CN220
Refer to SC PC Board CN52.
CN221
PNL1 PCB
Signal Name Destination Signal Waveform Function
Pin No.
CN221-1 nADFSES DRV PCB ADF Document Detect
CN767-2
Detect
CN222
PNL1 PCB
Signal Name Destination Signal Waveform Function
Pin No.
CN222-1 POWSW SW POW SW
OFF
SW ON
0V
CN224
PNL1 PCB
Signal Name Destination Signal Waveform Function
Pin No.
CN224-1 +24V INV PCB +24V +24 VDC Power Supply
CN1-1
CLK 0V
CLK 0V
RESET 0V
Ver. 1.1
88 DEC 2006
DP-8060/8045/8035
ADF PCB
Signal Name Destination Signal Waveform Function
Pin No.
CN650-12 N.C. Not Used
CN651
ADF PCB
Signal Name Destination Signal Waveform Function
Pin No.
CN651-1 AFDOUT SPC PCB FIFO Data In
CN704-1 +5V
Pluse 0V
0V
0V
CLK 0V
Pluse 0V
CN652
ADF PCB
Signal Name Destination Signal Waveform Function
Pin No.
CN652-1 N.C. Not Used
0V
0V
0V
0V
Ver. 1.1
90 DEC 2006
DP-8060/8045/8035
CN653
ADF PCB
Signal Name Destination Signal Waveform Function
Pin No.
CN653-1 GND Registration Ground
Sensor 1-3
0V
0V
CN654
ADF PCB
Signal Name Destination Signal Waveform Function
Pin No.
CN654-1 N.C. Not Used
CN655
ADF PCB
Signal Name Destination Signal Waveform Function
Pin No.
CN655-1 +24VO1 Paper Feed +24V +24 VDC Power Supply
Clutch
0V
Ver. 1.1
92 DEC 2006
DP-8060/8045/8035
ADF PCB
Signal Name Destination Signal Waveform Function
Pin No.
CN655-5 OPSN Door Sensor-2 ADF Cover Open Detection
+5V Signal
Open
Close
0V
CN656
ADF PCB
Signal Name Destination Signal Waveform Function
Pin No.
CN656-1 +24VO1 Registration +24V +24 VDC Power Supply
Clutch 2
CN658
ADF PCB
Signal Name Destination Signal Waveform Function
Pin No.
CN658-1 +24VO1 Stamp +24V +24 VDC Power Supply
0V
CN659
ADF PCB
Signal Name Destination Signal Waveform Function
Pin No.
CN659-1 N.C. Not Used
CN660
ADF PCB
Signal Name Destination Signal Waveform Function
Pin No.
CN660-1 +24VO1 Pinch Solenoid +24V +24 VDC Power Supply
Ver. 1.1
94 DEC 2006
DP-8060/8045/8035
ADF PCB
Signal Name Destination Signal Waveform Function
Pin No.
CN660-2 PPSOLCNT Pinch Solenoid Pinch Solenoid Control
+24V Signal
OFF
ON
0V
CN661
ADF PCB
Signal Name Destination Signal Waveform Function
Pin No.
CN661-1 N.C. Not Used
0V
0V
0V
0V
0V
0V
0V
0V
CN662
ADF PCB
Signal Name Destination Signal Waveform Function
Pin No.
CN662-1 N.C. Not Used
Ver. 1.1
96 DEC 2006
DP-8060/8045/8035
ADF PCB
Signal Name Destination Signal Waveform Function
Pin No.
CN662-3 +24VO1 DRV PCB +24V +24 VDC Power Supply
CN753-2
CN702
Refer to SC PC Board CN53.
CN703
Refer to SC PC Board CN54.
CN704
Refer to ADF PC Board CN650 and CN651.
Ver. 1.1
98 DEC 2006
DP-8060/8045/8035
CN705
SPC PCB
Signal Name Destination Signal Waveform Function
Pin No.
CN705-1 ORSIZ1 Original Size Original Size Sensor
Sensor 1-1 +5V Signal 0
Detect
0V
CN706
SPC PCB
Signal Name Destination Signal Waveform Function
Pin No.
CN706-1 DFOUT DRV PCB Driver FIFO Data Out
CN766-1 +5V
0V
0V
0V
CLK 0V
0V
0V
0V
Ver. 1.1
100 DEC 2006
DP-8060/8045/8035
SPC PCB
Signal Name Destination Signal Waveform Function
Pin No.
CN706-8 LMCLK DRV PCB Scanner Motor Clock
CN766-8 +5V
CLK 0V
CLK 0V
CLK 0V
CLK 0V
0V
CN707
SPC PCB
Signal Name Destination Signal Waveform Function
Pin No.
CN707-1 OQFDOUT System Console OQ FIFO Data Out
Connector +5V
CNA-2
0V
Ver. 1.1
102 DEC 2006
DP-8060/8045/8035
SPC PCB
Signal Name Destination Signal Waveform Function
Pin No.
CN707-9 +5V System Console +5V +5 VDC Power Supply
Connector
CNB-4
CN708
SPC PCB
Signal Name Destination Signal Waveform Function
Pin No.
CN708-1 nSTRX Finisher Sorter Reception Signal (-)
Connector-8 +5V
CLK 0V
CLK 0V
CLK 0V
CLK 0V
CLK 0V
CLK 0V
CN709
SPC PCB
Signal Name Destination Signal Waveform Function
Pin No.
CN709-1 GND Size Sensor 1-3 Ground
0V
0V
0V
0V
0V
0V
Ver. 1.1
104 DEC 2006
DP-8060/8045/8035
CN710
SPC PCB
Signal Name Destination Signal Waveform Function
Pin No.
CN710-1 +24VM Paper Feed +24V +24 VDC Power Supply
Clutch
0V
0V
0V
0V
Ver. 1.1
106 DEC 2006
DP-8060/8045/8035
CN711
SPC PCB
Signal Name Destination Signal Waveform Function
Pin No.
CN711-1 +24VM 2nd Tray Lift Up +24V +24 VDC Power Supply
Motor
CN712
SPC PCB
Signal Name Destination Signal Waveform Function
Pin No.
CN712-1 +24VM Paper Feed +24V +24 VDC Power Supply
Clutch
0V
0V
Ver. 1.1
108 DEC 2006
DP-8060/8045/8035
SPC PCB
Signal Name Destination Signal Waveform Function
Pin No.
CN712-21 GND Paper Sensor 2-3 Ground
0V
0V
CN713
SPC PCB
Signal Name Destination Signal Waveform Function
Pin No.
CN713-1 +24VM 1st Tray Lift Up +24V +24 VDC Power Supply
Motor
CN714
SPC PCB
Signal Name Destination Signal Waveform Function
Pin No.
CN714-1 +24VM ADU Clutch +24V +24 VDC Power Supply
CN715
SPC PCB
Signal Name Destination Signal Waveform Function
Pin No.
CN715-1 +5V Timing Sensor-1 +5V +5 VDC Power Supply
0V
Ver. 1.1
110 DEC 2006
DP-8060/8045/8035
SPC PCB
Signal Name Destination Signal Waveform Function
Pin No.
CN715-10 SPPSN System Console System Paper Path Sensor
Sensor-2 +5V Signal
Detect
0V
CN716
SPC PCB
Signal Name Destination Signal Waveform Function
Pin No.
CN716-1 +24VM Pre Transfer +24V +24 VDC Power Supply
Lamp-1
0V
CN717
SPC PCB
Signal Name Destination Signal Waveform Function
Pin No.
CN717-1 +5V Sheet Bypass +5V +5 VDC Power Supply
Sensor 3-1
Ver. 1.1
112 DEC 2006
DP-8060/8045/8035
SPC PCB
Signal Name Destination Signal Waveform Function
Pin No.
CN717-2 HSSN3 Sheet Bypass Sheet Bypass Sensor 3
Sensor 3-2 +5V Signal
Detect
0V
CN718
SPC PCB
Signal Name Destination Signal Waveform Function
Pin No.
CN718-1 +24VM Sheet Bypass +24V +24 VDC Power Supply
Solenoid
CN719
SPC PCB
Signal Name Destination Signal Waveform Function
Pin No.
CN719-1 BMBB Toner Bottle Toner Bottle Motor BB Clock
Motor-6 +24V
CLK 0V
CLK 0V
CLK 0V
CLK 0V
Pluse 0V
Ver. 1.1
114 DEC 2006
DP-8060/8045/8035
SPC PCB
Signal Name Destination Signal Waveform Function
Pin No.
CN719-8 VTED Toner Detect Toner Detect Sensor ON
Sensor-3 +5V
ON 0V
CN720
SPC PCB
Signal Name Destination Signal Waveform Function
Pin No.
CN720-1 GOPSW1 CN720-6 Developer Missing
+5V Detection
Detect
0V
0V
0V
0V
0V
0V
ON 0V
0V
CN722
SPC PCB
Signal Name Destination Signal Waveform Function
Pin No.
CN722-1 +5V Temp Humidity +5V +5 VDC Power Supply
Sensor-1
0V
0V
CN723
SPC PCB
Signal Name Destination Signal Waveform Function
Pin No.
CN723-1 GND ACD PCB Ground
CN106-9
0V
Ver. 1.1
116 DEC 2006
DP-8060/8045/8035
SPC PCB
Signal Name Destination Signal Waveform Function
Pin No.
CN723-2 ZCIN ACD PCB Zero Cross
CN106-8 +5V
0V
0V
0V
0V
2.7V
0V
CLK 0V
CLK 0V
CLK 0V
CLK 0V
CLK 0V
CLK 0V
Ver. 1.1
118 DEC 2006
DP-8060/8045/8035
SPC PCB
Signal Name Destination Signal Waveform Function
Pin No.
CN724-12 HVDACCNT HVPS Separation AC ON/OFF,
CNHV-12 +5V PWM
CLK 0V
CLK 0V
CN725
SPC PCB
Signal Name Destination Signal Waveform Function
Pin No.
CN725-1 +24VM LSU +24V +24 VDC Power Supply
CN550-5
CLK 0V
CN726
SPC PCB
Signal Name Destination Signal Waveform Function
Pin No.
CN726-1 +5VL LSU +5V +5 VDC Power Supply
CN552-1
0V
0V
0V
0V
Ver. 1.1
120 DEC 2006
DP-8060/8045/8035
2.15. DRV PC Board
CN750
DRV PCB
Signal Name Destination Signal Waveform Function
Pin No.
CN750-1 +24V LVPS +24V +24 VDC Power Supply
CN2-1
CN751
DRV PCB
Signal Name Destination Signal Waveform Function
Pin No.
CN751-1 +5VP DC PCB +5V +5 VDC Power Supply
CN144-1
CN752
Refer to SPC PC Board CN701.
CN753
Refer to ADF PC Board CN662.
CN754
DRV PCB
Signal Name Destination Signal Waveform Function
Pin No.
CN754-1 +24VO2 System Console +24V +24 VDC Power Supply
Connector
CNA-1
Ver. 1.1
122 DEC 2006
DP-8060/8045/8035
CN756
DRV PCB
Signal Name Destination Signal Waveform Function
Pin No.
CN756-1 LMA Scan Motor-1 +24V Scan Motor A Signal
0V
0V
0V
0V
0V
CN757
DRV PCB
Signal Name Destination Signal Waveform Function
Pin No.
CN757-1 PGND Fan1-3 Ground
0V
Ver. 1.1
124 DEC 2006
DP-8060/8045/8035
DRV PCB
Signal Name Destination Signal Waveform Function
Pin No.
CN757-5 EXFM1 Fan1-1 Exit Fan 1 Control Signal
+24V
ON
OFF
0V
CN758
DRV PCB
Signal Name Destination Signal Waveform Function
Pin No.
CN758-1 PGND Ozone Fan-3 Ground
0V
0V
0V
0V
CN759
DRV PCB
Signal Name Destination Signal Waveform Function
Pin No.
CN759-1 PGND Fan2-3 Ground
0V
0V
Ver. 1.1
126 DEC 2006
DP-8060/8045/8035
DRV PCB
Signal Name Destination Signal Waveform Function
Pin No.
CN759-8 PFOSN1 Paper Exit Paper Exit Sensor 1
Sensor-2 +5V Detection Signal
Not Detect
Detect
0V
CN760
DRV PCB
Signal Name Destination Signal Waveform Function
Pin No.
CN760-1 +24VM Main Drive Motor +24V +24 VDC Power Supply
CNMM1-1
CN761
DRV PCB
Signal Name Destination Signal Waveform Function
Pin No.
CN761-1 N.C. Main Drive Motor Not Used
CNMM2-10
CLK 0V
CN761-12 +24VM OPC Drum Motor +24V +24 VDC Power Supply
CNDM1-10
CN761-13 +24VM OPC Drum Motor +24V +24 VDC Power Supply
CNDM1-9
Ver. 1.1
128 DEC 2006
DP-8060/8045/8035
DRV PCB
Signal Name Destination Signal Waveform Function
Pin No.
CN761-14 PGND OPC Drum Motor Ground
CNDM1-8
0V
CLK 0V
CN762
DRV PCB
Signal Name Destination Signal Waveform Function
Pin No.
CN762-1 CLMM1 Corona Wire Corona Wire Cleaner Motor
Cleaner Motor +24V Control Signal
CCW
CW
0V
CN763
DRV PCB
Signal Name Destination Signal Waveform Function
Pin No.
CN763-1 RVMA Inverting Motor-1 +24V Inverting Motor A Signal
0V
0V
0V
Ver. 1.1
130 DEC 2006
DP-8060/8045/8035
DRV PCB
Signal Name Destination Signal Waveform Function
Pin No.
CN763-6 RVMBB Inverting Motor-6 +24V Inverting Motor BB Signal
0V
CN764
DRV PCB
Signal Name Destination Signal Waveform Function
Pin No.
CN764-1 +24VM Separation +24V +24 VDC Power Supply
Solenoid
Ver. 1.1
132 DEC 2006
DP-8060/8045/8035
DRV PCB
Signal Name Destination Signal Waveform Function
Pin No.
CN764-5 N.C. Not Used
0V
CN766
Refer to SPC PC Board CN706.
CN767
Refer to PNL1 PC Board CN221.
CN768
DRV PCB
Signal Name Destination Signal Waveform Function
Pin No.
CN768-1 +24VM ELP-1 +24V +24 VDC Power Supply
Ver. 1.1
134 DEC 2006
DP-8060/8045/8035
DRV PCB
Signal Name Destination Signal Waveform Function
Pin No.
CN768-4 ELPCNT ELP-2 Discharge Lamp
+24V
OFF
ON
0V
0V
CN102
ACD PCB
Signal Name Destination Signal Waveform Function
Pin No.
CN102-1 ACL Option LVPS AC Power Supply
CN64-1
AC120V
(AC200-240V)
CN103
ACD PCB
Signal Name Destination Signal Waveform Function
Pin No.
CN103-1 ACL LVPS AC Power Supply
CN1-1
AC120V
(AC200-240V)
Ver. 1.1
136 DEC 2006
DP-8060/8045/8035
CN104
ACD PCB
Signal Name Destination Signal Waveform Function
Pin No.
CN104-1 ACL NFL PCB AC Power Supply
CN133-3
AC120V
(AC200-240V)
CN105
ACD PCB
Signal Name Destination Signal Waveform Function
Pin No.
CN105-1 HEATL Thermostat AC Power Supply
Thermal Fuse
AC120V
(AC200-240V)
AC120V
(AC200-240V)
AC120V
(AC200-240V)
CN106
Refer to SPC PC Board CN723.
AC120V
(AC200-240V)
CN133
Refer to ACD PC Board CN104.
CN134
NFL PCB
Signal Name Destination Signal Waveform Function
Pin No.
CN134-1 ACNRLB RLB PCB AC Power Supply
CN171-1
AC120V
Ver. 1.1
138 DEC 2006
DP-8060/8045/8035
2.18. DC PC Board
CN141
DC PCB
Signal Name Destination Signal Waveform Function
Pin No.
CN141-1 GND LVPS Ground
CN3-1
0V
CN142
DC PCB
Signal Name Destination Signal Waveform Function
Pin No.
CN142-1 GND LVPS Ground
CN4-1
0V
CN143
Refer to SC PC Board CN51.
CN144
Refer to DRV PC Board CN751.
CN145
DC PCB
Signal Name Destination Signal Waveform Function
Pin No.
CN145-1 GND DCB PCB Ground
CN142-5
0V
Ver. 1.1
140 DEC 2006
DP-8060/8045/8035
2.19. DCB PC Board
CN141
Refer to DC PC Board CN145.
CN142
Refer to DC PC Board CN145.
CN143
DCB PCB
Signal Name Destination Signal Waveform Function
Pin No.
CN143-1 N.C. Not Used
Ver. 1.1
142 DEC 2006
DP-8060/8045/8035
2.20. CCD PCB
CN850
Refer to SC PC Board CN55.
CN550
Refer to SPC PC Board CN725.
CN551
Refer to SC PC Board CN57.
CN552
Refer to SPC PC Board CN726.
Ver. 1.1
144 DEC 2006
DP-8060/8045/8035
2.22. PRCON PCB
CN210, CN211
Refer to SC PC Board CN58.
CNHV
Refer to SPC PC Board CN724.
Ver. 1.1
146 DEC 2006
DP-8060/8045/8035
2.24. LVPS
CN1
Refer to ACD PC Board CN103.
CN2
Refer to DRV PC Board CN750.
CN3
Refer to DC PC Board CN141.
CN4
Refer to DC PC Board CN142.
CN64
Refer to ACD PC Board CN102.
CN65
LVPS
Signal Name Destination Signal Waveform Function
Pin No.
CN65-1 STRVP Finisher Control Signal
Connector-1 +24V
ON
OFF
0V
CN66
Refer to DC PC Board CN144.
Ver. 1.1
148 DEC 2006
DP-8060/8045/8035
2.26. APF PC Board
CN601
Refer to SPC PC Board CN707 and DRV PC Board CN754.
CN602
APF PCB
Signal Name Destination Signal Waveform Function
Pin No.
CN602-1 +24VO2 +24V +24 VDC Power Supply
ON 0V
CN602-6 PGND OQM-3 Ground
0V
0V
ON 0V
CN602-9 OQMLK OQM-6 +5V Drive Motor Lock Signal
Rotation 0V
CLK 0V
CLK 0V
CN603
APF PCB
Signal Name Destination Signal Waveform Function
Pin No.
CN603-1 LUM1-1 LUM1-1 +24V +24 VDC Power Supply
ON
CN604
APF PCB
Signal Name Destination Signal Waveform Function
Pin No.
CN604-1 LUM2-1 LUM2-1 +24V +24 VDC Power Supply
ON
CN605
APF PCB
Signal Name Destination Signal Waveform Function
Pin No.
CN605-1 +5V ZNSN1a-1 +5V +5 VDC Power Supply
Ver. 1.1
150 DEC 2006
DP-8060/8045/8035
APF PCB
Signal Name Destination Signal Waveform Function
Pin No.
CN605-5 GND ZNSN1a-3 Ground
0V
0V
0V
CN606
APF PCB
Signal Name Destination Signal Waveform Function
Pin No.
CN606-1 +5V ZNSN2a-1 +5V +5 VDC Power Supply
0V
0V
0V
CN607
APF PCB
Signal Name Destination Signal Waveform Function
Pin No.
CN607-1 +24VO2 PFCL1-1 +24V +24 VDC Power Supply
Ver. 1.1
152 DEC 2006
DP-8060/8045/8035
APF PCB
Signal Name Destination Signal Waveform Function
Pin No.
CN607-7 CPPSN1 CPPSN1-2 Paper Path Sensor 1 Signal
Pass
Upper Limit
0V
0V
Empty
0V
CN608
APF PCB
Signal Name Destination Signal Waveform Function
Pin No.
CN608-1 +24VO2 PFCL2-1 +24V +24 VDC Power Supply
Pass
Upper Limit
0V
0V
ON
0V
Ver. 1.1
154 DEC 2006
DP-8060/8045/8035
2.27. LCT PC Board
CN551
Refer to SPC PC Board CN707 and DRV PC Board CN754.
CN552
Refer to SPC PC Board CN707 and DRV PC Board CN754.
CN553
LCT PCB
Signal Name Destination Signal Waveform Function
Pin No.
CN553-1 GND Ground
0V
0V
0V
0V
CN554
LCT PCB
Signal Name Destination Signal Waveform Function
Pin No.
CN554-1 +24VO2 LPCSOL-1 +24V +24 VDC Power Supply
Upper Limit
Empty
0V
0V
Ver. 1.1
156 DEC 2006
DP-8060/8045/8035
LCT PCB
Signal Name Destination Signal Waveform Function
Pin No.
CN554-11 LOPSN LOPSN-2 Connect Detect Sensor
Signal
Connect Nonconnect
Pass
0V
0V
CN555
LCT PCB
Signal Name Destination Signal Waveform Function
Pin No.
CN555-1 GND LCDOSN-3 Ground
0V
0V
Lower Limit
0V
0V
CN556-4 LCMAB MM-3 Motor AB Signal
+3.3V
0V
0V
CN557
LCT PCB
Signal Name Destination Signal Waveform Function
Pin No.
CN557-1 LCLUM1 LUM Lift Motor Control Signal 1
+24V
Up
Down
0V
Ver. 1.1
158 DEC 2006
DP-8060/8045/8035
2.28. FXB PC Board
CN391
FXB PCB
Signal Name Destination Signal Waveform Function
Pin No.
CN391-1 +5VP MJR PCB +5V +5 VDC Power Supply
CN25-1
CN392
FXB PCB
Signal Name Destination Signal Waveform Function
Pin No.
CN392-1 L2 (T) MJR PCB Line Signal
CN22-1
0V
Ver. 1.1
160 DEC 2006
DP-8060/8045/8035
3 Troubleshooting
3.1. Error Codes (For Copier)
The self-diagnostic functions detect troubles in the important components of the copier.
When any trouble occurs, the copier stops.
3.1.1. User Error Codes (U Code)
Note:
Uxx, and a message will appear on the Panel Display.
I I
G Misfed Location Indicator
A
Indicates to open each cover, check,
and remove any misfed paper.
E
Note:
If the machine is jammed, follow the procedure below.
1. If the machine has the Hard Disk Drive Unit installed, turn the Power Switch on the Left Side of the
machine to the OFF position first. After waiting approximately 10 seconds, turn the Main Power
Switch on the Back of the machine to the OFF position. (This interrupts all the power to the
machine.)
Inverting Exit
Sensor Timing Sensor
Registration
Sensor
Inverting Paper Paper Path
Sensor Sensor
ADU Entrance
Sensor
ADU Intermediate 1st Paper Path
Sensor Sensor
ADU Exit Intermediate
Sensor Roller Sensor
Registration Roller
Lower Tray
Inverting Roller
Interstage Stack
START
END
memo
4 Service Modes
4.1. Service Modes (For Copier)
These Service Modes are provided to assist the technician in checking for abnormalities in the copier, and a
means of making adjustments to the Input/Output of major components.
Caution:
The factory default parameters are preset (country dependent) for optimum performance, and in
compliance with the local telecommunication regulations/standards, and do not need to be changed.
Changing some of these parameters may cause the unit to be no longer compliant, or become
inoperable.
4.1.1. Service Mode Procedure
1. To select the Service Mode
The Service Mode is selected when "Function", "Original Size (Ledger/A3)", and "3" keys on the
keypad are simultaneously pressed, enter the password, and select “OK” button (default password is
00000000), then F1 (Self Test) appears in the display.
F6-00 Adj 100% Side-Side Read 3 F6-50 T/P Mode Image Density 0
F6-01 Adj 100% Lead-Tail Read -3 F6-51 P Mode Image Density 15
F6-02 100% Selection 0 F6-52 LSU Unit PWM Adjust 1 2
F6-03 Original Registration 8 F6-53 CCD Read Position Adj. 5
F6-04 Printer Registration -3 F6-54 T Mode Contrast 0
F6-05 Main Motor Speed 0 F6-55 T/P Mode Contrast 0
F6-06 Polygon Motor Speed 0 F6-56 P Mode Contrast 0
F6-07 Registration Void 4 F6-57 Sep. DC Volt. 1-Sided 0
F6-08 Trail Edge Read Timing 0 F6-58 Sep. AC Volt. 1-Sided 0
F6-09 Trail Edge Print Timing 5 F6-59 Sep. DC Volt. 2-Sided 0
Ver. 1.1
185 DEC 2006
DP-8060/8045/8035
1.MACHINE INFORMATION
MACHINE NAME : DP-xxxx
MAC ADDRESS : xxxxxxxxxxxx
SERIAL NUMBER :
2.FIRMWARE VERSION
SC : BxVxxxxxPU
SC BOOT : Mxx
PNL : AxVxxxxxPU
SPC : 60cpm Vxxxx
FINISHER :
FAX MODEM : Ver xxxx
PDL FONT1 : CAVxxxxxxxx
SC2 : CAVxxxxxxxx
DATA SECURITY KIT : Vxxxxx(xxxxxxxx)
3.MEMORY CAPACITY
PAGE MEMORY : 32 MB
SORT MEMORY : 32 MB
FAX MEMRY : 3 MB
4.OPTION
DOCUMENT FEEDER (ADF) : Yes
3rd PAPER FEED MODULE : Yes
4th PAPER FEED MODULE : Yes
LCT : No
FINISHER : No
PUNCH UNIT : No
FAX BOARD : Yes
NETWORK SCANNER : Yes
PCL PRINTER : Yes
PS PRINTER : No
IPX/SPX : Yes
EMAIL : Yes
DDS : Yes
HDD : Yes
5.ERROR LOG
TOTAL PRINT COUNT : 18700
NO. DATE & TIME ERROR CODE ERROR COUNT NO. DATE & TIME ERROR CODE ERROR COUNT
--------------------------------------------------------------------------------
01 MMM-dd-yyyy 11:11 J27 XX-00000008
02 MMM-dd-yyyy 11:31 J41 XX-00000140
(See Remarks)
--------------------------------------------------------------------------------
Remarks:
XX-00000140
Page Count
00 : Printer Error
02 : Scanner Error
**********-F7 TOTAL COUNTER LIST-****** DATE MMM-dd-yyyy *** TIME12:01 *** P.01
Ver. 1.1
187 DEC 2006
DP-8060/8045/8035
4.1.3. F4 Mode: Input/Output Status Test
Set the machine to service mode, and press "4" key on the Keypad.
↓
Press the "Start" key.
↓
Enter the number to activate the test then press "Start" key.
↓
Press "Stop" key to cancel the test.
↓
When the "C (Clear)" key is pressed, the selected code input will not be utilized.
↓
Press "Function", and "C (Clear)" keys simultaneously to exit the service mode.
1. Input Check
Ver. 1.1
189 DEC 2006
DP-8060/8045/8035
F4 Mode (Input Check)
Message Display
No. Function Condition Remarks
7 6 5 4 3 2 1 0
005 Charge Corona Cleaning Cleaner is not detected. 0
End Detect Sensor
Charge Corona Cleaning Cleaner is detected. 1
Home position Sensor
Inverting Cover Sensor Cover is open. 1
Paper Exit Sensor Paper is detected. 0
Inverting Paper Sensor Paper is detected. 0
Inverting Sensor Paper is detected. 0
006 Dust Fan Lock Signal Normal. 0
Toner Waste Container Full Toner Waste Container 1
Detection Sensor is full.
007 Exhaust Fan 2 Lock Signal Normal. 0
Exhaust Fan 1 Lock Signal Normal. 0
Toner Waste Container Toner Waste Container 0
Detection Sensor is detected.
Suction Fan Lock Signal Normal. 0
008 Power Supply Fan Lock Normal. 0
Signal
Ozone Fan 2 Lock Signal Normal. 0
Exhaust Fan 3 Lock Signal Normal. 0
009 Cover Open/Close Sensor Cover is open. 1
(System Console)
Paper Path Sensor Paper is detected. 0
(4th Paper Tray)
Upper Limit Sensor Upper Limit is detected. 1
(4th Paper Tray)
NP Sensor Paper is not detected. 1
(4th Paper Tray)
Paper Remaining Sensor 3 Sensor is activated. 1
(4th Paper Tray)
Paper Remaining Sensor 2 Sensor is activated. 1
(4th Paper Tray)
Paper Remaining Sensor 1 Sensor is activated. 1
(4th Paper Tray)
Drive Motor Stop Signal Drive Motor is stopped. 1
(System Console)
Ver. 1.1
191 DEC 2006
DP-8060/8045/8035
F4 Mode (Input Check)
Message Display
No. Function Condition Remarks
7 6 5 4 3 2 1 0
015 Stapler Home Position Home position is 1
Sensor detected.
Entrance Paper Path Paper is detected. 0
Sensor
Buffer Paper Path Sensor Paper is detected. 0
Exit Paper Path Sensor Paper is detected. 0
Buffer Entrance Sensor Paper is detected. 0
016 Stapler Tray Sensor Paper is detected. 0
2nd Tray Sensor Paper is detected. 0
1st Tray Sensor Paper is detected. 0
Stapler Sensor Stapler is detected. 1
Stapler Cartridge Sensor Stapler Cartridge is 0
detected.
Stapler Unit Sensor Stapler Unit is detected. 0
017 Punch Upper Cover Cover is open. 1
Sensor
Punch Front Cover Sensor Cover is open. 1
Punch Move Home Home position is 0
Position Sensor detected.
Punch Home Position Home position is 1
Sensor detected.
Punch Unit Sensor Punch Unit is detected. 0
018 Rocking Guide Open Guide is open. 1
Sensor
Shutter Open Sensor Shutter is open. 1
Tray Unit Home Position Home position is 1
Sensor detected.
Collation Home Position Home position is 0
Sensor detected.
Stapler Home Position Home position is 0
Sensor detected.
Push Switch 2 Switch is ON. 1
Push Switch 3 Switch is ON. 1
019 Rocking Guide Close Guide is closed. 1 2-Bin Finisher
Sensor (FS600),
Shutter Close Sensor Shutter is closed. 1 2-Bin Saddle-Stitch
Front Door Sensor Front Door is open. 0 Finisher (FS605), and
1-Bin Saddle-Stitch
Tray Danger Area Sensor Tray Danger Area 0
Finisher (FS355A).
Upper Limit Detection Upper Limit 1
Sensor
Saddle Unit Sensor Saddle Unit is detected. 1
Front Door Open Sensor Front Door is open. 0
Joint Detect Sensor Finisher Unit is detected. 1
B position.
Platen
Size Sensor A Original detected on the 1 Z
A position. Y
X
Size Sensor Z Original detected on the 1
Front Side
Z position.
Size Sensor Y Original detected on the 1
Y position.
Size Sensor X Original detected on the 1
X position.
021 ADF/Platen Cover Angle ADF/Platen Cover is 1
Sensor open more than 30°
angle.
ADF/Platen Cover Open ADF/Platen Cover is 1
Sensor open.
Home Position Sensor Home position is 1
detected.
+24V Line Error Detecting +24V Line is OFF. 1
Signal
022- Not Used
029
030 ADF B1 Sensor Original is detected. 1
ADF B2 Sensor Original is detected. 1
ADF B3 Sensor Original is detected. 1
ADF Inverting Sensor Original is detected. 1
ADF Paper Exit Detection Original is detected. 1
Sensor
ADF Cover Open Cover is open. 1
Detection Sensor
ADF Detection Sensor ADF is not detected. 1
031 ADF Original Sensor Original is detected. 1
ADF Original Width Sensor Sensor is activated. 1
1
ADF Original Width Sensor Sensor is activated. 1
2
ADF Original Length Sensor is activated. 1
Sensor 1
ADF Original Length Sensor is activated. 1
Sensor 2
032- Not Used
039
Ver. 1.1
193 DEC 2006
DP-8060/8045/8035
2. Output Check
Press the "Start" key to begin, and press the "Stop" key to reset.
Ver. 1.1
195 DEC 2006
DP-8060/8045/8035
F4 Mode (Output Check)
No. Item Function Remark
101 ADU Paper Feed Clutch When CN716-4 signal level changes 1 minute
to 0V from +24V, clutch operates.
102 Inverting Motor Rotating In Inverting motor rotates in the forward
Forward Direction direction.
103 Inverting Motor Rotating In Inverting motor rotates in the reverse
Reverse Direction direction.
104 Paper Guide Solenoid ON When CN763-10 signal level
changes to 0V from +24V, clutch
turns ON for Straight Paper Exit.
105 Paper Guide Solenoid OFF When CN763-12 signal level
changes to 0V from +24V, clutch
turns OFF for Inverting Paper Exit.
106 Roller Solenoid ON When CN763-7 signal level changes
to 0V from +24V, clutch turns ON for
the Inverting Roller turning OFF.
107 Roller Solenoid OFF When CN763-9 signal level changes
to 0V from +24V, clutch turns OFF for
the Inverting Roller turning ON.
108 Saddle Paper Feed Unit Test Feed Motor turns ON. 2-Bin Saddle-Stitch
Finisher (FS605) Only.
109 Tray Elevator Unit Test 1 Tray moves to Upward direction. 2-Bin Finisher (FS600),
110 Tray Elevator Unit Test 2 Tray moves to Home Position. 2-Bin Saddle-Stitch
Finisher (FS605), and
2-Bin Finisher (FS330).
111 Paper Feed Unit Test Feed Motor turns ON.
112 Paper Exit Unit Test Feed Motor turns ON. 2-Bin Finisher (FS600),
2-Bin Saddle-Stitch
Finisher (FS605), and
1-Bin Saddle-Stitch
Finisher (FS355A).
113 Collation Unit Test Collation Plates turns ON.
114 Stapler Unit Test Stapler turns ON.
115 Stapler Unit Move Test Stapler Unit moves. 2-Bin Finisher (FS600),
and 2-Bin Saddle-Stitch
Finisher (FS605).
116 Rocking Unit Test Guide turns ON. 2-Bin Finisher (FS600),
117 Shutter Unit Open Test Shutter unit is opened. 2-Bin Saddle-Stitch
Finisher (FS605), and
2-Bin Finisher (FS330).
118 Not Used
119 Shutter Unit Close Test Shutter unit is closed. 2-Bin Finisher (FS600),
and 2-Bin Saddle-Stitch
Finisher (FS605).
120 Lamp When CN756-8 signal level changes
to 0V from +24V, Lamp operates for
4 seconds.
121- Not Used
159
160 ADF Paper Feed Motor Rotating ADF paper feed motor rotates at
(67% of rotating speed) 67% of rotating speed.
Ver. 1.1
197 DEC 2006
DP-8060/8045/8035
4.1.4. F5 Mode: Function Parameters (For Copier)
Set the machine to Service Mode, and press "5" key on the Keypad.
↓
Press the "Start" key.
↓
Select the desired code number on the Touch Panel display.
↓
If you wish to select another code number, scroll the menu with the arrow buttons.
