You are on page 1of 2995

2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.

40 Page 1
Chevrolet Venture V6-3.4L VIN E 1
Vehicle: Application and ID
Labels

Gross Vehicle Weight Rating - Label

Label - Vehicle Certification

The vehicle certification label is permanently located on the edge of the driver's door. Refer to this label in order to obtain the following
information:
^ The Gross Vehicle Weight Rating (GVWR)
^ The Gross Axle Weight Rating (GAWR), front and rear

The Gross Vehicle Weight (GVW) must not exceed the Gross Vehicle Weight Rating (GVWR).

The GVW is the weight of the vehicle and everything the vehicle carries. Include the following items when figuring the GVW:
^ The base vehicle weight (factory weight)
^ The weight of any added vehicle accessories
^ The weight of the driver and the passenger
^ The weight of any cargo being carried

The front and rear Gross Axle Weights (GAW) must not exceed the Gross Axle Weight Ratings (GAWR), front and rear.

The GAW is the weight exerted on one of the axles (front or rear).
Label - Service Parts ID
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 2
Chevrolet Venture V6-3.4L VIN E 2

Label - Service Parts ID

The service parts identification label has been developed and placed on the vehicle to help service and parts personnel identity parts and options
that were originally installed on the vehicle.

The service parts identification label is located on the inside of the left quarter trim access panel (1). Refer to RPO Code List in General
Information for a definition of the codes that are printed on the service parts identification label or referred to in this service information.
Tire Placard
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 3
Chevrolet Venture V6-3.4L VIN E 3

The tire placard is located on the inside edge of the driver's door. Refer to the tire placard to obtain the following information:
^ Maximum vehicle capacity weight
^ Cold tire inflation pressures
^ Original equipment tire sizes
^ Original equipment tire speed ratings
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 1
Chevrolet Venture V6-3.4L VIN E 4
Vehicle: Application and ID
Vehicle Identification Number (VIN)

Engine ID and VIN Derivative Location

The eighth digit of the Vehicle Identification Number (VIN) identifies the engine. The adhesive-backed labels attached to the engine, laser etching
or stampings on the engine block indicate the engine unit number/date code. All engines are stamped with a VIN derivative

The primary location (1) of the VIN derivative and the secondary location (2) of the VIN derivative for the 3400 (LA1) engine is above the starter
motor on the engine block. For additional information, refer to VIN Derivative.
VIN Derivative

VIN Derivative Table

All engines and transmissions are stamped with a partial Vehicle Identification Number (VIN). A VIN derivative may be used in order to determine
it a vehicle contains the original engine or transmission by matching the VIN derivative positions to their accompanying positions in the complete
VIN. The following table identifies the different VIN derivative characters, the equivalent VIN positions, the character positions and their
respective definitions.

VIN Derivative

A VIN derivative can be used to determine if a vehicle contains the original engine or transmission by matching the VIN derivative positions to
their accompanying positions in the complete VIN:
Transmission ID and VIN Derivative Location
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 2
Chevrolet Venture V6-3.4L VIN E 5

Transmission ID Location

All automatic transmissions have a metal Identification (ID) nameplate (9) attached to the case exterior.
VIN Derivative
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 3
Chevrolet Venture V6-3.4L VIN E 6
VIN Derivative Table

All engines and transmissions are stamped with a partial Vehicle Identification Number (VIN). A VIN derivative may be used in order to determine
it a vehicle contains the original engine or transmission by matching the VIN derivative positions to their accompanying positions in the complete
VIN. The following table identifies the different VIN derivative characters, the equivalent VIN positions, the character positions and their
respective definitions.

VIN Derivative

A VIN derivative can be used to determine if a vehicle contains the original engine or transmission by matching the VIN derivative positions to
their accompanying positions in the complete VIN:
Vehicle Identification

Vehicle Identification

The Vehicle Identification Number (VIN) plate (1) is the legal identifier of the vehicle. The VIN plate is located on the upper left corner of the
instrument panel and can be seen through the windshield from the outside of the vehicle.

Vehicle Identification Number (VIN) System


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 1
Chevrolet Venture V6-3.4L VIN E 7
Vehicle: Application and ID
RPO Codes

RPO Code Label Information

Typical RPO Label

DESCRIPTION
The Regular Production Option (RPO) label is placed on the vehicle to aid service and parts personnel in identifying parts and options
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 2
Chevrolet Venture V6-3.4L VIN E 8
originally installed on the vehicle. A typical RPO label is shown in the accompanying image.

Knowledge of the RPO identification system can help identifying and ordering parts. Systems and assemblies may be uniquely identified by
refering to the label.

GM assigns a three digit/letter code to parts, assemblies, and systems. These RPO codes designate "options" and are assigned by General
Motors. Some system testing and part suppliers require RPO information to accurately match systems, parts and assemblies.

LOCATION OF RPO LABEL


Locations of RPO labels vary by carline.

REPLACEMENT LABELS
Replacement labels are available through GM Service Parts Operations (SPO) for the following:

^ Vehicle Emission Control Information (Exhaust Emission Tune-up)


^ Spare Wheel Caution
^ Jacking
^ Spare Tire Storage
^ Serpentine Belt Routing
^ Engine Fan Caution

These and other labels will be found in the Standard Parts Catalog.

The Vehicle Certification Label, Tire Pressure Placard, and Service Parts Identification Label are not available as service parts.

RPO Code List


RPO Code List

RPO................................................................................................................................................................................................................. Description

ABA................................................................................................................................................................ Seat Configuration #1 (Req. 7 Pass. ZP7);


.............................................................................................................................................................................................. Row 1: Front Buckets - 2;
......................................................................................................................................................................... Row 2: 40/60 Bench - 2 (RPO AT5);
......................................................................................................................................................................... Row 3: 50/50 Bench - 3 (RPO AM9)
ABB................................................................................................................................................................ Seat Configuration #2 (Req. 7 Pass. ZP7);
..................................................................................................................................................................... Row 1: Front Buckets - 2; Row 2/3: Rear
............................................................................................................................................................................................... Buckets - 3/2 (RPO AL4)
ABD................................................................................................................................................................. Seat Configuration #4 (Req. 7 Pass ZP7);
.............................................................................................................................................................................................. Row 1: Front Buckets - 2;
............................................................................................................................................................................ Row 2: Captain Seats - 2 (RPO A04);
............................................................................................................................................................................. Row 3: 50/50 Bench - 3 (RPO AM9)
ABH................................................................................................ Seat Configuration #8 (Req. 7 Pass ZP7); Row 1: Front Buckets - 2; (RPO: AV5);
.............................................................................................................................................................................. Row 2: Solid Bench -2 (RPO AQ3);
.............................................................................................................................................................................. Row 3: Solid Bench - 3 (RPO AN1)
AB3....................................................................................................................................................................................... Seating Arrangement 6 Pass
AB4............................................................................................................................................................. Seating Arrangement 5 Pass, w/Bucket Seats
AB7.................................................................................................................................................................................. Window Tinted, Deep, Liftgate
ACG..................................................................................................................................................................... Filler Opaque Glass, Side RR Window
AG1.................................................................................................................................................................. Adjuster Front Seat Power 6-Way Driver
AG2............................................................................................................................................................ Adjuster, Front Passenger Seat Power 6-Way
AG9.......................................................................................................................................................................... Adjuster Seat Power 6-Way Dr/Pass
AJ1.............................................................................................. Window Tinted Deep, All Except Windshield and Doors (FRT)(Solar Privacy Glass)
AJ7................................................................................................................................. Restraint System FRT Seat, Inflatable, Dr/Pass, Front and Side
AL4............................................................................................................................................... Seat RR Bucket w/Reclin, HDREST (2nd /3rd Rows)
AM7.............................................................................................................................................................. Seat RR Folding (3-Pass Bench) (3rd Row)
AM9.......................................................................................................................... Seat Rr Split Back, Folding (50/50 Split Bench 3-Pass) (3rd Row)
AN2..................................................................................................................................................................... Seat Child Integral Single RH 2nd Row
AN5.............................................................................................................................................................. Seat Child Integral - Dual LH/RH 2nd Row
AP9........................................................................................................................................................................................................... Restraint Cargo
AQ4....................................................................................................................................................................................................................... Seat RR
AR9.............................................................................................................................................................................................. Seat Frt Bucket, Deluxe
AT5........................................................................................................................................... Seat Rr Center, Folding 2-Pass 40/60 Bench, (2nd Row)
AU0.................................................................................................................................. Lock Control Remote Entry (RFA)(Int Lights - On/Fade Oft)
AV5..................................................................................................................................................................................... Seat, Front Bucket, Highback
AX4................................................................................................................................................................ Restraint Conversion Seat, Man, European
A20.......................................................................................................................................... Window, Rear Quarter Vent Swing-Out-Power-Operated
A26.................................................................................................................................................................................. Window European Glazing, All
A31................................................................................................................................................................................... Window Power-Operated Side;
....................................................................................................................................................................................... Domestic Inc.: Express Down;
...................................................................................................................................................................... GME Inc. Auto Down/Auto Up/Anti-jam
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 3
Chevrolet Venture V6-3.4L VIN E 9
BAD................................................................................................................................................................................... Equipment Modification Trim
BAG........................................................................................................................................................................................................ Part PKG Export
BA8..................................................................................................................................................................... Compartment Stowage, FRT Seat, Pass
BS1..................................................................................................................................................................................... Insulation Acoustical Package
BA8........................................................................................................................................................... Compartment Stowage, Front Seat, Passenger
BF1............................................................................................................................................................................................. Covering RR Floor Mats
BF9........................................................................................................................................................................................... Covering FRT Floor Mats
BG9............................................................................................................................................................................................... Covering Floor Rubber
B18................................................................................................................................................................................... Ornamentation Interior, Deluxe
B3V................................................................................................................................................................................................................... Test Water
B37....................................................................................................................................................................... Covering Floor Mat, FRT & RR, AUX
B4U........................................................................................................................................................................................ Performance Package Sport
B57.................................................................................................................................................................................. Ornamentation Exterior, Deluxe
C25..................................................................................................................................................................... Wiper System RR Window, Intermittent
C28............................................................................................................................................................................................. Pump Coolant, Auxiliary
C3L.............................................................................................................................................................................................. GVW Rating 5357 Lbs.
C34..................................................................................................... HVAC System Air Conditioner Heater Combination (FRT/RR w/Rear Controls)
C49................................................................................................................................................................................... Defogger RR Window, Electric
C60............................................................................................................................................. HVAC System Air Conditioner Front Manual Controls
C69...................................................................................................................................................................................................................... Rear A/C
C79......................................................................................... Lamp Interior, Roof Rail, Courtesy & Single Reading (Rows 2/3 - SSD - Row 3 - DDS)
DD9......................................................................................................................... Mirror O/S LH & RH, Remote Control, Electric, Breakaway Color
DH6............................................................................................................................................ Mirror, I/S Sunshade ILLUM and Map HLDR - LH/R)
DK6.................................................................................................................................................................... Console, Interior Roof (Ext. - Inc. DIC)
DK7......................................................................................................................................................................................... Consolette, Overhead Base
DL5................................................................................................................................................. Decal Roadside Service Information (N/A Can/Exp)
DR1............................................................................................................................................................ Mirror 0/S LH & RH, Manual Control, Color
DR5............................................................................................................... Mirror 0/S LH & RH, Remote Control, Electric, Heated Manual Folding,
D55......................................................................................................................................................................................... Console FRT Compt, Floor
D60......................................................................................................................................................................................... Console FRT Compt, Floor
D84............................................................................................................................................................................................ Paint, Custom Two-Tone
D89..................................................................................................................................................................................................... Paint Special Decor
EXP......................................................................................................................................................................................................................... Export
E28................................................................................................................................................................................... Assist Grips, B-Pillar-Mounted
E58.......................................................................................................................................................................................... Door, Electric Sliding Side
E59............................................................................................................................................................................................... LH Power Sliding Door

E88................................................................................................................................................... Pocket Stowage (Cargo Net Storage - RH Sidewall)


FE1...................................................................................................................................................................................... Suspension System Soft Ride
FE2............................................................................................................................................................................. Suspension System Ride, Handling
FE3............................................................................................................................................................................................. Suspension System Sport
FE9.................................................................................................................................................................................... Certification Emission Federal
FR9................................................................................................................................................................................ Ratio Transaxle Final Drive 3.29
GQ1........................................................................................................................................................................................... Axle Rear Standard Ratio
G50............................................................................................................................................................................... Spring, Rear Heavy Duty, VAR 1
G67.............................................................................................................................................................................................. Level Control Auto, Air
IHB.................................................................................................................................................................................................... Trim Interior Design
IHE.................................................................................................................................................................................................... Trim Interior Design
IHN................................................................................................................................................................................................... Trim Interior Design
IPB................................................................................................................................................................................................ Trim Interior Design
IPC.................................................................................................................................................................................................... Trim Interior Design
IPD.................................................................................................................................................................................................... Trim Interior Design
IP2..................................................................................................................................................................................................... Trim Interior Design
JL9.................................................................................................................... Brake System Power, FRT and RR Disc, Antilock, FRT and RR Wheel
JM4.................................................................................................... Brake System Power, FRT Disc, RR Drum, Cast Iron, Antilock, FRT/RR Wheel
KA1........................................................................................................................................................................................................ Heater Seat, FRT
KC4........................................................................................................................................................................................ Cooling System Engine Oil
KG7................................................................................................................................................................................................... Generator 125 AMP
kG9.................................................................................................................................................................................................... Generator 140 AMP
KNB........................................................................................................................................................................................................ Air Cleaner, Dry
K05................................................................................................................................................................................................... Engine Block Heater

K12.................................................................................................................................................................................................... Filter, Air, Pollutant


K29......................................................................................................................................................................................... Module Powertrain Control
K34.......................................................................................................................................................................... Cruise Control Automatic Electronic
K45............................................................................................................................................................................................. Air Cleaner, Heavy Duty
K68................................................................................................................................................................................................... Generator, 105 AMP
LA1........................................................................................................................................................................... Engine, Gas, 6 Cyl. 3.4L, MFI, HO
MXO....................................................................................................................................................... Merchandises TRANS AUTO Provisions, O/D
M15........................................................................................................................................ Trans, Auto 4-Spd, HMD, (4T65-E) Enhanced Electronic
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 4
Chevrolet Venture V6-3.4L VIN E 10
NB8........................................................................................................................................................................ Emission Override California System
NC1....................................................................................................................................................................................... Emission, System California
NC7......................................................................................................................................................................... Emission, Override - Federal System
NF2................................................................................................................................................................................. Emission System Federal, Tier 1
NG1................................................................................................................................ Certification Emission, Geographically Restricted Registration
NK4................................................................................................................................................................................... Steering Wheel, Sport Leather
NM8............................................................................................................................................................................... Leaded Fuel System Compatible
NP7................................................................................................................................................................................ Steering Column EEG Approved
NV6................................................................................................................................................................................. Steering Power, Reduced Effort
NW9....................................................................................................................................................................................... Traction Control Electronic
NY8............................................................................................................................................................................................................ Shield Exhaust
N05...................................................................................................................................................................................... Lock Control Fuel Filler Cap

N30............................................................................................................................................................................ Steering Wheel, Deluxe (Urethane)


PB4................................................................................................................................................................................................................ Lock, Wheel
PG1.................................................................................................................................................................................................... Wheels 15 x 6, Steel
PH3.................................................................................................................................................. Wheels 15 x 6, Aluminum Cast 115 mm Bolt Circle
P42......................................................................................................................................................................................................... Tires Self Sealing
TL4............................................................................................................................................................................................................... Grille Painted
TT5................................................................................................................................................................................................ Headlamps Halogen, 2
TU8................................................................................................................................................................................... Lamp INTR, Stop, High Level
T2H.................................................................................................................................................. Ornamentation EXTR, Export Unique Requirement
T2J.................................................................................................................................................... Ornamentation INTR, Export Unique Requirement
T62.................................................................................................................................................................... Lamps System Daytime Running, Export
T65.................................................................................................................................................................... Lamps System Daytime Running, Export
T84................................................................................................................................................................... Headlamps RH Rule of the Road, E Mark
T89....................................................................................................................................................................................... Lamps Tail and Stop. Export
T90.......................................................................................................................................................................... Lamps Signaling and Marker, Export
UA6............................................................................................................................................................................................... Theft Deterrent System
UD4.................................................................................................................................................................................. Alarm Vehicle Speed, 120 K/H
UD7........................................................................................................................................................................................................ Rear Parking Aid
UH8.................................................................................................................... Cluster Instrument, Coolant Temperature, Trip Odometer, Tachometer

UK3............................................................................................................................................. Electronic System Steering Wheel Accessory Controls


UK6............................................................................................................................................................ Radio Control, RR Seat, and Earphone Jacks
UL0.......................................................................... Radio AM/FM Stereo, Seek/Scan, Auto Reverse Music Search Cassette, Auto Tone, Clock, ETR
UM7......................................................................................................................................................... Radio AM/FM Stereo, Seek/Scan, Clock, ETR
UN0.............................................................................................................. Radio AM/FM Stereo, Seek/Scan, Compact Disc, Auto Tone, Clock, ETR
UP0................................................................................................................ Radio AM/FM Stereo, Seek/Scan, Compact Disc, Equalizer, Clock, ETR
UX6...................................................................................................................................................................................... Speaker System Front, Dual
UZ4............................................................................... Speaker System, Four Dual Front Door Extended Range, Dual Rear Liftgate Extended Range
UZ5........................................................................................................... Speaker System, Four Dual Front Door Coaxial, Dual Rear Liftgate Coaxial
U1N.................................................................................... Radio AM/FM Stereo, Seek/Scan, Auto Rev Music Search Cass, Clock, Eqlzr, RDS, ETR
U1P........................................................................................................................... Radio AM/FM Stereo, Seek/Scan, CD, Clock, EQLZR, RDS ETR
U1Q......................................................................... Radio AM/FM Stereo, Seek/Scan, Auto Rev Music Search Cass, CD, Clock, EQLZR, RDS, ETR
U18............................................................................................................................................................................ Speedometer-lnstrument Kilo/Miles
U19................................................................................................................................................. Speedometer-Instrument Kilo/Miles; Kilo Odometer

U2E......................................................................................................................................... Cluster Instrument, Coolant Temperature, Trip Odometer


U29........................................................................................................................................................................................... Lamp INTR, I/P Courtesy
U42................................................................................................................................................................................ Entertainment System, Rear Seat
U76........................................................................................................................................................................................ Antenna, Windshield Radio
VH7.......................................................................................................................................................................................................... Bumper Custom
VH9........................................................................................................................................................................ Envelope Owner Information Manual
VK3............................................................................................................................................................................. License Plate Front Mounting Pkg
VZ6......................................................................................................................................................................................... Calibration Speedometer A
V08....................................................................................................................................................................................... Cooling System Heavy Duty
V1B............................................................................................................................................................................................. Discount Value Package
V2G.................................................................................................................................................................................................... Credit Full Fuel Fill
V41.............................................................................................................................................................................................................. Kit Accessory
V54.................................................................................................................................................................................... Luggage Carrier Roof, Painted
V73.......................................................................................................................................................................................... Vehicle Statement US/Can
V92........................................................................................................................................................................................................ Trailer Provisions
XCK......................................................................................................................................................... Tire Frt 215/70R15 WOL PE ST TL AL2 97S
XPA....................................................................................................................................... Tire Frt P215/70R15 WOL PE ST TL AL2 97S (Inc. P42)
XPK...................................................................................................................................................... Tire Frt P215/70R15 BW R/PE ST TL ALS 97S
XPU........................................................................................................................... Tire Frt P215/70R15 BW R/PE ST TL AL2 97S (Olds Req. FE3)
X88.............................................................................................................................................................................. Conversion Name PLT Chevrolet
YCK................................................................................................................................ Tire Rear P215/70R15 WOL PE ST TL AL2 97S Self Sealing
YB6...................................................................................................................................................................................................... Axle (Base Equip)
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 5
Chevrolet Venture V6-3.4L VIN E 11
YD5................................................................................................................................................................................... Spring Front, Base Equipment
YD6..................................................................................................................................................................................... Spring Rear, Base Equipment
YF5................................................................................................................................................................................ Certification Emission California
YNA................................................................................................................................................ Tire Rear P205/65R15 BW R/PE ST TL HWY 94H
YPA..................................................................................................................................................... Tire Rear P215/70R15 WOL PE ST TL AL2 97S
YPK.................................................................................................................................................... Tire Rear P215/70R15 BW R/PE ST TL ALS 97S
YPU.................................................................................................................................................... Tire Rear P215/70R15 BW R/PE ST TL AL2 97S
Y1F................................................................................................................................................................................................ Primary Color Exterior
Y11......................................................................................................................................................................................... Gold Package - Oldsmobile
Y4T............................................................................................................................................................................................... Merchandised PKG LT
Y91............................................................................................................................................................................ Merchandised PKG Luxury Edition
Y92............................................................................................................................................................................ Merchandised PKG Special Edition
ZP7........................................................................................................................................................................................ Seating Arrangement 7 Pass
ZP8........................................................................................................................................................................................ Seating Arrangement 8 Pass
ZX2............................................................................................................................................... Seating Arrangement Driver and Passenger Highback
ZY7........................................................................................................................................................... Color Combination Two Tone, Lower Accent
Z10............................................................................................................................................................................. Merchandised Package Cargo Van
Z49..................................................................................................................................... Export Canadian Modifications Mandatory Base Equipment
Z5X........................................................................................................................................................................... Mirror Provisions Arabic Language
01U.......................................................................................................................................................................... Primary Color Exterior, Special, (96)
09U............................................................................................................................. Primary Color Exterior, Crimson king (Metallic (Pont Req. D89)
1CL........................................................................................................................................................................................ Bumper Height Adjustment
14B..................................................................................................................................................................... Trim Combination Cloth Light Gray (B)
14C..................................................................................................................................................................... Trim Combination Cloth Light Gray (C)
14D............................................................................................................................................................. Trim Combination Cloth Light Gray (E) (92)
14E.............................................................................................................................................. Trim Combination Vinyl Light Gray/Cloth Light Gray
141......................................................................................................................................................................................... Interior Trim Light Gray (I)
14N.................................................................................................................................................................... Trim Combination Vinyl Light Gray (N)
142.................................................................................................................................................................. Trim Combination Leather, Light Gray (2)
16U......................................................................................................................................................................... Primary Color Exterior, Bright White
17L........................................................................................................................................................... Secondary Color Exterior, Silvermist MT (97)
17U............................................................................................................................................................... Primary Color Exterior, Silvermist Metallic
28U....................................................................................................................................................... Primary Color Exterior, Black Sapphire Metallic
30U................................................................................................................................................... Primary Color Exterior, International Blue Metallic
31U....................................................................................................................................................... Primary Color Exterior, Fernmist Green Metallic
49L...................................................................................................................................................... Secondary Color Exterior, Light Sandrift Metallic
49U......................................................................................................................................................... Primary Color Exterior, Light Sandrift Metallic
52B................................................................................................................................................................. Trim Combination Cloth Light Neutral (B)
52C................................................................................................................................................................. Trim Combination Cloth Light Neutral (C)
521..................................................................................................................................................................................... Interior Trim Light Neutral (I)
522.......................................................................................................................................................... Trim Combination Leather, LT Neutral (2) (92)
561............................................................................................................................................................................. Trim Combination, Med. Neutral II
6F5............................................................................................................................................................................................... Wiring Provisions Roof
6Y2........................................................................................................................................................................................ Rear Seat - Delete (3rd Seat
64B................................................................................................................................................................. Trim Combination Cloth, MED DK Sable)
64C.................................................................................................................................................................. Trim Combination Cloth, MED DK Sable
641...................................................................................................................................................................................... Interior Trim MED DK Sable
642............................................................................................................................................................... Trim Combination Leather, MED DK Sable
65U...................................................................................................................................................... Primary Color Exterior, Smokey Carmel Metallic
72U.................................................................................................................................................................... Primary Color Exterior, Redfire Metallic
9C6......................................................................................................................................................................................... SEO Vehicle Taxi Cab Inc.
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 1
Chevrolet Venture V6-3.4L VIN E 12
Vehicle: Symptom Related Diagnostic Procedures

Air Pressure Test


Air Pressure Test

1. Cover the pressure relief valve.


2. Turn the vehicle ventilation fan to HIGH.
3. Close all of the windows and doors.
4. Use one of the following items in order to listen for escaping air along the door and window seals:

* A stethoscope
* A piece of heater hose

Air/Wind Noise
Air/Wind Noise

The following conditions cause most windnoise:

* Leaking seals
* Misaligned body surfaces

There are 3 basic types of windnoise:

* Whistle
* Roar
* Rush

When moving at highway speeds, the air pressure inside of the vehicle becomes significantly greater than the air pressure outside. If a leak exists,
the escaping air causes a hiss or a whistle.

Air passing over or through an opening between 2 body surfaces causes wind roar. Adjusting the alignment of body surfaces may correct wind roar.

Air passing over the vehicle body causes wind rush. Wind rush is related to the aerodynamics of the vehicle.

Determine whether the windnoise is wind whistle or wind roar before concluding that it is wind rush. Wind whistle and wind roar can be repaired,
but the intrinsic aerodynamics of the vehicle cannot be repaired.

Use the following procedure in order to diagnose wind whistle or wind roar:

1. Note the details about the windnoise.

* Determine the perceived location.


* Determine the location of greatest volume.
* Determine when the wind noise occurs.
* Note the vehicle speed.
* Note the interior fan speed.
* Note the position of the windows.
* Identify what it sounds like.

2. Inspect the vehicle for all possible causes of the windnoise.


3. Test drive the vehicle in order to determine whether the windnoise is internal or external.

Soap Suds or Bubble Test


Soap Suds or Bubble Test

1. Cover the pressure relief valve.


2. Turn the vehicle ventilation fan to HIGH.
3. Close all of the windows and doors.
4. Apply a soapy solution to all potential leak areas.
5. Look for bubbles that reveal escaping air.
6. Consider the following procedure as an alternative to pressurizing the vehicle interior:

1. Use an air compressor air hose.


2. Do not exceed 207 kPa (30 psi).
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 2
Chevrolet Venture V6-3.4L VIN E 13

Tracing Powder or Chalk Test


Tracing Powder or Chalk Test

1. Clean the weather-strips with solvent.


2. Clean the contact surfaces with solvent.
3. Apply powder or chalk in an unbroken line to the contact surface of the weather-strip around the perimeter of the following surfaces:

* The rear compartment lid


* The door
* The door window
* The hood

4. Ensure that the surrounding areas are free of chalk or powder.

Important: Do not slam the panel.

5. Close the panel completely.


6. Inspect the applied line on the weather-strip.
The weather-strip will be marred where contact is good. A corresponding imprint will be on the mating surfaces.
7. Gaps or irregularities in the powder or chalk line indicate a poor seal.

Exterior Windnoise
Exterior Windnoise

Exterior windnoise will be louder with 1 or more of the windows open. Windnoise is caused by air passing over the following items:

* The body panels


* The seams
* The openings

Notice: If masking the grille or headlamp bezel areas, care must be taken not to restrict airflow. Restricting airflow can cause vehicle
overheating.

1. Test drive the vehicle.


2. Lower each window in order to determine the location of the windnoise.
3. Stop the vehicle.
4. Use a screwdriver or masking tape in order to temporarily repair the following items:

* The body panels


* The seams
* The openings

5. Tape over the gaps and moldings separately.


6. Test drive the vehicle.
7. Continue to tape over the gaps and moldings.
8. The origin of the windnoise is located when the windnoise stops.

Interior Windnoise
Interior Windnoise

Interior windnoise will not be heard with a lowered window. Interior windnoise is caused by air leaving the inside of the vehicle through a seal or a
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 3
Chevrolet Venture V6-3.4L VIN E 14
seam.

1. Tape over the pressure relief valves in order to increase the air pressure within the vehicle.
2. Test drive the vehicle.
3. Listen for windnoise whistle.
4. Stop the vehicle.
5. Use masking tape in order to make temporary repairs.
6. If you are still unable to determine the source of the interior windnoise, perform 1 or more of the following tests:

* The Tracing Powder or Chalk Test


* The Air Pressure Test
* The Soap Suds or Bubble Test

Body Waterleak Repair


Body Waterleak Repair

Waterleak Diagnosis

Caution: When the vehicle interior has been exposed to extensive water intrusion, such as waterleaks, window left open, driving through high
water and so forth, the Sensing and Diagnostic Module (SDM) and the SDM connector may need to be replaced. With the ignition OFF, inspect the
area under the front seat and the area around the SDM, including the carpet. If any significant soaking or evidence of significant soaking is
detected, the water must be removed, water damage repaired and the SDM and the SDM connector MUST be replaced. Before attempting any of
these repairs, the SIR system must be disabled. Refer to the Supplemental Inflatable Restraint (SIR) System for instructions on how to disable the
SIR system. Failure to disable the SIR system may result in possible air bag deployment, personal injury or otherwise unneeded SIR system repairs.

GM vehicles are designed in order to operate in normal environmental conditions. The design criteria for sealing materials and components is
sufficient to withstand natural elements. The specifications do not take into consideration any of the artificial conditions that may be encountered in
high pressure car washes.

The watertest procedure correlates to natural elements. The watertest procedure will determine the ability of a vehicle to perform under normal
operating conditions.

Repairing waterleaks involves the following actions:

* Proper testing
* Proper diagnosis

The following steps are included in waterleak repairs:

* Adjusting misaligned components


* Application of approved repair materials

In order to diagnose waterleaks, find the condition in which the waterleaks occur. The following list indicates some examples of waterleak
conditions:

* The leak is noticed only when the vehicle is parked on an incline.


* Water is in the spare tire compartment.

If the general leak area is found, isolate the exact entry point by using one of the following tests:

* A water hose test


* An air hose test

If the leak source is not obvious, use watertest equipment in order to determine the leak source.
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 4
Chevrolet Venture V6-3.4L VIN E 15

Remove the inner trim panels or any components as needed in order to locate and confirm the repairs.

Localized Testing (Spot Testing)


Localized Testing (Spot Testing)

Important: Pinpoint the leak area before making any repair. Do not perform random repairs. Random repairs temporarily restrict water
entry and make future diagnosis and repair more difficult.

Perform the localized testing with either water or air. Begin testing at the base of the suspected area. Continue testing the suspected area until you
locate the leak.

Continue the localized testing in the same general area in order to locate all possible leaks.

Air Hose Test


Air Hose Test

1. Apply a liquid soap bubble solution to the suspected leak area.

2. Apply air pressure with an air hose from the inside of the vehicle. Do not exceed 207 kPa (30 psi).
3. Observe the outside of the suspected leak area for bubbles.

Water Hose Test


Water Hose Test

1. Have an assistant detect the actual leak point inside the vehicle.

2. Apply an unrestricted water flow. Use a hose without a nozzle.


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 5
Chevrolet Venture V6-3.4L VIN E 16

3. Begin at the base of the suspected leak area. Move the water flow slowly upward.

Repair Instructions
Stationary Window Waterleak Repair

Caution: When working with any type of glass or sheet metal with exposed or rough edges, wear approved safety glasses and gloves in order to
reduce the chance of personal injury.

Caution: When the vehicle interior has been exposed to extensive water intrusion, such as waterleaks, window left open, driving through high
water and so forth, the Sensing and Diagnostic Module (SDM) and the SDM connector may need to be replaced. With the ignition OFF, inspect the
area under the front seat and the area around the SDM, including the carpet. If any significant soaking or evidence of significant soaking is
detected, the water must be removed, water damage repaired and the SDM and the SDM connector MUST be replaced. Before attempting any of
these repairs, the SIR system must be disabled. Refer to the Supplemental Inflatable Restraint (SIR) System for instructions on how to disable the
SIR system. Failure to disable the SIR system may result in possible air bag deployment, personal injury or otherwise unneeded SIR system repairs.

Use the kit GM P/N 12346284 or the equivalent in order to repair waterleaks without removing and reinstalling the window. Use the following
method only when using the urethane adhesive furnished in the kit:

1. Remove the reveal moldings in the area of the leak.


Remove the garnish moldings or finishing lace as needed in order to locate the source of the leak.
2. Mark the location of the leak.
3. Apply water to the area of the leak while performing the following steps:

1. Push outward on the window in the area of the leak in order to determine the extent of the leak.
2. Mark the extent of the leak area.

4. From the outside of the body, use water in order to clean any dirt or foreign material from the leak area.
Use an air hose in order to dry the area.

5. Use a sharp knife in order to trim off the uneven edges of the urethane adhesive material (1) at the leak point.
Trim off the uneven edge of urethane adhesive material 75 to 100 mm (3 to 4 in) on both sides of the leak point or leak area.
6. Prime (2) the affected area using Pinch-Weld Primer, Black Number 3.
Allow the primer to dry for 10 minutes.
7. Apply the urethane adhesive material at the following locations:

* The leak point


* On both sides of the leak point or leak area

8. Apply the urethane adhesive material 75-100 mm (3-4 in) on both sides of the leak point or leak area.
9. Use a flat-bladed tool (3) in order to work the urethane into the leak point of the original material and body. This action ensures a watertight
seal.
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 6
Chevrolet Venture V6-3.4L VIN E 17

Important: Do not run a heavy stream of water onto freshly applied urethane adhesive.

10. Use warm or hot water in order to test the area.


Ensure that the leak is corrected.
11. Replace all of the previously removed components.
12. Clean the excess urethane adhesive from the surface of the repaired window.
Use a damp cloth in order to apply the GM Window Cleaner GM P/N 1050427 or isopropyl alcohol.
13. Allow the window to air dry.
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 1
Chevrolet Venture V6-3.4L VIN E 18
Vehicle: Programming and Relearning

Control Module References

Crankshaft Position (CKP) - Variation Learn Procedure


The crankshaft position system variation compensating values are stored in the PCM non-volatile memory after a learn procedure has been
performed. If the actual crankshaft position system variation is not within the crankshaft position system variation compensating values stored in
the PCM, DTC P0300 may set. Refer to Diagnostic Aids for DTC P0300.

The Crankshaft Position System Variation Learn Procedure should be performed if any of the following conditions are true:
^ DTC P1336 is set.
^ The PCM has been replaced.
^ The engine has been replaced.
^ The crankshaft has been replaced.
^ The crankshaft harmonic balancer has been replaced.
^ The crankshaft position sensor has been replaced.

IMPORTANT: The scan tool crankshaft position system variation learn function will be inhibited if engine coolant temperature is less than 70°C
(158°F). Allow the engine to warm to at least 70°C (158°F) before attempting the crankshaft position system variation learn procedure.

The scan tool crankshaft position system variation learn function will be inhibited if any Powertrain DTCs other than DTC P1336 are set before or
during the crankshaft position system variation learn procedure. Diagnose and repair any DTCs if set. Refer to applicable DTCs.

The crankshaft position system variation learn function will be inhibited if the PCM detects a malfunction involving the camshaft position signal
circuit, the 3X reference circuit, or the 24X reference circuit. If a malfunction has been indicated, refer to the following list to diagnoses the system
or sensor.
^ DTC P0336 Crankshaft Position (CKP) Sensor Performance.
^ DTC P1374 Crankshaft Position (CKP) High to Low Resolution Frequency Correlation.
^ DTC P0341 Camshaft Position (CMP) Sensor Performance.

The scan tool crankshaft position system variation learn function will not be enabled until engine coolant temperature reaches 70°C (158°F)

Selecting the crankshaft position system variation learn procedure on the scan tool will command the PCM to enable CKP system variation learn
fuel cutoff and allow the crankshaft position system variation compensating values to be stored in the PCM. The PCM must detect an engine speed
of 5150 RPM (CKP system variation learn fuel cutoff) during the crankshaft position system variation learn procedure to store the crankshaft
position system variation compensating values and complete the procedure.

IMPORTANT: Set the vehicle parking brake and block the drive wheels when performing the Crankshaft Position System Variation Learning
Procedure in order to prevent personal injury. Release the throttle when the engine reaches the second fuel cut off. Leaving the throttle open during
the fuel cut off will allow the engine to decel at an even rate. Once the learn procedure is completed, the PCM will return the engine control to the
operator and the engine will respond to the throttle position.

1. Set the parking brake.


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 2
Chevrolet Venture V6-3.4L VIN E 19
2. Block the drive wheels.
3. Ensure the hood is closed.
4. Start the engine and allow engine coolant temperature to reach at least 70°C (158°F).
5. Turn off the ignition switch.
6. Select and enable the crankshaft position variation learn procedure with the scan tool.
7. Start the vehicle.
8. Apply and hold the service brake pedal firmly.
9. Ensure the transaxle is in park.
10. Increase accelerator pedal position until the fuel cutoff is reached at 5150 RPM. Release the accelerator pedal after the second fuel cutoff has
been reached.
11. The crankshaft position system variation compensating values are learned when the RPM decreases back to idle. If the procedure terminates.
12. Observe DIG status for DIG P1336.
13. If the scan tool indicates that DIG P1336 ran and passed, the crankshaft position system variation learn procedure is complete. If the scan tool
indicates DTC P1336 failed or not run, determine if other DTCs have set. If DTCs other than P1336 are not set, repeat the crankshaft position
system variation learn procedure as necessary.
Feature Customization - Changing Modes
1. Turn off the IP dimmer switch.
2. Turn the ignition switch to the LOCK position.
3. Remove the BCM PRGRM fuse.
4. Turn the ignition switch to the ACC position. The BCM flashes the fasten belts indicator and sounds the chime 4 times, which indicates that
BCM type 4 is installed on the vehicle. At this point, the BCM has entered the feature customization mode.
5. In order to change the theft deterrent/shock sensor mode, turn the headlamp switch from OFF to PARK and back to OFF.The BCM flashes
the fasten belts indicator and sounds the chime a number of times equivalent to the theft deterrent/shock sensor mode. A transition past mode
4 repeats the sequence starting with mode 1.
6. Complete the following steps in order to change the theft deterrent arm/disarm mode:
6.1. Insert the key in the left front, right front, or liftgate door lock cylinder.
6.2. Rotate the key from the center to the unlock position.
6.3. Press the horn button on the remote keyless entry transmitter.
6.4. Count the number of chimes that you hear. The number of chimes tells you which mode you have set.
6.5. Press the horn button again in order to change the mode. Continue to press the button until you hear the number of chimes that indicates
the mode that you want.
6.6. Turn the key back to the center position and remove the key from the door key cylinder.

In order to exit and save the current feature customization modes use the following procedure:
1. Turn the ignition switch to the LOCK position.
2. Reinstall the BCM PRGRM fuse.

If you are unable to change locking modes link

Feature Customization - Changing the Interior Lighting Mode


Perform the following procedure to change the interior lighting mode:
1. Turn OFF the I/P dimmer switch.
2. Turn the ignition switch to the LOCK position.
3. Remove the BCM PRGRM fuse.
4. Turn the ignition switch to the ACC position.
- The BCM sounds the chime a number of times equivalent to the BCM type installed on the vehicle (1, 2, 3 or 4 chimes).
- Now the BCM has entered the feature customization mode.
5. To advance the interior lighting mode, cycle the I/P dimmer switch from OFF to DOME and back to OFF.

The BCM sounds the chime a number of times equivalent to the lighting mode currently set. A transition past mode 4 repeats the sequence starting
with mode 1.

To exit and save the current customization mode:


1. Turn the ignition switch to the LOCK position.
2. Reinstall the BCM PRGRM fuse.

Feature Customization - Delayed Illumination


- Enabled (modes 2 and 4): The interior courtesy lights turn ON for 25 seconds, then fade to OFF after the last door is closed.
- Disabled (modes 1 and 3): The interior lights turn OFF after the last door is closed.

Feature Customization - Dome Lamp, IP Courtesy Lamps and Cargo Lamp


The operation of these lamps is described as part of the interior courtesy lights operation. The BCM provides power (CKT 1393) and ground (CKT
690) to these lamps controlling their operation.
Feature Customization - Door Key Unlock Illumination (BCM Type 4 Only)
The BCM grounds CKT 690 for 36-44 seconds activating the interior courtesy lights, when the following conditions are met:
- The ignition switch is in the LOCK or the OFF position.
- The interior lamps override switch is in the ON position (interior courtesy lights enabled).
- Unlock the left front, the right front or the liftgate door using a door key cylinder lock (grounding CKT 781).
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 3
Chevrolet Venture V6-3.4L VIN E 20

Feature Customization - Entering Programming Mode


The feature customization mode is used to configure the BCM to function in various applications. The BCM can be customized to change the
following vehicle functions:
- Interior Lighting Features
- Door Lock System
- Keyless Entry System
- Content Theft Deterrent System

In order to enter the feature customization mode perform the following steps:
1. Turn the ignition switch to the LOCK position.
2. Remove the BCM PRGRM fuse.
3. Turn the ignition switch to the ACC position. When entering the feature customization mode, the BCM first identifies what type of BCM is
installed on the vehicle by flashing the fasten seat belts indicator and sounds the chime 2, 3 or 4 times depending on the type of BCM used on
the vehicle. There are 3 different types of BCM that can be installed on the vehicle based on the vehicle option content that matches the BCM
capabilities. Ensure that the BCM installed on the vehicle is compatible with all of the features on the vehicle. Refer to Body Control System
circuit description for BCM identification. For more information on features that can be customized, refer to:
- Interior Lights Circuit Description
- Automatic Door Lock System Description
- Keyless Entry System Circuit Description
- Content Theft Deterrent (CTD) Circuit Description

Feature Customization - Exit Illumination


- Enabled (modes 3 and 4): The interior courtesy lights turn ON for 25 seconds upon removing the key from the ignition switch.
- Disabled (modes 1 and 2): The interior courtesy lights stay off upon removing the key from the ignition switch.
Feature Customization - Inadvertent Load (Battery Rundown) Protection
The BCM has a feature called inadvertent load (battery rundown) protection. The BCM de-energizes CKT 328 and CKT 1398 9-11 minutes after
the ignition switch has been turned from the ACC or the RUN position to the LOCK or the OFF position. The BCM restores power to CKT 328 and
CKT 1393 when the interior lamps override switch is activated (interior courtesy lights enabled) and under the following conditions:
- Turning the ignition switch from the LOCK or the OFF position, to the ACC or the RUN position.
- Removing the key from the ignition lock cylinder.
- Opening any vehicle door.
- Turning the IP dimmer switch to the DOME position.
- Activating any of the roof rail reading lights.
- The BCM receives a message from the Remote Control Door Lock Receiver (BCM type 3 or 4 only).
- Locking a door using the key (BCM type 4 only).

The inadvertent battery power rundown protection feature is mileage-sensitive. Vehicles with less than 15 (24 km) total accumulated miles (km)
have a 2 minute and 32 second - 3 minute and 18 second time-out instead of a 10 minute time-out.

Feature Customization - Interior Lamps Override Switch


The interior lamps override switch is located in the overhead console switchbank. Pressing the symbol on the bottom of the rocker switch overrides
the control of the interior lights. This action interrupts the voltage supply from CKT 1393 to CKT 328, deactivating all of the interior lights.

Interior Lights Circuit Description

Feature Customization - IP Compartment Lamp


The IP compartment lamp activates when the IP compartment is open. The IP compartment lamp has a switch that closes (providing ground to the
lamp) when the IP compartment is open. The IP compartment lamp switch opens when the IP compartment is closed. The IP compartment lamp
switch receives voltage through CKT 328 and ground through CKT 150. The IP compartment lamp is protected by the inadvertent load (battery
rundown) protection in case that the IP compartment is left open.

Feature Customization - IP Dimmer Switch


The IP dimmer switch allows the operator to activate the interior courtesy lights from inside the vehicle. When the IP dimmer switch is in the
DOME position, the switch sends a ground signal to the BCM through CKT 156. This action causes the BCM to activate the interior courtesy
lights. When the IP dimmer switch is in the OFF position, the BCM deactivates the interior courtesy lights. With the ignition switch in the LOCK or
OFF position, the IP dimmer switch is protected by the inadvertent load (battery rundown) protection in case the IP dimmer switch is left in the
DOME position.

The IP dimmer switch is also used to change the interior lighting modes during the feature customization. Refer to Feature Customization for more
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 4
Chevrolet Venture V6-3.4L VIN E 21
information. In addition, the IP dimmer switch is also utilized to enter the input/output test during BCM diagnostics.
Feature Customization - Keyless Entry Unlock Illumination (BCM Type 3 and 4 Only)
The BCM grounds CKT 690 for 36-44 seconds, activates the interior courtesy lights when the following conditions are met:
- The ignition switch is in the LOCK or the OFF position.
- All of the vehicle doors are closed.
- The IP dimmer switch is in the OFF position.
- The interior lamps override switch is in the ON position (interior courtesy lights enabled).
- The BCM receives a message from the Remote Control Door Lock Receiver (RCDLR) in order to unlock the doors.

Feature Customization - Remote Activation Verification (RAV) Customization

Perform the following steps in order to verify your remote activation customization:

IMPORTANT: If the ignition switch is turned OFF or the driver door is opened while the Body Control Module (BCM) is in the customization
process, the process will be terminated and the BCM will remain in the most recent mode.

1. Remove the BCM PRGRM fuse from the fuse panel. Refer to Fuse Block in Wiring Systems.
2. Close all of the doors.
3. Close the liftgate.
4. Turn the ignition to ACC.
The seat belt telltale will flash and the chime will sound 1-4 times in order to indicate that the body control module (BCM) is in the feature
customization mode.
5. Press the transmitter LOCK button.
The seat belt telltale will flash and the chime will sound 1-2 times in order to indicate which remote unlock control mode the BCM is in. Each
time the transmitter LOCK button is pressed, the mode number will advance. A transition past mode 4 will start over again at mode 1.
6. Turn the ignition OFF.
7. If you wish to customize other features, customize the features before reinstalling the BCM PRGRM fuse block.
8. Replace the BCM PRGRM fuse back into the fuse panel. Refer to Fuse Block in Electrical Diagnosis. Your current customization is now
saved.

Feature Customization - Remote Unlock Control Customization

Perform the following steps in order to customize the remote unlock control:

IMPORTANT: If the ignition switch is turned OFF or the driver door is opened while the Body Control Module (BCM) is in the customization
process, the process will be terminated and the BCM will remain in the most recent mode.

1. Remove the BCM PRGRM fuse from the fuse panel.


2. Close all of the doors.
3. Close the liftgate.
4. Turn the ignition to ACC.
The seat belt telltale will flash and the chime will sound 1-4 times in order to indicate that the body control module (BCM) is in the feature
customization mode.
5. Press the transmitter UNLOCK button.
The seat belt telltale will flash and the chime will sound 1-2 times in order to indicate which remote unlock control mode the BCM is in.Each
time the transmitter UNLOCK button is pressed, the mode number will advance. A transition past mode 2 will repeat and start again at
model.
6. Turn the ignition OFF.
7. If you wish to customize other features, customize the features before reinstalling the BCM PRGRM fuse into the fuse panel.
8. Replace the BCM PRGRM fuse back into the fuse panel.
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 5
Chevrolet Venture V6-3.4L VIN E 22

Feature Customization - Roof Rail Reading Lamps


These lamps have switches that allow the operator to activate them. The switches, upon activation, provide ground to these lamps turning them to
the ON position. The switches obtain ground through CKT 650. The BCM does not turn on these lamps with the rest of the interior courtesy lights.
Power to the roof rail reading lamps is provided by the BCM through CKT 328, so that they are protected by the inadvertent load (battery rundown)
protection in case they are left in the ON position.

Feature Customization - Sunshade Illuminated Vanity Mirrors


The sunshade illuminated vanity mirror lamps activate when the mirror cover is open. The sunshade illuminated vanity mirror has a switch that
closes (providing ground to the lamps) when the mirror cover is open, and the switch opens when the cover is closed. The switch receives ground
through CKT 650.

Power to the sunshade illuminated vanity mirror is provided by the BCM through CKT 328, so that they are protected by the inadvertent load
(battery rundown) protection in case that a mirror cover is left open.

Feature Customization - Theater Dimming


The BCM dims the interior courtesy lights slowly from a full brightness to the OFF position in 3 seconds. This feature starts anytime the BCM is
turning off the interior courtesy lights.

Theater dimming does not work when turning the IP dimmer switch from the DOME position to the OFF position or when the illumination feature
is cancelled by locking the doors with a power door lock switch. Also, theater dimming does not work when the exit illumination feature is
disabled.

Feature Customization - Vehicle Speed Input


The BCM monitors the vehicle speed input to determine the total distance traveled in order to change the inadvertent battery rundown protection
timer.

The BCM determines the distance traveled by interfacing with the vehicle speed CKT 389 which makes a ground transition 4000 times per 1.6 km
(1 mile) traveled. Once the vehicle has been driven past the 15 mile (24 km) mark, the BCM changes inadvertent battery power rundown protection
timer from 3 minutes to 10 minutes.

In addition, the BCM uses the vehicle speed CKT 389 for the operation of the turn signal reminder.

If the inadvertent battery power rundown protection stays at 3 minutes on vehicles with more than 15 miles (24 km), refer to Audible Warnings for
possible malfunction of the turn signal reminder.

Feature Customization - Windshield Header Courtesy/Reading Lamps


The operation of these lamps is described as part of the interior courtesy lights operation. The BCM provides power (CKT 328) and ground (CKT
690) to these lamps, controlling their operation.

In addition, these lamps have switches that allow the operator to turn them on when the interior courtesy lights are off. The switches, upon
activation, provide ground to these lamps turning them to the ON position. The switches obtain ground through CKT 650. Power to these lamps is
provided by the BCM through CKT 328, so that they are protected by the inadvertent load (battery rundown) protection in case they are left in the
ON position.

Instrument Panel Cluster (IPC) - Programming/Synchronization


TOOLS REQUIRED
Scan Tool
When installing a new IP cluster it must be synchronized to the Supplemental Inflatable Restraint (SIR) module in order to synchronize the new
cluster, perform the following steps:
1. Connect the to the Data Link Connector (DLC).
2. Proceed to the SPECIAL FUNCTIONS key under INSTRUMENT PANEL CLUSTER.
3. Select the SYNCHRONIZE IPC and SIR key.
4. The screen will display: IPC and SIR modules-Now synchronizing modules.
5. If the procedure is completed successfully the screen will display: Module Synchronization Complete.
6. If communication is lost with the SIR or IPC, the screen will display: Loss of Communications with Vehicle - Check Diagnostics Link
Connector - Check Ignition (On/Off).

Memory Seat Calibration Procedure


MEMORY SEAT CALIBRATION PROCEDURE

The memory seat module uses position sensor inputs to establish soft stop locations for the adjuster motors several millimeters ahead of the
physical limits of the adjuster assembly. After replacing a memory seat module or adjuster components, it may be necessary to reset the adjuster
motor soft stop locations. When the repair procedure has been completed, operate the seat adjuster switch in every direction until the seat adjuster
reaches its mechanical hard stop by repeatedly pressing and releasing the switch as necessary.
Power Sliding Door (PSD) - Re-Initialization
IMPORTANT: Before you perform the PSD re-initialization, check for Diagnostic Trouble Codes (DTCs) by performing Diagnostic Mode 1.
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 6
Chevrolet Venture V6-3.4L VIN E 23
Refer to Diagnostic Modes in Power Sliding Door Diagnostic Information.

Perform the following PSD re-initialization procedure when any of the following conditions occur:
^ The PSD is inoperative.
^ Reconnecting the vehicle battery.
^ After recharging the vehicle battery.
^ After reinstalling or replacing the radio fuse located in the underhood accessory wiring junction block.
^ Exiting any of the diagnostic modes.

Perform this procedure in order to re-initialize the PSD:


1. Set the PSD on/off switch in the overhead console to the off position.
2. Manually open the PSD completely.
3. Manually close and latch the PSD.
4. Remove the RADIO fuse for 30 seconds.
5. Reinstall the RADIO fuse.
6. Wait 10 seconds.
7. Set the PSD on/off switch in the overhead console to the on position.
8. Press, then release either PSD open/close switch in order to completely open the PSD.
9. Wait 5 seconds.
10 Press, then release either PSD open/close switch in order to allow the PSD to close completely.
11. Wait 5 seconds.
12. Repeat steps 7 through 10 and re-check for proper PSD operation.

Remote Keyless Entry (RKE) - Transmitter


If you lose a transmitter, program the old and new transmitter(s) into the remote control door lock receiver's memory. Up to 4 transmitters may be
programmed.

IMPORTANT: Once the remote control door lock receiver enters the programming/diagnostic mode, the programming of the first transmitter
erases all previous transmitter programming information, requiring the programming of all transmitters.

Program only 1 vehicle remote control door lock receiver at a time. If more than 1 receiver is being programmed at the same time, it is possible that
the same transmitter could be programmed to more than 1 remote control door lock receiver.

Perform the following steps in order to program the transmitter:


1. Remove the ignition key from the ignition lock cylinder.
2. Remove the BCM PRGRM fuse from the fuse panel.
3. Close all of the doors.
4. Close the liftgate.
5. Turn the ignition lock cylinder to ACC.
6. Turn the ignition lock cylinder to OFF, and then back to ACC within 1 second.
7. Open and close any vehicle door.
A chime will be heard when the system enters the BCM programming/diagnostic mode.

IMPORTANT: After 7 seconds, a chime may be heard confirming successful synchronization. It is necessary to wait approximately 14
secondsfor a second chime that will confirm successful programming.

8. Press and hold the transmitter LOCK and UNLOCK buttons simultaneously for 14 seconds.
9. Repeat the previous step on each additional transmitter to be programmed.
10. Remove the ignition key from the ignition lock cylinder.
11. Install the BCM PRGRM fuse back into the fuse panel.
Remote Keyless Entry (RKE) - Transmitter - Resynchronization
The Remote Function Actuation (RFA) system uses a continually changing code for increased security. Normally, the remote control door lock
receiver will keep track of this changing code. However, loss of synchronization will occur if the transmitter is activated more than 256 times while
out of range of the vehicle.

If the transmitter stops working, you may need to synchronize the transmitter to the vehicle remote control door lock receiver. In order to
synchronize the transmitter to the vehicle remote control door lock receiver, press and hold the LOCK and the UNLOCK buttons for at least 7
seconds. If your vehicle is equipped with content theft deterrent, the horn will sound once the synchronization is complete. Inspect the transmitter
operation when the process is complete.

Theft Deterrent - Quick Learn Procedure - Keys Only


IMPORTANT:
^ Additional Master Theft Deterrent Controller Keys (Black) or Valet Keys (Gray) may be added (up to 10 keys) using this procedure when
there is an available learned Master Theft Deterrent Controller Key (Black).
^ This procedure adds keys only, it does not erase previously learned keys.
^ The keys to be learned must duplicate the mechanical cut of the current key.
1. With a previously learned Master Theft Deterrent Controller Key (Black),turn ON the ignition, with the engine OFF.
2. Turn OFF the ignition and remove the key.
3. Within 10 seconds insert the key to be learned and turn ON the ignition, with the engine OFF. The vehicle has now learned the new key(s).
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 7
Chevrolet Venture V6-3.4L VIN E 24

Theft Deterrent - Replacement Keys - IGN CYL, or PCM


IMPORTANT:
^ If replacing a theft deterrent controller module with an GM Service Parts Operation (SPO) Replacement Part, the module will learn keys
immediately. The existing PCM however, must learn the new fuel continue password when the theft deterrent controller module is replaced.
^ If replacing a PCM with a GM Service Parts Operation (SPO) Replacement Part, after programming, these modules will learn the incoming
fuel continue password immediately upon receipt of a password message. Once a password message is received, and a password is learned, a
learn procedure must be performed to change this password again. A PCM which has been previously installed in another vehicle will have
learned the other vehicles fuel continue password and will require a Learn procedure after programming to learn the current vehicle's
password.
^ When performing the 10 Minute or the 30 Minute Re-Learn Procedures, all previously learned keys will be erased from the VTD module's
memory.
^ Additional keys may be learned immediately after the 10 Minute or 30 Minute Re-Learn Procedure by inserting the additional key to be
learned and turning the ignition to RUN within 10 seconds of removing the previously learned key.
Theft Deterrent - 10 Minute Re-Learn Procedure
Use this procedure after replacing:
^ The keys/lock cylinders
^ The theft deterrent controller module
^ The PCM (if necessary, see Important above)

Tools Required
^ Tech 2
^ Techline Terminal with current Service Programing System (SPS) software
1. Connect the Tech 2 Diagnostic tool.
2. Select Request Information under Service Programing.
3. Disconnect the Tech 2 from the vehicle and connect it to a Techline Terminal.
4. On the Techline Terminal, select Theft Module Re-Learn under Service Programming.
5. Disconnect the Tech 2 from the Techline Terminal and re-connect it to the vehicle.
6. Turn ON the ignition, with the engine OFF, using a Master Pass Key III Key (Black).
7. Select VTD Re-Learn under Service Programming.
8. At this point the Tech 2 must remain connected for the duration of the 10 minute Re-Learn period.
9. Observe the Security telltale, after approximately 10 minutes the telltale will turn off. (The vehicle is now ready to re-learn the key
information and/or passwords on the next ignition switch transition from OFF to CRANK)
10. Turn OFF the ignition and wait 5 seconds.
11. Start the vehicle (the scan tool has now learned the key and password information).
12. With the scan tool, clear any DTCs

Theft Deterrent - 30 Minute Re-Learn Procedure


Use this procedure after replacing:
^ The keys/lock cylinders
^ The theft deterrent controller module
^ The PCM (if necessary, see important above)
1. Turn ON the ignition, with the engine OFF using a Master Pass Key III Key (Black).
2. Observe the Security telltale, after approximately 10 minutes the telltale will turn off.
3. Turn OFF the ignition, and wait 5 seconds.
4. Repeat steps 1 through 3 two more times for a total of 3 cycles or 30 minutes.

IMPORTANT: The vehicle learns the key information and/or passwords on the ignition switch transition from OFF to CRANK. You must turn
the ignition OFF before attempting to start the vehicle.

5. Start the vehicle (the vehicle has now learned the key and password information).
6. With a scan tool, clear any DTCs.
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 1
Chevrolet Venture V6-3.4L VIN E 25
Engine: Description and Operation

Drive Belt System Description


The drive belt system consists of the following components:
^ The drive belt
^ The drive belt tensioner
^ The drive belt idler pulley
^ The crankshaft balancer pulley
^ The accessory drive component mounting brackets
^ The accessory drive components
- The power steering pump, if belt driven
- The generator
- The A/C compressor, if equipped
- The engine cooling fan, if belt driven
- The water pump, if belt driven
- The vacuum pump, if equipped
- The air compressor, if equipped

The drive belt system may use one belt or two belts. The drive belt is thin so that it can bend backwards and has several ribs to match the grooves in
the pulleys. There also may be a V-belt style belt used to drive certain accessory drive components. The drive belts are made of different types of
rubbers (chloroprene or EPDM) and have different layers or plys containing either fiber cloth or cords for reinforcement.

Both sides of the drive belt may be used to drive the different accessory drive components. When the back side of the drive belt is used to drive a
pulley, the pulley is smooth.

The drive belt is pulled by the crankshaft balancer pulley across the accessory drive component pulleys. The spring loaded drive belt tensioner
keeps constant tension on the drive belt to prevent the drive belt from slipping. The drive belt tensioner arm will move when loads are applied to the
drive belt by the accessory drive components and the crankshaft.

The drive belt system may have an idler pulley, which is used to add wrap to the adjacent pulleys. Some systems use an idler pulley in place of an
accessory drive component when the vehicle is not equipped with the accessory.

Engine Component Description


The cylinder block is made of cast alloy iron. The cylinder block has 6 cylinders that are arranged in a V shape. There are 3 cylinders in each bank.
The cylinder banks are set at a 60 degree angle from each other.

Starting from the front of the engine, the right bank cylinders are 1, 3, 5. The left bank cylinders are 2, 4, 6.

Four main bearings support the crankshaft. The crankshaft is retained by the bearing caps. The bearing caps are machined with the block for proper
alignment and clearances. The main bearing caps are drilled and tapped for the structural oil pan side bolts.

The aluminum cylinder heads have individual intake and exhaust ports for each cylinder. The valve guides are pressed in. The roller rocker arms
are located on a pedestal in a slot in the cylinder head. The roller rocker arms are retained on individual threaded bolts.

The crankshaft is cast nodular iron with deep rolled fillets on all 6 crankpins and all 4 main journals. Four steel-backed aluminum bearings are
used. The #3 bearing is the end-thrust bearing.

The camshaft is made from a new metal composite design. The camshaft profile is a hydraulic roller design. The camshaft is supported by 4
journals. The camshaft includes an oil pump drive gear.

The pistons are cast aluminum using 2 compression rings and 1 oil control ring. The piston pin is offset 0.8 mm (0.031 inch) towards the major
thrust side. This placement allows for a gradual change in thrust pressure against the cylinder wall as the piston travels its path. The pins are
chromium steel. The pins have a floating fit in the pistons. The pins are retained in the connecting rods by a press fit.

The connecting rods are made of forged steel. Full pressure lubrication is directed to the connecting rods by drilled oil passages from the adjacent
main bearing journal.

A roller rocker type valve train is used. Motion is transmitted from the camshaft through the hydraulic roller lifter and from the pushrod to the roller
rocker arm. The rocker arm pivots on the needle roller bearings. The rocker arm transmits the camshaft motion to the valve. The rocker arm
pedestal is located in a slot in the cylinder head. The rocker arm is retained in the cylinder head by a bolt. The pushrod is located by the rocker arm.

The intake manifold is a 2-piece cast aluminum unit. The intake manifold centrally supports a fuel rail with 6 fuel injectors.

The exhaust manifolds are cast nodular iron.

Installation Precautions
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 2
Chevrolet Venture V6-3.4L VIN E 26

General Information on Engine Service

Caution: Before removing or installing any electrical unit, or when a tool or equipment could easily come in contact with "live" or "hot all
the times" exposed electrical terminals, disconnect the negative battery cable to help prevent personal injury and/or damage to the vehicle
or components. Unless instructed otherwise, the ignition switch must be in the OFF or LOCK position.

Caution: Before servicing any electrical component, the ignition key must be in the OFF or LOCK position and all electrical loads must be
OFF, unless instructed otherwise in these procedures. If a tool or equipment could easily come in contact with a five exposed electrical
terminal, also disconnect the negative battery cable. Failure to follow these precautions may cause personal injury and/or damage to the
vehicle or its components.

Notice: The following information on engine service should be noted carefully, as it is important in preventing damage and contributing to
reliable engine performance.

Use a block of wood under the oil pan when raising or supporting the engine. Jacking against the oil pan may cause the oil pan to bend against
the pump screen and result in a damaged pickup unit.
Any time the throttle body or throttle body air inlet tube is removed, the intake opening should be covered. Covering the opening will protect
against the accidental entrance of foreign material which could follow the intake passage into the cylinder and cause extensive damage when the
engine is started.

Notice: Pull on the spark plug boot, the heat shield or use an approved spark plug boot removal tool, twisting a half-turn to release the seal while
removing. Do not pull on the spark plug wire or it may be damaged.

Notice: Clean the spark plug recess area before removing the spark plug. Failure to do so could result in engine damage because of dirt or
foreign material entering the cylinder head, or by the contamination of the cylinder head threads. The contaminated threads may prevent the
proper seating of the new plug. Use a thread chaser to clean the threads of any contamination.

Notice: Allow the engine to cool before removing the spark plugs. Attempting to remove the spark plugs from a hot engine may cause the plug
threads to seize, causing damage to cylinder head threads.

Lubrication Description

Front View
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 3
Chevrolet Venture V6-3.4L VIN E 27

Rear View
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 4
Chevrolet Venture V6-3.4L VIN E 28

Right View

Full pressure lubrication, through a full flow oil filter, is furnished by a gear type oil pump. The oil is drawn up through the pickup screen and the
tube. The oil passes through the pump to the oil filter.

The oil filter is a full flow paper element unit. An oil filter bypass is used in order to ensure oil supply during the following conditions:
^ On a cold start
^ If the filter is plugged
^ If the filter develops excessive pressure drop

The bypass is designed to open at 69 - 83 kPa (10 - 12 psi).

A new priority oil delivery system supplies oil first to the crankshaft journals. The oil from the crankshaft main bearings is supplied to the
connecting rod bearings by intersecting the passages drilled in the crankshaft. The passages supply the oil to the crankshaft main bearings and the
camshaft bearings through the intersecting vertical drilled holes. The oil passages from the camshaft journals supply oil to the hydraulic lifters.

The hydraulic lifters pump oil up through the pushrods to the rocker arms. The cast dams in the crankcase casting direct the oil that drains back
from the rocker arms in order to supply the camshaft lobes. The camshaft chain drive is lubricated by indirect oil splash.

Replacing Engine Gaskets


1. Do not reuse any gasket unless otherwise specified. Reusable gaskets will be identified in the service procedure. Do not apply sealant to any
gasket or sealing surface unless called out in the service procedure.
2. Use a rubber mallet in order to separate components. Bump the part sideways in order to loosen the components. Perform the bumping at the
bends or at the reinforced areas in order to prevent the distortion of components.

Important: Do not use any other method or technique in order to remove the gasket material from a components.

Do not use the following items in order to clean the gasket surfaces:
^ Abrasive pads
^ Sand paper
^ Power tools

These methods of cleaning may damage the component.


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 5
Chevrolet Venture V6-3.4L VIN E 29

Abrasive pads also produce a fine grit that the oil filter cannot remove from the oil. This grit is abrasive and may cause internal engine damage.

3. Remove all of the gasket and the sealing material from the component using a plastic or a wood scraper. Do not gouge or scrape the sealing
surfaces.

Important: Do not allow the sealant to enter any blind threaded holes. The sealant may cause the following conditions:
^ Prevent you from properly seating the bolt
^ Cause damage when you tighten the bolt

4. When assembling components, use only the sealant specified in the service procedure. Ensure that the sealing surfaces are clean and free of
debris or oil. When applying sealant to a component, apply a bead size as specified in the service procedure.
5. Tighten the bolts to the specifications.
Separating Parts
In addition to the RTV sealant's sealing capabilities, the RTV sealants may form an adhesive bond between the components. This may make the
components difficult to remove or to separate. The RTV sealant is weakest in shear strength and parts. If possible, bump the components
sideways rather than using prying tools in order to remove the components. This technique prevents damage when the bonding strength of the
RTV sealant is stronger than the component itself. Perform bumping at the bends or at the reinforced areas in order to prevent part distortion.

Service Precautions
Important: Follow the engine service information below. This information is important in order to prevent damage and in contributing to
reliable engine performance.

In order to avoid damage to the engine oil pan, use a block of wood between the jack and the oil pan. Ensure that the block of wood extends past
the complete width of the oil pan. Due to the small clearance between the oil pan and the oil pump screen, jacking against the oil pan may cause
the oil pan to bend against the pump screen. This condition results in a damaged oil pick-up unit.

Caution: Refer to Battery Disconnect Caution in Service Precautions.

When working on the engine, remember that the 12 volt electrical system is capable of causing short circuits. When performing any work where
electrical terminals may possibly be grounded, disconnect the ground cable of the battery at the battery.

Any time you remove the air cleaner, cover the intake opening. This procedure protects against the accidental entrance of foreign material.
Foreign material may follow the intake passage into the cylinder. This condition causes extensive damage when you start the engine.

In the mechanical procedures described, generally no references will be made to the removal of optional equipment such as the power steering
pump, the air conditioning compressor, etc.

If you need to remove any optional equipment in order to perform other service, refer to the appropriate section for the specific information.

Tools and Equipment


Work in a clean and well-lit area. Have the following components available before you begin to work:
^ A suitable parts cleaning tank
^ A compressed air supply
^ Trays, in order to keep the parts and the fasteners organized
^ An adequate set of hand tools

An approved engine repair stand will prevent personal injury or damage to the engine components. The special tools are designed in order to
quickly and safely accomplish the operations for which the tools are intended. Using the tools will minimize possible damage to the engine
components. Precision measuring tools are required for the inspection of certain critical components. Torque wrenches are needed for the correct
assembly of various parts.

Use of RTV and Anaerobic Sealer


The following 2 types of sealer are commonly used in engines:
^ The RTV sealer
^ The anaerobic gasket eliminator sealer
Follow the service procedure instructions. Use the correct sealer in the proper place in order to prevent oil leaks. Do not interchange the 2 types
of sealers. Use the sealer recommended in the service procedure.

Applying RTV Sealer


^ Do not use the room temperature vulcanizing (RTV) sealant in areas where extreme temperatures are expected. These areas include the
following locations:
- The exhaust manifold
- The head gasket
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 6
Chevrolet Venture V6-3.4L VIN E 30
- The other surfaces where gasket eliminator is specified
^ Use a rubber mallet in order to separate the components sealed with RTV sealant. Bump the part sideways in order to shear the RTV sealer.
Perform the bumping at the bends or the reinforced areas in order to prevent distortion of the components. The RTV sealant is weaker in
shear (lateral) strength than in tensile (vertical) strength.

Important: Do not use any other method or technique in order to remove the gasket material from a component.

^ Do not use the following items in order to clean the gasket surfaces:
- Abrasive pads
- Sand Paper
- Power tools
These methods of cleaning may damage the part.
Abrasive pads also produce a fine grit that the oil filter cannot remove from the oil. This grit is abrasive and may cause internal engine damage.
^ Remove all of the gasket material from the component using a plastic or a wood scraper. Use Loctite (R) brand gasket remover P/N 4MA or
the equivalent. Follow all of the safety recommendations and the directions that are on the container.

Important: Do not allow the sealer to enter the blind threaded holes. The sealer may cause the following conditions:
- Prevent you from properly seating the bolt
- Cause damage when you tighten the bolt

^ Apply the RTV sealant to a clean surface. Use a bead size as specified in the procedure. Apply the bead to the inside of any bolt holes.
^ Assemble the components while the RTV sealant is still wet (within 3 minutes). Do not wait for the RTV sealant to skin over.

Important: Do not overtighten the bolts.


^ Tighten the bolts to specifications.

Applying Anaerobic Sealer


The anaerobic gasket eliminator hardens in the absence of air. This type of sealer is used where 2 rigid parts (such as castings) are assembled
together. When 2 rigid parts are disassembled and no sealer or gasket is readily noticeable, the parts were probably assembled using a gasket
eliminator.

Important: Do not use any other method or technique in order to remove the gasket material from a component.

Do not use the following items in order to clean the gasket surfaces:
^ Abrasive pads
^ Sand paper
^ Power tools
These methods of cleaning may damage the part.
Abrasive pads also produce a fine grit that the oil filter cannot remove from the oil. This grit is abrasive and may cause internal engine damage.
^ Remove all of the gasket material from the component using a plastic or a wood scraper. Use Loctite (R) brand gasket remover P/N 4MA or
the equivalent. Follow all of the safety recommendations and the directions that are on the container.
^ Apply a continuous bead of the gasket eliminator to 1 flange. Clean and dry any surfaces that you will reseal.

Important: Anaerobic sealed joints that are partially torqued and allowed to cure more than 5 minutes may result in incorrect shimming and
sealing of the joint.

^ Do not allow the sealer to enter the blind threaded holes. The sealer may cause the following conditions:
- Prevent you from properly seating the bolt
- Cause damage when you tighten the bolt
^ Spread the sealer evenly in order to get a uniform coating on the sealing surface.
^ Tighten the bolts to the specifications.
^ Remove the excess sealer from the outside of the joint.
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 1
Chevrolet Venture V6-3.4L VIN E 31
Engine: Testing and Inspection
Base Engine Misfire Diagnosis
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 2
Chevrolet Venture V6-3.4L VIN E 32
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 1
Chevrolet Venture V6-3.4L VIN E 33
Engine: Testing and Inspection
Engine Noise Diagnosis

Engine Noise Diagnosis (Symptom - Cause/Correction)

Exhaust
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 2
Chevrolet Venture V6-3.4L VIN E 34

Valve Train

Base Engine

Engine Noise Diagnosis (General Description)


Notice: Some engine noise is characteristic to the design. Compare the sounds in other engines in order to make sure that you are not trying to
correct a normal condition.
^ Use the following four elements when diagnosing engine noise:
- The type of noise
- Under which operating conditions the noise exists
- At what rate the noise exists in the engine
- At what location the noise exists in the engine
^ Compare the sounds in other engines in order to ensure that the noise is not a normal condition.
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 3
Chevrolet Venture V6-3.4L VIN E 35
^ Engine noise is generally synchronized to either engine speed (caused by the crankshaft, connecting rods or pistons) or one-half engine speed
(valve train noise). Try to determine the rate at which the noise is occurring.

Main Bearing Noise


^ Damaged or worn main bearing noise is revealed by dull thuds or knocks which happen on every engine revolution. This noise is loudest
when the engine is under heavy load.
^ An intermittent rap or knock sharper than a worn main bearing indicates excessive crankshaft end play.
^ The following conditions cause main bearing noise:
- Low oil pump pressure
- Thin, diluted, or dirty oil and/or filter
- Excessive main bearing clearance
- Excessive crankshaft end play
- Out-of-round crankshaft journals
- Excessive belt tension
- A loose crankshaft pulley
- A loose flywheel or torque converter
- A loose main bearing cap
- Belt pilling

Connecting Rod Bearing Noise


A damaged or worn connecting rod bearing will produce a knock under all speeds. During the early stages of wear, connecting rod noise may be
confused with piston slap or loose piston pins. Connecting rod knock noise increases in volume with engine speed. This noise is loudest on
deceleration.
The following conditions cause connecting rod bearing noise:
^ Excessive bearing clearance
^ A worn crankshaft connecting rod journal
^ Thin, diluted, or dirty oil and/or filter
^ Low oil pressure
^ Crankshaft connecting rod journals out-of-round
^ A misaligned connecting rod
^ Connecting rod nuts not properly torqued
^ The wrong bearing inserts or misaligned bearing half

Timing Chain and Sprocket Noise


Engines equipped with a timing chain and sprockets may produce noise. The most common noise is a high frequency, light-knocking sound. This
sound will generally be the same in intensity whether the engine is idling, operating at high speeds, or under load.
The following conditions may cause timing chain and sprocket noise:
^ A worn timing chain
^ A damaged sprocket
^ A loose sprocket on the camshaft or crankshaft
^ Too much end play in the camshaft or crankshaft

Piston Noise
Piston pin, piston, and connecting rod noise are hard to separate. A loose piston pin causes a sharp double knock usually heard when the engine
is idling, or during sudden acceleration then deceleration of the engine. A piston pin that has been improperly fitted will emit a light ticking noise
that is more noticeable with no load on the engine. Excessive piston-to-cylinder bore clearance will cause a piston slap noise. The noise is similar
to a metallic knock, as if the piston were slapping the cylinder wall during the stroke.
As with most engine noise, understanding the cause of the noise will help you imagine what the noise sounds like. An indication of piston slap is
a decrease in noise as the engine warms up. When the engine is cold, the piston-to-bore clearance is greater and piston slap will be louder. The
following conditions may cause piston noise:
^ A worn or loose piston pin
^ Improper pin fit
^ Excessive piston-to-cylinder bore clearance
^ Lack of lubrication
^ Carbon deposits on top of the piston striking the cylinder head
^ Worn or broken piston ring land
^ Broken or cracked piston
^ Misaligned connecting rods
^ Worn or damaged rings
^ Excessive ring land clearance
^ Insufficient ring-end gap clearance
^ Piston 180 degrees out of position
^ Incorrect skirt profiles

Flywheel Noise

Notice: Converter bolts that are too long may dimple the torque converter clutch apply surface and cause a shudder condition.

A loose or cracked flywheel will produce an irregular thud or click. Complete the following steps in order to test for a loose or cracked flywheel:
1. Operate the vehicle at approximately 32 km/h (20 mph).
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 4
Chevrolet Venture V6-3.4L VIN E 36
2. Shut off the engine.
If a thud is heard, the flywheel may be loose or damaged. This type of thud is loudest on deceleration.
Loose torque converter-to-flywheel or flywheel-to-crankshaft bolts will resemble a bearing knock. This condition produces several raps during
quick acceleration on a free-running engine. Depending on the idle smoothness, when the transaxle is in gear, the noise may or may not appear.
Inspect the torque converter-to-flywheel and the flywheel-to-crankshaft bolts before attempting to investigate any bearing-related knock.

Valve Train Noise


A light tapping at one-half engine speed, or any varying frequency, may indicate a valve train problem. These tapping noises increase with the
engine speed. Warm up the engine before attempting to judge the valve train noise. This will bring all of the engine components to a normal state
of expansion. Run the engine at various speeds and listen for engine noise with the hood closed.

Caution: The following procedure is not recommended on engines with stainless steel exhaust manifolds because manifold temperature
will exceed the flash point of the oil causing a fire with possible personal injury.

If the valve mechanism is abnormally noisy, remove the valve rocker arm covers. Use a stethoscope in order to determine which valve train
components are causing the noise. The causes of the valve noise include the following conditions:
^ Broken or weak valve springs
^ Sticking or warped valves
^ Bent push rods
^ Dirty, stuck, or worn valve lifters
^ Damaged or improperly machined camshaft lobes
^ Insufficient or poor oil supply to the valve train (low oil pressure)
^ Excessive valve stem-to-guide clearance
^ Worn valve guides
^ Worn push rods
^ Worn valve rocker arms
^ A broken valve rocker arm bolt
^ Loose or worn valve rocker arm attachments
^ Missing or improperly positioned lifter guides (roller lifter engines)
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 1
Chevrolet Venture V6-3.4L VIN E 37
Engine: Testing and Inspection
Oil Consumption Diagnosis
An engine that has excessive oil consumption uses 0.9L (1 qt.) of oil, or more, within 2,000 mi (3 200 km). The following list indicates the
conditions and corrections of excessive oil consumption:

^ An improperly rea oil level indicator (dipstick)


- Inspect the oil level while the vehicle is parked on a level surface.
- Allow adequate drain-down time.
^ Improper oil viscosity
- Use the recommended SAE viscosity for prevailing temperatures.
- Refer to the proper oil viscosity specifications.
^ Continuous high-speed driving
^ Severe hauling, such as a trailer. This causes decreased oil mileage.
^ A malfunctioning crankcase ventilation system
^ External oil leaks
- Tighten the bolts, as needed.
- Replace the gaskets and seals, as needed.
^ Worn or omitted valve guides and/or valve stem seals
- Ream the guides.
- Install oversized service valves and/or new valve stem seals.
^ Broken or worn piston rings
^ Improperly installed or unseated piston rings
^ Improperly installed or improperly fitted piston
^ Plugged cylinder head gasket oil drain holes
^ Damaged intake gaskets
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 1
Chevrolet Venture V6-3.4L VIN E 38
Engine: Testing and Inspection
Oil Leak Diagnosis
^ Tools Required
- J 28428-E High Intensity Black Light

You may repair most fluid leaks by first visually locating the leak, repairing or replacing the component, or by resealing the gasket surface. Once
the leak is identified, determine the cause of the leak. Repair the leak and the cause of leak.

Locating and Identifying the Leak


Use the visual inspection method in order to determine if the leaking fluid is one of the following items:
^ Engine oil
^ Transmission fluid
^ Power steering fluid
^ Brake fluid
^ Some other fluid

Visual Inspection Method


Complete the following steps in order to perform the visual inspection method:
1. Bring the vehicle to normal operating temperature.
2. Park the vehicle over a large sheet of paper, or other clean surface.
3. Wait several minutes, then inspect for dripping fluids.
4. Identify the type of fluid, and the approximate location of the leak.
5. Visually inspect the suspected area. Use a small mirror if necessary.
6. Inspect for leaks at sealing surfaces, fittings, or from cracked or damaged components.
7. If you cannot locate the leak, perform the following steps:
7.1. Completely clean the entire engine and surrounding components.
7.2. Operate the vehicle for several miles at normal operation temperature and at varying speeds.
7.3. Park the vehicle over a large sheet of paper, or other clean surface.
7.4. Wait several minutes, then inspect for dripping fluids.
7.5. Identify the type of fluid, and the approximate location of the leak.
7.6. Visually inspect the suspected area. Use a small mirror if necessary.
7.7. Refer to Possible Causes for Leaks.
8. If you still cannot locate the leak, use the powder method or the black light and dye method.

Powder Method
1. Completely clean the entire engine and surrounding components.
2. Apply an aerosol-type powder (baby powder, foot powder, etc.) to the suspected area.
3. Operate the vehicle for several miles at normal operation temperature and at varying speeds.
4. Identify the type of fluid, and the approximate location of the leak, from the discolorations in the powder surface.
5. Visually inspect the suspected area. Use a small mirror to assist in looking at hard to see areas. Refer to Possible Causes for Leaks if
necessary.

Black Light and Dye Method


A dye and light kit is available for finding leaks.
1. Use the J 28428-E or the equivalent. Refer to the manufacturer's instructions when using the tool.
2. Visually inspect the suspected area. Use a small mirror if necessary. Refer to Possible Causes for Leaks if necessary.

Possible Causes for Leaks


Inspect the vehicle for the following conditions:
^ Higher than recommended fluid levels
^ Higher than recommended fluid pressures
^ Plugged or malfunctioning fluid filters or pressure bypass valves
^ Plugged or malfunctioning engine ventilation system
^ Improperly tightened or damaged fasteners
^ Cracked or porous components
^ Improper sealants or gaskets where required
^ Improper sealant or gasket installation
^ Damaged or worn gaskets or seals
^ Damaged or worn sealing surfaces
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 1
Chevrolet Venture V6-3.4L VIN E 39
Engine: Removal and Replacement

Engine Replacement
Removal Procedure

1. Disconnect the battery ground (negative) cable. Refer to Battery Negative Cable Disconnect/Connect Procedure.
2. Remove the throttle body air inlet duct. Refer to Air Filter Element Replacement in Computers and Controls.
3. Remove the cruise control cable from the engine and reposition the cable away from the engine. Refer to Cruise Control Cable Replacement
in Cruise Control.

Caution: In order to avoid possible injury or vehicle damage, always replace the accelerator control cable with a NEW cable
whenever you remove the engine from the vehicle.
In order to avoid cruise control cable damage, position the cable out of the way while you remove or install the engine. Do not pry or
lean against the cruise control cable and do not kink the cable. You must replace a damaged cable.

4. Remove the accelerator control cable from the engine and reposition the cable away from the engine. Refer to Accelerator Controls Cable
Replacement in Computers and Controls.
5. Drain the engine coolant from the cooling system. Refer to Draining and Filling Cooling System in Cooling System.
6. Disconnect the radiator hoses from the engine. Refer to Radiator Hose Replacement - Inlet and Radiator Hose Replacement - Outlet in
Cooling System.
7. Disconnect the heater hoses from the engine. Refer to Heater Hose Replacement - Inlet and Heater Hose Replacement - Outlet in Heating and
Air Conditioning.
8. Remove the engine mount struts. Refer to Engine Mount Strut Replacement (Left) or Engine Mount Strut Replacement (Right).

Important: Relief the fuel pressure. Refer to Fuel Pressure Relief Procedure in Computers and Controls.

9. Disconnect the fuel lines from the fuel rail. Refer to Fuel Hose/Pipes Replacement (Engine Compartment) (Engine pipes) in Computers and
Controls.
10. Remove the engine wiring harness connectors.
11. Remove the vacuum hoses from the engine.
12. Remove the vacuum brake booster hose. Refer to Vacuum Brake Booster Hose Replacement in Brakes and Traction Control.
13. Remove the automatic transaxle range selector cable. Refer to Automatic Transmission Range Selector Cable Replacement in Transmission
and Drivetrain.
14. Raise and support the vehicle. Refer to Vehicle Lifting.
15. Drain the engine oil. Refer to Engine Oil and Oil Filter Replacement (Without Oil Cooler) or Engine Oil and Oil Filter Replacement (With
Oil Cooler).
16. Remove the wiring harness grounds.
17. Remove the three-way catalytic converter exhaust pipe from the engine right side exhaust manifold. Refer to Catalytic Converter
Replacement in Powertrain Management.
18. Remove the front tires and wheels. Refer to Tire and Wheel Removal and Installation.
19. Remove the engine splash shields. Refer to Splash Shield Replacement - Engine in Body and Frame.
20. Remove the stabilizer shaft links from the lower control arms. Refer to Stabilizer Shaft Link Replacement in Steering and Suspension.
21. Remove the tie rod ends from the steering knuckles. Refer to Steering Knuckle Replacement in Steering and Suspension.
22. Remove the lower ball joints from the knuckles. Refer to Lower Ball Joint Replacement in Steering and Suspension.
23. Remove the transaxle cooler lines and bracket from the transaxle. Refer to Automatic Transmission Oil Cooler Hose Replacement in
Transmission and Drivetrain.
24. Disconnect the drive axles from the transaxle. Refer to Wheel Drive Shafts Replacement in Transmission and Drivetrain.
25. Secure the drive axles to the steering knuckle/struts.

Caution: Failure to disconnect the intermediate shaft from the rack and pinion steering gear stub shaft can result in damage to the
steering gear and/or intermediate shaft. This damage may cause loss of steering control which could result in an accident and
possible personal injury

26. Remove the intermediate shaft from the steering gear. Refer to Lower/Upper Intermediate Steering Shaft Replacement in Steering and
Suspension.
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 2
Chevrolet Venture V6-3.4L VIN E 40

27. Lower the vehicle until the frame contacts the transaxle table.
28. Remove the frame bolts. Refer to Frame Replacement in Body and Frame.
29. Raise the vehicle in order to separate the powertrain/frame from the vehicle.

30. Remove the engine-to-transaxle bolts (3, 4, 5 and 6) and studs (1 and 2).
31. Remove the engine flywheel to torque converter bolts. Refer to Flywheel to Torque Converter Bolts in Transmission and Drivetrain.
32. Remove the engine from the transaxle/frame to the engine stand.

Installation Procedure

1. Install the engine to the transaxle/frame from the engine stand.

Notice: Refer to Fastener Notice in Service Precautions.

2. Install the engine-to-transaxle bolts (3, 4, 5 and 6) and studs (1 and 2).
^ Tighten the engine-to-transaxle bolts (3, 4, 5 and 6) and studs (11 and 2) to 75 Nm (55 ft. lbs.).
3. Install the engine flywheel to torque converter bolts. Refer to Flywheel to Torque Converter Bolts in Transmission and Drivetrain.
4. Position the transaxle table with the powertrain/frame under the vehicle.
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 3
Chevrolet Venture V6-3.4L VIN E 41

5. Lower the vehicle until the frame contacts the transaxle table.
6. Install the NEW frame bolts. Refer to Frame Replacement in Body and Frame.
7. Raise and support the vehicle. Refer to Vehicle Lifting.
8. Remove the transaxle table.

Caution: When installing the intermediate shaft make sure that the shaft is seated prior to pinch bolt installation. If the pinch bolt is
inserted into the coupling before shaft installation, the two mating shafts may disengage. Disengagement of the two mating shafts will
cause loss of steering control which could result in personal injury.

9. Install the intermediate shaft to steering gear. Refer to Lower/Upper Intermediate Steering Shaft Replacement in Steering and Suspension.
10. Install the drive axles to the transaxle. Refer to Wheel Drive Shafts Replacement in Transmission and Drivetrain.
11. Install the transaxle cooler lines and bracket to the transaxle. Refer to Automatic Transmission Oil Cooler Hose Replacement in Transmission
and Drivetrain.
12. Install the lower ball joints to the knuckles. Refer to Lower Ball Joint Replacement in Steering and Suspension.
13. Install the tie rod ends to the steering knuckles. Refer to Steering Knuckle Replacement in Steering and Suspension.
14. Install the stabilizer shaft links to the lower control arms. Refer to Stabilizer Shaft Link Replacement in Steering and Suspension.
15. Install the inner fender splash shield. Refer to Splash Shield Replacement - Engine in Body and Frame.
16. Install the front tires and wheels. Refer to Tire and Wheel Removal and Installation in Steering and Suspension.
17. Install the three-way catalytic converter exhaust pipe to the engine right side exhaust manifold. Refer to Catalytic Converter Replacement in
Powertrain Management.
18. Install the wiring harness grounds.
19. Lower the vehicle
20. Install the automatic transaxle range selector cable. Refer to Automatic Transmission Range Selector Cable Replacement in Transmission and
Drivetrain.
21. Install the vacuum brake booster hose. Refer to Vacuum Brake Booster Hose Replacement in Brakes and Traction Control.
22. Install the vacuum hoses to the engine.
23. Install the engine wiring harness connectors.
24. Install the fuel lines to the fuel rail. Refer to Fuel Hose/Pipes Replacement (Engine Compartment) (Engine pipes) in Computers and Controls.
25. Install the throttle body bracket and cables. Refer to Accelerator Controls Cable Replacement in Computers and Controls.
26. Install the engine mount strut. Refer to Engine Mount Strut Replacement (Left) or Engine Mount Strut Replacement (Right).
27. Connect the heater hoses to the engine. Refer to Heater Hose Replacement - Inlet and Heater Hose Replacement - Outlet in Heating and Air
Conditioning.
28. Connect the radiator hoses to the engine. Refer to Radiator Hose Replacement - Inlet and Radiator Hose Replacement - Outlet in Cooling
System.
29. Fill the cooling system with engine coolant. Refer to Draining and Filling Cooling System in Cooling System.
30. Adjust the transaxle fluid level. Refer to the following information:
^ Transmission Fluid Checking Procedure in Transmission and Drivetrain
^ Capacities - Approximate Fluid
^ Fluid and Lubricant Recommendations
31. Fill the engine with oil. Refer to Engine Oil and Oil Filter Replacement (Without Oil Cooler) or Engine Oil and Oil Filter Replacement (With
Oil Cooler).

Caution: In order to avoid possible injury or vehicle damage, always replace the accelerator control cable with a NEW cable
whenever you remove the engine from the vehicle.
In order to avoid cruise control cable damage, position the cable out of the way while you remove or install the engine. Do not pry or
lean against the cruise control cable and do not kink the cable. You must replace a damaged cable.

32. Install the accelerator control cable to the engine. Refer to Accelerator Controls Cable Replacement in Computers and Controls.
33. Install the cruise control cable to the engine. Refer to Cruise Control Cable Replacement in Cruise Control.
34. Install the throttle body air inlet duct. Refer to Air Filter Element Replacement in Computers and Controls.
35. Connect the battery ground (negative) cable. Refer to Battery Negative Cable Disconnect/Connect Procedure.
36. Perform the CKP system variation learn procedure. Refer to CKP System Variation Learn Procedure in Computers and Controls.
37. Inspect for proper fluid levels and possible fluid leaks.
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 4
Chevrolet Venture V6-3.4L VIN E 42

Engine Support Fixture


Installation Procedure

^ Tools Required
- J 28467-B Universal Engine Support Fixture
- J 28467-500 Engine Support Fixture

1. Remove the right side engine mount strut. Refer to Engine Mount Strut Replacement (Left) or Engine Mount Strut Replacement (Right).
2. Install the J 28467-500.

3. Install the spreader bar to the engine mount strut bracket.

4. Install the spreader bar to the engine right side engine lift hook.
5. Install the J 28467-6A.
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 5
Chevrolet Venture V6-3.4L VIN E 43

6. Install the J 28467-7A to the engine left side engine lift hook.
7. Install the J 28467-34.
8. Install the J 28467-6A.

9. Install the J 28467-8A to the spreader bar.


10. Install the J 28467-34.

11. The engine support fixture upper portion installed.

Important: Perform the following steps only if you are disconnecting both of the powertrain mounts from the frame or the powertrain.

12. Raise and support the vehicle. Refer to Vehicle Lifting.

Caution: The utility straps MUST be installed in order to prevent forward movement of the powertrain. If the utility straps are not
installed, the powertrain will move which may cause personal injury and vehicle damage.
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 6
Chevrolet Venture V6-3.4L VIN E 44

13. Install the J 28467-500UPD to the engine.

14. Install the J 28467-500UPD opposite end to the underbody rail.

15. Install the OTHER J 28467-500UPD to the transaxle.


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 7
Chevrolet Venture V6-3.4L VIN E 45

16. Install the J 28467-500UPD opposite end to the underbody rail.


17. Tighten both of the J 28467-500UPD utility straps in order to prevent forward movement of the powertrain.

Removal Procedure

1. Remove both of the J 28467-500UPD.


2. Lower the vehicle.
3. Remove the J 28467-34.
4. Remove the J 28467-7A.
5. Remove the J 28467-6A.
6. Remove the J 28467-34.
7. Remove the J 28467-8A.
8. Remove the J 28467-6A.
9. Remove the J 28467-500.
10. Install the right side engine mount strut. Refer to Engine Mount Strut Replacement (Left) or Engine Mount Strut Replacement (Right).

Rotating the Engine For Service Access


ROTATING THE ENGINE FOR SERVICE ACCESS.

^ Tools Required
- J 41131 Engine Tilt Strap

1. Remove the throttle body air inlet duct. See: Tune-up and Engine Performance Checks/Air Cleaner Housing/Air Filter Element/Service and
Repair
2. Set the park brake.
3. Shift the transaxle into Neutral.
4. Remove the engine mount strut bolts. Swing the engine mount struts aside. Refer to Engine Mount Strut Replacement (Left) or Engine Mount
Strut Replacement (Right).

5. Install the J 41131.


6. Pull on the engine in order to rotate the engine forward.
7. Tighten the J 41131.
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 1
Chevrolet Venture V6-3.4L VIN E 46
Engine: Tools and Equipment
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 2
Chevrolet Venture V6-3.4L VIN E 47
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 3
Chevrolet Venture V6-3.4L VIN E 48
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 1
Chevrolet Venture V6-3.4L VIN E 49
Engine: Overhaul

Overhaul Procedure Steps


ENGINE OVERHAUL
In order to overhaul, follow the sequence below.

1. Draining Fluids and Oil Filter Removal


2. Crankshaft Balancer Removal
3. Engine Flywheel Removal
4. Drive Belt Tensioner Removal
5. Generator and Engine Lift Front Bracket Removal
6. Engine Mount Strut and Engine Lift Bracket Removal
7. Engine Mount Strut and A/C Compressor Bracket Removal
8. Oil Level Indicator and Tube Removal
9. Oil Filter Adapter Removal
10. Valve Rocker Arm Cover Removal
11. Intake Manifold Removal
12. Water Outlet Removal
13. Exhaust Crossover Removal
14. Exhaust Manifold Removal
15. Valve Rocker Arm and Push Rod Removal
16. Valve Lifter Removal
17. Water Pump Removal
18. Oil Pan Removal
19. Oil Pump Removal
20. Oil Pump Drive Removal
21. Crankshaft Front Oil Seal Removal
22. Engine Front Cover Removal
23. Timing Chain and Sprockets Removal
24. Cylinder Head Removal
25. Camshaft Removal
26. Piston, Connecting Rod, and Bearing Removal
27. Crankshaft Rear Oil Seal Removal
28. Crankshaft and Bearing Removal
29. Engine Block Disassemble
30. Engine Block Clean and Inspect
31. Cylinder Boring and Honing
32. Engine Block Assemble
33. Crankshaft and Bearing Clean and Inspect
34. Crankshaft Balancer Clean and Inspect
35. Engine Flywheel Clean and Inspect
36. Piston and Connecting Rod Disassemble
37. Piston, Connecting Rod, and Bearing Clean and Inspect
38. Piston Selection
39. Piston and Connecting Rod Assemble
40. Camshaft Bearing Removal
41. Camshaft and Bearings Clean and Inspect
42. Camshaft Bearing Installation
43. Timing Chain and Sprocket Clean and Inspect
44. Valve Lifters Clean and Inspect
45. Valve Rocker Arm and Push Rod Clean and Inspect
46. Cylinder Head Disassemble
47. Cylinder Head Clean and Inspect
48. Valve Guide Reaming, and Valve and Seat Grinding
49. Cylinder Head Assemble
50. Oil Pump Disassemble
51. Oil Pump Clean and Inspect
52. Oil Pump Assemble
53. Engine Front Cover Clean and Inspect
54. Valve Rocker Arm Cover Clean and Inspect
55. Oil Pan Clean and Inspect
56. Intake Manifold Clean and Inspect
57. Exhaust Manifold Clean and Inspect
58. Water Pump Clean and Inspect
59. Thread Repair
60. Service Prior to Assembly
61. Crankshaft and Bearing Installation
62. Crankshaft Rear Oil Seal Installation
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 2
Chevrolet Venture V6-3.4L VIN E 50
63. Piston, Connecting Rod, and Bearing Installation
64. Camshaft Installation
65. Timing Chain and Sprockets Installation
66. Engine Front Cover Installation
67. Crankshaft Front Oil Seal Installation
68. Oil Pump Drive Installation
69. Oil Pump Installation
70. Oil Pan Installation
71. Cylinder Head Installation
72. Water Pump Installation
73. Valve Lifter Installation
74. Valve Rocker Arm and Push Rod Installation
75. Exhaust Manifold Installation
76. Exhaust Crossover Installation
77. Intake Manifold Installation
78. Valve Rocker Arm Cover Installation
79. Water Outlet Installation
80. Oil Filter Adapter Installation
81. Oil Level Indicator and Tube Installation
82. Generator and Engine Lift Front Bracket Installation
83. Engine Mount Strut and Engine Lift Bracket Installation
84. Engine Mount Strut and A/C Compressor Bracket Installation
85. Drive Belt Tensioner Installation
86. Engine Flywheel Installation
87. Crankshaft Balancer Installation
1. Draining Fluids and Oil Filter Removal

1. Remove the oil pan drain plug.


2. Drain the engine oil.

3. Remove the oil filter.


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 3
Chevrolet Venture V6-3.4L VIN E 51

4. Remove the coolant drain plug from the left side.

5. Remove the coolant drain plug from the right side.


6. Drain the coolant.

2. Crankshaft Balancer Removal


^ Tools Required
- J 24420-C Crankshaft Balancer Puller

1. Remove the crankshaft balancer retaining bolt and washer.


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 4
Chevrolet Venture V6-3.4L VIN E 52

2. Remove the crankshaft balancer using the J 24420-C.

3. Engine Flywheel Removal

1. Remove the flywheel bolts.


2. Remove the flywheel retainer.
3. Remove the flywheel.

4. Drive Belt Tensioner Removal

1. Remove the drive belt tensioner bolt.


2. Remove the drive belt tensioner.

5. Generator and Engine Lift Front Bracket Removal


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 5
Chevrolet Venture V6-3.4L VIN E 53

1. Remove the generator bracket bolts (1 - 3).


2. Remove the generator bracket.
3. Remove the front engine lift hook.

6. Engine Mount Strut and Engine Lift Bracket Removal

1. Remove the engine mount strut and A/C compressor bracket bolts.
2. Remove the engine mount strut and A/C compressor bracket.

7. Engine Mount Strut and A/C Compressor Bracket Removal

1. Remove the engine mount strut and lift bracket bolts.


2. Remove the engine mount strut and lift bracket.

8. Oil Level Indicator and Tube Removal


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 6
Chevrolet Venture V6-3.4L VIN E 54

1. Remove the thermostat bypass pipe to throttle body nut (2).


2. Remove the thermostat bypass pipe to throttle body hose clamps (1).
3. Remove the thermostat bypass pipe to engine front cover bolt (4).
4. Remove the thermostat bypass pipe to cylinder head nut (3).
5. Remove the thermostat bypass pipe hose clamps (5).

6. Remove the thermostat bypass pipe hose.


7. Remove the thermostat bypass pipe.

8. Remove the oil level indicator and oil level indicator tube.

9. Oil Filter Adapter Removal


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 7
Chevrolet Venture V6-3.4L VIN E 55

1. Remove the oil filter bypass hole plug.

Important: Do not remove the oil filter fitting unless replacement or repair is needed.

2. Remove the oil filter fitting, if necessary.


3. Remove the oil filter bypass valve, by prying out with a suitable tool.

Left Valve Rocker Arm Cover

1. Remove the spark plug wires.


2. Remove the electronic ignition control module nuts and bolts.
3. Remove the electronic ignition control module.

4. Disconnect the vacuum lines from the upper intake manifold.


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 8
Chevrolet Venture V6-3.4L VIN E 56

5. Remove the valve rocker arm cover bolts.


6. Remove the valve rocker arm cover and gasket.

Right Valve Rocker Arm Cover

1. Remove the valve rocker arm cover bolts.


2. Remove the valve rocker arm cover and gasket.

Upper Intake Manifold

1. Disconnect the MAP sensor electrical connector.


2. Remove the MAP sensor screws.
3. Remove the MAP sensor.
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 9
Chevrolet Venture V6-3.4L VIN E 57

4. Remove the EGR valve pipe from the exhaust manifold.


5. Remove the EGR valve bolts.
6. Remove the EGR valve and gasket.
7. Remove the EGR valve pipe and gasket.

8. Remove the upper intake manifold.


9. manifold studs and bolts.
10. Remove the upper intake manifold gaskets.

11. Remove the upper intake manifold gaskets.

Lower Intake Manifold


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 10
Chevrolet Venture V6-3.4L VIN E 58

1. Remove the fuel feed and return pipe retaining clip bolt.
2. Remove the fuel feed and return pipe retaining clip.

3. Remove the fuel injector rail bolts.


4. Remove the fuel injector rail assembly.

5. Remove the heater inlet pipe nut.


6. Remove the heater inlet pipe.
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 11
Chevrolet Venture V6-3.4L VIN E 59

7. Remove the lower intake manifold bolts.


8. Remove the lower intake manifold.

12. Water Outlet Removal

1. Remove the water outlet bolts.


2. Remove the water outlet.
3. Remove the water outlet gasket.

4. Remove the thermostat.

13. Exhaust Crossover Removal


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 12
Chevrolet Venture V6-3.4L VIN E 60

1. Remove the exhaust crossover pipe heat shield bolts.


2. Remove the exhaust crossover pipe heat shield.

3. Remove the exhaust crossover pipe nuts.


4. Remove the exhaust crossover pipe.

Left Exhaust Manifold

1. Remove the exhaust manifold heat shield bolts.


2. Remove the exhaust manifold heat shield.
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 13
Chevrolet Venture V6-3.4L VIN E 61

3. Remove the exhaust manifold nuts.


4. Remove the exhaust manifold.
5. Remove the exhaust manifold gasket.

Right Exhaust Manifold

1. Remove the heated oxygen sensor.

2. Remove the exhaust manifold heat shield bolts.


3. Remove the exhaust manifold heat shields.
4. Remove the right side spark plugs.
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 14
Chevrolet Venture V6-3.4L VIN E 62

5. Remove the exhaust manifold nuts.


6. Remove the exhaust manifold.
7. Remove the exhaust manifold gasket.

15. Valve Rocker Arm and Push Rod Removal

1. Remove the valve rocker arm bolts.

Important: Place the valve train components in a rack in order to ensure that the components are installed in the same location from which
they were removed.

2. Remove the valve rocker arms.

3. Remove the push rods.


^ The intake push rods measure 144.18 mm (5.68 inch).
^ The exhaust push rods measure 152.51 mm (6.0 inch).
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 15
Chevrolet Venture V6-3.4L VIN E 63

4. Remove the intake manifold gaskets.

16. Valve Lifter Removal

1. Remove the valve lifter guide bolts.


2. Remove the valve lifter guides.

Important: Once removed, place the valve lifters in an organized order so the valve lifters can be installed into the original locations.

3. Remove the valve lifters.

17. Water Pump Removal

1. Remove the water pump pulley bolts.


2. Remove the water pump pulley.
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 16
Chevrolet Venture V6-3.4L VIN E 64

3. Remove the water pump bolts.


4. Remove the water pump.
5. Remove the water pump gasket.

18. Oil Pan Removal

1. Remove the oil pan side bolts.


2. Remove the oil pan bolts.
3. Remove the oil pan.
4. Remove the oil pan gasket.

19. Oil Pump Removal

1. Remove the oil pump bolt.


2. Remove the oil pump and oil pump drive shaft.
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 17
Chevrolet Venture V6-3.4L VIN E 65

3. Remove the crankshaft oil deflector nuts.


4. Remove the crankshaft oil deflector.

20. Oil Pump Drive Removal

1. Remove the oil pump drive clamp bolt.


2. Remove the oil pump drive clamp.
3. Remove the oil pump drive.

21. Crankshaft Front Oil Seal Removal

Pry out the crankshaft front oil seal using a suitable tool. Use care not to damage the engine front cover or the crankshaft.

22. Engine Front Cover Removal


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 18
Chevrolet Venture V6-3.4L VIN E 66

1. Remove the engine front cover bolts (1), (2), and (3).
2. Remove the engine front cover.
3. Remove the engine front cover gasket.

23. Timing Chain and Sprockets Removal


^ Tools Required
- J 5825-A Crankshaft Sprocket Puller

1. Remove the camshaft sprocket bolt.


2. Remove the camshaft sprocket and timing chain.

3. Remove the crankshaft sprocket. Use the J 5825-A.


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 19
Chevrolet Venture V6-3.4L VIN E 67

4. Remove the timing chain dampener bolts.


5. Remove the timing chain dampener.

24. Cylinder Head Removal - Left and Right

1. Remove the cylinder head bolts.


2. Remove the cylinder head.

3. Remove the cylinder head gasket.


4. Remove the dowel pins (cylinder head locator) (if required).

25. Camshaft Removal


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 20
Chevrolet Venture V6-3.4L VIN E 68

1. Remove the camshaft thrust plate screws.


2. Remove the camshaft thrust plate.

Notice: All camshaft journals are the same diameter, so care must be used in removing or installing the camshaft to avoid damage to the
camshaft bearings.

3. Complete the following steps in order to remove the camshaft:


3.1. Install a large screwdriver in the camshaft bolt hole. Do not damage the threads.
3.2. Carefully rotate and pull the camshaft out of the camshaft bearings.

26. Piston, Connecting Rod, and Bearing Removal


^ Tools Required
- J 24270 Ridge Reamer

1. Mark the piston with the number of the cylinder from which the piston is being removed.
2. Mark the connecting rod and the connecting rod cap in order to ensure correct assembly.

Notice: If there is a pronounced ridge at the top of the piston travel, the ridge must be removed with a ridge reamer before the piston and
connecting rod assembly are removed. Applying force may break the piston rings or damage the piston.
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 21
Chevrolet Venture V6-3.4L VIN E 69

3. Use the J 24270 in order to remove the cylinder bore ring ridge. Complete the following steps:
3.1. Turn the crankshaft until the piston is at the bottom of the stroke.
3.2. Cover the piston with a cloth.
3.3. Remove the cylinder ring ridge.
3.4. Turn the crankshaft until the piston is at the top of the stroke.
3.5. Remove the cloth.
3.6. Remove the metal shavings from the cylinder and piston.

4. Remove the connecting rod nuts and cap.


5. Remove the connecting rod cap and bearing half.

Notice: Install thread protector in order to avoid damage to the crankshaft journal.

6. Remove the connecting rod and piston assembly. Push out the assembly using a suitable tool.

27. Crankshaft Rear Oil Seal Removal

1. Remove the crankshaft rear oil seal.

Important: Do not damage the crankshaft or seal bore.

2. Pry out the crankshaft rear oil seal out using a suitable tool.

28. Crankshaft and Bearings Removal


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 22
Chevrolet Venture V6-3.4L VIN E 70

1. Remove the crankshaft main bearing cap bolt and studs.


2. Remove the crankshaft main bearing caps and lower crankshaft main bearing halves.
3. Remove the crankshaft.
4. Remove the upper crankshaft main bearing halves.

29. Engine Block Disassemble

1. Remove the camshaft rear bearing hole plug.

2. Remove the rear oil gallery plugs (1, 2, 3).


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 23
Chevrolet Venture V6-3.4L VIN E 71

3. Remove the front oil gallery plugs (1, 2).


4. Remove all of the remaining engine block plugs.

5. Remove the knock sensor.

6. Remove the crankshaft position sensor stud.


7. Remove the crankshaft position sensor from the side of the engine block.
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 24
Chevrolet Venture V6-3.4L VIN E 72

8. Remove the camshaft position sensor bolt.


9. Remove the camshaft position sensor.

10. Remove the engine oil pressure switch.

30. Engine Block Clean and Inspect


^ Tools Required
- J 8001 Dial Indicator Set
- J 8087 Cylinder Bore Gage

1. Clean the sealing material from the gasket mating surfaces.


2. Boil the engine block in caustic solution.
3. Flush the engine block with clean water or steam.
4. Clean the oil passages.
5. Clean the blind holes.
6. Spray the cylinder bores and the machined surfaces with engine oil.
7. Inspect the threaded holes.
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 25
Chevrolet Venture V6-3.4L VIN E 73
8. Clean the holes with a tap. Drill out the holes and install thread inserts, as needed.

9. Use a straight edge and a feeler gauge in order to test the deck surface for flatness. Carefully machine minor irregularities. Replace the block
if more than 0.25 mm (0.010 inch) must be removed.
10. Inspect the oil pan rail for nicks. Inspect the front cover attaching area for nicks. Use a flat mill file in order to remove any nicks.

11. Inspect the mating surfaces of the transmission case.

Notice: A broken flywheel may result if the transmission case mating surface is not flat.

12. Use the following procedure in order to measure the engine block flange runout at the 6 mounting bolt hole bosses:
12.1. Temporarily install the crankshaft. Measure the crankshaft flange runout.
12.2. Hold the J 8001 gauge plate flat against the crankshaft flange.
12.3. Place the dial indicator stem on the transmission mounting bolt hole boss. Set the indicator to 0.
12.4. Record the readings obtained from all of the bolt hole bosses. The measurements should not vary more than 0.25 mm (0.010 inch).
12.5. Retest the crankshaft flange runout if the readings vary more than 0.25 mm (0.010 inch). If the crankshaft flange runout is within the
specification, replace the engine block.

Important: Perform the following inspections, and reconditioning (if necessary), with the crankshaft main bearing caps installed and
tightened to specification.

13. Inspect the crankshaft main bearing bores. Use the J 8087 in order to measure the bearing bore concentricity and alignment at the following
locations:
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 26
Chevrolet Venture V6-3.4L VIN E 74
^ The camshaft
^ The crankshaft
14. Replace the engine block if the bores are out of specification.

15. Use the J 8087 in order to inspect the cylinder bores. Inspect the bores for the following conditions:
^ Wear
^ Taper
^ Runout
^ Ridging

Important: If the bore is worn beyond the limits, refit the bore with 0.5 mm oversized pistons.

16. Leave sufficient material in order to allow honing when fitting the piston.

31. Cylinder Boring and Honing


Boring Procedure

1. Before honing or boring, measure all of the new pistons. Select the smallest piston for the piston fitting. Slightly varied pistons in a set may
provide correction, if the first piston is too loosely fitted.
2. Before using any type of boring bar, file the top of the engine block to remove any dirt or burrs. If the cylinder block is not straight, the
boring bar may be tilted, causing the bored cylinder wall to have incorrect right angles to the crankshaft.
3. Carefully follow the instructions furnished by the manufacturer regarding use of equipment.
4. Install all crankshaft main bearing caps to specification when boring cylinders. Cover or tape the crankshaft bearings and other internal parts
to protect these parts during the boring or honing operation.
5. Leave 0.03 mm (0.001 inch) on the diameter for finish honing when performing the final cut with a boring bar. Carefully perform the honing
and boring operation to maintain the specified clearances between pistons, rings, and cylinder bores.

Honing Procedure
1. Follow the manufacturer's recommendations for use, cleaning, and lubrication when honing the cylinders. Use only clean, sharp stones of the
proper grade for the amount of material to be removed. Dull, dirty stones cut unevenly and generate excessive heat. When using coarse or
medium-grade stones, leave sufficient metal so all stone marks may be removed with the fine stones used for finishing to provide the proper
clearance.
2. During the honing operation, thoroughly clean the cylinder bore. Check for the correct piston fit.
3. Make full strokes in the cylinder to eliminate taper. Repeatedly check the measurement at the top, the middle, and the bottom of the cylinder
bore.
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 27
Chevrolet Venture V6-3.4L VIN E 75

Notice: Handle the pistons with care. Do not force the pistons through the cylinder until you hone the cylinder to the correct size. The piston
can be distorted through careless handling.

4. When finish honing a cylinder bore to fit a piston, move the hone up and down at a sufficient speed to obtain a fine and uniform surface
finish in a cross hatch pattern.
5. The finish marks should be clean but not sharp. The finish marks should be free from imbedded particles and torn or folded metal.
6. Determine the finish hone cylinder measurement by measuring the piston to be installed, and by adding the average of the clearance
specification. Measure the block and the piston at normal room temperature.
7. True up the refinished cylinder bores. Final hone each cylinder bore to remove all stone or cutter marks.
8. After final honing and before the piston is checked for fit, clean the bores with hot water and detergent. Scrub the bores with a stiff bristle
brush and rinse the bores thoroughly with hot water. Do not allow any abrasive material to remain in the cylinder bores. This abrasive
material will wear the new rings, the cylinder bores, and the bearings lubricated by the contaminated oil. After washing dry the bore.
9. Permanently mark the piston for the cylinder to which the piston has been fitted.
10. Apply clean engine oil to each bore to prevent rusting.

32. Engine Block Assemble

1. Apply sealer GM P/N 12346004 or the equivalent to the oil pressure switch threads.

Notice: Refer to Fastener Notice in Service Precautions.

2. Install the engine oil pressure switch.


^ Tighten the engine oil pressure switch to 13 Nm (115 inch lbs.).

3. Install the camshaft position sensor.


4. Install the camshaft position sensor bolt.
^ Tighten the camshaft position sensor bolt to 10 Nm (89 inch lbs.).
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 28
Chevrolet Venture V6-3.4L VIN E 76

5. Install the crankshaft position sensor into the side of the engine block.
6. Apply threadlock GM P/N 12345382 or the equivalent to the position sensor stud threads.
7. Install the crankshaft position sensor stud.
^ Tighten the crankshaft position sensor stud to 11 Nm (98 inch lbs.).

8. Apply sealer GM P/N 12346004 or the equivalent to the knock sensor threads.
9. Install the knock sensor.
^ Tighten the knock sensor to 19 Nm (14 ft. lbs.).

10. Apply sealer GM P/N 12346004 or the equivalent to the front oil gallery plug threads (1 and 2).
11. Install the front oil gallery plug (1).
^ Tighten the oil gallery plug (1) to 19 Nm (14 ft. lbs.).
12. Install the front oil gallery plug (2).
^ Tighten the oil gallery plug (2) to 33 Nm (24 ft. lbs.).
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 29
Chevrolet Venture V6-3.4L VIN E 77

13. Apply sealer GM P/N 12346004 or the equivalent to the rear oil gallery plug threads (1 and 4).
14. Install the rear oil gallery plugs (1 and 4).
^ Tighten the oil gallery plugs (1 and 4) to 19 Nm (14 ft. lbs.).
15. Install the rear oil gallery plugs (2 and 3).
^ Tighten the oil gallery plugs (2 and 3) to 33 Nm (24 ft. lbs.).
16. Apply sealer GM P/N 12346004 or the equivalent to the engine block plugs.
17. Install the remaining engine block plugs.

18. Apply sealant GM P/N 12346004 or the equivalent to the coolant drain plug threads.
19. Install the left coolant drain plug.
^ Tighten the coolant drain plug to 19 Nm (14 ft. lbs.).

20. Apply sealant GM P/N 12346004 or the equivalent to the coolant drain plug threads.
21. Install the right coolant drain plug.
^ Tighten the coolant drain plug to 19 Nm (14 ft. lbs.).

33. Crankshaft and Bearings Clean and Inspect


^ Tools Required
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 30
Chevrolet Venture V6-3.4L VIN E 78
- J 8087 Cylinder Bore Gage
- J 36660-A Torque Angle Meter

1. Clean the crankshaft of the following elements:


^ Oil
^ Sludge
^ Carbon
2. Inspect the crankshaft oil passages for obstructions.

3. Inspect the crankshaft keyway for the following conditions:


^ A worn crankshaft key (1)
^ A worn crankshaft keyway (2)
4. Inspect the crankshaft threads (3) for damage.

Important: If cracks, severe gouges or burned spots are found, replace the crankshaft. Remove slight roughness using a fine polishing cloth
soaked in clean engine oil. Remove any burrs using a fine oil stone.

5. Inspect the crankshaft bearing journals and the crankshaft thrust surfaces for the following conditions:
^ Wear without any grooves or scratches (1)
^ Grooves or scoring (2)
^ Scratches or excessive wear (3)
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 31
Chevrolet Venture V6-3.4L VIN E 79
^ Pitting or embedded bearing material (4)
Inspect the corresponding crankshaft bearing inserts for embedded material and determine the source of the material.
^ Overheating (discoloration)

Notice: Do not scrape, shim, or file bearing inserts. If the bearing surface of the insert is touched with bare fingers, the skin oil and acids will
etch the bearing surface.

6. The crankshaft bearings are the precision insert type.


7. Inspect the outer surfaces of the crankshaft bearings for the following conditions:
^ Wear - surface wear indicates either movement of the insert, or high spots in the surrounding material (spot wear).
^ Overheating or discoloration
^ Looseness or rotation indicated by flattened tangs and wear grooves

Important: Note the location of the crankshaft main bearing high spots. If the spots are not in line, the crankshaft is bent. Replace the
crankshaft.

8. Inspect the crankshaft main bearings for craters or pockets. Flattened sections on the crankshaft bearing halves also indicate fatigue.
9. Inspect the thrust surfaces of the main thrust bearing for the following conditions:
^ Wear
^ Grooving - Grooves are caused by irregularities of the crankshaft thrust surface.

10. Inspect the crankshaft bearings for excessive scoring or discoloration.


11. Inspect the crankshaft main bearings for dirt or imbedded debris.
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 32
Chevrolet Venture V6-3.4L VIN E 80

12. Inspect the crankshaft main bearings for improper seating indicated by bright, polished sections.
13. Inspect the crankshaft bearings for uneven side-to-side wear. This may indicate a bent crankshaft or a tapered bearing journal.

Important: If crankshaft bearing failure is due to conditions other than normal wear, investigate the cause of the condition. Inspect the
crankshaft or connecting rod bearing bores.

14. Inspect the connecting rod bearing bores or crankshaft main bearing bores using the following procedure:
14.1. Tighten the bearing cap to specification.
14.2. Use the J 8087 in order to measure the bearing bore for taper and out-of-round. Record the readings for bearing selection.
14.3. No taper or out-of-round should exist.

Bearing Selection

Measure the bearing clearance to determine the correct replacement bearing insert size. There are two methods to measure bearing clearance.
Method A gives more reliable results and is preferred.
^ Method A yields measurement from which the bearing clearance can be computed.
^ Method B yields the bearing clearance directly. Method B does not give any indication of bearing run-out.

Method A

Important: Do not mix inserts of different nominal size in the same bearing bore.

1. Measure the crankshaft bearing journal diameter with a micrometer in several places, 90 degrees apart. Average the measurements.
2. Measure the crankshaft bearing journal taper and runout.
3. Install the crankshaft bearing inserts. Tighten the bearing cap bolts to specification.
4. Measure the connecting rod inside diameter in the same direction as the length of the rod with an inside micrometer.
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 33
Chevrolet Venture V6-3.4L VIN E 81
5. Measure the crankshaft main bearing inside diameter with an inside micrometer.
6. Select a set of bearing inserts that will produce the desired clearance.
7. If the specified clearances cannot be met, the crankshaft journals must be reconditioned and undersized bearing inserts installed.

Method B

Important: Do not mix inserts of different nominal size in the same bearing bore.

1. Clean the used bearing inserts.


2. Install the used bearing inserts.
3. Place a piece of gaging plastic across the entire bearing width.
4. Install the bearing caps.

Notice: In order to prevent the possibility of cylinder block or crankshaft bearing cap damage, the crankshaft bearing caps are tapped into
the cylinder block cavity using a brass, lead, or a leather mallet before the attaching bolts are installed. Do not use attaching bolts to pull the
crankshaft bearing caps into the seats. Failure to use this process may damage a cylinder block or a bearing cap.

5. Install the bearing cap bolts to specification.

Important: Do not rotate the crankshaft.

6. Remove the bearing cap, leaving the gaging plastic in place. It does not matter whether the gaging plastic adheres to the journal or to the
bearing cap.
7. Measure the gaging plastic at its widest point with the scale printed on the gaging plastic package.
8. Remove the gaging plastic.
9. Select a set of bearing inserts that will produce the desired clearance.

34. Crankshaft Balancer Clean and Inspect

^ Inspect the crankshaft balancer sealing area for grooves (1).


^ Inspect the crankshaft balancer belt ribs for dents or damage.
^ Replace the crankshaft balancer if necessary.

35. Engine Flywheel Clean and Inspect


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 34
Chevrolet Venture V6-3.4L VIN E 82
Important: Do not attempt to repair the welded areas that retain the ring gear to the flywheel plate.

^ Inspect the engine flywheel for cracks.


^ Inspect the engine flywheel teeth for damage.
^ Replace the engine flywheel if necessary.

36. Piston and Connecting Rod Disassemble


^ Tools Required
- J 24086-C Piston Pin Remover/Installer

Caution: Handle the piston carefully. Worn piston rings are sharp and may cause bodily injury.

1. Remove the piston rings from the piston. Use a suitable tool in order to expand the piston rings. Do not reuse the piston rings.

Important: Do not put any load on the piston during disassembly.


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 35
Chevrolet Venture V6-3.4L VIN E 83

2. Select fork insert J 24086-310. Install the fork upside down into the press.
3. Place the piston and connecting rod assembly into the J 24086-C and press out the piston pin. Ensure that the connecting rod is above the
fork when installing the piston and connecting rod assembly into the press.
4. Mark the piston pin to the piston from which the pin was removed.

37. Piston, Connecting Rod, and Bearings Clean and Inspect


Caution: Bodily injury may occur if the carburetor cleaning fluid is exposed to the skin or if the fumes are inhaled.

Important: Clean the piston ring grooves of carbon to the bare metal. Do not scrape the piston skirt.

1. Clean the sludge and carbon from the following components:


^ The piston
^ The piston pin
Soak the pin in a carburetor cleaning solution in order to remove the varnish from the piston.
^ The connecting rod

2. Clean the piston ring grooves using a suitable ring groove cleaning tool.
3. Clean the oil lubrication holes and slots.
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 36
Chevrolet Venture V6-3.4L VIN E 84

4. Inspect the connecting rod for bending or twisting.


4.1. Install the connecting rod cap.
4.2. Place the connecting rod assembly on a checking fixture. Inspect the assembly for bending or twisting.
4.3. Do not attempt to straighten the connecting rod.
Ensure that the connecting rod meets the following conditions:
^ The connecting rods are not bent more than 0.18 mm (0.007 inch).
The connecting rods are not twisted more than 0.038 mm (0.0015 inch).
4.4. Replace any bent or twisted connecting rods.
4.5. Inspect the new connecting rods before using the new rods.

5. Inspect the connecting rod bearings for craters or pockets. Flattened sections on the connecting rod bearing halves may indicate fatigue.

6. Inspect the connecting rod bearings for excessive scoring or discoloration.


7. Inspect the connecting rod bearings for dirt or debris imbedded into the connecting rod bearing halves.
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 37
Chevrolet Venture V6-3.4L VIN E 85

8. Inspect the connecting rod bearings for improper seating indicated by bright, polished sections of the bearings.
9. Inspect the inside of the connecting rod bearing and the outside diameter of the connecting rod bearing journal for wear. This indicates high
spots.

10. Inspect the connecting rod bearing bore for taper and out-of-round.
11. Inspect the connecting rod piston pin bore for taper and out-of-round.
12. Inspect the connecting rod bores for nicks or gouges.

13. Inspect the piston for the following conditions:


^ Damage to the top of the piston (1)
^ Scoring of the skirt (2)
^ Scoring of the piston pin bore (3)
^ Broken ring groove lands
14. Inspect the piston pin for scoring or galling caused by improper installation.

Important: Take the measurements of the components with the components at normal room temperature.
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 38
Chevrolet Venture V6-3.4L VIN E 86

15. Measure the piston diameter. When measuring the piston for size or taper, ensure that the measurement is made as shown when the piston pin
is removed. If the piston is worn or damaged, replace the piston using a standard or oversize piston.

16. Inspect the piston ring-to-piston ring groove side clearance. Complete the following steps:
16.1. Insert the edge of the piston ring into the piston ring groove.
16.2. Roll the piston ring completely around the piston.
16.3. If binding is caused by a distorted piston ring groove, you may remove minor ring groove imperfections using a fine file.
16.4. If binding is caused by a distorted piston ring, replace the piston ring.

17. Measure the piston ring side clearance using a feeler gauge.
18. If the side clearance is too small, try another piston ring set.
19. If a proper piston ring-to-piston ring groove clearance cannot be achieved, replace the piston.
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 39
Chevrolet Venture V6-3.4L VIN E 87

20. Measure the piston pin diameter using an outside micrometer.

21. Measure the piston pin bore using an inside micrometer.


22. Subtract the piston pin diameter from the piston pin bore diameter in order to determine the piston pin-to-piston pin bore clearance.
23. Replace the piston and the piston pin if the piston and the piston pin are not within specifications.

24. Place the piston into the cylinder at the bottom of the ring travel.

Important: Measure the piston ring in the cylinder in which the piston may be used.

25. Place a piston ring on top of the piston.


26. Back off the piston.
27. Measure the ring gap. If the gap is below specification, increase the gap by carefully filing off excess material.

38. Piston Selection


^ Tools Required
- J 8087 Cylinder Bore Gauge
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 40
Chevrolet Venture V6-3.4L VIN E 88

Important: When fitting pistons, consider both the piston and the cylinder bore conditions together. Production and service pistons have the
same nominal weight and may be intermixed without affecting engine balance. If necessary, used pistons may be fitted selectively to any
cylinder of the engine, providing the pistons are in good condition and the same weight. Do not cut oversize pistons down or the engine
balance may be affected. Finish hone when selecting the piston.

1. Measure the piston diameter and record the reading. When measuring the piston for size or taper, ensure that the measurement is made as
shown when the piston pin is removed. If the piston worn or damaged, replace the piston with a standard or oversize piston.

2. Measure the cylinder bore, using the J 8087 If the piston is worn beyond specifications, rebore and hone to size.
3. If the cylinder bore needs reconditioning, measure the new piston diameter and hone the cylinder bore to the correct clearance.

4. Measure the J 8087. Record the reading.


5. Subtract the piston diameter from the cylinder bore diameter in order to determine the piston-to-bore clearance.
6. Compare the piston-to-bore clearance using the specifications in order to determine if the clearance is in acceptable range.
7. If a used piston is not acceptable, inspect the service piston sizes and determine if a new piston may be selected. Service pistons are available
in standard, and 0.5 mm (0.012 inch) oversize.
8. When a piston has been selected, mark the piston in order to identify the cylinder for which the piston was fitted.
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 41
Chevrolet Venture V6-3.4L VIN E 89

39. Piston and Connecting Rod Assemble


^ Tools Required
- J 24086-C Piston Pin Remover/installer

1. Select the fork insert J 24086-310. Install the fork upside down into the press.
2. Place the piston and connecting rod into the J 24086-C. Ensure that the connecting rod is above the fork when installing the piston and the
connecting rod into the press.
3. Select the pin guide J 24086-6A gold. Insert the pin guide in the piston and the connecting rod from the bottom.
4. Set the installer J 24086-9 to E-9.

Important: Ensure that the marks on the piston and connecting rod are aligned the same as when removed. If installing a new piston, ensure
that the arrow on top faces towards the front of the engine. If no identification marks were made during disassembly, ensure that the flat area
on the bottom of the piston pin skirt is aligned with the small dimple above the connecting rod crankshaft bearing bore.

5. Coat the piston pin using clean engine oil.


6. Press the piston pin into place.
7. Inspect the piston for freedom of movement.

Notice: Use a piston ring expander to install the piston rings. The rings may be damaged if expanded more than necessary.

8. Install the following components of the oil control ring assembly:


^ The expander
^ The lower oil control ring
^ The upper oil control ring
9. Install the upper and lower compression rings.
^ The chrome ring is the upper compression ring and is 1.2 mm (0.05 inch) thick.
^ The lower compression ring is chamferred and is 1.5 mm (0.06 inch) thick. The chamfer (the thickest side of the compression ring) faces
towards the bottom of the piston.

40. Camshaft Bearing Removal


^ Tools Required
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 42
Chevrolet Venture V6-3.4L VIN E 90
- J 33049 Camshaft Bearing Remover/Installer

1. Select the expander assembly and driving washer.


2. Assemble the J 33049.

3. Drive out the camshaft bearings. Use the J 33049.

41. Camshaft and Bearings Clean and Inspect


^ Tools Required
- J 7872 Magnetic Base Dial Indicator Set

1. Clean the camshaft with cleaning solvent.


2. Inspect the camshaft for the following conditions:
^ Scored camshaft bearing journals (1)
^ Damaged camshaft lobes (2)
^ Damaged camshaft sprocket locator pins (3)
^ Damaged threads (4)
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 43
Chevrolet Venture V6-3.4L VIN E 91

3. Measure the camshaft journals using a micrometer. If the camshaft journals are not within specifications, replace the camshaft.

4. Measure the camshaft runout using the J 7872.


4.1. Mount the camshaft in V-blocks between the centers.
4.2. Use the J 7872 in order to measure the intermediate camshaft journal.
5. Measure the camshaft lobe lift using the J 7872.
5.1. Lubricate the camshaft using GM P/N 1052365 or the equivalent.
5.2. Set the camshaft on V-blocks.
5.3. Use the J 7872 in order to measure the lobe lift.
6. If the runout or lobe lift is not within specifications, replace the camshaft.

42. Camshaft Bearing Installation


^ Tools Required
- J 33049 Camshaft Bearing Remover/installer

1. Assemble the J 33049 according to the manufacturer's instructions.

Notice: Severe engine damage may result if the oil holes are not correctly aligned.
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 44
Chevrolet Venture V6-3.4L VIN E 92

2. Install the camshaft bearings in the following order:


2.1. Index the camshaft bearing oil holes with the engine block oil passages.
2.2. Place the bearing on the J 33049.
2.3. Install the third camshaft bearing.
2.4. Install the second camshaft bearing.
2.5. Install the outer camshaft bearings.

3. Apply sealer GM P/N 12345493 or the equivalent to the camshaft rear bearing hole plug.
4. Install the camshaft rear bearing hole plug.

43. Timing Chain and Sprockets Clean and Inspect

^ Inspect the timing chain sprockets for teeth that are worn (1), broken (2), or chipped (3).
^ Inspect the timing chain for binding or stretching.
^ Inspect the timing chain dampener for excessive wear or cracks.
^ Replace the timing chain and sprockets as needed.

44. Valve Lifters Clean and Inspect


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 45
Chevrolet Venture V6-3.4L VIN E 93

1. Clean the valve lifters in cleaning solvent.

Caution: Wear safety glasses in order to avoid eye damage.

2. Dry the valve lifters with compressed air.


3. Inspect the valve lifters for the following:
^ Bent or broken clip (1)
^ Worn push rod socket (2)
^ Scuffed or worn sides (3)
If the valve lifter shows wear, inspect the engine block lifter bores for wear or damage.
^ Flat spots on the roller (4)
^ Loose or damaged pin (5)
^ Plugged oil hole (6)
^ Worn or damaged roller bearing
The roller should rotate freely with no binding or roughness.

4. Inspect the valve lifter guides for the following:


^ For cracks or damage
^ Excessive wear in the lifter mounting bores

45. Valve Rocker Arm and Push Rods Clean and Inspect
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 46
Chevrolet Venture V6-3.4L VIN E 94

1. Clean the valve rocker arms and push rods in cleaning solvent.

Caution: Wear safety glasses in order to avoid eye damage.

2. Dry the valve rocker arms and push rods with compressed air.
3. Inspect the valve rocker arms for the following conditions:
^ Excessive wear at the valve contact or push rod socket area (1)
^ A loose or damaged pin (2)
^ A worn or damaged roller bearing (2)
The roller should rotate freely with no binding or roughness.
^ The bolt threads for damage

Important: Keep the push rods in order. The intake and exhaust are different lengths. Exhaust is green, intake is yellow.

4. Inspect the push rods for the following conditions:


^ Straightness using a straight edge (1)
^ Excessive wear on the push rod ends (3)
^ Clogging of the oil passage (2)

46. Cylinder Head Disassemble


^ Tools Required
- J 38606 Valve Spring Compressor

Important: Ensure that the valve train components are marked, organized or sorted when disassembling the cylinder head. Install the valve
train components in the original location from which the components were removed.
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 47
Chevrolet Venture V6-3.4L VIN E 95

1. Remove the spark plugs.


2. Remove the fuel line bracket bolt and stud.
3. Remove the fuel line bracket.

Notice: Do not damage the valve guide. Remove any burrs that have formed at the key groove by chamfering the valve stem with an oil
stone or a file.

4. Compress the valve springs using the J 38606.

5. Remove the valve spring cap keys.


6. Remove the valve spring caps.
7. Remove the valve springs.
8. Remove the valves.
9. Remove the valve stem oil seals and spring seats as an assembly.

47. Cylinder Head Clean and Inspect


^ Tools Required
- J 8089 Carbon Removing Brush
- J 9666 Valve Spring Tester
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 48
Chevrolet Venture V6-3.4L VIN E 96

1. Inspect the cylinder head gasket and the mating surfaces. Inspect for leaks, corrosion, and blowby.
2. If the gasket failed, determine the cause. The following conditions may cause gasket failure:
^ Improper installation
^ A loose or warped cylinder head
^ Missing, off location, or not fully seated dowel pins
^ Low torque on the cylinder head bolts
^ Cylinder head bolts with the incorrect length
^ A warped engine block surface
^ Scratched surfaces
^ Excessive intake manifold torque
^ Cracked engine block threaded holes

Caution: Wear safety glasses in order to avoid eye damage.

Important: Do not scuff the chamber.

3. Use the J 8089 in order to remove the carbon from the combustion chambers.
4. Clean the following components:
^ The gasket surfaces
Do not use a motorized brush on any gasket sealing surface.
^ Valve stems and heads on a buffing wheel
^ The bolt hole threads
Remove all dirt, debris, or threadlocking material from the bolt holes.
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 49
Chevrolet Venture V6-3.4L VIN E 97

5. Inspect the cylinder head mating surfaces for flatness. Recondition the cylinder head mating surface, if necessary, by milling. Replace the
cylinder head if you must remove more than 0.25 mm (0.010 inch).
6. Inspect the cylinder head for cracks.
7. Inspect the cylinder head deck for corrosion. Do not attempt to weld the cylinder head. If the cylinder head is damaged, replace the cylinder
head.

8. Inspect the valve springs for squareness.

9. Use the J 9666 in order to measure the valve spring tension.


Replace the spring if the spring tension is not within specification.

48. Valve Guide Rearming and Valve and Seat Grinding


^ Tools Required
- J 8520 Camshaft Lobe Lift Indicator Set
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 50
Chevrolet Venture V6-3.4L VIN E 98

1. Inspect the valves for the following conditions:


^ Burnt or eroded areas (1)
^ A worn margin (2)
^ A bent stem (3)
^ A worn or scored stem (4)
^ A worn key groove (5)
^ A worn stem tip (6)

2. Inspect the valve face for the following conditions:


^ Worn margin (4)
^ No margin (1)
^ Pitted surfaces (2)
^ Burnt or eroded areas (3)
3. Inspect the valve seats for a loose fit in the cylinder head.

Important: Excessive valve stem-to guide clearance may cause the following conditions:
^ A noisy valve train
^ Premature valve stem oil seal wear
^ Component damage
^ Excessive engine oil consumption

Insufficient valve stem-to-guide clearance may result in noisy or sticking valves. Valves that are too tight may disturb engine smoothness or
lead to component damage.
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 51
Chevrolet Venture V6-3.4L VIN E 99

4. Inspect for excessive valve stem (1) to guide (2) clearance.

5. Use a dial indicator in order to measure the valve stem-to-guide clearance. Complete the following steps:
5.1. Install the valve into the guide.
5.2. Install the J 8520 onto the cylinder head.
5.3. Locate the dial indicator so that the movement of the valve stem from side to side (crosswise to the cylinder head) will cause a direct
movement on the indicator stem.
5.4. Ensure that the indicator stem contacts the side of the valve stem just above the valve guide.
5.5. Drop the valve head about 2 mm (1/8 inch) off the valve seat.
5.6. Use light pressure and move the valve stem side to side in order to obtain a clearance reading.
5.7. If the valve stem to guide clearance is not within specification, replace the valve and/or repair the guide in order to obtain the proper
clearances.

Important: Replace a valve stem that has excessive scoring or wear. A valve guide that is worn and has excessive stem-to-guide clearance
may need to be sleeved.

6. Ream the valve guides for oversize valves if the clearance exceeds the specifications.
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 52
Chevrolet Venture V6-3.4L VIN E 100

Important: Follow the manufacturers instructions when using valve guide reamers, sleeves, and installers.

7. Ream the valve guide in order to obtain the proper specification.

Important: Valves that are pitted must be refaced to the proper angle. Replace valve stems that show excessive wear, or replace valves that
are warped. Several different types of equipment are available for refacing valves and valve seats. Follow the manufacturers
recommendations when performing these procedures.

8. Inspect the valves for excessive scoring.

9. Inspect the valve face.


Replace the valve if the valve margin is not within specifications after grinding.
10. Reface pitted valves on a valve refacing machine in order to ensure the correct relationship between the head and the stem.

Important: Reconditioning the valve seats is very important. Ensure perfect seating of the valves in the engine in order to deliver optimum
power and performance. Clean the valve guides of all debris and dirt before grinding the valve seat.

11. Recondition the valve seats after reaming the valve guide bores or installing the new valve guides.
12. The valve seats should be concentric to within 0.05 mm (0.031 inch) total indicator reading.
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 53
Chevrolet Venture V6-3.4L VIN E 101
13. Measure valve stem installed height when the following conditions have occurred:
^ The valve stem oil seal and valve spring seat are removed.
^ All of the reconditioning has been completed.
14. If the valve stem height is not within specifications install 0.25 mm (0.010 inch), rocker arm shims as needed. If more than 2 shims are
needed replace the cylinder head or valve.

49. Cylinder Head Assemble


^ Tools Required
- J 38606 Valve Spring Compressor

Important: Use oversize valve stem seals if you install oversize valves.

1. Install the valves.


2. Lightly lap the reconditioned valves into the valve seat.
3. Install the valve stem oil seals.
4. Install the valve springs.
5. Install the valve spring caps.

6. Compress the valve springs using the J 38606.


7. Install the valve spring cap keys.
Hold the valves in place with grease, if necessary.
8. Release the valve springs.
9. Ensure that the valve locks are seated.

Notice: In order to avoid damage, install the spark plugs after the cylinder head has been installed on the engine.
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 54
Chevrolet Venture V6-3.4L VIN E 102

10. Install the fuel line bracket.

Notice: Refer to Fastener Notice in Service Precautions.

11. Install the fuel line bracket bolt and stud.


^ Tighten the fuel line bracket bolt and stud to 50 Nm (37 ft. lbs.).

50. Oil Pump Disassemble

1. Remove the oil pump driveshaft and oil pump driveshaft retainer.

Important: DO NOT remove the oil pump screen from the pipe. The pipe and oil pump screen are serviced as a complete assembly.

2. Remove the oil pump screen (if necessary).


The oil pump screen has a press fit into the oil pump cover.
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 55
Chevrolet Venture V6-3.4L VIN E 103

3. Remove the oil pump cover bolts.

4. Remove the oil pump cover.

5. Remove the oil pump drive gear and the oil pump driven gear.
6. Matchmark the gear teeth for assembly.

Caution: Wear safety glasses in order to avoid eye damage.

Caution: In some models, the pressure regulator valve spring is under pressure. Remove the retaining pin carefully in order to avoid
bodily injury.
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 56
Chevrolet Venture V6-3.4L VIN E 104

7. Remove the following items:


7.1. The oil pump pressure relief valve spring straight pin.
7.2. The oil pump pressure relief spring.

Caution: Bodily injury may occur if the cleaning solvent is inhaled or exposed to the skin.

7.3. The oil pump pressure relief valve. If the valve is stuck, soak the pump housing in carburetor cleaning solvent.

51. Oil Pump Clean and Inspect


Caution: Bodily injury may occur if the carburetor cleaning fluid is exposed to the skin or if the fumes are inhaled.

1. Clean all parts of sludge, oil, and varnish by soaking in carburetor or cleaning solvent.
2. Inspect for foreign material and determine the source of the foreign material.
3. Inspect the pump housing and cover for the following conditions:
^ Cracks or casting imperfections
^ Scoring (3)
^ Damaged threads
4. Do not attempt to repair the pump housing. Replace the pump housing.
5. Inspect the oil pump gears for the following conditions:
^ Scoring (1)
^ Excessive wear (2)
6. Inspect the idler shaft for looseness or scoring (4). If loose or damaged, replace the oil pump.
7. Inspect the drive gear shaft for looseness or scoring (5).
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 57
Chevrolet Venture V6-3.4L VIN E 105

8. Inspect the pressure regulator valve for the following conditions:


^ Scoring
^ Sticking
Burrs may be removed using a fine oil stone.
9. Inspect the pressure regulator valve spring for the following conditions:
^ Loss of tension
^ Bending
10. Inspect the suction pipe and screen assembly for the following conditions:
^ Looseness.
If the suction pipe is loose, bent or has been removed, replace the pump body cover and suction pipe.
^ Broken wire mesh or screen

11. Measure the oil pump gear lash. Install the gears, and measure in several places.

12. Measure the oil pump housing gear pocket (1, 2).
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 58
Chevrolet Venture V6-3.4L VIN E 106

13. Measure the oil pump gears (1, 2).

Important: When deciding pump serviceability based on end clearance, consider depth of the wear pattern in the pump cover.

14. Measure the oil pump gear side clearance.

52. Oil Pump Assemble


^ Tools Required
- J 21882 Oil Suction Tube Installer

1. Lubricate all the internal oil pump parts using engine oil during assembly.
2. Install the oil pump gears.
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 59
Chevrolet Venture V6-3.4L VIN E 107

3. Install the oil pump cover.

Notice: Refer to Fastener Notice in Service Precautions.

4. Install the oil pump cover bolts.


^ Tighten the oil pump cover bolts to 10 Nm (89 inch lbs.).

5. Install the pressure regulator valve.


6. Install the pressure regulator spring.
7. Install the cotter pin.

Important: Make sure the cotter pin is properly secured.

8. Apply sealer GM P/N 1050026 or the equivalent to the new suction pipe.
9. Tap the new suction pipe into place using a plastic hammer. Use the J 21882.

53. Engine Front Cover Clean and Inspect

1. Remove the crankshaft position sensor bolts from the engine front cover.
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 60
Chevrolet Venture V6-3.4L VIN E 108
2. Remove the crankshaft position sensor.

3. Clean the engine front cover with cleaning solvent.


4. Inspect the engine front cover sealing surfaces for damage.
5. Inspect the engine front cover threaded holes.
6. Repair or replace the engine front cover as necessary.

7. Install the crankshaft position sensor to the engine front cover.

Notice: Refer to Fastener Notice in Service Precautions.

8. Install the crankshaft position sensor bolts. Apply threadlock GM P/N 12345382 or the equivalent to the threads.
^ Tighten the crankshaft position sensor bolts to 10 Nm (89 inch lbs.).
54. Valve Rocker Arm Cover Clean and Inspect

1. Remove the rubber grommets.


2. Clean the valve rocker arm cover.
3. Inspect the valve rocker arm cover for damage. Replace the valve rocker arm cover if necessary.
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 61
Chevrolet Venture V6-3.4L VIN E 109

55. Oil Pan Clean and Inspect

1. Remove the oil level sensor bolt.


2. Remove the oil level sensor.
3. Clean the oil pan in solvent. Remove all sludge and debris from the bottom of the oil pan.
4. Inspect the oil pan sealing surfaces for damage. Replace the oil pan if necessary.
5. Install the oil level sensor.

Notice: Refer to Fastener Notice in Service Precautions.

6. Install the oil level sensor bolt.


^ Tighten the oil level sensor bolt to 10 Nm (89 inch lbs.).

Upper Intake Manifold

1. Remove the accelerator control cable bracket bolts (1, 2) and the nut (3).
2. Remove the accelerator control cable bracket.
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 62
Chevrolet Venture V6-3.4L VIN E 110

3. Remove the throttle body bolt and stud.


4. Remove the throttle body.
5. Remove the throttle body gasket.

6. Clean the intake manifold gasket surfaces.


7. Clean the intake manifold bolts and studs.
8. Inspect the intake manifold mating surfaces for nicks or cracks. Replace the intake manifold if damaged.

9. Install the throttle body gasket.


10. Install the throttle body.

Notice: Refer to Fastener Notice in Service Precautions.

11. Install the throttle body bolt and stud.


^ Tighten the throttle body bolt and stud to 25 Nm (18 ft. lbs.).

12. Install the accelerator control cable bracket.


13. Install the accelerator control cable bracket bolts and nut.
^ Tighten the accelerator control cable bracket bolts in sequence (1, 2, 3) to 10 Nm (89 inch lbs.).
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 63
Chevrolet Venture V6-3.4L VIN E 111

Lower Intake Manifold


^ Tools Required
- J 21882 Oil Suction Pipe Installer

1. Remove the engine coolant temperature sensor.

2. Remove the intake manifold coolant pipe bolt.


3. Remove the intake manifold coolant pipe.

4. Clean the intake manifold gasket mating surfaces.


5. Clean the fuel injector bores.
6. Inspect the threaded holes for damage.
7. Inspect the intake manifold mating surfaces for damage. Repair or replace the intake manifold as necessary.
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 64
Chevrolet Venture V6-3.4L VIN E 112

8. Apply sealant GM P/N 12345493 to the end of a new intake manifold coolant pipe.
9. Install the intake manifold coolant pipe using the J 21882.

Notice: Refer to Fastener Notice in Service Precautions.

10. Install the intake manifold coolant pipe bolt.


^ Tighten the intake manifold coolant pipe bolt to 10 Nm (89 inch lbs.).

11. Apply sealant GM P/N 12346004 or equivalent to the threads of the engine coolant temperature sensor.
12. Install the engine coolant temperature sensor.
^ Tighten the engine coolant temperature sensor to 23 Nm (17 ft. lbs.).

57. Exhaust Manifold Clean and Inspect

1. Inspect the exhaust manifold mating surface for flatness.


2. Inspect the exhaust manifold for cracks or damage. Replace the exhaust manifold if necessary.

58. Water Pump Clean and Inspect


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 65
Chevrolet Venture V6-3.4L VIN E 113

1. Remove all gasket material from the sealing surface.


2. Inspect the water pump impeller for damage.
3. Inspect the water pump shaft for looseness.
4. Replace the water pump if necessary.

59. Thread Repair


General purpose thread repair kits are available commercially.

Caution: Refer to Safety Glasses Caution in Service Precautions.

Important: Refer to the thread repair kit manufacturer's instructions regarding the size of the drill and which tap to use. Always avoid any
buildup of chips. Back out the tap every few turns and remove the chips.

1. Determine the size, the pitch, and the depth of the damaged thread.
2. Adjust the stop collars on the cutting tool as needed. Tap the stop collars to the required depth.
3. Drill out the damaged thread.
4. Remove the chips.
5. Apply clean engine oil to the top thread.
6. Use the tap in order to cut new thread.
7. Clean the thread.
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 66
Chevrolet Venture V6-3.4L VIN E 114

8. Screw the thread insert onto the mandrel of the thread insert installer. Engage the tang of the thread insert onto the end of the mandrel.

Important: The thread insert should be flush to 1 turn below the surface.

9. Lubricate the thread insert with clean engine oil (except when installing in aluminum) and install the thread insert.
10. If the tang of the thread insert does not break off when backing out the thread insert installer, break off the tang using a drift punch.

60. Service Prior to Assembly


Dirt will cause premature wear of the rebuilt engine. Clean all of the components. Use the proper tools in order to measure components when
inspecting for excessive wear. Repair or replace the components that are not within the manufacturers specification. When components are
reinstalled into an engine, return the components to their original location, position, and direction. During assembly, lubricate all of the moving
parts with clean engine oil or engine assembly lubricant (unless otherwise specified). This will provide initial lubrication when the engine is first
started.

61. Crankshaft and Bearings Installation


^ Tools Required
- J 36660-A Torque Angle Meter

Notice: Do not scrape, shim, or file bearing inserts. If the bearing surface of the insert is touched with bare fingers, the skin oil and acids will
etch the bearing surface.

Important: Ensure that the crankshaft bearing cap bolt holes and the crankshaft bearing cap mating surfaces are clean and dry.

1. Dip the crankshaft bearing cap bolts in clean engine oil.

Notice: Upper and lower inserts may be different. Do not obstruct any oil passages.

2. Place the crankshaft bearing inserts into the crankshaft bearing cap and into the engine block.

Important: The crankshaft bearing inserts will project slightly when put into place. Ensure that the bearing inserts project an equal distance
on both sides. Ensure that the insert tangs are engaged.

3. Coat the crankshaft main thrust bearing surface with GM EOS P/N 1052368 or the equivalent.
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 67
Chevrolet Venture V6-3.4L VIN E 115
4. Lubricate the crankshaft main bearing surface with clean engine oil.
5. Install the crankshaft.

Notice: In order to prevent the possibility of cylinder block or crankshaft bearing cap damage, the crankshaft bearing caps are tapped into
the cylinder block cavity using a brass, lead, or a leather mallet before the attaching bolts are installed. Do not use attaching bolts to pull the
crankshaft bearing caps into the seats. Failure to use this process may damage a cylinder block or a bearing cap.

6. Install the crankshaft main bearing caps. Apply a small amount of sealer GM P/N 1052942 to the rear of the #4 crankshaft main bearing cap
sealing surface.

Notice: Refer to Fastener Notice in Service Precautions.

7. Install the crankshaft main bearing cap bolts.


Use the J 36660-A in order to tighten the crankshaft main bearing cap bolts to 50 Nm (37 ft. lbs.) plus 77 degrees.
8. Measure the crankshaft end play.

62. Crankshaft Rear Oil Seal Installation


^ Tools Required
- J 34686 Crankshaft Rear Oil Seal Installer

1. Apply engine oil to the inside diameter and the outside diameter of the new crankshaft rear oil seal.
2. Slide the crankshaft rear oil seal over the mandrel until the back of the crankshaft rear oil seal bottoms squarely against the collar of the tool.
3. Perform the following steps in order to install the crankshaft rear oil seal:
3.1. Align the dowel pin of the J 34686 with the dowel pin in the crankshaft.

Notice: Refer to Fastener Notice in Service Precautions.

3.2. Attach the J 34686 to the crankshaft by hand, or tighten attaching screws to 5 Nm (45 inch lbs.).
3.3. Turn the T-handle of the J 34686 in order to engage allow the collar to push the seal into the bore.
Turn the handle until the collar is tight against the case. Ensure that the seal is seated properly.
3.4. Loosen the T-handle until the T-handle comes to a stop.
3.5. Remove the attaching screws.

63. Piston, Connecting Rod, and Bearing Installation


^ Tools Required
- J 5239 Connecting Rod Guide
- J 8037 Piston Ring Compressor
- J 36660-A Torque Angle Meter

Important: The piston and cylinder bore have been measured and the bore has been sized for the proper clearance. Install the piston and
connecting rod assembly into the proper cylinder bore. The piston alignment mark MUST face the front of the engine block.
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 68
Chevrolet Venture V6-3.4L VIN E 116

1. Lightly lubricate the following components with clean engine oil:


^ The piston
^ The piston rings
^ The cylinder bore
^ The bearing surfaces
2. Stagger the oil control ring end gaps a minimum of 90 degrees.
3. Stagger the compression ring end gaps a minimum of 25 mm (1.0 inch).
4. Install the J 8037 onto the piston and compress the piston rings.

Important: The piston alignment mark MUST be facing the front of the engine block.

5. Install the J 5239 on the connecting rod bolts.

6. Install the piston and connecting rod assembly into the proper cylinder bore.
7. Hold the piston ring compressor firmly against the engine block. Using a wooden hammer handle, lightly tap the top of the piston until all of
the piston rings enter the cylinder bore.
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 69
Chevrolet Venture V6-3.4L VIN E 117

8. Guide the connecting rod end onto the crankshaft journal.

Notice: Refer to Fastener Notice in Service Precautions.

9. Install the bearing, cap, and nuts.


9.1. Tighten the connecting rod bearing cap nuts a first pass to 20 Nm (15 ft. lbs.).
9.2. Tighten the connecting rod bearing cap nuts a second pass to 75 degrees using the J 36660-A.

10. With the pistons and connecting rods installed, use a soft faced mallet and lightly tap each connecting rod assembly parallel to the crankpin to
make sure that the rods have side clearance.
11. Measure the connecting rod side clearance using a feeler gauge or dial indicator. Connecting rod side clearance should be within 0.18 - 0.44
mm (0.007 - 0.017 inch).

64. Camshaft Installation

1. Coat the camshaft journals with clean engine oil.


2. Coat the camshaft lobes with prelube GM P/N 1052365 or the equivalent.
3. Install the camshaft using the following procedure:
3.1. Install a large screwdriver into the camshaft bolt hole for support. Do not damage the threads.
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 70
Chevrolet Venture V6-3.4L VIN E 118
3.2. Rotate the camshaft while installing the camshaft into the camshaft bearings.

4. Install the camshaft thrust plate.

Notice: Refer to Fastener Notice in Service Precautions.

5. Install the camshaft thrust plate screws.


^ Tighten the camshaft thrust plate screws to 10 Nm (89 inch lbs.).

65. Timing Chain and Sprockets Installation


^ Tools Required
- J 38612 Crankshaft Sprocket Installer

1. Install the crankshaft sprocket using the J 38612.


2. Apply prelube GM P/N 1052365 or the equivalent to the crankshaft sprocket thrust surface.

3. Install the timing chain dampener.


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 71
Chevrolet Venture V6-3.4L VIN E 119

Notice: Refer to Fastener Notice in Service Precautions.

4. Install the timing chain dampener bolts.


^ Tighten the timing chain dampener bolt to 21 Nm (15 ft. lbs.).

5. Align the crankshaft timing mark (2) to the timing mark on the bottom of the timing chain dampener (1).
6. Hold the camshaft sprocket with the timing chain hanging down and install the timing chain to the crankshaft gear.
7. Align the timing mark on the camshaft gear (4) with the timing mark on top of the timing chain dampener (3).

8. Align the dowel in the camshaft with the dowel hole in the camshaft sprocket.
9. Draw the camshaft sprocket onto the camshaft using the mounting bolt.
10. Coat the crankshaft and camshaft sprocket with engine oil.
^ Tighten the bolt to 140 Nm (103 ft. lbs.).
66. Engine Front Cover Installation

1. Install the engine front cover gasket.


2. Apply sealer GM P/N 12346004 or the equivalent to both sides of the lower tabs of the engine front cover gasket.
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 72
Chevrolet Venture V6-3.4L VIN E 120

3. Install the engine front cover.

Notice: Refer to Fastener Notice in Service Precautions.

4. Install the engine front cover bolts (3).


^ Tighten the bolts (3) to 55 Nm (41 ft. lbs.).
5. Install the engine front cover bolt (1).
^ Tighten the bolt (1) to 47 Nm (35 ft. lbs.).
6. Install the engine front cover bolts (2).
^ Tighten the bolts (2) to 21 Nm (115 ft. lbs.).
67. Crankshaft Front Oil Seal Installation
^ Tools Required
- J 35468 Crankshaft Front Oil Seal Installer

1. Align the J 35468 and the crankshaft front oil seal with the engine front cover and crankshaft.
2. Install the crankshaft front oil seal using the J 35468 and a suitable tool.

68. Oil Pump Drive Installation


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 73
Chevrolet Venture V6-3.4L VIN E 121

1. Apply prelube GM P/N 1052365 or the equivalent to the oil pump drive gear.
2. Apply engine oil to the oil pump drive gear assembly for ease of assembly.
3. Install the oil pump drive gear assembly.
4. Install the oil pump drive gear clamp.

Notice: Refer to Fastener Notice in Service Precautions.

5. Install the oil pump drive gear clamp bolt.


^ Tighten the oil pump drive gear clamp bolt to 36 Nm (27 ft. lbs.).

69. Oil Pump Installation

1. Install the crankshaft oil deflector.

Notice: Refer to Fastener Notice in Service Precautions.

2. Install the crankshaft oil deflector nuts.


^ Tighten the crankshaft oil deflector nuts to 25 Nm (18 ft. lbs.).

Important: Do not reuse the oil pump driveshaft retainer. During assembly, install a NEW oil pump driveshaft retainer.
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 74
Chevrolet Venture V6-3.4L VIN E 122

3. Install the oil pump.


4. Position the oil pump onto the pins.

Notice: Refer to Fastener Notice in Service Precautions.

5. Install the oil pump bolt attaching the oil pump to the rear crankshaft bearing cap.
^ Tighten the oil pump bolt to 41 Nm (30 ft. lbs.).

70. Oil Pan Installation

1. Apply sealer GM P/N 1234579 or the equivalent to both sides of the crankshaft rear main bearing cap (1). Press sealer into gap using a putty
knife.

2. Install the oil pan gasket.


3. Install the oil pan.

Notice: Refer to Fastener Notice in Service Precautions.

4. Install the oil pan bolts.


^ Tighten the oil pan bolts to 25 Nm (18 ft. lbs.).
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 75
Chevrolet Venture V6-3.4L VIN E 123
5. Install the oil pan side bolts.
^ Tighten the oil pan side bolts to 50 Nm (37 ft. lbs.).

71. Cylinder Head Installation - Left and Right


This article has been updated with TSB 02-06-01-003B, 4/15/08
This bulletin is being revised to include a Notice advising that the cylinder head bolts are NOT TO BE RE-USED. Please discard Corporate
Bulletin Number 02-06-01-003A.

^ Tools Required
- J 36660-A Torque Angle Meter

1. Install the dowel pins (cylinder head locator) (if necessary).


2. Inspect the dowel pins (cylinder head locator) for proper installation.
3. Install the cylinder head gasket.

4. Install the cylinder head.

Notice: Refer to Fastener Notice in Service Precautions.

Notice: This component uses torque-to-yield bolts. When servicing this component, do not re-use the bolts. New torque-to-yield bolts must
be installed. Re-using used torque-to-yield bolts will not provide proper bolt torque and clamp load. Failure to install NEW torque-to-yield
bolts may lead to engine damage.

5. Install the NEW cylinder head bolts.


- Tighten the NEW cylinder head bolts to 60 Nm (44 lb ft) in the order shown. Use the J 36660-A torque angle meter in order to rotate the
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 76
Chevrolet Venture V6-3.4L VIN E 124
cylinder head bolts an additional 95 degrees.
72. Water Pump Installation

1. Install the water pump gasket.


2. Install the water pump.

Notice: Refer to Fastener Notice in Service Precautions.

3. Install the water pump bolts.


^ Tighten the water pump bolts to 10 Nm (89 inch lbs.).

4. Install the water pump pulley.


5. Install the water pump pulley bolts.
^ Tighten the water pump pulley bolts to 25 Nm (18 ft. lbs.).

73. Valve Lifter Installation

1. Coat the valve lifters using prelube GM P/N 1052365 or the equivalent.
2. Install the valve lifters in their original locations.
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 77
Chevrolet Venture V6-3.4L VIN E 125
3. Apply threadlock GM P/N 12345382 or the equivalent to the threads.

Notice: Refer to Fastener Notice in Service Precautions.

4. Install the valve lifter guides and guide bolts.


^ Tighten the valve lifter guide bolts to 10 Nm (89 inch lbs.).

74. Valve Rocker Arm and Push Rod Installation


^ Tools Required
- J 36660-A Torque Angle Meter

1. Install the lower intake manifold gaskets.

2. Coat the ends of the push rods using prelube GM P/N 1052365 or the equivalent.

Important: The intake valve push rods measure 144 mm (5.75 inch) in length, (yellow).

3. Install the push rods in their original location. The exhaust valve push rods measure 152.5 mm (6.0 inch) in length, (green).
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 78
Chevrolet Venture V6-3.4L VIN E 126

4. Coat the rocker arm friction surfaces using prelube GM P/N 1052365 or the equivalent.

Important: Shims may be required under the valve rocker arm pedestals if reconditioning has been performed on the cylinder head or its
components. Refer to Cylinder Head Clean and Inspect.

5. Install the valve rocker arms in their original positions.

Notice: Refer to Fastener Notice in Service Precautions.

6. Install the valve rocker arm bolts.


Use the J 36660-A to tighten the valve rocker arm bolts to 19 Nm (14 ft. lbs.) plus 30 degrees.

Left Exhaust Manifold

1. Install the exhaust manifold gasket.


2. Install the exhaust manifold.

Notice: Refer to Fastener Notice in Service Precautions.

3. Install the exhaust manifold nuts.


^ Tighten the exhaust manifold nuts to 16 Nm (12 ft. lbs.).
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 79
Chevrolet Venture V6-3.4L VIN E 127

4. Install the exhaust manifold heat shield.


5. Install the exhaust manifold heat shield bolts.
^ Tighten the exhaust manifold heat shield bolts to 10 Nm (89 inch lbs.).

Right Exhaust Manifold

1. Install the exhaust manifold gasket.


2. Install the exhaust manifold.

Notice: Refer to Fastener Notice in Service Precautions.

3. Install the exhaust manifold nuts.


^ Tighten the exhaust manifold nuts to 16 Nm (12 ft. lbs.).
4. Install the right side spark plugs.
^ Tighten the spark plugs to 27 Nm (20 ft. lbs.).

5. Install the exhaust manifold lower heat shield.


6. Install the exhaust manifold upper heat shield.
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 80
Chevrolet Venture V6-3.4L VIN E 128
7. Install the exhaust manifold heat shield bolts.
^ Tighten the exhaust manifold heat shield bolts to 10 Nm (89 inch lbs.).

8. Coat the threads of the heated oxygen sensor with anti-seize compound GM P/N 5613695, or the equivalent.
9. Install the heated oxygen sensor.
^ Tighten the heated oxygen sensor to 42 Nm (31 ft. lbs.).

76. Exhaust Crossover Installation

1. Install the exhaust crossover pipe.

Notice: Refer to Fastener Notice in Service Precautions.

2. Install the exhaust crossover pipe nuts.


^ Tighten the exhaust crossover pipe nuts to 25 Nm (18 ft. lbs.).

3. Install the exhaust crossover pipe heat shield.


4. Install the exhaust crossover pipe heat shield bolts.
^ Tighten the exhaust crossover pipe heat shield bolts to 10 Nm (89 inch lbs.).
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 81
Chevrolet Venture V6-3.4L VIN E 129
Lower Intake Manifold

1. Apply sealer GM P/N 12345739 or the equivalent at the engine block-to-lower intake manifold mating surface. Ensure that the bead meets
the following conditions:
^ 2.0-3.0 mm (0.08-0.12 inch) wide
^ 3.0-5.0 mm (0.12-0.20 inch) thick
2. Install the lower intake manifold.

Notice: Failure to tighten vertical bolts before the diagonal bolts may cause an oil leak.

3. Apply sealer GM P/N 12345382 or the equivalent to the lower intake manifold bolt threads.

Notice: Refer to Fastener Notice in Service Precautions.

4. Install the lower intake manifold bolts.


^ Tighten the lower intake manifold bolts in sequence to 13 Nm (115 inch lbs.).

5. Install the heater inlet pipe.


6. Install the heater inlet pipe nut.
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 82
Chevrolet Venture V6-3.4L VIN E 130
^ Tighten the heater inlet pipe nut to 25 Nm (18 ft. lbs.).

Important: Do not press on the fuel pressure regulator valve when installing the fuel injector rail assembly.

7. Install the fuel injector rail assembly.


7.1. Lubricate the fuel injector O-rings using GM P/N 1051885 or the equivalent.
7.2. Install the injector nozzles into the lower intake manifold injector bores.
7.3. Press on the injector rail using the palms of both hands until the injectors are fully seated.
8. Install the fuel injector rail bolts.
^ Tighten the fuel injector rail bolts to 10 Nm (89 inch lbs.).

9. Install the fuel feed and return pipe retaining clip.


10. Install the fuel feed and return pipe retaining clip bolt.
^ Tighten the fuel feed and return pipe retaining clip bolt to 8 Nm (71 inch lbs.).

Upper Intake Manifold


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 83
Chevrolet Venture V6-3.4L VIN E 131

1. Install the upper intake manifold gaskets.


2. Apply threadlock GM P/N 12345382 or equivalent to the threads of the intake manifold bolts.
3. Install the upper intake manifold.

Notice: Refer to Fastener Notice in Service Precautions.

4. Install the upper intake manifold bolts and studs.


^ Tighten the upper intake manifold bolts and studs to 25 Nm (118 ft. lbs.).

5. Install the spark plug wires.


6. Install the EGR valve pipe and gasket.
^ Tighten the EGR valve pipe to 25 Nm (18 ft. lbs.).
7. Install the EGR valve and gasket.
8. Install the EGR valve bolts.
^ Tighten the EGR valve bolts to 25 Nm (18 ft. lbs.).

9. Install the MAP sensor.


10. Install the MAP sensor bolts.
^ Tighten the MAP sensor bolts to 5 Nm (44 inch lbs.).
11. Connect the MAP sensor electrical connector.

Left Valve Rocker Arm Cover


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 84
Chevrolet Venture V6-3.4L VIN E 132

1. Install the valve rocker arm cover gasket into the valve rocker arm cover.
2. Apply sealer GM P/N 12345739 or the equivalent to the notches where the cylinder head and intake manifold meet.
3. Install the valve rocker arm cover.

Notice: Refer to Fastener Notice in Service Precautions.

4. Install the valve rocker arm cover bolts.


^ Tighten the valve rocker arm cover bolts to 10 Nm (89 inch lbs.).

5. Install the electronic ignition control module.


6. Install the electronic ignition control module nuts and bolts.
^ Tighten the electronic ignition control module nuts and bolts to 25 Nm (18 ft. lbs.).
7. Install the spark plug wires.

Right Valve Rocker Arm Cover

1. Install the valve rocker arm cover gasket into the valve rocker arm cover.
2. Apply sealer GM P/N 12345739 or the equivalent to the notches where the cylinder head and intake manifold meet.
3. Install the valve rocker arm cover.

Notice: Refer to Fastener Notice in Service Precautions.


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 85
Chevrolet Venture V6-3.4L VIN E 133

4. Install the valve rocker arm cover bolts.


^ Tighten the valve rocker arm cover bolts to 10 Nm (89 inch lbs.).

5. Install the vacuum lines to the upper intake manifold.

79. Water Outlet Installation

1. Install the Thermostat.

2. Install the water outlet gasket.


3. Install the water outlet.

Notice: Refer to Fastener Notice in Service Precautions.

4. Install the water outlet bolts.


^ Tighten the water outlet bolts to 25 Nm (18 ft. lbs.).

80. Oil Filter Adapter Installation


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 86
Chevrolet Venture V6-3.4L VIN E 134

1. Install the oil filter bypass valve.

Notice: Refer to Fastener Notice in Service Precautions.

2. Install the oil filter fitting, if necessary.


^ Tighten the oil filter fitting to 39 Nm (29 ft. lbs.).
3. Install the oil filter bypass valve plug. Apply sealer GM P/N 12345739 or the equivalent to the threads.
^ Tighten the oil filter bypass valve plug to 19 Nm (14 ft. lbs.).

4. Install the oil filter.


^ Tighten the oil filter to 13 Nm (115 inch lbs.).
81. Oil Level Indicator and Tube Installation

1. Apply sealer GM P/N 12345739 or the equivalent to the area of the oil level indicator tube that goes into the engine block.
2. Install the oil level indicator and oil level indicator tube.
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 87
Chevrolet Venture V6-3.4L VIN E 135

3. Install the thermostat bypass pipe.


4. Install the thermostat bypass pipe hose.
5. Install the thermostat bypass pipe hose clamps.

Notice: Refer to Fastener Notice in Service Precautions.

6. Install the thermostat bypass pipe to engine front cover bolt (4).
^ Tighten the thermostat bypass pipe to engine front cover bolt to 11 Nm (98 inch lbs.).
7. Install the thermostat bypass pipe to cylinder head nut (3).
^ Tighten the thermostat bypass pipe to cylinder head nut to 25 Nm (18 ft. lbs.).

8. Install the thermostat bypass pipe to throttle body hose clamps.


9. Install the thermostat bypass pipe to throttle body nut.
^ Tighten the thermostat bypass pipe to throttle body nut to 25 Nm (18 ft. lbs.).
82. Generator and Engine Lift Front Bracket Installation
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 88
Chevrolet Venture V6-3.4L VIN E 136

1. Install the front engine lift hook.


2. Install the generator bracket.

Notice: Refer to Fastener Notice in Service Precautions.

3. Install the generator bracket bolts.


^ Tighten the generator bracket bolts in sequence (1, 2, 3) to 50 Nm (37 ft. lbs.).

83. Engine Mount Strut and Engine Lift Bracket Installation

1. Install the engine mount strut and lift bracket.

Notice: Refer to Fastener Notice in Service Precautions.

2. Install the engine mount strut and lift bracket bolts.


^ Tighten the engine mount strut and lift bracket bolts to 70 Nm (52 ft. lbs.).

84. Engine Mount Strut and A/C Compressor Bracket Installation


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 89
Chevrolet Venture V6-3.4L VIN E 137

1. Install the engine mount strut and A/C Compressor bracket.

Notice: Refer to Fastener Notice in Service Precautions.

2. Install the engine mount strut and A/C Compressor bracket bolts.
^ Tighten the engine mount strut and lift bracket bolts to 50 Nm (37 ft. lbs.).

85. Drive Belt Tensioner Installation

1. Install the drive belt tensioner.

Notice: Refer to Fastener Notice in Service Precautions.

2. Install the drive belt tensioner bolt.


^ Tighten the drive belt tensioner bolt to 50 Nm (37 ft. lbs.).

86. Engine Flywheel Installation


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 90
Chevrolet Venture V6-3.4L VIN E 138

1. Install the flywheel.


2. Install the flywheel retainer.

Notice: Refer to Fastener Notice in Service Precautions.

3. Install the flywheel bolts.


^ Tighten the flywheel bolts to 71 Nm (52 ft. lbs.).

87. Crankshaft Balancer Installation

^ Tools Required
- J 29113 Crankshaft Balancer Installer

1. Apply sealer GM P/N 12345739 or the equivalent to the keyway of the crankshaft balancer.
2. Place the crankshaft balancer into position over the key in the crankshaft.
3. Install the J 29113 onto the crankshaft.
4. Pull the crankshaft balancer into position.
5. Remove the J 29113 from the crankshaft balancer.

Notice: Refer to Fastener Notice in Service Precautions.


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 91
Chevrolet Venture V6-3.4L VIN E 139

6. Install the crankshaft balancer washer and bolt.


^ Tighten the crankshaft balancer bolt to 103 Nm (76 ft. lbs.).
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 1
Chevrolet Venture V6-3.4L VIN E 140
Compression Check: Testing and Inspection
A compression pressure test of the engine cylinders determines the condition of the rings, the valves, and the head gasket.

Important: Remove the Powertrain Control Module (PCM) and the ignition fuses from the I/P fuse block.

1. Disable the ignition.


2. Disable the fuel systems.
3. Remove the spark plugs from all the cylinders.
4. Remove the air duct from the throttle body.
5. Block the throttle plate in the open position.
6. Measure the engine compression, using the following procedure:
6.1. Firmly install the compression gauge to the spark plug hole.
6.2. Have an assistant crank the engine through at least 4 compression strokes in the testing cylinder.
6.3. Record the readings on the gauge at each stroke.
6.4. Disconnect the gauge.
6.5. Repeat the compression test for each cylinder.
7. Record the compression readings from all of the cylinders.
^ The lowest reading should not be less than 70 percent of the highest reading.
^ No cylinder reading should be less than 689 kPa (100 psi).
8. The following list is examples of the possible measurements:
^ When the compression measurement is normal, the compression builds up quickly and evenly to the specified compression on each
cylinder.
^ When the compression is low on the first stroke and tends to build up on the following strokes, but does not reach the normal
compression, the piston rings may be the cause.
^ If the compression improves considerably with the addition of three squirts of oil, the piston rings may be the cause.
^ When the compression is low on the first stroke and does not build up in the following strokes, the valves may be the cause.
^ The addition of oil does not affect the compression, the valves may be the cause.
^ When the compression is low on two adjacent cylinders, or coolant is present in the crankcase, the head gasket may be the cause.
9. Remove the block from the throttle plate.
10. Install the air duct to the throttle body.
11. Install the spark plugs.
12. Install the Powertrain Control Module (PCM) fuse.
13. Install the ignition fuse to the I/P fuse block.
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 1
Chevrolet Venture V6-3.4L VIN E 141
Crankshaft Balancer: Description and Operation

The 24X crankshaft position (CKP) sensor (1), secured in a mounting bracket (3) and bolted to the front side of the engine timing chain cover (2),
is partially behind the crankshaft balancer.

The 7X CKP sensor uses a two wire connector at the sensor and a three-way connector at the ignition control module.

The 24X CKP sensor contains a Hall-effect switch. The magnet and Hall-effect switch are separated by an air gap. A Hall-effect switch reacts like a
solid stale switch, grounding a low current signal voltage when a magnetic field is present. When the magnetic field is shielded from the switch by
a piece of steel placed in the air gap between the magnet and the switch, the signal voltage is not grounded. If the piece of steel (called an
interrupter) is repeatedly moved in and out of the air gap, the signal voltage will appear to go on-off, on-off, on-off. Compared to a conventional
mechanical distributor, this on-off signal is similar to the signal that a set of breaker points in the distributor would generate as the distributor shaft
turned and the points opened and closed.

In the case of the electronic ignition system, the piece of steel is a concentric interrupter ring mounted to the rear of the crankshaft balancer. The
interrupter ring has blades and windows that, with crankshaft rotation, either block the magnetic field or allow the field to reach the Hall-effect
switch. The Hall-effect switch is called a 24X CKP sensor, because the interrupter ring has 24 evenly spaced blades and windows. The 24X CKP
sensor produces 24 on-off pulses per crankshaft revolution.

The interrupter ring is a special wheel cast on the crankshaft that has seven machined slots, six of which are equally spaced 60 degrees apart. The
seventh slot is spaced 10 degrees from one of the other slots. As the interrupter ring rotates with the crankshaft, the slots change the magnetic field.
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 2
Chevrolet Venture V6-3.4L VIN E 142
This will cause the 7X to ground the 3X signal voltage that is supplied by the ignition control module. The ignition control module interprets the
7X on-off signals as an indication of crankshaft position. The ignition control module must have the 7X signal to fire the correct ignition coil.

The 7X interrupter ring and Hall-effect switch react similarly. The 24X signal is used for better resolution at a calibrated RPM.
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 1
Chevrolet Venture V6-3.4L VIN E 143
Drive Belt: Testing and Inspection

- Symptoms - Drive Belt


Important: Review the system operation in order to familiarize yourself with the system functions. Refer to Drive Belt System Description.

Visual/Physical Inspection
^ Inspect for aftermarket devices which could affect the operation of the drive belts.
^ Inspect the easily accessible or visible system components for obvious damage or conditions which could cause the symptom.
^ Inspect the drive belt for excessive wear, shredding, or missing sections.
^ Inspect the drive belt for contamination of excessive dirt, oil, coolant or other substances that may affect the drive belt operation.

Intermittent
^ Drive belt symptoms may be from intermittent failure of an accessory drive component.
^ Drive belt symptoms may occur from changes in load of the accessory drive components.
^ Ambient temperatures, moisture, or engine operating temperature can affect the drive belt operation.

Symptom List
Refer to a symptom diagnostic procedure from the following list in order to diagnose the symptom:

^ Drive Belt Chirping Diagnosis


See: Drive Belt Chirping

^ Drive Belt Squeal Diagnosis


See: Drive Belt Squeal

^ Drive Belt Whine Diagnosis


See: Drive Belt Whine

^ Drive Belt Rumbling Diagnosis


See: Drive Belt Rumbling

^ Drive Belt Vibration Diagnosis


See: Drive Belt Vibration

^ Drive Belt Falls Off Diagnosis


See: Drive Belt Falls Off

^ Drive Belt Excessive Wear Diagnosis


See: Drive Belt Excessive Wear

Drive Belt Chirping


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 2
Chevrolet Venture V6-3.4L VIN E 144

Diagnostic Aids
The symptom may be intermittent due to moisture on the drive belt(s) or the pulleys. It may be necessary to spray a small amount of water on the
drive belt(s) in order to duplicate the customers concern. If spraying water on the drive belt(s) duplicates the symptom, cleaning the belt pulleys
may be the probable solution.
A loose or improper installation of a body component, a suspension component, or other items of the vehicle may cause the chirping noise.

Test Description
The number(s) below refer to the step number(s) on the diagnostic table.
2. The noise may not be engine related. This step is to verify that the engine is making the noise. If the engine is not making the noise do not
proceed further with this table.
3. The noise may be an internal engine noise. Removing the drive belt and operating the engine for a brief period will verify the noise is related
to the drive belt. When removing the drive belt(s) the water pump may not be operating and the engine may overheat. Also DTCs may set
when the engine is operating with the drive belt removed.
4. Inspect all drive belt pulleys for pilling. Pilling is the small balls or pills or it may be strings in the drive belt grooves from the accumulation
of rubber dust.
6. Misalignment of the pulleys may be caused from improper mounting of the accessory drive component, incorrect installation of the accessory
drive component pulley, or the pulley bent inward or outward from a previous repair. Test for a misalign pulley using a straight edge in the
pulley grooves across two or three pulleys. If a misalign pulley is found refer to that accessory drive component for the proper installation
procedure for that pulley.
10. Inspecting of the fasteners can eliminate the possibility that a wrong bolt, nut, spacer, or washer was installed.
12. Inspecting the pulleys for being bent should include inspecting for a dent or other damage to the pulleys that would prevent the drive belt
from not seating properly in all of the pulley grooves or on the smooth surface of a pulley when the back side of the belt is used to drive the
pulley.
14. Replacing the drive belt when it is not damaged or there is not excessive pilling will only be a temporary repair.

Drive Belt Excessive Wear


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 3
Chevrolet Venture V6-3.4L VIN E 145

Diagnostic Aids
Excessive wear on a drive belt(s) is usually caused by an incorrect installation or the wrong drive belt for the application.
Minor misalignment of the drive belt pulleys will not cause excessive wear, but will probably cause the drive belt(s) to make a noise or to fall off.
Excessive misalignment of the drive belt pulleys will cause excessive wear but may also make the drive belt(s) fall off.

Test Description
The number(s) below refer to the step number(s) on the diagnostic table.
2. The inspection is to verify the drive belt(s) is correctly installed on all of the drive belt pulleys. Wear on the drive belt(s) may be caused by
mis-positioning the drive belt(s) by one groove on a pulley.
3. The installation of a drive belt that is two wide or two narrow will cause wear on the drive belt. The drive belt ribs should match all of the
grooves on all of the pulleys.
4. This inspection is to verify the drive belt(s) is not contacting any parts of the engine or body while the engine is operating. There should be
sufficient clearance when the drive belt accessory drive components load varies. The drive belt(s) should not come in contact with an engine
or a body component when snapping the throttle.

Drive Belt Falls Off


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 4
Chevrolet Venture V6-3.4L VIN E 146

Diagnostic Aids
If the drive belt(s) repeatedly falls off the drive belt pulleys, this is because of pulley misalignment. An extra load that is quickly applied on
released by an accessory drive component may cause the drive belt to fall off the pulleys. Verify the accessory drive components operate
properly.
If the drive belt(s) is the incorrect length, the drive belt tensioner may not keep the proper tension on the drive belt.

Test Description
The number(s) below refer to the step number(s) on the diagnostic table.
2. This inspection is to verify the condition of the drive belt. Damage may of occurred to the drive belt when the drive belt fell off. The drive
belt may of been damaged, which caused the drive belt to fall off. Inspect the belt for cuts, tears, sections of ribs missing, or damaged belt
plys.
4. Misalignment of the pulleys may be caused from improper mounting of the accessory drive component, incorrect installation of the accessory
drive component pulley, or the pulley bent inward or outward from a previous repair. Test for a misalign pulley using a straight edge in the
pulley grooves across two or three pulleys. If a misalign pulley is found refer to that accessory drive component for the proper installation
procedure of that pulley.
5. Inspecting the pulleys for being bent should include inspecting for a dent or other damage to the pulleys that would prevent the drive belt
from not seating properly in all of the pulley grooves or on the smooth surface of a pulley when the back side of the belt is used to drive the
pulley.
6. Accessory drive component brackets that are bent or cracked may will let the drive belt fall off.
7. Inspecting of the fasteners can eliminate the possibility that a wrong bolt, nut, spacer, or washer was installed. Missing, loose, or the wrong
fasteners may cause pulley misalignment from the bracket moving under load. Over tightening of the fasteners may cause misalignment of
the accessory component bracket.

Drive Belt Rumbling


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 5
Chevrolet Venture V6-3.4L VIN E 147

Diagnostic Aids
Vibration from the engine operating may cause a body component or another part of the vehicle to make rumbling noise.
The drive belt(s) may have a condition that can not be seen or felt. Sometimes replacing the drive belt may be the only repair for the symptom.
If replacing the drive belt(s), completing the diagnostic table, and the noise is only heard when the drive belt(s) is installed, there might be an
accessory drive component with a failure. Varying the load on the different accessory drive components may aid in identifying which component
is causing the rumbling noise.

Test Description
The number(s) below refer to the step number(s) on the diagnostic table.
2. This test is to verify that the symptom is present during diagnosing. Other vehicle components may cause a similar symptom.
3. This test is to verify that the drive belt(s) is causing the rumbling noise. Rumbling noise may be confused with an internal engine noise due to
the similarity in the description. Remove only one drive belt at a time if the vehicle has multiple drive belts. When removing the drive belt the
water pump may not be operating and the engine may overheat. Also DTCs may set when the engine is operating with the drive belt
removed.
4. Inspecting the drive belt(s) is to ensure that it is not causing a the noise. Small cracks across the ribs of the drive belt will not cause the noise.
Belt separation is identified by the plys of the belt separating and may be seen at the edge of the belt our felt as a lump in the belt.
5. Small amounts of pilling is normal condition and acceptable. When the pilling is severe the drive belt does not have a smooth surface for
proper operation.

Drive Belt Squeal


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 6
Chevrolet Venture V6-3.4L VIN E 148

Diagnostic Aids
A loose or improper installation of a body component, a suspension component, or other items of the vehicle may cause the squeal noise. If the
noise is intermittent, verify the accessory drive components by varying their loads making sure they are operated to their maximum capacity. An
overcharged A/C system, power steering system with a pinched hose or wrong fluid, or a generator failing are suggested items to inspect.

Test Description
The number(s) below refer to the step number(s) on the diagnostic table.
2. The noise may not be engine related. This step is to verify that the engine is making the noise. If the engine is not making the noise do not
proceed further with this table
3. The noise may be an internal engine noise. Removing the drive belt and operating the engine for a brief period will verify the squeal noise is
the drive belt(s) or an accessory drive component. When removing the drive belt the water pump may not be operating and the engine may
overheat. Also DTCs may set when the engine is operating with the drive belt removed.
4. This test is to verify that an accessory drive component does not have a seized bearing. With the belt remove test the bearings in the
accessory drive components for turning smoothly. Also test the accessory drive components with the engine operating by varying the load on
the components to verify that the components operate properly.
5. This test is to verify that the drive belt tensioner operates properly. If the drive belt tensioner is not operating properly, proper belt tension
May not be achieved to keep the drive belt from slipping which could cause a squeal noise.
6. This test is to verify that the drive belt(s) is not too long, which would prevent the drive belt tensioner from working properly. Also if an
incorrect length drive belt was installed, it may not be routed properly and may be turning an accessory drive component in the wrong
direction.
7. Misalignment of the pulleys may be caused from improper mounting of the accessory drive component, incorrect installation of the accessory
drive component pulley, or the pulley bent inward or outward from a previous repair. Test for a misalign pulley using a straight edge in the
pulley grooves across two or three pulleys. If a misalign pulley is found refer to that accessory drive component for the proper installation
procedure for that pulley.
8. This test is to verify that the pulleys are the correct diameter or width. Using a known good vehicle compare the pulley sizes.

Drive Belt Vibration


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 7
Chevrolet Venture V6-3.4L VIN E 149

Diagnostic Aids
The accessory drive components can have an affect on engine vibration. Such as but not limited to the A/C system over charged, the power
steering system restricted or the incorrect fluid, or an extra load on the generator. To help identify an intermittent or an improper condition, vary
the loads on the accessory drive components.

Test Description
The number(s) below refer to the step number(s) on the diagnostic table.
2. This test is to verify that the symptom is present during diagnosing. Other vehicle components may cause a similar symptom such as the
exhaust system, or the drivetrain.
3. This test is to verify that the drive belt(s) or accessory drive components may be causing the vibration. When removing the drive belt the
water pump may not be operating and the engine may overheat. Also DTCs may set when the engine is operating with the drive belt
removed.
4. The drive belt(s) may cause a vibration. While the drive belt(s) is removed this is the best time to inspect the condition of the belt.
6. Inspecting of the fasteners can eliminate the possibility that a wrong bolt, nut, spacer, or washer was installed.
8. This step should only be performed if the water pump is driven by the drive belt. Inspect the water pump shaft for being bent. Also inspect
the water pump bearings for smoothness and excessive play. Compare the water pump with a known good water pump.
9. Accessory drive component brackets that are bent, cracked, or loose may put extra strain on that accessory component causing it to vibrate.

Drive Belt Whine


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 8
Chevrolet Venture V6-3.4L VIN E 150

Diagnostic Aids
The drive belt(s) will not cause the whine noise.
If the whine noise is intermittent, verify the accessory drive components by varying their loads making sure they are operated to their maximum
capacity. Such items but not limited to may be an A/C system overcharged, the power steering system restricted or the wrong fluid, or the
generator failing.

Test Description
The number(s) below refer to the step number(s) on the diagnostic table.
3. This test is to verify that the noise is being caused by the drive belt(s) or the accessory drive components. When removing the drive belt the
water pump may not be operating and the engine may overheat. Also DTCs may set when the engine is operating with the drive belt
removed.
4. The inspection should include checking the drive belt tensioner and the drive belt idler pulley bearings. The drive belt(s) may have to be
installed and the accessory drive components operated separately by varying their loads. Refer to the suspected accessory drive component
for the proper inspection and replacement procedure.
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 1
Chevrolet Venture V6-3.4L VIN E 151
Drive Belt Tensioner: Testing and Inspection
1. Inspect the drive belt tensioner pulley. Ensure that the drive belt tensioner pulley is vertically aligned with the other accessory drive pulleys.
If the drive belt tensioner pulley is NOT vertically aligned with the other accessory drive pulleys, replace the drive belt tensioner. Refer to
Drive Belt Replacement.
2. Ensure that the drive belt tensioner moves freely. Insert a breaker bar or ratchet into the tensioner in order to rotate the tensioner
counterclockwise, then slowly lower the drive belt tensioner pulley to the drive belt. If the drive belt tensioner binds or does not move freely,
replace the drive belt tensioner. Refer to Drive Belt Tensioner Replacement.
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 1
Chevrolet Venture V6-3.4L VIN E 152
Engine Lubrication: Description and Operation

Front View
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 2
Chevrolet Venture V6-3.4L VIN E 153

Rear View
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 3
Chevrolet Venture V6-3.4L VIN E 154

Right View

Full pressure lubrication, through a full flow oil filter, is furnished by a gear type oil pump. The oil is drawn up through the pickup screen and the
tube. The oil passes through the pump to the oil filter.

The oil filter is a full flow paper element unit. An oil filter bypass is used in order to ensure oil supply during the following conditions:
^ On a cold start
^ If the filter is plugged
^ If the filter develops excessive pressure drop

The bypass is designed to open at 69 - 83 kPa (10 - 12 psi).

A new priority oil delivery system supplies oil first to the crankshaft journals. The oil from the crankshaft main bearings is supplied to the
connecting rod bearings by intersecting the passages drilled in the crankshaft. The passages supply the oil to the crankshaft main bearings and the
camshaft bearings through the intersecting vertical drilled holes. The oil passages from the camshaft journals supply oil to the hydraulic lifters.

The hydraulic lifters pump oil up through the pushrods to the rocker arms. The cast dams in the crankcase casting direct the oil that drains back
from the rocker arms in order to supply the camshaft lobes. The camshaft chain drive is lubricated by indirect oil splash.
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 1
Chevrolet Venture V6-3.4L VIN E 155
Engine Oil Pressure: Testing and Inspection
Low or No Oil Pressure
The following conditions may cause low or no oil pressure:
^ Low oil level
Fill to the full mark on the oil level indicator.
^ Incorrect or malfunctioning oil pressure switch
Replace the oil pressure switch.
^ Incorrect or malfunctioning oil pressure gauge
Replace the oil pressure gauge.
^ Improper oil viscosity or diluted oil
- Install oil of proper viscosity for expected temperature.
- Install new oil if the oil is diluted.
^ A worn or dirty oil pump
Clean or replace the oil pump.
^ A plugged oil filter
Replace the oil filter.
^ A loose or plugged oil pickup screen
Replace the oil pickup screen.
^ A hole in the oil pickup tube
Replace the oil pickup tube.
^ Excessive bearing clearance
Replace the bearings.
^ Cracked, porous, or plugged oil gallery
Repair or replace the engine block.
^ Missing or improperly installed gallery plugs
Install or repair the plugs as needed.
^ A stuck pressure regulator valve
- Inspect the pressure regulator valve for sticking in the bore.
- Inspect the bore for scoring and burrs.
^ A worn or poorly machined camshaft
Replace the camshaft.
^ Worn valve guides
Repair the valve guides as needed.

Oil Pressure Testing

^ Tools Required
- J 25087-C Oil Pressure Test Kit

If the vehicle has low oil pressure complete the following steps:
1. Inspect the oil level.
2. Raise and support the vehicle. Refer to Vehicle Lifting.
3. Remove the oil filter.
4. Assemble the plunger valve in the large hole of the J 25087-C base. Insert the hose in the small hole of the J 25087-C base. Connect the
gauge to the end of the hose.
5. Insert the flat side of the rubber plug in the bypass valve without depressing the bypass valve.
6. Install the J 25087-C on the filter mounting pad.
7. Start the engine.
8. Inspect the overall oil pressure, the oil pressure switch, and for noisy lifters. Ensure that the engine is at operating temperature before
inspecting the oil pressure. The oil pressure should be approximately 414 kPa (60 psi) at 1,850 RPM using 5W-30 engine oil.
9. If adequate oil pressure is indicated, test the oil pressure switch.
10. If a low reading is indicated, press the valve on the tester base in order to isolate the oil pump and/or its components from the lubricating
system, An adequate reading at this time indicates a good pump and the previous low pressure was due to worn bearings, etc. A low reading
while pressing the valve indicates a faulty pump.
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 1
Chevrolet Venture V6-3.4L VIN E 156
Oil Level Warning Indicator: Description and Operation

The PCM monitors the engine oil level switch signal at start-up to determine if the engine oil is OK. If the PCM determines that a low oil level
condition exists, the PCM will communicate the information over the Class II circuit to the IPC and it will illuminate the indicator lamp.
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 1
Chevrolet Venture V6-3.4L VIN E 157
Oil Pressure Sensor: Description and Operation

The PCM monitors the engine oil pressure switch (1) signal to determine if the engine oil pressure is Ok. If the PCM determines that a low oil
pressure condition exists, the PCM will communicate the information over the Class II circuit to the IPC and it will illuminate the indicator lamp.
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 1
Chevrolet Venture V6-3.4L VIN E 158
Crankshaft Main Bearing Seal: Service and Repair
Removal Procedure

1. Remove the transaxle. Refer to Transmission Replacement in Transmission and Drivetrain.


2. Remove the engine flywheel. Refer to Engine Flywheel Removal.
3. Remove the crankshaft rear oil seal.

Important: Do not damage the crankshaft or seal bore.

4. Pry out the crankshaft rear oil seal out using a suitable tool.

Installation Procedure

^ Tools Required
- J 34686 Crankshaft Rear Oil Seal Installer

1. Apply engine oil to the inside diameter and the outside diameter of the new crankshaft rear oil seal.
2. Slide the crankshaft rear oil seal over the mandrel until the back of the crankshaft rear oil seal bottoms squarely against the collar of the tool.
3. Perform the following steps in order to install the crankshaft rear oil seal:
3.1. Align the dowel pin of the J 34686 with the dowel pin in the crankshaft.

Notice: Refer to Fastener Notice in Service Precautions.

3.2. Attach the J 34686 to the crankshaft by hand, or tighten attaching screws to 5 Nm (45 inch lbs.).
3.3. Turn the T-handle of the J 34686 in order to engage allow the collar to push the seal into the bore.
Turn the handle until the collar is tight against the case. Ensure that the seal is seated properly.
3.4. Loosen the T-handle until the T-handle comes to a stop.
3.5. Remove the attaching screws.
4. Install the engine flywheel. Refer to Engine Flywheel Installation.
5. Install the transaxle. Refer to Transmission Replacement in Transmission and Drivetrain.
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 1
Chevrolet Venture V6-3.4L VIN E 159
Front Crankshaft Seal: Service and Repair
Removal Procedure

1. Remove the crankshaft balancer. Refer to Crankshaft Balancer Replacement.


2. Pry out the crankshaft front oil seal using a suitable tool. Use care not to damage the engine front cover or the crankshaft.
3. Inspect the crankshaft, the crankshaft balancer and the engine front cover for wear and/or damage. Replace the components as necessary.
Refer to the following procedures:
^ Crankshaft Balancer Clean and Inspect
^ Engine Front Cover Clean and Inspect

Installation Procedure

^ Tools Required
- J 35468 Crankshaft Front Oil Seal Installer

1. Align the J 35468 and the crankshaft front oil seal with the engine front cover and crankshaft.
2. Install the crankshaft front oil seal using the J 35468 and a suitable tool.
3. Install the crankshaft balancer. Refer to Crankshaft Balancer Replacement.
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 1
Chevrolet Venture V6-3.4L VIN E 160
Cooling System: Description and Operation

Air Baffles and Seals Description


A deflector redirects air flow. Deflectors are installed under the vehicle and redirects the air flow beneath the vehicle to flow through the cooling
system and increase radiator cooling.

Air baffles are used to direct air into the radiator and A/C condenser. Air seals ensure that air passes through, and does not bypass, the radiator
and the A/C condenser. A missing, damaged, or incorrectly installed baffle or seal may cause the engine to overheat.
Coolant
Notice: Antifreeze can be added to raise the boiling point of the coolant, but too much will affect the freezing point. Do not use a solution
stronger than 70 percent antifreeze, as the freeze level rises rapidly after this point. Pure antifreeze will freeze at -22°C (-8°F).
This vehicle as a newly developed engine coolant. GM Goodwrench DEX-COOL (R) was developed in order to last for 240,000 km (150,00
miles) or 5 years, whichever occurs first. Follow the instructions in Draining and Filling Cooling System. Use only GM Goodwrench
DEX-COOL (R) or HAVOLINE (R) DEX-COOL (R) when adding or changing the coolant.
A 50/50 mixture of ethylene glycol DEX-COOL (R) and water will provide the following protection:
^ Give freezing protection down to -37°C (-34°F)
^ Give boiling protection up to 129°C (265°F)
^ Protect against rust and corrosion
^ Help keep the proper engine temperature
^ Let the warning lights and gauges work as they should.

Coolant Heater Description


The engine heater is used to preheat the engine coolant for cold weather starting. The engine coolant heater operates from a 110-volt AC power
source and uses a heating element installed in the engine blocks water jacket. The heating element warms the coolant when the heater cord is
plugged into an AC power source.
The unit has a detachable electrical cord. If the heater fails to operate, check the cord connections and power supply before replacing the heating
element.

Coolant Level Module Description


Low Coolant Module
The low coolant module activates a light in the instrument cluster when the coolant in the radiator goes below a certain level. The low coolant
module is located in the radiator's right side tank.

Coolant Recovery System Description


Recovery Reservoir
The recovery reservoir is see-through, and is similar to the familiar windshield washer reservoir. The recovery reservoir is connected to the
radiator by a hose. The recovery reservoir collects the coolant that expands with rising temperature and would otherwise overflow from the
system. The coolant level should be at or above the COLD mark on the recovery reservoir cap overflow hose (inside the reservoir).

Cooling System Description


Cooling System
The cooling system maintains engine temperature at an efficient level during all engine operating conditions. When the engine is cold the system
cools slowly, or not at all, to allow the engine to warm up quickly.
The cooling system includes a radiator and coolant recovery subsystem, cooling fans, thermostat and housing, water pump, and drive belt.
Operation of the cooling system requires proper functioning of all components. Coolant is drawn from the radiator by the water pump and
circulated through coolant jackets in the engine block, intake manifold, and cylinder heads, and then directed back to the radiator where it is
cooled.
This system directs some coolant through hoses to the heater core, to provide for heating and defrosting. A recovery reservoir is connected to the
radiator to recover coolant displaced by expansion from high temperatures and maintain correct coolant level. As the coolant cools and contracts
it is drawn back into the radiator by vacuum.

Cooling System Circulation


The water pump is belt-driven. Coolant from the radiator outlet (lower right side of radiator) flows to the water pump inlet and is pumped
through coolant passages in the cylinder block and into the cavities surrounding the cylinder liners. Coolant then flows through holes in the
cylinder head gaskets into the cylinder head coolant passages and into the thermostat bypass system. Passages in the intake manifold direct the
coolant to the thermostat at the rear of the manifold. When the thermostat is closed (cold engine), the coolant is prevented from returning to the
radiator and is recirculated for quick engine warm-up.
Once the engine has warmed sufficiently, the thermostat opens and coolant flows to the inlet tank on the top left side of the radiator. It is cooled
as it flows across the horizontal core tubes to the outlet tanks on the right side of the radiator, completing the cycle.

Cooling Fan Relay


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 2
Chevrolet Venture V6-3.4L VIN E 161

Temperature Gauge
The temperature gauge replaces the warning lamp. The temperature switch is replaced with a transducer.

Coolant Temperature Fan Switch


The switch regulates voltage to the coolant fan relay, which operates the fan whenever the engine coolant temperature exceeds 110°C (230°F).
General Description

The electric cooling fans are used to lower the temperature of the engine coolant flowing through the radiator. They are also used to cool the
refrigerant (R-134a) flowing through the A/C condenser.
Operation
The electric cooling fan operates when the engine cooling temperature exceeds a certain value. The cooling fan on this engine is controlled by the
Powertrain Control Module (PCM). The PCM turns the cooling fan ON by grounding the coil of the cooling fan relays when certain conditions are
met. When the A/C is requested, the cooling fan will also be turned ON.

Power for the cooling fan motors are supplied through Maxifuses(R). The cooling fan relays are energized when current flows from the fuses in the
Underhood Accessory Wiring Junction Block, and through the relay coils to ground through the PCM. The Coolant Fan 1 Relay Control Circuit is
grounded for low speed fans operation. During low speed fans operation, both fans run at a slow speed. The Coolant Fan 1 Relay Control Circuit is
grounded for high speed operation. During high speed fans operation, both fans run at high speed.

IMPORTANT: When certain Diagnostic Trouble Codes (DTCs) are present, the PCM may command the cooling fans to run all the time. Perform
the A Powertrain On Board Diagnostic (OBD) System Check prior to diagnosing the engine cooling fans.

For more information regarding the Charging System, refer to Charging System Description, and Charging System Circuit Description in
Starting and Charging.

If a problem that involves the low speed cooling fan relay control circuit exists, DTC P0480 Cooling Fan Relay 1 Control Circuit should set. If the
problem affects the high speed cooling fan relay control circuit, DTC P0481 Cooling Fan Relay 2 Control Circuit should set. A problem with the
ECT sensor should set DTC P0117 Engine Coolant Temperature (ECT) Sensor Circuit Low Voltage, DTC P0118 Engine Coolant Temperature
(ECT) Sensor Circuit High Voltage, DTC P1114 Engine Coolant Temperature (ECT) Sensor Circuit Intermittent Low Voltage, DTC P1115 Engine
Coolant Temperature (ECT) Sensor Circuit Intermittent High Voltage. Any of these DTCs will affect cooling fan operation and should be
diagnosed before using the Electric Cooling Fan Diagnosis.

For more information regarding the Cooling System refer to Engine Cooling Fan Description - Electric, and Cooling System Description in
Cooling System.
Hot Coolant Temperature Indicator
The engine coolant temperature (ECT) sensor is a thermistor mounted in the engine coolant stream. The powertrain control module (PCM)
monitors the ECT to determine the engine coolant temperature. As the coolant temperature rises, the resistance of the ECT varies. If the coolant
temperature exceeds an acceptable level, the PCM detects this change and sends a class 2 message to the instrument panel cluster (IPC). The IPC
then illuminates the HOT COOLANT TEMP message.

Hot Coolant Temperature Indicator Circuit


The engine coolant temperature (ECT) sensor is a thermistor mounted in the engine coolant stream. The powertrain control module (PCM) monitors
the ECT to determine the engine coolant temperature. The ECT is grounded by the PCM through circuit 469. As the coolant temperature rises, the
resistance of the ECT varies. If the coolant temperature exceeds an acceptable level, the PCM detects this change at circuit 410 and sends a class 2
message through the serial data line to the instrument panel cluster (IPC). The IPC then illuminates the HOT COOLANT TEMP message.
Low Coolant Level Indicator
The engine coolant level module is located in the radiator's right side tank and monitors the engine coolant level. When the coolant level falls below
an acceptable level, the module acts like a switch and closes. The instrument panel cluster then illuminates the LOW COOLANT LEVEL message.
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 3
Chevrolet Venture V6-3.4L VIN E 162

Low Coolant Level Indicator Circuit


The engine coolant level module is located in the radiator's right side tank and monitors the engine coolant level. Ground is applied at all times from
G113 to the engine coolant level module through circuit 451. When the coolant level falls below an acceptable level, the module acts like a switch
and closes. Ground is then applied from the module through circuit 68 to the IPC. The instrument panel cluster illuminates the LOW COOLANT
LEVEL message.

Pressure Cap

Radiator Filler Cap

The crossflow radiator uses a pressure-vent filler cap to allow a buildup of 103 kPa (15 psi) in the cooling system. The cap allows the system to
operate at a higher than atmospheric pressure. This pressure raises the boiling point of the coolant to about 129°C (265°F) at sea level, which
increases the cooling efficiency of the radiator.
The pressure-type cap contains a blowoff (pressure) valve (2) and a vacuum (atmospheric) valve (1). A spring of pre-determined strength holds
the pressure valve against the valve's seat. This spring protects the radiator by relieving any pressure that exceeds design limits. A spring holds
the vacuum valve against the valve's seat which permits opening of the valve in order to relieve vacuum created in the system when the system
cools. This prevents radiator collapse.

Caution: To avoid being burned, do not remove the radiator cap or surge tank cap while the engine is hot. The cooling system will
release scalding fluid and steam under pressure if radiator cap or surge tank cap is removed while the engine and radiator are still hot.

Caution: As long as there is pressure in the cooling system, the temperature can be considerably higher than the boiling temperature of
the solution in the radiator without causing the solution to boil. Removal of the pressure cap while the engine is hot and pressure is high
will cause the solution to boil instantaneously - possibly with explosive force - spewing the solution over the engine, fenders and the
person removing the cap.

The radiator cap is designed to discourage unintentional removal. Safely remove the cap in the following way:
1. Slowly rotate the cap counterclockwise, do not press down, to the detent.
2. Allow any residual pressure, indicated by a hissing sound, to be relieved.
3. After the hissing stops, continue to rotate the cap counterclockwise until the cap is removed.
The following is embossed on the cap:
^ A caution regarding opening of the cap
^ Arrows that indicate the proper closed position

Radiator Assembly Description


These engines use a cross-flow, lightweight aluminum and plastic radiator.
^ A brazed aluminum tube and center core.
^ Two plastic end tanks.
^ A transmission oil cooler.
^ An engine oil cooler.
^ A radiator drain plug.

Clinch tabs fasten the end tanks to the core. A high temperature rubber gasket seals each of the end tanks. The right side end tank houses the
transmission oil cooler. The left side end tank houses the engine oil cooler. Rubber gaskets and nuts seal the oil cooler fittings to the end tanks. The
drain cock is plastic and this is at the bottom of the left side end tank.
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 4
Chevrolet Venture V6-3.4L VIN E 163

Cross-Flow Radiator Core and Outlet and Inlet Tanks


These models have an aluminum, cross-flow design core (1). The core uses a stack of horizontal tubes (2) that resist plugging. The cooling fins
(3) surround these tubes. The top and bottom ribs strengthen the assembly. The saw-cut in each strengthening rib allows for expansion during
temperature changes.
The inlet and the outlet tanks are molded from high-temperature, nylon reinforced plastic. A high-temperature rubber gasket seals the tank flange
around the edge. The inlet and the outlet tanks are clamped to the right side and the left side of the core with clinch tabs. These tabs are part of
the aluminum header at each end of the core. Radiators used with automatic transmissions have transmission oil coolers with inlet and outlet
fittings for transmission fluid circulation.
You can identify an aluminum-plastic radiator by the black plastic side tanks and an aluminum radiator core.

Engine Oil Cooler


The 3100 (L82) engine comes with an optional engine oil cooler which uses engine coolant flowing through an oil cooler at the oil filter.

Radiator Drain Cock


The radiator drain cock is on the bottom, left side of the radiator end tank. The drain cock includes the drain cock and the drain cock seal. Use
the drain cock when you drain the coolant.

Thermostat Description
The thermostat is a coolant flow control component that utilizes a temperature sensitive wax-pellet element.

The lower end of the thermostat, containing the element, is installed in the engine water jacket.

The thermostat performs the following functions:


^ Controls the flow of coolant through the radiator
^ Enables controlled engine warm-up
^ Assists in coolant temperature control

The wax pellet element (4) in the thermostat expands when heated, and contracts when cooled.

The element connects through a piston (1) to a thermostat valve (2).

When the element is heated, pressure is exerted against a rubber diaphragm (3) which forces the thermostat valve to open. As the element is cooled,
the contraction allows a spring (5) to close the thermostat valve.

While the coolant is cold, the thermostat valve remains closed. This prevents circulation of coolant through the radiator. At this point, coolant is
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 5
Chevrolet Venture V6-3.4L VIN E 164
only allowed to circulate throughout the engine block and heater core in order to allow the engine to warm quickly.

As the engine warms, the element expands and the thermostat valve opens. This permits coolant to flow through the radiator, where the heat
dissipates to the atmosphere.

Throttle Body Coolant System Description


The throttle body cooling system assists in maintaining the proper temperature of the throttle body under various ambient conditions. Engine
coolant flows around the throttle body via passages in the casting. During initial start up, the throttle body cooling system assists in warming the
throttle body. During normal operating temperatures, the throttle body cooling system assists in keeping the throttle body cool.

Transmission Oil Cooler Description


Transaxle Oil Cooler
The transaxle oil cooler is in the right side end tank of the radiator. You can replace the oil cooler by removing the tank from the core. This cools
the transaxle oil that flows through the cooler.

Water Pump Description


The coolant pump is a centrifugal-type pump that consists of the following components:
^ An impeller
^ An impeller driveshaft
^ A pulley flange
^ A cast housing The back side of the drive belt drives the pulley. The pulley attaches to the pump.
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 1
Chevrolet Venture V6-3.4L VIN E 165
Cooling System: Initial Inspection and Diagnostic Overview

Diagnostic Starting Point


Begin the system diagnosis with the A Diagnostic System Check. The Diagnostic System Check will provide the following information:

^ The identification of the control module(s) which command the system.

^ The ability of the control module(s) to communicate through the serial data circuit.

^ The identification of any stored diagnostic trouble codes (DTCs) and their status. The use of the Diagnostic System Check will identify the
correct procedure for diagnosing the system and where the procedure is located.

Diagnostic System Check

Test Description
The number(s) below refer to the step number(s) on the diagnostic table.
2. Lack of communication may be due to a partial malfunction of the class 2 serial data circuit or due to a total malfunction of the class 2 serial
data circuit. The specified procedure will determine the particular condition.
3. The symptom list in Symptoms will determine the correct diagnostic procedure to use.
4. The presence of DTCs which begin with "U" indicate that loss of Class 2 communications has occurred.
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 1
Chevrolet Venture V6-3.4L VIN E 166
Cooling System: Symptom Related Diagnostic Procedures

A Symptoms - Engine Cooling


Important: The following steps must be completed before using the symptom tables.

1. Perform the A Diagnostic System Check before using the Symptom Tables in order to verify that all of the following are true:
^ There are no DTCs set.
^ The control module(s) can communicate via the serial data link.
2. Review the system operation in order to familiarize yourself with the system functions. Refer to:
^ Hot Coolant Temperature Indicator Operation
^ Hot Coolant Temperature Indicator Circuit Description
^ Low Coolant Level Indicator Operation
^ Low Coolant Level Indicator Circuit Description

Visual/Physical Inspection
^ Inspect for aftermarket devices which could affect the operation of the Cooling System System. Refer to Checking Aftermarket Accessories
in Diagrams/Diagnostic Aids.
^ Inspect the easily accessible or visible system components for obvious damage or conditions which could cause the symptom.
^ Inspect the cooling system for the proper coolant level.

Intermittent
Faulty electrical connections or wiring may be the cause of intermittent conditions. Refer to Testing for Intermittent and Poor Connections in
Diagrams/Diagnostic Aids.

Symptom List
Refer to a symptom diagnostic procedure from the following list in order to diagnose the symptom:
^ HOT COOLANT TEMP Message Always On
See: Hot Coolant Temp Message Always On

^ HOT COOLANT TEMP Message Inoperative


See: Hot Coolant Temp Message Inoperative

^ LOW COOLANT LEVEL Message Always On


See: Low Coolant Level Message Always On

^ LOW COOLANT LEVEL Message Inoperative


See: Low Coolant Level Message Inoperative
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 2
Chevrolet Venture V6-3.4L VIN E 167

Engine Overheating
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 3
Chevrolet Venture V6-3.4L VIN E 168
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 4
Chevrolet Venture V6-3.4L VIN E 169

Loss of Coolant
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 5
Chevrolet Venture V6-3.4L VIN E 170
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 6
Chevrolet Venture V6-3.4L VIN E 171
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 1
Chevrolet Venture V6-3.4L VIN E 172
Cooling System: Component Tests and General Diagnostics

Non-Trouble Code Procedures


Leak Testing
1. Add water to the radiator to detect core leaks. Clean the core in order to make it easier to find the damaged area.
2. Remove dirt and insects from the fins with a common water hose without a nozzle. Excessive water pressure could damage the fins.
3. Scrub the core with a soft-bristle brush. Use clean hot water or hot water with a mild detergent solution.

On-Vehicle Testing

^ Tools Required
- J 24460-01 Cooling System Tester

1. Pressure test the aluminum/plastic radiator using a common pump and gage.
2. Make sure the cooling system is at a cool temperature, then remove the radiator cap.

3. Connect the gage and apply normal system operating pressure. Do not exceed 138 kPa (20 psi).
4. Watch the gage needle for an indication of a leak.
5. Examine the radiator and other cooling system parts for signs of escaping coolant.
6. Repair all hose and hose connections as required.
7. Check the radiator cap to ensure that it will maintain the correct pressure.
8. If the radiator is leaking during the pressure test, mark the leak area in order to find the leak once the radiator is removed.

Off-Vehicle Testing

Notice: Never use compressed air to pressure test a radiator that is not regulated to 138 kPa (20 psi). Pressures over 138 kPa (20 psi.) will
damage the radiator.

Do not use the boil-out tanks or vats or other tanks that have been used for copper and brass radiators. The flux, acid and caustic cleaners
remaining in these tanks will attack the aluminum and cause radiator failure. A separate test tank containing clean water is strongly recommended
for servicing an aluminum/plastic radiator.

1. Install the test fittings or rubber test caps in the inlet and outlet necks and seal the oil cooler footings with metal plugs. This will protect the
cooler and keep the fluid from running out.
2. Attach the pressure tester and gradually apply air pressure.
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 2
Chevrolet Venture V6-3.4L VIN E 173
^ Do not exceed 138 kPa (20 psi).
^ Check pressure gage to see if there is a pressure loss.
^ To ensure that there are no small leaks, run water over the repair area and look for bubbles. (A mild detergent is very helpful.)
^ If a large water tank is available, submerge the radiator and check for bubbles at the following locations:
- Inlet tank (1)
- Core tubes (2)
- Outlet tank (3)
- Oil cooler connections (4)
- Drain plug (5)

Coolant Concentration Testing


^ Tools Required
- J 23688 Coolant Tester (Fahrenheit Scale)
- J 26568 Coolant Tester (Centigrade Scale)

Some coolant manufacturers mix other types of glycol into their coolant formulations. Propylene glycol is the most common new ingredient.

A hydrometer does not always provide a correct measurement of freeze protection when anything other than ethylene glycol and water is being
tested. The degree of inaccuracy varies depending on the proportion of other glycols present in the coolant.

All new GM vehicles are produced with coolant that can be accurately measured with a hydrometer; however, when the type and quality of coolant
being measured is unknown, such as a customer vehicle that has accumulated mileage, the use of a refractometer is recommended.

Coolant testers J 26568 (Centigrade Scale) or J 23688 (Fahrenheit Scale) can be used to check the antifreeze protection of the coolant. Make sure
the refractometer markings are correct. Unless J 26568 or J 23688 has a provision for temperature correction, test the temperature at which J 26568
or J 23688 is calibrated. If the coolant is warmer or cooler, the reading may be incorrect. Follow the manufacturers' directions on using J 26568 or J
23688.

Important:
^ Before each use, swing back the plastic cover at the slanted end of the coolant tester, exposing the measuring window and the bottom of
the plastic cover.
^ Wipe the measuring window dry with a tissue or a clean, soft cloth.
^ Close the plastic cover.
^ Do not remove the clear plastic pump from the J 23688 or the J 26568.

1. Release the tip of the pump from the housing of the J 23688 or the J 26568.
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 3
Chevrolet Venture V6-3.4L VIN E 174

2. Insert the tip of the pump into the radiator filler neck. The tip of the pump must be below the level of the coolant.
3. Press the bulb. Release the pump bulb in order to obtain a sample of the coolant.
4. Insert the tip of the pump into the cover plate opening.
5. Press the pump bulb. Allow a few drops to fall onto the measuring surface. Do not open the plastic cover when taking readings because any
water evaporation will change the reading.

6. Point the coolant concentration tester toward any light source. Look into the eyepiece.
^ The coolant protection reading is at the point where the dividing line between light and dark crosses the scale. Antifreeze protection is the
scale on the right.
^ The temperature scale is reversed from a standard thermometer scale. Below zero readings are on the upper half of the scale.

7. If the readings are not clear, properly clean and dry the measuring surface. Conduct a new test.
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 4
Chevrolet Venture V6-3.4L VIN E 175

Pressure Testing the Pressure Cap


^ Tools Required
- J 24460-01 Cooling System Tester

Caution: To avoid being burned, do not remove the radiator cap or surge tank cap while the engine is hot. The cooling system will
release scalding fluid and steam under pressure if radiator cap or surge tank cap is removed while the engine and radiator are still hot.

1. Remove the radiator cap.


2. Wet the radiator cap gasket with water. Wash off any sediment from the sealing surface.
3. Install the cap to J 24460-01
4. Pump up the pressure to the pressure stamped on the cap by operating the plunger handle of J 24460-01
5. Note the rate of decrease in pressure.
6. The pressure reading should remain within the corresponding pressure segment of the scale for about 10 seconds.
7. If the cap does not hold the corresponding pressure, replace the cap.

Thermostat Diagnosis
Thermostat Test
The coolant thermostat can be tested using a temperature (tempil) stick. The temperature stick is a pencil like device. It has a wax material
containing certain chemicals which melt at a given temperature. Temperature sticks can be used to determine a thermostat's operating range, by
rubbing 87°C (188°F) and 97°C (206°F) sticks on the thermostat housing.

^ Tools Required
- J 24731-188 188'F Tempilstick
- J 24731-206 206OF Tempilstick
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 5
Chevrolet Venture V6-3.4L VIN E 176

1. Use a tempilstick in order to find the opening and the closing temperatures of the coolant thermostat.
^ J 24731-188 tempilstick melts at 87°C (188°F). The thermostat should begin to open.
^ J 24731-206 tempilstick melts at 97°C (206°F). The thermostat should be fully open.
2. Replace the coolant thermostat if it does not operate properly between this temperature range.
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 1
Chevrolet Venture V6-3.4L VIN E 177
Cooling System: Service and Repair
Draining and Filling Cooling System
Important: Do NOT add any engine coolant supplement sealant pellets to the cooling system.

Drain and refill the engine cooling system every five years or 240,000 km, (150,000 miles), whichever occurs first.

Draining Procedure

1. Park the vehicle on a level surface.


2. Remove and clean the coolant recovery reservoir.

Caution: Do not remove the radiator cap while the cooling system is hot. Serious personal injury may result. Only remove the
radiator cap from a cool engine.

3. Remove the radiator cap when the engine is cool:


3.1. Slowly rotate the cap counterclockwise to the detention tab. Do not press down while rotating pressure cap.
3.2. Wait until any residual pressure (indicated by a hissing sound) is relieved.
3.3. After all hissing stops, press down on the radiator cap and rotate the cap counterclockwise in order to remove the cap.

Important: Recover and store used coolant in a used coolant holding tank and submit the used coolant for recycling on a regular basis. Do
NOT pour used coolant down the drain! Ethylene glycol antifreeze is very toxic. Disposing of ethylene glycol into the sewer system or
ground water is both illegal and ecologically unsound!

4. Place a drain pan under the radiator drain valve in order to collect all of the used coolant.

5. Open the radiator drain valve located at the bottom of the radiator tank. If only partial cooling system draining is required, drain enough
coolant to perform the procedure.
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 2
Chevrolet Venture V6-3.4L VIN E 178

6. Open the air bleed valve on the thermostat housing two full turns.

7. Open the air bleed valve above coolant pump two full turns.
8. Place a drain pan under the engine block drains in order to collect the used coolant.

Important: Allow the coolant to drain completely.

9. Remove both of the engine block drains.


^ The front (left) engine block drain is located between the starter motor and the engine oil filter.
^ The rear (right) engine block drain is located near the crankshaft position sensor.

Filling Procedure
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 3
Chevrolet Venture V6-3.4L VIN E 179

1. Reinstall the engine block drains.

2. Close the radiator drain valve.

3. Install the coolant recovery reservoir.

Notice: When adding coolant, it is important that you use GM Goodwrench DEX-COOL (R) or HAVOLINE (R) DEX-COOL (R) coolant.
If Coolant other than DEX-COOL (R) or HAVOLINE (R) DEX-COOL (R) is added to the system the engine coolant will require change
sooner-at 50 000 km (30,000 mi) or 24 months.

4. Slowly add a 50/50 mixture of GM Goodwrench DEX-COOL (R) or HAVOLINE (R) DEX-COOL (R) and clean, drinkable water to the
radiator until the coolant level is at the base of the radiator fill neck.
5. Wait for two minutes and recheck the level of the coolant in the radiator. If necessary, add coolant to radiator until the coolant level is at the
base of the radiator fill neck.
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 4
Chevrolet Venture V6-3.4L VIN E 180

6. Install the radiator cap.

7. Ensure that the radiator cap arrow points toward the radiator overflow tube.

Important: The air bleed valves are brass. Do NOT over-tighten the air bleed valves.

8. Close the air bleed valve above coolant pump.


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 5
Chevrolet Venture V6-3.4L VIN E 181

9. Close the air bleed valve on the thermostat housing.


10. Fill the coolant reservoir with a 50/50 mixture of GM Goodwrench DEX-COOL (R) or HALVOLINE (R) DEX-COOL (R) and clean,
drinkable water.

Caution: Do not remove the radiator cap while the cooling system is hot. Serious personal injury may result. Only remove the
radiator cap from a cool engine.

Important: If coolant temperature indicator comes on. Turn the engine OFF immediately and allow the engine to cool. Do NOT remove the
radiator cap.

11. Start the engine and allow the engine cooling fan to cycle on and off three times.
If the low coolant indicator does not turn off and the coolant level is above the Full Cold mark on the coolant recovery reservoir, refer to
LOW COOLANT LEVEL Message Always On in Instrument Panel, Gauges and Warning Indicators.
12. Turn the ignition off.
13. Allow the engine to cool.
14. Ensure that the engine coolant concentration (freeze point) is sufficient. Refer to Coolant Concentration Testing.
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 1
Chevrolet Venture V6-3.4L VIN E 182
Cooling System: Service and Repair
Flushing
Important: Do NOT add any engine coolant supplement sealant pellets to the cooling system.

1. Park the vehicle on a level surface.


2. Remove and clean (flush) the coolant recovery reservoir. Refer to Coolant Recovery Reservoir Replacement.
3. Flush the engine cooling system. Follow the flushing equipment manufacturer's instructions.
4. Install the coolant recovery reservoir. Refer to Coolant Recovery Reservoir Replacement
5. Add the appropriate amount of GM Goodwrench DEX-COOL (R) or HAVOLINE (R) DEX-COOL (R) to the cooling system (50% of the
cooling system capacity). Refer to Cooling System System Specifications.
6. Fill the coolant recovery reservoir with a 1:1 DEX-COOL (R)/clean, drinkable water ratio.
7. Install the radiator cap (if removed). Ensure that the radiator cap arrow points toward the radiator overflow tube.

Caution: Do not remove the radiator cap while the cooling system is hot. Serious personal injury may result. Only remove the
radiator cap from a coot engine.

Important: If coolant temperature indicator comes on. Turn the engine OFF immediately and allow the engine to cool. Do NOT remove the
radiator cap.

8. Start the engine and allow the engine cooling fan to cycle on and off three times.
If the low coolant indicator does not turn off and the coolant level is above the Full Cold mark on the coolant recovery reservoir, refer to
LOW COOLANT LEVEL Message Inoperative in Instrument Panel, Gauges and Warning Indicators.
9. Turn the ignition off.
10. Allow the engine to cool.
11. Ensure that the engine coolant concentration (freeze point) is sufficient. Refer to Coolant Concentration Testing.
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 1
Chevrolet Venture V6-3.4L VIN E 183
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 1
Chevrolet Venture V6-3.4L VIN E 184
Auxiliary Water Pump: Service and Repair
Auxiliary Coolant Pump Replacement
AUXILIARY COOLANT PUMP REPLACEMENT

REMOVAL PROCEDURE

1. Drain the Cooling system. Refer to Draining and Filling Cooling System in Cooling System. See: Service and Repair/Draining and Filling
Cooling System
2. Disconnect the electrical connector from the auxiliary coolant pump.
3. Remove the auxiliary coolant pump to heater core inlet hose from the auxiliary coolant pump.
4. Remove the inlet pipe to auxiliary coolant pump hose from the coolant pump.

5. Remove the auxiliary coolant pump retaining clips.


6. Remove the auxiliary coolant pump from the diagonal brace.

INSTALLATION PROCEDURE
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 2
Chevrolet Venture V6-3.4L VIN E 185

1. Install the auxiliary coolant pump to the diagonal brace.


2. Install the auxiliary coolant pump retaining clips.
3. Install the inlet pipe to auxiliary coolant pump hose to the coolant pump.
4. Install the auxiliary coolant pump to heater core inlet hose to the auxiliary coolant pump.

5. Connect the electrical connector to the auxiliary coolant pump.


6. Refill the cooling system. Refer to Draining and Filling Cooling System in Cooling System. See: Service and Repair/Draining and Filling
Cooling System
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 1
Chevrolet Venture V6-3.4L VIN E 186
Auxiliary Water Pump: Service and Repair
Auxiliary Coolant Bypass Pump Switch Replacement

Removal

1. Turn the ignition OFF.


2. Open the hood.
3. Disconnect the electrical connector from the auxiliary coolant pump bypass switch.
4. Unclip the switch from the back side of the front bumper beam.
5. Remove the switch from the vehicle.

Installation

1. Install the auxiliary coolant pump bypass switch to the vehicle.


2. Clip the switch to the back side of the front bumper beam.
3. Connect the electrical connector to the switch.
4. Close the hood.
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 1
Chevrolet Venture V6-3.4L VIN E 187
Coolant Line/Hose: Service and Repair
Thermostat Bypass Pipes Replacement
Removal Procedure

1. Drain the cooling system. Refer to Draining and Filling Cooling System.
2. Remove the spark plug wire harness from the thermostat bypass pipe.
3. Remove the thermostat bypass pipe to throttle body nut.

4. Remove the thermostat bypass pipe to throttle body hose clamps (1).
5. Remove the thermostat bypass pipe to cylinder head nut (3).
6. Remove the thermostat bypass pipe bolt (4).
7. Remove the thermostat bypass pipe hose clamp (5).

8. Remove the thermostat bypass pipe hose.


9. Remove the thermostat bypass pipe.

Installation Procedure
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 2
Chevrolet Venture V6-3.4L VIN E 188

1. Apply engine coolant to the bypass pipe seal in order to ease installation.
2. Install the thermostat bypass pipe.
3. Install the thermostat bypass pipe hose.

4. Install the thermostat bypass pipe hose clamp (5).


5. Install the thermostat bypass pipe bolt (4).
^ Tighten the thermostat bypass pipe bolt to 11 Nm (98 inch lbs.).
6. Install the thermostat bypass pipe to cylinder head nut (3).
^ Tighten the thermostat bypass pipe nut to 25 Nm (118 ft. lbs.).
7. Install the thermostat bypass pipe to throttle body hose clamps (1).

8. Install the thermostat bypass pipe to throttle body nut.


^ Tighten the thermostat bypass pipe nut to 25 Nm (18 ft. lbs.).
9. Install the spark plug wire harness to the thermostat bypass pipe.
10. Fill the cooling system. Refer to Draining and Filling Cooling System.
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 1
Chevrolet Venture V6-3.4L VIN E 189
Coolant Line/Hose: Service and Repair
Throttle Body Heater Hose Replacement - Inlet
Removal Procedure

^ Tools Required
- J 38185 Hose Clamp Pliers

1. Remove the air cleaner and duct assembly. Refer to Air Filter Element Replacement in Computers and Controls.
2. Remove the throttle cable bracket in order to gain access to the throttle body heater hose clamp.
3. Drain the coolant until the coolant level is below the throttle body heater hoses. Refer to Draining and Filling Cooling System.
4. Use the J 38185 in order to remove the hose clamp.
5. Remove the throttle body heater inlet hose.

Installation Procedure

1. Install the throttle body heater inlet hose.


2. Use the J 38185 in order to install the hose clamps.
3. Install the throttle cable bracket.
4. Fill the cooling system. Refer to Draining and Filling Cooling System.
5. Install the air cleaner and duct assembly. Refer to Air Filter Element Replacement in Computers and Controls.
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 1
Chevrolet Venture V6-3.4L VIN E 190
Coolant Line/Hose: Service and Repair
Throttle Body Heater Hose Replacement - Outlet
Removal Procedure

^ Tools Required
- J 38185 Hose Clamp Pliers

1. Remove the air cleaner and duct assembly. Refer to Air Filter Element Replacement in Computers and Controls.
2. Drain the coolant until the coolant level is below the throttle body heater hoses. Refer to Draining and Filling Cooling System.
3. Use the J 38185 in order to remove the hose clamp.
4. Remove the throttle body heater outlet hose.

Installation Procedure

1. Install the throttle body heater outlet hose.


2. Use the J 38185 in order to install the hose clamps.
3. Fill the cooling system. Refer to Draining and Filling Cooling System.
4. Install the air cleaner and duct assembly. Refer to Air Filter Element Replacement in Computers and Controls.
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 1
Chevrolet Venture V6-3.4L VIN E 191
Coolant Reservoir: Service and Repair
Removal Procedure

1. Remove the reservoir hose clamp and the hose at the radiator overflow fitting.
2. Remove the mounting clips to the reservoir.
3. Remove the coolant reservoir.
4. Clean the coolant reservoir with soap and water. Rinse with clean water.

Installation Procedure

1. Install the coolant reservoir.


2. Install the mounting clips to the reservoir.
3. Lubricate the reservoir hose with clean water. Route the hose up to the radiator overflow fitting.
4. Install the clamp to the reservoir hose.
5. Refill the coolant reservoir. Refer to Draining and Filling Cooling System.
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 1
Chevrolet Venture V6-3.4L VIN E 192
Radiator Cooling Fan Motor: Description and Operation
General Description

The electric cooling fans are used to lower the temperature of the engine coolant flowing through the radiator. They are also used to cool the
refrigerant (R-134a) flowing through the A/C condenser.
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 1
Chevrolet Venture V6-3.4L VIN E 193
Radiator Cooling Fan Motor: Description and Operation
Operation
The electric cooling fan operates when the engine cooling temperature exceeds a certain value. The cooling fan on this engine is controlled by the
Powertrain Control Module (PCM). The PCM turns the cooling fan ON by grounding the coil of the cooling fan relays when certain conditions are
met. When the A/C is requested, the cooling fan will also be turned ON.

Power for the cooling fan motors are supplied through Maxifuses(R). The cooling fan relays are energized when current flows from the fuses in the
Underhood Accessory Wiring Junction Block, and through the relay coils to ground through the PCM. The Coolant Fan 1 Relay Control Circuit is
grounded for low speed fans operation. During low speed fans operation, both fans run at a slow speed. The Coolant Fan 1 Relay Control Circuit is
grounded for high speed operation. During high speed fans operation, both fans run at high speed.

IMPORTANT: When certain Diagnostic Trouble Codes (DTCs) are present, the PCM may command the cooling fans to run all the time. Perform
the A Powertrain On Board Diagnostic (OBD) System Check prior to diagnosing the engine cooling fans.

For more information regarding the Charging System, refer to Charging System Description, and Charging System Circuit Description in
Starting and Charging.

If a problem that involves the low speed cooling fan relay control circuit exists, DTC P0480 Cooling Fan Relay 1 Control Circuit should set. If the
problem affects the high speed cooling fan relay control circuit, DTC P0481 Cooling Fan Relay 2 Control Circuit should set. A problem with the
ECT sensor should set DTC P0117 Engine Coolant Temperature (ECT) Sensor Circuit Low Voltage, DTC P0118 Engine Coolant Temperature
(ECT) Sensor Circuit High Voltage, DTC P1114 Engine Coolant Temperature (ECT) Sensor Circuit Intermittent Low Voltage, DTC P1115 Engine
Coolant Temperature (ECT) Sensor Circuit Intermittent High Voltage. Any of these DTCs will affect cooling fan operation and should be
diagnosed before using the Electric Cooling Fan Diagnosis.

For more information regarding the Cooling System refer to Engine Cooling Fan Description - Electric, and Cooling System Description in
Cooling System.
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 1
Chevrolet Venture V6-3.4L VIN E 194
Radiator Cooling Fan Motor: Service and Repair
Removal Procedure

Caution: An electric fan under the hood can start up even when the engine is not running and can injure you. Keep hands, clothing and
tools away from any underhood electric fan.

Caution: To help avoid personal injury or damage to the vehicle, a bent, cracked, or damaged fan blade or housing should always be
replaced.

Important: If abnormal noise or vibration is felt from the engine compartment, inspect and clean any foreign material from the cooling fan
blades.

1. Turn the ignition off.


2. Remove the cooling fans with the cooling fan shroud. Refer to Cooling Fan Replacement -Electric.
3. Remove the cooling fan. Refer to Fan Replacement.
4. Remove the cooling fan motor electrical connector.
5. Remove the cooling fan motor screws.
6. Remove the cooling fan motor.

Installation Procedure

1. Install the cooling fan motor.

Notice: Refer to Fastener Notice in Service Precautions.

2. Install the cooling fan motor screws.


^ Tighten the screws to 6 Nm (53 inch lbs.).
3. Install the cooling fan motor electrical connector.
4. Install the cooling fan. Refer to Fan Replacement
5. Install the cooling fans with the cooling fan shroud. Refer to Cooling Fan Replacement - Electric.
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 1
Chevrolet Venture V6-3.4L VIN E 195
Fan Blade: Service and Repair
Fan Replacement
Removal Procedure

Caution: An electric fan under the hood can start up even when the engine is not running and can injure you. Keep hands, clothing and
tools away from any underhood electric fan.

Caution: To help avoid personal injury or damage to the vehicle, a bent, cracked, or damaged fan blade or housing should always be
replaced.

Important: If abnormal noise or vibration is felt from the engine compartment, inspect and clean any foreign material from the cooling fan
blades.

1. Turn the ignition off.


2. Remove the cooling fans with the cooling fan shroud. Refer to Cooling Fan Replacement - Electric.
3. Remove the cooling fan nut.
4. Remove the cooling fan.

Installation Procedure

1. Install the cooling fan.

Notice: Refer to Fastener Notice in Service Precautions.

2. Install the cooling fan nut.


^ Tighten the nut to 6 Nm (53 inch lbs.).
3. Install the cooling fans with the cooling fan shroud. Refer to Cooling Fan Replacement - Electric.
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 1
Chevrolet Venture V6-3.4L VIN E 196
Fan Blade: Service and Repair
Cooling Fan Replacement - Electric
Removal Procedure

Caution: An electric fan under the hood can start up even when the engine is not running and can Injure you. Keep hands, clothing and
tools away from any underhood electric fan.

Caution: To help avoid personal injury or damage to the vehicle, a bent, cracked, or damaged fan blade or housing should always be
replaced.

1. Turn the ignition off.


2. Remove the cooling fan harness electrical connector.
3. Loosen the engine mount strut bolts (engine side). Refer to Engine Mount Strut Bracket Replacement (Radiator Upper Support) or Engine
Mount Strut Bracket Replacement (Left Side) or Engine Mount Strut Bracket Replacement (Right Side).
4. Remove the engine mount strut bracket brace bolts from the upper radiator support and rotate the struts and brackets rearward. Refer to
Engine Mount Strut Bracket Replacement (Radiator Upper Support) or Engine Mount Strut Bracket Replacement (Left Side) or Engine
Mount Strut Bracket Replacement (Right Side).
5. Remove the air cleaner and duct assembly. Refer to Air Filter Element Replacement in Computers and Controls.
6. Remove the cooling fan shroud bolts.
7. Remove the transmission oil cooler lines from the transmission oil cooler line retainers.
8. Reposition the wiring harness at the upper radiator support in order to gain access.

9. Reposition and remove the cooling fans with the cooling fan shroud.

Installation Procedure
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 2
Chevrolet Venture V6-3.4L VIN E 197

1. Reposition the wiring harness at the upper radiator support in order to gain access.
2. Install the cooling fans with the cooling fan shroud.

Notice: Refer to Fastener Notice in Service Precautions.

3. Install the cooling fan shroud bolts.


^ Tighten the bolts to 6 Nm (53 inch lbs.).
4. Install the transmission oil cooler lines to the transmission oil cooler line retainers.
5. Install the air cleaner and duct assembly. Refer to Air Filter Element Replacement in Computers and Controls.
6. Install the engine mount strut bracket brace bolts from the upper radiator support and rotate the struts and brackets rearward. Refer to Engine
Mount Strut Bracket Replacement (Radiator Upper Support) or Engine Mount Strut Bracket Replacement (Left Side) or Engine Mount Strut
Bracket Replacement (Right Side).
7. Tighten the engine mount strut bolts (engine side). Refer to Engine Mount Strut Bracket Replacement (Radiator Upper Support) or Engine
Mount Strut Bracket Replacement (Left Side) or Engine Mount Strut Bracket Replacement (Right Side).

8. Install the cooling fan harness electrical connector.


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 1
Chevrolet Venture V6-3.4L VIN E 198
Coolant Temperature Sensor/Switch (For Computer): Description and Operation
The engine coolant temperature sensor is a thermistor (a resistor which changes value based on temperature) mounted in the engine coolant stream.

Low coolant temperature produces a high resistance (100,000 ohms at -40°C/-40°F) while high temperature causes low resistance (70 ohms at 130
°C/266°F).

The PCM supplies a 5 volt signal to the engine coolant temperature sensor through a resistor in the PCM and measures the voltage. The voltage is
high when the engine is cold, and low when the engine is hot. By measuring the voltage, the PCM calculates the engine coolant temperature. The
engine coolant temperature affects most systems the PCM controls.

The scan tool displays engine coolant temperature in degrees. After engine startup, the temperature should rise steadily to about 90°C (194°F) then
stabilize when thermostat opens. If the engine has not been run for several hours (overnight), the engine coolant temperature and intake air
temperature displays should be close to each other. A hard fault in the engine coolant sensor circuit should set DTC P0117 Engine Coolant
Temperature (ECT) Sensor Circuit Low Voltage, or DTC P0118 Engine Coolant Temperature (ECT) Sensor Circuit High Voltage. The DTC
Diagnostic Aids also contains a chart to check for sensor resistance values relative to temperature.
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 2
Chevrolet Venture V6-3.4L VIN E 199

The ECT sensor (3) also contains another circuit which is used to operate the engine coolant temperature gauge located in the instrument panel.
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 1
Chevrolet Venture V6-3.4L VIN E 200
Coolant Temperature Sensor/Switch (For Computer): Service and Repair

REMOVAL PROCEDURE
1. Turn OFF the ignition.
2. Relieve the coolant pressure.
3. Disconnect the Engine Coolant Temperature (ECT) sensor electrical connector.
4. Use a deep well socket and an extension in order to remove the sensor.

INSTALLATION PROCEDURE
1. Coat the ECT sensor threads with sealer GM P/N 9985253 or equivalent.

NOTE: Refer to Fastener Notice in Service Precautions.

2. Install the sensor in the engine.

Tighten
Tighten the sensor to 23 N.m (17 lb ft).

3. Connect the ECT sensor electrical connector.


4. Start the engine.
5. Inspect for leaks.
6. Inspect the coolant level.
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 1
Chevrolet Venture V6-3.4L VIN E 201
Fan Shroud: Service and Repair
Removal Procedure

Caution: An electric fan under the hood can start up even when the engine is not running and can injure you. Keep hands, clothing and
tools away from any underhood electric fan.

Caution: To help avoid personal injury or damage to the vehicle, a bent, cracked, or damaged fan blade or housing should always be
replaced.

Important: If abnormal noise or vibration is felt from the engine compartment, inspect and clean any foreign material from the cooling fan
blades.

1. Turn the ignition off.


2. Remove the cooling fans with the cooling fan shroud. Refer to Cooling Fan Replacement - Electric.
3. Remove the cooling fans. Refer to Fan Replacement.
4. Remove the cooling fan motors from the cooling fan shroud. Refer to Cooling Fan Motor Replacement - Electric.
5. Remove the cooling fan motor heat shields from the cooling fan shroud.

Installation Procedure

1. Install the cooling fan motor heat shields to the cooling fan shroud.
2. Install the cooling fan motors to the cooling fan shroud. Refer to Cooling Fan Motor Replacement - Electric.
3. Install the cooling fans. Refer to Fan Replacement.
4. Install the cooling fans with the cooling fan shroud. Refer to Cooling Fan Replacement -Electric.
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 1
Chevrolet Venture V6-3.4L VIN E 202
Heater Core: Service and Repair
Auxiliary Coolant Pump to Heater Core Inlet Hose Replacement
REMOVAL PROCEDURE

1. Drain the cooling system. Refer to Draining and Filling Cooling System in Cooling Systems. See: Service and Repair/Draining and Filling
Cooling System
2. Remove the wiper module cover.
3. Remove the air cleaner duct and cover.
4. Rotate the engine forward.

5. Disconnect the auxiliary coolant pump to heater core inlet hose (2) from the auxiliary coolant pump.
6. Disconnect the auxiliary coolant pump to heater core inlet hose (2) from the heater core inlet.

7. If equipped with RPO C34, Rear HVAC System, disconnect the auxiliary coolant pump to heater core inlet hose from the hose-T.
8. Remove the auxiliary coolant pump to heater core inlet hose (2).

INSTALLATION PROCEDURE
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 2
Chevrolet Venture V6-3.4L VIN E 203

1. Install the auxiliary coolant pump to heater core inlet hose (2).
2. Connect the auxiliary coolant pump to heater core inlet hose to the heater core inlet.

3. If equipped with RPO C34, Rear HVAC System, connect the auxiliary coolant pump to heater core inlet hose to the hose-T.
4. Connect the inlet pipe to auxiliary coolant pump hose to the auxiliary coolant pump.
5. Rotate the engine rearward to the proper position.
6. Install the air cleaner cover and duct.

7. Install the wiper module cover.


8. Refill the cooling system.

For a description of the RPO Code(s) shown in this article/image, refer to the RPO Code List found at Vehicle/Application ID See: Application
and ID/RPO Codes
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 1
Chevrolet Venture V6-3.4L VIN E 204
Heater Core: Service and Repair
Heater Case/Cover Replacement
REMOVAL PROCEDURE

1. Remove the right instrument panel insulator.


2. Remove the left instrument panel insulator.
3. Remove the lower center console.
4. Remove the console bracket.
5. Remove the floor duct brace
6. Remove the floor duct
7. Remove the screws retaining the heater core outlet cover.
8. Remove the heater core outlet cover.

9. Remove the screws retaining the heater core cover.


10. Remove the heater core cover.

INSTALLATION PROCEDURE

1. Install the heater core cover.

NOTE: Refer to Fastener Notice in Service Precautions.


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 2
Chevrolet Venture V6-3.4L VIN E 205

2. Install the heater core cover retaining screws.

Tighten
Tighten the screws to 1.6 N.m (14 lb in).

3. Install the heater core outlet cover.


4. Install the heater core outlet cover retaining screws.

Tighten
Tighten the screws to 1.6 N.m (14 lb in).

5. Install the floor duct.


6. Install the floor duct brace.
7. Install the floor duct brace retaining nuts.

Tighten
Tighten the nuts to 10 N.m (89 lb in).

8. Install the console bracket.


9. Install the lower center console.
10. Install the left instrument panel insulator.
11. Install the right instrument panel insulator.
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 1
Chevrolet Venture V6-3.4L VIN E 206
Heater Core: Service and Repair
Heater Core Replacement
REMOVAL PROCEDURE

TOOLS REQUIRED
J 38185 Hose Clamp Pliers

1. Remove the air cleaner cover and duct assembly.


2. Drain the cooling system. Refer to Draining and Filling Cooling System in Cooling System. See: Service and Repair/Draining and Filling
Cooling System
3. Disconnect the wiper linkage. Refer to Wiper Motor Crank Arm Replacement in Wiper Washer System. See: Wiper and Washer
Systems/Wiper Motor/Service and Repair/Wiper Motor Crank Arm Replacement
4. Disconnect both of the heater hoses from the heater core using the J 38185.
5. Remove the heater core outlet cover.

6. Remove the screws retaining the heater core cover.


7. Remove the heater core cover.
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 2
Chevrolet Venture V6-3.4L VIN E 207

8. Remove and discard the cavity (1), whistle (2), and permagum (3) seals from the heater core cover.

9. Remove and discard the heater core outer seal (5) from the heater core.

10. Remove the heater core retaining clamp screw (1).


11. Remove the heater core retaining clamp.
12. Remove the heater core pipe retainer clamp screw (2).

13. Remove the heater core from the HVAC module.


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 3
Chevrolet Venture V6-3.4L VIN E 208

14. Remove and discard the heater core lower seal (4) from the HVAC module case.

15. Remove and discard the heater core center seal (3) from the HVAC module case.

16. Remove and discard the heater core upper seal (2) from the HVAC module case.

17. Remove the heater core pipe retainer clamp from the heater core pipes.
Using a flat bladed tool, release the retaining tab and open the clamp.
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 4
Chevrolet Venture V6-3.4L VIN E 209

INSTALLATION PROCEDURE

1. Install the heater core pipe retainer clamp to the heater core pipes.
Align the depression in the clamp to the ridge on one of the heater core pipes, then close the clamp to secure.

2. Install new heater cores side seals (1) to the HVAC module case.

3. Install a new heater core upper seal (2) to the HVAC module case.

4. Install a new heater core center seal (3) to the HVAC module case.
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 5
Chevrolet Venture V6-3.4L VIN E 210

5. Install a new heater core lower seal (4) to the HVAC module case.

6. Install the heater core to the HVAC module case.

NOTE: Refer to Fastener Notice in Service Precautions.

7. Install the heater core pipe retaining clamp screw (2).

Tighten
Tighten the screw to 1.6 N.m (14 lb in).

8. Install the heater core retaining clamp.


9. Install the heater core retaining clamp screw (1).

Tighten
Tighten the screw to 1.6 N.m (14 lb in).
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 6
Chevrolet Venture V6-3.4L VIN E 211

10. Install a new heater core outer seal (5) to the heater core.

11. Install a new cavity (1), whistle (2), and permagum (3) seals to the heater core cover.

12. Install the heater core cover.


13. Install the heater core cover retaining the screws.

Tighten
Tighten the screws to 1.6 N.m (14 lb in).

14. Install the heater core outlet cover. Refer to Heater Core Cover Replacement. See: Heater Case/Cover Replacement
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 7
Chevrolet Venture V6-3.4L VIN E 212

15. Connect both of the heater hoses and the clamps to the heater core using the J 38185 positioning the clamps as indicated.
16. Install the wiper linkage. Refer to Wiper Motor Crank Arm Replacement in Wiper Washer System. See: Wiper and Washer Systems/Wiper
Motor/Service and Repair/Wiper Motor Crank Arm Replacement
17. Refill the coolant.
18. Install the air cleaner cover and duct assembly.
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 1
Chevrolet Venture V6-3.4L VIN E 213
Heater Core: Service and Repair
Heater Core Replacement - Auxiliary
REMOVAL PROCEDURE

1. Drain the cooling system. Refer to Draining and Filling Cooling System in Cooling System. See: Service and Repair/Draining and Filling
Cooling System
2. Raise and support vehicle. Refer to Lifting and Jacking the Vehicle in Vehicle Lifting.
3. Disconnect the heater hose quick disconnects.
4. Lower the vehicle.
5. Remove the left side rear quarter lower trim panel.

6. Remove the heater pipe bracket retaining screw.


7. Remove the heater pipe bracket.
8. Remove the heater pipe block fitting bolt.
9. Carefully push the heater pipes downward to disconnect the heater pipe block fitting from the heater core.
10. Remove the heater core retaining screws.

IMPORTANT: Carefully pull the heater core straight out from the HVAC module so not to damage the cooling fins of the heater core.
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 2
Chevrolet Venture V6-3.4L VIN E 214

11. Remove the heater core from the rear HVAC module.

INSTALLATION PROCEDURE

IMPORTANT: Carefully insert the heater core straight into the HVAC module so not to damage the cooling fins of the heater core.

1. Install the heater core to the rear HVAC module.

NOTE: Refer to Fastener Notice in Service Precautions.

2. Install the heater core retaining screws

Tighten
Tighten the heater core retaining screws to 1.6 N.m (14 lb in).

3. Carefully pull the heater pipes up and align the heater pipe block fitting to the heater core.

4. Install the heater pipe block fitting retaining bolt.


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 3
Chevrolet Venture V6-3.4L VIN E 215

Tighten
Tighten the heater pipe block fitting retaining bolt 16 N.m (12 lb ft).

5. Install the heater pipe bracket.


6. Install the heater pipe bracket retaining screw.

Tighten
Tighten the heater pipe bracket retaining screw 1.6 N.m (14 lb in).

7. Install the left side rear quarter lower trim panel.


8. Raise and support vehicle. Refer to Lifting and Jacking the Vehicle in Vehicle Lifting.

9. Connect the heater hose quick disconnects


10. Lower the vehicle
11. Refill the cooling system.
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 1
Chevrolet Venture V6-3.4L VIN E 216
Heater Hose: Service and Repair

Auxiliary Coolant Pump to Heater Core Inlet Hose Replacement


REMOVAL PROCEDURE

1. Drain the cooling system. Refer to Draining and Filling Cooling System in Cooling Systems. See: Service and Repair/Draining and Filling
Cooling System
2. Remove the wiper module cover.
3. Remove the air cleaner duct and cover.
4. Rotate the engine forward. Refer to Rotating the Engine for Service Access in Engine. See: Engine/Service and Repair/Removal and
Replacement

5. Disconnect the auxiliary coolant pump to heater core inlet hose (2) from the auxiliary coolant pump.
6. Disconnect the auxiliary coolant pump to heater core inlet hose (2) from the heater core inlet.

7. If equipped with RPO C34, Rear HVAC System, disconnect the auxiliary coolant pump to heater core inlet hose from the hose-T.
8. Remove the auxiliary coolant pump to heater core inlet hose (2).

INSTALLATION PROCEDURE
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 2
Chevrolet Venture V6-3.4L VIN E 217

1. Install the auxiliary coolant pump to heater core inlet hose (2).
2. Connect the auxiliary coolant pump to heater core inlet hose to the heater core inlet.

3. If equipped with RPO C34, Rear HVAC System, connect the auxiliary coolant pump to heater core inlet hose to the hose-T.
4. Connect the inlet pipe to auxiliary coolant pump hose to the auxiliary coolant pump.
5. Rotate the engine rearward to the proper position. Refer to Rotating the Engine for Service Access in Engine. See: Engine/Service and
Repair/Removal and Replacement
6. Install the air cleaner cover and duct.

7. Install the wiper module cover.


8. Refill the cooling system.

For a description of the RPO Code(s) shown in this article/image, refer to the RPO Code List found at Vehicle/Application ID See: Application
and ID/RPO Codes
Heater and A/C Pipe Repair - Auxiliary
Do not service the rear heater lines as a complete unit. Service the rear heater lines as a sectional repair.

You can obtain the different sections of line through GMSPO.


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 3
Chevrolet Venture V6-3.4L VIN E 218

TOOLS REQUIRED
J 41425 A/C Line Repair Kit

Use the J 41425 when any of the following actions damage the A/C or heater lines:
^ Rub-through
^ Collision damage
^ Leakage in the system

Follow the Straight Line Repair procedure in order to repair the type of damage described above.

If the A/C or heater lines have visible damage or a leak in a bend area, replace the lines. Section the lines in order to obtain the original line
shapes. Maintaining the original line shape will prevent vibrations and rub-through.

Follow the A/C Line Sectioning Repair procedure in order to repair any damage in a bend area.

STRAIGHT LINE REPAIR


1. If you are repairing the A/C lines, evacuate, charge and leak test the system. Refer to Refrigerant Recovery and Recharging. See: Heating
and Air Conditioning/Refrigerant/Service and Repair
2. If you are repairing the heater lines, drain the cooling system. Refer to Draining and Filling Cooling System in Cooling System. See: Service
and Repair/Draining and Filling Cooling System
3. Raise and support the vehicle. Refer to Lifting and Jacking the Vehicle in Vehicle Lifting.
4. Locate the area that requires repair.
5. Use a tubing cutter in order to cut the damaged line for repair.
6. Use the cleaning pad from the J 41425 in order to clean any burrs or grease. Be sure to clean at least 19 mm (.75 in) from the A/C line.
7. Use the LOK prep sealant in order to prep the A/C line.
8. Apply one drop of the J 41425-3 sealing compound to the outside of each end of the line.
9. Install the correct LOK fitting into the jaws:
9.1. Insert the line ends into the LOK fitting.
9.2. Rotate the LOK fitting one complete turn in order to evenly distribute the sealing compound around the lines.
10. Verify that the connector ends are positioned in the counter bores of the jaw.
11. Install the J 41425-1 tool over the connectors and the tubes.
12. Hold the tool body with a 1/8 breaker bar. Turn the forcing screw until both of the connector collars bottom on the center shoulder of the
LOK fitting.
13. Loosen the forcing screw. Remove the tool from the repaired line.
14. Verify that the LOK fitting is correctly installed.
15. Lower the vehicle.
16. If you drained the cooling system, refill the coolant.
17. If you are repairing the A/C lines, recharge and leak test the system. Refer to Refrigerant Recovery and Recharging. See: Heating and Air
Conditioning/Refrigerant/Service and Repair

A/C LINE SECTIONING REPAIR


1. If you are repairing the A/C lines, evacuate the system. Refer to Refrigerant Recovery and Recharging. See: Heating and Air
Conditioning/Refrigerant/Service and Repair
2. If you are repairing the heater lines, drain the cooling system.
3. Raise and support the vehicle. Refer to Lifting and Jacking the Vehicle in Vehicle Lifting.
4. Obtain a new A/C line for sectioning.
5. Scribe a mark on the damaged A/C line that will be cut.
6. Scribe a mark on the new line that will be sectioned.
7. Use a tubing cutter in order to cut both of the A/C lines.
8. Use the cleaning pad from the J 41425 in order to clean any burrs or grease. Be sure to clean at least 19 mm (.75 in) from the A/C line.
9. Use the LOK prep sealant in order to prep the A/C line.
10. Apply one drop of the J 41425-3 sealing compound to the outside of each line end.
11. Install the correct LOK fitting into the jaws:
11.1. Insert the line ends into the LOK fitting.
11.2. Rotate the LOK fitting one complete turn in order to evenly distribute the sealing compound around the lines.
12. Verify that the connector ends are positioned in the counter bores of the jaw.
13. Install the J 41425-1 tool over the connectors and the tubes.
14. Hold the tool body with a 3/8 breaker bar. Turn the forcing screw until both of the connector collars bottom on the center shoulder of the
LOK fitting.
15. Loosen the forcing screw. Remove the tool from the repaired line.
16. Verify that the LOK fitting is correctly installed.
17. Repeat Step 4 through Step 13 for the other end of the repair line.
18. Lower the vehicle.
19. If you drained the cooling system, refill the coolant.
20. If you are repairing the A/C lines, recharge and leak test the system. Refer to Refrigerant Recovery and Recharging. See: Heating and Air
Conditioning/Refrigerant/Service and Repair

MINIMUM TUBE LENGTH REQUIRED TABLE


When you section the A/C lines, ensure that the correct minimum length remains in the straight part of the line on both sides of the splice.
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 4
Chevrolet Venture V6-3.4L VIN E 219

Heater And A/C Pipe Repair - Auxiliary

HEATER AND A/C PIPE REPAIR - AUXILIARY


Heater Hose Replacement - Inlet
REMOVAL PROCEDURE

1. Remove the air cleaner cover and duct assembly.


2. Disconnect the wiper linkage. Refer to Wiper Motor Crank Arm Replacement in Wiper Washer Systems. See: Wiper and Washer
Systems/Wiper Motor/Service and Repair/Wiper Motor Crank Arm Replacement
3. Drain the cooling system. Refer to Draining and Filling Cooling System in Engine Cooling. See: Service and Repair/Draining and Filling
Cooling System
4. Disconnect the inlet hose (1) from the inlet pipe (2).

5. Disconnect the inlet hose from the heater core.


6. Remove the inlet hose.

INSTALLATION PROCEDURE
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 5
Chevrolet Venture V6-3.4L VIN E 220

1. Install the inlet hose.


2. Connect the inlet hose to the heater core and position the hose clamp as indicated.

3. Connect the inlet (1) hose to the inlet pipe (2).


4. Refill the coolant.
5. Connect the wiper linkage. Refer to Wiper Motor Crank Arm Replacement in Wiper Washer Systems. See: Wiper and Washer
Systems/Wiper Motor/Service and Repair/Wiper Motor Crank Arm Replacement
6. Install the air cleaner cover and duct assembly.
Heater Hose Replacement - Outlet
REMOVAL PROCEDURE

1. Remove the air cleaner cover and duct assembly.


2. Drain the cooling system. Refer to Draining and Filling Cooling System in Cooling System. See: Service and Repair/Draining and Filling
Cooling System
3. Disconnect the wiper linkage. Refer to Wiper Motor Crank Arm Replacement in Wiper Washer Systems. See: Wiper and Washer
Systems/Wiper Motor/Service and Repair/Wiper Motor Crank Arm Replacement
4. Disconnect the outlet hose (3) from the outlet pipe (4).
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 6
Chevrolet Venture V6-3.4L VIN E 221

5. Disconnect the outlet hose from the heater core.


6. Remove the outlet hose.

INSTALLATION PROCEDURE

1. Install the outlet hose.


2. Connect the outlet hose to the heater core and position the hose clamp as indicated.

3. Connect the outlet hose (3) to the outlet pipe (4).


4. Refill the cooling system.
5. Connect the wiper linkage. Refer to Wiper Motor Crank Arm Replacement in Wiper Washer Systems. See: Wiper and Washer
Systems/Wiper Motor/Service and Repair/Wiper Motor Crank Arm Replacement
6. Install the air cleaner cover and dust assembly.
Heater Pipe Replacement - Inlet
REMOVAL PROCEDURE
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 7
Chevrolet Venture V6-3.4L VIN E 222

1. Remove the air cleaner cover and duct assembly.


2. Drain the cooling system. Refer to Draining and Filling Cooling System in Cooling System. See: Service and Repair/Draining and Filling
Cooling System
3. Disconnect the inlet hose (1) from the inlet pipe (2).

4. Disconnect the electrical harness retainer from the inlet pipe bracket.

5. Disconnect the inlet pipe mounting nut.


6. Remove the inlet pipe by pulling pipe rearward to remove from thermostat housing.
7. Remove and discard the O-ring seal from the inlet pipe.

INSTALLATION PROCEDURE
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 8
Chevrolet Venture V6-3.4L VIN E 223

1. Install a new O-ring seal on the inlet pipe.


2. Install the inlet pipe into the thermostat housing.

NOTE: Refer to Fastener Notice in Service Precautions.

3. Install the inlet pipe mounting nut.

Tighten
Tighten the nut to 7 N.m (62 lb in).

4. Connect the electrical harness retainer to the inlet pipe bracket.

5. Connect the inlet hose (1) to the inlet pipe (2).


6. Refill the coolant.
7. Install the air cleaner cover and duct assembly.
Inlet Pipe to Auxiliary Coolant Pump Hose Replacement
REMOVAL PROCEDURE
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 9
Chevrolet Venture V6-3.4L VIN E 224

1. Drain Cooling system. Refer to Draining and Filling Cooling System in Cooling System. See: Service and Repair/Draining and Filling
Cooling System
2. Remove the wiper module cover.
3. Remove the air cleaner duct and cover.
4. Rotate the engine forward and secure. Refer to Rotating the Engine for Service Access in Engine. See: Engine/Service and Repair/Removal
and Replacement

5. Disconnect the inlet pipe to auxiliary coolant pump hose from the inlet pipe.
6. Disconnect the inlet pipe to auxiliary coolant pump hose from the auxiliary coolant pump (4).
7. Remove the inlet pipe to auxiliary coolant pump hose (3).

INSTALLATION PROCEDURE

1. Install the inlet pipe to auxiliary coolant pump hose (3).


2. Connect the inlet pipe to auxiliary coolant pump hose to the auxiliary coolant pump (4).
3. Connect the inlet pipe to auxiliary coolant pump hose to the inlet pipe.
4. Rotate the engine rearward to the proper position. Refer to Rotating the Engine for Service Access in Engine. See: Engine/Service and
Repair/Removal and Replacement
5. Install the air cleaner cover and duct.
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 10
Chevrolet Venture V6-3.4L VIN E 225

6. Install the wiper module cover.


7. Refill the cooling system.
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 1
Chevrolet Venture V6-3.4L VIN E 226
Radiator: Service and Repair
Radiator Air Baffle Assemblies and Deflectors
Removal Procedure

1. Raise and suitably support the vehicle. Refer to Vehicle Lifting.


2. Remove the radiator lower air deflector mounting bolts.
3. Remove the radiator lower air deflector.

Installation Procedure

1. Install the radiator lower air deflector.

Notice: Refer to Fastener Notice in Service Precautions.

2. Install the radiator lower air deflector mounting bolts.


^ Tighten the bolts to 20 Nm (15 ft. lbs.).
3. Lower the vehicle. Refer to Vehicle Lifting.
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 1
Chevrolet Venture V6-3.4L VIN E 227
Radiator: Service and Repair
Radiator Replacement
Removal Procedure

1. Remove air cleaner and duct assembly. Refer to Air Filter Element Replacement in Computers and Controls.
2. Drain the coolant. Refer to Draining and Filling Cooling System.
3. Loosen the engine mount strut-to-engine mount strut bracket bolts. Refer to Engine Mount Strut Bracket Replacement (Radiator Upper
Support) or Engine Mount Strut Bracket Replacement (Left Side) or Engine Mount Strut Bracket Replacement (Right Side).
4. Remove the engine mount strut bracket brace bolts from the upper radiator support and reposition the struts and brackets rearward. Refer to
Engine Mount Strut Bracket Replacement (Radiator Upper Support) or Engine Mount Strut Bracket Replacement (Left Side) or Engine
Mount Strut Bracket Replacement (Right Side).
5. Remove the cooling fans with the cooling fan shroud. Refer to Cooling Fan Replacement -Electric.
6. Remove the radiator upper hose from the radiator. Refer to Radiator Hose Replacement - Inlet.
7. Remove the radiator lower hose from the radiator. Refer to Radiator Hose Replacement - Outlet.
8. Remove the low coolant module. Refer to Coolant Level Module Replacement.
9. Disconnect the transaxle oil cooler lines from the radiator. Refer to Automatic Transmission Oil Cooler Pipes Replacement in Transmission
and Drivetrain.
10. Remove the radiator brackets and bolts.
11. Remove the radiator.

Installation Procedure

1. Install the radiator.

Notice: Refer to Fastener Notice in Service Precautions.

2. Install the radiator brackets and bolts.


^ Tighten the bolts to 24 Nm (18 ft. lbs.).
3. Connect the transaxle oil cooler lines to the radiator. Refer to Automatic Transmission Oil Cooler Pipes Replacement in Transmission and
Drivetrain.
4. Install the low coolant module. Refer to Coolant Level Module Replacement.
5. Install the radiator upper hose to the radiator. Refer to Radiator Hose Replacement - Inlet.
6. Install the radiator lower hose to the radiator. Refer to Radiator Hose Replacement - Outlet
7. Install the cooling fans with the cooling fan shroud. Refer to Cooling Fan Replacement - Electric.
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 2
Chevrolet Venture V6-3.4L VIN E 228
8. Reposition and install the engine mount strut bracket brace bolts to the upper radiator support. Refer to Engine Mount Strut Bracket
Replacement (Radiator Upper Support) or Engine Mount Strut Bracket Replacement (Left Side) or Engine Mount Strut Bracket Replacement
(Right Side).
9. Tighten the engine mount strut-to-engine mount strut bracket bolts. Refer to Engine Mount Strut Bracket Replacement (Radiator Upper
Support) or Engine Mount Strut Bracket Replacement (Left Side) or Engine Mount Strut Bracket Replacement (Right Side).

Notice: When adding coolant, it is important that you use GM Goodwrench DEX-C001 (R) or HAVOLINE(R) DEX-COOL (R) coolant. If
Coolant other than DEX-COOL (R) or HAVOLINE (R) DEX-C00L (R) is added to the system the engine coolant will require change
sooner-at 50,000 km (30,000 mi) or 24 months.

10. Fill the cooling system. Refer to Draining and Filling Cooling System.
11. Install the air cleaner and duct assembly. Refer to Air Filter Element Replacement in Computers and Controls.
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 1
Chevrolet Venture V6-3.4L VIN E 229
Radiator Drain Plug: Service and Repair
Removal Procedure

1. Raise the vehicle. Refer to Vehicle Lifting.


2. Drain the coolant. Refer to Draining and Filling Cooling System.
3. Pull the stem out of the radiator body.
4. Clean or replace the seal and the stem as necessary.

Installation Procedure

1. Install the stem to the radiator body.


2. Fill the cooling system. Refer to Draining and Filling Cooling System.
3. Lower the vehicle.
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 1
Chevrolet Venture V6-3.4L VIN E 230
Radiator Hose: Service and Repair
Radiator Hose Replacement - Inlet
Removal Procedure

^ Tools Required
- J 38185 Hose Clamp Pliers

1. Partially drain the coolant. Refer to Draining and Filling Cooling System.
2. Disconnect the inlet hose from the thermostat housing using the J 38185.
3. Disconnect the inlet hose from the radiator using the J 38185.
4. Remove the inlet hose.

Installation Procedure

1. Install the inlet hose in position and align the marks on the hose.
2. Connect the inlet hose to the radiator using the J 38185.
3. Connect the inlet hose to the thermostat housing using the J 38185.

Important: To properly fill the system you must use of the air bleed vents. Refer to Draining and Filling Cooling System.

4. Refill the coolant. Refer to Draining and Filling Cooling System.


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 1
Chevrolet Venture V6-3.4L VIN E 231
Radiator Hose: Service and Repair
Radiator Hose Replacement - Outlet
Removal Procedure

^ Tools Required
- J 38185 Hose Clamp Pliers

1. Drain the coolant. Refer to Draining and Filling Cooling System.


2. Disconnect the outlet hose from the water pump housing using the J 38185.
3. Disconnect the outlet hose from the radiator using the J 38185.
4. Remove the outlet hose.

Installation Procedure

1. Install the outlet hose in position and align the marks on the hose.
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 2
Chevrolet Venture V6-3.4L VIN E 232
2. Connect the outlet hose to the radiator using the J 38185.
3. Connect the outlet hose to the water pump housing using the J 38185.

Important: To properly fill the system you must use of the air bleed vents. Refer to Draining and Filling Cooling System.

4. Refill the coolant. Refer to Draining and Filling Cooling System.


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 1
Chevrolet Venture V6-3.4L VIN E 233
Coolant Level Indicator Module: Service and Repair
Removal Procedure

1. Drain the coolant until the coolant level is below the low coolant level module. Refer to Draining and Filling Cooling System.
2. Remove the low coolant module electrical connector.

3. Lift one leg of the retainer and pull outward with a twisting motion in order to remove the low coolant module.
4. Ensure that the coolant level module seal is not damaged.

Installation Procedure

1. Lubricate the coolant level module seal with coolant.

Important: Ensure that the retainer is installed correctly on the low coolant module.

2. Install the low coolant module.


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 2
Chevrolet Venture V6-3.4L VIN E 234

3. Install the low coolant module electrical connector.


4. Fill the cooling system. Refer to Draining and Filling Cooling System.
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 1
Chevrolet Venture V6-3.4L VIN E 235
Thermostat: Service and Repair
Removal Procedure

1. Remove the air cleaner and duct assembly. Refer to Air Filter Element Replacement in Computers and Controls.
2. Drain the coolant until the coolant level is below the thermostat. Refer to Draining and Filling Cooling System.
3. Remove the radiator hose from the thermostat housing. Refer to Radiator Hose Replacement - Inlet.
4. Remove the thermostat housing bolts and clean any sealer from the bolt threads.
5. Remove the thermostat housing and gasket.

6. Remove the thermostat.


7. Clean the mating surfaces.

Installation Procedure

1. Install the thermostat.


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 2
Chevrolet Venture V6-3.4L VIN E 236

2. Install the thermostat housing and gasket.


3. Install RTV sealer (GM P/N 1052366 or the equivalent) to the thermostat housing bolt threads.

Notice: Refer to Fastener Notice in Service Precautions.

4. Install the thermostat housing bolts.


^ Tighten the bolts to 25 Nm (18 ft. lbs.).
5. Install the radiator hose to the thermostat housing. Refer to Radiator Hose Replacement - Inlet.
6. Install the air cleaner and duct assembly. Refer to Air Filter Element Replacement in Computers and Controls.
7. Fill the cooling system. Refer to Draining and Filling Cooling System.
8. Inspect the cooling system for leaks. Repair as necessary.
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 1
Chevrolet Venture V6-3.4L VIN E 237
Exhaust System: Description and Operation
The exhaust system is used to carry the gases that are created by the engine. When the engine exhaust valve opens hot gases created by the engine
combustion cycle are allowed to travel out through the cylinder head into the exhaust manifold. In the exhaust manifold the exhaust gases combine
with exhaust gases from the other cylinders and pass the through a flanged port into the exhaust resonator pipe. The resonator and the muffler are
used to reduce the noise levels of the exhaust. The exhaust system exits at the rear of the vehicle to reduce exhaust noise and fumes from entry in to
the vehicle. Exhaust system hangers and insulators support the weight of the exhaust system, isolate engine noise, isolate engine vibration, space
the system away from the underbody of the vehicle and allow for exhaust system expansion that occurs as the exhaust system warms up.
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 1
Chevrolet Venture V6-3.4L VIN E 238
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 1
Chevrolet Venture V6-3.4L VIN E 239
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 1
Chevrolet Venture V6-3.4L VIN E 240
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 1
Chevrolet Venture V6-3.4L VIN E 241
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 1
Chevrolet Venture V6-3.4L VIN E 242
Catalytic Converter: Description and Operation
To control emissions of Hydrocarbons (HC), Carbon Monoxide (CO), and Oxides Of Nitrogen (NOx), a 3-way catalytic converter is used. The
catalyst within the converter promotes a chemical reaction which oxidizes the HC and CO present in the exhaust gas, converting the HG and GO
into harmless water vapor and carbon dioxide. The catalyst also reduces NOx, converting the NOx to nitrogen. The PCM has the ability to monitor
this process using the HO2S 1 and the HO2S 2 heated oxygen sensors. The HO2S 1 sensor produces an output signal which indicates the amount of
oxygen present in the exhaust gas entering the 3-way catalytic converter. The HO2S 2 sensor produces an output signal which indicates the oxygen
storage capacity of the catalyst. This in turn indicates the catalyst's ability to convert exhaust gases efficiently. If the catalyst is operating efficiently,
the HO2S 1 signal is far more active than that produced by the HO2S 2 sensor.

The catalyst monitor sensors operate the same as the fuel control sensors. Although the HO2S 2 sensor's main function is catalyst monitoring, the
sensor also plays a limited role in fuel control. If the sensor output indicates a voltage either above or below the 450 millivolt bias voltage for an
extended period of time, the PCM makes a slight adjustment to fuel trim to ensure that fuel delivery is correct for catalyst monitoring.

A problem with the HO2S 2 signal circuit should set DTC P0137 HO2S Circuit Low Voltage Sensor 2, DTC P0138 HO2S Circuit High Voltage
Sensor 2, or DTC P0140 HO2S Circuit Insufficient Activity Sensor 2, depending on the specific condition.

A fault in the heated oxygen sensor heater element or its ignition feed or ground results in slower oxygen sensor response. This may cause
erroneous catalyst monitor diagnostic results. A fault in the HO2S 2 heater circuit should cause DTC P0141 HO2S Heater Performance Sensor2 to
set.
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 1
Chevrolet Venture V6-3.4L VIN E 243
Catalytic Converter: Service and Repair
Catalytic Converter Replacement
Removal Procedure

Replace the entire converter assembly in order to properly service the three way catalytic converter.

1. Raise and suitably support the vehicle. Refer to Vehicle Lifting.


2. Remove the exhaust manifold pipe nuts from the exhaust manifold pipe studs.

3. Remove the catalytic converter nuts from the exhaust pipe.


4. Remove the three-way catalytic converter.

Installation Procedure

Notice: To prevent internal damage to the flexible coupling of the catalytic converter assembly, the converter must be supported. The
vertical movement at the rear of the catalytic converter assembly must not exceed 6 degrees up or down.

1. Install a new catalytic converter gasket.


2. Install a new exhaust manifold pipe gasket.
3. Position and support the new three-way catalytic converter under the vehicle.
4. Install the exhaust pipe to the three-way catalytic converter with the catalytic converter nuts. Do no tighten the nuts.
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 2
Chevrolet Venture V6-3.4L VIN E 244

Notice: Refer to Fastener Notice in Service Precautions.

5. Install the exhaust manifold pipe nuts to the exhaust manifold pipe studs.
^ Tighten the exhaust manifold pipe nuts to the exhaust manifold pipe stud to 35 Nm (26 ft. lbs.).
^ Tighten the catalytic converter nuts to the 34 Nm (25 ft. lbs.).
6. Lower the vehicle.
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 1
Chevrolet Venture V6-3.4L VIN E 245
Catalytic Converter: Service and Repair
Converter Hanger Assembly Replacement
Removal Procedure

1. Raise and suitably support the vehicle. Refer to Vehicle Lifting.


2. Remove the catalytic converter hanger insulators from the catalytic converter.
3. Remove the catalytic converter hanger bolts.
4. Remove the catalytic converter hanger.

Installation Procedure

1. Install the catalytic converter hanger.

Notice: Refer to Fastener Notice in Service Precautions.

2. Install the catalytic converter hanger bolts.


^ Tighten the catalytic converter hanger bolts to 35 Nm (26 ft. lbs.).
3. Install the catalytic converter hanger insulators to the catalytic converter.
4. Lower the vehicle.
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 1
Chevrolet Venture V6-3.4L VIN E 246
Exhaust Crossover Pipe: Service and Repair
Exhaust Crossover Replacement
Removal Procedure

1. Remove the throttle body air inlet duct. Refer to Air Filter Element Replacement in Computers and Controls.
2. Drain the engine coolant from the cooling system. Refer to Draining and Filling Cooling System in Cooling System.
3. Remove the inlet radiator hose from the engine. Refer to Radiator Hose Replacement - Inlet in Cooling System.
4. Remove the thermostat bypass pipe. Refer to Thermostat Bypass Pipes Replacement in Cooling System.
5. Remove the exhaust crossover pipe heat shield bolts.
6. Remove the exhaust crossover pipe heat shield.

7. Remove the exhaust crossover pipe nuts.


8. Remove the exhaust crossover pipe.

Installation Procedure

1. Install the exhaust crossover pipe.

Notice: Refer to Fastener Notice in Service Precautions.


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 2
Chevrolet Venture V6-3.4L VIN E 247

2. Install the exhaust crossover pipe nuts.


^ Tighten the exhaust crossover pipe nuts to 25 Nm (18 ft. lbs.).

3. Install the exhaust crossover pipe heat shield.


4. Install the exhaust crossover pipe heat shield bolts.
^ Tighten the exhaust crossover pipe heat shield bolts to 10 Nm (89 inch lbs.).
5. Install the thermostat bypass pipe. Refer to Thermostat Bypass Pipes Replacement in Cooling System.
6. Install the inlet radiator hose to the engine. Refer to Radiator Hose Replacement - Inlet in Cooling System.
7. Fill the cooling system with engine coolant. Refer to Draining and Filling Cooling System in Cooling System.
8. Install the throttle body air inlet duct. Refer to Air Filter Element Replacement in Computers and Controls.
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 1
Chevrolet Venture V6-3.4L VIN E 248
Exhaust Crossover Pipe: Service and Repair
Exhaust Crossover Pipe Replacement
Removal Procedure

1. Disconnect the battery ground (negative) cable. Refer to Battery Negative Cable Disconnect/Connect Procedure.
2. Remove the throttle body air inlet duct.
3. Drain the coolant from the cooling system. Refer to Draining and Filling Cooling System in Cooling System.
4. Remove the inlet radiator hose from the engine. Refer to Radiator Hose Replacement - Inlet in Cooling System.
5. Remove the thermostat bypass pipe. Refer to Thermostat Bypass Pipes Replacement in Cooling System.
6. Remove the exhaust crossover heat shield bolts.
7. Remove the exhaust crossover heat shield.

8. Remove the exhaust crossover pipe studs/nuts.


9. Remove the exhaust crossover pipe.

Installation Procedure

1. Install the exhaust crossover pipe.


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 2
Chevrolet Venture V6-3.4L VIN E 249

Notice: Refer to Fastener Notice in Service Precautions.

2. Install the exhaust crossover pipe studs/nuts.


^ Tighten the exhaust crossover pipe studs/nuts to 25 Nm (18 ft. lbs.).

3. Install the exhaust crossover heat shield.


4. Install the exhaust crossover heat shield bolts.
^ Tighten the exhaust crossover heat shield bolts to 10 Nm (89 inch lbs.).
5. Install the thermostat bypass pipe. Refer to Thermostat Bypass Pipes Replacement in Cooling System.
6. Install the inlet radiator hose to the engine. Refer to Radiator Hose Replacement - Inlet in Cooling System.
7. Fill the cooling system with engine coolant. Refer to Draining and Filling Cooling System in Cooling System.
8. Install the throttle body air inlet duct.
9. Connect the battery ground (negative) cable. Refer to Battery Negative Cable Disconnect/Connect Procedure.
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 1
Chevrolet Venture V6-3.4L VIN E 250
Exhaust Manifold: Service and Repair
Exhaust Manifold Replacement (Engine Left Side)
Removal Procedure

1. Remove the throttle body air inlet duct. Refer to Air Filter Element Replacement in Computers and Controls.
2. Drain the engine coolant from the cooling system. Refer to Draining and Filling Cooling System in Cooling System.
3. Remove the right engine mount strut bracket. Refer to Engine Mount Strut Bracket Replacement (Radiator Upper Support) or Engine Mount
Strut Bracket Replacement (Left Side) or Engine Mount Strut Bracket Replacement (Right Side).
4. Disconnect the inlet radiator hose from the engine. Refer to Radiator Hose Replacement - Inlet in Cooling System.
5. Remove the thermostat bypass pipe. Refer to Thermostat Bypass Pipes Replacement in Cooling System.
6. Remove the exhaust crossover pipe bolts from the engine left side exhaust manifold. Refer to Exhaust Crossover Removal.
7. Remove the exhaust manifold heat shield bolts.
8. Remove the exhaust manifold heat shield.

9. Remove the exhaust manifold nuts.


10. Remove the exhaust manifold.
11. Remove the exhaust manifold gasket.
12. Clean the engine left side exhaust manifold to the engine left side cylinder head sealing surfaces. Refer to Exhaust Manifold Clean and
Inspect.

Installation Procedure
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 2
Chevrolet Venture V6-3.4L VIN E 251

1. Install the exhaust manifold gasket.


2. Install the exhaust manifold.

Notice: Refer to Fastener Notice in Service Precautions.

3. Install the exhaust manifold nuts.


^ Tighten the exhaust manifold nuts to 16 Nm (12 ft. lbs.).

4. Install the exhaust manifold heat shield.


5. Install the exhaust manifold heat shield bolts.
^ Tighten the exhaust manifold heat shield bolts to 10 Nm (89 inch lbs.).
6. Install the exhaust crossover pipe. Refer to Exhaust Crossover Installation.
7. Install the thermostat bypass pipe. Refer to Thermostat Bypass Pipes Replacement in Cooling System.
8. Connect the inlet radiator hose to the engine. Refer to Radiator Hose Replacement - Inlet in Cooling System.
9. Install the right engine mount strut bracket. Refer to Engine Mount Strut Bracket Replacement (Radiator Upper Support) or Engine Mount
Strut Bracket Replacement (Left Side) or Engine Mount Strut Bracket Replacement (Right Side).
10. Fill the cooling system with engine coolant. Refer to Draining and Filling Cooling System in Cooling System.
11. Install the throttle body air inlet duct. Refer to Air Filter Element Replacement in Computers and Controls.
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 1
Chevrolet Venture V6-3.4L VIN E 252
Exhaust Manifold: Service and Repair
Exhaust Manifold Replacement (Engine Right Side)
Removal Procedure

1. Remove the windshield wiper motor cover. Refer to Wiper Module Cover Replacement in Wiper and Washer Systems.
2. Remove the throttle body air inlet duct. Refer to Air Filter Element Replacement in Computers and Controls.
3. Remove the accelerator cable bracket from the throttle body. Refer to Accelerator Controls Cable Replacement in Computers and Controls.
4. Remove the manifold air pressure (MAP) sensor. Refer to MAP Sensor Replacement in Computers and Controls.
5. Remove the exhaust gas recirculation (EGR) valve. Refer to EGR Valve Replacement in Computers and Controls.
6. Rotate the engine for service access. Refer to Rotating the Engine for Service Access.
7. Remove the ignition module and the ignition coils with the bracket.
8. Remove the spark plug wires from the engine right bank spark plugs.
9. Disconnect the oxygen sensor electrical connector.
10. Remove the evaporative emissions (EVAP) solenoid bracket.
11. Remove the exhaust crossover pipe nuts/studs from the engine right bank exhaust manifold. Refer to Exhaust Crossover Removal.
12. Raise and support the vehicle. Refer to Vehicle Lifting.
13. Remove the catalytic converter. Refer to Catalytic Converter Replacement in Powertrain Management.
14. Remove the exhaust manifold heat shield bolts.
15. Remove the exhaust manifold heat shields.

16. Remove the exhaust manifold nuts.


17. Remove the exhaust manifold.
18. Remove the exhaust manifold gasket.
19. Lower the vehicle.
20. Clean the engine right side exhaust manifold sealing surfaces and the cylinder head sealing surfaces. Refer to Exhaust Manifold Clean and
Inspect.
21. If you are REPLACING the engine right side exhaust manifold, remove the Exhaust Gas Recirculation (EGR) valve pipe.
22. If you are REPLACING the engine right side exhaust manifold, remove the Heated Oxygen Sensor (H02S). Refer to Heated Oxygen Sensor
(HO2S) Replacement (HO2S1) or Heated Oxygen Sensor (HO2S) Replacement (HO2S2) in Computers and Controls.

Installation Procedure
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 2
Chevrolet Venture V6-3.4L VIN E 253

1. If removed, install the Heated Oxygen Sensor (HO2S). Refer to Heated Oxygen Sensor (H02S) Replacement (HO2S1) or Heated Oxygen
Sensor (HO2S) Replacement (H02S2) in Computers and Controls.
2. If removed, install the exhaust gas recirculation (EGR) valve pipe.
3. Raise and support the vehicle. Refer to Vehicle Lifting.
4. Install the exhaust manifold gasket.
5. Install the exhaust manifold.

Notice: Refer to Fastener Notice in Service Precautions.

6. Install the exhaust manifold nuts.


^ Tighten the exhaust manifold nuts to 16 Nm (12 ft. lbs.).

7. Install the exhaust manifold lower heat shield.


8. Install the exhaust manifold upper heat shield.
9. Install the exhaust manifold heat shield bolts.
^ Tighten the exhaust manifold heat shield bolts to 10 Nm (89 inch lbs.).
10. Install the catalytic converter. Refer to Catalytic Converter Replacement in Powertrain Management.
11. Lower the vehicle.
12. Install the exhaust crossover pipe nuts/studs to the engine right side exhaust manifold. Refer to Exhaust Crossover Installation.
13. Install the exhaust crossover pipe heat shield. Refer to Exhaust Crossover Installation.
14. Lower the vehicle.
15. Connect the Heated Oxygen Sensor (H02S) electrical connector.
16. Install the EVAP solenoid bracket.
17. Install the spark plug wires to the engine right bank spark plugs.
18. Install the ignition module and the ignition coils with the bracket.
19. Rotate the engine back to the original position. Refer to Rotating the Engine for Service Access.
20. Install the EGR valve to the intake manifold. Refer to EGR Valve Replacement in Computers and Controls.
21. Install the MAP sensor. Refer to MAP Sensor Replacement in Computers and Controls.
22. Install the accelerator cable bracket to the throttle body. Refer to Accelerator Controls Cable Replacement in Computers and Controls.
23. Install the throttle body air inlet duct. Refer to Air Filter Element Replacement in Computers and Controls.
24. Install the windshield wiper motor cover. Refer to Wiper Module Cover Replacement in Wiper and Washer Systems.
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 1
Chevrolet Venture V6-3.4L VIN E 254
Exhaust Pipe/Muffler Hanger: Service and Repair
Removal Procedure

1. Raise and suitably support the vehicle. Refer to Vehicle Lifting.


2. Remove the muffler hanger insulators from the muffler.
3. Remove the muffler hanger bolts.
4. Remove the muffler hanger.

Installation Procedure

1. Install the muffler hanger.

Notice: Refer to Fastener Notice in Service Precautions.

2. Install the muffler hanger bolts.


^ Tighten the muffler hanger bolts to 35 Nm (26 ft. lbs.).
3. Install the muffler hanger insulators to the muffler.
4. Lower the vehicle.
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 1
Chevrolet Venture V6-3.4L VIN E 255
Heat Shield: Service and Repair
Converter Heat Shield Replacement
Removal Procedure

1. Raise and support the vehicle. Refer to Vehicle Lifting.


2. Remove the catalytic converter. Refer to Catalytic Converter Replacement.
3. Use a drill to remove the catalytic converter heat shield rivets.
4. Remove the catalytic converter heat shield.

Installation Procedure

1. Install the catalytic converter heat shield.


2. Install the catalytic converter heat shield to the vehicle with new rivets.
3. Install the catalytic converter. Refer to Catalytic Converter Replacement.
4. Lower the vehicle.
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 1
Chevrolet Venture V6-3.4L VIN E 256
Heat Shield: Service and Repair
Exhaust Heat Shield Replacement
Removal Procedure

1. Raise and support the vehicle. Refer to Vehicle Lifting.


2. Remove the exhaust system muffler. Refer to Muffler Replacement
3. Use a drill in order to remove the rivets at the exhaust muffler heat shield.
4. Remove the exhaust muffler heat shield from the vehicle.

Installation Procedure

1. Install the exhaust muffler heat shield to the vehicle with new rivets.
2. Install the exhaust system muffler. Refer to Muffler Replacement.
3. Lower the vehicle.
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 1
Chevrolet Venture V6-3.4L VIN E 257
Muffler: Service and Repair
Removal Procedure

The muffler is serviced as one piece from the catalytic converter to the tail pipe.

1. Raise and support the vehicle. Refer to Vehicle Lifting.

Notice: To prevent internal damage to the flexible coupling of the catalytic converter assembly, the converter must be supported. The
vertical movement at the rear of the catalytic converter assembly must not exceed 6 degrees up or down.

2. Use a utility stand in order to support the catalytic converter.


3. Remove the rear axle tie rod. Refer to Tie Rod Replacement in Steering and Suspension.
4. Lower the support and the tie rod.
5. Remove the catalytic converter nuts.
6. Remove the catalytic converter gasket.

7. Remove the exhaust hanger insulators from the exhaust pipes.


8. Remove the muffler and exhaust pipes towards the front of the vehicle and over the rear axle.
9. Clean the catalytic converter flange and the muffler flange.

Installation Procedure
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 2
Chevrolet Venture V6-3.4L VIN E 258

1. Install the muffler and exhaust pipes over the rear axle and towards the rear of the vehicle.
2. Install the exhaust hanger insulators to the exhaust pipes.
3. Install the rear axle tie rod. Refer to Tie Rod Replacement in Steering and Suspension.

4. Install a new catalytic converter gasket.

Notice: Refer to Fastener Notice in Service Precautions.

5. Install the catalytic converter nuts.


^ Tighten the catalytic converter nuts to 34 Nm (25 ft. lbs.).
6. Lower the vehicle.
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 1
Chevrolet Venture V6-3.4L VIN E 259
Ignition System: Description and Operation

Camshaft Position (CMP) Sensor

The Camshaft Position (CMP) sensor is located on the timing cover behind the water pump near the camshaft sprocket. As the camshaft sprocket
turns, a magnet in the sprocket activates the Hall-effect switch in the CMP sensor. When the Hall-effect switch is activated, the signal line to the
PCM is grounded, pulling the CMP sensor signal circuits applied voltage low. This is interpreted as a CAM signal.

The CAM signal is created as piston #1 is on the intake stroke. If the correct CAM signal is not received by the PCM, DTC P0341 will be set.
Circuits Affecting Ignition Control
In order to properly control ignition timing, the PCM relies on the following information:
^ Engine load (manifold pressure or vacuum)
^ Atmospheric (barometric) pressure
^ Engine temperature
^ Intake air temperature
^ Crankshaft position
^ Engine speed (RPM)

The IC system consists of the following components:


^ Ignition coils
^ IC module
^ 7X CKP sensor
^ 24X CKP sensor
^ PCM
^ All connecting wires

The electronic IC module connector terminals are identified as shown in the Electronic Ignition System graphic. These circuits perform the
following functions:
^ 3X reference high-The 7X crankshaft position sensor sends a signal to the electronic ignition control module which generates a reference
pulse that is sent to the PCM. The PCM uses this signal to calculate crankshaft position and engine speed (also used to trigger the fuel
injectors).
^ 3X reference low-This wire is grounded through the ICM and assures the ground circuit has no voltage drop between the ICM and the PCM.
^ Ignition control bypass-During initial cranking, the PCM will look for synchronizing pulses from the camshaft position sensor and the 7X
crankshaft position sensor. The pulses indicate the position of the #1 piston and the #1 intake valve. Five volts is applied to the bypass circuit
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 2
Chevrolet Venture V6-3.4L VIN E 260
at precisely the same time these signals are received by the PCM. This generally occurs within one or two revolutions of the crankshaft. An
open or grounded bypass circuit will set a DTC P1351 and the engine will run at base ignition timing. A small amount of spark advance is
built into the ignition control module to enhance performance.
^ Ignition Control (IC)-The PCM uses this circuit to trigger the electronic ignition control module. The PCM uses the crankshaft reference
signal to calculate the amount of spark advance needed.
^ 24X reference signal-The 24X crankshaft position sensor increases idle quality and low speed driveability by providing better resolution at a
calibrated RPM.
Electronic Ignition (EI) System
The Electronic Ignition (EI) system on the 3400 LA1 (VIN E) engine uses a coil pack with one ignition coil for each two cylinders in the engine.
Mounted under the ignition coils on each system is an Ignition Control Module (ICM) that performs ignition coil switching functions and interacts
with the Powertrain Control Module (PCM) to optimize ignition system operation. On these engine systems, the spark timing is controlled
electronically.

The ICM controls the spark timing during engine start-up, and provides a back-up timing system that will allow the engine to run in the event of an
open or ground in the Ignition Control (IC) circuit. Once the engine starts and is running above an approximate engine speed of 400 RPM, the
PCM takes over the spark timing and sends signals to the ICM for ignition coil switching. The electronic ignition systems used on these engines use
a waste spark method of spark distribution.

Each cylinder is paired with its opposing cylinder in the firing order, so that one cylinder on compression fires simultaneously with the opposing
cylinder on exhaust. The spark that occurs in the cylinder that is on the exhaust stroke is referred to as the waste spark. The spark plugs in the two
opposing cylinders are connected to the two secondary terminals of the same ignition coil. The spark voltage appears at the center electrode of one
of the spark plugs and jumps to the side electrode, then passes through the engine to the other spark plug. At the second spark plug, the spark jumps
from the side electrode to the center electrode and completes the series circuit back to the ignition coil.

The high level of energy available from the ignition coil is more than sufficient to fire both plugs simultaneously. Since the waste spark requires
very little of the available voltage to fire, most of the coil output voltage is available to fire the cylinder that is on the compression stroke. Engine
speed (RPM) and cylinder position in the intake-compression-power-exhaust sequence are sensed electronically and are used by the ICM and PCM
to control timing. These parameters are provided by a magnetic Crankshaft Position (CKP) sensor mounted in the engine block. The magnetic CKP
sensor consists of a wire coil wound around a permanent magnet. The sensor is positioned near a reluctor ring on the crankshaft. The reluctor ring
has notches which trigger signals in the magnetic sensor to indicate Crankshaft Position (CKP) and crankshaft speed (RPM). These signals are used
by the ICM during start up, then passed on to the PCM to help determine optimum timing while the engine is running. The PCM also uses other
inputs separate from the ignition system itself, to determine optimum timing.

For a description of the RPO Code(s) shown in this article/images refer to the RPO Code List found at Vehicle/Application ID See: Application and
ID
General Description
The electronic ignition system controls fuel combustion by providing a spark to ignite the compressed air/fuel mixture at the correct time. To
provide optimum engine performance, fuel economy, and control of exhaust emissions, the PCM controls the spark advance of the ignition system.

Electronic ignition has the following advantages over a mechanical distributor system:
^ No moving parts
^ Less maintenance
^ Remote mounting capability
^ No mechanical load on the engine
^ More coil cool down time between firing events
^ Elimination of mechanical timing adjustments
^ Increased available ignition coil saturation time

The electronic ignition system does not use the conventional distributor and coil. The ignition system consists of three ignition coils, an ignition
control module, a Camshaft Position (CMP) sensor, 7X Crankshaft Position (CKP) sensor in the block, a 24X CKP sensor behind the crankshaft
balancer, related connecting wires, and the Ignition Control (IC) and fuel metering portion of the PCM.

Conventional ignition coils have one end of the secondary winding connected to the engine ground. In this ignition system, neither end of the
secondary winding is grounded. Instead, each end of a coil's secondary winding is attached to a spark plug. Each cylinder is paired with the cylinder
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 3
Chevrolet Venture V6-3.4L VIN E 261
that is on the opposite side (1 and 4, 2 and 5, 3 and 6). These two plugs are on companion cylinders, i.e., on top dead center at the same time.

When the coil discharges, both plugs fire at the same time to complete the series circuit. The cylinder on compression is said to be the event
cylinder and the one on exhaust is the waste cylinder. The cylinder on the exhaust stroke requires very little of the available energy to fire the spark
plug. The remaining energy will be used as required by the cylinder on the compression stroke. The same process is repeated when the cylinders
reverse roles. This method of ignition is called a waste spark ignition system.

Since the polarity of the ignition coil primary and secondary windings is fixed, one spark plug always fires with normal polarity and the companion
plug fires with reverse polarity. This differs from a conventional ignition system that fires all the plugs with the same polarity. Because the ignition
coil requires approximately 30 percent more voltage to fire a spark plug with reverse polarity, the ignition coil design is improved, with saturation
time and primary current flow increased. This redesign of the system allows higher secondary voltage to be available from the ignition coils-more
than 40 kilovolts (40,000 volts) at any engine RPM. The voltage required by each spark plug is determined by the polarity and the cylinder
pressure. The cylinder on compression requires more voltage to fire the spark plug than the one on exhaust.

One spark plug may fire even though a plug wire from the same coil may be disconnected from the companion plug. The disconnected plug wire
acts as one plate of a capacitor, with the engine being the other plate. These two capacitor plates are charged as a spark jumps across the gap of the
connected spark plug. The plates are then discharged as the secondary energy is dissipated in an oscillating current across the gap of the spark plug
that is still connected. Secondary voltage requirements are very high with an open spark plug or spark plug wire. The ignition coil has enough
reserve energy to fire the plug that is still connected at idle, but the coil may not fire the spark plug under high engine load. A more noticeable
misfire may be evident under load, both spark plugs may then be misfiring.
Ignition Coils
Three twin-tower ignition coils are individually mounted to the ignition control module. Each coil provides spark for two plugs simultaneously
(waste spark distribution). Each coil is serviced separately. Two terminals connect each coil pack to the module. Each coil is provided a fused
ignition feed. The other terminal at each coil is individually connected to the module, which will energize one coil at a time by completing and
interrupting the primary circuit ground path to each coil at the proper time.
Ignition Control (IC) Module

The Ignition Control (IC) module performs the following functions:


^ Determines the correct ignition coil firing sequence, based on 7X pulses-This coil sequencing occurs at start-up. After the engine is running,
the module determines the sequence, and continues triggering the ignition coils in proper sequence.
^ Sends the 3X crankshaft reference (fuel control) signal to the PCM-The PCM determines engine RPM from this signal. This signal is also
used by the PCM to determine crankshaft speed for Ignition Control (IC) spark advance calculations.

The 3X reference signal sent to the PCM by the IC module is an on, off pulse occurring 3 times per crankshaft revolution.
Ignition Switch
The mechanical key and lock cylinder switch is located in the steering column on the right-hand side, just below the steering wheel. The electrical
switching portion of the assembly is separate from the key and lock cylinder.
Ignition System
There are important considerations to point out when servicing the ignition system. The following Noteworthy Information will list some of these,
to help the technician in servicing the ignition system.
^ The ignition coils secondary voltage output capabilities are very high - more than 40,000 volts. Avoid body contact with ignition high
voltage secondary components when the engine is running, or personal injury may result.
^ The 7X crankshaft position sensor is the most critical part of the ignition system. If the sensor is damaged so that pulses are not generated, the
engine will not start.
^ Crankshaft position sensor clearance is very important! The sensor must not contact the rotating interrupter ring at any time, or sensor
damage will result. If the balancer interrupter ring is bent, the interrupter ring blades will destroy the sensor.
^ Ignition timing is not adjustable. There are no timing marks on the crankshaft balancer or timing chain cover.
^ If crankshaft position sensor replacement is necessary, the crankshaft balancer must be removed first. The balancer is a press fit onto the
crankshaft. Removing the serpentine accessory drive belt and balancer attaching bolt will allow removal with the special tool J 38197
Balancer Remover. When reinstalled, proper torquing of the balancer attachment bolt is critical to ensure the balancer stays attached to the
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 4
Chevrolet Venture V6-3.4L VIN E 262
crankshaft.
^ If a crankshaft position sensor assembly is replaced, inspect the crankshaft balancer interrupter ring for any blades being bent. If this is not
inspected closely and a bent blade exists, the new crankshaft position sensor can be destroyed by the bent blade with only one crankshaft
revolution.
^ Neither side of the ignition coil primary or secondary windings is connected to engine ground. Although the ignition coil packs are secured to
the IC module, there is not an electrical connection to ground.
^ Be careful not to damage the secondary ignition wires or boots when servicing the ignition system. Rotate each boot to dislodge the boot
from the plug or coil tower before pulling the boot from either a spark plug or the ignition coil. Never pierce a secondary ignition wire or
boot for any testing purposes! Future problems are guaranteed if pinpoints or test lights are pushed through the insulation for testing.
^ The IC module is grounded to the engine block through 3 mounting studs used to secure the module to the mounting bracket. If servicing is
required, ensure that good electrical contact is made between the module and the mounting bracket, including proper hardware and torque.
^ A conventional tachometer used to check RPM on a primary ignition tach lead will not work on this ignition system. In order to check RPM,
use a Scan Tool.
Modes of Operation
Ignition Control (IC) spark timing is the PCMs method of controlling spark advance and ignition dwell when the ignition system is operating in the
IC Mode. There are two modes of ignition system operation:
^ Bypass Mode
^ IC Mode

In Bypass Mode, the ignition system operates independently of the PCM, with Bypass Mode spark advance always at 10 (BTDC). The PCM has no
control of the ignition system when in this mode. In fact, the PCM could be disconnected from the vehicle and the ignition system would still fire
the spark plugs, as long as the other ignition system components were functioning. (This would provide spark but no fuel injector pulses. The
engine will not start in this situation.) The PCM switches to IC Mode (PCM controlled spark advance) as soon as the engine begins cranking. After
the switch is made to IC Mode, the IC Mode will stay in effect until one of the following conditions occur:
^ The engine is turned off.
^ The engine quits running.
^ A PCM/IC module fault (DTC P1351, P1352, P1361, or P1362) is detected.

If a PCM/IC module fault is detected while the engine is running, the ignition system will switch to Bypass Mode operation. The engine may quit
running, but will restart and stay in Bypass Mode with a noticeable loss of performance.

In the IC Mode, the ignition spark timing and ignition dwell time is fully controlled by the PCM. IC spark advance and ignition dwell is calculated
by the PCM using the following inputs:
^ Engine speed (24X reference or 3X reference)
^ Crankshaft position (24X reference or 3X reference and Camshaft position PCM input signal)
^ Engine Coolant Temperature (ECT) sensor
^ Throttle Position (TP) sensor
^ Knock Signal (Knock Sensor)
^ Park/Neutral Position (PRNDL input)
^ Vehicle Speed (Vehicle Speed Sensor)
^ PCM and ignition system supply voltage

The following describes the PCM to ignition control module circuits:


^ 3X reference PCM input-The Ignition Control Module Generates the 3X reference signal from the 7X CKP Sensor. The IC module sends the
3X reference signal to the PCM. The PCM uses this signal to calculate engine RPM and crankshaft position at speeds above 1600 RPM. If
the PCM receives no pulses on this circuit, the PCM will use the 24X reference pulses to calculate RPM and crankshaft position. The engine
will continue to run and start normally as long as 7X CKP Sensor pulses are being received, but DTC P1374 will be set.
^ 24X reference PCM input-The 24X CKP Sensor generates the 24X reference signal to calculate engine speed and crankshaft position at
engine speeds below 1600 RPM. The 24X reference signal provides better resolution within the calibrated RPM range. This increases idle
quality and low speed driveability. When engine speed exceeds 1600 RPM, the PCM begins using the, 3X reference signal to control spark
timing. If the 24X reference signal is not received by the PCM while the engine is running, a DTC P0336 will be set and 3X reference will be
used to control spark advance under 1600 RPM, and Bypass Mode will be in effect under 400 RPM. The engine will continue to run and
start normally.
^ Reference low PCM input-The reference low circuit establishes a common ground between the ignition control module and the PCM. The
wire is connected to engine ground only through the ignition control module. The circuit minimizes electrical ground differences between the
PCM and the IC module. The PCM uses the reference low circuit to clearly recognize the 3X reference signals. If the circuit is open, or
connected to ground at the PCM, the circuit may cause poor engine performance and possibly a MIL (Service Engine Soon) without a DTC.
^ Knock Sensor (KS) PCM input-The PCM contains integrated knock sensor diagnostic circuitry. The KS system is comprised of the knock
sensor, PCM, and related wiring. The PCM monitors the knock sensor signal to detect engine detonation. When spark knock occurs, the
PCM retards the spark timing (IC) to reduce detonation. Retarded spark timing may also be the result of excessive engine mechanical or
transaxle noise. If a KS signal is found varying within the average voltage a DTC P0327 may set.
^ Bypass signal PCM output-The IC module controls spark timing until the PCM detects a calibrated number of 3X reference pulses (Bypass
Mode). When the PCM receives these pulses, the PCM then provides 5.0 volts to the IC module on the Bypass Circuit. This signals the IC
module to transfer spark timing control the PCM (IC Mode). Proper sequencing of the 3 ignition coils, i.e. which coil to fire, is always the job
of the ignition control module. If the PCM detects a short to voltage on the Bypass circuit DTC P1362 will set. An open in the Bypass Circuit
will set DTC P1352.
^ Ignition Control (IC) PCM output-The PCM sends out timing pulses to the IC module on the IC Circuit. When the ignition system is in the
Bypass mode (the PCM has not sent the 5.0 volt bypass signal), the IC module grounds these pulses. When the IC Mode (the PCM has
supplied the bypass signal), these pulses are sent to the IC module to control ignition spark timing. If the IC circuit is grounded when the
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 5
Chevrolet Venture V6-3.4L VIN E 263
engine is started, DTC P1361 will set and the ignition system will stay in the Bypass Mode. If the IC circuit becomes open or grounded
during IC Mode operation, DTC P1351 or P1361 may set. When this happens, the engine will quit running but will restart. Upon restart
following an ignition cycle, DTC P1361 will be set, and the ignition system will operate in Bypass Mode.
Powertrain Control Module (PCM)

Powertrain Control Module (PCM)

The PCM is responsible for maintaining proper spark and fuel injection timing for all driving conditions. To provide optimum driveability and
emissions, the PCM monitors input signals from the following components in calculating Ignition Control (IC) spark timing:
^ IC module
^ Engine Coolant Temperature (ECT) sensor
^ Intake Air Temperature (IAT) sensor
^ Mass Air Flow (MAF) sensor
^ Trans Range inputs from Transaxle Range switch
^ Throttle Position (TP) sensor
^ Vehicle Speed Sensor (VSS)

Secondary Ignition Wiring


The spark plug wiring used with ignition systems is a carbon impregnated cord conductor, encased in a 7 mm (9/32 in) or 8 mm (5/16 in) diameter
silicone rubber jacket. The silicone jacket withstands very high temperatures. Silicone spark plug boots form a tight seal on the plug. The boot
should be twisted 1/2 turn before removing. Care should also be used when connecting a timing light or other pick-up equipment. Do not force
anything between the boot and wiring, or through the silicone jacket. Connections should be made in parallel using an adapter. Do not pull on the
wire to remove. Pull on the boot, or use a tool designed for this purpose.
Spark Plugs

Extended Life Spark Plug (Typical)

Resistor type, tapered seat spark plugs are used on all engines. No gasket is used on these tapered seat plugs. When replacing spark plugs, use only
the type specified. Normal service is assumed to be a mixture of idling, slow speed, and high-speed driving. Occasional intermittent high-speed
driving is needed for good spark plug performance. Intermittent high-speed driving gives increased combustion heat, burning away carbon or
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 6
Chevrolet Venture V6-3.4L VIN E 264
oxides that have built up from frequent idling, or continual stop-and-go driving.

Spark plugs are protected by insulating boots made of special heat-resistant materials, which cover the spark plug terminal and extend downward
over a portion of the plug insulator. These boots prevent flash-over, which causes engine misfiring. Do not mistake corona discharge for flash-over,
or a shorted insulator. Corona is a steady blue light appearing around the insulator, just above the shell crimp. It is the visible evidence of a
high-tension field and has no effect on ignition performance. Usually it can be detected only in darkness. This discharge may repel dust particles,
leaving a clear ring on the insulator just above the shell. This ring is sometimes mistakenly regarded as evidence that combustion gases have blown
out between the shell and the insulator.
24X & 7X Crankshaft Position Sensors Interrupter Ring

The 24X crankshaft position (CKP) sensor (1), secured in a mounting bracket (3) and bolted to the front side of the engine timing chain cover (2),
is partially behind the crankshaft balancer.

The 7X CKP sensor uses a two wire connector at the sensor and a three-way connector at the ignition control module.

The 24X CKP sensor contains a Hall-effect switch. The magnet and Hall-effect switch are separated by an air gap. A Hall-effect switch reacts like a
solid stale switch, grounding a low current signal voltage when a magnetic field is present. When the magnetic field is shielded from the switch by
a piece of steel placed in the air gap between the magnet and the switch, the signal voltage is not grounded. If the piece of steel (called an
interrupter) is repeatedly moved in and out of the air gap, the signal voltage will appear to go on-off, on-off, on-off. Compared to a conventional
mechanical distributor, this on-off signal is similar to the signal that a set of breaker points in the distributor would generate as the distributor shaft
turned and the points opened and closed.
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 7
Chevrolet Venture V6-3.4L VIN E 265

In the case of the electronic ignition system, the piece of steel is a concentric interrupter ring mounted to the rear of the crankshaft balancer. The
interrupter ring has blades and windows that, with crankshaft rotation, either block the magnetic field or allow the field to reach the Hall-effect
switch. The Hall-effect switch is called a 24X CKP sensor, because the interrupter ring has 24 evenly spaced blades and windows. The 24X CKP
sensor produces 24 on-off pulses per crankshaft revolution.

The interrupter ring is a special wheel cast on the crankshaft that has seven machined slots, six of which are equally spaced 60 degrees apart. The
seventh slot is spaced 10 degrees from one of the other slots. As the interrupter ring rotates with the crankshaft, the slots change the magnetic field.
This will cause the 7X to ground the 3X signal voltage that is supplied by the ignition control module. The ignition control module interprets the
7X on-off signals as an indication of crankshaft position. The ignition control module must have the 7X signal to fire the correct ignition coil.

The 7X interrupter ring and Hall-effect switch react similarly. The 24X signal is used for better resolution at a calibrated RPM.
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 1
Chevrolet Venture V6-3.4L VIN E 266
Ignition System: Initial Inspection and Diagnostic Overview

Checking the Basics


DIAGNOSTIC NOTES
Diagnosing problems in modern automobiles can sometimes be very frustrating and confusing, especially when it involves computer controlled
systems. The fact is, for the most part automotive electronics have been proven quite reliable, and the greatest number of problems with new cars
are the same kinds of problems that older cars without computer controls have.

Before suspecting a computer problem, perform a careful visual inspection. Check under the hood for the same kinds of problems you would
look for on a non-computer controlled engine. These include fluid leaks, vacuum leaks, dirty filters, overheating, oil burning, poor connections
or loose wires, bad spark plug wires and/or spark plugs, restricted mufflers and exhaust systems, worn mechanical parts, exhaust leaks, and other
familiar kinds of problems. Be thorough! You may save a lot of time.

Begin all troubleshooting by Checking the Basics. Certain basic faults may be undetectable by the Powertrain Control Module (PCM)
self-diagnostic system and can actually interfere with self-checking and fault memory operation. Low battery voltage, for example, can cause
erroneous faults to set in PCM memory or can cause a system to go "Fail Safe" without setting a fault in memory. Because system fault memory
is cleared whenever PCM or battery are disconnected, fault codes should be read prior to any vehicle power interruption or troubleshooting. Prior
to any teardown, repair or component replacement, consider the following steps:

COMPLAINT VERIFICATION
Whenever possible, the technicians should personally verify the complaint. Having experienced the malfunction, technicians are less likely to
attempt repairing non-existent faults.

MALFUNCTION VERIFICATION
Sophisticated automotive systems are easily misunderstood. This can lead to repairs that attempt to force a system to perform as it was never
intended. The troubleshooting technician should compare actual system operation to nominal system operation as described in Description and
Operation. The technician is also encouraged to compare problem vehicle system operation with a known good vehicle.

PREVIOUS REPAIRS
Vehicle repair history can provide explanations to unusual complaints which seem to elude normal troubleshooting attempts. Incorrect
components or unapproved repairs can have subtle influences on seemingly unrelated systems.

BATTERY STATE OF CHARGE


Batteries in a state of partial discharge can have a dramatic effect on the PCM and related electrical components.

POSITIVE BATTERY CABLE INTEGRITY


All B+ connections must be in perfect condition for trouble-free electronic system operation.

FUSIBLE LINK INTEGRITY


Fusible links prevent possible damage to electrical components and wiring harnesses. These links and their connections must be without dynamic
resistance. Dynamic resistance can only be checked using the voltage drop method of testing.

NEGATIVE GROUND CONNECTIONS


All B- connections must be checked and verified to be in perfect condition. A poor "common" ground point will cause seemingly unrelated
systems to influence one another. High current systems which encounter a poor "common" ground can back feed through other electrical
systems, causing unusual operation and inexplicable component failure. Electrical system ground side should be checked dynamically using the
voltage drop technique.

POWERTRAIN CABLE ATTACHMENTS


Metal cables attached to engine or transmission which appear overheated and/or discolored indicate the need to thoroughly test all ground
connections.

POWER SUPPLY RELAYS


Fuel pump and main relays, as well as their plug connections, can be a source of intermittent operation which will not set a code in PCM fault
memory.

HIGH TENSION COIL AND SECONDARY COMPONENTS WIRING


Secondary ignition system should be checked visibly as well as with a suitable engine analyzer and scope. Check components for tight
connections and freedom from carbon tracking, moisture and corrosion.

FUEL DELIVERY AND FUEL RAIL PRESSURE


Fuel delivery must begin at once when cranking and pressure in the fuel rails must be within specifications. Fuel pressure must be maintained
between fuel pump outlet and pressure regulator after engine shutdown.

SPARK PLUG CLEARANCE


Spark plug gap, if out of specification, can significantly impair engine performance. Verify spark plug type, condition, and gap according to
specification.

VACUUM AND VAPOR HOSE INTEGRITY


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 2
Chevrolet Venture V6-3.4L VIN E 267
Vacuum and vapor hoses must be routed correctly and not leaking. Always use the underhood label for primary information.

AIR/FUEL RATIO
Adaptive engine management systems efficiently compensate for conditions which may affect the combustion process. However, when
troubleshooting idle quality or driveability complaints, it is still necessary to consider the following:
- Injector spray pattern quality
- Presence of unmetered air leaks
- Evaporative purge system
- Excessive engine oil dilution
- Substandard fuel or unapproved additives
- Carbon build-up

TESTING EQUIPMENT
High quality testing equipment is essential for accurate results. Faulty equipment results in erroneous test results. Use only suitable test leads,
terminals, and probe tips.

Diagnostic System Check

Diagnostic Chart
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 3
Chevrolet Venture V6-3.4L VIN E 268

Refer to Engine Controls Schematics. See: Diagrams/Electrical Diagrams

CIRCUIT DESCRIPTION
The Powertrain On Board Diagnostic (OBD) System Check must be the starting point for any driveability complaint diagnosis. Before using this
procedure, you should perform a careful visual/physical inspection of the PCM and engine grounds for being clean and tight. The Powertrain On
Board Diagnostic (OBD) System Check is an organized approach to identifying a problem created by an electronic engine control system
malfunction.

MIL OPERATION
The Malfunction Indicator Lamp (MIL) is located on the instrument panel and is displayed as CHECK ENGINE lamp.

MIL FUNCTION
^ The MIL informs the driver that a malfunction has occurred and the vehicle should be taken in for service as soon as possible
^ The MIL illuminates during a bulb test and a system test
^ A DTC will be stored if a MIL is requested by the diagnostic

MIL ILLUMINATION
^ The MIL will illuminate with ignition switch ON and the engine not running
^ The MIL will turn OFF when the engine is started
^ The MIL will remain ON if the self-diagnostic system has detected a malfunction
^ The MIL may turn OFF if the malfunction is not present
^ If the MIL is illuminated and then the engine stalls, the MIL will remain illuminated so long as the ignition switch is ON.
^ If the MIL is not illuminated and the engine stalls, the MIL will not illuminate until the ignition switch is cycled OFF, then ON.

POWERTRAIN ON BOARD DIAGNOSTIC (OBD) SYSTEM CHECK


Perform the Powertrain On Board Diagnostic (OBD) System Check, when the following conditions are present:
^ When the MIL does not turn ON when the ignition switch is turned to the RUN position. See above for MIL Operation
^ When the MIL remains ON while the engine is running
^ When the MIL is flashing while the engine is running
^ When a driveability symptom is determined

DIAGNOSTIC AIDS
An intermittent may be caused by a faulty connection, rubbed through wire insulation, or a wire broken inside the insulation. Inspect for faulty
connections or a damaged harness. Inspect the PCM harness and connectors for improper mating, broken locks, improperly formed or damaged
terminals, faulty terminal to wire connection, and damaged harness. Refer to Intermittent Conditions. See: Computers and Control
Systems/Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic Strategies/Intermittent Conditions

TEST DESCRIPTION
The numbers below refer to the step numbers on the diagnostic table:
1. The MIL should be ON steady with the key ON/ engine OFF. If not, the No Malfunction Indicator Lamp table should be used to isolate the
malfunction.
2. This test ensures that the PCM is capable of transmitting Class II serial data to the DLC and that the Class II data circuit is not open or
shorted. If a problem is encountered and a malfunctioning scan tool is suspected, try the scan tool on another vehicle to verify operation. If a
DLC problem exists, the DLC Diagnosis table should be used to diagnose the condition.
4. If the engine will not start, the Engine Cranks But Will Not Run table should be used to diagnose the condition. See: Computers and Control
Systems/Testing and Inspection/Symptom Related Diagnostic Procedures
5. The scan tool may display DTCs which are diagnosed in Automatic Transaxle Diagnosis. Refer to DTC List for a complete list of DTCs
supported by this vehicle application. See: Computers and Control Systems/Testing and Inspection/Diagnostic Trouble Code Descriptions

If multiple DTCs are stored, diagnose each DTC according the following priority:
^ PCM Error DTCs
^ System Voltage DTCs
^ Component Level DTCs (switches, sensor range/performance, sensor high voltage, sensor low voltage, ODMs, etc.)
^ System level DTCs (Fuel trim, Misfire, EGR flow, TWC System, Idle Control System, HO2S Response or HO2S Transition Time Ratio)
^ System Reference DTCs
6. A scan tool parameter which is not within the typical range may help to isolate the area which is causing the problem.
Strategy Based Diagnostics
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 4
Chevrolet Venture V6-3.4L VIN E 269

Strategy Based Diagnosis

The goal of Strategy Based Diagnostics is to provide guidance when you create a plan of action for each specific diagnostic situation. Following a
similar plan for each diagnostic situation, you will achieve maximum efliciency when you diagnose and repair vehicles. Although each of the
Strategy Based Diagnostics boxes is numbered, you are not required to complete every box in order to successfully diagnose a customer concern.
The first step of your diagnostic process should always be, Verify the Customer Concern (box 1). The final step of your diagnostic process should
be, Repair and Verify the Fix (box 7). Refer to the chart for the correct strategy based diagnostics.

(1) Verify the Customer Concern: The first part of this step is to obtain as much information as possible from the customer such as: Are there
aftermarket accessories on the vehicle? When does the condition occur? Where does the condition occur? How long and how often does the
condition occur? In order to verify the concern the technician should know the normal operation of the system and refer to the owner or service
manual for any information needed.

(2) Preliminary Checks: Conduct a thorough visual inspection. Review the service history. Detect unusual sounds or odors. Gather diagnostic
trouble code information in order to achieve an effective repair.

(3) Perform Diagnostic System Checks: One or more DTCs may not support a system. System checks verify the proper operation of the system.
This will lead the technician in an organized approach to diagnostics.

(4) Check Bulletins and Other Service Information: Such as videos, newsletters, and the Pulsat programs.

(5.1) Stored DTCs: Follow the designated DTC table exactly in order to make an effective repair.

(5.2) Symptom No DTC: Select the symptom from the symptom tables. Follow the diagnostic steps or suggestions in order to complete the repair,
or refer to the applicable component system check.

(5.3) No Diagnostics: Analyze the concern. Develop a plan for the diagnostics. Schematics will help you to see system power, ground, input and
output circuits. You can also identify splices and other areas where multiple circuits are tied together. Look at component locations to see if
components, connectors or harnesses may be exposed to extreme temperature, moisture, road salt or other corrosives (battery acid, oil or other
fluids). Utilize the wiring diagrams, system description and operation, and system circuit description.

(5.4) Intermittents: An intermittent condition is one that does not occur continuously and will occur when certain conditions are met. Generally,
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 5
Chevrolet Venture V6-3.4L VIN E 270
intermittents are caused by: Faulty electrical connections and wiring, malfunctioning components, electromagnetic radio frequency interference,
and aftermarket equipment.. Combine the technician knowledge with efficient use of the available service information. Evaluate the symptoms and
conditions described by the customer. Use a check sheet or other method in order to identify the component. Follow the suggestions for intermittent
diagnosis. The Tech 1, Tech 2 scan tools, and the J39200 (Fluke 87) have data capturing capabilities that can assist in detection of intermittents.

(5.5) Vehicle Operates as Designed: This condition exists when the vehicle is found to operate normally. The condition described by the customer
may be normal. Verify against another like vehicle that is operating normally under the same conditions described by the customer. Explain your
findings and the operation of that system to the customer.

(6) Re-examine the Concern: If a technician cannot successfully find or isolate the concern, a reevaluation is necessary. Re-verify the concern.
The concern could be an intermittent or normal.

(7) Repair and Verify Fix: After isolating the cause, make the repairs and validate for proper operation. Verify that the symptom has been
corrected which may involve road testing the vehicle.
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 1
Chevrolet Venture V6-3.4L VIN E 271
Ignition System: Component Tests and General Diagnostics

Diagnostic Chart (Part 1 Of 2)


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 2
Chevrolet Venture V6-3.4L VIN E 272

Diagnostic Chart (Part 2 Of 2)

Refer to Engine Controls Schematics Ignition System, Knock Sensor. See: Diagrams/Electrical Diagrams

CIRCUIT DESCRIPTION
During cranking, the IC Module monitors the 7X CKP sensor input for recognition of the sync signal. The sync signal is used only by the IC
Module for synchronization at start-up to determine the correct cylinder pair to spark. Once the engine speed reaches approximately 600 RPM
the PCM sends 5.0 V to the bypass control circuit at the IC Control Module causing the IC control circuit to become ungrounded allowing the
24X signal to be used for better low engine speed performance. At higher engine speeds (1650+) the PCM uses the 3X reference pulses to
control ignition timing because a higher resolution signal is not needed.

Conventional ignition coils have one end of the secondary winding connected to the engine ground. In this ignition system, neither end of the
secondary winding is grounded. Instead, each end of a coil's secondary winding is attached to a spark plug. Each cylinder is paired with the
cylinder that is opposite it (1-4, 2-5, 3-6). These two plugs are on companion cylinders, i.e., on top dead center at the same time. When the coil
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 3
Chevrolet Venture V6-3.4L VIN E 273
discharges, both plugs fire at the same time to complete the series circuit. The cylinder on compression is said to be the event cylinder and the
one on exhaust is the waste cylinder. The cylinder on the exhaust stroke requires very little of the available energy to fire the spark plug. The
remaining energy will be used as required by the cylinder on the compression stroke. The same process is repeated when the cylinders reverse
roles. This method of ignition is called a waste spark ignition system.

This table assumes there are no Ignition System, Fuel Injector, Cam Sensor, or Crank Sensor DTC's present. The Electronic Ignition System
Check tests for faulty ignition coils, spark plugs, plug wires, the 7X Crank Sensor, and IC Module. This table requires the J 26792 Spark Tester.

DIAGNOSTIC AIDS
Inspect for the following conditions:

IMPORTANT: Remove any debris from the connector surfaces before servicing a component. Inspect the connector gaskets when diagnosing
or replacing a component. Ensure that the gaskets are installed correctly. The gaskets prevent contaminate intrusion.

- Poor terminal connection-Inspect the harness connectors for backed out terminals, improper mating, broken locks, improperly formed or
damaged terminals, and faulty terminal to wire connection. Use a corresponding mating terminal to test for proper tension. Refer to
Diagrams.
- Damaged harness-Inspect the wiring harness for damage. If the harness inspection does not reveal a problem, observe the display on the scan
tool while moving connectors and wiring harnesses related to the sensor. A change in the scan tool display may indicate the location of the
fault. Refer to Diagrams.
- PCM and engine grounds for clean and secure connections

If the DTC is determined to be intermittent, reviewing the Failure Records can be useful in determining when the DTC was last set.

TEST DESCRIPTION
Numbers below refer to the step numbers on the Diagnostic Table:
2. It is necessary to disconnect the 24X Crank Sensor to ensure that the 7X signal is being read in the 3X reference parameter on the scan tool.
3. The J 26792 spark tester presents a more difficult load on the secondary ignition than a normal spark plug. If a miss, stumble, or hesitation is
being caused by a spark plug not firing, the spark tester should also not fire.
4. Use a 5% saltwater solution in a spray bottle to induce voltage arching to ground through faulty insulation of spark plug wires.
6. If the no spark condition follows the suspected coil, that coil is faulty. Otherwise, the ignition module is the cause of no spark. This test could
also be performed by substituting a known good coil for the one causing the no spark condition.
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 1
Chevrolet Venture V6-3.4L VIN E 274
Number One Cylinder: Locations
NUMBER 1 CYLINDER

For ignition system firing order, See: Firing Order/Specifications

See: Ignition Cable


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 1
Chevrolet Venture V6-3.4L VIN E 275
Timing Marks and Indicators: Locations
Crankshaft Rotation

Crankshaft Rotation (Typical Crankshaft Pulley)

CRANKSHAFT ROTATION
Crankshaft rotation is clockwise when viewed from in front of the crankshaft pulley as shown in the "Typical Rotation" image.
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 1
Chevrolet Venture V6-3.4L VIN E 276
Camshaft Position Sensor: Service and Repair

REMOVAL PROCEDURE
1. Turn OFF the ignition.
2. Remove the serpentine drive belt.
3. Disconnect the sensor electrical connector.
4. Remove the attaching bolt.
5. Remove the sensor.
6. Inspect the sensor for wear, cracks or leakage if the sensor is not being replaced.

INSTALLATION PROCEDURE
1. Lubricate the O-ring with clean engine oil. Replace the O-ring if the O-ring is damaged.

NOTE: Refer to Fastener Notice in Service Precautions.

2. Install the camshaft position sensor.

Tighten
Tighten the retaining bolt to 10 N.m (8 lb ft).

3. Connect the sensor electrical connector.


4. Reinstall the serpentine drive belt.
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 1
Chevrolet Venture V6-3.4L VIN E 277
Crankshaft Position Sensor: Service and Repair
CKP System Variation Learn Procedure
The crankshaft position system variation compensating values are stored in the PCM non-volatile memory after a learn procedure has been
performed. If the actual crankshaft position system variation is not within the crankshaft position system variation compensating values stored in
the PCM, DTC P0300 may set. Refer to Diagnostic Aids for DTC P0300.

The Crankshaft Position System Variation Learn Procedure should be performed if any of the following conditions are true:
^ DTC P1336 is set.
^ The PCM has been replaced.
^ The engine has been replaced.
^ The crankshaft has been replaced.
^ The crankshaft harmonic balancer has been replaced.
^ The crankshaft position sensor has been replaced.

IMPORTANT: The scan tool crankshaft position system variation learn function will be inhibited if engine coolant temperature is less than 70°C
(158°F). Allow the engine to warm to at least 70°C (158°F) before attempting the crankshaft position system variation learn procedure.

The scan tool crankshaft position system variation learn function will be inhibited if any Powertrain DTCs other than DTC P1336 are set before or
during the crankshaft position system variation learn procedure. Diagnose and repair any DTCs if set. Refer to applicable DTCs.

The crankshaft position system variation learn function will be inhibited if the PCM detects a malfunction involving the camshaft position signal
circuit, the 3X reference circuit, or the 24X reference circuit. If a malfunction has been indicated, refer to the following list to diagnoses the system
or sensor.
^ DTC P0336 Crankshaft Position (CKP) Sensor Performance.
^ DTC P1374 Crankshaft Position (CKP) High to Low Resolution Frequency Correlation.
^ DTC P0341 Camshaft Position (CMP) Sensor Performance.

The scan tool crankshaft position system variation learn function will not be enabled until engine coolant temperature reaches 70°C (158°F)

Selecting the crankshaft position system variation learn procedure on the scan tool will command the PCM to enable CKP system variation learn
fuel cutoff and allow the crankshaft position system variation compensating values to be stored in the PCM. The PCM must detect an engine speed
of 5150 RPM (CKP system variation learn fuel cutoff) during the crankshaft position system variation learn procedure to store the crankshaft
position system variation compensating values and complete the procedure.

IMPORTANT: Set the vehicle parking brake and block the drive wheels when performing the Crankshaft Position System Variation Learning
Procedure in order to prevent personal injury. Release the throttle when the engine reaches the second fuel cut off. Leaving the throttle open during
the fuel cut off will allow the engine to decel at an even rate. Once the learn procedure is completed, the PCM will return the engine control to the
operator and the engine will respond to the throttle position.

1. Set the parking brake.


2. Block the drive wheels.
3. Ensure the hood is closed.
4. Start the engine and allow engine coolant temperature to reach at least 70°C (158°F).
5. Turn off the ignition switch.
6. Select and enable the crankshaft position variation learn procedure with the scan tool.
7. Start the vehicle.
8. Apply and hold the service brake pedal firmly.
9. Ensure the transaxle is in park.
10. Increase accelerator pedal position until the fuel cutoff is reached at 5150 RPM. Release the accelerator pedal after the second fuel cutoff has
been reached.
11. The crankshaft position system variation compensating values are learned when the RPM decreases back to idle. If the procedure terminates.
12. Observe DIG status for DIG P1336.
13. If the scan tool indicates that DIG P1336 ran and passed, the crankshaft position system variation learn procedure is complete. If the scan tool
indicates DTC P1336 failed or not run, determine if other DTCs have set. If DTCs other than P1336 are not set, repeat the crankshaft position
system variation learn procedure as necessary.
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 1
Chevrolet Venture V6-3.4L VIN E 278
Crankshaft Position Sensor: Service and Repair
Crankshaft Position (CKP) Sensor Replacement (7X)

REMOVAL PROCEDURE
1. Turn OFF the ignition switch.
2. Raise the vehicle. Refer to Lifting and Jacking the Vehicle in General Information.
3. Disconnect the sensor electrical connector.
4. Remove the attaching bolt/screw.
5. Remove the sensor from the engine.
6. Inspect for wear, cracks, or leakage if the sensor is not being replaced.

INSTALLATION PROCEDURE
1. Lubricate the O-ring with clean engine oil before installation. Replace the O-ring if the O-ring is damaged.
2. Install the sensor to the block.

NOTE: Refer to Fastener Notice in Service Precautions.

3. Reinstall the sensor attaching Bolt.

Tighten
Tighten the bolt to 8 N.m (71 lb in).

4. Connect the sensor electrical connector.


5. Lower the vehicle.
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 1
Chevrolet Venture V6-3.4L VIN E 279
Crankshaft Position Sensor: Service and Repair
Crankshaft Position (CKP) Sensor Replacement (24X)

REMOVAL PROCEDURE
1. Turn OFF the ignition.
2. Remove the serpentine drive belt from the crankshaft pulley.
3. Raise the vehicle on hoist. Refer to Lifting and Jacking the Vehicle in General Information.
4. Remove the right front Tire and Wheel assembly.
5. Remove the right front engine splash shield.
6. Remove the crankshaft harmonic balancer.
7. Note the routing of sensor harness before removal.
8. Remove the harness retaining clip with bolt (1).
9. Disconnect the sensor electrical connector.
10. Remove the sensor bolts (2).
11. Remove the sensor.

INSTALLATION PROCEDURE
1. Install the 24X crankshaft position sensor with the bolts (2) and route the harness as noted during removal.

NOTE: Refer to Fastener Notice in Service Precautions.

2. Install the harness retaining clip with the bolt (1).

Tighten
Tighten the bolts to 10 N.m (8 lb ft).

3. Connect the sensor electrical connector.


4. Reinstall the balancer on the crankshaft. Refer to Harmonic BalancerInstallation in Engine.
5. Lower the vehicle.
6. Reinstall the serpentine drive belt.
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 1
Chevrolet Venture V6-3.4L VIN E 280
Ignition Cable: Service and Repair
REMOVAL PROCEDURE

1. Turn the ignition OFF.

NOTE: Twist the spark plug boot one-half turn in order to release the boot. Pull on the spark plug boot only. Do not pull on the spark plug
wire or the wire could be damaged.

2. Remove the spark plug wire(s) (2, 4 and 6) from the engine left side spark plug(s).
3. Remove the spark plug wire(s) from the retaining clips.
4. Rotate the engine forward. Refer to Rotating the Engine for Service Access in Engine.

5. Remove the spark plug wire(s) (1, 3 and 5) from the engine right side spark plug(s).
6. Remove the spark plug wire(s) from the retaining clips.

7. Remove the spark plug wire(s) from the ignition coil(s).


8. Remove the spark plug wire(s) from the engine.
9. If you are replacing the spark plug wires, transfer any of the following components:
^ Boot heat shields
^ Spark plug wire conduit
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 2
Chevrolet Venture V6-3.4L VIN E 281
^ Spark plug wire retaining clips

INSTALLATION PROCEDURE

1. Install the spark plug wire(s) to the engine.


2. Install the spark plug wire(s) to the ignition coil(s).

3. Install the spark plug wire(s) (1, 3 and 5) to the engine right side spark plug(s).
4. Install the spark plug wire(s) to the retaining clips.
5. Return the engine to the proper position. Refer to Rotating the Engine for Service Access in Engine.

6. Install the spark plug wire(s) (2, 4 and 6) to the engine left side spark plug(s).
7. Install the spark plug wire(s) to the retaining clips.
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 1
Chevrolet Venture V6-3.4L VIN E 282
Ignition Coil: Service and Repair

REMOVAL PROCEDURE
1. Disconnect the spark plug wires. Note the position from which the wires are removed.
2. Remove the 2 screws securing the ignition coil to the ignition control module.
3. Remove the ignition coil.

INSTALLATION PROCEDURE
1. Install the ignition coil.

NOTE: Refer to Fastener Notice in Service Precautions.

2. Reinstall the 2 attaching screws.

Tighten
Tighten the screws to 4-5 N.m (40 lb in).

3. Reconnect the spark plug wires.


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 1
Chevrolet Venture V6-3.4L VIN E 283
Ignition Control Module: Service and Repair

REMOVAL PROCEDURE
1. Disconnect all the electrical connectors at the ignition control module.
2. Note position of spark plug wires for installation and disconnect the spark plug wires from ignition coils.
3. Remove the screws securing coil assemblies to ignition control module.
4. Disconnect the coils from ignition control module.
5. Remove the fasteners securing ignition control module assembly to engine.
6. Remove the ignition control module from the bracket.

INSTALLATION PROCEDURE
1. Install the ignition control module on the bracket.
2. Install the coils to ignition control module.
3. Reinstall the fasteners securing ignition control module assembly to engine.

NOTE: Refer to Fastener Notice in Service Precautions.

4. Reinstall the screws.

Tighten
Tighten the screws to 4-5 N.m (40 lb in).

5. Connect the spark plug wires as noted during removal.


6. Connect the electrical connectors to the ignition control module.
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 1
Chevrolet Venture V6-3.4L VIN E 284
Knock Sensor: Service and Repair
REMOVAL PROCEDURE

1. Turn OFF the ignition.


2. Raise the vehicle. Refer to Lifting and Jacking the Vehicle in Service Precautions.
3. Disconnect the wiring harness connector from the knock sensor.
4. Remove the knock sensor from the engine block.

INSTALLATION PROCEDURE

IMPORTANT: DO NOT apply thread sealant to the sensor threads. The sensor threads are coated at the factory and applying additional sealant
affects the sensor's ability to detect detonation.

1. Install the knock sensor into engine block.

Tighten
19 N.m (14 lb ft).

2. Connect the knock sensor wiring harness connector to the knock sensor.
3. Lower the vehicle.
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 1
Chevrolet Venture V6-3.4L VIN E 285
Steering Column: Service and Repair

Tilt Head Housing - Assemble


Assembly Procedure

- Tools Required
- J23653-SIR Lock Plate Compressor

1. Align the race and upper shaft assembly (1) to the 12 o'clock position.
2. Put the lock cylinder in the LOCK position and remove the key.

3. Install the inner race (5).


4. Install the upper bearing inner race seat (4).
5. Install the upper bearing spring (3).
6. Lubricate the turn signal cancel cam assembly (2) using grease kit 26001884.
7. Install the turn signal cancel cam assembly (2).
8. Install the shaft lock shield assembly (1).

9. Install the bearing retaining using J 23653-SIR.


10. Remove J23653-SIR from the steering column.
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 2
Chevrolet Venture V6-3.4L VIN E 286

11. Install the wave washer.


12. Install the SIR coil assembly. Refer to Inflatable Restraint
Steering Wheel Module Coil - Assemble - Off Vehicle.

Tilt Head Housing - Disassemble


Disassembly Procedure

- Tools Required
- J23653-SIR Lock Plate Compressor

1. Remove the SIR coil assembly. Refer to Inflatable Restraint Steering Wheel Module Coil -Disassemble - Off Vehicle.

2. Remove the wave washer.

3. Remove the bearing retainer using J 23653-SIR and dispose of it.


4. Remove J 23653-SIR from the steering column.
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 3
Chevrolet Venture V6-3.4L VIN E 287

5. Remove the shaft lock shield assembly (1).


6. Remove the turn signal cancel cam assembly (2).
7. Remove the upper bearing spring (3).
8. Remove the upper bearing inner race (4).
9. Remove the inner race (5).

Tilt Lever
Removal Procedure

Pull the tilt lever in order to remove the tilt lever from the steering column.

Installation Procedure

Push the tilt lever onto the tilt lever shaft in order to install the tilt lever.

Tilt Spring - Assemble


Assembly Procedure
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 4
Chevrolet Venture V6-3.4L VIN E 288

1. Install the spring guide (1) to the tilt spring (2). Lubricate the spring guide with lithium grease.

Caution: The tilt spring and the spring guide are under pressure and could become and projectile. During the disassembly and
assembly procedures, secure the tilt spring with locking pliers. Exercise caution when removing or installing the tilt spring and the
spring guide, as bodily injury may result.

2. Install the tilt spring (1).


2.1. Install the tilt spring (1) to the post on the steering column support assembly (2).
2.2. Secure the tilt spring (1) with locking pliers.
3. Install the upper and lower shrouds. Refer to Steering Column Trim Covers - Assemble - Off Vehicle.
Tilt Spring - Disassemble
Disassembly Procedure
1. Remove the upper and lower shrouds. Refer to Steering Column Trim Covers - Disassemble -
Off Vehicle.

2. Use the tilt lever to tilt the column in the "UP" position.

Caution: The spring and the spring guide are under pressure and could become a projectile. During the disassembly and assembly
procedures, secure the tilt spring with locking pliers. Exercise caution when removing or installing the tilt spring and the spring
guide, as bodily injury may result.
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 5
Chevrolet Venture V6-3.4L VIN E 289

3. Remove the tilt spring (1).


3.1. Pry the tilt spring up until a bulge occurs and most of the tilt spring tension is removed.
3.2. Secure the tilt spring with locking pliers and continue prying until the tilt spring disengages from the post of the steering column support
assembly (3).

4. Remove the spring guide (1) from the tilt spring (2).

A/T Shift Lock Control - Assemble


Assembly Procedure

1. Install the electrical BTSI actuator.


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 6
Chevrolet Venture V6-3.4L VIN E 290

2. Adjust the electrical BTSI actuator.


2.1. Pull the tab (1) out on the block side (2) of the electrical BTSI actuator.
2.2. Shift the column into the neutral position.
2.3. Press on the adjuster block (2) to compress the internal adjuster spring to disengage the adjuster teeth. Slide the adjuster block as far
away from the solenoid as possible.
2.4. Shift the column into the park position.
2.5. Lock in place by pushing the tab (1) back in.
3. Inspect the electrical BTSI actuator.
3.1. The electrical BTSI actuator must lock the gear shift lever when it is put into the park position.
3.2. When the column is installed in the vehicle you will not be able to shift the gear shift lever out of the park position without pressing on
the brake pedal. The solenoid will be energized.
3.3. Readjust if needed.
4. Install the upper and lower shrouds. Refer to Steering Column Trim Covers - Assemble -Off Vehicle.

A/T Shift Lock Control - Disassemble


Disassembly Procedure
1. Remove the upper and lower shrouds. Refer to Steering Column Trim Covers - Disassemble -Off Vehicle.

2. Use a screwdriver to pry the electrical BTSI actuator from the steering column jacket assembly.
3. Remove the electrical BTSI actuator from the steering column.

A/T Shift Lock Control Actuator


Removal Procedure
1. Turn the ignition OFF.
2. Remove the lower steering column shroud. Refer to Steering Column Trim Covers - Disassemble -Off Vehicle.
3. Remove the shift lock control from the steering column. Refer to Automatic Transmission Shift Lock Control - Disassemble - Off Vehicle.

Installation Procedure
1. Install the shift lock control to the steering column. Refer to Automatic Transmission Shift Lock Control - Assemble - Off Vehicle.
2. Remove the lower steering column shroud. Refer to Steering Column Trim Covers - Assemble - Off Vehicle.
Electronic Column Lock Module
Removal Procedure

Caution: Refer to SIR Handling Caution in Service Precautions.

1. Disable the SIR system. Refer to Disabling the SIR System in Air Bags and Seat Belts.
2. Remove the tilt lever. Refer to Tilt Lever Replacement - On Vehicle.
3. Remove the steering wheel. Refer to Steering Wheel Replacement.
4. Remove the ignition lock cylinder. Refer to Ignition Lock Cylinder Replacement - On Vehicle (Cylinder Rotates) or Ignition Lock Cylinder
Replacement - On Vehicle (Unable to Rotate Cylinder).
5. Remove the steering column trim covers. Refer to Steering Column Trim Covers - Disassemble - Off Vehicle.
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 7
Chevrolet Venture V6-3.4L VIN E 291
6. Remove the lock module assembly. Refer to Electronic Column Lock Module - Disassemble - Off Vehicle.

Installation Procedure
1. Install the lock module assembly. Refer to Electronic Column Lock Module - Assemble - Off Vehicle.
2. Install the steering column trim covers. Refer to Steering Column Trim Covers - Assemble - Off Vehicle.
3. Install the ignition lock cylinder. Refer to Ignition Lock Cylinder Replacement - On Vehicle (Cylinder Rotates) or Ignition Lock Cylinder
Replacement - On Vehicle (Unable to Rotate Cylinder).
4. Install the steering wheel. Refer to Steering Wheel Replacement.
5. Install the tilt lever. Refer to Tilt Lever Replacement - On Vehicle.
6. Enable the SIR system. Refer to Enabling the SIR System in Air Bags and Seat Belts.

Electronic Column Lock Module - Assemble


Assembly Procedure
1. Install the lock module assembly (1).

Notice: Refer to Fastener Notice in Service Precautions.

2. Install the 3 pan head tapping screws (2) into the lock module assembly.
Tighten the screws to 1.5 Nm (13 inch lbs.).

3. Install the park lock cable assembly (1) into the lock module assembly.
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 8
Chevrolet Venture V6-3.4L VIN E 292

4. Install the ignition and key alarm switch assembly (3) onto the lock module assembly (2) and secure by using 2 tapping screws.
- Tighten the screws to 4.7 Nm (42 inch lbs.).

5. Slide the PASSKEY 111 (2) onto the lock module assembly (1).
6. Install the steering column tilt head assembly. Refer to Steering Column Tilt Head Housing - Assemble - Off Vehicle.

Electronic Column Lock Module - Disassemble


Disassembly Procedure
1. Remove the steering column tilt head assembly. Refer to Steering Column Tilt Head Housing -Disassemble - Off Vehicle.

2. Slide the PASSKEY 111 (2) off of the lock module assembly (1).
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 9
Chevrolet Venture V6-3.4L VIN E 293

3. Remove the key alarm connector (1) from the lock module assembly (2).
4. Remove the 2 tapping screws from the ignition key alarm switch assembly (3).
5. Let both parts hang freely.

6. Remove the park lock cable assembly (1) from the lock module assembly.

7. Remove 3 pan head tapping screws (2) from the lock module assembly (1).
8. Remove the lock module assembly (1).

Ignition & Key Alarm Switch - Assemble


Assembly Procedure

Notice: Refer to Fastener Notice in Service Precautions.


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 10
Chevrolet Venture V6-3.4L VIN E 294

1. Install the ignition and key alarm switch assembly (3) onto the lock module assembly (2) and secure by using 2 tapping screws.
- Tighten the screws to 4.7 Nm (42 inch lbs.).
2. Install the key alarm connector (1) into the lock module assembly (2).

3. Slide the PASS KEY III (2) onto the lock module assembly (1).

4. Slide the turn signal switch assembly connectors (2) to the bulkhead connector (1).
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 11
Chevrolet Venture V6-3.4L VIN E 295

5. Install the wire harness assembly (4) into the wire harness strap (5).
6. Install the wire harness strap (2) into the steering column tilt head assembly (1).
7. Install the wire harness straps (3) onto the wire harness assembly (4).
8. Install the upper and lower shrouds. Refer to Steering Column Trim Covers - Assemble -Off Vehicle.

