You are on page 1of 61

SINGLE CHAMBER UNFIRED PRESSURE VESSEL - WORKBOOK VERSION: 09222018b

CALCULATIONS FOR ASME CODE SECTION VIII, DIVISION I, 2017 EDITION


Note: Save copies in the older (xls) version of Excel for best results.
This workbook is for Vertical or Horizontal single chamber vessels. Since I have made major changes and corrections to sheets that were from other
sources such as the web, I removed any company references before adapting them to interface with the complete workbook.
My advice is to use this workbook a master and then work in copies only. Making entries directly in sheet may overide formulas.

I've added the UW-16.1 table to the "Flanges & pipe" sheet in the "Coupling" area. It calculate coupling wall thickness for you with warnings.
"Extra Nozzles" sheet has been changed to allow nozzles in the shells, boot, and secondary heads. "Extra Head A&B Nozzles" are for heads A&B only.
Extra nozzle weights are not added to the vessel calculated weight, you must allow for it.
The Workbook allows either I.D. or O.D. shells and heads. You must enter either the I.D. or the O.D. on the cover page, but not both.
PLEASE NOTE THAT YOU SHOULD PRESS THE "F9" KEY AFTER NOZZLE REINFORCEMENT ENTRIES, Excel has a problem with large workbooks.
You make entries mainly on the "COVER PAGE" and "WORKSHEET" tabs below. Please re-set the reinforcement material to "INHERENT" when not used.
Information is distributed to the calculating page (tabs) and results show on both the "tab" page and "WORKSHEET". Remember to press F9.
The pages are protected to keep the formulas safe, but you can remove the protection to make changes with "Tools". There is no password.

Make your changes (entries) in the "yellow" areas. There are comment flags to help you. You must enter types and thickness for Head A and Head B.
There are drop down selections for the type of head. If you choose "WELD CAP" for head A, the workbook will default to WELD CAP throughout the book.
If needed you can change the Dish and Knuckle radius of the F&D heads. Nozzles are calculated as being in the center 80% of the heads.
If you select "F" for forged shell, the elliptical heads will be treated as forged with no thin-out. Weld caps are caluclated as 2:1 ellipticals with 12.5%
undertolerance applied. Note that the weld cap thickness and shell thickness must be the same and will have the same pressure rating.
There are sheets to compute the thickness required for flat heads and bolt on flat heads based on UG-34 and cones based on Appendix 1-5.
When a Cone is selected as a Head, Head A Nozzle 3 and Head B Nozzle 2 are reserved as a nozzle in the cone's small end or an elliptical head on the cone.
If no nozzle is used in the small end of the cone, a head will be calculated to seal it off. NOTE: The cone long seam efficiency will default to that of the shell.
If you are going to have a CONE, you should fill in the YELLOW areas of the CONE sheet first. Otherwise some flags will pop up.
You may have a shell attached to the small end of the cone by entering the length of that shell in the Shell #2 sheet. You must choose the location of the
nozzles in Shell #1, Shell #2, or the side of the Cone by selecting the location. Head A & B nozzles locations may be located in the head or cone by selecting
the location. If you need more nozzles you can use & copy the "Extra nozzles" sheet. These sheets will not be supported by the WORKSHEET.
Please note that only original shell, heads and nozzles are calculated in the "VESSEL COSTING" sheet since it gets information from the "WORKSHEET" only.
If a material is not listed in the drop down menu, you can unprotect the sheet and change the Data Validation for the cell to "Any" and enter a material.
NOTE: WHEN A CONE IS SELECTED ENTRIES MUST BE MADE IN THE "CONE", "HEAD on CONE", and "SHELL #2" SHEETS IF USED. You must
also enter the distance from the Large Outside Diameter of the cone for nozzles in the side of a cone on the sheet for that nozzle. Tangent or offset nozzles
may be entered in Shell nozzles 2 thru 5, Head A nozzles 1 & 2, and Head B nozzle 1. You must enter the offset on the nozzle worksheet page.
If a swing bolt closure is being used, you must complete all entries in the "Closure" sheet. The closure may be attached to a cone, shell, or nozzle"

Shell #2 and Head on cone may be used as a boot on a horizontal vessel by making direct inputs on their sheets.

Note: You must complete the Cone, Flat head, Shell #2, and/or Closure worksheets before designing the nozzles when they are used.
There are warning flags to help keep you from making mistakes. Remember to tell the sheet when you are using pipe, so it can derate the 12 1/2%.
Please note that 2.375" I.D. and smaller do not require reinforcement calculations, more information is provided at the bottom of the "WORKSHEET".
Also note that when tangent nozzles are used, if the larger developed opening is greater than 2x the smaller, extra calculations are required.
Note: UG-36 (3)(-c) no two isolated unreinforced openings shall have their centers closer to each other than the sum of their diameters.

Girth weld joint efficiency has to be entered manually on the "Shell" and "Shell #2" sheets.
Lifting lugs, baseplate, and skirt calculations for vertical vessels are done in the "Tower" sheet. It requires extra entries (see the yellow sections).
Buckling calculations are performed for towers on the Tower sheet. Note that large diameter thin wall horizontal vessels should be analized for buckling also.

To print your results just go to the tabs you need to print and print them. Each tab is formatted to print, page print areas are already set.

For your information, there is a "Material Database" tab. Pipe/flange information is on the bottom of the "WORKSHEET" and in the "Flanges & pipe" tab.
There has been 35 material specifications added to the 2017 Code. That material has not been added to the database you will need to add them manually.
When using an Android tablet you type in the material type like it is found in the material database, the stress value will auto fill (if it is in the database).

Shell external pressure may be calculated using the "SHELL EXTERNAL" tab. You can change the length of the shell to determine how
many re-inforcement rings (if any) are needed. I did not include the ring calculations. You must use the included charts for values "A" and "B".

I have modified the nozzle sheets to zero out left over reinforcement inputs if you forget to delete them on the WORKSHEET when not needed.
There is drop down menu for flanges and couplings in the Nozzle area. For size enter the nominal pipe size, the O.D. will be calculated. Long weld neck and
couplings O.D. and thickness is calculated for you. If you select "OTHER" for Nozzle thickness you will be prompted to enter the nozzle O.D. (in Blue) and enter
the I.D. instead on NPS. Flange pressure ratings are calculated for SA-105N and 316/316L (dual grade) materials only. Note: Flange pressure rating are calculated
from -20F to 600F, above 600F is approximate only. Nozzles are calculated for Shell, Elliptical Head, F&D Head, Elliptical of Weld Cap, and on Cone. Nozzles in
Cone are calculated for information only by this workbook and may not totally comply with ASME Code Section VIII Div, 1. If you select "OTHER", the flange
pressure rating calculations are by-passed. You may use rolled plate or a forging for a nozzle neck by selecting "OTHER" then in the Nozzle sheet change the efficiency.
For couplings larger than 2" please select "OTHER" for the nozzle thickness and enter the pipe O.D. as the I.D. and the coupling O.D. from the coupling chart.
Welding time calculations are for comparison purposes only so you can see the impact of changes in your design. Head seams are included on shells and cones.

WRC 107 Nozzle external loading may be performed for each nozzle. Just select the nozzle from the menu apply the loads and print. If a repad is needed,
you can unprotect the nozzle sheet and add the repad.

Nozzle and flange weights have been added to the nozzle pages. There is a weight overide block that will allow you to insert a fabricated flange weight.
The Flat Head sheet may be used to calculate a self-energizing o-ring flange.

Saddle calculations for large diameter horizontal vessels are done in the "SADDLE" sheet. Wind and Seismic forces are not considered.
I am not satisfied with the "Buckling" calculations on the Tower worksheet, so you wll see an alert to run FEA for buckling.

Please note that you need to consider a number of Code requirements that are not addressed in this Workbook. I advise checking for any Section VIII Mandatory
Appendix that might apply that is not considered on the Nozzle worksheets. There are also changes in Section II and Section IX of the code addressing
Charpy _V-Notch testing or other toughness testing. Please make sure your material and welding procedures comply with these changes.
NDE requrements have also changed in the 2017 Edition. You can review the changes in the Code at the link below.
https://global.ihs.com/images/ENGL/2017_bpvc_key_changes_web.pdf

Version 9222018b has the flange stud information added to the "Flanges & pipe" sheet.

Disclaimer:
I strongly suggest that you check the results given by this worksheet. I assembled this information to assist in estimating vessels.
Final design of any vessel should be done with the appropriate software or by a qualified engineer. This workbook is not for sale, but may be distributed freely.

All sheets in this workbook have been reviewed against full ASME Code Section VIII Division 1 Edition 2013, Edition 2015, and Edition 2017, ASME B16.5,
ASME B31.3, and/or Megyesy's Pressure Vessel Handbook for accuracy. Please email me at charlesirwin@outlook.com with any comments or complaints.
"Version 09222018a" is the latest update with ASME BPVC-2017 code compliance check performed on 09/25/2018 by QCM Charles Irwin.
Spreadsheet formulas have been manually calculated to verify accuracy.

You can find more useful spreadsheets at www.pveng.com. Some of the sheets here are modified versions of sheets found there.
YOUR COMPANY NAME
ADDRESS
CITY, STATE ZIP CODE

ASME CODE SECTION VIII, DIVISION I


2017 EDITION
PRESSURE VESSEL CALCULATIONS
WORKBOOK VERSION: 09222018b

Customer name:

VESSEL O.D. 0 INCH 0


VESSEL I.D. 0 INCH 0
SHELL S/S LENGTH 0 INCH 0

VESSEL ORIENTATION HORIZONTAL VERTICAL


HORIZONTAL

JOB NO. Drawing no:

NAMEPLATE INFORMATION

Vessel MAWP: 0 PSIG ALERT -- Below Code requirement


Design Temperature: 0 F INCREASE
Min. Temperature 0 F
Serial Number:
National Board No. NONE
Year Built: 2018
Radiography: NONE
Post Weld Heat Treat NONE
Construction Type: W
Special Type:
Corrosion Allowance 0 INCH

Signature(s):

Date: ###

Date:

Remarks:

Note: Metric, Centigrade, Bar, and Mpa entries will be converted to Inch, Fahrenheit, and PSIG on worksheets.
YOUR COMPANY NAME 10/24/2018 ENTRY AREA WELDING 0.00 (HOURS) NONE
RESULTS AREA WIRE MESH
TYPE JOB NO. 0 MIST EXTRACTOR TYPE: NONE VANE
CUSTOMER NAME 0 LIFTING LUG (4:1 SAFETY FACTOR) MANHOURS 0 SA-36
VESSEL DESIGN SUMMARY HOLE DIAMETER 0 INCH 0 SA-516 70
DESIGN TEMPERATURE (COVER Pg) F. 0 0 OUTSIDE RADIUS 0 INCH 0
(See Material Database temperature ratings.) #N/A MIN.SHELL THICKNESS MATERIAL NONE SA-106 B
VESSEL SHELL O.D. (COVER Pg) 0.00 INCH LUG STRESS VALUE #N/A PSI SA-106 C
VESSEL SHELL I.D. (COVER Pg) 0.00 INCH VESSEL WEIGHT 0 LBS SA-234 WPB
MAIN SHELL S/S LENGTH (COVER Pg) 0.00 INCH SHELL S/S LENGTH DESIGN THICKNESS (MIN) #N/A INCH SA-105
NUMBER OF MAIN SHELL CYLINDERS 1 (DETERMINES GIRTH SEAMS) REQUIRED WELD (CODE) #N/A INCH SA-312 TP304
NUMBER OF SHELL LONG SEAMS 0 (0) FOR PIPE SHELLS (F) FORGING REQUIRED WELD (LOAD) 0.000 INCH SA-312 TP304L
DESIGN PRESSURE (COVER Pg) 0.00 PSIG ERROR
STATIC HEAD PRESSURE 0.00 PSIG HYDROTEST PRESSURE 0 PSIG ERROR
VESSEL ORIENTATION HORIZONTAL H SA-240 304
SHELL MATERIAL INHERENT PIPE #N/A CURVE 'A' MATERIAL SA-240 304L
SHELL STRESS VALUE #N/A PSI Impact testing exempt to -20F per UG20(f) SA-240 316
SHELL THICKNESS 0.0000 INCH #N/A #N/A PSIG MAX CURVE "B" CURVE "D" SA-240 316L
SHELL JOINT EFF. 85% UCS-66 MIN. TEMP - SHELL #N/A #N/A SA-403 304
HEAD (A) MATERIAL SA-36 FOR HEADS AND NOZZLES SEE MATERIAL SHEET SA-403 304L
HEAD (A) STRESS VALUE 16,600 PSI #N/A
HEAD A (TOP/END) TYPE/THICKNESS ELLIPTICAL 0.0000 INCH 0 PSIG MAX ERROR 0
HEAD A JOINT EFF. 85% Check Code requirement ###
HEAD (B) MATERIAL SA-36 ###
HEAD (B) STRESS VALUE 16,600 PSI #N/A
HEAD B (BOT/END) TYPE/THICKNESS ELLIPTICAL 0.0000 INCH 0 PSIG MAX ERROR 0
HEAD B JOINT EFF. 85%
CORROSION ALLOWANCE (COVER Pg) 0.000 INCH 0
SHELL VOLUME 0.00 CUFT 0.00 GAL SEPARATOR CAPACITY 0% FLOODED 0
HEAD VOLUME 0.00 CUFT 0.00 GAL RETENTION TIME 0 MINUTES
TOTAL VOLUME 0.00 CUFT 0.00 GAL TWO PHASE #DIV/0! Bbl/D ###
TOTAL DRY WEIGHT 0 LBS THREE PHASE #DIV/0! Bbl/D UCS-56 HEAT TR
HYDROTEST WEIGHT 0 LBS VESSEL WEIGHT w/ WET SAND 0 LBS

NOZZLES IN SHELLS OR CONE SIDE NOZZLES IN HEADS OR CONES ###


UG-36 MAX. SHELL NOZZLE I.D. SIZE (INCH) 0.000 0 0 HEAD A (END) ELLIPTICAL ###
NOZZLE 1 -- NOT USED 0.0000 INCH/PSI 0 HEAD A NOZZLE 1 -- NOT USED 0.0000 INCH/PSI 0
DESCRIPTION/SIZE (IN) OTHER 0 INCH I.D. DESCRIPTION/SIZE (IN) OTHER 0 INCH I.D.
NUMBER OF NOZZLES 0 NUMBER OF NOZZLES 0
NOZZLE MATERIAL INHERENT NOZZLE MATERIAL INHERENT
STRESS VALUE 0 PSI STRESS VALUE 0 PSI
PIPE (1) FORGING/PLATE (0) 0 TYPE ENTER O.D PIPE (1) FORGING (0) 0 TYPE ###
NOZZLE THICKNESS OTHER INCH 0.000 0 NOZZLE THICKNESS CPLG/FLG INCH 0.000 ###
EXTERNAL PROJECTION 0 INCH INCREASE EXTERNAL PROJECTION 0 INCH INCREASE ###
INTERNAL PROJECTION 0 INCH INTERNAL PROJECTION 0 INCH
CORROSION ALLOWANCE 0.0000 INCH CORROSION ALLOWANCE 0.0000 INCH REPAD S1
OUTSIDE FILLET WELD 0 INCH OUTSIDE FILLET WELD 0 INCH
INSIDE FILLET WELD 0 INCH INSIDE FILLET WELD 0 INCH
NOT USED LOCATION SHELL NOT USED LOCATION HEAD REPAD S4
WITH REPAD NOT USED WITH REPAD NOT USED REPAD S5
NUMBER OF NOZZLES 0 BLIND FLG N Y NUMBER OF NOZZLES 0 BLIND FLG N Y
REPAD MATERIAL INHERENT N REPAD MATERIAL INHERENT N
STRESS VALUE 0 PSI INCREASE STRESS VALUE 0 PSI INCREASE
THICKNESS 0 INCH THICKNESS 0 INCH
REPAD O.D. 0 INCH INCREASE REPAD O.D. 0 INCH INCREASE
REPAD OS FILLET WELD 0 INCH REPAD OS FILLET WELD 0 INCH
UG-27 UG-27
UG-45 Thickness (IN) 0.0000 UG-45 Thickness (IN) 0.0000 SA-36
MATERIAL REPLACEMENT MATERIAL REPLACEMENT SA-516 70
Tangent nozzles allowed - Sheet "SHELL NOZZLE 2" SA-240 304
NOZZLE 2 -- NOT USED 0.0000 INCH/PSI 0 HEAD A NOZZLE 2 -- NOT USED 0.0000 INCH/PSI 0 SA-240 304L
DESCRIPTION/SIZE (IN) OTHER 0 INCH I.D. DESCRIPTION/SIZE (IN) OTHER 0 INCH I.D.
NUMBER OF NOZZLES 0 NUMBER OF NOZZLES 0
NOZZLE MATERIAL INHERENT NOZZLE MATERIAL INHERENT 1500# FLANGE
STRESS VALUE 0 PSI STRESS VALUE 0 PSI 3000# CPLG
PIPE (1) FORGING (0) 0 TYPE ENTER O.D PIPE (1) FORGING (0) 0 TYPE ENTER O.D SA-36
NOZZLE THICKNESS OTHER INCH 0.000 NOZZLE THICKNESS OTHER INCH 0.000 SA-105
EXTERNAL PROJECTION 0 INCH INCREASE EXTERNAL PROJECTION 0 INCH INCREASE SA-516 70
INTERNAL PROJECTION 0 INCH INTERNAL PROJECTION 0 INCH
CORROSION ALLOWANCE 0.0000 INCH CORROSION ALLOWANCE 0.0000 INCH SA-240 304
OUTSIDE FILLET WELD 0 INCH OUTSIDE FILLET WELD 0 INCH
INSIDE FILLET WELD 0 INCH INSIDE FILLET WELD 0 INCH
NOT USED LOCATION SHELL NOT USED LOCATION ERROR SA-240 316L
WITH REPAD NOT USED WITH REPAD NOT USED SA-403 304
NUMBER OF NOZZLES 0 BLIND FLG N NUMBER OF NOZZLES 0 SA-403 304L
REPAD MATERIAL INHERENT REPAD MATERIAL INHERENT SA-403 316
STRESS VALUE 0 PSI INCREASE STRESS VALUE 0 PSI INCREASE
THICKNESS 0 INCH THICKNESS 0 INCH
REPAD O.D. 0 INCH INCREASE REPAD O.D. 0 INCH INCREASE
REPAD OS FILLET WELD 0 INCH REPAD OS FILLET WELD 0 INCH
UG-27 UG-27 SA-516 70
UG-45 Thickness (IN) 0.0000 UG-45 Thickness (IN) 0.0000 SA-53 EB
MATERIAL REPLACEMENT MATERIAL REPLACEMENT SA-106 B
SA-106 C
Tangent nozzles allowed - Sheet "SHELL NOZZLE 3" SA-312 TP304
NOZZLE 3 -- NOT USED 0.0000 INCH/PSI 0 HEAD A NOZZLE 3 -- NOT USED 0.0000 INCH/PSI 0 SA-312 TP304L
DESCRIPTION/SIZE (IN) OTHER 0 INCH I.D. DESCRIPTION/SIZE (IN) OTHER 0 INCH I.D.
NUMBER OF NOZZLES 0 NUMBER OF NOZZLES 0
NOZZLE MATERIAL INHERENT NOZZLE MATERIAL INHERENT SA-240 316
STRESS VALUE 0 PSI STRESS VALUE 0 PSI SA-240 316L
PIPE (1) FORGING (0) 0 TYPE ENTER O.D PIPE (1) FORGING (0) 0 TYPE ENTER O.D SA-240 304
NOZZLE THICKNESS OTHER INCH 0.000 NOZZLE THICKNESS OTHER INCH 0.000 SA-240 304L
EXTERNAL PROJECTION 0 INCH INCREASE EXTERNAL PROJECTION 0 INCH INCREASE SA-240 316
INTERNAL PROJECTION 0 INCH INTERNAL PROJECTION 0 INCH
CORROSION ALLOWANCE 0.0000 INCH CORROSION ALLOWANCE 0.0000 INCH NOZZLE 7
OUTSIDE FILLET WELD 0 INCH OUTSIDE FILLET WELD 0 INCH
INSIDE FILLET WELD 0 INCH INSIDE FILLET WELD 0 INCH
NOT USED LOCATION SHELL NOT USED LOCATION ERROR NOZZLE 10
WITH REPAD NOT USED WITH REPAD NOT USED
NUMBER OF NOZZLES 0 BLIND FLG N NUMBER OF NOZZLES 0 ###
REPAD MATERIAL INHERENT REPAD MATERIAL INHERENT ###
STRESS VALUE 0 PSI INCREASE STRESS VALUE 0 PSI INCREASE
THICKNESS 0 INCH THICKNESS 0 INCH
REPAD O.D. 0 INCH INCREASE REPAD O.D. 0 INCH INCREASE
REPAD OS FILLET WELD 0 INCH REPAD OS FILLET WELD 0 INCH
UG-27 UG-27 C
UG-45 Thickness (IN) 0.0000 UG-45 Thickness (IN) 0.0000 ###
MATERIAL REPLACEMENT MATERIAL REPLACEMENT ###
Tangent nozzles allowed - Sheet "SHELL NOZZLE 4" 1 HEAD B (END) ELLIPTICAL ###
NOZZLE 4 -- NOT USED 0.0000 INCH/PSI 0 HEAD B NOZZLE 1 -- NOT USED 0.0000 INCH/PSI 0 SHELL
DESCRIPTION/SIZE (IN) OTHER 0 INCH I.D. DESCRIPTION/SIZE (IN) OTHER 0 INCH I.D.
NUMBER OF NOZZLES 0 NUMBER OF NOZZLES 0
NOZZLE MATERIAL INHERENT NOZZLE MATERIAL INHERENT ###
STRESS VALUE 0 PSI STRESS VALUE 0 PSI ERROR
PIPE (1) FORGING (0) 0 TYPE ENTER O.D PIPE (1) FORGING (0) 0 TYPE ENTER O.D N/A
NOZZLE THICKNESS OTHER INCH 0.000 NOZZLE THICKNESS OTHER INCH 0.000 N/A
EXTERNAL PROJECTION 0 INCH INCREASE EXTERNAL PROJECTION 0 INCH INCREASE N/A
INTERNAL PROJECTION 0 INCH INTERNAL PROJECTION 0 INCH
CORROSION ALLOWANCE 0.0000 INCH CORROSION ALLOWANCE 0.0000 INCH
OUTSIDE FILLET WELD 0 INCH OUTSIDE FILLET WELD 0 INCH
INSIDE FILLET WELD 0 INCH INSIDE FILLET WELD 0 INCH
NOT USED LOCATION SHELL NOT USED LOCATION ERROR N/A
WITH REPAD NOT USED WITH REPAD NOT USED N/A
NUMBER OF NOZZLES 0 BLIND FLG N NUMBER OF NOZZLES 0 BLIND FLG N Y
REPAD MATERIAL INHERENT REPAD MATERIAL INHERENT N
STRESS VALUE 0 PSI INCREASE STRESS VALUE 0 PSI INCREASE
THICKNESS 0 INCH THICKNESS 0 INCH
REPAD O.D. 0 INCH INCREASE REPAD O.D. 0 INCH INCREASE
REPAD OS FILLET WELD 0 INCH REPAD OS FILLET WELD 0 INCH
UG-27 UG-27 ELLIPTICAL
UG-45 Thickness (IN) 0.0000 UG-45 Thickness (IN) 0.0000
MATERIAL REPLACEMENT MATERIAL REPLACEMENT
Tangent nozzles allowed - Sheet "SHELL NOZZLE 5" 1 CONE
NOZZLE 5 -- NOT USED 0.0000 INCH/PSI 0 HEAD B NOZZLE 2 -- NOT USED 0.0000 INCH/PSI 0 CLOSURE
DESCRIPTION/SIZE (IN) OTHER 0 INCH I.D. DESCRIPTION/SIZE (IN) OTHER 0 INCH I.D.
NUMBER OF NOZZLES 0 NUMBER OF NOZZLES 0
NOZZLE MATERIAL INHERENT NOZZLE MATERIAL INHERENT 3,500
STRESS VALUE 0 PSI STRESS VALUE 0 PSI NOZZLE 5
PIPE (1) FORGING (0) 0 INCH ENTER O.D PIPE (1) FORGING (0) 0 TYPE ENTER O.D NOZZLE 6
NOZZLE THICKNESS OTHER INCH 0.000 NOZZLE THICKNESS OTHER INCH 0.000 NOZZLE 7
EXTERNAL PROJECTION 0 INCH INCREASE EXTERNAL PROJECTION 0 INCH INCREASE NOZZLE 8
INTERNAL PROJECTION 0 INCH INTERNAL PROJECTION 0 INCH
CORROSION ALLOWANCE 0.0000 INCH CORROSION ALLOWANCE 0.0000 INCH NOZZLE 10
OUTSIDE FILLET WELD 0 INCH OUTSIDE FILLET WELD 0 INCH
INSIDE FILLET WELD 0 INCH INSIDE FILLET WELD 0 INCH
NOT USED LOCATION SHELL NOT USED LOCATION ERROR
WITH REPAD NOT USED WITH REPAD NOT USED
NUMBER OF NOZZLES 0 BLIND FLG N NUMBER OF NOZZLES 0
REPAD MATERIAL INHERENT REPAD MATERIAL INHERENT
STRESS VALUE 0 PSI INCREASE STRESS VALUE 0 PSI INCREASE
THICKNESS 0 INCH THICKNESS 0 INCH
REPAD O.D. 0 INCH INCREASE REPAD O.D. 0 INCH INCREASE
REPAD OS FILLET WELD 0 INCH REPAD OS FILLET WELD 0 INCH
UG-27 UG-27
UG-45 Thickness (IN) 0.0000 UG-45 Thickness (IN) 0.0000
MATERIAL REPLACEMENT MATERIAL REPLACEMENT
When tangent nozzles are used (Shell Nozzles 4&5, Head Nozzles A 1 &2, B 1), if the larger developed opening is greater than 2x the smaller, extra calculations are required.
UG-36 (3)(-c) no two isolated unreinforced openings shall have their centers closer to each other than the sum of their diameters.
Vessels with shell material greater than 1.25" nominal thickness require 100% RT of butt welds.
Vessels with CARBON STEEL shell material greater than 1.5" nominal thickness require 100% RT of butt welds and heat treatment.
Flange pressure ratings are for SA-105, SA-350 LF2, SA-516-70, SA-515-70,SA-181-70, SA-535-C1, SA-216-WCB, and SA-240 316/316L dual certified.
Nozzle calculations are not required for 2" pipe nozzles, however nozzle thickness must equal or exceed schedule 40 after corrosion allowance per UG-45.
Nozzle calculations are not required for 3" pipe nozzles in 1/4" or 3/8" wall vessels, however nozzle thickness must equal or exceed schedule 40 after corrosion allowance per UG-45.
Nozzle calculations are required for some coupling sizes when the corrosion allowance is applied to the I.D..