↓
Select the desired function on the Touch Panel display, and select the "OK" button.
↓
When the "C (Clear)" key is pressed, the selected code input will not be utilized.
↓
Press "Function", and "C (Clear)" keys simultaneously to exit the service mode.
↓
Reboot the machine after setting the parameter(s) to activate the setting(s).
F5 Mode
No. Item Function Default Setting
00 Country Version 0 : Japan Country Dependent
1 : USA/CAN
2 : Europe
3 : Other
01 Frequency Desired 0 : Auto 2 (for USA / Canada)
1 : 50 Hz
2 : 60Hz 1 (for Europe)
02 Not Used
03 LSU Startup Speed 0 : Low 1
1 : Full
04 LSU Off Timer 1 : 5 sec. 3
2 : 10 sec.
3 : 15 sec.
4 : 20 sec.
6 : 30 sec.
8 : 40 sec.
10 : 50 sec.
12 : 60 sec.
05 Not Used
06 Job Tracking Server 0 : No 0
1 : Yes
Ver. 1.1
199 DEC 2006
DP-8060/8045/8035
F5 Mode
No. Item Function Default Setting
16 Paper Size Tray 3 0 : None 0
1 : A3
2 : B4 Note:
3 : A4 The available
4 : A4R paper size is
5 : B5 dependent on the
6 : B5R destination's
7 : A5 specification.
9 : 8 x 13
10 : 8.5 x 13
11 : LEDGER
12 : LEGAL
13 : LETTER
14 : LETTER R
15 : INVOICE
17 Paper Size Tray 4 Same as F5-16 Same as F5-16
18 Paper Size L (LCT) 3 : A4 13 (for USA / Canada)
5 : B5
12 : LEGAL 3 (for Europe)
13 : LETTER
14 : LETTER R
19 Not Used
20 ADF 0 : No 1
1 : Auto
21 Finisher 0 : No 1
1 : Auto
22 System Console 0 : No 1
1 : Auto
23 LCT 0 : No 1
1 : Auto
24 QUANTUM TDC Level Adj. 0 : No 1
(Factory Use Only) 1 : Low
2 : Medium
3 : High
25 Digital QUANTUM 0 : Off 1
1 : On
26 2-Sided Unit 0 : No 1
1 : Auto
27 COPY Output Bin 0 : Upper 0
(For DA-FS600/605 only) 1 : Bottom
28 PRINTER Output Bin Same as F5-27 1
(For DA-FS600/605 only)
29 FAX/EMAIL Output Bin Same as F5-27 1
(For DA-FS600/605 only)
30- Not Used
31
32 Job Build And SADF Mode 0 : No 1
1 : Yes
33 Not Used
34 Multi Size Feed Default 0 : Off 0
1 : On
Ver. 1.1
201 DEC 2006
DP-8060/8045/8035
F5 Mode
No. Item Function Default Setting
53 2-Sided Auto Shift 0 : No 0
1 : Auto Sft
54 Margin Reduction 0 : No 0
1 : Yes
55 Margin Value Default 0 : 5 mm 1
1 : 10 mm
2 : 15 mm
3 : 20 mm
56 Edge Value Default 0 : 5 mm 0
1 : 10 mm
2 : 15 mm
3 : 20 mm
57 Book Value Default 0 : 15 mm 1
1 : 20 mm
2 : 25 mm
3 : 30 mm
58 Oper. Waste Toner Alarm 0 : Stop 2
1:3K
2:5K
3:8K
4 : 10 K
59 Oper. Add Toner Alarm 0 : Stop 0
1 : Continue
60 Auto Tray Selection 0 : No 1
1 : Yes
61- Not Used
62
63 U13 Clear 0 : Any Keys 0
1 : Func + 1
64 Dept. Counter (SCANNER) 0 : Yes 0
1 : No
65 Dept. Counter (PRINTER) 0 : Yes 0
1 : No
66 Interleaving Default 0 : Blank 0
1 : Copy
67 Page Insertion Default 0 : Blank 0
1 : Copy
68 Cover Mode Default 0 : F, Blank 0
1 : F, Copy
2 : FB, Blank
3 : FB, Copy
69 Reduce N in 1 Space 0 : No 0
1 : Yes
Ver. 1.1
203 DEC 2006
DP-8060/8045/8035
F5 Mode
No. Item Function Default Setting
83 Digital Skyshot Mode 0 : No 1
1 : Freeshp
2 : Parallel
84 Paper Tray Priority 0:L>S>C>B 0
1 : C >S > L > B
2:L>C>S>B
85 Side Void Setting (ADF) 0 : None 0
1 : Yes
86 Not Used
87 PM Cycle (ADF) 0 : No 0
3 : 120 K
4 : 240 K
88 Not Used
89 LAN Speed/Duplex 0 : Auto 0
1 : 10 Half
2 : 10 Full
3 : 100 Half
4 : 100 Full
90 TCH Panel Beep Sound 0 : Off 1
1 : Soft
2 : Loud
91 M1, Size Set the default size for Manual Skyshot 70 x 160
92 M2, Size Mode, M1, and M2. 95 x 220
93- Not Used
94
95
96
97 (Factory Use Only)
98
99
Set the machine to Service Mode, and press "6" key on the Keypad.
↓
Press the "Start" key.
↓
Select the desired code number on the Touch Panel display.
↓
If you wish to select another code number, scroll the menu with the arrow buttons.
↓
Select the desired function on the Touch Panel display, and select the "OK" button.
↓
When the "C (Clear)" key is pressed, the selected code input will not be utilized.
↓
Press "Function", and "C (Clear)" keys simultaneously to exit the service mode.
↓
Reboot the machine after setting the parameter(s) to activate the setting(s).
Note:
The Factory Setting may differ for each model.
F6 Mode
Setting
No. Item Remarks
Range
00 Adj 100% Side-Side Read Adjustment of ratio for vertical position when -9 - +9 0.1%
scan is made.
01 Adj 100% Lead-Tail Read Adjustment of ratio for parallel position when -9 - +9 0.1%
scan is made.
02 100% Selection Adjustment from 99.1% to 100.9% -9 - +9 0.1%
03 Original Registration Adjustment of platen original registration -30 - +30
detection timing. 0.2mm
04 Printer Registration Delay time is adjusted from registration roller -50 - +50
clutch ON. 0.5mm
05 Main Motor Speed Adjustment of Main Motor speed. -10 - +10
0.1%
06 Polygon Motor Speed Adjustment Polygon Motor speed. -99 - +99
0.1%
07 Registration Void Registration void should be adjusted. 0 - +99
0.5mm
08 Trail Edge Read Timing Adjustment of trail edge void. -9 - 0
0.5mm
09 Trail Edge Print Timing Adjustment of trail edge void. -9 - +15
0.5mm
10 Side Adjust (Bypass) Adjustment of LSU side-side (Sheet Bypass). -8 - +7
0.5mm
11 Side Adjust (Tray 1) Adjustment of LSU side-side (1st Tray). -8 - +7
0.5mm
12 Side Adjust (Tray 2) Adjustment of LSU side-side (2nd Tray). -8 - +7
0.5mm
13 Side Adjust (Tray 3) Adjustment of LSU side-side (3rd Tray). -8 - +7
0.5mm
Ver. 1.1
205 DEC 2006
DP-8060/8045/8035
F6 Mode
Setting
No. Item Remarks
Range
14 Side Adjust (Tray 4) Adjustment of LSU side-side (4th Tray). -8 - +7
0.5mm
15 Side Adjust (LCT) Adjustment of LSU side-side (LCT). -8 - +7
0.5mm
16 Side Adjust (ADU) Adjustment of LSU side-side (ADU). -8 - +7
0.5mm
17 Standard Grid Voltage Adjustment of Grid standard voltage. -92 - +61
3.27V
18 Standard Laser Power Laser power compensation adjustment. -56 - +65
19 Std Bias DC Voltage Adjustment of bias standard voltage. -77 - 76
3.92V
20 Print Contrast Adjust Halftone adjustment, Print density -7 - +7
for Photo Mode.
(-) : Darker.
(+) : Lighter.
21 TDC Gain Voltage Adjustment of toner density sensor gain -86 - +40
voltage. 0.033V
22 (Factory Use Only) QUANTUM parameter 1
23 (Factory Use Only) QUANTUM parameter 2
24 Std Bias AC Voltage AC Bias standard voltage adjustment -10 - +10
(Factory Use Only) 20V
25 Bias Duty Ratio Bias duty ratio adjustment -5 - +5 1%
(Factory Use Only)
26 TDC Judgement Level Adjustment of toner supply starting judgement -26 - +26
voltage level. 19.5mV
27 Bias Frequency AC Bias frequency adjustment -2 - +2
(Factory Use Only) 1KHz
28 QUANTUM White Density Adjustment of standard white density level. -99 - +99
(Factory Use Only) (Should not be adjusted in the field, and must
be set to "0")
29 QUANTUM Black Density Adjustment of standard black density level. -99 - +99
(Factory Use Only) (Should not be adjusted in the field, and must
be set to "0")
30 2-Level Laser Power Adj. Laser power compensation adjustment in 2 -56 - +25
value mode.
31 Fuser Temperature Adjustment of fuser temperature. -15 - +15
0.833°C
32 Fuser Edge Temperature Temperature compensation for edges -15 - +15
0.833°C
33 TDC Max. Read Only Set by Digital QUANTUM (QUARC) control Read only
34 TDC Min. Read Only Set by Digital QUANTUM (QUARC) control Read only
35 TDC Avg. Read Only Set by Digital QUANTUM (QUARC) control Read only
36 Paper Loop (Tray 1) Individual Fine Adjustment for Tray 1 -99 - +99
37 Toner Save Mode Lvl Adj. Adjustment of threshold level. -255 - +255
38 ID Standard Voltage Adjustment of judgement standard voltage. -35 - +35
(Factory Use Only)
39 LSU Unit PWM Adjust 2 Adjustment of PWM value of LSU. -99 - +99
Ver. 1.1
207 DEC 2006
DP-8060/8045/8035
F6 Mode
Setting
No. Item Remarks
Range
67 ADF Image Density Compensation of ADF image density. -99 - +99
68 Paper Loop (Tray 3) Individual Fine Adjustment for Tray 3 -99 - +99
69 Stamp Position Adjust Adjustment of verification stamp position. -50 - +50
0.3mm
70-74 Not Used
75 Adj Read AD Enable Adjustment of read timing. -2 - +2
(Factory Use Only)
76 Adj Read LSI Sampling Adjustment of read timing. 0 - +3
(Factory Use Only)
77 Adj Read LVDS Clock Adjustment of read timing. 0 - +3
(Factory Use Only)
78 Paper Loop (Tray 4) Individual Fine Adjustment for Tray 4 -99 - +99
79 MTF (Modulation Transfer Adjustment of Scanning Sharpness by digital -2 - +2
Function) Adjust image processing for Text /Photo Copy Mode.
80 QUANTUM Exposure Volt. Set by Digital QUANTUM (QUARC) control -56 - +65
81 QUANTUM Bias DC Volt. Set by Digital QUANTUM (QUARC) control -77 - +76
3.92V
82 QUANTUM Charge Voltage Set by Digital QUANTUM (QUARC) control -92 - +61
3.27V
83 Temperature Sensr Value Value of Temperature sensor. 0 - 255
84 Humidty Sensor Value Value of Humidity Sensor. 0 - 255
85 (Factory Use Only)
86 ADF Reverse Stop Posi. Adjustment of ADF reverse stop position. -99 - +99
0.3mm
87 ADF Exhaust Stop Posi. Adjustment of ADF exit stop position -99 - +99
0.3mm
88 ADF Feed Regist.1-Sided Adjustment of ADF pick up for 1-sided. -99 - +99
0.3mm
89 ADF Feed Regist.2-Sided Adjustment of ADF pick up for 2-sided. -99 - +99
0.3mm
90 ADF Read Main Scan Pos. Adjustment of ADF horizontal image read -99 - +99
start position. 0.05mm
91 Original Lead Edge ADF Adjustment of original detection timing. -99 - +99
0.3mm
92 Original Trail Edge ADF Adjustment of trail edge detection timing. -127 - 127
0.3mm
93 ADF 100% Image 1-Sided Adjustment of magnification for 1-sided. -9 - +9
0.1%
94 ADF 100% Image 2-Sided Adjustment of magnification for 2-sided. -9 - +9
0.1%
95 Exp. Volt. Adjustment of LSU Laser Power. -56 - +65
(QUANTUM is OFF)
96 Charge V. Adjustment of Charge Voltage. -95 - +61
(QUANTUM is OFF) 3.27V
97 Bias DC V. Adjustment of Bias Voltage. -77 - +76
(QUANTUM is OFF) 3.92V
98 Paper Loop (LCT) Individual Fine Adjustment for LCT. -99 - +99
99 F5/F6 Initialization Initialize F5/F6 parameter settings.
Set the machine to Service Mode, and press "7" key on the Keypad.
↓
Press the "Start" key.
↓
Select the desired code number on the Touch Panel display.
↓
If you wish to select another code number, scroll the menu with the arrow buttons.
↓
Select the desired function on the Touch Panel display, and select the "OK" button.
↓
When the "C (Clear)" key is pressed, the selected code input will not be utilized.
↓
Press "Function", and "C (Clear)" keys simultaneously to exit the service mode.
F7 Mode
Service
Item Remarks
Mode
F7 Electronic 00 List Print
Counter 01 Application Password Password for Firmware Version update,
Print job queue functions, and various
PC application operations.
02 Maintenance 00 Total Count Total count for all copies / prints.
Count 01 PM Count Preventive Maintenance count.
02 Scanner PM Count PM count for scanner readings.
03 ADF Count PM count of originals fed through the
ADF.
04 Not Used
05 OPC Drum Count PM count of recording paper fed
through the OPC Drum.
06 Process Unit Count PM count of recording paper fed
through the Process Unit.
07 ADF PM Count PM count of recording paper fed
through the Automatic Duplex Unit.
08 Fuser Web Count PM Count for Fuser Web.
09 Developer Count PM Count for Developer.
10 Corona Cleaning Count for Corona Cleaner.
Count
11 Avg. Print/Drum Rise Average Print Count for OPC Drum.
Up
12 Total OPC Rotation Rotation Time for OPC Drum.
Time
13 Avg. Min / Drum Rise Average Rotation Time for OPC Drum.
Up
14 Developer Using Time Count for Developer.
Ver. 1.1
209 DEC 2006
DP-8060/8045/8035
F7 Mode
Service
Item Remarks
Mode
F7 Electronic 03 Paper Feed 00 Sheet Bypass Count Total count of paper fed from the sheet
Counter Count bypass.
01 1st Paper Tray Count Total count of paper fed from the 1st
paper tray.
02 2nd Paper Tray Count Total count of paper fed from the 2nd
paper tray.
03 3rd Paper Tray Count Total count of paper fed from the 3rd
paper tray.
04 4th Paper Tray Count Total count of paper fed from the 4th
paper tray.
05 LCT Tray Count Total count of paper fed from the LCT.
06 2-Sided Count Total count of 2-sided Print.
07 A4 / Letter Count Total count of A4 / Letter Print.
08 A4-R / Letter-R Count Total count of A4-R / Letter-R Print.
09 A3 / Ledger Count Total count of A3 / Ledger Print.
10 B4 / Legal Count Total count of B4 / Legal Print.
04 Scanner 00 ADF Count Total count of originals fed through the
Count ADF.
01 ADF Read Count Total count of originals scanned through
the ADF.
02 Scanner Count Total count of scanning operations.
03 Scanner Read Count Total count of scanner readings.
05 Copy Count 00 Copy Print Count Total count of copies printed.
01 Copy Scan Count Total count of copies scanned.
06 PC Count 00 PC Print Count Total count printed from PC.
01 PC Scan Count Total count scanned to PC.
07 Fax Count 00 Fax Transmit Count Total count of Fax transmitted.
01 Fax Receive Count Total count of Fax received.
02 Fax Print Count Total count of Fax printed.
08 All Counter Clear All counters are cleared.
09 Service Mode Password Password for Service Mode.
Set the machine to Service Mode, and press "8" key on the Keypad.
↓
Press the "Start" key.
↓
Select the desired code number on the Touch Panel display.
↓
If you wish to select another code number, scroll the menu with the arrow buttons.
↓
Select the desired function on the Touch Panel display, and select the "OK" button.
↓
When the "C (Clear)" key is pressed, the selected code input will not be utilized.
↓
Press "Function", and "C (Clear)" keys simultaneously to exit the service mode.
F8 Mode
No. Item Remarks
00 Exposure Lamp replacement When replacing the exposure lamp.
Procedure:
a) Press the Start key to move the exposure lamp
to the position (approx. 250 mm from the optics
home position) where it can be replaced.
b) To return the optical system to the home position,
press the Clear key.*
01-05 Not Used
06 Error Log Print/View a) Each time the arrow button is pressed, the
machine errors, or the paper jam codes stored in
memory are displayed, beginning with the oldest
code.
Note:
Only the 30 most recent codes are displayed.
07 Error Log Clear a) Press the Reset key.
A Message "Error code can be cleared with the
Start key" is displayed on the LCD.*
b) Press the Start key.
08 (Factory Use Only) Lock operation for Scanner Unit.
09 Toner Density Adj. Adjustment operation of Toner Density.
10 Drum Charge Checking Adjustment operation of Drum Charge.
11-12 Not Used
13 Black Density Reference Adjustment operation of Black Density sensor.
(Factory Use Only)
14 OPC Counter Reset Resets the OPC Counter.
15 QUANTUM Pattern Print out the QUANTUM Test Pattern.
(Factory Use Only)
16 Not Used
17 LSU PWM Pattern 1 Print out the Test Pattern 1.
(Factory Use Only)
18 LSU PWM Pattern 2 Print out the Test Pattern 2.
(Factory Use Only)
Ver. 1.1
211 DEC 2006
DP-8060/8045/8035
F8 Mode
No. Item Remarks
19 Move Mirror To Lock a) Press the Start key to move the mirror unit to the
locked position for transporting the copier.
b) When the mirror unit is locked, the machine will
not accept any numerical key input.
Note:
The locking operation is automatically reset when
the Power switch is turned ON again.
20 TDC Sensor Output Adj. Adjustment of TDC sensor.
21 Not Used
22 LSU PWM Pattern 3 Print out the Test Pattern 3.
(Factory Use Only)
23 LSU PWM Pattern 4 Print out the Test Pattern 4.
(Factory Use Only)
24-46 Not Used
47 ADF Continuous Test Press Start key to begin.
48 Platen Continuous Test Press Start key to begin.
49-54 Not Used
Set the machine to Service Mode, and press "9" key on the Keypad.
↓
Press the "Start" key.
↓
Select the desired code number on the Touch Panel display.
↓
If you wish to select another code number, scroll the menu with the arrow buttons.
↓
Select the desired function on the Touch Panel display, and select the "OK" button.
↓
When the "C (Clear)" key is pressed, the selected code input will not be utilized.
↓
Press "Function", and "C (Clear)" keys simultaneously to exit the service mode.
F9 Mode
Service
Item Remarks
Mode
F9 Unit 00 FAX Service Mode
Maintenance 01 Service Alert Tel # Displays the contact number when a
machine malfunction occurs.
02 Firmware 00 SC Displays the firmware version for SC.
Version 01 SC Boot Displays the firmware version for SC
Boot.
02 PNL Displays the firmware version for PNL.
03 SPC Displays the firmware version for SPC.
04 Finisher Displays the firmware version for
finisher.
05 FAX Modem Displays the firmware version for FAX
option 1.
06 Not Used
07 SC2 Displays the firmware version for Slot 1.
08 Not Used
~
11
12 Data Security Kit Displays the firmware version for Data
Security Kit.
03 Print 00 F5/F6 Parameters Prints the memory contents of the F5,
Device Info. and F6 modes.
01 Machine Information Prints the machine setup information list.
02 System Address Prints the system memory setting.
Info.
03 RAM Address Prints the RAM data dump list.
Information
04 RAM Edit 00 Relative Addr Setting Setting of Relative address.
Mode 01 Real Address Setting Setting of Real address.
05 Serial Number Registration of Serial Number for
Maintenance.
Clears by Shipment Set.
Ver. 1.1
213 DEC 2006
DP-8060/8045/8035
F9 Mode
Service
Item Remarks
Mode
F9 Unit 06 RAM 00 Parameter Initialize Resets the Fax, and Function
Maintenance Initialize parameters to default values.
Note:
Turn the Power Switch on the Left
Side of the machine to the OFF, and
back to the ON position to enable the
parameter settings.
01 All Job Clear Clears all Jobs stored in Flash Memory.
02 Not Used
03 Shipment Set Clears All Jobs, All Preset Data,
Parameter Initialize & Resets the
Counters (Fax).
04 LBP Fuser Reset Clears the LBP fuser error.
05 Dept. Counter Clear
07 Firmware 00 Update From Master Updates the firmware in the machine
Update Card with the Master Firmware Card.
01 Update From Parallel Updates the firmware in the machine
Port with the Parallel Port.
08 Program 00 Main Onboard F-ROM 4MB
Backup 01 Option 1 All Slot 1 FRM8 PCB 8MB
(Refer to 02 Option 1 A Slot 1 FRM8 PCB 4MB (a)
Sect. 2.6.)
03 Option 1 B Slot 1 FRM8 PCB 4MB (b)
04 Option 2 All Slot 2 FRM8 PCB 8MB
05 Option 2 A Slot 2 FRM8 PCB 4MB (a)
06 Option 2 B Slot 2 FRM8 PCB 4MB (b)
09 Update Program Card Creates a Master Firmware Card using
the Firmware Update Kit. A 4MB, or
8MB Flash Memory Card will be
required depending upon the model.
10 Program 00 From Card To Slot 1 Configuration for Program copy.
Copy 01 From Card To Slot 2
02 From Slot 1 To Card
03 From Slot 1 To Slot 2
04 From Slot 2 To Card
05 From Slot 2 To Slot 1
11 Parameter Backup Backup the Parameter.
12 Parameter Restore Restore the Parameter.
13 Page Memory Size Displays the page memory size (MB).
14 Sort Memory Size Displays the sort memory size (MB).
Ver. 1.1
215 DEC 2006
DP-8060/8045/8035
4.2.3. Fax Service Mode 1 (Function Parameter Setting)
Use the following procedure to change the function parameters.
Select the "01 Function Param. Setting" on the Touch Panel display.
↓
Select the desired code number on the Touch Panel display.
↓
If you wish to select another code number, scroll the menu with the arrow buttons.
↓
Select the desired function on the Touch Panel display, and select the "OK" button.
↓
Select the "OK" button 3 times.
↓
Press "Function", and "C (Clear)" keys simultaneously to exit the service mode.
Ver. 1.1
217 DEC 2006
DP-8060/8045/8035
Function Parameter Table
No. Parameter Selections Function
012 DTMF Level 00 = 0 dBm Selects the DTMF output level, 0 to -15 dBm in 1
~ dBm steps.
15 = -15 dBm
013 G3 RX EQL 1 = 0dB Selects the cable equalizer for G3 reception mode,
2 = 4dB 0dB, 4dB, 8dB, or 12dB.
3 = 8dB
4 = 12dB
014 G3 TX EQL 1 = 0dB Selects the cable equalizer for G3 transmission
2 = 4dB mode, 0dB, 4dB, 8dB, or 12dB.
3 = 8dB
4 = 12dB
015 Not Used
~
016
017 TX Start 1 = 2400 bps Selects the transmission modem start speed, 14400/
2 = 4800 bps 12000/TC9600/TC7200/9600/7200/4800/2400 bps.
3 = 7200 bps Note:
4 = 9600 bps This parameter is applicable only when
5 = TC7200 communicating with regular G3 machines. When
6 = TC9600 communicating with Super G3 (V.34) machines,
7 = 12000 bps use Parameter No. 32.
8 = 14400 bps
018 RX Start 1 = 2400 bps Selects the reception modem start speed, 14400/
2 = 4800 bps 12000/TC9600/TC7200/9600/7200/4800/2400 bps.
3 = 7200 bps Note:
4 = 9600 bps This parameter is applicable only when
5 = TC7200 communicating with regular G3 machines. When
6 = TC9600 communicating with Super G3 (V.34) machines,
7 = 12000 bps use Parameter No. 33.
8 = 14400 bps
019 ITU-T V.34 1 = Off Selects whether the ITU-T V.34 is Off, On, or Select.
2 = On Select: Select whether the ITU-T V.34 is Off, or On,
3 = Select when entering Phone Book Dialing
Numbers, or Manual Number Dialing.
020 ITU-T ECM 1 = Off (Invalid) Select the ECM mode.
2 = On (Valid)
021 EP Tone 1 = Off (without EP Tone) Selects whether to add the echo protect tone on V.29
2 = On (with EP Tone) mode.
(Used when Echo Suppression is disabled.)
On : Add
Off : Do not add
022 Signal Interval1 = 100 ms Selects the time interval between the receiving
2 = 200 ms signal, and the transmitting signal.
3 = 500 ms
023 TCF Check 1 = Normal (Short) Selects the TCF check interval Long/Short
2 = Long
024 CED Frequency 1 = 1080 Hz (non ITU-T) Selects the CED frequency 2100/1080 Hz
2 = 2100 Hz
025 Comm. Start-Up 1 = First Selects the communication start-up condition (XMT,
2 = Second and Polling).
(Used when Echo Suppression is disabled.)
Ver. 1.1
219 DEC 2006
DP-8060/8045/8035
Function Parameter Table
No. Parameter Selections Function
046 On-Hook Time 0 = 0 sec. Selects the on-hook time between sequential
~ communication calls in 1 second step intervals.
90 = 90 sec.
047 Response Wait 1 = 1 sec. Selects the waiting interval for the response after
Interval ~ completing the dialing.
90 = 90 sec.
20 ~ 150 sec.
(For France Only)
048 Not Used
~
049
050 Ring Detect 1 = Normal Selects the quality of ringer detection. Use if the line
Mode 2 = Rough signal is out of regulation, set to "Rough" so that the
unit may detect the ringing signals.
051 Not Used
052 Pulse Rate 1 = 10 pps Selects the dial pulse rate 10/20 pps.
2 = 20 pps
053 Not Used
~
054
055 Busy Tone 1 = Off Selects whether to detect the Busy Tone.
Check 2 = On
056 Dial Tone Check 1 = Off Selects whether to detect Dial Tone before dialing
(Except for USA, 2 = On the telephone number.
and Canada)
057 DC Loop Check 1 = Off Selects whether the unit checks the DC Loop during
(Except for USA, 2 = On communication.
and Canada)
058 Comm. JRNL + 1 = Off (without image) Selects whether the machine prints the COMM.
Image 2 = On (with image) Journal with image.
059 Confidential 1 = Off (does not print out) Selects whether the machine prints the Confidential
RCV Report 2 = On (prints out) RCV Report.
060 Version Indicates the Host software
version.
061 TX/RX/PRT/CPY 1 = Fax Transmit Count Displays the transmitted, received, total printed, and
2 = Fax Receive Count copied document count.
3 = Total Count
4 = Copy Print Count
062 Print Counter 1 = Off Selects whether to print in the Fax Parameter List,
2 = On the counter information that is displayed in the
Function Parameter No. 61.
063 Not Used
~
067
Ver. 1.1
221 DEC 2006
DP-8060/8045/8035
Function Parameter Table
No. Parameter Selections Function
082 JAM Length 1=1m Selects the maximum length of the original that can
2=2m be scanned.
083 Not Used
084 Line As No- 1 = Ring (ring) Selects whether to ring, or send a busy tone to the
Paper 2 = Busy (keep line busy) remote station when the recording paper runs out, or
the unit cannot receive because of any trouble.
085 Not Used
086 Reduction Fine 1 = Off Selects whether the resolution is preset to Fine,
2 = On when sending with reduction B4→A4.
087 Darker Level 0 = Lightest Contrast Selects the contrast level.
088 Normal Level ~ 0← →15
089 Lighter Level 15 = Darkest Contrast Lightest← →Darkest
090 Not Used
~
091
092 Smoothing 1 = Off Selects whether the smoothing function is available.
2 = On
093 Not Used
~
101
102 Original -30 Adjustment of original registration detection timing.
Registration ~
+30
103 Trail Edge Read -9 Adjustment of trail edge void.
Timing ~
0
104 Not Used
~
109
110 Mac Address Indicates the MAC Address.
111 Not Used
112 Insert EMAIL 1 = Off Selects whether the Text Template (email message)
TXT 2 = On is programmable, and added on all email sent in the
message body above the top line of text. (Up to 40
characters Programmed in the User Parameters.)
Note:
After enabling this feature, aside from entering
the text in the User Parameters, it also has to be
activated in each Auto Dial Number before it will
take effect. It does not work for Direct Dialed
Numbers.
113 Not Used
~
114
115 Time Zone 1 = Scroll Selects the setting method for Time Zone.
2 = Direct Scroll : Allows using "Scroll Keys" to scroll
through the Time Zone Table.
Direct : Allows you to input the Time Zone directly,
(*) key to be used as a switch between +/-.
To enable the Continuous Polling feature set Function Parameter No. 003 to "2:Station". The last
Program Key will be assigned with the "Store 4 Poll" Key name automatically, and cannot be
changed.
To prepare the document(s) to be polled, simply place the document(s) on the ADF, or Platen, and
then press the Program Key to store, or add the document(s) into a polled file.
(Note: If a regular polled file is stored in memory, the Program Key for Continuous Polling will not
be accepted.)
Note 2: Function Parameter No. 070 (Line Error)-Transmit condition of RTP/PIP, or RTN/PIN
Setting
Signal
1:128 2:256 3:512 4:1024 5:2048 6:Off
MCF/PIP 0-31 0-63 0-127 0-255 0-511 Always
RTP/PIP 32-63 64-127 128-255 256-511 512-1023 -
RTN/PIN 64-127 128-255 256-511 512-1023 1024-2047 -
Note 3: Function Parameter No. 071 (Total Error)-Transmit condition of RTP/PIP, or RTN/PIN
Setting
Signal
1:5% 2:10% 3:15% 4:20%
MCF/PIP 0-2 0-4 0-7 0-9
RTP/PIP 3-4 5-9 8-14 10-19
RTN/PIN 5- 10- 15- 20-
Note 4: The default setting of parameters depends on the country’s specifications, or regulations.
Print the Function Parameter List to confirm the default settings.
Ver. 1.1
223 DEC 2006
DP-8060/8045/8035
4.2.4. Fax Service Mode 3 (Printout of Lists, Reports, and Test Results)
From this Service Mode you can print the Function Parameter List, Page Memory Test, Printer Report, All
Document File, Protocol Trace, and the Toner Order Form.
4.2.4.1. Function Parameter List
A list of all Function Parameters can be printed by the following procedure.
Select the "03 Print Param. List/Report" on the Touch Panel display.
↓
Select the "01 Function Parameter List" on the Touch Panel display.
↓
Select the "YES” button to print Function Parameter List.
↓
Select the "OK" button 3 times.
↓
Press "Function", and "C (Clear)" keys simultaneously to exit the service mode.
************* -FUNCTION PARAMETER- ************* DATE MMM-dd-yyyy ***** TIME 12:07 ***P.01
030 CED & 300bps 75ms 080 Original Lead Edge ADF 0
031 RTC = EOL x 12 Off 081 Original Tail Edge ADF 0
032 V34 TX Start 33600bps 082 JAM Length 2 m
033 V34RX Start 33600bps 083 ----------
034 V34 TX SR 3429sr 084 Line As No-Paper Ring
035 V34 RX SR 3429sr 085 ----------
036 --------- 086 Reduction Fine On
037 Protocol Dislay Off 087 Darker Level 2
038 --------- 088 Normal Level 8
039 Flash Time 500ms 089 Lighter Level 14
Note:The power must be reset for the new parameter settings to take effect.
Note:
1. The contents of the Function Parameter List may vary depending on the country’s regulations.
2. “ * ” mark will be shown on the left side of number when setting was changed from default.
Ver. 1.1
225 DEC 2006
DP-8060/8045/8035
4.2.4.2. Page Memory Test
A test pattern prints out for checking the page memory (IC120, and IC121 on the SC PCB), and printer
mechanism using the following procedure.
Select the "03 Print Param. List/Report" on the Touch Panel display.
↓
Select the "03 Page Memory Test" on the Touch Panel display.
↓
Select the "YES" button to print a test pattern.
↓
Select the "OK" button 3 times.
↓
Press "Function", and "C (Clear)" keys simultaneously to exit the service mode.
Select the "03 Print Param. List/Report" on the Touch Panel display.
↓
Select the "04 Printer Report" on the Touch Panel display.
↓
Select the "YES" button to print a Printer Report.
↓
Select the "OK" button 3 times.
↓
Press "Function", and "C (Clear)" keys simultaneously to exit the service mode.
FIRMWARE VERSION
SC : DP-xxxx BAVxxxxxPU
PNL : AAVxxxxxPU
SPC : xxcpm Vxxxxx
DATA SECURITY KIT : Vxxxxx
TRANSMIT COUNTER : 1
RECEIVE COUNTER : 1350
COPY COUNTER : 5704
PRINT COUNTER : 16024
NO.DATE & TIME ERROR CODE RRROR COUNT NO.DATE & TIME ERROR CODE RRROR COUNT
--------------------------------------------------------------------------------------------
01.MMM-dd-yyyy 15:38 J00 00-00000016
02.MMM-dd-yyyy 10:48 J02 00-00000016
--------------------------------------------------------------------------------------------
-PANASONIC -
***** *******************- -*******-12345678901234567890-**************
Ver. 1.1
227 DEC 2006
DP-8060/8045/8035
4.2.4.4. All Document Files
Print the document files from the Flash Memory.
Select the "03 Print Param. List/Report" on the Touch Panel display.
↓
Select the "05 All Document Files" on the Touch Panel display.
↓
Select the "YES" button to print All Document Files.
↓
Select the "OK" button 3 times.
↓
Press "Function", and "C (Clear)" keys simultaneously to exit the service mode.
Select the "03 Print Param. List/Report" on the Touch Panel display.
↓
Select the "06 Protocol Trace" on the Touch Panel display.
↓
Select the "YES" button to print a Protocol Trace Report.
↓
Select the "OK" button 3 times.
↓
Press "Function", and "C (Clear)" keys simultaneously to exit the service mode.
*************** PROTOCOL LOG. REPORT ****************** DATE MMM-dd-yyyy ***** TIME 16:56 *******
STATUS : OK
MODE : ECM-TX (STANDARD)
SPEED : 28800bps 0MS/L (3429sr)
REMOTE CAPA. : NSF 00 00 79 34 12 00 82 00 09 03
10 18 00 0A 95 81 D0 80 91 D0
81 05
CSI 33 31 32 20 20 20 20 20 20 20
20 20 20 20 20 20 20 20 20 20
DIS 20 C2 FA C4 80 95 80 80 80 A0
80 80 80 01
LOCAL CAPA. : NSS 00 00 79 00 00 00 02 00 01 00
00 10 00 02 81 81 90 80 80 90
01
TSI 32 37 32 20 20 20 20 20 20 20
20 20 20 20 20 20 20 20 20 20
COMMAND LOG.