Ignition & Key Alarm Switch - Disassemble


Disassembly Procedure
1. Remove the upper and lower shrouds. Refer to Steering Column Trim Covers - Disassemble - Off Vehicle.

2. Remove the wire harness assembly (4) from the wire harness strap (5).
3. Remove the wire harness straps (3) from the wire harness assembly (4).
4. Remove 1 wire harness strap (2) from the upper tilt head assembly (1).

5. Slide the turn signal switch assembly connectors (2) out from the bulk head connector (1).
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 12
Chevrolet Venture V6-3.4L VIN E 296

6. Pull the PASS KEY III (2) off of the lock module assembly (1).

7. Remove the key alarm connector (1) from the lock module assembly (2).
8. Remove the 2 tapping screws from the ignition key alarm switch assembly (3).
Ignition Lock Cylinder - Rotates
Removal Procedure
1. Disconnect the battery negative cable. Refer to Battery Negative Cable Disconnect/Connect Procedure in Starting and Charging.

Caution: Refer to SIR Handling Caution in Service Precautions.

2. Disable the SIR system. Refer to Disabling the SIR System in Air Bags and Seat Belts.
3. Remove the inflator module. Refer to Inflatable Restraint Steering Wheel Module Replacement in Air Bags and Seat Belts.
4. Remove the steering wheel. Refer to Steering Wheel Replacement.
5. Remove the tilt lever.
6. Remove ONLY the steering column LOWER shroud. Refer to Steering Column Trim Covers - Disassemble - Off Vehicle.
7. Remove the steering column upper shroud FASTENERS ONLY.

8. Lift the upper steering column shroud in order to gain access to the lock cylinder access hole (1).
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 13
Chevrolet Venture V6-3.4L VIN E 297
9. Insert the bent tip awl into the ignition lock cylinder access hole (1).

10. Turn the ignition lock cylinder to START.

11. Use the bent tip awl in order to push down on the ignition lock cylinder retainer.
12. Release the ignition lock cylinder to RUN.

13. Remove the ignition lock cylinder from the lock module.

Installation Procedure
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 14
Chevrolet Venture V6-3.4L VIN E 298

1. Insert the ignition lock cylinder through the upper shroud.


2. Align the lock cylinder retaining tab and the position tab with the slots in the lock housing.
3. Push the lock cylinder into the lock housing completely.
4. Install the steering column upper shroud. Refer to Steering Column Trim Covers - Assemble - Off Vehicle.
5. Install the lower shroud. Refer to Steering Column Trim Covers - Assemble - Off Vehicle.
6. Install the tilt wheel lever.
7. Install the steering wheel. Refer to Steering Wheel Replacement
8. Install the inflator module. Refer to Inflatable Restraint Steering Wheel Module Replacement in Air Bags and Seat Belts.
9. Enable the SIR system. Refer to Enabling the SIR System in Air Bags and Seat Belts.
10. Connect the battery negative cable. Refer to Battery Negative Cable Disconnect/Connect Procedure in Starting and Charging.

Ignition Lock Cylinder - Unable to Rotate Cylinder


Removal Procedure

1. Disconnect the battery negative cable. Refer to Battery Negative Cable Disconnect/Connect Procedure in Starting and Charging.

Caution: Refer to SIR Handling Caution in Service Precautions.

2. Disable the SIR system. Refer to Disabling the SIR System in Air Bags and Seat Belts.
3. Remove the inflator module. Refer to Inflatable Restraint Steering Wheel Module Replacement in Air Bags and Seat Belts.
4. Remove the steering wheel. Refer to Steering Wheel Replacement.
5. Remove the tilt lever.
6. Remove ONLY the steering column LOWER shroud. Refer to Steering Column Trim Covers - Disassemble - Off Vehicle.
7. Remove the SIR coil. Refer to Inflatable Restraint Steering Wheel Module Coil Replacement in Air Bags and Seat Belts.
8. Remove the shaft lock shield and the turn signal cancel cam. Refer to Steering Column Tilt Head Housing - Disassemble - Off Vehicle
Steering Column Tilt Head Disassemble.
9. Remove the steering column upper shroud FASTENERS ONLY.
10. Remove the park lock cable from the lock module.

Important: The lock bolt has spring tension from the lock bolt spring. Hold the lock bolt while you remove the lock module.

11. Remove the lock module with the ignition switch, the theft deterrent module and the steering column upper shroud. Refer to Electronic
Column Lock Module - Disassemble - Off Vehicle.
12. Remove the lock module rear cover in order to gain access to the lock module sector gears.

Important: Make a mark (1) on both of the lock module sector gears in order to ensure proper sector gear timing after the lock module is
assembled.

13. Remove the lock module sector gears.


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 15
Chevrolet Venture V6-3.4L VIN E 299

14. Use a small burring tool in order to carefully remove the lock cylinder position tab.
15. Use a small flat-bladed tool in order to press and hold the lock cylinder retainer (1).
16. Remove the lock cylinder from the lock module.
17. Remove all of the metal shavings from the lock module.

18. Record the lock cylinder four-character key code (1) on the lock cylinder.
19. Cut a new key according to the four-character lock cylinder key code. Refer to Key and Lock Cylinder Coding.
20. Ensure that the new ignition key operates in all of the vehicle lock cylinders.
21. Code the NEW ignition lock cylinder according to the four-character lock cylinder key code. Refer to Key and Lock Cylinder Coding.

Installation Procedure

1. Align the marks (1) on the lock module sector gears and install the sector gears.
2. Ensure that the lock module is in the OFF/LOCK position.
3. Insert the ignition key into the NEW ignition lock cylinder.
4. Align the lock cylinder retaining tab and the position tab with the slots in the lock housing.
5. Push the lock cylinder into the lock housing completely.
6. Rotate the lock cylinder to ACC.
7. Ensure that the sector gear arrows point toward each other. If the sector gear arrows do not point toward each other, remove the sector gears
and install the sector gears properly.
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 16
Chevrolet Venture V6-3.4L VIN E 300
8. Install lock module rear cover.
9. Push the lock bolt completely into the into the tilt head and hold the lock bolt.
10. Install the lock module with the ignition switch, the theft deterrent module and the steering column upper shroud. Refer to Electronic Column
Lock Module - Assemble - Off Vehicle.
11. Install the park lock cable to the lock module.
12. Adjust the park lock cable.
13. Install the steering column lower shroud. Refer to Steering Column Trim Covers - Assemble - Off Vehicle.
14. Install the turn signal cancel cam and the shaft lock shield. Refer to Steering Column Tilt Head Housing - Assemble - Off Vehicle.
15. Install the SIR coil. Refer to Inflatable Restraint Steering Wheel Module Coil Replacement in Air Bags and Seat Belts.
16. Install the steering wheel. Refer to Steering Wheel Replacement.
17. Install the inflator module. Refer to Inflatable Restraint Steering Wheel Module Replacement in Air Bags and Seat Belts.
18. Enable the SIR system. Refer to Enabling the SIR System in Air Bags and Seat Belts.
19. Connect the battery negative cable. Refer to Battery Negative Cable Disconnect/Connect Procedure in Starting and Charging.
Ignition Switch
Removal Procedure

Caution: Refer to SIR Handling Caution in Service Precautions.

1. Disable the SIR system. Refer to Disabling the SIR System in Air Bags and Seat Belts.
2. Disconnect the battery negative cable from the battery. Refer to Battery Negative Cable Disconnect/Connect Procedure in Starting and
Charging.
3. Remove the left side closeout insulator panel. Refer to Closeout/Insulator Panel Replacement - Left in Instrument Panel, Gauges and Wiring
Indicators.
4. Disconnect the steering column electrical connector from the vehicle.
5. Remove the steering column shrouds. Refer to Steering Column Trim Covers - Disassemble -Off Vehicle.
6. Remove the ignition lock cylinder. Refer to Ignition Lock Cylinder Replacement - On Vehicle (Cylinder Rotates) or Ignition Lock Cylinder
Replacement - On Vehicle (Unable to Rotate Cylinder).
7. Remove the ignition switch. Refer to Ignition and Key Alarm Switch Assembly - Disassemble - Off Vehicle.

Installation Procedure

1. Install the ignition switch. Refer to Ignition and Key Alarm Switch Assembly - Assemble - Off Vehicle.
2. Install the ignition lock cylinder. Refer to Ignition Lock Cylinder Replacement - On Vehicle (Cylinder Rotates) or Ignition Lock Cylinder
Replacement - On Vehicle (Unable to Rotate Cylinder).
3. Install the steering column shrouds. Refer to Steering Column Trim Covers - Assemble -Off Vehicle.
4. Connect the steering column electrical connector to the vehicle.
5. Install the left side closeout insulator panel. Refer to Closeout/Insulator Panel Replacement - Left in Instrument Panel, Gauges and Wiring
Indicators.
6. Connect the battery negative cable to the battery. Refer to Battery Negative Cable Disconnect/Connect Procedure in Starting and Charging.
7. Enable the SIR system. Refer to Enabling the SIR System in Air Bags and Seat Belts.
Linear Shift
Removal Procedure

Caution: Refer to SIR Handling Caution in Service Precautions.

1. Disable the SIR system. Refer to Disabling the SIR System in Air Bags and Seat Belts.
2. Remove the tilt lever. Refer to Tilt Lever Replacement - On Vehicle.
3. Remove the ignition lock cylinder. Refer to Ignition Lock Cylinder Replacement - On Vehicle (Cylinder Rotates) or Ignition Lock Cylinder
Replacement -On Vehicle (Unable to Rotate Cylinder).
4. Remove the steering column trim covers. Refer to Steering Column Trim Covers - Disassemble - Off Vehicle.
5. Remove the linear shift assembly. Refer to Linear Shift Assembly - Disassemble - Off Vehicle.

Installation Procedure
1. Install the linear shift assembly. Refer to Linear Shift Assembly - Assemble - Off Vehicle.
2. Install the steering column trim covers. Refer to Steering Column Trim Covers - Assemble - Off Vehicle.
3. Install the ignition lock cylinder. Refer to Ignition Lock Cylinder Replacement - On Vehicle (Cylinder Rotates) or Ignition Lock Cylinder
Replacement - On Vehicle (Unable to Rotate Cylinder).
4. Install the tilt lever. Refer to Tilt Lever Replacement - On Vehicle.
5. Enable the SIR system. Refer to Enabling the SIR System in Air Bags and Seat Belts.

Linear Shift - Assemble


Assembly Procedure

Notice: Refer to Fastener Notice in Service Precautions.

Important: Lubricate all moving parts of the linear shift assembly with synthetic grease.
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 17
Chevrolet Venture V6-3.4L VIN E 301

1. Install the gearshift lever assembly support bracket and secure by using the 3 flat head 6-lobed socket tap screws.
- Tighten the screws to 10 Nm (89 inch lbs.).

2. Insert the cam bushing (2) into the cable shift cam assembly (1).
3. Install the cable shift cam assembly (1).
4. Install the hexagon flange head bolt.
- Tighten the screw to 18 Nm (14 ft. lbs.).

5. Install the park lock cable assembly and secure by using 2 oval head 6-lobed socket tap screws.
- Tighten the screws to 6.5 Nm (58 inch lbs.).
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 18
Chevrolet Venture V6-3.4L VIN E 302

6. Install the shift [ever clevis (1).


7. Install the ball actuator assembly (2).
8. Install the hexagon flanged head bolt.
- Tighten the bolt to 18 Nm (14 ft. lbs.).

9. Install the park lock cable assembly into the lock module assembly (1).
10. Place steering column lock cylinder set into the off position.
11. Place the shift lever clevis into the park position.
12. Press the locking tab on the end of the park lock cable assembly (1) into the slot in the lock module assembly.
13. Inspect the park lock cable assembly by performing the following steps.
13.1. Insert the key into the ignition switch.
13.2. Place the steering column lock cylinder set in the OFF or the LOCK position. The gear shift lever must remain locked in the park
position.
13.3. Place the steering column lock cylinder set in the RUN position.
13.4. Place the gear shift lever in the neutral position.
13.5. With the gear shift lever in the neutral position, the steering column lock cylinder set must remain out of the OFF or the LOCK
position.
13.6. Place the gear shift lever in the park position.
13.7. Put the steering column lock cylinder set in the OFF or the LOCK position.
13.8. Remove the key from the ignition switch.
14. Install the electrical BTSI actuator assembly. Refer to Automatic Transmission Shift Lock Control-Assemble - Off Vehicle.
Linear Shift - Disassemble
Disassembly Procedure
1. Remove the electrical BTSI actuator assembly. Refer to Automatic Transmission Shift Lock Control - Disassemble - Off Vehicle.
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 19
Chevrolet Venture V6-3.4L VIN E 303

2. Remove the park lock cable assembly (1) from the lock module assembly.

3. Remove the hexagon flanged head bolt.


4. Remove the ball and actuator assembly (2).
5. Remove the shift lever clevis (1).

6. Remove the 2 oval head 6-lobed socket tapping screws from the shift gate.

7. Remove the hexagon flange head bolt.


8. Remove the cable shift cam assembly (1).
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 20
Chevrolet Venture V6-3.4L VIN E 304
9. Remove the cam bushing (2) from the cable shift cam assembly (1).

10. Remove 3 flat head 6-lobed socket tapping screws.


11. Remove the gearshift lever assembly support bracket.

Lower/Upper Intermediate Steering Shaft


Removal Procedure
1. Remove the instrument panel left side insulator. Refer to Closeout/Insulator Panel Replacement -Left in Instrument Panel, Gauges and
Wiring Indicators.
2. Pull the intermediate steering shaft seal down off of the steering column in order to access the intermediate steering shaft upper bolt.
3. Remove the intermediate steering shaft upper bolt.
4. Push the intermediate steering shaft down in order to remove the intermediate steering shaft from the steering column. If you are unable to
remove the intermediate shaft, perform the following steps:
4.1. Insert the tip of a large flat-bladed tool into the intermediate steering shaft end slot.
4.2. Twist the large flat-bladed tool in order to loosen the intermediate steering shaft.
5. Raise and support the vehicle. Refer to Vehicle Lifting
6. Remove the left front tire and wheel. Refer to Tire and Wheel Removal and Installation in Wheels, Tires and Alignment.
7. Apply silicone (non petroleum based) lubricant to the intermediate shaft lower seal.
8. Push the intermediate shaft lower seal up into the intermediate shaft upper seal in order to access to the intermediate shaft lower bolt.
9. Remove the intermediate shaft lower bolt.

10. Push the intermediate steering shaft (1) up in order to remove the intermediate steering shaft from the steering gear (2). If you are unable to
remove the intermediate shaft, perform the following steps:
10.1. Insert the tip of a large flat-bladed tool into the intermediate steering shaft end slot.
10.2. Twist the large flat-bladed tool in order to loosen the intermediate steering shaft.
11. Remove the intermediate steering shaft.

Installation Procedure
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 21
Chevrolet Venture V6-3.4L VIN E 305

1. Install the intermediate steering shaft through the intermediate steering shaft seal.
2. Install the intermediate steering shaft to the steering gear.

Notice: Refer to Fastener Notice in Service Precautions.

3. Install the intermediate steering shaft lower bolt.


- Tighten the intermediate steering shaft lower bolt to 48 Nm (35 ft. lbs.).
4. Install the intermediate steering shaft seal to the steering gear.
5. Install the left front tire and wheel. Refer to Tire and Wheel Removal and Installation in Wheels, Tires and Alignment.
6. Lower the vehicle.
7. Install the intermediate steering shaft to the steering column.
8. Install the intermediate steering shaft upper bolt.
- Tighten the intermediate steering shaft upper bolt to 48 Nm (35 ft. lbs.).
9. Install the intermediate steering shaft seal to the steering column.
10. Install the instrument panel left side insulator. Refer to Closeout/Insulator Panel Replacement - Left in Instrument Panel, Gauges and Wiring
Indicators.

Multifunction, Turn Signal & Hazard Switch


Removal Procedure
1. Remove the HEADLAMP circuit breaker.

Caution: Refer to SIR Handling Caution in Service Precautions.

2. Disable the SIR system. Refer to Disabling the SIR System in Air Bags and Seat Belts.
3. Remove the inflatable restraint steering wheel module. Refer to Inflatable Restraint Steering Wheel Module Replacement in Air Bags and
Seat Belts.
4. Remove the steering wheel. Refer to Steering Wheel Replacement.
5. Remove the steering column shrouds. Refer to Steering Column Trim Covers - Disassemble -Off Vehicle.
6. Disconnect the steering column electrical connectors.
7. Remove the turn signal multifunction switch connectors from the steering column electrical connector.
8. Remove the turn signal multifunction switch. Refer to Turn Signal and Multifunction Switch Assembly - Disassemble - Off Vehicle.

Installation Procedure
1. Install the turn signal multifunction switch. Refer to Turn Signal and Multifunction Switch Assembly - Assemble - Off Vehicle.
2. Install the turn signal multifunction switch connectors to the steering column electrical connector.
3. Connect the steering column electrical connectors.
4. Install the steering column shrouds. Refer to Steering Column Trim Covers - Assemble -Off Vehicle.
5. Install the steering wheel. Refer to Steering Wheel Replacement.
6. Install the inflatable restraint steering wheel module. Refer to Inflatable Restraint Steering Wheel Module Replacement in Air Bags and Seat
Belts.
7. Enable the SIR system. Refer to Enabling the SIR System in Air Bags and Seat Belts.
8. Install the HEADLAMP circuit breaker.
Shift Lever
Removal Procedure
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 22
Chevrolet Venture V6-3.4L VIN E 306

1. Roll back the automatic transmission range selector lever seal.


2. Remove the automatic transmission range selector lever screw.
3. Remove the automatic transmission range selector lever.

Installation Procedure
1. Install the automatic transmission range selector lever.

Notice: Refer to Fastener Notice in Service Precautions.

2. Install the automatic transmission range selector lever screw.


- Tighten the automatic transmission range selector lever screw to 20 Nm (14 ft. lbs.).
3. Install the automatic transmission range selector lever seal.
4. Verify that there is a positive shift gate feel in all positions.
Shift Lever - Assemble
Assembly Procedure

1. Install the shift lever seal (2) onto the shift lever assembly (4).

Notice: Refer to Fastener Notice in Service Precautions.

2. Install the shift lever assembly (4) into the linear shift assembly and secure it with a shift lever screw (3).
- Tighten the screw to 20 Nm (27 ft. lbs.).
3. Install the upper and lower shrouds. Refer to Steering Column Trim Covers - Assemble -Off Vehicle.
Shift Lever - Disassemble
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 23
Chevrolet Venture V6-3.4L VIN E 307
Disassembly Procedure
1. Remove the upper and lower shrouds. Refer to Steering Column Trim Covers - Disassemble -Off Vehicle.

2. Remove the shift lever screw (3) from the shift lever assembly (4).
3. Remove the shift lever assembly (4).
4. Remove the shift lever seal (2).

SIR Steering Wheel Module Coil - Centering


Centering Procedure

Notice: Refer to New SIR Coil Is Centered in Service Precautions.

1. Verify the following before centering the SIR coil assembly:


- The wheels on the vehicle are straight ahead.
- The block tooth (1) of the steering shaft assembly is in the 12 o'clock position.
- The ignition switch is in the LOCK position.

2. If the front (5) of the SIR coil assembly has a centering window (4), and on the back side (2) a spring service lock (1), perform the following
steps:
2.1. Hold the coil assembly with the face up.
2.2. While depressing the spring service lock, rotate the coil hub clockwise until the coil ribbon stops.
2.3. Rotate the coil hub slowly, counter clockwise, until the centering window appears yellow and both arrows (3) line up.
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 24
Chevrolet Venture V6-3.4L VIN E 308
2.4. Release spring service lock between the locking tab. The SIR coil is now centered.
2.5. Align the centered SIR coil assembly with the horn tower and slide onto the steering shaft assembly.

3. If the front (4) of the SIR coil has a centering window (3) and no spring service lock on the back side (1), perform the following steps:
3.1. Hold the coil assembly with the face up.
3.2. Rotate the coil hub clockwise until the coil ribbon stops.
3.3. Rotate the coil hub slowly, counter clockwise until the centering window appears yellow and both arrows (2) line up. This is center
position.
3.4. While holding the coil hub in center position, align the SIR coil assembly with the horn tower and slide onto the steering shaft assembly.

4. If no centering window is present on the front side (3) of the SIR coil assembly, but a spring service lock (1) is on the back side (2), perform
the following steps:
4.1. Hold the SIR coil assembly with the back side up.
4.2. While depressing the spring service lock, rotate the coil hub counter clockwise until the coil ribbon stops.
4.3. Still pressing the spring service lock, rotate the coil hub in the opposite direction 2 1/2 revolutions.
4.4. Release the spring service lock between locking tabs. The SIR coil is now centered.
4.5. Align the centered SIR coil assembly with the horn tower and slide onto the steering shaft assembly.

5. For no centering window on the front side (2) of the SIR coil assembly and no spring service lock on the back side (1), perform the following
steps:
5.1. Hold the coil assembly with the face up.
5.2. Rotate the coil hub clockwise until the coil ribbon stops.
5.3. Rotate the coil hub, slowly, counter clockwise, for 2 1/2 revolutions. This is center position.
5.4. While maintaining the coil hub in center position, align the centered SIR coil assembly with the horn tower and slide onto the steering
shaft assembly.
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 25
Chevrolet Venture V6-3.4L VIN E 309
SIR Steering Wheel Module Coil - Disassemble
Disassembly Procedure
1. Remove the upper and lower shrouds. Refer to Steering Column Trim Covers - Disassemble - Off Vehicle.

2. Remove the wire harness assembly (4) from the wire harness strap (5).
3. Remove the wire harness straps (3) from the wire harness assembly (4).
4. Remove 1 wire harness strap (2) from the upper tilt head assembly (1).

5. Remove the retaining ring (1).


6. Remove the SIR coil assembly (2).

Inflatable Restraint Steering Wheel Module Coil - Assemble - Off Vehicle


Assembly Procedure

1. Align the block tooth on the race and upper shaft assembly (1) to the 12 o' clock position.
2. Put the lock cylinder in the LOCK position and remove the key.
3. A new SIR coil assembly will be precentered.
4. If reusing the original SIR coil assembly refer to Inflatable Restraint Coil Centering - Off Vehicle (Column Shift And Floor Shift).
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 26
Chevrolet Venture V6-3.4L VIN E 310

5. Align the SIR coil assembly (2) with the horn tower sticking through the shaft lock shield assembly (1).

Important: The retaining ring (1) must seat securely on the groove of the race and upper shaft assembly (2).

6. Install the retaining ring (1).


7. If using a new SIR coil, remove and dispose of the orange tab.

8. Install the wire harness assembly (4) into the wire harness strap (5).
9. Install the wire harness straps (2) into the steering column tilt head assembly (1).
10. Install the wire harness straps (3) onto the wire harness assembly (4).
11. Install the upper and lower shrouds. Refer to
Steering Column Trim Covers - Assemble -Off Vehicle.
Steering Column
Removal Procedure

- Tools Required
- J 42640 Steering Column Anti-Rotation Pin

Important: If the inflatable restraint module is deployed, inspect the SIR coil. Replace the SIR coil if the SIR coil exhibits any signs of damage
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 27
Chevrolet Venture V6-3.4L VIN E 311
caused by excessive heat.

1. Disconnect the battery ground (negative) cable. Refer to Battery Negative Cable Disconnect/Connect Procedure in Starting and Charging.

Caution: Refer to SIR Handling Caution in Service Precautions.

2. Disable the SIR system. Refer to Disabling the SIR System in Air Bags and Seat Belts.
3. Remove the inflatable restraint steering wheel module. Refer to Inflatable Restraint Steering Wheel Module Replacement in Air Bags and
Seat Belts.
4. Remove the steering wheel. Refer to Steering Wheel Replacement
5. Remove the instrument panel left insulator. Refer to Closeout/Insulator Panel Replacement - Left in Instrument Panel, Gauges and Wiring
Indicators.
6. Push the top of the intermediate shaft seal down in order to access to the intermediate shaft coupling upper bolt.
7. Install the J 42640 to the steering column.

Notice: The wheels of the vehicle must be straight ahead and the steering column in the LOCK position before disconnecting the steering
column or intermediate shaft from the steering gear. Failure to do so will cause the SIR coil assembly to become uncentered, which may
cause damage to the coil assembly.

8. Remove the steering intermediate shaft from the steering column. Refer to Lower/Upper Intermediate Steering Shaft Replacement Steering
Column- Tilt.

9. Remove the transaxle shift cable from the steering column.


10. Disconnect the steering column electrical connectors.
11. Remove the steering column bolts.
12. Remove the steering column nuts.
13. Remove the steering column anchor cable from the bracket stud.
14. Remove the steering column from the vehicle.

Installation Procedure
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 28
Chevrolet Venture V6-3.4L VIN E 312

1. Install the steering column to the vehicle.


2. Install the steering column to the intermediate shaft. Refer to Lower/Upper Intermediate Steering Shaft Replacement
3. Remove the J 42640 from the steering column.
4. Install the steering column anchor cable to the bracket stud.

Caution: In order to ensure the intended function of the steering column in a vehicle during a crash and in order to avoid personal
injury to the driver, perform the following:
- Tighten the steering column lower fasteners before you tighten the steering column upper fasteners. Failure to do this can
damage the steering column.
- Tighten the steering column fasteners to the specified torque. Overtightening the upper steering column fasteners could affect the
steering column collapse.

5. LOOSELY install the steering column nuts.

Notice: Refer to Fastener Notice in Service Precautions.

6. Install the steering column bolts.


- Tighten the steering column fasteners in the proper order.
6.1. Tighten the steering column bolts to 24 Nm (18 ft. lbs.).
6.2. Tighten the steering column nuts to 24 Nm (18 ft. lbs.).
7. Install the intermediate shaft seal to the steering column.

8. Install the transaxle shift cable to the steering column.


9. Connect the steering column electrical connectors.
10. Install the instrument panel left side insulator. Refer to Closeout insulator Panel Replacement - Left in Instrument Panel, Gauges and Wiring
Indicators.
11. Install the steering wheel. Refer to Steering Wheel Replacement.
12. Install the inflatable restraint steering wheel module. Refer to Inflatable Restraint Steering Wheel Module Replacement in Air Bags and Seat
Belts.
13. Enable the SIR system. Refer to Enabling the SIR System in Air Bags and Seat Belts.
14. Connect the battery ground (negative) cable. Refer to Battery Negative Cable Disconnect/Connect Procedure in Starting and Charging.
Steering Column Anchor Cable
Removal Procedure
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 29
Chevrolet Venture V6-3.4L VIN E 313

1. Remove the knee bolster. Refer to Knee Bolster Replacement in Instrument Panel, Gauges and Wiring Indicators.
2. Remove the steering column upper nut.
3. Remove the center console. Refer to Console Replacement - Front Floor in Instrument Panel, Gauges and Wiring Indicators.

4. Remove the anchor cable nut from the center console bracket.
5. Remove the anchor cable.

Installation Procedure

1. Properly route the steering column anchor cable.


2. Install the anchor cable to the center console bracket stud.

Notice: Refer to Fastener Notice in Service Precautions.

3. Install the anchor cable nut to the center console bracket stud.
- Tighten the steering column anchor nut to 10 Nm (114 ft. lbs.).
4. Install the steering column anchor cable end to the steering column stud.
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 30
Chevrolet Venture V6-3.4L VIN E 314

5. Install the steering column nut. Refer to Steering Column Replacement


6. Install the center console. Refer to Console Replacement - Front Floor in Instrument Panel, Gauges and Wiring Indicators.
7. Install the knee bolster. Refer to Knee Bolster Replacement in Instrument Panel, Gauges and Wiring Indicators.

Steering Column Trim Covers


Removal Procedure

Caution: Refer to SIR Handling Caution in Service Precautions.

1. Disable the SIR system. Refer to Disabling the SIR System in Air Bags and Seat Belts.
2. Remove the tilt lever. Refer to Tilt Lever Replacement - On Vehicle.
3. Remove the ignition lock cylinder. Refer to Ignition Lock Cylinder Replacement - On Vehicle (Cylinder Rotates) or Ignition Lock Cylinder
Replacement On Vehicle (Unable to Rotate Cylinder).
4. Remove the steering column trim covers. Refer to Steering Column Trim Covers - Disassemble - Off Vehicle.

Installation Procedure
1. Install the steering column trim covers. Refer to Steering Column Trim Covers - Assemble - Off Vehicle.
2. Install the ignition lock cylinder. Refer to Ignition Lock Cylinder Replacement - On Vehicle (Cylinder Rotates) or Ignition Lock Cylinder
Replacement - On Vehicle (Unable to Rotate Cylinder).
3. Install the tilt lever. Refer to Tilt Lever Replacement - On Vehicle.
4. Enable the SIR system. Refer to Enabling the SIR System in Air Bags and Seat Belts.

Steering Column Trim Covers - Assemble


Assembly Procedure

- Tools Required
- J 41352 Modular Column Holding Fixture

1. Install the shroud protector (1) to the lower shroud (2).


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 31
Chevrolet Venture V6-3.4L VIN E 315

2. Install the upper shroud (2) onto the column.


3. Slide the shift lever seal down the shift lever and install into the upper shrouds (2).

Notice: Refer to Fastener Notice in Service Precautions.

4. Secure the upper shroud (2) using 1 TORX (R) head screw (1).
- Tighten the screw to 1.5 Nm (13 inch lbs.).

5. Install the lower shroud (2) and secure by using 2 pan head tapping screws (1). Adjust the shift lever seal into the shroud.
- Tighten the screws to 3.5 Nm (31 inch lbs.).

6. Take the column out from the J 41352.


7. Remove the top piece of J 41352 from the steering column.
8. Remove J 41352 from the vise.

Steering Column Trim Covers - Disassemble


Disassembly Procedure

- Tools Required
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 32
Chevrolet Venture V6-3.4L VIN E 316
- J 41352 Modular Column Holding Fixture

1. Place the bottom of J 41352 into a vise.


2. Set the steering column in the J 41352.
3. Place the top piece of J 41352 onto the column.
4. Pull the tilt lever out from the lower shroud.

5. Remove 2 pan head tapping screws (2) from the lower shroud (1).
6. Remove the lower shroud (1).

7. Remove 1 TORX (R) head screw (1) from the upper shroud (2).
8. Slide the shift lever seal up the shift lever.
9. Remove the upper shroud (2).
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 33
Chevrolet Venture V6-3.4L VIN E 317

10. Remove the shroud protector (1) from the lower shroud (2).

Steering Shaft, Lower Bearing & Jacket - Assemble


Assembly Procedure

- Tools Required
- J 41688 Centering Sphere Installer Tool

Important: Replace the steering column support assembly (1) if the steering column support assembly (1) has been staked 3 times.

1. Install the steering column support assembly (1) to the jacket assembly.

Notice: Refer to Fastener Notice in Service Precautions.

2. Secure by using 4 TORX (R) screws (2).


- Tighten the screws to 17 Nm (13 ft. lbs.).

3. Lubricate the centering sphere (1) with lithium grease.


4. Install the centering sphere (1) and the joint preload spring (2) into J 41688.
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 34
Chevrolet Venture V6-3.4L VIN E 318

5. Compress the centering sphere and joint preload spring with J 41688.

6. Install the race and upper shaft assembly. Rotate the race and upper shaft assembly 90 degrees and remove with the centering sphere.

7. Remove the race and upper shaft assembly with J 41688.


8. Rotate the race and upper shaft assembly 90 degrees and remove.
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 35
Chevrolet Venture V6-3.4L VIN E 319

9. Apply lithium grease to the race and upper shaft assembly.


10. Install the lower shaft assembly onto the race and upper shaft assembly following the marks from the disassemble procedure.

11. Install the steering shaft assembly (2) into the steering column tilt head assembly (1).

12. Install the tilt head assembly (1) and the lower steering shaft (3) into the steering column jacket assembly (2).

Important: Replace the steering column support assembly if the steering column support assembly has been staked 3 times.
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 36
Chevrolet Venture V6-3.4L VIN E 320

13. Install the 2 pivot pins onto the steering column support assembly.

14. Install the adapter and bearing assembly (1).


15. Install the lower bearing seat (2).
16. Install the lower bearing spring (3).
17. Install the lower spring retainer (4).
18. Install the sensor retainer (5).
19. Install the steering shaft seal (6).
20. Install the linear shift assembly. Refer to Linear Shift Assembly - Assemble - Off Vehicle.
21. Install the turn signal and multifunction switch assembly. Refer to Turn Signal and Multifunction Switch Assembly - Assemble - Off Vehicle.
22. Install the tilt spring. Refer to Tilt Spring - Assemble - Off Vehicle.
Install the lock module assembly. Refer to Electronic Column Lock Module - Assemble - Off Vehicle.

Steering Shaft, Lower Bearing & Jacket - Disassemble


Disassembly Procedure

- Tools Required
- J 21854-1 Pivot Pin Remover
- J 41688 Centering Sphere Installer Tool

1. Remove the lock module assembly. Refer to Electronic Column Lock Module - Disassemble - Off Vehicle.
2. Remove the tilt spring. Refer to Tilt Spring - Disassemble - Off Vehicle.
3. Remove the turn signal and multifunction switch assembly. Refer to Turn Signal and Multifunction Switch Assembly - Disassemble - Off
Vehicle.
4. Remove the linear shift assembly. Refer to Linear Shift Assembly - Disassemble - Off Vehicle.
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 37
Chevrolet Venture V6-3.4L VIN E 321

5. Remove the steering shaft seal (6).


6. Remove the sensor retainer (5).
7. Remove the lower spring retainer (4).

8. Remove the lower bearing spring (3).


9. Remove the lower bearing seat (2).
10. Remove the adapter and bearing assembly (1).
11. Remove 2 pivot pins (3) from the steering column support assembly (1) using the tool J 21854-1.

12. Remove the tilt head assembly (1) from the steering column jacket (2) with the lower steering shaft (3) still attached.
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 38
Chevrolet Venture V6-3.4L VIN E 322

13. Remove the tilt head assembly (1) from the steering shaft assembly (2).

Important: Mark the upper shaft assembly and the lower steering shaft assembly to ensure proper assembly. Failure to assemble properly
will cause the steering wheel to be turned 180 degrees.

14. Tilt the upper shaft assembly (1) 90 degrees to the lower steering shaft assembly (2) and disengage.
Insert the race and upper shaft assembly (1) into J 41688.

16. Insert J 41688 into a vise.


17. Rotate the driver 90 degrees in the counterclockwise direction in order to disengage the centering sphere from the race and upper shaft
assembly.
18. Remove the race and upper shaft assembly (1) from J 41688.
19. Remove the shaft preload spring and the centering sphere from J 41688.
20. If necessary, discard the old centering sphere and the old shaft preload spring.
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 39
Chevrolet Venture V6-3.4L VIN E 323

21. Remove the 4 TORX (R) screws (2) from the steering column support assembly (1).

Steering Wheel
Removal Procedure

- Tools Required
- J 1859-A Steering Wheel Puller
- J 42578 Steering Wheel Puller Legs

1. Turn the ignition OFF.

Caution: Refer to SIR Handling Caution in Service Precautions.

2. Disable the SIR system. Refer to Disabling the SIR System in Air Bags and Seat Belts.

3. Remove the inflator module. Refer to Inflatable Restraint Steering Wheel Module Replacement in Air Bags and Seat Belts.
4. If there are no alignment mark on the steering wheel hub, scribe an alignment mark on the steering wheel hub in line with the mark on the
steering shaft.
5. Loosen the steering wheel nut.
6. Position the steering wheel nut flush with the end of the steering column shaft.
7. Loosen the steering wheel using the following tools.
- For Pontiac vehicles use the J 1859-A and the J 42578.
- For Chevrolet and Oldsmobile vehicles use the J 1859-A.
8. Disconnect the steering wheel controls electrical connector (if equipped).
9. Disconnect the horn switch lead from the steering hub.
10. Remove the steering wheel nut.
11. Remove the steering wheel from the steering shaft.
12. Remove the steering wheel controls and the steering wheel controls harness from the steering wheel (if equipped). Refer to Steering Wheel
Control Switches Replacement (Pontiac) or Steering Wheel Control Switches Replacement (Oldsmobile) in Accessories and Optional
Equipment.

Installation Procedure
1. Install the steering wheel controls and the steering wheel controls harness to the steering wheel (if equipped). Refer to Steering Wheel
Control Switches Replacement (Pontiac) or Steering Wheel Control Switches Replacement (Oldsmobile) in Accessories and Optional
Equipment.
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 40
Chevrolet Venture V6-3.4L VIN E 324

2. Route the SIR connector through the steering wheel.


3. Align the mark on the steering wheel with the mark on the steering shaft.
4. Install the steering wheel.

Notice: Refer to Fastener Notice in Service Precautions.

Important: This is a prevailing torque type fastener. This fastener may be reused ONLY if:
- The fastener and its counterpart are clean and free from rust
- The fastener develops 3 Nm (27 inch lbs.) of torque (drag) against its counterpart prior to the fastener seating.

If the fastener does not meet these criteria, REPLACE the fastener.

5. Install the steering wheel nut.


- Tighten the steering wheel nut to 45 Nm (33 ft. lbs.).
6. Connect the horn switch lead to the steering hub.
7. Connect the steering wheel controls electrical connector (if equipped).
8. Install the inflator module. Refer to Inflatable Restraint Steering Wheel Module Replacement in Air Bags and Seat Belts.
9. Enable the SIR system. Refer to Enabling the SIR System in Air Bags and Seat Belts.
10. Verify that the steering wheel controls operate properly (if equipped).
11. Verify that the horn operates properly.

Turn Signal & Multifunction Switch - Assemble


Assembly Procedure

Important: The electrical contact on the turn signal and multifunction switch assembly must rest on the turn signal cancel cam assembly.

1. Install the turn signal and multifunction switch assembly.

Notice: Refer to Fastener Notice in Service Precautions.


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 41
Chevrolet Venture V6-3.4L VIN E 325

2. Install the 2 pan head tapping screws.


- Tighten the screws to 7 Nm (62 inch lbs.).

3. Slide the 2 connectors (2) of the turn signal and multifunction switch assembly onto the bulk head connector (1).

4. Install the wire harness assembly (4) into the wire harness strap (5).
5. Install the wire harness strap (2) into the steering column tilt head assembly (1).
6. Install the wire harness straps (3) onto the wire harness assembly (4).
7. Install the upper and lower shrouds. Refer to
Steering Column Trim Covers - Assemble -Off Vehicle.

Turn Signal & Multifunction Switch - Disassemble


Disassembly Procedure
1. Remove the upper and lower shrouds. Refer to Steering Column Trim Covers - Disassemble -Off Vehicle.
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 42
Chevrolet Venture V6-3.4L VIN E 326

2. Remove the wire harness assembly (4) from the wire harness strap (5).
3. Remove the wire harness straps (3) from the wire harness assembly (4).
4. Remove 1 wire harness strap (2) from the upper tilt head assembly (1).

5. Slide the 2 connectors of the turn signal and multifunction switch assembly (2) off of the bulk head connector (1).

6. Remove the the 2 pan head tapping screws.


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 43
Chevrolet Venture V6-3.4L VIN E 327

7. Remove the turn signal and multifunction switch assembly.


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 1
Chevrolet Venture V6-3.4L VIN E 328
Spark Plug: Application and ID
Spark Plug ............................................................................................................................................................................................ AC Type 41-940
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 1
Chevrolet Venture V6-3.4L VIN E 329
Spark Plug: Description and Operation

Extended Life Spark Plug (Typical)

Resistor type, tapered seat spark plugs are used on all engines. No gasket is used on these tapered seat plugs. When replacing spark plugs, use only
the type specified. Normal service is assumed to be a mixture of idling, slow speed, and high-speed driving. Occasional intermittent high-speed
driving is needed for good spark plug performance. Intermittent high-speed driving gives increased combustion heat, burning away carbon or
oxides that have built up from frequent idling, or continual stop-and-go driving.

Spark plugs are protected by insulating boots made of special heat-resistant materials, which cover the spark plug terminal and extend downward
over a portion of the plug insulator. These boots prevent flash-over, which causes engine misfiring. Do not mistake corona discharge for flash-over,
or a shorted insulator. Corona is a steady blue light appearing around the insulator, just above the shell crimp. It is the visible evidence of a
high-tension field and has no effect on ignition performance. Usually it can be detected only in darkness. This discharge may repel dust particles,
leaving a clear ring on the insulator just above the shell. This ring is sometimes mistakenly regarded as evidence that combustion gases have blown
out between the shell and the insulator.
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 1
Chevrolet Venture V6-3.4L VIN E 330
Spark Plug: Testing and Inspection
Follow the scheduled maintenance services recommendations to assure satisfactory spark plug performance. Refer to Maintenance Schedule in
Maintenance and Lubrication. Normal spark plug operation will result in brown to grayish-tan deposits appearing on the portion of the spark plug
that projects into the combustion chamber. A small amount of red-brown, yellow, and white powdery material may also be present on the insulator
tip around the center electrode. These deposits are normal combustion by-products of fuels and lubricating oils with additives. Some electrode wear
will also occur.

Engines which are not running properly are often referred to as misfiring. Spark plug misfiring can be indicated in a number of ways:
^ Poor fuel economy
^ Power loss Loss of speed
^ Hard starting
^ Poor engine performance

For information on misfiring, refer to Symptoms in Computers and Control Systems.

Flashover occurs when a damaged spark plug boot, along with dirt and moisture, permits the high voltage charge to short over the insulator to the
spark plug shell or the engine. Should misfiring occur before the recommended replacement interval, locate and correct the cause.

Carbon fouling of the spark plug is indicated by dry, black carbon (soot) deposits on the portion of the spark plug in the cylinder. Excessive idling
or slow speeds under light engine loads can keep the spark plug temperatures so low that these deposits are not burned off. Rich fuel mixtures or
poor ignition system output may also be the cause; refer to Symptoms in Computers and Control Systems 3.4L.

Oil fouling of the spark plug is indicated by wet oily deposits on the portion of the spark plug in the cylinder, usually with little electrode wear. This
may be caused by oil getting past worn piston rings or valve seals. This condition also may occur during break-in of new or newly overhauled
engines.
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 2
Chevrolet Venture V6-3.4L VIN E 331

Deposit fouling of the spark plug occurs when the normal red-brown, yellow or white deposits of combustion by-products become sufficient to
cause misfiring. In some cases, these deposits may melt and form a shiny glaze on the insulator around the center electrode. If the fouling is found
in only one or two cylinders, valve stem clearances or intake valve seals may be allowing excess lubricating oil to enter the cylinder, particularly if
the deposits are heavier on the side of the spark plug that was facing the intake valve.

Excessive gap means that the airspace between the center and side electrodes at the bottom of the spark plug is too wide for consistent spark plug
firing. This may be due to improper gap adjustment or to excessive wear of the electrodes. Check of the gap size and compare the gap measurement
to that specified for the vehicle. Refer to Spark Plug Usage. See: Starting and Charging/Testing and Inspection/Initial Inspection and Diagnostic
Overview/Usage Charts/Spark Plug Usage

Excessive gap wear can be an indication of continuous operation at high speeds or with high engine loads, causing the spark plug to run too hot.
Too small of a gap indicates the plug was damaged at the time of installation. Another possible cause is an excessively lean fuel mixture.

Low or high spark plug installation torque or improper seating of the spark plug can result in the spark plug running too hot and cause excessive
gap wear. The spark plug and cylinder head seats must be in good contact for proper heat transfer and spark plug cooling. Dirty or damaged threads
in the head or on the spark plug can keep the spark plug from seating even though the proper torque is applied. Once the spark plugs are properly
seated, tighten the spark plug to the proper torque. Refer to Spark Plug Usage. See: Starting and Charging/Testing and Inspection/Initial Inspection
and Diagnostic Overview/Usage Charts/Spark Plug Usage

Low torque may result in poor contact of seats due to a loose spark plug. Overtightening may cause the spark plug shell to be stretched and also
result in poor contact between seats. In extreme cases, exhaust blow-by and damage beyond simple gap wear may occur.
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 3
Chevrolet Venture V6-3.4L VIN E 332

Cracked or broken insulators may be the result of improper installation, damage during spark plug regapping, or heat shock to the insulator
material. Upper insulators can be broken when a poorly fitting tool is used during installation or removal, or when the spark plug is hit from the
outside. Cracks in the upper insulator may be inside the shell and not visible. Also, the breakage may not cause problems until oil or moisture
penetrates the crack later.

A broken or cracked lower insulator tip (around the center electrode) can result from damage during regapping or from heat shock ( spark plug
suddenly operating too hot).

Damage during regapping can happen if the gapping tool is pushed against the center electrode or the insulator around it, causing the insulator to
crack. When regapping a spark plug, make the adjustment by only bending the side electrode. Do not contact the other parts of the spark plug.

Heat shock breakage in the lower insulator tip generally occurs during severe engine operating conditions (high-speeds or heavy-loading) and may
be caused by over advanced timing or low grade fuels. Heat shock refers to a rapid increase in the tip temperature that causes the insulator material
to crack.

Spark plugs with less than the recommended amount of service can sometimes be cleaned and regapped, then returned to service. However, if there
is any doubt about the serviceability of a spark plug, replace it. Replace spark plugs with cracked or broken insulators. In some cases, such as
flashover, the ignition wire may need to be replaced.
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 1
Chevrolet Venture V6-3.4L VIN E 333
Spark Plug: Service and Repair
SPARK PLUG REMOVAL PROCEDURE

NOTE: Observe the following Service Precautions:


^ Allow the engine to cool before removing the spark plugs. Attempting to remove spark plugs from a hot engine can cause the spark plugs to
seize. This can damage the cylinder head threads.
^ Clean the spark plug recess area before removing the spark plug. Failure to do so can result in engine damage due to dirt or foreign material
entering the cylinder head, or in contamination of the cylinder head threads. Contaminated threads may prevent proper seating of the new
spark plug.
^ Use only the spark plugs specified for use in the vehicle. Do not install spark plugs that are either hotter or colder than those specified for the
vehicle. Installing spark plugs of another type can severely damage the engine.

1. Turn the ignition OFF.


2. If you are replacing the engine right bank (rear) spark plugs, perform the following steps:
2.1. Remove the windshield wiper module cover.
2.2. Rotate the engine for service access.

ROTATING THE ENGINE FOR SERVICE ACCESS.

^ Tools Required
- J 41131 Engine Tilt Strap

1. Remove the throttle body air inlet duct. See: Fuel Delivery and Air Induction/Air Cleaner Housing/Air Filter Element/Service and Repair
2. Set the park brake.
3. Shift the transaxle into Neutral.
4. Remove the engine mount strut bolts. Swing the engine mount struts aside. Refer to Engine Mount Strut Replacement (Left) or Engine Mount
Strut Replacement (Right).

5. Install the J 41131.


6. Pull on the engine in order to rotate the engine forward.
7. Tighten the J 41131.

3. Remove the spark plug wire(s) from the spark plug(s).


4. Remove the spark plug(s) from the engine.
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 2
Chevrolet Venture V6-3.4L VIN E 334

SPARK PLUG INSTALLATION PROCEDURE

NOTE: It is important to check the gap of all new and reconditioned spark plugs before installation. Pre-set gaps may have changed during
handling. Use a round wire feeler gauge to be sure of an accurate check, particularly on used plugs. Installing plugs with the wrong gap can cause
poor engine performance and may even damage the engine.

1. Gap the spark plug(s) to the specifications.

NOTE: Be sure plug threads smoothly into cylinder head and is fully seated. Use a thread chaser if necessary to clean threads in cylinder
head. Cross-threading or failing to fully seat spark plug can cause overheating of plug, exhaust blow-by, or thread damage. Follow the
recommended torque specifications carefully. Over or under-tightening can also cause severe damage to engine or spark plug.

2. Install the spark plug(s) to the engine.

Tighten
Tighten the spark plug(s)
Initial Installation: 20 Nm (15 lb ft)
Reinstallation: 15 Nm (11 lb ft)

3. Install the spark plug wire(s) to the spark plug(s).


4. If you are replacing the engine right bank (rear) spark plugs, perform the following steps:
4.1. Return the engine to the proper position.
4.2. Install the windshield wiper module cover.
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 1
Chevrolet Venture V6-3.4L VIN E 335
Fuel Delivery and Air Induction: Description and Operation
Fuel System
SYSTEM DESCRIPTION
The fuel pump fuse provides system voltage to the fuel pump relay. The PCM grounds the Fuel Pump Relay control circuit to energize the fuel
pump relay. When the ignition is turned ON, the PCM commands the fuel pump relay ON for at least 2 seconds, voltage is applied to the electric
fuel pump and will continue to energizes the fuel pump after the PCM receives 3X reference pulses. The fuel pump is an electric pump and is
part of the Modular Fuel Sender Assembly. The fuel pump supplies fuel through an in-line fuel filter, fuel rail assembly to the fuel injectors. A
fuel pressure regulator, attached to the fuel rail assembly, maintains a regulated fuel pressure for correct operation of the fuel injectors. Any
unused fuel is then returned to the fuel tank by a separate fuel return pipe.
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 1
Chevrolet Venture V6-3.4L VIN E 336
Fuel Delivery and Air Induction: Description and Operation
Fuel Supply Components

System Overview
The fuel tank stores the fuel supply. An electric fuel pump, located in the fuel tank within the modular fuel sender assembly, pumps fuel through an
in-line fuel filter to the fuel rail assembly. The pump provides fuel pressure greater than is needed by the injectors. The fuel pressure regulator
keeps fuel available to the injectors at a regulated pressure. A separate fuel pipe is used to return fuel to the fuel tank.
Fuel Level Sensor

Fuel Level Sensor

The fuel sensor consists of the following components: float, the wire float arm, and the ceramic resistor card. The fuel level sensor is mounted on
the modular fuel sender Assembly and is used as an input to the PCM. The PCM uses this information as a fuel level input for various diagnosis. In
addition the PCM transmits the fuel level over the Class 2 communication circuit to the IP cluster. This information is used for the IP gauge, and
low fuel warning indicator if applicable.
Fuel Pressure Regulator Assembly
The fuel pressure regulator attaches to the fuel rail on the fuel return side. The fuel pressure is a diaphragm operated relief valve and is referenced
to manifold vacuum. If the fuel pressure is too low, poor performance could result. If the pressure is to high, excessive odor and a Diagnostic
Trouble Code (DTC) may result.

Fuel Pipe O-Rings


Fuel feed and return pipe threaded connections at the fuel rail and fuel filter are sealed with replaceable O-ring seals. These O-rings seals are made
of special material, and should only be serviced with the correct service part.

Fuel Pump Strainer

The fuel pump strainer attaches to the lower end of the modular fuel sender assembly. The fuel pump strainer is made of woven plastic. The
functions of the fuel pump strainer is to filter contaminants and to wick fuel. The life of the fuel pump strainer is generally considered to be that of
the fuel pump, is self-cleaning and normally requires no maintenance. Fuel stoppage at this point indicates that the fuel tank contains an abnormal
amount of sediment or water, in which case the tank should be thoroughly cleaned and replace the plugged fuel pump strainer with a new one.
Fuel Tank Pressure Sensor
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 2
Chevrolet Venture V6-3.4L VIN E 337

Fuel Tank Pressure Sensor

The Fuel Tank Pressure (FTP) Sensor measures the difference between the air pressure (or vacuum) in the fuel tank and the outside air pressure.
The sensor mounts at the top of the fuel tank sending unit. The PCM supplies a 5 volt reference voltage and ground to the sensor. The sensor
provides a signal voltage between 0.1-4.9 voltsto the PCM. When the air pressure in the fuel tank is equal to the outside air pressure, such as when
the fuel fill cap is removed, the output voltage of the sensor will measure 1.3-1.7 volts.

When the air pressure in the tank is 4.5 inches H2O (1.25 kpa), the sensor output voltage should measure 0.5 ± 0.2 volts (1.25 kPa).

The sensor voltage increases to approximately 4.5 volts at 14 inches of H2O (-3.75 kPa).

In-Pipe Fuel Filter

In-Pipe Fuel Filter

The fuel feed pipe has a steel fuel filter installed ahead of the fuel injection system. The paper filter element (2) traps particles in the fuel that may
damage the injection system. The filter housing (1) is made to withstand maximum fuel system pressure, exposure to fuel additives, and changes in
temperature. The fuel filter has a quick-connect inlet fitting and a threaded outlet fitting. The threaded fitting is sealed with an O-ring. There is no
service interval for fuel filter replacement. Replace a restricted fuel filter.
Fuel Tank

Fuel Tank

The fuel tank (1) is located midway on the left inside of the vehicle and is used to store the fuel supply. The fuel tank is molded from high density
polyethylene and is held in place by three metal straps that secure it to the vehicle. The fuel tank shape includes a reservoir in order to maintain a
constant supply of fuel around the fuel pump strainer during low fuel conditions and aggressive vehicle maneuvers. A fuel tank filler pipe
check-valve tube is attached to the fuel tank and extends from the fuel tank inlet to the reservoir. The fuel tank filler pipe check-valve is located
inside the fuel tank filler pipe check-valve tube and prevents fuel from splashing back out of the fuel tank filler pipe during refueling.
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 3
Chevrolet Venture V6-3.4L VIN E 338

The tank also contains a fuel vapor vent valve with roll-over protection. The vent valve also features a two phase vent calibration which increases
fuel vapor flow to the canister when operating temperatures increase the tank pressure beyond an established threshold.

The fuel tank contains several rollover valves that prevents fuel from entering the fuel pipes in the event of a vehicle rollover. The rollover valves
are not repairable.
Fuel Tank Filler Pipe

Fuel Tank Filler Pipe

In order to prevent refueling with leaded fuel, the fuel tank filler pipe (2) has a built-in restrictor and deflector. The fuel tank filler pipe is connected
to the fuel tank filler extension (1) by clamps.

Fuel Tank Filler Pipe Cap


NOTE: Use a fuel tank filler pipe cap with the same features when a replacement is necessary. Failure to use the correct fuel tank filler pipe cap
can result in a serious malfunction of the fuel system.

Fuel Tank Filler Pipe Cap

The fuel tank filler pipe is equipped with a screw type fuel tank filler pipe cap. A built-in torque-limiting device prevents over tightening of the fuel
tank filler pipe cap. In order to install the fuel tank filler pipe cap, turn the fuel tank filler pipe cap clockwise until a clicking noises is heard. The
clicking noises signal that the correct torque has been reached and that the fuel tank filler pipe cap is fully seated. A fuel filler cap that is not fully
seated, may cause a malfunction in the emission system.

The Enhanced EVAP fuel tank pipe cap has a tether connected to the fuel filler door.
Modular Fuel Sender Assembly
The modular fuel sender assembly is attached to the top of the fuel tank, and extends from the top of the fuel tank to the reservoir.
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 4
Chevrolet Venture V6-3.4L VIN E 339

Fuel Level Sensor

The modular fuel sender assembly consists of the following major components: fuel pump, a fuel sender strainer (3), a fuel pump strainer, a
roll-over valve (2), fuel level sensor (4), and a fuel tank pressure sensor.
Nylon Fuel Pipes
CAUTION: In order to Reduce the Risk of Fire and Personal Injury:
^ If nylon fuel pipes are nicked, scratched or damaged during installation, Do Not attempt to repair the sections of the nylon fuel pipes.
Replace them.
^ When installing new fuel pipes, Do Not hammer directly on the fuel harness body clips as it may damage the nylon pipes resulting in
a possible fuel leak.
^ Always cover nylon vapor pipes with a wet towel before using a torch near them. Also, never expose the vehicle to temperatures
higher than 115°C (239°F) for more than one hour, or more than 90°C (194°F) for any extended period.
^ Before connecting fuel pipe fittings, always apply a few drops of clean engine oil to the male pipe ends. This will ensure proper
reconnection and prevent a possible fuel leak. (During normal operation, the O-rings located in the female connector will swell and
may prevent proper reconnection if not lubricated.)

Nylon fuel pipes are designed to perform the same job as the steel or rubber fuel lines they replace. Nylon pipes are constructed to withstand
maximum fuel system pressure, exposure to fuel additives and changes in temperature. There are two sizes used: 3/8" ID for the fuel feed, and
5/16" ID for the fuel return and are used on the modular sender. Nylon fuel pipes are somewhat flexible and can be formed around gradual turns.
However, if forced into sharp bends, nylon pipes will kink and restrict fuel flow. Also, once exposed to fuel, nylon pipes may become stiffer and
are more likely to kink if bent too far. Special care should be taken when working on a vehicle with nylon pipes.
Quick Connect Fittings
Quick-connect type fittings provide a simplified means of installing and connecting fuel system components. Depending on the vehicle model, there
are two types of quick-connect fittings, each used at different locations in the fuel system. Each type of quick-connect fitting consists of a unique
female connector and a compatible male fuel pipe end. O-rings, located inside the female connector, provide the fuel seal. Integral locking tabs or
fingers hold the quick-connect fittings together.
Fuel Feed and Fuel Return Pipes
The fuel feed and fuel return pipes carry fuel from the modular fuel sender assembly to the fuel injection system and back to the modular fuel
sender assembly.
Fuel Pump

The fuel pump is mounted in the fuel reservoir within the modular fuel sender. The fuel pump is an electric high pressure pump. The fuel is pumped
to the fuel rail at a specified flow and pressure. Excess fuel returns to the fuel tank by a return pipe. The fuel pump delivers a constant flow of fuel
to the engine even during low fuel conditions and aggressive vehicle maneuvers. The electric fuel pump operation is controlled by the Powertrain
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 5
Chevrolet Venture V6-3.4L VIN E 340
Control Module (PCM) through a fuel pump relay. The fuel pump flex pipe acts to dampen the fuel pulses and noise generated by the fuel pump.
The fuel pump is serviced as part of the modular fuel sender.
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 1
Chevrolet Venture V6-3.4L VIN E 341
Fuel Delivery and Air Induction: Description and Operation
Fuel Metering

Purpose
The basic function of the air/fuel metering system is to control air/fuel delivery to the engine. The best air/fuel mixture to minimize exhaust
emissions is 14.7 to 1, which allows the catalytic converter to operate most efficiently. Fuel is delivered to the engine by individual fuel injectors
mounted in the intake manifold near each intake valve. The main control sensor is the Heated Oxygen Sensor (HO2S), located in the exhaust
manifold. The HO2S tells the Powertrain Control Module (PCM) how much oxygen is in the exhaust gas and the PCM changes the air/fuel ratio to
the engine by controlling the fuel injector on time. Because of the constant measuring and adjusting of the air/fuel ratio, the fuel injection system is
called a Closed Loop system.
Modes of Operation
The PCM monitors voltages from several sensors to determine the engine's fuel needs. Fuel is delivered under one of several conditions called
modes. All modes are controlled by the PCM and are described below.
Battery Voltage Correction Mode
When battery voltage is low, the PCM will compensate for the weak spark by:
^ Increasing the amount of fuel delivered.
^ Increasing the idle RPM.
^ Increasing ignition dwell time.
Catalytic Converter Protection Mode
The PCM constantly monitors engine operation and estimates conditions that could result in high catalytic converter temperatures. If the PCM
determines the catalytic converter may overheat, it causes the system to return to Open Loop operation and enriches the fuel mixture.
Clear Flood Mode
If the engine floods, clear it by pushing the accelerator pedal down all the way and then crank the engine. The PCM then de-energizes the fuel
injectors. The PCM holds the fuel injectors de-energized as long as the throttle remains above 80 percent and the engine speed is below 600-800
RPM. If the throttle position becomes less than 80 percent, the PCM again begins to pulse the fuel injectors ON and OFF, allowing fuel into the
cylinders.
Deceleration Mode
The PCM reduces the amount of fuel injected when it detects a decrease in throttle position and air flow. When deceleration is very fast, the PCM
may cut off fuel completely for short periods.
Fuel Cut Off Mode
The PCM has the ability to shut OFF the fuel injectors completely or selectively when certain conditions are met. This fuel shut off mode allows the
powertrain to protect itself from damage and also improve its driveability.

The PCM Will Disable the Injectors Under the Following Conditions
^ Ignition OFF (prevents engine run-on).
^ Ignition ON but no ignition reference signal (prevents flooding or backfiring).
^ High engine speed (above red line).
^ High vehicle speed (above rated tire speed).
^ Extended high speed closed throttle coastdown (reduce emissions and increases engine braking).
Fuel RPM Cut Off Ranges
IMPORTANT: These RPM cut off ranges may vary according to PCM calibration, axle ratio, tire size, and tire rating.
^ Park and neutral 6000 RPM.
^ Reverse 4000 RPM.
^ Drive 6000 RPM.
Run Mode
The run mode has two conditions called Open Loop and Closed Loop.

When the engine is first started and engine speed is above 400 RPM, the system is in Open Loop operation. In Open Loop the PCM ignores the
signal from the Heated Oxygen Sensor (HO2S), and calculates the air/fuel ratio based on inputs from the TP, ECT, and MAF sensors.

The system remains in Open Loop until the following conditions are met:
1. The HO2S has a varying voltage output showing that it is hot enough to operate properly (this depends on temperature).
2. The ECT has reached a specified temperature.
3. A specific amount of time has elapsed since starting the engine.

The specific values for the above conditions vary with different engines. When these conditions are met, the system enters Closed Loop operation.
In Closed Loop the PCM changes fuel injector on-time based on the signal from the HO2S. This allows the air/fuel ratio to stay very close to 14.7:1
.
Starting Mode
When the ignition is first turned ON the PCM energizes the fuel pump relay for two seconds, allowing the fuel pump to build up pressure. The
PCM then checks the Engine Coolant Temperature (ECT sensor and the Throttle Position (TP) sensor. During cranking, the PCM checks the
crankshaft position signal in order to determine the proper air/fuel ratio for starting. The PCM controls the amount of fuel delivered in the starting
mode by changing how long the fuel injectors are energized. This is done by pulsing the fuel injectors for very short times.
Acceleration Mode
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 2
Chevrolet Venture V6-3.4L VIN E 342
The PCM provides extra fuel when it detects a rapid increase in throttle position and air flow.

Fuel Metering System Components


The fuel metering system is made up of the following parts:
^ The fuel injectors.
^ The throttle body.
^ The fuel rail.
^ The fuel pressure regulator.
^ The PCM.
^ The crankshaft position sensor.
^ The camshaft position sensor.
^ The fuel pump.
^ The fuel pump relay.
Basic System Operation
The fuel metering system starts with the fuel in the fuel tank. An electric fuel pump, located in the fuel tank with the gauge sending unit, pumps fuel
to the fuel rail through an in-pipe fuel filter. The fuel pump is designed to provide fuel at a pressure above the pressure needed by the fuel injectors.
A fuel pressure regulator in the fuel rail keeps fuel available to the fuel injectors at a constant pressure. Unused fuel is returned to the fuel tank by a
separate pipe. For further information on the fuel tank, in-pipe filter, and fuel pipes, Refer to Fuel Supply Component Description.

Accelerator Controls
The accelerator control system is cable-type. There are no linkage adjustments. Therefore, the specific accelerator control cable must be used.
Fuel Injector

The MULTEC 2 MPFI fuel injector assembly is a solenoid operated device, Controlled by an on-board computer called the Powertrain Control
Module (PCM), that meters fuel to a single engine cylinder. The PCM energizes the high-impedance (12.0 ohms) solenoid (2) to open a normally
closed ball valve (3). This allows fuel to flow into the top of the injector (1), past the ball valve, and through a director plate at the injector outlet.
The director plate has precision holes that control fuel flow, generating a spray of finely atomized fuel at the injector tip.

Fuel from the injector tip is directed at the intake valve, causing it to become further atomized and vaporized before entering the combustion
chamber.

The eight digit part number (2) is identified on the fuel injector body (1). A four digit number build date code is located to the far left of the part
number.
Fuel Pressure Regulator
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 3
Chevrolet Venture V6-3.4L VIN E 343

Fuel Pressure Regulator

The fuel pressure regulator is a diaphragm-operated relief valve with fuel pump pressure on one side and manifold pressure on the other. The
function of the fuel pressure regulator is to maintain the fuel pressure available to the fuel injectors at 3 times barometric pressure, adjusted for
engine load.

The fuel pressure regulator is mounted on the fuel rail and may be serviced separately.

If the fuel pressure is too low, poor performance and DTC P0171 could result. If the pressure is too high, excessive odor and/or DTC P0172 may
result. Refer to Fuel System Pressure Test.

Fuel Pump Electrical Circuit


When the key is first turned ON, the PCM energizes the fuel pump relay for two seconds to build up the fuel pressure quickly. If the engine is not
started within two seconds, the PCM shuts the fuel pump OFF and waits until the engine is cranked. When the engine is cranked and the RPM
signal has been detected by the PCM, the PCM supplies 12 volts to the fuel pump relay to energize the electric in-tank fuel pump. An inoperative
fuel pump relay can result in long cranking times, particularly if the engine is cold. An inoperative fuel pump would cause a no start condition. A
fuel pump which does not provide enough pressure can result in poor performance.

Fuel Rail
The fuel rail assembly is made up of the left hand rail (5), which delivers fuel to the even cylinders (2,4,6) the right hand rail (1), which delivers
fuel to the odd cylinders (1,3,5) the fuel injectors (4), and the fuel pressure regulator assembly (3) which are mounted to the lower section of the
intake manifold and distributes fuel to the cylinders through the individual injectors.

Fuel is delivered to the fuel inlet tube (2) of the fuel rail by the fuel pipes. The fuel then goes through the fuel rail to the fuel pressure regulator. The
fuel pressure regulator maintains a constant fuel pressure at the fuel injectors. Remaining fuel is then returned to the fuel tank.
Idle Air Control (IAC) Valve
The purpose of the Idle Air Control (IAC) valve is to control engine idle speed, while preventing stalls due to changes in engine load. The IAC
valve, mounted in the throttle body, controls bypass air around the throttle plate. By moving a conical valve, known as a pintle, in (to decrease air
flow) or out (to increase air flow), a controlled amount of air can move around the throttle plate. If RPM is too low, the PCM will retract the IAC
pintle, resulting in more air being bypassed around the throttle plate to increase RPM. If RPM is too high, the PCM will extend the IAC pintle,
allowing less air to be bypassed around the throttle plate, decreasing RPM.

The IAC pintle moves in small steps called counts.


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 4
Chevrolet Venture V6-3.4L VIN E 344

During idle, the proper position of the IAC pintle is calculated by the PCM based on battery voltage, coolant temperature, engine load, and engine
RPM. If the RPM drops below a specified value, and the throttle plate is closed (TP sensor voltage is between 0.20-0.74), the PCM senses a near
stall condition. The PCM will then calculate a new IAC pintle position to prevent stalls.

If the IAC valve is disconnected and reconnected with the engine running, the idle RPM will be wrong. In this case, the IAC has to be reset.

The IAC resets when the key is cycled ON then OFF.

When servicing the IAC, it should only be disconnected or connected with the ignition OFF in order to keep from having to reset the IAC.

The position of the IAC pintle affects engine start up and the idle characteristics of the vehicle. If the IAC pintle is open fully, too much air will be
allowed into the manifold. This results in high idle speed, along with possible hard starting and a lean air/fuel ratio. DTC P0507 may set. If the IAC
pintle is stuck closed, too little air will be allowed in the manifold. This results in a low idle speed, along with possible hard starting and a rich
air/fuel ratio. DTC P0506 may set. If the IAC pintle is stuck part way open, the idle may be high or low and will not respond to changes in engine
load.
Mass Air Flow (MAF) Sensor
The MAF sensor is attached to the front (air inlet side) of the throttle body and is used to measure the amount of air entering the engine. The PCM
uses this information to determine the operating condition of the engine and to control fuel delivery. For further information, refer to In formation
Sensors/Switches Description.
Throttle Body Unit

The throttle body has a throttle plate to control the amount of air delivered to the engine. The TP sensor (2), and IAC sensor (1) are also mounted
on the throttle body.

Vacuum ports located behind the throttle plate provide the vacuum signals needed by various components.
Throttle Position (TP) Sensor
The nonadjustable TP sensor is mounted on the side of the throttle body opposite the throttle lever. It senses the throttle valve angle and relays that
information to the PCM. Knowledge of the throttle angle is needed by the PCM to generate the required injector control signals (pulse). For further
information, Refer to Information Sensors/Switches Description.
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 1
Chevrolet Venture V6-3.4L VIN E 345
Fuel Delivery and Air Induction: Component Tests and General Diagnostics

Fuel Pump Electrical Circuit Diagnosis

Diagnostic Chart (Part 1 Of 3)


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 2
Chevrolet Venture V6-3.4L VIN E 346

Diagnostic Chart (Part 2 Of 3)


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 3
Chevrolet Venture V6-3.4L VIN E 347

Diagnostic Chart (Part 3 Of 3)

Schematic
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 4
Chevrolet Venture V6-3.4L VIN E 348

CIRCUIT DESCRIPTION
When the ignition switch is first turned on, the PCM energizes the fuel pump relay which applies power to the in-tank fuel pump. The fuel pump
relay will remain on as long as the engine is running or cranking and the PCM is receiving reference pulses. If no reference pulses are present,
the PCM de-energizes the fuel pump relay within 2 seconds after the ignition is turned on or the engine is stopped.

The fuel pump delivers fuel to the fuel rail and injectors, then to the fuel pressure regulator. The fuel pressure regulator controls fuel pressure by
allowing excess fuel to be returned to the fuel tank.

DIAGNOSTIC AIDS
Inspect for the following:

IMPORTANT: Remove any debris from the connector surfaces before servicing a component. Inspect the connector gaskets when diagnosing
or replacing a component. Ensure that the gaskets are installed correctly. The gaskets prevent contaminate intrusion.

- Poor terminal connection-Inspect the harness connectors for backed out terminals, improper mating, broken locks, improperly formed or
damaged terminals, and faulty terminal to wire connection. Use a corresponding mating terminal to test for proper tension. Refer to
Diagrams.
- Damaged harness-Inspect the wiring harness for damage. If the harness inspection does not reveal a problem, observe the display on the scan
tool while moving connectors and wiring harnesses related to the sensor. A change in the scan tool display may indicate the location of the
fault. Refer to Diagrams.
- PCM and engine grounds for clean and secure connections

If the DTC is determined to be intermittent, reviewing the Failure Records can be useful in determining when the DTC was last set.

TEST DESCRIPTION
The numbers below refer to the step numbers on the Diagnostic Table:
2. Command both the ON and OFF states. Repeat the commands as necessary.
3. This step determines if the condition is located on the coil side or the switch side of the circuit.
4. This step verifies that the PCM is providing voltage to the fuel pump relay.
5. This step tests for an open in the fuel pump relay ground circuit.
6. This step determines if a voltage is constantly being applied to the fuel pump relay.
12. This tests for a grounded circuit between the in-line connector and the fuel pump fuse.
15. This step jumps the fuel pump relay in order to activate the fuel pump.
16. This step tests for an open in the fuel pump feed circuit between the in-line connector and the fuel pump relay.
17. This step tests for an open or high resistance in the fuel pump ground circuit.
20. This step determines if the condition with the circuit is intermittent. If the fuse does not open, inspect the supply voltage circuit between the
fuse and the fuel pump for an intermittent condition.

Fuel System Diagnosis

Diagnostic Chart (Part 1 Of 3)


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 5
Chevrolet Venture V6-3.4L VIN E 349

Diagnostic Chart (Part 2 Of 3)


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 6
Chevrolet Venture V6-3.4L VIN E 350

Diagnostic Chart (Part 3 Of 3)

SYSTEM DESCRIPTION
Proper fuel pressure is necessary to maintain efficient engine operation and emission levels, if fuel pressure is not within specifications vehicle
drivability may be affected or emission levels elevated.

The fuel system contains the following components:


- Fuel strainer
- Modular fuel sender assembly
- Fuel filter
- Fuel feed pipes/hoses
- Fuel pressure regulator
- Fuel rail
- Fuel injectors
- Fuel return pipes/hoses

TEST DESCRIPTION
Numbers below refer to the step numbers on the Diagnostic Table.
2. Tests the fuel systems ability to achieve a specific fuel pressure range. It may be necessary to cycle the fuel pump several times to achieve the
pressure range.
6. A fuel system that drops more than 5 psi in 10 minutes has a leak in one or more areas.
8. Tests the fuel systems ability to maintain a specific fuel pressure. It may be necessary to cycle the fuel pump several times to achieve the
pressure range.
9. Fuel pressure that drops-off during acceleration, cruise, or hard cornering may cause a lean condition. A lean condition can cause a loss of
power, surging, or misfire and may be diagnosed using a scan tool. If an extremely lean condition occurs, the oxygen sensors may drop
below 500 mV and the fuel injector pulse width will increase.
13. When the engine is at idle, the manifold pressure is low (high vacuum). This low pressure (high vacuum) is applied to the fuel pressure
regulator diaphragm, the result is lower fuel pressure. The fuel pressure at idle will vary slightly as the pressure changes, but the fuel pressure
at idle should always be less than the fuel pressure noted in Step 2 with the engine OFF.
14. This test determines if the high fuel pressure is due to a restricted fuel return pipe or fuel pressure regulator. A rich condition may cause a
DTC P0132 or DTC P0172 to set. Driveability conditions associated with rich conditions can include hard starting (followed by black
smoke) and a strong sulfur smell in the exhaust.
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 1
Chevrolet Venture V6-3.4L VIN E 351
Fuel Pressure Release: Service and Repair

RELIEF PROCEDURE

TOOLS REQUIRED
^ J34730-1A Fuel Pressure Gauge
^ J 34730-262 Fuel Pressure Gauge Fitting

CAUTION: Refer to Battery Disconnect Caution in Service Precautions.

1. Disconnect the negative battery terminal.

IMPORTANT: Mount the fuel pressure gauge fitting above the belt to avoid contact with the belt.

2. Install the J 34730-262 Fuel Pressure Gauge Fitting adaptor to the fuel pressure connection.
3. Connect Fuel Pressure Gauge J34730-1A to the fuel adaptor pressure fitting. Wrap a shop towel around the fuel pressure connection while
connecting the fuel pressure gauge in order to avoid spillage.
4. Install the bleed hose into an approved container and open the valve to bleed the system pressure. The fuel connections are now safe for
servicing.
5. Drain any fuel remaining in the fuel pressure gauge into an approved container.
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 1
Chevrolet Venture V6-3.4L VIN E 352
Accelerator Pedal: Service and Repair

REMOVAL PROCEDURE
1. Remove the left instrument panel sound insulator.
2. Disconnect the accelerator cable from accelerator pedal.
3. Remove the bolts and studs holding the accelerator pedal to the bulk head.
4. Remove the accelerator pedal.

INSTALLATION PROCEDURE
1. Position the accelerator pedal to the bulkhead.

NOTE: Refer to Fastener Notice in Service Precautions.

2. Install the accelerator pedal bolt and stud.

Tighten
Tighten the bolts and studs to 3.0 N.m (27 lb in).

3. Connect the accelerator cable to accelerator pedal.


4. Inspect for complete throttle opening and closing positions by operating the accelerator pedal. Also inspect the carpet fit under the accelerator
pedal.
5. Install the left instrument panel sound insulator.
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 1
Chevrolet Venture V6-3.4L VIN E 353
Air Cleaner Housing: Service and Repair
REMOVAL PROCEDURE

1. Remove the bolt from the coolant tank.


2. Remove the coolant tank and set aside.
3. Remove the 3 bolts from the support brace and remove the brace.
4. Disconnect the MAF sensor electrical connector.
5. Loosen the 2 clamps on the duct/MAF sensor assembly.
6. Remove the air inlet duct/MAF sensor assembly (1).
7. Unsnap the 2 latches and remove the air cleaner housing cover (2).
8. Remove the air filter element (3).

9. Unsnap the latch on the upper cover and remove the cover.
10. Carefully remove the PCM leaving the 2 harnesses connected and set aside.

11. Remove the 2 bolts (2) from the air cleaner assembly and remove the housing.
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 2
Chevrolet Venture V6-3.4L VIN E 354

INSTALLATION PROCEDURE

1. Position the air cleaner housing on the stud (3).

NOTE: Refer to Fastener Notice in Service Precautions.

2. Install the 2 bolts (1) through the housing.

3. Carefully Install the PCM into the housing.


4. Install the upper cover and snap it in place.

5. Install the air cleaner element (3) and air cleaner cover (2) and snap them in place.
6. Install the air inlet duct/Map sensor assembly (1) and tighten the 2 clamps.
7. Connect the MAF sensor electrical connector.
8. Position the support brace and install the 3 bolts.
9. Install the coolant tank and Install the retaining bolt.
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 1
Chevrolet Venture V6-3.4L VIN E 355
Air Filter Element: Service and Repair

REMOVAL PROCEDURE
1. Disconnect the MAF sensor electrical connector.
2. Loosen the air intake duct/MAF sensor hose clamps.
3. Remove the air intake duct/MAF sensor assembly (1).
4. Unsnap the 2 housing cover retaining clamps.
5. Remove the air cleaner cover (2) and carefully remove the air filter element (3).
6. Inspect the housing cover, seal assembly, and air ducting for damage. If a problem is found, replace as necessary.

INSTALLATION PROCEDURE
1. Carefully install the air filter element (3) into the air cleaner assembly.
2. Install the housing cover (2)and snap the retaining clamps in place.
3. Install the air intake duct/MAF sensor assembly (1).
4. Tighten the air intake duct/MAF sensor hose clamps.
5. Connect the MAF sensor electrical connector.
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 1
Chevrolet Venture V6-3.4L VIN E 356
Mass Air Flow (MAF) Sensor: Service and Repair

REMOVAL PROCEDURE
1. Turn OFF the ignition.
2. Loosen both clamps on the MAF sensor (1).
3. Remove the air inlet duct from the MAF sensor.
4. Remove the MAF sensor from air filter housing.

INSTALLATION PROCEDURE
1. Carefully install MAP sensor (1) to air inlet grommet.
2. Attach the MAF sensor (1) to air inlet duct and install the air inlet duct.
3. Tighten the MAP sensor clamps.
4. Connect the MAP sensor electrical connector.
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 1
Chevrolet Venture V6-3.4L VIN E 357
Fillpipe Restrictor: Description and Operation
Fuel Tank Filler Pipe

Fuel Tank Filler Pipe

In order to prevent refueling with leaded fuel, the fuel tank filler pipe (2) has a built-in restrictor and deflector. The fuel tank filler pipe is connected
to the fuel tank filler extension (1) by clamps.
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 1
Chevrolet Venture V6-3.4L VIN E 358
Fillpipe Restrictor: Description and Operation
Fuel Tank Filler Pipe Cap
NOTE: Use a fuel tank filler pipe cap with the same features when a replacement is necessary. Failure to use the correct fuel tank filler pipe cap
can result in a serious malfunction of the fuel system.

Fuel Tank Filler Pipe Cap

The fuel tank filler pipe is equipped with a screw type fuel tank filler pipe cap. A built-in torque-limiting device prevents over tightening of the fuel
tank filler pipe cap. In order to install the fuel tank filler pipe cap, turn the fuel tank filler pipe cap clockwise until a clicking noises is heard. The
clicking noises signal that the correct torque has been reached and that the fuel tank filler pipe cap is fully seated. A fuel filler cap that is not fully
seated, may cause a malfunction in the emission system.

The Enhanced EVAP fuel tank pipe cap has a tether connected to the fuel filler door.
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 1
Chevrolet Venture V6-3.4L VIN E 359
Fuel Filter: Service and Repair

REMOVAL PROCEDURE

IMPORTANT: There is no service interval for in-pipe fuel filter replacement. Only replace the in-pipe fuel filter if it is restricted.

1. Relieve the fuel system pressure. Refer to Fuel Pressure Relief Procedure.
2. Raise the vehicle. Refer to Lifting and Jacking the Vehicle in Service Precautions.
3. Remove the quick-connect fitting at the inlet of the in-pipe fuel filter.
4. Remove the quick-connect fitting at the outlet of the in-pipe fuel filter.
5. Drain any remaining fuel into an approved gasoline container.
6. Remove the in-pipe fuel filter mounting bracket attaching nut.
7. Remove the in-pipe fuel filter and mounting bracket.
8. Remove the in-pipe fuel filter from the in-pipe fuel filter mounting bracket.

INSTALLATION PROCEDURE
1. Remove the protective caps from the new in-pipe fuel filter.
2. Install the in-pipe fuel filter into the in-pipe fuel filter mounting bracket.
3. Install the in-pipe fuel filter and mounting bracket.

NOTE: Refer to Fastener Notice in Service Precautions.

4. Reinstall the in-pipe fuel filter mounting bracket attaching nut.

Tighten
Tighten the nut to 10 N.m (89 lb in).

5. Connect the quick-connect fitting at the inlet of the in-pipe fuel filter.
6. Connect the quick-connect fitting at the outlet of the in-pipe fuel filter.
7. Lower the vehicle.
8. Tighten the fuel fill cap.
9. Reconnect the negative battery cable.
10. Inspect for fuel leaks.
10.1. Turn the ignition switch ON for 2 seconds.
10.2. Turn the ignition switch OFF for 10 seconds.
10.3. Turn the ignition switch ON.
10.4. Check for fuel leaks.
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 1
Chevrolet Venture V6-3.4L VIN E 360
Fuel Filter: Description and Operation

In-Pipe Fuel Filter

The fuel feed pipe has a steel fuel filter installed ahead of the fuel injection system. The paper filter element (2) traps particles in the fuel that may
damage the injection system. The filter housing (1) is made to withstand maximum fuel system pressure, exposure to fuel additives, and changes in
temperature. The fuel filter has a quick-connect inlet fitting and a threaded outlet fitting. The threaded fitting is sealed with an O-ring. There is no
service interval for fuel filter replacement. Replace a restricted fuel filter.
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 1
Chevrolet Venture V6-3.4L VIN E 361
Fuel Injector: Description and Operation

The MULTEC 2 MPFI fuel injector assembly is a solenoid operated device, Controlled by an on-board computer called the Powertrain Control
Module (PCM), that meters fuel to a single engine cylinder. The PCM energizes the high-impedance (12.0 ohms) solenoid (2) to open a normally
closed ball valve (3). This allows fuel to flow into the top of the injector (1), past the ball valve, and through a director plate at the injector outlet.
The director plate has precision holes that control fuel flow, generating a spray of finely atomized fuel at the injector tip.

Fuel from the injector tip is directed at the intake valve, causing it to become further atomized and vaporized before entering the combustion
chamber.

The eight digit part number (2) is identified on the fuel injector body (1). A four digit number build date code is located to the far left of the part
number.
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 1
Chevrolet Venture V6-3.4L VIN E 362
Fuel Injector: Service and Repair

REMOVAL PROCEDURE

NOTE: Use care in removing the fuel injectors in order to prevent damage to the fuel injector electrical connector pins or the fuel injector
nozzles. Do not - immerse the fuel injector in any type of cleaner. The fuel injector is an electrical component and may be damaged by this
cleaning method.

IMPORTANT: Important the fuel injector is serviced as a complete assembly only. If the fuel injectors are found to be leaking, the engine oil
may be contaminated with fuel.

1. Relieve fuel system pressure. Refer to Fuel Pressure Relief Procedure.


2. Remove the fuel rail.
3. Remove the fuel injector retaining clips (1).
4. Remove the fuel injectors (3) from the fuel rail.
5. Remove the fuel injector Upper O-ring (2).
6. Remove the fuel injector lower O-ring (4).

INSTALLATION PROCEDURE

IMPORTANT: Important each fuel injector is calibrated for a specific flow rate. Be sure to use the correct part number when ordering
replacement fuel injectors. When replacing the fuel injector O-rings, be sure to install the brown O-ring in the lower position. The fuel injector
lower O-ring uses a nylon collar, called the O-ring backup, to properly position the O-ring on the fuel injector. Be sure to Install the O-ring
backup, or the sealing O-ring may move on the fuel injector when installing the fuel rail. If the sealing O-ring is not seated properly, a vacuum
leak is possible and driveability complaints may occur.

1. Install the fuel injector upper O-ring (2).


2. Install the fuel injector lower O-ring (4).
3. Install the fuel injector (3) to the fuel rail.
4. Install the fuel injector retaining clips (1).
5. Install the fuel rail.

CAUTION: Refer to Battery Disconnect Caution in Service Precautions.

6. Connect the negative battery cable.


7. Inspect for fuel leaks using the following procedure:
7.1. Turn ON the ignition, for 2 seconds.
7.2. Turn OFF the ignition, for 10 seconds.
7.3. Turn ON the ignition.
7.4. Inspect for fuel leaks.
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 1
Chevrolet Venture V6-3.4L VIN E 363
Fuel Line Coupler: Service and Repair
Metal Collar
REMOVAL PROCEDURE

TOOLS REQUIRED
J 37088-A Fuel Line Quick-Connect Separator

CAUTION:
^ Wear safety glasses when using compressed air, as flying dirt particles may cause eye injury.
^ Relieve the fuel system pressure before servicing fuel system components in order to reduce the risk of fire and personal injury.

After relieving the system pressure, a small amount of fuel may be released when servicing the fuel lines or connections. In order to
reduce the chance of personal injury, cover the regulator and the fuel line fittings with a shop towel before disconnecting. This will
catch any fuel that may leak out. Place the towel in an approved container when the disconnection is complete.

NOTE:
^ Before attempting any On-Vehicle Service, place a dry chemical (Class B) fire extinguisher near work area.
^ Cap the fittings and plug the holes when servicing the fuel system in order to prevent dirt and other contaminants from entering the open
pipes and passages.

IMPORTANT: Always maintain cleanliness when servicing fuel system components.

1. Relieve the fuel system pressure. Refer to Fuel Pressure Relief Procedure.
2. Grasp both sides of the fitting. Twist the female connector 1/4 turn in each direction to loosen any dirt within the fitting.

3. Used compressed air in order to blow any dirt out of the fining.

4. Choose the correct tool from J 37088-A Tool Set for the size of the fitting. Insert the tool into the female connector and push inward in order
to release the locking tabs.
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 2
Chevrolet Venture V6-3.4L VIN E 364

5. Pull the connection apart.

NOTE: If necessary, remove rust or burrs from the fuel pipes with an emery cloth. Use a radial motion with the fuel pipe end in order to prevent
damage to the O-ring sealing surface. Use a clean shop towel in order to wipe off the male tube ends. Inspect all the connections for dirt and
burrs. Clean or replace the components and assemblies as required.

6. Use a clean shop towel in order to wipe off the male pipe end.
7. Inspect both ends of the fitting for dirt and burrs. Clean or replace the components as required.

INSTALLATION PROCEDURE

CAUTION: In order to reduce the risk of fire and personal injury, before connecting fuel pipe fittings, always apply a few drops of
clean engine oil to the male pipe ends.

This will ensure proper reconnection and prevent a possible fuel leak.

During normal operation, the O-rings located in the female connector will swell and may prevent proper reconnection if not lubricated.

1. Apply a few drops of clean engine oil to the male pipe end.

2. Push both sides of the fitting together in order to snap the retaining tabs into place.

3. Once installed, pull on both sides of the fitting in order to ensure the connection is secure.
4. Tighten the fuel filler cap.
5. Reconnect the negative battery cable.
6. Inspect for leaks.
6.1. Turn the ignition switch ON for 2 seconds.
6.2. Turn the ignition switch OFF for 10 seconds.
6.3. Turn the ignition switch ON.
6.4. Inspect for fuel leaks.
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 1
Chevrolet Venture V6-3.4L VIN E 365
Fuel Line Coupler: Service and Repair
Plastic Collar
REMOVAL PROCEDURE

CAUTION:
^ Relieve the fuel system pressure before servicing fuel system components in order to reduce the risk of fire and personal injury.

After relieving the system pressure, a small amount of fuel may be released when servicing the fuel lines or connections. In order to
reduce the chance of personal injury, cover the regulator and the fuel line fittings with a shop towel before disconnecting. This will
catch any fuel that may leak out. Place the towel in an approved container when the disconnection is complete.

^ Wear safety glasses when using compressed air, as flying dirt particles may cause eye injury.

NOTE:
^ Before attempting any On-Vehicle Service, place a dry chemical (Class B) fire extinguisher near work area.
^ Cap the fittings and plug the holes when servicing the fuel system in order to prevent dirt and other contaminants from entering the open
pipes and passages.

IMPORTANT: Always maintain cleanliness when servicing fuel system components.

1. Relieve the fuel system pressure. Refer to Fuel Pressure Relief Procedure.
2. Grasp both sides of the quick-connect fitting. Twist the quick-connect fitting 1/4 turn in each direction in order to loosen any dirt within the
fitting.
3. Repeat the procedure for the other fuel pipe fitting.

4. Use compressed air at both ends of the fitting in order to blow any dirt from the quick-connect fittings.

5. Squeeze the plastic tabs on the male end connector.

6. Pull the connection apart. Repeat the procedure for the other fitting.
7. Use a clean shop towel in order to wipe off the male pipe end.
8. Clean or replace the components/assemblies as required.
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 2
Chevrolet Venture V6-3.4L VIN E 366

INSTALLATION PROCEDURE

CAUTION: In order to reduce the risk of fire and personal injury, before connecting fuel pipe fittings, always apply a few drops of
clean engine oil to the male pipe ends.

This will ensure proper reconnection and prevent a possible fuel leak.

During normal operation, the O-rings located in the female connector will swell and may prevent proper reconnection if not lubricated.

1. Apply a few drops of clean oil to the male pipe end.

2. Push both sides of the quick-connect fitting together in order to cause the retaining tabs/fingers to make sure snap into place.

3. Pull on both sides of the quick connect fitting in order to make sure the connection is secure.
4. Tighten the fuel filler cap.
5. Reconnect negative battery cable.
6. Inspect for fuel leaks.
6.1. Turn the ignition switch ON for 2 seconds.
6.2. Turn the ignition switch OFF for 10 seconds.
6.3. Turn the ignition switch ON.
6.4. Check for leaks.
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 1
Chevrolet Venture V6-3.4L VIN E 367
Fuel Pressure Regulator: Service and Repair

REMOVAL PROCEDURE
1. Relieve fuel system pressure. Refer to Fuel Pressure Relief Procedure.
2. Disconnect the fuel pressure regulator vacuum line.
3. Remove the fuel pressure regulator retaining screw.
4. Using a shop towel to catch any spilled fuel, lift and twist the fuel pressure regulator in order to remove the fuel pressure regulator from the
fuel rail.
5. Remove the retainer and spacer bracket from rail and discard.
6. Remove the fuel pressure regulator from the engine fuel return pipe.
7. Remove the fuel pressure regulator inlet O-ring and discard.

INSTALLATION PROCEDURE

CAUTION: Connect the fuel return line before tightening the regulator attaching screw in order to prevent the regulator from rotating.
Rotation of the regulator could damage the retainer and spacer bracket and lead to a fuel leak at the regulator inlet.

NOTE
^ Do not use compressed air in order to test or clean a fuel pressure regulator as damage to the fuel pressure regulator may result.
^ Clean the fuel pressure regulator filter screen with gasoline if necessary.
^ Do not immerse the fuel pressure regulator in a solvent bath in order to prevent damage to the fuel pressure regulator.

1. Check the filter screen for contamination. If contaminated, replace the fuel pressure regulator.
2. Lubricate new pressure regulator inlet O-ring with clean engine oil and install on regulator inlet.
3. Install the fuel return pipe to regulator.
4. Install the new retainer and spacer bracket into slot on fuel rail.
5. Install the pressure regulator to fuel rail.

Tighten
Tighten engine fuel return pipe nut to 17 N.m (13 lb ft).

6. Connect the fuel pressure regulator vacuum line.

NOTE: Refer to Fastener Notice in Service Precautions.

7. Install the pressure regulator attaching screw.

Tighten
Tighten pressure regulator attaching screw to 8.5 N.m (76 lb in).

8. Tighten the pressure regulator fuel return pipe nut.

Tighten
Tighten fuel return pipe nut to 17 N.m (13 lb ft).

9. Inspect and verity that retainer and spacer bracket is engaged in slots in fuel rail. Grasp and pull on regulator to ensure that it is properly
seated.
10. Install the fuel filler cap.
11. Inspect for fuel leaks using the following procedure:
11.1. Turn ON the ignition, for 2 seconds.
11.2. Turn OFF the ignition, for 10 seconds.
11.3. Turn ON the ignition.
11.4. Inspect for fuel leaks.
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 1
Chevrolet Venture V6-3.4L VIN E 368
Fuel Pump Pickup Filter: Service and Repair
REMOVAL PROCEDURE

IMPORTANT: Always maintain cleanliness when servicing fuel system components.

Fuel Sender Assembly

1. Relieve fuel system pressure. Refer to Fuel Pressure Relief Procedure.


2. Remove the fuel sender assembly.

3. Support the reservoir with one hand and grasp the strainer with the other hand.
4. Use a screwdriver to pry the strainer ferrule off the reservoir.
5. Discard the strainer.

INSTALLATION PROCEDURE

1. Install the new strainer (4) to the reservoir.


2. Support the reservoir with one hand and grasp the strainer with the other hand twisting the strainer into position.
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 2
Chevrolet Venture V6-3.4L VIN E 369
3. Install the fuel sender assembly.
4. Inspect for fuel leaks using the following procedure:
4.1. Turn ON the ignition, for 2 seconds.
4.2. Turn OFF the ignition, for 10 seconds.
4.3. Turn ON the ignition.
4.4. Inspect for fuel leaks.
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 1
Chevrolet Venture V6-3.4L VIN E 370
Fuel Rail: Service and Repair
REMOVAL PROCEDURE

An eight digit identification number is stamped on the left hand fuel rail (fueling even cylinders 2,4,6). Refer to this number it servicing or part
replacement is required.

CAUTION: In order to reduce the risk of fire and personal injury that may result from a fuel leak, always install the fuel injector
O-rings in the proper position. If the upper and lower O-rings are different colors (black and brown), be sure to install the black O-ring
in the upper position and the brown O-ring in the lower position on the fuel injector. The O-rings are the same size but are made of
different materials.

IMPORTANT: Important when servicing the fuel rail assembly, precautions must be taken to prevent dirt and other contaminants from entering
the fuel passages. It is recommended that the fittings be capped, and the holes be plugged during servicing.

1. Relieve fuel system pressure. Refer to Fuel Pressure Relief Procedure.


2. Remove the upper intake manifold.
3. Disconnect the engine fuel feed pipe at fuel rail.

4. Disconnect the engine fuel return pipe at the fuel pressure regulator.
5. Remove the fuel feed pipe and fuel return pipe O-rings and discard.
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 2
Chevrolet Venture V6-3.4L VIN E 371

6. Disconnect the main injector harness electrical connector.

7. Pull up the lock release of the fuel injector connector (1).

8. Depress the lock tab (1) and lift the connector from the injector.
9. Remove the injector electrical harness from the fuel rail.
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 3
Chevrolet Venture V6-3.4L VIN E 372
10. Disconnect the coolant temperature sensor electrical connector.

11. Remove the fuel rail retaining bolts.


12. Remove the fuel rail assembly.
13. Remove the injector O-ring seal from spray tip end of each injector.

INSTALLATION PROCEDURE

NOTE
^ Use care when servicing the fuel system components, especially the fuel injector electrical connectors, the fuel injector tips, the injector
O-rings. Plug the inlet and the outlet ports of the fuel rail in order to prevent contamination.
^ Do not use the compressed air to clean the fuel rail assembly as this may damage the fuel rail components.
^ Do not immerse the fuel rail assembly in a solvent bath in order to prevent damage to the fuel rail assembly.

1. Install The fuel rail assembly into the intake manifold. Tilt rail assembly to install injectors.

NOTE: Refer to Fastener Notice in Service Precautions.

2. Install the fuel rail attaching bolts.

Tighten
Tighten the fuel rail attaching bolt to 10 N.m (7 lb ft).
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 4
Chevrolet Venture V6-3.4L VIN E 373

3. Connect the coolant temperature sensor electrical connector.

4. Install the injector electrical harness to the fuel rail.


5. Connect the injector connectors (2).
6. Push the slide locks (1) into position.

7. Connect the main injector harness electrical connector.


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 5
Chevrolet Venture V6-3.4L VIN E 374

8. Install the new O-rings on fuel feed pipe and fuel return pipe.
9. Install the fuel feed pipe at the fuel rail.

Tighten
Tighten the fuel feed pipe nut to 17 N.m (13 lb ft).

10. Connect the fuel return pipe at the fuel pressure regulator.

Tighten
Tighten the fuel return pipe nut to 17 N.m (13 lb ft).

11. Install the upper intake manifold.

CAUTION: Refer to Battery Disconnect Caution in Service Precautions.

12. Connect the negative battery cable.


13. Inspect for fuel leaks using the following procedure:
13.1. Turn ON the ignition, for 2 seconds.
13.2. Turn OFF the ignition, for 10 seconds.
13.3. Turn ON the ignition.
13.4. Inspect for fuel leaks.
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 1
Chevrolet Venture V6-3.4L VIN E 375
Fuel Supply Line: Service and Repair
Filter to Tank
CAUTION: In order to Reduce the Risk of Fire and Personal injury:
^ if nylon fuel pipes are nicked, scratched or damaged during installation, Do Not attempt to repair the sections of the nylon fuel pipes.
Replace them.
^ When installing new fuel pipes, Do Not hammer directly on the fuel harness body clips as it may damage the nylon pipes resulting in
a possible fuel leak.
^ Always cover nylon vapor pipes with a wet towel before using a torch near them. Also, never expose the vehicle to temperatures
higher than 115°C (239°F) for more than one hour, or more than 90°C (194°F) for any extended period.
^ Before connecting fuel pipe fittings, always apply a few drops of clean engine oil to the male pipe ends. This will ensure proper
reconnection and prevent a possible fuel leak. (During normal operation, the O-rings located in the female connector will swell and
may prevent proper reconnection if not lubricated.)

NOTE: Do not attempt to straighten any kinked nylon fuel lines. Replace any kinked nylon fuel feed or return pipes in order to prevent damage
to the vehicle.

REMOVAL PROCEDURE

1. Relieve the fuel system fuel pressure. Refer to Fuel Pressure Relief Procedure.
2. Drain the fuel tank. Refer to Fuel Tank Draining Procedure.
3. Raise the vehicle. Refer to Lifting and Jacking the Vehicle in general information.
4. Remove the quick-connect fittings on the fuel feed and return pipes at the in-pipe fuel filter.
5. Cap the fuel sender fuel pipes and the in-pipe fuel filter pipes as needed to stop any fuel leakage.
6. Remove the fuel tank.

7. Remove the fuel feed and fuel return pipe attaching hardware.
8. Remove the fuel feed and fuel return pipes from the fuel tank.
9. Note the position of the fuel feed and return pipes and attaching hardware for installation.

INSTALLATION PROCEDURE

CAUTION: In order to Reduce the Risk Of Fire and Personal Injury: If nylon fuel pipes are nicked, scratched or damaged during
installation, they must be replaced.
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 2
Chevrolet Venture V6-3.4L VIN E 376

1. Remove the caps from the fuel sender fuel pipes.


2. Install new plastic connector retainers on the in-pipe fuel filter pipes and on the fuel sender fuel pipes.
3. Install the new fuel feed, fuel return pipes to the fuel tank as noted during removal.
4. Connect the quick-connect fittings on the fuel feed, and return pipes at the fuel tank.
5. Install the fuel pipe attaching hardware as noted during removal.
6. Install the fuel tank.

7. Remove the caps from the in-pipe fuel filter pipes.


8. Connect the quick-connect fittings on the fuel feed and return pipes at the in-pipe fuel filter.
9. Add fuel, and tighten the fuel fill cap.
10. Connect the negative battery cable.
11. Inspect for fuel leaks using the following procedure:
11.1. Turn ON the ignition, for 2 seconds.
11.2. Turn OFF the ignition, for 10 seconds.
11.3. Turn ON the ignition.
11.4. Inspect for fuel leaks.
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 1
Chevrolet Venture V6-3.4L VIN E 377
Fuel Supply Line: Service and Repair
Chassis
REMOVAL PROCEDURE

1. Relieve the fuel system fuel pressure. Refer to Fuel Pressure Relief Procedure.
2. Raise the vehicle. Refer to Lifting and Jacking the Vehicle in Service Precautions.
3. Disconnect the fuel feed and return pipe quick-connect fittings at the front frame rail.

4. Disconnect the fuel feed and return pipe quick-connect fittings at the out let side of the fuel filter.
5. Cap the in-pipe fuel filter pipes, and the engine fuel feed pipe, and engine fuel return pipe as needed to stop any fuel leakage.
6. Remove the fuel feed and return pipes.
7. Note the position of the fuel pipes for installation.

INSTALLATION PROCEDURE

1. Install the fuel feed and return pipes as noted on removal.


2. Remove the caps from the in-pipe fuel filter pipes, the engine fuel feed pipe, and the engine fuel return pipe.
3. Install new plastic connector retainers on the in-pipe fuel filter, the fuel feed pipe, and the return pipe.
4. Connect the fuel feed and return pipe quick-connect fittings at the outlet side of the fuel filter.

5. Connect the fuel feed and return pipe quick-connect fittings at the front frame rail.
6. Lower the vehicle.
7. Tighten the fuel fill cap.
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 2
Chevrolet Venture V6-3.4L VIN E 378
8. Inspect for fuel leaks.
8.1. Turn the ignition switch ON for 2 seconds.
8.2. Turn the ignition switch OFF for 10 seconds.
8.3. Turn the ignition switch ON.
8.4. Check for fuel leaks.
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 1
Chevrolet Venture V6-3.4L VIN E 379
Fuel Supply Line: Service and Repair
Engine Compartment (Engine Pipes)
REMOVAL PROCEDURE

TOOLS REQUIRED
J 37088-A Fuel Pipe Quick-Connect Separator

NOTE: Do not attempt to repair the engine fuel feed pipe or the engine fuel return pipe. Replace a damaged engine fuel feed pipe or the engine
fuel return pipe.

1. Relieve the fuel system fuel pressure. Refer to Fuel Pressure Relief Procedure.
2. Clean all engine fuel pipe connections and areas surrounding the engine fuel pipe connections before disconnecting the engine fuel pipe
connections to avoid possible contamination of the fuel system.
3. Disconnect the quick-connect fittings in the engine compartment.
4. Plug the chassis fuel feed pipe and the chassis fuel return pipe as required.
5. Remove the upper intake manifold assembly.

6. Disconnect the engine fuel return pipe from the fuel pressure regulator. Discard the O-ring.

7. Disconnect the engine fuel feed pipe from the fuel rail. Discard the O-ring.
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 2
Chevrolet Venture V6-3.4L VIN E 380

INSTALLATION PROCEDURE

1. Lubricate the new O-ring with clean engine oil, then connect the O-ring and the engine fuel return pipe to the fuel pressure regulator.

NOTE: Refer to Fastener Notice in Service Precautions.

2. Lubricate the new O-ring with clean engine oil, then connect the O-ring and the engine fuel feed pipe to the fuel rail.

Tighten
Tighten the engine fuel pipe fittings to 17 N.m (13 lb ft).

3. Install the upper intake manifold assembly.


4. Connect the quick-connect fittings in the engine compartment.
5. Tighten the fuel fill cap.
6. Inspect for fuel leaks using the following procedure:
6.1. Turn ON the ignition, for 2 seconds.
6.2. Turn OFF the ignition, for 10 seconds.
6.3. Turn ON the ignition.
6.4. Inspect for fuel leaks.
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 1
Chevrolet Venture V6-3.4L VIN E 381
Fuel Supply Line: Service and Repair
Engine Compartment (Engine Compartment)
REMOVAL PROCEDURE

TOOLS REQUIRED
J 37088-A Fuel Pipe Quick-Connect Separator

CAUTION: In order to Reduce the Risk of Fire and Personal Injury:


^ If nylon fuel pipes are nicked, scratched or damaged during installation, Do Not attempt to repair the sections of the nylon fuel pipes.
Replace them.
^ When installing new fuel pipes, Do Not hammer directly on the fuel harness body clips as it may damage the nylon pipes resulting in
a possible fuel leak.
^ Always cover nylon vapor pipes with a wet towel before using a torch near them. Also, never expose the vehicle to temperatures
higher than 115°C (239°F) for more than one hour, or more than 90°C (194°F) for any extended period.
^ Before connecting fuel pipe fittings, always apply a few drops of clean engine oil to the male pipe ends. This will ensure proper
reconnection and prevent a possible fuel leak. (During normal operation, the O-rings located in the female connector will swell and
may prevent proper reconnection if not lubricated.)

NOTE: Do not attempt to straighten any kinked nylon fuel lines. Replace any kinked nylon fuel feed or return pipes in order to prevent damage
to the vehicle.

1. Relieve the fuel system fuel pressure. Refer to Fuel Pressure Relief Procedure.

IMPORTANT: Clean all engine fuel pipe connections and areas surrounding the engine fuel pipe connections before disconnecting the engine
fuel pipe connections to avoid possible contamination of the fuel system.

2. Disconnect the quick-connect fittings in the engine compartment.


3. Raise the vehicle. Refer to Lifting and Jacking the Vehicle in Service Precautions.

4. Disconnect the quick-connect fitting at the front frame rail.


5. Gap the fuel feed pipe and the fuel return pipe as needed to stop any fuel leakage.
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 2
Chevrolet Venture V6-3.4L VIN E 382

6. Remove the fuel feed and fuel return pipe attaching hardware and the fuel feed and fuel return pipes.
7. Note the position of the fuel feed and return pipes and the fuel feed and return pipe attaching hardware for installation.
8. Inspect the pipes for bends, kinks and cracks.
9. Replace the fuel pipes if necessary.

INSTALLATION PROCEDURE

CAUTION: In order to Reduce the Risk of Fire and Personal Injury: If nylon fuel pipes are nicked, scratched or damaged during
installation, they must be replaced.

1. Install the new fuel feed and return pipes and the fuel pipe attaching hardware as noted during removal.
2. Remove the caps from the fuel feed pipe and the fuel return pipe.
3. Install new plastic connector retainers on the fuel pipes.

4. Connect the quick-connect fitting at the front frame rail. Quick Connect Fitting(s) Service (Metal Collar)
5. Lower the vehicle.
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 3
Chevrolet Venture V6-3.4L VIN E 383

6. Connect the quick-connect fittings in the engine compartment.


7. Add fuel and tighten the fuel fill cap.
8. Inspect for fuel leaks using the following procedure:
8.1. Turn ON the ignition, for 2 seconds.
8.2. Turn OFF the ignition for 10 seconds.
8.3. Turn ON the ignition.
8.4. Inspect for fuel leaks.
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 1
Chevrolet Venture V6-3.4L VIN E 384
Fuel Tank: Testing and Inspection
IMPORTANT: Before attempting the Fuel Tank Leak Check place a dry chemical (Class B) fire extinguisher near the work area.
1. Install the J 41415-40 Fill Tank Cap Adaptor.
2. Connect the J 41413 EVAP Pressure/Purge Diagnostic Station to the fill tank cap adaptor.
3. With a scan tool, seal the EVAP system.
4. Raise the vehicle on a hoist. Refer to Vehicle Lifting Caution in Service Precautions.
5. With the Evaporative Emission System (EVAP) diagnostic station, maintain 15 in. H2O (3.75 kPa) within the fuel tank.

IMPORTANT: It may be necessary to partially lower the fuel tank to inspect the top of the fuel tank and fuel sender assembly O-ring. Refer to
Fuel Tank Replacement.

6. With the J 41416 ultrasonic leak detector, test for leaks in the fuel tank and EVAP pipes.
7. Visually inspect for fuel leaking from the fuel tank.
8. If a leak is detected refer to the following component replacements:
^ Fuel tank leak, refer to Fuel Tank Replacement.
^ Fuel sender O-ring or fuel sender leak, refer to Fuel Sender Assembly Replacement.
^ Fuel or EVAP pipe leak, refer to Fuel Hose/Pipes Replacement (Filter to Tank) in Fuel Supply Line or Fuel Return Line.
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 1
Chevrolet Venture V6-3.4L VIN E 385
Fuel Tank: Removal and Replacement
REMOVAL PROCEDURE

NOTE: Do not attempt to straighten any kinked nylon fuel lines. Replace any kinked nylon fuel feed or return pipes in order to prevent damage
to the vehicle.

IMPORTANT: Do not attempt to repair sections of nylon fuel pipes. If the nylon fuel pipes are damaged, replace the pipes.

1. Relieve the fuel system fuel pressure. Refer to Fuel Pressure Relief Procedure.
2. Drain the fuel tank. Refer to Fuel Tank Draining Procedure.
3. Raise the vehicle. Refer to Lifting and Jacking the Vehicle in Service Precautions.
4. Disconnect the quick-connect fitting at the inlet side of the in-pipe fuel filter.
5. Disconnect the quick-connect fitting on the fuel return pipe, near the fuel filter.

6. Disconnect the fuel tank EVAP pipe quick-connect fitting at the EVAP pipe canister.
7. Remove the EVAP fuel filler pipe from the side of the fuel tank.

8. Loosen the fuel tank filler pipe hose clamp.


9. Remove the fuel tank filler pipe.
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 2
Chevrolet Venture V6-3.4L VIN E 386

10. Loosen the fuel tank filler vent hose clamp.


11. Remove the fuel tank filler vent hose at the filler neck.

12. With the aid of an assistant, support the fuel tank and remove the fuel tank strap attaching bolts.
13. Disconnect the fuel sender electrical connector.
14. Disconnect the fuel tank pressure sensor electrical connector.

15. Remove the fuel tank from the vehicle and place the fuel tank in a suitable work area.
16. If the fuel tank is not being replaced, go to the Installation Procedure.

17. Disconnect the fuel feed and return pipe quick-connect fittings.
18. Remove the fuel feed pipe.
19. Remove the fuel return pipe.
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 3
Chevrolet Venture V6-3.4L VIN E 387

20. Remove the EVAP pipe assembly.


21. Remove the fuel sender assembly.

INSTALLATION PROCEDURE

1. Install the fuel sender assembly.


2. Install the EVAP pipe assembly.

3. Install the fuel feed pipe.


4. Install the fuel return pipe.
5. Connect the quick-connect fittings at the fuel sender.

6. With the aid of an assistant, position and support the fuel tank.
7. Connect the fuel sender electrical connector and the fuel sender retaining clips.
8. Connect the fuel tank pressure sensor electrical connector.

NOTE: Refer to Fastener Notice in Service Precautions.


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 4
Chevrolet Venture V6-3.4L VIN E 388

9. Install the fuel tank retaining strap attaching bolts.

Tighten
Tighten the fuel tank retaining strap bolts to 47.5 N.m (35 lb ft).

10. Connect the fuel tank filler vent hose to the fuel tank.

Tighten
Tighten the fuel tank filler vent hose clamp to 2.5 N.m (22 lb in).

11. Connect the fuel tank filler pipe to the fuel tank.

Tighten
Tighten the fuel tank filler pipe hose clamp to 2.5 N.m (22 lb in).

12. Connect the fuel feed pipe quick-connect fitting at the inlet side of the fuel filter.
13. Connect the fuel return pipe quick-connect fitting near the fuel filter.
14. Connect the EVAP fuel filler pipe to the side of the fuel tank.
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 5
Chevrolet Venture V6-3.4L VIN E 389

15. Connect the fuel tank EVAP pipe quick-connect fitting at the EVAP canister.

16. Lower the vehicle.


17. Add fuel and Install the fuel tank filler pipe cap.
18. Reconnect the negative battery cable.
19. Inspect for fuel leaks using the following procedure:
19.1. Turn ON the ignition, for 2 seconds.
19.2. Turn OFF the ignition, for 10 seconds.
19.3. Turn ON the ignition.
19.4. Inspect for fuel leaks.
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 1
Chevrolet Venture V6-3.4L VIN E 390
Fuel Gauge Sender: Service and Repair

REMOVAL PROCEDURE
1. Relieve fuel system pressure. Refer to Fuel Pressure Relief Procedure.
2. Drain fuel tank. Refer to Fuel Tank Draining Procedure.
3. Remove the fuel tank.
4. Remove the fuel sender assembly.
5. Remove the fuel level sensor (5) from the modular fuel sender.

INSTALLATION PROCEDURE
1. Install the fuel level sensor (5) to the modular fuel sender.
2. Install the fuel sender assembly.
3. Install the fuel tank.
4. Lower the vehicle.
5. Add fuel and Install the fuel fill cap.
6. Inspect for fuel leaks using the following procedure:
6.1. Turn ON the ignition, for 2 seconds.
6.2. Turn OFF the ignition, for 10 seconds.
6.3. Turn ON the ignition.
6.4. Inspect for fuel leaks.
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 1
Chevrolet Venture V6-3.4L VIN E 391
Fuel Tank Unit: Service and Repair

REMOVAL PROCEDURE

TOOL REQUIRED
J 39348 Fuel Sender Spanner Wrench

NOTE: Do Not handle the fuel sender assembly by the fuel pipes. The amount of leverage generated by handling the fuel pipes could damage
the joints.

IMPORTANT: Always replace the fuel sender gasket when Installing the fuel sender assembly.

1. Relieve the fuel system fuel pressure. Refer to Fuel Pressure Relief Procedure.
2. Drain the fuel tank. Refer to Fuel Tank Draining Procedure.
3. Raise the vehicle. Refer to Lifting and Jacking the Vehicle in Service Precautions.
4. Remove the fuel tank.
5. Clean all of the fuel pipe connections, all of the hose connections, and all of the areas surrounding the connections before disconnecting the
connections in order to avoid possible contamination of the fuel system.
6. Disconnect the quick-connect fittings at the fuel sender assembly.
7. Use the J 39348 fuel sender spanner wrench in order to remove the fuel sender assembly locking nut, the fuel sender assembly and the O-ring
from the fuel tank.
8. Discard the fuel sender assembly O-ring.

INSTALLATION PROCEDURE
1. Clean the fuel sender assembly O-ring sealing surfaces.
2. Position the new fuel sender assembly O-ring on the fuel tank.

IMPORTANT: Care should be taken not to fold over or twist the fuel pump strainer when installing the fuel sender assembly, as this will
restrict fuel flow. Also, assure that the fuel pump strainer does not block full travel of float arm.

3. Use the J 39348 fuel sender wrench in order to install the fuel sender assembly and the fuel sender assembly locking nut.
4. Connect the quick-connect fittings at the fuel sender assembly.
5. Install the fuel tank.
6. Lower the vehicle.
7. Add fuel and Install the fuel fill cap.
8. Connect the negative battery cable.
9. Inspect for fuel leaks using the following procedure:
9.1. Turn ON the ignition, for 2 seconds.
9.2. Turn OFF the ignition, for 10 seconds.
9.3. Turn ON the ignition.
9.4. Inspect for fuel leaks.
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 1
Chevrolet Venture V6-3.4L VIN E 392
Idle Air Control Motor (IAC): Service and Repair
REMOVAL PROCEDURE

1. Turn OFF the ignition.


2. Disconnect the Idle Air Control (IAC) electrical connector.

3. Remove the IAC valve attaching screws.

4. Remove the idle air control valve.

5. Remove the idle air control valve O-ring.

INSTALLATION PROCEDURE

NOTE: The IAC valve may be damaged if installed with the cone (pintle) extended more than 28 mm (1-1/8 in). Measure the distance that the
valve is extended before installing a new valve. The distance from the idle air control valve motor housing to the end of the idle air control valve
pintle should be less than 28 mm (1-1/8 in). Manually compressing the pintle until the extension is less than 28 mm (1-1/8 in).

1. Install the new idle air control O-ring.


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 2
Chevrolet Venture V6-3.4L VIN E 393

2. Install the idle air control valve into the throttle body.

NOTE: Refer to Fastener Notice in Service Precautions.

3. Install the idle air control valve attaching screws.

Tighten
The screws to 3.0 N.m (27 lb in).

4. Connect the Idle Air Control (IAC) electrical connector.


5. The PCM will reset the idle air control valve whenever the ignition switch is turned ON, then OFF. Turn the ignition switch ON, then OFF.
6. Start the engine and allow the engine to reach operating temperature.
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 1
Chevrolet Venture V6-3.4L VIN E 394
Throttle Position Sensor: Service and Repair
REMOVAL PROCEDURE

1. Disconnect the Intake Air Temperature (IAT) electrical connector and breather tube from the air intake tube.
2. Remove the air intake tube.

3. Disconnect the TP sensor electrical connector.

4. Remove the 2 TP sensor attaching screws.


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 2
Chevrolet Venture V6-3.4L VIN E 395

5. Remove the TP sensor.

6. Remove the TP sensor O-ring.

INSTALLATION PROCEDURE

1. Install the IP sensor O-ring.


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 3
Chevrolet Venture V6-3.4L VIN E 396

2. With the throttle valve in the normal closed idle position, install the TP sensor on the throttle body assembly.

NOTE: Refer to Fastener Notice in Service Precautions.

3. Install the 2 TP sensor attaching screws, using a thread-locking compound on the screws. Loctite(R) 262, GM P/N #1052624, or equivalent
should be used.

Tighten
Tighten the TP sensor attaching screws to 2.0 N.m (18 lb in).

4. Connect the TP sensor electrical connector.


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 4
Chevrolet Venture V6-3.4L VIN E 397

5. Reinstall the air inlet tube.


6. Connect the IAT electrical connector and breather tube to the air inlet tube.
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 1
Chevrolet Venture V6-3.4L VIN E 398
Throttle Body: Service and Repair
REMOVAL PROCEDURE

1. Drain coolant. Refer to Draining and Filling Cooling System.


2. Disconnect the IAT sensor electrical connector.
3. Disconnect the breather tube from the air intake tube.
4. Lossen the air intake tube clamps and remove the air intake tube.

5. Disconnect the Idle Air Control (IAC) valve electrical connector.

6. Disconnect the Throttle Position (TP) sensor electrical connector.


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 2
Chevrolet Venture V6-3.4L VIN E 399

7. Disconnect the accelerator controls cable.

8. If applicable disconnect the cruse control cable from the throttle lever and cable bracket.

9. Remove the accelerator control cable bracket.


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 3
Chevrolet Venture V6-3.4L VIN E 400

10. Disconnect the throttle body coolant bypass hoses.


11. Disconnect the heater pipe nut at the throttle body.
12. Remove the nuts and bolts holding the throttle body to the intake manifold.
13. Remove the throttle body assembly.

INSTALLATION PROCEDURE

NOTE: Do Not use solvent of any type when cleaning the gasket surfaces on the intake manifold and the throttle body assembly, as damage to
the gasket surfaces and throttle body assembly may result.

Use care in cleaning the gasket surfaces on the intake manifold and the throttle body assembly, as sharp tools may damage the gasket surfaces.

1. Clean the gasket surface on the intake manifold and the throttle body assembly.
2. Install a new gasket, if necessary.
3. Install the throttle body assembly.

NOTE: Refer to Fastener Notice in Service Precautions.

4. Install the throttle body retaining nuts and bolts.

Tighten
Tighten the throttle body retaining nuts and bolts to 28 N.m (21 lb ft).

5. Connect the throttle body coolant bypass hoses.


6. Connect the heater pipe nut at the throttle body.

7. Connect the IAC valve electrical connector.


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 4
Chevrolet Venture V6-3.4L VIN E 401

8. Connect the TP sensor electrical connector.

9. Install the accelerator controls cable bracket.

10. Connect the accelerator controls cable.


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 5
Chevrolet Venture V6-3.4L VIN E 402

11. If applicable connect the cruse cable to the throttle lever and accelerator bracket.

12. Install the air intake tube and tighten the clamps.
13. Connect the IAT sensor electrical connector.
14. Connect the breather tube to the air intake tube.
15. Refill the coolant.

IMPORTANT: The throttle should operate freely without binding between full closed and wide open throttle.

16. Inspect for complete throttle opening and closing positions by operating the accelerator pedal. Also inspect for poor carpet fit under the
accelerator pedal.
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 1
Chevrolet Venture V6-3.4L VIN E 403
Throttle Cable/Linkage: Service and Repair
Accelerator Controls Cable Replacement
REMOVAL PROCEDURE

1. Remove the left instrument panel sound insulator.


2. Disconnect the accelerator cable from the accelerator pedal.
3. Squeeze the accelerator cable cover tangs and push the accelerator cable through the bulkhead.

4. Remove the accelerator cable shield, if equipped.


5. Disconnect the accelerator cable from the retaining clip.
6. Disconnect the accelerator cable from the throttle body lever.
7. Disconnect the accelerator cable from the accelerator cable bracket.

8. Remove the accelerator cable from the vehicle. Note the cable routing for aid in installation.

INSTALLATION PROCEDURE

NOTE: Do not route flexible components (hoses, wires, conduits, etc.) within 50 mm (2 in) of moving parts unless flexible components can be
securely fastened. This is necessary in order to prevent possible interference and damage to the component.
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 2
Chevrolet Venture V6-3.4L VIN E 404

1. Install accelerator cable into car using routing noted during removal.

2. Install the snap retainer through the bulkhead.


3. Connect the accelerator cable through the slot in the accelerator pedal lever.
4. Seat the snap retainer in the accelerator pedal lever.

5. Connect the accelerator cable to the throttle body lever.


6. Connect the accelerator cable to the accelerator cable bracket.
7. Connect the accelerator cable into the retaining clip.
5. Reinstall the accelerator cable shield, if equipped.
9. Inspect and check for complete throttle opening and closing positions by operating the accelerator pedal. Also check for poor carpet fit under
the accelerator pedal.
10. Reinstall the left instrument panel sound insulator.
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 1
Chevrolet Venture V6-3.4L VIN E 405
Throttle Cable/Linkage: Service and Repair
Accelerator Controls Cable Bracket Replacement
REMOVAL PROCEDURE

1. Disconnect the accelerator cable cross slug from throttle body slot.
2. Depress the tangs and remove the accelerator cable from accelerator cable bracket.

3. If applicable disconnect the cruse control cable from the throttle lever and accelerator bracket.

4. Remove the nut (3) and bolts (1,2) holding the accelerator cable bracket to the throttle body.
5. Remove the accelerator cable bracket.

INSTALLATION PROCEDURE
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 2
Chevrolet Venture V6-3.4L VIN E 406

1. Position the accelerator cable bracket on the throttle body.

NOTE: Refer to Fastener Notice in Service Precautions.

2. Install the nut (3) and bolts (1,2).

Tighten
^ Tighten the bolts in sequence (2,1) to 13 N.m (115 lb in).
^ Tighten the nut in sequence (3) to 10 N.m (89 lb in).

3. Connect the cruise control cable into accelerator cable bracket.


4. Connect the accelerator cable cross slug to the throttle body slots.
5. If applicable connect the cruse control cable to the throttle lever and accelerator bracket.
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 1
Chevrolet Venture V6-3.4L VIN E 407
Computers and Control Systems: Description and Operation
Information Sensors/Switches

Camshaft Position (CMP) Sensor And Cam Signal


The camshaft position sensor sends a cam signal to the PCM which uses it as a sync pulse to trigger the injectors in proper sequence. The PCM uses
the CAM signal to indicate the position of the #1 piston during its intake stroke. This allows the PCM to calculate true Sequential Fuel Injection
(SFI) mode of operation. If the PCM detects an incorrect CAM signal while the engine is running, DTC P0341 Camshaft Position (CMP) Sensor
Performance will set.

If the CAM signal is lost while the engine is running, the fuel injection system will shift to a calculated sequential fuel injection mode based on the
last fuel injection pulse, and the engine will continue to run.

The engine can be restarted and will run in the calculated sequential mode as long as the fault is present with a 1 in 6 chance of injector sequence
being correct.
EGR Pintle Position Sensor
The EGR pintle position sensor is an integral part of the EGR valve assembly. This sensor can not be serviced separately from the EGR valve
assembly.

The PCM monitors the EGR valve pintle position input to ensure that the valve responds properly to commands from the PCM and to detect a fault
if the pintle position sensor and control circuits are open or shorted.
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 2
Chevrolet Venture V6-3.4L VIN E 408

Linear EGR Control

If the PCM detects a pintle position signal voltage outside the normal range of the pintle position sensor, or a signal voltage that is not within a
tolerance considered acceptable for proper EGR system operation, the PCM sets DTC P1404 EGR Valve Stuck Open.
Engine Coolant Temperature (ECT) Sensor
The engine coolant temperature sensor is a thermistor (a resistor which changes value based on temperature) mounted in the engine coolant stream.

Low coolant temperature produces a high resistance (100,000 ohms at -40°C/-40°F) while high temperature causes low resistance (70 ohms at 130
°C/266°F).

The PCM supplies a 5 volt signal to the engine coolant temperature sensor through a resistor in the PCM and measures the voltage. The voltage is
high when the engine is cold, and low when the engine is hot. By measuring the voltage, the PCM calculates the engine coolant temperature. The
engine coolant temperature affects most systems the PCM controls.
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 3
Chevrolet Venture V6-3.4L VIN E 409

The scan tool displays engine coolant temperature in degrees. After engine startup, the temperature should rise steadily to about 90°C (194°F) then
stabilize when thermostat opens. If the engine has not been run for several hours (overnight), the engine coolant temperature and intake air
temperature displays should be close to each other. A hard fault in the engine coolant sensor circuit should set DTC P0117 Engine Coolant
Temperature (ECT) Sensor Circuit Low Voltage, or DTC P0118 Engine Coolant Temperature (ECT) Sensor Circuit High Voltage. The DTC
Diagnostic Aids also contains a chart to check for sensor resistance values relative to temperature.

The ECT sensor (3) also contains another circuit which is used to operate the engine coolant temperature gauge located in the instrument panel.

Engine Oil Level Switch

The PCM monitors the engine oil level switch signal at start-up to determine if the engine oil is OK. If the PCM determines that a low oil level
condition exists, the PCM will communicate the information over the Class II circuit to the IPC and it will illuminate the indicator lamp.
Engine Oil Pressure Switch
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 4
Chevrolet Venture V6-3.4L VIN E 410

The PCM monitors the engine oil pressure switch (1) signal to determine if the engine oil pressure is OK. If the PCM determines that a low oil
pressure condition exists, the PCM will communicate the information over the Class II circuit to the IPC and it will illuminate the indicator lamp.
Fuel Control Heated Oxygen Sensor (HO2S 1)

Fuel Control Heated Oxygen Sensor (HO2S 1)

The fuel control Heated Oxygen Sensor (HO2S 1) is mounted in the exhaust manifold where the sensor can monitor the oxygen content of the
exhaust gas stream. The oxygen present in the exhaust gas reacts with the sensor to produce a voltage output.

This voltage should constantly fluctuate from approximately 100 mV (high oxygen content lean mixture) to 900 mV (low oxygen content rich
mixture). The heated oxygen sensor voltage can be monitored with a scan tool. By monitoring the voltage output of the oxygen sensor, the PCM
calculates what fuel mixture command to give to the injectors (lean mixture/low HO2S voltage = rich command, rich mixture/high HO2S voltage =
lean command).
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 5
Chevrolet Venture V6-3.4L VIN E 411

The HO2S 1 circuit, if open, should set a DTC P0134 HO2S Circuit Insufficient Activity Sensor 1 and the scan tool should display a constant
voltage between 400 and 500 mV. A constant voltage below 300 mV in the sensor circuit (circuit grounded) should set DTC P0131 HO2S Circuit
Low Voltage Sensor 1, while a constant voltage above 800 mV in the circuit should set DTC P0132 HO2S Circuit High Voltage Sensor 1. A fault
in the HO2S 1 heater circuit should cause DTC P0135 to set. The PCM can also detect HO2S response problems. If the response time of an HO2S
is determined to be too slow, the PCM stores a DTC that indicates degraded HO2S performance.
General Description
All of the sensors and input switches can be diagnosed using a scan tool. Following is a short description of how the sensors and switches can be
diagnosed by using a scan tool. The scan tool can also be used to compare the values for a normal running engine with the engine you are
diagnosing.
Intake Air Temperature (IAT) Sensor
The Intake Air Temperature (IAT) sensor is a thermistor which changes value based on the temperature of air entering the engine. Low temperature
produces a high resistance (100,000 ohms at -40°C/-40°F), while high temperature causes low resistance (70 ohms at 130°C/266°F).

The PCM supplies a 5 volt signal to the sensor through a resistor in the PCM and measures the voltage. The voltage is high when the incoming air
is cold, and low when the air is hot. By measuring the voltage, the PCM calculates the incoming air temperature. The IAT sensor signal is used to
adjust the spark timing according to incoming air density.

The scan tool displays the temperature of the air entering the engine, which should read close to the ambient air temperature when the engine is
cold, and rise as the underhood temperature increases.
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 6
Chevrolet Venture V6-3.4L VIN E 412

If the engine has not been run for several hours (overnight) the IAT sensor temperature and the engine coolant temperature should read close to
each other. A failure in the IAT sensor circuit should set DTC P0112 Intake Air Temperature (IAT)Sensor Circuit Low Voltage or DTC P0113
Intake Air Temperature (IAT) Sensor Circuit High Voltage.
Knock Sensor (KS)

The knock sensor detects abnormal vibration (spark knocking) in the engine. The sensor is located on the engine block near the cylinders. The
sensor produces an AC output voltage which increases with the severity of the knock. This signal voltage is input to the PCM. The PCM then
adjusts the Ignition Control (IC) timing to reduce spark knock. DTC P0325 Knock Sensor (KS) Circuit DTC P0327 Knock Sensor (KS) Circuit are
designed to diagnose the PCM, the knock sensor, and related wiring, so problems encountered with the KS system should set a DTC.

Refer to Knock Sensor (KS) System Description.


Manifold Absolute Pressure (MAP) Sensor
The Manifold Absolute Pressure (MAP) sensor responds to changes in intake manifold pressure (vacuum). The MAP sensor signal voltage to the
PCM varies from below 2 volts at idle (high vacuum) to above 4 volts with the key ON and the engine not running or at wide open throttle (low
vacuum).

The MAP sensor is used to determine manifold pressure changes while the linear EGR flow test diagnostic is being run (Refer to DTC P0401
Exhaust Gas Recirculation (EGR) Flow Insufficient ),to determine engine vacuum level for other diagnostics, and to determine Barometric
Pressure (BARO).
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 7
Chevrolet Venture V6-3.4L VIN E 413

If the PCM detects a voltage that is lower than the possible range of the MAP sensor, DTC P0107 Manifold Absolute Pressure (MAP) Sensor
Circuit Low Voltage is set. A signal voltage higher than the possible range of the sensor sets DTC P0108 Manifold Absolute Pressure (MAP)
Sensor Circuit High Voltage. An intermittent low or high voltage sets DTC P1107 Manifold Absolute Pressure (MAP) Sensor Circuit Intermittent
Low Voltage or DTC P1106 Manifold Absolute Pressure (MAP) Sensor Circuit Intermittent High Voltage respectively. The PCM can also detect a
shifted MAP sensor. The PCM compares the MAP sensor signal to a calculated MAP based on throttle position and various engine load factors

Mass Air Flow (MAF) Sensor


The Mass Air Flow (MAF) sensor measures the amount of air which passes through the sensor. The PCM uses this information to determine the
operating condition of the engine and to control fuel delivery.

A large quantity of air indicates acceleration, while a small quantity indicates deceleration or idle.

The scan tool reads the MAF value and displays it in grams per second (gm/s). The MAF value should read between 4 gm/s at idle to 6 gm/s on a
fully warmed up engine. The values should change rather quickly on acceleration, but the values should remain fairly stable at any given RPM. A
failure in the MAF sensor or circuit should set DTC P0101 Mass Air Flow (MAF) Sensor Performance, DTC P0102 Mass Air Flow (MAF) Sensor
Circuit Low Frequency, or DTC P0103 Mass Air Flow (MAF) Sensor Circuit High Frequency.
PCM Controlled A/C
This vehicle may be equipped with Front(C60) and Rear(C34) A/C system. This system is designed to provide a comfortable environment inside
the passenger compartment. The Rear(C34) A/C system is controlled by the Front(C60) HVAC Control Assembly. Both electronic and vacuum
circuits determine air intake and discharge locations. PCM Controlled A/C operation is the same for either Front(C60) or the Front and Rear(C34)
HVAC system. Refer to PCM Controlled Air Conditioning Description for more information regarding the PCM Controlled Air Conditioning
system.
Throttle Position (TP) Sensor
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 8
Chevrolet Venture V6-3.4L VIN E 414

The Throttle Position (TP) sensor is a potentiometer connected to the throttle shaft on the throttle body. By monitoring the voltage on the signal
line, the PCM calculates throttle position. As the throttle valve angle is changed (accelerator pedal moved), the TP sensor signal also changes. At a
closed throttle position, the output of the TP sensor is low. As the throttle valve opens, the output increases so that at Wide Open Throttle (WOT),
the output voltage should be above 4 volts.

The PCM calculates fuel delivery based on the throttle valve angle (driver demand). A broken or loose TP sensor may cause intermittent bursts of
fuel from an injector and an unstable idle because the PCM detects that the throttle is moving. A hard failure in the TP sensor 5 volt reference or
signal circuits should set either a DTC P0122 Throttle Position (TP) Sensor Circuit Low Voltage DTC P0123 Throttle Position (TP) Sensor Circuit
High Voltage. A hard failure with the TP sensor ground circuit may set DTCs DTC P0107 Manifold Absolute Pressure (MAP) Sensor Circuit Low
Voltage, DTC P0112 Intake Air Temperature (IAT) Sensor Circuit Low Voltage, DTC P0123 Throttle Position (TP) Sensor Circuit High Voltage,
or DTC P0117 Engine Coolant Temperature (ECT) Sensor Circuit Low Voltage. Once a DTC is set, the PCM uses an artificial default value based
on engine RPM, engine load and mass air flow for throttle position and some vehicle performance returns. A high idle may result when either DTC
P0122 Throttle Position (TP) Sensor Circuit Low Voltage, or DTC P0123 Throttle Position (TP) Sensor Circuit High Voltage is set.

The PCM can detect intermittent TP sensor faults. DTC P1121 Throttle Position (TP) Sensor Circuit Intermittent High Voltage, or DTC P1122
Throttle Position (TP) Sensor Circuit Intermittent Low Voltage will set if an intermittent high or low circuit failure is being detected.
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 9
Chevrolet Venture V6-3.4L VIN E 415

The PCM can also detect a shifted TP sensor. The PCM monitors throttle position and compares the actual TP sensor reading to a predicted TP
value calculated from engine speed. If the PCM detects an out of range condition, DTC P0121 Throttle Position (TP) Sensor Performance will be
set.
Transaxle Controls
The electrical components of this unit are as follows:
^ Two shift solenoid valves: 1-2/3-4 and 2-3
^ A Torque Converter Clutch Pulse Width Modulation (TCC PWM) solenoid valve
^ A Pressure Control (PC) solenoid valve
^ An automatic Transmission Fluid Temperature (TFT) sensor
^ Two speed sensors: input shaft and vehicle speed sensors
^ An automatic Transmission Fluid Pressure (TFP) manual valve position switch
^ Either an Internal Mode Switch or an exterior-mounted Transmission Range Switch. See the data referenced by the Scan Tool or refer to
Automatic Transmission Electronic Component Views (Internal) or Automatic Transmission Electronic Component Views (External).
^ An automatic transmission (A/T) wiring harness assembly

For more information, refer to Electronic Component Description.


3X Reference
The PCM uses this signal, from the ignition control module to calculate engine speed and crankshaft position over 1600 RPM.

The PCM also uses the pulses on this circuit to initiate injector pulses. If the PCM receives no pulses on this circuit, DTC P1374 Crankshaft
Position (CKP) High to Low Resolution Frequency Correlation will set and the PCM will use the 24X reference signal circuit for fuel and ignition
control.

This is a ground circuit for the digital RPM counter inside the PCM, but the wire is connected to engine ground only through the ignition control
module. Although this circuit is electrically connected to the PCM, it is not connected to ground at the PCM.
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 10
Chevrolet Venture V6-3.4L VIN E 416

The PCM compares voltage pulses on the reference input circuits to pulses on this circuit, ignoring pulses that appear on both.

7X Crankshaft Position (CKP) Sensor

The 7X crankshaft position sensor provides a signal used by the ignition control module.

The ignition control module also uses the 7X crankshaft position sensor to generate 3X reference pulses which the PCM uses to calculate RPM and
crankshaft position.
24X Crankshaft Position (CKP) Sensor
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 11
Chevrolet Venture V6-3.4L VIN E 417

The 24X Crankshaft Position (CKP) Sensor (1) is used to improve idle spark control at engine speeds up to approximately 1600 RPM.
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 1
Chevrolet Venture V6-3.4L VIN E 418
Computers and Control Systems: Tools and Equipment

Special Tools And Equipment (Part 1 Of 3)


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 2
Chevrolet Venture V6-3.4L VIN E 419

Special Tools And Equipment (Part 2 Of 3)


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 3
Chevrolet Venture V6-3.4L VIN E 420

Special Tools And Equipment (Part 3 Of 3)


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 1
Chevrolet Venture V6-3.4L VIN E 421
Body Control Module: Description and Operation
Body Control Module (BCM)
The Body Control Module (BCM) type 4 controls the content theft deterrent system.

The BCM monitors the status of the following components:


^ The vehicle doors
^ The lock cylinders
^ The shock sensor
^ The power door locks
^ The keyless entry system

The BCM operates the following components according to the chosen mode of operation:
^ The exterior lights
^ The horn
^ The status security indicator lamp
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 1
Chevrolet Venture V6-3.4L VIN E 422
Body Control Module: Description and Operation
Body Control System Circuit

Body Control System Circuit Description

This vehicle is equipped with a Body Control Module (BCM) that performs multiple body control functions. The following vehicle systems are
controlled by the BCM:
^ Audible warnings
- key in the ignition reminder
- Fasten seat belt reminder
- Driver information reminder
- Turn signal reminder
- Headlamps on reminder
- Feature customization and diagnostics mode indication
- Auxiliary chime functions (Instrument cluster)
- Last door closed locking reminder
^ Inadvertent load monitoring
^ Fasten seat belt indicator control
^ Interior light illumination
^ Power door locks functions
^ keyless entry system functions (with AUO)
^ Key cylinder lock
^ Retained Accessory Power (RAP)
^ Content theft deterrent system (with UA6)
^ Feature customization
^ Service Diagnostics

These systems are controlled by the BCM's outputs. The BCM controls its outputs based upon input information obtained from the sensors and
switches that are directly connected to the BCM. The BCM evaluates the input information and controls the body systems by commanding an
output on or off.

BCM Identification
This vehicle is equipped with 1 of 3 types of BCMs. The BCM type installed on this vehicle is based on the vehicle equipment, point of sale, and
option content. Refer to On-Board Diagnostic Features for more information on how to identify the BCM type installed by using the on-board
diagnostic feature. The following identifies the functions and basic option content of all 3 BCM types:

BCM TYPE 2
BCM type 2 is the base BCM that provides all standard BCM functions.

BCM TYPE 3
BCM type 3 provides all of the features of the BCM type 2 plus keyless entry. Vehicles with RPO AU0 are equipped with a BCM type 3.

BCM TYPE 4
BCM type 4 provides all of the features of the BCM type 2 and type 3 plus content theft deterrent. Vehicles with RPO AU0 and UA6 are
equipped with a BCM type 4.

Interior Lighting
The BCM provides the following interior light functions:
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 2
Chevrolet Venture V6-3.4L VIN E 423
^ Interior illumination
^ Delayed illumination
^ Exit illumination
^ Theatre dimming
^ Door key unlock illumination
^ keyless entry unlock illumination
^ Inadvertent load (battery rundown) protection
^ Interior light feature customization
- Delayed illumination (on/off)
- Exit lighting (on/off)

Refer to the Interior Lights Circuit Description in Lighting for customization features.

Automatic Door Locks


The BCM provides the following automatic door lock functions:
^ Door key all doors unlock
^ Door key all doors lock
^ Last door closed locking
^ Lockout prevention
^ Ignition off unlock
^ Shift into PARK unlock
^ Shift out of PARK lock
^ Sliding door delayed locking
^ Door lock feature customization
- Automatic door lock (on/off)
- Automatic door unlock (on/off)
- Last door closed lock (on/off)
- Lockout prevention (on/off)
Refer to the Automatic Door Lock System Description in Doors for customization features.

Keyless Entry (BCM TYPE 3, 4)


The BCM provides the following keyless entry functions:
^ Driver door unlock
^ All doors unlock
^ All doors lock
^ Activation verification (horn and lights)
^ Content theft alarm
^ Keyless entry feature customization
- Activation verification (lights/horn and lights/off)
- Driver door unlock only (on/off)
Refer to the Keyless Entry System Circuit Description in Keyless Entry for more information.

Content Theft Deterrent (BCM TYPE 4)


The BCM provides the following content theft deterrent functions:
^ Intrusion detection
- Doors
- Lock cylinders
- Liftgate
- Sliding doors
- Shock sensor
- Power door lock switches
^ Intrusion notification
- Flashes the exterior lights
- Sounds the horn
- Security LED
^ Content theft feature customization
- Content theft deterrent system (on/off)
- Power door lock switch arming (on/off)
- Door key cylinder arm/disarm (on/off)
- Shock sensor (on/off)
- Remote arm/disarm only (on/off)
Refer to Content Theft Deterrent (CTD) Circuit Description in Theft Deterrent for more information.

On-Board Diagnostic Mode


The Body Control Module (BCM) provides on-board diagnostics to assist in diagnosing BCM related malfunctions. The BCM has the following
diagnostic capabilities when entering the on-board diagnostic mode:
^ Feature Customization
^ Displaying DTCs
^ Clearing DTCs
^ Input/Output Diagnostics
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 3
Chevrolet Venture V6-3.4L VIN E 424

To access the on-board diagnostic mode, refer to On-Board Diagnostic Features.

For a description of the RPO Code(s) shown in this article, refer to the RPO Code List found at Vehicle/Application and ID. See: Application and
ID
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 1
Chevrolet Venture V6-3.4L VIN E 425
Body Control Module: Initial Inspection and Diagnostic Overview

A Diagnostic Starting Point - Body Control System


Begin the diagnosis of the body control system by performing the Diagnostic System Check for the system in which the customer concern is
apparent. The Diagnostic System Check will direct you to the correct procedure for diagnosing the system and where the procedure is located.

A Diagnostic System Check - Body Control System

A Diagnostic System Check - Body Control System

TEST DESCRIPTION
The number(s) below refer to the step number(s) on the diagnostic table.
1. Tests if the BCM can enter the On-Board Diagnostic Mode. Refer to On-Board Diagnostic Features. See: Reading and Clearing Diagnostic
Trouble Codes
2. The presence of DTCs stored in the BCM. The specified procedure will compile all the available information before tests are performed.
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 1
Chevrolet Venture V6-3.4L VIN E 426
Body Control Module: Reading and Clearing Diagnostic Trouble Codes

Diagnostic Trouble Code (DTC) Clearing


CLEARING DTCS
BCM DTCs can only be cleared by completing the following procedure:
1. Enter the BCM on-board diagnostic mode. Refer to On-Board Diagnostic Features.
2. Press and hold the UNLOCK button on either power door lock switch for 4 seconds.
3. All stored DTCs will clear from the BCM.

Diagnostic Trouble Code (DTC) Displaying


1. Ensure that the BCM is in the feature customization mode. Refer to On-Board Diagnostic Features.
2. Turn the ignition switch from the ACC position to the LOCK position then back to the ACC position within 1 second.

The BCM will enter the on-board diagnostic mode and flash the fasten seat belts indicator and sound the chime equal to the number of DTCs stored
in the BCM memory. If no DTCs are stored, the BCM will not flash the fasten seat belts indicator or activate the chime.

The BCM flashes and sounds the first DTC with the lowest number, pauses, then continues with the next DTC until all of the DTCs are read. With
a DTC 1, the BCM will only sound the chime once, and the fasten seat belts indicator will not flash. Once all of the DTCs are read, the BCM
repeats this sequence 3 times.

Entering Feature Customization Mode


The feature customization mode is used to configure the BCM to function in various applications. The BCM can be customized to change the
following vehicle functions:
^ Interior Lighting Features
^ Door Lock System
^ Keyless Entry System
^ Content Theft Deterrent System

In order to enter the feature customization mode perform the following steps:
1. Turn the ignition switch to the LOCK position.
2. Remove the BCM PRGRM fuse.
3. Turn the ignition switch to the ACC position. When entering the feature customization mode, the BCM first identifies what type of BCM is
installed on the vehicle by flashing the fasten seat belts indicator and sounds the chime 2, 3 or 4 times depending on the type of BCM used on
the vehicle. There are 3 different types of BCM that can be installed on the vehicle based on the vehicle option content that matches the BCM
capabilities. Ensure that the BCM installed on the vehicle is compatible with all of the features on the vehicle. Refer to Body Control System
circuit description for BCM identification. For more information on features that can be customized, refer to:
^ Interior Lights Circuit Description
^ Automatic Door Lock System Description
^ Keyless Entry System Circuit Description
^ Content Theft Deterrent (CTD) Circuit Description

Entering Input/Output Diagnostic Mode


After the BCM reads all of the DTCs in the memory, the BCM enters the Input/Output Diagnostic Mode. The BCM flashes the fasten seat belts
indicator and sounds the chime once when any of the following inputs are activated:
^ Courtesy lamp switches
^ Door lock cylinder switches
^ Driver door ajar switch
^ Driver fasten seat belt switch
^ Driver Information Display (DID)
^ Headlamp switch
^ IP compartment lamp switch
^ Keyless entry request for door lock/unlock
^ Keyless entry request for the alarm (RPO UA6)
^ Passenger door ajar switch
^ Power door lock switches
^ Liftgate ajar switch
^ Sliding door ajar switch(es)
^ Shock sensor
^ Sunshade illuminated mirrors
^ Hazard switch

Perform the following procedure in order to test the BCM outputs:


1. Ensure that the BCM is in the diagnostic mode. Refer to Entering On-Board Diagnostic Mode.
2. Cycle the interior light switch ON then OFF.
3. The BCM will enter the Output Diagnostic Test Mode 1.
4. Each cycle of the interior light switch (ON/OFF) will to select from following test modes depending on BCM type:
^ Test Mode 1- De-activates the courtesy lights output and removes power to all of the interior lamps.
^ Test Mode 2- Activates the courtesy lights output and provides power to all of the interior lamps (interior lamp override switch must be
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 2
Chevrolet Venture V6-3.4L VIN E 427
ON).
^ Test Mode 3- Activates the courtesy lights output and turns ON all of the courtesy lamps (interior lamp switch must be ON).
^ Test Mode 4- Activates the theft deterrent relay for 1 second and turns ON the headlamps (BCM type 4).
^ Test Mode 5- Energizes the horn relay for 25 ms (BCM type 4).
^ Test Mode 6- Turns on the security LED indicator (BCM type 4).
^ Test Mode 7- Turns off the security LED indicator (BCM type 4).

When the BCM completes all test modes, the BCM will repeat the test mode sequence.

Exiting Diagnostics
Perform the following procedure in order to exit the BCM diagnostics mode and return to normal BCM operation:
1. Turn the ignition switch to the LOCK position.
2. Reinstall the BCM PRGRM fuse.
3. Turn the ignition switch to the RUN position.

For a description of the RPO Code(s) shown in this article, refer to the RPO Code List found at Vehicle/Application and ID. See: Application and
ID
Entering On-Board Diagnostic Mode
Complete the following steps in order to enter the diagnostics mode:
1. Turn the ignition switch to the LOCK position.
2. Remove the BCM PRGRM fuse.
3. Turn the ignition switch to the ACC position.
4. Turn the ignition switch from the ACC position to the LOCK position then back to the ACC position within 1 second.

The BCM will enter the on-board diagnostic mode and flash the fasten seat belts indicator and sound the chime equal to the number of DTCs stored
in the BCM memory. If no DTCs are stored, the BCM will not flash the fasten seat belts indicator or activate the chime.

The BCM flashes and sounds the first DTC with the lowest number, pauses, then continues with the next DTC until all of the DTCs are read. With
a DTC 1, the BCM will only sound the chime once, and the fasten seat belts indicator will not flash. Once all of the DTCs are read, the BCM
repeats this sequence 3 times.

IMPORTANT: If the fasten seat belts indicator does not flash, and the chime does not sound, complete the following procedure in order to
confirm that the BCM has entered the diagnostics mode:

1. Ensure that all of the vehicle doors are closed.


2. Open and close any vehicle door.
3. Fasten and release the driver seat belt.

The BCM sounds the chime when receiving an input signal such as opening a door or fastening the driver seat belt when the BCM is in the
diagnostics mode.

If the BCM does not sound the chime upon opening a door or fastening the driver seat belt, repeat Step 1 of Entering the Feature Customization
Mode. If the BCM does not enter the diagnostics mode, then refer to Body Control Module Inoperative.

General Information
This vehicle is equipped with an on-board diagnostic feature capable of performing the following functions:
^ Feature Customization
^ Displaying DTCs
^ Clearing DTCs
^ Input/Output Diagnostics
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 1
Chevrolet Venture V6-3.4L VIN E 428
Body Control Module: Symptom Related Diagnostic Procedures

Diagnostic Chart

TEST DESCRIPTION
The numbers below refer to the step numbers on the diagnostic table.
2. Tests for an open in the BCM battery positive voltage circuit(s) and the ignition voltage circuit(s).
3. Tests for an open in the BCM ground circuit(s).
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 1
Chevrolet Venture V6-3.4L VIN E 429
Body Control Module: Service and Repair
REMOVAL PROCEDURE

1. Disconnect the battery negative cable.


2. Remove the left side instrument panel insulator.
3. Push the release tab on the bottom of the bracket to release the body control module.
4. Slide the body control module from the bracket.

5. Disconnect the electrical connector.

INSTALLATION PROCEDURE

1. Connect the electrical to the body control module.


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 2
Chevrolet Venture V6-3.4L VIN E 430

2. Align the tabs on the body control module with the slots in the mounting bracket. Push the body control module up until it clicks in place.
3. Install the left side instrument panel insulator.
4. Connect the battery negative cable.
5. Setup the BCMs customized options.
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 1
Chevrolet Venture V6-3.4L VIN E 431
Intake Air Temperature (IAT) Sensor: Service and Repair

REMOVAL PROCEDURE
1. Disconnect the Intake Air Temperature (IAT) sensor electrical connector (1).
2. Carefully remove the IAT sensor.

INSTALLATION PROCEDURE
1. Install the IAT Sensor (snap into place).
2. Connect the IAT sensor electrical connector (1).
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 1
Chevrolet Venture V6-3.4L VIN E 432
Data Link Connector: Service and Repair

REMOVAL PROCEDURE
1. Remove the bolts/screws from the data link connector.
2. Remove the lower data link connector.

INSTALLATION PROCEDURE
1. Place the data link connector into position.

NOTE: Refer to Fastener Notice in Service Precautions.

2. Install the bolts/screws to the data link connector.

Tighten
Tighten the bolts/screws to 2 N.m (18 lb in).
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 1
Chevrolet Venture V6-3.4L VIN E 433
EGR Valve Position Sensor: Description and Operation
The EGR pintle position sensor is an integral part of the EGR valve assembly. This sensor can not be serviced separately from the EGR valve
assembly.

The PCM monitors the EGR valve pintle position input to ensure that the valve responds properly to commands from the PCM and to detect a fault
if the pintle position sensor and control circuits are open or shorted.

Linear EGR Control

If the PCM detects a pintle position signal voltage outside the normal range of the pintle position sensor, or a signal voltage that is not within a
tolerance considered acceptable for proper EGR system operation, the PCM sets DTC P1404 EGR Valve Stuck Open.
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 1
Chevrolet Venture V6-3.4L VIN E 434
Powertrain Control Module: Description and Operation
General Description
The powertrain used in this vehicle consists of a 3.4L pushrod 60° V-6 engine mated to a 4T65-E electronically controlled transaxle. Refer to
Engine Component Description in Engine Mechanical for more information on the powertrain. The powertrain has electronic controls to reduce
exhaust emissions while maintaining excellent driveability and fuel economy. The Powertrain Control Module (PCM) is the essence of this control
system.

The PCM is designed to maintain exhaust emission levels to Federal/California/other standards while providing excellent driveability and fuel
efficiency. Review the components and wiring diagrams in order to determine which systems are controlled by the PCM. The PCM monitors
numerous engine and vehicle functions. The following are some of the functions that the PCM controls:
^ The engine fueling
^ The Ignition Control (IC)
^ The Knock Sensor (KS) system
^ The Evaporative Emissions (EVAP) system
^ The secondary Air Injection (AIR) system (if equipped)
^ The Exhaust Gas Recirculation (EGR) system
^ The automatic transmission functions
^ The generator
^ The A/C clutch control
^ The cooling fan control
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 1
Chevrolet Venture V6-3.4L VIN E 435
Powertrain Control Module: Description and Operation
PCM Function
The PCM constantly looks at the information from various sensors and other inputs and controls systems that affect vehicle performance and
emissions. The PCM also performs diagnostic tests on various pants of the system. The PCM can recognize operational problems and alert the
driver via the Malfunction Indicator Lamp (MIL). When the PCM detects a malfunction, the PCM stores a Diagnostic Trouble Code (DTC). The
problem area is identified by the particular DTC that is set. The control module supplies a buffered voltage to various sensors and switches. The
input and output devices in the control module include analog to digital converters, signal buffers, counters, and output drivers. The output drivers
are electronic switches which complete a ground circuit when turned on. Most PCM controlled components are operated via output drivers. The
PCM monitors these driver circuits for proper operation and, in most cases, can set a DTC corresponding to the controlled device if a problem is
detected.
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 1
Chevrolet Venture V6-3.4L VIN E 436
Powertrain Control Module: Service and Repair
Repair Instructions

EEPROM Programming
1. Set-up - Ensure that the following conditions have been met:
^ The battery is fully charged and battery charger is not connected.
^ The ignition is ON.
^ The Techline equipment cable connection at the DLC is secure.
2. Program the PCM using the latest software matching the vehicle. Refer to up-to-date Techline equipment users instructions.
3. If the PCM fails to program, proceed as follows:
^ Ensure that all PCM connections are OK.
^ Check the Techline equipment for the latest software version.
^ Attempt to program the PCM. If the PCM still cannot be programmed properly, replace the PCM. You must program the replacement
PCM.
Functional Check
1. Clear any DTCs.
2. Perform the A Powertrain On Board Diagnostic (OBD) System Check.
3. Start the engine and allow the engine run for one minute.
4. Use a scan tool in order to scan for the DTCs.
PCM Replacement/Programming

NOTE:
^ In order to prevent possible electrostatic discharge damage to the PCM, do not touch the connector pins or soldered components on the
circuit board.

Service of the Powertrain Control Module (PCM) should normally consist of either replacement of the PCM or Electrically Erasable
Programmable Read Only Memory (EEPROM) programming. If the diagnostic procedures call for PCM replacement, test the PCM first to
see if the PCM is the correct part. If the PCM is faulty, remove the PCM and install a new service PCM. The new service PCM is not
programmed. You must program the new PCM. DTC P0602 indicates the EEPROM is not programmed or has malfunctioned.
^ In order to prevent possible electrostatic discharge damage to the PCM, do not touch the connector pins or soldered components on the
circuit board.
^ Turn the ignition OFF when installing or removing the PCM connectors and disconnecting or reconnecting the power to the PCM (battery
cable, PCM pigtail, PCM fuse, jumper cables, etc.) in order to prevent internal PCM damage.

IMPORTANT: When replacing the production PCM with a service PCM (controller), you must transfer the broadcast code and production PCM
number to the service PCM label. Do not record the information on the PCM cover. This allows positive identification of PCM parts throughout the
service life of the vehicle.
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 2
Chevrolet Venture V6-3.4L VIN E 437

REMOVAL PROCEDURE

CAUTION: Refer to Battery Disconnect Caution in Service Precautions.

1. Disconnect the negative battery cable.


2. Remove the coolant reservoir retaining bolt.
3. Remove the coolant reservoir and set aside.
4. Remove the SMCC module from the SMCC module bracket.
5. Remove the SMCC module bracket.
6. Remove the 3 bolts from the strut brace.
7. Remove the left front strut brace.
8. Unsnap the PCM cover and remove the PCM cover from the air cleaner housing.
9. Remove the PCM from the air cleaner housing.
10. Disconnect the PCM electrical connectors.

INSTALLATION PROCEDURE
1. Connect the PCM electrical connectors to the PCM.
2. Install the PCM into the air cleaner housing.
3. Reinstall the PCM cover to the air cleaner housing and snap the retainer.
4. Reinstall the left front strut brace.

NOTE: Refer to Fastener Notice in Service Precautions.

5. Reinstall the 3 strut brace retaining bolts.


6. Reinstall the SMCC module bracket.
7. Reinstall the SMCC module to the SMCC module bracket.
8. Reinstall the coolant reservoir. Be sure to check coolant system for proper level.
9. Reconnect the negative battery cable.
10. If a new PCM is being installed, program the EEPROM.
11. The PCM will need to learn the crankshaft variation. See: Testing and Inspection/Programming and Relearning
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 1
Chevrolet Venture V6-3.4L VIN E 438
Manifold Absolute Pressure (MAP) Sensor: Service and Repair

REMOVAL PROCEDURE
1. Turn OFF the ignition.
2. Remove the attaching bolt/screws.
3. Disconnect the MAP sensor electrical connector.
4. Disconnect the MAP inlet vacuum hose.
5. Remove the MAP sensor from the bracket.

INSTALLATION PROCEDURE
1. Install the MAP sensor to the bracket.
2. Connect the MAP inlet vacuum hose.
3. Connect the MAP sensor electrical connector.

NOTE: Refer to Fastener Notice in Service Precautions.

4. Install the bolts/screws.

Tighten
Tighten the bolts arid screws to 3 N.m (27 lb in).
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 1
Chevrolet Venture V6-3.4L VIN E 439
Manifold Absolute Pressure (MAP) Sensor: Description and Operation
The Manifold Absolute Pressure (MAP) sensor responds to changes in intake manifold pressure (vacuum). The MAP sensor signal voltage to the
PCM varies from below 2 volts at idle (high vacuum) to above 4 volts with the key ON and the engine not running or at wide open throttle (low
vacuum).

The MAP sensor is used to determine manifold pressure changes while the linear EGR flow test diagnostic is being run (Refer to DTC P0401
Exhaust Gas Recirculation (EGR) Flow Insufficient ),to determine engine vacuum level for other diagnostics, and to determine Barometric
Pressure (BARO).

If the PCM detects a voltage that is lower than the possible range of the MAP sensor, DTC P0107 Manifold Absolute Pressure (MAP) Sensor
Circuit Low Voltage is set. A signal voltage higher than the possible range of the sensor sets DTC P0108 Manifold Absolute Pressure (MAP)
Sensor Circuit High Voltage. An intermittent low or high voltage sets DTC P1107 Manifold Absolute Pressure (MAP) Sensor Circuit Intermittent
Low Voltage or DTC P1106 Manifold Absolute Pressure (MAP) Sensor Circuit Intermittent High Voltage respectively. The PCM can also detect a
shifted MAP sensor. The PCM compares the MAP sensor signal to a calculated MAP based on throttle position and various engine load factors
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 1
Chevrolet Venture V6-3.4L VIN E 440
Oxygen Sensor: Service and Repair
Heated Oxygen Sensor (HO2S) Replacement (HO2S1)

NOTE: Do not remove this pigtail from either the Heated Oxygen Sensor (HO2S) or the Oxygen Sensor (O2S). Removing the pigtail or the
connector will affect sensor operation.

Handle the oxygen sensor carefully. Do not drop the HO2S. keep the in-line electrical connector and the louvered end tree of grease, dirt, or other
contaminants. Do not use cleaning solvents of any type.

Do not repair the wiring, connector or terminals. Replace the oxygen sensor if the pigtail wiring, connector, or terminal is damaged.

This external clean air reference is obtained by way of the oxygen sensor signal and heater wires. Any attempt to repair the wires, connectors, or
terminals could result in the obstruction of the air reference and degraded sensor performance.

The following guidelines should be used when servicing the heated oxygen sensor:
^ Do not apply contact cleaner or other materials to the sensor or vehicle harness connectors. These materials may get into the sensor causing
poor performance.
^ Do not damage the sensor pigtail and harness wires in such a way that the wires inside are exposed. This could provide a path for foreign
materials to enter the sensor and cause performance problems.
^ Ensure the sensor or vehicle lead wires should not be bent sharply or kinked. Sharp bends or kinks could block the reference air path through
the lead wire.
^ Do not remove or defeat the oxygen sensor ground wire (where applicable). Vehicles that utilize the ground wired sensor may rely on this
ground as the only ground contact to the sensor. Removal of the ground wire will cause poor engine performance.
^ Ensure that the peripheral seal remains intact on the vehicle harness connector in order to prevent damage due to water intrusion. The engine
harness may be repaired using Packard's Crimp and Splice Seals Terminal Repair Kit. Under no circumstances should repairs be soldered
since this could result in the air reference being obstructed.

REMOVAL PROCEDURE
The heated oxygen sensor may be difficult to remove when engine temperature is below 48°C (120°F). Excessive force may damage threads in
exhaust manifold or exhaust pipe.

1. Turn OFF the ignition.


2. Disconnect the sensor electrical connector.

IMPORTANT: A special anti seize compound is used on the heated oxygen sensor threads. The compound consists of graphite suspended in
fluid and glass beads. The graphite will burn away, but the glass beads will remain, making the sensor easier to remove. New or service sensors
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 2
Chevrolet Venture V6-3.4L VIN E 441
will already have the compound applied to the threads. If a sensor is removed from an engine and if for any reason is to be reinstalled, the threads
must have anti seize compound applied before reinstallation.

3. Use the J 39194-B heated oxygen sensor wrench in order to carefully back out the heated oxygen sensor.

INSTALLATION PROCEDURE
1. Coat the threads of heated oxygen sensor/catalyst monitor with anti seize compound GM P/N 5613695, or equivalent if necessary.

NOTE: Refer to Fastener Notice in Service Precautions.

2. Install the heated oxygen sensor.

Tighten
Tighten the HO2S 1 (pre-catalytic converter) to 42 ± 4 N.m (31 lb ft).

3. Connect the sensor electrical connector.


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 1
Chevrolet Venture V6-3.4L VIN E 442
Oxygen Sensor: Service and Repair
Heated Oxygen Sensor (HO2S) Replacement (HO2S2)

NOTE: Do not remove this pigtail from either the Heated Oxygen Sensor (HO2S) or the Oxygen Sensor (O2S). Removing the pigtail or the
connector will affect sensor operation.

Handle the oxygen sensor carefully. Do not drop the HO2S. Keep the in-line electrical connector and the louvered end free of grease, dirt, or other
contaminants. Do not use cleaning solvents of any type.

Do not repair the wiring, connector or terminals. Replace the oxygen sensor if the pigtail wiring, connector, or terminal is damaged.

This external clean air reference is obtained by way of the oxygen sensor signal and heater wires. Any attempt to repair the wires, connectors, or
terminals could result in the obstruction of the air reference and degraded sensor performance.

The following guidelines should be used when servicing the heated oxygen sensor:
^ Do not apply contact cleaner or other materials to the sensor or vehicle harness connectors. These materials may get into the sensor causing
poor performance.
^ Do not damage the sensor pigtail and harness wires in such a way that the wires inside are exposed. This could provide a path for foreign
materials to enter the sensor and cause performance problems.
^ Ensure the sensor or vehicle lead wires should not be bent sharply or kinked. Sharp bends or kinks could block the reference air path through
the lead wire.
^ Do not remove or defeat the oxygen sensor ground wire (where applicable). Vehicles that utilize the ground wired sensor may rely on this
ground as the only ground contact to the sensor. Removal of the ground wire will cause poor engine performance.
^ Ensure that the peripheral seal remains intact on the vehicle harness connector in order to prevent damage due to water intrusion. The engine
harness may be repaired using Packard's Crimp and Splice Seals Terminal Repair Kit. Under no circumstances should repairs be soldered
since this could result in the air reference being obstructed.

REMOVAL PROCEDURE
The heated oxygen sensor may be difficult to remove when engine temperature is below 48°C (120°F). Excessive force may damage threads in
the exhaust pipe.

1. Turn OFF the ignition.


2. Raise the vehicle.
3. Disconnect the sensor electrical connector.

IMPORTANT: A special anti seize compound is used on the heated oxygen sensor threads. The compound consists of graphite suspended in
fluid and glass beads. The graphite will burn away, but the glass beads will remain, making the sensor easier to remove. New or service sensors
will already have the compound applied to the threads. If a sensor is removed from an engine and if for any reason is to be reinstalled, the threads
must have anti seize compound applied before reinstallation.

4. Use the J 39194-B heated oxygen wrench in order to carefully back out the heated oxygen sensor.

INSTALLATION PROCEDURE
1. Coat the threads of heated oxygen sensor/catalyst monitor with anti seize compound GM P/N #5613695, or equivalent if necessary.
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 2
Chevrolet Venture V6-3.4L VIN E 443

NOTE: Refer to Fastener Notice in Service Precautions.

2. Install the HO2S2.

Tighten
Tighten the HO2S 2 (post-catalytic converter) to 42±14 N.m (31 lb ft).

3. Connect the sensor electrical connector.


4. Lower the vehicle.
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 1
Chevrolet Venture V6-3.4L VIN E 444
Transmission Position Switch/Sensor: Adjustments
^ Tools Required
- J 41545 Park/Neutral Switch Alignment Tool

If a new PNP switch has been rotated and the pin is broken or if you are installing an old PNP switch, adjust the PNP switch.
1. Place the shift selector shaft into Neutral.
2. Use the J 41545 in order to align the slots of the PNP switch to the Neutral position.
3. Align the flats of the shift shaft to the flats in the PNP switch.
4. Install the PNP switch to the transaxle.

Important: If the PNP switch bolt holes do not align with the threaded holes in the transaxle, verify that the shaft is in the Neutral position.

5. Assemble the PNP switch bolts loosely.

6. Use the J 41545 in order to align the PNP switch.

Notice: Refer to Fastener Notice in Service Precautions.

7. Install the PNP switch bolts/screws.


^ Tighten the PNP switch bolts/screws to 25 Nm (18 ft. lbs.).
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 1
Chevrolet Venture V6-3.4L VIN E 445
Transmission Position Switch/Sensor: Service and Repair
Removal Procedure

1. Apply the parking brake.


2. Block the wheels.
3. Shift the transmission into Neutral.
4. Remove the throttle body air inlet duct. Refer to Air Cleaner Assembly Replacement in Powertrain Management.
5. Use a flat-bladed tool in order to remove the automatic transaxle range selector cable from the cable lever.

6. Disconnect the electrical connectors.


7. Remove the automatic transaxle range selector lever. Refer to Automatic Transmission Range Selector Cable Lever Replacement.

8. Remove the PNP switch bolts.


9. Remove the PNP switch.

Installation Procedure

Tool Required
- J 41545 Park/Neutral Switch Alignment Tool
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 2
Chevrolet Venture V6-3.4L VIN E 446

1. Verify that the shift shaft in the Neutral position.

Important: DO NOT ROTATE A NEW PNP SWITCH. A new PNP switch is produced in the Neutral position. If the bolt holes do not align
with the holes in the transaxle, verify that the transmission is in Neutral.

Adjust the PNP switch if the new switch has been rotated and the pin is broken or if using an old PNP switch. Refer to PNP Switch Adjustment.

2. Align the flats of the shift shaft to the flats in the PNP switch.
3. Install the PNP switch to the transaxle.

Notice: Refer to Fastener Notice in Service Precautions.

4. Install the PNP switch bolts.


^ Tighten the PNP switch bolts to 25 Nm (18 ft. lbs.).
5. Install the automatic transaxle range selector lever. Refer to Automatic Transmission Range Selector Cable Lever Replacement.

6. Connect the electrical connectors.

7. Install the automatic transaxle range selector cable.

Important: Verify that the engine starts ONLY with the transmission in Park or Neutral. Adjust as necessary. Refer to PNP Switch
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 3
Chevrolet Venture V6-3.4L VIN E 447
Adjustment.

8. Install the throttle body air inlet duct. Refer to Air Cleaner Assembly Replacement in Powertrain Management.
9. Remove the blocks from the wheels.
10. Release the parking brake.
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 1
Chevrolet Venture V6-3.4L VIN E 448
Vehicle Speed Sensor: Service and Repair
Removal Procedure

1. Raise and support the vehicle. Refer to Vehicle Lifting.


2. Remove the right front tire and wheel.
3. Remove the right engine splash shield.
4. Disconnect the vehicle speed sensor wiring harness connector.

5. Remove the vehicle speed sensor bolt (9).


6. Remove the vehicle speed sensor (10) from the extension case.

7. Remove the O-ring seal (11) from the vehicle speed sensor (10).

Important: Handle the vehicle speed sensor (10) carefully.

8. Inspect the vehicle speed sensor and O-ring seal for the following:
^ Damaged connector
^ Cracked housing
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 2
Chevrolet Venture V6-3.4L VIN E 449
^ Signs of rotor damage
^ Cuts or nicks on the O-ring seal (11)

Installation Procedure

1. Install the O-ring seal (11) to the vehicle speed sensor (10).
2. Install the vehicle speed sensor to the extension case.

Notice: Refer to Fastener Notice in Service Precautions.

3. Install the vehicle speed sensor bolt (9).


^ Tighten the vehicle speed sensor bolt to 12 Nm (106 inch lbs.).

4. Connect the vehicle speed sensor wiring harness connector.


5. Install the right engine splash shield.
6. Install the right front tire and wheel.
7. Lower the vehicle.
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 1
Chevrolet Venture V6-3.4L VIN E 450
Vehicle: Specifications
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 2
Chevrolet Venture V6-3.4L VIN E 451

GM Part Number 19001810


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 3
Chevrolet Venture V6-3.4L VIN E 452
Test Load 300 A

Cold Cranking Amperes 600 A

Reserve Capacity Rating 115 Minutes

Replacement Battery Number 78-6YR

Divide the reserve capacity by 4. The current drain in milliamps should not be more than this number.

Current draw Less than 25 milliamps is acceptable

Generator Model BOSCH NCB1

Rated Output 125 A

Load Test Output 87.5 A

Generator Model BOSCH KCB2

Rated Output 105 A

Load Test Output 70 A

Voltage
Voltage

Charging Voltage 13-16 Volts

Generator Model BOSCH NCB1

Rated Output 125 A

Load Test Output 87.5 A

Generator Model BOSCH KCB2

Rated Output 105 A

Load Test Output 70 A

Voltage
Voltage

Charging Voltage 13-16 Volts


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 4
Chevrolet Venture V6-3.4L VIN E 453

Temperature vs Resistance

Voltage
Voltage
ECT between 50-95 degrees F (10-35 degrees C)

Injector Voltage Reading 5.7 - 6.6 Volts


Please refer to Fuel Injector Coil Test procedure.

Resistance Ohms
Resistance Ohms
ECT between 50 - 95 degrees F (10 - 35 degrees C)

Ohms 11.4-12.6

Ignition Coil
Coil Resistance across leads ...................................................................................................................................................................... 5k-8k Ohms.
Ignition Timing
Information not supplied by the manufacturer.

A/C Compressor Hose Block Fitting to Accumulator Bolt 16 Nm

Accumulator Strap Bolt 5.5 Nm

Inflatable Restraint IP Module Fasteners 10 Nm

Inflatable Restraint Side Impact Sensor (SIS) Fasteners 10 Nm

Inflatable Restraint Sensing And Diagnostic Module (SDM) Fasteners 10 Nm


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 5
Chevrolet Venture V6-3.4L VIN E 454

Air Inlet Valve Electric Actuator Screws 1.6 Nm

Temperature Valve Electric Actuator Screws 1.6 Nm

Center Air Distribution Duct Retaining Nuts 10 Nm

Trim Hieght Specifications Non-Cargo Van D 5.47-6.25 in

J 9.21-10.00 in
(1) J Measurement taken 604 mm (24 inch) from
the centerline of the FRONT wheel.

K 10.07-10.86 in
(2) K Measurement taken 560 mm (22 inch) from
the centerline of the REAR wheel.

Z 2.28-3.07 in

Cargo Van (Z10) WITH Automatic D 5.78-6.57 in


Level Control (G67)

J 9.29-10.07 in
(1) J Measurement taken 604 mm (24 inch) from
the centerline of the FRONT wheel.

K 10.35-11.14 in
(2) K Measurement taken 560 mm (22 inch) from
the centerline of the REAR wheel.

Z 2.28-3.07 in

Cargo Van (Z10) WITHOUT D 6.53-7.32 in


Automatic Level Control (G67)

J 9.44-10.23 in
(1) J Measurement taken 604 mm (24 inch) from
the centerline of the FRONT wheel.

K 10.98-11.77 in
(2) K Measurement taken 560 mm (22 inch) from
the centerline of the REAR wheel.

Z 2.28-3.07 in

Front Camber Service Allowed (Acceptable) -1.20 to -0.20 deg

Service Preferred (Target) -0.70 deg

Caster (Nominal - No Means of Service Allowed (Acceptable) 2.40 to 3.40 deg


Adjustment Provided)

Service Preferred (Target) 2.90 deg

Cross Camber Service Allowed (Acceptable) -0.75 to 0.75 deg

Service Preferred (Target) 0 deg

Cross Caster (Nominal - No Service Allowed (Acceptable) -0.75 to 0.75 deg


Means of Adjustment Provided)
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 6
Chevrolet Venture V6-3.4L VIN E 455
Service Preferred (Target) 0 deg

Total Toe Service Allowed (Acceptable) -0.20 to 0.20 deg

Service Preferred (Target) 0 deg

Rear (Nominal - No Means of Camber Service Allowed (Acceptable) -0.75 to -1.25 deg
Adjustment Provided)

Service Preferred (Target) -1.0 deg

Cross Camber Service Allowed (Acceptable) -0.50 to 0.50 deg

Service Preferred (Target) 0 deg

Total Toe Service Allowed (Acceptable) -0.30 to 0.30 deg

Service Preferred (Target) 0 deg

Trim Height Specifications Vehicles with 205/70R15 Tires D 5.23-6.02 in

J 8.97-9.76 in
(1) J Measurement taken 604 mm (24 inch) from
the centerline of the FRONT wheel.

K 9.84-10.62 in
(2) K Measurement taken 560 mm (22 inch) from
the centerline of the REAR wheel.

Z 2.28-3.07 in

Vehicles with 215/70R15 Tires D 5.23-6.02 in

J 9.25-10.03 in
(1) J Measurement taken 604 mm (24 inch) from
the centerline of the FRONT wheel.

K 10.15-10.94 in
(2) K Measurement taken 560 mm (22 inch) from
the centerline of the REAR wheel.

Z 2.28-3.07 in

Front Camber Service Allowed (Acceptable) -1.20 to -0.20 deg

Service Preferred (Target) -0.70 deg

Caster (Nominal- No Means of Service Allowed (Acceptable) 2.40 to 3.40 deg


Adjustment Provided)

Service Preferred (Target) 2.90 deg

Cross Caster Service Allowed (Acceptable) -0.75 to 0.75 deg

Service Preferred (Target) 0 deg

Cross Caster (Nominal- No Means of Service Allowed (Acceptable) -0.75 to 0.75 deg
Adjustment Provided)

Service Preferred (Target) 0 deg

Total Toe Service Allowed (Acceptable) -0.20 to 0.20 deg

Service Preferred (Target) 0 deg

Rear (Nominal- No Means of Camber Service Allowed (Acceptable) -0.75 to -1.25 deg
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 7
Chevrolet Venture V6-3.4L VIN E 456
Adjustment Provided)

Cross Camber Service Preferred (Target) -1.0 deg

Total Toe Service Allowed (Acceptable) -0.50 to 0.50 deg

Service Preferred (Target) 0 deg

Service Allowed (Acceptable) -0.30 to 0.30 deg

Service Preferred (Target) 0 deg

Trim Height Specifications Non-Cargo Van D 5.47-6.25 in

J 9.21-10.00 in
(1) J Measurement taken 604 mm (24 inch) from the
centerline of the FRONT wheel.

K 10.07-10.86 in
(2) K Measurement taken 560 mm (22 inch) from the
centerline of the REAR wheel.

Z 2.28-3.07 in

Cargo Van (Z10) WITH Automatic Level Control D 5.78-6.57 in


(G67)

J 9.29-10.07 in
(1) J Measurement taken 604 mm (24 inch) from the
centerline of the FRONT wheel.

K 10.35-11.14 in
(2) K Measurement taken 560 mm (22 inch) from the
centerline of the REAR wheel.

Z 2.28-3.07 in

Cargo Van (Z10) WITHOUT Automatic Level D 6.53-7.32 in


Control (G67)

J 9.44-10.23 in
(1) J Measurement taken 604 mm (24 inch) from the
centerline of the FRONT wheel.

K 10.98-11.77 in
(2) K Measurement taken 560 mm (22 inch) from the
centerline of the REAR wheel.

Z 2.28-3.07 in

Trim Height Specifications Vehicles with 205/70R15 Tires D 5.23-6.02 in

J 8.97-9.76 in
(1) J Measurement taken 604 mm (24 inch) from the
centerline of the FRONT wheel.

K 9.84-10.62 in
(2) K Measurement taken 560 mm (22 inch) from the
centerline of the REAR wheel.

Z 2.28-3.07 in

Vehicles with 215/70R15 Tires D 5.23-6.02 in


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 8
Chevrolet Venture V6-3.4L VIN E 457

J 9.25-10.03 in
(1) J Measurement taken 604 mm (24 inch) from the
centerline of the FRONT wheel.

K 10.15-10.94 in
(2) K Measurement taken 560 mm (22 inch) from the
centerline of the REAR wheel.

Z 2.28-3.07 in

Generator B+ Terminal Nut 13 Nm

Generator Bolt 50 Nm

Generator Bracket Bolt 50 Nm

Generator Rear Cover Nut 12 Nm

Generator Rear Cover Screw 4 Nm

Generator Voltage Regulator Retaining Screw 2 Nm

Generator Voltage Regulator Terminal Screw 1 Nm

Antenna Cable Extension to Roof Bolt/Screw 3.2 Nm

Oil Pan to Case 10 ft.lb

Flywheel Bolts 52 lb. ft.

Fastener Tightening Specifications


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 9
Chevrolet Venture V6-3.4L VIN E 458

Part 1 of 2

Part 2 of 2
Transmission General Specifications
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 10
Chevrolet Venture V6-3.4L VIN E 459

Part 1 of 2

Part 2 of 2
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 11
Chevrolet Venture V6-3.4L VIN E 460

General
Bolt/Screw, Automatic Transaxle Case Extension M10 x 1.5 x 35 (Qty 4) ...................................................................................... 36 Nm (26 ft. lbs.)
Stud/Screw, Vehicle Speed Sensor - M8 x 1.25 x 12 (Qty 1) ...................................................................................................... 12 Nm (106 inch lbs.)
Bolt/Screw, Forward Band Servo Cover - M6 x 1.0 x 20 (Qty 3) ............................................................................................... 12 Nm (106 inch lbs.)
Bolt, Oil Pan Nm 6 x 1.0 x 17 (Qty 20) ............................................................................................................................................. 14 Nm (10 ft. lbs.)
Fitting, Transaxle Oil Cooler Pipe - 1/4 - 18 NPSF (Qty 2) .............................................................................................................. 38 Nm (28 ft. lbs.)
Plug, Automatic Transaxle Oil Pressure Test Hole 1/8 - 27 NPTF (Qty 1) ................................................................................. 12 Nm (106 inch lbs.)
Bolt/Screw, Case Side Cover (Flange) - M8 x 1.25 x 25 (Qty 9) ...................................................................................................... 25 Nm (18 ft. lbs.)
Bolt/Screw, Case Side Cover (Torx(R) Special) - M8 x 1.25 x 21 (Qty 4) ...................................................................................... 25 Nm (18 ft. lbs.)
Bolt/Screw, Case Side Cover (stud) - M8 x 1.25 x 24 (Qty 4) .......................................................................................................... 25 Nm (18 ft. lbs.)
Bolt/Screw, Manual 2-1 Band Servo Cover - M8 x 1.25 x 25 (Qty 3) .............................................................................................. 25 Nm (18 ft. lbs.)
Bolt/Screw, Accumulator Cover - M6 x 1.0 x 28 (Qty 11) .......................................................................................................... 12 Nm (106 inch lbs.)
Bolt/Screw, Automatic Transaxle Oil Pump Cover M6 x 1.0 x 20 (Qty 1) ..................................................................................... 8 Nm (70 inch lbs.)
Bolt/Screw, Automatic Transaxle Oil Pump - M6 x 1.0 x 95 (Qty 2) ............................................................................................... 16 Nm (11 ft. lbs.)
Bolt/Screw, Automatic Transaxle Oil Pump - M6 x 1.0 x 85 (Qty 9) ......................................................................................... 12 Nm (106 inch lbs.)
Bolt/Screw, Control Valve Body - M6 x 1.0 x 65 (Qty 3) .......................................................................................................... 12 Nm 106 inch lbs.)
Bolt/Screw, Control Valve Body - M6 x 1.0 x 60 (Qty 3) ........................................................................................................... 12 Nm (106 inch lbs.)
Bolt/Screw, Control Valve Body - M6 x 1.0 x 30 (Qty 1) ........................................................................................................... 12 Nm (106 inch lbs.)
Bolt/Screw, Control Valve Body (Torx(R)) - M6 x 1.0 x 45 (Qty 2) .......................................................................................... 12 Nm (106 inch lbs.)
Bolt/Screw, Control Valve Body - M6 x 1.0 x 55 (Qty 3) ........................................................................................................... 12 Nm (106 inch lbs.)
Bolt/Screw, Control Valve Body - M6 x 1.0 x 95 (Qty 1) ................................................................................................................ 16 Nm (11 ft. lbs.)
Bolt/Screw, Control Valve Body - M8 x 1.25 x 90 (Qty 1) .............................................................................................................. 25 Nm (18 ft. lbs.)
Bolt/Screw, Control Valve Body - M6 x 1.0 x 20 (Qty 2) ............................................................................................................... 8 Nm (70 inch lbs.)
Bolt/Screw, Control Valve Body - M6 x 1.0 x 85 (Qty 1) ........................................................................................................... 12 Nm (106 inch lbs.)
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 12
Chevrolet Venture V6-3.4L VIN E 461
Bolt/Screw, Automatic Transaxle Case Cover (Torx(R) Special) M6 x 1.0 x 32 (Qty 1) ........................................................... 12 Nm (106 inch lbs.)
Bolt/Screw, Automatic Transaxle Case Cover - M6 x 1.0 x 40 (Qty 3) ...................................................................................... 12 Nm (106 inch lbs.)
Bolt/Screw, Automatic Transaxle Case Cover - M8 x 1.25 x 50 (Qty 3) .......................................................................................... 25 Nm (18 ft. lbs.)
Bolt/Screw, Automatic Transaxle Case Cover - M6 x 1.0 x 30 (Qty 3) ...................................................................................... 12 Nm (106 inch lbs.)
Bolt/Screw, Drive Sprocket Support - M8 x 1.25 x 24 (Qty 4) ......................................................................................................... 25 Nm (18 ft. lbs.)
Nut, Manual Shift Shaft Detent Lever - M 10 x 1.5 (Qty 1) ............................................................................................................. 32 Nm (23 ft. lbs.)
Bolt/Screw, Manual Shift Shaft Detent - M6 x 1.0 x 16 (Qty 1) ................................................................................................. 12 Nm (106 inch lbs.)

General
ID Number I Dimension (mm) Dimension (inch) Color
Differential Carrier/Case Thrust Washer (714) Selection Guide
1 ..................................................................................................................................................................... 1.40-1.50 mm (0.055-0.059 inch) Orange
2 ....................................................................................................................................................................... 1.50-1.60 mm (0.059-0.062 inch) White
3 ......................................................................................................................................................................... 1.60-1.70 mm (0.062-0.066 inch) Blue
4 ......................................................................................................................................................................... 1.70-1.80 mm (0.066-0.070 inch) Pink
5 ..................................................................................................................................................................... 1.80-1.90 mm (0.070-0.074 inch) Brown
6 ....................................................................................................................................................................... 1.90-2.00 mm (0.074-0.078 inch) Green
7 ....................................................................................................................................................................... 2.00-2.10 mm (0.078-0.082 inch) Black
8 ...................................................................................................................................................................... 2.10-2.20 mm (0.082-0.086 inch) Purple
9 ........................................................................................................................................................... 2.20-2.30 mm (0.086-0.091 inch) Purple/White
10 ........................................................................................................................................................... 2.30-2.40 mm (0.091-0.095 inch) Purple/Blue
Bearing/input Clutch Hub Selective Thrust Washer (630) Selection Guide
1 .......................................................................................................................................................... 2.90-3.00 mm (0.114-0.118 inch) Orange/Green
2 .......................................................................................................................................................... 3.05-3.15 mm (0.120-0.124 inch) Orange/Black
3 ................................................................................................................................................................. 3.20-3.30 mm (0.126-0.130 inch) No Color
4 ....................................................................................................................................................................... 3.35-3.45 mm (0.132-0.136 inch) White
5 ......................................................................................................................................................................... 3.50-3.60 mm (0.138-0.142 inch) Blue
6 ......................................................................................................................................................................... 3.65-3.75 mm (0.144-0.148 inch) Pink
7 ..................................................................................................................................................................... 3.80-3.90 mm (0.150-0.154 inch) Brown
8 ....................................................................................................................................................................... 3.95-4.05 mm (0.156-0.159 inch) Green
9 ....................................................................................................................................................................... 4.10-4.20 mm (0.161-0.165 inch) Black
10 .................................................................................................................................................................... 4.25-4.35 mm (0.167-0.171 inch) Purple
11 ......................................................................................................................................................... 4.40-4.50 mm (0.173-0.177 inch) Purple/White

General
Important:
^ Rotor, vanes and slide must be chosen from the same size classification as the oil pump body.
^ Allowable rotor, vane and slide to oil pump body end play is as follows:
^ Slide to Oil Pump Body End Play - 0.033-0.076 mm (0.0013-0.0030 inch)
^ Rotor and Vane to Oil Pump Body End Play 0.050-0.083 mm (0.0020-0.0033 inch)

The oil pump assembly has a selective rotor, vane and slide components. These components are chosen based on pump body dimensions. Oil pump b

Rotor Selection
1 ..................................................................................................................................................................... 17.953-17.963 mm (0.7068-0.7072 inch)
2 ..................................................................................................................................................................... 17.963-17.973 mm (0.7072-0.7076 inch)
3 ..................................................................................................................................................................... 17.973-17.983 mm (0.7076-0.7080 inch)
4 ..................................................................................................................................................................... 17.983-17.993 mm (0.7080-0.7084 inch)

Size
Classification Thickness (mm) Thickness (inch)
Vane Selection
1 ..................................................................................................................................................................... 17.943-17.961 mm (0.7064-0.7071 inch)
2 ..................................................................................................................................................................... 17.943-17.961 mm (0.7064-0.7071 inch)
3 ..................................................................................................................................................................... 17.961-17.979 mm (0.7071-0.7078 inch)
4 ..................................................................................................................................................................... 17.961-17.979 mm (0.7071-0.7078 inch)
Slide Selection
1 ..................................................................................................................................................................... 17.957-17.967 mm (0.7070-0.7074 inch)
2 ..................................................................................................................................................................... 17.967-17.977 mm (0.7074-0.7078 inch)
3 ..................................................................................................................................................................... 17.977-17.987 mm (0.7078-0.7081 inch)
4 ..................................................................................................................................................................... 17.987-17.997 mm (0.7081-0.7085 inch)
Oil Pump Body Depth
1 ..................................................................................................................................................................... 18.000-18.010 mm (0.7087-0.7091 inch)
2 ..................................................................................................................................................................... 18.010-18.020 mm (0.7091-0.7094 inch)
3 ..................................................................................................................................................................... 18.020-17.030 mm (0.7094-0.7098 inch)
4 ..................................................................................................................................................................... 18.030-18.040 mm (0.7098-0.7102 inch)
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 13
Chevrolet Venture V6-3.4L VIN E 462

General
RPO Codes ........................................................................................................................................................................................... M15/MN3/MN7
Production Location ..................................................................................................................................................................................... Warren, MI
Vehicle Platform (Engine/Transmission) Usage ...................................................................................................................................... C, H, W, G, U
Transaxle Drive ............................................................................................................................................... Transverse Mounted Front Wheel Drive
1st Gear Ratio ...................................................................................................................................................................................................... 2.921:1
2nd Gear Ratio .................................................................................................................................................................................................... 1.568:1
3rd Gear Ratio ..................................................................................................................................................................................................... 1.000:1
4th Gear Ratio ..................................................................................................................................................................................................... 0.705:1
Reverse ................................................................................................................................................................................................................ 2.385:1
Torque Converter Size (Diameter of Torque Converter Turbine) .................................................................... 245 mm (M 15) 258 mm (MN3/MN7)
Pressure Taps ............................................................................................................................................................................................. Line Pressure
Transaxle Fluid Type ............................................................................................................................................................................ Dexron(TM) III
Transaxle Fluid Capacity (Approximate) ................. Bottom Pan Removal: 7.0L (7.4 qts) Complete Overhaul: 9.5L (10.0 qts) Dry: 12.7L (13.4 qts)
Transaxle Type: 4 ........................................................................................................................................................................... Four Forward Gears
Transaxle Type: T .............................................................................................................................................................................. Transverse Mount
Transaxle Type: 65 ................................................................................................................................................................................... Product Series
Transaxle Type: E ............................................................................................................................................................................ Electronic Controls
Chain Ratios (Designates Number of Teeth on the Drive/Driven Sprockets) ............................................................................................. 35/35 37/33
Final Drive Ratios .................................................................................................................................................................................. 2.86, 3.05, 3.29
Overall Final Drive Ratios ............................................................................................................................................................ 2.86, 3.05, 2.93, 3.29
Position Quadrant .............................................................................................................................................. P, R, N, D, 3, 2, 1 or P, R, N, OD, 2, 1
Case Material ................................................................................................................................................................................... Die Cast Aluminum
Transaxle Weight Dry ..................................................................................................................................................................... 87.9 kg (194.2 lbs)
Transaxle Weight Wet .................................................................................................................................................................... 97.0 kg (214.4 lbs)
Maximum Trailer Towing Capacity .................................................................................................................................................. 907 kg (2000 lbs)
Maximum Gross Vehicle Weight (GVW) ..................................................................................................................................... 2903 kg (6,400 lbs)
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 14
Chevrolet Venture V6-3.4L VIN E 463
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 15
Chevrolet Venture V6-3.4L VIN E 464

Accumulator, A/T
Accumulator Cover to Case ......................................................................................................................................................................... 106 inch lbs

Fluid Filler Tube Bolt 115 in.lb

Fluid Filler Tube Nut 115 in.lb

2-1 Servo to Case 18 ft.lb

Forward Band Servo Cover to Case 106 in.lb

Tightening Specifications
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 16
Chevrolet Venture V6-3.4L VIN E 465
Tightening Specifications

Case Cover to Case 106 in.lb

Case Cover to Driven Sprocket Support 18 ft.lb

Case Cover to Driven Sprocket Support (Torx) 106 in.lb

Case Side Cover to Case 18 ft.lb

Case Side Cover to Case (Stud) 18 ft.lb

Case Side Cover to Case (Torx Special) 18 ft.lb

Detent Spring to Case Cover 106 in.lb

Pump Cover to Case Cover 106 in.lb

TFP Switch to Case Cover 106 in.lb

Case Extension to Case 26 ft.lb

Oil Cooler Hose Clip Bolt 17 ft.lb

Oil Cooler Pipe Fitting at Radiator 33 ft.lb

Oil Pan to Case 10 ft.lb

Pump Cover to Pump Body 70 in.lb

Flywheel to Torque Converter Bolts 47 ft.lb

Torque Converter Cover Bolts 89 in.lb

Oil Cooler Quick Connector 28 ft.lb

Oil Cooler Quick Connector with Checkball 28 ft.lb

PNP Switch Bolts 18 ft.lb

Transmission Pressure Test Port, A/T


Oil Pressure Test Hole Plug ......................................................................................................................................................................... 106 inch lbs
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 17
Chevrolet Venture V6-3.4L VIN E 466

TFP Switch to Valve Body 70 in.lb

Valve Body to Case 106 in.lb

Valve Body to Case 106 in.lb

Valve Body to Case Cover 106 in.lb

Valve Body to Case Cover 106 in.lb

Valve Body to Case Cover (Torx) 106 in.lb

Valve Body to Driven Sprocket Support 18 ft.lb

Battery Hold-Down Retainer Bolt 25 Nm

Battery Terminal Bolt 16 Nm

Battery Tray Bolt 10 Nm

Battery Ground (Negative) Cable Nut to Transaxle Stud 25 Nm

Battery Ground (Negative) Cable to Inner Fender Bolt 5 Nm

Battery Positive Cable to Underhood Electrical Center Nut 10 Nm

Blower Motor Screws 20 Nm

Blower Motor Resistor/Relay Screws 1.9 Nm

Body Front End


Fastener Tightening Specifications
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 18
Chevrolet Venture V6-3.4L VIN E 467

Body Rear End


Fastener Tightening Specifications

Bumper
Fastener Tightening Specifications
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 19
Chevrolet Venture V6-3.4L VIN E 468

Doors
Fastener Tightening Specifications

Exterior Moulding / Trim


Fastener Tightening Specifications

Front Subframe
Fastener Tightening Specifications

Hood Release Handle Bolts/Screws 2 Nm

Instrument Panel, Gauges, and Console - Fastener Tightening Specifications


Fastener Tightening Specifications
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 20
Chevrolet Venture V6-3.4L VIN E 469

Interior Trim - Fastener Tightening Specifications


Fastener Tightening Specifications

Luggage Rack
Fastener Tightening Specifications

Rear Mirror Support Screw 2 Nm

Front Seat Nuts 40 Nm

Front Seat Recliner Bolts 48 Nm


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 21
Chevrolet Venture V6-3.4L VIN E 470

Rear Seat Riser Bolts (Bucket) 45 Nm

Rear Seat Riser Bolts (Split Benches) 32 Nm

Seat Adjuster Bolts 32 Nm

Seats - Fastener Tightening Specifications


Fastener Tightening Specifications

Liftgate Lock Cylinder Retaining Nuts 10 Nm

Liftgate Strut Ball Stud 25 Nm

Liftgate Strut Bracket to Liftgate Retaining Bolts 10 Nm

Lower Liftgate Wedge Retaining Screws 10 Nm

Upper Liftgate Wedge Retaining Screws 10 Nm

Liftgate Handle Retaining Bolts 10 Nm

Liftgate Handle Retaining Nuts 10 Nm

Liftgate Hinge Stud Nuts 25 Nm

Liftgate Hinge to Liftgate Retaining Bolts 25 Nm

Liftgate Latch Retaining Bolts 10 Nm

Liftgate Latch Striker Retaining Bolts 25 Nm

System Specifications
Front Brakes

Caliper Bore Diameter ........................................................................................................................................................................ 63.5 mm 2.500 in


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 22
Chevrolet Venture V6-3.4L VIN E 471
Rotor Diameter ................................................................................................................................................................................ 278.0 mm 10.945 in
Rotor Discard Thickness* ..................................................................................................................................................................... 30.7 mm 1.21 in
Rotor Maximum Lateral Runout ......................................................................................................................................................... 0.06 mm 0.002 in
Rotor Maximum Scoring .................................................................................................................................................................... 1.50 mm 0.059 in
Rotor Maximum Thickness Variation ............................................................................................................................................... 0.025 mm 0.001 in
Rotor Minimum Thickness After Refinish .......................................................................................................................................... 31.08 mm 1.22 in
Rotor Minimum Wear Stock ............................................................................................................................................................... 0.38 mm 0.015 in
Rotor Thickness - New ......................................................................................................................................................................... 32.2 mm 1.27 in

Rear Brakes

Caliper Bore Diameter ........................................................................................................................................................................ 38.1 mm 1.500 in


Rotor Diameter ................................................................................................................................................................................ 278.0 mm 10.945 in
Rotor Discard Thickness* ....................................................................................................................................................................... 9.0 mm 0.35 in
Rotor Maximum Lateral Runout ....................................................................................................................................................... 0.080 mm 0.003 in
Rotor Maximum Scoring .................................................................................................................................................................... 1.50 mm 0.059 in
Rotor Maximum Thickness Variation ............................................................................................................................................... 0.025 mm 0.001 in
Rotor Minimum Thickness After Refinish ............................................................................................................................................ 10.6 mm 0.41 in
Rotor Minimum Wear Stock ................................................................................................................................................................... 1.6 mm 0.06 in
Rotor Thickness (new) .......................................................................................................................................................................... 11.0 mm 0.43 in

* All brake rotors have a discard dimension cast into them. Replace any rotor that does not meet this specification. After refinishing the rotor, replace

The content of this article has been updated by manual update # 04-05-23-002A dated August 4, 2005 for Rotor Minimum Allowable Thickness Afte

Electronic Brake Control Module (EBCM) to Brake Pressure Modulator Valve (BPMV). 44 in.lb

Hydraulic Control Assembly - Antilock Brakes


ABS Modulator Bleeder Valves ......................................................................................................................................................... 9 Nm (80 inch lbs.)
Brake Pressure Modulator Valve (BPMV) and Electronic Brake Control Module (EBCM) Assembly to mounting bracket. ..... 10 Nm (89 inch lbs.)

TCS Modulator Bleeder Valves 80 in.lb

Brake System Pressure Bleed Initial Pressure Adjustment Setting (Leak Testing the Hydraulic Brake System) 10 psi

Pressure Bleed Procedure Setting 35 psi

Brake Pedal Brace Bolt 89 in.lb

Brake Pedal Brace Nut 89 in.lb

Brake Pedal Bracket Nut 44 in.lb

Brake Pedal Maximum Travel* 2.91 in


*Specification with 450 N (100 lbs.) of force applied to
the brake pedal, the ignition OFF and the brake booster
vacuum depleted.
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 23
Chevrolet Venture V6-3.4L VIN E 472

Disc Brake Component Specifications


Front Brakes

Caliper Bore Diameter ........................................................................................................................................................................ 63.5 mm 2.500 in


Rotor Diameter ................................................................................................................................................................................ 278.0 mm 10.945 in
Rotor Discard Thickness* ..................................................................................................................................................................... 30.7 mm 1.21 in
Rotor Maximum Lateral Runout ......................................................................................................................................................... 0.06 mm 0.002 in
Rotor Maximum Scoring .................................................................................................................................................................... 1.50 mm 0.059 in
Rotor Maximum Thickness Variation ............................................................................................................................................... 0.025 mm 0.001 in
Rotor Minimum Thickness After Refinish .......................................................................................................................................... 31.08 mm 1.22 in
Rotor Minimum Wear Stock ............................................................................................................................................................... 0.38 mm 0.015 in
Rotor Thickness - New ......................................................................................................................................................................... 32.2 mm 1.27 in

Rear Brakes

Caliper Bore Diameter ........................................................................................................................................................................ 38.1 mm 1.500 in


Rotor Diameter ................................................................................................................................................................................ 278.0 mm 10.945 in
Rotor Discard Thickness* ....................................................................................................................................................................... 9.0 mm 0.35 in
Rotor Maximum Lateral Runout ....................................................................................................................................................... 0.080 mm 0.003 in
Rotor Maximum Scoring .................................................................................................................................................................... 1.50 mm 0.059 in
Rotor Maximum Thickness Variation ............................................................................................................................................... 0.025 mm 0.001 in
Rotor Minimum Thickness After Refinish ............................................................................................................................................ 10.6 mm 0.41 in
Rotor Minimum Wear Stock ................................................................................................................................................................... 1.6 mm 0.06 in
Rotor Thickness (new) .......................................................................................................................................................................... 11.0 mm 0.43 in

* All brake rotors have a discard dimension cast into them. Replace any rotor that does not meet this specification. After refinishing the rotor, replace

The content of this article has been updated by manual update # 04-05-23-002A dated August 4, 2005 for Rotor Minimum Allowable Thickness Afte

Front Brakes Brake Caliper Bleeder Valve 115 in.lb

Brake Caliper Bolt 63 ft.lb

Brake Caliper Bracket Bolt 137 ft.lb

Caliper Bore Diameter 2.500 in

Rear Brakes (Export) Brake Caliper Bleeder Valve 62 in.lb

Brake Caliper Bolt 33 ft.lb

Brake Caliper Bracket Bolt 92 ft.lb

Caliper Bore Diameter 1.500 in

Brake Pad
Replace the pads when the thickness is worn to within 0.76 mm (0.030 inch) of the shoe. Replace all pads in axle sets.

Measure the flatness of the inner and outer pads. Place the pad surfaces together and measure the gap between the surfaces. If more than 0.13 mm (0

Brake Rotor/Disc
Front Brakes
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 24
Chevrolet Venture V6-3.4L VIN E 473
Caliper Bore Diameter ........................................................................................................................................................................ 63.5 mm 2.500 in
Rotor Diameter ................................................................................................................................................................................ 278.0 mm 10.945 in
Rotor Discard Thickness* ..................................................................................................................................................................... 30.7 mm 1.21 in
Rotor Maximum Lateral Runout ......................................................................................................................................................... 0.06 mm 0.002 in
Rotor Maximum Scoring .................................................................................................................................................................... 1.50 mm 0.059 in
Rotor Maximum Thickness Variation ............................................................................................................................................... 0.025 mm 0.001 in
Rotor Minimum Thickness After Refinish .......................................................................................................................................... 31.08 mm 1.22 in
Rotor Minimum Wear Stock ............................................................................................................................................................... 0.38 mm 0.015 in
Rotor Thickness - New ......................................................................................................................................................................... 32.2 mm 1.27 in

Rear Brakes

Caliper Bore Diameter ........................................................................................................................................................................ 38.1 mm 1.500 in


Rotor Diameter ................................................................................................................................................................................ 278.0 mm 10.945 in
Rotor Discard Thickness* ....................................................................................................................................................................... 9.0 mm 0.35 in
Rotor Maximum Lateral Runout ....................................................................................................................................................... 0.080 mm 0.003 in
Rotor Maximum Scoring .................................................................................................................................................................... 1.50 mm 0.059 in
Rotor Maximum Thickness Variation ............................................................................................................................................... 0.025 mm 0.001 in
Rotor Minimum Thickness After Refinish ............................................................................................................................................ 10.6 mm 0.41 in
Rotor Minimum Wear Stock ................................................................................................................................................................... 1.6 mm 0.06 in
Rotor Thickness (new) .......................................................................................................................................................................... 11.0 mm 0.43 in

* All brake rotors have a discard dimension cast into them. Replace any rotor that does not meet this specification. After refinishing the rotor, replace

The content of this article has been updated by manual update # 04-05-23-002A dated August 4, 2005 for Rotor Minimum Allowable Thickness Afte

Brake Shoe
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 25
Chevrolet Venture V6-3.4L VIN E 474
Minimum Linning Thickness ............................................................................................................................................................................ 0.030 in.
(Above Rivet Head or Backing Plate)

Brake Rear Wheel Cylinder Bleeder Valve 62 in.lb

Wheel Cylinder Bolts 110 in.lb

Brake Hose Bolt at Front Brake Caliper 40 ft.lb

Brake Hose Bolt at Rear Brake Caliper (Export Only) 32 ft.lb

Brake Pipe Fitting 15 ft.lb

Brake Pipe Fittings at Brake Pressure Modulator Valve (BPMV) and Master Cylinder. 18 ft.lb

Proportioning Valve Cap 20 ft.lb


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 26
Chevrolet Venture V6-3.4L VIN E 475

Parking Brake Cable


Park Brake Cable Clip Nut .............................................................................................................................................................. 3 Nm (27 inch lbs.)
Park Brake Cable Front Guide Bolt ............................................................................................................................................ 13 Nm (115 inch lbs.)
Park Brake Cable Rear Guide Nut .............................................................................................................................................. 14 Nm (124 inch lbs.)

gc00ubody_5-132a
gc00ubody_5-132a

Park Brake Lever Nuts 89 in.lb

Parking Brake Warning Switch


Park Brake Indicator Switch Screw ................................................................................................................................................. 3 Nm (27 inch lbs.)

Brake Booster Nut 18 ft.lb

Child Seat Tether Strap Anchor Bracket Bolt 43 Nm

Child Seat Tether Strap Anchor Plate Bolt And Nut 10 Nm

System Specifications
Compressor Mounting Bolts..........50 Nm 37 ft lb

Compressor Shaft Nut...............18 Nm 13 ft lb

Compressor Clutch
Compressor Clutch Gap
V5 Conventional Mount ..................................................................................................................................................................... 0.40 - 0.50 mm
V5 Direct Mount ........................................................................................................................................................................................... 0.40 mm

Heater A/C Controls Bolts/Screws 2.5 Nm


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 27
Chevrolet Venture V6-3.4L VIN E 476

Antifreeze GM Goodwrench DEX-CO0L (R) or HAVOLINE (R) DEX-COOL


(R)

Antifreeze to Water Ratio 56 %

Front HVAC System Only (C60) without Heavy Duty Cooling (V08 9.5 qt (US)

Front and Rear HVAC System (C34) without Heavy Duty Cooling 12.1 qt (US)
(V08)

Front HVAC System Only (C60) with Heavy Duty Cooling (VO8) 10.5 qt (US)

Front and Rear HVAC System (C34) with Heavy Duty Cooling (V08) 13.2 qt (US)

Coolant Recovery Reservoir 1 qt (US)

Thermostat Bypass Pipe to Cylinder Head Nut 18 ft.lb

Thermostat Bypass Pipe to Engine Front Cover Bolt 106 in.lb

Thermostat Bypass Pipe to Throttle Body Nut 18 ft.lb

Thermostat Bypass Pipe Bolt 98 in.lb

Thermostat Bypass Pipe Nut 18 ft.lb


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 28
Chevrolet Venture V6-3.4L VIN E 477

Cooling Fan Shroud Bolts 53 in.lb

Radiator Bracket Bolts 18 ft.lb

Radiator Lower Air Deflector Bolts 15 ft.lb

Cooling Fan Nut 53 in.lb

Cooling Fan Motor Screws 53 in.lb

Blade Diameter 14.1 in

Motor Type Generation II Low Profile Permanent Magnet

Water Outlet Bolt 18 ft.lb

Thermostat Housing Bolts 18 ft.lb

Water Pump Bolt 89 in.lb

Cruise Control Module Mounting Bracket to Inner Fender Bolts 6 Nm

Cruise Control Module to Mounting Bracket Bolt 6 Nm

Camshaft Sprocket Bolt 103 lb. ft.

Connecting Rod Bearing Cap Nut 15 ft.lb


+ 75 degrees

Water Pump Bolt 89 in.lb

Crankshaft Balancer Bolt 76 ft.lb

Cylinder Head Torque & Sequence


This article has been updated with TSB 02-06-01-003B, 4/15/08
This bulletin is being revised to include a Notice advising that the cylinder head bolts are NOT TO BE RE-USED. Please discard Corporate Bull

Notice: This component uses torque-to-yield bolts. When servicing this component, do not re-use the bolts. New torque-to-yield bolts must be ins
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 29
Chevrolet Venture V6-3.4L VIN E 478

Tighten the NEW cylinder head bolts to 60 Nm (44 lb ft) in the order shown. Use the J 36660-A torque angle meter in order to rotate the cylinder

Exhaust Manifold Nut 12 ft.lb

Exhaust Manifold Stud 13 ft.lb

Exhaust Manifold Pipe Nut 26 ft.lb

Fastener Tightening Specifications


Fastener Tightening Specifications
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 30
Chevrolet Venture V6-3.4L VIN E 479

Part 1 of 2
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 31
Chevrolet Venture V6-3.4L VIN E 480

Part 2 of 2

Flywheel Bolts 52 lb. ft.

General Engine Data/Specifications


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 32
Chevrolet Venture V6-3.4L VIN E 481
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 33
Chevrolet Venture V6-3.4L VIN E 482

Main Bearing Cap Bolts First Pass 37 lb. ft.

Final Pass +77 Degrees

Metric-English Conversion Factors


CONVERSION FACTORS
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 34
Chevrolet Venture V6-3.4L VIN E 483

Oil Pump Oil Pump Drive Clamp Bolt 27 ft.lb

Oil Pump Mounting Bolt 30 ft.lb

Gear Length 1.199-1.200 inch


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 35
Chevrolet Venture V6-3.4L VIN E 484
Diameter 1.498-1.500 inch

Side Clearance 0.001-0.003 in

End Clearance 0.002-0.005 in

Valve to Bore Clearance 0.0015-0.0035 in

Gear Lash 0.0037-0.0077 inch

Gear Pocket Depth 1.202-1.204 in

Gear Pocket Diameter 1.503-1.505 in

Camshaft Sprocket Bolt 103 lb. ft.

Camshaft Thrust Plate Screw 89 in.lb

Lobe Lift (intake and Exhaust) 0.2727 in

Journal Diameter 1.868-1.869 in

Journal Clearance 0.001-0.0039 in

Journal Runout - Max 0.001 in

Rod Bearing Journal Clearance 0.0007-0.0024 in

Rod Side Clearance 0.007-0.017 in

Rod Bearing Bore Diameter 2.124-2.125 in

Connecting Rod Bearing Cap Nut 15 ft.lb


+ 75 degrees

Connecting Rod Bearing Cap Nut 15 ft.lb


+ 75 degrees

Rod Bearing Journal Clearance 0.0007-0.0024 in

Rod Side Clearance 0.007-0.017 in

Rod Bearing Bore Diameter 2.124-2.125 in

Camshaft Sprocket Bolt 103 lb. ft.


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 36
Chevrolet Venture V6-3.4L VIN E 485

Crankshaft-Main Bearing Cap Bolt/Stud 37 ft.lb


+ 77 degrees

Crankshaft Oil Deflector Nut 18 ft.lb

Main Journal Diameter 2.6473-2.6483 in

Main Journal Taper 0.0002 in

Out Of Round - Max 0.0002 in

Flange Runout - Max 0.0016 in

Cylinder Block Main Bearing Bore Diameter 2.8407-2.8412 in

Crankshaft Main Bearing Inside Diameter 2.6492-2.6502 in

Main Bearing Clearance 0.0008-0.0025 in

Main Thrust Bearing Clearance 0.0012-0.0030 in

Crankshaft End Play 0.0024-0.0083 in

Crankshaft Flange Runout - Max 0.0016 in

Rod Bearing Journal Diameter 1.9987-1.9994 in

Rod Bearing Journal Taper - Max 0.0002 in

Rod Bearing Journal Out Of Round - Max 0.0002 in

Rod Inside Bearing Diameter 2.000-2.002 in

Diameter 3.6228-3.6235 in

Out Of Round Maximum 0.0003 in

Taper - Thrust Side Maximum 0.0004 in

General Engine Specifications


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 37
Chevrolet Venture V6-3.4L VIN E 486
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 38
Chevrolet Venture V6-3.4L VIN E 487

Main Bearing Cap Bolts First Pass 37 lb. ft.

Final Pass +77 Degrees

Cylinder Block Main Bearing Bore Diameter 2.8407-2.8412 in

Crankshaft Main Bearing Inside Diameter 2.6492-2.6502 in

Main Bearing Clearance 0.0008-0.0025 in

Main Thrust Bearing Clearance 0.0012-0.0030 in

Crankshaft End Play 0.0024-0.0083 in

Diameter 3.6209-3.6216 in
Gaged on the skirt 13 mm (0.51 inch) below the centerline
of the piston pin bore
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 39
Chevrolet Venture V6-3.4L VIN E 488

Clearance 0.0013-0.0027 in

Pin Bore 0.9057-0.9060 in

Top Groove Side Clearance 0.002-0.0033 in

Second Groove Side Clearance 0.002-0.0035 in

Top Ring Gap 0.006-0.014 in

Second Ring Gap 0.0197-0.0280 in

Oil Ring Groove Clearance 0.008 in

Gap with segment at 92.0 mm (3.62 inch) 0.0098-0.05 in

Rod Bearing Journal Clearance 0.0007-0.0024 in

Rod Side Clearance 0.007-0.017 in

Rod Bearing Bore Diameter 2.124-2.125 in

Connecting Rod Bearing Cap Nut 15 ft.lb


+ 75 degrees

Rod Bearing Journal Clearance 0.0007-0.0024 in

Rod Side Clearance 0.007-0.017 in

Rod Bearing Bore Diameter 2.124-2.125 in

Coolant Drain Plug 14 ft.lb

Crankshaft Balancer Bolt 76 ft.lb

Main Bearing Cap Bolts First Pass 37 lb. ft.

Final Pass +77 Degrees

Cylinder Block Main Bearing Bore Diameter 2.8407-2.8412 in

Crankshaft Main Bearing Inside Diameter 2.6492-2.6502 in

Main Bearing Clearance 0.0008-0.0025 in

Main Thrust Bearing Clearance 0.0012-0.0030 in


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 40
Chevrolet Venture V6-3.4L VIN E 489
Crankshaft End Play 0.0024-0.0083 in

Crankshaft-Main Bearing Cap Bolt/Stud 37 ft.lb


+ 77 degrees

Crankshaft Oil Deflector Nut 18 ft.lb

Main Journal Diameter 2.6473-2.6483 in

Main Journal Taper 0.0002 in

Out Of Round - Max 0.0002 in

Flange Runout - Max 0.0016 in

Cylinder Block Main Bearing Bore Diameter 2.8407-2.8412 in

Crankshaft Main Bearing Inside Diameter 2.6492-2.6502 in

Main Bearing Clearance 0.0008-0.0025 in

Main Thrust Bearing Clearance 0.0012-0.0030 in

Crankshaft End Play 0.0024-0.0083 in

Crankshaft Flange Runout - Max 0.0016 in

Rod Bearing Journal Diameter 1.9987-1.9994 in

Rod Bearing Journal Taper - Max 0.0002 in

Rod Bearing Journal Out Of Round - Max 0.0002 in

Rod Inside Bearing Diameter 2.000-2.002 in

Coolant Heater Bolt/Screw 18 in.lb

Crankshaft Balancer Bolt 76 ft.lb

Diameter 0.9052-0.9054 in

Clearance In Piston 0.0004-0.0008 in

Fit In Rod 0.0006-0.0018 in

Top Groove Side Clearance 0.002-0.0033 in

Second Groove Side Clearance 0.002-0.0035 in

Top Ring Gap 0.006-0.014 in

Second Ring Gap 0.0197-0.0280 in

Oil Ring Groove Clearance 0.008 in


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 41
Chevrolet Venture V6-3.4L VIN E 490

Gap with segment at 92.0 mm (3.62 inch) 0.0098-0.05 in

Diameter 3.6209-3.6216 in
Gaged on the skirt 13 mm (0.51 inch) below the centerline
of the piston pin bore

Clearance 0.0013-0.0027 in

Pin Bore 0.9057-0.9060 in

Camshaft Sprocket Bolt 103 lb. ft.

Cylinder Head Torque & Sequence


This article has been updated with TSB 02-06-01-003B, 4/15/08
This bulletin is being revised to include a Notice advising that the cylinder head bolts are NOT TO BE RE-USED. Please discard Corporate Bull

Notice: This component uses torque-to-yield bolts. When servicing this component, do not re-use the bolts. New torque-to-yield bolts must be ins

Tighten the NEW cylinder head bolts to 60 Nm (44 lb ft) in the order shown. Use the J 36660-A torque angle meter in order to rotate the cylinder

Exhaust Manifold Nut 12 ft.lb

Exhaust Manifold Stud 13 ft.lb

Exhaust Manifold Pipe Nut 26 ft.lb

Intake Manifold Coolant Pipe Bolt 89 in.lb

Lower Intake Manifold Bolt 115 in.lb

Upper Intake Manifold Bolt/Stud 18 ft.lb


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 42
Chevrolet Venture V6-3.4L VIN E 491

Rocker Arm Assembly


VALVE ROCKER ARM BOLT:
First Pass ........................................................................................................................................................................................ 19 Nm (14 ft. lbs.)
Final Pass ................................................................................................................................................................................................. (30 degrees)

Valve Clearance
The manufacturer indicates that this vehicle has hydraulic lifters or adjusters and therefore does not require adjustment.

Valve Rocker Arm Cover Bolt 89 in.lb

Seat Angle 45 deg

Valve Seat Runout 0.002 in

Seat Width-intake 0.061-0.071 in

Seat Width-Exhaust 0.067-0.079 in

Valve Springs Free Length 1.89 in

Valve Springs Load (Closed) 75 lbf at 1.701 in

Valve Springs Load (Open) 230 lbf at 1.260 in

Installed Height Intake-Exhaust 1.701 in

Approx. # or coils 6.55

Valve Margin - Minimum Intake 0.083 in

Valve Margin - Minimum Exhaust 0.106 in

Valve Stem Clearance 0.0010-0.0027 in

Valve Face Angle 45 deg

Drive Belt Shield Bolt 89 in.lb


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 43
Chevrolet Venture V6-3.4L VIN E 492

Drive Belt Tensioner Bolt 37 ft.lb

Generator Bracket and Front Engine Lift Hook Bolt 37 ft.lb

Engine Mount Bracket Bolt 43 ft.lb

Engine Mount Lower Nut 32 ft.lb

Engine Mount Strut and Lift Bracket Bolt - Engine Left Rear 52 ft.lb

Engine Mount Strut Bolt/Nut 35 ft.lb

Engine Mount Strut Bracket Bolt - Upper Radiator Support 21 ft.lb

Engine Mount Strut Bracket Bolt - Vehicle Right Side 37 ft.lb

Engine Mount Upper Nut 35 ft.lb

Oil Level Indicator Tube Stud 18 ft.lb

Oil Pan Drain Plug 18 ft.lb

Intake Manifold Torque & Sequence

Lower Intake Manifold

Install NEW lower intake manifold bolts.

The torque specification is a 2-step process; tighten the vertical lower intake manifold bolts (the four middle ones) to 7 Nm (62 lb in). Tighten the di

UPPER INTAKE MANIFOLD BOLT/STUD ................................................................................................................................... 25 Nm (18 lb. ft.)

Throttle Body Bolt/Stud 18 lb. ft.


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 44
Chevrolet Venture V6-3.4L VIN E 493

Valve Lifter Guide Bolt 89 in.lb

Roller Lifter Hydraulic

Oil Cooler Connector 37 ft.lb

Oil Filter Bypass Hole Plug 14 ft.lb

Oil Filter Fitting 29 ft.lb

Oil Filter 115 in.lb

Oil Level Sensor Bolt 89 in.lb

Engine Oil Level Switch 22 Nm

Oil Cooler Hose Fitting 14 ft.lb

Oil Cooler Pipe Bracket Bolt 89 in.lb

Oil Pan Bolt 18 ft.lb

Oil Pan Side Bolt 37 ft.lb

Engine Oil Pressure Indicator Switch 115 in.lb

Engine Oil Pressure Indicator 16 Nm

Oil Pump Cover Bolt 89 in.lb

Oil Pump Oil Pump Drive Clamp Bolt 27 ft.lb

Oil Pump Mounting Bolt 30 ft.lb


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 46
45
Chevrolet Venture V6-3.4L VIN E 494
Instrument Panel Cluster Screws 2.5 Nm
Gear
Flywheel Length
Bolts 52 lb. ft. 1.199-1.200 inch
Instrument Panel Compartment Latch Screws 1 Nm
Diameter 1.498-1.500 inch
Instrument Panel Compartment Screws 2.5 Nm
Side Clearance 0.001-0.003 in
Instrument
Battery PanelCable
Positive LowertoBrace Bolts/Screws
Underhood 2 Nm Nut 10 Nm
Electrical Center
End Clearance 0.002-0.005 in

Valve to Bore Clearance 0.0015-0.0035 in

Knee Bolster
Heater Bolts/Screws
Core Line
Gear LashScrew2.5 Nm1.6 Nm0.0037-0.0077 inch
Clip

Heater Core Mounting Clip


Gear Pocket Screw 1.6 Nm1.202-1.204 in
Depth

Gear Pocket Diameter 1.503-1.505 in


Forward Indicator Lamp Screws 1.9 Nm

Side Marker
Heater Lamp
Inlet Pipe Screws Nut 71.5
Mounting NmNm

Camshaft Sprocket Bolt 103 lb. ft.

Fog Lamps Screws


Compressor Pressure 9.5 NmValve 9 Nm
Relief

Crankshaft Balancer Bolt 76 ft.lb

Headlamp
A/C Capsule
Compressor Screws
Hose 7 Nm
Block Fitting to Compressor Nut 22 Nm

Sealed
A/C Beams Headlamp
Compressor
Timing Screws
Hose Block
Chain Dampener 157ft.lb
BoltFitting Nm
to Accumulator Bolt 16 Nm

Liquid Line at Block Fitting Bolt 16 Nm

Liquid Line at Condensor Fitting 27 Nm


Front Parking
Engine Lamp Bolt
Front Cover Lens- Screws
Large 941Nmft.lb
Liquid Line at Orifice Fitting 27 Nm
Engine Front Cover Bolt - Medium 35 ft.lb
Liquid Line at Rear Fitting (C34 only) 27 Nm
HVAC
EngineSystem
FrontAir Conditioner
Cover Bolt -Heater
SmallCombination (FRT/RR w/Rear
15 ft.lb
Controls)
Data Link Connector Bolts/Screws 2 Nm

Suction Line at Accumulator Fitting 47 Nm

Suction Line at Block Fitting Bolt 16 Nm


Catalytic Converter Nut 25 ft.lb
A/C Compressor Hose Block Fitting to Rear Suction Line Bolt 16 Nm

Housing Assembly HVAC


Data
Heater Link
Exhaust
A/C Connector
Crossover
Module Bolts/Screws
Pipe
Bolts Nut/Stud
to 182 ft.lb
Nm Compartment.....20
Inside Passenger Nm 15 ft lb

Heater A/C Module Nuts to Engine Compartment................10 Nm 89 in lb

Heater A/C Module Upper Mounting Screws.....................1.6 Nm 14 in lb


CamshaftManifold
Exhaust Position Nut
Sensor Bolt1289 in.lb
ft.lb
Rear Heater A/C Module Mounting Bolts and Nuts..............10 Nm 89 in lb
Exhaust Manifold Stud 13 ft.lb

Exhaust
InflatableManifold
RestraintPipe
SideNut 26Sensor
Impact ft.lb (SIS) Fasteners 10 Nm
Coolant Temperature Sensor 17 ft.lb

Exhaust Manifold
Instrument Heat Shield
Panel Accessory BoltPlate Screws
Trim 89 in.lb
2 Nm
Crankshaft Position Sensor Bolt - Front Cover 89 in.lb
Exhaust Crossover
Instrument Pipe Heat Shield Bolt 89 in.lb
Panel Bolts/Screws 10 Nm
Crankshaft Position Sensor Stud - Side of Engine Block 98 in.lb
Chevrolet Venture V6-3.4L VIN E 495
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 47
Chevrolet Venture V6-3.4L VIN E 496
Crankshaft Position Sensor Wiring Bracket Bolt 37 ft.lb

Idle Air Control Valve Attaching Screws 3 Nm

Knock Sensor 19 Nm

Manifold Absolute Pressure (MAP) Sensor Retaining Bolt 3 Nm

Heated Oxygen Sensor 41 Nm

Throttle Position Sensor Screws 2 Nm

EVAP Purge Valve Bracket 10 Nm

Exhaust Gas Recirculation Valve to Throttle Body Adapter Bolts 30 Nm

Fuel Tank Filler Pipe Hose Clamp 2.5 Nm

Firing Order
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 48
Chevrolet Venture V6-3.4L VIN E 497

Firing Order 1-2-3-4-5-6

For number 1 cylinder location, See: Engine, Cooling and Exhaust/Engine/Tune-up and Engine Performance Checks/Ignition Timing/Number One C

See: Engine, Cooling and Exhaust/Engine/Tune-up and Engine Performance Checks/Ignition Cable

In-Pipe Fuel Filter Outlet Nut 30 Nm

Fuel Rail Attaching Nuts or Bolts 10 Nm

Fuel Tank Retaining Strap Bolts 48 Nm

Idle Speed
Information not supplied by the manufacturer.
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 49
Chevrolet Venture V6-3.4L VIN E 498

Spark Plug Wires 1,968 Ohms/Meter

Ignition Coil to Ignition Control Module Screws 4.5 Nm

Ignition Coil to Ignition Control Module Screws 4.5 Nm

Ignition Control Module Bracket to Engine Studs and Nuts 25 Nm

Upper Intake Manifold Studs or Bolts 25 Nm

Spark Plug Gap


Spark Plug Gap .............................................................................................................................................................................. 1.524mm (0.060 in)
Spark Plug Torque
Initital Installation ................................................................................................................................................................................. 20 Nm (15 lb ft)
Reinstallation ........................................................................................................................................................................................ 15 Nm (11 lb ft)

Exhaust Gas Recirculation Valve to Throttle Body Adapter Bolts 30 Nm

Throttle Body Retaining Nuts or Bolts 28 Nm

Throttle Cable/Linkage
Accelerator Cable Bracket Retaining Nuts and Bolts 10 N.m

A/C Refrigerant Pressure Sensor 5 Nm

Front Seat/Retractor Side Seat Belt Lower Anchor Nuts 40 Nm

Front Shoulder Belt Guide Adjuster Bracket Bolts 50 Nm

Front Seat Belt Upper Guide Loop Anchor Nut 29 Nm

Lower Seat Belt Anchor Bolt (C-Pillar) 43 Nm

Lower Seat Belt Anchor Bolt (D-Pillar) 43 Nm

Upper Seat Belt Anchor Bolt (C-Pillar) 43 Nm

Upper Seat Belt Anchor Bolt (D-Pillar) 43 Nm

Rear Seat Center Belt Bolts 53 Nm

Front Seat Buckle Side Belt Nut 53 Nm

Rear Seat Buckle Belt Bolts (All) 53 Nm


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 50
Chevrolet Venture V6-3.4L VIN E 499
Rear Seat Buckle Belt Nut (All) 53 Nm

Mini-Buckle Bolt 53 Nm

Front Seat Belt Retractor Bolt 43 Nm

Seat Belt Retractor Bolt (C-Pillar) 43 Nm

Seat Belt Retractor Bolt (D-Pillar) 43 Nm

Driver Seat Belt Pretensioner Fastener 35 Nm

Passenger Seat Belt Pretensioner Fastener 35 Nm

Service Port HVAC


A/C Refrigerant Service Valve ............................................................................................................................................................................. 11 N.m

Starter Motor Bolt 47 Nm

Starter Motor BAT Terminal Nut 10 Nm

Starter Motor S Terminal Nut 3 Nm

Model PG260 F1

Cooler Pipe Retainer Bolt/Screw 89 in.lb

Power Steering Cooler Hose/Pipe Fittings 20 ft.lb

Power Steering Pump Bolts 25 ft.lb


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 51
Chevrolet Venture V6-3.4L VIN E 500

Steering Column Cover Bolts 38 in.lb

Steering Column Bolts 18 ft.lb

Steering Column Nuts 18 ft.lb

Power Steering Gear Nuts (at Frame) 59 ft.lb

Steering Intermediate Shaft Lower (Pinch) Bolt 33 ft.lb

Steering Wheel Nut 33 ft.lb


Steering Wheel Nut

Tie Rod Ball Stud Nut 22 ft.lb


+ 120 degrees (2 flats)

Wheel Bearing/Hub Bolts (NEW ONLY) 96 ft.lb

Wheel Bearing/Hub Bolts (NEW ONLY) 63 ft.lb


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 52
Chevrolet Venture V6-3.4L VIN E 501

Air Dryer, Suspension Control


Air Dryer Bracket Bolts/Screws ....................................................................................................................................................... 7 Nm (62 inch lbs.)
Air Line, Suspension Control
Air Line Tube Repair Nut ................................................................................................................................................................. 8 Nm (70 inch lbs.)

Front Wheel Drive Axle Nut 118 ft.lb

Rear Axle Tie Rod Bolt 92 ft.lb

Ball Stud Nuts (Replacement Ball Joint) 50 ft.lb


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 53
Chevrolet Venture V6-3.4L VIN E 502

Wear Limit
Important: This is a prevailing torque type fastener. This fastener may be reused ONLY if:
- The fastener and its counterpart are clean and free from rust
- The fastener develops 2 Nm (18 inch lbs.) of torque (drag) against its counterpart prior to the fastener seating. If the fastener does not mee

Compressor/Pump Relay, Suspension Control


Air Compressor Relay Bolt/Screw ................................................................................................................................................... 3 Nm (27 inch lbs.)

Air Compressor Bolts/Screws 35 in.lb

Air Compressor Bracket Bolt/Screw 37 ft.lb

Air Compressor Bracket Nuts 89 in.lb

Air Compressor Head Bolts 53 in.lb

Air Compressor Shield Bolt/Screw 27 in.lb

Ball Stud Castle Nut (Lower Control Arm) 40 ft.lb

Lower Control Arm Nuts (at Frame) 83 ft.lb

Control Arm Nut 162 ft.lb

Inflator Relay Bolts/Screws 18 in.lb

Inflator Solenoid Fill Valve Nut 27 in.lb

Inflator Solenoid Nut 27 in.lb

Height Sensor Adjuster Bolt/Screw 44 in.lb

Height Sensor Ball Stud 35 in.lb

Height Sensor Bolts/Screws 35 in.lb

Height Sensor Bracket Bolts/Screws 89 in.lb

Shock Absorber Nut 63 ft.lb

Stabilizer Shaft Insulator Bracket Bolts 35 in.lb

Stabilizer Shaft Link Nut 17 ft.lb


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 54
Chevrolet Venture V6-3.4L VIN E 503

Strut Lower Nuts (at Knuckle) 90 ft.lb

Strut Shaft Nut 63 ft.lb

Strut Upper Nuts 30 ft.lb

Vacuum Tank Mounting Nuts 10 Nm

Wheel Nuts 100 ft.lb

Wheel Nut Caps (Pontiac and Export Vehicles with Aluminum Wheels) 27 in.lb

Lug Nut Torque Patterns

Windows
Fastener Tightening Specifications

Solvent Container Assembly Mounting Screws 6 Nm

Wiper Arm Assembly to Shaft Nut 48 Nm

Wiper Module Assembly to Vehicle Screws 10 Nm


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 55
Chevrolet Venture V6-3.4L VIN E 504

Wiper Motor Assembly Mounting Screws 7 Nm

Wiper Motor Crank Arm Assembly Screw 14-17 Nm

Wiper Linkage Assembly to Wiper Motor Crank Arm Assembly Screws 5 Nm

Wiper Motorover Assembly Screws 2 Nm

Wiper Linkage Assembly to Wiper Motor Crank Arm Assembly Screws 5 Nm

Compression Check
The lowest reading should not be less than 70 percent of the highest reading.

No cylinder reading should be less than 689 kPa (100 psi).

Engine Oil
For information regarding oil pressure specifications, refer to Lubrication System specifications. See: Engine, Cooling and Exhaust/Engine/Engine L

Oil Pressure - Warm 15 psi at 1100 rpm

Fuel Injector Pressure Drop


Fuel Injector Pressure Drop
If the pressure drop value for each injector is within 1.5 psi of the average drop value the fuel injectors are flowing properly.

Pressure Drop 1.5 psi

Fuel Injector Balance Test Example (Typical)

Fuel System Pressure


Fuel System Pressure
2000 Chevy Truck Venture
Chevrolet Venture
V6-3.4L VIN E V6-3.4L VIN E 505
Copyright © 2011,
ALLDATA 10.40
Page 56

Key On Engine Off 52-59 psi

Fuel System Pressure


Fuel System Pressure

Key On Engine Off 52-59 psi

Oil Pump, Engine


For information regarding oil pressure specifications, refer to Lubrication System specifications. See: Engine, Cooling and Exhaust/Engine/Engine L

Thermostat Temperature Range Starts To Open 87 Degrees C


188 Degrees F

Fully Open 97 Degrees C


206 Degrees F

System Specifications
Bottom Pan Removal ................................................................................................................................................................................ 7.0L (7.4 qts.)
Complete Overhaul .................................................................................................................................................................................. 9.5L (10.0 qts)
Dry ........................................................................................................................................................................................................ 12.7L (13.4 qts.)
Fluid - A/T
Transmission Fluid
Pan Removal .............................................................................................................................................................................................. 7.0L (7.4 Qt)
Overhaul ................................................................................................................................................................................................... 9.5L (10.0 Qt)
Dry ......................................................................................................................................................................................................... 12.7L (13.4 Qt)

With Rear Climate Control 11.9 qt (US)


Note: Recheck fluid level after filling system.

W/O Rear Climate Control 9.6 qt (US)


Note: Recheck fluid level after filling system.

Engine Oil
Engine Oil

With Filter Change ..................................................................................................................................................................................... 4.2L (4.5 Qt)

NOTE: ALL capacity specifications are approximate. When replacing or adding fluids, fill to the recommended level and recheck fluid level.

Standard/Regular 19.8 gal (US)

Optional/Extended 25 gal (US)

System Specifications
Front A/C ................................................................................................................................................................................................ 0.90 kg / 2.0 lb

Front and Rear A/C................................................................................................................................................................................. 1.31 kg / 2.9 lb


Refrigerant
Refrigerant Capacity
C34 .................................................................................................................................................................................................................. 1.31 kg
C60 .................................................................................................................................................................................................................. 1.08 kg
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 57
Chevrolet Venture V6-3.4L VIN E 506
Refrigerant Oil
The manufacture does not provide refrigerant oil capacities for this vehicle.
Maintenance
FLUID CAPACITY/LEVELS
Note that ALL capacity specifications are approximate. When replacing or adding fluids, fill to the recommended level and recheck fluid level.

Type Dexron(R)-III Automatic Transmission Fluid or Equivalent

Fluid - A/T
Transmission Fluid Type

Type .................................................................................................................................................................................... DEXRON III or Equivalent

Brake Fluid Type Delco Supreme II (R) Fluid, GM P/N 12377967 Or DOT-3 Equivalent

Type Goodwrench(R) or Havoline(R) Silicate-Free DEX-COOL(R)

Coolant/Water Mixture 50/50 %

Engine Oil
Engine Oil

API Classification .................................................................................................................................................................. Look for Starburst Symbol


Grade ............................................................................................................................................................. 5W-30 (preferred), 10W-30 if above 0° F
A Recommended Fluids and Lubricants
Look for and use ONLY the oils, fluids and fuel that meet GM Specification. Oil or fluid that does not have the correct specification designation can
Automatic/Manual Transmission/Transaxle Shift Linkage
Lubricate shift linkage with engine oil.
C/V, Universal Joints, Yoke Splines and Clutch Fork
Chassis lubricant, GM P/N 12377985 or lubricant meeting the requirements of NLGI grade 2, category LB or GC-LB.
Chassis Lubrication
Chassis lubricant, GM P/N 12377985 or lubricant meeting the requirements of NLGI # 2, category LB or GC-LB.
Hinges and Locks
Multi-Purpose lubricant Superlube(R), GM P/N 12346241 or equivalent.
Key Lock Cylinders
Multi-Purpose lubricant Superlube(R), GM P/N 12346241 or equivalent.
Misc.. Linkage, Latches, Pivots and Spring Anchors
Lubriplate lubricant aerosol, GM P/N 12346293 or lubricant meeting the requirements of NLGI # 2, category LB or GC-LB.
Parking Brake Cable Guides
Chassis lubricant, GM P/N 12377985 or lubricant meeting the requirements of NLGI # 2, category LB or GC-LB.
Weatherstrip Conditioning
Dielectric Silicone Grease, GM P/N 12345579 or equivalent.
Wheel Bearings
Wheel bearing lubricant, GM P/N 1051344 or lubricant meeting requirements of NLGI grade 2, category GC or GC-LB.
Windshield Washer Solvent
GM Optikeen(R) washer solvent, GM P/N 1051515 or equivalent.
x
x
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 58
Chevrolet Venture V6-3.4L VIN E 507
Power Steering Fluid GM Power Steering Fluid (GM P/N 1050017 - 1 quart or Equivalent)

Cold Climate Power Steering Fluid 12345866 or Equivalent

Refrigerant
Refrigerant Type ................................................................................................................................................................................................ R-134a
Refrigerant Oil
A/C System O-ring and
Fitting Lubricant .................................................................................................................................................................. 525 Viscosity Mineral Oil

Internal Lubricant
(Including Compressor) ............................................................................................................ Poly-Alkaline Glycol (PAG) Synthetic Refrigerant Oil

Wheel Bearing
On models with serviceable wheel bearings, use GC Wheel Bearing Grease.

GC ............................................................................................................................................................. Wheel Bearing Grease, NLGI Classification


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 1
Chevrolet Venture V6-3.4L VIN E 508
Vehicle: Locations

Ashtray Illumination Lamp

Locations View
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 2
Chevrolet Venture V6-3.4L VIN E 509

Locations View

Center of IP, mounted to the back of the ashtray


Cargo Lamp
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 3
Chevrolet Venture V6-3.4L VIN E 510

Locations View

Above the liftgate, on the roof headliner


Center High Mounted Stop Lamp (CHMSL)
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 4
Chevrolet Venture V6-3.4L VIN E 511

Locations View
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 5
Chevrolet Venture V6-3.4L VIN E 512

Locations View

Center, top of liftgate


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 6
Chevrolet Venture V6-3.4L VIN E 513

Locations View

Dome Lamp
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 7
Chevrolet Venture V6-3.4L VIN E 514

Locations View

Center of the roof headliner


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 8
Chevrolet Venture V6-3.4L VIN E 515

Locations View
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 9
Chevrolet Venture V6-3.4L VIN E 516

Locations View
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 10
Chevrolet Venture V6-3.4L VIN E 517

Locations View

Forward Lamp Harness


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 11
Chevrolet Venture V6-3.4L VIN E 518

Locations View
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 12
Chevrolet Venture V6-3.4L VIN E 519

Locations View
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 13
Chevrolet Venture V6-3.4L VIN E 520

Locations View
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 14
Chevrolet Venture V6-3.4L VIN E 521

Locations View
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 15
Chevrolet Venture V6-3.4L VIN E 522

Locations View

Front Roof Rail Reading Lamps


On both sides of the headliner between the B and C-pillars
Hazard Lamp Flasher (Export)
Below the IP, above the base of the steering column, left side of the steering column
Hazard Lamp/Turn Signal Flasher
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 16
Chevrolet Venture V6-3.4L VIN E 523

Locations View

Below the IP, above the base of the steering column, left side of the steering column
Headlamp Position Lamp (Export)
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 17
Chevrolet Venture V6-3.4L VIN E 524

Locations View

Front of the vehicle


Instrument Panel (IP) Courtesy Lamp, Left
Below left side of the IP, near the park brake
IP Courtesy Lamp, Right
Below the right side of the IP
License Lamps
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 18
Chevrolet Venture V6-3.4L VIN E 525

Locations View
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 19
Chevrolet Venture V6-3.4L VIN E 526

Locations View

Rear of the vehicle, above the license plate


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 20
Chevrolet Venture V6-3.4L VIN E 527

Locations View
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 21
Chevrolet Venture V6-3.4L VIN E 528

Locations View
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 22
Chevrolet Venture V6-3.4L VIN E 529

Locations View

Rear Roof Rail Reading Lamps


On both sides of the roof headliner, behind the left C-pillar and the left D-pillars
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 23
Chevrolet Venture V6-3.4L VIN E 530

Locations View
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 24
Chevrolet Venture V6-3.4L VIN E 531

Locations View
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 25
Chevrolet Venture V6-3.4L VIN E 532

Locations View

Security Indicator Lamp


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 26
Chevrolet Venture V6-3.4L VIN E 533

Locations View

Center of the IP, mounted to the trim plate, near the windshield defrost vent
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 27
Chevrolet Venture V6-3.4L VIN E 534

Locations View
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 28
Chevrolet Venture V6-3.4L VIN E 535

Locations View
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 29
Chevrolet Venture V6-3.4L VIN E 536

Locations View

Windshield Header Courtesy/Reading Lamps


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 30
Chevrolet Venture V6-3.4L VIN E 537

Locations View

Part of the roof console


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 31
Chevrolet Venture V6-3.4L VIN E 538

Locations View
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 32
Chevrolet Venture V6-3.4L VIN E 539

Locations View
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 33
Chevrolet Venture V6-3.4L VIN E 540

Locations View

Locations View
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 34
Chevrolet Venture V6-3.4L VIN E 541

Locations View

Air Injection Bleed Valve


Left rear of engine, above valve cover
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 35
Chevrolet Venture V6-3.4L VIN E 542

Locations View
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 36
Chevrolet Venture V6-3.4L VIN E 543

Locations View
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 37
Chevrolet Venture V6-3.4L VIN E 544

Locations View

Locations View

Auto Level Control (ALC) Air Compressor


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 38
Chevrolet Venture V6-3.4L VIN E 545

Locations View

Under the vehicle, behind the left rear wheelhouse


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 39
Chevrolet Venture V6-3.4L VIN E 546

Locations View
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 40
Chevrolet Venture V6-3.4L VIN E 547

Locations View
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 41
Chevrolet Venture V6-3.4L VIN E 548

Locations View
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 42
Chevrolet Venture V6-3.4L VIN E 549

Locations View
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 43
Chevrolet Venture V6-3.4L VIN E 550

Locations View
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 44
Chevrolet Venture V6-3.4L VIN E 551
Locations View

Locations View
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 45
Chevrolet Venture V6-3.4L VIN E 552

Locations View
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 46
Chevrolet Venture V6-3.4L VIN E 553

Locations View
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 47
Chevrolet Venture V6-3.4L VIN E 554

Locations View

Battery
Engine compartment, behind the right headlamp
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 48
Chevrolet Venture V6-3.4L VIN E 555

Locations View

Body Harness
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 49
Chevrolet Venture V6-3.4L VIN E 556

Locations View
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 50
Chevrolet Venture V6-3.4L VIN E 557

Locations View
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 51
Chevrolet Venture V6-3.4L VIN E 558

Locations View
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 52
Chevrolet Venture V6-3.4L VIN E 559

Locations View
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 53
Chevrolet Venture V6-3.4L VIN E 560

Locations View
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 54
Chevrolet Venture V6-3.4L VIN E 561

Locations View
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 55
Chevrolet Venture V6-3.4L VIN E 562

Locations View
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 56
Chevrolet Venture V6-3.4L VIN E 563

Locations View
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 57
Chevrolet Venture V6-3.4L VIN E 564

Locations View
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 58
Chevrolet Venture V6-3.4L VIN E 565

Locations View
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 59
Chevrolet Venture V6-3.4L VIN E 566

Locations View
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 60
Chevrolet Venture V6-3.4L VIN E 567

Locations View

Brake Modulator
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 61
Chevrolet Venture V6-3.4L VIN E 568

Locations View

Left side of the engine compartment, mounted to the brake master cylinder
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 62
Chevrolet Venture V6-3.4L VIN E 569

Locations View
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 63
Chevrolet Venture V6-3.4L VIN E 570

Locations View

Cigar Lighter
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 64
Chevrolet Venture V6-3.4L VIN E 571

Locations View

Center IP, right side of the ashtray

Locations View
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 65
Chevrolet Venture V6-3.4L VIN E 572

Locations View
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 66
Chevrolet Venture V6-3.4L VIN E 573

Locations View

Cruise Control Release Switch


Mounted to the brake pedal support
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 67
Chevrolet Venture V6-3.4L VIN E 574

Locations View
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 68
Chevrolet Venture V6-3.4L VIN E 575

Locations View
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 69
Chevrolet Venture V6-3.4L VIN E 576

Locations View
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 70
Chevrolet Venture V6-3.4L VIN E 577

Locations View
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 71
Chevrolet Venture V6-3.4L VIN E 578

Locations View
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 72
Chevrolet Venture V6-3.4L VIN E 579

Locations View
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 73
Chevrolet Venture V6-3.4L VIN E 580

Locations View
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 74
Chevrolet Venture V6-3.4L VIN E 581

Locations View

Driver Information Display


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 75
Chevrolet Venture V6-3.4L VIN E 582

Locations View

In the roof console


Driver Seat Belt Pretensioner
---
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 76
Chevrolet Venture V6-3.4L VIN E 583

Locations View
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 77
Chevrolet Venture V6-3.4L VIN E 584

Locations View
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 78
Chevrolet Venture V6-3.4L VIN E 585

Locations View
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 79
Chevrolet Venture V6-3.4L VIN E 586

Locations View
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 80
Chevrolet Venture V6-3.4L VIN E 587

Locations View
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 81
Chevrolet Venture V6-3.4L VIN E 588

Locations View
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 82
Chevrolet Venture V6-3.4L VIN E 589

Locations View
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 83
Chevrolet Venture V6-3.4L VIN E 590

Locations View
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 84
Chevrolet Venture V6-3.4L VIN E 591

Locations View
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 85
Chevrolet Venture V6-3.4L VIN E 592

Locations View
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 86
Chevrolet Venture V6-3.4L VIN E 593

Locations View

Engine Harness
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 87
Chevrolet Venture V6-3.4L VIN E 594

Locations View
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 88
Chevrolet Venture V6-3.4L VIN E 595

Locations View
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 89
Chevrolet Venture V6-3.4L VIN E 596

Locations View
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 90
Chevrolet Venture V6-3.4L VIN E 597

Locations View
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 91
Chevrolet Venture V6-3.4L VIN E 598

Locations View
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 92
Chevrolet Venture V6-3.4L VIN E 599

Locations View
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 93
Chevrolet Venture V6-3.4L VIN E 600

Locations View
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 94
Chevrolet Venture V6-3.4L VIN E 601

Locations View

Locations View
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 95
Chevrolet Venture V6-3.4L VIN E 602

Locations View

Locations View
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 96
Chevrolet Venture V6-3.4L VIN E 603

Locations View

Locations View
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 97
Chevrolet Venture V6-3.4L VIN E 604

Locations View

Locations View
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 98
Chevrolet Venture V6-3.4L VIN E 605

Locations View

Exhaust Gas Recirculation (EGR) VaIve


Upper left side of the engine

Locations View
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 99
Chevrolet Venture V6-3.4L VIN E 606

Locations View

Front Door Lock


Inside, rear end of the front door
Front Door Lock (Actuator)
Part of the front door lock
Front Door Speakers
Inside the front door
Front Electric Accessory Plug Housing
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 100
Chevrolet Venture V6-3.4L VIN E 607

Locations View

Center of the IP, left of the ashtray


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 101
Chevrolet Venture V6-3.4L VIN E 608

Locations View
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 102
Chevrolet Venture V6-3.4L VIN E 609

Locations View
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 103
Chevrolet Venture V6-3.4L VIN E 610

Locations View

Locations View
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 104
Chevrolet Venture V6-3.4L VIN E 611

Locations View

Fuel Injectors
Top of the engine at each cylinder intake port
Fuel Level Sender
Mounted inside the fuel tank
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 105
Chevrolet Venture V6-3.4L VIN E 612

Locations View
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 106
Chevrolet Venture V6-3.4L VIN E 613

Locations View
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 107
Chevrolet Venture V6-3.4L VIN E 614

Locations View

Fuel Tank
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 108
Chevrolet Venture V6-3.4L VIN E 615

Locations View
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 109
Chevrolet Venture V6-3.4L VIN E 616

Locations View

Below the left side, middle of the vehicle


Fuse Block
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 110
Chevrolet Venture V6-3.4L VIN E 617

Locations View

Right side of the IP, in the right front door opening


Fusible Link A
Bolted to the starter solenoid
Fusible Link C
Bolted to the starter solenoid
Fusible Link Z
Bolted to the starter solenoid
Fusible Links
Bolted to the starter solenoid
Generator
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 111
Chevrolet Venture V6-3.4L VIN E 618

Locations View
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 112
Chevrolet Venture V6-3.4L VIN E 619

Locations View

Top rear right side of the engine


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 113
Chevrolet Venture V6-3.4L VIN E 620

Locations View
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 114
Chevrolet Venture V6-3.4L VIN E 621

Locations View
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 115
Chevrolet Venture V6-3.4L VIN E 622

Locations View

Headlamps
Front side of the vehicle
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 116
Chevrolet Venture V6-3.4L VIN E 623

Locations View
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 117
Chevrolet Venture V6-3.4L VIN E 624

Locations View
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 118
Chevrolet Venture V6-3.4L VIN E 625

Locations View
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 119
Chevrolet Venture V6-3.4L VIN E 626

Locations View

Horn, Left
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 120
Chevrolet Venture V6-3.4L VIN E 627

Locations View

Front left side of the vehicle, mounted to the left side of the front lower crossmember
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 121
Chevrolet Venture V6-3.4L VIN E 628

Locations View
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 122
Chevrolet Venture V6-3.4L VIN E 629

Locations View

Horn, Right
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 123
Chevrolet Venture V6-3.4L VIN E 630

Locations View
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 124
Chevrolet Venture V6-3.4L VIN E 631

Locations View

Front right side of the vehicle, mounted to the right side of the front lower crossmember

Locations View

I/P Harness
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 125
Chevrolet Venture V6-3.4L VIN E 632

Locations View
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 126
Chevrolet Venture V6-3.4L VIN E 633

Locations View
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 127
Chevrolet Venture V6-3.4L VIN E 634

Locations View
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 128
Chevrolet Venture V6-3.4L VIN E 635

Locations View
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 129
Chevrolet Venture V6-3.4L VIN E 636

Locations View
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 130
Chevrolet Venture V6-3.4L VIN E 637

Locations View
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 131
Chevrolet Venture V6-3.4L VIN E 638

Locations View
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 132
Chevrolet Venture V6-3.4L VIN E 639

Locations View
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 133
Chevrolet Venture V6-3.4L VIN E 640

Locations View
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 134
Chevrolet Venture V6-3.4L VIN E 641

Locations View
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 135
Chevrolet Venture V6-3.4L VIN E 642

Locations View
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 136
Chevrolet Venture V6-3.4L VIN E 643

Locations View
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 137
Chevrolet Venture V6-3.4L VIN E 644

Locations View
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 138
Chevrolet Venture V6-3.4L VIN E 645

Locations View
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 139
Chevrolet Venture V6-3.4L VIN E 646

Locations View
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 140
Chevrolet Venture V6-3.4L VIN E 647

Locations View
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 141
Chevrolet Venture V6-3.4L VIN E 648

Locations View
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 142
Chevrolet Venture V6-3.4L VIN E 649

Locations View
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 143
Chevrolet Venture V6-3.4L VIN E 650

Locations View

Idle Air Control (IAC) Valve


Top of the engine, front of the throttle assembly
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 144
Chevrolet Venture V6-3.4L VIN E 651

Locations View
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 145
Chevrolet Venture V6-3.4L VIN E 652

Locations View
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 146
Chevrolet Venture V6-3.4L VIN E 653

Locations View

Instrument Cluster
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 147
Chevrolet Venture V6-3.4L VIN E 654

Locations View

Left side of the IP


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 148
Chevrolet Venture V6-3.4L VIN E 655

Locations View
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 149
Chevrolet Venture V6-3.4L VIN E 656

Locations View
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 150
Chevrolet Venture V6-3.4L VIN E 657

Locations View
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 151
Chevrolet Venture V6-3.4L VIN E 658

Locations View
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 152
Chevrolet Venture V6-3.4L VIN E 659

Locations View
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 153
Chevrolet Venture V6-3.4L VIN E 660

Locations View

Liftgate Door Lock


Inside the liftgate, below the license plate
Liftgate Door Lock (Actuator)
Part of the liftgate door lock
Liftgate Harness
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 154
Chevrolet Venture V6-3.4L VIN E 661

Locations View
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 155
Chevrolet Venture V6-3.4L VIN E 662

Locations View
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 156
Chevrolet Venture V6-3.4L VIN E 663

Locations View
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 157
Chevrolet Venture V6-3.4L VIN E 664

Locations View
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 158
Chevrolet Venture V6-3.4L VIN E 665

Locations View
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 159
Chevrolet Venture V6-3.4L VIN E 666

Locations View
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 160
Chevrolet Venture V6-3.4L VIN E 667

Locations View

Mass Air Flow (MAF) Sensor


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 161
Chevrolet Venture V6-3.4L VIN E 668

Locations View

Left front of the engine compartment, in the air cleaner duct


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 162
Chevrolet Venture V6-3.4L VIN E 669

Locations View
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 163
Chevrolet Venture V6-3.4L VIN E 670

Locations View

Outside Rearview Mirror


On the outside of the front door
Outside Rearview Mirror (Heated Defogger)
In the outside rearview mirror
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 164
Chevrolet Venture V6-3.4L VIN E 671

Locations View
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 165
Chevrolet Venture V6-3.4L VIN E 672

Locations View
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 166
Chevrolet Venture V6-3.4L VIN E 673

Locations View
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 167
Chevrolet Venture V6-3.4L VIN E 674

Locations View
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 168
Chevrolet Venture V6-3.4L VIN E 675

Locations View
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 169
Chevrolet Venture V6-3.4L VIN E 676

Locations View
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 170
Chevrolet Venture V6-3.4L VIN E 677

Locations View

Passenger Seat Belt Pretensioner


--

Locations View
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 171
Chevrolet Venture V6-3.4L VIN E 678

Locations View
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 172
Chevrolet Venture V6-3.4L VIN E 679

Locations View

Power Sliding Door Unlatch Actuator


In the right power sliding door at the front of of the door
Power Sliding Door Unlatch Actuator (+E58) RH
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 173
Chevrolet Venture V6-3.4L VIN E 680

Locations View

For a Description of RPO Code(s) shown in this image refer to the RPO Code List found at Vehicle/Application and ID See: Application and
ID/RPO Codes
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 174
Chevrolet Venture V6-3.4L VIN E 681

Locations View
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 175
Chevrolet Venture V6-3.4L VIN E 682

Locations View

Radio
Center of the IP console
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 176
Chevrolet Venture V6-3.4L VIN E 683

Locations View
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 177
Chevrolet Venture V6-3.4L VIN E 684

Locations View

Radio Liftgate Speakers


On both sides of the liftgate
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 178
Chevrolet Venture V6-3.4L VIN E 685

Locations View
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 179
Chevrolet Venture V6-3.4L VIN E 686

Locations View

Radio Rear Seat Audio Control (WU3)


Part of the rear roof console, above the right passenger seat
Radio Rear Seat Audio Control (4 Door)
Part of the left rear armrest
Radio Rear Seat Audio Control (5 Door)
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 180
Chevrolet Venture V6-3.4L VIN E 687

Locations View

Part of the rear roof console, above the driver seat


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 181
Chevrolet Venture V6-3.4L VIN E 688

Locations View
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 182
Chevrolet Venture V6-3.4L VIN E 689

Locations View

Rear Door Lock (Actuator)


In the rear side door
Rear Electric Accessory Plug Housing
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 183
Chevrolet Venture V6-3.4L VIN E 690

Locations View

Inside the vehicle, behind the left rear wheelhouse


Rear Quarter Window Actuator
Rear part of the rear quarter window, on the D-pillar
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 184
Chevrolet Venture V6-3.4L VIN E 691

Locations View
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 185
Chevrolet Venture V6-3.4L VIN E 692

Locations View

Rear Sliding Door Alarm


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 186
Chevrolet Venture V6-3.4L VIN E 693

Locations View

Attached to the rear side door actuator motor


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 187
Chevrolet Venture V6-3.4L VIN E 694

Locations View

Rear Window Defogger Grid


Rear liftgate window
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 188
Chevrolet Venture V6-3.4L VIN E 695

Locations View
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 189
Chevrolet Venture V6-3.4L VIN E 696

Locations View

Remote Battery Stud


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 190
Chevrolet Venture V6-3.4L VIN E 697

Locations View

Engine compartment, connected to the underhood accessory wiring junction block, above the battery
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 191
Chevrolet Venture V6-3.4L VIN E 698

Locations View

Remote Control Door Lock Receiver (RCDLR)


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 192
Chevrolet Venture V6-3.4L VIN E 699

Locations View

Behind the center of the IP, underside of the IP trim, near the windshield defrost vent
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 193
Chevrolet Venture V6-3.4L VIN E 700

Locations View
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 194
Chevrolet Venture V6-3.4L VIN E 701

Locations View
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 195
Chevrolet Venture V6-3.4L VIN E 702

Locations View
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 196
Chevrolet Venture V6-3.4L VIN E 703

Second Seat Audio (SSA) Control


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 197
Chevrolet Venture V6-3.4L VIN E 704

Locations View
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 198
Chevrolet Venture V6-3.4L VIN E 705

Locations View

Overhead console, right side of video screen


Secondary Air Injection Pump
Mounted in lower portion of the drivers front fender
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 199
Chevrolet Venture V6-3.4L VIN E 706

Locations View
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 200
Chevrolet Venture V6-3.4L VIN E 707

Locations View
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 201
Chevrolet Venture V6-3.4L VIN E 708

Locations View
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 202
Chevrolet Venture V6-3.4L VIN E 709

Locations View
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 203
Chevrolet Venture V6-3.4L VIN E 710

Locations View
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 204
Chevrolet Venture V6-3.4L VIN E 711

Locations View
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 205
Chevrolet Venture V6-3.4L VIN E 712

Locations View
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 206
Chevrolet Venture V6-3.4L VIN E 713

Locations View
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 207
Chevrolet Venture V6-3.4L VIN E 714

Locations View
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 208
Chevrolet Venture V6-3.4L VIN E 715

Locations View
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 209
Chevrolet Venture V6-3.4L VIN E 716

Locations View
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 210
Chevrolet Venture V6-3.4L VIN E 717

Locations View
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 211
Chevrolet Venture V6-3.4L VIN E 718

Locations View
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 212
Chevrolet Venture V6-3.4L VIN E 719

Locations View
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 213
Chevrolet Venture V6-3.4L VIN E 720

Locations View
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 214
Chevrolet Venture V6-3.4L VIN E 721

Locations View
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 215
Chevrolet Venture V6-3.4L VIN E 722

Locations View

Sunshade Lighted Vanity Mirror, Right


Part of the right sunshade
Sunshade Lighted Vanity Mirrors
Part of both sunshades
Taillamp
Rear of the vehicle, on both sides
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 216
Chevrolet Venture V6-3.4L VIN E 723

Locations View

Taillamp, Right
Rear of the vehicle, right side
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 217
Chevrolet Venture V6-3.4L VIN E 724

Locations View

Third Seat Audio (TSA) Control


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 218
Chevrolet Venture V6-3.4L VIN E 725

Locations View

Right quarter trim panel, next to the [third row right seat]
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 219
Chevrolet Venture V6-3.4L VIN E 726

Locations View
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 220
Chevrolet Venture V6-3.4L VIN E 727

Locations View

Trailer Wiring Harness


Under the left right side of the vehicle, near the left rear wheelhouse
Underhood Accessory Wiring Junction Block
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 221
Chevrolet Venture V6-3.4L VIN E 728

Locations View
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 222
Chevrolet Venture V6-3.4L VIN E 729

Locations View

Engine compartment, front of the right wheelhouse, above the battery


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 223
Chevrolet Venture V6-3.4L VIN E 730

Locations View
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 224
Chevrolet Venture V6-3.4L VIN E 731

Locations View

Video Cassette Player (VCP)


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 225
Chevrolet Venture V6-3.4L VIN E 732

Locations View

Front floor console


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 226
Chevrolet Venture V6-3.4L VIN E 733

Locations View

Video Screen
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 227
Chevrolet Venture V6-3.4L VIN E 734

Locations View
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 228
Chevrolet Venture V6-3.4L VIN E 735

Locations View
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 229
Chevrolet Venture V6-3.4L VIN E 736

Locations View
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 230
Chevrolet Venture V6-3.4L VIN E 737

Locations View
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 231
Chevrolet Venture V6-3.4L VIN E 738

Locations View

Window Washer Pump, Rear


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 232
Chevrolet Venture V6-3.4L VIN E 739

Locations View

Engine compartment, mounted to the rear washer solvent container


Windshield Antenna
Within the windshield
Windshield Washer Pump
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 233
Chevrolet Venture V6-3.4L VIN E 740

Locations View

Engine compartment, mounted to the front washer solvent container


Auxiliary Video Module (AVM)
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 234
Chevrolet Venture V6-3.4L VIN E 741

Locations View
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 235
Chevrolet Venture V6-3.4L VIN E 742

Locations View
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 236
Chevrolet Venture V6-3.4L VIN E 743

Locations View

Overhead console, left side of video screen


Body Control Module (BCM)
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 237
Chevrolet Venture V6-3.4L VIN E 744

Locations View
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 238
Chevrolet Venture V6-3.4L VIN E 745

Locations View

Below the right side of the IP, right of the IP compartment


Cruise Control Module (CCM)
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 239
Chevrolet Venture V6-3.4L VIN E 746

Locations View
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 240
Chevrolet Venture V6-3.4L VIN E 747

Locations View

Locations View

Engine compartment, near the left strut tower


Daytime Running Lamps (DRL) Control Module
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 241
Chevrolet Venture V6-3.4L VIN E 748

Locations View

Right of the steering column, behind the IP


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 242
Chevrolet Venture V6-3.4L VIN E 749

Locations View

Electronic Brake Control Module (EBCM), without (NW9)


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 243
Chevrolet Venture V6-3.4L VIN E 750

Locations View

For a Description of RPO Code(s) shown in this image refer to the RPO Code List found at Vehicle/Application and ID See: Application and
ID/RPO Codes
Electronic Brake Traction Control Module (EBCM), with (NW9)
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 244
Chevrolet Venture V6-3.4L VIN E 751

Locations View

For a Description of RPO Code(s) shown in this image refer to the RPO Code List found at Vehicle/Application and ID See: Application and
ID/RPO Codes
Engine Coolant Level Indicator Module
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 245
Chevrolet Venture V6-3.4L VIN E 752

Locations View

Mounted to the rear right side of the radiator, below the radiator cap
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 246
Chevrolet Venture V6-3.4L VIN E 753

Locations View

Fog Lamp Module (Export), Rear


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 247
Chevrolet Venture V6-3.4L VIN E 754

Locations View

Below IP left side of steering column


Ignition Control Module (ICM)
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 248
Chevrolet Venture V6-3.4L VIN E 755

Locations View
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 249
Chevrolet Venture V6-3.4L VIN E 756

Locations View

Top center rear of the engine


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 250
Chevrolet Venture V6-3.4L VIN E 757

Locations View
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 251
Chevrolet Venture V6-3.4L VIN E 758

Locations View
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 252
Chevrolet Venture V6-3.4L VIN E 759

Locations View
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 253
Chevrolet Venture V6-3.4L VIN E 760

Locations View
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 254
Chevrolet Venture V6-3.4L VIN E 761

Locations View

Inflatable Restraint Steering Wheel Module


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 255
Chevrolet Venture V6-3.4L VIN E 762

Locations View
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 256
Chevrolet Venture V6-3.4L VIN E 763

Locations View
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 257
Chevrolet Venture V6-3.4L VIN E 764

Locations View

Interface Module (IM)


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 258
Chevrolet Venture V6-3.4L VIN E 765

Locations View
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 259
Chevrolet Venture V6-3.4L VIN E 766

Locations View

Inside overhead console, left corner


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 260
Chevrolet Venture V6-3.4L VIN E 767

Locations View
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 261
Chevrolet Venture V6-3.4L VIN E 768

Locations View
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 262
Chevrolet Venture V6-3.4L VIN E 769

Locations View

Pass Key III Module


In the steering column, at the ignition switch
Powertrain Control Module (PCM)
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 263
Chevrolet Venture V6-3.4L VIN E 770

Locations View

Locations View
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 264
Chevrolet Venture V6-3.4L VIN E 771

Engine compartment, secured in the air cleaner assembly


Rear Side Door Actuator Control Module

Locations View

Part of the rear side door actuator motor, right quarter panel, above the wheelhouse
Tape Retract Module (TRM)
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 265
Chevrolet Venture V6-3.4L VIN E 772

Locations View
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 266
Chevrolet Venture V6-3.4L VIN E 773

Locations View

Underneath left side instrument panel, near left side of the Data Link Connector (DLC), taped to the VCP harness
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 267
Chevrolet Venture V6-3.4L VIN E 774

Locations View
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 268
Chevrolet Venture V6-3.4L VIN E 775

Locations View
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 269
Chevrolet Venture V6-3.4L VIN E 776

Locations View

Engine Coolant Fan Motor 1 (RH)


Mounted to the rear left side of the radiator
Engine Coolant Fan Motor 2 (LH)
Mounted to the rear right side of the radiator
Front Window Regulator Motor
Inside the front door
Fuel Pump Motor
Mounted inside the fuel tank
Outside Rearview Mirror (Mirror Motor Pack)
In the outside rearview mirror
Passenger Seat Adjuster Motor Assembly
Under the right front seat
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 270
Chevrolet Venture V6-3.4L VIN E 777

Locations View

Rear Side Door Actuator Motor


Right quarter panel, above the wheelhouse
Rear Side Door Actuator Motor (Optical Sensor)
Part of the rear side door actuator motor
Rear Window Wiper Motor
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 271
Chevrolet Venture V6-3.4L VIN E 778

Locations View

Center of the liftgate


Seat Adjuster Motor Assembly
Under the front seat
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 272
Chevrolet Venture V6-3.4L VIN E 779

Locations View

Locations View

Locations View
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 273
Chevrolet Venture V6-3.4L VIN E 780

Starter Motor
Lower front of the engine

Locations View
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 274
Chevrolet Venture V6-3.4L VIN E 781

Locations View
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 275
Chevrolet Venture V6-3.4L VIN E 782

Locations View
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 276
Chevrolet Venture V6-3.4L VIN E 783

Locations View

Windshield Wiper Motor


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 277
Chevrolet Venture V6-3.4L VIN E 784

Locations View

Top right rear of the engine compartment


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 278
Chevrolet Venture V6-3.4L VIN E 785

Locations View

AIR Pump Relay


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 279
Chevrolet Venture V6-3.4L VIN E 786

Locations View

Forward lamp harness, right side of the engine compartment, rearward of the Horn
Auto Level Control (ALC) Air Inflator Relay
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 280
Chevrolet Venture V6-3.4L VIN E 787

Locations View

In the vehicle, behind the left rear wheelhouse


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 281
Chevrolet Venture V6-3.4L VIN E 788

Locations View

Backup Lamp Relay


Right side of steering column, behind IP
Cool Fan Relay
Engine compartment, in the underhood accessory wiring junction block
Cool Fan 1 Relay
Engine compartment, in the underhood accessory wiring junction block
Cool Fan 2 Relay
Engine compartment, in the underhood accessory wiring junction block
Crank Relay
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 282
Chevrolet Venture V6-3.4L VIN E 789

Locations View

Right side of Engine Compartment on the radiator support, inboard of the underhood accessory wiring junction block
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 283
Chevrolet Venture V6-3.4L VIN E 790

Locations View

Electronic Brake Control Relay


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 284
Chevrolet Venture V6-3.4L VIN E 791

Locations View
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 285
Chevrolet Venture V6-3.4L VIN E 792

Locations View

Above the park brake cable bracket, mounted to the electronic brake control module/electronic brake traction control module
Fuel Pump Relay (FPR)
Engine compartment, in the underhood accessory wiring junction block
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 286
Chevrolet Venture V6-3.4L VIN E 793

Locations View

Rear Fog Lamp Relay


Part of the relay center, right side of the IP, mounted to the bracket along with the BCM, near the rear top right side of the IP compartment
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 287
Chevrolet Venture V6-3.4L VIN E 794

Locations View
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 288
Chevrolet Venture V6-3.4L VIN E 795

Locations View

Relay Center
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 289
Chevrolet Venture V6-3.4L VIN E 796

Locations View
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 290
Chevrolet Venture V6-3.4L VIN E 797

Locations View

Right side of IP, mounted to the bracket along with the BCM, near the rear top right side of the IP compartment
Retained Accessory Power (RAP) Relay
In the relay center
Theft Deterrent Relay
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 291
Chevrolet Venture V6-3.4L VIN E 798

Locations View

Part of the relay center, right side of the IP, mounted to the bracket along with the BCM, near the rear top right side of the IP compartment
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 292
Chevrolet Venture V6-3.4L VIN E 799

Locations View
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 293
Chevrolet Venture V6-3.4L VIN E 800

Locations View

Auto Level Control (ALC) Sensor


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 294
Chevrolet Venture V6-3.4L VIN E 801

Locations View

Mounted to the rear crossmember above the rear axle


Automatic Transaxle Fluid Temperature (TFT) Sensor
Inside the automatic transaxle
Bank 1 Knock Sensor (KS)
Front of the engine, above the starter
Brake Fluid Level Indicator Sensor
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 295
Chevrolet Venture V6-3.4L VIN E 802

Locations View

Right side of the brake fluid reservoir


Camshaft Position (CMP) Sensor
Camshaft Position (CMP) Sensor
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 296
Chevrolet Venture V6-3.4L VIN E 803

(1) Camshaft Position Harness Connector

Note: The Camshaft Position (CMP) Sensor is located in the engine compartment, right side of the engine, above the A/C compressor clutch.
Crankshaft Position (CKP) Sensor (7X)
Lower rear of the engine
Crankshaft Position (CKP) Sensor (24X)
Right side of the engine, at the end of the crankshaft, behind the harmonic balancer
Daytime Running Lamp (DRL) Ambient Light Sensor
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 297
Chevrolet Venture V6-3.4L VIN E 804

Locations View

Center of IP, secured to the upper trim pad, near the windshield defrost vent
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 298
Chevrolet Venture V6-3.4L VIN E 805

Locations View

Engine Coolant Temperature (ECT) Sensor


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 299
Chevrolet Venture V6-3.4L VIN E 806

Locations View

Left side top of the engine

Locations View
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 300
Chevrolet Venture V6-3.4L VIN E 807

Locations View
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 301
Chevrolet Venture V6-3.4L VIN E 808

Locations View

Heated Oxygen Sensor 1 (HO2S 1)


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 302
Chevrolet Venture V6-3.4L VIN E 809

Locations View

Rear of the engine, in the exhaust manifold


Heated Oxygen Sensor 2 (HO2S 2)
In the exhaust system, behind the catalytic converter
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 303
Chevrolet Venture V6-3.4L VIN E 810

Locations View

Intake Air Temperature (IAT) Sensor


Left of engine compartment, on the air intake duct, near the throttle body
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 304
Chevrolet Venture V6-3.4L VIN E 811

Locations View
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 305
Chevrolet Venture V6-3.4L VIN E 812

Locations View

Manifold Absolute Pressure (MAP) Sensor


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 306
Chevrolet Venture V6-3.4L VIN E 813

Locations View

Right top of the engine


Mass Air Flow (MAF) Sensor
Left front of the engine compartment, in the air cleaner duct
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 307
Chevrolet Venture V6-3.4L VIN E 814

Locations View

Theft Deterrent Shock Sensor


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 308
Chevrolet Venture V6-3.4L VIN E 815

Locations View

Below the left side IP, right of the steering column


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 309
Chevrolet Venture V6-3.4L VIN E 816

Locations View

Throttle Position (TP) Sensor


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 310
Chevrolet Venture V6-3.4L VIN E 817

Locations View

Top of the engine, on the throttle assembly


Vehicle Speed Sensor (VSS)
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 311
Chevrolet Venture V6-3.4L VIN E 818

Locations View

Lower right rear of the engine compartment, mounted to the right side of the transaxle
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 312
Chevrolet Venture V6-3.4L VIN E 819

Locations View
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 313
Chevrolet Venture V6-3.4L VIN E 820

Locations View

Auto Level Control (ALC) Air Inflator Solenoid Valve


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 314
Chevrolet Venture V6-3.4L VIN E 821

Locations View

Behind the left rear wheelhouse


Automatic Transmission Shift Lock Solenoid
Inside the steering column near the ignition switch
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 315
Chevrolet Venture V6-3.4L VIN E 822

Locations View
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 316
Chevrolet Venture V6-3.4L VIN E 823

Locations View
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 317
Chevrolet Venture V6-3.4L VIN E 824

Locations View

Evaporative Emissions (EVAP) Canister Purge Solenoid Valve


Top rear of the engine, below the ignition control module
Evaporative Emissions (EVAP) Canister Vent Solenoid Valve
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 318
Chevrolet Venture V6-3.4L VIN E 825

Locations View
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 319
Chevrolet Venture V6-3.4L VIN E 826

Locations View

Below the center of the vehicle, forward of the fuel tank


Starter Solenoid
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 320
Chevrolet Venture V6-3.4L VIN E 827

Locations View

Lower front of the engine, part of the starter motor assembly


TCC Pulse Width Modulation Solenoid (TCC PWM SOL) Valve
Inside the automatic transaxle
1-2 Shift Solenoid (1-2 SS Valve)
Inside the automatic transaxle
2-3 Shift Solenoid (2-3 SS Valve)
Inside the automatic transaxle
Air Inflator Switch
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 321
Chevrolet Venture V6-3.4L VIN E 828

Locations View

Behind the left rear wheelhouse


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 322
Chevrolet Venture V6-3.4L VIN E 829

Locations View
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 323
Chevrolet Venture V6-3.4L VIN E 830

Locations View
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 324
Chevrolet Venture V6-3.4L VIN E 831

Locations View

Cruise Control Switch


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 325
Chevrolet Venture V6-3.4L VIN E 832

Locations View

Part of the turn signal switch, on the turn signal lever


Headlamp Dimmer Switch
Part of the turn signal switch, mounted to the steering column
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 326
Chevrolet Venture V6-3.4L VIN E 833

Locations View
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 327
Chevrolet Venture V6-3.4L VIN E 834

Locations View
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 328
Chevrolet Venture V6-3.4L VIN E 835

Locations View
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 329
Chevrolet Venture V6-3.4L VIN E 836

Locations View
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 330
Chevrolet Venture V6-3.4L VIN E 837

Locations View

Door Lock Switch Plate (Door Mounted, Striker)


Mounted to the lower, front end of the rear side door
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 331
Chevrolet Venture V6-3.4L VIN E 838

Locations View
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 332
Chevrolet Venture V6-3.4L VIN E 839

Locations View

Driver Seat Belt Switch


Inside the right half of the driver seat belt
Engine Oil Level Indicator Switch
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 333
Chevrolet Venture V6-3.4L VIN E 840

Locations View

Center of the engine oil pan


Engine Oil Pressure Indicator Switch
Front of the engine, above the starter
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 334
Chevrolet Venture V6-3.4L VIN E 841

Locations View

Front Door Lock (Ajar Indicator Switch)


Part of the front door lock
Front Door Lock Cylinder Switch
Inside the front door
Front Door Lock Switch
In the front door armrest
Front Window Switch
In the armrest of the front door
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 335
Chevrolet Venture V6-3.4L VIN E 842

Locations View

Headlamp and IP Dimmer Switch


Left of the instrument cluster
Headlamp and IP Lamp Dimmer Switch
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 336
Chevrolet Venture V6-3.4L VIN E 843

Locations View

Left of the instrument cluster


Heated Seat Switch
Part of the rear window wiper/washer and multi-function switch
Horn Switch
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 337
Chevrolet Venture V6-3.4L VIN E 844

Locations View
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 338
Chevrolet Venture V6-3.4L VIN E 845

Locations View

Behind the inflatable restraint steering wheel module


Ignition Key Alarm Switch
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 339
Chevrolet Venture V6-3.4L VIN E 846

Locations View

Part of the steering column


Ignition Switch
Part of the steering column
Interior Lamp and Multi-function SW (Interior LPS Override SW)
Part of the interior lamp and multi-function switch
Interior Lamp and Multi-function Switch
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 340
Chevrolet Venture V6-3.4L VIN E 847

Locations View
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 341
Chevrolet Venture V6-3.4L VIN E 848

Locations View

Center in front of the roof headliner


Interior LP & Multi-function SW (Power Sliding Door On/Off SW)
Part of the interior lamp and multi-function switch
Interior LP & Multi-Function SW (PWR Sliding DR Open/Close SW)
Part of the interior lamp and multi-function switch
Interior LP and Multi-function SW (Rear Quarter Window SW)
Part of the interior lamp and multi-function switch
IP Compartment Lamp Switch
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 342
Chevrolet Venture V6-3.4L VIN E 849

Locations View

Inside of the IP compartment, part of the IP compartment lamp


Liftgate Door Lock (Ajar Indicator Switch)
Part of the liftgate door lock
Liftgate Door Lock Cylinder Switch
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 343
Chevrolet Venture V6-3.4L VIN E 850

Locations View

Inside the liftgate, above the license lamps


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 344
Chevrolet Venture V6-3.4L VIN E 851

Locations View
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 345
Chevrolet Venture V6-3.4L VIN E 852

Locations View

Outside Rearview Mirror Remote Control Switch


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 346
Chevrolet Venture V6-3.4L VIN E 853

Locations View

Mounted to the top front left front door armrest panel


Park Brake Switch
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 347
Chevrolet Venture V6-3.4L VIN E 854

Locations View

Lower left A-pillar, part of the park brake assembly


Passenger Seat Adjuster Switch
Mounted to the side of the base of the right front seat
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 348
Chevrolet Venture V6-3.4L VIN E 855

Locations View
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 349
Chevrolet Venture V6-3.4L VIN E 856

Locations View

Power Sliding Door Detent Switch


Inside the right rear door, mounted to the rear of the door
Power Sliding Door Detent Switch (+E58) RH
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 350
Chevrolet Venture V6-3.4L VIN E 857

Locations View

For a Description of RPO Code(s) shown in this image refer to the RPO Code List found at Vehicle/Application and ID See: Application and
ID/RPO Codes
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 351
Chevrolet Venture V6-3.4L VIN E 858

Locations View

Power Sliding Door Open/Close Switch (RH B-Pillar)


Middle of the right B-pillar
Radio Control Switches
Left and right sides of the inflatable restraint steering wheel module
Rear WDO Wiper/Washer and Multi-function SW (AUX Blower SW)
Part of the rear window wiper/washer and multi-function switch
Rear WDO Wiper/Washer and Multi-function SW (Heated Seat SW)
Part of the rear window wiper/washer and multi-function switch
Rear Window Wiper/Washer and Multi-function SW (Fog LP/TCC SW)
Part of the rear window wiper/washer and multi-function switch
Rear Window Wiper/Washer and Multi-function Switch
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 352
Chevrolet Venture V6-3.4L VIN E 859

Locations View

Center of the IP, below the radio


Seat Adjuster Switch
Mounted to the side of the base of the seat
Seat Belt Switch
Inside the right half of the driver seat belt
Sliding Door Jamb Switch
Mounted to the rear opening of the rear side door
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 353
Chevrolet Venture V6-3.4L VIN E 860

Locations View
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 354
Chevrolet Venture V6-3.4L VIN E 861

Locations View

Stop Lamp Switch


Mounted to the brake pedal support
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 355
Chevrolet Venture V6-3.4L VIN E 862

Locations View
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 356
Chevrolet Venture V6-3.4L VIN E 863

Locations View
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 357
Chevrolet Venture V6-3.4L VIN E 864

Locations View
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 358
Chevrolet Venture V6-3.4L VIN E 865

Locations View

TCC Brake Switch


Mounted to the brake pedal support, connector 2 of the stop lamp switch
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 359
Chevrolet Venture V6-3.4L VIN E 866

Locations View

Transaxle Range Switch


Rear left side of the engine compartment, mounted to the top of the transaxle
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 360
Chevrolet Venture V6-3.4L VIN E 867

Locations View

Turn Sig. & HDLP Dimmer SW & W/S Wiper & W/S Washer SW
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 361
Chevrolet Venture V6-3.4L VIN E 868

Locations View

Inside the steering column


Turn Signal Lever (Cruise Control Switch)
Left side of the steering column, part of the turn signal switch
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 362
Chevrolet Venture V6-3.4L VIN E 869

Locations View

Windshield wiper/washer switch


Part of the turn signal switch, on the steering column
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 363
Chevrolet Venture V6-3.4L VIN E 870

Locations View
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 364
Chevrolet Venture V6-3.4L VIN E 871

Locations View
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 365
Chevrolet Venture V6-3.4L VIN E 872

Locations View
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 366
Chevrolet Venture V6-3.4L VIN E 873

Locations View
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 367
Chevrolet Venture V6-3.4L VIN E 874

Locations View
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 368
Chevrolet Venture V6-3.4L VIN E 875

Locations View
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 369
Chevrolet Venture V6-3.4L VIN E 876

Locations View
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 370
Chevrolet Venture V6-3.4L VIN E 877
Locations View

Locations View
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 371
Chevrolet Venture V6-3.4L VIN E 878

Locations View
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 372
Chevrolet Venture V6-3.4L VIN E 879

Locations View
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 373
Chevrolet Venture V6-3.4L VIN E 880

Locations View
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 374
Chevrolet Venture V6-3.4L VIN E 881

Locations View
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 375
Chevrolet Venture V6-3.4L VIN E 882

Locations View
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 376
Chevrolet Venture V6-3.4L VIN E 883

Locations View
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 377
Chevrolet Venture V6-3.4L VIN E 884

Locations View
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 378
Chevrolet Venture V6-3.4L VIN E 885

Locations View
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 379
Chevrolet Venture V6-3.4L VIN E 886

Locations View
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 380
Chevrolet Venture V6-3.4L VIN E 887

Locations View
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 381
Chevrolet Venture V6-3.4L VIN E 888

Locations View
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 382
Chevrolet Venture V6-3.4L VIN E 889

Locations View
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 383
Chevrolet Venture V6-3.4L VIN E 890

Locations View
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 384
Chevrolet Venture V6-3.4L VIN E 891

Locations View
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 385
Chevrolet Venture V6-3.4L VIN E 892

Locations View
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 386
Chevrolet Venture V6-3.4L VIN E 893

Locations View
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 387
Chevrolet Venture V6-3.4L VIN E 894

Locations View
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 388
Chevrolet Venture V6-3.4L VIN E 895

Locations View

Locations View
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 389
Chevrolet Venture V6-3.4L VIN E 896

Locations View
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 390
Chevrolet Venture V6-3.4L VIN E 897

Locations View
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 391
Chevrolet Venture V6-3.4L VIN E 898

Locations View
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 392
Chevrolet Venture V6-3.4L VIN E 899

Locations View
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 393
Chevrolet Venture V6-3.4L VIN E 900

Locations View
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 394
Chevrolet Venture V6-3.4L VIN E 901

Locations View

Data Link Connector (DLC)


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 395
Chevrolet Venture V6-3.4L VIN E 902

Locations View
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 396
Chevrolet Venture V6-3.4L VIN E 903

Locations View

Below the steering column, bottom of the knee bolster.


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 397
Chevrolet Venture V6-3.4L VIN E 904

Locations View
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 398
Chevrolet Venture V6-3.4L VIN E 905

Locations View
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 399
Chevrolet Venture V6-3.4L VIN E 906

Locations View
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 400
Chevrolet Venture V6-3.4L VIN E 907

Locations View
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 401
Chevrolet Venture V6-3.4L VIN E 908

Locations View
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 402
Chevrolet Venture V6-3.4L VIN E 909

Locations View
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 403
Chevrolet Venture V6-3.4L VIN E 910

Locations View
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 404
Chevrolet Venture V6-3.4L VIN E 911

Locations View
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 405
Chevrolet Venture V6-3.4L VIN E 912

Locations View
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 406
Chevrolet Venture V6-3.4L VIN E 913

Locations View
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 407
Chevrolet Venture V6-3.4L VIN E 914

Locations View
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 408
Chevrolet Venture V6-3.4L VIN E 915

Locations View
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 409
Chevrolet Venture V6-3.4L VIN E 916

Locations View
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 410
Chevrolet Venture V6-3.4L VIN E 917

Locations View
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 411
Chevrolet Venture V6-3.4L VIN E 918

Locations View
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 412
Chevrolet Venture V6-3.4L VIN E 919

Locations View
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 413
Chevrolet Venture V6-3.4L VIN E 920

Locations View
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 414
Chevrolet Venture V6-3.4L VIN E 921

Locations View
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 415
Chevrolet Venture V6-3.4L VIN E 922

Locations View
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 416
Chevrolet Venture V6-3.4L VIN E 923

Locations View
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 417
Chevrolet Venture V6-3.4L VIN E 924

Locations View
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 418
Chevrolet Venture V6-3.4L VIN E 925

Locations View
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 419
Chevrolet Venture V6-3.4L VIN E 926

Locations View
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 420
Chevrolet Venture V6-3.4L VIN E 927

Locations View
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 421
Chevrolet Venture V6-3.4L VIN E 928

Locations View
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 422
Chevrolet Venture V6-3.4L VIN E 929

Locations View
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 423
Chevrolet Venture V6-3.4L VIN E 930

Locations View
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 424
Chevrolet Venture V6-3.4L VIN E 931

Locations View
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 425
Chevrolet Venture V6-3.4L VIN E 932

Locations View
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 426
Chevrolet Venture V6-3.4L VIN E 933

Locations View
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 427
Chevrolet Venture V6-3.4L VIN E 934

Locations View
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 428
Chevrolet Venture V6-3.4L VIN E 935

Locations View
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 429
Chevrolet Venture V6-3.4L VIN E 936

Locations View

Locations View
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 430
Chevrolet Venture V6-3.4L VIN E 937

Locations View
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 431
Chevrolet Venture V6-3.4L VIN E 938

Locations View
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 432
Chevrolet Venture V6-3.4L VIN E 939

Locations View
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 433
Chevrolet Venture V6-3.4L VIN E 940

Locations View
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 434
Chevrolet Venture V6-3.4L VIN E 941

Locations View
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 435
Chevrolet Venture V6-3.4L VIN E 942

Locations View
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 436
Chevrolet Venture V6-3.4L VIN E 943

Locations View
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 437
Chevrolet Venture V6-3.4L VIN E 944

Locations View
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 438
Chevrolet Venture V6-3.4L VIN E 945

Locations View

Locations View
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 439
Chevrolet Venture V6-3.4L VIN E 946

Locations View
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 440
Chevrolet Venture V6-3.4L VIN E 947
Locations View

Locations View
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 441
Chevrolet Venture V6-3.4L VIN E 948

Locations View
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 442
Chevrolet Venture V6-3.4L VIN E 949

Locations View
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 443
Chevrolet Venture V6-3.4L VIN E 950

Locations View
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 444
Chevrolet Venture V6-3.4L VIN E 951

Locations View
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 445
Chevrolet Venture V6-3.4L VIN E 952

Locations View
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 446
Chevrolet Venture V6-3.4L VIN E 953

Locations View
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 447
Chevrolet Venture V6-3.4L VIN E 954

Locations View
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 448
Chevrolet Venture V6-3.4L VIN E 955

Locations View
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 449
Chevrolet Venture V6-3.4L VIN E 956

Locations View
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 450
Chevrolet Venture V6-3.4L VIN E 957

Locations View
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 451
Chevrolet Venture V6-3.4L VIN E 958

Locations View
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 452
Chevrolet Venture V6-3.4L VIN E 959

Locations View
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 453
Chevrolet Venture V6-3.4L VIN E 960

Locations View
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 454
Chevrolet Venture V6-3.4L VIN E 961

Locations View
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 455
Chevrolet Venture V6-3.4L VIN E 962

Locations View
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 456
Chevrolet Venture V6-3.4L VIN E 963

Locations View
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 457
Chevrolet Venture V6-3.4L VIN E 964

Locations View
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 458
Chevrolet Venture V6-3.4L VIN E 965
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 459
Chevrolet Venture V6-3.4L VIN E 966

Locations View
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 460
Chevrolet Venture V6-3.4L VIN E 967

Locations View
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 461
Chevrolet Venture V6-3.4L VIN E 968

Locations View
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 462
Chevrolet Venture V6-3.4L VIN E 969

Locations View
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 463
Chevrolet Venture V6-3.4L VIN E 970

Locations View
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 464
Chevrolet Venture V6-3.4L VIN E 971

Locations View
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 465
Chevrolet Venture V6-3.4L VIN E 972

Locations View
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 466
Chevrolet Venture V6-3.4L VIN E 973

Locations View
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 467
Chevrolet Venture V6-3.4L VIN E 974

Locations View
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 468
Chevrolet Venture V6-3.4L VIN E 975

Locations View
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 469
Chevrolet Venture V6-3.4L VIN E 976

Locations View
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 470
Chevrolet Venture V6-3.4L VIN E 977

Locations View
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 471
Chevrolet Venture V6-3.4L VIN E 978

Locations View
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 472
Chevrolet Venture V6-3.4L VIN E 979

Locations View
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 473
Chevrolet Venture V6-3.4L VIN E 980

Locations View
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 474
Chevrolet Venture V6-3.4L VIN E 981

Locations View
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 475
Chevrolet Venture V6-3.4L VIN E 982

Locations View
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 476
Chevrolet Venture V6-3.4L VIN E 983

Locations View
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 477
Chevrolet Venture V6-3.4L VIN E 984

Locations View

Locations View
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 478
Chevrolet Venture V6-3.4L VIN E 985

Locations View
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 479
Chevrolet Venture V6-3.4L VIN E 986

Locations View
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 480
Chevrolet Venture V6-3.4L VIN E 987

Locations View
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 481
Chevrolet Venture V6-3.4L VIN E 988

Locations View

C101
(20 cavities) IP wiring harness to the engine wiring harness, in the lower left side of the engine compartment, near the EBCM
C102
(16 cavities) Engine wiring harness to the fuel injector wiring harness, top of the engine, near the generator next to C108
C105
(4 cavities) Engine wiring harness to the engine coolant fan wiring harness, behind the engine coolant fan 1 (left)
C111
(14 cavities) Engine wiring harness to the automatic transaxle wiring harness, lower left side of the engine compartment, front of the automatic
transaxle
C120
(3 cavities) IP wiring harness to the forward lamp wiring harness, between the battery and the windshield fluid reservoir
C171
(2 cavities) IP wiring harness to the left wheel speed sensor wiring harness, below the air cleaner assembly, mounted to the left inner fender
C172
(2 cavities) IP wiring harness to the right wheel speed sensor wiring harness, below the windshield fluid reservoir
C200
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 482
Chevrolet Venture V6-3.4L VIN E 989

Locations View

(56 cavities) IP wiring harness to the right side of the body wiring harness, behind the right side of the IP compartment, below P100
C201
(48 cavities) IP wiring harness to the steering column wiring harness, mounted to the left side of the steering column near the base
C203
(56 cavities) IP wiring harness to the left side of the body wiring harness, left side of the steering column, below P101
C205
(4 cavities) IP wiring harness to the steering wheel radio control wiring harness, mounted to the left side of the steering column near the base
C215
(2 cavities) Inflatable restraint wiring harness to the inflatable restraint steering wheel module wiring harness, mounted to the left side of the
steering column near base
C216
(2 cavities) Inflatable restraint wiring harness to the inflatable restraint P module wiring harness, near the front right side of the IP compartment
C217
(8 cavities) Video Entertainment harness to the video cassette player (VCP) jumper harness behind the VCP
C290
(1 cavity) Antenna coaxial cable wiring harness to the antenna coaxial cable wiring harness, behind the IP compartment
C301
(10 cavities) Body wiring harness to the left side door I wiring harness, behind the left kick panel, left of the parking brake
C302
(16 cavities) Body wiring harness to the right front side door wiring harness, behind the right kick panel
C303
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 483
Chevrolet Venture V6-3.4L VIN E 990
(16 cavities) Body wiring harness to the left front side door wiring harness, behind the left kick panel, left of the parking brake
C304
(10 cavities) Body wiring harness to the right front side door wiring harness, behind the right kick panel
C305
(12 cavities) Body wiring harness to the electronic brake control wiring harness and fuel sender wiring harness, mounted as a pass through, beneath
the vehicle behind the driver seat
C306
(2 cavities) Electronic brake control wiring harness to the right rear wheel speed sensor wiring harness, under the right side of the vehicle, front of
the right rear wheel
C308
(23 cavities) Body wiring harness to the roof wiring harness, inside the right B-pillar, behind the lower trim
C309
(2 cavities) Electronic Brake control wiring harness to the left rear wheel speed sensor wiring harness, under the left side of the vehicle, front of the
left rear wheel
C313
(2 cavities) Body wiring harness to the driver seat adjuster switch wiring harness, under the driver seat
C314
(2 cavities) Body wiring harness to the passenger seat adjuster switch wiring harness, under the passenger seat
C315
(4 cavities) Body wiring harness to the driver seat heater module wiring harness, under the driver seat

C316
(4 cavities) Body wiring harness to the passenger seat heater module wiring harness, under the passenger seat
C326
(4 cavities) Inside overhead console, in front of the video display bracket assembly, tucked underneath the headliner
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 484
Chevrolet Venture V6-3.4L VIN E 991

Locations View
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 485
Chevrolet Venture V6-3.4L VIN E 992

Locations View

C328
(8 cavities) Inside overhead console, in front of the video display bracket assembly, tucked underneath the headliner
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 486
Chevrolet Venture V6-3.4L VIN E 993

Locations View
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 487
Chevrolet Venture V6-3.4L VIN E 994

Locations View

C396
(1 cavity) Antenna coaxial cable wiring harness to the window radio antenna lead, above the roof headliner, center of the windshield
C400
(2 cavities) Body wiring harness to the liftgate wiring harness, above the right rear side of the roof headliner, near P406 and the liftgate
C401
(4 cavities) Body wiring harness to the liftgate wiring IP harness, above the left rear side of the roof headliner, near P405 and the liftgate
C402
(8 cavities) Body wiring harness to the liftgate wiring harness, above the right rear side of the roof headliner, near P406 and the liftgate
C403
(3 cavities) Body wiring harness to the liftgate wiring harness, above the left rear side of the roof headliner, near P405 and the liftgate
C405
(10 cavities) Body wiring harness to the auto level control wiring harness, behind the left quarter panel, behind the left rear wheelhouse
C407 Domestic
(6 cavities) Auto level control wiring harness to the trailer rear wiring harness, beneath the vehicle, near P403, near the left rear wheelhouse
C407 Export
(8 cavities) Auto level control wiring harness to the trailer rear wiring harness, beneath the vehicle, near P403, near the left rear wheelhouse
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 488
Chevrolet Venture V6-3.4L VIN E 995

Locations View
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 489
Chevrolet Venture V6-3.4L VIN E 996

Locations View
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 490
Chevrolet Venture V6-3.4L VIN E 997

Locations View
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 491
Chevrolet Venture V6-3.4L VIN E 998

Locations View
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 492
Chevrolet Venture V6-3.4L VIN E 999

Locations View
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 493
Chevrolet Venture V6-3.4L VIN E 1000

Locations View
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 494
Chevrolet Venture V6-3.4L VIN E 1001

Locations View
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 495
Chevrolet Venture V6-3.4L VIN E 1002

Locations View
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 496
Chevrolet Venture V6-3.4L VIN E 1003

Locations View
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 497
Chevrolet Venture V6-3.4L VIN E 1004

Locations View
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 498
Chevrolet Venture V6-3.4L VIN E 1005

Locations View
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 499
Chevrolet Venture V6-3.4L VIN E 1006

Locations View
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 500
Chevrolet Venture V6-3.4L VIN E 1007

Locations View
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 501
Chevrolet Venture V6-3.4L VIN E 1008

Locations View
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 502
Chevrolet Venture V6-3.4L VIN E 1009

Locations View
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 503
Chevrolet Venture V6-3.4L VIN E 1010

Locations View
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 504
Chevrolet Venture V6-3.4L VIN E 1011

Locations View
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 505
Chevrolet Venture V6-3.4L VIN E 1012

Locations View
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 506
Chevrolet Venture V6-3.4L VIN E 1013

Locations View
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 507
Chevrolet Venture V6-3.4L VIN E 1014

Locations View
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 508
Chevrolet Venture V6-3.4L VIN E 1015

Locations View
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 509
Chevrolet Venture V6-3.4L VIN E 1016

Locations View
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 510
Chevrolet Venture V6-3.4L VIN E 1017

Locations View
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 511
Chevrolet Venture V6-3.4L VIN E 1018

Locations View
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 512
Chevrolet Venture V6-3.4L VIN E 1019

Locations View
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 513
Chevrolet Venture V6-3.4L VIN E 1020

Locations View

G100
Battery grounded to the right inner fender, near the battery
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 514
Chevrolet Venture V6-3.4L VIN E 1021

Locations View

G101
Front of the vehicle, right of the left headlamp, on the front upper crossmember
G102
Right side of the engine compartment, right inner fender, near the battery
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 515
Chevrolet Venture V6-3.4L VIN E 1022

Locations View

G111
Engine compartment, left of the starter, along with the battery ground
G113
Engine compartment, left of the starter, along with the battery ground
G114
Engine compartment, left and above the starter, near the starter solenoid
G117
Engine compartment, left and above the starter, near the starter solenoid
G200
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 516
Chevrolet Venture V6-3.4L VIN E 1023

Locations View

Right side of the IP, secured on the underside of the cross car beam, left of the heater-A/C vent
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 517
Chevrolet Venture V6-3.4L VIN E 1024

Locations View

G210
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 518
Chevrolet Venture V6-3.4L VIN E 1025

Locations View

Left side of the front floor console bracket


G301
Secured to the inside of the lower left B-pillar
G302
Secured near the base of the right B-pillar
G390
Antenna coaxial cable secured with the clamp, grounding the coaxial shield to the top of the windshield frame, right of the mirror
G401
Secured to the lower left D-pillar
G402
Secured to the lower right D-pillar
SP200 - SP299
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 519
Chevrolet Venture V6-3.4L VIN E 1026

Locations View

Below the steering column, bottom of the knee bolster


S105
Engine harness, top right side radiator approximately 20 cm (8 in) from the engine coolant fan 1 (right) motor breakout
S106
Engine harness, front left side of the engine compartment approximately 10 cm (4 in) from the PCM breakout
S107
Engine harness, center of the engine approximately 4 cm (2 in) from the camshaft position sensor breakout
S108
Engine harness, front left side of the engine compartment approximately 8 cm (3 in) from the PCM breakout
S109
Fuel injector harness, center of the engine approximately 16 cm (6 in) from C102
S110
Fuel injector harness, center of the engine approximately 14 cm (4 in) from C102
S115
Automatic transaxle harness, inside automatic transaxle housing approximately 42 cm (17 in) from the automatic transaxle fluid temperature sensor
S122
Engine harness, top left side of the radiator approximately 25 cm (10 in) from the engine coolant fan 1 (right) motor breakout
S123
Forward lamp harness, right front of the vehicle approximately 10 cm (4 in) from the right fog lamp breakout
S124
Forward lamp harness, left front of the vehicle approximately 7 cm (3 in) from the left fog lamp breakout
S146
Engine harness, center of the engine approximately 10 cm (4 in) from the engine coolant fan 1 (right) motor breakout
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 520
Chevrolet Venture V6-3.4L VIN E 1027
S155
Engine harness, front of the engine approximately 14 cm (6 in) from the knock sensor breakout
S167
Engine harness, front left side of the engine approximately 5 cm (2 in) PCM breakout
S201
IP harness, right side of the IP approximately 21 cm (8 in) from the radio breakout
S202
IP harness, left side of the IP approximately 15 cm (6 in) from the rear window wiper/washer and multi-function switch breakout
S203
IP harness, right side of the IP approximately 9 cm (4 in) from the radio breakout
S204
IP harness, right side of the IP approximately 10 cm (4 in) from the radio breakout
S205
IP harness, left side of the IP approximately 8 cm (3 in) from the hazard lamp/turn signal flasher breakout
S207
IP harness, left side of IP approximately 4 cm (2 in) from the hazard lamp/turn signal flasher breakout
S208
Video entertainment harness
S209
IP harness, center of the IP approximately 8 cm (3 in) from the security indicator lamp breakout
S210
IP harness, center of the IP approximately 4 cm (2 in) from the security indicator lamp breakout
S211
IP harness, left side of the IP approximately 15 cm (6 in) from the radio and the rear window wiper/washer and multi-function switch breakout
S213
IP harness, center of IP approximately 72 cm (28 in) from the cigar lighter
S215
IP harness, left side of IP approximately 13 cm (5 in) from headlamp switch breakout
S219
IP harness, left side of the IP approximately 10 cm (4 in) from the radio and the rear window wiper/washer and multi-function switch breakout
S221
IP harness, left side of the IP approximately 4 cm (2 in) from the headlamp switch breakout
S223
IP harness, left side of the P approximately 6 cm (2 in) from the radio and rear window wiper/washer and multi-function switch breakout
S225
IP harness, center of the IP approximately 8 cm (3 in)
S227
IP harness, center of the IP approximately 4 cm (2 in) from the security indicator lamp breakout
S228
IP harness, right side of the IP approximately 19 cm (7 in) from the radio breakout
S230
IP harness, right side of the IP approximately 4 cm (2 in) from the rear window wiper/washer and multi-function switch breakout
S232
IP harness, right side of the IP approximately 17 cm (7 in) from the radio breakout
S233
IP harness, left side of the IP approximately 4 cm (2 in) from the radio breakout
S235
IP harness, left side of the IP approximately 21 cm (8 in) from P101
S236
Below left side of IP, near park brake
S237
IP harness, right side of the IP approximately 4 cm (2 in) from the C203 breakout
S238
IP harness, center of the P approximately 80 cm (31 in) from the cigar lighter connector
S239
IP harness, right side of the IP approximately 8 cm (3 in) from the C203 breakout
S242
IP harness, left side of the IP approximately 14 cm (6 in) from the radio and the rear window wiper/washer and multi-function switch breakout
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 521
Chevrolet Venture V6-3.4L VIN E 1028
S243
IP harness, center of the IP approximately 37 cm (15 in) from the radio and rear window wiper/washer and multi-function switch breakout
S245
IP harness, right side of the IP approximately 5 cm (2 in) from the radio IP breakout, within the radio breakout
S247
IP harness, center of the IP approximately 31 cm (12 in) from the radio
S249
IP harness, right side of the IP approximately 14 cm (6 in) from P100
S252
IP harness, center of the IP approximately 76 cm (30 in) from the cigar lighter
S259
IP harness, right side of the IP approximately 3 cm (1 in) from the cigar lighter breakout
S261
IP harness, right side of the IP at the electric air inlet actuator breakout
S262
IP harness, right side of the IP approximately 4 cm (2 in) from the blower motor resistor breakout
S263
IP harness, right side of the IP at the electric air inlet actuator breakout
S264
IP harness, right side of the IP approximately 16 cm (6 in) from the relay center breakout
S266
IP harness, left side of the P approximately 24 cm (9 in) from the radio and the rear window wiper/washer and multi-function switch breakout
S268
IP harness, right side of the IP approximately 29 cm (11 in) from the relay center breakout
S270
IP harness, right side of the IP approximately 6 (2 in) from the relay center breakout
S272
IP harness, right side of the P approximately 2 cm (1 in) from the relay center breakout
S274
IP harness, right side of the IP approximately 4 cm (2 in) from the BCM breakout
S275
IP harness, right side of the IP approximately 6 cm (2.5 in) from the BCM breakout
S276
IP harness, right side of the IP approximately 8 cm (3 in) from the BCM breakout
S278
IP harness, right side of the IP approximately 12 cm (5 in) from the BCM breakout
S279
IP harness, right side of the IP approximately 12 cm (5 in) from the hazard lamp/turn signal flasher breakout
S280
IP harness, right side of the IP approximately 10 cm (4 in) from P100
S282
IP harness, left side of the IP approximately 4 cm (2 in) from the cigar lighter breakout
S284
IP harness, right side of the IP approximately 6 cm (2 in) from P100
S301
Roof harness, approximately 65 cm (24 in) from the driver information display breakout
S302
Body harness, right front door approximately 7 cm (3 in) from the inflatable restraint sensing and diagnostic module breakout
S303
Body harness, front of the right B-pillar approximately 26 cm (10 in) from the inflatable restraint sensing and diagnostic module breakout
S304
Body harness, right front door approximately 28 cm (11 in) from the inflatable restraint sensing and diagnostic module breakout
S305
Dome lamp wiring harness to body wiring harness, approximately 30 cm (12 in) from driver information display
S307
Body harness, right front door approximately 4 cm (2 in) from C302 breakout
S308
Body harness, left front door approximately 39 cm (15 in) from the seat belt switch breakout
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 522
Chevrolet Venture V6-3.4L VIN E 1029
S309
Body harness, forward of the right front door approximately 7 cm (3 in) from the C302 breakout
S311
Body harness, under the right front door sill approximately 13 cm (5 in) from the C302 breakout
S312
Body harness, front of the right hand B-pillar approximately 31 cm (12 in) front of the inflatable restraint sensing and diagnostic module breakout
S314
Body harness, under the right front seat approximately 2 cm (1 in) from the inflatable restraint sensing and diagnostic module breakout
S315
Body harness, under the right front seat approximately 8 cm (3 in) from the inflatable restraint sensing and diagnostic module breakout
S316
Body harness, front of the right B-pillar approximately 34 cm (13 in) from the inflatable restraint sensing and diagnostic module breakout
S317
Body harness, under right front door sill, approximately 17 cm (7 in) from C302 breakout
S318
Body harness, under the right front door sill approximately 17 cm (7 in) C302 breakout
S319
Body harness, under the right front door sill approximately 17 cm (7 in) C302 breakout
S320
Body harness, near the base of the right B-pillar approximately 33 cm (13 in) forward of the right door lock switch plate (pillar mounted, plunger)
breakout
S323
Body harness, under the left front seat approximately 7 cm (3 in) from the seat belt switch breakout
S324
Body harness, top/forward area of the left rear wheel well approximately 5 cm (2 in) behind the second oval clamp
S325
Body harness, front of the left B-pillar approximately 7 cm (3 in) from the left sliding door jamb switch breakout
S326
Body harness, top/forward area of the left rear wheel well approximately 13 cm (5 in) behind the second oval clamp
S327
Body harness, under the left front seat approximately 13 cm (5 in) from the seat belt switch breakout
S328
Body harness, between the left D-pillar and the wheel well approximately 32 cm (13 in) forward of the G401 breakout
S329
Fuel sender harness, between C305 and the fuel tank approximately 20 cm (8 in) from C305
S330
Body harness, left of B-pillar, approximately 40 cm (16 in) from seat belt switch breakout
S331
Body harness, front of the left B-pillar approximately 59 cm (23 in) from the G301 breakout
S333
Body harness, front of the left B-pillar approximately 39 cm (15 in) from the G301 breakout
S337
Body harness, rear of the left B-pillar base approximately 8 cm (3 in) from the P401 breakout
S339
Body harness, front of the left B-pillar approximately 26 cm (10 in) from the G301 breakout
S341
Body harness, in front of the left wheelhouse approximately 13 cm (5 in) from the radio rear speaker amplifier breakout
S343
Body harness, in front of the left wheelhouse approximately 40 cm (16 in) from the radio rear speaker amplifier breakout
S345
Body harness, in front of the left rear wheelhouse approximately 48 cm (19 in) from the left sliding door jamb switch
S390
Roof harness, overhead console approximately 10 cm (4 in) from the right sunshade lighted vanity mirror breakout
S392
Roof harness, right B-pillar approximately 27 cm (10 in) from the power sliding door open/close switch (right B-pillar)
S393
Roof harness, right side of the overhead console approximately 20 cm (8 in) from the G302 breakout
S395
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 523
Chevrolet Venture V6-3.4L VIN E 1030
Roof harness, right side of the overhead console approximately 13 cm (5 in) from the he power sliding door open/close switch (right B-pillar)
breakout
S397
Roof harness, right side of the overhead console approximately 7 cm (3 in) from the G302 breakout
S399
Sunroof harness, front of the overhead console approximately 10 cm (4 in) from the sunroof control module
S403
Body harness, left rear of the body on top of the wheel well approximately 13 cm (5 in) from the top and rear clips
S405
Body harness, left rear of the body approximately 4 cm (2 in) from the P401 breakout
S406
Body harness, left rear of the body approximately 17 cm (7 in) from the P401 breakout
S407
Body harness, left rear of the body approximately 13 cm (5 in) from the P401 breakout
S409
Body harness, left rear of the body approximately 7 cm (3 in) from the P401 breakout
S411
Body harness, left rear of the body approximately 7 cm (3 in) from the P401 breakout
S412
Body harness, left rear of the body approximately 8 cm (3.5 in) from the P401 breakout
S415
Body harness, left rear of the body approximately 11 cm (4 in) from the P401 breakout
S419
Body harness, left rear of the body approximately 21 cm (8 in) from the P401 breakout
S423
Body harness, left rear of the body approximately 54 cm (20 in) from the C403 breakout
S427
Body harness, left rear of the body approximately 41 cm (16 in) from the C403 breakout
S431
Body harness, left rear of the body approximately 4 cm (2 in) from the P401 breakout
S435
Body harness, left rear of the body approximately 26 cm (10 in) from the P401 breakout
S440
Auto level control harness, left rear of the body approximately 24 cm (9 in) from P403
S441
Auto level control harness, left rear of the body approximately 24 cm (9 in) from P403
S443
Auto level control harness, left rear of the body approximately 20 cm (8 in) from P403
S445
Auto level control harness, left rear of the body approximately 16 cm (6 in) from P403
S457
Liftgate harness, center of the liftgate approximately 7 cm (3 in) from the liftgate lock (door ajar switch) breakout
S460
Liftgate harness center of the liftgate approximately 7 cm (3 in) from the liftgate lock cylinder switch breakout
S504
Left door harness, left door approximately 10 cm (4 in) from the left window switch breakout
S506
Left door harness, left door approximately 35 cm (3 in) from the left window switch
S604
Right door harness, between P600 and the right front speaker breaker
S604 (W/AB5)
Right door harness, right door approximately 10 cm (4 in) from the right window switch breakout
S606
Right door harness, right door approximately 35 cm (13 in) from the right window switch
S800 - S899
Sliding door harness, inside the right rear side door approximately 11 cm (4 in) from the right rear door latch release actuator breakout
P100
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 524
Chevrolet Venture V6-3.4L VIN E 1031

Locations View

On the right side of the bulkhead, left of the right strut tower
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 525
Chevrolet Venture V6-3.4L VIN E 1032

Locations View

P400
Behind the right taillamp
P401
Behind the left taillamp
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 526
Chevrolet Venture V6-3.4L VIN E 1033

Locations View
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 527
Chevrolet Venture V6-3.4L VIN E 1034

Locations View

P405
Between the left side of the liftgate and the roof
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 528
Chevrolet Venture V6-3.4L VIN E 1035

Locations View

P406
Between the right side of the liftgate and the roof
P500
Between the left A-pillar and the left front door
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 529
Chevrolet Venture V6-3.4L VIN E 1036

Locations View

P600 - P699
Between the right A-pillar and the right front door
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 530
Chevrolet Venture V6-3.4L VIN E 1037

Locations View
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 531
Chevrolet Venture V6-3.4L VIN E 1038

Harness Routing Views (Auxiliary Video Module (AVM))


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 532
Chevrolet Venture V6-3.4L VIN E 1039

Harness Routing Views (LH B-Pillar)


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 533
Chevrolet Venture V6-3.4L VIN E 1040

Harness Routing Views (RH B-Pillar)


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 534
Chevrolet Venture V6-3.4L VIN E 1041

Harness Routing Views (Base Of Steering Column)


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 535
Chevrolet Venture V6-3.4L VIN E 1042

Harness Routing Views (Behind Rear Left Wheelhouse)


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 536
Chevrolet Venture V6-3.4L VIN E 1043

Harness Routing Views (Below Driver's Seat)


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 537
Chevrolet Venture V6-3.4L VIN E 1044

Harness Routing Views (Below RH Side Of IP)


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 538
Chevrolet Venture V6-3.4L VIN E 1045

Harness Routing Views (LF Door (RH Side Similar))


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 539
Chevrolet Venture V6-3.4L VIN E 1046

Harness Routing Views (Front of Engine Compartment)


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 540
Chevrolet Venture V6-3.4L VIN E 1047

Locations View
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 541
Chevrolet Venture V6-3.4L VIN E 1048

Locations View
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 542
Chevrolet Venture V6-3.4L VIN E 1049

Harness Routing Views (Front, Right Side of Engine Compartment)


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 543
Chevrolet Venture V6-3.4L VIN E 1050

Harness Routing Views (Fuel Tank, Below LH Side, Middle of Vehicle)


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 544
Chevrolet Venture V6-3.4L VIN E 1051

Locations View
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 545
Chevrolet Venture V6-3.4L VIN E 1052

Harness Routing Views (Interface Module)


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 546
Chevrolet Venture V6-3.4L VIN E 1053

Harness Routing Views (LH Side Of Engine Compartment


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 547
Chevrolet Venture V6-3.4L VIN E 1054

Harness Routing Views (LF of Engine Compartment)


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 548
Chevrolet Venture V6-3.4L VIN E 1055

Harness Routing Views (RF Wheel (LF Wheel Speed Sensor Similar))
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 549
Chevrolet Venture V6-3.4L VIN E 1056

Harness Routing Views(LH Side Of IP,Left Of Steering Column)


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 550
Chevrolet Venture V6-3.4L VIN E 1057

Harness Routing Views (Lower Front Of The Engine)


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 551
Chevrolet Venture V6-3.4L VIN E 1058

Locations View
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 552
Chevrolet Venture V6-3.4L VIN E 1059

Harness Routing Views (Right Quarter Panel (Rear Side Door Actuator Motor))
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 553
Chevrolet Venture V6-3.4L VIN E 1060

Locations View
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 554
Chevrolet Venture V6-3.4L VIN E 1061

Locations View
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 555
Chevrolet Venture V6-3.4L VIN E 1062

Harness Routing Views (Rear, Left Side of Engine Compartment)


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 556
Chevrolet Venture V6-3.4L VIN E 1063

Harness Routing Views (RH Side Of IP)


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 557
Chevrolet Venture V6-3.4L VIN E 1064

Harness Routing Views (RH Side of IP)


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 558
Chevrolet Venture V6-3.4L VIN E 1065

Harness Routing Views (RH Side Of IP, Bottom Of Cross Car Beam)
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 559
Chevrolet Venture V6-3.4L VIN E 1066

Harness Routing Views (LH Taillamp (RH Similar))


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 560
Chevrolet Venture V6-3.4L VIN E 1067

Harness Routing Views (Top, LH Side Of Rear Body)


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 561
Chevrolet Venture V6-3.4L VIN E 1068

Harness Routing Views (Top, RH Side of Engine Compartment)


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 562
Chevrolet Venture V6-3.4L VIN E 1069

Harness Routing Views (Underneath Rear of Vehicle)


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 563
Chevrolet Venture V6-3.4L VIN E 1070

Harness Routing Views (Video Cassette Player (VCP), Video Entertainment System (VES) Relay, And G210)
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 564
Chevrolet Venture V6-3.4L VIN E 1071

Harness Routing Views (Video Entertainment System (VES) Relay And Splices)
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 565
Chevrolet Venture V6-3.4L VIN E 1072

Locations View
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 566
Chevrolet Venture V6-3.4L VIN E 1073

Locations View
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 567
Chevrolet Venture V6-3.4L VIN E 1074

Locations View
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 568
Chevrolet Venture V6-3.4L VIN E 1075

Locations View
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 569
Chevrolet Venture V6-3.4L VIN E 1076

Locations View
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 1
Chevrolet Venture V6-3.4L VIN E 1077
Vehicle: Diagrams

Utility/Van Zoning Table

Utility/Van Zoning

All grounds, in-line connectors, pass-through grommets, and splices have identifying numbers that correspond to where they are located in the
vehicle. The following table explains the numbering system.
Electrical Symbols
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 2
Chevrolet Venture V6-3.4L VIN E 1078

Electrical Symbols (Part 1 Of 4)


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 3
Chevrolet Venture V6-3.4L VIN E 1079

Electrical Symbols (Part 2 Of 4)


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 4
Chevrolet Venture V6-3.4L VIN E 1080

Electrical Symbols (Part 3 Of 4)


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 5
Chevrolet Venture V6-3.4L VIN E 1081

Electrical Symbols (Part 4 Of 4)

Arrows and Symbols


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 6
Chevrolet Venture V6-3.4L VIN E 1082

This service manual uses various symbols in order to describe different service operations.
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 7
Chevrolet Venture V6-3.4L VIN E 1083

Conversion - English/Metric

Diagnostic Work Sheets


The GM Diagnostic Worksheet has been designed to improve communications between the service customer and the technician. The diagnostic
worksheet can provide the technician with more information than the conventional repair order, since it is filled out by the service customer. The
GM Diagnostic Worksheets are available to you at no cost. GM Service Bulletin 58-01-01 has information on how to order this diagnostic
worksheet.
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 8
Chevrolet Venture V6-3.4L VIN E 1084

Equivalents - Decimal And Metric (Part 1 Of 2)


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 9
Chevrolet Venture V6-3.4L VIN E 1085

Equivalents - Decimal And Metric (Part 2 Of 2)

Basic Knowledge Required


Without a basic knowledge of electricity, it will be difficult to use the diagnostic procedures contained in this section. You should understand the
basic theory of electricity and know the meaning of voltage (volts), current (amps) and resistance (ohms). You should understand what happens in
a circuit with an open or a shorted wire. You should be able to read and understand a wiring diagram.

Refer to Strategy Based Diagnosis in General Information in order to properly diagnose and repair the customer concern.
Checking Aftermarket Accessories
Do not connect aftermarket accessories into the following circuits:

CAUTION: Refer to SIR Service Precautions Caution in Service Precautions.

- SIR circuits, all such circuits are indicated on circuit diagrams with the SIR symbol.

NOTE: Refer to OBD II Symbol Description Notice in Service Precautions.

- OBDII circuits, all such circuits are indicated on circuit diagrams with the OBDII symbol.

Always check for aftermarket accessories (non-OEM) as the first step in diagnosing electrical problems. If the vehicle is so equipped, disconnect
the system to verify that these add-on accessories are not the cause of the problems.

Possible causes of vehicle problems related to aftermarket accessories include:


- Power feeds connected to points other than the battery.
- Antenna location.
- Transceiver wiring located too close to vehicle electronic modules or wiring.
- Poor shielding or poor connectors on antenna feed line.
- Check for recent service bulletins detailing installation guidelines for aftermarket accessories.
Circuit Breakers
A circuit breaker is a protective device that is designed to open the circuit when a current load is in excess of the rated breaker capacity. If there is a
short or other type of overload condition in the circuit, the excessive current will open the circuit between the circuit breaker terminals. Two types
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 10
Chevrolet Venture V6-3.4L VIN E 1086
of circuit breakers are used.

Circuit Breaker: This type opens when excessive current passes through it for a period of time. It closes again after a few seconds, and if the cause
of the high current is still present, it will open again. The circuit breaker will continue to cycle open and closed until the condition causing the high
current is removed.

Positive Temperature Coefficient (PTC) Circuit Breaker: This type greatly increases its resistance when excessive current passes through it.
The excessive current heats the PTC device, as the device heats its resistance increases. Eventually the resistance gets so high that the circuit is
effectively open. Unlike the ordinary circuit breaker the PTC unit will not reset until the circuit is opened, by removing the voltage from its
terminals. Once the voltage is removed the circuit breaker will re-close within a second or two.
Fuses

Circuit Protection - Fuses

Fuse Types

The fuse is the most common method of an automotive wiring circuit protection. Whenever there is an excessive amount of current flowing through
a circuit the fusible element will melt and create an open or incomplete circuit. Fuses are an one time protection device and must be replaced each
time the circuit is overloaded. To determine if a fuse is open, remove the suspected fuse and examine the element in the fuse for an open (break). If
not broken, also check for continuity using a J 39200 DMM or a continuity tester. If the element is open or continuity is suspect, replace the fuse
with one of equal current rating.
Fusible Link
Fusible link is wire designed to melt and break continuity when excessive current is applied. It is often located between or near the battery and
starter or electrical center. Use a continuity tester or a J 39200 DMM at each end of the wire containing the fusible link in order to determine if it is
broken. If broken, it must be replaced with fusible link of the same gage size.

Repairing a Fusible Link

IMPORTANT: Fusible links cut longer than 225 mm (approx. 9 inches) will not provide sufficient overload protection.

Refer to Splicing Copper Wire Using Splice Clips.

Circuit Testing
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 11
Chevrolet Venture V6-3.4L VIN E 1087
The Circuit Testing section contains the following diagnostic testing information. Using this information along with the diagnostic procedures will
identify the cause of the electrical malfunction.
- Using Connector Test Adapters
- Probing Electrical Connectors
- Troubleshooting with a Digital Multimeter
- Troubleshooting with a Test Lamp
- Using Fused Jumper Wires
- Measuring Voltage
- Measuring Voltage Drop
- Measuring Frequency
- Testing for Continuity
- Testing for Short to Ground
- Testing for a Short to Voltage
Connector Position Assurance (CPA)
The Connector Position Assurance (CPA) is a small plastic insert that first through the locking tabs of all the SIR/SRS system electrical connectors.
The CPA ensures that the connector halves cannot vibrate apart. You must have the CPA in place in order to ensure good contact between the
SIR/SRS mating terminals.

Inducing Intermittent Fault Conditions


In order to duplicate the customer's concern, it may be necessary to manipulate the wiring harness if the malfunction appears to be vibration related.
Manipulation of a circuit can consist of a wide variety of actions, including:
- Wiggling the harness
- Disconnecting a connector and reconnecting
- Stressing the mechanical connection of a connector
- Pulling on the harness or wire in order to identify a separation/break inside the insulation
- Relocating a harness or wires

All these actions should be performed with some goal in mind. For instance, with a scan tool connected, wiggling the wires may uncover a faulty
input to the control module. The snapshot option would be appropriate here. Refer to Scan Tool Snapshot Procedure. You may need to load the
vehicle in order to duplicate the concern. This may require the use of weights, floorjacks, jackstands, frame machines, etc. In these cases you are
attempting to duplicate the concern by manipulating the suspension or frame. This method is useful in finding harnesses that are too short and their
connectors pull apart enough to cause a poor connection. A DMM set to Peak Min/Max mode and connected to the suspect circuit while testing can
yield desirable results. Refer to Testing for Electrical Intermittents.

Certainly, using the senses of sight, smell, and hearing while manipulating the circuit can provide good results as well.

There may be instances where circuit manipulation alone won't meet the required criteria for the fault condition to appear. In such cases it may be
necessary to expose the suspect circuit to other conditions while manipulating the harness. Such conditions would include high moisture conditions,
along with exceptionally high or low temperatures. The following discusses how to expose the circuit to these kinds of conditions.

Salt Water Spray


Some compounds possess the ability to conduct electricity when dissolved in water such as ordinary salt. By mixing table salt with water in
sufficient quantities, you can enhance the conductive properties of water so that any circuit which may be sensitive to moisture will more readily
fail when liberally sprayed with this mixture.

Mixing 12 ounces of water with approximately 1 tablespoon of salt will yield a salt solution of 5%. Fill a normal spray bottle with this mixture.
This mixture is sufficient to enhance the water's own conductivity. This may cause the circuit to fail more easily when sprayed. Once the mixture
is completed, spray the suspect area liberally with the solution. Then, while monitoring either a scan tool or DMM, manipulate the harness as
discussed previously.

High Temperature Conditions


If the complaint tends to be heat related, you can simulate the condition using the J 25070 Heat Gun.

Using the heat gun, you can heat up the suspected area or component. Manipulate the harnesses under high temperature conditions while
monitoring the scan tool or DMM to locate the fault condition.

The high temperature condition may be achieved simply by test driving the vehicle at normal operating temperature. If a heat gun is unavailable,
consider this option to enhance your diagnosis. This option does not allow for the same control, however.

Low Temperature Conditions


Depending on the nature of the fault condition, placing a fan in front of the vehicle while the vehicle is in the shade can have the desired effect.

If this is unsuccessful, use local cooling treatments such as ice or a venturi type nozzle (one that provides hot or cold air). This type of tool is
capable of producing air stream temperatures down to 0°F from one end and 160°F from the other. This is ideally suited for localized cooling
needs.

Once the vehicle, component, or harness has been sufficiently cooled, manipulate the harness or components in an effort to duplicate the concern.

Intermittents
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 12
Chevrolet Venture V6-3.4L VIN E 1088
Most intermittent are caused by faulty electrical connections or wiring. Inspect for the following items:
- Wiring broken inside the insulation.
- Poor connection between the male and female terminal at a connector. Refer to Testing for Proper Terminal Contact below for the specific
procedure.
- Poor terminal to wire connection. Some conditions which fall under this description are poor crimps, poor solder joints, crimping over the
wire insulation rather than the wire itself and corrosion in the wire to terminal contact area, etc.
- Wire insulation which is rubbed through. This causes an intermittent short as the bare area touches other wiring or parts of the vehicle.
- Refer to Testing for Electrical Intermittents for test procedures to detect intermittent open, high resistance, short to ground, and short to
voltage conditions.

Testing for Proper Terminal Contact


It is important to test terminal contact at the component and any in-line connectors before replacing a suspect component. Mating terminals must
be inspected to ensure good terminal contact. A poor connection between the male and female terminal at a connector may be the result of
contamination or deformation.

Contamination may be caused by the connector halves being improperly connected. A missing or damaged connector seal, damage to the
connector itself, or exposing the terminals to moisture and dirt can also cause contamination. Contamination, usually in the underhood or
underbody connectors, leads to terminal corrosion, causing an open circuit or intermittently open circuit.

Deformation is caused by probing the mating side of a connector terminal without the proper adapter, improperly joining the connector halves, or
repeatedly separating and joining the connector halves. Deformation, usually to the female terminal contact tang, can result in poor terminal
contact causing an open or intermittently open circuit.

Round Wire Connectors


Follow the procedure below to test terminal contact of Metri-Pack or 56 series terminals. Refer to the J 38125-B Terminal Repair Kit or the J
38125-4 Instruction Manual for terminal identification.

Follow the procedure below in order to test terminal contact.


1. Separate the connector halves.
2. Visually inspect the connector halves for contamination. Contamination may result in a white or green build-up within the connector body or
between terminals. This causes high terminal resistance, intermittent contact, or an open circuit. An underhood or underbody connector that
shows signs of contamination should be replaced in its entirety: terminals, seals, and connector body.
3. Using an equivalent male terminal from the J 38125-B, test that the retention force is significantly different between a good terminal and a
suspect terminal. Replace the female terminal in question.

Flat Wire (Dock and Lock) Connectors


There are no serviceable parts for flat wire (dock and lock) connectors on the harness side or the component side.
Follow the procedure below in order to test terminal contact.
1. Remove the component in question.
2. Visually inspect each side of the connector for signs of contamination. Avoid touching either side of the connector as oil from your skin may
be a source of contamination as well.
3. Visually inspect the terminal bearing surfaces of the flat wire circuits for splits, cracks, or other imperfections that could cause poor terminal
contact. Visually inspect the component side connector to ensure that all of the terminals are uniform and free of damage or deformation.
4. Insert the appropriate adapter from the J 42675 Flat Wire Probe Adapter Kit on the flat wire harness connector in order to test the circuit in
question.

Measuring Frequency
NOTE: Refer to Test Probe Notice in Service Precautions.

The following procedure determines the frequency of a signal.

IMPORTANT: Connecting the DMM to the circuit before pressing the Hz button will allow the DMM to autorange to an appropriate range.

1. Apply power to the circuit.


2. Set the rotary dial of the DMM to the V (AC) position.
3. Connect the positive lead of the DMM to the circuit to be tested.
4. Connect the negative lead of the DMM to a good ground.
5. Press the Hz button on the DMM.
6. The DMM will display the frequency measured.
Measuring Voltage
NOTE: Refer to Test Probe Notice in Service Precautions.

The following procedure measures the voltage at a selected point in a circuit.


1. Disconnect the electrical harness connector for the circuit being tested, if necessary.
2. Enable the circuit and/or system being tested. Use the following methods:
- Turn ON the ignition, with the engine OFF.
- Turn ON the engine.
- Turn ON the circuit and/or system with a scan tool in Output Controls.
- Turn ON the switch for the circuit and/or system being tested.
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 13
Chevrolet Venture V6-3.4L VIN E 1089
3. Select the V (AC) or V (DC) position on the DMM.
4. Connect the positive lead of the DMM to the point of the circuit to be tested.
5. Connect the negative lead of the DMM to a good ground.
6. The DMM displays the voltage measured at that point.

Measuring Voltage Drop


NOTE: Refer to Test Probe Notice in Service Precautions.

The following procedure determines the difference in voltage potential between two points.

1. Set the rotary dial of the DMM to the V (DC) position.


2. Connect the positive lead of the DMM to one point of the circuit to be tested.
3. Connect the negative lead of the DMM to the other point of the circuit.
4. Operate the circuit.
5. The DMM displays the difference in voltage between the two points.

Probing Electrical Connectors


IMPORTANT: Always be sure to reinstall the Connector Position Assurance (CPA)and Terminal Position Assurance (TPA) when reconnecting
connectors or replacing terminals.

Frontprobe
Disconnect the connector and probe the terminals from the mating side (front) of the connector.

NOTE: Do not insert test equipment probes into any connector or fuse block terminal. The diameter of the test probes will deform most
terminals. A deformed terminal can cause a poor connection, which can result in system failures. Always use the J 35616-A Connector Test
Adapter Kit or the J 42675 Flat Wire Probe Adapter Kit in order to frontprobe terminals. Do not use paper clips or other substitutes as they can
damage terminals and cause incorrect measurements.

Backprobe
Do not disconnect the connector and probe the terminals from the harness side (back) of the connector.

IMPORTANT:
- Backprobe connector terminals only when specifically required in diagnostic procedures.
- Do not backprobe a sealed (Weather Pack(R)) connector, less than a 280 series Metri-Pack connector, a Micro-Pack connector, or a flat
wire (dock and lock) connector.
- Backprobing can be a source of damage to connector terminals. Use care in order to avoid deforming the terminal, either by forcing the
test probe too far into the cavity or by using too large of a test probe.
- After backprobing any connector, inspect for terminal damage. If terminal damage is suspected, test for proper terminal contact.

Salt Water Spray


Some compounds possess the ability to conduct electricity when dissolved in water such as ordinary salt. By mixing table salt with water in
sufficient quantities, you can enhance the conductive properties of water so that any circuit which may be sensitive to moisture will more readily
fail when liberally sprayed with this mixture.

Mixing 12 ounces of water with approximately 1 tablespoon of salt will yield a salt solution of 5%. Fill a normal spray bottle with this mixture.
This mixture is sufficient to enhance the water's own conductivity. This may cause the circuit to fail more easily when sprayed. Once the mixture is
completed, spray the suspect area liberally with the solution. Then, while monitoring either a scan tool or DMM, manipulate the harness as
discussed previously.

Scan Tool Snapshot Procedure


Snapshot is a recording of what a control module on the vehicle was receiving for information while the snapshot is being made. A snapshot may
be used to analyze the data during the time a vehicle condition is current. This allows you to concentrate on making the condition occur, rather than
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 14
Chevrolet Venture V6-3.4L VIN E 1090
trying to view all the data in anticipation of the fault. The snapshot contains information around a trigger point that you have determined. Only a
single data list may be recorded in each snapshot. The Scan Tool has the ability to store two snapshots. The ability to record two snapshots allows
comparing hot versus cold and good versus bad vehicle scenarios. The snapshots are stored on a 'first in, first out' basis. If a third snapshot is taken,
the first snapshot stored in the memory will be lost.

Snapshots can be one of two types:


- Snapshot - taken from the Snapshot menu choice
- Quick Snapshot - taken from the Data Display soft key choice (Does not contain DTC information)

When a snapshot is taken, it is recorded on the memory card and may contain as many as 1200 frames of information. Because the snapshot is
recorded onto the memory card, snapshots are not lost if the Scan Tool is powered down.

The snapshot replay screen has a plot soft key that can be of great value for intermittent diagnosis. The snapshot plot feature can help you to
quickly determine if a sensor is outside of its expected values by plotting three parameters at a time. The data will be displayed both graphically and
numerically showing the minimum and maximum values for all frames captured. This is helpful, especially if the fault occurs only once and does
not set a DTC.
Testing For A Short to Voltage
NOTE: Refer to Test Probe Notice in Service Precautions.

The following procedure tests for a short to voltage in a circuit.


1. Set the rotary dial of the DMM to the V (DC) position.
2. Connect the positive lead of the DMM to one end of the circuit to be tested.
3. Connect the negative lead of the DMM to a good ground.
4. Turn ON the ignition and operate all accessories.
5. If the voltage measured is greater than 1 volt, there is a short to voltage in the circuit.
Testing For Continuity
NOTE: Refer to Test Probe Notice in Service Precautions.

The following procedures verify good continuity in a circuit.

With a DMM
1. Set the rotary dial of the DMM to the OHM position.
2. Disconnect the power feed (i.e. fuse, control module) from the suspect circuit.
3. Disconnect the load.
4. Press the MIN MAX button on the DMM.
5. Connect one lead of the DMM to one end of the circuit to be tested.
6. Connect the other lead of the DMM to the other end of the circuit.
7. If the DMM displays low or no resistance and a tone is heard, the circuit has good continuity.

With a Test Lamp

IMPORTANT: Only use the test lamp procedure on low impedance power and ground circuits.

1. Remove the power feed (i.e. fuse, control module) from the suspect circuit.
2. Disconnect the load.
3. Connect one lead of the test lamp to one end of the circuit to be tested.
4. Connect the other lead of the test lamp to battery positive voltage.
5. Connect the other end of the circuit to ground.
6. If the test lamp illuminates (full intensity), then the circuit has good continuity.
Testing For Intermittent and Poor Connections
Perform the following procedures while wiggling the harness from side to side. Continue this at convenient points (about 6 inches apart) while
watching the test equipment.
- Testing for Short to Ground
- Testing for Continuity
- Testing for a Short to Voltage

If the fault is not identified, perform the procedure below using the MIN MAX feature on the J 39200 DMM. This feature allows you to manipulate
the circuit without having to watch the J 39200. The J 39200 will generate an audible tone when a change is detected.

IMPORTANT: The J 39200 must be used in order to perform the following procedure since the J 39200 can monitor current, resistance or
voltage while recording the minimum (MIN), and maximum (MAX) values measured.

1. Connect the J 39200 to both sides of a suspected connector (still connected), or from one end of a suspected circuit to the other. Refer to
Troubleshooting with a Digital Multimeter for information on connecting the J 39200 to the circuit.
2. Set the rotary dial of the J 39200 to the V (AC) or V (DC) position.
3. Press the range button of the J 39200 in order to select the desired voltage range.
4. Press the MIN MAX button of the J 39200. The J 39200 displays 100 ms RECORD and emits an audible tone (beep).

IMPORTANT: The 100 ms RECORD mode is the length of time an input must stay at a new value in order to record the full change.
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 15
Chevrolet Venture V6-3.4L VIN E 1091

5. Simulate the condition that is potentially causing the intermittent connection, either by wiggling the connections or the wiring, test driving, or
performing other operations. Refer to Inducing Intermittent Fault Conditions.
6. Listen for the audible Min Max Alert which indicates that a new minimum or maximum value has been recorded.
7. Press the MIN MAX button once in order to display the MAX value and note the value.
8. Press the MIN MAX button again in order to display the MIN value and note the value.
9. Determine the difference between the MIN and MAX values.
- If the variation between the recorded MIN and MAX voltage values is 1 volt or greater an intermittent open or high resistance condition
exists. Repair the condition as necessary.
- If the variation between the recorded MIN and MAX voltage values is less than 1 volt an intermittent open or high resistance condition
does not exist.
Testing For Proper Terminal Contact
It is important to test terminal contact at the component and any in-line connectors before replacing a suspect component. Mating terminals must be
inspected to ensure good terminal contact. A poor connection between the male and female terminal at a connector may be the result of
contamination
or deformation.

Contamination may be caused by the connector halves being improperly connected. A missing or damaged connector seal, damage to the connector
itself, or exposing the terminals to moisture and dirt can also cause contamination. Contamination, usually in the underhood or underbody
connectors, leads to terminal corrosion, causing an open circuit or intermittently open circuit.

Deformation is caused by probing the mating side of a connector terminal without the proper adapter, improperly joining the connector halves, or
repeatedly separating and joining the connector halves. Deformation, usually to the female terminal contact tang, can result in poor terminal contact
causing an open or intermittently open circuit.

Round Wire Connectors


Follow the procedure below to test terminal contact of Metri-Pack or 56 series terminals. Refer to the J 38125-B Terminal Repair kit or the J
38125-4 Instruction Manual for terminal identification.
Follow the procedure below in order to test terminal contact.
1. Separate the connector halves.
2. Visually inspect the connector halves for contamination. Contamination may result in a white or green build-up within the connector body or
between terminals. This causes high terminal resistance, intermittent contact, or an open circuit. An underhood or underbody connector that
shows signs of contamination should be replaced in its entirety: terminals, seals, and connector body.
3. Using an equivalent male terminal from the J 38125-B, test that the retention force is significantly different between a good terminal and a
suspect terminal. Replace the female terminal in question.

Flat Wire (Dock and Lock) Connectors


There are no serviceable parts for flat wire (dock and lock) connectors on the harness side or the component side.
Follow the procedure below in order to test terminal contact.
1. Remove the component in question.
2. Visually inspect each side of the connector for signs of contamination. Avoid touching either side of the connector as oil from your skin may
be a source of contamination as well.
3. Visually inspect the terminal bearing surfaces of the flat wire circuits for splits, cracks, or other imperfections that could cause poor terminal
contact. Visually inspect the component side connector to ensure that all of the terminals are uniform and free of damage or deformation.
4. Insert the appropriate adapter from the J 42675 Flat Wire Probe Adapter Kit on the flat wire harness connector in order to test the circuit in
question.
Testing For Short To Ground
NOTE: Refer to Test Probe Notice in Service Precautions.

The following procedures test for a short to ground in a circuit.

With a DMM
1. Remove the power feed (i.e. fuse, control module) from the suspect circuit.
2. Disconnect the load.
3. Set the rotary dial of the DMM to the OHM position.
4. Connect one lead of the DMM to one end of the circuit to be tested.
5. Connect the other lead of the DMM to a good ground.
6. If the DMM does NOT display infinite resistance (OL), there is a short to ground in the circuit.

With a Test Lamp


1. Remove the power feed (i.e. fuse, control module) from the suspect circuit.
2. Disconnect the load.
3. Connect one lead of the test lamp to battery positive voltage.
4. Connect the other lead of the test lamp to one end of the circuit to be tested.
5. If the test lamp illuminates, there is a short to ground in the circuit.

Fuse Powering Several Loads


1. Review the system schematic and locate the fuse that is open.
2. Open the first connector or switch leading from the fuse to each load.
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 16
Chevrolet Venture V6-3.4L VIN E 1092
3. Connect a DMM across the fuse terminals (be sure that the fuse is powered).
- When the DMM displays voltage the short is in the wiring leading to the first connector or switch.
- If the DMM does not display voltage refer to the next step.
4. Close each connector or switch until the DMM displays voltage in order to find which circuit is shorted.
Troubleshooting With A Digital Multimeter
NOTE: Refer to Test Probe Notice in Service Precautions.

IMPORTANT: Circuits which include any solid state control modules, such as the PCM, should only be tested with a 10 megohm or higher
impedance digital multimeter such as the J 39200.

The J 39200 Instruction Manual is a good source of information and should be read thoroughly upon receipt of the DMM as well as kept on hand
for future reference.

A DMM should be used instead of a test lamp in order to test for voltage in high impedance circuits. While a test lamp shows whether voltage is
present, a DMM indicates how much voltage is present.

The ohmmeter function on a DMM shows how much resistance exists between two points along a circuit. Low resistance in a circuit means good
continuity.

IMPORTANT: Disconnect the power feed from the suspect circuit when measuring resistance with a DMM. This prevents incorrect readings.
DMMs apply such a small voltage to measure resistance that the presence of voltages can upset a resistance reading.

Diodes and solid state components in a circuit can cause a DMM to display a false reading. To find out if a component is affecting a measurement
take a reading once, then reverse the leads and take a second reading. If the readings differ the solid state component is affecting the measurement.

Following are examples of the various methods of connecting the DMM to the
circuit to be tested:
- Backprobe both ends of the connector and either hold the leads in place while manipulating the connector or tape the leads to the harness for
continuous monitoring while you perform other operations or test driving. Refer to Probing Electrical Connectors.
- Disconnect the harness at both ends of the suspected circuit where it connects either to a component or to other harnesses.
- If the system that is being diagnosed has a specified pinout or breakout box, it may be used in order to simplify connecting the DMM to the
circuit or for testing multiple circuits quickly.

Troubleshooting With A Test Lamp


NOTE: Refer to Test Probe Notice in Service Precautions.

A test lamp can simply and quickly test a low impedance circuit for voltage.

The J 34142-B Test Lamp is Micro-Pack compatible and comprised of a 12 voltlight bulb with an attached pair of leads.

To properly operate this tool use the following procedure.


1. Attach one lead to ground.
2. Touch the other lead to various points along the circuit where voltage should be present.
3. When the bulb illuminates, there is voltage at the point being tested.

Flat Wire Repairs


NOTE: The flat wire within the flex wiring harness is not serviceable. If an open or short exists within the flex wiring harness the complete
harness must be replaced.
Heated Oxygen Sensor (HO2S) Wiring Repairs
NOTE: Do not solder repairs under any circumstances as this could result in the air reference being obstructed.

If the heated oxygen sensor pigtail wiring, connector, or terminal is damaged the entire oxygen sensor assembly must be replaced. Do not attempt to
repair the wiring, connector, or terminals. In order for the sensor to function properly it must have a clean air reference. This clean air reference is
obtained by way of the oxygen sensor signal and heater wires. Any attempt to repair the wires, connectors or terminals could result in the
obstruction of the air reference and degrade oxygen sensor performance.

The following guidelines should be used when servicing the heated oxygen sensor:
- Do not apply contact cleaner or other materials to the sensor or vehicle harness connectors. These materials may get into the sensor, causing
poor performance. Also, the sensor pigtail and harness wires must not be damaged in such a way that the wires inside are exposed. This could
provide a path for foreign materials to enter the sensor and cause performance problems.
- Neither the sensor nor vehicle lead wires should be bent sharply or kinked. Sharp bends, kinks, etc., could block the reference air path
through the lead wire.
- Do not remove or defeat the oxygen sensor ground wire (where applicable). Vehicles that utilize the ground wire sensor may rely on this
ground as the only ground contact to the sensor. Removal of the ground wire will also cause poor engine performance.
- To prevent damage due to water intrusion, be sure that the peripheral seal remains intact on the vehicle harness connector.

The engine harness may be repaired using the J 38125-B.