FOR COUPLING, PIPE, LONG WELD NECK, HB-LONG WELD NECK, AND FLANGE DETAIL SEE "Flanges & pipe" TAB. NOTE THAT NOT ALL "HB LWN" ARE LISTED.
YOUR COMPANY NAME
CALCULATIONS FOR ASME CODE SECTION VIII, DIVISION I, 2017 EDITION
PRESSURE VESSEL CALCULATIONS
WORKBOOK VERSION: 09222018b 10/24/2018

Nozzle location: NOT USED (Not Required) Page 1 of 2 #VALUE!


NOZZLE TYPE: OTHER 0 NPS
JOB NO: 0 NOZZLE ID. QUANTITY= 0
Shell/Head Inputs: FLANGE/COUPLING RATING 0 PSI
NONE Material
0 Sv [psi] - allowable stress
NONE E1 - efficiency of shell at nozzle
NONE Ds [in] - inside diameter of shell
NONE nt [in] - nominal shell wall thickness
NONE Treq [in] - required shell wall thickness
0.000 sca [in] - shell corrosion allowance
0.063 tUG16(b) [in] - minimum thickness per UG-16 b
Nozzle Inputs:
INHERENT Material
0 Sn [psi] - allowable stress
1.00 E - nozzle efficiency
0.000 Do [in] - outside diameter of nozzle
0.0000 Nwall [in] - nominal wall thickness of nozzle
0.000 Lp [in] - exterior projection of nozzle
0.000 Ip [in] - interior projection of nozzle
0.000 nca [in] - nozzle corrosion allowance
0.0% UTP [%] - undertolerance allowance
0.0 Pn [psi] - interior pressure

Reinforcement (check replacement area below):


INHERENT Material
0 Sp [psi] - allowable stress of repad
0.0000 te [in] - repad thickness 0.000
0.000 Dp [in] - outside diameter
0.000 Leg41 [in] - fillet size
0.000 Leg42 [in] - fillet size
0.000 Leg43 [in] - fillet size
0.000 LegG [in] - depth of groove
Variables:
UT [in] = Nwall*UTP 0*0 = 0.000
Rn [in] = Do/2 - (Nwall-nca) + UT 0/2 - (0-0) + 0 = 0.000
ti [in] = Nwall-2*nca 0-2*0 = 0.000
h [in] = MIN(Ip-sca,2.5*nt,2.5*ti) #VALUE! #VALUE!
tn [in] = Nwall-nca 0-0 = 0.000
d [in] = Do-2*tn 0-2*0 = 0.000
fr1 = MIN(Sn/Sv,1) MIN(0/0,1) = #DIV/0!
fr2 = MIN(Sn/Sv,1) MIN(0/0,1) = #DIV/0!
fr3 = MIN(Sn/Sv,Sp/Sv,1) MIN(0/0,0/0,1) = #DIV/0!
fr4 = MIN(Sp/Sv,1) MIN(0/0,1) = #DIV/0!
Required Thickness: UG-27(c)(1,2)
TreqN [in] = (Pn*Rn)/(Sn*E - 0.6*Pn)+nca ~~ required minimum thickness
(0*0)/(0*1 - 0.6*0)+0 = #DIV/0!
trnR [in] = (Pn*Rn)/(Sn*1 - 0.6*Pn) (0*0)/(0*1 - 0.6*0) = #DIV/0!
CheckTreqN = TreqN <= Nwall #DIV/0! #DIV/0!
UG-45:
Tstd [in] = thickness standard wall pipe VLOOKUP(0,PIpeWall,2) = #N/A
Nact [in] = Nwall * (1-UTP) 0 * (1-0) = 0.000
UG45 [in] = Max(UG45a, UG45b) ~~ required thickness per UG-45 #DIV/0! #DIV/0!
UG45a [in] = trnR + nca #DIV/0! #DIV/0!

Shell Nozzle 1 Page 2 of 2

UG45b [in] = Min(UG45b3,UG45b4) #VALUE! #VALUE!


UG45b1 [in] = Max(Treq+sca,tUG16(b) + sca) #VALUE! #VALUE!
UG45b2 [in] = 0 0= 0.000
UG45b3 [in] = Max(UG45b1,UG45b2) #VALUE! #VALUE!
UG45b4 [in] = Tstd*0.875 + nca #N/A #N/A
CheckUG45 = UG45 <= Nact #DIV/0!#DIV/0!
#DIV/0!
Minimum thickness per UG-45 [in] = #N/A #N/A

Area Replacement:
Ar [in^2] = 1*d*Treq*1+2*tn*Treq*1*(1-fr1) ~~ required Area
#VALUE! #VALUE!
A1 [in^2] = max(d, 2*(nt+tn)) * (E1*nt-1*Treq)-2*tn*(E1*nt-1*Treq)*(1-fr1)
#VALUE! #VALUE!
A2 [in^2] = min((tn-trnR)*fr2*min(5*nt,2*Lp),(tn-trnR)*(Min(2.5*tn+te,2*Lp)*fr2*2))
#DIV/0! #DIV/0!
A3 [in^2] = Min(5*nt*ti*fr2,5*ti*ti*fr2,2*h*ti*fr2)
#VALUE! #VALUE!
A5 [in^2] = (Dp-d-2*tn)*te*fr4 N/A = 0.000
A41 [in^2] = Leg41^2*fr3 #DIV/0! #DIV/0!
A42 [in^2] = Leg42^2*fr4 #DIV/0! #DIV/0!
A43 [in^2] = (Leg43-nca)^2*fr2 #DIV/0! #DIV/0!
Aa [in^2] = A1+A2+A3+A5+A41+A42+A43 ~~ actual area
#VALUE! #VALUE!
CheckA = Aa >= Ar ~~ check area replacement #VALUE! #VALUE!

Nozzle Weld Strength: per UW-16(a), (b)


Weld 41 tmin [in] = smaller of 0.75, nt, or Nwall 0.750 0.000 0.000 = 0.7500
Weld 41 Leg [in] = smaller of 0.25 or (tmin * 0.7) / 0.7 0.25 = 0.3571
0 >= 0.3571 = ERROR
Weld 42 tmin [in] = (smaller of 0.5nt or te) #VALUE! = 0.0000
Weld 42 Leg [in] = (smaller of 0.25 or (temin * 0.7) / 0.7) 0 = 0.0000
0 0 >= 0 = N/A
Weld 43 Leg [in] = (smaller of 0.25 or (tmin * 0.7) / 0.7) + sca = 0.0000
0 0 >= 0 = N/A

Nozzle Weld Strength: per UW-16(i) (using Weld 41 only)

Weld 41 + Weld 43 tmin [in] = smaller of 1.25 * nt, or Nwall (0.25" min)
0.000 0 * 1.25 = 0.0000
(using Weld 41 only) 0+0 >= 0 = Acceptable
0 >= 0.25 = ERROR

Minimum design temperature check: See Material Database sheet

Note: Attached piping to be externally supported. Calculations are limited to materials listed in this sheet.
YOUR COMPANY NAME
CALCULATIONS FOR ASME CODE SECTION VIII, DIVISION I, 2017 EDITION
PRESSURE VESSEL CALCULATIONS
WORKBOOK VERSION: 09222018b 10/24/2018

Head Nozzle and Repad Page 1 of 2


Head (A) or (B) NOT USED NOZZLE ID. 0.00 (minutes)
JOB NO: 0 QTY= 0 FLANGE/COUPLING RATING 0 PSI
Head Inputs: HEAD B (END) ELLIPTICAL (Nozzles within 80% limit only) Flange weld time
SA-36 Material 0.049 (CI/MIN)
16,600 Sv [psi] - allowable stress 0.00 (min total) 0
0.85 E1 - efficiency of head at nozzle
0.000 Ds [in] - inside head dish diameter
0.000 nt [in] - nominal head wall thickness Nozzle weld time
0.000 Treq [in] - required head wall thickness at nozzle 0.049 (CI/MIN)
0.000 sca [in] - shell/head corrosion allowance 0.00 0
0.063 tUG16(b) [in] - minimum thickness per UG-16 b 0.00 0
Nozzle Inputs: 0.00 (min total) 0
OTHER Type
INHERENT Nozzle material welded in head 0
16,600 Sn [psi] - allowable stress
1.00 E - nozzle efficiency
0.000 Do [in] - outside diameter of nozzle
0.000 Nwall [in] - nominal wall thickness of nozzle
0.000 Lp [in] - exterior projection of nozzle
0.000 Ip [in] - interior projection of nozzle
0.000 nca [in] - nozzle corrosion allowance
12.5% UTP [%] - undertolerance allowance
0.0 Pn [psi] - interior pressure
Reinforcement (check area replacement):
INHERENT Reinforcement pad material
16,600 Sp [psi] - allowable stress of repad Nozzle weld time
0.0000 te [in] - repad thickness 0.049 (CI/MIN) 0.000
0.000 Dp [in] - outside diameter 0.00 0
0.000 Leg41 [in] - fillet size 0.00 0
0.000 Leg42 [in] - fillet size 0.00 0
0.000 Leg43 [in] - fillet size ERROR 0.00 (min total) 0
0.000 LegG [in] - depth of groove 0
Variables:
UT [in] = Nwall*UTP 0*0.125 = 0.000
Rn [in] = Do/2 - (Nwall-nca) + UT 0/2 - (0-0) + 0 = 0.000
ti [in] = Nwall-2*nca 0-2*0 = 0.000
h [in] = MIN(Ip-sca,2.5*nt,2.5*ti) MIN(0-0,2.5*0,2.5*0) = 0.000
tn [in] = Nwall-nca 0-0 = 0.000
d [in] = Do-2*tn 0-2*0 = 0.000
fr1 = MIN(Sn/Sv,1) MIN(16600/16600,1) = 1.000
fr2 = MIN(Sn/Sv,1) MIN(16600/16600,1) = 1.000
fr3 = MIN(Sn/Sv,Sp/Sv,1) MIN(16600/16600,16600/16600,1) = 1.000
fr4 = MIN(Sp/Sv,1) MIN(16600/16600,1) = 1.000
Required Thickness: UG-27(c)(1,2)
TreqN [in] = (Pn*Rn)/(Sn*E - 0.6*Pn)+nca ~~ required minimum thickness
(0*0)/(16600*1 - 0.6*0)+0 = 0.000
trnR [in] = (Pn*Rn)/(Sn*1 - 0.6*Pn) (0*0)/(16600*1 - 0.6*0) = 0.000
CheckTreqN = TreqN <= Nwall 0 <= 0 = Acceptable
UG-45:
Tstd [in] = thickness stan thickness standard wall pipe VLOOKUP(0,PIpeWall,2) = #N/A
Nact [in] = Nwall * (1-UTP) 0 * (1-0.125) = 0.000
#N/A
UG45 [in] = Max(UG45a, UG45b) ~~ required thickness per UG-45 #N/A #N/A
UG45a [in] = trnR + nca 0 + 0 = 0.000
UG45b [in] = Min(UG45b3,UG45b4) #N/A #N/A

HEAD B (END) 0 Page 2 of 2

UG45b1 [in] = Max(Treq+sca,tUG16(b) + sca) MAX(0+0,0.063 + 0) = 0.063


UG45b2 [in] = 0 0= 0.000
UG45b3 [in] = Max(UG45b1,UG45b2) MAX(0.063,0) = 0.063
UG45b4 [in] = Tstd*0.875 + nca #N/A #N/A
CheckUG45 = UG45 <= Nact #N/A #N/A
#N/A
Minimum thickness per UG-45 [in] = #N/A #N/A

Area Replacement:
Ar [in^2] = 1*d*Treq*1+2*tn*Treq*1*(1-fr1) ~~ required Area
1*0*0*1+2*0*0*1*(1-1) = 0.000
A1 [in^2] = max(d, 2*(nt+tn)) * (E1*nt-1*Treq)-2*tn*(E1*nt-1*Treq)*(1-fr1)
MAX(0, 2*(0+0)) * (0.85*0-1*0)-2*0*(0.85*0-1*0)*(1-1) = 0.000
A2 [in^2] = min((tn-trnR)*fr2*min(5*nt,2*Lp),(tn-trnR)*(Min(2.5*tn+te,2*Lp)*fr2*2))
MIN((0-0)*1*MIN(5*0,2*0),(0-0)*(MIN(2.5*0+0,2*0)*1*2)) = 0.000
A3 [in^2] = Min(5*nt*ti*fr2,5*ti*ti*fr2,2*h*ti*fr2)
MIN(5*0*0*1,5*0*0*1,2*0*0*1) = 0.000
A5 [in^2] = (Dp-d-2*tn)*te*fr4 N/A = 0.000
A41 [in^2] = Leg41^2*fr3 0^2*1 = 0.000
A42 [in^2] = Leg42^2*fr4 0^2*1 = 0.000
A43 [in^2] = (Leg43-nca)^2*fr2 (0-0)^2*1 = 0.000
Aa [in^2] = A1+A2+A3+A5+A41+A42+A43 ~~ actual area
0+0+0+0+0+0+0 = 0.000
CheckA = Aa >= Ar ~~ check area replacement 0 >= 0 = Acceptable

Nozzle Weld Strength: per UW-16(a), (b)


Weld 41 tmin [in] = smaller of 0.75, nt, or Nwall 0.000 0.000 0.000 = 0.0000
Weld 41 Leg [in] = smaller of 0.25 or (tmin * 0.7) / 0.7 0 = 0.0000
0 >= 0 = ERROR
Weld 42 tmin [in] = (smaller of 0.5nt or te) 0.000 = 0.0000
Weld 42 Leg [in] = (smaller of 0.25 or (temin * 0.7) / 0.7) 0 = 0.0000
0 0 >= 0 = N/A
Weld 43 Leg [in] = (smaller of 0.25 or (tmin * 0.7) / 0.7) + sca 0 = 0.0000
0 0 >= 0 = N/A

Weld 41 + Weld 43 tmin [in] = smaller of 1.25 * nt, or Nwall (0.25" min)
0.000 0 * 1.25 = 0.0000
(using Weld 41 only) 0+0 >= 0 = Acceptable
0 >= 0.25 = ERROR

Minimum design temperature check: See Material Database sheet

Note: Attached piping to be externally supported. Calculations are limited to materials listed in this sheet.
YOUR COMPANY NAME
CALCULATIONS FOR ASME CODE SECTION VIII, DIVISION I, 2017 EDITION
PRESSURE VESSEL CALCULATIONS
WORKBOOK VERSION: 09222018b
Shell Page 1 of 1
PIPE USED AS SHELL CYLINDERS = 1 10/24/2018
JOB NO. 0
Dimensions: 0
0.000 Do [in] - outside diameter

t
0.000 Di [in] - inside diameter 0.000

Do
0.000 t [in] - nominal wall thickness
Long Seam
0.000 L [in] -length
0.000 Corr [in] - corrosion allowance
Material and Conditions: Length
INHERENT Material 0.000
#N/A S [psi] - allowable stress
0.85 El - long seam efficiency (circ stress) 85%
0.70 Ec - circ seam efficiency (long stress) 70%
12.5% UTP [%] - undertolerance allowance
0.0 P [psi] - interior pressure
Calculated Properties:
Volume [cuft] = ((Di/2)^2)*pi()*L/1728 ((0/2)^2)*PI()*0/1728 = 0.00
Weight [lb] = (Di+t)*pi()*L*t*40.84/144 (0+0)*PI()*0*0*40.84/144 = 0.00
Variables: Pipe used for shell
UT [in] = t*UTP 0*0.1 = 0.000
nt [in] = t-Corr-UT 0-0-0 = 0.000
Ri [in] = Di/2+UT+Corr 0/2+0+0= 0.000
Ro [in] = (Di/2)+t 0/2+0= 0.000
Required Thickness: UG-27(c)(1,2)
ta [in] = P*Ri/(S*El-0.6*P) ~~ long seam #N/A #N/A
tb [in] = P*Ri/(2*S*Ec+0.4*P) ~~ circ seam #N/A #N/A
Treq [in] = MAX(ta,tb) ~~ required minimum thickness #N/A #N/A
CheckTreq = Treq <= nt #N/A #N/A
Required Thickness: Appendix 1-1(a)(1), UG-16(b)
ta [in] = P*Ro/(S*El+0.4*P) ~~ long seam #N/A #N/A
CheckTreq = Treq <= nt #N/A #N/A
Check UG-16(b) = nt >= 0.0625+Corr 0 >= 0.0625 = ERROR
Maximum Pressure: UG-27(c)(1,2)
Pint1 [psi] = (S*El*nt)/(Ri+0.6*nt) #N/A #N/A
Pint2 [psi] = (2*S*Ec*nt)/(Ri-0.4*nt) #N/A #N/A
PMax [psi] = Min(Pint1,Pint2) ~~ maximum allowed design pressure #N/A #N/A
CheckP = PMax >= P #N/A #N/A
Stress Classification:
NOTE: Both validity checks need to be "Acceptable" in order to use this sheet

ckValidity1 = Treq < 0.5*(Do/2) #N/A #N/A


ckValidity2 = P< 0.385*S*El #N/A #N/A

Minimum design temperature check: Impact testing exempt to -20F per UG20(f)
UCS-66 CURVE 'B' RATING [F]: #N/A / 'D' [F]: #N/A

Allowable stress for vertical vessel: N/A


(Tall thin wall vessel without stiffeners) N/A

Treq provides a worst case required thickness for nozzle analysis for a nozzle located on the long seam or circ seam
This sheet calculates vessel walls per ASME Section VIII Division 1 only.
All UG-16(b) minimum thickness requirements have not been taken into consideration here.
Use "SHELL EXTERNAL" sheet to check for allowable exterior pressure loads.
CALCULATIONS FOR ASME CODE SECTION VIII, DIVISION I, 2017 EDITION
PRESSURE VESSEL CALCULATIONS
WORKBOOK VERSION: 09222018b
Shell #2 (Boot on Shell) Page 1 of 1
10/24/2018
JOB NO. 0
Dimensions: 0.000
0.000 Do [in] - outside diameter 0.000 Do
0.000 Di [in] - inside diameter
0 t [in] - nominal wall thickness t= 0.000
0.000 L [in] -length t
0.000 Corr [in] - corrosion allowance
Material and Conditions: #N/A

Length
INHERENT Material 0.000
#N/A S [psi] - allowable stress

Long Seam
0 El - long seam efficiency (circ stress) 85%
0.7 Ec - circ seam efficiency (long stress) 70%
0.0% UTP [%] - undertolerance allowance 0.0%
0.0 P [psi] - interior pressure 0 CYLINDERS = 1
Calculated Properties:
Volume [cuft] = ((Di/2)^2)*pi()*L/1728 ((0/2)^2)*PI()*0/1728 = 0.00
Weight [lb] = (Di+t)*pi()*L*t*40.84/144 (0+0)*PI()*0*0*40.84/144 = 0.00
Variables: Rolled Plate used for shell
UT [in] = t*UTP 0*0 = 0.000 0.000
nt [in] = t-Corr-UT 0-0-0 = 0.000
Ri [in] = Di/2+UT+Corr 0/2+0+0= 0.000
Ro [in] = (Di/2)+t 0/2+0= 0.000
Required Thickness: UG-27(c)(1,2)
ta [in] = P*Ri/(S*El-0.6*P) ~~ long seam #N/A #N/A
tb [in] = P*Ri/(2*S*Ec+0.4*P) ~~ circ seam #N/A #N/A
Treq [in] = MAX(ta,tb) ~~ required minimum thickness #N/A #N/A
CheckTreq = Treq <= nt #N/A #N/A
Required Thickness: Appendix 1-1(a)(1), UG-16(b)
ta [in] = P*Ro/(S*El+0.4*P) ~~ long seam #N/A #N/A #N/A
CheckTreq = Treq <= nt #N/A #N/A
Check UG-16(b) = nt >= 0.0625+Corr 0 >= 0.0625 = ERROR
Maximum Pressure: UG-27(c)(1,2)
Pint1 [psi] = (S*El*nt)/(Ri+0.6*nt) #N/A #N/A
Pint2 [psi] = (2*S*Ec*nt)/(Ri-0.4*nt) #N/A #N/A
PMax [psi] = Min(Pint1,Pint2) ~~ maximum allowed design pressure #N/A #N/A
CheckP = PMax >= P #N/A #N/A
Stress Classification:
NOTE: Both validity checks need to be "Acceptable" in order to use this sheet

ckValidity1 = Treq < 0.5*(Do/2) #N/A #N/A


ckValidity2 = P< 0.385*S*El #N/A #N/A
Minimum design temperature check: Impact testing exempt to -20F per UG20(f)
UCS-66 CURVE 'B' RATING [F]: #N/A / 'D' [F]: #N/A

This sheet calculates vessel walls per ASME Section VIII Division 1 only.
All UG-16(b) minimum thickness requirements have not been taken into consideration here.
Use "SHELL EXTERNAL" sheet to check for allowable exterior pressure loads.
YOUR COMPANY NAME
CALCULATIONS FOR ASME CODE SECTION VIII, DIVISION I, 2017 EDITION
PRESSURE VESSEL CALCULATIONS
WORKBOOK VERSION: 09222018b
Page 1 of 1
HEAD A ELLIPTICAL 2:1 RATIO Page 10/24/2018
(TOP OR END)
JOB NO. 0
Dimensions:
0.000 Do [in] - outside diameter of head Formed thickness = -0.063 in
0.000 Di [in] - inside diameter of head
0.000 tb [in] - thickness before forming
0.000 tf [in] - thickness after forming (note 1)
0.000 Corr [in] - corrosion allowance
0.000 Skirt [in] - straight skirt length
Material and Conditions:
SA-36 Material
16,600 S [psi] - allowable stress
0.0% UTP [%] - undertolerance allowance
0.85 E - head/shell joint efficiency
0.0 P [psi] - interior pressure
Calculated Properties:
note 1: Suggested thickness after forming Approx. head weight based on steel, lbs = 0.00
-0.0625 in Approx. head volume including skirt, cuft = 0.00
Variables:
ut [in] = tf*UTP ~~ undertorlerance allowance -0.063*0 = 0.000 -0.063
nt [in] = tf-(Corr+ut) ~~ thickness with corrosion allowance removed -0.063-0+0 = -0.063
D [in] = Do-2*nt ~ ID with corrosion allowance removed 0+2*0-(-0.063*2) = 0.125
h [in] = D/4 ~~ inside crown height 0.125/4 = 0.031
ho [in] = h+nt 0.031+-0.063 = -0.031
D/2h = D/(2*h) 0.125/(2*0.031) = 0.000
Do/2ho = Do/(2*ho) 0+(0*2)/(2*-0.031) = 0.000
K = #N/A Interpolated value from table 1-4.1 1 = 0.000
Kone = #N/A Interpolated value from table UG-37 0.9 = 0.000
Kzero = #N/A Interpolated value from table UG-33.1 0.889 = 0.000
Ro [in]= Kzero*Do 0*0 = 0.000
Required Thickness: App. 1-4(c), UG-37(a)(1)
App1-4(f) = tf/(Kone*D) -0.063/(0*0.125) = 0.0000
App. 1-4(f) Calculation Not Required
Treq [in] = (P*D*K)/(2*S*E-0.2*P)+Corr + ut~~ required minimum thickness
(0*0.125*0)/(2*16600*0.85-0.2*0)+0= 0.000
CheckTreq = Treq<=tf 0<=-0.063 = ERROR
Check UG-16(b) = nt >= 0.0625+Corr -0.063 >= 0.0625 = ERROR