REMOTE : NSF CSI DIS CFR
LOCAL : TSI NSS PIX PPS-EOP
---------------------------------------------------------------------------------
REMOTE : MCF
LOCAL : DCN
---------------------------------------------------------------------------------
REMOTE :
LOCAL :
-PANASONIC -
****************************- -*************-12345678901234567890-***************
Ver. 1.1
229 DEC 2006
DP-8060/8045/8035
4.2.4.6. Toner Order Form
The Toner Order Form can be printed manually by the following procedure.
Select the "03 Print Param. List/Report" on the Touch Panel display.
↓
Select the "07 Toner Order Form" on the Touch Panel display.
↓
Select the "YES" button to print a Toner Order Form.
↓
Select the "OK" button 3 times.
↓
Press "Function", and "C (Clear)" keys simultaneously to exit the service mode.
*************************************
> TONER BOTTLE ORDER FORM <
*************************************
**** The toner supply in your machine is running low **** (1)
To order a replacement Bottle from your Authorized Dealer
Attention: Attention:
Quantity Required:
/ /
Print your name and title Signature & Date
Explanation of Contents
(1) Low Toner Message (Fixed) “The toner supply in your machine is running low”
(2) Toner Order Tel # Up to 36 digits
(3) Toner Order Fax # Up to 36 digits
(4) Customer ID Up to 16 characters (User Identification Code)
(5) Toner Bottle No. DQ-TU38R(PU) : DP-8060
DQ-TU37R(PB) : DP-8060
DQ-TU33R : DP-8045/8035
The order number(s) may differ depending on the Model, and the
Destination.
Ver. 1.1
231 DEC 2006
DP-8060/8045/8035
4.2.5. Fax Service Mode 4 (Modem Test)
4.2.5.1. Binary Signal
This Service Mode is used to check the binary signal output. Signals can be output to the line using the
following procedure.
Ver. 1.1
233 DEC 2006
DP-8060/8045/8035
4.2.5.3. DTMF Signal
This Service Mode is used to check the DTMF (Dual Tone Multi Frequency) signal output.
The DTMF signal can be generated using the following procedure.
Ver. 1.1
235 DEC 2006
DP-8060/8045/8035
4.2.6. Fax Service Mode 6 (RAM Initialization)
Initializes RAM, and restores the Function Parameters to their default values.
Note:
This operation should be performed when the unit is first installed.
Select the "08 Check & Call" on the Touch Panel display.
↓
Select the desired code number on the Touch Panel display.
(i.e. 01 Service Alert Fax #, input the telephone No., or for an email address, press the "Fax/Email"
Mode key, and input the email address.)
↓
Select the "OK" button.
↓
Select the "OK" button 3 times.
↓
Press "Function", and "C (Clear)" keys simultaneously to exit the service mode.
Note:
The Service, and Maintenance Alert Reports are managed in the same manner as the normal memory
transmission (Retry, Incomplete, File List, Display while it is transmitting, Journal).
Ver. 1.1
237 DEC 2006
DP-8060/8045/8035
Error Tx
Log Remarks
Code Report
Ex-xx O S Refer to the Mechanical Error Code (E Code) Table. (Sect. 3.1.3.)
E13 O Out of Toner.
Jxx O Refer to the Jam Error Code (J Code) Table. (Sect. 3.1.2.)
Uxx Refer to the User Error Code (U Code) Table. (Sect. 3.1.1.)
U13 O M Low Toner.
Note:
TX (Transmission) Report: S = Service Alert Report, M = Maintenance Alert Report
****************************
> SERVICE ALERT REPORT <
****************************
LAST PRINT ERROR : MMM-dd-yyyy 20:07 E04-01 00-00000013
(5) SERIAL NUMBER : 01234567890
(1) CUSTOMER ID : ABC COMPANY
(2) FIRMWARE VERSION
SC : BAV00008PU
PNL : AAT00001PU
SPC : 60cpm T400000
DATA SECURITY KIT : V10101
(3) COUNTER INFORMATION:
CURRENT PM CYCLE CURRENT
F7-02 Total Count : 13 240000 LCT Tray Count : 0
PM Count : 13 (------) 2-Sided Count : 0
Scanner PM Count : 9 (------) A4/LETTER Count : 3
ADF Count : 1 ------ A4-R/LETTER-R Count : 10
OPC Drum Count : 13 ------ A3/LEDGER Count : 0
Process Unit Count : 13 (------) B4/LEGAL Count : 0
ADF PM Count : 1
Fuser Web Count : 240986 F7-04 ADF Count : 1
Developer Count : 13 ADF Read Count : 1
Corona Cleaning Count : 13 Scanner Count : 9
Avg Print/Drum Rise Up : 1.00 Scanner Read Count : 9
Total OPC Rotation Time : 0.03
Avg Min/Drum Rise Up : 0.01 F7-05 Copy Print Count : 3
Developer Using Time : 6321 Copy Scan Count : 4
NO. DATE & TIME ERROR CODE ERROR COUNT | NO. DATE & TIME ERROR CODE ERROR COUNT
-------------------------------------------------------------------------------------------
01 MMM-dd-yyyy 20:07 E04-01 00-00000013 |
02 MMM-dd-yyyy 20:04 E04-01 00-00000013 |
|
|
|
|
|
|
|
|
|
|
|
-------------------------------------------------------------------------------------------
-LOGO PANASONIC -
***** *********************** -CHARACTER ID - ***** -31415926535897932384-*********
Explanation of Contents
(1) Customer ID
(2) Firmware Version
(3) Counter Information
(4) Print Error Last 30 records (Latest on top)
(5) Serial Number
Ver. 1.1
239 DEC 2006
DP-8060/8045/8035
4.2.7.4. MAINTENANCE ALERT REPORT FORMAT
****************************
> MAINTENANCE ALERT REPORT <
****************************
-LOGO PANASONIC -
Explanation of Contents
*************************************
> TONER BOTTLE ORDER FORM <
*************************************
**** The toner supply in your machine is running low **** (1)
To order a replacement Bottle from your Authorized Dealer
Attention: Attention:
Quantity Required:
/ /
Print your name and title Signature & Date
Explanation of Contents
(1) Low Toner Message (Fixed) “The toner supply in your machine is running low”
(2) Toner Order Tel # Up to 36 digits
(3) Toner Order Fax # Up to 36 digits
(4) Customer ID Up to 16 characters (User Identification Code)
(5) Toner Bottle No. DQ-TU38R(PU) : DP-8060
DQ-TU37R(PB) : DP-8060
DQ-TU33R : DP-8045/8035
The order number(s) may differ depending on the Model, and the
Destination.
Ver. 1.1
241 DEC 2006
DP-8060/8045/8035
4.2.7.6. CALL COUNTER REPORT
*****************************************************************
> SCHEDULED REPORT - CALL COUNTER HAS REACHED PRE-SET VALUE <
*****************************************************************
LAST PRINT ERROR : MMM-dd-yyyy 20:07 E04-01 00-00000013
(5) SERIAL NUMBER : 01234567890
(1) CUSTOMER ID : ABC COMPANY
(2) FIRMWARE VERSION
SC : BAV00008PU
PNL : AAT00001PU
SPC : 60cpm T400000
DATA SECURITY KIT : V10101
(3) COUNTER INFORMATION:
CURRENT PM CYCLE CURRENT
F7-02 Total Count : 13 240000 4th Paper Tray Count : 0
PM Count : 13 (------) LCT Tray Count : 0
Scanner PM Count : 9 (------) 2-Sided Count : 0
ADF Count : 1 ------ A4/LETTER Count : 3
OPC Drum Count : 13 ------ A4-R/LETTER-R Count : 10
Process Unit Count : 13 (------) A3/LEDGER Count : 0
ADF PM Count : 1 B4/LEGAL Count : 0
Fuser Web Count : 240986
Developer Count : 13 F7-04 ADF Count : 1
Corona Cleaning Count : 13 ADF Read Count : 1
Avg Print/Drum Rise Up : 1.00 Scanner Count : 9
Total OPC Rotation Time : 0.03 Scanner Read Count : 9
Avg Min/Drum Rise Up : 0.01
Developer Using Time : 6321 F7-05 Copy Print Count : 3
Copy Scan Count : 4
F7-03 Sheet Bypass Count : 0
1st Paper Tray Count : 3 F7-06 PC Print Count : 0
2nd Paper Tray Count : 10 PC Scan Count : 6
3rd Paper Tray Count : 0
F7-07 FAX Transmit Count : 0
Call Counter Pre-Set Value : 14000 FAX Receive Count : 0
(4) PRINT ERROR: FAX Print Count : 0
NO. DATE & TIME ERROR CODE ERROR COUNT | NO. DATE & TIME ERROR CODE ERROR COUNT
-------------------------------------------------------------------------------------------
01 MMM-dd-yyyy 20:07 E04-01 00-00000013 |
02 MMM-dd-yyyy 20:04 E04-01 00-00000013 |
|
|
|
|
|
|
|
|
|
-------------------------------------------------------------------------------------------
-LOGO PANASONIC -
***** *********************** -CHARACTER ID - ***** -31415926535897932384-********
Explanation of Contents
(1) Customer ID
(2) Firmware Version
(3) Counter Information
(4) Call Counter Pre-Set Value
(5) Serial Number
Note:
If the File is NOT on the designated machine, it has failed.
Select the "OK" button 3 times.
↓
Press "Function", and "C (Clear)" keys simultaneously to exit the service mode.
Ver. 1.1
243 DEC 2006
DP-8060/8045/8035
244
Ver. 1.1 DEC 2006
DP-8060/8045/8035
245
Ver. 1.1 DEC 2006
DP-8060/8045/8035
246
Ver. 1.1 DEC 2006
DP-8060/8045/8035
A B C D E
P4 N6
120
M6
S6 1
113
Fig. 4
3302 112 S6
S6 115
X5
3
S6 135
110 Fig. 12
S6
116
109
111 135
S6 S6 108 127
4
136 117 M9 134
S6
Y19
104
126
131 5
S6 118
137
S6
S6
6
S6
107 104
106
103 X5
124
7
125 121
124
J7 101
104 105 125
Y19
104 122
128
8
123 Fig. 1 Cover Assembly (1/2)
247
Ver. 1.1 DEC 2006
DP-8060/8045/8035
Cover Assembly
248
Ver. 1.1 DEC 2006
DP-8060/8045/8035
A B C D E
205 1
S6
213
219
X5
J6
207
Y19 2
210
209
219
219 J6
3
J6 212 207
219
X8
207
210 J6
Y19 207
4
219
206
219
216 5
211
X8
X8
214
204 6
X5 217
218 215
X5
X8 214
202 7
220
203
201
8
Fig. 2 Cover Assembly (2/2)
249
Ver. 1.1 DEC 2006
DP-8060/8045/8035
250
Ver. 1.1 DEC 2006
DP-8060/8045/8035
A B C D E
330
319 331 1
322
304
2
327
To
To C 305
A
328
3
333 307
335
309
To
310
D 311 312 308 From
P5 B
342
H4 4
8527 314
313
P5 316
318 326
317
5
341
325
303
324 340 6
340
8503
8526
8526
334
From 329 7
A
From
D From 332 323
C To
8527 B
X8
338
339 X8
8
Fig. 3 Control Panel Unit
251
Ver. 1.1 DEC 2006
DP-8060/8045/8035
252
Ver. 1.1 DEC 2006
DP-8060/8045/8035
A B C D E
330
319 331 1
322
304
2
327
To
To C 305
A
328
3
333 307
335
309
To
310
D 311 312 308 From
P5 B
342
H4 4
8527 314
313
P5 316
318 326
317
5
341
325
303
324 340 6
340
8503
8526
8526
334
From 329 7
A
From
D From 332 323
C To
8527 B
X8
338
339 X8
8
Fig. 3 Control Panel Unit
253
Ver. 1.1 DEC 2006
DP-8060/8045/8035
254
Ver. 1.1 DEC 2006
DP-8060/8045/8035
A B C D E
403 425
406
402
8621 1
405
404 8621
401
401
X5 410
X8
8621 2
Y28 401
408
402
409 8621 411
Y1
412
401
407
411 3
X8 412
413
415
414
X8
416 5
Y42 6
422
X8 418
417 7
Fig. 5-11
426
H5 417
8
Fig. 4 Inverting Automatic Document Feeder (1/8)
255
Ver. 1.1 DEC 2006
DP-8060/8045/8035
256
Ver. 1.1 DEC 2006
DP-8060/8045/8035
A B C D E
532
1002 539
510 1
H6 H7
511
505 Y43 513
509
533
506 H7
X8 516
538 507 Y43
2
508 515
517
501 540 514
502
530 X8 3
516 518
515
X8
Y43
519 X8
8622 523
541 705
541 513 522 X5 4
401
523 534
401 541 537
705 X5 X8
X5 541 521
X8
542 8622
X8 5
541 525
531 X8
535
526
1122 524 527
1122
6
528
529
X5
Fig. 6-11 8
Fig. 5 Inverting Automatic Document Feeder (2/8)
257
Ver. 1.1 DEC 2006
DP-8060/8045/8035
258
Ver. 1.1 DEC 2006
DP-8060/8045/8035
A B C D E
629
X8 602
628
601 626 1
603 626
605
629
605
X8
606
610 2
H6
604 609
631 539
630 608
607 615
613
612 X5
611 3
H9 614
639 8627
633
X5
616
X8 H6 4
624 625
623 642 Y26
J2 627
X5 634 X5 H7 X5 541
Y24 617
638
643 Y26
H7 618 5
S6 622
X5 641
619
636 637
614
H7 621
632
H9
616
Y26 6
635 641
Y26
8627
541
Fig.7-11 8
Fig. 6 Inverting Automatic Document Feeder (3/8)
259
Ver. 1.1 DEC 2006
DP-8060/8045/8035
260
Ver. 1.1 DEC 2006
DP-8060/8045/8035
A B C D E
707
706 X5
706 8623
705 1
707
8623
401 705 401
401
706 X5
8623 705 707 708
X5
541
X5
2
730
709 713 731
X5 727 X5 H6
X5
715 3
X5 541 710
K7 X5
401
6
8625
Fig. 8-11
721 X5
8
Fig. 7 Inverting Automatic Document Feeder (4/8)
261
Ver. 1.1 DEC 2006
DP-8060/8045/8035
262
Ver. 1.1 DEC 2006
DP-8060/8045/8035
A B C D E
H6 805 805
803 H6 H6 1002
807 H6
H6 H6
807
804 806
8626 809 1
G6 X5
H6
822
H7 1002 H6
824
828 1002
G6
821
829 822
G6 X5 810
801 823 2
X5
827 541 808
541 826 626 811
G6
830 812
830 H6
822 Y24 814 626
813 3
8626
815 X8
830 816 H6
817
818 4
5
541
1002
Fig. 9-11
H6 7
819
H7
822
822
G6
825
G6
8
Fig. 8 Inverting Automatic Document Feeder (5/8)
263
Ver. 1.1 DEC 2006
DP-8060/8045/8035
264
Ver. 1.1 DEC 2006
DP-8060/8045/8035
A B C D E
X6 X5
8629 931
933 Y19 931
Y10 X5 1
936 937 903
26 807
934
925 932 807
935
H7
Y16 905
Y10 X5 904 906 2
X5 H6
931
933
926 908
803 909
8624
907 910 3
8629 929 923
541
H6
H7 927
830 911
Y16
924
H6 908
919 4
913
912
918 541
928
906 Y16 H6 541
913 Y16
H6 906
X5 5
541 H6
930
H7
917
914
830
916
915
H6 6
Fig. 10-11
8
Fig. 9 Inverting Automatic Document Feeder (6/8)
265
Ver. 1.1 DEC 2006
DP-8060/8045/8035
266
Ver. 1.1 DEC 2006
DP-8060/8045/8035
A B C D E
H6 X5
H6
1004 1007 X5
1002 929
H7 Y16 1003 929 1
541 1005
908 X5
H7
1001
H7 1006
641
1010 1008 2
H6 1011
1013
Fig. 11
8
Fig. 10 Inverting Automatic Document Feeder (7/8)
267
Ver. 1.1 DEC 2006
DP-8060/8045/8035
268
Ver. 1.1 DEC 2006
DP-8060/8045/8035
A B C D E
8604
541 1
Y19 541 Y19
1101 1107
541 1104
1104
Y19
Y24
Y24
1113 1112
1124
1119
1120
X5
1119
1123
6
H7 1126 1118
1125
H7 1115 X8
1122
1116
H7 7
1125
1126
1117
H7
1114
8
Fig. 11 Inverting Automatic Document Feeder (8/8)
269
Ver. 1.1 DEC 2006
DP-8060/8045/8035
270
Ver. 1.1 DEC 2006
DP-8060/8045/8035
A B C D E
X5 1238
1207
From
B X5
X5 1208
1239
1206 1241
1
1242 1240
X5 1209
1204
X8 1239
1228 1239 To
1201 X9 X5
1239 B
1203 1205 X5
1204 To 2
A
1218 From 1206
1202 A
X9 1242
1212 1210
X5 1203 1211 1213 X5
H6 X5
1230
1218
1216
3
1215 1212
1222 1214
X5 X5
1217 1214
Y16 1235
1218 1230
1222 8411
4
1219 H6
1231 1237
1219 8411
8606 1223 1221
X5 Y23
401 1232 X5
1219
8606 1233
1220 1236 1234 5
401
X5 1218
1243
401 6
1225
1224 X9
1243
7
X5
1227
1226
X5
1224
8
1225 Fig. 12 Scanner Unit (1/2)
271
Ver. 1.1 DEC 2006
DP-8060/8045/8035
Scanner Unit
272
Ver. 1.1 DEC 2006
DP-8060/8045/8035
A B C D E
1308 X5
1
1326
1306
1230
1301 1322
H6 2
2839
X3
H6
1322 1230
X5
1303
1318 1302 X3 1307
1230 X9 1309
1322
3
H6 1317 1302
2839
1319 J8
X5
1317 1310
1304 *1309 (Except PK, PT)
H6 1322 *1227 (For PK, PT)
Y21 X5
1230 X9 541 4
1315
1325 Y21 Y21 1316
1304
1312 X5
1305
1313 1311 541
1328
Y21 1323
1317 Y22 5
1314
1321 1320
J7 541
Y21 Y22
Y21
1321
830 541
1315 6
541
641
X5
X5 541
1316
1328
7
1327
Y33
1324 X5 641
1226
641 Y33
1327
8
Fig. 13 Scanner Unit (2/2)
*1309 (Except PK, PT)
*1227 (For PK, PT)
273
Ver. 1.1 DEC 2006
DP-8060/8045/8035
274
Ver. 1.1 DEC 2006
DP-8060/8045/8035
A B C D E
X5
1413
2
8504 X5
401 8504
541 1423
1412 1422
1405 1426
1417 X5
541 3
X8 1421
Y24
1404 1406 H7
1403
1402 1422
1416 4
1418
1420 1424 X5
1419
X8
1418
1408
1409
5
1401
1410
Y14
1407 6
1411
X8
7
1425
8
Fig. 14 Hopper Unit (1/2)
275
Ver. 1.1 DEC 2006
DP-8060/8045/8035
Hopper Unit
276
Ver. 1.1 DEC 2006
DP-8060/8045/8035
A B C D E
J6 1
1502
1501
1504
1503
1505 J7 2
X8
1528 1506
1517
1508
3
1518 1507
X8
1512
1513
1509
1514 4
1510
1515
1513
1516 1511
1527
1519
5
1521
1522
K5 6
1507
K5
1523
1524
7
1525
1526
8
Fig. 15 Hopper Unit (2/2)
277
Ver. 1.1 DEC 2006
DP-8060/8045/8035
278
Ver. 1.1 DEC 2006
DP-8060/8045/8035
A B C D E
1632 1
Y38 1602 1601
X8 2
1605
1604
1606
1607 3
1603
J8
1610 1608
1611
1612
1613
1609 1624
X8
1633 1610 4
1614
1615
X8
1616 1625
1613
1612
1626
1608 5
J8
1617 1627
1629
1618
1623 1628
1634
1622 H7
1619 6
1621 X8
1631
1630
1620
7
X8
1635
8
Fig. 16 Developer Unit (1/2)
279
Ver. 1.1 DEC 2006
DP-8060/8045/8035
Developer Unit
280
Ver. 1.1 DEC 2006
DP-8060/8045/8035
A B C D E
1701
1702
1707 2
1702 1704
1703
1705
1706
908
1710 1708
J8
1711
3
1716
1712
1717
1721
4
1718
1713
1714 5
1715
1719
1713 H6
1720
6
H7
8
Fig. 17 Developer Unit (2/2)
281
Ver. 1.1 DEC 2006
DP-8060/8045/8035
282
Ver. 1.1 DEC 2006
DP-8060/8045/8035
A B C D E
X8
1864
1804
X8 1
1801
X8 1805
1854
1855 1802 1857
1854 1847
1810 2
1865
1855 1811
1807
1803 1850
1844 1848
X5 X8 3
1843
X8
1813
1853 1849 X8
1842
1863 4
X8 1819
1818
1839
1862 X8
1720 1856
1837 1840 1841
X8 1817
1866 1820
1821 X5 5
1834
1822
1909 X5
1836 1851
1835 X8
1846
1845
1823 6
1833 1831
1824
1860
1859 1830
7
X8 X8
1858
1852 1827
1826
1829
1825
1832
1861
1828
8
Fig. 18 Drum Unit (1/2)
283
Ver. 1.1 DEC 2006
DP-8060/8045/8035
Drum Unit
284
Ver. 1.1 DEC 2006
DP-8060/8045/8035
A B C D E
X8
1864
1804
X8 1
1801
X8 1805
1854
1855 1802 1857
1854 1847
1810 2
1865
1855 1811
1807
1803 1850
1844 1848
X5 X8 3
1843
X8
1813
1853 1849 X8
1842
1863 4
X8 1819
1818
1839
1862 X8
1720 1856
1837 1840 1841
X8 1817
1866 1820
1821 X5 5
1834
1822
1909 X5
1836 1851
1835 X8
1846
1845
1823 6
1833 1831
1824
1860
1859 1830
7
X8 X8
1858
1852 1827
1826
1829
1825
1832
1861
1828
8
Fig. 18 Drum Unit (1/2)
285
Ver. 1.1 DEC 2006
DP-8060/8045/8035
Drum Unit
286
Ver. 1.1 DEC 2006
DP-8060/8045/8035
A B C D E
1955
1954
1
J6
1901
1902 1903
2
1904
1905
1922 1907
1923
3
1956
1921
1906
1908
J6
1920 1957
4
1916
1924 Y48
1917
1917 1913
1918 1915
1912 1909
5
1910
1914
1911
1919 1924
1925
8
Fig. 19 Drum Unit (2/2)
287
Ver. 1.1 DEC 2006
DP-8060/8045/8035
For DP-8060/8045
Safety Ref. New
Parts Number Part Name Remarks Destination
Mark No. Parts
2001 DZJL000197 Cover, Cleaning Web C All
2002 DZJL000163 Frame, Rear Cleaning Web C All
2003 FFPKM0343 Web, Cleaning C PM All
Plate, Cleaning Web
2004 DZKP000254 C All
Stopper
2005 DZJA000892 Frame, Front Cleaning Web C All
2006 FFPKF1315 Stopper, Cleaning Web C All
2007 FFPMA04701 Roller, Cleaning Web C All
2009 DZLF000477 Gear, Cleaning Web 1B C All
Shaft, Cleaning Web Idle
2010 DZKG000336 C All
Gear
2011 DZJM000727 Lever, Solenoid C All
2012 L9AAAEFZ0001 Solenoid C All
2013 DZJL000270 Bracket, Solenoid C All
2014 DZJL000162 Bracket, Cleaning Web Gear C All
2015 DZKG000475 Shaft, Cleaning Web Drive N All
2016 DZLF000592 Gear, 1 Way C All
2017 DZLF000476 Gear, Cleaning Web Drive C All
2018 K0BDB0000079 Thermostat C See Note All
2019 DZBL000046 Assembly, Thermistor C All
2020 DZKP000259 Plate, Terminal C All
288
Ver. 1.1 DEC 2006
DP-8060/8045/8035
A B C D E
2001
X5
X5 1
K1
2002
2004
2003
2006 2
X5
2005 504
Y16 2007
D 2009
Y16 2014 X8
C 2015
2011
X8 3
2016
Y16 2017 J7
2032 K2 2010
Y16
2033 2040 X8 2012
E Y14
2033 2013 K2 4
K2 2018
K2
K1
K2 X5 2019
Y36
2031 K1
5
2030
2034
Fig.21-22 2020
E
2029 K2
6
C
D
X8
2028 Black H
Y53
K2
2027 2020 A
B
2021
A
X8 7
K2 Y53
B 2020 K2
X8 Blue G H
2035
K2 F
8
For DP-8060/8045 Fig. 20 Fuser Unit (1/3)
289
Ver. 1.1 DEC 2006
DP-8060/8045/8035
For DP-8060/8045
Safety Ref. New
Parts Number Part Name Remarks Destination
Mark No. Parts
2021 DZJE000915 Cover, Heat Fuser C All
2022 FFPXA65H001 Knob, Jam Release C All
DZGN000031 PU, PUG, PT
2027 Lamp 2, Fuser C PM Except PU,
DZGN000039
PUG, PT
DZGN000030 PU, PUG, PT
2028 Lamp 1, Fuser C PM Except PU,
DZGN000040
PUG, PT
2029 DZJB000249 Bracket, Front Lamp C All
2030 DZJB000250 Bracket, Rear Lamp C All
2031 DZJE000914 Cover, Rear Fuser C All
2032 DZKP000258 Plate 1, Terminal C All
2033 DZKP000260 Plate 2, Terminal C All
2034 DZJF000511 Base, Thermostat C All
PJZSF2754PU1 PU, PUG, PT
2035 Fuser Unit N Except PU,
PJZSF2754PB1
PUG, PT
2039 PJJRC2886Z Harness, HT N All
2040 PJJRC2958Z Harness, HT2 N All
504 XPL2A10WV Pin C All
J7 XUC4VM E-Ring C All
Note:
This part is subject to the U.S. Export Administration Laws and Regulations for export, or re-export to the
countries specified below.
Countries subject to embargo are: Cuba, Iran, Iraq, Libya, North Korea, Syria, and Sudan.
This list is subject to change without further notice.
Purchaser of those countries are requested to order the Fuser Unit Assy instead of this part.
290
Ver. 1.1 DEC 2006
DP-8060/8045/8035
A B C D E
2001
X5
X5 1
K1
2002
2004
2003
2006 2
X5
2005 504
Y16 2007
D 2009
Y16 2014 X8
C 2015
2011
X8 3
2016
Y16 2017 J7
2032 K2 2010
Y16
2033 2040 X8 2012
E Y14
2033 2013 K2 4
K2 2018
K2
K1
K2 X5 2019
Y36
2031 K1
5
2030
2034
Fig.21-22 2020
E
2029 K2
6
C
D
X8
2028 Black H
Y53
K2
2027 2020 A
B
2021
A
X8 7
K2 Y53
B 2020 K2
X8 Blue G H
2035
K2 F
8
For DP-8060/8045 Fig. 20 Fuser Unit (1/3)
291
Ver. 1.1 DEC 2006
DP-8060/8045/8035
For DP-8060/8045
Safety Ref. New
Part Number Part Name Note Destination
Mark No. Parts
2101 DZJE000924 Cover A, Heat Insulation C All
2102 DZJF000607 Guide, Upper Front C All
2105 DZLA000266 Roller, Fuser C PM All
2106 FFPJF0034 Bushing, Insulation C PM All
2107 DZLM000168 Bearing, Fuser Roller C PM All
2108 DZLF000475 Gear, Fuser Roller C PM All
2109 FFPMV0001 Washer C All
2110 DZKN000394 Spring, Clutch C All
2111 DZLF000594 Gear, Clutch C All
2112 FFPMF1059 Gear, Fuser Idle C All
2113 DZJF000510 Guide, Lower Front C PM All
2114 FFPMF1060 Gear 2B, Fuser Idle C All
2115 DZJA000894 Bracket, Upper Fuser C All
2116 DZJC000394 Holder, Magnet C All
2117 FFPKD1374 Washer C All
2118 DZJB000248 Bracket, Support C All
2119 DZJM001144 Washer C All
2120 DZJF000552 Bracket, Upper Separator C All
2121 PJZSF3151PU Assembly, Upper Separator C All
2219 FFPLP0743 Spring, Tension C All
2227 PJHRC0347Z Separator, Upper C PM All
K5 XUC5VM E-Ring C All
K6 XUC6VM E-Ring C All
292
Ver. 1.1 DEC 2006
DP-8060/8045/8035
A B C D E
K1
2101
X5 1
2102
B2
K4 2115
2
2116
Y16
2120
K2
K4 3
Y16 2227
2108 2219
2121
2107
4
2106 2105
Y19 2118
K5 K6 2106
2109
2117 5
2110
2119
2111
2112 2107
Y16
2114
6
2113
8
For DP-8060/8045 Fig. 21 Fuser Unit (2/3)
293
Ver. 1.1 DEC 2006
DP-8060/8045/8035
For DP-8060/8045
Safety Ref. New
Part Number Part Name Note Destination
Mark No. Parts
2201 DZJE000913 Holder, Rear Spring C All
2202 DZKN000278 Spring, Pressure C All
Bracket, Rear Pressure
2203 DZKK000092 C All
Roller
2205 DZHP007236 Assembly, Pressure Roller C PM All
2206 DZJE000912 Holder, Front Spring C All
Bracket, Front Pressure
2207 DZKK000091 C All
Roller
2208 DZMA003389 Frame, Front Paper Guide C All
2209 DZJB000247 Bracket, Bottom C All
2210 DZKP000255 Spring, Lower Separator C All
2211 DZJM001250 Actuator, Exit Sensor C All
2212 DZKQ000101 Spring, Sensor C All
2213 DZJM001232 Guide, Lower Paper Exit C All
2214 DZKP000256 Plate 3, Ground C All
2215 DZLF000474 Gear, Exit Roller C All
2216 FFPMQ0574 Bushing 1, Exit Roller C All
2217 DZLA000264 Roller, Exit C All
2218 DZJA001444 Bracket, Guide Fulcrum C All
2220 DZPG000047 Pin C All
2221 PJBUC0084Z Plate Spring, Pinch Roller C All
2222 DZLA000331 Roller, Pinch C All
2223 PJUKC0093Z Guide, Upper Paper Exit C All
2224 DZKA000042 Band C All
2226 DZKG000335 Shaft, Pressure C All
2228 DZJM001022 Separator, Lower C PM All
2229 DZKG000410 Shaft, Guide Fulcrum C All
2230 DZMA003390 Frame, Rear Paper Guide C All
2231 DZLM000184 Bushing 2, Exit Roller C All
2236 PJJRC2862Z Harness, PFO N All
Assembly, Lower Paper Exit
2238 DZHP009209 C All
Guide
Assembly, Upper Paper Exit
2241 DZHP010118 C All
Guide
2242 B3NZA0000020 Photo Sensor 2 C All
H6 FFPFJ0033B Snap Ring C All
J7 XUC4VM E-Ring C All
J8 XUC7VM E-Ring C All
K6 XUC6VM E-Ring C All
294
Ver. 1.1 DEC 2006
DP-8060/8045/8035
A B C D E
2201
2202 2203
J7
J8 2
Y19 2205
2206 3
K6 J8
2207
2230
2226 J7
2238
2210 2212 2202
2242
2211 4
2228
K6 Y19
2214
Y19 2236
2215
J7 2228 2210
2231
K1 5
2213
2208
2217
H6
Y16 2216
2218 J7
2224 2222 H6
2221 2229 6
2220 Y16
3P 2218 2209
2223 7
2241
8
For DP-8060/8045 Fig. 22 Fuser Unit (3/3)
295
Ver. 1.1 DEC 2006
DP-8060/8045/8035
For DP-8035
Safety Ref. New
Parts Number Part Name Remarks Destination
Mark No. Parts
2001 DZJL000197 Cover, Cleaning Web C All
2002 DZJF000548 Frame, Rear Cleaning Web C All
2003 FFPKM0343 Web, Cleaning C PM All
Plate, Cleaning Web
2004 DZKP000254 C All
Stopper
2005 DZJA001163 Frame, Front Cleaning Web C All
2006 FFPKF1315 Stopper, Cleaning Web C All
2007 FFPMA04701 Roller, Cleaning Web C All
2009 DZLF000477 Gear, Cleaning Web 1B C All
Shaft, Cleaning Web Idle
2010 DZKG000336 C All
Gear
2011 DZJM000727 Lever, Solenoid C All
2012 L9AAAEFZ0001 Solenoid C All
2013 DZJL000270 Bracket, Solenoid C All
2014 DZJL000162 Bracket, Cleaning Web Gear C All
2015 DZKG000475 Shaft, Cleaning Web Drive N All
2016 DZLF000592 Gear, 1 Way C All
2017 DZLF000476 Gear, Cleaning Web Drive C All
2018 K0BDB0000079 Thermostat C See Note All
2019 DZBL000046 Assembly, Thermistor C All
2020 DZKP000259 Plate, Terminal C All
2021 DZJE001001 Cover, Front Fuser C All
2022 FFPXA65H001 Knob, Jam Release C All
DZGN000031 PU, PUG, PT
2027 Lamp 2, Fuser C PM Except PU,
DZGN000039
PUG, PT
DZGN000036 PU, PUG, PT
2028 Lamp 1, Fuser C PM Except PU,
DZGN000041
PUG, PT
2029 DZJB000286 Bracket, Front Lamp C All
2030 DZJB000287 Bracket, Rear Lamp C All
296
Ver. 1.1 DEC 2006
DP-8060/8045/8035
A B C D E
2001
K1 X5
X5 1
2002
2004
2003
2006 2
X5
Y16 D
2005 504
2007
G 2009
Y16 Y16 2014 X8
2015
C X8 2011
X8 3
2016
Y16 2017 J7
K2 2010
2032 Y16
2040 X8
2036 2012
2037 E 2013 Y14
K2 Y36 2033
2018 K2 4
K2 K1
K2 X5 2019
Y36
K1
2031 5
2030
2034
2020
Fig.21-22 E
G
2029 K2
6
C
Black
K X8
D 2028 Y53
B
2020 K2
F
2027 Y53
2021 Brown
A
A X8
H K2 K2 7
Y53
B
2020
X8 K2 I
J Blue
2035
X8 H K
2020 Y53
2022 2038
K2 I
F White
8
For DP-8035 Fig. 20 Fuser Unit (1/3)
297
Ver. 1.1 DEC 2006
DP-8060/8045/8035
For DP-8035
Safety Ref. New
Parts Number Part Name Remarks Destination
Mark No. Parts
2031 DZJE001230 Cover, Rear Fuser C All
2032 DZKP000382 Plate 1, Terminal C All
2033 DZKP000381 Plate 2, Terminal C All
2034 DZJF000669 Base, Thermostat C All
PJZSF2755PU1 PU, PUG
PJZSF2751PT1 PT
2035 Fuser Unit N
Except PU,
PJZSF2755PB1
PUG, PT
2036 K5X184BH0001 Thermal Fuse C See Note All
2037 DZBL000045 Assembly, Thermistor C All
2038 PJJRC2885Z Harness, HT35 N All
2040 PJJRC2958Z Harness, HT2 N All
504 XPL2A10WV Pin C All
J7 XUC4VM E-Ring C All
Note:
This part is subject to the U.S. Export Administration Laws and Regulations for export, or re-export to the
countries specified below.