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 17
Chevrolet Venture V6-3.4L VIN E 1093
Repairing Damaged Wire Insulation

Wire Size Conversion Table

IMPORTANT: Fusible links cut longer than 225 mm (approx. 9 inches) will not provide sufficient overload protection.

Refer to Splicing Copper Wire Using Splice Clips.

Repairing Damaged Wire Insulation


If the conductive portion of the wire is not damaged, locate the problem and apply tape around the wire. If the damage is more extensive, replace
the faulty segment of the wire. Refer to Splicing Copper Wire Using Splice Clips and follow the instruction to repair the wire.

SIR/SRS Connector (Plastic Body and Terminal Metal Pin) Repair


Use the connector repair assembly packs in order to repair the damaged SIR/SRS wire harness connectors and the terminals. Do not use the
connector repair assembly pack in order to repair the pigtails. These kits include an instruction sheet and the sealed splices. Use the sealed splices in
order to splice the new wires, connectors, and terminals to the harness. The splice crimping tool is color keyed in order to match the splices from
the J 38125-B. You must use the splice crimping tool in order to apply these splices.

The terminals in the SIR/SRS system are made of a special metal. This metal provides the necessary contact integrity for the sensitive, low energy
circuits. These terminals are only available in the connector repair assembly packs. Do not substitute any other terminals for those in the assembly
packs.

If the individual terminals are damaged on the Sensing And Diagnostic Module (SDM) harness connector, use 1 of the following 2 components in
order to replace the SDM harness connector:
- The SDM harness connector pigtail assembly
- The SDM harness connector replacement kit If the individual terminals are damaged on any other SIR/SRS connection, use the appropriate
connector repair assembly pack in order to replace the entire connection. Replace the entire SIR/SRS wiring harness, if needed, in order to
maintain SIR/SRS circuit integrity
SIR/SRS System Wire Splice Repair
Apply a new splice (not sealed) from the J 38125-B if damage occurs to any of the original equipment splices (3 wires or more) in the SIR/SRS
wiring harness. Carefully follow the instructions included in the kit for proper splice clip application.

SIR/SRS Wire Pigtail Repair


IMPORTANT: Do not make wire, connector, or terminal repairs on components with wire pigtails. A wire pigtail is a wire or wires attached
directly to the device (not by a connector). If a wiring pigtail is damaged, you must replace the entire component (with pigtail). The inflatable
restraint steering wheel module coil is an example of a pigtail component.

SIR/SRS Wire Repair


TOOLS REQUIRED

J 38125-B Terminal Repair Kit

IMPORTANT: Refer to Wiring Repairs in Diagrams in order to determine the correct wire size for the circuit you are repairing. You must
obtain this information in order to ensure circuit integrity.

If any wire except the pigtail is damaged, repair the wire by splicing in a new section of wire of the same gauge size (0.5 mm, 0.8 mm, 1.0 mm
etc.). Use the sealed splices and splice crimping tool from the J 38125-B. Use the following wiring repair procedures in order to ensure the
integrity of the sealed splice.

IMPORTANT: You must perform the following procedures in the listed order. Repeat the procedure if any wire strands are damaged. You
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 18
Chevrolet Venture V6-3.4L VIN E 1094
must obtain a clean strip with all of the wire strands intact.

1. Open the harness by removing any tape:


- Use a sewing seam ripper (available from sewing supply stores) in order to cut open the harness in order to avoid wire insulation damage.
- Use the crimp and sealed splice sleeves on all types of insulation except tefzel and coaxial.
- Do not use the crimp and sealed splice sleeve to form a splice with more than 2 wires coming together.
2. Cut as little wire off the harness as possible. You may need the extra length of wire in order to change the location of a splice.Adjust splice
locations so that each splice is at least 40 mm (1.5 in) away from the other splices, harness branches, or connectors.
3. Strip the insulation:
- When adding a length of wire to the existing harness, use the same size wire as the original wire.
- Perform one of the following items in order to find the correct wire size:
- Find the wire on the schematic and convert the metric size to the equivalent AWG size.
- Use an AWG wire gauge.
- If you are unsure of the wire size, begin with the largest opening in the wire stripper and work down until achieving a clean strip of
the insulation.
- Strip approximately 7.5 mm (0.313 in) of insulation from each wire to be spliced.
- Do not nick or cut any of the strands. Inspect the stripped wire for nicks or cut strands.
- If the wire is damaged, repeat this procedure after removing the damaged section.
4. Select the proper sealed splice sleeve according to the wire size. Refer to the above table at the beginning of the repair procedure for the color
coding of the splice sleeves and the crimp tool nests.

5. Use the Splice Crimp Tool from the J 38125-B in order to position the splice sleeve in the proper color nest of the Splice Crimp Tool.

6. Place the splice sleeve in the nest. Ensure that the crimp falls midway between the end of the barrel and the stop. The sleeve has a stop (3) in
the middle of the barrel (2) in order to prevent the wire (1) from going further. Close the hand crimper handles slightly in order to firmly hold
the splice sleeve in the proper nest.
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 19
Chevrolet Venture V6-3.4L VIN E 1095

7. Insert the wire into the splice sleeve barrel until the wire hits the barrel stop.
8. Tightly close the handles of the crimp tool until the crimper handles open when released. The crimper handles will not open until you apply
the proper amount of pressure to the splice sleeve. Repeat steps 4 and 5 for the opposite end of the splice.

9. Using the heat torch, apply heat to the crimped area of the barrel.
10. Gradually move the heat barrel to the open end of the tubing:
- The tubing will shrink completely as the heat is moved along the insulation.
- A small amount of sealant will come out of the end of the tubing when sufficient shrinkage is achieved.
Splicing Copper Wire Using Splice Clips
TOOLS REQUIRED

J 38125-B Terminal Repair kit

1. Open the harness.


- If the harness is taped, remove the tape.
- To avoid wiring insulation damage, use a sewing ripper in order to cut open the harness.
- If the harness has a black plastic conduit, pull out the desired wire.
2. Cut the wire.
- Cut as little wire off the harness as possible.
- Ensure that each splice is at least 40 mm (1.5 in) away from other splices, harness branches and connectors. This helps prevent moisture
from bridging adjacent splices and causing damage.
3. Select the proper size and type of wire.
- The wire must be of equal or greater size than the original (except fusible link).
- The wire's insulation must have the same or higher temperature rating.
- Use general purpose insulation for areas that are not subject to high temperatures.
- Use a cross-linked polyethylene insulated wire for areas where high temperatures are expected.

IMPORTANT: Use Cross-linked polyethylene wire to replace PVC, but do not replace cross-linked polyethylene with PVC.

Cross-linked polyethylene wire is not fuel resistant. Do not use to replace wire where there is the possibility of fuel contact.

4. Strip the insulation.


- Select the correct size opening in the wire stripper or work down from the largest size.
- Strip approximately 7.5 mm (5/16 in) of insulation from each wire to be spliced.
5. Select the proper clip to secure the splice. Follow the instructions in the J 38125-B Terminal Repair kit in order to determine the proper clip
size crimp tool and anvil.
6. Overlap the two stripped wire ends and hold them between thumb and forefinger.
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 20
Chevrolet Venture V6-3.4L VIN E 1096

7. Center the splice clip (2) over the stripped wires (1) and hold the clip in place.
- Ensure that the wires extend beyond the clip in each direction.
- Ensure that no insulation is caught under the clip.

8. Center the crimp tool over the splice clip and wires.
9. Apply steady pressure until the crimp tool closes. Ensure that no strands of wire are cut.

10. Crimp the splice on each end (2).


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 21
Chevrolet Venture V6-3.4L VIN E 1097

11. Apply 60/40 rosin core solder to the opening in the back of the clip. Follow the manufacturer's instructions for the solder equipment.

12. Tape the splice. Roll on enough tape in order to duplicate the thickness of the insulation on the existing wires.

13. Additional tape can be applied to the wire if the wire does not belong in a conduit or another harness covering. Use a winding motion in order
to cover the first piece of tape.

Splicing Copper Wire Using Splice Sleeves


Use crimp and seal splice sleeves to form a one-to-one splice on all types of insulation except tefzel and coaxial to form a one-to-one splice. Use
tefzel and coaxial where there is special requirements such as moisture sealing. Follow the instructions below in order to splice copper wire using
crimp and seal splice sleeves.

Crimp And Seal Splice Table

Tools Required
J 38125-B Terminal Repair Kit

1. Open the harness.


- If the harness is taped, remove the tape.
- To avoid wiring insulation damage, use a sewing ripper in order to cut open the harness.
- If the harness has a black plastic conduit, pull out the desired wire.
2. Cut the wire.
- Cut as little wire off the harness as possible.
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 22
Chevrolet Venture V6-3.4L VIN E 1098
- Ensure that each splice is at least 40 mm (1.5 in) away from other splices, harness branches and connectors. This helps prevent moisture
from bridging adjacent splices and causing damage.

3. Select the proper size and type of wire.


- The wire must be of equal or greater size than the original.
- The wire's insulation must have the same or higher temperature rating (4).
- Use general purpose insulation for areas that are not subject to high temperatures.
- Use a cross-linked polyethylene insulated wire for areas where high temperatures are expected.

IMPORTANT: Use Cross-linked polyethylene wire to replace PVC, but do not replace cross-linked polyethylene with PVC.

Cross-linked polyethylene wire is not fuel resistant. Do not use to replace wire where there is the possibility of fuel contact.
4. Strip the insulation.
- Select the correct size opening in the wire stripper or work down from the largest size.
- Strip approximately 7.5 mm (5/16 in) of insulation from each wire to be spliced (1).
5. Select the proper splice sleeve (2) and the required crimp nest tool, refer to the Crimp and Seal Splice Table.
6. Place the nest tool in the J 38125 crimp tool.
7. Place the splice sleeve in the crimp tool nest so that the crimp falls at point 1 on the splice.
8. Close the hand crimper handles slightly in order to hold the splice sleeve firmly in the proper crimp tool nest.
9. insert the wires into the splice sleeve until the wire hits the barrel stop. The splice sleeve has a stop in the middle of the barrel in order to
prevent the wire from passing through the splice (3).
10. Close the handles of the J 38125 until the crimper handles open when released. The crimper handles will not open until the proper amount of
pressure is applied to the splice sleeve.
11. Shrink the insulation around the splice.
- Using the heat torch apply heat to the crimped area of the barrel.
- Gradually move the heat barrel to the open end of the tubing.
- The tubing will shrink completely as the heat is moved along the insulation.
- A small amount of sealant will come out of the end of the tubing when sufficient shrinkage is achieved.

Splicing Inline Harness Diodes


Many vehicle electrical Systems use a diode to isolate circuits and protect the components from voltage spikes. When installing a new diode use the
following procedure.
1. Open the harness.
- If the harness is taped, remove the tape.
- To avoid wiring insulation damage, use a sewing ripper in order to cut open the harness.
- If the harness has a black plastic conduit, pull out the diode.
2. If the diode is taped to the harness, remove all of the tape.
3. Check and record the current flow direction and orientation of diode.
4. Remove the inoperative diode from the harness with a suitable soldering tool.

IMPORTANT: If the diode is located next to a connector terminal remove the terminal(s) from the connector to prevent damage from the
soldering tool.

5. Carefully strip away a section of insulation next to the old soldered portion of the wire(s). Do not remove any more than is needed to attach
the new diode.
6. Check current flow direction of the new diode, being sure to install the diode with correct bias. Reference the appropriate service manual
wiring schematic to obtain the correct diode installation position.
7. Attach the new diode to the wire(s) using 60/40 rosin core solder. Before soldering attach some heat sinks (aluminum alligator clips) across
the diode wire ends to protect the diode from excessive heat. Follow the manufacturer's instruction for the soldering equipment.
8. Reinstall terminal(s) into the connector body if previously removed
9. Tape the diode to the harness or connector using electrical tape.

IMPORTANT: To prevent shorts to ground and water intrusion, completely cover all exposed wire and diode attachment points with tape.
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 23
Chevrolet Venture V6-3.4L VIN E 1099
Splicing Twisted or Shielded Cable
Twisted/shielded cable is used in order to protect wiring from electrical noise. Two-conductor cable of this construction is used between the radio
and the Delco-Bose(R) speaker/amplifier units and other applications where low level, sensitive signals must be carried. Follow the instructions
below in order to repair the twisted/shielded cable.

1. Remove the outer jacket (1). Use care not to cut into the drain wire of the mylar tape.
2. Unwrap the tape. Do not remove the tape. Use the tape in order to rewrap the twisted conductors after the splice is made.

3. Prepare the splice. Untwist the conductors and follow the splicing instructions for copper wire. Staggering the splices by 65 mm is
recommended.

4. Re-assemble the cable.


- Rewrap the conductors with the mylar tape.
- Use caution not to wrap the drain wire in the tape (1).
- Follow the splicing instructions for copper wire and splice the drain wire.
- Wrap the drain wire around the conductors and tape with mylar tape.

IMPORTANT: Apply the mylar tape with the aluminum side inward. This ensures good electrical contact with the drain wire.

5. Tape over the entire cable. Use a winding motion when you apply the tape.
Using Connector Test Adapters
NOTE: Do not insert test equipment probes into any connector or fuse block terminal. The diameter of the test probes will deform most terminals.
A deformed terminal can cause a poor connection, which can result in system failures. Always use the J 35616-A Connector Test Adapter Kit or the
J 42675 Flat Wire Probe Adapter Kit in order to frontprobe terminals. Do not use paper clips or other substitutes as they can damage terminals and
cause incorrect measurements.
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 24
Chevrolet Venture V6-3.4L VIN E 1100
Using Fused Jumper Wires
IMPORTANT: A fused jumper may not protect solid state components from being damaged.

The J 36169-A fused jumper includes small clamp connectors that provide adaptation to most connectors without damage. This fused jumper wire
is supplied with a 20 A fuse which may not be suitable for some circuits. Do not use a fuse with a higher rating than the fuse that protects the circuit
being tested.

Wire Size Conversion Table

Push to Seat Connectors


TERMINAL REMOVAL
Follow the steps below in order to repair push to seat connectors.

1. Remove the Terminal Position Assurance (TPA) device, the Connector Position Assurance (CPA) device, and/or the secondary lock.
2. Separate the connector halves (1).

3. Use the proper pick or removal tool (1) in order to release the terminal.
4. Gently pull the cable and the terminal (2) out of the back of the connector.
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 25
Chevrolet Venture V6-3.4L VIN E 1101

5. Re-form the locking device if you are going to reuse the terminal (1).
6. To repair the terminal, refer to Terminal Repair.

TERMINAL REPAIR
1. Slip the cable seal away from the terminal.
2. Cut the wire as close to the terminal as possible.
3. Slip a new cable seal onto the wire.
4. Strip 5 mm (3/16 in) of insulation from the wire
5. Crimp a new terminal to the wire.
6. Solder the crimp with rosin core solder.
7. Slide the cable seal toward the terminal.
8. Crimp the cable seal and the insulation.
9. If the connector is outside of the passenger compartment, apply grease to the connector.

REINSTALLING TERMINAL
1. In order to reuse a terminal or lead assembly. Refer to Wiring Repairs.
2. Ensure that the cable seal is kept on the terminal side of the splice.
3. Insert the lead from the back until it catches.
4. Install the TPA, CPA and/or the secondary locks.
Pull to Seat Connectors
TERMINAL REMOVAL
Follow the steps below in order to repair pull-to-seat connectors.

1. Remove the Terminal Position Assurance (TPA) device, the Connector Position Assurance (CPA) device, and/or the secondary lock.
2. Separate the connector halves.
3. Using the proper pick or removal tool (4) insert into the front of the connector body.
4. Grasp the wire at the back of the connector body and gently pull the terminal (1) from the connector body (3).
5. Inspect the terminal for damage, if damaged refer to Terminal Repair.
6. Reform the locking tang (2) if the terminal is being reused.

TERMINAL REPAIR
1. Slip the cable seal away from the terminal.
2. Cut the wire as close to the terminal as possible.
3. Slip a new cable seal onto the wire.
4. Strip 5 mm (3/16 in) of insulation from the wire.
5. Crimp a new terminal to the wire.
6. Solder the crimp with rosin core solder.
7. Slide the cable seal toward the terminal.
8. Crimp the cable seal and the insulation.
9. If the connector is outside of the passenger compartment, apply grease to the connector.

TERMINAL INSTALLATION
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 26
Chevrolet Venture V6-3.4L VIN E 1102
1. Inspect the terminal for damage. If damaged refer to Terminal Repair.
2. Reform the locking tang (2) if the terminal is being reused.
3. Ensure that the cable seal is kept on the terminal side of the splice.
4. Insert the wire into the back of the connector body. Push until the terminal locking tang locks into the connector body.
5. Install the TPA, CPA and/or the secondary locks.

Terminal Position Assurance (TPA)


The Terminal Position Assurance (TPA) insert resembles the plastic combs used in the control module connectors. The TPA keeps the terminal
securely seated in the connector body. Do not remove the TPA from the connector body unless you remove a terminal for replacement.
Weather Pack Connectors
The following is the proper procedure for the repair of Weather Pack(R) Connectors.

- Separate the connector halves (1).


- Open the secondary lock. A secondary lock aids in terminal retention and is usually molded to the connector (1).
- Grasp the wire and push the terminal to the forward most position. Hold the wire in this position.

- Insert the Weather Pack(R) terminal removal tool into the front (mating end) of the connector cavity until it rests on the cavity shoulder (1).
- Gently pull on the wire to remove the terminal through the back of the connector (2).

IMPORTANT: Never use force to remove a terminal from a connector.

- Inspect the terminal and connector for damage. Repair as necessary. Refer to Repairing Connector Terminals.
- Reform the lock tang (2) and reset terminal in connector body.
- Close secondary locks and join connector halves.
- Verify that circuit is complete and working satisfactorily.
- Perform system check.

Repairing Connector Terminals


Use the following repair procedures in order to repair the following:
- Push to Seat terminals
- Pull to Seat terminals
- Weather Pack(R) terminals

Some terminals do not require all of the steps shown. Skip the steps that do not apply for your immediate terminal repair. The J 38125-B Terminal
Repair kit contains further information.
1. Cut off the terminal between the core and the insulation crimp. Minimize any wire loss. For Weather Pack(R) terminals, remove the seal.
2. Apply the correct seal per gauge size of the wire. For Weather Pack(R) terminals, slide the seal back along the wire in order to enable
insulation removal.
3. Remove the insulation.
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 27
Chevrolet Venture V6-3.4L VIN E 1103
4. For Weather Pack(R) terminals only, align the seal with the end of the cable insulation.
5. Position the strip in the terminal.
For Weather Pack(R) terminals, position the strip and seal in the terminal.
6. Hand crimp the core wings.
7. Hand crimp the insulation wings.
For Weather Pack(R) terminals, hand crimp the insulation wings around the seal and the cable.
8. Solder all of the hand crimp terminals.

Automatic Transmission/Transaxle

Transmission Major Component Locations


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 28
Chevrolet Venture V6-3.4L VIN E 1104

Electronic Component Locations


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 29
Chevrolet Venture V6-3.4L VIN E 1105

Case and Associated Parts (1 of 4)


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 30
Chevrolet Venture V6-3.4L VIN E 1106
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 31
Chevrolet Venture V6-3.4L VIN E 1107

Case and Associated Parts (2 of 4)

Case and Associated Parts (3 of 4)


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 32
Chevrolet Venture V6-3.4L VIN E 1108

Case and Associated Parts (4 of 4)


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 33
Chevrolet Venture V6-3.4L VIN E 1109

Oil Pump Assembly


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 34
Chevrolet Venture V6-3.4L VIN E 1110

Control Valve Body Assembly (1 of 2)


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 35
Chevrolet Venture V6-3.4L VIN E 1111

Control Valve Body Assembly (2 of 2)


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 36
Chevrolet Venture V6-3.4L VIN E 1112
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 37
Chevrolet Venture V6-3.4L VIN E 1113

Case Cover Assembly


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 38
Chevrolet Venture V6-3.4L VIN E 1114
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 39
Chevrolet Venture V6-3.4L VIN E 1115

Internal Components (1 of 2)
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 40
Chevrolet Venture V6-3.4L VIN E 1116
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 41
Chevrolet Venture V6-3.4L VIN E 1117

Internal Components (2 of 2)

Manual Shaft and Parking System Assembly


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 42
Chevrolet Venture V6-3.4L VIN E 1118

Case Side Cover Bolt Locations


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 43
Chevrolet Venture V6-3.4L VIN E 1119

Oil Pump Bolt Locations


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 44
Chevrolet Venture V6-3.4L VIN E 1120

Control Valve Body Bolt Locations


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 45
Chevrolet Venture V6-3.4L VIN E 1121

Case Cover Bolt Locations


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 46
Chevrolet Venture V6-3.4L VIN E 1122

Bottom Pan, Accumulator Cover and Manual 2-1 Band Servo Cover Bolt Locations
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 47
Chevrolet Venture V6-3.4L VIN E 1123

Thrust Washer Locations


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 48
Chevrolet Venture V6-3.4L VIN E 1124

Bushing Locations
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 49
Chevrolet Venture V6-3.4L VIN E 1125

Bearing Locations
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 50
Chevrolet Venture V6-3.4L VIN E 1126

Lip Seal Locations


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 51
Chevrolet Venture V6-3.4L VIN E 1127

Square and O-Ring Seal Locations


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 52
Chevrolet Venture V6-3.4L VIN E 1128

Gasket Locations
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 53
Chevrolet Venture V6-3.4L VIN E 1129

Ball Check Valve Locations


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 54
Chevrolet Venture V6-3.4L VIN E 1130

Oil Pump Cover Fluid Passages (Oil Pump Body Side)


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 55
Chevrolet Venture V6-3.4L VIN E 1131

Oil Pump Body Fluid Passages (Oil Pump Cover Side)


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 56
Chevrolet Venture V6-3.4L VIN E 1132

Oil Pump Body Fluid Passages (Control Valve Body Side)


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 57
Chevrolet Venture V6-3.4L VIN E 1133

Control Valve Body Fluid Passages (Oil Pump Body Side)


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 58
Chevrolet Venture V6-3.4L VIN E 1134

Control Valve Body Fluid Passages (Case Cover Side)


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 59
Chevrolet Venture V6-3.4L VIN E 1135

Control Valve Body to Spacer Plate Gasket Fluid Passages


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 60
Chevrolet Venture V6-3.4L VIN E 1136

Spacer Plate Fluid Passages


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 61
Chevrolet Venture V6-3.4L VIN E 1137

Spacer Plate to Case Cover Gasket Fluid Passages


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 62
Chevrolet Venture V6-3.4L VIN E 1138

Case Cover Fluid Passages (Control Valve Body Side)


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 63
Chevrolet Venture V6-3.4L VIN E 1139

Case Cover Fluid Passages (Case Side)


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 64
Chevrolet Venture V6-3.4L VIN E 1140

Driven Sprocket Support Fluid Passages


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 65
Chevrolet Venture V6-3.4L VIN E 1141

Oil Pump Drive Shaft and Drive Sprocket Support Fluid Passages
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 66
Chevrolet Venture V6-3.4L VIN E 1142

Case Fluid Passages (Case Cover Side)


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 67
Chevrolet Venture V6-3.4L VIN E 1143

Case Fluid Passages (Bottom)


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 68
Chevrolet Venture V6-3.4L VIN E 1144

1-2 and 2-3 Accumulator Housing Fluid Passages


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 69
Chevrolet Venture V6-3.4L VIN E 1145

Accumulator Cover Spacer Plate Fluid Passages


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 70
Chevrolet Venture V6-3.4L VIN E 1146

Accumulator Cover Fluid Passages


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 71
Chevrolet Venture V6-3.4L VIN E 1147

Manual 2-1 Band Servo Cover Fluid Passages


Axle Shaft Assembly
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 72
Chevrolet Venture V6-3.4L VIN E 1148

Tripot Design-Halfshaft

Engine
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 73
Chevrolet Venture V6-3.4L VIN E 1149

Upper Intake Manifold and Components


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 74
Chevrolet Venture V6-3.4L VIN E 1150

Lower Intake Manifold, Cylinder Head, and Components


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 75
Chevrolet Venture V6-3.4L VIN E 1151

Engine Block and Components


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 76
Chevrolet Venture V6-3.4L VIN E 1152

Crankshaft and Components


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 77
Chevrolet Venture V6-3.4L VIN E 1153

Steering Column
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 78
Chevrolet Venture V6-3.4L VIN E 1154
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 79
Chevrolet Venture V6-3.4L VIN E 1155

Steering Gear
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 80
Chevrolet Venture V6-3.4L VIN E 1156
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 81
Chevrolet Venture V6-3.4L VIN E 1157

In-line Connector C101 (Part 1 Of 2)


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 82
Chevrolet Venture V6-3.4L VIN E 1158

In-line Connector C101 (Part 2 Of 2)


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 83
Chevrolet Venture V6-3.4L VIN E 1159

In-line Connector C102


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 84
Chevrolet Venture V6-3.4L VIN E 1160

In-line Connector C105


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 85
Chevrolet Venture V6-3.4L VIN E 1161

In-line Connector C111


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 86
Chevrolet Venture V6-3.4L VIN E 1162
In-line Connector C120

In-line Connector C171

In-line Connector C172


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 87
Chevrolet Venture V6-3.4L VIN E 1163

In-line Connector C200 (Part 1 Of 2)


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 88
Chevrolet Venture V6-3.4L VIN E 1164

In-line Connector C200 (Part 2 Of 2)


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 89
Chevrolet Venture V6-3.4L VIN E 1165

In-line Connector C201


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 90
Chevrolet Venture V6-3.4L VIN E 1166

In-line Connector C201


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 91
Chevrolet Venture V6-3.4L VIN E 1167

In-line Connector C201


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 92
Chevrolet Venture V6-3.4L VIN E 1168

In-line Connector C203 (Part 1 Of 3)


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 93
Chevrolet Venture V6-3.4L VIN E 1169

In-line Connector C203 (Part 2 Of 3)


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 94
Chevrolet Venture V6-3.4L VIN E 1170

In-line Connector C203 (Part 3 Of 3)

In-line Connector C205


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 95
Chevrolet Venture V6-3.4L VIN E 1171

In-line Connector C215

In-line Connector C216


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 96
Chevrolet Venture V6-3.4L VIN E 1172

In-line Connector C301


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 97
Chevrolet Venture V6-3.4L VIN E 1173

In-line Connector C302


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 98
Chevrolet Venture V6-3.4L VIN E 1174

In-line Connector C303


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 99
Chevrolet Venture V6-3.4L VIN E 1175

In-line Connector C304

In-line Connector C305


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 100
Chevrolet Venture V6-3.4L VIN E 1176

In-line Connector C305

In-line Connector C306


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 101
Chevrolet Venture V6-3.4L VIN E 1177

In-line Connector C308


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 102
Chevrolet Venture V6-3.4L VIN E 1178

In-line Connector C309

In-line Connector C313/C314


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 103
Chevrolet Venture V6-3.4L VIN E 1179

In-line Connector C315

In-line Connector C316


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 104
Chevrolet Venture V6-3.4L VIN E 1180

In-line Connector C400

In-line Connector C401


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 105
Chevrolet Venture V6-3.4L VIN E 1181

In-line Connector C402

In-line Connector C403


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 106
Chevrolet Venture V6-3.4L VIN E 1182

In-line Connector C405

In-line Connector C407 (Domestic)


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 107
Chevrolet Venture V6-3.4L VIN E 1183

In-line Connector C407 (Export)

Inflatable Restraint Front Side Impact Module (RH)


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 108
Chevrolet Venture V6-3.4L VIN E 1184

Inflatable Restraint Front Side Impact Module (LH)

Inflatable Restraint IP Module


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 109
Chevrolet Venture V6-3.4L VIN E 1185

Inflatable Restraint Sensing And Diagnostic Module (SDM)


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 110
Chevrolet Venture V6-3.4L VIN E 1186

Auxiliary Temperature Valve Actuator

Electric Air Inlet Actuator


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 111
Chevrolet Venture V6-3.4L VIN E 1187

Electric Slave Actuator

Mass Air Flow (MAF) Sensor


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 112
Chevrolet Venture V6-3.4L VIN E 1188

Secondary Air Injection Pump

Air Relay
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 113
Chevrolet Venture V6-3.4L VIN E 1189

Theft Deterrent Pass III Key Module

Generator
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 114
Chevrolet Venture V6-3.4L VIN E 1190

Daytime Running Lamps (DRL) Ambient Light Sensor

Ambient Air Temperature Sensor


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 115
Chevrolet Venture V6-3.4L VIN E 1191
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 116
Chevrolet Venture V6-3.4L VIN E 1192
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 117
Chevrolet Venture V6-3.4L VIN E 1193
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 118
Chevrolet Venture V6-3.4L VIN E 1194

Automatic Transaxle (C111)


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 119
Chevrolet Venture V6-3.4L VIN E 1195
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 120
Chevrolet Venture V6-3.4L VIN E 1196
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 121
Chevrolet Venture V6-3.4L VIN E 1197

Transaxle Range Switch C1


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 122
Chevrolet Venture V6-3.4L VIN E 1198

Transaxle Range Switch C2


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 123
Chevrolet Venture V6-3.4L VIN E 1199

Backup Lamp Relay


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 124
Chevrolet Venture V6-3.4L VIN E 1200

Auxiliary Blower Motor

Auxiliary Blower Motor Resistor


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 125
Chevrolet Venture V6-3.4L VIN E 1201

Blower Motor Resistor

Auxiliary Heater - A/C Control Connector C2 (Auxiliary Blower Switch)


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 126
Chevrolet Venture V6-3.4L VIN E 1202

Heater - A/C Control Connector C1 (Blower Motor Switch)

Rear Window Wiper/Washer And Multi-function Switch Connector C2 (Auxiliary Blower Switch)
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 127
Chevrolet Venture V6-3.4L VIN E 1203

Body Control Module (BCM) C1


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 128
Chevrolet Venture V6-3.4L VIN E 1204

Body Control Module (BCM) C2 (Part 1 Of 2)


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 129
Chevrolet Venture V6-3.4L VIN E 1205

Body Control Module (BCM) C2 (Part 2 Of 2)


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 130
Chevrolet Venture V6-3.4L VIN E 1206

Stop Lamp Switch C1


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 131
Chevrolet Venture V6-3.4L VIN E 1207
Stop Lamp Switch C1

Camshaft Position (CKP) Sensor

Camshaft Position (CKP) Sensor (24X)


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 132
Chevrolet Venture V6-3.4L VIN E 1208

Evaporation Emission (EVAP) Canister Purge Solenoid Valve

Evaporation Emission (EVAP) Canister Vent Solenoid Valve


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 133
Chevrolet Venture V6-3.4L VIN E 1209

Cargo Lamp

Center High Mounted Stop Lamp (CHMSL)


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 134
Chevrolet Venture V6-3.4L VIN E 1210

Inflatable Restraint Steering Wheel Module Coil

Remote CD Changer
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 135
Chevrolet Venture V6-3.4L VIN E 1211

A/C Compressor Clutch Coil

Auxiliary Heater - A/C Control Connector C1 (Temperature Control)


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 136
Chevrolet Venture V6-3.4L VIN E 1212

Auxiliary Heater - A/C Control Connector C2 (Auxiliary Blower Switch)

Heater - A/C Control Connector C2 (Compressor And Air Delivery Control)


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 137
Chevrolet Venture V6-3.4L VIN E 1213

Heater - A/C Control Connector C1 (Blower Motor Switch)

Rear Window Wiper/Washer And Multi-function Switch Connector C2 (Auxiliary Blower Switch)
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 138
Chevrolet Venture V6-3.4L VIN E 1214

Engine Coolent Temp (ECT) Sensor

LH IP Courtesy Lamp
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 139
Chevrolet Venture V6-3.4L VIN E 1215

RH IP Courtesy Lamp

Ashtray Lamp Connector


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 140
Chevrolet Venture V6-3.4L VIN E 1216

IP Compartment Lamp Switch

Interior Lamp And Multi-function Switch C1


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 141
Chevrolet Venture V6-3.4L VIN E 1217

Interior Lamp and Multi-function Switch Connector C3 (Power Sliding Door

Interior Lamp and Multi-function Switch Connector C4 (Rear Quarter Window Switch)
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 142
Chevrolet Venture V6-3.4L VIN E 1218

Crankshaft Position (CKP) Sensor (7X)

Cruise Control Module


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 143
Chevrolet Venture V6-3.4L VIN E 1219

Cruise Control Release Switch

Data Link Connector (DLC)


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 144
Chevrolet Venture V6-3.4L VIN E 1220

Daytime Running Lamps (DRL) Ambient Light Sensor

Daytime Running Lamps (DRL) - Control Module C1


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 145
Chevrolet Venture V6-3.4L VIN E 1221

Daytime Running Lamps (DRL) - Control Module C2


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 146
Chevrolet Venture V6-3.4L VIN E 1222

Headlamp And I/P Lamp Dimmer Switch

Dome Lamp
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 147
Chevrolet Venture V6-3.4L VIN E 1223

Front Door Lock Cylinder Switch

Connector C1 - Rear Side Door Actuator Control Module


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 148
Chevrolet Venture V6-3.4L VIN E 1224

Connector C2 - Rear Side Door Actuator Control Module

Connector C3 - Rear Side Door Actuator Control Module


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 149
Chevrolet Venture V6-3.4L VIN E 1225

Connector C4 - Rear Side Door Actuator Control Module

Rear Side Door Actuator Control Module C5


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 150
Chevrolet Venture V6-3.4L VIN E 1226

Exhaust Gas Recirculation (EGR) Valve

Electronic Brake Control Module


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 151
Chevrolet Venture V6-3.4L VIN E 1227
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 152
Chevrolet Venture V6-3.4L VIN E 1228
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 153
Chevrolet Venture V6-3.4L VIN E 1229

Powertrain Control Module (PCM) Connector C1 (Part 1 Of 2)


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 154
Chevrolet Venture V6-3.4L VIN E 1230

Powertrain Control Module (PCM) Connector C1 (Part 2 Of 2)


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 155
Chevrolet Venture V6-3.4L VIN E 1231

Powertrain Control Module (PCM) Connector C2 (Part 1 Of 2)


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 156
Chevrolet Venture V6-3.4L VIN E 1232

Powertrain Control Module (PCM) Connector C2 (Part 2 Of 2)


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 157
Chevrolet Venture V6-3.4L VIN E 1233

LF Fog Lamp

RF Fog Lamp

Fuel Injector 1
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 158
Chevrolet Venture V6-3.4L VIN E 1234

Fuel Injector 2

Fuel Injector 3
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 159
Chevrolet Venture V6-3.4L VIN E 1235

Fuel Injector 4

Fuel Injector 5
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 160
Chevrolet Venture V6-3.4L VIN E 1236
Fuel Injector 6

Fuel Pump Sender Unit C1

Fuel Tank Pressure Sensor C2


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 161
Chevrolet Venture V6-3.4L VIN E 1237

Relay Center(Domestic)
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 162
Chevrolet Venture V6-3.4L VIN E 1238

Relay Center(Export)
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 163
Chevrolet Venture V6-3.4L VIN E 1239

Splice Pack SP205


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 164
Chevrolet Venture V6-3.4L VIN E 1240

Underhood Accessory Wiring Junction Block C1 (Part 1 Of 2)


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 165
Chevrolet Venture V6-3.4L VIN E 1241

Underhood Accessory Wiring Junction Block C1 (Part 2 Of 2)


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 166
Chevrolet Venture V6-3.4L VIN E 1242

Underhood Accessory Wiring Junction Block C2 (Part 1 Of 2)


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 167
Chevrolet Venture V6-3.4L VIN E 1243

Underhood Accessory Wiring Junction Block C2 (Part 2 Of 2)


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 168
Chevrolet Venture V6-3.4L VIN E 1244

Underhood Accessory Wiring Junction Block C3 (Part 1 Of 2)


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 169
Chevrolet Venture V6-3.4L VIN E 1245

Underhood Accessory Wiring Junction Block C3 (Part 2 Of 2)

Underhood Accessory Wiring Junction Block C4


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 170
Chevrolet Venture V6-3.4L VIN E 1246

Underhood Accessory Wiring Junction Block C5

Underhood Accessory Wiring Junction Block C6


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 171
Chevrolet Venture V6-3.4L VIN E 1247

Hazard Lamp/Turn Signal Flasher

LH Headlamp
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 172
Chevrolet Venture V6-3.4L VIN E 1248

RH Headlamp

Headlamp And I/P Lamp Dimmer Switch


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 173
Chevrolet Venture V6-3.4L VIN E 1249

Rear Window Defogger Grid (C1)

Rear Window Defogger Grid (C2)

LH Horn
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 174
Chevrolet Venture V6-3.4L VIN E 1250

RH Horn

Idle Air Control (IAC) Valve


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 175
Chevrolet Venture V6-3.4L VIN E 1251

Ignition Control Module (ICM) C1

Ignition Control Module (ICM) C2


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 176
Chevrolet Venture V6-3.4L VIN E 1252

Inflatable Restraint Side Impact Sensor (SIS) (LH)

Inflatable Restraint Side Impact Sensor (SIS) (RH)

Cigar Lighter Connector


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 177
Chevrolet Venture V6-3.4L VIN E 1253

Sliding Door Jamb Switch


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 178
Chevrolet Venture V6-3.4L VIN E 1254

Driver Information Display


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 179
Chevrolet Venture V6-3.4L VIN E 1255

Instrument Cluster Connector C1


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 180
Chevrolet Venture V6-3.4L VIN E 1256

Instrument Cluster Connector C2

Intake Air Temperature (IAT) Sensor


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 181
Chevrolet Venture V6-3.4L VIN E 1257

Remote Control Door Lock Receiver (RCDLR)

LH License Lamp
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 182
Chevrolet Venture V6-3.4L VIN E 1258

RH License Lamp

Manifold Air Pressure (MAP) Sensor


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 183
Chevrolet Venture V6-3.4L VIN E 1259

Windshield Header Courtesy/Reading Lamps

LH Roof Rail Reading Lamp


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 184
Chevrolet Venture V6-3.4L VIN E 1260

RH Roof Rail Reading Lamp

RR Roof Rail Reading Lamp


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 185
Chevrolet Venture V6-3.4L VIN E 1261

LF Side Marker

RF Side Marker
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 186
Chevrolet Venture V6-3.4L VIN E 1262

Outside Rearview Mirror (Mirror Motor Pack and Heated Defogger)


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 187
Chevrolet Venture V6-3.4L VIN E 1263

Outside Rearview Mirror Remote Control Switch

Engine Oil Level Indicator Switch


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 188
Chevrolet Venture V6-3.4L VIN E 1264

Engine Oil Pressure Indicator Switch

Heated Oxygen Sensor 1 (HO2S 1)


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 189
Chevrolet Venture V6-3.4L VIN E 1265

Heated Oxygen Sensor 2 (HO2S 2)


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 190
Chevrolet Venture V6-3.4L VIN E 1266

LF Park/Turn Lamp

RF Park/Turn Lamp
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 191
Chevrolet Venture V6-3.4L VIN E 1267

Front Door Lock Connector C1 (Ajar Indicator Switch)

Front Door Lock Connector C2 (Actuator)


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 192
Chevrolet Venture V6-3.4L VIN E 1268

Rear Door Lock (Actuator)

Door Lock Switch Plate (Door Mounted, Plunger)


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 193
Chevrolet Venture V6-3.4L VIN E 1269

LH Door Lock Switch Plate (Pillar Mounted, Striker)

RH Door Lock Switch Plate (Pillar Mounted, Striker)


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 194
Chevrolet Venture V6-3.4L VIN E 1270

Front Door Lock Switch


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 195
Chevrolet Venture V6-3.4L VIN E 1271

Radio Rear Seat Audio Control


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 196
Chevrolet Venture V6-3.4L VIN E 1272

Radio Rear Seat Audio Control (With Video Entertainment)


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 197
Chevrolet Venture V6-3.4L VIN E 1273

Second Seat Audio (SSA) Control


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 198
Chevrolet Venture V6-3.4L VIN E 1274

Third Seat Audio (TSA) Control

LH Radio Speaker
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 199
Chevrolet Venture V6-3.4L VIN E 1275

LH Radio Liftgate Speaker


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 200
Chevrolet Venture V6-3.4L VIN E 1276

Radio C1
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 201
Chevrolet Venture V6-3.4L VIN E 1277

RH Radio Liftgate Speaker

RH Radio Speaker
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 202
Chevrolet Venture V6-3.4L VIN E 1278

A/C Refrigerant Pressure Sensor

Seat Belt Switch


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 203
Chevrolet Venture V6-3.4L VIN E 1279

Driver Seat Belt Switch

Driver Seat Belt Pretensioner

Passenger Seat Belt Pretensioner


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 204
Chevrolet Venture V6-3.4L VIN E 1280

Power Seat Systems Connector End Views

C314
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 205
Chevrolet Venture V6-3.4L VIN E 1281

Driver/Passenger Seat Adjuster Motor Assembly

Driver Seat Adjuster Switch


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 206
Chevrolet Venture V6-3.4L VIN E 1282

Driver Seat Heater Module (Passenger similar)

Passenger Seat Adjuster Switch


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 207
Chevrolet Venture V6-3.4L VIN E 1283

Passenger Seat Heater Harness


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 208
Chevrolet Venture V6-3.4L VIN E 1284

Heated Seat Switch

Theft Deterrent Shock Sensor


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 209
Chevrolet Venture V6-3.4L VIN E 1285

Power Sliding Door Detent Switch

Power Sliding Door Open/Close Switch (RH B-Pillar)


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 210
Chevrolet Venture V6-3.4L VIN E 1286

Power Sliding Door Unlatch Actuator

LH Sunshade Lighted Vanity Mirror


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 211
Chevrolet Venture V6-3.4L VIN E 1287

RH Sunshade Lighted Vanity Mirror

LH Taillamp
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 212
Chevrolet Venture V6-3.4L VIN E 1288

RH Taillamp

Tape Retract Module (TRM)


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 213
Chevrolet Venture V6-3.4L VIN E 1289

Throttle Position (TP) Sensor

Liftgate Door Lock Connector C1 (Ajar Indicator Switch)


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 214
Chevrolet Venture V6-3.4L VIN E 1290

Liftgate Door Lock Cylinder Switch

Liftgate Door Lock Connector C2 (Actuator)


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 215
Chevrolet Venture V6-3.4L VIN E 1291

Hazard Lamp/Turn Signal Flasher

LF Park/Turn Lamp
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 216
Chevrolet Venture V6-3.4L VIN E 1292

RF Park/Turn Lamp

Air Injector BL Valve


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 217
Chevrolet Venture V6-3.4L VIN E 1293

Vehicle Speed Sensor (VSS)


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 218
Chevrolet Venture V6-3.4L VIN E 1294
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 219
Chevrolet Venture V6-3.4L VIN E 1295

Rear Quarter Window Actuator

Front Window Regulator Motor


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 220
Chevrolet Venture V6-3.4L VIN E 1296

LF Window Switch

RF Window Switch
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 221
Chevrolet Venture V6-3.4L VIN E 1297

Windshield Washer Pump

Rear Window Washer Pump


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 222
Chevrolet Venture V6-3.4L VIN E 1298

Windshield Wiper/Washer Switch

Rear Window Wiper Motor


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 223
Chevrolet Venture V6-3.4L VIN E 1299

Windshield Wiper Motor

Rear Window Wiper/Washer And Multi-Function Switch


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 224
Chevrolet Venture V6-3.4L VIN E 1300

Rear Window Wiper/Washer And Multi-function Switch C3

Cell References
CELL REFERENCES

General Motors vehicles often use "CELL" references in their electrical wiring diagrams. These references are used in the Original Equipment
Manual to refer to a section in the manual and not a specific diagram(s).

GM Sample Diagram W/ Cell Reference

For instance, in the diagram illustrated "Cell 20" is not a reference to another diagram but a reference to "Section 20" in the OE manual. In the
example, "Section 20" is the engine control section of the manual.
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 225
Chevrolet Venture V6-3.4L VIN E 1301

To navigate through these "Cell" references start at the vehicle level and go to: Diagrams / Electrical Diagrams - for a complete list of the
diagrams available for the vehicle. Choose the system you are working on and view those diagrams.

Note: If unsure of the system - try utilizing the search feature. Type a component in the search feature that belongs to the system and when
the results are displayed note the path displayed. This will show the system the component belongs in.

Retained Accessory Power (RAP) Schematics


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 226
Chevrolet Venture V6-3.4L VIN E 1302

SIR Schematics: Power, Ground, DLC, And SIR Lamp


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 227
Chevrolet Venture V6-3.4L VIN E 1303

SIR Schematics: Sensors, Practitioners, And Side Air Bags


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 228
Chevrolet Venture V6-3.4L VIN E 1304

Radio/Audio System Schematics: Windshield Antenna


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 229
Chevrolet Venture V6-3.4L VIN E 1305

ABS Schematics (ABS/TCS Schematics): ABS Module, Relay, Modulator, Power


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 230
Chevrolet Venture V6-3.4L VIN E 1306

ABS Schematics (ABS/TCS Schematics): ABS Module, Ground, Instrument Cluster, PCM, Power, TCS
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 231
Chevrolet Venture V6-3.4L VIN E 1307

ABS Schematics (ABS/TCS Schematics): ABS Module, DLC Ground, Instrument Cluster, PCM, Power, Stop Lamp Switch
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 232
Chevrolet Venture V6-3.4L VIN E 1308

ABS Schematics (ABS/TCS Schematics): ABS Module, Wheel Speed Sensors


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 233
Chevrolet Venture V6-3.4L VIN E 1309

ABS Schematics (ABS/TCS Schematics): ABS Module, Ground, Instrument Cluster, PCM, Power, TCS
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 234
Chevrolet Venture V6-3.4L VIN E 1310

Theft Deterrent System Schematics: G200, G302


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 235
Chevrolet Venture V6-3.4L VIN E 1311

Theft Deterrent System Schematics (Pass Key III Module)

System Diagram
For information regarding Diagrams for this system, please refer to Transmission Control Systems diagrams. See: Powertrain
Management/Transmission Control Systems/Diagrams/Electrical Diagrams
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 236
Chevrolet Venture V6-3.4L VIN E 1312

Schematic
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 237
Chevrolet Venture V6-3.4L VIN E 1313

Engine Controls Schematics: Automatic Transaxle (Part 1 Of 2)


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 238
Chevrolet Venture V6-3.4L VIN E 1314

Schematic
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 239
Chevrolet Venture V6-3.4L VIN E 1315

Engine Controls Schematics: Automatic Transaxle (Part 1 Of 2)


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 240
Chevrolet Venture V6-3.4L VIN E 1316

Schematic
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 241
Chevrolet Venture V6-3.4L VIN E 1317

Schematic
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 242
Chevrolet Venture V6-3.4L VIN E 1318

Engine Controls Schematics: Automatic Transaxle (Part 2 Of 2)


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 243
Chevrolet Venture V6-3.4L VIN E 1319

Schematic

Schematic
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 244
Chevrolet Venture V6-3.4L VIN E 1320

Engine Controls Schematics: Automatic Transaxle (Part 2 Of 2)


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 245
Chevrolet Venture V6-3.4L VIN E 1321

Engine Controls Schematics: Transaxle Range Switch


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 246
Chevrolet Venture V6-3.4L VIN E 1322

Engine Controls Schematics: Automatic Transaxle (Part 1 Of 2)


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 247
Chevrolet Venture V6-3.4L VIN E 1323

Engine Controls Schematics: Automatic Transaxle (Part 2 Of 2)


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 248
Chevrolet Venture V6-3.4L VIN E 1324

Brake Warning System Schematics


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 249
Chevrolet Venture V6-3.4L VIN E 1325

Cruise Control Schematics

Cruise Control Module


For further information regarding this component please refer to Cruise Control System Information. See See: Cruise
Control/Diagrams/Electrical Diagrams
Cruise Control Switch
For further information regarding this component please refer to Cruise Control System Information. See See: Cruise
Control/Diagrams/Electrical Diagrams
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 250
Chevrolet Venture V6-3.4L VIN E 1326

Defogger Schematics
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 251
Chevrolet Venture V6-3.4L VIN E 1327

Schematic
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 252
Chevrolet Venture V6-3.4L VIN E 1328

Engine Controls Schematics: Engine Data Sensors, A/C Refrig Press, TP, MAP, ECT, IAT
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 253
Chevrolet Venture V6-3.4L VIN E 1329

HVAC Air Delivery/Temperature Control Schematics: Front Air Delivery


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 254
Chevrolet Venture V6-3.4L VIN E 1330
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 255
Chevrolet Venture V6-3.4L VIN E 1331

HVAC Air Delivery/Temperature Control Schematics: Front Air Delivery


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 256
Chevrolet Venture V6-3.4L VIN E 1332

HVAC Blower Control Schematics: Front Blower Controls


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 257
Chevrolet Venture V6-3.4L VIN E 1333

HVAC Air Delivery/Temperature Control Schematics: Rear Air Delivery


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 258
Chevrolet Venture V6-3.4L VIN E 1334

HVAC Blower Control Schematics: Rear Blower Controls


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 259
Chevrolet Venture V6-3.4L VIN E 1335

HVAC Air Delivery/Temperature Control Schematics: Vacuums

Auxiliary Blower Motor


For further information regarding this component and the system that it is a part of please refer to Diagrams See: Heating and Air
Conditioning/Diagrams/Electrical Diagrams

Compressor HVAC
For further information regarding this component and the system that it is a part of please refer to Diagrams See: Heating and Air
Conditioning/Diagrams/Electrical Diagrams
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 260
Chevrolet Venture V6-3.4L VIN E 1336

Audible Warnings Schematics


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 261
Chevrolet Venture V6-3.4L VIN E 1337

Brake Warning System Schematics


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 262
Chevrolet Venture V6-3.4L VIN E 1338

Driver Information System Schematics


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 263
Chevrolet Venture V6-3.4L VIN E 1339

Instrument Cluster: Analog Schematics (Power, Ground Class 2 Data Line, Gauges)
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 264
Chevrolet Venture V6-3.4L VIN E 1340

Instrument Cluster: Analog Schematics (Hardwire Indicators)


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 265
Chevrolet Venture V6-3.4L VIN E 1341

Instrument Cluster: Analog Schematics (Class 2 Telltales)


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 266
Chevrolet Venture V6-3.4L VIN E 1342

Cigar Lighter/Auxiliary Outlets Schematics


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 267
Chevrolet Venture V6-3.4L VIN E 1343

Schematic
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 268
Chevrolet Venture V6-3.4L VIN E 1344

Engine Controls Schematics: Power, Ground, MIL, DLC


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 269
Chevrolet Venture V6-3.4L VIN E 1345

Schematic
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 270
Chevrolet Venture V6-3.4L VIN E 1346

Exterior Lights Schematics (Domestic): DRL Ambient Light Sensor, DRL Control Module
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 271
Chevrolet Venture V6-3.4L VIN E 1347

Fog Lights Schematics (Front Foglights)


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 272
Chevrolet Venture V6-3.4L VIN E 1348

Fog Lights Schematics (Rear Foglights - Export) (Fog Lights Schematics (Rear Fog Lights-Export 1 Of 2))
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 273
Chevrolet Venture V6-3.4L VIN E 1349

Fog Lights Schematics (Rear Foglights - Export) (Fog Lights Schematics (Rear Fog Lights-Export 2 Of 2))
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 274
Chevrolet Venture V6-3.4L VIN E 1350

Backup Lights Schematics


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 275
Chevrolet Venture V6-3.4L VIN E 1351

Exterior Lights Schematics (Domestic): Fuse Block And G401


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 276
Chevrolet Venture V6-3.4L VIN E 1352

Exterior Lights Schematics (Domestic) (Hazard Lamp/Turn Signal Flasher, Turn Signal Switch)
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 277
Chevrolet Venture V6-3.4L VIN E 1353

Headlights Schematics (Domestic): Park Brake Indicator Switch, DRL Ambient Light Sensor
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 278
Chevrolet Venture V6-3.4L VIN E 1354

Headlights Schematics (Domestic): Headlamp And IP Lamp Dimmer Switch


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 279
Chevrolet Venture V6-3.4L VIN E 1355

Headlights Schematics (Domestic ): Headlamps


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 280
Chevrolet Venture V6-3.4L VIN E 1356

Headlights Schematics (Export ) (Headlights Schematics (Headlights-Export))


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 281
Chevrolet Venture V6-3.4L VIN E 1357

Headlights Schematics (Export W/DRL) (Headlights Schematics (Daytime Running Lights-Export 1 Of 3))
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 282
Chevrolet Venture V6-3.4L VIN E 1358

Headlights Schematics (Export W/DRL) (Headlights Schematics (Daytime Running Lights-Export 2 Of 3))
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 283
Chevrolet Venture V6-3.4L VIN E 1359

Headlights Schematics (Export W/DRL) (Headlights Schematics (Daytime Running Lights-Export 3 Of 3))
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 284
Chevrolet Venture V6-3.4L VIN E 1360

Exterior Lights Schematics (Domestic): License Lamps, Relay Center


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 285
Chevrolet Venture V6-3.4L VIN E 1361

Exterior Lights Schematics (Domestic): Stoplamp Switch, Center High Mounted Stop Lamp
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 286
Chevrolet Venture V6-3.4L VIN E 1362

Exterior Lights Schematics (Domestic): Taillamps, Side Markers, Park/Turn Lamps


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 287
Chevrolet Venture V6-3.4L VIN E 1363

Exterior Lights Schematics (Export): Hazard Lamp/Turn Signal Flasher, Turn Signal Switch-Export
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 288
Chevrolet Venture V6-3.4L VIN E 1364

Exterior Lights Schematics (Export) (Export Headlamp Position Lamps/License Lamps)


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 289
Chevrolet Venture V6-3.4L VIN E 1365
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 290
Chevrolet Venture V6-3.4L VIN E 1366

Exterior Lights Schematics (Export) (Export Stoplamps And CHMSL)


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 291
Chevrolet Venture V6-3.4L VIN E 1367

Exterior Lights Schematics (Export) (Export Taillamps)


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 292
Chevrolet Venture V6-3.4L VIN E 1368

Exterior Lights Schematics (Export) (Export Turn And Side Marker Lamps)
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 293
Chevrolet Venture V6-3.4L VIN E 1369

Exterior Lights Schematics (Export) (Export Trailer Wiring Harness)


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 294
Chevrolet Venture V6-3.4L VIN E 1370

Interior Lights Dimming Schematics: Headlamp And IP Lamp Dimmer Switch, Driver Information Display
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 295
Chevrolet Venture V6-3.4L VIN E 1371

Interior Lights Dimming Schematics: Heater-A/C Control Switches And Instrument Cluster
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 296
Chevrolet Venture V6-3.4L VIN E 1372

Interior Lights Dimming Schematics: Interior Lamp And Multifunction Switch, Right Rear Door Latch, Release Actuator Switch
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 297
Chevrolet Venture V6-3.4L VIN E 1373

Interior Lights Dimming Schematics: Rear Window Wiper/Washer And Multifunction Switch, Window Switches, Door Lock Switches
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 298
Chevrolet Venture V6-3.4L VIN E 1374

Interior Lights Schematics: Door Locks, Sliding Door Jamb Switches, Liftgate Door Lock
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 299
Chevrolet Venture V6-3.4L VIN E 1375

Interior Lights Schematics: Headlamp And IP Lamp Dimmer Switch


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 300
Chevrolet Venture V6-3.4L VIN E 1376

Interior Lights Schematics: Interior Lamp And Multifunction Switch, Sunshade Lighted Vanity Mirror
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 301
Chevrolet Venture V6-3.4L VIN E 1377

Interior Lights Schematics: Underhood Lamp, Windshield Header/Courtesy Reading Lamps

Ambient Light Sensor


For further information regarding this component please refer to Lighting and Horns System Information. See See: Lighting and
Horns/Diagrams/Electrical Diagrams
System Diagram
For further information regarding this component please refer to Lighting and Horns System Information. See See: Lighting and
Horns/Diagrams/Electrical Diagrams
Backup Lamp Relay
For further information regarding this component please refer to Lighting and Horns System Information. See See: Lighting and
Horns/Diagrams/Electrical Diagrams
Backup Lamp Switch
For further information regarding this component please refer to Lighting and Horns System Information. See See: Lighting and
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 302
Chevrolet Venture V6-3.4L VIN E 1378
Horns/Diagrams/Electrical Diagrams
Brake Lamp
For further information regarding this component please refer to Lighting and Horns System Information. See See: Lighting and
Horns/Diagrams/Electrical Diagrams
Reference to System Information
For further information regarding this component please refer to Lighting and Horns System Information. See See: Lighting and
Horns/Diagrams/Electrical Diagrams

Schematic

Cargo Lamp
For further information regarding this component please refer to Lighting and Horns System Information. See See: Lighting and
Horns/Diagrams/Electrical Diagrams
Reference to System Information
For further information regarding this component please refer to Lighting and Horns System Information. See See: Lighting and
Horns/Diagrams/Electrical Diagrams

Center High Mounted Stop Lamp (CHMSL)

Courtesy Lamp
For further information regarding this component please refer to Lighting and Horns System Information. See See: Lighting and
Horns/Diagrams/Electrical Diagrams
Daytime Running Lamp
Refer to "Lighting and Horns" See: Lighting and Horns/Diagrams/Electrical Diagrams
Dimmer Switch
For further information regarding this component please refer to Lighting and Horns System Information. See See: Lighting and
Horns/Diagrams/Electrical Diagrams
Dome Lamp
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 303
Chevrolet Venture V6-3.4L VIN E 1379
For further information regarding this component please refer to Lighting and Horns System Information. See See: Lighting and
Horns/Diagrams/Electrical Diagrams
Fog/Driving Lamp
For further information regarding this component please refer to Lighting and Horns System Information. See See: Lighting and
Horns/Diagrams/Electrical Diagrams
Hazard Warning Lamps
For further information regarding this component please refer to Lighting and Horns System Information. See See: Lighting and
Horns/Diagrams/Electrical Diagrams
Headlamp
Refer to "Lighting and Horns" See: Lighting and Horns/Diagrams/Electrical Diagrams

Horns Schematics (Horns)

License Plate Lamp


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 304
Chevrolet Venture V6-3.4L VIN E 1380
For further information regarding this component please refer to Lighting and Horns System Information. See See: Lighting and
Horns/Diagrams/Electrical Diagrams
Map Light
For further information regarding this component please refer to Lighting and Horns System Information. See See: Lighting and
Horns/Diagrams/Electrical Diagrams
Marker Lamp
For further information regarding this component please refer to Lighting and Horns System Information. See See: Lighting and
Horns/Diagrams/Electrical Diagrams
Parking Lamp
For further information regarding this component please refer to Lighting and Horns System Information. See See: Lighting and
Horns/Diagrams/Electrical Diagrams
Tail Lamp
For further information regarding this component please refer to Lighting and Horns System Information. See See: Lighting and
Horns/Diagrams/Electrical Diagrams
Turn Signals
For further information regarding this component please refer to Lighting and Horns System Information. See See: Lighting and
Horns/Diagrams/Electrical Diagrams
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 305
Chevrolet Venture V6-3.4L VIN E 1381

Door Lock/Indicator Schematics: Door Lock Switches


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 306
Chevrolet Venture V6-3.4L VIN E 1382

Door Lock/Indicator Schematics: Key Cylinder Switches


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 307
Chevrolet Venture V6-3.4L VIN E 1383

Door Lock/Indicator Schematics: Door Lock Actuators


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 308
Chevrolet Venture V6-3.4L VIN E 1384

Door Lock/Indicator Schematics: IP DOOR AJAR Telltale


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 309
Chevrolet Venture V6-3.4L VIN E 1385

Keyless Entry Schematics


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 310
Chevrolet Venture V6-3.4L VIN E 1386

Door Lock/Indicator Schematics: Door Lock Switches


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 311
Chevrolet Venture V6-3.4L VIN E 1387

Door Lock/Indicator Schematics: Key Cylinder Switches


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 312
Chevrolet Venture V6-3.4L VIN E 1388

Door Lock/Indicator Schematics: Door Lock Actuators


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 313
Chevrolet Venture V6-3.4L VIN E 1389

Door Lock/Indicator Schematics: IP DOOR AJAR Telltale

Power Door Lock Actuator


For further information regarding this component please refer to Body and Frame, Door System Information. See
Power Door Lock Switch
For further information regarding this component please refer to Body and Frame, Door System Information. See
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 314
Chevrolet Venture V6-3.4L VIN E 1390

Outside Mirror Schematics: Power Mirrors


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 315
Chevrolet Venture V6-3.4L VIN E 1391

Outside Mirror Schematics: Heated Mirrors


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 316
Chevrolet Venture V6-3.4L VIN E 1392

Schematic

Schematic
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 317
Chevrolet Venture V6-3.4L VIN E 1393

Engine Controls Schematics: IAC Valve, EBTCM, Engine Oil Level Sensor
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 318
Chevrolet Venture V6-3.4L VIN E 1394

Schematic
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 319
Chevrolet Venture V6-3.4L VIN E 1395

Engine Controls Schematics: Engine Data Sensors, MAF, EVAP Switch, EVAP Valve, EGR
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 320
Chevrolet Venture V6-3.4L VIN E 1396

Schematic
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 321
Chevrolet Venture V6-3.4L VIN E 1397

Engine Controls Schematics: Engine Data Sensors, MAF, EVAP Switch, EVAP Valve, EGR
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 322
Chevrolet Venture V6-3.4L VIN E 1398

Schematic
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 323
Chevrolet Venture V6-3.4L VIN E 1399

Schematic
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 324
Chevrolet Venture V6-3.4L VIN E 1400

Engine Controls Schematics: Engine Data Sensors, A/C Refrig Press, TP, MAP, ECT, IAT
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 325
Chevrolet Venture V6-3.4L VIN E 1401

Schematic
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 326
Chevrolet Venture V6-3.4L VIN E 1402

Data Link Connector (DLC) Schematics


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 327
Chevrolet Venture V6-3.4L VIN E 1403

Engine Controls Schematics: Power, Ground, MIL, DLC


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 328
Chevrolet Venture V6-3.4L VIN E 1404

Engine Controls Schematics: Coolant Fans


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 329
Chevrolet Venture V6-3.4L VIN E 1405

Schematic
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 330
Chevrolet Venture V6-3.4L VIN E 1406

Schematic
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 331
Chevrolet Venture V6-3.4L VIN E 1407

Schematic
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 332
Chevrolet Venture V6-3.4L VIN E 1408

Engine Controls Schematics: Engine Data Sensors, MAF, HO2S1, HO2S2


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 333
Chevrolet Venture V6-3.4L VIN E 1409

Engine Controls Schematics: A/C Compressor Controls


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 334
Chevrolet Venture V6-3.4L VIN E 1410

Engine Controls Schematics: IAC Valve, EBTCM, Engine Oil Level Sensor
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 335
Chevrolet Venture V6-3.4L VIN E 1411

Engine Controls Schematics: Ignition System, Knock Sensor


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 336
Chevrolet Venture V6-3.4L VIN E 1412

Engine Controls Schematics: Ignition System, Knock Sensor


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 337
Chevrolet Venture V6-3.4L VIN E 1413

Body Control Module Schematics (BCM: Ignition Input, Door Locks, Exterior Lamps Output)
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 338
Chevrolet Venture V6-3.4L VIN E 1414

Engine Controls Schematics: Engine Data Sensors, MAF, EVAP Switch, EVAP Valve, EGR
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 339
Chevrolet Venture V6-3.4L VIN E 1415

Engine Controls Schematics: Fuel Control


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 340
Chevrolet Venture V6-3.4L VIN E 1416

Engine Controls Schematics: Fuel Injectors


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 341
Chevrolet Venture V6-3.4L VIN E 1417

Engine Controls Schematics: Fuel Control


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 342
Chevrolet Venture V6-3.4L VIN E 1418

Schematic

Schematic

Transmission Controls
For information regarding Diagrams for this system, please refer to Transmission Control Systems diagrams. See: Powertrain
Management/Transmission Control Systems/Diagrams/Electrical Diagrams
System Diagram
For information regarding diagrams for this component, please refer to Powertrain Managment Diagrams. See: Powertrain
Management/Diagrams/Electrical Diagrams
Air Flow Meter/Sensor
For information regarding diagrams for this component, please refer to Powertrain Managment Diagrams. See: Powertrain
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 343
Chevrolet Venture V6-3.4L VIN E 1419
Management/Diagrams/Electrical Diagrams

Body Control Module Schematics (BCM: Interior Lights On Request, Horn Control)

Camshaft Position Sensor


For information regarding diagrams for this component, please refer to Powertrain Managment Diagrams. See: Powertrain
Management/Diagrams/Electrical Diagrams
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 344
Chevrolet Venture V6-3.4L VIN E 1420

Schematic

Crankshaft Position Sensor


For information regarding diagrams for this component, please refer to Powertrain Managment Diagrams. See: Powertrain
Management/Diagrams/Electrical Diagrams
Engine Control Module
For information regarding diagrams for this component, please refer to Powertrain Managment Diagrams. See: Powertrain
Management/Diagrams/Electrical Diagrams

Schematic
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 345
Chevrolet Venture V6-3.4L VIN E 1421

Schematic

Schematic

Schematic
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 346
Chevrolet Venture V6-3.4L VIN E 1422

Engine Controls Schematics: Engine Data Sensors, MAF, HO2S1, HO2S2


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 347
Chevrolet Venture V6-3.4L VIN E 1423

Schematic
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 348
Chevrolet Venture V6-3.4L VIN E 1424

Engine Controls Schematics: Engine Data Sensors, MAF, HO2S1, HO2S2


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 349
Chevrolet Venture V6-3.4L VIN E 1425

Schematic

Throttle Position Sensor


For information regarding diagrams for this component, please refer to Powertrain Managment Diagrams. See: Powertrain
Management/Diagrams/Electrical Diagrams
Vehicle Speed Sensor
For information regarding diagrams for this component, please refer to Powertrain Managment Diagrams. See: Powertrain
Management/Diagrams/Electrical Diagrams
System Diagram
For information regarding diagrams for this component, please refer to Powertrain Managment Diagrams. See: Powertrain
Management/Diagrams/Electrical Diagrams
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 350
Chevrolet Venture V6-3.4L VIN E 1426

Engine Controls Schematics: Engine Data Sensors, MAF, EVAP Switch, EVAP Valve, EGR
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 351
Chevrolet Venture V6-3.4L VIN E 1427

Schematic

System Diagram
For information regarding diagrams for this component, please refer to Powertrain Managment Diagrams. See: Powertrain
Management/Diagrams/Electrical Diagrams
Fuel Injector
For information regarding diagrams for this component, please refer to Powertrain Managment Diagrams. See: Powertrain
Management/Diagrams/Electrical Diagrams
System Diagram
For information regarding diagrams for this component, please refer to Powertrain Managment Diagrams. See: Powertrain
Management/Diagrams/Electrical Diagrams
Fuel Pump Relay
For information regarding diagrams for this component, please refer to Powertrain Managment Diagrams. See: Powertrain
Management/Diagrams/Electrical Diagrams
Ignition System
For information regarding diagrams for this component, please refer to Powertrain Managment Diagrams. See: Powertrain
Management/Diagrams/Electrical Diagrams
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 352
Chevrolet Venture V6-3.4L VIN E 1428

Cooling Fan Schematics


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 353
Chevrolet Venture V6-3.4L VIN E 1429

Cooling Fan Schematics


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 354
Chevrolet Venture V6-3.4L VIN E 1430

Engine Controls Schematics: Coolant Fans


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 355
Chevrolet Venture V6-3.4L VIN E 1431

Radio/Audio System Schematics: G201


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 356
Chevrolet Venture V6-3.4L VIN E 1432

Radio/Audio System Schematics: Windshield Antenna


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 357
Chevrolet Venture V6-3.4L VIN E 1433

Radio/Audio System Schematics: Right And Left Radio Liftgate Speaker (Base)
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 358
Chevrolet Venture V6-3.4L VIN E 1434

Radio/Audio System Schematics: Right And Left Radio Liftgate Speaker (Uplevel)
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 359
Chevrolet Venture V6-3.4L VIN E 1435

Video System Schematics: Power And Ground Distribution (Early Design)


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 360
Chevrolet Venture V6-3.4L VIN E 1436

Video System Schematics: Power And Ground Distribution (Later Design)


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 361
Chevrolet Venture V6-3.4L VIN E 1437

Video System Schematics: Power And Ground Distribution (Interface Module)


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 362
Chevrolet Venture V6-3.4L VIN E 1438

Video System Schematics: Video Cassette Player (VCP) To Auxiliary Video Module (AVM) Inputs)
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 363
Chevrolet Venture V6-3.4L VIN E 1439

Video System Schematics: Video Screen Controls


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 364
Chevrolet Venture V6-3.4L VIN E 1440

Video System Schematics: Rear Seat Audio (RSA) Enabling Circuits


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 365
Chevrolet Venture V6-3.4L VIN E 1441

Video System Schematics: Radio Audio Channel Outputs


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 366
Chevrolet Venture V6-3.4L VIN E 1442

Video System Schematics: Radio Audio Channel Outputs


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 367
Chevrolet Venture V6-3.4L VIN E 1443

Video System Schematics: Video Audio Channel Outputs


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 368
Chevrolet Venture V6-3.4L VIN E 1444

Video System Schematics: Rear Speaker Outputs


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 369
Chevrolet Venture V6-3.4L VIN E 1445

Video System Schematics: Interior Lights Dimming


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 370
Chevrolet Venture V6-3.4L VIN E 1446

Video System Schematics: Seat Audio Controls Mechanization

Rear Defogger
For information regarding this component and the system that it is a part of, please refer to Heated Glass Element, See: Windows and
Glass/Heated Glass Element/Diagrams/Electrical Diagrams
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 371
Chevrolet Venture V6-3.4L VIN E 1447

Seat Belt Schematics


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 372
Chevrolet Venture V6-3.4L VIN E 1448

Power Seats Schematics: Power Seats Schematics Driver's Side


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 373
Chevrolet Venture V6-3.4L VIN E 1449

Power Seats Schematics: Power Seats Schematics Passenger's Side


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 374
Chevrolet Venture V6-3.4L VIN E 1450

Heated Seats Schematics: Driver Seat Heater Module, Heated Seat Switches
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 375
Chevrolet Venture V6-3.4L VIN E 1451

Heated Seats Schematics: Passenger Seat Heater Module


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 376
Chevrolet Venture V6-3.4L VIN E 1452

Power Sliding Door (PSD) Schematics: Power, Ground, PSD Motor


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 377
Chevrolet Venture V6-3.4L VIN E 1453

Power Sliding Door (PSD) Schematics: PSD Switches, Transaxle Range Switch, RKE
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 378
Chevrolet Venture V6-3.4L VIN E 1454

Starting And Charging Schematics: Charging


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 379
Chevrolet Venture V6-3.4L VIN E 1455

Starting And Charging Schematics: Starting


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 380
Chevrolet Venture V6-3.4L VIN E 1456

ower Distribution Schematics: Ignition Switch, IGN Main 2, BCM PRORM, RR WPR/WSHR, MALL/Cluster And FRT/WPR/WSHR Fuse
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 381
Chevrolet Venture V6-3.4L VIN E 1457

Power Distribution Schematics: Ignition Switch IGN Main Relay, IGN Main 1, PCM/ABS, CONVENT SOL, DRL, And PCM/Crank Fuses
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 382
Chevrolet Venture V6-3.4L VIN E 1458

Cigar Lighter/Auxiliary Outlets Schematics


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 383
Chevrolet Venture V6-3.4L VIN E 1459

Power Distribution Schematics: Underhood Accessory Wiring Junction Block, Relay Center, PWR WDO And PWR OTR Vent Fuses
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 384
Chevrolet Venture V6-3.4L VIN E 1460

Power Distribution Schematics: Stop Lamp, Hazard, And PassKey Fuses, FRT HVAC MI BLWR And Headlamp Circuit Breakers
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 385
Chevrolet Venture V6-3.4L VIN E 1461

bution Schematics: BATT Main 2, Headlamps, ELC/Trailer, RR Defog/HTP Mirrors And RR Fog LP Fuses And PWR/Heated Seat PSD Cir

General Information
Schematics break the electrical system into individual circuits, showing the electrical current paths when a circuit is operating properly. Wiring
circuits that are continued with references, "A - Z" and "AB - AZ" are linked directly to the continuation of that circuit. These links can be
especially useful in identifying the power distribution and circuit protection devices between the component and the battery, or the connectors and
splices between the component and its ground.

These references can be followed by clicking on the highlighted portion of the diagram, which will take you from one end of the circuit to the other.
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 386
Chevrolet Venture V6-3.4L VIN E 1462

bution Schematics: BATT Main 2, Headlamps, ELC/Trailer, RR Defog/HTP Mirrors And RR Fog LP Fuses And PWR/Heated Seat PSD Cir
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 387
Chevrolet Venture V6-3.4L VIN E 1463

stribution Schematics: Cluster BATT, RR PWR SCKT, PWR Lock, Rap Relay, CTSY Lamp, FRT PWR SCKT, Cigar/DLC And PWR Mir
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 388
Chevrolet Venture V6-3.4L VIN E 1464

stribution Schematics: Cluster BATT, RR PWR SCKT, PWR Lock, Rap Relay, CTSY Lamp, FRT PWR SCKT, Cigar/DLC And PWR Mir
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 389
Chevrolet Venture V6-3.4L VIN E 1465

Power Distribution Schematics: Ignition Switch IGN Main Relay, IGN Main 1, PCM/ABS, CONVENT SOL, DRL, And PCM/Crank Fuses
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 390
Chevrolet Venture V6-3.4L VIN E 1466

Power Distribution Schematics: Stop Lamp, Hazard, And PassKey Fuses, FRT HVAC MI BLWR And Headlamp Circuit Breakers
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 391
Chevrolet Venture V6-3.4L VIN E 1467

Power Distribution Schematics: Stop Lamp, Hazard, And PassKey Fuses, FRT HVAC MI BLWR And Headlamp Circuit Breakers
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 392
Chevrolet Venture V6-3.4L VIN E 1468

Power Distribution Schematics: HVAC/DIC/DRL/Heated Seat, HVAC Blower And RR HVAC/TEMP CONT Fuses
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 393
Chevrolet Venture V6-3.4L VIN E 1469

Power Distribution Schematics: Ignition Switch IGN Main Relay, IGN Main 1, PCM/ABS, CONVENT SOL, DRL, And PCM/Crank Fuses
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 394
Chevrolet Venture V6-3.4L VIN E 1470

ower Distribution Schematics: Ignition Switch, IGN Main 2, BCM PRORM, RR WPR/WSHR, MALL/Cluster And FRT/WPR/WSHR Fuse
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 395
Chevrolet Venture V6-3.4L VIN E 1471

Power Distribution Schematics: IGN, SIR, T/S/G, Cruise, And PCM/PassKey 1 Cluster Fuses
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 396
Chevrolet Venture V6-3.4L VIN E 1472

stribution Schematics: (Export Only) LH T/LP, RH T/LP, LH HEAD LP High, RH HEAD LP High, LH Head LP Low, And RH Head LP L
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 397
Chevrolet Venture V6-3.4L VIN E 1473

stribution Schematics: (Export Only) LH T/LP, RH T/LP, LH HEAD LP High, RH HEAD LP High, LH Head LP Low, And RH Head LP L
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 398
Chevrolet Venture V6-3.4L VIN E 1474

ower Distribution Schematics: Ignition Switch, IGN Main 2, BCM PRORM, RR WPR/WSHR, MALL/Cluster And FRT/WPR/WSHR Fuse
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 399
Chevrolet Venture V6-3.4L VIN E 1475

bution Schematics: BATT Main 2, Headlamps, ELC/Trailer, RR Defog/HTP Mirrors And RR Fog LP Fuses And PWR/Heated Seat PSD Cir
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 400
Chevrolet Venture V6-3.4L VIN E 1476

bution Schematics: BATT Main 2, Headlamps, ELC/Trailer, RR Defog/HTP Mirrors And RR Fog LP Fuses And PWR/Heated Seat PSD Cir
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 401
Chevrolet Venture V6-3.4L VIN E 1477

Power Distribution Schematics: Stop Lamp, Hazard, And PassKey Fuses, FRT HVAC MI BLWR And Headlamp Circuit Breakers
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 402
Chevrolet Venture V6-3.4L VIN E 1478

Power Distribution Schematics: SWC Backlight And HTO Mirror Fuses


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 403
Chevrolet Venture V6-3.4L VIN E 1479

bution Schematics: BATT Main 2, Headlamps, ELC/Trailer, RR Defog/HTP Mirrors And RR Fog LP Fuses And PWR/Heated Seat PSD Cir
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 404
Chevrolet Venture V6-3.4L VIN E 1480

Power Distribution Schematics: Ignition Switch IGN Main Relay, IGN Main 1, PCM/ABS, CONVENT SOL, DRL, And PCM/Crank Fuses
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 405
Chevrolet Venture V6-3.4L VIN E 1481

Power Distribution Schematics: EBCM, BATT Main 1 And Radio Fuses


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 406
Chevrolet Venture V6-3.4L VIN E 1482

Power Distribution Schematics: Ignition Switch IGN Main Relay, IGN Main 1, PCM/ABS, CONVENT SOL, DRL, And PCM/Crank Fuses
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 407
Chevrolet Venture V6-3.4L VIN E 1483

ower Distribution Schematics: Ignition Switch, IGN Main 2, BCM PRORM, RR WPR/WSHR, MALL/Cluster And FRT/WPR/WSHR Fuse
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 408
Chevrolet Venture V6-3.4L VIN E 1484

ower Distribution Schematics: Ignition Switch, IGN Main 2, BCM PRORM, RR WPR/WSHR, MALL/Cluster And FRT/WPR/WSHR Fuse
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 409
Chevrolet Venture V6-3.4L VIN E 1485

Power Distribution Schematics: Underhood Accessory Wiring Junction Block, Relay Center, PWR WDO And PWR OTR Vent Fuses
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 410
Chevrolet Venture V6-3.4L VIN E 1486

bution Schematics: BATT Main 2, Headlamps, ELC/Trailer, RR Defog/HTP Mirrors And RR Fog LP Fuses And PWR/Heated Seat PSD Cir
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 411
Chevrolet Venture V6-3.4L VIN E 1487

bution Schematics: BATT Main 2, Headlamps, ELC/Trailer, RR Defog/HTP Mirrors And RR Fog LP Fuses And PWR/Heated Seat PSD Cir
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 412
Chevrolet Venture V6-3.4L VIN E 1488

Power Distribution Schematics: Under Accessory Wiring Junction Block


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 413
Chevrolet Venture V6-3.4L VIN E 1489

Power Distribution Schematics: Under Accessory Wiring Junction Block And IGN 1 Fuse
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 414
Chevrolet Venture V6-3.4L VIN E 1490

Power Distribution Schematics: Under Accessory Wiring Junction Block And INJ Fuse
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 415
Chevrolet Venture V6-3.4L VIN E 1491

Power Distribution Schematics: Underhood Accessory Wiring Junction Block, Relay Center, PWR WDO And PWR OTR Vent Fuses
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 416
Chevrolet Venture V6-3.4L VIN E 1492

Power Distribution Schematics: Underhood Accessory Wiring Junction Block


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 417
Chevrolet Venture V6-3.4L VIN E 1493

Power Distribution Schematics: Underhood Accessory Wiring Junction Block


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 418
Chevrolet Venture V6-3.4L VIN E 1494

Power Distribution Schematics: Underhood Accessory Wiring Junction Block, Relay Center, PWR WDO And PWR OTR Vent Fuses
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 419
Chevrolet Venture V6-3.4L VIN E 1495

Power Distribution Schematics: Underhood Accessory Wiring Junction Block, Relay Center, PWR WDO And PWR OTR Vent Fuses
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 420
Chevrolet Venture V6-3.4L VIN E 1496

Power Distribution Schematics: Underhood Accessory Wiring Junction Block, Relay Center, PWR WDO And PWR OTR Vent Fuses
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 421
Chevrolet Venture V6-3.4L VIN E 1497

Power Distribution Schematics: EBCM, BATT Main 1 And Radio Fuses


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 422
Chevrolet Venture V6-3.4L VIN E 1498

bution Schematics: BATT Main 2, Headlamps, ELC/Trailer, RR Defog/HTP Mirrors And RR Fog LP Fuses And PWR/Heated Seat PSD Cir
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 423
Chevrolet Venture V6-3.4L VIN E 1499

ower Distribution Schematics: Ignition Switch, IGN Main 2, BCM PRORM, RR WPR/WSHR, MALL/Cluster And FRT/WPR/WSHR Fuse
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 424
Chevrolet Venture V6-3.4L VIN E 1500

Power Distribution Schematics: Ignition Switch IGN Main Relay, IGN Main 1, PCM/ABS, CONVENT SOL, DRL, And PCM/Crank Fuses
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 425
Chevrolet Venture V6-3.4L VIN E 1501

stribution Schematics: Cluster BATT, RR PWR SCKT, PWR Lock, Rap Relay, CTSY Lamp, FRT PWR SCKT, Cigar/DLC And PWR Mir
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 426
Chevrolet Venture V6-3.4L VIN E 1502

Cigar Lighter/Auxiliary Outlets Schematics


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 427
Chevrolet Venture V6-3.4L VIN E 1503

Power Distribution Schematics: IGN, SIR, T/S/G, Cruise, And PCM/PassKey 1 Cluster Fuses
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 428
Chevrolet Venture V6-3.4L VIN E 1504

stribution Schematics: Cluster BATT, RR PWR SCKT, PWR Lock, Rap Relay, CTSY Lamp, FRT PWR SCKT, Cigar/DLC And PWR Mir
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 429
Chevrolet Venture V6-3.4L VIN E 1505

stribution Schematics: Cluster BATT, RR PWR SCKT, PWR Lock, Rap Relay, CTSY Lamp, FRT PWR SCKT, Cigar/DLC And PWR Mir
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 430
Chevrolet Venture V6-3.4L VIN E 1506

Power Distribution Schematics: Ignition Switch IGN Main Relay, IGN Main 1, PCM/ABS, CONVENT SOL, DRL, And PCM/Crank Fuses
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 431
Chevrolet Venture V6-3.4L VIN E 1507

Power Distribution Schematics: IGN, SIR, T/S/G, Cruise, And PCM/PassKey 1 Cluster Fuses
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 432
Chevrolet Venture V6-3.4L VIN E 1508

stribution Schematics: Cluster BATT, RR PWR SCKT, PWR Lock, Rap Relay, CTSY Lamp, FRT PWR SCKT, Cigar/DLC And PWR Mir
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 433
Chevrolet Venture V6-3.4L VIN E 1509

Power Distribution Schematics: HVAC/DIC/DRL/Heated Seat, HVAC Blower And RR HVAC/TEMP CONT Fuses
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 434
Chevrolet Venture V6-3.4L VIN E 1510

Power Distribution Schematics: Ignition Switch IGN Main Relay, IGN Main 1, PCM/ABS, CONVENT SOL, DRL, And PCM/Crank Fuses
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 435
Chevrolet Venture V6-3.4L VIN E 1511

Power Distribution Schematics: HVAC/DIC/DRL/Heated Seat, HVAC Blower And RR HVAC/TEMP CONT Fuses
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 436
Chevrolet Venture V6-3.4L VIN E 1512

Power Distribution Schematics: EBCM, BATT Main 1 And Radio Fuses


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 437
Chevrolet Venture V6-3.4L VIN E 1513

Power Distribution Schematics: Underhood Accessory Wiring Junction Block, Relay Center, PWR WDO And PWR OTR Vent Fuses
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 438
Chevrolet Venture V6-3.4L VIN E 1514

bution Schematics: BATT Main 2, Headlamps, ELC/Trailer, RR Defog/HTP Mirrors And RR Fog LP Fuses And PWR/Heated Seat PSD Cir
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 439
Chevrolet Venture V6-3.4L VIN E 1515

Power Distribution Schematics: Underhood Accessory Wiring Junction Block


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 440
Chevrolet Venture V6-3.4L VIN E 1516

Power Distribution Schematics: Underhood Accessory Wiring Junction Block


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 441
Chevrolet Venture V6-3.4L VIN E 1517

stribution Schematics: Cluster BATT, RR PWR SCKT, PWR Lock, Rap Relay, CTSY Lamp, FRT PWR SCKT, Cigar/DLC And PWR Mir
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 442
Chevrolet Venture V6-3.4L VIN E 1518

Cigar Lighter/Auxiliary Outlets Schematics


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 443
Chevrolet Venture V6-3.4L VIN E 1519

ower Distribution Schematics: Ignition Switch, IGN Main 2, BCM PRORM, RR WPR/WSHR, MALL/Cluster And FRT/WPR/WSHR Fuse
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 444
Chevrolet Venture V6-3.4L VIN E 1520

Power Distribution Schematics: Underhood Accessory Wiring Junction Block


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 445
Chevrolet Venture V6-3.4L VIN E 1521

Power Distribution Schematics: Stop Lamp, Hazard, And PassKey Fuses, FRT HVAC MI BLWR And Headlamp Circuit Breakers
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 446
Chevrolet Venture V6-3.4L VIN E 1522

bution Schematics: BATT Main 2, Headlamps, ELC/Trailer, RR Defog/HTP Mirrors And RR Fog LP Fuses And PWR/Heated Seat PSD Cir
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 447
Chevrolet Venture V6-3.4L VIN E 1523

Power Distribution Schematics: HVAC/DIC/DRL/Heated Seat, HVAC Blower And RR HVAC/TEMP CONT Fuses
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 448
Chevrolet Venture V6-3.4L VIN E 1524

Power Distribution Schematics: Underhood Accessory Wiring Junction Block


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 449
Chevrolet Venture V6-3.4L VIN E 1525

Power Distribution Schematics: SWC Backlight And HTO Mirror Fuses


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 450
Chevrolet Venture V6-3.4L VIN E 1526

bution Schematics: BATT Main 2, Headlamps, ELC/Trailer, RR Defog/HTP Mirrors And RR Fog LP Fuses And PWR/Heated Seat PSD Cir
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 451
Chevrolet Venture V6-3.4L VIN E 1527

Power Distribution Schematics: HVAC/DIC/DRL/Heated Seat, HVAC Blower And RR HVAC/TEMP CONT Fuses
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 452
Chevrolet Venture V6-3.4L VIN E 1528

Power Distribution Schematics: Stop Lamp, Hazard, And PassKey Fuses, FRT HVAC MI BLWR And Headlamp Circuit Breakers
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 453
Chevrolet Venture V6-3.4L VIN E 1529

Power Distribution Schematics: HVAC/DIC/DRL/Heated Seat, HVAC Blower And RR HVAC/TEMP CONT Fuses
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 454
Chevrolet Venture V6-3.4L VIN E 1530

Power Distribution Schematics: IGN, SIR, T/S/G, Cruise, And PCM/PassKey 1 Cluster Fuses
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 455
Chevrolet Venture V6-3.4L VIN E 1531

Power Distribution Schematics: Ignition Switch IGN Main Relay, IGN Main 1, PCM/ABS, CONVENT SOL, DRL, And PCM/Crank Fuses
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 456
Chevrolet Venture V6-3.4L VIN E 1532

ower Distribution Schematics: Ignition Switch, IGN Main 2, BCM PRORM, RR WPR/WSHR, MALL/Cluster And FRT/WPR/WSHR Fuse
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 457
Chevrolet Venture V6-3.4L VIN E 1533

ower Distribution Schematics: Ignition Switch, IGN Main 2, BCM PRORM, RR WPR/WSHR, MALL/Cluster And FRT/WPR/WSHR Fuse
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 458
Chevrolet Venture V6-3.4L VIN E 1534

Power Distribution Schematics: Underhood Accessory Wiring Junction Block


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 459
Chevrolet Venture V6-3.4L VIN E 1535

Power Distribution Schematics: IGN, SIR, T/S/G, Cruise, And PCM/PassKey 1 Cluster Fuses
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 460
Chevrolet Venture V6-3.4L VIN E 1536

Power Distribution Schematics: Under Accessory Wiring Junction Block And IGN 1 Fuse
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 461
Chevrolet Venture V6-3.4L VIN E 1537

Power Distribution Schematics: Underhood Accessory Wiring Junction Block


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 462
Chevrolet Venture V6-3.4L VIN E 1538

Power Distribution Schematics: Under Accessory Wiring Junction Block And INJ Fuse
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 463
Chevrolet Venture V6-3.4L VIN E 1539

stribution Schematics: (Export Only) LH T/LP, RH T/LP, LH HEAD LP High, RH HEAD LP High, LH Head LP Low, And RH Head LP L
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 464
Chevrolet Venture V6-3.4L VIN E 1540

stribution Schematics: (Export Only) LH T/LP, RH T/LP, LH HEAD LP High, RH HEAD LP High, LH Head LP Low, And RH Head LP L
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 465
Chevrolet Venture V6-3.4L VIN E 1541

stribution Schematics: (Export Only) LH T/LP, RH T/LP, LH HEAD LP High, RH HEAD LP High, LH Head LP Low, And RH Head LP L
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 466
Chevrolet Venture V6-3.4L VIN E 1542

ower Distribution Schematics: Ignition Switch, IGN Main 2, BCM PRORM, RR WPR/WSHR, MALL/Cluster And FRT/WPR/WSHR Fuse
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 467
Chevrolet Venture V6-3.4L VIN E 1543

Power Distribution Schematics: EBCM, BATT Main 1 And Radio Fuses


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 468
Chevrolet Venture V6-3.4L VIN E 1544

Power Distribution Schematics: EBCM, BATT Main 1 And Radio Fuses

General Information
Schematics break the electrical system into individual circuits, showing the electrical current paths when a circuit is operating properly. Wiring
circuits that are continued with references, "A - Z" and "AB - AZ" are linked directly to the continuation of that circuit. These links can be
especially useful in identifying the power distribution and circuit protection devices between the component and the battery, or the connectors and
splices between the component and its ground.

These references can be followed by clicking on the highlighted portion of the diagram, which will take you from one end of the circuit to the other.
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 469
Chevrolet Venture V6-3.4L VIN E 1545

Power Distribution Schematics: EBCM, BATT Main 1 And Radio Fuses


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 470
Chevrolet Venture V6-3.4L VIN E 1546

stribution Schematics: Cluster BATT, RR PWR SCKT, PWR Lock, Rap Relay, CTSY Lamp, FRT PWR SCKT, Cigar/DLC And PWR Mir
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 471
Chevrolet Venture V6-3.4L VIN E 1547

Ground Distribution Schematics: G200


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 472
Chevrolet Venture V6-3.4L VIN E 1548

Ground Distribution Schematics: G200


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 473
Chevrolet Venture V6-3.4L VIN E 1549

bution Schematics: BATT Main 2, Headlamps, ELC/Trailer, RR Defog/HTP Mirrors And RR Fog LP Fuses And PWR/Heated Seat PSD Cir
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 474
Chevrolet Venture V6-3.4L VIN E 1550

Power Distribution Schematics: Stop Lamp, Hazard, And PassKey Fuses, FRT HVAC MI BLWR And Headlamp Circuit Breakers
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 475
Chevrolet Venture V6-3.4L VIN E 1551

Ground Distribution Schematics: G200


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 476
Chevrolet Venture V6-3.4L VIN E 1552

Ground Distribution Schematics: G200


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 477
Chevrolet Venture V6-3.4L VIN E 1553

Ground Distribution Schematics: G200


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 478
Chevrolet Venture V6-3.4L VIN E 1554

ower Distribution Schematics: Ignition Switch, IGN Main 2, BCM PRORM, RR WPR/WSHR, MALL/Cluster And FRT/WPR/WSHR Fuse
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 479
Chevrolet Venture V6-3.4L VIN E 1555

Power Distribution Schematics: Underhood Accessory Wiring Junction Block, Relay Center, PWR WDO And PWR OTR Vent Fuses
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 480
Chevrolet Venture V6-3.4L VIN E 1556

Ground Distribution Schematics: G200


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 481
Chevrolet Venture V6-3.4L VIN E 1557

Ground Distribution Schematics: G200


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 482
Chevrolet Venture V6-3.4L VIN E 1558

Ground Distribution Schematics: G200


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 483
Chevrolet Venture V6-3.4L VIN E 1559

ower Distribution Schematics: Ignition Switch, IGN Main 2, BCM PRORM, RR WPR/WSHR, MALL/Cluster And FRT/WPR/WSHR Fuse
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 484
Chevrolet Venture V6-3.4L VIN E 1560

Ground Distribution Schematics: G200 And G201


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 485
Chevrolet Venture V6-3.4L VIN E 1561

Power Distribution Schematics: HVAC/DIC/DRL/Heated Seat, HVAC Blower And RR HVAC/TEMP CONT Fuses
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 486
Chevrolet Venture V6-3.4L VIN E 1562

Ground Distribution Schematics: G200


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 487
Chevrolet Venture V6-3.4L VIN E 1563

stribution Schematics: Cluster BATT, RR PWR SCKT, PWR Lock, Rap Relay, CTSY Lamp, FRT PWR SCKT, Cigar/DLC And PWR Mir
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 488
Chevrolet Venture V6-3.4L VIN E 1564

Ground Distribution Schematics: G302


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 489
Chevrolet Venture V6-3.4L VIN E 1565

Power Distribution Schematics: Underhood Accessory Wiring Junction Block, Relay Center, PWR WDO And PWR OTR Vent Fuses
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 490
Chevrolet Venture V6-3.4L VIN E 1566

Ground Distribution Schematics: G302


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 491
Chevrolet Venture V6-3.4L VIN E 1567

Power Distribution Schematics: Underhood Accessory Wiring Junction Block


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 492
Chevrolet Venture V6-3.4L VIN E 1568

Power Distribution Schematics: Underhood Accessory Wiring Junction Block, Relay Center, PWR WDO And PWR OTR Vent Fuses
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 493
Chevrolet Venture V6-3.4L VIN E 1569

Ground Distribution Schematics: G302


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 494
Chevrolet Venture V6-3.4L VIN E 1570

Ground Distribution Schematics: G302


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 495
Chevrolet Venture V6-3.4L VIN E 1571

Power Distribution Schematics: Ignition Switch IGN Main Relay, IGN Main 1, PCM/ABS, CONVENT SOL, DRL, And PCM/Crank Fuses
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 496
Chevrolet Venture V6-3.4L VIN E 1572

Ground Distribution Schematics: G401


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 497
Chevrolet Venture V6-3.4L VIN E 1573

Power Distribution Schematics: IGN, SIR, T/S/G, Cruise, And PCM/PassKey 1 Cluster Fuses
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 498
Chevrolet Venture V6-3.4L VIN E 1574

Ground Distribution Schematics: G401 And G402


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 499
Chevrolet Venture V6-3.4L VIN E 1575

Power Distribution Schematics: Ignition Switch IGN Main Relay, IGN Main 1, PCM/ABS, CONVENT SOL, DRL, And PCM/Crank Fuses
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 500
Chevrolet Venture V6-3.4L VIN E 1576

Ground Distribution Schematics: G401


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 501
Chevrolet Venture V6-3.4L VIN E 1577

Power Distribution Schematics: IGN, SIR, T/S/G, Cruise, And PCM/PassKey 1 Cluster Fuses
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 502
Chevrolet Venture V6-3.4L VIN E 1578

Ground Distribution Schematics: G401 And G402


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 503
Chevrolet Venture V6-3.4L VIN E 1579

Power Distribution Schematics: Underhood Accessory Wiring Junction Block


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 504
Chevrolet Venture V6-3.4L VIN E 1580

Power Distribution Schematics: Under Accessory Wiring Junction Block And IGN 1 Fuse
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 505
Chevrolet Venture V6-3.4L VIN E 1581

Power Distribution Schematics: Underhood Accessory Wiring Junction Block


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 506
Chevrolet Venture V6-3.4L VIN E 1582

Power Distribution Schematics: Under Accessory Wiring Junction Block And INJ Fuse
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 507
Chevrolet Venture V6-3.4L VIN E 1583

Power Distribution Schematics: Under Accessory Wiring Junction Block


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 508
Chevrolet Venture V6-3.4L VIN E 1584

Power Distribution Schematics: Underhood Accessory Wiring Junction Block


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 509
Chevrolet Venture V6-3.4L VIN E 1585

Power Distribution Schematics: Underhood Accessory Wiring Junction Block


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 510
Chevrolet Venture V6-3.4L VIN E 1586

Power Distribution Schematics: Under Accessory Wiring Junction Block


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 511
Chevrolet Venture V6-3.4L VIN E 1587

Power Distribution Schematics: Stop Lamp, Hazard, And PassKey Fuses, FRT HVAC MI BLWR And Headlamp Circuit Breakers
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 512
Chevrolet Venture V6-3.4L VIN E 1588

Power Distribution Schematics: IGN, SIR, T/S/G, Cruise, And PCM/PassKey 1 Cluster Fuses
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 513
Chevrolet Venture V6-3.4L VIN E 1589

Power Distribution Schematics: Ignition Switch IGN Main Relay, IGN Main 1, PCM/ABS, CONVENT SOL, DRL, And PCM/Crank Fuses
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 514
Chevrolet Venture V6-3.4L VIN E 1590

Power Distribution Schematics: IGN, SIR, T/S/G, Cruise, And PCM/PassKey 1 Cluster Fuses
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 515
Chevrolet Venture V6-3.4L VIN E 1591

Power Distribution Schematics: Ignition Switch IGN Main Relay, IGN Main 1, PCM/ABS, CONVENT SOL, DRL, And PCM/Crank Fuses
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 516
Chevrolet Venture V6-3.4L VIN E 1592

Power Distribution Schematics: IGN, SIR, T/S/G, Cruise, And PCM/PassKey 1 Cluster Fuses
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 517
Chevrolet Venture V6-3.4L VIN E 1593

stribution Schematics: Cluster BATT, RR PWR SCKT, PWR Lock, Rap Relay, CTSY Lamp, FRT PWR SCKT, Cigar/DLC And PWR Mir
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 518
Chevrolet Venture V6-3.4L VIN E 1594

stribution Schematics: Cluster BATT, RR PWR SCKT, PWR Lock, Rap Relay, CTSY Lamp, FRT PWR SCKT, Cigar/DLC And PWR Mir
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 519
Chevrolet Venture V6-3.4L VIN E 1595

Power Distribution Schematics: Underhood Accessory Wiring Junction Block, Relay Center, PWR WDO And PWR OTR Vent Fuses
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 520
Chevrolet Venture V6-3.4L VIN E 1596

Power Distribution Schematics: Underhood Accessory Wiring Junction Block, Relay Center, PWR WDO And PWR OTR Vent Fuses
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 521
Chevrolet Venture V6-3.4L VIN E 1597

Power Distribution Schematics: Underhood Accessory Wiring Junction Block, Relay Center, PWR WDO And PWR OTR Vent Fuses
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 522
Chevrolet Venture V6-3.4L VIN E 1598

stribution Schematics: (Export Only) LH T/LP, RH T/LP, LH HEAD LP High, RH HEAD LP High, LH Head LP Low, And RH Head LP L
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 523
Chevrolet Venture V6-3.4L VIN E 1599

bution Schematics: BATT Main 2, Headlamps, ELC/Trailer, RR Defog/HTP Mirrors And RR Fog LP Fuses And PWR/Heated Seat PSD Cir
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 524
Chevrolet Venture V6-3.4L VIN E 1600

bution Schematics: BATT Main 2, Headlamps, ELC/Trailer, RR Defog/HTP Mirrors And RR Fog LP Fuses And PWR/Heated Seat PSD Cir
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 525
Chevrolet Venture V6-3.4L VIN E 1601

Power Distribution Schematics: Stop Lamp, Hazard, And PassKey Fuses, FRT HVAC MI BLWR And Headlamp Circuit Breakers
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 526
Chevrolet Venture V6-3.4L VIN E 1602

Power Distribution Schematics: HVAC/DIC/DRL/Heated Seat, HVAC Blower And RR HVAC/TEMP CONT Fuses
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 527
Chevrolet Venture V6-3.4L VIN E 1603

stribution Schematics: Cluster BATT, RR PWR SCKT, PWR Lock, Rap Relay, CTSY Lamp, FRT PWR SCKT, Cigar/DLC And PWR Mir
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 528
Chevrolet Venture V6-3.4L VIN E 1604

Cigar Lighter/Auxiliary Outlets Schematics


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 529
Chevrolet Venture V6-3.4L VIN E 1605

ower Distribution Schematics: Ignition Switch, IGN Main 2, BCM PRORM, RR WPR/WSHR, MALL/Cluster And FRT/WPR/WSHR Fuse
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 530
Chevrolet Venture V6-3.4L VIN E 1606

Power Distribution Schematics: IGN, SIR, T/S/G, Cruise, And PCM/PassKey 1 Cluster Fuses
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 531
Chevrolet Venture V6-3.4L VIN E 1607

Power Distribution Schematics: IGN, SIR, T/S/G, Cruise, And PCM/PassKey 1 Cluster Fuses
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 532
Chevrolet Venture V6-3.4L VIN E 1608

Power Distribution Schematics: Stop Lamp, Hazard, And PassKey Fuses, FRT HVAC MI BLWR And Headlamp Circuit Breakers
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 533
Chevrolet Venture V6-3.4L VIN E 1609

Power Distribution Schematics: SWC Backlight And HTO Mirror Fuses


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 534
Chevrolet Venture V6-3.4L VIN E 1610

Power Distribution Schematics: Underhood Accessory Wiring Junction Block


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 535
Chevrolet Venture V6-3.4L VIN E 1611

Power Distribution Schematics: Stop Lamp, Hazard, And PassKey Fuses, FRT HVAC MI BLWR And Headlamp Circuit Breakers
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 536
Chevrolet Venture V6-3.4L VIN E 1612

Power Distribution Schematics: HVAC/DIC/DRL/Heated Seat, HVAC Blower And RR HVAC/TEMP CONT Fuses
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 537
Chevrolet Venture V6-3.4L VIN E 1613

ower Distribution Schematics: Ignition Switch, IGN Main 2, BCM PRORM, RR WPR/WSHR, MALL/Cluster And FRT/WPR/WSHR Fuse
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 538
Chevrolet Venture V6-3.4L VIN E 1614

Power Distribution Schematics: Ignition Switch IGN Main Relay, IGN Main 1, PCM/ABS, CONVENT SOL, DRL, And PCM/Crank Fuses
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 539
Chevrolet Venture V6-3.4L VIN E 1615

Power Distribution Schematics: Underhood Accessory Wiring Junction Block, Relay Center, PWR WDO And PWR OTR Vent Fuses
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 540
Chevrolet Venture V6-3.4L VIN E 1616

Ground Distribution Schematics: G401


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 541
Chevrolet Venture V6-3.4L VIN E 1617

Power Distribution Schematics: IGN, SIR, T/S/G, Cruise, And PCM/PassKey 1 Cluster Fuses
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 542
Chevrolet Venture V6-3.4L VIN E 1618

Ground Distribution Schematics: G200


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 543
Chevrolet Venture V6-3.4L VIN E 1619

Power Distribution Schematics: Underhood Accessory Wiring Junction Block


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 544
Chevrolet Venture V6-3.4L VIN E 1620

Power Distribution Schematics: Underhood Accessory Wiring Junction Block


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 545
Chevrolet Venture V6-3.4L VIN E 1621

Power Distribution Schematics: Underhood Accessory Wiring Junction Block


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 546
Chevrolet Venture V6-3.4L VIN E 1622

Power Distribution Schematics: Underhood Accessory Wiring Junction Block


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 547
Chevrolet Venture V6-3.4L VIN E 1623

Power Distribution Schematics: Underhood Accessory Wiring Junction Block


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 548
Chevrolet Venture V6-3.4L VIN E 1624

Power Distribution Schematics: Underhood Accessory Wiring Junction Block


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 549
Chevrolet Venture V6-3.4L VIN E 1625

Power Distribution Schematics: Underhood Accessory Wiring Junction Block


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 550
Chevrolet Venture V6-3.4L VIN E 1626

Power Distribution Schematics: Ignition Switch IGN Main Relay, IGN Main 1, PCM/ABS, CONVENT SOL, DRL, And PCM/Crank Fuses
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 551
Chevrolet Venture V6-3.4L VIN E 1627

stribution Schematics: Cluster BATT, RR PWR SCKT, PWR Lock, Rap Relay, CTSY Lamp, FRT PWR SCKT, Cigar/DLC And PWR Mir
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 552
Chevrolet Venture V6-3.4L VIN E 1628

Power Distribution Schematics: EBCM, BATT Main 1 And Radio Fuses


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 553
Chevrolet Venture V6-3.4L VIN E 1629

bution Schematics: BATT Main 2, Headlamps, ELC/Trailer, RR Defog/HTP Mirrors And RR Fog LP Fuses And PWR/Heated Seat PSD Cir
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 554
Chevrolet Venture V6-3.4L VIN E 1630

Power Distribution Schematics: EBCM, BATT Main 1 And Radio Fuses


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 555
Chevrolet Venture V6-3.4L VIN E 1631

Power Distribution Schematics: Underhood Accessory Wiring Junction Block, Relay Center, PWR WDO And PWR OTR Vent Fuses
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 556
Chevrolet Venture V6-3.4L VIN E 1632

Ground Distribution Schematics: G100, G111 And G113


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 557
Chevrolet Venture V6-3.4L VIN E 1633

Ground Distribution Schematics: G101 And G102


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 558
Chevrolet Venture V6-3.4L VIN E 1634

Ground Distribution Schematics: G101 And G102


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 559
Chevrolet Venture V6-3.4L VIN E 1635

Ground Distribution Schematics: G100, G111 And G113


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 560
Chevrolet Venture V6-3.4L VIN E 1636

Ground Distribution Schematics: G100, G111 And G113


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 561
Chevrolet Venture V6-3.4L VIN E 1637

Ground Distribution Schematics: G117


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 562
Chevrolet Venture V6-3.4L VIN E 1638

Ground Distribution Schematics: G200


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 563
Chevrolet Venture V6-3.4L VIN E 1639

Ground Distribution Schematics: G200


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 564
Chevrolet Venture V6-3.4L VIN E 1640

Ground Distribution Schematics: G200


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 565
Chevrolet Venture V6-3.4L VIN E 1641

Ground Distribution Schematics: G200 And G201


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 566
Chevrolet Venture V6-3.4L VIN E 1642

Ground Distribution Schematics: G200 And G201


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 567
Chevrolet Venture V6-3.4L VIN E 1643

Ground Distribution Schematics: G210


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 568
Chevrolet Venture V6-3.4L VIN E 1644

Ground Distribution Schematics: G301


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 569
Chevrolet Venture V6-3.4L VIN E 1645

Ground Distribution Schematics: G302


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 570
Chevrolet Venture V6-3.4L VIN E 1646

Ground Distribution Schematics: G302


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 571
Chevrolet Venture V6-3.4L VIN E 1647

Ground Distribution Schematics: G401


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 572
Chevrolet Venture V6-3.4L VIN E 1648

Ground Distribution Schematics: G401 And G402


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 573
Chevrolet Venture V6-3.4L VIN E 1649

Ground Distribution Schematics: G401 And G402

System Diagram
For information regarding diagrams refer to Starting and Charging diagrams.
See: Starting and Charging/Diagrams/Electrical Diagrams
Alternator
For information regarding diagrams for this system, please refer to Starting and Charging diagrams. See: Starting and Charging/Diagrams/Electrical
Diagrams
System Diagram
For information regarding diagrams for this system, please refer to Starting and Charging diagrams. See: Starting and Charging/Diagrams/Electrical
Diagrams
Starter Motor
For information regarding diagrams refer to Starting and Charging diagrams.
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 574
Chevrolet Venture V6-3.4L VIN E 1650
See: Starting and Charging/Diagrams/Electrical Diagrams

Steering Wheel Controls Schematics


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 575
Chevrolet Venture V6-3.4L VIN E 1651

Automatic Level Control Suspension Schematics: With Inflator


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 576
Chevrolet Venture V6-3.4L VIN E 1652

Automatic Level Control Suspension Schematics: Without Inflator


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 577
Chevrolet Venture V6-3.4L VIN E 1653
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 578
Chevrolet Venture V6-3.4L VIN E 1654
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 579
Chevrolet Venture V6-3.4L VIN E 1655
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 580
Chevrolet Venture V6-3.4L VIN E 1656
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 581
Chevrolet Venture V6-3.4L VIN E 1657
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 582
Chevrolet Venture V6-3.4L VIN E 1658
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 583
Chevrolet Venture V6-3.4L VIN E 1659

Body Rear End Schematics: IP REAR HATCH AJAR Telltale


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 584
Chevrolet Venture V6-3.4L VIN E 1660

Power Window Schematics


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 585
Chevrolet Venture V6-3.4L VIN E 1661

Body Rear End Schematics: Rear Quarter Windows


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 586
Chevrolet Venture V6-3.4L VIN E 1662

Wiper/Washer System: Pulse Schematics


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 587
Chevrolet Venture V6-3.4L VIN E 1663

Wiper/Washer System (Rear) Schematics


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 588
Chevrolet Venture V6-3.4L VIN E 1664

Wiper/Washer System: Pulse Schematics


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 589
Chevrolet Venture V6-3.4L VIN E 1665

Wiper/Washer System (Rear) Schematics


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 590
Chevrolet Venture V6-3.4L VIN E 1666

Wiper/Washer System: Pulse Schematics


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 591
Chevrolet Venture V6-3.4L VIN E 1667

Wiper/Washer System (Rear) Schematics


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 592
Chevrolet Venture V6-3.4L VIN E 1668

Wiper/Washer System: Pulse Schematics


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 593
Chevrolet Venture V6-3.4L VIN E 1669

Wiper/Washer System (Rear) Schematics


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 594
Chevrolet Venture V6-3.4L VIN E 1670

Wiper/Washer System: Pulse Schematics


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 595
Chevrolet Venture V6-3.4L VIN E 1671

Wiper/Washer System (Rear) Schematics

Drive Belt
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 596
Chevrolet Venture V6-3.4L VIN E 1672

Timing Chain

- Align the crankshaft timing mark (2) to the timing mark on the bottom of the timing chain dampener (1).
- Align the timing mark on the camshaft gear (4) with the timing mark on top of the timing chain dampener (3).
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 597
Chevrolet Venture V6-3.4L VIN E 1673

Schematic
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 598
Chevrolet Venture V6-3.4L VIN E 1674

Schematic
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 599
Chevrolet Venture V6-3.4L VIN E 1675

Schematic
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 600
Chevrolet Venture V6-3.4L VIN E 1676

Schematic

Engine Lubrication
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 601
Chevrolet Venture V6-3.4L VIN E 1677

Front View

Rear View
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 602
Chevrolet Venture V6-3.4L VIN E 1678

Right View
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 603
Chevrolet Venture V6-3.4L VIN E 1679

Locations View
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 604
Chevrolet Venture V6-3.4L VIN E 1680

Locations View
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 1
Chevrolet Venture V6-3.4L VIN E 1681
Computers and Control Systems: Testing and Inspection

Checking the Basics


DIAGNOSTIC NOTES
Diagnosing problems in modern automobiles can sometimes be very frustrating and confusing, especially when it involves computer controlled
systems. The fact is, for the most part automotive electronics have been proven quite reliable, and the greatest number of problems with new cars
are the same kinds of problems that older cars without computer controls have.

Before suspecting a computer problem, perform a careful visual inspection. Check under the hood for the same kinds of problems you would
look for on a non-computer controlled engine. These include fluid leaks, vacuum leaks, dirty filters, overheating, oil burning, poor connections
or loose wires, bad spark plug wires and/or spark plugs, restricted mufflers and exhaust systems, worn mechanical parts, exhaust leaks, and other
familiar kinds of problems. Be thorough! You may save a lot of time.

Begin all troubleshooting by Checking the Basics. Certain basic faults may be undetectable by the Powertrain Control Module (PCM)
self-diagnostic system and can actually interfere with self-checking and fault memory operation. Low battery voltage, for example, can cause
erroneous faults to set in PCM memory or can cause a system to go "Fail Safe" without setting a fault in memory. Because system fault memory
is cleared whenever PCM or battery are disconnected, fault codes should be read prior to any vehicle power interruption or troubleshooting. Prior
to any teardown, repair or component replacement, consider the following steps:

COMPLAINT VERIFICATION
Whenever possible, the technicians should personally verify the complaint. Having experienced the malfunction, technicians are less likely to
attempt repairing non-existent faults.

MALFUNCTION VERIFICATION
Sophisticated automotive systems are easily misunderstood. This can lead to repairs that attempt to force a system to perform as it was never
intended. The troubleshooting technician should compare actual system operation to nominal system operation as described in Description and
Operation. The technician is also encouraged to compare problem vehicle system operation with a known good vehicle.

PREVIOUS REPAIRS
Vehicle repair history can provide explanations to unusual complaints which seem to elude normal troubleshooting attempts. Incorrect
components or unapproved repairs can have subtle influences on seemingly unrelated systems.

BATTERY STATE OF CHARGE


Batteries in a state of partial discharge can have a dramatic effect on the PCM and related electrical components.

POSITIVE BATTERY CABLE INTEGRITY


All B+ connections must be in perfect condition for trouble-free electronic system operation.

FUSIBLE LINK INTEGRITY


Fusible links prevent possible damage to electrical components and wiring harnesses. These links and their connections must be without dynamic
resistance. Dynamic resistance can only be checked using the voltage drop method of testing.

NEGATIVE GROUND CONNECTIONS


All B- connections must be checked and verified to be in perfect condition. A poor "common" ground point will cause seemingly unrelated
systems to influence one another. High current systems which encounter a poor "common" ground can back feed through other electrical
systems, causing unusual operation and inexplicable component failure. Electrical system ground side should be checked dynamically using the
voltage drop technique.

POWERTRAIN CABLE ATTACHMENTS


Metal cables attached to engine or transmission which appear overheated and/or discolored indicate the need to thoroughly test all ground
connections.

POWER SUPPLY RELAYS


Fuel pump and main relays, as well as their plug connections, can be a source of intermittent operation which will not set a code in PCM fault
memory.

HIGH TENSION COIL AND SECONDARY COMPONENTS WIRING


Secondary ignition system should be checked visibly as well as with a suitable engine analyzer and scope. Check components for tight
connections and freedom from carbon tracking, moisture and corrosion.

FUEL DELIVERY AND FUEL RAIL PRESSURE


Fuel delivery must begin at once when cranking and pressure in the fuel rails must be within specifications. Fuel pressure must be maintained
between fuel pump outlet and pressure regulator after engine shutdown.

SPARK PLUG CLEARANCE


Spark plug gap, if out of specification, can significantly impair engine performance. Verify spark plug type, condition, and gap according to
specification.

VACUUM AND VAPOR HOSE INTEGRITY


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 2
Chevrolet Venture V6-3.4L VIN E 1682
Vacuum and vapor hoses must be routed correctly and not leaking. Always use the underhood label for primary information.

AIR/FUEL RATIO
Adaptive engine management systems efficiently compensate for conditions which may affect the combustion process. However, when
troubleshooting idle quality or driveability complaints, it is still necessary to consider the following:
- Injector spray pattern quality
- Presence of unmetered air leaks
- Evaporative purge system
- Excessive engine oil dilution
- Substandard fuel or unapproved additives
- Carbon build-up

TESTING EQUIPMENT
High quality testing equipment is essential for accurate results. Faulty equipment results in erroneous test results. Use only suitable test leads,
terminals, and probe tips.

Diagnostic Starting Point


Begin the system diagnosis with A Powertrain On Board Diagnostic (OBD) System Check. The Powertrain OBD System Check provides the
following information: See: Initial Inspection and Diagnostic Overview
- The identification of the control modules which command the system.
- The ability of the control modules to communicate through the serial data circuit.
- The identification of any stored Diagnostic Trouble Codes (DTCs) and their status.

The use of the Powertrain OBD System Check identifies the correct procedure for diagnosing the system and where the procedure is located.

Intermittent Conditions (Part 1 Of 3)


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 3
Chevrolet Venture V6-3.4L VIN E 1683

Intermittent Conditions (Part 2 Of 3)


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 4
Chevrolet Venture V6-3.4L VIN E 1684

Intermittent Conditions (Part 3 Of 3)

Basic Electrical Circuits


You should understand basic electricity and know the meaning of voltage (volts), current (amps), and resistance (ohms). You should understand
what happens in a circuit with an open or a shorted wire and you should be able to identify a shorted or open circuit using a DMM.

Conditions For Running The DTC


The running conditions (enabling conditions) are the conditions that must be met before the PCM will test the sensor/system. These conditions are
generally set up so that the sensor/system may be reliably tested without a false failure indication.

Conditions For Setting The DTC


The setting conditions are the conditions that must be met for the DTC to set. A sensor/system is tested only after the running conditions are met. If
the enabling conditions are met, and the PCM detects an abnormal sensor/system condition, the appropriate DTC is set.

Diagnosing Intermittents
Diagnosing intermittent conditions can be difficult. The conditions that set the DTC set may not be present. This does not mean that the problem is
fixed. The problem may return in the future intermittently. So, it at all possible, the problem should be diagnosed, and repaired. The only way to
diagnose an intermittent condition is to gather information from the time when the DTC was set. This can be done in 2 ways through snapshot data
and driver observations. For further information refer to Scan Tool Snapshot Procedure.

Diagnostic Procedure Use


The diagnostic procedures used in this section are designed to find and repair powertrain related problems. The general approach is to find the
appropriate diagnosis for a problem with 5 basic steps described below.
1. Do you understand the customers complaint? The technician must understand what the customers complaint is. Failure to understand this
may lead to misdiagnosis, or unnecessary diagnosis. Among other things, the technician must know whether the condition is present at all
times, only under certain circumstances, or truly intermittent (random). This will assist the technician in duplicating and diagnosing the
problem. Another reason the technician must understand the customers complaint is so the technician may determine whether the complaint
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 5
Chevrolet Venture V6-3.4L VIN E 1685
requires service or is normal vehicle operation. Trying to diagnose a complaint that is normal will waste time and may result in unnecessary
service.
2. Are Diagnostics working properly? Use the Powertrain On Board Diagnostic (OBD) System Check. This is the starting point for the
diagnostic procedure, always begin here.
3. Are DTCs displayed? If a DTC is identified by diagnostics, the Powertrain On Board Diagnostic (OBD) System Check will direct you to the
appropriate table.
4. Is the customers complaint related to a specific powertrain subsystem? If no related DTCs are set, the next quickest way to locate the problem
is to narrow the problem down to a specific powertrain subsystem. If a specific subsystem can be pinpointed as the cause, the problem is
easier to diagnose.
5. Is the problem powertrain related? Some customer complaints may appear to be powertrain related but are actually caused by other vehicle
systems.

Powertrain OBD System Check

IMPORTANT: Understanding and using the table correctly will reduce diagnostic time, and prevent the unnecessary replacement of parts.

After the visual/physical inspection is complete, the Powertrain On Board Diagnostic (OBD) System Check should be performed. The OBD System
Check will provide direction to diagnose the following conditions.

- PCM inoperative or damaged


- No PCM data
- MIL inoperative
- PCM DTCs
- Fuel System Rich or Lean
- Customer Complaint Driveability Symptoms

The Powertrain On Board Diagnostic (OBD) System Check is designed as a Master table for driveability and emissions system diagnosis. The
Powertrain On Board Diagnostic (OBD) System Check should always be used as the starting point for all Powertrain diagnosis.

The Powertrain On Board Diagnostic (OBD) System Check is an organized approach for identifying a problem. Driver Comments normally fall
into one of the following areas:
- Steady SERVICE ENGINE SOON MIL
- Driveability problem
- Engine will not start or stalls after start

Circuit Diagram
The circuit diagram of the diagnostic support information page will show the circuits and components involved in setting the DTC. This diagram
may be used as a reference when circuit tests are required in the table. If there is only a reference to a circuit diagram, or more detailed circuit
information is required, the Engine Controls Schematics may be referenced.

Using Diagnostic Trouble Code (DTC) Tables


When diagnosing this powertrain, you will almost certainly need to use the diagnostic procedures. The diagnostic procedures are mostly in the form
of tables. At the beginning of each DTC will be a circuit diagram, or a reference to a circuit diagram, a circuit description and notes about the
condition or DTC diagnosed in the table. Reading the diagnostic support Information will help you understand the system being tested, the
components involved in the testing, how the PCM tests the system (enabling conditions), how the PCM determines that the diagnostic has failed
(conditions for setting the DTC), and what the table is trying to accomplish. Below are explanations of the diagnostic support information and
tables for DTCs.

Action Taken When the DTC Sets


The actions taken are the steps the PCM takes after the DTC is set. These actions serve one of three purposes:
- To inform the driver of the problem
- To preserve the driveability of the vehicle
- To prevent the failure from causing any damage to the vehicle
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 6
Chevrolet Venture V6-3.4L VIN E 1686
Circuit Description
The circuit description explains the sensor and/or circuits involved in setting the DTC, and gives a brief description of when the DTC is set.

Conditions For Clearing the MIL/DTC


These are the conditions that must be met to turn OFF the MIL, and/or clear the DTC.

Diagnostic Aids
Diagnostic Aids provide helpful information when the conditions that caused the DTC or driveability problem is not currently present. Sometimes,
with the help of snapshot on DTC set data (Freeze Frame or Failure Records) or information from the driver, the problem may still be identified or
at least narrowed down to a short list of possible intermittent conditions. When this is true, the Diagnostic Aids may explain what to look for, and
the most logical path to locate an intermittent condition.

Test Description
The Test Descriptions are explanations of the reason certain tests are done, and what the test is supposed to uncover. The information is numbered
according to the corresponding step in the diagnostic table. When questions of why a certain step is performed, or what results the step should
actually produce, observe the step number next to the test you are performing. Refer to the information under Test Description that has the same
number for an explanation.

Diagnostic Table
Diagnostic tables are an organized and systematic approach to diagnosing a Diagnostic Trouble Code (DTC). The table consists of five separate
columns: step number, action, value, yes, and no. The step number indicates which step is being performed. The action column contains all
necessary information about how to perform a certain test. The last sentence in each action block will always be a question. The question can only
be answered yes or no. The answer to the question will dictate which column you will go to next - yes or no. The yes or no answer to each test will
lead to the next logical step within the diagnostic table. Most or the YES and NO boxes will take you to the next logical step within the table.
However, some boxes may lead to other system diagnostics, or to the Diagnostic Aids when an intermittent condition exists.

Always begin with Step 1 at the top of the table unless there is a notice or caution above the first step. Never skip steps or jump ahead in the table
unless specified by the Yes/No columns. Taking short cuts often leads to misdiagnosis. When a problem is found, make the necessary repairs, and
then verify the repair.

Testing Terminal Contact


Many tables will have you testing terminal contact before replacing a component. This is done because the tests performed in tables can only test
the continuity of a circuit across a wire or in-line connection, not the continuity across the connection at a component. Testing terminal contact will
prevent the replacement of good components, prevent comebacks due to intermittent connection problems, and make some repair jobs easier, as in
replacing a terminal instead of a component. For this reason you must test terminal contact when instructed to do so.

Testing terminal contact is easy as long as you have a supply of new terminals handy. The J 38125-B Terminal Repair Kit, is a good source of
terminals for testing terminal contact. This repair kit contains a supply of all currently used terminal series. To test terminal contact, start by
inspecting the male terminals. They should be straight and aligned with other terminals in the row. They should not be twisted, bent or otherwise
damaged. The female terminal should be, likewise, inspected for alignment and damage. Finally, connect a new male terminal of the same series
(e.g., Metri-pack 150, Weatherpack, etc.) to the female terminals to be tested. The terminal should not fall out or be easily jarred out of connection.
The terminal should require some force to become disconnected. The force required to disconnect the terminal will depend on the size of the
terminal being tested. Larger terminals, Metri-pack series for example, should be very difficult to remove by hand. Smaller terminals, Micro-pack
series for example, should be easier to disconnect by hand but still should not fall out. Replace, do not repair, any damaged terminals.

Use of Digital Multimeter (DMM)


You should be familiar with the DMM. You should be able to use the meter to measure voltage (volts), resistance (ohms), current (amps),
capacitance (farads), intermittent (min/max) and frequency (Hertz).

Scan Tool Data List


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 7
Chevrolet Venture V6-3.4L VIN E 1687

Scan Tool Data List (Part 1 Of 4)


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 8
Chevrolet Venture V6-3.4L VIN E 1688

Scan Tool Data List (Part 2 Of 4)


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 9
Chevrolet Venture V6-3.4L VIN E 1689

Scan Tool Data List (Part 3 Of 4)


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 10
Chevrolet Venture V6-3.4L VIN E 1690

Scan Tool Data List (Part 4 Of 4)

Use the Typical Scan Data Values table only after the Diagnostic System Check - Computers and Control Systems has been completed, no DTCs
were noted and you have determined the on-board diagnostics are functioning properly. Scan tool values from a properly running engine may be
used for comparison with the engine you are diagnosing. The Typical Scan Data values represent values that would be seen on a normally running
engine.

IMPORTANT: A scan tool that displays faulty data should not be used, and the problem should be reported to the scan tool manufacturer. Use of
a faulty scan tool can result in misdiagnosis and unnecessary parts replacement.

Only the parameters listed below are referred to in this service manual for use in diagnosis. For further information on using the scan tool to
diagnose the Powertrain Control Module (PCM) and related sensors, refer to the applicable reference section listed below. If all values are within
the typical range described below, refer to Symptoms - Computers and Control Systems. The Typical Scan Data Values table contains all the
parameters included in the following data lists arranged in alphabetical order: See: Symptom Related Diagnostic Procedures
- Engine Data 1-Contains general information regarding fuel delivery, idle air control (IAC) position, Heated Oxygen Sensor (HO2S 1),
HO2S 2, and other basic engine operating conditions.
- Engine Data 2-Contains general information regarding Engine Coolant Temperature (ECT), Intake Air Temperature (IAT), Mass Air Flow (
MAF), Manifold Absolute Pressure (MAP) and other basic engine operating conditions.
- EGR Data-Contains information specific to the Exhaust Gas Recirculation (EGR) system. This list displays parameters required to verify
proper EGR system operation
- EVAP Data-Contains information specific to the Evaporative Emissions (EVAP) control system. Also displays parameters required to verify
proper EVAP system operation.
- Fuel Trim Data-Contains information specific to the fuel trim operation. Also displays parameters required to verify proper fuel trim
operation.
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 11
Chevrolet Venture V6-3.4L VIN E 1691
- Misfire Data-Contains information specific to the misfire diagnostics and parameters required to verify proper operation with regard to
misfire.
- Output Driver Data-Contains information specific to output driver circuits. This data monitors circuit status, and circuit history.

For scan tool parameter definitions, refer to Scan Tool Data Definitions. See: Scan Tool Testing and Procedures

IMPORTANT: Use the Typical Scan Data Values only after the following conditions are met:
- The Diagnostic System Check - Computers and Control Systems has been completed.
- The engine is idling unless checking a value at a specified RPM.
- The throttle is closed unless checking a value at a specified RPM.
- The vehicle is in PARK or NEUTRAL.
- The vehicle is operating in Closed Loop.
- The vehicle accessories are turned OFF.

Class II Serial Data


The Class II serial data circuit allows the control modules to communicate with each other. The modules send a series of digital signals pulsed from
approximately 7 volts to 0 volts. These signals are sent in variable pulse widths of one or 2 bits. A string of these bits creates a message that is sent
in a prioritized data packet. This allows more than one module to send messages at the same time without overloading the serial data line. The
speed, or baud rate, at which the control modules communicate depends on the message content. Large message content lowers the baud rate, while
small message content increases the baud rate. The average baud rate is approximately 10.4 Kbps (10,400 bits per second). When the key is ON,
each module sends a State Of Health (SOH) message to the other control modules using the Class II serial data line. This ensures that the modules
are working properly. When the module stops communicating, a loss of the SOH message occurs. The control modules that should receive the
message detect the loss and set a loss of communication DTC.
Service Engine Soon/Malfunction Indicator Lamp (MIL)
The Service Engine Soon/Malfunction Indicator Lamp (MIL) is located in the Instrument Panel (IP) Cluster. The MIL is controlled by the PCM
and is used to indicate that the PCM has detected a condition that affects vehicle emissions, may cause powertrain damage, or severely impacts
driveability.
MIL Operation
The Malfunction Indicator Lamp (MIL) is located on the instrument panel and is displayed as CHECK ENGINE lamp.

MIL Operation
- The MIL informs the driver that a malfunction has occurred and the vehicle should be taken in for service as soon as possible
- The MIL illuminates during a bulb test and a system test
- A DTC will be stored if a MIL is requested by the diagnostic

MIL Illumination
- The MIL will illuminate with ignition switch ON and the engine not running
- The MIL will turn OFF when the engine is started
- The MIL will remain ON if the self-diagnostic system has detected a malfunction
- The MIL may turn OFF if the malfunction is not present
- If the MIL is illuminated and then the engine stalls, the MIL will remain illuminated so long as the ignition switch is ON.
- If the MIL is not illuminated and the engine stalls, the MIL will not illuminate until the ignition switch is cycled OFF, then ON.
Trip
A trip is an interval of time during which the diagnostic test runs. A trip may consist of only a key cycle to power up the PCM, allow the diagnostic
to run, then cycle the key off to power down the PCM. A trip may also involve a PCM power up, meeting specific conditions to run the diagnostic
test, then powering down the PCM. The definition of a trip depends upon the diagnostic. Some diagnostic tests run only once per trip (i.e., catalyst
monitor) while other tests run continuously during each trip (i.e., misfire, fuel system monitors).
Warm-Up Cycle
The PCM uses warm-up cycles to run some diagnostics, and to clear any Diagnostic Trouble Codes (DTCs). A warm-up cycle occurs when the
engine coolant temperature increases 22°C (40°F) from start-up. The engine coolant must also achieve a minimum temperature of 71°C (160°F).
The PCM counts the number of warm-up cycles in order to clear the Malfunction Indicator Lamp (MIL). The PCM will clear the DTCs when 40
consecutive warm-up cycles occur without a malfunction.

Diagnostic Trouble Code Display


DTCs can only be displayed with the use of a scan tool.
Diagnostic Trouble Codes (DTCs)
The PCM is programmed with test routines that test the operation of the various systems the PCM controls. Some tests monitor internal PCM
functions. Many tests are run continuously. Other tests run only under specific conditions, referred to as Conditions for Running the DTC. When
the vehicle is operating within the conditions for running a particular test, the PCM monitors certain parameters and determines whether or not the
values are within an expected range.

The parameters and values considered outside the range of normal operation are listed as Conditions for Setting the DTC. When the Conditions for
Setting the DTC occur, the PCM executes the Action Taken When the DTC Sets. Some DTCs alert the driver via the MIL or a message. Other
DTCs do not trigger a driver warning, but are stored in memory. Refer to the Diagnostic Trouble Code (DTC) List/Type for a complete list of PCM
DTCs and the driver alerts the DTCs trigger. The PCM also saves data and input parameters when most DTCs are set. This data is stored in the
Freeze Frame and/or Failure Records.
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 12
Chevrolet Venture V6-3.4L VIN E 1692

DTCs are categorized by type. The DTC type is determined by the MIL operation and the manner in which the fault data is stored when a particular
DTC fails. In some cases there may be exceptions to this structure. Therefore, it is important to read the Action Taken When the DTC Sets and the
Conditions for Clearing the MIL/DTC in the supporting text when diagnosing the system.

There are different types of DTCs and the action they take when set. Refer to Diagnostic Trouble Code (DTC) Type Definitions for a description of
the general characteristics of each DTC type
Freeze Frame Data
Government regulations require that engine operating conditions be captured whenever the MIL is illuminated. The data captured is called Freeze
Frame data. The Freeze Frame data is very similar to a single record of operating conditions. Whenever the MIL is illuminated, the corresponding
record of operating conditions is recorded as Freeze Frame data. A subsequent failure will not update the recorded operating conditions.

The Freeze Frame data parameters stored with a DTC failure include the following:
- The air/fuel ratio
- The air flow rate
- The fuel trim
- The engine speed
- The engine load
- The engine coolant temperature
- The vehicle speed
- The Throttle Position (TP) angle
- The Manifold Absolute Pressure (MAP)/barometric pressure (BARO)
- The injector base pulse width
- The loop status

Freeze frame data can only be overwritten with data associated with a misfire or fuel trim malfunction. Data from these faults take precedence over
data associated with any other fault. The Freeze Frame data will not be erased unless the associated history DTC is cleared.
Failure Records Data
In addition to Freeze Frame data the PCM may also store Failure Records data when a DTC reports a failure. Unlike Freeze Frame data, Failure
Records data can be stored by DTC's that DO NOT illuminate the MIL.

The Freeze Frame/Failure Records data may be retrieved through the Diagnostic Trouble Code menu on scan tool. If more than one DTC is set,
review the odometer or engine run time data located in the Freeze Frame/Failure Records info to determine the most current failure.

Keep in mind that once Freeze Frame or Failure Record is selected, the parameter and input data displayed will look just like the normal PCM data
except the parameters will not vary since stored data is being displayed.

IMPORTANT: Always capture the Freeze Frame and Failure Records information with the scan tool BEFORE proceeding with diagnosis.
Clearing DTCs, disconnecting the battery, disconnecting the PCM or body connectors, or procedures performed during diagnosis may erase or
overwrite the stored Freeze Frame and Failure Records data. Loss of this data may prevent accurate diagnosis of an intermittent or difficult to set
DTC.
Capturing DTC Info (Capture Info)
Selecting this option on the scan tool allows the technician to record the Freeze Frame and Failure Records that may be stored in the PCM memory.
Capture DTC info before beginning diagnosis. This is a step in the OBD System Check. At the end of the diagnostic tables you are instructed to
clear DTCs, verify that the repair was successful, and then to review captured information. The captured information will contain any additional
DTCs and related data that was stored originally (if multiple DTCs were stored).

Selecting this option on the scan tool allows the technician to record the Freeze Frame and Failure Records that may be stored in the PCM memory.
This can be useful if the PCM or battery must be disconnected and later review of the stored information may be desired.
Storing and Erasing Freeze Frame Data
Government regulations require that engine operating conditions be captured whenever the MIL is illuminated. This data captured is called Freeze
Frame data. The Freeze Frame data is very similar to a single record of operating conditions. Whenever the MIL is illuminated, the corresponding
record of operating conditions is recorded to the Freeze Frame buffer.

Each time a diagnostic test reports a failure, the current engine operating conditions are recorded in the Freeze Frame buffer. A subsequent failure
will update the recorded operating conditions. The following operating conditions for the diagnostic test which failed typically include the
following parameters:
- The air/fuel ratio
- The air flow rate
- The fuel trim
- The engine speed
- The engine load
- The engine coolant temperature
- The vehicle speed
- The throttle position angle
- The manifold absolute pressure/barometric pressure
- The injector base pulse width
- The loop status
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 13
Chevrolet Venture V6-3.4L VIN E 1693

Freeze Frame data can only be overwritten with data associated with a misfire or fuel trim malfunction. Data from these faults take precedence over
data associated with any other fault. The Freeze Frame data will not be erased unless the associated history DTC is cleared.

Data Link Connector (DLC)


The provision for communicating with the control module is the Data Link Connector (DLC). The connector is usually located under the
instrument panel. The DLC is used to connect to a scan tool. Some common uses of the scan tool are listed below:
- Identifying stored Diagnostic Trouble Codes (DTCs).
- Clearing DTCs
- Performing output control tests.
- Reading serial data.

Clearing Diagnostic Trouble Codes


Use a scan tool to clear DTCs from the PCM memory. Disconnecting the vehicle battery to clear the PCM memory is not recommended. This may
or may not clear the PCM memory and other vehicle system memories will be cleared. Do not disconnect the PCM connectors solely for clearing
DTCs. This unnecessarily disturbs the connections and may introduce a new problem. Before clearing DTCs the scan tool has the capability to save
any data stored with the DTCs and then display that data at a later time. Capture DTC info before beginning diagnosis (refer to Capturing DTC
Info). Do not clear DTCs until you are instructed to do so within a diagnostic procedure.

Many PCM DTCs have complex test and failure conditions. Therefore, simply clearing DTCs and determining if the DTC sets again may not
indicate whether a problem has been corrected. To verify a repair after the repair is complete, you must look up the test conditions and duplicate
those conditions. If the DTC runs and passes, it is probable that the problem is fixed.
DTC Status
When the Scan tool displays a DTC, the status of the DTC is also displayed. The following DTC statuses are indicated only when they apply to the
DTC that is set.

Fail This Ign. (Fail This Ignition): Indicates that this DTC failed during the present ignition cycle.

Last Test Fail: Indicates that this DTC failed the last time the test ran. The last test may have run during a previous ignition cycle if an A or B type
DTC is displayed. For type C DTCs, the last failure must have occurred during the current ignition cycle to appear as Last Test Fail.

MIL Request: Indicates that this DTC is currently requesting the MIL. This selection will report type B DTCs only when they have requested the
MIL. (failed twice).

Test Fail SCC (Test Failed Since Code Clear): Indicates that this DTC that has reported a failure since the last time DTCs were cleared.

History: Indicates that the DTC is stored in the PCM History memory. Type B DTCs will not appear in History until they have requested the MIL
(failed twice). History will be displayed for all type A DTCs and type B DTCs (which have requested the MIL) that have failed within the last 40
warm-up cycles. Type C DTCs that have failed within the last 40 warm-up cycles will also appear in History.

Not Run SCC (Not Run Since Code Clear): DTCs will be listed in this category if the diagnostic has not run since DTCs were last cleared. This
status is not included with the DTC display since the DTC can not be set if the diagnostic has not run. This information is displayed when DTC Info
is requested using the scan tool.
Storing and Erasing Failure Records Data
When a PCM DTC sets, the PCM does several things. Among these is saving useful data and input parameter information for service diagnosis.
This information is referred to as Freeze Frame/Failure Records. You will see references to these in many PCM DTC diagnostic tables because this
information can be useful in pinpointing a problem even if the problem is not present when the vehicle is in the service bay.

Freeze Frame/Failure Records data may be retrieved through the DTC menu on scan tool. If more than one DTC is set review the odometer or
engine run time data located in the Freeze Frame/Failure Records info to determine the most current failure.

Keep in mind that once Freeze Frame or Failure Record is selected, the parameter and input data displayed will look just like the normal PCM data
except the parameters will not vary since stored data is being displayed.
PCM Snapshot Using A Scan Tool
The scan tool can be set up to take a "snapshot" of the parameters available via serial data. The Snapshot function records live data over a period of
time. The recorded data can be played back and analyzed. The scan tool can also graph parameters singly or in combinations of parameters for
comparison. The snapshot can be triggered manually at the time a symptom is noticed, or set up in advance to trigger when a DTC sets. An
abnormal value captured in the recorded data may point to a system or component that needs to be investigated further. The snapshot will remain in
the scan tool memory even after the tool is disconnected from it's power source. Refer to the scan tool user instructions for more information on the
Snapshot function.
General Information
This vehicle is equipped with an on-board diagnostic feature capable of performing the following functions:
- Feature Customization
- Displaying DTCs
- Clearing DTCs
- Input/Output Diagnostics
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 14
Chevrolet Venture V6-3.4L VIN E 1694
Entering Feature Customization Mode
The feature customization mode is used to configure the BCM to function in various applications. The BCM can be customized to change the
following vehicle functions:
- Interior Lighting Features
- Door Lock System
- Keyless Entry System
- Content Theft Deterrent System

In order to enter the feature customization mode perform the following steps:
1. Turn the ignition switch to the LOCK position.
2. Remove the BCM PRGRM fuse.
3. Turn the ignition switch to the ACC position. When entering the feature customization mode, the BCM first identifies what type of BCM is
installed on the vehicle by flashing the fasten seat belts indicator and sounds the chime 2, 3 or 4 times depending on the type of BCM used on
the vehicle. There are 3 different types of BCM that can be installed on the vehicle based on the vehicle option content that matches the BCM
capabilities. Ensure that the BCM installed on the vehicle is compatible with all of the features on the vehicle. Refer to Body Control System
circuit description for BCM identification. For more information on features that can be customized, refer to:
- Interior Lights Circuit Description
- Automatic Door Lock System Description
- Keyless Entry System Circuit Description
- Content Theft Deterrent (CTD) Circuit Description

Entering On-Board Diagnostic Mode


Complete the following steps in order to enter the diagnostics mode:
1. Turn the ignition switch to the LOCK position.
2. Remove the BCM PRGRM fuse.
3. Turn the ignition switch to the ACC position.
4. Turn the ignition switch from the ACC position to the LOCK position then back to the ACC position within 1 second.

The BCM will enter the on-board diagnostic mode and flash the fasten seat belts indicator and sound the chime equal to the number of DTCs stored
in the BCM memory. If no DTCs are stored, the BCM will not flash the fasten seat belts indicator or activate the chime.

The BCM flashes and sounds the first DTC with the lowest number, pauses, then continues with the next DTC until all of the DTCs are read. With
a DTC 1, the BCM will only sound the chime once, and the fasten seat belts indicator will not flash. Once all of the DTCs are read, the BCM
repeats this sequence 3 times.

IMPORTANT: If the fasten seat belts indicator does not flash, and the chime does not sound, complete the following procedure in order to
confirm that the BCM has entered the diagnostics mode:

1. Ensure that all of the vehicle doors are closed.


2. Open and close any vehicle door.
3. Fasten and release the driver seat belt.

The BCM sounds the chime when receiving an input signal such as opening a door or fastening the driver seat belt when the BCM is in the
diagnostics mode.

If the BCM does not sound the chime upon opening a door or fastening the driver seat belt, repeat Step 1 of Entering the Feature Customization
Mode. If the BCM does not enter the diagnostics mode, then refer to Body Control Module Inoperative.

Entering Input/Output Diagnostic Mode


After the BCM reads all of the DTCs in the memory, the BCM enters the Input/Output Diagnostic Mode. The BCM flashes the fasten seat belts
indicator and sounds the chime once when any of the following inputs are activated:
- Courtesy lamp switches
- Door lock cylinder switches
- Driver door ajar switch
- Driver fasten seat belt switch
- Driver Information Display (DID)
- Headlamp switch
- IP compartment lamp switch
- Keyless entry request for door lock/unlock
- Keyless entry request for the alarm (RPO UA6)
- Passenger door ajar switch
- Power door lock switches
- Liftgate ajar switch
- Sliding door ajar switch(es)
- Shock sensor
- Sunshade illuminated mirrors
- Hazard switch

Perform the following procedure in order to test the BCM outputs:


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 15
Chevrolet Venture V6-3.4L VIN E 1695
1. Ensure that the BCM is in the diagnostic mode. Refer to Entering On-Board Diagnostic Mode.
2. Cycle the interior light switch ON then OFF.
3. The BCM will enter the Output Diagnostic Test Mode 1.
4. Each cycle of the interior light switch (ON/OFF) will to select from following test modes depending on BCM type:
- Test Mode 1- De-activates the courtesy lights output and removes power to all of the interior lamps.
- Test Mode 2- Activates the courtesy lights output and provides power to all of the interior lamps (interior lamp override switch must be
ON).
- Test Mode 3- Activates the courtesy lights output and turns ON all of the courtesy lamps (interior lamp switch must be ON).
- Test Mode 4- Activates the theft deterrent relay for 1 second and turns ON the headlamps (BCM type 4).
- Test Mode 5- Energizes the horn relay for 25 ms (BCM type 4).
- Test Mode 6- Turns on the security LED indicator (BCM type 4).
- Test Mode 7- Turns off the security LED indicator (BCM type 4).

When the BCM completes all test modes, the BCM will repeat the test mode sequence.

Exiting Diagnostics
Perform the following procedure in order to exit the BCM diagnostics mode and return to normal BCM operation:
1. Turn the ignition switch to the LOCK position.
2. Reinstall the BCM PRGRM fuse.
3. Turn the ignition switch to the RUN position.

For a description of the RPO Code(s) shown in this article, refer to the RPO Code List found at Vehicle/Application and ID. See: Application and
ID
Diagnostic Trouble Code (DTC) Displaying
1. Ensure that the BCM is in the feature customization mode. Refer to On-Board Diagnostic Features.
2. Turn the ignition switch from the ACC position to the LOCK position then back to the ACC position within 1 second.

The BCM will enter the on-board diagnostic mode and flash the fasten seat belts indicator and sound the chime equal to the number of DTCs stored
in the BCM memory. If no DTCs are stored, the BCM will not flash the fasten seat belts indicator or activate the chime.

The BCM flashes and sounds the first DTC with the lowest number, pauses, then continues with the next DTC until all of the DTCs are read. With
a DTC 1, the BCM will only sound the chime once, and the fasten seat belts indicator will not flash. Once all of the DTCs are read, the BCM
repeats this sequence 3 times.

Diagnostic Trouble Code (DTC) Clearing


CLEARING DTCS
BCM DTCs can only be cleared by completing the following procedure:
1. Enter the BCM on-board diagnostic mode. Refer to On-Board Diagnostic Features.
2. Press and hold the UNLOCK button on either power door lock switch for 4 seconds.
3. All stored DTCs will clear from the BCM.

Verifying Vehicle Repair


Confident verification of a DTC repair can only be done by matching the test descriptions of the DTC and ensuring that the DTC RUNS and
PASSES. To know if a test runs and passes use the scan tool and select DTC Status and note the DTC that needs verification. The status of the
diagnostic test can be now observed. For symptom repairs, drive the vehicle and ensure the symptom is gone.

Diagnostic System Check


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 16
Chevrolet Venture V6-3.4L VIN E 1696

Diagnostic Chart

Refer to Engine Controls Schematics. See: Diagrams/Electrical Diagrams

CIRCUIT DESCRIPTION
The Powertrain On Board Diagnostic (OBD) System Check must be the starting point for any driveability complaint diagnosis. Before using this
procedure, you should perform a careful visual/physical inspection of the PCM and engine grounds for being clean and tight. The Powertrain On
Board Diagnostic (OBD) System Check is an organized approach to identifying a problem created by an electronic engine control system
malfunction.

MIL OPERATION
The Malfunction Indicator Lamp (MIL) is located on the instrument panel and is displayed as CHECK ENGINE lamp.

MIL FUNCTION
^ The MIL informs the driver that a malfunction has occurred and the vehicle should be taken in for service as soon as possible
^ The MIL illuminates during a bulb test and a system test
^ A DTC will be stored if a MIL is requested by the diagnostic

MIL ILLUMINATION
^ The MIL will illuminate with ignition switch ON and the engine not running
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 17
Chevrolet Venture V6-3.4L VIN E 1697
^ The MIL will turn OFF when the engine is started
^ The MIL will remain ON if the self-diagnostic system has detected a malfunction
^ The MIL may turn OFF if the malfunction is not present
^ If the MIL is illuminated and then the engine stalls, the MIL will remain illuminated so long as the ignition switch is ON.
^ If the MIL is not illuminated and the engine stalls, the MIL will not illuminate until the ignition switch is cycled OFF, then ON.

POWERTRAIN ON BOARD DIAGNOSTIC (OBD) SYSTEM CHECK


Perform the Powertrain On Board Diagnostic (OBD) System Check, when the following conditions are present:
^ When the MIL does not turn ON when the ignition switch is turned to the RUN position. See above for MIL Operation
^ When the MIL remains ON while the engine is running
^ When the MIL is flashing while the engine is running
^ When a driveability symptom is determined

DIAGNOSTIC AIDS
An intermittent may be caused by a faulty connection, rubbed through wire insulation, or a wire broken inside the insulation. Inspect for faulty
connections or a damaged harness. Inspect the PCM harness and connectors for improper mating, broken locks, improperly formed or damaged
terminals, faulty terminal to wire connection, and damaged harness. Refer to Intermittent Conditions. See: Initial Inspection and Diagnostic
Overview/Diagnostic Strategies/Intermittent Conditions

TEST DESCRIPTION
The numbers below refer to the step numbers on the diagnostic table:
1. The MIL should be ON steady with the key ON/ engine OFF. If not, the No Malfunction Indicator Lamp table should be used to isolate the
malfunction.
2. This test ensures that the PCM is capable of transmitting Class II serial data to the DLC and that the Class II data circuit is not open or
shorted. If a problem is encountered and a malfunctioning scan tool is suspected, try the scan tool on another vehicle to verify operation. If a
DLC problem exists, the DLC Diagnosis table should be used to diagnose the condition.
4. If the engine will not start, the Engine Cranks But Will Not Run table should be used to diagnose the condition. See: Symptom Related
Diagnostic Procedures
5. The scan tool may display DTCs which are diagnosed in Automatic Transaxle Diagnosis. Refer to DTC List for a complete list of DTCs
supported by this vehicle application. See: Diagnostic Trouble Code Descriptions

If multiple DTCs are stored, diagnose each DTC according the following priority:
^ PCM Error DTCs
^ System Voltage DTCs
^ Component Level DTCs (switches, sensor range/performance, sensor high voltage, sensor low voltage, ODMs, etc.)
^ System level DTCs (Fuel trim, Misfire, EGR flow, TWC System, Idle Control System, HO2S Response or HO2S Transition Time Ratio)
^ System Reference DTCs
6. A scan tool parameter which is not within the typical range may help to isolate the area which is causing the problem.
Strategy Based Diagnostics
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 18
Chevrolet Venture V6-3.4L VIN E 1698

Strategy Based Diagnosis

The goal of Strategy Based Diagnostics is to provide guidance when you create a plan of action for each specific diagnostic situation. Following a
similar plan for each diagnostic situation, you will achieve maximum efliciency when you diagnose and repair vehicles. Although each of the
Strategy Based Diagnostics boxes is numbered, you are not required to complete every box in order to successfully diagnose a customer concern.
The first step of your diagnostic process should always be, Verify the Customer Concern (box 1). The final step of your diagnostic process should
be, Repair and Verify the Fix (box 7). Refer to the chart for the correct strategy based diagnostics.

(1) Verify the Customer Concern: The first part of this step is to obtain as much information as possible from the customer such as: Are there
aftermarket accessories on the vehicle? When does the condition occur? Where does the condition occur? How long and how often does the
condition occur? In order to verify the concern the technician should know the normal operation of the system and refer to the owner or service
manual for any information needed.

(2) Preliminary Checks: Conduct a thorough visual inspection. Review the service history. Detect unusual sounds or odors. Gather diagnostic
trouble code information in order to achieve an effective repair.

(3) Perform Diagnostic System Checks: One or more DTCs may not support a system. System checks verify the proper operation of the system.
This will lead the technician in an organized approach to diagnostics.

(4) Check Bulletins and Other Service Information: Such as videos, newsletters, and the Pulsat programs.

(5.1) Stored DTCs: Follow the designated DTC table exactly in order to make an effective repair.

(5.2) Symptom No DTC: Select the symptom from the symptom tables. Follow the diagnostic steps or suggestions in order to complete the repair,
or refer to the applicable component system check.

(5.3) No Diagnostics: Analyze the concern. Develop a plan for the diagnostics. Schematics will help you to see system power, ground, input and
output circuits. You can also identify splices and other areas where multiple circuits are tied together. Look at component locations to see if
components, connectors or harnesses may be exposed to extreme temperature, moisture, road salt or other corrosives (battery acid, oil or other
fluids). Utilize the wiring diagrams, system description and operation, and system circuit description.

(5.4) Intermittents: An intermittent condition is one that does not occur continuously and will occur when certain conditions are met. Generally,
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 19
Chevrolet Venture V6-3.4L VIN E 1699
intermittents are caused by: Faulty electrical connections and wiring, malfunctioning components, electromagnetic radio frequency interference,
and aftermarket equipment.. Combine the technician knowledge with efficient use of the available service information. Evaluate the symptoms and
conditions described by the customer. Use a check sheet or other method in order to identify the component. Follow the suggestions for intermittent
diagnosis. The Tech 1, Tech 2 scan tools, and the J39200 (Fluke 87) have data capturing capabilities that can assist in detection of intermittents.

(5.5) Vehicle Operates as Designed: This condition exists when the vehicle is found to operate normally. The condition described by the customer
may be normal. Verify against another like vehicle that is operating normally under the same conditions described by the customer. Explain your
findings and the operation of that system to the customer.

(6) Re-examine the Concern: If a technician cannot successfully find or isolate the concern, a reevaluation is necessary. Re-verify the concern.
The concern could be an intermittent or normal.

(7) Repair and Verify Fix: After isolating the cause, make the repairs and validate for proper operation. Verify that the symptom has been
corrected which may involve road testing the vehicle.

Visual and Physical Underhood Inspection


One of the most important inspections is a visual/physical underhood inspection. This can often fix a problem. These quick tests take only a few
minutes, can save valuable time, and help you correct the problem. For further information, refer to Visual/Physical Check in Symptoms. See:
Initial Inspection and Diagnostic Overview

All Powertrain diagnosis should begin with a thorough visual inspection. Visual inspection can often lead to repair of a simple problem without use
of the tables.
- Inspect all vacuum hoses for being pinched, cut, disconnected or misrouted. The EVAP Purge Solenoid vacuum hoses can easily be installed
incorrectly. Be sure to inspect hoses that are difficult to see such as beneath the upper intake, generator, etc.
- Inspect for proper ground connections, ground eyelets connected to ground points, star washers installed, if applicable.
- Inspect the battery positive junction block for loose retainer nuts.
- Inspect other wiring in the engine compartment for good connections, burned or chaffed spots, pinched wires or harness contact with sharp
edges or hot exhaust manifolds.
- Inspect for blown or missing fuses and for relays missing or installed in the wrong locations.

Refer to Power and Grounding Components in Diagrams. See: Diagrams/Electrical Diagrams

Visual/Physical Check
NOTE: Use the connector test adapter kit J 35616-A for any test that requires probing the following items:

- The PCM harness connectors


- The electrical center fuse/relay cavities
- The component terminals
- The component harness connector

Using this kit will prevent damage caused by the improper probing of connector terminals.

Several of the symptom procedures call for a careful visual/physical inspection. This can lead to correcting a problem without further inspections
and can save valuable time. This inspection should include the following areas:
- Inspect the PCM grounds for being clean, tight, and in their proper location. Refer to The PCM grounds, refer to Power Distribution
Schematics, and Ground Distribution Schematics in Diagrams.
- Inspect vacuum hoses for splits, kinks, and proper connections, as shown on Vehicle Emission Control Information label. Inspect thoroughly
for any type of leak or restriction. Refer to Emission Hose Routing Diagram. See: Emission Control Systems
- Inspect the air intake ducts for being collapsed, damaged areas, looseness, improper installation, or leaking especially between the MAF
sensor and the throttle body.
- Inspect for air leaks at throttle body mounting area, Mass Air Flow (MAF) sensor and intake manifold sealing surfaces.
- Inspect the wiring harness for poor connections, pinches, cuts or other damage.
- Inspect for loose, damaged or missing sensors/components.

Use the following tables when diagnosing a symptom complaint:


- Hard Start See: Symptom Related Diagnostic Procedures/Hard Start
- Surges/Chuggles See: Symptom Related Diagnostic Procedures/Surges/Chuggles
- Lack of Power, Sluggishness, or Sponginess See: Symptom Related Diagnostic Procedures/Lack of Power, Sluggishness, or Sponginess
- Detonation/Spark Knock See: Symptom Related Diagnostic Procedures/Detonation, Spark Knock
- Hesitation, Sag, Stumble See: Symptom Related Diagnostic Procedures/Hesitation, Sag or Stumble
- Cuts Out, Misses See: Symptom Related Diagnostic Procedures/Cuts Out, Misses
- Poor Fuel Economy See: Symptom Related Diagnostic Procedures/Poor Fuel Economy
- Poor Fuel Fill Quality See: Symptom Related Diagnostic Procedures/Poor Fuel Fill Quality
- Rough, Unstable, or Incorrect Idle and Stalling See: Symptom Related Diagnostic Procedures/Rough, Unstable, or Incorrect Idle and Stalling
- Dieseling, Run-On See: Symptom Related Diagnostic Procedures/Dieseling, Run-On
- Backfire See: Symptom Related Diagnostic Procedures/Backfire
- Restricted Exhaust System Check See: Component Tests and General Diagnostics/Restricted Exhaust System Check
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 20
Chevrolet Venture V6-3.4L VIN E 1700

Diagnostic Trouble Code (DTC) List/Type

C1214 - C1298
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 21
Chevrolet Venture V6-3.4L VIN E 1701

P0117 - P1115

Diagnostic Trouble Code (DTC) List

Diagnostic Trouble Code (DTC) List/Type


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 22
Chevrolet Venture V6-3.4L VIN E 1702

Diagnostic Trouble Code (DTC) List/Type

Diagnostic Trouble Code (DTC) List/Type


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 23
Chevrolet Venture V6-3.4L VIN E 1703

P0101 - P0300
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 24
Chevrolet Venture V6-3.4L VIN E 1704

P0325 - P0719
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 25
Chevrolet Venture V6-3.4L VIN E 1705

P0724 - P1546
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 26
Chevrolet Venture V6-3.4L VIN E 1706

P1554 - U1305

Transmission Controls
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 27
Chevrolet Venture V6-3.4L VIN E 1707

Engine Controls
This information refers to domestic and export calibration packages. Use the DTCs that only apply to your specific RPO (Regular Production
Option). Each DTC is directly related to a diagnostic test. The DTC sets based upon the DTC's individual running and setting criteria.

The following are the types of DTCs and their code characteristics:

TYPE A
- Emissions related
- Requests illumination of the MIL on the first trip with a fail
- Stores a History DTC on the first trip with a fail
- Stores a Freeze Frame on the first trip with a fail
- Stores a Failure Record
- Updates the Failure Record the first time the test fails each ignition cycle

TYPE B
- Emissions related
- The code is enabled after the first trip with a fail
- The code is disabled if the second consecutive trip passes
- Requests illumination of the MIL on the second consecutive trip with a fail
- Stores a History DTC on the second consecutive trip with a fail
- Stores a Freeze Frame on the second consecutive trip with a fail
- Stores a Failure Record when the first test fails
- Updates the Failure Record the first time the test fails each ignition cycle

TYPE C1
- Non-emissions related
- Requests illumination of the service lamp (not the MIL), or the service message on the first trip with a fail
- Stores a History DTC on the first trip with a fail
- Does not store a Freeze Frame
- Stores a Failure Record when the test fails
- Updates the Failure Record the first time the test fails each ignition cycle

TYPE C0
- Non-missions related
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 28
Chevrolet Venture V6-3.4L VIN E 1708
- Does not request illumination of any lamps
- Stores a History DTC on the first trip with a fail
- Does not store a Freeze Frame
- Stores a Failure Record when the test fails
- Updates the Failure Record the first time the test fails each ignition cycle

TYPE X
- Diagnostics that are coded in the software, but will not run for non-OBD II export vehicles
- Some domestic vehicles use DTCs
- Even though codes are not stored, the DTC Type Table can still be used as a resource when diagnosing problems with systems that are
associated with the type X DTCs

If a system is malfunctioning and the associated DTC has been disabled (Type X), it may be beneficial to use the diagnostic table as a guide to
aid in diagnosis. Many of the DTC tables include a functional check of the system that may pinpoint a problem. However, it is important to
remember that the DTC tables are specifically designed for use only when a DTC is set. Therefore, a thorough understanding of the normal
operation of the system being diagnosed is necessary and use of the tables for this purpose is at the discretion of the technician.
Transmission Controls
DIAGNOSTIC TROUBLE CODE (DTC) TYPE DEFINITIONS
The DTC Type Definitions contain the characteristics for all types of DTCs. Each DTC type may or may not be found. The DTC type is based on
the action that the PCM takes when storing DTC information, and whether or not the PCM illuminates a service lamp or displays a message on a
driver information center (DIC). The DTC descriptions in the Diagnostic Trouble Code List/Type are listed in numeric order and indicate the
DTC types for domestic and export vehicle applications. Each DTC is categorized into one of the following types:

Type A
This DTC is emissions related. The PCM stores the DTC in History, Freeze Frame and Failure Records during the first trip in which the
conditions for setting the DTC are met. The PCM also illuminates the malfunction indicator lamp (MIL) during the first trip in which the
conditions for setting the DTC are met.

Type B
This DTC is emissions related. The PCM stores the DTC in Failure Records during the first trip in which the conditions for setting the DTC are
met. The PCM stores the DTC in History and Freeze Frame during the second consecutive trip in which the conditions for setting the DTC are
met. The PCM also illuminates the MIL during the second consecutive trip in which the conditions for setting the DTC are met.

Type C
This DTC is non-emissions related. The PCM stores the DTC in History and Failure Records during the first trip in which the conditions for
setting the DTC are met. The PCM does not store the DTC in Freeze Frame and does not illuminate the MIL. For some type C DTCs, a message
may be displayed on a DIC, if equipped. For other type C DTCs, a separate service lamp (other than the MIL) may be illuminated. Type C DTCs
that do not display a message on the DIC or illuminate a separate service lamp were formerly referred to as type D.

Type X
This DTC is available in the PCM software, but has been disabled, or turned off. In this case, the diagnostic does not run, DTCs are not stored,
and the MIL does not illuminate. Type X DTCs are used primarily for export vehicles that do not require MIL illumination or DTC storing.

The service information contained in these procedures refer to the domestic (federal) calibration package. Domestic calibrations apply to vehicles
sold in the United States, Canada and Japan. Export calibrations exist for both leaded and unleaded vehicles. DTC types may change for some
export vehicles, and some DTCs may be turned off for leaded export vehicles. Differences between domestic and export calibrations are not
reflected on DTC support information pages. DTC types for export calibrations are referenced only in the Diagnostic Trouble Code (DTC)
List/Type.

Diagnostic Trouble Code (DTC) List/Type


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 29
Chevrolet Venture V6-3.4L VIN E 1709

Diagnostic Trouble Code (DTC) List/Type

Diagnostic Trouble Code (DTC) List/Type

Diagnostic Trouble Code (DTC) List/Type

Diagnostic Trouble Code (DTC) List/Type

Diagnostic Trouble Code (DTC) List/Type

C1214
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 30
Chevrolet Venture V6-3.4L VIN E 1710

Circuit Description
The electronic brake control relay supplies voltage to the solenoid valves and pump motor when energized. This voltage is referred to as the
system voltage. The electronic brake control relay, located in the EBCM, is activated whenever the ignition switch is in the RUN position and no
faults are present. The electronic brake control relay remains energized until the ignition switch is turned off or when ABS is disabled.

Conditions for Running the DTC


^ The ignition voltage is greater than 10.8 volts.
^ The electronic brake control relay is commanded ON.

Conditions for Setting the DTC


^ The system voltage is less than 8 volts.
^ The above conditions are present for greater than 0.23 seconds.
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 31
Chevrolet Venture V6-3.4L VIN E 1711

Action Taken When the DTC Sets


^ ABS/TCS is disabled.
^ ABS/TCS indicators are turned on.

Conditions for Clearing the DTC


^ Condition for DTC is no longer present and scan tool clear DTC function is used.
^ 100 ignition cycles have passed with no DTCs detected.

C1216
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 32
Chevrolet Venture V6-3.4L VIN E 1712

Circuit Description
The EBCM will monitor the on/off state of each solenoid and will recognize when the ABS is in pressure decrease too long. This fault indicates
that the EBCM was unable to decrease brake pressure enough to a certain wheel to prevent excessive wheel slip. This fault can cause erratic ABS
or no ABS operation.

Conditions for Running the DTC


The vehicle is in an ABS stop.

Conditions for Setting the DTC


Any wheel is releasing for greater than 1.0 second while the wheel speed at the wheel is less than 5.0 k/ph (3.0 mph).

Action Taken When the DTC Sets


^ ABS/TCS is disabled.
^ ABS/TCS Indicators are turned on.

Conditions for Clearing the DTC


^ Condition for DTC is no longer present and scan tool clear DTC function is used.
^ 100 ignition cycles have passed with no DTCs detected.

Diagnostic Aids
^ Possible causes for DTC C1216 to set are:
- A contaminated hydraulic unit.
- An intermittent wheel speed sensor.
- A sticking solenoid.
- Excessive brake drag or high resistance in base brake system.
- Suspension system irregularities.
^ It is very important that a thorough inspection of the brake fluid condition, wiring and connectors be performed. Failure to carefully and fully
inspect brake fluid condition, wiring and connectors may result in misdiagnosis, causing part replacement with reappearance of the
malfunction.
^ If an intermittent malfunction exists refer to Testing for Intermittent and Poor Connections Testing for Intermittents, and Poor Connections.

C1217
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 33
Chevrolet Venture V6-3.4L VIN E 1713
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 34
Chevrolet Venture V6-3.4L VIN E 1714

Circuit Description
The pump motor is an integral part of the Brake Pressure Modulator Valve (BPMV). The electronic brake control relay supplies voltage to the
solenoid valves and pump motor. This voltage is referred to as the system voltage. The electronic brake control relay, located in the EBCM, is
activated whenever the ignition switch is in the RUN position and no faults are present. The electronic brake control relay remains engaged until
the ignition switch is turned off or a failure is detected.

Conditions for Running the DTC


^ The ignition is ON.
^ The pump motor has been commanded OFF for 1 second.
^ The system voltage is greater than 9.36 volts.

Conditions for Setting the DTC


Either of the following conditions are present for greater than 0.20 seconds.
10.
^ 16Thevolts
voltage across the pump motor is greater than
^ 70
2. Thevolts.
pump motor low side voltage is no more than

Action Taken When the DTC Sets


^ ABS/TCS is disabled.
^ ABS/TCS indicators are turned on.

Conditions for Clearing the DTC


^ Condition for DTC is no longer present and scan tool clear DTC function is used.
^ 100 ignition cycles have passed with no DTCs detected.

C1218
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 35
Chevrolet Venture V6-3.4L VIN E 1715
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 36
Chevrolet Venture V6-3.4L VIN E 1716

Circuit Description
The pump motor is an integral part of the Brake Pressure Modulator Valve (BPMV). The electronic brake control relay supplies voltage to the
solenoid valves and pump motor. This voltage is referred to as the system voltage. The electronic brake control relay, located in the EBCM, is
activated whenever the ignition switch is in the RUN position and no faults are present. The electronic brake control relay remains engaged until
the ignition switch is turned off or a failure is detected.

Conditions for Running the DTC


^ The pump motor is commanded ON.
^ The system voltage is greater than 8.0 volts.

Conditions for Setting the DTC


Either of the following conditions are present for greater than 0.16 seconds. The voltage across the pump motor is less than 8.0 volts and the
commanded pump motor voltage is greater than or equal to the system voltage. The voltage across the pump motor is 3.0 volts less than and the
pump motor voltage and the commanded pump voltage is greater than or equal to the system voltage.

Action Taken When the DTC Sets


^ ABS/TCS is disabled.
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 37
Chevrolet Venture V6-3.4L VIN E 1717
^ ABS/TCS indicators are turned on.

Conditions for Clearing the DTC


^ Condition for DTC is no longer present and scan tool clear DTC function is used.
^ 100 ignition cycles have passed with no DTCs detected.

C1221
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 38
Chevrolet Venture V6-3.4L VIN E 1718

Circuit Description
The speed sensor used on this vehicle is a multiple pole magnetic pickup. This sensor produces an AC signal when a toothed ring passes the
wheel speed sensor. The EBCM uses the frequency to calculate the wheel speed.

Conditions for Running the DTC


^ DTCs C1232-C1235 are not set.
^ The brake pedal is not pressed.
^ The vehicle is not in an ABS stop.

Conditions for Setting the DTC


^ The left front wheel speed equal to zero.
^ The other wheel speeds are greater than 8 km/h (5 mph).
^ The difference between the other three wheel speed sensors is less than 11 km/h (6.8 mph)
^ The above conditions are present for 2.5 seconds.

Action Taken When the DTC Sets


^ The ABS/TCS disables.
^ The EBCM turns on the ABS and the TRAC OFF (if equipped) indicator(s).
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 39
Chevrolet Venture V6-3.4L VIN E 1719

Conditions for Clearing the DTC


^ Condition for DTC is no longer present and scan tool clear DTC function is used.
^ 100 ignition cycles have passed with no DTC(s) detected.

Diagnostic Aids
^ It is very important that a thorough inspection of the wiring and connectors be performed. Failure to carefully and fully inspect wiring and
connectors may result in misdiagnosis, causing part replacement with reappearance of the malfunction.
^ An intermittent malfunction can be caused by poor connections, broken insulation, or a wire that is broken inside the insulation.
^ If an intermittent malfunction exists refer to Testing for Intermittent and Poor Connections.

Test Description
The numbers below refer to the step numbers on the diagnostic table.
4. This step tests the wheel speed sensor for the proper resistance value.
5. This step ensures that the wheel speed sensor generates the proper voltage.
7. This step tests whether the wheel speed sensor circuits are shorted together.

C1222
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 40
Chevrolet Venture V6-3.4L VIN E 1720

Circuit Description
The speed sensor used on this vehicle is a multiple pole magnetic pickup. This sensor produces an AC signal when a toothed ring passes the
wheel speed sensor. The EBCM uses the frequency to calculate the wheel speed.

Conditions for Running the DTC


^ DTCs C1232-C1235 are not set.
^ The brake pedal is not pressed.
^ The vehicle is not in an ABS stop.

Conditions for Setting the DTC


^ The right front wheel speed is equal to zero.
^ The other wheel speeds are greater than 8 km/h (5 mph).
^ The difference between the other three wheel speed sensors is less than 11 km/h (6.8 mph)
^ The above conditions are present for 2.5 seconds.

Action Taken When the DTC Sets


^ The ABS/TCS disables.
^ The EBCM turns on the ABS and the TRAC OFF (if equipped) indicator(s).
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 41
Chevrolet Venture V6-3.4L VIN E 1721

Conditions for Clearing the DTC


^ Condition for DTC is no longer present and scan tool clear DTC function is used.
^ 100 ignition cycles have passed with no DTC(s) detected.

Diagnostic Aids
^ It is very important that a thorough inspection of the wiring and connectors be performed. Failure to carefully and fully inspect wiring and
connectors may result in misdiagnosis, causing part replacement with reappearance of the malfunction.
^ An intermittent malfunction can be caused by poor connections, broken insulation, or a wire that is broken inside the insulation.
^ If an intermittent malfunction exists refer to Testing for Intermittent and Poor Connections.

Test Description
The numbers below refer to the step numbers on the diagnostic table.
4. This step tests the wheel speed sensor for the proper resistance value.
5. This step ensures that the wheel speed sensor generates the proper voltage.
7. This step tests whether the wheel speed sensor circuits are shorted together.

C1223
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 42
Chevrolet Venture V6-3.4L VIN E 1722

Circuit Description
The speed sensor used on this vehicle is a multiple pole magnetic pickup. This sensor produces an AC signal when a toothed ring passes the
wheel speed sensor. The EBCM uses the frequency to calculate the wheel speed.

Conditions for Running the DTC


^ DTCs C1232-Cl235 are not set.
^ The brake pedal is not pressed.
^ The vehicle is not in an ABS stop.

Conditions for Setting the DTC


^ The left rear wheel speed is equal to zero.
^ The other wheel speeds are greater than 8 km/h (5 mph).
^ The difference between the other three wheel speed sensors is less than 11 km/h (6.8 mph)
^ The above conditions are present for 2.5 seconds.

Action Taken When the DTC Sets


^ The ABS/TCS disables.
^ The EBCM turns on the ABS and the TRAC OFF (if equipped) indicator(s).
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 43
Chevrolet Venture V6-3.4L VIN E 1723

Conditions for Clearing the DTC


^ Condition for DTC is no longer present and scan tool clear DTC function is used.
^ 100 ignition cycles have passed with no DTC(s) detected.

Diagnostic Aids
^ It is very important that a thorough inspection of the wiring and connectors be performed. Failure to carefully and fully inspect wiring and
connectors may result in misdiagnosis, causing part replacement with reappearance of the malfunction.
^ An intermittent malfunction can be caused by poor connections, broken insulation, or a wire that is broken inside the insulation.
^ If an intermittent malfunction exists refer to Testing for Intermittent and Poor Connections.

Test Description
The numbers below refer to the step numbers on the diagnostic table.
4. This step tests the wheel speed sensor for the proper resistance value.
5. This step ensures that the wheel speed sensor generates the proper voltage.
7. This step tests whether the wheel speed sensor circuits are shorted together.

C1224
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 44
Chevrolet Venture V6-3.4L VIN E 1724

Circuit Description
The speed sensor used on this vehicle is a multiple pole magnetic pickup. This sensor produces an AC signal when a toothed ring passes the
wheel speed sensor. The EBCM uses the frequency to calculate the wheel speed.

Conditions for Running the DTC


^ DTCs C1232-C1235 are not set.
^ The brake pedal is not pressed.
^ The vehicle is not in an ABS stop.

Conditions for Setting the DTC


^ The right rear wheel speed is equal to zero.
^ The other wheel speeds are greater than 8 km/h (5 mph).
^ The difference between the other three wheel speed sensors is less than 11 km/h (6.8 mph)
^ The above conditions are present for 2.5 seconds.

Action Taken When the DTC Sets


^ The ABS/TCS disables.
^ The EBCM turns on the ABS and the TRAC OFF (if equipped) indicator(s).
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 45
Chevrolet Venture V6-3.4L VIN E 1725

Conditions for Clearing the DTC


^ Condition for DTC is no longer present and scan tool clear DTC function is used.
^ 100 ignition cycles have passed with no DTC(s) detected.

Diagnostic Aids
^ It is very important that a thorough inspection of the wiring and connectors be performed. Failure to carefully and fully inspect wiring and
connectors may result in misdiagnosis, causing part replacement with reappearance of the malfunction.
^ An intermittent malfunction can be caused by poor connections, broken insulation, or a wire that is broken inside the insulation.
^ If an intermittent malfunction exists refer to Testing for Intermittent and Poor Connections.

Test Description
The numbers below refer to the step numbers on the diagnostic table.
4. This step tests the wheel speed sensor for the proper resistance value.
5. This step ensures that the wheel speed sensor generates the proper voltage.
7. This step tests whether the wheel speed sensor circuits are shorted together.

C1225
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 46
Chevrolet Venture V6-3.4L VIN E 1726

Circuit Description
The speed sensor used on this vehicle is a multiple pole magnetic pickup. This sensor produces an AC signal when a toothed ring passes the
wheel speed sensor. The EBCM uses the frequency to calculate the wheel speed.

Conditions for Running the DTC


^ DTCs C1232-C1235 are not set.
^ The brake pedal is not pressed.

Conditions for Setting the DTC


^ The change in wheel speed is more than 24 km/h (15 mph) in 0.01 second.
^ The above condition must occur 5 times with less than 1.00 second between each occurrence.

Action Taken When the DTC Sets


^ The ABS/TCS disables.
^ The EBCM turns on the ABS and the TRAC OFF (if equipped) indicator(s).

Conditions for Clearing the DTC


^ Condition for DTC is no longer present and scan tool clear DTC function is used.
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 47
Chevrolet Venture V6-3.4L VIN E 1727
^ 100 ignition cycles have passed with no DTC(s) detected.

Diagnostic Aids
^ It is very important that a thorough inspection of the wiring and connectors be performed. Failure to carefully and fully inspect wiring and
connectors may result in misdiagnosis, causing part replacement with reappearance of the malfunction.
^ An intermittent malfunction can be caused by poor connections, broken insulation, or a wire that is broken inside the insulation.
^ If an intermittent malfunction exists refer to Testing for Intermittent and Poor Connections.

Test Description
The numbers below refer to the step numbers on the diagnostic table.
4. This step tests the wheel speed sensor for the proper resistance value.
5. This step ensures that the wheel speed sensor generates the proper voltage.
7. This step tests whether the wheel speed sensor circuits are shorted together.

C1226
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 48
Chevrolet Venture V6-3.4L VIN E 1728

Circuit Description
The speed sensor used on this vehicle is a multiple pole magnetic pickup. This sensor produces an AC signal when a toothed ring passes the
wheel speed sensor. The EBCM uses the frequency to calculate the wheel speed.

Conditions for Running the DTC


^ DTCs C1232-C1235 are not set.
^ The brake pedal is not pressed. Conditions for Setting the DTC
^ The change in wheel speed is more than 24 km/h (15 mph) in 0.01 second.
^ The above condition must occur 5 times with less than 1.00 second between each occurrence.

Action Taken When the DTC Sets


^ The ABS/TCS disables.
^ The EBCM turns on the ABS and the TRAC OFF (if equipped) indicator(s).

Conditions for Clearing the DTC


^ Condition for DTC is no longer present and scan tool clear DTC function is used.
^ 100 ignition cycles have passed with no DTC(s) detected.
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 49
Chevrolet Venture V6-3.4L VIN E 1729

Diagnostic Aids
^ It is very important that a thorough inspection of the wiring and connectors be performed. Failure to carefully and fully inspect wiring and
connectors may result in misdiagnosis, causing part replacement with reappearance of the malfunction.
^ An intermittent malfunction can be caused by poor connections, broken insulation, or a wire that is broken inside the insulation.
^ If an intermittent malfunction exists refer to Testing for Intermittent and Poor Connections.

Test Description
The numbers below refer to the step numbers on the diagnostic table.
4. This step tests the wheel speed sensor for the proper resistance value.
5. This step ensures that the wheel speed sensor generates the proper voltage.
7. This step tests whether the wheel speed sensor circuits are shorted together.

C1227
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 50
Chevrolet Venture V6-3.4L VIN E 1730

Circuit Description
The speed sensor used on this vehicle is a multiple pole magnetic pickup. This sensor produces an AC signal when a toothed ring passes the
wheel speed sensor. The EBCM uses the frequency to calculate the wheel speed.

Conditions for Running the DTC


^ DTCs C1232-C1235 are not set.
^ The brake pedal is not pressed.

Conditions for Setting the DTC


^ The change in wheel speed is more than 24 km/h (15 mph) in 0.01 second.
^ The above condition must occur 5 times with less than 1.00 second between each occurrence.

Action Taken When the DTC Sets


^ The ABS/TCS disables.
^ The EBCM turns on the ABS and the TRAC OFF (if equipped) indicator(s).
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 51
Chevrolet Venture V6-3.4L VIN E 1731

Conditions for Clearing the DTC


^ Condition for DTC is no longer present and scan tool clear DTC function is used.
^ 100 ignition cycles have passed with no DTC(s) detected.

Diagnostic Aids
^ It is very important that a thorough inspection of the wiring and connectors be performed. Failure to carefully and fully inspect wiring and
connectors may result in misdiagnosis, causing part replacement with reappearance of the malfunction.
^ An intermittent malfunction can be caused by poor connections, broken insulation, or a wire that is broken inside the insulation.
^ If an intermittent malfunction exists refer to Testing for Intermittent and Poor Connections.

Test Description
The numbers below refer to the step numbers on the diagnostic table.
4. This step tests the wheel speed sensor for the proper resistance value.
5. This step ensures that the wheel speed sensor generates the proper voltage.
7. This step tests whether the wheel speed sensor circuits are shorted together.

C1228
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 52
Chevrolet Venture V6-3.4L VIN E 1732

Circuit Description
The speed sensor used on this vehicle is a multiple pole magnetic pickup. This sensor produces an AC signal when a toothed ring passes the
wheel speed sensor. The EBCM uses the frequency to calculate the Wheel speed.

Conditions for Running the DTC


^ DTCs C1232-C1235 are not set.
^ The brake pedal is not pressed.

Conditions for Setting the DTC


^ The change in wheel speed is more than 24 km/h (15 mph) in 0.01 second.
^ The above condition must occur 5 times with less than 1.00 second between each occurrence.

Action Taken When the DTC Sets


^ The ABS/TCS disables.
^ The EBCM turns on the ABS and the TRAC OFF (if equipped) indicator(s).

Conditions for Clearing the DTC


^ Condition for DTC is no longer present and scan tool clear DTC function is used.
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 53
Chevrolet Venture V6-3.4L VIN E 1733
^ 100 ignition cycles have passed with no DTC(s) detected.

Diagnostic Aids
^ It is very important that a thorough inspection of the wiring and connectors be performed. Failure to carefully and fully inspect wiring and
connectors may result in misdiagnosis, causing part replacement with reappearance of the malfunction.
^ An intermittent malfunction can be caused by poor connections, broken insulation, or a wire that is broken inside the insulation.
^ If an intermittent malfunction exists refer to Testing for Intermittent and Poor Connections.

Test Description
The numbers below refer to the step numbers on the diagnostic table.
4. This step tests the wheel speed sensor for the proper resistance value.
5. This step ensures that the wheel speed sensor generates the proper voltage.
7. This step tests whether the wheel speed sensor circuits are shorted together.

C1232
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 54
Chevrolet Venture V6-3.4L VIN E 1734

Circuit Description
The speed sensor used on this vehicle is a multiple pole magnetic pickup. This sensor produces an AC signal that the EBCM uses the frequency
from to calculate the wheel speed.

Conditions for Running the DTC


The ignition is ON.

Conditions for Setting the DTC


Either of the following conditions are present for greater than 0.02 seconds.
^ Either wheel speed sensor circuit is open or shorted.
^ The wheel speed sensor is open.

Action Taken When the DTC Sets


^ The ABS/TCS disables.
^ The ABS/TCS indicator(s) turn on.

Conditions for Clearing the DTC


^ The condition responsible for setting the DTC no longer exists and the scan tool Clear DTCs function is used.
^ 100 ignition cycles pass with no DTC(s) detected.
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 55
Chevrolet Venture V6-3.4L VIN E 1735

Diagnostic Aids
^ It is very important that a thorough inspection of the wiring and connectors be performed. Failure to carefully and fully inspect wiring and
connectors may result in misdiagnosis, causing part replacement with reappearance of the malfunction.
^ Thoroughly inspect any circuitry that may be causing the complaint for the following conditions:
- Backed out terminals
- Improper mating
- Improperly formed or damaged terminals
- Poor terminal-to-the ring connections
- Physical damage to the wiring harness
^ The following conditions may cause an intermittent malfunction:
- A poor connection
- Rubbed-through wire insulation
- A broken wire inside the insulation
^ If the customer's comments reflect that the ABS/TCS indicator is on only during moist environmental conditions (rain, snow, vehicle wash),
inspect all the wheel speed sensor circuitry for signs of water intrusion. If the DTC is not current, clear all DTCs and simulate the effects of
water intrusion by using the following procedure:
1. Spray the suspected area with a five percent saltwater solution. (Add two teaspoons of salt to twelve ounces of water to make a five percent
saltwater solution.)
2. Test drive the vehicle over various road surfaces (bumps, turns, etc.) above 40 km/h (25 mph) for at least 30 seconds.
3. If the DTC returns, replace the suspected WSS or WSS harness.
4. Rinse the area thoroughly when completed.
^ If an intermittent malfunction exists refer to Testing for Intermittent and Poor Connections for further diagnosis.

Front Wheel Speed Sensor Resistance

The following table contains resistance values for the front wheel speed sensors at varying sensor temperatures for use in diagnosis. The values
are approximate and can be used as a guideline for diagnosis.

Test Description
The number below refers to the step number on the diagnostic table.
2. This step tests the wheel speed sensor and the wheel speed sensor signal circuits for an open.
3. This step tests the wheel speed sensor and the wheel speed sensor signal circuits for a short to ground.
4. This step tests the wheel speed sensor and the wheel speed sensor signal circuits for a short to voltage.
5. This step tests the wheel speed sensor for the proper resistance value.

C1233
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 56
Chevrolet Venture V6-3.4L VIN E 1736
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 57
Chevrolet Venture V6-3.4L VIN E 1737

Circuit Description
The speed sensor used on this vehicle is a multiple pole magnetic pickup. This sensor produces an AC signal that the EBCM uses the frequency
from to calculate the wheel speed.

Conditions for Running the DTC


The ignition is ON.

Conditions for Setting the DTC


Either of the following conditions are present for greater than 0.02 seconds.
^ Either wheel speed sensor circuit is open or shorted.
^ The wheel speed sensor is open.

Action Taken When the DTC Sets


^ The ABS/TCS disables.
^ The ABS/TCS indicator(s) turn on.

Conditions for Clearing the DTC


^ The condition responsible for setting the DTC no longer exists and the scan tool Clear DTCs function is used.
^ 100 ignition cycles pass with no DTC(s) detected.

Diagnostic Aids
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 58
Chevrolet Venture V6-3.4L VIN E 1738
It is very important that a thorough inspection of the wiring and connectors be performed. Failure to carefully and fully inspect wiring and
connectors may result in misdiagnosis, causing part replacement with reappearance of the malfunction.
^ Thoroughly inspect any circuitry that may be causing the complaint for the following conditions:
- Backed out terminals
- Improper mating
- Improperly formed or damaged terminals
- Poor terminal-to-wiring connections
- Physical damage to the wiring harness
The following conditions may cause an intermittent malfunction:
- A poor connection
- Rubbed-through wire insulation
- A broken wire inside the insulation
^ If the customer's comments reflect that the ABS/TCS indicator is on only during moist environmental conditions (rain, snow, vehicle wash),
inspect all the wheel speed sensor circuitry for signs of water intrusion. If the DTC is not current, clear all DTCs and simulate the effects of
water intrusion by using the following procedure:
1. Spray the suspected area with a five percent saltwater solution. (Add two teaspoons of salt to twelve ounces of water to make a five percent
saltwater solution.)
2. Test drive the vehicle over various road surfaces (bumps, turns, etc.) above 40 km/h (25 mph) for at least 30 seconds.
3. If the DTC returns, replace the suspected WSS or WSS harness.
4. Rinse the area thoroughly when completed.
^ If an intermittent malfunction exists refer to Testing for Intermittent and Poor Connections for further diagnosis.

Front Wheel Speed Sensor Resistance

The following table contains resistance values for the front wheel speed sensors at varying sensor temperatures for use in diagnosis. The values
are approximate and can be used as a guideline for diagnosis.

Test Description
The number below refers to the step number on the diagnostic table.
2. This step tests the wheel speed sensor and the wheel speed sensor signal circuits for an open.
3. This step tests the wheel speed sensor and the wheel speed sensor signal circuits for a short to ground.
4. This step tests the wheel speed sensor and the wheel speed sensor signal circuits for a short to voltage.
5. This step tests the wheel speed sensor for the proper resistance value.

C1234
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 59
Chevrolet Venture V6-3.4L VIN E 1739
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 60
Chevrolet Venture V6-3.4L VIN E 1740

Circuit Description
The speed sensor used on this vehicle is a multiple pole magnetic pickup. This sensor produces an AC signal that the EBCM uses the frequency
from to calculate the wheel speed.

Conditions for Running the DTC


The ignition is ON.

Conditions for Setting the DTC


Either of the following conditions are present for greater than 0.02 seconds.
^ Either wheel speed sensor circuit is open or shorted.
^ The wheel speed sensor is open.

Action Taken When the DTC Sets


^ The ABS/TCS disables.
^ The ABS/TCS indicator(s) turn on.

Conditions for Clearing the DTC


^ The condition responsible for setting the DTC no longer exists and the scan tool Clear DTCs function is used.
^ 100 ignition cycles pass with no DTC(s) detected.

Diagnostic Aids
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 61
Chevrolet Venture V6-3.4L VIN E 1741
^ It is very important that a thorough inspection of the wiring and connectors be performed. Failure to carefully and fully inspect wiring and
connectors may result in misdiagnosis, causing part replacement with reappearance of the malfunction.
^ Thoroughly inspect any circuitry that may be causing the complaint for the following conditions:
- Backed out terminals
- Improper mating
- Improperly formed or damaged terminals
- Poor terminal-to-wiring connections
- Physical damage to the wiring harness
^ The following conditions may cause an intermittent malfunction:
- A poor connection
- Rubbed-through wire insulation
- A broken wire inside the insulation
^ If the customer's comments reflect that the ABS/TCS indicator is on only during moist environmental conditions (rain, snow, vehicle wash),
inspect all the wheel speed sensor circuitry for signs of water intrusion. If the DTC is not current, clear all DTCs and simulate the effects of
water intrusion by using the following procedure:
1. Spray the suspected area with a five percent saltwater solution. (Add two teaspoons of salt to twelve ounces of water to make a five percent
saltwater solution.)
2. Test drive the vehicle over various road surfaces (bumps, turns, etc.) above 40 km/h (25 mph) for at least 30 seconds.
3. If the DTC returns, replace the suspected WSS or WSS harness.
4. Rinse the area thoroughly when completed.
^ If an intermittent malfunction exists refer to Testing for Intermittent and Poor Connections for further diagnosis.

Rear Wheel Speed Sensor Resistance

The following table contains resistance values for the front wheel speed sensors at varying sensor temperatures for use in diagnosis. The values
are approximate and can be used as a guideline for diagnosis.

Test Description
The number below refers to the step number on the diagnostic table.
2. This step tests the wheel speed sensor and the wheel speed sensor signal circuits for an open.
3. This step tests the wheel speed sensor and the wheel speed sensor signal circuits for a short to ground.
4. This step tests the wheel speed sensor and the wheel speed sensor signal circuits for a short to voltage.
5. This step tests the wheel speed sensor for the proper resistance value.

C1235
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 62
Chevrolet Venture V6-3.4L VIN E 1742
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 63
Chevrolet Venture V6-3.4L VIN E 1743

Circuit Description
The speed sensor used on this vehicle is a multiple pole magnetic pickup. This sensor produces an AC signal that the EBCM uses the frequency
from to calculate the wheel speed.

Conditions for Running the DTC


The ignition is ON.
Conditions for Setting the DTC
Either of the following conditions are present for greater than 0.02 seconds.
^ Either wheel speed sensor circuit is open or shorted.
^ The wheel speed sensor is open.

Action Taken When the DTC Sets


^ The ABS/TCS disables.
^ The ABS/TCS indicator(s) turn on.

Conditions for Clearing the DTC


^ The condition responsible for setting the DTC no longer exists and the scan tool Clear DTCs function is used.
^ 100 ignition cycles pass with no DTC(s) detected.

Diagnostic Aids
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 64
Chevrolet Venture V6-3.4L VIN E 1744
^ It is very important that a thorough inspection of the wiring and connectors be performed. Failure to carefully and fully inspect wiring and
connectors may result in misdiagnosis, causing part replacement with reappearance of the malfunction.
^ Thoroughly inspect any circuitry that may be causing the complaint for the following conditions:
- Backed out terminals
- Improper mating
- Improperly formed or damaged terminals
- Poor terminal-to-wiring connections
- Physical damage to the wiring harness
^ The following conditions may cause an intermittent malfunction:
- A poor connection
- Rubbed-through wire insulation
- A broken wire inside the insulation
^ If the customer's comments reflect that the ABS/TCS indicator is on only during moist environmental conditions (rain, snow, vehicle wash),
inspect all the wheel speed sensor circuitry for signs of water intrusion. If the DTC is not current, clear all DTCs and simulate the effects of
water intrusion by using the following procedure:
1. Spray the suspected area with a five percent saltwater solution. (Add two teaspoons of salt to twelve ounces of water to make a five percent
saltwater solution.)
2. Test drive the vehicle over various road surfaces (bumps, turns, etc.) above 40 km/h (25 mph) for at least 30 seconds.
3. If the DTC returns, replace the suspected WSS or WSS harness.
4. Rinse the area thoroughly when completed.
^ If an intermittent malfunction exists refer to Testing for Intermittent and Poor Connections for further diagnosis.

Rear Wheel Speed Sensor Resistance

The following table contains resistance values for the front wheel speed sensors at varying sensor temperatures for use in diagnosis. The values
are approximate and can be used as a guideline for diagnosis.

Test Description
The number below refers to the step number on the diagnostic table.
2. This step tests the wheel speed sensor and the wheel speed sensor signal circuits for an open.
3. This step tests the wheel speed sensor and the wheel speed sensor signal circuits for a short to ground.
4. This step tests the wheel speed sensor and the wheel speed sensor signal circuits for a short to voltage.
5. This step tests the wheel speed sensor for the proper resistance value.

C1236
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 65
Chevrolet Venture V6-3.4L VIN E 1745

Circuit Description
The EBCM monitors the voltage at the Ignition Positive Voltage input and the Battery Positive Voltage circuit at the switch side of the Electronic
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 66
Chevrolet Venture V6-3.4L VIN E 1746
Brake Control Relay. The voltage at the switch side of the Electronic Brake Control Relay is referred to as the system voltage. The EBCM uses
both of the voltages in order to determine if a low voltage condition exists. A low voltage condition prevents the ABS/TCS system from
operating properly.

Conditions for Running the DTC


^ The vehicle speed is greater than 8 km/h (5 mph).
^ The ignition voltage is no more than 10.8 volts.
^ The electronic brake control relay is commanded ON.
AND
Criteria 1
The ABS pump motor is OFF.
OR
Criteria 2
ABS is in initialization.
OR
Criteria 3
ABS or TCS is active.

Conditions for Setting the DTC


Either of the following criteria is present for greater than 0.72 seconds.

Criteria 1 and Criteria 2


The system voltage is no more than 10.8 volts.
OR
Criteria 3
The system voltage is no more than 9.36 volts.

Action Taken When the DTC Sets


^ ABS/TCS is disabled.
^ ABS/TCS Indicators are turned on.

Conditions for Clearing the DTC


^ Condition for DTC is no longer present.
^ The Scan Tool clear DTC function is used.
^ 100 Ignition cycles have passed with no DTCs detected.

C1237
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 67
Chevrolet Venture V6-3.4L VIN E 1747

Circuit Description
The EBCM is required to operate within a specified range of voltage to function properly. The EBCM monitors for high voltage conditions
which could damage the EBCM. The EBCM is designed to detect high vehicle voltage levels to the solenoid relay. High voltage may cause
damage to the system.

Conditions for Running the DTC


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 68
Chevrolet Venture V6-3.4L VIN E 1748
The vehicle speed is greater than 8 km/h (5 mph).

Conditions for Setting the DTC


The battery voltage is greater than 17 volts for 0.72 seconds.

Action Taken When the DTC Sets


^ ABS/TCS is disabled.
^ ABS/TCS Indicators are turned on.

Conditions for Clearing the DTC


^ Condition for DTC is no longer present and scan tool clear DTC function is used.
^ 100 ignition cycles have passed with no DTCs detected.

Diagnostic Aids
^ It is very important that a thorough inspection of the wiring and connectors be performed. Failure to carefully and fully inspect wiring and
connectors may result in misdiagnosis, causing part replacement with reappearance of the malfunction.
^ If an intermittent malfunction exists refer to Testing for Intermittent and Poor Connections.
^ Check for other high voltage conditions.
^ Test the charging system for overcharging conditions. Refer to A Diagnostic System Check - Starting and Charging.

C1238
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 69
Chevrolet Venture V6-3.4L VIN E 1749

Circuit Description
The EBCM monitors vehicle speed deceleration and ABS/TCS activation in order to calculate brake rotor temperatures for the driven wheels.
This sets when the calculated temperature exceeds the a predetermined temperature.

Conditions for Running the DTC


The ABS conditions and the braking conditions are normal.

Conditions for Setting the DTC


DTC C1238 could be set when either driven wheel estimated brake rotor temperature exceeds 375°C (700°F). If either driven wheel estimated
brake rotor temperature has exceeded 375°C (700°F) during ABS or normal braking conditions, the code will not be set until the next TCS
activation occurs. The code will not be set and TCS will not be disabled if both rotor estimated temperatures have cooled below 275°C (530°F)
before the next TCS activation. If either driven wheel brake rotor temperatures has exceeded 375°C (700°F) during TCS then the code will be set
immediately, but TCS will not be disabled until the end of the TCS event.

Action Taken When the DTC Sets


^ The TCS is disabled.
^ The TRAC OFF indicator is turned on.

Conditions for Clearing the DTC


^ The condition for the DTC are no longer present.
^ Cooling of brake rotors.

Diagnostic Aids
^ It should be noted that DTC C1238 may and can set normally during extremely aggressive driving conditions. Always inquire about recent
driving condition or driving habits whenever this code is set.
^ The following conditions are other possible causes of this malfunction:
- Excessive brake usage.
- Excessive TCS usage.
^ When DTC C1238 is set, the following components should be checked for any signs of excessive wear:
- Brake pads.
- Brake rotors.
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 70
Chevrolet Venture V6-3.4L VIN E 1750

C1242
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 71
Chevrolet Venture V6-3.4L VIN E 1751

Circuit Description
The pump motor is an integral part of the Brake Pressure Modulator Valve (BPMV). The electronic brake control relay supplies power to the
solenoid valves and pump motor. This voltage is referred to as the system voltage. The electronic brake control relay, located in the EBCM, is
activated whenever the ignition switch is in the ON position and no faults are present. The electronic brake control relay remains engaged until
the ignition switch is turned off or a failure is detected.

Conditions for Running the DTC


^ The system voltage is greater than 8.0 volts.
^ The system relay is ON.
^ The pump motor is commanded OFF.

Conditions for Setting the DTC


The voltage across the pump motor is between 1.67 and 10.16 volts for 2.0 seconds.

Action Taken When the DTC Sets


^ ABS/TCS is disabled.
^ ABS/TCS indicators are turned on.

Conditions for Clearing the DTC


^ Condition for DTC is no longer present and scan tool clear DTC function is used.
^ 100 ignition cycles have passed with no DTCs detected.

Diagnostic Aids
^ Possible causes for DTC C1242 to set are:
- The pump motor internals has a open.
- The pump motor circuit is open.
^ The pump motor is part of Brake Pressure Modulator Valve (BPMV) and is not serviceable separately.
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 72
Chevrolet Venture V6-3.4L VIN E 1752
^ The solenoid valve control relay is integral to the EBCM and is not serviceable separately.
^ It is very important that a thorough inspection of the wiring and connectors be performed. Failure to carefully and fully inspect wiring and
connectors may result in misdiagnosis, causing part replacement with reappearance of the malfunction.
^ If an intermittent malfunction exists refer to Testing for Intermittent and Poor Connections.

C1243
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 73
Chevrolet Venture V6-3.4L VIN E 1753

Circuit Description
The pump motor is an integral part of the Brake Pressure Modulator Valve (BPMV). The electronic brake control relay supplies power to the
solenoid valves and pump motor. This voltage is referred to as the system voltage. The electronic brake control relay, located in the EBCM, is
activated whenever the ignition switch is in the RUN position and no faults are present. The electronic brake control relay remains engaged until
the ignition switch is turned off or a failure is detected.

Conditions for Running the DTC


^ The pump motor is ON for at least 0.3 seconds.
^ The electronic brake control relay is ON.

Conditions for Setting the DTC


The EBCM determines that the pump motor is turning slowly or not at all.

Action Taken When the DTC Sets


^ ABS/TCS is disabled.
^ ABS/TCS indicators are turned on.

Conditions for Clearing the DTC


^ Condition for DTC is no longer present and scan tool clear DTC function is used.
^ 100 ignition cycles have passed with no DTCs detected.

Diagnostic Aids
^ Possible causes for DTC C1243 to set are:
- The pump motor has high resistance.
- The pump motor jammed (seized).
- The pump motor turns too slowly (due to corroded pump motor or contaminated pump circuit).
^ The pump motor is part of Brake Pressure Modulator Valve (BPMV) and is not serviceable separately.
^ The solenoid valve control relay is integral to the EBCM and is not serviceable separately.
^ It is very important that a thorough inspection of the wiring and connectors be performed. Failure to carefully and fully inspect wiring and
connectors may result in misdiagnosis, causing part replacement with reappearance of the malfunction.
^ If an intermittent malfunction exists refer to Testing for Intermittent and Poor Connections.

C1247
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 74
Chevrolet Venture V6-3.4L VIN E 1754
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 75
Chevrolet Venture V6-3.4L VIN E 1755

Circuit Description
When the master cylinder is low on brake fluid the brake fluid level indicator switch grounds the circuit and turns on the RED brake indicator in
the instrument cluster, then the instrument cluster sends a class 2 message to the EBCM. If the low brake fluid message is sent from the IPC to
the EBCM, TCS will be disabled and a Diagnostic Trouble Code (DTC) sets.

Conditions for Running the DTC


The ignition is ON.

Conditions for Setting the DTC


The EBCM receives a class 2 message from the instrument cluster.

Action Taken When the DTC Sets


^ TCS is disabled.
^ TCS Indicator (TRAC OFF) is turned on.
^ RED Brake indicator is turned on.
^ Service Vehicle Soon indicator is turned on.

Conditions for Clearing the DTC


Condition for DTC is no longer present or scan tool clear DTC function is used.

Diagnostic Aids
^ Possible causes for DTC C1247 to set are:
- Any leaks in hydraulic brake system (such as brake pipes, wheel cylinders, calipers, or master cylinder).
- Brake fluid level indicator switch malfunction.
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 76
Chevrolet Venture V6-3.4L VIN E 1756
- Brake fluid level indicator input circuit is short to ground.
^ It is very important that a thorough inspection of the wiring, connectors, and the hydraulic brake system components be performed. Failure to
carefully and fully inspect wiring, connectors, and hydraulic brake system components may result in misdiagnosis, causing part replacement
with reappearance of the malfunction.
^ If an intermittent malfunction exists refer to Testing for Intermittent and Poor Connections.

C1254
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 77
Chevrolet Venture V6-3.4L VIN E 1757

Circuit Description
When EBCM relay is activated (turned on) voltage is supply to valve solenoids and pump motor. This DTC identifies a malfunction with the
EBCM loosing ground or battery, or when battery is disconnected while running.

Conditions for Running the DTC


The ABS/TCS conditions are normal.

Conditions for Setting the DTC


DTC C1254 is set when an running reset occurs. A running reset is when the vehicle is running and functions are normal then suddenly a loss of
power or ground connection occurs to the EBCM.

Action Taken When the DTC Sets


^ ABS/TCS is disabled.
^ ABS/TCS Indicators are turned on.

Conditions for Clearing the DTC


^ Condition for DTC is no longer present and scan tool clear DTC function is used.
^ 100 ignition cycles have passed with no DTCs detected.

Diagnostic Aids
^ Possible causes for DTC C1254 to set are:
- Running reset occurred.
- Loss of EBCM ground.
- Sudden drop in voltage.
- Poor or loose grounds connections.
- Poor or loose power connections.
- Internal
Battery disconnected
EBCM malfunction.
due to corrosion or loose battery terminals.
^ It is very important that a thorough inspection of the wiring and connectors be performed. Failure to carefully and fully inspect wiring and
connectors may result in misdiagnosis, causing part replacement with reappearance of the malfunction.
^ If an intermittent malfunction exists refer to Testing for Intermittent and Poor Connections.

C1255
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 78
Chevrolet Venture V6-3.4L VIN E 1758

Circuit Description
This DTC identifies a malfunction within the EBCM.

Conditions for Running the DTC


The ABS/TCS conditions are normal.

Conditions for Setting the DTC


DTC C1255 is set when an internal EBCM malfunction exists.

Action Taken When the DTC Sets


^ ABS/TCS is disabled.
^ ABS/TCS Indicators are turned on.

Conditions for Clearing the DTC


^ Condition for DTC is no longer present and scan tool clear DTC function is used.
^ 100 ignition cycles have passed with no DTCs detected.

Diagnostic Aids
^ When DTC C1255 is displayed on the Scan Tool, it will be followed by two more numbers which should be noted along with any other
DTCs that may be displayed. The additional two numbers displayed with DTC C1255 are for aiding engineering to determine the cause of the
internal malfunction.
^ Make sure the integrity of the connection between the EBCM and the BPMV is clean, secure, tight, and free from corrosion.

C1256
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 79
Chevrolet Venture V6-3.4L VIN E 1759

Circuit Description
This DTC identifies a malfunction within the EBCM. When the EBCM relay is activated (turned on), voltage is supplied to the valve solenoids
and pump motor.

Conditions for Running the DTC


The ABS/TCS conditions are normal.

Conditions for Setting the DTC


DTC C1256 is set when an internal EBCM malfunction exists.
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 80
Chevrolet Venture V6-3.4L VIN E 1760

Action Taken When the DTC Sets


^ ABS/TCS is not disabled.
^ ABS/TCS Indicators are not turned on.

Conditions for Clearing the DTC


^ Condition for DTC is no longer present and scan tool clear DTC function is used.
^ 100 ignition cycles have passed with no DTCs detected.

Diagnostic Aids
Possible cause for DTC C1256 to set is an internal relay problem within the EBCM.

C1261

Circuit Description
The inlet valve solenoid circuits are supplied with battery power when the ignition is in the ON position. The EBCM controls the valve functions
by grounding the circuit when necessary.

Conditions for Running the DTC


Criteria 1
^ The switched system battery voltage is greater than 8.0 volts.
^ The ignition voltage is greater than 9.0 volts.
Criteria 2
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 81
Chevrolet Venture V6-3.4L VIN E 1761
^ The switched system battery voltage is greater than 8.0 volts.
^ The ignition voltage is greater than 9.0 volts.
^ ABS is active.

Conditions for Setting the DTC


Either of the following criteria is present for greater than 0.03 seconds.
Criteria 1
The solenoid valve control circuit is open or shorted to ground.
Criteria 2
The solenoid valve control circuit is shorted to voltage.

Action Taken When the DTC Sets


^ The ABS/TCS disables.
^ The ABS/TCS indicator(s) turn on.

Conditions for Clearing the DTC


^ Condition for DTC is no longer present and scan tool clear DTC function is used.
^ 100 ignition cycles have passed with no DTCs detected.

Diagnostic Aids
The solenoid valve circuit and the solenoid coil are internal to the EBCM. No part of the solenoid circuit is diagnosable external to the EBCM.
The DTC sets when there is a malfunction in the solenoid circuit internal to the EBCM only.

C1262
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 82
Chevrolet Venture V6-3.4L VIN E 1762

Circuit Description
The outlet valve solenoid circuits are supplied with battery power when the ignition is in the ON position. The EBCM controls the valve
functions by grounding the circuit when necessary.

Conditions for Running the DTC


Criteria 1
^ The switched system battery voltage is greater than 8.0 volts.
^ The ignition voltage is greater than 9.0 volts.
Criteria 2
^ The switched system battery voltage is greater than 8.0 volts.
^ The ignition voltage is greater than 9.0 volts.
^ ABS is active.

Conditions for Setting the DTC


Either of the following criteria is present for greater than 0.03 seconds.
Criteria 1
^ The solenoid valve control circuit is open or shorted to ground.
Criteria 2
^ The solenoid valve control circuit is shorted to voltage.

Action Taken When the DTC Sets


^ The ABS/TCS disables.
^ The ABS/TCS indicator(s) turn on.

Conditions for Clearing the DTC


^ Condition for DTC is no longer present and scan tool clear DTC function is used.
^ 100 ignition cycles have passed with no DTCs detected.

Diagnostic Aids
The solenoid valve circuit and the solenoid coil are internal to the EBCM. No part of the solenoid circuit is diagnosable external to the EBCM.
The DTC sets when there is a malfunction in the solenoid circuit internal to the EBCM only.

C1263
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 83
Chevrolet Venture V6-3.4L VIN E 1763

Conditions for Running the DTC


^ The switched system battery voltage is greater than 8.0 volts.
^ The ignition voltage is greater than 9.0 volts.

Circuit Description
The inlet valve solenoid circuits are supplied with battery power when the ignition is in the ON position. The EBCM controls the valve functions
by grounding the circuit when necessary.

Conditions for Running the DTC


Criteria 1
^ The switched system battery voltage is greater than 8.0 volts.
^ The ignition voltage is greater than 9.0 volts.
Criteria 2
^ The switched system battery voltage is greater than 8.0 volts.
^ The ignition voltage is greater than 9.0 volts.
^ ABS is active.

Conditions for Setting the DTC


Either of the following criteria is present for greater than 0.03 seconds.
Criteria 1
The solenoid valve control circuit is open or shorted to ground.
Criteria 2
The solenoid valve control circuit is shorted to voltage.
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 84
Chevrolet Venture V6-3.4L VIN E 1764

Action Taken When the DTC Sets


^ The ABS/TCS disables.
^ The ABS/TCS indicator(s) turn on.

Conditions for Clearing the DTC


^ Condition for DTC is no longer present and scan tool clear DTC function is used.
^ 100 ignition cycles have passed with no DTCs detected.

Diagnostic Aids
The solenoid valve circuit and the solenoid coil are internal to the EBCM. No part of the solenoid circuit is diagnosable external to the EBCM.
The DTC sets when there is a malfunction in the solenoid circuit internal to the EBCM only.

C1264

Circuit Description
The outlet valve solenoid circuits are supplied with battery power when the ignition is in the ON position. The EBCM controls the valve
functions by grounding the circuit when necessary.

Conditions for Running the DTC


Criteria 1
^ The switched system battery voltage is greater than 8.0 volts.
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 85
Chevrolet Venture V6-3.4L VIN E 1765
^ The ignition voltage is greater than 9.0 volts.
Criteria 2
^ The switched system battery voltage is greater than 8.0 volts.
^ The ignition voltage is greater than 9.0 volts.
^ ABS is active.

Conditions for Setting the DTC


Either of the following criteria is present for greater than 0.03 seconds.
Criteria 1
The solenoid valve control circuit is open or shorted to ground.
Criteria 2
The solenoid valve control circuit is shorted to voltage.

Action Taken When the DTC Sets


^ The ABS/TCS disables.
^ The ABS/TCS indicator(s) turn on.

Conditions for Clearing the DTC


^ Condition for DTC is no longer present and scan tool clear DTC function is used.
^ 100 ignition cycles have passed with no DTCs detected.

Diagnostic Aids
The solenoid valve circuit and the solenoid coil are internal to the EBCM. No part of the solenoid circuit is diagnosable external to the EBCM.
The DTC sets when there is a malfunction in the solenoid circuit internal to the EBCM only.

C1265
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 86
Chevrolet Venture V6-3.4L VIN E 1766

Circuit Description
The inlet valve solenoid circuits are supplied with battery power when the ignition is in the ON position. The EBCM controls the valve functions
by grounding the circuit when necessary.

Conditions for Running the DTC


Criteria 1
^ The switched system battery voltage is greater than 8.0 volts.
^ The ignition voltage is greater than 9.0 volts.
Criteria 2
^ The switched system battery voltage is greater than 8.0 volts.
^ The ignition voltage is greater than 9.0 volts.
^ ABS is active.

Conditions for Setting the DTC


Either of the following criteria is present for greater than 0.03 seconds.
Criteria 1
The solenoid valve control circuit is open or shorted to ground. Criteria 2
The solenoid valve control circuit is shorted to voltage.

Action Taken When the DTC Sets


^ The ABS/TCS disables.
^ The ABS/TCS indicator(s) turn on. Conditions for Clearing the DTC
^ Condition for DTC is no longer present and scan tool clear DTC function is used.
^ 100 ignition cycles have passed with no DTCs detected.

Diagnostic Aids
The solenoid valve circuit and the solenoid coil are internal to the EBCM. No part of the solenoid circuit is diagnosable external to the EBCM.
The DTC sets when there is a malfunction in the solenoid circuit internal to the EBCM only.

C1266
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 87
Chevrolet Venture V6-3.4L VIN E 1767

Circuit Description
The outlet valve solenoid circuits are supplied with battery power when the ignition is in the ON position. The EBCM controls the valve
functions by grounding the circuit when necessary.

Conditions for Running the DTC


Criteria 1
^ The switched system battery voltage is greater than 8.0 volts.
^ The ignition voltage is greater than 9.0 volts.
Criteria 2
^ The switched system battery voltage is greater than 8.0 volts.
^ The ignition voltage is greater than 9.0 volts.
^ ABS is active.

Conditions for Setting the DTC


Either of the following criteria is present for greater than 0.03 seconds.
Criteria 1
The solenoid valve control circuit is open or shorted to ground.
Criteria 2
The solenoid valve control circuit is shorted to voltage.

Action Taken When the DTC Sets


^ The ABS/TCS disables.
^ The ABS/TCS indicator(s) turn on.
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 88
Chevrolet Venture V6-3.4L VIN E 1768

Conditions for Clearing the DTC


^ Condition for DTC is no longer present and scan tool clear DTC function is used.
^ 100 ignition cycles have passed with no DTCs detected.

Diagnostic Aids
The solenoid valve circuit and the solenoid coil are internal to the EBCM. No part of the solenoid circuit is diagnosable external to the EBCM.
The DTC sets when there is a malfunction in the solenoid circuit internal to the EBCM only.

C1267

Circuit Description
The inlet valve solenoid circuits are supplied with battery power when the ignition is in the ON position. The EBCM controls the valve functions
by grounding the circuit when necessary.

Conditions for Running the DTC


Criteria 1
^ The switched system battery voltage is greater than 8.0 volts.
^ The ignition voltage is greater than 9.0 volts.
Criteria 2
^ The switched system battery voltage is greater than 8.0 volts.
^ The ignition voltage is greater than 9.0 volts.
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 89
Chevrolet Venture V6-3.4L VIN E 1769
^ ABS is active.

Conditions for Setting the DTC


Either of the following criteria is present for greater than 0.03 seconds.
Criteria 1
The solenoid valve control circuit is open or shorted to ground.
Criteria 2
The solenoid valve control circuit is shorted to voltage.

Action Taken When the DTC Sets


^ The ABS/TCS disables.
^ The ABS/TCS indicator(s) turn on.

Conditions for Clearing the DTC


^ Condition for DTC is no longer present and scan tool clear DTC function is used.
^ 100 ignition cycles have passed with no DTCs detected.

Diagnostic Aids
The solenoid valve circuit and the solenoid coil are internal to the EBCM. No part of the solenoid circuit is diagnosable external to the EBCM.
The DTC sets when there is a malfunction in the solenoid circuit internal to the EBCM only.

C1268
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 90
Chevrolet Venture V6-3.4L VIN E 1770

Circuit Description
The outlet valve solenoid circuits are supplied with battery power when the ignition is in the ON position. The EBCM controls the valve
functions by grounding the circuit when necessary.

Conditions for Running the DTC


Criteria 1
^ The switched system battery voltage is greater than 8.0 volts.
^ The ignition voltage is greater than 9.0 volts.
Criteria 2
^ The switched system battery voltage is greater than 8.0 volts.
^ The ignition voltage is greater than 9.0 volts.
^ ABS is active.

Conditions for Setting the DTC


Either of the following criteria is present for greater than 0.03 seconds.
Criteria 1
The solenoid valve control circuit is open or shorted to ground. Criteria 2
The solenoid valve control circuit is shorted to voltage.

Action Taken When the DTC Sets


^ The ABS/TCS disables.
^ The ABS/TCS indicator(s) turn on.

Conditions for Clearing the DTC


^ Condition for DTC is no longer present and scan tool clear DTC function is used.
^ 100 ignition cycles have passed with no DTCs detected.

Diagnostic Aids
The solenoid valve circuit and the solenoid coil are internal to the EBCM. No part of the solenoid circuit is diagnosable external to the EBCM.
The DTC sets when there is a malfunction in the solenoid circuit internal to the EBCM only.

C1272
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 91
Chevrolet Venture V6-3.4L VIN E 1771

Circuit Description
The TCS valve solenoid circuits are supplied with battery power when the ignition is in the ON position. The EBCM controls the valve functions
by grounding the circuit when necessary.

Conditions for Running the DTC


Criteria 1
^ The switched system battery voltage is greater than 8.0 volts.
^ The ignition voltage is greater than 9.0 volts.
Criteria 2
^ The switched system battery voltage is greater than 8.0 volts.
^ The ignition voltage is greater than 9.0 volts.
^ ABS is active.

Conditions for Setting the DTC


Either of the following criteria is present for greater than 0.03 seconds.
Criteria 1
The solenoid valve control circuit is open or shorted to ground.
Criteria 2
The solenoid valve control circuit is shorted to voltage.

Action Taken When the DTC Sets


^ The ABS/TCS disables.
^ The ABS/TCS indicator(s) turn on.
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 92
Chevrolet Venture V6-3.4L VIN E 1772

Conditions for Clearing the DTC


^ Condition for DTC is no longer present and scan tool clear DTC function is used.
^ 100 ignition cycles have passed with no DTCs detected.

Diagnostic Aids
The solenoid valve circuit and the solenoid coil are internal to the EBCM. No part of the solenoid circuit is diagnosable external to the EBCM.
The DTC sets when there is a malfunction in the solenoid circuit internal to the EBCM only.

C1274

Circuit Description
The TCS valve solenoid circuits are supplied with battery power when the ignition is in the ON position. The EBCM controls the valve functions
by grounding the circuit when necessary.

Conditions for Running the DTC


Criteria 1
^ The switched system battery voltage is greater than 8.0 volts.
^ The ignition voltage is greater than 9.0 volts.
Criteria 2
^ The switched system battery voltage is greater than 8.0 volts.
^ The ignition voltage is greater than 9.0 volts.
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 93
Chevrolet Venture V6-3.4L VIN E 1773
^ ABS is active.

Conditions for Setting the DTC


Either of the following criteria is present for greater than 0.03 seconds.
Criteria 1
The solenoid valve control circuit is open or shorted to ground.
Criteria 2
The solenoid valve control circuit is shorted to voltage.

Action Taken When the DTC Sets


^ The ABS/TCS disables.
^ The ABS/TCS indicator(s) turn on.

Conditions for Clearing the DTC


^ Condition for DTC is no longer present and scan tool clear DTC function is used.
^ 100 ignition cycles have passed with no DTCs detected.

Diagnostic Aids
The solenoid valve circuit and the solenoid coil are internal to the EBCM. No part of the solenoid circuit is diagnosable external to the EBCM.
The DTC sets when there is a malfunction in the solenoid circuit internal to the EBCM only.

C1276
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 94
Chevrolet Venture V6-3.4L VIN E 1774

Circuit Description
Traction Control is simultaneously controlled by the EBCM and the Powertrain Control Module (PCM). The PCM sends a DELIVERED
TORQUE message via a Pulse Width Modulated (PWM) signal to the EBCM confirming the delivered torque level for proper Traction Control
system operation. The EBCM supplies the pull up voltage.

Conditions for Running the DTC


The ignition is ON.

Conditions for Setting the DTC


DTC C1276 can be set anytime when ignition voltage is present. A malfunction exists if the PWM signal is out of range or no signal is received
for a period of 7.0 seconds.

Action Taken When the DTC Sets


^ TCS is disabled.
^ Traction Control (TRAC OFF) indicator is turned on.
^ Service Vehicle Soon Indicator is turned on.
^ ABS remains functional.
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 95
Chevrolet Venture V6-3.4L VIN E 1775

Conditions for Clearing the DTC


^ Condition for DTC is no longer present and scan tool clear DTC function is used.
^ 100 ignition cycles have passed with no DTCs detected.

Diagnostic Aids
^ Possible causes for DTC C1276 to set are:
- Delivered Torque line open.
- Delivered Torque line shorted to ground.
- Delivered Torque line shorted to voltage.
- Communication frequency malfunction.
^ It is very important that a thorough inspection of the wiring and connectors be performed. Failure to carefully and fully inspect wiring and
connectors may result in misdiagnosis, causing part replacement with reappearance of the malfunction.
^ If an intermittent malfunction exists refer to Testing for Intermittent and Poor Connections.

C1277
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 96
Chevrolet Venture V6-3.4L VIN E 1776

Circuit Description
Traction Control is simultaneously controlled by the EBCM and the Powertrain Control Module (PCM). The PCM receives a REQUESTED
TORQUE request via a Pulse Width Modulated (PWM) signal from the EBCM requesting the desired torque level for proper Traction Control
system operation. The PCM supplies the pull up voltage.

Conditions for Running the DTC


The ignition is ON.

Conditions for Setting the DTC


DTC C1277 can be set when there is an open or short in the Requested Torque line between the EBCM and PCM or there is a TCS
communication malfunction detected by the PCM and indicated to the EBCM, by broadcasting a Class 2 message.

Action Taken When the DTC Sets


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 97
Chevrolet Venture V6-3.4L VIN E 1777
^ TCS is disabled.
^ Traction Control (TRAC OFF) indicator is turned on.
^ Service Vehicle Soon Indicator is turned on.
^ ABS remains functional.

Conditions for Clearing the DTC


Condition for DTC is no longer present and scan tool is used to clear the history DTC.

Diagnostic Aids
^ Possible causes for DTC C1277 to set are:
- Requested Torque line open.
- Requested Torque line shorted to ground.
- Requested Torque line shorted to voltage.
- Communication frequency malfunction.
- PCM not receiving Class 2 message.
^ It is very important that a thorough inspection of the wiring and connectors be performed. Failure to carefully and fully inspect wiring and
connectors may result in misdiagnosis, causing part replacement with reappearance of the malfunction.
^ If an intermittent malfunction exists refer to Testing for Intermittent and Poor Connections.

C1278

Circuit Description
The PCM monitors various parameters and will not allow traction control operation if any parameter falls below a specified value.

Conditions for Running the DTC


The ignition is ON.

Conditions for Setting the DTC


The PCM detects a malfunction and then causes TCS shut down until the malfunction has been corrected.

Action Taken When the DTC Sets


^ A DTC C1278 is stored (This is a temporary malfunction)
^ The TCS is disabled
^ The TRACTION OFF indicator is turned on
^ ABS remains functional.
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 98
Chevrolet Venture V6-3.4L VIN E 1778

Conditions for Clearing the DTC


^ The condition for the DTC is no longer present and the scan tool clear DTC function is used
^ 100 ignition cycles have passed with no DTCs detected

Diagnostic Aids
This code is for information only. As an aid to the technician, this code indicates that there are no problems in the ABS/TCS system. Any further
references for diagnostic information should be taken from Engine Controls.

C1291
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 99
Chevrolet Venture V6-3.4L VIN E 1779

DTC C1291 Open Brake Lamp Switch Contacts During DecelerationCircuit Description
This DTC is used to detect an open Stoplamp Switch in the non-ABS mode. The EBCM looks for a deceleration rate that would indicate braking
action and verifies this assumption by requiring several repeats of this detection method. In each case, TCS will not be available since no
Stoplamp Switch voltage is seen by the EBCM.

Conditions for Running the DTC


The ABS conditions and the braking conditions are normal.

Conditions for Setting the DTC


DTC C1291 is set after the stoplamp switch remains open for three deceleration cycles. A deceleration cycle includes starting at a speed greater
than 24 km/h (15 mph), then the vehicle must decelerate to 8 km/h (5 mph) for 2 seconds. The vehicle must then reach a speed less than 16 km/h
(10 mph) to complete a deceleration cycle.

Action Taken When the DTC Sets


^ A malfunction DTC is stored.
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 100
Chevrolet Venture V6-3.4L VIN E 1780
^ TCS is disabled.
^ Traction Control indicator is turned on.
^ ABS remains functional.

Conditions for Clearing the DTC


^ Condition for DTC is no longer present and scan tool clear DTC function is used.
^ 100 ignition cycles have passed with no DTCs detected.

Diagnostic Aids
^ Possible causes:
- Stoplamp switch contacts open.
- Stoplamp switch fuse open.
- Stoplamp switch misadjusted.
- Stoplamp switch fuse power feed circuit open.
^ It is very important that a thorough inspection of the wiring and connectors be performed. Failure to carefully and fully inspect wiring and
connectors may result in misdiagnosis, causing part replacement with reappearance of the malfunction.
^ If any Wheel Speed Sensor DTCs are present you must diagnose them first.
^ An intermittent malfunction is most likely caused by a poor connection, rubbed through wire insulation, or a wire that is broken inside the
insulation.

C1293

Circuit Description
This DTC is the second portion of DTC C1291. If DTC C1291 occurred during an ignition cycle, DTC C1293 becomes a current malfunction
during the next ignition cycle, keeping TCS disabled until a brake switch on state is seen. When a change is seen during an ignition cycle in
which DTC C1293 is a current malfunction, DTC C1291 will clear itself at the end of the current ignition cycle, and TCS will enable itself at the
start of the next ignition cycle. DTC C1293 alone indicates DTC C1291 occurred previously, but is intermittent, or has been corrected.

Conditions for Running the DTC


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 101
Chevrolet Venture V6-3.4L VIN E 1781
The ABS conditions and the braking conditions are normal.

Conditions for Setting the DTC


DTC C1293 is set when DTC C1291 was set in the previous or current ignition cycle.

Action Taken When the DTC Sets


^ A malfunction DTC is stored.
^ TCS is disabled.
^ Traction Control indicator is turned on.
^ ABS remains functional.

Conditions for Clearing the DTC


^ Condition for DTC is no longer present and scan tool clear DTC function is used.
^ 100 ignition cycles have passed with no DTCs detected.

Diagnostic Aids
^ Possible causes:
- Stoplamp switch fuse open.
- Stoplamp switch contacts open.
- Stoplamp switch misadjusted.
- Stoplamp switch fuse power feed circuit open.
^ It is very important that a thorough inspection of the wiring and connectors be performed. Failure to carefully and fully inspect wiring and
connectors may result in misdiagnosis, causing part replacement with reappearance of the malfunction.
^ An intermittent malfunction is most likely caused by a poor connection, rubbed through wire insulation, or a wire that is broken inside the
insulation.
^ Also, verify proper stoplamp switch operation using the Data List of the scan tool. As the brake is applied, the data list should display the
stoplamp switch on within 1 inch of travel.

C1294
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 102
Chevrolet Venture V6-3.4L VIN E 1782

Circuit Description
This DTC occurs when internal self-checking safety logic has determined that the Stoplamp Switch is continuously on. This is important because
the TCS can not be activated when the Stoplamp Switch is on.

Conditions for Running the DTC


The vehicle speed is greater than 40 km/h (25 mph).

Conditions for Setting the DTC


DTC C1294 can be set if the vehicle speed reaches at least 40 km/h (25 mph). If the brake lamp switch is always on during two consecutive drive
cycles, a malfunction exists.

Action Taken When the DTC Sets


^ A malfunction DTC is stored.
^ TCS is disabled.
^ Traction Control indicator is turned on.
^ ABS remains functional.

Conditions for Clearing the DTC


^ Condition for DTC is no longer present and scan tool clear DTC function is used.
^ 100 ignition cycles have passed with no DTCs detected.

Diagnostic Aids
^ Possible causes:
- Stoplamp switch circuit shorted to voltage.
- Stoplamp switch misadjusted or shorted.
- Sticking contacts inside stoplamp switch.
- Binding pedal.
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 103
Chevrolet Venture V6-3.4L VIN E 1783
^ It is very important that a thorough inspection of the wiring and connectors be performed. Failure to carefully and fully inspect wiring and
connectors may result in misdiagnosis, causing part replacement with reappearance of the malfunction.

C1295

Circuit Description
The EBCM sources 5 volts on the stoplamp signal circuit. The voltage is supplied a ground path through the stoplamp bulbs. This DTC sets
when the path to ground is open or has high resistance.
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 104
Chevrolet Venture V6-3.4L VIN E 1784

Conditions for Running the DTC


This DTC can set at anytime that the EBCM is powered.

Conditions for Setting the DTC


^ The stoplamp switch signal voltage is between 2.2 volts and 5.0 volts.
^ The above condition is present for greater than 2.0 seconds.

Action Taken When the DTC Sets


^ TCS is disabled
^ Traction Control indicator is turned on
^ ABS remains functional

Conditions for Clearing the DTC


^ Condition for DTC is no longer present and scan tool clear DTC function is used.
^ 100 ignition cycles have passed with no DTCs detected.

Diagnostic Aids
^ Possible causes:
- Stoplamp switch input circuit open.
- All stoplamps open.
- Open stoplamp ground.
-Circuit has a wiring problem, terminal corrosion, or poor connections.
^ It is very important that a thorough inspection of the wiring and connectors be performed. Failure to carefully and fully inspect wiring and
connectors may result in misdiagnosis, causing part replacement with reappearance of the malfunction.
^ If an intermittent malfunction exists refer to Testing for Intermittent and Poor Connections.

Test Description
The number(s) below refer to the step number(s) on the diagnostic table.
3. This DTC detects an open stop lamp signal circuit from the stoplamp side of the IP Accessory Wiring Junction Block to the EBCM.
4. The EBCM sources 5 volts on the stoplamp signal circuit. This small voltage has a ground path through the stoplamp bulbs. This DTC sets if
the path to ground is open.

C1298
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 105
Chevrolet Venture V6-3.4L VIN E 1785

Circuit Description
The Class 2 serial data line allows all the modules on the line to transmit information to each other as needed. Each module is assigned an ID and
all the information sent out on the line is assigned a priority by which it is received. When the ignition switch is turned to the ON position, each
module will begin to send and receive information. Each module on the Class 2 serial data line knows what information it needs to send out and
what information it should be receiving. What the modules do not know is which module is supposed to send them the information. This
information is only learned after the module has received the information it needs along with the ID of the module that sent the information. This
information is then remembered until the ignition switch is turned off.

Conditions for Running the DTC


The ABS conditions and the braking conditions are normal.

Conditions for Setting the DTC


DTC C1298 can be set any time the ignition is on, and the PCM does not receive any communications from the EBCM.

Action Taken When the DTC Sets


^ A DTC C1298 is stored.
^ The TCS is disabled.
^ The TRAC OFF indicator is turned on.
^ The ABS remains functional.

Conditions for Clearing the DTC


^ The condition for the DTC is no longer present and the scan tool clear DTC function is used.
^ 100 ignition cycles have passed with no DTCs detected.

Diagnostic Aids
^ Thoroughly inspect the wiring and the connectors. Failure to carefully and fully inspect the wiring and the connectors can result in
misdiagnosis. Misdiagnosis may cause replacement of parts without repairing the malfunction.
^ An intermittent malfunction is most likely caused by a poor connection, rubbed through wire insulation, or a wire that is broken inside the
insulation.
^ Refer to Testing for Intermittent and Poor Connections for intermittent problems.

Important Information - PIT3154


Subject: All GM Vehicles Using Class 2 Communications Diagnostic Strategy for DTC U1000 or U1255 - PIT3154 - (09/10/2004)

Models: (All GM vehicles using Class 2 communications)

The following diagnosis might be helpful if the vehicle exhibits the symptom described in the PI.

Condition/Concern:
DTC U1000 or U1255 set current or history, with or without other DTCs

Recommendation/Instructions:
DTC U1000 Class 2 Data Link
DTC U1255 Lost Communications

These DTCs set when the control module does not receive a message that it was expecting from another control module, and does not know
which control module did not send that message.

1. If the DTC U1000 or U1255 is set in history with other DTCs set current or history, diagnose the other DTCs first.
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 106
Chevrolet Venture V6-3.4L VIN E 1786

2. If the DTC U1000 or U1255 set current, this usually indicates a module that is currently not communicating or a configuration issue.

For example, if the control module is configured for an option (ie: Onstar, Keyless Entry, Memory Mirrors, etc.) that the vehicle does not
have, it may expect to receive a message regarding this missing feature. This would usually occur due to the control module being recently
replaced and incorrectly setup.

3. When the DTC U1000 or U1255 is current, the module that is not communicating may not even be listed on the Tech 2 on the Diagnostic
Circuit Check/Class 2 Message Monitor list.

4. If the DTC U1000 or U1255 has set in history without other DTCs, replacing the control module setting the DTC is most likely NOT the
solution. The module that has set the code is looking for an input from another module that is not communicating. Since the module did not
receive an input that it is expecting to see, it sets a U1000 or U1255 which indicates there was a loss of communications. Look at the
customer's complaint (ie: intermittent, erratic tachometer operation); this will probably be a better indication of the control module that is the
source of the concern.

Please follow this diagnosis process thoroughly and complete each step. If the condition exhibited is resolved without completing every step, the
remaining steps do not need to be performed. If these steps do not resolve the condition.
Data Link Communications
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 107
Chevrolet Venture V6-3.4L VIN E 1787

Diagnostic Chart (Part 1 of 2)


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 108
Chevrolet Venture V6-3.4L VIN E 1788

Diagnostic Chart (Part 2 of 2)

CIRCUIT DESCRIPTION
Modules connected to the class 2 serial data circuit monitor for serial data communications during normal vehicle operation. Operating
information and commands are exchanged among the modules. When a module receives a message for a critical operating parameter, the module
records the identification number of the module which sent the message for State of Health monitoring. A critical operating parameter is one
which, when not received, requires that the module use a default value for that parameter. When a module does not associate an identification
number with at least one critical parameter within about five seconds of beginning serial data communication, DTC U1000 or U1255 is set.
When more than one critical parameter does not have an identification number associated with it, the DTC will only be reported once.

CONDITIONS FOR RUNNING THE DTC


^ Voltage supplied to the module is in the normal operating voltage range (approximately 9 to 16 volts).
^ Diagnostic trouble codes U1300 and U1301 and U1305 do not have a current status.
^ The vehicle power mode (ignition switch position) requires serial data communication to occur.

CONDITIONS FOR SETTING THE DTC


At least one critical operating parameter has not been associated with an identification number within about five seconds after beginning serial
data communication.

ACTION TAKEN WHEN THE DTC SETS


The module uses a default value for the missing parameter.

CONDITIONS FOR CLEARING THE DTC


^ A current DTC U1000 or U1255 will clear when all critical operating parameters for the module have been associated with an identification
number or at the end of the current ignition cycle.
^ A history DTC U1000 or U1255 will clear upon receipt of a scan tool Clear DTCs command.

DIAGNOSTIC AIDS
When a malfunction (such as an open fuse to a module) occurs while modules are communicating, a Lost Communication DTC is set as a current
DTC. When the modules stop communicating (ignition is turned OFF) the current Lost Communication DTC is cleared but the history DTC
remains. When the modules begin to communicate again, the module with the open fuse will not be learned by the other modules so DTC U1000
or U1255 is set current by the other modules. If the malfunction occurs when the modules are not communicating, only DTC U1000 or U1255 is
set.

TEST DESCRIPTION
The number(s) below refer to the step number(s) on the diagnostic table.
1. A Lost Communication with XXX DTC with a history status may indicate the cause of U1000 or U1255.
2. The module(s) which is not communicating is the likely cause of U1000 or U1255 being set. The following modules communicate on the
class 2 serial data circuit:
^ PCM
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 109
Chevrolet Venture V6-3.4L VIN E 1789
^ EBCM
^ SDM
^ IPC
^ PK3
^ DID
^ Radio
5. The module which was not communicating may have set Lost Communication with XXX DTCs for those modules that it was monitoring.
6. The module which was not communicating may have set Lost Communication with XXX DTCs for those modules that it was monitoring.
7. The module which was not communicating may have set Lost Communication with XXX DTCs for those modules that it was monitoring.
11. The modules which can communicate indicate the module which cannot communicate. You must clear the DTC from these modules to avoid
future misdiagnosis.
13. If all modules are communicating, the module which set U1000 or U1255 may have done so due to some other condition.
14. The module which set U1000 or U1255 is the likely cause of the malfunction.

U1016

Diagnostic Chart
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 110
Chevrolet Venture V6-3.4L VIN E 1790

The Control Module ID Number list provides a method for determining which module is not communicating. A module with an internal class 2
serial data circuit malfunction or which loses power during the current ignition cycle would have a Lost Communication DTC set by other modules.
Use the Control Module ID Number list in order to determine which module is not communicating and the Lost Communications with XXX
diagnostic table in order to diagnose the malfunction.

Diagnostic Chart

Circuit Description
Modules connected to the class 2 serial data circuit monitor for serial data communications during normal vehicle operation. Operating
information and commands are exchanged among the modules. When a module receives a message for a critical operating parameter, the module
records the identification number of the module which sent the message for State of Health monitoring (Node Alive messages). A critical
operating parameter is one which, when not received, requires that the module use a default value for that parameter. Once an identification
number is learned by a module, it will monitor for that module's Node Alive message. Each module on the class 2 serial data circuit which is
powered and performing functions that require detection of a communications malfunction is required to send a Node Alive message every two
seconds. When no message is detected from a learned identification number for five seconds, a DTC U1XXX (where XXX is equal to the three
digit identification number) is set.

Conditions For Running The DTC


^ Voltage supplied to the module is in the normal operating voltage range (approximately 9 - 16 volts).
^ A short to ground or B+ is not present. Diagnostic trouble codes U1300 and U1301 and U1305 are not set.
^ The vehicle power mode (ignition switch position) requires serial data communication to occur.

Conditions For Setting The DTC


A message from a learned identification number has not been detected for the past five seconds.

Conditions For Clearing The DTC


^ A current DTC will clear when a Node Alive message from the failed identification number is detected on the class 2 serial data circuit or at
the end of the current ignition cycle.
^ A history DTC will clear upon receipt of a scan tool Clear DTCs command.

Diagnostic Aids
^ An intermittent open between the inoperative module and the splice pack SP205 or may cause this code to set.
^ A poor connection at the inoperative module or the splice pack SP205 may cause this code to set.
^ An intermittent open in the splice pack SP205 may cause this code to set.
^ An improperly powered module may cause this code to set.

Test Description
The number(s) below refer to the step number(s) on the diagnostic table.
1. A module which loses power during an ignition cycle will cause other module(s) to set Lost Communication DTCs.
2. A module which loses power during an ignition cycle will cause other module(s) to set Lost Communication DTCs.
3. The malfunction is due to an open in the class 2 serial data circuit or an open in the module.
7. The module which was not communicating may have set Lost Communication DTCs for those modules that it was monitoring.
9. The modules which can communicate indicate the module which cannot communicate. You must clear the DTC from these modules to avoid
future misdiagnosis.

U1040
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 111
Chevrolet Venture V6-3.4L VIN E 1791

Diagnostic Chart

The Control Module ID Number list provides a method for determining which module is not communicating. A module with an internal class 2
serial data circuit malfunction or which loses power during the current ignition cycle would have a Lost Communication DTC set by other modules.
Use the Control Module ID Number list in order to determine which module is not communicating and the Lost Communications with XXX
diagnostic table in order to diagnose the malfunction.
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 112
Chevrolet Venture V6-3.4L VIN E 1792

Diagnostic Chart

Circuit Description
Modules connected to the class 2 serial data circuit monitor for serial data communications during normal vehicle operation. Operating
information and commands are exchanged among the modules. When a module receives a message for a critical operating parameter, the module
records the identification number of the module which sent the message for State of Health monitoring (Node Alive messages). A critical
operating parameter is one which, when not received, requires that the module use a default value for that parameter. Once an identification
number is learned by a module, it will monitor for that module's Node Alive message. Each module on the class 2 serial data circuit which is
powered and performing functions that require detection of a communications malfunction is required to send a Node Alive message every two
seconds. When no message is detected from a learned identification number for five seconds, a DTC U1XXX (where XXX is equal to the three
digit identification number) is set.

Conditions For Running The DTC


^ Voltage supplied to the module is in the normal operating voltage range (approximately 9 - 16 volts).
^ A short to ground or B+ is not present. Diagnostic trouble codes U1300 and U1301 and U1305 are not set.
^ The vehicle power mode (ignition switch position) requires serial data communication to occur.

Conditions For Setting The DTC


A message from a learned identification number has not been detected for the past five seconds.

Conditions For Clearing The DTC


^ A current DTC will clear when a Node Alive message from the failed identification number is detected on the class 2 serial data circuit or at
the end of the current ignition cycle.
^ A history DTC will clear upon receipt of a scan tool Clear DTCs command.

Diagnostic Aids
^ An intermittent open between the inoperative module and the splice pack SP205 or may cause this code to set.
^ A poor connection at the inoperative module or the splice pack SP205 may cause this code to set.
^ An intermittent open in the splice pack SP205 may cause this code to set.
^ An improperly powered module may cause this code to set.

Test Description
The number(s) below refer to the step number(s) on the diagnostic table.
1. A module which loses power during an ignition cycle will cause other module(s) to set Lost Communication DTCs.
2. A module which loses power during an ignition cycle will cause other module(s) to set Lost Communication DTCs.
3. The malfunction is due to an open in the class 2 serial data circuit or an open in the module.
7. The module which was not communicating may have set Lost Communication DTCs for those modules that it was monitoring.
9. The modules which can communicate indicate the module which cannot communicate. You must clear the DTC from these modules to avoid
future misdiagnosis.

U1088
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 113
Chevrolet Venture V6-3.4L VIN E 1793

Diagnostic Chart

The Control Module ID Number list provides a method for determining which module is not communicating. A module with an internal class 2
serial data circuit malfunction or which loses power during the current ignition cycle would have a Lost Communication DTC set by other modules.
Use the Control Module ID Number list in order to determine which module is not communicating and the Lost Communications with XXX
diagnostic table in order to diagnose the malfunction.
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 114
Chevrolet Venture V6-3.4L VIN E 1794

Diagnostic Chart

Circuit Description
Modules connected to the class 2 serial data circuit monitor for serial data communications during normal vehicle operation. Operating
information and commands are exchanged among the modules. When a module receives a message for a critical operating parameter, the module
records the identification number of the module which sent the message for State of Health monitoring (Node Alive messages). A critical
operating parameter is one which, when not received, requires that the module use a default value for that parameter. Once an identification
number is learned by a module, it will monitor for that module's Node Alive message. Each module on the class 2 serial data circuit which is
powered and performing functions that require detection of a communications malfunction is required to send a Node Alive message every two
seconds. When no message is detected from a learned identification number for five seconds, a DTC U1XXX (where XXX is equal to the three
digit identification number) is set.

Conditions For Running The DTC


^ Voltage supplied to the module is in the normal operating voltage range (approximately 9 - 16 volts).
^ A short to ground or B+ is not present. Diagnostic trouble codes U1300 and U1301 and U1305 are not set.
^ The vehicle power mode (ignition switch position) requires serial data communication to occur.

Conditions For Setting The DTC


A message from a learned identification number has not been detected for the past five seconds.

Conditions For Clearing The DTC


^ A current DTC will clear when a Node Alive message from the failed identification number is detected on the class 2 serial data circuit or at
the end of the current ignition cycle.
^ A history DTC will clear upon receipt of a scan tool Clear DTCs command.

Diagnostic Aids
^ An intermittent open between the inoperative module and the splice pack SP205 or may cause this code to set.
^ A poor connection at the inoperative module or the splice pack SP205 may cause this code to set.
^ An intermittent open in the splice pack SP205 may cause this code to set.
^ An improperly powered module may cause this code to set.

Test Description
The number(s) below refer to the step number(s) on the diagnostic table.
1. A module which loses power during an ignition cycle will cause other module(s) to set Lost Communication DTCs.
2. A module which loses power during an ignition cycle will cause other module(s) to set Lost Communication DTCs.
3. The malfunction is due to an open in the class 2 serial data circuit or an open in the module.
7. The module which was not communicating may have set Lost Communication DTCs for those modules that it was monitoring.
9. The modules which can communicate indicate the module which cannot communicate. You must clear the DTC from these modules to avoid
future misdiagnosis.

U1096
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 115
Chevrolet Venture V6-3.4L VIN E 1795

Diagnostic Chart

The Control Module ID Number list provides a method for determining which module is not communicating. A module with an internal class 2
serial data circuit malfunction or which loses power during the current ignition cycle would have a Lost Communication DTC set by other modules.
Use the Control Module ID Number list in order to determine which module is not communicating and the Lost Communications with XXX
diagnostic table in order to diagnose the malfunction.
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 116
Chevrolet Venture V6-3.4L VIN E 1796

Diagnostic Chart

Circuit Description
Modules connected to the class 2 serial data circuit monitor for serial data communications during normal vehicle operation. Operating
information and commands are exchanged among the modules. When a module receives a message for a critical operating parameter, the module
records the identification number of the module which sent the message for State of Health monitoring (Node Alive messages). A critical
operating parameter is one which, when not received, requires that the module use a default value for that parameter. Once an identification
number is learned by a module, it will monitor for that module's Node Alive message. Each module on the class 2 serial data circuit which is
powered and performing functions that require detection of a communications malfunction is required to send a Node Alive message every two
seconds. When no message is detected from a learned identification number for five seconds, a DTC U1XXX (where XXX is equal to the three
digit identification number) is set.

Conditions For Running The DTC


^ Voltage supplied to the module is in the normal operating voltage range (approximately 9 - 16 volts).
^ A short to ground or B+ is not present. Diagnostic trouble codes U1300 and U1301 and U1305 are not set.
^ The vehicle power mode (ignition switch position) requires serial data communication to occur.

Conditions For Setting The DTC


A message from a learned identification number has not been detected for the past five seconds.

Conditions For Clearing The DTC


^ A current DTC will clear when a Node Alive message from the failed identification number is detected on the class 2 serial data circuit or at
the end of the current ignition cycle.
^ A history DTC will clear upon receipt of a scan tool Clear DTCs command.

Diagnostic Aids
^ An intermittent open between the inoperative module and the splice pack SP205 or may cause this code to set.
^ A poor connection at the inoperative module or the splice pack SP205 may cause this code to set.
^ An intermittent open in the splice pack SP205 may cause this code to set.
^ An improperly powered module may cause this code to set.

Test Description
The number(s) below refer to the step number(s) on the diagnostic table.
1. A module which loses power during an ignition cycle will cause other module(s) to set Lost Communication DTCs.
2. A module which loses power during an ignition cycle will cause other module(s) to set Lost Communication DTCs.
3. The malfunction is due to an open in the class 2 serial data circuit or an open in the module.
7. The module which was not communicating may have set Lost Communication DTCs for those modules that it was monitoring.
9. The modules which can communicate indicate the module which cannot communicate. You must clear the DTC from these modules to avoid
future misdiagnosis.

U1192
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 117
Chevrolet Venture V6-3.4L VIN E 1797

Diagnostic Chart

The Control Module ID Number list provides a method for determining which module is not communicating. A module with an internal class 2
serial data circuit malfunction or which loses power during the current ignition cycle would have a Lost Communication DTC set by other modules.
Use the Control Module ID Number list in order to determine which module is not communicating and the Lost Communications with XXX
diagnostic table in order to diagnose the malfunction.
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 118
Chevrolet Venture V6-3.4L VIN E 1798

Diagnostic Chart

Circuit Description
Modules connected to the class 2 serial data circuit monitor for serial data communications during normal vehicle operation. Operating
information and commands are exchanged among the modules. When a module receives a message for a critical operating parameter, the module
records the identification number of the module which sent the message for State of Health monitoring (Node Alive messages). A critical
operating parameter is one which, when not received, requires that the module use a default value for that parameter. Once an identification
number is learned by a module, it will monitor for that module's Node Alive message. Each module on the class 2 serial data circuit which is
powered and performing functions that require detection of a communications malfunction is required to send a Node Alive message every two
seconds. When no message is detected from a learned identification number for five seconds, a DTC U1XXX (where XXX is equal to the three
digit identification number) is set.

Conditions For Running The DTC


^ Voltage supplied to the module is in the normal operating voltage range (approximately 9 - 16 volts).
^ A short to ground or B+ is not present. Diagnostic trouble codes U1300 and U1301 and U1305 are not set.
^ The vehicle power mode (ignition switch position) requires serial data communication to occur.

Conditions For Setting The DTC


A message from a learned identification number has not been detected for the past five seconds.

Conditions For Clearing The DTC


^ A current DTC will clear when a Node Alive message from the failed identification number is detected on the class 2 serial data circuit or at
the end of the current ignition cycle.
^ A history DTC will clear upon receipt of a scan tool Clear DTCs command.

Diagnostic Aids
^ An intermittent open between the inoperative module and the splice pack SP205 or may cause this code to set.
^ A poor connection at the inoperative module or the splice pack SP205 may cause this code to set.
^ An intermittent open in the splice pack SP205 may cause this code to set.
^ An improperly powered module may cause this code to set.

Test Description
The number(s) below refer to the step number(s) on the diagnostic table.
1. A module which loses power during an ignition cycle will cause other module(s) to set Lost Communication DTCs.
2. A module which loses power during an ignition cycle will cause other module(s) to set Lost Communication DTCs.
3. The malfunction is due to an open in the class 2 serial data circuit or an open in the module.
7. The module which was not communicating may have set Lost Communication DTCs for those modules that it was monitoring.
9. The modules which can communicate indicate the module which cannot communicate. You must clear the DTC from these modules to avoid
future misdiagnosis.

Important Information
Subject: All GM Vehicles Using Class 2 Communications Diagnostic Strategy for DTC U1000 or U1255 - PIT3154 - (09/10/2004)

Models: (All GM vehicles using Class 2 communications)

The following diagnosis might be helpful if the vehicle exhibits the symptom described in the PI.

Condition/Concern:
DTC U1000 or U1255 set current or history, with or without other DTCs

Recommendation/Instructions:
DTC U1000 Class 2 Data Link
DTC U1255 Lost Communications

These DTCs set when the control module does not receive a message that it was expecting from another control module, and does not know
which control module did not send that message.
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 119
Chevrolet Venture V6-3.4L VIN E 1799

1. If the DTC U1000 or U1255 is set in history with other DTCs set current or history, diagnose the other DTCs first.

2. If the DTC U1000 or U1255 set current, this usually indicates a module that is currently not communicating or a configuration issue.

For example, if the control module is configured for an option (ie: Onstar, Keyless Entry, Memory Mirrors, etc.) that the vehicle does not
have, it may expect to receive a message regarding this missing feature. This would usually occur due to the control module being recently
replaced and incorrectly setup.

3. When the DTC U1000 or U1255 is current, the module that is not communicating may not even be listed on the Tech 2 on the Diagnostic
Circuit Check/Class 2 Message Monitor list.

4. If the DTC U1000 or U1255 has set in history without other DTCs, replacing the control module setting the DTC is most likely NOT the
solution. The module that has set the code is looking for an input from another module that is not communicating. Since the module did not
receive an input that it is expecting to see, it sets a U1000 or U1255 which indicates there was a loss of communications. Look at the
customer's complaint (ie: intermittent, erratic tachometer operation); this will probably be a better indication of the control module that is the
source of the concern.

Please follow this diagnosis process thoroughly and complete each step. If the condition exhibited is resolved without completing every step, the
remaining steps do not need to be performed. If these steps do not resolve the condition.
Data Link Communications
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 120
Chevrolet Venture V6-3.4L VIN E 1800

Diagnostic Chart (Part 1 of 2)


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 121
Chevrolet Venture V6-3.4L VIN E 1801

Diagnostic Chart (Part 2 of 2)

CIRCUIT DESCRIPTION
Modules connected to the class 2 serial data circuit monitor for serial data communications during normal vehicle operation. Operating
information and commands are exchanged among the modules. When a module receives a message for a critical operating parameter, the module
records the identification number of the module which sent the message for State of Health monitoring. A critical operating parameter is one
which, when not received, requires that the module use a default value for that parameter. When a module does not associate an identification
number with at least one critical parameter within about five seconds of beginning serial data communication, DTC U1000 or U1255 is set.
When more than one critical parameter does not have an identification number associated with it, the DTC will only be reported once.

CONDITIONS FOR RUNNING THE DTC


^ Voltage supplied to the module is in the normal operating voltage range (approximately 9 to 16 volts).
^ Diagnostic trouble codes U1300 and U1301 and U1305 do not have a current status.
^ The vehicle power mode (ignition switch position) requires serial data communication to occur.

CONDITIONS FOR SETTING THE DTC


At least one critical operating parameter has not been associated with an identification number within about five seconds after beginning serial
data communication.

ACTION TAKEN WHEN THE DTC SETS


The module uses a default value for the missing parameter.

CONDITIONS FOR CLEARING THE DTC


^ A current DTC U1000 or U1255 will clear when all critical operating parameters for the module have been associated with an identification
number or at the end of the current ignition cycle.
^ A history DTC U1000 or U1255 will clear upon receipt of a scan tool Clear DTCs command.

DIAGNOSTIC AIDS
When a malfunction (such as an open fuse to a module) occurs while modules are communicating, a Lost Communication DTC is set as a current
DTC. When the modules stop communicating (ignition is turned OFF) the current Lost Communication DTC is cleared but the history DTC
remains. When the modules begin to communicate again, the module with the open fuse will not be learned by the other modules so DTC U1000
or U1255 is set current by the other modules. If the malfunction occurs when the modules are not communicating, only DTC U1000 or U1255 is
set.

TEST DESCRIPTION
The number(s) below refer to the step number(s) on the diagnostic table.
1. A Lost Communication with XXX DTC with a history status may indicate the cause of U1000 or U1255.
2. The module(s) which is not communicating is the likely cause of U1000 or U1255 being set. The following modules communicate on the
class 2 serial data circuit:
^ PCM
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 122
Chevrolet Venture V6-3.4L VIN E 1802
^ EBCM
^ SDM
^ IPC
^ PK3
^ DID
^ Radio
5. The module which was not communicating may have set Lost Communication with XXX DTCs for those modules that it was monitoring.
6. The module which was not communicating may have set Lost Communication with XXX DTCs for those modules that it was monitoring.
7. The module which was not communicating may have set Lost Communication with XXX DTCs for those modules that it was monitoring.
11. The modules which can communicate indicate the module which cannot communicate. You must clear the DTC from these modules to avoid
future misdiagnosis.
13. If all modules are communicating, the module which set U1000 or U1255 may have done so due to some other condition.
14. The module which set U1000 or U1255 is the likely cause of the malfunction.

U1300
CIRCUIT DESCRIPTION
Modules connected to the class 2 serial data circuit monitor for serial data communications during normal vehicle operation. Operating
information and commands are exchanged among the modules. In addition to this, Node Alive (State of Health) messages are transmitted by each
module on the class 2 serial data circuit about once every two seconds. When the module detects no messages and a low voltage on the class 2
serial data circuit for approximately three seconds, U1300 is set. The setting of all other class 2 serial communication DTCs is inhibited.

CONDITIONS FOR RUNNING THE DTC


^ Voltage supplied to the module is in the normal operating voltage range (approximately 9 - 16 volts).
^ The vehicle power mode (ignition switch position) requires serial data communication to occur.

CONDITIONS FOR SETTING THE DTC


^ No valid messages are detected on the class 2 serial data circuit.
^ The voltage level detected on the class 2 serial data circuit is low.
^ The above conditions are met for approximately three seconds.

ACTION TAKEN WHEN THE DTC SETS


^ The module inhibits the setting of all other class 2 DTCs.
^ The module uses default values for all parameters received on the class 2 serial data circuit.

CONDITIONS FOR CLEARING THE DTC


^ A U1300 will clear when a valid class 2 message is detected on the class 2 serial data circuit or at the end of the current ignition cycle.
^ A history U1300 will clear upon receipt of a scan tool Clear DTCs command.

DIAGNOSTIC AIDS
^ This DTC cannot be retrieved with a current status. Diagnosis of an U1300 is accomplished via the symptom, Scan Tool Does Not
Communicate with Class 2 Device.
^ An intermittent condition is likely to be caused by a short to ground on the class 2 serial data circuit. Refer to Scan Tool Does Not
Communicate with Class 2 Device in order to isolate an intermittent condition.

U1301
CIRCUIT DESCRIPTION
Modules connected to the class 2 serial data circuit monitor for serial data communications during normal vehicle operation. Operating
information and commands are exchanged among the modules. In addition to this, Node Alive (State of Health) messages are transmitted by each
module on the class 2 serial data circuit about once every two seconds. When the module detects no messages and a low voltage on the class 2
serial data circuit for approximately three seconds, U1300 is set. The setting of all other class 2 serial communication DTCs is inhibited.

CONDITIONS FOR RUNNING THE DTC


^ Voltage supplied to the module is in the normal operating voltage range (approximately 9 - 16 volts).
^ The vehicle power mode (ignition switch position) requires serial data communication to occur.

CONDITIONS FOR SETTING THE DTC


^ No valid messages are detected on the class 2 serial data circuit.
^ The voltage level detected on the class 2 serial data circuit is low.
^ The above conditions are met for approximately three seconds.

ACTION TAKEN WHEN THE DTC SETS


^ The module inhibits the setting of all other class 2 DTCs.
^ The module uses default values for all parameters received on the class 2 serial data circuit.

CONDITIONS FOR CLEARING THE DTC


^ A U1300 will clear when a valid class 2 message is detected on the class 2 serial data circuit or at the end of the current ignition cycle.
^ A history U1300 will clear upon receipt of a scan tool Clear DTCs command.

DIAGNOSTIC AIDS
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 123
Chevrolet Venture V6-3.4L VIN E 1803
^ This DTC cannot be retrieved with a current status. Diagnosis of an U1300 is accomplished via the symptom, Scan Tool Does Not
Communicate with Class 2 Device.
^ An intermittent condition is likely to be caused by a short to ground on the class 2 serial data circuit. Refer to Scan Tool Does Not
Communicate with Class 2 Device in order to isolate an intermittent condition.

U1305
CIRCUIT DESCRIPTION
Modules connected to the class 2 serial data circuit monitor for serial data communications during normal vehicle operation. Operating
information and commands are exchanged among the modules. In addition to this, Node Alive (State of Health) messages are transmitted by each
module on the class 2 serial data circuit about once every two seconds. When the module detects no messages on the class 2 serial data circuit
for approximately three seconds, U1305 is set and the setting of all other class 2 serial communication DTCs is inhibited.

CONDITIONS FOR RUNNING THE DTC


^ Voltage supplied to the module is in the normal operating voltage range (approximately 9 to 16 volts).
^ The vehicle power mode (ignition switch position) requires serial data communication to occur.

CONDITIONS FOR SETTING THE DTC


^ No valid class 2 messages are detected on the class 2 serial data circuit.
^ The above condition is met for approximately three seconds.

ACTION TAKEN WHEN THE DTC SETS


^ The module inhibits the setting of all other class 2 DTCs.
^ The module uses default values for all parameters received on the class 2 serial data circuit.

CONDITIONS FOR CLEARING THE DTC


^ A current U1305 will clear when a valid class 2 message is detected on the class 2 serial data circuit or at the end of the current ignition
cycle.
^ A history U1305 will clear upon receipt of a scan tool Clear DTCs command.

DIAGNOSTIC AIDS
^ This DTC cannot be retrieved with a current status. The diagnosis of U1305 is accomplished via the symptom, Scan Tool Does Not
Communicate with a Class 2 Device. Refer to Scan Tool Does Not Communicate with Class 2 Device.
^ An intermittent condition is likely to be caused by a short to ground or voltage on the class 2 serial data circuit. Use the Scan Tool Does Not
Communicate with a Class 2 Device procedure in order to isolate an intermittent condition. Refer to Scan Tool Does Not Communicate with
Class 2 Device.

DTC 001
DTC 1 Fasten Seat Belt Indicator Control Circuit Shorted B+ or Ground

Schematic

CIRCUIT DESCRIPTION
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 124
Chevrolet Venture V6-3.4L VIN E 1804
The Body Control Module (BCM) controls the operation of the seat belt indicator. The seat belt indicator is located in the instrument cluster. The
BCM turns ON the seat belt indicator by sending voltage through the seat belt indicator supply voltage circuit. The seat belt indicator receives
ground through the ground circuit.

The BCM turns ON the seat belt indicator for 55 seconds when the following conditions are met:
^ The ignition switch is ON
^ The driver's seat belt releases (unfastens).

If the driver's seat belt is fastened during the 55 second period, the BCM turns OFF the seat belt indicator. If the driver's seat belt releases
anytime during the same ignition cycle, the BCM turns ON the seat belt indicator again for 55 seconds.

CONDITIONS FOR RUNNING THE DTC


Ignition voltage is within the normal operating voltage range.

CONDITIONS FOR SETTING THE DTC


The BCM detects a short to B+ or ground in the seat belt indicator supply voltage circuit.

ACTION TAKEN WHEN THE DTC SETS


^ The seat belt indicator lamp does not turn on when the seat belt indicator supply voltage circuit shorts to ground.
^ The seat belt indicator lamp stays on at all times when the seat belt indicator supply voltage circuit shorts to B+.

CONDITIONS FOR CLEARING THE DTC


^ A short to B+ or ground in the seat belt indicator supply voltage circuit is no longer present between the BCM and the instrument cluster.
^ After you complete the repairs, clear the DTC. Refer to Diagnostic Trouble Code (DTC) Clearing.

DIAGNOSTIC AIDS
^ Inspect for a short to ground in the seat belt indicator supply voltage circuit.
^ Inspect for a short to B+ in the seat belt indicator supply voltage circuit.
^ Inspect for an internal short to ground or short to B+ within the instrument cluster circuity.

TEST DESCRIPTION
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 125
Chevrolet Venture V6-3.4L VIN E 1805

Diagnostic Chart

The number(s) below refer to the step number(s) on the diagnostic table.
2. This step determines if there is a short to ground or a short to B+ in the seat belt indicator supply voltage circuit.
3. This step determines if there is a short to B+ in the seat belt indicator supply voltage circuit or if there is a malfunctioning BCM.
5. This step determines if there is a short to B+ in the seat belt indicator supply voltage circuit or if there is a malfunctioning instrument cluster.
8. This step determines if there is a short to ground in the seat belt indicator supply voltage circuit or if there is a malfunctioning instrument
cluster.

DTC 002
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 126
Chevrolet Venture V6-3.4L VIN E 1806

Schematic
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 127
Chevrolet Venture V6-3.4L VIN E 1807

Diagnostic Chart (Part 1 of 2)


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 128
Chevrolet Venture V6-3.4L VIN E 1808

Diagnostic Chart (Part 2 of 2)

CIRCUIT DESCRIPTION
The Body Control Module (BCM) controls the inadvertent load (battery rundown) protection feature. The BCM de-energizes circuit 1393 and
circuit 328 nine to eleven minutes after the ignition switch has been turned from the ACC position or the RUN position to the LOCK position or
the OFF position. The BCM restores power to circuit 1393 and circuit 328 when the following actions occur:
- The ignition switch is turned from the LOCK position or the OFF position to the ACC position or the RUN position.
- The key is removed from the ignition.
- Any vehicle door is opened.
- The instrument panel dimmer switch is turned to the DOME position.
- Any interior courtesy light connected to circuit 1393 and circuit 328 is turned on.
- The BCM receives a message to unlock the doors from the Remote Control Door Lock Receiver (BCM type 3 or type 4 only).
- A door is unlocked using a key (BCM type 4 only).

The inadvertent load (battery rundown) protection feature is mileage-sensitive. Vehicles with less than 15 total driven miles have a time-out of
162-198 seconds instead of 10 minutes.

CONDITIONS FOR SETTING THE DTC


The BCM detects a short to B+ or ground in circuit 1393 or circuit 328.

ACTION TAKEN WHEN THE DTC SETS


- The BCM sets the Diagnostic Trouble Code (DTC) 2.
- The inadvertent load (battery rundown) protection feature is disabled when circuit 1393 or circuit 328 is shorted to B+.
- The interior courtesy lights do not turn on when circuit 1393 or circuit 328 is shorted to ground.

CONDITIONS FOR CLEARING THE MIL/DTC


- A short to B+ or ground in circuit 1393 or circuit 328 is no longer present.
- After you complete the repairs, refer to Diagnostic Trouble Code (DTC) Clearing in order to clear the DTC.

DIAGNOSTIC AIDS
- Inspect for a short to B+ in circuit 1393 and circuit 328.
- Inspect for a short to ground in circuit 1393 and circuit 328.

TEST DESCRIPTION
The numbers below refer to the step numbers on the diagnostic table.
1. Always perform the lighting diagnostic system check before attempting to diagnose the DTC.
2. Tests circuit 1393 for a short to ground.
4. Tests circuit 328 for a short to ground.
6. Tests circuit 328 for a short to B+.
8. Tests circuit 1393 for a short to B+.

DTC 003
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 129
Chevrolet Venture V6-3.4L VIN E 1809

Diagnostic Chart

Schematic

CIRCUIT DESCRIPTION
The Body Control Module (BCM) controls the interior illumination. The BCM turns on the interior (courtesy) lamps when the following actions
occur:
- Any of the vehicle doors are opened.
- The instrument panel dimmer switch is turned to the DOME position.
- Exit illumination is active.
- The doors are unlocked through the keyless entry system (BCM type 3 and type 4 only).
- The doors are unlocked using the door key cylinder (BCM type 4 only).

The BCM turns the interior lamps off when all the vehicle doors are closed and the instrument panel dimmer switch is in the OFF position.
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 130
Chevrolet Venture V6-3.4L VIN E 1810

All the vehicle doors contain a door lock ajar switch. When the driver door is open, the left front door lock ajar switch closes and sends a ground
signal to the BCM through circuit 159.

When one of the right front, left rear, or right rear doors is open, its corresponding door lock ajar switch closes and sends a ground signal to the
BCM through circuit 54.The BCM grounds circuit 690 when detecting a ground signal in any of the following circuits:
- circuit 49
- circuit 54
- circuit 159

When the driver door is closed, the left front door lock ajar switch opens circuit 159. When all of the right front, left rear, and right rear doors are
closed, their corresponding door lock ajar switches open circuit 49. The BCM then opens circuit 690 when any one of circuits 49, 54, or 159 is
open.

The BCM uses the voltage in circuit 240 to power the interior lights through circuit 328 and circuit 1393.The BCM controls the power supplied
to circuit 328 and circuit 1393 for inadvertent load (battery rundown) protection. The BCM opens circuit 690 when the inadvertent battery power
rundown protection is active (circuit 1393 is open).

CONDITIONS FOR SETTING THE DTC


The BCM detects a short to B+ in circuit 690.

ACTION TAKEN WHEN THE DTC SETS


- The BCM sets the Diagnostic Trouble Code (DTC) 3.
- The interior courtesy lamps do not illuminate.

CONDITIONS FOR CLEARING THE MIL/DTC


- A short to B+ in circuit 690 is no longer present between the BCM and any of the courtesy lamps.
- After the repairs are completed, clear the DTC. Refer to Diagnostic Trouble Code (DTC) Clearing.

DIAGNOSTIC AIDS
Inspect for a short to B+ in circuit 690.

Interior Lighting Modes


Perform the following procedure in order to change the interior lighting mode:
1. Turn off the instrument panel dimmer switch.
2. Turn the ignition switch to the OFF position.
3. Remove the MALL PGM fuse.
4. Turn the ignition switch to the ACC position.

The BCM sounds the chime a number of times equivalent to the BCM type installed on the vehicle. At this time the BCM has entered the feature
customization mode. In order to change the interior lighting, cycle the IP dimmer switch from the OFF position to the DOME position and then
back to the OFF position. The BCM sounds a chime a number of times equal to the lighting mode.

The lighting modes are as follows:


- Mode 1 - Exit illumination and delayed illumination are disabled.
- Mode 2 - Delay illumination is enabled.
- Mode 3 - Exit illumination is enabled.
- Mode 4 - Exit illumination and delayed illumination are enabled.

TEST DESCRIPTION
The numbers below refer to the step numbers on the diagnostic table.
1. Always perform the lighting diagnostic system check before attempting to diagnose DTC 3.
2. Tests for a short to B+ in circuit 690.

DTC 006
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 131
Chevrolet Venture V6-3.4L VIN E 1811

Diagnostic Chart
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 132
Chevrolet Venture V6-3.4L VIN E 1812

Schematics

CIRCUIT DESCRIPTION
The Body Control Module (BCM) type 4 activates the headlamps and the horn when any of the following occurs:
^ The message received from the keyless entry system's Remote Control Door Lock Receiver (RCDLR) in order to perform the alarm mode.
^ The BCM detects a theft attempt when the content theft deterrent is in either the armed or warning mode.
^ The theft deterrent system is in the trunk open mode.

The BCM interfaces with the headlamps through the theft deterrent relay. The theft deterrent relay allows the BCM to turn the headlamps ON
providing a visual alert. The BCM energizes the theft deterrent relay, turning the headlamps ON by grounding circuit 301 during the following
modes:
^ The armed mode-When the content theft deterrent is in the armed mode, the BCM turns the headlamps ON once for 950-1000 ms. The BCM
turns on the headlamps only if the remote activation verification is in either mode 2, 3 or 4. Refer to Diagnostic Aids. The horn also sounds
during this mode. The BCM will sound the horn first then the headlamps will flash.
^ The warning mode-The warning mode attempts to warn away potential intruders prior to setting off the alarm mode. The headlamps will
cycle ON and OFF 5 times at a rate of .09-1.1 hz with a 15-25% active state duty cycle. The horn will sound 5 times during this mode
although the BCM alternates between the horn and the headlamps.
^ The alarm mode-When the content theft deterrent is in the alarm mode, the BCM will turn the headlamps ON and OFF for 2 minutes or until
the alarm is disarmed at a rate of 9.0-1.1 hz with a 15-25% active state duty cycle. The horn will sound during this mode although the BCM
alternates between the horn and the exterior lights.

CONDITIONS FOR SETTING THE DTC


The BCM detects a short to B+ or ground in circuit 301.

ACTION TAKEN WHEN THE DTC SETS


^ The BCM sets the diagnostic trouble code (DTC) 6.
^ The BCM does not turn on the headlamps during the armed, warning, alarm or trunk open modes.
^ If circuit 301 is shorted to ground, the headlamps will stay ON at all times.

CONDITIONS FOR CLEARING THE MIL/DTC


^ A short to B+ or ground in circuit 301 is no longer present between the BCM and the theft deterrent relay.
^ After the repairs are completed, refer to Diagnostic Trouble Code (DTC) Clearing for the DTC clearing procedure.

DIAGNOSTIC AIDS
^ Inspect for a short to B+ or ground in circuit 301.
^ A faulty theft deterrent relay.
^ Perform the following test while moving the wiring and connectors. This will cause the malfunction to appear.

REMOTE ACTIVATION VERIFICATION MODES


Perform the following procedure in order to change the remote activation verification mode:
1. Turn the instrument panel dimmer switch OFF.
2. Turn the ignition switch to the LOCK position.
3. Remove the BCM PRGRM fuse.
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 133
Chevrolet Venture V6-3.4L VIN E 1813
4. Turn the ignition switch to the ACC position.
^ The BCM will sound a chime the number of times equivalent to the BCM type installed on the vehicle.
^ The BCM has entered the feature customization mode.
^ In order to change the remote activation verification mode, press the lock button on the keyless entry transmitter.
^ The BCM will sound a chime the number of times equivalent to the remote activation verification mode.

The following are the remote activation verification modes:


^ Mode 1-The remote activation verification is disabled. No horn or headlamps.
^ Mode 2-The headlamps will flash when locking/unlocking the doors with the keyless entry transmitter.
^ Mode 3-The headlamps will flash when unlocking the doors with the keyless entry transmitter. The headlamps will flash and the horn
will sound when locking the doors with the keyless entry transmitter.
^ GMode 4-The headlamps will flash when unlocking/locking the doors with the keyless entry transmitter. The headlamps will flash and
the horn will sound when locking the doors with the keyless entry transmitter a second time within 5 seconds of locking the doors with
the keyless entry transmitter.

TEST DESCRIPTION
The number(s) below refer to the step number(s) on the diagnostic table.
1. Always perform the theft deterrent diagnostic system check before attempting to diagnose the DTC.
2. Tests for a short to B+ in circuit 301
3. Tests for a short to ground in circuit 301
4. Tests for a faulty theft deterrent relay.

DTC 007

Diagnostic Chart
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 134
Chevrolet Venture V6-3.4L VIN E 1814

Schematic

CIRCUIT DESCRIPTION
The vehicle horns are activated whenever ground is applied to the horn relay coil through circuit 28. Ground may be applied to the relay coil by
either of the following methods:
- The Body Control Module (BCM) (with UA6 only)
- The horn switch

CONDITIONS FOR SETTING THE DTC


The BCM detects a short to B+ or ground in circuit 28.

ACTION TAKEN WHEN THE DTC SETS


- The BCM sets the diagnostic trouble code DTC 7.
- If circuit 28 is shorted to B+, the horns are inoperative.
- If circuit 28 is shorted to ground, the horns will sound all the time.

CONDITIONS FOR CLEARING THE MIL/DTC


- A short to B+ or ground in circuit 28 is no longer present between the BCM and the horn relay.
- After the repairs are completed, refer to Diagnostic Trouble Code (DTC) Clearing in order to clear the DTC.

DIAGNOSTIC AIDS
Inspect for a short to B+ or ground in circuit 28.

TEST DESCRIPTION
The numbers below refer to the step numbers on the diagnostic table.
1. Always perform the horns diagnostic system check before attempting to diagnose DTC 7.
2. Inspects for a short to B+ in circuit 28.
3. Inspects for a short to ground in circuit 28.
4. Circuit 28 includes the horn slip ring and the horn switch. The horn switch is part of the inflatable restraint steering wheel module. The slip
ring and switch must be tested for a short to B+ when testing circuit 28. Refer to Circuit Testing and Wiring Repairs in Diagrams and
Inflatable Restraint Steering Wheel Module Replacement in SIR.
5. Circuit 28 includes the horn slip ring and the horn switch. The horn switch is part of the inflatable restraint steering wheel module. The slip
ring and switch must be tested for a short to ground when testing circuit 28. Refer to Circuit Testing and Wiring Repairs in Diagrams and
Inflatable Restraint Steering Wheel Module Replacement in SIR.

For a description of the RPO Code(s) shown in this article, refer to the RPO Code List found at Vehicle/Application and ID. See: Application and
ID
DTC 008
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 135
Chevrolet Venture V6-3.4L VIN E 1815

Diagnostic Chart
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 136
Chevrolet Venture V6-3.4L VIN E 1816

Schematic

CIRCUIT DESCRIPTION
The Remote Control Door Lock Receiver (RCDLR) communicates with the Body Control Module (BCM) through the keyless entry serial data
circuit. When any button on the keyless entry transmitter is pressed, the transmitter sends a signal to the RCDLR. The RCDLR sends either a
lock or unlock request to the BCM, depending on which button is pressed on the transmitter.

The BCM receives the message and performs the appropriate function.

CONDITIONS FOR SETTING THE DTC


The BCM detects an open, a short to voltage, or a short to ground in the keyless entry serial data circuit.

ACTION TAKEN WHEN THE DTC SETS


^ The BCM sets the Diagnostic Trouble Code (DTC) 8.
^ The keyless entry system remains inoperative. The power sliding door may still be operational because the RCDLR operates the power
sliding door directly without using the BCM.

CONDITIONS FOR CLEARING THE MIL/DTC


^ An open, a short to voltage, or a short to ground in the keyless entry serial data circuit is no longer present between the BCM and the
RCDLR.
^ After the repairs are completed, refer to Diagnostic Trouble Code (DTC) Clearing in order to clear the DTC.

DIAGNOSTIC AIDS
Refer to Testing for Intermittent and Poor Connections in Diagrams.

TEST DESCRIPTION
The numbers below refer to the step numbers on the diagnostic table.
1. Always perform the keyless entry diagnostic system check before attempting to diagnose DTC 8.
2. This step tests for B+ on the keyless entry serial data circuit.
3. This step tests the keyless entry serial data circuit for a short to voltage.
4. This step tests the keyless entry serial data circuit for a high resistance or an open.
5. This step tests the keyless entry serial data circuit for a short to ground.

DTC 013
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 137
Chevrolet Venture V6-3.4L VIN E 1817

Diagnostic Chart (Part 1 of 3)


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 138
Chevrolet Venture V6-3.4L VIN E 1818

Diagnostic Chart (Part 2 of 3)


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 139
Chevrolet Venture V6-3.4L VIN E 1819

Diagnostic Chart (Part 3 of 3)

Schematic

CIRCUIT DESCRIPTION
The Power Sliding Door (PSD) contains an optical sensor that provides sliding door position information to the rear side door actuator control
module. The optical sensor sends pulses to the rear side door actuator control module when the sliding door is moving. The rear side door
actuator control module keeps track of these optical sensor pulses at all times, even when the sliding door is open or closed manually with the
power sliding door on/off switch in the off position. The optical sensor pulses allow the rear side door actuator control module to calculate the
position of the sliding door. Also, the optical sensor allows the rear side door actuator control module to resume PSD operation after operating
the sliding door manually.

In addition to the optical sensor, the rear side door actuator control module uses the PSD detent switch to determine when the sliding door is
open, ajar, or latched. The PSD detent switch is part of the sliding door latch assembly. The PSD detent switch sends ground signals to the rear
side door actuator control module through circuit 1892 indicating when the sliding door is open, ajar, or latched (fully closed). The PSD detent
switch receives ground through circuit 750. Circuits 750 and 1892 pass through the switch plate plungers and pads located on the B-pillar.

When the PSD is closing and the sliding door is about 30 cm (12 in.) from being closed, the rear side door actuator control module reduces
power to the cable motor. This action slows down the movement of the sliding door. Once the switch plate plungers and pads make contact,
circuits 750 and 1892 are completed and the rear side door actuator control module is able to monitor the PSD detent switch input.
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 140
Chevrolet Venture V6-3.4L VIN E 1820

When the sliding door latch moves from the open to the secondary latch (ajar) position, the PSD detent switch no longer sends a ground signal to
the rear side door actuator control module, thus opening circuit 1892. This action signals the rear side door actuator control module that the
sliding door has passed from the open door to the secondary latch (ajar) position. Upon detecting the door ajar position, the rear side door
actuator control module sends full power to the cable motor.

As the sliding door continues to close, the sliding door latch moves from the ajar to the primary latch position. The PSD detent switch sends and
another ground signal to the rear side door actuator control module when the sliding door is between the secondary and primary latch position.
This action signals the rear side door actuator control module that the sliding door has passed from ajar to door closed position. Then, the rear
side door actuator control module disengages the clutch and de-energizes the cable motor.

CONDITIONS FOR SETTING THE DTC


The PSD is unable to determine the exact location of the sliding door due to a problem with one of the following inputs:
^ The optical sensor input
^ The PSD detent switch input

ACTION TAKEN WHEN THE DTC SETS


^ The PSD is disabled.
^ Any PSD movement, if in process is stopped.
^ The rear side door actuator control module sets DTC 13 in memory.

CONDITIONS FOR CLEARING THE DTC


^ The Conditions for Setting the DTC are no longer present.
^ The power sliding door is re-initialized.

DIAGNOSTIC AIDS
^ Inspect for the following conditions:
- Poor connector terminal contact at the rear side door actuator control module
- Poor interface of switch plate plungers and striker
- An open in circuit 1892
- An open in circuit 750
- Poor ground, G302
- A short to ground in circuit 1892
- A faulty PSD detent switch
^ Prevent bright light from reaching the optical sensor when performing diagnostics with the rear quarter trim panel removed. Bright light may
cause the rear side door actuator control module to lose track of the sliding door position.
^ An intermittent failure may be difficult to detect and to accurately diagnose. Faulty electrical connections or wiring causes most intermittent
problems. When an intermittent condition is suspected, inspect the suspected circuits for the following conditions:
- Poor mating of connector halves
- Backed out terminals
- Improperly formed or damaged terminals
- Wire chafing
- Poor wire-to-terminal connections
- Dirty or corroded terminals
- Damaged connector bodies
- A broken wire inside the insulation
^ Use a J 35616-A whenever a diagnostic procedure requests probing or inspecting a terminal. Using the J 35616-A ensures that no damage to
the terminal will occur. Using the J 35616-A provides an estimate of whether the contact tension is sufficient.

TEST DESCRIPTION
The number(s) below the step number(s) on the diagnostic table.
2. This step performs the Diagnostic Mode 2: Input Test.
3. This step determines if the malfunction is in the sliding door or in the vehicle.
4. This step tests for an open in circuit 750 (door side).
5. This step tests for an open in circuit 1892 (door side).
6. This step determines if circuit 1892 is shorted to ground (door side) or the PSD detent switch is faulty.
7. This step tests for an open in circuit 750 (vehicle side).
8. This step tests for a short to ground in circuit 1892 (vehicle side).
9. This step tests for an open in circuit 1892 (vehicle side).
17. This step determines if the malfunction is intermittent or the rear side door actuator control module is faulty.

DTC 014
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 141
Chevrolet Venture V6-3.4L VIN E 1821

Diagnostic Chart

CIRCUIT DESCRIPTION
The Power Sliding Door (PSD) contains a microprocessor-based control module. The rear side door actuator control module monitors the inputs
from the following components:
^ The PSD on/off switch
^ The overhead console PSD open/close switch
^ The RH B-pillar PSD open/close switch
^ The PARK position of the transaxle range switch
^ The ignition switch
^ The keyless entry system's Remote Control Door Lock Receiver (RCDLR)

The rear side door actuator control module determines the position of the sliding door through the following components:
^ The PSD detent switch
^ The optical sensor

Based on these inputs, the rear side door actuator control module sends outputs to the following components:
^ The cable motor
^ The clutch
^ The unlatch actuator
^ The PSD alarm

CONDITIONS FOR SETTING THE DTC


The DTC identifies that a fault is present in the rear side door actuator control module.

ACTION TAKEN WHEN THE DTC SETS


The PSD is disabled.
The rear side door actuator control module sets DTC 14 in memory.

CONDITIONS FOR CLEARING THE DTC


^ The condition for setting the DTC is no longer present.
^ The power sliding door is re-initialized.

DIAGNOSTIC AIDS
An Intermittent failure may be difficult to detect and to accurately diagnose. Faulty electrical connections or wiring causes most Intermittent
problems. When an Intermittent condition is suspected, inspect the suspected circuits for the following conditions:
^ Poor mating of connector halves
^ Backed out terminals
^ Improperly formed or damaged terminals
^ Wire chafing
^ Poor wire-to-terminal connections
^ Dirty or corroded terminals
^ Damaged connector bodies
^ A broken wire inside the insulation

TEST DESCRIPTION
The number(s) below the step number(s) on the diagnostic table.
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 142
Chevrolet Venture V6-3.4L VIN E 1822
2. This step performs Diagnostic Mode 1: Reading DTCs.

DTC 022

Diagnostic Chart

Schematic
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 143
Chevrolet Venture V6-3.4L VIN E 1823
CIRCUIT DESCRIPTION
The Power Sliding Door (PSD) contains an optical sensor that provides sliding door position information to the rear side door actuator control
module. The optical sensor sends pulses to the rear side door actuator control module when the sliding door is moving. The rear side door
actuator control module keeps track of these optical sensor pulses at all times, even when the sliding door is opened or closed manually with the
power sliding door on/off switch in the off position. The optical sensor pulses allow the rear side door actuator control module to calculate the
position of the sliding door. Also, the optical sensor allows the rear side door actuator control module to resume PSD operation after operating
the sliding door manually.

CONDITIONS FOR SETTING THE DTC


The rear side door actuator control module does not detect the optical sensor pulses during a PSD open or close operation.

ACTION TAKEN WHEN THE DTC SETS


The rear side door actuator control module sets DTC 22 in memory.

CONDITIONS FOR CLEARING THE DTC


^ The conditions for setting the DTC are no longer present.
^ The power sliding door is re-initialized.

DIAGNOSTIC AIDS
^ inspect for the following conditions:
- An open in circuit 340
- Poor connector terminal contact in the PSD electrical connectors
- A faulty rear side door actuator motor assembly
^ Prevent bright light from reaching the optical sensor when performing diagnostics with the rear quarter trim panel removed. Bright light may
cause the rear side door actuator control module to be unable to monitor the sliding door position.
^ An Intermittent failure may be difficult to detect and to accurately diagnose. Faulty electrical connections or wiring causes most Intermittent
problems. When an Intermittent condition is suspected, inspect the suspected circuits for the following conditions:
- Poor mating of connector halves
- Backed out terminals
- Improperly formed or damaged terminals
- Wire chafing
- Poor wire-to-terminal connections
- Dirty or corroded terminals
- Damaged connector bodies
- A broken wire inside the insulation
^ Use a J 35616-A whenever a diagnostic procedure requests probing or inspecting a terminal. Using the J 35616-A ensures that no damage to
the terminal will occur. Using the J 35616-A provides an estimate of whether the contact tension is sufficient.

TEST DESCRIPTION
The number(s) below the step number(s) on the diagnostic table.
2. This step tests for an open in circuit 340.
3. This step determines if the DTC set due to a poor electrical connection and not because of a faulty rear side door actuator control module.

DTC 023
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 144
Chevrolet Venture V6-3.4L VIN E 1824

Diagnostic Chart (Part 1 of 3)


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 145
Chevrolet Venture V6-3.4L VIN E 1825

Diagnostic Chart (Part 2 of 3)


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 146
Chevrolet Venture V6-3.4L VIN E 1826

Diagnostic Chart (Part 3 of 3)

Schematic

CIRCUIT DESCRIPTION
The rear side door actuator control module uses the PSD detent switch to determine when the sliding door is open, ajar, or latched. The PSD
detent switch is part of the sliding door latch assembly. The PSD detent switch sends ground signals to the rear side door actuator control module
through circuit 1892 indicating when the sliding door is open, ajar, or latched (fully closed). The PSD detent switch receives its ground through
circuit 750. Circuits 750 and 1892 are completed through the switch plate plungers and pads located on the B-pillar. When the PSD is closing
and the sliding door is about 30 cm (12 in.) from being closed, the rear side door actuator control module reduces power to the cable motor. This
action slows down the movement of the sliding door. Once the switch plate plungers and pads make contact, circuits 750 and 1892 are completed
and the rear side door actuator control module is able to monitor the door lock latch switch input.
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 147
Chevrolet Venture V6-3.4L VIN E 1827

When the sliding door latch moves from the open to the secondary latch (ajar) position, the PSD detent switch no longer sends a ground signal to
the rear side door actuator control module, thus opening circuit 1892. This action signals the rear side door actuator control module that the
sliding door has passed from the open door to the secondary latch (ajar) position. Upon detecting the door ajar position, the rear side door
actuator control module sends full power to the cable motor.

As the sliding door continues to close, the sliding door latch moves from the ajar to the primary latch position. The PSD detent switch sends
another ground signal to the rear side door actuator control module when the sliding door is between the secondary and primary latch position.
This action signals the rear side door actuator control module that the sliding door has passed from ajar to door closed position. Then, the rear
side door actuator control module disengages the clutch and de-energizes the cable motor.

CONDITIONS FOR SETTING THE DTC


^ The PSD has reached the full close (latched) position.
^ The PSD detent switch has not sent a toggle signal.

ACTION TAKEN WHEN THE DTC SETS


^ The PSD will not power open using door handle.
^ The PSD is allowed to power open and close using open/close switch(es).
^ The rear side door actuator control module sets DTC 23 in memory.
^ The PSD alarm will sound when the transaxle is shifted out of PARK.

CONDITIONS FOR CLEARING THE DTC


DTC 23 clears anytime the following actions occur:
^ The sliding door is manually closed.
^ The PSD controller receives a valid ground signal for secondary and primary latch positions from the detent switch.

DIAGNOSTIC AIDS
^ Perform the following:
^ Check the door rods/latch: Inspect, adjust or replace the door lock rods and linkage. Lock Rod Adjustment - Sliding Door. Also, inspect,
adjust or replace the rear latch. Lock Replacement - Sliding Door Rear.
^ Repair the electrical noise: Check the pads/plungers for secure attachment to body/door; replace pouch in fasteners if necessary. Check of
corrosion, water entry, dirty or sticking plungers; clean or replace plungers. Check ground circuits. Check the detent switch; replace if
necessary.
^ Check the adjustment of the sliding door. Door Up/Down Adjustment - Sliding for up/down adjustment, Door Front Edge In/Out
Adjustment - Sliding for door front edge in/out adjustment, or Door Rear Edge In/Out Adjustment - Sliding for door rear edge in/out
adjustment.
^ Inspect for the following conditions:
- Good interface of switch plate plungers and pads
- An open in circuit 1892
- An open in circuit 750
- Poor G302
- A short to ground in circuit 1892
- A faulty PSD detent switch
^ An Intermittent failure may be difficult to detect and to accurately diagnose. Faulty electrical connections or wiring causes most Intermittent
problems. When an Intermittent condition is suspected, inspect the suspected circuits for the following conditions:
- Poor mating of connector halves
- Backed out terminals
- Improperly formed or damaged terminals
- Wire chafing
- Poor wire-to-terminal connections
- Dirty or corroded terminals
- Damaged connector bodies
- A broken wire inside the insulation
- Does not latch to primary (AJAR)
- Door almost closes then releases to full open
^ Use a J 35616-A whenever a diagnostic procedure requests probing or inspecting a terminal. Using the J 35616-A ensures that no damage to
the terminal will occur. Using the J 35616-A provides an estimate of whether the contact tension is sufficient.

TEST DESCRIPTION
The number(s) below the step number(s) on the diagnostic table.
2. This step performs the Diagnostic Mode 2: Input Test.
3. This step determines if the malfunction is in the sliding door or in the vehicle.
4. This step tests for an open in circuit 750 (door side).
5. This step tests for an open in circuit 1892 (door side).
6. This step determines if circuit 1892 is shorted to ground (door side) or if the PSD detent switch is faulty.
7. This step tests for an open in circuit 750 (vehicle side).
8. This step tests for a short to ground in circuit 1892 (vehicle side).
9. This step tests for an open in circuit 1850 (vehicle side).
17. This step determines if the malfunction is Intermittent or if the PSD control module or rear side door actuator control module is faulty.
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 148
Chevrolet Venture V6-3.4L VIN E 1828

DTC 024

Diagnostic Chart

CIRCUIT DESCRIPTION
The rear side door actuator control module uses a vehicle speed signal input. While the vehicle is in motion, the powertrain control module
cycles the voltage in circuit 389 between low and high 4000 times per mile. The rear side door actuator control module uses this input in order to
determine when the vehicle is in motion.

The operator may command the Power Sliding Door (PSD) to close while the vehicle is in motion. Inertial force acting on the sliding door
caused by the vehicle's motion may reverse the sliding door. The rear side door actuator control module recognizes that the vehicle's motion may
have caused the reversal and will continue to close the sliding door.

CONDITIONS FOR SETTING THE DTC


This DTC sets if all of the following conditions are met:
^ The ignition switch is on.
^ The operator commands the PSD to open.
^ The voltage in circuit 389 is always high.

ACTION TAKEN WHEN THE DTC SETS


^ The rear side door actuator control module inhibits opening the PSD if the ignition switch is on.
^ The rear side door actuator control module permits opening the PSD if the ignition switch is off.
^ The rear side door actuator control module sets DTC 24 in memory.

CONDITIONS FOR CLEARING THE DTC


This DTC clears if all of the following conditions are met during the next ignition cycle:
^ The ignition switch is on.
^ The operator commands the power sliding door to open.
^ The voltage in circuit 389 is low.
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 149
Chevrolet Venture V6-3.4L VIN E 1829

DIAGNOSTIC AIDS
^ Inspect the system for the following conditions:
- An open in circuit 389
- Poor connector terminal contact at the rear side door actuator control module
- A faulty rear side door actuator control module
^ An Intermittent malfunction can be very difficult to diagnose accurately. Faulty electrical connections or wiring cause most of the
Intermittent conditions. If you suspect an Intermittent condition, inspect the suspect circuits for the following conditions:
- Poorly mating connector halves
- Backed-out connector terminals
- Improperly formed or damaged terminals
- Wire chafing
- Poor wire-to-terminal connections
- Dirty or corroded terminals
- Damaged connector bodies
- A wire broken inside the insulation
^ Use a J 35616-A whenever a diagnostic procedure requires probing or testing a terminal. Use this tool in order to avoid damaging the
terminal. Using this tool will help you determine if the terminal tension is sufficient.

TEST DESCRIPTION
The number(s) below refer to the step number(s) on the diagnostic table.
2. This step verifies the integrity of the vehicle speed signal.
3. This step tests for an open in circuit 389.
5. This step determines whether the malfunction is Intermittent, or the rear side door actuator control module is faulty.

DTC 032

Diagnostic Chart

CIRCUIT DESCRIPTION
The rear side door actuator control module uses a vehicle speed signal input. While the vehicle is in motion, the Powertrain Control Module (
PCM) cycles the voltage in circuit 389 between low and high 4000 times per mile. The rear side door actuator control module uses this input in
order to determine when the vehicle is in motion.

The operator may command the Power Sliding Door (PSD) to close while the vehicle is in motion. Inertial force acting on the sliding door
caused by the vehicle's motion may reverse the sliding door. The rear side door actuator control module recognizes that the vehicle's motion may
have caused the reversal and will continue to close the sliding door.
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 150
Chevrolet Venture V6-3.4L VIN E 1830

CONDITIONS FOR SETTING THE DTC


The rear side door actuator control module has not detected a high signal on circuit 389 for 5 consecutive ignition cycles.

ACTION TAKEN WHEN THE DTC SETS


^ The rear side door actuator control module inhibits opening the PSD if the ignition switch is on.
^ The rear side door actuator control module permits opening the PSD if the ignition switch is off.

CONDITIONS FOR CLEARING THE DTC


This DTC clears if all of the following conditions are met during the next ignition cycle:
^ The diagnostic mode is exited.
^ The rear side door actuator control module detects activity in circuit 389 (VSS circuit) for 10 seconds.
^ The rear side door actuator control module detects activity in circuit 389 (VSS circuit), and detects low voltage in circuit 275 (the transaxle in
PARK input).

DIAGNOSTIC AIDS
^ Inspect the system for the following conditions:
- A short to ground in circuit 389
- An open in circuit 275
- A malfunction in the transaxle range switch circuitry
- A faulty control module rear side door actuator
^ An Intermittent malfunction can be very difficult to diagnose accurately. Faulty electrical connections or wiring cause the most Intermittent
conditions. If you suspect an Intermittent condition, inspect the suspect circuits for the following conditions:
- Wire chafing
- Damaged connector bodies
^ Use a J 35616-A whenever a diagnostic procedure requires probing or testing a terminal. Use this tool in order to avoid damaging the
terminal. Using this tool will help determine if the terminal tension is sufficient.

TEST DESCRIPTION
The number(s) below refer to the step number(s) on the diagnostic table.
2. This step verifies the integrity of the vehicle speed signal.
3. This step determines whether the malfunction is Intermittent, or the rear side door actuator control module is faulty.

B0016
DTC B0016 RF/Passenger Frontal Deployment Loop (Single Stage or Stage 1) RESIST Low

Schematic

CIRCUIT DESCRIPTION
When you first turn ON the ignition, the inflatable restraint Sensing and Diagnostic Module (SDM) performs tests to diagnose critical
malfunctions within itself. Then, the SDM performs the following continuous diagnostic tests on the deployment loops:
^ Deployment loop voltage out of range test
^ Deployment loop resistance measurement test

If the voltage out of range test detects a short to voltage condition, the resistance measurement test for that deployment loop will not be performed.

CONDITIONS FOR RUNNING THE DTC


^ Ignition 1 voltage is within the normal operating voltage range.
^ Passenger frontal deployment loop is not open.
^ Passenger frontal deployment loop is not shorted to voltage.
^ Passenger frontal deployment loop is not shorted to ground.
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 151
Chevrolet Venture V6-3.4L VIN E 1831

CONDITIONS FOR SETTING THE DTC


Passenger frontal deployment loop resistance is less than 1.3 Ohms for 300 milliseconds.

ACTION TAKEN WHEN THE DTC SETS


The SDM commands ON the AIR BAG warning lamp via Class 2 serial data.

CONDITIONS FOR CLEARING THE DTC


^ You can issue a CLEAR CODES command
^ A history DTC will clear once 255 malfunction free ignition cycles have occurred

DIAGNOSTIC AIDS
The following can cause an intermittent condition:
^ A short between the passenger frontal high and the passenger frontal low circuits.
^ A malfunctioning shorting bar on the inflatable restraint IP module 2-way connector.
^ Refer to Testing for Intermittent and Poor Connections in Diagrams.

TEST DESCRIPTION
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 152
Chevrolet Venture V6-3.4L VIN E 1832

Steps 1 - 7
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 153
Chevrolet Venture V6-3.4L VIN E 1833

Steps 8 - 10

The number(s) below refer to the step number(s) on the diagnostic table.
2. This step checks the inline connector C216.
7. This step determines if there is a short between the passenger frontal high and the passenger frontal low circuits or if there is a
malfunctioning SDM.

B0017
DTC B0017 RF/Passenger Frontal Deployment Loop (Single Stage or Stage 1) Open

Schematic

CIRCUIT DESCRIPTION
When you first turn ON the ignition, the inflatable restraint Sensing and Diagnostic Module (SDM) performs tests to diagnose critical
malfunctions within itself. Then the SDM performs the following continuous diagnostic tests on the deployment loops:
^ Deployment loop voltage out of range test
^ Deployment loop resistance measurement test

If the voltage out of range test detects a short to voltage condition, the resistance measurement test for that deployment loop will not be
performed.

CONDITIONS FOR RUNNING THE DTC


Deployment loop voltage out of range test:
^ Ignition 1 voltage is within the normal operating voltage range.
^ Passenger frontal deployment loop is not shorted to voltage.
^ Passenger frontal high terminal A3 is less than 2 Volts.

Deployment loop resistance measurement test:


^ Ignition 1 voltage is within the normal operating voltage range.
^ Passenger frontal deployment loop is not shorted to voltage.
^ Passenger frontal deployment loop is not shorted to ground.

CONDITIONS FOR SETTING THE DTC


Deployment loop voltage out of range test-Passenger frontal deployment loop resistance is at least 6 Ohms for 300 milliseconds.
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 154
Chevrolet Venture V6-3.4L VIN E 1834

Deployment loop resistance measurement test -Passenger frontal deployment loop resistance is more than 3.7 Ohms for 300 milliseconds.

ACTION TAKEN WHEN THE DTC SETS


The SDM commands ON the AIR BAG warning lamp via Class 2 serial data.

CONDITIONS FOR CLEARING THE DTC


^ You can issue a CLEAR CODES command
^ A history DTC will clear once 255 malfunction free ignition cycles have occurred

DIAGNOSTIC AIDS
The following can cause an intermittent condition:
^ The inflatable restraint IP module 2-way harness connector terminal A and terminal B.
^ The SDM wiring harness connector terminal A3 and terminal A8.
^ The wire to terminal connections in the passenger frontal high circuit.
^ The wire to terminal connections in the passenger frontal low circuit.
^ Refer to Testing for Intermittent and Poor Connections in Diagrams.

TEST DESCRIPTION

Steps 1 - 6
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 155
Chevrolet Venture V6-3.4L VIN E 1835

Steps 7 - 14

The number(s) below refer to the step number(s) on the diagnostic table.
2. This step checks the inline connector C216
7. This step checks the SDM wiring harness connector.
9. This step checks for an open or a high resistance in the passenger frontal high circuit.
11. This step determines if there is an open or a high resistance in the passenger frontal low circuit or if there is a malfunctioning SDM.

B0018
DTC B0018 RF/Passenger Frontal Deployment Loop (Single Stage or Stage 1) Short to Ground/Voltage Out of Range
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 156
Chevrolet Venture V6-3.4L VIN E 1836

Schematic

CIRCUIT DESCRIPTION
When you first turn ON the ignition, the inflatable restraint Sensing and Diagnostic Module (SDM) performs tests to diagnose critical
malfunctions within itself. Then the SDM performs the following continuous diagnostic tests on the deployment loops:
^ Deployment loop voltage out of range test
^ Deployment loop resistance measurement test

If the voltage out of range test detects a short to voltage condition, the resistance measurement test for that deployment loop will not be
performed.

CONDITIONS FOR RUNNING THE DTC


Deployment loop voltage out of range test-Ignition 1 voltage is within the normal operating voltage range.
Deployment loop resistance measurement test:
^ Ignition 1 voltage is within the normal operating voltage range.
^ Passenger frontal deployment loop is not shorted to voltage.

CONDITIONS FOR SETTING THE DTC


Deployment loop voltage out of range test-Passenger frontal high terminal A3 is more than 6 volts for 300 milliseconds.

Deployment loop resistance measurement test-Passenger frontal high terminal A3 of is less than 2 volts AND passenger frontal deployment loop
resistance is less than 6 Ohms for 300 milliseconds.

ACTION TAKEN WHEN THE DTC SETS


The SDM commands ON the AIR BAG warning lamp via Class 2 serial data.

CONDITIONS FOR CLEARING THE DTC


^ You can issue a CLEAR CODES command
^ A history DTC will clear once 255 malfunction free ignition cycles have occurred

DIAGNOSTIC AIDS
A short to B+ or a short to ground condition in the inflatable restraint IP module deployment loop can cause an intermittent condition. Inspect the
passenger frontal high and passenger frontal low circuits carefully for cutting or chafing. Wiring pigtail damage requires replacement of the
inflatable restraint IP module.

TEST DESCRIPTION
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 157
Chevrolet Venture V6-3.4L VIN E 1837

Steps 1 - 7
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 158
Chevrolet Venture V6-3.4L VIN E 1838

Steps 8 - 16

The number(s) below refer to the step number(s) on the diagnostic table.
2. This step checks the inline connector C216.
7. This step checks to see if there is a short to ground in the passenger frontal high circuit.
9. This step checks to see if there is a short to ground in the passenger frontal low circuit.
11. This step checks to see if there is a short to B+ in the passenger frontal high circuit.
13. This step determines if there is a short to B+ in the passenger frontal low circuit or if there is a malfunctioning SDM.
16. This step clears all SIR and all communication DTCs.

B0022
DTC B0022 LF/Driver Front Deploy Loop (Single Stage or Stage 1) Resist Low
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 159
Chevrolet Venture V6-3.4L VIN E 1839

Schematic

CIRCUIT DESCRIPTION
When you first turn ON the ignition, the inflatable restraint Sensing and Diagnostic Module (SDM) performs tests to diagnose critical
malfunctions within itself. Then the SDM performs the following continuous diagnostic tests on the deployment loops:
^ Deployment loop voltage out of range test
^ Deployment loop resistance measurement test

If the voltage out of range test detects a short to voltage condition, the resistance measurement test for that deployment loop will not be
performed.

CONDITIONS FOR RUNNING THE DTC


^ Ignition 1 voltage is within the normal operating voltage range.
^ Driver frontal deployment loop is not open.
^ Driver frontal deployment loop is not shorted to voltage.
^ Driver frontal deployment loop is not shorted to ground.

CONDITIONS FOR SETTING THE DTC


Driver frontal deployment loop resistance is less than 1.3 Ohms for 300 milliseconds.

ACTION TAKEN WHEN THE DTC SETS


The SDM commands ON the AIR BAG warning lamp via Class 2 serial data.

CONDITIONS FOR CLEARING THE DTC


^ You can issue a CLEAR CODES command
^ A history DTC will clear once 255 malfunction free ignition cycles have occurred

DIAGNOSTIC AIDS
The following can cause an intermittent condition:
^ A short between the driver frontal high and driver frontal low circuits.
^ A malfunctioning shorting bar on the inflatable restraint steering wheel module 2-way connector
^ A malfunctioning shorting bar on the inflatable restraint steering wheel module coil 2-way connector.
^ Refer to Testing for Intermittent and Poor Connections in Diagrams.

TEST DESCRIPTION
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 160
Chevrolet Venture V6-3.4L VIN E 1840

Steps 1 - 7
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 161
Chevrolet Venture V6-3.4L VIN E 1841

Steps 8 - 12

The number(s) below refer to the step number(s) on the diagnostic table.
2. This step checks the inline connector C215.
9. This step determines if there is a short between the driver frontal high and driver frontal low circuits or if there is a malfunctioning SDM.

B0024
DTC B0024 LF/Driver Frontal Deployment Loop (Single Stage or Stage 1) Short to Ground/Voltage Out of Range

Schematic

CIRCUIT DESCRIPTION
When you first turn ON the ignition, the inflatable restraint sensing and diagnostic module (SDM) performs tests to diagnose critical
malfunctions within itself. Then the SDM performs the following continuous diagnostic tests on the deployment loops:
^ Deployment loop voltage out of range test
^ Deployment loop resistance measurement test

If the voltage out of range test detects a short to voltage condition, the resistance measurement test for that deployment loop will not be
performed.

CONDITIONS FOR RUNNING THE DTC


Deployment loop voltage out of range test - Ignition 1 voltage is within the normal operating voltage range.
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 162
Chevrolet Venture V6-3.4L VIN E 1842

Deployment loop resistance measurement test:


^ Ignition 1 voltage is within the normal operating voltage range.
^ Driver frontal deployment loop is not shorted to voltage.

CONDITIONS FOR SETTING THE DTC


Deployment loop voltage out of range test-Driver frontal high terminal A6 is more than 6 Volts for 300 milliseconds.

Deployment loop resistance measurement test-Driver frontal high terminal A6 is less than 2 Volts AND driver frontal deployment loop resistance
is less than 6 Ohms for 300 milliseconds.

ACTION TAKEN WHEN THE DTC SETS


The SDM commands ON the AIR BAG warning lamp via Class 2 serial data.

CONDITIONS FOR CLEARING THE DTC


^ You can issue a CLEAR CODES command
^ A history DTC will clear once 255 malfunction free ignition cycles have occurred

DIAGNOSTIC AIDS
A short to B+ or a short to ground in the inflatable restraint steering wheel module deployment loop can cause an intermittent condition. Inspect
the driver frontal high and driver frontal low circuits carefully for cutting or chafing. Wiring pigtail damage requires replacement of the inflatable
restraint steering wheel module coil.

TEST DESCRIPTION
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 163
Chevrolet Venture V6-3.4L VIN E 1843

Steps 1 - 7
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 164
Chevrolet Venture V6-3.4L VIN E 1844

Steps 8 - 18

The number(s) below refer to the step number(s) on the diagnostic table.
2. This step checks the inline connector C215.
6. This step determines if the inflatable restraint steering wheel module coil or the inflatable restraint steering wheel module is defective.
9. This step checks to see if there is a short to ground in the driver frontal high circuit.
11. This step checks to see if there is a short to ground in the driver frontal low circuit.
13. This step checks to see if there is a short to B+ in the driver frontal high circuit.
15. This step determines if there is a short to B+ in the driver frontal low circuit or if there is a malfunctioning SDM.

B0026
DTC B0026 LF/Driver Frontal Deployment Loop (Single Stage or Stage 1) Open
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 165
Chevrolet Venture V6-3.4L VIN E 1845

Schematic

CIRCUIT DESCRIPTION
When you first turn ON the ignition, the inflatable restraint sensing and diagnostic module (SDM) performs tests to diagnose critical
malfunctions within itself. Then the SDM performs the following continuous diagnostic tests on the deployment loops:
^ Deployment loop voltage out of range test
^ Deployment loop resistance measurement test

If the voltage out of range test detects a short to voltage condition, the resistance measurement test for that deployment loop will not be
performed.

CONDITIONS FOR RUNNING THE DTC


Deployment loop voltage out of range test:
^ Ignition 1 voltage is within the normal operating voltage range.
^ Driver frontal deployment loop is not shorted to voltage.
^ Driver frontal high terminal A6 is less than 2 Volts.

Deployment loop resistance measurement test:


^ Ignition 1 voltage is within the normal operating voltage range.
^ Driver frontal deployment loop is not shorted to voltage.
^ Driver frontal deployment loop is not shorted to ground.

CONDITIONS FOR SETTING THE DTC


Deployment loop voltage out of range test-Driver frontal deployment loop resistance is at least 6 Ohms for 300 milliseconds.

Deployment loop resistance measurement test - Driver frontal deployment loop resistance is more than 4.8 Ohms for 300 milliseconds.

ACTION TAKEN WHEN THE DTC SETS


The SDM commands ON the AIR BAG warning lamp via Class 2 serial data.

CONDITIONS FOR CLEARING THE DTC


^ You can issue a CLEAR CODES command
^ A history DTC will clear once 255 malfunction free ignition cycles have occurred

DIAGNOSTIC AIDS
The following can cause an intermittent condition:
^ The inflatable restraint steering wheel module 2-way connector.
^ The inflatable restraint steering wheel module coil 2-way harness connector terminal A and terminal B.
^ The SDM wiring harness connector terminal A6 and terminal A7.
^ The wire to terminal connections in the driver frontal high circuit.
^ The wire to terminal connections in the driver frontal low circuit.
^ Refer to Testing for intermittent and Poor Connections in Diagrams.

TEST DESCRIPTION
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 166
Chevrolet Venture V6-3.4L VIN E 1846

Steps 1 - 7
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 167
Chevrolet Venture V6-3.4L VIN E 1847

Steps 8 - 16

The number(s) below refer to the step number(s) on the diagnostic table.
2. This step checks the inline connector C215.
6. This step determines if the inflatable restraint steering wheel module coil or the inflatable restraint steering wheel module is defective.
9. This step checks to see if the SDM wiring harness connector is OK.
11. This step checks to see if there is an open or a high resistance in the driver frontal high circuit.
13. This step determines if there is an open or a high resistance in the driver frontal low circuit or if there is a malfunctioning SDM.

B0028
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 168
Chevrolet Venture V6-3.4L VIN E 1848

Schematic

CIRCUIT DESCRIPTION
When you first turn ON the ignition, the inflatable restraint Sensing and Diagnostic Module (SDM) performs tests to diagnose critical
malfunctions within itself. Then the SDM performs the following continuous diagnostic tests on the deployment loops:
^ Deployment loop voltage out of range test
^ Deployment loop resistance measurement test

If the voltage out of range test detects a short to voltage condition, the resistance measurement test for that deployment loop will not be
performed.

CONDITIONS FOR RUNNING THE DTC


^ Ignition 1 voltage is within the normal operating voltage range.
^ Passenger side deployment loop is not open.
^ Passenger side deployment loop is not shorted to voltage.
^ Passenger side deployment loop is not shorted to ground.

CONDITIONS FOR SETTING THE DTC


Passenger side deployment loop resistance is less than 1.3 Ohms for 300 milliseconds.

ACTION TAKEN WHEN THE DTC SETS


The SDM commands ON the AIR BAG warning lamp via Class 2 serial data.

CONDITIONS FOR CLEARING THE DTC


^ You can issue a CLEAR CODES command
^ A history DTC will clear once 255 malfunction free ignition cycles have occurred

DIAGNOSTIC AIDS
The following can cause an intermittent condition:
^ A short between the passenger side high and the passenger side low circuits.
^ A malfunctioning shorting bar on the inflatable restraint passenger seat module yellow 2-way connector.
^ Refer to Testing for Intermittent and Poor Connections in Diagrams.

TEST DESCRIPTION
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 169
Chevrolet Venture V6-3.4L VIN E 1849

Steps 1 - 6
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 170
Chevrolet Venture V6-3.4L VIN E 1850

Steps 7 - 10

The number(s) below refer to the step number(s) on the diagnostic table.
2. This step checks the inflatable restraint passenger seat module yellow 2-way connector.
5. This step checks to see if there is a malfunctioning inflatable restraint passenger seat module.
7. This step determines if there is a short between the passenger side high and the passenger side low or it there is a malfunctioning SDM.

B0029

Schematic

CIRCUIT DESCRIPTION
When you first turn ON the ignition, the inflatable restraint Sensing and Diagnostic Module (SDM) performs tests to diagnose critical
malfunctions within itself. Then the SDM performs the following continuous diagnostic tests on the deployment loops:
^ Deployment loop voltage out of range test
^ Deployment loop resistance measurement test

If the voltage out of range test detects a short to voltage condition, the resistance measurement test for that deployment loop will not be
performed.

CONDITIONS FOR RUNNING THE DTC


Deployment loop voltage out of range test:
^ Ignition 1 voltage is within the normal operating voltage range.
^ Passenger side deployment loop is not shorted to voltage.
^ Passenger side high terminal B4 is less than 2 Volts.

Deployment loop resistance measurement test:


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 171
Chevrolet Venture V6-3.4L VIN E 1851
^ Ignition 1 voltage is within the normal operating voltage range.
^ Passenger side deployment loop is not shorted to voltage.
^ Passenger side deployment loop is not shorted to ground.

CONDITIONS FOR SETTING THE DTC


Deployment loop voltage out of range test-Passenger side deployment loop resistance is at least 6 Ohms for 300 milliseconds.

Deployment loop resistance measurement test - Passenger side deployment loop resistance is more than 3.7 Ohms for 300 milliseconds.

ACTION TAKEN WHEN THE DTC SETS


The SDM commands ON the AIR BAG warning lamp via Class 2 serial data.

CONDITIONS FOR CLEARING THE DTC


^ You can issue a CLEAR CODES command
^ A history DTC will clear once 255 malfunction free ignition cycles have occurred

DIAGNOSTIC AIDS
The following can cause an intermittent condition:
^ The inflatable restraint passenger seat module yellow 2-way harness connector terminal A and terminal B.
^ The SDM wiring harness connector terminal B3 and terminal B4.
^ The wire to terminal connections in the passenger side high circuit.
^ The wire to terminal connections in the passenger side low circuit.
^ Refer to Testing for Intermittent and Poor Connections in Diagrams.

TEST DESCRIPTION
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 172
Chevrolet Venture V6-3.4L VIN E 1852

Steps 1 - 6
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 173
Chevrolet Venture V6-3.4L VIN E 1853

Steps 7 - 12

The number(s) below refer to the step number(s) on the diagnostic table.
2. This step checks the inflatable restraint passenger seat module yellow 2-way connector.
5. This step checks to see if there is a malfunctioning inflatable restraint passenger seat module.
7. This step checks to see if there is an open or a high resistance in the passenger side high circuit.
9. This step determines if there is an open or a high resistance in the passenger side low circuit or if there is a malfunctioning SDM.

B0030
DTC B0030 RF/Passenger Side Deployment Loop Short to Ground/Voltage Out of Range

Schematic

CIRCUIT DESCRIPTION
When you first turn ON the ignition, the inflatable restraint Sensing and Diagnostic Module (SDM) performs tests to diagnose critical
malfunctions within itself. Then the SDM performs the following continuous diagnostic tests on the deployment loops:
^ Deployment loop voltage out of range test
^ Deployment loop resistance measurement test

If the voltage out of range test detects a short to voltage condition, the resistance measurement test for that deployment loop will not be
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 174
Chevrolet Venture V6-3.4L VIN E 1854
performed.

CONDITIONS FOR RUNNING THE DTC


Deployment loop voltage out of range -Ignition 1 voltage is within the normal operating voltage range.

Deployment loop resistance measurement test:


^ Ignition 1 voltage is within the normal operating voltage range.
^ Passenger side deployment loop is not shorted to voltage.

CONDITIONS FOR SETTING THE DTC


Deployment loop voltage out of range test - Passenger side high terminal B4 is more than 6 Volts for 300 milliseconds.

Deployment loop resistance measurement test - Passenger side high terminal B4 is less than 2 Volts AND passenger side deployment loop
resistance is less than 6 Ohms for 300 milliseconds.

ACTION TAKEN WHEN THE DTC SETS


The SDM commands ON the AIR BAG warning lamp via Class 2 serial data.

CONDITIONS FOR CLEARING THE DTC


^ You can issue a CLEAR CODES command
^ A history DTC will clear once 255 malfunction tree ignition cycles have occurred

DIAGNOSTIC AIDS
A short to B+ or a short to ground in the inflatable restraint passenger seat module deployment loop can cause an intermittent condition. Inspect
the passenger side high and passenger side low circuits carefully for cutting or chafing. Wiring pigtail damage requires replacement of the
inflatable restraint passenger seat module.

TEST DESCRIPTION
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 175
Chevrolet Venture V6-3.4L VIN E 1855

Steps 1 - 6
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 176
Chevrolet Venture V6-3.4L VIN E 1856

Steps 7 - 16

The number(s) below refer to the step number(s) on the diagnostic table.
2. This step checks the inflatable restraint passenger seat module yellow 2-way connector.
5. This step checks to see if there is a malfunctioning inflatable restraint passenger seat module.
7. This step checks to see if there is a short to ground in the passenger side high circuit.
9. This step checks to see if there is a short to ground in the passenger side low circuit.
11. This step checks to see if there is a short to B+ in the passenger side high circuit.
13. This step determines if there is a short to B+ in the passenger side low circuit or if there is a malfunctioning SDM.
16. This step clears all SIR and all communication DTCs.
B0040
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 177
Chevrolet Venture V6-3.4L VIN E 1857

Schematic

CIRCUIT DESCRIPTION
When you first turn ON the ignition, the inflatable restraint Sensing and Diagnostic Module (SDM) performs tests to diagnose critical
malfunctions within itself. Then the SDM performs the following continuous diagnostic tests on the deployment loops:
^ Deployment loop voltage out of range test
^ Deployment loop resistance measurement test

If the voltage out of range test detects a short to voltage condition, the resistance measurement test for that deployment loop will not be
performed.

CONDITIONS FOR RUNNING THE DTC


^ Ignition 1 voltage is within the normal operating voltage range.
^ Driver side deployment loop is not open
^ Driver side deployment loop is not shorted to voltage.
^ Driver side deployment loop is not shorted to ground.

CONDITIONS FOR SETTING THE DTC


Driver side deployment loop resistance is less than 1.3 Ohms for 300 milliseconds.

ACTION TAKEN WHEN THE DTC SETS


The SDM commands ON the AIR BAG warning lamp via Class 2 serial data.

CONDITIONS FOR CLEARING THE DTC


^ You can issue a CLEAR CODES command
^ A history DTC will clear once 255 malfunction tree ignition cycles have occurred

DIAGNOSTIC AIDS
The following can cause an intermittent condition:
^ A short between the driver side high and the driver side low circuits.
^ A malfunctioning shorting bar on the inflatable restraint driver seat module yellow 2-way connector.
^ Refer to Testing for Intermittent and Poor Connections in Diagrams.

TEST DESCRIPTION
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 178
Chevrolet Venture V6-3.4L VIN E 1858

Steps 1 - 6
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 179
Chevrolet Venture V6-3.4L VIN E 1859

Steps 7 - 10

The number(s) below refer to the step number(s) on the diagnostic table.
2. This step checks the inflatable restraint driver seat module yellow 2-way connector.
5. This step checks to see if there is a malfunctioning inflatable restraint driver seat module.
7. This step determines if there is a short between the driver side high and the driver side low or if there is a malfunctioning SDM.

B0041

Schematic

CIRCUIT DESCRIPTION
When you first turn ON the ignition, the inflatable restraint Sensing and Diagnostic Module (SDM) performs tests to diagnose critical
malfunctions within itself. Then the SDM performs the following continuous diagnostic tests on the deployment loops:
^ Deployment loop voltage out of range test
^ Deployment loop resistance measurement test

If the voltage out of range test detects a short to voltage condition, the resistance measurement test for that deployment loop will not be
performed.

CONDITIONS FOR RUNNING THE DTC


Deployment loop voltage out of range test:
^ Ignition 1 voltage is within the normal operating voltage range.
^ Driver side deployment loop is not shorted to voltage.
^ Driver side high terminal B1 is less than 2 Volts.

Deployment loop resistance measurement test:


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 180
Chevrolet Venture V6-3.4L VIN E 1860
^ Ignition 1 voltage is within the normal operating voltage range.
^ Driver side deployment loop is not shorted to voltage.
^ Driver side deployment loop is not shorted to ground.

CONDITIONS FOR SETTING THE DTC


Deployment loop voltage out of range test - Driver side deployment loop resistance is at least 6 Ohms for 300 milliseconds.
Deployment loop resistance measurement test - Driver side deployment loop resistance is more than 3.7 Ohms for 300 milliseconds.

ACTION TAKEN WHEN THE DTC SETS


The SDM commands ON the AIR BAG warning lamp via Class 2 serial data.

CONDITIONS FOR CLEARING THE DTC


^ You can issue a CLEAR CODES command
^ A history DTC will clear once 255 malfunction free ignition cycles have occurred

DIAGNOSTIC AIDS
The following can cause an intermittent condition:
^ The inflatable restraint driver seat module yellow 2-way harness connector terminal A and terminal B.
^ The SDM wiring harness connector terminal B1 and terminal B2.
^ The wire to terminal connections in the driver side high circuit.
^ The wire to terminal connections in the driver side low circuit.
^ Refer to Testing for Intermittent and Poor Connections in Diagrams.

TEST DESCRIPTION
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 181
Chevrolet Venture V6-3.4L VIN E 1861

Steps 1 - 6
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 182
Chevrolet Venture V6-3.4L VIN E 1862

Steps 7 - 12

The number(s) below refer to the step number(s) on the diagnostic table.
2. This step checks the inflatable restraint driver seat module yellow 2-way connector.
5. This step checks to see if there is a malfunctioning inflatable restraint driver seat module.
7. This step checks to see if there is an open or a high resistance in the driver side high circuit.
9. This step determines if there is an open or a high resistance in the driver side low circuit or if there is a malfunctioning SDM.

B0045

Schematic

CIRCUIT DESCRIPTION
When you first turn ON the ignition, the inflatable restraint Sensing and Diagnostic Module (SDM) performs tests to diagnose critical
malfunctions within itself. Then the SDM performs the following continuous diagnostic tests on the deployment loops:
^ Deployment loop voltage out of range test
^ Deployment loop resistance measurement test

If the voltage out of range test detects a short to voltage condition, the resistance measurement test for that deployment loop will not be performed.
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 183
Chevrolet Venture V6-3.4L VIN E 1863

CONDITIONS FOR RUNNING THE DTC


Deployment loop voltage out of range Ignition1 voltage is within the normal operating voltage range.

Deployment loop resistance measurement test:


^ Ignition 1 voltage is within the normal operating voltage range.
^ Driver side deployment loop is not shorted to voltage.

CONDITIONS FOR SETTING THE DTC


Deployment loop voltage out of range test Driver side high terminal B1 is more than 6 Volts for 300 milliseconds.

Deployment loop resistance measurement test - Driver side high terminal B1 is less than 2 Volts AND driver side deployment loop resistance is
less than 6 Ohms for 300 milliseconds.

ACTION TAKEN WHEN THE DTC SETS


The SDM commands ON the AIR BAG warning lamp via Class 2 serial data.

CONDITIONS FOR CLEARING THE DTC


^ You can issue a CLEAR CODES command
^ A history DTC will clear once 255 malfunction free ignition cycles have occurred

DIAGNOSTIC AIDS
A short to B+ or a short to ground in the inflatable restraint driver seat module deployment loop can cause an intermittent condition. Inspect the
driver side high and driver side low circuits carefully for cutting or chafing. Wiring pigtail damage requires replacement of the inflatable restraint
driver seat module.

TEST DESCRIPTION
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 184
Chevrolet Venture V6-3.4L VIN E 1864

Steps 1 - 6
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 185
Chevrolet Venture V6-3.4L VIN E 1865

Steps 7 - 16

The number(s) below refer to the step number(s) on the diagnostic table.
2. This step checks the inflatable restraint driver seat module yellow 2-way connector.
5. This step checks to see if there is a malfunctioning inflatable restraint driver seat module.
7. This step checks to see if there is a short to ground in the driver side high circuit.
9. This step checks to see if there is a short to ground in the driver side low circuit.
11. This step checks to see if there is a short to B+ in the driver side high circuit.
13. This step determines if there is a short to B+ in the driver side low circuit or if there is a malfunctioning SDM.
16. This step clears all SIR and all communication DTCs.

B0051
CIRCUIT DESCRIPTION
The inflatable restraint Sensing and Diagnostic Module (SDM) contains sensing devices that converts vehicle velocity changes to an electrical
signal. The SDM processes the generated electrical signals and compares it to a value stored in memory. When the generated signals exceeds the
stored value, the SDM performs additional signal processing and compares the generated signals to signals stored in memory. When two of the
generated signals exceed the stored values, the SDM will cause current to flow through the inflator modules, deploying the air bags and the seat
belt pretensioners, causing DTC B0051 to set.
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 186
Chevrolet Venture V6-3.4L VIN E 1866

CONDITIONS FOR RUNNING THE DTC


Ignition voltage must be present to the SDM.

CONDITIONS FOR SETTING THE DTC


^ The SDM detects a frontal crash, up to 30 degrees off the centerline of the vehicle, of sufficient force to warrant deployment of the frontal air
bags.
^ The SDM detects a side impact crash of sufficient force to warrant deployment of a side air bag.

ACTION TAKEN WHEN THE DTC SETS


^ The SDM commands ON the AIR BAG warning lamp via Class 2 serial data.
^ The SDM records crash data.

CONDITIONS FOR CLEARING THE DTC


DTC B0051 is a latched code. You cannot clear a latched code. Replace the SDM after following the instructions in the diagnostic table.

TEST DESCRIPTION

Diagnostic Chart

The numbers below refer to the step numbers on the diagnostic table:
2. If the inflator module(s) has not deployed, DTC B0051 may have set falsely.
3. If DTC B0051 has set with no signs of frontal impact, the DTC may have falsely.

B0053
CIRCUIT DESCRIPTION
The inflatable restraint Sensing and Diagnostic Module (SDM) contains sensing devices that convert vehicle velocity changes to an electrical
signal. The SDM processes the generated electrical signal and compares it to a value stored in memory. When the generated signal exceeds the
stored value, the SDM performs additional signal processing and compares the generated signals to signals stored in memory. When two of the
generated signals exceed the stored values, the SDM will cause current to flow through the inflator modules, deploying the air bags and the seat
belt pretensioners. DTC B0053 will set along with a DTC B0051 when a deployment occurs while an inflator circuit fault is present that could
possibly result in a non-deployment situation in one or more inflator modules or seat belt pretensioners.

CONDITIONS FOR RUNNING THE DTC


Ignition voltage must be present to the SDM.

CONDITIONS FOR SETTING THE DTC


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 187
Chevrolet Venture V6-3.4L VIN E 1867
^ The SDM detects a frontal crash, up to 30 degrees off the centerline of the vehicle, of sufficient force to warrant deployment of the frontal air
bags.
^ The SDM detects a side impact crash of sufficient force to warrant deployment of a side air bag.

ACTION TAKEN WHEN THE DTC SETS


^ The SDM commands ON the AIR BAG warning lamp via Class 2 serial data.
^ The SDM records crash data.

CONDITIONS FOR CLEARING THE DTC


DTC B0053 is a latched code. You cannot clear a latched code. Replace the SDM after following the instructions in the diagnostic table.

DIAGNOSTIC AIDS
DTC B0053 will be accompanied by another DTC (other than DTC B1000). Repair the malfunction causing the other DTCs before installing a
new SDM.

TEST DESCRIPTION

Diagnostic Chart

The numbers below refer to the step numbers on the diagnostic table:
2. If the inflator module(s) has not deployed, DTC B0053 may have set falsely.
3. If DTC B0053 has set with no signs of frontal impact, the DTC may have set falsely.

B0057
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 188
Chevrolet Venture V6-3.4L VIN E 1868

Schematic

CIRCUIT DESCRIPTION
When you first turn ON the ignition, the inflatable restraint Sensing and Diagnostic Module (SDM) performs tests to diagnose critical
malfunctions within itself. Then the SDM performs the following continuous diagnostic tests on the deployment loops:
^ Deployment loop voltage out of range test
^ Deployment loop resistance measurement test

If the voltage out of range test detects a short to voltage condition, the resistance measurement test for that deployment loop will not be
performed.

CONDITIONS FOR RUNNING THE DTC


^ Ignition 1 voltage is within the normal operating voltage range.
^ Passenger seat belt pretensioner deployment loop is not open.
^ Passenger seat belt pretensioner deployment loop is not shorted to voltage.
^ Passenger seat belt pretensioner deployment loop is not shorted to ground.

CONDITIONS FOR SETTING THE DTC


Passenger seat belt pretensioner deployment loop resistance is less than 1.3 Ohms for 300 milliseconds.

ACTION TAKEN WHEN THE DTC SETS


The SDM commands ON the AIR BAG warning lamp via Class 2 serial data.

CONDITIONS FOR CLEARING THE DTC


^ You can issue a CLEAR CODES command
^ A history DTC will clear once 255 malfunction free ignition cycles have occurred

DIAGNOSTIC AIDS
The following can cause an intermittent condition:
^ A short between the passenger belt high and the passenger belt low circuits.
^ A malfunctioning shorting bar on the passenger seat belt pretensioner yellow 2-way connector.
^ Refer to Testing for Intermittent and Poor Connections in Diagrams.

TEST DESCRIPTION
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 189
Chevrolet Venture V6-3.4L VIN E 1869

Steps 1 - 6
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 190
Chevrolet Venture V6-3.4L VIN E 1870

Steps 7 - 10

The number(s) below refer to the step number(s) on the diagnostic table.
2. This step checks the passenger seat belt pretensioner yellow 2-way connector.
5. This step checks to see if there is a malfunctioning passenger seat belt pretensioner.
7. This step determines if there is a short between the passenger belt high and the passenger belt low or if there is a malfunctioning SDM.

B0058

Schematic

CIRCUIT DESCRIPTION
When you first turn ON the ignition, the inflatable restraint Sensing and Diagnostic Module (SDM) performs tests to diagnose critical
malfunctions within itself. Then the SDM performs the following continuous diagnostic tests on the deployment loops:
^ Deployment loop voltage out of range test
^ Deployment loop resistance measurement test

If the voltage out of range test detects a short to voltage condition, the resistance measurement test for that deployment loop will not be
performed.

CONDITIONS FOR RUNNING THE DTC


Deployment loop voltage out of range test:
^ Ignition 1 voltage is within the normal operating voltage range.
^ Passenger seat belt pretensioner deployment loop is not shorted to voltage.
^ Passenger belt high terminal C4 is less than 2 Volts.

Deployment loop resistance measurement test:


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 191
Chevrolet Venture V6-3.4L VIN E 1871
^ Ignition 1 voltage is within the normal operating voltage range.
^ Passenger seat belt pretensioner deployment loop is not shorted to voltage.
^ Passenger seat belt pretensioner deployment loop is not shorted to ground.

CONDITIONS FOR SETTING THE DTC


Deployment loop voltage out of range test - Passenger seat belt pretensioner deployment loop resistance is at least 6 Ohms for 300 milliseconds.
Deployment loop resistance measurement test - Passenger seat belt pretensioner deployment loop resistance is more than 3.7 Ohms for 300
milliseconds.

ACTION TAKEN WHEN THE DTC SETS


The SDM commands ON the AIR BAG warning lamp via Class 2 serial data.

CONDITIONS FOR CLEARING THE DTC


^ You can issue a CLEAR CODES command
^ A history DTC will clear once 255 malfunction free ignition cycles have occurred

DIAGNOSTIC AIDS
The following can cause an intermittent condition:
^ The passenger seat belt pretensioner yellow 2-way harness connector terminal A and terminal B.
^ The SDM wiring harness connector terminal C3 and terminal C4
^ The wire to terminal connections in the passenger belt high circuit.
^ The wire to terminal connections in the passenger belt low circuit.
^ Refer to Testing for Intermittent and Poor Connections in Diagrams.

TEST DESCRIPTION
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 192
Chevrolet Venture V6-3.4L VIN E 1872

Steps 1 - 7
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 193
Chevrolet Venture V6-3.4L VIN E 1873

Steps 8 - 12

The number(s) below refer to the step number(s) on the diagnostic table.
2. This step checks the passenger seat belt pretensioner yellow 2-way connector.
5. This step checks to see if there is a malfunctioning passenger seat belt pretensioner.
7. This step checks to see if there is an open or a high resistance in the passenger belt high circuit.
9. This step determines if there is an open or a high resistance in the passenger belt low circuit or if there is a malfunctioning SDM.

B0059
DTC B0059 RF/Passenger Pretensioner Deployment Loop Short to Ground/Voltage Out of Range

Schematic

CIRCUIT DESCRIPTION
When you first turn ON the ignition, the inflatable restraint Sensing and Diagnostic Module (SDM) performs tests to diagnose critical
malfunctions within itself. Then the SDM performs the following continuous diagnostic tests on the deployment loops:
^ Deployment loop voltage out of range test
^ Deployment loop resistance measurement test

If the voltage out of range test detects a short to voltage condition, the resistance measurement test for that deployment loop will not be
performed.

CONDITIONS FOR RUNNING THE DTC


Deployment loop voltage out of range - Ignition 1 voltage is within the normal operating voltage range.

Deployment loop resistance measurement test:


^ Ignition 1 voltage is within the normal operating voltage range.
^ Passenger seat belt pretensioner deployment loop is not shorted to voltage.
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 194
Chevrolet Venture V6-3.4L VIN E 1874

CONDITIONS FOR SETTING THE DTC


Deployment loop voltage out of range test - Passenger belt high terminal C4 is more than 6 Volts for 300 milliseconds.
Deployment loop resistance measurement test - Passenger belt high terminal C4 is less than 2 Volts AND passenger seat belt pretensioner
deployment loop resistance is less than 6 Ohms for 300 milliseconds.

ACTION TAKEN WHEN THE DTC SETS


The SDM commands ON the AIR BAG warning lamp via Class 2 serial data.

CONDITIONS FOR CLEARING THE DTC


^ You can issue a CLEAR CODES command
^ A history DTC will clear once 255 malfunction free ignition cycles have occurred

DIAGNOSTIC AIDS
A short to B+ or a short to ground in the passenger seat belt pretensioner deployment loop can cause an intermittent condition. Inspect the
passenger belt high and passenger belt low circuits carefully for cutting and chafing. Wiring pigtail damage requires replacement of the
passenger seat belt pretensioner.

TEST DESCRIPTION

Steps 1 - 6
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 195
Chevrolet Venture V6-3.4L VIN E 1875

Steps 7 - 16

The number(s) below refer to the step number(s) on the diagnostic table.
2. This step checks the passenger seat belt pretensioner yellow 2-way connector.
5. This step checks to see if there is a malfunctioning passenger seat belt pretensioner.
7. This step checks to see if there is a short to ground in the passenger belt high circuit.
9. This step checks to see if there is a short to ground in the passenger belt low circuit.
11. This step checks to see if there is a short to B+ in the passenger belt high circuit.
13. This step determines if there is a short to B+ in the passenger belt low circuit or if there is a malfunctioning SDM.
16. This step clears all SIR and all communication DTCs.

B0064
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 196
Chevrolet Venture V6-3.4L VIN E 1876

Schematic

CIRCUIT DESCRIPTION
When you first turn ON the ignition, the inflatable restraint Sensing and Diagnostic Module (SDM) performs tests to diagnose critical
malfunctions within itself. Then the SDM performs the following continuous diagnostic tests on the deployment loops:
^ Deployment loop voltage out of range test
^ Deployment loop resistance measurement test

If the voltage out of range test detects a short to voltage condition, the resistance measurement test for that deployment loop will not be
performed.

CONDITIONS FOR RUNNING THE DTC


^ Ignition 1 voltage is within the normal operating voltage range.
^ Driver seat belt pretensioner deployment loop is not open.
^ Driver seat belt pretensioner deployment loop is not shorted to voltage.
^ Driver seat belt pretensioner deployment loop is not shorted to ground.

CONDITIONS FOR SETTING THE DTC


Driver seat belt pretensioner deployment loop resistance is less than 1.3 Ohms for 300 milliseconds.

ACTION TAKEN WHEN THE DTC SETS


The SDM commands ON the AIR BAG warning lamp via Class 2 serial data.

CONDITIONS FOR CLEARING THE DTC


^ You can issue a CLEAR CODES command
^ A history DTC will clear once 255 malfunction free ignition cycles have occurred

DIAGNOSTIC AIDS
The following can cause an intermittent condition:
^ A short between the driver belt high and the driver belt low circuits.
^ A malfunctioning shorting bar on the driver seat belt pretensioner yellow 2-way connector.
^ Refer to Testing for Intermittent and Poor Connections in Diagrams.

TEST DESCRIPTION
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 197
Chevrolet Venture V6-3.4L VIN E 1877

Steps 1 - 7
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 198
Chevrolet Venture V6-3.4L VIN E 1878

Steps 8 - 10

The number(s) below refer to the step number(s) on the diagnostic table.
2. This step checks the driver seat belt pretensioner yellow 2-way connector.
5. This step checks to see if there is a malfunctioning driver seat belt pretensioner.
7. This step determines if there is a short between the driver belt high and the driver belt low or if there is a malfunctioning SDM.

B0065

Schematic

CIRCUIT DESCRIPTION
When you first turn ON the ignition, the inflatable restraint Sensing and Diagnostic Module (SDM) performs tests to diagnose critical
malfunctions within itself. Then the SDM performs the following continuous diagnostic tests on the deployment loops:
^ Deployment loop voltage out of range test
^ Deployment loop resistance measurement test

If the voltage out of range test detects a short to voltage condition, the resistance measurement test for that deployment loop will not be
performed.

CONDITIONS FOR RUNNING THE DTC


Deployment loop voltage out of range test:
^ Ignition 1 voltage is within the normal operating voltage range.
^ Driver seat belt pretensioner deployment loop is not shorted to voltage.
^ Driver belt high terminal C1 is less than 2 Volts.

Deployment loop resistance measurement test:


^ Ignition 1 voltage is within the normal operating voltage range.
^ Driver seat belt pretensioner deployment loop is not shorted to voltage.
^ Driver seat belt pretensioner deployment loop is not shorted to ground.

CONDITIONS FOR SETTING THE DTC


Deployment loop voltage out of range test - Driver seat belt pretensioner deployment loop resistance is at least 6 Ohms for 300 milliseconds.

Deployment loop resistance measurement test - Driver seat belt pretensioner deployment loop resistance is more than 3.7 Ohms for 300
milliseconds.
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 199
Chevrolet Venture V6-3.4L VIN E 1879

ACTION TAKEN WHEN THE DTC SETS


The SDM commands ON the AIR BAG warning lamp via Class 2 serial data.

CONDITIONS FOR CLEARING THE DTC


^ You can issue a CLEAR CODES command
^ A history DTC will clear once 255 malfunction free ignition cycles have occurred

DIAGNOSTIC AIDS
The following can cause an intermittent condition:
^ The driver seat belt pretensioner yellow 2-way harness connector terminal A and terminal B.
^ The SDM wiring harness connector terminal C1 and terminal C2.
^ The wire to terminal connections in the driver belt high circuit.
^ The wire to terminal connections in the driver belt low circuit.
^ Refer to Testing for Intermittent and Poor Connections in Diagrams.

TEST DESCRIPTION
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 200
Chevrolet Venture V6-3.4L VIN E 1880

Steps 1 - 7
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 201
Chevrolet Venture V6-3.4L VIN E 1881

Steps 8 - 12

The number(s) below refer to the step number(s) on the diagnostic table.
2. This step checks the driver seat belt pretensioner yellow 2-way connector.
5. This step checks to see if there is a malfunctioning driver seat belt pretensioner.
7. This step checks to see if there is an open or a high resistance in the driver belt high circuit.
9. This step determines if there is an open or a high resistance in the driver belt low circuit or if there is a malfunctioning SDM.

B0066
DTC B0066 LF/Driver Preten Deploy Loop Short to Ground/Volt Out of Range

Schematic

CIRCUIT DESCRIPTION
When you first turn ON the ignition, the inflatable restraint Sensing and Diagnostic Module (SDM) performs tests to diagnose critical
malfunctions within itself. Then the SDM performs the following continuous diagnostic tests on the deployment loops:
^ Deployment loop voltage out of range test
^ Deployment loop resistance measurement test

If the voltage out of range test detects a short to voltage condition, the resistance measurement test for that deployment loop will not be
performed.

CONDITIONS FOR RUNNING THE DTC


Deployment loop voltage out of range - Ignition 1 voltage is within the normal operating voltage range.

Deployment loop resistance measurement test:


^ Ignition 1 voltage is within the normal operating voltage range.
^ Driver seat belt pretensioner deployment loop is not shorted to voltage.
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 202
Chevrolet Venture V6-3.4L VIN E 1882

CONDITIONS FOR SETTING THE DTC


Deployment loop voltage out of range test - Driver belt high terminal C1 is more than 6 Volts for 300 milliseconds.

Deployment loop resistance measurement test - Driver belt high terminal C1 is less than 2 Volts AND driver seat belt pretensioner deployment
loop resistance is less than 6 Ohms for 300 milliseconds.

ACTION TAKEN WHEN THE DTC SETS

The SDM commands ON the AIR BAG warning lamp via Class 2 serial data.

CONDITIONS FOR CLEARING THE DTC


^ You can issue a CLEAR CODES command
A history DTC will clear once 255 malfunction free ignition^ cycles have occurred

DIAGNOSTIC AIDS
A short to B+ or a short to ground in the driver seat belt pretensioner deployment loop can cause an intermittent condition. Inspect the driver belt
high and driver belt low circuits carefully for cutting and chafing. Wiring pigtail damage requires replacement of the driver seat belt pretensioner.

TEST DESCRIPTION
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 203
Chevrolet Venture V6-3.4L VIN E 1883

Steps 1 - 7
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 204
Chevrolet Venture V6-3.4L VIN E 1884

Steps 8 - 16

The number(s) below refer to the step number(s) on the diagnostic table.
2. This step checks the driver seat belt pretensioner yellow 2-way connector.
5. This step checks to see if there is a malfunctioning driver seat belt pretensioner.
7. This step checks to see if there is a short to ground in the driver belt high circuit.
9. This step checks to see if there is a short to ground in the driver belt low circuit.
11. This step checks to see if there is a short to B+ in the driver belt high circuit.
13. This step determines if there is a short to B+ in the driver belt low circuit or if there is a malfunctioning SDM.
16. This step clears all SIR and all communication DTCs.

B0077
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 205
Chevrolet Venture V6-3.4L VIN E 1885

Schematic

CIRCUIT DESCRIPTION
When you first turn ON the ignition, the inflatable restraint Sensing and Diagnostic Module (SDM) performs tests to diagnose critical
malfunctions within itself. The SDM provides input power to the inflatable restraint Side Impact Sensor (SIS). When input power is first
detected, the SIS responds by performing internal diagnostics. Next the SIS sends an ID message to the SDM. The SDM will consider this to be a
valid ID if the response time is less than 5 seconds after the SIS is powered up.The SIS will continually communicate a status message to the
SDM. The SDM can reset the SIS by removing and applying power to it.

CONDITIONS FOR RUNNING THE DTC


^ Ignition 1 voltage is within the normal operating voltage range.
^ The SDM monitors the inflatable restraint side impact sensor loop with the ignition ON.

CONDITIONS FOR SETTING THE DTC


The SDM has detected one of the following conditions due to a fault in the SIS interface circuit:
^ A valid ID message is not received within 5 seconds of the SIS being powered up.
^ Status message is not received
^ The SDM has failed twice to reset the SIS.

ACTION TAKEN WHEN THE DTC SETS


^ The SDM commands ON the AIR BAG warning lamp via Class 2 serial data.
^ The SDM attempts to reset the SIS.

CONDITIONS FOR CLEARING THE DTC


^ Current DTC
- The SDM has detected correct operation.
- The SIS sends an OK message to the SDM.
^ History DTC
- You issue a scan tool CLEAR CODES command.
- Once 255 malfunctions free ignition cycles have occurred.

DIAGNOSTIC AIDS
An inflatable restraint side impact sensor (SIS) circuit open, high resistance, low resistance, short to ground, or short to voltage can cause an
intermittent condition. Inspect the inflatable restraint side impact sensor high and sensor low circuits carefully for cutting and/or chafing.