Maximum Pressure: App. 1-4(c), UG-37(a)(1)


Pmax [psi] = (2*S*E*nt)/(K*D+0.2*nt) ~~ maximum allowed design pressure
(2*16600*0.85*-0.063)/(0*0.125+0.2*-0.063) = 0.0
CheckPMax = Pmax >= P 0 >= 0 = Acceptable
Minimum design temperature check: Impact testing exempt to -20F per UG20(f)
UCS-66 CURVE 'B' RATING [F]: #N/A / 'D' [F]: #N/A
All UG-16(b) minimum thickness requirements have not been taken into consideration here.
Nozzles may be subject to a smaller required thickness depending on location in the head.
Heads may be subject to stress relief if large elongation occurs - UCS-79(d), UNF-79(d), UHA-44(d)
This sheet cannot be used to check for allowable exterior pressure loads.
YOUR COMPANY NAME
CALCULATIONS FOR ASME CODE SECTION VIII, DIVISION I, 2017 EDITION
PRESSURE VESSEL CALCULATIONS
WORKBOOK VERSION: 09222018b
Page 1 of 1
HEAD B ELLIPTICAL Page 10/24/2018
(BOTTOM OR END)
JOB NO. 0
Dimensions:
0.000 Do [in] - outside diameter of head Formed thickness = -0.063 in
0.000 Di [in] - inside diameter of head
0.000 tb [in] - thickness before forming
0.000 tf [in] - thickness after forming (note 1)
0.000 Corr [in] - corrosion allowance
0.000 Skirt [in] - straight skirt length
Material and Conditions:
SA-36 Material
16,600 S [psi] - allowable stress
0.0% UTP [%] - undertolerance allowance
0.85 E - head/shell joint efficiency
0.0 P [psi] - interior pressure
Calculated Properties:
note 1: Suggested thickness after forming Approx. head weight based on steel, lbs = 0.00
-0.0625 in Approx. head volume including skirt, cuft = 0.00
Variables:
ut [in] = tf*UTP ~~ undertorlerance allowance -0.063*0 = 0.000 -0.063
nt [in] = tf-(Corr+ut) ~~ thickness with corrosion allowance removed -0.063-0+0 = -0.063
D [in] = Do-2*nt ~ ID with corrosion allowance removed 0+2*0-(-0.063*2) = 0.125
h [in] = D/4 ~~ inside crown height 0.125/4 = 0.031
ho [in] = h+nt 0.031+-0.063 = -0.031
D/2h = D/(2*h) 0.125/(2*0.031) = 0.000
Do/2ho = Do/(2*ho) 0+(0*2)/(2*-0.031) = 0.000
K = #N/A Interpolated value from table 1-4.1 1 = 0.000
Kone = #N/A Interpolated value from table UG-37 0.9 = 0.000
Kzero = #N/A Interpolated value from table UG-33.1 0.889 = 0.000
Ro [in]= Kzero*Do 0*0 = 0.000
Required Thickness: App. 1-4(c), UG-37(a)(1)
App1-4(f) = tf/(Kone*D) -0.063/(0*0.125) = 0.0000
App. 1-4(f) Calculation Not Required
Treq [in] = (P*D*K)/(2*S*E-0.2*P)+Corr ~~ required minimum thickness
(0*0.125*0)/(2*16600*0.85-0.2*0)+0= 0.000
CheckTreq = Treq<=tf 0<=-0.063 = ERROR
Check UG-16(b) = nt >= 0.0625+Corr -0.063 >= 0.0625 = ERROR

Maximum Pressure: App. 1-4(c), UG-37(a)(1)


Pmax [psi] = (2*S*E*nt)/(K*D+0.2*nt) ~~ maximum allowed design pressure
(2*16600*0.85*-0.063)/(0*0.125+0.2*-0.063) = 0.0
CheckPMax = Pmax >= P 0 >= 0 = Acceptable
Minimum design temperature check: Impact testing exempt to -20F per UG20(f)
UCS-66 CURVE 'B' RATING [F]: #N/A / 'D' [F]: #N/A
All UG-16(b) minimum thickness requirements have not been taken into consideration here.
Nozzles may be subject to a smaller required thickness depending on location in the head.
Heads may be subject to stress relief if large elongation occurs - UCS-79(d), UNF-79(d), UHA-44(d)
This sheet cannot be used to check for allowable exterior pressure loads.
YOUR COMPANY NAME
CALCULATIONS FOR ASME CODE SECTION VIII, DIVISION I, 2017 EDITION
PRESSURE VESSEL CALCULATIONS
WORKBOOK VERSION: 09222018b
Page 1 of 1
HEAD A NOT USED (TOP or END) 10/24/2018

JOB NO. 0
Dimensions:
0.000 Di [in] - inside diameter of head
0.000 Do [in] - outside diameter of head
0.000 L [in] - inside crown radius (note 1)
0.000 IKR [in] - inside knuckle radius (note 2)
0.000 tb [in] - thickness before forming
0.000 tf [in] - thickness after forming
0.000 Corr [in] - corrosion allowance
0.000 Skirt [in] - straight skirt length
Material and Conditions:
SA-36 Material
16,600 S [psi] - allowable stress
0.85 E - head longitudinal efficiency
0.0 P [psi] - interior pressure
Calculated Properties:
note 1:Suggested radius L per UG-32(j) 0.00 Approx. head weight based on steel, lbs = 0.00
note 2:Suggested radius IKR per UG-32(j) 0.000 Approx. head volume including skirt, cuft = 0.00
note 3:Suggested thickness after forming -0.0320
Variables:
t [in] = tf-Corr ~~ thickness with corrosion allowance removed 0-0 = 0.000
D [in] = Di+2*Corr ~~ ID with corrosion allowance removed 0+2*0 = 0.000
L/r = L/IKR 0/0 = 0.000
M= 0.25*(3+sqrt(L/IKR)) 0.25*(3+SQRT(0/0)) = 0.000
Ro [in] = L+tb 0+0 = 0.000
Required Thickness: App. 1-4(a), App. 1-4(d)
App1-4(f) = tf/L 0/0 = #DIV/0!
App1-4(f)Calc = if(AND(0.0005=<App1-4(f),App1-4(f)<0.002),"Calculation Required","Calculation not required")
#DIV/0!
Treq [in] = (P*L*M)/(2*S*E-0.2*P)+Corr ~~ required minimum thickness
(0*0*0)/(2*16600*0.85-0.2*0)+0 = 0.000
CheckTreq = Treq<=tf 0<=0 = Acceptable
Maximum Pressure: App. 1-4(a), App. 1-4(d)
Pmax [psi] = (2*S*E*t)/(L*M+0.2*t) ~~ maximum allowed design pressure
(2*16600*0.85*0)/(0*0+0.2*0) = 0.0
CheckPMax = Pmax >= P 0 >= 0 = Acceptable
Minimum design temperature check: Impact testing exempt to -20F per UG20(f)
UCS-66 CURVE 'B' RATING [F]: #N/A / 'D' [F]: #N/A

App. 1-4(f) calculation is not included on this sheet


Nozzles may be subject to a smaller required thickness depending on location in the head.
Heads may be subject to stress relief if large elongation occurs - UCS-79(d), UNF-79(d), UG-37(a)(1)
All UG-16(b) minimum thickness requirements have not been taken into consideration here.
This sheet cannot be used to check for allowable exterior pressure loads.

Note 1: If you change the Dish Radius, the sheet will no longer give the default for F&D.
Note 2: The default value for the Knuckle Radius is 0.06 times the head O.D.
YOUR COMPANY NAME
CALCULATIONS FOR ASME CODE SECTION VIII, DIVISION I, 2017 EDITION
PRESSURE VESSEL CALCULATIONS
WORKBOOK VERSION: 09222018b
Page 1 of 1
HEAD B NOT USED (BOTTOM or END) Page 10/24/2018

JOB NO. 0
Dimensions:
0.000 Di [in] - inside diameter of head
0.000 Do [in] - outside diameter of head
0.000 L [in] - inside crown radius (note 1)
0.000 IKR [in] - inside knuckle radius (note 2)
0.000 tb [in] - thickness before forming
0.000 tf [in] - thickness after forming
0.000 Corr [in] - corrosion allowance
0.000 Skirt [in] - straight skirt length
Material and Conditions:
SA-36 Material
16,600 S [psi] - allowable stress
0.85 E - head longitudinal efficiency
0.0 P [psi] - interior pressure
Calculated Properties:
note 1:Suggested radius L per UG-32(j) 0.00 Approx. head weight based on steel, lbs = 0.00
note 2:Suggested radius IKR per UG-32(j) 0.000 Approx. head volume including skirt, cuft = 0.00
note 3:Suggested thickness after forming -0.0320
Variables:
t [in] = tf-Corr ~~ thickness with corrosion allowance removed 0-0 = 0.000
D [in] = Di+2*Corr ~~ ID with corrosion allowance removed 0+2*0 = 0.000
L/r = L/IKR 0/0 = 0.000
M= 0.25*(3+sqrt(L/IKR)) 0.25*(3+SQRT(0/0)) = 0.000
Ro [in] = L+tb 0+0 = 0.000
Required Thickness: App. 1-4(a), App. 1-4(d)
App1-4(f) = tf/L 0/0 = #DIV/0!
App1-4(f)Calc = if(AND(0.0005=<App1-4(f),App1-4(f)<0.002),"Calculation Required","Calculation not required")
#DIV/0!
Treq [in] = (P*L*M)/(2*S*E-0.2*P)+Corr ~~ required minimum thickness
(0*0*0)/(2*16600*0.85-0.2*0)+0 = 0.000
CheckTreq = Treq<=tf 0<=0 = Acceptable
Maximum Pressure: App. 1-4(a), App. 1-4(d)
Pmax [psi] = (2*S*E*t)/(L*M+0.2*t) ~~ maximum allowed design pressure
(2*16600*0.85*0)/(0*0+0.2*0) = 0.0
CheckPMax = Pmax >= P 0 >= 0 = Acceptable
Minimum design temperature check: Impact testing exempt to -20F per UG20(f)
UCS-66 CURVE 'B' RATING [F]: #N/A / 'D' [F]: #N/A

App. 1-4(f) calculation is not included on this sheet


Nozzles may be subject to a smaller required thickness depending on location in the head.
Heads may be subject to stress relief if large elongation occurs - UCS-79(d), UNF-79(d), UG-37(a)(1)
All UG-16(b) minimum thickness requirements have not been taken into consideration here.
This sheet cannot be used to check for allowable exterior pressure loads.

Note 1: If you change the Dish Radius, the sheet will no longer give the default for F&D.
Note 2: The default value for the Knuckle Radius is 0.06 times the head O.D.
YOUR COMPANY NAME
CALCULATIONS FOR ASME CODE SECTION VIII, DIVISION I, 2017 EDITION
PRESSURE VESSEL CALCULATIONS
WORKBOOK VERSION: 09222018b

Shell Nozzle and Repad (Not Required) 10/24/2018 Page 1 of 2 #VALUE!


NOZZLE 1 -- NOT USED 0 INCH/PSI OTHER
JOB NO: 0 NOZZLE ID. QUANTITY= 0
Shell Inputs: FLANGE/COUPLING RATING 0 PSI
INHERENT Material
#N/A Sv [psi] - allowable stress
0.85 E1 - efficiency of shell at nozzle
0.000 Ds [in] - inside diameter of shell
0.000 nt [in] - nominal shell wall thickness
#N/A Treq [in] - required shell wall thickness
0.000 sca [in] - shell corrosion allowance
0.063 tUG16(b) [in] - minimum thickness per UG-16 b
Nozzle Inputs:
INHERENT Material
0 Sn [psi] - allowable stress
1.00 E - nozzle efficiency
0.000 Do [in] - outside diameter of nozzle
0.0000 Nwall [in] - nominal wall thickness of nozzle
0.000 Lp [in] - exterior projection of nozzle
0.000 Ip [in] - interior projection of nozzle
0.000 nca [in] - nozzle corrosion allowance
0.0% UTP [%] - undertolerance allowance
0.0 Pn [psi] - interior pressure

Reinforcement:
INHERENT Material
#N/A Sp [psi] - allowable stress of repad
0.0000 te [in] - repad thickness 0.000
0.000 Dp [in] - outside diameter
0.000 Leg41 [in] - fillet size
0.000 Leg42 [in] - fillet size
0.000 Leg43 [in] - fillet size
0.000 LegG [in] - depth of groove
Variables:
UT [in] = Nwall*UTP 0*0 = 0.000
Rn [in] = Do/2 - (Nwall-nca) + UT 0/2 - (0-0) + 0 = 0.000
ti [in] = Nwall-2*nca 0-2*0 = 0.000
h [in] = MIN(Ip-sca,2.5*nt,2.5*ti) MIN(0-0,2.5*0,2.5*0) = 0.000
tn [in] = Nwall-nca 0-0 = 0.000
d [in] = Do-2*tn 0-2*0 = 0.000
fr1 = MIN(Sn/Sv,1) #N/A #N/A
fr2 = MIN(Sn/Sv,1) #N/A #N/A
fr3 = MIN(Sn/Sv,Sp/Sv,1) #N/A #N/A
fr4 = MIN(Sp/Sv,1) #N/A #N/A
Required Thickness: UG-27(c)(1,2)
TreqN [in] = (Pn*Rn)/(Sn*E - 0.6*Pn)+nca ~~ required minimum thickness
(0*0)/(0*1 - 0.6*0)+0 = #DIV/0!
trnR [in] = (Pn*Rn)/(Sn*1 - 0.6*Pn) (0*0)/(0*1 - 0.6*0) = #DIV/0!
CheckTreqN = TreqN <= Nwall #DIV/0! #DIV/0!
UG-45:
Tstd [in] = thickness standard wall pipe VLOOKUP(0,PIpeWall,2) = #N/A
Nact [in] = Nwall * (1-UTP) 0 * (1-0) = 0.000
UG45 [in] = Max(UG45a, UG45b) ~~ required thickness per UG-45 #DIV/0! #DIV/0!
UG45a [in] = trnR + nca #DIV/0! #DIV/0!

Shell Nozzle 1 Page 2 of 2

UG45b [in] = Min(UG45b3,UG45b4) #N/A #N/A


UG45b1 [in] = Max(Treq+sca,tUG16(b) + sca) #N/A #N/A
UG45b2 [in] = 0 0= 0.000
UG45b3 [in] = Max(UG45b1,UG45b2) #N/A #N/A
UG45b4 [in] = Tstd*0.875 + nca #N/A #N/A
CheckUG45 = UG45 <= Nact #DIV/0!#DIV/0!
#DIV/0!
Minimum thickness per UG-45 [in] = #N/A #N/A

Area Replacement:
Ar [in^2] = 1*d*Treq*1+2*tn*Treq*1*(1-fr1) ~~ required Area
#N/A #N/A
A1 [in^2] = max(d, 2*(nt+tn)) * (E1*nt-1*Treq)-2*tn*(E1*nt-1*Treq)*(1-fr1)
#N/A #N/A
A2 [in^2] = min((tn-trnR)*fr2*min(5*nt,2*Lp),(tn-trnR)*(Min(2.5*tn+te,2*Lp)*fr2*2))
#DIV/0! #DIV/0!
A3 [in^2] = Min(5*nt*ti*fr2,5*ti*ti*fr2,2*h*ti*fr2)
#N/A #N/A
A5 [in^2] = (Dp-d-2*tn)*te*fr4 N/A = 0.000
A41 [in^2] = Leg41^2*fr3 #N/A #N/A
A42 [in^2] = Leg42^2*fr4 #N/A #N/A
A43 [in^2] = (Leg43-nca)^2*fr2 #N/A #N/A
Aa [in^2] = A1+A2+A3+A5+A41+A42+A43 ~~ actual area
#N/A #N/A
CheckA = Aa >= Ar ~~ check area replacement #N/A #N/A

Nozzle Weld Strength: per UW-16(a), (b)


Weld 41 tmin [in] = smaller of 0.75, nt, or Nwall 0.000 0.000 0.000 = 0.0000
Weld 41 Leg [in] = smaller of 0.25 or (tmin * 0.7) / 0.7 0 = 0.0000
0 >= 0 = ERROR
Weld 42 tmin [in] = (smaller of 0.5nt or te) 0.000 = 0.0000
Weld 42 Leg [in] = (smaller of 0.25 or (temin * 0.7) / 0.7) 0 = 0.0000
0 0 >= 0 = N/A
Weld 43 Leg [in] = (smaller of 0.25 or (tmin * 0.7) / 0.7) + sca = 0.0000
0 0 >= 0 = N/A

Nozzle Weld Strength: per UW-16(i) (using Weld 41 only)

Weld 41 + Weld 43 tmin [in] = smaller of 1.25 * nt, or Nwall (0.25" min)
0.000 0 * 1.25 = 0.0000
(using Weld 41 only) 0+0 >= 0 = Acceptable
0 >= 0.25 = ERROR

Minimum design temperature check: Impact testing exempt to -20F per UG20(f)
UCS-66 CURVE 'B' RATING [F]: N/A
0 #N/A #N/A #N/A #N/A #N/A
Calculated nozzle weight (LBS): 0.00 #N/A #N/A #N/A #N/A #N/A
Nozzle & Flange overide weight (LBS): 0.00
Note: Attached piping to be externally supported. Calculations are limited to materials listed in this sheet.
YOUR COMPANY NAME
CALCULATIONS FOR ASME CODE SECTION VIII, DIVISION I, 2017 EDITION
PRESSURE VESSEL CALCULATIONS
WORKBOOK VERSION: 09222018b

Shell Nozzle and Repad (Not Required) 10/24/2018 Page 1 of 2


NOZZLE 2 -- NOT USED 0 INCH/PSI OTHER
JOB NO: 0 NOZZLE ID. QUANTITY= 0
Shell Inputs: FLANGE/COUPLING RATING 0 PSI
INHERENT Material
#N/A Sv [psi] - allowable stress
0.85 E1 - efficiency of shell at nozzle
0.000 Ds [in] - inside diameter of shell
0.000 nt [in] - nominal shell wall thickness
#N/A Treq [in] - required shell wall thickness
0.000 sca [in] - shell corrosion allowance
0.063 tUG16(b) [in] - minimum thickness per UG-16 b
Nozzle Inputs:
INHERENT Material
0 Sn [psi] - allowable stress
1.00 E - nozzle efficiency
0.000 Do [in] - outside diameter of nozzle
0.0000 Nwall [in] - nominal wall thickness of nozzle
0.0000 CLn [in] - nozzle offset from vessel centerline
0.000 Lp [in] - exterior projection of nozzle
0.000 Ip [in] - interior projection of nozzle
0.000 nca [in] - nozzle corrosion allowance
0.0% UTP [%] - undertolerance allowance
0.0 Pn [psi] - interior pressure

Reinforcement:
INHERENT Material
#N/A Sp [psi] - allowable stress of repad
0.0000 te [in] - repad thickness 0.000
0.000 Dp [in] - outside diameter
0.000 Leg41 [in] - fillet size
0.000 Leg42 [in] - fillet size
0.000 Leg43 [in] - fillet size
0.000 LegG [in] - depth of groove
Variables:
UT [in] = Nwall*UTP 0*0 = 0.000
Rn [in] = Do/2 - (Nwall-nca) + UT 0/2 - (0-0) + 0 = 0.000
ti [in] = Nwall-2*nca 0-2*0 = 0.000
h [in] = MIN(Ip-sca,2.5*nt,2.5*ti) MIN(0-0,2.5*0,2.5*0) = 0.000
tn [in] = Nwall-nca 0-0 = 0.000
d [in] = ((Tangent Do+Do)/2)-(2*tn) (0+0)/2)-(2*0) = 0.000 REQUIRED
fr1 = MIN(Sn/Sv,1) #N/A #N/A
fr2 = MIN(Sn/Sv,1) #N/A #N/A
fr3 = MIN(Sn/Sv,Sp/Sv,1) #N/A #N/A
fr4 = MIN(Sp/Sv,1) #N/A #N/A
Required Thickness: UG-27(c)(1,2)
TreqN [in] = (Pn*Rn)/(Sn*E - 0.6*Pn)+nca ~~ required minimum thickness
(0*0)/(0*1 - 0.6*0)+0 = #DIV/0!
trnR [in] = (Pn*Rn)/(Sn*1 - 0.6*Pn) (0*0)/(0*1 - 0.6*0) = #DIV/0!
CheckTreqN = TreqN <= Nwall #DIV/0! #DIV/0!
UG-45:
Tstd [in] = thickness standard wall pipe VLOOKUP(0,PIpeWall,2) = #N/A
Nact [in] = Nwall * (1-UTP) 0 * (1-0) = 0.000
UG45 [in] = Max(UG45a, UG45b) ~~ required thickness per UG-45 #DIV/0! #DIV/0!
UG45a [in] = trnR + nca #DIV/0! #DIV/0!