Countries subject to embargo are: Cuba, Iran, Iraq, Libya, North Korea, Syria and Sudan.
This list is subject to change without further notice.
Purchaser of those countries are requested to order the Fuser Unit Assy instead of this part.
298
Ver. 1.1 DEC 2006
DP-8060/8045/8035
A B C D E
2001
K1 X5
X5 1
2002
2004
2003
2006 2
X5
Y16 D
2005 504
2007
G 2009
Y16 Y16 2014 X8
2015
C X8 2011
X8 3
2016
Y16 2017 J7
K2 2010
2032 Y16
2040 X8
2036 2012
2037 E 2013 Y14
K2 Y36 2033
2018 K2 4
K2 K1
K2 X5 2019
Y36
K1
2031 5
2030
2034
2020
Fig.21-22 E
G
2029 K2
6
C
Black
K X8
D 2028 Y53
B
2020 K2
F
2027 Y53
2021 Brown
A
A X8
H K2 K2 7
Y53
B
2020
X8 K2 I
J Blue
2035
X8 H K
2020 Y53
2022 2038
K2 I
F White
8
For DP-8035 Fig. 20 Fuser Unit (1/3)
299
Ver. 1.1 DEC 2006
DP-8060/8045/8035
For DP-8035
Safety Ref. New
Part Number Part Name Note Destination
Mark No. Parts
2101 DZJE000947 Cover A, Heat Insulation C All
2102 DZJF000600 Guide, Upper Front C All
DZLA000286 Except PT
2105 Roller, Fuser C PM
PJDRC0124Z PT
2106 FFPJF0034 Bushing, Insulation C PM All
2107 DZLM000168 Bearing, Fuser Roller C PM All
2108 DZLF000558 Gear, Fuser Roller C PM All
2109 FFPMV0001 Washer C All
2110 DZKN000394 Spring, Clutch C All
2111 DZLF000594 Gear, Clutch C All
2112 FFPMF1059 Gear, Fuser Idle C All
2113 DZJF000550 Guide, Lower Front C PM All
2114 FFPMF1060 Gear 2B, Fuser Idle C All
2115 DZJA000997 Bracket, Upper Fuser C All
2116 DZJC000394 Holder, Magnet C All
2117 FFPKD1374 Washer C All
2118 DZJB000248 Bracket, Support C All
2119 DZJM001144 Washer C All
2120 DZJF000551 Bracket, Upper Separator C All
2121 PJZSF3152PU Assembly, Upper Separator C All
2219 FFPLP0743 Spring, Tension C All
2227 PJHRC0347Z Separator, Upper C PM All
K5 XUC5VM E-Ring C All
K6 XUC6VM E-Ring C All
300
Ver. 1.1 DEC 2006
DP-8060/8045/8035
A B C D E
K1
2101
X5 1
2102
B2
K4 2115
2
2116
Y16
2120
K2
K4 3
Y16 2227
2108 2219
2121
2107
4
2106 2105
Y19 2118
K5 K6 2106
2109
2117 5
2110
2119
2111
2112 2107
Y16
2114
6
2113
8
For DP-8035 Fig. 21 Fuser Unit (2/3)
301
Ver. 1.1 DEC 2006
DP-8060/8045/8035
For DP-8035
Safety Ref. New
Part Number Part Name Note Destination
Mark No. Parts
2201 DZJE001096 Holder, Rear Spring N All
2202 DZNK000372 Spring, Pressure C All
Bracket, Rear Pressure
2203 DZKK000110 N All
Roller
2206 DZJE001095 Holder, Front Spring N All
Bracket, Front Pressure
2207 DZKK000109 N All
Roller
2208 DZMA003581 Frame, Front Paper Guide C All
2209 DZJB000247 Bracket, Bottom C All
2210 DZKP000255 Spring, Lower Separator C All
2211 DZJM001251 Actuator, Exit Sensor C All
2212 DZKQ000101 Spring, Sensor C All
2213 DZJM000826 Guide, Lower Paper Exit C All
2214 DZKP000256 Plate 3, Ground C All
2215 DZLF000644 Gear, Exit Roller C All
2216 FFPMQ0574 Bushing 1, Exit Roller C All
2217 DZLA000264 Roller, Exit C All
2218 DZJA001444 Bracket, Guide Fulcrum C All
2220 DZPG000047 Pin C All
2221 PJBUC0084Z Plate Spring, Pinch Roller C All
2222 DZLA000331 Roller, Pinch C All
2223 PJUKC0092Z Guide, Upper Paper Exit C All
2224 DZKA000042 Band C All
2226 DZKG000335 Shaft, Pressure C All
2228 DZJM001022 Separator, Lower C PM All
2229 DZKG000410 Shaft, Guide Fulcrum C All
2230 DZJL000268 Frame, Rear Paper Guide C All
2231 DZLM000184 Bushing 2, Exit Roller C All
2232 PJZSF2752AZ Assembly, Pressure Roller N PM All
2236 PJJRC2862Z Harness, PFO N All
2237 DZHD000026 Sheet C All
Assembly, Lower Paper Exit
2238 DZHP008313 C All
Guide
Assembly, Upper Paper Exit
2241 DZHP010119 C All
Guide
2242 B3NZA0000020 Photo Sensor 2 C All
H6 FFPFJ0033B Snap Ring C All
J7 XUC4VM E-Ring C All
J8 XUC7VM E-Ring C All
K6 XUC6VM E-Ring C All
302
Ver. 1.1 DEC 2006
DP-8060/8045/8035
A B C D E
2201
2202 2203
J7
J8 2
Y19
2232
2206 3
K6 J8
2207
2230
2226 J7
2238
2210 2212 2202
2242
2211 4
2237 2228
K6 Y19
2214
Y19 2236
2215
J7 2228 2210
2231
K1 5
2213
2208
2217
H6
Y16 2216
2218 J7
2224 2222 H6
2221 2229 6
2220 Y16
2218
3P 2209
2223 7
2241
8
For DP-8035 Fig. 22 Fuser Unit (3/3)
303
Ver. 1.1 DEC 2006
DP-8060/8045/8035
304
Ver. 1.1 DEC 2006
DP-8060/8045/8035
A B C D E
2302
2337 2352
2301 Y48 2306
X8
2335
2363 2342 2305 1
Y48 X5 X8
2307
2303
2358
2359
2338 2334 2309 2339
2341
2321
X8 1914 2
2322 2308
2345
X8
2357
J8
8607 2312 X8 3
2431 X5 J8 2310
2343 2320 2312 2333
2323 J8
2362 2312
J8 2317 2319 2357
X5 J8
2312 X8
H6 2312
2360
208 H6 4
J8 2312 2317 G6 2313
Y24
208
J8 2340
2324 2318
2312 2317
2325
Y2 541
2312
2364 J8
H9 5
2317
To 541
A 2314
K9 541 2333 2340
2326 2362 G6
2603 2311 2316
6
2362
2315
2344 2332
2350
2328 7
2331 X3
2364 K9
2349
From 2346 Y23
A X5
2347 2348
2356 2327
8
Fig. 23 Automatic Duplex Unit (1/4)
305
Ver. 1.1 DEC 2006
DP-8060/8045/8035
306
Ver. 1.1 DEC 2006
DP-8060/8045/8035
A B C D E
2302
2337 2352
2301 Y48 2306
X8
2335
2363 2342 2305 1
Y48 X5 X8
2307
2303
2358
2359
2338 2334 2309 2339
2341
2321
X8 1914 2
2322 2308
2345
X8
2357
J8
8607 2312 X8 3
2431 X5 J8 2310
2343 2320 2312 2333
2323 J8
2362 2312
J8 2317 2319 2357
X5 J8
2312 X8
H6 2312
2360
208 H6 4
J8 2312 2317 G6 2313
Y24
208
J8 2340
2324 2318
2312 2317
2325
Y2 541
2312
2364 J8
H9 5
2317
To 541
A 2314
K9 541 2333 2340
2326 2362 G6
2603 2311 2316
6
2362
2315
2344 2332
2350
2328 7
2331 X3
2364 K9
2349
From 2346 Y23
A X5
2347 2348
2356 2327
8
Fig. 23 Automatic Duplex Unit (1/4)
307
Ver. 1.1 DEC 2006
DP-8060/8045/8035
308
Ver. 1.1 DEC 2006
DP-8060/8045/8035
A B C D E
2419 2404 2406 2915
2410 2407
K5
2405
1507 2402 2915
2403 1
2406
2413 2432
2401 2409
2405
2415
1507
2411 2
2435
2412
2409
X8 K5
2416 2410
2430 2414
2413
3
401
X5
541
541 2417
2418
2433
2421 2431
L6 4
G6
2420
2423
Fig. 25 Y23
2422
K8
5
2424
2434
X5
822
2331
2428
2425
K9
1002 7
2423 H6
2427
2429 H6
X5 1002 2426
1002
H6
2434 2427 H6
8
Fig. 24 Automatic Duplex Unit (2/4)
309
Ver. 1.1 DEC 2006
DP-8060/8045/8035
310
Ver. 1.1 DEC 2006
DP-8060/8045/8035
A B C D E
X8 Y23
2501 2529
L1
2534 L2 1
2502 2506
X8
2501
L1
2507 2508
Y43 X8
2503 2
2504 2502
2511 2513 L2
2407 2505
2519 2502 2509
2504
2503
2512 X8
2502 2510 3
2503
2504 Y43
2407
2502
2516 2504 2503 2511
2503 2514 4
2504
401 2515
2407
2504 2518
2503 401
2517
5
X5 2523
2522
2526
2527
8
Fig. 25 Automatic Duplex Unit (3/4)
311
Ver. 1.1 DEC 2006
DP-8060/8045/8035
312
Ver. 1.1 DEC 2006
DP-8060/8045/8035
A B C D E
X3
2602
J8 1
2603
2601
541 To
541 A 2624
X5 K5
2604
2
2606
J7 2605
2622
J7 K9
K5
2610 2607
3
1002
2609
2608
2608
X5
4
2611
541
2612 J7
2617 X5 2621
2603
2616 5
541 541
2613 1002
J6
To 6
A 1002
2623
2733
2624
2619 7
2624
From
A 2620
8
Fig. 26 Automatic Duplex Unit (4/4)
313
Ver. 1.1 DEC 2006
DP-8060/8045/8035
314
Ver. 1.1 DEC 2006
DP-8060/8045/8035
A B C D E
2702
2748
L1 2701
2752
2705
2703 2751 1
X5
2706
2740
L2 928 2708
2744
2741
2704 928 2707
928 2
2728 2742 X5
B2
2756 2743 929 X5
3
2729
541
2745
2717
2716 R1
2724 2715 4
X5
2727 2718 2741 2709
2755 L2
2730 2754 2714 2749
2723 2711
2713
2712 2710
2722
2726 2750
2721 2719 J6
2725 5
K9
2720
2733
2731 2750 2753
2734
J6
8520
2733 6
2735 X5
2734
X5 2737
2738
2736
2739
7
3F
8
Fig. 27 Drive Unit (1/2)
315
Ver. 1.1 DEC 2006
DP-8060/8045/8035
Drive Unit
Note:
* This Kit includes the parts shown in Figures 27, 28, and 36.
316
Ver. 1.1 DEC 2006
DP-8060/8045/8035
A B C D E
2702
2748
L1 2701
2752
2705
2703 2751 1
X5
2706
2740
L2 928 2708
2744
2741
2704 928 2707
928 2
2728 2742 X5
B2
2756 2743 929 X5
3
2729
541
2745
2717
2716 R1
2724 2715 4
X5
2727 2718 2741 2709
2755 L2
2730 2754 2714 2749
2723 2711
2713
2712 2710
2722
2726 2750
2721 2719 J6
2725 5
K9
2720
2733
2731 2750 2753
2734
J6
8520
2733 6
2735 X5
2734
X5 2737
2738
2736
2739
7
3F
8
Fig. 27 Drive Unit (1/2)
317
Ver. 1.1 DEC 2006
DP-8060/8045/8035
Drive Unit
318
Ver. 1.1 DEC 2006
DP-8060/8045/8035
A B C D E
8614
2836 J6
1
928 2838
Y19 2839 2752
2801 2849 K5
2803
2838
2804 K5
K9
2809 2846
2805 2
8511 2845
2802 8511 2839
Y19 G6
2810 2806
2840
2808
2841
2849 2840 2839
G6 2842
3
2811 2807
J7
K9 2839
2814
2817
2816 8511
2813 G6
2815 2806
2812
2838 4
K9 2820 2709
2847
X5 2823 2848
2841
2842
2825
2844
5
2824 2835
X5 K5
2826 Y19
2827
2828 2843
2839 6
2830
2829
K5
2833 2834 7
X5 K5
J7
2831
2832
8
Fig. 28 Drive Unit (2/2)
319
Ver. 1.1 DEC 2006
DP-8060/8045/8035
Drive Unit
Note:
* This Kit includes the parts shown in Figures 27, 28, and 36.
320
Ver. 1.1 DEC 2006
DP-8060/8045/8035
A B C D E
8614
2836 J6
1
928 2838
Y19 2839 2752
2801 2849 K5
2803
2838
2804 K5
K9
2809 2846
2805 2
8511 2845
2802 8511 2839
Y19 G6
2810 2806
2840
2808
2841
2849 2840 2839
G6 2842
3
2811 2807
J7
K9 2839
2814
2817
2816 8511
2813 G6
2815 2806
2812
2838 4
K9 2820 2709
2847
X5 2823 2848
2841
2842
2825
2844
5
2824 2835
X5 K5
2826 Y19
2827
2828 2843
2839 6
2830
2829
K5
2833 2834 7
X5 K5
J7
2831
2832
8
Fig. 28 Drive Unit (2/2)
321
Ver. 1.1 DEC 2006
DP-8060/8045/8035
322
Ver. 1.1 DEC 2006
DP-8060/8045/8035
A B C D E
H5 1
2916
2901
J7 2903
X3 2902 2
2904
2907
2908 2905
2914 2904
J7
3
2909
2910
Y24
2906
2915
K9 2912 2917
2911 X8
2915 4
2910 2909
2913
2919
5
X8
2918
6
8
Fig. 29 Paper Feed Module (1/4)
323
Ver. 1.1 DEC 2006
DP-8060/8045/8035
324
Ver. 1.1 DEC 2006
DP-8060/8045/8035
A B C D E
K5
3001 1
2603
3002
3010
K5
3001
2603
G6 G6 2
822
3003
401
3004
3005
8521 X5
3
G6 3003
822
3006
8521
401 3009
4
3007
2517
X5
3004
5
8521
401
3011
6
3008 Y19
2517
3004
8521 X5
401
8
Fig. 30 Paper Feed Module (2/4)
325
Ver. 1.1 DEC 2006
DP-8060/8045/8035
326
Ver. 1.1 DEC 2006
DP-8060/8045/8035
A B C D E
1
541
3101
X5
To 3129 3102
541 A
3103
3104
641
3105
H6 H6 3102 X5 3128 2
3113 1024
K5 3107 3106
H6 H6
3105 H6
208 3108
Y16
X5 3111 3
3110 3127
3109
641
208
3130
X8 H6
641
4
From 3126
A
3118
3120
3115 3102
3129 X8
3114 3116
H7 208
3117 5
3102 Y25
3119 X5
3121
3125 208
X5 3124 6
To
3123 3129 A
To
A
401
3129
To
A
401
3129
3122
X5 7
8
Fig. 31 Paper Feed Module (3/4)
327
Ver. 1.1 DEC 2006
DP-8060/8045/8035
328
Ver. 1.1 DEC 2006
DP-8060/8045/8035
A B C D E
3201
2
3203
3202
3204
3206 3205
3207
3
3208
3209
3210
3212
X8 3211
4
H7
3221
3213 5
3215
H6 3216 3214
208
K5
3217
6
J7 3218
3218 208
H6
K5 X8
3219
7
3220
8
Fig. 32 Paper Feed Module (4/4)
329
Ver. 1.1 DEC 2006
DP-8060/8045/8035
330
Ver. 1.1 DEC 2006
DP-8060/8045/8035
A B C D E
S6
3329 3308
X5 3318
X5
X5 3325 2
8404
3327
X5 3320
X6 8402
3305
3305 X5
3
8401
X5
3315 X5 3326
928
3306
929 3311 4
3324
928
3323
541
541
928
5
541
8701
3321
8702
X5 3322 X5 X5
3314 6
3307 3312
X5 3313
3328
3307
928
X5 7
928 8602
X5
8706 928 X5 3316
X5 8704
8715 X5 X5
X5 928 (100V)
929 (200V)
8
Fig. 33 Electrical Parts (1/4)
331
Ver. 1.1 DEC 2006
DP-8060/8045/8035
Electrical Parts
332
Ver. 1.1 DEC 2006
DP-8060/8045/8035
A B C D E
S6
3329 3308
X5 3318
X5
X5 3325 2
8404
3327
X5 3320
X6 8402
3305
3305 X5
3
8401
X5
3315 X5 3326
928
3306
929 3311 4
3324
928
3323
541
541
928
5
541
8701
3321
8702
X5 3322 X5 X5
3314 6
3307 3312
X5 3313
3328
3307
928
X5 7
928 8602
X5
8706 928 X5 3316
X5 8704
8715 X5 X5
X5 928 (100V)
929 (200V)
8
Fig. 33 Electrical Parts (1/4)
333
Ver. 1.1 DEC 2006
DP-8060/8045/8035
Electrical Parts
334
Ver. 1.1 DEC 2006
DP-8060/8045/8035
A B C D E
8601
3403 X5
3401
1
X5
X5
X5
8502
X5 2
3419
3418 928
X5 3406 3407
8406 8606
P7
1241
3
3408 1240
3421 8501
X5 3420
3409
3415 X5
3410 3402
4
Y46 X5
X9
Y2 R8
5
X5
8603 X5 8407
3405
3417
3404 3411 Y19
3416 6
2849
X5
3413 3412
7
3414
8
Fig. 34 Electrical Parts (2/4)
335
Ver. 1.1 DEC 2006
DP-8060/8045/8035
Electrical Parts
336
Ver. 1.1 DEC 2006
DP-8060/8045/8035
A B C D E
3520 K5
H6
1
3540 208
X5
3539 3519
X5 X5 3518
3541
3503 208 H6
K5 3521
928 X5 3522
3501 3516 3517
541 2
3502
541 3505 X5 8607 3515
3504 401 X5
X5 8605
830 929 3523
3514 X8
X5
3545 3524
541
3544 3533 3529 3
3545 3506 X5
3525 3546
3544 X5
8612
X5 X5 4
3507
3533
X8
3513 5
X5
3508
8509
3537 X5 X5
3543
3528 X5
3509
6
X5
3527
X5 X5 3542
3535 X5
3538
K5 3512
8509
541
503 7
X5 3531 541
3511 928
541
X5
3526 X5 X5
928 3536 X5
8
Fig. 35 Electrical Parts (3/4)
337
Ver. 1.1 DEC 2006
DP-8060/8045/8035
Electrical Parts
338
Ver. 1.1 DEC 2006
DP-8060/8045/8035
A B C D E
3520 K5
H6
1
3540 208
X5
3539 3519
X5 X5 3518
3541
3503 208 H6
K5 3521
928 X5 3522
3501 3516 3517
541 2
3502
541 3505 X5 8607 3515
3504 401 X5
X5 8605
830 929 3523
3514 X8
X5
3545 3524
541
3544 3533 3529 3
3545 3506 X5
3525 3546
3544 X5
8612
X5 X5 4
3507
3533
X8
3513 5
X5
3508
8509
3537 X5 X5
3543
3528 X5
3509
6
X5
3527
X5 X5 3542
3535 X5
3538
K5 3512
8509
541
503 7
X5 3531 541
3511 928
541
X5
3526 X5 X5
928 3536 X5
8
Fig. 35 Electrical Parts (3/4)
339
Ver. 1.1 DEC 2006
DP-8060/8045/8035
Electrical Parts
Note:
* This Kit includes the parts shown in Figures 27, 28, and 36.
340
Ver. 1.1 DEC 2006
DP-8060/8045/8035
A B C D E
3601
3604 X8 3603
1
X8
3602
3606
X8
2
3605 3607
2752
3617 2709
X5 3618
X5
3619 X5 3
401 3620
8615 3610
3608 3627 3611
3609
X5
4
X5
3625
8705
5
3613 3614 3615
Y37
3622
3612
X5
6
3626
3616 7
X5
Y13
3623
X5
3624
8
Fig. 36 Electrical Parts (4/4)
341
Ver. 1.1 DEC 2006
DP-8060/8045/8035
342
Ver. 1.1 DEC 2006
DP-8060/8045/8035
A B C D E
K6 3804
1
401
3803
3828 3805
X5
8709 3816
X5 2
3826 3818
401
3827
X5 Y19
928
541 5
3810 3821
Y19
3811
J6
Y19 6
3830 2423
Y19
3916
3814 3815
3830 2423
Y19 3817
Y19
X5 3813
3815 7
X5 3916
8607
J6
3829
8610
L4 3524
8
Fig. 38 Frame Parts (1/5)
343
Ver. 1.1 DEC 2006
DP-8060/8045/8035
Frame Parts
344
Ver. 1.1 DEC 2006
DP-8060/8045/8035
A B C D E
X5
3902
3901
1
3905 3928
X5
X9 3903
3906
3904
3903 3926 2
3932
X5
3907
3909 3908
3929 X5
X5
3925 3930 3
3908
X1
Y19
8616
3910 X5 4
3924 3927
401 3933
Y19
3931 X8
3923
K5
5
X5 3911 3922 3920
X5 3919
3918
3921
2423
6
X5 3912
Y19
3815 J6 K5
3916
3921 3920
Y19
3915
3914 3815 2423 3919
3915
3917 7
Y19
J6 Y19 3918
3815
541 J6
3916
3916 J6 3815
3916
3913 Y19 8
Y19 3917
Y19 Fig. 39 Frame Parts (2/5)
345
Ver. 1.1 DEC 2006
DP-8060/8045/8035
Frame Parts
346
Ver. 1.1 DEC 2006
DP-8060/8045/8035
A B C D E
4023 401 8516
4024 8514 X5
4001 4008
4026
Y26 541 4006 X5 401 1
4007 401
8516
4025
X5 4005 4029
X5 4009
1709 4026 (Except PU, PUG, PT)
Q3
4002 4003 X5
4009 (For PU, PUG, PT) 2
4004
4010
4033
4032
4005
4028
4004 X5 3
4021 L1
4007 4029
4025 4026 4030
4027
4011
1709
4012
4020
Y40 4
4019
8517 X5 4014
4013 4035
4034
Y19
4022
X5
5
4016 4031
4027 4013
Y19
4012 Y40
X5 4211 Y19
4016 4015
4035 4014 Y40
X5 6
4016 X9
4034 Y19
Y40 4017
4031 X5
Y19
4211
4015 7
4018
X9 X5
Y19
4018
8
Fig. 40 Frame Parts (3/5)
347
Ver. 1.1 DEC 2006
DP-8060/8045/8035
Frame Parts
348
Ver. 1.1 DEC 2006
DP-8060/8045/8035
A B C D E
4101
1
4102
4126 J6
X9 4103
X9
4109 X9 4137 1720
4118
Q7 2
4119
4110 4108
4113 4116
4111
4121
4115 3
4112 4105 4125
4104
K5 X5
4106 4114
4
K5 4124
4123
8615
X5 401
X9
3608 5
4120
4107
1838
6
4122
4129
4123
4128
8
Fig. 41 Frame Parts (4/5)
349
Ver. 1.1 DEC 2006
DP-8060/8045/8035
Frame Parts
350
Ver. 1.1 DEC 2006
DP-8060/8045/8035
A B C D E
8611 L4
4204
4228 *3817 (For PU, PUG)
*4219 (Except PU, PUG) 1
X8
X5 4203
4226 4225
4219
4202
L4 8611
4201 X8 2
L4 4205
X5
8611
4217
*3817 (For PU, PUG)
*4219 (Except PU, PUG) X5
4227 3
8609 4222
4206 X5
4216
L5 X9 4218
N8
4220 4208
4221 4
8609
4209 X5 X5 4207 4223
4215
4123 4231 5
4027
4012
4229
4224
N7
X8 4210 X5
4219
4034
8609 X5 Y19 4031 6
4234 4214 4014
4122
Y19 X5
4212 Y19
4213
4211
4233 X5
4027 7
4232 4035 Y19 4012
4034 4235
X5 4015 4035
4031 X9
4015 4014
8
X9 Fig. 42 Frame Parts (5/5)
*3817 (For PU, PUG)
*4219 (Except PU, PUG)
351
Ver. 1.1 DEC 2006
DP-8060/8045/8035
Frame Parts
352
Ver. 1.1 DEC 2006
DP-8060/8045/8035
A B C D E
8611 L4
4204
4228 *3817 (For PU, PUG)
*4219 (Except PU, PUG) 1
X8
X5 4203
4226 4225
4219
4202
L4 8611
4201 X8 2
L4 4205
X5
8611
4217
*3817 (For PU, PUG)
*4219 (Except PU, PUG) X5
4227 3
8609 4222
4206 X5
4216
L5 X9 4218
N8
4220 4208
4221 4
8609
4209 X5 X5 4207 4223
4215
4123 4231 5
4027
4012
4229
4224
N7
X8 4210 X5
4219
4034
8609 X5 Y19 4031 6
4234 4214 4014
4122
Y19 X5
4212 Y19
4213
4211
4233 X5
4027 7
4232 4035 Y19 4012
4034 4235
X5 4015 4035
4031 X9
4015 4014
8
X9 Fig. 42 Frame Parts (5/5)
*3817 (For PU, PUG)
*4219 (Except PU, PUG)
353
Ver. 1.1 DEC 2006
DP-8060/8045/8035
354
Ver. 1.1 DEC 2006
DP-8060/8045/8035
A B C D E
J7 J7 4330 4329 4329 X5
4326
4328
4329 1
4301
X5 4325 4324
X8
K6 X8 4323
2
X5 4322
X5 4337
4304 J2
4332
4338
4305
K5 X8 3
4306 4304
4307 4305
4340 4343 Y1
4308 J2
4327
4309 4333
Y2
4
4321
4334
4312 4332 4302
4336
4310 K5
4311 4320
4309 5
4308
4340 K5
X5
K5
4341 4315 2423 4318
Y2
K5
4319 6
4313
J6 4316
4313 4342 N1
J6
Y3 4317
4315
K8
2423
4335 4314
4314
K5
8
Fig. 43 1st Paper Tray
355
Ver. 1.1 DEC 2006
DP-8060/8045/8035
356
Ver. 1.1 DEC 2006
DP-8060/8045/8035
A B C D E
4427
4402 1
4311
4428 4425
X8
4338 4418
Y19 4430
Y19 Y24 2
4401
4403
4430
4417
4418
4418
3
4418 4404
Y24
4411 4421 4426
Y23
X8
4412 X8
4409 4
4429 4410
2340
G6 4408
2340 X8 4420
4414
J7
X8
4418 4405
5
4423 4424
X8 4406
4314
4422
4410 6
4415
4416
X8
4419 K5
X8
7
4407
4432
4314 K5
8
Fig. 44 2nd Paper Tray
357
Ver. 1.1 DEC 2006
DP-8060/8045/8035
358
Ver. 1.1 DEC 2006
DP-8060/8045/8035
A B C D E
4513
4501 J2
4502
2
4503
3
4513
Fig. 46
4505
4504
4506
4511
401
4
Y37
4507
4306
401
4514
4512 5
401
4515
4409
H5
4508 6
M9
4510
7
4509
8
Fig. 45 Sheet Bypass (1/2)
359
Ver. 1.1 DEC 2006
DP-8060/8045/8035
Sheet Bypass
360
Ver. 1.1 DEC 2006
DP-8060/8045/8035
A B C D E
4649
X5 4644
4639 J6
4635
1
J6
4635
4633
H6 Y16 Y21
Y23
4606
2
4601
4602
4607
4603
Y21
K5 4648
4605
4645 3
4604
4634 K5
4648
3205
4648 4608
4609
K5 Y19 4
4648 H6
4646
4647 4641
4629 4630 4610
4623 H6
4648 4611
K5
K5 4602
4648 5
4643 4632 4601
4624 4636
J7 H7 4637 4642
4625
K5 4649 4612
4613 H6
4623 401 4627 4632
4626 4628 L7
6
K5
X5
4648 4631
L7
4619 L7
4622
4621 4614
K5 4618
L7
541
7
4617
L7
4638 4615
4616
X5
L7
4620 Y19 8
Fig. 46 Sheet Bypass (2/2)
361
Ver. 1.1 DEC 2006
DP-8060/8045/8035
Sheet Bypass
362
Ver. 1.1 DEC 2006
DP-8060/8045/8035
A B C D E
4649
X5 4644
4639 J6
4635
1
J6
4635
4633
H6 Y16 Y21
Y23
4606
2
4601
4602
4607
4603
Y21
K5 4648
4605
4645 3
4604
4634 K5
4648
3205
4648 4608
4609
K5 Y19 4
4648 H6
4646
4647 4641
4629 4630 4610
4623 H6
4648 4611
K5
K5 4602
4648 5
4643 4632 4601
4624 4636
J7 H7 4637 4642
4625
K5 4649 4612
4613 H6
4623 401 4627 4632
4626 4628 L7
6
K5
X5
4648 4631
L7
4619 L7
4622
4621 4614
K5 4618
L7
541
7
4617
L7
4638 4615
4616
X5
L7
4620 Y19 8
Fig. 46 Sheet Bypass (2/2)
363
Ver. 1.1 DEC 2006
DP-8060/8045/8035
364
Ver. 1.1 DEC 2006
DP-8060/8045/8035
A B C D E
4311
4402 1
4418
Y23
4411
4429
2
4414 4424
J7
4423 X8
4422
4418
4418
X8 X8 4418 3
4338 4430
X8
X8 4701
X8
4412
4405
4410 4314
4406
6
Y24
X8 4415
K5 X8
4416
4314 4407
4419
K5 7
8
Fig. 47 3rd/4th Paper Tray
365
Ver. 1.1 DEC 2006
DP-8060/8045/8035
366
Ver. 1.1 DEC 2006
DP-8060/8045/8035
A B C D E
4801
X8
2
4410
4408
X8
4
4431
4410 4314
4406
5
X8
4415 K5 6
4416
4314
K5
8
Fig. 48 4th Paper Tray (Storage Tray)
367
Ver. 1.1 DEC 2006
DP-8060/8045/8035
368
Ver. 1.1 DEC 2006
DP-8060/8045/8035
A B C D E
4927
1
4943
1635 4926
2
4912
4947 4948
4909
3
4925
4908
4941
4907
4
4941
4911
4949
4942 5
4906
4942 4904
6
4943 4905
7
8
For PU (USA/Canada, etc.) Fig. 50 Packing and Accessories
369
Ver. 1.1 DEC 2006
DP-8060/8045/8035
370
Ver. 1.1 DEC 2006
DP-8060/8045/8035
A B C D E
4927
1
4943
4926
2
4912
4947 4948
4909
3
4925
4908
4941
4907
4
4941
4911
4949
4942 5
4906
4942 4904
6
4943 4905
7
8
For PK (China) Fig. 51 Packing and Accessories
371
Ver. 1.1 DEC 2006
DP-8060/8045/8035
372
Ver. 1.1 DEC 2006
DP-8060/8045/8035
A B C D E
4901
4922
4912
4947
4909
4948
2
4941
4333 4908 3
4907
4941
4
4911
4949
4942
4906
4942
4944
4922
4905
7
8
For Other Destinations Fig. 52 Packing and Accessories
373
Ver. 1.1 DEC 2006
DP-8060/8045/8035
5.22. Software CD
374
Ver. 1.1 DEC 2006
DP-8060/8045/8035
A B C D E
3
4950, 4951
8
Fig. 49 Software CD
375
Ver. 1.1 DEC 2006
DP-8060/8045/8035
376
Ver. 1.1 DEC 2006
DP-8060/8045/8035
A B C D E
X5
8013 2
4123
X5
8014
8001
3
8005
Y13 8004
X5 X5
8611 401
8610 H6
8006 8008
8002 4
401
8003 8009
8007
G6
Y19 8017
S6 X5
X8 5
G6
1123 8017
X8
1123
8010 L6
8015
8012 8016
8011 6
8
Fig. 80 Paper Exit Transportation (1/4)
377
Ver. 1.1 DEC 2006
DP-8060/8045/8035
378
Ver. 1.1 DEC 2006
DP-8060/8045/8035
A B C D E
H7 8136 Y2
8112
401
8148 8111 1
8141
8109 X5 8110
8108 8114
8106
8142
8113 H7
8610 8128 X5
8107
8150 Y26
2
8127 8101 401
X5 4231
8610 8610
8133 8137
X5
8105
8104 X5
8103 3
X3 K5
8102
401
K5 *8134 (For DP-8060/8045)
*8147 (For DP-8035)
8610
4
K5
*8134 (For DP-8060/8045)
*8146 (For DP-8035)
H7
8119
H6
8131
5
X5 8132 K9
8115 8227 8129
8144 8125 X8
8108
X3 8122 X5
K5 8138 8124
8116
8145
K6 J6
8117 8118 8123 8144 6
8126
8145
G6
8227
4332
8135 8138
8130
8118 7
8120 8140
8143 2340 8139
K5
G6
Y23 8
Fig. 81 Paper Exit Transportation (2/4)
*8134 (For DP-8060/8045)
*8146 (For DP-8035)
*8147 (For DP-8035)
379
Ver. 1.1 DEC 2006
DP-8060/8045/8035
380
Ver. 1.1 DEC 2006
DP-8060/8045/8035
A B C D E
H7 8136 Y2
8112
401
8148 8111 1
8141
8109 X5 8110
8108 8114
8106
8142
8113 H7
8610 8128 X5
8107
8150 Y26
2
8127 8101 401
X5 4231
8610 8610
8133 8137
X5
8105
8104 X5
8103 3
X3 K5
8102
401
K5 *8134 (For DP-8060/8045)
*8147 (For DP-8035)
8610
4
K5
*8134 (For DP-8060/8045)
*8146 (For DP-8035)
H7
8119
H6
8131
5
X5 8132 K9
8115 8227 8129
8144 8125 X8
8108
X3 8122 X5
K5 8138 8124
8116
8145
K6 J6
8117 8118 8123 8144 6
8126
8145
G6
8227
4332
8135 8138
8130
8118 7
8120 8140
8143 2340 8139
K5
G6
Y23 8
Fig. 81 Paper Exit Transportation (2/4)
*8134 (For DP-8060/8045)
*8146 (For DP-8035)
*8147 (For DP-8035)
381
Ver. 1.1 DEC 2006
DP-8060/8045/8035
382