TEST DESCRIPTION
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 206
Chevrolet Venture V6-3.4L VIN E 1886

Steps 1 - 8
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 207
Chevrolet Venture V6-3.4L VIN E 1887

Steps 9 - 21
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 208
Chevrolet Venture V6-3.4L VIN E 1888

Steps 22 - 28

The numbers below refer to the step numbers on the diagnostic table:
2. This step checks the inflatable restraint side impact sensor wiring harness connector.
4. This step checks the inflatable restraint side impact sensor.
7. This step checks the SDM wiring harness connector.
12. This step checks to see if there is an open or a high resistance in the inflatable restraint side impact sensor circuit.
14. This step checks to see if there is an open or a high resistance in inflatable restraint side impact sensor return circuit.
16. This step checks to see if there is a short between the inflatable restraint side impact sensor circuit and the sensor return circuit.
18. This step checks to see if there is a short to ground in the inflatable restraint side impact sensor circuit.
20. This step checks to see if there is a short to ground in the inflatable restraint side impact sensor return circuit.
22. This step checks to see if there is a short to voltage in the inflatable restraint side impact sensor circuit.
24. This step checks to see if there is a short to voltage in the inflatable restraint side impact sensor return circuit.
27. This step determines if the problem was solved by replacing the inflatable restraint side impact sensor (SIS) or it there is a malfunctioning
SDM.

B0078
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 209
Chevrolet Venture V6-3.4L VIN E 1889

Schematic

CIRCUIT DESCRIPTION
When you first turn ON the ignition, the inflatable restraint Sensing and Diagnostic Module (SDM) performs tests to diagnose critical
malfunctions within itself. The SDM provides input power to the inflatable restraint Side Impact Sensor (SIS). When input power is first
detected, the SIS responds by performing internal diagnostics. Next the SIS sends an ID message to the SDM. The SDM will consider this to be a
valid ID if the response time is less than 5 seconds after the SIS is powered up.The SIS will continually communicate a status message to the
SDM. The SDM can reset the SIS by removing and applying power to it.

CONDITIONS FOR RUNNING THE DTC


^ Ignition 1 voltage is within the normal operating voltage range.
^ The SDM monitors the inflatable restraint side impact sensor loop with the ignition ON.

CONDITIONS FOR SETTING THE DTC


The SDM has detected one of the following conditions due to a fault in the SIS interface circuit:
^ A valid ID message is not received within 5 seconds of the SIS being powered up.
^ Status message is not received
^ The SDM has failed twice to reset the SIS.

ACTION TAKEN WHEN THE DTC SETS


^ The SDM commands ON the AIR BAG warning lamp via Class 2 serial data.
^ The SDM attempts to reset the SIS.

CONDITIONS FOR CLEARING THE DTC


^ Current DTC
- The SDM has detected correct operation.
- The SIS sends an OK message to the SDM.
^ History DTC
- You issue a scan tool CLEAR CODES command.
- Once 255 malfunctions free ignition cycles have occurred.

DIAGNOSTIC AIDS
An inflatable restraint side impact sensor (SIS) circuit open, high resistance, low resistance, short to ground, or short to voltage can cause an
intermittent condition. Inspect the inflatable restraint side impact sensor high and sensor low circuits carefully for cutting and/or chafing.

TEST DESCRIPTION
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 210
Chevrolet Venture V6-3.4L VIN E 1890

Steps 1 - 9
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 211
Chevrolet Venture V6-3.4L VIN E 1891

Steps 10 - 22
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 212
Chevrolet Venture V6-3.4L VIN E 1892

Steps 23 - 28

The numbers below refer to the step numbers on the diagnostic table:
2. This step checks the inflatable restraint side impact sensor wiring harness connector.
4. This step checks the inflatable restraint side impact sensor.
7. This step checks the SDM wiring harness connector.
12. This step checks to see if there is an open or a high resistance in the inflatable restraint side impact sensor circuit.
14. This step checks to see if there is an open or a high resistance in inflatable restraint side impact sensor return circuit.
16. This step checks to see if there is a short between the inflatable restraint side impact sensor circuit and the sensor return circuit.
18. This step checks to see if there is a short to ground in the inflatable restraint side impact sensor circuit.
20. This step checks to see if there is a short to ground in the inflatable restraint side impact sensor return circuit.
22. This step checks to see if there is a short to voltage in the inflatable restraint side impact sensor circuit.
24. This step checks to see if there is a short to voltage in the inflatable restraint side impact sensor return circuit.
27. This step determines if the problem was solved by replacing the inflatable restraint side impact sensor (SIS) or if there is a malfunctioning
SDM.

B0079

Schematic
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 213
Chevrolet Venture V6-3.4L VIN E 1893

CIRCUIT DESCRIPTION
When you first turn ON the ignition, the inflatable restraint Sensing and Diagnostic Module (SDM) performs tests to diagnose critical
malfunctions within itself. The SDM provides input power to the inflatable restraint Side Impact Sensor (SIS). When input power is first
detected, the SIS responds by performing internal diagnostics. Next the SIS sends an ID message to the SDM. The SDM will consider this to be a
valid ID if the response time is less than 5 seconds after the SIS is powered up.The SIS will continually communicate a status message to the
SDM. The SDM can reset the SIS by removing and applying power to it.

CONDITIONS FOR RUNNING THE DTC


^ Ignition 1 voltage is within the normal operating voltage range.
^ The SDM monitors the inflatable restraint side impact sensor loop with the ignition ON.

CONDITIONS FOR SETTING THE DTC


The SDM has received an ID message from the SIS that does not match the ID stored in the SDM memory.

ACTION TAKEN WHEN THE DTC SETS


^ The SDM commands ON the AIR BAG warning lamp via Class 2 serial data.
^ The SDM attempts to reset the SIS.

CONDITIONS FOR CLEARING THE DTC


^ Current DTC
- The SDM has detected correct operation.
- The SIS sends an OK message to the SDM.
^ History DTC
- You issue a scan tool CLEAR CODES command.
- Once 255 malfunctions free ignition cycles have occurred.

DIAGNOSTIC AIDS
DTC B0079 is an indication that the incorrect inflatable restraint side impact sensor (SIS) is installed in the vehicle. Check to make sure that the
correct SIS is installed in the vehicle.

TEST DESCRIPTION

Diagnostic Chart

The following numbers refer to the step numbers in the diagnostic table:
2. This test checks the communication status of the inflatable restraint side impact sensor.

B0080
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 214
Chevrolet Venture V6-3.4L VIN E 1894

Schematic

CIRCUIT DESCRIPTION
When you first turn ON the ignition, the inflatable restraint Sensing and Diagnostic Module (SDM) performs tests to diagnose critical
malfunctions within itself. The SDM provides input power to the inflatable restraint Side Impact Sensor (SIS). When input power is first
detected, the SIS responds by performing internal diagnostics. Next the SIS sends an ID message to the SDM. The SDM will consider this to be a
valid ID if the response time is less than 5 seconds after the SIS is powered up.The SIS will continually communicate a status message to the
SDM. The SDM can reset the SIS by removing and applying power to it.

CONDITIONS FOR RUNNING THE DTC


^ Ignition 1 voltage is within the normal operating voltage range.
^ The SDM monitors the inflatable restraint side impact sensor loop with the ignition ON.

CONDITIONS FOR SETTING THE DTC


The SDM has received a NOK (not OK) message from the SIS.

ACTION TAKEN WHEN THE DTC SETS


The SDM commands ON the AIR BAG warning lamp via Class 2 serial data.

CONDITIONS FOR CLEARING THE DTC


^ You can issue a clear codes command. However, the DTC will appear again in the next ignition cycle.
^ Replace the inflatable restraint side impact sensor (SIS).

DIAGNOSTIC AIDS
DTC B0080 is an indication of an internal failure within the SIS.

TEST DESCRIPTION

Diagnostic Chart
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 215
Chevrolet Venture V6-3.4L VIN E 1895

The following numbers refer to the step numbers in the diagnostic table:
2. This test checks the communication status of the inflatable restraint side impact sensor.

B0081

Schematic

CIRCUIT DESCRIPTION
When you first turn ON the ignition, the inflatable restraint Sensing and Diagnostic Module (SDM) performs tests to diagnose critical
malfunctions within itself. The SDM provides input power to the inflatable restraint Side Impact Sensor (SIS). When input power is first
detected, the SIS responds by performing internal diagnostics. Next the SIS sends an ID message to the SDM. The SDM will consider this to be a
valid ID if the response time is less than 5 seconds after the SIS is powered up.The SIS will continually communicate a status message to the
SDM. The SDM can reset the SIS by removing and applying power to it.

CONDITIONS FOR RUNNING THE DTC


^ Ignition 1 voltage is within the normal operating voltage range.
^ The SDM monitors the inflatable restraint side impact sensor loop with the ignition ON.

CONDITIONS FOR SETTING THE DTC


The SDM has received an ID message from the SIS that does not match the ID stored in the SDM memory.

ACTION TAKEN WHEN THE DTC SETS


^ The SDM commands ON the AIR BAG warning lamp via Class 2 serial data.
^ The SDM attempts to reset the SIS.

CONDITIONS FOR CLEARING THE DTC


^ Current DTC
- The SDM has detected correct operation.
- The SIS sends an OK message to the SDM.
^ History DTC
- You issue a scan tool CLEAR CODES command.
- Once 255 malfunctions free ignition cycles have occurred.

DIAGNOSTIC AIDS
DTC B0081 is an indication that the incorrect inflatable restraint side impact sensor (SIS) is installed in the vehicle. Check to make sure that the
correct SIS is installed in the vehicle.

TEST DESCRIPTION
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 216
Chevrolet Venture V6-3.4L VIN E 1896

Diagnostic Chart

The following numbers refer to the step numbers in the diagnostic table:
2. This test checks the communication status of the inflatable restraint side impact sensor.

B0082

Schematic

CIRCUIT DESCRIPTION
When you first turn ON the ignition, the inflatable restraint Sensing and Diagnostic Module (SDM) performs tests to diagnose critical
malfunctions within itself. The SDM provides input power to the inflatable restraint Side Impact Sensor (SIS). When input power is first
detected, the SIS responds by performing internal diagnostics. Next the SIS sends an ID message to the SDM. The SDM will consider this to be a
valid ID if the response time is less than 5 seconds after the SIS is powered up.The SIS will continually communicate a status message to the
SDM. The SDM can reset the SIS by removing and applying power to it.

CONDITIONS FOR RUNNING THE DTC


^ Ignition 1 voltage is within the normal operating voltage range.
^ The SDM monitors the inflatable restraint side impact sensor loop with the ignition ON.

CONDITIONS FOR SETTING THE DTC


The SDM has received a NOK (not OK) message from the SIS.

ACTION TAKEN WHEN THE DTC SETS


The SDM commands ON the AIR BAG warning lamp via Class 2 serial data.

CONDITIONS FOR CLEARING THE DTC


^ You can issue a clear codes command. However, the DTC will appear again in the next ignition cycle.
^ Replace the inflatable restraint side impact sensor (SIS).
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 217
Chevrolet Venture V6-3.4L VIN E 1897

DIAGNOSTIC AIDS
DTC B0080 is an indication of an internal failure within the SIS.

TEST DESCRIPTION

Diagnostic Chart

The following numbers refer to the step numbers in the diagnostic table:
2. This test checks the communication status of the inflatable restraint side impact sensor.

B0160
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 218
Chevrolet Venture V6-3.4L VIN E 1898

Diagnostic Chart

Schematic

CIRCUIT DESCRIPTION
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 219
Chevrolet Venture V6-3.4L VIN E 1899
The Driver Information Display (DID) applies 5 volts to the ambient air temperature sensor. The ambient air temperature sensor is a thermistor
which varies in resistance as the temperature changes. As the resistance of the ambient air temperature sensor increases, the DID senses a larger
voltage drop across the sensor, indicating a lower temperature. As the resistance of the ambient air temperature sensor decrease, the DID senses a
smaller voltage drop across the sensor, indicating a higher temperature.

CONDITIONS FOR RUNNING THE DTC


The DID must be fully operational within a continuous voltage supply of 9.0 to 16.0 volts.

CONDITIONS FOR SETTING THE DTC


The sensed temperature must be greater than 140 Degrees Celsius for more than 2 seconds.

ACTION TAKEN WHEN THE DTC SETS


SC is displayed by the DID in the compass/temperature mode when the condition is present.

CONDITIONS FOR CLEARING THE DTC


^ DTC B0160 status changes from current to history when the condition is no longer present.
^ History DTC B0160 will clear after 100 consecutive fault free ignition cycles.
^ The DTC can be cleared with a scan tool.

TEST DESCRIPTION
The number(s) below refer to the step number(s) on the diagnostic table.
3. Tests for the proper operation of the circuit in the high voltage range.

B0162
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 220
Chevrolet Venture V6-3.4L VIN E 1900

Diagnostic Chart
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 221
Chevrolet Venture V6-3.4L VIN E 1901

Schematic

CIRCUIT DESCRIPTION
The Driver Information Display (DID) applies 5 volts to the ambient air temperature sensor. The ambient air temperature sensor is a thermistor
which will vary in resistance with temperature change. As the resistance of the ambient air temperature sensor increases, the DID senses a larger
voltage drop across the sensor, indicating a lower temperature. As the resistance of the ambient air temperature sensor decreases, the DID senses
a small voltage drop across the sensor, indicating a higher temperature.

CONDITIONS FOR RUNNING THE DTC


The DID must be fully operational within a continuous voltage supply of 9.0 to 16.0 volts.

CONDITIONS FOR SETTING THE DTC


The sensed temperature must be less than -40°F for more than 2 seconds.

ACTION TAKEN WHEN THE DTC SETS


OC is displayed by the DID in compass/temperature mode when the condition is present.

CONDITIONS FOR CLEARING THE DTC


^ DTC B0162 will become history when the DID no longer detects a failure.
^ History DTC B0162 will clear after 100 fault free ignition cycles.
^ The DTC can be cleared with a scan tool.

TEST DESCRIPTION
The number(s) below refer to the step number(s) on the diagnostic table.
4. Tests for the proper operation of the circuit in the low voltage range. If the fuse in the jumper opens when you perform this test, the signal
circuit is shorted to voltage.

B0931
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 222
Chevrolet Venture V6-3.4L VIN E 1902

Diagnostic Chart

CIRCUIT DESCRIPTION
The internal fault detection is handled by the Driver Information Display (DID).

CONDITIONS FOR RUNNING THE DTC


The DID monitors the analog input value once every ignition cycle at power up.

CONDITIONS FOR SETTING THE DTC


When the DID does not detect the compass sensor. This may be due to a faulty sensor that is not connected to the DID.

ACTION TAKEN WHEN THE DTC SETS


The DTC will be set and stored in non-volatile memory.

CONDITIONS FOR CLEARING THE DTC


^ The DTC will become history when a power cycle has been performed and the fault is not detected by the DID.
^ A history DTC will clear after 100 fault free ignition cycles.
^ A scan tool may be used to clear the DTC.

DIAGNOSTIC AIDS
If this DTC is retrieved as both a Current and History DTC, replace the DID.

B1000

Diagnostic Chart

CIRCUIT DESCRIPTION
The internal fault detection is handled inside the control module. No external circuits are involved.

CONDITIONS FOR RUNNING THE DTC


The control module runs a program to detect an internal fault when power up is commanded. The only requirements are voltage and ground.

CONDITIONS FOR SETTING THE DTC


^ The control module detects an internal memory (write error) malfunction.
^ The control module detects an internal memory (checksum error) malfunction.

ACTION TAKEN WHEN THE DTC SETS


The microprocessor refuses All additional inputs.
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 223
Chevrolet Venture V6-3.4L VIN E 1903

CONDITIONS FOR CLEARING THE DTC


^ The current DTC B1000 will clear when the microprocessor makes a successful write to the EEPROM and check sum maneuver.
^ A history DTC B1000 will clear after 100 consecutive ignition cycles if the condition for the malfunction is no longer present.
^ A scan tool may be used to clear the DTC.

DIAGNOSTIC AIDS
^ This DTC may be stored as a history DTC with out affecting the operation of the module. If stored only as a history DTC and not retrieved as
a current DTC, do not replace the module.
^ If this DTC is retrieved as both a Current and History DTC, replace the module.

Entertainment Systems Diagnosis

Diagnostic Chart

CIRCUIT DESCRIPTION
Each time the ignition cycles from OFF to ON, the radio receives VIN data over the class 2 communication circuit. If the VIN data in the radio
memory matches the VIN data it receives over the class 2 communication circuit, the radio will operate normally.

CONDITIONS FOR RUNNING THE DTC


^ The DTC is run when the radio is turned from OFF to ON.
^ Battery voltage is between 9 and 16 volts.

CONDITIONS FOR SETTING THE DTC


Installing a radio from a different vehicle platform or installing a new Powertrain Control Module (PCM) and not entering the correct setup
information with the scan tool.

ACTION TAKEN WHEN THE DTC SETS


The radio does not function. The radio displays "CAL".

CONDITIONS FOR CLEARING THE DTC


^ Installing a radio from another vehicle of the same platform or a new radio of the same platform.
^ Installing a new PCM setup properly with the correct VIN for that vehicle.
The DTC status will turn to history when the above criteria is met. The scan tool can now clear the history DTC or it will automatically clear
after 100 consecutive fault free ignition cycles.

TEST DESCRIPTION
The number(s) below refer to the step number(s) on the diagnostic table.
2. Clear all DTCs and cycle the ignition to check that the DTC did not falsely set.
3. Clear all DTCs after the repair procedure is complete.

Restraint System Diagnosis


CIRCUIT DESCRIPTION
When you first turn ON the ignition, the inflatable restraint Sensing and Diagnostic Module (SDM) compares the restraints ID that is stored in
the SDM to the restraints ID that is stored in the IPC. The restraints ID that is being compared contains the last tour digits of the SDM pan
number. Next, the SDM compares the VIN that is stored in the SDM to the VIN that is stored in the IPC. For more detailed information
concerning the Class 2 data lines, refer to Data Link Communications Circuit Description in Data Link Communications.

CONDITIONS FOR RUNNING THE DTC


Ignition 1 voltage is within the normal operating voltage range.

CONDITIONS FOR SETTING THE DTC


The restraints ID that is stored in the SDM does not match the restraints ID that is stored in the IPC or the VIN information that is stored in the
SDM does not match the VIN information that is stored in the IPC. This test is only run once during power up initialization.
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 224
Chevrolet Venture V6-3.4L VIN E 1904

ACTION TAKEN WHEN THE DTC SETS


^ The SDM commands ON the AIR BAG warning lamp via Class 2 serial data.
^ The SDM disables all deployments.

CONDITIONS FOR CLEARING THE DTC


The restraints ID that is stored in the SDM matches the restraints ID that is stored in the IPC and the VIN information that is stored in the SDM
matches the VIN information that is stored in the IPC.

DIAGNOSTIC AIDS
DTC B1001 is an indication that the restraints ID's stored in both the IPC and SDM do not match or that the VIN's stored in both the IPC and
SDM do not match. If either the IPC and/or PCM were replaced, the replacement modules need to be reprogrammed for proper operation.

TEST DESCRIPTION

Diagnostic Chart

The number(s) below refer to the step number(s) on the diagnostic table.
2. This step checks to see if the correct VIN is programmed in the powertrain control module (PCM).
4. This step checks to see if the Instrument Panel Cluster (IPC) has been replaced.
5. This step explains the proper steps to perform after an IPC has been replaced in order for the IPC to operate properly.
6. This step checks to see if the correct VIN is programmed in the IPC.
7. This step explains how to properly program the VIN into the IPC.
B1004
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 225
Chevrolet Venture V6-3.4L VIN E 1905

Diagnostic Chart

CIRCUIT DESCRIPTION
The microprocessor uses no external circuits for the operation that sets this DIC. The calculations that determine if this DTC is set are all internal
to the processor.

CONDITIONS FOR RUNNING THE DTC


The module microprocessor must be active/awake.

CONDITIONS FOR SETTING THE DTC


The microprocessor calculates a check sum on those areas of memory that hold critical operation data. This is done at a regular interval and is
called the periodic check sum. The microprocessor also calculates a check sum on these memory locations when ever new data is written to them.
This is called the running check sum. The microprocessor compares the periodic check sum to the running check sum. If they do not match, the
microprocessor sets the DTC.

ACTION TAKEN WHEN THE DTC SETS


The microprocessor reverts back to the base programmed critical operating data until new data is learned and stored in KAM.

CONDITIONS FOR CLEARING THE MIL/DTC


The DTC will clear when the microprocessor calculates a successful comparison of the periodic check sum to the running check sum.

DIAGNOSTIC AIDS
^ This DTC may be stored as a history DTC with out affecting the operation of the module. If stored only as a history DTC and not retrieved as
a current DTC, do not replace the module.
^ This DTC will never set as current during testing unless there is a non-recoverable memory failure.
^ Intermittent interruptions to either the Hot At All Times supply or the processor ground will cause the module to set the DTC.
^ If this DTC is retrieved as both a current and history DTC, replace the module.

B1440
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 226
Chevrolet Venture V6-3.4L VIN E 1906

Diagnostic Chart (Part 1 of 2)

Diagnostic Chart (Part 2 of 2)


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 227
Chevrolet Venture V6-3.4L VIN E 1907

Schematic

CIRCUIT DESCRIPTION
Class 2 communications will not start until the vehicle systems "on" power mode has been identified. Three discrete wires from the ignition
switch contacts are monitored by the Instrument Cluster (IPC) in order to determine the present power mode (ignition switch position). The IPC
communicates the system power mode to all class 2 modules on the class 2 serial data line.

CONDITIONS FOR RUNNING THE DTC


The IPC must be powered.

CONDITIONS FOR SETTING THE DTC


One of the three monitored ignition switch circuits has malfunctioned.

ACTION TAKEN WHEN THE DTC SETS


The IPC implements default actions for each ignition switch position when faults are detected.

CONDITIONS FOR CLEARING THE DTC


The power moding malfunction must be corrected and then the code can be cleared by using the scan tool. The code also clears after 100 ignition
cycles.

B2734

Diagnostic Chart
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 228
Chevrolet Venture V6-3.4L VIN E 1908
CIRCUIT DESCRIPTION
The non volatile memory check sum and write error detection is handled inside the control module. No external circuits are involved.

CONDITIONS FOR RUNNING THE DTC


The microprocessor runs the program to detect a check sum error after each "power up". This program runs only if the DTC B1327 is not set as
current DTCs.

CONDITIONS FOR SETTING THE DTC


The microprocessor sets this DTC if it can not write to non volatile memory. The DTC is also set if the microprocessor can not run an accurate
check sum on the non volatile memory.

ACTION TAKEN WHEN THE DTC SETS


The VTD module will store a code B2734 and no driver warning message will be displayed.

CONDITIONS FOR CLEARING THE MIL/DTC


The DTC clears when the microprocessor runs either a successful check sum test or a successful write to the non volatile memory.

DIAGNOSTIC AIDS
^ This DTC may be stored as a History DTC with out affecting the operation of the module. If stored only as a History DTC and not retrieved
as a current DTC, do not replace the module.
^ If this DTC is retrieved as both a Current and History DTC, replace the module.

TEST DESCRIPTION
The numbers below refer to the step numbers on the diagnostic table.
1. Be sure that the original ignition key issued with the vehicle is used when performing the Vehicle Theft Deterrent Diagnostic System Check.
3. The Vehicle Theft Deterrent (VTD) module must be programmed to the vehicle.

B2823

Diagnostic Chart

CIRCUIT DESCRIPTION
The Instrument Panel Cluster (IPC) contains a momentary switch that controls the trip odometer reset and trip season display options. The IPC
monitors the circuit voltage levels and detects when the Trip odometer reset switch has been depressed.

CONDITIONS FOR RUNNING THE DTC


The PC must have normal operating battery voltage.

CONDITIONS FOR SETTING THE DTC


The IPC detects that the trip reset switch input is low (grounded) for greater than 60 seconds.

ACTION TAKEN WHEN THE DTC SETS


The IPC will disable (ignore) the trip reset switch.

CONDITIONS FOR CLEARING THE DTC


^ A current DTC B2823 will clear after a complete ignition cycle.
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 229
Chevrolet Venture V6-3.4L VIN E 1909
^ A scan tool may be used to clear the DTC.

DIAGNOSTIC AIDS
^ The IPC will store the code as current only as long as the failure exists. An Intermittent failure will be stored as a history DTC B2823.
^ If DTC B2823 is set only in history, press and release the trip reset switch several times in order to verify the customer concern.

B2960

Diagnostic Chart
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 230
Chevrolet Venture V6-3.4L VIN E 1910

Theft Deterrent System Schematics (Pass Key III Module)

CIRCUIT DESCRIPTION
When an ignition key is inserted into the ignition lock cylinder, the transponder embedded in the head of the key is energized by the exciter coils
surrounding the ignition lock cylinder. The energized transponder transmits a signal that contains its unique value, which is received by the VTD
(Pass Key III(R)) Module. The VTD (Pass key III(R)) Module then compares this value to a value stored in memory (learned key code). If the
value is correct the VTD (Pass key III(R)) Module sends the enable password via the class 2 serial data circuit to the PCM.

CONDITIONS FOR RUNNING THE DTC


The ignition switch must be in RUN.

CONDITIONS FOR SETTING THE DTC


If the code from the ignition key does not match one stored in memory, the VTD (Pass key III(R)) Module sets this DTC. This code indicates the
use of a key with a transponder that has not been learned by the VTD (Pass Key III(R)) Module. The vehicle considers this to be a theft attempt.
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 231
Chevrolet Venture V6-3.4L VIN E 1911

ACTION TAKEN WHEN THE DTC SETS


^ The VTD (Pass Key III(R)) Module sends a class 2 message containing a disable password to the PCM.
^ The vehicle will not start.
^ The VTD (Pass key III(R)) Module sends a class 2 message to the instrument cluster to flash the SECURITY indicator.

CONDITIONS FOR CLEARING THE MIL/DTC


The VTD (Pass Key III(R)) Module clears the current status of the DTC when it senses a valid, memorized, key code from the ignition key
(transponder).

TEST DESCRIPTION
The numbers below refer to the step numbers on the diagnostic table.
2. To set this code, a key with a working transponder was read by the VTD (Pass Key III(R)) Module. For that key to operate the vehicle a 10
Minute or 30 Minute Re-Learn Procedure must be performed.

B3031

Diagnostic Chart
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 232
Chevrolet Venture V6-3.4L VIN E 1912

Theft Deterrent System Schematics (Pass Key III Module)

CIRCUIT DESCRIPTION
The Vehicle Theft Deterrent (VTD) module checks memory to see if the Learn Coded Key setting is on. If so, the VTD sets this DTC.

RUNNING THE DTC


The VTD must see the ignition switch input. The VTD can not have a B1327 set as a current DTC.

CONDITIONS FOR SETTING THE DTC


If the Learn Coded Key setting is on, the VTD sets this DTC.

ACTION TAKEN WHEN THE DTC SETS


The VTD will learn the key code. No driver warning message will be displayed for this DTC.

CONDITIONS FOR CLEARING THE MIL/DTC


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 233
Chevrolet Venture V6-3.4L VIN E 1913
The VTD clears the current status of the DTC when it does not see the Learn Coded Key setting as on. The DTC will still be retrieved as current
until the ignition switch is cycled. The DTC will become a history DTC at that time.

TEST DESCRIPTION
The numbers below refer to the step numbers on the diagnostic table.
2. To set this code, a key with a working transponder was read by the VTD (Pass Key III(R)) Module. For that key to operate the vehicle a 10
Minute or 30 Minute Re-Learn Procedure must be performed.

B3055

Diagnostic Chart
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 234
Chevrolet Venture V6-3.4L VIN E 1914

Theft Deterrent System Schematics (Pass Key III Module)

CIRCUIT DESCRIPTION
When an ignition key is inserted into the ignition lock cylinder, the transponder embedded in the head of the key is energized by the exciter coils
surrounding the ignition lock cylinder. The energized transponder transmits a signal that contains its unique value, which is received by the VTD
(Pass Key III(R)) Module. The VTD (Pass Key III(R)) Module then compares this value to a value stored in memory (learned key code). If the
value is correct the VTD (Pass Key III(R)) Module sends the enable password via the class 2 serial data circuit to the PCM.

CONDITIONS FOR RUNNING THE DTC


The ignition switch must be in RUN. The VTD (Pass Key III(R)) Module cannot have a current DTC B1327.

CONDITIONS FOR SETTING THE DTC


The VTD (Pass Key III(R)) Module is unable to measure the ignition key transponder value for one second. This may be due to a damaged or
missing transponder pellet, a non Pass Key III(R) key, or a damaged exciter. If the conditions occur after the engine is running, setting the DTC
may take up to 30 seconds. See Important below.
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 235
Chevrolet Venture V6-3.4L VIN E 1915

ACTION TAKEN WHEN THE DTC SETS

IMPORTANT: If the VTD (Pass Key III(R)) Module is unable to measure the ignition key transponder value for 30 consecutive seconds, after
the vehicle has started, the module will enter a fail enable state. The vehicle will not stall or stop running. If the VTD (Pass Key III(R)) Module
is in a fail enable state when the ignition is turned to OFF, it will remain "fail enabled" until the next time the vehicle is started. If the VTD (Pass
Key III(R)) Module is "fail enabled" the Pass Key III(R) system is NOT active and the vehicle will start. The module WILL send its enable
password even if a transponder value is not received. The VTD (Pass Key III(R)) Module will remain "fail enabled" until it measures a valid key
transponder value.
1. The VTD (Pass Key III(R)) Module sends a class 2 message containing a disable password to the PCM.
2. The vehicle will not start.
3. The VTD (Pass Key III(R)) Module sends a class 2 message to the instrument cluster to illuminate the SECURITY indicator on steady.

CONDITIONS FOR CLEARING THE MIL/DTC


The VTD clears the current status of the DTC when it senses a key code from the exciter. If the code is not from a learned key, a DTC B2960
will be set.

TEST DESCRIPTION
The numbers below refer to the step numbers on the diagnostic table:
2. The key must be a Pass Key III(R) transponder key with an operating transponder for the system to work.
3. The only method to confirm whether the transponder in the key or the VTD (Pass Key III(R)) Module is malfunctioning is to try a alternative
component in the system. The vehicle was delivered with four keys.
4. It is unlikely that more than one key will be defective. If all keys do not work, the VTD (Pass Key III(R)) Module must be malfunctioning.
5. If the vehicle has a malfunctioning VTD (Pass Key III(R)) Module that malfunctioned during an ignition cycle, the system will be "fail
enabled" and the vehicle will start for all keys. In this case the code B3055 will remain set and be current for all keys.
7. If a new key must be tried, it must have the proper mechanical cut and the VTD (Pass Key III(R)) Module must "learn" the transponder
value.
8. If only one key was available for the vehicle and the replacement key does not work, the VTD (Pass Key III(R)) Module must be
malfunctioning.

All Other P Codes


If the P code is not listed, then:

- Either the code may not be valid for this vehicle or year.
- Or the information published by the OEM does not include this code for this vehicle or year.
- Or ALLDATA has not added the information for this code yet.
P0101
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 236
Chevrolet Venture V6-3.4L VIN E 1916

Diagnostic Chart (Part 1 Of 2)


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 237
Chevrolet Venture V6-3.4L VIN E 1917

Diagnostic Chart (Part 2 Of 2)


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 238
Chevrolet Venture V6-3.4L VIN E 1918

Engine Controls Schematics: Engine Data Sensors, MAF, EVAP Switch, EVAP Valve, EGR

CIRCUIT DESCRIPTION
The Mass Air Flow (MAF) sensor measures the amount of air which passes through it into the engine. The PCM uses the mass air flow
information to monitor engine operating conditions for fuel delivery calculations. A large quantity of air entering the engine indicates an
acceleration or high load situation, while a small quantity of air indicates deceleration or idle.

The MAF sensor produces a frequency signal which can be monitored using a scan tool. The frequency will vary within a range of around 2000
Hertz at idle to near 8000 Hertz at maximum engine load. DTC P0101 will be set if the signal from the MAF sensor does not match a predicted
value based on barometric pressure, air density, manifold pressure, throttle position and engine RPM.

CONDITIONS FOR RUNNING THE DTC


- The engine is running.
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 239
Chevrolet Venture V6-3.4L VIN E 1919
- The ignition voltage between 9.0 and 18.0 volts.
- The throttle angle less than 50 percent.
- The MAP and TP steady for more than 10 seconds.
- The EGR duty cycle is below 50 percent.
- The EGR pintle position is below 50 percent.

CONDITIONS FOR SETTING THE DTC


The difference between actual airflow and predicted airflow is more than a calibrated value.

ACTION TAKEN WHEN THE DTC SETS


- The PCM will illuminate the Malfunction Indicator Lamp (MIL) during the second consecutive trip in which the diagnostic has been run and
failed.
- If equipped with traction control, the PCM will command the Electronic Brake And Traction Control Module (EBTCM) via the serial data
circuit to turn OFF traction control, and the EBTCM will illuminate the TRACTION OFF lamp.
- The PCM will store conditions which were present when the DTC set as Freeze Frame and Failure Records data.

CONDITIONS FOR CLEARING THE MIL/DTC


- The PCM will turn OFF the MIL during the third consecutive trip in which the diagnostic has been run and passed.
- The History DTC will clear after 40 consecutive warm-up cycles have occurred without a malfunction.
- The DTC can be cleared by using a scan tool.

DIAGNOSTIC AIDS
Inspect for the following conditions:
- Skewed or stuck TP sensor. - A faulty TP sensor or TP sensor circuit can cause the PCM to incorrectly calculate the predicted mass air flow
value. Observe throttle angle with the throttle closed. If the throttle angle reading is not 0 percent, check for the following conditions and
repair as necessary:
- The TP sensor signal circuit shorted to voltage. Refer to Wiring Repairs in Diagrams.
- A poor connection or high resistance in the TP sensor ground circuit. Refer to Testing for Intermittent and Poor Connections in Diagrams.
- If none of the above conditions are noted and the throttle angle reading at closed throttle is not 0 percent, replace the TP sensor.
- A skewed MAP sensor.- A skewed MAP sensor can cause the BARO reading to be incorrectly calculated. To check the MAP sensor,
compare the MAP/BARO reading on the vehicle being diagnosed to the MAP/BARO reading on a normally operating vehicle. If a large
difference is noted replace the MAP sensor.
- Misrouted harness.- Inspect the MAF sensor harness to ensure that it is not routed too close to high voltage wires such as spark plug leads.
- Plugged intake air duct or dirty air filter element.
- The actual mass air flow is compared to a calculated mass air flow based on the MAP, TP, and engine RPM readings (speed density). A
skewed/unresponsive MAP sensor at key ON will cause the calculated mass air flow value to be inaccurate. When the engine is started a
calculated difference between actual mass air flow and Calculated mass air flow occurs. DTC P0101 will set, the vehicle will stall, a default
mass air flow based on the MAP sensor will occur. Because the MAP sensor is skewed/unresponsive the default mass air flow values are
incorrect and vehicle may not restart. If a fault occurs which causes the MAP sensor value to be incorrect (poor vacuum connections,
damaged vacuum source, or defective vacuum hoses, unmetered air into the manifold), DTC P0101 will set and the default mass airflow
value will be substituted. Because the MAP sensor value is incorrect the vehicle may not start and run.

IMPORTANT: Remove any debris from the connector surfaces before servicing a component. Inspect the connector gaskets when diagnosing
or replacing a component. Ensure that the gaskets are installed correctly. The gaskets prevent contaminate intrusion.

- Poor terminal connection-Inspect the harness connectors for backed out terminals, improper mating, broken locks, improperly formed or
damaged terminals, and faulty terminal to wire connection. Use a corresponding mating terminal to test for proper tension. Refer to
Diagrams.
- Damaged harness-Inspect the wiring harness for damage. If the harness inspection does not reveal a problem, observe the display on the scan
tool while moving connectors and wiring harnesses related to the sensor. A change in the scan tool display may indicate the location of the
fault. Refer to Diagrams.
- PCM and engine grounds for clean and secure connections

If the DTC is determined to be intermittent, reviewing the Failure Records can be useful in determining when the DTC was last set.

TEST DESCRIPTION
The numbers below refer to the step numbers on the diagnostic table:
3. Only, if sent here from the Engine Cranks But Does Not Run, continue to follow diagnostic table even if DTC P0101 has NOT failed this
ignition.
4. This step tests the MAP sensor. By disconnecting the MAF sensor, the vehicle is forced into speed density. Speed density is based on the
MAP, throttle position, and engine RPM readings. With a skewed or unresponsive MAP sensor, the speed density calculation is incorrect and
vehicle may not start. For further information refer to diagnostic aids.
5. This step tests for a skewed or sticking MAP sensor. The MAP sensor should respond smoothly and gradually as RPM is increased. Compare
MAP the sensor of the affected vehicle to that of a normally operating vehicle if a large difference is noted replace the MAP sensor.
9. Verifies that ignition feed voltage and a good ground are available at the MAF sensor.

P0102
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 240
Chevrolet Venture V6-3.4L VIN E 1920

Diagnostic Chart (Part 1 Of 2)


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 241
Chevrolet Venture V6-3.4L VIN E 1921

Diagnostic Chart (Part 2 Of 2)


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 242
Chevrolet Venture V6-3.4L VIN E 1922

Engine Controls Schematics: Engine Data Sensors, MAF, EVAP Switch, EVAP Valve, EGR

CIRCUIT DESCRIPTION
The Mass Air Flow (MAF) sensor measures the amount of air which passes through it into the engine. The PCM uses the mass air flow
information to monitor engine operating conditions for fuel delivery calculations. A large quantity of air entering the engine indicates an
acceleration or high load situation, while a small quantity of air indicates deceleration or idle. The MAF sensor produces a frequency signal
which can be monitored using a scan tool. The frequency will vary within a range of around 2000 Hertz at idle to about 10,000 Hertz at
maximum engine load. DTC P0102 will be set if the signal frequency from the MAF sensor is lower than the possible range of a normally
operating MAF sensor.

CONDITIONS FOR RUNNING THE DTC


- The engine is running.
- The throttle angle is below 50 percent.
- The ignition voltage is more than 8.0 volts.
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 243
Chevrolet Venture V6-3.4L VIN E 1923

CONDITIONS FOR SETTING THE DTC


- The MAF signal frequency is below 1200 Hertz.
- The above conditions are present for over 0.5 seconds.

ACTION TAKEN WHEN THE DTC SETS


- The PCM will illuminate the Malfunction Indicator Lamp (MIL) during the second consecutive trip in which the diagnostic has been run and
failed.
- If equipped with traction control, the PCM will command the Electronic Brake And Traction Control Module (EBTCM) via the serial data
circuit to turn OFF traction control, and the EBTCM will illuminate the TRACTION OFF lamp.
- The PCM will store conditions which were present when the DTC set as Freeze Frame and Failure Records data.

CONDITIONS FOR CLEARING THE MIL/DTC


- The PCM will turn OFF the MIL during the third consecutive trip in which the diagnostic has been run and passed.
- The History DTC will clear after 40 consecutive warm-up cycles have occurred without a malfunction.
- The DTC can be cleared by using a scan tool.

DIAGNOSTIC AIDS
Inspect for the following conditions:

Plugged intake air duct or filter element. A wide-open throttle acceleration from a stop should cause the mass air flow displayed on a scan tool to
increase from about 4-6 gm/s at idle to 100 gm/s or more at the time of the 1-2 shift. If not, check for a restriction.

IMPORTANT: Remove any debris from the connector surfaces before servicing a component. Inspect the connector gaskets when diagnosing
or replacing a component. Ensure that the gaskets are installed correctly. The gaskets prevent contaminate intrusion.

- Poor terminal connection-Inspect the harness connectors for backed out terminals, improper mating, broken locks, improperly formed or
damaged terminals, and faulty terminal to wire connection. Use a corresponding mating terminal to test for proper tension. Refer to
Diagrams.
- Damaged harness-Inspect the wiring harness for damage. If the harness inspection does not reveal a problem, observe the display on the scan
tool while moving connectors and wiring harnesses related to the sensor. A change in the scan tool display may indicate the location of the
fault. Refer to Diagrams.
- PCM and engine grounds for clean and secure connections

If the DTC is determined to be intermittent, reviewing the Failure Records can be useful in determining when the DTC was last set.

TEST DESCRIPTION
The numbers below refer to the Step numbers on the diagnostic table:
2. This step verifies that the problem is present at idle.
5. A voltage reading of less than 4.0 or over 6.0 volts at the MAF sensor signal circuit indicates a malfunction in the wiring or a poor
connection.
6. Verifies that ignition feed voltage and a good ground are available at the MAF sensor.
13. This vehicle is equipped with a PCM which utilizes an Electrically Erasable Programmable Read Only Memory (EEPROM). When the PCM
is being replaced, the new PCM must be programmed.

P0103
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 244
Chevrolet Venture V6-3.4L VIN E 1924

Diagnostic Chart
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 245
Chevrolet Venture V6-3.4L VIN E 1925

Engine Controls Schematics: Engine Data Sensors, MAF, EVAP Switch, EVAP Valve, EGR

CIRCUIT DESCRIPTION
The Mass Air Flow (MAF) sensor measures the amount of air which passes through it into the engine during a given time. The PCM uses the
mass air flow sensor information to monitor engine operating conditions for fuel delivery calculations. A large quantity of air entering the engine
indicates an acceleration or high load situation, while a small quantity of air indicates deceleration or idle.

The MAF sensor produces a frequency signal which can be monitored by using a scan tool. The frequency will vary within a range of around
2000 Hertz at idle to near 8,000 Hertz at maximum engine load. DTC P0103 will be set if the signal from the MAF sensor is above the possible
range of a normally operating MAF sensor.

CONDITIONS FOR RUNNING THE DTC


- The engine is running.
- Ignition voltage is more than 8.0 volts.
- The condition is present for 0.5 seconds.
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 246
Chevrolet Venture V6-3.4L VIN E 1926
- The IAC is more than 2 counts.

CONDITIONS FOR SETTING THE DTC


MAF signal frequency is above 11,500 Hertz (11.5 kHz).

ACTION TAKEN WHEN THE DTC SETS


- The PCM will illuminate the Malfunction Indicator Lamp (MIL) during the second consecutive trip in which the diagnostic has been run and
failed.
- If equipped with traction control, the PCM will command the Electronic Brake And Traction Control Module (EBTCM) via the serial data
circuit to turn OFF traction control, and the EBTCM will illuminate the TRACTION OFF lamp.
- The PCM will store conditions which were present when the DTC set as Freeze Frame and Failure Records data.

CONDITIONS FOR CLEARING THE MIL/DTC


- The PCM will turn OFF the MIL during the third consecutive trip in which the diagnostic has been run and passed.
- The History DTC will clear after 40 consecutive warm-up cycles have occurred without a malfunction.
- The DTC can be cleared by using a scan tool.

DIAGNOSTIC AIDS
Inspect for the following conditions:

IMPORTANT: Remove any debris from the connector surfaces before servicing a component. Inspect the connector gaskets when diagnosing
or replacing a component. Ensure that the gaskets are installed correctly. The gaskets prevent contaminate intrusion.

- Poor terminal connection-Inspect the harness connectors for backed out terminals, improper mating, broken locks, improperly formed or
damaged terminals, and faulty terminal to wire connection. Use a corresponding mating terminal to test for proper tension. Refer to
Diagrams.
- Damaged hamess-Inspect the wiring harness for damage. If the harness inspection does not reveal a problem, observe the display on the scan
tool while moving connectors and wiring harnesses related to the sensor. A change in the scan tool display may indicate the location of the
fault. Refer to Diagrams.
- PCM and engine grounds for clean and secure connections

If the DTC is determined to be intermittent, reviewing the Failure Records can be useful in determining when the DTC was last set.

TEST DESCRIPTION
The numbers below refer to the step numbers on the diagnostic table:
2. This step verifies that the problem is present at idle.
4. A frequency reading with the MAF sensor connector disconnected indicates an Electromagnetic Interference (EMI) related malfunction or a
poor connection.
9. This vehicle is equipped with a PCM which utilizes an Electrically Erasable Programmable Read Only Memory (EEPROM). When the PCM
is being replaced, the new PCM must be programmed.

P0107

Diagnostic Chart (Part 1 Of 2)


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 247
Chevrolet Venture V6-3.4L VIN E 1927

Diagnostic Chart (Part 2 Of 2)


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 248
Chevrolet Venture V6-3.4L VIN E 1928

Schematic

CIRCUIT DESCRIPTION
The Manifold Absolute Pressure (MAP) sensor responds to changes in intake manifold pressure (vacuum). The MAP sensor signal voltage to the
PCM varies from below 2 volts at idle (high vacuum) to above 4 volts with the key ON, engine not running or at wide-open throttle (low
vacuum). The MAP sensor is used to determine manifold pressure changes while the EGR flow test diagnostic is being run, refer to DTC P0401
Exhaust Gas Recirculation (EGR) Flow Insufficient. See: Diagnostic Trouble Code Tests and Associated Procedures/P Code Charts/P0401

Also to update the Barometric Pressure Reading (BARO), as an enabling factor for other diagnostics. The PCM monitors the map signals for
voltages outside the normal range of the MAP sensor. If the PCM detects a MAP sensor signal voltage that is excessively low, DTC P0107 will
set. See: Diagnostic Trouble Code Tests and Associated Procedures/P Code Charts/P0401

CONDITIONS FOR RUNNING THE DTC


- TP sensor DTCs are not present.
- System voltage more than 9 volts.
- The engine is running.
- Throttle angle is above 0 percent, if engine speed is less than 1000 RPM.
- Throttle angle is above 10 percent, if engine speed is more than 1000 RPM.

CONDITIONS FOR SETTING THE DTC


- The MAP sensor signal voltage is less than 0.1 volt (12 kPa).
- Above condition is present for longer than 200 3X reference periods (67 crankshaft revolutions).

ACTION TAKEN WHEN THE DTC SETS


- The PCM will illuminate the Malfunction Indicator Lamp (MIL) during the second consecutive trip in which the diagnostic test has been run
and failed.
- The PCM will store conditions which were present when the DTC set as Freeze Frame and Failure Records data.
- If the misfire is determined to be catalyst damaging, the PCM will flash the MIL.

CONDITIONS FOR CLEARING THE MIL/DTC


- The PCM will turn OFF the MIL during the third consecutive trip in which the diagnostic has been run and passed.
- The History DTC will clear after 40 consecutive warm-up cycles have occurred without a malfunction.
- The DTC can be cleared by using a scan tool.
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 249
Chevrolet Venture V6-3.4L VIN E 1929

DIAGNOSTIC AIDS
Inspect for the following conditions:

IMPORTANT: Remove any debris from the connector surfaces before servicing a component. Inspect the connector gaskets when diagnosing
or replacing a component. Ensure that the gaskets are installed correctly. The gaskets prevent contaminate intrusion.

- Poor terminal connection-Inspect the harness connectors for backed out terminals, improper mating, broken locks, improperly formed or
damaged terminals, and faulty terminal to wire connection. Use a corresponding mating terminal to test for proper tension. Refer to
Diagrams.
- Damaged harness-Inspect the wiring harness for damage. If the harness inspection does not reveal a problem, observe the display on the scan
tool while moving connectors and wiring harnesses related to the sensor. A change in the scan tool display may indicate the location of the
fault. Refer to Diagrams.
- PCM and engine grounds for clean and secure connections

If the DTC is determined to be intermittent, reviewing the Failure Records can be useful in determining when the DTC was last set.

TEST DESCRIPTION
The numbers below refer to the step numbers on the diagnostic table:
12. This vehicle is equipped with a PCM which utilizes an Electrically Erasable Programmable Read Only Memory (EEPROM). When the PCM
is being replaced, the new PCM must be programmed.

P0108
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 250
Chevrolet Venture V6-3.4L VIN E 1930

Diagnostic Chart
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 251
Chevrolet Venture V6-3.4L VIN E 1931

Schematic

CIRCUIT DESCRIPTION
The Manifold Absolute Pressure (MAP) sensor responds to changes in intake manifold pressure (vacuum). The MAP sensor signal voltage to the
PCM varies from below 2 volts at idle (high vacuum) to above 4 volts with the key ON, engine not running or at wide-open throttle (low
vacuum). The MAP sensor is used to determine manifold pressure changes while the EGR flow test diagnostic is being run, refer to DTC P0401
Exhaust Gas Recirculation (EGR) Flow Insufficient. See: Diagnostic Trouble Code Tests and Associated Procedures/P Code Charts/P0401

Also to update the Barometric Pressure Reading (BARO), as an enabling factor for other diagnostics. The PCM monitors the MAP signals for
voltages outside the normal range of the MAP sensor. If the PCM detects a MAP signal voltage that is excessively high, DTC P0108 will set.
See: Diagnostic Trouble Code Tests and Associated Procedures/P Code Charts/P0108

CONDITIONS FOR RUNNING THE DTC


- TP sensor DTCs are not present.
- System voltage is more than 9.0 volts.
- Engine has been running for a length of time that is determined by start-up coolant temperature. The length of time ranges from 2 minutes at
less than -30°C (-22°F) to 0.5 second at more than 30°C (86°F).
- Throttle position is below 2 percent if the engine speed is less than 3000 RPM.
- Throttle position is above 30 percent if the engine speed is more than 3000 RPM.

CONDITIONS FOR SETTING THE DTC


- The MAP sensor signal voltage is more than 4.2 volts.
- The above condition is present for longer than 200 3X reference periods (67 crankshaft revolutions).

ACTION TAKEN WHEN THE DTC SETS


- The PCM will illuminate the Malfunction Indicator Lamp (MIL) during the second consecutive trip in which the diagnostic test has been run
and failed.
- The PCM will store conditions which were present when the DTC set as Freeze Frame and Failure Records data.
- If the misfire is determined to be catalyst damaging, the PCM will flash the MIL.

CONDITIONS FOR CLEARING THE MIL/DTC


- The PCM will turn OFF the MIL during the third consecutive trip in which the diagnostic has been run and passed.
- The History DTC will clear after 40 consecutive warm-up cycles have occurred without a malfunction.
- The DTC can be cleared by using a scan tool.
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 252
Chevrolet Venture V6-3.4L VIN E 1932

DIAGNOSTIC AIDS
Inspect for the following conditions:

IMPORTANT: Remove any debris from the connector surfaces before servicing a component. Inspect the connector gaskets when diagnosing
or replacing a component. Ensure that the gaskets are installed correctly. The gaskets prevent contaminate intrusion.

- Poor terminal connection-Inspect the harness connectors for backed out terminals, improper mating, broken locks, improperly formed or
damaged terminals, and faulty terminal to wire connection. Use a corresponding mating terminal to test for proper tension. Refer to
Diagrams.
- Damaged harness-Inspect the wiring harness for damage. If the harness inspection does not reveal a problem, observe the display on the scan
tool while moving connectors and wiring harnesses related to the sensor. A change in the scan tool display may indicate the location of the
fault. Refer to Diagrams.
- PCM and engine grounds for clean and secure connections

If the DTC is determined to be intermittent, reviewing the Failure Records can be useful in determining when the DTC was last set.

TEST DESCRIPTION
The numbers below refer to the step numbers on the diagnostic table:
11. This vehicle is equipped with a PCM which utilizes an Electrically Erasable Programmable Read Only Memory (EEPROM). When the PCM
is being replaced, the new PCM must be programmed.

P0112

Diagnostic Chart
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 253
Chevrolet Venture V6-3.4L VIN E 1933

Schematic

CIRCUIT DESCRIPTION
The Intake Air Temperature (IAT) sensor is a thermistor which measures the temperature of the air entering the engine. The PCM applies 5.0
volts through a pull up resistor. When the intake air is cold, the sensor resistance is high and the PCM will monitor a high signal voltage on the
IAT sensor signal circuit. As the intake air warm, the sensor resistance becomes lower causing the PCM to monitor a lower voltage. If the PCM
detects an excessively low IAT sensor signal voltage (high temperature indicated), DTC P0112 will set.

CONDITIONS FOR RUNNING THE DTC


- Active ECT, MAF sensor or VSS DTCs are not present.
- Engine running for over 10 seconds.
- Vehicle speed is more than 40 km/h (25 mph).

CONDITIONS FOR SETTING THE DTC


- IAT signal voltage indicates an intake air temperature more than 135°C (275°F).
- The above condition is present for at least 20 seconds.

ACTION TAKEN WHEN THE DTC SETS


- The PCM will illuminate the Malfunction Indicator Lamp (MIL) during the second consecutive trip in which the diagnostic test has been run
and failed.
- The PCM will store conditions which were present when the DTC set as Freeze Frame and Failure Records data.
- If the misfire is determined to be catalyst damaging, the PCM will flash the MIL.

CONDITIONS FOR CLEARING THE MIL/DTC


- The PCM will turn OFF the MIL during the third consecutive trip in which the diagnostic has been run and passed.
- The History DTC will clear after 40 consecutive warm-up cycles have occurred without a malfunction.
- The DTC can be cleared by using a scan tool.

DIAGNOSTIC AIDS
Inspect for the following conditions:

IMPORTANT: Remove any debris from the connector surfaces before servicing a component. Inspect the connector gaskets when diagnosing
or replacing a component. Ensure that the gaskets are installed correctly. The gaskets prevent contaminate intrusion.

- Poor terminal connection-Inspect the harness connectors for backed out terminals, improper mating, broken locks, improperly formed or
damaged terminals, and faulty terminal to wire connection. Use a corresponding mating terminal to test for proper tension. Refer to
Diagrams.
- Damaged harness-Inspect the wiring harness for damage. If the harness inspection does not reveal a problem, observe the display on the scan
tool while moving connectors and wiring harnesses related to the sensor. A change in the scan tool display may indicate the location of the
fault. Refer to Diagrams.
- PCM and engine grounds for clean and secure connections

If the DTC is determined to be intermittent, reviewing the Failure Records can be useful in determining when the DTC was last set.

TEST DESCRIPTION
The number below refers to the step number on the diagnostic table:
2. Verifies that the fault is present.
3. If DTC P0112 can be repeated only by duplicating the Failure Records conditions. Refer to Temperature vs Resistance table. See:
Specifications/Electrical Specifications

The table may be used to test the IAT sensor at various temperatures to evaluate the possibility of a shifted sensor that may be shorted above or
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 254
Chevrolet Venture V6-3.4L VIN E 1934
below a certain temperature. If this is the case, replace the IAT sensor. If the IAT sensor appears to be OK, the fault is intermittent refer to
Diagnostic Aids.
7. This vehicle is equipped with a PCM which utilizes an Electrically Erasable Programmable Read Only Memory (EEPROM). When the PCM
is being replaced, the new PCM must be programmed. Refer to PCM Replacement/Programming. See: Powertrain Control Module

P0113

Diagnostic Chart
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 255
Chevrolet Venture V6-3.4L VIN E 1935

Schematic

CIRCUIT DESCRIPTION
The Intake Air Temperature (IAT) sensor is a thermistor which measures the temperature of the air entering the engine. The PCM applies 5.0 V
through a pull up resistor. When the intake air is cold, the sensor resistance is high and the PCM will monitor a high signal voltage on the IAT
sensor signal circuit. As the intake air warm, the sensor resistance becomes lower causing the PCM to monitor a lower voltage. If the PCM
detects an excessively high IAT sensor signal voltage (low temperature indicated), DTC P0113 will set.

CONDITIONS FOR RUNNING THE DTC


- Active ECT, MAF sensor or VSS DTC are not present.
- Vehicle speed is less than 56 km/h (35 mph).
- MAF is less than 12 gm/s.
- ECT is more than 60°C (140°F).
- The Engine run time is more than 3 minutes.

CONDITIONS FOR SETTING THE DTC


- IAT signal voltage indicates an intake air temperature less than -37°C (-35°F).
- The above conditions are present for at least 20 seconds.

ACTION TAKEN WHEN THE DTC SETS


- The PCM will illuminate the Malfunction Indicator Lamp (MIL) during the second consecutive trip in which the diagnostic test has been run
and failed.
- The PCM will store conditions which were present when the DTC set as Freeze Frame and Failure Records data.
- If the misfire is determined to be catalyst damaging, the PCM will flash the MIL.

CONDITIONS FOR CLEARING THE MIL/DTC


- The PCM will turn OFF the MIL during the third consecutive trip in which the diagnostic has been run and passed.
- The History DTC will clear after 40 consecutive warm-up cycles have occurred without a malfunction.
- The DTC can be cleared by using a scan tool.

DIAGNOSTIC AIDS
Inspect for the following conditions:

IMPORTANT: Remove any debris from the connector surfaces before servicing a component. Inspect the connector gaskets when diagnosing
or replacing a component. Ensure that the gaskets are installed correctly. The gaskets prevent contaminate intrusion.

- Poor terminal connection-Inspect the harness connectors for backed out terminals, improper mating, broken locks, improperly formed or
damaged terminals, and faulty terminal to wire connection. Use a corresponding mating terminal to test for proper tension. Refer to
Diagrams.
- Damaged harness-Inspect the wiring harness for damage. If the harness inspection does not reveal a problem, observe the display on the scan
tool while moving connectors and wiring harnesses related to the sensor. A change in the scan tool display may indicate the location of the
fault. Refer to Diagrams.
- PCM and engine grounds for clean and secure connections

If the DTC is determined to be intermittent, reviewing the Failure Records can be useful in determining when the DTC was last set.

TEST DESCRIPTION
The numbers below refer to the step numbers on the diagnostic table:
2. Verifies that the fault is present.
3. If DTC P0113 can be repeated only by duplicating the Failure Records conditions. The Temperature vs Resistance table may be used to test
the IAT sensor at various temperatures to evaluate the possibility of a shifted sensor that may be open above or below a certain temperature.
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 256
Chevrolet Venture V6-3.4L VIN E 1936
If this is the case, replace the IAT sensor. If the IAT sensor appears to be OK, the fault is intermittent. Refer to Diagnostic Aids.
5. Use a fused jumper during this test. It the IAT signal circuit is shorted to battery or ignition positive voltage the fuse in the jumper will open,
indicating a short in the signal circuit.
12. This vehicle is equipped with a PCM which utilizes an Electrically Erasable Programmable Read Only Memory (EEPROM). When the PCM
is being replaced, the new PCM must be programmed. Refer to PCM Replacement/Programming. See: Powertrain Control Module

P0117

Diagnostic Chart

Schematic

CIRCUIT DESCRIPTION
The Engine Coolant Temperature (ECT) sensor is a thermistor mounted in the engine coolant stream. The PCM applies a voltage (about 5.0
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 257
Chevrolet Venture V6-3.4L VIN E 1937
volts) through a pull up resistor to the ECT signal circuit. When the engine coolant is cold, the sensor (thermistor) resistance is high, therefore
the PCM will measure a high signal voltage. As the engine coolant warms, the sensor resistance becomes less, and the ECT signal voltage
measured at the PCM drops. With a fully warmed up engine, the ECT signal voltage should measure about 1.5-2.0 volts.

CONDITIONS FOR RUNNING THE DTC


The engine is running for 3 seconds.

CONDITIONS FOR SETTING THE DTC


- The ECT indicates an engine coolant temperature more than 140°C (283°F).
- Above condition present for longer than 25 seconds.

ACTION TAKEN WHEN THE DTC SETS


- The PCM will illuminate the Malfunction Indicator Lamp (MIL) during the second consecutive trip in which the diagnostic test has been run
and failed.
- The PCM will store conditions which were present when the DTC set as Freeze Frame and Failure Records data.
- If the misfire is determined to be catalyst damaging, the PCM will flash the MIL.

CONDITIONS FOR CLEARING THE MIL/DTC


- The PCM will turn OFF the MIL during the third consecutive trip in which the diagnostic has been run and passed.
- The History DTC will clear after 40 consecutive warm-up cycles have occurred without a malfunction.
- The DTC can be cleared by using a scan tool.

DIAGNOSTIC AIDS
Inspect for the following conditions:

IMPORTANT: Remove any debris from the connector surfaces before servicing a component. Inspect the connector gaskets when diagnosing
or replacing a component. Ensure that the gaskets are installed correctly. The gaskets prevent contaminate intrusion.

- Poor terminal connection-Inspect the harness connectors for backed out terminals, improper mating, broken locks, improperly formed or
damaged terminals, and faulty terminal to wire connection. Use a corresponding mating terminal to test for proper tension. Refer to
Diagrams.
- Damaged harness-Inspect the wiring harness for damage. If the harness inspection does not reveal a problem, observe the display on the scan
tool while moving connectors and wiring harnesses related to the sensor. A change in the scan tool display may indicate the location of the
fault. Refer to Diagrams.
- PCM and engine grounds for clean and secure connections

If the DTC is determined to be intermittent, reviewing the Failure Records can be useful in determining when the DTC was last set.

TEST DESCRIPTION
The numbers below refer to the step numbers on the diagnostic table:
2. Verifies that the fault is present.
3. If DTC P0117 can be repeated only by duplicating the Failure Records conditions, refer to the Temperature to Resistance table. See:
Specifications/Electrical Specifications

The table may be used to test the ECT sensor at various temperatures to evaluate the possibility of a shifted sensor that may be shorted above or
below a certain temperature. If this is the case, replace the ECT sensor, If the ECT sensor appears to be OK, the fault is intermittent refer to
Diagnostic Aids.
7. This vehicle is equipped with a PCM which utilizes an Electrically Erasable Programmable Read Only Memory (EEPROM). When the PCM
is being replaced, the new PCM must be programmed. Refer to PCM Replacement/Programming. See: Powertrain Control Module
P0118
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 258
Chevrolet Venture V6-3.4L VIN E 1938

Diagnostic Chart
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 259
Chevrolet Venture V6-3.4L VIN E 1939

Schematic

CIRCUIT DESCRIPTION
The Engine Coolant Temperature (ECT) sensor is a thermistor mounted in the engine coolant stream. The PCM applies a voltage (about 5.0
volts) through a pull up resistor to the ECT signal circuit. When the engine coolant is cold, the sensor (thermistor) resistance is high, therefore
the PCM will measure a high signal voltage. As the engine coolant warms, the sensor resistance becomes less, and the ECT signal voltage
measured at the PCM drops. With a fully warmed up engine, the ECT signal voltage should measure about 1.5 to 2.0 volts.

CONDITIONS FOR RUNNING THE DTC


The engine is running for 15 seconds.

CONDITIONS FOR SETTING THE DTC


- The ECT sensor signal indicates an engine coolant temperature less than -39°C (-37°F).
- Above condition is present for more than 25 seconds.

ACTION TAKEN WHEN THE DTC SETS


- The PCM will illuminate the Malfunction Indicator Lamp (MIL) during the second consecutive trip in which the diagnostic test has been run
and failed.
- The PCM will store conditions which were present when the DTC set as Freeze Frame and Failure Records data.
- If the misfire is determined to be catalyst damaging, the PCM will flash the MIL.

CONDITIONS FOR CLEARING THE MIL/DTC


- The PCM will turn OFF the MIL during the third consecutive trip in which the diagnostic has been run and passed.
- The History DTC will clear after 40 consecutive warm-up cycles have occurred without a malfunction.
- The DTC can be cleared by using a scan tool.

DIAGNOSTIC AIDS
Inspect for the following conditions:

IMPORTANT: Remove any debris from the connector surfaces before servicing a component. Inspect the connector gaskets when diagnosing
or replacing a component. Ensure that the gaskets are installed correctly. The gaskets prevent contaminate intrusion.

- Poor terminal connection-Inspect the harness connectors for backed out terminals, improper mating, broken locks, improperly formed or
damaged terminals, and faulty terminal to wire connection. Use a corresponding mating terminal to test for proper tension. Refer to
Diagrams.
- Damaged harness-Inspect the wiring harness for damage. If the harness inspection does not reveal a problem, observe the display on the scan
tool while moving connectors and wiring harnesses related to the sensor. A change in the scan tool display may indicate the location of the
fault. Refer to Diagrams.
- PCM and engine grounds for clean and secure connections

If the DTC is determined to be intermittent, reviewing the Failure Records can be useful in determining when the DTC was last set.

TEST DESCRIPTION
The numbers below refer to the step numbers on the diagnostic table:
2. Verifies that the fault is present.
3. If DTC P0118 can be repeated only by duplicating the Failure Records conditions. Refer to Temperature vs Resistance table. See:
Specifications/Electrical Specifications

The table may be used to test the ECT sensor at various temperatures to evaluate the possibility of a shifted sensor that may be shorted above or
below a certain temperature. If this is the case, replace the ECT sensor. If the ECT sensor appears to be OK, the fault is intermittent refer to
Diagnostic Aids.
11. This vehicle is equipped with a PCM which utilizes an Electrically Erasable Programmable Read Only Memory (EEPROM). When the PCM
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 260
Chevrolet Venture V6-3.4L VIN E 1940
is being replaced, the new PCM must be programmed. Refer to PCM Replacement/programming. See: Powertrain Control Module

P0121

Diagnostic Chart (Part 1 Of 2)


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 261
Chevrolet Venture V6-3.4L VIN E 1941

Diagnostic Chart (Part 2 Of 2)


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 262
Chevrolet Venture V6-3.4L VIN E 1942

Schematic

CIRCUIT DESCRIPTION
The Throttle Position (TP) sensor circuit provides a voltage signal that changes relative to throttle blade angle. The signal voltage will vary from
below 1.0 volt at closed throttle to above 4.0 volts at Wide Open Throttle (WOT).

When the MAP reading is below 50 kPa the diagnostic tests for a skewed high TP sensor. When the MAP reading is above 70 kPa the
diagnostic tests for a skewed low TP sensor. If the PCM detects an out of range condition, DTC P0121 will be set. The diagnostic will not run
when the MAP is between 50 kPa and 70 kPa.

CONDITIONS FOR RUNNING THE DTC


- Active TP sensor circuit or MAP sensor DTC are not present.
- The engine is running for 2 minutes.
- The ECT sensor temperature above 75°C (167°F).
- The MAP reading is below 50 kPa for a TP sensor skewed high.
- The MAP reading is above 70 kPa for a TP sensor skewed low.
- The MAP steady for 5 seconds or more.

CONDITIONS FOR SETTING THE DTC


- The TP sensor reading is above the predicted value when the MAP is below 50 kPa.
- The TP sensor reading is below the predicted value when the MAP is above 70 kPa.
- The above conditions are present for 10 seconds.

ACTION TAKEN WHEN THE DTC SETS


- The PCM will illuminate the Malfunction Indicator Lamp (MIL) during the second consecutive trip in which the diagnostic test has been run
and failed.
- The PCM will store conditions which were present when the DTC set as Freeze Frame and Failure Records data.
- If the misfire is determined to be catalyst damaging, the PCM will flash the MIL.

CONDITIONS FOR CLEARING THE MIL/DTC


- The PCM will turn OFF the MIL during the third consecutive trip in which the diagnostic has been run and passed.
- The History DTC will clear after 40 consecutive warm-up cycles have occurred without a malfunction.
- The DTC can be cleared by using a scan tool.
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 263
Chevrolet Venture V6-3.4L VIN E 1943

DIAGNOSTIC AIDS
Inspect for a skewed MAP signal or a faulty MAP sensor. A skewed MAP signal may cause the PCM to incorrectly determine that the TP sensor
is out of range. Monitor the scan tool for an unusually low or high MAP reading. This condition can cause DTC P0121 to be set. Refer to MAP
Sensor Circuit Diagnosis. See: Component Tests and General Diagnostics/MAP Sensor Circuit Diagnosis

IMPORTANT: Remove any debris from the connector surfaces before servicing a component. Inspect the connector gaskets when diagnosing
or replacing a component. Ensure that the gaskets are installed correctly. The gaskets prevent contaminate intrusion.

- Poor terminal connection-Inspect the harness connectors for backed out terminals, improper mating, broken locks, improperly formed or
damaged terminals, and faulty terminal to wire connection. Use a corresponding mating terminal to test for proper tension. Refer to
Diagrams.
- Damaged harness-Inspect the wiring harness for damage. If the harness inspection does not reveal a problem, observe the display on the scan
tool while moving connectors and wiring harnesses related to the sensor. A change in the scan tool display may indicate the location of the
fault. Refer to Diagrams.
- PCM and engine grounds for clean and secure connections

If the DTC is determined to be intermittent, reviewing the Failure Records can be useful in determining when the DTC was last set.

TEST DESCRIPTION
The numbers below refer to the step numbers on the diagnostic table:
12. This vehicle is equipped with a PCM which utilizes an Electrically Erasable Programmable Read Only Memory (EEPROM). When the PCM
is being replaced, the new PCM must be programmed.
P0122

Diagnostic Chart (Part 1 Of 2)


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 264
Chevrolet Venture V6-3.4L VIN E 1944

Diagnostic Chart (Part 2 Of 2)

Schematic

CIRCUIT DESCRIPTION
The Throttle Position (TP) sensor circuit provides a voltage signal that changes relative to throttle blade angle. The signal voltage will vary from
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 265
Chevrolet Venture V6-3.4L VIN E 1945
below 1.0 volt at closed throttle to above 4.0 volts at Wide Open Throttle (WOT). The PCM monitors throttle position and compares actual
throttle position from the TP sensor to a predicted TP value calculated from engine speed. If the PCM detects an excessively low TP sensor
signal voltage, DTC P0122 will be set.

CONDITIONS FOR RUNNING THE DTC


The ignition is ON.

CONDITIONS FOR SETTING THE DTC


- TP sensor signal voltage is less than 0.16 volt.
- The above condition is present for longer than 1 second.

ACTION TAKEN WHEN THE DTC SETS


The PCM will illuminate the Malfunction Indicator Lamp (MIL) during the second consecutive trip in which the diagnostic test has been run and
failed.
- The PCM will store conditions which were present when the DTC set as Freeze Frame and Failure Records data.
- If the misfire is determined to be catalyst damaging, the PCM will flash the MIL.

CONDITIONS FOR CLEARING THE MIL/DTC


- The PCM will turn OFF the MIL during the third consecutive trip in which the diagnostic has been run and passed.
- The History DTC will clear after 40 consecutive warm-up cycles have occurred without a malfunction.
- The DTC can be cleared by using a scan tool.

DIAGNOSTIC AIDS
Inspect for the following conditions:

IMPORTANT: Remove any debris from the connector surfaces before servicing a component. Inspect the connector gaskets when diagnosing
or replacing a component. Ensure that the gaskets are installed correctly. The gaskets prevent contaminate intrusion.

- Poor terminal connection-Inspect the harness connectors for backed out terminals, improper mating, broken locks, improperly formed or
damaged terminals, and faulty terminal to wire connection. Use a corresponding mating terminal to test for proper tension. Refer to
Diagrams.
- Damaged harness-Inspect the wiring harness for damage. If the harness inspection does not reveal a problem, observe the display on the scan
tool while moving connectors and wiring harnesses related to the sensor. A change in the scan tool display may indicate the location of the
fault. Refer to Diagrams.
- PCM and engine grounds for clean and secure connections

If the DTC is determined to be intermittent, reviewing the Failure Records can be useful in determining when the DTC was last set.

TEST DESCRIPTION
The numbers below refer to the step numbers on the diagnostic table:
11. This vehicle is equipped with a PCM which utilizes an Electrically Erasable Programmable Read Only Memory (EEPROM). When the PCM
is being replaced, the new PCM must be programmed.

P0123
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 266
Chevrolet Venture V6-3.4L VIN E 1946

Diagnostic Chart (Part 1 Of 2)


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 267
Chevrolet Venture V6-3.4L VIN E 1947

Diagnostic Chart (Part 2 Of 2)


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 268
Chevrolet Venture V6-3.4L VIN E 1948

Schematic

CIRCUIT DESCRIPTION
The Throttle Position (TP) sensor circuit provides a voltage signal that changes relative to throttle blade angle. The signal voltage will vary from
below 1.0 volts at closed throttle to above 4.0 volts at Wide Open Throttle (WOT). DTC P0123 will set when the PCM detects an excessively
high signal voltage on the throttle position sensor signal circuit.

CONDITIONS FOR RUNNING THE DTC


The ignition is ON.

CONDITIONS FOR SETTING THE DTC


- TP sensor signal voltage is more than 4.9 volts.
- The above condition is present for longer than 1 second.

ACTION TAKEN WHEN THE DTC SETS


- The PCM will illuminate the Malfunction Indicator Lamp (MIL) during the second consecutive trip in which the diagnostic test has been run
and failed.
- The PCM will store conditions which were present when the DTC set as Freeze Frame and Failure Records data.
- If the misfire is determined to be catalyst damaging, the PCM will flash the MIL.

CONDITIONS FOR CLEARING THE MIL/DTC


- The PCM will turn OFF the MIL during the third consecutive trip in which the diagnostic has been run and passed.
- The History DTC will clear after 40 consecutive warm-up cycles have occurred without a malfunction.
- The DTC can be cleared by using a scan tool.

DIAGNOSTIC AIDS
- The following components share the TP sensor 5 Volt Reference A circuit:
- The EGR valve
- The MAP sensor
- Test all 5 volt reference A circuits and connected components for a short to voltage:

IMPORTANT: Remove any debris from the connector surfaces before servicing a component. Inspect the connector gaskets when diagnosing
or replacing a component. Ensure that the gaskets are installed correctly. The gaskets prevent contaminate intrusion.
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 269
Chevrolet Venture V6-3.4L VIN E 1949

- Poor terminal connection-Inspect the harness connectors for backed out terminals, improper mating, broken locks, improperly formed or
damaged terminals, and faulty terminal to wire connection. Use a corresponding mating terminal to test for proper tension. Refer to
Diagrams.
- Damaged harness-Inspect the wiring harness for damage. If the harness inspection does not reveal a problem, observe the display on the scan
tool while moving connectors and wiring harnesses related to the sensor. A change in the scan tool display may indicate the location of the
fault. Refer to Diagrams.
- PCM and engine grounds for clean and secure connections

If the DTC is determined to be intermittent, reviewing the Failure Records can be useful in determining when the DTC was last set.

TEST DESCRIPTION
The numbers below refer to the step numbers on the diagnostic table:
9. Tests the components that share the TP sensor 5 Volt Reference A circuit which include the EGR valve, the MAP sensor and the TP sensor.
13. This vehicle is equipped with a PCM which utilizes an Electrically Erasable Programmable Read Only Memory (EEPROM). When the PCM
is being replaced, the new PCM must be programmed.

P0125

Diagnostic Chart

CIRCUIT DESCRIPTION
To provide the best possible combination of driveability, fuel economy, and emission control, a closed loop air/fuel metering system is used.
When the vehicle is first started, the PCM controls fuel delivery in open loop, ignoring the HO2S signals and calculating air/fuel ratio based on
inputs from the ECT, TP, and MAF sensors. The PCM will begin using the HO2S 1 signal for controlling fuel delivery (Closed Loop). when the
following conditions have been met:
- The HO2S output signal is varying, indicating that the sensor is hot enough to operate properly.
- The ECT sensor indicates coolant temperature above 15°C (64°F).
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 270
Chevrolet Venture V6-3.4L VIN E 1950
- Time since start-up is at least 15 seconds for a warm engine or 90 seconds for a cold engine.

The PCM monitors the amount of time for the cooling system to achieve closed loop operating temperature. This diagnostic is broken into three
temperature regions. The diagnostic uses the ECT and IAT sensors to determine which region to operate in. The time to achieve closed loop
temperature is monitored. A time based decision is made depending on the temperature region. The diagnostic will monitor the following
conditions prior to setting the DTC:
- Total airflow must exceed a calibrated amount.
- Engine idle time must be less than a calibrated amount.

CONDITIONS FOR RUNNING THE DTC


- Active IAT or ECT sensor DTCs are not present.
- Minimum air temperature is more than -7°C (19°F).
- Start-up engine coolant temperature is below 50°C (122°F).
- Region 1-Air temperature above 10°C (50°F) and the start up coolant temperature above 10°C (50°F).
- Region 2-Air temperature above -7°C (20°F) and the start up coolant temperature between -7°C (20°F) and 10°C (50°F).
- Region 3-Air temperature above -7°C (20°F) and the start up coolant temperature between -40°C (-40°F) and -7°C (20°F).

CONDITIONS FOR SETTING THE DTC

Region 1
- Engine run time over 127 seconds to achieve Closed Loop temperature of 15°C (64°F).
- Calibrated minimum amount of total airflow has been exceeded.
- Maximum idle time less than 95 seconds.

Region 2
- Engine run time over 280 seconds to achieve closed loop temperature of 15°C (64°F).
- Calibrated minimum amount of total airflow has been exceeded.
- Maximum idle time less than 210 seconds.

Region 3
- Engine run time over 439 seconds to achieve closed loop temperature of 15°C (64°F).
- Calibrated minimum amount of total airflow has been exceeded.
- Maximum idle time less than 329 seconds.

ACTION TAKEN WHEN THE DTC SETS


- The PCM will illuminate the Malfunction Indicator Lamp (MIL) during the second consecutive trip in which the diagnostic test has been run
and failed.
- The PCM will store conditions which were present when the DTC set as Freeze Frame and Failure Records data.
- If the misfire is determined to be catalyst damaging, the PCM will flash the MIL.

CONDITIONS FOR CLEARING THE MIL/DTC


- The PCM will turn OFF the MIL during the third consecutive trip in which the diagnostic has been run and passed.
- The History DTC will clear after 40 consecutive warm-up cycles have occurred without a malfunction.
- The DTC can be cleared by using a scan tool.

DIAGNOSTIC AIDS
DTC P0125 set indicates a skewed ECT sensor. Comparing the engine coolant temperature displayed on a scan tool with actual coolant
temperature measured with a thermometer may isolate this condition. If the displayed engine coolant temperature is not close to the actual
coolant temperature, replace the ECT sensor.

Inspect for the following conditions:

IMPORTANT: Remove any debris from the connector surfaces before servicing a component. Inspect the connector gaskets when diagnosing
or replacing a component. Ensure that the gaskets are installed correctly. The gaskets prevent contaminate intrusion.

- Poor terminal connection-Inspect the harness connectors for backed out terminals, improper mating, broken locks, improperly formed or
damaged terminals, and faulty terminal to wire connection. Use a corresponding mating terminal to test for proper tension. Refer to
Diagrams.
- Damaged harness-Inspect the wiring harness for damage. If the harness inspection does not reveal a problem, observe the display on the scan
tool while moving connectors and wiring harnesses related to the sensor. A change in the scan tool display may indicate the location of the
fault. Refer to Diagrams.
- PCM and engine grounds for clean and secure connections

If the DTC is determined to be intermittent, reviewing the Failure Records can be useful in determining when the DTC was last set.

TEST DESCRIPTION
The numbers below refer to the step numbers on the diagnostic table:
7. This vehicle is equipped with a PCM which utilizes an Electrically Erasable Programmable Read Only Memory (EEPROM). When the PCM
is being replaced, the new PCM must be programmed.
P0131
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 271
Chevrolet Venture V6-3.4L VIN E 1951

Diagnostic Chart

Schematic

CIRCUIT DESCRIPTION
The PCM supplies a bias voltage of about 450 mV between the HO2S signal and low circuits. When measured with a 10 megaohm DMM, this
may display as low as 350 mV. The oxygen sensor varies the voltage within a range of about 1000 mV when the exhaust is rich, down through
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 272
Chevrolet Venture V6-3.4L VIN E 1952
about 100 mV when exhaust is lean. The PCM constantly monitors the HO2S signal during closed loop operation and compensates for a rich or
lean condition by decreasing or increasing injector pulse width as necessary. If the HO2S 1 voltage remains excessively low for an extended
period of time, DTC P0131 will be set.

CONDITIONS FOR RUNNING THE DTC


- Active TP, MAP, IAT, ECT, MAF sensor, fuel injector circuit, EVAP, AIR DTCs are not present.
- Closed loop commanded air/fuel ratio is between 13 and 16.5.
- Throttle angle is between 3 percent and 40 percent.
- AIR pump commanded OFF.
- Ignition voltage is between 9.0 and 18.0 volts.

CONDITIONS FOR SETTING THE DTC


HO2S 1 signal voltage remains below 175 mV during normal closed loop operation for more than 50 seconds.
OR
HO2S 1 signal voltage remains below 600 mV during power enrichment mode fuel control operation for more than 10 seconds.

ACTION TAKEN WHEN THE DTC SETS


- The PCM will illuminate the Malfunction Indicator Lamp (MIL) during the second consecutive trip in which the diagnostic test has been run
and failed.
- The PCM will store conditions which were present when the DTC set as Freeze Frame and Failure Records data.
- If the misfire is determined to be catalyst damaging, the PCM will flash the MIL.

CONDITIONS FOR CLEARING THE MIL/DTC


- The PCM will turn OFF the MIL during the third consecutive trip in which the diagnostic has been run and passed.
- The History DTC will clear after 40 consecutive warm-up cycles have occurred without a malfunction.
- The DTC can be cleared by using a scan tool.

DIAGNOSTIC AIDS
Inspect for the following conditions:
- Heated oxygen sensor wiring-The sensor pigtail may be routed incorrectly and contacting the exhaust system.
- Poor PCM to engine block grounds-Refer to Ground Distribution Schematics in Diagrams.
- Fuel pressure-The system will go lean if pressure is too low. The PCM can compensate for some decrease. However, if fuel pressure is too
low, a DTC P0131 may be set. Refer to Fuel System Diagnosis. See: Fuel Delivery and Air Induction/Testing and Inspection/Component
Tests and General Diagnostics/Fuel System Diagnosis
- Lean injectors-Perform Injector Balance Test. Refer to Fuel Injector Balance Test. See: Component Tests and General Diagnostics/Fuel
Injector Balance Test
- Vacuum leaks-Inspect for disconnected or damaged vacuum hoses and for vacuum leaks at the intake manifold, throttle body, EGR system,
and crankcase ventilation system. Refer to Visual/Physical Check in Symptoms. See: Initial Inspection and Diagnostic Overview
- Exhaust leaks-An exhaust leak may cause outside air to be pulled into the exhaust gas stream past the HO2S, causing the system to appear
lean. Inspect for exhaust leaks that may cause a false lean condition to be indicated.
- MAF sensor-Disconnect the MAF sensor and see if the lean condition is corrected. If so, replace MAF sensor.
- Fuel contamination-Water, even in small amounts, can be delivered to the fuel injectors. The water can cause a lean exhaust to be indicated.
Excessive alcohol in the fuel can also cause this condition. Refer to Alcohol/Contaminants-in-Fuel Diagnosis. See: Component Tests and
General Diagnostics/Fuel Quality Diagnosis

IMPORTANT: Remove any debris from the connector surfaces before servicing a component. Inspect the connector gaskets when diagnosing
or replacing a component. Ensure that the gaskets are installed correctly. The gaskets prevent contaminate intrusion.

- Poor terminal connection-Inspect the harness connectors for backed out terminals, improper mating, broken locks, improperly formed or
damaged terminals, and faulty terminal to wire connection. Use a corresponding mating terminal to test for proper tension. Refer to
Diagrams.
- Damaged harness-Inspect the wiring harness for damage. If the harness inspection does not reveal a problem, observe the display on the scan
tool while moving connectors and wiring harnesses related to the sensor. A change in the scan tool display may indicate the location of the
fault. Refer to Diagrams.
- PCM and engine grounds for clean and secure connections

If the DTC is determined to be intermittent, reviewing the Failure Records can be useful in determining when the DTC was last set.

TEST DESCRIPTION
The numbers below refer to step numbers on the diagnostic table:
3. This DTC failing during power enrichment operation (TP angle above 60 percent) may indicate a condition described in Diagnostic Aids. If
this DTC test passes while the Failure Records conditions are being duplicated, an intermittent condition is indicated. Review the Failure
Records vehicle mileage since the diagnostic test last failed. This may help determine how often the condition that caused the DTC to be set
occurs.
6. This vehicle is equipped with a PCM which utilizes an Electrically Erasable Programmable Read Only Memory (EEPROM). When the PCM
is replaced, the new PCM must be programmed.

P0132
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 273
Chevrolet Venture V6-3.4L VIN E 1953

Diagnostic Chart

Schematic
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 274
Chevrolet Venture V6-3.4L VIN E 1954

CIRCUIT DESCRIPTION
The PCM supplies a bias voltage of about 450 mV between the HO2S signal and low circuits. When measured with a 10 megaohm DMM, this
may display as low as 320 mV. The oxygen sensor varies the voltage within a range of about 1000 mV when the exhaust is rich, down through
about 10 mV when exhaust is lean. The PCM constantly monitors the HO2S signal during closed loop operation and compensates for a rich or
lean condition by decreasing or increasing injector pulse width as necessary. If the HO2S 1 voltage remains excessively high for an extended
period of time, DTC P0132 will be set.

CONDITIONS FOR RUNNING THE DTC


- AIR pump commanded OFF.
- Active TP, MAP, MAF, ECT, IAT Sensor, fuel injector circuit, EVAP, EGR, or AIR DTCs are not present.
- System voltage is more than 9.0 volts.
- System voltage is between 13 and 16.5 volts.
- Closed loop commanded air/fuel ratio is between 14.5 and 14.8.
- Throttle angle is between 3 percent and 40 percent.

CONDITIONS FOR SETTING THE DTC


- HO2S 1 signal voltage remains above 977 mV for longer than 50 seconds during normal closed loop operation
OR
- HO2S 1 signal voltage remains above 200 mV for longer than 10 seconds during deceleration fuel mode operation.

ACTION TAKEN WHEN THE DTC SETS


- The PCM will illuminate the Malfunction Indicator Lamp (MIL) during the second consecutive trip in which the diagnostic test has been run
and failed.
- The PCM will store conditions which were present when the DTC set as Freeze Frame and Failure Records data.
- If the misfire is determined to be catalyst damaging, the PCM will flash the MIL.

CONDITIONS FOR CLEARING THE MIL/DTC


- The PCM will turn OFF the MIL during the third consecutive trip in which the diagnostic has been run and passed.
- The History DTC will clear after 40 consecutive warm-up cycles have occurred without a malfunction.
- The DTC can be cleared by using a scan tool.

DIAGNOSTIC AIDS
- Verify the fuel pressure. The system will go rich if pressure is too high. The PCM can compensate for some increase. However, if fuel
pressure is too high. Refer to Fuel System Pressure Test. See: Fuel Delivery and Air Induction/Fuel Pressure/Testing and Inspection/Fuel
System Pressure Test
- Perform Injector Balance Test. Refer to Fuel Injector Balance Test. See: Component Tests and General Diagnostics/Fuel Injector Balance
Test
- Inspect the EVAP Canister for fuel saturation. If full of fuel, check canister control and hoses.
- Disconnect the MAF sensor and see if rich condition is corrected. If so, replace the MAF sensor.
- Inspect for a leaking fuel pressure regulator diaphragm by checking vacuum line to regulator for the presence of fuel.
- Inspect for an intermittent TP sensor output which will cause the system to go rich due to a false indication of the engine accelerating.
- Inspect for a shorted Heated Oxygen Sensor (HO2S). If the HO2S is internally shorted the HO2S voltage displayed on the scan tool will be
over 1.0 volt. Disconnect the affected HO2S and jumper the HO2S low circuit to ground with the key ON, engine OFF. If the displayed
HO2S voltage changes from over 1000 mV to around 450 mV, replace the HO2S. Silicon contamination of the HO2S can also cause a high
HO2S voltage to be indicated. This condition is indicated by a powdery white deposit on the portion of the HO2S exposed to the exhaust
stream. If contamination is noticed, replace the affected HO2S.
- Inspect for an open HO2S signal or a low circuit which may cause the DTC to set during deceleration fuel mode. Operate the vehicle while
monitoring the HO2S voltage with a scan tool. If the HO2S voltage is limited within a range between 300 mV to 600 mV, check the HO2S
signal and low circuit wiring and associated terminal connections. If the wiring and connections are OK, replace the HO2S.
- Inspect for a faulty HO2S. An HO2S which is faulty and not allowing a full voltage swing between the rich and lean thresholds may set this
DTC. Replace the HO2S.

IMPORTANT: Remove any debris from the connector surfaces before servicing a component. Inspect the connector gaskets when diagnosing
or replacing a component. Ensure that the gaskets are installed correctly. The gaskets prevent contaminate intrusion.

- Poor terminal connection-Inspect the harness connectors for backed out terminals, improper mating, broken locks, improperly formed or
damaged terminals, and faulty terminal to wire connection. Use a corresponding mating terminal to test for proper tension. Refer to
Diagrams.
- Damaged harness-Inspect the wiring harness for damage. If the harness inspection does not reveal a problem, observe the display on the scan
tool while moving connectors and wiring harnesses related to the sensor. A change in the scan tool display may indicate the location of the
fault. Refer to Diagrams.
- PCM and engine grounds for clean and secure connections

If the DTC is determined to be intermittent, reviewing the Failure Records can be useful in determining when the DTC was last set.

TEST DESCRIPTION
The numbers below refer to step numbers on the diagnostic table:
3. This DTC failing during deceleration fuel mode operation (vehicle speed above 25 mph, TP angle below 3 percent) may indicate a condition
described in Diagnostic Aids. If this DTC test passes while the Fail Records conditions are being duplicated, an intermittent condition is
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 275
Chevrolet Venture V6-3.4L VIN E 1955
indicated. Review the Fail Records vehicle mileage since the diagnostic test last failed. This may help determine how often the condition that
caused the DTC to be set occurs.
7. This vehicle is equipped with a PCM which utilizes an Electrically Erasable Programmable Read Only Memory (EEPROM). When the PCM
is replaced, the new PCM must be programmed.

P0133

Diagnostic Chart (Part 1 Of 2)


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 276
Chevrolet Venture V6-3.4L VIN E 1956

Diagnostic Chart (Part 2 Of 2)


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 277
Chevrolet Venture V6-3.4L VIN E 1957

Schematic

CIRCUIT DESCRIPTION
The PCM continuously monitors the Heated Oxygen Sensor (HO2S) activity for 100 seconds. During the monitoring period the PCM counts the
number of times that a rich to lean and lean to rich response is indicated and adds the amount of time taken to complete all transitions. With this
information, an average time for each transition can be determined. If the average response time is too slow, a DTC P0133 will be set.

A lean to rich transition is indicated when the HO2S voltage changes from less than 300 mV to more than 600 mV. A rich to lean transition is
indicated when the HO2S voltage changes from more than 600 mV to less than 300 mV. An HO2S that responds too slowly is likely to be faulty
and should be replaced.

CONDITIONS FOR RUNNING THE DTC


- Active TP, MAP, MAF, IAT, ECT, or AIR, misfire, fuel injector circuit, or EVAP DTCs are not present
- Engine has been running in Closed Loop for at least 1 minute.
- MAF between 10 grams per second and 30 grams per second.
- System voltage between 9.0 and 18.0 volts.
- Engine speed is between 1000 RPM and 3000 RPM.
- ECT is more than 50°C (122°F).
- Vehicle not in Park or Neutral
- AIR pump commanded OFF.

CONDITIONS FOR SETTING THE DTC


- HO2S 1 lean to rich average transition response time was longer than 94 milliseconds.
- HO2S 1 rich to lean average transition response time was longer than 105 milliseconds.

ACTION TAKEN WHEN THE DTC SETS


- The PCM will illuminate the Malfunction Indicator Lamp (MIL) during the second consecutive trip in which the diagnostic test has been run
and failed.
- The PCM will store conditions which were present when the DTC set as Freeze Frame and Failure Records data.
- If the misfire is determined to be catalyst damaging, the PCM will flash the MIL.

CONDITIONS FOR CLEARING THE MIL/DTC


- The PCM will turn OFF the MIL during the third consecutive trip in which the diagnostic has been run and passed.
- The History DTC will clear after 40 consecutive warm-up cycles have occurred without a malfunction.
- The DTC can be cleared by using a scan tool.

DIAGNOSTIC AIDS
Inspect for the following conditions:

IMPORTANT: Remove any debris from the connector surfaces before servicing a component. Inspect the connector gaskets when diagnosing
or replacing a component. Ensure that the gaskets are installed correctly. The gaskets prevent contaminate intrusion.

- Poor terminal connection-Inspect the harness connectors for backed out terminals, improper mating, broken locks, improperly formed or
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 278
Chevrolet Venture V6-3.4L VIN E 1958
damaged terminals, and faulty terminal to wire connection. Use a corresponding mating terminal to test for proper tension. Refer to
Diagrams.
- Damaged harness-Inspect the wiring harness for damage. If the harness inspection does not reveal a problem, observe the display on the scan
tool while moving connectors and wiring harnesses related to the sensor. A change in the scan tool display may indicate the location of the
fault. Refer to Diagrams.
- PCM and engine grounds for clean and secure connections

If the DTC is determined to be intermittent, reviewing the Failure Records can be useful in determining when the DTC was last set.

TEST DESCRIPTION
The numbers below refer to the step numbers on the diagnostic table:
2. When the system is operating correctly the HO2S voltage should toggle above and below the specified values.
5. If the low circuit is shorted to ground the HO2S voltage will be less than 400 mV when the signal circuit is jumped to ground.
6. The specified value is what is measured on a correctly operating system.
7. The specified value is what is measured on a correctly operating system.
14. This vehicle is equipped with a PCM which utilizes an Electrically Erasable Programmable Read Only Memory (EEPROM). When the PCM
is replaced, the new PCM must be programmed.

P0134

Diagnostic Chart (Part 1 Of 2)


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 279
Chevrolet Venture V6-3.4L VIN E 1959

Diagnostic Chart (Part 2 Of 2)


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 280
Chevrolet Venture V6-3.4L VIN E 1960

Schematic

CIRCUIT DESCRIPTION
The PCM supplies a bias voltage of about 450 mV between the HO2S signal and low circuits. When measured with a 10 megaohm DMM, this
may display as low as 320 mV. The oxygen sensor varies the voltage within a range of about 1000 mV when the exhaust is rich, down through
about 10 mV when exhaust is lean. The PCM constantly monitors the HO2S signal during closed loop operation and compensates for a rich or
lean condition by decreasing or increasing injector pulse width as necessary. If the HO2S 1 voltage remains at or near the 450 mV bias for an
extended period of time, DTC P0134 will be set, indicating an open sensor signal or sensor low circuit.

CONDITIONS FOR RUNNING THE DTC


- Active TP, MAP, MAF, ECT, IAT sensor, fuel injector circuit, EVAP, or AIR DTCs are not present.
- System voltage between 9.0 and 18.0 volts.
- Engine run time longer than 200 seconds.
- ECT is more than 50°C (122°F).

CONDITIONS FOR SETTING THE DTC


HO2S 1 signal voltage remains between 408 mV and 512 mV for longer than 29 seconds.

ACTION TAKEN WHEN THE DTC SETS


- The PCM will illuminate the Malfunction Indicator Lamp (MIL) during the second consecutive trip in which the diagnostic test has been run
and failed.
- The PCM will store conditions which were present when the DTC set as Freeze Frame and Failure Records data.
- If the misfire is determined to be catalyst damaging, the PCM will flash the MIL.

CONDITIONS FOR CLEARING THE MIL/DTC


- The PCM will turn OFF the MIL during the third consecutive trip in which the diagnostic has been run and passed.
- The History DTC will clear after 40 consecutive warm-up cycles have occurred without a malfunction.
- The DTC can be cleared by using a scan tool.

DIAGNOSTIC AIDS
Inspect for the following conditions:
- A faulty HO2S heater or heater circuit.-With the ignition ON, engine OFF, the HO2S voltage displayed on a scan tool should gradually drop
to below 250 mV or rise to above 600 mV. If not, disconnect the HO2S and connect a test lamp between the HO2S ignition feed and heater
ground circuits. If the test lamp does not light, repair the open ignition feed or sensor ground circuit as necessary. If the test lamp illuminates
and the HO2S signal and low circuits are OK, replace the HO2S.
- Intermittents- With the ignition ON, monitor the HO2S signal voltage while moving the wiring harness and related connectors. If the fault is
induced, the HO2S signal voltage will change. This may help isolate the location of the malfunction.

IMPORTANT: Remove any debris from the connector surfaces before servicing a component. Inspect the connector gaskets when diagnosing
or replacing a component. Ensure that the gaskets are installed correctly. The gaskets prevent contaminate intrusion.

- Poor terminal connection-Inspect the harness connectors for backed out terminals, improper mating, broken locks, improperly formed or
damaged terminals, and faulty terminal to wire connection. Use a corresponding mating terminal to test for proper tension. Refer to
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 281
Chevrolet Venture V6-3.4L VIN E 1961
Diagrams.
- Damaged harness-Inspect the wiring harness for damage. If the harness inspection does not reveal a problem, observe the display on the scan
tool while moving connectors and wiring harnesses related to the sensor. A change in the scan tool display may indicate the location of the
fault. Refer to Diagrams.
- PCM and engine grounds for clean and secure connections

If the DTC is determined to be intermittent, reviewing the Failure Records can be useful in determining when the DTC was last set.

TEST DESCRIPTION
The numbers below refer to the step numbers on the diagnostic table:
2. When the system is operating correctly the HO2S voltage should toggle above and below the specified values.
5. If the low circuit is shorted to ground the HO2S voltage will be less than 400 mV when the signal circuit is jumped to ground.
6. The specified value is what is measured on a correctly operating system.
7. The specified value is what is measured on a correctly operating system.
14. This vehicle is equipped with a PCM which utilizes an Electrically Erasable Programmable Read Only Memory (EEPROM). When the PCM
is replaced, the new PCM must be programmed.
P0135

Diagnostic Chart (Part 1 Of 2)


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 282
Chevrolet Venture V6-3.4L VIN E 1962

Diagnostic Chart (Part 2 Of 2)


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 283
Chevrolet Venture V6-3.4L VIN E 1963

Schematic

CIRCUIT DESCRIPTION
Heated oxygen sensors are used to minimize the amount of time required for closed loop fuel control operation and to allow accurate catalyst
monitoring. The oxygen sensor heater greatly decreases the amount of time required for fuel control sensor HO2S 1 to become active. The
oxygen sensor heater is required by catalyst monitor sensor HO2S 2 to maintain a sufficiently high temperature. This allows accurate exhaust
oxygen content readings further from the engine.

The PCM will run the heater test only after a cold start, determined by engine coolant and intake air temperature at the time of start-up, and only
once during an ignition cycle. When the engine is started the PCM will monitor the HO2S voltage. When the HO2S voltage indicates a
sufficiently active sensor, the PCM looks at how much time has elapsed since start-up. If the PCM determines that too much time was required
for the HO2S 1 to become active, a DTC P0135 will set. The time required for the HO2S to reach operating temperature is based on the ECT at
start up and the average MAF since start-up. A higher average airflow or higher start-up ECT = shorter time to HO2S activity.

CONDITIONS FOR RUNNING THE DTC


- Active TP, MAP, MAF, ECT, IAT, fuel injector circuit, EVAP, or AIR DTCs are not present.
- Intake air temperature (IAT) is less than 35°C (95°F) at start up.
- Engine coolant temperature (ECT) is less than 35°C (95°F) at start up.
- IAT and ECT are within 6°C (42°F) of each other at start up.
- Battery voltage above 9.0 volts and below 18.0 volts.
- AIR pump is commanded OFF.

CONDITIONS FOR SETTING THE DTC


HO2S 1 voltage remains within 150 mV of the bias voltage, about 450 mV, for a longer amount of time than normally required. The amount of
time varies depending on engine coolant temperature at start-up and average air flow since start-up, but will not exceed 2.5 minutes.

ACTION TAKEN WHEN THE DTC SETS


- The PCM will illuminate the malfunction indicator lamp (MIL) during the second consecutive trip in which the diagnostic test has been run
and failed.
- The PCM will store conditions which were present when the DTC set as Freeze Frame and Failure Records data.
- If the misfire is determined to be catalyst damaging, the PCM will flash the MIL.

CONDITIONS FOR CLEARING THE MIL/DTC


- The PCM will turn OFF the MIL during the third consecutive trip in which the diagnostic has been run and passed.
- The History DTC will clear after 40 consecutive warm-up cycles have occurred without a malfunction.
- The DTC can be cleared by using a scan tool.

DIAGNOSTIC AIDS
Inspect for the following conditions:

IMPORTANT: Remove any debris from the connector surfaces before servicing a component. Inspect the connector gaskets when diagnosing
or replacing a component. Ensure that the gaskets are installed correctly. The gaskets prevent contaminate intrusion.
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 284
Chevrolet Venture V6-3.4L VIN E 1964

- Poor terminal connection-Inspect the harness connectors for backed out terminals, improper mating, broken locks, improperly formed or
damaged terminals, and faulty terminal to wire connection. Use a corresponding mating terminal to test for proper tension. Refer to
Diagrams.
- Damaged harness-Inspect the wiring harness for damage. If the harness inspection does not reveal a problem, observe the display on the scan
tool while moving connectors and wiring harnesses related to the sensor. A change in the scan tool display may indicate the location of the
fault. Refer to Diagrams.
- PCM and engine grounds for clean and secure connections

If the DTC is determined to be intermittent, reviewing the Failure Records can be useful in determining when the DTC was last set.

TEST DESCRIPTION
The numbers below refer to the step numbers on the diagnostic table:
2. The HO2S should be allowed to cool before performing this test. If the HO2S heater is functioning, the signal voltage will gradually increase
or decrease as the sensor element warms. If the heater is not functioning, the HO2S signal will remain near the 450 mV bias voltage.
4. This step ensures that the ignition feed circuit to the HO2S is not open or shorted. The test lamp should be connected to a good ground, in
case the HO2S low or HO2S heater ground circuit is faulty.
5. This step tests the HO2S heater ground circuit.
6. This step inspects for an open or shorted HO2S heater element. The heater element resistance will vary according to HO2S temperature (a hot
HO2S heater element will measure a much higher resistance than a HO2S heater element at room temperature). It is important to allow the
HO2S to cool before measuring HO2S heater element resistance.

P0137
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 285
Chevrolet Venture V6-3.4L VIN E 1965

Diagnostic Chart
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 286
Chevrolet Venture V6-3.4L VIN E 1966

Schematic

CIRCUIT DESCRIPTION
To control emissions of Hydrocarbons (HC), Carbon Monoxide (CO), and Oxides of Nitrogen (NOx), a three way catalytic converter is used.
The catalyst within the converter promotes a chemical reaction which oxidizes the HC and CO present in the exhaust gas, converting them into
harmless water vapor and carbon dioxide. The catalyst also reduces NOx, converting it to nitrogen. The PCM has the ability to monitor this
process using the HO2S 1 and the HO2S 2 heated oxygen sensors. The HO2S 1 sensor produces an output signal which indicates the amount of
oxygen present in the exhaust gas entering the three-way catalytic converter. The HO2S 2 sensor produces an output signal which indicates the
oxygen storage capacity of the catalyst this in turn indicates the catalysts ability to convert exhaust gases efficiently. If the catalyst is operating
efficiently, the HO2S 1 signal will be far more active than that produced by the HO2S 2 sensor. If the HO2S 2 signal voltage remains excessively
low for an extended period of time, DTC P0137 will be set.

CONDITIONS FOR RUNNING THE DTC


- No active TP, MAP, MAF, IAT, ECT, CKP Sensor, misfire, fuel injector circuit, EVAP, Fuel trim, or EGR DTCs present.
- Engine coolant temperature above 65°C (149°F).
- Closed loop commanded air/fuel ratio is between 14.5-14.8.
- Throttle angle is between 3-40 percent.

CONDITIONS FOR SETTING THE DTC


HO2S 2 signal voltage remains below 10 mV during normal closed loop operation.
OR
- HO2S 2 signal voltage remains below 600 mV during power enrichment mode fuel control operation.
- Either condition for up to 5 seconds.

ACTION TAKEN WHEN THE DTC SETS


- The PCM will illuminate the malfunction indicator lamp (MIL) during the second consecutive trip in which the diagnostic test has been run
and failed.
- The PCM will store conditions which were present when the DTC set as Freeze Frame and Failure Records data.
- If the misfire is determined to be catalyst damaging, the PCM will flash the MIL.

CONDITIONS FOR CLEARING THE MIL/DTC


The PCM will turn OFF the MIL during the third consecutive trip in which the diagnostic has been run and passed.
- The History DTC will clear after 40 consecutive warm-up cycles have occurred without a malfunction.
- The DTC can be cleared by using a scan tool.

DIAGNOSTIC AIDS
Inspect for the following conditions:
- Heated oxygen sensor wiring. The sensor pigtail may be mispositioned and contacting the exhaust system.. Refer to Wiring Repairs in
Diagrams.
- Faulty PCM to engine grounds. Refer to Power and Grounding Component Views in Diagrams.
- Fuel pressure - A condition which causes a lean exhaust can cause DTC P0137 to set. The system will go lean if pressure is too low. The
PCM can compensate for some decrease. However, if fuel pressure is too low, a DTC P0137 may be set. Refer to Fuel System Diagnosis.
See: Fuel Delivery and Air Induction/Testing and Inspection/Component Tests and General Diagnostics/Fuel System Diagnosis
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 287
Chevrolet Venture V6-3.4L VIN E 1967
- Lean injectors - Perform the Injector Balance Test. Refer to Fuel Injector Balance Test. See: Component Tests and General Diagnostics/Fuel
Injector Balance Test
- Vacuum leaks - Inspect for disconnected or damaged vacuum hoses and for vacuum leaks at the intake manifold, throttle body, EGR system,
and Crankcase Ventilation System. Refer to Visual/Physical Inspection in Symptoms. See: Initial Inspection and Diagnostic Overview
- Exhaust leaks - An exhaust leak may cause outside air to be pulled into the exhaust gas stream past the HO2S, causing the DTC P0137 to set.
Inspect for exhaust leaks near the HO2S 2 sensor.
- Fuel contamination - Water, even in small amounts, can be delivered to the fuel injectors. The water can cause a lean exhaust to be indicated.
Excessive alcohol in the fuel can also cause this condition. Refer to Alcohol/Contaminants-in-Fuel Diagnosis. See: Component Tests and
General Diagnostics/Fuel Quality Diagnosis

IMPORTANT: Remove any debris from the connector surfaces before servicing a component. Inspect the connector gaskets when diagnosing
or replacing a component. Ensure that the gaskets are installed correctly. The gaskets prevent contaminate intrusion.

- Poor terminal connection-Inspect the harness connectors for backed out terminals, improper mating, broken locks, improperly formed or
damaged terminals, and faulty terminal to wire connection. Use a corresponding mating terminal to test for proper tension. Refer to
Diagrams.
- Damaged harness-Inspect the wiring harness for damage. If the harness inspection does not reveal a problem, observe the display on the scan
tool while moving connectors and wiring harnesses related to the sensor. A change in the scan tool display may indicate the location of the
fault. Refer to Diagrams.
- PCM and engine grounds for clean and secure connections

If the DTC is determined to be intermittent, reviewing the Failure Records can be useful in determining when the DTC was last set.

TEST DESCRIPTION
The numbers below refer to the step numbers on the diagnostic table:
3. DTC P0137 being set in power enrichment mode conditions may indicate a condition described in the Diagnostic Aids above. If the DTC
P0137 test passes while the Failure Records conditions are being duplicated, an intermittent condition is indicated. Reviewing the Fail
Records vehicle mileage since the diagnostic test last failed may help determine how often the condition that caused the DTC to be set
occurs. This may assist in diagnosing the condition.
7. This vehicle is equipped with a PCM which utilizes an electrically erasable programmable read only memory (EEPROM). When the PCM is
being replaced, the new PCM must be programmed.

P0138
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 288
Chevrolet Venture V6-3.4L VIN E 1968

Diagnostic Chart
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 289
Chevrolet Venture V6-3.4L VIN E 1969

Schematic

CIRCUIT DESCRIPTION
To control emissions of Hydrocarbons (HC), Carbon Monoxide (CO), and Oxides of Nitrogen (NOx), a three way catalytic converter is used.
The catalyst within the converter promotes a chemical reaction which oxidizes the HC and CO present in the exhaust gas, converting them into
harmless water vapor and carbon dioxide. The catalyst also reduces NOx, converting NOx to nitrogen. The PCM has the ability to monitor this
process using the HO2S 1 and the HO2S 2 heated oxygen sensors. The HO2S 1 sensor produces an output signal which indicates the amount of
oxygen present in the exhaust gas entering the three way catalytic converter. The HO2S 2 sensor produces an output signal which indicates the
oxygen storage capacity of the catalyst this in turn indicates the catalysts ability to convert exhaust gases efficiently. If the catalyst is operating
efficiently, the HO2S 1 signal will be far more active than that produced by the HO2S 2 sensor. If the HO2S 2 signal voltage remains excessively
high for an extended period of time, DTC P0138 will be set.

CONDITIONS FOR RUNNING THE DTC


- Active TP, MAP, MAF, ECT, IAT sensor, fuel injector circuit, or EVAP DTCs are not present.
- AIR pump is commanded OFF.
- ECT is above 65°C (149°F).
- Throttle angle is between 3 percent and 40 percent.
- Closed loop commanded air/fuel ratio is between 13 and 16.5.
- System voltage is between 9 and 18 volts.

CONDITIONS FOR SETTING THE DTC


- HO2S 2 signal voltage remains above 999 mV during normal closed loop operation for more than 5 minutes.
- HO2S 2 signal voltage remains above 200 mV during deceleration fuel mode operation for more than 100 seconds.

ACTION TAKEN WHEN THE DTC SETS


- The PCM will illuminate the Malfunction Indicator Lamp (MIL) during the second consecutive trip in which the diagnostic test has been run
and failed.
- The PCM will store conditions which were present when the DTC set as Freeze Frame and Failure Records data.
- If the misfire is determined to be catalyst damaging, the PCM will flash the MIL.

CONDITIONS FOR CLEARING THE MIL/DTC


- The PCM will turn OFF the MIL during the third consecutive trip in which the diagnostic has been run and passed.
- The History DTC will clear after 40 consecutive warm-up cycles have occurred without a malfunction.
- The DTC can be cleared by using a scan tool.

DIAGNOSTIC AIDS
Inspect for the following conditions:
- Fuel pressure-An excessively rich fuel mixture can cause a DTC P0138 to be set. Refer to Fuel System Diagnosis. See: Fuel Delivery and
Air Induction/Testing and Inspection/Component Tests and General Diagnostics/Fuel System Diagnosis
- Rich injectors-Refer to Fuel Injector Balance Test. See: Component Tests and General Diagnostics/Fuel Injector Balance Test
- Leaking injector-Refer to Fuel System Diagnosis. See: Fuel Delivery and Air Induction/Testing and Inspection/Component Tests and
General Diagnostics/Fuel System Diagnosis
- Evaporative Emissions (EVAP) canister purge- Inspect for fuel saturation. If full of fuel, inspect the canister control and hoses.
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 290
Chevrolet Venture V6-3.4L VIN E 1970
- MAF sensor-Disconnect the MAF sensor and see if rich condition is corrected. If so, replace MAF sensor.
- Inspect for a leaking fuel pressure regulator diaphragm by checking vacuum line to regulator for the presence of fuel.
- TP sensor-An intermittent TP sensor output will cause the system to go rich, due to a false indication of the engine accelerating.
- Shorted Heated Oxygen Sensor (HO2S)-If the HO2S is internally shorted the HO2S voltage displayed on the scan tool will be over 1 volt.
Try disconnecting the affected HO2S and jumper the HO2S low circuit to ground with the key ON, engine OFF. If the displayed HO2S
voltage changes from over 1000 mV to around 450 mV, replace the HO2S. Silicon contamination of the HO2S can also cause a high HO2S
voltage to be indicated. This condition is indicated by a powdery white deposit on the portion of the HO2S exposed to the exhaust stream. If
contamination is evident, replace the affected HO2S.
- Open HO2S signal or low circuit, or faulty HO2S.-A poor connection or open in the HO2S signal or low circuit can cause the DTC to set
during deceleration fuel mode. An HO2S which is faulty and not allowing a full voltage swing between the rich and lean thresholds can also
cause this condition. Operate the vehicle while monitoring the HO2S voltage with a scan tool. If the HO2S voltage is limited within a range
between 300 mV to 600 mV, check the HO2S signal and low circuit wiring and associated terminal connections. If the wiring and
connections are OK, replace the HO2S.

IMPORTANT: Remove any debris from the connector surfaces before servicing a component. Inspect the connector gaskets when diagnosing
or replacing a component. Ensure that the gaskets are installed correctly. The gaskets prevent contaminate intrusion.

- Poor terminal connection-Inspect the harness connectors for backed out terminals, improper mating, broken locks, improperly formed or
damaged terminals, and faulty terminal to wire connection. Use a corresponding mating terminal to test for proper tension. Refer to
Diagrams.
- Damaged harness-Inspect the wiring harness for damage. If the harness inspection does not reveal a problem, observe the display on the scan
tool while moving connectors and wiring harnesses related to the sensor. A change in the scan tool display may indicate the location of the
fault. Refer to Diagrams.
- PCM and engine grounds for clean and secure connections

If the DTC is determined to be intermittent, reviewing the Failure Records can be useful in determining when the DTC was last set.

TEST DESCRIPTION
The number below refers to the step number on the diagnostic table:
3. DTC P0138 being set during deceleration fuel mode operation may indicate a condition described in the Diagnostic Aids above. If the DTC
P0138 test passes while the Failure Records conditions are being duplicated, an intermittent condition is indicated. Reviewing the Failure
Records vehicle mileage since the diagnostic test last failed may help determine how often the condition that caused the DTC to be set
occurs. This may assist in diagnosing the condition.
7. This vehicle is equipped with a PCM which utilizes an electrically erasable programmable read only memory (EEPROM). When the PCM is
being replaced, the new PCM must be programmed.

P0140

Diagnostic Chart (Part 1 Of 2)


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 291
Chevrolet Venture V6-3.4L VIN E 1971

Diagnostic Chart (Part 2 Of 2)


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 292
Chevrolet Venture V6-3.4L VIN E 1972

Schematic

CIRCUIT DESCRIPTION
To control emissions of Hydrocarbons (HC), Carbon Monoxide (CO), and Oxides of Nitrogen (NOx), a three way catalytic converter is used.
The catalyst within the converter promotes a chemical reaction which oxidizes the HC and CO present in the exhaust gas, converting them into
harmless water vapor and carbon dioxide. The catalyst also reduces NOx, converting NOx to nitrogen. The PCM has the ability to monitor this
process using the HO2S 1 and the HO2S 2 heated oxygen sensors. The HO2S 1 sensor produces an output signal which indicates the amount of
oxygen present in the exhaust gas entering the three way catalytic converter. The HO2S 2 sensor produces an output signal which indicates the
oxygen storage capacity of the catalyst this in turn indicates the catalysts ability to convert exhaust gases efficiently. If the catalyst is operating
efficiently, the HO2S 1 signal will be far more active than that produced by the HO2S 2 sensor. If the HO2S 2 signal voltage remains at or near
the 450 mV bias for an extended period of time, DTC P0140 will be set.

CONDITIONS FOR RUNNING THE DTC


- Active TP, MAP, MAF, IAT, ECT sensor, fuel injector circuit, or EVAP DTCs are not present.
- AIR pump is commanded OFF.
- ECT is more than 65°C (149°F).
- System voltage is between 9 and 18 volts.
- Engine run time longer than 200 seconds.

CONDITIONS FOR SETTING THE DTC


HO2S 2 signal voltage remains between 412 mV and 499 mV for more than 100 seconds.

ACTION TAKEN WHEN THE DTC SETS


- The PCM will illuminate the Malfunction Indicator Lamp (MIL) during the second consecutive trip in which the diagnostic test has been run
and failed.
- The PCM will store conditions which were present when the DTC set as Freeze Frame and Failure Records data.
- If the misfire is determined to be catalyst damaging, the PCM will flash the MIL.

CONDITIONS FOR CLEARING THE MIL/DTC


- The PCM will turn OFF the MIL during the third consecutive trip in which the diagnostic has been run and passed.
- The History DTC will clear after 40 consecutive warm-up cycles have occurred without a malfunction.
- The DTC can be cleared by using a scan tool.

DIAGNOSTIC AIDS
Inspect for the following conditions:
- Corroded exhaust flange bolts-Using a DMM, ensure that continuity exists between the engine block and the heated oxygen sensor shell. If
resistance is excessively high, replace corroded exhaust flange attaching hardware as necessary.
- Malfunctioning HO2S heater or heater circuit- With the ignition ON, engine not running the HO2S voltage displayed on a scan tool should
gradually drop to below 250 mV or rise to above 600 mV. If not, disconnect the HO2S and connect a test lamp between the HO2S ignition
feed and heater ground circuits. If the test lamp does not illuminate, repair the open ignition feed or sensor ground circuit as necessary. If the
test lamp illuminates and the HO2S signal and low circuits are OK, replace the affected HO2S.

IMPORTANT: Remove any debris from the connector surfaces before servicing a component. Inspect the connector gaskets when diagnosing
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 293
Chevrolet Venture V6-3.4L VIN E 1973
or replacing a component. Ensure that the gaskets are installed correctly. The gaskets prevent contaminate intrusion.

- Poor terminal connection-Inspect the harness connectors for backed out terminals, improper mating, broken locks, improperly formed or
damaged terminals, and faulty terminal to wire connection. Use a corresponding mating terminal to test for proper tension. Refer to
Diagrams.
- Damaged harness-Inspect the wiring harness for damage. If the harness inspection does not reveal a problem, observe the display on the scan
tool while moving connectors and wiring harnesses related to the sensor. A change in the scan tool display may indicate the location of the
fault. Refer to Diagrams.
- PCM and engine grounds for clean and secure connections

If the DTC is determined to be intermittent, reviewing the Failure Records can be useful in determining when the DTC was last set.

TEST DESCRIPTION
The numbers below refer to the step numbers on the diagnostic table:
3. If the DTC P0140 test passes while the Failure Records conditions are being duplicated, an intermittent condition is indicated. Reviewing the
Failure Records vehicle mileage since the diagnostic test last failed may help determine how often the condition that caused the DTC to be set
occurs. This may assist in diagnosing the condition.
12. This vehicle is equipped with a PCM which utilizes an electrically erasable programmable read only memory (EEPROM). When the PCM is
being replaced, the new PCM must be programmed.

P0141

Diagnostic Chart (Part 1 Of 2)


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 294
Chevrolet Venture V6-3.4L VIN E 1974

Diagnostic Chart (Part 2 Of 2)


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 295
Chevrolet Venture V6-3.4L VIN E 1975

Schematic

CIRCUIT DESCRIPTION
Heated oxygen sensors are used to minimize the amount of time required for closed loop fuel control operation and to allow accurate catalyst
monitoring. The oxygen sensor heater greatly decreases the amount of time required for fuel control sensor HO2S 1 to become active. The
oxygen sensor heater is required by catalyst monitor sensor HO2S 2 to maintain a sufficiently high temperature. This allows accurate exhaust
oxygen content readings further from the engine.

The PCM will run the heater test only after a cold start (determined by engine coolant and intake air temperature at the time of start up) and only
once during an ignition cycle. When the engine is started the PCM will monitor the HO2S voltage. When the HO2S voltage indicates a
sufficiently active sensor, the PCM looks at how much time has elapsed since start-up. If the PCM determines that too much time was required
for the HO2S 2 to become active, a DTC P0141 will set. The time required for the HO2S to reach operating temperature is based on the ECT at
start-up and the average MAF since start-up (higher average airflow or higher start-up ECT = shorter time to HO2S activity).

CONDITIONS FOR RUNNING THE DTC


- Active TP, MAP, MAF, ECT, IAT sensor, misfire, fuel injector circuit, EVAP, or AIR DTCs are not present.
- Intake air temperature (IAT) is less than 35°C (95°F) at start up.
- Engine coolant temperature (ECT) is less than 35°C (95°F) at start-up.
- AIR pump is commanded OFF.
- IAT and ECT are within 6°C (43°F) of each other at start-up.
- System voltage between 9.0 volts and 18.0 volts.

CONDITIONS FOR SETTING THE DTC


HO2S 2 voltage remains within 150 mV of the bias voltage (about 450 mV) for a longer amount of time than normally required. The amount of
time varies depending on ECT at start-up and average air flow since start-up, but will not exceed 3 minutes.

ACTION TAKEN WHEN THE DTC SETS


- The PCM will illuminate the Malfunction Indicator Lamp (MIL) during the second consecutive trip in which the diagnostic test has been run
and failed.
- The PCM will store conditions which were present when the DTC set as Freeze Frame and Failure Records data.
- If the misfire is determined to be catalyst damaging, the PCM will flash the MIL.

CONDITIONS FOR CLEARING THE MIL/DTC


- The PCM will turn OFF the MIL during the third consecutive trip in which the diagnostic has been run and passed.
- The History DTC will clear after 40 consecutive warm-up cycles have occurred without a malfunction.
- The DTC can be cleared by using a scan tool.

DIAGNOSTIC AIDS
Inspect for the following conditions:

IMPORTANT: Remove any debris from the connector surfaces before servicing a component. Inspect the connector gaskets when diagnosing
or replacing a component. Ensure that the gaskets are installed correctly. The gaskets prevent contaminate intrusion.
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 296
Chevrolet Venture V6-3.4L VIN E 1976

- Poor terminal connection-Inspect the harness connectors for backed out terminals, improper mating, broken locks, improperly formed or
damaged terminals, and faulty terminal to wire connection. Use a corresponding mating terminal to test for proper tension. Refer to
Diagrams.
- Damaged harness-Inspect the wiring harness for damage. If the harness inspection does not reveal a problem, observe the display on the scan
tool while moving connectors and wiring harnesses related to the sensor. A change in the scan tool display may indicate the location of the
fault. Refer to Diagrams.
- PCM and engine grounds for clean and secure connections

If the DTC is determined to be intermittent, reviewing the Failure Records can be useful in determining when the DTC was last set.

TEST DESCRIPTION
The numbers below refer to the step numbers on the diagnostic table:
2. The HO2S should be allowed to cool before performing this test. If the HO2S heater is functioning the signal voltage will gradually increase
or decrease as the sensor element warms. If the heater is not functioning the HO2S signal will remain near the 450 mV bias voltage.
4. Inspects that the ignition feed circuit to the HO2S is not open or shorted. The test lamp should be connected to a good chassis ground in case
the HO2S low or HO2S heater ground circuit is faulty.
5. Inspects the HO2S heater ground circuit.
6. Inspects for an open or shorted HO2S heater element. The heater element resistance will vary according to HO2S temperature (a hot HO2S
heater element will measure a much higher resistance than a HO2S heater element at room temperature). It is important to allow the HO2S to
cool before measuring HO2S heater element resistance.
11. An open HO2S signal or low circuit can cause the HO2S heater to appear faulty. Inspect these circuits before replacing the sensor.

P0171
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 297
Chevrolet Venture V6-3.4L VIN E 1977

Diagnostic Chart (Part 1 Of 2)


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 298
Chevrolet Venture V6-3.4L VIN E 1978

Diagnostic Chart (Part 2 Of 2)

Fuel Trim Cells

CIRCUIT DESCRIPTION
To provide the best possible combination of driveability, fuel economy, and emission control, a closed loop air/fuel metering system is used.
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 299
Chevrolet Venture V6-3.4L VIN E 1979
While in closed loop, the Powertrain Control Module (PCM) monitors the HO2S 1 signal and adjusts fuel delivery based upon the HO2S signal
voltages. A change made to fuel delivery will be indicated by the long and short term fuel trim values which can be monitored with a scan tool.
Ideal fuel trim values are around 0 percent if the HO2S signals are indicating a lean condition the PCM will add fuel, resulting in fuel trim
values above 0 percent. If a rich condition is detected, the fuel trim values will be below 0 percent, indicating that the PCM is reducing the
amount of fuel delivered. If an excessively lean condition is detected, the PCM will set DTC P0171. The PCMs maximum authority to control
long term fuel trim allows a range between -30 percent and +22 percent. The PCMs maximum authority to control short term fuel trim allows a
range between -27 percent and +27 percent. The PCM monitors fuel trim under various operating conditions (fuel trim cells) before
determining the status of the fuel trim diagnostic. The fuel trim cells are:

The vehicle may have to be operated in all of the above conditions marked by an X, before the PCM determines fuel trim status. The amount of
fuel trim deviates from 0 percent in each cell and the amount that each cell is used directly affects whether or not the vehicle must be operated in
all of the cells described above to complete the diagnostic.

CONDITIONS FOR RUNNING THE DTC


- No MAF, MAP, TP, ECT, IAT, CKP, CAM sensor, Misfire, Fuel Injector, VSS, EST, HO2S, EGR, or EVAP DTCs are set.
- Engine coolant temperature between 20°C (68°F) and 110°C (230°F).
- Intake air temperature is between -18°C (0°F) and 70°C (158°F).
- Manifold absolute pressure is between 18 kPa and 80 kPa.
- Throttle angle is steady and less than 90 percent.
- Vehicle speed is less than 132 km/h (82 mph).
- Engine speed is between 600 and 4000 RPM.
- BARO is greater than 70 kPa.
- Air flow is between 3 gm/s and 150 gm/s.

CONDITIONS FOR SETTING THE DTC


- Long term fuel trim is at or near maximum authority of 20 percent.
- Short term fuel trim is greater than -1 percent.

ACTION TAKEN WHEN THE DTC SETS


- The PCM will illuminate the malfunction indicator lamp (MIL) during the second consecutive trip in which the diagnostic test has been run
and failed.
- The PCM will store conditions which were present when the DTC set as Freeze Frame and Failure Records data.

CONDITIONS FOR CLEARING THE MIL/DTC


- The PCM will turn OFF the MIL during the third consecutive trip in which the diagnostic has been run and passed.
- The History DTC will clear after 40 consecutive warm-up cycles have occurred without a malfunction.
- The DTC can be cleared by using the scan tool.

DIAGNOSTIC AIDS
Inspect for the following conditions:
- Heated oxygen sensor wiring - The sensor pigtail may be routed incorrectly and contacting the exhaust system.
- Fuel pressure low - The system will go lean if pressure is too low. The PCM can compensate for some decrease. However, if fuel pressure is
too low, a DTC P0171 may be set. Refer to Fuel System Pressure Test. See: Fuel Delivery and Air Induction/Fuel Pressure/Testing and
Inspection/Fuel System Pressure Test
- Fuel injectors faulty - Refer to Fuel Injector replacement
- Vacuum leaks - Check for disconnected or damaged vacuum hoses and for vacuum leaks at the intake manifold, throttle body, EGR system,
and crankcase ventilation system. Refer to Visual/Physical Inspection using the Emission Hose Routing Diagram.
- Exhaust leaks - An exhaust leak may cause outside air to be pulled into the exhaust gas stream past the HO2S, causing the system to appear
lean. Check for exhaust leaks that may cause a false lean condition to be indicated.
- Disconnect the MAF sensor and see if the lean condition is corrected. If so, replace MAF sensor.
- Fuel contamination - Water, even in small amounts, can be delivered to the fuel injectors. The water can cause a lean exhaust to be indicated.
Excessive alcohol in the fuel can also cause this condition. Refer to Alcohol/Contaminants-in-Fuel Diagnosis. See: Component Tests and
General Diagnostics/Fuel Quality Diagnosis

IMPORTANT: Remove any debris from the connector surfaces before servicing a component. Inspect the connector gaskets when diagnosing
or replacing a component. Ensure that the gaskets are installed correctly. The gaskets prevent contaminate intrusion.

- Poor terminal connection-Inspect the harness connectors for backed out terminals, improper mating, broken locks, improperly formed or
damaged terminals, and faulty terminal to wire connection. Use a corresponding mating terminal to test for proper tension. Refer to
Diagrams.
- Damaged harness-Inspect the wiring harness for damage. If the harness inspection does not reveal a problem, observe the display on the scan
tool while moving connectors and wiring harnesses related to the sensor. A change in the scan tool display may indicate the location of the
fault. Refer to Diagrams.
- PCM and engine grounds for clean and secure connections

If the DTC is determined to be intermittent, reviewing the Failure Records can be useful in determining when the DTC was last set.

TEST DESCRIPTION
The numbers below refer to the step numbers on the Diagnostic Table:
2. DTCs other than P0171 may indicate a condition present which may cause a lean condition. If this is the case, repairing the condition which
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 300
Chevrolet Venture V6-3.4L VIN E 1980
caused the other DTC will most likely correct the DTC P0171.
4. If the DTC P0171 test passes while the Fail Records conditions are being duplicated, the lean condition is intermittent. Refer to Diagnostic
Aids or Symptoms for additional information on diagnosing intermittent problems.

P0172

Fuel Trim Cells


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 301
Chevrolet Venture V6-3.4L VIN E 1981

Diagnostic Chart (Part 1 Of 2)


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 302
Chevrolet Venture V6-3.4L VIN E 1982

Diagnostic Chart (Part 2 Of 2)

CIRCUIT DESCRIPTION
To provide the best possible combination of driveability, fuel economy, and emission control, a closed loop air/fuel metering system is used.
While in closed loop, the Powertrain Control (PCM) monitors the HO2S 1 signal and adjusts fuel delivery based upon the HO2S signal voltages.
A change made to fuel delivery will be indicated by the long and short term fuel trim values which can be monitored with a scan tool. Ideal fuel
trim values are around 0 percent if the HO2S signals are indicating a lean condition the PCM will add fuel, resulting in fuel trim values above 0
percent. If a rich condition is detected, the fuel trim values will be below 0 percent, indicating that the PCM is reducing the amount of fuel
delivered. If an excessively rich condition is detected, the PCM will set DTC P0172. The PCMs maximum authority to control long term fuel
trim allows a range between -30 percent and +22 percent. The PCMs maximum authority to control short term fuel trim allows a range between
-27 percent and +27 percent. The PCM monitors fuel trim under various operating conditions (fuel trim cells) before determining the status of
the fuel trim diagnostic. The fuel trim cells are:

The vehicle may have to be operated in all of the above conditions marked by an X, before the PCM determines fuel trim status. The amount of
fuel trim deviates from 0 percent in each cell and the amount that each cell is used directly affects whether or not the vehicle must be operated in
all of the cells described above to complete the diagnostic.

CONDITIONS FOR RUNNING THE DTC


- No MAF, ECT, TP, MAP, CMP, CKP, IAT sensor, EVAP, EGR, HO2S, Misfire, Injector circuit, Idle speed, VSS, or IC circuit DTCs set.
- Engine coolant temperature between 20°C (68°F) and 110°C (230°F).
- Intake air temperature is between -18°C (0°F) and 70°C (158°F).
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 303
Chevrolet Venture V6-3.4L VIN E 1983
- Manifold absolute pressure is between 18 kPa and 80 kPa.
- Throttle angle is steady and less than 90 percent.
- Vehicle speed is less than 132 km/h (82 mph).
- Engine speed is between 600 and 4000 RPM.
- BARO is greater than 70 kPa.
- Air flow is between 3 gm/s and 150 gm/s.

CONDITIONS FOR SETTING THE DTC


- Long term fuel trim is at or near maximum authority of -19 percent.
- Short term fuel trim is at or near maximum authority of 1 percent.
- All conditions have been met in the fuel trim cells.

ACTION TAKEN WHEN THE DTC SETS


- The PCM will illuminate the Malfunction Indicator Lamp (MIL) during the second consecutive trip in which the diagnostic test has been run
and failed.
- The PCM will store conditions which were present when the DTC set as Freeze Frame and Failure Records data.

CONDITIONS FOR CLEARING THE MIL/DTC


- The PCM will turn OFF the MIL during the third consecutive trip in which the diagnostic has been run and passed.
- The History DTC will clear after 40 consecutive warm-up cycles have occurred without a malfunction.
- The DTC can be cleared by using the scan tool.

DIAGNOSTIC AIDS
Inspect the following items:
- Fuel pressure high - The system will go rich if pressure is too high. The PCM can compensate for some increase. However, if fuel pressure is
too high, a DTC P0172 may be set. Refer to Fuel System Pressure Test. See: Fuel Delivery and Air Induction/Fuel Pressure/Testing and
Inspection/Fuel System Pressure Test
- Fuel injectors faulty - Refer to Fuel Injector Balance Test. See: Component Tests and General Diagnostics/Fuel Injector Balance Test
- Inspect the EVAP canister for fuel saturation. If the EVAP canister is full of fuel, check canister control and hoses.
- Disconnect the MAF sensor and see if rich condition is corrected. If so, replace the MAF sensor.
- Inspect for a leaking fuel pressure regulator diaphragm by checking the vacuum line to the fuel pressure regulator for the presence of fuel.
- An intermittent TP sensor output will cause the system to go rich due to a false indication of the engine accelerating.

IMPORTANT: Remove any debris from the connector surfaces before servicing a component. Inspect the connector gaskets when diagnosing
or replacing a component. Ensure that the gaskets are installed correctly. The gaskets prevent contaminate intrusion.

- Poor terminal connection-Inspect the harness connectors for backed out terminals, improper mating, broken locks, improperly formed or
damaged terminals, and faulty terminal to wire connection. Use a corresponding mating terminal to test for proper tension. Refer to
Diagrams.
- Damaged harness-Inspect the wiring harness for damage. If the harness inspection does not reveal a problem, observe the display on the scan
tool while moving connectors and wiring harnesses related to the sensor. A change in the scan tool display may indicate the location of the
fault. Refer to Diagrams.
- PCM and engine grounds for clean and secure connections

If the DTC is determined to be intermittent, reviewing the Failure Records can be useful in determining when the DTC was last set.

TEST DESCRIPTION
The numbers below refer to the step numbers on the Diagnostic Table:
2. DTCs other than P0172 may indicate a condition present which may cause a lean condition. If this is the case, repairing the condition which
caused the other DTC will most likely correct the DTC P0172.
4. If the DTC P0172 test passes while the Fail Records conditions are being duplicated, the rich condition is intermittent. Refer to Diagnostic
Aids for additional information on diagnosing intermittent conditions.
P0201
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 304
Chevrolet Venture V6-3.4L VIN E 1984

Diagnostic Chart (Part 1 Of 2)


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 305
Chevrolet Venture V6-3.4L VIN E 1985

Diagnostic Chart (Part 2 Of 2)

Refer to Engine Controls Schematics. See: Diagrams/Electrical Diagrams

CIRCUIT DESCRIPTION
The PCM controls the fuel injector control circuit using a Multi Function Driver (MFD). The MFD has the ability to detect an electrical
malfunction. If an electrical malfunction is detected, the MFD signals the PCM to set this DTC.

CONDITIONS FOR RUNNING THE DTC


The ignition is ON.

CONDITIONS FOR SETTING THE DTC


- An incorrect voltage level is being detected on an injector driver circuit.
- Above condition for over 30 seconds.

ACTION TAKEN WHEN THE DTC SETS


- The PCM will illuminate the Malfunction Indicator Lamp (MIL) during the second consecutive trip in which the diagnostic test has been run
and failed.
- The PCM will store conditions which were present when the DTC set as Freeze Frame and Failure Records data.
- If the misfire is determined to be catalyst damaging, the PCM will flash the MIL.

CONDITIONS FOR CLEARING THE MIL/DTC


- The PCM will turn OFF the MIL during the third consecutive trip in which the diagnostic has been run and passed.
- The History DTC will clear after 40 consecutive warm-up cycles have occurred without a malfunction.
- The DTC can be cleared by using a scan tool.

DIAGNOSTIC AIDS
Inspect for the following conditions:

IMPORTANT: Remove any debris from the connector surfaces before servicing a component. Inspect the connector gaskets when diagnosing
or replacing a component. Ensure that the gaskets are installed correctly. The gaskets prevent contaminate intrusion.

- Poor terminal connection-Inspect the harness connectors for backed out terminals, improper mating, broken locks, improperly formed or
damaged terminals, and faulty terminal to wire connection. Use a corresponding mating terminal to test for proper tension. Refer to
Diagrams.
- Damaged harness-Inspect the wiring harness for damage. If the harness inspection does not reveal a problem, observe the display on the scan
tool while moving connectors and wiring harnesses related to the sensor. A change in the scan tool display may indicate the location of the
fault. Refer to Diagrams.
- PCM and engine grounds for clean and secure connections
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 306
Chevrolet Venture V6-3.4L VIN E 1986

If the DTC is determined to be intermittent, reviewing the Failure Records can be useful in determining when the DTC was last set.

TEST DESCRIPTION
The number(s) below refer to the step number(s) on the diagnostic table:
4. If the scan tool indicates STUCK HIGH there is a short to battery positive voltage on the fuel injector control circuit.
5. If the scan tool indicates STUCK LOW there is an open or a short to ground on the fuel injector control circuit.
6. When the multiple-way connector is disconnected, other DTCs will be set. These DTCs should be disregarded.
If the scan tool indicates a STUCK HIGH while cranking, the short to battery positive voltage is between the multiple-way connector and the
PCM. If the scan tool indicates STUCK LOW while cranking the short to battery positive voltage is between the multiple-way connector and
the fuel injector.

IMPORTANT: While cranking the engine with the multiple-way connector disconnected, all of the other injector circuits should indicate
STUCK LOW, this is a fault induced by disconnecting this connector. They will resume correct operation when the connector is reconnected.

9. This step is testing for a short to ground in the circuit.


10. The fuel injector in this circuit will need to be tested after the short to ground is repaired or after the PCM is replaced.
11. This step is testing the function of the PCM. If the test lamp flashes then the PCM is able to supply the ground.
14. This vehicle is equipped with a PCM which utilizes an Electronically Erasable Programmable Read Only Memory (EEPROM). When the
PCM is replaced, the new PCM must be programmed.

P0202
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 307
Chevrolet Venture V6-3.4L VIN E 1987

Diagnostic Chart (Part 1 Of 2)


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 308
Chevrolet Venture V6-3.4L VIN E 1988

Diagnostic Chart (Part 2 Of 2)

Refer to Engine Controls Schematics. See: Diagrams/Electrical Diagrams

CIRCUIT DESCRIPTION
The PCM controls the fuel injector control circuit using a Multi Function Driver (MFD). The MFD has the ability to detect an electrical
malfunction. If an electrical malfunction is detected, the MFD signals the PCM to set this DTC.

CONDITIONS FOR RUNNING THE DTC


The ignition is ON.

CONDITIONS FOR SETTING THE DTC


- An incorrect voltage level is being detected on an injector driver circuit.
- Above condition for over 30 seconds.

ACTION TAKEN WHEN THE DTC SETS


- The PCM will illuminate the Malfunction Indicator Lamp (MIL) during the second consecutive trip in which the diagnostic test has been run
and failed.
- The PCM will store conditions which were present when the DTC set as Freeze Frame and Failure Records data.
- If the misfire is determined to be catalyst damaging, the PCM will flash the MIL.

CONDITIONS FOR CLEARING THE MIL/DTC


- The PCM will turn OFF the MIL during the third consecutive trip in which the diagnostic has been run and passed.
- The History DTC will clear after 40 consecutive warm-up cycles have occurred without a malfunction.
- The DTC can be cleared by using a scan tool.

DIAGNOSTIC AIDS
Inspect for the following conditions:

IMPORTANT: Remove any debris from the connector surfaces before servicing a component. Inspect the connector gaskets when diagnosing
or replacing a component. Ensure that the gaskets are installed correctly. The gaskets prevent contaminate intrusion.

- Poor terminal connection-Inspect the harness connectors for backed out terminals, improper mating, broken locks, improperly formed or
damaged terminals, and faulty terminal to wire connection. Use a corresponding mating terminal to test for proper tension. Refer to
Diagrams.
- Damaged harness-Inspect the wiring harness for damage. If the harness inspection does not reveal a problem, observe the display on the scan
tool while moving connectors and wiring harnesses related to the sensor. A change in the scan tool display may indicate the location of the
fault. Refer to Diagrams.
- PCM and engine grounds for clean and secure connections
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 309
Chevrolet Venture V6-3.4L VIN E 1989

If the DTC is determined to be intermittent, reviewing the Failure Records can be useful in determining when the DTC was last set.

TEST DESCRIPTION
The number(s) below refer to the step number(s) on the diagnostic table:
4. If the scan tool indicates STUCK HIGH there is a short to battery positive voltage on the fuel injector control circuit.
5. If the scan tool indicates STUCK LOW there is an open or a short to ground on the fuel injector control circuit.
6. When the multiple-way connector is disconnected, other DTCs will be set. These DTCs should be disregarded.
If the scan tool indicates a STUCK HIGH while cranking, the short to battery positive voltage is between the multiple-way connector and the
PCM. If the scan tool indicates STUCK LOW while cranking the short to battery positive voltage is between the multiple-way connector and
the fuel injector.

IMPORTANT: While cranking the engine with the multiple-way connector disconnected, all of the other injector circuits should indicate
STUCK LOW, this is a fault induced by disconnecting this connector. They will resume correct operation when the connector is reconnected.

9. This step is testing for a short to ground in the circuit.


10. The fuel injector in this circuit will need to be tested after the short to ground is repaired or after the PCM is replaced.
11. This step is testing the function of the PCM. If the test lamp flashes then the PCM is able to supply the ground.
14. This vehicle is equipped with a PCM which utilizes an Electronically Erasable Programmable Read Only Memory (EEPROM). When the
PCM is replaced, the new PCM must be programmed.

P0203
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 310
Chevrolet Venture V6-3.4L VIN E 1990

Diagnostic Chart (Part 1 Of 2)


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 311
Chevrolet Venture V6-3.4L VIN E 1991

Diagnostic Chart (Part 2 Of 2)

Refer to Engine Controls Schematics. See: Diagrams/Electrical Diagrams

CIRCUIT DESCRIPTION
The PCM controls the fuel injector control circuit using a Multi Function Driver (MFD). The MFD has the ability to detect an electrical
malfunction. If an electrical malfunction is detected, the MFD signals the PCM to set this DTC.

CONDITIONS FOR RUNNING THE DTC


The ignition is ON.

CONDITIONS FOR SETTING THE DTC


- An incorrect voltage level is being detected on an injector driver circuit.
- Above condition for over 30 seconds.

ACTION TAKEN WHEN THE DTC SETS


- The PCM will illuminate the Malfunction Indicator Lamp (MIL) during the second consecutive trip in which the diagnostic test has been run
and failed.
- The PCM will store conditions which were present when the DTC set as Freeze Frame and Failure Records data.
- If the misfire is determined to be catalyst damaging, the PCM will flash the MIL.

CONDITIONS FOR CLEARING THE MIL/DTC


- The PCM will turn OFF the MIL during the third consecutive trip in which the diagnostic has been run and passed.
- The History DTC will clear after 40 consecutive warm-up cycles have occurred without a malfunction.
- The DTC can be cleared by using a scan tool.

DIAGNOSTIC AIDS
Inspect for the following conditions:

IMPORTANT: Remove any debris from the connector surfaces before servicing a component. Inspect the connector gaskets when diagnosing
or replacing a component. Ensure that the gaskets are installed correctly. The gaskets prevent contaminate intrusion.

- Poor terminal connection-Inspect the harness connectors for backed out terminals, improper mating, broken locks, improperly formed or
damaged terminals, and faulty terminal to wire connection. Use a corresponding mating terminal to test for proper tension. Refer to
Diagrams.
- Damaged harness-Inspect the wiring harness for damage. If the harness inspection does not reveal a problem, observe the display on the scan
tool while moving connectors and wiring harnesses related to the sensor. A change in the scan tool display may indicate the location of the
fault. Refer to Diagrams.
- PCM and engine grounds for clean and secure connections
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 312
Chevrolet Venture V6-3.4L VIN E 1992

If the DTC is determined to be intermittent, reviewing the Failure Records can be useful in determining when the DTC was last set.

TEST DESCRIPTION
The number(s) below refer to the step number(s) on the diagnostic table:
4. If the scan tool indicates STUCK HIGH there is a short to battery positive voltage on the fuel injector control circuit.
5. If the scan tool indicates STUCK LOW there is an open or a short to ground on the fuel injector control circuit.
6. When the multiple-way connector is disconnected, other DTCs will be set. These DTCs should be disregarded.
If the scan tool indicates a STUCK HIGH while cranking, the short to battery positive voltage is between the multiple-way connector and the
PCM. If the scan tool indicates STUCK LOW while cranking the short to battery positive voltage is between the multiple-way connector and
the fuel injector.

IMPORTANT: While cranking the engine with the multiple-way connector disconnected, all of the other injector circuits should indicate
STUCK LOW, this is a fault induced by disconnecting this connector. They will resume correct operation when the connector is reconnected.

9. This step is testing for a short to ground in the circuit.


10. The fuel injector in this circuit will need to be tested after the short to ground is repaired or after the PCM is replaced.
11. This step is testing the function of the PCM. If the test lamp flashes then the PCM is able to supply the ground.
14. This vehicle is equipped with a PCM which utilizes an Electronically Erasable Programmable Read Only Memory (EEPROM). When the
PCM is replaced, the new PCM must be programmed.

P0204
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 313
Chevrolet Venture V6-3.4L VIN E 1993

Diagnostic Chart (Part 1 Of 2)


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 314
Chevrolet Venture V6-3.4L VIN E 1994

Diagnostic Chart (Part 2 Of 2)

Refer to Engine Controls Schematics. See: Diagrams/Electrical Diagrams

CIRCUIT DESCRIPTION
The PCM controls the fuel injector control circuit using a Multi Function Driver (MFD). The MFD has the ability to detect an electrical
malfunction. If an electrical malfunction is detected, the MFD signals the PCM to set this DTC.

CONDITIONS FOR RUNNING THE DTC


The ignition is ON.

CONDITIONS FOR SETTING THE DTC


- An incorrect voltage level is being detected on an injector driver circuit.
- Above condition for over 30 seconds.

ACTION TAKEN WHEN THE DTC SETS


- The PCM will illuminate the Malfunction Indicator Lamp (MIL) during the second consecutive trip in which the diagnostic test has been run
and failed.
- The PCM will store conditions which were present when the DTC set as Freeze Frame and Failure Records data.
- If the misfire is determined to be catalyst damaging, the PCM will flash the MIL.

CONDITIONS FOR CLEARING THE MIL/DTC


- The PCM will turn OFF the MIL during the third consecutive trip in which the diagnostic has been run and passed.
- The History DTC will clear after 40 consecutive warm-up cycles have occurred without a malfunction.
- The DTC can be cleared by using a scan tool.

DIAGNOSTIC AIDS
Inspect for the following conditions:

IMPORTANT: Remove any debris from the connector surfaces before servicing a component. Inspect the connector gaskets when diagnosing
or replacing a component. Ensure that the gaskets are installed correctly. The gaskets prevent contaminate intrusion.

- Poor terminal connection-Inspect the harness connectors for backed out terminals, improper mating, broken locks, improperly formed or
damaged terminals, and faulty terminal to wire connection. Use a corresponding mating terminal to test for proper tension. Refer to
Diagrams.
- Damaged harness-Inspect the wiring harness for damage. If the harness inspection does not reveal a problem, observe the display on the scan
tool while moving connectors and wiring harnesses related to the sensor. A change in the scan tool display may indicate the location of the
fault. Refer to Diagrams.
- PCM and engine grounds for clean and secure connections
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 315
Chevrolet Venture V6-3.4L VIN E 1995

If the DTC is determined to be intermittent, reviewing the Failure Records can be useful in determining when the DTC was last set.

TEST DESCRIPTION
The number(s) below refer to the step number(s) on the diagnostic table:
4. If the scan tool indicates STUCK HIGH there is a short to battery positive voltage on the fuel injector control circuit.
5. If the scan tool indicates STUCK LOW there is an open or a short to ground on the fuel injector control circuit.
6. When the multiple-way connector is disconnected, other DTCs will be set. These DTCs should be disregarded.
If the scan tool indicates a STUCK HIGH while cranking, the short to battery positive voltage is between the multiple-way connector and the
PCM. If the scan tool indicates STUCK LOW while cranking the short to battery positive voltage is between the multiple-way connector and
the fuel injector.

IMPORTANT: While cranking the engine with the multiple-way connector disconnected, all of the other injector circuits should indicate
STUCK LOW, this is a fault induced by disconnecting this connector. They will resume correct operation when the connector is reconnected.

9. This step is testing for a short to ground in the circuit.


10. The fuel injector in this circuit will need to be tested after the short to ground is repaired or after the PCM is replaced.
11. This step is testing the function of the PCM. If the test lamp flashes then the PCM is able to supply the ground.
14. This vehicle is equipped with a PCM which utilizes an Electronically Erasable Programmable Read Only Memory (EEPROM). When the
PCM is replaced, the new PCM must be programmed.

P0205
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 316
Chevrolet Venture V6-3.4L VIN E 1996

Diagnostic Chart (Part 1 Of 2)


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 317
Chevrolet Venture V6-3.4L VIN E 1997

Diagnostic Chart (Part 2 Of 2)

Refer to Engine Controls Schematics. See: Diagrams/Electrical Diagrams

CIRCUIT DESCRIPTION
The PCM controls the fuel injector control circuit using a Multi Function Driver (MFD). The MFD has the ability to detect an electrical
malfunction. If an electrical malfunction is detected, the MFD signals the PCM to set this DTC.

CONDITIONS FOR RUNNING THE DTC


The ignition is ON.

CONDITIONS FOR SETTING THE DTC


- An incorrect voltage level is being detected on an injector driver circuit.
- Above condition for over 30 seconds.

ACTION TAKEN WHEN THE DTC SETS


- The PCM will illuminate the malfunction indicator lamp (MIL) during the second consecutive trip in which the diagnostic test has been run
and failed.
- The PCM will store conditions which were present when the DTC set as Freeze Frame and Failure Records data.
- If the misfire is determined to be catalyst damaging, the PCM will flash the MIL.

CONDITIONS FOR CLEARING THE MIL/DTC


- The PCM will turn OFF the MIL during the third consecutive trip in which the diagnostic has been run and passed.
- The History DTC will clear after 40 consecutive warm-up cycles have occurred without a malfunction.
- The DTC can be cleared by using a scan tool.

DIAGNOSTIC AIDS
Inspect for the following conditions:

IMPORTANT: Remove any debris from the connector surfaces before servicing a component. Inspect the connector gaskets when diagnosing
or replacing a component. Ensure that the gaskets are installed correctly. The gaskets prevent contaminate intrusion.

- Poor terminal connection-Inspect the harness connectors for backed out terminals, improper mating, broken locks, improperly formed or
damaged terminals, and faulty terminal to wire connection. Use a corresponding mating terminal to test for proper tension. Refer to
Diagrams.
- Damaged harness-Inspect the wiring harness for damage. If the harness inspection does not reveal a problem, observe the display on the scan
tool while moving connectors and wiring harnesses related to the sensor. A change in the scan tool display may indicate the location of the
fault. Refer to Diagrams.
- PCM and engine grounds for clean and secure connections
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 318
Chevrolet Venture V6-3.4L VIN E 1998

If the DTC is determined to be intermittent, reviewing the Failure Records can be useful in determining when the DTC was last set.

TEST DESCRIPTION
The number(s) below refer to the step number(s) on the diagnostic table:
4. If the scan tool indicates STUCK HIGH there is a short to battery positive voltage on the fuel injector control circuit.
5. If the scan tool indicates STUCK LOW there is an open or a short to ground on the fuel injector control circuit.
6. When the multiple-way connector is disconnected, other DTCs will be set. These DTCs should be disregarded.
If the scan tool indicates a STUCK HIGH while cranking, the short to battery positive voltage is between the multiple-way connector and the
PCM. If the scan tool indicates STUCK LOW while cranking the short to battery positive voltage is between the multiple-way connector and
the fuel injector.

IMPORTANT: While cranking the engine with the multiple-way connector disconnected, all of the other injector circuits should indicate
STUCK LOW, this is a fault induced by disconnecting this connector. They will resume correct operation when the connector is reconnected.

9. This step is testing for a short to ground in the circuit.


10. The fuel injector in this circuit will need to be tested after the short to ground is repaired or after the PCM is replaced.
11. This step is testing the function of the PCM. If the test lamp flashes then the PCM is able to supply the ground.
14. This vehicle is equipped with a PCM which utilizes an Electronically Erasable Programmable Read Only Memory (EEPROM). When the
PCM is replaced, the new PCM must be programmed.
P0206
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 319
Chevrolet Venture V6-3.4L VIN E 1999

Diagnostic Chart (Part 1 Of 2)


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 320
Chevrolet Venture V6-3.4L VIN E 2000

Diagnostic Chart (Part 2 Of 2)

Refer to Engine Controls Schematics. See: Diagrams/Electrical Diagrams

CIRCUIT DESCRIPTION
The PCM controls the fuel injector control circuit using a Multi Function Driver (MFD). The MFD has the ability to detect an electrical
malfunction. If an electrical malfunction is detected, the MFD signals the PCM to set this DTC.

CONDITIONS FOR RUNNING THE DTC


The ignition is ON.

CONDITIONS FOR SETTING THE DTC


- An incorrect voltage level is being detected on an injector driver circuit.
- Above condition for over 30 seconds.

ACTION TAKEN WHEN THE DTC SETS


- The PCM will illuminate the Malfunction Indicator Lamp (MIL) during the second consecutive trip in which the diagnostic test has been run
and failed.
- The PCM will store conditions which were present when the DTC set as Freeze Frame and Failure Records data.
- If the misfire is determined to be catalyst damaging, the PCM will flash the MIL.

CONDITIONS FOR CLEARING THE MIL/DTC


- The PCM will turn OFF the MIL during the third consecutive trip in which the diagnostic has been run and passed.
- The History DTC will clear after 40 consecutive warm-up cycles have occurred without a malfunction.
- The DTC can be cleared by using a scan tool.

DIAGNOSTIC AIDS
Inspect for the following conditions:

IMPORTANT: Remove any debris from the connector surfaces before servicing a component. Inspect the connector gaskets when diagnosing
or replacing a component. Ensure that the gaskets are installed correctly. The gaskets prevent contaminate intrusion.

- Poor terminal connection-Inspect the harness connectors for backed out terminals, improper mating, broken locks, improperly formed or
damaged terminals, and faulty terminal to wire connection. Use a corresponding mating terminal to test for proper tension. Refer to
Diagrams.
- Damaged harness-Inspect the wiring harness for damage. If the harness inspection does not reveal a problem, observe the display on the scan
tool while moving connectors and wiring harnesses related to the sensor. A change in the scan tool display may indicate the location of the
fault. Refer to Diagrams.
- PCM and engine grounds for clean and secure connections
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 321
Chevrolet Venture V6-3.4L VIN E 2001

If the DTC is determined to be intermittent, reviewing the Failure Records can be useful in determining when the DTC was last set.

TEST DESCRIPTION
The number(s) below refer to the step number(s) on the diagnostic table:
4. If the scan tool indicates STUCK HIGH there is a short to battery positive voltage on the fuel injector control circuit.
5. If the scan tool indicates STUCK LOW there is an open or a short to ground on the fuel injector control circuit.
6. When the multiple-way connector is disconnected, other DTCs will be set. These DTCs should be disregarded.
If the scan tool indicates a STUCK HIGH while cranking, the short to battery positive voltage is between the multiple-way connector and the
PCM. If the scan tool indicates STUCK LOW while cranking the short to battery positive voltage is between the multiple-way connector and
the fuel injector.

IMPORTANT: While cranking the engine with the multiple-way connector disconnected, all of the other injector circuits should indicate
STUCK LOW, this is a fault induced by disconnecting this connector. They will resume correct operation when the connector is reconnected.

9. This step is testing for a short to ground in the circuit.


10. The fuel injector in this circuit will need to be tested after the short to ground is repaired or after the PCM is replaced.
11. This step is testing the function of the PCM. If the test lamp flashes then the PCM is able to supply the ground.
14. This vehicle is equipped with a PCM which utilizes an Electronically Erasable Programmable Read Only Memory (EEPROM). When the
PCM is replaced, the new PCM must be programmed.

P0218
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 322
Chevrolet Venture V6-3.4L VIN E 2002

Diagnostic Chart
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 323
Chevrolet Venture V6-3.4L VIN E 2003

Schematic

Circuit Description with 4T65-E Automatic Transaxle


Transmission fluid is drawn from the bottom pan through the filter, case assembly, channel plate assembly, control valve body assembly and into
the oil pump assembly. The pump is mounted on the control valve body assembly. Fluid pressure leaving the pump is controlled by the pressure
regulator valve and becomes the main supply of line pressure to the various components and hydraulic circuits.

Hot fluid from the torque converter flows through the TCC control valve into the cooler lines to the oil cooler located in the vehicle radiator (and
auxiliary cooler if equipped). Cool fluid then returns to lubricate the final drive assembly and other components along the output shaft.

If the Powertrain Control Module (PCM) detects a high temperature on the Transmission Fluid Temperature (TFT) sensor circuit for an
extended period of time, then DTC P0218 sets. DTC P0218 is a type C DTC.

CONDITIONS FOR RUNNING THE DTC


No TFT sensor DTC P0711, P0712 or P0713.

CONDITIONS FOR SETTING THE DTC


The transmission fluid temperature is greater than 130°C (266°F) for 10 minutes.

ACTION TAKEN WHEN THE DTC SETS


^ The PCM does not illuminate the Malfunction Indicator Lamp (MIL).
^ The PCM freezes shift adapts.
^ The PCM records the operating conditions when the Conditions for Setting the DTC are met. The PCM stores this information as Freeze
Frame Records.
^ The PCM stores DTC P0218 in PCM history.

CONDITIONS FOR CLEARING THE DTC


^ A scan tool can clear the DTC.
^ The PCM clears the DTC from PCM history if the vehicle completes 40 consecutive warm-up cycles without a non-emission-related
diagnostic fault occurring.
^ The PCM cancels the DTC default actions when the fault no longer exists and the ignition switch is OFF long enough in order to power down
the PCM.

DIAGNOSTIC AIDS
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 324
Chevrolet Venture V6-3.4L VIN E 2004
^ Inspect the transmission cooling system for possible blockage and restrictions.
^ Ask the customer about possible overloading, exceeding the trailer towing limit, or towing in overdrive.

TEST DESCRIPTION
The numbers below refer to the step numbers on the diagnostic table:
2. This step ensures that the transmission fluid is at the proper level. A low fluid level may cause an over temperature condition.

P0230

Diagnostic Chart
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 325
Chevrolet Venture V6-3.4L VIN E 2005

Schematic

CIRCUIT DESCRIPTION
The Powertrain Control Module (PCM) provides ignition positive voltage to control the fuel pump relay. The PCM has the ability to detect an
electrical malfunction on the relay control circuit. When the ignition switch is first turned ON, the PCM energizes the fuel pump relay which
applies power to the fuel pump. The fuel pump relay will remain ON as long as the engine is running or cranking and the PCM is receiving
reference pulses. If no reference pulses are present, the PCM de-energizes the fuel pump relay within 2 seconds after the ignition is turned ON or
the engine is stopped. With the engine stopped, the fuel pump can be turned ON by using the scan tool output controls function. If an electrical
malfunction is detected, the PCM will set DTC P0230.

CONDITIONS FOR RUNNING THE DTC


- The ignition is ON.
- System voltage is between 9.0 and 18.0 volts.

CONDITIONS FOR SETTING THE DTC


- The PCM detects an electrical malfunction on the fuel pump relay control circuit.
- The condition is present for more than 1 second.

ACTION TAKEN WHEN THE DTC SETS


- The PCM will not illuminate the Malfunction Indicator Lamp (MIL).
- The PCM will store conditions which were present when the DTC set as Failure Records data only. This information will not be stored as
Freeze Frame data.

CONDITIONS FOR CLEARING THE MIL/DTC


- A History DTC will clear after 40 consecutive warm-up cycles have occurred without a malfunction.
- The DTC can be cleared by using the scan tool Clear Info function.

DIAGNOSTIC AIDS
Inspect for the following conditions:

TEST DESCRIPTION
The numbers below refer to the step numbers on the diagnostic table:
2. Listen for an click when the relay operates. Command both the ON and OFF states. Repeat the commands as necessary.
3. Verifies that the PCM is providing voltage to the relay.
4. Tests for an open in the ground circuit to the relay
5. Tests if voltage is constantly being applied to the relay.
12. The PCM utilizes an Electrically Erasable Programmable Read Only Memory (EEPROM). When the PCM is replaced, the new PCM must
be programmed.

P0300
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 326
Chevrolet Venture V6-3.4L VIN E 2006

Diagnostic Chart (Part 1 Of 3)


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 327
Chevrolet Venture V6-3.4L VIN E 2007

Diagnostic Chart (Part 2 Of 3)


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 328
Chevrolet Venture V6-3.4L VIN E 2008

Diagnostic Chart (Part 3 Of 3)

Refer to Engine Controls Schematic Icons in Diagrams. See: Diagrams/Electrical Diagrams

CIRCUIT DESCRIPTION
The PCM has the ability to detect a misfire by monitoring the 3X reference from the Ignition Control (IC) module and camshaft position input
signals from the Camshaft Position (CMP) sensor. The PCM monitors crankshaft speed variations, reference period differences, to determine if a
misfire is occurring.

If 2 percent or more of all cylinder firing events are misfires, emission levels may exceed mandated standards. The PCM determines misfire
level based on the number of misfire events monitored during a 200 engine revolution test sample. The PCM continuously tracks 16 consecutive
200 revolution test samples. If 22 or more misfires are detected during any 10 of the 16 samples, DTC P0300 will set. If the misfire is large
enough to cause possible 3-way catalytic converter damage, DTC P0300 may set during the first 200 revolution sample in which the misfire was
detected. In the case of a catalyst damaging misfire, the MIL will flash to alert the vehicle operator of the potential of catalyst damage.

CONDITIONS FOR RUNNING THE DTC


- TP, MAP, ECT, CKP, CMP, MAF sensor, VSS, DTCs are not set.
- Engine speed is between 525 and 5900 RPM.
- System voltage is between 9.0 and 18.0 volts.
- The ECT indicates an engine temperature between 70°C (21°F) and 1250°C (253°F).
- Throttle angle is steady.

CONDITIONS FOR SETTING THE DTC


The PCM is detecting a crankshaft RPM variation indicating a misfire sufficient to cause 3-way catalytic converter damage or emissions levels to
exceed mandated standard.

ACTION TAKEN WHEN THE DTC SETS


- The PCM will illuminate the Malfunction Indicator Lamp (MIL) during the second consecutive trip in which the diagnostic test has been run
and failed.
- The PCM will store conditions which were present when the DTC set as Freeze Frame and Failure Records data.
- If the misfire is determined to be catalyst damaging, the PCM will flash the MIL.

CONDITIONS FOR CLEARING THE MIL/DTC


- The PCM will turn OFF the MIL during the third consecutive trip in which the diagnostic has been run and passed.
- The History DTC will clear after 40 consecutive warm-up cycles have occurred without a malfunction.
- The DTC can be cleared by using a scan tool.

DIAGNOSTIC AIDS
- The scan tool provides information that can be useful in identifying the misfiring cylinder. If the DTC P0300 is currently stored as Test failed
since code clear, the misfire history counters (Misfire History numbers 1 and 6) will still contain a value that represents the level of misfire
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 329
Chevrolet Venture V6-3.4L VIN E 2009
for each cylinder.
- A misfire DTC may set if components that affect the crankshaft position sensor have recently been replaced, and the CKP System Variation
Learn Procedure has not been performed. If the diagnostic table does not identify a problem then perform the CKP System Variation Learn
Procedure. The Crankshaft Position Variation Learn Procedure should be performed if any of the following conditions are true:
- The PCM has been replaced.
- DTC P1336 is set.
- The engine has been replaced.
- The crankshaft has been replaced.
- The crankshaft harmonic balancer has been replaced.
- The crankshaft position sensor has been replaced.
- The scan tool displayed misfire counter values (Misfire History numbers 1 through 6) can be useful in determining whether the misfire is
isolated to a single cylinder or to a cylinder pair, cylinders that share an ignition coil-1 and 4, 2 and 5, 3 and 6. If the largest amount of
activity is isolated to a cylinder pair, inspect the following components:
- Secondary Ignition Wires-Inspect wires for affected cylinder pair for disconnected ignition wires or for excessive resistance. The wires
should measure between 600 Ohms per foot (1968 Ohms per meter).
- Damaged Or Faulty Ignition Coil-Inspect for cracks, carbon tracking or other damage. Substitute a known good coil with current coil and
retest. If the misfire follows the coil, replace the ignition coil.
- Secondary resistance of coil- Secondary resistance should be between 500-8000 Ohms (5K-8K Ohms).
- If the misfire is random, inspect the following components and conditions:
- System Grounds-Ensure all connections are clean and properly tightened.
- MAF-A Mass Air Flow (MAF) sensor output that causes the PCM to sense a lower than normal air flow will cause a lean condition.
- Air Induction System- Air leaks into the induction system which bypass the MAF sensor will cause a lean condition. Inspect for the
following conditions:
^ Disconnected or damaged vacuum hoses
^ Incorrectly installed or faulty crankcase ventilation valve
^ Vacuum leaks at the throttle body
^ Vacuum leaks at the EGR valve
^ Vacuum leaks at the intake manifold mounting surfaces
- Fuel Pressure-Perform a fuel system pressure test. Inspect for the following conditions that may contribute to a lean condition:
^ A faulty fuel pump
^ A plugged filter
^ A faulty fuel system pressure regulator
- Injectors-Perform injector coil balance test to locate faulty injectors contributing to a lean or flooding condition. In addition to the above
test, inspect the condition of the injector O-rings.
- EGR-Inspect for a leaking valve, adapter, or feed pipes which will contribute to a lean condition or excessive EGR flow.
- Other conditions that may contribute to an engine misfire include the following:
- Incorrect engine oil pressure
- Damaged accessory drive belt or pulley
- Damaged driven accessory
- Damaged generator
- Damaged water pump
- Damaged drive belt tensioner
- Loose or broken motor mounts

IMPORTANT: Remove any debris from the connector surfaces before servicing a component. Inspect the connector gaskets when diagnosing
or replacing a component. Ensure that the gaskets are installed correctly. The gaskets prevent contaminate intrusion.

- Poor terminal connection-Inspect the harness connectors for backed out terminals, improper mating, broken locks, improperly formed or
damaged terminals, and faulty terminal to wire connection. Use a corresponding mating terminal to test for proper tension. Refer to
Diagrams.
- Damaged harness-Inspect the wiring harness for damage. If the harness inspection does not reveal a problem, observe the display on the scan
tool while moving connectors and wiring harnesses related to the sensor. A change in the scan tool display may indicate the location of the
fault. Refer to Diagrams.
- PCM and engine grounds for clean and secure connections

If the DTC is determined to be intermittent, reviewing the Failure Records can be useful in determining when the DTC was last set.

TEST DESCRIPTION
The numbers below refer to the step numbers on the diagnostic table:
2. A malfunctioning injector circuit, crankshaft position system variation not learned condition, or incorrect rough road data from the EBCM
may cause a misfire DTC to be set. If any of the indicated DTCs are set with DTC P0300, diagnose and repair the other DTC before using the
DTC P0300 table.
3. The Misfire Current Cyl # display may normally display a small amount of activity, 0 - 10 counts, but should not steadily increment during
an entire 200 revolution test sample period.
4. Depending on the cause of the misfire, the Misfire History Cyl # counter will display a very large number for the misfiring cylinders. Values
for the non-misfiring cylinders will be less than 1/2 as great as the misfiring cylinders. When investigating a misfire, always start with items
associated with the cylinders that have the largest number of counts stored in the Misfire History Cyl # counter.
5. If the misfiring cylinders are companion cylinders, the condition is most likely linked to the ignition system.
9. Inspect for poor terminal connection, grooves, corrosion, pitting, or loose fit.
17. Inspect for the following conditions that may contribute to the engine misfire, engine oil pressure, damaged accessory drive belt or pulley,
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 330
Chevrolet Venture V6-3.4L VIN E 2010
damaged driven accessory such as, the generator, water pump, drive belt tensioner, etc, or loose or broken motor mounts.

P0301
AllData Editor Note

The manufacturer did not supply a diagnostic chart for this code. To verify that this is a valid code:
1. Check for this code again.
2. If your scantool displays this code again, check freeze frame/misfire monitors for a large number of misfires for cylinder number 1.

If the misfire monitor does NOT show a large number of misfires for this cylinder, the code displayed by your scantool is probably not valid.

If the monitor DOES show a large number of misfires for this cylinder, refer to code P0300 for diagnostics. See: Diagnostic Trouble Code
Tests and Associated Procedures/P Code Charts/P0300

P0302
AllData Editor Note

The manufacturer did not supply a diagnostic chart for this code. To verify that this is a valid code:
1. Check for this code again.
2. If your scantool displays this code again, check freeze frame/misfire monitors for a large number of misfires for cylinder number 2.

If the misfire monitor does NOT show a large number of misfires for this cylinder, the code displayed by your scantool is probably not valid.

If the monitor DOES show a large number of misfires for this cylinder, refer to code P0300 for diagnostics. See: Diagnostic Trouble Code
Tests and Associated Procedures/P Code Charts/P0300

P0303
AllData Editor Note

The manufacturer did not supply a diagnostic chart for this code. To verify that this is a valid code:
1. Check for this code again.
2. If your scantool displays this code again, check freeze frame/misfire monitors for a large number of misfires for cylinder number 3.

If the misfire monitor does NOT show a large number of misfires for this cylinder, the code displayed by your scantool is probably not valid.

If the monitor DOES show a large number of misfires for this cylinder, refer to code P0300 for diagnostics. See: Diagnostic Trouble Code
Tests and Associated Procedures/P Code Charts/P0300

P0304
AllData Editor Note

The manufacturer did not supply a diagnostic chart for this code. To verify that this is a valid code:
1. Check for this code again.
2. If your scantool displays this code again, check freeze frame/misfire monitors for a large number of misfires for cylinder number 4.

If the misfire monitor does NOT show a large number of misfires for this cylinder, the code displayed by your scantool is probably not valid.

If the monitor DOES show a large number of misfires for this cylinder, refer to code P0300 for diagnostics. See: Diagnostic Trouble Code
Tests and Associated Procedures/P Code Charts/P0300

P0305
AllData Editor Note

The manufacturer did not supply a diagnostic chart for this code. To verify that this is a valid code:
1. Check for this code again.
2. If your scantool displays this code again, check freeze frame/misfire monitors for a large number of misfires for cylinder number 5.

If the misfire monitor does NOT show a large number of misfires for this cylinder, the code displayed by your scantool is probably not valid.

If the monitor DOES show a large number of misfires for this cylinder, refer to code P0300 for diagnostics. See: Diagnostic Trouble Code
Tests and Associated Procedures/P Code Charts/P0300

P0306
AllData Editor Note
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 331
Chevrolet Venture V6-3.4L VIN E 2011

The manufacturer did not supply a diagnostic chart for this code. To verify that this is a valid code:
1. Check for this code again.
2. If your scantool displays this code again, check freeze frame/misfire monitors for a large number of misfires for cylinder number 6.

If the misfire monitor does NOT show a large number of misfires for this cylinder, the code displayed by your scantool is probably not valid.

If the monitor DOES show a large number of misfires for this cylinder, refer to code P0300 for diagnostics. See: Diagnostic Trouble Code
Tests and Associated Procedures/P Code Charts/P0300

P0325

Diagnostic Chart
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 332
Chevrolet Venture V6-3.4L VIN E 2012

Schematic

CIRCUIT DESCRIPTION
The Powertrain Control Module (PCM) contains integrated Knock Sensor (KS) diagnostic circuitry. Input signals from the knock sensors are
used to detect engine detonation, allowing the PCM to retard Ignition Control (IC) spark timing based on the amplitude and frequency of the KS
signal being received. The knock sensors produce an AC signal under all engine operating conditions. During engine operation, the PCM
calculates the average voltage of the knock sensor's signal. If the KS system is operating normally, the PCM should monitor KS signal voltages
varying over 0.5 volt above and below the calculated average voltage. If the PCM malfunctions in a manner which will not allow proper
diagnosis of the KS circuits, DTC P0325 will set.

CONDITIONS FOR RUNNING THE DTC


- No TP Sensor, VSS, CKP, MAF, or ECT DTCs are set.
- Engine speed is between 1000 and 5000 RPM.
- Throttle angle is more than 15 percent.
- Engine load is more than45 percent.
- Engine coolant temperature is more than 60°C (153°F).
- Maximum spark retard is less than 15 degrees.
- System voltage is more than 9.0 volts.
- Engine run time is more than 30 seconds.

CONDITIONS FOR SETTING THE DTC


- The PCM detects a malfunction in the integrated knock sensor diagnostic circuitry which will not allow proper diagnosis of the knock sensor
circuits.
- The above condition is present for at least 1 second.

ACTION TAKEN WHEN THE DTC SETS


- The PCM will illuminate the Malfunction Indicator Lamp (MIL) during the second consecutive trip in which the diagnostic test has been run
and failed.
- The PCM will store conditions which were present when the DTC set as Freeze Frame and Failure Records data.
- If the misfire is determined to be catalyst damaging, the PCM will flash the MIL.

CONDITIONS FOR CLEARING THE MIL/DTC


- The PCM will turn OFF the MIL during the third consecutive trip in which the diagnostic has been run and passed.
- The History DTC will clear after 40 consecutive warm-up cycles have occurred without a malfunction.
- The DTC can be cleared by using a scan tool.

DIAGNOSTIC AIDS
Inspect for the following:

IMPORTANT: Remove any debris from the connector surfaces before servicing a component. Inspect the connector gaskets when diagnosing
or replacing a component. Ensure that the gaskets are installed correctly. The gaskets prevent contaminate intrusion.

- Poor terminal connection-Inspect the harness connectors for backed out terminals, improper mating, broken locks, improperly formed or
damaged terminals, and faulty terminal to wire connection. Use a corresponding mating terminal to test for proper tension. Refer to
Diagrams.
- Damaged harness-Inspect the wiring harness for damage. If the harness inspection does not reveal a problem, observe the display on the scan
tool while moving connectors and wiring harnesses related to the sensor. A change in the scan tool display may indicate the location of the
fault. Refer to Diagrams.
- PCM and engine grounds for clean and secure connections

If the DTC is determined to be intermittent, reviewing the Failure Records can be useful in determining when the DTC was last set.
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 333
Chevrolet Venture V6-3.4L VIN E 2013

TEST DESCRIPTION
The numbers below refer to the step numbers on the diagnostic table:
2. This step ensures that the malfunction is present.
3. If sent here from Symptoms, proceed with the diagnostic table.
4. This vehicle is equipped with a PCM which utilizes an Electrically Erasable Programmable Read Only Memory (EEPROM). When the PCM
is being replaced, the new PCM must be programmed.

P0327

Diagnostic Chart
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 334
Chevrolet Venture V6-3.4L VIN E 2014

Schematic

CIRCUIT DESCRIPTION
The Powertrain Control Module (PCM) contains integrated Knock Sensor (KS) diagnostic circuitry. An input signal from the KS is used to
detect engine detonation, allowing the PCM to retard Ignition Control (IC) spark timing based on the amplitude and frequency of the KS signal
being received. The KS produces an AC signal under all engine operating conditions. During engine operation, the PCM calculates the average
voltage of the KS signal. If the knock sensor system is operating normally, the PCM will see KS signal voltage vary above and below the
calculated voltage average. If the PCM detects KS input signal equal to the KS average voltage over 95 percent of a calibrated time, DTC P0327
will set.

CONDITIONS FOR RUNNING THE DTC


- No TP, CMP, CKP, ECT Sensor, or VSS DTCs are set.
- Engine speed is between 1000 and 5000 RPM.
- The engine has been running for a minimum of 30 seconds.
- Throttle angle is more than 15 percent.
- Engine load is more than 45 percent.
- Engine coolant temperature is more than 60°C (140°F).
- Maximum spark retard is less than 15 degrees.
- System voltage is more than 9.0 volts.

CONDITIONS FOR SETTING THE DTC


The PCM detects a KS signal voltage within the calculated average voltage range for at least 10 seconds.

ACTION TAKEN WHEN THE DTC SETS


- The PCM will illuminate the Malfunction Indicator Lamp (MIL) during the second consecutive trip in which the diagnostic test has been run
and failed.
- The PCM will store conditions which were present when the DTC set as Freeze Frame and Failure Records data.
- If the misfire is determined to be catalyst damaging, the PCM will flash the MIL.

CONDITIONS FOR CLEARING THE MIL/DTC


- The PCM will turn OFF the MIL during the third consecutive trip in which the diagnostic has been run and passed.
- The History DTC will clear after 40 consecutive warm-up cycles have occurred without a malfunction.
- The DTC can be cleared by using a scan tool.

DIAGNOSTIC AIDS
Inspect for the following conditions:

IMPORTANT: Remove any debris from the connector surfaces before servicing a component. Inspect the connector gaskets when diagnosing
or replacing a component. Ensure that the gaskets are installed correctly. The gaskets prevent contaminate intrusion.

- Poor terminal connection-Inspect the harness connectors for backed out terminals, improper mating, broken locks, improperly formed or
damaged terminals, and faulty terminal to wire connection. Use a corresponding mating terminal to test for proper tension. Refer to
Diagrams.
- Damaged harness-Inspect the wiring harness for damage. If the harness inspection does not reveal a problem, observe the display on the scan
tool while moving connectors and wiring harnesses related to the sensor. A change in the scan tool display may indicate the location of the
fault. Refer to Diagrams.
- PCM and engine grounds for clean and secure connections

If the DTC is determined to be intermittent, reviewing the Failure Records can be useful in determining when the DTC was last set.

TEST DESCRIPTION
The numbers below refer to the numbers on the diagnostic table:
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 335
Chevrolet Venture V6-3.4L VIN E 2015
2. This step ensures that the malfunction is present.
3. If both the 24X crank sensor and the Cam signal are not present the KS signal will stop updating and may set DTC P0327. The ignition
positive voltage supply and the ground circuits need to be diagnosed using the DTC P0336.
4. If sent here from Symptoms, proceed with the diagnostic table.
P0336

Diagnostic Chart (Part 1 Of 2)


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 336
Chevrolet Venture V6-3.4L VIN E 2016

Diagnostic Chart (Part 2 Of 2)


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 337
Chevrolet Venture V6-3.4L VIN E 2017

Schematic

CIRCUIT DESCRIPTION
The 24X reference signal is used to improve idle spark control at low engine speeds. The Powertrain Control Module (PCM) uses the 24X
reference signal to calculate engine RPM and crankshaft position at engine speeds below 1600 RPM. The PCM constantly monitors the number
of pulses on the 24X reference circuit and compares the number of 24X reference pulses to the number of 3X reference pulses and CAM signal
pulses being received. If the PCM receives an incorrect number of pulses on the 24X reference circuit, DTC P0336 will set and the PCM will use
the 3X reference signal circuit for fuel and ignition control. The engine will continue to start and run using the 3X reference and CAM signals
only.

CONDITIONS FOR RUNNING THE DTC


The engine is running, 3X reference pulses are being received, for a minimum of 3 seconds.

CONDITIONS FOR SETTING THE DTC


The ratio of 24X reference pulses to 3X reference pulses received by the PCM is incorrect.

ACTION TAKEN WHEN THE DTC SETS


- The PCM will illuminate the Malfunction Indicator Lamp (MIL) during the second consecutive trip in which the diagnostic test has been run
and failed.
- The PCM will store conditions which were present when the DTC set as Freeze Frame and Failure Records data.
- If the misfire is determined to be catalyst damaging, the PCM will flash the MIL.

CONDITIONS FOR CLEARING THE MIL/DTC


- The PCM will turn OFF the MIL during the third consecutive trip in which the diagnostic has been run and passed.
- The History DTC will clear after 40 consecutive warm-up cycles have occurred without a malfunction.
- The DTC can be cleared by using a scan tool.

DIAGNOSTIC AIDS
DTC P0336 can be caused by secondary components leaking high voltage into the Ignition Control (IC) module. Inspect for the following
conditions:
- Incorrect harness routing near secondary ignition components.
- Ignition coil arcing to wiring harness or IC module-Check ignition coils for:
- Cracks
- Carbon tracking
- Other signs of damage
- Secondary ignition wires arcing to wiring harness.

IMPORTANT: Remove any debris from the connector surfaces before servicing a component. Inspect the connector gaskets when diagnosing
or replacing a component. Ensure that the gaskets are installed correctly. The gaskets prevent contaminate intrusion.

- Poor terminal connection-Inspect the harness connectors for backed out terminals, improper mating, broken locks, improperly formed or
damaged terminals, and faulty terminal to wire connection. Use a corresponding mating terminal to test for proper tension. Refer to
Diagrams.
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 338
Chevrolet Venture V6-3.4L VIN E 2018
- Damaged harness-Inspect the wiring harness for damage. If the harness inspection does not reveal a problem, observe the display on the scan
tool while moving connectors and wiring harnesses related to the sensor. A change in the scan tool display may indicate the location of the
fault. Refer to Diagrams.
- PCM and engine grounds for clean and secure connections

If the DTC is determined to be intermittent, reviewing the Failure Records can be useful in determining when the DTC was last set.

TEST DESCRIPTION
The numbers below refer to the step numbers on the diagnostic table:
2. If sent here from DTC P0327 proceed with DTC P0336 Diagnostic even if P0336 has not failed this ignition.
8. The 24X RPM on the scan tool should change each time the signal circuit is touched.
9. If the fuse blows in the jumper wire, there is a short to ground on the signal circuit.
13. This vehicle is equipped with a PCM which utilizes an Electrically Erasable Programmable Read Only Memory (EEPROM). When the PCM
is being replaced, the new PCM must be programmed.

P0341

Diagnostic Chart (Part 1 Of 2)


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 339
Chevrolet Venture V6-3.4L VIN E 2019

Diagnostic Chart (Part 2 Of 2)

Schematic
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 340
Chevrolet Venture V6-3.4L VIN E 2020
CIRCUIT DESCRIPTION
During cranking, the Ignition Control (IC) Module monitors the 7X crankshaft position sensor signal. Once the IC Module determines spark
synchronization, 3X reference signals are sent to the Powertrain Control Module (PCM). The PCM will command all six injectors on for one
priming shot of fuel in all cylinders. After the priming, the injectors are left off for the next six fuel control reference signals (two crankshaft
revolutions). This allow each cylinder a chance to use the fuel from the priming shot. During this waiting period, a cam pulse will have been
received by the PCM. The PCM uses the Cam signal pulses to initiate sequential fuel injection. The PCM constantly monitors the number of
pulses on the Cam signal circuit and compares the number of Cam pulses to the number of 24X reference pulses and the number of 3X reference
pulses being received. If the PCM receives an incorrect number of pulses on the Cam reference circuit, DTC P0341 will set and the PCM will
initiate injector sequence without the Cam signal with a one in six chance that injector sequence is correct. The engine will continue to start and
run normally, although the misfire diagnostic will be affected if a misfiring condition occurs.

CONDITIONS FOR RUNNING THE DTC


The engine is running, 3X reference pulses are being received.

CONDITIONS FOR SETTING THE DTC


CMP sensor reference pulse is not detected every engine cycle.

ACTION TAKEN WHEN THE DTC SETS


- The PCM will illuminate the Malfunction Indicator Lamp (MIL) during the second consecutive trip in which the diagnostic test has been run
and failed.
- The PCM will store conditions which were present when the DTC set as Freeze Frame and Failure Records data.
- If the misfire is determined to be catalyst damaging, the PCM will flash the MIL.

CONDITIONS FOR CLEARING THE MIL/DTC


- The PCM will turn OFF the MIL during the third consecutive trip in which the diagnostic has been run and passed.
- The History DTC will clear after 40 consecutive warm-up cycles have occurred without a malfunction.
- The DTC can be cleared by using a scan tool.

DIAGNOSTIC AIDS
DTC P0341 can be caused by secondary components leaking high voltage into the ignition module. Check for the following conditions:
- Incorrect harness routing near secondary ignition components.
- Ignition coil arcing to wiring harness or IC module, check ignition coils for cracks, carbon tracking, or other signs of damage.
- Secondary ignition wires arcing to wiring harness.

IMPORTANT: Remove any debris from the connector surfaces before servicing a component. Inspect the connector gaskets when diagnosing
or replacing a component. Ensure that the gaskets are installed correctly. The gaskets prevent contaminate intrusion.

- Poor terminal connection-Inspect the harness connectors for backed out terminals, improper mating, broken locks, improperly formed or
damaged terminals, and faulty terminal to wire connection. Use a corresponding mating terminal to test for proper tension. Refer to
Diagrams.
- Damaged harness-Inspect the wiring harness for damage. If the harness inspection does not reveal a problem, observe the display on the scan
tool while moving connectors and wiring harnesses related to the sensor. A change in the scan tool display may indicate the location of the
fault. Refer to Diagrams.
- PCM and engine grounds for clean and secure connections

If the DTC is determined to be intermittent, reviewing the Failure Records can be useful in determining when the DTC was last set.

TEST DESCRIPTION
The numbers below refer to the step numbers on the diagnostic table:
8. The Cam Signal on the scan tool should change each time the signal circuit is touched.
9. If the fuse blows in the jumper wire, there is a short to ground on the signal circuit.
16. This vehicle is equipped with a PCM which utilizes an Electrically Erasable Programmable Read Only Memory (EEPROM). When the PCM
is being replaced, the new PCM must be programmed.

P0401
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 341
Chevrolet Venture V6-3.4L VIN E 2021

Diagnostic Chart
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 342
Chevrolet Venture V6-3.4L VIN E 2022

Schematic

CIRCUIT DESCRIPTION
The Powertrain Control Module (PCM) tests the EGR system during deceleration by momentarily commanding the EGR valve to open while
monitoring the Manifold Absolute Pressure (MAP) sensor signal. When the EGR valve is opened, the PCM should see a proportional increase in
MAP. If the expected increase in MAP is not seen, the PCM notes the amount of error that was detected and adjusts an internal fail counter
towards a fail threshold level. When the fail counter exceeds the fail threshold level, the PCM will set DTC P0401. The number of test samples
required to accomplish this may vary according to the amount of detected flow error.

Normally, the PCM will only allow one EGR flow test sample to be taken during an ignition cycle. To aid in verifying a repair, the PCM allows
twelve test samples during the first ignition cycle following a scan tool Clear Info or a battery disconnect. Between nine and twelve samples
should be sufficient for the PCM to determine adequate EGR flow and pass the EGR test.

CONDITIONS FOR RUNNING THE DTC


- No TP, MAP, MAF, ECT, IAT, CKP Sensor, VSS, Injector Circuit, Misfire, Idle Speed, or EGR Pintle Position DTCs set.
- The AC status does not change.
- The transaxle range does not change.
- TP angle is less than 1 percent, deceleration.
- Engine coolant temperature is more than 75°C (167°F).
- Engine speed is between 1000-1400 RPM for Grand Am SE and Alero.
- Engine speed is between 1000-1500 RPM for Grand Am GT.
- IAC position is steady.
- MAP is steady between 15-70 kPa.
- Vehicle speed is more than 37 mph during deceleration.
- BARO sensor more than 70 kPa.
- The vehicle will need to be driven above 50 mph, and then allowed to decelerate. When the vehicle is decelerating while meeting all of the
criteria listed above, the PCM will enable the test to run. As the test is running, you will see the Desired EGR parameter and the Actual EGR
position on the scan tool change from 0 to a calibrated value above 0.

CONDITIONS FOR SETTING THE DTC


MAP changes monitored during EGR flow test indicate insufficient EGR flow.

ACTION TAKEN WHEN THE DTC SETS


- The PCM will illuminate the Malfunction Indicator Lamp (MIL) during the first trip in which the diagnostic test has been run and failed.
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 343
Chevrolet Venture V6-3.4L VIN E 2023
- The PCM will store conditions which were present when the DTC set as Freeze Frame and Failure Records data.

CONDITIONS FOR CLEARING THE MIL/DTC


- The PCM will turn OFF the MIL during the third consecutive trip in which the diagnostic has been run and passed.
- The History DTC will clear after 40 consecutive warm-up cycles have occurred without a malfunction.
- The DTC can be cleared by using a scan tool.

DIAGNOSTIC AIDS
To verify a repair, clear info with the scan tool and run the EGR flow test keeping the following items in mind:
- The PCM will only run the EGR flow test during a gradual deceleration.
- The PCM will only run the EGR test during a closed throttle condition.
- The PCM will only run the EGR test at vehicle speeds above 30 mph.
- Several deceleration cycles will be necessary to run a sufficient number of EGR flow test samples, 9-12.
- The EGR Test Counter displayed on the scan tool can be useful in determining that the EGR flow test is running and to keep track of the
number of test samples taken. The counter will increment each time a test sample is taken.

Inspect for the following conditions:

IMPORTANT: Remove any debris from the connector surfaces before servicing a component. Inspect the connector gaskets when diagnosing
or replacing a component. Ensure that the gaskets are installed correctly. The gaskets prevent contaminate intrusion.

- Poor terminal connection-Inspect the harness connectors for backed out terminals, improper mating, broken locks, improperly formed or
damaged terminals, and faulty terminal to wire connection. Use a corresponding mating terminal to test for proper tension. Refer to
Diagrams.
- Damaged harness-Inspect the wiring harness for damage. If the harness inspection does not reveal a problem, observe the display on the scan
tool while moving connectors and wiring harnesses related to the sensor. A change in the scan tool display may indicate the location of the
fault. Refer to Diagrams.
- PCM and engine grounds for clean and secure connections

If the DTC is determined to be intermittent, reviewing the Failure Records can be useful in determining when the DTC was last set.

P0403
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 344
Chevrolet Venture V6-3.4L VIN E 2024

Diagnostic Chart
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 345
Chevrolet Venture V6-3.4L VIN E 2025

Schematic

CIRCUIT DESCRIPTION
The Powertrain Control Module (PCM) monitors the EGR valve pintle position input to ensure that the valve responds properly to commands
from the PCM. The Linear EGR valve is controlled by using an ignition positive driver and ground circuit within the PCM. The driver has the
ability to detect an electrical malfunction in the ignition positive or ground circuit. If an electrical malfunction occurs, the driver signals the PCM
to set DTC P0403.

CONDITIONS FOR RUNNING THE DTC


- The engine is cranking or running.
- System voltage between 9.0-18.0 volts.

CONDITIONS FOR SETTING THE DTC


- The PCM detects an electrical malfunction in the control circuit for the EGR valve.
- The condition is present for more than 20 seconds.

ACTION TAKEN WHEN THE DTC SETS


- The PCM will illuminate the Malfunction Indicator Lamp (MIL) during the second consecutive trip in which the diagnostic test has been run
and failed.
- The PCM will store conditions which were present when the DTC set as Freeze Frame and Failure Records data.
- If the misfire is determined to be catalyst damaging, the PCM will flash the MIL.

CONDITIONS FOR CLEARING THE MIL/DTC


- The PCM will turn OFF the MIL during the third consecutive trip in which the diagnostic has been run and passed.
- The History DTC will clear after 40 consecutive warm-up cycles have occurred without a malfunction.
- The DTC can be cleared by using a scan tool.

DIAGNOSTIC AIDS
Inspect for the following:

IMPORTANT: Remove any debris from the connector surfaces before servicing a component. Inspect the connector gaskets when diagnosing
or replacing a component. Ensure that the gaskets are installed correctly. The gaskets prevent contaminate intrusion.

- Poor terminal connection-Inspect the harness connectors for backed out terminals, improper mating, broken locks, improperly formed or
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 346
Chevrolet Venture V6-3.4L VIN E 2026
damaged terminals, and faulty terminal to wire connection. Use a corresponding mating terminal to test for proper tension. Refer to
Diagrams.
- Damaged harness-Inspect the wiring harness for damage. If the harness inspection does not reveal a problem, observe the display on the scan
tool while moving connectors and wiring harnesses related to the sensor. A change in the scan tool display may indicate the location of the
fault. Refer to Diagrams.
- PCM and engine grounds for clean and secure connections

If the DTC is determined to be intermittent, reviewing the Failure Records can be useful in determining when the DTC was last set.

TEST DESCRIPTION
The numbers below refer to the step numbers on the diagnostic table:
2. Listen for a click when the solenoid operates. Command the EGR between 0 percent to 10 percent. Repeat the commands as necessary.
3. Verifies that the PCM is providing voltage to the solenoid.
4. Tests for an open in the ground circuit to the solenoid.
5. Tests if voltage is constantly being applied to the solenoid.
12. The PCM utilizes an Electrically Erasable Programmable Read Only Memory (EEPROM). When the PCM is replaced, the new PCM must
be programmed.

P0404
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 347
Chevrolet Venture V6-3.4L VIN E 2027

Diagnostic Chart (Part 1 Of 2)


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 348
Chevrolet Venture V6-3.4L VIN E 2028

Diagnostic Chart (Part 2 Of 2)


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 349
Chevrolet Venture V6-3.4L VIN E 2029

Schematic

CIRCUIT DESCRIPTION
The Powertrain Control Module (PCM) monitors the EGR valve pintle position input to ensure that the valve responds properly to commands
from the PCM. The PCM compares Actual EGR Position with Desired EGR Position when the valve is commanded open. If the difference
between actual EGR position and desired EGR Position is more than 15 percent DTC P0404 will set.

CONDITIONS FOR RUNNING THE DTC


- The ignition is ON.
- System voltage is between 9.0-18.0 volts.

CONDITIONS FOR SETTING THE DTC


- The difference between Actual EGR and Desired EGR Position is more than 15 percent.
- The condition is present for longer than 20 seconds.

ACTION TAKEN WHEN THE DTC SETS


- The PCM will illuminate the Malfunction Indicator Lamp (MIL) during the second consecutive trip in which the diagnostic test has been run
and failed.
- The PCM will store conditions which were present when the DTC set as Freeze Frame and Failure Records data.
- It the misfire is determined to be catalyst damaging, the PCM will flash the MIL.

CONDITIONS FOR CLEARING THE MIL/DTC


- The PCM will turn OFF the MIL during the third consecutive trip in which the diagnostic has been run and passed.
- The History DTC will clear after 40 consecutive warm-up cycles have occurred without a malfunction.
- The DTC can be cleared by using a scan tool.

DIAGNOSTIC AIDS
Inspect for the following conditions:

Excessive deposits on the EGR pintle or seat- Remove the EGR valve and inspect for deposits that may interfere with the EGR valve pintle
extending completely or cause the pintle to stick.

IMPORTANT: Remove any debris from the connector surfaces before servicing a component. Inspect the connector gaskets when diagnosing
or replacing a component. Ensure that the gaskets are installed correctly. The gaskets prevent contaminate intrusion.
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 350
Chevrolet Venture V6-3.4L VIN E 2030

- Poor terminal connection-Inspect the harness connectors for backed out terminals, improper mating, broken locks, improperly formed or
damaged terminals, and faulty terminal to wire connection. Use a corresponding mating terminal to test for proper tension. Refer to
Diagrams.
- Damaged harness-Inspect the wiring harness for damage. If the harness inspection does not reveal a problem, observe the display on the scan
tool while moving connectors and wiring harnesses related to the sensor. A change in the scan tool display may indicate the location of the
fault. Refer to Diagrams.
- PCM and engine grounds for clean and secure connections

If the DTC is determined to be intermittent, reviewing the Failure Records can be useful in determining when the DTC was last set.

TEST DESCRIPTION
Numbers below refer to the step numbers on the Diagnostic Table:
2. Verifies that the malfunction is present.
3. If DTC P0404 will only set under certain conditions, the malfunction may be intermittent, refer to Diagnostic Aids. If an intermittent wiring
problem is not present, check for a poor connection at the PCM or the EGR valve. If the connections are OK and DTC P0404 continues to
set, replace the EGR valve.
16. This vehicle is equipped with a PCM which utilizes an Electrically Erasable Programmable Read Only Memory (EEPROM). When the PCM
is being replaced, the new PCM must be programmed.

P0405
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 351
Chevrolet Venture V6-3.4L VIN E 2031

Diagnostic Chart (Part 1 Of 2)


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 352
Chevrolet Venture V6-3.4L VIN E 2032

Diagnostic Chart (Part 2 Of 2)


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 353
Chevrolet Venture V6-3.4L VIN E 2033

Schematic

CIRCUIT DESCRIPTION
The Powertrain Control Module (PCM) monitors the EGR valve pintle position input to ensure that the valve responds properly to commands
from the PCM and to detect a fault if the pintle position sensor circuit is open or shorted. If the PCM detects an excessively low EGR Feedback
signal voltage, DTC P0405 will set.

CONDITIONS FOR RUNNING THE DTC


System voltage is more than 11 volts.

CONDITIONS FOR SETTING THE DTC


- EGR Feedback is less than 0.30 volt at any time.
- The condition is present for longer than 20 seconds.

ACTION TAKEN WHEN THE DTC SETS


- The PCM will illuminate the Malfunction Indicator Lamp (MIL) during the second consecutive trip in which the diagnostic test has been run
and failed.
- The PCM will store conditions which were present when the DTC set as Freeze Frame and Failure Records data.
- If the misfire is determined to be catalyst damaging, the PCM will flash the MIL.

CONDITIONS FOR CLEARING THE MIL/DTC


- The PCM will turn OFF the MIL during the third consecutive trip in which the diagnostic has been run and passed.
- The History DTC will clear after 40 consecutive warm-up cycles have occurred without a malfunction.
- The DTC can be cleared by using a scan tool.

DIAGNOSTIC AIDS
Inspect for the following conditions:

IMPORTANT: Remove any debris from the connector surfaces before servicing a component. Inspect the connector gaskets when diagnosing
or replacing a component. Ensure that the gaskets are installed correctly. The gaskets prevent contaminate intrusion.

- Poor terminal connection-Inspect the harness connectors for backed out terminals, improper mating, broken locks, improperly formed or
damaged terminals, and faulty terminal to wire connection. Use a corresponding mating terminal to test for proper tension. Refer to
Diagrams.
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 354
Chevrolet Venture V6-3.4L VIN E 2034
- Damaged harness-Inspect the wiring harness for damage. If the harness inspection does not reveal a problem, observe the display on the scan
tool while moving connectors and wiring harnesses related to the sensor. A change in the scan tool display may indicate the location of the
fault. Refer to Diagrams.
- PCM and engine grounds for clean and secure connections

If the DTC is determined to be intermittent, reviewing the Failure Records can be useful in determining when the DTC was last set.

TEST DESCRIPTION
The numbers below refer to the step numbers on the diagnostic table:
2. This step verifies that the malfunction is present.
3. If DTC P0405 only sets under certain conditions, the malfunction may be intermittent. Refer to Diagnostic Aids. If an intermittent wiring
problem is not present, inspect for a faulty connection at the PCM or the EGR valve.
18. This vehicle is equipped with a PCM which utilizes an Electrically Erasable Programmable Read Only Memory (EEPROM). When the PCM
is replaced, the new PCM must be programmed.
P0410
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 355
Chevrolet Venture V6-3.4L VIN E 2035

Diagnostic Chart (Part 1 Of 2)


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 356
Chevrolet Venture V6-3.4L VIN E 2036

Diagnostic Chart (Part 2 Of 2)


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 357
Chevrolet Venture V6-3.4L VIN E 2037

Schematic

CIRCUIT DESCRIPTION
An AIR pump is used on this vehicle to lower tail pipe emissions on start-up. The Powertrain Control Module (PCM) grounds the AIR pump
relay control circuit, which energizes the AIR pump. The PCM also grounds the AIR combination valve vacuum control circuit, which energizes
the AIR vacuum solenoid valve. Vacuum is then applied to both AIR combination valve diaphragms which open the shut off valves.

The PCM enables both circuits simultaneously when AIR system operation is desired. When the AIR system is active, the AIR pump forces fresh
air into the exhaust stream in order to accelerate catalyst operation. The AIR solenoid valves replace the conventional check valves. When the
AIR system is inactive the shut off valves prevent air flow in either direction. DTC P0412 applies to the AIR vacuum control solenoid circuit.
DTC P0418 applies to the AIR pump relay control circuit. DTC P0410 sets if an air flow problem is detected.

The PCM will run up to 3 diagnostic tests using the HO2S 1 voltage to diagnose the AIR system. The first is a passive test, it has 2 parts. The
two parts are the AIR Passive Test 1, and AIR Passive Test 2. The second test is an Active Test, it has one part. This test is named AIR Active
Test.

The AIR Passive/Active Tests consist of the following:

AIR PASSIVE TEST 1


When the AIR system is enabled, the PCM monitors the HO2S 1 voltage for a specific amount of time calculated by the coolant temperature at
start-up. The HO2S 1 is monitored for 10 seconds if the coolant temperature is above 90°C (194°F), or 70 seconds if the coolant temperature is
below 90°C (194°F).
- If the HO2S 1 voltage goes below a calibrated amount, the PCM interprets this as an indication the AIR System is operational and it is
considered a test passed.
- When the AIR Passive Test 1 completes, the PCM then runs the AIR Passive Test 2.

AIR PASSIVE TEST 2


- When the AIR System is disabled, the PCM monitors the HO2S 1 voltage. The HO2S 1 voltage should increase above a calibrated amount
and switch normally.
- When the AIR Passive Test 2 is complete and both AIR Passive tests indicate a pass, no further action is taken. If either one of the above
tests have failed or is inconclusive, the diagnostic will proceed to the AIR Active Test.

AIR ACTIVE TEST


- During this test the PCM turns the AIR system on during Closed Loop operation. When the AIR system is activated, the PCM monitors the
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 358
Chevrolet Venture V6-3.4L VIN E 2038
HO2S voltage. If the AIR system is operating properly, the HO2S 1 voltage should go below a predetermined level.
- The PCM will repeat this test up to 3 consecutive times with a short delay between each command.
- If the PCM determines that the HO2S 1 voltage did not respond as expected during the tests, DTC P0410 will set.

CONDITIONS FOR RUNNING THE DTC


- DTCs P0101, P0102, P0103, P0107, P0108, P0112, P0113, P0117, P0118, P0121, P0122, P0123, P0171, P0172, P0300, P0412, P0418,
P0442, P0443, P1441, and HO2S are not set.
- The engine operates for more than 2 seconds.

CONDITION FOR NOT PASSING AIR ACTIVE TEST


The HO2S 1 voltage changes less than 0.06 or is above 225 mV for 1.5 seconds during 2.5 seconds of AIR pump operation.

CONDITIONS FOR SETTING THE DTC


- The pre-catalyst HO2S voltage remains above 300 mV (Passive) or 150 mV (Active) for a calibrated period of time.
AND
- The Short Term FT does not increase a calibrated amount during the test.
- Both the above conditions exist for 3 consecutive tests.

ACTION TAKEN WHEN THE DTC SETS


- The PCM will illuminate the Malfunction Indicator Lamp (MIL) during the second consecutive trip in which the diagnostic test has been run
and failed.
- The PCM will store conditions which were present when the DTC set as Freeze Frame and Failure Records data.
- If the misfire is determined to be catalyst damaging, the PCM will flash the MIL.

CONDITIONS FOR CLEARING THE MIL/DTC


- The PCM will turn OFF the MIL during the third consecutive trip in which the diagnostic has been run and passed.
- The History DTC will clear after 40 consecutive warm-up cycles have occurred without a malfunction.
- The DTC can be cleared by using a scan tool.

DIAGNOSTIC AIDS
Inspect for the following:

IMPORTANT: Remove any debris from the connector surfaces before servicing a component. Inspect the connector gaskets when diagnosing
or replacing a component. Ensure that the gaskets are installed correctly. The gaskets prevent contaminate intrusion.

- Poor terminal connection-Inspect the harness connectors for backed out terminals, improper mating, broken locks, improperly formed or
damaged terminals, and faulty terminal to wire connection. Use a corresponding mating terminal to test for proper tension. Refer to
Diagrams.
- Damaged harness-Inspect the wiring harness for damage. If the harness inspection does not reveal a problem, observe the display on the scan
tool while moving connectors and wiring harnesses related to the sensor. A change in the scan tool display may indicate the location of the
fault. Refer to Diagrams.
- PCM and engine grounds for clean and secure connections

If the DTC is determined to be intermittent, reviewing the Failure Records can be useful in determining when the DTC was last set.

TEST DESCRIPTION
The numbers below refer to the step numbers on the diagnostic table:
2. DTC P0412 AIR Solenoid Valve Control Circuit and P0418 AIR Pump Relay Control Circuit should be diagnosed first if either are set.
3. Begins testing for a short to ground in the AIR pump feed circuit.
4. Listen for a running motor. Command both the ON and OFF states. Repeat the commands as necessary.
5. Begins testing for a short to voltage in the pump feed circuit.
6. Tests for voltage at the AIR pump relay switch feed circuit.
7. Bypasses the relay.
8. Tests for voltage on the AIR pump feed circuit.
9. Tests for an open on the pump ground circuit.
28. The AIR Pump is not designed to run continuously. If the pump needs to be replaced, check for conditions that may cause continuous pump
operation.

P0412
DTC P0412 Secondary Air Injection (AIR) Solenoid Control Circuit
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 359
Chevrolet Venture V6-3.4L VIN E 2039

Schematic

Circuit Description

An AIR pump is used on this vehicle to lower tail pipe emissions on start-up. The powertrain control module (PCM) grounds the AIR pump relay
control circuit, which energizes the AIR pump. The PCM also grounds the AIR combination valve vacuum control solenoid circuit, which
energizes the AIR vacuum control solenoid. Vacuum is then applied to both AIR combination valve diaphragms which open the shut off valves.
The PCM enables both circuits simultaneously when AIR system operation is desired. When the AIR system is active, the AIR pump forces fresh
air into the exhaust stream in order to accelerate catalyst operation. The AIR combination valves replace the conventional check valves. When
the AIR system is inactive the shut off valves prevent air flow in either direction. DTC P0412 applies to the AIR vacuum control solenoid circuit.
DTC P0418 applies to the AIR pump relay control circuit. DTC P0410 sets if an air flow problem is detected.

The PCM will run up to 3 diagnostic tests using the HO2S 1 voltage to diagnose the AIR system.

AIR Active Test

The AIR Active Test has the PCM turn on the AIR pump specifically for diagnostic purposes. The AIR Active Test consists of the following:

- During this test the PCM turns the AIR system ON during Closed Loop operation. When the AIR system is activated, the PCM monitors the
HO2S voltage. If the AIR system is operating properly, the HO2S 1 voltage should go below a predetermined threshold.
- The PCM will repeat this test up to 3 consecutive times with a short delay between each command.
- If the PCM determines that the HO2S 1 voltage did not respond as expected during the tests, DTC P0410 will set.

Conditions for Running the DTC

- DTCs P0101, P0102, P0103, P0107, P0108, P0112, P0113, P0117, P0118, P0121, P0122, P0123, P0171, P0172, P0300, P0418, P0442,
P0443, P1441, and HO2S are not set.
- The engine operates for more than 2 seconds.

Condition For Not Passing AIR Active Test

The HO2S 1 voltage changes less than .06 or is above 225 mV for 1.8 seconds during 3.0 seconds of AIR pump operation.

Conditions for Setting the DTC


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 360
Chevrolet Venture V6-3.4L VIN E 2040

If the AIR system fails three consecutive tests.

Action Taken When the DTC Sets

- The PCM will illuminate the malfunction indicator lamp (MIL) during the second consecutive trip in which the diagnostic test has been run
and failed.
- The PCM will store conditions which were present when the DTC set as Freeze Frame/Failure Records data.

Conditions for Clearing the MIL/DTC

- The PCM will turn OFF the malfunction indicator lamp (MIL) during the third consecutive trip in which the diagnostic has run and passed.
- The history DTC will clear after 40 consecutive warm-up cycles have occurred without a malfunction.
- The DTC can be cleared by using a scan tool.

Diagnostic Aids

Inspect for the following:

Notice: Do not operate the AIR pump for more than 60 seconds. Continuous operation of the AIR pump in excess of 60 seconds will damage
the AIR pump.

Many situations may lead to an intermittent condition. Perform each inspection or test as directed.

Important: Remove any debris from the connector surfaces before servicing a component. Inspect the connector gaskets when diagnosing or
replacing a component. Ensure that the gaskets are installed correctly. The gaskets prevent contaminate intrusion.

- Loose terminal connection


- Use a corresponding mating terminal to test for proper tension.
- Inspect the harness connectors for backed out terminals, improper mating, broken locks, improperly formed or damaged terminals, and
faulty terminal to wire connection.
- Damaged harness--Inspect the wiring harness for damage. If the harness inspection does not reveal a problem, observe the display on the
scan tool while moving connectors and wiring harnesses related to the sensor. A change in the scan tool display may indicate the location of
the fault. Refer to Wiring Repairs in Wiring Systems for diagnosis and repair.
- Inspect the powertrain control module (PCM) and the engine grounds for clean and secure connections.

If the condition is determined to be intermittent, reviewing the Snapshot or Freeze Frame/Failure Records may be useful in determining when the
DTC or condition was identified.

Test Description

The numbers below refer to the step numbers on the diagnostic table:
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 361
Chevrolet Venture V6-3.4L VIN E 2041

Diagnostic Chart

1. The Powertrain On-Board Diagnostic (OBD) System Check prompts you to complete some basic checks and store the freeze frame and
failure records data on the scan tool.
2. Listen for a click when the solenoid operates. Command both the ON and OFF states. Repeat the commands as necessary.
3. Tests for voltage at the feed side of the solenoid.
4. Verifies that the PCM is providing ground to the solenoid.
5. Tests if ground is constantly being applied to the solenoid.
12. The PCM utilizes an electrically erasable programmable read only memory (EEPROM). When the PCM is replaced, the new PCM must be
programmed.

P0418
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 362
Chevrolet Venture V6-3.4L VIN E 2042

Diagnostic Chart
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 363
Chevrolet Venture V6-3.4L VIN E 2043

Schematic

CIRCUIT DESCRIPTION
Ignition voltage is supplied directly to the AIR Pump relay. The Powertrain Control Module (PCM) controls the relay by grounding the control
circuit via an internal solid state device called a driver. The primary function of the driver is to supply the ground for the component being
controlled. Each driver has a fault line which is monitored by the PCM. When the PCM is commanding a component ON, the voltage of the
control circuit should be low, near 0 volts. When the PCM is commanding the control circuit to a component OFF, the voltage potential of the
circuit should be high, near battery voltage. If the fault detection circuit senses a voltage other than what is expected, this DTC will set.

The PCM will monitor the control circuit for the following:
- A short to ground.
- A short to voltage.
- An open circuit.
- An open relay coil.
- An internally shorted or excessively low resistance relay coil.

When the PCM detects any of the above malfunctions, this DTC will set and the affected driver will be disabled.

CONDITIONS FOR RUNNING THE DTC


- The ignition voltage is between 9.0-18.0 volts.
- The engine speed is more than 80 RPM.
- The PCM driver transitions from ON to OFF or from OFF to ON.

CONDITIONS FOR SETTING THE DTC


- A short to ground, an open circuit, or a short to battery voltage is detected on the control circuit.
- The condition is present for at least 30 seconds.

ACTION TAKEN WHEN THE DTC SETS


- The PCM will illuminate the Malfunction Indicator Lamp (MIL) during the second consecutive trip in which the diagnostic test has been run
and failed.
- The PCM will store conditions which were present when the DTC set as Freeze Frame and Failure Records data.
- If the misfire is determined to be catalyst damaging, the PCM will flash the MIL.

CONDITIONS FOR CLEARING THE MIL/DTC


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 364
Chevrolet Venture V6-3.4L VIN E 2044
- The PCM will turn OFF the MIL during the third consecutive trip in which the diagnostic has been run and passed.
- The History DTC will clear after 40 consecutive warm-up cycles have occurred without a malfunction.
- The DTC can be cleared by using a scan tool.

DIAGNOSTIC AIDS

NOTE: Do not operate the AIR pump for more than 60 seconds. Continuous operation of the AIR pump in excess of 60 seconds will damage
the AIR pump.

Inspect for the following conditions:

IMPORTANT: Remove any debris from the connector surfaces before servicing a component. Inspect the connector gaskets when diagnosing
or replacing a component. Ensure that the gaskets are installed correctly. The gaskets prevent contaminate intrusion.

- Poor terminal connection-Inspect the harness connectors for backed out terminals, improper mating, broken locks, improperly formed or
damaged terminals, and faulty terminal to wire connection. Use a corresponding mating terminal to test for proper tension. Refer to
Diagrams.
- Damaged harness-Inspect the wiring harness for damage. If the harness inspection does not reveal a problem, observe the display on the scan
tool while moving connectors and wiring harnesses related to the sensor. A change in the scan tool display may indicate the location of the
fault. Refer to Diagrams.
- PCM and engine grounds for clean and secure connections

If the DTC is determined to be intermittent, reviewing the Failure Records can be useful in determining when the DTC was last set.

TEST DESCRIPTION
The numbers below refer to the step numbers on the diagnostic table.:
1. The Powertrain On-Board Diagnostic (OBD) System Check prompts you to complete some basic tests and store the freeze frame and failure
records data on the scan tool.
2. Listen for a click when the relay operates. Command both the ON and OFF states. Repeat the commands as necessary.
3. Tests for voltage at the coil feed side of the relay.
4. Verifies that the PCM is providing ground to the relay.
5. Tests if ground is constantly being applied to the relay.
12. The PCM utilizes an Electrically Erasable Programmable Read Only Memory (EEPROM). When the PCM is replaced, the new PCM must
be programmed.

P0420
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 365
Chevrolet Venture V6-3.4L VIN E 2045

Diagnostic Chart (Part 1 Of 2)


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 366
Chevrolet Venture V6-3.4L VIN E 2046

Diagnostic Chart (Part 2 Of 2)

CIRCUIT DESCRIPTION
To control emissions of Hydrocarbons (HC), Carbon Monoxide (CO), and Oxides of Nitrogen (NOx), a three-way catalytic converter is used.
The catalyst within the converter promotes a chemical reaction which oxidizes the HC and CO present in the exhaust gas, convening them into
harmless water vapor and carbon dioxide. The catalyst also reduces NOx, converting it to nitrogen. The converter also has the ability to store
excess oxygen and release the stored oxygen to promote these reactions. This Oxygen Storage Capacity (OSC) is a measurement of the catalyst's
ability to control emissions. The Powertrain Control Module (PCM) monitors this process using a Heated Oxygen Sensor (HO2S) located in the
exhaust stream past the three-way converter. When the catalyst is functioning properly, the HO2S 2 is slow to respond to a large change in the
HO2S 1 signal. When the HO2S 2 responds quickly to a large change in the HO2S 1 signal, the OSC and efficiency of the catalyst is considered
to be bad and the Malfunction Indicator Lamp (MIL) will be illuminated if subsequent tests also indicate a failure.

CONDITIONS FOR RUNNING THE DTC


1. Meet conditions for engine warm up. Use the scan tool catalyst data list in order to verify the following:
- No EGR, ECT, MAF, TP, IAT, MAP, CMP or CKP Sensor, VSS, EVAP, Misfire, HO2S, IAC Valve, Fuel Trim, or Fuel Injector DTCs
set.
- Engine has been running longer than 10 minutes.
- Engine Coolant Temperature (ECT) is between 76°C (169°F)-124°C (255°F).
- BARO is above 75 kPa.
- Vehicle is in Closed Loop.
- Intake Air Temperature (IAT) is above -20°C (-4°F) and less than 100°C (212°F).
- Battery voltage is above 10.7 volts.
2. Warm up the catalyst.
- Fully open hood.
- Transmission is in park, for automatics, or neutral, for manuals.
- Set the parking brake.
- Press and hold the service brake.
- Each time the engine is started the diagnostic can run up to 18 times. After the 10 minute run time, and before the diagnostic runs the
first time, the engine must run an additional 5 minutes between 1500 and 2500 RPM. Any additional tests on the same key cycle, the
engine must be between 1500 and 2500 RPM for 1 minute.
- To activate the diagnostic, return to idle and place the vehicle in drive, depress the clutch pedal for manual.
3. Test the catalyst.
- Transaxle is in drive, for automatics, or neutral for manuals with clutch pedal depressed.
- Within 60 seconds the air fuel ratio will go rich below 14.1 for up to 7 seconds, then may go lean above 15.3 for up to 10 seconds.
- Using the scan tool check and see if DTC P0420 has passed or failed this key cycle.

CONDITIONS FOR SETTING THE DTC


The PCM determines that the catalyst's oxygen storage capacity is below a threshold considered acceptable.

ACTION TAKEN WHEN THE DTC SETS


- The PCM will illuminate the Malfunction Indicator Lamp (MIL) during the first trip in which the diagnostic test has been run and failed.
- The PCM will store conditions which were present when the DTC set as Freeze Frame and Failure Records data.
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 367
Chevrolet Venture V6-3.4L VIN E 2047

CONDITIONS FOR CLEARING THE MIL/DTC


- The PCM will turn OFF the MIL during the third consecutive trip in which the diagnostic has been run and passed.
- The History DTC will clear after 40 consecutive warm-up cycles have occurred without a malfunction.
- The DTC can be cleared by using a scan tool.

DIAGNOSTIC AIDS
Inspect for the following conditions:
- The PCM will not enable the catalyst test until the following conditions are met:
- Engine speed is plus or minus 200 RPM from desired idle.
- Throttle Position (TP) is 1.5 percent or less.
- Short Term FT is between -20-20 percent.
- The catalyst test will abort if the vehicle falls outside the conditions listed below while the test is running:
- Engine speed is plus or minus 200 RPM from desired idle.
- Throttle Position (TP) is 1.5 percent or less.
- Short Term FT is between -20-+20 percent.
- The catalyst test may abort due to a change in engine load. If this problem occurs use the scan tool to force the cooling fans on then return to
Step 3 in the table.

IMPORTANT: When using the scan tool to force the cooling fans on use the next list and previous list soft keys to enter the catalyst data list. If
the catalyst data list is riot entered this way the cooling fan control will be canceled.

- The number of attempted tests is limited to 18 per key cycle.


- More than 6 tests may have to be attempted to get 6 completed tests. An aborted test counts as an attempted test.
- If 18 tests have been attempted, and a decision has not been made this key cycle, then turn the key OFF for 30 seconds, start the vehicle and
perform the Conditions for Running the DTC, including the 10 minute run time.
- After returning to an idle the HO2S 1 signal may stay rich or lean for several seconds causing the test to be delayed.

IMPORTANT: Remove any debris from the connector surfaces before servicing a component. Inspect the connector gaskets when diagnosing
or replacing a component. Ensure that the gaskets are installed correctly. The gaskets prevent contaminate intrusion.

- Poor terminal connection-Inspect the harness connectors for backed out terminals, improper mating, broken locks, improperly formed or
damaged terminals, and faulty terminal to wire connection. Use a corresponding mating terminal to test for proper tension. Refer to
Diagrams.
- Damaged harness-Inspect the wiring harness for damage. If the harness inspection does not reveal a problem, observe the display on the scan
tool while moving connectors and wiring harnesses related to the sensor. A change in the scan tool display may indicate the location of the
fault. Refer to Diagrams.
- PCM and engine grounds for clean and secure connections

If the DTC is determined to be intermittent, reviewing the Failure Records can be useful in determining when the DTC was last set.

TEST DESCRIPTION
Numbers below refer to the step numbers on the Diagnostic Table:
1. The powertrain OBD system check prompts the technician to complete some basic tests and store the Freeze Frame and Failure Records data
on the scan tool if applicable.
2. If any component DTCs are set, diagnose those DTCs first. A fault in a component can cause the converter to appear degraded or may have
caused its failure.
3. Clearing the DTCs allows the catalyst test to be completed up to 6 times this ignition cycle. If the A/C is not turned OFF the diagnostic will
not run. The engine must be warmed-up. The converter needs to be warmed-up by raising the engine speed above idle for the specified time
prior to each attempted test. Observe the if DTC passed or failed this ignition cycle. If the DTC does not pass or fail look for a possible
reason that would cause the test to abort.
4. This step includes checks for conditions that can cause the three-way converter to appear degraded. Repair any problems found before
proceeding with this table.
9. If the three-way converter needs to be replaced, make sure that another condition is not present which could damage the converter. These
conditions may include: misfire, high engine oil or coolant consumption, retarded spark timing or weak spark. Correct any possible causes of
converter damage before replacing the converter.

P0440
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 368
Chevrolet Venture V6-3.4L VIN E 2048

Diagnostic Chart (Part 1 Of 3)


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 369
Chevrolet Venture V6-3.4L VIN E 2049

Diagnostic Chart (Part 2 Of 3)


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 370
Chevrolet Venture V6-3.4L VIN E 2050

Diagnostic Chart (Part 3 Of 3)

Refer to Emission Hose Routing Diagram, EVAP SYSTEM OVERVIEW. See: Emission Control Systems

SYSTEM DESCRIPTION
The EVAP system includes the following components:
- The fuel tank.
- The EVAP canister vent valve.
- The fuel pipes and hoses.
- The fuel fill cap.
- The EVAP vapor pipes.
- The EVAP purge pipes.
- The EVAP canister.
- The EVAP purge valve.

The EVAP LARGE LEAK TEST is based on applying vacuum to the EVAP system and monitoring vacuum decay. The PCM uses the input
from the fuel tank pressure sensor to determine the rate of vacuum decay. At an appropriate time, the PCM turns ON the EVAP canister purge
valve and the EVAP vent valve, causing the purge valve to open and the vent valve to close. This seals the system and allows the engine to draw
a vacuum on the system. At a calibrated time or vacuum level, the PCM turns the purge valve OFF, and tests the system vacuum. If the system is
unable to achieve the calibrated vacuum level, the PCM will set DTC P0440.

The following conditions will set DTC P0440:


- Missing, not completely installed or malfunctioning fuel fill cap.
- Disconnected, damaged, pinched, or blocked EVAP purge line.
- Disconnected or damaged EVAP vent hose.
- Disconnected, damaged, pinched, or blocked fuel tank vapor line.
- A malfunctioning EVAP canister purge valve.
- A malfunctioning EVAP vent valve.
- Open ignition feed circuit to the EVAP vent or purge valve. This should also set DTC P0443 or P0449.
- Damaged EVAP canister.
- A Leaking fuel sender assembly O-ring.
- A Leaking fuel tank or fuel filler neck

CONDITIONS FOR RUNNING THE DTC


- DTC P0443 and P0449 are not active.
- No TP, IAT, FTP, ECT or MAP sensor DTCs set.
- System voltage is between 10 and 18 volts.
- Startup ECT is not more than 4°C - 30°C (39°F - 86°F).
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 371
Chevrolet Venture V6-3.4L VIN E 2051
- Startup ECT is not more than 8°C (14°F) greater than IAT start-up temperature.
- Startup IAT not more than 4°C - 30°C (39°F - 86°F).
- Startup IAT is not more than 3°C (7°F) greater than ECT start-up temperature.
- Fuel tank level is between 15% and 85% for a 0.040-0.060 leak.
- BARO is greater than 75kPa.
- IAT is less than 30°C (86°F).
- VSS below 80 MPH.

CONDITIONS FOR SETTING THE DTC


The EVAP system is not able to achieve or maintain vacuum during the diagnostic test.

ACTION TAKEN WHEN THE DTC SETS


- The PCM will illuminate the Malfunction Indicator Lamp (MIL) during the second consecutive trip in which the diagnostic test has been run
and failed.
- The PCM will store conditions which were present when the DTC set as Freeze Frame and Failure Records data.
- If the misfire is determined to be catalyst damaging, the PCM will flash the MIL.

CONDITIONS FOR CLEARING THE MIL/DTC


- The PCM will turn the MIL OFF during the third consecutive trip in which the diagnostic has been run and passed.
- The history DTC will clear when the PCM turns off the MIL.
- The DTC can be cleared by using a scan tool.

DIAGNOSTIC AIDS
Inspect for the following conditions:
- A malfunctioning or damage EVAP canister.
- A loose, missing, defective or incorrect fuel fill cap.
- Incorrectly routed, kinked, pinched, plugged, or defective EVAP system vacuum and vapor pipes.
- Inspect for charcoal release from the EVAP canister.

IMPORTANT: Remove any debris from the connector surfaces before servicing a component. Inspect the connector gaskets when diagnosing
or replacing a component. Ensure that the gaskets are installed correctly. The gaskets prevent contaminate intrusion.

- Poor terminal connection-Inspect the harness connectors for backed out terminals, improper mating, broken locks, improperly formed or
damaged terminals, and faulty terminal to wire connection. Use a corresponding mating terminal to test for proper tension. Refer to
Diagrams.
- Damaged harness-Inspect the wiring harness for damage. If the harness inspection does not reveal a problem, observe the display on the scan
tool while moving connectors and wiring harnesses related to the sensor. A change in the scan tool display may indicate the location of the
fault. Refer to Diagrams.
- PCM and engine grounds for clean and secure connections

If the DTC is determined to be intermittent, reviewing the Failure Records can be useful in determining when the DTC was last set.

TEST DESCRIPTION
Number(s) below refer to the step number(s) on the Diagnostic Table:
1. The Powertrain On Board Diagnostic (OBD) System Check prompts you to complete some of the basic tests and store the Freeze Frame and
Failure records data on the scan tool if applicable.
4. Verifies the EVAP system is not blocked from the EVAP purge valve to the EVAP canister.
5. Verifies the systems ability only to achieve 1.25 kPa (5 in. H2O), but not the ability to hold vacuum.
11. Tests the ability of the EVAP canister, fresh air hose and EVAP vent valve to hold and maintain vacuum.

P0442
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 372
Chevrolet Venture V6-3.4L VIN E 2052

Diagnostic Chart (Part 1 Of 2)


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 373
Chevrolet Venture V6-3.4L VIN E 2053

Diagnostic Chart (Part 2 Of 2)

Refer to Emission Hose Routing Diagram, EVAP SYSTEM OVERVIEW. See: Emission Control Systems

SYSTEM DESCRIPTION
The EVAP system includes the following components:
- The fuel tank.
- The EVAP vent valve.
- The EVAP canister purge valve.
- The EVAP Canister.
- The fuel pipes and hoses.
- The EVAP vapor and purge pipes.
- The EVAP fresh air vent hose.
- The fuel fill cap.

The EVAP SMALL LEAK TEST is based on applying vacuum to the EVAP system and monitoring vacuum decay. The PCM monitors vacuum
level via the fuel tank pressure sensor input. At an appropriate time, the EVAP canister purge valve and the EVAP vent valve are turned on
allowing engine vacuum to draw a small vacuum on the entire evaporative emission system. After the desired vacuum level has been achieved,
the EVAP purge valve is turned off, sealing the system. A leak is detected by monitoring for a decrease in vacuum level over a given time period,
all other variables remaining constant. A small leak in the system will cause DTC P0442 to be set.

CONDITIONS FOR RUNNING THE DTC


- DTC P0443 or P0449 not active.
- No TP, IAT, FTP, ECT or MAP sensor DTCs set.
- System voltage is between 10 and 18 volts.
- The DTC P0440 diagnostic test has passed.
- Startup ECT is not more than 4°C 30°C (39°F - 86°F).
- Startup ECT is not more than 8°C (14°F) greater than IAT start-up temperature.
- Startup IAT not more than 4°C - 30°C (39°F - 86°F).
- Startup IAT is not more than 3°C (7°F) greater than ECT start-up temperature.
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 374
Chevrolet Venture V6-3.4L VIN E 2054
- Fuel tank level is between 15% and 85% for a 0.040-0.060 leak.
- Fuel tank level is between 30% and 85% for a 0.020 leak..
- BARO is greater than 75kPa.
- IAT is less than 30°C (86°F)
- VSS below 80 MPH.

CONDITIONS FOR SETTING THE DTC


A vacuum decay condition indicating a small leak is detected during the diagnostic test.

ACTION TAKEN WHEN THE DTC SETS


- The PCM will illuminate the Malfunction Indicator Lamp (MIL) during the first trip in which the diagnostic test has been run and failed.
- The PCM will store conditions which were present when the DTC set as Freeze Frame and Failure Records data.

CONDITIONS FOR CLEARING THE MIL/DTC


- The PCM will turn the MIL OFF during the first trip in which the diagnostic has been run and passed.
- The history DTC will clear when the PCM turns off the MIL.
- The DTC can be cleared by using a scan tool.

DIAGNOSTIC AIDS
The following conditions will set DTC P0442:
- Loose or malfunctioning fuel fill cap.
- Damaged EVAP purge or vapor pipes.
- Damaged EVAP fresh air vent hose.
- Malfunctioning EVAP vent valve.
- Damaged EVAP Canister.
- Leaking fuel tank, fuel sender assembly O-ring or pressure relief valve.
- Leaking fuel filler neck or seal.

IMPORTANT: Remove any debris from the connector surfaces before servicing a component. Inspect the connector gaskets when diagnosing
or replacing a component. Ensure that the gaskets are installed correctly. The gaskets prevent contaminate intrusion.

- Poor terminal connection-Inspect the harness connectors for backed out terminals, improper mating, broken locks, improperly formed or
damaged terminals, and faulty terminal to wire connection. Use a corresponding mating terminal to test for proper tension. Refer to
Diagrams.
- Damaged harness-Inspect the wiring harness for damage. If the harness inspection does not reveal a problem, observe the display on the scan
tool while moving connectors and wiring harnesses related to the sensor. A change in the scan tool display may indicate the location of the
fault. Refer to Diagrams.
- PCM and engine grounds for clean and secure connections

If the DTC is determined to be intermittent, reviewing the Failure Records can be useful in determining when the DTC was last set.

TEST DESCRIPTION
Number(s) below refer to the step number(s) on the Diagnostic Table:
1. The powertrain On Board Diagnostic (OBD) System Check prompts you to complete some of the basic tests and store the Freeze Frame and
Failure Records data on the scan tool if applicable.
15. The EVAP station is pressurizing a sensor that normally reads vacuum. The scan tool reads high pressure at 0 volts and high vacuum at 5
volts. The scan tool can only read a max pressure of 6.0 inches of H2O (0 Volts), however the EVAP service station can pressurize the
system to much higher pressures. The scan tool value should be within 0.5 in. H2O of the specified value.

P0443
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 375
Chevrolet Venture V6-3.4L VIN E 2055

Diagnostic Chart
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 376
Chevrolet Venture V6-3.4L VIN E 2056

Schematic

CIRCUIT DESCRIPTION
Output Driver Modules (ODMs) are used by the Powertrain Control Module (PCM) in order to turn On many of the current-driven devices that
are needed to control various engine and transmission functions. Each ODM is capable of controlling up to 7 separate outputs by applying
ground to the device which the PCM is commanding On. ODMs have the capability of diagnosing each output circuit individually. DTC P0443
indicates an improper voltage level has been detected on the output circuit which controls the EVAP canister purge solenoid valve.

CONDITIONS FOR RUNNING THE DTC


- The ignition is ON.
- System voltage between 9.0 and 18.0 volts.

CONDITIONS FOR SETTING THE DTC


- An improper voltage level has been detected on the output circuit which controls the EVAP canister purge solenoid valve.
- The above conditions are present for at least 30 seconds.

ACTION TAKEN WHEN THE DTC SETS


- The PCM illuminates the Malfunction Indicator Lamp (MIL) during the second consecutive trip in which the diagnostic test has run and
failed.
- The PCM stores the conditions which were present when the DTC set as Freeze Frame and Fail Records data.

CONDITIONS FOR CLEARING THE MIL/DTC


- The PCM turns the MIL OFF during the third consecutive trip in which the diagnostic has run and passed.
- The history DTC clears after 40 consecutive warm-up cycles have occurred without a malfunction.
- The DTC can be cleared by using the scan tool Clear Information function or by disconnecting the PCM battery feed.

DIAGNOSTIC AIDS
Inspect for the following conditions:

IMPORTANT: Remove any debris from the connector surfaces before servicing a component. Inspect the connector gaskets when diagnosing
or replacing a component. Ensure that the gaskets are installed correctly. The gaskets prevent contaminate intrusion.

- Poor terminal connection-Inspect the harness connectors for backed out terminals, improper mating, broken locks, improperly formed or
damaged terminals, and faulty terminal to wire connection. Use a corresponding mating terminal to test for proper tension. Refer to
Diagrams.
- Damaged harness-Inspect the wiring harness for damage. If the harness inspection does not reveal a problem, observe the display on the scan
tool while moving connectors and wiring harnesses related to the sensor. A change in the scan tool display may indicate the location of the
fault. Refer to Diagrams.
- PCM and engine grounds for clean and secure connections

If the DTC is determined to be intermittent, reviewing the Failure Records can be useful in determining when the DTC was last set.

TEST DESCRIPTION
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 377
Chevrolet Venture V6-3.4L VIN E 2057
The numbers below refer to the step numbers on the diagnostic table:
1. The powertrain OBD System Check prompts you to complete some basic tests and store the Freeze Frame and Failure Records data on the
scan tool.
2. Listen for an audible clicking when the purge solenoid operates. Command both the Increase and Decrease states. Repeat the commands as
necessary.
3. Tests for voltage at the feed side of the solenoid.
4. Verifies that the PCM is providing ground to the solenoid.
5. Tests if ground is constantly being applied to the solenoid.
12. The PCM utilizes an Electrically Erasable Programmable Read Only Memory (EEPROM). When the PCM is replaced, the new PCM must
be programmed.

P0446

Diagnostic Chart (Part 1 Of 2)


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 378
Chevrolet Venture V6-3.4L VIN E 2058

Diagnostic Chart (Part 2 Of 2)

Refer to Emission Hose Routing Diagram, EVAP SYSTEM OVERVIEW. See: Emission Control Systems

SYSTEM DESCRIPTION
The EVAP system includes the following components:
- The fuel tank.
- The EVAP vent valve.
- The fuel pipes and hoses.
- The fuel fill cap.
- The EVAP vapor pipes.
- The EVAP purge pipes.
- The EVAP canister.
- The EVAP canister purge valve.

A RESTRICTED or BLOCKED EVAP VENT PATH is detected by monitoring fuel tank pressure during normal operation (EVAP vent valve
open, EVAP canister purge valve normal). With the EVAP vent valve open, vacuum level in the system should be very low unless the vent path
is blocked.

The following conditions will set DTC P0446.


- Faulty EVAP vent valve (stuck closed).
- Plugged kinked or pinched vent hose.
- Shorted EVAP vent valve driver circuit.
- Plugged EVAP canister.

CONDITIONS FOR RUNNING THE DTC


All conditions for P0440 and P0442 have been met and passed.

CONDITIONS FOR SETTING THE DTC


- Fuel tank pressure is less than -10 in. H2O.
- The condition is present for up to 30 seconds.

ACTION TAKEN WHEN THE DTC SETS


- The PCM will illuminate the Malfunction Indicator Lamp (MIL) during the second consecutive trip in which the diagnostic test has been run
and failed.
- The PCM will store conditions which were present when the DTC set as Freeze Frame and Failure Records data.
- If the misfire is determined to be catalyst damaging, the PCM will flash the MIL.

CONDITIONS FOR CLEARING THE MIL/DTC


- The PCM will turn the MIL OFF during the third consecutive trip in witch the diagnostic has been run and passed.
- The history DTC will clear when the PCM turns OFF the MIL.
- The DTC can be cleared by using the scan tool.

DIAGNOSTIC AIDS
Inspect for the following conditions:
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 379
Chevrolet Venture V6-3.4L VIN E 2059
- Kinked, pinched or plugged vent hose.
- Inspect for charcoal release from the EVAP canister.

IMPORTANT: Remove any debris from the connector surfaces before servicing a component. Inspect the connector gaskets when diagnosing
or replacing a component. Ensure that the gaskets are installed correctly. The gaskets prevent contaminate intrusion.

- Poor terminal connection-Inspect the harness connectors for backed out terminals, improper mating, broken locks, improperly formed or
damaged terminals, and faulty terminal to wire connection. Use a corresponding mating terminal to test for proper tension. Refer to
Diagrams.
- Damaged harness-Inspect the wiring harness for damage. If the harness inspection does not reveal a problem, observe the display on the scan
tool while moving connectors and wiring harnesses related to the sensor. A change in the scan tool display may indicate the location of the
fault. Refer to Diagrams.
- PCM and engine grounds for clean and secure connections

If the DTC is determined to be intermittent, reviewing the Failure Records can be useful in determining when the DTC was last set.

TEST DESCRIPTION
Number(s) below refer to the step number(s) on the Diagnostic Table:
1. The Powertrain On Board Diagnosis (OBD) System Check prompts you to the basic tests and store the Freeze Frame and Failure Records
Data on the scan tool if applicable.
5. Tests the EVAP canister purge valve for a small vacuum source during non purge.
7. Tests the EVAP vent valve for a restriction or blockage.

P0449
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 380
Chevrolet Venture V6-3.4L VIN E 2060

Diagnostic Chart
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 381
Chevrolet Venture V6-3.4L VIN E 2061

Schematic

CIRCUIT DESCRIPTION
Output Driver Modules (ODMs) are used by the Powertrain Control Module (PCM) in order to turn ON many of the current-driven devices that
are needed to control various engine and transmission functions. Each ODM is capable of controlling up to 7 separate outputs by applying
ground to the device which the PCM is commanding ON. Unlike the Quad Driver Modules (QDMs) used in prior model years, ODMs have the
capability of diagnosing each output circuit individually. DTC P0449 set indicates an improper voltage level has been detected on the output
circuit which controls the EVAP canister vent solenoid valve.

CONDITIONS FOR RUNNING THE DTC


The ignition is ON.

CONDITIONS FOR SETTING THE DTC


- An improper voltage level has been detected on the output circuit which controls the Evaporative Emissions System (EVAP) canister vent
solenoid valve.
- The above conditions are present for at least 30 seconds.

ACTION TAKEN WHEN THE DTC SETS


- The PCM illuminates the Malfunction Indicator Lamp (MIL) during the second consecutive trip in which the diagnostic test has run and
failed.
- The PCM stores the conditions which were present when the DTC set as Freeze Frame and Fail Records data.

CONDITIONS FOR CLEARING THE MIL/DTC


- The PCM turns the MIL OFF during the third consecutive trip in which the diagnostic has been run and passed.
- The history DTC clears after 40 consecutive warm-up cycles have occurred without a malfunction.
- The DTC can be cleared by using the scan tool Clear Info function or by disconnecting the PCM battery feed.

DIAGNOSTIC AIDS
Inspect for the following conditions:

IMPORTANT: Remove any debris from the connector surfaces before servicing a component. Inspect the connector gaskets when diagnosing
or replacing a component. Ensure that the gaskets are installed correctly. The gaskets prevent contaminate intrusion.

- Poor terminal connection-Inspect the harness connectors for backed out terminals, improper mating, broken locks, improperly formed or
damaged terminals, and faulty terminal to wire connection. Use a corresponding mating terminal to test for proper tension. Refer to
Diagrams.
- Damaged harness-Inspect the wiring harness for damage. If the harness inspection does not reveal a problem, observe the display on the scan
tool while moving connectors and wiring harnesses related to the sensor. A change in the scan tool display may indicate the location of the
fault. Refer to Diagrams.
- PCM and engine grounds for clean and secure connections

If the DTC is determined to be intermittent, reviewing the Failure Records can be useful in determining when the DTC was last set.
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 382
Chevrolet Venture V6-3.4L VIN E 2062

TEST DESCRIPTION
The numbers below refer to the step numbers on the diagnostic table.
1. The Powertrain OBD System Check prompts you to complete some basic checks and store the Freeze Frame and Failure Records data on the
scan tool.
2. Listen for an audible click when the Vent solenoid operates. Command both the ON and OFF states. Repeat the commands as necessary.
3. Tests for voltage at the feed side of the solenoid.
4. Verifies that the PCM is providing ground to the solenoid.
5. Tests if ground is constantly being applied to the solenoid.
12. The PCM utilizes an Electrically Erasable Programmable Read Only Memory (EEPROM). When the PCM is replaced, the new PCM must
be programmed.

P0452

Diagnostic Chart (Part 1 Of 2)


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 383
Chevrolet Venture V6-3.4L VIN E 2063

Diagnostic Chart (Part 2 Of 2)


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 384
Chevrolet Venture V6-3.4L VIN E 2064

Schematic

CIRCUIT DESCRIPTION
The PCM monitors the fuel tank pressure sensor signal to detect vacuum decay and excess vacuum during the enhanced EVAP diagnostic. The
fuel tank pressure sensor measures the difference between the air pressure (or vacuum) in the tank and the outside air pressure. The PCM applies
a 5.0 volt reference and ground to the sensor. The sensor will return a signal voltage between 0.1 and 4.9 volts. If the PCM detects a fuel tank
pressure sensor signal that is excessively low, DTC P0452 will set.

CONDITIONS FOR RUNNING THE DTC


- System voltage between 10.0 and 18.0 volts.
- The ignition is on.

CONDITIONS FOR SETTING THE DTC


- The fuel tank pressure sensor signal is less than 0.5 volts.
- The conditions is present for 5 second.

ACTION TAKEN WHEN THE DTC SETS


- The PCM will illuminate the Malfunction Indicator Lamp (MIL) during the second consecutive trip in which the diagnostic test has been run
and failed.
- The PCM will store conditions which were present when the DTC set as Freeze Frame and Failure Records data.
- If the misfire is determined to be catalyst damaging, the PCM will flash the MIL.

CONDITIONS FOR CLEARING THE MIL/DTC


The PCM will turn OFF the MIL during the third consecutive trip in which the diagnostic has been run and passed.
- The History DTC will clear after 40 consecutive warm-up cycles have occurred without a malfunction.
- The DTC can be cleared by using a scan tool.

DIAGNOSTIC AIDS
Check for the following condition(s):
- Poor connection at the PCM or Fuel Tank Pressure Sensor.
Inspect harness connectors for backed out terminals, improper mating broken locks, improperly formed or damaged terminals, and poor
terminal to wire connection.
- Damaged harness.
Inspect the wiring harness for damage. If the harness appears to be OK, observe the Fuel Tank Pressure Sensor display on the scan tool while
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 385
Chevrolet Venture V6-3.4L VIN E 2065
moving connectors and wiring related to the sensor. A change in the display will indicate the location of the malfunction.

TEST DESCRIPTION
Numbers below refer to the step numbers on the Diagnostic Table:
12. This vehicle is equipped with a PCM which utilizes an Electrically Erasable Programmable Read Only Memory (EEPROM). When the PCM
is being replaced, the new PCM must be programmed.

P0453

Diagnostic Chart
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 386
Chevrolet Venture V6-3.4L VIN E 2066

Schematic

CIRCUIT DESCRIPTION
The PCM monitors the fuel tank pressure sensor signal to detect vacuum decay and excess vacuum during the enhanced EVAP diagnostic. The
fuel tank pressure sensor measures the difference between the air pressure (or vacuum) in the tank and the outside air pressure. The PCM applies
a 5.0 volt reference and ground to the sensor. The sensor will return a signal voltage between 0.1 and 4.9 volts. If the PCM detects a fuel tank
pressure sensor signal that is excessively high, DTC P0453 will set.

CONDITIONS FOR RUNNING THE DTC


- System voltage is between 10.0 and 18.0 volts.
- The ignition is on.

CONDITIONS FOR SETTING THE DTC


- The fuel tank pressure sensor signal is greater than 4.9 volts.
- The conditions is present for 5 seconds.

ACTION TAKEN WHEN THE DTC SETS


- The PCM will illuminate the Malfunction Indicator Lamp (MIL) during the second consecutive trip in which the diagnostic test has been run
and failed.
- The PCM will store conditions which were present when the DTC set as Freeze Frame and Failure Records data.
- If the misfire is determined to be catalyst damaging, the PCM will flash the MIL.

CONDITIONS FOR CLEARING THE MIL/DTC


- The PCM will turn OFF the MIL during the third consecutive trip in which the diagnostic has been run and passed.
- The History DTC will clear after 40 consecutive warm-up cycles have occurred without a malfunction.
- The DTC can be cleared by using a scan tool.

DIAGNOSTIC AIDS
Check for the following condition(s):
- Poor connection at the PCM or Fuel Tank Pressure Sensor.
Inspect harness connectors for backed out terminals, improper mating broken locks, improperly formed or damaged terminals, and poor
terminal to wire connection.
- Damaged harness.
Inspect the wiring harness for damage. If the harness appears to be OK, observe the Fuel Tank Pressure Sensor display on the scan tool while
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 387
Chevrolet Venture V6-3.4L VIN E 2067
moving connectors and wiring related to the sensor. A change in the display will indicate the location of the malfunction.

TEST DESCRIPTION
Numbers below refer to the step numbers on the Diagnostic Table:
10. This vehicle is equipped with a PCM which utilizes an Electrically Erasable Programmable Read Only Memory (EEPROM). When the PCM
is being replaced, the new PCM must be programmed.

P0462

Diagnostic Chart
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 388
Chevrolet Venture V6-3.4L VIN E 2068
Schematic

CIRCUIT DESCRIPTION
The PCM uses the fuel level input in order to calculate the expected vapor pressures within the fuel system. These vapor pressures vary as the
fuel level changes. The vapor pressure is critical in determining if the Evaporative Emissions System is operating properly. The PCM also uses
the fuel level in order to determine if the fuel level is too high or too low to be able to accurately detect EVAP system malfunction.

CONDITIONS FOR RUNNING THE DTC


- The ignition is ON.
- System is between 10.0 and 18.0 volts.

CONDITIONS FOR SETTING THE DTC


The Fuel Level Sensor should be less than 3% for greater than 10 seconds.

ACTION TAKEN WHEN THE DTC SETS


- The PCM will not illuminate the Malfunction Indicator Lamp (MIL).
- The PCM will store conditions which were present when the DTC set as Failure Records data only. This information will not be stored as
Freeze Frame data.

CONDITIONS FOR CLEARING THE MIL/DTC


- A History DTC will clear after 40 consecutive warm-up cycles have occurred without a malfunction.
- The DTC can be cleared by using a scan tool.

DIAGNOSTIC AIDS
- An intermittent problem may be caused by the following conditions:
- Poor electrical connection
- Rubbed through wire insulation
- A wire that is broken inside the wire insulation
- Any circuitry, that is suspected as causing the intermittent complaint, should be thoroughly checked for the following conditions:
- Backed out terminals
- Improper mating
- Broken locks
- Improperly formed or damaged terminals
- Poor terminal to wire connection

IMPORTANT: Remove any debris from the connector surfaces before servicing a component. Inspect the connector gaskets when diagnosing
or replacing a component. Ensure that the gaskets are installed correctly. The gaskets prevent contaminate intrusion.

- Poor terminal connection-Inspect the harness connectors for backed out terminals, improper mating, broken locks, improperly formed or
damaged terminals, and faulty terminal to wire connection. Use a corresponding mating terminal to test for proper tension. Refer to
Diagrams.
- Damaged harness-Inspect the wiring harness for damage. If the harness inspection does not reveal a problem, observe the display on the scan
tool while moving connectors and wiring harnesses related to the sensor. A change in the scan tool display may indicate the location of the
fault. Refer to Diagrams.
- PCM and engine grounds for clean and secure connections

If the DTC is determined to be intermittent, reviewing the Failure Records can be useful in determining when the DTC was last set.

TEST DESCRIPTION
Number(s) below refer to the step number(s) on the Diagnostic Table.
1. The Powertrain OBD System Check prompts the technician to complete some basic checks and store the freeze frame and failure records data
or the scan tool if applicable. This creates an electronic copy of the data taken when the malfunction occurred. The information is then stored
in the scan tool for later reference.
3. Tests for the proper operation of the fuel level circuit in the low voltage range.

P0463
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 389
Chevrolet Venture V6-3.4L VIN E 2069

Diagnostic Chart
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 390
Chevrolet Venture V6-3.4L VIN E 2070

Schematic

CIRCUIT DESCRIPTION
The PCM uses the fuel level input in order to calculate the expected vapor pressures within the fuel system. These vapor pressures vary as the
fuel level changes. The vapor pressure is critical in determining if the Evaporative Emissions System is operating properly. The PCM also uses
the fuel level in order to determine if the fuel level is too high or too low to be able to accurately detect EVAP system malfunction.

CONDITIONS FOR RUNNING THE DTC


- The ignition is ON.
- System voltage is between 10.0 and 18.0 volts.

CONDITIONS FOR SETTING THE DTC


The Fuel Level Sensor should be greater than 98% for greater than 25 seconds.

ACTION TAKEN WHEN THE DTC SETS


- The PCM will not illuminate the Malfunction Indicator Lamp (MIL).
- The PCM will store conditions which were present when the DTC set as Failure Records data only. This information will not be stored as
Freeze Frame data.

CONDITIONS FOR CLEARING THE MIL/DTC


- A History DTC will clear after 40 consecutive warm-up cycles have occurred without a malfunction.
- The DTC can be cleared by using a scan tool.

DIAGNOSTIC AIDS
- An intermittent problem may be caused by the following conditions:
- Poor electrical connection
- Rubbed through wire insulation
- A wire that is broken inside the wire insulation
- Any circuitry, that is suspected as causing the intermittent complaint, should be thoroughly checked for the following conditions:
- Backed out terminals
- Improper mating
- Broken locks
- Improperly formed or damaged terminals
- Poor terminal to wire connection

IMPORTANT: Remove any debris from the connector surfaces before servicing a component. Inspect the connector gaskets when diagnosing
or replacing a component. Ensure that the gaskets are installed correctly. The gaskets prevent contaminate intrusion.

- Poor terminal connection-Inspect the harness connectors for backed out terminals, improper mating, broken locks, improperly formed or
damaged terminals, and faulty terminal to wire connection. Use a corresponding mating terminal to test for proper tension. Refer to
Diagrams.
- Damaged harness-Inspect the wiring harness for damage. If the harness inspection does not reveal a problem, observe the display on the scan
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 391
Chevrolet Venture V6-3.4L VIN E 2071
tool while moving connectors and wiring harnesses related to the sensor. A change in the scan tool display may indicate the location of the
fault. Refer to Diagrams.
- PCM and engine grounds for clean and secure connections

If the DTC is determined to be intermittent, reviewing the Failure Records can be useful in determining when the DTC was last set.

TEST DESCRIPTION
Number(s) below refer to the step number(s) on the Diagnostic Table:
1. The Powertrain OBD System Check prompts the technician to complete some basic checks and store the freeze frame and failure records data
on the scan tool if applicable. This creates an electronic copy of the data taken when the malfunction occurred. The information is then stored
in the scan tool for later reference.
2. Tests for proper operation of the fuel level circuit in the high voltage range.
3. Tests for proper operation of the fuel level circuit in the low voltage range. If the fuse in the jumper opens when you perform this test, the
signal is sorted to voltage.
9. Replacement PCM must be reprogrammed and the crankshaft position system variation procedure must be performed. Refer to the latest
Techline information for PCM reprogramming and also refer to the CKP System Variation Learn Procedure for the Crankshaft Position
System Variation Procedure.

P0480
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 392
Chevrolet Venture V6-3.4L VIN E 2072

Diagnostic Chart

Refer to Engine Controls Schematics. See: Diagrams/Electrical Diagrams

CIRCUIT DESCRIPTION
Output Driver Modules (ODMs) are used by the PCM to turn ON many of the current-driven devices that are needed to control various engine
and Transaxle functions. Each ODM is capable of controlling up to 7 separate outputs by applying ground to the device which the PCM is
commanding ON. ODMs have the capability of diagnosing each output circuit individually. DTC P0480 set indicates an improper voltage level
has been detected on the output circuit which controls the Fan 1 Relay.

CONDITIONS FOR RUNNING THE DTC


The ignition is ON.

CONDITIONS FOR SETTING THE DTC


- An improper voltage level has been detected on the output circuit which controls the low speed fans.
- The above conditions present for at least 30 seconds.

ACTION TAKEN WHEN THE DTC SETS


- The PCM will illuminate the Malfunction Indicator Lamp (MIL) during the second consecutive trip in which the diagnostic test has been run
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 393
Chevrolet Venture V6-3.4L VIN E 2073
and tailed.
- The PCM will store conditions which were present when the DTC set as Freeze Frame and Failure Records data.
- If the misfire is determined to be catalyst damaging, the PCM will flash the MIL.

CONDITIONS FOR CLEARING THE MIL/DTC


- The PCM will turn OFF the MIL during the third consecutive trip in which the diagnostic has been run and passed.
- The History DTC will clear after 40 consecutive warm-up cycles have occurred without a malfunction.
- The DTC can be cleared by using a scan tool.

DIAGNOSTIC AIDS
Inspect for the following:

IMPORTANT: Remove any debris from the connector surfaces before servicing a component. Inspect the connector gaskets when diagnosing
or replacing a component. Ensure that the gaskets are installed correctly. The gaskets prevent contaminate intrusion.

- Poor terminal connection-Inspect the harness connectors for backed out terminals, improper mating, broken locks, improperly formed or
damaged terminals, and faulty terminal to wire connection. Use a corresponding mating terminal to test for proper tension. Refer to
Diagrams.
- Damaged harness-Inspect the wiring harness for damage. If the harness inspection does not reveal a problem, observe the display on the scan
tool while moving connectors and wiring harnesses related to the sensor. A change in the scan tool display may indicate the location of the
fault. Refer to Diagrams.
- PCM and engine grounds for clean and secure connections

If the DTC is determined to be intermittent, reviewing the Failure Records can be useful in determining when the DTC was last set.

TEST DESCRIPTION
The numbers below refer to the step numbers on the diagnostic table:
1. The powertrain OBD System Check prompts you to complete some basic tests and store the Failure Records data on the scan tool.
2. Listen for an audible click when the relay operates. Command both the ON and OFF states. Repeat the commands as necessary.
3. Tests for voltage at the coil feed side of the relay.
4. Verifies that the PCM is providing ground to the relay.
5. Tests if ground is constantly being applied to the relay.
12. The PCM utilizes an electrically erasable programmable read only memory (EEPROM). When the PCM is replaced, the new PCM must be
programmed.

P0481
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 394
Chevrolet Venture V6-3.4L VIN E 2074

Diagnostic Chart

Refer to Engine Controls Schematics. See: Diagrams/Electrical Diagrams

CIRCUIT DESCRIPTION
Output Driver Modules (ODMs) are used by the PCM to turn on many of the current-driven devices that are needed to control various engine
and transaxle functions. Each ODM is capable of controlling up to 7 separate outputs by applying ground to the device which the PCM is
commanding ON. Unlike the Quad Driver Modules (QDMs) used in prior model years, ODMs have the capability of diagnosing each output
circuit individually. DTC P1652 set indicates an improper voltage level has been detected on ODM B output 2, which controls the high speed
and series/parallel cooling fan relays.

CONDITIONS FOR RUNNING THE DTC


The ignition is ON.

CONDITIONS FOR SETTING THE DTC


- An improper voltage level has been detected on the output circuit which controls the high speed fans.
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 395
Chevrolet Venture V6-3.4L VIN E 2075
- The above conditions are present for at least 30 seconds.

ACTION TAKEN WHEN THE DTC SETS


- The PCM will illuminate the Malfunction Indicator Lamp (MIL) during the second consecutive trip in which the diagnostic test has been run
and failed.
- The PCM will store conditions which were present when the DTC set as Freeze Frame and Failure Records data.
- If the misfire is determined to be catalyst damaging, the PCM will flash the MIL.

CONDITIONS FOR CLEARING THE MIL/DTC


- The PCM will turn OFF the MIL during the third consecutive trip in which the diagnostic has been run and passed.
- The History DTC will clear after 40 consecutive warm-up cycles have occurred without a malfunction.
- The DTC can be cleared by using a scan tool.

DIAGNOSTIC AIDS
Inspect for the following:

IMPORTANT: Remove any debris from the connector surfaces before servicing a component. Inspect the connector gaskets when diagnosing
or replacing a component. Ensure that the gaskets are installed correctly. The gaskets prevent contaminate intrusion.

- Poor terminal connection-Inspect the harness connectors for backed out terminals, improper mating, broken locks, improperly formed or
damaged terminals, and faulty terminal to wire connection. Use a corresponding mating terminal to test for proper tension. Refer to
Diagrams.
- Damaged harness-Inspect the wiring harness for damage. If the harness inspection does not reveal a problem, observe the display on the scan
tool while moving connectors and wiring harnesses related to the sensor. A change in the scan tool display may indicate the location of the
fault. Refer to Diagrams.
- PCM and engine grounds for clean and secure connections

If the DTC is determined to be intermittent, reviewing the Failure Records can be useful in determining when the DTC was last set.

TEST DESCRIPTION
The numbers below refer to the step numbers on the diagnostic table:
1. The Powertrain OBD System Check prompts you to complete some basic tests and store the Failure Records data on the scan tool.
2. Listen for an audible click when the relay operates. Command both the ON and OFF states. Repeat the commands as necessary.
3. Tests for voltage at the coil feed side of the relays.
4. Verifies that the PCM is providing ground to the relays.
5. Tests if ground is constantly being applied to the relays.
12. The PCM utilizes an Electrically Erasable Programmable Read Only Memory (EEPROM). When the PCM is replaced, the new PCM must
be programmed.

P0502
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 396
Chevrolet Venture V6-3.4L VIN E 2076

Diagnostic Chart 1 Of 2
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 397
Chevrolet Venture V6-3.4L VIN E 2077

Diagnostic Chart 2 Of 2
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 398
Chevrolet Venture V6-3.4L VIN E 2078

Schematic

Circuit Description with 4T65-E Automatic Transaxle


The Vehicle Speed Sensor (VSS) system is a pulse generator consisting of a speed sensor assembly, located in the case extension, and a toothed
vehicle speed sensor reluctor wheel, which is pressed onto the final drive carrier assembly. As the vehicle drives forward, the vehicle speed
sensor reluctor wheel rotates. This rotation produces a variable AC signal in the pickup coil that is proportional to vehicle speed.

The AC signal generated has a frequency and amplitude (voltage). The PCM uses the frequency to calculate the vehicle speed. The voltage
portion of the signal is used for diagnostic purposes only. The voltage will vary from 0.5 volts AC at 100 RPM to as much as 200 volts AC at
6000 RPM.

This information is then sent to the PCM to indicate how fast the vehicle is traveling and to develop the shift pattern for the transmission. Other
systems also use VSS information:
^ TCC apply and release
^ Cruise control system
^ Fuel delivery systems

If the PCM detects a low vehicle speed with a high engine speed while in a drive range, then DTC P0502 sets. DTC P0502 is a type B DTC.

CONDITIONS FOR RUNNING THE DTC


^ No MAP sensor DTC P0106, P0107, P0108, P1106 or P1107.
^ No TP sensor DTC P0121, P0122, P0123, P1121 or P1122.
^ The TP angle is greater than 12%.
^ The MAP is 0-105 kPa (0-15 psi).
^ The engine torque is 55-400 N.m (40-300 lb ft).
^ The transmission is not in PARK or NEUTRAL.
^ The input shaft speed is greater than 1500 RPM.

CONDITIONS FOR SETTING THE DTC


The output shaft speed is less than 150 RPM for 2.5 seconds.

ACTION TAKEN WHEN THE DTC SETS


^ The PCM illuminates the Malfunction Indicator Lamp (MIL) during the second consecutive trip in which the conditions for setting the DTC
are met.
^ The PCM commands maximum line pressure.
^ The PCM freezes shift adapts.
^ The PCM calculates vehicle speed from the AT input shaft speed sensor for shift timing.
^ The PCM records the operating conditions when the Conditions for Setting the DTC are met. The PCM stores this information as Freeze
Frame and Failure Records.
^ The PCM stores DTC P0502 in PCM history during the second consecutive trip in which the conditions for setting the DTC are met.

CONDITIONS FOR CLEARING THE MIL/DTC


^ The PCM turns OFF the MIL during the third consecutive trip in which the diagnostic test runs and passes.
^ A scan tool clears the DTC from the PCM history.
^ The PCM clears the DTC from the PCM history if the vehicle completes 40 consecutive warm-up cycles without an emission related
diagnostic fault occurring.
^ The PCM cancels the DTC default actions when the fault no longer exists and the ignition switch is OFF long enough in order to power down
the PCM.

DIAGNOSTIC AIDS
^ Inspect the connectors at the controller, the component and all other circuit connecting points for an intermittent condition. Refer to Testing
for Intermittent and Poor Connections in Diagrams.
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 399
Chevrolet Venture V6-3.4L VIN E 2079
^ Inspect the circuit wiring for an intermittent condition. Refer to Testing for Electrical Intermittents in Diagrams.
^ Check for Electromagnetic Interference (EMI) in circuits 400 (YEL) and 401 (PPL). EMI may be induced by a misrouted wiring harness
along the spark plug wires.

TEST DESCRIPTION
The numbers below refer to the step numbers on the diagnostic table.
3. This step test the ability of the VSS to produce an AC current. This step also verifies the integrity of the wiring to the PCM.
4. This step test the VSS circuit for correct resistance.

P0503

Diagnostic Chart 1 Of 2
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 400
Chevrolet Venture V6-3.4L VIN E 2080

Diagnostic Chart 2 Of 2
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 401
Chevrolet Venture V6-3.4L VIN E 2081

Schematic

Circuit Description with 4T65-E Automatic Transaxle


The Vehicle Speed Sensor (VSS) system is a pulse generator consisting of a speed sensor assembly, located in the case extension, and a toothed
vehicle speed sensor reluctor wheel, which is pressed onto the final drive carrier assembly. As the vehicle drives forward, the vehicle speed
sensor reluctor wheel rotates. This rotation produces a variable AC signal in the pickup coil that is proportional to vehicle speed.

The AC signal generated has a frequency and amplitude (voltage). The PCM uses the frequency to calculate the vehicle speed. The voltage
portion of the signal is used for diagnostic purposes only. The voltage will vary from 0.5 volts AC at 100 RPM to as much as 200 volts AC at
6000 RPM.

This information is then sent to the PCM to indicate how fast the vehicle is traveling and to develop the shift pattern for the transmission. Other
systems also use VSS information:
^ TCC apply and release
^ Cruise control system
^ Fuel delivery systems

If the PCM detects a large change in vehicle speed in a short period of time, then DTC P0503 sets. DTC P0503 is a type B DTC.

CONDITIONS FOR RUNNING THE DTC


^ The engine speed is more than 500 RPM for 5 seconds and not in fuel shut off.
^ The transmission is not in PARK or NEUTRAL.
^ The time since the last gear range change is more than 6 seconds.
^ No output shaft speed rise greater than 250 RPM in 2 seconds.

CONDITIONS FOR SETTING THE DTC


The output shaft speed drops greater than 1500 RPM in 3 seconds.

ACTION TAKEN WHEN THE DTC SETS


^ The PCM illuminates the Malfunction Indicator Lamp (MIL) during the second consecutive trip in which the conditions for setting the DTC
are met.
^ The PCM commands maximum line pressure.
^ The PCM freezes shift adapts.
^ The PCM calculates vehicle speed from the AT input shaft speed sensor for shift timing.
^ The PCM records the operating conditions when the Conditions for Setting the DTC are met. The PCM stores this information as Freeze
Frame and Failure Records.
^ The PCM stores DTC P0503 in PCM history during the second consecutive trip in which the conditions for setting the DTC are met.

CONDITIONS FOR CLEARING THE MIL/DTC


^ The PCM turns OFF the MIL during the third consecutive trip in which the diagnostic test runs and passes.
^ A scan tool can clear the MIL/DTC.
^ The PCM clears the DTC from the PCM history if the vehicle completes 40 consecutive warm-up cycles without an emission-related
diagnostic fault occurring.
^ The PCM cancels the DTC default actions when the fault no longer exists and the ignition switch is OFF long enough in order to power down
the PCM.

DIAGNOSTIC AIDS
^ Inspect the connectors at the controller, the component and all other circuit connecting points for an intermittent condition. Refer to Testing
for Intermittent and Poor Connections in Diagrams.
^ Inspect the circuit wiring for an intermittent condition. Refer to Testing for Electrical Intermittents in Diagrams.
^ Check for Electromagnetic Interference (EMI) in circuits 400 (YEL) and 401 (PPL). EMI may be induced by a misrouted wiring harness
along the spark plug wires.
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 402
Chevrolet Venture V6-3.4L VIN E 2082
^ Too much runout in the final drive carrier assembly may set DTC P0503.

TEST DESCRIPTION
The numbers below refer to the step numbers on the diagnostic table.
3. This step test the ability of the VSS to produce an AC current. This step also verifies the integrity of the wiring to the PCM.
4. This step test the VSS circuit for correct resistance.

P0506

Diagnostic Chart (Part 1 Of 2)


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 403
Chevrolet Venture V6-3.4L VIN E 2083

Diagnostic Chart (Part 2 Of 2)

Schematic

CIRCUIT DESCRIPTION
The Powertrain Control Module (PCM) controls engine idle speed by adjusting the position of the Idle Air Control (IAC) motor pintle. The IAC
is a bi-directional motor driven by two coils. The PCM applies current to the IAC coils in pulses to extend the IAC pintle into a passage in the
throttle body to decrease air flow. The PCM reverses the current to retract the pintle, increasing air flow. This method allows highly accurate
control of idle speed and quick response to changes in engine load. If the PCM detects a condition where too low of an idle speed is present and
the PCM is unable to adjust idle speed by increasing the IAC counts, DTC P0506 will set indicating a problem with the idle control system.

CONDITIONS FOR RUNNING THE DTC


- No active TP, ECT, MAP, IAT, MAF, CKP Sensor, EVAP, Misfire, EGR, VSS, Fuel Trim, or Injector Circuit DTCs active.
- Engine coolant temperature is above 70°C (158°F).
- The engine has been running for at least 2 minutes.
- System voltage is between 9.0-18.0 volts.
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 404
Chevrolet Venture V6-3.4L VIN E 2084
- Vehicle speed is less than 3 mph.
- Intake air temperature is above -18°C (5°F).
- The throttle is below 1.5 percent.
- BARO is above 65 kPa.

CONDITIONS FOR SETTING THE DTC


- Engine speed is more than 100 RPM less than Desired Idle.
- The above condition is present for more than 15 seconds.

ACTION TAKEN WHEN THE DTC SETS


- The PCM will illuminate the Malfunction Indicator Lamp (MIL) during the second consecutive trip in which the diagnostic test has been run
and failed.
- The PCM will store conditions which were present when the DTC set as Freeze Frame and Failure Records data.
- If the misfire is determined to be catalyst damaging, the PCM will flash the MIL.

CONDITIONS FOR CLEARING THE MIL/DTC


- The PCM will turn OFF the MIL during the third consecutive trip in which the diagnostic has been run and passed.
- The History DTC will clear after 40 consecutive warm-up cycles have occurred without a malfunction.
- The DTC can be cleared by using a scan tool.

DIAGNOSTIC AIDS
Inspect for the following conditions:
- Restricted air intake system
- Throttle body-Inspect for:
- Objects blocking the IAC passage or throttle bore
- Excessive deposits in the IAC passage and on the IAC pintle
- Excessive deposits in the throttle bore and on the throttle plate
- Large vacuum leak-Inspect for a condition that causes a large vacuum leak, such as a incorrectly installed or faulty PCV valve or brake
booster hose disconnected. Refer to Visual/Physical Inspection in Symptoms. See: Initial Inspection and Diagnostic Overview

IMPORTANT: Remove any debris from the connector surfaces before servicing a component. Inspect the connector gaskets when diagnosing
or replacing a component. Ensure that the gaskets are installed correctly. The gaskets prevent contaminate intrusion.

- Poor terminal connection-Inspect the harness connectors for backed out terminals, improper mating, broken locks, improperly formed or
damaged terminals, and faulty terminal to wire connection. Use a corresponding mating terminal to test for proper tension. Refer to
Diagrams.
- Damaged harness-Inspect the wiring harness for damage. If the harness inspection does not reveal a problem, observe the display on the scan
tool while moving connectors and wiring harnesses related to the sensor. A change in the scan tool display may indicate the location of the
fault. Refer to Diagrams.
- PCM and engine grounds for clean and secure connections

If the DTC is determined to be intermittent, reviewing the Failure Records can be useful in determining when the DTC was last set.

TEST DESCRIPTION
The number below refers to the step number on the diagnostic table:
10. .This vehicle is equipped with a PCM which utilizes an Electrically Erasable Programmable Read Only Memory (EEPROM). When the
PCM is being replaced, the new PCM must be programmed.

P0507
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 405
Chevrolet Venture V6-3.4L VIN E 2085

Diagnostic Chart
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 406
Chevrolet Venture V6-3.4L VIN E 2086

Schematic

CIRCUIT DESCRIPTION
The Powertrain Control Module (PCM) controls engine idle speed by adjusting the position of the Idle Air Control (IAC) motor pintle. The IAC
is a bi-directional motor driven by two coils. The PCM applies current to the IAC coils in pulses, counts, to extend the IAC pintle into a passage
in the throttle body to decrease air flow. The PCM reverses the current to retract the pintle, increasing air flow. This method allows highly
accurate control of idle speed and quick response to changes in engine load. If the PCM detects a condition where too low of an idle speed is
present and the PCM is unable to adjust idle speed by increasing the IAC counts, DTC P0507 will set indicating a problem with the idle control
system.

CONDITIONS FOR RUNNING THE DTC


- No active TP, ECT, MAP, IAT, MAF, CKP Sensor, EVAP, Misfire, EGR, VSS, Fuel Trim or, Injector Circuit DTCs active.
- Engine coolant temperature is above 70°C (158°F).
- The engine has been running for at least 2 minutes.
- System voltage is between 9.0-18.0 volts.
- Vehicle speed is less than 3 mph.
- Intake air temperature is above -18°C (0°F).
- The throttle is below 1.5 percent.
- BARO is above 65 kPa.
- Engine run time is more than 2 minutes.

CONDITIONS FOR SETTING THE DTC


- Engine speed is more than 175 RPM higher than Desired Idle.
- The above condition is present for more than 15 seconds.

ACTION TAKEN WHEN THE DTC SETS


- The PCM will illuminate the Malfunction Indicator Lamp (MIL) during the second consecutive trip in which the diagnostic test has been run
and failed.
- The PCM will store conditions which were present when the DTC set as Freeze Frame and Failure Records data.
- If the misfire is determined to be catalyst damaging, the PCM will flash the MIL.

CONDITIONS FOR CLEARING THE MIL/DTC


- The PCM will turn OFF the MIL during the third consecutive trip in which the diagnostic has been run and passed.
- The History DTC will clear after 40 consecutive warm-up cycles have occurred without a malfunction.
- The DTC can be cleared by using a scan tool.

DIAGNOSTIC AIDS
Inspect for the following conditions:
- Restricted air intake system-Inspect for:
- Collapsed air intake duct
- Restricted air filter element Foreign objects blocking the air intake system
- Throttle body-Inspect for:
- Objects blocking the IAC passage or throttle bore
- Excessive deposits in the IAC passage and on the IAC pintle
- Excessive deposits in the throttle bore and on the throttle plate
- Large vacuum leak-Inspect for a condition that causes a large vacuum leak, such as a incorrectly installed or faulty PCV valve or brake
booster hose disconnected.

IMPORTANT: Remove any debris from the connector surfaces before servicing a component. Inspect the connector gaskets when diagnosing
or replacing a component. Ensure that the gaskets are installed correctly. The gaskets prevent contaminate intrusion.

- Poor terminal connection-Inspect the harness connectors for backed out terminals, improper mating, broken locks, improperly formed or
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 407
Chevrolet Venture V6-3.4L VIN E 2087
damaged terminals, and faulty terminal to wire connection. Use a corresponding mating terminal to test for proper tension. Refer to
Diagrams.
- Damaged harness-Inspect the wiring harness for damage. If the harness inspection does not reveal a problem, observe the display on the scan
tool while moving connectors and wiring harnesses related to the sensor. A change in the scan tool display may indicate the location of the
fault. Refer to Diagrams.
- PCM and engine grounds for clean and secure connections

If the DTC is determined to be intermittent, reviewing the Failure Records can be useful in determining when the DTC was last set.

TEST DESCRIPTION
The numbers below refer to the step numbers on the diagnostic table:
10. Before replacing the PCM, check the terminals for improper mating, broken locks, or physical damage to the wiring harness.

P0530

Diagnostic Chart (Part 1 Of 2)


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 408
Chevrolet Venture V6-3.4L VIN E 2088

Diagnostic Chart (Part 2 Of 2)


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 409
Chevrolet Venture V6-3.4L VIN E 2089

Schematic

CIRCUIT DESCRIPTION
The A/C system uses an A/C refrigerant pressure sensor mounted in the high pressure side of the A/C refrigerant system to monitor A/C
refrigerant pressure. The Powertrain Control Module (PCM) uses this information to turn ON the engine coolant fans when the A/C refrigerant
pressure is high and to keep the compressor disengaged when A/C refrigerant pressure is excessively high or low. The A/C refrigerant pressure
sensor operates like other 3-wire sensors. The PCM applies a 5.0 volt reference and a sensor ground to the sensor. Changes in the A/C refrigerant
pressure will cause the A/C refrigerant pressure input to the PCM to vary. The PCM monitors the A/C refrigerant pressure signal circuit and can
determine when the signal is outside of the possible range of the sensor. When the signal is out of range, high or low, for a prolonged period of
time, the PCM will set DTC P0530. When DTC P0530 is set, the PCM will not allow the A/C compressor clutch to engage. This is done to
protect the compressor.

CONDITIONS FOR RUNNING THE DTC


^ The engine is running.
^ A/C is requested.

CONDITIONS FOR SETTING THE DTC


The A/C refrigerant pressure sensor signal voltage is less than 0.1 volt (9 psi).
OR
^ The A/C refrigerant pressure sensor signal voltage is more than 4.9 volts (472 psi).
^ Either of the above conditions are present for more than 20 seconds.

ACTION TAKEN WHEN THE DTC SETS


^ The PCM will not illuminate the Malfunction Indicator Lamp (MIL).
^ The PCM will store conditions which were present when the DTC set as Failure Records data only. This information will not be stored as
Freeze Frame data.

CONDITIONS FOR CLEARING THE MIL/DTC


^ A History DTC will clear after 40 consecutive warm-up cycles have occurred without a malfunction.
^ The DTC can be cleared by using a scan tool.

DIAGNOSTIC AIDS
Inspect for the following conditions:
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 410
Chevrolet Venture V6-3.4L VIN E 2090

IMPORTANT: Remove any debris from the connector surfaces before servicing a component. Inspect the connector gaskets when diagnosing
or replacing a component. Ensure that the gaskets are installed correctly. The gaskets prevent contaminate intrusion.

^ Poor terminal connection-Inspect the harness connectors for backed out terminals, improper mating, broken locks, improperly formed or
damaged terminals, and faulty terminal to wire connection. Use a corresponding mating terminal to test for proper tension.
^ Damaged harness-Inspect the wiring harness for damage. If the harness inspection does not reveal a problem, observe the display on the scan
tool while moving connectors and wiring harnesses related to the sensor. A change in the scan tool display may indicate the location of the
fault.
^ PCM and engine grounds for clean and secure connections

If the DTC is determined to be intermittent, reviewing the Failure Records can be useful in determining when the DTC was last set.

TEST DESCRIPTION
The numbers below refer to the step numbers on the diagnostic table:
3. If the A/C refrigerant pressure signal voltage stays high after disconnecting the A/C refrigerant pressure sensor electrical connector, the
signal circuit is shorted to voltage or the PCM is faulty.
6. Tests for a high resistance or an open in the ground circuit.
15. This vehicle is equipped with a PCM which utilizes an Electrically Erasable Programmable Read Only Memory (EEPROM). When the PCM
is being replaced, the new PCM must be programmed.

P0560

Diagnostic Chart (Part 1 Of 2)


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 411
Chevrolet Venture V6-3.4L VIN E 2091

Diagnostic Chart (Part 2 Of 2)

Refer to Engine Controls Schematics. See: Diagrams/Electrical Diagrams

CIRCUIT DESCRIPTION
The Powertrain Control Module (PCM) monitors system voltage on the PCM ignition feed circuit. If the system voltage is out of tolerance, DTC
P0560 will be set. When the conditions that set DTC P0560 are present, operation of some vehicle systems and components may be affected.

CONDITIONS FOR RUNNING THE DTC


Engine speed is more than 650 RPM.

CONDITIONS FOR SETTING THE DTC


- System voltage monitored at the PCM ignition feed circuit is below 9.0 volts or above 18.0 volts.
- Above conditions for more than 25 seconds.

ACTION TAKEN WHEN THE DTC SETS


- The PCM will not illuminate the Malfunction Indicator Lamp (MIL).
- The PCM will store conditions which were present when the DTC set as Failure Records data only. This information will not be stored as
Freeze Frame data.

CONDITIONS FOR CLEARING THE MIL/DTC


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 412
Chevrolet Venture V6-3.4L VIN E 2092
- A History DTC will clear after 40 consecutive warm-up cycles have occurred without a malfunction.
- The DTC can be cleared by using a scan tool.

DIAGNOSTIC AIDS
Inspect for the following conditions:
For complete information and additional diagnostics for the vehicle charging system, refer to A Diagnostic System Check - Starting and
Charging. See: Starting and Charging

IMPORTANT: Remove any debris from the connector surfaces before servicing a component. Inspect the connector gaskets when diagnosing
or replacing a component. Ensure that the gaskets are installed correctly. The gaskets prevent contaminate intrusion.

- Poor terminal connection-Inspect the harness connectors for backed out terminals, improper mating, broken locks, improperly formed or
damaged terminals, and faulty terminal to wire connection. Use a corresponding mating terminal to test for proper tension. Refer to
Diagrams.
- Damaged harness-Inspect the wiring harness for damage. If the harness inspection does not reveal a problem, observe the display on the scan
tool while moving connectors and wiring harnesses related to the sensor. A change in the scan tool display may indicate the location of the
fault. Refer to Diagrams.
- PCM and engine grounds for clean and secure connections

If the DTC is determined to be intermittent, reviewing the Failure Records can be useful in determining when the DTC was last set.

TEST DESCRIPTION
Numbers below refer to the step numbers on the Diagnostic Table:
13. This vehicle is equipped with a PCM which utilizes an Electrically Erasable Programmable Read Only Memory (EEPROM). When the PCM
is being replaced, the new PCM must be programmed.

P0601

Diagnostic Chart

CIRCUIT DESCRIPTION

The Powertrain Control Module (PCM) used in this vehicle utilizes an Electrically Erasable Programmable Read-only Memory (EEPROM). The
EEPROM contains program information and the calibrations required for powertrain diagnostics operation. Unlike the PROM used in past
applications, the EEPROM is not replaceable. When the PCM is replaced or a calibration update is required, the PCM must be programmed using
approved Techline equipment.

CONDITIONS FOR SETTING THE DTC


The PCM does not contain the correct program required to operate the vehicle.

ACTION TAKEN WHEN THE DTC SETS


- The PCM will illuminate the Malfunction Indicator Lamp (MIL) during the first trip in which the diagnostic test has been run and failed.
- The PCM will store conditions which were present when the DTC set as Freeze Frame and Failure Records data.

CONDITIONS FOR CLEARING THE MIL/DTC


- The PCM will turn OFF the MIL during the third consecutive trip in which the diagnostic has been run and passed.
- The History DTC will clear after 40 consecutive warm-up cycles have occurred without a malfunction.
- The DTC can be cleared by using a scan tool.

DIAGNOSTIC AIDS
DTC P0601 indicates that the contents of the EEPROM have changed since the PCM was programmed. The only possible repair is PCM
replacement. Remember to program the replacement PCM with the correct software and calibration for the vehicle.

TEST DESCRIPTION
Numbers below refer to the step numbers on the diagnostic table:
2. This vehicle is equipped with a PCM which utilizes an Electrically Erasable Programmable Read Only Memory (EEPROM). When the PCM
is replaced, the new PCM must be programmed.
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 413
Chevrolet Venture V6-3.4L VIN E 2093
P0602

Diagnostic Chart

CIRCUIT DESCRIPTION
The Powertrain Control Module (PCM) used in this vehicle utilizes an Electrically Erasable Programmable Read-only Memory (EEPROM).
The EEPROM contains program information and the calibrations required for powertrain diagnostics operation.

Unlike the PROM used in past applications, the EEPROM is not replaceable. When the PCM is replaced or a calibration update is required, the
PCM must be programmed using approved Techline equipment.

CONDITIONS FOR SETTING THE DTC


The PCM does not contain the correct program required to operate the vehicle.

ACTION TAKEN WHEN THE DTC SETS


- The PCM will not illuminate the Malfunction Indicator Lamp (MIL).
- The PCM will store conditions which were present when the DTC set as Failure Records data only. This information will not be stored as
Freeze. Frame data.

CONDITIONS FOR CLEARING THE MIL/DTC


- A History DTC will clear after 40 consecutive warm-up cycles have occurred without a malfunction.
- The DTC can be cleared by using the scan tool Clear Info function.

TEST DESCRIPTION
Numbers below refer to the step numbers on the diagnostic table:
2. This vehicle is equipped with a PCM which utilizes an Electrically Erasable Programmable Read Only Memory (EEPROM). When the PCM
is replaced, the new PCM must be programmed.

P0620
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 414
Chevrolet Venture V6-3.4L VIN E 2094

Diagnostic Chart

Refer to Engine Control Schematics DID, IP, and Generator. See: Diagrams/Electrical Diagrams

CIRCUIT DESCRIPTION
The PCM Output (L) terminal to the alternator determines when the alternator will be turned off. It is on under all normal vehicle operating
conditions except during low RPM conditions. The alternator is turned off during low RPM conditions to remove excess load from the engine.

The alternator telltale lamp will illuminate any time the ignition is on and engine is not running. The telltale will go out after the engine is
running and the alternator is putting out the desired amperage.

CONDITIONS FOR RUNNING THE DTC


- The engine is running.
- The voltage telltale is ON.

CONDITIONS FOR SETTING THE DTC


- (L) terminal voltage is low while the PCM is commanding the generator on.
- The above condition is present for more than 10 seconds.

ACTION TAKEN WHEN THE DTC SETS


- The PCM will illuminate the Malfunction Indicator Lamp (MIL) during the second consecutive trip in which the diagnostic has been run and
failed.
- If equipped with traction control, the PCM will command the Electronic Brake And Traction Control Module (EBTCM) via the serial data
circuit to turn OFF traction control, and the EBTCM will illuminate the TRACTION OFF lamp.
- The PCM will store conditions which were present when the DTC set as Freeze Frame and Failure Records data.

CONDITIONS FOR CLEARING THE MIL/DTC


- The PCM will turn OFF the MIL during the third consecutive trip in which the diagnostic has been run and passed.
- The History DTC will clear after 40 consecutive warm-up cycles have occurred without a malfunction.
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 415
Chevrolet Venture V6-3.4L VIN E 2095
- The DTC can be cleared by using a scan tool.

DIAGNOSTIC AIDS
Check for the following conditions:

IMPORTANT: Remove any debris from the connector surfaces before servicing a component. Inspect the connector gaskets when diagnosing
or replacing a component. Ensure that the gaskets are installed correctly. The gaskets prevent contaminate intrusion.

- Poor terminal connection-Inspect the harness connectors for backed out terminals, improper mating, broken locks, improperly formed or
damaged terminals, and faulty terminal to wire connection. Use a corresponding mating terminal to test for proper tension. Refer to
Diagrams.
- Damaged harness-Inspect the wiring harness for damage. If the harness inspection does not reveal a problem, observe the display on the scan
tool while moving connectors and wiring harnesses related to the sensor. A change in the scan tool display may indicate the location of the
fault. Refer to Diagrams.
- PCM and engine grounds for clean and secure connections

If the DTC is determined to be intermittent, reviewing the Failure Records can be useful in determining when the DTC was last set.

TEST DESCRIPTION
The numbers below refers to the step number on the diagnostic table:
7. This vehicle is equipped with a PCM which utilizes and Electrically Erasable Programmable Read Only Memory (EEPROM). When the
PCM is being replaces, the new PCM must be programmed.

P0650
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 416
Chevrolet Venture V6-3.4L VIN E 2096

Diagnostic Chart (Part 1 Of 2)

Diagnostic Chart (Part 2 Of 2)


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 417
Chevrolet Venture V6-3.4L VIN E 2097

Schematic

CIRCUIT DESCRIPTION
Output Driver Modules (ODMs) are used by the PCM to turn on many of the current-driven devices that are needed to control various engine
and Transaxle functions. Each ODM is capable of controlling up to 7 separate outputs by applying ground to the device which the PCM is
commanding ON. ODMs have the capability of diagnosing each output circuit individually. DTC P0650 set indicates an improper voltage level
on the output circuit that controls the Malfunction Indicator Lamp (MIL).

CONDITIONS FOR RUNNING THE DTC


Ignition is ON.

CONDITIONS FOR SETTING THE DTC


- An improper voltage level has been detected on the output circuit which controls the Malfunction Indicator Lamp (MIL).
- Above conditions for at least 30 seconds.

DIAGNOSTIC AIDS
Inspect for the following conditions:

IMPORTANT: If the Instrument Panel (I/P) is completely inoperative, refer to A Diagnostic System Check -Instrument Cluster in Instrument
Panel, Gauges and Warning Indicators for further diagnosis. See: Instrument Panel, Gauges and Warning Indicators

If the ignition feed circuit is suspected of being open, observe if other lamps on that circuit illuminate.

IMPORTANT: Remove any debris from the connector surfaces before servicing a component. Inspect the connector gaskets when diagnosing
or replacing a component. Ensure that the gaskets are installed correctly. The gaskets prevent contaminate intrusion.

- Poor terminal connection-Inspect the harness connectors for backed out terminals, improper mating, broken locks, improperly formed or
damaged terminals, and faulty terminal to wire connection. Use a corresponding mating terminal to test for proper tension. Refer to
Diagrams.
- Damaged harness-Inspect the wiring harness for damage. If the harness inspection does not reveal a problem, observe the display on the scan
tool while moving connectors and wiring harnesses related to the sensor. A change in the scan tool display may indicate the location of the
fault. Refer to Diagrams.
- PCM and engine grounds for clean and secure connections

If the DTC is determined to be intermittent, reviewing the Failure Records can be useful in determining when the DTC was last set.

TEST DESCRIPTION
Number(s) below refer to the step number(s) on the Diagnostic Table.
11. This vehicle is equipped with a PCM which utilizes an Electrically Erasable Programmable Read Only Memory (EEPROM). When the PCM
is replaced, the new PCM must be programmed.

P0711
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 418
Chevrolet Venture V6-3.4L VIN E 2098

Diagnostic Chart 1 Of 2
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 419
Chevrolet Venture V6-3.4L VIN E 2099

Diagnostic Chart 2 Of 2
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 420
Chevrolet Venture V6-3.4L VIN E 2100

Schematic

Circuit Description with 4T65-E Automatic Transaxle


The automatic Transmission Fluid Temperature (TFT) sensor is a negative coefficient thermistor. When the transmission fluid is cold, the sensor
resistance is high. As the transmission fluid warms up, the sensor resistance decreases. This diagnostic monitors the TFT sensor circuit. The
circuit may be functional but not in the normal operating range. This diagnostic indicates stuck, erratic, intermittent, or skewed values, resulting
in reduced system performance. The TFT sensor range is -40 to +151°C (-40 to +304°F).

If the PCM detects an intermittent voltage or no voltage change in the TFT sensor circuit, then DTC P0711 sets. DTC P0711 is a type C DTC.

CONDITIONS FOR RUNNING THE DTC


^ No VSS DTC P0502 or P0503.
^ The system voltage is 9-18 volts.
^ The engine coolant temperature is 70°C (158°F) or more.
^ The engine coolant temperature has changed by 50°C (90°F) or more since start-up.
^ The engine run time is more than 5 minutes.
^ The TFT sensor voltage is 0.2-4.92 volts.
^ The transmission fluid temperature at start-up is -40 to 21°C (-40 to 69°F).
^ The vehicle speed is greater than 8 km/h (5 mph) for at least 6 minutes and 49 seconds cumulative.
^ The TCC slip is greater than 80 RPM for at least 6 minutes and 49 seconds cumulative.

CONDITIONS FOR SETTING THE DTC


DTC P0711 sets when one of the following conditions occurs:

Condition 1
The change in transmission fluid temperature is less than 1.5°C (2°F) since start-up for at least 6 minutes and 49 seconds continuous.

Condition 2
The change in transmission fluid temperature is greater than 20°C (36°F) within 0.2 seconds and this occurs at least 14 times within 7
seconds.

ACTION TAKEN WHEN THE DTC SETS


^ The PCM does not illuminate the Malfunction Indicator Lamp (MIL).
^ The PCM freezes shift adapts.
^ The PCM calculates a default TFT from the ECT sensor and the IAT sensor.
^ The PCM records the operating conditions when the Conditions for Setting the DTC are met. The PCM stores this information as Failure
Records.
^ The PCM stores DTC P0711 in PCM history.

CONDITIONS FOR CLEARING THE DTC


^ A scan tool can clear the DTC.
^ The PCM clears the DTC from PCM history if the vehicle completes 40 consecutive warm-up cycles without a non-emission-related
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 421
Chevrolet Venture V6-3.4L VIN E 2101
diagnostic fault occurring.
^ The PCM cancels the DTC default actions when the fault no longer exists and the ignition switch is OFF long enough in order to power down
the PCM.

DIAGNOSTIC AIDS
^ Inspect the connectors at the controller, the component and all other circuit connecting points for an intermittent condition. Refer to Testing
for Intermittent and Poor Connections in Diagrams.
^ Inspect the circuit wiring for an intermittent condition. Refer to Testing for Electrical Intermittents in Diagrams.
^ Test the TFT sensor at various temperature levels to evaluate the possibility of a skewed (mis-scaled) sensor. Refer to the Transmission Fluid
Temperature (TFT) Sensor Specifications table.
^ Inspect the transmission 20-way connector for transmission fluid.

TEST DESCRIPTION
The numbers below refer to the step numbers on the diagnostic table.
3. This step attempts to repeat the condition that set the DTC.
5. This step attempts to repeat the condition in the engine wiring harness.
6. This step determines if a condition exists with the PCM or TFT sensor.

P0712

Diagnostic Chart 1 Of 2
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 422
Chevrolet Venture V6-3.4L VIN E 2102

Diagnostic Chart 2 Of 2

Schematic

Circuit Description with 4T65-E Automatic Transaxle


The automatic Transmission Fluid Temperature (TFT) sensor is a negative coefficient thermistor whose resistance value changes based on
temperature. The PCM provides a 5 volt reference to the sensor circuit. A high fluid temperature or a short to ground on the sensor circuit results
in low signal voltage. The TFT sensor operating range is-40 to +151°C (-40 to +304°F).

If the PCM detects a continuous short to ground in the TFT sensor circuit, then DTC P0712 sets. DTC P0712 is a type C DTC.
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 423
Chevrolet Venture V6-3.4L VIN E 2103

CONDITIONS FOR RUNNING THE DTC


The system voltage is 9-18 volts.

CONDITIONS FOR SETTING THE DTC


The PCM detects a TFT sensor voltage of less than 0.2 volts for 10 seconds.

ACTION TAKEN WHEN THE DTC SETS


^ The PCM does not turn on the Malfunction Indicator Lamp (MIL).
^ The PCM freezes shift adapts.
^ The PCM calculates a default TFT from the ECT sensor and the IAT sensor.
^ The PCM records the operating conditions when the Conditions for Setting the DTC are met. The PCM stores this information as Failure
Records.
^ The PCM stores DTC P0712 in PCM history.

CONDITIONS FOR CLEARING THE DTC


^ A scan tool can clear the DTC.
^ The PCM clears the DTC from PCM history if the vehicle completes 40 consecutive warm-up cycles without a non-emission-related
diagnostic fault occurring.
^ The PCM cancels the DTC default actions when the fault no longer exists and the ignition switch is OFF long enough in order to power down
the PCM.

DIAGNOSTIC AIDS
^ Inspect the connectors at the controller, the component and all other circuit connecting points for an intermittent condition. Refer to Testing
for Intermittent and Poor Connections in Diagrams.
^ Inspect the circuit wiring for an intermittent condition. Refer to Testing for Electrical Intermittents in Diagrams.

TEST DESCRIPTION
The numbers below refer to the step numbers on the diagnostic table.
2. A value below 0.2 volts indicates the fault is present. A value above 0.2 volts indicates the fault is intermittent.
3. A value greater than 4.9 volts indicates the fault is in the transmission side.
5. For resistance at other temperatures, refer to Transmission Fluid Temperature (TFT) Sensor Specifications.
6. A value less than 10 K ohm indicates a short to ground in the harness or sensor. A value greater than 10 K ohm indicates the condition is
intermittent.
7. A value less than 10 K ohm indicates a short together between the TFT signal circuit and the ground circuits.

P0713
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 424
Chevrolet Venture V6-3.4L VIN E 2104

Diagnostic Chart 1 Of 2
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 425
Chevrolet Venture V6-3.4L VIN E 2105

Diagnostic Chart 2 Of 2

Schematic

Circuit Description with 4T65-E Automatic Transaxle


The automatic Transmission Fluid Temperature (TFT) sensor is a negative coefficient thermistor whose resistance value changes based on
temperature. The PCM provides a 5 volt reference to the sensor. A low fluid temperature, an open TFT sensor or sensor circuit results in high
signal voltage. The TFT operating range is -40 to +151°C (-40 to +304°F).

If the PCM detects a continuous open or a short to power on the TFT sensor circuit, then DTC P0713 sets. DTC P0713 is a type C DTC.

CONDITIONS FOR RUNNING THE DTC


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 426
Chevrolet Venture V6-3.4L VIN E 2106
The system voltage is 9-18 volts.

CONDITIONS FOR SETTING THE DTC


The PCM detects a TFT sensor voltage greater than 4.92 volts for 6 minutes and 40 seconds continuous.

ACTION TAKEN WHEN THE DTC SETS


^ The PCM does not turn on the Malfunction Indicator Lamp (MIL).
^ The PCM freezes shift adapts.
^ The PCM calculates a default TFT from the ECT sensor and the IAT sensor.
^ The PCM records the operating conditions when the Conditions for Setting the DTC are met. The PCM stores this information as Failure
Records.
^ The PCM stores DTC P0713 in PCM history.

CONDITIONS FOR CLEARING THE DTC


^ A scan tool can clear the DTC.
^ The PCM clears the DTC from PCM history if the vehicle completes 40 consecutive warm-up cycles without a non-emission-related
diagnostic fault occurring.
^ The PCM cancels the DTC default actions when the fault no longer exists and the ignition switch is OFF long enough in order to power down
the PCM.

DIAGNOSTIC AIDS
^ Inspect the connectors at the controller, the component and all other circuit connecting points for an intermittent condition. Refer to Testing
for Intermittent and Poor Connections in Diagrams.
^ Inspect the circuit wiring for an intermittent condition. Refer to Testing for Electrical Intermittents in Diagrams.

TEST DESCRIPTION
The numbers below refer to the step numbers on the diagnostic table.
3. A value above 4.9 volts indicates the fault is present. A value below 4.9 volts indicates the fault is intermittent.
4. A value less than 0.2 volts indicates the PCM and engine wiring are good.

P0716
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 427
Chevrolet Venture V6-3.4L VIN E 2107
Diagnostic Chart 1 Of 2

Diagnostic Chart 2 Of 2
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 428
Chevrolet Venture V6-3.4L VIN E 2108

Schematic

Circuit Description with 4T65-E Automatic Transaxle


The Automatic Transmission Input Shaft Speed (AT ISS) sensor is a permanent magnet with a coil of wire wound around it. The AT ISS sensor
mounts in the case cover facing the reluctor wheel of the input shaft. As the reluctor wheel is driven by the turbine shaft, an AC signal is induced
in the input speed sensor. Higher vehicle speeds induce a higher frequency and voltage at the sensor.

There is a fixed air gap between the sensor and the teeth on the sensor reluctor wheel. The AT ISS sensor input is used by the PCM in order to
control line pressure, TCC apply and release and transmission shift patterns. This sensor is also used to calculate the appropriate gear ratios and
TCC slippage.

This diagnostic indicates stuck, erratic, or intermittent values, indicating poor performance of the system. If the PCM detects an unrealistically
large change in data from the AT ISS sensor in a short period of time, then DTC P0716 sets. DTC P0716 is a type B DTC.

CONDITIONS FOR RUNNING THE DTC


^ No TP sensor DTC P0121, P0122 or P0123.
^ No VSS DTC P0502 or P0503.
^ No AT ISS sensor DTC P0717 is set and DTC P0717 has passed this ignition cycle.
^ No 1-2,3-4 shift solenoid valve DTC P0751, P0752 or P0753.
^ No 2-3 shift solenoid valve DTC P0756, P0757 or P0758.
^ The engine speed is greater than 500 RPM for 5 seconds and not in fuel shut off.
^ The TP angle is greater than 14%.
^ The vehicle speed is greater than 8 km/h (5 mph).

CONDITIONS FOR SETTING THE DTC


The input shaft speed changes by greater than 1300 RPM in 0.8 seconds.

ACTION TAKEN WHEN THE DTC SETS


^ The PCM illuminates the Malfunction Indicator Lamp (MIL) during the second consecutive trip in which the Conditions for Setting the DTC
are met.
^ The PCM inhibits TCC.
^ The PCM freezes shift adapts.
^ The PCM inhibits 4th gear if the transmission is in Hot Mode.
^ The PCM records the operating conditions when the Conditions for Setting the DTC are met. The PCM stores this information as Freeze
Frame and Failure Records.
^ The PCM stores DTC P0716 in PCM history during the second consecutive trip in which the Conditions for Setting the DTC are met.

CONDITIONS FOR CLEARING THE MIL/DTC


^ The PCM turns OFF the MIL during the third consecutive trip in which the diagnostic test runs and passes.
^ A scan tool can clear the MIL/DTC.
^ The PCM clears the DTC from the PCM history if the vehicle completes 40 consecutive warm-up cycles without an emission-related
diagnostic fault occurring.
^ The PCM cancels the DTC default actions when the fault no longer exists and the ignition switch is OFF long enough in order to power down
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 429
Chevrolet Venture V6-3.4L VIN E 2109
the PCM.

DIAGNOSTIC AIDS
^ Inspect the connectors at the controller, the component and all other circuit connecting points for an intermittent condition. Refer to Testing
for Intermittent and Poor Connections in Diagrams.
^ Inspect the circuit wiring for an intermittent condition. Refer to Testing for Electrical Intermittents in Diagrams.
^ Check for Electromagnetic Interference (EMI) in the signal and ground circuits. EMI may be induced by a misrouted wiring harness along
the spark plug wires.

TEST DESCRIPTION
The numbers below refer to the step numbers on the diagnostic table.
2. This step checks if the PCM receives a signal from the AT ISS sensor.
3. A Yes answer indicates that the transmission side of the circuit is functioning properly.
4. This step checks the engine harness from the transmission 20-way connector to the PCM.
7. This step begins the transmission harness diagnosis.

P0717

Diagnostic Chart 1 Of 2
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 430
Chevrolet Venture V6-3.4L VIN E 2110

Diagnostic Chart 2 Of 2
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 431
Chevrolet Venture V6-3.4L VIN E 2111

Schematic

Circuit Description with 4T65-E Automatic Transaxle


The Automatic Transmission Input Shaft Speed (AT ISS) sensor is a permanent magnet with a coil of wire wound around it. The AT ISS sensor
mounts in the case cover facing the reluctor wheel of the input shaft. As the reluctor wheel is driven by the turbine shaft, an AC signal is induced
in the input speed sensor. Higher vehicle speeds induce a higher frequency and voltage at the sensor.

There is a fixed air gap between the sensor and the teeth on the sensor reluctor wheel. The AT ISS sensor input is used by the PCM in order to
control line pressure, TCC apply and release and transmission shift patterns. This sensor is also used to calculate the gear ratios and TCC
slippage.

If the PCM detects a low input speed while the vehicle and engine speeds are high, then DTC P0717 sets. DTC P0717 is a type B DTC.

CONDITIONS FOR RUNNING THE DTC


^ No VSS DTC P0502 or P0503.
^ No TFP manual valve position switch DTC P1810.
^ The engine speed is greater than 500 RPM for 5 seconds and not in fuel shut off.
^ The TFP manual valve position switch indicates that the transmission is not in PARK or NEUTRAL.
^ The vehicle speed is greater than 8 km/h (5 mph).

CONDITIONS FOR SETTING THE DTC


The input shaft speed is less than 50 RPM for 5 seconds.

ACTION TAKEN WHEN THE DTC SETS


^ The PCM illuminates the Malfunction Indicator Lamp (MIL) during the second consecutive trip in which the Conditions for Setting the DTC
are met.
^ The PCM inhibits TCC.
^ The PCM freezes shift adapts.
^ The PCM inhibits 4th gear if the transmission is in Hot Mode.
^ The PCM records the operating conditions when the Conditions for Setting the DTC are met. The PCM stores this information as Freeze
Frame and Failure Records.
^ The PCM stores DTC P0717 in PCM history during the second consecutive trip in which the Conditions for Setting the DTC are met.

CONDITIONS FOR CLEARING THE MIL/DTC


^ The PCM turns OFF the MIL during the third consecutive trip in which the diagnostic test runs and passes.
^ A scan tool can clear the MIL/DTC.
^ The PCM clears the DTC from the PCM history if the vehicle completes 40 consecutive warm-up cycles without an emission-related
diagnostic fault occurring.
^ The PCM cancels the DTC default actions when the fault no longer exists and the ignition switch is OFF long enough in order to power down
the PCM.

DIAGNOSTIC AIDS
^ Inspect the connectors at the controller, the component and all other circuit connecting points for an intermittent condition. Refer to Testing
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 432
Chevrolet Venture V6-3.4L VIN E 2112
for Intermittent and Poor Connections in Diagrams.
^ Inspect the circuit wiring for an intermittent condition. Refer to Testing for Electrical Intermittents in Diagrams.
^ Check for Electromagnetic Interference (EMI) in the signal and ground circuits. EMI may be induced by a misrouted wiring harness along
the spark plug wires.

TEST DESCRIPTION
The numbers below refer to the step numbers on the diagnostic table.
2. This step checks if the PCM receives a signal from the AT ISS sensor.
3. A Yes answer indicates that the transmission side of the circuit is functioning properly.
4. This step checks the engine harness from the transmission 20-way connector to the PCM.
7. This step begins the transmission harness diagnosis.

P0719

Diagnostic Chart 1 Of 2
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 433
Chevrolet Venture V6-3.4L VIN E 2113

Diagnostic Chart 2 Of 2

Schematic

Circuit Description with 4T65-E Automatic Transaxle


The TCC brake switch indicates brake pedal status to the PCM. The TCC brake switch indicates that the brake pedal is either applied or released.
The normally-closed switch supplies battery voltage to the PCM. Applying the brake pedal opens the TCC brake switch, interrupting voltage to
the PCM. When the PCM receives 0 volts at the TCC brake switch input, the PCM turns OFF the Torque Converter Clutch Pulse Width
Modulation (TCC PWM) solenoid valve.

If the PCM detects an open brake switch (indicating pedal applied) during a number of accelerations, then DTC P0719 sets. DTC P0719 is a type
C DTC.

CONDITIONS FOR RUNNING THE DTC


No VSS DTC P0502 or P0503.

CONDITIONS FOR SETTING THE DTC


The TCC brake switch indicates continuously OPEN (0 volts) for more than 15 minutes and the following conditions occur 8 times
consecutively.
^ The vehicle speed is less than 8 km/h (5 mph);
^ Then the vehicle speed is between 8 and 32 km/h (5 and 20 mph) for at least 3 seconds;
^ Finally, the vehicle speed remains above 32 km/h (20 mph) for 6 seconds.

ACTION TAKEN WHEN THE DTC SETS


^ The PCM does not illuminate the Malfunction Indicator Lamp (MIL).
^ The PCM disregards the TCC brake switch for TCC scheduling when all of the following conditions are met:
- The TP angle is greater than 6%.
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 434
Chevrolet Venture V6-3.4L VIN E 2114
- The vehicle speed is greater than 60 km/h (37 mph).
- The TP angle was previously greater than 12% while the vehicle speed was greater than 68 km/h (42 mph).
- The TCC brake switch has not indicated OFF for more than 2 seconds this trip.
^ The PCM records the operating conditions when the Conditions for Setting the DTC are met. The PCM stores this information as Failure
Records.
^ The PCM stores DTC P0719 in PCM history.

CONDITIONS FOR CLEARING THE DTC


^ A scan tool can clear the DTC.
^ The PCM clears the DTC from PCM history if the vehicle completes 40 consecutive warm-up cycles without a non-emission-related
diagnostic fault occurring.
^ The PCM cancels the DTC default actions when the fault no longer exists and the ignition switch is OFF long enough in order to power down
the PCM.

DIAGNOSTIC AIDS
^ Inspect the connectors at the controller, the component and all other circuit connecting points for an intermittent condition. Refer to Testing
for Intermittent and Poor Connections in Diagrams.
^ Inspect the circuit wiring for an intermittent condition. Refer to Testing for Electrical Intermittents in Diagrams.

TEST DESCRIPTION
The numbers below refer to the step numbers on the diagnostic table.
6. This step isolates the fault between the TCC brake switch and the harness.

P0724
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 435
Chevrolet Venture V6-3.4L VIN E 2115

Diagnostic Chart

Schematic
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 436
Chevrolet Venture V6-3.4L VIN E 2116

Circuit Description with 4T65-E Automatic Transaxle


The TCC brake switch indicates brake pedal status to the PCM. The TCC brake switch indicates that the brake pedal is either applied or released.
The normally-closed switch supplies battery voltage to the PCM. Applying the brake pedal opens the TCC brake switch, interrupting voltage to
the PCM. When the PCM receives 0 volts at the TCC brake switch input, the PCM turns OFF the Torque Converter Clutch Pulse Width
Modulation (TCC PWM) solenoid valve.

If the PCM detects a closed TCC brake switch (indicating pedal released) during a number of decelerations, then DTC P0724 sets. DTC P0724 is
a type C DTC.

CONDITIONS FOR RUNNING THE DTC


No VSS DTC P0502 or P0503.

CONDITIONS FOR SETTING THE DTC


The TCC brake switch indicates continuously CLOSED (12 volts) while the following conditions occur 8 times consecutively:
^ The vehicle speed is greater than 32 km/h (20 mph) for 6 seconds;
^ Then the vehicle speed decreases to 8 km/h (5 mph) and takes 3 seconds;
^ Finally, the vehicle speed is less than 8 km/h (5 mph).

ACTION TAKEN WHEN THE DTC SETS


^ The PCM does not illuminate the Malfunction Indicator Lamp (MIL).
^ The PCM records the operating conditions when the Conditions for Setting the DTC are met. The PCM stores this information as Failure
Records.
^ The PCM stores DTC P0724 in PCM history.

CONDITIONS FOR CLEARING THE DTC


^ A scan tool can clear the DTC.
^ The PCM clears the DTC from PCM history if the vehicle completes 40 consecutive warm-up cycles without a non-emission-related
diagnostic fault occurring.
^ The PCM cancels the DTC default actions when the fault no longer exists and the ignition switch is OFF long enough in order to power down
the PCM.

DIAGNOSTIC AIDS
^ Inspect the connectors at the controller, the component and all other circuit connecting points for an intermittent condition. Refer to Testing
for Intermittent and Poor Connections in Diagrams.
^ Inspect the circuit wiring for an intermittent condition. Refer to Testing for Electrical Intermittents in Diagrams.

TEST DESCRIPTION
The numbers below refer to the step numbers on the diagnostic table.
2. A Scan Tool display that changes from Closed to Open when the switch is disconnected indicates a faulty switch.

P0730

Diagnostic Chart 1 Of 2
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 437
Chevrolet Venture V6-3.4L VIN E 2117

Diagnostic Chart 2 Of 2

Circuit Description with 4T65-E Automatic Transaxle


The PCM calculates the gear ratio based on data from the Automatic Transmission Input Shaft Speed (AT ISS) sensor arid the Vehicle Speed
Sensor (VSS). The PCM compares the known transmission gear ratio to a calculated ratio for each gear range selected. The VSS output is
translated to RPM and mph by the PCM for various uses.

If the PCM detects an incorrect gear ratio because of excessive slip within the transmission, then DTC P0730 sets. DTC P0730 is a type C DTC.

CONDITIONS FOR RUNNING THE DTC


^ No TP sensor DTC P0121, P0122 or P0123.
^ No VSS DTC P0502 or P0503.
^ No AT ISS sensor DTC P0716 or P0717.
^ No TFP manual valve position switch DTC P1810.
^ The engine speed is greater than 500 RPM for 5 seconds and not in fuel shut off.
^ The transmission is not in PARK or NEUTRAL.
^ The transmission fluid temperature is greater than 20°C (68°F).
^ The TP angle is greater than 14%.
^ The vehicle speed is greater than 11 km/h (7 mph).
^ The engine torque is 70-270 N.m (50-300 lb ft).
^ The time since the last gear range change is greater than 6 seconds.
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 438
Chevrolet Venture V6-3.4L VIN E 2118

CONDITIONS FOR SETTING THE DTC


DTC P0730 sets when one of the following conditions occurs for 7 seconds:
^ The gear ratio is more than 2.97:1.
^ The gear ratio is 2.43:1 to 2.87:1.
^ The gear ratio is 1.62:1 to 2.33:1.
^ The gear ratio is 1.05:1 to 1.52:1.
^ The gear ratio is 0.75:1 to 0.95:1.

ACTION TAKEN WHEN THE DTC SETS


^ The PCM does not illuminate the Malfunction Indicator Lamp (MIL).
^ The PCM commands maximum line pressure.
^ The PCM freezes shift adapts.
^ The PCM records the operating conditions when the Conditions for Setting the DTC are met. The PCM stores this information as Failure
Records.
^ The PCM stores DTC P0730 in PCM history.

CONDITIONS FOR CLEARING THE DTC


^ A scan tool can clear the DTC.
^ The PCM clears the DTC from PCM history if the vehicle completes 40 consecutive warm-up cycles without a non-emission-related
diagnostic fault occurring.
^ The PCM cancels the DTC default actions when the fault no longer exists and the ignition switch is OFF long enough in order to power down
the PCM.

DIAGNOSTIC AIDS
^ Ask the customer about possible vehicle overloading, exceeding the trailer towing limit, or towing in overdrive.
^ Inspect for an incorrect calibration.
^ Refer to Range Reference.

TEST DESCRIPTION
The numbers below refer to the step numbers on the diagnostic table.
3. This step tests for low fluid level, which may cause slipping and result in an undefined gear ratio.
4. This step verifies that the correct gear ratios occur for commanded gears.
5. This step tests for low line pressure.

P0741
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 439
Chevrolet Venture V6-3.4L VIN E 2119
Diagnostic Chart 1 Of 2

Diagnostic Chart 2 Of 2
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 440
Chevrolet Venture V6-3.4L VIN E 2120

Schematic

Circuit Description with 4T65-E Automatic Transaxle


The PCM controls the Torque Converter Clutch Pulse Width Modulation (TCC PWM) solenoid valve. The solenoid controls the hydraulic fluid
for TCC apply and release. When the TCC is fully applied, the engine is coupled directly to the transmission through the TCC.

The TCC used is an Electronically Controlled Capacity Clutch (ECCC). The PCM will normally allow a small amount of slip to occur with the
ECCC. When the TCC is engaged, TCC slip speed is maintained at approximately 20 to 50 RPM.

If the PCM detects high torque converter slip when the TCC is commanded ON, then DTC P0741 sets. DTC P0741 is a type B DTC.

CONDITIONS FOR RUNNING THE DTC


^ No TP sensor DTC P0121, P0122 or P0123.
^ No VSS DTC P0502 or P0503.
^ No AT ISS sensor DTC P0716 or P0717.
^ No TCC stuck ON DTC P0742.
^ No TFP manual valve position switch DTC P1810.
^ No TCC PWM solenoid valve DTC P1860.
^ No TCC release switch DTC P1887.
^ The engine speed is greater than 500 RPM for 5 seconds and not in fuel shut off.
^ The transmission gear range is D4, D3 or D2.
^ The time since the last gear range change is greater than 6 seconds.
^ The transmission fluid temperature is 20-130°C (68-266°F).
^ The TP angle is 4-35%.
^ The TCC PWM solenoid valve is commanded ON for more than 0.5 seconds.
^ The TCC is at maximum apply pressure.

CONDITIONS FOR SETTING THE DTC


The TCC slip speed is greater than 180 RPM two times for 7 seconds each, during the same ignition cycle.

ACTION TAKEN WHEN THE DTC SETS


^ The PCM illuminates the Malfunction Indicator Lamp (MIL) during the second consecutive trip in which the conditions for setting the DTC
are met.
^ The PCM inhibits TCC.
^ The PCM inhibits 4th gear if the transmission is in Hot Mode.
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 441
Chevrolet Venture V6-3.4L VIN E 2121
^ The PCM freezes shift adapts.
^ The PCM records the operating conditions when the Conditions for Setting the DTC are met. The PCM stores this information as Freeze
Frame and Failure Records.
^ The PCM stores DTC P0741 in PCM history during the second consecutive trip in which the conditions for setting the DTC are met.

CONDITIONS FOR CLEARING THE MIL/DTC


^ The PCM turns OFF the MIL during the third consecutive trip in which the diagnostic test runs and passes.
^ A scan tool can clear the MIL/DTC.
^ The PCM clears the DTC from the PCM history if the vehicle completes 40 consecutive warm-up cycles without an emission-related
diagnostic fault occurring.
^ The PCM cancels the DTC default actions when the fault no longer exists and the ignition switch is OFF long enough in order to power down
the PCM.

DIAGNOSTIC AIDS
^ Inspect the connectors at the controller, the component and all other circuit connecting points for an intermittent condition. Refer to Testing
for Intermittent and Poor Connections in Diagrams.
^ Inspect the circuit wiring for an intermittent condition. Refer to Testing for Electrical Intermittents in Diagrams.

TEST DESCRIPTION
The numbers below refer to the step numbers on the diagnostic table.
5. This step verifies that the TCC engages when commanded ON by the Scan Tool.

P0742
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 442
Chevrolet Venture V6-3.4L VIN E 2122

Diagnostic Chart 1 Of 2
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 443
Chevrolet Venture V6-3.4L VIN E 2123

Diagnostic Chart 2 Of 2
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 444
Chevrolet Venture V6-3.4L VIN E 2124

Schematic

Circuit Description with 4T65-E Automatic Transaxle


The TCC release switch is part of the automatic Transmission Fluid Pressure (TFP) manual valve position switch. The TFP manual valve
position switch is mounted to the transmission valve body.

The TCC release switch is a normally-closed switch. When the TCC is released, TCC release fluid pressure opens the TCC release switch which
opens the TCC release pressure circuit. When the voltage on the circuit is high (switch open), the PCM recognizes that the TCC is no longer
engaged.

If the PCM detects that the TCC release switch is closed when the TCC is commanded OFF, then DTC P0742 sets. DTC P0742 is a type A DTC.

CONDITIONS FOR RUNNING THE DTC


^ No TP sensor DTC P0121, P0122 or P0123.
^ No TCC PWM solenoid valve DTC P1860.
^ No TCC release switch DTC P1887.
^ The engine speed is greater than 500 RPM and not in fuel shut off.
^ Engine torque is 95-270 N.m (70-200 lb ft).
^ The TP angle is 5-45%.
^ The transmission fluid temperature is 20-130°C (68-266°F).
^ The time since the last gear range change is greater than 6 seconds.
^ The speed ratio is less than 7.0.
^ The TCC is commanded OFF.
^ Slip speed is -20 to +25 for 8 seconds.

CONDITIONS FOR SETTING THE DTC


The TCC release switch is closed 6 times for 4 seconds each, during one trip.

ACTION TAKEN WHEN THE DTC SETS


^ The PCM illuminates the Malfunction Indicator Lamp (MIL).
^ The PCM commands the TCC ON at maximum capacity.
^ The PCM freezes shift adapts.
^ The PCM records the operating conditions when the Conditions for Setting the DTC are met. The PCM stores this information as Freeze
Frame and Failure Records.
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 445
Chevrolet Venture V6-3.4L VIN E 2125
^ The PCM stores DTC P0742 in PCM history.

CONDITIONS FOR CLEARING THE MIL/DTC


^ The PCM turns OFF the MIL during the third consecutive trip in which the diagnostic test runs and passes.
^ A scan tool can clear the MIL/DTC.
^ The PCM clears the DTC from the PCM history if the vehicle completes 40 consecutive warm-up cycles without an emission-related
diagnostic fault occurring.
^ The PCM cancels the DTC default actions when the fault no longer exists and the ignition switch is OFF long enough in order to power down
the PCM.

DIAGNOSTIC AIDS
^ Inspect the connectors at the controller, the component and all other circuit connecting points for an intermittent condition. Refer to Testing
for Intermittent and Poor Connections in Diagrams.
^ Inspect the circuit wiring for an intermittent condition. Refer to Testing for Electrical Intermittents in Diagrams.
^ Rapid fluctuation in line pressure could set DTC P0742.
^ An open condition in the TCC release circuit or switch would set DTC P1887. Open circuits are not diagnosed in DTC P0742.
^ Inspect for a pressure regulator condition.
^ Inspect for abnormal line pressure.
^ The customer may notice an engine stalling condition.

TEST DESCRIPTION
The numbers below refer to the step numbers on the diagnostic table.
3. A Yes answer indicates that the TCC is functioning properly.
4. By disconnecting the transmission connector, the PCM should interpret the open circuit as TCC release pressure present. A Yes answer
indicates that the engine side of the circuit is functioning properly.
9. This step tests for a mechanical or hydraulic condition.

P0748

Diagnostic Chart 1 Of 3
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 446
Chevrolet Venture V6-3.4L VIN E 2126

Diagnostic Chart 2 Of 3
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 447
Chevrolet Venture V6-3.4L VIN E 2127

Diagnostic Chart 3 Of 3
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 448
Chevrolet Venture V6-3.4L VIN E 2128

Schematic

Circuit Description with 4T65-E Automatic Transaxle


The Pressure Control (PC) solenoid valve is located in the valve body. The PC solenoid valve controls transmission line pressure based on
current flow through its windings. The PCM determines desired line pressure based on throttle position and other inputs. The PCM then varies
the duty cycle on the high side of the PC solenoid valve to control current flow to the solenoid. Current is controlled from about 0.02 amps for
maximum line pressure to 1.1 amps for minimum line pressure. The PCM monitors the actual current to the solenoid.

If the PCM detects a commanded current draw that differs from the actual current draw by more than a calibrated value, then DTC P0748 sets.
DTC P0748 is a type C DTC.

CONDITIONS FOR RUNNING THE DTC


^ The PC solenoid valve is enabled.
^ The system voltage is:
- Greater than 11 volts at a low temperature of -40°C (-40°F).
- Greater than 13 volts at a high temperature of 151°C (304°F).

CONDITIONS FOR SETTING THE DTC


DTC P0748 sets when the duty cycle is outside the range of 0.5-95% for 0.2 seconds.

ACTION TAKEN WHEN THE DTC SETS


^ The PCM does not illuminate the Malfunction Indicator Lamp (MIL).
^ The PCM enters PC solenoid valve diagnostic retest mode. The retest mode conducts the following diagnostic routine:
1. The PCM de-energizes the PC solenoid valve, resulting in maximum line pressure.
2. After being de-energized for 2 seconds, the PCM commands the PC solenoid valve ON at 0.1 amp for the retest period of 5 seconds.
^ If no circuit faults are detected during the 5 second retest period, then the PC solenoid valve is returned to normal operation and DTC
P0748 diagnostic is passed.
If a circuit fault is detected 3 times during normal operation, then the PCM de-energizes the PC solenoid valve for the remainder of
that ignition cycle.
^ If a circuit fault is detected during the 5 second retest period, then the PCM de-energizes the PC solenoid valve for 2 secondsbefore
reentering the retest mode.
If a circuit fault is detected 5 times without returning to normal operation, then the PC solenoid valve is de-energized for the
remainder of that ignition cycle.
^ The PCM freezes shift adapts.
^ The PCM records the operating conditions when the Conditions for Setting the DTC are met. The PCM stores this information as Failure
Records.
^ The PCM stores DTC P0748 in PCM history.

CONDITIONS FOR CLEARING THE DTC


^ A scan tool can clear the DTC.
^ The PCM clears the DTC from PCM history if the vehicle completes 40 consecutive warm-up cycles without a non-emission-related
diagnostic fault occurring.
^ The PCM cancels the DTC default actions when the fault no longer exists and the ignition switch is OFF long enough in order to power down
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 449
Chevrolet Venture V6-3.4L VIN E 2129
the PCM.

DIAGNOSTIC AIDS
^ Inspect the connectors at the controller, the component and all other circuit connecting points for an intermittent condition. Refer to Testing
for intermittent and Poor Connections in Diagrams.
^ Inspect the circuit wiring for an intermittent condition. Refer to Testing for Electrical Intermittents in Diagrams.
^ Extended cranking with a low battery could set DTC P0748.

TEST DESCRIPTION
The numbers below refer to the step numbers on the diagnostic table.
2. This step verifies that the fault is present.
3. This step tests the transmission wiring harness and the PC solenoid valve for correct resistance.
9. This step begins diagnosis of the engine side of the circuit.

P0751

Diagnostic Chart
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 450
Chevrolet Venture V6-3.4L VIN E 2130

Schematic

Circuit Description with 4T65-E Automatic Transaxle


The 1-2, 3-4 shift solenoid (1-2, 3-4 SS) valve is supplied with ignition voltage by a fused circuit. The ground path is provided by the PCM,
depending on the commanded state of the solenoid. When the PCM commands the solenoid OFF, a ground path is not provided and the filtered
line pressure that is fed to the solenoid is exhausted. When the PCM commands the solenoid ON, a ground path is provided and the exhaust port
is blocked, slopping the exhaust of line pressure.

The PCM identifies a 1-2, 3-4 SS valve condition by monitoring the commanded gear versus gear ratio.

If the PCM detects a 2nd gear ratio when 1st gear is commanded and a 3rd gear ratio when 4th gear is commanded, then DTC P0751 sets. DTC
P0751 is a type B DTC.

CONDITIONS FOR RUNNING THE DTC


^ No TP sensor DTC P0121, P0122 or P0123.
^ No VSS DTC P0502 or P0503.
^ No AT ISS sensor DTC P0716 or P0717.
^ No transmission slipping DTC P0730.
^ No 1-2, 3-4 SS valve electrical DTC P0753.
^ No 2-3 shift SS electrical DTC P0758.
^ No TFP manual valve position switch DTC P1810.
^ No torque converter overstress DTC P1814.
^ No TCC PWM solenoid valve DTC P1860.
^ The system voltage is 8-18 volts.
^ The engine speed is greater than 500 RPM for 5 seconds and not in fuel shut off.
^ The transmission is not in PARK, NEUTRAL or REVERSE.
^ The vehicle speed is greater than 8 km/h (5 mph).
^ The TP angle is greater than 10%.
^ The transmission fluid temperature is between 20°C (68°F) and 129°C (264°F).
^ The engine torque is 27-270 N.m (20-200 lb ft).
^ The Transmission ISS is 150-8000 RPM.
^ The Transmission OSS is greater than 300 RPM.
^ The time since the last gear range change is greater than 1 second.

CONDITIONS FOR SETTING THE DTC


The following conditions both occur twice in one trip:

Condition 1
The PCM commands 1st gear and the gear ratio indicates 2nd gear (1.52:1 to 1.62:1) for 1 second.

Condition 2
The PCM commands 4th gear and the gear ratio indicates 3rd gear (0.95:1 to 1.05:1) for 1 second.

ACTION TAKEN WHEN THE DTC SETS


^ The PCM illuminates the Malfunction Indicator Lamp (MIL) during the second consecutive trip in which the conditions for setting the DTC
are met.
^ The PCM commands maximum line pressure.
^ The PCM freezes shift adapts.
^ The PCM records the operating conditions when the Conditions for Setting the DTC are met. The PCM stores this information as Freeze
Frame and Failure Records.
^ The PCM stores DTC P0751 in PCM history during the second consecutive trip in which the conditions for setting the DTC are met.

CONDITIONS FOR CLEARING THE MIL/DTC


^ The PCM turns OFF the MIL during the third consecutive trip in which the diagnostic test runs and passes.
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 451
Chevrolet Venture V6-3.4L VIN E 2131
^ A scan tool can clear the MIL/DTC.
^ The PCM clears the DTC from the PCM history if the vehicle completes 40 consecutive warm-up cycles without an emission-related
diagnostic fault occurring.
^ The PCM cancels the DTC default actions when the fault no longer exists and the ignition switch is OFF long enough in order to power down
the PCM.

DIAGNOSTIC AIDS
^ Inspect the transmission fluid for sediment.
^ Inspect the transmission filter for debris.
^ Ensure that the scan tool commanded gear has correct solenoid states and ratio. Refer to the Shift Solenoid Valve State and Gear Ratio table.

TEST DESCRIPTION

IMPORTANT: Do not drive the vehicle for an extended period of time because additional internal damage may occur.

The numbers below refer to the step numbers on the diagnostic table.
3. This step confirms that the PCM commanded all the shifts, but all the shifts did not occur.
P0752

Diagnostic Chart
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 452
Chevrolet Venture V6-3.4L VIN E 2132

Schematic

Circuit Description with 4T65-E Automatic Transaxle


The 1-2, 3-4 shift solenoid (1-2, 3-4 SS) valve is supplied with ignition voltage by a fused circuit. The ground path is provided by the PCM,
depending on the commanded state of the solenoid. When the PCM commands the solenoid OFF, a ground path is not provided and the filtered
line pressure that is fed to the solenoid is exhausted. When the PCM commands the solenoid ON, a ground path is provided and the exhaust port
is blocked, stopping the exhaust of line pressure.

The PCM identifies a 1-2, 3-4 SS valve condition by monitoring the commanded gear versus gear ratio.

If the PCM detects a 1st gear ratio when 2nd gear is commanded and a 4th gear ratio when 3rd gear is commanded, then DTC P0752 sets. DTC
P0752 is a type B DTC.

CONDITIONS FOR RUNNING THE DTC


^ No TP sensor DTC P0121, P0122 or P0123.
^ No VSS DTC P0502 or P0503.
^ No AT ISS sensor DTC P0716 or P0717.
^ No transmission slipping DTC P0730.
^ No 1-2, 3-4 SS valve electrical DTC P0753.
^ No 2-3 shift SS electrical DTC P0758.
^ No TFP manual valve position switch DTC P1810.
^ No torque converter overstress DTC P1814.
^ No TCC PWM solenoid valve DTC P1860.
^ The system voltage is 8-18 volts.
^ The engine speed is greater than 500 RPM for 5 seconds and not in fuel shut off.
^ The transmission is not in PARK, NEUTRAL or REVERSE.
^ The vehicle speed is greater than 8 km/h (5 mph).
^ The TP angle is greater than 10%.
^ The transmission fluid temperature is between 20°C (68°F) and 129°C (264°F).
^ The engine torque is 27-270 N.m (20-200 lb ft).
^ The Transmission ISS is 150-8000 RPM.
^ The Transmission OSS is greater than 300 RPM.
^ The time since the last gear range change is greater than 1 second.

CONDITIONS FOR SETTING THE DTC


The following conditions both occur twice in one trip:

Condition 1
The PCM commands 2nd gear and the gear ratio indicates 1st gear (2.87:1 to 2.97:1) for 1 second.

Condition 2
The PCM commands 3rd gear and the gear ratio indicates 4th gear (0.65:1 to 0.75:1) for 1 second.

ACTION TAKEN WHEN THE DTC SETS


^ The PCM illuminates the Malfunction Indicator Lamp (MIL) during the second consecutive trip in which the conditions for setting the DTC
are met.
^ The PCM commands maximum line pressure.
^ The PCM freezes shift adapts.
^ The PCM inhibits 3-2 downshifts when the vehicle speed is greater than 48 km/h (30 mph).
^ The PCM records the operating conditions when the Conditions for Setting the DTC are met. The PCM stores this information as Freeze
Frame and Failure Records.
^ The PCM stores DTC P0752 in PCM history during the second consecutive trip in which the conditions for setting the DTC are met.
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 453
Chevrolet Venture V6-3.4L VIN E 2133

CONDITIONS FOR CLEARING THE MIL/DTC


^ The PCM turns OFF the MIL during the third consecutive trip in which the diagnostic test runs and passes.
^ A scan tool can clear the MIL/DTC.
^ The PCM clears the DTC from the PCM history if the vehicle completes 40 consecutive warm-up cycles without an emission-related
diagnostic fault occurring.
^ The PCM cancels the DTC default actions when the fault no longer exists and the ignition switch is OFF long enough in order to power down
the PCM.

DIAGNOSTIC AIDS
^ Inspect the transmission fluid for sediment.
^ Inspect the transmission filter for debris.
^ Ensure that the scan tool commanded gear has correct solenoid states and ratio. Refer to the Shift Solenoid Valve State and Gear Ratio table.

TEST DESCRIPTION

IMPORTANT: Do not drive the vehicle for an extended period of time because additional internal damage may occur.

The numbers below refer to the step numbers on the diagnostic table.
3. This step confirms that the PCM commanded all the shifts, but all the shifts did not occur.
P0753

Diagnostic Chart 1 Of 3
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 454
Chevrolet Venture V6-3.4L VIN E 2134

Diagnostic Chart 2 Of 3
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 455
Chevrolet Venture V6-3.4L VIN E 2135

Diagnostic Chart 3 Of 3

Schematic
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 456
Chevrolet Venture V6-3.4L VIN E 2136

Circuit Description with 4T65-E Automatic Transaxle


The 1-2, 3-4 shift solenoid (1-2, 3-4 SS) valve controls transmission fluid pressure acting on the 1-2 and 3-4 shift valves to position the valves
for the appropriate gear. The 1-2, 3-4 SS valve is a normally-open exhaust valve located on the control valve body. A fused circuit supplies
ignition voltage to the 1-2, 3-4 SS valve. The output driver module, within the PCM, commands the solenoid ON or OFF by switching the
ground path. When the 1-2, 3-4 SS valve is commanded ON, the PCM senses low voltage. When the 1-2, 3-4 SS valve is commanded OFF, the
PCM senses high voltage.

If the PCM detects a continuous open, short to ground or short to power in the 1-2, 3-4 SS valve circuit, then DTC P0753 sets. DTC P0753 is a
type B DTC.

CONDITIONS FOR RUNNING THE DTC


^ The system voltage is 9-18 volts.
^ The engine speed is greater than 500 RPM for 5 seconds and not in fuel shut off.

CONDITIONS FOR SETTING THE DTC


DTC P0753 sets when one of the following conditions occurs for 5 seconds:

Condition 1
The PCM commands the solenoid ON and voltage feedback remains high (B+).

Condition 2
The PCM commands the solenoid OFF, and the voltage feedback remains low (0 volts).

ACTION TAKEN WHEN THE DTC SETS


^ The PCM illuminates the Malfunction Indicator Lamp (MIL) during the second consecutive trip in which the conditions for setting the DTC
are met.
^ The PCM commands maximum line pressure.
^ The PCM inhibits TCC.
^ The PCM freezes shift adapts.
^ The PCM inhibits 3-2 downshifts when the vehicle speed is greater than 48 km/h (30 mph).
^ The PCM records the operating conditions when the Conditions for Setting the DTC are met. The PCM stores this information as Freeze
Frame and Failure Records.
^ The PCM stores DTC P0753 in PCM history during the second consecutive trip in which the conditions for setting the DTC are met.

CONDITIONS FOR CLEARING THE MIL/DTC


^ The PCM turns OFF the MIL during the third consecutive trip in which the diagnostic test runs and passes.
^ A scan tool can clear the MIL/DTC.
^ The PCM clears the DTC from the PCM history if the vehicle completes 40 consecutive warm-up cycles without an emission-related
diagnostic fault occurring.
^ The PCM cancels the DTC default actions when the fault no longer exists and the ignition switch is OFF long enough in order to power down
the PCM.

DIAGNOSTIC AIDS
^ Inspect the connectors at the controller, the component and all other circuit connecting points for an intermittent condition. Refer to Testing
for Intermittent and Poor Connections in Diagrams.
^ Inspect the circuit wiring for an intermittent condition. Refer to Testing for Electrical Intermittents in Diagrams.
^ Ensure that the scan tool commanded gear has correct solenoid states and ratio. Refer to the Shift Solenoid Valve State and Gear Ratio table.

TEST DESCRIPTION
The numbers below refer to the step numbers on the diagnostic table.
2. A short to ground in the power feed circuit to the solenoid ahead of the splice would open the fuse and set DTCs for other solenoids on the
same circuit. An open in the same circuit would not open the fuse but, would set the other DTCs.
P0756
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 457
Chevrolet Venture V6-3.4L VIN E 2137

Diagnostic Chart
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 458
Chevrolet Venture V6-3.4L VIN E 2138

Schematic

Circuit Description with 4T65-E Automatic Transaxle


The 2-3 shift solenoid (2-3 SS) valve is supplied with fused ignition voltage. The ground path is provided by the PCM, depending on the
commanded state of the solenoid. When the PCM commands the solenoid OFF, a ground path is not provided and the filtered line pressure that is
fed to the solenoid is exhausted. When the PCM commands the solenoid ON, a ground path is provided and the exhaust port is blocked, stopping
the exhaust of line pressure.

The PCM identifies a 2-3 SS valve performance condition by monitoring the commanded gear versus the gear ratio.

If the PCM detects a 4th gear ratio when 1st gear is commanded and a 3rd gear ratio when 2nd gear is commanded, then DTC P0756 sets. DTC
P0756 is a type A DTC.

CONDITIONS FOR RUNNING THE DTC


^ No TP sensor DTC P0121, P0122 or P0123.
^ No VSS DTC P0502 or P0503.
^ No AT ISS sensor DTC P0716 or P0717.
^ No transmission slipping DTC P0730.
^ No 1-2, 3-4 SS valve electrical DTC P0753.
^ No 2-3 SS valve electrical DTC P0758.
^ No TFP manual valve position switch DTC P1810.
^ No torque converter overstress DTC P1814.
^ No TCC PWM solenoid valve DTC P1860.
^ The system voltage is 8-18 volts.
^ The engine speed is greater than 500 RPM for 5 seconds and not in fuel shut off.
^ The engine torque is 27-270 N.m (20-200 lb ft).
^ The transmission fluid temperature is between 20°C (68°F) and 129°C (264°F).
^ The transmission is not in PARK, NEUTRAL or REVERSE.
^ The vehicle speed is greater than 8 km/h (5 mph).
^ The TP angle is greater than 10%.
^ The Transmission ISS is 150-8000 RPM.
^ The Transmission OSS is greater than 300 RPM.
^ The time since the last gear range change is greater than 1 second.

CONDITIONS FOR SETTING THE DTC


The following conditions both occur twice in one trip:

Condition 1
The PCM commands 1st gear and the gear ratio indicates 4th gear (0.65:1 to 0.75:1) for 1 second.

Condition 2
The PCM commands 2nd gear and the gear ratio indicates 3rd gear (0.95:1 to 1.05:1) for 1 second.
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 459
Chevrolet Venture V6-3.4L VIN E 2139

ACTION TAKEN WHEN THE DTC SETS


^ The PCM illuminates the Malfunction Indicator Lamp (MIL).
^ The PCM commands 3rd gear.
^ The PCM commands maximum line pressure.
^ The PCM freezes shift adapts.
^ The PCM records the operating conditions when the Conditions for Setting the DTC are met. The PCM stores this information as Freeze
Frame and Failure Records.
^ The PCM stores DTC P0756 in PCM history.

CONDITIONS FOR CLEARING THE MIL/DTC


^ The PCM turns OFF the MIL during the third consecutive trip in which the diagnostic test runs and passes.
^ A scan tool can clear the MIL/DTC.
^ The PCM clears the DTC from the PCM history if the vehicle completes 40 consecutive warm-up cycles without an emission-related
diagnostic fault occurring.
^ The PCM cancels the DTC default actions when the fault no longer exists and the ignition switch is OFF long enough in order to power down
the PCM.

DIAGNOSTIC AIDS
^ Inspect the transmission fluid for sediment.
^ Inspect the transmission filter for debris.
^ Ensure that the scan tool commanded gear has correct solenoid states and ratio. Refer to the Shift Solenoid Valve State and Gear Ratio table.

TEST DESCRIPTION
The numbers below refer to the step numbers on the diagnostic table.

IMPORTANT: Do not drive the vehicle for an extended period of time, as additional internal damage may occur.

3. This step confirms that the PCM commanded all the shifts, but all the shifts did not occur.

P0757
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 460
Chevrolet Venture V6-3.4L VIN E 2140

Diagnostic Chart
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 461
Chevrolet Venture V6-3.4L VIN E 2141

Schematic

Circuit Description with 4T65-E Automatic Transaxle


The 2-3 shift solenoid (2-3 SS) valve is supplied with fused ignition voltage. The ground path is provided by the PCM, depending on the
commanded state of the solenoid. When the PCM commands the solenoid OFF, a ground path is not provided and the filtered line pressure that is
fed to the solenoid is exhausted. When the PCM commands the solenoid ON, a ground path is provided and the exhaust port is blocked, stopping
the exhaust of line pressure.

The PCM identifies a 2-3 SS valve performance condition by monitoring the commanded gear versus the gear ratio.

If the PCM detects a 2nd gear ratio when 3rd gear is commanded and a 1st gear ratio when 4th gear is commanded, then DTC P0757 sets. DTC
P0757 is a type A DTC.

CONDITIONS FOR RUNNING THE DTC


^ No TP sensor DTC P0121, P0122 or P0123.
^ No VSS DTC P0502 or P0503.
^ No AT ISS sensor DTC P0716 or P0717.
^ No transmission slipping DTC P0730.
^ No 1-2, 3-4 SS valve electrical DTC P0753.
^ No 2-3 SS valve electrical DTC P0758.
^ No TFP manual valve position switch DTC P1810.
^ No torque converter overstress DTC P1814.
^ No TCC PWM solenoid valve DTC P1860.
^ The system voltage is 8-18 volts.
^ The engine speed is greater than 500 RPM for 5 seconds and not in fuel shut off.
^ The engine torque is 27-270 N.m (20-200 lb ft).
^ The transmission fluid temperature is between 20°C (68°F) and 129°C (264°F).
^ The transmission is not in PARK, NEUTRAL or REVERSE.
^ The vehicle speed is greater than 8 km/h (5 mph).
^ The TP angle is greater than 10%.
^ The Transmission ISS is 150-8000 RPM.
^ The Transmission OSS is greater than 300 RPM.
^ The time since the last gear range change is greater than 1 second.

CONDITIONS FOR SETTING THE DTC


The following conditions both occur twice in one trip:

Condition 1
The PCM commands 3rd gear and the gear ratio indicates 2nd gear (1.52:1 to 1.62:1) for 1 second.

Condition 2
The PCM commands 4th gear and the gear ratio indicates 1st gear (2.87:1 to 2.97:1) for 1 second.
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 462
Chevrolet Venture V6-3.4L VIN E 2142

ACTION TAKEN WHEN THE DTC SETS


^ The PCM illuminates the Malfunction Indicator Lamp (MIL).
^ The PCM commands maximum line pressure.
^ The PCM inhibits TCC.
^ The PCM inhibits 4th gear.
^ The PCM freezes shift adapts.
^ The PCM records the operating conditions when the Conditions for Setting the DTC are met. The PCM stores this information as Freeze
Frame and Failure Records.
^ The PCM stores DTC P0757 in PCM history.

CONDITIONS FOR CLEARING THE MIL/DTC


^ The PCM turns OFF the MIL during the third consecutive trip in which the diagnostic test runs and passes.
^ A scan tool can clear the MIL/DTC.
^ The PCM clears the DTC from the PCM history if the vehicle completes 40 consecutive warm-up cycles without an emission-related
diagnostic fault occurring.
^ The PCM cancels the DTC default actions when the fault no longer exists and the ignition switch is OFF long enough in order to power down
the PCM.

DIAGNOSTIC AIDS
^ Inspect the transmission fluid for sediment.
^ Inspect the transmission filter for debris.
^ Ensure that the scan tool commanded gear has correct solenoid states and ratio. Refer to the Shift Solenoid Valve State and Gear Ratio table.

TEST DESCRIPTION
The numbers below refer to the step numbers on the diagnostic table.

IMPORTANT: Do not drive the vehicle for an extended period of time, as additional internal damage may occur.

3. This step confirms that the PCM commanded all the shifts, but all the shifts did not occur.

P0758

Diagnostic Chart 1 Of 3
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 463
Chevrolet Venture V6-3.4L VIN E 2143

Diagnostic Chart 2 Of 3
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 464
Chevrolet Venture V6-3.4L VIN E 2144

Diagnostic Chart 3 Of 3
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 465
Chevrolet Venture V6-3.4L VIN E 2145
Schematic

Circuit Description with 4T65-E Automatic Transaxle


The 2-3 shift solenoid (2-3 SS) valve controls transmission fluid pressure acting on the 1-2 and 2-3 shift valves to position the valves for the
appropriate gear. The 2-3 SS valve is a normally-open exhaust valve located on the control valve body. A fused circuit supplies ignition voltage
to the 2-3 SS valve. The output driver module, within the PCM, commands the solenoid ON or OFF by switching the ground path. When the 2-3
SS valve is commanded ON, the PCM senses low voltage. When the 2-3 SS valve is commanded OFF, the PCM senses high voltage.

If the PCM detects a continuous open, short to ground or short to power in the 2-3 SS valve circuit, then DTC P0758 sets. DTC P0758 is a type
A DTC.

CONDITIONS FOR RUNNING THE DTC


^ The system voltage is 9-18 volts.
^ The engine speed is greater than 500 RPM for 5 seconds and not in fuel shut off.

CONDITIONS FOR SETTING THE DTC


DTC P0758 sets when one of the following conditions occurs for 5 seconds:

Condition 1
The PCM commands the solenoid ON and the voltage feedback remains high (B+).

Condition 2
The PCM commands the solenoid OFF and the voltage feedback remains low (0 volts).

ACTION TAKEN WHEN THE DTC SETS


^ The PCM illuminates the Malfunction Indicator Lamp (MIL).
^ The PCM commands 3rd gear.
^ The PCM commands maximum line pressure.
^ The PCM inhibits TCC.
^ The PCM freezes shift adapts.
^ The PCM records the operating conditions when the Conditions for Setting the DTC are met. The PCM stores this information as Freeze
Frame and Failure Records.
^ The PCM stores DTC P0758 in PCM history.

CONDITIONS FOR CLEARING THE MIL/DTC


^ The PCM turns OFF the MIL during the third consecutive trip in which the diagnostic test runs and passes.
^ A scan tool can clear the MIL/DTC.
^ The PCM clears the DTC from the PCM history if the vehicle completes 40 consecutive warm-up cycles without an emission-related
diagnostic fault occurring.
^ The PCM cancels the DTC default actions when the fault no longer exists and the ignition switch is OFF long enough in order to power down
the PCM.