Shell Nozzle 2 Page 2 of 2


UG45b [in] = Min(UG45b3,UG45b4) #N/A #N/A
UG45b1 [in] = Max(Treq+sca,tUG16(b) + sca) #N/A #N/A
UG45b2 [in] = 0 0= 0.000
UG45b3 [in] = Max(UG45b1,UG45b2) #N/A #N/A
UG45b4 [in] = Tstd*0.875 + nca #N/A #N/A
CheckUG45 = UG45 <= Nact #DIV/0!#DIV/0!
#DIV/0!
Minimum thickness per UG-45 [in] = #N/A #N/A

Area Replacement:
Ar [in^2] = 1*d*Treq*1+2*tn*Treq*1*(1-fr1) ~~ required Area
#N/A #N/A
A1 [in^2] = max(d, 2*(nt+tn)) * (E1*nt-1*Treq)-2*tn*(E1*nt-1*Treq)*(1-fr1)
#N/A #N/A
A2 [in^2] = min((tn-trnR)*fr2*min(5*nt,2*Lp),(tn-trnR)*(Min(2.5*tn+te,2*Lp)*fr2*2))
#DIV/0! #DIV/0!
A3 [in^2] = Min(5*nt*ti*fr2,5*ti*ti*fr2,2*h*ti*fr2)
#N/A #N/A
A5 [in^2] = (Dp-d-2*tn)*te*fr4 N/A = 0.000
A41 [in^2] = Leg41^2*fr3 #N/A #N/A
A42 [in^2] = Leg42^2*fr4 #N/A #N/A
A43 [in^2] = (Leg43-nca)^2*fr2 #N/A #N/A
Aa [in^2] = A1+A2+A3+A5+A41+A42+A43 ~~ actual area
#N/A #N/A
CheckA = Aa >= Ar ~~ check area replacement #N/A #N/A

Nozzle Weld Strength: per UW-16(a), (b)


Weld 41 tmin [in] = smaller of 0.75, nt, or Nwall 0.000 0.000 0.000 = 0.0000
Weld 41 Leg [in] = smaller of 0.25 or (tmin * 0.7) / 0.7 0 = 0.0000
0 >= 0 = ERROR
Weld 42 tmin [in] = (smaller of 0.5nt or te) 0.000 = 0.0000
Weld 42 Leg [in] = (smaller of 0.25 or (temin * 0.7) / 0.7) 0 = 0.0000
0 0 >= 0 = N/A
Weld 43 Leg [in] = (smaller of 0.25 or (tmin * 0.7) / 0.7) + sca = 0.0000
0 0 >= 0 = N/A

Minimum design temperature check: CURVE "D"


UCS-66 CURVE 'B' RATING [F]: #N/A

Shell tangent nozzle: Large nozzle diameter 0.000 (in)

Nozzle Weld Strength: per UW-16(i) (using Weld 41 only)


Weld 41 + Weld 43 tmin [in] = smaller of 1.25 * nt, or Nwall (0.25" min) 0 * 1.25 = 0.0000
0.000 0+0 >= 0 = Acceptable
(using Weld 41 only) 0 >= 0.25 = ERROR
0 #N/A #N/A #N/A #N/A #N/A
Calculated nozzle weight (LBS): 0.00 #N/A #N/A #N/A #N/A #N/A
Nozzle & Flange overide weight (LBS): 0.00
Note: Attached piping to be externally supported. Calculations are limited to materials listed in this sheet.
YOUR COMPANY NAME
CALCULATIONS FOR ASME CODE SECTION VIII, DIVISION I, 2017 EDITION
PRESSURE VESSEL CALCULATIONS
WORKBOOK VERSION: 09222018b

Shell Nozzle and Repad (Not Required) 10/24/2018 Page 1 of 2


NOZZLE 3 -- NOT USED 0 INCH/PSI OTHER
JOB NO: 0 NOZZLE ID. QUANTITY= 0
Shell Inputs: FLANGE/COUPLING RATING 0 PSI
INHERENT Material
#N/A Sv [psi] - allowable stress
0.85 E1 - efficiency of shell at nozzle
0.000 Ds [in] - inside diameter of shell
0.000 nt [in] - nominal shell wall thickness
#N/A Treq [in] - required shell wall thickness
0.000 sca [in] - shell corrosion allowance
0.063 tUG16(b) [in] - minimum thickness per UG-16 b
Nozzle Inputs:
INHERENT Material
0 Sn [psi] - allowable stress
1.00 E - nozzle efficiency
0.000 Do [in] - outside diameter of nozzle
0.0000 Nwall [in] - nominal wall thickness of nozzle
0.0000 CLn [in] - nozzle offset from vessel centerline
0.000 Lp [in] - exterior projection of nozzle
0.000 Ip [in] - interior projection of nozzle
0.000 nca [in] - nozzle corrosion allowance
0.0% UTP [%] - undertolerance allowance
0.0 Pn [psi] - interior pressure

Reinforcement:
INHERENT Material
#N/A Sp [psi] - allowable stress of repad
0.0000 te [in] - repad thickness 0.0000
0.000 Dp [in] - outside diameter
0.000 Leg41 [in] - fillet size
0.000 Leg42 [in] - fillet size
0.000 Leg43 [in] - fillet size
0.000 LegG [in] - depth of groove
Variables:
UT [in] = Nwall*UTP 0*0 = 0.000
Rn [in] = Do/2 - (Nwall-nca) + UT 0/2 - (0-0) + 0 = 0.000
ti [in] = Nwall-2*nca 0-2*0 = 0.000
h [in] = MIN(Ip-sca,2.5*nt,2.5*ti) MIN(0-0,2.5*0,2.5*0) = 0.000
tn [in] = Nwall-nca 0-0 = 0.000
d [in] = ((Tangent Do+Do)/2)-(2*tn) (0+0)/2)-(2*0) = 0.000 REQUIRED
fr1 = MIN(Sn/Sv,1) #N/A #N/A
fr2 = MIN(Sn/Sv,1) #N/A #N/A
fr3 = MIN(Sn/Sv,Sp/Sv,1) #N/A #N/A
fr4 = MIN(Sp/Sv,1) #N/A #N/A
Required Thickness: UG-27(c)(1,2)
TreqN [in] = (Pn*Rn)/(Sn*E - 0.6*Pn)+nca ~~ required minimum thickness
(0*0)/(0*1 - 0.6*0)+0 = #DIV/0!
trnR [in] = (Pn*Rn)/(Sn*1 - 0.6*Pn) (0*0)/(0*1 - 0.6*0) = #DIV/0!
CheckTreqN = TreqN <= Nwall #DIV/0! #DIV/0!
UG-45:
Tstd [in] = thickness standard wall pipe VLOOKUP(0,PIpeWall,2) = #N/A
Nact [in] = Nwall * (1-UTP) 0 * (1-0) = 0.000
UG45 [in] = Max(UG45a, UG45b) ~~ required thickness per UG-45 #DIV/0! #DIV/0!
UG45a [in] = trnR + nca #DIV/0! #DIV/0!
Shell Nozzle 3 Page 2 of 2

UG45b [in] = Min(UG45b3,UG45b4) #N/A #N/A


UG45b1 [in] = Max(Treq+sca,tUG16(b) + sca) #N/A #N/A
UG45b2 [in] = 0 0= 0.000
UG45b3 [in] = Max(UG45b1,UG45b2) #N/A #N/A
UG45b4 [in] = Tstd*0.875 + nca #N/A #N/A
CheckUG45 = UG45 <= Nact #DIV/0!#DIV/0!
#DIV/0!
Minimum thickness per UG-45 [in] = #N/A #N/A

Area Replacement:
Ar [in^2] = 1*d*Treq*1+2*tn*Treq*1*(1-fr1) ~~ required Area
#N/A #N/A
A1 [in^2] = max(d, 2*(nt+tn)) * (E1*nt-1*Treq)-2*tn*(E1*nt-1*Treq)*(1-fr1)
#N/A #N/A
A2 [in^2] = min((tn-trnR)*fr2*min(5*nt,2*Lp),(tn-trnR)*(Min(2.5*tn+te,2*Lp)*fr2*2))
#DIV/0! #DIV/0!
A3 [in^2] = Min(5*nt*ti*fr2,5*ti*ti*fr2,2*h*ti*fr2)
#N/A #N/A
A5 [in^2] = (Dp-d-2*tn)*te*fr4 N/A = 0.000
A41 [in^2] = Leg41^2*fr3 #N/A #N/A
A42 [in^2] = Leg42^2*fr4 #N/A #N/A
A43 [in^2] = (Leg43-nca)^2*fr2 #N/A #N/A
Aa [in^2] = A1+A2+A3+A5+A41+A42+A43 ~~ actual area
#N/A #N/A
CheckA = Aa >= Ar ~~ check area replacement #N/A #N/A

Nozzle Weld Strength: per UW-16(a), (b)


Weld 41 tmin [in] = smaller of 0.75, nt, or Nwall 0.000 0.000 0.000 = 0.0000
Weld 41 Leg [in] = smaller of 0.25 or (tmin * 0.7) / 0.7 0 = 0.0000
0 >= 0 = ERROR
Weld 42 tmin [in] = (smaller of 0.5nt or te) 0.000 = 0.0000
Weld 42 Leg [in] = (smaller of 0.25 or (temin * 0.7) / 0.7) 0 = 0.0000
0 0 >= 0 = N/A
Weld 43 Leg [in] = (smaller of 0.25 or (tmin * 0.7) / 0.7) + sca = 0.0000
0 0 >= 0 = N/A
Minimum design temperature check: Impact testing exempt to -20F per UG20(f)
UCS-66 CURVE 'B' RATING [F]: #N/A

Shell tangent nozzle: Large nozzle diameter 0.000 (in)

Nozzle Weld Strength: per UW-16(i) (using Weld 41 only)


Weld 41 + Weld 43 tmin [in] = smaller of 1.25 * nt, or Nwall (0.25" min) 0 * 1.25 = 0.0000
0.000 0+0 >= 0 = Acceptable
(using Weld 41 only) 0 >= 0.25 = ERROR
0 #N/A #N/A #N/A #N/A #N/A
Calculated nozzle weight (LBS): 0.00 #N/A #N/A #N/A #N/A #N/A
Nozzle & Flange overide weight (LBS): 0.00
Note: Attached piping to be externally supported. Calculations are limited to materials listed in this sheet.
CALCULATIONS FOR ASME CODE SECTION VIII, DIVISION I, 2017 EDITION
PRESSURE VESSEL CALCULATIONS
WORKBOOK VERSION: 09222018b

Shell Nozzle and Repad (Not Required) 10/24/2018 Page 1 of 2


NOZZLE 4 -- NOT USED 0 INCH/PSI OTHER
JOB NO: 0 NOZZLE ID. QUANTITY= 0
Shell Inputs: FLANGE/COUPLING RATING 0 PSI
INHERENT Material
#N/A Sv [psi] - allowable stress
0.85 E1 - efficiency of shell at nozzle

0.000 Ds [in] - inside diameter of shell/cone at nozzle


0.000 nt [in] - nominal shell wall thickness
#N/A Treq [in] - required shell wall thickness at nozzle
0.000 sca [in] - shell corrosion allowance
0.063 tUG16(b) [in] - minimum thickness per UG-16 b
Nozzle Inputs:
INHERENT Material
0 Sn [psi] - allowable stress
1.00 E - nozzle efficiency

0.000 Do [in] - outside diameter of nozzle


0.0000 Nwall [in] - nominal wall thickness of nozzle
0.0000 Ln [in] - nozzle distance from cone ODL
0.0000 CLn [in] - nozzle offset from vessel centerline
0.000 Lp [in] - exterior projection of nozzle
0.000 Ip [in] - interior projection of nozzle
0.000 nca [in] - nozzle corrosion allowance
0.0% UTP [%] - undertolerance allowance
0.0 Pn [psi] - interior pressure

Reinforcement:
INHERENT Material
#N/A Sp [psi] - allowable stress of repad
0.0000 te [in] - repad thickness 0.000
0.000 Dp [in] - outside diameter
0.000 Leg41 [in] - fillet size
0.000 Leg42 [in] - fillet size
0.000 Leg43 [in] - fillet size
0.000 LegG [in] - depth of groove
Variables:
UT [in] = Nwall*UTP 0*0 = 0.000
Rn [in] = Do/2 - (Nwall-nca) + UT 0/2 - (0-0) + 0 = 0.000
ti [in] = Nwall-2*nca 0-2*0 = 0.000
h [in] = MIN(Ip-sca,2.5*nt,2.5*ti) MIN(0-0,2.5*0,2.5*0) = 0.000
tn [in] = Nwall-nca 0-0 = 0.000
d [in] = ((Tangent Do+Cone Do)/2)-(2*tn) (0+0)/2)-(2*0) = 0.000 REQUIRED
fr1 = MIN(Sn/Sv,1) #N/A #N/A
fr2 = MIN(Sn/Sv,1) #N/A #N/A
fr3 = MIN(Sn/Sv,Sp/Sv,1) #N/A #N/A
fr4 = MIN(Sp/Sv,1) #N/A #N/A
Required Thickness: UG-27(c)(1,2)
TreqN [in] = (Pn*Rn)/(Sn*E - 0.6*Pn)+nca ~~ required minimum thickness
(0*0)/(0*1 - 0.6*0)+0 = #DIV/0!
trnR [in] = (Pn*Rn)/(Sn*1 - 0.6*Pn) (0*0)/(0*1 - 0.6*0) = #DIV/0!
CheckTreqN = TreqN <= Nwall #DIV/0! #DIV/0!
UG-45:
Tstd [in] = thickness standard wall pipe VLOOKUP(0,PIpeWall,2) = #N/A
Nact [in] = Nwall * (1-UTP) 0 * (1-0) = 0.000

UG45 [in] = Max(UG45a, UG45b) ~~ required thickness per UG-45 #DIV/0! #DIV/0!
UG45a [in] = trnR + nca #DIV/0! #DIV/0!
UG45b [in] = Min(UG45b3,UG45b4) #N/A #N/A
Shell Nozzle 4 Page 2 of 2

UG45b1 [in] = Max(Treq+sca,tUG16(b) + sca) #N/A #N/A


UG45b2 [in] = 0 0 = 0.000
UG45b3 [in] = Max(UG45b1,UG45b2) #N/A #N/A
UG45b4 [in] = Tstd*0.875 + nca #N/A #N/A
CheckUG45 = UG45 <= Nact #DIV/0! #DIV/0!
#DIV/0!
Minimum thickness per UG-45 [in] = #N/A #N/A

Area Replacement:
Ar [in^2] = 1*d*Treq*1+2*tn*Treq*1*(1-fr1) ~~ required Area
#N/A #N/A
A1 [in^2] = max(d, 2*(nt+tn)) * (E1*nt-1*Treq)-2*tn*(E1*nt-1*Treq)*(1-fr1)
#N/A #N/A
A2 [in^2] = min((tn-trnR)*fr2*min(5*nt,2*Lp),(tn-trnR)*(Min(2.5*tn+te,2*Lp)*fr2*2))
#DIV/0! #DIV/0!
A3 [in^2] = Min(5*nt*ti*fr2,5*ti*ti*fr2,2*h*ti*fr2)
#N/A #N/A
A5 [in^2] = (Dp-d-2*tn)*te*fr4 N/A = 0.000
A41 [in^2] = Leg41^2*fr3 #N/A #N/A
A42 [in^2] = Leg42^2*fr4 #N/A #N/A
A43 [in^2] = (Leg43-nca)^2*fr2 #N/A #N/A
Aa [in^2] = A1+A2+A3+A5+A41+A42+A43 ~~ actual area
#N/A #N/A
CheckA = Aa >= Ar ~~ check area replacement #N/A #N/A

Nozzle Weld Strength: per UW-16(a), (b)


Weld 41 tmin [in] = smaller of 0.75, nt, or Nwall 0.000 0.000 0.000 = 0.0000
Weld 41 Leg [in] = smaller of 0.25 or (tmin * 0.7) / 0.7 0 = 0.0000
0 >= 0 = ERROR
Weld 42 tmin [in] = (smaller of 0.5nt or te) 0.000 = 0.0000
Weld 42 Leg [in] = (smaller of 0.25 or (temin * 0.7) / 0.7) 0 = 0.0000
0 0 >= 0 = N/A
Weld 43 Leg [in] = (smaller of 0.25 or (tmin * 0.7) / 0.7) + sca = 0.0000
0 0 >= 0 = N/A

Cone Required Thickness at Nozzle 4: VIII-1 App 1-4 e)


Treq [in] = P*ODL/(2*COS(a)*(S*E+0.4*P)) + Corr ~~required minimum thickness
#DIV/0! N/A
O.D. of cone at nozzle: 0 Cone ODL side of nozzle 0 (in)
0.000 Center of nozzle 0 (in)
0 0 Cone ODS side of nozzle 0 (in)
Shell or cone straight nozzle: Large nozzle diameter 0.000 (in)
Shell or cone tangent nozzle: Large nozzle diameter 0.000 (in)
Added nozzle cut length: 0.000 (in)

Minimum design temperature check: Impact testing exempt to -20F per UG20(f)
UCS-66 CURVE 'B' RATING [F]: #N/A

Nozzle Weld Strength: per UW-16(i) (using Weld 41 only)

Weld 41 + Weld 43 tmin [in] = smaller of 1.25 * nt, or Nwall (0.25" min)
0.000 0 * 1.25 = 0.0000
0+0 >= 0 = Acceptable
(using Weld 41 only) 0 >= 0.25 = ERROR

0 #N/A #N/A #N/A #N/A #N/A


Calculated nozzle weight (LBS): 0.00 #N/A #N/A #N/A #N/A #N/A
Nozzle & Flange overide weight (LBS): 0.00
Note: Attached piping to be externally supported. Calculations are limited to materials listed in this sheet.
YOUR COMPANY NAME
CALCULATIONS FOR ASME CODE SECTION VIII, DIVISION I, 2017 EDITION
PRESSURE VESSEL CALCULATIONS
WORKBOOK VERSION: 09222018b

Shell Nozzle and Repad (Not Required) 10/24/2018 Page 1 of 2


NOZZLE 5 -- NOT USED 0 INCH/PSI OTHER
JOB NO: 0 NOZZLE ID. QUANTITY= 0
Shell Inputs: FLANGE/COUPLING RATING 0 PSI
INHERENT Material
#N/A Sv [psi] - allowable stress
0.85 E1 - efficiency of shell at nozzle
0.000 Ds [in] - inside diameter of shell/cone at nozzle
0.000 nt [in] - nominal shell wall thickness
#N/A Treq [in] - required shell wall thickness at nozzle
0.000 sca [in] - shell corrosion allowance
0.063 tUG16(b) [in] - minimum thickness per UG-16 b
Nozzle Inputs:
INHERENT Material
0 Sn [psi] - allowable stress
1.00 E - nozzle efficiency
0.000 Do [in] - outside diameter of nozzle
0.0000 Nwall [in] - nominal wall thickness of nozzle
0.0000 Ln [in] - nozzle distance from cone ODL
0.0000 CLn [in] - nozzle offset from vessel centerline
0.000 Lp [in] - exterior projection of nozzle
0.000 Ip [in] - interior projection of nozzle
0.000 nca [in] - nozzle corrosion allowance
0.0% UTP [%] - undertolerance allowance
0.0 Pn [psi] - interior pressure
Reinforcement:
INHERENT Material
#N/A Sp [psi] - allowable stress of repad
0.0000 te [in] - repad thickness 0.000
0.000 Dp [in] - outside diameter
0.000 Leg41 [in] - fillet size
0.000 Leg42 [in] - fillet size
0.000 Leg43 [in] - fillet size
0.000 LegG [in] - depth of groove
Variables:
UT [in] = Nwall*UTP 0*0 = 0.000
Rn [in] = Do/2 - (Nwall-nca) + UT 0/2 - (0-0) + 0 = 0.000
ti [in] = Nwall-2*nca 0-2*0 = 0.000
h [in] = MIN(Ip-sca,2.5*nt,2.5*ti) MIN(0-0,2.5*0,2.5*0) = 0.000
tn [in] = Nwall-nca 0-0 = 0.000
d [in] = ((Tangent Do+Cone Do)/2)-(2*tn) (0+0)/2)-(2*0) = 0.000 REQUIRED
fr1 = MIN(Sn/Sv,1) #N/A #N/A
fr2 = MIN(Sn/Sv,1) #N/A #N/A
fr3 = MIN(Sn/Sv,Sp/Sv,1) #N/A #N/A
fr4 = MIN(Sp/Sv,1) #N/A #N/A
Required Thickness: UG-27(c)(1,2)
TreqN [in] = (Pn*Rn)/(Sn*E - 0.6*Pn)+nca ~~ required minimum thickness
(0*0)/(0*1 - 0.6*0)+0 = #DIV/0!
trnR [in] = (Pn*Rn)/(Sn*1 - 0.6*Pn) (0*0)/(0*1 - 0.6*0) = #DIV/0!
CheckTreqN = TreqN <= Nwall #DIV/0! #DIV/0!

UG-45:
Tstd [in] = thickness standard wall pipe VLOOKUP(0,PIpeWall,2) = #N/A
Nact [in] = Nwall * (1-UTP) 0 * (1-0) = 0.000
Shell nozzle 5 Page 2

UG45 [in] = Max(UG45a, UG45b) ~~ required thickness per UG-45 #DIV/0!#DIV/0!


UG45a [in] = trnR + nca #DIV/0!#DIV/0!
UG45b [in] = Min(UG45b3,UG45b4) #N/A #N/A
UG45b1 [in] = Max(Treq+sca,tUG16(b) + sca) #N/A #N/A
UG45b2 [in] = 0 0= 0.000
UG45b3 [in] = Max(UG45b1,UG45b2) #N/A #N/A
UG45b4 [in] = Tstd*0.875 + nca #N/A #N/A
CheckUG45 = UG45 <= Nact #DIV/0!#DIV/0!
#DIV/0!
Minimum thickness per UG-45 [in] = #N/A #N/A

Area Replacement:
Ar [in^2] = 1*d*Treq*1+2*tn*Treq*1*(1-fr1) ~~ required Area
#N/A #N/A
A1 [in^2] = max(d, 2*(nt+tn)) * (E1*nt-1*Treq)-2*tn*(E1*nt-1*Treq)*(1-fr1)
#N/A #N/A
A2 [in^2] = min((tn-trnR)*fr2*min(5*nt,2*Lp),(tn-trnR)*(Min(2.5*tn+te,2*Lp)*fr2*2))
#DIV/0! #DIV/0!
A3 [in^2] = Min(5*nt*ti*fr2,5*ti*ti*fr2,2*h*ti*fr2)
#N/A #N/A
A5 [in^2] = (Dp-d-2*tn)*te*fr4 N/A = 0.000
A41 [in^2] = Leg41^2*fr3 #N/A #N/A
A42 [in^2] = Leg42^2*fr4 #N/A #N/A
A43 [in^2] = (Leg43-nca)^2*fr2 #N/A #N/A
Aa [in^2] = A1+A2+A3+A5+A41+A42+A43 ~~ actual area
#N/A #N/A
CheckA = Aa >= Ar ~~ check area replacement #N/A #N/A

Nozzle Weld Strength: per UW-16(a), (b)


Weld 41 tmin [in] = smaller of 0.75, nt, or Nwall 0.000 0.000 0.000 = 0.0000
Weld 41 Leg [in] = smaller of 0.25 or (tmin * 0.7) / 0.7 0 = 0.0000
0 >= 0 = ERROR
Weld 42 tmin [in] = (smaller of 0.5nt or te) 0.000 = 0.0000
Weld 42 Leg [in] = (smaller of 0.25 or (temin * 0.7) / 0.7) 0 = 0.0000
0 0 >= 0 = N/A
Weld 43 Leg [in] = (smaller of 0.25 or (tmin * 0.7) / 0.7) + sca = 0.0000
0 0 >= 0 = N/A
Cone Required Thickness at Nozzle: VIII-1 App 1-4 e)
Treq [in] = P*ODL/(2*COS(a)*(S*E+0.4*P)) + Corr ~~required minimum thickness
#DIV/0! N/A
O.D. of cone at nozzle: 0 Cone ODL side of nozzle 0 (in)
0.000 Center of nozzle 0 (in)
0 0 Cone ODS side of nozzle 0 (in)
Shell or cone straight nozzle: Large nozzle diameter 0.000 (in)
Shell or cone tangent nozzle: Large nozzle diameter 0.000 (in)
Added nozzle cut length: 0.000 (in)

Minimum design temperature check: Impact testing exempt to -20F per UG20(f)
UCS-66 CURVE 'B' RATING [F]: #N/A

Nozzle Weld Strength: per UW-16(i) (using Weld 41 only)

Weld 41 + Weld 43 tmin [in] = smaller of 1.25 * nt, or Nwall (0.25" min)
0.000 0 * 1.25 = 0.0000
0+0 >= 0 = Acceptable
(using Weld 41 only) 0 >= 0.25 = ERROR
0 #N/A #N/A #N/A #N/A #N/A
Calculated nozzle weight (LBS): 0.00 #N/A #N/A #N/A #N/A #N/A
Nozzle & Flange overide weight (LBS): 0.00
Note: Attached piping to be externally supported. Calculations are limited to materials listed in this sheet.
YOUR COMPANY NAME
CALCULATIONS FOR ASME CODE SECTION VIII, DIVISION I, 2017 EDITION
PRESSURE VESSEL CALCULATIONS
WORKBOOK VERSION: 09222018b

Head Nozzle and Repad (Not Required) 10/24/2018 Page 1 of 2


HEAD A NOZZLE 1 -- NOT USED NOZZLE ID. 0 INCH/PSI OTHER
JOB NO: 0 QTY= 0 FLANGE/COUPLING RATING 0 PSI
Head Inputs: HEAD A (END) ELLIPTICAL (Nozzles within 80% limit only)
SA-36 Material
16,600 Sv [psi] - allowable stress
0.85 E1 - efficiency of head at nozzle
0.000 Ds [in] - inside head dish diameter
0.000 nt [in] - nominal head wall thickness
0.000 Treq [in] - required head wall thickness at nozzle
0.000 sca [in] - shell/head corrosion allowance
0.063 tUG16(b) [in] - minimum thickness per UG-16 b
Nozzle Inputs: HEAD
INHERENT Material
0 Sn [psi] - allowable stress
1.00 E - nozzle efficiency
0.000 Do [in] - outside diameter of nozzle
0.000 Nwall [in] - nominal wall thickness of nozzle
0.0000 Ln [in] - nozzle distance from cone ODL
0.0000 CLn [in] - nozzle offset from Cone centerline
0.000 Lp [in] - exterior projection of nozzle
0.000 Ip [in] - interior projection of nozzle
0.000 nca [in] - nozzle corrosion allowance
0.0% UTP [%] - undertolerance allowance
0.0 Pn [psi] - interior pressure

Reinforcement:
INHERENT Material
16,600 Sp [psi] - allowable stress of repad
0.0000 te [in] - repad thickness 0.000
0.000 Dp [in] - outside diameter
0.000 Leg41 [in] - fillet size
0.000 Leg42 [in] - fillet size
0.000 Leg43 [in] - fillet size
0.000 LegG [in] - depth of groove
Variables:
UT [in] = Nwall*UTP 0*0 = 0.000
Rn [in] = Do/2 - (Nwall-nca) + UT 0/2 - (0-0) + 0 = 0.000
ti [in] = Nwall-2*nca 0-2*0 = 0.000
h [in] = MIN(Ip-sca,2.5*nt,2.5*ti) MIN(0-0,2.5*0,2.5*0) = 0.000
tn [in] = Nwall-nca 0-0 = 0.000
d [in] = ((Tangent or nozzle Do+Cone Do)/2)-(2*tn) (0+0)/2)-(2*0) = 0.000 REQUIRED
fr1 = MIN(Sn/Sv,1) MIN(0/16600,1) = 0.000
fr2 = MIN(Sn/Sv,1) MIN(0/16600,1) = 0.000
fr3 = MIN(Sn/Sv,Sp/Sv,1) MIN(0/16600,16600/16600,1) = 0.000
fr4 = MIN(Sp/Sv,1) MIN(16600/16600,1) = 1.000
Required Thickness: UG-27(c)(1,2)
TreqN [in] = (Pn*Rn)/(Sn*E - 0.6*Pn)+nca ~~ required minimum thickness
(0*0)/(0*1 - 0.6*0)+0 = #DIV/0!
trnR [in] = (Pn*Rn)/(Sn*1 - 0.6*Pn) (0*0)/(0*1 - 0.6*0) = #DIV/0!
CheckTreqN = TreqN <= Nwall #DIV/0! #DIV/0!
UG-45:
Tstd [in] = thickness stan thickness standard wall pipe VLOOKUP(0,PIpeWall,2) = #N/A
Nact [in] = Nwall * (1-UTP) 0 * (1-0) = 0.000
UG45 [in] = Max(UG45a, UG45b) ~~ required thickness per UG-45 #DIV/0! #DIV/0!
UG45a [in] = trnR + nca #DIV/0! #DIV/0!
Head A Nozzle 1 Page 2 of 2

UG45b [in] = Min(UG45b3,UG45b4) #N/A #N/A


UG45b1 [in] = Max(Treq+sca,tUG16(b) + sca) MAX(0+0,0.063 + 0) = 0.063
UG45b2 [in] = 0 0= 0.000
UG45b3 [in] = Max(UG45b1,UG45b2) MAX(0.063,0) = 0.063
UG45b4 [in] = Tstd*0.875 + nca #N/A #N/A
CheckUG45 = UG45 <= Nact #DIV/0! #DIV/0!
#DIV/0!
Minimum thickness per UG-45 [in] = #N/A #N/A

Area Replacement:
Ar [in^2] = 1*d*Treq*1+2*tn*Treq*1*(1-fr1) ~~ required Area
1*0*0*1+2*0*0*1*(1-0) = 0.000
A1 [in^2] = max(d, 2*(nt+tn)) * (E1*nt-1*Treq)-2*tn*(E1*nt-1*Treq)*(1-fr1)
MAX(0, 2*(0+0)) * (0.85*0-1*0)-2*0*(0.85*0-1*0)*(1-0) = 0.000
A2 [in^2] = min((tn-trnR)*fr2*min(5*nt,2*Lp),(tn-trnR)*(Min(2.5*tn+te,2*Lp)*fr2*2))
#DIV/0! #DIV/0!
A3 [in^2] = Min(5*nt*ti*fr2,5*ti*ti*fr2,2*h*ti*fr2)
MIN(5*0*0*0,5*0*0*0,2*0*0*0) = 0.000
A5 [in^2] = (Dp-d-2*tn)*te*fr4 N/A = 0.000
A41 [in^2] = Leg41^2*fr3 0^2*0 = 0.000
A42 [in^2] = Leg42^2*fr4 0^2*1 = 0.000
A43 [in^2] = (Leg43-nca)^2*fr2 (0-0)^2*0 = 0.000
Aa [in^2] = A1+A2+A3+A5+A41+A42+A43 ~~ actual area
#DIV/0! #DIV/0!
CheckA = Aa >= Ar ~~ check area replacement #DIV/0! #DIV/0!