Ver. 1.1 DEC 2006
DP-8060/8045/8035
A B C D E
(For DP-8035)
8228 8216
8235
X3 8225
8202 X3 1
8201
8203 8228
8205 8231
8204
8206
X3
8202
2
X8 8236
8216
8207 8231 8217
8225
8234
8215 3
8138 X8 8226
8214
8213
8217 8007
X8 8230
8211 8229
8138
4
X8
8122
Y37
8227
J7 8218
5
K5 8219 8209 X5 8123 Y33
X8 8227
8210
8208 Y24
X8 8220
8207 6
8224
8233
X8
8221 H6
X8 7
3510
8222
8
Fig. 82 Paper Exit Transportation (3/4)
383
Ver. 1.1 DEC 2006
DP-8060/8045/8035
384
Ver. 1.1 DEC 2006
DP-8060/8045/8035
A B C D E
X5
2
8316
X5 K6
8301
G6
H6 4332 8313 X5
X3 8302
8309
8303 3
H6
8118
8315
8311
8312
8310 2340
8308 G6
8309
4
8302
8306 8307 8118 H6
8305 H6
8314
X5
8316 5
X5
8304
6
X5
8
Fig. 83 Paper Exit Transportation (4/4)
385
Ver. 1.1 DEC 2006
DP-8060/8045/8035
5.24. PC Boards
386
Ver. 1.1 DEC 2006
DP-8060/8045/8035
A B C D E
1
CN66 CN55
CN57
CN59 (8416)
8413
CN52
CN80
CN61 CN53 CN54
(8417)
8414 8414 4
CN22
8418 CN553 CN554
CN20
CN557
CN21 CN556
CN1
CN551
CN555 CN552
8418 7
CN25
8
Fig. 84 PC Boards (1/4)
387
Ver. 1.1 DEC 2006
DP-8060/8045/8035
PC Boards
388
Ver. 1.1 DEC 2006
DP-8060/8045/8035
A B C D E
1
CN66 CN55
CN57
CN59 (8416)
8413
CN52
CN80
CN61 CN53 CN54
(8417)
8414 8414 4
CN22
8418 CN553 CN554
CN20
CN557
CN21 CN556
CN1
CN551
CN555 CN552
8418 7
CN25
8
Fig. 84 PC Boards (1/4)
389
Ver. 1.1 DEC 2006
DP-8060/8045/8035
PC Boards
390
Ver. 1.1 DEC 2006
DP-8060/8045/8035
A B C D E
SPC (8501)
8504 8505 8506 8414 8414 8507
1
CN709 CN707 CN705 CN703 CN702 CN723
8508
8522 CN706
CN717
8509
(Not mounted) CN708
CN729
CN727 8510
CN722
3
CN721
8520 (Not mounted)
CN728
CN726
8519
8511 4
CN725
CN714
8519
p
CN720
8504
CN701
8508
CN719
8504 CN724 5
CN718 CN713 CN712 CN710 CN711 CN716 8512
8413
8
Fig. 85 PC Boards (2/4)
391
Ver. 1.1 DEC 2006
DP-8060/8045/8035
PC Boards
392
Ver. 1.1 DEC 2006
DP-8060/8045/8035
A B C D E
DRV (8601)
8605 8606 8607 8413
1
CN755 CN753 CN756 CN757 CN767
8616
CN765
8608 OP LVPS (8602)
CN762
8617 8509
8615
CN764
8609
CN758 CN66 CN65 2
8607 CN768
8610
CN763
CN766
CN761 8508
8614
CN760 CN759 4
CN754 CN64
8614 8611
8505 8618
CN752 CN750
CN751
5
CN134
3540 CN662 CN659
8620
8628 7
CN661
CN131
8629
8
Fig. 86 PC Boards (3/4)
393
Ver. 1.1 DEC 2006
DP-8060/8045/8035
PC Boards
394
Ver. 1.1 DEC 2006
DP-8060/8045/8035
A B C D E
DC (8701)
8708 8713 LVPS (8702)
1
CN145 8710 CN3
CN143 CN2
8711 8709
CN144 CN4
8709 CN5
CN142
CN1
8712
2
CN141 8710
CN106
CN101
8714
4
HCE (8715)
CN105
8716
CN108 CN80
CN101
5
CN104 CN103 CN102 CN107
CN81 CN82
CN603
CN172 CN604 7
CN171
CN602 CN601
8
Fig. 87 PC Boards (4/4)
395
Ver. 1.1 DEC 2006
DP-8060/8045/8035
396
Ver. 1.1 DEC 2006
DP-8060/8045/8035
A B C D E
8801
2
8806
J2
J2
Fig.89 - 91
3
8808
4
Y23
8802
5
R1
8803
J2
8804 R1
8807
7
8803
8805
8
Fig. 88 3000-Sheet Tray (LCT) (1/4)
397
Ver. 1.1 DEC 2006
DP-8060/8045/8035
3000-Sheet Tray
398
Ver. 1.1 DEC 2006
DP-8060/8045/8035
A B C D E
X5 1
8408
Y33
8924
8925
8901
R1
G6 8905 2
8903 2340 3
8904
8920 Y22 1123 G6
Y2 Y48
G6
8919
8931 401
8906
4
2843
8928
8908
X5 Y16 8909
8930 Y19
5
R1
Fig.90-91 2841
8918 8907
8910
8917 Y16 8912
Y58 8911
8926
6
8916
Y16
R1 8914
8932 8927
8915
3404 7
8933 Y2
8930 3541
R1
X5
8
Fig. 89 3000-Sheet Tray (LCT) (2/4)
399
Ver. 1.1 DEC 2006
DP-8060/8045/8035
3000-Sheet Tray
400
Ver. 1.1 DEC 2006
DP-8060/8045/8035
A B C D E
Y2
9001
Y2
Y2
1
9029 9030
9025
9039 9002
9003
2
9009
J8 2340
401 9004
9008 X5
9039 9005
9023
9022 9024 3
9008
9031 830 3544
H6 9034
X5
Q1
830
9035 9006
541
K6 J7 9012 1328 4
9028
X5
9021 Y48 8928 9035
9007
9037
4332
Y48 9009
X5 Y2 Y2 9010
9020 5
Q2 9019 9012
9018
X5 Y2 J7 J8
9033
9013 9012
9017 Q1 9023
X5 9009
Y2
9032 6
J8
9026 9011
Q2
9016
Y2
9027
7
9015 9014
Y2
8
Fig. 90 3000-Sheet Tray (LCT) (3/4)
401
Ver. 1.1 DEC 2006
DP-8060/8045/8035
3000-Sheet Tray
402
Ver. 1.1 DEC 2006
DP-8060/8045/8035
A B C D E
Y2
9001
Y2
Y2
1
9029 9030
9025
9039 9002
9003
2
9009
J8 2340
401 9004
9008 X5
9039 9005
9023
9022 9024 3
9008
9031 830 3544
H6 9034
X5
Q1
830
9035 9006
541
K6 J7 9012 1328 4
9028
X5
9021 Y48 8928 9035
9007
9037
4332
Y48 9009
X5 Y2 Y2 9010
9020 5
Q2 9019 9012
9018
X5 Y2 J7 J8
9033
9013 9012
9017 Q1 9023
X5 9009
Y2
9032 6
J8
9026 9011
Q2
9016
Y2
9027
7
9015 9014
Y2
8
Fig. 90 3000-Sheet Tray (LCT) (3/4)
403
Ver. 1.1 DEC 2006
DP-8060/8045/8035
3000-Sheet Tray
404
Ver. 1.1 DEC 2006
DP-8060/8045/8035
A B C D E
Y24
K5 9101
9146 9139
401
9143
9102 H6 X5
9140 2
9104
9134
9133 9105 K5
9106
9103 9111 9138
X3 9117
9135 5
9130 9144 X5 X8
9131
H6
K5
K5 9118
9126 9148 9128 K5
9109 9125
9123 9120 6
9119
9124 X5 9129
9127 9121 H6
X5 9141
X5 H6 7
9142
X5 X8
9122
8
Fig. 91 3000-Sheet Tray (LCT) (4/4)
405
Ver. 1.1 DEC 2006
DP-8060/8045/8035
3000-Sheet Tray
406
Ver. 1.1 DEC 2006
DP-8060/8045/8035
A B C D E
Y24
K5 9101
9146 9139
401
9143
9102 H6 X5
9140 2
9104
9134
9133 9105 K5
9106
9103 9111 9138
X3 9117
9135 5
9130 9144 X5 X8
9131
H6
K5
K5 9118
9126 9148 9128 K5
9109 9125
9123 9120 6
9119
9124 X5 9129
9127 9121 H6
X5 9141
X5 H6 7
9142
X5 X8
9122
8
Fig. 91 3000-Sheet Tray (LCT) (4/4)
407
Ver. 1.1 DEC 2006
DP-8060/8045/8035
408
Ver. 1.1 DEC 2006
DP-8060/8045/8035
A B C D E
K8
Y2
9201 2
9210 Y2
9202
9203 Y2
3
9204
9205 9019
Y2
9206
9033
8918 4
9209 9032
X5
9207
Y2 9205 5
9208
8
Fig. 92 Letter-R / Legal Size Adapter (LCT)
409
Ver. 1.1 DEC 2006
DP-8060/8045/8035
410
Ver. 1.1 DEC 2006
DP-8060/8045/8035
A B C D E
9305
J7 1
2907
X3
9324 2902
9301
S6 Y19 9302 2904
9303 2905
2
2914 2904
2909
J7
2910 9304
G6
9306
2915
X8 X8
K9 2909
9307 Y19 2911 2915 3
9307
9035 9323 S6 2910
Y19
9318
9308 9319 S6
Y40 8002
Y19
Y19
Y19 K5 4
3918
3920
3919
9308 Y19
Y40
5
Y19 9325
Y19
Y40 9321
3917
Y40 J6
S6 Y19 3815
9309 9320 9325 9317
Y19
J6 3815 6
3916
3916 Y19 S6
9322 9316
X5 9310
9311
7
9314
9315
Y19
9312
X8
9313
8
Fig. 93 System Console (1/2)
411
Ver. 1.1 DEC 2006
DP-8060/8045/8035
System Console
412
Ver. 1.1 DEC 2006
DP-8060/8045/8035
A B C D E
H6 H6
9404 9405
9403
208 9408
9401 9407 1
X5 Y19 9402 208
9403 3105
9405 9406
J7 9431
208
9430 4023
541 9409 4024
9410
Y19 4001 2
9411
830 9429 X5 Y26
541 4006
9426
208
Y19 9412 X5
2813 4007
8614 4005 4025
9413 3
H6 1709 4029
9414
4026
9416 4002 4003 X5
4004
9417 H6 Y19
3011 9424
K5 X5 4
3001
X5 4008 Y19
401 Y19 2603
9039
9415
3002
G6
3010 5
401 Y19 822
9432
9039 9421 X5
401
X5
9423
9419 401
8707
9427 6
8927 X5
9418
9429
9433
Y19
7
9420 9425
8807
Y19
9428
Y19 8
Fig. 94 System Console (2/2)
413
Ver. 1.1 DEC 2006
DP-8060/8045/8035
System Console
414
Ver. 1.1 DEC 2006
DP-8060/8045/8035
A B C D E
H6 H6
9404 9405
9403
208 9408
9401 9407 1
X5 Y19 9402 208
9403 3105
9405 9406
J7 9431
208
9430 4023
541 9409 4024
9410
Y19 4001 2
9411
830 9429 X5 Y26
541 4006
9426
208
Y19 9412 X5
2813 4007
8614 4005 4025
9413 3
H6 1709 4029
9414
4026
9416 4002 4003 X5
4004
9417 H6 Y19
3011 9424
K5 X5 4
3001
X5 4008 Y19
401 Y19 2603
9039
9415
3002
G6
5
401 Y19 3010 822
9039 9421 X5
401
X5
9423
9419 401
8707
9427 6
8927 X5
9418
9429
Y19
7
9420 9425
8807
Y19
9428
Y19 8
Fig. 94 System Console (2/2)
415
Ver. 1.1 DEC 2006
DP-8060/8045/8035
J6 XUC3VM E-Ring
J7 XUC4VM E-Ring
J8 XUC7VM E-Ring
416
Ver. 1.1 DEC 2006
DP-8060/8045/8035
K5 XUC5VM E-Ring
K6 XUC6VM E-Ring
L2 XUC9VM E-Ring
L5 FFPFA01461 Screw
L7 XUC2VM E-Ring
417
Ver. 1.1 DEC 2006
DP-8060/8045/8035
N7 FFPFA01591 Screw
N8 FFPFA01471 Screw
P4 PF2217P319A Screw
P7 FFPFA0152 Screw
418
Ver. 1.1 DEC 2006
DP-8060/8045/8035
419
Ver. 1.1 DEC 2006
DP-8060/8045/8035
420
Ver. 1.1 DEC 2006
DP-8060/8045/8035
421
Ver. 1.1 DEC 2006
DP-8060/8045/8035
memo
422
Ver. 1.1 DEC 2006
DP-8060/8045/8035
Center Feeder 3
Assembly (Fig. F10)
Inlet Feeder
Assembly (Fig. F12)
Finisher Controller
PCB Assembly (Fig. F24) 5
8
Fig. F01 Assembly Location Diagram (1/3)
423
Ver. 1.1 DEC 2006
DP-8060/8045/8035
A B C D E
Swing Guide 1
Assembly (Fig. F14)
Stapler Tray
Assembly (Fig. F15) 2
Swing
Assembly (Fig. F13)
Tray Frame
Assembly (Fig. F06)
5
Stapler
Assembly (Fig. F16)
Tray Drive
Assembly (Fig. F07)
8
Fig. F01 Assembly Location Diagram (2/3)
424
Ver. 1.1 DEC 2006
DP-8060/8045/8035
A B C D E
Saddle
Assembly
(Fig. F17)
Saddle Delivery
Assembly (Fig. F22)
4
Stapler
Assembly (Fig. F19)
Saddle Controller
PCB Assembly (Fig. F25)
Saddle Guide
Assembly (Fig. F18) 6
Motor Mount
Assembly (Fig. F23)
7
Pass Lower Guide
Assembly (Fig. F20)
8
Fig. F01 Assembly Location Diagram (3/3)
425
Ver. 1.1 DEC 2006
DP-8060/8045/8035
426
Ver. 1.1 DEC 2006
DP-8060/8045/8035
A B C D E
5013
5008
5010
5025
5017
5020
5023 5021
5020 5022 3
5012
5010
5011
5007
5026 5020
4
5027
5007
5006
5020
5005
5018 5
6
B B
5015
B
5024
8
Fig. F02 Attachment Parts
427
Ver. 1.1 DEC 2006
DP-8060/8045/8035
428
Ver. 1.1 DEC 2006
DP-8060/8045/8035
A B C D E
5103 1
5150
5178 5102
5177
(J1010) 5138
(J1020)
5158
2
5159 (J201)
(J101) 5167 x 5
(PI11) (J102) 5156 5165 5139
(PI12) 5157 5168
5174
(J1010)
(J1020)
5168 3
5160
5140
5152
5151
5154
5169 5101
5142
5128 4
5122
5167 x 3 5173
5128
5129
5133 5133
5
5168
5123
5180 5125
5130
5130 6
5127
5124
5126
5172
5134
5182 (MS4)
(J118) 7
(PI5)
5131 (J118)
5171
5168 5132 (J206) (J205)
5167
5166
8
Fig. F03 External Covers, Panels, etc. (1/2)
429
Ver. 1.1 DEC 2006
DP-8060/8045/8035
430
Ver. 1.1 DEC 2006
DP-8060/8045/8035
A B C D E
5110 5143
5115
5106 2
5175
5161 (PI6) 5107
(J100)
5176
5105 5111
(J502)
5121
5118 5119
5181 5146 5168
5120 3
5113 5114 5117
5183
5116
5135 5020 x 3
5175
5104
5145 5112 5020 5167 4
5184
5144
5108 5020 5147
5020
5162 5164 5108 5020 5109 5
5137 5136
5141 5020 x 2
5167
5020 x 4
5175 6
5149
5163
5175 5155 5153
7
5148 5020 x 4
8
Fig. F03 External Covers, Panels, etc. (2/2)
431
Ver. 1.1 DEC 2006
DP-8060/8045/8035
432
Ver. 1.1 DEC 2006
DP-8060/8045/8035
A B C D E
5240
5020
5226
5211 (JS1)
5020
5238 See Fig. F05
5020 5205
5206 5211 7
5020
5202 2-Bin Saddle-Stitch Finisher
5020
2-Bin Saddle-Stitch
Finisher
8
Fig. F04 Finisher Main Body (1/2)
433
Ver. 1.1 DEC 2006
DP-8060/8045/8035
434
Ver. 1.1 DEC 2006
DP-8060/8045/8035
A B C D E
5203
5020 5209
5020 5204 5229
5235 2
5020
5248 (MS5)
5020
5230 (J132)
5212 5234
5020 3
5232
5210
(J131)
5213 (MS3)
5020 5231
5020 5225
5224 4
(PI8)
(J130)
5217
5214 5
5020
5207 See Fig. F17 (J3)
(J400)
(J19)
(J500)
5219
5020
6
5221
5233
5216 5220
5020
5233 7
5223
5222
2-Bin Saddle-Stitch Finisher
2-Bin Saddle-Stitch Finisher
8
Fig. F04 Finisher Main Body (2/2)
435
Ver. 1.1 DEC 2006
DP-8060/8045/8035
436
Ver. 1.1 DEC 2006
DP-8060/8045/8035
A B C D E
5309 3
5302
5303 5313
5304
5311
2-Bin Saddle-Stitch 2-Bin Saddle-Stitch
Finisher Finisher
5310
5312 (JS1)
8
Fig. F05 Harness Main Body Assembly
437
Ver. 1.1 DEC 2006
DP-8060/8045/8035
438
Ver. 1.1 DEC 2006
DP-8060/8045/8035
A B C D E
5411 5413
5407
5172
5403
3
4
5413 5407
5411
5402
5411
5409
5413
5401 5404 5410
5
5411
5405
5413 5410
5413
5406
5413 5406 6
8
Fig. F06 Tray Frame Assembly
439
Ver. 1.1 DEC 2006
DP-8060/8045/8035
440
Ver. 1.1 DEC 2006
DP-8060/8045/8035
A B C D E
5505 5509
3
5504
5511 5504
5502
5512
5515 5508
5503 4
5506
5236
5509 (J400)
(PI9)
5505 (PI19)
(M5)
5501
5
5513
5236
5504 5514 (J115) 5507
5511
6
8
Fig. F07 Tray Drive Assembly
441
Ver. 1.1 DEC 2006
DP-8060/8045/8035
442
Ver. 1.1 DEC 2006
DP-8060/8045/8035
A B C D E
5603
5608
5601
(J16)
5602 3
(M8)
5603
5604
5614
(M1)
4
5236
5609 (J10)
5605
5612
5610 5613
5
5607
5609
5606
6
8
Fig. F08 Feeder Drive Assembly
Note:
This assembly is included in the assembly shown in Figure F09.
443
Ver. 1.1 DEC 2006
DP-8060/8045/8035
444
Ver. 1.1 DEC 2006
DP-8060/8045/8035
A B C D E
5746
5748
(J113T)
(J112T)
(J114)
5761 (J113) 5020 See Fig. F08 5717 2
5764
5765 (J6)
5020 5020
5750
4
5736
5702
5715
5020 5735
(PI15)
5706 (J117)
5
5704 5719
5020 5711
5763
5762
(PI16)
5763 6
(J113) 5719 5714
5705 5722
(MS1) 5413
5703
See Fig. F12
(J112)
7
5713
5020
8
Fig. F09 Feeder Assembly (1/2)
Note:
1.This assembly includes the assemblies shown in Figures F08, F10, F11, and F12.
2.This assembly does not include the parts shown with key No. 5747, and 5751.
445
Ver. 1.1 DEC 2006
DP-8060/8045/8035
Feeder Assembly
446
Ver. 1.1 DEC 2006
DP-8060/8045/8035
A B C D E
1
5726
(SL2)
5172 (J108)
5747
5758
5718
2-Bin (SL1) 2
Saddle-Stitch
Finisher 5751
5736
5172 (J107)
5727
5020 2-Bin
Saddle-Stitch
5721 Finisher
5707 2-Bin 3
5737 2-Bin Saddle-Stitch
Saddle-Stitch Finisher
Finisher 5738 2-Bin Saddle-Stitch
5721 Finisher
5735 A
5723
5721
4
5739
5740
5724
5733 A
5725 5
5020
2-Bin
Saddle- 5734
5710
Stitch 5745
Finisher 5746
5728
5731
(J600)
5741 6
5020 5172
5742 5743
5020 5732 5730
5758
5729 5744
(J600)
(SL7)
(J600)
7
5731 5753
5020 5712
5743 5172
5172 (J500)
5746
8
Fig. F09 Feeder Assembly (2/2)
447
Ver. 1.1 DEC 2006
DP-8060/8045/8035
448
Ver. 1.1 DEC 2006
DP-8060/8045/8035
A B C D E
5800
5827
5813
5413
5827
5814
5413 2
5827
5813
5801 5413
5413
5833
5834 5812
3
5827
5813 5816
5413 5707 5806
5819 5827
5814
5413 5835
5413
5827
5813 5815 4
5413 5829
5825
5808 5821
5836
5832 5804
5807
5823
5824 5
(SL3) 5820
5413
5809 5802
5803
(J109)
5830
5172
6
5830
(J24)
(J110)
(J110) (PI14)
5822
(J109)
5805
(J105) 7
5810
5811
5169 5817
8
Fig. F10 Center Feeder Assembly
Note:
This assembly is included in the assembly shown in Figure F09.
449
Ver. 1.1 DEC 2006
DP-8060/8045/8035
450
Ver. 1.1 DEC 2006
DP-8060/8045/8035
A B C D E
5900 5906
1
5904
5169 5803
5906 5921
5927
5909
5916 5169
5817
5830 2
5169 5901
5916
5902 5914
5913
5830
4
(PI17) 5928
(J105) 5918
5926 5912
5923
5172
5911
5906 5910
5907 5
5904
5803
5830
5906 5921
5925
5924 5908
5817 6
5903
5917
8
Fig. F11 Buffer Upper Guide Assembly
Note:
This assembly is included in the assembly shown in Figure F09.
451
Ver. 1.1 DEC 2006
DP-8060/8045/8035
452
Ver. 1.1 DEC 2006
DP-8060/8045/8035
A B C D E
6000 1
5411
6031 6030
5413
2
6015
5411
6029 6027
6003 5411
5411
5763
5511 (PI1) 5835 5411 4
(J106) 6008
6017
5411
5175 6032
6021 6019
6020 5411 (J502)
5
5824
5413
6007 (M9)
6
6006 6016
5175
(J502)
(J106) (J202)
6005
6010
6009
7
8
Fig. F12 Inlet Feeder Assembly
Note:
This assembly is included in the assembly shown in Figure F09.
453
Ver. 1.1 DEC 2006
DP-8060/8045/8035
454
Ver. 1.1 DEC 2006
DP-8060/8045/8035
A B C D E
5172
See Fig. F14
6124 6147
(MS2) 5172
(MS6)
6103
5413 (J209)
6143
6120 6107
6122 6137
5827 (PI18) 3
6106
(J127) 6108
6109
See Fig. F15 6110 C
(J204)
6119
C 4
5172
6135
A 6118
6101
6128
6116
6115
6102 6145
6102
5
6116 6146
6014 (J207) 5827
5413 6121 5172
6125 5413 6113
6117
6129 6134 (J134)
(J124) (PI3)
(J121) (J122) 6130
(J128) 6
6133 B
(J125) (J120) 6131 (J208)
(J123) 6112
6126 B 6142 6113 5168
6127
5172 A
6111
5172 6105 6114
6123 6104 7
(J134)
(J501) (J119)
6132
8
Fig. F13 Swing Assembly
455
Ver. 1.1 DEC 2006
DP-8060/8045/8035
456
Ver. 1.1 DEC 2006
DP-8060/8045/8035
A B C D E
1
6220
6215
5168 6217
6206
6204
6215 6242 6252
6245 6216
6203 6207
6202
6246 2
6242 6244
6245
6201
6223 6236
6243 5167
6219
6204 B
6244 6251 6225 3
6216
6226
6229
6231
6235 6234
6230 6233 C
A 6250 6233
6212 6211
5
6232 5127 5127
6212
6247
B
6211 5413
A 6224
6210 6247
6210
(J128) 6208 6
6221
5172 (SL5) 6205 5413
5168
6224
5827
6213
5413 6214
5413 7
5168
6218
6222
8
Fig. F14 Swing Guide Assembly
457
Ver. 1.1 DEC 2006
DP-8060/8045/8035
458
Ver. 1.1 DEC 2006
DP-8060/8045/8035
A B C D E
1
5413 6338
6313
6351
6222
6323
5758
6337
6106 2
5413
6335
6367 6335 5413
6368 6324
5413
6343
6322 3
6344
5413
6301 6330
(M7)
5758
6316
(J124) 6319 4
6332 6321
6303
(J501) 5172
(M2)
5413
6317 5172
5413
6346 6315 5
6318
5758
A
6369
B
6334
6307 6302 6329 A
6329 6339 6333 6350
B
6
6314
5168
6336
6370 6355
6336 6372
6311 6325
6355 6310 7
5168
6309
6355
6325 6311
6371
5758
8
Fig. F15 Stapler Tray Assembly (1/2)
459
Ver. 1.1 DEC 2006
DP-8060/8045/8035
460
Ver. 1.1 DEC 2006
DP-8060/8045/8035
A B C D E
5172
5172 1
5172
6304 6308 2
(PI6)
(J121)
6331
6327
6306
(SL6)
6362
4
(J123)
6361
6348
6359 6360 5
6328
6320
6364
5172 6349
6341
5835 (PI10)
(J120) 6
6366
6345 6341
(PI20)
(J125)
(J119)
5168
(M3) 7
6340
5172
6357
6358
6305
6326
8
Fig. F15 Stapler Tray Assembly (2/2)
461
Ver. 1.1 DEC 2006
DP-8060/8045/8035
462
Ver. 1.1 DEC 2006
DP-8060/8045/8035
A B C D E
1
6436
6442
5236 6429
6415
6401
6428 6419
6420
2
(M6) 6416
6435 6417 6418
6430 6421
5172 6419
5236 6420 3
5176
6408 6422
(M4)
6444
(J304) 6407
6409 (J306) 5236
6423
6412
6406 6426 4
6409
6412
5236 6431 6402
6431
6409
6409
5
6405 6410
6411 6403
6424 6425
(J210)
6427 (J129)
6443
7
(PI7)
6432 6432
8
Fig. F16 Stapler Assembly
463
Ver. 1.1 DEC 2006
DP-8060/8045/8035
464
Ver. 1.1 DEC 2006
DP-8060/8045/8035
A B C D E
6588
5413
65067 A
65033
65068 65051 A
65022
6575 65002 6586 5
65016
6597 65003 5413
65033
6581
65062 65017
65041 65004
6557 6
5824 6562
6594 6541 5172
5246
5234
(M1) 5020
(J115)
See Fig. F23 65042 7
5020
8
Fig. F17 Saddle Assembly (2-Bin Saddle-Stitch Finisher) (1/4)
465
Ver. 1.1 DEC 2006
DP-8060/8045/8035
466
Ver. 1.1 DEC 2006
DP-8060/8045/8035
A B C D E
1
6517 5236
(MS1)
See Fig. F18 (J109)
6502
6512
(PI9)
(J124) 6580 2
6523
5413
6014
6509
5236
(PI12)
(JD1) (J126)
5020
3
6502 6512
6517 5236 65056
(MS2) (PI15)
(J110) (J129) 6512
65015 6518
(PI2) 5236 6512
(PI14) 5020
(J104) (J128)
6512
5725 4
5020 (PI13) 5020
(J127)
6539
5824
5413 6512
6512 5236 65059
(PI3) See Fig. F20
(J103) (MS3)
(J111) 6599
5
6538
5020
6517 5020
6502
6510 (J111) 6599
5020 (J305)
(J103) 6537
(J303)
6
6551
6552
65012
65057
65058
6351 65019
5020
8
Fig. F17 Saddle Assembly (2-Bin Saddle-Stitch Finisher) (2/4)
467
Ver. 1.1 DEC 2006
DP-8060/8045/8035
468
Ver. 1.1 DEC 2006
DP-8060/8045/8035
A B C D E
5835 6521
B 6545
6
65068 6524 5413
6014
5413 65067
6524 65008
65060
6522
6014 5246 7
5413
6574
6535
8
Fig. F17 Saddle Assembly (2-Bin Saddle-Stitch Finisher) (3/4)
469
Ver. 1.1 DEC 2006
DP-8060/8045/8035
470
Ver. 1.1 DEC 2006
DP-8060/8045/8035
A B C D E
5835 6521
B 6545
6
65068 6524 5413
6014
5413 65067
6524 65008
65060
6522
6014 5246 7
5413
6574
6535
8
Fig. F17 Saddle Assembly (2-Bin Saddle-Stitch Finisher) (3/4)
471
Ver. 1.1 DEC 2006
DP-8060/8045/8035
472
Ver. 1.1 DEC 2006
DP-8060/8045/8035
A B C D E
1
65070
6530
6576
6529 65066 6568
6503
6505
6558 2
(PI18) 5236
5236 (PI19)
(PI20)
(J304) 6554
(J123)
See Fig. F19 C 6553
5511
6569 5504
6532
6570 6583 6504 5178 6577 3
5174 6506
6590 6560
65040
5511
5504
5835 65032
6540 6577 5511
65024
6508
6572 4
65034 5172
5020 5020 5504
6561
6520
6520 65001 (M3)
5413
C 65011 6556
(J119)
6591 6555
5020 5
(J132) (J308) 65045 5020
6560 65011 5020
6506 65051
65018 5020
6577 (PI17)
5020 (J115)
(J132) 6592
6592
6577 6512
65032 6
5504 6587 6596
5511 5504
65034
6595 65055
5511 65013 5835
6532
5504
5511 5246
5413 5236 7
5758
65014
6549 See Fig. F25
6550
8
Fig. F17 Saddle Assembly (2-Bin Saddle-Stitch Finisher) (4/4)
473
Ver. 1.1 DEC 2006
DP-8060/8045/8035
474
Ver. 1.1 DEC 2006
DP-8060/8045/8035
A B C D E
1
65070
6530
6576
6529 65066 6568
6503
6505
6558 2
(PI18) 5236
5236 (PI19)
(PI20)
(J304) 6554
(J123)
See Fig. F19 C 6553
5511
6569 5504
6532
6570 6583 6504 5178 6577 3
5174 6506
6590 6560
65040
5511
5504
5835 65032
6540 6577 5511
65024
6508
6572 4
65034 5172
5020 5020 5504
6561
6520
6520 65001 (M3)
5413
C 65011 6556
(J119)
6591 6555
5020 5
(J132) (J308) 65045 5020
6560 65011 5020
6506 65051
65018 5020
6577 (PI17)
5020 (J115)
(J132) 6592
6592
6577 6512
65032 6
5504 6587 6596
5511 5504
65034
6595 65055
5511 65013 5835
6532
5504
5511 5246
5413 5236 7
5758
65014
6549 See Fig. F25
6550
8
Fig. F17 Saddle Assembly (2-Bin Saddle-Stitch Finisher) (4/4)
475
Ver. 1.1 DEC 2006
DP-8060/8045/8035
476
Ver. 1.1 DEC 2006
DP-8060/8045/8035
A B C D E
6616 5236
6605
6614
6603
4
6602
5172
5411
6607
6601
6615
6606 6608
6604
6611 5
6613
5236
8
Fig. F18 Saddle Guide Assembly (2-Bin Saddle-Stitch Finisher)
477
Ver. 1.1 DEC 2006
DP-8060/8045/8035
478
Ver. 1.1 DEC 2006
DP-8060/8045/8035
A B C D E
6738
5020
6713 6715
5020 (J306)
(J305) 2
6701 6033 (JD2)
6716
6707 6731 6718 (J315) 5511
5174 5835 x 4 B (J316)
6709 A
6727
6701
6710 6716 3
6717 5020
5174
A
6705 5020
6728 6719
(M7) (M6) 6706 5020 6706
(MS6) (MS4) 6704
6575
(MS7) (MS5)
(J315)(J316) 5174 B 4
5020
5020
6723
6720
5174
6703
5020
6729 5
6702
6732
5020
6
6737 6708
6730
5020 5020
6722
6726 7
6711
6712 5020
8
Fig. F19 Stapler Assembly (2-Bin Saddle-Stitch Finisher)
479
Ver. 1.1 DEC 2006
DP-8060/8045/8035
480
Ver. 1.1 DEC 2006
DP-8060/8045/8035
A B C D E
5020
6815 2
6808
6813
6807
6811
6812
6823
6805
6599
4
5413
6810
6818
5020
(PI5)
6802 (J101)
6803
(J309) (J113) 5
(J302)
6804 (J101) 6817 6809
5413 6822 (M5)
5835
(J225) 6561 5172
6805
5020 6599
65052 6
6801 (PI7)
6816
(J106)
6818 5246
(J402)
(J325) 7
6802
6804
8
Fig. F20 Pass Lower Guide Assembly (2-Bin Saddle-Stitch Finisher)
481
Ver. 1.1 DEC 2006
DP-8060/8045/8035
482
Ver. 1.1 DEC 2006
DP-8060/8045/8035
A B C D E
6914
6915
2
6903 6912
6910
6904 6915
6914
(J301)
6589 (J105)
6906
3
6907 65052 5413
6916
6923
(PI8) (J105)
6908
5236 6913
(M4) 5236
4
6910 6909 (J114) 6902
6924
6918
6908
5236 5413
6922
5413
5835
6905 5
6918
6925
6911
5413
6911
7
8
Fig. F21 Inner Side Plate Assembly (2-Bin Saddle-Stitch Finisher)
483
Ver. 1.1 DEC 2006
DP-8060/8045/8035
484
Ver. 1.1 DEC 2006
DP-8060/8045/8035
A B C D E
7023
7010
7027
2
7023
7019
5413
7002 5824
7005 3
7003
7004
4
7029
5124
7028
7030
7020
7001
5
6014 7026
5413
7017
7009
7024 6
7007
7008 7024
(J525)
7011
7018
7021 (PI11)
5816
7006 7023
7001 7
5413 7016 7010 7012 (J425) 7013
8
Fig. F22 Saddle Delivery Assembly (2-Bin Saddle-Stitch Finisher)
Note:
This assembly does not include the part shown with key No. 7021.