DIAGNOSTIC AIDS
^ Inspect the connectors at the controller, the component and all other circuit connecting points for an intermittent condition. Refer to Testing
for Intermittent and Poor Connections in Diagrams.
^ Inspect the circuit wiring for an intermittent condition. Refer to Testing for Electrical Intermittents in Diagrams.
^ Ensure that the scan tool commanded gear has correct solenoid states and ratio. Refer to the Shift Solenoid Valve State and Gear Ratio table.

TEST DESCRIPTION
The numbers below refer to the step numbers on the diagnostic table.
2. A short to ground in the power feed circuit to the solenoid ahead of the splice would open the fuse and set DTCs for other solenoids on the
same circuit. An open in the same circuit would not open the fuse but, would set the other DTCs.

P1106
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 466
Chevrolet Venture V6-3.4L VIN E 2146

Diagnostic Chart

Schematic

CIRCUIT DESCRIPTION
The Manifold Absolute Pressure (MAP) sensor responds to changes in intake manifold pressure (vacuum). The MAP sensor signal voltage to the
PCM varies from below 2 volts at idle (high vacuum) to above 4 volts with the key ON, engine not running or at wide-open throttle (low
vacuum). The MAP sensor is used to determine manifold pressure changes while the EGR flow test diagnostic is being run, refer to DTC P0401
Exhaust Gas Recirculation (EGR) Flow Insufficient. See: Diagnostic Trouble Code Tests and Associated Procedures/P Code Charts/P0401

Also to update the Barometric Pressure Reading (BARO), as an enabling factor for other diagnostics. The PCM monitors the MAP signals for
voltages outside the normal range of the MAP sensor. If the PCM detects a MAP signal voltage that is intermittently high, DTC P1106 will set.
See: Diagnostic Trouble Code Tests and Associated Procedures/P Code Charts/P1106

CONDITIONS FOR RUNNING THE DTC


- TP sensor DTCs are not present.
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 467
Chevrolet Venture V6-3.4L VIN E 2147
- System voltage is more than 9.0 volts.
- Engine has been running for a length of time that is determined by start-up coolant temperature. The length of time ranges from 2 minutes at
less than -30°C (-22°F) to 0.5 second at more than 30°C (86°F).
- Throttle position is below 2 percent if the engine speed is less than 3000 RPM
- Throttle position is above 30 percent if the engine speed is more than 3000 RPM.

CONDITIONS FOR SETTING THE DTC


The MAP sensor intermittently indicates a voltage more than 4.3 volts.

ACTION TAKEN WHEN THE DTC SETS


- The PCM will not illuminate the Malfunction Indicator Lamp (MIL).
- The PCM will store conditions which were present when the DTC set as Failure Records data only. This information will not be stored as
Freeze Frame data.

CONDITIONS FOR CLEARING THE MIL/DTC


- A History DTC will clear after 40 consecutive warm-up cycles have occurred without a malfunction.
- The DTC can be cleared by using a scan tool.

DIAGNOSTIC AIDS
Inspect for the following conditions:

IMPORTANT: Remove any debris from the connector surfaces before servicing a component. Inspect the connector gaskets when diagnosing
or replacing a component. Ensure that the gaskets are installed correctly. The gaskets prevent contaminate intrusion.

- Poor terminal connection-Inspect the harness connectors for backed out terminals, improper mating, broken locks, improperly formed or
damaged terminals, and faulty terminal to wire connection. Use a corresponding mating terminal to test for proper tension. Refer to
Diagrams.
- Damaged harness-Inspect the wiring harness for damage. If the harness inspection does not reveal a problem, observe the display on the scan
tool while moving connectors and wiring harnesses related to the sensor. A change in the scan tool display may indicate the location of the
fault. Refer to Diagrams.
- PCM and engine grounds for clean and secure connections

If the DTC is determined to be intermittent, reviewing the Failure Records can be useful in determining when the DTC was last set.

P1107
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 468
Chevrolet Venture V6-3.4L VIN E 2148

Diagnostic Chart

Schematic

CIRCUIT DESCRIPTION
The Manifold Absolute Pressure (MAP) sensor responds 10 changes in intake manifold pressure (vacuum). The MAP sensor signal voltage to
the PCM varies from below 2 volts at idle (high vacuum) to above 4 volts with the key ON, engine not running or at wide-open throttle (low
vacuum). The MAP sensor is used to determine manifold pressure changes while the EGR flow test diagnostic is being run, refer to DTC P0401
Exhaust Gas Recirculation (EGR) Flow Insufficient. See: Diagnostic Trouble Code Tests and Associated Procedures/P Code Charts/P0401

Also to update the Barometric Pressure Reading (BARO), as an enabling factor for other diagnostics. The PCM monitors the MAP signals for
voltages outside the normal range of the MAP sensor. If the PCM detects a MAP signal voltage that is intermittently low, DTC P1107 will set.
See: Diagnostic Trouble Code Tests and Associated Procedures/P Code Charts/P1107
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 469
Chevrolet Venture V6-3.4L VIN E 2149

CONDITIONS FOR RUNNING THE DTC


- TP sensor DTCs are not present.
- System voltage more than 9 volts.
- The engine is running.
- Throttle angle is above 0 percent, if engine speed is less than 1000 RPM.
- Throttle angle is above 10 percent, if engine speed is more than 1000 RPM.

CONDITIONS FOR SETTING THE DTC


The MAP sensor intermittently indicates a voltage below 0.1 volt (12 kPa).

ACTION TAKEN WHEN THE DTC SETS


- The PCM will not illuminate the malfunction indicator lamp (MIL).
- The PCM will store conditions which were present when the DTC set as Failure Records data only. This information will not be stored as
Freeze Frame data.

CONDITIONS FOR CLEARING THE MIL/DTC


- A History DTC will clear after 40 consecutive warm-up cycles have occurred without a malfunction.
- The DTC can be cleared by using a scan tool.

DIAGNOSTIC AIDS
Inspect for the following conditions:

IMPORTANT: Remove any debris from the connector surfaces before servicing a component. Inspect the connector gaskets when diagnosing
or replacing a component. Ensure that the gaskets are installed correctly. The gaskets prevent contaminate intrusion.

- Poor terminal connection-Inspect the harness connectors for backed out terminals, improper mating, broken locks, improperly formed or
damaged terminals, and faulty terminal to wire connection. Use a corresponding mating terminal to test for proper tension. Refer to
Diagrams.
- Damaged harness-Inspect the wiring harness for damage. If the harness inspection does not reveal a problem, observe the display on the scan
tool while moving connectors and wiring harnesses related to the sensor. A change in the scan tool display may indicate the location of the
fault. Refer to Diagrams.
- PCM and engine grounds for clean and secure connections

If the DTC is determined to be intermittent, reviewing the Failure Records can be useful in determining when the DTC was last set.

P1111
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 470
Chevrolet Venture V6-3.4L VIN E 2150

Diagnostic Chart

Schematic

CIRCUIT DESCRIPTION
The Intake Air Temperature (IAT) sensor is a thermistor which measures the temperature of the air entering the engine. The PCM applies 5.0
volts through a pull up resistor to the IAT sensor. When the intake air is cold, the sensor resistance is high and the PCM will monitor a high
signal voltage on the IAT signal circuit. If the intake air is warm, the sensor resistance is lower causing the PCM to monitor a lower voltage.
DTC P1111 will set when the PCM detects an intermittently high signal voltage on the intake air temperature sensor signal circuit.

CONDITIONS FOR RUNNING THE DTC


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 471
Chevrolet Venture V6-3.4L VIN E 2151
- Active ECT, MAF sensor or VSS DTC are not present.
- Vehicle speed is less than 56 km/h (35 mph).
- MAF is less than 12 gm/s.
- ECT is more than 60°C (140°F).
- The Engine run time is more than 3 minutes.

CONDITIONS FOR SETTING THE DTC


- IAT signal voltage indicates an intake air temperature intermittently less than -37°C (-35°F).
- The conditions is present for up to 5 seconds.

ACTION TAKEN WHEN THE DTC SETS


- The PCM will not illuminate the Malfunction Indicator Lamp (MIL).
- The PCM will store conditions which were present when the DTC set as Failure Records data only. This information will not be stored as
Freeze Frame data.

CONDITIONS FOR CLEARING THE MIL/DTC


- A History DTC will clear after 40 consecutive warm-up cycles have occurred without a malfunction.
- The DTC can be cleared by using a scan tool.

DIAGNOSTIC AIDS
The following could cause an intermittent condition:

IMPORTANT: Remove any debris from the connector surfaces before servicing a component. Inspect the connector gaskets when diagnosing
or replacing a component. Ensure that the gaskets are installed correctly. The gaskets prevent contaminate intrusion.

- Poor terminal connection-Inspect the harness connectors for backed out terminals, improper mating, broken locks, improperly formed or
damaged terminals, and faulty terminal to wire connection. Use a corresponding mating terminal to test for proper tension. Refer to
Diagrams.
- Damaged harness-Inspect the wiring harness for damage. If the harness inspection does not reveal a problem, observe the display on the scan
tool while moving connectors and wiring harnesses related to the sensor. A change in the scan tool display may indicate the location of the
fault. Refer to Diagrams.
- PCM and engine grounds for clean and secure connections

If the DTC is determined to be intermittent, reviewing the Failure Records can be useful in determining when the DTC was last set.

P1112

Diagnostic Chart
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 472
Chevrolet Venture V6-3.4L VIN E 2152

Schematic

CIRCUIT DESCRIPTION
The Intake Air Temperature (IAT) sensor is a thermistor which measures the temperature of the air entering the engine. The PCM applies 5.0
volts through a pull up resistor to the IAT sensor. When the intake air is cold, the sensor resistance is high and the PCM will monitor a high
signal voltage on the IAT signal circuit. If the intake air is warm, the sensor resistance is lower causing the PCM to monitor a lower voltage.
DTC P1112 will set when the PCM detects an intermittently low signal voltage on the intake air temperature sensor signal circuit.

CONDITIONS FOR RUNNING THE DTC


- Active ECT, MAF sensor, VSS DTCs are not present.
- The engine has been running for over 10 seconds.
- Vehicle speed is more than 25 mph.

CONDITIONS FOR SETTING THE DTC


- The IAT sensor indicates an intake air temperature intermittently more than 135°C (275°F).
- The conditions is present for up to 5 seconds.

ACTION TAKEN WHEN THE DTC SETS


- The PCM will not illuminate the Malfunction Indicator Lamp (MIL).
- The PCM will store conditions which were present when the DTC set as Failure Records data only. This information will not be stored as
Freeze Frame data.

CONDITIONS FOR CLEARING THE MIL/DTC


- A History DTC will clear after 40 consecutive warm-up cycles have occurred without a malfunction.
- The DTC can be cleared by using a scan tool.

DIAGNOSTIC AIDS
The following could cause an intermittent condition:

IMPORTANT: Remove any debris from the connector surfaces before servicing a component. Inspect the connector gaskets when diagnosing
or replacing a component. Ensure that the gaskets are installed correctly. The gaskets prevent contaminate intrusion.

- Poor terminal connection-Inspect the harness connectors for backed out terminals, improper mating, broken locks, improperly formed or
damaged terminals, and faulty terminal to wire connection. Use a corresponding mating terminal to test for proper tension. Refer to
Diagrams.
- Damaged harness-Inspect the wiring harness for damage. If the harness inspection does not reveal a problem, observe the display on the scan
tool while moving connectors and wiring harnesses related to the sensor. A change in the scan tool display may indicate the location of the
fault. Refer to Diagrams.
- PCM and engine grounds for clean and secure connections

If the DTC is determined to be intermittent, reviewing the Failure Records can be useful in determining when the DTC was last set.

P1114
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 473
Chevrolet Venture V6-3.4L VIN E 2153

Diagnostic Chart

Schematic

CIRCUIT DESCRIPTION
The Engine Coolant Temperature (ECT) sensor is a thermistor mounted in the engine coolant stream. The PCM applies a voltage (about 5.0
volts) through a pull up resistor to the ECT signal circuit. When the engine coolant is cold, the sensor (thermistor) resistance is high therefore the
PCM will measure a high signal voltage. As the engine coolant warms, the sensor resistance becomes less, and the ECT signal voltage measured
at the PCM drops. With a fully warmed up engine, the ECT signal voltage should measure about 1.5 to 2.0 volts. If the PCM detects an ECT
signal that is intermittently below the range of the ECT sensor, DTC P1114 will set.

CONDITIONS FOR RUNNING THE DTC


The engine is running for 3 seconds.

CONDITIONS FOR SETTING THE DTC


- The ECT sensor is intermittently more than 140°C (283°F)
- The condition is present for at least 3 seconds.

ACTION TAKEN WHEN THE DTC SETS


- The PCM will not illuminate the malfunction indicator lamp (MIL).
- The PCM will store conditions which were present when the DTC set as Failure Records data only. This information will not be stored as
Freeze Frame data.

CONDITIONS FOR CLEARING THE MIL/DTC


- A History DTC will clear after 40 consecutive warm-up cycles have occurred without a malfunction.
- The DTC can be cleared by using a scan tool.

DIAGNOSTIC AIDS
The following could cause an intermittent condition:

IMPORTANT: Remove any debris from the connector surfaces before servicing a component. Inspect the connector gaskets when diagnosing
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 474
Chevrolet Venture V6-3.4L VIN E 2154
or replacing a component. Ensure that the gaskets are installed correctly. The gaskets prevent contaminate intrusion.

- Poor terminal connection-Inspect the harness connectors for backed out terminals, improper mating, broken locks, improperly formed or
damaged terminals, and faulty terminal to wire connection. Use a corresponding mating terminal to test for proper tension. Refer to
Diagrams.
- Damaged harness-Inspect the wiring harness for damage. If the harness inspection does not reveal a problem, observe the display on the scan
tool while moving connectors and wiring harnesses related to the sensor. A change in the scan tool display may indicate the location of the
fault. Refer to Diagrams.
- PCM and engine grounds for clean and secure connections

If the DTC is determined to be intermittent, reviewing the Failure Records can be useful in determining when the DTC was last set.

P1115

Diagnostic Chart
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 475
Chevrolet Venture V6-3.4L VIN E 2155

Schematic

CIRCUIT DESCRIPTION
The Engine Coolant Temperature (ECT) sensor is a thermistor mounted in the engine coolant stream. The PCM applies a voltage (about 5.0
volts) through a pull up resistor to the ECT signal circuit. When the engine coolant is cold, the sensor (thermistor) resistance is high. Therefore
the PCM will measure a high signal voltage. As the engine coolant warms, the sensor resistance becomes less, and the ECT signal voltage
measured at the PCM drops. With a fully warmed up engine, the ECT signal voltage should measure about 1.5 to 2.0 volts. If the PCM detects an
ECT signal that is intermittently above the range of the ECT sensor, DTC P1115 will set.

CONDITIONS FOR RUNNING THE DTC


The engine is running for 15 seconds.

CONDITIONS FOR SETTING THE DTC


- The ECT sensor is intermittently less than -39°C (-37°F)
- Above conditions present for longer than 3 seconds.

ACTION TAKEN WHEN THE DTC SETS


- The PCM will not illuminate the Malfunction Indicator Lamp (MIL).
- The PCM will store conditions which were present when the DTC set as Failure Records data only. This information will not be stored as
Freeze Frame data.

CONDITIONS FOR CLEARING THE MIL/DTC


- A History DTC will clear after 40 consecutive warm-up cycles have occurred without a malfunction.
- The DTC can be cleared by using a scan tool.

DIAGNOSTIC AIDS
The following could cause an intermittent condition:

IMPORTANT: Remove any debris from the connector surfaces before servicing a component. Inspect the connector gaskets when diagnosing
or replacing a component. Ensure that the gaskets are installed correctly. The gaskets prevent contaminate intrusion.

- Poor terminal connection-Inspect the harness connectors for backed out terminals, improper mating, broken locks, improperly formed or
damaged terminals, and faulty terminal to wire connection. Use a corresponding mating terminal to test for proper tension. Refer to
Diagrams.
- Damaged harness-Inspect the wiring harness for damage. If the harness inspection does not reveal a problem, observe the display on the scan
tool while moving connectors and wiring harnesses related to the sensor. A change in the scan tool display may indicate the location of the
fault. Refer to Diagrams.
- PCM and engine grounds for clean and secure connections

If the DTC is determined to be intermittent, reviewing the Failure Records can be useful in determining when the DTC was last set.

P1121
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 476
Chevrolet Venture V6-3.4L VIN E 2156

Diagnostic Chart
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 477
Chevrolet Venture V6-3.4L VIN E 2157

Schematic

CIRCUIT DESCRIPTION
The Throttle Position (TP) sensor circuit provides a voltage signal that changes relative to throttle blade angle. The signal voltage will vary from
below 1.0 volt at closed throttle to above 4.0 volts at Wide Open Throttle (WOT). If the PCM detects a TP signal voltage that is intermittently
more than the range of the TP sensor, DTC P1121 will be set.

CONDITIONS FOR RUNNING THE DTC


The ignition is ON.

CONDITIONS FOR SETTING THE DTC


TP sensor intermittently indicates a throttle position signal more than 4.9 volts.

ACTION TAKEN WHEN THE DTC SETS


- The PCM will not illuminate the Malfunction Indicator Lamp (MIL).
- The PCM will store conditions which were present when the DTC set as Failure Records data only. This information will not be stored as
Freeze Frame data.

CONDITIONS FOR CLEARING THE MIL/DTC


- A History DTC will clear after 40 consecutive warm-up cycles have occurred without a malfunction.
- The DTC can be cleared by using a scan tool.

DIAGNOSTIC AIDS
Inspect for the following conditions:

IMPORTANT: Remove any debris from the connector surfaces before servicing a component. Inspect the connector gaskets when diagnosing
or replacing a component. Ensure that the gaskets are installed correctly. The gaskets prevent contaminate intrusion.

- Poor terminal connection-Inspect the harness connectors for backed out terminals, improper mating, broken locks, improperly formed or
damaged terminals, and faulty terminal to wire connection. Use a corresponding mating terminal to test for proper tension. Refer to
Diagrams.
- Damaged harness-Inspect the wiring harness for damage. If the harness inspection does not reveal a problem, observe the display on the scan
tool while moving connectors and wiring harnesses related to the sensor. A change in the scan tool display may indicate the location of the
fault. Refer to Diagrams.
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 478
Chevrolet Venture V6-3.4L VIN E 2158
- PCM and engine grounds for clean and secure connections

If the DTC is determined to be intermittent, reviewing the Failure Records can be useful in determining when the DTC was last set.

P1122

Diagnostic Chart
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 479
Chevrolet Venture V6-3.4L VIN E 2159

Schematic

CIRCUIT DESCRIPTION
The Throttle Position (TP) sensor circuit provides a voltage signal that changes relative to throttle blade angle. The signal voltage will vary from
below 1.0 volt at closed throttle to above 4.0 volts at Wide Open Throttle (WOT). If the PCM detects a TP signal voltage that is intermittently
less than the range of the TP sensor, DTC P1122 will be set.

CONDITIONS FOR RUNNING THE DTC


The ignition is ON.

CONDITIONS FOR SETTING THE DTC


TP sensor intermittently indicates a throttle position signal less than 0.16 volt.

ACTION TAKEN WHEN THE DTC SETS


- The PCM will not illuminate the Malfunction Indicator Lamp (MIL).
- The PCM will store conditions which were present when the DTC set as Failure Records data only. This information will not be stored as
Freeze Frame data.

CONDITIONS FOR CLEARING THE MIL/DTC


- A History DTC will clear after 40 consecutive warm-up cycles have occurred without a malfunction.
- The DTC can be cleared by using a scan tool.

DIAGNOSTIC AIDS
Inspect for the following conditions:

IMPORTANT: Remove any debris from the connector surfaces before servicing a component. Inspect the connector gaskets when diagnosing
or replacing a component. Ensure that the gaskets are installed correctly. The gaskets prevent contaminate intrusion.

- Poor terminal connection-Inspect the harness connectors for backed out terminals, improper mating, broken locks, improperly formed or
damaged terminals, and faulty terminal to wire connection. Use a corresponding mating terminal to test for proper tension. Refer to
Diagrams.
- Damaged harness-Inspect the wiring harness for damage. If the harness inspection does not reveal a problem, observe the display on the scan
tool while moving connectors and wiring harnesses related to the sensor. A change in the scan tool display may indicate the location of the
fault. Refer to Diagrams.
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 480
Chevrolet Venture V6-3.4L VIN E 2160
- PCM and engine grounds for clean and secure connections

If the DTC is determined to be intermittent, reviewing the Failure Records can be useful in determining when the DTC was last set.

P1133

Diagnostic Chart (Part 1 Of 2)


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 481
Chevrolet Venture V6-3.4L VIN E 2161

Diagnostic Chart (Part 2 Of 2)


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 482
Chevrolet Venture V6-3.4L VIN E 2162

Schematic

CIRCUIT DESCRIPTION
The PCM monitors the Heated Oxygen Sensor (HO2S) activity for 100 seconds. During this test period the PCM counts the number of times
that the HO2S signal voltage crosses the rich to lean and lean to rich thresholds. If the PCM determines that the HO2S did not switch enough
times, DTC P1133 will be set.

A lean to rich switch is determined when the HO2S voltage changes from less than 300 mV to more than 600 mV. A rich to lean switch is
determined when the HO2S voltage changes from more than 600 mV to less than 300 mV.

CONDITIONS FOR RUNNING THE DTC


- Active MAF, TP, IAT, MAP, ECT sensor, injector circuit, EVAP, AIR or HO2S heater DTCs are not present.
- The system voltage is between 9.0 and 18.0 volts.
- Above conditions present for a 100 second monitoring period after closed loop.
- The Air pump is commanded OFF.
- Mass air flow is between 10 and 30 g/s.
- ECT is more than 50°C (122°F).
- Engine speed is between 1000 and 3000 RPM.
- The vehicle is not in Park or Neutral.

CONDITIONS FOR SETTING THE DTC


- The PCM monitors fewer than 65 rich to lean and 50 lean to rich switches for HO2S 1.
- The condition is present for a 100 second monitoring period.

ACTION TAKEN WHEN THE DTC SETS


- The PCM will illuminate the Malfunction Indicator Lamp (MIL) during the second consecutive trip in which the diagnostic test has been run
and failed.
- The PCM will store conditions which were present when the DTC set as Freeze Frame and Failure Records data.
- If the misfire is determined to be catalyst damaging, the PCM will flash the MIL.

CONDITIONS FOR CLEARING THE MIL/DTC


- The PCM will turn OFF the MIL during the third consecutive trip in which the diagnostic has been run and passed.
- The History DTC will clear after 40 consecutive warm-up cycles have occurred without a malfunction.
- The DTC can be cleared by using a scan tool.

DIAGNOSTIC AIDS
A malfunction in the HO2S heater ignition feed or ground circuit may cause a DTC P1133 to set. Inspect the HO2S heater circuitry for
intermittent faults or poor connections. Refer to Testing for Intermittent and Poor Connections in Diagrams. If connections and wiring are OK
and DTC P1133 continues to set, replace the HO2S 1.

Inspect for the following conditions:

IMPORTANT: Remove any debris from the connector surfaces before servicing a component. Inspect the connector gaskets when diagnosing
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 483
Chevrolet Venture V6-3.4L VIN E 2163
or replacing a component. Ensure that the gaskets are installed correctly. The gaskets prevent contaminate intrusion.

- Poor terminal connection-Inspect the harness connectors for backed out terminals, improper mating, broken locks, improperly formed or
damaged terminals, and faulty terminal to wire connection Use a corresponding mating terminal to test for proper tension. Refer to Diagrams.
- Damaged harness-Inspect the wiring harness for damage. If the harness inspection does not reveal a problem, observe the display on the scan
tool while moving connectors and wiring harnesses related to the sensor. A change in the scan tool display may indicate the location of the
fault. Refer to Diagrams.
- PCM and engine grounds for clean and secure connections

If the DTC is determined to be intermittent, reviewing the Failure Records can be useful in determining when the DTC was last set.

TEST DESCRIPTION
The numbers below refer to the step numbers on the diagnostic table:
2. When the system is operating correctly the HO2S voltage should toggle above and below the specified values.
5. If the low circuit is shorted to ground the HO2S voltage will be less than 400 mV when the signal circuit is jumped to ground.
6. The specified value is what is measured on a correctly operating system.
7. The specified value is what is measured on a correctly operating system.
14. This vehicle is equipped with a PCM which utilizes an Electrically Erasable Programmable Read Only Memory (EEPROM). When the PCM
is replaced, the new PCM must be programmed.

P1134

Diagnostic Chart (Part 1 Of 2)


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 484
Chevrolet Venture V6-3.4L VIN E 2164

Diagnostic Chart (Part 2 Of 2)


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 485
Chevrolet Venture V6-3.4L VIN E 2165

Schematic

CIRCUIT DESCRIPTION
The PCM continuously monitors the Heated Oxygen Sensor (HO2S) activity for 100 seconds. During the monitor period the PCM counts the
number of times that the HO2S responds from rich to lean and from lean to rich and adds the amount of time used to complete all transitions.
With this information, an average time for all transitions can be determined. The PCM then divides the rich to lean average by the lean to rich
average to obtain a ratio. If the HO2S transition time ratio is not within range, DTC P1134 will be set, indicating that the oxygen sensor is not
responding as expected to changes in exhaust oxygen content

CONDITIONS FOR RUNNING THE DTC


- Active MAF, TP, IAT, MAP, ECT sensor, injector circuit, EVAP, or HO2S heater DTCs are not present.
- Mass air flow is between 10 and 30 g/s.
- ECT is more than 50°C (122°F).
- The system voltage is between 9.0 and 18.0 volts.
- Engine speed is between 1000 and 3000 RPM
- The AIR pump is commanded OFF.
- Above conditions present for a 100 second monitoring period after closed loop.

CONDITIONS FOR SETTING THE DTC


- HO2S 1 transmission time ratio is less than 0.3 or more than 3.
- The conditions present for a 100 second monitoring period.

ACTION TAKEN WHEN THE DTC SETS


- The PCM will illuminate the Malfunction Indicator Lamp (MIL) during the second consecutive trip in which the diagnostic test has been run
and failed. The PCM will store conditions which were present when the DTC set as Freeze Frame and Failure Records data
- If the misfire is determined to be catalyst damaging the PCM will flash the MIL.

CONDITIONS FOR CLEARING THE MIL/DTC


- The PCM will turn OFF the MIL during the third consecutive trip in which the diagnostic has been run and passed.
- The History DTC will clear after 40 consecutive warm-up cycles have occurred without a malfunction.
- The DTC can be cleared by using a scan tool.

DIAGNOSTIC AIDS
Inspect for the following conditions:

IMPORTANT: Remove any debris from the connector surfaces before servicing a component. Inspect the connector gaskets when diagnosing
or replacing a component. Ensure that the gaskets are installed correctly. The gaskets prevent contaminate intrusion.

- Poor terminal connection-Inspect the harness connectors for backed out terminals, improper mating, broken locks, improperly formed or
damaged terminals, and faulty terminal to wire connection. Use a corresponding mating terminal to test for proper tension. Refer to
Diagrams.
- Damaged harness-Inspect the wiring harness for damage. If the harness inspection does not reveal a problem, observe the display on the scan
tool while moving connectors and wiring harnesses related to the sensor. A change in the scan tool display may indicate the location of the
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 486
Chevrolet Venture V6-3.4L VIN E 2166
fault. Refer to Diagrams.
- PCM and engine grounds for clean and secure connections

If the DTC is determined to be intermittent, reviewing the Failure Records can be useful in determining when the DTC was last set.

TEST DESCRIPTION
The numbers below refer to the step numbers on the diagnostic table:
2. When the system is operating correctly the HO2S voltage should toggle above and below the specified values.
5. If the low circuit is shorted to ground the HO2S voltage will be less than 400 mV when the signal circuit is jumped to ground.
6. The specified value is what is measured on a correctly operating system.
7. The specified value is what is measured on a correctly operating system.
14. This vehicle is equipped with a PCM which utilizes an Electrically Erasable Programmable Read Only Memory (EEPROM). When the PCM
is replaced, the new PCM must be programmed.

P1336

Diagnostic Chart

Refer to Engine Controls Schematics. See: Diagrams/Electrical Diagrams

CIRCUIT DESCRIPTION
The Crankshaft Position System Variation Learning feature is used to calculate reference period errors caused by slight tolerance variations in the
crankshaft, the crankshaft balancer interrupter rings, and the crankshaft position sensor hall effect switches. The calculated error allows the PCM
to accurately compensate for reference period variations. The Crankshaft Position System Variation Learning feature enhances the ability of the
PCM to detect misfire events over a wider range of engine speed and load. The crankshaft position system variation values are stored in the PCM
non volatile memory after the Crankshaft Position System Variation Learn procedure has been performed. DTC P1336 set indicates that the
crankshaft position system variation values have not been stored in the PCM and the Crankshaft Position System Variation Learn procedure must
be performed. The learn procedure is required after the following service procedures have been performed, regardless of whether or not DTC
P1336 is set:
- An PCM replacement
- An engine replacement
- A crankshaft replacement
- A crankshaft balancer replacement
- A crankshaft position sensor replacement
- Any engine repairs which disturbs crankshaft/harmonic balancer to crankshaft position sensor relationship

CONDITIONS FOR RUNNING THE DTC


- CMP or CKP sensor DTCs are not set.
- ECT is more than 65°C (149°F).

CONDITIONS FOR SETTING THE DTC


Crankshaft position system variation values are not stored in the PCM memory.

ACTION TAKEN WHEN THE DTC SETS


- The PCM will illuminate the Malfunction Indicator Lamp (MIL) during the first trip in which the diagnostic test has been run and failed.
- The PCM will store conditions which were present when the DTC set as Freeze Frame and Failure Records data.

CONDITIONS FOR CLEARING THE MIL/DTC


- The PCM will turn OFF the MIL during the third consecutive trip in which the diagnostic has been run and passed.
- The History DTC will clear after 40 consecutive warm-up cycles have occurred without a malfunction.
- The DTC can be cleared by using a scan tool.

DIAGNOSTIC AIDS
The crankshaft position system variation compensating values are stored in the PCM non volatile memory after a learn procedure has been
performed. If the actual crankshaft position variation is not within the crankshaft position system variation compensating values stored in the
PCM, DTC P0300 may set. Refer to Diagnostic Aids for DTC P0300. See: Diagnostic Trouble Code Tests and Associated Procedures/P Code
Charts/P0300
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 487
Chevrolet Venture V6-3.4L VIN E 2167

The Crankshaft Position System Variation Learn procedure must be performed when replacing the PCM to clear DTC P1336.The Crankshaft
Position System Variation Learn procedure is also required when the following service procedures have been performed, regardless of whether
or not DTC P1336 is set:
- An engine replacement
- A crankshaft replacement
- A crankshaft balancer replacement.
- A crankshaft position sensor replacement
- Any engine repairs which disturbs crankshaft/harmonic balancer to crankshaft position sensor relationship

If the crankshaft position system variation learn procedure cannot be performed successfully, inspect for the following conditions and correct as
necessary:
- ECT below 70°C (158°F)-Allow the engine to warm to above 70°C (158°F).
- Powertrain DTCs set-Refer to A Powertrain On Board Diagnostic (OBD) System Check. See: Initial Inspection and Diagnostic Overview
The scan tool crankshaft position system variation learn function will be disabled if any Powertrain DTCs other than DTC P1336 are stored
- Camshaft position signal problem detected-Refer to DTC P0341 Camshaft Position (CMP) Sensor Performance. See: Diagnostic Trouble
Code Tests and Associated Procedures/P Code Charts/P0341
- 3X reference signal problem detected-Refer to DTC P1374 Crankshaft Position (CKP) High to Low Resolution Frequency Correlation. See:
Diagnostic Trouble Code Tests and Associated Procedures/P Code Charts/P1374
- 24X reference signal problem detected-Refer to DTC P0336 Crankshaft Position (CKP) Sensor Performance. See: Diagnostic Trouble Code
Tests and Associated Procedures/P Code Charts/P0336

IMPORTANT: Remove any debris from the connector surfaces before servicing a component. Inspect the connector gaskets when diagnosing
or replacing a component. Ensure that the gaskets are installed correctly. The gaskets prevent contaminate intrusion.

- Poor terminal connection-Inspect the harness connectors for backed out terminals, improper mating, broken locks, improperly formed or
damaged terminals, and faulty terminal to wire connection. Use a corresponding mating terminal to test for proper tension. Refer to
Diagrams.
- Damaged harness-Inspect the wiring harness for damage. If the harness inspection does not reveal a problem, observe the display on the scan
tool while moving connectors and wiring harnesses related to the sensor. A change in the scan tool display may indicate the location of the
fault. Refer to Diagrams.
- PCM and engine grounds for clean and secure connections

If the DTC is determined to be intermittent, reviewing the Failure Records can be useful in determining when the DTC was last set.

P1351
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 488
Chevrolet Venture V6-3.4L VIN E 2168

Diagnostic Chart

Refer to Engine Controls Schematics. See: Diagrams/Electrical Diagrams

CIRCUIT DESCRIPTION
The Ignition Control (IC) Module sends signals that the PCM requires for fuel control and spark advance calculations. At the start of engine
crank, the IC Module controls spark advance. When the second 3X reference pulse is recognized by the PCM, the PCM applies 5.0 volts to the
Bypass circuit, commanding the IC Module to switch spark advance to PCM control. If the PCM detects an open in the IC circuit, DTC P1351
will set. The engine will start and may run with IC Module controlling spark timing.

CONDITIONS FOR RUNNING THE DTC


The engine is running.

CONDITIONS FOR SETTING THE DTC


- The PCM detects an open in the IC circuit.
- The condition is present for 300 3X reference periods (100 crankshaft revolutions).

ACTION TAKEN WHEN THE DTC SETS


- The PCM will illuminate the malfunction indicator lamp (MIL) during the second consecutive trip in which the diagnostic test has been run
and failed.
- The PCM will store conditions which were present when the DTC set as Freeze Frame and Failure Records data.
- If the misfire is determined to be catalyst damaging, the PCM will flash the MIL.

CONDITIONS FOR CLEARING THE MIL/DTC


- The PCM will turn OFF the MIL during the third consecutive trip in which the diagnostic has been run and passed.
- The History DTC will clear after 40 consecutive warm-up cycles have occurred without a malfunction.
- The DTC can be cleared by using a scan tool.

DIAGNOSTIC AIDS
Inspect for the following conditions:
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 489
Chevrolet Venture V6-3.4L VIN E 2169

IMPORTANT: Remove any debris from the connector surfaces before servicing a component. Inspect the connector gaskets when diagnosing
or replacing a component. Ensure that the gaskets are installed correctly. The gaskets prevent contaminate intrusion.

- Poor terminal connection-Inspect the harness connectors for backed out terminals, improper mating, broken locks, improperly formed or
damaged terminals, and faulty terminal to wire connection. Use a corresponding mating terminal to test for proper tension. Refer to
Diagrams.
- Damaged harness-Inspect the wiring harness for damage. If the harness inspection does not reveal a problem, observe the display on the scan
tool while moving connectors and wiring harnesses related to the sensor. A change in the scan tool display may indicate the location of the
fault. Refer to Diagrams.
- PCM and engine grounds for clean and secure connections

If the DTC is determined to be intermittent, reviewing the Failure Records can be useful in determining when the DTC was last set.

P1352

Diagnostic Chart

Refer to Engine Controls Schematics. See: Diagrams/Electrical Diagrams

CIRCUIT DESCRIPTION
The Ignition Control (IC) module sends signals that the PCM requires for fuel control and spark advance calculations. At the start of engine
crank, the IC module controls spark advance (Bypass mode.) When the second 3X reference pulse is recognized by the PCM, the PCM applies
5.0 volts to the Bypass circuit, commanding the IC module to switch spark advance to PCM control (IC mode). If the PCM detects an open in the
Bypass circuit, DTC P1352 will set. The engine will start and may run in Bypass mode timing.

CONDITIONS FOR RUNNING THE DTC


The engine is running.
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 490
Chevrolet Venture V6-3.4L VIN E 2170

CONDITIONS FOR SETTING THE DTC


- The PCM detects an open circuit in the Bypass circuit.
- The condition is present for 300 3X reference periods which equals 100 crankshaft revolutions.

ACTION TAKEN WHEN THE DTC SETS


- The PCM will illuminate the Malfunction Indicator Lamp (MIL) during the second consecutive trip in which the diagnostic test has been run
and failed.
- The PCM will store conditions which were present when the DTC set as Freeze Frame and Failure Records data.
- If the misfire is determined to be catalyst damaging, the PCM will flash the MIL.

CONDITIONS FOR CLEARING THE MIL/DTC


- The PCM will turn OFF the MIL during the third consecutive trip in which the diagnostic has been run and passed.
- The History DTC will clear after 40 consecutive warm-up cycles have occurred without a malfunction.
- The DTC can be cleared by using a scan tool.

DIAGNOSTIC AIDS
Inspect for the following conditions:

IMPORTANT: Remove any debris from the connector surfaces before servicing a component. Inspect the connector gaskets when diagnosing
or replacing a component. Ensure that the gaskets are installed correctly. The gaskets prevent contaminate intrusion.

- Poor terminal connection-Inspect the harness connectors for backed out terminals, improper mating, broken locks, improperly formed or
damaged terminals, and faulty terminal to wire connection. Use a corresponding mating terminal to test for proper tension. Refer to
Diagrams.
- Damaged harness-Inspect the wiring harness for damage. If the harness inspection does not reveal a problem, observe the display on the scan
tool while moving connectors and wiring harnesses related to the sensor. A change in the scan tool display may indicate the location of the
fault. Refer to Diagrams.
- PCM and engine grounds for clean and secure connections

If the DTC is determined to be intermittent, reviewing the Failure Records can be useful in determining when the DTC was last set.

P1361

Diagnostic Chart (Part 1 Of 2)


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 491
Chevrolet Venture V6-3.4L VIN E 2171

Diagnostic Chart (Part 2 Of 2)

Refer to Engine Controls Schematics. See: Diagrams/Electrical Diagrams

CIRCUIT DESCRIPTION
The Ignition Control (IC) module sends signals that the PCM requires for fuel control and spark advance calculations. At the start of engine
crank the IC module controls spark advance. When the second 3X reference pulse is recognized by the PCM, the PCM applies 5.0 volts to the
Bypass circuit. The 5.0 volts on the Bypass circuit commands the IC module to switch spark advance to PCM control. At this time, the IC
module will remove the ground that was applied to the IC circuit. When the IC pulses are not grounded, the IC Module can use the IC pulses to
control spark advance. A short in the IC circuit or an open or short to ground in the Bypass circuit will cause the PCM to set DTC P1361. The
engine may be started but will run with the IC module controlling spark timing.

CONDITIONS FOR RUNNING THE DTC


- Engine speed more than 600 RPM.
- DTC P1351 is not set.
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 492
Chevrolet Venture V6-3.4L VIN E 2172

CONDITIONS FOR SETTING THE DTC


- The PCM does not monitor IC pulses while IC mode spark advance is commanded.
- The conditions is present for 300 3X reference periods (100 crankshaft revolutions).

ACTION TAKEN WHEN THE DTC SETS


- The PCM will illuminate the Malfunction Indicator Lamp (MIL) during the second consecutive trip in which the diagnostic test has been run
and failed.
- The PCM will store conditions which were present when the DTC set as Freeze Frame and Failure Records data.
- If the misfire is determined to be catalyst damaging, the PCM will flash the MIL.

CONDITIONS FOR CLEARING THE MIL/DTC


- The PCM will turn OFF the MIL during the third consecutive trip in which the diagnostic has been run and passed.
- The History DTC will clear after 40 consecutive warm-up cycles have occurred without a malfunction.
- The DTC can be cleared by using a scan tool.

DIAGNOSTIC AIDS
Inspect for the following conditions:

IMPORTANT: Remove any debris from the connector surfaces before servicing a component. Inspect the connector gaskets when diagnosing
or replacing a component. Ensure that the gaskets are installed correctly. The gaskets prevent contaminate intrusion.

- Poor terminal connection-Inspect the harness connectors for backed out terminals, improper mating, broken locks, improperly formed or
damaged terminals, and faulty terminal to wire connection. Use a corresponding mating terminal to test for proper tension. Refer to
Diagrams.
- Damaged harness-Inspect the wiring harness for damage. If the harness inspection does not reveal a problem, observe the display on the scan
tool while moving connectors and wiring harnesses related to the sensor. A change in the scan tool display may indicate the location of the
fault. Refer to Diagrams.
- PCM and engine grounds for clean and secure connections

If the DTC is determined to be intermittent, reviewing the Failure Records can be useful in determining when the DTC was last set.

P1362

Diagnostic Chart (Part 1 Of 2)


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 493
Chevrolet Venture V6-3.4L VIN E 2173

Diagnostic Chart (Part 2 Of 2)

Refer to Engine Controls Schematics. See: Diagrams/Electrical Diagrams

CIRCUIT DESCRIPTION
The Ignition Control (IC) Module sends signals that the PCM requires for fuel control and spark advance calculations. At the start of engine
crank, the IC Module controls spark advance. When the second 3X reference pulse is recognized by the PCM, the PCM applies 5.0 volts to the
Bypass circuit, commanding the IC Module to switch spark advance to PCM control. If the PCM detects a short to voltage in the Bypass circuit,
DTC P1362 will set. A short to ground in the IC circuit or Bypass circuit will cause both DTC P1352 and DTC P1362 to set. The engine will
start and may run with ICM controlling spark timing.

CONDITIONS FOR RUNNING THE DTC


The engine is running.

CONDITIONS FOR SETTING THE DTC


- The PCM detects a short in the Bypass circuit.
- The conditions is present for 300 3X reference periods (100 crankshaft revolutions).

ACTION TAKEN WHEN THE DTC SETS


- The PCM will illuminate the Malfunction Indicator Lamp (MIL) during the second consecutive trip in which the diagnostic test has been run
and failed.
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 494
Chevrolet Venture V6-3.4L VIN E 2174
- The PCM will store conditions which were present when the DTC set as Freeze Frame and Failure Records data.
- If the misfire is determined to be catalyst damaging, the PCM will flash the MIL.

CONDITIONS FOR CLEARING THE MIL/DTC


- The PCM will turn OFF the MIL during the third consecutive trip in which the diagnostic has been run and passed.
- The History DTC will clear after 40 consecutive warm-up cycles have occurred without a malfunction.
- The DTC can be cleared by using a scan tool.

DIAGNOSTIC AIDS
Inspect for the following conditions:

IMPORTANT: Remove any debris from the connector surfaces before servicing a component. Inspect the connector gaskets when diagnosing
or replacing a component. Ensure that the gaskets are installed correctly. The gaskets prevent contaminate intrusion.

- Poor terminal connection-Inspect the harness connectors for backed out terminals, improper mating, broken locks, improperly formed or
damaged terminals, and faulty terminal to wire connection. Use a corresponding mating terminal to test for proper tension. Refer to
Diagrams.
- Damaged harness-Inspect the wiring harness for damage. If the harness inspection does not reveal a problem, observe the display on the scan
tool while moving connectors and wiring harnesses related to the sensor. A change in the scan tool display may indicate the location of the
fault. Refer to Diagrams.
- PCM and engine grounds for clean and secure connections

If the DTC is determined to be intermittent, reviewing the Failure Records can be useful in determining when the DTC was last set.

P1374
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 495
Chevrolet Venture V6-3.4L VIN E 2175

Diagnostic Chart (Part 1 Of 2)

Diagnostic Chart (Part 2 Of 2)


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 496
Chevrolet Venture V6-3.4L VIN E 2176

Refer to Ign System, Knock Sensor schematics. See: Diagrams/Electrical Diagrams

CIRCUIT DESCRIPTION
The 3X reference signal is produced by the Ignition Control (IC) module. The IC module calculates the 3X reference signal by dividing the
Crankshaft Position (CKP) sensor 7X pulses by 2 when the engine is running and the CKP synchronizing pulses are being received. The PCM
uses the 3X reference signal to calculate the engine RPM and the crankshaft position at engine speeds above 1600 RPM. The PCM also uses
these pulses to initiate injector pulses. The PCM compares the 3X reference pulses to the 24X CKP pulses and the CMP pulses. If the PCM
receives an incorrect number of pulses on the 3X circuit a DTC P1374 will set and the PCM will use the 24X CKP reference circuit for fuel and
ignition control. The engine will continue to start and run using only the 24X CKP and Camshaft Position (CMP) sensor signals.

CONDITIONS FOR RUNNING THE DTC


The engine is running (24X reference pulses are being received).

CONDITIONS FOR SETTING THE DTC


- The ratio of 24X reference pulses to 3X reference pulses received by the PCM does not equal 8.
- The ratio of 24X reference pulses to camshaft position PCM input pulses received by the PCM equals 48.
- The conditions are present for more than 10 seconds.

ACTION TAKEN WHEN THE DTC SETS


- The PCM will illuminate the Malfunction Indicator Lamp (MIL) during the second consecutive trip in which the diagnostic test has been run
and failed.
- The PCM will store conditions which were present when the DTC set as Freeze Frame and Failure Records data.
- If the misfire is determined to be catalyst damaging, the PCM will flash the MIL.

CONDITIONS FOR CLEARING THE MIL/DTC


- The PCM will turn OFF the MIL during the third consecutive trip in which the diagnostic has been run and passed.
- The History DTC will clear after 40 consecutive warm-up cycles have occurred without a malfunction.
- The DTC can be cleared by using a scan tool.

DIAGNOSTIC AIDS
DTC P1374 can be caused by secondary components leaking high voltage into the IC Module. Inspect for the following conditions:
- Incorrect harness routing near secondary ignition components
- Ignition coil arcing to wiring harness or IC Module- Inspect the ignition coils for the following conditions:
- Cracks
- Carbon tracking
- Any other signs of damage
- Secondary ignition wires arcing to wiring harness
- The MAP sensor reading will freeze when the 3X signal is lost.
After the MAP sensor freezes, DTC P0101 Mass Air Flow (MAF) Sensor Performance may set due to the incorrect MAP value and the
engine may be hard to start (possible long crank). Eventually (after a long crank) a DTC P0108 Manifold Absolute Pressure (MAP) Sensor
Circuit High Voltage may also set and replace the MAP sensor value with a default value and the engine will start and regain some
performance.

IMPORTANT: Remove any debris from the connector surfaces before servicing a component. Inspect the connector gaskets when diagnosing
or replacing a component. Ensure that the gaskets are installed correctly. The gaskets prevent contaminate intrusion.

- Poor terminal connection-Inspect the harness connectors for backed out terminals, improper mating, broken locks, improperly formed or
damaged terminals, and faulty terminal to wire connection. Use a corresponding mating terminal to test for proper tension. Refer to
Diagrams.
- Damaged harness-Inspect the wiring harness for damage. If the harness inspection does not reveal a problem, observe the display on the scan
tool while moving connectors and wiring harnesses related to the sensor. A change in the scan tool display may indicate the location of the
fault. Refer to Diagrams.
- PCM and engine grounds for clean and secure connections

If the DTC is determined to be intermittent, reviewing the Failure Records can be useful in determining when the DTC was last set.

TEST DESCRIPTION
The numbers below refer to the step numbers on the diagnostic table:
10. This vehicle is equipped with a PCM which utilizes an Electrically Erasable Programmable Read Only Memory (EEPROM). When the PCM
is being replaced, the new PCM must be programmed.

P1380
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 497
Chevrolet Venture V6-3.4L VIN E 2177

Diagnostic Chart

Refer to Engine Controls Schematics. See: Diagrams/Electrical Diagrams

CIRCUIT DESCRIPTION
The Powertrain Control Module (PCM) receives rough road information from the Electronic Brake Control Module (EBCM) on the serial data
circuit. The PCM uses the rough road information to enhance the misfire diagnostic by distinguishing crankshaft speed variations caused by
driving on rough road surfaces from variations caused by true misfires. The EBCM transmits rough road information based on inputs from the
wheel speed sensors. If the EBCM detects a condition which does not allow the EBCM to properly identify rough road situations while a misfire
condition is being detected by the PCM, DTC P1380 is set.

CONDITIONS FOR RUNNING THE DTC


- The engine load is less than 87 percent.
- The engine speed is less than 5000 RPM.
- The vehicle speed is more than 10 mph.
- A misfire DTC is occurring and requesting that the Malfunction Indicator Lamp (MIL) be illuminated.

CONDITIONS FOR SETTING THE DTC


The PCM has detected a EBCM rough road sensing error.

ACTION TAKEN WHEN THE DTC SETS


- The PCM will not illuminate the malfunction indicator lamp (MIL).
- The PCM will store conditions which were present when the DTC set as Failure Records data only. This information will not be stored as
Freeze Frame data.

CONDITIONS FOR CLEARING THE MIL/DTC


- A History DTC will clear after 40 consecutive warm-up cycles have occurred without a malfunction.
- The DTC can be cleared by using a scan tool.

P1381

Diagnostic Chart

Refer to Engine control schematics. See: Diagrams/Electrical Diagrams

CIRCUIT DESCRIPTION
The Powertrain Control Module (PCM) receives rough road information from the Electronic Brake Control Module (EBCM) on the Class II
serial data circuit. The PCM uses the rough road information to enhance the misfire diagnostic by distinguishing crankshaft speed variations
caused by driving on rough road surfaces from variations caused by true misfires. The EBCM transmits rough road information based on inputs
from the wheel speed sensors. If a loss of communication occurs which causes the PCM to not receive rough road information while DTC P0300
is requesting the malfunction indicator lamp (MIL) DTC P1381 is set.

CONDITIONS FOR RUNNING THE DTC


- The engine load is less than 87 percent.
- The engine speed is less than 5000 RPM.
- The vehicle speed is greater than 10 mph.
- A misfire DTC is occurring and requesting that the MIL be illuminated.
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 498
Chevrolet Venture V6-3.4L VIN E 2178

CONDITIONS FOR SETTING THE DTC


The PCM detects a loss of communication with the EBCM for at least 5 seconds.

ACTION TAKEN WHEN THE DTC SETS


- The PCM will riot illuminate the Malfunction Indicator Lamp (MIL).
- The PCM will store conditions which were present when the DTC set as Failure Records data only. This information will riot be stored as
Freeze Frame data.

CONDITIONS FOR CLEARING THE MIL/DTC


- A History DTC will clear after 40 consecutive warm-up cycles have occurred without a malfunction
- The DTC car be cleared by using a scan tool.

DIAGNOSTIC AIDS
Inspect for the following conditions:

IMPORTANT: Remove any debris from the connector surfaces before servicing a component. inspect the connector gaskets when diagnosing
or replacing a component. Ensure that the gaskets are installed correctly. The gaskets prevent contaminate intrusion.

- Poor terminal connection-Inspect the harness connectors for backed out terminals, improper mating, broken locks, improperly formed or
damaged terminals, and faulty terminal to wire connection. Use a corresponding mating terminal to test for proper tension. Refer to
Diagrams.
- Damaged harness-Inspect the wiring harness for damage. If the harness inspection does not reveal a problem, observe the display on the scan
tool while moving connectors and wiring harnesses related to the sensor. A change in the scan tool display may indicate the location of the
fault. Refer to Diagrams.
- PCM and engine grounds for clean and secure connections

If the DTC is determined to be intermittent, reviewing the Failure Records can be useful in determining when the DTC was last set.

TEST DESCRIPTION
Numbers below refer to the step numbers on the Diagnostic Table:
2. Ensures that the EBCM/EBTCM is capable of transmitting serial data on the serial data circuit.

P1404

Diagnostic Chart (Part 1 Of 2)


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 499
Chevrolet Venture V6-3.4L VIN E 2179

Diagnostic Chart(Part 2 Of 2)
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 500
Chevrolet Venture V6-3.4L VIN E 2180

Schematic

CIRCUIT DESCRIPTION
The PCM monitors the EGR valve pintle position input to ensure that the valve responds properly to commands from the PCM. When the
ignition is turned on, the PCM learns the EGR closed valve pintle position. The PCM compares the learned EGR closed valve pintle position to
the Actual EGR position when the EGR valve is commanded closed. If the Actual EGR position indicates that the EGR valve is still open when
the PCM is commanding the EGR valve closed, DTC P1404 will set.

CONDITIONS FOR RUNNING THE DTC


- IAT is more than -10°C (14°F).
- Engine run time is achieved. The length of time ranges from 20 seconds to 6 minutes depending upon engine coolant temperature at start-up.
- System voltage is between 10.0 volts and 18.0 volts.
- Desired EGR must equal zero.

CONDITIONS FOR SETTING THE DTC


- EGR Feedback is 0.2 volt more than the EGR Closed Valve Pintle Position when the Desired EGR Position is commanded to 0 percent.
- The above condition is present for longer than 20 seconds.

ACTION TAKEN WHEN THE DTC SETS


- The PCM will illuminate the Malfunction Indicator Lamp (MIL) during the first trip in which the diagnostic test has been run and failed.
- The PCM will store conditions which were present when the DTC set as Freeze Frame and Failure Records data.

CONDITIONS FOR CLEARING THE MIL/DTC


- The PCM will turn OFF the MIL during the third consecutive trip in which the diagnostic has been run and passed.
- The History DTC will clear after 40 consecutive warm-up cycles have occurred without a malfunction.
- The DTC can be cleared by using a scan tool.

DIAGNOSTIC AIDS
Inspect for the following:
- Inspect for excessive deposits on the EGR valve pintle or seat.
- Remove the EGR valve and inspect for deposits that may interfere with the EGR valve pintle extending completely or cause the pintle to
stick.

IMPORTANT: Remove any debris from the connector surfaces before servicing a component. Inspect the connector gaskets when diagnosing
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 501
Chevrolet Venture V6-3.4L VIN E 2181
or replacing a component. Ensure that the gaskets are installed correctly. The gaskets prevent contaminate intrusion.

- Poor terminal connection-Inspect the harness connectors for backed out terminals, improper mating, broken locks, improperly formed or
damaged terminals, and faulty terminal to wire connection. Use a corresponding mating terminal to test for proper tension. Refer to
Diagrams.
- Damaged harness-Inspect the wiring harness for damage. If the harness inspection does not reveal a problem, observe the display on the scan
tool while moving connectors and wiring harnesses related to the sensor. A change in the scan tool display may indicate the location of the
fault. Refer to Diagrams.
- PCM and engine grounds for clean and secure connections

If the DTC is determined to be intermittent, reviewing the Failure Records can be useful in determining when the DTC was last set.

TEST DESCRIPTION
Numbers below refer to the step numbers on the Diagnostic Table:
2. Verifies that the malfunction is present.
4. If DTC P1404 will only set under certain conditions, the malfunction may be intermittent; refer to DTC P1404 Diagnostic Aids. If an
intermittent wiring problem is not present, Inspect for a poor connection at the PCM or the EGR valve. If the connections are OK and DTC
P1404 continues to set, replace the EGR valve.
14. This vehicle is equipped with a PCM which utilizes an Electrically Erasable Programmable Read Only Memory (EEPROM). When the PCM
is being replaced, the new PCM must be programmed.

P1441
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 502
Chevrolet Venture V6-3.4L VIN E 2182

Diagnostic Chart

Refer to Emission Hose Routing Diagram, EVAP SYSTEM OVERVIEW. See: Emission Control Systems

SYSTEM DESCRIPTION
The Powertrain Control Module (PCM) supplies a ground to energize the EVAP purge valve (purge on). The EVAP purge valve control is Pulse
Width Modulated (PWM) or turned on and off several times a second. The duty cycle (pulse width) is determined by engine operating
conditions including load, throttle position, coolant temperature and ambient temperature. The duty cycle is calculated by the PCM and the
output is commanded when the appropriate conditions have been met. The system checks for conditions that cause the EVAP system to purge
continuously by commanding the EVAP vent valve ON (Closed) and the EVAP canister purge valve OFF (Closed). If vacuum level in the fuel
tank increases during the test, a continuous purge flow condition is indicated and DTC P1441 will set.

CONDITIONS FOR RUNNING THE DTC


All conditions for DTC P0440, P0442 and P0446 diagnostic tests have been met and passed.

CONDITIONS FOR SETTING THE DTC


A continuous open purge flow condition is detected during the diagnostic test (fuel tank pressure decreases to less than -11 in. H20.

ACTION TAKEN WHEN THE DTC SETS


- The PCM will illuminate the Malfunction Indicator Lamp (MIL) during the second consecutive trip in which the diagnostic test has been run
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 503
Chevrolet Venture V6-3.4L VIN E 2183
and failed.
- The PCM will store conditions which were present when the DTC set as Freeze Frame and Failure Records data.
- If the misfire is determined to be catalyst damaging, the PCM will flash the MIL.

CONDITIONS FOR CLEARING THE MIL/DTC


- The PCM will turn the MIL OFF during the first trip in which the diagnostic has been run and passed.
- The history DTC will clear when the PCM turns OFF the MIL.
- The DTC can be cleared by using a scan tool.

DIAGNOSTIC AIDS
The following conditions will set a DTC P1441.
- EVAP canister purge valve leaking internally.
- EVAP purge and engine vacuum lines switched at the EVAP canister purge valve.
- EVAP canister purge valve control circuit grounded.

Inspect for the following conditions:


- Incorrect vacuum line routing.
Verify that the source vacuum line routing to the EVAP purge valve is correct and that the EVAP purge and source vacuum lines to the
EVAP canister purge valve are not switched.
- Malfunctioning or damaged canister.
- Inspect for carbon release in the EVAP system.

If the harness appears to be OK, connect the J 41413 EVAP Pressure/Purge Diagnostic Station to the EVAP service port, pressurize the EVAP
system to 10 in. H20 and observe the Fuel Tank Pressure parameter on the scan tool while moving connectors and wiring harnesses related to the
EVAP purge valve. A sudden change in the display will indicate the location of the malfunction.

IMPORTANT: Remove any debris from the connector surfaces before servicing a component. Inspect the connector gaskets when diagnosing
or replacing a component. Ensure that the gaskets are installed correctly. The gaskets prevent contaminate intrusion.

- Poor terminal connection-Inspect the harness connectors for backed out terminals, improper mating, broken locks, improperly formed or
damaged terminals, and faulty terminal to wire connection. Use a corresponding mating terminal to test for proper tension. Refer to
Diagrams.
- Damaged harness-Inspect the wiring harness for damage. If the harness inspection does not reveal a problem, observe the display on the scan
tool while moving connectors and wiring harnesses related to the sensor. A change in the scan tool display may indicate the location of the
fault. Refer to Diagrams.
- PCM and engine grounds for clean and secure connections

If the DTC is determined to be intermittent, reviewing the Failure Records can be useful in determining when the DTC was last set.

TEST DESCRIPTION
Numbers below refer to the step numbers on the Diagnostic Table:
1. The Powertrain On Board Diagnostic (OBD) System Check prompts you to complete some of the basic test and store the Freeze Frame and
Failure Records data on the scan tool if applicable.

P1483
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 504
Chevrolet Venture V6-3.4L VIN E 2184

Diagnostic Chart

CIRCUIT DESCRIPTION
The PCM will richen the air/fuel ratio when a high coolant temperature is monitored. Called Hot Fuel Enrichment (HFE) this condition can
cause exhaust emissions to exceed the federal emissions standards for this vehicle. This DTC is required in order to prevent HFE from being
active during a skewed ECT sensor condition or during an actual cooling system condition that results in hot engine coolant. The PCM will
calculate an engine coolant temperature value based on IAT, engine speed, vehicle speed and engine load. If the ECT sensor value is higher than
the calculated coolant temperature during the Conditions for Running the DTC, this DTC sets and HFE is disabled.

CONDITIONS FOR RUNNING THE DTC


- DTCs P0101, P0102, P0103, P0107, P0108, P0117, P0118, P0125, P0502, or P1108 are not set.
- Engine coolant temperature is the same or less than 110°C (230°F) at start-up.
OR
- The engine coolant temperature is less than 104°C (219°F) anytime at start-up.
- Intake Air Temperature, Engine Load, Engine Speed and Vehicle Speed are all within a specific range.

CONDITIONS FOR SETTING THE DTC


The PCM determines the monitored engine coolant temperature (from the ECT sensor) is more than the calculated coolant temperature.

ACTION TAKEN WHEN THE DTC SETS


- The PCM will not illuminate the Malfunction Indicator Lamp (MIL).
- The PCM will store conditions which were present when the DTC set as Failure Records data only. This information will not be stored as
Freeze Frame data.

CONDITIONS FOR CLEARING THE MIL/DTC


- A History DTC will clear after 40 consecutive warm-up cycles have occurred without a malfunction.
- The DTC can be cleared by using a scan tool.

DIAGNOSTIC AIDS
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 505
Chevrolet Venture V6-3.4L VIN E 2185
- The most likely cause of this DTC is a cooling system problem. Perform the Electric Cooling Fan Diagnosis and also visually inspect the
cooling system for problems such as restricted radiator AIR flow. Refer to Engine Cooling for more cooling system diagnostic aids. See:
Engine, Cooling and Exhaust/Cooling System
- The IAT sensor must indicate the actual ambient temperature to within 1 degree. If the IAT sensor is accurate the ECT sensor must be
inaccurate. Test of the ECT sensor can be made by comparing actual coolant temperature to the ECT scan tool display.
Obtain actual coolant temperature using a thermometer located in the engine coolant. A test of the ECT sensors resistance may also be
performed.
If the actual coolant temperature is the same as the ECT scan tool display then the engine was not allowed to cool completely. Allow the
vehicle to cool and repeat the diagnostic table.

TEST DESCRIPTION
The numbers below refer to the step numbers on the diagnostic table:
3. Compares temperature readings of the ECT and IAT sensors.
4. Tests the temperature of the ECT sensor.

P1546

Diagnostic Chart
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 506
Chevrolet Venture V6-3.4L VIN E 2186

CIRCUIT DESCRIPTION
Refer to Engine Controls Schematics inder Powertrain Management. See: Diagrams

Output Driver Modules (ODMs) are used by the Powertrain Control Module (PCM) to turn on many of the current-driven devices that are
needed to control various engine and transaxle functions. Each ODM is capable of controlling up to 7 separate outputs by applying ground to the
device which the PCM is commanding ON. ODMs have the capability of diagnosing each output circuit individually. DTC P1546 set indicates
an improper voltage level has been detected on the output circuit which controls the A/C compressor control relay.

CONDITIONS FOR RUNNING THE DTC


The ignition is ON.

CONDITIONS FOR SETTING THE DTC


^ An improper voltage level has been detected on the output circuit which controls the A/C compressor control relay.
^ The above condition is present for at least 30 seconds.

ACTION TAKEN WHEN THE DTC SETS


^ The PCM will not illuminate the Malfunction Indicator Lamp (MIL).
^ The PCM will store conditions which were present when the DTC set as Failure Records data only. This information will not be stored as
Freeze Frame data.

CONDITIONS FOR CLEARING THE MIL/DTC


^ A History DTC will clear after 40 consecutive warm-up cycles have occurred without a malfunction.
^ The DTC can be cleared by using a scan tool.

DIAGNOSTIC AIDS
Inspect for the following conditions:

IMPORTANT: Remove any debris from the connector surfaces before servicing a component. Inspect the connector gaskets when diagnosing
or replacing a component. Ensure that the gaskets are installed correctly. The gaskets prevent contaminate intrusion.

^ Poor terminal connection-Inspect the harness connectors for backed out terminals, improper mating, broken locks, improperly formed or
damaged terminals, and faulty terminal to wire connection. Use a corresponding mating terminal to test for proper tension. Refer to
Diagrams.
^ Damaged harness-Inspect the wiring harness for damage. If the harness inspection does not reveal a problem, observe the display on the scan
tool while moving connectors and wiring harnesses related to the sensor. A change in the scan tool display may indicate the location of the
fault. Refer to Diagrams.
^ PCM and engine grounds for clean and secure connections

If the DTC is determined to be intermittent, reviewing the Failure Records can be useful in determining when the DTC was last set.

TEST DESCRIPTION
The numbers below refer to the step numbers on the diagnostic table:
2. Listen for a click when the relay operates. Command both the ON and OFF states. Repeat the commands as necessary.
3. This step tests for voltage at the coil feed side of the relay.
4. This step verifies that the PCM is providing ground to the relay.
5. This step tests if ground is constantly being applied to the relay.
12. The PCM utilizes Electrically Erasable Programmable Read Only Memory (EEPROM). When the PCM is replaced, the new PCM must be
programmed.

P1554
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 507
Chevrolet Venture V6-3.4L VIN E 2187

Diagnostic Chart
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 508
Chevrolet Venture V6-3.4L VIN E 2188

Schematic

CIRCUIT DESCRIPTION
The Cruise Control Module sends the cruise status input to the PCM to indicate when cruise control is engaged. The PCM monitors the cruise
status signal while commanding cruise to be disengaged by grounding the cruise inhibit circuit. Any of the following conditions may cause the
PCM to inhibit cruise control operation:
- Engine is not running long enough for cruise control operation.
- Transaxle range inputs indicate park, neutral, low, or reverse gear is selected.
- Engine speed is too high or too low.
- Vehicle speed is too high or too low.
- TCS is active for longer than 2 seconds.
- Vehicle acceleration or deceleration rate is too high.

CONDITIONS FOR RUNNING THE DTC


The PCM is commanding the cruise control module to not allow cruise control operation (cruise Inhibit circuit grounded).

CONDITIONS FOR SETTING THE DTC


- The Cruise Status input to the PCM indicates that cruise control is still active.
- The conditions is present for longer than 1 second.

ACTION TAKEN WHEN THE DTC SETS


- The PCM will not illuminate the Malfunction Indicator Lamp (MIL).
- The PCM will store conditions which were present when the DTC set as Failure Records data only. This information will not be stored as
Freeze Frame data.

CONDITIONS FOR CLEARING THE MIL/DTC


- A History DTC will clear after 40 consecutive warm-up cycles have occurred without a malfunction.
- The DTC can be cleared by using a scan tool.

DIAGNOSTIC AIDS
Inspect for the following conditions:

IMPORTANT: Remove any debris from the connector surfaces before servicing a component. Inspect the connector gaskets when diagnosing
or replacing a component. Ensure that the gaskets are installed correctly. The gaskets prevent contaminate intrusion.

- Poor terminal connection-Inspect the harness connectors for backed out terminals, improper mating, broken locks, improperly formed or
damaged terminals, and faulty terminal to wire connection. Use a corresponding mating terminal to test for proper tension. Refer to
Diagrams.
- Damaged harness-Inspect the wiring harness for damage. If the harness inspection does not reveal a problem, observe the display on the scan
tool while moving connectors and wiring harnesses related to the sensor A change in the scan tool display may indicate the location of the
fault. Refer to Diagrams.
- PCM and engine grounds for clean and secure connections
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 509
Chevrolet Venture V6-3.4L VIN E 2189

If the DTC is determined to be intermittent, reviewing the Failure Records can be useful in determining when the DTC was last set.

TEST DESCRIPTION
The numbers below refer to the step numbers on the diagnostic table:
7. This vehicle is equipped with a PCM which utilizes an Electrically Erasable Programmable Read Only Memory (EEPROM). When the PCM
is being replaced, the new PCM must be programmed

P1571

Diagnostic Chart
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 510
Chevrolet Venture V6-3.4L VIN E 2190

Schematic

CIRCUIT DESCRIPTION
The Traction Control System (TCS) uses the antilock brake system in conjunction with the Powertrain Control Module (PCM) fuel and ignition
controls to limit drive wheel slippage during acceleration. The PCM controlled portion of the TCS reduces engine torque by any or all of the
following methods:
- Retarding spark timing
- Altering air/fuel ratio
- Shutting off up to 3 injectors

To determine the amount of torque reduction required, the PCM monitors the TCS desired torque Pulse Width Modulated (PWM) signal from
the Electronic Brake And Traction Control Module (EBTCM). The PCM also provides a TCS delivered torque PWM informing the EBTCM
how much torque is being produced by the engine. The Desired Torque display on the scan tool indicates the amount of engine torque requested
by the EBTCM. With the traction control inactive, the desired torque should vary between 99 and 100 percent. The Desired Torque display on
the scan tool is not the PWM duty cycle.

CONDITIONS FOR SETTING THE DTC


- The desired torque signal PWM duty cycle is less than 10 percent or more than 95 percent.
- The above condition is present for at least 10 seconds.

ACTION TAKEN WHEN THE DTC SETS


- The PCM will not illuminate the Malfunction Indicator Lamp (MIL).
- The PCM will store conditions which were present when the DTC set as Failure Records data only. This information will not be stored as
Freeze Frame data.

CONDITIONS FOR CLEARING THE MIL/DTC


- A History DTC will clear after 40 consecutive warm-up cycles have occurred without a malfunction.
- The DTC can be cleared by using a scan tool.

DIAGNOSTIC AIDS
Inspect the following conditions:

IMPORTANT: Remove any debris from the connector surfaces before servicing a component. Inspect the connector gaskets when diagnosing
or replacing a component. Ensure that the gaskets are installed correctly. The gaskets prevent contaminate intrusion.

- Poor terminal connection-Inspect the harness connectors for backed out terminals, improper mating, broken locks, improperly formed or
damaged terminals, and faulty terminal to wire connection. Use a corresponding mating terminal to test for proper tension. Refer to
Diagrams.
- Damaged harness-Inspect the wiring harness for damage. If the harness inspection does not reveal a problem, observe the display on the scan
tool while moving connectors and wiring harnesses related to the sensor. A change in the scan tool display may indicate the location of the
fault. Refer to Diagrams.
- PCM and engine grounds for clean and secure connections

If the DTC is determined to be intermittent, reviewing the Failure Records can be useful in determining when the DTC was last set.

P1585
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 511
Chevrolet Venture V6-3.4L VIN E 2191

Diagnostic Chart (Part 1 Of 2)


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 512
Chevrolet Venture V6-3.4L VIN E 2192

Diagnostic Chart (Part 2 Of 2)

Refer to Engine Controls Schematics. See: Diagrams/Electrical Diagrams

CIRCUIT DESCRIPTION
Output Driver Modules (ODMs) are used by the PCM to turn on many of the current-driven devices that are needed to control various engine
and transaxle functions. Each ODM is capable of controlling up to 7 separate outputs by applying ground to the device which the PCM is
commanding ON. DTC P1585 set indicates an improper voltage level has been detected on the output circuit which controls the Cruise Control
Inhibit circuit.

CONDITIONS FOR RUNNING THE DTC


- The ignition is ON.
- The system voltage between 9.0 and 18.0 volts.

CONDITIONS FOR SETTING THE DTC


- An improper voltage level has been detected on the output circuit which controls the cruise control inhibit.
- The above condition is present for at least 30 seconds.

ACTION TAKEN WHEN THE DTC SETS


- The PCM will not illuminate the malfunction indicator lamp (MIL).
- The PCM will store conditions which were present when the DTC set as Failure Records data only. This information will not be stored as
Freeze Frame data.

CONDITIONS FOR CLEARING THE MIL/DTC


- A History DTC will clear after 40 consecutive warm-up cycles have occurred without a malfunction.
- The DTC can be cleared by using a scan tool.

DIAGNOSTIC AIDS
Inspect for the following conditions:

IMPORTANT: Remove any debris from the connector surfaces before servicing a component. Inspect the connector gaskets when diagnosing
or replacing a component. Ensure that the gaskets are installed correctly. The gaskets prevent contaminate intrusion.

- Poor terminal connection-Inspect the harness connectors for backed out terminals, improper mating, broken locks, improperly formed or
damaged terminals, and faulty terminal to wire connection. Use a corresponding mating terminal to test for proper tension. Refer to
Diagrams.
- Damaged harness-Inspect the wiring harness for damage. If the harness inspection does not reveal a problem, observe the display on the scan
tool while moving connectors and wiring harnesses related to the sensor. A change in the scan tool display may indicate the location of the
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 513
Chevrolet Venture V6-3.4L VIN E 2193
fault. Refer to Diagrams.
- PCM and engine grounds for clean and secure connections

If the DTC is determined to be intermittent, reviewing the Failure Records can be useful in determining when the DTC was last set.

TEST DESCRIPTION
Numbers below refer to the step numbers on the Diagnostic Table.
2. Normally, ignition feed voltage should be present on the control circuit with the PCM disconnected and the ignition turned ON.
3. Tests for a shorted component or a short to battery positive voltage on the control circuit. Either condition would result in a measured current
of over 500 milliamps. Also tests for a component that is going open while being operated, resulting in a measured current of 0 milliamps.
4. Tests for a short to voltage on the control circuit.
15. This vehicle is equipped with a PCM which utilizes an Electrically Erasable Programmable Read Only Memory (EEPROM). When the PCM
is being replaced, the new PCM must be programmed.

P1626

Diagnostic Chart

Refer to Power, Ground, MIL, DLC, in Data Link Communications, See: Data Link Connectorand Pass Key III in Theft Deterrent. See:
Accessories and Optional Equipment/Antitheft and Alarm Systems

CIRCUIT DESCRIPTION
The Vehicle Theft Deterrent (VTD) module produces the theft deterrent fuel enable signal when ignition is ON and the proper key resistor pellet
is detected. The Powertrain Control Module (PCM) monitors the fuel enable signal during crank. If the proper signal is present on the Class II
Serial Data Circuit, the PCM enables the fuel delivery in order to allow the engine to start. If the PCM determines that the fuel enable signal is
not present or incorrect while the engine is running, DTC P1626 is set. The engine continues to start and run as long as DTC P1626 is stored. If
the problem affects inputs to the VTD signal, the starter motor may be disabled. Refer to Vehicle Theft Deterrent (VTD) Description and Vehicle
Theft Deterrent (VTD) Operation. See: Accessories and Optional Equipment/Antitheft and Alarm Systems

CONDITIONS FOR RUNNING THE DTC


- DTC P1631 is not present.
- An attempt is made to start the engine. The theft deterrent system has allowed fuel delivery.

CONDITIONS FOR SETTING THE DTC


The PCM has detected a loss of the state of health serial data message from the theft deterrent system.

ACTION TAKEN WHEN THE DTC SETS


- The PCM will not illuminate the Malfunction Indicator Lamp (MIL).
- The PCM will store conditions which were present when the DTC set as Failure Records data only. This information will not be stored as
Freeze Frame data.

CONDITIONS FOR CLEARING THE MIL/DTC


- A History DTC will clear after 40 consecutive warm-up cycles have occurred without a malfunction.
- The DTC can be cleared by using a scan tool.

DIAGNOSTIC AIDS
Inspect for the following conditions:

IMPORTANT: Remove any debris from the connector surfaces before servicing a component. Inspect the connector gaskets when diagnosing
or replacing a component. Ensure that the gaskets are installed correctly. The gaskets prevent contaminate intrusion.
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 514
Chevrolet Venture V6-3.4L VIN E 2194

- Poor terminal connection-Inspect the harness connectors for backed out terminals, improper mating, broken locks, improperly formed or
damaged terminals, and faulty terminal to wire connection. Use a corresponding mating terminal to test for proper tension. Refer to
Diagrams.
- Damaged harness-Inspect the wiring harness for damage. If the harness inspection does not reveal a problem, observe the display on the scan
tool while moving connectors and wiring harnesses related to the sensor. A change in the scan tool display may indicate the location of the
fault. Refer to Diagrams.
- PCM and engine grounds for clean and secure connections

If the DTC is determined to be intermittent, reviewing the Failure Records can be useful in determining when the DTC was last set.

P1630

Diagnostic Chart

Refer to Power, Ground, MIL, DLC, in Data Link Communications, See: Data Link Connector and Pass Key III in Theft Deterrent. See:
Accessories and Optional Equipment/Antitheft and Alarm Systems

CIRCUIT DESCRIPTION
The Vehicle Theft Deterrent (VTD) module produces the theft deterrent fuel enable signal when ignition is ON and the proper key resistor pellet
is detected. The Powertrain Control Module (PCM) monitors the fuel enable signal during crank. If the proper signal is present on the Class II
Serial Data Circuit, the PCM enables the fuel delivery in order to allow the engine to start. If the Powertrain Control Module (PCM) is replaced,
the replacement PCM should learn the password within a few seconds after the ignition is turned ON. DTC P1630 is an information code
indicating that the PCM is ready to learn the theft deterrent password. The engine starts and continues to run with DTC P1630 set. Refer to
Vehicle Theft Deterrent (VTD) Description and Vehicle Theft Deterrent (VTD) Operation. See: Accessories and Optional Equipment/Antitheft
and Alarm Systems

CONDITIONS FOR RUNNING THE DTC


- The theft deterrent system has allowed fuel delivery.
- The PCM is in the theft deterrent password learn mode.

CONDITIONS FOR SETTING THE DTC


The PCM remains in theft deterrent password learn mode for more than 2 seconds.

ACTION TAKEN WHEN THE DTC SETS


- The PCM will not illuminate the Malfunction Indicator Lamp (MIL).
- The PCM will store conditions which were present when the DTC set as Failure Records data only. This information will not be stored as
Freeze Frame data.

CONDITIONS FOR CLEARING THE MIL/DTC


- A History DTC will clear after 40 consecutive warm-up cycles have occurred without a malfunction.
- The DTC can be cleared by using the scan tool Clear Info function.

DIAGNOSTIC AIDS
A replacement PCM is in a functional state to learn the password from the VTD System. If the Theft Deterrent Module is replaced, the PCM
must be placed in password learning mode to relearn the new password. Once learned, the password becomes permanent information that
remains with the vehicle. The loss of PCM battery or ignition voltage does not affect the programmed password information.

Refer to PCM Replacement/Programming. See: Powertrain Control Module

P1631
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 515
Chevrolet Venture V6-3.4L VIN E 2195

Diagnostic Chart

Refer to Power, Ground, MIL, DLC, in Data Link Communications, See: Data Link Connector and Key III in Theft Deterrent. See: Accessories and
Optional Equipment/Antitheft and Alarm Systems

CIRCUIT DESCRIPTION
The Vehicle Theft Deterrent (VTD) module produces the theft deterrent fuel enable signal when ignition is ON and the proper key resistor pellet
is detected. The Powertrain Control Module (PCM) monitors the fuel enable signal during crank. If the proper signal is present on the Class II
Serial Data Circuit, the PCM enables the fuel delivery in order to allow the engine to start. If the PCM detects an incorrect password (theft
deterrent system failure or attempted vehicle theft, DTC 1631 is set. The engine may not start or crank as long as the condition is present. Refer
to Vehicle Theft Deterrent (VTD) Description and Vehicle Theft Deterrent (VTD) Operation. See: Accessories and Optional
Equipment/Antitheft and Alarm Systems

CONDITIONS FOR RUNNING THE DTC


The ignition is ON.

CONDITIONS FOR SETTING THE DTC


- The PCM is detecting an incorrect password from the VTD system.
- The conditions is present for less than 1 second.

ACTION TAKEN WHEN THE DTC SETS


- The PCM will not illuminate the Malfunction Indicator Lamp (MIL).
- The PCM will store conditions which were present when the DTC set as Failure Records data only. This information will not be stored as
Freeze Frame data.

CONDITIONS FOR CLEARING THE MIL/DTC


- A History DTC will clear after 40 consecutive warm-up cycles have occurred without a malfunction.
- The DTC can be cleared by using a scan tool.

DIAGNOSTIC AIDS
DTC P1631 indicates that the vehicle theft deterrent password that the PCM has learned does not agree with the password being received from
the theft deterrent system. This condition can occur if an incorrect key is being used when attempting to start the vehicle or if the Theft Deterrent
Module has been replaced and the PCMs password learn function has not been enabled.

P1635
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 516
Chevrolet Venture V6-3.4L VIN E 2196

Diagnostic Chart
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 517
Chevrolet Venture V6-3.4L VIN E 2197

Schematic

CIRCUIT DESCRIPTION
The PCM uses the 5 Volt Reference A circuit as a sensor feed to the following sensors:
- The TP sensor.
- The MAP sensor.
- The EGR Valve Pintle Position sensor.

The PCM monitors the voltage on the 5 Volt Reference A circuit. If the voltage is out of tolerance, the PCM will set DTC P1635.

CONDITIONS FOR RUNNING THE DTC


The ignition is on.

CONDITIONS FOR SETTING THE DTC


- The PCM detects a voltage out of tolerance condition on the 5 Volt Reference A circuit.
- Above condition for longer than 10 seconds.

ACTION TAKEN WHEN THE DTC SETS


- The PCM will illuminate the Malfunction Indicator Lamp (MIL) during the second consecutive trip in which the diagnostic has been run and
failed.
- If equipped with traction control, the PCM will command the Electronic Brake And Traction Control Module (EBTCM) via the serial data
circuit to turn OFF traction control, and the EBTCM will illuminate the TRACTION OFF lamp.
- The PCM will store conditions which were present when the DTC set as Freeze Frame and Failure Records data.

CONDITIONS FOR CLEARING THE MIL/DTC


- The PCM will turn OFF the MIL during the third consecutive trip in which the diagnostic has been run and passed.
- The History DTC will clear after 40 consecutive warm-up cycles have occurred without a malfunction.
- The DTC can be cleared by using a scan tool.

DIAGNOSTIC AIDS
Inspect for the following conditions:

IMPORTANT: Remove any debris from the connector surfaces before servicing a component. Inspect the connector gaskets when diagnosing
or replacing a component. Ensure that the gaskets are installed correctly. The gaskets prevent contaminate intrusion.
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 518
Chevrolet Venture V6-3.4L VIN E 2198

- Poor terminal connection-Inspect the harness connectors for backed out terminals, improper mating, broken locks, improperly formed or
damaged terminals, and faulty terminal to wire connection. Use a corresponding mating terminal to test for proper tension. Refer to
Diagrams.
- Damaged harness-Inspect the wiring harness for damage. If the harness inspection does not reveal a problem, observe the display on the scan
tool while moving connectors and wiring harnesses related to the sensor. A change in the scan tool display may indicate the location of the
fault. Refer to Diagrams.
- PCM and engine grounds for clean and secure connections

If the DTC is determined to be intermittent, reviewing the Failure Records can be useful in determining when the DTC was last set.

TEST DESCRIPTION
The numbers below refer to the step numbers on the diagnostic table:

IMPORTANT: DTC must have failed this ignition to be properly diagnosed.

2. The 5 Volt Reference circuits have multiple PCM pins, be sure to test all components on the 5 Volt Reference A circuits only.
3. The 5 Volt Reference circuits have multiple PCM pins, be sure to test all components on the 5 Volt Reference A circuits only.
9. This vehicle is equipped with a PCM which utilizes an Electrically Erasable Programmable Read Only Memory (EEPROM). When the PCM
is being replaced, the new PCM must be programmed.

P1639

Diagnostic Chart
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 519
Chevrolet Venture V6-3.4L VIN E 2199

Schematic

CIRCUIT DESCRIPTION
The PCM uses the 5 Volt Reference B circuit as a sensor feed to the following sensors:
- The A/C Pressure sensor.
- Fuel Tank Pressure (FTP) Sensor

The PCM monitors the voltage on the 5 Volt Reference B circuit. If the voltage is out of tolerance, the PCM will set DTC P1639.

CONDITIONS FOR RUNNING THE DTC


The ignition is on.

CONDITIONS FOR SETTING THE DTC


- The PCM detects a voltage out of tolerance condition on the 5 Volt Reference B circuit.
- Above condition for longer than 10 seconds.

ACTION TAKEN WHEN THE DTC SETS


- The PCM will illuminate the Malfunction Indicator Lamp (MIL) during the second consecutive trip in which the diagnostic has been run and
failed.
- If equipped with traction control, the PCM will command the Electronic Brake And Traction Control Module (EBTCM) via the serial data
circuit to turn OFF traction control, and the EBTCM will illuminate the TRACTION OFF lamp.
- The PCM will store conditions which were present when the DTC set as Freeze Frame and Failure Records data.

CONDITIONS FOR CLEARING THE MIL/DTC


The PCM will turn OFF the MIL during the third consecutive trip in which the diagnostic has been run and passed.
- The History DTC will clear after 40 consecutive warm-up cycles have occurred without a malfunction.
- The DTC can be cleared by using a scan tool.

DIAGNOSTIC AIDS
Inspect for the following conditions:

IMPORTANT: Remove any debris from the connector surfaces before servicing a component. Inspect the connector gaskets when diagnosing
or replacing a component. Ensure that the gaskets are installed correctly. The gaskets prevent contaminate intrusion.
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 520
Chevrolet Venture V6-3.4L VIN E 2200

- Poor terminal connection-Inspect the harness connectors for backed out terminals, improper mating, broken locks, improperly formed or
damaged terminals, and faulty terminal to wire connection. Use a corresponding mating terminal to test for proper tension. Refer to
Diagrams.
- Damaged harness-Inspect the wiring harness for damage. If the harness inspection does not reveal a problem, observe the display on the scan
tool while moving connectors and wiring harnesses related to the sensor. A change in the scan tool display may indicate the location of the
fault. Refer to Diagrams.
- PCM and engine grounds for clean and secure connections

If the DTC is determined to be intermittent, reviewing the Failure Records can be useful in determining when the DTC was last set.

TEST DESCRIPTION
The numbers below refer to the step numbers on the diagnostic table:

IMPORTANT: DTC must have failed this ignition to be properly diagnosed.

2. The 5 Volt Reference circuits have multiple PCM pins, be sure to test all components on the 5 Volt Reference B circuits only.
3. The 5 Volt Reference circuits have multiple PCM pins, be sure to test all components on the 5 Volt Reference B circuits only.
9. This vehicle is equipped with a PCM which utilizes an Electrically Erasable Programmable Read Only Memory (EEPROM). When the PCM
is being replaced, the new PCM must be programmed.

P1689
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 521
Chevrolet Venture V6-3.4L VIN E 2201
Diagnostic Chart (Part 1 Of 2)

Diagnostic Chart (Part 2 Of 2)

Schematic

CIRCUIT DESCRIPTION
The Electronic Brake And Traction Control Module (EBTCM) controls the Pulse Width Modulated (PWM) signal on the desired torque circuit
while monitoring the wheel speed sensors to detect slippage. The Powertrain Control Module (PCM) monitors the PWM signal arid reduces the
engine torque as needed by retarding the ignition timing, decreasing the boost duty cycle, and increasing the air/fuel ratio, or, in severe cases,
shutting OFF up to 3 fuel injectors. The PCM sends a PWM signal to the EBTCM on the delivered torque circuit informing the EBTCM of
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 522
Chevrolet Venture V6-3.4L VIN E 2202
response made to the desired torque signal. A problem with the delivered torque circuit should cause DTC P1689 to set and the Traction Control
System (TCS) to be disabled. An ABS/TCS DTC may also be set. For further ABS/TCS DTC information, refer to Antilock Brake Systems.

CONDITIONS FOR RUNNING THE DTC


The ignition is ON.

CONDITIONS FOR SETTING THE DTC


- An improper voltage level has been detected on the output circuit for the traction control delivered torque output circuit.
- The above conditions are present for at least 30 seconds.

ACTION TAKEN WHEN THE DTC SETS


- The PCM will not illuminate the Malfunction Indicator Lamp (MIL).
- The PCM will store conditions which were present when the DTC set as Failure Records data only. This information will not be stored as
Freeze Frame data.

CONDITIONS FOR CLEARING THE MIL/DTC


- A History DTC will clear after 40 consecutive warm-up cycles have occurred without a malfunction.
- The DTC can be cleared by using a scan tool.

DIAGNOSTIC AIDS
Inspect for the following conditions:

IMPORTANT: Remove any debris from the connector surfaces before servicing a component. Inspect the connector gaskets when diagnosing
or replacing a component. Ensure that the gaskets are installed correctly. The gaskets prevent contaminate intrusion.

- Poor terminal connection-Inspect the harness connectors for backed out terminals, improper mating, broken locks, improperly formed or
damaged terminals, and fault terminal to wire connection. Use a corresponding mating terminal to test for proper tension. Refer to Diagrams.
- Damaged harness-Inspect the wiring harness for damage. If the harness inspection does not reveal a problem, observe the display on the scan
tool while moving connectors and wiring harnesses related to the sensor. A change in the scan tool display may indicate the location of the
fault. Refer to Diagrams.
- PCM and engine grounds for clean and secure connections

If the DTC is determined to be intermittent, reviewing the Failure Records can be useful in determining when the DTC was last set.

TEST DESCRIPTION
Numbers below refer to the step numbers on the Diagnostic Table:
2. Normally, ignition feed voltage should be present on the control circuit with the PCM disconnected and the ignition turned ON.
3. Tests for a shorted component or a short to battery positive voltage on the control circuit. Either condition would result in a measured current
of over 500 milliamps. Also tests for a component that is going open while being operated, resulting in a measured current of 0 milliamps.
4. Tests for a short to voltage on the control circuit.
15. This vehicle is equipped with a PCM which utilizes an Electrically Erasable Programmable Read Only Memory (EEPROM). When the PCM
is being replaced, the new PCM must be programmed.

P1810
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 523
Chevrolet Venture V6-3.4L VIN E 2203

Diagnostic Chart 1 Of 2
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 524
Chevrolet Venture V6-3.4L VIN E 2204

Diagnostic Chart 2 Of 2
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 525
Chevrolet Venture V6-3.4L VIN E 2205

Schematic

Circuit Description with 4T65-E Automatic Transaxle


The automatic Transmission Fluid Pressure (TFP) manual valve position switch consists of six pressure switches (three normally-closed and
three normally-open switches). Ignition voltage is applied to each of the switches. By grounding or opening one or more of these switches with
fluid pressure from the manual valve, the PCM can detect which gear range is selected.

If the PCM detects an invalid combination of inputs (LOW/HI/LOW or LOW/LOW/LOW), then DTC P1810 sets. If the PCM detects a gear
range other than the one indicated, then DTC P1810 sets. DTC P1810 is a type B DTC.

CONDITIONS FOR RUNNING THE DTC


^ The engine speed is greater than 500 RPM for 5 seconds and not in fuel shut off.
^ The system voltage is 9-18 volts.

CONDITIONS FOR SETTING THE DTC


DTC P1810 sets when at least one of the following conditions occurs:

Condition 1
The TFP manual valve position switch indicates an invalid switch combination for 60 seconds.

Condition 2
^ No VSS DTC P0502 or P0503.
^ The vehicle speed is less than 16 km/h (10 mph).
^ TFP manual valve position switch indicates REVERSE, D2 or D4 for 7 seconds at engine start up without indicating PARK or
NEUTRAL.

Condition 3
^ No TP sensor DTC P0121, P0122 or P0123.
^ No VSS DTC P0502 or P0503.
^ No AT ISS sensor DTC P0716 or P0717.
^ No 1-2, 3-4 SS valve DTC P0751 or P0753.
^ No 2-3 SS valve DTC P0756 or P0758.
^ The TP angle is greater than 9%.
^ The vehicle speed is more than 8 km/h (5 mph).
^ The engine torque is greater than 70 N.m (50 lb ft) and one of the following conditions occurs:
- The gear ratio indicates REVERSE, D4, D3, D2 or D1 and the TFP manual valve position switch indicates PARK or NEUTRAL for
5 seconds.
- The gear ratio indicates D4, D3, D2 or D1 and the TFP manual valve position switch indicates REVERSE for 7 seconds.
- The gear ratio indicates REVERSE and the TFP manual valve position switch indicates D4, D3, D2 or D1 for 5 seconds.

ACTION TAKEN WHEN THE DTC SETS


^ The PCM illuminates the Malfunction Indicator Lamp (MIL) during the second consecutive trip in which the conditions for setting the DTC
are met.
^ The PCM commands maximum line pressure.
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 526
Chevrolet Venture V6-3.4L VIN E 2206
^ The PCM freezes shift adapts.
^ The PCM assumes D4 for shifting.
^ The PCM records the operating conditions when the Conditions for Setting the DTC are met. The PCM stores this information as Freeze
Frame and Failure Records.
^ The PCM stores DTC P1810 in PCM history during the second consecutive trip in which the conditions for setting the DTC are met.

CONDITIONS FOR CLEARING THE MIL/DTC


^ The PCM turns OFF the MIL during the third consecutive trip in which the diagnostic test runs and passes.
^ A scan tool can clear the MIL/DTC.
^ The PCM clears the DTC from the PCM history if the vehicle completes 40 consecutive warm-up cycles without an emission-related
diagnostic fault occurring.
^ The PCM cancels the DTC default actions when the fault no longer exists and the ignition switch is OFF long enough in order to power down
the PCM.

DIAGNOSTIC AIDS
^ Ensure that the transmission linkage from the select lever to the manual valve is adjusted properly.
^ If a transmission overhaul was performed, ensure that the transmission fluid is at the proper level. A low fluid condition may set this DTC.
^ Inspect the TFP manual valve position switch seals for damage.
^ Inspect the TFP manual valve position switch for debris, or loose rivets.
^ Refer to the Transmission Fluid Temperature (TFT) Sensor Specifications table for the normal range signals and the invalid combinations.

TEST DESCRIPTION
The numbers below refer to the step numbers on the diagnostic table.
3. This step tests the indicated range signal to the manual valve range actually selected.
5. This step tests for correct voltage from the PCM to the transmission 20-way connector.
6. This step tests for a short together between signal circuit A and signal circuits B or C.
P1811

Diagnostic Chart 1 Of 3
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 527
Chevrolet Venture V6-3.4L VIN E 2207

Diagnostic Chart 2 Of 3
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 528
Chevrolet Venture V6-3.4L VIN E 2208

Diagnostic Chart 3 Of 3
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 529
Chevrolet Venture V6-3.4L VIN E 2209

Schematic

Circuit Description with 4T65-E Automatic Transaxle


The transmission pressure is modified by an adaptive modifier which controls the shift execution time. This test checks the time required to
accomplish the shift. If the shift takes longer than 0.65 seconds and the adaptive modifier cannot shorten this time, then a counter increases by
one.

If the PCM detects a counter value of two during one trip, then DTC P1811 sets. DTC P1811 is a type C DTC.

CONDITIONS FOR RUNNING THE DTC


^ The shift is adaptable.
^ The 1-2, the 2-3 or the 3-4 shift adapt cell has reached its limit.

CONDITIONS FOR SETTING THE DTC


The 1-2, 2-3 or 3-4 shift is longer than 0.65 seconds, twice in one trip.

ACTION TAKEN WHEN THE DTC SETS


^ The PCM does not illuminate the Malfunction Indicator Lamp (MIL).
^ The PCM commands maximum line pressure.
^ The PCM freezes shift adapts.
^ The PCM records the operating conditions when the Conditions for Setting the DTC are met. The PCM stores this information as Failure
Records.
^ The PCM stores DTC P1811 in PCM history.

CONDITIONS FOR CLEARING THE DTC


^ A scan tool can clear the DTC.
^ The PCM clears the DTC from PCM history if the vehicle completes 40 consecutive warm-up cycles without a non-emission-related
diagnostic fault occurring.
^ The PCM cancels the DTC default actions when the fault no longer exists and the ignition switch is OFF long enough in order to power down
the PCM.

DIAGNOSTIC AIDS
^ Ask the customer about possible overloading, exceeding the trailer towing limit or towing in overdrive.
^ Ensure that the PCM has the latest calibration update.
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 530
Chevrolet Venture V6-3.4L VIN E 2210

TEST DESCRIPTION
The numbers below refer to the step numbers on the diagnostic table.
7. This step inspects components that may cause low line pressure.
9. This step inspects or repairs components that may cause a maximum adapt and long 1-2 upshift.
11. This step inspects or repairs components that may cause a maximum adapt and long 2-3 upshift.
13. This step inspects or repairs components that may cause a maximum adapt and long 3-4 upshift.

P1814

Diagnostic Chart
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 531
Chevrolet Venture V6-3.4L VIN E 2211

Schematic

Circuit Description with 4T65-E Automatic Transaxle


This diagnostic test checks for unusually high throttle angle and low vehicle speed when the transmission is in DRIVE or REVERSE. The
primary purpose of this DTC is to record the Failure Record data, because this condition could damage the powertrain or create an unsafe
condition.

If the PCM detects an unusually high throttle angle and low vehicle speed when the transmission is in DRIVE or REVERSE, then DTC P1814
sets. DTC P1814 is a type C DTC.

CONDITIONS FOR RUNNING THE DTC


^ No TP sensor DTC P0121, P0122, or P0123.
^ No VSS DTC P0502 or P0503.
^ No TFP manual valve position switch DTC P1810.
^ The vehicle speed is less than 11 km/h (7 mph).
^ The transmission is in a DRIVE range or REVERSE.
^ The TP angle is 70 percent or greater.

CONDITIONS FOR SETTING THE DTC


The TCC slip speed is greater than 2100 RPM for 12 seconds.

ACTION TAKEN WHEN THE DTC SETS


^ The PCM does not illuminate the Malfunction Indicator Lamp (MIL).
^ The PCM records the operating conditions when the Conditions for Setting the DTC are met. The PCM stores this information as Failure
Records.
^ The PCM stores DTC P1814 in PCM history.

CONDITIONS FOR CLEARING THE DTC


^ A scan tool can clear the DTC.
^ The PCM clears the DTC from PCM history if the vehicle completes 40 consecutive warm-up cycles without a non-emission-related
diagnostic fault occurring.
^ The PCM cancels the DTC default actions when the fault no longer exists and the ignition switch is OFF long enough in order to power down
the PCM.
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 532
Chevrolet Venture V6-3.4L VIN E 2212

DIAGNOSTIC AIDS
A simultaneous acceleration and application of the brakes may cause DTC P1814 to occur.

TEST DESCRIPTION
The numbers below refer to the step numbers on the diagnostic table.
2. This step inspects the Failure Records for DTC P1814 occurrences.
4. This step replaces the fluid and the filter. If DTC P1814 occurs more than once in the Failure Records, severe TCC damage may have
occurred.
P1860

Diagnostic Chart 1 Of 3
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 533
Chevrolet Venture V6-3.4L VIN E 2213

Diagnostic Chart 2 Of 3
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 534
Chevrolet Venture V6-3.4L VIN E 2214

Diagnostic Chart 3 Of 3

Schematic
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 535
Chevrolet Venture V6-3.4L VIN E 2215
Circuit Description with 4T65-E Automatic Transaxle
Ignition voltage is provided to the Torque Converter Clutch Pulse Width Modulation (TCC PWM) solenoid valve. The PCM controls the
solenoid with a negative duty cycle in order to control application and release of the TCC. When the solenoid is commanded OFF, the PCM
senses high voltage. When the solenoid is commanded ON, the PCM senses low voltage.

DTC P1860 sets if the PCM detects a voltage that is outside of the calibration limits. DTC P1860 is a type B DTC.

CONDITIONS FOR RUNNING THE DTC


^ The system voltage is 9-18 volts.
^ The engine speed is greater than 500 RPM for 5 seconds and not in fuel shut off.

CONDITIONS FOR SETTING THE DTC


DTC P1860 sets when one of the following conditions exists for at least 5 seconds:
^ The PCM commands the solenoid to greater than 90% duty cycle and the voltage feedback remains high (B+) or:
^ The PCM commands the solenoid to less than 10% duty cycle and the voltage feedback remains low (0 volts).

ACTION TAKEN WHEN THE DTC SETS


^ The PCM illuminates the Malfunction Indicator Lamp (MIL) during the second consecutive trip in which the conditions for setting the DTC
are met.
^ The PCM inhibits TCC.
^ The PCM inhibits 4th gear if the transmission is in Hot Mode.
^ The PCM freezes shift adapts.
^ The PCM records the operating conditions when the Conditions for Setting the DTC are met. The PCM stores this information as Freeze
Frame and Failure Records.
^ The PCM stores DTC P1860 in PCM history during the second consecutive trip in which the conditions for setting the DTC are met.

CONDITIONS FOR CLEARING THE MIL/DTC


^ The PCM turns OFF the MIL during the third consecutive trip in which the diagnostic test runs and passes.
^ A scan tool can clear the MIL/DTC.
^ The PCM clears the DTC from the PCM history if the vehicle completes 40 consecutive warm-up cycles without an emission-related
diagnostic fault occurring.
^ The PCM cancels the DTC default actions when the fault no longer exists and the ignition switch is OFF long enough in order to power down
the PCM.

DIAGNOSTIC AIDS
^ Inspect the connectors at the controller, the component and all other circuit connecting points for an intermittent condition. Refer to Testing
for Intermittent and Poor Connections in Diagrams.
^ Inspect the circuit wiring for an intermittent condition. Refer to Testing for Electrical Intermittents in Diagrams.

TEST DESCRIPTION
The numbers below refer to the step numbers on the diagnostic table.
2. A short to ground in the power feed circuit to the solenoid ahead of the splice would open the fuse and set DTCs for other solenoids on the
same circuit. An open in the same circuit would not open the fuse but would set the other DTCs.

P1887
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 536
Chevrolet Venture V6-3.4L VIN E 2216

Diagnostic Chart 1 Of 2
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 537
Chevrolet Venture V6-3.4L VIN E 2217

Diagnostic Chart 2 Of 2
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 538
Chevrolet Venture V6-3.4L VIN E 2218

Schematic

Circuit Description with 4T65-E Automatic Transaxle


The TCC release switch is part of the Transmission Fluid Pressure (TFP) manual valve position switch. The TFP manual valve position switch is
mounted to the transmission valve body. The TCC release switch is normally-closed.

The switch signals the PCM that the TCC is released. This is accomplished by torque converter release fluid pressure acting on the switch contact
which opens the circuit. When the circuit voltage is high, the PCM recognizes that the TCC is no longer engaged.

If the PCM determines that the TCC release switch is open (indicating that the TCC is not applied) and the TCC slip speed indicates that the TCC
is applied, then DTC P1887 sets. DTC P1887 is a type B DTC.

CONDITIONS FOR RUNNING THE DTC


^ No AT ISS sensor DTC P0716 or P0717.
^ No TCC PWM solenoid valve DTC P0741 or P0742.
^ No TFP manual valve position switch DTC P1810.
^ The engine speed is greater than 500 RPM for 5 seconds and not in fuel shut off.
^ The transmission range selector is in D4.
^ The TCC is commanded ON.
^ The TCC pressure is 138-827 kPa (20-120 psi).
^ The TCC slip speed is -20 to +60 RPM.
^ The engine torque is 41-339 N.m (30-250 lb ft).

CONDITIONS FOR SETTING THE DTC


DTC P1887 sets when the following condition occurs twice in a single trip:

The TCC release pressure switch is open (indicating release pressure present) for 6 seconds continuous.

ACTION TAKEN WHEN THE DTC SETS


^ The PCM illuminates the Malfunction Indicator Lamp (MIL) during the second consecutive trip in which the conditions for setting the DTC
are met.
^ The PCM inhibits TCC.
^ The PCM inhibits 4th gear if the transmission is in Hot Mode.
^ The PCM freezes shift adapts.
^ The PCM records the operating conditions when the Conditions for Setting the DTC are met. The PCM stores this information as Freeze
Frame and Failure Records.
^ The PCM stores DTC P1887 in PCM history during the second consecutive trip in which the conditions for setting the DTC are met.

CONDITIONS FOR CLEARING THE MIL/DTC


^ The PCM turns OFF the MIL during the third consecutive trip in which the diagnostic test runs and passes.
^ A scan tool can clear the MIL/DTC.
^ The PCM clears the DTC from the PCM history if the vehicle completes 40 consecutive warm-up cycles without an emission-related
diagnostic fault occurring.
^ The PCM cancels the DTC default actions when the fault no longer exists and the ignition switch is OFF long enough in order to power down
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 539
Chevrolet Venture V6-3.4L VIN E 2219
the PCM.

DIAGNOSTIC AIDS
^ Inspect the connectors at the controller, the component and all other circuit connecting points for an intermittent condition. Refer to Testing
for Intermittent and Poor Connections in Diagrams.
^ Inspect the circuit wiring for an intermittent condition. Refer to Testing for Electrical Intermittents in Diagrams.

TEST DESCRIPTION
The numbers below refer to the step numbers on the diagnostic table.
3. This step tests the PCMs ability to recognize a grounded circuit.
4. A short to ground in this circuit would set DTC P0742.
5. A short to ground in this circuit would set DTC P0742
A Important Preliminary Checks
Before using the Symptom tables, perform the following procedures:

- Perform the A Powertrain On Board Diagnostic (OBD) System Check and verify all of the following items:
- The PCM and Malfunction Indicator Lamp (MIL) are operating correctly.
- DTCs are not stored.
- The scan tool data is within normal operating range. Refer to Scan Tool Data List.
- Verify the customer complaint.
- Perform the Visual/Physical Check. See: Initial Inspection and Diagnostic Overview
- Locate the correct symptom in the list at the end of this section. Follow the procedures in the appropriate diagnostic table. If the problem can
not be duplicated, refer to Intermittent Conditions. See: Initial Inspection and Diagnostic Overview/Diagnostic Strategies/Intermittent
Conditions

Backfire (Part 1 Of 3)
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 540
Chevrolet Venture V6-3.4L VIN E 2220

Backfire (Part 2 Of 3)

Backfire (Part 3 Of 3)
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 541
Chevrolet Venture V6-3.4L VIN E 2221

Cuts Out, Misses (Part 1 Of 3)


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 542
Chevrolet Venture V6-3.4L VIN E 2222

Cuts Out, Misses (Part 2 Of 3)


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 543
Chevrolet Venture V6-3.4L VIN E 2223

Cuts Out, Misses (Part 3 Of 3)


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 544
Chevrolet Venture V6-3.4L VIN E 2224

Detonation/Spark Knock (Part 1 Of 2)


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 545
Chevrolet Venture V6-3.4L VIN E 2225

Detonation/Spark Knock (Part 2 Of 2)

Dieseling, Run-On

Engine Cranks But Does Not Run


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 546
Chevrolet Venture V6-3.4L VIN E 2226

Diagnostic Chart

Refer to Engine Controls Schematics. See: Diagrams/Electrical Diagrams

CIRCUIT DESCRIPTION
When the ignition switch is first turned ON, the PCM energizes the fuel pump relay which applies power to the in-tank fuel pump. The fuel
pump relay will remain on as long as the engine is running or cranking and the PCM is receiving 3X reference pulses. If no 3X reference pulses
are present, the PCM de-energizes the fuel pump relay within 2 seconds after the ignition is turned ON, or the engine is stopped.

During cranking, the ignition control module monitors the 7X crankshaft position sensor input for recognition of the sync signal. The sync signal
is used to determine the correct cylinder pair to spark first. After the sync signal has been processed by the ignition control module, it sends a 3X
reference signal to the PCM. When the PCM receives this signal it will command all six injectors to open for one priming shot of fuel in all
cylinders. After the priming, the injectors are left off for the next six 3X reference signals from the ignition control module (two crankshaft
revolutions). This allows each cylinder to use the fuel from the priming shot. During this waiting period, a cam signal will have been received by
the PCM. After the true camshaft position is detected, the PCM operates the injectors sequentially. However, if the cam signal is not present at
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 547
Chevrolet Venture V6-3.4L VIN E 2227
start-up, DTC P0341 Camshaft Position (CMP) Sensor Performance will set and the PCM will start sequential fuel delivery in random pattern
with a 1 in 6 chance that fuel delivery is correct.

The sync signal is used only by the ignition control module. It is used for spark synchronization at start-up only (not passed to the PCM).

DIAGNOSTIC AIDS
Inspect for the following:
- Mass Air Flow is compared to a calculated Mass Air Flow based upon the MAP, TP, and engine RPM readings (speed density). A
Skewed/unresponsive MAP sensor at KEY on will cause the predicted air flow value to be inaccurate. Compare MAP and TP sensor value to
that of a known good vehicle.
- Faulty Engine Coolant Temperature Sensor. Using a scan tool, compare Engine Coolant Temperature with Intake Air Temperature on a
completely cool engine. Engine Coolant Temperature should be within 10°C of Intake Air Temperature. If not, replace the ECT sensor.

IMPORTANT: Remove any debris from the connector surfaces before servicing a component. Inspect the connector gaskets when diagnosing
or replacing a component. Ensure that the gaskets are installed correctly. The gaskets prevent contaminate intrusion.

- Poor terminal connection-Inspect the harness connectors for backed out terminals, improper mating, broken locks, improperly formed or
damaged terminals, and faulty terminal to wire connection. Use a corresponding mating terminal to test for proper tension. Refer to
Diagrams.
- Damaged harness-Inspect the wiring harness for damage. If the harness inspection does not reveal a problem, observe the display on the scan
tool while moving connectors and wiring harnesses related to the sensor. A change in the scan tool display may indicate the location of the
fault. Refer to Diagrams.
- PCM and engine grounds for clean and secure connections

If the DTC is determined to be intermittent, reviewing the Failure Records can be useful in determining when the DTC was last set.

TEST DESCRIPTION
The numbers below refer to the step numbers on the Diagnostic Table:
5. Testing for spark at an ignition wire will determine if the problem is with the 7X crankshaft position sensor input to the IC Module. By using
J 26792 Spark Tester to test for spark at the ignition coil towers, each ignition coils ability to produce at least 25,000 volts is verified.
6. A blinking J 34730-380 Injector Load Tester LEDs verifies that the PCM is capable of activating the injectors.

A non-blinking J 34730-380 Injector Load Tester LEDs indicates a possible fault condition in the fuel injector circuits.
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 548
Chevrolet Venture V6-3.4L VIN E 2228

Hard Start (Part 1 Of 2)


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 549
Chevrolet Venture V6-3.4L VIN E 2229

Hard Start (Part 2 Of 2)


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 550
Chevrolet Venture V6-3.4L VIN E 2230

Hesitation, Sag, Stumble (Part 1 Of 2)


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 551
Chevrolet Venture V6-3.4L VIN E 2231

Hesitation,Sag,Stumble (Part 2 Of 2)
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 552
Chevrolet Venture V6-3.4L VIN E 2232

Intermittent Conditions (Part 1 Of 3)


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 553
Chevrolet Venture V6-3.4L VIN E 2233

Intermittent Conditions (Part 2 Of 3)


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 554
Chevrolet Venture V6-3.4L VIN E 2234

Intermittent Conditions (Part 3 Of 3)


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 555
Chevrolet Venture V6-3.4L VIN E 2235

Lack Of Power, Sluggishness, Or Sponginess (Part 1 Of 2)


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 556
Chevrolet Venture V6-3.4L VIN E 2236

Lack Of Power, Sluggishness, Or Sponginess (Part 2 Of 2)

Malfunction Indicator Lamp (MIL) Always On


SYSTEM DESCRIPTION
The Powertrain On Board Diagnostic (OBD) System Check must be the starting point for any driveability complaint diagnosis. See: Initial
Inspection and Diagnostic Overview

Perform a careful visual/physical check of the PCM and engine grounds for being clean and tight. Refer to Visual/Physical Check in Symptoms.
See: Initial Inspection and Diagnostic Overview

A Powertrain On Board Diagnostic (OBD) System Check is an organized approach to identifying a problem created by an electronic engine
control system malfunction.

The Powertrain Control Module (PCM) controls the MIL by providing a ground path through the MIL control circuit to turn on the MIL. When
the ignition is turned on, the MIL will remain on until the engine is running, if no Diagnostic Trouble Codes (DTC) are stored. If the MIL is
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 557
Chevrolet Venture V6-3.4L VIN E 2237
illuminated, then the engine stalls, the MIL will remain illuminated so long as the ignition switch is on. DTC P0650 Malfunction Indicator Lamp
(MIL) Control Circuit set suggests a malfunction in the MIL driver circuit.

Malfunction Indicator Lamp (MIL) Inoperative

Diagnostic Chart (Part 1 Of 2)


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 558
Chevrolet Venture V6-3.4L VIN E 2238

Diagnostic Chart (Part 2 Of 2)


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 559
Chevrolet Venture V6-3.4L VIN E 2239

Schematic

CIRCUIT DESCRIPTION
There should be a steady MIL with the ignition ON and the engine not running. Ignition feed voltage is supplied directly to the MIL. The
Powertrain Control Module (PCM) turns the MIL ON by grounding the MIL control circuit. No MIL with the key ON, engine not running and
the MIL DTC set suggests an open in the MIL control circuit.

MIL OPERATION
The Malfunction Indicator Lamp (MIL) is located on the instrument panel and is displayed as CHECK ENGINE lamp.

MIL FUNCTION
- The MIL informs the driver that a malfunction has occurred and the vehicle should be taken in for service as soon as possible
- The MIL illuminates during a bulb test and a system test
- A DTC will be stored if a MIL is requested by the diagnostic

MIL ILLUMINATION
- The MIL will illuminate with ignition switch ON and the engine not running
- The MIL will turn OFF when the engine is started
- The MIL will remain ON if the self-diagnostic system has detected a malfunction
- The MIL may turn OFF if the malfunction is not present
- If the MIL is illuminated and then the engine stalls, the MIL will remain illuminated so long as the ignition switch is ON.
- If the MIL is not illuminated and the engine stalls, the MIL will not illuminate until the ignition switch is cycled OFF, then ON.

POWERTRAIN ON BOARD DIAGNOSTIC (OBD) SYSTEM CHECK


Perform the Powertrain On Board Diagnostic (OBD) System Check, when the following conditions are present:
- When the MIL does not turn ON when the ignition switch is turned to the RUN position. See above for MIL Operation
- When the MIL remains ON while the engine is running
- When the MIL is flashing while the engine is running
- When a driveability symptom is determined

DIAGNOSTIC AIDS
Inspect the following items:
- If the engine runs OK, inspect for a malfunctioning MIL, an open in the MIL control circuit, or an open in the instrument cluster ignition
teed.
- If the engine cranks but will not run, inspect for an open PCM ignition or battery feed or a faulty PCM to engine ground.

IMPORTANT: Remove any debris from the connector surfaces before servicing a component. Inspect the connector gaskets when diagnosing
or replacing a component. Ensure that the gaskets are installed correctly. The gaskets prevent contaminate intrusion.
- Poor terminal connection-Inspect the harness connectors for backed out terminals, improper mating, broken locks, improperly formed or
damaged terminals, and faulty terminal to wire connection. Use a corresponding mating terminal to test for proper tension. Refer to
Diagrams.
- Damaged harness-Inspect the wiring harness for damage. If the harness inspection does not reveal a problem, observe the display on the scan
tool while moving connectors and wiring harnesses related to the sensor. A change in the scan tool display may indicate the location of the
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 560
Chevrolet Venture V6-3.4L VIN E 2240
fault. Refer to Diagrams.
- PCM and engine grounds for clean and secure connections

If the DTC is determined to be intermittent, reviewing the Failure Records can be useful in determining when the DTC was last set.

The numbers below refer to the step numbers on the diagnostic table:
2. A no MIL condition accompanied by a no start condition suggests a faulty PCM ignition feed or battery feed circuit.
9. Using a test lamp connected to battery positive voltage, probe each of the PCM ground terminals to ensure that a good ground is present.
16. This vehicle is equipped with a PCM which utilizes an Electrically Erasable Programmable Read Only Memory (EEPROM). When the PCM
is being replaced, the new PCM must be programmed.

Poor Fuel Economy (Part 1 Of 2)


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 561
Chevrolet Venture V6-3.4L VIN E 2241

Poor Fuel Economy (Part 2 Of 2)


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 562
Chevrolet Venture V6-3.4L VIN E 2242

Poor Fuel Fill Quality


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 563
Chevrolet Venture V6-3.4L VIN E 2243

Rough, Unstable, Or Incorrect Idle And Stalling (Part 1 Of 3)


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 564
Chevrolet Venture V6-3.4L VIN E 2244

Rough, Unstable, Or Incorrect Idle And Stalling (Part 2 Of 3)


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 565
Chevrolet Venture V6-3.4L VIN E 2245

Rough,Unstable, Or Incorrect Idle And Stalling (Part 3 Of 3)

Scan Tool Does Not Communicate


For Scan Tool Does Not Communicate Diagnostics go to the component - Information Bus See: Information Bus/Testing and Inspection/Symptom
Related Diagnostic Procedures
Scan Tool Does Not Power Up
For Scan Tool Does Not Power Up Diagnostics go to the component - Information Bus See: Information Bus/Testing and Inspection/Symptom
Related Diagnostic Procedures

Surges/Chuggles 1 Of 2
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 566
Chevrolet Venture V6-3.4L VIN E 2246

Surges/Chuggles (Part 2 Of 2)

Fuel Quality Diagnosis


Alcohol concentrations more than 10 percent in fuel can be detrimental to fuel system components and may cause driveability problems such as
hesitation, lack of power, stall, no start, etc.

The problems may be due to fuel system corrosion and subsequent fuel filter plugging, deterioration of rubber components, and/or air-fuel mixture
leaning.

Various types and concentrations of alcohol are used in commercial fuel. Some alcohol is more detrimental to fuel system components than others.
If an excessive amount of alcohol in the fuel is suspected as the cause of a driveability condition.

ALCOHOL IN FUEL TESTING PROCEDURE


The fuel sample should be drawn from the bottom of the tank so that any water present in the tank will be detected. The sample should be bright
and clear. If alcohol contamination is suspected then use the following procedure to test the fuel quality.
1. Using a 100 ml specified cylinder with 1 ml graduation marks, fill the cylinder with fuel to the 90 ml mark.
2. Add 10 ml of water in order to bring the total fluid volume to 100 ml and install a stopper.
3. Shake the cylinder vigorously for 10 to 15 seconds.
4. Carefully loosen the stopper in order to release the pressure.
5. Re-install the stopper and shake the cylinder vigorously again for 10 to 15 seconds.
6. Put the cylinder on a level surface for approximately 5 minutes in order to allow adequate liquid separation.

If alcohol is present in the fuel, the volume of the lower layer (which would now contain both alcohol and water) will be more than 10 ml. For
example, if the volume of the lower layer is increased to 15 ml, this indicates at least 5 percent alcohol in the fuel. The actual amount of alcohol
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 567
Chevrolet Venture V6-3.4L VIN E 2247
may be somewhat more because this procedure does not extract all of the alcohol from the fuel.

PHYSICAL CONTAMINANTS IN FUEL TESTING PROCEDURE


The fuel sample should be drawn from the bottom of the tank so that any water present in the tank will be detected. The sample should be bright
and clear. If the sample appears cloudy, or contaminated with water (as indicated by a water layer at the bottom of the sample) use the following
procedure to diagnose the fuel.
1. Using an approved fuel container, draw approximately 0.5 liter of fuel.
2. Place the cylinder on a level surface for approximately 5 minutes in order to allow settling of the particulate contamination.
3. Observe the fuel sample. If any physical contaminants or water are present, then clean the fuel system. Refer to Fuel System Cleaning in Fuel
Delivery and Air Induction.

Particulate contamination will show up in various shapes and colors, such as sand will typically be identified by a white or light brown crystals,
rubber particles typically as black and irregular. Any particles that do show up regardless of color or shape are not acceptable, and the entire fuel
system should be thoroughly cleaned.

Results of Incorrect Operation


- A plugged valve or hose may cause the following conditions:
- Rough idle
- Stalling or slow idle speed
- Oil leaks
- Oil in the air cleaner
- Sludge in the engine
- A leaking crankcase ventilation valve or hose may cause the following conditions:
- Rough idle
- Stalling
- High idle speed

Functional Check

With these systems, any blow-by in excess of the system capacity (from a badly worn engine, sustained heavy load, etc.) is exhausted into the air
intake passages and is drawn into the engine.

Proper operation of the crankcase ventilation system depends upon a sealed engine. If oil slugging or dilution is noted and the crankcase ventilation
system is functioning properly, inspect the engine for a possible cause. Correct any problems.

If an engine is idling rough, inspect for a clogged crankcase ventilation valve, a dirty vent filter or air cleaner element, or a plugged hose. Replace
any components as required. Use the following procedure:
1. Remove the crankcase ventilation valve from the rocker arm cover.
2. Operate the engine at idle.
3. Place your thumb over the end of the valve in order to feel for a vacuum. If there is no vacuum at the valve, inspect the following items:
- The hoses
- The manifold port
- The crankcase ventilation valve
4. Turn OFF the engine. Remove the crankcase ventilation valve. Shake the valve. Listen for the rattle of the check needle inside of the valve. If
valve does not rattle, replace the valve.

Cooling Fan Functional Check


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 568
Chevrolet Venture V6-3.4L VIN E 2248

Diagnostic Chart

Refer to Engine Controls Schematics. See: Diagrams/Electrical Diagrams

Refer to Engine Controls Schematics Coolant Fans. See: Diagrams/Electrical Diagrams

CIRCUIT DESCRIPTION
Power for the fan motors is supplied through the Cool Fan 1 Maxi Fuse(R) 30A and the Cool Fan 2 Maxi Fuse(R) 30A in the Underhood
Accessory Wiring Junction Block. The cooling fan relays are energized when current flows from the 2 Maxifuses(R) through the relay coils to
ground through the powertrain control module (PCM). The Cool Fan 1 Relay Control Circuit is grounded for low speed fans operation. The
Cool Fan 1 Relay Control Circuit and the Cool Fan 2 Relay Control Circuit are both grounded for high speed fans operation.

During low speed fans operation the PCM supplies a ground path for the Cool Fan 1 Relay. This closes the Cool Fan 1 Relay contacts, allowing
current to flow from the Underhood Accessory Wiring Junction Block through the relay contacts to the Engine Coolant Fan Motor 1 RH. During
low speed operation, the ground path for the Engine Coolant Fan Motor 1 RH is through the Coolant Fan 1 Relay and the Engine Coolant Fan
Motor 2 LH. The result is a series circuit with both cooling fans running at low speed. During high speed cooling fan operation the PCM supplies
a ground path for the Cool Fan 1 Relay. The PCM also supplies a ground path for the Cool Fan Relay and the Cool Fan 2 Relay. This closes all 3
cooling fan relays. During high speed fans operation, both the Engine Coolant Fan Motor 1 RH and the Engine Coolant Fan Motor 2 LH are
supplied current from the Underhood Accessory wiring Junction Block and each cooling fan has its own ground path.

TEST DESCRIPTION
The numbers below refer to numbers on the diagnostic table:
2. The PCM will enable the engine cooling fans when certain Diagnostic Trouble Codes are set. Go to applicable DTC Table first before
proceeding with this table. See: Diagnostic Trouble Code Tests and Associated Procedures
3. Allow engine coolant temperature to cool below 100°C (212°F) before proceeding with diagnosis.
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 569
Chevrolet Venture V6-3.4L VIN E 2249

Electric Cooling Fan Table #1


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 570
Chevrolet Venture V6-3.4L VIN E 2250

Electric Cooling Fan Table #2 (Part 1 Of 2)


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 571
Chevrolet Venture V6-3.4L VIN E 2251

Electric Cooling Fan Table #2 (Part 2 Of 2)


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 572
Chevrolet Venture V6-3.4L VIN E 2252

Electric Cooling Fan Table #3 (Part 1 Of 2)


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 573
Chevrolet Venture V6-3.4L VIN E 2253

Electric Cooling Fan Table #3 (Part 2 Of 2)

Electronic Ignition (EI) System Diagnosis


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 574
Chevrolet Venture V6-3.4L VIN E 2254

Diagnostic Chart (Part 1 Of 2)


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 575
Chevrolet Venture V6-3.4L VIN E 2255

Diagnostic Chart (Part 2 Of 2)

Refer to Engine Controls Schematics Ignition System, Knock Sensor. See: Diagrams/Electrical Diagrams

CIRCUIT DESCRIPTION
During cranking, the IC Module monitors the 7X CKP sensor input for recognition of the sync signal. The sync signal is used only by the IC
Module for synchronization at start-up to determine the correct cylinder pair to spark. Once the engine speed reaches approximately 600 RPM
the PCM sends 5.0 V to the bypass control circuit at the IC Control Module causing the IC control circuit to become ungrounded allowing the
24X signal to be used for better low engine speed performance. At higher engine speeds (1650+) the PCM uses the 3X reference pulses to
control ignition timing because a higher resolution signal is not needed.

Conventional ignition coils have one end of the secondary winding connected to the engine ground. In this ignition system, neither end of the
secondary winding is grounded. Instead, each end of a coil's secondary winding is attached to a spark plug. Each cylinder is paired with the
cylinder that is opposite it (1-4, 2-5, 3-6). These two plugs are on companion cylinders, i.e., on top dead center at the same time. When the coil
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 576
Chevrolet Venture V6-3.4L VIN E 2256
discharges, both plugs fire at the same time to complete the series circuit. The cylinder on compression is said to be the event cylinder and the
one on exhaust is the waste cylinder. The cylinder on the exhaust stroke requires very little of the available energy to fire the spark plug. The
remaining energy will be used as required by the cylinder on the compression stroke. The same process is repeated when the cylinders reverse
roles. This method of ignition is called a waste spark ignition system.

This table assumes there are no Ignition System, Fuel Injector, Cam Sensor, or Crank Sensor DTC's present. The Electronic Ignition System
Check tests for faulty ignition coils, spark plugs, plug wires, the 7X Crank Sensor, and IC Module. This table requires the J 26792 Spark Tester.

DIAGNOSTIC AIDS
Inspect for the following conditions:

IMPORTANT: Remove any debris from the connector surfaces before servicing a component. Inspect the connector gaskets when diagnosing
or replacing a component. Ensure that the gaskets are installed correctly. The gaskets prevent contaminate intrusion.

- Poor terminal connection-Inspect the harness connectors for backed out terminals, improper mating, broken locks, improperly formed or
damaged terminals, and faulty terminal to wire connection. Use a corresponding mating terminal to test for proper tension. Refer to
Diagrams.
- Damaged harness-Inspect the wiring harness for damage. If the harness inspection does not reveal a problem, observe the display on the scan
tool while moving connectors and wiring harnesses related to the sensor. A change in the scan tool display may indicate the location of the
fault. Refer to Diagrams.
- PCM and engine grounds for clean and secure connections

If the DTC is determined to be intermittent, reviewing the Failure Records can be useful in determining when the DTC was last set.

TEST DESCRIPTION
Numbers below refer to the step numbers on the Diagnostic Table:
2. It is necessary to disconnect the 24X Crank Sensor to ensure that the 7X signal is being read in the 3X reference parameter on the scan tool.
3. The J 26792 spark tester presents a more difficult load on the secondary ignition than a normal spark plug. If a miss, stumble, or hesitation is
being caused by a spark plug not firing, the spark tester should also not fire.
4. Use a 5% saltwater solution in a spray bottle to induce voltage arching to ground through faulty insulation of spark plug wires.
6. If the no spark condition follows the suspected coil, that coil is faulty. Otherwise, the ignition module is the cause of no spark. This test could
also be performed by substituting a known good coil for the one causing the no spark condition.

Engine Oil Level Sensor/Switch Diagnosis


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 577
Chevrolet Venture V6-3.4L VIN E 2257

Diagnostic Chart
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 578
Chevrolet Venture V6-3.4L VIN E 2258

Schematic

CIRCUIT DESCRIPTION
The Engine Oil Level (EOL) switch is a simple float switch that is grounded when the engine oil level is OK. The PCM tests the EOL switch
circuit at start-up. Before checking the state of the EOL switch, the PCM performs a test routine based on time and Engine Coolant Temperature
(ECT) to ensure that the engine oil has drained back into the sump. To test for low oil level at start-up, one of the following conditions must be
present:
- The ECT must be more than 15°C (59°F)
- The ECT at key ON must be at least 12°C (22°F) cooler than the ECT at the last key OFF.

The low oil level lamp will be illuminated for about a minute when the PCM tests for low oil level and the EOL switch indicates that a low oil
level condition exists (EOL switch circuit not grounded). When the ignition is first turned ON, the IP Cluster commands the low oil level lamp
ON for a brief period of time to test the bulb.

DIAGNOSTIC AIDS
Inspect for the following conditions:

IMPORTANT: Remove any debris from the connector surfaces before servicing a component. Inspect the connector gaskets when diagnosing
or replacing a component. Ensure that the gaskets are installed correctly. The gaskets prevent contaminate intrusion.

- Poor terminal connection-Inspect the harness connectors for backed out terminals, improper mating, broken locks, improperly formed or
damaged terminals, and faulty terminal to wire connection. Use a corresponding mating terminal to test for proper tension. Refer to
Diagrams.
- Damaged harness-Inspect the wiring harness for damage. If the harness inspection does not reveal a problem, observe the display on the scan
tool while moving connectors and wiring harnesses related to the sensor. A change in the scan tool display may indicate the location of the
fault. Refer to Diagrams.
- PCM and engine grounds for clean and secure connections

If the DTC is determined to be intermittent, reviewing the Failure Records can be useful in determining when the DTC was last set.

TEST DESCRIPTION
The numbers below refer to the step numbers on the diagnostic table:
11. This vehicle is equipped with a PCM which utilizes an Electrically Erasable Programmable Read Only Memory (EEPROM). When the PCM
is being replaced, the new PCM must be programmed.
12. For the PCM to test engine oil level, start-up ECT must be at least 12°C (22°F) cooler than the ECT was last time the ignition was turned off.
Allowing the engine to warm and then cool ensures that the PCM tests the engine oil level switch and that the information displayed on the
scan tool is current.

Engine Oil Pressure Sensor/Switch Diagnosis


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 579
Chevrolet Venture V6-3.4L VIN E 2259

Diagnostic Chart

Refer to Engine Controls Schematic IAC, Engine Oil Level, Engine Oil Pressure, EGR, EVAP vent. See: Diagrams/Electrical Diagrams

CIRCUIT DESCRIPTION
The PCM applies battery voltage through a pull up resistor to the Engine Oil Pressure Switch circuit. The PCM monitors the applied voltage on
the Engine Oil Pressure Switch circuit. If the ignition switch is turned ON with the engine not running or engine oil pressure is below 35 kPa (5
psi), the Engine Oil Pressure switch grounds the PCM voltage input. The PCM sends the engine oil pressure information via Class II serial data
to the Instrument Panel (IP) Cluster. The IP Cluster controls the Engine Oil Pressure Indicator.

DIAGNOSTIC AIDS
Inspect the following:

IMPORTANT: Remove any debris from the connector surfaces before servicing a component. Inspect the connector gaskets when diagnosing
or replacing a component. Ensure that the gaskets are installed correctly. The gaskets prevent contaminate intrusion.

- Poor terminal connection-Inspect the harness connectors for backed out terminals, improper mating, broken locks, improperly formed or
damaged terminals, and faulty terminal to wire connection. Use a corresponding mating terminal to test for proper tension. Refer to
Diagrams.
- Damaged harness-Inspect the wiring harness for damage. If the harness inspection does not reveal a problem, observe the display on the scan
tool while moving connectors and wiring harnesses related to the sensor. A change in the scan tool display may indicate the location of the
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 580
Chevrolet Venture V6-3.4L VIN E 2260
fault. Refer to Diagrams.
- PCM and engine grounds for clean and secure connections

If the DTC is determined to be intermittent, reviewing the Failure Records can be useful in determining when the DTC was last set.

Evaporative Emission (EVAP) Control System Diagnosis

Diagnostic Chart (Part 1 Of 2)


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 581
Chevrolet Venture V6-3.4L VIN E 2261

Diagnostic Chart (Part 2 Of 2)

Refer to Emission Hose Routing Diagram, EVAP SYSTEM OVERVIEW.See: Emission Control Systems

SYSTEM DESCRIPTION
The EVAP canister purge valve allows manifold vacuum to purge the canister. The Powertrain Control Module (PCM) supplies a Ground to
energize the purge valve (purge ON). The EVAP purge valve control is Pulse Width Modulated (PWM) or Turned ON and OFF several times a
second. The duty cycle (pulse width) is determined by engine operating conditions including load, throttle position, coolant temperature and
ambient temperature. The duty cycle is calculated by the PCM and the output is commanded when the appropriate conditions have been met.

The EVAP Vent valve is used to seal the EVAP system during diagnostic tests. The fuel tank pressure sensor is used to monitor vacuum in the
system during the diagnostic tests.

A stuck closed EVAP canister purge valve, Stuck open EVAP vent valve, disconnected or damaged EVAP Purge line or vent hose, leaking fuel
cap, or fill neck should set a DTC P0440. A small leak in the EVAP system should set a DTC P0442. An EVAP vent valve stuck closed, a
restricted vent hose, or a blocked EVAP canister should set a DTC P0446.A continuous purge condition with no purge commanded by the PCM
(EVAP purge valve stuck open or leaking) should set a DTC P1441. Refer to the DTC tables for further diagnostic procedures regarding the
EVAP system. See: Diagnostic Trouble Code Tests and Associated Procedures

The EVAP system includes the following components:


- The EVAP canister.
- The EVAP canister purge valve.
- The EVAP vent valve.
- The EVAP vapor pipes.
- The EVAP purge pipes.
- The EVAP fresh air vent hose.
- The fuel tank.
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 582
Chevrolet Venture V6-3.4L VIN E 2262
- The fuel pipes and hoses.
- The fuel fill cap.
- The fuel fill pipe.

DIAGNOSTIC AIDS
Check for the following conditions:
- Cracked or punctured EVAP canister.
- Damaged or disconnected source vacuum line, EVAP purge line, vent hose or fuel tank vapor line.
- Poor connection at the PCM.
- Inspect harness connectors for backed out terminals, improper mating, broken locks, improperly formed or damaged terminals, and poor
terminal to wire connection.
- Damaged harness. Inspect the wiring harness to the EVAP vent valve, the EVAP purge valve, and the fuel tank pressure sensor for an
intermittent open or short circuit.
- Kinked, pinched or plugged vacuum source, EVAP purge, or fuel tank vapor line. Verify that the lines are not restricted.
- Carbon being released into the system.

Fuel Injector Balance Test With Tech 2

Diagnostic Chart (Part 1 Of 2)


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 583
Chevrolet Venture V6-3.4L VIN E 2263

Diagnostic Chart (Part 2 Of 2)

CIRCUIT DESCRIPTION
The scan tool first energizes the fuel pump and then the injectors for a precise amount of time allowing a measured amount of fuel into the
manifold. This causes a drop in system fuel pressure that can be recorded and used to compare each injector.

TEST DESCRIPTION

CAUTION: Wrap a shop towel around the fuel pressure connection in order to reduce the risk of fire and personal injury. The towel
will absorb any fuel leakage that occurs during the connection of the fuel pressure gauge. Place the towel in an approved container when
the connection of the fuel pressure gauge is complete.

3. The engine coolant temperature must be below the operating temperature in order to avoid irregular fuel pressure readings due to hot soak
fuel boiling.
4. The fuel pressure should be within the specified range. If the fuel pressure is not within the specified range.
5. The fuel pressure should reach a steady value. If the fuel pressure does not reach a steady value.
6. If the pressure drop value for each fuel injector is within 10 kPa (1.5 psi) of the average pressure drop value, the fuel injectors are flowing
properly. Calculate the pressure drop value for each fuel injector by subtracting the second pressure reading from the first pressure reading.

Fuel Injector Balance Test With Special Tool


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 584
Chevrolet Venture V6-3.4L VIN E 2264

Diagnostic Chart (Part 1 Of 2)


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 585
Chevrolet Venture V6-3.4L VIN E 2265

Diagnostic Chart (Part 2 Of 2)

Injector Balance Test Example

TEST DESCRIPTION
Numbers below refer to the step numbers on the diagnostic table.
3. The engine coolant temperature must be below the operating temperature in order to avoid irregular fuel pressure readings due to Hot Soak
fuel boiling.
4. Tests the ability to achieve a specified fuel pressure range.
5. Tests the ability to maintain a steady fuel pressure value.
6. If the pressure drop value for each fuel injector is within 10 kPa (1.5 psi) of the average pressure drop value, the fuel injectors are flowing
properly. Calculate the pressure drop value for each fuel injector by subtracting the second pressure reading from the first pressure reading.
Refer to the Injector Balance Test Example.

ECT Between 10-35 Degrees C (50-95 Degrees F)


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 586
Chevrolet Venture V6-3.4L VIN E 2266

Diagnostic Chart

Example

CIRCUIT DESCRIPTION
The Powertrain Control Module (PCM) controls the fuel injector control circuit using a Multi Function Driver (MFD). Power is supplied from
the injector fuse to the injector and is grounded by the PCM. The MFD controls the injector ground, allowing fuel flow to pulse.

DIAGNOSTIC AIDS
Test the engine fuel injection harness for the following conditions:
- Poor Terminal Connection.
Inspect the harness connectors for backed out terminals, improper mating, broken locks improperly formed or damaged terminals and faulty
terminal to wire connection. Use a corresponding mating terminal to test for proper tension. Refer to Testing for Intermittent and Poor
Connections and Connector Repairs in Diagrams.
- Damaged harness.
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 587
Chevrolet Venture V6-3.4L VIN E 2267
Inspect the wiring harness for damage. Refer to Wiring Repairs in Diagrams.

TEST DESCRIPTION
Numbers below refer to the step numbers on the Diagnostic Table.
2. The engine coolant temperature affects the resistance in the fuel injector and the ability of the fuel injector tester to detect a faulty fuel
injector. If the engine coolant temperature is between the specified value, go to Fuel Injection Coil Test - ECT Outside 10°C-35°C. See:
Component Tests and General Diagnostics/Fuel Injector Coil Test/ECT Outside 10-35 Degrees C (50-95 Degrees F)
3. The first second of the voltage displayed by the Digital Multimeter (DMM) may be inaccurate due to the initial current surge. Therefore,
record the lowest voltage displayed by the DMM after the first second. The voltage displayed by the DMM should be within the specified
value (refer to the Example). The voltage displayed by the DMM may increase throughout the test as the fuel injectors windings warm and
the resistance changes. An erratic reading indicates an intermittent connection within the fuel injector and the fuel injector must be replaced.
A fuel injector outside the specified value is considered faulty and must be replaced.

ECT Outside 10-35 Degrees C (50-95 Degrees F)

Diagnostic Chart
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 588
Chevrolet Venture V6-3.4L VIN E 2268

Example

CIRCUIT DESCRIPTION
The Powertrain Control Module (PCM) controls the fuel injector control circuit using a Multi Function Driver (MFD). Power is supplied by the
injector fuse to the injector and is grounded by the PCM. The MFD controls the injector ground, allowing fuel flow to pulse.

DIAGNOSTIC AIDS
Test the engine fuel injection harness for the following conditions:
- Poor terminal connection.
Inspect the harness connectors for backed out terminals, improper mating, broken locks, improperly formed or damaged and faulty terminal
to wire connections. Use a corresponding mating terminal to test for proper tension. Refer to Testing for Intermittent and Poor Connections
and Connector Repairs in Diagrams.
- Damaged harness.
Inspect the wiring harness for damage. Refer to Wiring Repairs in Diagrams.

TEST DESCRIPTION
Numbers below refer to the step numbers on the Diagnostic Table.
2. The engine coolant temperature affects the resistance in the fuel injector and the ability of the fuel injector tester to detect a faulty fuel
injector. If the engine coolant temperature is between the specified value, go to Fuel Injection Coil Test - ECT Between 10°C-35°C. See:
Component Tests and General Diagnostics/Fuel Injector Coil Test/ECT Between 10-35 Degrees C (50-95 Degrees F)
3. The first second of the voltage displayed by the Digital Multimeter (DMM) may be inaccurate due to the initial current surge. Therefore,
record the lowest voltage displayed by the DMM after the first second. The voltage displayed by the DMM may increase throughout the test
as the fuel injector windings warm and the resistance of the fuel injector windings change. An erratic voltage reading (large fluctuations in
voltage that does not stabilize indicates an intermittent connection within the fuel injector. From the voltages recorded, identify the highest
voltage, excluding any voltages above 9.5 volts. A fuel injector with a recorded voltage above 9.5 volts is also considered faulty and must be
replaced.
4. Subtract each voltage from the highest recorded voltage below 9.5 volts. Record each subtracted value (refer to the Example). The subtracted
value for any fuel injector must not exceed 0.6 volt. A fuel injector with a subtracted value that is greater than the specified value is
considered faulty and must be replaced.

Fuel Pump Electrical Circuit Diagnosis


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 589
Chevrolet Venture V6-3.4L VIN E 2269

Diagnostic Chart (Part 1 Of 3)


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 590
Chevrolet Venture V6-3.4L VIN E 2270

Diagnostic Chart (Part 2 Of 3)


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 591
Chevrolet Venture V6-3.4L VIN E 2271

Diagnostic Chart (Part 3 Of 3)

Schematic
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 592
Chevrolet Venture V6-3.4L VIN E 2272

CIRCUIT DESCRIPTION
When the ignition switch is first turned on, the PCM energizes the fuel pump relay which applies power to the in-tank fuel pump. The fuel pump
relay will remain on as long as the engine is running or cranking and the PCM is receiving reference pulses. If no reference pulses are present,
the PCM de-energizes the fuel pump relay within 2 seconds after the ignition is turned on or the engine is stopped.

The fuel pump delivers fuel to the fuel rail and injectors, then to the fuel pressure regulator. The fuel pressure regulator controls fuel pressure by
allowing excess fuel to be returned to the fuel tank.

DIAGNOSTIC AIDS
Inspect for the following:

IMPORTANT: Remove any debris from the connector surfaces before servicing a component. Inspect the connector gaskets when diagnosing
or replacing a component. Ensure that the gaskets are installed correctly. The gaskets prevent contaminate intrusion.

- Poor terminal connection-Inspect the harness connectors for backed out terminals, improper mating, broken locks, improperly formed or
damaged terminals, and faulty terminal to wire connection. Use a corresponding mating terminal to test for proper tension. Refer to
Diagrams.
- Damaged harness-Inspect the wiring harness for damage. If the harness inspection does not reveal a problem, observe the display on the scan
tool while moving connectors and wiring harnesses related to the sensor. A change in the scan tool display may indicate the location of the
fault. Refer to Diagrams.
- PCM and engine grounds for clean and secure connections

If the DTC is determined to be intermittent, reviewing the Failure Records can be useful in determining when the DTC was last set.

TEST DESCRIPTION
The numbers below refer to the step numbers on the Diagnostic Table:
2. Command both the ON and OFF states. Repeat the commands as necessary.
3. This step determines if the condition is located on the coil side or the switch side of the circuit.
4. This step verifies that the PCM is providing voltage to the fuel pump relay.
5. This step tests for an open in the fuel pump relay ground circuit.
6. This step determines if a voltage is constantly being applied to the fuel pump relay.
12. This tests for a grounded circuit between the in-line connector and the fuel pump fuse.
15. This step jumps the fuel pump relay in order to activate the fuel pump.
16. This step tests for an open in the fuel pump feed circuit between the in-line connector and the fuel pump relay.
17. This step tests for an open or high resistance in the fuel pump ground circuit.
20. This step determines if the condition with the circuit is intermittent. If the fuse does not open, inspect the supply voltage circuit between the
fuse and the fuel pump for an intermittent condition.

Fuel System Diagnosis


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 593
Chevrolet Venture V6-3.4L VIN E 2273

Diagnostic Chart

SYSTEM DESCRIPTION
The fuel pump fuse provides system voltage to the fuel pump relay. The PCM grounds the Fuel Pump Relay control circuit to energize the fuel
pump relay. When the ignition is turned ON, the PCM commands the fuel pump relay ON for at least 2 seconds, voltage is applied to the electric
fuel pump and will continue to energizes the fuel pump after the PCM receives 3X reference pulses. The fuel pump is an electric pump and is
part of the Modular Fuel Sender Assembly. The fuel pump supplies fuel through an in-line fuel filter, fuel rail assembly to the fuel injectors. A
fuel pressure regulator, attached to the fuel rail assembly, maintains a regulated fuel pressure for correct operation of the fuel injectors. Any
unused fuel is then returned to the fuel tank by a separate fuel return pipe.

Fuel System Pressure Test


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 594
Chevrolet Venture V6-3.4L VIN E 2274
Diagnostic Chart (Part 1 Of 3)

Diagnostic Chart (Part 2 Of 3)


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 595
Chevrolet Venture V6-3.4L VIN E 2275

Diagnostic Chart (Part 3 Of 3)

SYSTEM DESCRIPTION
Proper fuel pressure is necessary to maintain efficient engine operation and emission levels, if fuel pressure is not within specifications vehicle
drivability may be affected or emission levels elevated.

The fuel system contains the following components:


- Fuel strainer
- Modular fuel sender assembly
- Fuel filter
- Fuel feed pipes/hoses
- Fuel pressure regulator
- Fuel rail
- Fuel injectors
- Fuel return pipes/hoses

TEST DESCRIPTION
Numbers below refer to the step numbers on the Diagnostic Table.
2. Tests the fuel systems ability to achieve a specific fuel pressure range. It may be necessary to cycle the fuel pump several times to achieve the
pressure range.
6. A fuel system that drops more than 5 psi in 10 minutes has a leak in one or more areas.
8. Tests the fuel systems ability to maintain a specific fuel pressure. It may be necessary to cycle the fuel pump several times to achieve the
pressure range.
9. Fuel pressure that drops-off during acceleration, cruise, or hard cornering may cause a lean condition. A lean condition can cause a loss of
power, surging, or misfire and may be diagnosed using a scan tool. If an extremely lean condition occurs, the oxygen sensors may drop
below 500 mV and the fuel injector pulse width will increase.
13. When the engine is at idle, the manifold pressure is low (high vacuum). This low pressure (high vacuum) is applied to the fuel pressure
regulator diaphragm, the result is lower fuel pressure. The fuel pressure at idle will vary slightly as the pressure changes, but the fuel pressure
at idle should always be less than the fuel pressure noted in Step 2 with the engine OFF.
14. This test determines if the high fuel pressure is due to a restricted fuel return pipe or fuel pressure regulator. A rich condition may cause a
DTC P0132 or DTC P0172 to set. Driveability conditions associated with rich conditions can include hard starting (followed by black
smoke) and a strong sulfur smell in the exhaust.

Fuel Tank Leak Check


IMPORTANT: Before attempting the Fuel Tank Leak Check place a dry chemical (Class B) fire extinguisher near the work area.
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 596
Chevrolet Venture V6-3.4L VIN E 2276
1. Install the J 41415-40 Fill Tank Cap Adaptor.
2. Connect the J 41413 EVAP Pressure/Purge Diagnostic Station to the fill tank cap adaptor.
3. With a scan tool, seal the EVAP system.
4. Raise the vehicle on a hoist. Refer to Vehicle Lifting Caution in Service Precautions.
5. With the Evaporative Emission System (EVAP) diagnostic station, maintain 15 in. H2O (3.75 kPa) within the fuel tank.

IMPORTANT: It may be necessary to partially lower the fuel tank to inspect the top of the fuel tank and fuel sender assembly O-ring. Refer to
Fuel Tank Replacement.

6. With the J 41416 ultrasonic leak detector, test for leaks in the fuel tank and EVAP pipes.
7. Visually inspect for fuel leaking from the fuel tank.
8. If a leak is detected refer to the following component replacements:
- Fuel tank leak, refer to Fuel Tank Replacement.
- Fuel sender O-ring or fuel sender leak, refer to Fuel Sender Assembly Replacement.
- Fuel or EVAP pipe leak, refer to Fuel Hose/Pipes Replacement (Filter to Tank) in Fuel Supply Line or Fuel Return Line.

Idle Air Control System Diagnosis


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 597
Chevrolet Venture V6-3.4L VIN E 2277

Diagnostic Chart (Part 1 Of 2)


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 598
Chevrolet Venture V6-3.4L VIN E 2278

Diagnostic Chart (Part 2 Of 2)

Schematic

CIRCUIT DESCRIPTION
The Powertrain Control Module (PCM) controls the engine idle speed by adjusting the position of the Idle Air Control (IAC) motor pintle. The
IAC is a bi-directional motor driven by 2 coils. The PCM pulses current to the IAC coils in steps (counts) in order to extend the IAC pintle into a
passage in the throttle body and decrease air flow. The PCM reverses the current pulses in order to retract the pintle and increase air flow. This
method allows highly accurate control of the idle speed and quick response to changes in engine load.

DIAGNOSTIC AIDS
Inspect for the following conditions:
- Inspect the wiring harness for damage.
- A restricted air intake system. Inspect for a collapsed air intake duct, a restricted air filter element, or foreign objects blocking the air intake
system.
- The throttle body. Inspect for objects blocking the IAC passage or the throttle bore, excessive deposits in the IAC passage and on the IAC
pintle, and excessive deposits in the throttle bore and on the throttle plate.
Inspect for a sticking throttle plate. Also inspect the IAC passage for deposits or objects which do not allow the IAC pintle to fully extend.
- A vacuum leak - Inspect for conditions that cause vacuum leaks, such as:
- Disconnected or damaged hoses
- Leaks at the EGR valve and at the EGR pipe to the intake manifold
- Leaks at the throttle body
- A faulty or incorrectly installed PCV valve
- Leaks at intake manifold
- The brake booster hose disconnected, etc.

IMPORTANT: Remove any debris from the connector surfaces before servicing a component. Inspect the connector gaskets when diagnosing
or replacing a component. Ensure that the gaskets are installed correctly. The gaskets prevent contaminate intrusion.
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 599
Chevrolet Venture V6-3.4L VIN E 2279

- Poor terminal connection-Inspect the harness connectors for backed out terminals, improper mating, broken locks, improperly formed or
damaged terminals, and faulty terminal to wire connection. Use a corresponding mating terminal to test for proper tension. Refer to
Diagrams.
- Damaged harness-Inspect the wiring harness for damage. If the harness inspection does not reveal a problem, observe the display on the scan
tool while moving connectors and wiring harnesses related to the sensor. A change in the scan tool display may indicate the location of the
fault. Refer to Diagrams.
- PCM and engine grounds for clean and secure connections

If the DTC is determined to be intermittent, reviewing the Failure Records can be useful in determining when the DTC was last set.

TEST DESCRIPTION
The numbers below refers to the step number on the Diagnostic Table:
11. This vehicle is equipped with a PCM which utilizes an Electrically Erasable Programmable Read-only Memory (EEPROM). When the PCM
is replaced, the new PCM must be programmed.

MAP Sensor Circuit Diagnosis

Diagnostic Chart (Part 1 Of 2)


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 600
Chevrolet Venture V6-3.4L VIN E 2280

Diagnostic Chart (Part 2 Of 2)


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 601
Chevrolet Venture V6-3.4L VIN E 2281

Schematic

CIRCUIT DESCRIPTION
The Manifold Absolute Pressure (MAP) sensor responds to changes in intake manifold pressure (vacuum). The MAP sensor signal voltage to the
PCM varies from below 2.0 volts at idle (high vacuum) to above 4 volts with the key ON, engine not running or at wide-open throttle (low
vacuum). The MAP sensor is used to determine manifold pressure changes while the EGR flow test diagnostic is being run, refer to DTC P0401
Exhaust Gas Recirculation (EGR) Flow Insufficient. Also to update the barometric pressure reading (BARO), and as a enabling factor for other
diagnostics. The PCM monitors the MAP signals for voltages outside the normal range of the MAP sensor. If the PCM detects a MAP signal
voltage that is excessively high, refer to DTC P0108 Manifold Absolute Pressure (MAP) Sensor Circuit High Voltage will be set. See:
Diagnostic Trouble Code Tests and Associated Procedures/P Code Charts/P0108

If the PCM detects a MAP signal voltage that is excessively low, refer to DTC P0107 Manifold Absolute Pressure (MAP) Sensor Circuit Low
Voltage will be set. See: Diagnostic Trouble Code Tests and Associated Procedures/P Code Charts/P0107

DIAGNOSTIC AIDS
Inspect for the following conditions:
- Monitor the MAP sensor using a scan tool. If the MAP sensor does not respond to throttle changes, inspect the 3X reference circuits from the
ignition control module to the PCM.
If the 3X reference signal is lost the PCM will only update the MAP sensor reading once per key cycle, when the engine is first started.
Depending on where the MAP sensor voltage (high voltage or low voltage) is when the engine is started, the high or low voltage MAP sensor
DTCs will set.
- Inspect for kinked and damaged vacuum hoses, ensure that a good vacuum source is available. Refer to Emission Hose Routing Diagram.

IMPORTANT: Remove any debris from the connector surfaces before servicing a component. Inspect the connector gaskets when diagnosing
or replacing a component. Ensure that the gaskets are installed correctly. The gaskets prevent contaminate intrusion.

- Poor terminal connection-Inspect the harness connectors for backed out terminals, improper mating, broken locks, improperly formed or
damaged terminals, and faulty terminal to wire connection. Use a corresponding mating terminal to test for proper tension. Refer to
Diagrams.
- Damaged harness-Inspect the wiring harness for damage. If the harness inspection does not reveal a problem, observe the display on the scan
tool while moving connectors and wiring harnesses related to the sensor. A change in the scan tool display may indicate the location of the
fault. Refer to Diagrams.
- PCM and engine grounds for clean and secure connections
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 602
Chevrolet Venture V6-3.4L VIN E 2282

If the DTC is determined to be intermittent, reviewing the Failure Records can be useful in determining when the DTC was last set.

PCM Controlled A/C Circuit Diagnosis

Diagnostic Chart (Part 1 Of 2)


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 603
Chevrolet Venture V6-3.4L VIN E 2283

Diagnostic Chart (Part 2 Of 2)

Refer to following:
Engine Controls Schematics 5 Volt Reference B Ckt. See: Diagrams/Electrical Diagrams

A/C Compressor Controls. See: Diagrams/Electrical Diagrams

Compressor Schematic in HVAC - Manual. See: Heating and Air Conditioning/Diagrams/Electrical Diagrams

CIRCUIT DESCRIPTION
When A/C is selected through the A/C controller a signal is supplied to the PCM through a 12 volt A/C request circuit to the PCM. The PCM
monitors the A/C refrigerant pressure. If the A/C refrigerant pressure, and engine operating conditions are within a specific calibrated acceptable
ranges the PCM will enable the A/C Relay. This is accomplished by providing a ground path for the A/C Relay coil within the PCM. When the
A/C compressor relay is enabled battery positive voltage is supplied to the compressor clutch coil.

The PCM will enable the A/C compressor clutch whenever the engine is running and the A/C has been requested, unless any of the following
conditions are met:
- Throttle more than 96 percent.
- A/C pressure sensor more than 440 psi (4.6 volts) or less than 36 psi (0.35 volt) (as determined by the A/C pressure sensor)
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 604
Chevrolet Venture V6-3.4L VIN E 2284
- Ignition voltage below 10.0 volts
- Engine speed more than 4700 RPM
- ECT more than 124°C (2557°F)
- IAT less than 5°C (41°F)
- An open or a short to ground in the 12 Volt A/C request circuit

DIAGNOSTIC AIDS
Inspect for the following:

IMPORTANT: Remove any debris from the connector surfaces before servicing a component. Inspect the connector gaskets when diagnosing
or replacing a component. Ensure that the gaskets are installed correctly. The gaskets prevent contaminate intrusion.

- Poor terminal connection-Inspect the harness connectors for backed out terminals, improper mating, broken locks, improperly formed or
damaged terminals, and faulty terminal to wire connection. Use a corresponding mating terminal to test for proper tension. Refer to
Diagrams.
- Damaged harness-Inspect the wiring harness for damage. If the harness inspection does not reveal a problem, observe the display on the scan
tool while moving connectors and wiring harnesses related to the sensor. A change in the scan tool display may indicate the location of the
fault. Refer to Diagrams.
- PCM and engine grounds for clean and secure connections

If the DTC is determined to be intermittent, reviewing the Failure Records can be useful in determining when the DTC was last set.

Restricted Exhaust System Check (Part 1 Of 2)


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 605
Chevrolet Venture V6-3.4L VIN E 2285

Restricted Exhaust System Check 1 Of 2

Crank Relay Functional Test


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 606
Chevrolet Venture V6-3.4L VIN E 2286

Diagnostic Chart (Part 1 Of 2)


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 607
Chevrolet Venture V6-3.4L VIN E 2287

Diagnostic Chart (Part 2 Of 2)

Refer to Engine Controls Schematic Power, Ground, MIL, DLC, Transaxle Range Sw. See: Diagrams/Electrical Diagrams

Refer to Starting and Charging, Starter Schematics in Starting and Charging. See: Starting and Charging

CIRCUIT DESCRIPTION
The Ignition Switch provides ignition positive voltage to the PCM while in the Crank position. When the PCM receives the Crank signal, it then
determines if the Theft Deterrent Fuel Enable Signal is correct and received in time. If the signal is accepted then the PCM provides a ground
path for the Crank Relay Control Circuit, which closes the Crank Relay contacts and provides battery positive voltage to the Starter Solenoid.

The PCM has the ability to disable the Crank Relay if a short to ignition or battery positive voltage is evident on the Crank Signal circuit, or if
the Ignition Switch is left in the crank position for an extended period of time (approximately 5-8 seconds) with the engine running. The Crank
Relay will also be disabled if the engine is running, a correct theft deterrent password is not received or if the vehicle is started while not in
Park/Neutral position.
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 608
Chevrolet Venture V6-3.4L VIN E 2288

The PCM controlled starter system consists of the following components:


- The Ignition Switch
- The Crank Signal
- The PCM
- The Crank Relay Control Circuit
- The Transaxle Range/Park Neutral Position Switch
- The Crank Relay
- The Starter Solenoid
- The Starter Motor

DIAGNOSTIC AIDS
The Crank Relay Functional test is intended to identify electrical malfunctions that can occur with the PCM Control Starter System. For
additional system diagnosis, refer to A Diagnostic System Check - Starting and Charging in Starting and Charging.

Inspect for the following conditions:

IMPORTANT: Remove any debris from the connector surfaces before servicing a component. Inspect the connector gaskets when diagnosing
or replacing a component. Ensure that the gaskets are installed correctly. The gaskets prevent contaminate intrusion.

- Poor terminal connection-Inspect the harness connectors for backed out terminals, improper mating, broken locks, improperly formed or
damaged terminals, and faulty terminal to wire connection. Use a corresponding mating terminal to test for proper tension. Refer to
Diagrams.
- Damaged harness-Inspect the wiring harness for damage. If the harness inspection does not reveal a problem, observe the display on the scan
tool while moving connectors and wiring harnesses related to the sensor. A change in the scan tool display may indicate the location of the
fault. Refer to Diagrams.
- PCM and engine grounds for clean and secure connections

If the DTC is determined to be intermittent, reviewing the Failure Records can be useful in determining when the DTC was last set.

TEST DESCRIPTION
Numbers below refer to step numbers in the diagnostic table:

IMPORTANT: The Starter is capable of engaging with the ignition OFF, or while in gear.

3. This test determines if the Starter is cranking with the ignition OFF.
4. If the Crank Signal circuit is shorted to battery or ignition positive voltage and the ignition is on the Crank Relay will be commanded ON at
ignition power up, and will be disabled after the engine is running.

Starter Cranks With Ignition Off

Diagnostic Chart (Part 1 Of 2)


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 609
Chevrolet Venture V6-3.4L VIN E 2289

Diagnostic Chart 2 Of 2

Refer to Engine Controls Schematic Power, Ground, MIL, DLC, Transaxle Range Sw. See: Diagrams

Refer to Starting and Charging, Starter Schematics in Starting and Charging.

CIRCUIT DESCRIPTION
The Crank Relay Functional Test should be the starting point to determine which diagnosis to perform based on the symptom of the starting
system. This diagnosis determines if the Crank Relay or the starter solenoid feed circuit is operating properly.

DIAGNOSTIC AIDS
For additional system diagnosis, refer to A Diagnostic System Check Starting and Charging. See: Starting and Charging/Testing and Inspection

Inspect for the following conditions:

IMPORTANT: Remove any debris from the connector surfaces before servicing a component. Inspect the connector gaskets when diagnosing
or replacing a component. Ensure that the gaskets are installed correctly. The gaskets prevent contaminate intrusion.

- Poor terminal connection-Inspect the harness connectors for backed out terminals, improper mating, broken locks, improperly formed or
damaged terminals, and faulty terminal to wire connection. Use a corresponding mating terminal to test for proper tension. Refer to
Diagrams.
- Damaged harness-Inspect the wiring harness for damage. If the harness inspection does not reveal a problem, observe the display on the scan
tool while moving connectors and wiring harnesses related to the sensor. A change in the scan tool display may indicate the location of the
fault. Refer to Diagrams.
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 610
Chevrolet Venture V6-3.4L VIN E 2290
- PCM and engine grounds for clean and secure connections

If the DTC is determined to be intermittent, reviewing the Failure Records can be useful in determining when the DTC was last set.

TEST DESCRIPTION
Numbers below refer to step numbers in the diagnostic table:

IMPORTANT: The Starter is capable of engaging with the ignition OFF, or while in gear.

3. This test determines if the Starter is cranking with the Crank Relay disconnected, and the ignition OFF.

Starter Cranks With Ignition On

Diagnostic Chart (Part 1 Of 2)


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 611
Chevrolet Venture V6-3.4L VIN E 2291

Diagnostic Chart (Part 2 Of 2)

Refer to Engine Controls Schematic Power, Ground, MIL, DLC, Transaxle Range Sw. See: Diagrams/Electrical Diagrams

Refer to Starting and Charging, Starter Schematics in Starting and Charging. See: Starting and Charging

CIRCUIT DESCRIPTION
The Crank Relay Functional Test should be the starting point to determine which diagnosis to perform based on the symptom of the starting
system. This diagnosis determines if the Crank Signal circuit is operating properly

DIAGNOSTIC AIDS
For additional system diagnosis, refer to A Diagnostic System Check Starting and Charging. See: Starting and Charging

Inspect for the following conditions:

IMPORTANT: Remove any debris from the connector surfaces before servicing a component. Inspect the connector gaskets when diagnosing
or replacing a component. Ensure that the gaskets are installed correctly. The gaskets prevent contaminate intrusion.

- Poor terminal connection-Inspect the harness connectors for backed out terminals, improper mating, broken locks, improperly formed or
damaged terminals, and faulty terminal to wire connection. Use a corresponding mating terminal to test for proper tension. Refer to
Diagrams.
- Damaged harness-Inspect the wiring harness for damage. If the harness inspection does not reveal a problem, observe the display on the scan
tool while moving connectors and wiring harnesses related to the sensor. A change in the scan tool display may indicate the location of the
fault. Refer to Diagrams.
- PCM and engine grounds for clean and secure connections
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 612
Chevrolet Venture V6-3.4L VIN E 2292

If the DTC is determined to be intermittent, reviewing the Failure Records can be useful in determining when the DTC was last set.

TEST DESCRIPTION
Numbers below refer to step numbers in the diagnostic table:
2. This test assumes the ignition switch is operating properly.

Starter Cranks With Engine Running

Diagnostic Chart (Part 1 Of 3)


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 613
Chevrolet Venture V6-3.4L VIN E 2293

Diagnostic Chart (Part 2 Of 3)


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 614
Chevrolet Venture V6-3.4L VIN E 2294

Diagnostic Chart (Part 3 Of 3)

Refer to Engine Controls Schematic Power, Ground, MIL, DLC, Transaxle Range Sw. See: Diagrams/Electrical Diagrams

Refer to Starting and Charging, Starter Schematics in Starting and Charging. See: Starting and Charging

CIRCUIT DESCRIPTION
The Crank Relay Functional Test should be the starting point to determine which diagnosis to perform based on the symptom of the starting
system. This diagnosis determines it the Crank Relay Control circuit or the Starter Solenoid feed circuit is operating properly.

DIAGNOSTIC AIDS
For additional system diagnosis, refer to A Diagnostic System Check Starting and Charging. See: Starting and Charging

Inspect for the following conditions:

IMPORTANT: Remove any debris from the connector surfaces before servicing a component. Inspect the connector gaskets when diagnosing
or replacing a component. Ensure that the gaskets are installed correctly. The gaskets prevent contaminate intrusion.

- Poor terminal connection-Inspect the harness connectors for backed out terminals, improper mating, broken locks, improperly formed or
damaged terminals, and faulty terminal to wire connection. Use a corresponding mating terminal to test for proper tension. Refer to
Diagrams.
- Damaged harness-Inspect the wiring harness for damage. If the harness inspection does not reveal a problem, observe the display on the scan
tool while moving connectors and wiring harnesses related to the sensor. A change in the scan tool display may indicate the location of the
fault. Refer to Diagrams.
- PCM and engine grounds for clean and secure connections
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 615
Chevrolet Venture V6-3.4L VIN E 2295

If the DTC is determined to be intermittent, reviewing the Failure Records can be useful in determining when the DTC was last set.

Starter Does Not Crank

Diagnostic Chart (Part 1 Of 7)


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 616
Chevrolet Venture V6-3.4L VIN E 2296

Diagnostic Chart (Part 2 Of 7)


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 617
Chevrolet Venture V6-3.4L VIN E 2297

Diagnostic Chart (Part 3 Of 7)


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 618
Chevrolet Venture V6-3.4L VIN E 2298

Diagnostic Chart (Part 4 Of 7)


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 619
Chevrolet Venture V6-3.4L VIN E 2299

Diagnostic Chart (Part 5 Of 7)


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 620
Chevrolet Venture V6-3.4L VIN E 2300

Diagnostic Chart (Part 6 Of 7)


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 621
Chevrolet Venture V6-3.4L VIN E 2301

Diagnostic Chart (Part 7 Of 7)

Refer to Engine Controls Schematic Power, Ground, MIL, DLC, Transaxle Range Sw. See: Diagrams/Electrical Diagrams

Refer to Starting and Charging, Starter Schematics in Starting and Charging. See: Starting and Charging

CIRCUIT DESCRIPTION
The Crank Relay Functional Test should be the starting point to determine which diagnosis to perform based on the symptom of the starting
system. This diagnosis determines if the Crank Signal circuit, Crank Relay, Crank Relay feed circuit, or the Starter Solenoid feed circuit is
operating properly.

DIAGNOSTIC AIDS
For additional system diagnosis, refer to A Diagnostic System Check Starting and Charging. See: Starting and Charging

Inspect for the following conditions:

IMPORTANT: Remove any debris from the connector surfaces before servicing a component. Inspect the connector gaskets when diagnosing
or replacing a component. Ensure that the gaskets are installed correctly. The gaskets prevent contaminate intrusion.

- Poor terminal connection-Inspect the harness connectors for backed out terminals, improper mating, broken locks, improperly formed or
damaged terminals, and faulty terminal to wire connection. Use a corresponding mating terminal to test for proper tension. Refer to
Diagrams.
- Damaged harness-Inspect the wiring harness for damage. If the harness inspection does not reveal a problem, observe the display on the scan
tool while moving connectors and wiring harnesses related to the sensor. A change in the scan tool display may indicate the location of the
fault. Refer to Diagrams.
- PCM and engine grounds for clean and secure connections
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 622
Chevrolet Venture V6-3.4L VIN E 2302

If the DTC is determined to be intermittent, reviewing the Failure Records can be useful in determining when the DTC was last set.

Scan Tool Data List - Powertrain System

Scan Tool Data List (Part 1 Of 4)


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 623
Chevrolet Venture V6-3.4L VIN E 2303

Scan Tool Data List (Part 2 Of 4)


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 624
Chevrolet Venture V6-3.4L VIN E 2304

Scan Tool Data List (Part 3 Of 4)


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 625
Chevrolet Venture V6-3.4L VIN E 2305

Scan Tool Data List (Part 4 Of 4)

The Engine Scan Tool Data List contains all of the engine related parameters that are available on the scan tool. The list is arranged in alphabetical
order. A given parameter may appear in any one of the data lists, and, in some cases, may appear more than once or in more than one data list in
order to group certain related parameters together.

Use the Engine Scan Tool Data List only after the following are determined:
- The Powertrain On-Board Diagnostic System Check is completed.
- No Diagnostic Trouble Codes (DTCs) are present.
- The on-board diagnostics are functioning properly.

Scan tool values from a properly running engine may be used for comparison with the engine you are diagnosing. The Engine Scan Tool Data List
represents values that would be seen from a normally running engine.

IMPORTANT: A scan tool that displays faulty data should not be used. Any scan tool concern should be reported to the manufacturer. Use of a
faulty scan tool can result in misdiagnosis and unnecessary parts replacement.

Only the parameters listed below are referenced for use in diagnosis. If all values are within the typical range described below, refer to Symptoms
for diagnosis.

The column labeled Data List indicates where a parameter can be located on the scan tool. Refer to the scan tool operating manual for the exact
locations of the data lists. The following is a description of each term listed:

Engine Data1: The engine data 1 list


Catalyst Data: The exhaust catalyst data
EGR Data: The exhaust recirculation valve data
EVAP Data: The evaporative emissions data
IPC Data: The instrument panel cluster data
HO2S Data: The heated oxygen sensor data
Misfire Data: The cylinder misfire data
AIR Data: The air injection reaction data
ODD Data: The output driver data

A/C Relay
Scan Tool Displays OK, Fault or Invalid State. These parameters describe the condition of the control circuit.
A/C Request
Scan Tool Displays YES or NO. Indicates the state of the A/C request input circuit from the HVAC controls. The PCM uses the A/C request signal
to determine whether A/C compressor operation is being requested.
AIR Solenoid
Scan Tool Displays OK/Fault/Invalid State in ODD and AIR. Scan Tool Displays On/Off in Eng1 ,HO2S,AIR. These parameters describe the
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 626
Chevrolet Venture V6-3.4L VIN E 2306
condition of the control circuit.
Abuse Management
Scan Tool Displays Active or Inactive. Active indicates the PCM is commanding protection against abnormal driveline conditions. For further
information refer to Automatic Transaxle Diagnosis.
Actual EGR Position
Scan Tool Displays 0-100 percent. Represents the actual position of the EGR pintle in percent. 0 percent displayed indicates a fully extended
pintle (EGR valve closed).
Air Active Test Air Injection
Scan Tool Displays Yes or No in AIR. The AIR Active Test has the PCM turn on the Air Pump specifically for diagnostic purposes.
Air Active Test Inhibit
Scan Tool Displays Yes or No in AIR.
Air Diagnostic Complete
Scan Tool Displays Yes or No in AIR. When all the passive and active tests have been completed.
Air Passive Test In Progress
Scan Tool Displays Yes or No in AIR. Displays the AIR Passive Tests are in progress.
Air Passive Test Inhibit
Scan Tool Displays Yes or No in AIR.
Air Passive Test Passed
Scan Tool Displays Yes or No in AIR. Indicates that both AIR Passive Test 1 and 2 have passed and no further action is needed.
Air Passive Test 1 Passed
Scan Tool Displays Yes or No in AIR. AIR Passive Test 1 is being performed during regular AIR Pump operation. When Test 1 is passed, the
diagnostic will proceed to AIR Passive Test 2.
Air Passive Test 2 Fail
Scan Tool Displays Yes or No in AIR. If either AIR Passive Test 1 or 2 fails or is inconclusive, the diagnostic will proceed to the AIR Active Test.
Air Pump Relay
Scan Tool Displays OK/Fault/Invalid State in ODD. Scan Tool Displays On/Off in Eng1,AIR,HO2S. These parameters describe the condition of
the control circuit.
Air/fuel Ratio
Scan Tool Displays 0.0-25.5. Air/Fuel Ratio indicates the PCM commanded value. In closed loop, Air/Fuel Ratio should normally be around
14.2-14.7. A lower Air/Fuel Ratio indicates a richer commanded mixture, which may be seen during Power Enrichment or TWC Protection modes.
A higher Air/Fuel Ratio indicates a leaner commanded mixture. This can be seen during Decel Fuel Mode.
Brake Switch
Scan Tool Displays APPLIED or RELEASED. Indicates the brake pedal position. When the brake pedal is depressed a signal voltage is sent to the
PCM.
Cam Signal Present
Scan Tool Displays YES or NO. If the PCM does not receive a cam signal from the Ignition Control Module the scan tool displays NO.
Commanded A/C
Scan Tool Displays ON or OFF. Represents the PCM commanded state of the A/C compressor clutch relay driver circuit. The A/C compressor
clutch should be engaged when Commanded A/C displays ON.
Commanded Fuel Pump
Scan Tool Displays ON or OFF. Indicates the PCM commanded state of the fuel pump relay control circuit.
Commanded Gen
Scan Tool Displays ON or OFF. OFF displayed indicates that the PCM has commanded the generator control circuit OFF.
Cruise Inhibited
Scan Tool Displays On or Off in Eng1.. Scan Tool Displays OK/Fault/Invalid State in ODD. On or OK displayed indicates that the PCM is
commanding the Cruise Control Module to inhibit cruise control operation. Should display ON or OK at idle.
Cruise Mode
Scan Tool Displays ON or OFF. Represents the state of the Cruise Status Input from the Cruise Control Module. Cruise Engaged should not display
Yes unless the vehicle is operating in a cruise control mode.
Cyl 1-6 CKT Status
Scan Tool Displays OK, Stuck Low (open) or Stuck High. These parameters describe the condition of each injector control circuit.
Cyl 1-6 CKT History
Scan Tool Displays OK, Stuck Low (open) or Stuck High. These parameters describe the condition of each injector control circuit. If a fault is
detected the scan tool will list which the fault type with the corresponding cylinder.
Decel Fuel Mode
Scan Tool Displays ACTIVE or INACTIVE. ACTIVE is displayed if the PCM has detected conditions appropriate to operate in Deceleration Fuel
Mode. The PCM will command deceleration fuel mode when a sudden decrease in throttle position has been detected while the vehicle is traveling
over 40 km/h (25 mph). While in Deceleration Fuel mode, the PCM will decrease the amount of fuel delivered by entering Open Loop and
decreasing the injector pulse width.
ECT
Scan Tool Displays -40°C to 151°C (-40°F to 304°F). The Engine Coolant Temperature (ECT) sensor is mounted in the coolant stream. The PCM
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 627
Chevrolet Venture V6-3.4L VIN E 2307
applies 5 volts to the ECT sensor circuit. The sensor is a thermistor which changes internal resistance as temperature changes. When the sensor is
cold (internal resistance high), the PCM monitors a high signal voltage and interprets the data as a cold engine. As the sensor warms (internal
resistance decreases), the voltage signal decreases and the PCM interprets the lower voltage as a warm engine.
EGR Closed Valve Pintle Position
Scan Tool Displays 0.0-5.0 volts. Represents the learned voltage that the PCM uses to determine whether or not the EGR valve is fully closed (0
percent pintle position). If the Desired EGR Position is 0 percent and a difference of more than 0.4 volt between EGR Feedback and EGR Closed
Valve Pintle Position is detected, DTC P1406 will set.
EGR Duty Cycle
Scan Tool Displays 0-100 percent. Represents the EGR valve driver PWM signal from the PCM. A duty cycle of 0 percent indicates that no EGR
flow is being commanded. A 100 percent duty cycle indicates maximum EGR flow commanded.
EGR Feedback
Scan Tool Displays 0.00-5.00 Volts. Indicates the EGR pintle position sensor signal voltage being monitored by the PCM. A low voltage indicates
a fully extended pintle (closed valve). A voltage near 5 volts indicates a fully retracted pintle (open valve).
EGR Flow Test Count
Scan Tool Displays 0-255 counts. Indicates the number of EGR flow test samples collected during the current ignition cycle. The maximum
number of samples allowed is 1 during normal operation. If the PCM battery feed has been disconnected or a DTC P0401 has been cleared, several
EGR flow test samples will be allowed during the next ignition cycle. This is to allow repair verification during a single ignition cycle.
EGR Position Error
Scan Tool Displays 0-100 percent. Indicates the difference between Desired EGR Position and Actual EGR Position currently being monitored by
the PCM. If the EGR Position Error reaches an unacceptable level, a DTC will set.
Engine LOAD
Scan Tool Displays 0-100 percent. Engine load is calculated by the PCM from engine speed and MAF sensor readings. Engine Load should
increase with an increase in RPM or air flow.
Engine Oil Level
Scan Tool Displays OK or Low IN IPC. Indicates the oil level as determined by the Engine Oil Level Sensor.
Engine Oil Life
Scan Tool Displays Percents in IPC. Indicates how much oil life is left until the next recommended oil change.
Engine Oil Pressure
Scan Tool Displays Ok/Low/High in IPC. Indicates the oil pressure as determined by the Oil Sending Unit.
EVAP Canister Purge
Scan Tool Displays 0-100 percent. Represents the PCM commanded PWM duty cycle of the EVAP Purge valve. 0 percent displayed indicates no
purge. A 100 percent displayed indicates full purge.
EVAP Fault History
Scan Tool Displays NO FAULT, EXCESS VACUUM, PURGE VALVE LEAK, SMALL LEAK or WEAK VACUUM. The EVAP Fault History
indicates the status of the EVAP system diagnostics performed by the PCM.
EVAP Purge Solenoid
Scan Tool Displays OK, Fault or Invalid State. These parameters describe the condition of the control circuit.
EVAP Vent Solenoid
Scan Tool Displays Open or Closed in Eng1 and HO2S. Scan Tool Displays OK/Fault/Invalid State in EVAP. The scan tool displays Open and Ok
when the PCM commands the EVAP system to purge. The scan tool will show Closed when the system is not purging.
Fan Control Relay 1
Scan Tool Displays OK, Fault or Invalid State. These parameters describe the condition of the control circuit.
Fan Control Relay 2 and 3
Scan Tool Displays OK, Fault or Invalid State. These parameters describe the condition of the control circuit.
Fans High Speed
Scan Tool Displays ON or OFF. Represents the PCM commanded state of both fans.
Fans Low Speed
Scan Tool Displays ON or OFF. Represents the PCM commanded state of both fans.
Fuel Tank Pressure
Scan Tool Displays in 0-5.00 volts or -32 to 32 (in/H2O). This parameter indicates the pressure/Vacuum inside of the fuel tank. A negative value
indicates a vacuum. A positive value indicates a pressure.
Fuel Trim Learn
Scan Tool Displays Enabled or Disabled. When conditions are appropriate for enabling long term fuel trim corrections, FUEL TRIM LEARN will
display Enable. This indicates that the long term fuel trim is responding to short term fuel trim. If the Fuel Trim Learn displays Disable, long term
fuel trim will not respond to changes in short term fuel trim.
Generator PWM
Scan Tool Displays In Percents In IPC.

Hot Mode
Scan Tool Displays ON or OFF. On displayed indicates that the PCM has detected conditions appropriate for Transaxle hot mode operation. The
PCM determines this base on Transaxle fluid temperature. While in Hot Mode, Transaxle shift points may be altered, 4th gear disabled, and the
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 628
Chevrolet Venture V6-3.4L VIN E 2308
TCC forced On in 2nd gear.
Hot Open Loop
Scan Tool Displays Active or Inactive in IPC.
HO2S Sensor 1
Scan Tool Displays READY or NOT READY. Indicates the status of the fuel control exhaust oxygen sensor. The scan tool will indicate that the
exhaust oxygen sensors are ready when the PCM detects a fluctuating HO2S voltage sufficient to allow closed loop operation. This will not occur
unless the exhaust oxygen sensors are warmed up.

Scan Tool Displays 0-1132 mV. Represents the fuel control exhaust oxygen sensor output voltage. Should fluctuate constantly within a range
between 10 mV (lean exhaust) and 1000 mV (rich exhaust) while operating in Closed Loop.
HO2S Sensor 2
Scan Tool Displays 0-1132 mV. Represents the fuel control exhaust oxygen sensor output voltage. Should fluctuate constantly within a range
between 10 mV (lean exhaust) and 1000 mV (rich exhaust) while operating in Closed Loop.
HO2S Xcounts
Scan Tool Displays 0-255. Indicates the number of times the HO2S 1 signal has crossed the 450 mV bias voltage during a 1 second interval. A
HO2S 1 signal that almost never crosses the bias voltage could indicate a fuel trim problem, a faulty HO2S 1 circuit, or a faulty HO2S 1.
IAT
Scan Tool Displays -40°C to 151°C (-40°F to 304°F). The PCM converts the resistance of the intake air temperature sensor to degrees. The PCM
uses Intake Air Temperature (IAT) to adjust fuel delivery and spark timing according to incoming air density. IAT is also compared to ECT at
start-up to identify cold starts for the HO2S heater and the EVAP diagnostics.
Ignition Mode
Scan Tool Displays BYPASS or IC. Indicates the commanded state of the Bypass signal output from the PCM. When BYPASS is displayed, the
ignition control module is controlling the spark advance at a fixed 10 degrees BTDC (Bypass mode). IC displayed indicates that the PCM has
requested control of the spark advance (IC mode). The ignition control module determines the correct operating mode based on the level of voltage
that the PCM applies to the ignition control module bypass circuit. The PCM provides 5 volts to the ignition control module bypass circuit when
conditions are appropriate for PCM control of spark timing (IC mode). If the PCM does not apply 5 volts to the bypass circuit, or if the ignition
control module does not receive the signal, the module will control spark timing.
Ignition 1
Scan Tool Displays 0-25.5 volts. Represents the system voltage measured by the PCM at its ignition feed.
Injector Pulse Width
Scan Tool Displays 0-1000 msec. Indicates the amount of time the PCM is commanding each injector ON during each engine cycle. A longer
injector pulse width will cause more fuel to be delivered. Injector Pulse Width should increase with increased engine load.
Long Term Fuel Trim
Scan Tool Displays -10 to 10 percent. Long Term Fuel Trim is derived from the Short Term Fuel Trim value and represents a long-term correction
of fuel delivery. A value of 0 percent indicates that fuel delivery requires no compensation to maintain the PCM commanded air/fuel ratio. A
negative value significantly below 0 percent indicates that the fuel system is rich and fuel delivery is being reduced (decreased injector pulse
width). A positive value significantly greater than 0 percent indicates that a lean condition exists and the PCM is compensating by adding fuel
(increased injector pulse width). Because Long Term Fuel Trim tends to follow Short Term Fuel Trim, a value in the negative range due to canister
purge at idle should not be considered unusual. The PCM's maximum authority to control long term fuel trim allows a range between -10 percent
and +10 percent. Fuel trim values at or near maximum authority may indicate an excessively rich or lean system.
MAF
Scan Tool Displays 0.0-512 g/s. Mass Air Flow (MAF) is the MAF Input Frequency converted to grams of air per second. This indicates the
amount of air entering the engine.
MAF Frequency
Scan Tool Displays 0-32000 Hz. The MAF sensor input signal to the PCM is a frequency which varies from around 3000 Hz at idle to above 7000
Hz at wide-open throttle. The PCM converts this frequency signal to grams per second to be displayed on the scan tool as MAF.
MAP
Scan Tool Displays 10-105 kPa (0.00-4.97 volts). The Manifold Absolute Pressure (MAP) sensor measures the change in the intake manifold
pressure from engine load, EGR flow, and speed changes. As intake manifold pressure increases, intake vacuum decreases resulting in a higher
MAP sensor voltage and kPa reading. The MAP sensor signal is used to monitor intake manifold pressure changes during the EGR flow test, to
update the BARO reading, and as an enabling factor for many of the diagnostics.
MIL
Scan Tool Displays ON or OFF in IPC. Indicates the PCM commanded state of the Malfunction Indicator Lamp (MIL).

Scan Tool Displays OK, Fault or Invalid State in ODD. These parameters describe the condition of the control circuit.
Misfire Current Cyl 1-6
Scan Tool Displays 0-198 counts. The Misfire Current counters indicate the number of cylinder firing events detected as possible misfires on each
cylinder during the last 200 crankshaft revolutions. The number that the counters display are twice the actual number of misfire events detected.
The counters may normally display some activity, but the activity should be very low and nearly equal for all the cylinders.
Misfire History Cyl 1-6
Scan Tool Displays 0-65535 counts. The Misfire History counters indicate the total level of misfire that has been detected on each cylinder. The
number that the counters display are twice the actual number of misfire events detected. The Misfire History counters will not update or show any
activity until a misfire DTC (P0300) has become active. The Misfire History counters will be updated every time a 200 crankshaft revolution
misfire test failure is detected.
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 629
Chevrolet Venture V6-3.4L VIN E 2309
Power Enrichment
Scan Tool Displays ACTIVE or INACTIVE. ACTIVE displayed indicates that the PCM has detected conditions appropriate to operate in Power
Enrichment mode. The PCM will command Power Enrichment mode when a large increase in throttle position and load is detected. While in Power
Enrichment, the PCM will increase the amount of fuel delivered by entering Open Loop and increasing the injector pulse width. This is done to
prevent a possible sag or hesitation from occurring during acceleration.
Short Term Fuel Trim
Scan Tool Displays -10 to 10 percent. Short Term Fuel Trim represents a short-term correction to fuel delivery by the PCM in response to the
amount of time the fuel control oxygen sensor voltage spends above or below the 450 mVthreshold. If the oxygen sensor voltage has mainly
remained less than 450 mV, indicating a lean air/fuel mixture, short term fuel trim will increase into the positive range above 0 percent and the
PCM will add fuel. If the oxygen sensor voltage stays mainly above the threshold, short term fuel trim will decrease below 0 percent into the
negative range while the PCM reduces fuel delivery to compensate for the indicated rich condition. Under certain conditions such as extended idle
and high ambient temperatures, canister purge may cause Short Term Fuel Trim to read in the negative range during normal operation. The PCM's
maximum authority to control fuel trim allows a range between -10 percent and +10 percent. Fuel trim values at maximum authority may indicate
an excessively rich or lean system.
Cycles Of Misfire Data
Scan Tool Displays counts from 0-99. The number showing represents the number of misfires.
TCC Engaged
Scan Tool Displays Engaged or Disengaged. Indicates the command state of the transaxle Torque Convertor Clutch (TCC).
TCC Solenoid
Scan Tool Displays OK, Fault or Invalid State. These parameters describe the condition of the control circuit.
Total Misfire Current Count
Scan Tool Displays 0-99 counts. Indicates the total number of cylinder firing events that were detected as being misfires during the last 200
crankshaft revolution sample period.
Total Misfire Failures
Scan Tool Displays 0-65535 counts. Indicates the number of 200 crankshaft revolution sample periods during which the level of misfire was
sufficiently high to report a failure.
Total Misfire Passes
Scan Tool Displays 0-65535 counts. Indicates the number of 200 crankshaft revolution sample periods during which the level of misfire was
sufficiently low to report a pass.
TP Angle
Scan Tool Displays 0-100 percent. TP Angle is computed by the PCM from the TP Sensor voltage. TP Angle should display 0 percent at idle and
100 percentat wide open throttle.
TR Switch P / A / B / C
Scan Tool Displays HIGH or LOW. The TR Switch A / B / C display represents the states of the four inputs from the transaxle range switch. HIGH
displayed indicates a B+ voltage signal being monitored at the PCM, LOW displayed indicates a grounded input signal. The combination of
transaxle range inputs indicates the position of the transaxle manual valve.
Transmission Range
Scan Tool Displays PARK/NEUTRAL, REVERSE, DRIVE 4, DRIVE 3, DRIVE 2, or LOW. Transmission Range represents the decoded status of
the four inputs from the Transaxle Range Switch Assembly. The combination of transaxle range inputs indicates the position of the transaxle
manual valve.
TWC Protection
Scan Tool Displays ACTIVE or INACTIVE. ACTIVE displayed indicates that the PCM has detected conditions appropriate to operate in TWC
Protection mode. This is determined based on Engine Load and Engine Coolant Temperature. While in TWC Protection, the PCM will decrease
Air/Fuel Ratio to a value that depends on mass air flow (higher Mass Airflow = lower Air/Fuel Ratio).
Vehicle Speed
Scan Tool Displays 0-255 km/h (0-155 mph). The vehicle speed sensor signal is converted into mph and km/h for display.
VTD Fuel Disable
Scan Tool Displays ACTIVE or INACTIVE. The Theft Deterrent Fuel Enable circuit is an input from the Vehicle Theft Deterrent Control Module
that signals the PCM to enable the injectors if the proper signal is received. The scan tool will normally display INACTIVE. If the Vehicle Theft
Deterrent system does not send the correct Theft Deterrent Fuel Enable signal to the PCM, the display will switch to ACTIVE and the fuel system
may be disabled. Refer to DTCs P1626, P1630, P1631, or Vehicle Theft Deterrent diagnosis for further information.
Fuel Pump CKT History
Scan Tool Displays OK, Stuck Low (open) or Stuck High. These parameters describe the condition of the fuel pump control circuit.
Fuel Pump CKT Status
Scan Tool Displays OK, Stuck Low (open) or Stuck High. These parameters describe the condition of the fuel pump control circuit. If a fault is
detected the scan tool will list which the fault type.
1-2 Solenoid
Scan Tool Displays OK, Fault or Invalid State. These parameters describe the condition of the control circuit.
2-3 Solenoid
Scan tool Displays OK, Fault or Invalid State. These parameters describe the condition of the control circuit.
3X Crank Sensor
Scan Tool Displays 1600-10,000 RPM. This signal is calculated from the 7X pulses and is fed to the PCM by the Ignition Control Module. This is
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 630
Chevrolet Venture V6-3.4L VIN E 2310
used by the PCM to calculate RPM at engine speeds above 1600 RPM and to initiates injector pulses.
24X Crank Sensor
Scan Tool Displays 0-1600 RPM. Displays the engine speed calculated from the 24x Reference signal PCM input. Should nearly match Engine
Speed up to approximately 1,600 RPM limit.
A/C High Side Pressure
Scan Tool Displays 0.00-5.00 volts. Represents the A/C refrigerant pressure sensor signal. The amount of pressure indicates the amount of load that
the A/C compressor is placing on the engine. The PCM uses this information to adjust idle and to control the cooling fans.
BARO
Scan Tool Displays 10-105 kPa (0.00 to 5.00 volts). The barometric pressure reading is determined from the MAP sensor signal monitored during
key up and Wide-open Throttle (WOT) conditions. Barometric pressure is used to adjust fuel delivery and spark advance to compensate for altitude
changes.
Current Gear
Scan Tool Displays 0-4. The scan tool display the gear that the transmission is in.
Desired EGR Position
Scan Tool Displays 0-100 percent. Represents the EGR pintle position that the PCM is commanding. Desired EGR Position should stay close to
Actual EGR Position.
Desired Idle Speed
Scan Tool Displays 0-3187 RPM. Represents the idle speed that is commanded by the PCM. The PCM will compensate for various engine loads
based on engine coolant temperature to keep the engine at the desired idle speed.
Driver Module 1 / 2 / 3 / 4 Status
Scan Tool Displays Enabled, Off-High Volts, Off High Temp or Invalid State. This parameter describes the internal PCM driver module condition.
This module controls all the relays/solenoids listed below the Driver Module parameter in the scan tool Output Driver Data List up to the next
driver module.
Engine Run Time
Scan Tool Displays 00:00:00-99:99:99 Hrs:Min:Sec. Indicates the time elapsed since the engine was started. If the engine is stopped, ENGINE
RUN TIME will be reset to 00:00:00.
Engine Speed
Scan Tool Displays 0-9999 RPM. Engine speed is computed by the PCM from the 3X reference input. The engine speed should remain close to
desired idle under various engine loads with engine idling.
Fuel Level
Scan Tool Displays 0-100 percent. The scan tool displays in percentage the amount of fuel in the fuel tank.
Fuel Trim Cell
Scan Tool Displays 0-9 Fuel trim cell is dependent upon engine speed and MAF sensor readings. A plot of RPM vs. MAF is divided into 10 cells.
Fuel trim cell indicates which cell is currently active.
IAC Position
Scan Tool Displays 0-255. Displays the commanded position of the idle air control pintle in counts. A larger number of counts means that more air
is being commanded through the idle air passage. IAC Position should respond fairly quickly to changes in engine load to maintain desired idle
RPM.
Knock Retard
Scan Tool Displays 0.0-25.5 degrees. Indicates the amount of spark the PCM is removing from IC spark advance in response to the signal from the
knock sensors. The Traction Control system Desired Torque signal from the EBTCM may cause Knock Retard to display a value greater than 0.0
degrees if Traction Control is active.
Loop Status
Scan Tool Displays OPEN or CLOSED. Closed Loop indicates that the PCM is controlling fuel delivery according to oxygen sensor voltage. In
Open Loop, the PCM ignores the oxygen sensor voltage and bases the amount of fuel to be delivered on TP sensor, engine coolant, and MAF
sensor inputs only.
Non-Volatile Memory
Scan Tool Displays Pass or Fail. Indicates the condition of the PCM's random access memory.
Spark
Scan Tool Displays -64 to 64 degrees. Displays the spark timing being commanded by the PCM on the IC circuit. A negative (-) value indicates
degrees Before Top Dead Center (BTDC) or spark advance. A positive value indicates degrees After Top Dead Center (ATDC) or spark retard.
Because the ignition control module sets spark advance at a fixed value of 10 degrees BTDC while operating in Bypass mode, the displayed Spark
advance only reflects true spark timing when the PCM has commanded IC mode.
Start-Up ECT
Scan Tool Displays -40°C to 151°C (-40°F to 304°F). Indicates the Engine Coolant Temperature (ECT) at the time that the vehicle was started.
Used by the HO2S diagnostic to determine if the last start-up was a cold start.
Start-Up IAT
Scan Tool Displays -40°C to 151°C (-40°F to 304°F). Indicates the Intake Air Temperature (IAT) at the time that the vehicle was started. Used by
the HO2S diagnostic to determine if the last start-up was a cold start.
TP Sensor
Scan Tool Displays 0.5-5.00 volts. The voltage being monitored by the PCM on the TP sensor signal circuit.
General Description
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 631
Chevrolet Venture V6-3.4L VIN E 2311
The Engine Scan Tool Data Definitions contain a brief description of all engine related parameters available on the scan tool. The list is arranged in
alphabetical order. A given parameter may appear in any one of the data lists. In some cases, a given parameter may appear more than once, or in
more than one data list. This provides a list with related parameters grouped together.

Mode 6 Data Page 1


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 632
Chevrolet Venture V6-3.4L VIN E 2312

Mode 6 Data Page 2


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 633
Chevrolet Venture V6-3.4L VIN E 2313

Mode 6 Data Page 3


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 634
Chevrolet Venture V6-3.4L VIN E 2314

Mode 6 Data Page 4


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 635
Chevrolet Venture V6-3.4L VIN E 2315

Mode 6 Data Page 5


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 636
Chevrolet Venture V6-3.4L VIN E 2316

Mode 6 Data Page 6


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 637
Chevrolet Venture V6-3.4L VIN E 2317

Mode 6 Data Page 7


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 638
Chevrolet Venture V6-3.4L VIN E 2318

Mode 6 Data Page 8


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 639
Chevrolet Venture V6-3.4L VIN E 2319

Mode 6 Data Page 9


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 640
Chevrolet Venture V6-3.4L VIN E 2320
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 641
Chevrolet Venture V6-3.4L VIN E 2321
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 1
Chevrolet Venture V6-3.4L VIN E 2322
Technical Service Bulletins

All Technical Service Bulletins:


Number Date Name
08-07-30-035B Nov 10 A/T - Water Or Coolant Contamination Information
05-06-04-022G Oct 10 Fuel System - TOP TIER Detergent Gasoline (Canada)
10-08-45-001B Oct 10 Electrical - Information For Electrical Ground Repair
10-08-44-006 Oct 10 Navigation - Report Missing/Inaccurate Nav. Map Info
00-08-48-005D Sep 10 Body - Vehicle Glass Distortion Information
04-08-50-006D Sep 10 Interior - Seat Cover Wrinkle/Crease/Burn Info
10-08-98-002 Aug 10 Body - Drilling High Strength Steel Using CryoCobalt(R)
03-00-89-008E Jul 10 Body - Metal Body Panel Corrosion Protection
06-08-51-005A Jun 10 Body - Hem Flange Sealer For Corrosion Protection
03-08-98-002B Jun 10 Body - Squeeze Type Resistance Spot Welding/Equipment
99-09-40-005F Jun 10 Restraints - Extender Availability For Seat Belt
02-08-42-001D Jun 10 Lighting - Headlamp Polycarbonate Lens Damage Prevention
06-03-10-010A Jun 10 Wheels - Changing Procedures/Precautions
10-00-89-010 May 10 Locks - Key Code Security Rules and Information
00-03-10-006F May 10 Wheels/Tires - Tire Radial Force Variation (RFV)
04-06-01-029E Apr 10 Vehicle - Engine Crankcase and Subsystems Flushing Info.
05-03-10-020C Apr 10 Wheels/Tires - Use of Nitrogen Gas in Tires
04-03-10-001F Apr 10 Tires/Wheels - Tire Puncture Repair Procedures
08-03-10-006C Apr 10 Tires/Wheels - Tire Slowly Goes Flat/Warning Light ON
05-03-10-003F Apr 10 Tires/Wheels - Low Tire/Leaking Cast Aluminum Wheels
10-08-110-001 Mar 10 Interior - Proper Use of Floor Mats
00-03-10-002E Mar 10 Wheels - Chrome Wheel Staining/Pitting/Corrosion
10-08-50-003 Mar 10 Restraints - Driver/Passenger Seat Head Rest Information
08-08-64-011A Feb 10 Mirrors - Heated Mirrors, Defrosting Time
03-08-48-006G Feb 10 A/C - Window Defroster Contact/Tab Repair Information
06-08-50-009E Feb 10 Restraints - Passenger Presence System Information
00-07-30-009D Feb 10 A/T - Goodwrench Transmission Replacement
01-07-30-042F Feb 10 A/T - 2-3 Upshift or 3-2 Downshift Clunk Noise
00-06-01-026C Feb 10 Engine - Intake Manifold Inspection/Replacement
99-08-51-007D Jan 10 Wheel - Refinishing Aluminum Wheels
09-03-10-017 Dec 09 Wheels/Tires - Replacement Wheel Weight Information
06-08-43-003B Nov 09 Wipers/Washers - Windshield Wiper Maintenance/Cleaning
99-04-20-002F Nov 09 Drivetrain - Clunk Noise Shifting From PARK Into Gear
06-08-64-001B Oct 09 Body - Side Window Chipping Information
05-03-08-002C Oct 09 Suspension - Shock Absorber/Strut Leakage Information
06-08-111-004B Sep 09 06-08-111-004B - BULLETIN CANCELLATION NOTIFICATION
09-08-48-006 Sep 09 Body - Stain/Film On Windshield Glass Perimeter
02-07-30-052F Sep 09 A/T - Fluid Oil Cooler Flush
04-06-04-047I Aug 09 Fuel System - 'TOP TIER' Detergent Gasoline Information
06-02-32-013B Aug 09 Steering - Power Steering Pump Replacement Tips
03-03-10-007E Aug 09 Wheels/Tires - OE Tire/Wheel Characteristics
03-07-29-004F Jul 09 M/T - Operating Characteristics
99-08-64-016C Jul 09 Body - Maintaining Exterior Weatherstrip Appearance
08-06-01-008A Jul 09 Engine - Drive Belt Misalignment Diagnostics
07-06-01-016B Jul 09 Engine - Noise/Damage Oil Filter Application Importance
08-03-10-004A Jul 09 Wheels/Tires - Accessory Wheel & Tire Information
05-08-51-008C Jun 09 Body - Bumps or Rust Colored Spots in Paint
08-08-42-005B Jun 09 Lighting - Headlamp Warranty Replacement Guideline
99-01-39-004C Jun 09 A/C - Musty Odors Emitted From (HVAC) System
08-08-42-005B Jun 09 Lighting - Headlamp Replacement Information
06-08-44-015B May 09 Audio System - Noise When Using Portable Playback Unit
01-08-42-001G May 09 Lighting - Exterior Lamp Condensation Guidelines
08-03-10-005A Mar 09 Wheels/Tires - Chrome/Steel Valve Stem Cap Precautions
00-05-22-002L Mar 09 Brakes- Disc Brake Warranty Service And Procedures
09-08-48-002A Mar 09 Body - Marks/Stains on Windshield When Wet
09-09-40-001 Feb 09 Restraints - Seat Belt Warning Lamp On/Buckling Issues
02-08-98-002C Feb 09 Body - Hem Flange Rust Repair Information
01-07-30-036H Jan 09 A/T Control - DTC P0756 Diagnostic Tips
07-08-98-001A Jan 09 Body - Non-Approval of Clipping For Collision Repair
00-00-90-002J Jan 09 Tires - Correct Inflation Pressure Information
07-08-64-022B Jan 09 Instruments - Unnecessary Park Assist Mirror Replacement
01-06-01-011E Dec 08 Gasoline Engine - Oil Consumption Guidelines
04-07-30-017B Nov 08 A/T - Revised Converter Check Valve/Cooler Line Fitting
08089C Nov 08 Campaign - Deactivation Of Analog OnStar(R)
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 2
Chevrolet Venture V6-3.4L VIN E 2323
Technical Service Bulletins

All Technical Service Bulletins:


Number Date Name

01-07-30-032E Sep 08 A/T - 4T65E Fluid Leaking From A/T Vent


00-00-89-027E Sep 08 Interior - Elimination Of Unwanted Odors
06-08-64-007A Sep 08 OnStar(R) - Analog Only Systems Information
05-03-10-005D Sep 08 Wheels/Tires - Upsized Wheel/Tire Characteristics
08-08-44-028 Aug 08 Audio - Inadvertent Steering Wheel Button Activation
08-08-46-004 Aug 08 OnStar(R) - Aftermarket Device Interference Information
08-08-44-026 Aug 08 Audio System - Refurbishing Radio Faceplates/Knobs
02-06-03-008D Jul 08 Charging System - Low Voltage Display/Battery Discharged
05-06-02-001A Jul 08 Cooling System, A/C - Aluminum Heater Cores/Radiators
05-03-07-009B Jun 08 Alignment - Specifications/Requirements/Recommendations
08-08-44-023 Jun 08 Navigation Radio - Adaptation After Radio/Battery R&R
05-00-89-072B Jun 08 Engine/Fuel System - Oil/Fuel Additive Information
00-07-30-022D Jun 08 A/T - 4L60/65E, No Reverse/2nd or 4th Gear
08-07-30-027 Jun 08 A/T - No Movement in Drive or 3rd Gear
08-07-30-026 May 08 A/T - Slight Vehicle Movement In Park At Start Up
08-03-16-003 May 08 Tire Monitor System - TPM Sensor Information
01-07-30-010C May 08 A/T - Torque Converter Replacement Information
04-06-04-036E May 08 Emission - Emissions Programming Warranty Coverage
03-07-30-007E May 08 A/T - Gear Engagement Time Information
99-07-30-030F May 08 A/T - Grinding/Growling Noise in Park on Incline
05-06-03-002C Apr 08 Battery/Charging System - Electrical Diagnostics Info.
02-06-03-009C Apr 08 Electrical - Battery Charging Tips/Recommendations
02-06-01-003B Apr 08 Engine - Revised Cylinder Head Bolt Torque/Sequence
00-06-01-012C Apr 08 Engine - Use of 'Surface Conditioning Disks'
03-06-01-010C Apr 08 Engine/Cooling System - Oil or Coolant Leaks
08-08-51-002 Mar 08 Body - TPO Fascia Cleaning Prior to Painting
08-09-41-003 Feb 08 Restraints - Usage of Used/Salvaged/Imitation Components
05-00-89-078B Feb 08 Fuel System - GM Fuel System Treatment PLUS(R) Info.
06-06-04-035A Feb 08 Fuel System - E85 Fuel Usage Precaution
04-03-10-012B Feb 08 Wheels - Chrome Wheel Brake Dust Accumulation/Pitting
99-08-52-005C Jan 08 Keyless Entry System - Characteristics of Operation
08-01-38-001 Jan 08 A/C - Refrigerant Recovery/Recycling/Equipment
05-06-02-002B Jan 08 Cooling System - DEX-COOL(R) Coolant Leak Detection Dye
00-08-46-004C Jan 08 OnStar(R) - Re-establishing OnStar(R) Communications
01-08-46-008D Jan 08 01-08-46-008C BULLETIN CANCELLATION NOTICE
02-08-46-006C Jan 08 OnStar(R) - Incorrect GPS Position Reported During Call
05-08-46-004B Jan 08 OnStar(R) - Number Incorrect/Incorrectly Assigned
07-06-01-023 Dec 07 Engine - Oil Leaks From Front Crankshaft Seal
04-07-30-037D Nov 07 A/T - DEXRON(R)-VI Fluid Information
05-06-01-019F Oct 07 Engine - Oil Leaks from Crankshaft Rear Main Seal
05-06-01-010B Sep 07 Engine - Sealant Usage/Procedures
07-08-45-002 Sep 07 Electrical - Aftermarket Fuse Warning
05-06-04-035C Jul 07 Fuel System - E85 Fuel Usage Precautions
07-08-63-001 Apr 07 Body - Polypropylene Energy Absorber Replacement
07-08-44-007 Apr 07 Navigation System - Replacement Navigation Discs
02-08-42-004A Mar 07 Instruments - Reduced PRNDL Display Visibility
04-07-30-013B Feb 07 Engine, A/T - Shift/Driveability Concerns/MIL ON
04-06-04-054A Jan 07 Engine Controls - Aftermarket Accessory Usage
01-08-51-004E Dec 06 Body - Premature Aluminum Hood Blistering
06-08-46-007 Dec 06 OnStar - Analog-Only Systems Information
06-00-89-054 Nov 06 Warranty - Claims Submission
01-07-31-002B Nov 06 M/T - Hydraulic Clutch Bleeding Procedure Improvement
00-06-04-033B Oct 06 Emissions - OBDII I/M Readiness Testing
02-08-98-001C Oct 06 Body - Metal Panel Adhesive Bonding Information
01-08-45-005E Aug 06 Electrical - Hard or No Start/Warning Lamps ON/DTC's Set
00-06-02-006D Aug 06 Cooling System - Coolant Recycling Information
06-06-04-037 Aug 06 Engine Controls - MIL Function During I/M Testing
06-01-39-007 Jul 06 A/C - Contaminated R134A Refrigerant
04-07-30-037B Jun 06 A/T - DEXRON(R) VI Fluid Availability
03-07-30-043A May 06 A/T - Shift Lock Control Feature Function
06-08-45-004 May 06 Electrical - Instrument Panel & General Wiring Repair
01045B Apr 06 Campaign - Closure Announcement
02-08-46-004A Apr 06 Cell Phone - Error Messages, Bulletin Cancellation
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 3
Chevrolet Venture V6-3.4L VIN E 2324
Technical Service Bulletins

All Technical Service Bulletins:


Number Date Name

02-08-48-001B Mar 06 Body - Urethane Adhesives for Glass Applications


06-03-10-004 Mar 06 Tires/Wheels - Wheel Weight Usage Precautions
02-06-05-004B Feb 06 Accessories - DTC's P0300, P1380, P1381
04-07-30-028A Jan 06 A/T - 4T65-E Fluid Leaks From Reverse Servo Cover
04-06-04-051B Jan 06 Fuel System - Fuel Injector Maintenance Cleaning
99-08-51-001A Nov 05 Body - Paint-Less Dent Repair Recommendations
02-01-39-004B Nov 05 A/C - New PAG Oil
01-07-30-041B Oct 05 A/T - Diagnosing Fluid Leaks
03-06-04-012A Aug 05 Electrical - Harness Connection Inspection
04-05-23-002A Aug 05 Brakes - Minimum Allowable Rotor Thickness
04-08-48-001B Jun 05 A/C - Broken Rear Window Defogger Grid Detection
05-06-02-007 Jun 05 Cooling System - Revised Thermostat Replacement
04110 May 05 Recall - Power Sliding Door Interior Handle Replacement
05-06-04-028 Apr 05 Engine Controls - OBD System Monitor Operation
99-09-40-004A Apr 05 Restraints - Child Seat Top Teather Attachment Kits
00-08-46-002A Apr 05 OnStar(R) - Cellular Antenna Replacement Parts
03-05-24-001A Mar 05 Brakes - Wheel Cylinder Inspection Guidelines
99-08-46-001A Mar 05 OnStar(R) - Dealer Kits No Longer Available
01-08-46-004A Mar 05 OnStar(R)/Cell Phone - Integration
01-08-46-001A Mar 05 OnStar(R) - Configuration After Module Replacement
00-08-46-003B Feb 05 Instruments - GPS System Performance Degradation
03-09-41-003A Feb 05 Restraints - Air Bag System Diagnostics
02-08-58-005B Feb 05 Body - Wind Noise From Windshield Base
00-09-40-001C Jan 05 Restraint Systems - Excessive Child Seat Movement
NHTSA04V597000 Dec 04 Recall 04V597000: Power Sliding Door Interior Handle
01-01-38-006D Sep 04 A/C - R-134a System Flushing Procedures
01-03-10-009A Jul 04 Wheels - Plastic Wheel Nut Covers Loose/Missing
02-06-03-010A Jul 04 Battery - Parasitic Drain
04-06-00-047 Jun 04 Fuel - Top Tier Detergent Gasoline Information
04-08-98-001 May 04 Body - Metal Panel Bonding Additional Material
04-06-01-013 Apr 04 Engine - Serpentine Drive Belt Wear Information
04-07-30-006 Feb 04 A/T - 4L65E, 4L60E, 4L60, 200-4R Oil Pump Spring
03-08-42-007A Jan 04 Lighting - Tail/Brake Lamp Bulb Inoperative
04-01-37-001 Jan 04 A/C - Control Knob Replacement Availability
04-09-40-001 Jan 04 Restraint System - 2nd Row Seat Belt Won't Release
03-02-32-049 Oct 03 Steering - New Outer Tie Rods/Replacement Procedure
01-01-38-013A Oct 03 A/C - Unnecessary Compressor Replacement
02-07-30-022B Oct 03 A/T - MIL/SES Lamp ON/Multiple A/T DTC's Set
01-01-39-003A Jul 03 A/C - Catastrophic Compressor Failure Debris Removal
02-08-98-003 Jun 03 Body - Information On Expandable Acoustic Foam
03-07-30-027 Jun 03 A/T - Oil Cooler Flushing Frequently Asked Questions
03-07-30-017 May 03 A/T - Grinding Noise/No Vehicle Movement in 'D' or 'R'
02-08-67-006B Mar 03 Body - Front/Rear Roof Rust Perforation
03-01-38-001 Mar 03 A/C - System Sealers/Leak Detection Guidelines
99-01-39-007B Mar 03 A/C - Automatic A/C Functional Description
99-07-30-017A Feb 03 A/T - Oil Cooler Flushing/Flow Check Procedures
03-06-01-002 Feb 03 Engine - New Polymer Coated Piston and Rod Assembly
02-07-30-048 Nov 02 A/T - Pressure Control Solenoid Replacement
02-06-04-053 Oct 02 Emissions - Revised DTC P0403 (EGR Solenoid Circuit)
02-06-01-028 Aug 02 Engine - Crankcase Flushing Recommendations
02-07-30-014A Jul 02 A/T - 4T65-E Spacer Plate/Gasket Service
00-07-30-002B Jul 02 A/T - 4T65E Harsh Shifts/Shudders/Slips/DTC's Set
02-08-47-001 Jul 02 Body Control - Update of Some Control Module DTC's
02-07-30-028 Jun 02 A/T - Serial Number/Site Code Locations/Identification
02-09-41-001 Jun 02 Computers & Controls - DTC's Set When Replacing Modules
02-08-58-003 Jun 02 Interior - Road Noise Heard From Behind Front Seats
02-06-01-026 Jun 02 Engine - Identification Information
02-07-30-014 Apr 02 A/T - 4T65-E Spacer Plate Service
02-06-01-008 Mar 02 Engine - New Prelube Tool
00-07-30-007A Feb 02 A/T - 4T65E, MIL ON/Whine Noise In PARK/NEUTRAL
02-08-56-001 Feb 02 PASS-KEY III - Revised Relearn Procedure
01-05-23-011A Feb 02 Brakes - Rattling Noise
99-00-89-019B Feb 02 Warranty - Parts Return Program Explained
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 4
Chevrolet Venture V6-3.4L VIN E 2325
Technical Service Bulletins

All Technical Service Bulletins:


Number Date Name

01-08-46-006A Dec 01 Onstar(R) - Antenna Coupling Revised Procedures


01-03-10-011 Dec 01 Tires - Sidewall Damage
01-08-97-002 Nov 01 HomeLink(R) Transmitter - Programming Difficulties
01-06-04-044 Nov 01 EVAP System - Special Tool Usage
01-08-57-006 Nov 01 Body/Frame - Mildew Odor, Water Leaks
01059 Oct 01 Recall - Defective Power Sliding Door
01-07-30-029 Oct 01 A/T - Core Return Product Feedback Form
00-06-04-011A Oct 01 EVAP System - Monitor Strategy
01-01-38-011 Oct 01 A/C System - Proper Use to Achieve Maximum Cooling
01-09-41-008 Sep 01 Side Impact Air Bag Inflator Module - Replacement Update
01-00-89-013 Sep 01 RKE Transmitter - Correct Use of Labor Operation R4490
NHTSA01V264000 Aug 01 Recall 01V264000: Sliding Door Defect
01-09-40-002 Jun 01 Seat Belt System - Collision Replacement Guidelines
01-08-44-006A Jun 01 Audio System - Clearing `CLN' Message From Display
99-06-03-010A Jun 01 PCM/BCM Replacement - DTC's B001/B1271/B1780 Set
01-05-23-006A Jun 01 Brake Calipers - Revised Fastener Requirements
01-00-89-010 Jun 01 Diagnostic Worksheet - Usage
01-00-89-009 May 01 Key/Key Number/Security Chip - Replacement
01-06-03-005 May 01 Interior/Exterior Lamps - Flicker
00-03-10-003B May 01 Tires - Bumper To Bumper Warranty Coverage
99-07-30-020A Apr 01 A/T - Service Procedure Changes
01-08-61-003 Apr 01 Special Tools - Frame Insulator Tool
01-02-32-004 Apr 01 Special Tools - Power Steering System Analyzer
NHTSA01V067000 Mar 01 Recall 01V067000: Sliding Doors May Not Latch
99-08-44-001B Mar 01 Video Entertainment System - Exchange Program
01-05-23-003 Mar 01 Front/Rear Brakes - Revised Tool Requirements
00-08-64-015A Feb 01 Power Sliding Side Door - Edge Guard Comes Loose
00-00-90-001 Nov 00 Suspension - Chassis Lubrication Importance
99-05-25-003A Oct 00 Brakes - ABS Exchange Program Ended
00-08-51-001 Sep 00 Outside Rear View Mirror - Housing Turns Chalky/Dull
00-01-38-007 Sep 00 A/C Performance/Leaks - Diagnostic Procedure
NHTSA00V228003 Aug 00 Recall 00V228003: Seat Belt Buckle Defect
00-00-89-021 Aug 00 Cross Line - Warranty Information
00-06-04-026 Jun 00 PCM - Returned Product Feedback Program
00-08-42-003 Jun 00 Headlamp - Capsule Now Available
00-08-64-007 Jun 00 Front Door Window - Inoperative/Slow or Noisy
99-01-38-006A May 00 A/C - Refrigerant Recovery/Recharge Equipment
00-06-02-004 May 00 Radiator - Brown Substance On Cap & Upper Filler Neck
00-06-04-021 May 00 EVAP System - Service of Connectors
00-06-03-003 May 00 Battery - Testing and Replacement
00-05-22-004 May 00 Brake Fluid - Level & Filling Recommendations
99-00-84-021B Apr 00 Warranty - GM Dealer Parts Procurement
00-06-02-001 Jan 00 Engine - Running Hot And/Or Loss of Coolant
99-09-41-004 Jan 00 Air Bag (SIR) On-Off Switch Kits, New Parts and Service
00-01-38-001 Jan 00 A/C - Lack of Performance in Hot/Humid Weather
99-06-03-012 Dec 99 Battery - Testing & Replacement
99-08-45-005 Nov 99 Accessory Receptacle/Cigar Lighter - Inoperative
99-08-42-009 Nov 99 IP Dimmer Control - Proper Setting
99-06-04-053 Nov 99 PROM - Powertrain Control Module Reprogramming
99-03-10-104 Nov 99 Tires - Improper/Recommended Tire Pressure
NHTSA99V268000 Oct 99 Recall 99V268000: Fuel Tank Inspection/Replacement
99-08-44-008 Oct 99 Cassette Player - Cleaning and Maintenance
99-06-03-011 Oct 99 Warranty - Generator Replacement
99-03-10-103 Oct 99 Wheels - Stud Removal Tool Change
99-06-02-017 Oct 99 Cooling - Radiator Repair/Replacement Guidelines
99-00-89-016 Sep 99 Warranty - Labor Time Guide Updates, 09/99
99-06-04-018 May 99 Fuel Pressure - Correct Operating Range
68-05-03 Jun 96 Warranty - Goodwrench Service Lifetime Service Guarantee
89358 Nov 88 Battery - Diagnosis and Charging
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 1
Chevrolet Venture V6-3.4L VIN E 2326
Vehicle: Technical Service Bulletins

How to Find Technical Service Bulletins by Category/Symptom


Selecting TSB's "By Symptom"

If you have a vehicle which displays system-related symptoms, this Manual provides a way to quickly search for any relevant Technical
Service Bulletins (TSB's). When you select TSB's "By Symptom," all relevant TSB's display at the top of the TSB title list. Viewing TSB's
by Symptom is helpful when the vehicle displays a distinct, system related, malfunction. You may also wish to review the symptom list with
your customer to uncover additional information that was not indicated on the Driveability Worksheet.

You can view TSB's by Symptom at any System or Sub-System level of the TurboView hierarchy. For example, a Symptom list will appear
when selecting Powertrain Management or Computers and Control Systems. Symptoms will not appear when selecting a component (such as
Mass Air Flow Sensor).

To view TSB's by Symptom:

1. Select the desired System or Sub-System and click the TSB icon.
2. Select "By Symptom" from the TSB list.
3. Select the symptom you wish to display.
4. Click on the desired TSB to display the article

Example:

Your customer complains of a noise in his 1989 Toyota Corolla (1.6L DOHC). The noise seems to be coming from the automatic
transmission. To find TSB's related to transmission noise:

1. Select Transmission and Drivetrain, then Automatic Transmission.


2. Click the TSB icon and select "Noise" from the TSB symptom list.
3. Notice that TSB's related to transmission noise are now located at the top of the TSB title list while non-related TSB's for the transmission
are listed below.

Technical Service Bulletin # 01045B Date: 060421

Campaign - Closure Announcement


Subject:
Customer Satisfaction - OnStar Global Positioning System (GPS)
# 01045B - (04/21/2006)

Models:
2000 GMC Yukon, Yukon XL, Denali, Envoy, Jimmy
2000 Cadillac Escalade, DeVille, Seville, Eldorado, Catera
2000 Buick Park Avenue, LeSabre, Century, Regal
2000 Oldsmobile Bravada, Silhouette, Intrigue
2000 Pontiac Bonneville, Montana, Grand Prix
2000 Chevrolet Blazer, Suburban, Tahoe, Venture, Impala, Lumina, Monte Carlo
2001 Pontiac Aztek

This bulletin is being revised to announce the closure of this recall. Please discard all copies of recall bulletin 01045A, issued July, 2002.

Please be advised that this recall has been officially closed. Owners of vehicles that were involved in this recall, but who did not respond to the
customer letters, have already been refunded their remaining subscription fees following the de-activation of their systems.

DisclaimerTechnical Service Bulletin # 08089C Date: 081118

Campaign - Deactivation Of Analog OnStar(R)


# 08089C: Special Coverage Adjustment - Analog OnStar Deactivation
(Nov 18, 2008)
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 2
Chevrolet Venture V6-3.4L VIN E 2327

Subject:
08089C -- SPECIAL COVERAGE ADJUSTMENT - ANALOG ONSTAR(R) DEACTIVATION
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 3
Chevrolet Venture V6-3.4L VIN E 2328

Models

The service procedure in this bulletin has been revised. Step 11 in the procedure for the 2004-2005 Saab 9-3 (9440) Convertible has been revised.
Discard all copies of bulletin 08089B, issued September 2008.

Condition

In November 2002, the U.S. Federal Commissions (FCC) ruled that wireless carriers would no longer be required to support the analog wireless
network beginning in 2008. As a result, On Star(R) is unable to continue analog service.

OnStar(R) has deactivated most of the systems operating in the analog mode; however, there are some vehicles that OnStar(R) could not deactivate.
Although the analog OnStar(R) hardware in these vehicles can no longer communicate with OnStar(R), the hardware in the vehicle is still active. If
the OnStar(R) emergency button is pressed, or in the case of an airbag deployment, or near deployment, the customer may hear a recording that
OnStar(R) is being contacted. However, since analog service is no longer available, the call will not connect to OnStar(R). To end the call, the
customer must press the white phone or white dot button. If the call is not ended, the system will continue to try to connect to OnStar(R) until the
vehicle battery is drained.

Special Policy Adjustment

At the customer's request, dealers/retailers are to deactivate the OnStar(R) system. The service will be made at no charge to the customer.

This special coverage covers the condition described above until December 31, 2008 for all non-Saab vehicles; April 30, 2009 for all Saab vehicles.

Vehicles Involved
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 4
Chevrolet Venture V6-3.4L VIN E 2329
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 5
Chevrolet Venture V6-3.4L VIN E 2330
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 6
Chevrolet Venture V6-3.4L VIN E 2331
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 7
Chevrolet Venture V6-3.4L VIN E 2332
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 8
Chevrolet Venture V6-3.4L VIN E 2333
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 9
Chevrolet Venture V6-3.4L VIN E 2334
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 10
Chevrolet Venture V6-3.4L VIN E 2335
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 11
Chevrolet Venture V6-3.4L VIN E 2336
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 12
Chevrolet Venture V6-3.4L VIN E 2337
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 13
Chevrolet Venture V6-3.4L VIN E 2338

Involved are certain vehicles within the VIN breakpoints shown above.

PARTS INFORMATION -- Saab US Only

Customer Notification

General Motors will notify customers of this special coverage on their vehicles (see copy of typical customer letter shown in this bulletin - actual
divisional letter may vary slightly).
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 14
Chevrolet Venture V6-3.4L VIN E 2339
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 15
Chevrolet Venture V6-3.4L VIN E 2340
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 16
Chevrolet Venture V6-3.4L VIN E 2341

Claim Information - GM, Saturn Canada and Saab Canada Only

Claim Information - Saturn US Only

Customer Reimbursement Claims - Special Attention Required

Customer reimbursement claims must have entered into the "technician comments" field the CSO # (if repair was completed at a Saturn Retail
Facility) date, mileage, customer name, and any deductibles and taxes paid by the customer.

Claim Information - Saab US Only


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 17
Chevrolet Venture V6-3.4L VIN E 2342

1. To receive credit, submit a claim with the information above.

Disclaimer

2001 and Older Model Year Vehicles (Except Saab Vehicles)


2001 and Older Model Year Vehicles (Except Saab Vehicles)

Important:
2001 and older model year vehicles require the removal of the battery power from the OnStar(R) vehicle interface unit (VIU) to eliminate
the possibility of an inadvertent OnStar(R) or emergency/airbag call.

1. Locate and gain access to the OnStar® VIU. Refer to OnStar Vehicle Interface Unit Replacement in SI.

Important:
Complete removal of the VIU is usually not required. Perform only the steps required to gain access to the C2 32-way blue connector.
Residing in the C2 connector are the battery positive (+) circuits. Removal of the C2 connector will deactivate the unit and eliminate the
possibility of an inadvertent OnStar(R) or emergency/airbag call.

2. Disconnect the C2 32-way blue connector from the VIU and tape the connector to a secure location. Refer to Cellular Communications
Connector End Views and related schematics in SI, if required.

Important:
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 18
Chevrolet Venture V6-3.4L VIN E 2343
DO NOT perform the OnStar(R) reconfiguration and/or programming procedure.

3. Secure the VIU in its original brackets and/or mounting locations and reinstall the VIU and interior components that were removed to gain
access to the VIU. Refer to OnStar Vehicle Interface Unit Replacement in SI.

2002 Through 2006 Model Year Vehicles (Except Saab Vehicles)


2002 through 2006 Model Year Vehicles (Except Saab Vehicles)

Important:
The Tech 2 diagnostic tool must be updated with version 28.002 or later in order to successfully perform the VCIM setup procedure and
disable the analog system.

1. Connect the Tech 2 to the data link connector (DLC), which is located under the instrument panel of the vehicle.

2. Turn the Tech 2 ON by pressing the power button.

Important:
Tech 2 screen navigation to get to the setup procedure depends on the year and make of the vehicle. The actual name of the setup
procedure (Setup New OnStar or VCIM Setup) depends on model year and vehicle make as well. Example Tech 2 navigation to the setup
procedure Tech 2 screen is provided below.

^ Diagnostics >> (2) 2002 >> Passenger Car >> Body >> C >> OnStar >> Special Functions >> Setup New OnStar >>

^ Diagnostics >> (5) 2005 >> Passenger Car >> (4) Buick >> C >> Body >> Vehicle Comm. Interface Module >> Module Setup >>
VCIM Setup >>

3. Setup VCIM using the Tech 2. Follow on-screen instructions when you have reached the setup Tech 2 screen.

2000-2002 Saab 9-3 (9400) 4D/5D; 2000-2003 Saab 9-3 (9400) CV


2000-2002 Saab 9-3 (9400) 4D/5D; 2000-2003 Saab 9-3 (9400) CV

1. Remove the ground cable from the battery's negative terminal.

2. Apply the handbrake brake.

3. Detach the floor console.

4. Remove the switch and the floor console:

3.1. Twist loose the immobilizer unit (A), bayonet fitting. Unplug the unit's connector.

3.2. Remove the ignition switch cover (B) by first undoing the rear edge of the cover and then unhooking the front edge. Unplug the
ignition switch lighting connector.

3.3. Undo the floor console's retaining bolts (C).

3.4. Take out the rear ashtray/cover (D).

3.5. Remove the screw (E) for the rear cover.

3.6. Remove the floor console's retaining nuts (E).


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 19
Chevrolet Venture V6-3.4L VIN E 2344

3.7. Detach the floor console (G) by pulling it straight back and lifting it slightly.

3.8. If required, detach the switch for the rear seat heater and unplug the connector.

4. Remove the switch and the floor console:

4.1. Detach the window lift module (A) by loosening it in the front edge (snap fastener). Unplug the window lift module's connector.

4.2. Detach the switch for the roof lighting (B) and unplug its connector. Lift away the floor console.

5. Pry out the signal line from the SRS control module to the OnStar(R) control module and secure it:

5.1. Unplug the SRS control module's connector (A).

5.2 Cut off the cable tie (B), detach the connector's rear end face (C) and pull out the connecting rail (D).
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 20
Chevrolet Venture V6-3.4L VIN E 2345

5.3. Remove pin 39, cut off the cable terminal and insulate the end with tape (E). Fold back the cable and secure it with tape (F).

5.4. Fit the connecting rail and end face.

5.5. Plug in the connector (A) and secure the cables with cable ties (B).

6. Install the floor console over the handbrake. Do not press the console down into place, but instead allow it to fit loosely.

7. Install the switch:

7.1. Install the switch for the roof lighting (B) and plug in its connector.

7.2. Guide the connectors for the window lift module and rear seat heater, if equipped, through the hole for each respective unit. Plug in the
window lift module's connector and install the module (A).

7.3. If equipped, connect the rear seat heater's connector and install the switch.

8. Install the floor console:


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 21
Chevrolet Venture V6-3.4L VIN E 2346

8.1. Install the floor console's retaining bolts (C) and retaining nuts (F).

8.2. Align the rear cover; make sure that the air duct connects firmly to the air nozzle. Screw in the cover (E).

8.3. Install the ashtray/cover (D).

8.4. Install the ignition switch cover (B).

8.5. Plug in the immobilizer unit (A) connector. Install the unit, bayonet fitting.

9. Remove the OnStar(R) control modules and secure the wiring:

9.1. Remove the right-hand rear luggage compartment trim in accordance with WIS - 8.

Body - Interior equipment - Adjustment/Replacement.

9.2. Unplug the connectors (A) from the OnStar(R) control modules.

9.3. Remove the console (B) together with the OnStar(R) control modules.

Important:
Secure the wiring harness so that there is no risk of chafing and rattling.

9.4. Fold back the wiring harness and tape over the connectors (C). Fold back the wiring harness once more and secure with cable ties (D).

9.5. Install the right-hand rear luggage compartment in accordance with WIS - 8. Body - Interior equipment - Adjustment/Replacement.

10. Install the ground cable to the battery's negative terminal.

11. Clear the diagnostic trouble codes.

12. Set the date and time, see WIS - 3. Electrical system - Information display (SID_ - Technical description.
2003-2005 Saab 9-3 (9400) 4D/5D; 2004-2005 Saab 9-3 (9400) CV
2003-2005 Saab 9-3 (9440) 4D/5D; 2004-2005 Saab 9-3 (9440) CV

Notice:
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 22
Chevrolet Venture V6-3.4L VIN E 2347
Handle the fiber optic cables with care or the signal may be distorted.

^ It is very important that the two leads in the connector are not confused with one another.

^ Do not splice the cables.

^ Do not bend the cable in a radius smaller than 25 mm (1 in).

^ Do not expose the cable to temperatures exceeding 185°F (85°C).

^ Keep the cable ends free from dirt and grime.

^ Do not expose the cable to impact as this may cause the transparent plastic to whiten, thereby reducing the intensity of the light and
causing possible communication interruptions.

^ The cable should not lie against any sharp edges as this may cause increased signal attenuation.

1. Remove the ECU CU with a Tech 2(R) according to the following: Fault diagnosis - Select model year - Select Saab 9-3 Sport (9440) - All -
Add/Remove - Control Module - CU/PU - Remove.

2. Remove the ground cable from the battery's negative terminal.

3. Remove the floor console in accordance with WIS - 8. Body - Interior equipment - Adjustment/Replacement.

4. Pry out the signal line from the SRS control module to the OnStar(R) control module and secure it:

4.1. Unplug the SRS control module's connector (A).

4.2. Cut off the cable tie (B), detach the connector's rear end face (C), and pull out the connecting rail (D).
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 23
Chevrolet Venture V6-3.4L VIN E 2348

4.3. Extract pin 15, cut off the cable terminal and insulate the end with tape (E). Fold back the cable and secure it with tape (F).

4.4. Fit the connecting rail and end face.

4.5. Plug in the connector (A) and secure the cables with cable ties (B).

5. Remove the parcel shelf trim in accordance with WIS - 8. Body - Interior equipment - Adjustment/Replacement.

6. M03: Replace the optic cable on the right-hand side

Important:
Secure the wiring harness so that there is no risk of chafing or rattling.

6.1. Remove the passenger seat in accordance with WIS 8. Body - Seats - Adjustment/Replacement.

6.2. Remove the right-hand B-pillar trim in accordance with WIS - 8. Body - Interior equipment - Adjustment/Replacement.

6.3. Remove the right-hand C pillar trim in accordance with WIS - 8. Body - Interior equipment - Adjustment/Replacement.

6.4. Fold the rear seat backrest forward.

6.5. Remove the right-hand side bolster in accordance with WIS - 8. Body - Seats - Adjustment/Replacement.

6.6. Remove the A-pillar's lower side piece.

6.7. Open the cover on the right-hand wiring harness channels.

6.8. Loosen the locking strip (A) on the 2-pin connector (H2-11) for the optic cable, located by the right-hand A-pillar.

6.9. Loosen the catch (B) and remove the optic cable that runs backward in the car.

6.10. Dismantle the end cap from the new optic cable (12 783 577) and connect it to the connector H2-11. Push in the optic cable and make
sure the catch (B) locks and refit the locking strip (A).
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 24
Chevrolet Venture V6-3.4L VIN E 2349

6.11. Secure the connector and the old optic cable using the cable tie for the existing wiring harness (C).

Important:
The optic cable must not be bent with a radius less than 25 mm (1 in).

6.12. Place the optic cable in the wiring harness channels on the right-hand side. Thread through the existing cable ties (C) if possible,
otherwise, secure with a cable tie to the existing one. Close the cover on the channels. Ensure the catches lock.

6.13. Secure the optic cable along the right-hand rear wheel housing, next to the ordinary wiring harness securing points and by the SRS unit
(D).

6.14. Thread the optic cable up next to the safety belt by the old optic cable and place on the parcel shelf.

6.15. Unplug the connectors (E) from the OnStar(R) control modules.
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 25
Chevrolet Venture V6-3.4L VIN E 2350

6.16. Remove the console (F) together with the OnStar(R) control modules.

Important:
The optic cable must not be bent with a radius less than 25 mm (1 in).

6.17. Fold back the wiring harness and tape over the connectors (G). Fold back the wiring harness once more and secure with cable ties (H).

6.18. Secure the new optic cable on the parcel shelf along the existing wiring harness by the ordinary securing points and by the speaker (I).

6.19. Thread the optic cable down next to the old cable from the parcel shelf to the left-hand wheel housing, next to REC. The cable is
secured in the existing clips.

6.20. Fit the right-hand C-pillar trim in accordance with WIS - 8. Body - Interior equipment - Adjustment/Replacement.

6.21. Fit the parcel shelf trim in accordance with WIS - 8. Body - Interior equipment - Adjustment/Replacement.

6.22. Fit the passenger seat in accordance with WIS - 8. Body - Seats - Adjustment/Replacement.

6.23. Fit the right-hand side bolster in accordance with WIS - 8. Body - Seats - Adjustment/Replacement.

6.24. Fold up the rear seat backrest.

6.25. Fit the right-hand B-pillar trim in accordance with WIS - 8. Body - Interior equipment - Adjustment/Replacement.

6.26. Fit the A-pillar's lower side piece.

7. M04-05, 4D: Removing the OnStar® control modules and securing the wiring:
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 26
Chevrolet Venture V6-3.4L VIN E 2351

7.1. Remove the console (A) together with the OnStar(R) control modules.

7.2. Remove the connectors (B).

Important:
The optic cable must not be bent with a radius less than 25 mm (1 in).

Important:
Secure the wiring harness so that there is no risk of chafing and rattling.

7.3. Fold back the wiring harness and tape over the connectors (C). Fold back the wiring harness once more and secure with cable ties (D).

7.4. Fit the parcel shelf trim in accordance with WIS - 8. Body - Interior equipment - Adjustment/Replacement.

8. CV: Removing the OnStar(R) control modules and securing the wiring: Adjustment/Replacement.

8.1. Open the luggage compartment floor.


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 27
Chevrolet Venture V6-3.4L VIN E 2352

8.2. Remove the console (A) together with the OnStar(R) control modules.

8.3. Remove the connectors (B).

Important:
The optic cable must not be bent with a radius less than 25 mm (1 in).

Important:
Secure the wiring harness so that there is no risk of chafing and rattling.

8.4. Fold back the wiring harness and tape over the connectors (C). Fold back the wiring harness once more and secure with cable ties (D).

8.5. Close the luggage compartment floor.

9. Fold down the left-hand rear side hatch in the luggage compartment.
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 28
Chevrolet Venture V6-3.4L VIN E 2353

10. M03: Replace the optic cable on the left-hand rear side:

10.1. Place the optic cable so that it is positioned behind the terminal housing on top of REC (A).

10.2. Remove the locking strip (B) on the 2-pin connector (H2-9) for the optic cable.

10.3. Open the terminal housing (C) with a screwdriver. Remove the secondary catch (D) on the connector and disconnect the optic cable
coming from the OnStar(R) control modules.

10.4. Remove the end cap from the new optic cable, connect to the connector and refit the secondary catch (D). Fit the terminal housing (C)
to the connector and refit the locking strip (B).
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 29
Chevrolet Venture V6-3.4L VIN E 2354

10.5. Secure the old optic cable together with the new one (E).

Important:
The optic cable must not be bent with a radius less than 25 mm (1 in).

Important:
Secure the wiring harness so that there is no risk of chafing and rattling.

11. CV: Remove the rear seat in accordance with WIS - 8. Body - Interior equipment - Adjustment/Replacement. The O-bus connector H2-9 is
located behind the left speaker.

12. M04-05: Disconnect the optic cables on the OnStar(R) control modules and join the cables:

12.1. Cut off the cable tie holding the connector (H2-9) against REC.

12.2. Cars with brackets for e.g. an amplifier: Remove the pin strap (A) from the bracket and remove the tape (B) holding the optic cables.
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 30
Chevrolet Venture V6-3.4L VIN E 2355

12.3. Remove the locking strip (C) on the 2-pin connector (H2-9). Open the terminal housing with a screwdriver. Remove the secondary
catch (E) on the connector and remove the optic cables coming from the OnStar(R) control modules.

12.4. Loosen one of the optic cables remaining in H2-9 (F), connect it to the connector and fit the secondary catch (E). Connect the
connector so that the optic cables are opposite each other (G). Connect the terminal housing (D) and refit the locking strip (C).

Important:
The optic cable must not be bent with a radius less than 25 mm (1 in).

12.5. Cars with brackets for e.g. an amplifier: Fit the cable tie (11 900 515) to the wiring harness approx. 100 mm (4 in) from H2-9, fit the
cable tie (H) to the bracket. Gather the optic cable in a gentle loop (I) and then place the loop behind the bracket.
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 31
Chevrolet Venture V6-3.4L VIN E 2356

Important:
The optic cable must not be bent with a radius less than 25 mm (1 in).

12.6. Cars without brackets for e.g. an amplifier: Gather the optic cable in a gentle loop (J) and secure with cable tie.

13. CV: Fit the left-hand, rear side hatch trim in accordance with WIS - 8. Body - Interior equipment - Adjustment/Replacement.

14. Fit the ground cable to the battery's negative terminal.

15. Carry out procedures after disconnecting the battery, see WIS - 3. Electrical System - Charging system - Adjustment/Replacement.

Important:
Follow Tech 2(R) on-screen instructions.

16. Add ECU ICM, choose without OnStar(R). See WIS-General-Tech 2(R) - Description and Operation - Add/Remove.

2000-2004 Saab 9-5


2000-2004 Saab 9-5

1. Remove the ground cable from the battery's negative cable.

2. Remove the center console, see WIS - Body - Interior.

3. Loosen the gear shift housing (A).

AUT: Disconnect the 6-pin connector (B) to improve access to the gear shift housing screws.

4. Disconnect the signal cable from the SRS control module to the OnStar(R) control module and secure the cable.
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 32
Chevrolet Venture V6-3.4L VIN E 2357

4.1. Disconnect the connector (A) from the SRS control module and cut the cable tie (B).

4.2. Release the back end of the connector (C) and remove from the contact rail (D).

4.3. M00-01: Disconnect pin 39, cut off the cable terminal and insulate the end using tape (E). Fold back the cable and secure using tape
(F).

4.4. M02-04: Disconnect pin 58, cut off the cable terminal and insulate the end using tape (E). Fold back the cable and secure using tape
(F).

4.5. Assemble the contact rail and end.

4.6. Connect connector (A) and secure the cable using a cable tie (B).
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 33
Chevrolet Venture V6-3.4L VIN E 2358

5. Assemble the gear shift housing (A).

AUT: Connect connector (B).

6. Assemble the center console, see WIS - Body - Interior.

7. Remove the OnStar(R) control module and secure the cable harness:

7.1. 5D: Remove the right-hand cover from the luggage compartment floor.

7.2. Remove the console (A).

7.3. Disconnect the connector (B) from the OnStar(R) control module.
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 34
Chevrolet Venture V6-3.4L VIN E 2359

Important:
Secure the cable harness to prevent the risk of scraping and rattling.

7.4. Fold back the cable harness and tape down the connector (C). Fold back the cable harness again and secure with cable ties (D).

7.5. 5D: Assemble the right-hand cover for the luggage compartment floor.

8. Fit the ground cable on the battery's negative cable.

9. Erase the diagnostic trouble codes.

10. Set the date and time, see WIS - 3. Electrical system - Information display (SID) - Technical description.

Technical Service Bulletin # NHTSA99V268000 Date: 991011

Recall 99V268000: Fuel Tank Inspection/Replacement


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 35
Chevrolet Venture V6-3.4L VIN E 2360
NHTSA CAMPAIGN ID Number: 99V268000
Component: FUEL: VEHICLE CRASH, CUT OFF SYSTEM (5-94)
Manufacturer: GENERAL MOTORS CORP.

Year: 2000
Make: CHEVROLET TRUCK, PONTIAC TRUCK, OLDSMOBILE TRUCK
Model: VENTURE, MONTANA, SILHOUETTE
YEAR Of Recall: '99
Type of Report: Vehicle
Potential Number of Units Affected: 235

Summary:

Vehicle Description: Minivans with extended wheelbase.


Some of these vehicles have inoperative fuel tank rollover
valves and fuel leakage would exceed the permissible
amount in a rollover test. This does not comply with the
requirements of FMVSS No. 301, "Fuel system Integrity."

In a vehicle rollover accident, if an ignition source is


present, a fire could result.

Dealers will inspect the vehicle to locate and replace those


fuel tanks that could have inoperative rollover valves.

Owner notification began October 11, 1999. Owners who take


their vehicles to an authorized dealer on an agreed upon
service date and do not receive the free remedy within a
reasonable time should contact Chevrolet at 1-800-222-102 or
Pontiac at 1-800-762-2737, or Oldsmobile at 1-800-442-6537.
Also contact the National Highway Safety Administration's
Auto Safety Hotline at 1-888-DASH-2-DOT (1-888-327-4236). Technical Service Bulletin # NHTSA01V067000 Date: 010301

Recall 01V067000: Sliding Doors May Not Latch


Vehicle Description: Minivans equipped with passenger side power sliding doors. The door closes but may not be latched. If this happens, the
power sliding door can open while the vehicle is in motion, particularly when the vehicle ascends a hill, makes a turn, or travels over a rough road
surface. An unrestrained occupant could fall out of the van and be injured. Dealers will install a new un-latch actuator assembly to the power
sliding door.Owner notification began April 18, 2001. Owners who take their vehicles to an authorized dealer on an agreed upon service date and
do not receive the free remedy within a reasonable time should contact Chevrolet at 1-800-222-1020, Pontiac at 1-800-762-2737, or Oldsmobile at
1-800-442-6537. Also contact the National Highway Traffic Safety Administration's Auto Safety Hotline at 1-888-DASH-2-DOT
(1-888-327-4236).
Technical Service Bulletin # NHTSA04V597000 Date: 041221

Recall 04V597000: Power Sliding Door Interior Handle


MAKE/MODELS: MODEL/BUILD YEARS:

Chevrolet/Venture 1997-2005

Oldsmobile/Silhouette 1997-2004

Pontiac/Montana 1997-2005

Pontiac/Trans Sport 1999

Pontiac/Transport 1997-1998

MANUFACTURER: General Motors Corp.

NHTSA CAMPAIGN ID NUMBER: 04V597000 RECALL DATE: Dec 21, 2004

COMPONENT: Latches/Locks/Linkages: Doors: Latch

POTENTIAL NUMBER OF UNITS AFFECTED: 717302

SUMMARY:
On certain minivans equipped with second-row bucket seats or captain's chairs and a power sliding door on the passenger side of the vehicle, a
passenger using the interior handle to open the power sliding door could be injured.
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 36
Chevrolet Venture V6-3.4L VIN E 2361

CONSEQUENCE:
If a passenger uses the interior handle to open the power sliding door and holds onto the handle while it is being opened by the motor, the
passenger's arm may be pushed into the seat back or armrest and a wrist or lower arm injury may result.

REMEDY:
Dealers will replace the power sliding door interior handle on the passenger-side. If the vehicle is equipped with a power or manual sliding door on
the driver-side, the interior handle will also be replaced for appearance reasons. NOTE: Before the vehicle is serviced, GM advises owners to not
use the interior door handle to open the door. The driver can open and close the door from switches at the driver's position or by using the remote
key fob. The driver should tell passengers to use the switch located in front of the door to open or close it. The driver should use the override switch
to prevent operation of the power door by children or by others who are not familiar with its use. The recall is expected to begin in March 2005.
Owners should contact Chevrolet at 1-800-630-2438; Pontiac at 1-800-620-7668; or Oldsmobile at 1-800-630-6537.

NOTES:
GM recall No. 04110. Customers can also contact The National Highway Traffic Safety Administration's Auto Safety Hotline at
1-888-DASH-2-DOT (1-888-327-4236). Technical Service Bulletin # 04110 Date: 050524

Recall - Power Sliding Door Interior Handle Replacement


Right Hand Power Sliding Door Interior Handle
# 04110 - (May 24, 2005)

Models:
1997-2005 CHEVROLET VENTURE
1997-2004 OLDSMOBILE SILHOUETTE
1997-1998 PONTIAC TRANS SPORT
1999-2005 PONTIAC MONTANA

EQUIPPED WITH RIGHT-HAND POWER SLIDING DOOR AND SECOND ROW BUCKET SEATS OR CAPTAIN'S CHAIRS

DUE TO PART AVAILABILITY, THIS RECALL IS BEING ADMINISTERED IN PHASES. ALL VINS WILL BE LOADED INTO GMVIS:
HOWEVER, CUSTOMERS WILL BE NOTIFIED IN PHASES. YOU WILL BE NOTIFIED OF THE RELEASE OF ADDITIONAL PHASES
PRIOR TO CUSTOMER NOTIFICATION.

Condition

General Motors has decided that a defect, which relates to motor vehicle safety, exists in certain 1997-2005 Chevrolet Venture, 1997-2004
Oldsmobile Silhouette, 1997-1998 Pontiac Trans Sport, and 1999-2005 Pontiac Montana vehicles equipped with a right-hand power sliding door
and second row bucket seats or captains chairs. If a passenger uses the interior handle to open the power sliding door and holds onto the handle
while it is being opened by the door motor, the passenger's arm may be pushed into the seat back or armrest and a wrist or lower arm injury could
occur.

Until the vehicle is serviced, the interior handle should not be used to open the door. The driver can open and close the door from switches at the
driver's position or by using the remote key fob. The driver should tell passengers to use the switch located in front of the door to open or close the
door. The driver should also use the override switch to prevent operation of the power door by children or by others who are not familiar with its
use.

Correction

Although only the right-hand power sliding door handle requires replacement, dealers are to replace both rear door handles, if applicable, to keep
the appearance consistent

Vehicles Involved
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 37
Chevrolet Venture V6-3.4L VIN E 2362

Involved are certain 1997-2005 Chevrolet Venture, 1997-2004 Oldsmobile Silhouette, 1997-1998 Pontiac Trans Sport, and 1999-2005 Pontiac
Montana vehicles equipped with a right-hand power sliding door and second row bucket seats or captain's chairs, and built within these VIN
breakpoints shown.

Important:
Dealers should confirm vehicle eligibility through GMVIS (GM Vehicle Inquiry System) prior to beginning recall repairs. [Not all vehicles
within the above breakpoints may be involved.]

For US and Canada

For dealers with involved vehicles, a Campaign Initiation Detail Report containing the complete Vehicle Identification Number, customer name and
address data has been prepared and will be loaded to the GM DealerWorld (US) Recall Information, GMinfoNet (Canada) Recall Reports. Dealers
will not have a report available if they have no involved vehicles currently assigned.

For Export

For dealers with involved vehicles, a Campaign Initiation Detail Report containing the complete Vehicle Identification Number, customer name and
address data has been prepared, and is being furnished to involved dealers. Dealers will not receive a report with the recall bulletin if they have no
involved vehicles currently assigned.

The Campaign Initiation Detail Report may contain customer names and addresses obtained from Motor Vehicle Registration Records. The use of
such motor vehicle registration data for any purpose other than follow-up necessary to complete this recall is a violation of law in several
states/provinces/countries. Accordingly, you are urged to limit the use of this report to the follow-up necessary to complete this recall.
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 38
Chevrolet Venture V6-3.4L VIN E 2363

Parts Information

Parts required to complete this recall are to be obtained from General Motors Service Parts Operations (GMSPO). Please refer to your "involved
vehicles listing" before ordering parts. Normal orders should be placed on a DRO = Daily Replenishment Order. In an emergency situation, parts
should be ordered on a CSO = Customer Special Order.

Service Procedure

Tools Required

J 42506 Door Handle Clip Remover

1. Using the J 42506, Door Handle Clip Remover, remove the inside door handle clip.

2. Remove the inside handle from the sliding door and discard.

3. Load the clip into the inside door handle with the open end facing up.

4. Align the new handle with the shaft on the sliding door.

5. Press firmly in order to seat the inside handle on the sliding door.

6. Repeat the steps for the other door, if applicable.

Courtesy Transportation

The General Motors Courtesy Transportation Program is intended to minimize customer inconvenience when a vehicle requires a repair that is
covered by the New Vehicle Limited Warranty. The availability of courtesy transportation to customers whose vehicles are within the warranty
coverage period and involved in a product recall is very important in maintaining customer satisfaction. Dealers are to ensure that these customers
understand that shuttle service or some other form of courtesy transportation is available and will be provided at no charge. Dealers should refer to
the General Motors Service Policies and Procedures Manual for courtesy transportation guidelines.

Claim Information
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 39
Chevrolet Venture V6-3.4L VIN E 2364

Submit a Product Recall Claim with the information shown.

Customer Notification -- For US and Canada

General Motors will notify customers of this recall on their vehicle (see copy of customer letter shown in this bulletin).

Customer Notification -- For Export

Letters will be sent to known owners of record located within areas covered by the US National Traffic and Motor Vehicle Safety Act. For owners
outside these areas, dealers should notify customers using the sample letter shown.

Dealer Recall Responsibility -- For US and Export (US States, Territories, and Possessions)

The US National Traffic and Motor Vehicle Safety Act provides that each vehicle which is subject to a recall of this type must be adequately
repaired within a reasonable time after the customer has tendered it for repair. A failure to repair within sixty days after tender of a vehicle is prima
facie evidence of failure to repair within a reasonable time. If the condition is not adequately repaired within a reasonable time, the customer may
be entitled to an identical or reasonably equivalent vehicle at no charge or to a refund of the purchase price less a reasonable allowance for
depreciation. To avoid having to provide these burdensome remedies, every effort must be made to promptly schedule an appointment with each
customer and to repair their vehicle as soon as possible. In the recall notification letters, customers are told how to contact the US National
Highway Traffic Safety Administration if the recall is not completed within a reasonable time.

Dealer Recall Responsibility -- All

All unsold new vehicles in dealers' possession and subject to this recall MUST be held and inspected/repaired per the service procedure of this
recall bulletin BEFORE customers take possession of these vehicles.

Dealers are to service all vehicles subject to this recall at no charge to customers, regardless of mileage, age of vehicle, or ownership, from this time
forward.

Customers who have recently purchased vehicles sold from your vehicle inventory, and for which there is no customer information indicated on the
dealer listing, are to be contacted by the dealer. Arrangements are to be made to make the required correction according to the instructions
contained in this bulletin. A copy of the customer letter is shown in this bulletin for your use in contacting customers. Recall follow-up cards should
not be used for this purpose, since the customer may not as yet have received the notification letter.

In summary, whenever a vehicle subject to this recall enters your vehicle inventory, or is in your dealership for service in the future, please take the
steps necessary to be sure the recall correction has been made before selling or releasing the vehicle.

Disclaimer
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 40
Chevrolet Venture V6-3.4L VIN E 2365
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 41
Chevrolet Venture V6-3.4L VIN E 2366

Technical Service Bulletin # NHTSA00V228003 Date: 000817

Recall 00V228003: Seat Belt Buckle Defect


Passenger vehicles, light duty trucks, sport utility vehicles, and mini vans equipped with TRW seat belt buckle assemblies. The buckle base of these
seat belt assemblies were not properly heat treated and therefore do not pass the load bearing requirement of Federal Motor Vehicle Safety Standard
No. 209, "Seat Belt Assemblies."

In the event of a vehicle crash, the occupant may not be properly restrained.

Dealers will inspect the vehicle's rear safety belt buckle assembly date codes and, if necessary, will replace any rear safety belt buckle assembly.

Owner notification is expected to begin during August 2000. Owners who take their vehicles to an authorized dealer on an agreed upon service date
and do not receive the free remedy within a reasonable time should contact Buick at 1-800-521-7300; Chevrolet at 1-800-222-1020; GMC at
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 42
Chevrolet Venture V6-3.4L VIN E 2367
1-800-462-8782; Oldsmobile at 1-800-442-6537; Pontiac at 1-800-762-2737; or Saturn at 1-800-553-6000. Also contact the National Highway
Traffic Safety Administration's Auto Safety Hotline at 1-888-DASH-2-DOT (1-888-327-4236).
Technical Service Bulletin # NHTSA01V264000 Date: 010820

Recall 01V264000: Sliding Door Defect


Vehicle Description: 1997-2001 Chevrolet Venture, Pontiac Montana/Transport, and Oldsmobile Silhouette mini vans equipped with passenger
side power sliding doors, that were serviced in Campaign 01013 (01V-067) from April to August 2001. Also 2001 Chevrolet Venture, Pontiac
Montana, and Oldsmobile Silhouette mini vans equipped with passenger side power sliding doors assembled in January through April 2001. These
vehicles have inadequate front sonic welds. If a front sonic weld fails, the actuator can jam in the unlatched position and, when the sliding door
closes, it will not be latched.

If this happens, the power sliding door can open while the vehicle is in motion, particularly when the vehicle ascends a hill, makes a turn, or travels
over a rough road surface. An unrestrained occupant could fall out of the van and be injured.

Dealers will inspect the actuators for certain date codes and, if necessary, replace the actuators. GM has not yet provided an owner notification
schedule for this campaign. Owners who take their vehicles to an authorized dealer on an agreed upon service date and do not receive the free
remedy within a reasonable time should contact Chevrolet at 1-800-222-1020, Pontiac at 1-800-762-2737, or Oldsmobile at 1-800-442-6537. Also
contact the National Highway Traffic Safety Administration's Auto Safety Hotline at 1-888-DASH-2-DOT (1-888-327-4236). Technical Service
Bulletin # 01059 Date: 011001

Recall - Defective Power Sliding Door


File In Section: Product Recalls

Bulletin No.: 01059

Date: October 2001

PRODUCT SAFETY RECALL

SUBJECT:
01059 - POWER SLIDING DOOR

MODELS:
1997-2001 CHEVROLET VENTURE, PONTIAC MONTANA/TRANS SPORT, AND OLDSMOBILE SILHOUETTE "U" VAN WITH POWER
SLIDING DOORS (RPO E58 / E59)

Due to parts availability, ordering restrictions are being imposed to ensure an equitable distribution of part inventory. Refer to the Parts Information
section for details.

CONDITION

General Motors has decided that a defect which relates to motor vehicle safety exists in certain 1997-2001 Chevrolet Venture, Pontiac
Montana/Trans Sport, and Oldsmobile Silhouette model vehicles equipped with driver and/or passenger side power sliding doors. Some of the door
unlatch actuators in vehicles assembled in January-April 2001 and in vehicles that were serviced in Recall 01013 from April-August 2001 have
inadequate front sonic welds. If a front sonic weld fails, the actuator can jam in the unlatched position and, when the sliding door closes, it will not
be latched. If this happens, the power sliding door can open while the vehicle is in motion, particularly when the vehicle ascends a hill, makes a
turn, or travels over a rough road surface. An unrestrained occupant could fall out of the van and could be injured.

CORRECTION

Dealers are to inspect and if required, install a new power sliding door unlatch actuator assembly.

VEHICLES INVOLVED
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 43
Chevrolet Venture V6-3.4L VIN E 2368

Involved are certain 1997-2001 Chevrolet, Pontiac, and Oldsmobile "U" Van model vehicles equipped with RPO E58 or E59, power sliding doors,
and built within these VIN breakpoints shown.

The table shown contains VIN breakpoints for vehicles that were serviced under Recall 01013 from April-August 2001, and may have had suspect
actuators installed.

The table shown contains VIN breakpoints for vehicles specific to this Recall 01059, and were assembled in January-April 2001 and may have had
suspect actuators installed.

IMPORTANT:
Dealers should confirm vehicle eligibility through GMVIS (GM Vehicle Inquiry System) or GM Access Screen (Canada only) or DCS Screen
445 (IPC only) before beginning recall repairs. [Not all vehicles within the above breakpoints may be involved.]

Involved vehicles have been identified by Vehicle Identification Number. Computer listings containing the complete Vehicle Identification
Number, customer name and address data have been prepared, and are being furnished to involved dealers with the recall bulletin. The customer
name and address data furnished will enable dealers to follow up with customers involved in this recall. Any dealer not receiving a computer listing
with the recall bulletin has no involved vehicles currently assigned.

These dealer listings may contain customer names and addresses obtained from Motor Vehicle Registration Records. The use of such motor vehicle
registration data for any other purpose is a violation of law in several states/provinces/countries. Accordingly, you are urged to limit the use of this
listing to the follow-up necessary to complete this recall.

PARTS INFORMATION

Important:
An initial supply of RH actuator kits required to complete this recall will be pre-shipped the week of November 5, 2001 to dealers with claims
paid through April 30, 2001 for recall 01013. Pre-shipped parts will be charged to dealer's open parts account. Due to limited part supply, prior
to pre-ship, parts will be placed on an order writing control. Any orders prior to Nov. 5, 2001 will be canceled. After completion of the pre-ship,
a quantity limiter will be added to the part that will limit the pieces per order line. The reason this is being done is to facilitate an equitable
distribution of part inventory.

Additional parts, if required, are to be obtained from General Motors Service Parts Operations (GMSPO). Please refer to your "involved vehicles
listing" before ordering parts. Normal orders should be placed on a DRO = Daily Replenishment Order. In an emergency situation, parts should be
ordered on a CSO = Customer Special Order.
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 44
Chevrolet Venture V6-3.4L VIN E 2369

RECALL IDENTIFICATION LABEL - For US and IPC

Place a Recall Identification Label on each vehicle corrected in accordance with the instructions outlined in this Product Recall Bulletin. Each label
provides a space to include the recall number and the five (5) digit dealer code of the dealer performing the recall service. This information may be
inserted with a typewriter or a ball point pen.

Put the Recall Identification Label on a clean and dry surface of the radiator core support in an area that will be visible to people servicing the
vehicle. When installing the Recall Identification Label, be sure to pull the tab to allow adhesion of the clear protective covering. Additional Recall
Identification Labels for US dealers can be obtained from Dealer Support Materials by calling 1-866-700-0001 (Monday-Friday, 8:00 a.m. to 5:00
p.m. EST). Ask for Item Number 5-1015 when ordering.

Additional Recall Identification Labels for IPC dealers can be obtained from your Regional Marketing Office.

RECALL IDENTIFICATION LABEL - For CANADA

Place a Recall Identification Label on each vehicle corrected in accordance with the instructions outlined in this Product Recall Bulletin. Each label
provides a space to include the recall number and the five (5) digit dealer code of the dealer performing the recall service. This information may be
inserted with a typewriter or a ball point pen.

Put the Recall Identification Label on a clean and dry surface of the radiator core support in an area that will be visible to people servicing the
vehicle. Additional Recall Identification Labels for Canadian dealers can be obtained from DGN by calling 1-800-668-5539 (Monday - Friday,
8:00 a.m. to 5:00 p.m. EST). Ask for Item Number GMP 91 when ordering.

COURTESY TRANSPORTATION - U.S. AND CANADA ONLY

The availability of a loaner/rental vehicle to customers whose vehicles are involved in this recall is of the utmost importance in maintaining
customer satisfaction. If requested, please ensure that these customers have the opportunity to use a loaner/rental vehicle for one day at no charge
while their vehicle is being serviced. One day is defined as a 24-hour period and the maximum allowance for the loaner/rental vehicle is $30.00
(U.S.), $40.00 (Canada). Please make sure that required parts are available at your dealership prior to scheduling service appointments for these
customers.

CLAIM INFORMATION
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 45
Chevrolet Venture V6-3.4L VIN E 2370

Submit a Product Recall Claim with the information as shown.

Refer to the General Motors WINS Claims Processing Manual for details on Product Recall Claim Submission.

CUSTOMER NOTIFICATION - For US and CANADA

Customers will be notified of this recall on their vehicles by General Motors (see copy of customer letter shown in this bulletin.

CUSTOMER NOTIFICATION - For IPC

Letters will be sent to known owners of record located within areas covered by the US National Traffic and Motor Vehicle Safety Act. For owners
outside these areas, dealers should notify customers using the suggested dealer letter shown.

DEALER RECALL RESPONSIBILITY - For US and IPC (US States, Territories, and Possessions)

The US National Traffic and Motor Vehicle Safety Act provides that each vehicle that is subject to a recall of this type must be adequately repaired
within a reasonable time after the customer has tendered it for repair. A failure to repair within sixty days after tender of a vehicle is prima facie
evidence of failure to repair within a reasonable time. If the condition is not adequately repaired within a reasonable time, the customer may be
entitled to an identical or reasonably equivalent vehicle at no charge or to a refund of the purchase price less a reasonable allowance for
depreciation. To avoid having to provide these burdensome remedies, every effort must be made to promptly schedule an appointment with each
customer and to repair their vehicle as soon as possible. In the recall notification letters, customers are told how to contact the US National
Highway Traffic Safety Administration if the recall is not completed within a reasonable time.

DEALER RECALL RESPONSIBILITY - ALL

All unsold new vehicles in dealers' possession and subject to this recall must be held and inspected/repaired per the service procedure of this recall
bulletin before customers take possession of these vehicles.

Dealers are to service all vehicles subject to this recall at no charge to customers, regardless of mileage, age of vehicle, or ownership, from this time
forward.

Customers who have recently purchased vehicles sold from your vehicle inventory, and for which there is no customer information indicated on the
dealer listing, are to be contacted by the dealer. Arrangements are to be made to make the required correction according to the instructions
contained in this bulletin. This could be done by mailing to such customers, a copy of the customer letter shown in this bulletin. Recall follow-up
cards should not be used for this purpose, since the customer may not as yet have received the notification letter.

In summary, whenever a vehicle subject to this recall enters your vehicle inventory, or is in your dealership for service in the future, you must take
the steps necessary to be sure the recall correction has been made before selling or releasing the vehicle.
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 46
Chevrolet Venture V6-3.4L VIN E 2371

DISCLAIMER
Important Information
IMPORTANT:
The service procedure contained in this recall is different from the service procedure found in the appropriate service manual. As a result, the
labor time allowance has been revised to correspond with this new service procedure. In the near future the service manual and labor time guide
will be updated with this new information.

Inspection Process
(Right side shown, Left side similar)

1. Remove the garnish at the top of the door trim panel.

2. Remove the inside door handle using J-42506.

3. Remove the door trim panel.

4. Partially remove the water deflector.

5. Remove the bolts (three) from the lock plate.

6. With light pressure push outward on the latch plate and look through the hole in the inner panel. See arrow in figure 1.

7. Inspect the actuator date code located directly below the part number on the side of the actuator, to determine if actuator replacement is
needed. The date code consists of three parts:

^ Juan date: example: 118 = the 118th day of the calendar year (i.e. April 28, 2001)

^ Calendar Year: example: 01 = 2001, 00 = 2000

^ Production Shift example: A = 1st shift: B = 2nd shift

If the date code is 118-01-A or greater, replacement is not required. If the date code is 117-01-A or less (including any date code with 00" for
calendar year), replace the actuator. If replacement is required, follow the Replacement Procedure.

8. If replacement is not required, torque the bolts to the lock plate following the torque sequence to 10 Nm (89 lb. in.). See step 13 and figure 6
of Replacement Procedure.

9. Reinstall the water deflector.

10. Remove and replace the thirteen trim panel fasteners.

11. Reinstall the door trim panel.

12. Reinstall the garnish molding at the top of the door trim panel.
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 47
Chevrolet Venture V6-3.4L VIN E 2372

13. Install the GM Recall Identification Label.

Replacement Procedure
(Right side shown, Left side similar)

1 Remove the electrical connectors from the actuators. Refer to (1) in figure 2.

2. Remove the lock rod from the latch plate assembly. Refer to (2) in figure 2.

3. Disconnect the lock rod from the center of the door so the rod can be moved to the side. Refer to (2) in figure 2.

4. Remove the bolts (four) from the latch.

5. Rotate the latch plate counter clockwise slightly and rearward to remove the latch plate.

6. Remove the outside handle cable from the latch plate.

7. Drill the rivets from the actuator. Refer to arrows in figure 3.

8 Replace the rivets in the same direction as they were removed. See figure 4.

9. Replace the lock rod retainer.

10. Install the outside cable to the latch plate.

11. Reinstall the latch plate and hand tighten the bolts.
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 48
Chevrolet Venture V6-3.4L VIN E 2373

12. Torque the bolts to the latch following the torque sequence to 10 Nm (89 lb. in.). See figure 5.

13. Torque the bolts to the lock plate following the torque sequence to 10 Nm (89 lb. in.). See figure 6.

14. Reinstall the lock rod to the lock plate and the lock rod retainer.

15. Reinstall the electrical connectors.

16. Important: Before the door trim is reinstalled close the latch at the rear of the door with a screwdriver. Look through the small oval hole just
above the door handle and rotate the door handle rearward. Just before the lever gets to the stop (see arrow in figure 7) the latch should open.
If the latch does not open, a slight bend to shorten the rod (see arrows in figure 8) will be necessary.

17. Reinstall the water deflector.

18. Remove and replace the thirteen trim panel fasteners.

19. Reinstall the door trim panel.

20. Reinstall the garnish molding at the top of the door trim panel.

21. Install the GM Recall Identification Label.


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 49
Chevrolet Venture V6-3.4L VIN E 2374
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 50
Chevrolet Venture V6-3.4L VIN E 2375
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 51
Chevrolet Venture V6-3.4L VIN E 2376
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 52
Chevrolet Venture V6-3.4L VIN E 2377
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 53
Chevrolet Venture V6-3.4L VIN E 2378
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 54
Chevrolet Venture V6-3.4L VIN E 2379
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 55
Chevrolet Venture V6-3.4L VIN E 2380

Technical Service Bulletin # 00-08-64-015A Date: 010201

Power Sliding Side Door - Edge Guard Comes Loose


File In Section: 08 - Body and Accessories

Bulletin No.: 00-08-64-015A

Date: February 2001

TECHNICAL

Subject:
Power Sliding Side Door Edge Guard Comes Loose
(Install New Edge Guard)

Models:
1997-2000 Chevrolet Venture
1997-2000 Oldsmobile Silhouette
1997-1999 Pontiac Trans Sport
1999-2000 Pontiac Montana

This bulletin is being revised to update parts information. Please discard Corporate Bulletin Number 00-08-64-015 (Section 08 - Body &
Accessories).

Condition

Some customers may comment that the door edge guard has started to come oft or the over-slam bumper has fallen off.

Cause

A loss of adhesion to the body may have occurred.

Correction
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 56
Chevrolet Venture V6-3.4L VIN E 2381

1. If the over-slam bumper is missing, clean the surface of the door and install the bumper just below the body feature line (see Figure).

2. Install the new door edge guard just below the over-slam bumper. The new door edge guard pushes over the hem flange on the front leading
edge of the door (see Figure).

Parts Information

Parts are currently available from GMSPO.

Warranty Information

For vehicles repaired under warranty, use the table.

DisclaimerTechnical Service Bulletin # 00-01-38-001 Date: 000101

A/C - Lack of Performance in Hot/Humid Weather


BULLETIN NUMBER:
00-01-38-001

SECTION:
01 - HVAC

DATE:
January, 2000

TITLE:
HVAC Lack of Performance - Single A/C System Only (Evacuate & Recharge A/C System)

MODELS:
1998-2000 Chevrolet Venture
1998-2000 Oldsmobile Silhouette
1998-2000 Pontiac Trans Sport
With C60 Air Conditioner Frt, Manual Controls (Not C34)
Built from SOP thru VIN Breakpoint YD150489 for 2000 Models Only

CONDITION:
Some customers may comment on a lack of performance of the air conditioning system in hot, humid weather.

CAUSE:
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 57
Chevrolet Venture V6-3.4L VIN E 2382
This condition may be due to an undercharged air conditioning system during the vehicle assembly process.

CORRECTION:
1. Perform the Cooling Insufficient, A/C System check. Refer to the HVAC Systems-Manual sub-section of the Service Manual. If a condition
is identified, make the appropriate repair. If no abnormal condition is identified, proceed to the next step.

2. Evacuate and recharge the A/C system with 1.08 kg (2.375 lbs) of R-134a.

3. Replace the A/C evaporator label with P/N 10443319. This label will allow future service technicians to know how much refrigerant is
required by the system.

4. Inspect/test the A/C system for signs of leaks, both visually and with the A/C leak tester.

5. If a leak is found, perform the recommended repair. Refer to the HVAC Systems-Manual sub-section of the Service Manual.

6. If no leaks are found, perform the Cooling Insufficient, A/C System check. Refer to the HVAC Systems-Manual sub-section of the Service
Manual. If a condition is identified, make the appropriate repair. If no abnormal condition is identified, return the vehicle to the owner.

PARTS INFORMATION

Parts are currently available from GMSPO.

WARRANTY INFORMATION

For vehicles repaired under warranty, use chart:

*The 0.6 hr includes the time required to install the new label.

If an evacuate and recharge was required, add 0.9 hr to the base time for evacuating and recharging the HVAC System.

This is a unique Labor Operation Number for use only with this bulletin. This number will not be published in the Labor Time Guide.

Technical Service Bulletin # 01-03-10-009A Date: 040727

Wheels - Plastic Wheel Nut Covers Loose/Missing


Bulletin No.: 01-03-10-009A

Date: July 27, 2004

TECHNICAL

Subject:
Plastic Wheel Nut Covers Missing and/or Loose (Replace Missing Covers and Add Sealant to All Covers)

Models:
2005 and All Prior Passenger Cars (Except All Cadillac Models and Pontiac GTO)

with Plastic Wheel Nut Covers

Supercede:

This bulletin is being revised to add additional models years. Please discard Corporate Bulletin Number 01-03-10-009.

Condition

Some customers may comment that the plastic wheel nut covers are missing and/or loose.

Correction

Important:
^ DO NOT USE a silicone-based adhesive.
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 58
Chevrolet Venture V6-3.4L VIN E 2383

^ Do not apply the *permatex(R) around the threads in a circular pattern.

^ Apply a single bead across the threads approximately 10 mm (0.4 in) in length, 5 mm (0.2 in) in height and 5 mm (0.2 in) in width.

Replace any missing plastic wheel nut covers with the appropriate covers and apply Permatex(R) # 2 Form A Gasket Sealant(R) to the threads of all
the plastic wheel nut covers. Tighten finger tight plus a 1/4 turn with a hand wrench.

*We believe this source and their products to be reliable. There may be additional manufacturers of such material.

General Motors does not endorse, indicate any preference for or assume any responsibility for the products from this firm or for any other such
items which may be available from other sources.

Permatex(R) # 2 Form A Gasket Sealant(R) part numbers (available at your local parts supplier)

^ P/N 80009 (2A/2AR) - 44 ml (1.5 oz) tube boxed


^ P/N 80015 (2AR) - 44 ml (1.5 oz) tube carded
^ P/N 80010 (2B/2BR) - 89 ml (3 oz) tube boxed
^ P/N 80016 (2BR) - 89 ml (3 oz) tube carded
^ P/N 80011 (2C) - 325 ml (11 oz) tube boxed

Warranty Information

For vehicles repaired under warranty, use the table.

Disclaimer
Technical Service Bulletin # 00-08-64-007 Date: 000601

Front Door Window - Inoperative/Slow or Noisy


File In Section: 08 Body and Accessories

Bulletin No.: 00-08-64-007

Date: June, 2000

TECHNICAL

Subject:
Slow/Non-Moving (Chatters/Noisy) Glass, Bent Regulator Arms or Window is inoperative (Replace Run Channel and/or Weatherstrip)

Models:
1997-2000 Chevrolet Venture
1997-2000 Oldsmobile Silhouette
1997-1999 Pontiac Trans Sport
1999-2000 Pontiac Montana

Condition

Some customers may comment that the front door glass is slow or noisy when moving up or down or the window is inoperative.

Cause
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 59
Chevrolet Venture V6-3.4L VIN E 2384

The window run channel may be adjusted improperly which may cause the following:

^ The glass may be slow/non-moving.

^ The glass wears through the flocking on the weatherstrip and allows direct contact between the glass and the rubber of the weatherstrip, which
causes drag.

^ Bent regulator arms may be due to glass drag from the run window channel.

Correction

Adjust the window run channel upper attachment full forward and the lower attachment full rearward. Replace run channel and/or weatherstrip, if
necessary.

Parts Information

Parts are expected to be available from GMSPO, 6/5/00.

Warranty Information

For vehicles repaired under warranty, use the table.

Disclaimer
Procedure
1. Remove the door switch plate.

2. Disconnect the electrical connectors from the switch plate.

3. Remove the bezel behind the door handle.

4. Remove the bolts from the armrest.

5. Remove the trim panel retainers and remove the trim panel.

6. Remove the water deflector.

7. Remove the inner belt seal.

8. Remove the outer belt seal.

9. Raise the glass to gain access to the lower sash channel retaining clips. Push in on the retainers and slide the sash channel to release the glass.
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 60
Chevrolet Venture V6-3.4L VIN E 2385

10. Remove the glass from the door.

11. Remove the weatherstrip from the run channel.

12. Remove the bolts from the run channel and remove the run channel from the door.

13. Loosen the mirror for weatherstrip removal.

14. Remove the weatherstrip from the door.

15. Spray the backside of the new weatherstrip with window cleaner for ease of installation and install the weatherstrip.

16. Tighten the mirror retaining nuts.

Tighten
Tighten the nuts to 10 Nm (89 lb in).

17. Install the window run channel in the door and leave the retaining bolts finger tight.

18. With the window run channel installed, move the upper attachment full forward and the lower attachment full rearward.

Tighten
Tighten to 10 Nm (89 lb in).

19. Install the weatherstrip in the window lower run channel.

20. Install the glass door.

21. Install the outer belt seal.

22. Install the inner belt seal.

23. Install the water deflector using a 50.8 mm (2 in) wallpaper roller. Starting at the bottom center and working outboard, roll out the butyle
adhesive up the right and left sides. A 50.8 mm (2 in) roller can be purchased at a hardware or wallpaper store.

24. Install the trim panel.

25. Install the door trim panel bolts. Tighten

Tighten the bolts to 3 Nm (26 lb in).

26. Attach the electrical connectors to the switch and install the switch.

27. Install the door handle bezel.Technical Service Bulletin # 01-08-57-006 Date: 011101

Body/Frame - Mildew Odor, Water Leaks


File In Section: 08 - Body and Accessories

Bulletin No.: 01-08-57-006

Date: November, 2001

TECHNICAL

Subject:
General Waterleak Diagnosis Guide

Models:

1997-1999 Buick GL8 (Export China)


1997-1999 Chevrolet Trans Sport (Export Europe)
1997-2002 Chevrolet Venture
1997-2002 Oldsmobile Silhouette
1997-2002 Pontiac Trans Sport/Montana
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 61
Chevrolet Venture V6-3.4L VIN E 2386

This bulletin contains information on various waterleak conditions. Refer to the following table for a quick reference to the various conditions and
the corresponding illustrations.

Condition 1

Some customers may comment on a mildew odor or that the front floor is wet.

Cause

The water deflector may not be seated properly to the door sheet metal.

Correction

Seat the water deflector to the door surface at the primary locations. Refer to the arrows in the illustration. If the adhesive surface is dirty and the
water deflector needs to be replaced, follow the procedure listed below.

Service Procedure

1. The adhesive surface must be clean, dry and free of dirt or contaminants. Clean the door surface (around the perimeter of the water deflector)
with one of the cleaners listed below, or an equivalent.

2. Install the water deflector to the inner panel.

3. Pull the harness connectors through their respective holes or slits.

4. Position the outer perimeter of the deflector to the door inner panel by working from the bottom center outboard. Make sure the butyl
adhesive is below the drain holes.

5. Using a 50 mm (2 in) wallpaper roller, roll out the butyl adhesive. Start at the bottom center and work outboard, up the right and left sides. A
50 mm (2 in) roller can be purchased at a hardware or wallpaper store.

Condition 2

Some customers may comment on a mildew odor or that the front floor is wet.

Cause

There may be a void in the seam sealer at the front of dash.

Correction
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 62
Chevrolet Venture V6-3.4L VIN E 2387

1. Run water over the strut tower. Refer to the arrow in the illustration.

2. Inspect the seam on the inside of the vehicle. Refer to the highlighted line in the illustration.

3. Clean the area with one of the cleaners listed below.

4. Seal the voids with seam sealer. Refer to the list below.

Condition 3

Some customers may comment on a mildew odor or that the front floor is wet.

Cause

The wire harness, cables or the HVAC drain that passes through the front of dash may not be sealed properly. Refer to the arrows in the above
illustration.

Correction

Locate the leak by running water down the front of the dash under the hood. Clean the area with one of the cleaners listed below. Seal the area with
a seam sealer listed below.
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 63
Chevrolet Venture V6-3.4L VIN E 2388

Condition 4

Some customers may comment on water dripping from the top of the windshield.

Cause

Important:
A large amount water may be able to enter the vehicle through small holes in the body seam sealer.

^ To check for a void in the windshield urethane, run LOW pressure water under the windshield surround molding.

^ If no leak is present, water may be entering from a hole in the body seam sealer at the "C" pillar and then running forward to the windshield.
Refer to the arrow in the illustration above. Remove the pitch molding, inspect the patch sealers (from "C" pillar to "D" pillar) for holes, folds,
or mis-application. Also, inspect the sheet metal at the top corner of the "C" pillar for holes or visible folds.

Correction

1. The affected surface must be clean, dry and free of dirt or contaminants. Clean the surface with one of the cleaners listed below, or an
equivalent.

2. Fill the pin hole(s) with a clean seam sealer.

Condition 5

Some customers may comment on a mildew odor or that the front floor/mid-floor is wet.

Cause
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 64
Chevrolet Venture V6-3.4L VIN E 2389

There may be a void in the butyl tape/sealer on the hem flange under the auxiliary seal. Refer to the highlighted line in the illustration above.

Correction

1. Clean the flange and weatherstrip with one of the cleaners listed below.

2. Apply some weatherstrip adhesive in the weatherstrip retaining cavity and reinstall the weatherstrip to the hem flange.

Condition 6

Some customers may comment on a mildew odor or the that the mid-floor is wet.

Cause

The "C" pillar may have a sealer void. Refer to the shaded area in the illustration above.

Correction

Clean the area with one of the cleaners listed below and seal with a seam sealer listed below.

Condition 7

Some customers may comment on water pooling up in the corner of the weatherstrip or that the mid-floor is wet.

Cause
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 65
Chevrolet Venture V6-3.4L VIN E 2390

The weatherstrip may allow water to wick in and pool up in the corner. Refer to the arrow in the illustration above.

Correction

Drill a small 3 mm (1/8 in) hole in the interior surface of the weatherstrip. This will allow the water to drain inside the weatherstrip and exit out the
existing holes in the outside of the weatherstrip.

Condition 8

Some customers may comment on clean water in the jack compartment.

Cause

The power sliding side door cable pass-through grommets may not be seated properly. Refer to the locations shown in the illustration above.

Correction

Make sure the power sliding side door grommets are seated properly. Seal the perimeter with weatherstrip adhesive as necessary.

Condition 9

Some customers may comment on dirty water in the jack compartment.

Cause
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 66
Chevrolet Venture V6-3.4L VIN E 2391

There may be a poor seal in the wheelhouse inner to outer sheet metal. Water is thrown off the wheels and forced up through the unsealed joint.
Refer to the illustration above.

Correction

Important:
Wear safety glasses and use compressed air to dry the area.

1. Clean the surface area with one of the cleaners listed below.

2. Seal the hole with one of the sealers listed below.

Condition 10

Some customers may comment on dirty water in the jack compartment.

Cause

There may be a void in the sealer between the inner and outer wheel house liner. Refer to the highlight in the illustration above.

Correction

Important:
Wear safety glasses and use compressed air to dry the area.

Clean the surface area with one of the cleaners listed below and then seal the hole with one of the sealers listed below.

Condition 11

Some customers may comment on wet carpet at the rear of the vehicle.

Cause
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 67
Chevrolet Venture V6-3.4L VIN E 2392

The weatherstrip may be turned in on the sides causing poor contact to the liftgate surface. Refer to the arrow in illustration above.

Correction

1. Remove the weatherstrip from the hem flange.

2. Bend the hem flange outboard to ensure a better seal contact.

Condition 12

Some customers may comment on wet carpet at the rear of the vehicle.

Cause

The weatherstrip may be turned down at the top causing poor contact to the liftgate surface. Refer to the illustration above.

Correction

Bend the hem flange upright to ensure a better seal.

Condition 13

Some customers may comment on wet carpet at the rear of the vehicle.

Cause
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 68
Chevrolet Venture V6-3.4L VIN E 2393

The taillight grommet may not be sealed. Refer to the illustration above.

Correction

Make sure the butyl tape is in place over the taillight grommet.

Condition 14

Some customers may comment that the headliner is wet at the rear of the vehicle.

Cause

The wire harness grommet may not be fully seated. Refer to the illustration above.

Correction

1. Fully seat the rubber grommet.

2. Seal the grommet, if necessary, with weatherstrip adhesive listed below.

Weatherstrip Adhesive

GM Weatherstrip Adhesive Gel (Black), P/N 12345097 (in Canada, use P/N 10953479)

Parts are currently available from GMSPO.

Cleaning Solvents

^ 3M(R) General Purpose Adhesive Cleaner, P/N 08984

^ Dominion Sure Seal, Sure Solve Stock BSS

^ Kent Acrosol(TM)

Seam Sealer

^ 3M(R) Clear Auto Sealer, P/N 08551

^ Kent High Tech Seam Sealer Clear, P/N 10200


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 69
Chevrolet Venture V6-3.4L VIN E 2394

^ Dominion Sure Seal Heavy Duty Drip Check LSC, Item # 9019

DisclaimerTechnical Service Bulletin # 01-05-23-011A Date: 020201

Brakes - Rattling Noise


File In Section: 05 - Brakes

Bulletin No.: 01-05-23-O11A

Date: February, 2002

TECHNICAL

Subject:
Rattle Type Noise Coming from Front of Vehicle
(Install Front Brake Caliper Service Kit)

Models:

2000-01 Buick Century, Regal


2000-01 Chevrolet Impala, Monte Carlo, Venture
2000-01 Oldsmobile Intrigue, Silhouette
2000-01 Pontiac Grand Prix, Montana

This bulletin is being revised to remove Chevrolet Lumina from the Models section and to update the condition information. Please discard
Corporate Bulletin Number 01-05-23-11 (Section 05 - Brakes).

Built Prior to the VIN Breakpoints shown.

Condition

Some customers may comment about a rattle type noise coming from the front of the vehicle. This noise usually occurs at vehicle speeds under 48
km/h (30 mph) and while driving over bumps. The noise can usually be eliminated by a light application of the brake pedal.

Cause

This condition may be caused by too much clearance between the front brake caliper bracket and the caliper pins in the bottom of the bracket bores.

Correction

Install front brake caliper service kits to both sides of the vehicle using the following service procedure. Each kit contains 2 pins, 2 boots, and 2
packets of grease.

Service Procedure

1. Raise and suitably support the vehicle. Refer to Lifting and Jacking the Vehicle in General Information.

2. Remove both the front tire and wheel assemblies.

3. Hand tighten 2 wheel nuts to retain the rotor to the hub.


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 70
Chevrolet Venture V6-3.4L VIN E 2395

4. Install a large C-clamp (2) over the top of the brake caliper and against the back of the outboard brake pad.

5. Tighten the C-clamp until the caliper piston is pushed into the caliper bore enough to slide the caliper off the rotor.

6. Remove the C-clamp from the caliper.

7. Remove the caliper pin bolts (3) and discard. New bolts are supplied with the service kit.

8. Remove the caliper (1) from the caliper bracket (2) and support the caliper with heavy mechanic's wire, or equivalent.

9. Using a flat bladed tool or punch, carefully tap the caliper pin boots from the brake caliper bracket and discard.

10. Remove and discard the bushings from the brake caliper bracket bores. Carefully insert a small screwdriver into the brake caliper bracket
bore, then rotate and pull the bushing outward to remove.

11. Remove the brake pads from the brake caliper bracket.

12. Thoroughly clean the brake caliper bracket bores of all lubricant.

13. Install the brake pads to the brake caliper bracket.

14. Lubricate the brake caliper bracket bores. Divide the large packet of grease, P/N 18046532; put one-half packet into each bore.
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 71
Chevrolet Venture V6-3.4L VIN E 2396

15. Lubricate the new caliper pin boots. Use the small packet of grease, P/N 18046645, only on the bottom internal threads (2).

16. Install the new caliper pin boots into the caliper pin bores (3) on the bracket. Carefully tap boots into bores using a deep well socket or
equivalent.

17. Install the caliper over the rotor and onto the caliper bracket. Ensure that the caliper pin boots are not pinched.

Important:
The leading caliper pin, or top pin, has a bushing as part of the assembly. The trailing caliper pin, or bottom pin, is a solid design.

18. Install the new caliper pin bolts (1). It is important to note which caliper pin is designed for the correct bore. The leading caliper pin, or top
pin, has a bushing as part of the assembly. The trailing caliper pin, or bottom pin, is a solid design. Ensure that the bolt boots fit securely in
the groove of the pin bolts. Be sure not to pinch or tear the boots. If the boots are damaged, they must be replaced.

Tighten

Tighten the bolts to 95 N.m (70 lb ft).

19. Remove the 2 wheel nuts retaining the rotor to the hub.

20. Repeat the above steps for the other side.

21. Install both the front tire and wheel assemblies. Tighten the wheel nuts using the J 39544 kit.

22. Lower the vehicle.

Parts Information
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 72
Chevrolet Venture V6-3.4L VIN E 2397

Parts are currently available from GMSPO.

Warranty Information

For vehicles repaired under warranty, use the table.

DisclaimerTechnical Service Bulletin # 01-06-03-005 Date: 010501

Interior/Exterior Lamps - Flicker


File In Section: 06 - Engine/Propulsion System

Bulletin No.: 01-06-03-005

Date: May, 2001

TECHNICAL

Subject:
Interior and Exterior Lamps Vary in Brightness
(Replace Generator Voltage Regulator Ground Screw)

Models:

2000-2001 Chevrolet Impala (With 3800 Engine and Police or Taxi Package)
2000-2001 Chevrolet Venture
2000-2001 Oldsmobile Silhouette
2000-2001 Pontiac Montana

Condition

Some customers may comment that the interior and/or the exterior lamps vary in intensity (flicker).

Correction
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 73
Chevrolet Venture V6-3.4L VIN E 2398

Replace the voltage regulator attaching screw with the screw and washer from the service kit following the procedure outlined.

1. Disconnect the battery cable.

2. Remove the wiper module cover (U-Van).

3. Remove the voltage regulator ground screw (1). (This is the recessed screw located 1/3 of the way from the large battery cable attachment to
the generator harness.) Use a stubby # 2 Phillips screwdriver to break it loose and then loosen the screw with a small pocket screwdriver. The
screw may hang up on the plastic cover on the rear of the generator. If this happens, use a pocket screwdriver inserted between the screw and
the cover. The screw will pop out when a little sideways pressure is applied.

4. Install the screw and washer from the kit through the voltage regulator and into the generator case.

5. Tighten the screw securely.

6. Replace the wiper module cover.

7. Reconnect the battery cable.

Tighten

Tighten the cable to 15 N.m (11 lb ft).

Parts Information

Parts are expected to be available from GMSPO, 5/16/01.

Warranty Information

For vehicles repaired under warranty, use the table.


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 74
Chevrolet Venture V6-3.4L VIN E 2399

DisclaimerTechnical Service Bulletin # 02-08-58-003 Date: 020601

Interior - Road Noise Heard From Behind Front Seats


File In Section: 08 - Body and Accessories

Bulletin No.: 02-08-58-003

Date: June, 2002

TECHNICAL

Subject:
Road Noise Heard Behind Front Seats (Seal Sheet Metal Seams)

Models:
1997-2002 Chevrolet Venture
1997-2002 Oldsmobile Silhouette
1997-2002 Pontiac TransSport, Montana

Condition

Some customers may comment that road noise can be heard coming from the area behind the front seats.

Cause

This condition may be caused by an open sheet metal seam in the metal support panel between the frame rail and the rocker panel.

Correction

1. Raise the vehicle on a hoist. Refer to Lifting and Jacking the Vehicle in the General Information Subsection of the Service Manual.

2. Locate the support panel between the underbody frame rail and the rocker panel. It is in the middle of the underbody of the vehicle just
behind the front doors. The support panels on both sides of the vehicle must be sealed.

3. Clean both the front and back sides of the support panel as required.
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 75
Chevrolet Venture V6-3.4L VIN E 2400

4. Apply Medium Body Seam Sealing Compound, P/N 12378500 (in Canada, P/N 10952233), to the front side of the support panel at the
locations shown by the arrows in the illustration. Use a small brush to force the sealer into the open seams and corners of the support panel.

5. Apply Medium Body Seam Sealing Compound, P/N 12378500 (in Canada, P/N 10952233), to the rear side of the support panel at the
locations shown by the arrows in the illustration. Use a small brush to work the sealer into the open seams and corners of the support panel.

6. Lower the vehicle


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 76
Chevrolet Venture V6-3.4L VIN E 2401

Parts Information

Parts are currently available from GMSPO.

Warranty Information

For vehicles repaired under warranty, use the table.

DISCLAIMER
Technical Service Bulletin # 02-08-67-006B Date: 030301

Body - Front/Rear Roof Rust Perforation


File In Section: 08 - Body and Accessories

Bulletin No.: 02-08-67-006B

Date: March, 2003

TECHNICAL

Subject:
Roof Perforation (Replace Roof)

Models:
1997-2003 Chevrolet Venture
1997-2003 Oldsmobile Silhouette
1997-2003 Pontiac TranSport/Montana

This bulletin is being revised to add another condition in the Labor Operation Warranty Table. Please discard Corporate Bulletin Number
02-08-67-006A (Section 08 - Body and Accessories).

Important:
Implementation of this service bulletin by "GM of Canada" dealers requires prior District Service Manager approval.

Condition

Some customers may comment that there is rust forming around the front or rear portion of the roof.

Cause

During production, the E-coating (ELPO primer) may have been missed in concealed areas of the front or rear portions of the outer roof panel.

Correction

Important:
Partial repairs to the roof panel are not permitted.

1. Remove the headliner. Refer to Headliner Replacement in the Interior Trim subsection of the Service Manual (SI document ID # 508247).
This document ID can only be found under 2003; however, this procedure covers 1997-2002 also.

2. Replace the roof. Refer to Roof Outer Replacement in the Collision Repair subsection of the Service Manual (SI document ID # 875050).
This document ID can only be found under 2003; however, this procedure covers 1997-2002 also.
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 77
Chevrolet Venture V6-3.4L VIN E 2402

Important:
Adhesive Bonding is the preferred installation method.

3. Reinstall the headliner. Refer to Headliner Replacement in the Interior Trim subsection of the Service Manual.

Parts Information

Parts are currently available from GMSPO.

Warranty Information

For vehicles repaired under warranty, use the table shown.

Disclaimer
Technical Service Bulletin # 02-08-58-005B Date: 050209

Body - Wind Noise From Windshield Base


Bulletin No.: 02-08-58-005B

Date: February 09, 2005

TECHNICAL

Subject:

Windnoise At Base Of Windshield (Seal Sheet Metal Seams)

Models:
2005 Buick Terraza
1997-2005 Chevrolet Venture
2005 Chevrolet Uplander
1997-2004 Oldsmobile Silhouette
1997-2004 Pontiac TransSport, Montana
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 78
Chevrolet Venture V6-3.4L VIN E 2403
2005 Pontiac Montana SV6
2005 Saturn Relay

Supercede:

This bulletin is being revised to add model years and models. Please discard Corporate Bulletin Number 02-08-58-005A (Section 08 - Body and
Accessories).

Condition

Some customers may comment on a Windnoise from the base of the windshield (right and/or left side). The concern is most apparent while driving
in a crosswind.

Cause

This condition may be caused by improperly sealed sheet metal seams in the cowl.

Correction

Apply seam sealer to the sheet metal seams just below the lower corners of the windshield.

1. Remove the air inlet grille. Refer to the Air Inlet Grille Panel Replacement procedure in the Body Front End Sub-section of the Service
Manual.

2. Locate the sheet metal seams at the base of the windshield on both sides of the cowl. Refer to the dotted line in the illustration above for the
location. Left side shown. Right side typical.

3. Apply Medium Body Seam Sealing Compound, P/N 12378500 (in Canada, P/N 10952233), or equivalent, as required, to the sheet metal
seams on both sides of the cowl.

4. Reinstall the air inlet grille. Refer to the Air Inlet Grille Panel Replacement procedure in the Body Front End Sub-section of the Service
Manual.

Parts Information
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 79
Chevrolet Venture V6-3.4L VIN E 2404

Parts are currently available from GMSPO.

Warranty Information

For vehicles repaired under warranty, use the table.

Important:
Saturn Retailers Only: Do NOT claim GM P/N 12378500. It will be necessary to sell Medium Body Seam Sealer to the CSO as "material" using
net item code "M". Claims received in the amount of $2.50 for this part will be accepted. Claims exceeding the amount of $2.50 will be returned
with the Return Reason 143 - Material/Reimbursement > Maximum Allowed.

DisclaimerTechnical Service Bulletin # 99-09-41-004 Date: 000101

Air Bag (SIR) On-Off Switch Kits, New Parts and Service
Bulletin Number:
99-09-41-004

Section:
09 - Restraints

Date:
January, 2000

Title:
Frontal Supplemental Inflatable Restraints (SIR) On-Off Switch Kits, New Parts and Procedures

Models:
1988-2000 Passenger Cars and Trucks

This bulletin is being revised to add the 1999 & 2000 model years. Please discard Corporate Bulletin Number 73-90-23 (Section 9 - Accessories).

Never consider installing an air bag on-off switch unless the following conditions are met:

1. The customer presents a letter from NHTSA authorizing the installation of the air bag on-off switch.

2. The dealership gives the customer a copy of the NOTICE TO GM OWNERS ABOUT AIR BAG ON-OFF SWITCHES.

3. The customer still wants the air bag on-off switch installed.

This bulletin includes information regarding switches to turn off and on frontal air bags, additional switch/display light diagnosis, switch
installation kit content descriptions and ordering directions for special pants (if required).

Some time ago, the National Highway Traffic and Safety Administration (NHTSA) announced a new regulation about air bags. The new regulation
includes procedures that will permit the installation of air bag on-off switches for the few customers who, in NHTSA's opinion, fit the criteria for
switches.

Important:
Due to the new regulation, DEALERS SHOULD NO LONGER USE THE INFORMATION ON AIR BAG DISCONNECTION (Corporate
Bulletin # 73-90-12, dated June, 1997). INSTEAD, USE THE INFORMATION INCLUDED WITH THIS BULLETIN.

The switch installation kit contains the necessary components (switch, bracket, attaching hardware, display light, applique, sheet for switch and
light, tie straps and instruction sheets) for system operation.
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 80
Chevrolet Venture V6-3.4L VIN E 2405

Some kits also include a replacement safety belt for certain vehicles that are designed with specific FORCE LIMITING safety belt systems. Special
Owner's Manual inserts are included in the installation kit for system operation review by the owner.

Additional equipment such as a 12 volt test lamp and the J 38125-B (-A or -500 will also apply) Terminal Repair Kit, are required to complete the
switch kit installation. In some cases, scan tools (Tech II or equivalent) may be required to reprogram certain control modules.

The cost of the switch kit and labor to install the switch kit are the responsibility of the customer. Suggested times for installation are in the
illustration.

Important:
In rare instances, the installation of switch(es) may turn on the vehicle air bag warning light. This condition may exist due to the additional
resistance of the switch and harness when added to the SIR system. In these rare instances, a SPECIAL SERVICE ONLY Diagnostic Energy
Reserve Module (DERM) of Sensing and Diagnostic Module (SDM) will be made available to the owner from GMSPO at no charge for the
parts and labor. Prior to ordering and/or installing a switch kit, the customer should be advised that this potential does exist and can be resolved
by one of the following options:

If the light does come on after switch installation (AND PROPER INSTALLATION AND CONNECTIONS HAVE BEEN VERIFIED), advise the
customer that the light has come on and that the vehicle:

^ May be driven with the light on until the special DERM or SDM is available. The switch portion to turn off the air bag will still function
properly, but the warning light will be on until the additional part can be obtained. When the DERM or 5
SDM is available, the customer should return to have the part installed (at no cost to the customer) OR

^ May have the existing air bag system reconnected and leave the switch (inoperative) in the vehicle until the additional part can be obtained.
When the DERM or SDM is available, the customer should return to have the part installed (at no cost to the customer).

The standard SIR system diagnosis can be made by disconnecting the switch from the SIR wiring harness and following the directions for SIR
System Diagnosis found in the appropriate Service Manual.
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 81
Chevrolet Venture V6-3.4L VIN E 2406

A description of the major components of the installation kit is as follows:

SWITCHES

One switch kit will be required for each air bag (driver or passenger) and will be ignition key operated. When the switch is in the OFF position, the
air bag will remain OFF until the switch is turned to the ON position. Turning the switch to the ON position will allow the air bag to function.

The recommended locations for the switches on most vehicles is in the instrument panel glove compartment (center console if vehicle has no glove
compartment) or, in the case of some vans, in the center stowage compartment (see the recommended location illustrations that are provided with
each switch kit).

Important:
Switches or display light indicators MUST NOT be placed on any instrument panel surfaces directly in front of the driver's or passenger's leg or
knee areas.

DISPLAY LIGHT

Each switch requires a display light to indicate the OFF status of the air bag. Each display light includes a harness to be connected to the switch
harness. The recommended mounting locations for the display lights vary, but are typically located at the center front edge of the roof headliner (or
windshield garnish molding) above the rear view mirror (see the recommended location illustrations provided with each switch kit).

Important:
When installed, driver and/or passenger display light(s) must be visible by all front seat occupants.

Important:
Switches or display light indicators MUST NOT be placed on any instrument panel surfaces directly in front of the driver's or passenger's leg or
knee areas.

WIRING CONNECTIONS

In general terms, the switch will be connected IN SERIES with the appropriate air bag (at the service disconnect) and will require additional
connection of a feed wire to an ignition fed circuit and a ground wire to the body to complete the circuit for the display light indicator.
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 82
Chevrolet Venture V6-3.4L VIN E 2407
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 83
Chevrolet Venture V6-3.4L VIN E 2408

Diagnostics for the switch and display light are included in the illustrations. As always, the technician should make sure to review the wiring
harness routing and installation for pinching, rubbing and chafing to brackets, braces (etc.) and take appropriate actions to protect the wiring from
those potential conditions.

PARTS INFORMATION

Order the appropriate Installation Kit(s) (passenger, driver, or both) from GMSPO. For kit part numbers and usage, see Group 14.865 of the
appropriate GMSPO Parts Catalog.

If special DERMs or SDMs are required to resolve a WARNING LIGHT ON condition, order the part from GMSPO in the normal manner. For
part numbers and usage see Group 14.865 of the appropriate GMSPO Parts Catalog.

Important:
1995-98 G (Aurora and Riviera) and 1997-00 Y (Corvette) switch kits include replacement safety belts. These belts MUST replace the original
safety belts when installing a switch kit. Aurora and Riviera models built on or after January 1,1998 will include DEPOWERED air bags, and
the safety belts on these vehicles will not be included in switch kits and MUST NOT BE CHANGED. The 1997-00 Corvette models will
require safety belt changes regardless of build dates. The belts will be replaced at no charge for the parts or the labor.

WARRANTY INFORMATION

Switch kits and installation are NOT considered a warranty repair. Pans and labor charges (except for special DERM or SDM and replacement
safety belt installation if required) are the responsibility of the customer. If special DERMs or SDMs are required to resolve a WARNING LIGHT
ON condition, USE THE EXISTING LABOR OPERATION AND TIME ALLOWANCES WITH THE SPECIAL CUSTOMER AND FAILURE
CODES WHEN SUBMITTING CLAIMS:

DERMs

USE LABOR OPERATION C8815, CUSTOMER COMPLAINT CODE WK AND FAILURE CODE 93. USE PUBLISHED LABOR
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 84
Chevrolet Venture V6-3.4L VIN E 2409
OPERATION TIMES.

SDMs

USE LABOR OPERATION C8817, CUSTOMER COMPLAINT CODE WK AND FAILURE CODE 93. USE PUBLISHED LABOR
OPERATION TIMES. When installing switch kits on 1995-98 Aurora, Riviera and 1997-00 Corvette models, the appropriate safety belts must be
replaced. When submitting claims, use the existing labor operation and time allowances with special customer complaint and failure codes. The
LABOR ONLY may be claimed. The cost of the belt is included in the kit price.

USE C9040 RIGHT SIDE ONLY, C9041 LEFT SIDE ONLY OR C9047 FOR BOTH AND INCLUDE THE CUSTOMER COMPLAINT CODE
MH AND FAILURE CODE 93 USE PUBLISHED LABOR OPERATION TIMES.

ADMINISTRATIVE INFORMATION

When the dealer decides to install an air bag on-off switch under NHTSA's new regulation, the dealer should fill out and send to NHTSA the form
entitled INSTALLATION OF AIR BAG ON-OFF SWITCHES. The dealer should also keep:

1. A copy of the INSTALLATION form.

2. A copy of the letter NHTSA sent to the customer authorizing the switch.

3. A copy of any waiver the dealer obtains from the customer when the switch is installed.

Important:
In addition, the new regulations require dealers to send the original of the customer's signed authorization form to NHTSA at the following
address:

National Highway Traffic Safety Association


Attention: Air Bag Switch Forms
400 Seventh Street, S.W.
Washington, D.C. 20590-1000
Technical Service Bulletin # 02-09-41-001 Date: 020601

Computers & Controls - DTC's Set When Replacing Modules


File In Section: 09 - Restraints

Bulletin No.: 02-09-41-001

Date: June, 2002

INFORMATION

Subject:
DTCs B1001, B1271 or B1780 Set When Replacing/Reprogramming Other Modules

Models:
1999-2003 Passenger Cars and Trucks
with Class 2 Serial Data Communication Between Modules

This bulletin is being revised to add model years and reflect changes in the Tech 2(R) procedure and filing classification. Please discard Corporate
Bulletin Number 99-06-03-010A (Section 06 - Engine).

Class 2 Serial Data Communication allows control modules (i.e. the Powertrain Control Module (PCM), the Body Control Module (BCM), the
Dash Integration Module (DIM), the Instrument Panel Cluster (IPC), the radio, the Heating, Ventilation and Air Conditioning (HVAC) Controller,
and the Sensing and Diagnostic Module (SDM) to exchange information. This information may be operational information or identification
information. Among the identification information exchanged and compared within these modules is the Vehicle Identification Number (VIN).
Typically the one module, the master module, broadcasts the VIN and all the other modules compare the VIN stored within itself. When the
broadcast VIN does not match the VIN stored within the SDM, the following actions occur:

^ DTC B1001 Option Configuration Error is set and deployment of the airbags is inhibited.

^ DTC B1271 or a DTC B1780 Theft Locked. The VIN information is also used by the radio. When the VIN does not match the VIN stored
within the radio, DTC B1271 or DTC B1780 is set and the radio is inoperative.

Additionally, the master module will compare the SDM's part number (last four digits) to determine if the correct SDM is installed in the vehicle. If
the SDM is the wrong part, a B1001 will also set.

This situation may occur when a vehicle is being repaired. When a PCM or a body control type module is replaced, the VIN information must be
programmed into the replaced (new) control module. A module which has had VIN information entered into it (for example, one taken from
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 85
Chevrolet Venture V6-3.4L VIN E 2410
another vehicle) cannot be reprogrammed. VIN information can only be entered into new modules. The ignition must be ON in order to program
the control module. Since the VIN information is broadcast when the ignition goes to ON from any other ignition switch position, DTCs may be set
in the SDM and/or the radio. Therefore, always follow the specified control module replacement procedures.

1. After completing the repair, turn OFF the ignition for at least 30 seconds.

2. Turn ON the ignition and check for DTCs using a Tech 2(R) scan tool.

If DTCs B1001, B1271, or B1780 are present with a history status, DO NOT REPLACE THE SDM OR THE RADIO.

3. Clear the DTCs from all modules using the Tech 2(R) scan tool.

4. Remove the Tech 2(R) from the vehicle

5. Ensure the proper operation of the SDM by turning OFF the ignition and then turning ON the ignition. The air bag warning indicator should
flash seven times and then go OFF.

Refer to Corporate Bulletin Number 99-09-41-001 for additional information regarding proper reprogramming of the new/replaced module.

Clearing codes from the other modules is part of the replacement and reprogramming procedure for the replaced module. The repair is not complete
unless all codes have been cleared from all modules.

DO NOT SUBMIT CLAIMS FOR OTHER MODULE REPLACEMENTS OR REPROGRAMMING.

DISCLAIMERTechnical Service Bulletin # 02-07-30-022B Date: 031020

A/T - MIL/SES Lamp ON/Multiple A/T DTC's Set


Bulletin No.: 02-07-30-022B

Date: October 20, 2003

TECHNICAL

Subject:

Service Engine Soon (SES) Light On With DTCs P0716 and/or P0717, P0730, P0753, P0758, P1860, P1887, or other Miscellaneous Transmission
Trouble Codes Set (Repair Wiring at Transaxle Wiring Pass-thru Connector)

Models:
2000-2004 Buick Century, LeSabre, Park Avenue, Regal
2003-2004 Buick Rendezvous
2000-2001 Chevrolet Lumina
2000-2004 Chevrolet Cavalier, Impala, Malibu, Monte Carlo, Venture
2004 Chevrolet Classic
2000-2002 Oldsmobile Intrigue
2000-2003 Oldsmobile Aurora
2000-2004 Oldsmobile Alero, Silhouette
2000-2004 Pontiac Bonneville, Grand Am, Grand Prix, Montana, Sunfire
2001-2004 Pontiac Aztek
2000 Toyota Cavalier
with 4T65-E, 4T40-E or 4T45-E Transaxle (RPOs MN3, MN7, M15, M76, MN4, MN5)

Supercede:

This bulletin is being revised to add the 2004 model year as well as the Chevrolet Classic model. Please discard Corporate Bulletin Number
02-07-30-022A (Section 07-Transmission/Transaxle).

Condition

Some customers may comment that the Service Engine Soon (SES) indicator is illuminated and that while the light is illuminated, transmission
shifts are extremely harsh.
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 86
Chevrolet Venture V6-3.4L VIN E 2411

Cause

These types of conditions may be caused by an intermittent connection at the transaxle 20-way connector to the wiring harness interface.

Correction

If a DTC was recorded and the Freeze Frame and Failure Records back it up, a problem existed at one time with the wiring and/or the connectors
between the transaxle and the PCM. Therefore, a thorough inspection and/or repair of the wiring harness at the transaxle 20-way connector for one
or more of the following conditions may be warranted.

^ The wiring harness is stretched too tightly or other components are pressing on the connector body itself causing a downward pressure on the
connector body and possible intermittent contact of the wiring terminals. Ensure proper clearance to any other components and wiring (i.e.
hoses, battery cables, etc.).

^ The terminals are not fully seated into the cavity of the connector body.

^ The male terminals in the transaxle portion of the connector may be in the wrong position (i.e. bent).

^ The female terminals may be loose and are not making proper contact. Check the tension with the proper terminal tester from the GM Terminal
Test Kit J 35616-A or J 35616-92. If the tension is low, replace the terminal. Do not try to re-form the terminal.

^ The crimp of the terminal to the wire may not be satisfactory (i.e. loose, over insulation, etc.).

^ The wiring connector is not properly seated and locked in position. Ensure proper seating of the connector into the transaxle and that the
connector is properly locked in place.

Warranty Information

For vehicles repaired under warranty, use the table.

Disclaimer
Technical Service Bulletin # 04-09-40-001 Date: 040105

Restraint System - 2nd Row Seat Belt Won't Release


Bulletin No.: 04-09-40-001

Date: January 05, 2004

INFORMATION

Subject:
Correct Location When Servicing Right Side 2nd Row Seat Belt Upper Anchor Bolt

Models:
1997-2004 Chevrolet Venture
1997-2004 Oldsmobile Silhouette
1997-2004 Pontiac Montana

The following information should be used when checking proper seat belt operation or when replacing the right side 2nd row seat belt assembly.
Some of the above listed vehicles may experience a condition where the 2nd row right side seat belt retractor will not release. When the seat belts
are fully extended, they go into a automatic locking mode, or cinch feature. This cinch feature enables the seat belts to stay tight and restrain child
seats developed before the advent of LATCH seats. The cinch feature is engaged by fully extending the seat belt from the retractor. Once engaged,
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 87
Chevrolet Venture V6-3.4L VIN E 2412
the seat belt can retract, but cannot be extended again until the clinch feature is cancelled. The cinch feature is cancelled when the seat belt has fully
retracted.

There are 4 different seating configurations for the second row and two different positions for the seat belt upper anchor bolt. Captain's chairs and
bucket seats use the lower anchor position, while split and full bench seats use the upper position. If a seat belt designed for the bucket or captains
chair is installed in the upper position, it cannot retract far enough to release the cinch feature. If you have a captains chair or bucket with a seat belt
retractor that will not release, check to make sure that the upper anchor bolt is in the lower position on the C-pillar. The bolts are reusable and
self-tapping.

DisclaimerTechnical Service Bulletin # 03-08-42-007A Date: 040109

Lighting - Tail/Brake Lamp Bulb Inoperative


Bulletin No.: 03-08-42-007A

Date: January 09, 2004

TECHNICAL

Subject:
Tail Lamp/Brake Lamp Bulb Inoperative (Replace Bulb and/or Circuit Board)

Models:
2000-2004 Chevrolet Venture
2000-2004 Oldsmobile Silhouette
2000-2004 Pontiac Montana

Supercede:

This bulletin is being revised to add model years. Please discard Corporate Bulletin Number 03-08-42-007 (Section 08 - Body and Accessories).

Condition

Some customers may comment that the upper left hand or right hand tail lamp/brake lamp bulb is inoperative.

Cause

This condition may be the result of moisture entering the lamp housing and changing the bulbs resistance, causing the bulb to burn out and or
melting the circuit board.

Correction

Replace the burned out bulb and the circuit board if needed. Apply dielectric lubricant or dielectric grease to the left hand and right hand tail lamp
bulb terminals.

Refer to Tail Lamp Assembly and or Back up, Sidemarker, Stop, Turn Signal Bulb Replacement in SI.
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 88
Chevrolet Venture V6-3.4L VIN E 2413

Parts Information

Parts are currently available from GMSPO.

Warranty Information

For vehicles repaired under warranty, use the table.

Disclaimer
Technical Service Bulletin # 00-06-02-001 Date: 000101

Engine - Running Hot And/Or Loss of Coolant


Bulletin No.: 00-06-02-001

File In Section: 06 Engine/Propulsion System

Date: January, 2000

Subject:
Engine Running Hot, Overheating and/or Loss of Coolant (Polish Radiator Filler Neck and Replace Radiator Cap)

Models:
1999-2000 Passenger Cars and Trucks with Composite Radiator End Tank

Condition

Some customers may comment on one or more of the following conditions:

^ Engine running hot

^ Engine overheating, and/or

^ Loss of coolant/low coolant message


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 89
Chevrolet Venture V6-3.4L VIN E 2414

Cause

The radiator filler neck may have an imperfection in the sealing surface.

Correction

Important:
DO NOT REPLACE THE RADIATOR.

Using a piece of 400 grit wet/dry sandpaper backed with a flat piece of wood, polish the filler neck sealing surface using a circular motion.

Replace the radiator pressure cap with a cap of the same part number as shown in the GM Service Parts Catalog.

Warranty Information

For vehicles repaired under warranty, use:

Labor Labor
Operation Description Time

J3020 Cap, Radiator Filler - Replace 0.2 hr


Technical Service Bulletin # 00-06-02-004 Date: 000501

Radiator - Brown Substance On Cap & Upper Filler Neck


File In Section: 06 - Engine/Propulsion System

Bulletin No.: 00-06-02-004

Date: May, 2000

TECHNICAL

Subject:
Brown Colored Gel-Like Substance on Radiator Cap and Upper Filler Neck (Replace Radiator Cap and Clean Radiator Upper Filler Neck)

Models:
1997-2000 Buick Century
1996 Chevrolet Lumina APV
1996-2000 Chevrolet Lumina, Monte Carlo
1997-2000 Chevrolet Venture
2000 Chevrolet Impala
1996-1997 Oldsmobile Cutlass Supreme
1996-2000 Oldsmobile Silhouette
1996-1997 Pontiac Trans Sport
1996-2000 Pontiac Grand Prix
1998-2000 Pontiac Montana
with 3.1L or 3.4L Engine (VINs J, M, E, X - RPOs LG8, L82, LA1, LQ1)

Condition

Some customers may comment about a brown colored gel-like substance on the radiator cap and upper filler neck.

Correction

Important:
This condition is unique to the 3.1L and 3.4L engines and should not be confused with the condition described in Corporate Bulletin Number
99-06-02-012B - Rust in Coolant System.

This condition is almost always confined to the radiator cap and upper filler neck, so it is not necessary to change the coolant. keeping the cooling
system full at all times should eliminate future recurrence. Replace the radiator cap and clean the radiator upper filler neck using the procedure and
part numbers listed below.

1. Remove the radiator cap when the engine is cool.

^ Slowly rotate the cap counterclockwise to detent. Do not press down while rotating the pressure cap.

^ Wait until any residual pressure (indicated by a hissing sound) is relieved.


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 90
Chevrolet Venture V6-3.4L VIN E 2415

^ After all hissing stops, continue to rotate counterclockwise until the cap is removed.

2. Using a shop rag, clean the upper radiator filler neck of any residue.

3. Remove the coolant recovery reservoir if visually contaminated. Refer to the Coolant Recovery Reservoir Replacement procedure in the
Engine Cooling sub-section of the appropriate Service Manual.

4. If necessary, clean the coolant recovery reservoir and all hoses attached to it with soap and water. Rinse the reservoir and hoses with clean
water and drain.

Verify that the coolant can flow freely through the hoses.

5. Install the coolant recovery reservoir. Refer to the Coolant Recovery Reservoir Replacement procedure in the Engine Cooling sub-section of
the appropriate Service Manual.

6. Refill the coolant recovery reservoir with a 50/50 mixture of DEX-COOL(R) and clean drinkable or distilled water to the HOT mark. Fill to
the HOT mark to compensate for any air that may be in the cooling system.

7. Fill the radiator to the top of the filler neck.

8. Install the new radiator cap, P/N 10409635, making certain the arrows line up with the overflow tube.

9. Instruct the customer of the importance of maintaining the proper coolant level in the radiator and coolant recovery reservoir.

Parts Information

Part Number Description


10409635 Cap, Radiator Filler

Parts are currently available from GMSPO

Warranty Information
For vehicles repaired under warranty, use:

Labor Labor
Operation Description Time
J3020 Cap, Radiator Filler - Replace 0.2 hr
Add Cleaning Radiator Upper Filler Neck 0.1 hr
& Coolant Recovery Reservoir

DisclaimerTechnical Service Bulletin # 03-07-30-017 Date: 030501

A/T - Grinding Noise/No Vehicle Movement in 'D' or 'R'


File In Section: 07 - Transmission/Transaxle

Bulletin No.: 03-07-30-017

Date: May, 2003

TECHNICAL

Subject:
Grind Noise or No Vehicle Movement when Shifting into Drive or Reverse (Inspect Transaxle, Replace Various Transaxle Components)

Models:
1999-2002 Buick Century, LeSabre, Park Avenue
2002 Buick Rendezvous
1999-2002 Chevrolet Monte Carlo, Venture
2000-2002 Chevrolet Impala
1999-2002 Oldsmobile Intrigue, Silhouette
1999-2002 Pontiac Bonneville, Grand Prix, Montana
2001-2002 Pontiac Aztek
with Transaxle Auto 4-SPD, 4T65-E (RPO MN3)
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 91
Chevrolet Venture V6-3.4L VIN E 2416

Condition

Some customers may comment on a grinding noise when shifting into DRIVE or REVERSE or the vehicle will not move in DRIVE or REVERSE.

Correction

Important:
^ If the vehicle DOES NOT exhibit a grinding condition but DOES exhibit shifting concerns, refer to Corporate Bulletin # 00-07-30-002.

^ When servicing the transaxle side cover gasket, refer to Corporate Bulletin # 01-07-30-032.

^ When servicing the valve body spacer plate and/or gasket, refer to informational Corporate Bulletin # 02-07-30-014.

^ When servicing or replacing the transaxle resulting from this condition, the transaxle cooler MUST be flushed. Refer to informational
Corporate Bulletin # 02-07-30-052.

Follow the service procedure below for diagnosis and correction of the grinding noise condition.

Important:
If metallic debris is found on the transaxle pan magnet, the transaxle must be completely disassembled and cleaned. Failure to properly
clean the transaxle case and internal components may lead to additional unnecessary repeat repairs.

1. Remove the transaxle oil pan and inspect the magnet in the bottom of the pan for metal debris. Refer to SI Document ID # 414136.

2. Remove the transaxle from the vehicle. Refer to the appropriate SI document.

Important:
^ Inspect all the transaxle components for damage or wear. Replace all damaged or worn components. The parts listed below should be
sufficient to correct this concern.

^ This condition does not normally require replacement or reconditioning of the transaxle completely unless there is extensive damage.
Components such as clutches, valve body and torque convertors WILL NOT require replacement to correct this condition.

3. Disassemble the transaxle. Refer to the Transmission Overhaul procedure in Unit Repair, SI Document ID # 633950.
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 92
Chevrolet Venture V6-3.4L VIN E 2417

^ (668) Input Sun Gear, P/N 24204098

^ (672) Input Complete Carrier Assembly, P/N 24204430

^ (674) Input/Reaction Carrier Thrust Bearing Assembly, P/N 24205127

^ (675) Reaction Complete Carrier Assembly, P/N 8646504

^ (676) Reaction Carrier/Sun Gear Thrust Bearing Assembly, P/N 8649353

4. Replace the parts listed above to correct this condition. Refer to Unit Repair Manual, Transmission Overhaul procedure, SI Document ID #
417561; Input and Third Sprag Clutches Disassemble, SI Document ID # 38901; and Input and Third Sprag Clutches Assemble, SI
Document ID # 60415.

5. When servicing or replacing the transaxle resulting from this condition, the transaxle cooler MUST be flushed. Refer to informational
Corporate Bulletin # 02-07-30-052.

Parts Information

Parts are currently available from GMSPO.

Warranty Information
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 93
Chevrolet Venture V6-3.4L VIN E 2418

For vehicles repaired under warranty, use the table.

Important:
^ The recondition transaxle add time is not applicable for this repair. All of the transaxle clutch packs and bushings have not been replaced.

^ The recondition transaxle Carrier/Differential Final Drive Assemble is not applicable for this repair.

DisclaimerTechnical Service Bulletin # 00-08-46-003B Date: 050209

Instruments - GPS System Performance Degradation


Info - Global Position Sensor (GPS) Performance Degradation # 00-08-46-003B - (Feb 9, 2005)

Models:
1996-2005 Passenger Cars and Trucks
2002-2005 Saturn Vehicles

with Navigation Systems and/or OnStar(R)

This bulletin is being revised to include additional information. Please discard Corporate Bulletin Number 00-08-46-003A (Section 08 - Body and
Accessories).

Navigation and OnStar(R) systems require a GPS antenna in order to function properly. This antenna may be located inside the vehicle. If the GPS
antenna is located inside the vehicle, performance of the system may be compromised by window tinting film.

If the GPS system performance is in question and the vehicle has window tinting, a quick diagnostic check can be made by temporarily moving the
GPS antenna to an external vehicle surface, such as the decklid or roof. If the GPS function of the navigation or On Star(R) system operates
normally with the antenna relocated the repair would not be considered a warranty repair. The subsequent repair procedure or GPS placement
would be up to the customer.

Some vehicles have the GPS antenna located on the rear window shelf Objects placed on the rear window shelf such as tissue boxes, books, dolls,
etc,, also have the potential to interfere with GPS performance.

Warranty Information

Repairs made to the vehicle navigation and/or OnStar(R) system, which are the result of window tinting, are not considered warranty repairs.

DisclaimerTechnical Service Bulletin # 99-08-45-005 Date: 991101

Accessory Receptacle/Cigar Lighter - Inoperative


File In Section: 08 - Body and Accessories

Bulletin No.: 99-08-45-005

Date: November, 1999

TECHNICAL

Subject:
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 94
Chevrolet Venture V6-3.4L VIN E 2419
Accessory Receptacle/Cigar Lighter is Inoperative (Check Aftermarket Device Plug for Short to Ground)

Models:
1995-2000 Passenger Cars and Trucks

Condition

Some customers may comment that the cigar lighter or the accessory receptacle is inoperative; or that the internal fuse (within the plug on an
aftermarket device), blows intermittently.

Cause

Certain aftermarket devices have a newly designed power plug with an internal mini fuse. The mini fuse may have an external terminal (which may
be used to externally check the fuse). If the mini fuse external test terminal is not recessed into the mini fuse body, it may come in contact with the
shell of the vehicle receptacle and cause the fuse (of either the vehicle or the aftermarket device), to blow intermittently.

Correction

Test the aftermarket device plug for short to ground. The following step may be performed at the customer's expense. As this is not a defect in
material, design or workmanship of the vehicle, it would be the owner's responsibility.

1. Place a piece of tape over the mini fuse terminal temporarily.

2. Explain to the customer that the fuse for the device must have no exposed terminals, and that finding one would be his responsibility.

3. Refer the customer to the manufacturer of the aftermarket device for a new plug.
Technical Service Bulletin # 00-07-30-007A Date: 020201

A/T - 4T65E, MIL ON/Whine Noise In PARK/NEUTRAL


File In Section: 07 - Transmission/Transaxle

Bulletin No.: 00-07-30-007A

Date: February, 2002

TECHNICAL

Subject:
Whine Noise In Park Or Neutral, Service Engine Soon or Service Vehicle Soon Lamp Illuminates (Replace Drive Sprocket Support Bearing)

Models:
1999-2000 Buick LeSabre, Park Avenue/Ultra, Regal, Riviera
1999-2000 Chevrolet Lumina, Monte Carlo, Venture
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 95
Chevrolet Venture V6-3.4L VIN E 2420
2000 Chevrolet Impala
1999 Oldsmobile Eighty Eight
1999-2000 Oldsmobile Intrigue, Silhouette
1999-2000 Pontiac Bonneville, Grand Prix, Montana
with 3.4L, 3.5L or 3.8L Engine (VINs E, H, K, 1-- RPOs LA1, LX5, L36, L67)
and Hydra-Matic 4T65-E Transaxle/Transmission (RPOs MN3, MN7, M15)

This bulletin is being revised to add the Chevrolet Impala to the models affected. Please discard Corporate Bulletin Number 00-07-30-007 (Section
07 - Transmission/Transaxle).

Condition

Some owners of the listed models equipped with a Hydra-Matic 4T65-E transaxle with a Julian Date prior to 0045 may comment on a whine noise
in PARK and/or NEUTRAL or a Service Engine Soon or Service Vehicle Soon lamp that is illuminated. Upon investigation, a DTC P0741 or
P0742 may be found.

Cause

The above condition may be due to drive sprocket support bearing fluting and/or bearing failure.

Correction

Replace the drive sprocket support bearing. Inspect the channel plate and drive sprocket for any abnormal wear, Turbine shaft for cut seals and/or
nicks, and chain for excessive play due to failed bearings.

Important:
When installing the new bearing, the part number MUST be visible (facing upward). Before installing the drive sprocket, lubricate the bearing
assembly with J 36850 assembly lubricant.

Refer to the 4T65-E Unit Repair Section for the installation procedure.

Service Parts Information

Parts are currently available from GMSPO.

Warranty Information
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 96
Chevrolet Venture V6-3.4L VIN E 2421

For vehicles repaired under warranty, use the table.

DisclaimerTechnical Service Bulletin # 00-07-30-002B Date: 020701

A/T - 4T65E Harsh Shifts/Shudders/Slips/DTC's Set


File In Section: 07 - Transmission/Transaxle

Bulletin No.: 0O-07-30-002B

Date: July, 2002

TECHNICAL

Subject:
Slips, Harsh Upshift or Garage Shifts, Launch Shudders, Flares, Erratic Shifts and Intermittent Concerns, DTC P1811 or P0748 Set (Replace
Pressure Control Solenoid Valve Assembly)

Models:
1997-1999 Buick Riviera
1997-2002 Buick Park Avenue
1998-2002 Buick LeSabre
1999-2002 Buick Regal
2000-2002 Buick Century
2002 Buick Rendezvous
1997-2001 Chevrolet Lumina
1997-2002 Chevrolet Monte Carlo
1999-2002 Chevrolet Venture
2000-2002 Chevrolet Impala
1997-1999 Oldsmobile Eighty Eight
1997-2002 Oldsmobile Silhouette
1998-2002 Oldsmobile Intrigue
2001-2002 Oldsmobile Aurora (3.5L)
1997-2002 Pontiac Bonneville, Grand Prix
1999-2002 Pontiac Transport/Montana
2001-2002 Pontiac Aztek
with Hydra-Matic 4T65-E (RPOs MN3, MN7, M15, M76)

This bulletin is being revised to add additional models and model years. Please discard Corporate Bulletin Number 00-07-30-002A (Section 07 -
Transmission/Transaxle).

Condition

Some owners of the above vehicles with a HydraMatic 4T65-E transaxle may comment on harsh upshifts or harsh garage shifts, soft shifts,
shudders on hard acceleration, or shifts erratic. These conditions may appear intermittently or set a DTC P1811 or P0748. During diagnosis, a low
or high line pressure (actual versus desired) may be observed.

Cause

The above condition may be due to any one of the following which may affect line pressure output:

^ Sediment inside the pressure control (PC) solenoid valve, causing the PC solenoid valve to mechanically bind.

^ Sediment in the valve body, causing the torque signal regulator valve to stick.

^ Incorrect transaxle oil level.


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 97
Chevrolet Venture V6-3.4L VIN E 2422

Correction

Important:
Any of the above conditions may be intermittent, therefore, this test should be performed at least three times.

Refer to the Line Pressure Check Procedure in SI, along with the Line Pressure Specification Table shown, to determine if actual versus desired
pressures are within the values specified. The Scan Tool is only able to control the PC solenoid valve in PARK and NEUTRAL with the vehicle
stopped. This protects the clutches from extremely high or low pressures in DRIVE or REVERSE ranges.

Refer to the Line Pressure Specification Table. The pressures in the table assume a temperature of 70°C. The pressure will vary with a change in
temperature.

If the actual versus desired pressures are not within the values specified, clean the valve body and replace the PC solenoid valve, if necessary.

Check the PC solenoid valve actual versus desired pressures to verify the new PC solenoid valve is responding correctly.

Refer to the Automatic Transaxle Section of the Service Manual for the proper repair procedure.

Line Pressure Check Procedure Tools Required

J 21867 Universal Pressure Gauge Set

Important:
Before performing a line pressure check, verify that the pressure control (PC) solenoid valve is receiving the correct electrical signal from the
PCM.

1. Install a Scan Tool.

Caution:
Keep the brakes applied at all times in order to prevent unexpected vehicle motion. Personal injury may result it the vehicle moves
unexpectedly.

2. Start the engine and set the parking brake.

3. Check for a stored Diagnostic Trouble Code (DTC).

4. Repair the vehicle, if necessary.

5. Check the fluid level. Refer to the Transmission Fluid Checking Procedure.

6. Check the manual linkage for proper adjustment.


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 98
Chevrolet Venture V6-3.4L VIN E 2423

7. Turn the engine OFF. Remove the oil pressure test hole plug and install the J 21867.

8. Put the gear selector in PARK range and set the parking brake.

9. Start the engine and allow the engine to warm up at idle.

Notice:
Total test running time should not be longer than two minutes, or else transmission damage could occur.

10. Access the PC solenoid valve control test on the Scan Tool.

11. Increase the PC solenoid as shown actual current from 0.0 to 1.0 amps in 0.1 amp increments. Allow the pressure to stabilize for five seconds
after each pressure change. Read the corresponding line pressure on the J 21867.

12. Refer to the Line Pressure specification table. Compare the data to the table.

13. If pressure readings differ greatly from the table, refer to Incorrect Line Pressure.

14. Remove the J 21867.

15. Apply sealant, P/N 12345382 (in Canada, P/N 10953489), to the oil pressure test hole plug.

Notice:
Refer to Fastener Notice in Cautions and Notices.

16. Install the oil pressure test hole plug.

Tighten

Tighten the oil pressure test hole plug to 12 N.m (106 lb in).

Parts Information
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 99
Chevrolet Venture V6-3.4L VIN E 2424

Parts are currently available from GMSPO.

Warranty Information

For vehicles repaired under warranty, use the table shown.

DISCLAIMERTechnical Service Bulletin # 04-07-30-028A Date: 060112

A/T - 4T65-E Fluid Leaks From Reverse Servo Cover


Bulletin No.: 04-07-30-028A

Date: January 12, 2006

TECHNICAL

Subject:
4T65-E Automatic Transmission Fluid Leak From Reverse Servo Cover (Replace Reverse Servo Cover Seal)

Models:
2005 and Prior Cars and Light Duty Trucks

with Automatic Transmission 4T65-E (RPOs MN3, MN7, M15, M76)

Supercede:

This bulletin is being revised to announce an improved reverse servo cover seal is available from GMSPO and to advise technicians that it is no
longer necessary to replace the reverse servo cover when replacing the seal. The 2005 model year vehicles are also being added. Please discard
Corporate Bulletin Number 04-07-30-028 (Section 07 - Transmission/Transaxle).

Condition

Some customers may comment on a fluid leak under the vehicle. A transmission fluid leak may be noted during the Pre-delivery Inspection (PDI).

Cause

A possible cause of a transmission fluid leak usually only during cold ambient temperatures below -6.7°C (20°F) may be the reverse servo cover
seal. The reverse servo cover seal may shrink in cold ambient temperatures causing a transmission fluid leak.

Correction

Follow the diagnosis and repair procedure below to correct this condition.

1. Diagnose the source of the fluid leak.


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 100
Chevrolet Venture V6-3.4L VIN E 2425

2. If the source of the transmission fluid leak is the reverse servo cover, replace the reverse servo cover seal with P/N 24235894. Refer to
Reverse Servo Replacement in the appropriate Service Manual.

3. Clean the area around and below the cover.

4. Inspect the transmission fluid level. Refer to Transmission Fluid Checking Procedure in the appropriate Service Manual.

Parts Information

Warranty Information

For vehicles repaired under warranty, use the table.

Disclaimer

Technical Service Bulletin # 01-08-97-002 Date: 011101


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 101
Chevrolet Venture V6-3.4L VIN E 2426

HomeLink(R) Transmitter - Programming Difficulties


File In Section: 08 - Body and Accessories

Bulletin No.: 01-08-97-002

Date: November, 2001

INFORMATION

Subject:
Programming the HomeLink(R) Transmitter

Models:
2000-2002 Passenger Cars and Light Duty Trucks with Universal Garage Door Opener (RPO UG1)

If you have customers that are having difficulties programming their HomeLink(R) transmitter, you may suggest the following options:

^ The customer may contact HomeLink(R) directly at 1-800-355-3515 for assistance. Assistance is available in English, French and Spanish
languages.

^ The customer may also be directed to the HomeLink(R) website at www.homelink.com.

The website is user-friendly and actively demonstrates how to program the transmitter. Many newer garage door openers have a "rolling code"
feature and the website does a great job of guiding the owner through the entire programming process.

The HomeLink(R) phone number, website address, and other useful information can also be found in Section 2 of the Owner's Manual under
HomeLink(R) Transmitter.

DisclaimerTechnical Service Bulletin # 00-09-40-001C Date: 050131

Restraint Systems - Excessive Child Seat Movement


Bulletin No.: 00-09-40-001C

Date: January 31, 2005

TECHNICAL

Subject:
Excessive Lateral Movement of Some Aftermarket Child Seats (Replace Rear Seat Buckle)

Models:
2005 Buick Terraza
1997-2004 Chevrolet Venture
2005 Chevrolet Uplander
1997-2004 Oldsmobile Silhouette
1997-99 Pontiac Trans Sport
1999-2004 Pontiac Montana
2005 Pontiac Montana SV6
2005 Saturn Relay

Supercede:

This bulletin is being revised to add models and the 2005 model year and remove the Opel model. Please discard Corporate Bulletin Number
00-09-40-001B (Section 09 - Restraints).

Condition

Some customers may comment on excessive lateral movement (side to side) when using certain aftermarket child seats. This condition occurs in
vehicles equipped with second and third row bucket seats (RPO AL4).

Correction
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 102
Chevrolet Venture V6-3.4L VIN E 2427

Install a replacement rear seat belt buckle assembly in order to correct this condition.

Important:
This replacement buckle should be used only if the customer is experiencing this condition when using after aftermarket child seat. The
customer should be made aware that the replacement buckle is only available in graphite. You may make the original seat belt buckle assembly
available to the customer for possible reinstallation at a later date. A copy of the procedure below MUST be provided to the customer if the
original seat belt buckle assembly is returned.

For general passenger use, rear seat belt buckle assembly replacements should be made with the original color-coded parts and part numbers as
identified in the Service Parts Catalog.

Removal Procedure

Tools Required

J 29843-9 Door Lock Striker and Seat Belt TORX Wrench (T-50)

Important:
Avoid damaging the bucket seat cushion cover when removing the rear seat belt buckle assembly.

1. Move the seat cushion cover away from the buckle side in order to expose the bolt.

2. Use the J 29843-9 in order to remove the bolt securing the buckle side belt from the seat.

3. Remove the buckle side belt from the seat.

Installation Procedure

1. Use the J 29843-9 to install the bolt securing the buckle side belt to the seat.

Tighten

Tighten the rear seat buckle belt bolt to 53 N.m (39 lb-ft).

2. Reposition the seat cushion cover down over the bolts.

Parts Information

Parts are currently available from GMSPO.

Warranty Information

For vehicles repaired under warranty, use the table.


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 103
Chevrolet Venture V6-3.4L VIN E 2428

Disclaimer
Technical Service Bulletin # 01-08-45-005E Date: 060829

Electrical - Hard or No Start/Warning Lamps ON/DTC's Set


Bulletin No.: 01-08-45-005E

Date: August 29, 2006

TECHNICAL

Subject:
Hard/No Start, Fuel Gauge Inoperative/Fluctuates, SES/Check Engine Light On, ABS Warning Light On, TCS Warning Light On, TCS Activation,
Service Traction System Message Displayed, All-Wheel Drive Disable Message Displayed, DTCs Set (Repair Connector)

Models:
2002-2006 Buick Rendezvous
2005-2007 Buick Terraza
2000-2005 Chevrolet Venture
2005-2007 Chevrolet Uplander
2000-2004 Oldsmobile Silhouette
2000-2005 Pontiac Montana
2001-2005 Pontiac Aztek
2005-2007 Pontiac Montana SV6
2005-2007 Saturn Relay

Supercede:

This bulletin is being revised to add 2007 model year. Also, additional information was added to the Important statement. Please discard Corporate
Bulletin Number 01-08-45-005D (Section 8 - Body and Accessories).

Condition

Some customers may comment on one or more of the following conditions:

Engine is hard to start

Engine will not start

Engine starts then stalls

Fuel gauge is inoperative or fluctuates

Service Engine Soon/Check Engine light is illuminated

ABS Warning Light is illuminated

TCS Warning Light is illuminated

TCS activation

Service Traction System message displayed

All-Wheel Drive Disable message displayed

These conditions may be intermittent. Upon investigation, the technician may find various DTCs set.

Cause

This condition may be due to water leaking into the interior of the vehicle, and/or spread terminals, at connector C305 that is located on the floor to
the rear of the driver's seat. This connector is not sealed from the inside of the vehicle and water may enter the connector causing the terminals to
become corroded. Also, the female terminals of the connector may have become spread apart causing an intermittent poor connection.
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 104
Chevrolet Venture V6-3.4L VIN E 2429

Correction

Inspect the terminals at connector C305 for corrosion or spreading before replacing the fuel module or resistor card kit. Terminals can be accessed
from underneath the vehicle.

Do not attempt to repair any spread female terminals as this will result in a return repair. The female terminal must be replaced.

If the terminals show signs of corrosion, determine the source of the water leak first and repair the water leak before repairing the terminals in
connector C305. Refer to Corporate Service Bulletin Number 01-01-38-009A to determine a potential source for water in the vehicle interior.

Repair any corroded and/or spread female terminals in connector C305. Refer to Repairing Connector Terminals in the Wiring Systems sub-section
of the appropriate service information.

Warranty Information

For vehicles repaired under warranty, use the table.

Disclaimer
Technical Service Bulletin # 01-08-51-004E Date: 061222

Body - Premature Aluminum Hood Blistering


Subject:
Premature Aluminum Panel Hood Corrosion/Blistering (Refinish)
# 01-08-51-004E - (12/22/2006)

Models:
2000-2003 Buick LeSabre
2002-2006 Buick Rendezvous
2000-2005 Cadillac DeVille
2003-2006 Cadillac CTS
2004-2006 Cadillac SRX
2005-2006 Cadillac STS
2006 Cadillac DTS
1997-2005 Chevrolet Trans Sport (Export Only), Venture
1997-2003 Oldsmobile Silhouette
2001-2003 Oldsmobile Aurora
1997-1998 Pontiac Trans Sport
1997-2005 Pontiac Montana
2000-2003 Pontiac Bonneville

This bulletin is being revised to update the affected model years. Please discard Corporate Bulletin Number O1-08-51-004D (Section 08 - Body and
Accessories).

Condition

Some vehicles may have the appearance of blistering or bubbling paint on the top of the hood or under the hood edges and hem flanges.

Correction
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 105
Chevrolet Venture V6-3.4L VIN E 2430

Important:
Always follow your paint manufacturer's instructions for specific product usage.

1. Remove the hood from the vehicle.

2. Wash the complete hood with soap and water.

3. Wash the hood with wax and grease remover.

4. Inspect the hood for paint blistering (top of the hood and under the hood edges and hem flanges).

Important:
Because the hood is made of aluminum only, use clean discs so that the aluminum surface of the hood will not become contaminated with
foreign particles.

5. Clean blister areas by spot media blast or a 3M(R) Roloc clean and strip disc, P/N 07466, or equivalent.

6. Feather edge and clean.

7. Prime the affected area, seal the complete panel perimeter hem flange using 3M # 08370.

8. Refer to your GM 4901M Approved Refinish Materials booklet under the heading of Rigid Substrates (Steel and Aluminum) for product
selection.

The information for the latest GM Approved Refinish Materials booklet is ONLY online at the GM Goodwrench website. Printed books have
been discontinued. Follow these steps to access the site:

^ Go to www.gmgoodwrench.com.

^ Click on GM Collision Parts.

^ Click on GM Technical Repair Information.

^ Click on Paint Shop.

Warranty Information

For vehicles repaired under warranty, use the table.

Disclaimer
Technical Service Bulletin # 04-07-30-013B Date: 070201

Engine, A/T - Shift/Driveability Concerns/MIL ON


Bulletin No.: 04-07-30-013B

Date: February 01, 2007

INFORMATION

Subject:
Automatic Transmission Shift, Engine Driveability Concerns or Service Engine Soon (SES) Light On as a Result of the Use of an
Excessively/Over-Oiled Aftermarket, Reusable Air Filter
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 106
Chevrolet Venture V6-3.4L VIN E 2431

Models:
2007 and Prior GM Cars and Light Duty Trucks
2007 and Prior Saturn Models
2003-2007 HUMMER H2
2006-2007 HUMMER H3
2005-2007 Saab 9-7X

Supercede:

This bulletin is being revised to add models and model years. Please discard Corporate Bulletin Number 04-07-30-013A (Section 07 -
Transmission/Transaxle).

The use of an excessively/over-oiled aftermarket, reusable air filter may result in:

Service Engine Soon (SES) light on

Transmission shift concerns, slipping and damaged clutch(es) or band(s)

Engine driveability concerns, poor acceleration from a stop, limited engine RPM range

The oil that is used on these air filter elements may be transferred onto the Mass Air Flow (MAF) sensor causing contamination of the sensor. As a
result, the Grams per Second (GPS) signal from the MAF may be low and any or all of the concerns listed above may occur.

When servicing a vehicle with any of these concerns, be sure to check for the presence of an aftermarket reusable, excessively/over-oiled air filter.
The MAF, GPS reading should be compared to a like vehicle with an OEM air box and filter under the same driving conditions to verify the
concern.

The use of an aftermarket reusable air filter DOES NOT void the vehicle's warranty.

If an aftermarket reusable air filter is used, technicians should inspect the MAF sensor element and the air induction hose for contamination of oil
prior to making warranty repairs.

Transmission or engine driveability concerns (related to the MAF sensor being contaminated with oil) that are the result of the use of an aftermarket
reusable, excessively/over-oiled air filter are not considered to be warrantable repair items.

DisclaimerTechnical Service Bulletin # 05-06-01-019F Date: 071002

Engine - Oil Leaks from Crankshaft Rear Main Seal


Bulletin No.: 05-06-01-019F

Date: October 02, 2007

TECHNICAL

Subject:
Engine Oil Leak at Crankshaft Rear Main Oil Seal (Install Revised Crankshaft Rear Main Oil Seal Using Revised Rear Main Seal Installer and
Remover Tools)
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 107
Chevrolet Venture V6-3.4L VIN E 2432

Models:
1986-2008 GM Passenger Cars and Light Duty Trucks (including Saturn)

with 2.8L, 3.1L, 3.4L, 3.5L, 3.9L 60 Degree V6 Engine (VINs D, E, F, J, K, L, M, N, R, S, T, V, W, X, Z, 1, 3, 8, 9, W, R - RPOs LG6, LA1, LNJ,
LG8, LL1 or LX9, L82, LL2, LB8, LHO, LG5, LB6, LE2 or LQ1, LH7, LC1, L44, LZ4, LZE, LZ9, LGD, LZ8, LZG)

Supercede:

This bulletin is being revised to add an Important statement on proper seal installation. Please discard Corporate Bulletin Number 05-06-01-019E
(Section 06 - Engine/Propulsion System).

This bulletin only applies to 60 degree V6 engines. Some of the discontinued 60 degree V6 engine VINs and RPOs may have carried over to other
new model year engines and may no longer be a 60 degree V6 engine. So this bulletin may not apply. It is very important to verify that the
following information is correct before using this bulletin:

Year of vehicle (e.g. N = 1992)

V6 Engine Liter size (e.g. 3.4L)

VIN CODE (e.g. X)

RPO (e.g. LQ1)

If ALL the information from the vehicle (year, size, VIN Code, RPO) you're working on can be found under the models listed above, then this
bulletin applies to that engine. If one or more of the vehicle's information can NOT be found under the models listed above, then this bulletin does
NOT apply.