Nozzle Weld Strength: per UW-16(a), (b)


Weld 41 tmin [in] = smaller of 0.75, nt, or Nwall 0.000 0.000 0.000 = 0.0000
Weld 41 Leg [in] = smaller of 0.25 or (tmin * 0.7) / 0.7 0 = 0.0000
0 >= 0 = ERROR
Weld 42 tmin [in] = (smaller of 0.5nt or te) 0.000 = 0.0000
Weld 42 Leg [in] = (smaller of 0.25 or (temin * 0.7) / 0.7) 0 = 0.0000
0 0 >= 0 = N/A
Weld 43 Leg [in] = (smaller of 0.25 or (tmin * 0.7) / 0.7) + sca = 0.0000
0 0 >= 0 = N/A

Cone Required Thickness at Head A Nozzle 1: VIII-1 App 1-4 e)


Treq [in] = P*ODL/(2*COS(a)*(S*E+0.4*P)) + Corr ~~required minimum thickness
#DIV/0! 0.000
O.D. of cone at nozzle: 0 Cone ODL side of nozzle N/A (in)
0.000 Center of nozzle N/A (in)
#VALUE! 0 Cone ODS side of nozzle N/A (in)
Cone straight nozzle: Large nozzle diameter 0.000 (in)
Cone tangent nozzle: Large nozzle diameter 0.000 (in)
Added nozzle cut length: 0.000

Minimum design temperature check: Impact testing exempt to -20F per UG20(f)
UCS-66 CURVE 'B' RATING [F]: #N/A

Nozzle Weld Strength: per UW-16(i) (using Weld 41 only)

Weld 41 + Weld 43 tmin [in] = smaller of 1.25 * nt, or Nwall (0.25" min)
0.000 0 * 1.25 = 0.0000
0+0 >= 0 = Acceptable
(using Weld 41 only) 0 >= 0.25 = ERROR

0 #N/A #N/A #N/A #N/A #N/A


Calculated nozzle weight (LBS): 0.00 #N/A #N/A #N/A #N/A #N/A
Nozzle & Flange overide weight (LBS): 0.00
Note: Attached piping to be externally supported. Calculations are limited to materials listed in this sheet.
YOUR COMPANY NAME
CALCULATIONS FOR ASME CODE SECTION VIII, DIVISION I, 2017 EDITION
PRESSURE VESSEL CALCULATIONS
WORKBOOK VERSION: 09222018b

Head Nozzle and Repad (Not Required) 10/24/2018 Page 1 of 2


HEAD A NOZZLE 2 -- NOT USED NOZZLE ID. 0 INCH/PSI OTHER
JOB NO: 0 QTY= 0 FLANGE/COUPLING RATING 0 PSI
Head Inputs: HEAD A (END) ELLIPTICAL (Nozzles within 80% limit only)
SA-36 Material
16,600 Sv [psi] - allowable stress
0.85 E1 - efficiency of head at nozzle

0.000 Ds [in] - inside head dish diameter


0.000 nt [in] - nominal head wall thickness
0.000 Treq [in] - required wall thickness at nozzle
0.000 sca [in] - shell/head corrosion allowance
0.063 tUG16(b) [in] - minimum thickness per UG-16 b
Nozzle Inputs: ERROR
INHERENT Material
0 Sn [psi] - allowable stress
1.00 E - nozzle efficiency

0.000 Do [in] - outside diameter of nozzle


0.000 Nwall [in] - nominal wall thickness of nozzle
0.0000 Ln [in] - nozzle distance from cone ODL
0.0000 CLn [in] - nozzle offset from Cone centerline
0.000 Lp [in] - exterior projection of nozzle
0.000 Ip [in] - interior projection of nozzle
0.000 nca [in] - nozzle corrosion allowance
0.0% UTP [%] - undertolerance allowance
0.0 Pn [psi] - interior pressure

Reinforcement:
INHERENT Material
16,600 Sp [psi] - allowable stress of repad
0.0000 te [in] - repad thickness 0.000
0.000 Dp [in] - outside diameter
0.000 Leg41 [in] - fillet size
0.000 Leg42 [in] - fillet size
0.000 Leg43 [in] - fillet size
0.000 LegG [in] - depth of groove
Variables:
UT [in] = Nwall*UTP 0*0 = 0.000
Rn [in] = Do/2 - (Nwall-nca) + UT 0/2 - (0-0) + 0 = 0.000
ti [in] = Nwall-2*nca 0-2*0 = 0.000
h [in] = MIN(Ip-sca,2.5*nt,2.5*ti) MIN(0-0,2.5*0,2.5*0) = 0.000
tn [in] = Nwall-nca 0-0 = 0.000
d [in] = ((Tangent or nozzle Do+Cone Do)/2)-(2*tn) (0+0)/2)-(2*0) = 0.000 REQUIRED
fr1 = MIN(Sn/Sv,1) MIN(0/16600,1) = 0.000
fr2 = MIN(Sn/Sv,1) MIN(0/16600,1) = 0.000
fr3 = MIN(Sn/Sv,Sp/Sv,1) MIN(0/16600,16600/16600,1) = 0.000
fr4 = MIN(Sp/Sv,1) MIN(16600/16600,1) = 1.000
Required Thickness: UG-27(c)(1,2)
TreqN [in] = (Pn*Rn)/(Sn*E - 0.6*Pn)+nca ~~ required minimum thickness
(0*0)/(0*1 - 0.6*0)+0 = #DIV/0!
trnR [in] = (Pn*Rn)/(Sn*1 - 0.6*Pn) (0*0)/(0*1 - 0.6*0) = #DIV/0!
CheckTreqN = TreqN <= Nwall #DIV/0! #DIV/0!
UG-45:
Tstd [in] = thickness stan thickness standard wall pipe VLOOKUP(0,PIpeWall,2) = #N/A
Nact [in] = Nwall * (1-UTP) 0 * (1-0) = 0.000

UG45 [in] = Max(UG45a, UG45b) ~~ required thickness per UG-45 #DIV/0! #DIV/0!
UG45a [in] = trnR + nca #DIV/0! #DIV/0!
Head A Nozzle 2 Page 2 of 2

UG45b [in] = Min(UG45b3,UG45b4) #N/A #N/A


UG45b1 [in] = Max(Treq+sca,tUG16(b) + sca) MAX(0+0,0.063 + 0) = 0.063
UG45b2 [in] = 0 0= 0.000
UG45b3 [in] = Max(UG45b1,UG45b2) MAX(0.063,0) = 0.063
UG45b4 [in] = Tstd*0.875 + nca #N/A #N/A
CheckUG45 = UG45 <= Nact #DIV/0! #DIV/0!
#DIV/0!
Minimum thickness per UG-45 [in] = #N/A #N/A

Area Replacement:
Ar [in^2] = 1*d*Treq*1+2*tn*Treq*1*(1-fr1) ~~ required Area
1*0*0*1+2*0*0*1*(1-0) = 0.000
A1 [in^2] = max(d, 2*(nt+tn)) * (E1*nt-1*Treq)-2*tn*(E1*nt-1*Treq)*(1-fr1)
MAX(0, 2*(0+0)) * (0.85*0-1*0)-2*0*(0.85*0-1*0)*(1-0) = 0.000
A2 [in^2] = min((tn-trnR)*fr2*min(5*nt,2*Lp),(tn-trnR)*(Min(2.5*tn+te,2*Lp)*fr2*2))
#DIV/0! #DIV/0!
A3 [in^2] = Min(5*nt*ti*fr2,5*ti*ti*fr2,2*h*ti*fr2)
MIN(5*0*0*0,5*0*0*0,2*0*0*0) = 0.000
A5 [in^2] = (Dp-d-2*tn)*te*fr4 N/A = 0.000
A41 [in^2] = Leg41^2*fr3 0^2*0 = 0.000
A42 [in^2] = Leg42^2*fr4 0^2*1 = 0.000
A43 [in^2] = (Leg43-nca)^2*fr2 (0-0)^2*0 = 0.000
Aa [in^2] = A1+A2+A3+A5+A41+A42+A43 ~~ actual area
#DIV/0! #DIV/0!
CheckA = Aa >= Ar ~~ check area replacement #DIV/0! #DIV/0!

Nozzle Weld Strength: per UW-16(a), (b)


Weld 41 tmin [in] = smaller of 0.75, nt, or Nwall 0.000 0.000 0.000 = 0.0000
Weld 41 Leg [in] = smaller of 0.25 or (tmin * 0.7) / 0.7 0 = 0.0000
0 >= 0 = ERROR
Weld 42 tmin [in] = (smaller of 0.5nt or te) 0.000 = 0.0000
Weld 42 Leg [in] = (smaller of 0.25 or (temin * 0.7) / 0.7) 0 = 0.0000
0 0 >= 0 = N/A
Weld 43 Leg [in] = (smaller of 0.25 or (tmin * 0.7) / 0.7) + sca = 0.0000
0 0 >= 0 = N/A

Cone Required Thickness at Head A Nozzle 2: VIII-1 App 1-4 e)


Treq [in] = P*ODL/(2*COS(a)*(S*E+0.4*P)) + Corr ~~required minimum thickness
#DIV/0! 0.000
O.D. of cone at nozzle: 0 Cone ODL side of nozzle N/A (in)
0.000 Center of nozzle N/A (in)
#VALUE! 0 Cone ODS side of nozzle N/A (in)
Cone straight nozzle: Large nozzle diameter 0.000 (in)
Cone tangent nozzle: Large nozzle diameter 0.000 (in)
Added nozzle cut length: 0.000

Minimum design temperature check: Impact testing exempt to -20F per UG20(f)
UCS-66 CURVE 'B' RATING [F]: #N/A

Nozzle Weld Strength: per UW-16(i) (using Weld 41 only)

Weld 41 + Weld 43 tmin [in] = smaller of 1.25 * nt, or Nwall (0.25" min)
0.000 0 * 1.25 = 0.0000
0+0 >= 0 = Acceptable
0 >= 0.25 = ERROR
(using Weld 41 only)
0 #N/A #N/A #N/A #N/A #N/A
Calculated nozzle weight (LBS): 0.00 #N/A #N/A #N/A #N/A #N/A
Nozzle & Flange overide weight (LBS): 0.00
Note: Attached piping to be externally supported. Calculations are limited to materials listed in this sheet.
YOUR COMPANY NAME
CALCULATIONS FOR ASME CODE SECTION VIII, DIVISION I, 2017 EDITION
PRESSURE VESSEL CALCULATIONS
WORKBOOK VERSION: 09222018b

Head Nozzle and Repad (Not Required) 10/24/2018 Page 1 of 2


HEAD A NOZZLE 3 -- NOT USED NOZZLE ID. 0 INCH/PSI OTHER
JOB NO: 0 QTY= 0 FLANGE/COUPLING RATING 0 PSI
Head Inputs: HEAD A (END) ELLIPTICAL (Nozzles within 80% limit only)
SA-36 Material
16,600 Sv [psi] - allowable stress
0.85 E1 - efficiency of head at nozzle
0.000 Ds [in] - inside head dish/cone diameter at nozzle
0.000 nt [in] - nominal head wall thickness
0.000 Treq [in] - required wall thickness at nozzle
0.000 sca [in] - shell/head corrosion allowance
0.063 tUG16(b) [in] - minimum thickness per UG-16 b
Nozzle Inputs: ERROR
INHERENT Material
0 Sn [psi] - allowable stress
1.00 E - nozzle efficiency
0.000 Do [in] - outside diameter of nozzle
0.000 Nwall [in] - nominal wall thickness of nozzle
0.000 Lp [in] - exterior projection of nozzle
0.000 Ip [in] - interior projection of nozzle
0.000 nca [in] - nozzle corrosion allowance
0.0% UTP [%] - undertolerance allowance
0.0 Pn [psi] - interior pressure

Reinforcement:
INHERENT Material
16,600 Sp [psi] - allowable stress of repad
0.0000 te [in] - repad thickness 0.000
0.000 Dp [in] - outside diameter
0.000 Leg41 [in] - fillet size
0.000 Leg42 [in] - fillet size
0.000 Leg43 [in] - fillet size
0.000 LegG [in] - depth of groove
Variables:
UT [in] = Nwall*UTP 0*0 = 0.000
Rn [in] = Do/2 - (Nwall-nca) + UT 0/2 - (0-0) + 0 = 0.000
ti [in] = Nwall-2*nca 0-2*0 = 0.000
h [in] = MIN(Ip-sca,2.5*nt,2.5*ti) MIN(0-0,2.5*0,2.5*0) = 0.000
tn [in] = Nwall-nca 0-0 = 0.000
d [in] = Do-2*tn 0-2*0 = 0.000
fr1 = MIN(Sn/Sv,1) MIN(0/16600,1) = 0.000
fr2 = MIN(Sn/Sv,1) MIN(0/16600,1) = 0.000
fr3 = MIN(Sn/Sv,Sp/Sv,1) MIN(0/16600,16600/16600,1) = 0.000
fr4 = MIN(Sp/Sv,1) MIN(16600/16600,1) = 1.000
Required Thickness: UG-27(c)(1,2)
TreqN [in] = (Pn*Rn)/(Sn*E - 0.6*Pn)+nca ~~ required minimum thickness
(0*0)/(0*1 - 0.6*0)+0 = #DIV/0!
trnR [in] = (Pn*Rn)/(Sn*1 - 0.6*Pn) (0*0)/(0*1 - 0.6*0) = #DIV/0!
CheckTreqN = TreqN <= Nwall #DIV/0! #DIV/0!
UG-45:
Tstd [in] = thickness standthickness standard wall pipe VLOOKUP(0,PIpeWall,2) = #N/A
Nact [in] = Nwall * (1-UTP) 0 * (1-0) = 0.000
UG45 [in] = Max(UG45a, UG45b) ~~ required thickness per UG-45 #DIV/0! #DIV/0!
UG45a [in] = trnR + nca #DIV/0! #DIV/0!
UG45b [in] = Min(UG45b3,UG45b4) #N/A #N/A

Head A Nozzle 3 Page 2 of 2

UG45b1 [in] = Max(Treq+sca,tUG16(b) + sca) MAX(0+0,0.063 + 0) = 0.063


UG45b2 [in] = 0 0= 0.000
UG45b3 [in] = Max(UG45b1,UG45b2) MAX(0.063,0) = 0.063
UG45b4 [in] = Tstd*0.875 + nca #N/A #N/A
CheckUG45 = UG45 <= Nact #DIV/0! #DIV/0!
#DIV/0!
Minimum thickness per UG-45 [in] = #N/A #N/A

Area Replacement:
Ar [in^2] = 1*d*Treq*1+2*tn*Treq*1*(1-fr1) ~~ required Area
1*0*0*1+2*0*0*1*(1-0) = 0.000
A1 [in^2] = max(d, 2*(nt+tn)) * (E1*nt-1*Treq)-2*tn*(E1*nt-1*Treq)*(1-fr1)
MAX(0, 2*(0+0)) * (0.85*0-1*0)-2*0*(0.85*0-1*0)*(1-0) = 0.000
A2 [in^2] = min((tn-trnR)*fr2*min(5*nt,2*Lp),(tn-trnR)*(Min(2.5*tn+te,2*Lp)*fr2*2))
#DIV/0! #DIV/0!
A3 [in^2] = Min(5*nt*ti*fr2,5*ti*ti*fr2,2*h*ti*fr2)
MIN(5*0*0*0,5*0*0*0,2*0*0*0) = 0.000
A5 [in^2] = (Dp-d-2*tn)*te*fr4 N/A = 0.000
A41 [in^2] = Leg41^2*fr3 0^2*0 = 0.000
A42 [in^2] = Leg42^2*fr4 0^2*1 = 0.000
A43 [in^2] = (Leg43-nca)^2*fr2 (0-0)^2*0 = 0.000
Aa [in^2] = A1+A2+A3+A5+A41+A42+A43 ~~ actual area
#DIV/0! #DIV/0!
CheckA = Aa >= Ar ~~ check area replacement #DIV/0! #DIV/0!

Nozzle Weld Strength: per UW-16(a), (b)


Weld 41 tmin [in] = smaller of 0.75, nt, or Nwall 0.000 0.000 0.000 = 0.0000
Weld 41 Leg [in] = smaller of 0.25 or (tmin * 0.7) / 0.7 0 = 0.0000
0 >= 0 = ERROR
Weld 42 tmin [in] = (smaller of 0.5nt or te) 0.000 = 0.0000
Weld 42 Leg [in] = (smaller of 0.25 or (temin * 0.7) / 0.7) 0 = 0.0000
0 0 >= 0 = NA
Weld 43 Leg [in] = (smaller of 0.25 or (tmin * 0.7) / 0.7) + sca = 0.0000
0 0 >= 0 = N/A
Minimum design temperature check: Impact testing exempt to -20F per UG20(f)
UCS-66 CURVE 'B' RATING [F]: #N/A

Nozzle Weld Strength: per UW-16(i) (using Weld 41 only)

Weld 41 + Weld 43 tmin [in] = smaller of 1.25 * nt, or Nwall (0.25" min)
0.000 0 * 1.25 = 0.0000
0+0 >= 0 = Acceptable
0 >= 0.25 = ERROR
(using Weld 41 only)
0 #N/A #N/A #N/A #N/A #N/A
Calculated nozzle weight (LBS): 0.00 #N/A #N/A #N/A #N/A #N/A
Nozzle & Flange overide weight (LBS): 0.00
Note: Attached piping to be externally supported. Calculations are limited to materials listed in this sheet.
YOUR COMPANY NAME
CALCULATIONS FOR ASME CODE SECTION VIII, DIVISION I, 2017 EDITION
PRESSURE VESSEL CALCULATIONS
WORKBOOK VERSION: 09222018b

Head Nozzle and Repad (Not Required) 10/24/2018 Page 1 of 2


HEAD B NOZZLE 1 -- NOT USED NOZZLE ID. 0 INCH/PSI OTHER
JOB NO: 0 QTY= 0 FLANGE/COUPLING RATING 0 PSI
Head Inputs: HEAD B (END) ELLIPTICAL (Nozzles within 80% limit only)
SA-36 Material
16,600 Sv [psi] - allowable stress
0.85 E1 - efficiency of head at nozzle
0.000 Ds [in] - inside head dish diameter
0.000 nt [in] - nominal head wall thickness
0.000 Treq [in] - required head wall thickness
0.000 sca [in] - shell/head corrosion allowance
0.063 tUG16(b) [in] - minimum thickness per UG-16 b
Nozzle Inputs: ERROR
INHERENT Material
0 Sn [psi] - allowable stress
1.00 E - nozzle efficiency
0.000 Do [in] - outside diameter of nozzle
0.000 Nwall [in] - nominal wall thickness of nozzle
0.0000 Ln [in] - nozzle distance from cone ODL
0.0000 CLn [in] - nozzle offset from Cone centerline
0.000 Lp [in] - exterior projection of nozzle
0.000 Ip [in] - interior projection of nozzle
0.000 nca [in] - nozzle corrosion allowance
0.0% UTP [%] - undertolerance allowance
0.0 Pn [psi] - interior pressure

Reinforcement:
INHERENT Material
16,600 Sp [psi] - allowable stress of repad
0.0000 te [in] - repad thickness 0.000
0.000 Dp [in] - outside diameter
0.000 Leg41 [in] - fillet size
0.000 Leg42 [in] - fillet size
0.000 Leg43 [in] - fillet size
0.000 LegG [in] - depth of groove
Variables:
UT [in] = Nwall*UTP 0*0 = 0.000
Rn [in] = Do/2 - (Nwall-nca) + UT 0/2 - (0-0) + 0 = 0.000
ti [in] = Nwall-2*nca 0-2*0 = 0.000
h [in] = MIN(Ip-sca,2.5*nt,2.5*ti) MIN(0-0,2.5*0,2.5*0) = 0.000
tn [in] = Nwall-nca 0-0 = 0.000
d [in] = ((Tangent or nozzle Do+Cone Do)/2)-(2*tn) (0+0)/2)-(2*0) = 0.000 REQUIRED
fr1 = MIN(Sn/Sv,1) MIN(0/16600,1) = 0.000
fr2 = MIN(Sn/Sv,1) MIN(0/16600,1) = 0.000
fr3 = MIN(Sn/Sv,Sp/Sv,1) MIN(0/16600,16600/16600,1) = 0.000
fr4 = MIN(Sp/Sv,1) MIN(16600/16600,1) = 1.000
Required Thickness: UG-27(c)(1,2)
TreqN [in] = (Pn*Rn)/(Sn*E - 0.6*Pn)+nca ~~ required minimum thickness
(0*0)/(0*1 - 0.6*0)+0 = #DIV/0!
trnR [in] = (Pn*Rn)/(Sn*1 - 0.6*Pn) (0*0)/(0*1 - 0.6*0) = #DIV/0!
CheckTreqN = TreqN <= Nwall #DIV/0! #DIV/0!
UG-45:
Tstd [in] = thickness stan thickness standard wall pipe VLOOKUP(0,PIpeWall,2) = #N/A
Nact [in] = Nwall * (1-UTP) 0 * (1-0) = 0.000
UG45 [in] = Max(UG45a, UG45b) ~~ required thickness per UG-45 #DIV/0! #DIV/0!
UG45a [in] = trnR + nca #DIV/0! #DIV/0!
HEAD B NOZZLE 1 Page 2 of 2

UG45b [in] = Min(UG45b3,UG45b4) #N/A #N/A


UG45b1 [in] = Max(Treq+sca,tUG16(b) + sca) MAX(0+0,0.063 + 0) = 0.063
UG45b2 [in] = 0 0= 0.000
UG45b3 [in] = Max(UG45b1,UG45b2) MAX(0.063,0) = 0.063
UG45b4 [in] = Tstd*0.875 + nca #N/A #N/A
CheckUG45 = UG45 <= Nact #DIV/0! #DIV/0!
#DIV/0!
Minimum thickness per UG-45 [in] = #N/A #N/A

Area Replacement:
Ar [in^2] = 1*d*Treq*1+2*tn*Treq*1*(1-fr1) ~~ required Area
1*0*0*1+2*0*0*1*(1-0) = 0.000
A1 [in^2] = max(d, 2*(nt+tn)) * (E1*nt-1*Treq)-2*tn*(E1*nt-1*Treq)*(1-fr1)
MAX(0, 2*(0+0)) * (0.85*0-1*0)-2*0*(0.85*0-1*0)*(1-0) = 0.000
A2 [in^2] = min((tn-trnR)*fr2*min(5*nt,2*Lp),(tn-trnR)*(Min(2.5*tn+te,2*Lp)*fr2*2))
#DIV/0! #DIV/0!
A3 [in^2] = Min(5*nt*ti*fr2,5*ti*ti*fr2,2*h*ti*fr2)
MIN(5*0*0*0,5*0*0*0,2*0*0*0) = 0.000
A5 [in^2] = (Dp-d-2*tn)*te*fr4 N/A = 0.000
A41 [in^2] = Leg41^2*fr3 0^2*0 = 0.000
A42 [in^2] = Leg42^2*fr4 0^2*1 = 0.000
A43 [in^2] = (Leg43-nca)^2*fr2 (0-0)^2*0 = 0.000
Aa [in^2] = A1+A2+A3+A5+A41+A42+A43 ~~ actual area
#DIV/0! #DIV/0!
CheckA = Aa >= Ar ~~ check area replacement #DIV/0! #DIV/0!