485
Ver. 1.1 DEC 2006
DP-8060/8045/8035
486
Ver. 1.1 DEC 2006
DP-8060/8045/8035
A B C D E
7103
7114 7113
7119 3
7106
7115 (M2)
7124 7109
7119
7112 7119
5511 (J112)
7111 7107
5511 (J108)
4
65050
5020
7102 (M8)
7110 7104
5511
7120
(PI4) (PI1)
(J102) (J107)
5
5411
7105 7105
5411
5020 7123
7122
7102 7119
7110 7108
5511 7101 6
8
Fig. F23 Motor Mount Assembly (2-Bin Saddle-Stitch Finisher)
487
Ver. 1.1 DEC 2006
DP-8060/8045/8035
488
Ver. 1.1 DEC 2006
DP-8060/8045/8035
A B C D E
(Q007)
7201
6
8
Fig. F24 Finisher Controller PCB Assembly
489
Ver. 1.1 DEC 2006
DP-8060/8045/8035
490
Ver. 1.1 DEC 2006
DP-8060/8045/8035
A B C D E
(Q002)
7301
8
Fig. F25 Saddle Controller PCB Assembly (2-Bin Saddle-Stitch Unit)
491
Ver. 1.1 DEC 2006
DP-8060/8045/8035
492
Ver. 1.1 DEC 2006
DP-8060/8045/8035
A B C D E
2
J112T
J6
J113T J2
J12
J132
J114 J24
J209 J17 3
J105 J110 J1 J202
J5
J109
J7
J113
J130 J131
J140
J112 4
J118
J206 JS1
J205
J502
J202
6
J106
8
Fig. F26 List of Connectors (1/4)
493
Ver. 1.1 DEC 2006
DP-8060/8045/8035
List of Connectors
494
Ver. 1.1 DEC 2006
DP-8060/8045/8035
A B C D E
2
J112T
J6
J113T J2
J12
J132
J114 J24
J209 J17 3
J105 J110 J1 J202
J5
J109
J7
J113
J130 J131
J140
J112 4
J118
J206 JS1
J205
J502
J202
6
J106
8
Fig. F26 List of Connectors (1/4)
495
Ver. 1.1 DEC 2006
DP-8060/8045/8035
List of Connectors
496
Ver. 1.1 DEC 2006
DP-8060/8045/8035
A B C D E
2
J112T
J6
J113T J2
J12
J132
J114 J24
J209 J17 3
J105 J110 J1 J202
J5
J109
J7
J113
J130 J131
J140
J112 4
J118
J206 JS1
J205
J502
J202
6
J106
8
Fig. F26 List of Connectors (1/4)
497
Ver. 1.1 DEC 2006
DP-8060/8045/8035
List of Connectors
498
Ver. 1.1 DEC 2006
DP-8060/8045/8035
A B C D E
J16
J9 1
J204 J14
J207
J208
J11 J12
J8
J10
2
J7
J500
J600 J301
J107
J108
J400 J117
3
J204 J210
J207 J206 J115 J201
J122 J208 J205
J134 J127
J501
J128 J121
4
J124
J120 J1010
J125
J123 J101 J210
J119 J306 J304
J1020 5
J129 J302
J307 J305 J201
J102
8
Fig. F26 List of Connectors (2/4)
499
Ver. 1.1 DEC 2006
DP-8060/8045/8035
List of Connectors
500
Ver. 1.1 DEC 2006
DP-8060/8045/8035
A B C D E
J16
J9 1
J204 J14
J207
J208
J11 J12
J8
J10
2
J7
J500
J600 J301
J107
J108
J400 J117
3
J204 J210
J207 J206 J115 J201
J122 J208 J205
J134 J127
J501
J128 J121
4
J124
J120 J1010
J125
J123 J101 J210
J119 J306 J304
J1020 5
J129 J302
J307 J305 J201
J102
8
Fig. F26 List of Connectors (2/4)
501
Ver. 1.1 DEC 2006
DP-8060/8045/8035
List of Connectors
502
Ver. 1.1 DEC 2006
DP-8060/8045/8035
A B C D E
J16
J9 1
J204 J14
J207
J208
J11 J12
J8
J10
2
J7
J500
J600 J301
J107
J108
J400 J117
3
J204 J210
J207 J206 J115 J201
J122 J208 J205
J134 J127
J501
J128 J121
4
J124
J120 J1010
J125
J123 J101 J210
J119 J306 J304
J1020 5
J129 J302
J307 J305 J201
J102
8
Fig. F26 List of Connectors (2/4)
503
Ver. 1.1 DEC 2006
DP-8060/8045/8035
List of Connectors
504
Ver. 1.1 DEC 2006
DP-8060/8045/8035
A B C D E
J16
J9 1
J204 J14
J207
J208
J11 J12
J8
J10
2
J7
J500
J600 J301
J107
J108
J400 J117
3
J204 J210
J207 J206 J115 J201
J122 J208 J205
J134 J127
J501
J128 J121
4
J124
J120 J1010
J125
J123 J101 J210
J119 J306 J304
J1020 5
J129 J302
J307 J305 J201
J102
8
Fig. F26 List of Connectors (2/4)
505
Ver. 1.1 DEC 2006
DP-8060/8045/8035
List of Connectors
506
Ver. 1.1 DEC 2006
DP-8060/8045/8035
A B C D E
J3 J18
J19
J21
J23
3
J400 J204
J304
J500
J131 4
J123 J109
JD1
J124 J120
J121
J316 J116
JD2
J110 J306 J114 5
J315
J305
J126 J119
J104
J127
J13 J10
J112 J2
J101 J11 6
J7 J9
J108 J4
J12
J15
J8
J1
7
J209
J309
8
Fig. F26 List of Connectors (3/4)
507
Ver. 1.1 DEC 2006
DP-8060/8045/8035
List of Connectors
508
Ver. 1.1 DEC 2006
DP-8060/8045/8035
A B C D E
J3 J18
J19
J21
J23
3
J400 J204
J304
J500
J131 4
J123 J109
JD1
J124 J120
J121
J316 J116
JD2
J110 J306 J114 5
J315
J305
J126 J119
J104
J127
J13 J10
J112 J2
J101 J11 6
J7 J9
J108 J4
J12
J15
J8
J1
7
J209
J309
8
Fig. F26 List of Connectors (3/4)
509
Ver. 1.1 DEC 2006
DP-8060/8045/8035
List of Connectors
510
Ver. 1.1 DEC 2006
DP-8060/8045/8035
A B C D E
J3 J18
J19
J21
J23
3
J400 J204
J304
J500
J131 4
J123 J109
JD1
J124 J120
J121
J316 J116
JD2
J110 J306 J114 5
J315
J305
J126 J119
J104
J127
J13 J10
J112 J2
J101 J11 6
J7 J9
J108 J4
J12
J15
J8
J1
7
J209
J309
8
Fig. F26 List of Connectors (3/4)
511
Ver. 1.1 DEC 2006
DP-8060/8045/8035
List of Connectors
512
Ver. 1.1 DEC 2006
DP-8060/8045/8035
A B C D E
J3 J18
J19
J21
J23
3
J400 J204
J304
J500
J131 4
J123 J109
JD1
J124 J120
J121
J316 J116
JD2
J110 J306 J114 5
J315
J305
J126 J119
J104
J127
J13 J10
J112 J2
J101 J11 6
J7 J9
J108 J4
J12
J15
J8
J1
7
J209
J309
8
Fig. F26 List of Connectors (3/4)
513
Ver. 1.1 DEC 2006
DP-8060/8045/8035
List of Connectors
514
Ver. 1.1 DEC 2006
DP-8060/8045/8035
A B C D E
J118
J117
J208
J130
J128 5
J132 J308
J525 J115
J100 J18
J425 J105 J129
J502 J125 J11
J402 J301 J113 J9
J201 J13
J6 6
J103 J7
J225 J325 J4
J106
J111 J102
J5
J305 J107
J15
J303
J203 7
J205 J202
J302
8
Fig. F26 List of Connectors (4/4)
515
Ver. 1.1 DEC 2006
DP-8060/8045/8035
List of Connectors
516
Ver. 1.1 DEC 2006
DP-8060/8045/8035
A B C D E
J118
J117
J208
J130
J128 5
J132 J308
J525 J115
J100 J18
J425 J105 J129
J502 J125 J11
J402 J301 J113 J9
J201 J13
J6 6
J103 J7
J225 J325 J4
J106
J111 J102
J5
J305 J107
J15
J303
J203 7
J205 J202
J302
8
Fig. F26 List of Connectors (4/4)
517
Ver. 1.1 DEC 2006
DP-8060/8045/8035
List of Connectors
518
Ver. 1.1 DEC 2006
DP-8060/8045/8035
A B C D E
J118
J117
J208
J130
J128 5
J132 J308
J525 J115
J100 J18
J425 J105 J129
J502 J125 J11
J402 J301 J113 J9
J201 J13
J6 6
J103 J7
J225 J325 J4
J106
J111 J102
J5
J305 J107
J15
J303
J203 7
J205 J202
J302
8
Fig. F26 List of Connectors (4/4)
519
Ver. 1.1 DEC 2006
DP-8060/8045/8035
List of Connectors
520
Ver. 1.1 DEC 2006
DP-8060/8045/8035
A B C D E
J118
J117
J208
J130
J128 5
J132 J308
J525 J115
J100 J18
J425 J105 J129
J502 J125 J11
J402 J301 J113 J9
J201 J13
J6 6
J103 J7
J225 J325 J4
J106
J111 J102
J5
J305 J107
J15
J303
J203 7
J205 J202
J302
8
Fig. F26 List of Connectors (4/4)
521
Ver. 1.1 DEC 2006
DP-8060/8045/8035
memo
522
Ver. 1.1 DEC 2006
DP-8060/8045/8035
Punch Slide
Assembly (Fig. P04)
6
8
Fig. P01 Assembly Location Diagram
523
Ver. 1.1 DEC 2006
DP-8060/8045/8035
524
Ver. 1.1 DEC 2006
DP-8060/8045/8035
A B C D E
7406
(J21)
(J3)
(J23)
7404 (J4)
2
5167
7405
5167
7403
4
5167
7403
5026
5411
7401
5027
5
7402
8
Fig. P02 Attachment Parts
525
Ver. 1.1 DEC 2006
DP-8060/8045/8035
526
Ver. 1.1 DEC 2006
DP-8060/8045/8035
A B C D E
1
(J114)
7506
(J104)
(J1)
7505 (J110) (J102) (J2)
(J111) (J105) (J5)
(J7)
(J101) 2
See Fig. P04
7537 7508
5167 7509
7516 (J112)
7537
7509 7507
5020 (J106)
7502 5020 3
5411
5413 7519 (J106) See Fig. P05
7546 (PI1)
(J102) 7551
5236 7515
7512
7524 4
5020
7549
(M2)
7552
7553 (J101)
7525 5020
6008
7550 5236 5411
7533 (MS1) (J112)
5
7521 (J106)
7538 5020
7513
7518 7527 5169
(MS2) 5171
7522 (J106) 5511
5411 7526
7513 7548 7517
7523 7518
5020 5171 7532 6
7504 7529
5144
8
Fig. P03 Punch Main Body
527
Ver. 1.1 DEC 2006
DP-8060/8045/8035
List of Connectors
528
Ver. 1.1 DEC 2006
DP-8060/8045/8035
A B C D E
1
(J114)
7506
(J104)
(J1)
7505 (J110) (J102) (J2)
(J111) (J105) (J5)
(J7)
(J101) 2
See Fig. P04
7537 7508
5167 7509
7516 (J112)
7537
7509 7507
5020 (J106)
7502 5020 3
5411
5413 7519 (J106) See Fig. P05
7546 (PI1)
(J102) 7551
5236 7515
7512
7524 4
5020
7549
(M2)
7552
7553 (J101)
7525 5020
6008
7550 5236 5411
7533 (MS1) (J112)
5
7521 (J106)
7538 5020
7513
7518 7527 5169
(MS2) 5171
7522 (J106) 5511
5411 7526
7513 7548 7517
7523 7518
5020 5171 7532 6
7504 7529
5144
8
Fig. P03 Punch Main Body
529
Ver. 1.1 DEC 2006
DP-8060/8045/8035
530
Ver. 1.1 DEC 2006
DP-8060/8045/8035
A B C D E
7623
7603
7604
2
7611
7606
(M1) 5413
(J114) 7609
7624
5413
6409 7610 3
6431 7607
(PI3) 7608
(J104) 7607
7631
7632 (PI2)
5236 (J105) 7629
5236 4
7614 6431
6409 6409
6431
7618
7617
(J111)
5169
7628 5
6431
6409 7619 (J110)
5169 7615
7601
7618 5236
6
7616
5169
8
Fig. P04 Punch Slide Assembly
531
Ver. 1.1 DEC 2006
DP-8060/8045/8035
532
Ver. 1.1 DEC 2006
DP-8060/8045/8035
A B C D E
7700
(Q12)
7701
8
Fig. P05 Punch Driver PCB Assembly
533
Ver. 1.1 DEC 2006
DP-8060/8045/8035
534
Ver. 1.1 DEC 2006
DP-8060/8045/8035
A B C D E
J21
J23
J104 3
J3
J105 J1 J4
J2
J114 J5
J102 J7
J110 4
J101
J111
J112
5
J106
J106
8
Fig. P06 List Of Connectors
535
Ver. 1.1 DEC 2006
DP-8060/8045/8035
XB1–2 4 00 –6 09
Classification symbol ....................... Binding head machine screw
Material and surface treatment ........ Steel (black zinc plated) See table 1.
XB7–1 0 80 –4 09
Classification symbol ....................... Socket head cap screw
Length ( ) ........................................ 40 mm
Material and surface treatment ........ Steel (black zinc plated) See table 1.
Table 1
536
Ver. 1.1 DEC 2006
DP-8060/8045/8035
A-H
d
Flat Head Machine Screws Binding Head Self-Tapping Screws
d
d
B. Pan Head Machine Screws
Flat Head Self-Tapping Screws
d
d
E. Binding Head Machine Screws H. Pan Head Machine Screws with
Captive Spring Washer
d
537
Ver. 1.1 DEC 2006
DP-8060/8045/8035
class 1 class 3
d
L. Hex Socket Set Screws and
Socket Head Cap Screws How to Read Parts Numbers
Hex Socket Set Screws
XB7–2 1 00 –3 09
Normal diameter (d) ....... M3
d
538
Ver. 1.1 DEC 2006
DP-8060/8045/8035
t XD1–1 1 02 –6 25
Inner diameter (d) ......... 2.6 mm
* Material Brass
D (mm)
d (mm)
Class 1 Class 2 Class 3
1.5 – 2.6 3.2
1.8 2.7 3.1 3.7
2.1 3.2 3.6 4.2
2.3 3.6 4 4.6
2.6 4 4.4 5
3.1 4.6 5 5.6
3.6 5.4 5.8 6.4
4.1 5.7 6.6 8
4.6 6.4 7.4 9 Thickness Code t (mm)
5.2 7.2 8.2 10 0 0.05
5.7 7.8 9 11 1 0.1
6.2 8.5 9.8 12 2 0.2
6.7 9.2 10.5 13 3 0.3
7.2 10 11.4 14 4 0.4
7.7 10.6 12.2 15 5 0.5
8.2 11.4 13 16 6 0.6
8.7 12 13.8 17 7 0.7
9.2 12.8 14.6 18 8 0.8
9.7 13.5 15.4 19 9 1
Table 2 Table 3
539
Ver. 1.1 DEC 2006
DP-8060/8045/8035
XD1–2 1 00 –3 07
Inner diameter (d) ......... 3.0 mm
d
Plain washer Material and surface
treatment .......................Steel (nickel plated)
XD1–3 1 00 –5 07
Inner diameter (d) ......... 5.0 mm
d
Spring washer Material and surface
treatment .......................Steel (nickel plated)
540
Ver. 1.1 DEC 2006
DP-8060/8045/8035
V -W
V. E-Rings
How to Read Parts Numbers
XD2–1 1 00 –1 72
Inner diameter (d) ......... 1.7 mm
E ring
Material and surface treatment
W. Grip Rings
How to Read Parts Numbers
XD2–2 1 00 –5 02
Inner diameter (d) ......... 5.0 mm
d
Grip ring
Material and surface
treatment .......................Stainless
(without surface treatment)
541
Ver. 1.1 DEC 2006
DP-8060/8045/8035
X. C-Rings
How to Read Parts Numbers
Internal Type
Hole How to Read Parts Numbers
Table 5
542
Ver. 1.1 DEC 2006
DP-8060/8045/8035
Y-Z
V. Pins
XD3–1 2 00 –1 22
Nominal diameter (D) ....................... 2.0 mm
XD3–2 2 00 –0 82
Nominal diameter (d) ....................... 2.0 mm
VI. Spacers
Z. Spacer
How to Read Parts Numbers
XZ1–1 3 00 –3 0 2
Nominal diameter (d) ....................... 3.0 mm
543
Ver. 1.1 DEC 2006
DP-8060/8045/8035
544
Ver. 1.1 DEC 2006
DP-8060/8045/8035
A B C D E
15007
15008
15009
15044 3
15049
15045
15048
15047 15042 4
15047
15041
15037
8803 15040 5
15047
15039 15031
15032 15038
15033 8803 6
15038
15038
15038
8807
15038 15046
7
8805
8807 15036
15030 15038
8805
8
Fig. F-01 Finisher Mounting Kit
545
Ver. 1.1 DEC 2006
DP-8060/8045/8035
8.2. Covers
546
Ver. 1.1 DEC 2006
DP-8060/8045/8035
A B C D E
15102
15103
15101
2
15117
15110
15104
15105
15118 15240 3
15240
15119
15107
15108 15111 15112
15118
15106
15109
4
15119
15109
15118
5
15113
15240
6
15114
15118
7
15115
8
Fig. F-02 Covers
547
Ver. 1.1 DEC 2006
DP-8060/8045/8035
548
Ver. 1.1 DEC 2006
DP-8060/8045/8035
A B C D E
15201 (For North America)
15249 15212
15203
1
15210
15205
15206
15251 15247
15239
15249 15204
15231 15241 15249
15207 3
15215
15214 15224 15249
15242
15216 15218
15249 15248 15228 5
15225 15226
15217 15219 15230
15227 15249
15220 15226
15248 15220 15242
15206
15247
15223 15229 15232
15249 6
15228 15221
15242
15234
15247
15221 15233
15222
15235
15249
15240 7
15118
15238
15237 15236
8
Fig. F-03 Main Body
549
Ver. 1.1 DEC 2006
DP-8060/8045/8035
550
Ver. 1.1 DEC 2006
DP-8060/8045/8035
A B C D E
15303 2
15240 15338
15301 15336
15302
15248
15304
3
15334 15305
15240 15305
15307
15308 15309
15336 15333 15306
15307
4
15314 15311 15307
15310
15328
15307
15333 15312
15316
15317 15315 15307 5
15326 15307 15313
15320
15318 15335 15327
15319
15249
15324
15321
15329
15323 6
15119
15332 15337
15330
15322
15331 15325
15119
7
8
Fig. F-04 Transport Section 1
551
Ver. 1.1 DEC 2006
DP-8060/8045/8035
552
Ver. 1.1 DEC 2006
DP-8060/8045/8035
A B C D E
15434
15401
15434 15403
15237
15434
2
15402
15434
15221
3
15406 15315
15436
15117 15435 15408
15407
4
15410
15413 15436
15320 15412
15433 15436
15425 15415
15426 15320
15417 15326
15427 5
15418 15436
15419
15434
15428 15424 15436
15430 15429 15420 15322
15427
15436 15425 15422
15425 6
15436
15427
15436 15334
15338 15428
15427
15328
15423
15436 15436
15323 15424 15425
7
8
Fig. F-05 Transport Section 2
553
Ver. 1.1 DEC 2006
DP-8060/8045/8035
554
Ver. 1.1 DEC 2006
DP-8060/8045/8035
A B C D E
15434
15506
15503 15521
15525 15505
15510 15508
15504
3
15524
15515 15242
15516 15511 15507
15118 15525 15307 15508
15118
15519
15517 15502
15512 15501
4
15307
15513 15434
15527 15515
15514 15509
15503
15521 15504
15505
15526 15524
15508
15519
15434
15501
15502 15523
15526 15519 15509
15508
15520 15434 15237
15518 6
8
Fig. F-06 Elevate Section
555
Ver. 1.1 DEC 2006
DP-8060/8045/8035
556
Ver. 1.1 DEC 2006
DP-8060/8045/8035
A B C D E
15434
15237
3
15602
15434
15434
15603
15604
15614 15605 4
15606
15608
15434 15607
15609
15434 5
15616 15612
15615
15434
15610
15434
6
15611
15434
15615
15613
8
Fig. F-07 Finisher Driver PCB Assembly
557
Ver. 1.1 DEC 2006
DP-8060/8045/8035
memo
558
Ver. 1.1 DEC 2006
DP-8060/8045/8035
DC Controller
PCB Assembly 2
(Fig. F-13)
Dispose Assembly
(Fig. F-09)
3
Bundle Support
Cover Assembly
(Fig. F-08)
4
5
Mounting Hardware
Staple Assembly (Fig. F-02)
(Fig. F-12)
Fold Assembly
(Fig. F-11)
8
Fig. F-01 Assembly Location Diagram
559
Ver. 1.1 DEC 2006
DP-8060/8045/8035
Safety
Ref. No. Part Number Part Name Remarks
Mark
15700 NPN Mounting Hardware
15701 PF4117P738A Panel, Front Mounting Kit
15702 PF4117P737A Panel, Mounting Kit
15703 4A1-8547-000 Adjuster
15704 FC2-2120-000 Screw, M4 x 7
15705 4A1-8537-000 Plate, Mounting Kit Stopper
15706 4A1-8538-000 Rail, Slide
15707 PF4117P739A Panel, Rear Mounting Kit
15708 4A1-8543-000 Duct, Access Mounting Kit
15709 PF4117P772A Panel, Middle Mounting Kit
15710 PF4117K101A Plate, Latch
15711 030100FNBB Screw
15712 4G1-4388-000 Bracket, Mounting Kit Slide
15713 4A1-8539-000 Bracket, Mounting Kit
15714 4G1-4385-000 Frame, Mounting Kit Front
15715 4G1-4386-000 Frame, Mounting Kit Rear
15716 4A1-8540-000 Bracket, Mounting Kit Sub
15720 040300FNBP Screw, M4 x 30
5830 XB4-7401-007 Screw, M4 x 10 Truss Head Tapping
560
Ver. 1.1 DEC 2006
DP-8060/8045/8035
A B C D E
1
15711
15704
15704
2
15702 15706 15710
15712
15707
15704 3
15705
15704 15704
15704
15706 5830
15704 15720 4
5830 15704
15704
15713
15714 15708
5830
15715
5
5830
15703
15720
15709
15704
15708
15703
15701 15716
7
5830
8
Fig. F-02 Mounting Hardware
561
Ver. 1.1 DEC 2006
DP-8060/8045/8035
Safety
Ref. No. Part Number Part Name Remarks
Mark
15800 NPN External Covers, Panels, etc.
15801 4A1-7294-000 Knob, Jam Clearing
15802 PF4117P704A Panel, Rear
15803 PF4117P726A Panel, Frame Jam
15804 PF4117P706A Cover, Jam
15805 PF4117K304A Harness, Interface (CN1, CN2, CN20, JN3)
15806 FC2-5827-000 Clip
15807 PF4117P390A Panel, Dummy Puncher
15808 4A1-7380-000 Spring, Tension
15809 PF4117P763A Guide, Upper Dummy Punch
15810 PF4117P391A Guide, Dummy Punch
15811 PF4117P235A Panel, Side
15812 4A1-7291-000 Lever, Tray Up/Down Empty
15813 4A1-7293-000 Flag, Rear Paper Sensor
15814 4A1-7415-000 Spring, Tension
15815 4A1-7378-000 Latch, Upper Panel
15816 PF4117P700A Panel, Sub Upper
15817 PF4117P701A Panel, Upper
15818 4A1-7547-000 Spring, Torsion
15819 4A1-7548-000 Spring, Torsion
15820 4A1-7195-000 Holder, Roller
15821 4A1-7317-000 Roller, Paper Feed
15822 PF4117P702A Panel, Fixing
15823 PF4117P703A Panel, Front
15824 PF4099P955 Band, Panel
15825 4B1-0585-000 Support 2, Panel Band
15826 PF4117P727A Stack Tray, 1
15827 PF4117P728A Stack Tray, 2
15829 4A1-7424-000 Plate, Grounding
15830 PF4117P393A Panel 1, Dome
15831 PF4117P394A Panel 2, Dome
15832 4A1-7270-000 Flag, Base Tray
15833 PF4117P224A Tray, Base
15834 PF4117P381A Arm, Stopper
15835 4A1-7400-000 Spring, Tension
15836 4A1-7408-000 Spring, Tension
15837 4A1-7566-000 Clip, Shaft
15838 4A1-7567-000 Clip, Shaft
15839 4A1-8338-000 Guide, Dummy Puncher Paper
15840 4A1-8339-000 Label, Staple Removing
15841 4A1-7284-000 Gear, 15T 48T/Pulley
15842 PF4117P300A Cover, Frame Jam, Sub
15843 4B1-0584-000 Support 1, Panel Band
15844 PF4117P219 Stack, Tray Rib
15847 XB4-7300-607 Screw, M3 x 6 Truss Head Tapping
15848 4B1-0395-000 Bracket, Front Tray
15849 4B1-0394-000 Bracket, Rear Tray
15852 PF4048P076 Screw, M4
15853 PF2078P458 Screw, M4 x 6
5830 XB4-7401-007 Screw, M4 x 10 Truss Head Tapping
15704 FC2-2120-000 Screw, M4 x 7
562
Ver. 1.1 DEC 2006
DP-8060/8045/8035
A B C D E
15817 15805 1
15843
(CN1) (CN20)
To Puncher Unit (JN3)
15824 15815 Fig. P-02
(CN2)
15819 T
U 15704
To Fig. F-04
15827
2
15853 15807
15816
15820
5830 15839
15818
15815 5830 15821 15809
W 15808
To Fig. F-04
3
15844
15704
15802
15826 15849
15810
5830
X 4
To Fig. F-05
15848 15852
Z
5830 15704 To Fig. F-04 15811
Y 15841
15704 To Fig. F-04 15853
15824 15829 5
15825
15806 15847
15840
15813
15822
See Fig. F-08
15812
15853
15837 15843
15830 15824 6
15814 15838
15834 15806
15825
15831
15836
15823
15804 7
15801 15835
15832 15842
V 15803
15833 To Fig. F-04 5830
8
Fig. F-03 External Covers, Panels, etc.