This bulletin does not apply to 2004-2007 Saturn VUE models with 3.5L DOHC V6 Engine (VIN 4 - RPO L66) or 2005-2008 Cadillac CTS with
2.8L HFV6 Engine (VIN T - RPO LP1).

Condition

Some customers may comment on external oil leakage.

Correction

Before replacement of the new design crankshaft rear main oil seal, be sure the PCV system is operating correctly. The new seal described below
comes with a protective nylon sleeve already installed in the seal. This sleeve assures that the seal is installed in the correct direction and also
protects the seal from getting damaged during installation. Do not remove the protective sleeve from the seal; if removed, the installation tool
(EN48108) will not work.

A new design crankshaft rear main oil seal and installation tool (EN-48108) has been released. This seal incorporates features that improve high
mileage durability. Replace the crankshaft rear main oil seal with the new design rear main oil seal, P/N 12592195, using the following service
procedures.

Tools Required

TOOLS WERE SHIPPED TO YOUR DEALERSHIPS. IF YOU HAVE NOT RECEIVED THEM OR THEY ARE LOST, PLEASE CALL GM
SPECIAL SERVICE TOOLS AT 1-800-GM-TOOLS.

EN-48108 Rear Main Oil Seal Installation Tool


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 108
Chevrolet Venture V6-3.4L VIN E 2433

This tool has a unique design to allow the technician to easily install the rear main seal squarely to the correct depth and direction. Before
proceeding with installation, review the above illustration to become familiar with the components shown in the illustration.

EN-48672 rear Main Oil Seal Remover Tool

This tool has a unique design to allow the technician to easily remove the rear main seal without nicking the crankshaft sealing surface when
removing the seal. Before proceeding with removal, review the above illustration to become familiar with the following components:

Removal Plate

Threaded Adjustment Pins and Jam Nuts


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 109
Chevrolet Venture V6-3.4L VIN E 2434

Force Screw

# 2 Self Drill Screws 38 mm (1.5 in) long 8 needed

Extreme Pressure Lubricant

Removal Procedure

Remove the transmission. Refer to Transmission Replacement in SI or the appropriate Service Manual.

Remove the engine flywheel. Refer to Engine Flywheel Replacement in SI or the appropriate Service Manual.

Install the removal plate (2) and both threaded adjustment pins and jam nuts (1) into the back of the crankshaft flange and secure the plate with
adjustment pins and jam nuts.

Install # 2 Self Drill Screws 38 mm (1.5 in) long, eight needed, (1) and tighten down flush to the plate.
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 110
Chevrolet Venture V6-3.4L VIN E 2435

Before installing the force screw, apply a small amount of the Extreme Pressure Lubricant J 23444-A, provided in the tool kit.

Install the force screw (1) and back off both jam nuts (2) and continue to turn the force screw (1) into the removal plate to remove the seal from the
crankshaft.

Once the seal is removed from the crankshaft, remove and save all eight screws and discard the old seal.

Clean the crankshaft sealing surface with a clean, lint free towel. Inspect the lead-in edge of the crankshaft for burrs or sharp edges that could
damage the rear main oil seal. Remove any burrs or sharp edges with crocus cloth or equivalent before proceeding.

Installation Procedure

Do not remove the protective nylon sleeve from the new rear main seal prior to installation. The EN-48108 is designed to install the rear main seal
with the protective sleeve in place. Never apply or use any oil, lubricants or sealing compounds on the crankshaft rear main oil seal.
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 111
Chevrolet Venture V6-3.4L VIN E 2436

Align the mandrel dowel pin (EN-48108) to the dowel pin hole in the crankshaft. Refer to the above illustration.

Using a large flat-bladed screwdriver, tighten the two mandrel screws to the crankshaft. Ensure that the mandrel is snug to the crankshaft hub. Refer
to the above illustration.

Different types (styles) of rear main seals were used in production in different model years, engines and manufacturing facilities. As a result, the
NEW style rear main seal that you will be installing may have a different appearance or shape than the one removed. Regardless of what type of
seal was removed and what side was facing outside the engine, the new seal must be installed as described. Upon close inspection of the outer lip
on the new seal, the words this side out" will be seen. This side of the seal must be facing OUTSIDE the engine when correctly installed. While this
may seem backwards, it is correct. In addition, the protective nylon (plastic) sleeve that the seal is mounted on in the package was designed so that
the seal can only be installed in the proper direction when using the installation tool described in the following steps.

Install the rear main seal (1), with the protective nylon sleeve attached (2), onto the mandrel. The seal, if properly installed, will center on a step
that protrudes from the center of the mandrel. As an error proof, seal will fit only one way onto the mandrel. Refer to the above illustration.
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 112
Chevrolet Venture V6-3.4L VIN E 2437

Before installing the outer drive drum, bearing, washer and the drive nut onto the threaded shaft, apply a small amount of the Extreme Pressure
Lubricant J 23444-A, provided in the tool kit.

Install the outer drive drum onto the mandrel (EN-481 08). Install the bearing, washer and the drive nut onto the threaded shaft. Refer to the above
illustration.

Using a wrench, turn the drive nut on the mandrel (EN-48108), which will push the seal into the engine block bore. Turn the wrench until the drive
drum is snug and flush against the engine block. Refer to the above illustration.

Loosen and remove the drive nut, washer, bearing and drive drum. Discard the protective nylon sleeve.

Verify that the seal has seated properly.

Use a flat-bladed screwdriver to remove the two attachment screws from the mandrel and remove the mandrel from the crankshaft hub. Refer to the
above illustration.

Install the engine flywheel. Refer to Engine Flywheel Replacement in SI or the appropriate Service Manual.

Install the transmission. Refer to Transmission Replacement in SI or the appropriate Service Manual.
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 113
Chevrolet Venture V6-3.4L VIN E 2438

Inspect for proper fluid levels.

Inspect for leaks.

Parts Information

Warranty Information

For vehicles repaired under warranty, use the table.

Disclaimer
Technical Service Bulletin # 05-08-46-004B Date: 080108

OnStar(R) - Number Incorrect/Incorrectly Assigned


Bulletin No.: 05-08-46-004B

Date: January 08, 2008

INFORMATION

Subject:
OnStar(R) Phone Number Concerns (Phone Number Incorrect/Assigned to Another Vehicle/Phone) That Occur During Diagnosis of OnStar(R)
System

Models:
2000-2008 GM Passenger Cars and Trucks
2003-2008 HUMMER H2
2006-2008 HUMMER H3
2003-2008 Saturn Vehicles
2005-2008 Saab 9-7X

with OnStar(R) (RPO-UE1)

Supercede:

This bulletin is being revised to add the 2008 model year. Please discard Corporate Bulletin Number 05-08-46-004A (Section 08 - Body and
Accessories).

During diagnosis of an OnStar(R) concern the technician may be told that the OnStar(R) phone number is incorrect or tied to another vehicle and/or
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 114
Chevrolet Venture V6-3.4L VIN E 2439
phone of some kind. To resolve these concerns the Tech 2(R) with software version 22.005 (or higher) has the capability to change the OnStar(R)
phone number.

Service Procedure

With the Tech 2(R) build the vehicle to specifications within the Diagnostics area of the Tech 2(R).

For vehicles with physical-based diagnostics - under Body go to the OnStar(R) section. Then select the Special Functions menu. For vehicles with
functional-based diagnostics - under Body and Accessories go to the Cellular Communication section. Select Module Setup and then Vehicle
Communication Interface Module.

Locate the Program Phone Number prompt and select it. The original phone number will be displayed on the Tech 2(R) screen.

Contact the OnStar(R) team at the GM Technical Assistance Center (TAC) to obtain a new phone number.

Highlight the digits of the phone number one at a time and enter the new phone number using the number keys on the Tech 2(R).

Press the Soft key at the base of the screen for Done once these numbers have been changed on the screen.

Press the Soft key for Done again. The area code or new phone number has now been programmed into the phone.

Cycle the ignition to Off and open the drivers door.

Press the blue OnStar(R) button to make sure that a normal connection can be made to the OnStar(R) call center. If applicable make sure the
Hands-Free Calling (HFC) works properly by making a phone call.

If the system is working properly fax or voicemail a case closing into the OnStar(R) team at TAC with the results. Dealers in Canada should submit
case closing information through the GM infoNET.

Please follow this diagnostic process thoroughly and complete each step. If the condition exhibited is resolved WITHOUT completing every step
the remaining steps do not need to be performed. If the procedure above does not resolve the condition you must contact TAC for further
assistance. This diagnostic approach was developed specifically for this condition and should not automatically be used for other vehicles with
similar symptoms.

Warranty Information (excluding Saab U.S. Models)

For vehicles repaired under warranty use, the table.

Warranty Information (Saab U.S. Models)

For vehicles repaired under warranty use, the table.


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 115
Chevrolet Venture V6-3.4L VIN E 2440

Disclaimer
Technical Service Bulletin # 02-08-46-006C Date: 080108

OnStar(R) - Incorrect GPS Position Reported During Call


Bulletin No.: 02-08-46-006C

Date: January 08, 2008

INFORMATION

Subject:
Incorrect OnStar(R) Global Positioning System (GPS) Location Reported During OnStar(R) Call

Models:
2000-2008 GM Passenger Cars and Light Duty Trucks (including Saturn)
2003-2008 HUMMER H2
2006-2008 HUMMER H3
2005-2008 Saab 9-7X

with OnStar(R)

Supercede:

This bulletin is being revised to add model years. Please discard Corporate Bulletin Number 02-08-46-006B (Section 08 - Body and Accessories).

A small number of the above-mentioned vehicles may exhibit a condition in which the vehicle reports an inaccurate location to the OnStar(R) Call
Center. This condition can only be identified via a button press to the OnStar(R) Call Center by the customer. Call Center personnel will be able to
identify this inaccurate location condition. Customers will then be notified through the mail by OnStar(R) if their vehicle exhibits this condition.
Once this condition has been identified OnStar(R) will instruct the customer to return to the dealership to have this condition corrected.

It is not necessary to reconfigure the vehicle after the following procedure.

In order to correct this condition you must cycle power to the OnStar(R) system. This can be done by either removing the fuses powering the
OnStar(R) system or disconnecting the OnStar(R) module (VCIM) from the vehicle. As a last resort you can disconnect the vehicle's battery.

The power needs to be removed from the system for approximately 15 minutes.

After completing this procedure the vehicle should be taken to an area with an unobstructed view of the sky. The vehicle should be kept running for
approximately 10 minutes to allow the vehicle to reacquire the global positioning system (GPS). Then contact the OnStar(R) Call Center via the
blue OnStar(R) button and ask the advisor to verify the GPS position.

If the OnStar(R) advisor still has an inaccurate GPS location refer to the Navigation Systems and Cellular Communications sub-sections in the
Service Manual in order to diagnose and repair the concern. If the normal diagnostics lead to module replacement you will need to contact
Technical Assistance (TAC) and choose the OnStar(R) prompt. GM OnStar(R) TAC will assist in the diagnosis and if appropriate order a
replacement part. Replacement parts are usually shipped out within 24 hours and a pre-paid return package label will be included for returning the
faulty part. By returning the faulty part you will avoid a significant non-return core charge.

Warranty Information (excluding Saab US Models)

For vehicles repaired under warranty, use the table.

Warranty Information (Saab US Models)


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 116
Chevrolet Venture V6-3.4L VIN E 2441

For vehicles repaired under warranty use, the table.

DisclaimerTechnical Service Bulletin # 07-06-01-023 Date: 071205

Engine - Oil Leaks From Front Crankshaft Seal


Bulletin No.: 07-06-01-023

Date: December 05, 2007

TECHNICAL

Subject:
60 Degree V6 Engine Oil Leak at Crankshaft Front Oil Seal (Use New Crankshaft Front Oil Seal Installer Tool EN-48869)

Models:
1986-2008 GM Passenger Cars and Light Duty Trucks (including Saturn)

with 2.8L, 3.1L, 3.4L, 3.5L or 3.9L 60 Degree V6 Engine

(VINs D, E, F, J, K, L, M, N, R, S, T, V, W, X, Z, 1, 3, 8, 9, W, R - RPOs LG6, LA1, LNJ, LG8, LL1 or LX9, L82, LL2, LB8, LHO, LG5, LB6,
LE2 or LQ1, LH7, LC1, L44, LZ4, LZE, LZ9, LGD, LZ8, LZG)

This bulletin does not apply to 2004-2007 Saturn VUE models with 3.5L DOHC V6 Engine (VIN 4 - RPO L66) or 2005-2008 Cadillac CTS with
2.8L HFV6 Engine (VIN T - RPO LP1).

This bulletin only applies to 60 degree V6 engines. Some of the discontinued 60 degree V6 engine VINs and RPOs may have carried over to other
new model year engines and may no longer be a 60 degree V6 engine. So this bulletin may not apply. It is very important to verify that the
information shown is correct before using this bulletin.

If ALL the information from the vehicle (year, size, VIN Code, RPO) you're working on can be found under the models listed above, then this
bulletin applies to that engine. If one or more of the vehicle's information can NOT be found under the models listed above, then this bulletin does
NOT apply.

Condition

Some customers may comment on external oil leakage.

Correction

Before replacement of the crankshaft front oil seal, be sure the PCV system is operating correctly.

Tools Required
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 117
Chevrolet Venture V6-3.4L VIN E 2442

TOOLS WERE SHIPPED TO YOUR DEALERSHIPS. IF YOU HAVE NOT RECEIVED THEM OR THEY ARE LOST, PLEASE CALL GM
SPECIAL SERVICE TOOLS AT 1-800-GM-TOOLS.

The EN-48869 has a unique design to allow the technician to easily install the front crankshaft seal squarely to the correct depth and direction.
Before proceeding with installation, review the illustration to become familiar with the tool.

Removal Procedure

Remove the crankshaft balancer. Refer to Crankshaft Balancer Replacement in SI.

Use care not to damage the engine front cover or nick the crankshaft.

Remove the crankshaft front oil seal (1) using a suitable tool.

Installation Procedure
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 118
Chevrolet Venture V6-3.4L VIN E 2443

Lubricate the inside of the crankshaft front oil seal (1) with clean engine oil. Then install the seal to the installer body (2).

Align the oil seal and installer body (1) with the engine front cover and crankshaft.

Before installing the force screw, apply a small amount of the Extreme Pressure Lubricant J 23444-A, provided in the tool kit, to the force screw.

Install the drive nut (4) onto the threaded force screw shaft (5), washer (3), and bearing (2). Then install to the installer body (1) and tighten the
force screw to the crankshaft by hand.

Using a wrench, turn the drive nut on the threaded force screw shaft (2), this will push the seal into the engine front cover.
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 119
Chevrolet Venture V6-3.4L VIN E 2444

Continue to turn the drive nut (2) with the wrench until the installer body (1) is snug and flush against the engine front cover.

Loosen and remove the drive nut from the threaded force screw shaft, washer, bearing, and installer body. Verify that the seal has seated properly,
flush against front cover flange (1).

Install the crankshaft balancer. Refer to Crankshaft Balancer Replacement in SI.

Inspect for proper fluid levels.

Inspect for leaks.

Parts Information

Warranty Information

For vehicles repaired under warranty, use the table.


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 120
Chevrolet Venture V6-3.4L VIN E 2445

Disclaimer
Technical Service Bulletin # 03-06-01-010C Date: 080408

Engine/Cooling System - Oil or Coolant Leaks


TECHNICAL

Bulletin No.: 03-06-01-010C

Date: April 08, 2008

Subject:
Engine Oil or Coolant Leak (Install New Lower Intake Manifold Gasket)

Models:
2000-2003 Buick Century
2002-2003 Buick Rendezvous
1996 Chevrolet Lumina APV
1997-2003 Chevrolet Venture
1999-2001 Chevrolet Lumina
1999-2003 Chevrolet Malibu, Monte Carlo
2000-2003 Chevrolet Impala
1996-2003 Oldsmobile Silhouette
1999 Oldsmobile Cutlass
1999-2003 Oldsmobile Alero
1996-1999 Pontiac Trans Sport
1999-2003 Pontiac Grand Am, Montana
2000-2003 Pontiac Grand Prix
2001-2003 Pontiac Aztek

with 3.1L or 3.4L V-6 Engine (VINs J, E - RPOs LG8, LA1)

Supercede:

This bulletin is being revised to update the Parts Information and add an Important statement. Please discard Corporate Bulletin Number
03-06-01-010B (Section 06 - Engine).

Condition

Some owners may comment on an apparent oil or coolant leak. Additionally the comments may range from spots on the driveway to having to add
fluids.

Cause

Lower Intake manifold may be leaking allowing coolant oil or both to leak from the engine.

Correction

Install a new design lower intake manifold gasket. The material used in the gasket has been changed in order to improve the sealing qualities of the
gasket. When replacing the gasket the lower intake manifold bolts must also be replaced and torqued in sequence to a specification.
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 121
Chevrolet Venture V6-3.4L VIN E 2446

Important:
The gasket kit part number listed below now includes the new bolts (4 long bolts and 4 short bolts) with the pre-applied threadlocker on
them. It is no longer necessary to order the bolts separately when ordering gaskets.

Notice:
An oil leak may result if the vertical bolts are not tightened before the diagonal bolts.

Diagonal bolts may require a crows foot to tighten.

Tighten

1. Tighten the vertical lower intake manifold bolts (1) to 7 N.m (62 lb in).

2. Tighten the diagonal lower intake manifold bolts (2) to 7 N.m (62 lb in).

3. Tighten the vertical lower intake manifold bolts (1)to 13 N.m (115 lb in).

4. Tighten the diagonal lower intake manifold bolts (2) to 25 N.m (18 lb ft).

Parts Information

Warranty Information

For vehicles repaired under warranty, use the table.

Disclaimer
Technical Service Bulletin # 08-07-30-027 Date: 080604

A/T - No Movement in Drive or 3rd Gear


TECHNICAL

Bulletin No.: 08-07-30-027

Date: June 04, 2008

Subject:
No Movement When Transmission is Shifted to Drive or Third - Normal Operation When Shifted to Second, First or Reverse (Replace Forward
Sprag Assembly)

Models:
1982 - 2005 GM Passenger Cars and Light Duty Trucks
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 122
Chevrolet Venture V6-3.4L VIN E 2447
2006 - 2007 Buick Rainier
2006 Cadillac Escalade, Escalade ESV, Escalade EXT
2006 Chevrolet SSR
2006 - 2008 Chevrolet Avalanche, Colorado, Express, Silverado Classic, Silverado, Suburban, Tahoe, TrailBlazer
2006 GMC Yukon Denali, Yukon Denali XL
2006 - 2008 GMC Canyon, Envoy, Savana, Sierra Classic, Sierra, Yukon, Yukon XL
2006 Pontiac GTO
2006 - 2007 HUMMER H2
2006 - 2008 HUMMER H3
2006 - 2008 Saab 9-7X

with 4L60, 4L60E, 4L65E or 4L70E Automatic Transmission (RPOs MD8, M30, M32, M33 or M70)

Condition

Some customers may comment that the vehicle has no movement when the transmission is shifted to DRIVE or THIRD position, but there is
normal operation when it is shifted to SECOND, FIRST or REVERSE position.

Cause

This condition may be caused by a damaged forward sprag assembly (642).

Correction

When inspecting the sprag, it is important to test the sprag for proper operation by holding the outer race (644) with one hand while rotating the
input sun gear (640) with the other hand. The sun gear should rotate only in the counterclockwise direction with the input sun gear facing upward.
If the sprag rotates in both directions or will not rotate in either direction, the sprag elements should be inspected by removing one of the sprag
assembly retaining rings (643). Refer to SI Unit Repair section for forward clutch sprag disassembly procedures.

If the sprag is found to be damaged, make repairs to the transmission as necessary. A new forward roller clutch sprag assembly is now available
from GMSPO.

If clutch debris is found, it is also very important to inspect the Pressure Control (PC) solenoid valve (377) fluid screens. Clean or replace the PC
solenoid (377) as necessary. It is also important to flush and flow check the transmission oil cooler using J45096. Refer to SI Automatic
Transmission Oil Cooler Flushing and Flow Test for the procedure.
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 123
Chevrolet Venture V6-3.4L VIN E 2448

The notches above each sprag must point up as shown when assembled into the outer race.

Bearing Assembly, Input Sun Gear

Snap Ring, Overrun Clutch Hub Retaining

Hub, Overrun Clutch

Wear Plate, Sprag Assembly

Retainer and Race Assembly, Sprag

Forward Sprag Assembly

Retainer Rings, Sprag Assembly

Outer Race, Forward Clutch

Washer, Thrust (Input Carrier to Race)

The following information applies when this sprag is used in 1982-86 transmissions.

The new design sprag can be used on models 1982 through 1986, by replacing the entire assembly (637 - 644). Individual components are NOT
interchangeable.

Important:
The wear plate (640) and input thrust washer (660) are not required with the new sprag. Use of the thrust washer and wear plate with the new
sprag assembly will cause a misbuild (correct end play cannot be obtained).

Parts Information

Warranty Information

For vehicles repaired under warranty, use the table.

DisclaimerTechnical Service Bulletin # 00-07-30-022D Date: 080610

A/T - 4L60/65E, No Reverse/2nd or 4th Gear


TECHNICAL

Bulletin No.: 00-07-30-022D


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 124
Chevrolet Venture V6-3.4L VIN E 2449

Date: June 10, 2008

Subject:
No Reverse, Second Gear or Fourth Gear (Replace Reaction Sun Shell with More Robust Heat Treated Parts)

Models:
1993 - 2005 GM Passenger Cars and Light Duty Trucks
2003 - 2005 HUMMER H2

with 4L60/65-E Automatic Transmission (RPOs M30 or M32)

Supercede:
This bulletin is being revised to add 2005 model year to the parts information. Please discard Corporate Bulletin Number 00-07-30-022C (Section
07 - Transmission/Transaxle).

Condition

Some customers may comment on a no reverse, no second or no fourth gear condition. First and third gears will operate properly.

Cause

The reaction sun gear (673) may not hold inside the reaction sun shell (670).

Correction

Important:
There are FOUR distinct groups of vehicles and repair procedures involved. Vehicles built in the 2001 model year and prior that make use of a
reaction shaft to shell thrust washer:

^ The sun shell can be identified by four square holes used to retain the thrust washer. Use reaction sun shell P/N 24228345, reaction carrier
to shell thrust washer (699B) P/N 8642202 and reaction sun gear shell thrust washer (674) P/N 8642331er (674) P/N 8642331along with the
appropriate seals and washers listed below.

^ Vehicles built in the 2001 model year and prior that have had previous service to the reaction sun shell: It is possible that some 2001 and
prior model year vehicles have had previous service to the reaction sun shell. At the time of service, these vehicles may have been updated
with a Reaction Sun Shell Kit (Refer to Service Bulletin 020730003) without four square holes to retain the thrust washer. If it is found in a
2001 model year and prior vehicles that the reaction sun shell DOES NOT have four square holes to retain the thrust washer, these vehicles
must be serviced with P/Ns 24229825 (674), 24217328 and 8642331 along with the appropriate seals and washers listed below.

^ Vehicles built in the 2001 model year and later that make use of a reaction shaft to shell thrust bearing: The sun shell can be identified by no
holes to retain the thrust washer. Use reaction sun shell, P/N 24229825, reaction carrier shaft to shell thrust bearing (669A), P/N 24217328
and reaction sun gear shell thrust washer (674), P/N 8642331 along with the appropriate seals and washers listed below.

^ Vehicles built from November, 2001 through June, 2002: These vehicles should have the reaction carrier shaft replaced when the sun shell
is replaced. Use shell kit P/N 24229853, which contains a sun shell (670), a reaction carrier shaft (666), a reaction carrier shaft to shell
thrust bearing (669A) and a reaction sun gear shell thrust washer (674). The appropriate seals and washers listed below should also be used.

When servicing the transmission as a result of this condition, the transmission oil cooler and lines MUST be flushed. Refer to Corporate Bulletin
Number 02-07-30-052.

Follow the service procedure below for diagnosis and correction of the no reverse, no second, no forth condition.

Important:
If metallic debris is found on the transmission magnet, the transmission must be completely disassembled and cleaned. Metallic debris is
defined as broken parts and pieces of internal transmission components. This should not be confused with typical "normal" fine particles
found on all transmission magnets. Failure to properly clean the transmission case and internal components may lead to additional repeat
repairs.

1. Remove the transmission oil pan and inspect the magnet in the bottom of the pan for metal debris. Refer to SI Document ID # 825141.

2. Remove the transmission from the vehicle. Refer to the appropriate SI document.
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 125
Chevrolet Venture V6-3.4L VIN E 2450

Important:
^ Inspect all the transmission components for damage or wear. Replace all damaged or worn components. The parts shown above
should be sufficient to correct this concern.

^ This condition does not normally require replacement of the transmission completely. Components such as clutches, valve body,
pump and torque converters will NOT require replacement to correct this condition.

Disassemble the transmission and replace the appropriate parts listed below. Refer to the Unit Repair Manual - Repair Instructions.

3. Reinstall the transmission in the vehicle. Refer to appropriate service information.

When servicing the transmission as a result of this condition, the transmission oil cooler and lines MUST be flushed. Refer to Corporate
Bulletin Number 02-07-30-052.
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 126
Chevrolet Venture V6-3.4L VIN E 2451

Parts Information

Warranty Information

For vehicles repaired under warranty, use the table.

DisclaimerTechnical Service Bulletin # 01-07-30-032E Date: 080929

A/T - 4T65E Fluid Leaking From A/T Vent


TECHNICAL

Bulletin No.: 01-07-30-032E

Date: September 29, 2008

Subject:
Transmission Oil Leaking From Transmission Vent (Replace Transmission Case Cover (Channel Plate) Gasket)

Models:
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 127
Chevrolet Venture V6-3.4L VIN E 2452
1997-2009 GM Passenger Cars and Light Duty Trucks (including Saturn)

with Hydra-Matic 4T65-E Automatic Transmission (RPOs MN3, MN7, M15, M76)

Supercede:

This bulletin is being revised to add the 2008 and 2009 model years. Please discard Corporate Bulletin Number 01-07-30-032D (Section 07 -
Transmission/Transaxle).

Condition

Some customers may comment on a transmission oil leak.

Cause

This condition may be caused by an improperly torqued channel plate gasket.

Correction

To correct this condition, replace the case cover (channel plate) gaskets (429 and 430). Refer to Unit Repair publication in SI of the appropriate
vehicle being serviced.

Visual inspection of the upper gasket (1) will reveal damage at the referenced area.

Parts Information

Warranty Information

For vehicles repaired under warranty, use the table.

Disclaimer

Technical Service Bulletin # 09-08-48-002A Date: 090319

Body - Marks/Stains on Windshield When Wet


TECHNICAL
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 128
Chevrolet Venture V6-3.4L VIN E 2453

Bulletin No.: 09-08-48-002A

Date: March 19, 2009

Subject:
Marks/Stains on Windshield When Wet (Clean Windshield)

Models:
2010 and Prior Passenger Cars and Trucks (Including Saturn and Saab)
2010 and Prior HUMMER H2, H3

Supercede:
This bulletin is being revised to update the models and model years. Please discard Corporate Bulletin Number 09-08-48-002 (Section 08 - Body
and Accessories).

Condition

Some owners may comment that marks/stains appear on the windshield when the windshield is wet.

Cause

This condition may be caused by contact between the windshield and the vacuum hoses or other tools used in the assembly process. This contact
may leave a residue that creates a water repellent surface on the glass which, in wet conditions, appear as marks/stains on the surface.

Correction

Important
DO NOT REPLACE THE WINDSHIELD FOR THIS CONDITION.

To clean the windshield, use Eastwood Glass Polishing Compound*. Follow the manufacturer's directions for product use. Use only hand tools. DO
NOT USE POWER TOOLS.

Parts Information

Eastwood Glass Polishing Compound

1-800-343-9353 (for overseas inquiries: +1-610-705-2200)

http://www.eastwoodco.com/

*We believe this source and their products to be reliable. There may be additional manufacturers of such products. General Motors does not
endorse, indicate any preference for or assume any responsibility for the products from this firm or for any such items which may be available from
other sources.

Warranty Information

For vehicles repaired under warranty, use the table above.

Disclaimer

Technical Service Bulletin # 09-09-40-001 Date: 090217

Restraints - Seat Belt Warning Lamp On/Buckling Issues


INFORMATION

Bulletin No.: 09-09-40-001


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 129
Chevrolet Venture V6-3.4L VIN E 2454

Date: February 17, 2009

Subject:
Seat Belt Buckle Latching Issues and/or Seat Belt Warning Lights Illuminated

Models:
2010 and Prior GM Passenger Cars and Trucks (Including Saturn)
2010 and Prior HUMMER H2, H3
2010 and Prior Saab 9-7 X

This bulletin is being published to advise dealers about seat belt buckles not operating and/or seat belt warning light illumination, as well as
difficulty latching and unlatching the buckle or the buckle release button sticking.

Analysis of warranty data has determined that this condition may be caused by sticky beverages being spilled onto or into the seat belt buckle
assembly. Foreign debris from food, candy wrappers, paper and coins can also contribute to this condition.

Important:

If foreign material (debris) or sticky liquids are the cause of the concern, show the customer the condition of the component (buckle assembly) and
explain how it is affecting the function of the restraint system. Strongly recommend that the component be replaced. Point out the fact that this is
not a manufacturing defect and is not covered by the new vehicle warranty. If the customer declines to have parts replaced, the service department
management must make a notation on the service record that the lack of functionality of seating position with an inoperative buckle was fully
explained to the customer. The service department management must advise the customer that having a non-functioning buckle in a seating position
voids ability to use that seating position (no one should ride in the seat). Also make the customer aware that it may be against the law to ride in a
vehicle without wearing a restraint system.

Important:

Never insert anything other than the seat belt latch plate into the buckle assembly. Do not attempt to dig anything out of a buckle with a tool. Never
try to wash out a buckle to remove a spilled liquid as this may damage the buckle.

Use the following steps to determine the cause of the concern.

1. Inspect the buckle assembly with a light shining on the latch plate insertion area. Look for any debris or foreign objects in the buckle.

2. If any debris or foreign objects are observed, try to vacuum out the item. After the foreign material is removed, latch and unlatch the seat belt. If
the system functions properly, do not replace the seat belt buckle assembly.

3. If the condition has not been corrected, inspect the buckle assembly for any sticky residue. If sticky residue is found, inform the customer that a
substance was spilled on the seat belt buckle assembly causing the malfunction. The buckle assembly will need to be replaced at the customer's
expense.

4. Refer to SI for seat belt component replacement.

Important:

If foreign material (debris) or sticky liquids are the cause of the concern, show the customer the condition of the component (buckle assembly) and
explain how it is affecting the function of the restraint system. Strongly recommend that the component be replaced at the customer's expense. Point
out the fact that this is not a manufacturing defect and is not covered by the new vehicle warranty. If the customer declines to have parts replaced,
the service department management must make a notation on the service record that the lack of functionality of seating position with an inoperative
buckle was fully explained to the customer. The service department management must advise customer that having a non-functioning buckle in a
seating position voids ability to use that seating position (no one should ride in the seat). Also make the customer aware that it may be against the
law to ride in a vehicle without wearing a restraint system.

5. If further restraint diagnosis is required, refer to Seat Belt System Operational and Functional Checks in SI.

DisclaimerTechnical Service Bulletin # 99-01-39-004C Date: 090612

A/C - Musty Odors Emitted From (HVAC) System


TECHNICAL
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 130
Chevrolet Venture V6-3.4L VIN E 2455

Bulletin No.: 99-01-39-004C

Date: June 12, 2009

Subject: Air Conditioning Odor (Install Evaporator Core Dryer Kit and Apply Cooling Coil Coating)

Models:

1993-2010 GM Passenger Cars and Trucks (Including Saturn)


2010 and Prior HUMMER H2, H3
All Equipped with Air Conditioning

Supercede:
This bulletin is being revised to add the 2009 and 2010 model years. Please discard Corporate Bulletin Number 99-01-39-004B (Section 01 -
HVAC).

Condition

Some customers may comment about musty odors emitted from the Heating, Ventilation and Air Conditioning (HVAC) system at vehicle start-up
in hot, humid conditions.

Cause

This condition may be caused by condensate build-up on the evaporator core, which does not evaporate by itself in high humidity conditions. The
odor may be the result of microbial growth on the evaporator core. When the blower motor fan is turned on, the microbial growth may release an
unpleasant musty odor into the passenger compartment.

There are several other possible sources of a musty odor in a vehicle. A common source is a water leak into the interior of the vehicle or foreign
material in the HVAC air distribution system. Follow the procedures in SI for identifying and correcting water leaks and air inlet inspection.

The procedure contained in this bulletin is only applicable if the odor source has been determined to be microbial growth on the evaporator core
inside the HVAC module.

Correction

Many vehicles currently incorporate an afterblow function within the HVAC control module software. The afterblow feature, when enabled,
employs the HVAC blower fan to dry the evaporator after vehicle shut down and this function will inhibit microbial growth. Technicians are to
confirm that the customer concern is evaporator core odor and that the vehicle has the imbedded afterblow feature, as defined in the SI document
for that specific vehicle model, model year and specific HVAC option. Refer to SI for enabling the afterblow function. Vehicles being delivered in
areas prone to high humidity conditions may benefit from having the afterblow enabled calibration installed prior to any customer comment.

Important
If the vehicle is not factory equipped with the imbedded afterblow enable feature, it may be added with the Electronic Evaporator Dryer
Module Kit (P/N 12497910 or AC Delco 15-5876).

Important
When installing the Electronic Evaporator Dryer Module, you MUST use the included electrical splice connectors to ensure a proper splice.
Complete detailed installation instructions and self testing procedures are supplied with the kit. If necessary, the Electronic Evaporator Dryer
Module may be installed underhood if it is protected from extreme heat and water splash areas.

To immediately remove the evaporator core odor on all suspect vehicles, it is necessary to eliminate the microbial growth and prevent its
re-occurrence. To accomplish this, perform the following procedure:

Vehicle and Applicator Tool Preparation


1. The evaporator core must be dry. This may be accomplished by disabling the compressor and running the blower fan on the recirc heat
setting for an extended period of time.

Note
Compressor engagement will cause the evaporator core to remain wet and will prevent full adherence of the Coiling Coil Coating to the
evaporator core surfaces.

2. Verify that the air conditioning drain hose is not clogged and place a drain pan beneath the vehicle.
3. Place a protective cover over the carpet below the evaporator core.
4. Remove the cabin air filter, if equipped, and cover the opening prior to applying the Cooling Coil Coating, as the product may clog the filter.
If the cabin air filter appears to have little or no remaining life, suggest a replacement to your customer.
5. If the HVAC module has a blower motor cooling tube, be careful NOT TO SPRAY THE COOLING COIL COATING INTO THE
BLOWER MOTOR COOLING TUBE.
6. Attach the Flexible Applicator Pressure Spray Tool (J-43810-20A) to a compressed air line operating at 586 kPa (85 psi) to 793 kPa (115
psi).
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 131
Chevrolet Venture V6-3.4L VIN E 2456
7. Shake the bottle of Cooling Coil Coating well. Screw the bottle onto the cap on the applicator tool's pick-up tube.

Note
The pick-up tube is designed for 120 ml (4 oz) and 240 ml (8 oz) bottles and should coil slightly in the bottom of a 120 ml (4 oz) bottle.

8. Use one of the following three methods to apply the Cooling Coil Coating.

Important
If the Pressure Applicator Spray Tool (J-43810-20A) is not available, the Cooling Coil Coating is also available in an aerosol can (P/N
12377951 (in Canada, 10953503)).

Application Through Blower Motor Control Module Opening


- Remove the blower motor control module (blower motor resistor). Refer to the applicable procedure in SI.
- Clean any debris or foreign material from inside the HVAC module and on the evaporator core surface.
- Apply the Cooling Coil Coating directly to the evaporator core through the blower motor blower motor control module (blower motor
resistor) opening.
- Use the flexible wand to direct the Cooling Coil Coating over the entire evaporator core and surrounding gasket surfaces.
- When the application is complete, install the blower motor blower motor control module (blower motor control module).

Application Through Blower Motor Opening


- Remove the blower motor. Refer to the applicable blower motor removal procedure in SI.
- Clean any debris or foreign material from inside the HVAC module and on the evaporator core surface.
- Apply the Cooling Coil Coating directly to the evaporator core through the blower motor opening.
- Use the flexible wand to direct the Cooling Coil Coating over the entire evaporator core and surrounding gasket surfaces.
- When the application is complete, install the blower motor.

Application Through a Hole in the HVAC Module


- If neither of the two previous application methods are available, it may be necessary to drill a hole in the HVAC module.
- Locate an area of the HVAC module between the blower motor and the evaporator core. Drill a 10 mm (3/8 in) hole in the HVAC
module. Use caution to keep the drill clear of the evaporator core and the blower motor fan.
- With the air distribution vents closed and the blower motor fan speed on HIGH, insert the applicator tool into the hole and spray the
Cooling Coil Coating into the airstream toward the evaporator core.
- Use a GM approved RTV sealant to plug the hole in the HVAC module.

9. After the Cooling Coil Coating application is complete, start and run the vehicle for approximately 10 minutes, with the compressor disabled,
HVAC mode set to Recirculate/Max, heat set to full warm, blower motor fan speed on high, and one window open approximately 12 mm (1/2
in). This cures the Cooling Coil Coating onto the evaporator core surface.
10. While the engine is running, rinse the applicator tool with warm water to prolong the life of the tool. Be sure to spray warm water through the
nozzle to rinse out any residual Cooling Coil Coating still in the capillary pick up tube, otherwise it will dry and clog the applicator tool. Also
remove the small green valve from the bottle cap and rinse it thoroughly while rolling it between two fingers and then reinstall it. If this valve
is clogged , the Cooling Coil Coating will not flow through the applicator tool.
11. Shut off the engine and enable the compressor again.
12. Verify proper HVAC system operation.
13. Remove the protective cover from inside the vehicle.
14. Remove the drain pan from underneath the vehicle.
15. Reinstall the cabin air filter if necessary.

Parts Information

Important
The Cooling Coil Coating listed below is the only GM approved product for use under warranty as an evaporator core disinfectant and for
the long term control of evaporator core microbial growth.

Warranty Information
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 132
Chevrolet Venture V6-3.4L VIN E 2457

For vehicles repaired under warranty, use the table above.

Disclaimer

Technical Service Bulletin # 06-08-44-015B Date: 090512

Audio System - Noise When Using Portable Playback Unit


INFORMATION

Bulletin No.: 06-08-44-015B

Date: May 12, 2009

Subject: Information on Eliminating Noise in Audio System When Using Portable Playback Device

Models:

2010 and Prior GM Passenger Cars and Trucks (Including Saturn)


2010 and Prior HUMMER H2, H3
2005-2009 Saab 9-7X

..........................................................................................................................................................................................................................................
Supercede:
This bulletin is being revised to add model years. Please discard Corporate Bulletin Number 06-08-44-015A (Section 08 - Body and
Accessories).

..........................................................................................................................................................................................................................................

Some portable audio equipment may be susceptible to certain types of electronic noise present in the vehicle's 12V power outlet.

Here are two ways to eliminate this type of interference:

- If the audio device is capable of being self-powered (battery), use it that way instead of plugging it into the vehicle's power outlet.
- Have the customer purchase a Ground Loop Isolator, such as *Radio Shack Catalog #270-054. This device plugs in between the radio and
the customer's audio device. It is packed with one included Y-Adapter. If purchasing the *Radio Shack product, you will require an
additional Y-Adapter (Catalog #274-369). This device should be installed between the audio player and the AUX input of the vehicle radio.
These catalog numbers are stocked nationally at *Radio Shack Retail Stores in the U.S. and are currently available. Other similar products are
available through other electronics or car stereo retailers defined as Ground Loop Isolators.

Parts Information

Parts are currently available nationally in the U.S. through *Radio Shack retail locations or through the mail at Radio Shack direct ordering
1-800-843-7422. In Canada, parts are available nationally through *The Source By Circuit City retail locations or at www.thesourcecc.com.

*We believe these sources and their products to be reliable. There may be additional manufacturers of such products/materials. General Motors
does not endorse, indicate any preference for or assume any responsibility for the products or material from these firms or for any such items that
may be available from other sources.
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 133
Chevrolet Venture V6-3.4L VIN E 2458

Disclaimer
Technical Service Bulletin # 05-08-51-008C Date: 090622

Body - Bumps or Rust Colored Spots in Paint


TECHNICAL

Bulletin No.: 05-08-51-008C

Date: June 22, 2009

Subject: Bumps or Rust Colored Spots in Paint Due to Rail or Iron Dust (Remove Rail Dust)

Models:

1994-2010 GM Passenger Cars and Trucks (Including Saturn)


2003-2010 HUMMER H2
2006-2010 HUMMER H3
2005-2009 Saab 9-7X

Supercede:
This bulletin is being revised to add model years. Please discard Corporate Bulletin Number 05-08-51-008B (Section 08 - Body and Accessories).

Condition

Visible rust colored spots or bumps on a vehicle's paint surface from rail or iron dust.

Cause

Rail dust comes from tiny iron particles produced from the friction between train wheels and the tracks and gets deposited on the vehicle surfaces.
Iron dust can get deposited on the surface if the vehicle is stored near any operation producing iron dust such as an iron ore yard. Either material
can lay on top of, or become embedded in, the paint surface.

Correction

Because the severity of the condition varies, proper diagnosis of the damage is critical to the success of repairs. Diagnosis should be performed on
horizontal surfaces (hood, roof, deck lid, pick up box, etc.) after the vehicle has been properly cleaned. There are two types of repair materials
recommended to repair rail dust or iron dust:

1. GEL TYPE OXALIC ACID:


- Has the characteristics of the liquid type oxalic acid but stays where you put it because of its gel consistency.
2. CLAY TYPE NON-ACID BASED:
- Requires surface lubricant during use.
- Has different grades available.

Caution

Rail dust remover (Oxalic Acid) is an acidic substance containing chemicals that will break down the iron particles embedded in the finish. When
working with rail dust remover, use the necessary safety equipment, including gloves and goggles. Follow the chemical manufacturer's directions
closely because it may require special handling and disposal.

If, upon inspection, some particles are still present, the various chemical manufacturer's processes can be repeated.

After the removal process, small pits may remain in the clearcoat and can be corrected, in most cases, with a finesse/polish operation.

Procedure

1. Move the vehicle to a cool shaded area and make sure that the vehicle surfaces are cool during the removal process. DO NOT PERFORM
THE REMOVAL PROCESS IN DIRECT SUNLIGHT OR ON A VEHICLE WITH HOT OR WARM BODY PANELS.
2. Wash the vehicle with soap and water. Dry it immediately and clean the affected areas with a wax and grease remover.
3. Perform the removal process according to the chemical manufacturer's directions.
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 134
Chevrolet Venture V6-3.4L VIN E 2459

Once the damage has been repaired, the final step involves a polishing process.

Rail Dust Remover Manufacturers

Use the chemical manufacturers listed below, or equivalent:

Auto Magic(R) or Clay Magic(R) products available from:

Auto Wax Company, Inc.


1275 Round Table Dr.
Dallas, TX 75247
(800) 826-0828 (Toll-Free) or (214) 631-4000 (Local)
Fax (214) 634-1342
www.automagic.com
info@autowaxcompany.com
E038 Fallout Gel or E038E Liquid Fallout Remover II available from:

Valvoline Car Brite Company


1910 South State Avenue
Indianapolis, In 46203
(800) 347-2439 (Toll Free) or (317) 788-9925 (Local)
Fax (317) 788-9930
www.carbrite.com
info@carbrite.com
*We believe these sources and their products to be reliable. There may be additional manufacturers of such products. General Motors does not
endorse, indicate any preference for or assume any responsibility for the products from these firms or for any such items which may be available
from other sources.

If rail dust remover is not available in your area, call one of the numbers listed above for a distributor near your location.

Warranty Information (excluding Saab U.S. Models)

Important
Refer to the Policy & Procedures Manual, section 1.2.1.7 for detailed information regarding warranty coverage for this condition.

Important
In certain cases where the vehicle finish is severely damaged and the actual repair time exceeds the published time, the additional time
should be submitted in the "Other Labor Hours" field.

Warranty Information (Saab U.S. Models)

Disclaimer

Technical Service Bulletin # 09-08-48-006 Date: 090918

Body - Stain/Film On Windshield Glass Perimeter


TECHNICAL
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 135
Chevrolet Venture V6-3.4L VIN E 2460

Bulletin No.: 09-08-48-006

Date: September 18, 2009

Subject: Clear Stain or Film on Inside Perimeter of Windshield Glass (Clean/Polish Glass)

Models:

2010 and Prior Passenger Cars and Trucks (Including Saturn and Saab)
2010 and Prior HUMMER H2, H3

Condition

Some customers may comment on a clear stain or film on the inside of the windshield glass. This condition appears along the outer edges of the
glass along the top, bottom or A-pillar areas. Normal glass cleaning procedures will not remove the stain.

Cause

The assembly plant uses a clear sealer/primer on the outer edge of the windshield glass to improve adhesion to the urethane adhesive that bonds the
windshield glass to the vehicle body. Excess sealer/primer may drip or flow onto the windshield and cause a stain. Once the sealer/primer dries, it
may appear to have etched the glass.

Correction

Note

A "white" type of toothpaste is recommended for this repair. Gel-type toothpaste may provide less satisfactory results.

Use a small amount of toothpaste on a soft, cotton cloth to polish the stained area. It may be necessary to wrap the cloth around a paint stir stick or a
similar tool to reach the lower corners of the windshield glass.

After polishing the glass, clean the inside of the windshield glass with a clean, damp, cotton cloth and verify all of the stain is removed. Do not use
any cleaners or solvents - use only clean warm water.

Warranty Information (excluding Saab U.S. Models)

For vehicles repaired under warranty, use:

Warranty Information (Saab U.S. Models)

For vehicles repaired under warranty, use the table.

Disclaimer

Technical Service Bulletin # 03-08-48-006G Date: 100226


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 136
Chevrolet Venture V6-3.4L VIN E 2461
A/C - Window Defroster Contact/Tab Repair Information
INFORMATION

Bulletin No.: 03-08-48-006G

Date: February 25, 2010

Subject: Repair Information for Reconnection of Rear Window Defroster Contact or Tab

Models:

2000-2010 GM Passenger Cars and Trucks (including Saturn)


2003-2009 HUMMER H2
2006-2010 HUMMER H3
2005-2009 Saab 9-7X
2007-2010 Opel GT
2007-2008 Daewoo G2X
Equipped With Electric Rear Window Defroster - RPO C49

Supercede:
This bulletin is being revised to add the 2010 model year. Please discard Corporate Bulletin Number 03-08-48-006F (Section 08 - Body and
Accessories).

Repair Suggestions

Soldering Defroster Contact Tabs

In many cases the terminal tab will still be in the connector when you examine the vehicle. For Chevrolet Tahoe, Suburban, GMC Yukon, and
Cadillac Escalade vehicles (with moveable glass), always replace the defroster tab (GM P/N 25916031) and the defroster electrical power connector
(P/N 12034110). For all other vehicles, reconnect the original defroster tab.

In most applications it is preferable to create a new solder connection to reattach a separated rear defroster tab. If you take note of the steps below,
it is possible to create a new solder joint that is equal to, or stronger than, the original. The generic procedure below is not very time intensive, but
does include minor preparation work to create a good bonding surface. Be sure to follow each of the steps, as combined they will produce the
strongest bond possible. Please consider the following before attempting the repair:

- Soldering introduces significant heat to the glass window of the vehicle. When performing the re-connection of the tab, use only the heat
required to do the job. Pre-heat the soldering iron and have the solder in your other hand, ready to go, the moment you have enough heat to
melt the solder.
- If it is winter, bring the vehicle into the service garage and remove any snow from the back window area. Allow time for the glass to warm to
the temperature inside the building. Soldering creates a "hot spot" in the glass. DO NOT solder on cold glass.

Caution
Heating the glass excessively, or repeatedly without time to cool, may result in glass breakage. ALWAYS wear safety glasses when
performing this repair!

- You MUST use a silver-bearing solder to make the connection. DO NOT attempt this repair with conventional tin/lead alloy solders. Silver
bearing solder will adhere to the electrical buss bar, making a strong and lasting repair.
- Protect surfaces under the area to be soldered. It is very easy to drip solder when performing this repair. Pacing a shop towel under the
soldering area is sufficient protection.

Soldering Procedure
1. It is imperative to remove and replace the rear defroster electrical power connector by crimping a new connector to the feed wire. The proper
connector P/N 12034110 can be found in the Packard Electrical Assortment, Tray 18, Position 5.

- Insert Delphi pick 12094430 to depress the locking tab on the terminal.
- Insert Delphi pick 12094429 to release the secondary lock tab.

Important
DO NOT re-use the existing defroster tab on new-style full-size utility vehicles with moveable glass.

2. Connect the electrical connector to the defroster tab. Fully engage the connector. An improperly seated connector may cause excessive
resistance and impede the proper operation of the defroster. Add a small bead of solder to mate the electrical connector tab to the defroster
tab.
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 137
Chevrolet Venture V6-3.4L VIN E 2462

3. Prepare the surface of the used defroster tab (not required for new tabs on new-style full-size utility models) and the defroster buss bar with
fine grain (500 grit) sandpaper or Emery cloth. It is not necessary to remove all of the original solder, but it should be scuffed sufficiently so
that no oxidation is present. The photo above shows a close up of a properly prepared surface.
Tip
You may want to mask the glass around the contact area with tape. This is easy to do and will allow you to safely prepare the contact surface
without the risk of scratching the glass or the black painted shading.

Important
Most rear glass has a black painted masking around the edge of the glass. When cleaning up the connection surface, be very careful
not to damage the surface of the black shading or the surface of the glass.

4. Wipe the newly prepared contact area with Kent Automotive* Acrysol(TM) (or equivalent) to remove any residual oil or dirt.

Important
You MUST use a silver-bearing solder to make the solder joint. DO NOT attempt this repair with conventional tin/lead alloy solders.
Most suppliers have this type of solder available and it is available nationally at Radio Shack(R)*. It is sold in several diameters and either
are acceptable for this repair.

5. For this step, it is permitted that two technicians be used if required. Heat the new connector on the surface of the buss bar that is to be
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 138
Chevrolet Venture V6-3.4L VIN E 2463
soldered. Long nose pliers are suggested to hold the electrical connector and the defroster tab in place. Keep the solder ready and begin
flowing out the solder as soon as the melting temperature has been reached.
Tip
If a single technician is attempting this repair, it is beneficial to wrap one turn of the solder around the new contacts base. In this manner, as
the melting point of the solder is reached, a layer is deposited on the bottom side of the contact.

Important
Try to align the new contact so that it is positioned with the same orientation as the original contact.

6. The above illustrates an ideal finished solder joint. Additional stray solder will not harm the performance of the bond; however, while it is
unlikely that customers may refer to the appearance of the rear window defroster and its components as a positive styling feature of the
vehicle interior, it is easy to elicit the opposite reaction due to a poor cosmetic application.

*We believe this source and their products to be reliable. There may be additional manufacturers of such products/materials. General Motors does
not endorse, indicate any preference for, or assume any responsibility for the products or material from this firm or for any such items that may be
available from other sources.

Parts Information

Acrysol(TM) can be ordered directly from Kent Automotive at 1-800-654-6333 (in Canada, 1-800-563-1717).

Radio Shack(R) products can be found nationally at retail locations, www.radioshack.com, or at 1-800-843-7422.

In Canada, use The Source by Circuit City(TM) - www.thesourcecc.ca or telephone 1-866-454-4426 (for English) or 1-866-544-4431 (for French),
or at an equivalent retail location.

All other parts can be ordered through GMSPO or SSPO.

Warranty Information (excluding Saab U.S. Models)

For vehicles repaired under warranty, use:

Warranty Information (Saab U.S. Models)

For vehicles repaired under warranty, use the table above.


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 139
Chevrolet Venture V6-3.4L VIN E 2464

Disclaimer

Technical Service Bulletin # 05-03-10-003F Date: 100427

Tires/Wheels - Low Tire/Leaking Cast Aluminum Wheels


TECHNICAL

Bulletin No.: 05-03-10-003F

Date: April 27, 2010

Subject: Low Tire Pressure, Leaking Cast Aluminum Wheels (Repair with Adhesive Sealant)

Models:

2011 and Prior GM Passenger Cars and Light Duty Trucks (Including Saturn)
2010 and Prior HUMMER H2, H3
2009 and Prior Saab 9-7X
with Cast Aluminum Wheels

Supercede:
This bulletin is being revised to update the model years and the bulletin reference information. Please discard Corporate Bulletin Number
05-03-10-003E (Section 03 - Suspension).

Condition

Some customers may comment on a low tire pressure condition.

Diagnosis of the low tire pressure condition indicates an air leak through the cast aluminum wheel.

Cause

Porosity in the cast aluminum wheel may be the cause.

Notice

This bulletin specifically addresses issues related to the wheel casting that may result in an air leak. For issues related to corrosion of the wheel in
service, please refer to Corporate Bulletin Number 08-03-10-006C - Tire Slowly Goes Flat, Tire Air Loss, Low Tire Pressure Warning Light
Illuminated, Aluminum Wheel Bead Seat Corrosion (Clean and Resurface Wheel Bead Seat).

Correction

1. Remove the tire and wheel assembly from the vehicle. Refer to the appropriate service procedure in SI.
2. Locate the leaking area by inflating the tire to 276 kPa (40 psi) and dipping the tire/wheel assembly in a water bath, or use a spray bottle with
soap and water to locate the specific leak location.

Important

- If the porosity leak is located in the bead area of the aluminum rim (where the tire meets the rim), the wheel should be replaced.
- If two or more leaks are located on one wheel, the wheel should be replaced.

3. If air bubbles are observed, mark the location.

- If the leak location is on the tire/rubber area, refer to Corporate Bulletin Number 04-03-10-001F - Tire Puncture Repair Procedures for
All Cars and Light Duty Trucks.
- If the leak is located on the aluminum wheel area, continue with the next step.

4. Inscribe a mark on the tire at the valve stem in order to indicate the orientation of the tire to the wheel.
5. Dismount the tire from the wheel. Refer to Tire Mounting and Dismounting.
6. Remove the tire pressure sensor. Refer to Tire Pressure Sensor removal procedure in SI.
7. Scuff the INSIDE rim surface at the leak area with #80 grit paper and clean the area with general purpose cleaner, such as 3M(R) General
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 140
Chevrolet Venture V6-3.4L VIN E 2465
Purpose Adhesive Cleaner, P/N 08984, or equivalent.
8. Apply a 3 mm (0.12 in) thick layer of Silicone - Adhesive/Sealant, P/N 12378478 (in Canada, use 88900041), or equivalent, to the leak area.
9. Allow for the adhesive/sealant to dry.

Notice
Caution must be used when mounting the tire so as not to damage the sealer. Damaging the repair area may result in an air leak.

10. Align the inscribed mark on the tire with the valve stem on the wheel.
11. Reinstall the Tire Pressure Sensor. Refer to Tire Pressure Sensor installation procedure in SI.
12. Mount the tire on the wheel. Refer to Tire Mounting and Dismounting.
13. Pressurize the tire to 276 kPa (40 psi) and inspect for leaks.
14. Adjust tire pressure to meet the placard specification.
15. Balance the tire/wheel assembly. Refer to Tire and Wheel Assembly Balancing - Off-Vehicle.
16. Install the tire and wheel assembly onto the vehicle. Refer to the appropriate service procedure in SI.

Parts Information

Warranty Information (excluding Saab U.S. Models)

Important
The Silicone - Adhesive/Sealant comes in a case quantity of six. ONLY charge warranty one tube of adhesive/sealant per wheel repair.

For vehicles repaired under warranty, use:

One leak repair per wheel.

Warranty Information (Saab U.S. Models)

For vehicles repaired under warranty, use the table above.

Disclaimer

Technical Service Bulletin # 08-03-10-006C Date: 100427

Tires/Wheels - Tire Slowly Goes Flat/Warning Light ON


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 141
Chevrolet Venture V6-3.4L VIN E 2466
TECHNICAL

Bulletin No.: 08-03-10-006C

Date: April 27, 2010

Subject: Tire Slowly Goes Flat, Tire Air Loss, Low Tire Pressure Warning Light Illuminated, Aluminum Wheel Bead Seat Corrosion (Clean and
Resurface Wheel Bead Seat)

Models:

2000-2011 GM Passenger Cars and Light Duty Trucks (including Saturn)


2003-2009 HUMMER H2
2006-2010 HUMMER H3
2005-2009 Saab 9-7X

Supercede:
This bulletin is being revised to update the model years. Please discard Corporate Bulletin Number 08-03-10-006B (Section 03 - Suspension).

Condition

Some customers may comment on a tire that slowly loses air pressure over a period of days or weeks.

Cause

Abrasive elements in the environment may intrude between the tire and wheel at the bead seat. There is always some relative motion between the
tire and wheel (when the vehicle is driven) and this motion may cause the abrasive particles to wear the wheel and tire materials. As the wear
continues, there may also be intrusion at the tire/wheel interface by corrosive media from the environment. Eventually a path for air develops and a
'slow' leak may ensue. This corrosion may appear on the inboard or outboard bead seating surface of the wheel. This corrosion will not be visible
until the tire is dismounted from the wheel.

Notice

This bulletin specifically addresses issues related to wheel bead seat corrosion that may result in an air leak. For issues related to porosity of the
wheel casting that may result in an air leak, please refer to Corporate Bulletin Number 05-03-10-006F - Low Tire Pressure, Leaking Cast
Aluminum Wheels (Repair with Adhesive Sealant)

Correction

In most cases, this type of air loss can be corrected by following the procedure below.

Important
DO NOT replace a wheel for slow air loss unless you have evaluated and/or tried to repair the wheel with the procedure below.

Notice

The repair is no longer advised or applicable for chromed aluminum wheels.


1. Remove the wheel and tire assembly for diagnosis. Refer to Tire and Wheel Removal and Installation in SI.
2. After a water dunk tank leak test, if you determine the source of the air leak to be around the bead seat of the wheel, dismount the tire to
examine the bead seat. Shown below is a typical area of bead seat corrosion.Typical Location of Bead Seat Corrosion

Important
Other forms of slow air leaks are possible. If the body of the tire, valve stem and wheel flange show no signs of air seepage, refer to
Corporate Bulletin Number 05-03-10-003D for additional information on possible wheel porosity issues.
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 142
Chevrolet Venture V6-3.4L VIN E 2467

3. Bead seat corrosion is identified by what appears like blistering of the wheel finish, causing a rough or uneven surface that is difficult for the
tire to maintain a proper seal on. Below is a close-up photo of bead seat corrosion on an aluminum wheel that was sufficient to cause slow air
loss. Close-Up of Bead Seat Corrosion

4. If corrosion is found on the wheel bead seat, measure the affected area as shown below.

- For vehicles with 32,186 km (20,000 mi) or less, the total allowable combined linear area of repairable corrosion is 100 mm (4 in) or less.
If the total area(s) of corrosion exceed these dimensions, the wheel should be replaced.
- For vehicles that have exceeded 32,186 km (20,000 mi), the total allowable combined linear area of repairable corrosion is 200 mm (8 in)
or less. If the total area(s) of corrosion exceed these dimensions, the wheel should be replaced.

5. In order to correct the wheel leak, use a clean-up (fine cut) sanding disc or biscuit to remove the corrosion and any flaking paint. You should
remove the corrosion back far enough until you reach material that is stable and firmly bonded to the wheel. Try to taper the edge of any
flaking paint as best you can in order to avoid sharp edges that may increase the chance of a leak reoccurring. The photo below shows an
acceptable repaired surface.

Notice
Corrosion that extends up the lip of the wheel, where after the clean-up process it would be visible with the tire mounted, is only acceptable
on the inboard flange. The inboard flange is not visible with the wheel assembly in the mounted position. If any loose coatings or corrosion
extend to the visible surfaces on the FACE of the wheel, that wheel must be replaced.

Important
Remove ONLY the material required to eliminate the corrosion from the bead seating surface. DO NOT remove excessive amounts
of material. ALWAYS keep the sealing surface as smooth and level as possible.

Acceptably Prepared (Cleaned-Up) Wheel Surface

6. Once the corrosion has been eliminated, you should coat the repaired area with a commercially available tire sealant such as Patch Brand
Bead Sealant or equivalent. Commercially available bead sealants are black rubber-like coatings that will permanently fill and seal the
resurfaced bead seat. At 21°C (70°F) ambient temperature, this sealant will set-up sufficiently for tire mounting in about 10 minutes.Coated
and Sealed Bead Seat
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 143
Chevrolet Venture V6-3.4L VIN E 2468

7. Remount the tire and install the repaired wheel and tire assembly. Refer to Tire and Wheel Removal and Installation in SI.

Parts Information

Patch Brand Bead Sealer is available from Myers Tires at 1-800-998-9897 or on the web at www.myerstiresupply.com. The one-quart size can of
sealer will repair about 20 wheels.

Warranty Information (excluding Saab U.S. Models)

For vehicles repaired under warranty, use:

Warranty Information (Saab U.S. Models)

For vehicles repaired under warranty, use the table above.

Disclaimer

Technical Service Bulletin # 00-03-10-006F Date: 100504

Wheels/Tires - Tire Radial Force Variation (RFV)


INFORMATION

Bulletin No.: 00-03-10-006F

Date: May 04, 2010

Subject: Information on Tire Radial Force Variation (RFV)

Models:

2011 and Prior GM Passenger Cars and Light Duty Trucks


2010 and Prior HUMMER H2, H3
2009 and Prior Saab 9-7X
2000-2005 Saturn L Series
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 144
Chevrolet Venture V6-3.4L VIN E 2469
2003-2007 Saturn ION

Supercede:
This bulletin is being revised to considerably expand the available information on Radial Force Variation (RFV) and should be reviewed in whole.
Please discard Corporate Bulletin Number 00-03-10-006E (Section 03 - Suspension).

Important

- Before measuring tires on equipment such as the Hunter GSP9700, the vehicle MUST be driven a minimum of 16 km (10 mi) to
ensure removal of any flat-spotting. Refer to Corporate Bulletin Number 03-03-10-007E - Tire/Wheel Characteristics of GM
Original Equipment Tires.
- Equipment such as the Hunter GSP9700 MUST be calibrated prior to measuring tire/wheel assemblies for each vehicle.

The purpose of this bulletin is to provide guidance to GM dealers when using tire force variation measurement equipment, such as the Hunter
GSP9700. This type of equipment can be a valuable tool in diagnosing vehicle ride concerns. The most common ride concern involving tire radial
force variation is highway speed shake on smooth roads.

Tire related smooth road highway speed shake can be caused by three conditions: imbalance, out of round and tire force variation. These three
conditions are not necessarily related. All three conditions must be addressed.

Imbalance is normally addressed first, because it is the simpler of the three to correct. Off-vehicle, two plane dynamic wheel balancers are readily
available and can accurately correct any imbalance. Balancer calibration and maintenance, proper attachment of the wheel to the balancer, and
proper balance weights, are all factors required for a quality balance. However, a perfectly balanced tire/wheel assembly can still be "oval shaped"
and cause a vibration.

Before balancing, perform the following procedures.

Tire and Wheel Diagnosis


1. Set the tire pressure to the placard values.
2. With the vehicle raised, ensure the wheels are centered on the hub by loosening all wheel nuts and hand-tightening all nuts first by hand
while shaking the wheel, then torque to specifications using a torque wrench, NOT a torque stick.
3. Visually inspect the tires and the wheels. Inspect for evidence of the following conditions and correct as necessary:

- Missing balance weights


- Bent rim flange
- Irregular tire wear
- Incomplete bead seating
- Tire irregularities (including pressure settings)
- Mud/ice build-up in wheel
- Stones in the tire tread
- Remove any aftermarket wheels and/or tires and restore vehicle to original condition prior to diagnosing a smooth road shake condition.

4. Road test the vehicle using the Electronic Vibration Analyzer (EVA) essential tool. Drive for a sufficient distance on a known, smooth road
surface to duplicate the condition. Determine if the vehicle is sensitive to brake apply. If the brakes are applied lightly and the pulsation felt
in the steering wheel increases, refer to the Brakes section of the service manual that deals with brake-induced pulsation. If you can start to
hear the vibration as a low boom noise (in addition to feeling it), but cannot see it, the vehicle likely has a first order (one pulse per propshaft
revolution) driveline vibration. Driveline first order vibrations are high enough in frequency that most humans can start to hear them at
highway speeds, but are too high to be able to be easily seen. These issues can be caused by driveline imbalance or misalignment. If the
vehicle exhibits this low boom and the booming pulses in-and-out on a regular basis (like a throbbing), chances are good that the vehicle
could have driveline vibration. This type of vibration is normally felt more in the "seat of the pants" than the steering wheel.
5. Next, record the Hertz (Hz) reading as displayed by the EVA onto the tire data worksheet found at the end of this bulletin. This should be
done after a tire break-in period of at least 16 km (10 mi) at 72 km/h (45 mph) or greater, in order to eliminate any possible tire flat-spotting.
This reading confirms what the vehicle vibration frequency is prior to vehicle service and documents the amount of improvement occurring
as the result of the various steps taken to repair. Completing the Steering Wheel Shake Worksheet below is required. A copy of the
completed worksheet must be saved with the R.O. and a copy included with any parts returned to the Warranty Parts Center for analysis. A
reading of 35 to 50 Hz typically indicates a first order propshaft vibration. If this is the situation, refer to Corporate Bulletin Number
08-07-30-044D. Generally, a reading between 10 and 20 Hz indicates a tire/wheel vibration and if this is the reading obtained, continue using
this bulletin.
If the tire 1st order vibration goes away and stays away during this evaluation, the cause is likely tire flat-spotting. Tire flat-spotting vibration
may come and go at any speed over 72 km/h (45 mph) during the first 10 minutes of operation, if vibration continues after 10 minutes of
driving at speeds greater than 72 km/h (45 mph), tire flat-spotting can be ruled out as the cause for vibration.
6. If flat-spotting is the cause, provide the explanation that this has occurred due to the vehicle being parked for long periods of time and that
the nature of the tire is to take a set. Refer to Corporate Bulletin Number 03-03-10-007E: Information on Tire/Wheel Characteristics
(Vibration, Balance, Shake, Flat Spotting) of GM Original Equipment Tires.
7. If the road test indicates a shake/vibration exists, check the imbalance of each tire/wheel assembly on a known, calibrated, off-car dynamic
balancer.Make sure the mounting surface of the wheel and the surface of the balancer are absolutely clean and free of debris. Be sure
to chose the proper cone/collet for the wheel, and always use the pilot bore for centering. Never center the wheel using the hub-cap
bore since it is not a precision machined surface. If any assembly calls for more than 1/4 ounce on either rim flange, remove all balance
weights and rebalance to as close to zero as possible. If you can see the vibration (along with feeling it) in the steering wheel (driving straight
without your hands on the wheel), it is very likely to be a tire/wheel first order (one pulse per revolution) disturbance. First order disturbances
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 145
Chevrolet Venture V6-3.4L VIN E 2470
can be caused by imbalance as well as non-uniformities in tires, wheels or hubs. This first order frequency is too low for a human to hear, but
if the amplitude is high enough, it can be seen.

If a vibration or shake still exists after balancing, any out of round conditions, of the wheel, and force variation conditions of the tire, must be
addressed. Equipment such as the Hunter GSP9700 can address both (it is also a wheel balancer).

Tire radial force vibration (RFV) can be defined as the amount of stiffness variation the tire will produce in one revolution under a constant load.
Radial force variation is what the vehicle feels because the load (weight) of the vehicle is always on the tires. Although free runout of tires (not
under load) is not always a good indicator of a smooth ride, it is critical that total tire/wheel assembly runout be within specification.

Equipment such as the Hunter GSP9700 loads the tire, similar to on the vehicle, and measures radial force variation of the tire/wheel assembly.
Note that the wheel is affecting the tire's RFV measurement at this point. To isolate the wheel, its runout must be measured. This can be easily done
on the Hunter, without the need to set up dial indicators. If the wheel meets the runout specification, the tire's RFV can then be addressed.

After measuring the tire/wheel assembly under load, and the wheel alone, the machine then calculates (predicts) the radial force variation of the tire.
However, because this is a prediction that can include mounting inaccuracies, and the load wheel is much smaller in diameter than used in tire
production, this type of service equipment should NOT be used to audit new tires. Rather, it should be used as a service diagnostic tool to minimize
radial force variation of the tire/wheel assembly.

Equipment such as the Hunter GSP9700 does an excellent job of measuring wheel runout, and of finding the low point of the wheel (for runout)
and the high point of the tire (for radial force variation). This allows the tire to be matched mounted to the wheel for lowest tire/wheel assembly
force variation.

The machine will simplify this process into easy steps. The following assembly radial force variation numbers should be used as a guide:

When measuring RFV and match mounting tires perform the following steps.

Measuring Wheel Runout and Assembly Radial Force Variation

Important
The completed worksheet at the end of this bulletin must be attached to the hard copy of the repair order.

- Measure radial force variation and radial runout.


- If a road force/balancing machine is used, record the radial force variation (RFV) on the worksheet at the end of this bulletin. It may be of
benefit to have the lowest RFV assembly to the front left corner. If the machine is not available and the EVA data suggests there is an issue,
swap the tire and wheel assemblies from the front to the back. Re-check on the EVA and if the problem still exists, test another vehicle to
find tires that do not exhibit the same frequency and swap those tires onto the subject vehicle.
- If a runout/balancing machine is used, record the radial runout of the tire/wheel assemblies on the worksheet at the end of this bulletin. If one
or more of the tire/wheel assemblies are more than.040 in (1.02 mm), match mount the tire to the wheel to get below.040 in (1.02 mm). For
sensitive customers, readings of 0.030 inch (0.76 mm) or less are preferable, it may also be of benefit to have the lowest runout assembly to
the front left corner. If the machine is not available and the EVA data suggests there is an issue, swap the tire and wheel assemblies from the
front to the back. Re-check on the EVA and if the problem still exists, test another vehicle to find tires that do not exhibit the same frequency
and swap those tires onto the subject vehicle.
- After match mounting, the tire/wheel assembly must be rebalanced.
If match mounting tires to in-spec wheels produces assembly values higher than these, tire replacement may be necessary. Replacing tires at lower
values will probably mean good tires are being condemned. Because tires can sometimes become temporarily flat-spotted, which will affect force
variation, it is important that the vehicle be driven at least 16 km (10 mi) prior to measuring. Tire pressure must also be adjusted to the usage
pressure on the vehicle's tire placard prior to measuring.

Most GM vehicles will tolerate radial force variation up to these levels. However, some vehicles are more sensitive, and may require lower levels.
Also, there are other tire parameters that equipment such as the Hunter GSP9700 cannot measure that may be a factor. In such cases, TAC should
be contacted for further instructions.

Important

- When mounting a GM wheel to a wheel balancer/force variation machine, always use the wheel's center pilot hole. This is the
primary centering mechanism on all GM wheels; the bolt holes are secondary. Usually a back cone method to the machine should be
used. For added accuracy and repeatability, a flange plate should be used to clamp the wheel onto the cone and machine. This system
is offered by all balancer manufacturers in GM's dealer program.
- Any type of service equipment that removes tread rubber by grinding, buffing or truing is NOT recommended, and may void the tire
warranty. However, tires may have been ground by the tire company as part of their tire manufacturing process. This is a legitimate
procedure.

Steering Wheel Shake Worksheet


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 146
Chevrolet Venture V6-3.4L VIN E 2471

When diagnosing vibration concerns, use the following worksheet in conjunction with the appropriate Vibration Analysis-Road testing procedure
in the Vibration Correction sub-section in SI.

Refer to the appropriate section of SI for specifications and repair procedures that are related to the vibration concern.

Disclaimer
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 147
Chevrolet Venture V6-3.4L VIN E 2472

Technical Service Bulletin # 00-01-38-001 Date: 000101

A/C - Lack of Performance in Hot/Humid Weather


BULLETIN NUMBER:
00-01-38-001

SECTION:
01 - HVAC

DATE:
January, 2000

TITLE:
HVAC Lack of Performance - Single A/C System Only (Evacuate & Recharge A/C System)

MODELS:
1998-2000 Chevrolet Venture
1998-2000 Oldsmobile Silhouette
1998-2000 Pontiac Trans Sport
With C60 Air Conditioner Frt, Manual Controls (Not C34)
Built from SOP thru VIN Breakpoint YD150489 for 2000 Models Only

CONDITION:
Some customers may comment on a lack of performance of the air conditioning system in hot, humid weather.

CAUSE:
This condition may be due to an undercharged air conditioning system during the vehicle assembly process.

CORRECTION:
1. Perform the Cooling Insufficient, A/C System check. Refer to the HVAC Systems-Manual sub-section of the Service Manual. If a condition
is identified, make the appropriate repair. If no abnormal condition is identified, proceed to the next step.

2. Evacuate and recharge the A/C system with 1.08 kg (2.375 lbs) of R-134a.

3. Replace the A/C evaporator label with P/N 10443319. This label will allow future service technicians to know how much refrigerant is
required by the system.

4. Inspect/test the A/C system for signs of leaks, both visually and with the A/C leak tester.

5. If a leak is found, perform the recommended repair. Refer to the HVAC Systems-Manual sub-section of the Service Manual.

6. If no leaks are found, perform the Cooling Insufficient, A/C System check. Refer to the HVAC Systems-Manual sub-section of the Service
Manual. If a condition is identified, make the appropriate repair. If no abnormal condition is identified, return the vehicle to the owner.

PARTS INFORMATION

Parts are currently available from GMSPO.

WARRANTY INFORMATION

For vehicles repaired under warranty, use chart:

*The 0.6 hr includes the time required to install the new label.

If an evacuate and recharge was required, add 0.9 hr to the base time for evacuating and recharging the HVAC System.

This is a unique Labor Operation Number for use only with this bulletin. This number will not be published in the Labor Time Guide.

Technical Service Bulletin # 00-08-64-007 Date: 000601

Front Door Window - Inoperative/Slow or Noisy


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 148
Chevrolet Venture V6-3.4L VIN E 2473
File In Section: 08 Body and Accessories

Bulletin No.: 00-08-64-007

Date: June, 2000

TECHNICAL

Subject:
Slow/Non-Moving (Chatters/Noisy) Glass, Bent Regulator Arms or Window is inoperative (Replace Run Channel and/or Weatherstrip)

Models:
1997-2000 Chevrolet Venture
1997-2000 Oldsmobile Silhouette
1997-1999 Pontiac Trans Sport
1999-2000 Pontiac Montana

Condition

Some customers may comment that the front door glass is slow or noisy when moving up or down or the window is inoperative.

Cause

The window run channel may be adjusted improperly which may cause the following:

^ The glass may be slow/non-moving.

^ The glass wears through the flocking on the weatherstrip and allows direct contact between the glass and the rubber of the weatherstrip, which
causes drag.

^ Bent regulator arms may be due to glass drag from the run window channel.

Correction

Adjust the window run channel upper attachment full forward and the lower attachment full rearward. Replace run channel and/or weatherstrip, if
necessary.

Parts Information

Parts are expected to be available from GMSPO, 6/5/00.

Warranty Information

For vehicles repaired under warranty, use the table.


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 149
Chevrolet Venture V6-3.4L VIN E 2474

Disclaimer
Procedure
1. Remove the door switch plate.

2. Disconnect the electrical connectors from the switch plate.

3. Remove the bezel behind the door handle.

4. Remove the bolts from the armrest.

5. Remove the trim panel retainers and remove the trim panel.

6. Remove the water deflector.

7. Remove the inner belt seal.

8. Remove the outer belt seal.

9. Raise the glass to gain access to the lower sash channel retaining clips. Push in on the retainers and slide the sash channel to release the glass.

10. Remove the glass from the door.

11. Remove the weatherstrip from the run channel.

12. Remove the bolts from the run channel and remove the run channel from the door.

13. Loosen the mirror for weatherstrip removal.

14. Remove the weatherstrip from the door.

15. Spray the backside of the new weatherstrip with window cleaner for ease of installation and install the weatherstrip.

16. Tighten the mirror retaining nuts.

Tighten
Tighten the nuts to 10 Nm (89 lb in).

17. Install the window run channel in the door and leave the retaining bolts finger tight.

18. With the window run channel installed, move the upper attachment full forward and the lower attachment full rearward.

Tighten
Tighten to 10 Nm (89 lb in).

19. Install the weatherstrip in the window lower run channel.

20. Install the glass door.

21. Install the outer belt seal.

22. Install the inner belt seal.

23. Install the water deflector using a 50.8 mm (2 in) wallpaper roller. Starting at the bottom center and working outboard, roll out the butyle
adhesive up the right and left sides. A 50.8 mm (2 in) roller can be purchased at a hardware or wallpaper store.

24. Install the trim panel.

25. Install the door trim panel bolts. Tighten

Tighten the bolts to 3 Nm (26 lb in).

26. Attach the electrical connectors to the switch and install the switch.

27. Install the door handle bezel.Technical Service Bulletin # 08-07-30-035A Date: 100101
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 150
Chevrolet Venture V6-3.4L VIN E 2475

08-07-30-035A - 01/01/2010
This TSB number 08-07-30-035A, dated 01/01/10 has been superceded by TSB number 08-07-30-035B , dated 11/01/10
Technical Service Bulletin # 05-06-04-022F Date: 101001

05-06-04-022F - 10/01/10
This TSB number 05-06-04-022F, dated 10/01/10 has been superceded by TSB number 05-06-04-022G , dated 10/27/10
Technical Service Bulletin # 00-07-30-009B Date: 091101

00-07-30-009B - 11/01/09
This TSB number 00-07-30-009B, dated 11/01/09 has been superceded by TSB number 00-07-30-009D , dated 02/24/10
Technical Service Bulletin # 06-08-64-001 Date: 061201

06-08-64-001 - 12/01/06
This TSB number 06-08-64-001, dated 12/01/06 has been superceded by TSB number 06-08-64-001B , dated 10/20/09
Technical Service Bulletin # 06-08-64-001A Date: 091001

06-08-64-001A - 10/01/09
This TSB number 06-08-64-001A, dated 10/01/09 has been superceded by TSB number 06-08-64-001B , dated 10/20/09
Technical Service Bulletin # 05-03-08-002 Date: 051201

05-03-08-002 - 12/01/05
This TSB number 05-03-08-002, dated 12/01/05 has been superceded by TSB number 05-03-08-002C , dated 10/16/09
Technical Service Bulletin # 05-03-08-002A Date: 081019

05-03-08-002A - 10/19/08
This TSB number 05-03-08-002A, dated 10/19/08 has been superceded by TSB number 05-03-08-002C , dated 10/16/09
Technical Service Bulletin # 05-03-08-002B Date: 091001

05-03-08-002B - 10/01/09
This TSB number 05-03-08-002B, dated 10/01/09 has been superceded by TSB number 05-03-08-002C , dated 10/16/09
Technical Service Bulletin # 06-00-89-051B Date: 081201

06-00-89-051B - 12/01/08
This TSB number 06-00-89-051B, dated 12/01/08 has been superceded by TSB number 10-00-89-010 , dated 05/27/10
Technical Service Bulletin # 06-08-64-007 Date: 061201

06-08-64-007 - 12/01/06
This TSB number 06-08-64-007, dated 12/01/06 has been superceded by TSB number 06-08-64-007A , dated 09/22/08
Technical Service Bulletin # 04-07-30-017 Date: 080101

04-07-30-017 - 01/01/08
This TSB number 04-07-30-017, dated 01/01/08 has been superceded by TSB number 04-07-30-017B , dated 11/25/08
Technical Service Bulletin # 04-06-04-036D Date: 080401

04-06-04-036D - 04/01/08
This TSB number 04-06-04-036D, dated 04/01/08 has been superceded by TSB number 04-06-04-036E , dated 05/08/08
Technical Service Bulletin # 04-08-50-006 Date: 040601

04-08-50-006 - 06/01/04
This TSB number 04-08-50-006, dated 06/01/04 has been superceded by TSB number 04-08-50-006D , dated 09/09/10
Technical Service Bulletin # 04-08-50-006A Date: 071201

04-08-50-006A - 12/01/07
This TSB number 04-08-50-006A, dated 12/01/07 has been superceded by TSB number 04-08-50-006D , dated 09/09/10
Technical Service Bulletin # 04-06-04-054 Date: 070101

04-06-04-054 - 01/01/07
This TSB number 04-06-04-054, dated 01/01/07 has been superceded by TSB number 04-06-04-054A , dated 01/11/07
Technical Service Bulletin # 03-08-48-006 Date: 060101
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 151
Chevrolet Venture V6-3.4L VIN E 2476
03-08-48-006 - 01/01/06
This TSB number 03-08-48-006, dated 01/01/06 has been superceded by TSB number 03-08-48-006G , dated 02/26/10
Technical Service Bulletin # 03-07-30-043 Date: 060501

03-07-30-043 - 05/01/06
This TSB number 03-07-30-043, dated 05/01/06 has been superceded by TSB number 03-07-30-043A , dated 05/25/06
Technical Service Bulletin # 05-06-04-013 Date: 050101

05-06-04-013 - 01/01/05
This TSB number 05-06-04-013, dated 01/01/05 has been superceded by TSB number 04-06-04-036E , dated 05/08/08
Technical Service Bulletin # 43-17-01 Date: 050901

43-17-01 - 09/0/05
This TSB number 43-17-01, dated 09/01/05 has been superceded by TSB number 05-08-51-008C , dated 06/22/09
Technical Service Bulletin # 43-17-01A Date: 051001

43-17-01A - 10/01/05
This TSB number 43-17-01A, dated 10/01/05 has been superceded by TSB number 05-08-51-008C , dated 06/22/09
Technical Service Bulletin # 43-17-01B Date: 051019

43-17-01B - 10/19/05
This TSB number 43-17-01B, dated 10/19/05 has been superceded by TSB number 05-08-51-008C , dated 06/22/09
Technical Service Bulletin # 00-06-01-012A Date: 050208

00-06-01-012A - 02/08/05
This TSB number 00-06-01-012A, dated 02/08/05 has been superceded by TSB number 00-06-01-012C , dated 04/14/08
Technical Service Bulletin # 02-01-39-004 Date: 020112

02-01-39-004 - 01/12/02
This TSB number 02-01-39-004, dated 01/12/02 has been superceded by TSB number 02-01-39-004B , dated 11/16/05
Technical Service Bulletin # 00-06-04-033 Date: 000617

00-06-04-033 - 06/17/00
This TSB number 00-06-04-033, dated 06/17/00 has been superceded by TSB number 00-06-04-033B , dated 10/10/06
Technical Service Bulletin # 01-08-51-004A Date: 050701

01-08-51-004A - 07/01/05
This TSB number 01-08-51-004A, dated 07/01/05 has been superceded by TSB number 01-08-51-004E , dated 12/22/06
Technical Service Bulletin # 02-07-30-001B Date: 050501

02-07-30-001B - 05/01/05
This TSB number 02-07-30-001B, dated 05/01/05 has been superceded by TSB number 02-07-30-001G , dated 03/19/08
Technical Service Bulletin # 01-08-45-005B Date: 050401

01-08-45-005B - 04/01/05
This TSB number 01-08-45-005B, dated 04/01/05 has been superceded by TSB number 01-08-45-005E , dated 08/29/06
Technical Service Bulletin # 02-06-03-011 Date: 020601

02-06-03-011 - 06/01/02
This TSB number 02-06-03-011, dated 06/01/02 has been superceded by TSB number 05-06-03-002C , dated 04/17/08
Technical Service Bulletin # 01-08-46-008B Date: 050101

01-08-46-008B - 01/01/05
This TSB number 01-08-46-008B, dated 01/01/05 has been superceded by TSB number 01-08-46-008D , dated 01/15/08
Technical Service Bulletin # 99-08-44-001A Date: 010301

99-08-44-001A - 03/01/01
This TSB number 99-08-44-001A, dated 03/01/01 has been superceded by TSB number 99-08-44-001B , dated 03/01/01
Technical Service Bulletin # 99-07-30-016 Date: 020901

99-07-30-016 - 09/01/02
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 152
Chevrolet Venture V6-3.4L VIN E 2477
This TSB number 99-07-30-016, dated 09/01/02 has been superceded by TSB number 99-07-30-016B , dated 10/01/02
Technical Service Bulletin # 73-90-23 Date: 000101

73-90-23 - 01/01/00
This TSB number 73-90-23, dated 01/01/00 has been superceded by TSB number 99-09-41-004 , dated 01/01/00
Technical Service Bulletin # 73-90-12 Date: 000101

73-90-12 - 01/01/00
This TSB number 73-90-12, dated 01/01/00 has been superceded by TSB number 99-09-41-004 , dated 01/01/00
Technical Service Bulletin # 40-05-01C Date: 991001

40-05-01C - 10/01/99
This TSB number 40-05-01C, dated 10/01/99 has been superceded by TSB number 99-00-89-019B , dated 02/01/02
Technical Service Bulletin # 04-06-04-047B Date: 041201

04-06-04-047B - 12/01/04
This TSB number 04-06-04-047B, dated 12/01/04 has been superceded by TSB number 04-06-04-047I , dated 08/17/09
Technical Service Bulletin # 00-07-30-022A Date: 041101

00-07-30-022A - 11/01/04
This TSB number 00-07-30-022A, dated 11/01/04 has been superceded by TSB number 00-07-30-022D , dated 06/10/08
Technical Service Bulletin # 02-08-48-001 Date: 031202

02-08-48-001 - 12/02/03
This TSB number 02-08-48-001, dated 12/02/03 has been superceded by TSB number 02-08-48-001B , dated 03/29/06
Technical Service Bulletin # 02-07-30-052A Date: 030207

02-07-30-052A - 02/07/03
This TSB number 02-07-30-052A, dated 02/07/03 has been superceded by TSB number 02-07-30-052F , dated 09/09/09
Technical Service Bulletin # 01-08-46-008 Date: 011101

01-08-46-008 - 11/01/01
This TSB number 01-08-46-008, dated 11/01/01 has been superceded by TSB number 01-08-46-008D , dated 01/15/08
Technical Service Bulletin # 00-08-64-015 Date: 010201

00-08-64-015 - 02/01/01
This TSB number 00-08-64-015, dated 02/01/01 has been superceded by TSB number 00-08-64-015A , dated 02/01/01
Technical Service Bulletin # 00-00-89-008B Date: 031101

00-00-89-008B - 11/01/03
This TSB number 00-00-89-008B, dated 11/01/03 has been superceded by TSB number 00-00-89-008F , dated 07/28/06
Technical Service Bulletin # 99-00-89-019A Date: 001201

Warranty - Parts Return Programs


This TSB number 99-00-89-019A, dated 12/01/00 has been superceded by TSB number 99-00-89-019B , dated 02/01/02
Technical Service Bulletin # 99-00-84-021A Date: 000301

Warranty - Expediting parts


This TSB number 99-00-84-021A, dated 03/01/00 has been superceded by TSB number 99-00-84-021B , dated 04/01/00
Technical Service Bulletin # 99-00-89-019 Date: 991001

Warranty - Parts Returning Program


This TSB number 99-00-89-019, dated 10/01/99 has been superceded by TSB number 99-00-89-019B , dated 02/01/02
Technical Service Bulletin # 99-00-84-021 Date: 991101

Warranty - Expediting Parts


This TSB number 99-00-84-021, dated 11/01/99 has been superceded by TSB number 99-00-84-021B , dated 04/01/00
Technical Service Bulletin # 99-05-25-003 Date: 990901

Brakes - ABS Exchange Program


This TSB number 99-05-25-003, dated 09/01/99 has been superceded by TSB number 99-05-25-003A , dated 10/01/00
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 153
Chevrolet Venture V6-3.4L VIN E 2478
Technical Service Bulletin # 06-08-43-003A Date: 070608

Wipers - Performance/Cleaning Instructions/Maintenance


This TSB number 06-08-43-003A, dated 06/08/07 has been superceded by TSB number 06-08-43-003B , dated 11/11/09
Technical Service Bulletin # 06-08-43-003 Date: 060630

Windshield Wipers - Performance/Cleaning and Maintenance


This TSB number 06-08-43-003, dated 06/30/06 has been superceded by TSB number 06-08-43-003B , dated 11/11/09
Technical Service Bulletin # 00-08-48-005A Date: 040901

Body - Distortion in Outer Surface of Vehicle Glass


This TSB number 00-08-48-005A, dated 09/01/04 has been superceded by TSB number 00-08-48-005D , dated 09/10/10
Technical Service Bulletin # 02-08-48-001A Date: 031202

Windows/Glass - Urethane Adhesive Usage


This TSB number 02-08-48-001A, dated 12/02/03 has been superceded by TSB number 02-08-48-001B , dated 03/29/06
Technical Service Bulletin # 00-08-48-005B Date: 060912

Body - Distortion On Outer Glass Surfaces


This TSB number 00-08-48-005B, dated 09/12/06 has been superceded by TSB number 00-08-48-005D , dated 09/10/10
Technical Service Bulletin # 00-08-48-005 Date: 001201

Glass - Distortion Explanation


This TSB number 00-08-48-005, dated 12/01/00 has been superceded by TSB number 00-08-48-005D , dated 09/10/10
Technical Service Bulletin # 04-08-48-001A Date: 050119

A/C - Rear Defogger Heating Grid Damage Detection


This TSB number 04-08-48-001A, dated 01/19/05 has been superceded by TSB number 04-08-48-001B , dated 06/28/05
Technical Service Bulletin # 03-08-48-006F Date: 090526

A/C - Window Defroster Contact/Tab Repair Information


This TSB number 03-08-48-006F, dated 05/26/09 has been superceded by TSB number 03-08-48-006G , dated 02/26/10
Technical Service Bulletin # 03-08-48-006E Date: 080825

A/C - Rear Window Defroster Grid Contact/Tab Repair


This TSB number 03-08-48-006E, dated 08/25/08 has been superceded by TSB number 03-08-48-006G , dated 02/26/10
Technical Service Bulletin # 03-08-48-006D Date: 080311

Electrical, A/C - Rear Defroster Grid Repair Information


This TSB number 03-08-48-006D, dated 03/11/08 has been superceded by TSB number 03-08-48-006G , dated 02/26/10
Technical Service Bulletin # 03-08-48-006B Date: 070912

A/C - Rear Window Defroster Grid Repair Information


This TSB number 03-08-48-006B, dated 09/12/07 has been superceded by TSB number 03-08-48-006G , dated 02/26/10
Technical Service Bulletin # 03-08-48-006A Date: 061108

A/C - Rear Window Defroster Tab Repair


This TSB number 03-08-48-006A, dated 11/08/06 has been superceded by TSB number 03-08-48-006G , dated 02/26/10
Technical Service Bulletin # 04-08-48-001 Date: 040109

A/C - Broken Defogger Grid Detection


This TSB number 04-08-48-001, dated 01/09/04 has been superceded by TSB number 04-08-48-001B , dated 06/28/05
Technical Service Bulletin # 01-08-42-001E Date: 071105

Lighting - Exterior Lamp Condensation/Replacement


This TSB number 01-08-42-001E, dated 11/05/07 has been superceded by TSB number 01-08-42-001G , dated 05/04/09
Technical Service Bulletin # 01-08-42-001 Date: 010201

Exterior Lamps - Condensation & Replacement Guidelines


This TSB number 01-08-42-001, dated 02/01/01 has been superceded by TSB number 01-08-42-001G , dated 05/04/09
Technical Service Bulletin # 08-08-42-005A Date: 081217
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 154
Chevrolet Venture V6-3.4L VIN E 2479

Lighting - Headlamp Replacement Guidelines


This TSB number 08-08-42-005A, dated 12/17/08 has been superceded by TSB number 08-08-42-005B , dated 06/11/09
Technical Service Bulletin # 02-08-42-001C Date: 080905

Lighting - Headlamp Polycarbonate Lens Damage Prevention


This TSB number 02-08-42-001C, dated 09/05/08 has been superceded by TSB number 02-08-42-001D , dated 06/21/10
Technical Service Bulletin # 02-08-42-001B Date: 041008

Lighting - Damage To Polycarbonate Headlamp Lenses


This TSB number 02-08-42-001B, dated 10/08/04 has been superceded by TSB number 02-08-42-001D , dated 06/21/10
Technical Service Bulletin # 02-08-42-001A Date: 030301

Lighting - Polycarbonate Headlamp Damage Prevention


This TSB number 02-08-42-001A, dated 03/01/03 has been superceded by TSB number 02-08-42-001D , dated 06/21/10
Technical Service Bulletin # 02-08-42-001 Date: 020301

Polycarbonate Headlamp - Chemical Damage


This TSB number 02-08-42-001, dated 03/01/02 has been superceded by TSB number 02-08-42-001D , dated 06/21/10
Technical Service Bulletin # 01-08-42-001B Date: 050211

Lighting - Replacement Guidelines for Condensation


This TSB number 01-08-42-001B, dated 02/11/05 has been superceded by TSB number 01-08-42-001G , dated 05/04/09
Technical Service Bulletin # 01-08-42-001A Date: 031104

Lighting - Lamp Condensation/Replacement Guidelines


This TSB number 01-08-42-001A, dated 11/04/03 has been superceded by TSB number 01-08-42-001G , dated 05/04/09
Technical Service Bulletin # 03-08-42-007 Date: 030804

Lighting - Tail/Brake Lamp Bulb(s) Inoperative


This TSB number 03-08-42-007, dated 08/04/03 has been superceded by TSB number 03-08-42-007A , dated 01/09/04
Technical Service Bulletin # 01-08-42-001F Date: 080502

Lighting - Exterior Lamp Condensation Guideline


This TSB number 01-08-42-001F, dated 05/02/08 has been superceded by TSB number 01-08-42-001G , dated 05/04/09
Technical Service Bulletin # 01-08-42-001D Date: 061030

Lighting - Replacement Guidelines for Lamp Condensation


This TSB number 01-08-42-001D, dated 10/30/06 has been superceded by TSB number 01-08-42-001G , dated 05/04/09
Technical Service Bulletin # 01-08-42-001C Date: 050519

Exterior Lamps - Condensation Replacement Guidelines


This TSB number 01-08-42-001C, dated 05/19/05 has been superceded by TSB number 01-08-42-001G , dated 05/04/09
Technical Service Bulletin # 02-08-42-004 Date: 020401

A/T - PRNDL Display Dim for One Minute


This TSB number 02-08-42-004, dated 04/01/02 has been superceded by TSB number 02-08-42-004A , dated 03/30/07
Technical Service Bulletin # 03-00-89-008D Date: 071102

Body - Metal Body Panel Corrosion Protection


This TSB number 03-00-89-008D, dated 11/02/07 has been superceded by TSB number 03-00-89-008E , dated 07/01/10
Technical Service Bulletin # 03-00-89-008C Date: 070524

Body - Metal Panel Corrosion Protection


This TSB number 03-00-89-008C, dated 05/24/07 has been superceded by TSB number 03-00-89-008E , dated 07/01/10
Technical Service Bulletin # 07-08-98-001 Date: 070402

Body - Non-Approval of 'Clipping' for Collision Repair


This TSB number 07-08-98-001, dated 04/02/07 has been superceded by TSB number 07-08-98-001A , dated 01/28/09
Technical Service Bulletin # 02-08-98-002B Date: 070117
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 155
Chevrolet Venture V6-3.4L VIN E 2480
Body - Hem Flange Repair
This TSB number 02-08-98-002B, dated 01/17/07 has been superceded by TSB number 02-08-98-002C , dated 02/03/09
Technical Service Bulletin # 02-08-67-006A Date: 021201

Body - Roof Rust Perforation


This TSB number 02-08-67-006A, dated 12/01/02 has been superceded by TSB number 02-08-67-006B , dated 03/01/03
Technical Service Bulletin # 02-08-67-006 Date: 020601

Body - Rear Roof Rust Formation/Perforation


This TSB number 02-08-67-006, dated 06/01/02 has been superceded by TSB number 02-08-67-006B , dated 03/01/03
Technical Service Bulletin # 99-08-64-016A Date: 030101

Body - Weatherstrip Maintenance


This TSB number 99-08-64-016A, dated 01/01/03 has been superceded by TSB number 99-08-64-016C , dated 07/29/09
Technical Service Bulletin # 99-08-64-016 Date: 990901

Weatherstrips - Use of Silicone Grease for Maintenance


This TSB number 99-08-64-016, dated 09/01/99 has been superceded by TSB number 99-08-64-016C , dated 07/29/09
Technical Service Bulletin # 02-08-58-005A Date: 040114

Body - Wind Noise From Base of Windshield


This TSB number 02-08-58-005A, dated 01/14/04 has been superceded by TSB number 02-08-58-005B , dated 02/09/05
Technical Service Bulletin # 02-08-58-005 Date: 020601

Body - Wind Noise at Base of Windshield


This TSB number 02-08-58-005, dated 06/01/02 has been superceded by TSB number 02-08-58-005B , dated 02/09/05
Technical Service Bulletin # 04-08-50-006C Date: 090827

Interior - Seat Cover Wrinkle/Crease/Burn Info


This TSB number 04-08-50-006C, dated 08/27/09 has been superceded by TSB number 04-08-50-006D , dated 09/09/10
Technical Service Bulletin # 04-08-50-006B Date: 080125

Interior - Seat Cover Wrinkle/Crease/Crack/Burn Info.


This TSB number 04-08-50-006B, dated 01/25/08 has been superceded by TSB number 04-08-50-006D , dated 09/09/10
Technical Service Bulletin # 05-08-51-008B Date: 070423

Body -Bumps or Rust Colored Spots in Paint


This TSB number 05-08-51-008B, dated 04/23/07 has been superceded by TSB number 05-08-51-008C , dated 06/22/09
Technical Service Bulletin # 05-08-51-008A Date: 060517

Body - Bumps/Rust Colored Spots in Paint


This TSB number 05-08-51-008A, dated 05/17/06 has been superceded by TSB number 05-08-51-008C , dated 06/22/09
Technical Service Bulletin # 05-08-51-008 Date: 051122

Body - Rust Colored Spots in Paint


This TSB number 05-08-51-008, dated 11/22/05 has been superceded by TSB number 05-08-51-008C , dated 06/22/09
Technical Service Bulletin # 07-08-64-022A Date: 080605

Instruments - Door Mirror Diagnostic Information


This TSB number 07-08-64-022A, dated 06/05/08 has been superceded by TSB number 07-08-64-022B , dated 01/06/09
Technical Service Bulletin # 08-08-64-011 Date: 080623

Mirrors - Heated Mirror Defrosting Time


This TSB number 08-08-64-011, dated 06/23/08 has been superceded by TSB number 08-08-64-011A , dated 02/26/10
Technical Service Bulletin # 06-00-89-051C Date: 090211

Locks - Key Code Security Rules And Information


This TSB number 06-00-89-051C, dated 02/11/09 has been superceded by TSB number 10-00-89-010 , dated 05/27/10
Technical Service Bulletin # 06-00-89-051A Date: 070124

Locks - Key Code Securtiy Rules & Information


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 156
Chevrolet Venture V6-3.4L VIN E 2481
This TSB number 06-00-89-051A, dated 01/24/07 has been superceded by TSB number 10-00-89-010 , dated 05/27/10
Technical Service Bulletin # 07-08-64-022 Date: 071213

Instruments - O/S Rearview Mirror Diagnostics


This TSB number 07-08-64-022, dated 12/13/07 has been superceded by TSB number 07-08-64-022B , dated 01/06/09
Technical Service Bulletin # 00-00-89-027B Date: 040721

Interior - Odor Elimination


This TSB number 00-00-89-027B, dated 07/21/04 has been superceded by TSB number 00-00-89-027E , dated 09/29/08
Technical Service Bulletin # 03-08-98-002A Date: 041011

Body - Squeeze Type Resistance Spot Welding/Equipment


This TSB number 03-08-98-002A, dated 10/11/04 has been superceded by TSB number 03-08-98-002B , dated 06/30/10
Technical Service Bulletin # 03-00-89-008B Date: 040127

Body - Corrosion Protection for Metal Panels


This TSB number 03-00-89-008B, dated 01/27/04 has been superceded by TSB number 03-00-89-008E , dated 07/01/10
Technical Service Bulletin # 02-08-98-002A Date: 041011

Body - Information ON Hem Flange Repair


This TSB number 02-08-98-002A, dated 10/11/04 has been superceded by TSB number 02-08-98-002C , dated 02/03/09
Technical Service Bulletin # 02-08-98-001B Date: 050902

Body - Information On Metal Bonding


This TSB number 02-08-98-001B, dated 09/02/05 has been superceded by TSB number 02-08-98-001C , dated 10/09/06
Technical Service Bulletin # 06-08-111-004A Date: 080915

Body - Exterior Emblem Discoloration/Blistering/Peeling


This TSB number 06-08-111-004A, dated 09/15/08 has been superceded by TSB number 06-08-111-004B , dated 09/25/09
Technical Service Bulletin # 06-08-111-004 Date: 060908

Body - Exterior Emblem Discoloration/Peeling/Blistering


This TSB number 06-08-111-004, dated 09/08/06 has been superceded by TSB number 06-08-111-004B , dated 09/25/09
Technical Service Bulletin # 00-00-89-027 Date: 001101

Interior - Odor Elimination Product


This TSB number 00-00-89-027, dated 11/01/00 has been superceded by TSB number 00-00-89-027E , dated 09/29/08
Technical Service Bulletin # 01-08-51-004D Date: 060605

Body - Premature Aluminum Hood Corrosion/Blistering


This TSB number 01-08-51-004D, dated 06/05/06 has been superceded by TSB number 01-08-51-004E , dated 12/22/06
Technical Service Bulletin # 01-08-51-004C Date: 051202

Body - Premature Aluminum Hood Corrosion


This TSB number 01-08-51-004C, dated 12/02/05 has been superceded by TSB number 01-08-51-004E , dated 12/22/06
Technical Service Bulletin # 01-08-51-004B Date: 050801

Body - Premature Aluminum Hood Blistering/Corrosion


This TSB number 01-08-51-004B, dated 08/01/05 has been superceded by TSB number 01-08-51-004E , dated 12/22/06
Technical Service Bulletin # 01-08-51-004 Date: 011001

Hood (Aluminum) - Blistering or Bubbling Paint


This TSB number 01-08-51-004, dated 10/01/01 has been superceded by TSB number 01-08-51-004E , dated 12/22/06
Technical Service Bulletin # 00-08-48-005C Date: 080201

Body - Vehicle Glass Distortion Information


This TSB number 00-08-48-005C, dated 02/01/08 has been superceded by TSB number 00-08-48-005D , dated 09/10/10
Technical Service Bulletin # 99-08-64-016B Date: 070622

Body - Use of Silicone for Weatherstrip Maintenance


This TSB number 99-08-64-016B, dated 06/22/07 has been superceded by TSB number 99-08-64-016C , dated 07/29/09
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 157
Chevrolet Venture V6-3.4L VIN E 2482
Technical Service Bulletin # 05-08-46-004A Date: 060222

OnStar(R) - Incorrect Phone Number Assigned to Vehicle


This TSB number 05-08-46-004A, dated 02/22/06 has been superceded by TSB number 05-08-46-004B , dated 01/08/08
Technical Service Bulletin # 02-08-46-006A Date: 050317

OnStar(R) - Incorrect Position Reported


This TSB number 02-08-46-006A, dated 03/17/05 has been superceded by TSB number 02-08-46-006C , dated 01/08/08
Technical Service Bulletin # 00-08-46-004B Date: 050317

OnStar(R) - Re-Establishing Communications


This TSB number 00-08-46-004B, dated 03/17/05 has been superceded by TSB number 00-08-46-004C , dated 01/17/08
Technical Service Bulletin # 01-08-46-008C Date: 050113

OnStar(R) - System Upgrade No Longer Available


This TSB number 01-08-46-008C, dated 01/13/05 has been superceded by TSB number 01-08-46-008D , dated 01/15/08
Technical Service Bulletin # 99-08-46-001 Date: 991101

OnStar(R) - Kit Part Numbers and Compatibility


This TSB number 99-08-46-001, dated 11/01/99 has been superceded by TSB number 99-08-46-001A , dated 03/08/05
Technical Service Bulletin # 05-08-46-004 Date: 050308

OnStar(R) - Phone Number Concerns


This TSB number 05-08-46-004, dated 03/08/05 has been superceded by TSB number 05-08-46-004B , dated 01/08/08
Technical Service Bulletin # 06-08-44-015A Date: 080201

Audio System -Noise When Using Portable Playback Unit


This TSB number 06-08-44-015A, dated 02/01/08 has been superceded by TSB number 06-08-44-015B , dated 05/12/09
Technical Service Bulletin # 00-08-46-003A Date: 050131

Navigation System - Performance Degradation


This TSB number 00-08-46-003A, dated 01/31/05 has been superceded by TSB number 00-08-46-003B , dated 02/09/05
Technical Service Bulletin # 01045A Date: 010801

Campaign - Onstar Global Positioning System Defect


This TSB number 01045A, dated 08/01/01 has been superceded by TSB number 01045B , dated 04/21/06
Technical Service Bulletin # 00-08-46-004A Date: 010301

Instruments - Re-Establishing GPS Communications


This TSB number 00-08-46-004A, dated 03/01/01 has been superceded by TSB number 00-08-46-004C , dated 01/17/08
Technical Service Bulletin # 08089B Date: 080923

Campaign - Deactivating Analog OnStar(R)


This TSB number 08089B, dated 09/23/08 has been superceded by TSB number 08089C , dated 11/18/08
Technical Service Bulletin # 08089A Date: 080714

Campaign - Deactivation of Analog OnStar(R)


This TSB number 08089A, dated 07/14/08 has been superceded by TSB number 08089C , dated 11/18/08
Technical Service Bulletin # 08089 Date: 080613

Campaign - Analog OnStar(R) Deactivation


This TSB number 08089, dated 06/13/08 has been superceded by TSB number 08089C , dated 11/18/08
Technical Service Bulletin # 02-08-46-006B Date: 070523

OnStar(R) - Incorrect GPS Location Reported During Call


This TSB number 02-08-46-006B, dated 05/23/07 has been superceded by TSB number 02-08-46-006C , dated 01/08/08
Technical Service Bulletin # 02-08-46-006 Date: 020501

OnStar (R) - Incorrect GPS Location During OnStar Call


This TSB number 02-08-46-006, dated 05/01/02 has been superceded by TSB number 02-08-46-006C , dated 01/08/08
Technical Service Bulletin # 02-08-46-004 Date: 020401
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 158
Chevrolet Venture V6-3.4L VIN E 2483

OnStar System (R) - Cellular Error Messages


This TSB number 02-08-46-004, dated 04/01/02 has been superceded by TSB number 02-08-46-004A , dated 04/11/06
Technical Service Bulletin # 01-08-46-004 Date: 010801

Cellular Phones - Operating Characteristics


This TSB number 01-08-46-004, dated 08/01/01 has been superceded by TSB number 01-08-46-004A , dated 03/08/05
Technical Service Bulletin # 01-08-46-001 Date: 010501

OnStar(R) Module - Required Reconfiguration


This TSB number 01-08-46-001, dated 05/01/01 has been superceded by TSB number 01-08-46-001A , dated 03/07/05
Technical Service Bulletin # 99-08-52-005 Date: 991001

Remote Keyless Entry - Operational Characteristics


This TSB number 99-08-52-005, dated 10/01/99 has been superceded by TSB number 99-08-52-005C , dated 01/30/08
Technical Service Bulletin # 99-08-52-005A Date: 030501

Keyless Entry System - Operational Characteristics


This TSB number 99-08-52-005A, dated 05/01/03 has been superceded by TSB number 99-08-52-005C , dated 01/30/08
Technical Service Bulletin # 99-08-52-005B Date: 060110

Keyless Entry - Operational Characteristics


This TSB number 99-08-52-005B, dated 01/10/06 has been superceded by TSB number 99-08-52-005C , dated 01/30/08
Technical Service Bulletin # 01-08-46-008A Date: 011201

OnStar(R) - Upgrading Factory Installed Units


This TSB number 01-08-46-008A, dated 12/01/01 has been superceded by TSB number 01-08-46-008D , dated 01/15/08
Technical Service Bulletin # 00-08-46-002 Date: 000901

OnStar(R) - Cellular Antenna Replacement Parts Available


This TSB number 00-08-46-002, dated 09/01/00 has been superceded by TSB number 00-08-46-002A , dated 04/12/05
Technical Service Bulletin # 99-09-40-005D Date: 061220

Restraints - Availability of Seat Belt Extenders


This TSB number 99-09-40-005D, dated 12/20/06 has been superceded by TSB number 99-09-40-005F , dated 06/23/10
Technical Service Bulletin # 99-09-40-005C Date: 051123

Restraints - Seat Belt Extender Availability


This TSB number 99-09-40-005C, dated 11/23/05 has been superceded by TSB number 99-09-40-005F , dated 06/23/10
Technical Service Bulletin # 99-09-40-005B Date: 040901

Restraint System - Seat Belt Extender Availability


This TSB number 99-09-40-005B, dated 09/01/04 has been superceded by TSB number 99-09-40-005F , dated 06/23/10
Technical Service Bulletin # 99-09-40-005A Date: 031022

Interior - Seat Belt Extenders


This TSB number 99-09-40-005A, dated 10/22/03 has been superceded by TSB number 99-09-40-005F , dated 06/23/10
Technical Service Bulletin # 99-09-40-005 Date: 000101

Seat Belt - Extender Availability


This TSB number 99-09-40-005, dated 01/01/00 has been superceded by TSB number 99-09-40-005F , dated 06/23/10
Technical Service Bulletin # 00-09-40-001B Date: 031008

Interior - Excessive Child Seat Lateral Movement


This TSB number 00-09-40-001B, dated 10/08/03 has been superceded by TSB number 00-09-40-001C , dated 01/31/05
Technical Service Bulletin # 00-09-40-001 Date: 000301

Aftermarket Child Seats - Excessive Lateral Movement


This TSB number 00-09-40-001, dated 03/01/00 has been superceded by TSB number 00-09-40-001C , dated 01/31/05
Technical Service Bulletin # 00-09-40-001A Date: 010701
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 159
Chevrolet Venture V6-3.4L VIN E 2484
Child Seat - Excess Lateral Movement
This TSB number 00-09-40-001A, dated 07/01/01 has been superceded by TSB number 00-09-40-001C , dated 01/31/05
Technical Service Bulletin # 05-09-40-002C Date: 090323

Restraints - Seat Belt Operating Characteristic


INFORMATION

Bulletin No.: 05-09-40-002C

Date: March 23, 2009

Subject:
Safety Belt Locking Conditions (Normal Operating Characteristic)

Models:
2005-2010 Passenger Cars and Light Duty Trucks (Including Saturn)
2005-2010 HUMMER H2, H3
2005-2009 Saab 9-7X

Supercede:
This bulletin is being revised to add the 2009 and 2010 model years. Please discard Corporate Bulletin Number 05-09-40-002B (Section 09 -
Restraints).

The purpose of this bulletin is to explain when the front safety belts are supposed to lock. There are several different locking situations.

Vehicle Sensing

This type of locking occurs in response to the vehicle under the following conditions:

- The vehicle changes speed or direction abruptly (the vehicle goes into high acceleration OR high deceleration or there is aggressive
cornering).

- It can also occur in a static condition when a vehicle is parked on a large slant (fore-aft or side-to-side), such as streets in San Francisco,
California.

- It may also occur over rough road conditions where the retractor mechanism is bounced into a locked condition.

In all of these conditions, as long as tension is maintained on the webbing, the belt will stay locked. When the tension is released, the belt retracts
slightly, the lock bar disengages and the safety belt should return to normal function. Please inform customers that may comment that "the belt
locks intermittently" that this is the design intent and the belt is functioning properly.

Web Sensing

This type of locking occurs in response to the extraction of webbing. When the webbing reels out at an accelerated rate, it goes into lock mode and
stays there until tension is again released. To observe this condition, extract the webbing quickly. Customers may refer to this condition as
"intermittent lock-up" and encounter it when trying to put the belt on too quickly.

Automatic Locking (ALR)

This type of locking is provided at the right front passenger position of most vehicles. When the webbing is pulled all the way out, it automatically
converts the retractor into a cinch-down mode (i.e. ALR). This is typically used to tightly secure a child seat to the vehicle. Some customers may
experience inadvertent activation of ALR mode if they happen to pull the belt all the way out to the end of travel while they are putting the belt on.
The ALR mode of operation is automatically cancelled when the belt is unfastened and stowed (the belt returns to normal sensitive function).

Corvette only - This locking mechanism is also provided at the driver's position of the Corvette only, as a unique feature. Corvette customers may
find this feature appealing when they plan to operate the vehicle in a "spirited" manner (such as driving in mountainous terrain). With the ALR
active, the operator is snugly cinched into the seat and kept firmly in place during high G-force driving maneuvers.

Overspool Lock

There is an unintentional locking condition that ALL safety belts from ALL manufacturers may experience called "overspool lock". If the webbing
snaps back to the stowed position rapidly enough, the retractor will lock with the belt fully stowed. This is more likely to occur when customers
"help" the belt to retract. Without the weight of the latch plate and friction to slow the retractive speed of the webbing, the higher than normal
webbing retraction speed that occurs engages the locking mechanism when a sudden stop occurs at the end of web travel. Since the webbing is now
fully loaded on the spool, the retractor cannot rewind itself further to release the locking mechanism. When this happens, the belt cannot be pulled
out to wear. When customers bring their vehicle to the dealership with this condition, they believe replacement is necessary. Replacement is not
necessary for this condition. All the Service Advisor needs to do is pull hard on the locked webbing and then release. The hard pull extracts a small
amount of webbing from the retractor which, in turn, permits a small amount of retraction to occur when released. This is all that is needed to
disengage the locking mechanism. The safety belt will now function properly.
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 160
Chevrolet Venture V6-3.4L VIN E 2485

Disclaimer

Technical Service Bulletin # 99-09-40-005E Date: 080109

Seat Belts - Seat Belt Extender Availability


This TSB number 99-09-40-005E, dated 01/09/08 has been superceded by TSB number 99-09-40-005F , dated 06/23/10
Technical Service Bulletin # 06-08-50-009C Date: 081212

Restraints - Passenger Presence Sensing System Info.


This TSB number 06-08-50-009C, dated 12/12/08 has been superceded by TSB number 06-08-50-009E , dated 02/25/10
Technical Service Bulletin # 06-08-50-009B Date: 070719

Restraints - Front Passenger Seat Accessory Precautions


This TSB number 06-08-50-009B, dated 07/19/07 has been superceded by TSB number 06-08-50-009E , dated 02/25/10
Technical Service Bulletin # 06-08-50-009A Date: 070313

SRS - Front Passenger Seat Alteration Precautions


This TSB number 06-08-50-009A, dated 03/13/07 has been superceded by TSB number 06-08-50-009E , dated 02/25/10
Technical Service Bulletin # 06-08-50-009D Date: 091006

Restraints - Passenger Presence System Information


This TSB number 06-08-50-009D, dated 10/06/09 has been superceded by TSB number 06-08-50-009E , dated 02/25/10
Technical Service Bulletin # 06-08-50-009 Date: 060817

SRS - Occupant Sensing System Precautions


This TSB number 06-08-50-009, dated 08/17/06 has been superceded by TSB number 06-08-50-009E , dated 02/25/10
Technical Service Bulletin # 03-09-41-003 Date: 030729

Restraint System - Proper Air Bag System Diagnosis


This TSB number 03-09-41-003, dated 07/29/03 has been superceded by TSB number 03-09-41-003A , dated 02/09/05
Technical Service Bulletin # 00-00-89-027C Date: 051025

Interior, A/C - Vehicle Odor Elimination


This TSB number 00-00-89-027C, dated 10/25/05 has been superceded by TSB number 00-00-89-027E , dated 09/29/08
Technical Service Bulletin # 01-01-38-006B Date: 030714

A/C - R-134A System Flushing Procedure


This TSB number 01-01-38-006B, dated 07/14/03 has been superceded by TSB number 01-01-38-006D , dated 09/01/04
Technical Service Bulletin # 01-01-38-006A Date: 010701

A/C - Proper Flushing Procedures


This TSB number 01-01-38-006A, dated 07/01/01 has been superceded by TSB number 01-01-38-006D , dated 09/01/04
Technical Service Bulletin # 99-01-39-007A Date: 000301

A/C (Automatic) - Operation Explained


This TSB number 99-01-39-007A, dated 03/01/00 has been superceded by TSB number 99-01-39-007B , dated 03/01/03
Technical Service Bulletin # 99-01-39-004B Date: 070529

A/C - Odors In Hot/Humid Conditions


This TSB number 99-01-39-004B, dated 05/29/07 has been superceded by TSB number 99-01-39-004C , dated 06/12/09
Technical Service Bulletin # 99-01-39-004A Date: 010501

A/C - Odor Emission in Hot Weather


This TSB number 99-01-39-004A, dated 05/01/01 has been superceded by TSB number 99-01-39-004C , dated 06/12/09
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 161
Chevrolet Venture V6-3.4L VIN E 2486
Technical Service Bulletin # 99-01-39-007 Date: 991001

A/C - Automatic Control Operation


This TSB number 99-01-39-007, dated 10/01/99 has been superceded by TSB number 99-01-39-007B , dated 03/01/03
Technical Service Bulletin # 01-01-38-013 Date: 011201

A/C Compressor - Diagnostic Considerations


This TSB number 01-01-38-013, dated 12/01/01 has been superceded by TSB number 01-01-38-013A , dated 10/29/03
Technical Service Bulletin # 00-00-89-027D Date: 061003

Interior - Eliminating Unwanted Odors


This TSB number 00-00-89-027D, dated 10/03/06 has been superceded by TSB number 00-00-89-027E , dated 09/29/08
Technical Service Bulletin # 00-00-89-027A Date: 020101

Interior - New Odor Elimination Product


This TSB number 00-00-89-027A, dated 01/01/02 has been superceded by TSB number 00-00-89-027E , dated 09/29/08
Technical Service Bulletin # 06-02-32-013A Date: 080205

Steering Power Steering Pump Replacement Tips


This TSB number 06-02-32-013A, dated 02/05/08 has been superceded by TSB number 06-02-32-013B , dated 08/07/09
Technical Service Bulletin # 06-02-32-013 Date: 061025

Power Steering - Diagnostic Tips


This TSB number 06-02-32-013, dated 10/25/06 has been superceded by TSB number 06-02-32-013B , dated 08/07/09
Technical Service Bulletin # 02-06-03-008B Date: 070417

Charging System - Low Voltage Display/Low/Dead Battery


This TSB number 02-06-03-008B, dated 04/17/07 has been superceded by TSB number 02-06-03-008D , dated 07/21/08
Technical Service Bulletin # 10-08-45-001A Date: 100604

Electrical - Information For Electrical Ground Repair


This TSB number 10-08-45-001A, dated 06/04/10 has been superceded by TSB number 10-08-45-001B , dated 10/25/10
Technical Service Bulletin # 10-08-45-001 Date: 100305

Electrical - Information For Electrical Ground Repair


This TSB number 10-08-45-001, dated 03/05/10 has been superceded by TSB number 10-08-45-001B , dated 10/25/10
Technical Service Bulletin # 06-08-44-015 Date: 060419

Audio System - Portable Audio Equipment Noise


This TSB number 06-08-44-015, dated 04/19/06 has been superceded by TSB number 06-08-44-015B , dated 05/12/09
Technical Service Bulletin # 06-00-89-051 Date: 061122

Locks - KeyCode Security Rules and Information


This TSB number 06-00-89-051, dated 11/22/06 has been superceded by TSB number 10-00-89-010 , dated 05/27/10
Technical Service Bulletin # 06-00-89-051D Date: 100311

Locks - Key Code Security Rules and Information


This TSB number 06-00-89-051D, dated 03/11/10 has been superceded by TSB number 10-00-89-010 , dated 05/27/10
Technical Service Bulletin # 02-06-03-008C Date: 070530

Charging System - Lights Dim/Low Voltage Display


This TSB number 02-06-03-008C, dated 05/30/07 has been superceded by TSB number 02-06-03-008D , dated 07/21/08
Technical Service Bulletin # 02-06-03-008A Date: 040728

Charging System - Operational Characteristics


This TSB number 02-06-03-008A, dated 07/28/04 has been superceded by TSB number 02-06-03-008D , dated 07/21/08
Technical Service Bulletin # 02-06-03-008 Date: 020801

Charging System - Low Voltage Display ON/Dim Lights


This TSB number 02-06-03-008, dated 08/01/02 has been superceded by TSB number 02-06-03-008D , dated 07/21/08
Technical Service Bulletin # 05-06-03-002B Date: 060314
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 162
Chevrolet Venture V6-3.4L VIN E 2487

Battery, Charging System - Electrical Diagnostics


This TSB number 05-06-03-002B, dated 03/14/06 has been superceded by TSB number 05-06-03-002C , dated 04/17/08
Technical Service Bulletin # 02-06-03-009B Date: 060314

Electrical - Battery Charging Tips


This TSB number 02-06-03-009B, dated 03/14/06 has been superceded by TSB number 02-06-03-009C , dated 04/17/08
Technical Service Bulletin # 05-06-03-002A Date: 050701

Battery/Charging System - Electrical Diagnosis


This TSB number 05-06-03-002A, dated 07/01/05 has been superceded by TSB number 05-06-03-002C , dated 04/17/08
Technical Service Bulletin # 05-06-03-002 Date: 050322

Battery/Charging System - Electrical Diagnostics


This TSB number 05-06-03-002, dated 03/22/05 has been superceded by TSB number 05-06-03-002C , dated 04/17/08
Technical Service Bulletin # 02-06-03-006B Date: 041110

Electrical - Testing Prior to Alternator/Battery R&R


This TSB number 02-06-03-006B, dated 11/10/04 has been superceded by TSB number 05-06-03-002C , dated 04/17/08
Technical Service Bulletin # 02-06-03-006A Date: 021201

Electrical - Testing Before Replacing Battery or Alt


This TSB number 02-06-03-006A, dated 12/01/02 has been superceded by TSB number 05-06-03-002C , dated 04/17/08
Technical Service Bulletin # 02-06-03-010 Date: 021001

Battery - Parasitic Drain Information


This TSB number 02-06-03-010, dated 10/01/02 has been superceded by TSB number 02-06-03-010A , dated 07/02/04
Technical Service Bulletin # 02-06-03-009A Date: 021001

Battery - Charging/Information Tips


This TSB number 02-06-03-009A, dated 10/01/02 has been superceded by TSB number 02-06-03-009C , dated 04/17/08
Technical Service Bulletin # 02-06-03-009 Date: 020801

Battery - Charging Tips


This TSB number 02-06-03-009, dated 08/01/02 has been superceded by TSB number 02-06-03-009C , dated 04/17/08
Technical Service Bulletin # 02-06-03-006 Date: 020701

Battery/Charging System - Diagnosis/Testing


This TSB number 02-06-03-006, dated 07/01/02 has been superceded by TSB number 05-06-03-002C , dated 04/17/08
Technical Service Bulletin # 00-08-46-004 Date: 001101

OnStar(TM) GPS - Battery Service Procedure


This TSB number 00-08-46-004, dated 11/01/00 has been superceded by TSB number 00-08-46-004C , dated 01/17/08
Technical Service Bulletin # 00-05-22-002J Date: 070515

Disc Brake System - Warranty Service and Procedures


This TSB number 00-05-22-002J, dated 05/15/07 has been superceded by TSB number 00-05-22-002L , dated 03/26/09
Technical Service Bulletin # 00-05-22-002I Date: 061130

Brakes - Brake Warranty Service and Procedures


This TSB number 00-05-22-002I, dated 11/30/06 has been superceded by TSB number 00-05-22-002L , dated 03/26/09
Technical Service Bulletin # 00-05-22-002H Date: 060620

Brakes - Warranty Guidelines and Service Procedures


This TSB number 00-05-22-002H, dated 06/20/06 has been superceded by TSB number 00-05-22-002L , dated 03/26/09
Technical Service Bulletin # 00-05-22-002G Date: 060301

Brake System - Service Procedures and Guidelines


This TSB number 00-05-22-002G, dated 03/01/06 has been superceded by TSB number 00-05-22-002L , dated 03/26/09
Technical Service Bulletin # 00-05-22-002F Date: 050609
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 163
Chevrolet Venture V6-3.4L VIN E 2488
Brakes - Service Guidelines and Procedures
This TSB number 00-05-22-002F, dated 06/09/05 has been superceded by TSB number 00-05-22-002L , dated 03/26/09
Technical Service Bulletin # 00-05-22-002E Date: 050310

Brakes - Service Guidelines/Procedures


This TSB number 00-05-22-002E, dated 03/10/05 has been superceded by TSB number 00-05-22-002L , dated 03/26/09
Technical Service Bulletin # 00-05-22-002D Date: 040517

Brakes - Service Procedures/Warranty Guidelines


This TSB number 00-05-22-002D, dated 05/17/04 has been superceded by TSB number 00-05-22-002L , dated 03/26/09
Technical Service Bulletin # 00-05-22-002C Date: 040128

Brakes - Service Procedures/Warranty Requirements


This TSB number 00-05-22-002C, dated 01/28/04 has been superceded by TSB number 00-05-22-002L , dated 03/26/09
Technical Service Bulletin # 00-05-22-002K Date: 080506

Disc Brakes - Warranty Service and Procedures


This TSB number 00-05-22-002K, dated 05/06/08 has been superceded by TSB number 00-05-22-002L , dated 03/26/09
Technical Service Bulletin # 00-05-22-002B Date: 030301

Brakes - Rotor Service Guidelines


This TSB number 00-05-22-002B, dated 03/01/03 has been superceded by TSB number 00-05-22-002L , dated 03/26/09
Technical Service Bulletin # 00-05-22-002A Date: 011201

Brake Rotor - Warranty Service Procedure


This TSB number 00-05-22-002A, dated 12/01/01 has been superceded by TSB number 00-05-22-002L , dated 03/26/09
Technical Service Bulletin # 00-05-22-002 Date: 000201

Brake Rotor - Warranty Service Procedures


This TSB number 00-05-22-002, dated 02/01/00 has been superceded by TSB number 00-05-22-002L , dated 03/26/09
Technical Service Bulletin # 01-05-23-011 Date: 011201

Front Brakes - Rattle Noise On Bumps


This TSB number 01-05-23-011, dated 12/01/01 has been superceded by TSB number 01-05-23-011A , dated 02/01/02
Technical Service Bulletin # 01-05-23-006 Date: 010401

Front/Rear Caliper - Fastener Requirement Revision


This TSB number 01-05-23-006, dated 04/01/01 has been superceded by TSB number 01-05-23-006A , dated 06/01/01
Technical Service Bulletin # 99-04-20-002E Date: 080606

Drivetrain - Driveline Clunk Information


This TSB number 99-04-20-002E, dated 06/06/08 has been superceded by TSB number 99-04-20-002F , dated 11/03/09
Technical Service Bulletin # 99-04-20-002C Date: 050131

Drivetrain - Normal Clunk Shifting Between 'D' & 'R'


This TSB number 99-04-20-002C, dated 01/31/05 has been superceded by TSB number 99-04-20-002F , dated 11/03/09
Technical Service Bulletin # 99-04-20-002B Date: 030821

Drivetrain - Driveline Clunk Explanation


This TSB number 99-04-20-002B, dated 08/21/03 has been superceded by TSB number 99-04-20-002F , dated 11/03/09
Technical Service Bulletin # 03-07-29-004E Date: 080502

M/T - Operating Characteristics of Manual Transmissions


This TSB number 03-07-29-004E, dated 05/02/08 has been superceded by TSB number 03-07-29-004F , dated 07/29/09
Technical Service Bulletin # 03-07-29-004C Date: 060828

M/T - Normal Operating Characteristics


This TSB number 03-07-29-004C, dated 08/28/06 has been superceded by TSB number 03-07-29-004F , dated 07/29/09
Technical Service Bulletin # 03-07-29-004B Date: 050830

M/T - Characteristics of Operation


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 164
Chevrolet Venture V6-3.4L VIN E 2489
This TSB number 03-07-29-004B, dated 08/30/05 has been superceded by TSB number 03-07-29-004F , dated 07/29/09
Technical Service Bulletin # 03-07-29-004A Date: 041112

M/T - Operational Characteristics


This TSB number 03-07-29-004A, dated 11/12/04 has been superceded by TSB number 03-07-29-004F , dated 07/29/09
Technical Service Bulletin # 03-07-29-004 Date: 030401

M/T - Operating Characteristics


This TSB number 03-07-29-004, dated 04/01/03 has been superceded by TSB number 03-07-29-004F , dated 07/29/09
Technical Service Bulletin # 99-04-20-002 Date: 991201

Driveline - Clunk
This TSB number 99-04-20-002, dated 12/01/99 has been superceded by TSB number 99-04-20-002F , dated 11/03/09
Technical Service Bulletin # 01-07-31-002 Date: 011101

M/T - Improved Clutch Bleeding Procedure


This TSB number 01-07-31-002, dated 11/01/01 has been superceded by TSB number 01-07-31-002B , dated 11/01/06
Technical Service Bulletin # 01-07-31-002A Date: 040901

M/T - Improved Hydraulic Clutch Bleeding Procedure


This TSB number 01-07-31-002A, dated 09/01/04 has been superceded by TSB number 01-07-31-002B , dated 11/01/06
Technical Service Bulletin # 00-07-30-009A Date: 050209

A/T - New/Reman A/T Identification


This TSB number 00-07-30-009A, dated 02/09/05 has been superceded by TSB number 00-07-30-009D , dated 02/24/10
Technical Service Bulletin # 00-07-30-009C Date: 091114

A/T - Goodwrench(R) Replacement Transmissions


This TSB number 00-07-30-009C, dated 11/14/09 has been superceded by TSB number 00-07-30-009D , dated 02/24/10
Technical Service Bulletin # 99-04-20-002D Date: 060608

A/T - Clunk When Shifting From PARK/DRIVE/REVERSE


This TSB number 99-04-20-002D, dated 06/08/06 has been superceded by TSB number 99-04-20-002F , dated 11/03/09
Technical Service Bulletin # 03-07-30-007B Date: 050802

A/T - Gear Engagement Time


This TSB number 03-07-30-007B, dated 08/02/05 has been superceded by TSB number 03-07-30-007E , dated 05/05/08
Technical Service Bulletin # 01-07-30-041A Date: 041203

A/T - Fluid Leak Diagnostics


This TSB number 01-07-30-041A, dated 12/03/04 has been superceded by TSB number 01-07-30-041B , dated 10/06/05
Technical Service Bulletin # 03-07-30-007 Date: 030401

A/T - Apparent Delayed Gear Engagement


This TSB number 03-07-30-007, dated 04/01/03 has been superceded by TSB number 03-07-30-007E , dated 05/05/08
Technical Service Bulletin # 01-07-30-041 Date: 011201

A/T - Fluid Leak Diagnosis


This TSB number 01-07-30-041, dated 12/01/01 has been superceded by TSB number 01-07-30-041B , dated 10/06/05
Technical Service Bulletin # 99-04-20-002A Date: 010901

Driveline - Clunk Explanation


This TSB number 99-04-20-002A, dated 09/01/01 has been superceded by TSB number 99-04-20-002F , dated 11/03/09
Technical Service Bulletin # 99-07-30-030A Date: 010401

A/T - Grinding/Growling in Park on an Incline


This TSB number 99-07-30-030A, dated 04/01/01 has been superceded by TSB number 99-07-30-030F , dated 05/01/08
Technical Service Bulletin # 00-07-30-009 Date: 000501

Transmission - Identifying Remanufactured Assemblies


This TSB number 00-07-30-009, dated 05/01/00 has been superceded by TSB number 00-07-30-009D , dated 02/24/10
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 165
Chevrolet Venture V6-3.4L VIN E 2490
Technical Service Bulletin # 01-07-30-032A Date: 020101

A/T - Oil Leak From Vent


This TSB number 01-07-30-032A, dated 01/01/02 has been superceded by TSB number 01-07-30-032E , dated 09/29/08
Technical Service Bulletin # 08-07-30-035 Date: 080808

A/T - Water Or Coolant Contamination Information


This TSB number 08-07-30-035, dated 08/08/08 has been superceded by TSB number 08-07-30-035B , dated 11/01/10
Technical Service Bulletin # 02-07-30-052E Date: 080222

Automatic Transmission - Fluid Cooler Flushing


This TSB number 02-07-30-052E, dated 02/22/08 has been superceded by TSB number 02-07-30-052F , dated 09/09/09
Technical Service Bulletin # 02-07-30-052B Date: 030207

A/T - Oil Cooler Flushing Tool/Procedure


This TSB number 02-07-30-052B, dated 02/07/03 has been superceded by TSB number 02-07-30-052F , dated 09/09/09
Technical Service Bulletin # 04-07-30-017A Date: 080916

A/T - Revised Cooler Line Fitting/Converter Check Valve


This TSB number 04-07-30-017A, dated 09/16/08 has been superceded by TSB number 04-07-30-017B , dated 11/25/08
Technical Service Bulletin # 01-07-30-010B Date: 051001

A/T - Torque Converter Replacement


This TSB number 01-07-30-010B, dated 10/01/05 has been superceded by TSB number 01-07-30-010C , dated 05/12/08
Technical Service Bulletin # 01-07-30-010A Date: 040806

A/T - Torque Converter Replacement Guideline


This TSB number 01-07-30-010A, dated 08/06/04 has been superceded by TSB number 01-07-30-010C , dated 05/12/08
Technical Service Bulletin # 01-07-30-010 Date: 010301

A/T - Torque Converter Replacement Guidelines


This TSB number 01-07-30-010, dated 03/01/01 has been superceded by TSB number 01-07-30-010C , dated 05/12/08
Technical Service Bulletin # 00-07-30-022C Date: 041210

A/T - 4L60/65E No Reverse/2nd or 4th Gear


This TSB number 00-07-30-022C, dated 12/10/04 has been superceded by TSB number 00-07-30-022D , dated 06/10/08
Technical Service Bulletin # 00-07-30-022B Date: 041118

A/T - 4L60E/4L65E No Reverse/2nd or 4th Gears


This TSB number 00-07-30-022B, dated 11/18/04 has been superceded by TSB number 00-07-30-022D , dated 06/10/08
Technical Service Bulletin # 99-07-30-030E Date: 070103

A/T - Grinding/Growling In PARK On An Incline


This TSB number 99-07-30-030E, dated 01/03/07 has been superceded by TSB number 99-07-30-030F , dated 05/01/08
Technical Service Bulletin # 99-07-30-030B Date: 021201

A/T - Grinding/Growling While in PARK on an Incline


This TSB number 99-07-30-030B, dated 12/01/02 has been superceded by TSB number 99-07-30-030F , dated 05/01/08
Technical Service Bulletin # 01-07-30-032D Date: 061030

A/T - Fluid Leaking From Vent


This TSB number 01-07-30-032D, dated 10/30/06 has been superceded by TSB number 01-07-30-032E , dated 09/29/08
Technical Service Bulletin # 01-07-30-032C Date: 060726

A/T - 4T65-E Oil Leak From Transmission Vent


This TSB number 01-07-30-032C, dated 07/26/06 has been superceded by TSB number 01-07-30-032E , dated 09/29/08
Technical Service Bulletin # 01-07-30-032 Date: 011001

A/T - Oil Leak


This TSB number 01-07-30-032, dated 10/01/01 has been superceded by TSB number 01-07-30-032E , dated 09/29/08
Technical Service Bulletin # 04-07-30-028 Date: 040615
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 166
Chevrolet Venture V6-3.4L VIN E 2491

A/T - Reverse Servo Cover Seal Leak


This TSB number 04-07-30-028, dated 06/15/04 has been superceded by TSB number 04-07-30-028A , dated 01/12/06
Technical Service Bulletin # 02-07-30-022A Date: 020901

Transmission Controls - SES Lamp ON/ DTC's Set


This TSB number 02-07-30-022A, dated 09/01/02 has been superceded by TSB number 02-07-30-022B , dated 10/20/03
Technical Service Bulletin # 02-07-30-001E Date: 061207

A/T - Diagnostic Info on DTCs P0894/P1870


This TSB number 02-07-30-001E, dated 12/07/06 has been superceded by TSB number 02-07-30-001G , dated 03/19/08
Technical Service Bulletin # 04-06-04-047H Date: 080624

Fuel System 'TOP TIER' Detergent Gasoline Information


This TSB number 04-06-04-047H, dated 06/24/08 has been superceded by TSB number 04-06-04-047I , dated 08/17/09
Technical Service Bulletin # 03-06-04-030B Date: 070215

Fuel System - Poor Performance Due To Injector Clogging


Bulletin No.: 03-06-04-030B

Date: February 15, 2007

TECHNICAL

Subject:
Various Driveability Symptoms Due to Clogged Fuel Injectors, MIL/SES DTCs P0171, P0172, P0174, P0300, P1174, P1175 (Clean Fuel Injectors
and/or Perform Injector Test With AFIT - CH47976)

Models:
2000-2007 GM Passenger Cars and Light Duty Trucks (Including Saturn)
2003-2007 HUMMER H2
2006-2007 HUMMER H3
2005-2007 Saab 9-7X

with 2.2L, 2.4L, 2.8L, 3.1L, 3.4L, 3.5L, 3.8L, 4.2L, 4.3L, 4.8L, 5.3L, 6.0L, 6.2L or 8.1L Engine (VINs F, D, 4, 5, T, 8, J, E, H, L, 6, K, S, X, V, T,
M, N, U, H, Y, 8, G - RPOs L61, LN2, L43, LD9, LK5, LG8, LA1, LX5, LX9, L52, L36, LL8, LU3, LR4, LM7, LH6, LQ9, LQ4, LS2, L76, L92,
L18)

and MULTEC(R) 2 Fuel Injectors

Supercede:

This bulletin is being revised to update the model years and models, the procedure (recommended specifically for MULTEC(R) 2 injectors) and
recommend cleaning solutions and/or testing with AFIT - CH47976. Please discard Corporate Bulletin Number 03-06-04-030A (Section 06 -
Engine/Propulsion System).

Condition

Some customers may comment on any of the following various driveability symptoms:

Extended Crank Time

Hard to Start

MIL/SES Illuminated with DTCs:

Hesitation

Lack of Power

Surge or Chuggle

Rough Idle

Light or Intermittent Misfire

Cause
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 167
Chevrolet Venture V6-3.4L VIN E 2492

Due to various factors, the fuel injectors may become restricted. Extensive testing has demonstrated that fuel related issues are the cause of clogged
injectors. At this point, no specific fuel, fuel constituent, or engine condition has been identified as causing the restriction. The restriction causes the
engine to operate at a lean air fuel ratio. This may either trigger the MIL to illuminate or the engine to develop various driveability symptoms.

Parts Information

Warranty Information (excluding Saab U.S. Models)

For vehicles repaired under warranty, use the table.

Warranty Information (Saab U.S. Models)


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 168
Chevrolet Venture V6-3.4L VIN E 2493

For vehicles repaired under warranty, use the table.


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 169
Chevrolet Venture V6-3.4L VIN E 2494
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 170
Chevrolet Venture V6-3.4L VIN E 2495

Injector Worksheet

Disclaimer

Correction
Correction

Fuel injector restrictions, deposits can be cleaned on the vehicle using the following procedure. Under NO circumstances should this procedure be
modified, changed or shortened. As a long term solution, and to prevent reoccurrence, customers should be encouraged to use Top Tier Detergent
Gasoline. For further information on Top Tier detergent gasoline and fuel retailers, please refer to the following Corporate Bulletin Numbers:

04-06-04-047G (U.S. Only)


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 171
Chevrolet Venture V6-3.4L VIN E 2496

05-06-04-022C (Canada ONLY)

GM UPPER ENGINE AND FUEL INJECTOR CLEANER is the only injector cleaning agent approved for use with General Motors fuel system
components.

Other injector cleaners may cause damage to plastics, plated metals or bearings. General Motors has completed extensive laboratory testing of GM
Upper Engine and Fuel Injector Cleaner, and can assure its compatibility with General Motors fuel system components, as long as the cleaning
procedure is followed correctly.

Injector Cleaning Procedure

The following tools, or their equivalent, are required:

CH47976 Active Fuel Injector Tester (AFIT)

J 35800-A Fuel Injector Cleaner

J 37287 Fuel Line Shut-off Adapter

J 42964 Fuel Line Shut-off Adapter

J 42873 Fuel Line Shut-off Adapter

* One bottle of GM Upper Engine and Fuel Injector Cleaner, P/N 88861802 (in Canada, P/N 88861804)

* One bottle of GM Fuel System Treatment Plus, P/N 88861011 (in Canada, P/N 88861012)

Active Fuel Injector Tester (AFIT- CH47976)

Some dealers may not have an Active Fuel Injector Tester (AFIT - CH47976). Dealers can contact 1-800-GM-TOOLS (1-800-468-6657) to order
an AFIT - CH47976. Dealers still can test the fuel injectors without an AFIT. Refer to Fuel Injector Diagnosis (w/J 39021 or Tech 2(R)) in SI.

As mentioned in the AFIT User Guide, vehicles that are not listed in the AFIT menu can still be tested with the AFIT. Depending on the model, it
may be possible to enter the previous model year and proceed with testing using the DLC connection. If this is not possible on the model that you
are working on, it will be necessary to use the direct connection method outlined in the AFIT User Guide (See Pages 17-31).

General Motors recommends that the Active Fuel Injector Tester (AFIT) be used in testing fuel injectors. If the SI diagnostics do not isolate a cause
for this concern, use the Active Fuel Injector Tester (AFIT - CH47976) to perform an "Injector Test" as outlined in the AFIT User Guide.

The AFIT "Injector Test" measures the flow characteristics of all fuel injectors, which is more precise when compared with the standard Tech 2(R)
fuel injector balance test. As a result, the AFIT is more likely to isolate the cause of a P1174 DTC (for example: if it is being caused by a fuel
injector concern).

The CH-47976 (Active Fuel Injector Tester - AFT) can also be used to measure fuel pressure and fuel system leak down. Also, as mentioned in the
P1174 SI diagnosis, if the misfire current counters or misfire graph indicate any misfires, it may be an indicator of the cylinder that is causing the
concern. Refer to Fuel Injector Diagnosis (W/CH 47976) in SI for additional instructions.

Training (U.S.)

To access the training video on AFIT, take the following path at the GM Training Website:

After logging into the gmtraining.com website, choose the link on the left side of the page titled web video library.

Then choose "technical".

Next, within the search box, type in September course number 10206.09D.

This will bring up a link with this course. Scroll through to choose feature topic."

At this point, the seminar can be chosen to view or the video related to the AFIT.

Additional training is available from the gmtraining.comwebsite. Please see TECHassist 16044.18T2 Active Fuel Injector Tester and also see
16043.51D Engine Mechanical Diagnosis & Measurement for more information on GM Upper Engine and Fuel Injector Cleaner.

Training (Canada)

To access the training video on AFIT, take the following path at the GMPro LMS Training Website:

After logging into the <www.gmprocanada.com> website, choose the link on the left side of the page titled "Catalog."
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 172
Chevrolet Venture V6-3.4L VIN E 2497

Then choose "Catalog Search."

Next, within the search box, Select Course Number - Contains - "T" then select search.

This will bring up a list of TECHassist courses. Scroll through to choose "Active Fuel Injector Tester" and select "View."

At this point, a new window will open and the program can be Launched.

Techlink

Additional information can be found on AFIT (June 2006 Edition) and GM Upper Engine and Fuel Injector Cleaner (November 2006 Edition) in
Techlink. To access the articles, take the following path:

Go to GM DealerWorld (U.S.) or the GM infoNET (Canada).

Click on the Service Tab in DealerWorld (GM infoNET for Canada).

Click on the GM Techlink Hyperlink.

Click on the Archives Hyperlink at GM Techlink.

Click on 06-2006 in the Archives Section and Click on the Active Fuel Injector Tester Link in the June 2006 Techlink Article. Click on 11-2006 in
the Archives Section and Click on the GM Top Engine Cleaner Replaced Link in the November 2006 Techlink Article.

Injector Cleaning Procedure

GM UPPER ENGINE AND FUEL INJECTOR CLEANER is the only injector cleaning agent recommended. DO NOT USE OTHER CLEANING
AGENTS AS THEY MAY CONTAIN METHANOL, WHICH CAN DAMAGE FUEL SYSTEM COMPONENTS. Under NO circumstances
should the GM Upper Engine and Fuel Injector Cleaner be added to the vehicle fuel tank.

Do not exceed the recommended cleaning solution concentration. Testing has demonstrated that exceeding the recommended cleaning solution
concentration does not improve the effectiveness of this procedure.

Vehicles with less than 160 km (100 mi) on the odometer should not have the injectors cleaned. These vehicles should have any out of specification
injectors replaced.

For 4, 5 and 6 cylinder engines, empty two of the 30 ml (1 oz) reservoirs of the GM Upper Engine and Fuel Injector Cleaner container into the J
35800-A, injector cleaning tank. If you are using any other brand of cleaning tank, you will need a total of 60 ml (2 oz) mixed with 420 ml (14 oz)
of regular unleaded gasoline.

For 8 cylinder engines, empty two of the 30 ml (1 oz) reservoirs of the GM Upper Engine and Fuel Injector Cleaner container into the J 35800-A,
injector cleaning tank. If you are using any other brand of cleaning tank, you will need a total of 60 ml (2 oz) of Upper Engine and Fuel Injector
Cleaner mixed with 420 ml (14 oz) of regular unleaded gasoline. This procedure will need to be repeated for a second time for an 8 cylinder engine
(8 cylinder engines receive 960 ml total fluid - 120 ml (4 oz) of Upper Engine and Fuel Injector Cleaner and 840 ml (28 oz) of gasoline.

Fill the injector cleaning tank with regular unleaded gasoline. Be sure to follow all additional instructions provided with the tool.

Electrically disable the vehicle fuel pump by removing the fuel pump relay and disconnecting the oil pressure switch connector, if equipped.

Turn the ignition to the OFF position.

Relieve fuel pressure and disconnect the fuel feed and return lines at the fuel rail. Plug the fuel feed and return lines coming off the fuel rail with J
37287, J 42873 or J 42964 as appropriate for the fuel system.

Connect the J 35800-A to the vehicle fuel rail.

Pressurize the J 35800-A to 510 kPa (75 psi).

Start and idle the engine until it stalls, due to lack of fuel. This should take approximately 15-20 minutes.

Turn the ignition to the OFF position.

Disconnect the J 35800-A from the fuel rail.

Reconnect the vehicle fuel pump relay and oil pressure switch connector, if equipped.

Remove the J 37287, J 42873 or J 42964 and reconnect the vehicle fuel feed and return lines.

Start and idle the vehicle for an additional two minutes to ensure residual injector cleaner is flushed from the fuel rail and fuel lines.
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 173
Chevrolet Venture V6-3.4L VIN E 2498

Pour the entire contents of GM Fuel System Treatment Plus (P/N 88861011 [in Canada, P/N 88861012]) into the tank and advise the customer to
fill the tank.

Review the benefits of using Top Tier Detergent gasoline with the customer and recommend that they add a bottle of GM Fuel System Treatment
Plus to the fuel tank at every oil change. Regular use of GM Fuel System Treatment Plus should keep the customer from having to repeat the
injector cleaning procedure.

Road test the vehicle to verify that the customer concern has been corrected.

Technical Service Bulletin # 04-06-04-051A Date: 040901

Fuel System - Maintenance Cleaning of Fuel Injectors


This TSB number 04-06-04-051A, dated 09/01/04 has been superceded by TSB number 04-06-04-051B , dated 01/04/06
Technical Service Bulletin # 05-06-04-022E Date: 080806

Fuel System - TOP TIER Detergent Gasoline (Canada)


This TSB number 05-06-04-022E, dated 08/06/08 has been superceded by TSB number 05-06-04-022G , dated 10/27/10
Technical Service Bulletin # 05-06-04-022D Date: 070726

Fuel System - TOP TIER Gasoline Usage (Canada)


This TSB number 05-06-04-022D, dated 07/26/07 has been superceded by TSB number 05-06-04-022G , dated 10/27/10
Technical Service Bulletin # 05-06-04-022C Date: 061128

Fuel System - TOP TIER Detergent Gasoline Usage


This TSB number 05-06-04-022C, dated 11/28/06 has been superceded by TSB number 05-06-04-022G , dated 10/27/10
Technical Service Bulletin # 04-06-04-047G Date: 061128

Fuel System - TOP TIER Detergent Gasoline


This TSB number 04-06-04-047G, dated 11/28/06 has been superceded by TSB number 04-06-04-047I , dated 08/17/09
Technical Service Bulletin # 05-00-89-078A Date: 060914

Fuel System - GM Fuel System Treatment Plus(R)


This TSB number 05-00-89-078A, dated 09/14/06 has been superceded by TSB number 05-00-89-078B , dated 02/06/08
Technical Service Bulletin # 05-06-04-022B Date: 060727

Fuel System - TOP TIER Gasoline Information (Canada)


This TSB number 05-06-04-022B, dated 07/27/06 has been superceded by TSB number 05-06-04-022G , dated 10/27/10
Technical Service Bulletin # 04-06-04-047F Date: 060721

Fuel System - TOP TIER Gasoline Information


This TSB number 04-06-04-047F, dated 07/21/06 has been superceded by TSB number 04-06-04-047I , dated 08/17/09
Technical Service Bulletin # 06-06-04-035 Date: 060713

Fuel System - E85 Fuel Usage Information


This TSB number 06-06-04-035, dated 07/13/06 has been superceded by TSB number 06-06-04-035A , dated 02/05/08
Technical Service Bulletin # 05-06-04-035B Date: 060531

Fuel System - E85 Fuel Usage Recommendations


This TSB number 05-06-04-035B, dated 05/31/06 has been superceded by TSB number 05-06-04-035C , dated 07/30/07
Technical Service Bulletin # 05-06-04-022A Date: 060516

Fuel System - TOP TIER Gasoline Usage Recommendations


This TSB number 05-06-04-022A, dated 05/16/06 has been superceded by TSB number 05-06-04-022G , dated 10/27/10
Technical Service Bulletin # 05-06-04-035A Date: 060309

Fuel System - E85 Fuel Usage


This TSB number 05-06-04-035A, dated 03/09/06 has been superceded by TSB number 05-06-04-035C , dated 07/30/07
Technical Service Bulletin # 05-00-89-078 Date: 051109

Fuel System - Fuel System Treatment PLUS(R)


This TSB number 05-00-89-078, dated 11/09/05 has been superceded by TSB number 05-00-89-078B , dated 02/06/08
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 174
Chevrolet Venture V6-3.4L VIN E 2499
Technical Service Bulletin # 04-06-04-047E Date: 050817

Fuel System - TOP TIER Gasoline Recommendations


This TSB number 04-06-04-047E, dated 08/17/05 has been superceded by TSB number 04-06-04-047I , dated 08/17/09
Technical Service Bulletin # 05-06-04-035 Date: 050523

Fuel System - E85 Fuel Usage Recommendations/Precautions


This TSB number 05-06-04-035, dated 05/23/05 has been superceded by TSB number 05-06-04-035C , dated 07/30/07
Technical Service Bulletin # 05-06-04-022 Date: 050317

Fuel System - Top Tier Gasolines (Canada)


This TSB number 05-06-04-022, dated 03/17/05 has been superceded by TSB number 05-06-04-022G , dated 10/27/10
Technical Service Bulletin # 04-06-04-047D Date: 050317

Fuel System - Top Tier Gasoline Recommendations


This TSB number 04-06-04-047D, dated 03/17/05 has been superceded by TSB number 04-06-04-047I , dated 08/17/09
Technical Service Bulletin # 04-06-04-047C Date: 041214

Fuel System - 'Top Tier' Gasoline Information


This TSB number 04-06-04-047C, dated 12/14/04 has been superceded by TSB number 04-06-04-047I , dated 08/17/09
Technical Service Bulletin # 04-06-04-047A Date: 040901

Fuel System - Top Tier Gasoline Information


This TSB number 04-06-04-047A, dated 09/01/04 has been superceded by TSB number 04-06-04-047I , dated 08/17/09
Technical Service Bulletin # 04-06-04-047 Date: 040601

Fuel System - New Top Tier Detergent Gasoline


This TSB number 04-06-04-047, dated 06/01/04 has been superceded by TSB number 04-06-04-047I , dated 08/17/09
Technical Service Bulletin # 04-06-04-036 Date: 040520

Engine Controls - Reprogramming Warranty Info.


This TSB number 04-06-04-036, dated 05/20/04 has been superceded by TSB number 04-06-04-036E , dated 05/08/08
Technical Service Bulletin # 01-08-45-005 Date: 011001

Engine - Hard/No Start/Stall/Inoperative Fuel Gauge


This TSB number 01-08-45-005, dated 10/01/01 has been superceded by TSB number 01-08-45-005E , dated 08/29/06
Technical Service Bulletin # 00-06-04-011 Date: 000201

Evaporative Emission - Testing on Vehicles


This TSB number 00-06-04-011, dated 02/01/00 has been superceded by TSB number 00-06-04-011A , dated 10/01/01
Technical Service Bulletin # 01-07-30-036G Date: 080512

A/T - DTC P0756 Diagnostic Hints


This TSB number 01-07-30-036G, dated 05/12/08 has been superceded by TSB number 01-07-30-036H , dated 01/29/09
Technical Service Bulletin # 03-06-04-030F Date: 071210

Fuel System - MIL ON/Driveability Issues


Bulletin No.: 03-06-04-030F

Date: December 10, 2007

TECHNICAL

Subject:
Various Driveability Symptoms Due to Clogged Fuel Injectors, MIL/SES DTCs P0171, P0172, P0174, P0300, P1174, P1175 (Clean Fuel Injectors
and/or Perform Injector Test With AFIT - CH-47976)
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 175
Chevrolet Venture V6-3.4L VIN E 2500

Models

Supercede:

This bulletin is being revised to update the model year to 2008. Please discard Corporate Bulletin Number 03-06-04-030E (Section 06 -
Engine/Propulsion System).

Condition

Some customers may comment on any of the following various driveability symptoms:

Extended Crank Time

Hard to Start

MIL/SES Illuminated with DTCs

Hesitation

Lack of Power

Surge or Chuggle

Rough Idle

Light or Intermittent Misfire

Cause

Due to various factors, the fuel injectors may become restricted. Extensive testing has demonstrated that fuel related issues are the cause of clogged
injectors. At this point, no specific fuel, fuel constituent, or engine condition has been identified as causing the restriction. The restriction causes the
engine to operate at a lean air fuel ratio. This may either trigger the MIL to illuminate or the engine to develop various driveability symptoms.

Correction

Fuel injector restrictions, deposits can be cleaned on the vehicle using the following procedure. Under NO circumstances should this procedure be
modified, changed or shortened. As a long term solution, and to prevent reoccurrence, customers should be encouraged to use Top Tier Detergent
Gasoline. For further information on Top Tier detergent gasoline and fuel retailers, please refer to the following Corporate Bulletin Numbers:

04-06-04-047G (U.S. Only)

05-06-04-022D (Canada ONLY)

GM UPPER ENGINE AND FUEL INJECTOR CLEANER is the only injector cleaning agent approved for use with General Motors fuel system
components. Other injector cleaners may cause damage to plastics, plated metals or bearings. General Motors has completed extensive laboratory
testing of GM Upper Engine and Fuel Injector Cleaner, and can assure its compatibility with General Motors fuel system components, as long as
the cleaning procedure is followed correctly.

Injector Cleaning Procedure

The following tools, or their equivalent, are required:

CH-47976 Active Fuel Injector Tester (AFIT)

J 35800-A Fuel Injector Cleaner

J 37287 Fuel Line Shut-off Adapter


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 176
Chevrolet Venture V6-3.4L VIN E 2501

J 42964 Fuel Line Shut-off Adapter

J 42873 Fuel Line Shut-off Adapter

* One bottle of GM Upper Engine and Fuel Injector Cleaner, P/N 88861802 (in Canada, P/N 88861804)

* One bottle of GM Fuel System Treatment Plus, P/N 88861011 (in Canada, P/N 88861012)

Active Fuel Injector Tester (AFIT - CH-47976)

Some dealers may not have an Active Fuel Injector Tester (AFIT- CH-47976). Dealers can contact 1-800-GM-TOOLS (1-800-468-6657) to order
an AFIT - CH-47976. Dealers still can test the fuel injectors without an AFIT. Refer to Fuel Injector Diagnosis (w/J 39021 or Tech 2(R)) in SI.

As mentioned in the AFIT User Guide, vehicles that are not listed in the AFIT menu can still be tested with the AFIT. Depending on the model, it
may be possible to enter the previous model year and proceed with testing using the DLC connection. If this is not possible on the model that you
are working on, it will be necessary to use the direct connection method outlined in the AFIT User Guide (See Pages 17-31).

General Motors recommends that the Active Fuel Injector Tester (AFIT) be used in testing fuel injectors. If the SI diagnostics do not isolate a cause
for this concern, use the Active Fuel Injector Tester (AFIT - CH-47976) to perform an Injector Test as outlined in the AFIT User Guide.

The AFIT Injector Test measures the flow characteristics of all fuel injectors, which is more precise when compared with the standard Tech 2(R)
fuel injector balance test. As a result, the AFIT is more likely to isolate the cause of a P1174 DTC (for example: if it is being caused by a fuel
injector concern).

The CH-47976 (Active Fuel Injector Tester - AFIT) can also be used to measure fuel pressure and fuel system leak down. Also, as mentioned in the
P1174 SI diagnosis, if the misfire current counters or misfire graph indicate any misfires, it may be an indicator of the cylinder that is causing the
concern. Refer to Fuel Injector Diagnosis (w/CH-47976) in SI for additional instructions.

Training (U.S.)

To access the training video on AFIT, take the following path at the GM Training Website:

After logging into the gmtraining.com website, choose the link on the left side of the page titled web video library.

Then choose "technical".

Next, within the search box, type in September course number "10206.09D".

This will bring up a link with this course. Scroll through to choose "feature topic"."

At this point, the seminar can be chosen to view or the video related to the AFIT.

Additional training is available from the gmtraining.com website. Please see TECHassist 16044.18T2 Active Fuel Injector Tester and also see
16044.14D1 GM Powertrain Performance for more information on GM Upper Engine and Fuel Injector Cleaner.

Also, dealers can now download software updates for the AFIT at GM Dealer Equipment (GMDE) on the web at http://www.gmde.net/AFIT.cfm.

Training (Canada)

To access the training video on AFIT, take the following path at the GMPro LMS Training Website:

After logging into the <www.gmprocanada.com> website, choose the link on the left side of the page titled "Catalog."

Then choose "Catalog Search."

Next, within the search box, Select Course Number - Contains - "T" then select search.

This will bring up a list of TECHassist courses. Scroll through to choose "Active Fuel Injector Tester" and select "View."

At this point, a new window will open and the program can be Launched.

Also, dealers can now download software updates for the AFIT at GM Dealer Equipment (GMDE) on the web at
http://www.gmde.net/softwareupdates/.

Techlink

Additional information can be found on AFIT (June 2006 Edition) and GM Upper Engine and Fuel Injector Cleaner (November 2006 Edition) in
Techlink. To access the articles, take the following path:
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 177
Chevrolet Venture V6-3.4L VIN E 2502

Go to GM DealerWorld (U.S.) or the GM infoNET (Canada).

Click on the Service Tab in DealerWorld (GM infoNET for Canada).

Click on the GM Techlink Hyperlink.

Click on the Archives Hyperlink at GM Techlink.

Click on 06-2006 in the Archives Section and Click on the Active Fuel Injector Tester Link in the June 2006 Techlink Article.

Click on 11-2006 in the Archives Section and Click on the GM Top Engine Cleaner Replaced Link in the November 2006 Techlink Article.

Injector Cleaning Procedure

GM UPPER ENGINE AND FUEL INJECTOR CLEANER is the only injector cleaning agent recommended. DO NOT USE OTHER CLEANING
AGENTS AS THEY MAY CONTAIN METHANOL, WHICH CAN DAMAGE FUEL SYSTEM COMPONENTS. Under NO circumstances
should the GM Upper Engine and Fuel Injector Cleaner be added to the vehicle fuel tank.

Do not exceed the recommended cleaning solution concentration. Testing has demonstrated that exceeding the recommended cleaning solution
concentration does not improve the effectiveness of this procedure.

Vehicles with less than 160 km (100 mi) on the odometer should not have the injectors cleaned. These vehicles should have any out of specification
injectors replaced.

For 4, 5 and 6 cylinder engines, empty two of the 30 ml (1 oz) reservoirs of the GM Upper Engine and Fuel Injector Cleaner container into the J
35800-A - Injector Cleaning Tank then add 420 ml (14 oz) of regular unleaded gasoline. If you are using any other brand of cleaning tank, you will
need a total of 60 ml (2 oz) mixed with 420 ml (14 oz) of regular unleaded gasoline.

For 8 cylinder engines, empty two of the 30 ml (1 oz) reservoirs of the GM Upper Engine and Fuel Injector Cleaner container into the J 35800-A -
Injector Cleaning Tank then add 420 ml (14 oz) of regular unleaded gasoline. If you are using any other brand of cleaning tank, you will need a
total of 60 ml (2 oz) of Upper Engine and Fuel Injector Cleaner mixed with 420 ml (14 oz) of regular unleaded gasoline. This procedure will need
to be repeated for a second time for an 8 cylinder engine (8 cylinder engines receive 960 ml total fluid - 120 ml (4 oz) of Upper Engine and Fuel
Injector Cleaner and 840 ml (28 oz) of gasoline.

Be sure to follow all additional instructions provided with the tool.

Electrically disable the vehicle fuel pump by either removing the fuel pump fuse or the fuel pump relay and disconnecting the oil pressure switch
connector, if equipped.

Turn the ignition to the OFF position.

Relieve fuel pressure and disconnect the fuel feed and return lines at the fuel rail. Plug the fuel feed and return lines coming off the fuel rail with J
37287, J 42873 or J 42964 as appropriate for the fuel system.

Connect the J 35800-A to the vehicle fuel rail.

Pressurize the J 35800-A to 510 kPa (75 psi).

Start and idle the engine until it stalls, due to lack of fuel. This should take approximately 15-20 minutes.

Turn the ignition to the OFF position.

Disconnect the J 35800-A from the fuel rail.

Reconnect the vehicle fuel pump relay and oil pressure switch connector, if equipped.

Remove the J 37287, J 42873 or J 42964 and reconnect the vehicle fuel feed and return lines.

Start and idle the vehicle for an additional two minutes to ensure residual injector cleaner is flushed from the fuel rail and fuel lines.

Pour the entire contents of GM Fuel System Treatment Plus (P/N 88861011 [in Canada, P/N 88861012]) into the tank and advise the customer to
fill the tank.

Review the benefits of using Top Tier Detergent gasoline with the customer and recommend that they add a bottle of GM Fuel System Treatment
Plus to the fuel tank at every oil change. Regular use of GM Fuel System Treatment Plus should keep the customer from having to repeat the
injector cleaning procedure. Road test the vehicle to verify that the customer concern has been corrected.
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 178
Chevrolet Venture V6-3.4L VIN E 2503

Parts Information

Warranty Information (excluding Saab U.S. Models)

For vehicles repaired under warranty, use the table.

Warranty Information (Saab U.S. Models)


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 179
Chevrolet Venture V6-3.4L VIN E 2504

For vehicles repaired under warranty, use the table.

Disclaimer

Technical Service Bulletin # 04-06-04-036C Date: 070830

Engine Controls - Warranty Info., Emissions Programming


This TSB number 04-06-04-036C, dated 08/30/07 has been superceded by TSB number 04-06-04-036E , dated 05/08/08
Technical Service Bulletin # 03-06-04-030E Date: 070612

Fuel System - Driveability Issues/MIL ON/DTC's Set


Bulletin No.: 03-06-04-030E

Date: June 12, 2007

TECHNICAL

Subject:
Various Driveability Symptoms Due to Clogged Fuel Injectors, MIL/SES DTCs P0171, P0172, P0174, P0300, P1174, P1175 (Clean Fuel Injectors
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 180
Chevrolet Venture V6-3.4L VIN E 2505
and/or Perform Injector Test With AFIT - CH-47976)

Models

Supercede:

This bulletin is being revised to update the service information in step number 3 under Injector Cleaning Procedure and update the Warranty
Information (excluding Saab U.S. Models). Please discard Corporate Bulletin Number 03-06-04-030D (Section 06 - Engine/Propulsion System).

Condition

Some customers may comment on any of the following various driveability symptoms:

Extended Crank Time

Hard to Start

MIL/SES Illuminated with DTCs

Hesitation

Lack of Power

Surge or Chuggle

Rough Idle

Light or Intermittent Misfire

Cause

Due to various factors, the fuel injectors may become restricted. Extensive testing has demonstrated that fuel related issues are the cause of clogged
injectors. At this point, no specific fuel, fuel constituent, or engine condition has been identified as causing the restriction. The restriction causes the
engine to operate at a lean air fuel ratio. This may either trigger the MIL to illuminate or the engine to develop various driveability symptoms.

Correction

Fuel injector restrictions, deposits can be cleaned on the vehicle using the following procedure. Under NO circumstances should this procedure be
modified, changed or shortened. As a long term solution, and to prevent reoccurrence, customers should be encouraged to use Top Tier Detergent
Gasoline. For further information on Top Tier detergent gasoline and fuel retailers, please refer to the following Corporate Bulletin Numbers:

04-06-04-047G (U.S. Only)

05-06-04-022C (Canada ONLY)

GM UPPER ENGINE AND FUEL INJECTOR CLEANER is the only injector cleaning agent approved for use with General Motors fuel system
components. Other injector cleaners may cause damage to plastics, plated metals or bearings. General Motors has completed extensive laboratory
testing of GM Upper Engine and Fuel Injector Cleaner, and can assure its compatibility with General Motors fuel system components, as long as
the cleaning procedure is followed correctly.

The following tools, or their equivalent, are required:

CH-47976 Active Fuel Injector Tester (AFIT)

J 35800-A Fuel Injector Cleaner

J 37287 Fuel Line Shut-off Adapter


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 181
Chevrolet Venture V6-3.4L VIN E 2506

J 42964 Fuel Line Shut-off Adapter

J 42873 Fuel Line Shut-off Adapter

* One bottle of GM Upper Engine and Fuel Injector Cleaner, P/N 88861802 (in Canada, P/N 88861804)

* One bottle of GM Fuel System Treatment Plus, P/N 88861011 (in Canada, P/N 88861012)

Some dealers may not have an Active Fuel Injector Tester (AFIT - CH-47976). Dealers can contact 1-800-GM-TOOLS (1-800-468-6657) to order
an AFIT - CH-47976. Dealers still can test the fuel injectors without an AFIT. Refer to Fuel Injector Diagnosis (W/ J 39021 or Tech 2(R)) in SI.

As mentioned in the AFIT User Guide, vehicles that are not listed in the AFIT menu can still be tested with the AFIT. Depending on the model, it
may be possible to enter the previous model year and proceed with testing using the DLC connection. If this is not possible on the model that you
are working on, it will be necessary to use the direct connection method outlined in the AFIT User Guide (See Pages 17-31).

General Motors recommends that the Active Fuel Injector Tester (AFIT) be used in testing fuel injectors. If the SI diagnostics do not isolate a cause
for this concern, use the Active Fuel Injector Tester (AFIT - CH-47976) to perform an Injector Test as outlined in the AFIT User Guide.

The AFIT Injector Test measures the flow characteristics of all fuel injectors, which is more precise when compared with the standard Tech 2(R)
fuel injector balance test. As a result, the AFIT is more likely to isolate the cause of a P1174 DTC (for example: if it is being caused by a fuel
injector concern).

The CH-47976 (Active Fuel Injector Tester - AFIT) can also be used to measure fuel pressure and fuel system leak down. Also, as mentioned in the
P1174 SI diagnosis, if the misfire current counters or misfire graph indicate any misfires, it may be an indicator of the cylinder that is causing the
concern. Refer to Fuel Injector Diagnosis (w/CH-47976) in SI for additional instructions.

To access the training video on AFIT, take the following path at the GM Training Website:

After logging into the gmtraining.com website, choose the link on the left side of the page titled web video library.

Then choose "technical".

Next, within the search box, type in September course number 10206.09D.

This will bring up a link with this course. Scroll through to choose feature topic."

At this point, the seminar can be chosen to view or the video related to the AFIT.

Additional training is available from the gmtraining.com website. Please see TECHassist 16044.18T2 Active Fuel Injector Tester and also see
16043.51D Engine Mechanical Diagnosis & Measurement for more information on GM Upper Engine and Fuel Injector Cleaner.

Also, dealers can now download software updates for the AFIT at GM Dealer Equipment (GMDE) on the web at http://www.gmde.net/AFIT.cfm.

To access the training video on AFIT, take the following path at the GMPro LMS Training Website:

After logging into the <www.gmprocanada.com> website, choose the link on the left side of the page titled "Catalog."

Then choose "Catalog Search."

Next, within the search box, Select Course Number - Contains - "T" then select search.

This will bring up a list of TECHassist courses. Scroll through to choose "Active Fuel Injector Tester" and select "View."

At this point, a new window will open and the program can be Launched.

Also, dealers can now download software updates for the AFIT at GM Dealer Equipment (GMDE) on the web at
http://www.gmde.net/softwareupdates/.

Additional information can be found on AFIT (June 2006 Edition) and GM Upper Engine and Fuel Injector Cleaner (November 2006 Edition) in
Techlink. To access the articles, take the following path:

Go to GM DealerWorld (U.S.) or the GM infoNET (Canada).

Click on the Service Tab in DealerWorld (GM infoNET for Canada).

Click on the GM Techlink Hyperlink.

Click on the Archives Hyperlink at GM Techlink.


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 182
Chevrolet Venture V6-3.4L VIN E 2507

Click on 06-2006 in the Archives Section and Click on the Active Fuel Injector Tester Link in the June 2006 Techlink Article.

Click on 11-2006 in the Archives Section and Click on the GM Top Engine Cleaner Replaced Link in the November 2006 Techlink Article.

GM UPPER ENGINE AND FUEL INJECTOR CLEANER is the only injector cleaning agent recommended. DO NOT USE OTHER CLEANING
AGENTS AS THEY MAY CONTAIN METHANOL, WHICH CAN DAMAGE FUEL SYSTEM COMPONENTS. Under NO circumstances
should the GM Upper Engine and Fuel Injector Cleaner be added to the vehicle fuel tank.

Do not exceed the recommended cleaning solution concentration. Testing has demonstrated that exceeding the recommended cleaning solution
concentration does not improve the effectiveness of this procedure.

Vehicles with less than 160 km (100 mi) on the odometer should not have the injectors cleaned. These vehicles should have any out of specification
injectors replaced.

For 4, 5 and 6 cylinder engines, empty two of the 30 ml (1 oz) reservoirs of the GM Upper Engine and Fuel Injector Cleaner container into the J
35800-A - Injector Cleaning Tank then add 420 ml (14 oz) of regular unleaded gasoline. If you are using any other brand of cleaning tank, you will
need a total of 60 ml (2 oz) mixed with 420 ml (14 oz) of regular unleaded gasoline.

For 8 cylinder engines, empty two of the 30 ml (1 oz) reservoirs of the GM Upper Engine and Fuel Injector Cleaner container into the J 35800-A -
Injector Cleaning Tank then add 420 ml (14 oz) of regular unleaded gasoline. If you are using any other brand of cleaning tank, you will need a
total of 60 ml (2 oz) of Upper Engine and Fuel Injector Cleaner mixed with 420 ml (14 oz) of regular unleaded gasoline. This procedure will need
to be repeated for a second time for an 8 cylinder engine (8 cylinder engines receive 960 ml total fluid - 120 ml (4 oz) of Upper Engine and Fuel
Injector Cleaner and 840 ml (28 oz) of gasoline.

Be sure to follow all additional instructions provided with the tool.

Electrically disable the vehicle fuel pump by removing the fuel pump relay and disconnecting the oil pressure switch connector, if equipped.

Turn the ignition to the OFF position.

Relieve fuel pressure and disconnect the fuel feed and return lines at the fuel rail. Plug the fuel feed and return lines coming off the fuel rail with J
37287, J 42873 or J 42964 as appropriate for the fuel system.

Connect the J 35800-A to the vehicle fuel rail.

Pressurize the J 35800-A to 510 kPa (75 psi).

Start and idle the engine until it stalls, due to lack of fuel. This should take approximately 15-20 minutes.

Turn the ignition to the OFF position.

Disconnect the J 35800-A from the fuel rail.

Reconnect the vehicle fuel pump relay and oil pressure switch connector, if equipped.

Remove the J 37287, J 42873 or J 42964 and reconnect the vehicle fuel feed and return lines.

Start and idle the vehicle for an additional two minutes to ensure residual injector cleaner is flushed from the fuel rail and fuel lines.

Pour the entire contents of GM Fuel System Treatment Plus (P/N 88861011 [in Canada, P/N 88861012]) into the tank and advise the customer to
fill the tank.

Review the benefits of using Top Tier Detergent gasoline with the customer and recommend that they add a bottle of GM Fuel System Treatment
Plus to the fuel tank at every oil change. Regular use of GM Fuel System Treatment Plus should keep the customer from having to repeat the
injector cleaning procedure. Road test the vehicle to verify that the customer concern has been corrected.
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 183
Chevrolet Venture V6-3.4L VIN E 2508

Parts Information

Warranty Information (excluding Saab U.S. Models)

For vehicles repaired under warranty, use the table.

Warranty Information (Saab U.S. Models)


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 184
Chevrolet Venture V6-3.4L VIN E 2509

For vehicles repaired under warranty, use the table.


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 185
Chevrolet Venture V6-3.4L VIN E 2510
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 186
Chevrolet Venture V6-3.4L VIN E 2511

Injector Worksheet (Use with Tech2(R) Balance Test)

Disclaimer
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 187
Chevrolet Venture V6-3.4L VIN E 2512

Technical Service Bulletin # 03-06-04-030D Date: 070503

Fuel System - MIL ON/DTC's Set/Driveability Problems


Bulletin No.: 03-06-04-030D

Date: May 03, 2007

TECHNICAL

Subject:
Various Driveability Symptoms Due to Clogged Fuel Injectors, MIL/SES DTCs P0171, P0172, P0174, P0300, P1174, P1175 (Clean Fuel Injectors
and/or Perform Injector Test With AFIT - CH-47976)

Models

Supercede:

This bulletin is being revised to include additional service information in steps 1 and 2 under Injector Cleaning Procedure.

Please discard Corporate Bulletin Number 03-06-04-030C (Section 06 - Engine/Propulsion System).

Condition

Some customers may comment on any of the following various driveability symptoms:

Extended Crank Time

Hard to Start

MIL/SES Illuminated with DTCs

Hesitation

Lack of Power

Surge or Chuggle

Rough Idle

Light or Intermittent Misfire

Cause

Due to various factors, the fuel injectors may become restricted. Extensive testing has demonstrated that fuel related issues are the cause of clogged
injectors. At this point, no specific fuel, fuel constituent, or engine condition has been identified as causing the restriction. The restriction causes the
engine to operate at a lean air fuel ratio. This may either trigger the MIL to illuminate or the engine to develop various driveability symptoms.

Correction

Fuel injector restrictions, deposits can be cleaned on the vehicle using the following procedure. Under NO circumstances should this procedure be
modified, changed or shortened. As a long term solution, and to prevent reoccurrence, customers should be encouraged to use Top Tier Detergent
Gasoline. For further information on Top Tier detergent gasoline and fuel retailers, please refer to the following Corporate Bulletin Numbers:

04-06-04-047G (U.S. Only)

05-06-04-022C (Canada ONLY)


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 188
Chevrolet Venture V6-3.4L VIN E 2513

GM UPPER ENGINE AND FUEL INJECTOR CLEANER is the only injector cleaning agent approved for use with General Motors fuel system
components. Other injector cleaners may cause damage to plastics, plated metals or bearings. General Motors has completed extensive laboratory
testing of GM Upper Engine and Fuel Injector Cleaner, and can assure its compatibility with General Motors fuel system components, as long as
the cleaning procedure is followed correctly.

The following tools, or their equivalent, are required:

CH-47976 Active Fuel Injector Tester (AFIT)

J 35800-A Fuel Injector Cleaner

J 37287 Fuel Line Shut-off Adapter

J 42964 Fuel Line Shut-off Adapter

J 42873 Fuel Line Shut-off Adapter

* One bottle of GM Upper Engine and Fuel Injector Cleaner, P/N 88861802 (in Canada, P/N 88861804)

* One bottle of GM Fuel System Treatment Plus, P/N 88861011 (in Canada, P/N 88861012)

Some dealers may not have an Active Fuel Injector Tester (AFIT- CH-47976). Dealers can contact 1-800-GM-TOOLS (1-800-468-6657) to order
an AFIT - CH-47976. Dealers still can test the fuel injectors without an AFIT. Refer to Fuel Injector Diagnosis (w/J 39021 or Tech 2(R)) in SI.

As mentioned in the AFIT User Guide, vehicles that are not listed in the AFIT menu can still be tested with the AFIT. Depending on the model, it
may be possible to enter the previous model year and proceed with testing using the DLC connection. If this is not possible on the model that you
are working on, it will be necessary to use the direct connection method outlined in the AFIT User Guide (See Pages 17-31).

General Motors recommends that the Active Fuel Injector Tester (AFIT) be used in testing fuel injectors. If the SI diagnostics do not isolate a cause
for this concern, use the Active Fuel Injector Tester (AFIT - CH-47976) to perform an Injector Test as outlined in the AFIT User Guide.

The AFIT Injector Test measures the flow characteristics of all fuel injectors, which is more precise when compared with the standard Tech 2(R)
fuel injector balance test. As a result, the AFIT is more likely to isolate the cause of a P1174 DTC (for example: if it is being caused by a fuel
injector concern).

The CH-47976 (Active Fuel Injector Tester - AFIT can also be used to measure fuel pressure and fuel system leak down. Also, as mentioned in the
P1174 SI diagnosis, if the misfire current counters or misfire graph indicate any misfires, it may be an indicator of the cylinder that is causing the
concern. Refer to Fuel Injector Diagnosis (w/CH-47976) in SI for additional instructions.

To access the training video on AFIT, take the following path at the GM Training Website:

After logging into the gmtraining.com website, choose the link on the left side of the page titled web video library.

Then choose "technical".

Next, within the search box, type in September course number 10206.09D.

This will bring up a link with this course. Scroll through to choose feature topic."

At this point, the seminar can be chosen to view or the video related to the AFIT.

Additional training is available from the gmtraining.com website. Please see TECHassist 16044.18T2 Active Fuel Injector Tester and also see
16043.51D Engine Mechanical Diagnosis & Measurement for more information on GM Upper Engine and Fuel Injector Cleaner.

Also, dealers can now download software updates for the AFIT at GM Dealer Equipment (GMDE) on the web at http://www.gmde.net/AFIT.cfm.

To access the training video on AFIT, take the following path at the GMPro LMS Training Website:

After logging into the <www.gmprocanada.com> website, choose the link on the left side of the page titled "Catalog."

Then choose "Catalog Search."

Next, within the search box, Select Course Number - Contains - "T" then select search.

This will bring up a list of TECHassist courses. Scroll through to choose "Active Fuel Injector Tester" and select "View."

At this point, a new window will open and the program can be Launched.

Also, dealers can now download software updates for the AFIT at GM Dealer Equipment (GMDE) on the web at
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 189
Chevrolet Venture V6-3.4L VIN E 2514
http://www.gmde.net/softwareupdates/.

Additional information can be found on AFIT (June 2006 Edition) and GM Upper Engine and Fuel Injector Cleaner (November 2006 Edition) in
Techlink.

To access the articles, take the following path:

Go to GM DealerWorld (U.S.) or the GM infoNET (Canada).

Click on the Service Tab in DealerWorld (GM infoNET for Canada).

Click on the GM Techlink Hyperlink.

Click on the Archives Hyperlink at GM Techlink.

Click on 06-2006 in the Archives Section and Click on the Active Fuel Injector Tester Link in the June 2006 Techlink Article.

Click on 11-2006 in the Archives Section and Click on the GM Top Engine Cleaner Replaced Link in the November 2006 Techlink Article.

GM UPPER ENGINE AND FUEL INJECTOR CLEANER is the only injector cleaning agent recommended. DO NOT USE OTHER CLEANING
AGENTS AS THEY MAY CONTAIN METHANOL, WHICH CAN DAMAGE FUEL SYSTEM COMPONENTS. Under NO circumstances
should the GM Upper Engine and Fuel Injector Cleaner be added to the vehicle fuel tank.

Do not exceed the recommended cleaning solution concentration. Testing has demonstrated that exceeding the recommended cleaning solution
concentration does not improve the effectiveness of this procedure.

Vehicles with less than 160 km (100 mi) on the odometer should not have the injectors cleaned. These vehicles should have any out of specification
injectors replaced.

For 4, 5 and 6 cylinder engines, empty two of the 30 ml (1 oz) reservoirs of the GM Upper Engine and Fuel Injector Cleaner container into the J
35800-A - Injector Cleaning Tank then add 420 ml (14 oz) of regular unleaded gasoline. If you are using any other brand of cleaning tank, you will
need a total of 60 ml (2 oz) mixed with 420 ml (14 oz) of regular unleaded gasoline.

For 8 cylinder engines, empty two of the 30 ml (1 oz) reservoirs of the GM Upper Engine and Fuel Injector Cleaner container into the J 35800-A -
Injector Cleaning Tank then add 420 ml (14 oz) of regular unleaded gasoline. If you are using any other brand of cleaning tank, you will need a
total of 60 ml (2 oz) of Upper Engine and Fuel Injector Cleaner mixed with 420 ml (14 oz) of regular unleaded gasoline. This procedure will need
to be repeated for a second time for an 8 cylinder engine (8 cylinder engines receive 960 ml total fluid - 120 ml (4 oz) of Upper Engine and Fuel
Injector Cleaner and 840 ml (28 oz) of gasoline.

Fill the injector cleaning tank with regular unleaded gasoline. Be sure to follow all additional instructions provided with the tool.

Electrically disable the vehicle fuel pump by removing the fuel pump relay and disconnecting the oil pressure switch connector, if equipped.

Turn the ignition to the OFF position.

Relieve fuel pressure and disconnect the fuel feed and return lines at the fuel rail. Plug the fuel feed and return lines coming off the fuel rail with J
37287, J 42873 or J 42964 as appropriate for the fuel system.

Connect the J 35800-A to the vehicle fuel rail.

Pressurize the J 35800-A to 510 kPa (75 psi).

Start and idle the engine until it stalls, due to lack of fuel. This should take approximately 15-20 minutes.

Turn the ignition to the OFF position.

Disconnect the J 35800-A from the fuel rail.

Reconnect the vehicle fuel pump relay and oil pressure switch connector, if equipped.

Remove the J 37287, J 42873 or J 42964 and reconnect the vehicle fuel feed and return lines.

Start and idle the vehicle for an additional two minutes to ensure residual injector cleaner is flushed from the fuel rail and fuel lines.

Pour the entire contents of GM Fuel System Treatment Plus (P/N 88861011 [in Canada, P/N 88861012]) into the tank and advise the customer to
fill the tank.

Review the benefits of using Top Tier Detergent gasoline with the customer and recommend that they add a bottle of GM Fuel System Treatment
Plus to the fuel tank at every oil change. Regular use of GM Fuel System Treatment Plus should keep the customer from having to repeat the
injector cleaning procedure. Road test the vehicle to verify that the customer concern has been corrected.
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 190
Chevrolet Venture V6-3.4L VIN E 2515

Parts Information

Warranty Information (excluding Saab U.S Models)

For vehicles repaired under warranty, use the table.

Warranty Information (Saab U.S. Models)


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 191
Chevrolet Venture V6-3.4L VIN E 2516

For vehicles repaired under warranty, use the table.


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 192
Chevrolet Venture V6-3.4L VIN E 2517
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 193
Chevrolet Venture V6-3.4L VIN E 2518
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 194
Chevrolet Venture V6-3.4L VIN E 2519

Injector Worksheet (Use with Tech2(R) Balance Test)

Disclaimer
Technical Service Bulletin # 03-06-04-030C Date: 070315

Fuel System - Various Driveability Problem/MIL ON/DTC's


Bulletin No.: 03-06-04-030C

Date: March 15, 2007

TECHNICAL

Subject:
Various Driveability Symptoms Due to Clogged Fuel Injectors, MIL/SES DTCs P0171, P0172, P0174, P0300, P1174, P1175 (Clean Fuel Injectors
and/or Perform Injector Test With AFIT - CH-47976)

Models:
2000-2007 GM Passenger Cars and Light Duty Trucks (Including Saturn)
2003-2007 HUMMER H2
2006-2007 HUMMER H3
2005-2007 Saab 9-7X

with 2.2L, 2.4L, 2.8L, 3.1L, 3.4L, 3.5L, 3.8L, 3.9L, 4.2L, 4.3L, 4.8L, 5.3L, 6.0L, 6.2L or 8.1L Engine (VINs F, D, 4, 5, T, 8, J, E, H, L, 6, K, 1, 2,
R, W, S, X, V, T, M, N, U, H, Y, 8, G - RPOs L61, LN2, L43, LD9, LK5, LG8, LA1, LNJ, LX5, LX9, LZ4, LZE, L52, L36, L67, L26, L32, LZ9,
LZ8, LGD, LL8, LU3, LR4, LM7, LH6, LQ9, LQ4, L52, L76, L92, L18)

and MULTEC(R) 2 Fuel Injectors

Supercede:

This bulletin is being revised to include the 3.9L engines, additional engine RPOs and add claim information under the Parts Information table.
Please discard Corporate Bulletin Number 03-06-04-030B (Section 06 - Engine/Propulsion System).

Condition

Some customers may comment on any of the following various driveability symptoms:

Extended Crank Time

Hard to Start

MIL/SES Illuminated with DTCs:

Hesitation

Lack of Power

Surge or Chuggle

Rough Idle

Light or Intermittent Misfire

Cause

Due to various factors, the fuel injectors may become restricted. Extensive testing has demonstrated that fuel related issues are the cause of clogged
injectors. At this point, no specific fuel, fuel constituent, or engine condition has been identified as causing the restriction. The restriction causes the
engine to operate at a lean air fuel ratio. This may either trigger the MIL to illuminate or the engine to develop various driveability symptoms.

Correction
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 195
Chevrolet Venture V6-3.4L VIN E 2520

Fuel injector restrictions, deposits can be cleaned on the vehicle using the following procedure. Under NO circumstances should this procedure be
modified, changed or shortened. As a long term solution, and to prevent reoccurrence, customers should be encouraged to use Top Tier Detergent
Gasoline. For further information on Top Tier detergent gasoline and fuel retailers, please refer to the following Corporate Bulletin Numbers:

04-06-04-047G (U.S. Only)


05-06-04-022C (Canada ONLY)

GM UPPER ENGINE AND FUEL INJECTOR CLEANER is the only injector cleaning agent approved for use with General Motors fuel system
components. Other injector cleaners may cause damage to plastics, plated metals or bearings. General Motors has completed extensive laboratory
testing of GM Upper Engine and Fuel Injector Cleaner, and can assure its compatibility with General Motors fuel system components, as long as
the cleaning procedure is followed correctly.

Injector Cleaning Procedure

The following tools, or their equivalent, are required:

CH-47976 Active Fuel Injector Tester (AFIT)

J 35800-A Fuel Injector Cleaner

J 37287 Fuel Line Shut-off Adapter

J 42964 Fuel Line Shut-off Adapter

J 42873 Fuel Line Shut-off Adapter

* One bottle of GM Upper Engine and Fuel Injector Cleaner, P/N 88861802 (in Canada, P/N 88861804)

* One bottle of GM Fuel System Treatment Plus, P/N 88861011 (in Canada, P/N 88861012)

Active Fuel Injector Tester (AFIT- CH47976)

Some dealers may not have an Active Fuel Injector Tester (AFIT- CH-47976). Dealers can contact 1-800-GM-TOOLS (1-800-468-6657) to order
an AFIT- CH-47976. Dealers still can test the fuel injectors without an AFIT. Refer to Fuel Injector Diagnosis (W/J 39021 or Tech 2(R)) in SI.

As mentioned in the AFIT User Guide, vehicles that are not listed in the AFIT menu can still be tested with the AFIT. Depending on the model, it
may be possible to enter the previous model year and proceed with testing using the DLC connection. If this is not possible on the model that you
are working on, it will be necessary to use the direct connection method outlined in the AFIT User Guide (See Pages 17-31).

General Motors recommends that the Active Fuel Injector Tester (AFIT) be used in testing fuel injectors. If the SI diagnostics do not isolate a cause
for this concern, use the Active Fuel Injector Tester (AFIT - CH-47976) to perform an Injector Test as outlined in the AFIT User Guide.

The AFIT Injector Test measures the flow characteristics of all fuel injectors, which is more precise when compared with the standard Tech 2(R)
fuel injector balance test. As a result, the AFIT is more likely to isolate the cause of a P1174 DTC (for example: if it is being caused by a fuel
injector concern).

The CH-47976 (Active Fuel Injector Tester - AFIT) can also be used to measure fuel pressure and fuel system leak down. Also, as mentioned in the
P1174 SI diagnosis, if the misfire current counters or misfire graph indicate any misfires, it may be an indicator of the cylinder that is causing the
concern. Refer to Fuel Injector Diagnosis (w/CH-47976) in SI for additional instructions.

Training (U.S.)

To access the training video on AFIT, take the following path at the GM Training Website:

After logging into the gmtraining.com website, choose the link on the left side of the page titled "web video library".

Then choose "technical".

Next, within the search box, type in September course number 10206.09D.

This will bring up a link with this course. Scroll through to choose "feature topic".

At this point, the seminar can be chosen to view or the video related to the AFIT.

Additional training is available from the gmtraining.com website. Please see TECHassist 16044.18T2 Active Fuel Injector Tester and also see
16043.51D Engine Mechanical Diagnosis & Measurement for more information on GM Upper Engine and Fuel Injector Cleaner.

Training (Canada)
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 196
Chevrolet Venture V6-3.4L VIN E 2521

To access the training video on AFIT, take the following path at the GMPro LMS Training Website:

After logging into the <www.gmprocanada.com> website, choose the link on the left side of the page titled "Catalog."

Then choose "Catalog Search."

Next, within the search box, Select Course Number - Contains - "T" then select search.

This will bring up a list of TECHassist courses. Scroll through to choose "Active Fuel Injector Tester" and select "View."

At this point, a new window will open and the program can be Launched.

Techlink

Additional information can be found on AFIT (June 2006 Edition) and GM Upper Engine and Fuel Injector Cleaner (November 2006 Edition) in
Techlink. To access the articles, take the following path:

Go to GM DealerWorld (U.S.) or the GM infoNET (Canada).

Click on the Service Tab in DealerWorld (GM infoNET for Canada).

Click on the GM Techlink Hyperlink.

Click on the Archives Hyperlink at GM Techlink.

Click on 06-2006 in the Archives Section and Click on the Active Fuel Injector Tester Link in the June 2006 Techlink Article.

Click on 11-2006 in the Archives Section and Click on the GM Top Engine Cleaner Replaced Link in the November 2006 Techlink Article.

Injector Cleaning Procedure

GM UPPER ENGINE AND FUEL INJECTOR CLEANER is the only injector cleaning agent recommended. DO NOT USE OTHER CLEANING
AGENTS AS THEY MAY CONTAIN METHANOL, WHICH CAN DAMAGE FUEL SYSTEM COMPONENTS. Under NO circumstances
should the GM Upper Engine and Fuel Injector Cleaner be added to the vehicle fuel tank.

Do not exceed the recommended cleaning solution concentration. Testing has demonstrated that exceeding the recommended cleaning solution
concentration does not improve the effectiveness of this procedure.

Vehicles with less than 160 km (100 mi) on the odometer should not have the injectors cleaned. These vehicles should have any out of specification
injectors replaced.

For 4, 5 and 6 cylinder engines, empty two of the 30 ml (1 oz) reservoirs of the GM Upper Engine and Fuel Injector Cleaner container into the J
35800-A, injector cleaning tank. If you are using any other brand of cleaning tank, you will need a total of 60 ml (2 oz) mixed with 420 ml (14 oz)
of regular unleaded gasoline.

For 8 cylinder engines, empty two of the 30 ml (1 oz) reservoirs of the GM Upper Engine and Fuel Injector Cleaner container into the J 35800-A,
injector cleaning tank. If you are using any other brand of cleaning tank, you will need a total of 60 ml (2 oz) of Upper Engine and Fuel Injector
Cleaner mixed with 420 ml (14 oz) of regular unleaded gasoline. This procedure will need to be repeated for a second time for an 8 cylinder engine
(8 cylinder engines receive 960 ml total fluid - 120 ml (4 oz) of Upper Engine and Fuel Injector Cleaner and 840 ml (28 oz) of gasoline.

Fill the injector cleaning tank with regular unleaded gasoline. Be sure to follow all additional instructions provided with the tool.

Electrically disable the vehicle fuel pump by removing the fuel pump relay and disconnecting the oil pressure switch connector, if equipped.

Turn the ignition to the OFF position.

Relieve fuel pressure and disconnect the fuel feed and return lines at the fuel rail. Plug the fuel feed and return lines coming off the fuel rail with J
37287, J 42873 or J 42964 as appropriate for the fuel system.

Connect the J 35800-A to the vehicle fuel rail.

Pressurize the J 35800-A to 510 kPa (75 psi).

Start and idle the engine until it stalls, due to lack of fuel. This should take approximately 15-20 minutes.

Turn the ignition to the OFF position.

Disconnect the J 35800-A from the fuel rail.


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 197
Chevrolet Venture V6-3.4L VIN E 2522

Reconnect the vehicle fuel pump relay and oil pressure switch connector, if equipped.

Remove the J 37287, J 42873 or J 42964 and reconnect the vehicle fuel feed and return lines.

Start and idle the vehicle for an additional two minutes to ensure residual injector cleaner is flushed from the fuel rail and fuel lines.

Pour the entire contents of GM Fuel System Treatment Plus (P/N 88861011 [in Canada, P/N 88861012]) into the tank and advise the customer to
fill the tank.

Review the benefits of using Top Tier Detergent gasoline with the customer and recommend that they add a bottle of GM Fuel System Treatment
Plus to the fuel tank at every oil change. Regular use of GM Fuel System Treatment Plus should keep the customer from having to repeat the
injector cleaning procedure.

Road test the vehicle to verify that the customer concern has been corrected.

Parts Information

Warranty Information (excluding Saab U.S. Models)


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 198
Chevrolet Venture V6-3.4L VIN E 2523

For vehicles repaired under warranty, use the table.

Warranty Information (Saab U.S. Models)


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 199
Chevrolet Venture V6-3.4L VIN E 2524

For vehicles repaired under warranty, use the table.


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 200
Chevrolet Venture V6-3.4L VIN E 2525

Injector Worksheet (Use with Tech 2(R) Balance Test)

Disclaimer
Technical Service Bulletin # 04-06-04-036B Date: 060512
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 201
Chevrolet Venture V6-3.4L VIN E 2526
Engine Controls - Reprogramming Warranty Coverage
This TSB number 04-06-04-036B, dated 05/12/06 has been superceded by TSB number 04-06-04-036E , dated 05/08/08
Technical Service Bulletin # 04-06-04-036A Date: 060403

Engine Controls - Programming Warranty Coverage


This TSB number 04-06-04-036A, dated 04/03/06 has been superceded by TSB number 04-06-04-036E , dated 05/08/08
Technical Service Bulletin # 02-07-30-001D Date: 051202

A/T Controls - DTCs P0894/P1870 Diagnostics


This TSB number 02-07-30-001D, dated 12/02/05 has been superceded by TSB number 02-07-30-001G , dated 03/19/08
Technical Service Bulletin # 01-08-45-005D Date: 051202

Electrical - No Start/Warning Lamps ON/Poss. DTC's


This TSB number 01-08-45-005D, dated 12/02/05 has been superceded by TSB number 01-08-45-005E , dated 08/29/06
Technical Service Bulletin # 00-06-04-033A Date: 050825

Emissions - OBDII I/M Readiness Test


This TSB number 00-06-04-033A, dated 08/25/05 has been superceded by TSB number 00-06-04-033B , dated 10/10/06
Technical Service Bulletin # 02-07-30-001C Date: 050531

A/T - DTC's P0894 and P01870 Diagnostic Information


This TSB number 02-07-30-001C, dated 05/31/05 has been superceded by TSB number 02-07-30-001G , dated 03/19/08
Technical Service Bulletin # 01-08-45-005C Date: 050502

Electrical - Hard Start/MIL ON/Various DTC's Set


This TSB number 01-08-45-005C, dated 05/02/05 has been superceded by TSB number 01-08-45-005E , dated 08/29/06
Technical Service Bulletin # 01-07-30-036C Date: 040302

A/T - DTC P0756 Diagnostic Tips


This TSB number 01-07-30-036C, dated 03/02/04 has been superceded by TSB number 01-07-30-036H , dated 01/29/09
Technical Service Bulletin # 02-07-30-001A Date: 040211

A/T - 4L60E and 4L65E DTC P0894/P1870 Diagnostics


This TSB number 02-07-30-001A, dated 02/11/04 has been superceded by TSB number 02-07-30-001G , dated 03/19/08
Technical Service Bulletin # 01-07-30-038B Date: 040126

A/T - 4L60-E/4L65-E MIL ON/DTC P0757/Slipping


This TSB number 01-07-30-038B, dated 01/26/04 has been superceded by TSB number 01-07-30-038D , dated 09/12/06
Technical Service Bulletin # 01-08-45-005A Date: 030401

Electrical - Multiple Lamp Illumination/DTC's Set


This TSB number 01-08-45-005A, dated 04/01/03 has been superceded by TSB number 01-08-45-005E , dated 08/29/06
Technical Service Bulletin # 03-06-04-012 Date: 030101

Electrical - Wiring Harness Inspection Recommendations


This TSB number 03-06-04-012, dated 01/01/03 has been superceded by TSB number 03-06-04-012A , dated 08/10/05
Technical Service Bulletin # 02-07-30-022 Date: 020501

A/T - SES Lamp ON/Multiple DTC's Set/Harsh Shifts


This TSB number 02-07-30-022, dated 05/01/02 has been superceded by TSB number 02-07-30-022B , dated 10/20/03
Technical Service Bulletin # 00-07-30-007 Date: 000501

A/T - MIL ON/P0741 & P0742/Whine in Park/Neutral


This TSB number 00-07-30-007, dated 05/01/00 has been superceded by TSB number 00-07-30-007A , dated 02/01/02
Technical Service Bulletin # 00-06-04-037A Date: 011101

A/T - Harsh Shifts/MIL ON/DTC's P0716/P0717 Set


This TSB number 00-06-04-037A, dated 11/01/01 has been superceded by TSB number 02-07-30-022B , dated 10/20/03
Technical Service Bulletin # 99-06-03-010 Date: 991001

PCM/BCM - DTC's B1001, B1271 or B1780 Set


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 202
Chevrolet Venture V6-3.4L VIN E 2527
This TSB number 99-06-03-010, dated 10/01/99 has been superceded by TSB number 99-06-03-010A , dated 06/01/01
Technical Service Bulletin # 02-06-05-004A Date: 040109

Emissions - Catalytic Converter Damage/Misfire Codes Set


This TSB number 02-06-05-004A, dated 01/09/04 has been superceded by TSB number 02-06-05-004B , dated 02/14/06
Technical Service Bulletin # 05-06-02-001 Date: 050224

Cooling System - Aluminum Radiator/Heater Core Info.


This TSB number 05-06-02-001, dated 02/24/05 has been superceded by TSB number 05-06-02-001A , dated 07/16/08
Technical Service Bulletin # 99-07-30-016A Date: 020901

A/T - Intermittent Downshift Slip/Busyness/Cycling


This TSB number 99-07-30-016A, dated 09/01/02 has been superceded by TSB number 99-07-30-016B , dated 10/01/02
Technical Service Bulletin # 04-06-01-029D Date: 091211

Vehicle - Engine Crankcase and Subsystems Flushing Info.


This TSB number 04-06-01-029D, dated 12/11/09 has been superceded by TSB number 04-06-01-029E , dated 04/29/10
Technical Service Bulletin # 04-06-01-029C Date: 091119

Vehicle - Engine/Subsystem Flushing Recommendations


This TSB number 04-06-01-029C, dated 11/19/09 has been superceded by TSB number 04-06-01-029E , dated 04/29/10
Technical Service Bulletin # 04-06-01-029B Date: 080205

Engine - Crankcase Flushing Information


This TSB number 04-06-01-029B, dated 02/05/08 has been superceded by TSB number 04-06-01-029E , dated 04/29/10
Technical Service Bulletin # 05-06-01-010A Date: 070416

Engine - Sealant Usage/procedures


This TSB number 05-06-01-010A, dated 04/16/07 has been superceded by TSB number 05-06-01-010B , dated 09/28/07
Technical Service Bulletin # 00-06-01-012B Date: 060118

Engine - Surface Conditioning Disc Usage Prohibition


This TSB number 00-06-01-012B, dated 01/18/06 has been superceded by TSB number 00-06-01-012C , dated 04/14/08
Technical Service Bulletin # 05-06-01-010 Date: 050307

Engine - Sealant Usage Recommendations


This TSB number 05-06-01-010, dated 03/07/05 has been superceded by TSB number 05-06-01-010B , dated 09/28/07
Technical Service Bulletin # 00-06-01-012 Date: 000501

Gasket Surfaces - Use of Surface Conditioning Discs


This TSB number 00-06-01-012, dated 05/01/00 has been superceded by TSB number 00-06-01-012C , dated 04/14/08
Technical Service Bulletin # 03-06-01-010B Date: 031024

Engine - Intake Manifold Oil/Coolant Leak


This TSB number 03-06-01-010B, dated 10/24/03 has been superceded by TSB number 03-06-01-010C , dated 04/08/08
Technical Service Bulletin # 03-06-01-010A Date: 030408

Engine - Oil/Coolant Leaks


This TSB number 03-06-01-010A, dated 04/08/03 has been superceded by TSB number 03-06-01-010C , dated 04/08/08
Technical Service Bulletin # 03-06-01-010 Date: 030301

Engine - Oil or Coolant Leaks


This TSB number 03-06-01-010, dated 03/01/03 has been superceded by TSB number 03-06-01-010C , dated 04/08/08
Technical Service Bulletin # 05-06-01-019E Date: 070529

Engine - Oil Leaks From Crankshaft Rear Main Seal


This TSB number 05-06-01-019E, dated 05/29/07 has been superceded by TSB number 05-06-01-019F , dated 10/02/07
Technical Service Bulletin # 05-06-01-019D Date: 060512

Engine - Rear Crankshaft Main Seal Oil Leaks


This TSB number 05-06-01-019D, dated 05/12/06 has been superceded by TSB number 05-06-01-019F , dated 10/02/07
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 203
Chevrolet Venture V6-3.4L VIN E 2528
Technical Service Bulletin # 05-06-01-019C Date: 060317

Engine - Oil Leaks From The Rear Main Seal


This TSB number 05-06-01-019C, dated 03/17/06 has been superceded by TSB number 05-06-01-019F , dated 10/02/07
Technical Service Bulletin # 05-06-01-019B Date: 051206

Engine - Rear Main Seal Oil Leakage


This TSB number 05-06-01-019B, dated 12/06/05 has been superceded by TSB number 05-06-01-019F , dated 10/02/07
Technical Service Bulletin # 05-06-01-019A Date: 050922

Engine - Rear Main Seal Oil Leaks


This TSB number 05-06-01-019A, dated 09/22/05 has been superceded by TSB number 05-06-01-019F , dated 10/02/07
Technical Service Bulletin # 05-06-01-019 Date: 050617

Engine - Rear Crankshaft Seal Oil Leaks


This TSB number 05-06-01-019, dated 06/17/05 has been superceded by TSB number 05-06-01-019F , dated 10/02/07
Technical Service Bulletin # 00-06-01-026B Date: 070621

Intake Manifold - Inspect/Replace After Engine Damage


This TSB number 00-06-01-026B, dated 06/21/07 has been superceded by TSB number 00-06-01-026C , dated 02/03/10
Technical Service Bulletin # 05-00-89-072A Date: 071016

Engine/Fuel - Additive Information


This TSB number 05-00-89-072A, dated 10/16/07 has been superceded by TSB number 05-00-89-072B , dated 06/17/08
Technical Service Bulletin # 03-07-29-004D Date: 071017

Manual Transmission - Operating Characteristics


This TSB number 03-07-29-004D, dated 10/17/07 has been superceded by TSB number 03-07-29-004F , dated 07/29/09
Technical Service Bulletin # 01-06-01-011D Date: 070403

Engine - Oil Consumption Guideline Info.


This TSB number 01-06-01-011D, dated 04/03/07 has been superceded by TSB number 01-06-01-011E , dated 12/18/08
Technical Service Bulletin # 05-00-89-072 Date: 051024

Engine/Fuel System - Oil/Fuel Additive Recommendations


This TSB number 05-00-89-072, dated 10/24/05 has been superceded by TSB number 05-00-89-072B , dated 06/17/08
Technical Service Bulletin # 01-06-01-011B Date: 050808

Engine - Oil Consumption Guideline Information


This TSB number 01-06-01-011B, dated 08/08/05 has been superceded by TSB number 01-06-01-011E , dated 12/18/08
Technical Service Bulletin # 01-06-01-011A Date: 030723

Engine - Oil Consumption Information


This TSB number 01-06-01-011A, dated 07/23/03 has been superceded by TSB number 01-06-01-011E , dated 12/18/08
Technical Service Bulletin # 02-06-01-003A Date: 071022

Engine - Revised Head Bolt Torque/Tightening Procedure


This TSB number 02-06-01-003A, dated 10/22/07 has been superceded by TSB number 02-06-01-003B , dated 04/15/08
Technical Service Bulletin # 00-06-01-026A Date: 040614

Engine - New Long Block Installation Precaution


This TSB number 00-06-01-026A, dated 06/14/04 has been superceded by TSB number 00-06-01-026C , dated 02/03/10
Technical Service Bulletin # 01-06-01-010A Date: 010601

Engine - Polymer Service Pistons


File In Section: 06 - Engine/Propulsion System

Bulletin No.: 01-06-01-O10A

Date: June, 2001

INFORMATION
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 204
Chevrolet Venture V6-3.4L VIN E 2529

Subject:
Polymer Service Pistons

Models:
1996 Buick Regal
1996-98 Buick Skylark
1996-01 Buick Century
1996 Chevrolet Beretta, Corsica
1996-01 Chevrolet Lumina, Monte Carlo
1997-01 Chevrolet Malibu
2000-01 Chevrolet Impala, Venture
1996-98 Oldsmobile Achieva
1996-99 Oldsmobile Cutlass
2000-01 Oldsmobile Alero, Silhouette
1996-98 Pontiac Grand Am
1996-01 Pontiac Grand Prix
2000~1 Pontiac Grand Am, Montana
2001 Pontiac Aztek
with 3.1 L or 3.4 L Engine (VINs J, M, E - RP0s LGB, L82, LA1)

This bulletin is being revised to clarify the models and parts information. Please discard Corporate Bulletin Number 01-06-01-010 (Section 06 -
Engine/Propulsion System).

Service pistons with polymer coated piston skirts are available for the above engines. Polymer pistons should be used in these applications any time
piston replacement is necessary.

Notice:
Do not install pistons in model years other than listed in the parts table shown. The design of the LA1 piston assembly is unique to those model
years listed. Damage to the piston, cylinder block or cylinder head may occur if the wrong piston is installed.

Refer to Corporate Service Bulletin Number 01-06-01-002 for revised piston pin installation procedure.

Parts Information

Parts are currently available from GMSPO.

DISCLAIMER
Technical Service Bulletin # 01-06-01-010 Date: 010301

Engine - Polymer Coated Pistons Available


File In Section: 06 - Engine/Propulsion System

Bulletin No.: 01-06-01-010

Date: March, 2001

INFORMATION

Subject:
Polymer Service Pistons

Models:
1996 Buick Regal
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 205
Chevrolet Venture V6-3.4L VIN E 2530
1996-98 Buick Skylark
1996-01 Buick Century
1996-01 Chevrolet Lumina, Monte Carlo
1997-01 Chevrolet Malibu
2000-01 Chevrolet Impala, Venture
1996-98 Oldsmobile Achieva
1996-99 Oldsmobile Cutlass
2000-01 Oldsmobile Alero, Silhouette
1996-01 Pontiac Grand Am, Grand Prix
2000-01 Pontiac Montana
2001 Pontiac Aztek
with 3.1 L or 3.4 L Engine (VINs J, M, E - RPOs LG8, L82, LA1)

Service pistons with polymer coated piston skirts are available for the above engines. Polymer pistons should be used in these applications any time
piston replacement is necessary.

Refer to Corporate Service Bulletin Number 01-06-01-002 for revised piston pin installation procedure.

Parts Information

Parts are currently available from GMSPO.

DISCLAIMER
Technical Service Bulletin # 01-06-01-002 Date: 010101

Piston Pin - Installation/Removal Revision


File In Section: 06 - Engine/Propulsion System

Bulletin No.: 01-06-01-002

Date: January, 2001

SERVICE MANUAL UPDATE

Subject:
Revised Piston Pin Removal/Installation Procedures

Models:
1994-96 Buick Regal
1994-98 Buick Skylark
1994-01 Buick Century
1994-95 Chevrolet Beretta, Corsica
1994-01 Chevrolet Lumina
1995-01 Chevrolet Monte Carlo
1996-01 Chevrolet Venture
1997-01 Chevrolet Malibu
2000-01 Chevrolet Impala
1994-98 Oldsmobile Achieva
1994-99 Oldsmobile Cutlass
1996-01 Oldsmobile Silhouette
1999-01 Oldsmobile Alero
1994-01 Pontiac Grand Am, Grand Prix
1996-99 Pontiac Trans Sport
1999-01 Pontiac Montana
2001 Pontiac Aztek
with 3.1L or 3.4L Engine (VINs J, M, E - RPOs LG8, L82, LA1)
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 206
Chevrolet Venture V6-3.4L VIN E 2531

This bulletin is being issued to revise the piston and rod assembly removal/installation procedures in the Engine Section of the Service Manual.

Revised Service Procedure

The following steps are provided to assist in the replacement of the piston assemblies.

Tools Required
^ J 24086 Connecting Rod Press
^ J 24086-C Piston Pin Remover/Installer
^ Connecting Rod Oven (Rod Kiln)

Disclaimer
Piston and Connecting Rod Disassemble
Important:
Prior to piston/connecting rod removal, mark or identify the piston/connecting rod assembly, and its orientation to the front of the engine,
before removal.

1. Remove the pistons from the engine following the instructions found in the Engine Repair Section of the Service Manual.

Notice:
A rod kiln MUST be used during assembly of the connecting rod to the piston. If a connecting rod kiln is not available, seek the assistance of a
reputable machine shop with a kiln. Under NO circumstances should an acetylene torch or other uncontrolled heating device be used on
connecting rods, as permanent damage to the connecting rod may result.

Important:
It is not necessary to replace the piston rings, unless they were damaged during the repair process. If the piston rings are to be reused, mark or
identify the location/order of the rings as they correspond to location on the piston being serviced. Refer to ring gap placement instructions
found in the Engine Repair Section of the Service Manual.

2. Using piston ring pliers, remove the piston rings from the piston.
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 207
Chevrolet Venture V6-3.4L VIN E 2532

3. Install the J 24086-310 fork insert into the J 24086-10 fixture support assembly.

4. Install the piston and connecting rod assembly onto the J 24086-10.

5. Install the J 24086-107 adapter onto the piston pin, and install the J 24086-88A through the J 24086-10 and onto the J 24086-107.

Important:
The piston and pin are a matched set and are not to be serviced separately.

6. Press the piston pin from the piston and connecting rod assembly.
Piston and Connecting Rod Assemble

1. Install the J 24086-310 fork insert into the J 24086-10 fixture support assembly.
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 208
Chevrolet Venture V6-3.4L VIN E 2533

2. Adjust the J 24086-9 installation pin to the following setting: G-7.

Caution:
Avoid contact with HOT components. Wear safety glasses and protective heat gloves to avoid personal injury!

Notice:
Applying excessive heat to the connecting rod may damage or distort the connecting rod or piston. Connecting rod temperatures should not
exceed 320°C (612°F).

3. Using a connecting rod kiln, heat the piston pin end of the connecting rod to 320°C (612°F).

4. Refer to the above illustration. Assemble the piston, the connecting rod, and the J 24086-6A adapter as shown. Insert the piston and
connecting rod assembly into the J 24086-10 fixture support assembly.

Notice:
After the J 24086-9 installation pin bottoms on the J 24086-10 fixture support assembly, do not exceed a pressure of 35,000 kPa (5,000 psi), or
damage to the connecting rod press may result.

5. Refer to the above illustration. Install the J 24086-105 (2) onto the piston pin. Position the J 24086-9 (1) though the J 24086-10 fixture
support assembly and onto the J 24086-105 (2).

6. Press the J 24086-9 (1) installation pin until it bottoms on the J 24086-10 fixture support assembly.
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 209
Chevrolet Venture V6-3.4L VIN E 2534

7. Reinstall the piston rings onto the new piston. Refer to the Engine Repair Section of the Service Manual for proper ring gap positioning.

8. Refer to the above illustration. Install the assembled piston and rod assembly into the engine. Verify that the directional arrows on the top of
the piston point to the front of the engine.

9. Follow the remaining engine assembly instructions found in the Engine Mechanical Section of the Service Manual.
Technical Service Bulletin # 04-06-04-051 Date: 040702

Fuel System - Injector Cleaning Recommendations


This TSB number 04-06-04-051, dated 07/02/04 has been superceded by TSB number 04-06-04-051B , dated 01/04/06
Technical Service Bulletin # 01-01-38-006 Date: 010501

A/C System - Flushing Procedures


This TSB number 01-01-38-006, dated 05/01/01 has been superceded by TSB number 01-01-38-006D , dated 09/01/04
Technical Service Bulletin # 01-01-39-003 Date: 010801

A/C - Screen Filter Kit


This TSB number 01-01-39-003, dated 08/01/01 has been superceded by TSB number 01-01-39-003A , dated 07/14/03
Technical Service Bulletin # 99-08-51-007 Date: 991001

Aluminum Wheel - Refinishing Recommendations


This TSB number 99-08-51-007, dated 10/01/99 has been superceded by TSB number 99-08-51-007D , dated 01/14/10
Technical Service Bulletin # 00-03-10-002 Date: 000301

Chrome Wheels - Chemical Staining


This TSB number 00-03-10-002, dated 03/01/00 has been superceded by TSB number 00-03-10-002E , dated 03/15/10
Technical Service Bulletin # 99-08-51-007A Date: 020301

Aluminum Wheels - Refinishing


This TSB number 99-08-51-007A, dated 03/01/02 has been superceded by TSB number 99-08-51-007D , dated 01/14/10
Technical Service Bulletin # 00-03-10-002A Date: 040408

Wheels - Chrome Wheel Chemical Staining


This TSB number 00-03-10-002A, dated 04/08/04 has been superceded by TSB number 00-03-10-002E , dated 03/15/10
Technical Service Bulletin # 00-03-10-002B Date: 040512

Wheels - Chemical Staining of Chrome Wheels


This TSB number 00-03-10-002B, dated 05/12/04 has been superceded by TSB number 00-03-10-002E , dated 03/15/10
Technical Service Bulletin # 00-03-10-002C Date: 040601

Wheels - Chemical Stains on Chrome Wheels


This TSB number 00-03-10-002C, dated 06/01/04 has been superceded by TSB number 00-03-10-002E , dated 03/15/10
Technical Service Bulletin # 04-03-10-012 Date: 040901

Wheels - Chrome Wheel Pitting/Brake Dust Accumulation


This TSB number 04-03-10-012, dated 09/01/04 has been superceded by TSB number 04-03-10-012B , dated 02/01/08
Technical Service Bulletin # 99-08-51-007B Date: 041122
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 210
Chevrolet Venture V6-3.4L VIN E 2535

Wheels - Aluminum Wheel Refinishing


This TSB number 99-08-51-007B, dated 11/22/04 has been superceded by TSB number 99-08-51-007D , dated 01/14/10
Technical Service Bulletin # 05-03-10-003 Date: 050331

Aluminum Wheels - Low Tire Pressure Condition


This TSB number 05-03-10-003, dated 03/31/05 has been superceded by TSB number 05-03-10-003F , dated 04/27/10
Technical Service Bulletin # 05-03-10-003B Date: 060413

Wheels/Tires - Slow Leaks From Aluminum Wheels


This TSB number 05-03-10-003B, dated 04/13/06 has been superceded by TSB number 05-03-10-003F , dated 04/27/10
Technical Service Bulletin # 99-08-51-007C Date: 060619

Wheels - Aluminum Wheel Refinishing Recommendations


This TSB number 99-08-51-007C, dated 06/19/06 has been superceded by TSB number 99-08-51-007D , dated 01/14/10
Technical Service Bulletin # 00-03-10-003 Date: 000801

Tires - Warranty Information Update


This TSB number 00-03-10-003, dated 08/01/00 has been superceded by TSB number 00-03-10-003B , dated 05/01/01
Technical Service Bulletin # 00-03-10-003A Date: 001001

Tires - Warranty Information


This TSB number 00-03-10-003A, dated 10/01/00 has been superceded by TSB number 00-03-10-003B , dated 05/01/01
Technical Service Bulletin # 00-03-10-006 Date: 001101

Tires - Radial Force Variation


This TSB number 00-03-10-006, dated 11/01/00 has been superceded by TSB number 00-03-10-006F , dated 05/04/10
Technical Service Bulletin # 04-03-10-001 Date: 040106

Tires - Puncture Repair Guidelines/Procedures


This TSB number 04-03-10-001, dated 01/06/04 has been superceded by TSB number 04-03-10-001F , dated 04/27/10
Technical Service Bulletin # 04-03-10-001A Date: 041130

Tires - Puncture Repair Procedures


This TSB number 04-03-10-001A, dated 11/30/04 has been superceded by TSB number 04-03-10-001F , dated 04/27/10
Technical Service Bulletin # 00-03-10-006A Date: 050617

Tires - Radial Force Variation Information


This TSB number 00-03-10-006A, dated 06/17/05 has been superceded by TSB number 00-03-10-006F , dated 05/04/10
Technical Service Bulletin # 03-03-10-007A Date: 050614

Tires - Cold Tire Flat Spotting Explanation


This TSB number 03-03-10-007A, dated 06/14/05 has been superceded by TSB number 03-03-10-007E , dated 08/05/09
Technical Service Bulletin # 00-00-90-002B Date: 050727

Tires - Proper Air Pressure Information


This TSB number 00-00-90-002B, dated 07/27/05 has been superceded by TSB number 00-00-90-002J , dated 01/28/09
Technical Service Bulletin # 00-00-90-002C Date: 050819

Tires - Proper Inflation Pressures


This TSB number 00-00-90-002C, dated 08/19/05 has been superceded by TSB number 00-00-90-002J , dated 01/28/09
Technical Service Bulletin # 04-03-10-001B Date: 060120

Tires - Puncture Repair Procedure


This TSB number 04-03-10-001B, dated 01/20/06 has been superceded by TSB number 04-03-10-001F , dated 04/27/10
Technical Service Bulletin # 01-03-10-009 Date: 011101

Wheel Nut Covers - Loose/Missing


This TSB number 01-03-10-009, dated 11/01/01 has been superceded by TSB number 01-03-10-009A , dated 07/27/04
Technical Service Bulletin # 02-07-30-052D Date: 060206
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 211
Chevrolet Venture V6-3.4L VIN E 2536
A/T - Fluid Cooler Flushing
This TSB number 02-07-30-052D, dated 02/06/06 has been superceded by TSB number 02-07-30-052F , dated 09/09/09
Technical Service Bulletin # 01-06-01-011 Date: 010301

Engine - Oil Consumption Guidelines


This TSB number 01-06-01-011, dated 03/01/01 has been superceded by TSB number 01-06-01-011E , dated 12/18/08
Technical Service Bulletin # 00-06-02-006 Date: 000801

Engine Coolant - Information


This TSB number 00-06-02-006, dated 08/01/00 has been superceded by TSB number 00-06-02-006D , dated 08/15/06
Technical Service Bulletin # 00-06-02-006A Date: 040213

Cooling System - Coolant Information


This TSB number 00-06-02-006A, dated 02/13/04 has been superceded by TSB number 00-06-02-006D , dated 08/15/06
Technical Service Bulletin # 05-06-02-002 Date: 050511

Cooling System - Coolant Dye Update Information


This TSB number 05-06-02-002, dated 05/11/05 has been superceded by TSB number 05-06-02-002B , dated 01/18/08
Technical Service Bulletin # 00-06-02-006B Date: 060330

Cooling System - DEX-COOL(R) Coolant Usage Information


This TSB number 00-06-02-006B, dated 03/30/06 has been superceded by TSB number 00-06-02-006D , dated 08/15/06
Technical Service Bulletin # 00-06-02-006C Date: 060501

Cooling System - DEX-COOL(R) Coolant Information


This TSB number 00-06-02-006C, dated 05/01/06 has been superceded by TSB number 00-06-02-006D , dated 08/15/06
Technical Service Bulletin # 02-07-30-052C Date: 040901

A/T - Fluid Flushing Procedure/Tool


This TSB number 02-07-30-052C, dated 09/01/04 has been superceded by TSB number 02-07-30-052F , dated 09/09/09
Technical Service Bulletin # 04-07-30-037 Date: 040901

A/T - DEXRON III(R) (H-Revision) Specification Upgrade


This TSB number 04-07-30-037, dated 09/01/04 has been superceded by TSB number 04-07-30-037B , dated 06/12/06
Technical Service Bulletin # 04-07-30-037A Date: 050819

A/T - DEXRON VI Release/Applications


This TSB number 04-07-30-037A, dated 08/19/05 has been superceded by TSB number 04-07-30-037B , dated 06/12/06
Technical Service Bulletin # 05-03-10-003A Date: 051219

Tires/Wheels - Low Tire Pressure With Aluminum Wheels


This TSB number 05-03-10-003A, dated 12/19/05 has been superceded by TSB number 05-03-10-003F , dated 04/27/10
Technical Service Bulletin # 05-03-10-020 Date: 051222

Tires/Wheels - Nitrogen Gas Usage for Filling Tires


This TSB number 05-03-10-020, dated 12/22/05 has been superceded by TSB number 05-03-10-020C , dated 04/27/10
Technical Service Bulletin # 99-01-38-006 Date: 991201

A/C - Refrigerant Recovery & Recharge Equipment


This TSB number 99-01-38-006, dated 12/01/99 has been superceded by TSB number 99-01-38-006A , dated 05/01/00
Technical Service Bulletin # 01-01-38-006C Date: 040702

A/C - R-134A System Flushing Guidelines and Procedures


This TSB number 01-01-38-006C, dated 07/02/04 has been superceded by TSB number 01-01-38-006D , dated 09/01/04
Technical Service Bulletin # 05-03-07-009 Date: 050817

Alignment - Recommendations and Requirements


This TSB number 05-03-07-009, dated 08/17/05 has been superceded by TSB number 05-03-07-009B , dated 06/27/08
Technical Service Bulletin # 02-01-39-004A Date: 050822

A/C - PAG Oil Usage


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 212
Chevrolet Venture V6-3.4L VIN E 2537
This TSB number 02-01-39-004A, dated 08/22/05 has been superceded by TSB number 02-01-39-004B , dated 11/16/05
Technical Service Bulletin # 04-06-01-029A Date: 061128

Engine - Unnecessary Flushing Services


This TSB number 04-06-01-029A, dated 11/28/06 has been superceded by TSB number 04-06-01-029E , dated 04/29/10
Technical Service Bulletin # 00-03-10-002D Date: 060801

Wheels Chrome Wheel Chemical Staining/Pitting/Corrosion


This TSB number 00-03-10-002D, dated 08/01/06 has been superceded by TSB number 00-03-10-002E , dated 03/15/10
Technical Service Bulletin # 06-03-10-010 Date: 060907

Wheels - Changing Procedures/Precautions


This TSB number 06-03-10-010, dated 09/07/06 has been superceded by TSB number 06-03-10-010A , dated 06/09/10
Technical Service Bulletin # 04-03-10-012A Date: 060922

Wheels - Pitting/Brake Dust On Chrome Wheels


This TSB number 04-03-10-012A, dated 09/22/06 has been superceded by TSB number 04-03-10-012B , dated 02/01/08
Technical Service Bulletin # 03-03-10-007B Date: 060817

Tires - Original Equipment Tire Characteristics


This TSB number 03-03-10-007B, dated 08/17/06 has been superceded by TSB number 03-03-10-007E , dated 08/05/09
Technical Service Bulletin # 00-00-90-002D Date: 060822

Tires - Inflation Pressure Information


This TSB number 00-00-90-002D, dated 08/22/06 has been superceded by TSB number 00-00-90-002J , dated 01/28/09
Technical Service Bulletin # 04-03-10-001C Date: 061002

Tires - Tread Puncture Repair Procedures


This TSB number 04-03-10-001C, dated 10/02/06 has been superceded by TSB number 04-03-10-001F , dated 04/27/10
Technical Service Bulletin # 00-03-10-006B Date: 070110

Tires - Radial Force Variation (RFV) Information


This TSB number 00-03-10-006B, dated 01/10/07 has been superceded by TSB number 00-03-10-006F , dated 05/04/10
Technical Service Bulletin # 01-06-01-011C Date: 061213

Engine - Engine Oil Consumption Guideline Information


This TSB number 01-06-01-011C, dated 12/13/06 has been superceded by TSB number 01-06-01-011E , dated 12/18/08
Technical Service Bulletin # 05-06-02-002A Date: 060831

Cooling System - DEXCOOL(R) Leak Detection Dye


This TSB number 05-06-02-002A, dated 08/31/06 has been superceded by TSB number 05-06-02-002B , dated 01/18/08
Technical Service Bulletin # 05-03-07-009A Date: 060928

Wheel Alignment - Recommendations/Requirements


This TSB number 05-03-07-009A, dated 09/28/06 has been superceded by TSB number 05-03-07-009B , dated 06/27/08
Technical Service Bulletin # 00-00-90-002E Date: 070226

Tires - Proper Tire Pressure Information


This TSB number 00-00-90-002E, dated 02/26/07 has been superceded by TSB number 00-00-90-002J , dated 01/28/09
Technical Service Bulletin # 00-00-90-002F Date: 070424

Tires - Proper Inflation Pressure Information


This TSB number 00-00-90-002F, dated 04/24/07 has been superceded by TSB number 00-00-90-002J , dated 01/28/09
Technical Service Bulletin # 04-07-30-037C Date: 070411

A/T - DEXRON-VI(R) Fluid Availability


This TSB number 04-07-30-037C, dated 04/11/07 has been superceded by TSB number 04-07-30-037D , dated 11/21/07
Technical Service Bulletin # 05-03-10-005B Date: 070207

Wheels/Tires - 'Upsized' Wheel & Tire Information


This TSB number 05-03-10-005B, dated 02/07/07 has been superceded by TSB number 05-03-10-005D , dated 09/11/08
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 213
Chevrolet Venture V6-3.4L VIN E 2538
Technical Service Bulletin # 00-00-90-002G Date: 070518

Tires - Proper Inflation Pressure Info.


This TSB number 00-00-90-002G, dated 05/18/07 has been superceded by TSB number 00-00-90-002J , dated 01/28/09
Technical Service Bulletin # 07-06-01-016 Date: 070814

Engine - Noise Damage Caused By The Oil Filter


This TSB number 07-06-01-016, dated 08/14/07 has been superceded by TSB number 07-06-01-016B , dated 07/27/09
Technical Service Bulletin # 07-06-01-016A Date: 070917

Engine - Internal Noise/Damage After Oil Filter Change


This TSB number 07-06-01-016A, dated 09/17/07 has been superceded by TSB number 07-06-01-016B , dated 07/27/09
Technical Service Bulletin # 00-00-90-002H Date: 070926

Tires - Information on Proper Tire Pressure


This TSB number 00-00-90-002H, dated 09/26/07 has been superceded by TSB number 00-00-90-002J , dated 01/28/09
Technical Service Bulletin # 03-08-48-006C Date: 071009

A/C - Rear Window Defroster Contact or Tab Repair


This TSB number 03-08-48-006C, dated 10/09/07 has been superceded by TSB number 03-08-48-006G , dated 02/26/10
Technical Service Bulletin # 05-03-10-005C Date: 070821

Wheel/Tire - Upsized Wheel/Tire Performance Info.


This TSB number 05-03-10-005C, dated 08/21/07 has been superceded by TSB number 05-03-10-005D , dated 09/11/08
Technical Service Bulletin # 03-03-10-007C Date: 070921

Tires/Wheels - Vibration/Balance/Shake/Flat Spotting


This TSB number 03-03-10-007C, dated 09/21/07 has been superceded by TSB number 03-03-10-007E , dated 08/05/09
Technical Service Bulletin # 00-00-90-002I Date: 071023

Tires/Wheels - Tire Inflation Pressure Information


This TSB number 00-00-90-002I, dated 10/23/07 has been superceded by TSB number 00-00-90-002J , dated 01/28/09
Technical Service Bulletin # 00-03-10-006C Date: 080109

Tires - (RFV) Radial Force Variation Information


This TSB number 00-03-10-006C, dated 01/09/08 has been superceded by TSB number 00-03-10-006F , dated 05/04/10
Technical Service Bulletin # 04-03-10-001D Date: 080107

Tires - Tire Puncture Repair Procedures


This TSB number 04-03-10-001D, dated 01/07/08 has been superceded by TSB number 04-03-10-001F , dated 04/27/10
Technical Service Bulletin # 05-03-10-020A Date: 080103

Tires - Nitrogen Gas Usage


This TSB number 05-03-10-020A, dated 01/03/08 has been superceded by TSB number 05-03-10-020C , dated 04/27/10
Technical Service Bulletin # 07-03-10-016 Date: 071217

Wheels/Tires - Changing Tire and Wheel Assemblies


Bulletin No.: 07-03-10-016

Date: December 17, 2007

INFORMATION

Subject:
GM Guidelines for Changing Tire and Wheel Assemblies

Models:
2008 and Prior GM Passenger Cars and Light Duty Trucks (including Saturn)
2008 and Prior HUMMER H2, H3

The purpose of this bulletin is to provide additional information and guidance when changing out tire and wheel assemblies on any General Motors
vehicle. Given the market demand to personalize vehicles with different tire and wheel assemblies, it is important to remind dealers of the vehicle
implications and requirements that are the responsibility of your dealership.
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 214
Chevrolet Venture V6-3.4L VIN E 2539

The National Traffic and Canadian Motor Vehicle Safety Act (Safety Act) provides, in part, a dealer may not sell vehicles or equipment that do not
comply with the applicable safety standards. Dealers are prohibited from making inoperative, in whole or in part, any part of a device or element of
design installed on or in a motor vehicle in compliance with an applicable motor vehicle safety standard. Accordingly, a dealer must replace the
vehicle tire and loading placard if, after the dealer installs GM Accessory Wheels and Tires, the information required is no longer accurate.

As a reminder, GM Accessory Wheel and Tire Assemblies are released in approved tire and wheel combinations that have been designed and
validated by GM Engineering for a specific vehicle application. Each GM Accessory wheel contains the appropriate installation instructions which
may include, but not limited to, change to the TPMS (Tire Pressure Monitoring System), updating the ABS Module to reflect correct tire size,
vehicle calibration and updating the tire size information using the Tire Placard insert (as shown in the example).

FMVSS and CMVSS 110, Tire Selection and Rims, requires the "Tire Placard Label Insert" (refer to graphic-English shown - French and Spanish
included for accessory wheels) to be affixed to each vehicle.

Do not use the information offered in the ABS module (tire size selection) as a guide to determine what tires are applicable to the vehicle in
question. Changing the tire size in the ABS module will only affect ABS wheel speed sensor calibrations that are direct inputs to the ABS module.
It will not correct or calibrate the speedometer's accuracy or other sensor values. To verify if GM Accessories offers optional tire and wheel
combinations for a specific vehicle configuration, refer to GM Dealer World - "Accessory Information Center". In Canada, refer to GMinfoNET -
"Product Information - Accessories" located under Parts & Accessories page.

Installation of Non-GM Products:

Before non-GM products are installed on new vehicles, dealers should refer to Article 5.1.1 of the GM Dealer Sales and Service Agreement
("Dealer Agreement"). If a dealer modifies or sells a modified new vehicle, or installs any equipment, accessory, recycled part or part not supplied
by General Motors, the dealer must disclose this fact on the purchase order and bill of sales, indicating that the modification, equipment, accessory
or part is not warranted by General Motors. Refer to form "Dealer Disclosure of Non-GM Products Used" in section 3.3 (3.2.1 in Canada) of the
GM Service Policy and Procedures Manual.

Vehicle Repairs:

Refer to Article 7.2 of the Dealer Agreement - The dealer agreement provides that dealers will only use genuine GM or GM approved Parts and
Accessories in performing warranty repairs, special policy repairs and any other repairs paid for by General Motors. This also is addressed in
Article 1.2.4e of the GM Service Policy and Procedures Manual.

DisclaimerTechnical Service Bulletin # 05-03-10-003C Date: 080115

Wheels/Tires -Low Tire Pressure


This TSB number 05-03-10-003C, dated 01/15/08 has been superceded by TSB number 05-03-10-003F , dated 04/27/10
Technical Service Bulletin # 08-06-01-008 Date: 080327

Engine - Accessory Drive Belt Noise Diagnostics/Tool


This TSB number 08-06-01-008, dated 03/27/08 has been superceded by TSB number 08-06-01-008A , dated 07/27/09
Technical Service Bulletin # 08-03-10-004 Date: 080325

Wheels/Tires - Accessory Wheel/Tire Mounting/Balancing


This TSB number 08-03-10-004, dated 03/25/08 has been superceded by TSB number 08-03-10-004A , dated 07/24/09
Technical Service Bulletin # 08-03-10-005 Date: 080501

Wheels/Tires - Chrome or Chrome Plated Steel Valve Caps


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 215
Chevrolet Venture V6-3.4L VIN E 2540
This TSB number 08-03-10-005, dated 05/01/08 has been superceded by TSB number 08-03-10-005A , dated 03/31/09
Technical Service Bulletin # 08-03-10-006 Date: 080501

Wheels/Tires - Tire Slowly Loses Air/Low Tire Message


This TSB number 08-03-10-006, dated 05/01/08 has been superceded by TSB number 08-03-10-006C , dated 04/27/10
Technical Service Bulletin # 00-03-10-006D Date: 081126

Tires - Radial Force Variation (RFV) Info.


This TSB number 00-03-10-006D, dated 11/26/08 has been superceded by TSB number 00-03-10-006F , dated 05/04/10
Technical Service Bulletin # 05-03-10-020B Date: 090122

Tire - Use Of Nitrogen Gas In Tires


This TSB number 05-03-10-020B, dated 01/22/09 has been superceded by TSB number 05-03-10-020C , dated 04/27/10
Technical Service Bulletin # 03-03-10-007D Date: 081124

Wheels/Tires - Original Equipment Characteristics


This TSB number 03-03-10-007D, dated 11/24/08 has been superceded by TSB number 03-03-10-007E , dated 08/05/09
Technical Service Bulletin # 04-03-10-001E Date: 090326

Wheels/Tires - Tire Puncture Repair Procedures


This TSB number 04-03-10-001E, dated 03/26/09 has been superceded by TSB number 04-03-10-001F , dated 04/27/10
Technical Service Bulletin # 05-03-10-003D Date: 090511

Wheels/Tires - Low Tire Pressure


This TSB number 05-03-10-003D, dated 05/11/09 has been superceded by TSB number 05-03-10-003F , dated 04/27/10
Technical Service Bulletin # 05-03-10-003E Date: 091204

Wheels/Tires - Low Tire Pressure/Aluminum Wheels Leak


This TSB number 05-03-10-003E, dated 12/04/09 has been superceded by TSB number 05-03-10-003F , dated 04/27/10
Technical Service Bulletin # 08-03-10-006B Date: 091204

Wheels/Tires - Tire(s) Slowly Go Flat


This TSB number 08-03-10-006B, dated 12/04/09 has been superceded by TSB number 08-03-10-006C , dated 04/27/10
Technical Service Bulletin # 00-03-10-006E Date: 091104

Tires - Tire Radial Force Variation (RFV)


This TSB number 00-03-10-006E, dated 11/04/09 has been superceded by TSB number 00-03-10-006F , dated 05/04/10
Technical Service Bulletin # 08-03-10-006A Date: 091105

Wheels/Tires - Tire Slowly Goes Flat/Tire Air Loss


This TSB number 08-03-10-006A, dated 11/05/09 has been superceded by TSB number 08-03-10-006C , dated 04/27/10
Technical Service Bulletin # 00-00-89-008D Date: 040408

Vehicle - Recreational Dinghy Towing


This TSB number 00-00-89-008D, dated 04/08/04 has been superceded by TSB number 00-00-89-008F , dated 07/28/06
Technical Service Bulletin # 00-00-89-008C Date: 031101

Vehicle - 'Dinghy' Towing


This TSB number 00-00-89-008C, dated 11/01/03 has been superceded by TSB number 00-00-89-008F , dated 07/28/06
Technical Service Bulletin # 00-00-89-008 Date: 000401

Recreational Vehicle - (Dinghy) Towing


This TSB number 00-00-89-008, dated 04/01/00 has been superceded by TSB number 00-00-89-008F , dated 07/28/06
Technical Service Bulletin # 03-06-04-030A Date: 040624

Fuel System - Possible MIL ON/Driveability Issues


Bulletin No.: 03-06-04-030A

Date: June 24, 2004

TECHNICAL
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 216
Chevrolet Venture V6-3.4L VIN E 2541

Subject:
Multiple Driveability Symptoms Due to Clogged Fuel Injectors (Clean Injectors)

Models

Supercede:

This bulletin is being revised to update the procedure, models and model years. Please discard Corporate Bulletin Number 03-06-04-030 (Section
06 - Engine).

Condition

Some owners may comment on driveability symptoms of long or hard starts, chuggle, rough idle and light or intermittent misfire. The malfunction
indicator lamp (MIL) may also illuminate.

Cause

Due to various factors, the fuel injectors may become restricted. Extensive testing has demonstrated that fuel related issues are the cause of clogged
injectors. At this point, no specific fuel, fuel constituent, or engine condition has been identified as causing the restriction. The restriction causes the
engine to operate at a lean air fuel ratio. This may either trigger the MIL to illuminate or the engine to develop various driveability symptoms.

Correction
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 217
Chevrolet Venture V6-3.4L VIN E 2542

Fuel injector restrictions, deposits, can be cleaned on the vehicle using the following procedure. Under NO circumstances should this procedure be
modified, changed or shortened.

Note:
The recommended mixture amount of GM Top-Engine Cleaner has been increased from 5% used in prior procedures to 10%. This increase was
implemented to improve the effectiveness of the injector cleaning procedure. Follow the cleaning procedure carefully to minimize the risk of
fuel system damage. Testing has demonstrated that exceeding the 10% cleaning solution concentration does not improve the effectiveness of
this procedure. GM Top-Engine Cleaner is the only injector cleaning agent approved for use with General Motors fuel system components.
Other injector cleaners may cause damage to plastics, plated metals or bearings. General Motors has completed extensive laboratory testing of
GM Top-Engine Cleaner, and can assure its compatibility with General Motors fuel system components, as long as the cleaning procedure is
followed correctly.

Important:
This bulletin recommends the use of pre-measured containers of GM Top-Engine Cleaner, P/N 12346535, - U.S. USAGE ONLY. Pre-measured
containers eliminate the need to measure the amount of GM Top-Engine Cleaner being added to the J 35800-A, injector cleaning tool. In
Canada, use P/N 992872. It will be necessary to measure and dispense Top Engine Cleaner into the J 35800-A, injector cleaning tool.

Injector Balance Test

The following tools, or their equivalent, are required:

^ J 35800-A Fuel Injector Cleaner


^ J 37287 Fuel Line Shut-off Adapter
^ J 42964 Fuel Line Shut-off Adapter
^ J 42873 Fuel Line Shut-off Adapter
^ Four pre-measured GM Top-Engine Cleaner Containers, 24 ml (0.812 oz) each, P/N 12346535, U.S. USAGE ONLY. In Canada, use P/N
992872, 443.6 ml (15 oz) bottle. It will be necessary to measure and dispense 48 ml (1.6 oz) of Top Engine-Cleaner into the J 35800-A, injector
cleaning tool twice during this procedure. See Injector Cleaning Procedure below for further information.

Important:
Analysis of returned Multec II injectors indicate that terminal fretting corrosion may also be responsible for the conditions described in this
bulletin. Since fretting corrosion (microscopic in nature) is nearly impossible to detect in the field, the following steps should be taken to ensure
that fretting corrosion is not an issue before performing any additional diagnostics.

Fretting is a term used to describe a tiny rubbing motion that occurs between two surfaces. Fretting corrosion refers to a build up of insulating,
oxidized debris that forms on electrical connections due to a fretting action at the contact points. Injector vibration, engine vibration, and electrical
harness movement are contributors to the fretting motion.

Depending on how large the build-up of oxide is will determine how drastic the effect will be on the injector circuit. Worst case is a total loss of
continuity in the connection resulting in P0200 (Injector Circuit Fault) and P0300 (Misfire) codes being set. If the oxides create a high resistance
circuit, insufficient current will be available to properly open the injector, resulting in unstable fuel delivery and ultimately a P0300 DTC. High
resistance in the circuit will not necessarily set a DTC P0200. Keep in mind that a connection with fretting corrosion is unstable. Since movement
causes fretting, any vibration may create a condition where the connection varies from an open circuit, to a high resistance connection, to a good
connection.

Important:
Unless intermittent mis-fire due to fretting corrosion is suspected when servicing 3.1 L and 3.4L engines, skip steps 1 through 4. Steps 1
through 4 may be performed at a future date when the upper intake is removed.

When servicing 2.8L, 3.5L or 4.2L engines (VINs 8, 6, S - RPOs LK5, L52, LL8) skip steps 1 through 4 unless replacing injectors.

1. Disconnect one injector electrical connector.

2. Apply a small amount, about the size of a BB, of dielectric grease, P/N 12377900 (in Canada, P/N 10953529) to the female terminal. Be sure
to cover both cavities.

3. Reconnect electrical connector to injector.

4. Repeat steps 1 through 3 for all remaining injectors.

5. Using the Tech 2(R), perform an injector balance test using the procedure in the appropriate Service Manual. Use the Tech 2(R) to select
each individual injector. Record the pressure drop of each injector on the repair order.
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 218
Chevrolet Venture V6-3.4L VIN E 2543

Important:
Technicians must record the results of all injector balance tests and keep them with the repair order. For your convenience, the bulletin
has a worksheet shown for recording the test results.
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 219
Chevrolet Venture V6-3.4L VIN E 2544

6. Subtract the lowest pressure drop, leanest injector, from the highest pressure drop, richest injector. If there is greater than or equal to a 20 kPa
difference between the lowest and highest pressure drop, then the fuel injectors may be the cause of the driveability symptom. See the
example tables shown to determine if cleaning is appropriate.

7. If there is less than a 20 kPa difference, between the highest and lowest fuel pressure drop, the fuel injectors are operating properly and
further Service Manual diagnostics should be performed on the vehicle. All diagnostic time should be added to the appropriate labor
operation for the repair performed and not to injector cleaning.

Although the pressure drop is greater than or equal to 20 kPa, cylinder 2 stands out as being rich when compared to the other injectors. Do
not clean the injectors. Replace injector number 2. Charge time to labor operation J5650.

Important:
When replacing injectors be sure to add dielectric grease to injector electrical connectors.

The pressure drop is greater than or equal to 20 kPa. Injectors 1 and 3 appear to be lean when compared to injectors 2, 4, 5 and 6. Clean and
re-test pressure drop. If cleaning does not restore flow on injectors 1 or 3, replace the detective injector or injectors as necessary. Charge time
to labor operation J5650.

Injector Cleaning Procedure

Note:
GM Top-Engine Cleaner is the only injector cleaning agent recommended. DO NOT USE OTHER CLEANING AGENTS, AS THEY
MAY CONTAIN METHANOL WHICH CAN DAMAGE FUEL SYSTEM COMPONENTS. Under NO circumstances should the GM
Top-Engine Cleaner be added to the vehicle fuel tank, as it may damage the fuel pump and other system components.

Do not exceed a 10% cleaning solution concentration. Higher concentrations may damage fuel system components. Testing has demonstrated
that exceeding the 10% cleaning solution concentration does not improve the effectiveness of this procedure.

During this procedure, you will need a total of 960 ml (32.4 oz) of cleaning solution (10% Top Engine Cleaner/90% Regular Unleaded
Gasoline). That is two tanks of solution for the J 35800-A Fuel Injector Cleaner Tank. Other brands of tools may have a different capacity
and would, therefore, require more or less tanks to complete the procedure. You must use all 960 ml (32.4 oz) of solution (10% Top Engine
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 220
Chevrolet Venture V6-3.4L VIN E 2545
Cleaner/90% Regular Unleaded Gasoline) to insure complete injector cleaning.

Important:
Vehicles with less than 100 miles (160 km) on the odometer should not have the injectors cleaned. These vehicles should have any out of
specification injectors replaced.

1. For U.S. dealers, empty 2 pre-measured GM Top-Engine Cleaner containers, 24 ml (0.812 oz) each, P/N 12346535, into the J 35800-A,
injector cleaning tank. For Canadian Dealers, measure and dispense 48 ml (1.62 oz) of Top-Engine Cleaner, P/N 992872, into the J 35800-A,
injector cleaning tank. If you are using any other brand of tank, you will need a total of 96 ml (3.24 oz) of Top-Engine Cleaner mixed with
864 ml (29.16 oz) of regular unleaded gasoline.

2. Fill the injector cleaning tank with regular unleaded gasoline. Be sure to follow all additional instructions provided with the tool.

3. Electrically disable the vehicle fuel pump by removing the fuel pump relay and disconnecting the oil pressure switch connector, if equipped.

4. Turn the ignition to the Off position.

5. Relieve fuel pressure and disconnect the fuel feed and return lines at the fuel rail. Plug the fuel feed and return lines coming off the fuel rail
with J 37287, J 42873 or J 42964 as appropriate for the fuel system.

6. Connect the J 35800-A to the vehicle fuel rail.

7. Pressurize the J 35800-A to 510 kPa (75 psi).

8. Start and idle the engine until it stalls, due to lack of fuel. This should take approximately 15-20 minutes.

9. Turn the ignition to the Off position.

10. Refill the J 35800-A injector cleaning tank per steps 1 and 2.

11. Start and idle the engine until it stalls, due to lack of fuel. This should take approximately 15-20 minutes.

12. Turn the ignition to the Off position.

13. Disconnect J 35800-A from the fuel rail.

14. Reconnect the vehicle fuel pump relay and oil pressure switch connector, if equipped.

15. Remove the J 37287, J 42873 or J 42964 and reconnect the vehicle fuel feed and return lines.

16. Start and idle the vehicle for an additional 2 minutes to ensure residual injector cleaner is flushed from the fuel rail and fuel lines.

17. Repeat Step 5 of the Injector Balance Test and record the fuel pressure drop from each injector.

18. Subtract the lowest fuel pressure drop from the highest fuel pressure drop. If the value is less than 15 kPa, no additional action is required. If
the value is greater than or equal to 15 kPa, replace the injector assembly with the lowest fuel pressure drop. Follow injector replacement
procedures outlined in the appropriate Service Manual Information for the vehicle. Repeat balance test to ensure that all injectors fall within
15 kPa.

19. Add one ounce (30 ml) of Fuel System Treatment, P/N 12345104 (Canada P/N 89020804), to the vehicle fuel tank for each gallon (3.78 L) of
gasoline estimated to be in the fuel tank. Instruct the customer to add the remainder of the bottle of Fuel System Treatment to the vehicle fuel
tank at the next fill-up.

20. Advise customer to change brands of fuel and to add GM Fuel System Treatment at every oil change. Regular use of GM Fuel System
Treatment should keep the customer from having to repeat the injector cleaning procedure.

21. Road test the vehicle to verify that the customer concern has been corrected.
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 221
Chevrolet Venture V6-3.4L VIN E 2546

Parts Information

Parts are currently available from GMSPO.

Warranty Information

For vehicles serviced under warranty, use the table.

Disclaimer
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 222
Chevrolet Venture V6-3.4L VIN E 2547

Technical Service Bulletin # 02-06-05-004 Date: 020926

Emissions - Catalytic Converter Damage/Misfire DTC's


This TSB number 02-06-05-004, dated 09/26/02 has been superceded by TSB number 02-06-05-004B , dated 02/14/06
Technical Service Bulletin # 03-06-04-030 Date: 030528

Fuel System - Possible MIL ON/Driveability Symptoms


Bulletin No.: 03-06-04-030

Date: May 28, 2003

TECHNICAL

Subject:
Multiple Driveability Symptoms Due to Clogged Fuel Injectors (Clean Injectors)

Models:
2000-2003 Buick Century, LeSabre, Park Avenue, Regal
2002-2003 Buick Rendezvous
2002-2003 Cadillac Escalade, Escalade EXT
2003 Cadillac Escalade ESV
2000 Chevrolet S-10
2000-2002 Chevrolet Camaro, Lumina
2000-2003 Chevrolet Cavalier, Impala, Malibu, Monte Carlo, Silverado, Suburban, Tahoe, Venture
2001-2003 Chevrolet Express
2002-2003 Chevrolet Astro, Avalanche, Trailblazer
2003 Chevrolet Blazer, S-10, Trailblazer EXT
2000 GMC Sonoma
2000-2003 GMC Sierra, Yukon, Yukon XL
2001-2003 GMC Denali, Denali XL Savana
2002-2003 GMC Envoy, Safari
2003 GMC Envoy XL, Jimmy, Sonoma
2000-2003 Oldsmobile Alero, Silhouette
2002-2003 Oldsmobile Bravada
2000-2001 Pontiac Transport
2000-2002 Pontiac Firebird
2000-2003 Pontiac Bonneville, Grand Am, Grand Prix, Sunfire
2001-2003 Pontiac Aztek
2002-2003 Pontiac Montana
2003 HUMMER H2
with 2.2L, 3.1L, 3.4L, 3.8L, 4.2L, 4.3L, 4.8L, 5.3L, 6.0L, or 8.1L Engine (VINs F, 4, J, E, K, S, X, V, T, N, U, G - RPOs L61, LN2, LG8, LA1,
L36, LL8, LU3, LR4, LM7, LQ9, LQ4, L18)
and Multec II Fuel Injectors Condition

Some owners may comment on driveability symptoms of long or hard starts, chuggle, rough idle and light or intermittent misfire. The malfunction
indicator lamp (MIL) may also illuminate.

Cause

Due to various factors, the fuel injectors may become restricted. Extensive testing has demonstrated that fuel related issues are the cause of clogged
injectors. At this point, no specific fuel, fuel constituent, or engine condition has been identified as causing the restriction. The restriction causes the
engine to operate at a lean air fuel ratio. This may either trigger the MIL to illuminate or the engine to develop various driveability symptoms.
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 223
Chevrolet Venture V6-3.4L VIN E 2548

Parts Information

Parts are currently available from GMSPO.

Warranty Information

For vehicles serviced under warranty, use the table.

Disclaimer
Correction
Fuel injector restrictions, deposits, can be cleaned on the vehicle using the following procedure. Under NO circumstances should this procedure be
modified, changed or shortened.

Notice:
The recommended mixture amount of GM Top-Engine Cleaner has been increased from 5% used in prior procedures to 10%. This increase was
implemented to improve the effectiveness of the injector cleaning procedure. Follow the cleaning procedure carefully to minimize the risk of
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 224
Chevrolet Venture V6-3.4L VIN E 2549
fuel system damage. Testing has demonstrated that exceeding the 10% cleaning solution concentration does not improve the effectiveness of
this procedure. GM Top-Engine Cleaner is the only injector cleaning agent approved for use with General Motors fuel system components.
Other injector cleaners, while effective, may cause damage to plastics, plated metals or bearings. General Motors has completed extensive
laboratory testing of GM Top-Engine Cleaner, and can assure its compatibility with General Motors fuel system components, as long as the
cleaning procedure is followed correctly.

Important:
This bulletin recommends the use of pre-measured containers of GM Top-Engine Cleaner, P/N 12346535, - U.S. USAGE ONLY. Pre-measured
containers eliminate the need to measure the amount of GM Top-Engine Cleaner being added to the J 35800-A, injector cleaning tool. In
Canada, use P/N 992872. It will be necessary to measure and dispense Top Engine Cleaner into the J 35800-A, injector cleaning tool.

Injector Balance Test

The following tools, or their equivalent, are required:

^ J 35800-A Fuel Injector Cleaner

^ J 37287 Fuel Line Shut-off Adapter

^ J 42964 Fuel Line Shut-off Adapter

^ J 42873 Fuel Line Shut-off Adapter

^ Four pre-measured GM Top-Engine Cleaner Containers, 24 ml (0.812 oz) each, P/N 12346535, U.S. USAGE ONLY. In Canada, use P/N
992872, 443.6 ml (15 oz) bottle. It will be necessary to measure and dispense 48 ml (1.6 oz) of Top Engine-Cleaner into the J 35800-A, injector
cleaning tool twice during this procedure. See Injector Cleaning Procedure below for further information.

Important:
Analysis of returned Multec II injectors indicate that terminal fretting corrosion may also be responsible for the conditions described in this
bulletin. Since fretting corrosion (microscopic in nature) is nearly impossible to detect in the field, the following steps should be taken to ensure
that fretting corrosion is not an issue before performing any additional diagnostics. Fretting is a term used to describe a tiny rubbing motion that
occurs between two surfaces. Fretting corrosion refers to a build up of insulating, oxidized debris that forms on electrical connections due to a
fretting action at the contact points. Injector vibration, engine vibration, and electrical harness movement are contributors to the fretting motion.

Depending on how large the build-up of oxide is will determine how drastic the effect will be on the injector circuit. Worst case is a total loss of
continuity in the connection resulting in P0200 (Injector Circuit Fault) and P0300 (Misfire) codes being set. If the oxides create a high
resistance circuit, insufficient current will be available to properly open the injector, resulting in unstable fuel delivery and ultimately a P0300
DTC. High resistance in the circuit will not necessarily set a DTC P0200. Keep in mind that a connection with fretting corrosion is unstable.
Since movement causes fretting, any vibration may create a condition where the connection varies from an open circuit, to a high resistance
connection, to a good connection.

Important:
Unless intermittent mis-fire due to fretting corrosion is suspected when servicing 3.1L and 3.4L engines, skip steps 1 through 4. Steps 1 through
4 may be performed at a future date when the upper intake is removed.

1. Disconnect one injector electrical connector.

2. Apply a small amount, about the size of a BB, of dielectric grease, P/N 12377900 (in Canada, P/N 10953529) to the female terminal. Be sure
to cover both cavities.

3. Reconnect electrical connector to injector.

4. Repeat steps 1 through 4 for all remaining injectors.

5. Using the Tech 2(R), perform an injector balance test. Use the Tech 2(R) to select each individual injector. Record the pressure drop of each
injector on the repair order.

Important:
It is mandatory that the dealer record the results of the Injector Balance Test on the repair order.

6. Subtract the lowest pressure drop, leanest injector, from the highest pressure drop, richest injector. If there is more than a 20 kPa (3 psi)
difference between the lowest and highest pressure drop, then the fuel injectors may be the cause of the driveability symptom. See the
example tables below to determine if cleaning is appropriate.

7. If there is a 20 kPa (3 psi) difference, or less, between the highest and lowest fuel pressure drop, the fuel injectors are operating properly and
further diagnostics should be performed on the vehicle.
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 225
Chevrolet Venture V6-3.4L VIN E 2550

Maximum Difference: 68-41 = 27 kPa (10-6 = 4 psi)

Although the pressure drop is greater than 20 kPa (3 psi), cylinder 2 stands out as being rich when compared to the other injectors. Do not
clean the injectors. Replace injector number 2. Charge time to labor operation J5650.

Maximum Difference: 48-23 = 25 kPa (7-3 = 4 psi)

The pressure drop is greater than 20 kPa (3 psi). Injectors 1 and 3 appear to be lean when compared to injectors 2, 4, 5 and 6. Clean and
re-test pressure drop. If cleaning does not restore flow on injectors 1 or 3, replace the defective injector or injectors as necessary. Charge time
to labor operation J5650.

Injector Cleaning Procedure

Notice:
GM Top-Engine Cleaner is the only injector cleaning agent recommended. DO NOT USE OTHER CLEANING AGENTS, AS THEY
MAY CONTAIN METHANOL WHICH CAN DAMAGE FUEL SYSTEM COMPONENTS. Under NO circumstances should the GM
Top-Engine Cleaner be added to the vehicle fuel tank, as it may damage the fuel pump and other system components.

Do not exceed a 10% cleaning solution concentration. Higher concentrations may damage fuel system components. Testing has
demonstrated that exceeding the 10% cleaning solution concentration does not improve the effectiveness of this procedure.

During this procedure, you will need a total of 960 ml (32.4 oz) of cleaning solution (10% Top Engine Cleaner/90% Regular Unleaded
Gasoline). That is two tanks of solution for the J 35800-A Fuel Injector Cleaner Tank. Other brands of tools may have a different capacity
and would, therefore, require more or less tanks to complete the procedure. You must use all 960 ml (32.4 oz) of solution (10% Top
Engine Cleaned/90% Regular Unleaded Gasoline) to insure complete injector cleaning.

1. For U.S. dealers, empty 2 pre-measured GM Top-Engine Cleaner containers, 24 ml (0.812 oz) each, P/N 12346535, into the J 35800-A,
injector cleaning tank. For Canadian Dealers, measure and dispense 48 ml (1.62 oz) of Top-Engine Cleaner, P/N 992872, into the J 35800-A,
injector cleaning tank. If you are using any other brand of tank, you will need a total of 96 ml (3.24 oz) of Top-Engine Cleaner mixed with
864 ml (29.16 oz) of regular unleaded gasoline.

2. Fill the injector cleaning tank with regular unleaded gasoline. Be sure to follow all additional instructions provided with the tool.

3. Electrically disable the vehicle fuel pump by removing the fuel pump relay and disconnecting the oil pressure switch connector, if equipped.
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 226
Chevrolet Venture V6-3.4L VIN E 2551

4. Relieve fuel pressure and disconnect the fuel feed and return lines at the fuel rail. Plug the fuel feed and return lines coming off the fuel rail
with J 37287, J 42874 or J 42964 as appropriate for the fuel system.

5. Connect the J 35800-A to the vehicle fuel rail.

6. Pressurize the J 35800-A to 510 kPa (75 psi).

7. Start and idle the engine until it stalls, due to lack of fuel. This should take approximately 15-20 minutes.

8. Refill the J 35800-A injector cleaning tank per steps 2 and 3.

9. Start and idle the engine until it stalls, due to lack of fuel. This should take approximately 15-20 minutes.

10. Disconnect J 35800-A from the fuel rail.

11. Reconnect the vehicle fuel pump relay and oil pressure switch connector, if equipped.

12. Remove the J 37287, J 42874 or J 42964 and reconnect the vehicle fuel feed and return lines.

13. Start and idle the vehicle for an additional 2 minutes to ensure residual injector cleaner is flushed from the fuel rail and fuel lines.

14. Repeat Steps 1-5 of the Injector Balance Test and record the fuel pressure drop from each injector.

15. Subtract the lowest fuel pressure drop from the highest fuel pressure drop. If the value is 15 kPa (2 psi) or less, no additional action is
required. If the value is greater than 15 kPa (2 psi), replace the injector assembly with the lowest fuel pressure drop. Follow injector
replacement procedures outlined in the appropriate Service Information Manual for the vehicle.

16. Add one ounce (30 ml) of Fuel System Treatment, P/N 12345104 (Canada P/N 10953467), to the vehicle fuel tank for each gallon (3.78 L) of
gasoline estimated to be in the fuel tank. Instruct the customer to add the remainder of the bottle of Fuel System Treatment to the vehicle fuel
tank at the next fill-up.

17. Advise customer to change brands of fuel and to add GM Fuel System Treatment every 3000 miles (4800 km). Regular use of GM Fuel
System Treatment should keep the customer from having to repeat the injector cleaning procedure.

18. Road test the vehicle to verify that the customer concern has been corrected.
Technical Service Bulletin # 04-07-30-013 Date: 040305

A/T - SES Lamp ON/Multiple Driveability Concerns


This TSB number 04-07-30-013, dated 03/05/04 has been superceded by TSB number 04-07-30-013B , dated 02/01/07
Technical Service Bulletin # 04-07-30-013A Date: 050125

A/T - Shift/Driveability Concerns/SES Lamp ON


This TSB number 04-07-30-013A, dated 01/25/05 has been superceded by TSB number 04-07-30-013B , dated 02/01/07
Technical Service Bulletin # 00-08-64-015A Date: 010201

Power Sliding Side Door - Edge Guard Comes Loose


File In Section: 08 - Body and Accessories

Bulletin No.: 00-08-64-015A

Date: February 2001

TECHNICAL

Subject:
Power Sliding Side Door Edge Guard Comes Loose
(Install New Edge Guard)

Models:
1997-2000 Chevrolet Venture
1997-2000 Oldsmobile Silhouette
1997-1999 Pontiac Trans Sport
1999-2000 Pontiac Montana

This bulletin is being revised to update parts information. Please discard Corporate Bulletin Number 00-08-64-015 (Section 08 - Body &
Accessories).
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 227
Chevrolet Venture V6-3.4L VIN E 2552

Condition

Some customers may comment that the door edge guard has started to come oft or the over-slam bumper has fallen off.

Cause

A loss of adhesion to the body may have occurred.

Correction

1. If the over-slam bumper is missing, clean the surface of the door and install the bumper just below the body feature line (see Figure).

2. Install the new door edge guard just below the over-slam bumper. The new door edge guard pushes over the hem flange on the front leading
edge of the door (see Figure).

Parts Information

Parts are currently available from GMSPO.

Warranty Information

For vehicles repaired under warranty, use the table.

DisclaimerTechnical Service Bulletin # 01-08-46-008D Date: 080115

01-08-46-008C BULLETIN CANCELLATION NOTICE


Bulletin No.: 01-08-46-008D

Date: January 15, 2008

INFORMATION

Subject:
Information on Upgrading Factory Installed OnStar(R) Generation 2.0 Equipped Vehicles to Generation 2.6

Models:
2000 Buick LeSabre Park Avenue
2000 Cadillac Catera DeVille Eldorado Seville
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 228
Chevrolet Venture V6-3.4L VIN E 2553
2000 Chevrolet Venture
2000 Oldsmobile Silhouette
2000 Pontiac Bonneville Montana
2001 Pontiac Aztek (Built Prior to VIN Breakpoint S525890)
2000 Chevrolet Blazer Suburban Tahoe
2000 GMC Envoy Yukon Yukon XL
2000 Oldsmobile Bravada

with Factory Installed OnStar(R)

Supercede:

This bulletin is being canceled. Please discard Corporate Bulletin Number 01-08-46-008C (Section 08 - Body and Accessories).

This bulletin is being issued to inform dealership service personnel that OnStar(R) is no longer making this program available to customers.

For vehicles that exhibit this condition technicians should refer to Corporate Bulletin Number 05-08-46-006N - Information on Upgrading Certain
OnStar(R) Analog/Digital-Ready Systems to OnStar(R) Generation 6 Digital-Capable System.

DisclaimerTechnical Service Bulletin # 06-00-89-054 Date: 061130

Warranty - Claims Submission


Bulletin No.: 06-00-89-054

Date: November 30, 2006

WARRANTY ADMINISTRATION

Subject:
Warranty Claims Submission - Importance of GM Part Numbers and Date Coded Parts

Models:
2007 and Prior GM Passenger Cars and Light Duty Trucks
2003-2007 HUMMER H2, H3
2005-2007 Saab 9-7X

GM Part Numbers

All parts used on GM vehicles are assigned a GM part number. Additionally, most of the parts used in the manufacturing of GM vehicles are
marked with GM part numbers directly on the part. This allows for easy verification of Genuine GM parts whether stocked at the warehouse,
installed on a vehicle, or being returned for warranty claims. Running changes are also sometimes necessary during a model year resulting in
additional part number changes mid-year.

Date Coded Parts and Identification Marks

Many of the parts used on powertrain, chassis, electrical and interior assemblies are marked and date coded in a variety of ways. You may find
stickers, bar codes, embossed clock faces, number stampings and riveted tags among many other methods on the parts you possess. While many of
these components are supplied to General Motors, almost all suppliers track these identifications as a method of quality assurance and containment
if ever an issue arises about a specific part.

Date Code Example


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 229
Chevrolet Venture V6-3.4L VIN E 2554

The sample picture is from a 2.4L 4 cylinder front engine cover. On this part, the date code appears as a "clock" wheel.

On the first day for each month of production, the casting dye is pulled. Using a center punch, an operator manually punches another point on the
date code wheel. To decode, you simply count the number of center punches, or impression, in the dial of the clock and you have the month.

The example picture has eight impressions, or center punch marks, on the wheel. The year is cast into the center of the dial or clock face. Therefore,
the example is identified as being from August 2006. This date along with the part number, and many different identifiers cast into the parts, are
used to track variations with multiple dies or production locations. When these marks are on the exterior surfaces when installed, they give GM
dealers a powerful advantage when used for inspection purposes.

When the above information is tied to the correct VIN of the vehicle, along with a complete and detailed repair order, it becomes an effective tool
to isolate parts with a given concern. This all depends on your dealership and care you take in regards to returned parts.

Warranty Claims Submittal and Accompanying Returned Parts Guidelines

It is vital that the exact part(s) replaced during a warranty repair be returned when requested. These parts must be the specific ones associated with
the repair order requested and must carry the proper date codes for the production run of the vehicle or component. Substitute parts are not
acceptable. This information is used during warranty part reviews and is tracked to determine possible problems with a specific production run. The
more precisely that GM can isolate a production time frame that is causing customer concerns, the quicker and more effectively we can target a
solution.

Warranty Debits

Parts that are returned out of date range for the specified vehicle on the repair order will first be cross-checked under the vehicle warranty system
for past replacements. If a past replacement is noted the warranty data will be recorded as such and the claim will be processed. Parts returned out
of date range for the vehicle repaired may be debited back to the dealer.

DisclaimerTechnical Service Bulletin # 99-00-89-019B Date: 020201

Warranty - Parts Return Program Explained


File In Section: 00 - General Information

Bulletin No.: 99-00-89-019B

Date: February, 2002

INFORMATION

Subject:
Warranty Parts Center/Corporate Parts Return Program

Models:
2003 and Prior Passenger Cars and Trucks
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 230
Chevrolet Venture V6-3.4L VIN E 2555
2003 HUMMER Model Vehicles
2003 and Prior Isuzu Medium Duty Trucks

Attention:
Parts Managers, Service Managers, Warranty Administrators

This bulletin is being revised to update changes to the Warranty Parts Center/Corporate Parts Return Program. Please discard Corporate Bulletin
Number 99-00-89-019A (Section 00 - General Information).

Important:
"GM of Canada" and "IPC" Dealers are not authorized to utilize this service bulletin. Canadian dealers should refer to "Home Office Letter #
99-201" dated 01-05-99 for all Warranty Parts Center returns.

This bulletin is effective October 1, 2001 and its purpose is to clarify instructions with regard to the Corporate Parts Return (CPR)
Program/Warranty Parts Center (WPC) in the areas of parts retention, parts preparation for shipping, and administration. This bulletin supersedes
all previous written communication regarding WPC operation.

CPR is considered a valuable tool for root cause analysis of customer product concerns. The GM Warranty Parts Center (WPC) has contracted with
United Parcel Service Logistics to transport and inventory all parts requested by CPR and returned from dealerships. The following information
will assist in returning parts to the WPC.

The WPC realizes that CPR requests are not always received by the appropriate dealership person on a timely basis; however, the program's
importance cannot be stressed often enough. It is highly recommended that an individual be assigned the responsibility of processing WPC requests
as quickly as possible.

DISCLAIMER
WPC Website
The WPC has implemented a website www.gmwpc.com to assist dealers in tracking their shipments to the WPC and to obtain copies of WPC
forms. The website is available 24 hours a day and is being updated constantly. In order to access the website, dealers will need their BAC
(Business Associate Code). The website has the following features:

^ Viewing the status of open requests.

^ Viewing details of a single request (including reason for debit).

^ Hotlink to UPS.com for tracking packages.

^ Hotlink to Yellowfreight.com for tracking shipments.

^ The most current parts return bulletin.

^ Templates of WPC forms.

- Parts Waiver

- Shipping Log

- Material Request

- Yellow Freight Bill of Lading

Upon entering the website, dealers will have the choice of selecting a list of all open WPC requests or selecting a specific request. Open requests
will be those which have not been received at the WPC as of the date queried. Single requests will give details of a particular request; namely-due
date and reason for debit (if applicable). Dealers should check WPC status of request prior to accessing UPS tracking.

Requests, Reminders and Debits


For examples of return requests and reminders, refer to examples shown in this bulletin.

Requests

When a part (and repair order copy) is needed, the dealership will receive a "GM Part and Repair Order Return Request" message. When a repair
order ONLY is needed, the dealership will receive an "R.O. Only Request" message. All CPR requests will be transmitted to dealer's electronic
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 231
Chevrolet Venture V6-3.4L VIN E 2556
mailbox within the "PARTRETURN CPR" report application on Tuesdays and Fridays of each week as warranty claims are paid. If there is no
actual part to return because a fluid, such as carburetor cleaner was used, the dealer must complete a Parts Waiver form stating "used carb cleaner"
and fax it to the WPC to avoid a debit (DO NOT MAIL) (248-371-9005).

Reminders

A reminder notice of previously requested parts/R.O.'s which have not been received by the WPC will also be provided on Tuesdays and Fridays.
These reminders will be listed in categories of "10-20 days old" and "at least 21 days old." Until parts are received, or the WPC has been contacted
for non-return of parts, or the parts have reached 28 days, these reminders will repeat with each claim cycle.

If the dealer has confirmed delivery to WPC with UPS, but reminder notices continue, the dealer is encouraged to check the WPC website
(www.gmwpc.com) for receipt confirmation.

It is imperative that the dealer follow-up with the WPC to RESOLVE open issues to avoid possible debit. Fax (248-371-9005) is recommended for
proof of follow-up with the WPC. If the original request is misplaced or unreadable, the reminder notice or website printout may be used for
shipping parts with their paperwork to the WPC.

For dealer information, the Request Number is nine-digits. As an example, 212613469 would be translated as follows:

^ The first position indicates the year of the request.


2 = 2002.

^ The next three positions indicate the Julian date. 126 = May.

^ The next four positions indicate the unique sequence number. In this example, it is 1346.

^ The last number is the check digit. In this example, it is 9.

Debits

If, after 28 days, parts have not been received, or the WPC has not been contacted with an approved explanation for non-return of parts, the WPC
will submit a total claim debit to the WINS process. The Debit Reason Code WP will be assigned to each debit case. If the dealer has any questions
regarding a debit, please log on to the gmwpc.com website to obtain the reason. The WPC has NO authority to waive or reverse debits after
issuance; the GM Area Service Manager (AVM) or the DSPM (Isuzu) must be contacted in these instances.

Regarding debits, the following responses are unacceptable at any time and will result in a debit:

^ WPC received the part without paperwork.

^ Dealer never received the original request.

^ The dealer sent the part to an unapproved location.

^ The dealer returned the part for Core Value.

^ WPC received paperwork without the part.

^ The dealer scrapped the part prior to retention period.

^ Dealer sent wrong part.

Parts Prep. for Shipping/Parts Reten. & Requests


Part Preparation for Shipping

The return request message will list specific claims for which parts (and repair orders) are to be returned as follows:

ONLY PARTS ASSOCIATED WITH THE LABOR CODE ARE TO BE RETURNED AND SHOULD BE BUNDLED TOGETHER AND
SHIPPED USING THE UPS/ARS SHIPPING LABELS (WPC002). PLASTIC PACKING BAGS (WPC001) ARE AVAILABLE FROM THE
WPC FOR THE PROTECTION OF THE PAPERWORK TO BE INCLUDED WITH THE PARTS (LEGIBLE COPIES OF THE REPAIR
ORDER - WITH THE TECHNICIAN'S COMMENTS - AND THE CPR "REQUEST"). THESE BAGS MUST BE SECURELY ATTACHED TO
THE APPROPRIATE PARTS.

When additional UPS/ARS shipping labels or plastic bags are needed, complete the Material Request form (WPC005) and fax it to the WPC at
(248) 371-9005 OR via e-mail to WARRANTY PARTS CENTER USA@gm.com. (Refer to Form WPC005 as shown in this bulletin.) Supply
requests are shipped via UPS within 24 hours.

There may be instances where multiple return requests are listed on one message. When this occurs, dealers should ship each individual request in a
separate box with its own UPS/ARS label. DO NOT SEND MULTIPLE REQUESTS IN THE SAME BOX. Copies of the "request" and repair
order must be attached to each part sent to the WPC. The dealer should highlight the particular request pertaining to the part and place the folded
paperwork in the plastic packing bag with the highlighted Request Number facing out. This process will assist the WPC in handling and crediting
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 232
Chevrolet Venture V6-3.4L VIN E 2557
the dealership for returning the part in a timely manner. When possible, the container from the new/replacement part should be used for the return
of the failed part. However, all previous labeling on the box should be removed prior to re-use. Parts containing or soaked by fluids, such as oil or
fuel, MUST be drained, wiped clean and placed in an appropriate packing container and securely packaged in order to prevent leakage or
contamination.

When returning parts, complete the UPS/ARS shipping label by writing in the dealer name, address, city, state and zip code. The Ref. # field should
contain the Request Number being returned. Attach the label to the package and detach the lower portion for dealer records. The lower portion of
the label contains the shipment tracking number and should be attached to the dealer's "Warranty Parts Center Shipping Log" (Refer to Warranty
Parts Center Shipping Log as shown in this bulletin). This UPS/ARS receipt can be used for tracking purposes through UPS. Status of UPS
shipments is available via UPS tracking at 1-800-742-5877 or via the Internet at www.ups.com or www.gmwpc.com.

If a part (and appropriate paperwork) cannot be shipped via UPS due to size or weight limitations, the following GM-approved common carrier
(LTL) must be used to return the parts "Third Party Freight Collect" to the WPC.

A partially completed Yellow Freight bill of lading is available by request as shown through the WPC. Dealers should submit a Material Request
form and indicate quantity desired. The dealer is responsible for completing the shipper information (dealer name and address) and description and
weight of shipment on the Yellow Freight bill of lading.

When this process is used, the dealer will not need to pre-pay shipments to the WPC. Parts delivered by any other common carrier (LTL), will be
rejected by the WPC and returned to the dealership.

In order to prevent paperwork loss on common carrier (LTL) shipments, attach two copies of the DCS message and repair order as follows:

^ Attach one copy to the inside of the crated shipment (attached to the part).

^ Attach one copy to the Bill of Lading.

If there are special packaging costs, they should be included as a Net Item amount when submitting a Z7200 claim. Special packaging situations
may include crating an engine assembly, reassembly of components, or draining and sealing components in order to prevent leakage during
shipment. Appropriate handling charges for these situations should be calculated at a rate for unskilled labor (not at the warranty or retail labor rate)
and appropriately documented on the Z7200 claim.

Parts Retention and Requests

The GM P & P states all warranty core parts must be held until receipt of claim payment. THIS INCLUDES, BUT IS NOT LIMITED TO,
ENGINES, TRANSMISSIONS, STARTER MOTORS, CATALYTIC CONVERTERS, PCM, POWER STEERING PUMPS, STEERING
GEARS, AND ALTERNATORS/GENERATORS. On the date of claim payment, the dealer should also verify receipt of CPR requests for any core
parts paid on that claim cycle. If NO CPR request is received for the paid core parts, the dealer should return those parts to the appropriate Core
Return Center. When the CPR requested parts are returned to the WPC, the core allowance should be submitted as a Net Item amount on the
reimbursement claim.

Any core Product Feedback Forms received with a replacement part must be completed and returned with the part and Repair Order to the WPC.

Any core parts returned to the core center prior to claim payment will be subject to an automatic debit.

Furthermore, the GM P & P also states that all other warranty parts must be held for 15 days after receipt of claim payment.

On those occasions when a part is not available for return to the WPC, fax or Lotus Notes a completed Pants Waiver Form with an explanation.
(Refer to Form WPC006 as shown in this bulletin.) Please note that not all explanations will prevent a debit.

Hazardous Material/Tires
Hazardous Material

The WPC is not certified to receive nor handle hazardous material; therefore, lead batteries (see note *** below), air bags, fuel tanks or items that
contain explosive material should not be sent to the WPC. If a request is received and the associated part is considered hazardous, a WPC Parts
Waiver should be completed, explaining that the part is hazardous, and faxed to the WPC. The Parts Waiver must be received within 28 days of
original request to avoid a debit being issued.

*** The new ACDelco AGM lead acid battery is considered non-hazardous for purposes of transportation and can be returned to the WPC.
However, if a dealership receives a WPC request to return this particular battery, the container must be clearly marked "NON-SPILLABLE PER
49CFR 173.159(d)." At the present time, this is the ONLY battery which can be safely returned to the Warranty Parts Center. The ACDelco battery
can be returned using the regular pre-paid UPS/ARS labels provided by the WPC.

Tires

Most tires replaced under the New Vehicle Limited Bumper-to-Bumper Warranty must be returned to the tire manufacturer. However, there will be
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 233
Chevrolet Venture V6-3.4L VIN E 2558
instances when the WPC will request tires to be returned. When a WPC request is received at the dealership, all instructions outlined in this bulletin
should be followed (paperwork inclusion and shipping).

Effective immediately, tires must be retained until receipt of claim payment. The WPC will request a tire(s) return on the same day the credit memo
is received at the dealership. If no WPC request is received, the dealer should return the tire(s) per the official tire bulletin. Dealers are encouraged
to submit warranty claims as soon as possible in order to alleviate storage of tires. All vehicle tires replaced on the repair order are to be returned to
the WPC and the appropriate paperwork must be attached to each tire returned.

Upon claim submission, the dealer must submit the $25 handling allowance per repair order in the "parts amount" field and the part number
09592318 in the Part Number field regardless of manufacturer. This process allows the WPC to identify a tire for return. It is very important for the
dealership to retain tires until the claim is paid.

Exchange Program Parts/Special Parts Request/R.O. Only Requests


Exchange Program Parts

The GM WPC has assumed responsibility for obtaining special new model exchange program parts from dealerships. The following exchange
process has been implemented at the WPC:

1. The GM Service Bulletin will advise dealers of an exchange. Dealers will be directed to call Technical Assistance (TAC).

2. TAC takes the call from the dealer and qualifies and approves the exchange. TAC will notify the appropriate parties to release and ship a
replacement part to the dealer.

3. At the same time, TAC will notify the WPC that an exchange is taking place at the dealership. The WPC will create an "Exchange Special
Part Request" and assign a request number which will begin with an "EX" followed by seven digits. This WPC original request will be faxed
to the contact person of the dealership within 24 hours of the call to TAC. When the Parts Manager receives the failed parts from the
technician, all appropriate paperwork should be attached (including the Exchange Special Part Request and copy of Repair Order (with
technicians comments) and shipped to the WPC using the shipping procedures outlined in this bulletin.

4. Electronic reminders notifying the dealer of non-receipt of exchange parts will be sent by the WPC in the same manner as in the past. For an
example of reminders, please refer to the examples found later in this bulletin. The Repair Order Date on the request message will appear as
the date the Exchange Special Part Request was generated by the WPC.

5. If the part is not received at the WPC within 28 days from the original request date, the claim will be submitted to WINS as a debit.

Special Parts Request

Dealers may be contacted by the WPC to return "one-of-a-kind" parts for specific engineering analysis that have not been identified in the normal
process. In those instances where a special part is needed, the dealership will receive via fax from the WPC a "SPECIAL PART REQUEST" form.
The process for returning special parts is the same as explained in this bulletin. A copy of the Special Part Request must be included in the shipment
and the box/crate labeled "SPECIAL PART REQUEST." The Special Part Request form contains a section for the dealership to use if the part is
requested, at a later date, via the normal CPR return process.

Repair Order Only Requests

Important:
Never return a "Repair Order Only" request to the WPC.

If a "Repair Order Only" request (refer to the Request for Repair Order Only Example as shown in this bulletin) is received, return legible copies of
the R.O., including technician comments, directly to the requester using the mailing label provided on the CPR request (the address will be
surrounded by ***). Do not use the UPS/ARS label and DO NOT RETURN PARTS on this type of request. When returning "Repair Order Only"
requests, use REGULAR US Postal Service mail. Do not use Registered mail of any type.

WPC Forms /Return & Method of Reimbursement/Dealer Feedback


WPC Forms

Copies of Forms (Parts Waiver, Material Request and the Yellow Freight Bill of Lading) are available via the WPC website at www.gmwpc.com or
by calling or faxing WPC Customer Assistance (248-371-9901/9902 or fax 248-371-9005).

Return Reimbursement

The following conditions qualify for dealer reimbursement:

1. Administrative Allowances

Enter as "Labor Hours" - A range from 0.0 to 0.3 hours may be claimed for each line involving the return of parts (and copies of R.O.s
including technician comments). The time requested for reimbursement depends on the complexity of the request as determined by the dealer.
A range from 0.0 to 0.2 hours can be claimed for each line where repair order only copies are returned, again as determined by the dealer.
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 234
Chevrolet Venture V6-3.4L VIN E 2559

2. Shipping Expenses

Enter as "Net Item" - There will be no dealer incurred postage or shipping costs associated with parts returned to the WPC. However, any
postage charges for "repair order only" requests will be reimbursed.

3. Packaging Material Costs (where applicable) Enter as "Net Item" - Packaging material costs include such things as boxes, tape, etc. Labor
charges (for crating an engine assembly, draining and sealing components in order to prevent leakage during shipment, etc.) associated with
packaging costs are to be calculated and billed at a cost for unskilled labor and not at the dealer's warranty or retail labor rate.

4. GMSPO Core Part Allowance Amounts (where applicable)

Enter in "Net Item."

Method of Reimbursement

Each return request may be recorded using a separate repair order or up to ten requests may be (physically) listed on a single repair order. Entries
must include the VIN, request number, number of parts returned, and associated costs.

When submitting a single return request for reimbursement, use the normal submission procedures and Labor Operation Z7200 with claim type "F."
In order to receive reimbursement for multiple part return requests, choose one of the VINs for the one line claim. Submit for the total of all
corresponding charges (up to 10 requests) on that one line. Refer to the description of claim submission entries shown. All related documentation,
including a copy of the CPR return request, must be retained for future reference in accordance with the GM Service Policies & Procedures
Manual.

Dealer Feedback

The WPC recognizes the need to provide information regarding our progress and accomplishments in product improvements as a direct result of the
Corporate Parts Return program. Information gathered by the WPC will be provided to dealers in the form of a newsletter.

Important WPC Information to Remember

Parts Ret. Req/R.O. Only Examples


Part Return Request Example

GM WARRANTY PARTS CENTER RETURN REQUESTS FOR DEALER XXXXX - CLAIM MEMO XXX.

Below are parts and repair orders which are required for product review. The following must be returned to the Warranty Parts Center at:

WARRANTY PARTS CENTER


45 NORTHPOINTE DRIVE
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 235
Chevrolet Venture V6-3.4L VIN E 2560
ORION, MI 48359

USE THE PROVIDED PRE-PRINTED AND PRE-PAID UPS/ARS LABELS TO SHIP THE FOLLOWING:

^ Copy of the request below

^ Repair order (including technician comments)

^ Only parts associated with the labor code

ALL FLUIDS MUST BE DRAINED FROM PARTS BEING RETURNED. Place the above items in a plastic bag and securely attach to part prior
to shipping. Each request should be shipped individually.

Shown are part requests that have not been received at the Warranty Parts Center as of this date. If your records indicate that you have returned the
requested part (allow 7 days for shipping and handling), it is imperative that you follow-up with the WPC at 248/371-9901/9902 (or fax at
248/371-9005) to resolve the issue and avoid possible debit.

Request For Part Return/Repair Order Only/Reminder Example

GM WARRANTY PARTS CENTER RETURN REQUESTS FOR DEALER XXXXX - CLAIM MEMO XXX.

Below are parts and repair orders which are required for product review. The following must be returned to the Warranty Parts Center at:

WARRANTY PARTS CENTER


45 NORTHPOINTE DRIVE
ORION, MI 48359

Shown are R.O. Only requests which should be returned to the requestor via the post office using the mailing label provided. No R.O. Only
requests should be returned to the Warranty Parts Center.
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 236
Chevrolet Venture V6-3.4L VIN E 2561

Shown are part requests that have not been received at the warranty parts center as of this date. If your records indicate that you have returned the
requested part (allow 7 days for shipping and handling), it is imperative that you follow-up with the WPC at 248/371-9901/9902 (or fax at
248/371-9005) to resolve the issue and avoid possible debit.

Request For Repair Order Only Example

GM WARRANTY PARTS CENTER RETURN REQUESTS FOR DEALER XXXXX CLAIM MEMO XXX.

Shown are R.O. Only request which should be returned to the requestor via the post office using the mailing label provided. No R.O. Only request
should be returned to the Warranty Parts Center.

Shown are part requests that have not been received at the Warranty Parts Center as of this date. If your records indicate that you have returned the
requested part (allow 7 days for shipping and handling), it is imperative that you follow-up with the WPC at 248/371-9901/9902 (or fax at
248/371-9005) to resolve the issue and avoid possible debit.

Reminders Only Example

GM WARRANTY PARTS CENTER RETURN REQUESTS FOR DEALER XXXXX - CLAIM MEMO XXX.

Shown are part requests that have not been received at the Warranty Parts Center as of this date. If your records indicate that you have returned the
requested part (allow 7 days for shipping and handling), it is imperative that you follow-up with the WPC at 248/371-9901/9902 (or fax at
248/371-9005) to resolve the issue and avoid possible debit.
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 237
Chevrolet Venture V6-3.4L VIN E 2562

Warranty Parts Center Shipping log


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 238
Chevrolet Venture V6-3.4L VIN E 2563

Parts Waiver
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 239
Chevrolet Venture V6-3.4L VIN E 2564

Material Request

Technical Service Bulletin # 01-00-89-010 Date: 010601

Diagnostic Worksheet - Usage


File In Section: 00 - General Information

Bulletin No.: 01-00-89-010

Date: June, 2001

WARRANTY ADMINISTRATION

Subject:
Information on Use of Diagnostic Worksheet

Models:
2002 and Prior Model Year Passenger Cars and Trucks

This bulletin is being revised to add model years and update the text. Please discard Corporate Bulletin Number 58-01-01 (Section 1 - General
Information).

During the last several years, we have made great strides in the quality of services we deliver to our customers. Customer satisfaction levels are
increasing, but as these levels go up, so do our customers' expectations. In order to remain competitive and retain our valuable customers in the
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 240
Chevrolet Venture V6-3.4L VIN E 2565
future, we will have to keep improving customer satisfaction. The key to future improvement will be enhancing communications with our
customers. One of the most challenging aspects of our business is to communicate the concern from the customer to the technician. The more
clearly the technician understands the concern and its symptoms, the more likely the problem will be fixed right the first time." With that in mind,
there has never been a better time to revitalize the use of a diagnostic worksheet. GM Service Operations is releasing a revised diagnostic worksheet
based on input from GM Technical Assistance, Service Engineers, Service Manual Writers and a select group of retail Dealer Service Directors.
The new diagnostic aid, streamlined to a single sheet, reflects today's product without sacrificing content. Dealers/retailers report they are very
helpful in reducing shop comebacks, increasing technician productivity and producing satisfied customers. Here are a few of the many benefits
gained from using the worksheets:

^ Reduces "no trouble founds"

^ Increased customer involvement

^ Customer perception of "they really listen and understand"

^ Saves time during peak write-up periods

^ Reduces recontacting customers for additional information

^ Improves night drop box information

^ Ensures all the right questions are asked a write-up


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 241
Chevrolet Venture V6-3.4L VIN E 2566

An example of the GM-wide diagnostic worksheet. available for use in all dealership retail facilities, at the end of this bulletin. This example may
be printed and reproduced locally. Dealers in the US may also contact Dealer Support Materials at 1-800-235-8521 and request Form Number
DWS-Q to obtain these worksheets at no cost. Please limit your requests to a reasonable quantity. If you have any comments or suggestions
regarding this form. call GM Service Operations Techline Customer Support Center at 1-800-828-6860.

The information below contains ideas and thought- starters that may be helpful in getting you started using the diagnostic worksheet.

^ Have your service consultant fill out this form with the customer whenever possible.

^ Place the form in your night drop box for the customer to fill out along with an instruction sheet to help them understand what to do.

^ Have a porter or greeter give the form to customers while they wait in line during peak morning rush and ask them to fill it out. It will save time
for all concerned and improve the quality of information received from the customer.

^ Make sure to attach the form to the paperwork that goes to the technician.

^ Review the form at your service department introduction during the new vehicle delivery process.

^ Require that you personally see a copy of all worksheets filled out on shop comebacks.

^ Hold an all-service department meeting to get employee buy-in and their ideas on how to make the form effective.

^ Put a worksheet in the glove box of all departing service customers.

^ Cover this as part of your new owner orientation clinics.

There are many other ways to utilize the concept, but as with every other idea, successful implementation depends on employee involvement and
buy-in.
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 242
Chevrolet Venture V6-3.4L VIN E 2567

DISCLAIMERTechnical Service Bulletin # 00-00-89-021 Date: 000801

Cross Line - Warranty Information


File In Section: 00 - General Information

Bulletin No.: 00-00-89-021

Date: August, 2000

WARRANTY ADMINISTRATION

Subject:
Cross-line Warranty

Models:
2001 and Prior Passenger Cars and Trucks

Attention:
All U.S. General Motors Dealers

Cross-line warranty capability was recently announced to wholesale personnel and GM dealers via a DCS administrative message and a hard copy
letter was sent to GM dealers only. The following bulletin provides additional information for dealers wishing to perform cross-line warranty
repairs. We have also provided a section for Frequently Asked Questions that will address additional inquiries we have received since the release of
the DCS message.

One of the benefits of cross-line warranty is the ability to perform repairs for customers in an emergency situation. Since emergency situations can
be subjective from a customer's perspective, the dealer will need to determine if the situation merits urgent attention. While additional tools or
training are not required, dealers should exercise good judgment regarding their ability to perform the repair. The overall intent is to provide an
opportunity for customer satisfaction in a potentially negative ownership experience. If the dealer has questions regarding a specific situation, they
should be reviewed with the Area Service Manager (AVM).

The second instance in which cross-line warranty can be performed is for used vehicles. Any used GM vehicle resold by a GM dealer may obtain
warranty service from the selling GM dealer regardless of the dealer's new vehicle franchise. This will be helpful to dealers who have sold a used
vehicle to a customer that is different from their franchise and will not have to turn the customer away for any remaining warranty work.

Cross-line warranty is not to be a replacement for the GM Certified Used Vehicle process. This process still remains intact and is administered by
the GM Certified Used Vehicle Department.
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 243
Chevrolet Venture V6-3.4L VIN E 2568

Lastly, cross-line warranty capability is now available for designated commercial light duty trucks. Designated commercial dealers are defined as
those dealers that meet the standards of the Light Duty Commercial Program and have signed the Dealer Participation Agreement. The matrix
should help in identifying which light duty commercial vehicles qualify for cross-line repairs by designated commercial dealers.

Frequently Asked Questions

When can I start to perform cross-line warranty repairs and which model year vehicles can I service?

You can now submit cross-line warranty claims for any model year vehicle with warranty remaining, provided that the repair fails within one of the
three established and previously stated guidelines.

Can I promote my cross-line warranty capability?

No. After receiving input from both the National Dealer Council and GM, GM agreed that in order to protect brand identity and dealers' equity in
their franchise, dealers will not be permitted to advertise cross-line warranty service by any means including direct mail or other dealer mailings.
Any violation of this could result in on-site consultation, audit, dealer charge back or termination of cross-line capability.

Can I perform a recall repair if one is outstanding on a used vehicle or one that has come into my shop as a result of an emergency situation? Yes.
The campaign should be completed if the customer is at the dealer under one of the three established and previously stated guidelines. However,
dealers should always check General Motors Vehicle Inquiry Service (GMVIS) to see if there is an outstanding campaign prior to the vehicle being
sold. Dealers also need to make sure that they have the right tools and training to perform any recall. How do I submit a warranty claim on a
cross-line warranty repair?

No changes are necessary to the warranty claim payment submission process in accommodating cross-line warranty repairs. Submission of
cross-line warranty repair claims within the warranty period are to be done following established business processes and practices. Wholesale
authorization must be obtained for any claim outside the warranty period on a non-franchised vehicle.

Will cross-line customers be excluded from receiving CSI surveys?

No. Cross-line warranty repairs are projected to be minute and are not considered to be the core repair business of the dealership. In addition,
exclusion would be difficult and would interfere with the statistically valid selection process CSI has in place.

Why are Saturn and Saab excluded from participating in cross-line warranty? Saturn and Saab each have unique warranty claim payment and parts
distribution systems. This would make it particularly difficult for non-Saturn and Saab dealers to procure parts or obtain reimbursement for the
repair.

Does cross-line warranty capability alter the Roadside Assistance policies?

No. Roadside Assistance parameters require the vehicle be directed first to the selling dealer when practical, then to the closest franchised dealer,
and last, to the nearest GM dealer.
Technical Service Bulletin # 68-05-03 Date: 960601

Warranty - Goodwrench Service Lifetime Service Guarantee


File in Section:
Warranty Administration

Bulletin No.:
68-05-03

Date:
June, 1996

WARRANTY ADMINISTRATION

Subject:
Goodwrench Service Plus Lifetime Service Guarantee
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 244
Chevrolet Venture V6-3.4L VIN E 2569

Models:
All Models - All Years

The information in this bulletin applies to all divisions excluding Saturn and GM of Canada.

The purpose of this bulletin is to explain details of the the Lifetime Serve Guarantee (LSG).

LSG Coverage Requirements

The GM vehicle owner and original purchaser of a covered part must return to the original servicing GM dealership and present repair order and
warranty folder.

Eligible Parts

^ Air Conditioning Accumulators

^ Air Conditioning Compressors

^ Air Conditioning Condensers

^ CV Joint/Boot Seal Kits

^ EGR Valve

^ Fuel Injectors

^ Fuel pumps

^ Individual Ignition Wires

^ Ignition Coils

^ Ignition Wire Sets

^ Ignition Modules

^ New/Remanufactured Generators

^ New/Remanufactured Starter Motors

^ Oxygen Sensors

^ Shock Absorbers/Struts

^ Throttle Body Injectors

^ Water Pumps

General Information

^ Lifetime Service Guarantee is only available to and offered by participating GM Goodwrench Service Plus dealers/retailers.

^ Parts warranty handling allowance is per the General Motors Service Policy and Procedures Manual - 40% for 1994 and later model years, and
30% for 1993 and prior years.

^ Parts sold over the counter are not covered under LSG.

^ A customer paid repair order is required for future part coverage consideration.

^ Parts installed on vehicles in dealer inventory (new or used) are not eligible for LSG. Only a customer paid repair by the original retail
purchaser.

^ Towing is not covered under the LSG.

Any questions regarding the LSG or GSP should not be directed to your GMSPO representative.
Technical Service Bulletin # 99-00-84-021B Date: 000401

Warranty - GM Dealer Parts Procurement


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 245
Chevrolet Venture V6-3.4L VIN E 2570
BULLETIN NUMBER:
99-00-84-021B

SECTION:
00 - General Information

DATE:
April, 2000

SUBJECT:
Expediting Parts

MODELS:
2000 and Prior Passenger Cars and Trucks

ATTENTION:
"GM of Canada" and "IPC" Dealers are not authorized to utilize this Service Bulletin.

This bulletin is being revised to exclude GM of Canada Dealers. Please discard Corporate Bulletin Number 99-00-84-021A (Section 00 - General
Information).

The following policy is in place to address those occasions when it is necessary to procure a part from another local GM dealer or by express
shipping (CSO-3).

General Motors is making a significant commitment to help reduce comebacks and maintain the level of customer service demanded by customers
in your dealership. The following procedure provides dealers with a tool to help achieve total customer satisfaction during any applicable GM
warranty period. This procedure will provide reimbursement of expenses beyond normal dealer parts costs, up to 25% greater than the GMSPO
dealer net price or $100 (whichever is less), for parts obtained locally. Expenses incurred for expediting GM ordered parts (CSO-3) not in dealer
stock can also be reimbursed. This procedure should be utilized only during any applicable GM warranty coverage period.

Effective immediately, dealers will be required to input the part number without the part cost on all Z5000 and Z5001 claims. In instances where
the integrated system automatically loads a part price, the calculation/price should be overridden so that the part price is zero. If multiple parts were
procured, the total number of parts expedited should be inputted in the part count field. In those instances, the part with the greatest cost should be
entered into the part number field.

All records and invoices in support of your claim must be retained in vehicle history record in accordance with Article 1.6 of the GM Service
Policies and Procedures Manual. Parts expediting is not considered to be an add-on repair to the Repair Order, and does not require service
management approval (Article 1.6.2.p.).

You may submit a claim for reimbursement under either of these operation numbers:

- Z5000 for parts obtained from a local GM dealer

- Z5001 for CSO-3 freight expenses

RECOMMENDED PARTS EXPEDITING PROCEDURE

1. Inform the customer if a part availability issue exists, and if eligible, offer appropriate Courtesy Transportation.

2. Contact a local dealer in an attempt to obtain the needed parts for same day repair. GM will reimburse the difference between the dealer price
and the actual cost, up to the trade price, as published in the GMSPO Parts and Accessories Price Guide. If no trade price is listed,
reimbursement will not exceed 25% of GMSPO dealer cost or $100, whichever is less. In either case, the reimbursement request must not
exceed $100.

3. In the event the needed part is not available locally, it should be ordered on a Customer Order from GM Parts. If the part is needed for next
day repair, order the part CSO-3 (or use CSO if overnight service is not available in your area). GM will reimburse the shipping expenses.

If a part is on back-order, IMMEDIATELY upgrade the order to a SPAC case.

4. Please review the parts application and add the part to your normal inventory, if appropriate.

5. Always keep the customer informed of the status of the repair.

CLAIM SUBMISSION PROCEDURE Z5000 - PART OBTAINED LOCALLY

If you do not have the required part in stock and are able to obtain it locally, GM will reimburse you for the additional dealer trade markup. You
may have to pay to obtain the part from another local GM dealer. The allowance is for up to 25% of the GMSPO dealer cost or $100, whichever is
less.

The following example uses an evaporator core that you need. It has a dealer net cost of $199.80. The part is being obtained by you from another
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 246
Chevrolet Venture V6-3.4L VIN E 2571
local GM dealer (Hometown Motors), who has it in stock.

You are able to purchase the evaporator core from Hometown Motors at a 20% dealer trade price of $240.00 ($199.80 + 20% = $240.00), a $40.20
markup. When your dealership submits a warranty claim, the part amount will be figured on the dealer net cost of $199.80 at the normal dealer
markup (30% for 1993 and prior or 40% for 1994 and newer). For example, $199.80 + 30% = $259.74. The warranty repair order would use labor
operation D3320 with the part amount of $259.74. To recover the 20% markup of $40.20 that you paid Hometown Motors, you would submit an
additional warranty claim for operation Z5000 for a net item amount of $40.20.

The detail elements for this claim may appear on your computer screen in this manner (some screen layouts may be different).

CLAIM SUBMISSION PROCEDURE Z5001 - PARTS ORDERED CSO-3

If a CSO-3 order is necessary, the freight expense will be reimbursed. A claim for the repair should be submitted in the normal manner. An
additional claim/case should be submitted for the actual amount of the freight expense.

- With one part ordered, request the entire freight charges for the CSO-3 order.

- With more than one part shipped from GMSPO in the same box, refer to the RAPID 2000 Advise of Shipment Answer back for itemized
freight cost for each part.

If the evaporator core in the previous example had been obtained from GMSPO through a CSO-3 parts order, the following example shows correct
warranty claim submission for the additional cost. The published GMSPO dealer price for the core is $199.80. The GMSPO charges associated
with the order are only freight charges, as all surcharges are eliminated with this implementation of the new GM Parts system. The repairing
division would reimburse any applicable freight charges, submitted under labor operation Z5001 as a net amount (as an example, $18.00 express
shipping charges).

The claim submission is shown in the example.


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 247
Chevrolet Venture V6-3.4L VIN E 2572

The detail elements for this claim may appear on your computer screen in this manner (some screen layouts may be different).

Refer to the table which details the type of claims (including special claims) when parts expediting is applicable for the covered vehicle (or part)
failure. Please refer to your WINS Claim Processing Manual, Section VII for special claim type details. The Z5000 and Z5001 operations DO NOT
require a special claim type.

CLAIM TYPE COMPATIBILITY

Important: No additional dealer markup on Z5000 or Z5001 is allowed.

Those operations are intended to reimburse dealers for the actual expense that occurred, as detailed above.

Disclaimer

Technical Service Bulletin # 99-00-89-016 Date: 990901

Warranty - Labor Time Guide Updates, 09/99


File In Section: 00 - General Information

Bulletin No.: 99-00-89-016

Date: September, 1999

WARRANTY ADMINISTRATION

Subject:
September, 1999 Labor Time Guide Updates

Models:
1994-2000 Passenger Cars and Trucks

This bulletin addresses changes to the published General Motors Labor Time Guides. These changes (new or revised) are the result of new time
studies and/or dealer "Requests For Review" being handled by the GM Service Operations Group. They are effective upon receipt. All changes will
appear in the next printing of the Labor Time Guide.
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 248
Chevrolet Venture V6-3.4L VIN E 2573
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 249
Chevrolet Venture V6-3.4L VIN E 2574
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 250
Chevrolet Venture V6-3.4L VIN E 2575
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 251
Chevrolet Venture V6-3.4L VIN E 2576
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 252
Chevrolet Venture V6-3.4L VIN E 2577
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 253
Chevrolet Venture V6-3.4L VIN E 2578

Important:
Please retain any changes made to the A, B, D and L Car Labor Time Guides as these vehicles have been discontinued since 1997 and the Labor
Time Guides will not be republished. Changes to the P/H Truck Chassis should also be retained. The vehicle was discontinued in December,
1998. Please note: Labor Time Guides for these discontinued vehicles will not be republished.

Technical Service Bulletin # 99-05-25-003A Date: 001001

Brakes - ABS Exchange Program Ended


File In Section: 05 - Brakes

Bulletin No.: 99-05-25-003A

Date: October, 2000

EXCHANGE PROGRAM

Subject:
Cancellation of DBC 7 Diagnostic Assistance and Parts Return Program

Models:
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 254
Chevrolet Venture V6-3.4L VIN E 2579
1999 Buick Century, Regal
2000 Chevrolet Cavalier, Impala, Malibu, Monte Carlo, Venture
2000 Oldsmobile Silhouette
2000 Pontiac Sunfire, Montana

This bulletin is being issued to cancel the Delphi Chassis DBC 7 Diagnostic Exchange Program. Please discard Corporate Bulletin Number
99-05-25-003 (Section 5 - Brakes).

Effective September 30, 2000 the Delphi Chassis DBC 7 service parts are released from restriction:

At this time, dealerships may begin to order and stock the released service parts through normal GMSPO channels.

Option Code Identification:

^ Antilock Brakes (ABS) - JL9

^ Enhanced Traction Control System (ETS) - NW7

^ Traction Control System (TCS) NW9

DisclaimerTechnical Service Bulletin # 00-05-22-004 Date: 000501

Brake Fluid - Level & Filling Recommendations


File In Section: 05 - Brakes

Bulletin No.: 00-05-22-004

Date: May, 2000

INFORMATION

Subject:
Brake Fluid Level and Filling Recommendations

Models:
2001 and Prior Passenger Cars and Trucks

Many dealers and after-market repair shops advertise multi-point fluid "top-ups" in conjunction with oil changes or regular maintenance packages.
These offers often include adding brake fluid to the master cylinder reservoir. There are only two reasons why the brake fluid level in the brake
reservoir might go down. The first is that the brake fluid level goes down an acceptable level during normal brake lining wear. When the linings are
replaced, the fluid will return to it's original level. The second possible reason for a low fluid level is that fluid is leaking out of the brake system. If
fluid is leaking, the brake system requires repair and adding additional fluid will not correct the leak. If the system was properly filled during
delivery of the vehicle, no additional fluid should be required under most circumstances between brake pad and/or shoe replacements. This
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 255
Chevrolet Venture V6-3.4L VIN E 2580
information can be reinforced with the customer by referring them to the Brake Fluid section of their vehicle's Owner's Manual.

Guidelines

GM vehicles have incorporated a variety of brake fluid reservoir styles. The following guidelines are restricted to the plastic bodied fluid reservoirs
and do not affect the original service recommendations for the older style metal bodied units.

You may encounter both black plastic and translucent style reservoirs. You may have reservoirs with:

^ A MAX fill mark only

^ A MIN fill mark only

^ Both MAX and MIN marks

The translucent style reservoirs do not have to have the covers removed in order to view the fluid level. It is a good practice not to remove the
reservoir cover unless necessary to reduce the possibility of contaminating the system. Use the following guidelines to assist in determining the
proper fluid level.

Important:
When adding brake fluid, use Delco Supreme II(R) Brake Fluid, GM P/N 12377967 or equivalent brand bearing the DOT-3 rating only.

Important:
At no time should the fluid level be allowed to remain in an overfilled condition. Overfilling the brake reservoir may put unnecessary stress on
the seals and cover of the reservoir. Use the following guidelines to properly maintain the fluid level. If the reservoir is overfilled, siphon out
the additional fluid to comply with the guidelines below.

Important:
If under any circumstance the brake fluid level is extremely low in the reservoir or the BRAKE warning indicator is illuminated, the brake
system should be checked for leaks and the system repaired in addition to bringing the fluid level up to the recommended guidelines outlined
below. A leaking brake system will have reduced braking performance and will eventually not work at all.

Important:
Some vehicles have reservoirs that are very sensitive to brake fluid levels and may cause the BRAKE indicator to flicker on turns as the fluid
approaches the minimum required level. If you encounter a vehicle with this concern, increase the fluid level staying within the guidelines
outlined below.

^ If the reservoir has a MAX level indicator, the reservoir should be returned to the MAX marking only at the time new brake pads and/or shoes
are installed. If the reservoir fluid level is at the half-way point or above do not attempt to add additional brake fluid during routine fluid checks.

^ If the reservoir has both MAX and MIN indicators, the fluid level should be maintained above the MIN indicator during routine fluid checks
and returned to the MAX indication only after new brake pads and/or shoes are installed.

^ For reservoirs with only a MIN indication, the fluid level should be maintained above the MIN indicator during routine fluid checks. Return the
reservoir fluid level to full only after installing new brake pads and/or shoes. A full reservoir is indicated on translucent, snap cover reservoirs
by a fluid level even with the top level of the view window imprinted into the side of the reservoir. On screw top models in black or translucent
plastic, the full level is just below the bottom of the filler neck.

Parts Information

Part Number Description


12377967 Brake Fluid

Parts are currently available from GMSPO.

DisclaimerTechnical Service Bulletin # 03-06-04-012A Date: 050810

Electrical - Harness Connection Inspection


Bulletin No.: 03-06-04-012A

Date: August 10, 2005

ADVANCED SERVICE INFORMATION


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 256
Chevrolet Venture V6-3.4L VIN E 2581

Subject:
Inspection of All Related Wiring Harness Connections When Diagnosing Miscellaneous DTCs, Intermittent Driveability Concerns, Hard Start, No
Start, Incorrect Gauges, Inoperative Air Conditioning Systems, Service Engine Soon Lamps Illuminated, 4WD Lamp Illuminated, Instrument Panel
Gauges Inoperative, Cruise Inoperative

Models:
2006 and Prior Cars and Light Duty Trucks
2003-2006 HUMMER H2
2006 HUMMER H3
2005-2006 Saab 9-7X

Supercede:

This bulletin is being revised to add models, model years and additional information. Please discard Corporate Bulletin Number 03-06-04-012
(Section 06 - Engine/Propulsion System).

When servicing a vehicle for any type of customer concern, the following steps are imperative. Inspect and ensure the integrity of all related wiring
harness connectors. If the wiring harness connectors are not properly put together or engaged before they are locked together, numerous types of
intermittent conditions may occur, which may include any of the symptoms listed above and possibly others.

The first step in any type of electrical diagnosis is a visual and physical inspection of the wiring harness connectors for integrity. Many times, the
vehicle may be repaired just by disconnecting and reconnecting the connectors. As with all repairs to wiring harness connectors and terminals, a
pull test of the terminals within the connector should be performed. A pull test is performed by inserting the proper size terminal test tool (not a
paper clip) into the terminal to determine whether or not the terminal is making good contact, or whether the terminal has been damaged from the
prior improper connection or lack of connection.

Note:
Most terminals used in current module connectors (ECM, BCM, EBTCM and the like) are small 0.64 mm sq. terminals and can be damaged by
probing with the wrong tool.

The J 3561 6-64A or B probe has been designed for these terminals that may be both a round or square design.

For example, if the Connector C2 of the engine wiring harness to the Powertrain Control Module (PCM), for the 2.2L equipped Cavalier or Sunfire
is not properly seated into the PCM:

^ The cam lock lever may close, however improperly.

^ The cam lock lever may even snap out of position.

^ The vehicle may have an intermittent condition with any one of the components which are controlled or monitored by the PCM.

THE CAM LOCK LEVER IS DESIGNED TO PULL (OR ASSIST) THE CONNECTOR INTO ITS FINAL POSITION ONCE IT HAS BEEN
PRESSED STRAIGHT INTO THE PCM HEADER PAST THE INITIAL DETENT, ALLOWING THE LEVER TO BE MOVED INTO THE
LOCKED POSITION. It is not only a retainer but an assist during the connection process . When the wiring harness connector is properly
connected to the PCM, a snap will be heard when the connector is in position to be fully seated. The cam lock lever may then be closed. The cam
lock lever will then do its designated job as both an assist and ensuring the connector does not come apart due to vibration or other types of
conditions found in vehicles as they travel down the highway.

Remember, if a terminal (metal) or the connector (plastic) is damaged, they should be replaced. DO NOT replace the complete wiring harness
assembly. Some harnesses are now on order restriction since most harness damage can be repaired.

Terminals and terminal removal tools are in the J 38125 Terminal Repair Kit and pigtails or complete connectors can be obtained through normal
parts ordering procedures OR from GMSPO and Saab PDC along with tape or conduit.

DisclaimerTechnical Service Bulletin # 06-08-45-004 Date: 060502

Electrical - Instrument Panel & General Wiring Repair


Bulletin No.: 06-08-45-004

Date: May 02, 2006


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 257
Chevrolet Venture V6-3.4L VIN E 2582

INFORMATION

Subject:
Instrument Panel (I/P), Body and General Wiring Harness Repair

Models:
2007 and Prior GM Cars and Trucks
2003-2007 HUMMER H2
2006-2007 HUMMER H3

Important:
A part restriction has been implemented on all Body and I/P harnesses and is being administered by the PQC. If a body or I/P harness
replacement is required, it can take 12-28 weeks for a harness to be built and delivered to a dealer. The dealer technician is expected to repair
any harness damage as the first and best choice before replacing a harness.

In an effort to standardize repair practices, General Motors is requiring that all wiring harnesses be repaired instead of replaced. If there is a
question concerning which connector and/or terminal you are working on, refer to the information in the appropriate Connector End Views in SI.
The Instruction Manual J 38125-620, which is sent with each new update of the J 38125 Terminal Repair Kit, also has terminal crimping and
terminal remove information.

Important:
There are some parts in the J 38125 Terminal Repair Kit (i.e. SIR connector CPAs and heat shrink tube (used in high heat area pigtail
replacement) and some TPAs that are not available from GMSPO. It is vitally important that each update to the J 38125 Terminal Repair Kit be
done as soon as it arrives at the dealer.

Utilize the Terminal Repair Kit (J 38125) to achieve an effective wiring repair. The Terminal Repair Kit has been an essential tool for all GM
Dealers since 1987. Replacement terminals and tools for this kit are available through SPX/Kent Moore. Refer to Corporate Bulletin Number
06-08-45-001 for more information.

The Instruction Manual J 38125-620, which is sent with each new update to the J 38125 Terminal Repair Kit, also has terminal crimping and
terminal removal information.

U.S. Dealers Only - Training courses (including Tech Assists, Emerging Issues, Web, IDL and Hands-on) are available through the GM Training
website. Refer to Resources and then Training Materials for a complete list of available courses.

Canadian Dealers Only - Refer to the Training section of GM infoNet for a complete list of available courses and a copy of the J 38125 Terminal
Repair Kit Instruction Manual.

Wiring repair information is also available in Service Information (SI). The Wiring Repair section contains information for the following types of
wiring repairs:

- Testing for intermittent conditions and poor conditions

- Flat wire repairs

- GMLAN wiring repairs

- High temperature wiring repairs

- Splicing copper wire using splice clips

- Splicing copper wire using splice sleeves

- Splicing twisted or shielded cable

- Splicing inline harness diodes

DisclaimerTechnical Service Bulletin # 00-01-38-001 Date: 000101

A/C - Lack of Performance in Hot/Humid Weather


BULLETIN NUMBER:
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 258
Chevrolet Venture V6-3.4L VIN E 2583
00-01-38-001

SECTION:
01 - HVAC

DATE:
January, 2000

TITLE:
HVAC Lack of Performance - Single A/C System Only (Evacuate & Recharge A/C System)

MODELS:
1998-2000 Chevrolet Venture
1998-2000 Oldsmobile Silhouette
1998-2000 Pontiac Trans Sport
With C60 Air Conditioner Frt, Manual Controls (Not C34)
Built from SOP thru VIN Breakpoint YD150489 for 2000 Models Only

CONDITION:
Some customers may comment on a lack of performance of the air conditioning system in hot, humid weather.

CAUSE:
This condition may be due to an undercharged air conditioning system during the vehicle assembly process.

CORRECTION:
1. Perform the Cooling Insufficient, A/C System check. Refer to the HVAC Systems-Manual sub-section of the Service Manual. If a condition
is identified, make the appropriate repair. If no abnormal condition is identified, proceed to the next step.

2. Evacuate and recharge the A/C system with 1.08 kg (2.375 lbs) of R-134a.

3. Replace the A/C evaporator label with P/N 10443319. This label will allow future service technicians to know how much refrigerant is
required by the system.

4. Inspect/test the A/C system for signs of leaks, both visually and with the A/C leak tester.

5. If a leak is found, perform the recommended repair. Refer to the HVAC Systems-Manual sub-section of the Service Manual.

6. If no leaks are found, perform the Cooling Insufficient, A/C System check. Refer to the HVAC Systems-Manual sub-section of the Service
Manual. If a condition is identified, make the appropriate repair. If no abnormal condition is identified, return the vehicle to the owner.

PARTS INFORMATION

Parts are currently available from GMSPO.

WARRANTY INFORMATION

For vehicles repaired under warranty, use chart:

*The 0.6 hr includes the time required to install the new label.

If an evacuate and recharge was required, add 0.9 hr to the base time for evacuating and recharging the HVAC System.

This is a unique Labor Operation Number for use only with this bulletin. This number will not be published in the Labor Time Guide.

Technical Service Bulletin # 00-01-38-007 Date: 000901

A/C Performance/Leaks - Diagnostic Procedure


File In Section: 01 - HVAC

Bulletin No.: 00-01-38-007

Date: September, 2000


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 259
Chevrolet Venture V6-3.4L VIN E 2584

Subject:
Correct Diagnostic Procedure When Reviewing A/C Performance Concern and A/C Refrigerant Leak is Suspected

Models:
1997-2001 Passenger Cars and Light Duty Trucks

This bulletin is being revised to update the text and model years. Please discard Corporate Bulletin Number 73-12-12A (Section 1 - HVAC).

Important:
The High Intensity Black Light, J 42220 or GM P/N 12377979, is the most up-to-date technology for finding extremely small leaks. Electronic
leak detectors which do not use the heated diode sensor technology should not be used.

The following diagnostic procedure should be used when a poor A/C performance concern is being investigated and an A/C refrigerant leak is
suspected:

1. Using the dealership's diagnostic computer, search the SI 2000 data base for bulletins applicable to the subject vehicle. A bulletin may have
been issued changing the amount of refrigerant the system should contain and outline proper repair procedures.

2. Start the vehicle's engine and switch the A/C control to the maximum cold position.

3. Inspect the A/C compressor clutch (is it engaged). If the compressor is mounted in a hard-to-see location, switch the A/C system OFF and
ON several times and listen for clutch engagement.

4. If the compressor clutch engages and stays engaged at idle, low side refrigerant pressure is sufficient to check for a leak.

5. To check for a leak, use Kent Moore Tool J 41459 for R134a and insert 1/4 oz of Kent Moore's J 41447 or GM P/N 12345303, R134a tracer
dye, into the refrigerant system.

Important:
By using this tool, the A/C refrigerant system does not have to be evacuated and/or opened just to insert the dye.

6. After insertion of the dye, spray a small amount of J 43872, fluorescent dye cleaner, around the low side fitting to remove any residue.

7. Observe and record on the repair order the ambient temperature and humidity as displayed on the ACR 2000, (J 43600) Air Conditioning
Recovery, Evacuation and Charging System.

8. Place a dial thermometer (ie. J 23640, or J 6742-03) in the center A/C outlet duct.

9. Start and run the engine at 1500 RPM for 5 minutes with the A/C system in the maximum cold position.

10. At the end of the 5 minute run time, record the temperature displayed on the thermometer on the repair order.

11. If the center outlet temperature is at least 11°C (20°F) cooler than the ambient temperature, the system is performing as designed.

12. Use Kent Moore Tool J 42220 or GM P/N 12377979, ultraviolet leak detection lamp, and inspect the complete system for evidence of a leak.

Important:
The leak dye mixes with the refrigerant lubrication (PAG oil). Therefore, extremely small leaks may be pressure, temperature or vibration
sensitive and may not be active during the 5 minute test above. In this case, it may be necessary to request the vehicle be returned for further
testing in 3 to 5 days. Vehicles which were driven in the rain, through sprinkler puddles, etc., may cause leak detection problems as the dye and
the PAG oil are both water soluble.

Warranty Information

For vehicles repaired under warranty, use:

Important:
This labor operation has been revised and the 12 month limitation has been removed. If a second test with the black light is needed within 10
days, the Service Manager's approval will be required prior to submission of the claim. If a subsequent leak is found, the test would be
considered part of the diagnostic time required for the repair.
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 260
Chevrolet Venture V6-3.4L VIN E 2585

DisclaimerTechnical Service Bulletin # 01-01-38-011 Date: 011001

A/C System - Proper Use to Achieve Maximum Cooling


File In Section: 01 - HVAC

Bulletin No.: 01-01-38-011

Date: October, 2001

INFORMATION

Subject:
Proper Use of HVAC System to Achieve Maximum Cooling

Models:
1997-2002 Chevrolet Venture
1997-2002 Oldsmobile Silhouette
1997-1998 Pontiac Trans Sport
1999-2002 Pontiac Montana

The following procedure should be explained to customers who come into the dealership expressing dissatisfaction with the operation of the HVAC
system during hot weather. This procedure will be in the next printing of the 2002 Owner's Manual as well as on an A/C Quick Reference card that
will be available soon.

In order to obtain maximum cooling from the vehicle's A/C system on very hot days, follow these steps:

1. Open the windows to allow some of the hot air to escape.

2. Press the A/C button (the indicator will illuminate) on the A/C control. Set the mode switch to OUTSIDE AIR (2).

3. Put the fan control on Speed 5 and set the temperature knob to full cold by turning it counterclockwise.

4. After 90 seconds, push the RECIRCULATION button (1) (the indicator will illuminate) and close the windows.

This procedure allows the A/C system to generate cold air while venting the hotter air that is inside the vehicle. Once the vehicle achieves the
desired comfort level, it is recommended you push the outside air button (the indicator will illuminate).

Important:
Operating the A/C system continuously in the recirculation mode can result in very low humidity in the passenger compartment. Passengers
may then experience discomfort due to dry eyes.

If the vehicle is equipped with the rear A/C option and there are rear passengers, put the rear fan control on Speed 3 until rear passenger comfort is
achieved. Once the desired comfort level is reached for the rear passengers, it is recommended that the rear blower speed be reduced. Setting the
rear blower speed to "R" will allow the rear passengers to control the rear blower speed and temperature setting. If there are no passengers in the
rear seats, front passenger comfort is achieved more rapidly by having the rear control set to "0" or OFF.
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 261
Chevrolet Venture V6-3.4L VIN E 2586

DisclaimerTechnical Service Bulletin # 99-01-39-007B Date: 030301

A/C - Automatic A/C Functional Description


File In Section: 01 - HVAC

Bulletin No.: 99-01-39-007B

Date: March, 2003

INFORMATION

Subject:
Automatic Air Conditioning Control Operation

Models:
1997-2003 Passenger Cars and Trucks
2003 HUMMER H2
with Automatic Air Conditioning

This bulletin is being revised to update the model years and add HUMMER. Please discard Corporate Bulletin Number 99-01-39-007A (Section 01
- HVAC).

Automatic air conditioning functional description:


Vehicles with automatic air conditioning (single and dual zone) have both automatic and manual operating systems.

For the system to operate automatically, the system controls must meet the following criteria:

1. The temperature setting must be one step warmer than the coldest allowable setting.

2. The temperature setting must be one step cooler than the warmest allowable setting.

3. The fan speed selector must be in the automatic position, no driver input to lower or raise the blower speed, after the auto button or key pad
has been pushed.

4. The air flow selector must be in the automatic position, no driver input to change the air flow output, after the auto button or key pad has
been pushed.

If these conditions are not met, the system is considered in the manual mode.

1. In the manual mode, all indicators of automatic operation (i.e. lights, messages, etc., depending on the vehicle car line) will be off.

2. Manual mode is when the driver air conditioning controls are in the full hot, full cold, non-automatic blower speed or non-automatic air
distribution control positions.

Do not replace air conditioning controls, as the system is functioning as designed.

DisclaimerTechnical Service Bulletin # 03-01-38-001 Date: 030301

A/C - System Sealers/Leak Detection Guidelines


File In Section: 01 - HVAC

Bulletin No.: 03-01-38-001


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 262
Chevrolet Venture V6-3.4L VIN E 2587

Date: March, 2003

INFORMATION

Subject:
A/C Refrigerant System Sealer and A/C System Leak Detection Guidelines

Models:
1994-2003 Passenger Cars and Trucks
2003 HUMMER H2
with Air Conditioning

It has come to the attention of GM Service Operations that A/C system sealers, A/C system stop-leak products, and A/C system seal conditioners
have become available to the consumer and A/C repair industry. GM Service Operations DOES NOT endorse or approve the use of any aftermarket
A/C system sealer, A/C stop-leak product or A/C seal conditioning product in any GM vehicle. The use of these aftermarket products may cause
damage to AC systems and to AC service equipment.

A/C systems found to be contaminated with A/C system sealers, A/C stop-leak products, or seal conditioners are not covered by the GM New
Vehicle Warranty or the GM Replacement Part Warranty.

GM Service Operations recommends the detection of A/C system leaks through the use of GM-approved leak detectors and fluorescent leak
detection dyes. GM recommends the replacement of leaking A/C components and the repair of leaking A/C connections. Many federal,
state/provincial and local regulations prohibit the recharge of A/C systems with known leaks.

Vehicles found or suspected to be contaminated by an A/C system sealer should be treated as a contaminated system. A/C system flushing may not
remove the system sealer from the system.

Using GM-approved (refrigerant-based) system flushing on A/C system contaminated with sealer products can introduce these sealer products to
A/C service equipment which may cause equipment damage. Unapproved system flushing methods can leave unacceptable amounts of flushing
agent in vehicle systems causing further damage. Component replacement may be necessary for correcting a vehicle system contaminated with
system sealer products. GM Service Operations recommends the use of only R-134a refrigerant for all vehicles manufactured since 1994. GM does
not recommend blended refrigerant or hydrocarbon-based refrigerant. GM Service Operations recommends only the application specific
compressor oil in the exact quantity specified for the application.

DisclaimerTechnical Service Bulletin # 01-01-39-003A Date: 030714

A/C - Catastrophic Compressor Failure Debris Removal


Bulletin No.: 01-01-39-003A

Date: July 14, 2003

INFORMATION

Subject:
J 44551 A/C Suction Screen Kit Repair Recommendations and Procedures After Catastrophic Compressor Failures

Models:
1997-2004 Passenger Cars and Light Duty Trucks
2003-2004 HUMMER H2
with Delphi HD6, HU6 and HT6 Compressors

Supercede:

This bulletin is being revised to update model years and add the HUMMER H2. Please discard Corporate Bulletin Number 01-01-39-003 (Section
01 - HVAC).

GM Service Operations and Delphi Thermal Systems have worked with GM dealers over the past three years to develop the tools and procedures to
increase your success rate on repairing vehicle A/C systems that experience catastrophic compressor failures.

After a catastrophic compressor failure, it is extremely important to eliminate and/or contain the debris that causes repeat repairs. The debris
generated from a catastrophic compressor failure is discharged into the compressor suction line, the discharge line, the condenser and the liquid
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 263
Chevrolet Venture V6-3.4L VIN E 2588
line. The use of the J 44551 Suction Screen Kit DOES NOT replace the need for liquid line filters as described in the vehicle specific Service
Manual. Liquid line filters should be used whenever possible (after a catastrophic compressor failure) to protect the expansion device (orifice tube
or TXV) from debris.

Analysis of failed replacement compressors show the debris discharged into the INLET side of the compressor (suction line) is often pulled into the
replacement compressor. It is important to keep this debris out of the new compressor to avoid repeat compressor failure. The J 44551 Suction
Screen Kit is designed to help protect the NEW (replacement) compressor from ingesting debris that was sent into the SUCTION side of the system
during a compressor failure.

The J 44551 kit supplies your dealership with the right tools and supplies to cover the Delphi HD6, HU6 and HT6 compressors for most GM
applications. Delphi V5 and V7 compressors already have this screen installed in the suction port of the compressor and do not need an additional
screen installed.

Service Procedure

Tools Required

J 44551 Suction Screen Kit

The J 44551 Suction Screen Kit contains three different screen sizes. It is important to select the correct size screen that will press fit into the
suction port of the compressor hose assembly. The screen should not be installed loose inside the hose assembly.

Installation Procedure

1. Evacuate the air conditioning system completely using the applicable recovery equipment.

2. Remove the bolt that attaches the manifold of the muffler assembly hose to the air conditioning compressor.

3. Use the Suction Port Sizing Tool (1) in order to determine the appropriate size filter screen.

4. Install the proper Installation Mandrel (1) on the threaded portion of the Installation Tool.

5. Using the Installation Tool, place the manifold into the fixture of the tool.

5.1. Lubricate the applicable filter screen with refrigerant lubricant.

5.2. Ensure that you are on the suction side of the air conditioning manifold.

5.3. Place the filter screen straight into the bore before proceeding.
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 264
Chevrolet Venture V6-3.4L VIN E 2589

5.4 Using a 9/16 in wrench, turn the bolt of the Installation Tool (3) clockwise, pressing the filter screen (2) into the bore.

The filter screen must be flush with or slightly below the bore.

6. Reinstall the manifold (1) on the rear of the air conditioning compressor. Make sure to tighten to the correct specifications.

Important:
Be sure to clean the appropriate surface before applying the Notification Label.

7. Included in the kit is a bright yellow Notification Label with the following message: ATTENTION! Suction Line Screen Installed. It is very
important that you apply this label to the manifold, the suction line, or some other appropriate, highly visible location.

Removal Procedure

1. Using the appropriate Removal Tool (1), place the Removal Tool (1) into the bore of the filter screen.

2. Turn the Removal Tool one turn clockwise, or until tight.

3. Turn the nut clockwise to remove the filter screen using the appropriate size wrench.

^ 11/16 in wrench for size A filter screen

^ 3/4 in wrench for size B filter screen

^ 7/8 in wrench for size C filter screen

DisclaimerTechnical Service Bulletin # 01-01-38-006D Date: 040901

A/C - R-134a System Flushing Procedures


File In Section: 01 - HVAC

Bulletin No.: 01-01-38-006D


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 265
Chevrolet Venture V6-3.4L VIN E 2590

Date: September, 2004

INFORMATION

Subject:
Contaminated R-134a A/C Systems - Air Conditioning System Flushing Procedures and Universal In-Line A/C Filter Installation

Models:
1993-2005 Passenger Cars and Light Duty Trucks

with Air Conditioning

This bulletin is being revised to update the parts information. Please discard Corporate Bulletin Number 01-01-38-006C (Section 01 - HVAC).

GM Service Operations has worked with GM dealers to develop tools and procedures to properly flush A/C (air conditioning) systems. The
recommended flushing procedure uses liquid R-134a refrigerant to perform the system flush and is the only GM approved method for system
flushing. The use of alternate methods that utilize solvents has proven to be detrimental to A/C system performance and durability. Every General
Motors dealer has received a J 43600 ACR 2000 Air Conditioning Service Center that has built-in A/C system flushing capabilities. Every General
Motors dealer has also received a J 45268 Flush Adapter Kit to utilize the flushing capability of the J 43600 ACR 2000.

This bulletin contains a general outline of the procedure and when to perform A/C system flushing. Vehicle specific flushing information is
contained in the HVAC section of SI.

A/C system flushing should NOT be routinely performed when a system failure is encountered. System flushing takes a considerable amount of
time to perform and is NOT necessary on most system failures. System flushing requires prior authorization by the GM Area Service Manager (the
District Service Manager in Canada) and should be performed only when one of the following conditions is found:

^ A desiccant bag failure.

^ A gross overcharge of A/C system lubricant.

^ The A/C system lubricant is contaminated.

^ A catastrophic compressor failure causing oil contamination.

A/C system flushing will remove some of the metal particles during a flush, but flushing is not completely effective in removing all metallic debris.
System flushing should not be considered if removal of metallic debris is the only objective. GM Service Operations continues to strongly
recommend the use of a Liquid Line Filter and a Suction Screen to control this type of system contamination and avoid repeat failures.

A/C System Flushing Procedure

Tools Required

^ J 43600 ACR 2000 Air Conditioning Service Center

^ J 45268 A/C Flush Adapter Kit J 41447 R-134a Tracer Dye or equivalent

^ J 41459 A/C Tracer Dye Injector or equivalent

^ J 42220 Universal 12V Leak Detection Lamp or equivalent

^ J 39400 Halogen Leak Detector or equivalent

^ J 44551 A/C Suction Screen Kit

^ J 45037 Oil Injector kit

^ J 45037-46 GM Universal Compressor PAG Oil (packaged as 6, 8 oz tubes)

A warm engine compartment or higher ambient temperatures as well as air flow across the heat exchangers (evaporator, accumulator and
condenser) speed the refrigerant recovery time during the A/C flush procedure. Whenever possible, warm the engine prior to A/C system flushing.
An external fan blowing across the condenser and running the A/C blower motor while the engine is running may be used to speed up refrigerant
recovery.

Front Only A/C Systems

1. Recover the refrigerant from the vehicle.

2. Remove the expansion device (orifice tube or TXV (Thermostatic Expansion Valve)).
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 266
Chevrolet Venture V6-3.4L VIN E 2591

3. Connect the A/C lines with the orifice tube removed or install the appropriate TXV Adapter from the J 45268 A/C Flush Adapter Kit.

4. Disconnect the A/C compressor manifold (never flush through a compressor).

5. Inspect the end of the suction hose for a suction screen. Remove the suction screen using the screen remover in the J 44551 A/C Suction
Screen Kit, if installed.

6. Install the appropriate A/C compressor hose assembly flush adapter(s) from kit J 45268.

7. Configure the flush adapter and hose for either a forward flush or reverse flush. Refer to the Flushing Configuration section of this bulletin.

Front/Rear (Dual Circuit) A/C Systems

Each circuit of a front/rear A/C system must be flushed separately. Flow to one circuit must be blocked with the use of a blocked orifice tube
or blocked TXV. The front circuit should always be flushed first.

Front Circuit

1. Recover the refrigerant from the vehicle.

2. Remove the expansion device (orifice tube or TXV) from the front circuit.

3. Re-connect the A/C lines with the orifice tube removed or install the appropriate non-blocked (open) TXV Adapter from kit J 45268.

Important:
A blocked orifice tube is not supplied with the J 45268 Adapter kit. A blocked orifice can be made as follows: Cut the orifice tube frame
and screen.

Remove enough of the frame and screen to access the end of the brass orifice tube. Seal the tube by pinching off the end of the orifice
tube.

4. Remove the expansion device (orifice tube or TXV) from the rear circuit and install a plugged expansion device (orifice tube or TXV) into
the rear circuit.

5. Disconnect the A/C compressor manifold.

6. Inspect the end of the suction hose for a suction screen. Remove the suction screen using the screen remover in the J 44551 A/C Suction
Screen Kit, if installed.

7. Install the appropriate A/C compressor hose assembly flush adapter(s) from kit J 45268.

8. Configure the flush adapter and hose for either a forward flush or a reverse flush. Refer to the Flushing Configuration section of this bulletin.

9. Perform the flush of the front system by following the instructions supplied with the J 43600 ACR 2000.

10. Replace the plugged expansion device (orifice tube or TXV) in the rear circuit with an open expansion device (orifice tube or TXV).

11. Replace the open expansion device (TXV or orifice tube) in the front circuit with a plugged expansion device (orifice tube or TXV).

12. Flush the rear system by following the instructions supplied with the J 43600 ACR 2000.

Flushing Configuration - Forward Flush

Forward flushing (the same flow as normal system operation) is recommended for contaminated refrigerant and/or A/C system lubricant.

Important:
Install a new filter inside the J 45268-1 for every flush. Service the filter with GM P/N 5651802 (use P/N 729832 in Canada). Remove
and discard the check valve from the filter.

Important:
Check that the J 43600 ACR 2000 has a sufficient refrigerant charge prior to the start of the flushing procedure. The J 43600 ACR 2000
must have at least 7 pounds (3.18 kgs) of refrigerant available for charging in the machine's internal storage vessel.

Important:
Always close the valve on the J 43600 ACR 2000 external refrigerant tank before starting the flushing procedure.

Follow these steps to perform the forward flush:

1. Connect the J 45268-1 flush filter adapter to the suction port of the A/C compressor hose assembly flush adapter.
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 267
Chevrolet Venture V6-3.4L VIN E 2592

2. Connect the blue hose from the J 43600 ACR 2000 to the J 45268-1 flush filter adapter.

3. Connect the red hose from the J 43600 ACR 2000 to the discharge port of the A/C compressor hose assembly flush adapter.

4. Follow the instructions supplied with the J 43600 ACR 2000 and flush the A/C system.

Flushing Configuration - Reverse Flush

Reverse flushing (the opposite flow of normal operation) is recommended for a desiccant bag failure. Always replace the accumulator after
the reverse flushing procedure is complete.

Important:
Install a new filter inside the J 45268-1 for every flush. Service the filter with P/N 5651802 (in Canada, P/N 729832). Remove and
discard the check valve from the filter.

Important:
Check that the J 43600 ACR 2000 has a sufficient charge prior to the start of the flushing procedure. The J 43600 ACR 2000 must have
at least 7 pounds (3.18 kgs) of refrigerant available in the machine's internal storage vessel.

Important:
Always close the valve on the J 43600 external refrigerant tank before starting the flushing procedure.

Follow these steps to perform the reverse flush:

1. Connect the J 45268-1 flush filter adapter to the discharge port of the A/C compressor hose assembly flush adapter.

2. Connect the blue hose from the J 45268-1 flush filter adapter.

3. Connect the red hose to the suction port of the A/C compressor hose assembly flush adapter.

4. Follow the instructions supplied with the J 43600 ACR 2000 and flush the A/C system.

After Flushing Is Complete

Important:
Flushing will remove all the A/C system lubricant and leak detection dye from the A/C system. After a catastrophic compressor failure, it
is extremely important to eliminate and/or contain the debris that may cause repeat repairs. The debris generated from a catastrophic
compressor failure will be discharged into the compressor suction line, discharge line, condenser and liquid line. The use of the J 44551
Suction Screen kit DOES NOT replace the need for liquid line filters as described in the vehicle specific Service Information. A liquid
line filter should be installed whenever possible, after a catastrophic compressor failure, to protect the expansion device (orifice tube or
TXV) in both the front and rear systems from debris.

The J 44551 supplies your dealership with the right tools and supplies to cover the Delphi HD6, HU6 and HT6 compressors, as well as most
non-Delphi compressors, for most GM applications. Delphi V5 and V7 compressors already have this screen installed in the suction port of
the compressor and do not need an additional screen installed.

The J 44551 Suction Screen Kit contains three different screen sizes. Additional screen sizes are being developed. It is important to select the
correct size screen that will press fit into the suction port of the compressor hose assembly. The screen should not be installed loose inside the
hose assembly.

1. Insert the J 44551-6 sizing tool into the suction hose to select the correct size suction screen.

2. Insert the suction screen into the compressor end of the suction hose.

3. Select and install the correct mandrel to the J 44551-5.

4. Install the J 44551-5 screen installation tool over the end of the suction hose and the suction screen.

Important:
Correct placement of the J 44551 is critical.

5. Tighten the forcing screw of the J 44551-5. The suction screen is fully installed when the screen is flush with the end of the suction hose
fitting.

6. Remove the J 44551-5 suction screen tool from the suction hose.

7. Install the J 44551-1 Suction Screen Notification Label.

8. Remove the A/C compressor.


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 268
Chevrolet Venture V6-3.4L VIN E 2593

9. Remove the A/C compressor drain plug, if equipped. Drain the A/C system lubricant from the compressor into a clean, graduated cylinder.
Rotate the compressor input shaft to assist in draining the A/C system lubricant from the compressor. Measure and record the amount of A/C
system lubricant removed.

10. Install the A/C compressor drain plug, if equipped.

11. Install the A/C compressor.

12. Remove the blocked orifice tube or TXV adapter (front/rear systems only).

13. Install a new orifice tube or remove the TXV adapter.

^ Inspect the original TXV for debris.

^ Clean or replace the original TXV as needed.

^ For front/rear systems, be sure both expansion devices (orifice tubes or TXVs) are installed.

Important:
Even after a system flush, control devices are subject to contamination and malfunction. To insure long term reliability the installation of
the newly redesigned in-line A/C filter before an orifice tube or rear TXV is recommended.

^ Install the in-line filter on front A/C systems before the orifice tube.

^ Install the in-line filter on front/rear A/C systems before the "Y" in the evaporator tube.

^ Do not allow metal burrs to enter the evaporator tube during cutting or when removing the burrs.

^ Because of limited space in the engine compartment, it may be necessary to remove the system's existing orifice tube and install the
orifice in the in-line filter.

14. Install a Universal In-line A/C Filter, P/N 89016656 (AC Delco P/N 15-10413). Refer to the instruction sheet included with the filter for
detailed installation instructions. Re-install the suction screen if it was previously removed.

15. Look up the required amount of A/C system lubricant for the vehicle being worked on. Refer to the System Capacities table in the
appropriate section of SI. Remember that after a system flush there is no lubricant in the A/C system.

16. Install the proper amount of Synthetic Lubricant (Universal Refrigerant Oil), P/N 12378526 (in Canada, P/N 88900060), into the A/C system
using the J 45037 Oil Injector.

17. Add one bottle of J 41447 R-134a Tracer Dye, GM P/N 12346303 (in Canada, P/N 10953458), or the equivalent, using the J 41459 dye
injector (or the equivalent).

18. Evacuate the A/C system.

19. Recharge the A/C system to the proper charge level specified for that vehicle's A/C system.

20. Verify proper A/C system operation.

21. Leak test all connections using the J 44220 Universal 12V Leak Detection Lamp, the J 39400-A Leak Detector or equivalents. Remember
that the A/C system must operate for several minutes before leak dye will show a leak if one is present.
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 269
Chevrolet Venture V6-3.4L VIN E 2594

Parts Information

Warranty Information

GM has not established a specific labor operation for system flushing. When system flushing is necessary during the warranty period, submit
additional labor hours with the labor operation used for the system repair.

DisclaimerTechnical Service Bulletin # 01-02-32-004 Date: 010401

Special Tools - Power Steering System Analyzer


File In Section: 02 - Steering

Bulletin No.: 01-02-32-004

Date: April, 2001

INFORMATION

Subject:
Guidelines For Use of Essential Tool J 44721 Power Steering System Analyzer

Models:
1997-2002 Passenger Cars and Light Duty Trucks with Power Steering

Every General Motors dealer has received a power steering pressure and flow analyzer J 44721, or update kit J 44721-upd. This bulletin is being
sent to help answer questions regarding the use of the J 44721 analyzer and inform service personnel of the additional diagnosis time for the
installation and use of the analyzer.

Over the last year, GM Product Engineering and Delphi Steering Systems have worked with select GM dealers using this tool to properly diagnose
and correct conditions with power steering gears and pumps. The results of this cooperative effort show a significant decrease in unnecessary pump
and gear replacement. This new tool gives the GM dealer a competitive advantage in the area of power steering repair and will help GM technicians
to fix vehicles "right the first time."

The J 44721 Power Steering Analyzer is intended to aid diagnosis of power steering Systems and is very easy to use. The technician can use this
tool to eliminate the hydraulic portion of the power steering system as the cause of specific customer concerns. Use tool J 44721 and Service
Manual diagnostics for the following concerns:

^ Excessive effort required when turning

^ Too little effort required when turning


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 270
Chevrolet Venture V6-3.4L VIN E 2595

^ Noise conditions that may be related to the hydraulic system (i.e. pump whine/laboring)

Important:
If the diagnosis indicates pump and/or steering gear meet the published pressure and flow specifications, do not arbitrarily replace either
component. Refer to published Service Information such as SI2000 or Service Bulletins for further diagnosis.