Nozzle Weld Strength: per UW-16(a), (b)


Weld 41 tmin [in] = smaller of 0.75, nt, or Nwall 0.000 0.000 0.000 = 0.0000
Weld 41 Leg [in] = smaller of 0.25 or (tmin * 0.7) / 0.7 0 = 0.0000
0 >= 0 = ERROR
Weld 42 tmin [in] = (smaller of 0.5nt or te) 0.000 = 0.0000
Weld 42 Leg [in] = (smaller of 0.25 or (temin * 0.7) / 0.7) 0 = 0.0000
0 0 >= 0 = N/A
Weld 43 Leg [in] = (smaller of 0.25 or (tmin * 0.7) / 0.7) + sca = 0.0000
0 0 >= 0 = N/A

Cone Required Thickness at Head B Nozzle 1: VIII-1 App 1-4 e)


Treq [in] = P*ODL/(2*COS(a)*(S*E+0.4*P)) + Corr ~~required minimum thickness
#DIV/0! 0.000
O.D. of cone at nozzle: 0 Cone ODL side of nozzle N/A (in)
0.000 Center of nozzle N/A (in)
#VALUE! 0 Cone ODS side of nozzle N/A (in)
Cone straight nozzle: Large nozzle diameter 0.000 (in)
Cone tangent nozzle: Large nozzle diameter 0.000 (in)
Added nozzle cut length: 0.000

Minimum design temperature check: Impact testing exempt to -20F per UG20(f)
UCS-66 CURVE 'B' RATING [F]: #N/A

Nozzle Weld Strength: per UW-16(i) (using Weld 41 only)

Weld 41 + Weld 43 tmin [in] = smaller of 1.25 * nt, or Nwall (0.25" min)
0.000 0 * 1.25 = 0.0000
0+0 >= 0 = Acceptable
0 >= 0.25 = ERROR
(using Weld 41 only)
0 #N/A #N/A #N/A #N/A #N/A
Calculated nozzle weight (LBS): 0.00 #N/A #N/A #N/A #N/A #N/A
YOUR COMPANY NAME
CALCULATIONS FOR ASME CODE SECTION VIII, DIVISION I, 2017 EDITION
PRESSURE VESSEL CALCULATIONS
WORKBOOK VERSION: 09222018b

Head Nozzle and Repad (Not Required) 10/24/2018 Page 1 of 2


HEAD B NOZZLE 2 -- NOT USED NOZZLE ID. 0 INCH/PSI OTHER
JOB NO: 0 QTY= 0 FLANGE/COUPLING RATING 3,500 PSI
Head Inputs: HEAD B (END) ELLIPTICAL (Nozzles within 80% limit only)
SA-36 Material
16,600 Sv [psi] - allowable stress
0.85 E1 - efficiency of head at nozzle
0.000 Ds [in] - inside head dish diameter
0.000 nt [in] - nominal head wall thickness
0.000 Treq [in] - required head wall thickness
0.000 sca [in] - shell/head corrosion allowance
0.063 tUG16(b) [in] - minimum thickness per UG-16 b
Nozzle Inputs: ERROR
INHERENT Material
0 Sn [psi] - allowable stress
1.00 E - nozzle efficiency
0.000 Do [in] - outside diameter of nozzle
0.000 Nwall [in] - nominal wall thickness of nozzle
0.000 Lp [in] - exterior projection of nozzle
0.000 Ip [in] - interior projection of nozzle
0.000 nca [in] - nozzle corrosion allowance
0.0% UTP [%] - undertolerance allowance
0.0 Pn [psi] - interior pressure

Reinforcement:
INHERENT Material
16,600 Sp [psi] - allowable stress of repad
0.0000 te [in] - repad thickness 0.000
0.000 Dp [in] - outside diameter
0.000 Leg41 [in] - fillet size
0.000 Leg42 [in] - fillet size
0.000 Leg43 [in] - fillet size
0.000 LegG [in] - depth of groove
Variables:
UT [in] = Nwall*UTP 0*0 = 0.000
Rn [in] = Do/2 - (Nwall-nca) + UT 0/2 - (0-0) + 0 = 0.000
ti [in] = Nwall-2*nca 0-2*0 = 0.000
h [in] = MIN(Ip-sca,2.5*nt,2.5*ti) MIN(0-0,2.5*0,2.5*0) = 0.000
tn [in] = Nwall-nca 0-0 = 0.000
d [in] = Do-2*tn 0-2*0 = 0.000
fr1 = MIN(Sn/Sv,1) MIN(0/16600,1) = 0.000
fr2 = MIN(Sn/Sv,1) MIN(0/16600,1) = 0.000
fr3 = MIN(Sn/Sv,Sp/Sv,1) MIN(0/16600,16600/16600,1) = 0.000
fr4 = MIN(Sp/Sv,1) MIN(16600/16600,1) = 1.000
Required Thickness: UG-27(c)(1,2)
TreqN [in] = (Pn*Rn)/(Sn*E - 0.6*Pn)+nca ~~ required minimum thickness
(0*0)/(0*1 - 0.6*0)+0 = #DIV/0!
trnR [in] = (Pn*Rn)/(Sn*1 - 0.6*Pn) (0*0)/(0*1 - 0.6*0) = #DIV/0!
CheckTreqN = TreqN <= Nwall #DIV/0! #DIV/0!
UG-45:
Tstd [in] = thickness standthickness standard wall pipe VLOOKUP(0,PIpeWall,2) = #N/A
Nact [in] = Nwall * (1-UTP) 0 * (1-0) = 0.000
UG45 [in] = Max(UG45a, UG45b) ~~ required thickness per UG-45 #DIV/0! #DIV/0!
UG45a [in] = trnR + nca #DIV/0! #DIV/0!
UG45b [in] = Min(UG45b3,UG45b4) #N/A #N/A

HEAD B NOZZLE 2 Page 2 of 2

UG45b1 [in] = Max(Treq+sca,tUG16(b) + sca) MAX(0+0,0.063 + 0) = 0.063


UG45b2 [in] = 0 0= 0.000
UG45b3 [in] = Max(UG45b1,UG45b2) MAX(0.063,0) = 0.063
UG45b4 [in] = Tstd*0.875 + nca #N/A #N/A
CheckUG45 = UG45 <= Nact #DIV/0! #DIV/0!
#DIV/0!
Minimum thickness per UG-45 [in] = #N/A #N/A

Area Replacement:
Ar [in^2] = 1*d*Treq*1+2*tn*Treq*1*(1-fr1) ~~ required Area
1*0*0*1+2*0*0*1*(1-0) = 0.000
A1 [in^2] = max(d, 2*(nt+tn)) * (E1*nt-1*Treq)-2*tn*(E1*nt-1*Treq)*(1-fr1)
MAX(0, 2*(0+0)) * (0.85*0-1*0)-2*0*(0.85*0-1*0)*(1-0) = 0.000
A2 [in^2] = min((tn-trnR)*fr2*min(5*nt,2*Lp),(tn-trnR)*(Min(2.5*tn+te,2*Lp)*fr2*2))
#DIV/0! #DIV/0!
A3 [in^2] = Min(5*nt*ti*fr2,5*ti*ti*fr2,2*h*ti*fr2)
MIN(5*0*0*0,5*0*0*0,2*0*0*0) = 0.000
A5 [in^2] = (Dp-d-2*tn)*te*fr4 N/A = 0.000
A41 [in^2] = Leg41^2*fr3 0^2*0 = 0.000
A42 [in^2] = Leg42^2*fr4 0^2*1 = 0.000
A43 [in^2] = (Leg43-nca)^2*fr2 (0-0)^2*0 = 0.000
Aa [in^2] = A1+A2+A3+A5+A41+A42+A43 ~~ actual area
#DIV/0! #DIV/0!
CheckA = Aa >= Ar ~~ check area replacement #DIV/0! #DIV/0!

Nozzle Weld Strength: per UW-16(a), (b)


Weld 41 tmin [in] = smaller of 0.75, nt, or Nwall 0.000 0.000 0.000 = 0.0000
Weld 41 Leg [in] = smaller of 0.25 or (tmin * 0.7) / 0.7 0 = 0.0000
0 >= 0 = ERROR
Weld 42 tmin [in] = (smaller of 0.5nt or te) 0.000 = 0.0000
Weld 42 Leg [in] = (smaller of 0.25 or (temin * 0.7) / 0.7) 0 = 0.0000
0 0 >= 0 = N/A
Weld 43 Leg [in] = (smaller of 0.25 or (tmin * 0.7) / 0.7) + sca = 0.0000
0 0 >= 0 = N/A

Minimum design temperature check: Impact testing exempt to -20F per UG20(f)
UCS-66 CURVE 'B' RATING [F]: #N/A

Weld 41 + Weld 43 tmin [in] = smaller of 1.25 * nt, or Nwall (0.25" min)
0.000 0 * 1.25 = 0.0000
0+0 >= 0 = Acceptable
0 >= 0.25 = ERROR
(using Weld 41 only)
0 #N/A #N/A #N/A #N/A #N/A
Calculated nozzle weight (LBS): 0.00 #N/A #N/A #N/A #N/A #N/A
Nozzle & Flange overide weight (LBS): 0.00
Note: Attached piping to be externally supported. Calculations are limited to materials listed in this sheet.
YOUR COMPANY NAME
CALCULATIONS FOR ASME CODE SECTION VIII, DIVISION I, 2017 EDITION
PRESSURE VESSEL CALCULATIONS
WORKBOOK VERSION: 09222018b Page 1 of 1
10/24/2018
Conical Section per Appendix 1-5 0.000 Page
JOB NO: 0
Dimensions:
0.000 ODL [in] - outside diameter of large end
0.000 IDL [in] - inside diameter of large end
0.000 ODS [in] - outside diameter of small end
0.000 IDS [in] - inside diameter of small end
0.000 t [in] - thickness
0.000 L [in] -length #DIV/0! 0.000
0.000 Corr [in] - corrosion allowance
Material and Conditions:
INHERENT Material
#N/A S [psi] - allowable stress
E - long seam efficiency = 85%
0.0 P [psi] - interior pressure
Calculated Properties: 0.000
Approx. cone weight based on steel, lbs = 0.0
Approx. cone volume , cuft = 0.00
a [rad] = ATAN((ODL-ODS)/(2*L)) ~~ alpha angle in radians ATAN((0-0)/(2*0)) = #DIV/0!
angle [deg] = Degrees(a) ~~ alpha angle in degrees #DIV/0! #DIV/0!
nt [in] = t-Corr ~~ thickness with corrosion allowance removed 0-0 = 0.000
Required Thickness: VIII-1 App 1-4 e)
Treq [in] = P*ODL/(2*COS(a)*(S*E+0.4*P)) + Corr ~~required minimum thickness
#DIV/0! #DIV/0!
CheckTreq = Treq <= t #DIV/0! #DIV/0!
Maximum Pressure: VIII-1 App 1-4(e)
Pmax [psi] = 2*S*E*nt*cos(a)/(ODL-0.8*nt*cos(a)) ~~maximum allowed design pressure
#N/A #N/A
CheckPMax = Pmax >= P #N/A #N/A

Minimum design temperature check: Impact testing exempt to -20F per UG20(f)
UCS-66 CURVE 'B' RATING [F]: #N/A / 'D' [F]: #N/A
All UG-16 minimum thickness requirements have not been taken into consideration here.
YOUR COMPANY NAME
CALCULATIONS FOR ASME CODE SECTION VIII, DIVISION I, 2017 EDITION
PRESSURE VESSEL CALCULATIONS
WORKBOOK VERSION: 09222018b
Page 1 of 1
HEAD ON BOOT 2:1 RATIO ELLIPTICAL Page 10/24/2018

JOB NO. 0
Dimensions:
0.000 Do [in] - outside diameter of head
0.000 Di [in] - inside diameter of head
0 t [in] - nominal wall thickness t= 0.000
0.000 tf [in] - thickness after forming (note 1)
0.000 Corr [in] - corrosion allowance
0.000 Skirt [in] - straight skirt length
Material and Conditions:
INHERENT Material
#N/A S [psi] - allowable stress
0.0% UTP [%] - undertolerance allowance
E - head/shell joint efficiency 85%
0.0 P [psi] - interior pressure 0.000
Calculated Properties: #N/A
note 1: Suggested thickness after forming Approx. head weight based on steel, lbs = 0.00
-0.0625 in Approx. head volume including skirt, cuft = 0.00
Variables:
ut [in] = tf*UTP ~~ undertorlerance allowance 0*0 = 0.000
nt [in] = tf-(Corr+ut) ~~ thickness with corrosion allowance removed 0-0+0 = 0.000
D [in] = Do-2*nt ~ ID with corrosion allowance removed 0+2*0-(0*2) = 0.000
h [in] = D/4 ~~ inside crown height 0/4 = 0.000
ho [in] = h+nt 0+0 = 0.000
D/2h = D/(2*h) 0/(2*0) = #DIV/0!
Do/2ho = Do/(2*ho) 0+(0*2)/(2*0) = #DIV/0!
K = #DIV/0! Interpolated value from table 1-4.1 1= #DIV/0!
Kone = #DIV/0! Interpolated value from table UG-37 0.9 = #DIV/0!
Kzero = #DIV/0! Interpolated value from table UG-33.1 0.889 = #DIV/0!
Ro [in]= Kzero*Do #DIV/0! #DIV/0!
Required Thickness: App. 1-4(c), UG-37(a)(1)
App1-4(f) = tf/(Kone*D) #DIV/0! #DIV/0!
#DIV/0!
Treq [in] = (P*D*K)/(2*S*E-0.2*P)+Corr ~~ required minimum thickness
#DIV/0! #DIV/0!
CheckTreq = Treq<=tf #DIV/0! #DIV/0!
Check UG-16(b) = nt >= 0.0625+Corr 0 >= 0.0625 = ERROR

Maximum Pressure: App. 1-4(c), UG-37(a)(1)


Pmax [psi] = (2*S*E*nt)/(K*D+0.2*nt) ~~ maximum allowed design pressure
#N/A #N/A
CheckPMax = Pmax >= P #N/A #N/A
Minimum design temperature check: Impact testing exempt to -20F per UG20(f)
UCS-66 CURVE 'B' RATING [F]: #N/A / 'D' [F]: #N/A
All UG-16(b) minimum thickness requirements have not been taken into consideration here.
Nozzles may be subject to a smaller required thickness depending on location in the head.
Heads may be subject to stress relief if large elongation occurs - UCS-79(d), UNF-79(d), UHA-44(d)
YOUR COMPANY NAME
CALCULATIONS FOR ASME CODE SECTION VIII, DIVISION I, 2017 EDITION
PRESSURE VESSEL CALCULATIONS
SPREADSHEET VERSION: 08092015
Page 1 of 1
Bolted Closure Formed 2:1 Elliptical head used 10/24/2018

JOB NO. 0
Dimensions: Closure on shell or nozzle
Do [in] - outside diameter of closure head = 0.00
0.000 Di [in] - inside diameter of closure head
0 t [in] - nominal wall thickness 0.000
0.000 tf [in] - thickness after forming (note 1)
0.000 Corr [in] - corrosion allowance
0.000 Skirt [in] - straight skirt length
Material and Conditions:
SA-516 70 Material SA-516 70 used
20,000 S [psi] - allowable stress
0.0% UTP [%] - undertolerance allowance
0.85 E - head/shell joint efficiency
0.0 P [psi] - interior pressure
Calculated Properties:
note 1: Suggested thickness after forming Approx. head weight based on steel, lbs = 0.00
-0.0625 in Approx. head volume including skirt, cuft = 0.00
Variables:
ut [in] = tf*UTP ~~ undertorlerance allowance 0*0 = 0.000
nt [in] = tf-(Corr+ut) ~~ thickness with corrosion allowance removed 0-0+0 = 0.000
D [in] = Do-2*nt ~ ID with corrosion allowance removed 0+2*0-(0*2) = 0.000
h [in] = D/4 ~~ inside crown height 0/4 = 0.000
ho [in] = h+nt 0+0 = 0.000
D/2h = D/(2*h) 0/(2*0) = #DIV/0!
Do/2ho = Do/(2*ho) 0+(0*2)/(2*0) = #DIV/0!
K = #DIV/0! Interpolated value from table 1-4.1 1= #DIV/0!
Kone = #DIV/0! Interpolated value from table UG-37 0.9 = #DIV/0!
Kzero = #DIV/0! Interpolated value from table UG-33.1 0.889 = #DIV/0!
Ro [in]= Kzero*Do #DIV/0! #DIV/0!
Required Thickness: App. 1-4(c), UG-37(a)(1)
App1-4(f) = tf/(Kone*D) #DIV/0! #DIV/0!
#DIV/0!
Treq [in] = (P*D*K)/(2*S*E-0.2*P)+Corr ~~ required minimum thickness
#DIV/0! #DIV/0!
CheckTreq = Treq<=tf #DIV/0! #DIV/0!
Check UG-16(b) = nt >= 0.0625+Corr 0 >= 0.0625 = ERROR

Maximum Pressure: App. 1-4(c), UG-37(a)(1)


Pmax [psi] = (2*S*E*nt)/(K*D+0.2*nt) ~~ maximum allowed design pressure
#DIV/0! #DIV/0!
CheckPMax = Pmax >= P #DIV/0! #DIV/0!

Calculations for swing bolted heads:


INHERENT Flange or ring Material
#N/A S [psi] - allowable stress
0.000 Ft [in] - flange or ring thickness #N/A
0.000 Bc [in] - bolt circle centerline diameter PRESSUR LOADING
0.000 B [in] - bolt diameter (0.5" to 2.5" max.)
SA-193 B7 Bm - bolt material
25,000 Bs (psi) - bolt allowable stress value
#N/A Bl [in] - bolt loading #N/A 0 #N/A
#N/A Bt (ft/lbs) - bolt torque
0 Bn - number of bolts used #N/A
0.000 Gc [in] - gasket centerline diameter (d) hg = 0.000
0.000 Lw [in] - Lug width at hole (w)
0.000 Lt [in] - Lug thickness Weight = 0.00 lbs
INHERENT Lug material #N/A #N/A
#N/A Ls (psi) - Lug allowable stress value
1.00 E - efficiency if joint present
Thickness required for flat circular bolted heads or rings using C = 0.3
t = [d * square root {(CP/SE)+(1.9Whg/SEd3)}]+Corr #N/A (in)
Required clamping force (LB)= (Gc/2)*(Gc/2)*(22/7)*P= 0
Bolt clamping force (LB)= Bn*Bl= #N/A #N/A
Required lug thickness (in) = Bl/(2Ls(Lw-B)) = #N/A (in)
Maximum lug load (LB)= Bl*(Lt/Rt) #N/A
#N/A #N/A
Minimum design temperature check: Impact testing exempt to -20F per UG20(f)
UCS-66 CURVE 'B' RATING [F]: #N/A / 'D' [F]: #N/A

Appendix FF must be considered for Quick-Opening and Quick-Actuating Closures per UG-35.2
YOUR COMPANY NAME
CALCULATIONS FOR ASME CODE SECTION VIII, DIVISION I, 2017 EDITION
PRESSURE VESSEL CALCULATIONS
WORKBOOK VERSION: 09222018b Page 1 of 1

Circular Unstayed Flat Head per UG-34 10/24/2018 1 of 1


Figure UG-34 sketch (e) and others
JOB NO: 0
Dimensions:
SHELL #1 d [in] - inside diameter 0.000
0.000 ts [in] - shell nominal wall thickness
#N/A tr [in] - required shell thickness
85% E - joint efficiency
0.000 Corr [in] - corrosion allowance
Material and Conditions:
* SA-105 Head or Flange Material
20,000 S [psi] - allowable stress
* 0.000 t [in] - head nominal thickness
0.00 P [psi] - interior pressure

Calculations for sketches (b-2), (e), (f), (g), (i): 0.00 lbs (weight)
Thickness required for flat unstayed circular heads using C = #N/A #N/A
tr = [d * square root (CP/SE)] + Corr tr = #N/A in
Maximum allowable design pressure= P*(t/tr) = #N/A psi
Minimum design temperature:
UCS-66 CURVE "B" CURVE "D"
#N/A #N/A #N/A #N/A
Calculations for sketches (h), (r), (s):
Thickness required for flat unstayed circular heads using C = 0.33
tr = [d * square root (CP/SE)] + Corr tr = 0.00 in
Maximum allowable design pressure= P*(t/tr) = #DIV/0! psi
Minimum design temperature:
UCS-66 CURVE "B" CURVE "D"
#DIV/0! #DIV/0!

Fabricated Bolted Flanged Heads or Blind Flange


(Self energizing seals only)

* 0.000 D [in] - flange/head outside diameter


* 0.000 t [in] - flange/head nominal thickness #DIV/0!
* 0.000 Bc [in] - bolt circle centerline diameter PRESSURE LOADING
* 0.000 B [in] - bolt diameter (0.5" to 2.5" max.)
* SA-193 B7 Bm - bolt material
25,000 Bs (psi) - bolt allowable stress value
#N/A Bl [in] - bolt loading
#N/A Bt (ft/lbs) - bolt torque
* 0 Bn - number of bolts used
* 0.000 Go (in.) - gasket or o-ring O.D.
* 0.000 Gi (in.) - gasket or o-ring I.D.
0.000 Gc [in] - gasket centerline diameter (d) hg = 0.000
Thickness required for flat unstayed circular bolted heads using C = 0.3 0.0000 #DIV/0!
tr = [d * square root {(CP/SE)+(1.9Whg/SEd3)}]+Corr tr = #DIV/0! in
Required clamping force (LB)= (Gc/2)*(Gc/2)*(22/7)*P= 0
Bolt clamping force (LB)= Bn*Bl= #N/A #N/A
Thickness maximum allowable design pressure= P*(t/tr) = #DIV/0! psi
Bolt clamping force maximum allowable pressure= #N/A
0 Weight= 0.00 lbs
Minimum design temperature:
UCS-66 CURVE "B" CURVE "D"
#DIV/0! #DIV/0! #N/A #N/A

* Requires input

B16.5 FLANGE
No. HOLES HOLE
RATING TYPE SIZE MATERIAL WEIGHT THICKNESS PSI HOLE I.D. CIRCLE
NONE NONE 0 NONE 0 0 0 0 0
YOUR COMPANY NAME
CALCULATIONS FOR ASME CODE SECTION VIII, DIVISION I, 2017 EDITION
PRESSURE VESSEL CALCULATIONS
WORKBOOK VERSION: 09222018b Page 1 of 1
10/24/2018
Straight Pipe or Shell under external pressure
UG-28 Calculations 0 Rings required
JOB NO: 0
Dimensions:
0.000 Di [in] - inside diameter
Do
0.000 Do [in] - outside diameter
0.000 ts [in] - nominal wall thickness less UTP
0.000 t [in] - corroded wall thickness t
* 0.000 L [in] -length of section
0.000 Corr [in] - corrosion allowance
Material and Conditions:
INHERENT Material

Length
#N/A S [psi] - allowable stress

Long Seam
* 29,000,000 E - modulus of elasticity
0.85 El - long seam efficiency (circ stress)
0.85 Ec - circ seam efficiency (long stress)
12.5% UTP [%] - undertolerance allowance
0.0 P [psi] - interior pressure
* 15.0 Px [psi] - external pressure

Inputs from Charts: (where Do/t > 10)


* 0.000124 A - from Figure G below using Do/ts = #DIV/0! L/Do= #DIV/0!
* 3,625 B - from Figure CS-2 below

Calculations: (where Do/t > 10)


Pa (External Allowable pressure) for A value left of line:
Acceptable At shell corroded condition: N/A psi
Pa (External Allowable pressure) for A value right of line:
#DIV/0! At shell corroded condition: #DIV/0! psi

Inputs from Charts: (where Do/t < 10)


* 3,625 B - from Figure CS-2 below using A value: #DIV/0!