563
Ver. 1.1 DEC 2006
DP-8060/8045/8035
Safety
Ref. No. Part Number Part Name Remarks
Mark
15900 NPN Internal Components 1
15901 4A1-7267-000 Gear, 24T/Pulley, 24T
15902 4A1-7577-000 Lever, Stack
15903 4A1-7259-000 Gear, 16T/Pulley, 18T
15905 FS1-9009-000 Screw, Stepped, M3
15906 4A1-7353-000 Holder, Belt, Rear
15907 4A1-7354-000 Holder, Belt, Front
15908 4A1-7371-000 Roller, Tension
15909 4A1-7428-000 Spring, Tension
15910 4A1-7414-000 Spring, Tension
15911 4A1-7417-000 Spring, Tension
15912 4A1-7419-000 Spring, Tension
15913 4A1-7509-000 Pulley, 18T/24T
15914 4A1-7517-000 Latch 1
15915 4A1-7518-000 Latch 2
(CN19,CN73)
15916 PF4117K341 Harness, Stack Sensor
For DP-8035/8045
15917 4A1-7523-000 Bushing
15918 4A1-7524-000 Pulley, 18T
15919 4A1-7528-000 Bushing
15920 4A1-7542-000 Flange
15922 4A1-7572-000 Bushing
15923 4A1-7691-000 Spring, Leaf
15924 4A1-7288-000 Pulley, 40T
15926 4S1-9077-000 Screw, M4 x 8
15927 4F1-1556-000 Plate 1, Paper Feed Tension
15929 4A1-7265-000 Roller, Rail
15930 4A1-7534-000 Cap, Motor
15931 4G1-5250-000 Guide, Stopper
15932 4A1-7539-000 Link 1
15933 4A1-7540-000 Link 2
15934 4A1-7549-000 Spring, Tension
(M2,CN57)
15935 PF4117K403 Motor, Stepping
For DP-8035/8045
15936 FC2-5034-000 Screw, M3 x 6 W/Washer
15937 4A1-7355-000 Pulley, 18T
15938 XF2-1817-960 Belt, Timing
15939 NS-BLT00230 Belt, Timing
15940 XF2-1619-860 Belt, Timing
(CN15, CN47-CN49, CN50)
15941 PF4117K327 Harness 1, Sensor
For DP-8035/8045
(CN10, CN56, CN57)
15942 PF4117K331 Harness, Feed Paddle Motor
For DP-8035/8045
(CN6, CN70, CN71)
15943 PF4117K339 Harness, DC Motor
For DP-8035/8045
15944 4A1-7321-000 Arm, Stopper
15947 4B1-0591-000 Clip, Shaft 5
15950 XD3-2300-142 Pin, Dowel
15951 4F1-1555-000 Assembly, Front Frame
15952 4A1-7253-000 Shaft, Latch
15953 PF4099K024 Bracket, Upper
15954 4A1-7217-000 Shaft, Stack
564
Ver. 1.1 DEC 2006
DP-8060/8045/8035
A B C D E
15910 15704
15704 15905
1
15959
15937
15835 15938
15920
15902 15964
5111 15926
(PI24) 15704
(CN73) 15906 15970 2
To Fig. F-03
15916 15929
Z 15806
(CN19)
15908
15927
15929 15912
15806
15961 15931 15923 15908
15934
To Fig. F-03 15929 15962 3
5609
15933 15901
Y 15929 15939
15933 15932 15806
15907 15704
15934 15944 15911 15913
15704 15947
15932 15917 A
15923
15911 15963 15936
15920 4
15947 15935
15938
15937 15965 15914
15960 15952 (CN57) (M2)
15966 To Fig. F-03
15704 W 15953 15704
15967
15910 15704 5
15926 15930
15704 15956
5829
15704 15940 15704
15924 15955
15922 15838
15838 To Fig. F-03 15957
15920 15954
15806 U
6
15915
15951 15704 15958 15704
15918 15969
15950 15909 15968
To Fig. F-03
15903
(CN56) (CN57)
15704
V 15920
(CN50) (CN71)
15919
15941 7
15950
(CN10) (CN49) A
15942 (CN48) 5830 15838 (CN6)
15922
(CN15) (CN70)
(CN47) 15943
See Fig. F-06
8
Fig. F-04 Internal Components 1
565
Ver. 1.1 DEC 2006
DP-8060/8045/8035
Internal Components 1
Safety
Ref. No. Part Number Part Name Remarks
Mark
15955 4F1-1554-000 Assembly, Rear Frame
15956 4B1-0390-000 Assembly, Motor Bracket
15957 4A1-7512-000 Frame Duct, Lower Rear Side
15958 4A1-7511-000 Frame Duct, Upper Rear Side
15959 PF4099P696A Bracket, Lever
15960 4A1-7174-000 Bracket, Stopper
15961 4F1-1883-000 Bracket, Front Tray
15962 4F1-1882-000 Bracket, Rear Tray
15963 4A1-7510-000 Duct, MR
15964 4F1-1558-000 Bracket, Front Tension
15965 4F1-1560-000 Bracket, Rear Tension
15966 4A1-7474-000 Bracket, Front
15967 4A1-7543-000 Duct, IN
15968 4A1-7489-000 Bracket, Reinforcement
15969 4A1-7491-000 Bracket, Frame
15970 PF4109P427 Screw, M4
(PI24 CN73)
5111 E314000729 IC, Photo-Interrupter TLP1241
For DP-8035/8045
5609 XF2-1605-040 Belt, Timing
5829 XD3-2200-142 Pin, Dowel
5830 XB4-7401-007 Screw, M4 x 10 Truss Head Tapping
15704 FC2-2120-000 Screw, M4 x 7
15806 FC2-5827-000 Clip
15835 4A1-7400-000 Spring, Tension
15838 4A1-7567-000 Clip, Shaft
566
Ver. 1.1 DEC 2006
DP-8060/8045/8035
A B C D E
15910 15704
15704 15905
1
15959
15937
15835 15938
15920
15902 15964
5111 15926
(PI24) 15704
(CN73) 15906 15970 2
To Fig. F-03
15916 15929
Z 15806
(CN19)
15908
15927
15929 15912
15806
15961 15931 15923 15908
15934
To Fig. F-03 15929 15962 3
5609
15933 15901
Y 15929 15939
15933 15932 15806
15907 15704
15934 15944 15911 15913
15704 15947
15932 15917 A
15923
15911 15963 15936
15920 4
15947 15935
15938
15937 15965 15914
15960 15952 (CN57) (M2)
15966 To Fig. F-03
15704 W 15953 15704
15967
15910 15704 5
15926 15930
15704 15956
5829
15704 15940 15704
15924 15955
15922 15838
15838 To Fig. F-03 15957
15920 15954
15806 U
6
15915
15951 15704 15958 15704
15918 15969
15950 15909 15968
To Fig. F-03
15903
(CN56) (CN57)
15704
V 15920
(CN50) (CN71)
15919
15941 7
15950
(CN10) (CN49) A
15942 (CN48) 5830 15838 (CN6)
15922
(CN15) (CN70)
(CN47) 15943
See Fig. F-06
8
Fig. F-04 Internal Components 1
567
Ver. 1.1 DEC 2006
DP-8060/8045/8035
Safety
Ref. No. Part Number Part Name Remarks
Mark
16000 NPN Internal Components 2
16001 4A1-7502-000 Cover, Stopper
16004 4B1-0586-000 Plate, Stapler Frame Stopper
16006 FS2-1672-000 Bushing
16008 4A1-8316-000 Cover, Blanking
16009 4A1-7515-000 Roller, Frame Tray
16010 4A1-7172-000 Guide, Lower Paper
16011 4A1-7349-000 Flag, Sensor
16012 4A1-7418-000 Spring, Tension
(CN43, CN44)
16013 PF4117K323 Harness, Sensor
For DP-8035/8045
16015 4F1-1557-000 Plate 2, Paper Feed Tension
16016 4A1-7336-000 Holder, Switch
16017 4H1-6449-000 Microswitch (MS1, MS2, CN68, CN69)
16018 NS-BLT00230 Belt, Timing
16019 4A1-7505-000 Flag, Top Sensor
16020 4A1-7506-000 Lever, Switch
16021 4A1-7507-000 Holder, Lever Support
16022 4A1-7508-000 Holder, Sensor/Microswitch
16023 4A1-7268-000 Gear, 24T
16024 PF4117P215A Guide 1, Paper Weight
16025 4A1-7495-000 Plate 1, Weight
16026 4A1-7496-000 Plate 2, Weight
16027 PF4117P751A Guide 2, Paper Weight
16028 4A1-7488-000 Panel, Frame Cover
16029 4A1-8314-000 Spring, Grounding Leaf
(CN4, CN23, CN24, CN25)
16030 PF4117K319 Harness, Front Door Sensor
For DP-8035/8045
(CN5, CN28, CN33, CN36)
16031 PF4117K321 Harness, Lever Tray Sensor
For DP-8035/8045
(CN16, CN37, CN42)
16032 PF4099K324 Harness 2, Sensor
For DP-8035/8045
(CN9, CN36, CN50, CN53)
16033 PF4099K329 Harness 3, Sensor
For DP-8035/8045
16034 4A1-7409-000 Spring, Tension
(CN3, CN62, CN64)
16035 PF4117K334 Harness, Jog Motor
For DP-8035/8045
(CN8, CN66, CN68, CN69)
16036 PF4117K336 Harness, Switch
For DP-8035/8045
(CN18, CN72)
16037 PF4117K328 Harness, Bind Clutch
For DP-8035/8045
16038 4A1-7382-000 Roller, Paper Feed
16039 4A1-8337-000 Plate, Switch Push
16041 XD3-2200-122 Pin, Dowel
16042 4A1-7425-000 Plate 1, Lock
16043 4A1-7426-000 Plate 2, Lock
16044 VT2-5019-030 Holder, Cord
16045 VT2-0002-018 Spacer
16046 VT2-5171-030 Holder, Cord
16047 4A1-7467-000 Bracket, Sensor
16048 4A1-7490-000 Bracket, Sensor
16049 PF4048P300 Screw, M4 x 5
568
Ver. 1.1 DEC 2006
DP-8060/8045/8035
A B C D E
1
(CN64)
See Fig. F-07
16035 15704
(CN53) 16001
(CN62)
16013
(CN50)
(CN3) (CN43)
(CN36)
5111 2
16049
(PI1) 16023
(CN44) 16041
(CN44) 15806 16018 15806
16049 15908
16006 16015
16033 16012 (CN72)
(CN9) 16037
16050
16011 (CN18)
16047
See Fig. F-13 3
15704
16010 16034 15926
16043
15704
15704 16044
16038
16009
16045 4
5111 (PI4)
To Fig. F-03
16009 B 16017
(CN23)
16004 X 16042 16016 (MS2)
(CN69)
16048
16039
16008
16049 16046
A (PI13) 15704
15704 (CN47) 15955 16036 5
16006 16025
15806 16024 5111
(CN66) (CN69)
16026
15704 15704 16027 B
5111 (PI22) 5111 (CN68) (CN8)
(CN25) (PI23) C
(CN24) 16028
15951 6
16019
16022
15704 (CN42)
16017 A 15704 16029
C (MS1) (CN23) (CN37)
15704 (CN36)
(CN68) (CN24) 16031
16021 16032 7
(CN33)
16020 (CN25) (CN28)
5830
(CN16)
(CN4)
(CN5)
16030
8
Fig. F-05 Internal Components 2
569
Ver. 1.1 DEC 2006
DP-8060/8045/8035
Internal Components 2
Safety
Ref. No. Part Number Part Name Remarks
Mark
16050 PF4060P027 Screw, M4 x 8
(PI1, PI4, PI13, PI22, PI23
CN44, CN23, CN47, CN25,
5111 E314000729 IC, Photo-Interrupter TLP1241
CN24)
For DP-8035/8045
5830 XB4-7401-007 Screw, M4 x 10 Truss Head Tapping
15704 FC2-2120-000 Screw, M4 x 7
15806 FC2-5827-000 Clip
15908 4A1-7371-000 Roller, Tension
15926 4S1-9077-000 Screw, M4 x 8
15951 4F1-1555-000 Assembly, Front Frame
15955 4F1-1554-000 Assembly, Rear Frame
570
Ver. 1.1 DEC 2006
DP-8060/8045/8035
A B C D E
1
(CN64)
See Fig. F-07
16035 15704
(CN53) 16001
(CN62)
16013
(CN50)
(CN3) (CN43)
(CN36)
5111 2
16049
(PI1) 16023
(CN44) 16041
(CN44) 15806 16018 15806
16049 15908
16006 16015
16033 16012 (CN72)
(CN9) 16037
16050
16011 (CN18)
16047
See Fig. F-13 3
15704
16010 16034 15926
16043
15704
15704 16044
16038
16009
16045 4
5111 (PI4)
To Fig. F-03
16009 B 16017
(CN23)
16004 X 16042 16016 (MS2)
(CN69)
16048
16039
16008
16049 16046
A (PI13) 15704
15704 (CN47) 15955 16036 5
16006 16025
15806 16024 5111
(CN66) (CN69)
16026
15704 15704 16027 B
5111 (PI22) 5111 (CN68) (CN8)
(CN25) (PI23) C
(CN24) 16028
15951 6
16019
16022
15704 (CN42)
16017 A 15704 16029
C (MS1) (CN23) (CN37)
15704 (CN36)
(CN68) (CN24) 16031
16021 16032 7
(CN33)
16020 (CN25) (CN28)
5830
(CN16)
(CN4)
(CN5)
16030
8
Fig. F-05 Internal Components 2
571
Ver. 1.1 DEC 2006
DP-8060/8045/8035
Safety
Ref. No. Part Number Part Name Remarks
Mark
16100 PF4117K211 Stack Motor Driver Assembly For DP-8035/8045
16101 4A1-7260-000 Gear, 16T/40T
16102 4A1-7261-000 Gear, 16T/45T
16103 4A1-7262-000 Gear, 16T/45T
16104 4A1-7263-000 Pulley, 56T
(CN70)
16105 PF4117K342 Harness, Shift Motor
For DP-8035/8045
(M6, CN70)
16106 PF4135K550 Motor, DC24V
For DP-8035/8045
16112 NS-BLT00072 Belt, Timing
16113 4A1-7264-000 Flag, Clock Sensor
16114 4A1-7469-000 Plate, Stack Motor
16115 4A1-7215-000 Shaft, Z1656
16116 4F1-1562-000 Assembly, Stack Motor Bracket
16117 4A1-7173-000 Bracket, Sensor
(PI16, PI17, CN49, CN48)
5111 E314000729 IC, Photo-Interrupter TLP1241
For DP-8035/8045
15704 FC2-2120-000 Screw, M4 x 7
15806 FC2-5827-000 Clip
15936 FC2-5034-000 Screw, M3 x 6 W/Washer
16006 FS2-1672-000 Bushing
16041 XD3-2200-122 Pin, Dowel
572
Ver. 1.1 DEC 2006
DP-8060/8045/8035
A B C D E
15806
16104 2
16041
16112
15806
16006
5111
16101 3
(PI16)
(CN49)
5111 (PI17)
(CN48)
16102
15806 4
15704
16103
16117
16041 15936
5
16113
15806
16116
15704 (CN70)
(M6) (CN70) 16105
(CN70)
16115 6
16106
16100
16114
16006
15806 7
8
Fig. F-06 Stack Motor Driver Assembly
573
Ver. 1.1 DEC 2006
DP-8060/8045/8035
Safety
Ref. No. Part Number Part Name Remarks
Mark
16200 PF4117K121 Drive Assembly For DP-8035/8045
16201 4A1-7301-000 Gear, 58T
16202 4A1-7302-000 Gear, 23T
16203 4A1-7303-000 Gear, 17T/65T
16204 4A1-7304-000 Gear, 15T/54T
16205 4A1-7305-000 Gear, 17T/29T
16206 4A1-7306-000 Gear, 20T
16207 4A1-7307-000 Pulley, 45T
16208 4A1-7338-000 Gear, 82T
16212 4A1-7573-000 Bushing
16214 FS2-1615-000 Bearing, Ball
16215 XF2-1807-000 Belt, Timing
16216 4A1-7300-000 Gear, 29T
16217 4S1-9081-000 Screw, M4 x 6
16218 4A1-7308-000 Flag, Clock Sensor
(M7, CN71)
16219 PF4117P556 Motor, DC24V
For DP-8035/8045
(PI14, CN52)
16220 E314000746 Photo-Interrupter
For DP-8035/8045
16221 4A1-7407-000 Spring, Compression
(CN7, CN11, CN72)
16222 PF4099K340 Harness, Stapler
For DP-8035/8045
16223 4S1-9049-000 Screw, M4 Stepped
16225 XD3-2300-182 Pin, Dowel
16226 4A1-7479-000 Plate, Drawer
16227 4A1-7516-000 Bracket, Drawer
16228 4A1-7229-000 Shaft, Gear 1
16229 4A1-7231-000 Shaft, Gear 2
16230 4F1-1563-000 Assembly, Gear Bracket
16231 4A1-7199-000 Plate, Motor Sensor
16232 4A1-7198-000 Bracket, Sub Gear
5829 XD3-2200-142 Pin, Dowel
15704 FC2-2120-000 Screw, M4 x 7
15837 4A1-7566-000 Clip, Shaft
15838 4A1-7567-000 Clip, Shaft
15922 4A1-7572-000 Bushing
16041 XD3-2200-122 Pin, Dowel
574
Ver. 1.1 DEC 2006
DP-8060/8045/8035
A B C D E
16231
(CN71) 16220 16218
16219
16227 (PI14)
(CN52) 2
15704
15704
16221 (M7)
16226 16217 16215
16230
15838
A
16223
16207 3
5829
16214
15704 16221 16228
(CN72) 16041
16216
A 15838
(CN7) 15837 4
16223 16212
16222
(CN11) 16208 16229
16225
16201
16202
15704 16202 5
15704
15922
15838
6
16232
16212 16204
16203
15837 15838 16205
16206
16200
8
Fig. F-07 Drive Assembly
575
Ver. 1.1 DEC 2006
DP-8060/8045/8035
Safety
Ref. No. Part Number Part Name Remarks
Mark
16300 PF4117K216 Bundle Support Cover Assembly For DP-8035/8045
16303 4A1-7416-000 Spring, Tension
16304 4A1-7420-000 Spring, Compression
16307 4A1-7240-000 Shaft, Support
16308 4A1-7289-000 Gear, 20T/28T
16309 PF4113P243 Flag, Paper Sensor
16310 4A1-7325-000 Gear, 5T
16311 4A1-7367-000 Bushing
16312 4A1-7421-000 Spring, Torsion
16313 4A1-7422-000 Spring, Torsion
16314 4A1-7423-000 Spring, Torsion
16315 4A1-7526-000 Holder, Sensor
16317 4A1-7326-000 Support, Paper
16318 4A1-7327-000 Holder, Paper Support
16319 4A1-7184-000 Bracket, Holder
16320 4F1-1566-000 Bracket, Tension
(PI9, CN35)
5111 E314000729 IC, Photo-Interrupter TLP1241
For DP-8035/8045
15704 FC2-2120-000 Screw, M4 x 7
15806 FC2-5827-000 Clip
15908 4A1-7371-000 Roller, Tension
(CN34, CN35)
16013 PF4117K323 Harness, Sensor
For DP-8035/8045
16050 PF4060P027 Screw, M4 x 8
576
Ver. 1.1 DEC 2006
DP-8060/8045/8035
A B C D E
16307
16311 2
16312
16314
16309
16310
3
16308 5111
(PI9)
16313 (CN35)
16318
16013
(CN34)
15704 4
16304
15806 16315
15908
16317 16320
16050 5
16319
16303
16300
8
Fig. F-08 Bundle Support Cover Assembly
577
Ver. 1.1 DEC 2006
DP-8060/8045/8035
Safety
Ref. No. Part Number Part Name Remarks
Mark
16400 PF4117K104 Dispose Assembly See Note 1
16401 4A1-7390-000 Spring, Tension
16404 XF2-1606-140 Belt, Timing
16405 4A1-7328-000 Lever, Belt Sensor
16406 4A1-7383-000 Belt, Timing
16407 4A1-7392-000 Spring, Torsion
16408 PF4117P303A Cover, Dispose See Note 2
16409 PF4117P268A Deflector, Weight See Note 2
(CN29-CN32)
16410 PF4117K322 Harness, Tray
For DP-8035/8045
16411 4K1-1067-000 Motor, Stepping M4,5 CN63,65
16413 4A1-7587-000 Guide, Front Tray
16415 4A1-7273-000 Gear, 30T
16416 4A1-7519-000 Cover, Sub Dispose
16417 4A1-7368-000 Pulley, 22T
16418 4A1-7381-000 Roller, Lower Bundle
16421 4A1-8319-000 Pulley, 22T
16422 4A1-8334-000 Flange
16423 4A1-7197-000 Support, Sensor Flag
16424 4A1-7329-000 Flag, Sensor
16425 4A1-7402-000 Spring, Tension
See Note 2 (CN13, CN59)
16426 PF4117K332 Harness, Eject Motor
For DP-8035/8045
16427 4A1-7275-000 Pulley, 22T
16428 4A1-7588-000 Guide, Tray Rear
16431 4A1-7209-000 Spring, Leaf
16432 PF4117P290A Guide, Front Paper Feed
16433 4A1-7514-000 Flag, Bundle Roller
(M1, M3, CN56, CN59)
16434 PF4117K401 Motor, Stepping
For DP-8035/8045
16435 PF4117P289A Guide, Rear Paper Feed
16436 4A1-7314-000 Rack, Adjustment, Front
16437 PF4117P276A Cover, Front Adjustment Rack
16438 PF4117P277A Cover, Front Adjustment Rack
16439 4A1-7391-000 Spring, Compression
16440 4A1-7319-000 Rack, Rear Adjustment
16441 PF4117P284A Cover, Rear Adjustment Rack
16442 4A1-7212-000 Holder, Microswitch
16443 4A1-7575-000 Cover, Microswitch
16444 4A1-7486-000 Bracket, Stepping Motor
16445 4A1-7236-000 Shaft, Lower
16446 4F1-1564-000 Assembly, Base
16447 4A1-7239-000 Shaft
16448 4A1-7196-000 Bracket
16449 4A1-7483-000 Bracket, Adjustment
16450 4A1-7266-000 Bracket, Upper Sensor
16451 4A1-7191-000 Bracket, Lower Sensor
16452 4A1-7193-000 Bracket, Sensor
16453 4A1-7487-000 Bracket, Lock
16454 4A1-7185-000 Bracket, Motor
16455 PF4117P261 Ms-SR-Weight Exit F
578
Ver. 1.1 DEC 2006
DP-8060/8045/8035
A B C D E
1
16457 15704
16456 15704 5111
16408
16455 15704
(CN50) 16450
(PI15)
16017 15704 16444
16460
16443 15936
15704 (MS3) (M1)
16459 16442
(CN66) (CN56) 2
16458
16416 (PI2)
15806 (CN51) 16434
16428
See Fig. F-10 5111
16427
7119 16404
16451 (CN54)
16050 16006
15704
16425
3
16006 16440
16441 (CN55) 16013
7119 16447 15704
16427
B 16413
15806 16423
16448
15704
16431 4
16438
16437 16432 16405 16424
16449
16439 16407 16435
16406 A
B 16445 15922
16436 16446 15838
16439
16422 5
16433 15838 16421
16415 16418
16431 16406 16041 16041
15838
A 16422
16417
15704 (CN31)
16418 6
5830
16041 (CN30)
5830 15838 (CN32)
16411 (M5) 15922
(CN65) 16401
15936 16411 16410
(PI7) (CN29)
(CN31)15936 16453 16404
(M4) 7
(CN63) 5111 15704 (M3) 16454
16452 (CN59) 16050
5111 (PI6) 16426
5111 16434
(CN30) (CN13)
(PI8)
16400
(CN32)
15704 15936 (CN59)
8
Fig. F-09 Dispose Assembly
Note 1:
This assembly includes the assembly shown in Figure F-10.
Note 2:
This assembly does not include the parts shown with key No. 16408, 16455-60, and 16426.
579
Ver. 1.1 DEC 2006
DP-8060/8045/8035
Dispose Assembly
Safety
Ref. No. Part Number Part Name Remarks
Mark
16456 PF4117P262 Ms-SR-Weight Exit M
16457 PF4117P263 Ms-SR-Weight Exit R
16458 PF4114P406 Sheet, F
16459 PF4114P403 Sheet, M
16460 PF4114P407 Sheet, R
(PI2, PI6-PI8, PI15, CN51,
5111 E314000729 IC, Photo-Interrupter TLP1241 CN30-CN32, CN50)
For DP-8035/8045
5830 XB4-7401-007 Screw, M4 x 10 Truss Head Tapping
7119 XD3-2200-102 Pin, Dowel
15704 FC2-2120-000 Screw, M4 x 7
15806 FC2-5827-000 Clip
15838 4A1-7567-000 Clip, Shaft
15922 4A1-7572-000 Bushing
15936 FC2-5034-000 Screw, M3 x 6 W/Washer
16006 FS2-1672-000 Bushing
(CN54, CN55)
16013 PF4117K323 Harness, Sensor
For DP-8035/8045
16017 4H1-6449-000 Microswitch (MS3, CN66)
16041 XD3-2200-122 Pin, Dowel
16050 PF4060P027 Screw, M4 x 8
580
Ver. 1.1 DEC 2006
DP-8060/8045/8035
A B C D E
1
16457 15704
16456 15704 5111
16408
16455 15704
(CN50) 16450
(PI15)
16017 15704 16444
16460
16443 15936
15704 (MS3) (M1)
16459 16442
(CN66) (CN56) 2
16458
16416 (PI2)
15806 (CN51) 16434
16428
See Fig. F-10 5111
16427
7119 16404
16451 (CN54)
16050 16006
15704
16425
3
16006 16440
16441 (CN55) 16013
7119 16447 15704
16427
B 16413
15806 16423
16448
15704
16431 4
16438 16424
16437 16432 16405
16449
16439 16407 16435
16406 A
B 16445 15922
16436 16446 15838
16439
16422 5
16433 15838 16421
16415 16418
16431 16406 16041 16041
15838
A 16422
16417
15704 (CN31)
16418 6
5830
16041 (CN30)
5830 15838 (CN32)
16411 (M5) 15922
(CN65) 16401
15936 16411 16410
(PI7) (CN29)
(CN31)15936 16453 16404
(M4) 7
(CN63) 5111 15704 (M3) 16454
16452 (CN59) 16050
5111 (PI6) 16426
5111 16434
(CN30) (CN13)
(PI8)
16400
(CN32)
15704 15936 (CN59)
8
Fig. F-09 Dispose Assembly
Note 1:
This assembly includes the assembly shown in Figure F-10.
Note 2:
This assembly does not include the parts shown with key No. 16408, 16455-60, and 16426.
581
Ver. 1.1 DEC 2006
DP-8060/8045/8035
Safety
Ref. No. Part Number Part Name Remarks
Mark
16500 PF4117K134 Paper Feeder Assembly See Note
16501 4A1-7278-000 Flange
16502 4A1-7281-000 Pulley, 20T
16503 4A1-7337-000 Guide, Paper Auxiliary
16505 4A1-7401-000 Spring, Tension
16506 4A1-7529-000 Claw, Front
16507 4A1-7538-000 Claw, Rear
16510 4A1-7271-000 Pulley, 40T
16511 4A1-7272-000 Pulley, 18T/29T
16512 4A1-7274-000 Gear, 32T 20T/Pulley
16513 4A1-7276-000 Flange
16514 4A1-7279-000 Gear, 20T
16515 4A1-7280-000 Gear, 20T 30T/Pulley
16516 4A1-7330-000 Flag, Sensor
16517 4A1-7331-000 Cam
16518 4A1-7332-000 Arm 1, Link
16519 4A1-7346-000 Support, Paddle Shaft
16520 4A1-7347-000 Arm 2, Link
16521 4A1-7348-000 Arm 3, Link
16522 4A1-7351-000 Pulley, 24T
16523 4A1-7366-000 Arm Link, 4
16524 4A1-8321-000 Spring, Compression
16525 4A1-7339-000 Flange
16526 4A1-7372-000 Guide 1, Rear Safety
16529 XF2-1606-140 Belt, Timing
16530 PF4099P847 Belt, Timing
16531 4A1-7194-000 Guide, Upper Paper Outlet
16532 4A1-7427-000 Eliminator, Static Charge
16533 PF4110P353 Guide 2, Rear Safety
16534 4A1-7406-000 Roller, Paper Outlet
16535 4A1-7494-000 Support, Paper Outlet Roller
16536 FB5-0735-000 Roller, Feed
16537 4A1-7531-000 Roller 1, Paper Outlet
16538 4A1-7532-000 Roller 2, Paper Outlet
16541 4A1-7513-000 Cam, Sensor Flag
16542 4A1-7585-000 Flange
16543 4A1-7333-000 Guide, Lower Paper
16544 4A1-7283-000 Gear, 14T
16545 4A1-7282-000 Gear, 14T
16546 4A1-7286-000 Holder 1, Front Roller
16547 4A1-7345-000 Holder 2, Front Roller
16548 4A1-7379-000 Roller, Upper Bundle
16549 PF4110P352 Guide 2, Front Safety
16550 4A1-7285-000 Holder 1, Rear Roller
16551 4A1-7344-000 Holder 2, Rear Roller
16552 4A1-7341-000 Guide 1, Front Safety
16553 4A1-7235-000 Shaft, Exit Roller
16554 4A1-7234-000 Shaft, Cam
16555 4A1-7238-000 Shaft, Upper Roller
16556 4A1-8320-000 Pad
16557 4A1-7237-000 Shaft, Paddle
582
Ver. 1.1 DEC 2006
DP-8060/8045/8035
A B C D E
1
15806
7119 16542
16500
16522
7119
16521
16538 15806
16006 15806
16537
16553 15704 16525 2
16538 16560 16530
16510
15704 7119
5111 16517
15806
(PI3) 16541
(CN55) 7119 15806
(PI5) 16006 16516
(CN36) 7119
16513 3
16511
16520
16523
16531 5111 16515
16514
16532
16505
16006 15704 16006 15808
16521 16566 4
15806 16565 A 16558
16562
16564
15806
16513
16559 16512
15704 16543
16561 16535
16554
16534 16536
5830 16526
A 5
16536 1650116550
16006 16529
16502 16545 16556
16518 16556 7119 16551
15806 16563 16006 16544 16503 16556
7119 16519
16524 16547
16517 16545
15806 16548
16546 6
16520 16555 16533
15808 16552
16505 16544
7119
15806 16568 16548
16567 16569
16569 16556
7
16570
16567 16567
16569 16557 16549
16556
16507
16506
8
Fig. F-10 Paper Feeder Assembly
Note:
This assembly is included in the assembly shown in Figure F-09.
583
Ver. 1.1 DEC 2006
DP-8060/8045/8035
Safety
Ref. No. Part Number Part Name Remarks
Mark
16558 4F1-1565-000 Frame, Rear SR
16559 4A1-7202-000 Frame, Front SR
16560 4A1-7192-000 Bracket, Sensor
16561 PF4113P418 Sheet, Front ML
16562 PF4113P419 Sheet, Rear ML
16563 PF4113P413 Sheet, Front ML-SR
16564 PF4113P414 Sheet, Rear ML-SR
16565 PF4117P271 Sheet, SR-MLR-GID L
16566 PF4117P270 Sheet, SR-MLR-GID
16567 4B1-0149-000 Holder, SIRC-SR Paddle
16568 4B1-0111-000 Holder, KM-SR Paddle
16569 4B1-0140-000 Paddle 1, KM-SR
16570 4B1-0148-000 Paddle, THIN
(PI3, PI5, CN55, CN36)
5111 E314000729 IC, Photo-Interrupter TLP1241
For DP-8035/8045
5830 XB4-7401-007 Screw, M4 x 10 Truss Head Tapping
7119 XD3-2200-102 Pin, Dowel
15704 FC2-2120-000 Screw, M4 x 7
15806 FC2-5827-000 Clip
15808 4A1-7380-000 Spring, Tension
16006 FS2-1672-000 Bushing
584
Ver. 1.1 DEC 2006
DP-8060/8045/8035
A B C D E
1
15806
7119 16542
16500
16522
7119
16521
16538 15806
16006 15806
16537
16553 15704 16525 2
16538 16560 16530
16510
15704 7119
5111 16517
15806
(PI3) 16541
(CN55) 7119 15806
(PI5) 16006 16516
(CN36) 7119
16513 3
16511
16520
16523
16531 5111 16515
16514
16532
16505
16006 15704 16006 15808
16521 16566 4
15806 16565 A 16558
16562
16564
15806
16513
16559 16512
15704 16543
16561 16535
16554
16534 16536
5830 16526
A 5
16536 1650116550
16006 16529
16502 16545 16556
16518 16556 7119 16551
15806 16563 16006 16544 16503 16556
7119 16519
16524 16547
16517 16545
15806 16548
16546 6
16520 16555 16533
15808 16552
16505 16544
7119
15806 16568 16548
16567 16569
16569 16556
7
16570
16567 16567
16569 16557 16549
16556
16507
16506
8
Fig. F-10 Paper Feeder Assembly
Note:
This assembly is included in the assembly shown in Figure F-09.
585
Ver. 1.1 DEC 2006
DP-8060/8045/8035
Safety
Ref. No. Part Number Part Name Remarks
Mark
16606 4A1-7299-000 Cam, Front Saddle
16608 PF4117K161 Fold Assembly
16611 4A1-7357-000 Pulley, 27T
16617 4A1-7363-000 Cam, Rear Saddle
16618 4A1-7364-000 Gear, 24T
16620 4A1-7376-000 Gear, 16T/42T
16621 4A1-7377-000 Gear, 21T
16622 4A1-7385-000 Roller, Fold
16625 4A1-7388-000 Spring, Tension
16630 4A1-7533-000 Hook, Spring
16632 4A1-7552-000 Bushing
16633 PF4113P439 Gear, SP-S
16634 PW060050 Polyslider
16636 ER050SU-D E-Ring
16638 4A1-8330-000 Gear, 18T
16640 4A1-8332-000 Guide, Lower Paper Delivery
(CL1, CN72)
16642 PF4099K355 Clutch, Electromagnetic
For DP-8035/8045
16650 4A1-7476-000 Spring, Leaf
16672 4A1-7525-000 Roller
16681 4A1-7256-000 Roller
16682 4A1-7504-000 Harness Duct
16683 4A1-7477-000 Bracket, Top
16684 4A1-1568-000 Frame, Front
16685 4A1-1567-000 Frame, Rear
16686 4A1-7485-000 Bracket, Front Tension
16687 4A1-7227-000 Cam
(PI11, PI12, CN40, CN41)
5111 E314000729 IC, Photo-Interrupter TLP1241
For DP-8035/8045
5509 XD3-2300-162 Pin, Dowel
7119 XD3-2200-102 Pin, Dowel
15704 FC2-2120-000 Screw, M4 x 7
15806 FC2-5827-000 Clip
15837 4A1-7566-000 Clip, Shaft
16006 FS2-1672-000 Bushing
16212 4A1-7573-000 Bushing
586
Ver. 1.1 DEC 2006
DP-8060/8045/8035
A B C D E
1
15806
16672 16632
16625 16636
16634
16638
16681
16634
15806 16633 2
15837
16212
16672 15704 16686
16685
16682 15704
15704 16006
16642
5111 7119
15806 (PI12) 16611 3
(CN41)
16630 (CL1)
(CN72)
16625
16006
16632 16684 16621
15806 16006
(PI11) 4
(CN40) 15806
5111 16620
16650 16683
15704
16622 5
5509
15704
16617
15837
16212
5509
16618 16687
15837 6
15837
16606
16006 5509
15806
15704
16640 7
16608
15704
8
Fig. F-11 Fold Assembly (1/3)
587
Ver. 1.1 DEC 2006
DP-8060/8045/8035
Fold Assembly
Safety
Ref. No. Part Number Part Name Remarks
Mark
16601 4A1-7177-000 Guide, Front Swing
16602 4A1-7178-000 Guide, Rear Swing
16604 4A1-7295-000 Cam, Front
16605 4A1-7296-000 Cam, Rear
16607 4A1-7335-000 Pulley, 36T
16610 4A1-7350-000 Pin, Saddle Slider
16615 4A1-7361-000 Holder, Roller
16624 4A1-7387-000 Spring, Tension
16630 4A1-7533-000 Hook, Spring
16631 4A1-7551-000 Washer
16637 4A1-8329-000 Roller, Link
16639 4A1-8331-000 Gear, 17T
16643 4S1-9048-000 Screw, M3 Stepped
16655 4A1-8327-000 Spring, Leaf
16656 4A1-8326-000 Spring, Leaf
16657 4A1-7480-000 Guide, Delivery Paper
16658 4A1-8324-000 Plate, Reinforcement
16659 4A1-7322-000 Roller, Fold
16660 4A1-7481-000 Holder, Delivery Roller
16668 4A1-7297-000 Roller, Link
16671 4A1-7228-000 Shaft, Link
16673 4A1-7546-000 Spring, Tension
16674 4A1-7298-000 Roller, Saddle
16675 4F1-1569-000 Plate, Front Opener
16676 4F1-1570-000 Plate, Rear Opener
16677 4A1-7181-000 Link, Cover
16678 HW050FZS Washer
16679 ER040SU-D E-Ring
16680 XB1-2401-000 Screw, M4 x 10 Truss Head Mach.
16684 4A1-1568-000 Frame, Front
16685 4A1-1567-000 Frame, Rear
16688 4A1-7242-000 Cam, Front
16689 4A1-7180-000 Bracket, Saddle
16690 4A1-7179-000 Plate, Saddle
16691 4A1-7188-000 Plate, Sub
16692 4A1-7203-000 Bracket, Base
166001 4A1-8325-000 Base, Plate Spring
166002 4A1-8328-000 Pad
5829 XD3-2200-142 Pin, Dowel
15704 FC2-2120-000 Screw, M4 x 7
15806 FC2-5827-000 Clip
15837 4A1-7566-000 Clip, Shaft
15838 4A1-7567-000 Clip, Shaft
16212 4A1-7573-000 Bushing
16525 4A1-7339-000 Flange
588
Ver. 1.1 DEC 2006
DP-8060/8045/8035
A B C D E
16212
16677
16212
5829
16605
16615 166002
16631 2
15837
16658
16688 C D
166001 15704
15837 16676
16679
16631
16615 16678 16656 3
16604 16668 16655
5829 16671 16680
16212 16637
16677 16637 C D
16212 16671
16668 16674 See
166001 16673
16678 Fig. F5-18
16679 16689 16607
166002 16639
15837 4
16658 16212
15806
16656 16630 15704 16525
16655 15704 15838
16680 16675
16690
16691 16643
16660 16610 5
16674 15704 16602
16659
15704 16624
16212 16684 16685
15837
16657 15704
6
15704
15838
16610
16643
16692
7
16601
15704
16624
8
Fig. F-11 Fold Assembly (2/3)
589
Ver. 1.1 DEC 2006
DP-8060/8045/8035
Fold Assembly
Safety
Ref. No. Part Number Part Name Remarks
Mark
16603 4A1-7290-000 Gear, 8T
16609 4A1-7340-000 Gear, 16T
16612 4A1-7358-000 Gear, 16T/41T
16613 4A1-7359-000 Gear, 15T/38T
16614 4A1-7360-000 Gear, 24T
16616 4A1-7362-000 Gear, 24T
16619 4A1-7365-000 Gear, 16T
16623 4A1-7386-000 Spring, Compression
16626 4A1-7389-000 Spring, Tension
16627 4A1-7403-000 Spring, Tension
16628 4A1-7404-000 Roller
16629 4A1-7530-000 Pulley, 27T
16635 FC2-1175-000 Screw
(CN38-CN41)
16641 PF4099K325 Harness, Connecting
For DP-8035/8045
16645 4H1-6450-000 LED PCB Unit (PI10, CN39)
16649 XF2-1607-240 Belt, Timing
16651 4A1-7536-000 Clip, Shaft
16652 4A1-7544-000 Roller, Fold
16653 4A1-7545-000 Roller, Sub Fold
16661 4A1-7187-000 Guide 1, Fold Roller
16662 4A1-7309-000 Holder 1, Front Guide
16663 4A1-7310-000 Holder 1, Rear Guide
16664 4A1-7186-000 Guide 2, Fold Roller
16665 4A1-7311-000 Holder 2, Front Guide
16666 4A1-7312-000 Holder 2, Rear Guide
16667 4A1-7207-000 Guide, Upper Paper
16669 4A1-7204-000 Guide, Lower Paper
16670 4A1-8322-000 Spring, Grounding Leaf
16684 4A1-1568-000 Frame, Front
16685 4A1-1567-000 Frame, Rear
16693 4A1-7410-000 Mirror Seal
16694 4G1-4061-000 Guide, Lower Paper Assembly
16695 4A1-7175-000 Roller, Front Fold
16696 4A1-7176-000 Roller, Rear Fold
16697 4A1-7470-000 Flame, Front Sub
16698 4A1-7492-000 Bracket
16699 4A1-7254-000 Fold 1
16600 4A1-7255-000 Fold 2
7119 XD3-2200-102 Pin, Dowel
15704 FC2-2120-000 Screw, M4 x 7
15806 FC2-5827-000 Clip
15838 4A1-7567-000 Clip, Shaft
15950 XD3-2300-142 Pin, Dowel
16006 FS2-1672-000 Bushing
16214 FS2-1615-000 Bearing, Ball
16225 XD3-2300-182 Pin, Dowel
590
Ver. 1.1 DEC 2006
DP-8060/8045/8035
A B C D E
(CN38) 16629 1
16635 7119 15806
(CN40) 16006
16645 15838
(CN41)
(PI10) (CN39) 16649
(CN39) 16626
16667 16641 16696
16693
16609 2
16694 1595016603
15704 16214
16685 15838
15704
15704
15950
16623
16695 16670 15838 3
16609
16214 16669 15950
15838 16006 15704 16214 15704
15806 16698
15838 16628
16684
15704 4
1580616619
16616 16651
15838 16661
16612
16214
16697 15950 16651 16663 5
16614 16653
15838
E
16626 16613
16666
16699 16627
16651 16653
6
16652 E
16225
15704 16600
16653
16651
16662
16664
16652
7
16225
16653
16665 16627
8
Fig. F-11 Fold Assembly (3/3)
591
Ver. 1.1 DEC 2006
DP-8060/8045/8035
Safety
Ref. No. Part Number Part Name Remarks
Mark
16701 4A1-8206-000 Roller, Tension
16702 4A1-8207-000 Spring, Tension
16703 4A1-8214-000 Cover, Motor
16705 4A1-8217-000 Support 1, Cam Stopper
16710 4A1-7592-000 Spring, Torsion
16711 4A1-8225-000 Pulley, 38T
16713 4A1-8228-000 Knob, Staple Movable
16717 4A1-8233-000 Knob, Jam Clearing
16718 FC3-0661-000 Clip
16721 4S1-9076-000 Screw, M3 x 8
16722 4A1-8238-000 Panel, Front
16723 4A1-8239-000 Cover, Handle
16726 4A1-8240-000 Guide, Paper
16727 4B1-0743-000 Spring, Compression
16728 4A1-7581-000 Guide, Sub Upper
16729 4A1-7584-000 Pin, Marker
16731 4A1-7583-000 Gear, 42T
16732 4F1-1679-000 Plate, Tension
16733 FC3-0779-000 Screw, M3 x 6 Tapping
16735 4A1-8210-000 Pin, Slide
16736 4A1-8198-000 Roller
(CN72, JN1)
16741 PF4099K315 Harness 2, Staple
For DP-8035/8045
(M8, CN72)
16742 PF4117K405 Motor, Stepping
For DP-8035/8045
16743 4B1-0754-000 Flange
16744 4B1-0744-000 Gear
16745 4S1-0280-000 Spring, Tension
16746 4F1-2053-000 Support, Staple Tension
16747 4B1-0746-000 Roller, Tension
16748 4A1-8232-000 Gear, 18T/66T
16749 XF2-1804-070 Belt, Timing
16750 4B1-0742-000 Guide
16751 4A1-7590-000 Pad, Staple Guide
16752 RA2-2452-000 Bushing
16753 4B1-0740-000 Gear, 29T 16T/Pulley
16756 XB1-2300-605 Screw, M3 x 6 Truss Head Mach.
16761 4A1-8881-000 Harness
16762 4A1-8211-000 FPC Guide
16763 PF4117K226A Stapler Unit
16764 NS-BLT00234 Belt
5413 XD2-1100-502 E-Ring
5511 XD2-1100-642 E-Ring
5830 XB4-7401-007 Screw, M4 x 10 Truss Head Tapping
15853 PF2078P458 Screw, M4 x 6
15926 4S1-9077-000 Screw, M4 x 8
15936 FC2-5034-000 Screw, M3 x 6 W/Washer
15950 XD3-2300-142 Pin, Dowel
592
Ver. 1.1 DEC 2006
DP-8060/8045/8035
A B C D E
1
16763
16733 (M8)
(CN72)
16703
16761 15936
2
16742
(CN72)
16741
16705 16721
16756 16732
16733 (JN1) 3
16733
5413
16701
5413 16762 16702
5511
5413
16711
16729 15950 4
16731
16764
5413 16761
16750
16736
16727
16743 16735
16726 5
16744
5511
1673516736
16745
16748
16717 15926
16746 16751
5511
16747 6
5413 16728
16753
5511 16733
16749 16718
16710
5830 16752
16723 7
16722
16713
15853
8
Fig. F-12 Staple Assembly (1/2)
Note 1:
This assembly includes the assembly shown in Figure F-12 (1/2 - 2/2).