Do not use tool J 44721 for the following concerns:

^ known power steering concerns currently addressed by published Service Bulletins

^ Power steering system external leaks

^ Mechanical (non-hydraulic) noise conditions (shudder, rattle, etc.)

Use the tool by installing the J 44721 analyzer in series on the pressure side of the hydraulic power steering system. Use the adapters included in
the kit and install the J 44721 on the most accessible pressure fitting. Any location on the pressure side of the system is acceptable such as:

^ Power steering pump outlet at the power steering pump

^ Power steering pressure line at the steering gear

^ Power steering pressure line at the hydroboost booster (if applicable)

Refer to the appropriate vehicle Service Manual and perform the power steering system test procedure. You may claim 0.0 to 0.5 hours of diagnosis
time, depending on actual time spent performing diagnosis. Additional labor time for the use of J 44721 can be submitted for the labor operations as
shown.

The use of additional labor time is subject to review and the guidelines given in this bulletin.

U.S. Dealers

A power steering system training video was previously provided to all GM dealers to help technicians in diagnosing steering system concerns. GM
recommends all dealership steering/suspension technicians review this video. Additional copies of this video can be obtained by contacting
Kent-Moore Tools at 1-800-GM TOOLS and requesting J 44721-VID.

DISCLAIMER
Technical Service Bulletin # 02-06-01-026 Date: 020601

Engine - Identification Information


File In Section: 06 - Engine/Propulsion System

Bulletin No.: 02-06-01-026

Date: June, 2002

INFORMATION

Subject:
Engine Identification Information

Models:
2003 and Prior Passenger Cars and Trucks
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 271
Chevrolet Venture V6-3.4L VIN E 2596
2003 HUMMER H2
with North American Engines

This bulletin covers the location of the engine identification information for OEM, service, Goodwrench(R) and remanufactured engines. The OEM
information is a paper bar code tag attached to the engine. The Goodwrench(R) information is on a metal tag attached to the engine.

OEM Identification Information

The engine bar code tag is usually in one of several places. The bar code tag could be on a rocker arm cover, the ends of a cylinder head or on the
oil pan or the oil rail area of the engine. The information required from the tag is the 3 position alpha-numeric code which identifies the model of
the engine and the series of numbers at the bottom of the tag. The number of digits will vary depending on the engine application. All the numbers
will be required to process an engine request. If this is the original engine in the vehicle, the engine information is available in GMVIS. Choose the
Vehicle Component selection, the 3 position alpha-numeric code is the Part/Num Broadcast section and the Traceability section is the bar code
information that is required. It may be easier to use GMVIS to obtain the necessary information; however, it is only valid for the original engine.
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 272
Chevrolet Venture V6-3.4L VIN E 2597
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 273
Chevrolet Venture V6-3.4L VIN E 2598

Engine ID Tag locations

6 Cylinder Engine Locations

^ L36 and L67 applications - Center of the LH rocker arm or LH side of the engine in the oil pan rail area of the engine

^ LX5 applications - Front end of the LH rocker cover

^ L35 and LU3 applications - Front of the RH cylinder head or right side of the oil pan sump

^ LA1 and LG8 applications - Top of the RH rocker arm cover or front of RH oil pan rail

^ L81 and LA3 applications - On cam drive cover on the front of the engine

^ LL8 applications - Rear of rocker arm cover on the front of oil pan rail on the RH side

V8 Engine Locations

^ LR4, LM7, LQ4 and LQ9 applications - Rear of RH cylinder head or RH side of the oil pan

^ LS1 and LS6 applications - Rear of LH cylinder head or the front part of LH oil pan rail
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 274
Chevrolet Venture V6-3.4L VIN E 2599

^ L30 and L31 applications - Rear of RH rocker cover or on the RH side of the oil pan

^ L46, L37 and LD8 applications - Front of RH rocker cover or the RH side of oil pan rail

4 Cylinder Engine Locations

^ L61 applications - Front of the rocker cover

^ LN2 and L43 applications - Top of the rocker arm cover

^ LD9 applications - Top of the timing chain cover

Goodwrench(R) and Remanufactured Engine ID Tags

The tag is made of metal and is approximately 2 in x 1-11/16 in (5.1 cm X 4.3 cm). It is installed on all remanufactured engines and new engines
assembled by non-GM suppliers.

DisclaimerTechnical Service Bulletin # 02-06-01-028 Date: 020801

Engine - Crankcase Flushing Recommendations


File In Section: 06 - Engine/Propulsion System

Bulletin No.: 02-06-01-028

Date: August, 2002

INFORMATION

Subject:
Engine Crankcase Flush
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 275
Chevrolet Venture V6-3.4L VIN E 2600

Models:
2003 and Prior GM Cars and Trucks
2003 HUMMER H2
2003 and Prior Isuzu Light and Medium Duty Trucks with Gasoline Engines

General Motors is aware that some companies are marketing tools and equipment to support engine crankcase flush procedures. GM does NOT
endorse or recommend crankcase flushing for any of its gasoline engines. Analysis of some of the materials used for crankcase flushing procedures
indicate incompatibility with GM engine components and the potential for damage to some engine seals and bearings. Damage to engine
components resulting from crankcase flushing procedures is not covered under the terms of the New Vehicle Warranty.

DISCLAIMERTechnical Service Bulletin # 01-01-38-013A Date: 031029

A/C - Unnecessary Compressor Replacement


Bulletin No.: 01-01-38-013A

Date: October 29, 2003

INFORMATION

Subject:

Diagnostic Information To Consider Before Air Conditioning Compressor Replacement

Models:
1993-2004 Passenger Cars and Light Duty Trucks

Supercede:

This bulletin is being revised to add the 2004 model year and add information for clarification. Please discard Corporate Bulletin Number
01-01-38-013 (Section 01 - HVAC).

A recently completed analysis of air conditioning (A/C) compressors that had been replaced for noise, vibration and insufficient cooling concerns
has indicated a high number of "no trouble found" results. Further studies have shown that the root cause of the customer concerns that might lead
to a compressor replacement was often a state of refrigerant charge issue or in another area or system of the vehicle. The A/C system refrigerant
charge level, either high or low, has been found to be a major contributor to unnecessary compressor replacement. The ability of the ACR 2000
Refrigerant Recycling/Recharging Tool to recover and measure the weight of the A/C system refrigerant charge will help the technician make a
more accurate diagnosis of a charge level concern prior to any component replacement.

A thorough visual inspection should always be performed before any tests or repairs are done. Doing so may find an obvious problem that will save
time and eliminate the need for extensive diagnosis. Some additional items, as listed below, should be considered before a compressor is replaced
for noise, vibration or insufficient cooling concerns.

^ The compressor mounting bolts, brackets or braces may be loose or missing.

^ The compressor drive belt may be frayed, loose or misaligned.

^ The A/C refrigerant lines may be grounding out on body, chassis or engine components. This may allow noise and vibration to be transmitted
into the passenger compartment.

^ The air flow through the condenser may be insufficient.

- The condenser fins may be bent or filled with debris.

- The space between the condenser and radiator may be filled with leaves or debris.

- The cooling fans may be inoperative or not performing as designed.

- The installation of aftermarket accessories may alter or restrict the air flow through the condenser.

^ Inspect for missing or mispositioned air deflectors, baffles, seals and shrouds.
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 276
Chevrolet Venture V6-3.4L VIN E 2601

^ The compressor cycling switch may not be operating correctly. This may allow the evaporator core to freeze up or the compressor may not stay
engaged long enough for proper system pressures to develop.

^ The air flow through the evaporator core may be restricted.

- The cabin filter may be plugged.

- The evaporator core may be covered with debris.

- The cowl air inlet leaf screen may by plugged.

^ The A/C system may be overcharged or undercharged with refrigerant. The A/C system charge weight can be measured with the ACR 2000
after a refrigerant recovery is done.

^ The A/C system may have an improper amount or incorrect type of refrigerant oil. Only GM approved refrigerant oils should be used.

^ An A/C system sealer is not approved for use in GM vehicles.

^ The vehicle's refrigerant may be contaminated or contain an excessive amount of air. The vehicle's A/C system may have been charged with an
unapproved refrigerant. The refrigerant identifier on the ACR 2000 should alert the technician to these conditions.

^ The orifice tube or thermostatic expansion valve (TXV) may be restricted, plugged or inoperative.

^ The capillary bulb on the TXV must be properly positioned so that the valve will provide proper refrigerant flow.

^ The desiccant bag in the accumulator may have failed, allowing debris to circulate in the A/C system.

^ The A/C system charge weight may have been changed. Components with an updated design may have been released. A check for service
bulletins applicable to the vehicle being worked on should always be done.

^ A check for diagnostic trouble codes in all the control modules on the vehicle should be done. Some trouble codes will disable compressor
operation after they have set. They must be repaired and cleared before compressor operation is allowed.

^ Verify that the engine is not operating with a low unstable idle, and that the engine is operating within the compressor engagement parameters
(for example; the engine may be overheating or it may be too cold for compressor engagement).

^ The diagnostic procedures in the HVAC section of the Service Manual should be performed as written to prevent the misdiagnosis of a
customer concern. The HVAC Diagnostic System Check and the A/C System Performance Test are written for a specific model only. They are
not generic charts. They follow a logical order with detailed instructions on how to perform each step.

^ The Technical Assistance Center may be contacted for additional help and the latest information on any unusual concerns.

When a thorough HVAC system diagnosis indicates that the compressor should be replaced, follow the procedure in the appropriate Service
Manual. The oil balance instructions are an important part of the replacement procedure. The correct refrigerant oil, as listed in the Service Manual,
must be used in the new compressor. It is recommended that a suction screen filter be installed on Delphi Harrison compressors that do not already
have one. The suction screen filter is not approved for use on compressors from other manufacturers. Refer to Corporate Bulletin Number
01-01-39-003A for more information on A/C suction screen kit repair recommendations and procedures. If the compressor has had a catastrophic
internal failure, an inline filter may be required to capture the large amount of debris that may be found to be circulating in the A/C system. In
addition, the A/C system may require flushing. Refer to Corporate Bulletin Number 01-01-38-006B for more information on flushing procedures
and recommendations.

The addition of fluorescent refrigerant leak dye to the A/C system is recommended if the vehicle does not have it installed already. Some vehicles
have leak dye installed at the assembly plant and this will be indicated on the A/C charge label. Refer to Corporate Bulletin Number 00-01-38-009B
for more information. If leak dye has been added during a previous repair and has been in the vehicle for more than three years, it is recommended
that additional dye be added. Finally, a leak check of the entire A/C system should be performed before the vehicle is returned to the customer.

Important:
For all GM paid repairs, the charge summary printout from the ACR 2000 is still required to be attached to the shop copy of the repair order.
The warranty code must be submitted in the warranty claim information in the comment field. This code provides valuable information about
the repair to General Motors for product quality improvement.

DisclaimerTechnical Service Bulletin # 03-06-01-002 Date: 030201


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 277
Chevrolet Venture V6-3.4L VIN E 2602

Engine - New Polymer Coated Piston and Rod Assembly


File In Section: 06 - Engine/Propulsion System

Bulletin No.: 03-06-01-002

Date: February, 2003

INFORMATION

Subject:
New Polymer Coated Piston and Rod Assembly

Models:
2000-2003 Buick Century
2002-2003 Buick Rendezvous
1996 Chevrolet Lumina APV
1997-2003 Chevrolet Venture
1999-2001 Chevrolet Lumina
1999-2003 Chevrolet Malibu, Monte Carlo
2000-2003 Chevrolet Impala
1996-2003 Oldsmobile Silhouette
1999 Oldsmobile Cutlass
1999-2003 Oldsmobile Alero
1996-1999 Pontiac Trans Sport
1999-2003 Pontiac Grand Am
2000-2003 Pontiac Grand Prix, Montana
2001-2003 Pontiac Aztek
with 3.1L or 3.4L V-6 Engine (VINs E, J - RPOs LA1, LG8)

A new piston and rod assembly has been released for use in the above models. The new piston is Polymer coated and will arrive with the piston
rings and connecting rod already assembled to it, but does not contain the connecting rod bearing. Use this new piston assembly any time the need
to replace either the piston or connecting rod should arise.

The new piston assembly part numbers are shown.

Parts are expected to be available from GMSPO February 17, 2003.

DisclaimerTechnical Service Bulletin # 05-06-02-007 Date: 050602

Cooling System - Revised Thermostat Replacement


Bulletin No.: 05-06-02-007

Date: June 02, 2005

SERVICE MANUAL UPDATE

Subject:
SMU - Revised Thermostat Replacement Procedure

Models:
1997-2005 Chevrolet Venture
1997-2004 Oldsmobile Silhouette
1997-1998 Pontiac Trans Sport
1998-2005 Pontiac Montana

This bulletin is being issued to revise the Thermostat Replacement procedure in the Engine Cooling sub-section of the Service Manual. Please
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 278
Chevrolet Venture V6-3.4L VIN E 2603
replace the current information in the Service Manual with the following information.

The following information has been updated within SI. If you are using a paper version of this Service Manual, please make a reference to this
bulletin on the affected page.

This procedure previously stated that it was necessary to remove the exhaust crossover pipe. This step is NOT required.

DisclaimerTechnical Service Bulletin # 99-06-02-017 Date: 991001

Cooling - Radiator Repair/Replacement Guidelines


File In Section: 06 - Engine/Propulsion System

Bulletin No.: 99-06-02-017

Date: October, 1999

INFORMATION

Subject:
Radiator Repair/Replacement Guidelines

Models:
2000 and Prior Passenger Cars and Trucks

If repair of an aluminum/plastic radiator is required, it is recommended that the following guidelines be followed:

For Vehicles Under Warranty

For aluminum/plastic radiators that have damage to the face of the core including bent fins, punctures, cuts, leaking tubes or header tubes, the
aluminum radiator core section should be replaced with a new one. In these cases, if both of the plastic tanks are not damaged, they can be reused
with the new core. If one or both of the plastic tanks are damaged along with the core, it is recommended that a complete new radiator assembly be
installed.

Warranty repairs for leaks at the tank to header (gasket leaks), broken/cracked plastic tanks, cross threaded or leaking oil coolers should be repaired
without replacing the complete radiator. This type of repair should be handled by the radiator repair facility in your area.

Many of these radiator repair facilities are members of the National Automotive Radiator Service Association (NARSA) who follow industry and
General Motors guidelines when repairing radiators. These facilities have the special tools, tanks and pressurizing equipment needed to properly
test the repaired radiator prior to returning it to the dealership. Many of these facilities receive the repair components directly from General Motors.

The sublet expense for a new radiator or the repair of the radiator under warranty should be handled following normal procedures.

For Vehicles No Longer Under Warranty

The GM released epoxy repair kit referenced in previous publications is no longer available. Repairs to the radiator, rather than replacement, is
strictly at the owner's discretion.Technical Service Bulletin # 99-03-10-104 Date: 991101

Tires - Improper/Recommended Tire Pressure


File In Section: 03 - Suspension

Bulletin No.: 99-03-10-104

Date: November, 1999

INFORMATION

Subject:
Improper Tire Pressure

Models:
1999-2OOO Passenger Cars and Trucks
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 279
Chevrolet Venture V6-3.4L VIN E 2604

Important:
Tires must be set to the recommended inflation pressure during the pre-delivery inspection (including the spare tire).

Ride, handling and road noise concerns may be caused by improperly adjusted tire pressure. The first step in diagnosis of these concerns is to verify
that the tires are inflated to the correct pressures. The recommended tire inflation pressure is listed on the vehicle's tire placard. The tire placard is
located on the driver's door edge or the rear compartment lid. Do not use the tire pressure indicated on the tire itself as a guide. Always inspect and
adjust the pressure when the tires are cold. Vehicles that have different pressures for the front and the rear need to be adjusted after tire rotation.

Improper tire inflation may result in any or all of the following conditions:

^ Premature tire wear

^ Harsh ride

^ Excessive road noise

^ Poor handling

^ Reduced fuel economy


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 280
Chevrolet Venture V6-3.4L VIN E 2605

2000 GM RECOMMENDED TIRE INFLATION


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 281
Chevrolet Venture V6-3.4L VIN E 2606

1999 GM RECOMMENDED TIRE INFLATION Technical Service Bulletin # 00-03-10-003B Date: 010501

Tires - Bumper To Bumper Warranty Coverage


File In Section: 03 - Suspension

Bulletin No.: 00-03-10-003B

Date: May, 2001

WARRANTY ADMINISTRATION

Subject:
GM Tire Warranty for Bumper-to-Bumper Program

Models:
1996-2001 Passenger Cars and Light Duty Trucks

Attention:
"GM of Canada" and "IPC" dealers are not authorized to utilize this service bulletin.

This bulletin is being revised to include information on the new GM Global Tire Warranty & Claims (GTWC) website for preparing the GM Tire
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 282
Chevrolet Venture V6-3.4L VIN E 2607
Requisition & Return Document for tires being replaced under the Bumper-to-Bumper New Vehicle Limited Warranty Program. Please discard
Corporate Bulletin Number 00-03-10-003A (Section 03 - Suspension)

Since the 1996 model year, original equipment manufactured (OEM) tires on all GM passenger cars and light duty trucks are covered under the
Bumper-to-Bumper time and mileage provisions of the GM New Vehicle Limited Warranty. Saturn began such coverage with the 2001 model year.
Tire warranty coverage allows the customer to have all warranty needs, including tires, addressed at one location - a GM dealership. Although GM
dealers are not required to inventory tires to administer this warranty coverage, some dealers may choose to do so.

What Is Covered

Only OEM tires are covered against defects in material and workmanship. OEM tires will always have a Tire Performance Criteria (TPC) number
molded on the sidewall near the tire size. (Exceptions: Prizm and some Tracker models do not use TPC tires, but are still covered.) Any replaced
tire will continue to be covered for the remaining portion of the New Vehicle Warranty. Tires will be warranted without prorated charges for tread
mileage.

Following expiration of GM's coverage, tires may continue to be warranted, on a pro-rated basis, by the tire manufacturer. Review the tire
manufacturer's booklet (included as part of the glove box material).

What Is Not Covered

^ Non-original equipment tires (those without a TPC number molded on the sidewall except Prizm and Tracker) are not covered.

^ Normal tire wear and wear out is not covered.

^ Road hazard is not covered. This includes punctures, cuts, impact breaks, etc.

Road hazard is covered by the tire manufacturer on sealant and EMT (run flat) tires.

^ Damage due to misuse, negligence, lack of maintenance, alteration, racing and vandalism is not covered.

Global Tire Warranty & Claims Website

Effective May 14, 2001, GM dealers will be required to use the Global Tire Warranty & Claims (GTWC) website to electronically initiate the Tire
Requisition & Return Document needed to obtain replacement tires. All previous paper copy versions of this document should be discarded.

The GTWC website is a secured, encrypted, password-protected tool designed to allow GM to collect and monitor data on tires being replaced on
all GM vehicles, providing an early warning for any concerns. The website will provide a more efficient, faster and error-free procedure for
preparing the GM Tire Requisition & Return Document.

The electronic Tire Requisition & Return Document requires one form per tire, not one form per vehicle, as in the past. This web form is designed
to automatically fill data fields and provides many drop-down menu selections to minimize user effort. It also has additional data requirements on
types of adjustments and has a monitoring system for the return of tires to the tire manufacturer for inspection. GM dealers will need to print copies
of the completed web form to get replacement tires from the local tire dealer and to return the removed tire(s) to the tire manufacturer for
inspection.

Once the removed tire has been returned and inspected, the tire manufacturer will also use the GTWC web system to complete the form initiated by
the GM dealer.

Initiating a Tire Requisition & Return Document Online

Users may access the system using any PC with an Internet connection through the GM ACCESS hyperlink or preferably using a local Internet
Service Provider (ISP). The minimum browser version required is Netscape 4.5 or Internet Explorer 4.0 or higher. The GM ACCESS server has an
outdated web browser and cannot be used to access this website. Please use a client PC with the appropriate level of browser.

1. From a Microsoft Internet Explorer or Netscape, type in the web address: http://gtwc.gm.com.

2. IN the pop-up logon window, type your User ID (which is your Business Association Code) and your password (your initial password is the
same as your User ID) and then click the OK button.

3. For security, each dealer is encouraged to change their password after they logon the first time. Click on "Change Password" from the upper
right-hand menu bar and follow the instructions provided. Please note that User IDs and passwords are case sensitive.

4. From the "Create New Adjustment" screen, select your GM Dealer Code from the drop-down menu.

5. Proceed through the form, using the drop-down menus and "populate" buttons to auto-fill related data.

6. Help buttons are located at individual data fields and overall forms help and definitions are available at the top right of the screen.

7. From the bottom of the screen, you can "Save as Draft" to complete the form later or "Submit" the form if it is complete.
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 283
Chevrolet Venture V6-3.4L VIN E 2608

8. A confirmation screen will appear allowing you to print the form. Three copies of the form should be printed. One copy will be provided to
the tire store to obtain a replacement tire. The second copy will be sent with the returned tire and the third copy should be retained. in the
vehicle history file. In addition, an option to quickly create another form called "Next Tire Same Vehicle" is shown.

9. On the navigation menu bar across the top of the screen, "Edit" and "View" choices provide a way to get back to incomplete forms or view
forms that have been submitted. A search mechanism is available to sort through forms by fields (date of form, repair order number, etc.).

U.S. help Line for GTWC Website Users:


1-888-337-1010
Follow prompt 3: For GM ACCESS, DealerWorld and Other Internet Applications

Obtaining New Tires

1. Determine the vehicle and tire eligibility based on the What Is Covered/What Is Not Covered portion of this bulletin.

2. A GM Tire Requisition and Return Document must be completed electronically on the website to obtain tires. Pressing the web form Submit"
button does NOT order a new tire. GM dealers will need to print a copy of the completed web form to get the replacement tire from the local
tire dealer.

3. New tires are to be obtained through the local tire dealer using a printed copy of the GM Tire Requisition and Return web form. A warranty
replacement tire will be provided at no charge. Dealers are NOT to purchase warranty replacement tires. If a tire dealer is not convenient, call
the tire manufacturer's toll-free phone number (listed later in this bulletin). Some tire companies will ship direct to the GM dealership.

4. New tires should be properly mounted, dynamically balanced and installed in the customer's vehicle. Proper balance weights and wheel nut
torque procedures must be used.

Returning Old Tires

MOST tires replaced under the New Vehicle Limited Bumper-to-Bumper Warranty will be returned to the tire manufacturer. This is done using
pre-addressed, prepaid UPS shipping labels. These labels can be obtained from Helm by calling 1-888-549-6152. Do NOT call UPS or the tire
companies for these labels. There will be instances when the GM Warranty Parts Center (WPC) will request tires. Therefore, all replaced tires must
be retained until receipt of claim payment. The WPC will request a tire(s) on the same day the credit memo is received at the GM dealership. If no
WPC request is received, the dealer should return tires to the proper tire manufacturer.

GM dealers are encouraged to submit warranty claims as soon as possible in order to alleviate storage of tires.

Whether returned to the tire manufacturer or the WPC, a printed copy of the Tire Requisition and Return Document web form and the repair order
must be placed in an envelope and securely taped to EACH tire being returned. A shipping label to the WPC or tire company must be attached to
EACH tire being returned. Using a tire crayon, mark the tire to indicate the reason for replacement or location of the defect.

Submitting a Warranty Claim

1. The correct tire warranty labor code must be used for the brand of tire replaced. Choose the correct labor code from the list as shown.

2. The generic number 09592318 MUST be inserted on all tire claims in the "part number" field regardless of manufacturer to ensure correct
processing.

3. A $25 administrative allowance per repair order MUST be inserted in the "parts amount" field.

4. Labor for mounting and balancing should be submitted.

5. Freight charges for tire returns are NOT to be submitted.

Labor time to replace one tire, including mounting and balancing, is 0.6 hr. Each additional tire replaced is 0.4 hr.

Important:
For tire replacement because of transportation damage or incorrect parts, use labor code E0421 and submit as a transportation claim.
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 284
Chevrolet Venture V6-3.4L VIN E 2609

Tire Company Assistance

DISCLAIMER

Technical Service Bulletin # 01-03-10-011 Date: 011201

Tires - Sidewall Damage


File In Section: 03 Suspension

Bulletin No.: 01-03-10-011

Date: December, 2001

INFORMATION

Subject:
Tire Sidewall Damage

Models:
2002 and Prior Passenger Cars and Light Duty Trucks

Inspection of a number of tires returned to the Warranty Parts Center and the various tire manufacturers has revealed gouges and/or abrasions that
are located on the tire's outboard sidewall. Typically, these gouges and/or abrasions appear to be located near where the tire was marked for wheel
balance weight installation at the vehicle assembly plant.

It has been determined that this type of surface damage to the tire may be the result of dealers or owners using a high pressure power washer to
remove wax/paint/ink marks from the tire sidewall. Do not use a high pressure power washer on tires. To remove any markings from the tire's
sidewall, only use soap water and a scrub brush.

This type of tire sidewall damage should not be considered as a warrantable condition.

DISCLAIMERTechnical Service Bulletin # 99-03-10-103 Date: 991001

Wheels - Stud Removal Tool Change


File In Section: 03 - Suspension

Bulletin No.: 99-03-10-103

Date: October, 1999

INFORMATION

Subject:
Discontinue Usage of Tool J 6627-A for Wheel Stud Removal
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 285
Chevrolet Venture V6-3.4L VIN E 2610

Models:
1992-99 Buick Riviera
1992-2000 Buick Century, LeSabre, Park Avenue, Regal
1992-2000 Cadillac DeVille, Eldorado, Seville
1992-96 Chevrolet Lumina APV
1997 Chevrolet Corvette (C-5)
1997-2000 Chevrolet Venture
2000 Chevrolet Impala, Monte Carlo
1992-99 Oldsmobile Aurora, Eighty Eight, Regency
1992-2000 Oldsmobile Silhouette
1998-2000 Oldsmobile Intrigue
1992-98 Pontiac Trans Sport
1992-2000 Pontiac Bonneville, Grand Prix
1999-2000 Pontiac Montana

SPECIAL TOOL J 6627-A IS NOT TO BE USED AS THE WHEEL STUD REMOVAL TOOL FOR THE ABOVE VEHICLES.

Notice:
The fingers of J 6627-A extend too far down the back of the wheel hub and bearing assembly. When this tool is used as a wheel stud press, it
may cause damage to the wheel hub inner seal. If the seal is damaged, water intrusion may occur and the life span of the wheel hub and bearing
assembly may be decreased.

Important:
If any seal is damaged, it is recommended that the wheel hub and bearing assembly be replaced.

USE OF EITHER SPECIAL TOOL J 35917 OR J 43631 IS RECOMMENDED IN ORDER TO PROPERLY REMOVE THE WHEEL STUDS
ON THE VEHICLES LISTED ABOVE.

These tools have similar dimensions and differ slightly in appearance, therefore, only one illustration is included.

Notice:
Do not remove the wheel studs with a hammer. This technique can potentially damage the wheel hub and bearing assembly.

In addition to using special tool J 35917 or J 43631, the following vehicles require the front wheel hub bearing to be removed from the front
aluminum knuckle in order to replace the wheel stud:

- 1995-99 Buick Riviera

- 1997-2000 Buick Century, Park Avenue Regal

- 2000 Buick LeSabre

- 1997-2000 Cadillac DeVille, Eldorado, Seville

- 1997 Chevrolet Corvette (C-S)

- 1997-2000 Chevrolet Venture


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 286
Chevrolet Venture V6-3.4L VIN E 2611

- 2000 Chevrolet Impala, Monte Carlo

- 1995-99 Oldsmobile Aurora

- 1997-2000 Oldsmobile Silhouette

- 1998-2000 Oldsmobile Intrigue

- 1997-98 Pontiac Trans Sport

- 1997-2000 Pontiac Grand Prix

- 1999-2000 Pontiac Montana

- 2000 Pontiac BonnevilleTechnical Service Bulletin # 01-03-10-009A Date: 040727

Wheels - Plastic Wheel Nut Covers Loose/Missing


Bulletin No.: 01-03-10-009A

Date: July 27, 2004

TECHNICAL

Subject:
Plastic Wheel Nut Covers Missing and/or Loose (Replace Missing Covers and Add Sealant to All Covers)

Models:
2005 and All Prior Passenger Cars (Except All Cadillac Models and Pontiac GTO)

with Plastic Wheel Nut Covers

Supercede:

This bulletin is being revised to add additional models years. Please discard Corporate Bulletin Number 01-03-10-009.

Condition

Some customers may comment that the plastic wheel nut covers are missing and/or loose.

Correction

Important:
^ DO NOT USE a silicone-based adhesive.

^ Do not apply the *permatex(R) around the threads in a circular pattern.

^ Apply a single bead across the threads approximately 10 mm (0.4 in) in length, 5 mm (0.2 in) in height and 5 mm (0.2 in) in width.

Replace any missing plastic wheel nut covers with the appropriate covers and apply Permatex(R) # 2 Form A Gasket Sealant(R) to the threads of all
the plastic wheel nut covers. Tighten finger tight plus a 1/4 turn with a hand wrench.

*We believe this source and their products to be reliable. There may be additional manufacturers of such material.

General Motors does not endorse, indicate any preference for or assume any responsibility for the products from this firm or for any other such
items which may be available from other sources.

Permatex(R) # 2 Form A Gasket Sealant(R) part numbers (available at your local parts supplier)

^ P/N 80009 (2A/2AR) - 44 ml (1.5 oz) tube boxed


^ P/N 80015 (2AR) - 44 ml (1.5 oz) tube carded
^ P/N 80010 (2B/2BR) - 89 ml (3 oz) tube boxed
^ P/N 80016 (2BR) - 89 ml (3 oz) tube carded
^ P/N 80011 (2C) - 325 ml (11 oz) tube boxed

Warranty Information
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 287
Chevrolet Venture V6-3.4L VIN E 2612

For vehicles repaired under warranty, use the table.

Disclaimer
Technical Service Bulletin # 01-08-61-003 Date: 010401

Special Tools - Frame Insulator Tool


File In Section: 08 - Body and Accessories

Bulletin No.: 01-08-61-003

Date: April, 2001

INFORMATION

Subject:
Information - New Frame Insulator Remover/Installer From Kent Moore

Models:
1997 - 2000 Buick Park Avenue
1997 - 2002 Buick Century, Regal
2000 - 2001 Buick LeSabre
2002 Buick Rendezvous
2000 Cadillac DeVille, Seville
1997 - 2001 Chevrolet Venture
1997 - 2002 Chevrolet Lumina, Monte Carlo
2000 - 2002 Chevrolet Impala
1998 - 2002 Oldsmobile Intrigue
2001 Oldsmobile Aurora
1997 - 1998 Pontiac Trans Sport
1997 - 2002 Pontiac Grand Prix
1999 - 2001 Pontiac Montana
2000 - 2001 Pontiac Bonneville
2001 - 2002 Pontiac Aztek

This bulletin contains information regarding a new service tool Frame Insulator Remover/Installer J-45296 which is now available from Kent
Moore.

This tool aids in the removal and installation of the frame lower front insulator.

Tool Usage Procedure

Within SI2000, refer to the Frame and Underbody subsection for the complete procedure for replacing the frame lower front insulator.
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 288
Chevrolet Venture V6-3.4L VIN E 2613

1. Install the J-45296 Frame Insulator Remover/Installer to the front frame lower insulator you are removing.

2. Using J-45296 Frame Insulator Remover/Installer, remove the front frame lower ins~ator from the frame.

3. Using J-45296 Frame Insulator Remover/Installer, install the front frame lower insulator to the front frame.

DisclaimerTechnical Service Bulletin # 02-08-98-003 Date: 030621

Body - Information On Expandable Acoustic Foam


Info - Expandable Acoustic Foam (Two Component Sound Dampener) Usage with Collision Damage Repairs #02-08-98-003 - (Jun 21,
2002)

Expandable Acoustic Foam (Two Component Sound Dampener) Usage with Collision Damage Repairs

2003 and Prior Passenger Cars and Light Duty Trucks

2003 HUMMER H2

When performing collision repairs or replacing some components on most GM model vehicles, it is important that the foam blocking material used
for noise, water and dust control be replaced as well.

This foam material is packaged as a two component material. This material is applicable for replacement of the original production material, since
both are a "closed cell material" and are not water absorbent.

TYPICAL LOCATIONS for this material are indicated on the illustrations below. SPECIFIC FOAM LOCATION WILL BE PROVIDED IN GM
SERVICE MANUALS IN THE NEAR FUTURE.

Two Component Material

This material has more of an industrial application, but can be obtained (from the sources listed below) in various quantities useful for collision
repairs.

It is especially useful when filling "blind" areas (areas that can't be seen) that require the expansion of the material to ensure sealing.
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 289
Chevrolet Venture V6-3.4L VIN E 2614

Our experiments indicate the following information:

Important: Do not use more than was needed for production applications.

- Over application of this material in some areas of the vehicle may change performance characteristics and is not recommended.
- It is recommended that a small amount be applied into a disposable container to become familiar with the rate of discharge and ensure proper
mixing of both material parts.

Contact the following sources for information on sales and distribution.


- For larger jobs (rocker box):
- *"FROTH PAK" 12 KIT, Insta-Foam Products, Inc., Disturbed by Essex Arg.
- Contact 1-800-246-4405, ext.11, (in Canada, contact Dow Chemicals at 1-800-366-4740).
- For smaller jobs (A pillar):
- *3M(R) Corporation, Flexible Foam 0.201L (6.8 oz), P/N 8463.
- In U.S., call 1-800-521-8100, ext 5165 (in Canada, 1-800-364-3577).
- *Kent Automotive, Urefoam Expandable 0.050L (1.7 oz), P/N 10630, or 0.296L (10 oz), P/N 10601.
- In U.S., call 1-800-654-6333 (in Canada, 1-800-563-1717).

*We believe these sources and their products to be reliable. There may be additional manufacturers of such products. General Motors does not
endorse, indicate any preference for or assume any responsibility for the products or equipment from these firms or for any such items which may
be available from other sources.

Important: As always, follow the manufacturer's recommendations for application and safety.

FIGURE Typical Foam Installation Areas (Cars)(c)


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 290
Chevrolet Venture V6-3.4L VIN E 2615

FIGURE Typical Foam Installation Areas (Trucks)(c) Technical Service Bulletin # 04-08-98-001 Date: 040526

Body - Metal Panel Bonding Additional Material


Info - Additional Material and Source for Metal Panel Bonding Adhesives #04-08-98-001 - (May 26,2004)

Additional Material and Source for Metal Panel Bonding Adhesives

2004 and Prior Passenger Cars and Trucks

2004 and Prior HUMMER H2

Recently, General Motors reviewed an additional source and material for the bonding of certain exterior metal panels when performing collision
repairs.

The 3M Corporation has introduced a new epoxy adhesive. 3M P/N 8116 has been recognized as meeting the performance guideline requirements
of GM 6449G Specification for Metal Panel Bonding Adhesives.

The addition of this product to the materials recognized for this performance capability increases the number to four, thus providing options for
material selection when repairing vehicles using the metal panel bonding process. Those recognized materials now included.

As always, follow the manufacturer's directions for application and curing times. Do not intermix products between different manufacturers.
Technical Service Bulletin # 00-08-64-007 Date: 000601

Front Door Window - Inoperative/Slow or Noisy


File In Section: 08 Body and Accessories

Bulletin No.: 00-08-64-007

Date: June, 2000


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 291
Chevrolet Venture V6-3.4L VIN E 2616

TECHNICAL

Subject:
Slow/Non-Moving (Chatters/Noisy) Glass, Bent Regulator Arms or Window is inoperative (Replace Run Channel and/or Weatherstrip)

Models:
1997-2000 Chevrolet Venture
1997-2000 Oldsmobile Silhouette
1997-1999 Pontiac Trans Sport
1999-2000 Pontiac Montana

Condition

Some customers may comment that the front door glass is slow or noisy when moving up or down or the window is inoperative.

Cause

The window run channel may be adjusted improperly which may cause the following:

^ The glass may be slow/non-moving.

^ The glass wears through the flocking on the weatherstrip and allows direct contact between the glass and the rubber of the weatherstrip, which
causes drag.

^ Bent regulator arms may be due to glass drag from the run window channel.

Correction

Adjust the window run channel upper attachment full forward and the lower attachment full rearward. Replace run channel and/or weatherstrip, if
necessary.

Parts Information

Parts are expected to be available from GMSPO, 6/5/00.

Warranty Information

For vehicles repaired under warranty, use the table.

Disclaimer
Procedure
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 292
Chevrolet Venture V6-3.4L VIN E 2617
1. Remove the door switch plate.

2. Disconnect the electrical connectors from the switch plate.

3. Remove the bezel behind the door handle.

4. Remove the bolts from the armrest.

5. Remove the trim panel retainers and remove the trim panel.

6. Remove the water deflector.

7. Remove the inner belt seal.

8. Remove the outer belt seal.

9. Raise the glass to gain access to the lower sash channel retaining clips. Push in on the retainers and slide the sash channel to release the glass.

10. Remove the glass from the door.

11. Remove the weatherstrip from the run channel.

12. Remove the bolts from the run channel and remove the run channel from the door.

13. Loosen the mirror for weatherstrip removal.

14. Remove the weatherstrip from the door.

15. Spray the backside of the new weatherstrip with window cleaner for ease of installation and install the weatherstrip.

16. Tighten the mirror retaining nuts.

Tighten
Tighten the nuts to 10 Nm (89 lb in).

17. Install the window run channel in the door and leave the retaining bolts finger tight.

18. With the window run channel installed, move the upper attachment full forward and the lower attachment full rearward.

Tighten
Tighten to 10 Nm (89 lb in).

19. Install the weatherstrip in the window lower run channel.

20. Install the glass door.

21. Install the outer belt seal.

22. Install the inner belt seal.

23. Install the water deflector using a 50.8 mm (2 in) wallpaper roller. Starting at the bottom center and working outboard, roll out the butyle
adhesive up the right and left sides. A 50.8 mm (2 in) roller can be purchased at a hardware or wallpaper store.

24. Install the trim panel.

25. Install the door trim panel bolts. Tighten

Tighten the bolts to 3 Nm (26 lb in).

26. Attach the electrical connectors to the switch and install the switch.

27. Install the door handle bezel.Technical Service Bulletin # 01-08-57-006 Date: 011101

Body/Frame - Mildew Odor, Water Leaks


File In Section: 08 - Body and Accessories

Bulletin No.: 01-08-57-006

Date: November, 2001


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 293
Chevrolet Venture V6-3.4L VIN E 2618

TECHNICAL

Subject:
General Waterleak Diagnosis Guide

Models:

1997-1999 Buick GL8 (Export China)


1997-1999 Chevrolet Trans Sport (Export Europe)
1997-2002 Chevrolet Venture
1997-2002 Oldsmobile Silhouette
1997-2002 Pontiac Trans Sport/Montana

This bulletin contains information on various waterleak conditions. Refer to the following table for a quick reference to the various conditions and
the corresponding illustrations.

Condition 1

Some customers may comment on a mildew odor or that the front floor is wet.

Cause

The water deflector may not be seated properly to the door sheet metal.

Correction

Seat the water deflector to the door surface at the primary locations. Refer to the arrows in the illustration. If the adhesive surface is dirty and the
water deflector needs to be replaced, follow the procedure listed below.

Service Procedure

1. The adhesive surface must be clean, dry and free of dirt or contaminants. Clean the door surface (around the perimeter of the water deflector)
with one of the cleaners listed below, or an equivalent.

2. Install the water deflector to the inner panel.

3. Pull the harness connectors through their respective holes or slits.

4. Position the outer perimeter of the deflector to the door inner panel by working from the bottom center outboard. Make sure the butyl
adhesive is below the drain holes.
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 294
Chevrolet Venture V6-3.4L VIN E 2619

5. Using a 50 mm (2 in) wallpaper roller, roll out the butyl adhesive. Start at the bottom center and work outboard, up the right and left sides. A
50 mm (2 in) roller can be purchased at a hardware or wallpaper store.

Condition 2

Some customers may comment on a mildew odor or that the front floor is wet.

Cause

There may be a void in the seam sealer at the front of dash.

Correction

1. Run water over the strut tower. Refer to the arrow in the illustration.

2. Inspect the seam on the inside of the vehicle. Refer to the highlighted line in the illustration.

3. Clean the area with one of the cleaners listed below.

4. Seal the voids with seam sealer. Refer to the list below.

Condition 3

Some customers may comment on a mildew odor or that the front floor is wet.

Cause
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 295
Chevrolet Venture V6-3.4L VIN E 2620

The wire harness, cables or the HVAC drain that passes through the front of dash may not be sealed properly. Refer to the arrows in the above
illustration.

Correction

Locate the leak by running water down the front of the dash under the hood. Clean the area with one of the cleaners listed below. Seal the area with
a seam sealer listed below.

Condition 4

Some customers may comment on water dripping from the top of the windshield.

Cause

Important:
A large amount water may be able to enter the vehicle through small holes in the body seam sealer.

^ To check for a void in the windshield urethane, run LOW pressure water under the windshield surround molding.

^ If no leak is present, water may be entering from a hole in the body seam sealer at the "C" pillar and then running forward to the windshield.
Refer to the arrow in the illustration above. Remove the pitch molding, inspect the patch sealers (from "C" pillar to "D" pillar) for holes, folds,
or mis-application. Also, inspect the sheet metal at the top corner of the "C" pillar for holes or visible folds.
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 296
Chevrolet Venture V6-3.4L VIN E 2621

Correction

1. The affected surface must be clean, dry and free of dirt or contaminants. Clean the surface with one of the cleaners listed below, or an
equivalent.

2. Fill the pin hole(s) with a clean seam sealer.

Condition 5

Some customers may comment on a mildew odor or that the front floor/mid-floor is wet.

Cause

There may be a void in the butyl tape/sealer on the hem flange under the auxiliary seal. Refer to the highlighted line in the illustration above.

Correction

1. Clean the flange and weatherstrip with one of the cleaners listed below.

2. Apply some weatherstrip adhesive in the weatherstrip retaining cavity and reinstall the weatherstrip to the hem flange.

Condition 6

Some customers may comment on a mildew odor or the that the mid-floor is wet.

Cause

The "C" pillar may have a sealer void. Refer to the shaded area in the illustration above.

Correction

Clean the area with one of the cleaners listed below and seal with a seam sealer listed below.

Condition 7

Some customers may comment on water pooling up in the corner of the weatherstrip or that the mid-floor is wet.
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 297
Chevrolet Venture V6-3.4L VIN E 2622

Cause

The weatherstrip may allow water to wick in and pool up in the corner. Refer to the arrow in the illustration above.

Correction

Drill a small 3 mm (1/8 in) hole in the interior surface of the weatherstrip. This will allow the water to drain inside the weatherstrip and exit out the
existing holes in the outside of the weatherstrip.

Condition 8

Some customers may comment on clean water in the jack compartment.

Cause

The power sliding side door cable pass-through grommets may not be seated properly. Refer to the locations shown in the illustration above.

Correction

Make sure the power sliding side door grommets are seated properly. Seal the perimeter with weatherstrip adhesive as necessary.

Condition 9

Some customers may comment on dirty water in the jack compartment.

Cause
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 298
Chevrolet Venture V6-3.4L VIN E 2623

There may be a poor seal in the wheelhouse inner to outer sheet metal. Water is thrown off the wheels and forced up through the unsealed joint.
Refer to the illustration above.

Correction

Important:
Wear safety glasses and use compressed air to dry the area.

1. Clean the surface area with one of the cleaners listed below.

2. Seal the hole with one of the sealers listed below.

Condition 10

Some customers may comment on dirty water in the jack compartment.

Cause

There may be a void in the sealer between the inner and outer wheel house liner. Refer to the highlight in the illustration above.

Correction

Important:
Wear safety glasses and use compressed air to dry the area.

Clean the surface area with one of the cleaners listed below and then seal the hole with one of the sealers listed below.

Condition 11

Some customers may comment on wet carpet at the rear of the vehicle.

Cause
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 299
Chevrolet Venture V6-3.4L VIN E 2624

The weatherstrip may be turned in on the sides causing poor contact to the liftgate surface. Refer to the arrow in illustration above.

Correction

1. Remove the weatherstrip from the hem flange.

2. Bend the hem flange outboard to ensure a better seal contact.

Condition 12

Some customers may comment on wet carpet at the rear of the vehicle.

Cause

The weatherstrip may be turned down at the top causing poor contact to the liftgate surface. Refer to the illustration above.

Correction

Bend the hem flange upright to ensure a better seal.

Condition 13

Some customers may comment on wet carpet at the rear of the vehicle.

Cause
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 300
Chevrolet Venture V6-3.4L VIN E 2625

The taillight grommet may not be sealed. Refer to the illustration above.

Correction

Make sure the butyl tape is in place over the taillight grommet.

Condition 14

Some customers may comment that the headliner is wet at the rear of the vehicle.

Cause

The wire harness grommet may not be fully seated. Refer to the illustration above.

Correction

1. Fully seat the rubber grommet.

2. Seal the grommet, if necessary, with weatherstrip adhesive listed below.

Weatherstrip Adhesive

GM Weatherstrip Adhesive Gel (Black), P/N 12345097 (in Canada, use P/N 10953479)

Parts are currently available from GMSPO.

Cleaning Solvents

^ 3M(R) General Purpose Adhesive Cleaner, P/N 08984

^ Dominion Sure Seal, Sure Solve Stock BSS

^ Kent Acrosol(TM)

Seam Sealer

^ 3M(R) Clear Auto Sealer, P/N 08551

^ Kent High Tech Seam Sealer Clear, P/N 10200


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 301
Chevrolet Venture V6-3.4L VIN E 2626

^ Dominion Sure Seal Heavy Duty Drip Check LSC, Item # 9019

DisclaimerTechnical Service Bulletin # 04-07-30-006 Date: 040211

A/T - 4L65E, 4L60E, 4L60, 200-4R Oil Pump Spring


Bulletin No.: 04-07-30-006

Date: February 11, 2004

INFORMATION

Subject:
4L65-E, 4L60-E, 4L60 and 200-4R Automatic Transmission Oil Pump Spring First and Second Design Identification

Models:
2004 and Prior Passenger Cars and Light Duty Trucks
2003-2004 HUMMER H2

with 4L65-E, 4L60-E, 4L60 or 200-4R Automatic Transmission

The purpose of this bulletin is to identify the oil pump spring usage for the two different pump designs. Manufacturing of the first design oil pump
springs ended December 15, 2003. Manufacturing of the second design oil pump spring began December 16, 2003

The first design oil pump springs (206) and (207) DO NOT have any identification markings. The first design springs (206) and (207) use an inner
and outer spring, two springs.

The second design oil pump spring (245) is identified with tapered ends on the spring (245) as shown above. The second design spring (245) is a
single spring.
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 302
Chevrolet Venture V6-3.4L VIN E 2627

When servicing either (first design or second design) oil pump body, use the new single oil pump spring (245) with tapered ends.

DisclaimerTechnical Service Bulletin # 99-07-30-017A Date: 030201

A/T - Oil Cooler Flushing/Flow Check Procedures


File In Section: 07 - Transmission/Transaxle

Bulletin No.: 99-07-30-017A

Date: February, 2003

INFORMATION

Subject:
Automatic Transmission Oil Cooler Flushing and Flow Check Procedures

Models:
2003 and Prior GM Light Duty Trucks
2003 HUMMER H2
with Allison(R) Automatic Transmission (RPO M74)

This bulletin revises bulletin 99-07-30-017 to reflect the release of the new Transflow(R) J 45096 Transmission Cooling System Service Tool. The
Transflow(R) Transmission Cooling System Service Tool is to be used for all vehicles. Please discard Corporate Bulletin Number 99-07-30-017
(Section 07 - Transmission/Transaxle). Refer to Corporate Bulletin Number 02-07-30-052.

Important:
If you were sent here by the instruction booklet for the J 45096 TransFlow(R) machine, note that the table has been moved to Corporate
Bulletin Number 02-07-30-052.

DisclaimerTechnical Service Bulletin # 03-07-30-027 Date: 030601

A/T - Oil Cooler Flushing Frequently Asked Questions


File In Section: 07 - Transmission/Transaxle

Bulletin No.: 03-07-30-027

Date: June, 2003

INFORMATION

Subject:
Most Frequently Asked Questions and Answers for J 45096 TransFlow Transmission Oil Cooling System Flushing Machine

Models:
2004 and Prior Passenger Cars and Light Duty Trucks with Automatic
Transmission/Transaxle

2004 and Prior HUMMER H2

This bulletin is issued to help answer the most frequently asked questions and concerns about essential tool J 45096.

Q: Why doesn't the machine work below 18°C (65°F)?


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 303
Chevrolet Venture V6-3.4L VIN E 2628

A: The flow characteristics of ATF at temperatures below 18°C (65°F) does not provide accurate flow test results with the electronics used in the J
45096.

Q: Why didn't the unit come with a tank heater?

A: The vast majority of dealerships do not require a heater to keep the ATF above 18°C (65°F). As a result, the heater was deleted as a
cost-savings measure. A tank heater, J 45096-10, is currently available from Kent-Moore if your dealership requires it. Refer to Corporate
Bulletin Number 03-07-30-002A for suggestions on warming the ATF without using a heater blanket.

Q: Why does the machine fail new oil coolers?

A: Several reasons have been found. The most likely reason is the air pressure at the air hose connected to the J 45096 is less than 586 kPa (85
psi). Other reasons include a twisted hose inside the J 45096 at the bulkhead as a result of the nut turning when the waste or supply hose was
installed, the internal pressure regulator was improperly set at the factory or a problem with the cooler lines on the vehicle. Perform the J 45096
self-test as described on pages 9 and 10 of the Operation Manual. If a problem is still detected, refer to Troubleshooting on page 19 of the
Operation Manual. If a problem still persists, contact Kent-Moore Customer Service at 1-800-345-2233.

Q: What is the difference between steel and aluminum oil coolers?

A: The aluminum oil cooler tube is slightly thinner in construction than the steel oil cooler tube, which affects the oil flow rate. The fitting that is
protruding out of the radiator tank easily identifies the aluminum oil cooler. Refer to the Quick Reference card provided with the J 45096 in
order to identify the proper flow rate for the aluminum oil cooler.

Q: Why can't I use TransFlow for Allison transmission cooling Systems?

A: Validation of TransFlow is currently under development for light duty trucks equipped with the Allison automatic transmission. TransFlow is
based on the existing MINIMUM flow rate specification through the transmission oil cooling system. The Allison transmission oil cooling
system only has MAXIMUM oil flow rates specified and J 45096 does not have the capability to test the transmission oil cooling system at the
maximum oil flow rate specification.

Q: Why doesn't GM publish a specification for auxiliary transmission oil coolers?

A: The auxiliary oil cooler used with GM vehicles does not contain an internal turbulator plate like the radiator tank oil cooler does. Therefore,
there is no internal restriction that would affect the flow rate through the oil cooling system so a specification for auxiliary oil cooler is not
required. Keep in mind, kinks and damage to the auxiliary cooler and lines can affect the flow rate through the system.

Q: Why did GM drop the labor time for transmission repairs?

A: The labor for flushing and flow testing the transmission oil cooling system is included with the R&R labor of the "K" labor operations that
require transmission removal. The time required to use the J 45096 to perform the flush and flow test is much less than that of the J 35944-A.
The warranty labor savings allowed GM to provide the J 45096 at no cost to dealerships.

Q: Why didn't the machine come with the adapters to hook up to the car?

A: The J 45096 was designed to use the previously released essential cooler line adapters for the J 35944-A. All adapters are listed on page 17 of
the Operation Manual and can be ordered from Kent-Moore at 1-800-345-2233.

Q: How do I connect the J 45096 to a Catera, Prizm or a Vibe?

A: These vehicles, along with many other models, only require barbed fittings to connect to the rubber cooler hose. These fittings are commercially
available and already found in many shops.

Q: Why didn't I receive an Operation Manual with the machine?

A: The Operation Manual was packaged in the upper portion of the shipping carton. If the shipping carton was lifted off the base without opening
the top of the carton, the Operation Manual could have been discarded with the carton. Replacement Operation Manual packages can be
obtained from Kent-Moore Customer Service at 1-800-345-2233.

Q: Why can't I re-use the transmission fluid I use for flushing?

A: The very fine metal and clutch material debris from the transmission failure in the ATF causes failures with the hall effect speed sensors that are
used to measure the flow rate. To avoid costly repairs, expensive filters, regular maintenance and problems caused by a partially restricted filter,
the filter was not included.

Q: What do I do if I need service on my machine?

A: Call Kent-Moore Customer Service at 1-800-345-2233. The J 45096 has a one-year warranty.

Q: Can I flush and flow engine oil coolers?


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 304
Chevrolet Venture V6-3.4L VIN E 2629

A: The engine oil cooler flow rates, the appropriate adapters and an acceptable procedure are currently under development.

DisclaimerTechnical Service Bulletin # 04-06-04-051B Date: 060104

Fuel System - Fuel Injector Maintenance Cleaning


Bulletin No.: 04-06-04-051B

Date: January 04, 2006

INFORMATION

Subject:
Maintenance Cleaning of Fuel Injectors

Models:
2006 and Prior All General Motors Passenger Cars and Trucks
2003-2006 HUMMER H2
2006 HUMMER H3

Supercede:

This bulletin is being revised to add models and model years and update the name and part number of GM Fuel System Treatment. Please discard
Corporate Bulletin Number 04-06-04-051A (Section 06 - Engine/Propulsion System).

General Motors is aware that some companies are marketing tools, equipment and programs to support fuel injector cleaning as a preventative
maintenance procedure. General Motors does not endorse, support or acknowledge the need for fuel injector cleaning as a preventative maintenance
procedure. Fuel injector cleaning is approved only when performed as directed by a published GM driveability or DTC diagnostic service
procedure.

Due to variation in fuel quality in different areas of the country, the only preventative maintenance currently endorsed by GM regarding its gasoline
engine fuel systems is the addition of GM Fuel System Treatment PLUS, P/N 88861011 (for U.S. ACDelco(R), use P/N 88861013) (in Canada,
P/N 88861012), added to a tank of fuel at each oil change. Refer to Corporate Bulletin Number 03-06-04-030A for proper cleaning instructions.

DisclaimerTechnical Service Bulletin # 02-06-04-053 Date: 021001

Emissions - Revised DTC P0403 (EGR Solenoid Circuit)


File In Section: 06 - Engine/Propulsion System

Bulletin No.: 02-06-04-053

Date: October, 2002

SERVICE MANUAL UPDATE

Subject:
Revised DTC P0403 Exhaust Gas Recirculation (EGR) Solenoid Control Circuit

Models:
2000 Chevrolet Venture
2000 Oldsmobile Silhouette
2000 Pontiac Montana
with 3.4L Engine (VIN E - RPO LA1)
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 305
Chevrolet Venture V6-3.4L VIN E 2630

This bulletin is being issued to revise DTC P0403 Exhaust Gas Recirculation (EGR) Solenoid Control Circuit in the Engine Controls - 3.4L
sub-section of the Service Manual. Please replace the current information in the Service Manual with the following information.
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 306
Chevrolet Venture V6-3.4L VIN E 2631
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 307
Chevrolet Venture V6-3.4L VIN E 2632

This information has been updated within SI. If you are using a paper version of this Service Manual, please make a reference to this bulletin on the
affected page.

Disclaimer

Technical Service Bulletin # 01-05-23-003 Date: 010301

Front/Rear Brakes - Revised Tool Requirements


File In Section: 05 - Brakes

Bulletin No.: 01-05-23-003

Date: March, 2001

SERVICE MANUAL UPDATE

Subject:
Revised Tool Requirements for Front and Rear Brake Caliper Overhaul

Models:
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 308
Chevrolet Venture V6-3.4L VIN E 2633
1997-2001 Buick Park Avenue, Regal
1997-2001 Buick Regal (Export China)
2000-2001 Buick LeSabre
1997-2001 Cadillac DeVille, Seville
2000-2001 Cadillac Eldorado
1997-2001 Chevrolet Trans Sport (Export China), Venture
2000-2001 Chevrolet Impala, Lumina, Monte Carlo
1997-2001 Oldsmobile Aurora, Silhouette
1998-2001 Oldsmobile Intrigue
1997-2001 Pontiac Grand Prix, Montana, Trans Sport
2000-2001 Pontiac Bonneville

This bulletin is being issued to revise the tool requirements for the front and rear brake caliper overhaul procedures in the Disc-Brake sub-section of
Brakes in the appropriate Service Manual. Please use the following to replace the existing information in the Service Manual.

This information has been updated within SI2000. If you are using a paper version of this Service Manual, please mark a reference to this bulletin
on the affected page in the Disc Brake sub-section of the Service Manual.

DISCLAIMER

Front Brake Caliper Overhaul Procedure


(All Above Listed Vehicles)

Caution:
Do not place fingers in front of the caliper piston(s) in an attempt to catch or protect it when applying compressed air. The piston(s) can fly out
with force and could result in serious bodily injury.

Notice:
Use clean cloths to pad the interior of the caliper housing during piston removal. Use just enough air to ease the piston out of the bores. If the
pistons are blown out, even with the padding provided it may be damaged.

1. Remove the front brake caliper from the vehicle.

2. Remove the brake caliper piston from the caliper bore by directing low pressure compressed air into the caliper bore through the fluid inlet
hole.
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 309
Chevrolet Venture V6-3.4L VIN E 2634

3. Using a small wooden or plastic tool, remove the caliper piston seal (2) from the seal counterbore in the caliper (1) and discard the boot seal.

4. Using a small wooden or plastic tool, remove the piston seal (4) from the caliper bore and discard the piston seal.

5. Remove the bleeder valve (5) and cap (6) from the caliper (1).

Important:
Do not use abrasives to clean the brake caliper piston.

6. Clean the brake caliper piston bore and seal counterbore and the caliper piston with denatured alcohol, or equivalent.

7. Dry the caliper piston bore and counterbore and the piston with non-lubricated, filtered air.

8. Inspect the caliper bore for cracks, scoring, pitting, excessive rust and/or excessive corrosion.

9. If light rust or light corrosion are present in the caliper bore, attempt to remove the imperfection with a fine emery paper. If the imperfection
cannot be removed, replace the caliper assembly.

10. If cracks, scoring, pitting, excessive rust and/or excessive corrosion are present in the caliper bore, replace the caliper assembly.

11. Inspect the caliper piston for cracks, scoring and/or damage to the finished surface area. Replace the caliper piston if any of these conditions
exist.

12. Lubricate the new piston seal with Delco Supreme 11(R), P/N 12377967 (in Canada use P/N 992668), or equivalent DOT-3 brake fluid from
a clean, sealed brake fluid container.

13. Install the lubricated new piston seal into the caliper bore.

14. Install the caliper piston into the caliper bore. Press the piston to the bottom of the bore.

15. Install the new piston dust boot seal over the piston.

16. Use J-35777 to fully seat the caliper piston seal into the counterbore.

17. Install the bleeder valve and cap to the caliper and tighten the valve securely.

18. Install the front brake caliper to the vehicle.


Rear Brake Caliper Overhaul Procedure
(See Vehicles Listed Below)

^ 1999-2001 Buick Regal


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 310
Chevrolet Venture V6-3.4L VIN E 2635

^ 1999-2001 Buick Regal (Export China)

^ 2000-2001 Chevrolet Impala, Monte Carlo, Trans Sport (Export China)

^ 1998-2001 Oldsmobile Intrigue

^ 1997-2001 Pontiac Grand Prix

Caution:
Do not place fingers in front of the caliper piston(s) in an attempt to catch or protect it when applying compressed air. The piston(s) can fly out
with force and could result in serious bodily injury.

Notice:
Use clean cloths to pad the interior of the caliper housing during piston removal. Use just enough air to ease the piston out of the bores. If the
pistons are blown out, even with the padding provided, it may be damaged.

1. Remove the rear brake caliper from the vehicle.

2. Remove the bleeder valve and cap from the caliper housing.

3. Remove the brake caliper piston from the caliper bore by directing low pressure compressed air into the caliper bore through the fluid inlet
hole.

4. Remove the retaining ring that secures the dust boot to the caliper housing.

5. Remove the piston dust boot seal (2) from the seal counterbore in the caliper. Discard the boot seal.

6. Using a small wooden or plastic tool, remove the piston seal (4) from the caliper bore. Discard the piston seal.
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 311
Chevrolet Venture V6-3.4L VIN E 2636

Important:
Do not use abrasives to clean the brake caliper piston.

7. Clean the brake caliper piston bore and seal counterbore and the caliper piston with denatured alcohol, or equivalent.

8. Dry the caliper piston bore and counterbore and the piston with non-lubricated, filtered air.

9. Inspect the caliper bore for cracks, scoring, pitting, excessive rust and/or excessive corrosion.

10. If light rust or light corrosion are present in the caliper bore, attempt to remove the imperfection with a fine emery paper. If the imperfection
cannot be removed, replace the caliper assembly.

11. If cracks, scoring, pitting, excessive rust and/or excessive corrosion are present in the caliper bore, replace the caliper assembly.

12. Inspect the caliper piston for cracks, scoring and/or damage to the chrome plating. Replace the caliper piston if any of these conditions exist.

13. Lubricate the new piston seal (4) with Delco Supreme 11(R), P/N 12377967 (in Canada, use P/N 992668), or equivalent DOT-3 brake fluid
from a clean, sealed brake fluid container.

14. Install the lubricated new piston seal (4) into the caliper bore.

15. Install the bottom half of the caliper piston (3) into the caliper bore.

16. Install the new piston dust boot seal (2) over the caliper piston (3).

17. Compress the caliper piston (3) to the bottom of the caliper bore.

18. Fully seat the piston dust boot seal (2) into caliper counterbore.

19. Install the retaining ring that secures the dust boot to the caliper housing.

20. Install the bleeder valve and cap to the caliper and tighten the valve securely.

21. Install the rear brake caliper to the vehicle.Technical Service Bulletin # 01-05-23-011A Date: 020201

Brakes - Rattling Noise


File In Section: 05 - Brakes

Bulletin No.: 01-05-23-O11A

Date: February, 2002


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 312
Chevrolet Venture V6-3.4L VIN E 2637

TECHNICAL

Subject:
Rattle Type Noise Coming from Front of Vehicle
(Install Front Brake Caliper Service Kit)

Models:

2000-01 Buick Century, Regal


2000-01 Chevrolet Impala, Monte Carlo, Venture
2000-01 Oldsmobile Intrigue, Silhouette
2000-01 Pontiac Grand Prix, Montana

This bulletin is being revised to remove Chevrolet Lumina from the Models section and to update the condition information. Please discard
Corporate Bulletin Number 01-05-23-11 (Section 05 - Brakes).

Built Prior to the VIN Breakpoints shown.

Condition

Some customers may comment about a rattle type noise coming from the front of the vehicle. This noise usually occurs at vehicle speeds under 48
km/h (30 mph) and while driving over bumps. The noise can usually be eliminated by a light application of the brake pedal.

Cause

This condition may be caused by too much clearance between the front brake caliper bracket and the caliper pins in the bottom of the bracket bores.

Correction

Install front brake caliper service kits to both sides of the vehicle using the following service procedure. Each kit contains 2 pins, 2 boots, and 2
packets of grease.

Service Procedure

1. Raise and suitably support the vehicle. Refer to Lifting and Jacking the Vehicle in General Information.

2. Remove both the front tire and wheel assemblies.

3. Hand tighten 2 wheel nuts to retain the rotor to the hub.


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 313
Chevrolet Venture V6-3.4L VIN E 2638

4. Install a large C-clamp (2) over the top of the brake caliper and against the back of the outboard brake pad.

5. Tighten the C-clamp until the caliper piston is pushed into the caliper bore enough to slide the caliper off the rotor.

6. Remove the C-clamp from the caliper.

7. Remove the caliper pin bolts (3) and discard. New bolts are supplied with the service kit.

8. Remove the caliper (1) from the caliper bracket (2) and support the caliper with heavy mechanic's wire, or equivalent.

9. Using a flat bladed tool or punch, carefully tap the caliper pin boots from the brake caliper bracket and discard.

10. Remove and discard the bushings from the brake caliper bracket bores. Carefully insert a small screwdriver into the brake caliper bracket
bore, then rotate and pull the bushing outward to remove.

11. Remove the brake pads from the brake caliper bracket.

12. Thoroughly clean the brake caliper bracket bores of all lubricant.

13. Install the brake pads to the brake caliper bracket.

14. Lubricate the brake caliper bracket bores. Divide the large packet of grease, P/N 18046532; put one-half packet into each bore.
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 314
Chevrolet Venture V6-3.4L VIN E 2639

15. Lubricate the new caliper pin boots. Use the small packet of grease, P/N 18046645, only on the bottom internal threads (2).

16. Install the new caliper pin boots into the caliper pin bores (3) on the bracket. Carefully tap boots into bores using a deep well socket or
equivalent.

17. Install the caliper over the rotor and onto the caliper bracket. Ensure that the caliper pin boots are not pinched.

Important:
The leading caliper pin, or top pin, has a bushing as part of the assembly. The trailing caliper pin, or bottom pin, is a solid design.

18. Install the new caliper pin bolts (1). It is important to note which caliper pin is designed for the correct bore. The leading caliper pin, or top
pin, has a bushing as part of the assembly. The trailing caliper pin, or bottom pin, is a solid design. Ensure that the bolt boots fit securely in
the groove of the pin bolts. Be sure not to pinch or tear the boots. If the boots are damaged, they must be replaced.

Tighten

Tighten the bolts to 95 N.m (70 lb ft).

19. Remove the 2 wheel nuts retaining the rotor to the hub.

20. Repeat the above steps for the other side.

21. Install both the front tire and wheel assemblies. Tighten the wheel nuts using the J 39544 kit.

22. Lower the vehicle.

Parts Information
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 315
Chevrolet Venture V6-3.4L VIN E 2640

Parts are currently available from GMSPO.

Warranty Information

For vehicles repaired under warranty, use the table.

DisclaimerTechnical Service Bulletin # 01-05-23-006A Date: 010601

Brake Calipers - Revised Fastener Requirements


File In Section: 05 - Brakes

Bulletin No.: 01-05-23-006A

Date: June, 2001

SERVICE MANUAL UPDATE

Subject:
Revised Fastener Requirements for Front and Rear Brake Caliper Bracket Replacement

Models:
1997-2001 Buick Century, Regal
1997-2001 Buick Regal (Export China)
1997-2001 Chevrolet Trans Sport (Export China), Venture
2000-2001 Chevrolet Impala, Monte Carlo
1998-2001 Oldsmobile Intrigue
1997-1998 Pontiac Trans Sport
1997-2001 Pontiac Grand Prix
1999-2001 Pontiac Montana

This bulletin is being revised to update the model information. Please discard Corporate Bulletin Number 01-05-23-006 (Section 05 - Brakes).

This bulletin is being issued to revise the fastener requirements for the front and rear brake caliper bracket replacement procedures in the
Disc-Brake sub-section of Brakes in the appropriate Service Manual. Please use the following to replace the existing information in the Service
Manual.

This information has been updated within SI2000. If you are using a paper version of this Service Manual, please mark a reference to this bulletin
on the affected page in the Disc-Brake sub-section of the Service Manual.

Front Brake Caliper Bracket Replacement


(All Above Listed Vehicles)

1. Remove the caliper from the mounting bracket and support the caliper with heavy mechanics wire or equivalent. It is not necessary to
disconnect the hydraulic brake flexible hose from the caliper.

2. Remove the front brake pads.


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 316
Chevrolet Venture V6-3.4L VIN E 2641

3. Remove the caliper bracket bolts (2).

4. Remove the caliper bracket (1).

Important:
To ensure that the proper clamp load will be present when installed, it is imperative that the threads on the caliper bracket bolts, as well as the
mounting holes in the knuckle, be cleaned of all debris and inspected before proceeding with installation.

5. Clean and visually inspect threads of the caliper bracket bolts (2) and mounting holes in the knuckle.

6. Apply LOCTITE(R) THREAD LOCKER 272 (GM P/N 12345493) or equivalent to the threads of the brake caliper bracket bolts (2).

7. Install the caliper bracket (1) with the bracket bolts (2).

Tighten

Tighten the caliper bracket bolts to 180 N.m (133 lb ft).

8. Install the front brake pads.

9. Install the caliper.

Rear Brake Caliper Bracket Replacement (See Vehicles Listed Below)

^ 1999-2001 Buick Century, Regal

^ 1999-2001 Buick Regal (Export China)

^ 2000-2001 Chevrolet Impala, Monte Carlo

^ 2000-2001 Chevrolet Trans Sport (Export China)

^ 1998-2001 Oldsmobile Intrigue

^ 1997-2001 Pontiac Grand Prix

1. Remove the caliper from the mounting bracket and support the caliper with heavy mechanics wire or equivalent. It is not necessary to
disconnect the hydraulic brake flexible hose from the caliper.
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 317
Chevrolet Venture V6-3.4L VIN E 2642

2. Remove the rear brake pads.

3. Remove the caliper bracket bolts (2).

4. Remove the caliper bracket (1).

Important:
To ensure that the proper clamp load will be present when installed, it is imperative that the threads on the caliper bracket bolts, as well as the
mounting holes in the knuckle, be cleaned of all debris and inspected before proceeding with installation.

5. Clean and visually inspect threads of the caliper bracket bolts (2) and mounting holes in the knuckle.

6. Apply LOCTITE(R) THREAD LOCKER 272 (GM P/N 12345493) or equivalent to the threads of the brake caliper bracket bolts (2).

7. Install the caliper bracket (1) with the bracket bolts (2).

Tighten

Tighten the caliper bracket bolts to 115 N.m (85 lb ft).

8. Install the rear brake pads.

9. Install the caliper.

DisclaimerTechnical Service Bulletin # 03-05-24-001A Date: 050321

Brakes - Wheel Cylinder Inspection Guidelines


Bulletin No.: 03-05-24-001A

Date: March 21, 2005


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 318
Chevrolet Venture V6-3.4L VIN E 2643

INFORMATION

Subject:
Service Information Regarding Rear Brake Drum Wheel Cylinder Inspections

Models:
2005 and Prior GM Passenger Cars and Trucks
2005 and Prior Saturn Vehicles

with Rear Drum Brakes

Supercede:

This bulletin is being revised add model years and include all GM vehicles. Please discard Corporate Bulletin Number 03-05-24-001 (Section 03 -
Suspension).

This bulletin provides information on proper inspection of rear drum brake wheel cylinders.

Important:
It is not recommended that dust boots be removed during inspection processes as dirt and debris could contaminate the wheel cylinder bore
causing premature wear of the wheel cylinder. In addition, most bores should look damp and some lubricant may drip out from under the boot
as a result of lubricant being present.

All rear drum brake wheel cylinders are assembled with a lubricant to aid in assembly, provide an anti-corrosion coating to the cylinder bore, and
lubricate internal rubber components. As a result of this lubrication process, it is not uncommon for some amount of lubricant to accumulate at the
ends of the cylinder under the dust boot.

Over time, the lubricant may work its way to the outside of the boot and cause an area of the boot to look damp. Evidence of a damp area on the
boot does not indicate a leak in the cylinder. However, if there is excessive wetness (i.e. drips) coming from the boot area of the wheel cylinder, it
could indicate a brake hydraulic fluid leak requiring wheel cylinder replacement. (Refer to the Wheel Cylinder Replacement procedures in the
appropriate Service Manual.)

DisclaimerTechnical Service Bulletin # 89358 Date: 881101

Battery - Diagnosis and Charging


Bulletin No. T-89-35
File in Group 8
Number 89
Corp. Ref. No. 886401R
Date Nov. 1988
SUBJECT: DELCO FREEDOM BATTERY DIAGNOSIS AND CHARGING

MODELS AFFECTED: ALL

This bulletin outlines the following service information:

I. Battery Storage: (In-Vehicle storage) Discusses battery storage procedures, parasitic loads, and includes a chart of fuses to pull to
reduce these loads during storage.

II. Warranty Policy: Briefly discusses new warranty procedure as it pertains


to battery charge and test (as outlined in DSIB 89-I-9).

III. Testing: Some brief tips for visual inspection and charging
cautions.

IV. Diagnosing Parasitics: Contains an important procedure required to properly


test 1986-1988 Eldorados and Sevilles and 1987-1988 Allantes for parasitic drains
(recommended for all carlines).

V. Charging: Tips relating to quick charging procedures. Also lists other sources of information.
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 319
Chevrolet Venture V6-3.4L VIN E 2644

Read all this information. Try recharging a deeply discharged battery; review training materials if necessary. The majority of deeply discharged
batteries can be recharged if proper procedures are followed.
CAUTION: BATTERIES PRODUCE EXPLOSIVE GASES Always shield eyes and face from battery. Cigarettes, flames, or sparks could cause
battery to explode. Do not charge or use booster cables or adjust terminal post connections without proper instructions and training.

CAUTION: BATTERIES CONTAIN SULFURIC ACID WHICH CAN CAUSE SEVERE BURNS
Batteries contain sulfuric acid. Avoid contact with skin, eyes or clothing. In the event of accident, flush with water and call a physician
immediately.

I.Battery Storage In Vehicle


Cadillacs have several electronic devices which result in very small but continuous current drains on batteries, commonly referred to as "parasitic
loads". Parasitic loads may cause vehicles, not used for an extended period of time, to develop deeply discharged and/or permanently damaged
batteries. Discharged batteries can freeze at temperatures as high as +20~F, causing permanent damage. Batteries that have been frozen should be
scrapped. Never attempt to recharge or use a battery which has been frozen.
To prevent frozen or damaged batteries, assure that the battery green dot is visible before storing the vehicle. The negative battery cable should be
disconnected on vehicles which are not going to be in service within a 30-day period. If this is not possible, batteries should be recharged
periodically, every 30-60 days, until the green dot is visible (see section on charging). NOTE:
Disconnecting the battery may disable any vehicle security/anti-theft systems!

NOTICE: The ignition switch, headlights, RAP, etc., must be off when connecting or disconnecting battery jumper cables or chargers. Failure to
do so may overstress or damage the ECM or other electronic components. Disconnecting jumper cables with the engine running may
cause voltage surges that could damage headlamp bulbs or other electronic components.

FIGURE 1 - RECOMMENDED FUSES TO PULL TO MINIMIZE PARASITICS DURING STORAGE

When disconnecting the negative battery cable is not practical for storage, Figure 1 can be used to determine which fuses should be pulled to
minimize the parasitic drain. The "Primary" fuse should be pulled and placed in a location in the vehicle where sales and service personnel can
easily find and reinstall it.

The fuse-pull suggestions found below, in Figure 1, are not designed to completely eliminate parasitic load; only disconnecting the battery negative
cable can accomplish this. Rather, it should help eliminate some of the major draws in a convenient manner.

II. Warranty Policy


Following proper testing and parasitic diagnosis procedures are in the best interests of the dealership in light of Warranty Policies and procedures
outlined in DSIB 89-I-9. This bulletin states that Labor Operation N0100, "Battery charge and test", is to be used only in case of new vehicles
received from the carrier with a discharged or "Dark Eye" battery. Recharge and/or replacement of new vehicle batteries on unsold cars in dealer
inventory are the responsibility of the dealership.
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 320
Chevrolet Venture V6-3.4L VIN E 2645

FIGURE 2 - WARRANTY PROCEDURE UNDER VARIOUS CONDITIONS

If a condition of discharged battery is a customer concern on a delivered vehicle, the root cause of the discharge should be diagnosed and repaired
before the battery is charged and tested. Battery charge and test on delivered vehicles is to be submitted for approval at no more than 0.3 "Other
Labor Hours" and is to accompany the repair operation that corrects the root cause of the discharge. Refer to Figure 2 on the next page.

III. Testing the Battery


A. Visual Test

Check for obvious damage, such as cracked or broken case or cover that is permitting loss of electrolyte. If obvious damage is noted, replace
the battery. Determine the cause of damage and correct as needed. If battery terminals are severely damaged, for instance loose, burned, or
broken, replacement of the battery is recommended.

Evidence of small amounts of electrolyte leakage, especially around the vent holes, does not necessarily indicate the battery is defective. The
leakage could have been caused by overcharging or tipping of the battery. If a small amount of the electrolyte leakage is detected, the battery
should be fully charged OUT OF THE CAR so that any electrolyte that may escape does not damage the bumper filler panels or other
components.
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 321
Chevrolet Venture V6-3.4L VIN E 2646

FIGURE 3 - BUILT-IN HYDROMETER

B. Reading Built-In Hydrometer

Look straight down into the built-in hydrometer to observe its reading, clean and use a flashlight if necessary, and tap lightly on top of the
hydrometer to dislodge any trapped air bubbles that might prevent a correct reading. Refer to Figure 3.

IV. Diagnosing Discharged Batteries and Parasitic Battery Drains


All no-start, slow cranking, and/or frequently discharged battery conditions should be thoroughly diagnosed to avoid unnecessary replacement of
batteries. The battery should be charged and load tested in accordance with established service procedures as described in the Cadillac Service
Information Manual before considering battery replacement. Examples of conditions causing low charged or discharged batteries are:

^ Extended storage of vehicles.


^ Batteries already discharged when vehicle is received, due to handling in transit and at assembly.
^ Extended cranking periods due to plug fouling.
^ Accessory lights left on with engine not running (courtesy, glove box, trunk lights).
^ Insufficient recharge (ampere-hours) of discharged battery.
^ Charging system problems.
^ Continuous current draw on battery through parasitic drain.

FIGURE 4 - PARASITIC LOADS BY CARLINE

As was discussed previously in "Battery Storage", today's Cadillacs have several electronic devices which result in very small but continuous
current drains on their batteries, commonly referred to as "parasitic loads". A parasitic drain of up to 50mA is considered normal, 30mA being
about average. Any battery draw above 50mA, with ignition off and retained accessory power disabled (if so equipped), is excessive. Figure 4 gives
approximate average values of design parasitic current draw for each carline.
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 322
Chevrolet Venture V6-3.4L VIN E 2647
Also, refer to the table of component parasitic loads found above under "Battery Storage". These values should only be used as general guidelines
when diagnosing suspect components.

FIGURE 5 - PROPER PARASITIC LOAD DIAGNOSTIC PROCEDURE

A. How to Check the Battery Drain (Refer to Figure 5)


When checking any type of current draw, it is important to use an ammeter or digital multimeter to measure the amperage.

The electrical circuitry of most Cadillac vehicles require that the Body Computer Module (BCM) and the Central Power Supply (CPS) get an
initialization charge whenever the battery power is first provided. This initialization occurs with the ignition key in the "OFF" position, and
depending on how long the battery has been disconnected, the initial draw may last from 1 to 3 seconds and can range between 0.5 and 9.0 amps.
Therefore, to prevent misleading readings or unnecessary fuse replacement on the digital multi-meter, J-29125, or similar equipment, the following
procedure is recommended. THIS PROCEDURE is PARTICULARLY CRITICAL ON THE 1987-1988 ALLANTE AND THE 1986-1988
ELDORADO AND SEVILLE. It is recommended as a good practice for all vehicles.
1. Disconnect the negative battery cable.

2. Install a battery side terminal adapter, AC-Delco ST1201 or equivalent, in the negative terminal of the battery.

3. Install a 3/8 nut, with standard threads (16 UNC) on the negative battery cable attaching screw to assure a good electrical contact with
the lead face on the cable for testing. Yellow or black finish nuts are generally non-conductive and should not be used.

4. With all lights, accessories, Retained Accessory Power (RAP), and the ignition switch off, connect a high capacity ammeter at least 10
amps from the negative battery cable to the side terminal adapter. This high capacity ammeter is connected to verify whether or not a
high current draw is occurring at a constant rate. It is this type of high current draw which will blow the fuse in lower capacity
ammeters. After the initial draw occurs, the ammeter reading should drop below 1 amp.

NOTE: If a high capacity ammeter is not available, install a section of heavy wire (preferably a battery cable) between the existing
battery negative cable and the side terminal adapter. Allow ample time (approximately 30-60 seconds) for the initial draw to
occur and proceed to step 5.

5. With the high capacity ammeter or battery cable section still connected, connect the digital multi-meter, set to the 2000 DCmA range, in
parallel with the high reading ammeter.
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 323
Chevrolet Venture V6-3.4L VIN E 2648

FIGURE 4 - PARASITIC LOADS BY CARLINE

FIGURE 6 - SAMPLE COMPONENT PARASITIC LOADS (IN mA)

6. Disconnect the high capacity ammeter and take the reading with the digital multi-meter.

A current draw of 5OmA or less (see values in Figures 4 and 6) indicates that all lights and accessories are off and that there is no
unexplained current draw. Care should be taken to allow for a time delay before reading the meter on vehicles equipped with Electronic
Level Control (ELC) (not found on Allante).

Due to this initialization process, test lamps CANNOT be used in place of ammeters to diagnose current draw conditions. The voltage drop across
the test lamp prevents the initialization process from occurring.

Clamp-On Ammeters:

Clamp-on ammeters may be used if the meter can measure in the milli-amp range and if the meter clamp can fit around all of the battery negative or
positive cables. All of the cables must fit in the clamp with the clamp closed to be sure that all of the parasitics are being measured. Zero the
clamp-on ammeter carefully. Magnetic fields from engine electrical items (generator, ignition, solenoids) and from shop sources (fluorescent lights,
power cables) can alter the clamp-on meter readings. If the parasitic readings are not repeatable, use the series measurement method described in
this bulletin.
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 324
Chevrolet Venture V6-3.4L VIN E 2649
B. Determining the Source of the Drain

Once it has been determined that a parasitic drain in excess of 50 mA exists, a visual inspection of the vehicle should be conducted.
Check to see if there are any unwanted lights on, motors running or switches/relays activating.

FIGURE 4 - PARASITIC LOADS BY CARLINE

If no cause for the draw is immediately apparent, it may be possible to narrow in on the source by systematically removing fuses and
circuit breakers, one by one, from the fuse panels. This should be done while monitoring the ammeter so that a disruption of the drain will
be evident. Refer to Figure 4 for average and maximum parasitic loads for various vehicle components.

FIGURE 6 - SAMPLE COMPONENT PARASITIC LOADS (IN mA)

Figure 6 gives an approximate indication of typical and maximum parasitic loads by component in milli-amps (mA).

In addition to parasitic loads, a certain amount of self-discharge is always occurring as a result of internal chemical reactions even when
the battery is not connected. The higher the ambient temperature, the greater the amount of self-discharge. This explains why the number
of discharged batteries may increase at your location in very hot weather. The original equipment battery has a much lower rate of
self-discharge than conventional batteries, however, self-discharge at 100 degrees ambient can be as high as 7mA.
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 325
Chevrolet Venture V6-3.4L VIN E 2650
V.Battery Charging
Dealership service personnel are advised to refer to Cadillac Serviceman Bulletin T-83-12, Group 6D for detailed instructions on:

1. Battery Side Terminal Connections


2. Battery Charging
3. Charging Time Required
4. Load Testing

NOTES:

1. The majority of discharged batteries can be recharged using normal battery charging procedures. Some deeply discharged batteries or
batteries which have been allowed to remain in a discharged state may need a higher charge voltage initially to start the recharging process.

2. The Freedom battery is more resistant to overcharging damage than conventional batteries. Boost or Quick-Charge settings on battery
chargers may be safely used in most instances. (This is not true of other non-Delco OE batteries and many aftermarket batteries.)

3. With the battery at room temperature, voltages as high as 15.0 volts to 16.0 volts may be safely used without causing battery damage. Cold
batteries require more voltage to cause them to accept current. Warm batteries will accept less voltage without causing overcharging.

4. After starting the battery on charge and periodically during the charging process, the battery should be cheeked to assure that it is not
overcharging. Overcharging can be identified by excessive battery case temperature and electrolyte boiling or bubbling (or spewing out the
vents).

^ Battery case temperatures of about 125~F is the maximum which should be allowed. Check by hand feel and reduce the charge rate if
high temperatures are found.
^ Excessive electrolyte bubbling or boiling indicates that the charge voltage is too high and that the battery is being forced to accept too
much current. Turn down the charge rate if high temperatures are found.

^ A battery with an internally shorted cell will show signs of overcharging at normally acceptable voltages. If charge voltages of around
13 volts result in overcharging (on a battery at room temperature or cooler), disconnect the battery and check the voltage. Batteries
with internal shorts will exhibit a drop in voltage over time. Batteries with internal shorts should be scrapped.
Technical Service Bulletin # 99-06-03-012 Date: 991201

Battery - Testing & Replacement


File In Section: 06 - Engine/Propulsion System

Bulletin No.: 99-06-03-012

Date: December, 1999

INFORMATION

Subject:
Battery Testing and Replacement

Models:
1997-2000 Passenger Cars and Trucks

This bulletin is being revised to update model year information, warranty information pertaining to claim submission for Cadillac Roadside Service,
terminal/connector leakage and also repair order and warranty claim requirements as they relate to the codes generated by the Midtronics tester.
Please discard Corporate Bulletin Number 83-64-17 (Section 6 - Engine).

Important:
The Midtronics Micro 410 Battery Tester should be used prior to any battery replacement for a no-start condition (unless physical damage is
found). The tester generates a 7-digit code which must be recorded on the repair order and also in the COMMENTS section of the claim
submission. Claims submitted without this information will be subject to review and possibly subsequent debit.

Adhering to published battery testing procedures and subsequent recording on the repair order and claims COMMENTS section, will help ensure
our customers receive an enhanced service experience and improve the efficiencies of the battery diagnosis process. The Midtronics Micro 410
Battery Tester, J 42000 uses conductance technology instead of traditional load testing. The tester allows you to test most batteries that are partially
discharged without first performing the time consuming charging and load testing procedure. The tester helps quickly identify batteries that are
serviceable and can be charged.

Battery testing can be performed in the vehicle at the battery terminals only. Do not test at remote battery terminals. If you cannot access the battery
terminals, remove the battery and test the battery out of the vehicle. As with any electrical test, a good connection is very important to battery
testing. If the test results indicate a bad battery, or if the results are inconclusive, do the following:

1. Disconnect the battery cables.


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 326
Chevrolet Venture V6-3.4L VIN E 2651

2. Clean the battery terminals.

3. Use the terminal adapters & re-test the battery.

Following the above procedure will eliminate battery replacement due to poor battery connections. The Midtronics Micro 410 helps identify and
correct battery problems. However, it is not capable of testing the generator, charging system or performing parasitic load tests. Refer to the
appropriate Service Manual for the correct tools and test procedures to diagnose other electrical system symptoms.

Battery Test Procedure

Review the following instructions before using the tester.

Caution:
Batteries produce explosive gases, contain corrosive acid and supply levels of electrical current high enough to cause burns. Therefore, to
reduce the risk of personal injury when working near a battery:

^ Always shield your eyes and avoid leaning over the battery whenever possible.

^ Do not expose the battery to open flames or sparks.

^ Do not allow the battery electrolyte to contact the eyes or the skin. Flush immediately and thoroughly any contacted areas with water and get
medical help.

Test the battery with the J 42000 Battery Tester, using the following procedure:

^ Inspect the battery for evidence of physical damage. If damage is found, replace the battery. If no damage is found, proceed to the next step.

^ Is the hydrometer eye yellow? If yellow, tap the hydrometer lightly with the handle of a small screwdriver. Did the color change? If no, replace
the battery. If yes, continue with the procedure.

^ Inspect for loose battery cables. Attempt to rotate the battery cable end. Properly torqued battery cables will have a break-away torque
requirement of 15 N.m (10 lb ft). If the bolt is tight and the end rotates, it may be due to the following conditions:

- The attaching bolt may be too long.

- There may be foreign material lodged in the battery bolt hole.

- The battery cable end may be damaged.

^ Install the J 42000 Battery Tester. Follow the directions supplied with the tester. When testing (with the battery cables still connected to the
battery), rock the J 42000 Battery Tester clips back and forth on the terminal bolt to cut through any coating or oxidation that may be present on
the bolt.

^ If it is uncertain that correct connections can be made to the battery terminal bolts in the vehicle, perform the following steps:

1. Disconnect the battery cables.

2. Install the test adapters on the terminals.

3. Follow the instructions for testing batteries outside of the vehicle.

^ If a REPLACE BATTERY result is obtained for a battery tested in the vehicle with the battery cables connected, perform the following steps:

1. Disconnect the battery cables.

2. Install the approved adapters.

3. Follow the instructions for testing the battery outside of the vehicle.

4. Replace the battery only if the second test shows a REPLACE BATTERY result.

For warranty purposes, record the test code from the second test.

^ Use the approved terminal adapters. Do not use common bolts or a combination of bolts, nuts and washers as adapters when testing the battery.
Use the test adapters that are provided with the J 42000 tester or GM P/N 12303040 terminal adapters. If the adapters that are provided with the
J 42000 require replacement, only use adapters with GM P/N 12303040. Any other adapters may not contact the correct areas of the battery
terminal, causing resistance that may result in an invalid battery test result.

^ In order to test top terminal, threaded stud batteries outside of the vehicle, use GM P/N 12303040 adapters. Do not connect the tester to the
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 327
Chevrolet Venture V6-3.4L VIN E 2652
threaded terminals without using the adapters.

Parts Information

Part Number Description

12303040 Terminal Adapter

Parts are currently available from GMSPO.

Warranty Information

Effective immediately, battery failures resulting from terminal/connector leakage are to be claimed using failure code "6J" to better assist
engineering with product analysis.

Battery failures, where other than leakage occurs, should continue the use of the tester and reporting of the tester codes on the warranty claim.

Cadillac Roadside Service

Because Cadillac Roadside technicians (during a roadside repair) cannot test batteries, use the following procedure when a battery is replaced on a
roadside visit:

Important:
Normal published battery testing procedures should be followed after returning to the dealership.

^ The technician should take the battery back to the dealership and perform a Midtronics test.

^ The code should be included in the comment section of the warranty claim when submitted to WINS.

^ If the battery is found to be good, note the code in the comment section of the claim, followed by the verbiage BATTERY GOOD -
ROADSIDE REPAIR.
Technical Service Bulletin # 00-06-03-003 Date: 000501

Battery - Testing and Replacement


File In Section: 06 - Engine/Propulsion System

Bulletin No.: 00-06-03-003

Date: May, 2000

INFORMATION

Subject:
Battery Testing and Replacement

Models:
1997-2001 Passenger Cars and Trucks (Except 2001 Chevrolet Corvette)

This bulletin is being issued to provide additional information to Corporate Bulletin Number 99-06-03-012, issued December, 1999. It does not
supersede that bulletin.

In a continuing effort to improve battery quality in our products, General Motors extensively monitors battery warranty claim information
submitted by dealers. It has become apparent that although many dealers are following the procedures as listed in Corporate Bulletin Number
99-06-03-012, some dealers are not adhering to the stated policy. Proper information is critical to quality improvements. The following are several
points regarding the testing procedure that are critical to providing correct information.

^ The correct CCA rating must be entered in the Midtronics tester.

^ The seven-digit Midtronics tester code is a critical piece of information. The procedure states that if the battery fails the "In Vehicle" test, the
technician must disconnect the battery cables. (Do not remove the battery from the vehicle at this time.) Install the terminal adapters and re-test
the battery using the tester's "Out of Vehicle" test. Replace the battery only if the second test shows a REPLACE BATTERY or BAD CELL
result. The test code from the SECOND TEST must be entered in the comments section of the warranty claim.

Important:
Failure to provide the Midtronics "Out of Vehicle" test code on the warranty claim may subject the claim to rejection.

^ Leaking batteries are to be claimed using failure code "6J" and do not require a Midtronics test code.

^ If a battery has leaked and has soaked the battery insulator blanket, a new blanket must be installed on the new battery.
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 328
Chevrolet Venture V6-3.4L VIN E 2653

Refer to Corporate Bulletin Number 99-06-03-012 for the correct Cadillac Roadside Service claim procedures.

DisclaimerTechnical Service Bulletin # 02-06-03-010A Date: 040702

Battery - Parasitic Drain


Bulletin No.: 02-06-03-010A

Date: July 02, 2004

INFORMATION

Subject:
Battery Parasitic Drain

Models:
2005 and Prior Passenger Cars and Trucks
2003-2005 Isuzu Light Duty Trucks

Supercede:

This bulletin is being revised to add the 2004 and 2005 model years. Please discard Corporate Bulletin Number 02-06-03-010 (Section 06 -
Engine).

In automotive terms, a parasitic drain is an electrical load that draws current from the battery when the ignition is turned off. Some devices, such as
the PCM and the radio memory are intended to draw a very small amount continuously. These draws are measured in milliamps (mA).

In normal use, parasitic drains aren't usually cause for concern, because the battery is replenished each time the vehicle is driven. But, in long-term
parking situations, parasitic drains may discharge the battery enough to cause a no-start condition. New vehicles in dealer stock and airport
long-term parking are two such situations.

An abnormal parasitic drain could be a glovebox or luggage compartment light that remains on but undetected. Or an electronic component may
malfunction and cause a parasitic drain that is larger than normal specification.

Parasitic Drains and On-the-Lot Battery Discharge

Important:
In most cases of discharged batteries in low-age, low-mileage vehicles, proper charging procedures with approved charging equipment is the
only repair necessary.

Here are some rules of thumb that might help relate parasitic drains to how long a battery would last on a parked vehicle. The Reserve Capacity
(RC) rating multiplied by 0.6 gives the approximate available ampere-hours (AH) from full charge to complete rundown. Somewhere between full
charge and complete rundown, the battery will reach a point at which it can no longer start the engine, although it may still operate some of the
electrical accessories.

Using up about 40% of the total available AH will usually take a fully-charged battery to a no-start condition at moderate temperatures of 25°C (77
°F). Put another way, for a typical battery in a storage situation, depleting the available AH by 20 to 30 AH will result in a no-start condition.

Important:
If the battery begins storage at 90% of full charge, reduce the available AH accordingly.

The recommendation for maximum parasitic drain is around 30 mA (0.030 amp). A typical drain today actually falls into the 7-12 mA range, even
though some vehicles do approach the maximum. Multiply the drain (in amps) by the time (in hours) the battery sits without being recharged. The
result is the amount of AH consumed by the parasitic drain. The actual drain may be small, but over time the battery grows steadily weaker.

Here's an example: a vehicle with a 30 mA drain and a fully-charged 70 RC battery will last 23 days. But if that battery is at only 65% of full
charge (green dot barely visible), it is going to last only 15 days before causing a no-start.

Effects of Temperature on a Standing Battery

The parasitic drain will be fairly constant over a range of temperatures. The important temperature is that of the vehicle at the time a start is
attempted. Colder temperature raises the threshold of a no-start by increasing the residual power needed. When the temperature falls to 0°C (32°F),
the battery will be able to put out only about 85% of its normally available starting power, and the engine may need as much as 165% of the usual
power to start.
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 329
Chevrolet Venture V6-3.4L VIN E 2654

The combined effect of these two factors is to reduce the number of days the battery can stand with a parasitic drain. At 0°C (32°F), the battery can
stand only half as long as it could at 25°C (77°F). And at -19°C (0°F), the standing days are reduced to one-fourth.

Temperatures above the moderate climate of 25°C (77°F) increase the battery's internal self discharge. If the battery is in a locale where the
temperature is averaging 32°C (90°F), an additional 5% to 10% of the available ampere-hours will be lost in a month due to self-discharge within
the battery. At temperatures below the moderate range, self-discharge will be low enough to be negligible compared to the parasitic loss.

What the Policies and Procedures Manual Says About Parasitic Drains

Because determining how long a battery may last in a storage situation is not precise, the P & P manual provides a clear-cut policy, excerpted here.

"Discharged batteries can freeze at temperatures as high as 0°C (32°F), causing permanent damage. Other permanent damage may result from
allowing batteries to stand discharged for extended periods."

"To alleviate this condition, the negative battery cable should be disconnected on vehicles which are not going to be in service within a 20 day
period, beginning from the time the vehicle is shipped. If this is not possible, batteries should be recharged periodically, every 20-45 days, until the
green eye is visible."

"Disconnected batteries will slowly discharge, especially with higher temperatures; therefore, even disconnected batteries should be checked every
four months and recharged if necessary."

"Vehicles on display are subject to battery discharge due to drains from courtesy lights and other accessories. Provision to maintain battery state of
charge for these vehicles will be necessary."

Consult your P & P manual for full details.

Tracking Down the Source of a Parasitic Load

If the battery in a vehicle becomes discharged in a shorter time than described earlier, the vehicle may have an out-of-specification parasitic load.
Refer to Service Information (SI) for procedures for locating parasitic drains. Follow these steps:

1. Build the vehicle.

2. Select the Engine section.

3. Select the Engine Electrical sub-section.

4. Select Diagnostic Information and Procedures.

5. Select Battery Electrical Drain/Parasitic Load Test.

You will need the J 38758 Parasitic Draw Test Switch and a digital multimeter set to the 10A scale.

Important:
Read the procedure and follow the steps exactly as described in SI. The following is a summary, not the complete procedure.

The test switch permits you to place an ammeter in series with the battery negative cable. Before performing the test, the engine must be run and all
accessories must be operated as instructed. After shutting the ignition off, turn the test switch off. Now, all the current being used by the vehicle is
shunted through the ammeter where it is measured. If the reading is out of specification, the procedure explains how to pinpoint the cause.

A Final Word About Battery Testing

Your dealership has an essential tool, the Midtronics Micro 410 Battery Tester, J 42000. Use it to quickly identify batteries that are serviceable and
can be charged. Refer to Corporate Bulletin Number 02-06-03-006A for more information about this tool.

DisclaimerTechnical Service Bulletin # 99-06-03-011 Date: 991001

Warranty - Generator Replacement


File In Section: 06 - Engine/Propulsion System

Bulletin No.: 99-06-03-011


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 330
Chevrolet Venture V6-3.4L VIN E 2655

Date: October, 1999

Subject:
CS-144 Generator Replacement

Models:
1998-2000 Passenger Cars and Trucks

Beginning with the 1998 model year, General Motors stopped releasing internal repair components for the CS-144 Generator.

GM warranty procedures require the replacement of the CS-144 generator. The generator unit repair procedures found in the past model Service
Manuals should not be used.

Use of non-GM repair parts for warranty repairs is not approved or recommended. Therefore, warranty labor claims for CS-144 generator rebuilds
in the field for 1998 and newer vehicles will not be accepted.

Service parts which may be available through GM for past model years, which appear to fit, should not be used. The use of correct parts is essential
for proper performance of the generator.

This policy change was instituted by GM to provide the best service and warranty experience for our customers.
Technical Service Bulletin # 01-06-03-005 Date: 010501

Interior/Exterior Lamps - Flicker


File In Section: 06 - Engine/Propulsion System

Bulletin No.: 01-06-03-005

Date: May, 2001

TECHNICAL

Subject:
Interior and Exterior Lamps Vary in Brightness
(Replace Generator Voltage Regulator Ground Screw)

Models:

2000-2001 Chevrolet Impala (With 3800 Engine and Police or Taxi Package)
2000-2001 Chevrolet Venture
2000-2001 Oldsmobile Silhouette
2000-2001 Pontiac Montana

Condition

Some customers may comment that the interior and/or the exterior lamps vary in intensity (flicker).

Correction
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 331
Chevrolet Venture V6-3.4L VIN E 2656

Replace the voltage regulator attaching screw with the screw and washer from the service kit following the procedure outlined.

1. Disconnect the battery cable.

2. Remove the wiper module cover (U-Van).

3. Remove the voltage regulator ground screw (1). (This is the recessed screw located 1/3 of the way from the large battery cable attachment to
the generator harness.) Use a stubby # 2 Phillips screwdriver to break it loose and then loosen the screw with a small pocket screwdriver. The
screw may hang up on the plastic cover on the rear of the generator. If this happens, use a pocket screwdriver inserted between the screw and
the cover. The screw will pop out when a little sideways pressure is applied.

4. Install the screw and washer from the kit through the voltage regulator and into the generator case.

5. Tighten the screw securely.

6. Replace the wiper module cover.

7. Reconnect the battery cable.

Tighten

Tighten the cable to 15 N.m (11 lb ft).

Parts Information

Parts are expected to be available from GMSPO, 5/16/01.

Warranty Information

For vehicles repaired under warranty, use the table.


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 332
Chevrolet Venture V6-3.4L VIN E 2657

DisclaimerTechnical Service Bulletin # 99-06-03-010A Date: 010601

PCM/BCM Replacement - DTC's B001/B1271/B1780 Set


File In Section: 06 - Engine/Propulsion System

Bulletin No.: 99-06-03-010A

Date: June, 2001

INFORMATION

Subject:
DTCs B1001, B1271 or B1780 Set When Replacing/Reprogramming Other Modules

Models:
1999-2002 All Passenger Cars and Trucks
With Class 2 Serial Data Communication Between Modules

This bulletin is being revised to add model years. Please discard Corporate Bulletin Number 99-06-03-010 (Section 06 - Engine/propulsion
System).

Class 2 Serial Data Communication allows control modules (i.e. the Powertrain Control Module (PCM), the Body Control Module (BCM), the
Dash Integration Module (DIM), the Instrument Panel Cluster (IPC), the radio, the Heating, Ventilation and Air Conditioning (HVAC) Controller,
and the Sensing and Diagnostic Module (SDM) to exchange information. This information may be operational information or identification
information. Among the identification information exchanged and compared within these modules is the Vehicle Identification Number (VIN).
Typically, the PCM broadcasts a portion of the VIN, while another module broadcasts another portion of the VIN. This information is compared by
the SDM in order to ensure installation is in the correct vehicle. When the broadcast VIN does not match the VIN stored within the SDM, the
following actions occur:

^ DTC B1001 Option Configuration Error is set and deployment of the airbags is inhibited.

^ The VIN information is also used by the radio in order to prevent theft. When the broadcast VIN does not match the VIN stored within the
radio, a DTC B1271 ora DTC B1780 Theft Locked is set and the radio is inoperative.

This situation may occur when a vehicle is being repaired. When a PCM or a body control type module is replaced, the VIN information must be
programmed into the replaced (new) control module. A module which has had VIN information entered into it (for example, one taken from
another vehicle) cannot be reprogrammed. VIN information can only be entered into new modules. The ignition must be ON in order to program
the control module. Since the VIN information is broadcast when the ignition goes to ON from any other ignition switch position, DTCs may be set
in the SDM and/or the radio. Therefore, always follow the specified control module replacement procedures.

1. After completing the repair, turn OFF the ignition for at least 30 seconds.

2. Turn ON the ignition and check for DTCs using a scan tool.

If DTCs B1001, B1271, or B178C are present with a history status, DO NOT REPLACE THE SDM OR THE RADIO.

3. Clear the DTCs from all modules using the scan tool. The SDM and/or the radio should then operate properly.

4. Ensure the proper operation of the SDM by turning OFF the ignition and then turning ON the ignition. The air bag warning indicator should
flash seven times and then go OFF.

Refer to Corporate Bulletin Number 99-09-41-001 for additional information regarding proper reprogramming of the new/replaced module.

Clearing codes from the other modules is part of the replacement and reprogramming procedure for the replaced module. The repair is not complete
unless all codes have been cleared from all modules.

DO NOT SUBMIT CLAIMS FOR OTHER MODULE REPLACEMENTS OR REPROGRAMMING.


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 333
Chevrolet Venture V6-3.4L VIN E 2658

DISCLAIMERTechnical Service Bulletin # 99-06-04-053 Date: 991101

PROM - Powertrain Control Module Reprogramming


File In Section: 06 - Engine/Propulsion System

Bulletin No.: 99-06-04-053

Date: November, 1999

INFORMATION

Subject:
Powertrain Control Module (PCM) Reprogramming
(Do Not Reprogram Using the Same Download Files as Those Already Present in The Control Module)

Models:
1990-2000 Passenger Cars and Trucks with Reprogrammable PCM

It is strongly recommended to NOT reinstall the same software and/or calibration download file(s) into the powertrain control module as those that
are already present in the PCM. There is no technical reason that the download files inside the PCM would ever become corrupted after the control
module had previously been successfully programmed. A P0601 (Control Module Read Only Memory) Diagnostic Trouble Code would set in
memory and the MIL would be illuminated if the controller memory became corrupted.

The Techline Information System 2000 (TIS 2000) PC, combined with vehicle information gained through the Tech 2, can determine when an
attempt to reprogram a PCM using the same download files (as those already in the control module) is being requested. If this is attempted, the TIS
2000 PC currently displays the following message:

Notice:
THE CALIBRATION SELECTED IS THE CURRENT CALIBRATION IN THE CONTROL MODULE. PROGRAMMING WITH THE
SAME DOWNLOAD FILES IS NOT AN EFFECTIVE REPAIR. SELECT ( YES ) TO CONTINUE PROGRAMMING THE CONTROL
MODULE,OR ( NO ) TO CANCEL.

Effective in the first quarter of 2000, the TIS 2000 PC will indicate:

Important:
THE CALIBRATION SELECTED IS ALREADY THE CURRENT CALIBRATION IN THE CONTROL MODULE. REPROGRAMMING
WITH THE SAME DOWNLOAD FILE IS NOT ALLOWED.

Certain learned values, such as: (but not limited to)

^ fuel trim (previously known as block learn memory),

^ IAC learned position in various park/neutral and air conditioning on/off combinations,

^ certain OBDII diagnostic thresholds,

^ automatic transmission shift adapts

will revert back to their unlearned starting point values after a reprogramming event occurs.

It is feasible that the engine or transmission might temporarily operate differently after a reprogramming event, until these values are re-learned.
Relearning occurs while operating the vehicle through normal driving routines. If the same download files are simply reinstalled, any changes
noticed in engine operation will likely disappear in a short amount of time and/or driving distance.

Reprogramming the control module with the same download files that already exist in the module will only accomplish a warranty claim for a
non-effective repair, and a likely comeback.
Technical Service Bulletin # NHTSA99V268000 Date: 991011

Recall 99V268000: Fuel Tank Inspection/Replacement


NHTSA CAMPAIGN ID Number: 99V268000
Component: FUEL: VEHICLE CRASH, CUT OFF SYSTEM (5-94)
Manufacturer: GENERAL MOTORS CORP.
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 334
Chevrolet Venture V6-3.4L VIN E 2659

Year: 2000
Make: CHEVROLET TRUCK, PONTIAC TRUCK, OLDSMOBILE TRUCK
Model: VENTURE, MONTANA, SILHOUETTE
YEAR Of Recall: '99
Type of Report: Vehicle
Potential Number of Units Affected: 235

Summary:

Vehicle Description: Minivans with extended wheelbase.


Some of these vehicles have inoperative fuel tank rollover
valves and fuel leakage would exceed the permissible
amount in a rollover test. This does not comply with the
requirements of FMVSS No. 301, "Fuel system Integrity."

In a vehicle rollover accident, if an ignition source is


present, a fire could result.

Dealers will inspect the vehicle to locate and replace those


fuel tanks that could have inoperative rollover valves.

Owner notification began October 11, 1999. Owners who take


their vehicles to an authorized dealer on an agreed upon
service date and do not receive the free remedy within a
reasonable time should contact Chevrolet at 1-800-222-102 or
Pontiac at 1-800-762-2737, or Oldsmobile at 1-800-442-6537.
Also contact the National Highway Safety Administration's
Auto Safety Hotline at 1-888-DASH-2-DOT (1-888-327-4236). Technical Service Bulletin # 04-08-48-001B Date: 050628

A/C - Broken Rear Window Defogger Grid Detection


Bulletin No.: 04-08-48-001B

Date: June 28, 2005

INFORMATION

Subject:
Rear Window Defogger - Broken Heating Grid Detection Method

Models:
2006 and Prior Passenger Cars and Light Duty Trucks (Including Saturn)
2003-2006 HUMMER H2
2006 HUMMER H3

Supercede:

This bulletin is being revised to add the 2006 model year and additional models. Please discard Corporate Bulletin Number 04-08-48-001A
(Section 08 - Body and Accessories).

The addition of vertical grid lines to the heated back window defogger circuits has made it difficult to detect broken defogger grid lines. In the past,
it was a simple matter to use a voltmeter to check the continuity of each grid line in order to locate a non-functional line. Some new design back
windows have two vertical grid lines that connect all of the horizontal grid lines together, thereby providing alternate routes for the electrical
current to follow. This makes the old test method ineffective. If the vehicle does not have the vertical lines, the old (line-by-line) test methods can
be used.

Materials Required

^ Permatex(R) Quick Grid, GM P/N 12346001, or equivalent

^ A small ball of fine steel wool Type 00, or

^ Optional - A strip of liquid crystal heat sensitive paper, 51 mm x 305 mm (2 in x 12 in) or similar size (Contact Edmund Scientific at
800-728-6999 for part number CR30723-70 or go to www.scientificsonline.com), or

^ Optional-A portable infrared thermometer, GE-46819, available from Kent-Moore (1-800-345-2233), or equivalent.

Correction
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 335
Chevrolet Venture V6-3.4L VIN E 2660

There are three distinct zones across the back window that must be checked. They are:

^ the driver's side outboard of the two vertical lines

^ the passenger side outboard of the two vertical lines

^ the central zone that falls between the two vertical lines

To detect a broken grid line in any of the above three zones and to isolate the exact location of the break, perform the following steps:

Caution:
^ Approved safety glasses and gloves should be worn when performing this procedure to reduce the chance of personal injury.

^ Cover the rear shelf area to prevent damage to the interior trim material.

1. Start the engine and turn on the back window defogger.

2. Take the ball of fine steel wool and twist one end to a point. Move the point slowly across each grid line. Be sure to start at the far side of the
zone and move it to the opposite side of the zone. When you bridge the grid line break with the steel wool, you will see a small spark. Repeat
the test over the same area to be sure you have accurately located the break. Mark the exact location of the grid line break. Repeat this portion
of the test for each grid line. If you do not see a spark at any point, it is possible that there are two breaks in the same line and zone. Close
visual inspection using a magnifying glass may be the only way to locate breaks in this case.

3. The following are provided as an alternative way to detect a non-functional grid line. If available, use in addition to the steel wool.

3.1. Method using liquid crystal heat sensitive paper:

Important:
The first part of the test must be completed quickly before the entire surface of the back window becomes warm.

3.1.1. From outside the vehicle, place the heat sensitive paper (dull surface in contact with the glass) against the top driver side grid line. Start
the engine and turn on the back window defogger. A distinct color change will take place at each conductive grid line. Repeat for the
bottom grid lines until they have all been checked in the driver side zone.

3.1.2. Repeat the process for the passenger side and center area zones.

3.1.3. If no color change is noted for a grid line, place a crayon or china marker check mark beside it. Mark each grid line in the zone where it
is non-conductive and, therefore, not heating up. More than one broken grid line may be found.

3.2. Method using portable infrared thermometer:

3.2.1. Start the engine and turn on the rear back window defogger.

3.2.2. From inside the vehicle, start at the top driver side grid line and slowly run the portable infrared thermometer vertically down the rear
window contacting each grid line. You should be able to see a district variation in temperature readings.

3.2.3. Mark each grid line in the zone where it is non-conductive and, therefore, not heating up. More than one broken grid line may be
found.

3.2.4. Repeat the process for the passenger side and center area zones.

4. Use Permatex(R) Quick Grid, GM P/N 12346001, or equivalent, to repair each broken grid line. Follow the manufacturer's instructions.

5. Wait 24 hours before turning the defogger on, or the repair can be fast cured using a heat gun, 260 °C - 371°C (500°F - 700°F). Hold the heat
gun within 25 - 51 mm (1-2 in) from the repair point for 2 to 3 minutes.

6. Recheck the grid line with the heat sensitive paper or portable infrared thermometer to ensure that the line is now functional and that the
repair was successful.

DisclaimerTechnical Service Bulletin # 01-08-44-006A Date: 010601

Audio System - Clearing `CLN' Message From Display


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 336
Chevrolet Venture V6-3.4L VIN E 2661
File In Section: 08 - Body and Accessories

Bulletin No.: 01-08-44-006A

Date: June, 2001

INFORMATION

Subject:
Cleaning the Cassette Tape Player and Clearing the CLN Message from the Radio Display

Models:
1996-2002 Chevrolet and GMC Truck Models
With Remote Cassette Tape Player (RP0 UP0)

This bulletin is being revised to include additional model years and models, parts information, and to provide a procedure for cleaning the cassette
tape player and resetting the CLN indicator on the radio display. Please discard Corporate Bulletin Number 01-08-44-006 (Section 08 - Body and
Accessories).

When the CLN message appears on the audio system, it indicates that the cassette tape player requires cleaning. Customers should follow the listed
instructions. The recommended cleaning method for the remote cassette player is to use a scrubbing action, non-abrasive cleaning cassette, GM P/N
12344789. The cleaning cassette scrubs the tape head as the hubs of the cleaner cassette turn.

Use the following procedure to clean the remote cassette player and reset the CLN indicator on the radio.

1. With the radio ON, insert the recommended cleaning cassette.

2. After a few seconds, the cleaning cassette may eject because it may appear to the player as a cassette with a broken tape. If ejection occurs,
reinsert the cleaning cassette. Continue this process three or four times until the cleaning cassette is engaged for the time recommended by the
cleaning cassette instructions.

3. Eject the cleaning cassette if the cassette does not eject on its own.

4. Press and hold the RECALL button on the radio until CLN appears on the radio display. While still pressing the radio RECALL button, press
EJECT on the remote player. Release both buttons when the radio display indicates that the CLN indicator timer has been reset.

Parts Information

Parts are currently available from GMSPO.

DISCLAIMERTechnical Service Bulletin # 01-08-46-004A Date: 050308

OnStar(R)/Cell Phone - Integration


Bulletin No.: 01-08-46-004A

Date: March 08, 2005

INFORMATION

Subject:
Vehicle Integration of Cellular Phones and Normal Operating Characteristics

Models:
2002 and Prior Passenger Cars and Trucks

Supercede:

This bulletin is being issued to cancel Corporate Bulletin Number 01-08-46-004. Please discard all copies of Corporate Bulletin Number
01-08-46-004 (Section 08 - Body and Accessories).
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 337
Chevrolet Venture V6-3.4L VIN E 2662

This bulletin effectively cancels Corporate Bulletin Number 01-08-46-004. OnStar(R) no longer offers cellular phones as part of the OnStar(R)
system.

DisclaimerTechnical Service Bulletin # 02-08-46-004A Date: 060411

Cell Phone - Error Messages, Bulletin Cancellation


Bulletin No.: 02-08-46-004A

Date: April 11, 2006

INFORMATION

Subject:
Cellular Error Messages Received When Trying to Connect to OnStar(R)

Models:
2000-2002 Passenger Cars and Light Duty Trucks

with Factory-Installed OnStar(R)

Supercede:

This bulletin is being revised to cancel this bulletin. The Subject information is addressed in Corporate Bulletin Number 03-08-46-004B. Please
discard Corporate Bulletin Number 02-08-46-004 (Section 08 - Body & Accessories).

Please reference Corporate Bulletin Number 03-08-46-004B for the Subject information.

DisclaimerTechnical Service Bulletin # 99-08-42-009 Date: 991101

IP Dimmer Control - Proper Setting


File In Section: 08 - Body and Accessories

Bulletin No.: 99-08-42-009

Date: November, 1999

INFORMATION

Subject:
Proper Setting of I/P Dimmer Control to View PRNDL Display with Automatic Headlamp Control

Models:
2000 and Prior All Passenger Cars and Trucks
With Automatic Headlamp Control and Electronic PRNDL Display

Under certain conditions, if the instrument panel dimmer control is turned relatively low, the PRNDL will not be visible until the automatic
headlamp control turns the headlamps off and the daytime running lamps (DRL) are turned back on. Such a condition may be if the vehicle is first
started in an environment where the headlamp control turns on the headlamps and then the vehicle is driven out into a brighter environment (for
example, when a vehicle is backed out of a dark garage into the bright sunlight).

This condition is normal and any repair attempt will not be successful. Demonstrate this condition to the customer using the service lane and then
turn the instrument panel dimmer control to a higher setting. This will enable the driver to see the PRNDL display
Technical Service Bulletin # 04-05-23-002A Date: 050804
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 338
Chevrolet Venture V6-3.4L VIN E 2663

Brakes - Minimum Allowable Rotor Thickness


Bulletin No.: 04-05-23-002A

Date: August 04, 2005

INFORMATION

Subject:
Brake Rotor Minimum Allowable Thickness After Refinish Specification Correction

Models:
2001-2004 Buick Century, Regal
2002-2004 Buick Rendezvous
1997-2004 Chevrolet Venture
2001-2004 Chevrolet Impala, Monte Carlo
1997-2004 Oldsmobile Silhouette
2001-2002 Oldsmobile Intrigue
1997-1998 Pontiac Trans Sport
1999-2004 Pontiac Montana
2001-2004 Pontiac Aztek, Grand Prix

Supercede:

This bulletin is being revised to add models and model years. Please discard Corporate Bulletin Number 04-05-23-002 (Section 05 - Brakes).

The current "Rotor Minimum Allowable Thickness After Refinish Specification" found in past Service Manual information is incorrect.

The correct Minimum Allowable Thickness After Refinish specification shown in the table should be used to determine the service life of the rotor.

This information has been updated within SI. If you are using a paper version of this Service Manual, please make a reference to this bulletin on the
affected page.

DisclaimerTechnical Service Bulletin # 00-08-42-003 Date: 000601

Headlamp - Capsule Now Available


File In Section: 08 - Body and Accessories

Bulletin No.: 00-08-42-003

Date: June, 2000

INFORMATION

Subject:
Headlamp Capsule Availability
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 339
Chevrolet Venture V6-3.4L VIN E 2664

Models:
1997-2000 Chevrolet Venture
1997-2000 Oldsmobile Silhouette
1997-2000 Pontiac Trans Sport

The headlamp capsules for the above vehicles can now be purchased separately from the mounting frame and aiming assembly. These capsules
come complete with a new bulb. If headlamp capsule replacement becomes necessary, use the following procedure:

1. Remove the one wing nut that secures the cornering lamp to the vehicle.

2. Remove the cornering lamp from the vehicle & disconnect the two electrical connectors.

3. Remove the two wing nuts that secure the headlamp to the vehicle.

4. Remove the headlamp from the vehicle and disconnect the electrical connector.

5. Remove the two 10 mm hex head screws and one 10 mm nut that attach the black frame to the headlamp.

6. Remove the two 5.5 mm hex head screws that attach the headlamp to the black frame.

7. Separate the headlamp from the frame.

8. Remove the two 7 mm hex head screws that attach the black horizontal aiming device to the headlamp.

9. Transfer the horizontal aiming device and two screws to the NEW headlamp.

Tighten
Tighten the screws to 2 N.m (18 lb in).

10. Remove the two 7 mm hex head screws that attach the black pivot to the headlamp.

11. Transfer the black pivot and two screws to the NEW headlamp.

Tighten
Tighten the screws to 2 N.m (18 lb in).

12. Install the black frame to the NEW headlamp capsule.

13. Install the two 5.5 mm hex head screws.

Tighten
Tighten the screws to 2 N.m (18 lb in).

14. Install the two 10 mm hex head screws.

Tighten
Tighten the screws to 5 N.m (45 lb in).

15. Install the one 10 mm hex head nut.

Tighten
Tighten the nut to 6 N.m (55 lb in).

16. Connect the electrical connector to the NEW headlamp bulb and install the headlamp on the vehicle.

17. Install the two wing nuts and hand tighten.

18. Connect the two electrical connectors to the cornering lamp and install the lamp on the vehicle.

19. Install the wing nut and hand tighten.

20. Inspect the headlamp for proper operation and aim.


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 340
Chevrolet Venture V6-3.4L VIN E 2665

Parts Information

Parts are currently available from GMSPO.

Warranty Information

For vehicles repaired under warranty, use the table.

DisclaimerTechnical Service Bulletin # 03-02-32-049 Date: 031029

Steering - New Outer Tie Rods/Replacement Procedure


Bulletin No.: 03-02-32-049

Date: October 29, 2003

INFORMATION

Subject:

Release Of New Outer Tie Rod Ends For Service

Models:
1997-2001 Buick Century
1997-2001 Buick Regal
2000-2003 Buick LeSabre, Park Avenue
2002-2003 Buick Rendezvous
1997-2003 Cadillac Seville
2000-2003 Cadillac DeVille
1997-2001 Chevrolet Venture (FWD)
1997-2003 Chevrolet Malibu
2000-2001 Chevrolet Impala, Monte Carlo
2002-2004 Chevrolet Venture (AWD)
1997-2001 Oldsmobile Silhouette (FWD)
1998-2001 Oldsmobile Intrigue
1999-2003 Oldsmobile Alero
2001-2003 Oldsmobile Aurora
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 341
Chevrolet Venture V6-3.4L VIN E 2666
2002-2004 Oldsmobile Silhouette (AWD)
1997-2001 Pontiac Grand Prix, Montana (FWD), Trans Sport (FWD)
1999-2003 Pontiac Grand Am
2000-2003 Pontiac Bonneville
2001-2003 Pontiac Aztek
2002-2004 Pontiac Montana (AWD)
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 342
Chevrolet Venture V6-3.4L VIN E 2667

Built Prior to VIN Breakpoint shown.

A new outer tie rod end service kit has been released. When replacing the outer tie rod ends, use the improved tie rod end service kit and modify the
knuckles. Follow the service procedure below.

Procedure

Important:
DO NOT USE the following outer tie rod end P/N's when servicing the above listed vehicles:

^ 26086579

^ 26086580

1. Raise and support the vehicle.

2. Remove the front tire and wheel assemblies.


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 343
Chevrolet Venture V6-3.4L VIN E 2668

3. Loosen the jam nut (2) on the inner tie rod assembly (1).

4. Remove and discard the prevailing torque nut from the outer tie rod assembly.

5. Using the J 24319-B, remove the outer tie rod assembly (2) from the steering knuckle (1).

6. While removing the outer tie rod end from the inner tie rod assembly, count the number of revolutions it takes to remove the outer tie rod
from the inner tie rod and record it. Discard the outer tie rod end.

Important:
When sanding the knuckle, DO NOT REMOVE excessive material from the knuckle. ONLY USE the emery cloth supplied in the service
kit.

7. Use the emery cloth supplied in the service kit to remove the sharp edge on the knuckle shown above. The graphic on the left shows the "
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 344
Chevrolet Venture V6-3.4L VIN E 2669
before sanding" knuckle and the exploded graphic on the right shows the "after sanded" knuckle.

8. Ensure that the sharp edge and the flashing on the knuckle are removed from the outer tie rod end boot/seal area.

9. Install the new outer tie rod end supplied in the service kit by screwing the outer tie rod end onto the inner tie rod end assembly. Turn the
outer tie rod end as many turns as it took to remove the old outer tie rod end from the inner tie rod end assembly.

10. Install the prevailing torque nut to the outer tie rod assembly.

Tighten

Tighten the prevailing torque nut to 30 N.m (22 lb ft). Tighten the prevailing torque nut an additional 115 degrees of rotation.

11. "Hand Tighten" the jam nut at this time.

12. Install the tire and wheel assembly.

13. Lower the vehicle.

14. Inspect the front toe and adjust if necessary.

15. Tighten the jam nut against the outer tie rod assembly.

Tighten

Tighten the jam nut to 68 N.m (50 lb ft).

Parts Information

Parts are currently available from GMSPO.

Warranty Information
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 345
Chevrolet Venture V6-3.4L VIN E 2670

For vehicles repaired under warranty, use the table.

Disclaimer
Technical Service Bulletin # 02-08-58-003 Date: 020601

Interior - Road Noise Heard From Behind Front Seats


File In Section: 08 - Body and Accessories

Bulletin No.: 02-08-58-003

Date: June, 2002

TECHNICAL

Subject:
Road Noise Heard Behind Front Seats (Seal Sheet Metal Seams)

Models:
1997-2002 Chevrolet Venture
1997-2002 Oldsmobile Silhouette
1997-2002 Pontiac TransSport, Montana

Condition

Some customers may comment that road noise can be heard coming from the area behind the front seats.

Cause

This condition may be caused by an open sheet metal seam in the metal support panel between the frame rail and the rocker panel.

Correction

1. Raise the vehicle on a hoist. Refer to Lifting and Jacking the Vehicle in the General Information Subsection of the Service Manual.

2. Locate the support panel between the underbody frame rail and the rocker panel. It is in the middle of the underbody of the vehicle just
behind the front doors. The support panels on both sides of the vehicle must be sealed.

3. Clean both the front and back sides of the support panel as required.
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 346
Chevrolet Venture V6-3.4L VIN E 2671

4. Apply Medium Body Seam Sealing Compound, P/N 12378500 (in Canada, P/N 10952233), to the front side of the support panel at the
locations shown by the arrows in the illustration. Use a small brush to force the sealer into the open seams and corners of the support panel.

5. Apply Medium Body Seam Sealing Compound, P/N 12378500 (in Canada, P/N 10952233), to the rear side of the support panel at the
locations shown by the arrows in the illustration. Use a small brush to work the sealer into the open seams and corners of the support panel.

6. Lower the vehicle


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 347
Chevrolet Venture V6-3.4L VIN E 2672

Parts Information

Parts are currently available from GMSPO.

Warranty Information

For vehicles repaired under warranty, use the table.

DISCLAIMER
Technical Service Bulletin # 02-08-67-006B Date: 030301

Body - Front/Rear Roof Rust Perforation


File In Section: 08 - Body and Accessories

Bulletin No.: 02-08-67-006B

Date: March, 2003

TECHNICAL

Subject:
Roof Perforation (Replace Roof)

Models:
1997-2003 Chevrolet Venture
1997-2003 Oldsmobile Silhouette
1997-2003 Pontiac TranSport/Montana

This bulletin is being revised to add another condition in the Labor Operation Warranty Table. Please discard Corporate Bulletin Number
02-08-67-006A (Section 08 - Body and Accessories).

Important:
Implementation of this service bulletin by "GM of Canada" dealers requires prior District Service Manager approval.

Condition

Some customers may comment that there is rust forming around the front or rear portion of the roof.

Cause

During production, the E-coating (ELPO primer) may have been missed in concealed areas of the front or rear portions of the outer roof panel.

Correction

Important:
Partial repairs to the roof panel are not permitted.

1. Remove the headliner. Refer to Headliner Replacement in the Interior Trim subsection of the Service Manual (SI document ID # 508247).
This document ID can only be found under 2003; however, this procedure covers 1997-2002 also.

2. Replace the roof. Refer to Roof Outer Replacement in the Collision Repair subsection of the Service Manual (SI document ID # 875050).
This document ID can only be found under 2003; however, this procedure covers 1997-2002 also.
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 348
Chevrolet Venture V6-3.4L VIN E 2673

Important:
Adhesive Bonding is the preferred installation method.

3. Reinstall the headliner. Refer to Headliner Replacement in the Interior Trim subsection of the Service Manual.

Parts Information

Parts are currently available from GMSPO.

Warranty Information

For vehicles repaired under warranty, use the table shown.

Disclaimer
Technical Service Bulletin # 02-08-58-005B Date: 050209

Body - Wind Noise From Windshield Base


Bulletin No.: 02-08-58-005B

Date: February 09, 2005

TECHNICAL

Subject:

Windnoise At Base Of Windshield (Seal Sheet Metal Seams)

Models:
2005 Buick Terraza
1997-2005 Chevrolet Venture
2005 Chevrolet Uplander
1997-2004 Oldsmobile Silhouette
1997-2004 Pontiac TransSport, Montana
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 349
Chevrolet Venture V6-3.4L VIN E 2674
2005 Pontiac Montana SV6
2005 Saturn Relay

Supercede:

This bulletin is being revised to add model years and models. Please discard Corporate Bulletin Number 02-08-58-005A (Section 08 - Body and
Accessories).

Condition

Some customers may comment on a Windnoise from the base of the windshield (right and/or left side). The concern is most apparent while driving
in a crosswind.

Cause

This condition may be caused by improperly sealed sheet metal seams in the cowl.

Correction

Apply seam sealer to the sheet metal seams just below the lower corners of the windshield.

1. Remove the air inlet grille. Refer to the Air Inlet Grille Panel Replacement procedure in the Body Front End Sub-section of the Service
Manual.

2. Locate the sheet metal seams at the base of the windshield on both sides of the cowl. Refer to the dotted line in the illustration above for the
location. Left side shown. Right side typical.

3. Apply Medium Body Seam Sealing Compound, P/N 12378500 (in Canada, P/N 10952233), or equivalent, as required, to the sheet metal
seams on both sides of the cowl.

4. Reinstall the air inlet grille. Refer to the Air Inlet Grille Panel Replacement procedure in the Body Front End Sub-section of the Service
Manual.

Parts Information
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 350
Chevrolet Venture V6-3.4L VIN E 2675

Parts are currently available from GMSPO.

Warranty Information

For vehicles repaired under warranty, use the table.

Important:
Saturn Retailers Only: Do NOT claim GM P/N 12378500. It will be necessary to sell Medium Body Seam Sealer to the CSO as "material" using
net item code "M". Claims received in the amount of $2.50 for this part will be accepted. Claims exceeding the amount of $2.50 will be returned
with the Return Reason 143 - Material/Reimbursement > Maximum Allowed.

DisclaimerTechnical Service Bulletin # 99-08-51-001A Date: 051121

Body - Paint-Less Dent Repair Recommendations


Bulletin No.: 99-08-51-001A

Date: November 21, 2005

INFORMATION

Subject:
Paint-less Dent Repair Process

Models:
2006 and Prior GM Passenger Cars and Trucks
2003-2006 HUMMER H2
2006 HUMMER H3
2005-2006 Saab 9-7X

with Steel Outer Body Panels

Supercede:

This bulletin is being revised to add model years, models and update the information. Please discard Corporate Bulletin Number 99-08-51-001
(Section 08 - Body and Accessories).

The process of removing dents from vehicles without painting has been around for many years. Over the past several years, General Motors has
evaluated many versions of this process. Most versions were found to be unacceptable because of the potential long-term durability concerns.
However, a new type of repair process has been identified. This process uses special tools requiring no drilling of holes or removal of vehicle
components for access. This process is appropriate for the majority of panels with reasonable access to the back side of the damaged area. The
special tools and procedures that have been developed will remove the dents while eliminating the need to fill, paint, or replace the panel. This type
of procedure has been thoroughly evaluated and the repaired parts were tested for negative impact. No negative impact was found.

Important:
The removal of structural components or drilling of holes in any panel is not recommended and may void the General Motors Corrosion
Warranty. Evaluating Damage

Appropriate uses for paint-less dent repair include the following conditions:

^ Dents with no broken paint on the surface. Be sure to inspect for cracks with a 4x magnifying glass.

^ Large or small dents, creases or buckles, small sharp dents and soft dents in body lines and contoured areas that allow reasonable access to the
back side of the damaged area.
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 351
Chevrolet Venture V6-3.4L VIN E 2676

^ Dents that do not require structural part removal.

Inappropriate uses for paint-less dent repair include the following situations:

^ Dents that include cracked paint.

^ Dents that require holes to be drilled.

^ Dents that require structural parts to be removed.

^ Sharp dents in contoured areas, dents on the edge of panels, or dents in zero-clearance areas.

Tools

Use tools that are high-quality, tempered steel with smooth polished, rounded tips. These will not damage the back side of the dented area.
Typically, these tools are shaped and bent in order to allow access to most areas of the vehicle without drilling holes in the body as well as provide
a clear view of the work area. Specialty lights are also used to highlight damaged areas.

DisclaimerTechnical Service Bulletin # 99-08-44-001B Date: 010301

Video Entertainment System - Exchange Program


File In Section: 08 - Body and Accessories

Bulletin No.: 99-08-44-001B

Date: March, 2001

EXCHANGE PROGRAM

Subject:
Video Entertainment System

Models:
2000-2001 Chevrolet Venture Warner Brothers Edition
1998-2001 Oldsmobile Silhouette Premiere
1999-2001 Pontiac Montana with RPO U42

This bulletin is being revised to add past model part numbers and to revise the claim system for specific components. Please discard Corporate
Bulletin Number 99-08-44-001A (Section 08 - Body and Accessories).

The following exchange program for the Video Cassette Player (VCP) and LCD Video Screen has been set-up for vehicles within the warranty
period. This exchange program must be utilized when the diagnostic procedures in the Service Manual or the Electronic Service Information lead
the technician to replacement of these units.

Dealers will no longer be required to obtain a case number from GM Technical Assistance to request a pre-exchange unit from Model Electronics
on the following part numbers:

Important:
The units shown should be ordered directly from Model Electronics at 1-800-433-9657.

Important:
When ordering units for crash, fire, theft, and flood damage, please notify Model Electronics to ship an OEM unit and not a remanufactured
part.
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 352
Chevrolet Venture V6-3.4L VIN E 2677

For all current components not listed above:

^ Call the Technical Assistance Center and request an exchange unit:

- USA: 1-877-446-8227
- Canada: 1-800-263-7740 (English) or 1-800-263-7960 (French)

^ A remanufactured unit will be shipped overnight to the dealership at no cost.

- The exchange unit will include a work order number. Please reference this number on the 1078A form (Notation Column).

- The dealership should include an ACD1078A form along with a copy of the repair order. Re-use the original shipping container.

- In the USA, ship the defective unit to:

Model Electronics
321 W. Route 59
Nanuet, NY 10954
1-800-433-9657

- In Canada, ship the defective unit to the AC Delco Superstore that shipped the replacement unit.

Important:
IF THE DEFECTIVE UNIT IS NOT RECEIVED WITHIN 10 DAYS, A CORE CHARGE WILL BE ASSESSED.

Important:
This exchange program is for warranted vehicles only. All units needed for non-warranty replacements must be ordered through GMSPO.

DISCLAIMER
Technical Service Bulletin # 01-08-46-001A Date: 050307

OnStar(R) - Configuration After Module Replacement


Bulletin No.: 01-08-46-001A

Date: March 07, 2005

INFORMATION

Subject:
Required Reconfiguration of OnStar(R) Modules After Replacement

Models:
All 2000-01 Passenger Cars and Trucks
with OnStar(R)

Supercede:

This bulletin is being issued to cancel Corporate Bulletin Number 01-08-46-001. Please discard all copies of Corporate Bulletin Number
01-08-46-001 (Section 08 - Body and Accessories).

This bulletin effectively cancels Corporate Bulletin Number 01-08-46-001. The information contained in this bulletin is now available in SI. Please
refer to OnStar Reconfiguration in the Cellular Communications sub-section of Body and Accessories for the applicable vehicle(s).

DisclaimerTechnical Service Bulletin # 99-08-46-001A Date: 050308


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 353
Chevrolet Venture V6-3.4L VIN E 2678

OnStar(R) - Dealer Kits No Longer Available


Bulletin No.: 99-08-46-001A

Date: March 08, 2005

INFORMATION

Subject:
OnStar(R) Kit Part Numbers and Compatibility

Models:
1996-2000 Passenger Cars and Trucks

with OnStar(R) System

Supercede:

This bulletin is being issued to cancel Corporate Bulletin Number 99-08-46-001. Please discard all copies of Corporate Bulletin Number
99-08-46-001 (Section 08 - Body and Accessories).

This bulletin effectively cancels Corporate Bulletin Number 99-08-46-001. The dealer kits mentioned in that bulletin are no longer available.

DisclaimerTechnical Service Bulletin # 01045B Date: 060421

Campaign - Closure Announcement


Subject:
Customer Satisfaction - OnStar Global Positioning System (GPS)
# 01045B - (04/21/2006)

Models:
2000 GMC Yukon, Yukon XL, Denali, Envoy, Jimmy
2000 Cadillac Escalade, DeVille, Seville, Eldorado, Catera
2000 Buick Park Avenue, LeSabre, Century, Regal
2000 Oldsmobile Bravada, Silhouette, Intrigue
2000 Pontiac Bonneville, Montana, Grand Prix
2000 Chevrolet Blazer, Suburban, Tahoe, Venture, Impala, Lumina, Monte Carlo
2001 Pontiac Aztek

This bulletin is being revised to announce the closure of this recall. Please discard all copies of recall bulletin 01045A, issued July, 2002.

Please be advised that this recall has been officially closed. Owners of vehicles that were involved in this recall, but who did not respond to the
customer letters, have already been refunded their remaining subscription fees following the de-activation of their systems.

DisclaimerTechnical Service Bulletin # 99-09-41-004 Date: 000101

Air Bag (SIR) On-Off Switch Kits, New Parts and Service
Bulletin Number:
99-09-41-004

Section:
09 - Restraints

Date:
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 354
Chevrolet Venture V6-3.4L VIN E 2679
January, 2000

Title:
Frontal Supplemental Inflatable Restraints (SIR) On-Off Switch Kits, New Parts and Procedures

Models:
1988-2000 Passenger Cars and Trucks

This bulletin is being revised to add the 1999 & 2000 model years. Please discard Corporate Bulletin Number 73-90-23 (Section 9 - Accessories).

Never consider installing an air bag on-off switch unless the following conditions are met:

1. The customer presents a letter from NHTSA authorizing the installation of the air bag on-off switch.

2. The dealership gives the customer a copy of the NOTICE TO GM OWNERS ABOUT AIR BAG ON-OFF SWITCHES.

3. The customer still wants the air bag on-off switch installed.

This bulletin includes information regarding switches to turn off and on frontal air bags, additional switch/display light diagnosis, switch
installation kit content descriptions and ordering directions for special pants (if required).

Some time ago, the National Highway Traffic and Safety Administration (NHTSA) announced a new regulation about air bags. The new regulation
includes procedures that will permit the installation of air bag on-off switches for the few customers who, in NHTSA's opinion, fit the criteria for
switches.

Important:
Due to the new regulation, DEALERS SHOULD NO LONGER USE THE INFORMATION ON AIR BAG DISCONNECTION (Corporate
Bulletin # 73-90-12, dated June, 1997). INSTEAD, USE THE INFORMATION INCLUDED WITH THIS BULLETIN.

The switch installation kit contains the necessary components (switch, bracket, attaching hardware, display light, applique, sheet for switch and
light, tie straps and instruction sheets) for system operation.

Some kits also include a replacement safety belt for certain vehicles that are designed with specific FORCE LIMITING safety belt systems. Special
Owner's Manual inserts are included in the installation kit for system operation review by the owner.

Additional equipment such as a 12 volt test lamp and the J 38125-B (-A or -500 will also apply) Terminal Repair Kit, are required to complete the
switch kit installation. In some cases, scan tools (Tech II or equivalent) may be required to reprogram certain control modules.
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 355
Chevrolet Venture V6-3.4L VIN E 2680

The cost of the switch kit and labor to install the switch kit are the responsibility of the customer. Suggested times for installation are in the
illustration.

Important:
In rare instances, the installation of switch(es) may turn on the vehicle air bag warning light. This condition may exist due to the additional
resistance of the switch and harness when added to the SIR system. In these rare instances, a SPECIAL SERVICE ONLY Diagnostic Energy
Reserve Module (DERM) of Sensing and Diagnostic Module (SDM) will be made available to the owner from GMSPO at no charge for the
parts and labor. Prior to ordering and/or installing a switch kit, the customer should be advised that this potential does exist and can be resolved
by one of the following options:

If the light does come on after switch installation (AND PROPER INSTALLATION AND CONNECTIONS HAVE BEEN VERIFIED), advise the
customer that the light has come on and that the vehicle:

^ May be driven with the light on until the special DERM or SDM is available. The switch portion to turn off the air bag will still function
properly, but the warning light will be on until the additional part can be obtained. When the DERM or 5
SDM is available, the customer should return to have the part installed (at no cost to the customer) OR

^ May have the existing air bag system reconnected and leave the switch (inoperative) in the vehicle until the additional part can be obtained.
When the DERM or SDM is available, the customer should return to have the part installed (at no cost to the customer).

The standard SIR system diagnosis can be made by disconnecting the switch from the SIR wiring harness and following the directions for SIR
System Diagnosis found in the appropriate Service Manual.

A description of the major components of the installation kit is as follows:

SWITCHES

One switch kit will be required for each air bag (driver or passenger) and will be ignition key operated. When the switch is in the OFF position, the
air bag will remain OFF until the switch is turned to the ON position. Turning the switch to the ON position will allow the air bag to function.
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 356
Chevrolet Venture V6-3.4L VIN E 2681

The recommended locations for the switches on most vehicles is in the instrument panel glove compartment (center console if vehicle has no glove
compartment) or, in the case of some vans, in the center stowage compartment (see the recommended location illustrations that are provided with
each switch kit).

Important:
Switches or display light indicators MUST NOT be placed on any instrument panel surfaces directly in front of the driver's or passenger's leg or
knee areas.

DISPLAY LIGHT

Each switch requires a display light to indicate the OFF status of the air bag. Each display light includes a harness to be connected to the switch
harness. The recommended mounting locations for the display lights vary, but are typically located at the center front edge of the roof headliner (or
windshield garnish molding) above the rear view mirror (see the recommended location illustrations provided with each switch kit).

Important:
When installed, driver and/or passenger display light(s) must be visible by all front seat occupants.

Important:
Switches or display light indicators MUST NOT be placed on any instrument panel surfaces directly in front of the driver's or passenger's leg or
knee areas.

WIRING CONNECTIONS

In general terms, the switch will be connected IN SERIES with the appropriate air bag (at the service disconnect) and will require additional
connection of a feed wire to an ignition fed circuit and a ground wire to the body to complete the circuit for the display light indicator.
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 357
Chevrolet Venture V6-3.4L VIN E 2682
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 358
Chevrolet Venture V6-3.4L VIN E 2683

Diagnostics for the switch and display light are included in the illustrations. As always, the technician should make sure to review the wiring
harness routing and installation for pinching, rubbing and chafing to brackets, braces (etc.) and take appropriate actions to protect the wiring from
those potential conditions.

PARTS INFORMATION

Order the appropriate Installation Kit(s) (passenger, driver, or both) from GMSPO. For kit part numbers and usage, see Group 14.865 of the
appropriate GMSPO Parts Catalog.

If special DERMs or SDMs are required to resolve a WARNING LIGHT ON condition, order the part from GMSPO in the normal manner. For
part numbers and usage see Group 14.865 of the appropriate GMSPO Parts Catalog.

Important:
1995-98 G (Aurora and Riviera) and 1997-00 Y (Corvette) switch kits include replacement safety belts. These belts MUST replace the original
safety belts when installing a switch kit. Aurora and Riviera models built on or after January 1,1998 will include DEPOWERED air bags, and
the safety belts on these vehicles will not be included in switch kits and MUST NOT BE CHANGED. The 1997-00 Corvette models will
require safety belt changes regardless of build dates. The belts will be replaced at no charge for the parts or the labor.

WARRANTY INFORMATION

Switch kits and installation are NOT considered a warranty repair. Pans and labor charges (except for special DERM or SDM and replacement
safety belt installation if required) are the responsibility of the customer. If special DERMs or SDMs are required to resolve a WARNING LIGHT
ON condition, USE THE EXISTING LABOR OPERATION AND TIME ALLOWANCES WITH THE SPECIAL CUSTOMER AND FAILURE
CODES WHEN SUBMITTING CLAIMS:

DERMs

USE LABOR OPERATION C8815, CUSTOMER COMPLAINT CODE WK AND FAILURE CODE 93. USE PUBLISHED LABOR
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 359
Chevrolet Venture V6-3.4L VIN E 2684
OPERATION TIMES.

SDMs

USE LABOR OPERATION C8817, CUSTOMER COMPLAINT CODE WK AND FAILURE CODE 93. USE PUBLISHED LABOR
OPERATION TIMES. When installing switch kits on 1995-98 Aurora, Riviera and 1997-00 Corvette models, the appropriate safety belts must be
replaced. When submitting claims, use the existing labor operation and time allowances with special customer complaint and failure codes. The
LABOR ONLY may be claimed. The cost of the belt is included in the kit price.

USE C9040 RIGHT SIDE ONLY, C9041 LEFT SIDE ONLY OR C9047 FOR BOTH AND INCLUDE THE CUSTOMER COMPLAINT CODE
MH AND FAILURE CODE 93 USE PUBLISHED LABOR OPERATION TIMES.

ADMINISTRATIVE INFORMATION

When the dealer decides to install an air bag on-off switch under NHTSA's new regulation, the dealer should fill out and send to NHTSA the form
entitled INSTALLATION OF AIR BAG ON-OFF SWITCHES. The dealer should also keep:

1. A copy of the INSTALLATION form.

2. A copy of the letter NHTSA sent to the customer authorizing the switch.

3. A copy of any waiver the dealer obtains from the customer when the switch is installed.

Important:
In addition, the new regulations require dealers to send the original of the customer's signed authorization form to NHTSA at the following
address:

National Highway Traffic Safety Association


Attention: Air Bag Switch Forms
400 Seventh Street, S.W.
Washington, D.C. 20590-1000
Technical Service Bulletin # 03-09-41-003A Date: 050209

Restraints - Air Bag System Diagnostics


Info - Proper Air Bag System Diagnosis and Service # 03-09-41-003A - (Feb 9, 2005)

Models:
2004 and Prior Passenger Cars and Light Duty Trucks

Excluding 2004 Pontiac Grand Prix

This bulletin is being revised to remove 2004 Pontiac Grand Prix for the models. Please discard Corporate Bulletin Number 03-09-41-003 (Section
9 - Restraints).

This bulletin is being issued to emphasize several aspects of proper diagnosis and servicing of the Air Bag System.

Air Bag Readiness Light

As stated in Owners Manuals, if the air bag readiness light stays on after the vehicle is started, the system may not be working properly. The air
bags may not inflate in a crash or may even inflate without a crash. If the Air Bag Readiness Light/Indicator is illuminated or comes on
intermittently, diagnose to determine the cause. Refer to Air Bag Indicator Circuit Malfunction in the SIR sub-section of the appropriate Service
Manual.

Replacement of Soaked SDMs

As stated in Service Manuals, if the vehicle interior is exposed to moisture and becomes soaked up to the level of the sensing and diagnostic module
(SDM), the SDM and SDM harness connector must be replaced. The SDM could be activated when powered, which could cause air bag
deployment and result in personal injury. The air bags, as well as the sensors and related parts, would have to be replaced. To help avoid this
situation, turn the ignition off immediately. DO NOT turn the ignition back on, even to tow the vehicle, unless the battery cable is first
disconnected.

Replacement of SDM that Shows Signs of Water Exposure or Corrosion

If an SDM that is being replaced shows signs of water exposure or corrosion and the customer does not know the source of the water exposure, then
the vehicle should be checked for water leaks. If leaks are found, the customer should be advised to have them repaired to help avoid damage to the
replacement SDM.
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 360
Chevrolet Venture V6-3.4L VIN E 2685

DisclaimerTechnical Service Bulletin # 02-08-56-001 Date: 020201

PASS-KEY III - Revised Relearn Procedure


File In Section: 08 Body and Accessories

Bulletin No.: 02-08-56-001

Date: February, 2002

SERVICE MANUAL UPDATE

Subject:
Revised PASS-KEYIII(R) Relearn Procedure

Models:
1997-2000 Buick Park Avenue
2000 Buick LeSabre
1998-2000 Cadillac Seville
2000 Cadillac DeVille
1999-2000 Chevrolet Venture
1999-2000 Oldsmobile Silhouette
1999-2000 Pontiac Trans Sport/Montana
2000 Pontiac Bonneville, Grand Prix

This bulletin is being issued to revise the PASS-KEYIII(R) Relearn procedure in the Theft Deterrent sub-section of the affected Service Manuals.
Please replace the current information in the Service Manual with the following information.

The following information has been updated within SI2000 for 1998-2000. If you are using a paper version of these Service Manuals, please make
a reference to this bulletin on the affected page.

The above mentioned Service Manuals stated either in the title and/or in the text of the Relearn or Autolearn procedure that when replacing an
ignition lock cylinder assembly, it is necessary to do the relearn procedure. When replacing an ignition lock cylinder on these vehicles, a relearn
procedure is not required.

A programming procedure is still required when replacing a Theft Deterrent Control Module or a steering column assembly that comes with a new
Theft Deterrent Control Module and the ignition keys.

Important:
A new GMSPO service replacement PCM will learn the theft password when the ignition is cycled on for the first time.

DISCLAIMERTechnical Service Bulletin # 02-06-05-004B Date: 060214

Accessories - DTC's P0300, P1380, P1381


Bulletin No.: 02-06-05-004b

Date: February 14, 2006

INFORMATION

Subject:
Misfire DTCs P0300, P1380, P1381 and Catalytic Converter Damage Due to Installation of Alarm Systems

Models:
2006 and Prior GM Passenger Cars and Light Duty Trucks
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 361
Chevrolet Venture V6-3.4L VIN E 2686
2006 and Prior HUMMER H2, H3
2006 and Prior Isuzu Light Duty Trucks

Supercede:

This bulletin is being revised to add model years. Please discard Corporate Bulletin Number 02-06-05-004A (Section 06 - Engine/Propulsion
System). General Motors Engineering, in an effort to determine the root cause of catalytic converter damage, has determined that aftermarket alarm
systems incorrectly installed in vehicles have the potential to cause misfire codes and damage to the converter. These alarm systems use a circuit
interrupt which utilizes the ignition circuit on the vehicles.

These alarm systems utilize mechanical relays and normal vehicle movement can trigger these relays to engage and disengage the ignition circuit
while the vehicle is in motion. These disruptions of the ignition circuit, which occur in milliseconds, may cause more fuel to be commanded.
Overtime, this dumping of fuel on and off again can cause misfire codes and ultimately damage the converter assembly.

Important:
Engineering could not identify any alarms that utilize solid state circuitry that would eliminate this concern. Because of this, it has been
determined that all alarm systems must be routed through the starter circuit in order to avoid this condition.

Dealers must be aware of this issue and take note of the wiring on vehicles with alarm systems that come in for repair, particularly for catalytic
converter damage that seem to have no known root cause.

DisclaimerTechnical Service Bulletin # 05-06-04-028 Date: 050418

Engine Controls - OBD System Monitor Operation


Bulletin No.: 05-06-04-028

Date: April 18, 2005

INFORMATION

Subject:
OBD I/M System Monitors Not Supported

Models:
1999-2000 Buick Century, LeSabre, Park Avenue, Regal, Riveria
1999-2000 Chevrolet Camaro, Lumina, Malibu, Monte Carlo, Venture
2000 Chevrolet Impala
1999 Oldsmobile Cutlass, Eighty Eight
1999-2000 Oldsmobile Alero, Intrigue, Silhouette
1999-2000 Pontiac Bonneville, Firebird, Grand Am, Grand Prix, Montana, Trans Sport

with 3.1L, 3.4L, 3.5L or 3.8L V-6 Engine (VINs J, E, H, K, 1 - RPOs LG8, LA1, LX5, L36, L67)

A scan tool system status display will indicate whether the major OBD monitors are Complete, Not Complete or Not Supported.

OBD system monitors are grouped as those that run continuously during a trip or those that do not run continuously during a trip (non-continuous).
Continuously running OBD system monitor status should always indicate that the monitor is complete.

Several U.S. states require that the above vehicle's major On-Board Diagnostic (OBD) monitors have completed prior to an OBD I/M emission
inspection. Some areas may reject a vehicle from testing if certain non-continuous OBD monitors are not complete.

When scanning the system status on the vehicles identified above, it may have been noted that the scan tools or emission test equipment will
incorrectly indicate the OBD system status as Not Supported for the continuously running monitors (Misfire, Fuel System, and Comprehensive
Components). There is not a fault with the diagnostic system or the vehicle and repairs should not be attempted.

Further, continuous monitor system status for gasoline engines is not considered when preparing for an OBD I/M emission inspection. A vehicle
with the MIL commanded on for a continuous system monitor, or for any reason, should be serviced.
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 362
Chevrolet Venture V6-3.4L VIN E 2687

DisclaimerTechnical Service Bulletin # 00-06-04-021 Date: 000501

EVAP System - Service of Connectors


File In Section: 06 - Engine/Propulsion System

Bulletin No.: 00-06-04-021

Date: May, 2000

INFORMATION

Subject:
Proper Service of Quick Connect EVAP System Connectors

Models:
1985-2001 Passenger Cars and Trucks

The EVAP system must be serviced properly. Improper service of the EVAP system can cause EVAP system leaks and set an engine DTC.

Important:
DO NOT cut or kink EVAP hoses/pipes to service the EVAP system. A damaged, cut or kinked EVAP system hose/pipe must be replaced and
NOT REPAIRED.

To properly service the EVAP system, it is important to correctly identify the style of quick connect EVAP fitting used in the EVAP system.
Correctly identifying the style of fitting will aid in the proper disconnection/connection of the fitting and the ability to reuse the fitting.

Improper disconnection and/or connection of EVAP fittings can cause the following conditions and set engine DTCs:

^ Leaks in the EVAP system

^ Damage to the EVAP fitting(s)

^ Damage to and/or adversely effect the function of the EVAP components such as:

- Purge solenoid

- Canister

- Vapor lines

1. To properly disconnect this style of fitting, slide the tab in and pull the fittings apart.
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 363
Chevrolet Venture V6-3.4L VIN E 2688

2. To reconnect this style of fitting, install the fittings back together and gently pull back on the fittings to verify proper connection of the
fittings.

1. To properly disconnect this style of fitting, push in both sides of the retaining feature and pull the fittings apart.

2. To reconnect this style of fitting, install the fittings back together and gently pull back on the fittings to verify proper connection of the
fittings.

To properly disconnect this style of fitting, use the following procedure:


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 364
Chevrolet Venture V6-3.4L VIN E 2689

1. Move the tab of the retainer away from the male fitting in order to clear the retaining nub.

2. Move the tab of the retainer in the direction shown and pull the fittings apart.

3. To reconnect this style of fitting, install the fittings back together and gently pull back on the fittings to verify proper connection of the
fittings.

To properly service this style of fitting use the following procedure:


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 365
Chevrolet Venture V6-3.4L VIN E 2690

1. Push in both tabs of the retainer.

2. Pull the female fitting away from the male fitting.

3. Remove and discard the retainer fitting from the male fitting.
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 366
Chevrolet Venture V6-3.4L VIN E 2691

4. Remove and discard the indicator ring (factory use only) from the male fitting.

5. Install a NEW retainer fitting into the female fitting.

6. Connect the fittings together until a snap is heard and/or felt signifying the retainer tabs have engaged the raised feature of the male fitting.
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 367
Chevrolet Venture V6-3.4L VIN E 2692

7. Gently pull back on the fittings to verify proper connection of the fittings.

DisclaimerTechnical Service Bulletin # 00-06-04-011A Date: 011001

EVAP System - Monitor Strategy


File In Section: 06 - Engine/Propulsion System

Bulletin No.: 00-06-04-011A

Date: October, 2001

INFORMATION

Subject:
Evaporative Emissions DTC P0440, P0441, P0442, P0446

Models:
1996-2002 Passenger Cars and Trucks
With Enhanced Evaporative Emissions Engines
Except 1998-1999 Chevrolet Prizm

This bulletin is being revised to add model years and diagnostic enhancements.

Please discard Corporate Bulletin Number 00-06-04-011 (Section 6-Engine).

Enhanced Evaporative Emissions testing of 1996 and newer vehicles with enhanced evaporative emissions requires more stringent testing of the
fuel system for evaporative emissions leaks. Vehicles with this system use an on-board diagnostic module (i.e. Powertrain Control Module (PCM)
or Vehicle Control Module (VCM) as the controller. For the balance of this bulletin, we will refer to either of these components as a module.

Enhanced Evaporative Emission tests may be performed by the vehicle's module when specific conditions are met. These conditions are determined
by the calibration within the module. These calibrations are vehicle platform and engine family specific. When the key is turned to the start or run
position, the module checks the output of various sensors on the vehicle to determine when and if the Evaporative Emissions tests should be run.
Refer to Engine Controls sub-section of the appropriate Service Manual for specific DTC information.

Some of the most widely used parameters are listed below:

1. The Barometric Pressure (BARO) is greater than a specified kPa (psi).

2. The system voltage is between 10 and 18 volts.

3. The intake air temperature (IAT) is within specified temperature values.

4. The engine coolant temperature (ECT) is within specified temperature values.

5. The ECT and IAT are within specified temperatures of each other when the vehicle engine was started.
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 368
Chevrolet Venture V6-3.4L VIN E 2693

6. The fuel level sensor indicates the fuel level is greater than a specified % of empty and less than a specified % of full. (For a 76 L (20 gal)
fuel tank, a fuel level of more than 11 L (3 gal) but less than 64 L (17 gal) or as specified in the calibration).

7. Some platforms such as the Alero and Grand Am, use a miles driven check as well.

For the ECT and IAT to be within the specified temperatures of each other at the time of engine start-up, the engine will have to be in the
non-running condition for a long enough period of time for the engine coolant temperature to drop from its normal operating temperature down to
roughly 30°C (90°F). This could take several hours.

When the control module determines that the above conditions are met, the module tests for a leak in the EVAP system by:

^ Electrically closing the vent valve in order to seal the system.

^ Electrically opening the purge valve which allows the running engine to draw a vacuum on the fuel tank.

^ The module then closes the purge valve, resealing the system.

^ The module then monitors the fuel tank pressure sensor and determines:

- If vacuum was achieved.

- If a leak is present, how large the leak is.

- If vacuum was not achieved.

^ If one of the above tests fails, the module remembers that the system failed the test.

^ If the module sees a failure of the EVAP test for two consecutive tests, the module will set a trouble code for EVAP leak (DTCs P0440, P0442,
or P0446).

Important:
If the PCM is completing the EVAP diagnostic, filling of the fuel tank cannot be completed as the vent valve will be closed and the fuel
dispenser nozzle will sense the pressure build-up and shut down. This is the expected result. No parts should be replaced as nothing is faulty To
keep from encountering this situation, it is imperative all customers and dealership personnel be advised NOT TO FILL THE FUEL TANK
WITH THE ENGINE RUNNING. If the condition is encountered, turn the ignition to the OFF position for a minute. This will allow the PGM
to go to sleep completely, thereby opening the vent valve.

DisclaimerTechnical Service Bulletin # 01-06-04-044 Date: 011101

EVAP System - Special Tool Usage


File In Section: 06 - Engine/Propulsion System

Bulletin No.: 01-06-04-044

Date: November, 2001

INFORMATION

Subject:
Test Guidelines for Use of Essential Tool J 41413-200 Evaporative System Tester

Models:
2002 and Prior Passenger Cars and Light Duty Trucks with Non-Enhanced and Enhanced EVAP Systems

The J 4141-200 Evaporative Emission System Tester (EEST) updates the J 41413 Evaporative Pressure/Purge Diagnostic Station. Continue to use
the appropriate Service Information substituting the J 41413-200 Evaporative Emission System Tester (EEST) and this bulletin procedure in any
diagnostic step requiring the use of the J 41413. This includes the Inspection Maintenance (I/M) Emissions Diagnostic Manual Pre-OBD II
GMPT/97-IM240.

Some 1996 to 1998 and all 1999 and newer GM cars and light trucks are required to illuminate the malfunction indicator lamp (MIL) when the
On-Board Diagnostic (OBD II) system detects an evaporative emissions (EVAP) system leak equivalent to an orifice of 1 mm (0.040 in) diameter
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 369
Chevrolet Venture V6-3.4L VIN E 2694
or greater. In model year 2000, GM introduced software on some vehicles which requires illumination of the MIL when the OBD II system detects
an EVAP system leak equivalent to an orifice of 0.5 mm (0.020 in) diameter or greater. The new J 41413-200 EEST can be used on all GM cars
and light duty trucks.

GM cars and light duty trucks that meet this new standard cannot be diagnosed using the existing ultrasonic leak detection equipment. The new J
41413-200 EEST can be used to identify leaks and to verify repairs.

The J 41413-200 EEST introduces chemically inert smoke into the sealed EVAP system under low pressure. System leaks are located by using the J
41413-SPT high intensity white light to inspect for traces of smoke escaping from the sealed EVAP system.

DISCLAIMER

Non-Enhanced EVAP System Diagnostic Procedure


1. Pinch off or plug the EVAP vapor line to seal the EVAP system.

2. Connect the EEST red battery clip to the positive (+) battery terminal. Connect the black battery clip to chassis ground.

3. Install the appropriate fuel fill cap adapter to the fuel fill pipe. Refer to the Service Information for the appropriate fuel fill cap adapter part
number.

4. Connect the EEST's nitrogen/smoke supply hose and vehicle fuel fill cap to the adapter.

5. Turn the nitrogen/smoke valve on the EEST control panel to SMOKE.

6. Use the remote switch to introduce smoke into the EVAP system for 60 seconds.

Important:
Additional smoke may need to be introduced at 15-second intervals until the leak source has been located.

7. Inspect the entire EVAP system for exiting smoke using the high intensity white light (J 41413-SPT).
Enhanced EVAP System Leak Detection Procedure
When diagnosing DTCs P0440, P0442, P0446 and P0455, use the J 41413-200 EEST along with the following procedure anytime the diagnostic
calls for the J 41413 EVAP Pressure/Purge Diagnostic Station.

Important:
ENSURE THAT THE VEHICLE UNDERBODY TEMPERATURE IS SIMILAR TO THE AMBIENT TEMPERATURE AND ALLOW THE
SURROUNDING AIR TO STABILIZE BEFORE STARTING THE DIAGNOSTIC PROCEDURE.

1. Turn ON the ignition with the engine OFF.

2. Command the EVAP vent valve closed with a scan tool.*

*Prizm: In order to seal the EVAP system on the 1998-2002 Prizm, bypass the EVAP canister by connecting the fuel tank vapor hose to the
canister purge line. Refer to the Service Information for additional information.

3. Connect the EEST red battery clip to the positive (+) battery terminal. Connect the black battery clip to chassis ground.

4. Install the appropriate fuel fill cap adapter to the fuel fill pipe. Refer to the Service Information for the appropriate fuel fill cap adapter part
number.

5. Connect the EESTs nitrogen/smoke supply hose and vehicle fuel fill cap to the adapter.

6. Turn the nitrogen/smoke valve on the EEST control panel to SMOKE.

7. Use the remote switch to introduce smoke into the EVAP system.

8. Use the J 41413-VLV EVAP Port Vent Fitting tool to open the EVAP service port (if equipped) until smoke is observed.

9. Remove the J 41413-VLV EVAP Port Vent Fitting tool once smoke is observed.

Important:
Additional smoke may need to be introduced at 15-second intervals until the leak source has been located.
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 370
Chevrolet Venture V6-3.4L VIN E 2695

10. Continue to introduce smoke into the EVAP system for an additional 60 seconds.

11. Inspect the entire EVAP system for exiting smoke with the J 41413-SPT high intensity white light. If leak source was located, repair as
necessary and proceed to verification process.

12. If the leak source was not located, stop introducing smoke into the EVAP system.

13. Disconnect the fuel fill cap adapter from the fuel fill pipe. Install the fuel fill cap to the vehicle.

14. Connect the EEST's nitrogen/smoke supply hose to the EVAP service port (if equipped).

15. Use the remote switch to introduce smoke into the EVAP system.

16. Inspect the entire EVAP system for exiting smoke with the J 41413-SPT high intensity white light. If leak source was located, repair as
necessary and proceed to verification process.

17. If no leak was located, proceed to Fuel Tank Pressure (FTP) Sensor check.
Fuel Tank Pressure (FTP) Sensor Check
The J 41413-200 EEST provides a tight seal to the nitrogen/smoke hose when the tester is turned off. This allows pressurizing of the sealed EVAP
system. Use the following procedure to test for a functional FTP sensor.

1. Turn ON the ignition with the engine OFF.

2. Connect the EEST red battery clip to the positive (+) battery terminal. Connect the black battery clip to chassis ground.

3. Install the appropriate fuel fill cap adapter to the fuel fill pipe. Refer to the Service Information for the appropriate fuel fill cap adapter part
number.

4. Connect the EEST's nitrogen/smoke supply hose and vehicle fuel fill cap to the adapter.

5. Compare the FTP parameter, with a scan tool, to the EEST pressure/vacuum gage.

6. If the FTP parameter is not within 1 in H20 of the EEST pressure/vacuum gage, replace the FTP sensor.

7. Command the vent valve closed with a scan tool.

8. Turn the nitrogen/smoke valve on the EEST control panel to Nitrogen.

9. Use the remote switch to introduce nitrogen into the EVAP system.

10. Observe the Fuel Tank Pressure (FTP) parameter with a scan tool. The FTP sensor parameter should increase to more than 5 in H20.

11. If the FTP parameter is not more that 5 in H20, replace the FTP sensor.

12. If the FTP parameter is more than 5 in H20, continue with appropriate Service Information.
Verification Procedure
Service Bay Test

Important:
Disconnect the fuel fill cap adapter and install the fuel fill cap onto the.vehicle prior to performing the EVAP Service Bay Test.

Perform the EVAP Service Bay Test (if available) using a scan tool. If the Service Bay Test is not available, proceed to Flow Meter Test.

The Service Bay Test will verify the proper operation of the EVAP system and reset the Emissions Inspection/Maintenance EVAP flag.

Results

^ If the Service Bay Test is passed, testing is complete.

^ If the Service Bay Test is not passed, return to the appropriate Service Information.

Flow Meter Test

The flow meter test must be used to verify repairs on vehicles with enhanced EVAP systems that do not have the EVAP Service Bay Test.

1. Turn the nitrogen/smoke valve to nitrogen.

2. Disconnect the nitrogen/smoke hose from the fuel fill cap adapter.
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 371
Chevrolet Venture V6-3.4L VIN E 2696

3. Connect the nitrogen/smoke hose to the correct test orifice on the bottom-front of the EEST. The correct test orifice can be determined by
referencing the table.

4. Use the remote switch to activate the EEST.

5. Align the red flag on the flow meter with the floating indicator. Use the remote switch to de-activate the EEST.

6. Remove the nitrogen/smoke hose from the test orifice and reinstall the hose onto the fuel fill cap adapter.

7. Turn ON the ignition with the engine OFF.

8. Command the EVAP vent valve closed with a scan tool.

Important:
Larger volume fuel tanks and/or those with lower fuel levels may require several minutes for the floating indicator to stabilize.

9. Use the remote switch to introduce nitrogen and fill the EVAP system. Watch the floating indicator until it stabilizes.

10. Compare the flow meter's stable floating indicator position to the red flag. If the indicator floats:

^ ABOVE the red flag-UNACCEPTABLE (EVAP system leak still exists-go to Enhanced EVAP System Leak Detection Procedure earlier
in this bulletin).

^ BELOW the red flag-ACCEPTABLE (PASS-test complete).


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 372
Chevrolet Venture V6-3.4L VIN E 2697

The chart shown should be used to select the correct orifice for the Verification Process if the Service information does not specifically list the
information.Technical Service Bulletin # 00-06-04-026 Date: 000601

PCM - Returned Product Feedback Program


File in section:
06- Engine/Propulsion system

Bulletin No:
00-06-04-026

Date:
June, 2000

WARRANTY ADMINISTRATION

Subject:
powertrain Control Module (PCM) product Feedback Program
(Parts Return and Required Repair Order Documentation)

Models:
2001 and prior Passenger Cars and Trucks

Attention:
Dealerships Service and Parts Managers
A significant number of PCMs that are returned to GM test out with No Trouble Found (NTF). This can be caused by a number of factors.
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 373
Chevrolet Venture V6-3.4L VIN E 2698
Unfortunately the information received with the returned unit frequently lacks the necessary detail to preform an analysis targeted to the actual
failure condition. For this reason, a more extensive return process is being established using the Warranty Parts Center (WPC). Effective
immediately starting with 1996 and new model year vehicles, any PCM replaced under warranty (using labor operations J6360 only), should be
held in dealers inventory until the claim has been paid. The Warranty Parts Center (WPC) / corporate Parts Return (CPR) program may require the
replaced PCM with a copy of the repair order ( or repair order only )to be returned by the dealer to the WCP.The WCP will notify the dealer of the
PCM and R.O. return request by sending a "GM part and Repair Order Return Request " message Via the Dealer Communication System (DCS)
within the "Parts Return CPR"report application on Tuesday and Friday of each week as Warranty claims are paid. Refer to Corporate Bulletin
Number 99-00-89-019, dated October, 1999 (US dealers) or HOL # 1999-201 ( Canadian dealers).

Important
The most critical step within this program is that the dealer Must document the following information on the repair order anytime a PCM is
replaced. If the PCM and / or the R.O. is requested by the WPC to be returned and the required information has not been documented on the
R.O. correctly, the dealer may be debited for the total cost of the replaced PCM, any dealer cost mark up, any core cost, plus shipping and
handling costs.

GM appreciates your support in this product improvement initiative.


Required Repair Order Information

^ Detailed customer concern.


^ Was the malfunction Indicator Light/Service Engine Soon (MIL/SES) indicator on.
^ List all the PCM diagnostic trouble codes (DTCs) set (current or history).
^ If no DTCs are set, " No DTCs Set " should be indicated.
^ List the PCM Calibration Identification (CAL ID) number.

Also, in order to provide improved PCM Diagnostic Procedures, please list the GM Service Information Document ID Number (from SI2000) that
led to the PCM replacement.

Important:
The PCM diagnostic trouble codes (DTCs), Calibration Identification (Cal ID) Number, and the GM Service Information Document ID Number
(from SI2000) should be documented in the Failure Code (99999) comments section. Refer to the Policy and Procedures Manual (section IV
Warranty Claim Data - G Failure Code ( or OBDII code ).

DisclaimerTechnical Service Bulletin # 02-09-41-001 Date: 020601

Computers & Controls - DTC's Set When Replacing Modules


File In Section: 09 - Restraints

Bulletin No.: 02-09-41-001

Date: June, 2002

INFORMATION

Subject:
DTCs B1001, B1271 or B1780 Set When Replacing/Reprogramming Other Modules

Models:
1999-2003 Passenger Cars and Trucks
with Class 2 Serial Data Communication Between Modules

This bulletin is being revised to add model years and reflect changes in the Tech 2(R) procedure and filing classification. Please discard Corporate
Bulletin Number 99-06-03-010A (Section 06 - Engine).

Class 2 Serial Data Communication allows control modules (i.e. the Powertrain Control Module (PCM), the Body Control Module (BCM), the
Dash Integration Module (DIM), the Instrument Panel Cluster (IPC), the radio, the Heating, Ventilation and Air Conditioning (HVAC) Controller,
and the Sensing and Diagnostic Module (SDM) to exchange information. This information may be operational information or identification
information. Among the identification information exchanged and compared within these modules is the Vehicle Identification Number (VIN).
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 374
Chevrolet Venture V6-3.4L VIN E 2699
Typically the one module, the master module, broadcasts the VIN and all the other modules compare the VIN stored within itself. When the
broadcast VIN does not match the VIN stored within the SDM, the following actions occur:

^ DTC B1001 Option Configuration Error is set and deployment of the airbags is inhibited.

^ DTC B1271 or a DTC B1780 Theft Locked. The VIN information is also used by the radio. When the VIN does not match the VIN stored
within the radio, DTC B1271 or DTC B1780 is set and the radio is inoperative.

Additionally, the master module will compare the SDM's part number (last four digits) to determine if the correct SDM is installed in the vehicle. If
the SDM is the wrong part, a B1001 will also set.

This situation may occur when a vehicle is being repaired. When a PCM or a body control type module is replaced, the VIN information must be
programmed into the replaced (new) control module. A module which has had VIN information entered into it (for example, one taken from
another vehicle) cannot be reprogrammed. VIN information can only be entered into new modules. The ignition must be ON in order to program
the control module. Since the VIN information is broadcast when the ignition goes to ON from any other ignition switch position, DTCs may be set
in the SDM and/or the radio. Therefore, always follow the specified control module replacement procedures.

1. After completing the repair, turn OFF the ignition for at least 30 seconds.

2. Turn ON the ignition and check for DTCs using a Tech 2(R) scan tool.

If DTCs B1001, B1271, or B1780 are present with a history status, DO NOT REPLACE THE SDM OR THE RADIO.

3. Clear the DTCs from all modules using the Tech 2(R) scan tool.

4. Remove the Tech 2(R) from the vehicle

5. Ensure the proper operation of the SDM by turning OFF the ignition and then turning ON the ignition. The air bag warning indicator should
flash seven times and then go OFF.

Refer to Corporate Bulletin Number 99-09-41-001 for additional information regarding proper reprogramming of the new/replaced module.

Clearing codes from the other modules is part of the replacement and reprogramming procedure for the replaced module. The repair is not complete
unless all codes have been cleared from all modules.

DO NOT SUBMIT CLAIMS FOR OTHER MODULE REPLACEMENTS OR REPROGRAMMING.

DISCLAIMERTechnical Service Bulletin # 02-08-47-001 Date: 020701

Body Control - Update of Some Control Module DTC's


File In Section: 08 - Body and Accessories

Bulletin No.: 02-08-47-001

Date: July, 2002

SERVICE MANUAL UPDATE

Subject:
Revised DTCS B1000, B1004, B1007, B1009, B1013

Models:
2000-2002 GM Passenger Cars and Trucks

This bulletin is being issued to revise DTCs B1000, B1004, B1007, B1009 and B1013 in the Body Control Systems sub-section of the Service
Manual. Please replace the current information in the Service Manual with the following information.

The following information has been updated within SI2000. If you are using a paper version of this Service Manual, please make a reference to this
bulletin on the affected page.

Although the diagnosis for these DTCs is found in the Body Control Systems sub-section, multiple modules on the vehicle may set these DTCs.
Technicians have been replacing the Body Control Modules (BCM) even though the DTCs are retrieved as current from modules other than the
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 375
Chevrolet Venture V6-3.4L VIN E 2700
BCM. The tables for the above mentioned DTCs have been revised to clarify that the technician should replace the module setting the DTC as
current (the table information remains the same, only the wording has been revised for clarification purposes).

DISCLAIMERTechnical Service Bulletin # 02-07-30-022B Date: 031020

A/T - MIL/SES Lamp ON/Multiple A/T DTC's Set


Bulletin No.: 02-07-30-022B

Date: October 20, 2003

TECHNICAL

Subject:

Service Engine Soon (SES) Light On With DTCs P0716 and/or P0717, P0730, P0753, P0758, P1860, P1887, or other Miscellaneous Transmission
Trouble Codes Set (Repair Wiring at Transaxle Wiring Pass-thru Connector)

Models:
2000-2004 Buick Century, LeSabre, Park Avenue, Regal
2003-2004 Buick Rendezvous
2000-2001 Chevrolet Lumina
2000-2004 Chevrolet Cavalier, Impala, Malibu, Monte Carlo, Venture
2004 Chevrolet Classic
2000-2002 Oldsmobile Intrigue
2000-2003 Oldsmobile Aurora
2000-2004 Oldsmobile Alero, Silhouette
2000-2004 Pontiac Bonneville, Grand Am, Grand Prix, Montana, Sunfire
2001-2004 Pontiac Aztek
2000 Toyota Cavalier
with 4T65-E, 4T40-E or 4T45-E Transaxle (RPOs MN3, MN7, M15, M76, MN4, MN5)

Supercede:

This bulletin is being revised to add the 2004 model year as well as the Chevrolet Classic model. Please discard Corporate Bulletin Number
02-07-30-022A (Section 07-Transmission/Transaxle).

Condition

Some customers may comment that the Service Engine Soon (SES) indicator is illuminated and that while the light is illuminated, transmission
shifts are extremely harsh.

Cause

These types of conditions may be caused by an intermittent connection at the transaxle 20-way connector to the wiring harness interface.

Correction

If a DTC was recorded and the Freeze Frame and Failure Records back it up, a problem existed at one time with the wiring and/or the connectors
between the transaxle and the PCM. Therefore, a thorough inspection and/or repair of the wiring harness at the transaxle 20-way connector for one
or more of the following conditions may be warranted.

^ The wiring harness is stretched too tightly or other components are pressing on the connector body itself causing a downward pressure on the
connector body and possible intermittent contact of the wiring terminals. Ensure proper clearance to any other components and wiring (i.e.
hoses, battery cables, etc.).

^ The terminals are not fully seated into the cavity of the connector body.

^ The male terminals in the transaxle portion of the connector may be in the wrong position (i.e. bent).

^ The female terminals may be loose and are not making proper contact. Check the tension with the proper terminal tester from the GM Terminal
Test Kit J 35616-A or J 35616-92. If the tension is low, replace the terminal. Do not try to re-form the terminal.
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 376
Chevrolet Venture V6-3.4L VIN E 2701

^ The crimp of the terminal to the wire may not be satisfactory (i.e. loose, over insulation, etc.).

^ The wiring connector is not properly seated and locked in position. Ensure proper seating of the connector into the transaxle and that the
connector is properly locked in place.

Warranty Information

For vehicles repaired under warranty, use the table.

Disclaimer
Technical Service Bulletin # NHTSA01V067000 Date: 010301

Recall 01V067000: Sliding Doors May Not Latch


Vehicle Description: Minivans equipped with passenger side power sliding doors. The door closes but may not be latched. If this happens, the
power sliding door can open while the vehicle is in motion, particularly when the vehicle ascends a hill, makes a turn, or travels over a rough road
surface. An unrestrained occupant could fall out of the van and be injured. Dealers will install a new un-latch actuator assembly to the power
sliding door.Owner notification began April 18, 2001. Owners who take their vehicles to an authorized dealer on an agreed upon service date and
do not receive the free remedy within a reasonable time should contact Chevrolet at 1-800-222-1020, Pontiac at 1-800-762-2737, or Oldsmobile at
1-800-442-6537. Also contact the National Highway Traffic Safety Administration's Auto Safety Hotline at 1-888-DASH-2-DOT
(1-888-327-4236).
Technical Service Bulletin # 04-09-40-001 Date: 040105

Restraint System - 2nd Row Seat Belt Won't Release


Bulletin No.: 04-09-40-001

Date: January 05, 2004

INFORMATION

Subject:
Correct Location When Servicing Right Side 2nd Row Seat Belt Upper Anchor Bolt

Models:
1997-2004 Chevrolet Venture
1997-2004 Oldsmobile Silhouette
1997-2004 Pontiac Montana

The following information should be used when checking proper seat belt operation or when replacing the right side 2nd row seat belt assembly.
Some of the above listed vehicles may experience a condition where the 2nd row right side seat belt retractor will not release. When the seat belts
are fully extended, they go into a automatic locking mode, or cinch feature. This cinch feature enables the seat belts to stay tight and restrain child
seats developed before the advent of LATCH seats. The cinch feature is engaged by fully extending the seat belt from the retractor. Once engaged,
the seat belt can retract, but cannot be extended again until the clinch feature is cancelled. The cinch feature is cancelled when the seat belt has fully
retracted.

There are 4 different seating configurations for the second row and two different positions for the seat belt upper anchor bolt. Captain's chairs and
bucket seats use the lower anchor position, while split and full bench seats use the upper position. If a seat belt designed for the bucket or captains
chair is installed in the upper position, it cannot retract far enough to release the cinch feature. If you have a captains chair or bucket with a seat belt
retractor that will not release, check to make sure that the upper anchor bolt is in the lower position on the C-pillar. The bolts are reusable and
self-tapping.
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 377
Chevrolet Venture V6-3.4L VIN E 2702

DisclaimerTechnical Service Bulletin # 00-08-51-001 Date: 000901

Outside Rear View Mirror - Housing Turns Chalky/Dull


File In Section: 08 - Body and Accessories

Bulletin No.: 00-08-51-001

Date: September, 2000

Subject:
Outside Rear View Mirror Housing Turns Chalky/Dull
(Color/Clear Coat Mirror)

Models:
1998-2000 Buick Century, Park Avenue, Regal
1998-2000 Chevrolet Cavalier, Lumina, Malibu, Metro, Monte Carlo, Prizm,
Tracker, Venture
2000 Chevrolet Impala
1998-2000 Oldsmobile Intrigue, Silhouette
1999-2000 Oldsmobile Alero
1998-2000 Pontiac Bonneville, Grand Am, Sunfire, Trans Sport
1998-2000 Chevrolet and GMC C/K, S/T Models and M/L Van
1998-2000 Oldsmobile Bravada

Condition

Some customers may comment that the black plastic housing around the outside rear view mirror turns chalky or is dull in color.

Correction

Caution:
Sanding dust solvents and paint are potential health hazards. Make sure to wear an approved mask or fresh air supplied respirator that is
appropriate to the task being performed. Refinish both mirrors (Black WA 8555 with a gloss of 30%) following the GM Approved Refinish
Materials Booklet GM4901 M-D-2000 (GM4901 M-D-F-2000 (French)) under the flexible substrates section. Refer to your paint manufacturer
for specific process and application process for plastics.

Warranty Information

For vehicles repaired under warranty, use:

DISCLAIMERTechnical Service Bulletin # 03-08-42-007A Date: 040109

Lighting - Tail/Brake Lamp Bulb Inoperative


Bulletin No.: 03-08-42-007A
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 378
Chevrolet Venture V6-3.4L VIN E 2703

Date: January 09, 2004

TECHNICAL

Subject:
Tail Lamp/Brake Lamp Bulb Inoperative (Replace Bulb and/or Circuit Board)

Models:
2000-2004 Chevrolet Venture
2000-2004 Oldsmobile Silhouette
2000-2004 Pontiac Montana

Supercede:

This bulletin is being revised to add model years. Please discard Corporate Bulletin Number 03-08-42-007 (Section 08 - Body and Accessories).

Condition

Some customers may comment that the upper left hand or right hand tail lamp/brake lamp bulb is inoperative.

Cause

This condition may be the result of moisture entering the lamp housing and changing the bulbs resistance, causing the bulb to burn out and or
melting the circuit board.

Correction

Replace the burned out bulb and the circuit board if needed. Apply dielectric lubricant or dielectric grease to the left hand and right hand tail lamp
bulb terminals.

Refer to Tail Lamp Assembly and or Back up, Sidemarker, Stop, Turn Signal Bulb Replacement in SI.

Parts Information

Parts are currently available from GMSPO.

Warranty Information

For vehicles repaired under warranty, use the table.


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 379
Chevrolet Venture V6-3.4L VIN E 2704

Disclaimer
Technical Service Bulletin # 00-06-02-001 Date: 000101

Engine - Running Hot And/Or Loss of Coolant


Bulletin No.: 00-06-02-001

File In Section: 06 Engine/Propulsion System

Date: January, 2000

Subject:
Engine Running Hot, Overheating and/or Loss of Coolant (Polish Radiator Filler Neck and Replace Radiator Cap)

Models:
1999-2000 Passenger Cars and Trucks with Composite Radiator End Tank

Condition

Some customers may comment on one or more of the following conditions:

^ Engine running hot

^ Engine overheating, and/or

^ Loss of coolant/low coolant message

Cause

The radiator filler neck may have an imperfection in the sealing surface.

Correction

Important:
DO NOT REPLACE THE RADIATOR.

Using a piece of 400 grit wet/dry sandpaper backed with a flat piece of wood, polish the filler neck sealing surface using a circular motion.

Replace the radiator pressure cap with a cap of the same part number as shown in the GM Service Parts Catalog.

Warranty Information

For vehicles repaired under warranty, use:

Labor Labor
Operation Description Time

J3020 Cap, Radiator Filler - Replace 0.2 hr


Technical Service Bulletin # 00-06-02-004 Date: 000501

Radiator - Brown Substance On Cap & Upper Filler Neck


File In Section: 06 - Engine/Propulsion System

Bulletin No.: 00-06-02-004

Date: May, 2000

TECHNICAL

Subject:
Brown Colored Gel-Like Substance on Radiator Cap and Upper Filler Neck (Replace Radiator Cap and Clean Radiator Upper Filler Neck)
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 380
Chevrolet Venture V6-3.4L VIN E 2705

Models:
1997-2000 Buick Century
1996 Chevrolet Lumina APV
1996-2000 Chevrolet Lumina, Monte Carlo
1997-2000 Chevrolet Venture
2000 Chevrolet Impala
1996-1997 Oldsmobile Cutlass Supreme
1996-2000 Oldsmobile Silhouette
1996-1997 Pontiac Trans Sport
1996-2000 Pontiac Grand Prix
1998-2000 Pontiac Montana
with 3.1L or 3.4L Engine (VINs J, M, E, X - RPOs LG8, L82, LA1, LQ1)

Condition

Some customers may comment about a brown colored gel-like substance on the radiator cap and upper filler neck.

Correction

Important:
This condition is unique to the 3.1L and 3.4L engines and should not be confused with the condition described in Corporate Bulletin Number
99-06-02-012B - Rust in Coolant System.

This condition is almost always confined to the radiator cap and upper filler neck, so it is not necessary to change the coolant. keeping the cooling
system full at all times should eliminate future recurrence. Replace the radiator cap and clean the radiator upper filler neck using the procedure and
part numbers listed below.

1. Remove the radiator cap when the engine is cool.

^ Slowly rotate the cap counterclockwise to detent. Do not press down while rotating the pressure cap.

^ Wait until any residual pressure (indicated by a hissing sound) is relieved.

^ After all hissing stops, continue to rotate counterclockwise until the cap is removed.

2. Using a shop rag, clean the upper radiator filler neck of any residue.

3. Remove the coolant recovery reservoir if visually contaminated. Refer to the Coolant Recovery Reservoir Replacement procedure in the
Engine Cooling sub-section of the appropriate Service Manual.

4. If necessary, clean the coolant recovery reservoir and all hoses attached to it with soap and water. Rinse the reservoir and hoses with clean
water and drain.

Verify that the coolant can flow freely through the hoses.

5. Install the coolant recovery reservoir. Refer to the Coolant Recovery Reservoir Replacement procedure in the Engine Cooling sub-section of
the appropriate Service Manual.

6. Refill the coolant recovery reservoir with a 50/50 mixture of DEX-COOL(R) and clean drinkable or distilled water to the HOT mark. Fill to
the HOT mark to compensate for any air that may be in the cooling system.

7. Fill the radiator to the top of the filler neck.

8. Install the new radiator cap, P/N 10409635, making certain the arrows line up with the overflow tube.

9. Instruct the customer of the importance of maintaining the proper coolant level in the radiator and coolant recovery reservoir.

Parts Information

Part Number Description


10409635 Cap, Radiator Filler

Parts are currently available from GMSPO

Warranty Information
For vehicles repaired under warranty, use:

Labor Labor
Operation Description Time
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 381
Chevrolet Venture V6-3.4L VIN E 2706
J3020 Cap, Radiator Filler - Replace 0.2 hr
Add Cleaning Radiator Upper Filler Neck 0.1 hr
& Coolant Recovery Reservoir

DisclaimerTechnical Service Bulletin # 99-07-30-020A Date: 010401

A/T - Service Procedure Changes


File In Section: 07 - Transmission/Transaxle

Bulletin No.: 99-07-30-020A

Date: April, 2001

INFORMATION

Subject:
Automatic Transmission Service Procedure Changes

Models:
2002 and Prior Passenger Cars and Light Duty Trucks with Automatic Transmissions

This bulletin is being revised to add the 2000-2002 model years. Please discard Corporate Bulletin Number 99-07-30-020 (Section 07 -
Transmission).

This bulletin covers the service procedure for cars and light duty trucks equipped with automatic transmissions which are in warranty.

This service procedure allows dealers to repair or replace automatic transmissions based upon the cost of the repair and customer satisfaction. Each
repair should be evaluated individually to determine the need for repair or replacement.

^ Transmissions should be repaired whenever the cost of the repair is less than the cost of a Goodwrench Transmission Assembly.

^ A Goodwrench Transmission Assembly should be installed whenever the cost of the repair is greater than an assembly.

^ When two or more repair attempts have not corrected the condition, contact TAO and/or your Area Service Manger (ASM) (DSM in Canada)
for further assistance.

^ Only GM Goodwrench DEXRON(R)III automatic transmission fluid is to be used for any warranty service of automatic transmissions.

Cooler Flushing

Cooler flushing and a flow check MUST be performed whenever a transmission is removed for service. It is essential to flush the cooler prior to
installation of a Goodwrench Transmission Assembly or when fluid contamination is suspected. Use Kent-Moore tool J 35944-A and solvent J
35944-22 to flush the cooler. Instructions are published in each Service Manual On-Vehicle Service Section. Refer to Corporate Service Bulletin
99-07-30-017 for further details on transmission cooler flushing and flow check.

Warranty Information

Labor operation K7000 (TRANSAXLE ASSEMBLY - replacement) permits add on time to be used as needed for disassemble, inspect and
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 382
Chevrolet Venture V6-3.4L VIN E 2707
reassemble, when it has been determined the cost of overhaul exceeds cost of replacement. (Steps 3 and 5 ) as shown in the table.

Labor Operation K7000 (TRANSAXLE ASSEMBLY - replacement) includes time to perform cooler line flush. (Step 6 ) as shown in the table.

DISCLAIMER
Technical Service Bulletin # 01-07-30-029 Date: 011001

A/T - Core Return Product Feedback Form


File In Section: 07 - Transmission/Transaxle

Bulletin No.: 01-07-30-029

Date: October, 2001

INFORMATION

Subject:
New Product Feedback Form and Process For Automatic Transmission Core Returns

Models:
1980-2002 All Passenger Cars and Trucks
With All Original Equipment and Goodwrench Automatic Transmissions
(AC Delco Transmissions Are Not Included)

Quality improvement is a goal of General Motors, and as part of the ongoing quality improvement assessment efforts for automatic transmissions,
General Motors is implementing a new product feedback process. The new feedback process was developed after consulting with dealership
technicians and service managers, the General Motors Technical Assistance Center, and General Motors Regional Field Engineers.

The new process is being implemented in an effort to improve the quality and quantity of the feedback data. Accurate feedback from the technicians
will allow General Motors to accurately inspect and diagnose automatic transmission field returns. The new process utilizes four elements:

^ A new and easier-to-complete feedback form. The (US) 2001 Service Policies and Procedures Manual requires completion of this feedback
form in Article 1.6, page 10 and Article 1.7, page 2.

^ The new feedback form has English, French, and Spanish versions all printed on a single form. The service technician should complete the form
in the language of choice, fold/tear it in thirds, and INSERT IT IN THE SEE-THROUGH ENVELOPE, SO THAT THE COMPLETED
FEEDBACK INFORMATION CAN BE READ THROUGH THE RETURN ENVELOPE. The dealer copy of the feedback form is to be
maintained with the dealer's copy of the repair order. [Refer to the Service Policies and Procedures Manual. Article 1.6, page 10, (US)].

^ A new see-through return envelope to hold the feedback form when the transmission is returned to the warehouse.

The see-through return envelope will be attached to the side of the top half of the transmission shipping container at either of the small ends.

^ Auditing of/for completed feedback forms will be done during core receiving in Detroit, Michigan. GMSPO core return Code T98 will read
"TRANS FEEDBACK FORM NOT REC'D WITH CORE." The T98 zero dollar ($0) debit notice will be sent by GMSPO each time an OEM
or Goodwrench automatic transmission core is received without a completed product feedback form visible in the see-through envelope.

If the dealer should receive a Goodwrench automatic transmission without the see-through envelope attached, use one of the three new feedback
forms and envelopes being sent to each dealer with this bulletin.

If additional forms are needed contact:

In the U.S.A.

- GM Dealer World Delivery

- Phone at 1-866-700-0001, Fax 1-313-957-5555 or E-mail to DWD_orders@Buddco.com

- For the form P/N 24221234 and/or envelopes, P/N 2XJ 19572 In Canada

- DGN Marketing Services LTD.


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 383
Chevrolet Venture V6-3.4L VIN E 2708

- Phone 800-668-5539 or Fax 905-670-5777

- For form DGN P/N 150-0-0-532 and/or envelopes, P/N DGN 150-0-0-533

Important:
The see-through envelope should be attached to the sides of the top half of the transmission shipping container at either of the small ends. DO
NOT PUT THE ENVELOPE ON THE TOP SURFACE OF THE SHIPPING CONTAINER BECAUSE IT CANNOT BE READ WHEN THE
TRANSMISSIONS ARE STACKED IN THE WAREHOUSE OR THE RETURN FORM MAY BECOME DAMAGED/LOST IN THE
SHIPPING PROCESS.

Dealership Process of the Feedback Form For New Vehicle, Goodwrench Parts Warranty, Customer Pay and Over-The-Counter Sales.

For New Vehicle warranty claims, Goodwrench Parts Warranty or Customer Pay repairs, perform the following:

1. Remove the new feedback form from the information packet shipped with the replacement transmission.

2. Complete all the fields in the top third of form and check the appropriate boxes.

3. INSERT THE ORIGINAL COPY OF THE FORM IN THE SEE-THROUGH ENVELOPE SO THAT THE INFORMATION ON THE
COMPLETED FORM IS VISIBLE.

4. Attach the dealer copy of the feedback form to the dealer repair order hard copy.

5. Return the transmission core to the parts department for return to GM.

For Over-the-Counter Sales, include the following:

^ The Dealer Code

^ The Dealer Phone Number

^ Print the letters "OTC" on the form in large letters (to indicate "over the counter sale".

These new feedback forms are critical to General Motors goal of producing the most reliable and durable transmissions for General Motors cars and
trucks. With properly completed forms, General Motors can quickly identify and correct the manufacturing defects, thereby providing the highest
quality automatic transmissions for you and your customers.

The General Motors Labor Time Guide includes time allowance for completing the feedback form in the base time for K7000.Technical Service
Bulletin # 02-07-30-028 Date: 020601

A/T - Serial Number/Site Code Locations/Identification


File In Section: 07 - Transmission/Transaxle

Bulletin No.: 02-07-30-028

Date: June, 2002

INFORMATION

Subject:
Automatic Transmission Serial Number and Site Code Locations

Models:
2003 and Prior Passenger Cars and Trucks
2003 HUMMER H2
with North American Automatic Transmissions

General Motors automatic transmissions fall into two categories: those manufactured "by GM" (OEM) and those manufactured "for GM"
(REMAN). Only OEM transmissions are used in the production of new GM vehicles. Goodwrench(R) service transmissions can be either OEM or
REMAN. All Goodwrench(R) REMAN transmissions are identified by a green metal tag with the words "Manufactured for GM" except for
Allison(R), 4L30E (Catera) and 5L40E (CTS).

^ OEM = blue or black tag = "by GM"

^ REMAN = green tag = "for GM" (except for Allison®, Catera and CTS)

Remanufactured Transmission Serial and Site Code Number Locations


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 384
Chevrolet Venture V6-3.4L VIN E 2709

Other than the exceptions shown above, all North American Remanufactured transmissions use the same green tag shown.

Important:
When reporting serial and site code numbers, use the top row of characters followed by the bottom row with no spaces between any of these
characters. Refer to the example below.

The Allison(R) built transmissions, as well as the 4L30E (Catera) and 5L40 (CTS) do not have green REMAN tags. Refer to the appropriate section
in this bulletin for each of these transmissions' correct OEM and REMAN serial numbers.

OEM Transmission Serial and Site Code Number Locations

Front Wheel Drive Transmissions


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 385
Chevrolet Venture V6-3.4L VIN E 2710
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 386
Chevrolet Venture V6-3.4L VIN E 2711
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 387
Chevrolet Venture V6-3.4L VIN E 2712
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 388
Chevrolet Venture V6-3.4L VIN E 2713
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 389
Chevrolet Venture V6-3.4L VIN E 2714

The transmission ID tag is usually located on the side of the case facing the rear of the vehicle.

Allison(R) 1000 Series (OEM) M74


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 390
Chevrolet Venture V6-3.4L VIN E 2715

The Allison(R) LCT 1000 automatic transmission ID tag (1) is located on the right (passenger side), just rear of the PTO (power take off) cover.

Use the model number (1), the date of manufacture number (2) and the serial number (3) for reporting purposes. For example:
1000XXXXXYYYYYYYYYY (1000 + 5 characters + 10 characters).

DISCLAIMERTechnical Service Bulletin # 03-07-30-017 Date: 030501

A/T - Grinding Noise/No Vehicle Movement in 'D' or 'R'


File In Section: 07 - Transmission/Transaxle

Bulletin No.: 03-07-30-017

Date: May, 2003

TECHNICAL

Subject:
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 391
Chevrolet Venture V6-3.4L VIN E 2716
Grind Noise or No Vehicle Movement when Shifting into Drive or Reverse (Inspect Transaxle, Replace Various Transaxle Components)

Models:
1999-2002 Buick Century, LeSabre, Park Avenue
2002 Buick Rendezvous
1999-2002 Chevrolet Monte Carlo, Venture
2000-2002 Chevrolet Impala
1999-2002 Oldsmobile Intrigue, Silhouette
1999-2002 Pontiac Bonneville, Grand Prix, Montana
2001-2002 Pontiac Aztek
with Transaxle Auto 4-SPD, 4T65-E (RPO MN3)

Condition

Some customers may comment on a grinding noise when shifting into DRIVE or REVERSE or the vehicle will not move in DRIVE or REVERSE.

Correction

Important:
^ If the vehicle DOES NOT exhibit a grinding condition but DOES exhibit shifting concerns, refer to Corporate Bulletin # 00-07-30-002.

^ When servicing the transaxle side cover gasket, refer to Corporate Bulletin # 01-07-30-032.

^ When servicing the valve body spacer plate and/or gasket, refer to informational Corporate Bulletin # 02-07-30-014.

^ When servicing or replacing the transaxle resulting from this condition, the transaxle cooler MUST be flushed. Refer to informational
Corporate Bulletin # 02-07-30-052.

Follow the service procedure below for diagnosis and correction of the grinding noise condition.

Important:
If metallic debris is found on the transaxle pan magnet, the transaxle must be completely disassembled and cleaned. Failure to properly
clean the transaxle case and internal components may lead to additional unnecessary repeat repairs.

1. Remove the transaxle oil pan and inspect the magnet in the bottom of the pan for metal debris. Refer to SI Document ID # 414136.

2. Remove the transaxle from the vehicle. Refer to the appropriate SI document.

Important:
^ Inspect all the transaxle components for damage or wear. Replace all damaged or worn components. The parts listed below should be
sufficient to correct this concern.

^ This condition does not normally require replacement or reconditioning of the transaxle completely unless there is extensive damage.
Components such as clutches, valve body and torque convertors WILL NOT require replacement to correct this condition.

3. Disassemble the transaxle. Refer to the Transmission Overhaul procedure in Unit Repair, SI Document ID # 633950.
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 392
Chevrolet Venture V6-3.4L VIN E 2717

^ (668) Input Sun Gear, P/N 24204098

^ (672) Input Complete Carrier Assembly, P/N 24204430

^ (674) Input/Reaction Carrier Thrust Bearing Assembly, P/N 24205127

^ (675) Reaction Complete Carrier Assembly, P/N 8646504

^ (676) Reaction Carrier/Sun Gear Thrust Bearing Assembly, P/N 8649353

4. Replace the parts listed above to correct this condition. Refer to Unit Repair Manual, Transmission Overhaul procedure, SI Document ID #
417561; Input and Third Sprag Clutches Disassemble, SI Document ID # 38901; and Input and Third Sprag Clutches Assemble, SI
Document ID # 60415.

5. When servicing or replacing the transaxle resulting from this condition, the transaxle cooler MUST be flushed. Refer to informational
Corporate Bulletin # 02-07-30-052.

Parts Information

Parts are currently available from GMSPO.

Warranty Information
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 393
Chevrolet Venture V6-3.4L VIN E 2718

For vehicles repaired under warranty, use the table.

Important:
^ The recondition transaxle add time is not applicable for this repair. All of the transaxle clutch packs and bushings have not been replaced.

^ The recondition transaxle Carrier/Differential Final Drive Assemble is not applicable for this repair.

DisclaimerTechnical Service Bulletin # 01-07-30-041B Date: 051006

A/T - Diagnosing Fluid Leaks


Bulletin No.: 01-07-30-041B

Date: October 06, 2005

INFORMATION

Subject:
Transmission Fluid Leak Diagnosis

Models:
2006 and Prior Passenger Cars and Light Duty Trucks
2003-2006 HUMMER H2
2006 HUMMER H3
2005-2006 Saab 9-7X

with Hydra-Matic(R) and Allison(R) LCT 1000 Automatic Transmissions

Supercede:

This bulletin is being revised to add the 2006 model year, HUMMER H3 and Saab 9-7X vehicles. Please discard Corporate Bulletin Number
01-07-30-041A (Section 07 - Transmission/Transaxle).

The purpose of this bulletin is to provide assistance for technicians when diagnosing fluid leaks on automatic transmissions. It has been found that
many of the transmissions returned to the Warranty Parts Center (WPC) for fluid leaks were determined to be no trouble found (fluid leaks could
not be found). To reduce unnecessary transmission replacement, please use the following information.

If the customer concern is a leak, the source of the leak must be isolated. There are many components on a vehicle that can produce leaks:

^ Engine oil

^ Engine coolant

^ Power steering

^ Transmission

^ Rear differential

^ Front differential

^ Transfer case

It is important to note that leaking fluids can migrate toward the rear of the vehicle. This can make isolating the leak very difficult. Generally, the
fluid path can be followed to the leaking component during a visual inspection. Once the leaking component has been identified, use the J 42220
Leak Detection Lamp and the J 28431-6 Leak Dye Kit to isolate the leak point.
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 394
Chevrolet Venture V6-3.4L VIN E 2719

If the leaking component cannot be identified, use the leak dye in components that are in the fluid path. The Service Information contains
procedures for diagnosing leaks and also alternate methods for leak detection.

Most leaks at seals and gaskets can be repaired on-vehicle. These procedures are located in the appropriate sub-section of the Service Manual and
use the time from the applicable Labor Time Guide (LTG). If the transmission case is leaking due to porosity, the transmission typically needs to be
replaced.

All components that are diagnosed and that require replacement due to leakage must be diagnosed with the leak dye and a leak detection lamp.

Upon receipt and inspection at/by WPC, components that do not exhibit leaks will be brought to the attention of the Regional Warranty Manager
for appropriate action.

DisclaimerTechnical Service Bulletin # 00-08-46-002A Date: 050412

OnStar(R) - Cellular Antenna Replacement Parts


Bulletin No.: 00-08-46-002A

Date: April 12, 2005

INFORMATION

Subject:
OnStar(R) System Cellular Antenna Replacement Parts Availability

Models:
1996-2005 Passenger Cars and Light Duty Trucks
2003-2005 HUMMER H2

with OnStar(R) and Glass Mounted Antennas

Supercede:

This bulletin is being revised to update the model years, models and parts information. Please discard Corporate Bulletin Number 00-08-46-002
(Section 08 - Body & Accessories).

Replacement parts for the OnStar(R) system cellular antenna are available as follows:

^ Cellular Antenna Kit - If the antenna mast or exterior base is damaged or missing or if the antenna base has separated from the exterior glass
surface.

^ Cellular Antenna Inner Coupling - If the antenna coupling on the inside of the glass requires replacement.

Important:
If glass replacement is required, both the Cellular Antenna Kit and the Cellular Antenna Inner Coupling are required. The kits listed contain all
the necessary parts and instructions needed to properly install a new cellular antenna exterior base or interior coupling to the glass surface. To
obtain maximum adhesion during installation, the instructions included in the kits must be followed carefully and exactly as written.

Important:
Do not attempt to reinstall the original cellular antenna exterior base or interior coupling using any type of glue, adhesive tapes, etc. Doing so
may eliminate the cellular signal transfer through the glass and reduce the maximum performance of the system that includes air bag
deployment notification.

Important:
To obtain maximum adhesion between the new cellular exterior base or interior coupling and the glass surface, the base, coupling and glass
must be kept dry and above 15°C (60°F) during the installation and for the 24 hours immediately following the installation. Not keeping the
vehicle dry and above the temperature listed for 24 hours may result in the new cellular antenna exterior base or interior coupling coming off.
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 395
Chevrolet Venture V6-3.4L VIN E 2720

Parts Information

Parts are currently available from GMSPO.

DisclaimerTechnical Service Bulletin # 00-08-46-003B Date: 050209

Instruments - GPS System Performance Degradation


Info - Global Position Sensor (GPS) Performance Degradation # 00-08-46-003B - (Feb 9, 2005)

Models:
1996-2005 Passenger Cars and Trucks
2002-2005 Saturn Vehicles

with Navigation Systems and/or OnStar(R)

This bulletin is being revised to include additional information. Please discard Corporate Bulletin Number 00-08-46-003A (Section 08 - Body and
Accessories).

Navigation and OnStar(R) systems require a GPS antenna in order to function properly. This antenna may be located inside the vehicle. If the GPS
antenna is located inside the vehicle, performance of the system may be compromised by window tinting film.

If the GPS system performance is in question and the vehicle has window tinting, a quick diagnostic check can be made by temporarily moving the
GPS antenna to an external vehicle surface, such as the decklid or roof. If the GPS function of the navigation or On Star(R) system operates
normally with the antenna relocated the repair would not be considered a warranty repair. The subsequent repair procedure or GPS placement
would be up to the customer.

Some vehicles have the GPS antenna located on the rear window shelf Objects placed on the rear window shelf such as tissue boxes, books, dolls,
etc,, also have the potential to interfere with GPS performance.

Warranty Information

Repairs made to the vehicle navigation and/or OnStar(R) system, which are the result of window tinting, are not considered warranty repairs.

DisclaimerTechnical Service Bulletin # 04-06-01-013 Date: 040401

Engine - Serpentine Drive Belt Wear Information


Bulletin No.: 04-06-01-013

Date: April 29, 2004

INFORMATION
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 396
Chevrolet Venture V6-3.4L VIN E 2721

Subject:
Information on Serpentine Belt Wear

Models:
2004 and Prior Passenger Cars and Trucks
2003-2004 and Prior HUMMER H2

All current GM vehicles designed and manufactured in North America were assembled with serpentine belts that are made with an EPDM material
and should last the life of the vehicle. It is extremely rare to observe any cracks in EPDM belts and it is not expected that they will require
maintenance before 10 years or 240,000 km (150,000 mi) of use.

Older style belts, which were manufactured with a chloroprene compound, may exhibit cracks depending on age. However, the onset of cracking
typically signals that the belt is only about halfway through its usable life.

A good rule of thumb for chloroprene-based belts is that if cracks are observed 3 mm (1/8 in) apart, ALL AROUND THE BELT, the belt may be
reaching the end of its serviceable life and should be considered a candidate for changing. Small cracks spaced at greater intervals should not be
considered as indicative that the belt needs changing.

Any belt that exhibits chunking should be replaced.

DisclaimerTechnical Service Bulletin # 04-07-30-037B Date: 060612

A/T - DEXRON(R) VI Fluid Availability


Bulletin No.: 04-07-30-037B

Date: June 12, 2006

INFORMATION

Subject:
Release of DEXRON(R) VI Automatic Transmission Fluid (ATF)

Models:
2007 and Prior Passenger Cars and Light Duty Trucks
2003-2007 HUMMER H2
2006-2007 HUMMER H3
2005-2007 Saturn Relay
2005 and Prior Saturn L-Series
2005-2007 Saturn ION
2005-2007 Saturn VUE with 4T45-E
2005-2007 Saab 9-7X

Except 2007 and Prior Chevrolet Aveo, Epica, Equinox, Optra


Except 2007 and Prior Pontiac Torrent, Vibe, Wave
Except 2003-2005 Saturn ION with CVT or AF23 Only
Except 1991-2002 Saturn S-Series
Except 2007 and Prior Saturn VUE with CVT, AF33 or 5AT (MJ7/MJ8) Transmission Only

Supercede:

This bulletin is being updated with the 2007 model year. Please discard Corporate Bulletin Number 04-07-30-037A (Section 07 -
Transmission/Transaxle).

DEXRON(R)-VI ATF

General Motors Powertrain has recently upgraded to DEXRON(R)-VI ATF with the start of 2006 vehicle production.

Only 2005 and prior models that currently use DEXRON(R)-III may use DEXRON(R)-VI as a replacement.

All 2006 and future models that use DEXRON(R)-VI are to be serviced with DEXRON(R)-VI fluid only.
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 397
Chevrolet Venture V6-3.4L VIN E 2722

DEXRON(R)-VI is an improvement over DEXRON(R)-III in the areas shown.

2006-2007 Transmission Fill and Cooler Flushing

Some new applications of the 6L80 six speed transmission will require the use of J 45096 - Flushing and Flow Tester to accomplish transmission
fluid fill. It is highly recommended that the clean oil reserve of the machine be purged of DEXRON(R)-III and filled with DEXRON(R)-VI.

Parts Information

Disclaimer
Technical Service Bulletin # 04-01-37-001 Date: 040106

A/C - Control Knob Replacement Availability


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 398
Chevrolet Venture V6-3.4L VIN E 2723
Bulletin No.: 04-01-37-001

Date: January 06, 2004

INFORMATION

Subject:
HVAC Control Knob Replacement

Models:
2000-2004 All Passenger Cars and Light Duty Trucks
2003-04 HUMMER H2

HVAC Control Knob Availability

Important:
If a knob becomes loose or broken, you MUST first check for availability of the control knob before attempting to replace the entire HVAC
controller.

The various knobs used on the HVAC controls of most GM vehicles are available for purchase separately from the HVAC head units. If a knob
becomes loose or broken, you MUST first check for availability of the control knob before attempting to replace the entire HVAC controller. Please
use only the labor operation code listed below when replacing an HVAC control knob.

Warranty Information

For vehicles repaired under warranty, use the table.

Disclaimer
Technical Service Bulletin # 99-08-45-005 Date: 991101

Accessory Receptacle/Cigar Lighter - Inoperative


File In Section: 08 - Body and Accessories

Bulletin No.: 99-08-45-005

Date: November, 1999

TECHNICAL

Subject:
Accessory Receptacle/Cigar Lighter is Inoperative (Check Aftermarket Device Plug for Short to Ground)

Models:
1995-2000 Passenger Cars and Trucks

Condition

Some customers may comment that the cigar lighter or the accessory receptacle is inoperative; or that the internal fuse (within the plug on an
aftermarket device), blows intermittently.

Cause
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 399
Chevrolet Venture V6-3.4L VIN E 2724

Certain aftermarket devices have a newly designed power plug with an internal mini fuse. The mini fuse may have an external terminal (which may
be used to externally check the fuse). If the mini fuse external test terminal is not recessed into the mini fuse body, it may come in contact with the
shell of the vehicle receptacle and cause the fuse (of either the vehicle or the aftermarket device), to blow intermittently.

Correction

Test the aftermarket device plug for short to ground. The following step may be performed at the customer's expense. As this is not a defect in
material, design or workmanship of the vehicle, it would be the owner's responsibility.

1. Place a piece of tape over the mini fuse terminal temporarily.

2. Explain to the customer that the fuse for the device must have no exposed terminals, and that finding one would be his responsibility.

3. Refer the customer to the manufacturer of the aftermarket device for a new plug.
Technical Service Bulletin # 00-07-30-007A Date: 020201

A/T - 4T65E, MIL ON/Whine Noise In PARK/NEUTRAL


File In Section: 07 - Transmission/Transaxle

Bulletin No.: 00-07-30-007A

Date: February, 2002

TECHNICAL

Subject:
Whine Noise In Park Or Neutral, Service Engine Soon or Service Vehicle Soon Lamp Illuminates (Replace Drive Sprocket Support Bearing)

Models:
1999-2000 Buick LeSabre, Park Avenue/Ultra, Regal, Riviera
1999-2000 Chevrolet Lumina, Monte Carlo, Venture
2000 Chevrolet Impala
1999 Oldsmobile Eighty Eight
1999-2000 Oldsmobile Intrigue, Silhouette
1999-2000 Pontiac Bonneville, Grand Prix, Montana
with 3.4L, 3.5L or 3.8L Engine (VINs E, H, K, 1-- RPOs LA1, LX5, L36, L67)
and Hydra-Matic 4T65-E Transaxle/Transmission (RPOs MN3, MN7, M15)

This bulletin is being revised to add the Chevrolet Impala to the models affected. Please discard Corporate Bulletin Number 00-07-30-007 (Section
07 - Transmission/Transaxle).
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 400
Chevrolet Venture V6-3.4L VIN E 2725

Condition

Some owners of the listed models equipped with a Hydra-Matic 4T65-E transaxle with a Julian Date prior to 0045 may comment on a whine noise
in PARK and/or NEUTRAL or a Service Engine Soon or Service Vehicle Soon lamp that is illuminated. Upon investigation, a DTC P0741 or
P0742 may be found.

Cause

The above condition may be due to drive sprocket support bearing fluting and/or bearing failure.

Correction

Replace the drive sprocket support bearing. Inspect the channel plate and drive sprocket for any abnormal wear, Turbine shaft for cut seals and/or
nicks, and chain for excessive play due to failed bearings.

Important:
When installing the new bearing, the part number MUST be visible (facing upward). Before installing the drive sprocket, lubricate the bearing
assembly with J 36850 assembly lubricant.

Refer to the 4T65-E Unit Repair Section for the installation procedure.

Service Parts Information

Parts are currently available from GMSPO.

Warranty Information

For vehicles repaired under warranty, use the table.


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 401
Chevrolet Venture V6-3.4L VIN E 2726

DisclaimerTechnical Service Bulletin # 00-00-90-001 Date: 001101

Suspension - Chassis Lubrication Importance


File In Section: 00 - General Information

Bulletin No: 00-00-90-001

Date: November, 2000

INFORMATION

Subject:
The Importance of Chassis Lubrication

Models:
2001 and Prior Passenger Cars and Trucks

An Explanation of Required Lubrication


It is important to note that many General Motors trucks and sport utility vehicles do not have the "lubed for life" suspension systems that are
becoming common on the passenger cars. It is vital to the longevity of the suspension components that proper lubrication be received at the
specified intervals. Extra attention should be given to the ball joints to assure they receive regular greasing.

A Visual Inspection is Not Enough

Many combinations of grease fittings and sealed components may be found on the chassis of General Motors vehicles. The lubrication required for
each vehicle can be located in the Maintenance and Lubrication sub-section of General Information in the Service Manual. This section outlines all
lubrication required for the vehicle and also provides chassis diagrams of grease points. Please refer to the maintenance schedule for the
recommended service intervals.

DisclaimerTechnical Service Bulletin # 02-06-01-008 Date: 020301

Engine - New Prelube Tool


File In Section: 06 - Engine/Propulsion System

Bulletin No.: 02-06-01-008

Date: March, 2002

INFORMATION

Subject:
Information on a New Engine Preluber Tool

Models:
1990-2002 All Cars and Light Duty Trucks
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 402
Chevrolet Venture V6-3.4L VIN E 2727

A new engine Preluber tool has been developed as an essential tool. This tool will be automatically shipped to all tier one and tier two dealerships.
The new tool is known as J-45299 ENGINE PRELUBER.

The J-45299 ENGINE PRELUBER consists of a two gallon container, hand pump, flexible hose, adapter set and a two sided laminated instruction
sheet. The engine preluber will inject clean engine oil into the engine oiling system. Following the instructions included with the tool will allow the
main bearings, connecting rod bearings and the oil pump to be properly lubed.

When prelubing the engine with more than the minimum recommended amount of oil, the camshaft bearings and other valve train components may
also be lubricated.

Notice:
Neglecting to prelube or improperly prelubing a new, remanufactured or serviced engine prior to the initial start-up may lead to premature
bearing failure in the engine.

This tool should be used when installing a new engine, remanufactured engine or an overhauled engine. This tool and procedure should also be
used when the crankshaft or connecting rods have been removed from the engine for any reason.

Any dealers or other interested parties can purchase this tool directly from Kent Moore by calling 1-800-345-2233.

DisclaimerTechnical Service Bulletin # 06-03-10-004 Date: 060301

Tires/Wheels - Wheel Weight Usage Precautions


Bulletin No.: 06-03-10-004

Date: March 01, 2006

INFORMATION

Subject:
Proper Use of OEM Service Wheel Weights, Marring and/or Damage Due to Use of Non-OEM and/or Incorrect Wheel Weight Installation

Models:
2007 and Prior GM Cars and Light Duty Trucks
2003-2007 HUMMER H2
2006-2007 HUMMER H3
2005-2007 Saab 9-7X

Note:
It is critical to use the proper OEM wheel weights when service requires balancing of the tire/wheel assemblies. Failure to use the proper OEM
wheel weights may result in damage/marring to the wheel assembly that will NOT be covered under the vehicles warranty.

Service OEM wheels weights are currently available from GMSPO.


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 403
Chevrolet Venture V6-3.4L VIN E 2728

Important:
When balancing factory aluminum wheels with clip-on wheel balance weights, be sure to use special polyester-coated weights. These coated
weights reduce the potential for corrosion and damage to aluminum wheels.

These coated weights reduce the potential for corrosion and damage to aluminum wheels.

^ MC (1) and AW (2) series weights are approved for use on aluminum wheels.

^ P (3) series weights are approved for use on steel wheels only.

^ T (4) series coated weights are approved for use on both steel and aluminum wheels.

Important:
Use a nylon or plastic-tipped hammer when installing coated clip-on wheel balance weights to minimize the possibility of damage to the
polyester coating.

The contour and style of the wheel rim flange will determine which type of clip-on wheel weight (1) should be used. The weight should follow the
contour of the rim flange. The weight clip should firmly grip the rim flange.

Wheel Weight Placement - Clip-on Weights


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 404
Chevrolet Venture V6-3.4L VIN E 2729

When static balancing, locate the wheel balance weights on the inboard flange (2) if only 28 g (1 oz) or less is called for. If more than 28 g (1 oz) is
called for, split the weights as equally as possible between the inboard (2) and outboard (1) flanges.

When dynamic balancing, locate the wheel balance weights on the inboard (2) and outboard (1) rim flanges at the positions specified by the wheel
balancer.

Important:
When installing adhesive balance weights on flangeless wheels, do NOT install the weight on the outboard surface of the rim. Adhesive wheel
balance weights may be used on factory aluminum wheels.

DisclaimerTechnical Service Bulletin # 01-00-89-013 Date: 010901

RKE Transmitter - Correct Use of Labor Operation R4490


File In Section: 00 - General Information

Bulletin No.: 01-00-89-013

Date: September, 2001


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 405
Chevrolet Venture V6-3.4L VIN E 2730

WARRANTY ADMINISTRATION

Subject:
Correct Use of Labor Operation R4490, RKE Transmitter, Replace

Models:
2002 and Prior Passenger Cars and Light Duty Trucks

This bulletin is being issued to ensure the correct use of the labor operation R4490 (Transmitter, Remote Door/Rear Compartment Lock - Replace).
This labor operation should be used for diagnosis, replacement and reprogramming of defective RKE transmitters. Some specific non-warranty
situations are addressed as follows:

Missing or Incorrect Remote Keyless Entry from Carrier

A missing or incorrect Remote Keyless Entry (RKE) transmitter should be noted on the carrier delivery receipt when the vehicle is delivered to the
dealership. Refer to GM Service Policies and Procedures Manual, article 2.1.8, Incorrect Part and/or Invoice Option (in Canada, refer to article
2.2.7, New Vehicles Received with Missing or Incorrect Parts/Options) and submit the appropriate transportation claim.

RKE Programming Before Delivery of the Vehicle

If the RKE transmitter requires reprogramming prior to delivery because transmitters were mixed with other vehicles in inventory, it should be done
as part of the Pre-Delivery Inspection (PDI). The dealership inventory control process should match the RKE transmitter with the correct vehicle.
Please note that RKE transmitter reprogramming or replacement as a result of mis-matched transmitters should not be submitted as a warranty
claim.

DisclaimerTechnical Service Bulletin # 01-09-40-002 Date: 010601

Seat Belt System - Collision Replacement Guidelines


File In Section: 09 - Restraints

Bulletin No.: 01-09-40-002

Date: June, 2001

INFORMATION

Subject:
Seat Belt System Replacement Guidelines for Vehicles Involved in Collisions

Models:
2002 and Prior Passenger Cars and Trucks

The following information should be used as guidelines for determining if seat belt system components require replacement after a vehicle has been
involved in a collision.

Caution:
Restraint systems can be damaged in a collision. To help avoid injury and ensure that all parts in need of replacement are replaced:

Replace any seat belt system that was in use during a collision serious enough to deploy any automatic restraint device such as air bags and seat belt
pretensioners. This not only includes seat belt systems in use by people of adult size, but seat belt systems used to secure child restraints, infant
carriers and booster seats, including LATCH* system and top tether anchorages.

^ Replace any seat belt system that has torn, worn, or damaged components. This not only includes adult seat belt systems, but built-in child
restraints and LATCH system components, if any.

^ Replace any seat belt system if you observe the words "REPLACE" or "CAUTION", or if a yellow tag is visible. Do not replace a seat belt
system if only the child seat caution label is visible.

^ Replace any seat belt system if you are doubtful about its condition. This not only includes adult seat belt systems, but built-in child
restraints, LATCH system components, and any restraint system used to secure infant carriers, child restraints and booster seats.
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 406
Chevrolet Venture V6-3.4L VIN E 2731

Do NOT replace single seat belt system components in vehicles that have been in a collision as described above. Always replace the entire seat belt
system with the buckle, guide and retractor assembly, which includes the latch and webbing material. After a minor collision where no automatic
restraint device was deployed, seat belt system replacement may not be necessary, unless some of the parts are torn, worn, or otherwise damaged.

* LATCH is the industry-standard acronym for the built-in child restraint securing system - Lower Anchorages and Top Tethers for Children. Latch
consists of the top strap anchors in the vehicle, as well as the built-in "receivers" for LATCH-equipped, aftermarket child restraints.

DISCLAIMERTechnical Service Bulletin # 02-08-48-001B Date: 060329

Body - Urethane Adhesives for Glass Applications


Bulletin No.: 02-08-48-001B

Date: March 29, 2006

INFORMATION

Subject:
Urethane Adhesives for Stationary Glass and Other Applications

Models:
2007 and Prior GM Passenger Cars and Trucks (Including Saturn)
2007 and Prior Isuzu Trucks
2003-2007 HUMMER H2
2006-2007 HUMMER H3

Supercede:

This bulletin is being revised to update the models and model years and update the information for Canada. Please discard Corporate Bulletin
Number 02-08-48-001A (Section 08 - Body and Accessories).

Effective with the sale of existing stock, General Motors will no longer offer the URETHANE ADHESIVE KIT P/N 12346392 (which includes all
associated primers). Until this stock is depleted, the GM kit is still recommended. In Canada, the GM Urethane Adhesive Kit, P/N 10952983, which
includes all associated primers, is also being discontinued and will no longer be available after current stock is depleted. It is anticipated that stock
will be exhausted no later than May 21, 2006.

As an alternative to the GM Kit for bonded glass installation AND some exterior body panels on specific GM vehicles, various aftermarket
materials are recognized as meeting the equivalent of the GM performance specification. This specification (GM 3651G, recently updated) outlines
material performance requirements and tests for adhesive manufacturers who develop and manufacture Stationary Glass Urethane adhesives.

Those products currently recognized as meeting those equivalencies are as follows:

^ Dow Automotive (Essex) 400HV (one part and requires associated primers)

^ Dow Automotive (Essex) U216 (two part and requires associated primers) Call Dow Automotive at 1-800-453-3779 for more information.

^ 3M(TM) "Fast Cure" Auto Glass Urethane (one part and requires associated primers) Call 3M(TM) at 1-877-666-2277 for more information.

Any use of these materials should be done as a system by the specific manufacturer. DO NOT intermix primers or adhesives from one manufacturer
to another.

DisclaimerTechnical Service Bulletin # 01-00-89-009 Date: 010501

Key/Key Number/Security Chip - Replacement


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 407
Chevrolet Venture V6-3.4L VIN E 2732
File In Section: 00 - General Information

Bulletin No.: 01-00-89-009

Date: May, 2001

INFORMATION

Subject:
Replacement of Keys, Key Numbers and/or Security Chips

Models:
2002 and Prior Passenger Cars and Trucks

General Motors has received reports from dealers and law enforcement officials in various parts of the country regarding a new trend in auto theft.

The current mode of operation is for a person (thief) to do the following:

1. Pick out the vehicle he/she wishes to steal from a new/used car sales facility or off the street.

2. Record the Vehicle Identification Number (VIN).

3. Take the VIN to any dealership which cuts keys. In some instances they have presented hand-written registration forms as proof of
ownership.

4. The thief then returns and drives the vehicle from the location.

Cutting of replacement keys is serious business. General Motors Policies and Procedures Manual, Section 3.2.5 (3.1.6 in Canada), Replacement of
Key Numbers & Security Chips, provides the following guidelines: "For security-and protection against auto theft, dealer should verify vehicle
ownership before providing replacement keys, key numbers and/or security chips. Verification should include positive identification of requester
and verification of vehicle ownership through registration."

Each dealership should (if they are in the business of cutting keys for walk-in, phone, fax, or other requesters) make a permanent file, by VIN, of all
key requests. Copies of the following documents should remain in each file:

- Government-issued picture ID (for example, a driver's license)

- Registration or other proof of ownership Registration should have normal markings from the state/province which issued the registration and
possibly the receipt for payment recorded as well. Since each state/province will be different, you will need to set up guidelines for your
dealership based on the current registration laws and or policies of your state/province. We know of no law enforcement agency or
state/province vehicle registration office which will accept a hand-written registration document.

- Copy of the paid customer receipt which has the name of the employee who cut and sold the key to the customer

- When vehicle ownership cannot be proven beyond a reasonable doubt, Do NOT provide the keys. Refer the customer to the selling dealer or
GM Roadside Assistance.

Important:
^ When a dealership calls the TRACS 2000 voice response system (Vintage Group in Canada) for key codes, the dealer code is recorded by
VIN, in a permanent electronic file.
^ Cutting keys for anyone other than the registered vehicle owner may result in the dealership and/or employee being charged with aiding and
abetting in grand theft auto and determined to be liable, in the event the vehicle is subsequently stolen from another dealership or customer.

Dealers may wish to designate one specific, trusted employee as the person to handle all key requests.

DISCLAIMERTechnical Service Bulletin # 03-07-30-043A Date: 060525

A/T - Shift Lock Control Feature Function


Bulletin No.: 03-07-30-043A

Date: May 25, 2006


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 408
Chevrolet Venture V6-3.4L VIN E 2733

INFORMATION

Subject:
Information Regarding Automatic Transmission Shift Lock Control Function

Models:
2007 and Prior Passenger Cars and Trucks (Including Saturn)
2007 and Prior HUMMER H2, H3
2005-2007 Saab 9-7X

with Automatic Transmission

Supercede:

This bulletin is being revised to add models and model years. Please discard Corporate Bulletin Number 03-07-30-043 (Section 07 -
Transmission/Transaxle). This bulletin is being issued to better explain how the Automatic Transmission Shift Lock Control (formerly known as
Brake Transmission Shift Interlock (BTSI)) feature is intended to operate. Revised wording regarding the shift lock control system began appearing
in the Owner Manuals beginning with the 2004 model year.

The shift lock control feature was intended to prevent drivers from shifting out of Park with the vehicle running without the brakes applied.
However, if the ignition switch is in the Accessory (ACC) position, it may be possible on some vehicles to move the shift lever out of Park
WITHOUT first activating the brake.

The shift lock control system is ONLY active when the ignition switch is in the RUN or ON position. This means that when the ignition switch is in
the RUN or ON position, the shift lever cannot be moved out of the Park position without activating the brake.

Some owners may feel that the shift lock control system prevents an unattended child from moving the vehicle. Please stress to owners, as stated in
the Owner Manual, that children should NEVER be left unattended in a vehicle, even if the ignition key has been removed from the vehicle.

DisclaimerTechnical Service Bulletin # 00-07-30-002B Date: 020701

A/T - 4T65E Harsh Shifts/Shudders/Slips/DTC's Set


File In Section: 07 - Transmission/Transaxle

Bulletin No.: 0O-07-30-002B

Date: July, 2002

TECHNICAL

Subject:
Slips, Harsh Upshift or Garage Shifts, Launch Shudders, Flares, Erratic Shifts and Intermittent Concerns, DTC P1811 or P0748 Set (Replace
Pressure Control Solenoid Valve Assembly)

Models:
1997-1999 Buick Riviera
1997-2002 Buick Park Avenue
1998-2002 Buick LeSabre
1999-2002 Buick Regal
2000-2002 Buick Century
2002 Buick Rendezvous
1997-2001 Chevrolet Lumina
1997-2002 Chevrolet Monte Carlo
1999-2002 Chevrolet Venture
2000-2002 Chevrolet Impala
1997-1999 Oldsmobile Eighty Eight
1997-2002 Oldsmobile Silhouette
1998-2002 Oldsmobile Intrigue
2001-2002 Oldsmobile Aurora (3.5L)
1997-2002 Pontiac Bonneville, Grand Prix
1999-2002 Pontiac Transport/Montana
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 409
Chevrolet Venture V6-3.4L VIN E 2734
2001-2002 Pontiac Aztek
with Hydra-Matic 4T65-E (RPOs MN3, MN7, M15, M76)

This bulletin is being revised to add additional models and model years. Please discard Corporate Bulletin Number 00-07-30-002A (Section 07 -
Transmission/Transaxle).

Condition

Some owners of the above vehicles with a HydraMatic 4T65-E transaxle may comment on harsh upshifts or harsh garage shifts, soft shifts,
shudders on hard acceleration, or shifts erratic. These conditions may appear intermittently or set a DTC P1811 or P0748. During diagnosis, a low
or high line pressure (actual versus desired) may be observed.

Cause

The above condition may be due to any one of the following which may affect line pressure output:

^ Sediment inside the pressure control (PC) solenoid valve, causing the PC solenoid valve to mechanically bind.

^ Sediment in the valve body, causing the torque signal regulator valve to stick.

^ Incorrect transaxle oil level.

Correction

Important:
Any of the above conditions may be intermittent, therefore, this test should be performed at least three times.

Refer to the Line Pressure Check Procedure in SI, along with the Line Pressure Specification Table shown, to determine if actual versus desired
pressures are within the values specified. The Scan Tool is only able to control the PC solenoid valve in PARK and NEUTRAL with the vehicle
stopped. This protects the clutches from extremely high or low pressures in DRIVE or REVERSE ranges.

Refer to the Line Pressure Specification Table. The pressures in the table assume a temperature of 70°C. The pressure will vary with a change in
temperature.

If the actual versus desired pressures are not within the values specified, clean the valve body and replace the PC solenoid valve, if necessary.

Check the PC solenoid valve actual versus desired pressures to verify the new PC solenoid valve is responding correctly.

Refer to the Automatic Transaxle Section of the Service Manual for the proper repair procedure.

Line Pressure Check Procedure Tools Required

J 21867 Universal Pressure Gauge Set

Important:
Before performing a line pressure check, verify that the pressure control (PC) solenoid valve is receiving the correct electrical signal from the
PCM.

1. Install a Scan Tool.

Caution:
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 410
Chevrolet Venture V6-3.4L VIN E 2735
Keep the brakes applied at all times in order to prevent unexpected vehicle motion. Personal injury may result it the vehicle moves
unexpectedly.

2. Start the engine and set the parking brake.

3. Check for a stored Diagnostic Trouble Code (DTC).

4. Repair the vehicle, if necessary.

5. Check the fluid level. Refer to the Transmission Fluid Checking Procedure.

6. Check the manual linkage for proper adjustment.

7. Turn the engine OFF. Remove the oil pressure test hole plug and install the J 21867.

8. Put the gear selector in PARK range and set the parking brake.

9. Start the engine and allow the engine to warm up at idle.

Notice:
Total test running time should not be longer than two minutes, or else transmission damage could occur.

10. Access the PC solenoid valve control test on the Scan Tool.

11. Increase the PC solenoid as shown actual current from 0.0 to 1.0 amps in 0.1 amp increments. Allow the pressure to stabilize for five seconds
after each pressure change. Read the corresponding line pressure on the J 21867.

12. Refer to the Line Pressure specification table. Compare the data to the table.

13. If pressure readings differ greatly from the table, refer to Incorrect Line Pressure.

14. Remove the J 21867.

15. Apply sealant, P/N 12345382 (in Canada, P/N 10953489), to the oil pressure test hole plug.

Notice:
Refer to Fastener Notice in Cautions and Notices.
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 411
Chevrolet Venture V6-3.4L VIN E 2736

16. Install the oil pressure test hole plug.

Tighten

Tighten the oil pressure test hole plug to 12 N.m (106 lb in).

Parts Information

Parts are currently available from GMSPO.

Warranty Information

For vehicles repaired under warranty, use the table shown.

DISCLAIMERTechnical Service Bulletin # 02-07-30-048 Date: 021101

A/T - Pressure Control Solenoid Replacement


File In Section: 07 - Transmission/Transaxle

Bulletin No.: 02-07-30-048

Date: November, 2002

INFORMATION

Subject:
Pressure Control Solenoid Replacement for 4T65-E, 4T40-E, and 4T45-E Transaxle/Transmission

Models:
2000-2003 Buick Century, LeSabre, Park Avenue, Regal
2002-2003 Buick Rendezvous
2000-2001 Chevrolet Lumina
2000-2003 Chevrolet Cavalier, Impala, Malibu, Monte Carlo, Venture
2000-2002 Oldsmobile Intrigue
2000-2003 Oldsmobile Alero, Silhouette
2000-2003 Pontiac Bonneville, Grand Am, Grand Prix, Montana, Sunfire
2001-2003 Pontiac Aztek
with RPO Codes MN4, MN5, M13, M15, MN3, MN7 or M76

The pressure control solenoid in the above transaxles has changed for the 2003 models.

Important:
While the physical dimensions will allow usage of the new solenoid in past model transaxles or usage of the old solenoid in 2003 model
transaxles, they should not be interchanged. Interchanging of the pressure control solenoids will result in improper shift characteristics,
customer dissatisfaction, and needed repeat repairs.
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 412
Chevrolet Venture V6-3.4L VIN E 2737

When replacing a pressure control solenoid, be sure to use the correct part number.

Parts are currently available from GMSPO.

DisclaimerTechnical Service Bulletin # NHTSA04V597000 Date: 041221

Recall 04V597000: Power Sliding Door Interior Handle


MAKE/MODELS: MODEL/BUILD YEARS:

Chevrolet/Venture 1997-2005

Oldsmobile/Silhouette 1997-2004

Pontiac/Montana 1997-2005

Pontiac/Trans Sport 1999

Pontiac/Transport 1997-1998

MANUFACTURER: General Motors Corp.

NHTSA CAMPAIGN ID NUMBER: 04V597000 RECALL DATE: Dec 21, 2004

COMPONENT: Latches/Locks/Linkages: Doors: Latch

POTENTIAL NUMBER OF UNITS AFFECTED: 717302


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 413
Chevrolet Venture V6-3.4L VIN E 2738

SUMMARY:
On certain minivans equipped with second-row bucket seats or captain's chairs and a power sliding door on the passenger side of the vehicle, a
passenger using the interior handle to open the power sliding door could be injured.

CONSEQUENCE:
If a passenger uses the interior handle to open the power sliding door and holds onto the handle while it is being opened by the motor, the
passenger's arm may be pushed into the seat back or armrest and a wrist or lower arm injury may result.

REMEDY:
Dealers will replace the power sliding door interior handle on the passenger-side. If the vehicle is equipped with a power or manual sliding door on
the driver-side, the interior handle will also be replaced for appearance reasons. NOTE: Before the vehicle is serviced, GM advises owners to not
use the interior door handle to open the door. The driver can open and close the door from switches at the driver's position or by using the remote
key fob. The driver should tell passengers to use the switch located in front of the door to open or close it. The driver should use the override switch
to prevent operation of the power door by children or by others who are not familiar with its use. The recall is expected to begin in March 2005.
Owners should contact Chevrolet at 1-800-630-2438; Pontiac at 1-800-620-7668; or Oldsmobile at 1-800-630-6537.

NOTES:
GM recall No. 04110. Customers can also contact The National Highway Traffic Safety Administration's Auto Safety Hotline at
1-888-DASH-2-DOT (1-888-327-4236). Technical Service Bulletin # 04110 Date: 050524

Recall - Power Sliding Door Interior Handle Replacement


Right Hand Power Sliding Door Interior Handle
# 04110 - (May 24, 2005)

Models:
1997-2005 CHEVROLET VENTURE
1997-2004 OLDSMOBILE SILHOUETTE
1997-1998 PONTIAC TRANS SPORT
1999-2005 PONTIAC MONTANA

EQUIPPED WITH RIGHT-HAND POWER SLIDING DOOR AND SECOND ROW BUCKET SEATS OR CAPTAIN'S CHAIRS

DUE TO PART AVAILABILITY, THIS RECALL IS BEING ADMINISTERED IN PHASES. ALL VINS WILL BE LOADED INTO GMVIS:
HOWEVER, CUSTOMERS WILL BE NOTIFIED IN PHASES. YOU WILL BE NOTIFIED OF THE RELEASE OF ADDITIONAL PHASES
PRIOR TO CUSTOMER NOTIFICATION.

Condition

General Motors has decided that a defect, which relates to motor vehicle safety, exists in certain 1997-2005 Chevrolet Venture, 1997-2004
Oldsmobile Silhouette, 1997-1998 Pontiac Trans Sport, and 1999-2005 Pontiac Montana vehicles equipped with a right-hand power sliding door
and second row bucket seats or captains chairs. If a passenger uses the interior handle to open the power sliding door and holds onto the handle
while it is being opened by the door motor, the passenger's arm may be pushed into the seat back or armrest and a wrist or lower arm injury could
occur.

Until the vehicle is serviced, the interior handle should not be used to open the door. The driver can open and close the door from switches at the
driver's position or by using the remote key fob. The driver should tell passengers to use the switch located in front of the door to open or close the
door. The driver should also use the override switch to prevent operation of the power door by children or by others who are not familiar with its
use.

Correction

Although only the right-hand power sliding door handle requires replacement, dealers are to replace both rear door handles, if applicable, to keep
the appearance consistent

Vehicles Involved
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 414
Chevrolet Venture V6-3.4L VIN E 2739

Involved are certain 1997-2005 Chevrolet Venture, 1997-2004 Oldsmobile Silhouette, 1997-1998 Pontiac Trans Sport, and 1999-2005 Pontiac
Montana vehicles equipped with a right-hand power sliding door and second row bucket seats or captain's chairs, and built within these VIN
breakpoints shown.

Important:
Dealers should confirm vehicle eligibility through GMVIS (GM Vehicle Inquiry System) prior to beginning recall repairs. [Not all vehicles
within the above breakpoints may be involved.]

For US and Canada

For dealers with involved vehicles, a Campaign Initiation Detail Report containing the complete Vehicle Identification Number, customer name and
address data has been prepared and will be loaded to the GM DealerWorld (US) Recall Information, GMinfoNet (Canada) Recall Reports. Dealers
will not have a report available if they have no involved vehicles currently assigned.

For Export

For dealers with involved vehicles, a Campaign Initiation Detail Report containing the complete Vehicle Identification Number, customer name and
address data has been prepared, and is being furnished to involved dealers. Dealers will not receive a report with the recall bulletin if they have no
involved vehicles currently assigned.

The Campaign Initiation Detail Report may contain customer names and addresses obtained from Motor Vehicle Registration Records. The use of
such motor vehicle registration data for any purpose other than follow-up necessary to complete this recall is a violation of law in several
states/provinces/countries. Accordingly, you are urged to limit the use of this report to the follow-up necessary to complete this recall.
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 415
Chevrolet Venture V6-3.4L VIN E 2740

Parts Information

Parts required to complete this recall are to be obtained from General Motors Service Parts Operations (GMSPO). Please refer to your "involved
vehicles listing" before ordering parts. Normal orders should be placed on a DRO = Daily Replenishment Order. In an emergency situation, parts
should be ordered on a CSO = Customer Special Order.

Service Procedure

Tools Required

J 42506 Door Handle Clip Remover

1. Using the J 42506, Door Handle Clip Remover, remove the inside door handle clip.

2. Remove the inside handle from the sliding door and discard.

3. Load the clip into the inside door handle with the open end facing up.

4. Align the new handle with the shaft on the sliding door.

5. Press firmly in order to seat the inside handle on the sliding door.

6. Repeat the steps for the other door, if applicable.

Courtesy Transportation

The General Motors Courtesy Transportation Program is intended to minimize customer inconvenience when a vehicle requires a repair that is
covered by the New Vehicle Limited Warranty. The availability of courtesy transportation to customers whose vehicles are within the warranty
coverage period and involved in a product recall is very important in maintaining customer satisfaction. Dealers are to ensure that these customers
understand that shuttle service or some other form of courtesy transportation is available and will be provided at no charge. Dealers should refer to
the General Motors Service Policies and Procedures Manual for courtesy transportation guidelines.

Claim Information
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 416
Chevrolet Venture V6-3.4L VIN E 2741

Submit a Product Recall Claim with the information shown.

Customer Notification -- For US and Canada

General Motors will notify customers of this recall on their vehicle (see copy of customer letter shown in this bulletin).

Customer Notification -- For Export

Letters will be sent to known owners of record located within areas covered by the US National Traffic and Motor Vehicle Safety Act. For owners
outside these areas, dealers should notify customers using the sample letter shown.

Dealer Recall Responsibility -- For US and Export (US States, Territories, and Possessions)

The US National Traffic and Motor Vehicle Safety Act provides that each vehicle which is subject to a recall of this type must be adequately
repaired within a reasonable time after the customer has tendered it for repair. A failure to repair within sixty days after tender of a vehicle is prima
facie evidence of failure to repair within a reasonable time. If the condition is not adequately repaired within a reasonable time, the customer may
be entitled to an identical or reasonably equivalent vehicle at no charge or to a refund of the purchase price less a reasonable allowance for
depreciation. To avoid having to provide these burdensome remedies, every effort must be made to promptly schedule an appointment with each
customer and to repair their vehicle as soon as possible. In the recall notification letters, customers are told how to contact the US National
Highway Traffic Safety Administration if the recall is not completed within a reasonable time.

Dealer Recall Responsibility -- All

All unsold new vehicles in dealers' possession and subject to this recall MUST be held and inspected/repaired per the service procedure of this
recall bulletin BEFORE customers take possession of these vehicles.

Dealers are to service all vehicles subject to this recall at no charge to customers, regardless of mileage, age of vehicle, or ownership, from this time
forward.

Customers who have recently purchased vehicles sold from your vehicle inventory, and for which there is no customer information indicated on the
dealer listing, are to be contacted by the dealer. Arrangements are to be made to make the required correction according to the instructions
contained in this bulletin. A copy of the customer letter is shown in this bulletin for your use in contacting customers. Recall follow-up cards should
not be used for this purpose, since the customer may not as yet have received the notification letter.

In summary, whenever a vehicle subject to this recall enters your vehicle inventory, or is in your dealership for service in the future, please take the
steps necessary to be sure the recall correction has been made before selling or releasing the vehicle.

Disclaimer
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 417
Chevrolet Venture V6-3.4L VIN E 2742
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 418
Chevrolet Venture V6-3.4L VIN E 2743

Technical Service Bulletin # 02-07-30-014A Date: 020701

A/T - 4T65-E Spacer Plate/Gasket Service


File In Section: 07 - Transmission/Transaxle

Bulletin No.: 02-07-30-014A

Date: July, 2002

INFORMATION

Subject:
Servicing 4T65-E Transaxle Spacer Plate and Gaskets
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 419
Chevrolet Venture V6-3.4L VIN E 2744

Models:
1997-1999 Buick Riviera
1997-2002 Buick Park Avenue
1998-2002 Buick LeSabre
1999-2002 Buick Regal
2000-2002 Buick Century
2002 Buick Rendezvous
1997-2001 Chevrolet Lumina
1997-2002 Chevrolet Monte Carlo
1999-2002 Chevrolet Venture
2000-2002 Chevrolet Impala
1997-1999 Oldsmobile Eighty Eight
1997-2002 Oldsmobile Silhouette
1998-2002 Oldsmobile Intrigue
2001-2002 Oldsmobile Aurora (3.5L)
1997-2002 Pontiac Bonneville, Grand Prix
1999-2001 Pontiac Trans Sport/Montana
2001-2002 Pontiac Aztek
with 4T65-E Transaxle (RPOs MN3, MN7, M15, M76).

This bulletin is being revised to add models (the Buick Rendezvous, Chevrolet Impala and Pontiac Aztek) Please discard Corporate Bulletin
Number 02-07-30-014 (Section 07-Transmission/Transaxle).

Beginning February 1, 2002, all 4T65-E transaxles will use a bonded spacer plate and gasket assembly (396). The new bonded spacer plate and
gasket assembly may be used in all past model 4T65E transaxles.

Notice:
Do not attempt to remove the gaskets from a bonded spacer plate. Transmission damage could result.

To service the spacer plate for all 4T65-E transaxles produced beginning with Feb. 1, 2002, the vehicle must be serviced with the bonded spacer
plate and gasket assembly.

For those 4T65-E transaxles produced prior to Feb 1, 2002, the spacer plate gaskets (369 & 371) can be serviced. Spacer plate gaskets can be
ordered and serviced individually. However, the spacer plate cannot be ordered/serviced individually. A new bonded spacer plate and gasket
assembly must be installed when a spacer plate is called for during maintenance or service.

DISCLAIMERTechnical Service Bulletin # 02-07-30-014 Date: 020401

A/T - 4T65-E Spacer Plate Service


File In Section: 07 - Transmission/Transaxle

Bulletin No.: 02-07-30-014


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 420
Chevrolet Venture V6-3.4L VIN E 2745

Date: April, 2002

INFORMATION

Subject:
Servicing 4T65-E Transaxle Spacer Plate and Gaskets

Models:
1997-1999 Buick Riviera
1997-2002 Buick Park Avenue
1998-2002 Buick LeSabre
1999-2002 Buick Regal
2000-2002 Buick Century
1997-2001 Chevrolet Lumina
1997-2002 Chevrolet Monte Carlo
1999-2002 Chevrolet Venture
1997-1999 Oldsmobile Eighty Eight
1997-2002 Oldsmobile Silhouette
1998-2002 Oldsmobile Intrigue
2001-2002 Oldsmobile Aurora (3.5L)
1997-2002 Pontiac Bonneville, Grand Prix
1999-2001 Pontiac Trans Sport
1999-2002 Pontiac Montana
with 4T65-E Transaxle (RPOs MN3, MN7, M15, M76).

Beginning February 1, 2002, all 4T65-E transaxles will use a bonded spacer plate and gasket assembly (396). The new bonded spacer plate and
gasket assembly may be used in all past model 4T65E transaxles.

Notice:
Do not attempt to remove the gaskets from a bonded spacer plate. Transmission damage could result.

To service the spacer plate for all 4T65-E transaxles produced beginning with Feb. 1, 2002, the vehicle must be serviced with the bonded spacer
plate and gasket assembly.

For those 4T65-E transaxles produced prior to Feb 1, 2002, the spacer plate gaskets (369 & 371) can be serviced. Spacer plate gaskets can be
ordered and serviced individually. However, the spacer plate cannot be ordered/serviced individually. A new bonded spacer plate and gasket
assembly must be installed when a spacer plate is called for during maintenance or service.

DISCLAIMERTechnical Service Bulletin # 04-07-30-028A Date: 060112

A/T - 4T65-E Fluid Leaks From Reverse Servo Cover


Bulletin No.: 04-07-30-028A

Date: January 12, 2006


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 421
Chevrolet Venture V6-3.4L VIN E 2746

TECHNICAL

Subject:
4T65-E Automatic Transmission Fluid Leak From Reverse Servo Cover (Replace Reverse Servo Cover Seal)

Models:
2005 and Prior Cars and Light Duty Trucks

with Automatic Transmission 4T65-E (RPOs MN3, MN7, M15, M76)

Supercede:

This bulletin is being revised to announce an improved reverse servo cover seal is available from GMSPO and to advise technicians that it is no
longer necessary to replace the reverse servo cover when replacing the seal. The 2005 model year vehicles are also being added. Please discard
Corporate Bulletin Number 04-07-30-028 (Section 07 - Transmission/Transaxle).

Condition

Some customers may comment on a fluid leak under the vehicle. A transmission fluid leak may be noted during the Pre-delivery Inspection (PDI).

Cause

A possible cause of a transmission fluid leak usually only during cold ambient temperatures below -6.7°C (20°F) may be the reverse servo cover
seal. The reverse servo cover seal may shrink in cold ambient temperatures causing a transmission fluid leak.

Correction

Follow the diagnosis and repair procedure below to correct this condition.

1. Diagnose the source of the fluid leak.

2. If the source of the transmission fluid leak is the reverse servo cover, replace the reverse servo cover seal with P/N 24235894. Refer to
Reverse Servo Replacement in the appropriate Service Manual.

3. Clean the area around and below the cover.

4. Inspect the transmission fluid level. Refer to Transmission Fluid Checking Procedure in the appropriate Service Manual.
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 422
Chevrolet Venture V6-3.4L VIN E 2747

Parts Information

Warranty Information

For vehicles repaired under warranty, use the table.

Disclaimer

Technical Service Bulletin # 99-08-44-008 Date: 991001

Cassette Player - Cleaning and Maintenance


File In Section: 08 - Body and Accessories

Bulletin No.: 99-08-44-008

Date: October, 1999

INFORMATION

Subject:
Cassette Player Cleaning and Maintenance

Models:
1998-2000 All Passenger Cars and Trucks with Cassette Tape Players

Radios are being replaced and charged to warranty because the customer has commented on any one or more of the following conditions:

^ The tape plays slow.

^ The tape sounds muffled.

^ The tape sounds garbled.

^ The tape is inoperative.

^ The tape is becoming stuck in the cassette player.

When the radio is returned to the repair center, the cause is found to be a dirty tape head.

When a customer comes in with any of above conditions concerning their cassette player, dealers should perform the normal cassette player
maintenance. Maintenance procedures are in the Owner's Manual and/or the Service Manual. The customer must be charged for this service.
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 423
Chevrolet Venture V6-3.4L VIN E 2748
Technical Service Bulletin # 99-01-38-006A Date: 000501

A/C - Refrigerant Recovery/Recharge Equipment


File In Section: 01 - HVAC

Bulletin No.: 99-01-38-006A

Date: May, 2000

WARRANTY ADMINISTRATION

Subject:
J-43600 ACR 2000 Essential Refrigerant Recovery/Recharge Equipment

Models:
1993-2000 Passenger Cars and Light Duty Trucks with R-134a Refrigerant

This bulletin is being revised to change the effective date and to update the text. Please discard Corporate Bulletin Number 99-01-38-006 (Section
01 - HVAC).

Effective June 1, 2000, the use of J-43600 ACR 2000 will be required on all repairs that require A/C system recovery and are reimbursable by GM.
Additionally, GM highly recommends that J-43600 ACR 2000 be used on all GM cars and trucks for customer paid A/C repairs.

Important:
Also effective June 1, 2000, the "Add" time for all air conditioning recovery is revised to 0.5 hours for front systems and 0.7 hours for front/rear
dual systems (RPO C69 or C34). After June 1, 2000, all air conditioning claims submitted with the 0.9 hours "Add" time will be rejected for
"labor hours excessive".

After the completion of repairs (charging), the ACR 2000 will prompt the user to perform a snapshot of the air conditioning system operating data.
The snapshot includes:

^ Maximum high side pressure.

^ Minimum low side pressure.

^ Duct outlet temperatures (2).

^ Refrigerant purity information.

This information is captured on a paper printout and in a warranty code.

For all GM paid repairs, the paper printout should be attached to the shop copy of the repair order. The warranty code must be submitted in the
warranty claim information in the comments field. The code enables the reporting of valuable information about the repair to GM for product
quality improvement. Claims submitted without this information may be subject to review and subsequent debit.

The required use of J-43600 ACR 2000 raises the question of the acceptable uses for any existing recovery/recycle equipment that GM dealers are
currently using. GM recognizes that many of the previously essential ACR4's are reaching the end of their useful life. There are several alternatives
for existing equipment that may be considered:

^ Use the existing equipment as customer paid recovery only equipment. Example: Collision repair area.

^ Use the existing equipment as a scavenger unit for contaminated A/C systems.

^ Sell the existing units to repair facilities outside the GM dealer network.

^ Discontinue the use of the existing units if the repair/maintenance costs exceed the value of the equipment.

^ Donate the existing equipment to local technical schools.

^ Dedicate the ACR4 to A/C system flushing, using the J-42939 Flush Adapter.

DisclaimerTechnical Service Bulletin # 01-08-97-002 Date: 011101

HomeLink(R) Transmitter - Programming Difficulties


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 424
Chevrolet Venture V6-3.4L VIN E 2749
File In Section: 08 - Body and Accessories

Bulletin No.: 01-08-97-002

Date: November, 2001

INFORMATION

Subject:
Programming the HomeLink(R) Transmitter

Models:
2000-2002 Passenger Cars and Light Duty Trucks with Universal Garage Door Opener (RPO UG1)

If you have customers that are having difficulties programming their HomeLink(R) transmitter, you may suggest the following options:

^ The customer may contact HomeLink(R) directly at 1-800-355-3515 for assistance. Assistance is available in English, French and Spanish
languages.

^ The customer may also be directed to the HomeLink(R) website at www.homelink.com.

The website is user-friendly and actively demonstrates how to program the transmitter. Many newer garage door openers have a "rolling code"
feature and the website does a great job of guiding the owner through the entire programming process.

The HomeLink(R) phone number, website address, and other useful information can also be found in Section 2 of the Owner's Manual under
HomeLink(R) Transmitter.

DisclaimerTechnical Service Bulletin # NHTSA00V228003 Date: 000817

Recall 00V228003: Seat Belt Buckle Defect


Passenger vehicles, light duty trucks, sport utility vehicles, and mini vans equipped with TRW seat belt buckle assemblies. The buckle base of these
seat belt assemblies were not properly heat treated and therefore do not pass the load bearing requirement of Federal Motor Vehicle Safety Standard
No. 209, "Seat Belt Assemblies."

In the event of a vehicle crash, the occupant may not be properly restrained.

Dealers will inspect the vehicle's rear safety belt buckle assembly date codes and, if necessary, will replace any rear safety belt buckle assembly.

Owner notification is expected to begin during August 2000. Owners who take their vehicles to an authorized dealer on an agreed upon service date
and do not receive the free remedy within a reasonable time should contact Buick at 1-800-521-7300; Chevrolet at 1-800-222-1020; GMC at
1-800-462-8782; Oldsmobile at 1-800-442-6537; Pontiac at 1-800-762-2737; or Saturn at 1-800-553-6000. Also contact the National Highway
Traffic Safety Administration's Auto Safety Hotline at 1-888-DASH-2-DOT (1-888-327-4236).
Technical Service Bulletin # 00-09-40-001C Date: 050131

Restraint Systems - Excessive Child Seat Movement


Bulletin No.: 00-09-40-001C

Date: January 31, 2005

TECHNICAL

Subject:
Excessive Lateral Movement of Some Aftermarket Child Seats (Replace Rear Seat Buckle)

Models:
2005 Buick Terraza
1997-2004 Chevrolet Venture
2005 Chevrolet Uplander
1997-2004 Oldsmobile Silhouette
1997-99 Pontiac Trans Sport
1999-2004 Pontiac Montana
2005 Pontiac Montana SV6
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 425
Chevrolet Venture V6-3.4L VIN E 2750
2005 Saturn Relay

Supercede:

This bulletin is being revised to add models and the 2005 model year and remove the Opel model. Please discard Corporate Bulletin Number
00-09-40-001B (Section 09 - Restraints).

Condition

Some customers may comment on excessive lateral movement (side to side) when using certain aftermarket child seats. This condition occurs in
vehicles equipped with second and third row bucket seats (RPO AL4).

Correction

Install a replacement rear seat belt buckle assembly in order to correct this condition.

Important:
This replacement buckle should be used only if the customer is experiencing this condition when using after aftermarket child seat. The
customer should be made aware that the replacement buckle is only available in graphite. You may make the original seat belt buckle assembly
available to the customer for possible reinstallation at a later date. A copy of the procedure below MUST be provided to the customer if the
original seat belt buckle assembly is returned.

For general passenger use, rear seat belt buckle assembly replacements should be made with the original color-coded parts and part numbers as
identified in the Service Parts Catalog.

Removal Procedure

Tools Required

J 29843-9 Door Lock Striker and Seat Belt TORX Wrench (T-50)

Important:
Avoid damaging the bucket seat cushion cover when removing the rear seat belt buckle assembly.

1. Move the seat cushion cover away from the buckle side in order to expose the bolt.

2. Use the J 29843-9 in order to remove the bolt securing the buckle side belt from the seat.

3. Remove the buckle side belt from the seat.

Installation Procedure

1. Use the J 29843-9 to install the bolt securing the buckle side belt to the seat.

Tighten

Tighten the rear seat buckle belt bolt to 53 N.m (39 lb-ft).

2. Reposition the seat cushion cover down over the bolts.

Parts Information

Parts are currently available from GMSPO.

Warranty Information
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 426
Chevrolet Venture V6-3.4L VIN E 2751

For vehicles repaired under warranty, use the table.

Disclaimer
Technical Service Bulletin # 99-06-04-018 Date: 990501

Fuel Pressure - Correct Operating Range


File In Section: 06 - Engine/Propulsion System

Bulletin No.: 99-06-04-018

Date: May, 1999

INFORMATION

Subject:
Correct Fuel Pressure Operating Range

Models:
2000 Buick Century
2000 Chevrolet Impala, Lumina, Malibu, Monte Carlo, Venture
2000 Oldsmobile Alero, Silhouette
2000 Pontiac Grand Am, Grand Prix, Montana
with 3.1 L or 3.4 L V6 Engine (VINs J, E - RPOs LG8, LA1)

All 2000 model year 3.1 L and 3.4 L engines have a revised fuel pressure regulator and Multec II fuel injectors.

The fuel system operating pressure is 358-405 kPa (52-59 psi) on these applications.

Important:

^ This regulator is NOT interchangeable with past model applications. When replacement is necessary for the above listed applications, use
only regulator P/N 17113622.

^ Installing regulators other than the above listed part number in these applications may result in a change in engine performance and/or
driveability concerns.

Refer to the Engine Controls subsection of the Service Manual for complete diagnostic and repair information on fuel system related concerns.

Parts Information

Part Number Description

17113622 Fuel Pressure Regulator

Parts are currently available from GMSPO.Technical Service Bulletin # 04-06-00-047 Date: 040624
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 427
Chevrolet Venture V6-3.4L VIN E 2752
Fuel - Top Tier Detergent Gasoline Information
Bulletin No.: 04-06-00-047

Date: June 24, 2004

ADVANCED SERVICE INFORMATION

Subject:
Top Tier Detergent Gasoline (Deposits, Fuel Economy, No Start, Power, Performance, Stall Concerns)

Models:
2005 and Prior All General Motors Passenger Cars and Trucks (U.S. Only)

A new class of gasoline, called Top Tier Detergent Gasoline, will be appearing at retail stations of some fuel marketers. This gasoline meets
detergency standards developed by four automotive companies. A description of the concept and benefits of Top Tier is provided in the following
question and answer section.

What is Top Tier Detergent Gasoline?

Top Tier Detergent Gasoline is a new class of gasoline with enhanced detergency. It meets new, voluntary deposit control standards developed by
four automotive companies that exceed the detergent requirements imposed by the EPA.

Who developed Top Tier Detergent Gasoline standards?

Top Tier Detergent Gasoline standards were developed by four automotive companies: BMW, General Motors, Honda and Toyota.

Why was Top Tier Detergent Gasoline developed?

Top Tier Detergent Gasoline was developed to increase the level of detergent additive in gasoline. The EPA requires that all gasoline sold in the
U.S. contain a detergent additive. However, the requirement is minimal and in many cases, is not sufficient to keep engines clean. In order to meet
Top Tier Detergent Gasoline standards, a higher level of detergent is needed than what is required by the EPA. Also, Top Tier was developed to
give fuel marketers the opportunity to differentiate their product.

Why did the four automotive companies join together to develop Top Tier?

All four corporations recognized the benefits to both the vehicle and the consumer. Also, joining together emphasized that low detergency is an
issue of concern to several automotive companies.

What are the benefits of Top Tier Detergent Gasoline?

Top Tier Detergent Gasoline will help keep engines cleaner than gasoline containing the "Lowest Additive Concentration" set by the EPA. Clean
engines help provide optimal fuel economy and performance and reduced emissions. Also, use of Top Tier Detergent Gasoline will help reduce
deposit related concerns.

Who should use Top Tier Detergent Gasoline?

All vehicles will benefit from using Top Tier Detergent Gasoline over gasoline containing the "Lowest Additive Concentration" set by the EPA.
Those vehicles that have experienced deposit related concerns may especially benefit from use of Top Tier Detergent Gasoline.

Where can Top Tier Detergent Gasoline be purchased?

The Top Tier program began on May 3, 2004. Some fuel marketers have already joined and are making plans to introduce Top Tier Detergent
Gasoline. This is a voluntary program and not all fuel marketers will offer this product. Once fuel marketers make public announcements, a list of
all fuel marketers meeting Top Tier standards will be made available. For now, look for the "Top Tier" designation at the gas pump.

DisclaimerTechnical Service Bulletin # 99-09-40-004A Date: 050412

Restraints - Child Seat Top Teather Attachment Kits


Bulletin No.: 99-09-40-004a

Date: April 12, 2005


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 428
Chevrolet Venture V6-3.4L VIN E 2753

INFORMATION

Subject:
Top Tether Hardware Package for Child Restraint Seats

Models:
1989-2002 Passenger Cars, Light Duty Trucks and Multi-Purpose Passenger Vehicles

(Except EV1 and Prizm)

Supercede:

This bulletin is being revised to add the 2000-2002 model years. Please discard Corporate Bulletin Number 99-09-40-009 (Section 09 - Restraints).

Important:
GM of Canada and IPC Dealers are not authorized to utilize this service bulletin.

Beginning in August, 1997 General Motors began providing Child Restraint Seat Top Tether Hardware Packages to customers in the United States
who requested them. The Top Tether Hardware Package contains the necessary hardware for anchoring a forward facing child restraint seat top
tether.

One Child Restraint Seat Top Tether Hardware Package will be provided per vehicle to the retail customer at no charge for installation. Charges for
installation of additional Top Tether Hardware Packages per vehicle are the responsibility of the customer.

Most forward facing child restraint seats (CRS) sold in the United States prior to calendar year 1999 were not sold with top tether straps, but have
provisions for them. Top tethers, which are required in Canada, can help to better secure the seat in the vehicle. When a forward facing CRS
including a top tether is used, specially designed components must be used to secure the child seat top tether. These components are included in the
Hardware Package from GMSPO.

Top tethers are not normally required or used with rearward facing infant restraint seats. Rearward facing infant restraint seats should never be
secured in the front seat of an air bag equipped vehicle unless the vehicle is equipped with an air bag de-activation (shut-off) switch and the switch
has been used to turn the air bag off.

Should a retail customer request installation of a Tether Hardware Package at the time of sale or delivery, it is to be installed at no charge to the
owner. The labor to install a Tether Hardware Package prior to delivery of a new vehicle to the customer is considered to be part of the delivery
"get ready process", and as such, is not claimable. Claiming for the cost and applicable handling allowance of the proper Tether Hardware Package
used in the installation is allowed.

If the customer requests installation of a Tether Hardware Package some time after delivery, the package is to be provided free of charge. Hardware
Packages include installation instructions which are easily followed and can be installed by most customers. However, should the customer request
the dealership's assistance to install the Tether Hardware Package, it is to be installed at no charge to the customer and the labor may be claimed.
All claims submitted for installation labor of an approved Tether Hardware Package must be supported by a signed customer work order.
Additional Hardware Packages and installation charges are the responsibility of the customer.

In addition, passenger vehicle deliveries, including vans and sport utilities for daily rental usage, may have one tether hardware package supplied.
Additional packages are the owner's responsibility. Dealers may claim appropriate parts under these circumstances. Sufficient quantities of parts
should be ordered in advance of the arrival of vehicles to avoid delays.

Important:
When installing a Child Restraint Seat Top Tether Hardware Package, follow the installation instructions included in the package. Additional
information about specific mounting locations and installations may be available in the Seat Belt Section (Sections 9, 10-10, 10-11 or 10A) I of
the appropriate Service Manual, or the Restraints section of SI.

Any questions regarding this policy should be directed to your Area Manager, Parts or Service.

Parts Information

For Top Tether Hardware Package part numbers and usage, see Group 14.870 (passenger cars & U-van), or Group 16.710 (Light Duty Truck) of
the appropriate GMSPO Parts Catalog. In addition, they can also be found in Accessories Group 21.042.

Warranty Information

The dealership will be reimbursed for the parts and labor, if applicable, through the submission of a regular warranty claim.

All claims submitted must be supported by a signed customer work order. Purchase and installation of additional Hardware Packages is the
responsibility of the customer.
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 429
Chevrolet Venture V6-3.4L VIN E 2754

For Top Tether Hardware Packages installed in the United States, submit as a normal warranty claim using the labor operations and time
allowances shown.

DisclaimerTechnical Service Bulletin # 01-09-41-008 Date: 010901

Side Impact Air Bag Inflator Module - Replacement Update


File In Section: 09 - Restraints

Bulletin No.: 01-09-41-008

Date: September, 2001

SERVICE MANUAL UPDATE

Subject:
Side Impact Air Bag Inflator Module Replacement

Models:
1997-2001 Buick LeSabre, Park Avenue
1997-99 Buick Riviera
1997-01 Cadillac DeVille, Seville
1997-2001 Chevrolet Venture
1997-99 Oldsmobile Aurora, Eighty Eight
1997-2001 Oldsmobile Silhouette
2001 Oldsmobile Aurora
1997-2001 Pontiac Bonneville
1997-1998 Pontiac Trans Sport
1999-2001 Pontiac Montana
2000-2001 Chevrolet and GMC C/K Utility Models
(Tahoe, Suburban, Yukon, Yukon XL)
2000 Cadillac Escalade

This bulletin is being issued to add the following "Caution" statement to the Side Impact Air Bag Inflator Module Replacement procedure in the
SIR sub-section of the Service Manual. Please add this information to your Service Manual.

This information has been updated within SI2000. If you are using a paper version of this Service Manual, please mark a reference to this bulletin
on the affected page.

When replacing a Side Impact Air Bag Inflator Module on the above described vehicles, always refer to the following caution.

Caution:
Following the deployment of a side impact air bag, inspect the following parts for damage. Replace these parts if necessary:

^ The seat cushion frame


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 430
Chevrolet Venture V6-3.4L VIN E 2755

^ The seat recliner, if equipped

^ The seat adjuster

^ The seat back frame

Failure to do so may cause future personal injury

DISCLAIMERTechnical Service Bulletin # 02-01-39-004B Date: 051116

A/C - New PAG Oil


Bulletin No.: 02-01-39-004B

Date: November 16, 2005

INFORMATION

Subject:
New PAG Oil Released

Models:
2006 and Prior GM Passenger Cars and Trucks (Including Saturn)
2003-2006 HUMMER H2
2006 HUMMER H3
2005-2006 Saab 9-7X

Built With R-134a Refrigeration System

All Air Conditioning Compressor Types (Excluding R4 and A6 Type Compressors)

Supercede:

This bulletin is being revised to change the PAG oil part number used for R4 and A6 compressors with R-134a refrigerant systems. Please discard
Corporate Bulletin Number 02-01-39-004A (Section 01 - HVAC).

All General Motors vehicles built with R-134a refrigerant systems shall now be serviced with GM Universal PAG Oil (excluding vehicles equipped
with an R4 or A6 compressor).

R4 and A6 compressors with R-134a refrigerant systems shall use PAG OIL, GM P/N 12356151 (A/C Delco part number 15-118) (in Canada, use
P/N 10953486).

Important:
The PAG oil referenced in this bulletin is formulated with specific additive packages that meet General Motors specifications and use of another
oil may void the A/C systems warranty.

Use this new PAG oil when servicing the A/C system on the vehicles listed above. Oil packaged in an 8 oz tube should be installed using A/C Oil
Injector, J 45037. Refer to the HVAC Section of Service Information for detailed information on Oil Balancing and Capacities.
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 431
Chevrolet Venture V6-3.4L VIN E 2756

DisclaimerTechnical Service Bulletin # 01-08-46-006A Date: 011201

Onstar(R) - Antenna Coupling Revised Procedures


File In Section: 08 - Body and Accessories

Bulletin No.: 01-08-46-006A

Date: December, 2001

SERVICE MANUAL UPDATE

Subject:
Revised OnStar(R) Antenna Coupling Replacement Procedures

Models:
2000-2002 Passenger Cars and Trucks with Glass Mounted Antenna

This bulletin is being revised to add the 2002 model year and revise the service procedures. Please discard Corporate Bulletin Number
01-08-46-006 (Section 08 - Body and Accessories).

This bulletin is being issued to revise the OnStar(R) inner and outer antenna coupling replacement procedures in the Cellular Communication
sub-section of the Body and Accessories section in the appropriate Service Manual. Please use the following to replace the existing information in
the Service Manual.

This information has been updated within SI2000. If you are using a paper version of this Service Manual, please mark a reference to this bulletin
on the affected page in the Cellular Communication sub-section of the Service Manual.

Coupling Replacement - Antenna Inner

Removal Procedure

Important:
Use the described adhesion promoter to assure adequate bonding of the coupling to the glass. To obtain maximum adhesion between the new
mobile antenna couplings and the glass surface, the couplings and the glass must be kept dry and above 15°C (60°F) during the installation and
for 6-8 hours immediately following the installation. Otherwise the new couplings may come off. Also, disregard the drying or curing time
information listed in the instructions included in the replacement antenna coupling kits. In the near future, those instructions will be updated
with the drying or curing times listed in this bulletin.

^ Do not attempt to reinstall the original cellular couplings using any type of glue, adhesive tapes, etc. Doing so may eliminate the cellular signal
transfer through the glass and reduce the maximum performance of the system, including the air bag deployment notification.

1. Disconnect the coaxial cable from the inner coupling of the mobile communication antenna.

Notice:
If you use a razor blade or other sharp tool in order to remove the adhesives or foreign objects from the inside of the rear window, use the blade
carefully. Damage to the grid lines may result.
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 432
Chevrolet Venture V6-3.4L VIN E 2757

Use a small, wide-bladed plastic tool to cut the double back tape material while lifting up on the inner antenna coupling.

Installation Procedure

1. Clean the inside of the glass with an alcohol wipe.

2. Dry the glass thoroughly using a lint free cloth.

Important:
The glass adhesion promoter described in the next step must be used to ensure a bonding of the coupling to the glass surface. Failure to use the
described adhesion promoter may result in the coupling coming off the glass.

3. Apply Glass Adhesion Promoter, P/N 12378555 (in Canada, use P/N 88901239), to the glass in the area where you will install the antenna
coupling. Follow the Glass Adhesion Promoter instructions on the product label.

Important:

^ On rear backglass applications the RF connections for the inner antenna coupling should run parallel to the defogger gridline.

^ Align the inner and the outer antenna couplings.

^ Do not touch the adhesive backing on the antenna coupling.

4. Remove the protective film from the adhesive backing on the inner antenna coupling.

5. Align the inner antenna coupling to the existing exterior coupling.

6. Press firmly on all 4 corners and on the center of the antenna inner coupling (2) in order to ensure proper adhesion to the glass (4).

Hold pressure on the inner coupling (2) for 10 to 30 seconds.

7. Ensure that no gaps occur between the couplings (5, 2) and the glass (4).

8. Connect the coaxial cable to the inner coupling (2).

9. Keep the vehicle dry. Allow 6 to 8 hours, at 15°C (60° F), for the adhesive to cure after installation.

Coupling Replacement - Antenna Outer


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 433
Chevrolet Venture V6-3.4L VIN E 2758

Removal Procedure

Important:

Use the described adhesion promoter to assure adequate bonding of the coupling to the glass.

To obtain maximum adhesion between the new mobile antenna couplings and the glass surface, the couplings and the glass must be kept dry
and above 15°C (60° F) during the installation and for the 6-8 hours immediately following the installation. Otherwise the new couplings may
come off. Also, disregard the drying or curing time information listed in the instructions included in the replacement antenna coupling kits. In
the near future, those instructions will be updated with the drying or curing times listed in this bulletin.

^ Do not attempt to reinstall the original cellular couplings using any type of glue, adhesive tapes, etc. Doing so may eliminate the cellular
signal transfer through the glass and reduce the maximum performance of the system, including the air bag deployment notification.

1. Install the inner coupling first if both the inner and the outer coupling are to be replaced.

Refer to Coupling Replacement - Antenna Inner.

Notice:
If you use a razor blade or other sharp tool in order to remove the adhesives or foreign objects from the inside of the rear window, use the blade
carefully. Damage to the grid lines may result.

2. Use a small, wide-bladed plastic tool to cut the double back tape material while lifting up on the outer antenna coupling.

Installation Procedure

1. Clean the glass with an alcohol wipe.

2. Dry the glass thoroughly using a lint free cloth.

Important:
The glass adhesion promoter described in the next step must be used to ensure a bonding of the coupling to the glass surface. Failure to use the
described adhesion promoter may result in the coupling coming off the glass.

3. Apply Glass Adhesion Promoter, P/N 12378555 (in Canada, use P/N 88901239), to the glass in the area where you will install the antenna
coupling. Follow the Glass Adhesion Promoter instructions on the product label.

Important:
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 434
Chevrolet Venture V6-3.4L VIN E 2759

^ Align the outer antenna coupling with the inner coupling.

^ Do not touch the adhesive backing on the antenna coupling.

4. Remove the protective film from the adhesive backing on the outer antenna coupling.

5. Align the outer antenna coupling to the inner antenna coupling.

6. Press firmly on all 4 corners and on the center of the outer antenna coupling (5) in order to ensure proper adhesion to the glass (4).

Hold pressure on the outer coupling (5) for 10 to 30 seconds.

7. Ensure that no gaps occur between the couplings (5, 2) and the glass (4).

8. Keep the vehicle dry. Allow 6 to 8 hours, at 15°C (60°F), for the adhesive to cure after installation.

DisclaimerTechnical Service Bulletin # NHTSA01V264000 Date: 010820

Recall 01V264000: Sliding Door Defect


Vehicle Description: 1997-2001 Chevrolet Venture, Pontiac Montana/Transport, and Oldsmobile Silhouette mini vans equipped with passenger
side power sliding doors, that were serviced in Campaign 01013 (01V-067) from April to August 2001. Also 2001 Chevrolet Venture, Pontiac
Montana, and Oldsmobile Silhouette mini vans equipped with passenger side power sliding doors assembled in January through April 2001. These
vehicles have inadequate front sonic welds. If a front sonic weld fails, the actuator can jam in the unlatched position and, when the sliding door
closes, it will not be latched.

If this happens, the power sliding door can open while the vehicle is in motion, particularly when the vehicle ascends a hill, makes a turn, or travels
over a rough road surface. An unrestrained occupant could fall out of the van and be injured.

Dealers will inspect the actuators for certain date codes and, if necessary, replace the actuators. GM has not yet provided an owner notification
schedule for this campaign. Owners who take their vehicles to an authorized dealer on an agreed upon service date and do not receive the free
remedy within a reasonable time should contact Chevrolet at 1-800-222-1020, Pontiac at 1-800-762-2737, or Oldsmobile at 1-800-442-6537. Also
contact the National Highway Traffic Safety Administration's Auto Safety Hotline at 1-888-DASH-2-DOT (1-888-327-4236). Technical Service
Bulletin # 01059 Date: 011001

Recall - Defective Power Sliding Door


File In Section: Product Recalls

Bulletin No.: 01059

Date: October 2001

PRODUCT SAFETY RECALL

SUBJECT:
01059 - POWER SLIDING DOOR
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 435
Chevrolet Venture V6-3.4L VIN E 2760

MODELS:
1997-2001 CHEVROLET VENTURE, PONTIAC MONTANA/TRANS SPORT, AND OLDSMOBILE SILHOUETTE "U" VAN WITH POWER
SLIDING DOORS (RPO E58 / E59)

Due to parts availability, ordering restrictions are being imposed to ensure an equitable distribution of part inventory. Refer to the Parts Information
section for details.

CONDITION

General Motors has decided that a defect which relates to motor vehicle safety exists in certain 1997-2001 Chevrolet Venture, Pontiac
Montana/Trans Sport, and Oldsmobile Silhouette model vehicles equipped with driver and/or passenger side power sliding doors. Some of the door
unlatch actuators in vehicles assembled in January-April 2001 and in vehicles that were serviced in Recall 01013 from April-August 2001 have
inadequate front sonic welds. If a front sonic weld fails, the actuator can jam in the unlatched position and, when the sliding door closes, it will not
be latched. If this happens, the power sliding door can open while the vehicle is in motion, particularly when the vehicle ascends a hill, makes a
turn, or travels over a rough road surface. An unrestrained occupant could fall out of the van and could be injured.

CORRECTION

Dealers are to inspect and if required, install a new power sliding door unlatch actuator assembly.

VEHICLES INVOLVED

Involved are certain 1997-2001 Chevrolet, Pontiac, and Oldsmobile "U" Van model vehicles equipped with RPO E58 or E59, power sliding doors,
and built within these VIN breakpoints shown.

The table shown contains VIN breakpoints for vehicles that were serviced under Recall 01013 from April-August 2001, and may have had suspect
actuators installed.

The table shown contains VIN breakpoints for vehicles specific to this Recall 01059, and were assembled in January-April 2001 and may have had
suspect actuators installed.

IMPORTANT:
Dealers should confirm vehicle eligibility through GMVIS (GM Vehicle Inquiry System) or GM Access Screen (Canada only) or DCS Screen
445 (IPC only) before beginning recall repairs. [Not all vehicles within the above breakpoints may be involved.]

Involved vehicles have been identified by Vehicle Identification Number. Computer listings containing the complete Vehicle Identification
Number, customer name and address data have been prepared, and are being furnished to involved dealers with the recall bulletin. The customer
name and address data furnished will enable dealers to follow up with customers involved in this recall. Any dealer not receiving a computer listing
with the recall bulletin has no involved vehicles currently assigned.

These dealer listings may contain customer names and addresses obtained from Motor Vehicle Registration Records. The use of such motor vehicle
registration data for any other purpose is a violation of law in several states/provinces/countries. Accordingly, you are urged to limit the use of this
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 436
Chevrolet Venture V6-3.4L VIN E 2761
listing to the follow-up necessary to complete this recall.

PARTS INFORMATION

Important:
An initial supply of RH actuator kits required to complete this recall will be pre-shipped the week of November 5, 2001 to dealers with claims
paid through April 30, 2001 for recall 01013. Pre-shipped parts will be charged to dealer's open parts account. Due to limited part supply, prior
to pre-ship, parts will be placed on an order writing control. Any orders prior to Nov. 5, 2001 will be canceled. After completion of the pre-ship,
a quantity limiter will be added to the part that will limit the pieces per order line. The reason this is being done is to facilitate an equitable
distribution of part inventory.

Additional parts, if required, are to be obtained from General Motors Service Parts Operations (GMSPO). Please refer to your "involved vehicles
listing" before ordering parts. Normal orders should be placed on a DRO = Daily Replenishment Order. In an emergency situation, parts should be
ordered on a CSO = Customer Special Order.

RECALL IDENTIFICATION LABEL - For US and IPC

Place a Recall Identification Label on each vehicle corrected in accordance with the instructions outlined in this Product Recall Bulletin. Each label
provides a space to include the recall number and the five (5) digit dealer code of the dealer performing the recall service. This information may be
inserted with a typewriter or a ball point pen.

Put the Recall Identification Label on a clean and dry surface of the radiator core support in an area that will be visible to people servicing the
vehicle. When installing the Recall Identification Label, be sure to pull the tab to allow adhesion of the clear protective covering. Additional Recall
Identification Labels for US dealers can be obtained from Dealer Support Materials by calling 1-866-700-0001 (Monday-Friday, 8:00 a.m. to 5:00
p.m. EST). Ask for Item Number 5-1015 when ordering.

Additional Recall Identification Labels for IPC dealers can be obtained from your Regional Marketing Office.

RECALL IDENTIFICATION LABEL - For CANADA

Place a Recall Identification Label on each vehicle corrected in accordance with the instructions outlined in this Product Recall Bulletin. Each label
provides a space to include the recall number and the five (5) digit dealer code of the dealer performing the recall service. This information may be
inserted with a typewriter or a ball point pen.

Put the Recall Identification Label on a clean and dry surface of the radiator core support in an area that will be visible to people servicing the
vehicle. Additional Recall Identification Labels for Canadian dealers can be obtained from DGN by calling 1-800-668-5539 (Monday - Friday,
8:00 a.m. to 5:00 p.m. EST). Ask for Item Number GMP 91 when ordering.

COURTESY TRANSPORTATION - U.S. AND CANADA ONLY


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 437
Chevrolet Venture V6-3.4L VIN E 2762

The availability of a loaner/rental vehicle to customers whose vehicles are involved in this recall is of the utmost importance in maintaining
customer satisfaction. If requested, please ensure that these customers have the opportunity to use a loaner/rental vehicle for one day at no charge
while their vehicle is being serviced. One day is defined as a 24-hour period and the maximum allowance for the loaner/rental vehicle is $30.00
(U.S.), $40.00 (Canada). Please make sure that required parts are available at your dealership prior to scheduling service appointments for these
customers.

CLAIM INFORMATION

Submit a Product Recall Claim with the information as shown.

Refer to the General Motors WINS Claims Processing Manual for details on Product Recall Claim Submission.

CUSTOMER NOTIFICATION - For US and CANADA

Customers will be notified of this recall on their vehicles by General Motors (see copy of customer letter shown in this bulletin.

CUSTOMER NOTIFICATION - For IPC

Letters will be sent to known owners of record located within areas covered by the US National Traffic and Motor Vehicle Safety Act. For owners
outside these areas, dealers should notify customers using the suggested dealer letter shown.

DEALER RECALL RESPONSIBILITY - For US and IPC (US States, Territories, and Possessions)

The US National Traffic and Motor Vehicle Safety Act provides that each vehicle that is subject to a recall of this type must be adequately repaired
within a reasonable time after the customer has tendered it for repair. A failure to repair within sixty days after tender of a vehicle is prima facie
evidence of failure to repair within a reasonable time. If the condition is not adequately repaired within a reasonable time, the customer may be
entitled to an identical or reasonably equivalent vehicle at no charge or to a refund of the purchase price less a reasonable allowance for
depreciation. To avoid having to provide these burdensome remedies, every effort must be made to promptly schedule an appointment with each
customer and to repair their vehicle as soon as possible. In the recall notification letters, customers are told how to contact the US National
Highway Traffic Safety Administration if the recall is not completed within a reasonable time.

DEALER RECALL RESPONSIBILITY - ALL

All unsold new vehicles in dealers' possession and subject to this recall must be held and inspected/repaired per the service procedure of this recall
bulletin before customers take possession of these vehicles.

Dealers are to service all vehicles subject to this recall at no charge to customers, regardless of mileage, age of vehicle, or ownership, from this time
forward.

Customers who have recently purchased vehicles sold from your vehicle inventory, and for which there is no customer information indicated on the
dealer listing, are to be contacted by the dealer. Arrangements are to be made to make the required correction according to the instructions
contained in this bulletin. This could be done by mailing to such customers, a copy of the customer letter shown in this bulletin. Recall follow-up
cards should not be used for this purpose, since the customer may not as yet have received the notification letter.
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 438
Chevrolet Venture V6-3.4L VIN E 2763

In summary, whenever a vehicle subject to this recall enters your vehicle inventory, or is in your dealership for service in the future, you must take
the steps necessary to be sure the recall correction has been made before selling or releasing the vehicle.

DISCLAIMER
Important Information
IMPORTANT:
The service procedure contained in this recall is different from the service procedure found in the appropriate service manual. As a result, the
labor time allowance has been revised to correspond with this new service procedure. In the near future the service manual and labor time guide
will be updated with this new information.

Inspection Process
(Right side shown, Left side similar)

1. Remove the garnish at the top of the door trim panel.

2. Remove the inside door handle using J-42506.

3. Remove the door trim panel.

4. Partially remove the water deflector.

5. Remove the bolts (three) from the lock plate.

6. With light pressure push outward on the latch plate and look through the hole in the inner panel. See arrow in figure 1.

7. Inspect the actuator date code located directly below the part number on the side of the actuator, to determine if actuator replacement is
needed. The date code consists of three parts:

^ Juan date: example: 118 = the 118th day of the calendar year (i.e. April 28, 2001)

^ Calendar Year: example: 01 = 2001, 00 = 2000

^ Production Shift example: A = 1st shift: B = 2nd shift

If the date code is 118-01-A or greater, replacement is not required. If the date code is 117-01-A or less (including any date code with 00" for
calendar year), replace the actuator. If replacement is required, follow the Replacement Procedure.

8. If replacement is not required, torque the bolts to the lock plate following the torque sequence to 10 Nm (89 lb. in.). See step 13 and figure 6
of Replacement Procedure.

9. Reinstall the water deflector.

10. Remove and replace the thirteen trim panel fasteners.


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 439
Chevrolet Venture V6-3.4L VIN E 2764

11. Reinstall the door trim panel.

12. Reinstall the garnish molding at the top of the door trim panel.

13. Install the GM Recall Identification Label.

Replacement Procedure
(Right side shown, Left side similar)

1 Remove the electrical connectors from the actuators. Refer to (1) in figure 2.

2. Remove the lock rod from the latch plate assembly. Refer to (2) in figure 2.

3. Disconnect the lock rod from the center of the door so the rod can be moved to the side. Refer to (2) in figure 2.

4. Remove the bolts (four) from the latch.

5. Rotate the latch plate counter clockwise slightly and rearward to remove the latch plate.

6. Remove the outside handle cable from the latch plate.

7. Drill the rivets from the actuator. Refer to arrows in figure 3.

8 Replace the rivets in the same direction as they were removed. See figure 4.

9. Replace the lock rod retainer.

10. Install the outside cable to the latch plate.


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 440
Chevrolet Venture V6-3.4L VIN E 2765

11. Reinstall the latch plate and hand tighten the bolts.

12. Torque the bolts to the latch following the torque sequence to 10 Nm (89 lb. in.). See figure 5.

13. Torque the bolts to the lock plate following the torque sequence to 10 Nm (89 lb. in.). See figure 6.

14. Reinstall the lock rod to the lock plate and the lock rod retainer.

15. Reinstall the electrical connectors.

16. Important: Before the door trim is reinstalled close the latch at the rear of the door with a screwdriver. Look through the small oval hole just
above the door handle and rotate the door handle rearward. Just before the lever gets to the stop (see arrow in figure 7) the latch should open.
If the latch does not open, a slight bend to shorten the rod (see arrows in figure 8) will be necessary.

17. Reinstall the water deflector.

18. Remove and replace the thirteen trim panel fasteners.

19. Reinstall the door trim panel.

20. Reinstall the garnish molding at the top of the door trim panel.
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 441
Chevrolet Venture V6-3.4L VIN E 2766

21. Install the GM Recall Identification Label.


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 442
Chevrolet Venture V6-3.4L VIN E 2767
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 443
Chevrolet Venture V6-3.4L VIN E 2768
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 444
Chevrolet Venture V6-3.4L VIN E 2769
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 445
Chevrolet Venture V6-3.4L VIN E 2770
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 446
Chevrolet Venture V6-3.4L VIN E 2771
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 447
Chevrolet Venture V6-3.4L VIN E 2772

Technical Service Bulletin # 04-06-04-054A Date: 070111

Engine Controls - Aftermarket Accessory Usage


Bulletin No.: 04-06-04-054A

Date: January 11, 2007

INFORMATION

Subject:
Non-GM Parts and Accessories (Aftermarket)

Models:
2007 and Prior Passenger Cars and Trucks (Including Saturn)
2007 and Prior HUMMER H2, H3
2005-2007 Saab 9-7X

Supercede:

This bulletin is being updated to add models and model years. Please discard Corporate Bulletin Number 04-06-04-054 (Section 06 - Engine).

The recent rise and expansion of companies selling non-GM parts and accessories has made it necessary to issue this reminder to dealers regarding
GM's policy on the use and installation of these components.

When a dealer is performing a repair under the New Vehicle Limited Warranty, they are required to use only genuine GM or GM-approved parts
and accessories. This applies to all warranty repairs, special policy repairs or any repairs paid for by GM. Parts and accessories advertised as being
"the same" as parts manufactured by GM, but not sold through GM, do not qualify for use in warranty repairs, special policy repairs or any repairs
paid for by GM.

During a warranty repair, if a GM original equipment part is not available through GMSPO, ACDelco(R) distributors, other GM dealers or
approved sources, the dealer is to obtain comparable, non-GM parts and clearly indicate, in detail, on the repair order the circumstances
surrounding why non-GM parts were used. The dealer must give customers written notice, prior to the sale or service, that such parts or accessories
are not marketed or warranted by General Motors.

It should also be noted that dealers modifying new vehicles and installing equipment, parts and accessories obtained from sources not authorized by
GM are responsible for complying with the National Traffic and Motor Vehicle Safety Act. Certain non-approved parts or assemblies, installed by
the dealer or its agent not authorized by GM, may result in a change to the vehicle's design characteristics and may affect the vehicle's ability to
conform to federal law. Dealers must fully understand that non-GM approved parts may not have been validated, tested or certified for use. This
puts the dealer at risk for potential liability in the event of a part or vehicle failure. If a GM part failure occurs as the result of the installation or use
on a non-GM approved part, the warranty will not be honored.

A good example of non-authorized modification of vehicles is the result of an ever increasing supply of after market devices available to the
customer, which claim to increase the horsepower and torque of the Duramax(TM) Diesel Engines. These include the addition of, but are not
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 448
Chevrolet Venture V6-3.4L VIN E 2773
limited to one or more of the following modifications:

Propane injection

Nitrous oxide injection

Additional modules (black boxes) that connect to the vehicle wiring systems

Revised engine calibrations downloaded for the engine control module

Calibration modules which connect to the vehicle diagnostic connector Modification to the engine turbocharger waste gate

Although the installation of these devices, or modification of vehicle components, can increase engine horsepower and torque, they may also
negatively affect the engine emissions, reliability and/or durability. In addition, other powertrain components, such as transmissions, universal
joints, drive shafts, and front/rear axle components, can be stressed beyond design safety limits by the installation of these devices.

General Motors does not support or endorse the use of devices or modifications that, when installed, increase the engine horsepower and torque.

These same policies apply as they relate to the use of non-GM accessories. Damage or failure from the use or installation of a non-GM accessory
will not be covered under warranty. Failure resulting from the alteration or modification of the vehicle, including the cutting, welding or
disconnecting of the vehicle's original equipment parts and components will void the warranty.

Additionally, dealers will NOT be reimbursed or compensated by GM in the event of any legal inquiry at either the local, state or federal level that
results from the alteration or modification of a vehicle using non-GM approved parts or accessories.

Dealers should be especially cautious of accessory companies that claim the installation of their product will not void the factory warranty. Many
times these companies have even given direction on how to quickly disassemble the accessory in an attempt to preclude the manufacturer from
finding out that is has been installed.

Any suspect repairs should be reviewed by the Area Service Manager (District Service Manager in Canada) for appropriate repair direction. If it is
decided that a goodwill repair is to be made on the vehicle, even with the installation of such non-GM approved components, the customer is to be
made aware of General Motors position on this issue and is to sign the appropriate goodwill documentation required by General Motors.

It is imperative for dealers to understand that by installing such devices, they are jeopardizing not only the warranty coverage, but also the
performance and reliability of the customer's vehicle.

Disclaimer
Technical Service Bulletin # 02-08-98-001C Date: 061009

Body - Metal Panel Adhesive Bonding Information


Bulletin No.: 02-08-98-001C

Date: October 09, 2006

INFORMATION

Subject:
Metal Panel Bonding

Models:
2007 and Prior GM Passenger Cars and Trucks (Including Saturn)
2003-2007 HUMMER H2
2006-2007 HUMMER H3
2005-2007 Saab 9-7X
2007 and Prior Isuzu Medium Duty Commercial Trucks

Attention:
This bulletin applies to all models that have published panel bonding procedures in SI.

Supercede:

This bulletin is being revised to update the applicable models and add information. Please discard Corporate Bulletin Number 02-08-98-001B
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 449
Chevrolet Venture V6-3.4L VIN E 2774
(Section 08 - Body and Accessories).

This bulletin is intended to provide general information for adhesive bonding of Non-Structural exterior panels as an alternative to MIG welding.
Panel bonding may be seen as an alternative to MIG welding to provide full panel replacement in regards to collision repair procedures. The
benefits of panel bonding include the following:

No heat or burn damage when additional welding is not required

Corrosion protection

Can act as a sealant

Improved process for complicated shapes (wheelhouse area)

The General Motors specification for metal bonding adhesives is GM 6449G and provides test and standards information to adhesive manufacturers
and suppliers. The scope of this specification is intended to provide the performance guidelines of structural adhesive systems used to repair
(metallic) automotive bodies in the aftermarket. These types of adhesives are intended for use when bonding Non-Structural replacement body
panels as an option to welding as the attachment means. Supplier guidelines outline the use of room temperature cure acrylic adhesives that contain
glass bead technology.

Bonding procedures in general are applicable only to a factory seams type approach. Sectioning or partial paneling of full panels is not supported
by General Motors unless specifically documented in a Service Bulletin or Manual.

Applicable components for this technology are NON-STRUCTURAL EXTERIOR PANELS ONLY, including door skins, tail panels, roof outer
panels and quarter panels. While this bonding process has gained popularity, General Motors only supports this process for vehicles which it has
published written repair procedures that are found in a Service Manual or Bulletin.

Adhesives currently meeting the performance requirements include General Motors materials, Lord Adhesives, Ashland Plio Grip, and products
manufactured by 3M Corporation. At this time, ONLY the adhesive products shown meet this guideline.

Service information is also available on the web.

(www.acdelcotechconnect.com) - This website includes service repair information for the total vehicle and is a subscription based site.

(www.techinfo.gmgoodwrench.com) - This website includes select collision repair information only and is downloadable and free to the user.
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 450
Chevrolet Venture V6-3.4L VIN E 2775

DisclaimerTechnical Service Bulletin # 06-06-04-037 Date: 060804

Engine Controls - MIL Function During I/M Testing


Bulletin No.: 06-06-04-037

Date: August 04, 2006

INFORMATION

Subject:
Normal Characteristics of Malfunction Indicator Lamp (MIL) During On-Board Diagnostic (OBD) Inspection/Maintenance (I/M) Testing

Models:
2007 and Prior Passenger Cars and Trucks (Including Saturn)
2007 and Prior HUMMER H2, H3
2007 and Prior Saab 9-7X

The purpose of this bulletin is to inform dealers and OBD inspection/maintenance testing facilities of normal characteristics of the malfunction
indicator lamp (MIL) and the engine or powertrain control module (ECM or PCM).

Some customers may comment on having been rejected or having failed an OBD emission inspection. In some cases, these vehicles do not need
repair and may have been rejected or may have failed the OBD emission inspection due to a lack of understanding with regard to the normal
characteristics of the MIL and ECM/PCM.

Following an engine run period, the MIL may not illuminate on an ignition OFF to ignition ON transition unless a 30 second delay is observed
between key OFF and key ON. The delay is necessary on some control modules to allow the control module, either ECM or PCM, to power down.
Most vehicles may require less time to achieve power down, but a 30 second delay will satisfy all known applications. This is normal operation for
all GM control modules.

Some OBD I/M emissions test centers may not wait 30 seconds after a vehicle is turned off before proceeding with the MIL bulb check, which
could result in a vehicle rejection or test failure.

To confirm proper MIL operation, wait 30 seconds after the ignition is turned OFF before proceeding with any key ON bulb check.

DisclaimerTechnical Service Bulletin # 00-06-04-033B Date: 061010

Emissions - OBDII I/M Readiness Testing


Bulletin No.: 00-06-04-033B

Date: October 10, 2006

INFORMATION

Subject:
I/M Readiness as Part of Emission Inspection and Maintenance Program for OBD II Vehicles

Models:
1996-2007 GM Passenger Cars and Light Duty Trucks (Including Saturn)
2003-2007 HUMMER H2
2006-2007 HUMMER H3
2005-2007 Saab 9-7X

with OBD II Emissions Systems


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 451
Chevrolet Venture V6-3.4L VIN E 2776

Attention:
"GM of Canada" and "IPC" Dealers are not authorized to utilize this Service Bulletin.

Supercede:

This bulletin is being revised to add models, model years and additional information on emission testing. Please discard Corporate Bulletin Number
00-06-04-033A (Section 06 - Engine-Engine Controls).

Inspection Maintenance (I/M) Program

Several states require that vehicles pass OBD system I/M emissions inspection. These inspections may apply to any 1996 and newer model year
OBD II equipped passenger cars and light duty trucks.

As part of an OBD I/M emission inspection, the vehicles I/M readiness status is checked to ensure that the vehicle's OBD system has properly
evaluated the emissions systems of the vehicle for proper operation. To ensure vehicles are capable of passing this portion of the inspection,
technicians can review the I/M readiness test status using the I/M System Status display on the Tech(R)2. This display provides test data that will
verify whether the vehicle's OBD systems have run. States performing inspections on an advisory basis will not reject vehicles for not being
I/M-ready.

Conditions for Updating the I/M System Status

Each OBD II system requires at least one diagnostic test. A system monitor is complete when all of the DTCs that report to the system monitor have
run and passed or failed. The results of a failed test are reported by a diagnostic trouble code (DTC).

Once all of the tests are complete, the I/M System Status display indicates YES in the "Completed" column. For example, when the HO2S Heater
Test indicates YES, all oxygen sensor heaters have been diagnosed.

When any required test for a specified system has not run, the "Completed" column under I/M System Status displays NO. The following is a list of
conditions that would set the I/M System Status indicator to NO:

The vehicle is new from the factory and has not yet been driven through the necessary drive conditions to complete the tests.

The battery has been disconnected or discharged below operating voltage.

The control module power or ground has been interrupted.

The control module has been reprogrammed.

The control module DTCs have been cleared as part of a service procedure.

Monitored Emission Control Systems

The OBD II System monitors all emission control systems that are on-board. Not all vehicles have a full complement of emission control systems.
For example, a vehicle may not be equipped with AIR or EGR.

The following is a complete list of the vehicle's systems that may require monitoring by the OBD system:

Air conditioning system

Catalytic converter efficiency

Comprehensive component monitoring (emission-related inputs and outputs)

Evaporative Emissions (EVAP) system

Exhaust Gas Recirculation (EGR) system

Fuel delivery system

Heated catalyst monitoring

Misfire monitoring

Oxygen sensor system (02S or HO2S)

Oxygen sensor heater system (HO2S heater)

Secondary Air Injection (AIR) system


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 452
Chevrolet Venture V6-3.4L VIN E 2777

If a specific vehicle is not required to monitor one or more of the above listed systems, the Tech(R)2 display will read "not supported." Any
non-supported system will not be considered when determining the readiness of the overall system.

For the specific DTCs related to each system, refer to SI (Service Information) for further diagnostic information on conditions for running the
DTC or refer to the publication information mentioned in this bulletin to order the Inspection Maintenance Emissions Diagnostics Manual and
follow the I/M Readiness Testing System DTC Tables. Systems such as fuel delivery, misfire, and comprehensive components may not be listed in
a system status list. These tests run continuously on some vehicles and may not require an indicator.

Diagnostic Aids

The I/M System Status display indicates when the control module has completed the required tests. This does not necessarily mean that the test has
passed, only that a decision was made. If the diagnostic fails, a DTC will indicate the failure. If a failure indication is present, it may prevent other
required tests from running. For example, a DTC for the control circuit of the relay controlling an AIR pump may not be listed in the Inspection
Maintenance System DTC Table because it is a continuous test. If this DTC is set, the Active Tests for the AIR system may not run and AIR system
readiness could display "NO."

The I/M System Status information may be useful for a technician to determine if diagnostics have run when verifying repairs.

Publications

General Motors Service and Parts Operations has published a supplement titled "Inspection Maintenance Emissions Diagnostics Manual" (Item #
SD-MA-IM240).

This publication includes the content of the General Motors Green Books (GMPT/97-IM240 and GMPT/95-IM240). Content covers enhanced I/M
program, including the procedures for setting OBD II monitors. To order this manual, contact ACDelco(R) at 1-800-825-5886.

Training

General Motors Service Technical College (STC) offers two courses for technicians to address service issues related to this type of testing.

16042.10B, H Enhanced Vehicle Emissions, Testing and Diagnostics

16044.14W3 GM Powertrain Performance

For more information about service technical training, visit the GM Training website.

Having competent, trained technicians will give your Service Department a competitive edge by offering your customers a dependable repair
facility which can fix vehicles right the first time.

DisclaimerTechnical Service Bulletin # 01-08-45-005E Date: 060829

Electrical - Hard or No Start/Warning Lamps ON/DTC's Set


Bulletin No.: 01-08-45-005E

Date: August 29, 2006

TECHNICAL

Subject:
Hard/No Start, Fuel Gauge Inoperative/Fluctuates, SES/Check Engine Light On, ABS Warning Light On, TCS Warning Light On, TCS Activation,
Service Traction System Message Displayed, All-Wheel Drive Disable Message Displayed, DTCs Set (Repair Connector)

Models:
2002-2006 Buick Rendezvous
2005-2007 Buick Terraza
2000-2005 Chevrolet Venture
2005-2007 Chevrolet Uplander
2000-2004 Oldsmobile Silhouette
2000-2005 Pontiac Montana
2001-2005 Pontiac Aztek
2005-2007 Pontiac Montana SV6
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 453
Chevrolet Venture V6-3.4L VIN E 2778
2005-2007 Saturn Relay

Supercede:

This bulletin is being revised to add 2007 model year. Also, additional information was added to the Important statement. Please discard Corporate
Bulletin Number 01-08-45-005D (Section 8 - Body and Accessories).

Condition

Some customers may comment on one or more of the following conditions:

Engine is hard to start

Engine will not start

Engine starts then stalls

Fuel gauge is inoperative or fluctuates

Service Engine Soon/Check Engine light is illuminated

ABS Warning Light is illuminated

TCS Warning Light is illuminated

TCS activation

Service Traction System message displayed

All-Wheel Drive Disable message displayed

These conditions may be intermittent. Upon investigation, the technician may find various DTCs set.

Cause

This condition may be due to water leaking into the interior of the vehicle, and/or spread terminals, at connector C305 that is located on the floor to
the rear of the driver's seat. This connector is not sealed from the inside of the vehicle and water may enter the connector causing the terminals to
become corroded. Also, the female terminals of the connector may have become spread apart causing an intermittent poor connection.

Correction

Inspect the terminals at connector C305 for corrosion or spreading before replacing the fuel module or resistor card kit. Terminals can be accessed
from underneath the vehicle.

Do not attempt to repair any spread female terminals as this will result in a return repair. The female terminal must be replaced.

If the terminals show signs of corrosion, determine the source of the water leak first and repair the water leak before repairing the terminals in
connector C305. Refer to Corporate Service Bulletin Number 01-01-38-009A to determine a potential source for water in the vehicle interior.

Repair any corroded and/or spread female terminals in connector C305. Refer to Repairing Connector Terminals in the Wiring Systems sub-section
of the appropriate service information.

Warranty Information

For vehicles repaired under warranty, use the table.


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 454
Chevrolet Venture V6-3.4L VIN E 2779

Disclaimer
Technical Service Bulletin # 01-08-51-004E Date: 061222

Body - Premature Aluminum Hood Blistering


Subject:
Premature Aluminum Panel Hood Corrosion/Blistering (Refinish)
# 01-08-51-004E - (12/22/2006)

Models:
2000-2003 Buick LeSabre
2002-2006 Buick Rendezvous
2000-2005 Cadillac DeVille
2003-2006 Cadillac CTS
2004-2006 Cadillac SRX
2005-2006 Cadillac STS
2006 Cadillac DTS
1997-2005 Chevrolet Trans Sport (Export Only), Venture
1997-2003 Oldsmobile Silhouette
2001-2003 Oldsmobile Aurora
1997-1998 Pontiac Trans Sport
1997-2005 Pontiac Montana
2000-2003 Pontiac Bonneville

This bulletin is being revised to update the affected model years. Please discard Corporate Bulletin Number O1-08-51-004D (Section 08 - Body and
Accessories).

Condition

Some vehicles may have the appearance of blistering or bubbling paint on the top of the hood or under the hood edges and hem flanges.

Correction

Important:
Always follow your paint manufacturer's instructions for specific product usage.

1. Remove the hood from the vehicle.

2. Wash the complete hood with soap and water.

3. Wash the hood with wax and grease remover.

4. Inspect the hood for paint blistering (top of the hood and under the hood edges and hem flanges).

Important:
Because the hood is made of aluminum only, use clean discs so that the aluminum surface of the hood will not become contaminated with
foreign particles.

5. Clean blister areas by spot media blast or a 3M(R) Roloc clean and strip disc, P/N 07466, or equivalent.

6. Feather edge and clean.

7. Prime the affected area, seal the complete panel perimeter hem flange using 3M # 08370.

8. Refer to your GM 4901M Approved Refinish Materials booklet under the heading of Rigid Substrates (Steel and Aluminum) for product
selection.

The information for the latest GM Approved Refinish Materials booklet is ONLY online at the GM Goodwrench website. Printed books have
been discontinued. Follow these steps to access the site:

^ Go to www.gmgoodwrench.com.

^ Click on GM Collision Parts.


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 455
Chevrolet Venture V6-3.4L VIN E 2780

^ Click on GM Technical Repair Information.

^ Click on Paint Shop.

Warranty Information

For vehicles repaired under warranty, use the table.

Disclaimer
Technical Service Bulletin # 00-06-02-006D Date: 060815

Cooling System - Coolant Recycling Information


Bulletin No.: 00-06-02-006D

Date: August 15, 2006

INFORMATION

Subject:
Engine Coolant Recycling and Warranty Information

Models:
2007 and Prior GM Passenger Cars and Trucks (Including Saturn)
2007 and Prior HUMMER Vehicles
2005-2007 Saab 9-7X

Attention:
Please address this bulletin to the Warranty Claims Administrator and the Service Manager.

Supercede:

This bulletin is being revised to adjust the title and Include Warranty Information. Please discard Corporate Bulletin Number 00-06-02-006C
(Section 06 - Engine/Propulsion System).

Coolant Reimbursement Policy

General Motors supports the use of recycled engine coolant for warranty repairs/service, providing a GM approved engine coolant recycling system
is used. Recycled coolant will be reimbursed at the GMSPO dealer price for new coolant plus the appropriate mark-up. When coolant replacement
is required during a warranty repair, it is crucial that only the relative amount of engine coolant concentrate be charged, not the total diluted
volume. In other words: if you are using two gallons of pre-diluted (50:50) recycled engine coolant to service a vehicle, you may request
reimbursement for one gallon of GM Goodwrench engine coolant concentrate at the dealer price plus the appropriate warranty parts handling
allowance.

Licensed Approved DEX-COOL(R) Providers

Important:
USE OF NON-APPROVED VIRGIN OR RECYCLED DEX-COOL(R) OR DEVIATIONS IN THE FORM OF ALTERNATE CHEMICALS
OR ALTERATION OF EQUIPMENT, WILL VOID THE GM ENDORSEMENT, MAY DEGRADE COOLANT SYSTEM INTEGRITY
AND PLACE THE COOLING SYSTEM WARRANTY UNDER JEOPARDY.
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 456
Chevrolet Venture V6-3.4L VIN E 2781

Shown in Table 1 are the only current licensed and approved providers of DEX-COOL(R). Products that are advertised as "COMPATIBLE" or
"RECOMMENDED" for use with DEX-COOL(R) have not been tested or approved by General Motors. Non-approved coolants may degrade the
coolant system integrity and will no longer be considered a 5 yr/150,000 mile (240,000 km) coolant.

Coolant Removal Services/Recycling

The tables include all coolant recycling processes currently approved by GM. Also included is a primary phone number and demographic
information. Used DEX-COOL(R) can be combined with used conventional coolant (green) for recycling. Depending on the recycling service
and/or equipment, it is then designated as a conventional 2 yr/30,000 mile (50,000 km) coolant or DEX-COOL(R) 5 yr/150,000 mile (240,000 km)
coolant. Recycled coolants as designated in this bulletin may be used during the vehicle(s) warranty period.

DEX-COOL(R) Recycling

The DEX-COOL(R) recycling service listed in Table 2 has been approved for recycling waste engine coolants (DEX-COOL) or conventional) to
DEX-COOL(R) with 5 yr/150,000 mile (240,000 km) usability. Recycling Fluid Technologies is the only licensed provider of Recycled
DEX-COOL(R) meeting GM6277M specifications and utilizes GM approved inhibitor packages. This is currently a limited program being
monitored by GM Service Operations which will be expanded as demand increases.

Conventional (Green) Recycling


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 457
Chevrolet Venture V6-3.4L VIN E 2782

Processes shown in the Table 3 are capable of recycling waste engine coolants (DEX-COOL(R) or conventional) to a conventional (green) coolant.
Recycling conventional coolant can be accomplished at your facility by a technician using approved EQUIPMENT (listed by model number in
Table 3), or by an approved coolant recycling SERVICE which may recycle the coolant at your facility or at an offsite operation. Refer to the table
for GM approved coolant recyclers in either of these two categories. Should you decide to recycle the coolant yourself, strict adherence to the
operating procedures is imperative. Use ONLY the inhibitor chemicals supplied by the respective (GM approved) recycling equipment
manufacturer.

Sealing Tablets

Cooling System Sealing Tablets (Seal Tabs) should not be used as a regular maintenance item after servicing an engine cooling system.
Discoloration of coolant can occur if too many seal tabs have been inserted into the cooling system. This can occur if seal tabs are repeatedly used
over the service life of a vehicle. Where appropriate, seal tabs may be used if diagnostics fail to repair a small leak in the cooling system. When a
condition appears in which seal tabs may be recommended, a specific bulletin will be released describing their proper usage.

Water Quality

The integrity of the coolant is dependent upon the quality of DEX-COOL(R) and water. DEX-COOL(R) is a product that has enhanced protection
capability as well as an extended service interval. These enhanced properties may be jeopardized by combining DEX-COOL(R) with poor quality
water. If you suspect the water in your area of being poor quality, it is recommended you use distilled or de-ionized water with DEX-COOL(R).

"Pink" DEX-COOL(R)

DEX-COOL(R) is orange in color to distinguish it from other coolants. Due to inconsistencies in the mixing of the dyes used with DEX-COOL(R),
some batches may appear pink after time. The color shift from orange to pink does not affect the integrity of the coolant, and still maintains the 5
yr/150,000 mile (240,000 km) service interval.

Back Service

Only use DEX-COOL(R) if the vehicle was originally equipped with DEX-COOL(R).

Contamination
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 458
Chevrolet Venture V6-3.4L VIN E 2783

Mixing conventional green coolant with DEX-COOL(R) will degrade the service interval from 5 yrs./150,000 miles (240,000 km) to 2 yrs./30,000
miles (50,000 km) if left in the contaminated condition. If contamination occurs, the cooling system must be flushed twice immediately and re-filled
with a 50/50 mixture of DEX-COOL(R) and clean water in order to preserve the enhanced properties and extended service interval of
DEX-COOL(R).

After 5 years/150,000 miles (240,000 km)

After 5 yrs/150,000 miles (240,000 km), the coolant should be changed, preferably using a coolant exchanger. If the vehicle was originally
equipped with DEX-COOL(R) and has not had problems with contamination from non-DEX-COOL(R) coolants, then the service interval remains
the same, and the coolant does not need to be changed for another 5 yrs/150,000 miles (240,000 km)

Equipment (Coolant Exchangers)

The preferred method of performing coolant replacement is to use a coolant exchanger. A coolant exchanger can replace virtually all of the old
coolant with new coolant. Coolant exchangers can be used to perform coolant replacement without spillage, and facilitate easy waste collection.
They can also be used to lower the coolant level in a vehicle to allow for less messy servicing of cooling system components. It is recommended
that you use a coolant exchanger with a vacuum feature facilitates removing trapped air from the cooling system. This is a substantial time savings
over repeatedly thermo cycling the vehicle and topping-off the radiator. The vacuum feature also allows venting of a hot system to relieve system
pressure. Approved coolant exchangers are available through the GMDE (General Motors Dealer Equipment) program.

For refilling a cooling system that has been partially or fully drained for repairs other than coolant replacement, the Vac-N-Fill Coolant Refill Tool
(GE-47716) is recommended to facilitate removal of trapped air from the cooling system during refill.

DisclaimerTechnical Service Bulletin # 06-01-39-007 Date: 060725

A/C - Contaminated R134A Refrigerant


Bulletin No.: 06-01-39-007

Date: July 25, 2006

INFORMATION

Subject:
Contaminated R134a Refrigerant Found on Market for Automotive Air-Conditioning Systems

Models:
2007 and Prior GM Passenger Cars and Trucks (including Saturn)
2007 and Prior HUMMER H2, H3
2007 and Prior Saab 9-7X

Attention:
This bulletin should be directed to the Service Manager as well as the Parts Manager.

Commercially Available Contaminated R134a Refrigerant

Impurities have been found in new commercially available containers of R134a. High levels of contaminates may cause decreased performance,
and be detrimental to some air-conditioning components. Accompanying these contaminates has been high levels of moisture.

Tip:

Excessive moisture may cause system concerns such as orifice tube freeze-up and reduced performance.

Industry Reaction: New Industry Purity Standards

Due to the potential availability of these lower quality refrigerants, the Society of Automotive Engineers (SAE), and the Air Conditioning and
Refrigeration Industry (ARI) are in the process of instituting reliable standards that will be carried on the labels of future R134a refrigerant
containers. This identifying symbol will be your assurance of a product that conforms to the minimum standard for OEM Automotive
Air-Conditioning use.

How Can You Protect Yourself Today?


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 459
Chevrolet Venture V6-3.4L VIN E 2784

It is recommended to use GM or ACDelco(R) sourced refrigerants for all A/C repair work. These refrigerants meet General Motors own internal
standards for quality and purity, insuring that your completed repairs are as good as the way it left the factory.

Parts Information

The part numbers shown are available through GMSPO or ACDelco(R). The nearest ACDelco(R) distributor in your area can be found by calling
1-800-223-3526 (U.S. Only).

DisclaimerTechnical Service Bulletin # 01-07-31-002B Date: 061101

M/T - Hydraulic Clutch Bleeding Procedure Improvement


Bulletin No.: 01-07-31-002B

Date: November 01, 2006

INFORMATION

Subject:
Improved Bleeding Procedure for Hydraulic Clutch Release System

Models:
2007 and Prior GM Passenger Cars and Light Duty Trucks (including Saturn)
2007 and Prior Chevrolet and GMC 6-7F T-Series Medium Duty Tilt Cab Models
2007 and Prior Isuzu F-Series Medium Duty Tilt Cab Models
2006-2007 HUMMER H3

Supercede:

This bulletin is being revised to add model years. Please discard Corporate Bulletin Number 01-07-31-002A (Section 07 - Transmission/Transaxle).
This bulletin is being issued to inform dealers of an improved procedure to aid in the ease of bleeding the clutch hydraulic system for the above
listed vehicles. This procedure can be used anytime air is introduced into the hydraulic system. Following this procedure may also reduce the
number of unnecessary parts replaced for low clutch pedal reserve and high shift effort.

Verify that all the lines and fittings are dry and secure.

Clean the dirt and grease from the reservoir cap in order to ensure that no foreign substances enter the system.

Remove the reservoir cap.

Fill the reservoir to the proper level with the required fluid.

Attach the J 43485 (Adapter) to the J 35555 (Mity Vac), or equivalent.

Brake fluid will deteriorate the rubber on J 43485. Use a clean shop cloth to wipe away the fluid after each use.
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 460
Chevrolet Venture V6-3.4L VIN E 2785

Place and hold the adapter on the reservoir filler neck to ensure a tight fit. In some cases, the adapter will fit into the reservoir opening.

Apply a vacuum of 51-68 kPa (15-20 hg) and remove the adapter.

Refill the reservoir to the proper level.

Repeat Steps 6 and 7.

If needed, refill the reservoir and continue to pull a vacuum until no more bubbles can be seen in the reservoir or until the fluid level no longer
drops.

The vehicle will move if started in gear before the Actuator Cylinder is refilled and operational. Start the vehicle the first time in neutral to help
prevent personal injury from vehicle movement and see if the transmission will shift easily into gear.

Pump the clutch pedal until firm (to refill actuator cylinder).

Add additional fluid if needed.

Test drive vehicle to ensure proper operation.

Disclaimer
Technical Service Bulletin # 06-08-46-007 Date: 061213

OnStar - Analog-Only Systems Information


Bulletin No.: 06-08-46-007

Date: December 13, 2006

INFORMATION

Subject:
Information on OnStar(R) Analog-Only Systems

Models:
1996-2001 GM Passenger Cars and Trucks

Plus:
2002 Buick LeSabre, Rendezvous
2002-2003 Buick Century, Regal
2002-2005 Buick Park Avenue
2002 Cadillac Eldorado, Escalade Models
2002 Chevrolet Avalanche, Silverado, Suburban, Tahoe, Venture
2002 GMC Denali, Denali XL, Jimmy, Sierra, Yukon, Yukon XL
2002 Oldsmobile Intrigue, Silhouette
2002-2003 Oldsmobile Aurora
2002 Pontiac Aztek, Bonneville, Montana
2002-2003 Pontiac Grand Prix

with OnStar(R) (RPO UE1)

All vehicles equipped with OnStar(R) listed in this bulletin were built with Analog-Only OnStar(R) Hardware. OnStar(R) equipped vehicles with
analog-only equipment were designed to operate only on the analog wireless network and cannot be upgraded for digital network compatibility.

Vehicles with this equipment will no longer be able to receive OnStar(R) services beginning January 1, 2008. At that time, service will be available
only through Dual-Mode (Analog/Digital) equipment. Analog-Only vehicles cannot be upgraded to digital equipment.
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 461
Chevrolet Venture V6-3.4L VIN E 2786

DisclaimerTechnical Service Bulletin # 04-07-30-013B Date: 070201

Engine, A/T - Shift/Driveability Concerns/MIL ON


Bulletin No.: 04-07-30-013B

Date: February 01, 2007

INFORMATION

Subject:
Automatic Transmission Shift, Engine Driveability Concerns or Service Engine Soon (SES) Light On as a Result of the Use of an
Excessively/Over-Oiled Aftermarket, Reusable Air Filter

Models:
2007 and Prior GM Cars and Light Duty Trucks
2007 and Prior Saturn Models
2003-2007 HUMMER H2
2006-2007 HUMMER H3
2005-2007 Saab 9-7X

Supercede:

This bulletin is being revised to add models and model years. Please discard Corporate Bulletin Number 04-07-30-013A (Section 07 -
Transmission/Transaxle).

The use of an excessively/over-oiled aftermarket, reusable air filter may result in:

Service Engine Soon (SES) light on

Transmission shift concerns, slipping and damaged clutch(es) or band(s)

Engine driveability concerns, poor acceleration from a stop, limited engine RPM range

The oil that is used on these air filter elements may be transferred onto the Mass Air Flow (MAF) sensor causing contamination of the sensor. As a
result, the Grams per Second (GPS) signal from the MAF may be low and any or all of the concerns listed above may occur.

When servicing a vehicle with any of these concerns, be sure to check for the presence of an aftermarket reusable, excessively/over-oiled air filter.
The MAF, GPS reading should be compared to a like vehicle with an OEM air box and filter under the same driving conditions to verify the
concern.

The use of an aftermarket reusable air filter DOES NOT void the vehicle's warranty.

If an aftermarket reusable air filter is used, technicians should inspect the MAF sensor element and the air induction hose for contamination of oil
prior to making warranty repairs.

Transmission or engine driveability concerns (related to the MAF sensor being contaminated with oil) that are the result of the use of an aftermarket
reusable, excessively/over-oiled air filter are not considered to be warrantable repair items.
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 462
Chevrolet Venture V6-3.4L VIN E 2787

DisclaimerTechnical Service Bulletin # 07-08-44-007 Date: 070417

Navigation System - Replacement Navigation Discs


Bulletin No.: 07-08-44-007

Date: April 17, 2007

INFORMATION

Subject:
Information on Obtaining Replacement Navigation Discs When Radios are Exchanged - Order Replacement Navigation Disc Through Navigation
Disc Center

Models:
2007 and Prior GM Passenger Cars and Trucks (Including Saturn)
2007 and Prior HUMMER H2, H3
2007 and Prior Saab 9-7X

with a Navigation Radio

Attention:
The purpose of this bulletin is to inform dealership personnel of a new procedure for obtaining a replacement navigation disc for radios that are
sent to an ESC for exchange. This bulletin applies to U.S. and Canadian dealers only and is not intended for use by export dealers.

When a navigation radio warranty exchange is performed, the customer must have a navigation disc to operate the new radio. If the customer's
navigation disc was damaged or is stuck in the failed radio, the customer would have to wait for an excessive period of time for the disc to be
returned or replaced. The Electronic Service Centers (ESC) are not authorized to remove stuck navigation discs from cores, as the cores must be
returned to the supplier for analysis prior to any disassembly. The time it would take for the supplier to return the navigation disc would
significantly delay the completion of the repair at the dealership.

If the customer's navigation disc is damaged or cannot be removed from the radio, the dealership is to obtain an exchange radio through an ESC and
a new navigation disc through the GM Navigation Disc Center. Both items can be shipped overnight to the dealership upon request.

GM Navigation Disc Center Contact Information

Via the web through gmnavdisc.com

The GM Navigation Disc Center is also the center of expertise for navigation system questions.

Warranty Information

Include the part number and cost of the new navigation disc on the warranty claim for the navigation radio exchange.

Disclaimer
Technical Service Bulletin # 02-08-42-004A Date: 070330

Instruments - Reduced PRNDL Display Visibility


Bulletin No.: 02-08-42-004A

Date: March 30, 2007

INFORMATION

Subject:
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 463
Chevrolet Venture V6-3.4L VIN E 2788
PRNDL Display Reduced Visibility For Approximately One Minute

Models:
2007 and Prior Passenger Cars and Trucks (Including Saturn)
2007 and Prior HUMMER H2, H3
2005-2007 Saab 9-7X

with Automatic Headlamp Control and Vacuum Fluorescent PRNDL Indicator Instrument Panel Cluster

Supercede:

This bulletin is being revised to include additional models and model years. Please discard Corporate Bulletin Number 02-08-42-0004 (Section 08 -
Body and Accessories).

After backing the vehicle out of a garage or dark environment into a daylight environment, the PRNDL display has reduced visibility for
approximately one minute.

While the vehicle is parked in a dark environment, the sensor for the automatic headlamp/driving lamps senses that it is dark. When the key is
turned to the run/start position, the automatic headlamp module will turn all driving lamps, the instrument panel cluster and PRNDL display ON in
the night-time mode. The night-time mode intensity of the instrument panel lamps and PRNDL display is controlled by the automatic headlamp
module and can be dimmed further by the customer using the dimming control of the headlamp switch.

When the customer then moves the vehicle from the dark environment into the bright sunlight, it will take approximately one minute before the
headlamp control module recognizes this as true daylight and not just a bright overhead street lamp shining on the sensor. The headlamp control
module will then turn the headlamps off and restore the instrument panel and PRNDL display to full brilliance.

Without the time delay, the automatic headlamp control module would switch to the night mode (turn on all driving lamps, instrument panel lamps
and PRNDL display would dim) each time the vehicle was driven under an overpass or other darkened environment.

This is a normal condition and no repair should be attempted.

Ensure the instrument panel backlighting control is in the full bright position. This will help alleviate the condition. You may demonstrate to the
customer what happens by placing a repair order over the automatic headlamp control light sensor, which will cause the automatic headlamp
control module to switch to the night mode in approximately one minute. All driving lamps will come ON, the instrument panel backlight will be
dim, and the PRNDL display will also dim to the night setting in conjunction with the position of the headlamp switch dimming control.
Demonstrate to the customer the variance in the instrument panel backlighting and PRNDL display while adjusting the headlamp switch dimming
control to both ends of its allowable range. Advise the customer to keep the headlight switch dimming control in the highest position to allow
viewing of the PRNDL display in a bright environment.

DisclaimerTechnical Service Bulletin # 07-08-63-001 Date: 070417

Body - Polypropylene Energy Absorber Replacement


Bulletin No.: 07-08-63-001

Date: April 17, 2007

INFORMATION

Subject:
Information on Repair of Polypropylene Energy Absorbers

Models:
2007 and Prior GM Passenger Cars and Trucks (including Saturn)
2007 and Prior HUMMER H2, H3
2005-2007 Saab 9-7X

Supercede:

This bulletin is being revised to change the repair information. Please discard Corporate Bulletin Number 63-20-02 (Section 8 - Body and
Accessories).

Because the energy absorbers are relatively low in cost to replace, it is now more cost efficient to replace the energy absorbers whenever they are
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 464
Chevrolet Venture V6-3.4L VIN E 2789
damaged.

DisclaimerTechnical Service Bulletin # 05-06-01-010B Date: 070928

Engine - Sealant Usage/Procedures


Bulletin No.: 05-06-01-010B

Date: September 28, 2007

INFORMATION

Subject:
Service Information Update on Consolidating Use of GM Liquid Gasket/Engine Sealants and New Sealant Dispenser GE-48326 Essential Tool

Models:
2008 and Prior GM Passenger Cars and Trucks (including Saturn)
2003-2008 HUMMER H2
2006-2008 HUMMER H3
2005-2008 Saab 9-7X

with Gasoline or Diesel Engines

Supercede:

This bulletin is being updated to add additional information about the use by date code printed on the crimp of the sealant tube. Please discard
Corporate Bulletin Number 05-06-01-010A (Section 06 - Engine/Propulsion System).

In 2005 General Motors consolidated the use of all liquid gaskets/engine sealants. At that time, two sealants replaced all previous sealants referred
to in Service Information (SI) and/or the Service Manual.

In 2007, GM has consolidated to one engine sealant already available in a 150 g cartridge and now in a 75 g aluminum tube. As a result, P/N
12346141, 54 g tube, has been deleted from service.

One of these, engine sealant P/N 12378521 (U.S.) and P/N 88901148 (Canada), was released in a cartridge to be used in a conventional caulking
gun. The cartridge and conventional caulking gun proved to be too large and cumbersome in certain instances when used in on-vehicle service.

To address this concern, GM Powertrain Engineering released the engine sealant in a 0.075 kg (75 gram) squeeze tube (packaged six to the carton,
with nozzles) along with a new essential service tool, Sealant Dispenser GE-48326, which has been shipped to all GM dealerships.

Sealant Guidelines

The GM Powertrain engineering specification for applying this sealant is an even bead, 3 mm (0.118 in) in diameter. Due to the high viscosity of
the sealant, a dispenser is required to meet this specification. The GE-48326 Sealant Dispenser provides the ability to apply the sealant to
specification using one hand, even in areas not accessible using the P/N 12378521 Engine Sealant cartridge and caulking gun.

This solitary engine sealant available in tubes and small cartridge is compatible with all synthetic, synthetic blends and mineral oils, as well as all
engine coolants including DEX-COOL(R). The maximum working time of this sealant is 20 minutes. The sealant will be fully cured in 24 hours.
The assembly may be filled with oil or coolant immediately after applying the sealant and tightening the bolts.

Engine Sealant Part Numbers


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 465
Chevrolet Venture V6-3.4L VIN E 2790

Use By Date Code

The 0.075 kg (75 gram) Squeeze Tube is not available for 2008 and prior Saturn models (only in 150 g cartridges).

The "use by" date on the 0.15 kg (150 gram) cartridge currently is not available.

The use by date of the 0.075 kg (75 gram) tube is twelve months from the manufacture date printed on the crimp month (1), date (2), year (3).
GMSPO recommends that dealers use the first-in first out (FIFO) system of stock rotation on chemicals. Use the oldest stock first by rotating the
oldest to the front of a stock location.

Special Service Tool GE-48326 Sealant Dispenser

New Engine Sealant 0.075 kg (75 gram) Squeeze Tube (also available in Vehicle Care label for US dealers)

New Sealant and Sealant Dispenser GE-48326

Engine Sealant 0.075 kg (75 gram) Squeeze Tube is not available for 2008 and prior Saturn models (only in 150 g cartridges).

The following service procedures will assist technicians in the proper use of the new sealant dispenser GE-48326 in applying an even bead of
sealant 3 mm (0.118 in) in diameter using one hand, even in areas not accessible using engine sealant cartridge and caulking gun.
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 466
Chevrolet Venture V6-3.4L VIN E 2791

To use the sealant dispenser correctly, install the two white tabs on the rear handle (1) over the front handle. The white paint marks are for
demonstration purposes only. Now your dispenser is ready to install engine sealant 0.075 kg (75 gram) squeeze tube.

Before installing engine sealant 0.075 kg (75 gram) squeeze tube into the dispenser, install a small piece of medium grit sandpaper, or equivalent,
by folding it over the bottom of the squeeze tube (1). This will help hold the squeeze tube firmly in place while using the sealant dispenser.

Install engine sealant 0.075 kg (75 gram) squeeze tube with a small piece of medium grit sandpaper into the dispenser (see above graphic
illustration). Remember to open the squeeze tube with a sharp knife or equivalent and cut the sealant nozzle to the correct diameter to apply a 3 mm
(0.118 in) even bead of sealant.

The sealant dispenser with the engine sealant is now ready to be used (see above graphic illustration).
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 467
Chevrolet Venture V6-3.4L VIN E 2792

DisclaimerTechnical Service Bulletin # 05-06-01-019F Date: 071002

Engine - Oil Leaks from Crankshaft Rear Main Seal


Bulletin No.: 05-06-01-019F

Date: October 02, 2007

TECHNICAL

Subject:
Engine Oil Leak at Crankshaft Rear Main Oil Seal (Install Revised Crankshaft Rear Main Oil Seal Using Revised Rear Main Seal Installer and
Remover Tools)

Models:
1986-2008 GM Passenger Cars and Light Duty Trucks (including Saturn)

with 2.8L, 3.1L, 3.4L, 3.5L, 3.9L 60 Degree V6 Engine (VINs D, E, F, J, K, L, M, N, R, S, T, V, W, X, Z, 1, 3, 8, 9, W, R - RPOs LG6, LA1, LNJ,
LG8, LL1 or LX9, L82, LL2, LB8, LHO, LG5, LB6, LE2 or LQ1, LH7, LC1, L44, LZ4, LZE, LZ9, LGD, LZ8, LZG)

Supercede:

This bulletin is being revised to add an Important statement on proper seal installation. Please discard Corporate Bulletin Number 05-06-01-019E
(Section 06 - Engine/Propulsion System).

This bulletin only applies to 60 degree V6 engines. Some of the discontinued 60 degree V6 engine VINs and RPOs may have carried over to other
new model year engines and may no longer be a 60 degree V6 engine. So this bulletin may not apply. It is very important to verify that the
following information is correct before using this bulletin:

Year of vehicle (e.g. N = 1992)

V6 Engine Liter size (e.g. 3.4L)

VIN CODE (e.g. X)

RPO (e.g. LQ1)

If ALL the information from the vehicle (year, size, VIN Code, RPO) you're working on can be found under the models listed above, then this
bulletin applies to that engine. If one or more of the vehicle's information can NOT be found under the models listed above, then this bulletin does
NOT apply.

This bulletin does not apply to 2004-2007 Saturn VUE models with 3.5L DOHC V6 Engine (VIN 4 - RPO L66) or 2005-2008 Cadillac CTS with
2.8L HFV6 Engine (VIN T - RPO LP1).

Condition

Some customers may comment on external oil leakage.

Correction

Before replacement of the new design crankshaft rear main oil seal, be sure the PCV system is operating correctly. The new seal described below
comes with a protective nylon sleeve already installed in the seal. This sleeve assures that the seal is installed in the correct direction and also
protects the seal from getting damaged during installation. Do not remove the protective sleeve from the seal; if removed, the installation tool
(EN48108) will not work.

A new design crankshaft rear main oil seal and installation tool (EN-48108) has been released. This seal incorporates features that improve high
mileage durability. Replace the crankshaft rear main oil seal with the new design rear main oil seal, P/N 12592195, using the following service
procedures.

Tools Required

TOOLS WERE SHIPPED TO YOUR DEALERSHIPS. IF YOU HAVE NOT RECEIVED THEM OR THEY ARE LOST, PLEASE CALL GM
SPECIAL SERVICE TOOLS AT 1-800-GM-TOOLS.
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 468
Chevrolet Venture V6-3.4L VIN E 2793

EN-48108 Rear Main Oil Seal Installation Tool

This tool has a unique design to allow the technician to easily install the rear main seal squarely to the correct depth and direction. Before
proceeding with installation, review the above illustration to become familiar with the components shown in the illustration.
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 469
Chevrolet Venture V6-3.4L VIN E 2794

EN-48672 rear Main Oil Seal Remover Tool

This tool has a unique design to allow the technician to easily remove the rear main seal without nicking the crankshaft sealing surface when
removing the seal. Before proceeding with removal, review the above illustration to become familiar with the following components:

Removal Plate

Threaded Adjustment Pins and Jam Nuts

Force Screw

# 2 Self Drill Screws 38 mm (1.5 in) long 8 needed

Extreme Pressure Lubricant

Removal Procedure

Remove the transmission. Refer to Transmission Replacement in SI or the appropriate Service Manual.

Remove the engine flywheel. Refer to Engine Flywheel Replacement in SI or the appropriate Service Manual.

Install the removal plate (2) and both threaded adjustment pins and jam nuts (1) into the back of the crankshaft flange and secure the plate with
adjustment pins and jam nuts.
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 470
Chevrolet Venture V6-3.4L VIN E 2795

Install # 2 Self Drill Screws 38 mm (1.5 in) long, eight needed, (1) and tighten down flush to the plate.

Before installing the force screw, apply a small amount of the Extreme Pressure Lubricant J 23444-A, provided in the tool kit.

Install the force screw (1) and back off both jam nuts (2) and continue to turn the force screw (1) into the removal plate to remove the seal from the
crankshaft.
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 471
Chevrolet Venture V6-3.4L VIN E 2796

Once the seal is removed from the crankshaft, remove and save all eight screws and discard the old seal.

Clean the crankshaft sealing surface with a clean, lint free towel. Inspect the lead-in edge of the crankshaft for burrs or sharp edges that could
damage the rear main oil seal. Remove any burrs or sharp edges with crocus cloth or equivalent before proceeding.

Installation Procedure

Do not remove the protective nylon sleeve from the new rear main seal prior to installation. The EN-48108 is designed to install the rear main seal
with the protective sleeve in place. Never apply or use any oil, lubricants or sealing compounds on the crankshaft rear main oil seal.

Align the mandrel dowel pin (EN-48108) to the dowel pin hole in the crankshaft. Refer to the above illustration.

Using a large flat-bladed screwdriver, tighten the two mandrel screws to the crankshaft. Ensure that the mandrel is snug to the crankshaft hub. Refer
to the above illustration.
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 472
Chevrolet Venture V6-3.4L VIN E 2797

Different types (styles) of rear main seals were used in production in different model years, engines and manufacturing facilities. As a result, the
NEW style rear main seal that you will be installing may have a different appearance or shape than the one removed. Regardless of what type of
seal was removed and what side was facing outside the engine, the new seal must be installed as described. Upon close inspection of the outer lip
on the new seal, the words this side out" will be seen. This side of the seal must be facing OUTSIDE the engine when correctly installed. While this
may seem backwards, it is correct. In addition, the protective nylon (plastic) sleeve that the seal is mounted on in the package was designed so that
the seal can only be installed in the proper direction when using the installation tool described in the following steps.

Install the rear main seal (1), with the protective nylon sleeve attached (2), onto the mandrel. The seal, if properly installed, will center on a step
that protrudes from the center of the mandrel. As an error proof, seal will fit only one way onto the mandrel. Refer to the above illustration.

Before installing the outer drive drum, bearing, washer and the drive nut onto the threaded shaft, apply a small amount of the Extreme Pressure
Lubricant J 23444-A, provided in the tool kit.

Install the outer drive drum onto the mandrel (EN-481 08). Install the bearing, washer and the drive nut onto the threaded shaft. Refer to the above
illustration.

Using a wrench, turn the drive nut on the mandrel (EN-48108), which will push the seal into the engine block bore. Turn the wrench until the drive
drum is snug and flush against the engine block. Refer to the above illustration.
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 473
Chevrolet Venture V6-3.4L VIN E 2798

Loosen and remove the drive nut, washer, bearing and drive drum. Discard the protective nylon sleeve.

Verify that the seal has seated properly.

Use a flat-bladed screwdriver to remove the two attachment screws from the mandrel and remove the mandrel from the crankshaft hub. Refer to the
above illustration.

Install the engine flywheel. Refer to Engine Flywheel Replacement in SI or the appropriate Service Manual.

Install the transmission. Refer to Transmission Replacement in SI or the appropriate Service Manual.

Inspect for proper fluid levels.

Inspect for leaks.

Parts Information

Warranty Information

For vehicles repaired under warranty, use the table.

Disclaimer
Technical Service Bulletin # 07-08-45-002 Date: 070905
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 474
Chevrolet Venture V6-3.4L VIN E 2799
Electrical - Aftermarket Fuse Warning
Bulletin No.: 07-08-45-002

Date: September 05, 2007

ADVANCED SERVICE INFORMATION

Subject:
Service Alert: Concerns With Aftermarket Fuses in GM Vehicles

Models:
2008 and Prior GM Passenger Cars and Light Duty Trucks (including Saturn)
2008 and Prior HUMMER H2, H3
2008 and Prior Saab 9-7X

Concerns with Harbor Freight Tools "Storehouse" Branded Blade Type Fuses

General Motors has become aware of a fuse recall by Harbor Freight Tools/Storehouse for a variety of aftermarket fuses. In two cases, these fuses
have not provided protection for the wiring system of the vehicles they were customer installed in.

Upon testing the 15 amp version, it was found that the fuse still would not "open" when shorted directly across the battery terminals.

How to Identify These Fuses

Packed in a 120 piece set, the fuse has a translucent, hard plastic, blue body with the amperage stamped into the top. There are no white painted
numbers on the fuse to indicate amperage. There are no identifying marks on the fuse to tell who is making it. The fuses are known to be distributed
by Harbor Freight Tools but there may be other marketers, and packaging of this style of fuse. It would be prudent to replace these fuses if found in
a customers vehicle. Likewise, if wiring overheating is found you should check the fuse panel for the presence of this style of fuse.

All GM dealers should use genuine GM fuses on the vehicles they service. You should also encourage the use of GM fuses to your customers to
assure they are getting the required electrical system protection. GM has no knowledge of any concerns with other aftermarket fuses. If additional
information becomes available, this bulletin will be updated.

Disclaimer
Technical Service Bulletin # 05-06-04-035C Date: 070730

Fuel System - E85 Fuel Usage Precautions


Bulletin No.: 05-06-04-035C

Date: July 30, 2007

INFORMATION

Subject:
Usage of E85 Fuels in GM Vehicles

Models:
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 475
Chevrolet Venture V6-3.4L VIN E 2800
1997-2008 GM Passenger Cars and Trucks (including Saturn)
2003-2008 HUMMER H2
2006-2008 HUMMER H3
1997-2008 Isuzu NPR Commercial Medium Duty Trucks
2005-2008 Saab 9-7X

Supercede:

This bulletin is being revised to add the 2008 model year and additional engines with E85 capability. Please discard Corporate Bulletin Number
05-06-04-035B (Section 06 - Engine/Propulsion System).

Customer Interest in E85 Fuel

As the retail price of gasoline increases, some locations in the country are seeing price differentials between regular gasoline and E85 where E85 is
selling for substantially less than regular grade gasoline. One result of this is that some customers have inquired if they are able to use E85 fuel in
non-E85 compatible vehicles.

Only vehicles designated for use with E85 should use E85 blended fuel.

E85 compatibility is designated for vehicles that are certified to run on up to 85% ethanol and 15% gasoline. All other gasoline engines are
designed to run on fuel that contains no more than 10% ethanol.

Use of fuel containing greater than 10% ethanol in non-E85 designated vehicles can cause driveability issues, service engine soon indicators as well
as increased fuel system corrosion.

Using E85 Fuels in Non-Compatible Vehicles

General Motors is aware of an increased number of cases where customers have fueled non-FlexFuel designated vehicles with E85. Fueling
non-FlexFuel designated vehicles with E85, or with fuels where the concentration of ethanol exceeds the ASTM specification of 10%, will result in
one or more of the following conditions:

Lean Driveability concerns such as hesitations, sags and/or possible stalling.

SES lights due to OBD codes.

Fuel Trim codes P0171 and/or P0174.

Misfire codes (P0300).

Various 02 sensor codes.

Disabled traction control or Stability System disabled messages.

Harsh/Firm transmission shifts.

Fuel system and/or engine mechanical component degradation.

Use of fuel containing greater than 10% ethanol in non-E85 designated vehicles can cause driveability issues, service engine soon indicators as well
as increased fuel system corrosion.

If the dealer suspects that a non-FlexFuel designated vehicle brought in for service has been fueled with E85, the fuel in the vehicle's tank should be
checked for alcohol content with tool J 44175. If the alcohol content exceeds 10% the fuel should be drained and the vehicle refilled with gasoline -
preferably one of the Top Tier brands.

Repairs to non-FlexFuel vehicles that have been fueled with E85 are not covered under the terms of the New Vehicle Warranty.

A complete list of GM's FlexFuel vehicles can be found in this Service Bulletin, or at www.livegreengoyellow.com.

E85 Compatible Vehicles


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 476
Chevrolet Venture V6-3.4L VIN E 2801

The only E85 compatible vehicles produced by General Motors are shown.

Only vehicles that are listed in the E85 Compatible Vehicles section of this bulletin and/or www.livegreengoyellow.com are E85 compatible.

All other gasoline and diesel engines are NOT E85 compatible.

Use of fuel containing greater than 10% ethanol in non-E85 designated vehicles can cause driveability issues, service engine soon indicators as well
as increased fuel system corrosion.

Repairs to non-FlexFuel vehicles that have been fueled with E85 are not covered under the terms of the New Vehicle Warranty.