Calculations: (where Do/t < 10)


Pa (External Allowable pressure) #REF! #REF! #DIV/0! #DIV/0!
#DIV/0! At shell nominal thickness less CA: #DIV/0! psi #DIV/0!
* Requires change or input
YOUR COMPANY NAME Page 1 of 1
TOWER/ANCHOR BOLT/LIFTING LUG DESIGN CALCULATIONS

CUSTOMER: YOUR COMPANY NAME JOB#: 0 10/24/2018

SKIRT MATERIAL SA­36 (Select below)


SKIRT O.D. 0 Increase
SKIRT HEIGHT 0 Increase
SKIRT THICKNESS 0 #VALUE!
BASE PLATE O.D. 0 Increase
BASE PLAT THICKNESS 0 #VALUE!

DESIGN INPUTS CALCULATION OUTPUTS
TOTAL REQ, SHELL THICKNESS #N/A
VESSEL O.D.(IN.): 0 VESSEL SHELL WEIGHT DRY: 0
SHELL HEIGHT (IN.): 0 VESSEL SHELL WEIGHT WET: 0
SHELL WALL THICKNESS: 0 MAWP MIN. THICKNESS LS: #N/A
CORROSION ALLOWANCE: 0 WIND/MAWP REQ. THICKNESS: #N/A
SHELL STRESS VALUE: #N/A SKIRT WIND+WEIGHT REQ.TK: #VALUE!
JOINT EFFICIENCY: 0.85 BOLT LOAD (WIND+WEIGHT): #VALUE!
SKIRT O.D. (IN.): 0.000 BASE RING REQ. TKNESS: #DIV/0!
SKIRT HEIGHT (IN.): 0.000 LIFTING LUG REQ.TKNESS: #N/A
SKIRT THICKNESS: #VALUE! FILLET WELD REQ.TKNESS: #DIV/0!
BASE RING O.D.: 6.000 MAX.FILLET WELD LOAD: #N/A
BASE RING I.D.: ­3.000 MAX.LIFTING LUG LOAD: #N/A
CORROSION ALLOWANCE: 0 DEFLECTION AT TOP (IN.): #VALUE!
SKIRT MATERIAL: SA­36 MAX.ALLOWABLE DEFLECTION: 0.000 
INSULATION THICKNESS: ______ VIBRATION PERIOD (SEC.) #DIV/0!
INTERNAL WEIGHT: 0 MAX.ALLOWABLE VIB.PERIOD: #DIV/0!
BOLT SIZE 0.500 SEISMIC SHEAR AT BASE: #DIV/0!
BOLT ROOT AREA 0.126 SEISMIC MOMENT AT BASE: #DIV/0!
NUMBER OF BOLTS 0 BUCKLING SKIRT/SHELL #N/A
BOLT CIRCLE (IN.) 0.00 INCREASE 16,600
INTERNAL DESIGN MAWP: 0
WIND FORCE (PSF): 0 CALCULATIONS ARE BASED ON FORMULAS 
SIESMIC ZONE FACTOR: 0.1875 FROM THE ELEVENTH EDITION OF THE
HEIGHT COEFFICIENT: 1 PRESSURE VESSEL HANDBOOK
SITE COEFFICIENT: 1
LIFTING LUG HOLE: 0
LUG CROWN RADIUS: 0
LUG BASE LENGTH: 0
LUG THICKNESS: #N/A
LUG STRESS VALUE: #N/A
FILLET WELD LEG: #N/A
HORIZONTAL VESSEL WITH TWO SADDLE DESIGN
VESSEL CALCULATED WEIGHT 0 LBS (FLOODED)
ADDED WEIGHT 0 LBS
VESSEL DIAMETER 0 INCH TYP = 4 TYP = 0.25
Rm VESSEL I.D. RADIUS 0 INCH
L VESSEL S/S LENGTH 0 INCH SA-36 Y
VESSEL THICKNESS 0 INCH 0 N M1 LS1 Mt Mc #DIV/0! STIFF MOMENT
DESIGN PRESSURE 0 PSI SA-36 #DIV/0! #DIV/0! #DIV/0! #DIV/0! 0 0
H HEAD DEPTH 2.03 INCH SA-516 70 #DIV/0! LS2 0 0
SHELL/HEAD STRESS #N/A PSI SA-240 304 #DIV/0! #DIV/0! WEB A1= 0
SADDLE MATERIAL SA-36 SA-240 316 #DIV/0! A2= 0
SADDLE STRESS 16,600 PSI M2 LS3
F=Q SADDLE LOAD (EACH) 0 LBS #DIV/0! #DIV/0! Y1= 0
A SADDLE DIST. FROM HEAD 0 INCH #DIV/0! LS4 Y2= 0
b SADDLE WIDTH 0 INCH TYP = 4 #DIV/0! #DIV/0! AY= 0
SADDLE BEARING ANGLE 120 DEGREES #DIV/0! C= #DIV/0!
SADDLE RIB THICKNESS 0.00 INCH TYP = 0.25 H1= #DIV/0! #DIV/0!
SADDLE WEB THICKNESS 0.00 INCH INCREASE H2= #DIV/0! #DIV/0!
BASE PLATE THICKNESS 0.00 INCH INCREASE AH= #DIV/0!
WEAR PLATE THICKNESS 0.00 INCH I= #DIV/0!
WEAR PLATE WIDTH 0.00 INCH 0 0 0
SADDLE HEIGHT 0.00 INCH
M1 # RINGS @ PER SADDLE 0 0 1 2
M2 MOMENT @ SADDLE #DIV/0! #DIV/0!
T MOMENT @ VESSEL CENTER #DIV/0! #DIV/0! To improve number in the green blocks, try increasing angle, saddle width, or moving saddles.
LS1 SHEAR FORCE @ SADDLE 0 Adding wear plates or increasing their thickness will help.
LS2 LONGITUDINAL STRESS 1 #DIV/0! #DIV/0! Stiffener rings will help with shell loading at the saddle.
LS3 LONGITUDINAL STRESS 2 #DIV/0! #DIV/0!
LS4 LONGITUDINAL STRESS 3 #DIV/0! #DIV/0! Note: Wind, seismic, and internal design pressure are not considered in this sheet. Saddle load
LONGITUDINAL STRESS 4 #DIV/0! #DIV/0! is based on vessel flooded weight. Unprotect sheet to change loading.
A:R
SADDLE DIST : RADIUS RATIO #DIV/0! SADDLE DISTANCE CHANGE PER DEGREE (F) RISE OR FALL= 0.00 INCH
VALUE OF CONSTANT K1 0.3350 CHANGE 100 F
VALUE OF CONSTANT K2 1.1710 DISTANCE 0.00 INCH
VALUE OF CONSTANT K3 0.3190
VALUE OF CONSTANT K4 0.8800
VALUE OF CONSTANT K5 0.4010
VALUE OF CONSTANT K6 #DIV/0!
VALUE OF CONSTANT K7 0.7600
VALUE OF CONSTANT K8 0.6030
VALUE OF CONSTANT K9 0.3400
VALUE OF CONSTANT K10 0.0530
VALUE OF CONSTANT K11 0.2040

LONGITUDINAL BENDING
BENDING @ SADDLE TENSION #DIV/0!
BENDING @ SADDLE COMPRESSION #DIV/0!
Mt BENDING @ MIDSPAN TENSION #DIV/0!
Mc BENDING @ MIDSPAN COMPRESSION #DIV/0! #DIV/0!

TANGENTIAL SHEAR
IN SHELL N/A
IN SHELL N/A
IN SHELL & HEAD #DIV/0! #DIV/0!
IN SHELL & HEAD ADDITIONAL STRESS #DIV/0! #DIV/0!

CIRCUMFERENTIAL SHEAR STIFFENED


AT HORN (UNSTIFFENED) #DIV/0! #DIV/0! #DIV/0! #DIV/0!
AT HORN (UNSTIFFENED) N/A N/A
AT BOTTOM OF SHELL #DIV/0! #N/A 0 0 #DIV/0!
0 #DIV/0!
STIFFENER THICKNESS 0
STIFFENER HEIGHT 0

STIFFENING RING INSIDE @ SHELL N/A #DIV/0!


STIFFENING RING OUTSIDE @ SHELL N/A
STIFFENING RING OUTSIDE @ TIP N/A #DIV/0! 0
Nozzle Loads WRC 107 24-Oct-18 Page 1 of 1

JOB NO. 0
NOZZLE #N/A
#N/A
T
Inputs:
#N/A <- Shell Midline Radius (Rm)
#N/A <- Nozzle Outside Diameter #NAME?
#N/A <- Shell Thickness (T)
0 <- F (Load, lbs) #NAME?

M rlm

F
0 <- Mc (load on flange, lbs)

R o
0 <- Ml (load on flange, lbs) #N/A
#N/A <- Nd (nozzle projection, in.)

M rc m
0 <- P (pressure, psi)
#N/A <- Sy (Yield strength) #NAME?
#N/A <- Sa (Allowable Stress)
#N/A <- RePad thickness R M
0 <- Corrosion Allowance
#N/A
Constants: Nozzle inherent weight = #N/A (lbs)
Beta = 0.875(Ro/Rm) = #NAME?
Gamma = Rm/T = #NAME?
Alpha (Interpolated) = #NAME?
Sigma (Interpolated) = #NAME?
Delta (Interpolated) = #NAME?
Calculated stress = (2P/t)*(Rm-T/2) = #NAME? = #NAME?
Max stress = Sa = #NAME?

Maximum Allowed Loads (uncombined):


end load Fmax = (Rm^2/alpha)*(Sy-Stress)
= #NAME?
= #NAME? lbs (Allowed at Mc and Ml = 0)

Moment c Mrcm = (Rm^2*Ro*Sy)/(Sigma)


= #NAME?
= #NAME? in.lbs (Allowed at Fmax and Ml = 0)

Moment l Mrlm = (Rm^2*Ro/Delta)*(Sy-Stress)


= #NAME?
= #NAME? in.lbs (Allowed at Fmax and Mc = 0)

Combined Loads:

F/Fmax = #NAME? F/Fmax = #NAME?


Mc/Mrcm = #NAME? Mc/Mrcm = #NAME?
Ml/Mrlm = #NAME? Mc/Mrcm = #NAME?

Total Load = #NAME?


= #NAME?
#NAME? #NAME?
150 LB. FLANGES - INCHES 150#
Nom. Y No. & WNFLG.
Pipe O C Weld Slip on Lap Bolt Size of Wt.
Size INCHES INCHES Neck Thrd. Joint Circle Holes Lbs
1/ 2 3 1/ 2 7/16 1 7/8 5/8 5/ 8 2 3/ 8 4 - 5/8 2
3/ 4 3 7/ 8 1/ 2 2 1/16 5/ 8 5/ 8 2 3/ 4 4 - 5/8 2
1 4 1/ 4 9/16 2 3/16 11/16 11/16 3 1/ 8 4 - 5/8 2.5
1 1/4 4 5/ 8 5/ 8 2 1/4 13/16 13/16 3 1/ 2 4 - 5/8 2.5
1 1/2 5 11/16 2 7/16 7/ 8 7/ 8 3 7/ 8 4 - 5/8 4
2 6 3/ 4 2 1/2 1 1 4 3/ 4 4-3/4 6
2 1/2 7 7/ 8 2 3/4 1 1/ 8 1 1/ 8 5 1/ 2 4-3/4 10
3 7 1/ 2 15/16 2 3/4 1 3/16 1 3/16 6 4-3/4 11.5
4 9 15/16 3 1 5/16 1 5/16 7 1/ 2 8-3/4 16.5
5 10 15/16 3 1/2 1 7/16 1 7/16 8 1/ 2 8-7/8 21
6 11 1 3 1/2 1 9/16 1 9/16 9 1/ 2 8-7/8 26
8 13 1/ 2 1 1/ 8 4 1 3/ 4 1 3/ 4 11 3/ 4 8-7/8 42
10 16 1 3/16 4 1 15/16 1 15/16 14 1/ 4 12-1 54
12 19 1 1/ 4 4 1/2 2 3/16 2 3/16 17 12-1 88
14 21 1 3/ 8 5 2 1/ 4 3 1/ 8 18 3/ 4 12-1 1/8 114
16 23 1/ 2 1 7/16 5 2 1/ 2 3 7/16 21 1/ 4 16-1 1/8 142
18 25 1 9/16 5 1/2 2 11/16 3 13/16 22 3/ 4 16-1 1/4 165
20 27 1/ 2 1 11/16 5 11/16 2 7/ 8 4 1/16 25 20-1 1/4 197
24 32 1 7/ 8 6 3 1/ 4 4 3/ 8 29 1/ 2 20-1 3/8 268

300 LB. FLANGES - INCHES 300#


Nom. Y No. & WNFLG.
Pipe O C Weld Slip on Lap Bolt Size of Wt.
Size INCHES INCHES Neck Thrd. Joint Circle Holes Lbs
1/ 2 3 3/ 4 9/16 2 1/16 7/ 8 7/ 8 2 5/ 8 4 - 5/8 2
3/ 4 4 5/ 8 5/ 8 2 1/ 4 1 1 3 1/ 4 4 - 3/4 3
1 4 7/ 8 11/16 2 7/16 1 1/16 1 1/16 3 1/ 2 4 - 3/4 4
1 1/4 5 1/ 4 3/ 4 2 9/16 1 1/16 1 1/16 3 7/ 8 4 - 3/4 5
1 1/2 6 1/ 8 13/16 2 11/16 1 3/16 1 3/16 4 1/ 2 4 -7/8 7
2 6 1/ 2 7/ 8 2 3/ 4 1 5/16 1 5/16 5 8-3/4 8
2 1/2 7 1/ 2 1 3 1 1/ 2 1 1/ 2 5 7/ 8 8-7/8 12
3 8 1/ 4 1 1/ 8 3 1/ 8 1 11/16 1 11/16 6 5/ 8 8-7/8 18
4 10 1 1/ 4 3 3/ 8 1 7/ 8 1 7/ 8 7 7/ 8 8-7/8 26.5
5 11 1 3/ 8 3 7/ 8 2 2 9 1/ 4 8-7/8 36
6 12 1/ 2 1 7/16 3 7/ 8 2 1/16 2 1/16 10 5/ 8 12-7/8 45
8 15 1 5/ 8 4 3/ 8 2 7/16 2 7/16 13 12-1 69
10 17 1/ 2 1 7/ 8 4 5/ 8 2 5/ 8 3 3/ 4 15 1/ 4 16-1 1/8 100
12 20 1/ 2 2 5 1/ 8 2 7/ 8 4 17 3/ 4 16-1 1/4 142
14 23 2 1/ 8 5 5/ 8 3 4 3/ 8 20 1/ 4 20-1 1/4 206
16 25 1/ 2 2 1/ 4 5 3/ 4 3 1/ 4 4 3/ 4 22 1/ 2 20-1 3/8 249
18 28 2 3/ 8 6 1/ 4 3 1/ 2 5 1/ 8 24 3/ 4 24-1 3/8 306
20 30 1/ 2 2 1/ 2 6 3/ 8 3 3/ 4 5 1/ 2 27 24-1 3/8 369
24 36 2 3/ 4 6 5/ 8 4 3/16 6 32 24-1 5/8 519

** The 1/4" raised face is not included in the thickness "Y" or "C"
400 LB. FLANGES - INCHES 400 #
Nom. **Y (See Note Above) No. & WNFLG.
Pipe O C Weld Slip on Lap Bolt Size of Wt.
Size INCHES INCHES Neck Thrd. Joint Circle Holes Lbs
1/ 2 3 3/ 4 9/16 2 1/16 7/ 8 7/ 8 2 5/ 8 4 - 5/8 3
3/ 4 4 5/ 8 5/ 8 2 1/ 4 1 1 3 1/ 4 4 - 3/4 3.5
1 4 7/ 8 11/16 2 7/16 1 1/16 1 1/16 3 1/ 2 4 - 3/4 4
1 1/4 5 1/ 4 13/16 2 5/ 8 1 1/ 8 1 1/ 8 3 7/ 8 4 - 3/4 5.5
1 1/2 6 1/ 8 7/ 8 2 3/ 4 1 1/ 4 1 1/ 4 4 1/ 2 4 -7/8 8
2 6 1/ 2 1 2 7/ 8 1 7/16 1 7/16 5 8-3/4 10
2 1/2 7 1/ 2 1 1/ 8 3 1/ 8 1 5/ 8 1 5/ 8 5 7/ 8 8-7/8 14
3 8 1/ 4 1 1/ 4 3 1/ 4 1 13/16 1 13/16 6 5/ 8 8-7/8 18
4 10 1 3/ 8 3 1/ 2 2 2 7 7/ 8 8-1 30
5 11 1 1/ 2 4 2 1/ 8 2 1/ 8 9 1/ 4 8-1 39
6 12 1/ 2 1 5/ 8 4 1/16 2 1/ 4 2 1/ 4 10 5/ 8 12-1 49
8 15 1 7/ 8 4 5/ 8 2 11/16 2 11/16 13 12-1 1/8 78
10 17 1/ 2 2 1/ 8 4 7/ 8 2 7/ 8 4 15 1/ 4 16-1 1/4 110
12 20 1/ 2 2 1/ 4 5 3/ 8 3 1/ 8 4 1/ 4 17 3/ 4 16-1 3/8 160
14 23 2 3/ 8 5 7/ 8 3 5/16 4 5/ 8 20 1/ 4 20-1 3/8 233
16 25 1/ 2 2 1/ 2 6 3 11/16 5 22 1/ 2 20-1 1/2 294
18 28 2 5/ 8 6 1/ 2 3 7/ 8 5 3/ 8 24 3/ 4 24-1 1/2 260
20 30 1/ 2 2 3/ 4 6 5/ 8 4 5 3/ 4 27 24-1 5/8 445
24 36 3 6 7/ 8 4 1/ 2 6 1/ 4 32 24-1 7/8 640

** The 1/4" raised face is not included in the thickness "Y" or "C"
600 LB. FLANGES - INCHES 600 #
Nom. **Y (See Note Above) No. & WNFLG.
Pipe O C Weld Slip on Lap Bolt Size of Wt.
Size INCHES INCHES Neck Thrd. Joint Circle Holes Lbs
1/ 2 3 3/ 4 9/16 2 1/16 7/ 8 7/ 8 2 5/ 8 4 - 5/8 3
3/ 4 4 5/ 8 5/ 8 2 1/ 4 1 1 6 1/ 4 4 - 3/4 3.5
1 4 7/ 8 11/16 2 7/16 1 1/16 1 1/16 3 1/ 2 4 - 3/4 4
1 1/4 5 1/ 4 13/16 2 5/ 8 1 1/ 8 1 1/ 8 3 7/ 8 4 - 3/4 5.5
1 1/2 6 1/ 8 7/ 8 2 3/ 4 1 1/ 4 1 1/ 4 4 1/ 2 4 -7/8 8
2 6 1/ 2 1 2 7/ 8 1 7/16 1 7/16 5 8-3/4 10
2 1/2 7 1/ 2 1 1/ 8 3 1/ 8 1 5/ 8 1 5/ 8 5 7/ 8 8-7/8 14
3 8 1/ 4 1 1/ 4 3 1/ 4 1 13/16 1 13/16 6 5/ 8 8-7/8 18
4 10 3/ 4 1 1/ 2 4 2 1/ 8 2 1/ 8 8 1/ 2 8-1 37
5 13 1 3/ 4 4 1/ 2 2 3/ 8 2 3/ 8 10 1/ 2 8-1 1/8 68
6 14 1 7/ 8 4 5/ 8 2 5/ 8 2 5/ 8 11 1/ 2 12-1 1/8 73
8 16 1/ 2 2 3/16 5 1/ 4 3 3 13 3/ 4 12-1 1/4 112
10 20 2 1/ 2 6 3 3/ 8 4 3/ 8 17 16-1 3/8 189
12 22 2 5/ 8 6 1/ 8 3 5/ 8 4 5/ 8 19 1/ 4 20-1 3/8 226
14 23 3/ 4 2 3/ 4 6 1/ 2 3 11/16 5 20 3/ 4 20-1 1/2 268
16 27 3 7 4 3/16 5 1/ 2 23 3/ 4 20-1 5/8 481
18 29 1/ 4 3 1/ 4 7 1/ 4 4 5/ 8 6 25 3/ 4 20-1 3/4 555
20 32 3 1/ 2 7 1/ 2 5 6 1/ 2 28 1/ 2 24-1 3/4 690
24 37 4 8 5 1/ 2 7 1/ 4 33 24-2 977

** The 1/4" raised face is not included in the thickness "Y" or "C"
900 LB. FLANGES - INCHES 900 #
Nom. **Y (See Note Above) No. & WNFLG.
Pipe O C Weld Slip on Lap Bolt Size of Wt.
Size INCHES INCHES Neck Thrd. Joint Circle Holes Lbs
1/ 2 4 3/ 4 7/ 8 2 3/ 8 1 1/ 4 1 1/ 4 3 1/ 4 4 - 7/8 7
3/ 4 5 1/ 8 1 2 3/ 4 1 3/ 8 1 3/ 8 3 1/ 2 4 - 7/8 7
1 5 7/ 8 1 1/ 8 2 7/ 8 1 5/ 8 1 5/ 8 4 4-1 8.5
1 1/4 6 1/ 4 1 1/ 8 2 7/ 8 1 5/ 8 1 5/ 8 4 3/ 8 4-1 10
1 1/2 7 1 1/ 4 3 1/ 4 1 3/ 4 1 3/ 4 4 7/ 8 4 -1 1/8 14
2 8 1/ 2 1 1/ 2 4 2 1/ 4 2 1/ 4 6 1/ 2 8-1 24
2 1/2 9 5/ 8 1 5/ 8 4 1/ 8 2 1/ 2 2 1/ 2 7 1/ 2 8-1 1/8 36
3 9 1/ 2 1 1/ 2 4 2 1/ 8 2 1/ 8 7 1/ 2 8-1 29
4 11 1/ 2 1 3/ 4 4 1/ 2 2 3/ 4 2 3/ 4 9 1/ 4 8-1 1/4 51
5 13 3/ 4 2 5 3 1/ 8 3 1/ 8 11 8-1 3/8 86
6 15 2 3/16 5 1/ 2 3 3/ 8 3 3/ 8 12 1/ 2 12-1 1/4 110
8 18 1/ 2 2 1/ 2 6 3/ 8 4 4 1/ 2 15 1/ 2 12-1 1/2 187
10 21 1/ 2 2 3/ 4 7 1/ 4 4 1/ 4 5 18 1/ 2 16-1 1/2 268
12 24 3 1/ 8 7 7/ 8 4 5/ 8 5 5/ 8 21 20-1 1/2 372
14 25 1/ 4 3 3/ 8 8 3/ 8 5 1/ 8 6 1/ 8 22 20-1 5/8 562
16 27 3/ 4 3 1/ 2 8 1/ 2 5 1/ 4 6 1/ 2 24 1/ 4 20-1 3/4 685
18 31 4 9 6 7 1/ 2 27 20-2 924
20 33 3/ 4 4 1/ 4 9 3/ 4 6 1/ 4 8 1/ 4 29 1/ 2 24-2 1/8 1164
24 41 5 1/ 2 11 1/ 2 8 10 1/ 2 35 1/ 2 24-2 5/8 2107
** The 1/4" raised face is not included in the thickness "Y" or "C"
1500 LB. FLANGES - INCHES 1500 #
Nom. **Y (See Note Above) No. & WNFLG.
Pipe O C Weld Slip on Lap Bolt Size of Wt.
Size INCHES INCHES Neck Thrd. Joint Circle Holes Lbs
1/ 2 4 3/ 4 7/ 8 2 3/ 8 1 1/ 4 1 1/ 4 3 1/ 4 4 - 7/8 7
3/ 4 5 1/ 8 1 2 3/ 4 1 3/ 8 1 3/ 8 3 1/ 2 4 - 7/8 7
1 5 7/ 8 1 1/ 8 2 7/ 8 1 5/ 8 1 5/ 8 4 4-1 8.5
1 1/4 6 1/ 4 1 1/ 8 2 7/ 8 1 5/ 8 1 5/ 8 4 3/ 8 4-1 10
1 1/2 7 1 1/ 4 3 1/ 4 1 3/ 4 1 3/ 4 4 7/ 8 4 -1 1/8 14
2 8 1/ 2 1 1/ 2 4 2 1/ 4 2 1/ 4 6 1/ 2 8-1 24
2 1/2 9 5/ 8 1 5/ 8 4 1/ 8 2 1/ 2 2 1/ 2 7 1/ 2 8-1 1/8 36
3 10 1/ 2 1 7/ 8 4 5/ 8 2 7/ 8 2 7/ 8 8 8-1 1/4 48
4 12 1/ 4 2 1/ 8 4 7/ 8 3 9/16 3 9/16 9 1/ 2 8-1 3/8 69
5 14 3/ 4 2 7/ 8 6 1/ 8 4 1/ 8 4 1/ 8 11 1/ 2 8-1 5/8 132
6 15 1/ 2 3 1/ 4 6 3/ 4 4 11/16 4 11/16 12 1/ 2 12-1 1/2 164
8 19 3 5/ 8 8 3/ 8 5 5/ 8 5 5/ 8 15 1/ 2 12-1 3/4 273
10 23 4 1/ 4 10 6 1/ 4 7 19 12-2 454
12 26 1/ 2 4 7/ 8 11 1/ 8 7 1/ 8 8 5/ 8 22 1/ 2 16-2 1/8 690
14 29 1/ 2 5 1/ 4 11 3/ 4 9 1/ 2 25 16-2 3/8 1180
16 32 1/ 2 5 3/ 4 12 1/ 4 10 1/ 4 27 3/ 4 16 - 2 5/8 1541
18 36 6 3/ 8 12 7/ 8 10 7/ 8 30 1/ 2 16- 2 7/8 2310
20 38 3/ 4 7 14 11 1/ 2 32 3/ 4 16-3 1/8 2945
24 46 8 16 13 39 16 -3 5/8 5373