593
Ver. 1.1 DEC 2006
DP-8060/8045/8035
Staple Assembly
Safety
Ref. No. Part Number Part Name Remarks
Mark
16704 4A1-8215-000 Frame, Coupling
16706 4A1-8218-000 Coupling
16707 4A1-8219-000 Spring, Compression
16708 4A1-7591-000 Holder, Staple Guide Roller
16709 4A1-7589-000 Roller, Staple Guide
16712 4A1-8226-000 Gear, 38T 36T/Pulley
16714 4A1-8229-000 Gear, 32T 42T/Pulley
16715 4A1-8230-000 Pulley, 24T
16716 XF2-1809-000 Belt, Timing
16720 FC2-5035-000 Screw, M3 x 6 W/Washer
16724 4A1-8265-000 Cover, Right Side
16725 4A1-8264-000 Cover, Left Side
16730 4A1-8263-000 Cover, Gear
16734 4A1-8341-000 Staple Cartridge Unit
16737 PF4117K312 Stapler Base PCB Assembly For DP-8035/8045
16738 PF4117K313 Stapler In PCB Assembly For DP-8035/8045
(CNJN1, JN2)
16739 PF4117P530 Harness, Stapler
For DP-8035/8045
(CNJN2)
16740 PF4117K314 Harness 1, Staple
For DP-8035/8045
16760 XD3-2300-122 Pin, Dowel
16764 NS-BLT00234 Belt
16765 XF2-1309-711 Belt
5413 XD2-1100-502 E-Ring
5511 XD2-1100-642 E-Ring
5829 XD3-2200-142 Pin, Dowel
594
Ver. 1.1 DEC 2006
DP-8060/8045/8035
A B C D E
16724
5413
2
16730
5511
16712
16725 5829
16764
5511
5413 16706
16760
3
16707
16708
16709
16709
16704
16737
A (JN2)
4
(JN1) 16739
16765
16760 5
16734
16714
5511
16716
16760
16715 16738
5511
6
A 16720
(JN2)
7
16740
8
Fig. F-12 Staple Assembly (2/2)
595
Ver. 1.1 DEC 2006
DP-8060/8045/8035
Safety
Ref. No. Part Number Part Name Remarks
Mark
16800 PF4117K303A DC Controller PCB Assembly
16801 PF4117K302A IC, EP-ROM M27C1001-70XF (IC6)
16802 E323000483 IC, EP-ROM S-93C46ADP (IC12)
596
Ver. 1.1 DEC 2006
DP-8060/8045/8035
A B C D E
16800
(IC6)
5
(IC12) 16801
16802
8
Fig. F-13 DC Controller PCB Assembly
597
Ver. 1.1 DEC 2006
DP-8060/8045/8035
Safety
Ref. No. Part Number Part Name Remarks
Mark
PCB DC Controller
CN3
PF4117K334 Harness, Jog Motor For DP-8035/8045
PCB DC Controller
CN4
PF4117K319 Harness, Front Door Sensor For DP-8035/8045
PCB DC Controller
CN5
PF4117K321 Harness, Lever Tray Sensor For DP-8035/8045
PCB DC Controller
CN6
PF4117K339 Harness, DC Motor For DP-8035/8045
PCB DC Controller
CN8
PF4117K336 Harness, Switch For DP-8035/8045
PCB DC Controller
CN9
PF4099K329 Harness 3, Sensor For DP-8035/8045
SYS Puncher Unit
CN12
PCB DC Controller
PCB DC Controller
CN13
PF4117K332 Harness, Eject Motor For DP-8035/8045
SYS Puncher Unit
CN14
PCB DC Controller
PCB DC Controller
CN15
PF4117K327 Harness 1, Sensor For DP-8035/8045
NPN Front Jog Home Position Sensor (PI4)
CN23
PF4117K319 Harness, Front Door Sensor For DP-8035/8045
NPN Top Cover Sensor (PI23)
CN24
PF4117K319 Harness, Front Door Sensor For DP-8035/8045
NPN Front Door Sensor (PI22)
CN25
PF4117K319 Harness, Front Door Sensor For DP-8035/8045
CN28 PF4117K321 Harness, Lever Tray Sensor For DP-8035/8045
CN29 PF4117K322 Harness, Tray For DP-8035/8045
NPN Adjustment Tray Sensor (PI6)
CN30
PF4117K322 Harness, Tray For DP-8035/8045
NPN Eject Belt Home Position Sensor (PI7)
CN31
PF4117K322 Harness, Tray For DP-8035/8045
NPN Tray Paper Empty Sensor
CN32
PF4117K322 Harness, Tray For DP-8035/8045
CN33 PF4117K321 Harness, Lever Tray Sensor For DP-8035/8045
CN34 PF4117K323 Harness, Sensor For DP-8035/8045
NPN Level Sensor (PI9)
CN35
PF4117K323 Harness, Sensor For DP-8035/8045
NPN Rear Jog Home Position Sensor (PI5)
PF4117K321 Harness, Lever Tray Sensor For DP-8035/8045
CN36
NPN Rear Jog Home Position Sensor (PI5)
PF4099K329 Harness 3, Sensor For DP-8035/8045
NPN Bind Position Sensor (PI10)
CN39
PF4099K325 Harness, Connecting For DP-8035/8045
NPN Bind Empty Sensor (PI13)
CN47
PF4117K327 Harness 1, Sensor For DP-8035/8045
NPN Shift Clock Sensor (PI17)
CN48
PF4117K327 Harness 1, Sensor For DP-8035/8045
NPN Shift Down Limit Sensor (PI16)
CN49
PF4117K327 Harness 1, Sensor For DP-8035/8045
598
Ver. 1.1 DEC 2006
DP-8060/8045/8035
A B C D E
CN66
CN71
CN49
CN48 CN52 2
CN68
CN23
CN24 CN4 3
CN25 CN6
CN69
CN70 CN15
CN70
CN47 CN8
CN53
CN54
CN36 CN55
CN64 CN39 CN50
CN65
5
CN36
CN31 CN13
CN62 CN35 CN3
CN63 CN34
CN33 6
CN32 CN5
CN29
CN28 CN30
CN9 CN14
CN12
8
Fig. F-14 List of Connectors (1/2)
599
Ver. 1.1 DEC 2006
DP-8060/8045/8035
List of Connectors
Safety
Ref. No. Part Number Part Name Remarks
Mark
NPN Shift Up Limit Sensor (PI15)
CN50
PF4099K329 Harness 3, Sensor For DP-8035/8045
NPN Bind Clock Sensor (PI14)
CN52
PF4099K329 Harness 1, Sensor For DP-8035/8045
CN53 PF4099K329 Harness 3, Sensor For DP-8035/8045
CN54 PF4117K323 Harness, Sensor For DP-8035/8045
NPN Bundle Roller Home Position Sensor (PI3)
CN55
PF4117K323 Harness, Sensor For DP-8035/8045
CN62 PF4117K334 Harness, Jog Motor For DP-8035/8045
CN63 NPN Front Jog Motor (M4)
CN64 PF4117K334 Harness, Jog Motor For DP-8035/8045
CN65 NPN Rear Jog Motor (M5)
NPN Stapler Safety Switch (MS3)
CN66
PF4117K336 Harness, Switch For DP-8035/8045
NPN Front Door Switch (MS1)
CN68
PF4117K336 Harness, Switch For DP-8035/8045
NPN Joint Switch (MS2)
CN69
PF4117K336 Harness, Switch For DP-8035/8045
PF4117K339 Harness, DC Motor For DP-8035/8045
CN70 NPN Shift Motor (M6)
PF4117K342 Harness, Shift Motor For DP-8035/8045
NPN Bind Motor (M7)
CN71
PF4117K339 Harness, DC Motor For DP-8035/8045
600
Ver. 1.1 DEC 2006
DP-8060/8045/8035
A B C D E
CN66
CN71
CN49
CN48 CN52 2
CN68
CN23
CN24 CN4 3
CN25 CN6
CN69
CN70 CN15
CN70
CN47 CN8
CN53
CN54
CN36 CN55
CN64 CN39 CN50
CN65
5
CN36
CN31 CN13
CN62 CN35 CN3
CN63 CN34
CN33 6
CN32 CN5
CN29
CN28 CN30
CN9 CN14
CN12
8
Fig. F-14 List of Connectors (1/2)
601
Ver. 1.1 DEC 2006
DP-8060/8045/8035
List of Connectors
Safety
Ref. No. Part Number Part Name Remarks
Mark
PCB DC Controller
CN1
PF4117K304A Harness, Interface
PCB DC Controller
CN2
PF4117K304A Harness, Interface
PCB DC Controller
CN7
PF4117K340 Harness, Stapler For DP-8035/8045
PCB DC Controller
CN10
PF4110K331A Harness, Feed Paddle Motor
PCB DC Controller
CN11
PF4117K340 Harness, Stapler For DP-8035/8045
PCB DC Controller
CN16
PF4117K324 Harness 2, Sensor
PCB DC Controller
CN18
PF4117K328 Harness, Bind Clutch For DP-8035/8045
PCB DC Controller
CN19
PF4117K341 Harness, Stack Sensor For DP-8035/8045
SYS To Copier
CN20
PF4117K304A Harness, Interface
CN37 PF4117K324 Harness 2, Sensor For DP-8035/8045
CN38 PF4099K325 Harness, Connecting For DP-8035/8045
NPN Bind Position Sensor (PI10)
CN39
PF4099K325 Harness, Connecting For DP-8035/8045
NPN Bind Home Position Sensor (PI11)
CN40
PF4099K325 Harness, Connecting For DP-8035/8045
NPN Bind Roller Home Position Sensor (PI12)
CN41
PF4099K325 Harness, Connecting For DP-8035/8045
CN42 PF4117K324 Harness 2, Sensor
CN43 PF4117K323 Harness, Sensor For DP-8035/8045
NPN Entrance Sensor (PI1)
CN44
PF4117K323 Harness, Sensor For DP-8035/8045
NPN Paper Feed Motor (M1)
CN56
PF4110K331A Harness, Feed Paddle Motor
NPN Paddle Motor (M2)
CN57
PF4110K331A Harness, Feed Paddle Motor
NPN Bind Clutch (CL1)
PF4117K328 Harness, Bind Clutch For DP-8035/8045
CN72 NPN Slide Motor (M8)
PF4117K340 Harness, Stapler For DP-8035/8045
PF4099K315 Harness 2, Staple For DP-8035/8045
NPN Stack Sensor (PI24)
CN73
PF4117K341 Harness, Stack Sensor For DP-8035/8045
PCB Stapler Base
PF4117P530 Harness, Stapler For DP-8035/8045
JN1
PCB Stapler IN
PF4099K315 Harness 2, Staple For DP-8035/8045
PCB Stapler Base
PF4117P530 Harness, Stapler For DP-8035/8045
JN2
PCB Stapler IN
PF4117K314 Harness 1, Staple For DP-8035/8045
SYS To Copier
JN3
PF4117K304A Harness, Interface
602
Ver. 1.1 DEC 2006
DP-8060/8045/8035
A B C D E
CN57
CN72
2
CN56
CN73
CN72
CN7
CN19 3
CN11
JN2 JN1 CN10
JN2
JN1
CN44
CN72
CN43 5
CN41 CN42
CN37
CN40 CN38
CN39
6
CN20
CN18 JN3
CN1
CN2
CN16
7
8
Fig. F-14 List of Connectors (2/2)
603
Ver. 1.1 DEC 2006
DP-8060/8045/8035
Safety
Ref. No. Part Number Part Name Remarks
Mark
CL1 PF4099K355 Clutch, Electromagnetic
604
Ver. 1.1 DEC 2006
DP-8060/8045/8035
A B C D E
MS3
PI14 2
PI16
PI24
PI4
PI23 PI17
MS1 3
PI22
PI13 MS2
PI18 4
PI15
PI5 PI3
PI1 5
PI2
PI7 PI12
CL1
PI8 PI9
PI6
PI11
PI10 6
8
Fig. F-15 List of Electric Parts (1/2)
605
Ver. 1.1 DEC 2006
DP-8060/8045/8035
Safety
Ref. No. Part Number Part Name Remarks
Mark
M1 PF4117K403 Motor, Stepping For DP-8035/8045
606
Ver. 1.1 DEC 2006
DP-8060/8045/8035
A B C D E
M1
M2
M8
M3 M7 5
M5
M4
6
[1]
M6
8
Fig. F-15 List of Electric Parts (2/2)
607
Ver. 1.1 DEC 2006
DP-8060/8045/8035
memo
608
Ver. 1.1 DEC 2006
DP-8060/8045/8035
Puncher Total
Assembly (Fig. P-03)
Puncher
Assembly 6
(Fig. P-02)
8
Fig. P-01 Assembly Location Diagram
609
Ver. 1.1 DEC 2006
DP-8060/8045/8035
Safety
Ref. No. Part Number Part Name Serial Number / Remarks
Mark
DA-SP41-PU
YA1020K251
For DP-8035/8045
16900 Puncher Assembly
DA-SP41-PB
YA1020K252
For DP-8035/8045
See Note
16901 YA1020K395C Puncher Controller PCB Assembly
For DP-8035/8045
16902 YA1020P537 IC, CPU M38034M4-362SP See Note
See Note
16903 E323000483 IC, EP-ROM S-93C46ADP
For DP-8035/8045
16904 4A1-8685-000 Shutter, Puncher
(CNJ1004, J2004)
16905 YA1033K374 Harness, Power Connecting
For DP-8035/8045
(CNJ1003, J2003)
16906 YA1033K375 Harness, Interface
For DP-8035/8045
16907 4A1-8683-000 Spring, Tension
(CNJ1006, J2007-J2009)
16908 YA1033K372 Harness, Sensor
For DP-8035/8045
16910 4A1-8702-000 Label, "Puncher Dial"
16911 YA1020P789 Mount, Puncher
16912 4A1-8673-000 Cover, Harness
16913 4H1-6537-000 Dust LED PCB Unit (CNJ2005)
(CNJ2006)
16914 YA1020K369 Dust PTR PCB Unit
For DP-8035/8045
16915 4A1-8679-000 Gear, 16T/33T
16916 4A1-8680-000 Gear, 19T/32T
16917 4A1-8681-000 Duct, Puncher
16919 4A1-8686-000 Panel, Dust Box
16920 4A1-8687-000 Cover, Dust Box
(M2P, CNJ1001)
16921 YA1020K303 Motor, Stepping
For DP-8035/8045
(CNJ1005, J2005, J2006)
16922 YA1033K373 Harness, Dust Sensor
For DP-8035/8045
16923 4A1-8704-000 Cover, Puncher Base
16924 XB1-2400-605 Screw, M4 x 6 Truss Head Mach.
16925 XB4-7300-805 Screw, M3 x 8 Truss Head Tapping
16926 XD1-1104-629 Shim
16927 030060FZSW Screw, M3 x 6 W/Washer
16928 4F1-1850-000 Base
16929 4A1-8684-000 Bracket, Sensor
16930 4A1-8689-000 Filter
(PI2P, CNJ2007)
5111 E314000729 IC, Photo-Interrupter TLP1241
For DP-8035/8045
15704 FC2-2120-000 Screw, M4 x 7
610
Ver. 1.1 DEC 2006
DP-8060/8045/8035
A B C D E
16924 1
16917
See Fig. P-05
16907
(J1005)
16922 2
16925
16925 16910
16925
16912 (J2006)
16930 5
16914
16924 16920
16911
16904
6
16923
(J2005)
16913
16925 16925
7
16900 16919
8
Fig. P-02 Puncher Assembly
Note
This assembly does not include the parts shown with key No. 16901, 16902, and 16903.
611
Ver. 1.1 DEC 2006
DP-8060/8045/8035
Safety
Ref. No. Part Number Part Name Serial Number / Remarks
Mark
17000 NPN Puncher Total Assembly
17001 4A1-8688-000 Roller, Puncher
(CNJ1007, J2010, J2011)
17002 YA1033K371 Harness, Registration Sensor
For DP-8035/8045
17005 4A1-8682-000 Cover, Registration
17010 4A1-8692-000 Cover, Jam Clearing
17012 4A1-8701-000 KNOB, Jam Clearing
DA-SP41-PU
YA1020K592
For DP-8035/8045
17013 Punch Unit
DA-SP41-PB
YA1020K593
For DP-8035/8045
(M1P, CNJ2002)
17014 YA1033K300 Motor, DC
For DP-8035/8045
(CNJ1002, J2002)
17015 YA1033K376 Harness, Motor
For DP-8035/8045
(CNJ2010)
17016 YA1020K363 PCB Unit
For DP-8035/8045
(CNJ2011)
17017 YA1020K365 PCB Unit
For DP-8035/8045
17018 4A1-8705-000 Plate, Right Stirring
17019 4A1-8706-000 Plate, Left Stirring
17023 XB4-7301-209 Screw, M3 x 12 Truss Head Tapping
17026 XB1-2300-505 Screw, M3 x 5 Truss Head Mach.
17027 XB1-2400-805 Screw, M4 x 8 Truss Head Mach.
17028 4A1-8690-000 Sensor Bracket
17029 FB1-5969-000 Bearing
17030 FB5-5807-000 Mylar, Punch
17031 030050FWBI Screw, Motor
(PI1P, 3P, CNJ2008, J2009)
5111 E314000729 IC, Photo-Interrupter TLP1241
For DP-8035/8045
5413 XD2-1100-502 E-Ring
5511 XD2-1100-642 E-Ring
6409 FS1-9102-000 Screw, M3 Stepped
6431 FS5-6528-000 Roller
7610 FB5-6775-000 Encoder, F1350
7611 FB5-5968-000 Rack, Slide
7616 FF6-0507-000 Holder, Upper Sensor
7617 FF6-0508-000 Holder, Lower Sensor
7623 XB2-4300-805 Screw, M3 x8 W/Washer
16756 XB1-2300-605 Screw, M3 x 6 Truss Head Mach.
16925 XB4-7300-805 Screw, M3 x 8 Truss Head Tapping
612
Ver. 1.1 DEC 2006
DP-8060/8045/8035
A B C D E
5111 17015 2
(PI3P)
(J2009)
5111
(J1002)
(PI1P) (J2002)
17027 (J2008)
17028
(M1P) 3
7623 5511
7610 (J2002)
6409 7611 17013
6431
5413
17012
17014
17029 17002 4
16756 17001
6409 (J1007)
17026 17023
17031
17019
(J2011)
17005
7617 5
17018 17030 17010
6409
17001 (J2011) (J2010)
16756 (J2010)
17001
6409 17017
17016
16925 6
7616
16756
16925
7
8
Fig. P-03 Puncher Total Assembly
613
Ver. 1.1 DEC 2006
DP-8060/8045/8035
Safety
Ref. No. Part Number Part Name Serial Number / Remarks
Mark
NPN List Of Connectors
PCB DC Controller
J1001
NPN Registration Motor (M2P)
PCB DC Controller
J1002
YA1033K376 Harness, Motor For DP-8035/8045
PCB DC Controller
J1003
YA1033K375 Harness, Interface For DP-8035/8045
PCB DC Controller
J1004
YA1033K374 Harness, Power Connecting For DP-8035/8045
PCB DC Controller
J1005
YA1033K373 Harness, Dust Sensor For DP-8035/8045
PCB DC Controller
J1006
YA1033K372 Harness, Sensor For DP-8035/8045
PCB DC Controller
J1007
YA1033K371 Harness, Registration Sensor For DP-8035/8045
NPN Punch Motor (M1P)
J2002
YA1033K376 Harness, Motor For DP-8035/8045
SYS Saddle Finisher
J2003
YA1033K375 Harness, Interface For DP-8035/8045
SYS Saddle Finisher
J2004
YA1033K374 Harness, Power Connecting For DP-8035/8045
PCB Dust LED
J2005
YA1033K373 Harness, Dust Sensor For DP-8035/8045
PCB Dust PTR
J2006
YA1033K373 Harness, Dust Sensor For DP-8035/8045
NPN Slide Home Position Sensor (PI2)
J2007
YA1033K372 Harness, Sensor For DP-8035/8045
NPN Punch Home Position Sensor (PI1)
J2008
YA1033K372 Harness, Sensor For DP-8035/8045
NPN CLOCK Sensor (PI3)
J2009
YA1033K372 Harness, Sensor For DP-8035/8045
PCB Registration PTR
J2010
YA1033K371 Harness, Registration Sensor For DP-8035/8045
PCB Registration LED
J2011
YA1033K371 Harness, Registration Sensor For DP-8035/8045
614
Ver. 1.1 DEC 2006
DP-8060/8045/8035
A B C D E
J1007
J2002
2
J2004
J2011 J2003
J1001
J1002
J1003 3
J1004
J2010
J2008 J1005
J2009
5
J2007
J1006
J2006 6
J2005 7
8
Fig. P-04 List of Connectors
615
Ver. 1.1 DEC 2006
DP-8060/8045/8035
Safety
Ref. No. Part Number Part Name Serial Number / Remarks
Mark
NPN List Of Electric Parts
1 YA1020K395C Puncher Controller PCB Assembly For DP-8035/8045
2 4H1-6508-000 PCB Unit
3 YA1020K363 PCB Unit For DP-8035/8045
4 4H1-6538-000 Dust PTR PCB Unit
5 YA1020K367 Dust LED PCB Unit For DP-8035/8045
4K1-1077-000
M1P Motor, DC
YA1033K300
M2P YA1020K303A Motor, Stepping For DP-8035/8045
PI1P E314000729 IC, Photo-Interrupter TLP1241 For DP-8035/8045
PI2P E314000729 IC, Photo-Interrupter TLP1241 For DP-8035/8045
PI3P E314000729 IC, Photo-Interrupter TLP1241 For DP-8035/8045
616
Ver. 1.1 DEC 2006
DP-8060/8045/8035
A B C D E
PI3P
PI1P
PI2P
[1]
[4] 4
[2]
[3]
[5] 5
M1P
M2P
8
Fig. P-05 List of Electric Parts
617
Ver. 1.1 DEC 2006
DP-8060/8045/8035
XB1–2 4 00 –6 09
Classification symbol ....................... Binding head machine screw
Material and surface treatment ........ Steel (black zinc plated) See table 1.
XB7–1 0 80 –4 09
Classification symbol ....................... Socket head cap screw
Material and surface treatment ........ Steel (black zinc plated) See table 1.
Table 1
618
Ver. 1.1 DEC 2006
DP-8060/8045/8035
A-H
d
Flat Head Machine Screws Binding Head Self-Tapping Screws
d
d
B. Pan Head Machine Screws
Flat Head Self-Tapping Screws
d
d
E. Binding Head Machine Screws H. Pan Head Machine Screws with
Captive Spring Washer
d
619
Ver. 1.1 DEC 2006
DP-8060/8045/8035
class 1 class 3
d
L. Hex Socket Setscrews and
Socket Head Cap Screws How to Read Part Numbers
Hex Socket Setscrews
XB7–2 1 00 –3 09
Normal diameter (d) ....... M3
d
620
Ver. 1.1 DEC 2006
DP-8060/8045/8035
N -T
t XD1–1 1 02 –6 25
Inner diameter (d) ......... 2.6mm
* Material : Brass
D (mm)
d (mm)
Class 1 Class 2 Class 3
1.5 – 2.6 3.2
1.8 2.7 3.1 3.7
2.1 3.2 3.6 4.2
2.3 3.6 4 4.6
2.6 4 4.4 5
3.1 4.6 5 5.6
3.6 5.4 5.8 6.4
4.1 5.7 6.6 8
4.6 6.4 7.4 9 Thickness Code t (mm)
5.2 7.2 8.2 10 0 0.05
5.7 7.8 9 11 1 0.1
6.2 8.5 9.8 12 2 0.2
6.7 9.2 10.5 13 3 0.3
7.2 10 11.4 14 4 0.4
7.7 10.6 12.2 15 5 0.5
8.2 11.4 13 16 6 0.6
8.7 12 13.8 17 7 0.7
9.2 12.8 14.6 18 8 0.8
9.7 13.5 15.4 19 9 1
Table 2 Table 3
621
Ver. 1.1 DEC 2006
DP-8060/8045/8035
XD1–2 1 00 –3 07
Inner diameter (d) ......... 3.0mm
d
Plain washer Material and surface
treatment .......................Steel (nickel plated)
XD1–3 1 00 –5 07
Inner diameter (d) ......... 5.0mm
d
Spring washer Material and surface
treatment .......................Steel (nickel plated)
622
Ver. 1.1 DEC 2006
DP-8060/8045/8035
V -W
V. E-Rings
How to Read Part Numbers
XD2–1 1 00 –1 72
Inner diameter (d) ......... 1.7 mm
E-Ring
Material and surface treatment
W. Grip Rings
How to Read Part Numbers
XD2–2 1 00 –5 02
Inner diameter (d) ......... 5.0 mm
d
Grip ring
Material and surface
treatment .......................Stainless
(without surface treatment)
623
Ver. 1.1 DEC 2006
DP-8060/8045/8035
X. C-Rings
How to Read Part Numbers
Internal Type
Hole
Table 5
624
Ver. 1.1 DEC 2006
DP-8060/8045/8035
Y-Z
V. Pins
XD3–1 2 00 –1 22
Nominal diameter (D) ....................... 2.0 mm
XD3–2 2 00 –0 82
Nominal diameter (d) ....................... 2.0 mm
VI. Spacers
Z. Spacer
How to Read Part Numbers
XZ1–1 3 00 –3 0 5
Nominal diameter (d) ....................... 3.0 mm
625
Ver. 1.1 DEC 2006
DP-8060/8045/8035
626
Ver. 1.1 DEC 2006
DP-8060/8045/8035
627
Ver. 1.1 DEC 2006
DP-8060/8045/8035
628
Ver. 1.1 DEC 2006
DP-8060/8045/8035
629
Ver. 1.1 DEC 2006
DP-8060/8045/8035
630
Ver. 1.1 DEC 2006
DP-8060/8045/8035
631
Ver. 1.1 DEC 2006
DP-8060/8045/8035
632
Ver. 1.1 DEC 2006
DP-8060/8045/8035
633
Ver. 1.1 DEC 2006
DP-8060/8045/8035
634
Ver. 1.1 DEC 2006
DP-8060/8045/8035
635
Ver. 1.1 DEC 2006
DP-8060/8045/8035
636
Ver. 1.1 DEC 2006
DP-8060/8045/8035
637
Ver. 1.1 DEC 2006
DP-8060/8045/8035
638
Ver. 1.1 DEC 2006
DP-8060/8045/8035
639
Ver. 1.1 DEC 2006
DP-8060/8045/8035
640
Ver. 1.1 DEC 2006
DP-8060/8045/8035
641
Ver. 1.1 DEC 2006
DP-8060/8045/8035
642
Ver. 1.1 DEC 2006
DP-8060/8045/8035
643
Ver. 1.1 DEC 2006
DP-8060/8045/8035
644
Ver. 1.1 DEC 2006
DP-8060/8045/8035
645
Ver. 1.1 DEC 2006
DP-8060/8045/8035
646
Ver. 1.1 DEC 2006
DP-8060/8045/8035
647
Ver. 1.1 DEC 2006
DP-8060/8045/8035
648
Ver. 1.1 DEC 2006
DP-8060/8045/8035
649
Ver. 1.1 DEC 2006
DP-8060/8045/8035
650
Ver. 1.1 DEC 2006
DP-8060/8045/8035
651
Ver. 1.1 DEC 2006
DP-8060/8045/8035
652
Ver. 1.1 DEC 2006
DP-8060/8045/8035
653
Ver. 1.1 DEC 2006
DP-8060/8045/8035
654
Ver. 1.1 DEC 2006
DP-8060/8045/8035
655
Ver. 1.1 DEC 2006
DP-8060/8045/8035
656
Ver. 1.1 DEC 2006
DP-8060/8045/8035
657
Ver. 1.1 DEC 2006
DP-8060/8045/8035
658
Ver. 1.1 DEC 2006
DP-8060/8045/8035
659
Ver. 1.1 DEC 2006
DP-8060/8045/8035
660
Ver. 1.1 DEC 2006
DP-8060/8045/8035
661
Ver. 1.1 DEC 2006
DP-8060/8045/8035
662
Ver. 1.1 DEC 2006
DP-8060/8045/8035
663
Ver. 1.1 DEC 2006
DP-8060/8045/8035
664
Ver. 1.1 DEC 2006
DP-8060/8045/8035
665
Ver. 1.1 DEC 2006
DP-8060/8045/8035
666
Ver. 1.1 DEC 2006
DP-8060/8045/8035
667
Ver. 1.1 DEC 2006
DP-8060/8045/8035
668
Ver. 1.1 DEC 2006
DP-8060/8045/8035
669
Ver. 1.1 DEC 2006
DP-8060/8045/8035
670
Ver. 1.1 DEC 2006
DP-8060/8045/8035
671
Ver. 1.1 DEC 2006
DP-8060/8045/8035
672
Ver. 1.1 DEC 2006
DP-8060/8045/8035
673
Ver. 1.1 DEC 2006
DP-8060/8045/8035
674
Ver. 1.1 DEC 2006
DP-8060/8045/8035
675
Ver. 1.1 DEC 2006
DP-8060/8045/8035
676
Ver. 1.1 DEC 2006
DP-8060/8045/8035
677
Ver. 1.1 DEC 2006
DP-8060/8045/8035
678
Ver. 1.1 DEC 2006
DP-8060/8045/8035
679
Ver. 1.1 DEC 2006
DP-8060/8045/8035
680
Ver. 1.1 DEC 2006
DP-8060/8045/8035
681
Ver. 1.1 DEC 2006
DP-8060/8045/8035
682
Ver. 1.1 DEC 2006
DP-8060/8045/8035
683
Ver. 1.1 DEC 2006
DP-8060/8045/8035
684
Ver. 1.1 DEC 2006
DP-8060/8045/8035
685
Ver. 1.1 DEC 2006
DP-8060/8045/8035
686
Ver. 1.1 DEC 2006
DP-8060/8045/8035
687
Ver. 1.1 DEC 2006
DP-8060/8045/8035
688
Ver. 1.1 DEC 2006
DP-8060/8045/8035
689
Ver. 1.1 DEC 2006
DP-8060/8045/8035
690
Ver. 1.1 DEC 2006
DP-8060/8045/8035
691
Ver. 1.1 DEC 2006
DP-8060/8045/8035
692
Ver. 1.1 DEC 2006
DP-8060/8045/8035
693
Ver. 1.1 DEC 2006
DP-8060/8045/8035
694
Ver. 1.1 DEC 2006
DP-8060/8045/8035
695
Ver. 1.1 DEC 2006
DP-8060/8045/8035
696
Ver. 1.1 DEC 2006
DP-8060/8045/8035
697
Ver. 1.1 DEC 2006
DP-8060/8045/8035
698
Ver. 1.1 DEC 2006
DP-8060/8045/8035
699
Ver. 1.1 DEC 2006
E