SCREWED FITTINGS

3000#
SIZE A B C D E F G H*
1/2 1 5/16 1 1/2 1 2 1/8 2 3/16 1 7/8 1 1/8 1/ 2
3/4 1 1/2 1 13/16 1 1/8 2 5/16 2 9/16 2 1 3/8 9/16
1 1 3/4 2 3/16 1 5/16 2 1/2 2 15/16 2 3/8 1 3/4 11/16
1 1/2 2 3/8 3 1 11/16 3 1/8 3 11/16 3 1/8 2 1/2 11/16
2 2 1/2 3 5/16 1 3/ 4 3 1/2 4 9/16 3 3/8 3 3/ 4
2 1/2 3 1/4 4 2 1/16 4 5/8 5 1/ 4 3 5/8 3 5/8 15/16
6000#
SIZE A B C D E F G H*
1/2 1 1/2 1 13/16 1 1/8 2 7/8 2 13/16 1 7/8 1 1/2 1/ 2
3/4 1 3/4 2 3/16 1 5/16 3 3/8 3 1/8 2 1 3/4 9/16
1 2 2 7/16 1 3/8 3 5/8 3 13/16 2 3/8 2 1/4 11/16
1 1/2 2 1/2 3 5/16 1 3/4 4 3/16 4 3/4 3 1/8 3 11/16
2 3 1/4 4 2 1/16 4 5/8 5 1/4 3 3/8 3 5/8 3/ 4
2 1/2 3 3/4 4 3/4 2 1/2 - - 3 5/8 4 1/4 15/16
* Thread engagement typical for H, J & K
Nominal Outside Desig-
Pipe Size Dia. nation
150# 150# 150# 150# 150# 1/ 8 0.405 Std.
SO-FLG. Lap-FLG. Blind-FLG. LWN-FLG HB-LWN 1/ 8 0.405 X-Stg.
Wt. Wt. Wt. O.D. O.D.
Lbs Lbs Lbs INCHES INCHES 1/ 4 0.540 Std.
1 1 2 1.1875 1/ 4 0.540 X-Stg.
1.5 1.5 2 1.5
2 2 2 1.9375 3/ 8 0.675 Std.
2.5 2.5 3 2.3125 3/ 8 0.675 X-Stg.
3 3 3 2.5625
5 5 4 3.0625 1/ 2 0.840 Std.
8 8 7 3.5625 1/ 2 0.840 X-Stg.
9 9 9 4.25 1/ 2 0.840 160
13 12 17 5.3125 1/ 2 0.840 XX-Stg.
15 13 20 6.443
17 18 27 7.5625 3/ 4 1.050 Std.
28 28 47 9.69 3/ 4 1.050 X-Stg.
40 36 67 12 3/ 4 1.050 160
61 60 102 14.375 3/ 4 1.050 XX-Stg.
83 77 139 15.75 17.125
106 104 187 18 19.625 1 1.315 Std.
109 146 217 19.875 20.9375 1 1.315 X-Stg.
148 159 283 22 23.1875 1 1.315 160
204 195 415 26.125 27.5 1 1.315 XX-Stg.

1 1/ 4 1.660 Std.
300# 300# 300# 300# 300# 1 1/ 4 1.660 X-Stg.
SO-FLG. Lap-FLG. Blind-FLG. LWN-FLG LWN-FLG 1 1/ 4 1.660 160
Wt. Wt. Wt. O.D. O.D. 1 1/ 4 1.660 XX-Stg.
Lbs Lbs Lbs INCHES INCHES
1.5 1.5 2 1.5 1 1/ 2 1.900 Std.
2.5 2.5 3 1.875 1 1/ 2 1.900 X-Stg.
3 3 4 2.125 1 1/ 2 1.900 160
4.5 4.5 6 2.5 1 1/ 2 1.900 XX-Stg.
6.5 6.5 7 2.75
7 7 8 3.3125 2 2.375 Std.
10 10 12 3.9375 2 2.375 X-Stg.
13 14.5 16 4.625 2 2.375 160
23.5 24 28 5.75 2 2.375 XX-Stg.
29 26 37 7
36 38 48 8.125 2 1/ 2 2.875 Std.
56 55 79 10.25 2 1/ 2 2.875 X-Stg.
77 88 122 12.625 2 1/ 2 2.875 160
113 139 183 14.75 2 1/ 2 2.875 XX-Stg.
159 184 241 16.75 18.4375
210 234 315 19 20.5 3 3.5 Std.
253 305 414 21 22.75 3 3.5 X-Stg.
307 375 515 23.125 25 3 3.5 160
490 530 800 27.625 29.625 3 3.5 XX-Stg.

4 4.5 Std.
400 # 400 # 400 # 400 # 400 # 4 4.5 X-Stg.
SO-FLG. Lap-FLG. Blind-FLG. LWN-FLG LWN-FLG 4 4.5 120
Wt. Wt. Wt. O.D. O.D. 4 4.5 160
Lbs Lbs Lbs INCHES INCHES 4 4.5 XX-Stg.
2 2 2 1.5
3 3 3 1.875 5 5.563 Std.
3.5 3.5 4 2.125 5 5.563 X-Stg.
4.5 4.5 6 2.5 5 5.563 120
6.5 6.5 8 2.75 5 5.563 160
8 8 10 3.3125 5 5.563 XX-Stg.
12 11 15 3.9375
15 14 20 4.625 6 6.625 Std.
24 22 33 5.75 6 6.625 X-Stg.
31 29 44 7 6 6.625 120
39 37 61 8.125 6 6.625 160
63 59 100 10.25 6 6.625 XX-Stg.
91 95 155 12.625
129 152 226 14.75 8 8.625 Std.
191 210 310 16.75 8 8.625 60
253 280 398 19 8 8.625 X-Stg.
310 345 502 21 8 8.625 100
378 420 621 23.125 8 8.625 120
539 615 936 27.625 8 8.625 140
8 8.625 XX-Stg.
8 8.625 160
600 # 600 # 600 # 600 # 600 #
SO-FLG. Lap-FLG. Blind-FLG. LWN-FLG LWN-FLG 10 10.750 Std.
Wt. Wt. Wt. O.D. O.D. 10 10.750 X-Stg.
Lbs Lbs Lbs INCHES INCHES 10 10.750 80
2 2 2 1.5 10 10.750 100
3 3 3 1.875 10 10.750 120
3.5 3.5 4 2.125 10 10.750 140
4.5 4.5 6 2.5 10 10.750 160
6.5 6.5 8 2.75
8 8 10 3.3125 12 12.750 Std.
12 11 15 3.9375 12 12.750 40
15 14 20 4.625 12 12.750 X-Stg.
33 31 41 6 12 12.750 60
56 63 68 7.4375 12 12.750 80
66 78 86 8.75 12 12.750 100
97 112 139 10.75 12 12.750 XX-Stg.
177 195 231 13.5 12 12.750 140
215 240 295 15.75 12 12.750 160
259 290 378 17 18.5625
366 400 527 19.5 21.375 14 14.000 Std.
476 469 665 21.5 23.1875 14 14.000 40
612 604 855 24 25.9375 14 14.000 X-Stg.
876 866 1175 28.25 30.0625 14 14.000 80
14 14.000 160

900 # 900 # 900 # 900 # 900 # 16 16.000 Std.


SO-FLG. Lap-FLG. Blind-FLG. LWN-FLG LWN-FLG 16 16.000 40
Wt. Wt. Wt. O.D. O.D. 16 16.000 X-Stg.
Lbs Lbs Lbs INCHES INCHES 16 16.000 80
6 6 4 1.5 16 16.000 160
6 6 6 1.75
7.5 7.5 9 2.0625 18 18.000 Std.
10 10 10 2.5 18 18.000 40
14 14 14 2.75 18 18.000 X-Stg.
22 21 25 4.125 18 18.000 80
36 29 35 4.875 18 18.000 160
31 25 32 5
53 51 54 6.25 20 20.000 Std.
83 81 87 7.5 20 20.000 40
108 105 113 9.25 20 20.000 X-Stg.
172 188 197 11.75 20 20.000 80
245 277 290 14.5 20 20.000 160
326 371 413 16.5
380 397 494 17.75 19.625 24 24.000 Std.
459 488 619 20 21.6875 24 24.000 40
647 670 880 22.25 24.0625 24 24.000 X-Stg.
792 868 1107 24.5 26.375 24 24.000 80
1480 1659 2099 29.5 31.625 24 24.000 160
1500 # 1500 # 1500 # 1500 # 1500 #
SO-FLG. Lap-FLG. Blind-FLG. LWN-FLG LWN-FLG FLANGE STUD SIZE AND MAX
Wt. Wt. Wt. O.D. O.D. PIPE SIZE FLANGE TYPE
Lbs Lbs Lbs INCHES INCHES 2" RF 150
6 6 7 1.5
6 6 10 1.75
7.5 7.5 12 2.0625
10 10 18 2.5
14 14 25 2.75
22 21 39 4.125
36 29 56 4.875
48 38 86 5.25
73 75 133 6.375
132 138 223 7.75
164 170 345 9
258 286 533 11.5
436 485 1025 14.5
667 749 1464 17.75
19.5 21.5
21.75 23.875
23.5 26.25
25.25 28.125
30 33.625

TABLE UW-16.1
MINIMUM THICKNESS FOR COUPLINGS
NPS INCH
J* K* 1/2" 0.14
1/ 2 1/ 2 3/4" 0.16
9/16 9/16 1" 0.22
11/16 11/16 1 1/2" 0.3
11/16 11/16 2" 0.31
3/ 4 3/ 4 2 1/2" 0.37
15/16 15/16
COUPLING THICKNESS
J* K* NPS 3000# 6000#
1/ 2 1/ 2 1/2" 0.1425 0.33
9/16 9/16 3/4" 0.1625 0.35
11/16 11/16 1" 0.2175 0.4675
11/16 11/16 1 1/2" 0.3 0.55
3/ 4 3/ 4 2" 0.3125 0.625
15/16 15/16 2 1/2" 0.375 0.6875
Note: 3000# coupling cannot be used if corrosion
allowance is applied.
Wall Weight SA-105 ANSI B16.5 Flange Temperature/Pressure rating
Thickness Lbs/ Ft. Temp(F°) 150# 300# 600# 900# 1500#
0.068 0.244 < 100 285 740 1480 2220 3705
0.095 0.314 200 260 680 1360 2035 3395
300 230 655 1310 1965 3270
0.088 0.424 400 200 635 1265 1900 3170
0.119 0.535 500 170 605 1205 1810 3015
600 140 570 1135 1705 2840
0.091 0.567 650 125 550 1100 1650 2745
0.126 0.738 700 110 530 1060 1590 2655
750 95 505 1015 1520 2535
0.109 0.850 800 80 410 825 1235 2055
0.147 1.087 850 65 320 640 955 1595
0.138 1.310 900 50 230 460 690 1150
0.294 1.714 950 35 135 275 410 685
1000 20 85 170 255 430
0.113 1.130
0.154 1.473 0 285 740 1480 2220 3705
0.219 1.940
0.308 2.440 SS304/316 ANSI B16.5 Flange Temperature/Pressure rating
Temp(F°) 150# 300# 600# 900# 1500#
0.133 1.678 < 100 275 720 1440 2160 3600
0.179 2.171 200 235 620 1240 1860 3095
0.250 2.850 300 215 560 1120 1680 2795
0.358 3.659 400 195 515 1025 1540 2570
500 170 480 955 1435 2390
0.140 2.272 600 140 450 900 1355 2255
0.191 2.996 650 125 440 885 1325 2210
0.250 3.764 700 110 435 870 1305 2170
0.382 5.214 750 95 425 855 1280 2135
800 80 420 845 1265 2110
0.145 2.717 850 65 420 835 1255 2090
0.200 3.631 900 50 415 830 1245 2075
0.281 4.862 950 35 385 775 1160 1930
0.400 6.408 1000 20 365 720 1090 1820

0.154 3.652 0 275 720 1440 2160 3600


0.218 5.022
0.344 7.450
0.436 9.029

0.203 5.790
0.276 7.660
0.375 10.010
0.552 13.690

0.216 7.57
0.300 10.25
0.438 14.32
0.600 18.58

0.237 10.79
0.337 14.98
0.438 19.00
0.531 22.60
0.674 27.54

0.258 14.62
0.375 20.78
0.500 27.10
0.625 32.96
0.750 38.55

0.280 18.97
0.432 28.57
0.562 36.40
0.719 45.30
0.864 53.16

0.322 28.55
0.406 35.70
0.500 43.39
0.594 50.90
0.719 60.70
0.812 67.80
0.875 72.42
0.906 74.70
0.365 40.48
0.500 54.74
0.594 64.40
0.719 77.00
0.844 89.20
1.000 104.20
1.125 116.00

0.375 49.60
0.406 53.60
0.500 65.40
0.562 73.20
0.688 88.60
0.844 108.00
1.000 125.50
1.125 140.00
1.312 161.00

0.375 54.45
0.438 63.30
0.500 71.93
0.750 109.50
1.406 188.70

0.375 62.44
0.500 82.59
0.500 82.59
0.844 136.32
1.594 244.72

0.375 70.44
0.562 104.44
0.500 93.25
0.938 170.56
1.781 307.84

0.375 78.43
0.594 122.84
0.500 103.91
1.031 208.42
1.969 378.35

0.375 94.41
0.688 170.80
0.500 125.22
1.219 295.94
2.344 540.96
STUD SIZE AND MAXIMUM TORQUE -- SA-193-B7 STUDS
TORQUE STUD QTY STUD SIZE STUD LENGTH R WRENCH SIZE
90 4 5/ 8'' 3-1/2" 17/16''
sure rating BLIND FLANGE WEIGHTS
2500# SIZE 150 300 600 900 1500
6170 1.00 2 4 4 9 12
5655 1.25 3 6 6 10 18
5450 1.50 3 7 8 14 25
5280 2.00 4 8 10 25 39
5025 2.50 7 12 15 35 56
4730 3.00 9 16 20 32 86
4575 4.00 17 28 41 54 133
4425 5.00 20 37 68 87 223
4230 6.00 27 48 86 113 345
3430 8.00 47 79 139 197 533
2655 10.00 67 122 231 290 1025
1915 12.00 102 183 295 413 1464
1145 14.00 139 241 378 494 1729
715 16.00 187 315 527 619 2167
18.00 217 414 665 880 3080
6170 20.00 283 515 855 1107 3875
24.00 415 800 1175 2099 7347
essure rating
2500#
6000
5160
4660
4280
3980
3760
3680
3620
3560
3520
3480
3460
3220
3030

6000
CALCULATIONS FOR ASME CODE SECTION VIII, DIVISION I, 2017 EDITION
1 Pressure Vessel 10.0 API GRAVITY
2 ASME Code Section II 1.0000 SPECIFIC GRAVITY
3 8.33 LBS/GAL
0.4 PSI/VERT.FT
4 Material Database and Temperatures Page 1 of 1
5 Material Properties:
Ambie
6 0 Temp [°F] - maximum design
nt temperature
Design UCS-66 CURVE WITH ALLOWABLE TEMPERATURE REDUCTION UCS-66 TABLE
0 Temp [°F] - minimumStreng
design Streng
temperature
Max (SEE TABLE FOR MATERIAL EXEMPT TEMPERATURE) MATERIAL CURVE
7 Material th th ºF Materials less than 1" thickness may be exempt per UG-20(f). THICKNESS A B C D
8 SA-36 Plate 16,600 16,600 900 Carbon Steels CURVE "B" WITH REDUCTION 39 #N/A #N/A 0.25 18 -20 -55 -55
SA-53 EB Welded Pipe 14,600 14,600 900 SHELL #N/A F #N/A #N/A 2 0.00 #N/A #N/A 0.3125 18 -20 -55 -55
9 SA-106 B Seamless Pipe 17,100 17,100 1,000 NOZZLE 1 #N/A F 0 3 0 #N/A 0.375 18 -20 -55 -55
SA-106 C Seamless Pipe 20,000 20,000 1,000 NOZZLE 2 #N/A F 0 4 0 #N/A 0.4375 25 -13 -40 -55
SA-193 B7 Studs 25,000 25,000 1,000 NOZZLE 3 #N/A F 0 5 0 #N/A 0.5 32 -7 -34 -55
10 SA-234 WPB Fittings 17,100 17,100 1,000 NOZZLE 4 #N/A F 0 40 0 #N/A 0.5625 37 -1 -26 -51
11 SA-105 Forging 20,000 20,000 1,000 NOZZLE 5 #N/A F 0 38 0 #N/A 0.625 43 5 -22 -48
12 SA-516 70 Plate 20,000 20,000 1,000 37 #N/A #N/A 0.6875 48 10 -18 -45
13 SA-414 G Sheet 21,400 21,400 900 HEAD A #N/A F 100 #N/A 27 0.00 #N/A #N/A 0.75 53 15 -15 -42
14 SA-213 TP316L Sms Tube 16,700 16,700 850 Stainless Steel 316L NOZZLE 1 #N/A F 0 41 0 #N/A 0.875 61 23 -9 -36
15 SA-240 316L Plate 16,700 16,700 850 NOZZLE 2 #N/A F 0 7 0 #N/A 1 68 31 -3 -30
16 SA-312 TP316L Sms. and Wld. Pipe 16,700 16,700 850 NOZZLE 3 #N/A F 0 17 0 #N/A 1.125 75 37 2 -26
17 SA-403 316L Sms and Weld Fittings 16,700 16,700 850 45 1.1875 77 40 2 -23
18 SA-479 316L Bar 16,700 16,700 850 HEAD B #N/A F 100 #N/A 29 #N/A #N/A 1.25 80 43 6 -21
19 SA-213 TP316 Sms Tube 20,000 20,000 1,500 Stainless Steel 316 NOZZLE 1 #N/A F 0 42 0 #N/A 1.375 84 47 10 -18
20 SA-240 316 Plate 20,000 20,000 1,500 NOZZLE 2 #N/A F 0 8 0 #N/A 1.5 88 51 14 -14
21 SA-312 TP316 Sms. and Wld. Pipe 20,000 20,000 1,500 18 #N/A #N/A 1.625 92 55 17 -11
22 SA-403 316 Sms and Weld Fittings 20,000 20,000 1,500 SHELL #2 #N/A F #N/A #N/A 46 0.00 #N/A #N/A 1.6875 93 57 19 -10
23 SA-479 316 Bar 20,000 20,000 1,500 HEAD C #N/A F #DIV/0! #N/A 30 0.00 #N/A #N/A 1.75 94 58 20 -8
24 SA-213 TP304L Sms Tube 16,700 16,700 1,200 Stainless Steel 304L 43 #N/A #N/A 1.875 97 61 23 -6
25 SA-240 304L Plate 16,700 16,700 1,200 CLOSURE #N/A F #DIV/0! #N/A 9 0.00 #N/A #N/A 2 99 63 26 -4
26 SA-312 TP304L Sms. and Wld. Pipe 16,700 16,700 1,200 19 #N/A #N/A 2.125 101 65 28 -2
27 SA-403 304L Sms and Weld Fittings 16,700 16,700 1,200 The above temperatures and curves #N/A 47 2.25 102 67 30 0
28 SA-479 304L Bar 16,700 16,700 1,200 are for carbon steels only. 32 2.375 104 69 32 2
29 SA-213 TP304 Sms Tube 20,000 20,000 1,500 Stainless Steel 304 100 44 2.5 105 71 34 4
30 SA-240 304 Plate 20,000 20,000 1,500 100 10 2.625 106 73 36 6
31 SA-312 TP304 Sms. and Wld. Pipe 20,000 20,000 1,500 Note: SA-36 is a curve "A" material. 20 2.75 108 74 38 8
32 SA-403 304 Sms and Weld Fittings 20,000 20,000 1,500 Stainless Steel exemptions fall under 48 2.875 109 76 40 9
33 SA-479 304 Bar 20,000 20,000 1,500 UHA-51. 33 3 110 77 41 11
34 SB-209 6061-T6 plate 0.051-0.249", wld 6,000 6,000 400 Aluminum 49 3.125 111 79 43 12
35 SB-209 6061-T651 plate 0.25-5", wld 6,000 6,000 400 50 3.25 112 80 44 14
36 SB-209 6061-T6 plate 0.051-0.249" 10,900 10,900 400 51 3.375 113 82 46 15
37 SB-209 6061-T651 plate 0.25-4.0" 10,900 10,900 400 52 3.5 114 83 47 17
38 SB-209 6061-T651 plate 4.0-5.0" 10,300 10,300 400 53 3.625 115 85 49 18
39 SB-211 A96061-T6 bar 0.125-0.249", wld 6,000 6,000 400 57 3.75 116 86 50 20
40 SB-234 A96061-T6 tubes 0.025-0.200", wld 6,000 6,000 400 59 3.875 116 88 51 21
41 SB-241 A96061-T6 sms. Pipe, wld 6,000 6,000 400 61 4 117 89 52 23
42 SB-247 A96061-T6 forging, wld 6,000 6,000 400 62 4.125 118 90 54 24
43 SB-308 A96061-T6 shapes, wld 6,000 6,000 400 64 4.25 118 91 55 25
44 Material properties are compliant with ASME Section IID Table 1A 4.375 119 93 56 27
4.5 119 94 57 28
Impact Requirements For Low Temperature Applications 4.625 119 95 58 29
The rules in ASME 8 Div 1 Section UCS 66 provide a good guide to reducing the risk of brittle fracture. 4.75 119 96 59 30
4.875 119 97 60 31
Materials are divided into 4 groups: A) high risk to D) low risk:- 5 119 97 60 32
5.125 119 98 61 33
A) Materials with low toughness or materials that don’t fit into the other groups. 5.25 119 99 62 34
B) Most materials fit into this group 5.375 119 100 63 35
C) Low strength materials; such as an SA516 Grade 60, note: grade 70 goes in B 5.5 119 100 63 36
D) Tough fine grain steels, all normalised grades of SA516. 5.625 119 101 64 37
5.75 120 102 65 38
If in doubt assume A 5.875 120 103 66 38
6 120 104 66 39
As thickness is increases so does the risk of brittle fracture; therefore the temperature before impacts tests are required must get warmer.
This is the basis of Fig UCS 66, which plots each material group between MDMT (Minimum Design Metal Temperature) and thickness.
If the MDMT falls below the appropriate material curve (A to D), Impact testing is mandatory.
However if the item is not highly stressed there is less risk of brittle fracture, UCS-66 permits the impact test temperature to be raised
if the full material thickness is not required. If the resulting test temperature exceeds the values in the UCS 66 table, impact testing is not required.
Residual stresses are present in all welded structures and can be up to yield point in magnitude. Whilst these stresses will not cause failure by
yielding, they could drive a brittle fracture. Therefore stress relief is mandatory on thick material that is prone to brittle fracture (UCS 56).
Allowances for stress relief is built into the code rules, but stress relief of any item when its not required will permit an increase in the impact test
exemption temperature (UCS68c).
Welding defects can also cause brittle fracture; therefore when material thickness exceeds a certain limit, full radiography is required. (Table UCS 57).
The toughness of weld metal must also be demonstrated by production test plates, which are mandatory if impact testing is required.
As the strength of the material increases so does the risk of brittle fracture, particularly as thickness increases. Therefore higher absorbed energy
is required from strong materials above a certain thickness. (Fig UG 84.1).

UCS66, UG20, and UG84 MUST be read very carefully before any decision is made concerning impact testing, as both sections contain
many exceptions and exemptions.

You might also like