DisclaimerTechnical Service Bulletin # 05-08-46-004B Date: 080108

OnStar(R) - Number Incorrect/Incorrectly Assigned


Bulletin No.: 05-08-46-004B

Date: January 08, 2008

INFORMATION

Subject:
OnStar(R) Phone Number Concerns (Phone Number Incorrect/Assigned to Another Vehicle/Phone) That Occur During Diagnosis of OnStar(R)
System

Models:
2000-2008 GM Passenger Cars and Trucks
2003-2008 HUMMER H2
2006-2008 HUMMER H3
2003-2008 Saturn Vehicles
2005-2008 Saab 9-7X

with OnStar(R) (RPO-UE1)

Supercede:

This bulletin is being revised to add the 2008 model year. Please discard Corporate Bulletin Number 05-08-46-004A (Section 08 - Body and
Accessories).

During diagnosis of an OnStar(R) concern the technician may be told that the OnStar(R) phone number is incorrect or tied to another vehicle and/or
phone of some kind. To resolve these concerns the Tech 2(R) with software version 22.005 (or higher) has the capability to change the OnStar(R)
phone number.

Service Procedure

With the Tech 2(R) build the vehicle to specifications within the Diagnostics area of the Tech 2(R).
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 477
Chevrolet Venture V6-3.4L VIN E 2802

For vehicles with physical-based diagnostics - under Body go to the OnStar(R) section. Then select the Special Functions menu. For vehicles with
functional-based diagnostics - under Body and Accessories go to the Cellular Communication section. Select Module Setup and then Vehicle
Communication Interface Module.

Locate the Program Phone Number prompt and select it. The original phone number will be displayed on the Tech 2(R) screen.

Contact the OnStar(R) team at the GM Technical Assistance Center (TAC) to obtain a new phone number.

Highlight the digits of the phone number one at a time and enter the new phone number using the number keys on the Tech 2(R).

Press the Soft key at the base of the screen for Done once these numbers have been changed on the screen.

Press the Soft key for Done again. The area code or new phone number has now been programmed into the phone.

Cycle the ignition to Off and open the drivers door.

Press the blue OnStar(R) button to make sure that a normal connection can be made to the OnStar(R) call center. If applicable make sure the
Hands-Free Calling (HFC) works properly by making a phone call.

If the system is working properly fax or voicemail a case closing into the OnStar(R) team at TAC with the results. Dealers in Canada should submit
case closing information through the GM infoNET.

Please follow this diagnostic process thoroughly and complete each step. If the condition exhibited is resolved WITHOUT completing every step
the remaining steps do not need to be performed. If the procedure above does not resolve the condition you must contact TAC for further
assistance. This diagnostic approach was developed specifically for this condition and should not automatically be used for other vehicles with
similar symptoms.

Warranty Information (excluding Saab U.S. Models)

For vehicles repaired under warranty use, the table.

Warranty Information (Saab U.S. Models)

For vehicles repaired under warranty use, the table.

Disclaimer
Technical Service Bulletin # 02-08-46-006C Date: 080108

OnStar(R) - Incorrect GPS Position Reported During Call


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 478
Chevrolet Venture V6-3.4L VIN E 2803
Bulletin No.: 02-08-46-006C

Date: January 08, 2008

INFORMATION

Subject:
Incorrect OnStar(R) Global Positioning System (GPS) Location Reported During OnStar(R) Call

Models:
2000-2008 GM Passenger Cars and Light Duty Trucks (including Saturn)
2003-2008 HUMMER H2
2006-2008 HUMMER H3
2005-2008 Saab 9-7X

with OnStar(R)

Supercede:

This bulletin is being revised to add model years. Please discard Corporate Bulletin Number 02-08-46-006B (Section 08 - Body and Accessories).

A small number of the above-mentioned vehicles may exhibit a condition in which the vehicle reports an inaccurate location to the OnStar(R) Call
Center. This condition can only be identified via a button press to the OnStar(R) Call Center by the customer. Call Center personnel will be able to
identify this inaccurate location condition. Customers will then be notified through the mail by OnStar(R) if their vehicle exhibits this condition.
Once this condition has been identified OnStar(R) will instruct the customer to return to the dealership to have this condition corrected.

It is not necessary to reconfigure the vehicle after the following procedure.

In order to correct this condition you must cycle power to the OnStar(R) system. This can be done by either removing the fuses powering the
OnStar(R) system or disconnecting the OnStar(R) module (VCIM) from the vehicle. As a last resort you can disconnect the vehicle's battery.

The power needs to be removed from the system for approximately 15 minutes.

After completing this procedure the vehicle should be taken to an area with an unobstructed view of the sky. The vehicle should be kept running for
approximately 10 minutes to allow the vehicle to reacquire the global positioning system (GPS). Then contact the OnStar(R) Call Center via the
blue OnStar(R) button and ask the advisor to verify the GPS position.

If the OnStar(R) advisor still has an inaccurate GPS location refer to the Navigation Systems and Cellular Communications sub-sections in the
Service Manual in order to diagnose and repair the concern. If the normal diagnostics lead to module replacement you will need to contact
Technical Assistance (TAC) and choose the OnStar(R) prompt. GM OnStar(R) TAC will assist in the diagnosis and if appropriate order a
replacement part. Replacement parts are usually shipped out within 24 hours and a pre-paid return package label will be included for returning the
faulty part. By returning the faulty part you will avoid a significant non-return core charge.

Warranty Information (excluding Saab US Models)

For vehicles repaired under warranty, use the table.

Warranty Information (Saab US Models)


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 479
Chevrolet Venture V6-3.4L VIN E 2804

For vehicles repaired under warranty use, the table.

DisclaimerTechnical Service Bulletin # 00-08-46-004C Date: 080117

OnStar(R) - Re-establishing OnStar(R) Communications


Bulletin No.: 00-08-46-004C

Date: January 17, 2008

INFORMATION

Subject:
Re-establishing Communications with OnStar(R) Center After Battery Disconnect

Models:
2000-2008 GM Passenger Cars and Trucks (Including Saturn and Saab)

with Digital OnStar(R) (RPO UE1)

Supercede:

This bulletin is being revised to add models and model years. Please discard Corporate Bulletin Number 00-08-46-004B (Section 08 - Body and
Accessories).

When servicing any of the above models and a battery cable is disconnected or power to the OnStar(R) Vehicle Communication Interface Module
(VCIM) is interrupted for any reason the following procedure must be performed to verify proper Global Positioning System (GPS) function.

Never swap OnStar(R) Vehicle Communication Interface Modules (VCIM) from other vehicles. Transfer of OnStar(R) modules from other
vehicles should not be done. Each OnStar(R) module has a unique identification number. The VCIM has a specific Station Identification (STID).
This identification number is used by the National Cellular Telephone Network and OnStar(R) systems and is stored in General Motors Vehicle
History files by VIN.

After completing ALL repairs to the vehicle you must perform the following procedure:

Move the vehicle into an open area of the service lot.

Sit in the vehicle with the engine running and the radio turned on for five minutes.

Press the OnStar(R) button in the vehicle.

When the OnStar(R) advisor answers ask the advisor to verify the current location of the vehicle.

If the vehicle location is different than the location the OnStar(R) advisor gives contact GM Technical Assistance (TAC) and choose the OnStar(R)
prompt. GM OnStar(R) TAC will assist in the diagnosis of a failed VCIM and, if appropriate, order a replacement part. Replacement parts are
usually shipped out within 24 hours, and a pre-paid return package label will be included for returning the faulty part. By returning the faulty part,
you will avoid a non-return core charge.
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 480
Chevrolet Venture V6-3.4L VIN E 2805

DisclaimerTechnical Service Bulletin # 07-06-01-023 Date: 071205

Engine - Oil Leaks From Front Crankshaft Seal


Bulletin No.: 07-06-01-023

Date: December 05, 2007

TECHNICAL

Subject:
60 Degree V6 Engine Oil Leak at Crankshaft Front Oil Seal (Use New Crankshaft Front Oil Seal Installer Tool EN-48869)

Models:
1986-2008 GM Passenger Cars and Light Duty Trucks (including Saturn)

with 2.8L, 3.1L, 3.4L, 3.5L or 3.9L 60 Degree V6 Engine

(VINs D, E, F, J, K, L, M, N, R, S, T, V, W, X, Z, 1, 3, 8, 9, W, R - RPOs LG6, LA1, LNJ, LG8, LL1 or LX9, L82, LL2, LB8, LHO, LG5, LB6,
LE2 or LQ1, LH7, LC1, L44, LZ4, LZE, LZ9, LGD, LZ8, LZG)

This bulletin does not apply to 2004-2007 Saturn VUE models with 3.5L DOHC V6 Engine (VIN 4 - RPO L66) or 2005-2008 Cadillac CTS with
2.8L HFV6 Engine (VIN T - RPO LP1).

This bulletin only applies to 60 degree V6 engines. Some of the discontinued 60 degree V6 engine VINs and RPOs may have carried over to other
new model year engines and may no longer be a 60 degree V6 engine. So this bulletin may not apply. It is very important to verify that the
information shown is correct before using this bulletin.

If ALL the information from the vehicle (year, size, VIN Code, RPO) you're working on can be found under the models listed above, then this
bulletin applies to that engine. If one or more of the vehicle's information can NOT be found under the models listed above, then this bulletin does
NOT apply.

Condition

Some customers may comment on external oil leakage.

Correction

Before replacement of the crankshaft front oil seal, be sure the PCV system is operating correctly.

Tools Required

TOOLS WERE SHIPPED TO YOUR DEALERSHIPS. IF YOU HAVE NOT RECEIVED THEM OR THEY ARE LOST, PLEASE CALL GM
SPECIAL SERVICE TOOLS AT 1-800-GM-TOOLS.
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 481
Chevrolet Venture V6-3.4L VIN E 2806

The EN-48869 has a unique design to allow the technician to easily install the front crankshaft seal squarely to the correct depth and direction.
Before proceeding with installation, review the illustration to become familiar with the tool.

Removal Procedure

Remove the crankshaft balancer. Refer to Crankshaft Balancer Replacement in SI.

Use care not to damage the engine front cover or nick the crankshaft.

Remove the crankshaft front oil seal (1) using a suitable tool.

Installation Procedure
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 482
Chevrolet Venture V6-3.4L VIN E 2807

Lubricate the inside of the crankshaft front oil seal (1) with clean engine oil. Then install the seal to the installer body (2).

Align the oil seal and installer body (1) with the engine front cover and crankshaft.

Before installing the force screw, apply a small amount of the Extreme Pressure Lubricant J 23444-A, provided in the tool kit, to the force screw.

Install the drive nut (4) onto the threaded force screw shaft (5), washer (3), and bearing (2). Then install to the installer body (1) and tighten the
force screw to the crankshaft by hand.

Using a wrench, turn the drive nut on the threaded force screw shaft (2), this will push the seal into the engine front cover.
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 483
Chevrolet Venture V6-3.4L VIN E 2808

Continue to turn the drive nut (2) with the wrench until the installer body (1) is snug and flush against the engine front cover.

Loosen and remove the drive nut from the threaded force screw shaft, washer, bearing, and installer body. Verify that the seal has seated properly,
flush against front cover flange (1).

Install the crankshaft balancer. Refer to Crankshaft Balancer Replacement in SI.

Inspect for proper fluid levels.

Inspect for leaks.

Parts Information

Warranty Information

For vehicles repaired under warranty, use the table.


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 484
Chevrolet Venture V6-3.4L VIN E 2809

Disclaimer
Technical Service Bulletin # 05-06-02-002B Date: 080118

Cooling System - DEX-COOL(R) Coolant Leak Detection Dye


Bulletin No.: 05-06-02-002B

Date: January 18, 2008

INFORMATION

Subject:
DEX-COOL(R) Coolant - New Leak Detection Dye J 46366 - Replaces J 29545-6

Models:
1996-2008 GM Passenger Cars and Light/Medium Duty Trucks* (including Saturn)
1997-2008 Isuzu T-Series Medium Duty Tilt Cab Models Built in Janesville and Flint
1999-2008 Isuzu N-Series Medium Duty Commercial Models with 5.7L or 6.0L Gas Engine

2003-2008 HUMMER H2
2006-2008 HUMMER H3
2005-2008 Saab 9-7X

*EXCLUDING 2006 and Prior Chevrolet Aveo, Epica, Optra, Vivant and Pontiac Matiz, Wave

Supercede:

This bulletin is being revised to include additional model years. Please discard Corporate Bulletin Number 05-06-02-002A (Section 06 -
Engine/Propulsion System).

Leak detection dye P/N 12378563 (J 29545-6) (in Canada P/N 88900915) may cause DEX-COOL(R) coolant to appear green in a black vessel
making it appear to be conventional (green) coolant. This may cause a technician to add conventional coolant to a low DEX-COOL(R) system thus
contaminating it. The green DEX-COOL(R) appearance is caused by the color of the leak detection dye which alters the color of the
DEX-COOL(R) coolant.

A new leak detection dye P/N 89022219 (J 46366) (in Canada P/N 89022220) has been released that does not alter the appearance of the
DEX-COOL(R) coolant. When adding the new leak detection dye the color of the DEX-COOL(R) coolant will not change. For detecting leaks on
any system that uses DEX-COOL(R) leak detection dye P/N 89022219 (in Canada P/N 89022220) should be used. The new leak detection dye can
be used with both conventional and DEX-COOL(R) coolant.

Disclaimer
Technical Service Bulletin # 04-07-30-037D Date: 071121

A/T - DEXRON(R)-VI Fluid Information


Bulletin No.: 04-07-30-037D

Date: November 21, 2007

INFORMATION

Subject:
Release of DEXRON(R)-VI Automatic Transmission Fluid (ATF)
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 485
Chevrolet Venture V6-3.4L VIN E 2810

Models

Attention:
DEXRON(R)-VI Automatic Transmission Fluid (ATF) is the only approved fluid for warranty repairs for General Motors
transmissions/transaxles requiring DEXRON(R)-III and/or prior DEXRON(R) transmission fluids.

Supercede:

This bulletin is being revised to update model/model year information. Please discard Corporate Bulletin Number 04-07-30-037C (Section 07 -
Transmission/Transaxle).

MANUAL TRANSMISSIONS/TRANSFER CASES and POWER STEERING

The content of this bulletin does not apply to manual transmissions or transfer cases. Any vehicle that previously required DEXRON(R)-III for a
manual transmission or transfer case should now use P/N 88861800. This fluid is labeled Manual Transmission and Transfer Case Fluid. Power
Steering Systems should now use P/N 9985010 labeled Power Steering Fluid.

Consult the Owner's Manual or Service Information (SI) for fluid recommendations.

Some of our customers and/or General Motors dealerships/Saturn Retailers may have some concerns with DEXRON(R)-VI and DEXRON(R)-III
Automatic Transmission Fluid (ATF) and transmission warranty claims. DEXRON(R)-VI is the only approved fluid for warranty repairs for
General Motors transmissions/transaxles requiring DEXRON(R)-III and/or prior DEXRON(R) transmission fluids. Please remember that the clean
oil reservoirs of the J 45096 - Flushing and Flow Tester machine should be purged of DEXRON(R)-III and filled with DEXRON(R)-VI for testing,
flushing or filling General Motors transmissions/transaxles.

DEXRON(R)-VI can be used in any proportion in past model vehicles equipped with an automatic transmission/transaxle in place of
DEXRON(R)-III (i.e. topping off the fluid in the event of a repair or fluid change). DEXRON(R)-VI is also compatible with any former version of
DEXRON(R) for use in automatic transmissions/transaxles.

DEXRON(R)-VI ATF

General Motors Powertrain has upgraded to DEXRON(R)-VI ATF with the start of 2006 vehicle production.

Current and prior automatic transmission models that had used DEXRON(R)-III must now only use DEXRON(R)-VI.

All 2006 and future model transmissions that use DEXRON(R)-VI are to be serviced ONLY with DEXRON(R)-VI fluid.
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 486
Chevrolet Venture V6-3.4L VIN E 2811

DEXRON(R)-VI is an improvement over DEXRON(R)-III in the areas shown.

2006-2008 Transmission Fill and Cooler Flushing

Some new applications of the 6L80 six speed transmission will require the use of the J 45096 - Flushing and Flow Tester to accomplish
transmission fluid fill. It is highly recommended that the clean oil reservoir of the machine be purged of DEXRON(R)-III and filled with
DEXRON(R)-VI.

Parts Information

Disclaimer
Technical Service Bulletin # 00-06-01-012C Date: 080414

Engine - Use of 'Surface Conditioning Disks'


INFORMATION
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 487
Chevrolet Venture V6-3.4L VIN E 2812

Bulletin No.: 00-06-01-012C

Date: April 14, 2008

Subject:
Use of "Surface Conditioning Disks" When Cleaning Engine Gasket Sealing Surfaces and/or Reused Engine Parts

Models:
2009 and Prior GM Passenger Cars and Trucks (including Saturn)
2009 and Prior HUMMER H2 Models, H3
2009 and Prior Saab 9-7X

Supercede:

This bulletin is being revised to add the 2008 and 2009 model years. Please discard Corporate Bulletin Number 00-06-01-012B (Section 06 -
Engine/Propulsion System).

The Use of "Surface Conditioning Disks"

Notice:
Do not use abrasive pad/bristle devices to clean the gasket surfaces of engine components. Abrasive pads should not be used for the following
reasons:

^ Abrasive pads will produce fine grit that the oil filter will not be able to remove from the oil. THIS GRIT IS ABRASIVE AND HAS BEEN
KNOWN TO CAUSE INTERNAL ENGINE DAMAGE. Abrasive pads can easily remove enough material to round cylinder head surfaces.
This has been known to affect the gaskets ability to seal especially in the narrow seal areas between the combustion chambers and coolant
jackets.

^ Abrasive pads can also remove enough metal to affect cylinder head block oil pan rail and intake manifold runner flatness which can cause
coolant and oil leaks. It takes about 15 seconds to remove 0.203 mm (0.008 in) of metal with an abrasive pad.

When cleaning engine gasket sealing surfaces and/or cleaning parts from an engine that are to be reused surface conditioning disks (typically
constructed of woven fiber or molded bristles) that contain abrasives such as a high amount of Aluminum Oxide should NOT be used.

The use of such surface conditioning disks dislodges Aluminum Oxide (from the disk) and metal particles which can lead to premature engine
bearing failure.

The presence of Aluminum Oxide in engine oil has been shown to cause premature engine bearing failure. In some cases this failure occurs in as
little as 2,200 km (1,000 mi) or less after the repair has been made.

Surface conditioning disks may grind the component material and imbed it into the disk. This can result when more aggressive grinding of the
gasket surface takes place.

Recommended Cleaning Procedure

General Motors recommends the use of a razor blade or plastic gasket scraper to clean the gasket surface on engine components that are to be
reused. When cleaning gasket surfaces please note the following:

^ When using a razor blade type gasket scraper use a new razor blade for each cylinder head and corresponding block surface. Hold the blade as
parallel to the gasket surface as possible. This will ensure that the razor blade does not gouge or scratch the gasket surfaces.

^ Do not gouge or scrape the combustion chamber surfaces.

^ Do not gouge or scratch any engine-sealing surface during the cleaning process.

Important:
The appearance of the gasket surface is not critical - the feel is. There will be indentations from the gasket left in the cylinder head after all the
gasket material is removed. The new gasket will fill these small indentations when it is installed.

DisclaimerTechnical Service Bulletin # 02-06-01-003B Date: 080415

Engine - Revised Cylinder Head Bolt Torque/Sequence


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 488
Chevrolet Venture V6-3.4L VIN E 2813
INFORMATION

Bulletin No.: 02-06-01-003B

Date: April 15, 2008

Subject:
Revised Cylinder Head Bolt Torque Specification and Tightening Sequence

Models:
1994-1998 Buick Skylark
1994-2002 Buick Century, Regal
2002 Buick Rendezvous
1994-1996 Chevrolet Beretta, Corsica, Lumina APV
1994-2000 Chevrolet Camaro, Lumina
1994-2002 Chevrolet Monte Carlo
1997-2002 Chevrolet Malibu, Venture
2000-2002 Chevrolet Impala
1993-1996 Oldsmobile Ciera
1993-1997 Oldsmobile Cutlass Supreme
1994-2002 Oldsmobile Silhouette
1996-1999 Oldsmobile Cutlass
1998 Oldsmobile Achieva
1999-2002 Oldsmobile Alero
1994-2000 Pontiac Firebird, TransSport
1994-2002 Pontiac Grand Am, Grand Prix
1999-2002 Pontiac Montana
2001-2002 Pontiac Aztek

with 3.1L or 3.4L Engine (VINs J, E - RPOs LG8, LA)

Supercede:

This bulletin is being revised to include a Notice advising that the cylinder head bolts are NOT to be re-used. Please discard Corporate Bulletin
Number 02-06-01-003A (Section 06 - Engine).

Notice:
This component uses torque-to-yield bolts. When servicing this component do not re-use the bolts. New torque-to-yield bolts must be installed.
Re-using used torque-to-yield bolts will not provide proper bolt torque and clamp load. Failure to install NEW torque-to-yield bolts may lead to
engine damage.

The cylinder head bolt torque and tightening sequence have been revised. This revision has been made in the SI. If you are using a paper version of
this Service Manual please make a reference to this bulletin on the affected page.

The revised specification is as follows:

Tighten the NEW cylinder head bolts to 60 N.m (44 lb ft) in the order shown. Use the J 36660-A torque angle meter in order to rotate the cylinder
head bolts an additional 95 degrees.

Disclaimer
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 489
Chevrolet Venture V6-3.4L VIN E 2814

Technical Service Bulletin # 04-03-10-012B Date: 080201

Wheels - Chrome Wheel Brake Dust Accumulation/Pitting


Bulletin No.: 04-03-10-012B

Date: February 01, 2008

INFORMATION

Subject:
Pitting and Brake Dust on Chrome wheels

Models:
2008 and Prior GM Passenger Cars and Trucks (including Saturn)
2008 and Prior HUMMER H2, H3
2005-2008 Saab 9-7X

Supercede:

This bulletin is being revised to add model years. Please discard Corporate Bulletin Number 04-03-10-012A (Section 03 - Suspension).

Analysis of Returned Wheels

Chrome wheels returned under the New Vehicle Limited Warranty for pitting concerns have recently been evaluated. This condition is usually most
severe in the vent (or window) area of the front wheels. This "pitting" may actually be brake dust that has been allowed to accumulate on the wheel.
The longer this accumulation builds up, the more difficult it is to remove.

Cleaning the Wheels

In all cases, the returned wheels could be cleaned to their original condition using GM Vehicle Care Cleaner Wax, P/N 12377966 (in Canada, P/N
10952905). When using this product, you should confine your treatment to the areas of the wheel that show evidence of the brake dust build-up.
This product is only for use on chromed steel or chromed aluminum wheels.

Parts Information

Warranty Information

Wheel replacement for this condition is NOT applicable under the terms of the New Vehicle Limited Warranty.

DisclaimerTechnical Service Bulletin # 02-06-03-009C Date: 080417

Electrical - Battery Charging Tips/Recommendations


INFORMATION

Bulletin No.: 02-06-03-009C

Date: April 17, 2008

Subject:
Battery Charging Tips (Includes Information References for HP2 Hybrid Truck [PHT] 42-volt System)

Models:
1990-2009 GM Passenger Cars and Light Duty Trucks (Including Saturn)
2003-2009 HUMMER H2
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 490
Chevrolet Venture V6-3.4L VIN E 2815
2006-2009 HUMMER H3
1990-2009 Isuzu Light Duty Trucks
2005-2009 Saab 9-7X

Supercede:

This bulletin is being revised to add model years. Please discard Corporate Bulletin Number 02-06-03-009B (Section 06 - Engine/Propulsion
System).

When you test a battery with a Midtronics Conductance Tester J 42000 or J 42000-EU (or equivalent for Saturn Retailers) there are five typical
outcomes:

^ Good battery

^ Good - recharge

^ Charge & retest

^ Replace battery

^ Bad cell - replace

You'll notice that battery charging is called for in two of these outcomes. This bulletin will address charging and chargers in more detail.

What's Involved in Charging

Briefly, charging involves applying sufficient voltage to the battery to cause current to flow through the battery. Charging causes a chemical change
in both the batteries plates and the electrolyte. If the battery is simply discharged, but otherwise good, and you apply a suitable current for enough
time, the battery will eventually become as fully charged as is chemically possible. However, continued application of current can lead to
overheating, loss of electrolyte and shortened battery life.

The charging process requires two things: time and current. If you multiply the charging rate in amperes by the number of hours, the result will be
the ampere-hours of charge you've applied to the battery. To bring a battery to full charge will require roughly the same number of ampere-hours at
a low charge rate as it does at a high rate. Put another way, a higher rate will take less time.

Because customers desire to have their vehicles returned quickly, it's often desirable to get the charging job done quickly by using a high charge
rate. Before doing this, though, you need to know a little more about the process.

State of Charge

It is not possible to measure a battery's state of charge in ampere-hours, so another method must be used. Open circuit voltage (OCV), measured
across the battery's terminals, relates to the battery's state of charge. The voltmeter must be capable of reading to the nearest 0.01 volt.

If the battery has NOT been charged or used (the engine started or the vehicle driven) in the last 12 hours, a reading may be taken.

If the battery has been discharged and recharged or used within the last 12 hours, connect a carbon pile and load the battery at 300 amperes for 15
seconds. Remove the load. Wait 15 seconds and then take the reading.

Important:
The OCV reading is accurate +/- 10%.

A battery with a state of charge of 65% or greater ("green eye" showing) is marginally charged enough to be returned to service. However, if the
vehicle is or will be used in slow traffic or short drive times, or in very cold or very hot conditions, the battery should be at least 90% of full charge
before returning to service (the customer).

Battery Charging and the Reality of the Service Lane


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 491
Chevrolet Venture V6-3.4L VIN E 2816

A customer with a "bad" / "discharged" battery typically expects something to be done about it immediately. The customer may not understand that
the battery may be "good" but simply discharged. Customers may want to get back on the road quickly and demand a new battery under warranty.

There are two things wrong with this approach. One, if the battery is otherwise serviceable, it may only need a recharge to return it to health.
Second, unless the cause of the battery becoming discharged is resolved, neither a new battery nor recharging the original will permanently solve
the problem.

Your job, then is to recharge the battery quickly and safely determine and repair, if necessary, the cause of the battery becoming discharged.

Automatic Battery Chargers

Recent advancements in battery charging technology now combine diagnostics and charging control systems that monitor and automatically
regulate the charging process.

These controls maximize the chargers output based on the battery status, while protecting the battery from overcharge. This shortens the overall
time by making the most effective use of the chargers output capability. This means you can confidently use chargers with the highest output
ratings, so long as the charger makes the necessary adjustments as the battery approaches full charge.

Automatic battery chargers such as the Midtronics GR1, Associated Intell/Matic Pro or the Cristie PDQ can return a good, but discharged, battery
(as indicated by your J 42000 tester) to at least 85% state of charge in 20 to 40 minutes. For more information on these chargers, call GM Dealer
Equipment.

Manual Battery Chargers

Non-automatic battery chargers do not offer the self-limiting features of the latest equipment. It is the operators responsibility to control the
charging process. With careful monitoring you can use a manual charger to successfully charge maintenance-free batteries.

Monitor both charging current and voltage every 30 minutes. Because voltage is not held constant, it will rise as the battery becomes charged.

When voltage reaches 16 volts, you must reduce the charging current to 5 amperes. When the voltage reaches 16 volts again, at the 5 amp current,
the battery is fully charged.

Conditions That Affect Charging

A completely discharged battery will take more than twice as long as a half-charged battery to bring the battery to a usable state of charge. The
electrolyte in a discharged battery is largely water, which is a poor conductor. The battery may accept such a small amount of current at first that it
appears not to take charge.

Chemical reactions in a battery are slower at low temperatures. This means a very cold battery will take longer to charge than one at room
temperature.

And, of course, a larger battery will take longer to charge than a small one.

Special Conditions for AGM Batteries

The Absorbent Glass Mat (AGM) battery uses absorbent glass mats to hold a small amount of electrolyte in contact with the plates. The battery uses
a gas recombinant technology, which means the gases produced at the plates are recombined to form water before they escape. This battery design
offers high power for lower weight and is more resistant to high temperatures, vibration and cycling.

The AGM battery may be charged using the automatic battery charger. Laboratory tests have shown that AGM batteries respond very well to such
chargers. In fact, even the chargers with the highest output ratings may be confidently used, as long as the charger automatically adjusts the
charging current as the battery nears full charge. When the charger operation indicates that the battery is fully charged (refer to the charger
manufacturers instructions), remove the battery from charge.

However, when using a conventional charger, limit the rate to 10 amperes or less. Do not allow the battery to charge at 3 amperes or more for
longer than 10 hours, or 10 amperes for longer than 5 hours. When these limits are reached, allow the battery to stand overnight, then resume
charging, if further charging is required.

Check the voltage every 30 minutes and remove the battery from charge when the voltage reaches 15 volts at 3-10 amperes. The state of charge is
now at 90 to 95%.

2004-2007 PHT Trucks Only: The AGM application for the PHT pickup (RPO HP2) involves three such batteries in a 42 volt system, at a 50%
charge. Refer to Battery Inspection/Test (HP2), Battery Pack Service Charge-HP2 and Battery Charging (HP2) procedures in SI for specific
information on hybrid battery systems.
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 492
Chevrolet Venture V6-3.4L VIN E 2817

Disclaimer
Technical Service Bulletin # 05-06-03-002C Date: 080417

Battery/Charging System - Electrical Diagnostics Info.


INFORMATION

Bulletin No.: 05-06-03-002C

Date: April 17, 2008

Subject:
Battery and Charging System Electrical Diagnostics

Models:
1997-2009 GM Passenger Cars and Trucks
2003-2009 HUMMER H2
2006-2009 HUMMER H3

EXCEPT Electric Vehicles and Hybrid Truck

Attention:
This bulletin does not apply to Saturn and Saab models.

Supercede:

This bulletin is being revised to add model years. Please discard Corporate Bulletin Number 05-06-03-002B (Section 06 - Engine/Propulsion
System).

Changing Diagnostic Strategy

The previous electrical diagnostic worksheet provided in GM Corporate Bulletin Numbers 02-06-03-006B, 02-06-03-011 and 02-06-03-012 is no
longer required when diagnosing battery and charging system concerns.

Battery and charging system diagnostic information provided by these bulletins has been incorporated into SI and the printed Service Manuals for
2007 model year and later vehicles.

New Information on Electrical Diagnosis

Specific electrical diagnostics are available for each vehicle line in SI. Please refer to Engine Electrical Diagnostics within Engine Electrical.

New Labor Times for Battery and Generator Diagnostics

With the deletion of the previously required electrical diagnostic worksheet, the ADD time allowances for the following labor operations have been
revised. The warranty chart below updates the ADD conditions for the following labor operation numbers. These times are effective immediately.

Warranty Information

For vehicles repaired under warranty, use the table.


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 493
Chevrolet Venture V6-3.4L VIN E 2818

Disclaimer
Technical Service Bulletin # 08-09-41-003 Date: 080225

Restraints - Usage of Used/Salvaged/Imitation Components


INFORMATION

Bulletin No.: 08-09-41-003

Date: February 25, 2008

Subject:
General Motors Position Statement on Installation of Used Salvaged or Imitation Air Bag System Components

Models:
2008 and Prior GM Cars and Light Duty Trucks (Including Saturn and Saab)
2008 and Prior HUMMER H2, H3

Due to the critical nature of the design of Supplemental Inflatable Restraint Systems (SIR) (also known as air bag systems) GM does not support
the use of any used salvage or imitation parts for repair. Only new genuine GM warranted parts should be used in repair.

Proper operation of the air bag system requires that any repairs to the vehicle be made with new GM warranted parts. Never use air bag parts from
another vehicle or source. The reasons for this policy and practice within GM include the following:

Occupant Protection

Air bag system components are carefully developed and specifically tuned for the specific vehicle environment. Corresponding air bag system
components from other models or other model years may appear similar from the outside and may even fit the vehicle but different internal
elements or calibrations may result in degraded restraint performance.

Regulatory Compliance

All new GM vehicles are designed and built to meet or exceed all applicable Canadian and U.S. Federal Motor Vehicle Safety Standards. Use of air
bag system components other than those specified could result in degraded restraint performance and under some circumstances could render the
system inoperative. A repair establishment that knowingly makes a regulated safety system inoperative violates the Safety Act and becomes liable
accordingly. The repair establishment also risks liability for losses or damage resulting from the repair.

Reliability

Reuse of used or salvaged components brings into question the conditions under which the components were obtained and stored prior to use.

Components could have been damaged or stored under unfavorable conditions that could compromise performance and reliability.

Warranty

The use of new parts is consistent with the vehicle factory warranty and extended warranty programs.

In summary new GM parts remain General Motors recommendation for repairs involving air bags systems and components. Air bag systems can
best be returned to appropriate levels of performance when new GM parts are used.

(This information is also available online at: www.techinfo.gmgoodwrench.com.)

Disclaimer
Technical Service Bulletin # 03-06-01-010C Date: 080408

Engine/Cooling System - Oil or Coolant Leaks


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 494
Chevrolet Venture V6-3.4L VIN E 2819
TECHNICAL

Bulletin No.: 03-06-01-010C

Date: April 08, 2008

Subject:
Engine Oil or Coolant Leak (Install New Lower Intake Manifold Gasket)

Models:
2000-2003 Buick Century
2002-2003 Buick Rendezvous
1996 Chevrolet Lumina APV
1997-2003 Chevrolet Venture
1999-2001 Chevrolet Lumina
1999-2003 Chevrolet Malibu, Monte Carlo
2000-2003 Chevrolet Impala
1996-2003 Oldsmobile Silhouette
1999 Oldsmobile Cutlass
1999-2003 Oldsmobile Alero
1996-1999 Pontiac Trans Sport
1999-2003 Pontiac Grand Am, Montana
2000-2003 Pontiac Grand Prix
2001-2003 Pontiac Aztek

with 3.1L or 3.4L V-6 Engine (VINs J, E - RPOs LG8, LA1)

Supercede:

This bulletin is being revised to update the Parts Information and add an Important statement. Please discard Corporate Bulletin Number
03-06-01-010B (Section 06 - Engine).

Condition

Some owners may comment on an apparent oil or coolant leak. Additionally the comments may range from spots on the driveway to having to add
fluids.

Cause

Lower Intake manifold may be leaking allowing coolant oil or both to leak from the engine.

Correction

Install a new design lower intake manifold gasket. The material used in the gasket has been changed in order to improve the sealing qualities of the
gasket. When replacing the gasket the lower intake manifold bolts must also be replaced and torqued in sequence to a specification.

Important:
The gasket kit part number listed below now includes the new bolts (4 long bolts and 4 short bolts) with the pre-applied threadlocker on
them. It is no longer necessary to order the bolts separately when ordering gaskets.

Notice:
An oil leak may result if the vertical bolts are not tightened before the diagonal bolts.

Diagonal bolts may require a crows foot to tighten.

Tighten
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 495
Chevrolet Venture V6-3.4L VIN E 2820

1. Tighten the vertical lower intake manifold bolts (1) to 7 N.m (62 lb in).

2. Tighten the diagonal lower intake manifold bolts (2) to 7 N.m (62 lb in).

3. Tighten the vertical lower intake manifold bolts (1)to 13 N.m (115 lb in).

4. Tighten the diagonal lower intake manifold bolts (2) to 25 N.m (18 lb ft).

Parts Information

Warranty Information

For vehicles repaired under warranty, use the table.

Disclaimer
Technical Service Bulletin # 05-00-89-078B Date: 080206

Fuel System - GM Fuel System Treatment PLUS(R) Info.


Bulletin No.: 05-00-89-078B

Date: February 06, 2008

INFORMATION

Subject:
GM Fuel System Treatment PLUS Fuel Sending Unit Corrosion and Fuel System Deposits

Models:
2008 and Prior GM Passenger Cars and Trucks (including Saturn)
2008 and Prior HUMMER H2, H3
2005-2008 Saab 9-7X

Supercede:

This bulletin is being revised to add model years. Please discard Corporate Bulletin Number 05-00-89-078A (Section 00 - General Information).

The GM Fuel System Treatment PLUS is not recommended for use with diesel fuel. The GM Fuel System Treatment PLUS is specially formulated
for use in gasoline and/or E85 fuels.

GM Fuel System Treatment PLUS

GM Fuel System Treatment PLUS P/N 88861011 (for U.S. ACDelco(R) use 88861013) (in Canada 88861012) is now available for use in gasoline
engines.

Added Benefits and Uses

The PLUS portion of GM Fuel System Treatment PLUS is the addition of a filmer additive that when used regularly can protect fuel system
sending units from the corrosive effects of certain sulfur contaminants found in some of todays gasoline.

Sulfur contamination can disrupt electrical continuity of certain fuel sending units and lead to erratic or false fuel gauge readings. With scheduled
usage GM Fuel System Treatment PLUS protects against the effects of harmful sulfurs in gasoline.

The Four Benefits


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 496
Chevrolet Venture V6-3.4L VIN E 2821

Just pour in one bottle of the GM Fuel System Treatment PLUS into the fuel tank when refueling around each oil change interval:

Cleans - Sulfur corrosion from fuel gauge sending units.

Prevents - Harmful sulfur components from attacking sensitive fuel system electronics.

Protects - By coating metallic surfaces of the fuel system.

Removes - Engine deposits left from use of poor quality fuels.

Parts Information

Disclaimer
Technical Service Bulletin # 06-06-04-035A Date: 080205

Fuel System - E85 Fuel Usage Precaution


Bulletin No.: 06-06-04-035A

Date: February 05, 2008

INFORMATION

Subject:
Use of E85 Fuels in Vehicles Not Certified by GM as being FlexFuel Compatible / Aftermarket Conversion of Vehicles to Operate on E85 Fuels

Models:
2008 and Prior GM Passenger Cars and Trucks NOT FlexFuel (E85) Compatible (including Saturn)
2008 and Prior HUMMER H2, H3
2005-2008 Saab 9-7X

Supercede:

This bulletin is being revised to add model years. Please discard Corporate Bulletin Number 06-06-04-035 (Section 06 - Engine/Propulsion
System).

Aftermarket Conversions of Vehicles to Use E85 Fuels

General Motors has become aware of several companies that claim to be able to convert vehicles equipped with gasoline engines to be compatible
with E85 Fuels.

Vehicles certified by GM as being FlexFuel (E85) compatible contain numerous calibration and component differences that are not conducive to an
aftermarket retrofit.

General Motors DOES NOT support or endorse conversions that may alter the emissions and related emissions components of its vehicles.

Repairs that may result from changes to GM built components and repairs that result from the use of improper fuel such as the use of gasoline
containing more than 10% Ethanol in a non-FlexFuel certified vehicle are not covered under the terms of the New Vehicle Warranty.

E85 Compatible Vehicles


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 497
Chevrolet Venture V6-3.4L VIN E 2822

The only E85 compatible vehicles produced by General Motors are shown above.

Disclaimer
Technical Service Bulletin # 99-08-52-005C Date: 080130

Keyless Entry System - Characteristics of Operation


Bulletin No.: 99-08-52-005C

Date: January 30, 2008

INFORMATION

Subject:
Remote Keyless Entry Operational Characteristics

Models:
1997-2008 All Passenger Cars and Trucks
2003-2008 HUMMER H2
2006-2008 HUMMER H3
2005-2008 Saab 9-7X

with Remote Keyless Entry

Supercede:

This bulletin is being revised to add model years and additional information. Please discard Corporate Bulletin Number 99-08-52-005B (Section 08
- Body and Accessories).

The following information regarding Remote Keyless Entry (RKE) operation may be given to customers as needed.

The General Motors RKE systems operate on high frequency radio signals. Therefore they may be subject to radio signal interference which will
affect RKE operation. Some of the typical conditions which result in reduced RKE transmitter operation are listed below.

To prevent battery drain, RKE transmitter will lock up if any button or buttons are depressed longer than 30 seconds. The transmitter will unlock if
another button is depressed. While programming the transmitter in the relearn mode, use the J 43241 tester, to confirm that the signals are being
transmitted to the RCDLR. If the RKE locks up during the programming, depress another button to unlock the RKE.

Note
Always refer to SI for latest diagnostic information
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 498
Chevrolet Venture V6-3.4L VIN E 2823

If on the second press of the unlock button all doors are not unlocked it may be due to the time delay needed by the system to recognize the second
press of the unlock button. In order to unlock all doors press the unlock button once pause 1-2 seconds and press the unlock button the second time.

There needs to be a pause between button presses so that the receiver can properly process the signal from the transmitter.

For many 2006 and later car lines the trunk release button requires a press and hold before the trunk lid will release.

Line of sight. The transmitter signal may be obstructed by obstacles; another vehicle building or other obstructions in the line of sight.

Proximity to radio towers airports police and fire towers.

The presence of fluorescent lighting.

Installation of some aftermarket accessories have been known to affect the RKE performance as well.

Some brands of radar detectors CB radios walkie talkies mobile radios cell phone chargers and cell phones (especially 3-watt bag phones which are
placed on the floor of the vehicle) have jammed the radio frequencies of the RKE system.

Remember these devices do not have to be in the customers vehicle. They may be in another vehicle which is in close proximity. However if the
customer has one of these devices in their vehicle and if the RKE system works with these aftermarket devices unplugged refer the customer to the
aftermarket supplier. The aftermarket device may not meet the requirements of the FCC Code.

If the customer comments that the remote transmitter fails to operate press each button on the transmitter one at a time while observing the vehicle
systems.

If only the fuel door (Cadillac) or panic button (all other vehicles) works or the transmitter fails to operated re-synchronize the system following the
transmitter synchronization procedure found in the Keyless Entry sub-section of Body & Accessories in the Service Manual. If the RKE system is
auto-synchronized reprogram the transmitter following the procedures in the Keyless Entry sub-section of SI.

DO NOT REPLACE ANY COMPONENTS.

Re-synchronization must be performed if the following conditions exist:

The batteries of the keyless entry transmitter have been replaced. A keyless entry transmitter is malfunctioning.

If all of the transmitter buttons fail to function check the battery and transmitter using tester J 43241. Refer to Corporate Bulletin Number 83-90-12.

If the transmitter passes the test program the RKE system following the procedures in the Keyless Entry sub-section of Body & Accessories in the
Service Manual.

Remember when programming the system, all transmitters for the vehicle must be present for the programming to be successful.

On many 2006 vehicle lines RKE transmitter commands can be viewed using a scan tool (under RCDLR Data Displays).

If the transmitter fails the test with the tester J 43241 replace the batteries and retest the transmitter using the tester J 43241. If the transmitter still
fails the test replace the transmitter.

THE FOLLOWING CLAIM TYPES ARE NOT COVERED UNDER THE VEHICLE WARRANTY:

The battery is considered a consumable battery and is covered for the first 12 months only. Refer to "Maintenance" in the In-Vehicle Warranty
Booklet. Battery life is determined by the number of times a pad on the transmitter has been used, not by time or mileage and as such, battery
replacement would be considered owner maintenance (i.e. batteries in a flash light, engine oil changes).

Transmitter replacement when all buttons work, using the tester J 43241 as outlined in Corporate Bulletin Number 83-90-12.

Personalization programming through the DIC or Tech 2(R).

Lost/replacement transmitter reprogramming.

Used car transmitter replacement programming.

Transmitter damage due to misuse, such as any liquid spilled on/in the transmitter or damage from animals chewing on the transmitter, etc.

Broken transmitter cases where the key ring attaches to the case. If the case is broken in this area, it is due to mounting the transmitter direct to the
key ring without the protection of the small ring. The small ring acts like a universal joint/flex joint and helps protect the transmitter from this type
of damage. Refer to Corporate Bulletin Number 03-08-52-003 for EXCEPTIONS to this rule.

Garage door opener programming.


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 499
Chevrolet Venture V6-3.4L VIN E 2824

Disclaimer
Technical Service Bulletin # 08-08-51-002 Date: 080312

Body - TPO Fascia Cleaning Prior to Painting


INFORMATION

Bulletin No.: 08-08-51-002

Date: March 12, 2008

Subject:
New Primer For TPO Fascias and Affected Cleaning Process of Painting Operation

Models:
2009 and Prior Passenger Cars and Trucks
2009 and Prior HUMMER H2, H3

The purpose of this bulletin is to inform the technician that General Motors has made a change in the primer it uses for TPO plastic for service
parts. This new primer comes in several different colors from five different suppliers. This change affects the cleaning process of the painting
operation. The new process is as follows.

1. Wash with soap and water.

2. Clean with a 50% mix of isopropyl alcohol and water (or a waterborne cleaner). Check with your paint supplier for product
recommendations.

3. Scuff sand per your paint suppliers recommendations.

Note:
The use of a solvent-type cleaner will soften, or begin to dissolve the primer. Base coats do not have any affect on this primer.

4. Reclean with a 50% mix of isopropyl alcohol and water (or a waterborne cleaner).

All fascias, with the exception of the Corvette, Camaro, and Cadillac XLR, are made of TPO. You may find other TPO parts with this primer.
If the technician has a question as to the type of plastic they are painting, inspect the back of the part for the plastic symbol (TPO).

DisclaimerTechnical Service Bulletin # 08-01-38-001 Date: 080125

A/C - Refrigerant Recovery/Recycling/Equipment


Bulletin No.: 08-01-38-001

Date: January 25, 2008

INFORMATION

Subject:
Information On New GE-48800 CoolTech Refrigerant Recovery/Recharge Equipment

Models:
2008 and Prior GM Passenger Cars and Light Duty Trucks (Including Saturn)
2008 and Prior HUMMER H2, H3
2005-2008 Saab 9-7X
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 500
Chevrolet Venture V6-3.4L VIN E 2825

Attention:
This bulletin is being issued to announce the release of GM approved Air Conditioning (A/C) Refrigerant Recovery and Recharging Equipment
that meets the new Society of Automotive Engineers (SAE) J2788 Refrigerant Recovery Standards. The ACR2000 (J-43600) cannot be
manufactured in its current state after December 2007 and will be superseded by GE-48800.

The new J2788 standard does not require that GM Dealers replace their ACR2000 units. ACR2000's currently in use are very capable of servicing
today's refrigerant systems when used correctly and can continue to be used. Details regarding the new SAE J2788 standard are outlined in GM
Bulletin 07-01-38-004.

Effective February 1 2008, new A/C Refrigerant Recovery/Recharging equipment (P/N GE-48800) will be released as a required replacement for
the previously essential ACR2000 (J-43600). This equipment is SAE J2788 compliant and meets GM requirements for A/C Refrigerant System
Repairs on all General Motors vehicles, including Hybrid systems with Polyolester (POE) refrigerant oil. This equipment will not be shipped as an
essential tool to GM Dealerships.

In addition, this equipment is Hybrid compliant and designed to prevent oil cross contamination when servicing Hybrid vehicles with Electric A/C
Compressors that use POE refrigerant oil.

The ACR2000 (J-43600) will need to be retrofitted with a J-43600-50 (Hose - ACR2000 Oil Flush Loop) to be able to perform Hybrid A/C service
work. All Hybrid dealers will receive the J-43600-50, with installation instructions, as a component of the Hybrid essential tool package.
Dealerships that do not sell Hybrids, but may need to service Hybrids, can obtain J-43600-50 from SPX Kent Moore. Refer to GM Bulletin
08-01-39-001 for the ACR2000 Hose Flush procedure.

The High Voltage (HV) electric A/C compressor used on Two Mode Hybrid vehicles uses a Polyolester (POE) refrigerant oil instead of a
Polyalkylene Glycol (PAG) synthetic refrigerant oil. This is due to the better electrical resistance of the POE oil and its ability to provide HV
isolation.

Failure to flush the hoses before adding refrigerant to a Hybrid vehicle with an electric A/C compressor may result in an unacceptable amount of
PAG oil entering the refrigerant system. It may cause a Battery Energy Control Module Hybrid Battery Voltage System Isolation Lost Diagnostic
Trouble Code (DTC P1AE7) to be set. Additionally, the A/C system warranty will be voided.

Warranty Submission Requirements

The Electronically Generated Repair Data (snapshot summary) and printer functions have been eliminated from the GE-48800. The VGA display
and temperature probes were eliminated to reduce equipment costs. As a result, effective immediately the 18 digit "Snapshot/Charge Summary"
code is no longer required for Air Conditioning (A/C) refrigerant system repairs that are submitted for warranty reimbursement. The charge
summary data from before and after system repairs will continue to required, but documented on the repair order only. Both high and low pressures
and the recovery and charge amounts should be noted during the repair and entered on the repair order. If using ACR2000 (J-43600), the
"Snapshot/Charge Summary" printouts should continue to be attached to the shops copy of the repair order.

The labor codes that are affected by this requirement are D3000 through D4500.

Disclaimer
Technical Service Bulletin # 01-07-30-010C Date: 080512

A/T - Torque Converter Replacement Information


INFORMATION

Bulletin No.: 01-07-30-010C

Date: May 12, 2008

Subject:
Automatic Transmission/Transaxle Torque Converter Replacement

Models:
2009 and Prior GM Passenger Cars and Trucks
2009 and Prior HUMMER H2, H3
2009 and Prior Saturn Cars and Light Duty Trucks (Except VTi Equipped Vehicles (RPO M16 and M75)
2009 and Prior Saab 9-7X

with ALL Automatic Transmissions and Transaxles


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 501
Chevrolet Venture V6-3.4L VIN E 2826

Supercede:

This bulletin is being revised to add the 2007-2009 model years. Please discard Corporate Bulletin Number 01-07-30-010B (Section 07 -
Transmission/Transaxle).

The purpose of this bulletin is to help technicians determine when a torque converter should be replaced. Below is a list of general guidelines to
follow.

The converter should NOT be replaced if the following apply:

^ DTC P0742 - TCC stuck on is set. This code is almost always the result of a controls condition (i.e. stuck TCC solenoid/valve). Experience has
shown that this code rarely indicates a mechanical concern within the torque converter.

^ The fluid has an odor or is discolored but no evidence of metal contamination.

^ Fine metal particles (traces of metal flakes/gray color to fluid ) are found in the converter. This is not harmful to the torque converter.

^ The vehicle has been exposed to high mileage.

^ A small amount of wear appears on the hub where the oil pump drive gear mates to the converter (RWD only). A certain amount of such wear
is normal for both the hub and oil pump gear. Neither the converter nor the front pump assembly should be replaced.

The torque converter should be replaced under any of the following conditions:

^ The vehicle has TCC shudder and/or no TCC apply. First complete all electrical and hydraulic diagnosis and check for proper engine operation.
The converter clutch may be damaged. Also the converter bushing and/or internal 0-ring may be damaged.

^ Evidence of damage to the oil pump assembly pump shaft turbine shaft drive sprocket support and bearing or metal chips/debris in the
converter.

^ Metal chips/debris are found in the converter or when flushing the cooler and the cooler lines.

^ External leaks in the hub weld area lug weld or closure weld.

^ Converter pilot is broken damaged or fits poorly into the crankshaft.

^ The converter hub is scored or damaged.

^ The transmission oil is contaminated with engine coolant engine oil or water.

^ If excessive end play is found after measuring the converter for proper end play (refer to Service Manual).

^ If metal chips/debris are found in the fluid filter or on the magnet and no internal parts in the unit are worn or damaged. This indicates that the
material came from the converter.

^ The converter has an unbalanced condition that results in a vibration that cannot be corrected by following Converter Vibration Procedures.

^ Blue converter or dark circular ring between lugs. This condition will also require a complete cleaning of the cooler and a check for adequate
flow through the cooler.

^ Converter bearing noise determined by noise from the bell housing area in Drive or Reverse at idle. The noise is gone in Neutral and Park.

^ If silicon from the viscous clutch is found in the lower pan (4T80-E ONLY).

Disclaimer
Technical Service Bulletin # 04-06-04-036E Date: 080508

Emission - Emissions Programming Warranty Coverage


WARRANTY ADMINISTRATION

Bulletin No.: 04-06-04-036E


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 502
Chevrolet Venture V6-3.4L VIN E 2827

Date: May 08, 2008

Subject:
Warranty Coverage for Emission-Related Reprogramming Events (PCM, ECM and TCM)

Models:
2009 and Prior GM Passenger Cars and Trucks (Including Saturn)
2003-2009 HUMMER H2
2006-2009 HUMMER H3
2009 and Prior Saab Vehicles (Canada Only)

Attention:
This bulletin applies only to dealers in the United States and Canada. Export dealers are not authorized to utilize this service bulletin.

Supercede:

This bulletin is being updated to add an Attention statement. Please discard Corporate Bulletin Number 04-06-04-036D (Section 06 - Engine).

The coverage for emission-related reprogramming has the same coverage as the emission controller under the emission controller warranty - 8
years/80,000 miles (130,000 km).

Reprogramming that is not emissions-related is covered under the terms of the Bumper to Bumper Limited Warranty. (For additional information
regarding labor codes for use in non-emission-related reprogramming refer to Corporate Bulletin Number 06-08-47-001D.)

Emissions-related calibration updates will be announced through a GM Technical Service Bulletin with specific guidelines of coverage for each
model affected. A special emission-related reprogramming labor operation will be used. The labor operation to be used for claims relating to
emission-related reprogramming is J6353 and will only be referenced in the bulletins addressing emission-related calibrations. This labor operation
must NOT be used for non-emissions-related reprogramming or for any other vehicle that is not referenced in an emission-related reprogramming
technical service bulletin.

Example:

The PCM on 2004 model light duty vehicles is covered by the emission controller warranty for 8 years/80,000 miles (130,000 km). If GM released
an "emission-related" calibration update for one of these vehicles, this reprogramming event would also be covered for the remainder of the 8
years/80,000 miles (130,000 km). If GM released a driveability-related calibration update (for example to eliminate a hesitation) for one of these
vehicles, this reprogramming event would be covered for the remainder of the terms of the Bumper to Bumper Limited Warranty.

An emission-related calibration for medium duty and diesel applications are also covered by the emission warranty that is applicable to that
vehicle's emissions controller.

Example:

The PCM on 2004 model medium duty vehicles is covered by the emission controller warranty for 5 years/50,000 miles (80,000 km). If GM
released an "emission-related" calibration update for one of these vehicles, this reprogramming event would also be covered for 5 years/50,000
miles (80,000 km).

DisclaimerTechnical Service Bulletin # 08-07-30-027 Date: 080604

A/T - No Movement in Drive or 3rd Gear


TECHNICAL

Bulletin No.: 08-07-30-027

Date: June 04, 2008

Subject:
No Movement When Transmission is Shifted to Drive or Third - Normal Operation When Shifted to Second, First or Reverse (Replace Forward
Sprag Assembly)

Models:
1982 - 2005 GM Passenger Cars and Light Duty Trucks
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 503
Chevrolet Venture V6-3.4L VIN E 2828
2006 - 2007 Buick Rainier
2006 Cadillac Escalade, Escalade ESV, Escalade EXT
2006 Chevrolet SSR
2006 - 2008 Chevrolet Avalanche, Colorado, Express, Silverado Classic, Silverado, Suburban, Tahoe, TrailBlazer
2006 GMC Yukon Denali, Yukon Denali XL
2006 - 2008 GMC Canyon, Envoy, Savana, Sierra Classic, Sierra, Yukon, Yukon XL
2006 Pontiac GTO
2006 - 2007 HUMMER H2
2006 - 2008 HUMMER H3
2006 - 2008 Saab 9-7X

with 4L60, 4L60E, 4L65E or 4L70E Automatic Transmission (RPOs MD8, M30, M32, M33 or M70)

Condition

Some customers may comment that the vehicle has no movement when the transmission is shifted to DRIVE or THIRD position, but there is
normal operation when it is shifted to SECOND, FIRST or REVERSE position.

Cause

This condition may be caused by a damaged forward sprag assembly (642).

Correction

When inspecting the sprag, it is important to test the sprag for proper operation by holding the outer race (644) with one hand while rotating the
input sun gear (640) with the other hand. The sun gear should rotate only in the counterclockwise direction with the input sun gear facing upward.
If the sprag rotates in both directions or will not rotate in either direction, the sprag elements should be inspected by removing one of the sprag
assembly retaining rings (643). Refer to SI Unit Repair section for forward clutch sprag disassembly procedures.

If the sprag is found to be damaged, make repairs to the transmission as necessary. A new forward roller clutch sprag assembly is now available
from GMSPO.

If clutch debris is found, it is also very important to inspect the Pressure Control (PC) solenoid valve (377) fluid screens. Clean or replace the PC
solenoid (377) as necessary. It is also important to flush and flow check the transmission oil cooler using J45096. Refer to SI Automatic
Transmission Oil Cooler Flushing and Flow Test for the procedure.
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 504
Chevrolet Venture V6-3.4L VIN E 2829

The notches above each sprag must point up as shown when assembled into the outer race.

Bearing Assembly, Input Sun Gear

Snap Ring, Overrun Clutch Hub Retaining

Hub, Overrun Clutch

Wear Plate, Sprag Assembly

Retainer and Race Assembly, Sprag

Forward Sprag Assembly

Retainer Rings, Sprag Assembly

Outer Race, Forward Clutch

Washer, Thrust (Input Carrier to Race)

The following information applies when this sprag is used in 1982-86 transmissions.

The new design sprag can be used on models 1982 through 1986, by replacing the entire assembly (637 - 644). Individual components are NOT
interchangeable.

Important:
The wear plate (640) and input thrust washer (660) are not required with the new sprag. Use of the thrust washer and wear plate with the new
sprag assembly will cause a misbuild (correct end play cannot be obtained).

Parts Information

Warranty Information

For vehicles repaired under warranty, use the table.

DisclaimerTechnical Service Bulletin # 99-07-30-030F Date: 080501

A/T - Grinding/Growling Noise in Park on Incline


INFORMATION

Bulletin No.: 99-07-30-030F


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 505
Chevrolet Venture V6-3.4L VIN E 2830

Date: May 01, 2008

Subject:
Grinding and/or Growling Noise in Park on Incline

Models:
2009 and Prior Passenger Cars and Light Duty Trucks (Including Saturn)

with Hydra-Matic Front Wheel Drive (FWD) Automatic Transmissions

Supercede:

This bulletin is being revised to add model years. Please discard Corporate Bulletin Number 99-07-30-030E (Section 07 - Transmission/Transaxle).

Service Information

Owners of some vehicles equipped with Hydra-Matic front wheel drive transaxles may comment on a grinding and/or growling noise that is
noticeable when standing in PARK on a hill or slope with the engine running and the parking brake not applied. Under these conditions, the weight
of the vehicle puts a load on the parking pawl which can create a "ground-out" path through the drive axles, front struts, springs and spring towers.
Normal engine noise can be transmitted to the passenger compartment through the "ground-out" path.

Owners concerned about this condition should be advised to apply the parking brake prior to shifting into PARK. This is the recommended
procedure described in the Owners Manual. Applying the parking brake first will put the load of the vehicle on the rear brakes rather than on the
parking pawl.

Refer the owner to the appropriate Owner Manual for additional details and instructions.

Disclaimer
Technical Service Bulletin # 08-07-30-026 Date: 080522

A/T - Slight Vehicle Movement In Park At Start Up


INFORMATION

Bulletin No.: 08-07-30-026

Date: May 22, 2008

Subject:
Information on Slight Vehicle Movement In Park At Start Up After Cold Soak

Models:
2009 and Prior GM Passenger Cars and Light Duty Trucks (including Saturn)
2009 and Prior HUMMER H2, H3
2009 and Prior Saab 9-7X

with Automatic Transmission

Some vehicles may rock or move slightly forward or rearward while in park at start up after cold soak. This condition may be accompanied by a
clunk noise. This is a slight movement that is more often seen visually, rather than felt, when viewed from the outside and using the auto-start
feature, if equipped.

This slight movement is due to the residual transmission fluid in the clutch packs that creates a partial apply on start up. This movement is stopped
by the parking pawl and/or transmission fluid exhausting completely from the clutch packs.

This slight movement has no adverse affects on the transmission and no repair should be attempted. This condition is normal. This can be verified
by comparing with another identically built vehicle under the same cold conditions.

To prevent this condition from occurring, the parking brake should be utilized as per the Owners Manual recommendations anytime the vehicle is
parked.
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 506
Chevrolet Venture V6-3.4L VIN E 2831

Disclaimer
Technical Service Bulletin # 00-07-30-022D Date: 080610

A/T - 4L60/65E, No Reverse/2nd or 4th Gear


TECHNICAL

Bulletin No.: 00-07-30-022D

Date: June 10, 2008

Subject:
No Reverse, Second Gear or Fourth Gear (Replace Reaction Sun Shell with More Robust Heat Treated Parts)

Models:
1993 - 2005 GM Passenger Cars and Light Duty Trucks
2003 - 2005 HUMMER H2

with 4L60/65-E Automatic Transmission (RPOs M30 or M32)

Supercede:
This bulletin is being revised to add 2005 model year to the parts information. Please discard Corporate Bulletin Number 00-07-30-022C (Section
07 - Transmission/Transaxle).

Condition

Some customers may comment on a no reverse, no second or no fourth gear condition. First and third gears will operate properly.

Cause

The reaction sun gear (673) may not hold inside the reaction sun shell (670).

Correction

Important:
There are FOUR distinct groups of vehicles and repair procedures involved. Vehicles built in the 2001 model year and prior that make use of a
reaction shaft to shell thrust washer:

^ The sun shell can be identified by four square holes used to retain the thrust washer. Use reaction sun shell P/N 24228345, reaction carrier
to shell thrust washer (699B) P/N 8642202 and reaction sun gear shell thrust washer (674) P/N 8642331er (674) P/N 8642331along with the
appropriate seals and washers listed below.

^ Vehicles built in the 2001 model year and prior that have had previous service to the reaction sun shell: It is possible that some 2001 and
prior model year vehicles have had previous service to the reaction sun shell. At the time of service, these vehicles may have been updated
with a Reaction Sun Shell Kit (Refer to Service Bulletin 020730003) without four square holes to retain the thrust washer. If it is found in a
2001 model year and prior vehicles that the reaction sun shell DOES NOT have four square holes to retain the thrust washer, these vehicles
must be serviced with P/Ns 24229825 (674), 24217328 and 8642331 along with the appropriate seals and washers listed below.

^ Vehicles built in the 2001 model year and later that make use of a reaction shaft to shell thrust bearing: The sun shell can be identified by no
holes to retain the thrust washer. Use reaction sun shell, P/N 24229825, reaction carrier shaft to shell thrust bearing (669A), P/N 24217328
and reaction sun gear shell thrust washer (674), P/N 8642331 along with the appropriate seals and washers listed below.

^ Vehicles built from November, 2001 through June, 2002: These vehicles should have the reaction carrier shaft replaced when the sun shell
is replaced. Use shell kit P/N 24229853, which contains a sun shell (670), a reaction carrier shaft (666), a reaction carrier shaft to shell
thrust bearing (669A) and a reaction sun gear shell thrust washer (674). The appropriate seals and washers listed below should also be used.

When servicing the transmission as a result of this condition, the transmission oil cooler and lines MUST be flushed. Refer to Corporate Bulletin
Number 02-07-30-052.

Follow the service procedure below for diagnosis and correction of the no reverse, no second, no forth condition.

Important:
If metallic debris is found on the transmission magnet, the transmission must be completely disassembled and cleaned. Metallic debris is
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 507
Chevrolet Venture V6-3.4L VIN E 2832
defined as broken parts and pieces of internal transmission components. This should not be confused with typical "normal" fine particles
found on all transmission magnets. Failure to properly clean the transmission case and internal components may lead to additional repeat
repairs.

1. Remove the transmission oil pan and inspect the magnet in the bottom of the pan for metal debris. Refer to SI Document ID # 825141.

2. Remove the transmission from the vehicle. Refer to the appropriate SI document.

Important:
^ Inspect all the transmission components for damage or wear. Replace all damaged or worn components. The parts shown above
should be sufficient to correct this concern.

^ This condition does not normally require replacement of the transmission completely. Components such as clutches, valve body,
pump and torque converters will NOT require replacement to correct this condition.

Disassemble the transmission and replace the appropriate parts listed below. Refer to the Unit Repair Manual - Repair Instructions.

3. Reinstall the transmission in the vehicle. Refer to appropriate service information.

When servicing the transmission as a result of this condition, the transmission oil cooler and lines MUST be flushed. Refer to Corporate
Bulletin Number 02-07-30-052.
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 508
Chevrolet Venture V6-3.4L VIN E 2833

Parts Information

Warranty Information

For vehicles repaired under warranty, use the table.

DisclaimerTechnical Service Bulletin # 03-07-30-007E Date: 080505

A/T - Gear Engagement Time Information


INFORMATION

Bulletin No.: 03-07-30-007E

Date: May 05, 2008

Subject:
Engagement Time of Electronically Controlled Transmissions in General Motors Vehicles (Garage Shifts, Park to Reverse, Neutral to Drive,
Neutral to Reverse, Park to Drive, Delayed Engagement)
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 509
Chevrolet Venture V6-3.4L VIN E 2834

Models:
2000 - 2002 Chevrolet Camaro
2000 - 2005 Chevrolet Corvette
2000 - 2002 Pontiac Firebird
2004 - 2006 Pontiac GTO
2000 - 2008 All GM Light Duty Trucks
2003 - 2008 HUMMER H2
2006 - 2008 HUMMER H3
2005 - 2008 Saab 9-7X

with 4L60-E (RPO M30) or 4L65-E (RPO M32) Automatic Transmission

Supercede:
This bulletin is being revised to add the 2008 model year to the trucks. Please discard Corporate Bulletin Number 03-07-30-007D (Section 07 -
Transmission/Transaxle).

Park/Neutral to Reverse or Drive (commonly called garage shift) engagement times may be different from what many customers might be
accustomed to especially if they have recently traded for a General Motors vehicle.

Normal Park/Neutral to Reverse or Drive engagement time will be in the vicinity of one (1) second if the automatic transmission fluid (ATF) is
above 0°C (32°F). When the ATF is colder than 0°C (32°F), the engagement time will become longer the colder the transmission fluid. A time limit
factor cannot be placed on proper engagement times because the factors that affect transmission operation are many.

At the moment of engine start, for economy and emission requirements, the transmission line pressure is maintained at low levels. This allows a
lower cold idle engine RPM (the colder the oil is, the higher the energy level (engine torque output) required to pressurize the oil).

When the driver moves the shift lever from "Park/Neutral" to "Reverse" or any "Drive" range, the following actions must occur for the powertrain
control module (PCM) to determine at what pressure to control the transmission line pressure.

The module will look at the following items:

1. The voltage readings of the engine coolant temperature sensor (ECT).

2. The voltage reading of the transmission fluid temperature sensor (TFT).

3. Whether or not air conditioning is requested.

4. Movement of the shift lever and controls engine RPM based on the gear position selected. The module will adjust the engine RPM in
response to the torque requirements needed to increase transmission line pressure.

When the module determines the status of the above items, the module will apply the appropriate signal to the PWM pressure control
solenoid, thereby controlling the application of the required clutch(es) depending on the driver's selection.

Controlling transmission apply pressures allows the transmission to engage in a smooth manner, thus reducing the potential of abrupt/harsh
engagement of the transmission.

All of the above actions happen very quickly; however, the resultant time interval may be approximately one second.

When determining if shift times are excessive, the exact conditions that the vehicle was in at the time the extended garage shift occurred must
be duplicated. The following are several possible conditions.

^ Was the vehicle outside or in a heated garage?

^ What was the temperature of the environment at the time of the occurrence?

^ Length of time the vehicle sat unused, such as overnight or a weekend, etc.? A vehicle that has been driven to the service facility cannot
be tested for this concern because the transmission, the engine oil and the coolant are no longer at the temperature they were when the
customer experienced the condition.

No attempts to repair should occur unless the condition can be duplicated under the conditions the customer experienced.

Road test the vehicle following the steps below until the vehicle engine and transmission temperatures are at normal operating temperatures. This is
approximately 16 km (10 mi) of driving.

1. In a safe manner, bring the vehicle to a complete stop.

2. Place the shift lever in Neutral and wait five seconds.

3. Place the shift lever in Drive. A delayed engagement of approximately one (1) second will occur. THIS IS NORMAL. This time may be
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 510
Chevrolet Venture V6-3.4L VIN E 2835
extended if the engine RPM is above the base idle, controlled by the driver's foot rather than the control module.

4. Drive the vehicle for a distance of not less than a tenth of a mile (160 m).

5. In a safe manner, bring the vehicle to a complete stop.

6. Place the shift lever in Neutral and wait five seconds.

7. Place the shift lever in Reverse. A delayed engagement of approximately one (1) second will occur. THIS IS NORMAL. This time may be
extended if the engine RPM is above the base idle, controlled by the driver's foot rather than the control module.

8. Place the shift lever in Neutral and wait five seconds.

9. Place the shift lever in Drive. A delayed engagement of approximately one (1) second will occur. THIS IS NORMAL. This time may be
extended if the engine RPM is above the base idle, controlled by the driver's foot rather than the control module.

If an out of line condition (excessively long time, over two seconds, to engage a gear) is observed, the following components within the
transmission should be inspected for the cause of the concern.

^ Forward clutch piston seals (delay to drive)

^ Forward accumulator piston and seal for damage (delay to drive)

^ Low and reverse clutch piston seals (delay to reverse)

^ Reverse input clutch piston seals (delay to reverse)

^ Stator shaft to reverse input drum seals (delay to reverse)

DisclaimerTechnical Service Bulletin # 05-00-89-072B Date: 080617

Engine/Fuel System - Oil/Fuel Additive Information


INFORMATION

Bulletin No.: 05-00-89-072B

Date: June 17, 2008

Subject:
Fuel and Oil Additives - Facts and Myths/Maximizing Fuel Economy

Models:
2009 and Prior GM Passenger Cars and Trucks (including Saturn)
2009 and Prior HUMMER H2, H3
2009 and Prior Saab 9-7X

Attention:
Please direct this bulletin to the Service Manager, the Service Consultants and the Sales Staff. A copy of this bulletin is encouraged to be given
to your customer as it is written with the consumer in mind. You may also post this bulletin in your customer lounge or waiting area.

Supercede:

This bulletin is being revised to add the 2009 model year. Please discard Corporate Bulletin Number 05-00-89-072A (Section 00 - General
information).

A Statement About Fuel Economy

As gasoline prices have increased, the consumer has shifted priorities to become increasingly concerned with fuel consumption. GM is presently
proud to offer over 30 cars in the U.S. with EPA highway estimates of at least 30 mpg. In Canada, vehicles are rated for fuel consumption in liters
per 100 kilometers. GM offers over 20 vehicles in Canada that consume less than 7.0 L/100 km on the highway. The information below contains
reasonable and prudent advice for your dealership and the consumer to get the most from every gallon or liter of gas.
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 511
Chevrolet Venture V6-3.4L VIN E 2836

The information below is presented in two easy to understand sections:

^ What Not To Do: Engine and Fuel Additives, Alternate Fuels, and "Miracle" Products

^ What to Do: Maximizing Fuel Economy/Minimizing Costs

WHAT NOT TO DO: Engine and Fuel Additives, Alternate Fuels, and "Miracle" Products

Various unproven products with claims to improve vehicle fuel economy have been reported ranging from magnets that align molecules to
chemical combustion improvers.

Most products claiming to provide benefits are based on unsubstantiated claims. Those that do present "scientific" results generally either have too
little supporting data to be conclusive, have not conducted experiments in a controlled fashion, or cannot be substantiated by anyone else but the
product's manufacturer.

The U.S. Federal Trade Commission summarizes results for products tested by the federal government at
www.ftc.gov/bcp/edu/pubs/consumer/autos/aut10.shtm. A review of the list shows that the majority did not work, and for those that showed some
effect, the benefit was too small to be cost effective.

Harmful Ideas That May Damage Your Vehicle and Increase Emissions

One more recent poor idea to improve fuel economy that should not be attempted is to blend either kerosene or diesel fuel into gasoline. Why? Both
kerosene and diesel fuel are distillate fuels meant for use in compression ignition engines, not spark ignition engines. They have very low octane
and since they are heavier (higher density) than gasoline, they will cause heavy engine deposits and degradation of engine oil.

Notice:
Never put Kerosene or Diesel Fuel in your Gasoline Engine vehicle. This may result in inconsistent performance and permanent damage to your
vehicle that is not covered by your New Vehicle Warranty.

Chemicals that are normally used as solvents also should not be used. These include acetone, ketones, and methanol. These solvents can be
incompatible with your vehicles rubber or sealing components, and may dissolve the vehicle's paint finish. In the case of methanol, corrosion of
metal parts in the fuel system also may occur.

Notice:
Never use acetone, ketones, or methanol additives in your vehicle. Some of these solvents may damage or corrode your fuel system. They are
also very damaging to the painted surfaces of the vehicle if spilled. Damage to vehicle components that result from non-approved or aftermarket
additives and devices are not covered under the terms of the New Vehicle Warranty. The only fuel additive currently approved by GM is GM
Fuel System Treatment Plus, P/N 88861011 (in Canada, # 88861012).

WHAT TO DO: Maximizing Fuel Economy/Minimizing Costs

The best fuel economy possible is the direct result of proper maintenance and good driving habits. Listed below are GM's recommendations to
achieve the best mileage possible. The first group are things to consider for your vehicle, while the second are tips relating to your driving habits.

Vehicle Considerations:

^ Tire Pressure - One of the major contributors to poor fuel economy are under inflated tires. Tires low on pressure create drag that the vehicle's
powertrain must overcome, wasting dollars in fuel. Always keep your tires inflated to the proper pressure as shown on the vehicle placard. This
not only serves to increase gas mileage but cuts down on tire wear, further decreasing your costs per mile.

^ Air Filter - A vehicle that has a dirty air filter can't efficiently draw air into the engine. This restriction forces the engine to expend energy to
"breathe" wasting fuel in the process. Change recommendations are found in your vehicle Owner's Manual.

^ Proper Viscosity "Starburst" Rated Oil - Always use the proper viscosity oil in your engine. Oil that has a higher than required viscosity will
create more drag on the internal components of the engine, causing more work for it, especially when cold. Each Owner's Manual contains
information on the proper type of oil for your vehicle. Look for the "starburst" symbol on the front of the bottle, and the SM rating on the API
circle on the back label. If you are in doubt, stop by your dealer for an oil change, and any other services required. Most current GM vehicles
are equipped with oil life monitors to further assist on the "when" to change your oil. (Aveo/Wave/Optra/Epica currently do not have oil life
monitors).

Notice:
GM Vehicles DO NOT require additional engine oil additives. Some additives may cause harmful effects to the internal seals and additionally
void the terms of your vehicles New Car Warranty.

^ Top Tier Fuels - Some fuel manufacturers provide gasoline advertised as TOP TIER DETERGENT GASOLINE (Chevron, Conoco, Phillips
66, Shell, Texaco, Entec Stations, MFA Oil Company, 76, Somerset Oil, Aloha Petroleum, Tri-Par Oil Company, QuikTrip, and Kwik Trip) in
the U.S. and (Petro-Canada, Chevron, Shell, and Sunoco) in Canada. These fuels are preferable when and where available. They help to keep
your fuel injectors and intake valves free of deposits. Clean engines provide optimal fuel economy, performance and reduced emissions. When
Top Tier fuels are not available, consider a bottle of GM Fuel System a bottle of GM Fuel System treatment PLUS, P/N# 88861011 (in Canada,
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 512
Chevrolet Venture V6-3.4L VIN E 2837
# 88861012), at oil change time which will remove intake system and injector deposits. GM does not recommend any other fuel system cleaner.

Important:
DO NOT confuse Top Tier Fuels with Higher Octane (Plus/Premium Grade Fuel) commonly sold at most all gas stations. Plus and Premium
fuels are required in some high performance GM vehicles. However, they do not necessarily represent higher detergency present in TOP TIER
Detergent Gasoline.

Important:
For additional information regarding Top Tier fuels and availability, please refer to Corporate Bulletin Number 04-06-04-047G for U.S. or
05-06-04-022D for Canada.

Notice:
E85 FUELS: Only vehicles designated for use with E85 should use E85 blended fuel. E85 compatibility is designated for vehicles that are
certified to run on up to 85% ethanol and 15% gasoline. All other gasoline engines are designed to run on fuel that contains no more than 10%
ethanol. Use of fuel containing greater than 10% ethanol in non-E85 designated vehicles can cause driveability issues, service engine soon
indicators as well as increased fuel system corrosion. See Corporate Bulletin Number 05-06-04-035C for additional information.

^ Use the Recommended Grade (Octane) Fuel

Purchasing higher than required octane fuel is a waste of money. Using higher octane fuels in a vehicle that only required regular unleaded fuel
will neither increase performance nor improve gas mileage. In all cases refer to your owners manual and ONLY use the octane rated fuel
recommended for your vehicle.

Important:
In high performance GM vehicles that DO require Premium (91 octane or higher) fuel, you MUST use fuels of at least this octane. Use of lower
octane fuel may result in reduced performance, knocking, and/or permanent engine damage not covered under the terms of the New Vehicle
Warranty.

^ Check Engine/Service Engine Soon Light - Is the Check Engine/SES light on? When this light is on, the vehicles On-Board diagnostics
computer has noticed that something is wrong. GM vehicles have many sensors that the computer uses to both control and sense actual fuel
usage. When the computer lights the Check Engine/SES light it has lost some ability to run efficiently. This may result in increased fuel
consumption, increased emissions, and/or driveability concerns.

^ Spark Plugs - Even though most current GM vehicles have 160,000 km (100,000 mi) service intervals for spark plugs, if your vehicle is at that
point in its life, have the spark plugs changed to assure proper running and continued efficient, trouble free operation. Refer to the applicable
Maintenance Schedule for spark plugs service intervals on Chevrolet Aveo, Optra, Epica, Pontiac Vibe, Wave and Saturn Astra.

Changes In Driving Habits:

^ Slow Down, Drive Smoothly - Avoid quick/full throttle acceleration from a standstill in town and high cruising speeds on the interstates. While
the optimum MPG for highway cruising speed varies from vehicle to vehicle, faster is almost always worse. If your vehicle is equipped with a
Driver Information Center that displays Instant Fuel Economy, select that read out and vary your cruising speed while on the highway. The
display will change continuously with uphill and downhill sections but you should quickly be able to identify on level ground the speed range
that your vehicle does the best in.

^ Empty Your Trunk - Avoid leaving unnecessary items in your trunk. It takes power to move increased weight and that means more gasoline
consumption and reduced performance. While the change may be slight, multiplied by thousands of miles, it all adds up.

^ Avoid Extended Idling - There is no need to idle your engine till it reaches operating temperature. Idling wastes fuel.

^ Combine Trips - Your vehicle uses much more fuel when the engine is cold. This is especially true in the winter months when the engine will
take the longest to warm up. Combine errands or trips so that the vehicle only needs to warm up once to encompass many different stops.

DisclaimerTechnical Service Bulletin # 08-08-44-023 Date: 080618

Navigation Radio - Adaptation After Radio/Battery R&R


INFORMATION

Bulletin No.: 08-08-44-023

Date: June 18, 2008


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 513
Chevrolet Venture V6-3.4L VIN E 2838

Subject:
Information On Navigation Radio Not Displaying Accurate Vehicle Location After Radio Replacement, Power Loss Or Battery Replacement

Models:
2009 and Prior GM Passenger Cars and Trucks (Including Saturn)
2009 and Prior HUMMER H2, H3
2009 and Prior Saab 9-7X

with Navigation Radio

The purpose of this bulletin is to inform technicians and customers that the Navigation Radio may not display the vehicle location icon on the map
accurately after a radio or battery has been replaced or after battery power has been removed from the radio. The vehicle location icon accuracy
may be degraded if the GPS signal is not available and the GPS displayed icon has a red line through it.

The Navigation Radio does not keep learned GPS information or gyroscope and vehicle speed signals stored when the battery power is removed
from the radio. The Navigation radio continually uses GPS, gyroscope and vehicle speed data to maintain the vehicle location icon positioned
accurately on the displayed map. There may be periods of time during a drive cycle when the GPS signal may not be available and the vehicle
location icon still appears to be accurate. This is due to the radio having internal gyroscopes and receiving a vehicle speed signal to maintain
accuracy if the radio had received a good GPS signal earlier in the drive cycle.

Normal driving will improve the accuracy of the vehicle location icon on the displayed map. It may be necessary for the vehicle to be driven up to
40 km (25 mi) with 15 left and 15 right turns while the vehicle location icon is matched to roads on the displayed map. Do not replace the radio for
this condition.

DisclaimerTechnical Service Bulletin # 08-03-16-003 Date: 080512

Tire Monitor System - TPM Sensor Information


INFORMATION

Bulletin No.: 08-03-16-003

Date: May 12, 2008

Subject:
Warranty Reduction - Transfer of Tire Pressure Monitoring (TPM) Sensors to Replacement Wheels and Allowable TPM Sensor Replacements

Models:
2000-2009 GM Passenger Cars and Light Duty Trucks (including Saturn)
2003-2009 HUMMER H2
2006-2009 HUMMER H3
2005-2009 Saab 9-7x

with On-Wheel TPM Sensors

TPM Sensor / Wheel Warranty Reviews

During the last warranty review period it was noted that wheels being returned under the GM New Vehicle Warranty were being shipped back to
General Motors with the TPM sensor still attached to the wheel. Return rates ran as high as 60% with the TPM sensors still attached. Operational
TPM sensors should not be returned to GM and are to be transferred to replacement wheels if they become necessary.

Important:
Operational TPM Sensors that are returned under warranty to General Motors will be charged back to the dealer.Sensors have a 10 year
/150,000 mile (240,000 km) battery life, and should be transferred if one or more wheels are replaced.

TPM Valve Stem / Grommet (0-ring) Replacement

When the TPM sensors are transferred to new wheels you should replace the component used to seal the TPM sensor stem to the wheel. On sensors
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 514
Chevrolet Venture V6-3.4L VIN E 2839
with an aluminum stem and visible nut on the outside of the wheel a replacement grommet (0-ring) should be used to assure a proper seal. The
sensor retaining nut (except Aveo) should be tightened to 7 N.m (62 lb in) for all vehicles except Pontiac Vibe (4.0 N.m (35.4 lb in)).

Important:

^ DO NOT overtorque the retaining nut.

Notice:

^ Factory installed TPM Sensors come with plastic aluminum or nickel-plated brass stem caps. These caps should not be changed. Chrome plated
steel caps may cause corrosion of aluminum valve stems due to incompatibility of the metals.

On current style sensors the entire rubber stem is replaceable. The service interval on the revised TPM sensor with replaceable stem is the same as
for any other traditional valve stem. Replace the stem at the time of tire replacement sensor transfer or whenever air seepage is suspected at the
valve stem. When replacing the valve stem tighten the screw to 1.3 N.m (11.5 lb in).

For either style of TPM sensor see the service parts guide for the correct GM part numbers to order and use.

Disclaimer
Technical Service Bulletin # 00-00-89-027E Date: 080929

Interior - Elimination Of Unwanted Odors


INFORMATION

Bulletin No.: 00-00-89-027E

Date: September 29, 2008

Subject:
Eliminating Unwanted Odors in Vehicles

Models:
2009 and Prior GM Passenger Cars and Trucks (including Saturn)
2009 and Prior HUMMER H2, H3 Vehicles
2009 and Prior Saab 9-7X

Supercede:

This bulletin is being revised to add model years and refine the instructions. Please discard Corporate Bulletin Number 00-00-89-027D (Section 00
- General Information).

Vehicle Odor Elimination

General Motors offers a product that may control or eliminate odors in the interior and luggage compartment areas of GM vehicles. GM Vehicle
Care Odor Eliminator is a non-toxic, biodegradable odor remover. This odorless product has been shown to greatly reduce or remove objectionable
smells of mold and mildew resulting from vehicle water leaks (as well as customer created odors, i.e. smoke). You may use GM Vehicle Care Odor
Eliminator on fabrics, vinyl, leather, carpet and sound deadening materials. It may also be induced into HVAC modules and instrument panel ducts
(for the control of non-bacterial related odors).

Important:
This product leaves no residual scent and should not be sold as or considered an air freshener. Product action may result in the permanent
elimination of an odor and may be preferable to customers with allergies who are sensitive to perfumes.

How to Use This Product

GM Vehicle Care Odor Eliminator may be sprayed on in a ready-to-use formula or used in steam cleaners as an additive with carpet shampoo. This
water-based, odorless product is safe for all vehicle interiors. Do not wet or soak any interior surface that plain water would cause to deteriorate, as
this product will have the same effect. Also avoid letting this product come into contact with vinegar or any acidic substance. Acid-based products
will hamper the effectiveness of, or render GM Vehicle Care Odor Eliminator inert.

Note:
Complete eight page treatment sheets are enclosed within each case of GM Vehicle Care Odor Eliminator. These treatment instructions range
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 515
Chevrolet Venture V6-3.4L VIN E 2840
from simple vehicle odor elimination to full step by step procedures for odor removal from water leaks. If lost, contact 800-977-4145 to get a
replacement set faxed or e-mailed to your dealership.

Instructions and cautions are printed on the bottle, but additional help is available. If you encounter a difficult to eliminate or reoccurring odor, you
may call 1-800-955-8591 (in Canada, 1-800-977-4145) to obtain additional information and usage suggestions.

Important:
This product may effectively remove odors when directly contacting the odor source. It should be used in conjunction with diagnostic
procedures (in cases such as a water leak) to first eliminate the root cause of the odor, and then the residual odor to permanently correct the
vehicle condition.

Vehicle Waterleak Odor Elimination

STEP ONE:

Confirm that all water leaks have been repaired. Determine what areas of the vehicle were water soaked or wet. Components with visible
mold/mildew staining should be replaced. Isolate the odor source inside the vehicle. Often an odor can be isolated to an area or component of the
vehicle interior by careful evaluation. Odor evaluation may need to be performed by multiple persons. Another method of isolating an odor source
is to remove and segregate interior trim and components. Plastic sheeting or drop cloths can be used to confine seats, headliners, etc. to assist in
evaluation and diagnoses. If appropriate the vehicle and interior trim should be evaluated separately to determine if the odor stays with the vehicle
or the interior components. Odors that stay with the vehicle may be isolated to insulating and sound deadening materials (i.e. water leak at the
windshield or standing water in the front foot well area caused mold/mildew to form on the bulkhead or kick panel sound deadening pads. If the
interior is removed the floor pan and primed/painted surfaces should be treated with bleach/soap solution, rinsed with clean water and dried.
Interior surfaces should then be treated with GM Vehicle Care Odor Eliminator product before reinstalling carpet or reassembling.

The GM Vehicle Care Odor Eliminator product is an effective odor elimination product when used properly. It must come into direct contact with
the odor source. It should be used in conjunction with diagnostic procedures to first eliminate the root cause of the odor. Some procedures for use
after odor root cause correction are:

STEP TWO:

^ Use the trigger spray head.

^ Put a drop of dish soap the size of a quarter in the bottom of a bottle.

^ Add 8 oz. of GM Vehicle Care Odor Eliminator (1 cup) to the dish soap and top off the bottle with tap water.

^ This formula should be used on hard surfaces (dash, interior plastic molding, and floor pan)

STEP THREE:

The third step to neutralizing the vehicle is a light to medium treatment of all carpeting and upholstered seats with the GM Vehicle Care Odor
Eliminator formula and a wide fan spray setting (at full strength) (i.e.: carpeting on the driver's side requires 4-5 triggers pulls for coverage). The
headliner and trunk should be sprayed next. Lightly brushing the formula into the carpeting and upholstery is a recommended step for deep odor
problems. The dash and all hard surfaces should be sprayed with dish soap/water mixture. Let stand for 1-2 minutes then wipe off the surface.

STEP FOUR: (vehicle ventilation system treatment)

The ventilation system is generally the last step in the treatment of the vehicle.

a. Spray the GM Vehicle Care Odor Eliminator formula into all dash vents. (1-2 trigger pulls per vent).

b. Start the vehicle and turn the vehicle fan on high cool (not A/C setting).

c. Spray the formula (10 trigger pulls) into the outside fresh air intake vent (cowl at base of windshield)

d. Enter the vehicle after 1 minute and wipe off the excess formula spurting out of the dash vents.

e. Smell the air coming from the dash vents. If odors are still present, spray another 5 triggers into the cowl, wait another minute and smell the
results. Once you have obtained a fresh, clean smell coming from the vents, turn the system to the A/C re-circulation setting. Roll up the
windows, spray 3-5 pumps into the right lower IP area and let the vehicle run with the fan set on high for 5-7 minutes.

Please follow this diagnosis process thoroughly and complete each step. If the condition exhibited is resolved without completing every step,
the remaining steps do not need to be performed. If these steps do not resolve the condition, please contact GM TAC for further diagnostic
assistance.

Additional Suggestions to Increase Customer Satisfaction

Here are some additional ideas to benefit your dealership and to generate greater customer enthusiasm for this product.
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 516
Chevrolet Venture V6-3.4L VIN E 2841

^ Keep this product on-hand for both the Service Department and the Used Car lot. Add value to your used car trades; treat loaner and demo cars
during service and at final sale to eliminate smoke, pet, and other common odors offensive to customers. Make deodorizing a vehicle part of
your normal vehicle detailing service.

^ Consider including GM Vehicle Care Odor Eliminator as a give-away item with new vehicle purchases. Many dealers give away as "gifts"
various cleaning supplies at time of delivery. GM Odor Eliminator is one of a few products GM offers that has as many uses in the home as in
the vehicle. Customers may find this product can be used for a host of recreational activities associated with their new vehicle, such as
deodorizing a boat they tow, or a camper.

^ GM Odor Eliminator and many of the GM Vehicle Care products offer you the chance to increase dealership traffic as these superior quality
products cannot be purchased in stores. Many Dealerships have product displays at the parts counter. Consider additional displays in the
Customer Service Lounge, the Showroom and at the Service Desk or Cashier Window. Many customers who purchase vehicles and receive
regular maintenance at your dealership may never visit the parts counter, and subsequently are not exposed to the variety and value that these
products offer.

Parts Information

Disclaimer
Technical Service Bulletin # 02-06-03-008D Date: 080721

Charging System - Low Voltage Display/Battery Discharged


INFORMATION

Bulletin No.: 02-06-03-008D

Date: July 21, 2008

Subject:
Low Voltage Display on IP Gauge, Lights Dim at Stop Lights, Battery Discharged, No Start, Slow Cranking, Dim Lights at Idle, Low Generator
Output

Models:
1990-2009 GM Passenger Cars and Light Duty Trucks (including Saturn)
2003-2009 HUMMER H2, H3
2005-2009 Saab 9-7X

Supercede:

This bulletin is being revised to add the 2009 model year. Please discard Corporate Bulletin Number 02-06-03-008C (Section 06 - Engine).

Any vehicle may have a low voltage display (if equipped with gauges), lights that dim at stop lights, slow cranking, no start, low generator output at
idle or dim lights at idle when electrical loads are heavy at idle or under slow driving or infrequent usage conditions. These characteristics may be
more noticeable with customer added electrical accessories, or with a discharged battery. These are normal operating characteristics of a vehicle
electrical system and no repairs should be attempted unless a proven fault has been diagnosed.

During normal driving conditions, when engine speed is above 1000 RPM, the generator is designed to do two things:

^ Supply the current necessary to operate the vehicle's originally equipped electrical devices (loads).

^ Recharge/maintain the battery's state of charge.

The following factors may affect generator and battery performance:

^ Non-usage of the vehicle for extended periods of time. The vehicle's computers, clocks and the like will cause the battery state of charge to drop
(For example; 30 days in a parking lot and the vehicle may not start because of a dead battery or a vehicle which is driven only a short distance
once a week may end up with a discharged battery to the point where the vehicle may not start). This would be considered abnormal usage of
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 517
Chevrolet Venture V6-3.4L VIN E 2842
the vehicle and the normally expected result for the vehicle battery, generator and electrical systems.

^ At idle, vehicle electrical loads may exceed the low speed current (amperage) output of the generator and when this happens the shortfall comes
from the battery. This will result in a drop in the electrical system voltage as the battery delivers the additional electrical current to meet the
demand. This is equivalent to the brown outs experienced by homes and businesses when the electrical demand is more than the supply. See
Figure 1.

^ Extended periods of engine idling, with high electrical loads, may result in a discharged battery. Attempting to recharge a battery by letting the
engine run at idle may not be beneficial unless all electrical loads are turned "OFF".

^ Increased internal generator temperatures from extended idling can also contribute to lower electrical system voltage. As the generator's internal
temperature rises, the generator's output capability is reduced due to increased electrical resistance.

Some typical examples of electrical loads are shown above.

Depending on the vehicle application, generator current (amperage) output at engine idle speeds of 600-700 RPM can be as low as 35 percent of the
full rated output. With enough electrical loads "ON", it is easy to exceed the generator current (amperage) output when the engine is at an idle of
600-700 RPM. This is a normal condition. The battery supplements for short periods of time. Items that affect the vehicle's electrical system current
and voltage at idle are the number of electrical loads being used, including add-on accessories, and extended idle times. When the vehicle speed is
above approximately 24 km/h (15 mph), the engine/generator RPM is high enough and the generator current (amperage) output is sufficient to
supply the current (amperage) requirements of the vehicle as originally equipped and recharge the battery.

Dimming lights at idle may be considered normal for two reasons:

1. As the engine/generator speed changes, so will the current (amperage) output of the generator. As a vehicle slows, engine/generator RPM
slows and the current (amperage) output of the generator may not be sufficient to supply the loads, the vehicle system voltage will drop and
the lights will dim. Dimming of the lights is an indication that current is being pulled from the battery. If the battery is in a low
state-of-charge (discharged condition), the driver will notice a more pronounced dimming than a vehicle with a fully charged battery.

2. When high current loads (blower, rear defogger, headlamps, cooling fan, heated seats, power seats, electric "AIR" pump, or power windows)
are operating or cycled "ON", the generator's voltage regulator can delay the rise in output. This effect, usually at lower engine speeds, can
take up to ten seconds to ramp up the generator output. This is done to avoid loading the engine severely. To increase current (amperage)
output, additional torque is consumed by the generator. The engine computer (ECM/PCM) will ramp up engine/generator speed in small
steps so engine speed variations are not noticeable to the driver.
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 518
Chevrolet Venture V6-3.4L VIN E 2843

For diagnosis of the battery and/or the generator, refer to the appropriate Service Information (SI) or Corporate Bulletin Number
05-06-03-002C.

Disclaimer

Technical Service Bulletin # 05-06-02-001A Date: 080716

Cooling System, A/C - Aluminum Heater Cores/Radiators


INFORMATION

Bulletin No.: 05-06-02-001A

Date: July 16, 2008

Subject:
Information On Aluminum Heater Core and/or Radiator Replacement

Models:
2005 and Prior GM Passenger Cars and Light Duty Trucks (including Saturn)
2003-2005 HUMMER H2

Supercede:

This bulletin is being revised to update the Warranty Information. Please discard Corporate Bulletin Number 05-06-02-001 (Section 06 -
Engine/Propulsion System).

Important:
2004-05 Chevrolet Aveo (Pontiac Wave, Canada Only) does not use DEX-COOL(R). Refer to the flushing procedure explained later in this
bulletin.

The following information should be utilized when servicing aluminum heater core and/or radiators on repeat visits. A replacement may be
necessary because erosion, corrosion, or insufficient inhibitor levels may cause damage to the heater core, radiator or water pump. A coolant check
should be performed whenever a heater core, radiator, or water pump is replaced. The following procedures/ inspections should be done to verify
proper coolant effectiveness.

Caution:
To avoid being burned, do not remove the radiator cap or surge tank cap while the engine is hot. The cooling system will release scalding fluid
and steam under pressure if the radiator cap or surge tank cap is removed while the engine and radiator are still hot.

Important:
If the vehicle's coolant is low, drained out, or the customer has repeatedly added coolant or water to the system, then the system should be
completely flushed using the procedure explained later in this bulletin.

Technician Diagnosis

^ Verify coolant concentration. A 50% coolant/water solution ensures proper freeze and corrosion protection. Inhibitor levels cannot be easily
measured in the field, but can be indirectly done by the measurement of coolant concentration. This must be done by using a Refractometer J
23688 (Fahrenheit scale) or J 26568 (centigrade scale), or equivalent, coolant tester. The Refractometer uses a minimal amount of coolant that
can be taken from the coolant recovery reservoir, radiator or the engine block. Inexpensive gravity float testers (floating balls) will not
completely analyze the coolant concentration fully and should not be used. The concentration levels should be between 50% and 65% coolant
concentrate. This mixture will have a freeze point protection of -34 degrees Fahrenheit (-37 degrees Celsius). If the concentration is below 50%,
the cooling system must be flushed.

^ Inspect the coolant flow restrictor if the vehicle is equipped with one. Refer to Service Information (SI) and/or the appropriate Service Manual
for component location and condition for operation.

^ Verify that no electrolysis is present in the cooling system. This electrolysis test can be performed before or after the system has been repaired.
Use a digital voltmeter set to 12 volts. Attach one test lead to the negative battery post and insert the other test lead into the radiator coolant,
making sure the lead does not touch the filler neck or core. Any voltage reading over 0.3 volts indicates that stray current is finding its way into
the coolant. Electrolysis is often an intermittent condition that occurs when a device or accessory that is mounted to the radiator is energized.
This type of current could be caused from a poorly grounded cooling fan or some other accessory and can be verified by watching the volt
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 519
Chevrolet Venture V6-3.4L VIN E 2844
meter and turning on and off various accessories or engage the starter motor. Before using one of the following flush procedures, the coolant
recovery reservoir must be removed, drained, cleaned and reinstalled before refilling the system.

Notice:
^ Using coolant other than DEX&hyphen;COOL(R) may cause premature engine, heater core or radiator corrosion. In addition, the engine
coolant may require changing sooner, at 30,000 miles (50,000 km) or 24 months, whichever occurs first. Any repairs would not be covered
by your warranty. Always use DEX&hyphen;COOL(R) (silicate free) coolant in your vehicle.

^ If you use an improper coolant mixture, your engine could overheat and be badly damaged. The repair cost would not be covered by your
warranty. Too much water in the mixture can freeze and crack the engine, radiator, heater core and other parts.

Flushing Procedures using DEX-COOL(R)

Important:
The following procedure recommends refilling the system with DEX-COOL(R), P/N 12346290 (in Canada, use P/N 10953464), GM
specification 6277M. This coolant is orange in color and has a service interval of 5 years or 240,000 km (150,000 mi). However, when used on
vehicles built prior to the introduction of DEX-COOL(R), maintenance intervals will remain the same as specified in the Owner's Manual.

^ If available, use the approved cooling system flush and fill machine (available through the GM Dealer Equipment Program) following the
manufacturer's operating instructions.

^ If approved cooling system flush and fill machine is not available, drain the coolant and dispose of properly following the draining procedures
in the appropriate Service Manual. Refill the system using clear, drinkable water and run the vehicle until the thermostat opens. Repeat and run
the vehicle three (3) times to totally remove the old coolant or until the drained coolant is almost clear. Once the system is completely flushed,
refill the cooling system to a 50%-60% concentration with DEX&hyphen;COOL(R), P/N 12346290 (in Canada, use P/N 10953464), GM
specification 6277M, following the refill procedures in the appropriate Service Manual.

If a Service Manual is not available, fill half the capacity of the system with 100% DEX-COOL(R), P/N 12346290 (in Canada, use P/N 10953464),
GM specification 6277M. Then slowly add clear, drinkable water (preferably distilled) to the system until the level of the coolant mixture has
reached the base of the radiator neck. Wait two (2) minutes and reverify the coolant level. If necessary, add clean water to restore the coolant to the
appropriate level.

Once the system is refilled, reverify the coolant concentration using a Refractometer J 23688 (Fahrenheit scale) or J 26568 (centigrade scale)
coolant tester, or equivalent. The concentration levels should be between 50% and 65%.

Flushing Procedures using Conventional Silicated (Green Colored) Coolant

Important:
2004-2005 Chevrolet Aveo (Pontiac Wave, Canada Only) does not use DEX&hyphen;COOL(R). The Aveo and Wave are filled with
conventional, silicated engine coolant that is blue in color. Silicated coolants are typically green in color and are required to be drained, flushed
and refilled every 30,000 miles (48,000 km). The Aveo and Wave are to be serviced with conventional, silicated coolant. Use P/N 12378560 (1
gal) (in Canada, use P/N 88862159 (1 L). Refer to the Owner's Manual or Service Information (SI) for further information on OEM coolant.

Important:
Do not mix the OEM orange colored DEX-COOL(R) coolant with green colored coolant when adding coolant to the system or when servicing
the vehicle's cooling system. Mixing the orange and green colored coolants will produce a brown coolant which may be a customer dissatisfier
and will not extend the service interval to that of DEX-COOL(R). Conventional silicated coolants offered by GM Service and Parts Operations
are green in color.

^ If available, use the approved cooling system flush and fill machine (available through the GM Dealer Equipment Program) following the
manufacturer's operating instructions.

^ If approved cooling systems flush and fill machine is not available, drain coolant and dispose of properly following the draining procedures in
appropriate Service Manual. Refill the system using clear, drinkable water and run vehicle until thermostat opens. Repeat and run vehicle three
(3) times to totally remove old coolant or until drained coolant is almost clear. Once the system is completely flushed, refill the cooling system
to a 50%-60% concentration with a good quality ethylene glycol base engine coolant, P/N 12378560, 1 gal (in Canada, use P/N 88862159 1 L),
conforming to GM specification 1825M, or recycled coolant conforming to GM specification 1825M, following the refill procedures in the
appropriate Service Manual.

If a Service Manual is not available, fill half the capacity of the system with 100% good quality ethylene glycol base (green colored) engine
coolant, P/N 12378560 1 gal., (in Canada, use P/N 88862159 1 L) conforming to GM specification 1825M. Then slowly add clear, drinkable water
(preferably distilled) to system until the level of the coolant mixture has reached the base of the radiator neck. Wait two (2) minutes and recheck
coolant level. If necessary, add clean water to restore coolant to the appropriate level.

Once the system is refilled, recheck the coolant concentration using a Refractometer J 23688 (Fahrenheit scale) or J 26568 (centigrade scale)
coolant tester, or equivalent. Concentration levels should be between 50% and 65%.
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 520
Chevrolet Venture V6-3.4L VIN E 2845

Parts Information

Warranty Information

For vehicles repaired under warranty, use the table.

DisclaimerTechnical Service Bulletin # 05-03-07-009B Date: 080627

Alignment - Specifications/Requirements/Recommendations
INFORMATION

Bulletin No.: 05-03-07-009B

Date: June 27, 2008

Subject:
Wheel Alignment Specifications, Requirements and Recommendations for GM Vehicles

Models:
2009 and Prior GM Passenger Cars and Light Duty Trucks (Including Saturn)
2009 and Prior HUMMER H2, H3
2009 and Prior Saab 9-7X

Supercede:

This bulletin is being revised to add 2008 & 2009 model years. Please discard Corporate Bulletin Number 05-03-07-009A (Section 03 -
Suspension).

The purpose of this bulletin is to provide retail and wholesale personnel with General Motors specifications, requirements and recommendations for
wheel alignment equipment and alignment procedures.

Wheel Alignment Specifications

Technicians must refer to SI for the correct wheel alignment specifications for each vehicle. SI is the only source of GM wheel alignment
specifications that is up-to-date throughout the year. The wheel alignment specifications loaded in any wheel alignment machine by the equipment
manufacturer may be incorrect and/or outdated, even if the dealership subscribes to the manufacturer's update service. GM used to send certain
manufacturers an annual update of the wheel alignment specifications for the new model year in early summer. Certain equipment manufacturers
now subscribe to GM's SI service to obtain updates for GM alignment specifications, however, because changes to the wheel alignment
specifications may occur during the model year, dealership alignment machines may or may not be up to date with the current specifications.
Therefore, it is required that the technicians refer directly to SI for the latest updates and any changes to the wheel alignment specifications.

Using incorrect and/or outdated specifications may result in unnecessary adjustments, irregular and/or premature tire wear and repeat customer
concerns.

Conditions Possibly Requiring a Wheel Alignment

^ Lead/pull defined as "at a constant highway speed on a typical straight road, the amount of effort required at the steering wheel to maintain the
vehicle's straight path."
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 521
Chevrolet Venture V6-3.4L VIN E 2846

^ Steering wheel off-center (clockwise or counterclockwise)

^ Unusual tire wear (slight to very slight "feathering" or "edge" wear on the shoulders of tires is NOT considered unusual and should even up
with a tire rotation at or before the next scheduled maintenance interval)

^ Other repairs that affect wheel alignment

Alignment Equipment

Alignments must be performed with a quality alignment machine that will give accurate results when performing alignment checks. "External
Reference" (image-based camera technology) is preferred.

Requirements

^ Computerized four wheel alignment system

^ Computer capable of printing before and after alignment reports

^ Computer capable of time and date stamp printout

^ Racking system must have jacking capability

^ Racking system must be capable of level to 1.6 mm (1/16 in)

^ Appropriate wheel stops and safety certification

^ Built-in turn plates and slip plates

^ Wheel clamps capable of attaching to 20" or larger wheels

^ Racking capable of accepting any GM passenger car or light duty truck

^ Operator properly trained and ASE-certified (U.S. only) in wheel alignment

Recommendations

Racking should have front and rear jacking capability.

Equipment Maintenance and Calibration

Alignment machines must be regularly calibrated in order to give correct information. Most manufacturers recommend the following:

^ Alignment machines with "internal reference" sensors should be checked (and calibrated, if necessary) every six months.

^ Alignment machines with "external reference" (image-based camera technology) should be checked (and calibrated, if necessary) once a year.

^ Racks must be kept level to within 1.6 mm (1/16 in).

^ If any instrument that is part of the alignment machine is dropped or damaged in some way, check the calibration immediately.

Check with the manufacturer of your specific equipment for their recommended service/calibration schedule.

Warranty Claim Documentation

Important:
Failure to have proper documentation of the repair order may result in denial or chargeback of the warranty claim.

In order to properly document a warranty claim for alignment, the following must be completed:

^ Details of the customer's concern or complaint are to be noted at the time of repair order write-up by recording the description of the customer's
problem.

^ The technician's description of the cause of the concern and the repairs performed must be written on all copies of the repair order.

^ "Before" and "After" alignment settings are to be recorded on the repair order. An alignment machine printout of "Before" AND "After"
settings with date/time stamp is to be attached to the repair order by dealers who have printout capable equipment.

^ Documentation of alignment machine calibration within the last 12 months must be available for AVM (in Canada, DSM, for Saturn, DSSM)
review upon request.
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 522
Chevrolet Venture V6-3.4L VIN E 2847

^ Prior wholesale approval required for vehicles under 800 km (500 mi) or over 12,000 km (7,500 mi) (will now apply to Saturn retailers also).
Refer to the GM Service Policies and Procedures Manual for complete warranty policy information.

Alignment Process

When performing wheel alignment measurement and/or adjustment, the following steps should be taken:

Preliminary Steps

1. Verify that the vehicle has a full tank of fuel (compensate as necessary).

2. Inspect the wheels and the tires for damage.

3. Inspect the tires for the proper inflation and irregular tire wear.

4. Inspect the wheel bearings for excessive play.

5. Inspect all suspension and steering parts for looseness, wear, or damage.

6. Inspect the steering wheel for excessive drag or poor return due to stiff or rusted linkage or suspension components.

7. Inspect the vehicle trim height.

8. Compensate for frame angle on targeted vehicles (refer to Wheel Alignment Specifications in SI).

Satisfactory vehicle operation may occur over a wide range of alignment angles. However, if the wheel alignment angles are not within the range of
specifications, adjust the wheel alignment to the specifications. Refer to Wheel Alignment Specifications in SI. Give consideration to excess loads,
such as tool boxes, sample cases, etc. Follow the alignment equipment manufacturer's instructions.

Measure/Adjust

Notice:
Prior to making any adjustments to wheel alignment on a vehicle, technicians must verify that the wheel alignment specifications loaded into
the wheel alignment machine are up-to-date by comparing these to the wheel alignment specifications for the appropriate model and model year
in SI. Using incorrect and/or outdated specifications may result in unnecessary adjustments, irregular and/or premature tire wear and repeat
customer concerns.

Important:
When performing adjustments to vehicles requiring a 4-wheel alignment, set the rear wheel alignment angles first in order to obtain proper front
wheel alignment angles.

Perform the following steps in order to measure the front and rear alignment angles:

1. Install the alignment equipment according to the manufacturer's instructions.

2. Jounce the front and the rear bumpers 3 times prior to checking the wheel alignment.

3. Measure the alignment angles and record the readings.

Adjust alignment angles to vehicle specification, if necessary. Refer to Wheel Alignment Specifications in SI.

Test drive the vehicle to ensure proper repair.

DisclaimerTechnical Service Bulletin # 05-03-10-005D Date: 080911

Wheels/Tires - Upsized Wheel/Tire Characteristics


INFORMATION

Bulletin No.: 05-03-10-005D

Date: September 11, 2008


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 523
Chevrolet Venture V6-3.4L VIN E 2848

Subject:
Performance Characteristics of Vehicles with Accessory Wheel/Tire Assemblies Installed as "Upsized" to Original Equipment

Models:
2009 and Prior GM Passenger Cars and Light Duty Trucks (including Saturn)
20062009 HUMMER H3

Supercede:

This bulletin is being revised to add the 2009 model year. Please discard Corporate Bulletin Number 05-03-10-005C (Section 03 - Suspension).

When GM Accessories wheel/tire assemblies are installed on a vehicle, customers may notice a change in the driving characteristics of the vehicle.
The purpose of this document is to review the different performance characteristics of a vehicle with accessory wheel/tire assemblies installed.

Vehicle Performance:

Use of larger "upsized" tire/wheel assemblies, in lieu of the standard factory installed tire/wheel assemblies, can change the vehicle's overall
performance characteristics. Depending on road surface and driving conditions, the driver may note changes or differences in the following:

^ Tire/road noise

^ Ride stiffness

^ Tire tread wear rate

^ Steering effort

^ Fuel economy

^ Braking performance

^ Tire traction (wet/dry/snow/ice) Also, generally, tire chains cannot be used due to lack of clearance to the wheelhouse. Trucks equipped with
accessory will not be compatible for use with snowplow equipment.

Turning Information:

Important:
This section ONLY applies to the following vehicles:

^ 1999-2007 Silverado and Sierra (Classic)

^ 2000-2006 Fullsize Utilities

In a reverse turn, the tire may contact the plastic inner liner toward the rear and may also contact the sway bar. In a bounce/jounce condition, the
tire may contact the top of the wheel house (the metal part inside the fender lip). These are all considered friendly surface contacts, meaning they
will not damage the tire/wheel and are a characteristic of the upgrade.

Warranty Information

All GM accessories sold and permanently installed on a GM vehicle prior to delivery will be covered under the provisions of the New Vehicle
Limited Warranty.

The changes in ride handling listed above are considered normal conditions when upgrading to larger wheels/tires and are not covered by the New
Vehicle Limited Warranty.

Wheels

For the U.S., in the event GM Accessories are installed AFTER new vehicle delivery, or are replaced under the new vehicle warranty, they will be
covered (parts and labor) for the balance of the vehicle warranty, but in no event less than 12 months/12,000 miles. This coverage is only effective
for GM Accessories permanently installed by a GM dealer or a GM approved ADI (Accessory Distributor / Installer).

For Canada, in the event GM Accessories are installed AFTER new vehicle delivery, they will be covered (parts and labor) for the balance of the
vehicle warranty, or up to 12 months/unlimited kilometers depending on month installed. For replacement after the new vehicle warranty expires,
but within the 12 months/unlimited kilometers coverage, refer to claim type "B" guidelines.

GM Accessories sold over-the-counter, or those not requiring installation, will continue to receive the standard GM Dealer Parts Warranty of 12
months from the date of purchase (parts only).

Tires:
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 524
Chevrolet Venture V6-3.4L VIN E 2849

Any approved tire installed on a GM Vehicle PRIOR to delivery will be covered under the provisions of the New Vehicle Limited Warranty. Tires
are covered against defects in material and workmanship. Tires are warranted for defects "without" prorated charge for tread mileage. Subsequent
replacements under this warranty will continue to be covered for the remainder of the New Vehicle Limited Warranty.

Any approved tire installed on a GM Vehicle PRIOR to delivery, may continue to be warranted on a prorated basis by the tire manufacturer once
the New Vehicle Limited Warranty expires.

Any approved tire installed AFTER delivery will be covered under the provisions of the tire manufacturer warranty. U.S. dealers should refer to
GM Warranty Administration Bulletin 00-03-10-003M and GM Parts Process/Policy Bulletin 1B03001 for more information.

Canadian dealers should refer to GM Warranty Administration Bulletin 01-03-10-003E.

Disclaimer

Technical Service Bulletin # 08-08-44-026 Date: 080811

Audio System - Refurbishing Radio Faceplates/Knobs


INFORMATION

Bulletin No.: 08-08-44-026

Date: August 11, 2008

Subject:
Information on Refurbish Instead of Replace Out of Warranty Radios with Worn Graphics on Faceplate, Knobs or Buttons

Models:
2009 and Prior GM Passenger Cars and Trucks (Including Saturn)
2009 and Prior HUMMER H2, H3
2009 and Prior Saab 9-7X

Attention:
This bulletin applies to vehicles out of warranty and sold in the United States only.

Some customers may have concerns about the wear on the radio faceplate, knobs or buttons and their vehicle is out of warranty requiring a
customer pay repair.

GM authorized Electronic Service Centers may have the ability to refurbish out of warranty radios instead of replacing it. To determine if
refurbishment is available, please contact an authorized GM Electronic Service Center (ESC). This may result in a considerable cost savings to the
customer.

For vehicles in warranty, follow the normal procedure of exchanging the radio at an authorized Electronic Service Center Service Center.
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 525
Chevrolet Venture V6-3.4L VIN E 2850

DisclaimerTechnical Service Bulletin # 08-08-44-028 Date: 080828

Audio - Inadvertent Steering Wheel Button Activation


INFORMATION

Bulletin No.: 08-08-44-028

Date: August 28, 2008

Subject:
Information On Inadvertent Steering Wheel Control (SWC) Button Press Causing Radio Anomalies

Models:
2009 and Prior GM Passenger Cars and Trucks (Including Saturn)
2009 and Prior HUMMER H2, H3 Models
2009 and Prior Saab 9-7X

All Vehicles with Steering Wheel Controls

This bulletin is being issued to provide a recommendation for vehicles with a customer concern of the radio station tuning changing by itself,
volume changing by itself, radio changing by itself, or radio muting or going silent when driving and turning the steering wheel.

The switches on the right hand side of the steering wheel are easily pressed and may inadvertently be pressed when turning the steering wheel.

These concerns may be affected by the location of the steering wheel controls.

Recommendation

Do Not Replace The Radio

1. Please determine that the switch controls on the steering wheel are functioning correctly.

2. Ask the customer if their hand was in close proximity to the steering wheel controls when the condition happened. Explain to the customer
that bumping the controls would have caused this undesired action. Explain to the customer the proper use and function of the steering wheel
controls.

DisclaimerTechnical Service Bulletin # 08-08-46-004 Date: 080814

OnStar(R) - Aftermarket Device Interference Information


INFORMATION

Bulletin No.: 08-08-46-004

Date: August 14, 2008

Subject:
Information on Aftermarket Device Interference with OnStar(R) Diagnostic Services

Models:
2009 and Prior GM Passenger Car and Truck (including Saturn)
2009 and Prior HUMMER H2, H3 Models
2009 and Prior Saab 9-7X

with OnStar(R) (RPO UE1)

This bulletin is being issued to provide dealer service personnel with information regarding aftermarket devices connected to the Diagnostic Link
Connector (DLC) and the impact to OnStar(R) diagnostic probes and Vehicle Diagnostic e-mails.

Certain aftermarket devices, when connected to the Diagnostic Link Connector, such as, but not limited to, Scan Tools, Trip Computers, Fuel
Economy Analyzers and Insurance Tracking Devices, interfere with OnStar's ability to perform a diagnostic probe when requested (via a blue
button call) by a subscriber. These devices also prohibit the ability to gather diagnostic and tire pressure data for a subscriber's scheduled OnStar(R)
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 526
Chevrolet Venture V6-3.4L VIN E 2851
Vehicle Diagnostic (OVD) e-mail.

These aftermarket devices utilize the Vehicles serial data bus to perform data requests and/or information gathering. When these devices are
requesting data, OnStar(R) is designed not to interfere with any data request being made by these devices as required by OBD II regulations.

The OnStar(R) advisor is unable to definitively detect the presence of these devices and will only be able to inform the caller or requester of the
unsuccessful or incomplete probe and may in some cases refer the subscriber/requester to take the vehicle to a dealer for diagnosis of the concern.

When performing a diagnostic check for an unsuccessful or incomplete OnStar(R) diagnostic probe, or for concerns regarding completeness of the
OnStar(R) Vehicle Diagnostic (OVD) e-mail, verify that an aftermarket device was not present at the time of the requested probe. Regarding the
OVD e-mail, if an aftermarket device is interfering (including a Scan Tool of any type), the e-mail will consistently display a "yellow" indication in
diagnostics section for all vehicle systems except the OnStar(R) System and Tire Pressure data (not available on all vehicles) will not be displayed
(i.e. section is collapsed). Successful diagnostic probes and complete OVD e-mails will resume following the removal or disconnecting of the
off-board device.

DisclaimerTechnical Service Bulletin # 06-08-64-007A Date: 080922

OnStar(R) - Analog Only Systems Information


INFORMATION

Bulletin No.: 06-08-64-007A

Date: September 22, 2008

Subject:
Information on OnStar(R) Analog-Only Systems

Models

Supercede:

This bulletin is being revised to update the models affected list above. Please discard Corporate Bulletin Number 06-08-46-007 (Section 08 - Body
& Accessories).

All vehicles equipped with OnStar(R) listed in this bulletin were built with Analog-Only OnStar(R) Hardware. OnStar(R) equipped vehicles with
analog-only equipment were designed to operate only on the analog wireless network and cannot be upgraded for digital network compatibility.

Vehicles with this equipment will no longer be able to receive OnStar(R) services beginning January 1, 2008. At that time, service will be available
only through Dual-Mode (Analog / Digital) equipment. Analog-Only vehicles cannot be upgraded to digital equipment.
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 527
Chevrolet Venture V6-3.4L VIN E 2852

DisclaimerTechnical Service Bulletin # 01-07-30-032E Date: 080929

A/T - 4T65E Fluid Leaking From A/T Vent


TECHNICAL

Bulletin No.: 01-07-30-032E

Date: September 29, 2008

Subject:
Transmission Oil Leaking From Transmission Vent (Replace Transmission Case Cover (Channel Plate) Gasket)

Models:
1997-2009 GM Passenger Cars and Light Duty Trucks (including Saturn)

with Hydra-Matic 4T65-E Automatic Transmission (RPOs MN3, MN7, M15, M76)

Supercede:

This bulletin is being revised to add the 2008 and 2009 model years. Please discard Corporate Bulletin Number 01-07-30-032D (Section 07 -
Transmission/Transaxle).

Condition

Some customers may comment on a transmission oil leak.

Cause

This condition may be caused by an improperly torqued channel plate gasket.

Correction

To correct this condition, replace the case cover (channel plate) gaskets (429 and 430). Refer to Unit Repair publication in SI of the appropriate
vehicle being serviced.

Visual inspection of the upper gasket (1) will reveal damage at the referenced area.

Parts Information

Warranty Information
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 528
Chevrolet Venture V6-3.4L VIN E 2853

For vehicles repaired under warranty, use the table.

Disclaimer

Technical Service Bulletin # 01-06-01-011E Date: 081218

Gasoline Engine - Oil Consumption Guidelines


INFORMATION

Bulletin No.: 01-06-01-011E

Date: December 18, 2008

Subject:
Information on Engine Oil Consumption Guidelines

Models:
1998-2009 GM Passenger Cars and Gasoline Powered Light Duty Trucks Under 8500 LB GVW (Including Saturn)

2003-2009 HUMMER H2
2006-2009 HUMMER H3
2005-2009 Saab 9-7X

Supercede:

This bulletin is being revised to update model years. Please discard Corporate Bulletin Number 01-06-01-011D (Section 06 - Engine/Propulsion
System).

All engines require oil to lubricate and protect the load bearing and internal moving parts from wear including cylinder walls, pistons and piston
rings. When a piston moves down its cylinder, a thin film of oil is left on the cylinder wall. During the power stroke, part of this oil layer is
consumed in the combustion process. As a result, varying rates of oil consumption are accepted as normal in all engines.

Oil Consumption

The accepted rate of oil consumption for engines used in the vehicles referenced is 0.946 liter (1 qt) in 3200 km (2000 mi).

Important:
Certain models have a new GM Extended Warranty. Please refer to the appropriate Owner's Manual for warranty information.

This rate only applies to personal use vehicles, under warranty, that are driven in a non-aggressive manner and maintained in accordance with the
appropriate maintenance schedule, with less than 58,000 km (36,000 mi), or 80,450 km (50,000 mi) for Cadillac, driven at legal speeds in an
unloaded (for trucks) condition.

Important:
This rate does not apply to vehicles that are driven in an aggressive manner, at high RPM, high speeds, or in a loaded condition (for trucks). Oil
consumption for vehicles driven under these conditions will be more.

Many factors can affect a customer's concern with oil consumption. Driving habits and vehicle maintenance vary from owner to owner. Thoroughly
evaluate each case before deciding whether the vehicle in question has abnormal engine oil consumption.

Gasket and External Leaks

Inspect the oil pan and engine covers for leakage due to over-tightened, damaged, or out of place gaskets. Inspect oil lines and fittings for signs of
leakage.

Improper Reading of the Oil Level Indicator (Dipstick)


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 529
Chevrolet Venture V6-3.4L VIN E 2854

Verify that the dipstick tube is fully seated in the block. When checking the oil level, make sure the dipstick is wiped clean before taking an oil
level reading and fully depress the dipstick until the shoulder bottoms out on the dipstick tube. The dipstick should be the proper part number for
the engine/vehicle that is being checked.

Notice:
Operating your vehicle with an oil level that is below the minimum level indicated on the engine oil dipstick can result in severe engine damage.
Repairs resulting from operating an engine with insufficient oil are not covered under the terms of the New Vehicle Warranty.

Important:
Refer to Owner Manual in SI for checking and adding engine oil.

Not Waiting Long Enough After Running Engine to Check Oil Level

Some engines require more time than others for the oil to drain back into the crankcase. To assure a sufficient amount of oil has drained back to the
crankcase, and an accurate reading can be obtained, the vehicle should be allowed to sit for at least 15 minutes, after the engine has been shut off,
before taking an oil level reading. In order to ensure accurate results, the temperature of the oil should be close to the same temperature as the last
time the oil level was checked.

Important:
This does not apply to some Corvette ZO6 equipped with the 7.0L LS7 engine (dry sump). Follow the instructions in the Owner's Manual for
checking the oil in this application.

Improper Oil Fill After an Oil Change

Following an oil change, verify that the proper amount and type of oil was put in the engine and that the oil level on the dipstick is not above the
full mark or below the add marks. Refer to the Owner's Manual or Service Manual for information on recommended oil quantity, viscosity, and
quality.

Aggressive Driving, High Speed or High RPM Driving

Aggressive driving and/or continuous driving at high speeds/high RPMs will increase oil consumption. Because this may not always be an
everyday occurrence, it is hard to determine exactly how much the oil economy will be affected.

A higher rate of oil consumption is normal for vehicles equipped with manual transmissions that are driven aggressively. By "aggressive," we mean
operation at high RPM (3,000 RPM to redline), with frequent use of engine braking (using the engine to slow the vehicle). Vehicles that are driven
aggressively may consume engine oil at a rate of up to 0.946 L (1 quart) every 805 km (500 mi). This is normal for a vehicle that is driven
aggressively. No repair is necessary. This characteristic does, however, require the owner to check the engine oil level at sufficiently frequent
intervals, especially when driving aggressively, to assure the oil level remains within the recommended operating range. As the Owner's Manual
recommends, you should check the oil level every time you get fuel.

Towing or Heavy Usage

Towing a trailer will increase oil consumption and may cause oil consumption to fall below the normal accepted rate referenced in this bulletin for
an unloaded vehicle in a personal use application. Large frontal area trailers will further increase the work required from the engine, especially at
highway speeds, and thus increases the rate of oil consumption.

Crankcase Ventilation System

Verify that the positive crankcase ventilation (PCV) system is operating properly. Blockages, restrictions, or damage to the PCV system can result
in increased oil use.

Oil Dilution (Fuel and Water)

On vehicles that are usually driven short distances, less than 8 km (5 mi), especially in colder weather, unburned fuel and condensation generated
from cold engine operation may not get hot enough to evaporate out of the oil. When this occurs, the dipstick may indicate that the oil level is
over-full. Subsequent driving on a trip of sufficient length to enable normal engine operating temperature for 30 minutes or more, in order to
vaporize excess moisture and fuel, may give the customer the impression of excessive oil consumption.

Engine Temperature

If an engine is run at overheated temperatures (see Owner's Manual or Service Manual) for more than brief periods, oil will oxidize at a faster than
normal rate. In addition, gaskets may distort, piston rings may stick, and excessive wear may result. Verify that all cooling system components are
in proper working order.

Engine Wear

Piston scuffing, excessive piston-to-wall clearance, tapered or out of round cylinders, worn, damaged or improperly installed valve guides, seals
and piston rings will all cause an increase in oil consumption.
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 530
Chevrolet Venture V6-3.4L VIN E 2855

Measurement of Oil Consumption

Engines require a period of time to BREAK IN so that moving parts are properly seated. Therefore, oil economy should not be tested until the
vehicle has accumulated at least 6400 km (4000 mi). An exception would be allowed only if an engine is reported to be using more than 0.946 liter
(1 qt) in 1600 km (1000 mi).

1. Verify that the engine has no external leaks. Repair as necessary.

2. Verify that the engine is at normal operating temperature (see Owner's Manual or Service Manual).

3. Park the vehicle on a level surface.

4. Wait at least 15 minutes, after the engine is shut off, before checking the oil level to make sure that the oil has had time to drain back into the
crankcase.

5. Verify that the oil level is at, but not above, the full mark on the dipstick, and that the proper viscosity and quality oil are being used as
recommended in the Owner's Manual.

6. Record the vehicle mileage, date, and exact oil level on the form shown above.

7. Ask the customer to verify the oil level, each time the vehicle is fueled, following steps 16 and return the vehicle to the dealership if the oil
level is found at or below the add mark, 0.946 liter (1 qt) low. If the oil level remains above the add mark, the customer should continue to
operate the vehicle and verify the engine oil level until 3200 km (2000 mi) has accumulated before returning to the dealership for a final
evaluation.

8. If the final evaluation shows that the engine uses more than 0.946 liter (1 qt) in 3200 km (2000 mi), follow the published symptom
diagnostics as described in the appropriate Service Manual. If the oil consumption test shows that the engine uses less than 0.946 liter (1 qt)
in 3200 km (2000 mi), explain to the customer that their engine meets the guidelines for oil consumption.

DisclaimerTechnical Service Bulletin # 00-00-90-002J Date: 090128

Tires - Correct Inflation Pressure Information


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 531
Chevrolet Venture V6-3.4L VIN E 2856
INFORMATION

Bulletin No.: 00-00-90-002J

Date: January 28, 2009

Subject:
Information on Proper Tire Pressure

Models:
2010 and Prior GM Passenger Cars and Light Duty Trucks (including Saturn)
2009 and Prior HUMMER H2, H3, H3T
2005-2009 Saab 9-7X

Supercede:

This bulletin is being revised to add model years and clarify additional information. Please discard Corporate Bulletin Number 00-00-90-002I
(Section 00 - General Information).

Important:
^ Adjustment of tire pressure for a customer with a Low Tire Pressure Monitor (TPM) light on and no codes in the TPM system is NOT a
warrantable repair. Claims to simply adjust the tire pressure will be rejected.

^ ALL tires (including the spare tire) MUST be set to the recommended inflation pressure stated on the vehicle's tire placard (on driver's door)
during the PRE-DELIVERY INSPECTION (PDI). Recommended inflation pressure is not the pressure printed on tire sidewall.

^ Tires may be over-inflated from the assembly plant due to the mounting process.

^ Generally a 5.6°C (10°F) temperature change will result in (is equivalent to) a 6.9 kPa (1 psi) tire pressure change.

^ 2008-2009 HUMMER H2 Only - The H2 comes standard with Light Truck "D" Load Range tires with a recommended cold inflation
pressure of 289 kPa (42 psi). These tires will alert the driver to a low pressure situation at roughly 262 kPa (38 psi) due to a requirement in
FMVSS 138 which specifies a Minimum Activation Pressure for each tire type. This creates a relatively narrow window of "usable"
pressure values and the warning will be more sensitive to outside temperature changes during the colder months. As with other cold
temperature/tire pressure issues, there is nothing wrong with the system itself. If a vehicle is brought in with this concern, check for tire
damage and set all tires to the Recommended Cold Inflation Pressure shown on the vehicle placard.

Accurate tire pressures ensure the safe handling and appropriate ride characteristics of GM cars and trucks. It is critical that the tire pressure be
adjusted to the specifications on the vehicle¡Çs tire placard during PDI.

Ride, handling and road noise concerns may be caused by improperly adjusted tire pressure.

The first step in the diagnosis of these concerns is to verify that the tires are inflated to the correct pressures. The recommended tire inflation
pressure is listed on the vehicle¡Çs tire placard. The tire placard is located on the driver¡Çs side front or rear door edge, center pillar, or the rear
compartment lid.

Tip

^ Generally a 5.6°C (10°F) temperature increase will result in (is equivalent to) a 6.9 kPa (1 psi) tire pressure increase.

^ The definition of a "cold" tire is one that has been sitting for at least 3 hours, or driven no more than 1.6 km (1 mi).

^ On extremely cold days, if the vehicle has been indoors, it may be necessary to compensate for the low external temperature by adding
additional air to the tire during PDI.

^ During cold weather, the Tire Pressure Monitor (TPM) indicator light (a yellow horseshoe with an exclamation point) may illuminate. If this
indicator turns off after the tires warm up (reach operating temperature), the tire pressure should be reset to placard pressure at the cold
temperature.

^ The TPM system will work correctly with nitrogen in tires.

^ The TPM system is compatible with the GM Vehicle Care Tire Sealant but may not be with other commercially available sealants.

Important:
^ Do not use the tire pressure indicated on the tire itself as a guide.

^ Always inspect and adjust the pressure when the tires are cold.

^ Vehicles that have different pressures for the front and the rear need to be adjusted after tire rotation.
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 532
Chevrolet Venture V6-3.4L VIN E 2857

Improper tire inflation may result in any or all of the following conditions:

^ Premature tire wear

^ Harsh ride

^ Excessive road noise

^ Poor handling

^ Reduced fuel economy

^ Low Tire Pressure Monitor (TPM) Light ON

^ Low Tire Pressure Message on the Drivers Information Center (DIC)

Disclaimer

Technical Service Bulletin # 04-07-30-017B Date: 081125

A/T - Revised Converter Check Valve/Cooler Line Fitting


INFORMATION

Bulletin No.: 04-07-30-017B

Date: November 25, 2008

Subject:
Information on 4T65-E MN7, M15, M76, MN3 Automatic Transmission Case, Cooler Fitting and Torque Converter Drain Back Check Ball
Change

Models:
2008 and Prior GM Passenger Cars and Light Duty Trucks

with one of the HYDRA-MATIC(R) Automatic Transmissions shown above.

Supercede:

This bulletin is being revised to update the Parts Information. Please discard Corporate Bulletin Number 04-07-30-017A (Section 07 -
Transmission/Transaxle).
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 533
Chevrolet Venture V6-3.4L VIN E 2858

Effective with Julian date 4019 (January 19, 2004), the 4T65E transaxle cases and cooler fittings have changed and are not interchangeable with
past models. The technician may find that when replacing the inlet or outlet transmission cooler lines, the new lines cannot be connected to the
transmission.

A change to the transmission cooler line fittings was implemented in production on February 1, 2004. The cooler line fittings were changed to a
design with a longer lead in pilot (1). The cooler line fittings with the longer lead in pilot will not fit on models built before February 1, 2004.

The longer lead in pilot fittings (1) (9/16-18 UNF) have replaced the shorter lead in pilot fittings (2) (3/8-18 NPSF w/check ball & 1/4-18 NPSF).

If the transmission cooler lines will not connect, then replace them with the following cooler line fittings as appropriate with the older, shorter lead
in pilot design:

^ For vehicles built prior to February 1, 2004, use Transmission Fluid Cooler Inlet Hose, P/N 20793004.

^ For vehicles built after February 1, 2004, use Transmission Fluid Cooler Inlet Hose, second design P/N 15264588.

^ For vehicles built prior to February 1, 2004, use Transmission Fluid Cooler Outlet Hose, P/N 20793005.

^ For vehicles built after February 1, 2004, use Transmission Fluid Cooler Outlet Hose, second design P/N 15264589.

The torque specification has changed for the fittings to case. The torque has changed from 38 Nm (28 lb ft) to 32 Nm (23 lb ft).

Tighten

Tighten the new cooler fittings to 32 Nm (23 lb ft).


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 534
Chevrolet Venture V6-3.4L VIN E 2859

The converter drain back check ball (420C) has been removed from the cooler line fitting and is now located in the channel plate.

If you get a concern of no movement in the morning or after sitting for several hours, the cooler check ball should be inspected.

The best way to determine where the check ball is located is to look at the cooler line fittings. The old fittings are different sizes (3/8-18 NPSF &
1/4-18 NPSF) and would contain the cooler check ball. The new fittings are the same size as each other (9/16-18 UNF) and do not have a cooler
check ball.

Parts Information

Disclaimer

Technical Service Bulletin # 07-08-98-001A Date: 090128

Body - Non-Approval of Clipping For Collision Repair


INFORMATION

Bulletin No.: 07-08-98-001A

Date: January 28, 2009

Subject:
Non-approval of "Clipping" (Sectioning of Two Vehicles) For Collision Repair

Models:
2000-2010 GM Passenger Cars and Trucks (Including Saturn and Saab)
2003-2010 HUMMER H2, H3, H3T
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 535
Chevrolet Venture V6-3.4L VIN E 2860

Supercede:

This bulletin is being revised to add model years through 2010. Please discard Corporate Bulletin Number 07-08-98-001 (Section 08 - Body and
Accessories).

General Motors does not approve the use of "clipping" to repair collision damage to vehicles. In the collision repair industry, "clipping" refers to
cutting two damaged vehicles through the windshield pillars, the rocker panels, and across the floor pan and joining the undamaged portions from
these vehicles to make the repair.

The use of "clipping" voids GM's New Vehicle Limited Warranty (and any variety of the GM Protection Plan, as well as GM's new vehicle service
part and corrosion warranties) for each part in the clip.

GM does not sanction clipping repair because it cuts across the major load-bearing paths of a vehicle and can reduce the structural integrity of the
repaired vehicle. This is extremely critical because of the increase in the use of Advance High Strength Steel (AHSS). Improper repairs can lead to
vehicle performance issues related to noise, vibration and handling problems.

GM recommends replacing body components at factory seams. When applicable, GM will provide a specific service part for collision repair frames,
or provide repair information on how to create specific parts from a complete service assembly. Frame repair procedures for select GM vehicles are
available at http://www.goodwrench.com/gmgoodwrenchjsp/gmspo/techrepair_index.jsp. These parts and procedures provide a practical and
cost-effective alternative to clipping. GM provides vehicle specific collision repair procedures which are developed to be in a location and fashion
that will yield panel strength comparable to the original panel strength. Replacing damaged parts of a vehicle designed to crush in a collision may
reduce occupant protection in a future collision.

GM has not tested or validated a "clipped vehicle" repair; therefore, GM cannot endorse this type of repair or confirm the crash performance during
a subsequent collision. GM recommends the use of genuine GM parts in repairs to help ensure the vehicle is returned to pre-collision condition.

DisclaimerTechnical Service Bulletin # 01-07-30-036H Date: 090129

A/T Control - DTC P0756 Diagnostic Tips


INFORMATION

Bulletin No.: 01-07-30-036H

Date: January 29, 2009

Subject:
Diagnostic Tips for Automatic Transmission DTC P0756, Second, Third, Fourth Gear Start

Models:
2009 and Prior GM Passenger Cars and Light Duty Trucks
2009 and Prior HUMMER H2, H3
2009 and Prior Saab 9-7X

with 4L60-E, 4L65-E or 4L70E Automatic Transmission (RPOs M30, M32 or M70)

Supercede:

This bulletin is being revised to add the 2009 model year and add details regarding spacer plates. Please discard Corporate Bulletin Number
01-07-30-036G (Section 07 - Transmission/Transaxle).

Some dealership technicians may have difficulty diagnosing DTC P0756, 2-3 Shift Valve Performance on 4L60-E, 4L65-E or 4L70E automatic
transmissions. As detailed in the Service Manual, when the PCM detects a 4-3-3-4 shift pattern, DTC P0756 will set. Some customers may also
describe a condition of a second, third or fourth gear start that may have the same causes but has not set this DTC yet. Below are some tips when
diagnosing this DTC:

^ This is a performance code. This means that a mechanical malfunction exists.

^ This code is not set by electrical issues such as a damaged wiring harness or poor electrical connections. Electrical problems would cause a
DTC P0758, P0787 or P0788 to set.

^ The most likely cause is chips/debris plugging the filtered AFL oil at orifice # 29 on the top of the spacer plate (48). This is a very small hole
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 536
Chevrolet Venture V6-3.4L VIN E 2861
and is easily plugged by a small amount of debris. It is important to remove the spacer plate and inspect orifice # 29 and the immediate area for
the presence of chips/debris. Also, the transmission case passage directly above this orifice and the valve body passage directly below should be
inspected and cleaned of any chips/debris. For 2003 and newer vehicles the spacer plate should be replaced. The service replacement spacer
plate is a bonded style with gaskets and solenoid filter screens bonded to the spacer plate. These screens can help to prevent plugging of orifice
# 29 caused by small debris or chips.

^ This code could be set if the 2-3 shift valve (368) were stuck or hung-up in its bore. Inspect the 2-3 shift valve (368) and the 2-3 shuttle valve
(369) for free movement or damage and clean the valves, the bore and the valve body passages.

^ This code could be set by a 2-3 shift solenoid (367b) if it were cracked, broken or leaking. Refer to Shift Solenoid Leak Test in the appropriate
Service Manual for the leak test procedure. Based on parts return findings, a damaged or leaking shift solenoid is the least likely cause of this
condition. Simply replacing a shift solenoid will not correct this condition unless the solenoid has been found to be cracked, broken or leaking.

It is important to also refer to the appropriate Service Manual or Service Information (SI) for further possible causes of this condition.

Disclaimer

Technical Service Bulletin # 07-08-64-022B Date: 090106

Instruments - Unnecessary Park Assist Mirror Replacement


INFORMATION

Bulletin No.: 07-08-64-022B

Date: January 06, 2009

Subject:
Information On Curb Park Assist And Memory Related Issues On Outside Rearview Mirrors

Models:
2008 and Prior GM Passenger Cars and Trucks (Including Saturn) (Excludes Cadillac SRX)
2008 and Prior HUMMER H2, H3
2007 and Prior Saab 9-7X
with Memory Mirrors

Supercede:

This bulletin is being revised to indicate that technicians should reprogram the driver's side door module for a memory or curb park assist issue.
Please discard Corporate Bulletin Number 07-08-64-022A (Section 08 - Body and Accessories).

A large number of mirrors are being returned through the Warranty Parts Center (WPC) with customer comments of curb park assist and memory
setting issues. Returned part analysis indicates that the mirrors are found to be fully functional. If you have a memory or curb park assist issue,
check the wiring, the respective door module and reprogram the driver's door module with the latest software in TIS.

Disclaimer
Technical Service Bulletin # 08089C Date: 081118

Campaign - Deactivation Of Analog OnStar(R)


# 08089C: Special Coverage Adjustment - Analog OnStar Deactivation
(Nov 18, 2008)

Subject:
08089C -- SPECIAL COVERAGE ADJUSTMENT - ANALOG ONSTAR(R) DEACTIVATION
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 537
Chevrolet Venture V6-3.4L VIN E 2862
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 538
Chevrolet Venture V6-3.4L VIN E 2863

Models

The service procedure in this bulletin has been revised. Step 11 in the procedure for the 2004-2005 Saab 9-3 (9440) Convertible has been revised.
Discard all copies of bulletin 08089B, issued September 2008.

Condition

In November 2002, the U.S. Federal Commissions (FCC) ruled that wireless carriers would no longer be required to support the analog wireless
network beginning in 2008. As a result, On Star(R) is unable to continue analog service.

OnStar(R) has deactivated most of the systems operating in the analog mode; however, there are some vehicles that OnStar(R) could not deactivate.
Although the analog OnStar(R) hardware in these vehicles can no longer communicate with OnStar(R), the hardware in the vehicle is still active. If
the OnStar(R) emergency button is pressed, or in the case of an airbag deployment, or near deployment, the customer may hear a recording that
OnStar(R) is being contacted. However, since analog service is no longer available, the call will not connect to OnStar(R). To end the call, the
customer must press the white phone or white dot button. If the call is not ended, the system will continue to try to connect to OnStar(R) until the
vehicle battery is drained.

Special Policy Adjustment

At the customer's request, dealers/retailers are to deactivate the OnStar(R) system. The service will be made at no charge to the customer.

This special coverage covers the condition described above until December 31, 2008 for all non-Saab vehicles; April 30, 2009 for all Saab vehicles.

Vehicles Involved
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 539
Chevrolet Venture V6-3.4L VIN E 2864
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 540
Chevrolet Venture V6-3.4L VIN E 2865
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 541
Chevrolet Venture V6-3.4L VIN E 2866
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 542
Chevrolet Venture V6-3.4L VIN E 2867
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 543
Chevrolet Venture V6-3.4L VIN E 2868
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 544
Chevrolet Venture V6-3.4L VIN E 2869
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 545
Chevrolet Venture V6-3.4L VIN E 2870
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 546
Chevrolet Venture V6-3.4L VIN E 2871
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 547
Chevrolet Venture V6-3.4L VIN E 2872
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 548
Chevrolet Venture V6-3.4L VIN E 2873

Involved are certain vehicles within the VIN breakpoints shown above.

PARTS INFORMATION -- Saab US Only

Customer Notification

General Motors will notify customers of this special coverage on their vehicles (see copy of typical customer letter shown in this bulletin - actual
divisional letter may vary slightly).
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 549
Chevrolet Venture V6-3.4L VIN E 2874
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 550
Chevrolet Venture V6-3.4L VIN E 2875
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 551
Chevrolet Venture V6-3.4L VIN E 2876

Claim Information - GM, Saturn Canada and Saab Canada Only

Claim Information - Saturn US Only

Customer Reimbursement Claims - Special Attention Required

Customer reimbursement claims must have entered into the "technician comments" field the CSO # (if repair was completed at a Saturn Retail
Facility) date, mileage, customer name, and any deductibles and taxes paid by the customer.

Claim Information - Saab US Only


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 552
Chevrolet Venture V6-3.4L VIN E 2877

1. To receive credit, submit a claim with the information above.

Disclaimer

2001 and Older Model Year Vehicles (Except Saab Vehicles)


2001 and Older Model Year Vehicles (Except Saab Vehicles)

Important:
2001 and older model year vehicles require the removal of the battery power from the OnStar(R) vehicle interface unit (VIU) to eliminate
the possibility of an inadvertent OnStar(R) or emergency/airbag call.

1. Locate and gain access to the OnStar® VIU. Refer to OnStar Vehicle Interface Unit Replacement in SI.

Important:
Complete removal of the VIU is usually not required. Perform only the steps required to gain access to the C2 32-way blue connector.
Residing in the C2 connector are the battery positive (+) circuits. Removal of the C2 connector will deactivate the unit and eliminate the
possibility of an inadvertent OnStar(R) or emergency/airbag call.

2. Disconnect the C2 32-way blue connector from the VIU and tape the connector to a secure location. Refer to Cellular Communications
Connector End Views and related schematics in SI, if required.

Important:
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 553
Chevrolet Venture V6-3.4L VIN E 2878
DO NOT perform the OnStar(R) reconfiguration and/or programming procedure.

3. Secure the VIU in its original brackets and/or mounting locations and reinstall the VIU and interior components that were removed to gain
access to the VIU. Refer to OnStar Vehicle Interface Unit Replacement in SI.

2002 Through 2006 Model Year Vehicles (Except Saab Vehicles)


2002 through 2006 Model Year Vehicles (Except Saab Vehicles)

Important:
The Tech 2 diagnostic tool must be updated with version 28.002 or later in order to successfully perform the VCIM setup procedure and
disable the analog system.

1. Connect the Tech 2 to the data link connector (DLC), which is located under the instrument panel of the vehicle.

2. Turn the Tech 2 ON by pressing the power button.

Important:
Tech 2 screen navigation to get to the setup procedure depends on the year and make of the vehicle. The actual name of the setup
procedure (Setup New OnStar or VCIM Setup) depends on model year and vehicle make as well. Example Tech 2 navigation to the setup
procedure Tech 2 screen is provided below.

^ Diagnostics >> (2) 2002 >> Passenger Car >> Body >> C >> OnStar >> Special Functions >> Setup New OnStar >>

^ Diagnostics >> (5) 2005 >> Passenger Car >> (4) Buick >> C >> Body >> Vehicle Comm. Interface Module >> Module Setup >>
VCIM Setup >>

3. Setup VCIM using the Tech 2. Follow on-screen instructions when you have reached the setup Tech 2 screen.

2000-2002 Saab 9-3 (9400) 4D/5D; 2000-2003 Saab 9-3 (9400) CV


2000-2002 Saab 9-3 (9400) 4D/5D; 2000-2003 Saab 9-3 (9400) CV

1. Remove the ground cable from the battery's negative terminal.

2. Apply the handbrake brake.

3. Detach the floor console.

4. Remove the switch and the floor console:

3.1. Twist loose the immobilizer unit (A), bayonet fitting. Unplug the unit's connector.

3.2. Remove the ignition switch cover (B) by first undoing the rear edge of the cover and then unhooking the front edge. Unplug the
ignition switch lighting connector.

3.3. Undo the floor console's retaining bolts (C).

3.4. Take out the rear ashtray/cover (D).

3.5. Remove the screw (E) for the rear cover.

3.6. Remove the floor console's retaining nuts (E).


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 554
Chevrolet Venture V6-3.4L VIN E 2879

3.7. Detach the floor console (G) by pulling it straight back and lifting it slightly.

3.8. If required, detach the switch for the rear seat heater and unplug the connector.

4. Remove the switch and the floor console:

4.1. Detach the window lift module (A) by loosening it in the front edge (snap fastener). Unplug the window lift module's connector.

4.2. Detach the switch for the roof lighting (B) and unplug its connector. Lift away the floor console.

5. Pry out the signal line from the SRS control module to the OnStar(R) control module and secure it:

5.1. Unplug the SRS control module's connector (A).

5.2 Cut off the cable tie (B), detach the connector's rear end face (C) and pull out the connecting rail (D).
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 555
Chevrolet Venture V6-3.4L VIN E 2880

5.3. Remove pin 39, cut off the cable terminal and insulate the end with tape (E). Fold back the cable and secure it with tape (F).

5.4. Fit the connecting rail and end face.

5.5. Plug in the connector (A) and secure the cables with cable ties (B).

6. Install the floor console over the handbrake. Do not press the console down into place, but instead allow it to fit loosely.

7. Install the switch:

7.1. Install the switch for the roof lighting (B) and plug in its connector.

7.2. Guide the connectors for the window lift module and rear seat heater, if equipped, through the hole for each respective unit. Plug in the
window lift module's connector and install the module (A).

7.3. If equipped, connect the rear seat heater's connector and install the switch.

8. Install the floor console:


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 556
Chevrolet Venture V6-3.4L VIN E 2881

8.1. Install the floor console's retaining bolts (C) and retaining nuts (F).

8.2. Align the rear cover; make sure that the air duct connects firmly to the air nozzle. Screw in the cover (E).

8.3. Install the ashtray/cover (D).

8.4. Install the ignition switch cover (B).

8.5. Plug in the immobilizer unit (A) connector. Install the unit, bayonet fitting.

9. Remove the OnStar(R) control modules and secure the wiring:

9.1. Remove the right-hand rear luggage compartment trim in accordance with WIS - 8.

Body - Interior equipment - Adjustment/Replacement.

9.2. Unplug the connectors (A) from the OnStar(R) control modules.

9.3. Remove the console (B) together with the OnStar(R) control modules.

Important:
Secure the wiring harness so that there is no risk of chafing and rattling.

9.4. Fold back the wiring harness and tape over the connectors (C). Fold back the wiring harness once more and secure with cable ties (D).

9.5. Install the right-hand rear luggage compartment in accordance with WIS - 8. Body - Interior equipment - Adjustment/Replacement.

10. Install the ground cable to the battery's negative terminal.

11. Clear the diagnostic trouble codes.

12. Set the date and time, see WIS - 3. Electrical system - Information display (SID_ - Technical description.
2003-2005 Saab 9-3 (9400) 4D/5D; 2004-2005 Saab 9-3 (9400) CV
2003-2005 Saab 9-3 (9440) 4D/5D; 2004-2005 Saab 9-3 (9440) CV

Notice:
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 557
Chevrolet Venture V6-3.4L VIN E 2882
Handle the fiber optic cables with care or the signal may be distorted.

^ It is very important that the two leads in the connector are not confused with one another.

^ Do not splice the cables.

^ Do not bend the cable in a radius smaller than 25 mm (1 in).

^ Do not expose the cable to temperatures exceeding 185°F (85°C).

^ Keep the cable ends free from dirt and grime.

^ Do not expose the cable to impact as this may cause the transparent plastic to whiten, thereby reducing the intensity of the light and
causing possible communication interruptions.

^ The cable should not lie against any sharp edges as this may cause increased signal attenuation.

1. Remove the ECU CU with a Tech 2(R) according to the following: Fault diagnosis - Select model year - Select Saab 9-3 Sport (9440) - All -
Add/Remove - Control Module - CU/PU - Remove.

2. Remove the ground cable from the battery's negative terminal.

3. Remove the floor console in accordance with WIS - 8. Body - Interior equipment - Adjustment/Replacement.

4. Pry out the signal line from the SRS control module to the OnStar(R) control module and secure it:

4.1. Unplug the SRS control module's connector (A).

4.2. Cut off the cable tie (B), detach the connector's rear end face (C), and pull out the connecting rail (D).
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 558
Chevrolet Venture V6-3.4L VIN E 2883

4.3. Extract pin 15, cut off the cable terminal and insulate the end with tape (E). Fold back the cable and secure it with tape (F).

4.4. Fit the connecting rail and end face.

4.5. Plug in the connector (A) and secure the cables with cable ties (B).

5. Remove the parcel shelf trim in accordance with WIS - 8. Body - Interior equipment - Adjustment/Replacement.

6. M03: Replace the optic cable on the right-hand side

Important:
Secure the wiring harness so that there is no risk of chafing or rattling.

6.1. Remove the passenger seat in accordance with WIS 8. Body - Seats - Adjustment/Replacement.

6.2. Remove the right-hand B-pillar trim in accordance with WIS - 8. Body - Interior equipment - Adjustment/Replacement.

6.3. Remove the right-hand C pillar trim in accordance with WIS - 8. Body - Interior equipment - Adjustment/Replacement.

6.4. Fold the rear seat backrest forward.

6.5. Remove the right-hand side bolster in accordance with WIS - 8. Body - Seats - Adjustment/Replacement.

6.6. Remove the A-pillar's lower side piece.

6.7. Open the cover on the right-hand wiring harness channels.

6.8. Loosen the locking strip (A) on the 2-pin connector (H2-11) for the optic cable, located by the right-hand A-pillar.

6.9. Loosen the catch (B) and remove the optic cable that runs backward in the car.

6.10. Dismantle the end cap from the new optic cable (12 783 577) and connect it to the connector H2-11. Push in the optic cable and make
sure the catch (B) locks and refit the locking strip (A).
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 559
Chevrolet Venture V6-3.4L VIN E 2884

6.11. Secure the connector and the old optic cable using the cable tie for the existing wiring harness (C).

Important:
The optic cable must not be bent with a radius less than 25 mm (1 in).

6.12. Place the optic cable in the wiring harness channels on the right-hand side. Thread through the existing cable ties (C) if possible,
otherwise, secure with a cable tie to the existing one. Close the cover on the channels. Ensure the catches lock.

6.13. Secure the optic cable along the right-hand rear wheel housing, next to the ordinary wiring harness securing points and by the SRS unit
(D).

6.14. Thread the optic cable up next to the safety belt by the old optic cable and place on the parcel shelf.

6.15. Unplug the connectors (E) from the OnStar(R) control modules.
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 560
Chevrolet Venture V6-3.4L VIN E 2885

6.16. Remove the console (F) together with the OnStar(R) control modules.

Important:
The optic cable must not be bent with a radius less than 25 mm (1 in).

6.17. Fold back the wiring harness and tape over the connectors (G). Fold back the wiring harness once more and secure with cable ties (H).

6.18. Secure the new optic cable on the parcel shelf along the existing wiring harness by the ordinary securing points and by the speaker (I).

6.19. Thread the optic cable down next to the old cable from the parcel shelf to the left-hand wheel housing, next to REC. The cable is
secured in the existing clips.

6.20. Fit the right-hand C-pillar trim in accordance with WIS - 8. Body - Interior equipment - Adjustment/Replacement.

6.21. Fit the parcel shelf trim in accordance with WIS - 8. Body - Interior equipment - Adjustment/Replacement.

6.22. Fit the passenger seat in accordance with WIS - 8. Body - Seats - Adjustment/Replacement.

6.23. Fit the right-hand side bolster in accordance with WIS - 8. Body - Seats - Adjustment/Replacement.

6.24. Fold up the rear seat backrest.

6.25. Fit the right-hand B-pillar trim in accordance with WIS - 8. Body - Interior equipment - Adjustment/Replacement.

6.26. Fit the A-pillar's lower side piece.

7. M04-05, 4D: Removing the OnStar® control modules and securing the wiring:
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 561
Chevrolet Venture V6-3.4L VIN E 2886

7.1. Remove the console (A) together with the OnStar(R) control modules.

7.2. Remove the connectors (B).

Important:
The optic cable must not be bent with a radius less than 25 mm (1 in).

Important:
Secure the wiring harness so that there is no risk of chafing and rattling.

7.3. Fold back the wiring harness and tape over the connectors (C). Fold back the wiring harness once more and secure with cable ties (D).

7.4. Fit the parcel shelf trim in accordance with WIS - 8. Body - Interior equipment - Adjustment/Replacement.

8. CV: Removing the OnStar(R) control modules and securing the wiring: Adjustment/Replacement.

8.1. Open the luggage compartment floor.


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 562
Chevrolet Venture V6-3.4L VIN E 2887

8.2. Remove the console (A) together with the OnStar(R) control modules.

8.3. Remove the connectors (B).

Important:
The optic cable must not be bent with a radius less than 25 mm (1 in).

Important:
Secure the wiring harness so that there is no risk of chafing and rattling.

8.4. Fold back the wiring harness and tape over the connectors (C). Fold back the wiring harness once more and secure with cable ties (D).

8.5. Close the luggage compartment floor.

9. Fold down the left-hand rear side hatch in the luggage compartment.
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 563
Chevrolet Venture V6-3.4L VIN E 2888

10. M03: Replace the optic cable on the left-hand rear side:

10.1. Place the optic cable so that it is positioned behind the terminal housing on top of REC (A).

10.2. Remove the locking strip (B) on the 2-pin connector (H2-9) for the optic cable.

10.3. Open the terminal housing (C) with a screwdriver. Remove the secondary catch (D) on the connector and disconnect the optic cable
coming from the OnStar(R) control modules.

10.4. Remove the end cap from the new optic cable, connect to the connector and refit the secondary catch (D). Fit the terminal housing (C)
to the connector and refit the locking strip (B).
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 564
Chevrolet Venture V6-3.4L VIN E 2889

10.5. Secure the old optic cable together with the new one (E).

Important:
The optic cable must not be bent with a radius less than 25 mm (1 in).

Important:
Secure the wiring harness so that there is no risk of chafing and rattling.

11. CV: Remove the rear seat in accordance with WIS - 8. Body - Interior equipment - Adjustment/Replacement. The O-bus connector H2-9 is
located behind the left speaker.

12. M04-05: Disconnect the optic cables on the OnStar(R) control modules and join the cables:

12.1. Cut off the cable tie holding the connector (H2-9) against REC.

12.2. Cars with brackets for e.g. an amplifier: Remove the pin strap (A) from the bracket and remove the tape (B) holding the optic cables.
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 565
Chevrolet Venture V6-3.4L VIN E 2890

12.3. Remove the locking strip (C) on the 2-pin connector (H2-9). Open the terminal housing with a screwdriver. Remove the secondary
catch (E) on the connector and remove the optic cables coming from the OnStar(R) control modules.

12.4. Loosen one of the optic cables remaining in H2-9 (F), connect it to the connector and fit the secondary catch (E). Connect the
connector so that the optic cables are opposite each other (G). Connect the terminal housing (D) and refit the locking strip (C).

Important:
The optic cable must not be bent with a radius less than 25 mm (1 in).

12.5. Cars with brackets for e.g. an amplifier: Fit the cable tie (11 900 515) to the wiring harness approx. 100 mm (4 in) from H2-9, fit the
cable tie (H) to the bracket. Gather the optic cable in a gentle loop (I) and then place the loop behind the bracket.
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 566
Chevrolet Venture V6-3.4L VIN E 2891

Important:
The optic cable must not be bent with a radius less than 25 mm (1 in).

12.6. Cars without brackets for e.g. an amplifier: Gather the optic cable in a gentle loop (J) and secure with cable tie.

13. CV: Fit the left-hand, rear side hatch trim in accordance with WIS - 8. Body - Interior equipment - Adjustment/Replacement.

14. Fit the ground cable to the battery's negative terminal.

15. Carry out procedures after disconnecting the battery, see WIS - 3. Electrical System - Charging system - Adjustment/Replacement.

Important:
Follow Tech 2(R) on-screen instructions.

16. Add ECU ICM, choose without OnStar(R). See WIS-General-Tech 2(R) - Description and Operation - Add/Remove.

2000-2004 Saab 9-5


2000-2004 Saab 9-5

1. Remove the ground cable from the battery's negative cable.

2. Remove the center console, see WIS - Body - Interior.

3. Loosen the gear shift housing (A).

AUT: Disconnect the 6-pin connector (B) to improve access to the gear shift housing screws.

4. Disconnect the signal cable from the SRS control module to the OnStar(R) control module and secure the cable.
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 567
Chevrolet Venture V6-3.4L VIN E 2892

4.1. Disconnect the connector (A) from the SRS control module and cut the cable tie (B).

4.2. Release the back end of the connector (C) and remove from the contact rail (D).

4.3. M00-01: Disconnect pin 39, cut off the cable terminal and insulate the end using tape (E). Fold back the cable and secure using tape
(F).

4.4. M02-04: Disconnect pin 58, cut off the cable terminal and insulate the end using tape (E). Fold back the cable and secure using tape
(F).

4.5. Assemble the contact rail and end.

4.6. Connect connector (A) and secure the cable using a cable tie (B).
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 568
Chevrolet Venture V6-3.4L VIN E 2893

5. Assemble the gear shift housing (A).

AUT: Connect connector (B).

6. Assemble the center console, see WIS - Body - Interior.

7. Remove the OnStar(R) control module and secure the cable harness:

7.1. 5D: Remove the right-hand cover from the luggage compartment floor.

7.2. Remove the console (A).

7.3. Disconnect the connector (B) from the OnStar(R) control module.
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 569
Chevrolet Venture V6-3.4L VIN E 2894

Important:
Secure the cable harness to prevent the risk of scraping and rattling.

7.4. Fold back the cable harness and tape down the connector (C). Fold back the cable harness again and secure with cable ties (D).

7.5. 5D: Assemble the right-hand cover for the luggage compartment floor.

8. Fit the ground cable on the battery's negative cable.

9. Erase the diagnostic trouble codes.

10. Set the date and time, see WIS - 3. Electrical system - Information display (SID) - Technical description.

Technical Service Bulletin # 02-08-98-002C Date: 090203

Body - Hem Flange Rust Repair Information


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 570
Chevrolet Venture V6-3.4L VIN E 2895
INFORMATION

Bulletin No.: 02-08-98-002C

Date: February 03, 2009

Subject:
Hem Flange Rust Repair

Models:
2009 and Prior Passenger Cars and Trucks (Including Saturn)
2009 and Prior HUMMER H2, H3
2009 and Prior Saab 9-7X

Supercede:

This bulletin is being revised to add the 2009 model year and revise the Approved Refinish Materials booklet. Please discard Corporate Bulletin
Number 02-08-98-002B (Section 08 - Body and Accessories).

In the event that hem flange corrosion becomes a concern, a new tool has been released by Kent Moore, J 46162, which allows for easier opening
of the hem flange.

Repair Procedure

1. Remove the body panel from the vehicle.

2. Clean the hem flange area with wax and grease remover.

3. Using Kit J 46162, insert the tool into an air impact gun and open the hem flange up starting at one end.

4. Clean out the corrosion by "sand blasting" or by using *3M(R) Strip Disc, P/N 07460.

Important:

If perforation is present, replace the affected panel.

5. Inspect the area for rust perforation or "micro pin holes".

6. Apply anticorrosion primer to the hem flange.

7. Apply a bead of *LORD FUSOR, P/N 108B or 109B, adhesive to the hem flange. Follow the manufacturer's recommendations for use.

8. Close the hem flange using the tool in the kit.

9. Clean off excessive adhesive from the repair area.

Important:

Refer to the 2009 GM Approved Refinish Materials booklet (GMW-15406) for specific products.To access the booklet, go to
www.gmgoodwrench.com. Click on For Body Shops & Service at the bottom of the page. Then click on GM Collision Parts. From this page, select
Collision Technical Repair Information. Finally, select Paint Shop.

10. Prime and refinish the area as required.

*We believe these sources and their products to be reliable. There may be additional manufacturers of such material. General Motors does not
endorse, indicate any preference for or assume any responsibility for the products from these firms or for any such items which may be available
from other sources.

Parts Information

To order this tool (J 46162), call Kent Moore at 1-800-GMTOOLS. LORD FUSOR and 3M(R) Strip Disc may be obtained from your local body
shop supplier.
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 571
Chevrolet Venture V6-3.4L VIN E 2896

DisclaimerTechnical Service Bulletin # 09-08-48-002A Date: 090319

Body - Marks/Stains on Windshield When Wet


TECHNICAL

Bulletin No.: 09-08-48-002A

Date: March 19, 2009

Subject:
Marks/Stains on Windshield When Wet (Clean Windshield)

Models:
2010 and Prior Passenger Cars and Trucks (Including Saturn and Saab)
2010 and Prior HUMMER H2, H3

Supercede:
This bulletin is being revised to update the models and model years. Please discard Corporate Bulletin Number 09-08-48-002 (Section 08 - Body
and Accessories).

Condition

Some owners may comment that marks/stains appear on the windshield when the windshield is wet.

Cause

This condition may be caused by contact between the windshield and the vacuum hoses or other tools used in the assembly process. This contact
may leave a residue that creates a water repellent surface on the glass which, in wet conditions, appear as marks/stains on the surface.

Correction

Important
DO NOT REPLACE THE WINDSHIELD FOR THIS CONDITION.

To clean the windshield, use Eastwood Glass Polishing Compound*. Follow the manufacturer's directions for product use. Use only hand tools. DO
NOT USE POWER TOOLS.

Parts Information

Eastwood Glass Polishing Compound

1-800-343-9353 (for overseas inquiries: +1-610-705-2200)

http://www.eastwoodco.com/

*We believe this source and their products to be reliable. There may be additional manufacturers of such products. General Motors does not
endorse, indicate any preference for or assume any responsibility for the products from this firm or for any such items which may be available from
other sources.

Warranty Information

For vehicles repaired under warranty, use the table above.

Disclaimer

Technical Service Bulletin # 08-03-10-005A Date: 090331


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 572
Chevrolet Venture V6-3.4L VIN E 2897

Wheels/Tires - Chrome/Steel Valve Stem Cap Precautions


INFORMATION

Bulletin No.: 08-03-10-005A

Date: March 31, 2009

Subject:
Use of Chrome or Chrome Plated Steel Valve Caps on Aluminum Valve Stems

Models:
2010 and Prior GM Passenger Cars and Light Duty Trucks (including Saturn)
2010 and Prior HUMMER H2, H3
2009 and Prior Saab 9-7X

Supercede:
This bulletin is being revised to include the 2010 model year. Please discard Corporate Bulletin Number 08-03-10-005 (Section 03 - Suspension).

This bulletin is being issued to inform dealers about the use of chrome or chrome-plated steel valve caps on aluminum valve systems.

Dealers/customers cannot install a chrome or chrome-plated steel valve cap on an aluminum valve system. If this happens, the contact between the
different metals results in galvanic corrosion, which will seize the cap to the stem and may fracture the stem when attempting to remove the cap.

Inform customers of corrosion issues when chrome or chrome-plated steel valve caps are used on aluminum valve stems.

Use only plastic or aluminum caps with aluminum valve systems.

Technical Service Bulletin # 09-09-40-001 Date: 090217

Restraints - Seat Belt Warning Lamp On/Buckling Issues


INFORMATION

Bulletin No.: 09-09-40-001

Date: February 17, 2009

Subject:
Seat Belt Buckle Latching Issues and/or Seat Belt Warning Lights Illuminated

Models:
2010 and Prior GM Passenger Cars and Trucks (Including Saturn)
2010 and Prior HUMMER H2, H3
2010 and Prior Saab 9-7 X

This bulletin is being published to advise dealers about seat belt buckles not operating and/or seat belt warning light illumination, as well as
difficulty latching and unlatching the buckle or the buckle release button sticking.

Analysis of warranty data has determined that this condition may be caused by sticky beverages being spilled onto or into the seat belt buckle
assembly. Foreign debris from food, candy wrappers, paper and coins can also contribute to this condition.

Important:

If foreign material (debris) or sticky liquids are the cause of the concern, show the customer the condition of the component (buckle assembly) and
explain how it is affecting the function of the restraint system. Strongly recommend that the component be replaced. Point out the fact that this is
not a manufacturing defect and is not covered by the new vehicle warranty. If the customer declines to have parts replaced, the service department
management must make a notation on the service record that the lack of functionality of seating position with an inoperative buckle was fully
explained to the customer. The service department management must advise the customer that having a non-functioning buckle in a seating position
voids ability to use that seating position (no one should ride in the seat). Also make the customer aware that it may be against the law to ride in a
vehicle without wearing a restraint system.

Important:

Never insert anything other than the seat belt latch plate into the buckle assembly. Do not attempt to dig anything out of a buckle with a tool. Never
try to wash out a buckle to remove a spilled liquid as this may damage the buckle.

Use the following steps to determine the cause of the concern.

1. Inspect the buckle assembly with a light shining on the latch plate insertion area. Look for any debris or foreign objects in the buckle.
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 573
Chevrolet Venture V6-3.4L VIN E 2898

2. If any debris or foreign objects are observed, try to vacuum out the item. After the foreign material is removed, latch and unlatch the seat belt. If
the system functions properly, do not replace the seat belt buckle assembly.

3. If the condition has not been corrected, inspect the buckle assembly for any sticky residue. If sticky residue is found, inform the customer that a
substance was spilled on the seat belt buckle assembly causing the malfunction. The buckle assembly will need to be replaced at the customer's
expense.

4. Refer to SI for seat belt component replacement.

Important:

If foreign material (debris) or sticky liquids are the cause of the concern, show the customer the condition of the component (buckle assembly) and
explain how it is affecting the function of the restraint system. Strongly recommend that the component be replaced at the customer's expense. Point
out the fact that this is not a manufacturing defect and is not covered by the new vehicle warranty. If the customer declines to have parts replaced,
the service department management must make a notation on the service record that the lack of functionality of seating position with an inoperative
buckle was fully explained to the customer. The service department management must advise customer that having a non-functioning buckle in a
seating position voids ability to use that seating position (no one should ride in the seat). Also make the customer aware that it may be against the
law to ride in a vehicle without wearing a restraint system.

5. If further restraint diagnosis is required, refer to Seat Belt System Operational and Functional Checks in SI.

DisclaimerTechnical Service Bulletin # 00-05-22-002L Date: 090326

Brakes- Disc Brake Warranty Service And Procedures


INFORMATION

Bulletin No.: 00-05-22-002L

Date: March 26, 2009

Subject:
Disc Brake Warranty Service and Procedures

Models:
1999-2010 GM Passenger Cars and Light Duty Trucks
2003-2010 HUMMER H2
2006-2010 HUMMER H3
1999-2004 Isuzu Light Duty Trucks (Canada Only)
2005-2009 Saab 9-7X (Canada Only)
1999-2010 Saturn Vehicles (Canada Only)

EXCLUDING 2009-2010 Chevrolet Corvette ZR1

Supercede:
This bulletin is being revised to inform you that due to improvements in vehicle brake corner and wheel design, assembly plant build processes and
dealership required tools like the On-Car Lathe, measuring for Lateral Run Out (LRO) is no longer a required step when performing base brake
service. Due to this change, you are no longer required to enter the LRO measurement on the repair order or in the warranty system failure code
section. The bulletin information below and the base brake labor operations have been updated accordingly. Due to this change it is more important
than ever to properly maintain your brake lathe (per the Brake Lathe Calibration Procedure in this bulletin). Please discard Corporate Bulletin
Number 00-05-22-002K (Section 05 - Brakes).

For your convenience, this bulletin updates and centralizes all GM's Standard Brake Service Procedures and Policy Guidelines for brake rotor and
brake pad service and wear. For additional information, the Service Technical College lists a complete index of available Brake courses. This
information can be accessed at www.gmtraining.com > resources > training materials > brakes courseware index. In Canada, refer to Service Know
How course 55040.00V and Hydraulic Brake Certification program 15003.16H.

Important

PLEASE FAMILIARIZE YOURSELF WITH THESE UPDATES BEFORE PERFORMING YOUR NEXT GM BRAKE SERVICE.

The following four (4) key steps are a summary of this bulletin and are REQUIRED in completing a successful brake service.
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 574
Chevrolet Venture V6-3.4L VIN E 2899

1. Measure and Document Pre-Service Rotor Thickness* (REQUIRED on Repair Order) - determine rotor clean-up/refinish/replace

2. Properly clean ALL brake corner mating surfaces - hub, rotor and wheel

3. Properly clean-up/refinish rotor, measure and document post-service rotor thickness (REQUIRED on Repair Order)

Important
If it is determined the rotor needs to be refinished, verify lathe equipment is properly calibrated.

4. Properly reassemble the brake corner using proper torque tools, torque specification and torque sequence - wheel lug nuts.

* The bulletin refers to Minimum Thickness specification as the minimum allowable thickness after refinish. Always refer to SI to verify the
spec stamped on the rotor is the minimum thickness spec after refinish and not the discard spec.

Bulletin Format

***REPAIR ORDER REQUIRED DOCUMENTATION


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 575
Chevrolet Venture V6-3.4L VIN E 2900

Important

When using any one of the brake labor operations listed in this bulletin (except for H9709 - Brake Burnish), the following two rotor measurements
(1. Original Rotor Thickness, 2. Refinished Rotor Thickness are required and MUST be written/documented on the repair order, or for your
convenience, complete the form (GM Brake Service Repair Order Documentation for Required Measurements) shown above and attach it to the
repair order. If the Warranty Parts Center generates a request, this Documentation/Form must be attached to the repair order that is sent back.

Important

Documentation of brake lathe maintenance and calibration as recommended by the lathe manufacturer must be available for review upon request.

Repair Order Documentation - Rotor Original And Refinished Thickness - REQUIRED

When resurfacing a brake rotor or drum, the ORIGINAL thickness (measured thickness before refinish) and REFINISHED thickness (measured
thickness after refinish) MUST be written/documented on the repair order hard copy for each rotor serviced. If a rotor replacement is necessary,
only the original thickness measurement needs to be recorded.

Repair Order Documentation - Explanation of Part Replacement - REQUIRED

If replacement of a brake component is necessary, proper documentation on the repair order is required. See the following examples:

^ Brake rotor replacement - Customer comment was brake pulsation. Rotor was refinished on a prior brake service. After rotor measurement, it
was determined that refinishing the rotor again would take it under the Minimum Thickness specification.

^ Brake pad replacement - Customer comment was brake squeak noise. On inspection, found pads contaminated by fluid leak at caliper.
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 576
Chevrolet Venture V6-3.4L VIN E 2901

TOOL INFORMATION

CORRECTION PLATE PART INFORMATION

Refer to TSB 01-05-23-001 for the Brake Align(R) application chart.

For vehicles repaired under warranty, Brake Align(R) Run-Out Correction Plates should be submitted in the Net Amount at cost plus 40%. Brake
Align(R) Run-Out Correction Plates are available through the following suppliers:

- Dealer Equipment and Services


- Brake Align(R) LLC (U.S. Dealers Only)

* We believe this source and their products to be reliable. There may be additional manufacturers of such products. General Motors does not
endorse, indicate any preference for or assume any responsibility for the products from this firm or for any such items, which may be available from
other sources.

WARRANTY INFORMATION
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 577
Chevrolet Venture V6-3.4L VIN E 2902

WORKSHEET - BRAKE LATHE CALIBRATION

Important

Brake lathe calibration should be performed and recorded monthly or if you are consistently measuring high LRO after rotor refinishing.

Disclaimer

GM Brake Service Procedure


GM BRAKE SERVICE PROCEDURE

1. Remove the wheel and caliper.

2. Measure rotor thickness. In order to determine if the rotor can be refinished, do the following steps:

Important
If performing routine Brake Service for worn pads only, and the rotors are not damaged and measure within specification - DO NOT
REFINISH ROTORS.
1. Remove the rotor(s).

2. Measure the rotor for original thickness using a brake micrometer. Multiple measure points should be taken and the lowest measurement
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 578
Chevrolet Venture V6-3.4L VIN E 2903
should be recorded.

3. Reference the Minimum Thickness specification stamped on the backside of the rotor or SI for Minimum Thickness specification/other.
In most cases, the rotor should be refinished unless the measurement taken makes it obvious that refinishing the rotor would take the
measurement under the Minimum Thickness specification (then replacement is necessary). DO NOT use any other manufacturers rotor
specifications.

3. ***Record the lowest ORIGINAL rotor thickness measurement on the repair order hard copy as noted in the "Repair Order Documentation -
Rotor Refinish" section of this bulletin.

4. Clean all of the mating surfaces between the hub, the rotor and the wheel using the J 42450A - Wheel Hub Cleaning Kit and J 41013 - Whiz
Wheel(R).

If rotors are not to be refinished - Go To Step 8.

Important
Cleaning all mating surfaces and making them free of corrosion, burrs and other debris (which includes removal of Hubless rotors) is
critical and MUST be performed whether using an On-Car or Bench Lathe Refinish Procedure.

5. Be sure to follow the appropriate refinishing procedure listed below for the type of lathe you are using.

Important
Only replace the rotors if they do not meet the Minimum Thickness specification.

Important
DO NOT REFINISH NEW ROTORS.

Important
Only remove the necessary amount of material from each side of the rotor and note that equal amounts of material do not have to be removed
from both sides on any brake system using a floating caliper.

Important
Prior to making the cut, install the recommended clip-on style disc silencer supplied with the lathe. Use of this silencer is critical to prevent
chatter from occurring during the cut.

Bench Type Lathe

1. Refinish the existing rotor on an approved, well-maintained lathe to guarantee smooth, flat and parallel surfaces.

2. Check for clean and true lathe adapters and make sure the arbor shoulder is clean and free of debris or burrs. For more information, see
the "Brake Lathe Calibration Procedure (Bench-Type)" section in this bulletin.

3. On the outboard area of the rotor, position the cutting tools one eighth of an inch into the brake pad area of the rotor. Feed the cutting
tools into the rotor until they cut the rotor to new metal, a full 360 degrees. Zero each dial and back off a full turn

4. Move the cutting bits to the middle of the rotor and do the same procedure. If zero is passed during the process, reset zero. Back off a full
turn.

5. Position the cutting bits one eighth of an inch inside the inboard (closest to the hub) edge of the brake pad contact area. Do the same
procedure. If zero is passed during the process, reset zero.

6. Back off a full turn and position the cutting bits all the way inboard in preparation to refinish the full rotor surface. Advance both tool cutters
to the zero setting plus just enough to clean up the entire rotor surface.

7. After completing the refinish, sand both sides of the rotor for approximately one minute per side using a sanding block and 130-150 grit
sandpaper to obtain a non-directional finish.

On-Car Type Lathe

1. Reinstall the rotor(s).

Important
When using the On-Car lathe on vehicles equipped with limited slip (or posi-trac) rear system, it is critical that the rear drive shaft is
disconnected/disengaged prior to operation of the On-Car lathe. Remember to mark and re-index the drive shaft correctly on re-assembly
to prevent creating driveline vibration. Whenever the lathe drive motor is being switched on, the operator MUST keep their body out of
the wheel well area until the machine has reached its normal operating RPM.

2. Refinish the existing rotor on an approved, well-maintained lathe to guarantee smooth, flat and parallel surfaces.

Important
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 579
Chevrolet Venture V6-3.4L VIN E 2904
When raising the vehicle on the lift, be sure to have it at a good working height (waist high is average) to accommodate mounting the
On-Car lathe. Optimally, the center piston on the lathe trolley will be mid-travel. If the lathe trolley center piston is completely
compressed (bottoming out) or inversely fully extended and hanging off the vehicle hub, this could affect the calibration time of the lathe.

3. Select the correct adapter for the vehicle you're working on and mount it to the hub with the vehicle lug nuts. Hand tighten 34-41 Nm
(25-30 lb ft) the nuts using equal torque. DO NOT use impact wrenches, excessive torque will damage the adapter.

Important
Ensure the adapter sits flush on the rotor hat surface. Be sure to remove any rust, rotor retaining clips, etc. that may preclude the adapter
from sitting flat on the mounting surface.

4. Connect the lathe to the adapter, turn on the lathe and activate the computer to compensate for run-out in the hub.

5. Once the computer indicates the compensation process was successful, on the outboard area of the rotor, position the cutting tools one
eighth of an inch into the brake pad area of the rotor. Feed the cutting tools into the rotor until they cut the rotor to new metal, a full 360
degrees. Zero each dial and back off a full turn.

6. Move the cutting bits to the middle of the rotor and do the same procedure. If zero is passed during the process, reset zero. Back off a full
turn.

7. Position the cutting bits one eighth of an inch inside the inboard (closest to the hub) edge of the brake pad contact area. Do the same
procedure. If zero is passed during the process, reset zero.

8. Back off a full turn and position the cutting bits all the way inboard in preparation to refinish the full rotor surface. Advance both tool
cutters to the zero setting plus just enough to clean up the entire rotor surface.

9. After completing the refinish, sand both sides of the rotor for approximately one minute per side using a sanding block and 130-150 grit
sandpaper to obtain a non-directional finish.

10. Dismount the lathe, but leave the lathe adapter attached to the vehicle.

6. Once the rotor has been properly machined, wash the rotor with soap and water (use a mild dish washing soap) or wipe it clean with GM
approved brake cleaner, P/N 88862650 (Canadian P/N 88901247).

Important
Thoroughly cleaning the rotor will prevent the possible transfer of finite metal dust left as a by-product of machining to the pad material
during the seating process, thus reducing the opportunity for squeaks or other noises to occur.

7. ***Record the REFINISHED rotor thickness measurement on the repair order hard copy. Refer to the "Repair Order Documentation - Rotor
Refinish" section of this bulletin.

8. Setting up to measure for Lateral Run Out (LRO):

Important
Measuring for Lateral Run Out (LRO) (steps 8 - 15) is no longer required however, these steps are being left in the overall procedure as a
good check to be performed in the case of a repeat pulsation complaint. If you are not checking for LRO, go to step 16.

Bench-Type Lathe

1. Ensure that the mating surfaces of the rotor hat section and the hub mating surface are clean and free of debris.

2. Mount the new, original or refinished rotor onto the vehicle hub.

Important
Always hold the rotor on the bottom half so any debris that may be dislodged from the vents will fall out instead of falling into the
mounting area. Any movement or jarring from the rotor falling over on the studs can release rust from the vents on the rotor.

3. Tilt the top of the rotor in towards the vehicle so you can see the studs and ease the rotor onto the studs.

4. Slide the rotor all the way to the hub and hold it in place until you have placed one of the conical washers (with the tapered hole side
facing out) and run the first lug nut up tight by hand so the rotor doesn't move when you release it.

5. Place the conical washers on the rest of the studs (with the tapered hole side facing out), start and snug the lug nuts by hand.

6. Using the one half inch drive impact wrench and a torque stick (J 39544) or equivalent, start with the lug nut opposite of the one you first
tightened by hand and tighten the lug nuts using a star pattern until they touch the hub but do not completely torque. Then again, starting
with the first lug nut you tightened by hand, tighten all the lug nuts in a star pattern to the specific vehicle torque specification.

7. DO NOT reinstall the caliper or the wheel at this time.


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 580
Chevrolet Venture V6-3.4L VIN E 2905

On-Car Type Lathe

1. Leave the On-Car adapter on the wheel.

2. Proceed to Step 9.

9. Fasten the dial indicator to the steering knuckle so that the indicator needle contacts the rotor outboard friction surface approximately 6.35
mm (0.25 in) from the rotor's outer edge. The stylus should be perpendicular to the friction surface of the rotor.

Important
Make sure the dial indicator needle tip is screwed tight, a loose tip could cause false readings.

10. Measure for LRO. Follow the procedure below to determine if the LRO is within specification (0.050 mm (0.002 in) or LESS).

1. Rotate the rotor and locate the point on the rotor where the lowest dial indicator reading is indicated and set the dial indicator to zero.

2. Rotate the rotor from the low point and locate the point with the highest dial indicator reading (rotor "high spot"). Note the amount and
mark the location of the "high spot" on the rotor and mark the closest wheel stud relative to this location. If the high point falls between
two studs, mark both studs. In instances where the vehicle has "capped lug nuts" you should mark the hub.

11. If the Lateral Run Out (LRO) measurement is 0.050 mm (0.002 in) or LESS, no correction is necessary. Go to Step 15 if this is the first rotor
completed. Go to Step 16 if this is the second rotor completed. If the LRO is GREATER than 0.050 mm (0.002 in), go to Step 12.

12. If the LRO measurement is greater than 0.050 mm (0.002 in), use the following procedure to correct for LRO:

Important
If the LRO measurement is over 0.279 mm (0.011 in), determine the source or cause of the LRO and correct it (i.e. verify drive axle nut
torque specification, refinished rotor is source of LRO due to a lathe qualification issue - see "Brake Lathe Calibration Procedure").

Hubless Rotor

1. Remove the rotor and using the Brake Align(R) application chart (found in TSB 01-05-23-001B), choose the correct plate to bring the
rotor LRO to 0.050 mm (0.002 in) or less. The plates come in 0.0762 mm (0.003 in), 0.1524 mm (0.006 in) and 0.2286 (0.009 in)
compensation. For more information on proper plate selection, see the instruction video/DVD included in the "Brake Align(R)" kit or
TSB 01-05-23-001B.

2. Align the V-notch of the selected Brake Align(R) correction plate to the marked wheel stud ("high spot") or between the two points
marked (if the "high spot" is between two wheel studs).

Important
IF Brake Align(R) Correction Plates are not available for the vehicle being serviced, refer to SI Document - Brake Rotor Assembled
Lateral Runout Correction for correcting LRO.

Important
Per Brake Align(R) manufacturer, NEVER attempt to stack two or more Correction Plates together on one hub. NEVER attempt to reuse
a previously installed Correction Plate.

3. Reinstall the rotor using the same method and precautions as the first time - found in Step 8. Make sure to index the rotor correctly to the
marks made in step 10, otherwise LRO will be comprised.

Hubbed / Captured / Trapped Rotor

1. Measure the rotor thickness.

2. Refinish or replace the rotor (see Service Information for further details).

13. Use a Dial Indicator to measure the rotor to verify the LRO is within specification.

14. If using,

BENCH LATHE - DO NOT remove conical washers and lug nuts at this time.

ON-CAR LATHE - You must remove adapter and install conical washers and lug nuts to retain rotor position.

Important
For Hubless rotor design, while removing the adapter, you must hold the rotor tight to the hub and install the top conical washer and lug nut
first to ensure no debris falls between the surface while removing the adapter. Then, install the remaining conical washers and lug nuts.
Otherwise, LRO will be comprised.
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 581
Chevrolet Venture V6-3.4L VIN E 2906

15. Perform Steps 1 through 7 on the opposite side of the vehicle (steps 1-12, if performing LRO).

16. Reinstall the rotors on both sides of the vehicle and perform the following steps:

1. Reinstall the calipers and pads.

2. Pump the brakes to pressurize the calipers.

3. Remove the lug nuts/conical washers.

4. Install and properly torque the wheels.

Important
It is critical to follow the star pattern wheel torque procedure and use the proper tools (torque stick or torque wrench) as referenced in SI.

17. Road test the vehicle to verify the repairs.

Brake Lathe Calibration Procedure


BRAKE LATHE CALIBRATION PROCEDURE

Calibration of the brake lathe should be performed and recorded monthly or whenever post-service brake rotor LRO measurements are consistently
reading above specification.

BENCH-TYPE LATHE

Use the following procedure to calibrate a Bench-type brake lathe:

1. After refinishing a rotor, loosen the arbor nut and while holding the inside bell clamp to keep it from rotating, rotate the rotor 180 degrees.

2. Retighten the arbor nut and set the dial indicator on the rotor using the same instructions as checking the run out on the vehicle.

3. Rotate the arbor and read the runout.

4. Divide the reading by two and this will give you the amount of runout the lathe is cutting into the rotor.

Important
If there is any runout, you will need to machine the inside bell clamp in place on the lathe (this procedure is for a Bench type lathe ONLY,
DO NOT machine inside the bell clamp on an On-Car type lathe).

Machining the Inside Bell Clamp (Bench Type Lathe Only)

Any nicks or burrs on the shoulder of the arbor must be removed. An 80-grit stone can be used to accomplish this. Spray WD-40(R) on the
shoulder and with the lathe running, hold the stone flat against the shoulder surface using slight pressure. When the burrs are gone, clean the
surface. Burrs must also be removed from the hub of the inside bell clamp. This can be accomplished with the stone and WD-40(R). Keep the stone
flat on the hub while removing the burrs. After removing the burrs, clean the hub.

Place the bell clamp on the arbor of the lathe and use the small radius adapters first and then spacers to allow you to tighten the arbor nut to secure
the bell clamp to the lathe. Position the tool bit in the left hand of the rotor truer so you can machine the face of the bell clamp. Machine the face of
the bell clamp taking just enough off of it to cut the full face of the clamp the full 360 degrees. Before you loosen the arbor nut, match mark the hub
of the bell clamp to the arbor and line up these marks before machining a rotor. A magic marker can be used to make the match marks. Machine a
rotor and recheck the calibration. Repeat this procedure on all Inside Bell Clamps used.

Important

If runout is still present, contact the brake lathe supplier.

ON-CAR TYPE LATHE

Use the following procedure to calibrate an On-Car brake lathe:

1. Connect the lathe to a vehicle using the appropriate adapter.

2. Attach a vise-grip dial indicator to a fixed point in the wheel well and bring the dial indicator to a flat surface on the cutting head.

3. Turn on the lathe and press the "start" button so the lathe begins to compensate.

4. Once compensation is complete, note the runout as measured by the dial indicator. Measured runout at this point is overstated given that it is
outside the rotor diameter.
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 582
Chevrolet Venture V6-3.4L VIN E 2907

5. If runout is in excess of 0.1016 mm (0.004 in) (0.050 mm (0.002 in) as measured within the rotor diameter), calibration must be tightened.
Follow manufacturer's instructions for tightening the calibration of the lathe. This information is found in the manual supplied with the lathe.

Important
If the machine is taking a long time to compensate during normal use, prior to checking the lathe calibration, it is recommended that the
machine be disconnected from the adapter and the adapter (still connected to the vehicle) is rotated 180 degrees and the machine reattached.
This will accomplish two things: - It will re-verify the machine is properly attached to the adapter. - It will change the location of the runout
(phase) relative to the machine and thus possibly allow for quick compensation as a result of the position change.

The following information has been added as a reference to ensure your Pro-Cut PFM lathe provides a consistent smooth surface finish over long
term usage.

Cutting Tips / Depth of Cut / Tip Life

The cutting tips must be right side up. Reference marks always face up. The cutting tips may not have chips or dings in the surface of the points.
Cuts of 0.1016-0.381 mm (0.004-0.015 in) will provide the best surface finish and the optimal tip life. When cleaning or rotating the cutting bits,
make sure that the seat area for the tip on the tool is free and clear of debris.

Cutting Head

On each brake job, the technician must center the cutting head for that particular vehicle using one of the mounting bolt holes on the slide plate.
Once the head is centered, it is vital that the technician use one hand to push the head firmly and squarely back into the dovetail on the slide plate
while using the other hand to tighten the Allen-Hex bolt that secures the head. Failure to do this could result in chatter occurring during the cut.

Tool Holder Plate (Cutting Head)

The tool holder plate is the plate that the cutting arms are attached to. It can bend or break if a technician accidently runs the cutting arms into the
hub of the rotor while the rotor is turning. (Cuts of more than 0.508 mm (0.020 in) can also bend this plate). Once bent, the lathe will most likely
not cut properly until the tool holder plate is replaced. In order to verify the condition of the tool holder plate on a machine that will not cut right,
remove the mounting bolt and remove the cutting head from the slide plate. With the cutting head titled at an angle, lay the long edge of the tool
holder plate down on the flat part of the slide plate. If any gap can be seen between the edge and the slide plate, the tool holder plate is bent and the
source of vibration. Also check to ensure that the cutting arms are lying flat on the upper side of the tool holder plate. If the mounting arm post is
bent, it will show itself by having the back of the cutting arm lifting off the surface of the tool holder.

Gib Adjustment / Loose Gib

As wear occurs between the slide plate and the box it rides on, you must take up the slack. You do this by way of a moveable wedge, which we call
the gib. Your lathe manual details adjustment process, which you should perform when required after monthly checks or whenever surface finish is
inconsistent.

Brake Pulsation
BRAKE PULSATION

Brake pulsation is caused by brake rotor thickness variation. Brake rotor thickness variation causes the piston in the brake caliper, when applied, to
"pump" in and out of the caliper housing. The "pumping" effect is transmitted hydraulically to the brake pedal. Brake pulsation concerns may result
from two basic conditions:

1. Thickness Variation Pulsation is Caused by Lateral Run Out (LRO). LRO on a brake corner assembly is virtually undetectable unless
measured (with a dial indicator after the brake service) and will not be detected as brake pulsation during an after brake service test drive. If
the brake corner is assembled with excessive LRO (greater than 0.050 mm (0.002 in), thickness variation will develop on the brake rotor over
time and miles. Excessive LRO will cause the brake pads to wear the brake rotors unevenly, which causes rotor thickness variation. Pulsation
that is the result of excessive Lateral Run Out usually develops in 4,800-16,000 km (3,000-10,000 mi). The more excessive the LRO, the
faster the pulsation will develop. LRO can also be induced when uneven torque is applied to wheel nuts (lug nuts). Improper wheel
tightening after tire rotation, spare tire usage, brake inspection, etc. can be the cause of brake pulsation. Again, it usually takes 4,800-16,000
km (3,000-10,000 mi) AFTER the service event for the condition to develop. The customer does not usually make the connection between
the service event and the awareness of the pulsation. The proper usage of torque wrenches and/or torque sticks (torque limiting sockets) will
greatly reduce or eliminate the pulsation conditions after wheel service events. The improper use of impact wrenches on wheel nuts greatly
increases the likelihood of pulsation after wheel service.

The following are examples of pulsation conditions and reimbursement recommendations:

- If the customer noticed the condition between 4,800-16,000 km (3,000-10,000 mi) and it gradually got worse, normally the repair would
be covered. The customer may tolerate the condition until it becomes very apparent.

- If a GM dealer performed a prior brake service, consider paying for the repair and then strongly reinforce proper brake lathe
maintenance.
- If the customer had the brake service done outside of a GM dealership, normally GM would not offer any assistance.

- If a customer indicated they had wheel service, ask who performed the service. Then;
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 583
Chevrolet Venture V6-3.4L VIN E 2908

- If a GM dealer performed the service, consider paying for the repair and then strongly reinforce the use of torque sticks at the dealer.
Two common size torque sticks cover 90% of all GM products. Each technician needs to use torque sticks properly every time the
wheel nuts are tightened.

- If the customer had the wheel service done outside of a GM dealership, normally GM would not offer any assistance.

2. Thickness Variation Pulsation Caused by Brake Rotor Corrosion - Rotor corrosion is another form of thickness variation, which can cause a
pulsation concern and can be addressed as follows:

- Cosmetic Corrosion:

In most instances rotor corrosion is cosmetic and refinishing the rotor is unnecessary.

- Corrosion - Pulsation Caused by Thickness Variation (Lot Rot / Low Miles - 0-321 km (0-200 mi):

At times more extensive corrosion can cause pulsation due to thickness variation. This usually happens when the vehicle is parked for
long periods of time in humid type conditions and the braking surface area under the pads corrodes at a different rate compared to the rest
of the braking surface area. Cleaning up of braking surfaces (burnishing) can be accomplished by 10 - 15 moderate stops from 56- 64
km/h (35 - 40 mph) with cooling time between stops. If multiple moderate braking stops do not correct this condition, follow the "Brake
Rotor Clean-Up Procedure" below.

- Corrosion - Pulsation Caused by Thickness Variation (without rotor flaking / higher mileage - 3,200-8,000 km (2,000-5,000 mi):

In some cases, more extensive corrosion that is not cleaned up by the brake pad over time and miles can cause the same type of pulsation
complaint due to thickness variation. In these cases, the rotor surface is usually darker instead of shiny and a brake pad foot print can be
seen against the darker surface. This darker surface is usually due to build-up, on the rotor material surface, caused by a combination of
corrosion, pad material and heat. To correct this condition, follow the "Brake Rotor Clean-up Procedure" below.

- Corrosion - Pulsation Caused by Thickness Variation (with rotor flaking / higher mileage - 8,000 + km (5,000 + miles) :

At times, more extensive corrosion over time and miles can cause pulsation due to thickness variation (flaking). This flaking is usually a
build up, mostly on the rotor material surface, caused by a combination of corrosion, pad material and heat. When rotor measurements are
taken, the low areas are usually close to the original rotor thickness (new rotor) measurement and the high areas usually measure more
than the original rotor thickness (new rotor) measurement (depending on mileage and normal wear). To correct this condition, follow the
"Brake Rotor Clean-up Procedure" described below.

Important
In some flaking instances, cleaning-up this type of corrosion may require more rotor material to be removed then desired. Customer
consideration should be taken in these situations and handled on a case by case basis, depending on the amount/percentage of rotor life
remaining and the vehicle's warranty time and miles.

Brake Rotor Clean-Up Procedure


BRAKE ROTOR CLEAN-UP PROCEDURE

Clean-up the rotors on an approved, well-maintained brake lathe to guarantee smooth, flat and parallel surfaces. Check for clean and true lathe
adapters and make sure the arbor shoulder is clean and free of debris or burrs. For more information see the "Brake Lathe Calibration Procedure"
section in this bulletin.

1. On the outboard area of the rotor, position the cutting tools one eighth of an inch into the brake pad area of the rotor. Feed the cutting tools
into the rotor until they cut the rotor to new metal, a full 360 degrees. Zero each dial and back off a full turn.

2. Move the cutting bits to the middle of the rotor and do the same procedure. If zero is passed during the process, reset zero. Back off a full
turn.

3. Position the cutting bits one eighth of an inch inside the inboard (closest to the hub) edge of the brake pad contact area. Do the same
procedure. If zero is passed during the process, reset zero.

4. Back off a full turn and position the cutting bits all the way inboard in preparation to refinish the full rotor surface. Advance both tool cutters
to the zero setting plus just enough to clean up the entire rotor surface.

5. After completing the refinish, sand both sides of the rotor for approximately one minute per side using a sanding block and 130-150 grit
sandpaper to obtain a non-directional finish.

Important
Only remove the necessary amount of material from each side of the rotor and note that equal amounts of material do not have to be removed
from both sides on any brake system using a floating caliper.

Important
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 584
Chevrolet Venture V6-3.4L VIN E 2909
In many of these instances, such a minimal amount of material is removed from the rotor that customer satisfaction is not a concern for future
brake services. This procedure is intended to "Clean-up" the rotor surface and should be conveyed to the customer as such - not as "cut",
"refinish" or "machine", which tends to be terms understood as a substantial reduction of rotor material/life. If the brake lathe equipment
being used is not capable of removing minor amounts of material while holding tolerances, further lathe maintenance, repair, updates or
equipment replacement may be necessary.

Brake Noise
BRAKE NOISE

Some brake noise is normal and differences in loading, type of driving, or driving style can make a difference in brake wear on the same make and
model. Depending on weather conditions, driving patterns and the local environment, brake noise may become more or less apparent. Verify all
metal-to-metal contact areas between pads, pad guides, caliper and knuckles are clean and lubricated with a thin layer of high temperature silicone
grease. Brake noise is caused by a "slip-stick" vibration of brake components. While intermittent brake noise may be normal, performing 3 to 4
aggressive stops may temporarily reduce or eliminate most brake squeal. If the noise persists and is consistently occurring, a brake dampening
compound may be applied to the back of each pad. This allows parts to slide freely and not vibrate when moving relative to each other. Use
Silicone Brake Lubricant, ACDelco P/N 88862181 (Canadian P/N 88862496) or equivalent.

The following noises are characteristics of all braking systems and are unavoidable. They may not indicate improper operation of the brake system.

Squeak/Squeal Noise:

- Occurs with front semi-metallic brake pads at medium speeds when light to medium pressure is applied to the brake pedal.

- Occasionally a noise may occur on rear brakes during the first few stops or with cold brakes and/or high humidity.

Grinding Noise:

- Common to rear brakes and some front disc brakes during initial stops after the vehicle has been parked overnight.

- Caused by corrosion on the metal surfaces during vehicle non-use. Usually disappears after a few stops.

Groan Noise:

A groan type noise may be heard when stopping quickly or moving forward slowly from a complete stop. This is normal. On vehicles equipped
with ABS, a groan or moan type noise during hard braking applications or loose gravel, wet or icy road conditions is a normal function of the ABS
activation.

Key Points - Frequently Asked Questions


KEY POINTS - FREQUENTLY ASKED QUESTIONS

- Q: How do on-car lathes react to Axle Float? Does the play affect the machining of the rotor, either surface finish or LRO?

A: Because the Pro-Cut on-car lathe adjusts in a live mode while spinning the hub/rotor, the dynamics of a floating axle are effectively
eliminated. Once the lathe is compensated, there is no difference in the cutting/surface finish and LRO are just the same as with a
non-floating axle.

- Q: Which lathe is essential for performing brake work, the bench or on-car?

A: Dealers must have a well maintained bench lathe and well maintained on-car lathe. These lathes need to be calibrated on a monthly basis.
BOTH lathes are essential to providing quality brake service.

- Q: What is the expected tip life for an on-car lathe?

A: The geometry and composition of the Pro-Cut tips are designed for "single pass" cutting. When using the Pro-Cut the cutting depth should
be set to take all material needed to get below rust grooves, eliminate all run-out and resurface the entire disc in a single pass. Cuts of
0.1016-0.381 mm (0.004-0.015 in) will provide the best surface finish and the optimal tip life. No "skim cut" or "finish cut" is needed.
Failure to follow this procedure will shorten tip life. The Pro-cut tips will last between 7-12 cuts per corner. With three usable corners, a pair
of tips is good for at least 21 cuts.

- Q: Why does GM recommend the use of single pass (referred to as "positive rake") bench and on-car brake lathes?

A: GM Service and GM Brake Engineering have performed competitive evaluations on a significant number of bench and on-car brake
lathes. These tests measured critical performance characteristics such as flatness, surface finish and the ability of the lathe to repeat accuracy
over many uses. In each test, single pass lathe designs out performed the competitors. Single pass brake lathes are more productive requiring
less time to perform the same procedure.

- Q: Is it okay to leave the caliper/pads installed while cutting rotors using an on-car lathe?

A: On-car lathes should never be used with the pads and calipers installed on the vehicle. The debris from cutting the rotors can contaminate
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 585
Chevrolet Venture V6-3.4L VIN E 2910
the brake pads/calipers which can lead to other brake concerns and comebacks.

- Q: What information needs to be documented on the Repair Order?

A: Any claim that is submitted using the labor operations in this bulletin, must have the Original Rotor Thickness and Refinish Rotor
Thickness (if refinished) documented on the repair order. For more information, refer to the "Repair Order Required Documentation" section
of this bulletin.

All Warranty Repair Orders paid by GM, are subject to review for compliance and may be debited where the repair does not comply with this
procedure.

Brake Warranty
BRAKE WARRANTY

Brake Rotors:

- Brake rotor warranty is covered under the terms of the GM New Vehicle Limited Warranty. Reference the vehicle's warranty guide for
verification.

- Rotors should not be refinished or replaced during normal/routine pad replacement.

- Rotors should not be refinished or replaced and is ineffective in correcting brake squeal type noises and/or premature lining wear out.

- Rotors should not be refinished or replaced for cosmetic corrosion. Clean up of braking surfaces can be accomplished by 10-15 moderate
stops from 56-64 km/h (35-40 mph) with cooling time between stops.

- Rotors should not be refinished or replaced for rotor discoloration/hard spots.

- Rotors should be refinished NOT replaced for Customer Pulsation concerns. This condition is a result of rotor thickness variation, usually
caused by LRO (wear induced over time and miles) or corrosion (Lot Rot).

- When rotor refinishing, only remove the necessary amount of material from each side of the rotor and note that equal amounts of material do
not have to be removed from both sides on any brake system using a floating caliper.

- Rotors should be refinished for severe scoring - depth in excess of 1.5 mm (0.060 in).

Important
If the scoring depth is more than 1.5 mm (0.060 in) after the rotor is refinished, it should be replaced.

- It is not necessary to replace rotors in pairs. Rotors may be replaced individually. However, caution should be exercised, as a variance in
surface finish may cause a brake pull condition.

- New rotors should not be refinished before installation. Original equipment rotor surfaces are ground to ensure smooth finish and parallelism
between mounting and friction surfaces. If a new rotor has more than 0.050 mm (0.002 in) Lateral Run Out (LRO) when properly mounted
on the hub, correct it using one of the following methods:

1. For hubless rotor designs, use the correction plate procedure found in the "GM Brake Service Procedure for Hubless Rotors" outlined in
this bulletin.

2. For hubbed/trapped/captured rotor designs, refinish the rotor using an On-Car lathe and the procedure outlined in this bulletin.

- Never reuse rotors that measure under the Minimum Thickness specification. In this instance, the rotor should be replaced.

Important
If the Minimum Thickness specification is not visible on the rotor, reference Service Information (SI) for the specific vehicle application. DO
NOT use any other manufacturers rotor specifications.

Brake Pads:

Important
When determining the warranty coverage (as an example) - if all four front or four rear brake pads are excessively worn evenly, that would
NOT be covered under warranty since this type of wear is most likely due to driving habits or trailering. However, if the brake pads are
excessively worn un-evenly, side-to-side or same side/inner-to-outer pads, then consideration should be given to cover this under warranty
since this type of wear is most likely due to poor operation of other braking components.

- Consideration should be given for covering brake pads up to 39,000 km (24,000 mi) (excluding owner abuse, excessive trailering, or the
situations that would not be considered normal use).

- Installation of new rotors does not require pad replacement. Do not replace pads unless their condition requires it - excessively worn, damage
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 586
Chevrolet Venture V6-3.4L VIN E 2911
or contaminated.

Brake Wear:

Several factors impact brake lining wear and should be taken into account when reviewing related issues:

- heavy loads / high temperatures / towing / mountainous driving / city driving / aggressive driving / driver braking characteristics (left foot or two
feet)

The following are conditions that may extend brake lining wear:

- light loads / highway driving / conservative driving / level terrain

Technical Service Bulletin # 99-01-39-004C Date: 090612

A/C - Musty Odors Emitted From (HVAC) System


TECHNICAL

Bulletin No.: 99-01-39-004C

Date: June 12, 2009

Subject: Air Conditioning Odor (Install Evaporator Core Dryer Kit and Apply Cooling Coil Coating)

Models:

1993-2010 GM Passenger Cars and Trucks (Including Saturn)


2010 and Prior HUMMER H2, H3
All Equipped with Air Conditioning

Supercede:
This bulletin is being revised to add the 2009 and 2010 model years. Please discard Corporate Bulletin Number 99-01-39-004B (Section 01 -
HVAC).

Condition

Some customers may comment about musty odors emitted from the Heating, Ventilation and Air Conditioning (HVAC) system at vehicle start-up
in hot, humid conditions.

Cause

This condition may be caused by condensate build-up on the evaporator core, which does not evaporate by itself in high humidity conditions. The
odor may be the result of microbial growth on the evaporator core. When the blower motor fan is turned on, the microbial growth may release an
unpleasant musty odor into the passenger compartment.

There are several other possible sources of a musty odor in a vehicle. A common source is a water leak into the interior of the vehicle or foreign
material in the HVAC air distribution system. Follow the procedures in SI for identifying and correcting water leaks and air inlet inspection.

The procedure contained in this bulletin is only applicable if the odor source has been determined to be microbial growth on the evaporator core
inside the HVAC module.

Correction

Many vehicles currently incorporate an afterblow function within the HVAC control module software. The afterblow feature, when enabled,
employs the HVAC blower fan to dry the evaporator after vehicle shut down and this function will inhibit microbial growth. Technicians are to
confirm that the customer concern is evaporator core odor and that the vehicle has the imbedded afterblow feature, as defined in the SI document
for that specific vehicle model, model year and specific HVAC option. Refer to SI for enabling the afterblow function. Vehicles being delivered in
areas prone to high humidity conditions may benefit from having the afterblow enabled calibration installed prior to any customer comment.

Important
If the vehicle is not factory equipped with the imbedded afterblow enable feature, it may be added with the Electronic Evaporator Dryer
Module Kit (P/N 12497910 or AC Delco 15-5876).

Important
When installing the Electronic Evaporator Dryer Module, you MUST use the included electrical splice connectors to ensure a proper splice.
Complete detailed installation instructions and self testing procedures are supplied with the kit. If necessary, the Electronic Evaporator Dryer
Module may be installed underhood if it is protected from extreme heat and water splash areas.

To immediately remove the evaporator core odor on all suspect vehicles, it is necessary to eliminate the microbial growth and prevent its
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 587
Chevrolet Venture V6-3.4L VIN E 2912
re-occurrence. To accomplish this, perform the following procedure:

Vehicle and Applicator Tool Preparation


1. The evaporator core must be dry. This may be accomplished by disabling the compressor and running the blower fan on the recirc heat
setting for an extended period of time.

Note
Compressor engagement will cause the evaporator core to remain wet and will prevent full adherence of the Coiling Coil Coating to the
evaporator core surfaces.

2. Verify that the air conditioning drain hose is not clogged and place a drain pan beneath the vehicle.
3. Place a protective cover over the carpet below the evaporator core.
4. Remove the cabin air filter, if equipped, and cover the opening prior to applying the Cooling Coil Coating, as the product may clog the filter.
If the cabin air filter appears to have little or no remaining life, suggest a replacement to your customer.
5. If the HVAC module has a blower motor cooling tube, be careful NOT TO SPRAY THE COOLING COIL COATING INTO THE
BLOWER MOTOR COOLING TUBE.
6. Attach the Flexible Applicator Pressure Spray Tool (J-43810-20A) to a compressed air line operating at 586 kPa (85 psi) to 793 kPa (115
psi).
7. Shake the bottle of Cooling Coil Coating well. Screw the bottle onto the cap on the applicator tool's pick-up tube.

Note
The pick-up tube is designed for 120 ml (4 oz) and 240 ml (8 oz) bottles and should coil slightly in the bottom of a 120 ml (4 oz) bottle.

8. Use one of the following three methods to apply the Cooling Coil Coating.

Important
If the Pressure Applicator Spray Tool (J-43810-20A) is not available, the Cooling Coil Coating is also available in an aerosol can (P/N
12377951 (in Canada, 10953503)).

Application Through Blower Motor Control Module Opening


- Remove the blower motor control module (blower motor resistor). Refer to the applicable procedure in SI.
- Clean any debris or foreign material from inside the HVAC module and on the evaporator core surface.
- Apply the Cooling Coil Coating directly to the evaporator core through the blower motor blower motor control module (blower motor
resistor) opening.
- Use the flexible wand to direct the Cooling Coil Coating over the entire evaporator core and surrounding gasket surfaces.
- When the application is complete, install the blower motor blower motor control module (blower motor control module).

Application Through Blower Motor Opening


- Remove the blower motor. Refer to the applicable blower motor removal procedure in SI.
- Clean any debris or foreign material from inside the HVAC module and on the evaporator core surface.
- Apply the Cooling Coil Coating directly to the evaporator core through the blower motor opening.
- Use the flexible wand to direct the Cooling Coil Coating over the entire evaporator core and surrounding gasket surfaces.
- When the application is complete, install the blower motor.

Application Through a Hole in the HVAC Module


- If neither of the two previous application methods are available, it may be necessary to drill a hole in the HVAC module.
- Locate an area of the HVAC module between the blower motor and the evaporator core. Drill a 10 mm (3/8 in) hole in the HVAC
module. Use caution to keep the drill clear of the evaporator core and the blower motor fan.
- With the air distribution vents closed and the blower motor fan speed on HIGH, insert the applicator tool into the hole and spray the
Cooling Coil Coating into the airstream toward the evaporator core.
- Use a GM approved RTV sealant to plug the hole in the HVAC module.

9. After the Cooling Coil Coating application is complete, start and run the vehicle for approximately 10 minutes, with the compressor disabled,
HVAC mode set to Recirculate/Max, heat set to full warm, blower motor fan speed on high, and one window open approximately 12 mm (1/2
in). This cures the Cooling Coil Coating onto the evaporator core surface.
10. While the engine is running, rinse the applicator tool with warm water to prolong the life of the tool. Be sure to spray warm water through the
nozzle to rinse out any residual Cooling Coil Coating still in the capillary pick up tube, otherwise it will dry and clog the applicator tool. Also
remove the small green valve from the bottle cap and rinse it thoroughly while rolling it between two fingers and then reinstall it. If this valve
is clogged , the Cooling Coil Coating will not flow through the applicator tool.
11. Shut off the engine and enable the compressor again.
12. Verify proper HVAC system operation.
13. Remove the protective cover from inside the vehicle.
14. Remove the drain pan from underneath the vehicle.
15. Reinstall the cabin air filter if necessary.
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 588
Chevrolet Venture V6-3.4L VIN E 2913

Parts Information

Important
The Cooling Coil Coating listed below is the only GM approved product for use under warranty as an evaporator core disinfectant and for
the long term control of evaporator core microbial growth.

Warranty Information

For vehicles repaired under warranty, use the table above.

Disclaimer

Technical Service Bulletin # 01-08-42-001G Date: 090504

Lighting - Exterior Lamp Condensation Guidelines


INFORMATION

Bulletin No.: 01-08-42-001G

Date: May 04, 2009

Subject: Exterior Lamp Condensation and Replacement Guidelines

Models:

1993-2010 GM Passenger Cars and Trucks (including Saturn)


2003-2010 HUMMER H2
2006-2010 HUMMER H3
2005-2009 Saab 9-7X

..........................................................................................................................................................................................................................................
Supercede:
This bulletin is being revised to add the 2010 model year. Please discard Corporate Bulletin Number 01-08-42-001F (Section 08 - Body &
Accessories).

..........................................................................................................................................................................................................................................

The following information is being provided to better define the causes of condensation in exterior lamps and includes guidelines for determining
the difference between a lamp with a normal atmospheric condition (condensation) and a lamp with a water leak.

Some exterior lamps, such as cornering, turn signal, backup, headlamps or tail lamps may exhibit very small droplets of water, a fine mist or white
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 589
Chevrolet Venture V6-3.4L VIN E 2914
fog (condensation) on the inside of the lamp lens. This may be more noticeable on lamps with "multi-lens" designs and may be normal during
certain weather conditions.

Condensation occurs when the air inside the lamp assembly, through atmospheric changes, reaches the "dew point". When this takes place, the
moisture in the air within the lamp assembly condenses, creating a fine mist or white fog on the inside surface of the lamp lens.

Most exterior lamps on General Motors vehicles use a vented design and feature a replaceable bulb assembly. They are designed to remove any
accumulated moisture vapor by expelling it through a vent system. The vent system operates at all times, however, it is most effective when the
lamps are ON or when the vehicle is in motion. Depending on the size, shape and location of the lamp on the vehicle, and the atmospheric
conditions occurring, the amount of time required to clear the lamp may vary from 2 to 6 hours.

Completely sealed headlamp assemblies (sealed beams) are still used on a limited number of models being manufactured today. These lamps
require the replacement of the complete lamp assembly if a bulb filament burns out.

Condensation
2006 TrailBlazer Shown

A Fine Mist or White Fog on the Inside Surface of the Lamp Lens Occurring After a Period of High Humidity
- May be located primarily in the lens corners (near the vents) and SHOULD NOT cover more than half the lens surface.
- The condition should clear of moisture when the vehicle is parked in a dry environment, or when the vehicle is driven with the lights ON.
- A comparison of the equivalent lamp on the opposing side of the vehicle indicates a SIMILAR performance.

If the above conditions are noted, the customer should be advised that replacement of a lamp assembly may not correct this condition.

Water Leak
New Style Pickup Shown

Numerous & Various Size Drops of Water Collecting on the Inside Surface of the Lamp Lens After the Vehicle Has Been Exposed to Rain
or a Car Washing Environment
- A condition that covers more than half the surface of the lamp lens.
- An accumulation of water in the bottom of the lamp assembly.
- A condition that WON'T clear when the vehicle is parked in a dry environment, or when the vehicle is driven with the lights ON.
- A comparison of the equivalent lamp on the opposing side of the vehicle indicates a different performance.

Any of the above conditions would indicate the need to service the lens or lamp assembly.

Disclaimer

Technical Service Bulletin # 06-08-44-015B Date: 090512


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 590
Chevrolet Venture V6-3.4L VIN E 2915

Audio System - Noise When Using Portable Playback Unit


INFORMATION

Bulletin No.: 06-08-44-015B

Date: May 12, 2009

Subject: Information on Eliminating Noise in Audio System When Using Portable Playback Device

Models:

2010 and Prior GM Passenger Cars and Trucks (Including Saturn)


2010 and Prior HUMMER H2, H3
2005-2009 Saab 9-7X

..........................................................................................................................................................................................................................................
Supercede:
This bulletin is being revised to add model years. Please discard Corporate Bulletin Number 06-08-44-015A (Section 08 - Body and
Accessories).

..........................................................................................................................................................................................................................................

Some portable audio equipment may be susceptible to certain types of electronic noise present in the vehicle's 12V power outlet.

Here are two ways to eliminate this type of interference:

- If the audio device is capable of being self-powered (battery), use it that way instead of plugging it into the vehicle's power outlet.
- Have the customer purchase a Ground Loop Isolator, such as *Radio Shack Catalog #270-054. This device plugs in between the radio and
the customer's audio device. It is packed with one included Y-Adapter. If purchasing the *Radio Shack product, you will require an
additional Y-Adapter (Catalog #274-369). This device should be installed between the audio player and the AUX input of the vehicle radio.
These catalog numbers are stocked nationally at *Radio Shack Retail Stores in the U.S. and are currently available. Other similar products are
available through other electronics or car stereo retailers defined as Ground Loop Isolators.

Parts Information

Parts are currently available nationally in the U.S. through *Radio Shack retail locations or through the mail at Radio Shack direct ordering
1-800-843-7422. In Canada, parts are available nationally through *The Source By Circuit City retail locations or at www.thesourcecc.com.

*We believe these sources and their products to be reliable. There may be additional manufacturers of such products/materials. General Motors
does not endorse, indicate any preference for or assume any responsibility for the products or material from these firms or for any such items that
may be available from other sources.

Disclaimer
Technical Service Bulletin # 05-08-51-008C Date: 090622

Body - Bumps or Rust Colored Spots in Paint


TECHNICAL

Bulletin No.: 05-08-51-008C

Date: June 22, 2009

Subject: Bumps or Rust Colored Spots in Paint Due to Rail or Iron Dust (Remove Rail Dust)
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 591
Chevrolet Venture V6-3.4L VIN E 2916

Models:

1994-2010 GM Passenger Cars and Trucks (Including Saturn)


2003-2010 HUMMER H2
2006-2010 HUMMER H3
2005-2009 Saab 9-7X

Supercede:
This bulletin is being revised to add model years. Please discard Corporate Bulletin Number 05-08-51-008B (Section 08 - Body and Accessories).

Condition

Visible rust colored spots or bumps on a vehicle's paint surface from rail or iron dust.

Cause

Rail dust comes from tiny iron particles produced from the friction between train wheels and the tracks and gets deposited on the vehicle surfaces.
Iron dust can get deposited on the surface if the vehicle is stored near any operation producing iron dust such as an iron ore yard. Either material
can lay on top of, or become embedded in, the paint surface.

Correction

Because the severity of the condition varies, proper diagnosis of the damage is critical to the success of repairs. Diagnosis should be performed on
horizontal surfaces (hood, roof, deck lid, pick up box, etc.) after the vehicle has been properly cleaned. There are two types of repair materials
recommended to repair rail dust or iron dust:

1. GEL TYPE OXALIC ACID:


- Has the characteristics of the liquid type oxalic acid but stays where you put it because of its gel consistency.
2. CLAY TYPE NON-ACID BASED:
- Requires surface lubricant during use.
- Has different grades available.

Caution

Rail dust remover (Oxalic Acid) is an acidic substance containing chemicals that will break down the iron particles embedded in the finish. When
working with rail dust remover, use the necessary safety equipment, including gloves and goggles. Follow the chemical manufacturer's directions
closely because it may require special handling and disposal.

If, upon inspection, some particles are still present, the various chemical manufacturer's processes can be repeated.

After the removal process, small pits may remain in the clearcoat and can be corrected, in most cases, with a finesse/polish operation.

Procedure

1. Move the vehicle to a cool shaded area and make sure that the vehicle surfaces are cool during the removal process. DO NOT PERFORM
THE REMOVAL PROCESS IN DIRECT SUNLIGHT OR ON A VEHICLE WITH HOT OR WARM BODY PANELS.
2. Wash the vehicle with soap and water. Dry it immediately and clean the affected areas with a wax and grease remover.
3. Perform the removal process according to the chemical manufacturer's directions.

Once the damage has been repaired, the final step involves a polishing process.

Rail Dust Remover Manufacturers

Use the chemical manufacturers listed below, or equivalent:

Auto Magic(R) or Clay Magic(R) products available from:

Auto Wax Company, Inc.


1275 Round Table Dr.
Dallas, TX 75247
(800) 826-0828 (Toll-Free) or (214) 631-4000 (Local)
Fax (214) 634-1342
www.automagic.com
info@autowaxcompany.com
E038 Fallout Gel or E038E Liquid Fallout Remover II available from:

Valvoline Car Brite Company


1910 South State Avenue
Indianapolis, In 46203
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 592
Chevrolet Venture V6-3.4L VIN E 2917
(800) 347-2439 (Toll Free) or (317) 788-9925 (Local)
Fax (317) 788-9930
www.carbrite.com
info@carbrite.com
*We believe these sources and their products to be reliable. There may be additional manufacturers of such products. General Motors does not
endorse, indicate any preference for or assume any responsibility for the products from these firms or for any such items which may be available
from other sources.

If rail dust remover is not available in your area, call one of the numbers listed above for a distributor near your location.

Warranty Information (excluding Saab U.S. Models)

Important
Refer to the Policy & Procedures Manual, section 1.2.1.7 for detailed information regarding warranty coverage for this condition.

Important
In certain cases where the vehicle finish is severely damaged and the actual repair time exceeds the published time, the additional time
should be submitted in the "Other Labor Hours" field.

Warranty Information (Saab U.S. Models)

Disclaimer

Technical Service Bulletin # 07-06-01-016B Date: 090727

Engine - Noise/Damage Oil Filter Application Importance


INFORMATION

Bulletin No.: 07-06-01-016B

Date: July 27, 2009

Subject: Information on Internal Engine Noise or Damage After Oil Filter Replacement

Models:

2010 and Prior Passenger Cars and Trucks (Including Saturn)


2010 and Prior HUMMER H2, H3
2009 and Prior Saab 9-7X

Supercede:
This bulletin is being updated to add model years. Please discard Corporate Bulletin Number 07-06-01-016A (Section 06 - Engine/Propulsion
System).

Important
Engine damage that is the result of an incorrect or improperly installed engine oil filter is not a warrantable claim. The best way to avoid
oil filter quality concerns is to purchase ACDelco(R) oil filters directly from GMSPO.
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 593
Chevrolet Venture V6-3.4L VIN E 2918

Oil filter misapplication may cause abnormal engine noise or internal damage. Always utilize the most recent parts information to ensure the correct
part number filter is installed when replacing oil filters. Do not rely on physical dimensions alone. Counterfeit copies of name brand parts have
been discovered in some aftermarket parts systems. Always ensure the parts you install are from a trusted source. Improper oil filter installation
may result in catastrophic engine damage.

Refer to the appropriate Service Information (SI) installation instructions when replacing any oil filter and pay particular attention to procedures for
proper cartridge filter element alignment. If the diagnostics in SI (Engine Mechanical) lead to the oil filter as the cause of the internal engine noise
or damage, dealers should submit a field product report. Refer to Corporate Bulletin Number 02-00-89-002I (Information for Dealers on How to
Submit a Field Product Report).

Disclaimer

Technical Service Bulletin # 08-06-01-008A Date: 090727

Engine - Drive Belt Misalignment Diagnostics


INFORMATION

Bulletin No.: 08-06-01-008A

Date: July 27, 2009

Subject: Diagnosing Accessory Drive Belt / Serpentine Belt Noise and Availability and Use of Kent-Moore EN-49228 Laser Alignment Tool -
Drive Belt

Models:

2010 and Prior GM Passenger Cars and Trucks (Including Saturn)


2010 and Prior HUMMER H2, H3 Vehicles
2009 and Prior Saab 9-7X

Supercede:
This bulletin is being revised to add a model year and update the Tool Information. Please discard Corporate Bulletin Number 08-06-01-008
(Section 06 - Engine).

Background

Several aftermarket companies offer laser alignment tools for accessory drive systems that can be very helpful in eliminating drive belt noise as a
result of misaligned pulleys. Typically pricing ranges from $160 - $200.

EN-49228 Laser Alignment Tool - Drive Belt

The GM Tool program has now made available a competitive, simple to use and time-saving laser tool to assist in achieving precise alignment of
the drive belt pulleys. This optional tool removes the guesswork from proper pulley alignment and may serve to reduce comebacks from:

- Drive Belt Noise


- Accelerated Drive Belt Wear
- Drive Belt Slippage

Instructions

The instructions below are specific only to the truck Gen IV V-8 family of engines. These instructions are only for illustrative purposes to show
how the tool may be used. Universal instructions are included in the box with the Laser Alignment Tool - Drive Belt.

Caution

- Do not look directly into the beam projected from the laser.
- Use caution when shining the laser on highly polished or reflective surfaces. Laser safety glasses help reduce laser beam glare in many
circumstances.
- Always use laser safety glasses when using the laser. Laser safety glasses are not designed to protect eyes from direct laser exposure.
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 594
Chevrolet Venture V6-3.4L VIN E 2919

1. Observe and mark the serpentine belt orientation.


2. Remove the serpentine belt from the accessory drive system.

3. Install the tool onto the power steering pulley. Position the legs of the tool into the outer grooves of the pulley, farthest from the front of the
engine.
4. Install the retaining cord around the pulley and to the legs of the tool.

5. Put on the laser safety glasses provided with the tool.


6. Depress the switch on the rear of the tool to activate the light beam.
7. Rotate the power steering pulley as required to project the light beam onto the crankshaft balancer pulley grooves.
8. Inspect for proper power steering pulley alignment.

- If the laser beam projects onto the second rib or raised area (1), the pulleys are aligned properly.
- If the laser beam projects more than one-quarter rib 0.9 mm (0.035 in) mis-alignment, adjust the position of the power steering pulley as
required.
- Refer to SI for Power Steering Pulley Removal and Installation procedures.

9. Install the serpentine belt to the accessory drive system in the original orientation.
10. Operate the vehicle and verify that the belt noise concern is no longer present.
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 595
Chevrolet Venture V6-3.4L VIN E 2920

Tool Information

Please visit the GM service tool website for pricing information or to place your order for this tool.

Disclaimer

Technical Service Bulletin # 05-03-08-002C Date: 091016

Suspension - Shock Absorber/Strut Leakage Information


INFORMATION

Bulletin No.: 05-03-08-002C

Date: October 16, 2009

Subject: Information on Replacement of Shock Absorbers and Struts Due to Fluid Leaks

Models:

2010 and Prior GM Passenger Cars and Trucks (Including Saturn)


2010 and Prior HUMMER H2, H3
2009 and Prior Saab 9-7X

Supercede:
This bulletin is being revised to add the 2010 model year and Inspection Procedures. Please discard Corporate Bulletin Number 05-03-08-002B
(Section 03 - Suspension).

This bulletin is intended to help identify the severity of shock absorber and strut fluid seepage. Improper diagnosis may lead to components being
replaced that are within the manufacturer's specification. Shock absorbers and strut assemblies are fluid-filled components and will normally exhibit
some seepage. Seepage is defined as oil film or dust accumulation on the exterior of the shock housing. Shock absorbers and struts are not to be
replaced under warranty for seepage. Use the following information to determine if the condition is normal acceptable seepage or a defective
component.

Important
Electronically controlled shock absorbers (MR) may have a tendency to attract dust to this oil film. Often this film and dust can be wiped
off and will not return until similar mileage is accumulated again.

Inspection Procedure

Note

The shock absorber or strut assembly DOES NOT have to be removed from the vehicle to perform the following inspection procedure.

Use the following descriptions and graphics to determine the serviceability of the component.

Shock Absorbers
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 596
Chevrolet Venture V6-3.4L VIN E 2921

Do Not Replace shock absorbers displaying condition 1 or 2 levels of seepage.

1. Oil or fluid residue only on the bottom or top of the shock absorber and not originating from the shaft seal (the upper part of the lower shock
tube).
2. Light film/residue on approximately 1/3 (a) or less of the lower shock tube (A) and originating from the shaft seal.
Replace shock absorbers displaying conditions 3 and 4 levels of leaks.
3. Oil drip or trail down the lower shock tube and originating from the shaft seal.
4. An extreme wet film of oil covering more than 1/3 (b) of the lower shock tube and originating from the shaft seal.

Coil-over Shock Absorber

Do Not Replace coil-over shock absorbers displaying condition 1 or 2 levels of seepage.

1. Oil or fluid residue only on the bottom of the lower shock absorber tube or the coil-over shock absorber components and not originating from
the shaft seal (located at the top of the coil-over shock tube).
2. Light film/residue on the shock absorber tube, but not on the spring seat and originating from the shaft seal.
Replace coil-over shock absorbers displaying conditions 3 and 4 levels of leaks.
3. Oil drip or trail down the lower shock tube and originating from the shaft seal.
4. An extreme, wet film of oil covering the shock absorber tube and pooling in the spring seat and originating from the shaft seal.

Struts

Do Not Replace Struts displaying condition 1 or 2 levels of seepage.

1. Oil or fluid residue only on the bottom of the strut tube or on other strut components and not originating from the shaft seal.
2. Light film/residue on the strut tube, but not on the spring seat and originating from the shaft seal.
Replace Struts displaying conditions 3 and 4 levels of leaks.
3. Oil drip or trail down the strut tube and originating from the shaft seal (located at the top of the strut tube).
4. Extreme wet film of oil covering the strut tube and pooling in the spring seat and originating from the shaft seal.

Correction

Use the information published in SI for diagnosis and repair.

Use the applicable published labor operation.


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 597
Chevrolet Venture V6-3.4L VIN E 2922

Disclaimer

Technical Service Bulletin # 99-08-64-016C Date: 090729

Body - Maintaining Exterior Weatherstrip Appearance


INFORMATION

Bulletin No.: 99-08-64-016C

Date: July 29, 2009

Subject: Information on Maintaining Exterior Weatherstrip Appearance

Models:

2010 and Prior Passenger Cars and Trucks (including Saturn)


2010 and Prior HUMMER H2, H3
2009 and Prior Saab 9-7X

Supercede:
This bulletin is being revised to add model years and update the parts and procedure information. Please discard Corporate Bulletin Number
99-08-64-016B (Section 08 - Body and Accessories).

Exterior weatherstrips are exposed to a variety of environmental elements, including UV rays, acid rain, insect and bird residue and atmospheric
fallout. All of these may effect the appearance of the weatherstrips; however, they do not effect the functionality of the weatherstrip.

Weatherstrips that are discolored should not be replaced under the normal GM New Vehicle Warranty.

Weatherstrip Maintenance Instructions

Silicone grease on weatherstrips will make them last longer, seal better, and not stick or squeak. Clean the weatherstrips with a mild soap and water
solution. Apply silicone grease with a clean cloth. During very cold, damp weather, frequent application may be required. Refer to the information
below for the recommended maintenance products. Weatherstrips that are not maintained may crack and weather due to environmental elements.

Parts Information

Weatherstrip Conditioning Weatherstrip Lubricant (GM P/N 3634770 [in Canada, P/N 10953518]) or Dielectric Silicone Grease (GM P/N
12345579 [in Canada, P/N 992887]).

Disclaimer
Technical Service Bulletin # 02-07-30-052F Date: 090909

A/T - Fluid Oil Cooler Flush


INFORMATION

Bulletin No.: 02-07-30-052F

Date: September 09, 2009

Subject: Automatic Transmission Oil Cooler Flush and Flow Test Essential Tool J 45096 TransFlow(R)

Models:

2010 and Prior Passenger Cars and Light Duty Trucks (Excluding Saturn)
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 598
Chevrolet Venture V6-3.4L VIN E 2923
2003-2010 HUMMER H2
2006-2010 HUMMER H3
2010 and Prior Saturn Vehicles (Canada Only)
with Automatic Transmission/Transaxle including Allison(R) Transmissions

Supercede:
This bulletin is being revised to update the model years. Please discard Corporate Bulletin Number 02-07-30-052E (Section 07 -
Transmission/Transaxle).

Important
All labor operations that include removal of the transmission from the vehicle include labor time to flush the transmission oil cooler
system.

The J 45096 transmission oil cooling system flush and flow test tool replaces current tool J 35944-A. J 45096 is a self-contained unit utilizing a
12-volt flow meter, shop air supply and DEXRON(R) VI automatic transmission fluid (ATF). In the flush mode, transmission fluid is cycled
through the transmission oil cooling system. High-pressure air is automatically injected into the fluid stream adding agitation to the ATF oil to
enhance the removal of contaminated ATF oil and debris. In the flow mode, an electronic flow meter is used to measure the flow capability of the
ATF oil cooling system. A digital display indicates the ATF oil flow rate in gallons per minute (GPM) along with the amount of ATF oil in the
supply vessel, supply vessel ATF oil temperature, machine cycles and the operating mode. The supply oil vessel has 30 L (32 qt) capacity and the
waste oil vessel has 32 L (34 qt) capacity. The waste oil vessel is constructed of a translucent composite material that allows the user to easily
identify the oil level. The waste oil vessel can accommodate vacuum evacuation and gravity draining. In the code mode, a random, encrypted code
is generated that can be used for verification of flow test results.

Current essential cooler line adapters are used to connect the J 45096 to the automatic transmission oil cooler lines that allows J 45096 to adapt to
General Motors passenger cars and light duty trucks, current and past models (except the Pontiac Vibe, Wave and Chevrolet Aveo).

The tool may be adapted for use on the Pontiac Vibe, Wave and Chevrolet Aveo by dealership personnel with a barbed hose connector and rubber
hose obtained locally. The Vibe's/Wave's/Aveo's transmission has a transmission oil requirement which is slightly different than DEXRON(R) VI
ATF. However, flushing the cooler with DEXRON(R) VI automatic transmission fluid is an acceptable service procedure. Very little fluid remains
in the cooler after the flush procedure and the residual DEXRON(R) VI ATF in the cooler is compatible with the Vibe's/Wave's/Aveo's
transmission fluid.

Notice

Insufficient oil flow through the ATF oil cooling system will cause premature transmission failure. The required minimum ATF oil flow rate
reading is directly related to the supply oil temperature. Refer to the flow rate reference chart for the oil flow rate specification based on the
temperature of the ATF in the supply vessel.

Helpful Hints for Maintaining the Temperature at or above 18°C (65°F)

Important

- The temperature of the supply vessel oil must be 18°C (65°F) or greater for J 45096 to operate. It is recommended to store the J
45096 in an area of the dealership where the room temperature remains at or above 18°C (65°F) when not in use.
- Do not attempt to increase the fluid temperature in the Transflow(R) machine with an engine oil dipstick, or any other immersion
type heater. The Transflow(R) machine has a check valve in the supply reservoir. Inserting a heater will damage the check valve and
the subsequent repair expense would be the dealer's responsibility.
- A heater blanket is available for the Tranflow(R) transmission cooling system flushing tool P/N J 45096. This heater fastens around
the Transflow(R) internal supply vessel and runs on 110 volts AC. The heater will warm the ATF in the supply vessel to at least 18°C
(65°F) and has a thermostat to hold a constant temperature.

Store the Transmission Cooling System Service Tool, J 45096, Transflow(R) machine in a room where the temperature is maintained at or above 18
°C (65°F).

Keep the ATF level in the reservoir low when the Transmission Cooling System Service Tool, J 45096, Transflow(R), is not in use. Store several
gallons of oil in an area where the temperature is maintained at or above 18°C (65°F). Fill the reservoir of the J 45096 as needed before using the
machine on each repair.

With the ATF in a tightly sealed container, place the container in a tub of hot water for a period of time. Then pour the ATF into the reservoir. This
method works best with a low fluid level in the reservoir.

Place the Transflow(R) machine in the direct sunlight with the cabinet door open to expose the reservoir to the rays of the warm sun.
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 599
Chevrolet Venture V6-3.4L VIN E 2924

Flush / Flow Test Procedure

Important
All labor operations that include removal of the transmission from the vehicle include labor time to flush the transmission oil cooler
system.

Refer to SI for Automatic Transmission Oil Cooler Flushing and Flow Test J 45096 for the appropriate procedure.

Important
The J 45096 can be used to flush the transmission oil cooler system on an Allison equipped vehicle, but the flow meter should not be
utilized. Refer to SI for Automatic Transmission Oil Cooler Flushing and Flow Test J 45096 for the appropriate flow check procedure.

Machine Displays

After completion of the flush and flow test, the following information is to be recorded on the repair order. This information is displayed on the
Transmission Cooling System Service Tool, J 45096, Transflow(R) machine when the dial is in the code position.

- Tested flow rate (displayed in Gallons Per Minute (GPM)


- Temperature (displayed is degrees Fahrenheit)
- Cycle number (a number)
- Seven digit Alpha/Numeric flow code (i.e. A10DFB2)

Warranty Information

Important
All labor operations that include removal of the transmission from the vehicle include labor time to flush the transmission oil cooler
system.

Performing a transmission oil cooling system flush and flow test will use between 4.7-7.5 L (5-8 qts) of DEXRON(R)VI transmission fluid. The
amount of transmission fluid (ATF), (DEXRON(R)VI) (fluid) that is to be charged for the flush portion of the repair should not exceed the
allowable charge for 7.5 L (2 gal) of fluid. This expense should be shown in the net item column of the warranty claim document.

The Seven digit Alpha/Numeric flow code, i.e. A10DFB2, "MUST" be written on the repair order and placed in the comments section of the
warranty claim. Any repair that requires the technician to contact the Product Quality Center (PQC) must also include the seven digit flow code.
The agent will request the seven digit flow code and add the information to the PQC case prior to providing authorization for the warranty claim.

In Canada, the Seven digit Alpha/Numeric flow code, i.e. A10DFB2, "MUST" be written on the repair order. Any repair that requires the
technician to contact the Product Quality Center (PQC) must also include the seven digit flow code. The agent will request the seven digit flow
code and add the information to the PQC case prior to providing authorization for the warranty claim.
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 600
Chevrolet Venture V6-3.4L VIN E 2925

Disclaimer
Technical Service Bulletin # 06-08-111-004B Date: 090925

06-08-111-004B - BULLETIN CANCELLATION NOTIFICATION


TECHNICAL

Bulletin No.: 06-08-111-004B

Date: September 25, 2009

Subject: Information on Discoloration, Blistering, Peeling or Erosion of Various Exterior Emblems Including Chevy Bowtie (Bulletin Cancelled)

Models:

2009 and Prior GM Passenger Cars and Trucks (including Saturn)


2003-2009 HUMMER H2
2006-2009 HUMMER H3
2005-2009 Saab 9-7X

Supercede:
This bulletin is being cancelled. Please discard Corporate Bulletin Number 06-08-111-004A (Section 08 - Body & Accessories).

This bulletin is being cancelled. The information is no longer applicable.

DisclaimerTechnical Service Bulletin # 09-08-48-006 Date: 090918

Body - Stain/Film On Windshield Glass Perimeter


TECHNICAL

Bulletin No.: 09-08-48-006

Date: September 18, 2009

Subject: Clear Stain or Film on Inside Perimeter of Windshield Glass (Clean/Polish Glass)

Models:

2010 and Prior Passenger Cars and Trucks (Including Saturn and Saab)
2010 and Prior HUMMER H2, H3

Condition

Some customers may comment on a clear stain or film on the inside of the windshield glass. This condition appears along the outer edges of the
glass along the top, bottom or A-pillar areas. Normal glass cleaning procedures will not remove the stain.

Cause

The assembly plant uses a clear sealer/primer on the outer edge of the windshield glass to improve adhesion to the urethane adhesive that bonds the
windshield glass to the vehicle body. Excess sealer/primer may drip or flow onto the windshield and cause a stain. Once the sealer/primer dries, it
may appear to have etched the glass.

Correction
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 601
Chevrolet Venture V6-3.4L VIN E 2926

Note

A "white" type of toothpaste is recommended for this repair. Gel-type toothpaste may provide less satisfactory results.

Use a small amount of toothpaste on a soft, cotton cloth to polish the stained area. It may be necessary to wrap the cloth around a paint stir stick or a
similar tool to reach the lower corners of the windshield glass.

After polishing the glass, clean the inside of the windshield glass with a clean, damp, cotton cloth and verify all of the stain is removed. Do not use
any cleaners or solvents - use only clean warm water.

Warranty Information (excluding Saab U.S. Models)

For vehicles repaired under warranty, use:

Warranty Information (Saab U.S. Models)

For vehicles repaired under warranty, use the table.

Disclaimer

Technical Service Bulletin # 03-07-29-004F Date: 090729

M/T - Operating Characteristics


INFORMATION

Bulletin No.: 03-07-29-004F

Date: July 29, 2009

Subject: Manual Transmission Operating Characteristics

Models:

2010 and Prior Passenger Cars and Light Duty Trucks (Including Saturn)
2009 and Prior Chevrolet and GMC Medium Duty Trucks
2006-2010 HUMMER H3
with Manual Transmission

Supercede:
This bulletin is being revised to add the 2010 model year and remove Isuzu from the models. Please discard Corporate Bulletin Number
03-07-29-004E (Section 07 - Transmission/Transaxle).

Important
Even though this bulletin attempts to cover operating characteristics of manual transmissions, it cannot be all inclusive. Be sure to
compare any questionable concerns to a similar vehicle and if possible, with similar mileage. Even though many of the conditions are
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 602
Chevrolet Venture V6-3.4L VIN E 2927
described as characteristics and may not be durability issues, GM may attempt to improve specific issues for customer satisfaction.

The purpose of this bulletin is to assist in identifying characteristics of manual transmissions that repair attempts will not change. The following are
explanations and examples of conditions that will generally occur in all manual transmissions. All noises will vary between transmissions due to
build variation, type of transmission (usually the more heavy duty, the more noise), type of flywheel and clutch, level of insulation, etc.

Basic Information

Many transmission noises are created by the firing pulses of the engine. Each firing pulse creates a sudden change in angular acceleration at the
crankshaft. These changes in speed can be reduced with clutch damper springs and dual mass flywheels. However, some speed variation will make
it through to the transmission. This can create noise as the various gears will accel and decel against each other because of required clearances.

Gear Rattle

Rattling or grinding (not to be confused with a missed shift type of grinding, also described as a combustion knock type of noise) type noises
usually occur while operating the engine at low RPMs (lugging the engine). This can occur while accelerating from a stop (for example, a Corvette)
or while operating at low RPMs while under a load (for example, Kodiak in a lower gear and at low engine speed). Vehicles equipped with a
dual-mass flywheel (for example, a 3500 HD Sierra with the 6-speed manual and Duramax(R)) will have reduced noise levels as compared to
vehicles without (for example, a 4500 Kodiak with the 6-speed manual and Duramax(R)). However, dual-mass flywheels do not eliminate all noise.

Neutral Rattle

There are often concerns of rattle while idling in neutral with the clutch engaged. This is related to the changes in angular acceleration described
earlier. This is a light rattle, and once again, vehicles with dual mass flywheels will have reduced noise. If the engine is shut off while idling in
neutral with the clutch engaged, the sudden stop of the engine will create a rapid change in angular acceleration that even dual mass flywheels
cannot compensate. Because of the mass of all the components, this will create a noise. This type of noise should not be heard if the clutch is
released (pedal pushed to the floor).

Backlash

Backlash noise is created when changing engine or driveline loading. This can occur when accelerating from a stop, coming to a stop, or applying
and releasing the throttle (loading and unloading the driveline). This will vary based on vehicle type, build variations, driver input, vehicle loading,
etc. and is created from the necessary clearance between all of the mating gears in the transmission, axle(s) and transfer case (if equipped).

Shift Effort

Shift effort will vary among different style transmissions and synchronizer designs. Usually the more heavy duty the transmission, the higher the
shift effort because of the increased mass of the components. Shift effort can also be higher in cold weather because the fluid will be thicker.
Medium duty transmissions will not shift as quickly as a Corvette transmission. To reduce shift effort, do not attempt to rush the shift - allow the
synchronizers to work as designed. Shifting harder will only increase the chance of rushing past the synchronizer leading to grinding while shifting.

Non-Synchronized Gears

Some light duty truck transmissions in 1st gear (creeper-gear) and reverse gears in various transmissions, along with all gears in some medium duty
transmissions, may be non-synchronized. This means there is not a mechanism to match input and output shaft speeds to allow for a smooth shift.
This function is left up to the driver. This can be noticed if a shift into 1st or reverse is attempted while the vehicle is rolling or before the input
shaft stops rotating leading to a gear grind. The grinding can be reduced by coming to a complete stop and pausing for a moment before shifting
into the 1st or reverse gear. Some slight grinding can be expected. In medium duty non-synchronized transmissions, the driver must match input
shaft (engine) speed to output shaft (driveshaft) speed with every shift. This can be accomplished by double clutching, or by using other methods. If
the driver is not able to perform this function properly, there will be gear grinding with each improperly completed shift. Driver training may be
required to correct this condition. Clutch brakes are used in medium duty non-synchronized transmissions to allow a shift into gear at a stop. The
clutch brake is used to stop the input shaft from spinning, allowing a shift into gear at a stop without grinding. The clutch brake is activated by
pressing the clutch pedal all the way to the floor. When the clutch brake is used, it is possible to have a blocked shift with the vehicle stationary. If
this occurs, engage the clutch slightly to rotate the input gear to allow the shift. The clutch brake is intended to only be used while at a stop. Care
must be taken to not activate the clutch brake while shifting between gears. This could lead to excessive grinding or a blocked or missed shift.

Skip Shift

Currently, the Cadillac CTS-V, Pontiac GTO, Chevrolet Corvette and Camaro SS (other models may follow) equipped with the 6-speed manual
transmission have a feature referred to as a "skip-shift". This feature only allows a shift from 1st to 4th gear when the indicator lamp is illuminated
on the dash. Dealers cannot disable this feature as it was established to help meet fuel economy standards. The conditions for this feature are:
engine coolant at normal operating temperature, vehicle speed of 24-31 km/h (15-19 mph), 21% or less throttle being used (refer to Service
Information or the Owner Manual for more details.)
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 603
Chevrolet Venture V6-3.4L VIN E 2928

Disclaimer

Technical Service Bulletin # 04-06-04-047I Date: 090817

Fuel System - 'TOP TIER' Detergent Gasoline Information


INFORMATION

Bulletin No.: 04-06-04-047I

Date: August 17, 2009

Subject: TOP TIER Detergent Gasoline (Deposits, Fuel Economy, No Start, Power, Performance, Stall Concerns) - U.S. Only

Models:

2010 and Prior GM Passenger Cars and Trucks (including Saturn) (U.S. Only)
2003-2010 HUMMER H2 (U.S. Only)
2006-2010 HUMMER H3 (U.S. Only)
2005-2009 Saab 9-7X (U.S. Only)

Supercede:
This bulletin is being revised to add model years and additional sources to the Top Tier Fuel Retailers list. Please discard Corporate Bulletin
Number 04-06-04-047H (Section 06 - Engine/Propulsion System). In Canada, refer to Corporate Bulletin Number 05-06-04-022F.

A new class of fuel called TOP TIER Detergent Gasoline is appearing at retail stations of some fuel marketers. This gasoline meets detergency
standards developed by six automotive companies. All vehicles will benefit from using TOP TIER Detergent Gasoline over gasoline containing the
"Lowest Additive Concentration" set by the EPA. Those vehicles that have experienced deposit related concerns may especially benefit from the
use of TOP TIER Detergent Gasoline.

Intake valve: - 10,000 miles with TOP TIER Detergent Gasoline

Intake valve: - 10,000 miles with Legal Minimum additive

Gasoline Brands That Currently Meet TOP TIER Detergent Gasoline Standards

As of August 1, 2009, all grades of the following gasoline brands meet the TOP TIER Detergent Gasoline Standards:
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 604
Chevrolet Venture V6-3.4L VIN E 2929

- Chevron
- Chevron-Canada
- QuikTrip
- Conoco
- Phillips 66
- 76
- Shell
- Shell-Canada
- Entec Stations located in the greater Montgomery, Alabama area.
- MFA Oil Company located throughout Missouri.
- Kwik Trip, Inc. in Minnesota and Wisconsin and Kwik Star convenience stores in Iowa.
- The Somerset Refinery, Inc. at Somerset Oil stations in Kentucky.
- Aloha Petroleum
- Tri-Par Oil Company
- Turkey Hill Minit Markets
- Texaco
- Petro-Canada
- Sunoco-Canada
- Road Ranger located in Illinois, Indiana, Iowa, Kentucky, Missouri, Ohio and Wisconsin

What is TOP TIER Detergent Gasoline?

TOP TIER Detergent Gasoline is a new class of gasoline with enhanced detergency. It meets new, voluntary deposit control standards developed by
six automotive companies that exceed the detergent requirements imposed by the EPA.

Where Can TOP TIER Detergent Gasoline Be Purchased?

The TOP TIER program began on May 3, 2004 and many fuel marketers have joined the program and have introduced TOP TIER Detergent
Gasoline. This is a voluntary program and not all fuel marketers will offer this product. Once fuel marketers make public announcements, they will
appear on a list of brands that meet the TOP TIER standards.

Where Can I find the Latest Information on TOP TIER Fuel and Retailers?

On the web, please visit www.toptiergas.com for additional information and updated retailer lists.

Who developed TOP TIER Detergent Gasoline standards?

TOP TIER Detergent Gasoline standards were developed by six automotive companies: Audi, BMW, General Motors, Honda, Toyota and
Volkswagen.

Why was TOP TIER Detergent Gasoline developed?

TOP TIER Detergent Gasoline was developed to increase the level of detergent additive in gasoline. The EPA requires that all gasoline sold in the
U.S. contain a detergent additive. However, the requirement is minimal and in many cases, is not sufficient to keep engines clean. In order to meet
TOP TIER Detergent Gasoline standards, a higher level of detergent is needed than what is required by the EPA. Also, TOP TIER was developed
to give fuel marketers the opportunity to differentiate their product.

Why did the six automotive companies join together to develop TOP TIER?

All six corporations recognized the benefits to both the vehicle and the consumer. Also, joining together emphasized that low detergency is an issue
of concern to several automotive companies.

What are the benefits of TOP TIER Detergent Gasoline?

TOP TIER Detergent Gasoline will help keep engines cleaner than gasoline containing the "Lowest Additive Concentration" set by the EPA. Clean
engines help provide optimal fuel economy and performance and reduced emissions. Also, use of TOP TIER Detergent Gasoline will help reduce
deposit related concerns.

Disclaimer

Technical Service Bulletin # 08-03-10-004A Date: 090724


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 605
Chevrolet Venture V6-3.4L VIN E 2930

Wheels/Tires - Accessory Wheel & Tire Information


INFORMATION

Bulletin No.: 08-03-10-004A

Date: July 24, 2009

Subject: Mounting, Balancing and Installation of Accessory Wheels and Tires Available Through GM Accessories

Models:

2010 and Prior GM Passenger Cars and Light Duty Trucks (Including Saturn, EXCLUDING Astra)
2003-2010 HUMMER H2
2006-2010 HUMMER H3

Supercede:
This bulletin is being revised to add the 2010 model year. Please discard Corporate Bulletin Number 08-03-10-004 (Section 03 - Suspension).

This bulletin is intended to offer comprehensive instructions to GM Dealers and authorized GM Accessory Distributor/Installers as to the proper
methods for mounting, balancing, and installing accessory wheels and tires. Adherence to these methods will ensure that the vehicle delivered to the
customer is of the highest quality.

Tire Pressure Monitor (TPM) Sensor Installation

1. Clean any dirt or debris from the grommet sealing area.

2. Insert the sensor in the wheel hole with the air passage facing away from the wheel
3. Install the sensor nut and position the sensor body parallel to the inside wheel surface while tightening the nut.

Tighten
Tighten the sensor nut to 7 Nm (62 lb in).

Tire Mounting

Important
When mounting the tires, use the approved tire mounting lubricant. DO NOT use silicon or corrosive base compounds to lubricate the tire
bead and the wheel rim. A silicon base compound can allow the tire to slip on the rim resulting in imbalance or braking failure. A corrosive
type compound can cause tire or rim deterioration.

1. Verify that the tire is at least 15°C (60°F) prior to mounting and inflating.
2. Apply GM Vehicle Care Rubber Lubricant, P/N 12345884 (Canadian P/N 5728223), to both of the tire beads and both of the wheel bead
hump areas for full circumference.

Important
Mounting operation and wheel assembly must be completed within 15 minutes of applying lubricant to ensure proper assembly and
inflation. Excess lubricant (drips and runs) in the tire must be avoided as it affects balance and may cause tire slippage on wheels
during vehicle operation.
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 606
Chevrolet Venture V6-3.4L VIN E 2931

3. Position the rim so the TPM valve stem (1) is situated at the 3 o'clock position relative to the head (2). This will protect the TPM sensor body
by ensuring that the bead is under the least amount of tension when it passes over it.

Important
Some GM Accessory wheels have a "reverse-rim" design and will be marked as such. "Reverse-rim" wheels should be positioned
face-down for tire mounting, taking care not to damage the face of the wheel.

4. Using the tire changer, rotate the tire/wheel assembly clockwise when transferring the tire bead to the inside of the wheel rim.
5. After the bottom bead is on the wheel, reposition the wheel and tire so that the TPM valve stem is again situated at the 3 o'clock position
relative to the head. This will protect the sensor while mounting the tire bead to the outside of the wheel.

6. Using the tire changer, rotate the tire/wheel assembly clockwise when transferring the tire bead to the inside of the wheel rim.

Danger
To avoid serious personal injury, do not stand over the tire when inflating. The bead may break when the bead snaps over the safety
hump. Do not exceed 40 psi (275 kPa) pressure when inflating any tire if beads are not seated. If 40 psi (275 kPa) pressure will not
seat the beads, deflate, relubricate the beads and reinflate. If greater than 40 psi (275 kPa) is required to install the tire on the wheel,
a safety cage must be used. Overinflation may cause the bead to break and cause serious personal injury.

7. Inflate the tire until it passes the bead humps. Be sure that the valve core is not installed at this time.
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 607
Chevrolet Venture V6-3.4L VIN E 2932
8. Install the valve core to the TPM's valve stem.
9. Set the inflation pressure to 40 psi (275 kPa). It will be readjusted to the proper placard pressure when it is installed on the vehicle. This
higher pressure allows for losses due to temperature change or any leakage that may occur prior to installation on the vehicle.

Important
Aggressive accelerating and braking should be avoided for the first 24 hours after the tires have been mounted to avoid the tire slipping on
the rim.

Calibration of Tire/Wheel Balancer

Tire/wheel balancing equipment should be checked for proper calibration every two weeks. Check the calibration of the tire and wheel assembly
balancer according to the manufacturer's recommendations or perform the following test:

Important
If the balancer fails any of the steps in this calibration test, the balancer should be calibrated according to the manufacturer's
instructions. If the balancer cannot be calibrated, contact the manufacturer for assistance.

1. Spin the balancer without a wheel or any of the adapters on the shaft.
2. Inspect the balancer readings.

Specification
Zero within 0.25 oz (7 g).

3. If the balancer is within the specification range, balance a tire and wheel assembly - that is within radial and lateral runout tolerances - to
ZERO, using the same balancer.
4. After the tire and wheel assembly has been balanced, add a 3 oz (85 g) test weight to the wheel at any location.
5. Spin the tire and wheel assembly again. Note the readings.

- In the static and dynamic modes, the balancer should call for 3 oz (85 g) of weight, 180 degrees opposite the test weight.
- In the dynamic mode, the weight should be called for on the flange of the wheel opposite the test weight.

6. With the assembly imbalanced to 3 oz (85 g), cycle the balancer five times.
7. Inspect the balancer readings:

Specification
Maximum variation: 0.25 oz (7 g).

8. Index the tire and wheel assembly on the balancer shaft 90 degrees from the previous location.
9. Cycle the balancer with the assembly at the new location.
10. Inspect the balancer readings:

Specification
Maximum variation: 0.25 oz (7 g).

11. Repeat Steps 8 through 10 until the tire and wheel assembly has been cycled and checked at each of the 4 locations on the balancer shaft.

Tire and Wheel Balancing

1. Follow the balancer manufacturer's instructions to mount the wheel and tire assembly on the balancer.
2. Perform a dynamic balance on the tire and wheel per the manufacturer's instructions (dynamic balance is sometimes referred to as "couple"
balance). This will indicate the correct amount of balance weight to add at two positions on the wheel.
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 608
Chevrolet Venture V6-3.4L VIN E 2933

Adhesive Weight

Clip-On Weight
3. Install a clip-on balance weight on the inboard wheel flange per the weight indications on the balancer.

- Use only MC-series polyester-coated weights at this location. GM Accessory wheels have an MC-rim contour at the inboard location.
- Use only a nylon or plastic tipped hammer to avoid damaging the weight coating or the wheel finish.
- Never strike a wheel weight more than twice. If it doesn't seat properly after two hits, discard it and try a new weight.

Wheel Rim Profile with Adhesive Weight Locations Shown

Important
Some older GM Accessory wheels may be MC style rims both inboard and outboard and should, therefore, use clip-on MC weights
in both positions. Some GM Accessory wheels may be flangeless on the inboard side. In this case, follow the instructions for applying
adhesive balanced weights. Place the adhesive weight on the face of the rim inner surface, as far inboard as possible (2).

4. Install adhesive balance weights at the outboard location (1) on the wheel per the weight indications on the balancer.

- Both the wheel and the weights must be at least 15°C (60°F).
- The area where the weights will be applied must be clean and dry. Wipe the area with a 50/50 mixture, by volume, of isopropyl alcohol
and clean water using a clean cloth. Allow to dry completely.
- Install adhesive weights just inboard of the wheel face on the rim inner surface.
- Apply a force of 21 lb (90 N) to the weights to achieve proper adhesion. This is very important to achieve proper adhesion.

Balance Weight Limits

When dynamically balancing a wheel and tire assembly, the maximum amount of balance weight that should be used at any one location on a wheel
is 5 oz (141 g). This means a maximum of 5 oz (141 g) on the outboard flange (or behind the wheel face, if adhesive weight is used), and maximum
of 5 oz (141 g) on the inboard flange (or on the inner rim surface).

If the balancer calls for greater than 5 oz (141 g) n either position, perform the following steps to reduce the weight:

1. Mark the valve stem location on the tire.


2. Deflate the tire/wheel assembly.
3. Remove any existing balance weights.
4. Rotate tire 180 degrees on the wheel.
5. Re-inflate tire/wheel assembly and rebalance.
6. If the tire/wheel assembly still requires more than 5 oz (141 g) per plane, repeat Steps 1-4, rotating the tire 90 degrees from its original
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 609
Chevrolet Venture V6-3.4L VIN E 2934
position.
7. If the tire/wheel assembly still requires more than 5 oz (141 g) per plane, repeat Steps 1-4, rotating the tire 270 degrees from its original
position.
8. If tire/wheel assembly still requires more than 5 oz (141 g) per plane, remove the tire from the wheel, remove all wheel weights and TPM
sensor, and check static balance of the wheel.

Important
This is a static balance check only. The operating mode of the balancer must be changed from "dynamic or couple" to "static". The
balancer should feed back only a single weight value when in static mode.

- If static balance of wheel is 4 oz (113 g) or less, re-use wheel and reject the tire for excessive imbalance.
- If static balance of the wheel is greater than 4 oz (113 g), re-use the tire and reject the wheel for excessive imbalance.

Tire Pressure Monitor Sensor Learn

When installing GM Accessory wheels and tires on a vehicle that have new TPM sensors installed in them, it is necessary to learn the new sensor
identification codes/locations into the vehicle's module. If the relearn procedure is not performed properly, the module will continue to try to
communicate with the original sensors that were removed from the vehicle. This will result in the vehicle displaying a TPM system malfunction
message once the vehicle is removed from the proximity of the original sensors for an extended period of time. Please see the Tire Pressure Sensor
Learn procedure in SI for the vehicle specific instructions.

Tire Inflation Pressure and Placards

Tire Placard

When installing GM Accessory wheels and tires on a vehicle, the new tire pressure placard (supplied with the GM Accessory wheel kit) must be
installed over the existing placard inside the driver's side door frame. This is required when the size of the GM Accessory tires is different than
those being removed from the vehicle.

The new tire placard should be located within the red box, over the top of the original tire label found on the door jamb. To locate the placard
within the red box use the upper left hand edge of the red line as a guide. When properly placed, the new tire placard will obscure the original tire
information. Be sure that the surface is clean and dry, and the surface temperature is not less than 21°C (65°F).

Tire Inflation Pressure

Note the front, rear, and spare (where applicable) tire inflation pressures shown on the new tire placard. The inflation pressure of new tires on the
vehicle must be adjusted to the values shown on the placard. Even if the tire size was not changed on the vehicle and the tire pressure placard was
not replaced, all of the tires must have their inflation pressures adjusted to match those shown on tire pressure placard.

Electronic Module Reprogramming for Proper Tire Inflation Pressure

When GM Accessory wheels and tires are installed on a vehicle that requires a different tire inflation pressure according to the Tire Inflation
Placard, the vehicle must be updated with the new pressure and tire type (P or LT). If this is not done the vehicle will incorrectly report low or high
tire pressure conditions incorrectly. Please see the Corporate Bulletin specific to the vehicle and wheel/tire application for detailed information on
updating of the tire type/pressure.

Other Electronic Module Reprogramming

For proper vehicle operation and to ensure coverage under the provisions of the new vehicle warranty, the vehicle may require that certain control
modules be reprogrammed with the correct calibrations as soon as the GM Accessory wheels and tires are installed. Examples of the modules that
may be affected are Electronic Brake Control Module (for proper anti-lock brake and stability control performance) and Engine Control Module
(for proper speedometer/odometer function).

Please see the Corporate Bulletin specific to the vehicle and wheel/tire application for detailed information on module reprogramming.

Disclaimer

Technical Service Bulletin # 03-03-10-007E Date: 090805

Wheels/Tires - OE Tire/Wheel Characteristics


INFORMATION
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 610
Chevrolet Venture V6-3.4L VIN E 2935

Bulletin No.: 03-03-10-007E

Date: August 05, 2009

Subject: Information on Tire/Wheel Characteristics (Vibration, Balance, Shake, Flat Spotting) of GM Original Equipment Tires

Models:

2010 and Prior GM Passenger Cars and Light Duty Trucks (Including Saturn)
2010 and Prior HUMMER H2, H3
2009 and Prior Saab 9-7X

Supercede:
This bulletin is being revised to include additional model years. Please discard Corporate Bulletin Number 03-03-10-007D (Section 03 -
Suspension).

The purpose of this bulletin is to help explain that , under certain circumstances, a customer may notice a slight tire shake within the first few
miles/kilometers of vehicle operation.

Tires may be designed with a nylon overlay configuration engineered to enhance the tire's integrity at high speeds. This allows the tires to be driven
at higher speeds without excessive heat buildup.

Important
Before measuring tires on equipment such as the Hunter GSP 9700, the vehicle MUST be driven a minimum of 26 km (15 mi) to ensure
removal of any flat spotting (The tendency to "flat spot" is less likely as the tire accumulates mileage).

When parked overnight, or for a period of time, the tires may set (flat spot) and require a few miles/kilometers before heating up to their normal
operating temperature. Until the tires warm up, a slight tire shake may be felt but should subside quickly.

Important
DEALERS SHOULD REFRAIN FROM ATTEMPTING REPAIRS OR REPLACING COMPONENTS for this temporary tire flat
spotting condition.

Disclaimer

Technical Service Bulletin # 06-02-32-013B Date: 090807

Steering - Power Steering Pump Replacement Tips


INFORMATION

Bulletin No.: 06-02-32-013B

Date: August 07, 2009

Subject: Diagnostic Tips/Recommendations When Power Steering Pump Replacement is Necessary

Models:

1997-2010 GM Passenger Cars and Light Duty Trucks (including Saturn)


2010 and Prior HUMMER H2, H3
2005-2009 Saab 9-7X

Supercede:
This bulletin is being revised to add model years and update the information. Please discard Corporate Bulletin Number 06-02-32-013A (Section 02
- Steering).

A recently completed analysis of returned power steering (PS) pumps that had been replaced for noise, no power assist, no or low pressure and
leaking conditions has indicated a high number of "No Trouble Found" results.

Corporate Bulletin Number 01-02-32-004 indicates that when attempting to repair a power steering concern, the steering system analyzer should be
utilized to assist the technician in a successful diagnosis. Note- Saturn ASTRA does not utilize the Power Steering System Analyzer.
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 611
Chevrolet Venture V6-3.4L VIN E 2936

In addition, extensive warranty analysis has shown that the following situations are all significant root causes of PS pump failures:

- Improper pulley installation


- Re-using the O-rings
- Using fluid other than the OE-specified steering fluid
- Failure to flush the PS system

In order to help improve customer satisfaction and reduce comebacks, GM recommends the following tips for replacing a PS pump:

1. Low or no pressure from the PS pump may be the results of dirty or contaminated fluid, which could cause the pressure relief valve to stop
functioning. Using the proper tools, flush and bleed the PS system. Any residual contaminants will result in pump failure.
2. When removing the pulley, use the proper special tools. Because the pulley alignment is critical, distorting the pulley may damage bearings
on the new PS pump.

Note
Some new PS pumps may not include a new O-ring. Please refer to the appropriate Parts Catalog. Saturn retailers should refer to the
appropriate model year Parts & Illustration Catalog for the vehicle.

3. Be sure to use only the new O-rings included with the PS pump. The new reservoir O-ring must be lubricated with OE-specific PS fluid prior
to installation. Also make sure that the control valve O-ring is in its exact groove position and is NOT covering the pressure bypass hole.
4. Bleed the PS system according to the procedures/recommendations in SI.

Following these procedures and using the correct tools and fluids should help ensure that the new PS pump operates properly. Skipping steps may
cost you time and trouble later.

Disclaimer

Technical Service Bulletin # 06-08-64-001B Date: 091020

Body - Side Window Chipping Information


INFORMATION

Bulletin No.: 06-08-64-001B

Date: October 20, 2009

Subject: Information on Side Door Window Glass Chipping Caused by Hanging Vehicle Key Lock Box

Models:

2010 and Prior Passenger Cars and Trucks (Including Saturn)


2010 and Prior HUMMER H2, H3
2009 and Prior Saab 9-7X

Supercede:
This bulletin is being revised to add vehicles and model years and to include all types of door window glass. Please discard Corporate Bulletin
Number 06-08-64-001A (Section 08 - Body & Accessories).

- In several warranty parts review cases, side door window glass was observed with a chip or chips on the top side of the window glass. Dealer
contacts confirmed that they use a vehicle key lock box on the front side door window glass.
- A random selection of side door glass returns will be conducted to confirm adherence. If a side door glass is discovered with a chip or chips
in the location previously described, the side door glass will be returned to the dealership for debit.
Example of Side Door Glass
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 612
Chevrolet Venture V6-3.4L VIN E 2937

- DO NOT place a vehicle key lock box on a side door window glass.

Disclaimer

Technical Service Bulletin # 99-04-20-002F Date: 091103

Drivetrain - Clunk Noise Shifting From PARK Into Gear


INFORMATION

Bulletin No.: 99-04-20-002F

Date: November 02, 2009

Subject: Information on Driveline Clunk Noise When Shifting Between PARK and DRIVE, PARK and REVERSE or DRIVE and REVERSE

Models:

2010 and Prior GM Passenger Cars and Light Duty Trucks (including Saturn)
2010 and Prior HUMMER H2, H3
2009 and Prior Saab 9-7X

Supercede:
This bulletin is being revised to add current model years. Please discard Corporate Bulletin Number 99-04-20-002E (Section 04 - Driveline/Axle).

Important
The condition described in this bulletin should not be confused with the following previous bulletins:
- Info - Discontinue Flushing and Replacing Transfer Case Fluid Due to Bump/Clunk Concern (Corporate Bulletin Number
99-04-21-004B)
- Clunk, Bump or Squawk when Vehicle Comes to Complete Stop or Accelerating from Complete Stop (Replace Rear Drive Shaft
Nickel-Plated Slip Yoke) (Corporate Bulletin Number 01-04-17-004B)
- Clunk Noise at Stop or From Launch (Clean/Lubricate Rear Propshaft Slip Yoke Splines) (Corporate Bulletin Number
09-04-21-003B)
- Bump Feel/Clunk Noise at Stop or From Launch (Clean/Lubricate Propeller Shaft Slip Yoke Splines) (Corporate Bulletin Number
09-04-17-002)

Some customers of vehicles equipped with automatic transmissions may comment that the vehicle exhibits a clunk noise when shifting between
Park and Drive, Park and Reverse, or Drive and Reverse. Similarly, customers of vehicles equipped with automatic or manual transmissions may
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 613
Chevrolet Venture V6-3.4L VIN E 2938
comment that the vehicle exhibits a clunk noise while driving when the accelerator is quickly depressed and then released.

Note

Compare this complaint vehicle to a like vehicle. If the results are the same, this is a normal condition. For additional diagnostic information, refer
to the appropriate Service information.

Whenever there are two or more gears interacting with one another, there must be a certain amount of clearance between those gears in order for
the gears to operate properly. This clearance or freeplay (also known as lash) can translate into a clunk noise whenever the gear is loaded and
unloaded quickly, or whenever the direction of rotation is reversed. The more gears you have in a system, the more freeplay the total system will
have.

The clunk noise that owners sometimes hear may be the result of a buildup of freeplay (lash) between the components in the driveline.

For example, the potential for a driveline clunk would be greater in a 4-wheel drive or all-wheel drive vehicle than a 2-wheel drive vehicle. This is
because in addition to the freeplay from the rear axle gears, the universal joints, and the transmission (common to both vehicles), the 4-wheel drive
transfer case gears (and their associated clearances) add additional freeplay to the driveline.

In service, dealers are discouraged from attempting to repair driveline clunk conditions for the following reasons:

- Comments of driveline clunk are almost never the result of one individual component with excessive lash, but rather the result of the added
affect of freeplay (or lash) present in all of the driveline components.
Because all of the components in the driveline have a certain amount of lash by design, changing driveline components may not result in a
satisfactory lash reduction.
- While some owners may find the clunk noise objectionable, this will not adversely affect durability or performance.
- For additional diagnostic information, refer to the appropriate Service Information.

Disclaimer

Technical Service Bulletin # 99-08-51-007D Date: 100114

Wheel - Refinishing Aluminum Wheels


INFORMATION

Bulletin No.: 99-08-51-007D

Date: January 14, 2010

Subject: Refinishing Aluminum Wheels

Models:

2010 and Prior Passenger Cars and Trucks (Including Saturn)


2003-2010 HUMMER H2
2006-2010 HUMMER H3
2005-2009 Saab 9-7X

Supercede:
This bulletin is being revised to add additional model years and remove one outside company reference. Please discard Corporate Bulletin Number
99-08-51-007C (Section 08 - Body and Accessories).

This bulletin updates General Motor's position on refinishing aluminum wheels. GM does not endorse any repairs that involve welding, bending,
straightening or re-machining. Only cosmetic refinishing of the wheel's coatings, using recommended procedures, is allowed.

Evaluating Damage

In evaluating damage, it is the GM Dealer's responsibility to inspect the wheel for corrosion, scrapes, gouges, etc. The Dealer must insure that such
damage is not deeper than what can be sanded or polished off. The wheel must be inspected for cracks. If cracks are found, discard the wheel. Any
wheels with bent rim flanges must not be repaired or refinished. Wheels that have been refinished by an outside company must be returned to the
same vehicle. The Dealer must record the wheel ID stamp or the cast date on the wheel in order to assure this requirement. Refer to Refinisher's
Responsibility - Outside Company later in this bulletin.
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 614
Chevrolet Venture V6-3.4L VIN E 2939

Aluminum Wheel Refinishing Recommendations


- Chrome-plated aluminum wheels
Re-plating these wheels is not recommended.
- Polished aluminum wheels
These wheels have a polyester or acrylic clearcoat on them. If the clearcoat is damaged, refinishing is possible. However, the required
refinishing process cannot be performed in the dealer environment. Refer to Refinisher's Responsibility - Outside Company later in this
bulletin.
- Painted aluminum wheels
These wheels are painted using a primer, color coat, and clearcoat procedure. If the paint is damaged, refinishing is possible. As with
polished wheels, all original coatings must be removed first. Media blasting is recommended. Refer to GM Aluminum Refinishing Bulletin
#53-17-03A for the re-painting of this type of wheel.
- Bright, machined aluminum wheels
These wheels have a polyester or acrylic clearcoat on them. In some cases, the recessed "pocket" areas of the wheel may be painted. Surface
refinishing is possible. The wheel must be totally stripped by media blasting or other suitable means. The wheel should be resurfaced by
using a sanding process rather than a machining process. This allows the least amount of material to be removed.

Important
Do not use any re-machining process that removes aluminum. This could affect the dimensions and function of the wheel.

Painting is an option to re-clearcoating polished and bright machined aluminum wheels. Paint will better mask any surface imperfections and is
somewhat more durable than clearcoat alone. GM recommends using Corsican SILVER WAEQ9283 for a fine "aluminum-like" look or Sparkle
SILVER WA9967 for a very bright look. As an option, the body color may also be used. When using any of the painting options, it is
recommended that all four wheels be refinished in order to maintain color uniformity. Refer to GM Aluminum Refinishing Bulletin #53-17-03A for
specific procedures and product recommendations.

Refinisher's Responsibility - Outside Company

Important
Some outside companies are offering wheel refinishing services. Such refinished wheels will be permanently marked by the refinisher and
are warranted by the refinisher. Any process that re-machines or otherwise re-manufactures the wheel should not be used.

A refinisher's responsibility includes inspecting for cracks using the Zyglo system or the equivalent. Any cracked wheels must not be refinished. No
welding, hammering or reforming of any kind is allowed. The wheel ID must be recorded and follow the wheel throughout the process in order to
assure that the same wheel is returned. A plastic media blast may be used for clean up of the wheel. Hand and/or lathe sanding of the machined
surface and the wheel window is allowed. Material removal, though, must be kept to a minimum. Re-machining of the wheel is not allowed. Paint
and/or clear coat must not be present on the following surfaces: the nut chamfers, the wheel mounting surfaces and the wheel pilot hole. The
refinisher must permanently ID stamp the wheel and warrant the painted/clearcoated surfaces for a minimum of one year or the remainder of the
new vehicle warranty, whichever is longer.

Important
Whenever a wheel is refinished, the mounting surface and the wheel nut contact surfaces must not be painted or clearcoated. Coating these
surfaces could affect the wheel nut torque.

When re-mounting a tire on an aluminum wheel, coated balance weights must be used in order to reduce the chance of future cosmetic damage.

DisclaimerTechnical Service Bulletin # 06-08-43-003B Date: 091111

Wipers/Washers - Windshield Wiper Maintenance/Cleaning


INFORMATION

Bulletin No.: 06-08-43-003B

Date: November 11, 2009

Subject: Windshield Wiper Performance, Cleaning Instructions and Maintenance

Models:

2010 and Prior GM Passenger Cars and Trucks (including Saturn)


2010 and Prior HUMMER H2, H3
2010 and Prior Isuzu Medium Duty Trucks
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 615
Chevrolet Venture V6-3.4L VIN E 2940
2005-2009 Saab 9-7X

Supercede:
This bulletin is being revised to add the 2010 model year. Please discard Corporate Bulletin Number 06-08-43-003A (Section 08 - Body and
Accessories).

Wiper Concerns

Most concerns about windshield wiper performance are the result of dirty wiper blades, damaged wiper blades, or worn out blades that are
continuing to be used beyond their useful life. Depending on environmental conditions, wiper blades can have dramatic differences in lifespan.
Here are some tips and guidelines to maximize wiper performance to avoid damage to the blades, and to avoid unnecessary replacements.

Many wiper blades are being replaced under warranty with reviews showing there is nothing wrong with the returned blades other than a build-up
of dirt. Additionally, advise the customer to review the information in their Owner Manual.

Inspection and Cleaning

Scheduled Maintenance
- Inspect your wipers rubber blades every 4-6 months or 12,000 km (7,500 mi) for wear, cracking or contamination.
- Clean the windshield and the rubber wiper blades (using the procedure below) if the blades are not clearing the glass satisfactorily. If this
does not correct the problem, then replace the rubber elements.

Cleaning Procedure

Important
Avoid getting windshield washer fluid on your hands. Wear rubber gloves or avoid direct contact with washer fluid.

Important
Do not use gasoline, kerosene, or petroleum based products to clean wiper blades.

- Clean the rubber blades using a lint free cloth or paper towel soaked with windshield washer fluid or a mild detergent. You should see
significant amounts of dirt being removed on the cloth.
- Be sure to wash the windshield thoroughly when you clean the blades. Bugs, road grime, sap and a buildup of car wash/wax treatments may
additionally cause wiper streaking.
Tip
For a larger scale buildup on the windshield, use a non-abrasive cleaner such as Bon-Ami* (www.faultless.com) cleanser with a wet sponge,
being sure to use plenty of water to avoid scratching the glass. Flush the surface and body panels completely.

Tip
For day-to-day exterior glass cleaning and to maintain a streak free appearance, suggest Vehicle Care Glass Cleaner, P/N 89021822 (in
Canada, 992727). This product is an easy to use foaming cleaner that quickly removes dirt and grime from glass surfaces.

Tip
Interior glass should be cleaned with plain, clean water to eliminate any film or haze on the window and help prevent fogging, a major
customer dissatisfier. Refer to Corporate Bulletin Number 03-00-89-006D for more information. The New Vehicle Pre-Delivery Inspection
form also recommends using plain water to clean interior glass.

*"We believe this material to be reliable. There may be additional manufacturers of such material. General Motors does not endorse, indicate any
preference for or assume any responsibility for the products or equipment from these firms or any such items which may be available from other
sources.

Avoiding Wiper Damage

The following are major contributors to wiper damage. Some of these you can control and others are environmental concerns.

- Extremely dusty areas (such as driving on dirt roads) may cause the wipers rubber edge to wear quickly and unevenly.
- Sand and salt used on roads for increasing winter traction and ice control will cause the wiper blades to wear quicker. Areas with significant
snowfall require more frequent blade replacements.
- Heat and time may cause the rubber blades to take a "permanent set" resulting in the rubber not flexing and turning over uniformly. This
condition may result in streaking and/or unwiped areas.
- Rubber blades are easily cut or torn when using ice scrapers. Likewise pulling blades up off a frozen windshield can tear the rubber. Exercise
caution when clearing ice and snow.
- Using your wipers to "wear through" frost and ice, instead of allowing the defrosters to melt the ice, can dull, nick or tear the rubber blades.
- Banging wipers on the glass to remove ice and snow may cause the blade to bend, dislodging the rubber and causing potential scratching of
the windshield.
- Ice can form in the pin joints of the wipers, which can cause streaking and unwiped areas. To remove ice from pin joints, compress the blade
and rubber edge with your hand to loosen the frozen joints. Consider using Winter Blades that have a rubber cover to avoid this condition.
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 616
Chevrolet Venture V6-3.4L VIN E 2941

Disclaimer

Technical Service Bulletin # 09-03-10-017 Date: 091217

Wheels/Tires - Replacement Wheel Weight Information


INFORMATION

Bulletin No.: 09-03-10-017

Date: December 17, 2009

Subject: Information on Replacement Wheel Weights

Models:

2010 and Prior GM Passenger Cars and Light Duty Trucks (including Saturn)
2010 and Prior HUMMER H2, H2 SUT, H3

Important
GM recommends that all dealers replace any existing inventory of lead wheel weights with approved, non-lead weights. The EPA and some
states (particularly California) are pressuring for the elimination of lead wheel weights. California dealers who continue to use lead wheel
weights after December 31, 2009 may be subject to suit under Proposition 65. If lead weights are scrapped, GM suggests they be sent to a
lead recycler for proper disposal.

Wheel Weights Available from GMSPO

GM has replaced all former styles of wheel weights with two designs of lead-free, clear-coat safe, adhesive-backed weights. The first design
replaces all "clip-on" style of weights and the second replaces all "stick-on" styles.

Important
The wheels must be cleaned prior to installation of any adhesive weights. Failure to properly clean the wheels may result in poor adhesion
of the weights.

"Clip-On" Adhesive Wheel Weight Replacements

The "clip-on" style comes on a roll and is "cut to length". The packaging of the wheel weight has a ruler on the box to measure the proper length of
material to achieve any desired amount of weight required. It is affixed to the wheel in the same location as a traditional clip-on weight would but
utilizes an adhesive instead of the mechanical clip. The weight does not damage clear-coated surfaces.

"Stick-On" Adhesive Wheel Weight Replacements

The "stick-on" weight is 0.17 g (6 oz) in total mass, constructed of 24 individual 0.007 g (0.25 oz) weights. It is affixed to the wheel in the same
location as a traditional stick on weight positioned in the interior of the wheel. The weight is low profile and does not diminish proper caliper to
wheel clearances. You may use as much or as little of the 0.17 g (6 oz) total weight of the product as required and more product may be used if the
application calls for additional weight.

Parts Information

Disclaimer
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 617
Chevrolet Venture V6-3.4L VIN E 2942

Technical Service Bulletin # 03-08-48-006G Date: 100226

A/C - Window Defroster Contact/Tab Repair Information


INFORMATION

Bulletin No.: 03-08-48-006G

Date: February 25, 2010

Subject: Repair Information for Reconnection of Rear Window Defroster Contact or Tab

Models:

2000-2010 GM Passenger Cars and Trucks (including Saturn)


2003-2009 HUMMER H2
2006-2010 HUMMER H3
2005-2009 Saab 9-7X
2007-2010 Opel GT
2007-2008 Daewoo G2X
Equipped With Electric Rear Window Defroster - RPO C49

Supercede:
This bulletin is being revised to add the 2010 model year. Please discard Corporate Bulletin Number 03-08-48-006F (Section 08 - Body and
Accessories).

Repair Suggestions

Soldering Defroster Contact Tabs

In many cases the terminal tab will still be in the connector when you examine the vehicle. For Chevrolet Tahoe, Suburban, GMC Yukon, and
Cadillac Escalade vehicles (with moveable glass), always replace the defroster tab (GM P/N 25916031) and the defroster electrical power connector
(P/N 12034110). For all other vehicles, reconnect the original defroster tab.

In most applications it is preferable to create a new solder connection to reattach a separated rear defroster tab. If you take note of the steps below,
it is possible to create a new solder joint that is equal to, or stronger than, the original. The generic procedure below is not very time intensive, but
does include minor preparation work to create a good bonding surface. Be sure to follow each of the steps, as combined they will produce the
strongest bond possible. Please consider the following before attempting the repair:

- Soldering introduces significant heat to the glass window of the vehicle. When performing the re-connection of the tab, use only the heat
required to do the job. Pre-heat the soldering iron and have the solder in your other hand, ready to go, the moment you have enough heat to
melt the solder.
- If it is winter, bring the vehicle into the service garage and remove any snow from the back window area. Allow time for the glass to warm to
the temperature inside the building. Soldering creates a "hot spot" in the glass. DO NOT solder on cold glass.

Caution
Heating the glass excessively, or repeatedly without time to cool, may result in glass breakage. ALWAYS wear safety glasses when
performing this repair!

- You MUST use a silver-bearing solder to make the connection. DO NOT attempt this repair with conventional tin/lead alloy solders. Silver
bearing solder will adhere to the electrical buss bar, making a strong and lasting repair.
- Protect surfaces under the area to be soldered. It is very easy to drip solder when performing this repair. Pacing a shop towel under the
soldering area is sufficient protection.

Soldering Procedure
1. It is imperative to remove and replace the rear defroster electrical power connector by crimping a new connector to the feed wire. The proper
connector P/N 12034110 can be found in the Packard Electrical Assortment, Tray 18, Position 5.

- Insert Delphi pick 12094430 to depress the locking tab on the terminal.
- Insert Delphi pick 12094429 to release the secondary lock tab.

Important
DO NOT re-use the existing defroster tab on new-style full-size utility vehicles with moveable glass.

2. Connect the electrical connector to the defroster tab. Fully engage the connector. An improperly seated connector may cause excessive
resistance and impede the proper operation of the defroster. Add a small bead of solder to mate the electrical connector tab to the defroster
tab.
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 618
Chevrolet Venture V6-3.4L VIN E 2943

3. Prepare the surface of the used defroster tab (not required for new tabs on new-style full-size utility models) and the defroster buss bar with
fine grain (500 grit) sandpaper or Emery cloth. It is not necessary to remove all of the original solder, but it should be scuffed sufficiently so
that no oxidation is present. The photo above shows a close up of a properly prepared surface.
Tip
You may want to mask the glass around the contact area with tape. This is easy to do and will allow you to safely prepare the contact surface
without the risk of scratching the glass or the black painted shading.

Important
Most rear glass has a black painted masking around the edge of the glass. When cleaning up the connection surface, be very careful
not to damage the surface of the black shading or the surface of the glass.

4. Wipe the newly prepared contact area with Kent Automotive* Acrysol(TM) (or equivalent) to remove any residual oil or dirt.

Important
You MUST use a silver-bearing solder to make the solder joint. DO NOT attempt this repair with conventional tin/lead alloy solders.
Most suppliers have this type of solder available and it is available nationally at Radio Shack(R)*. It is sold in several diameters and either
are acceptable for this repair.

5. For this step, it is permitted that two technicians be used if required. Heat the new connector on the surface of the buss bar that is to be
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 619
Chevrolet Venture V6-3.4L VIN E 2944
soldered. Long nose pliers are suggested to hold the electrical connector and the defroster tab in place. Keep the solder ready and begin
flowing out the solder as soon as the melting temperature has been reached.
Tip
If a single technician is attempting this repair, it is beneficial to wrap one turn of the solder around the new contacts base. In this manner, as
the melting point of the solder is reached, a layer is deposited on the bottom side of the contact.

Important
Try to align the new contact so that it is positioned with the same orientation as the original contact.

6. The above illustrates an ideal finished solder joint. Additional stray solder will not harm the performance of the bond; however, while it is
unlikely that customers may refer to the appearance of the rear window defroster and its components as a positive styling feature of the
vehicle interior, it is easy to elicit the opposite reaction due to a poor cosmetic application.

*We believe this source and their products to be reliable. There may be additional manufacturers of such products/materials. General Motors does
not endorse, indicate any preference for, or assume any responsibility for the products or material from this firm or for any such items that may be
available from other sources.

Parts Information

Acrysol(TM) can be ordered directly from Kent Automotive at 1-800-654-6333 (in Canada, 1-800-563-1717).

Radio Shack(R) products can be found nationally at retail locations, www.radioshack.com, or at 1-800-843-7422.

In Canada, use The Source by Circuit City(TM) - www.thesourcecc.ca or telephone 1-866-454-4426 (for English) or 1-866-544-4431 (for French),
or at an equivalent retail location.

All other parts can be ordered through GMSPO or SSPO.

Warranty Information (excluding Saab U.S. Models)

For vehicles repaired under warranty, use:

Warranty Information (Saab U.S. Models)

For vehicles repaired under warranty, use the table above.


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 620
Chevrolet Venture V6-3.4L VIN E 2945

Disclaimer

Technical Service Bulletin # 04-06-01-029E Date: 100429

Vehicle - Engine Crankcase and Subsystems Flushing Info.


INFORMATION

Bulletin No.: 04-06-01-029E

Date: April 29, 2010

Subject: Unnecessary Flushing Services, Additive Recommendations and Proper Utilization of GM Simplified Maintenance Schedule to Enhance
Customer Service Experience

Models:

2011 and Prior GM Passenger Cars and Trucks (including Saturn)


2010 and Prior HUMMER H2, H3
2005-2009 Saab 9-7X

Supercede:
This bulletin is being revised to update the model years and add information about the proper transmission flush procedure. Please discard
Corporate Bulletin Number 04-06-01-029D (Section 06 - Engine/Propulsion System).

An Overview of Proper Vehicle Service

General Motors is aware that some companies are marketing tools and equipment to support a subsystem flushing procedures. These dedicated
machines are in addition to many engine oil, cooling system, fuel system, A/C, transmission flush and steering system additives available to the
consumer. GM Vehicles under normal usage do not require any additional procedures or additives beyond what is advised under the former Vehicle
Maintenance Schedules or the current Simplified Maintenance Schedules. Do not confuse machines available from Kent-Moore/SPX that are
designed to aid and accelerate the process of fluid changing with these flushing machines.

Engine Crankcase Flushing

General Motors Corporation does not endorse or recommend engine crankcase flushing for any of its gasoline engines. Analysis of some of the
aftermarket materials used for crankcase flushing indicate incompatibility with GM engine components and the potential for damage to some
engine seals and bearings. Damage to engine components resulting from crankcase flushing IS NOT COVERED under the terms of the New
Vehicle Warranty.

GM Authorized Service Information: Detailed, Descriptive, and Complete

If a specific model vehicle or powertrain need is identified, GM will issue an Authorized Service Document containing a procedure and, if required,
provide, make available, or require the specific use of a machine, tool or chemical to accomplish proper vehicle servicing. An example of this is
fuel injector cleaning. Due to variation in fuel quality in different areas of the country, GM has recognized the need for fuel injector cleaning
methods on some engines, though under normal circumstances, this service is not part of the maintenance requirements.

GM has published several gasoline fuel injector cleaning bulletins that fully outline the methods to be used in conjunction with GM Part Numbered
solutions to accomplish proper and safe cleaning of the fuel injectors with preventative maintenance suggestions to maintain optimum performance.
You may refer to Corporate Bulletin Numbers 03-06-04-030 and 04-06-04-051 for additional information on this subject.

Subsystem Flushing

Flushing of A/C lines, radiators, transmission coolers, and power steering systems are recognized practices to be performed after catastrophic
failures or extreme corrosion when encountered in radiators. For acceptable A/C flushing concerns, refer to Corporate Bulletin Number
01-01-38-006. This practice is NOT required or recommended for normal service operations.

The use of external transmission fluid exchange or flush machines is NOT recommended for the automatic or manual transmission. Use of external
machines to replace the fluid may affect the operation or durability of the transmission. Transmission fluid should only be replaced by draining and
refilling following directions in SI. Refer to Automatic/Manual Transmission Fluid and Filter Replacement.

Approved Transmission Flushing Tool (Transmission Cooler Only)


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 621
Chevrolet Venture V6-3.4L VIN E 2946

The Automatic Transmission Oil Cooler Flush and Flow Test Tool is recommended for GM vehicles. Refer to Transmission Fluid Cooler Flushing
and Flow Test in SI using the J 45096.

Service Is Important to You and Your Customer

General Motors takes great pride in offering our dealerships and customers high quality vehicles that require extremely low maintenance over the
life of the vehicle. This low cost of ownership builds repeat sales and offers our customers measurable economy of operation against competing
vehicles. Providing responsible services at the proper intervals will greatly aid your dealership with repeat business, and additional services when
required. Most customers appreciate and gain trust in the dealership that informs and offers them just what they need for continued trouble-free
operation. Examine your service department's practices and verify that all Service Consultants and Technicians focus on customer satisfaction,
vehicle inspections, and other products at time of service. Use this opportunity to upgrade the services you provide to your customers. Here are a
few suggestions:

- Take the time required to align your dealership service practices with the new GM Simplified Maintenance Schedule. Use the new vehicle
Owner's Manual Maintenance I and II schedules to create a "mirror image" in your advertising and dealer service pricing that is easily
understandable to your customer. Taking advantage of this new service strategy may greatly increase your dealership service sales and
customer retention while decreasing the frequency of visits and inconvenience to your customer.
- Review your program to ensure that all vehicles coming in are evaluated for safety and wear items. Examine all vehicles for tire condition,
signs of misalignment, brake wear, exterior lamp functionality, exhaust condition, A/C cooling performance, SRS or Air Bag MIL, along
with Service Engine Soon or Check Engine indicators. If the Service Engine Soon or Check Engine MIL is illuminated, it is vital that
you inform the customer of the concerns with ignoring the indicator and what the required repair would cost. In addition to the
possibility of increased emissions and driveability concerns, many customers are unaware that lower gas mileage may also result,
with additional cost to the customer.
- Be complete in your service recommendations. Some sales opportunities are not being fully pursued nationally. Focus on overlooked but
required maintenance that has real benefits to the customer. Many vehicles are equipped with cabin air filters. If these filters are used beyond
replacement time, they may impede airflow decreasing A/C and heating performance. Make sure these filters are part of your recommended
service. Note that some of our vehicles may not have been factory equipped but will accept the filters as an accessory.
- Express the value in maintaining the finish quality of the customer's vehicle at the Maintenance I and II visits. More fully utilize the vehicle
prep personnel you already have in place. In today's world, many people simply ignore the finish of their vehicle, at best infrequently using
an automatic car wash for exterior cleaning. Offer vehicle detailing services in stages from just a wash and wax to a complete interior
cleaning. When paired with the Simplified Maintenance visit, this will increase customer satisfaction. On return, the customer gets a visibly
improved vehicle that will be a source of pride of ownership along with a vehicle that is now fully maintained. Also, reinforce the improved
resale value of a completely maintained vehicle.
- For customers who clean and maintain the appearance of their vehicles themselves encourage the use of GM Vehicle Care products. Many
customers may have never used GM Car Wash/Wax Concentrate, GM Cleaner Wax or a longtime product, GM Glass Cleaner, which is a
favorite of many customers who try it just once. If your dealership give samples of these products with new car purchases, customers may
already be sold on the product but not willing to make a special trip to the dealership. Capitalize on sales at this time. Stock shelves right at
the Service counter with these products and consider instituting compensation programs for Service Consultants who suggest these products.
Many consumers faced with an intimidating wall full of car care products sold at local auto parts stores may find it comforting to purchase a
fully tested product sold by GM that they know will not harm the finish of their vehicle. We suggest these competitively priced basic vehicle
care products to emphasize:

In USA:
- #12378401 GM Vehicle Care Wash/Wax Concentrate 16 fl. oz. (0.473L)
- #89021822 GM Vehicle Care Glass Cleaner Aerosol 18 oz. (510 g)
- #12377966 GM Vehicle Care Cleaner Wax 16 fl. oz. (0.473L)
- #1052929 GM Vehicle Care Chrome and Wire Wheel Cleaner 16 fl. oz. (0.473L)
- #88861431 GM Vehicle Care Odor Eliminator 24 fl. oz. (0.710L)

In Canada:
- #10953203 GM Vehicle Care Wash & Wax Concentrate 473 mL
- #992727 GM Glass Cleaner Aerosol 500 g
- #10952905 GM Vehicle Care Liquid Cleaner/Wax 473 mL
- #10953013 GM Vehicle Care Chrome Cleaner and Polish 454 mL
- #10953202 GM Vehicle Care Wheel Brite 473 mL
- #88901678 GM Vehicle Care Odor Eliminator 473 mL

- Display signboards with the installed price for popular GM Accessories such as running boards and Tonneau Covers. Customers may not
think to ask about these desirable items at the time of a service visit.
- Finally, take advantage of the GM Goodwrench initiatives (Tire Program, Goodwrench Credit Card, etc. / Dealer Marketing Association
(DMA) Promotions in Canada) to provide the customer with more reasons to identify your dealership as the best place to go for parts and
service.

Remember to utilize ALL of the service aspects you possess in your dealership to satisfy and provide value to your customer. Many businesses
exist profitably as an oil change location, a vehicle repair facility, or a detailing shop alone. You already have the capabilities of all three and
provide these services with the inherent trust of your customer, under the GM Mark of Excellence.
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 622
Chevrolet Venture V6-3.4L VIN E 2947

Disclaimer

Technical Service Bulletin # 00-06-01-026C Date: 100203

Engine - Intake Manifold Inspection/Replacement


INFORMATION

Bulletin No.: 00-06-01-026C

Date: February 03, 2010

Subject: Intake Manifold Inspection/Replacement After Severe Internal Engine Damage

Models:

2010 and Prior Passenger Cars and Trucks (Including Saturn)


2010 and Prior HUMMER H2, H3
2009 and Prior Saab 9-7X

Supercede:
This bulletin is being revised to include additional model years. Please discard Corporate Bulletin Number 00-06-01-026B (Section 06 - Engine).

When replacing an engine due to internal damage, extreme care should be taken when transferring the intake manifold to the new Goodwrench
service engine long block. Internal damage may result in the potential discharge of internal engine component debris in the intake manifold via
broken pistons and/or bent, broken, or missing intake valves. After removing the intake manifold from the engine, the technician should carefully
inspect all of the cylinder head intake ports to see if the valve heads are still present and not bent. Usually when the valve heads are missing or
sufficiently bent, internal engine component debris will be present to varying degrees in the intake port of the cylinder head. If this debris is present
in any of the cylinder head intake ports, the intake manifold should be replaced. This replacement is required due to the complex inlet runner and
plenum configuration of most of the intake manifolds, making thorough and complete component cleaning difficult and nearly impossible to verify
complete removal of debris. Re-installation of an intake manifold removed from an engine with deposits of internal engine component debris may
result in the ingestion of any remaining debris into the new Goodwrench service engine. This may cause damage or potential failure of the new
service engine.

Disclaimer

Technical Service Bulletin # 00-03-10-002E Date: 100315

Wheels - Chrome Wheel Staining/Pitting/Corrosion


INFORMATION

Bulletin No.: 00-03-10-002E

Date: March 15, 2010

Subject: Chemical Staining, Pitting, Corrosion and/or Spotted Appearance of Chromed Aluminum Wheels

Models:

2010 and Prior GM Cars and Trucks (Including Saturn and Saab)
2003-2009 HUMMER H2
2006-2010 HUMMER H3

Supercede:
This bulletin is being revised to add models and model years. Please discard Corporate Bulletin Number 00-03-10-002D (Section 03 - Suspension).
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 623
Chevrolet Venture V6-3.4L VIN E 2948

Important
You may give a copy of this bulletin to the customer.

What is Chemical Staining of Chrome Wheels?


Figure 1

Chemical staining in most cases results from acid based cleaners (refer to Figure 1 for an example). These stains are frequently milky or greenish in
appearance. They result from using cleaning solutions that contain hydrofluoric, oxalic and most other acids on chrome wheels (or any wheels).
Soap and water is usually sufficient to clean chrome wheels, but if a cleaner must be used on chrome wheels, GM Chrome and Wire Wheel
Cleaner, P/N 1052929 (in Canada, use P/N 10953202), or equivalent, is recommended. Do not use cleaning solutions that contain hydrofluoric,
oxalic and most other acids on chrome wheels (or any wheels).

Notice

Many wheel cleaner instructions advise to take care to avoid contact with painted surfaces. Most customers think of painted surfaces as the fenders,
quarter panels and other exterior sheet metal. Many vehicles have painted brake calipers. Acidic wheel cleaners may craze, crack, or discolor the
paint on the brake calipers. Damage from wheel cleaners is not covered under the vehicle new car warranty. Soap and water applied with a soft
brush is usually all that is required to clean the calipers.

Important
GM Chrome and Wire Wheel cleaner, P/N 1052929 (in Canada, P/N 10953202), has a mild phosphoric acid, which will not stain the
chrome. However, do not use this product on clear-coated aluminum wheels.

Whenever any wheel cleaner is used, it must be THOROUGHLY rinsed off of the wheel with clean, clear water. Special care must be taken to rinse
under the hub cap, balance weights, wheel nuts, lug nut caps, between the wheel cladding and off the back side of the wheel.

Notice

Do not use cleaning solutions that contain hydrofluoric, oxalic and most other acids on chrome wheels (or any wheels).

If the customer is unsure of the chemical make-up of a particular wheel cleaner, it should be avoided.

For wheels showing signs of milky staining from acidic cleaners, refer to Customer Assistance and Instructions below.

Warranty of Stained Chrome Wheels

Stained wheels are not warrantable. Most acid based cleaners will permanently stain chrome wheels. Follow-up with dealers has confirmed that
such cleaners were used on wheels that were returned to the Warranty Parts Center (WPC). Any stained wheels received by the WPC will be
charged back to the dealership. To assist the customer, refer to Customer Assistance and Instructions below.

Pitting or Spotted Appearance of Chrome Wheels


Figure 2
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 624
Chevrolet Venture V6-3.4L VIN E 2949

A second type or staining or finish disturbance may result from road chemicals, such as calcium chloride used for dust control of unpaved roads.
The staining will look like small pitting (refer to Figure 2). This staining will usually be on the leading edges of each wheel spoke, but may be
uniformly distributed. If a vehicle must be operated under such conditions, the chrome wheels should be washed with mild soap and water and
thoroughly rinsed as soon as conveniently possible.

Important
Road chemicals, such as calcium chloride used for dust control of unpaved roads, can also stain chrome wheels. The staining will look like
small pitting. This staining will usually be on the leading edges of each wheel spoke. This is explained by the vehicle traveling in the
forward direction while being splashed by the road chemical. If a vehicle must be operated under such conditions, the chrome wheels
should be washed with mild soap and water and thoroughly rinsed as soon as conveniently possible.

Warranty of Pitted or Spotted Chrome Wheels

Wheels returned with pitting or spotting as a result of road chemicals may be replaced one time. Damage resulting from contact with these applied
road chemicals is corrosive to the wheels finish and may cause damage if the wheels are not kept clean.

Important
Notify the customer that this is a one time replacement. Please stress to the customer the vital importance of keeping the wheels clean if
they are operating the vehicle in an area that applies calcium chloride or other dust controlling chemicals! "GM of Canada" dealers
require prior Warranty Manager approval.

Customer Assistance and Instructions

GM has looked for ways customers may improve the appearance of wheels damaged by acidic cleaners. The following product and procedure has
been found to dramatically improve the appearance of stained wheels. For wheels that have milky stains caused by acidic cleaners try the following:

Notice

THE 3M CHROME AND METAL POLISH REQUIRED FOR THIS PROCEDURE IS AN EXTREMELY AGGRESSIVE POLISH/CLEANER.
THE WHEELS MUST BE CLEANED BEFORE APPLICATION TO AVOID SCRATCHING THE WHEEL SURFACE. THIS PRODUCT
WILL REDUCE THE THICKNESS OF THE CHROME PLATING ON THE WHEEL AND IF USED INCORRECTLY OR EXCESSIVELY
MAY REMOVE THE CHROME PLATING ALL TOGETHER, EXPOSING A LESS BRIGHT AND BRASSY COLORED SUB-LAYER.
FOLLOW INSTRUCTIONS EXACTLY.

1. Wash the wheels with GM Chrome and Wire Wheel Cleaner, P/N 1052929 (in Canada, use P/N 10953202). Follow the instructions as
indicated on the bottle for stubborn stains. This step will clean and may reduce wheel staining. Flood all areas of the wheel with water to
rinse.
2. Dry the wheels completely.

Notice
Begin with a small section of the wheel and with light pressure buff off polish and examine results. ONLY apply and rub with sufficient
force and time to remove enough staining that you are satisfied with the results. Some wheels may be stained to the extent that you may only
achieve a 50% improvement while others may be able to be restored to the original lustre. IN ALL CASES, only apply until the results are
satisfactory.

3. Apply 3M Chrome and Metal Polish #39527* with a clean terry cloth towel. As you apply the polish, the staining will be diminished.
4. When dry, buff off the polish with a clean portion of the towel.
5. Repeat application of the 3M Chrome and Metal Polish until satisfied with the results. If continued applications fail to improve the
appearance further discontinue use.

This procedure will improve the appearance of the wheels and may, with repeated applications, restore the finish dramatically. For wheels that
exhibit spotting from road chemicals the above procedure may marginally improve the condition but will not restore the finish or remove the
pitting. In this type of staining the wheel finish has actually been removed in spots and no manner of cleaning will restore the finish.

*We believe this source and their products to be reliable. There may be additional manufacturers of such products/materials. General Motors does
not endorse, indicate any preference for or assume any responsibility for the products or material from this firm or for any such items that may be
available from other sources.
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 625
Chevrolet Venture V6-3.4L VIN E 2950

Parts Information

*This product is currently available from 3M. To obtain information for your local retail location please call 3M at 1-888-364-3577.

Disclaimer

Technical Service Bulletin # 05-03-10-003F Date: 100427

Tires/Wheels - Low Tire/Leaking Cast Aluminum Wheels


TECHNICAL

Bulletin No.: 05-03-10-003F

Date: April 27, 2010

Subject: Low Tire Pressure, Leaking Cast Aluminum Wheels (Repair with Adhesive Sealant)

Models:

2011 and Prior GM Passenger Cars and Light Duty Trucks (Including Saturn)
2010 and Prior HUMMER H2, H3
2009 and Prior Saab 9-7X
with Cast Aluminum Wheels

Supercede:
This bulletin is being revised to update the model years and the bulletin reference information. Please discard Corporate Bulletin Number
05-03-10-003E (Section 03 - Suspension).

Condition

Some customers may comment on a low tire pressure condition.

Diagnosis of the low tire pressure condition indicates an air leak through the cast aluminum wheel.

Cause

Porosity in the cast aluminum wheel may be the cause.

Notice

This bulletin specifically addresses issues related to the wheel casting that may result in an air leak. For issues related to corrosion of the wheel in
service, please refer to Corporate Bulletin Number 08-03-10-006C - Tire Slowly Goes Flat, Tire Air Loss, Low Tire Pressure Warning Light
Illuminated, Aluminum Wheel Bead Seat Corrosion (Clean and Resurface Wheel Bead Seat).

Correction

1. Remove the tire and wheel assembly from the vehicle. Refer to the appropriate service procedure in SI.
2. Locate the leaking area by inflating the tire to 276 kPa (40 psi) and dipping the tire/wheel assembly in a water bath, or use a spray bottle with
soap and water to locate the specific leak location.

Important

- If the porosity leak is located in the bead area of the aluminum rim (where the tire meets the rim), the wheel should be replaced.
- If two or more leaks are located on one wheel, the wheel should be replaced.
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 626
Chevrolet Venture V6-3.4L VIN E 2951

3. If air bubbles are observed, mark the location.

- If the leak location is on the tire/rubber area, refer to Corporate Bulletin Number 04-03-10-001F - Tire Puncture Repair Procedures for
All Cars and Light Duty Trucks.
- If the leak is located on the aluminum wheel area, continue with the next step.

4. Inscribe a mark on the tire at the valve stem in order to indicate the orientation of the tire to the wheel.
5. Dismount the tire from the wheel. Refer to Tire Mounting and Dismounting.
6. Remove the tire pressure sensor. Refer to Tire Pressure Sensor removal procedure in SI.
7. Scuff the INSIDE rim surface at the leak area with #80 grit paper and clean the area with general purpose cleaner, such as 3M(R) General
Purpose Adhesive Cleaner, P/N 08984, or equivalent.
8. Apply a 3 mm (0.12 in) thick layer of Silicone - Adhesive/Sealant, P/N 12378478 (in Canada, use 88900041), or equivalent, to the leak area.
9. Allow for the adhesive/sealant to dry.

Notice
Caution must be used when mounting the tire so as not to damage the sealer. Damaging the repair area may result in an air leak.

10. Align the inscribed mark on the tire with the valve stem on the wheel.
11. Reinstall the Tire Pressure Sensor. Refer to Tire Pressure Sensor installation procedure in SI.
12. Mount the tire on the wheel. Refer to Tire Mounting and Dismounting.
13. Pressurize the tire to 276 kPa (40 psi) and inspect for leaks.
14. Adjust tire pressure to meet the placard specification.
15. Balance the tire/wheel assembly. Refer to Tire and Wheel Assembly Balancing - Off-Vehicle.
16. Install the tire and wheel assembly onto the vehicle. Refer to the appropriate service procedure in SI.

Parts Information

Warranty Information (excluding Saab U.S. Models)

Important
The Silicone - Adhesive/Sealant comes in a case quantity of six. ONLY charge warranty one tube of adhesive/sealant per wheel repair.

For vehicles repaired under warranty, use:

One leak repair per wheel.

Warranty Information (Saab U.S. Models)

For vehicles repaired under warranty, use the table above.


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 627
Chevrolet Venture V6-3.4L VIN E 2952

Disclaimer

Technical Service Bulletin # 08-03-10-006C Date: 100427

Tires/Wheels - Tire Slowly Goes Flat/Warning Light ON


TECHNICAL

Bulletin No.: 08-03-10-006C

Date: April 27, 2010

Subject: Tire Slowly Goes Flat, Tire Air Loss, Low Tire Pressure Warning Light Illuminated, Aluminum Wheel Bead Seat Corrosion (Clean and
Resurface Wheel Bead Seat)

Models:

2000-2011 GM Passenger Cars and Light Duty Trucks (including Saturn)


2003-2009 HUMMER H2
2006-2010 HUMMER H3
2005-2009 Saab 9-7X

Supercede:
This bulletin is being revised to update the model years. Please discard Corporate Bulletin Number 08-03-10-006B (Section 03 - Suspension).

Condition

Some customers may comment on a tire that slowly loses air pressure over a period of days or weeks.

Cause

Abrasive elements in the environment may intrude between the tire and wheel at the bead seat. There is always some relative motion between the
tire and wheel (when the vehicle is driven) and this motion may cause the abrasive particles to wear the wheel and tire materials. As the wear
continues, there may also be intrusion at the tire/wheel interface by corrosive media from the environment. Eventually a path for air develops and a
'slow' leak may ensue. This corrosion may appear on the inboard or outboard bead seating surface of the wheel. This corrosion will not be visible
until the tire is dismounted from the wheel.

Notice

This bulletin specifically addresses issues related to wheel bead seat corrosion that may result in an air leak. For issues related to porosity of the
wheel casting that may result in an air leak, please refer to Corporate Bulletin Number 05-03-10-006F - Low Tire Pressure, Leaking Cast
Aluminum Wheels (Repair with Adhesive Sealant)

Correction

In most cases, this type of air loss can be corrected by following the procedure below.

Important
DO NOT replace a wheel for slow air loss unless you have evaluated and/or tried to repair the wheel with the procedure below.

Notice

The repair is no longer advised or applicable for chromed aluminum wheels.


1. Remove the wheel and tire assembly for diagnosis. Refer to Tire and Wheel Removal and Installation in SI.
2. After a water dunk tank leak test, if you determine the source of the air leak to be around the bead seat of the wheel, dismount the tire to
examine the bead seat. Shown below is a typical area of bead seat corrosion.Typical Location of Bead Seat Corrosion
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 628
Chevrolet Venture V6-3.4L VIN E 2953

Important
Other forms of slow air leaks are possible. If the body of the tire, valve stem and wheel flange show no signs of air seepage, refer to
Corporate Bulletin Number 05-03-10-003D for additional information on possible wheel porosity issues.

3. Bead seat corrosion is identified by what appears like blistering of the wheel finish, causing a rough or uneven surface that is difficult for the
tire to maintain a proper seal on. Below is a close-up photo of bead seat corrosion on an aluminum wheel that was sufficient to cause slow air
loss. Close-Up of Bead Seat Corrosion

4. If corrosion is found on the wheel bead seat, measure the affected area as shown below.

- For vehicles with 32,186 km (20,000 mi) or less, the total allowable combined linear area of repairable corrosion is 100 mm (4 in) or less.
If the total area(s) of corrosion exceed these dimensions, the wheel should be replaced.
- For vehicles that have exceeded 32,186 km (20,000 mi), the total allowable combined linear area of repairable corrosion is 200 mm (8 in)
or less. If the total area(s) of corrosion exceed these dimensions, the wheel should be replaced.

5. In order to correct the wheel leak, use a clean-up (fine cut) sanding disc or biscuit to remove the corrosion and any flaking paint. You should
remove the corrosion back far enough until you reach material that is stable and firmly bonded to the wheel. Try to taper the edge of any
flaking paint as best you can in order to avoid sharp edges that may increase the chance of a leak reoccurring. The photo below shows an
acceptable repaired surface.

Notice
Corrosion that extends up the lip of the wheel, where after the clean-up process it would be visible with the tire mounted, is only acceptable
on the inboard flange. The inboard flange is not visible with the wheel assembly in the mounted position. If any loose coatings or corrosion
extend to the visible surfaces on the FACE of the wheel, that wheel must be replaced.

Important
Remove ONLY the material required to eliminate the corrosion from the bead seating surface. DO NOT remove excessive amounts
of material. ALWAYS keep the sealing surface as smooth and level as possible.

Acceptably Prepared (Cleaned-Up) Wheel Surface


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 629
Chevrolet Venture V6-3.4L VIN E 2954

6. Once the corrosion has been eliminated, you should coat the repaired area with a commercially available tire sealant such as Patch Brand
Bead Sealant or equivalent. Commercially available bead sealants are black rubber-like coatings that will permanently fill and seal the
resurfaced bead seat. At 21°C (70°F) ambient temperature, this sealant will set-up sufficiently for tire mounting in about 10 minutes.Coated
and Sealed Bead Seat

7. Remount the tire and install the repaired wheel and tire assembly. Refer to Tire and Wheel Removal and Installation in SI.

Parts Information

Patch Brand Bead Sealer is available from Myers Tires at 1-800-998-9897 or on the web at www.myerstiresupply.com. The one-quart size can of
sealer will repair about 20 wheels.

Warranty Information (excluding Saab U.S. Models)

For vehicles repaired under warranty, use:

Warranty Information (Saab U.S. Models)

For vehicles repaired under warranty, use the table above.

Disclaimer

Technical Service Bulletin # 04-03-10-001F Date: 100427


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 630
Chevrolet Venture V6-3.4L VIN E 2955

Tires/Wheels - Tire Puncture Repair Procedures


INFORMATION

Bulletin No.: 04-03-10-001F

Date: April 27, 2010

Subject: Tire Puncture Repair Procedures For All Cars and Light Duty Trucks

Models:

2011 and Prior GM Passenger Cars and Light Duty Trucks (including Saturn)
2010 and Prior HUMMER H2, H3
2009 and Prior Saab 9-7X

Supercede:
This bulletin is being revised to add model years. Please discard Corporate Bulletin Number 04-03-10-001E (Section 03 - Suspension).

This bulletin covers puncture repair procedures for passenger car and light duty truck radial tires in the tread area only. The tire manufacturer must
be contacted for its individual repair policy and whether or not the speed rating is retained after repair.

Caution

- Tire changing can be dangerous and should be done by trained professionals using proper tools and procedures. Always read and understand
any manufacturer's warnings contained in their customers literature or molded into the tire sidewall.
- Serious eye and ear injury may result from not wearing adequate eye and ear protection while repairing tires.
- NEVER inflate beyond 275 kPa (40 pounds) pressure to seat beads.

Some run flat tires, such as the Goodyear Extended Mobility Tire (EMT) used on the Corvette, may require more than 275 kPa (40 psi) to
seat the bead. In such a case, a tire safety cage must be used. Consult the tire manufacturer for its individual repair policy.
- NEVER stand, lean or reach over the assembly during inflation.

Repairable area on a radial tire.

Important

- NEVER repair tires worn to the tread indicators 1.59 mm (2/32") remaining depth).
- NEVER repair tires with a tread puncture larger than 6.35 mm (1/4").
- NEVER substitute an inner tube for a permissible or non-permissible repair.
- NEVER perform an outside-in tire repair (plug only, on the wheel).
- Every tire must be removed from the wheel for proper inspection and repair.
- Regardless of the type of repair used, the repair must seal the inner liner and fill the injury.
- Consult with repair material supplier/manufacturer for repair unit application procedures and repair tools/repair material
recommendations.

Three basic steps for tire puncture repair:


1. Remove the tire from the wheel for inspection and repair.
2. Fill the injury (puncture) to keep moisture out.
3. Seal the inner liner with a repair unit to prevent air loss.

External Inspection
1. Prior to demounting, inspect the tire surface, the valve and the wheel for the source of the leak by using a water and soap solution. Mark the
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 631
Chevrolet Venture V6-3.4L VIN E 2956
injured area and totally deflate the tire by removing the valve core.
2. Demount the tire from the wheel and place the tire on a well-lighted spreader.

Internal Inspection

1. Spread the beads and mark the puncture with a tire crayon.
2. Inspect the inner tire for any signs of internal damage.
3. Remove the puncturing object, noting the direction of the penetration.
4. Probe the injury with a blunt awl in order to determine the extent and direction of the injury.
5. Remove any loose foreign material from the injury.
6. Punctures exceeding 6.35 mm (1/4") should not be repaired.

Cleaning

1. Clean the area around the puncture thoroughly with a proper liner cleaner, clean cloth and a scraper. This step serves to remove dirt and mold
lubricants to insure proper adhesion and non-contamination of the buffing tool.
2. Refer to information on the product or manufacturer's Material Safety Data Sheet and follow guidelines for handling and disposal.

Clean the Injury Channel


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 632
Chevrolet Venture V6-3.4L VIN E 2957

1. Use a proper hand reamer, carbide cutter or drill bit to ream the puncture channel from the inside of the tire in order to clean the injury.
2. Remove steel wires protruding above the liner surface to prevent damage to the repair unit.
3. Consult your repair material supplier for recommended reaming tool(s).

Fill the Injury

1. It is necessary to fill the injury channel to provide back up for the repair unit and to prevent moisture from entering the tire fabric and steel
wires.
2. (For combination repair/plug units skip this step.) Cement the injured channel and fill the injury from the inside of the tire with the repair
plug per repair material manufacturer's recommendations. Without stretching the plug, cut the plug off just above the inside tire surface.
3. Consult your repair material supplier for proper repair material selection.

Repair Unit Selection

Important
Do not install the repair unit in this step.

1. Center the repair unit over the injury as a reference and outline an area larger than the unit so that buffing will not remove the crayon marks.
2. Remove the repair unit.
3. DO NOT overlap previous or multiple repair units.
4. Consult your repair material supplier for proper repair unit selection.

Buffing
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 633
Chevrolet Venture V6-3.4L VIN E 2958

1. To prevent contamination and preserve the outline, buff within the marked area thoroughly and evenly with a low speed buffing tool using a
fine wire brush or gritted rasp.
2. Buff to a smooth velvet surface (RMA #1 or #2 buffed texture).
3. Use caution not to gouge the inner liner or expose casing fabric.
4. Remove any buffing dust with a vacuum cleaner.
5. Consult your repair material supplier for a proper buffing tool.

Cementing

Apply chemical cement according to the repair material manufacturer's procedures.

Repair Unit Application

1. The tire must be in the relaxed position when the repair unit is installed (Do not spread the beads excessively).

Two-Piece Plug and Repair Units


1. If applicable, install the repair unit so that the alignment is correct.
2. Center the repair unit over the injury and stitch down thoroughly with the stitching tool, working from the center out.
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 634
Chevrolet Venture V6-3.4L VIN E 2959

3. Being careful not to stretch the plug material, cut the plug flush with the outer tread.

Combination Repair/Plug Units


1. Pull the plug through the injury until the repair just reaches the liner. Stitch down thoroughly.
2. Follow the repair material manufacturer's recommendations for further installation instructions.

2. Consult your repair material supplier for the proper stitching tool.

Safety Cage

Some run flat tires, such as the Goodyear Extended Mobility Tire (EMT) used on the Corvette, may require more than 275 kPa (40 psi) to seat the
bead. In such a case, a tire safety cage must be used. Consult the tire manufacturer for its individual repair policy.

Final Inspection

1. After remounting and inflating the tire, check both beads, the repair and the valve with a water and soap solution in order to detect leaks.
2. If the tire continues to lose air, the tire must be demounted and reinspected.
3. Balance the tire and wheel assembly. Refer to Tire and Wheel Assembly Balancing - OFF Vehicle.

For additional tire puncture repair information, contact:


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 635
Chevrolet Venture V6-3.4L VIN E 2960

Rubber Manufacturers Association (RMA)

DisclaimerTechnical Service Bulletin # 05-03-10-020C Date: 100427

Wheels/Tires - Use of Nitrogen Gas in Tires


INFORMATION

Bulletin No.: 05-03-10-020C

Date: April 27, 2010

Subject: Use of Nitrogen Gas in Tires

Models:

2011 and Prior GM Passenger Cars and Trucks (including Saturn)


2010 and Prior HUMMER H2, H3
2009 and Prior Saab 9-7X

Supercede:
This bulletin is being revised to add model years. Please discard Corporate Bulletin Number 05-03-10-020B (Section 03 - Suspension).

GM's Position on the Use of Nitrogen Gas in Tires

General Motors does not oppose the use of purified nitrogen as an inflation gas for tires. We expect the theoretical benefits to be reduced in
practical use due to the lack of an existing infrastructure to continuously facilitate inflating tires with nearly pure nitrogen. Even occasional inflation
with compressed atmospheric air will negate many of the theoretical benefits. Given those theoretical benefits, practical limitations, and the robust
design of GM original equipment TPC tires, the realized benefits to our customer of inflating their tires with purified nitrogen are expected to be
minimal.

The Promise of Nitrogen: Under Controlled Conditions

Recently, nitrogen gas (for use in inflating tires) has become available to the general consumer through some retailers. The use of nitrogen gas to
inflate tires is a technology used in automobile racing. The following benefits under controlled conditions are attributed to nitrogen gas and its
unique properties:

- A reduction in the expected loss of Tire Pressure over time.


- A reduction in the variance of Tire Pressures with temperature changes due to reduction of water vapor concentration.
- A reduction of long term rubber degradation due to a decrease in oxygen concentrations.

Important
These are obtainable performance improvements when relatively pure nitrogen gas is used to inflate tires under controlled
conditions.

The Promise of Nitrogen: Real World Use

Nitrogen inflation can provide some benefit by reducing gas migration (pressure loss) at the molecular level through the tire structure. NHTSA
(National Highway Traffic Safety Administration) has stated that the inflation pressure loss of tires can be up to 5% a month. Nitrogen molecules
are larger than oxygen molecules and, therefore, are less prone to "seeping" through the tire casing. The actual obtainable benefits of nitrogen vary,
based on the physical construction and the materials used in the manufacturing of the tire being inflated.

Another potential benefit of nitrogen is the reduced oxidation of tire components. Research has demonstrated that oxygen consumed in the
oxidation process of the tire primarily comes from the inflation media. Therefore, it is reasonable to assume that oxidation of tire components can
be reduced if the tire is inflated with pure nitrogen. However, only very small amounts of oxygen are required to begin the normal oxidation
process. Even slight contamination of the tire inflation gas with compressed atmospheric air during normal inflation pressure maintenance, may
negate the benefits of using nitrogen.

GM Tire Quality, Technology and Focus of Importance

Since 1972, General Motors has designed tires under the TPC (Tire Performance Criteria) specification system, which includes specific
requirements that ensure robust tire performance under normal usage. General Motors works with tire suppliers to design and manufacture original
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 636
Chevrolet Venture V6-3.4L VIN E 2961
equipment tires for GM vehicles. The GM TPC addresses required performance with respect to both inflation pressure retention, and endurance
properties for original equipment tires. The inflation pressure retention requirements address availability of oxygen and oxidation concerns, while
endurance requirements ensure the mechanical structure of the tire has sufficient strength. This combination has provided our customers with tires
that maintain their structural integrity throughout their useful treadlife under normal operating conditions.

Regardless of the inflation media for tires (atmospheric air or nitrogen), inflation pressure maintenance of tires is critical for overall tire, and
ultimately, vehicle performance. Maintaining the correct inflation pressure allows the tire to perform as intended by the vehicle manufacturer in
many areas, including comfort, fuel economy, stopping distance, cornering, traction, treadwear, and noise. Since the load carrying capability of a
tire is related to inflation pressure, proper inflation pressure maintenance is necessary for the tire to support the load imposed by the vehicle without
excessive structural degradation.

Important
Regardless of the inflation media for tires (atmospheric air or nitrogen), inflation pressure maintenance of tires is critical for overall tire,
and ultimately, vehicle performance.

Disclaimer

Technical Service Bulletin # 10-08-50-003 Date: 100308

Restraints - Driver/Passenger Seat Head Rest Information


INFORMATION

Bulletin No.: 10-08-50-003

Date: March 08, 2010

Subject: Information on Driver or Passenger Seat Head Restraint Concerns with Comfort, Custom Upholstery or Other Comfort Enhancing
Devices

Models:

2010 and Prior GM Passenger Cars and Trucks (including Saturn)


2010 and Prior HUMMER H2, H3
2009 and Prior Saab 9-7X
Equipped With Adjustable Head Restraints

Important
ON A GM VEHICLE EQUIPPED WITH ADJUSTABLE HEAD RESTRAINTS, USE THE HEAD RESTRAINT COVERS, FOAM AND
OTHER SEAT-RELATED EQUIPMENT AS RELEASED BY GM FOR THAT VEHICLE. DO NOT ALTER OR REPOSITION THE
HEAD RESTRAINT SYSTEM. ANY ALTERATIONS TO HEAD RESTRAINTS DEFEATS THE INTENDED DESIGN OF THE
SYSTEM. GM WILL NOT BE LIABLE FOR ANY PROBLEMS CAUSED BY USE OF SUCH IMPROPER DESIGN ALTERATIONS,
INCLUDING ANY WARRANTY REPAIRS INCURRED.

You may have a customer with a concern that the head restraint is uncomfortable or sits too far forward. The front driver and passenger seats are
equipped with head restraints that have been designed to help minimize injuries while still providing comfort to the occupants. Each GM vehicle
has its own specifically designed head restraint. The head restraints should only be used in the vehicle for which they were designed. The head
restraint will not operate to its design intent if the original foam is replaced (1) by non-GM foam or head restraint, (2) by GM foam or head restraint
designed for a different vehicle, (3) by GM foam or head restraint that has been altered by a trim shop or (4) if any object, such as an aftermarket
comfort enhancing pad or device, is installed.

Never modify the design of the head restraint or remove the head restraint from the vehicle as this may interfere with the operation of the seating
and restraint systems and may prevent proper positioning of the passenger within the vehicle.

Disclaimer
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 637
Chevrolet Venture V6-3.4L VIN E 2962

Technical Service Bulletin # 08-08-42-005B Date: 090618

Lighting - Headlamp Warranty Replacement Guideline


INFORMATION

Bulletin No.: 08-08-42-005B

Date: June 11, 2009

Subject: Replacement of Headlamp Assemblies Under Warranty and Use of GM vs. Non-GM Headlamp Assemblies

Models:
2010 and Prior GM Passenger Cars and Trucks (Including Saturn and Saab)
2010 and Prior HUMMER H2, H3

Supercede:

This bulletin is being revised to update parts identification and model years. Please discard Corporate Bulletin Number 08-08-42-005A (Section 08
- Body and Accessories).

This bulletin is being issued to inform dealers that whenever a headlamp replacement under warranty is necessary, be sure to use the correct
General Motors (GM) approved headlamp assembly.

Recent Warranty Parts Center reviews of headlamps replaced in the field show that some dealers have returned non-GM (counterfeit) headlamp
assemblies under warranty.

These non-GM headlamp assemblies (referred to as "knock-offs") are not made to GM specifications. Also, the appearance of these headlamp
assemblies are very close to the genuine parts. Refer to the figures below.

The figure above shows a non-GM or "knockoff" headlamp assembly. The lens stamping will read "EAGLE EYES." There are other companies
that manufacture replacement lamps that can be installed on a variety of GM vehicles.

These non-GM headlamp assemblies will not be honored under warranty. These are not original equipment and are not sanctioned as replacement
parts by GM.

DisclaimerTechnical Service Bulletin # 06-08-50-009E Date: 100225

Restraints - Passenger Presence System Information


INFORMATION

Bulletin No.: 06-08-50-009E

Date: February 24, 2010

Subject: Information on Passenger Presence Sensing System (PPS or PSS) Concerns With Custom Upholstery, Accessory Seat Heaters or Other
Comfort Enhancing Devices
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 638
Chevrolet Venture V6-3.4L VIN E 2963

Models:

2010 and Prior GM Passenger Cars and Trucks (including Saturn)


2010 and Prior HUMMER H2, H3
2009 and Prior Saab 9-7X
Equipped With Passenger Presence Sensing System

Supercede:
This bulletin is being revised to update the model years and to add an Important statement. Please discard Corporate Bulletin Number
06-08-50-009D (Section 08 - Body and Accessories).

Concerns About Safety and Alterations to the Front Passenger Seat

Important
ON A GM VEHICLE EQUIPPED WITH A PASSENGER SENSING SYSTEM, USE THE SEAT COVERS AND OTHER
SEAT-RELATED EQUIPMENT AS RELEASED BY GM FOR THAT VEHICLE. DO NOT ALTER THE SEAT COVERS OR
SEAT-RELATED EQUIPMENT. ANY ALTERATIONS TO SEAT COVERS OR GM ACCESSORIES DEFEATS THE INTENDED
DESIGN OF THE SYSTEM. GM WILL NOT BE LIABLE FOR ANY PROBLEMS CAUSED BY USE OF SUCH IMPROPER SEAT
ALTERATIONS, INCLUDING ANY WARRANTY REPAIRS INCURRED.

The front passenger seat in many GM vehicles is equipped with a passenger sensing system that will turn off the right front passenger's frontal
airbag under certain conditions, such as when an infant or child seat is present. In some vehicles, the passenger sensing system will also turn off the
right front passenger's seat mounted side impact airbag. For the system to function properly, sensors are used in the seat to detect the presence of a
properly-seated occupant. The passenger sensing system may not operate properly if the original seat trim is replaced (1) by non-GM covers,
upholstery or trim, or (2) by GM covers, upholstery or trim designed for a different vehicle or (3) by GM covers, upholstery or trim that has been
altered by a trim shop, or (4) if any object, such as an aftermarket seat heater or a comfort enhancing pad or device is installed under the seat fabric
or between the occupant and the seat fabric.

Aftermarket Seat Heaters, Custom Upholstery, and Comfort Enhancing Pads or Devices

Important
ON A GM VEHICLE EQUIPPED WITH A PASSENGER SENSING SYSTEM, USE ONLY SEAT COVERS AND OTHER
SEAT-RELATED EQUIPMENT RELEASED AS GM ACCESSORIES FOR THAT VEHICLE. DO NOT USE ANY OTHER TYPE OF
SEAT COVERS OR SEAT-RELATED EQUIPMENT, OR GM ACCESSORIES RELEASED FOR OTHER VEHICLE APPLICATIONS.
GM WILL NOT BE LIABLE FOR ANY PROBLEMS CAUSED BY USE OF SUCH IMPROPER SEAT ACCESSORIES, INCLUDING
ANY WARRANTY REPAIRS MADE NECESSARY BY SUCH USE.

Many types of aftermarket accessories are available to customers, upfitting shops, and dealers. Some of these devices sit on top of, or are Velcro(R)
strapped to the seat while others such as seat heaters are installed under the seat fabric. Additionally, seat covers made of leather or other materials
may have different padding thickness installed that could prevent the Passenger Sensing System from functioning properly. Never alter the vehicle
seats. Never add pads or other devices to the seat cushion, as this may interfere with the operation of the Passenger Sensing System and either
prevent proper deployment of the passenger airbag or prevent proper suppression of the passenger air bag.

Disclaimer

Technical Service Bulletin # 08-08-64-011A Date: 100226

Mirrors - Heated Mirrors, Defrosting Time


INFORMATION

Bulletin No.: 08-08-64-011A

Date: February 25, 2010

Subject: Information on Heated Electrochromatic Outside Rearview Mirror Performance

Models:

2010 and Prior GM Passenger Cars and Light Duty Trucks (including Saturn)
2009 and Prior HUMMER H2, H3
2009 and Prior Saab 9-7X
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 639
Chevrolet Venture V6-3.4L VIN E 2964

Supercede:
This bulletin is being revised to update the model years. Please discard Corporate Bulletin Number 08-08-64-011 (Section 08 - Body and
Accessories).

Defrosting Time/Performance Concern

The electrochromatic (auto-dimming) outside rearview mirror used on the driver's side of many GM vehicles is slower to defrost than the passenger
side outside rearview mirror.

This is a normal condition. The glass on the driver's side electrochromatic mirror is twice as thick as the traditional glass on the passenger side
mirror. The heating elements for the mirrors on both sides draw the same wattage, therefore the driver's side mirror will take approximately twice as
long to defrost as the passenger mirror (approximately four minutes versus two minutes). Should a customer indicate that the driver's side heated
mirror is not functioning correctly, verify it's function based upon this information prior to replacing the mirror.

DisclaimerTechnical Service Bulletin # 01-07-30-042F Date: 100205

A/T - 2-3 Upshift or 3-2 Downshift Clunk Noise


INFORMATION

Bulletin No.: 01-07-30-042F

Date: February 05, 2010

Subject: Information on 2-3 Upshift or 3-2 Downshift Clunk Noise

Models:

2010 and Prior GM Passenger Cars and Light Duty Trucks


2010 and Prior HUMMER H2, H3
2005-2009 Saab 9-7X
with 4L60-E, 4L65-E or 4L70-E Automatic Transmission (RPOs M30, M32, M70)

Supercede:
This bulletin is being revised to add the 2010 model year and 4L70E transmission. Please discard Corporate Bulletin Number 01-07-30-042E
(Section 07 - Transmission/Transaxle).

Important
For 2005 model year fullsize utilities and pickups, refer to Corporate Bulletin 05-07-30-012.

Some vehicles may exhibit a clunk noise that can be heard on a 2-3 upshift or a 3-2 downshift.

During a 2-3 upshift, the 2-4 band is released and the 3-4 clutch is applied. The timing of this shift can cause a momentary torque reversal of the
output shaft that results in a clunk noise. This same torque reversal can also occur on a 3-2 downshift when the 3-4 clutch is released and the 2-4
band applied. This condition may be worse on a 4-wheel drive vehicle due to the additional tolerances in the transfer case.

This is a normal condition. No repairs should be attempted.

Disclaimer

Technical Service Bulletin # 00-07-30-009D Date: 100224

A/T - Goodwrench Transmission Replacement


INFORMATION
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 640
Chevrolet Venture V6-3.4L VIN E 2965

Bulletin No.: 00-07-30-009D

Date: February 23, 2010

Subject: Current Model Year Goodwrench Transmission Replacement Assembly Program

Models:

1998-2009 GM Passenger Cars and Light Duty Trucks


2009 and Prior HUMMER H2, H3
2009 and Prior Saab 9-7x
All Equipped with 4L30-E, 4L60-E, 4L65-E, 4L70-E, 4L80-E, 4L85-E, 6L45, 6L50, 6L80, 6L90, 3T40, 4T40-E, 4T45-E, 4T60-E, 4T65-E,
4T80-E, 6T40, 6T45, 6T70 or 6T75 Automatic Transmission

Supercede:
This bulletin is being revised to remove the 2010 model year. Please discard Corporate Bulletin Number 00-07-30-009C (Section 07 -
Transmission/Transaxle).

There may be some confusion about the Goodwrench(R) transmission assembly program and whether a Goodwrench transmission is new or
remanufactured.

It should not be assumed that a Goodwrench transmission is a remanufactured unit.

Goodwrench transmissions for the current model year are new transmission assemblies. A new Goodwrench transmission may be identified by
inspecting the transmission stick-on label. The stick-on label will indicate "Manufactured by General Motors" and the identification tag is blue. A
remanufactured Goodwrench transmission may be identified by inspecting the transmission stick-on label. The stick-on label will indicate
"Remanufactured for General Motors" and the identification tag is black.

DisclaimerTechnical Service Bulletin # 10-08-110-001 Date: 100330

Interior - Proper Use of Floor Mats


INFORMATION

Bulletin No.: 10-08-110-001

Date: March 30, 2010

Subject: Information on Proper Use of Floor Mats

Models:

2011 and Prior GM Passenger Cars and Trucks (Including Saturn)


2003-2009 HUMMER H2
2006-2010 HUMMER H3, H3T
2005-2009 Saab 9-7X

GM's carpeted and all-weather (rubber) floor mats are especially designed for use in specific GM vehicles. Using floor mats that were not designed
for the specific vehicle or using them incorrectly may cause interference with the accelerator or brake pedal. Please review the following safety
guidelines regarding proper driver's side floor mat usage with the customer.

Warning

If a floor mat is the wrong size or is not properly installed, it can interfere with the accelerator pedal and/or brake pedal. Interference with the
pedals can cause unintended acceleration and/or increased stopping distance which can cause a crash and injury. Make sure the floor mat does not
interfere with the accelerator or brake pedal.

- Do not flip the driver's floor mat over (in an effort to keep the floor mat clean)
- Do not place anything on top of the driver's floor mat (e.g. carpet remnant, towel)
- Do not place another mat on top of the driver's floor mat (e.g. do not place all-weather rubber mats over carpeted floor mats)
- Only use floor mats that are designed specifically for your vehicle
- When using replacement mats, make certain the mats do not interfere with the accelerator or brake pedal before driving the vehicle
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 641
Chevrolet Venture V6-3.4L VIN E 2966

If your vehicle is equipped with a floor mat retaining pin(s) or clip(s), make certain the mat is installed correctly and according to the instructions.

After installing floor mats, make certain they cannot move and do not interfere with the accelerator or brake pedals.

Disclaimer
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 642
Chevrolet Venture V6-3.4L VIN E 2967

Technical Service Bulletin # 00-03-10-006F Date: 100504

Wheels/Tires - Tire Radial Force Variation (RFV)


INFORMATION

Bulletin No.: 00-03-10-006F

Date: May 04, 2010

Subject: Information on Tire Radial Force Variation (RFV)

Models:

2011 and Prior GM Passenger Cars and Light Duty Trucks


2010 and Prior HUMMER H2, H3
2009 and Prior Saab 9-7X
2000-2005 Saturn L Series
2003-2007 Saturn ION

Supercede:
This bulletin is being revised to considerably expand the available information on Radial Force Variation (RFV) and should be reviewed in whole.
Please discard Corporate Bulletin Number 00-03-10-006E (Section 03 - Suspension).

Important

- Before measuring tires on equipment such as the Hunter GSP9700, the vehicle MUST be driven a minimum of 16 km (10 mi) to
ensure removal of any flat-spotting. Refer to Corporate Bulletin Number 03-03-10-007E - Tire/Wheel Characteristics of GM
Original Equipment Tires.
- Equipment such as the Hunter GSP9700 MUST be calibrated prior to measuring tire/wheel assemblies for each vehicle.

The purpose of this bulletin is to provide guidance to GM dealers when using tire force variation measurement equipment, such as the Hunter
GSP9700. This type of equipment can be a valuable tool in diagnosing vehicle ride concerns. The most common ride concern involving tire radial
force variation is highway speed shake on smooth roads.

Tire related smooth road highway speed shake can be caused by three conditions: imbalance, out of round and tire force variation. These three
conditions are not necessarily related. All three conditions must be addressed.

Imbalance is normally addressed first, because it is the simpler of the three to correct. Off-vehicle, two plane dynamic wheel balancers are readily
available and can accurately correct any imbalance. Balancer calibration and maintenance, proper attachment of the wheel to the balancer, and
proper balance weights, are all factors required for a quality balance. However, a perfectly balanced tire/wheel assembly can still be "oval shaped"
and cause a vibration.

Before balancing, perform the following procedures.

Tire and Wheel Diagnosis


1. Set the tire pressure to the placard values.
2. With the vehicle raised, ensure the wheels are centered on the hub by loosening all wheel nuts and hand-tightening all nuts first by hand
while shaking the wheel, then torque to specifications using a torque wrench, NOT a torque stick.
3. Visually inspect the tires and the wheels. Inspect for evidence of the following conditions and correct as necessary:

- Missing balance weights


- Bent rim flange
- Irregular tire wear
- Incomplete bead seating
- Tire irregularities (including pressure settings)
- Mud/ice build-up in wheel
- Stones in the tire tread
- Remove any aftermarket wheels and/or tires and restore vehicle to original condition prior to diagnosing a smooth road shake condition.

4. Road test the vehicle using the Electronic Vibration Analyzer (EVA) essential tool. Drive for a sufficient distance on a known, smooth road
surface to duplicate the condition. Determine if the vehicle is sensitive to brake apply. If the brakes are applied lightly and the pulsation felt
in the steering wheel increases, refer to the Brakes section of the service manual that deals with brake-induced pulsation. If you can start to
hear the vibration as a low boom noise (in addition to feeling it), but cannot see it, the vehicle likely has a first order (one pulse per propshaft
revolution) driveline vibration. Driveline first order vibrations are high enough in frequency that most humans can start to hear them at
highway speeds, but are too high to be able to be easily seen. These issues can be caused by driveline imbalance or misalignment. If the
vehicle exhibits this low boom and the booming pulses in-and-out on a regular basis (like a throbbing), chances are good that the vehicle
could have driveline vibration. This type of vibration is normally felt more in the "seat of the pants" than the steering wheel.
5. Next, record the Hertz (Hz) reading as displayed by the EVA onto the tire data worksheet found at the end of this bulletin. This should be
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 643
Chevrolet Venture V6-3.4L VIN E 2968
done after a tire break-in period of at least 16 km (10 mi) at 72 km/h (45 mph) or greater, in order to eliminate any possible tire flat-spotting.
This reading confirms what the vehicle vibration frequency is prior to vehicle service and documents the amount of improvement occurring
as the result of the various steps taken to repair. Completing the Steering Wheel Shake Worksheet below is required. A copy of the
completed worksheet must be saved with the R.O. and a copy included with any parts returned to the Warranty Parts Center for analysis. A
reading of 35 to 50 Hz typically indicates a first order propshaft vibration. If this is the situation, refer to Corporate Bulletin Number
08-07-30-044D. Generally, a reading between 10 and 20 Hz indicates a tire/wheel vibration and if this is the reading obtained, continue using
this bulletin.
If the tire 1st order vibration goes away and stays away during this evaluation, the cause is likely tire flat-spotting. Tire flat-spotting vibration
may come and go at any speed over 72 km/h (45 mph) during the first 10 minutes of operation, if vibration continues after 10 minutes of
driving at speeds greater than 72 km/h (45 mph), tire flat-spotting can be ruled out as the cause for vibration.
6. If flat-spotting is the cause, provide the explanation that this has occurred due to the vehicle being parked for long periods of time and that
the nature of the tire is to take a set. Refer to Corporate Bulletin Number 03-03-10-007E: Information on Tire/Wheel Characteristics
(Vibration, Balance, Shake, Flat Spotting) of GM Original Equipment Tires.
7. If the road test indicates a shake/vibration exists, check the imbalance of each tire/wheel assembly on a known, calibrated, off-car dynamic
balancer.Make sure the mounting surface of the wheel and the surface of the balancer are absolutely clean and free of debris. Be sure
to chose the proper cone/collet for the wheel, and always use the pilot bore for centering. Never center the wheel using the hub-cap
bore since it is not a precision machined surface. If any assembly calls for more than 1/4 ounce on either rim flange, remove all balance
weights and rebalance to as close to zero as possible. If you can see the vibration (along with feeling it) in the steering wheel (driving straight
without your hands on the wheel), it is very likely to be a tire/wheel first order (one pulse per revolution) disturbance. First order disturbances
can be caused by imbalance as well as non-uniformities in tires, wheels or hubs. This first order frequency is too low for a human to hear, but
if the amplitude is high enough, it can be seen.

If a vibration or shake still exists after balancing, any out of round conditions, of the wheel, and force variation conditions of the tire, must be
addressed. Equipment such as the Hunter GSP9700 can address both (it is also a wheel balancer).

Tire radial force vibration (RFV) can be defined as the amount of stiffness variation the tire will produce in one revolution under a constant load.
Radial force variation is what the vehicle feels because the load (weight) of the vehicle is always on the tires. Although free runout of tires (not
under load) is not always a good indicator of a smooth ride, it is critical that total tire/wheel assembly runout be within specification.

Equipment such as the Hunter GSP9700 loads the tire, similar to on the vehicle, and measures radial force variation of the tire/wheel assembly.
Note that the wheel is affecting the tire's RFV measurement at this point. To isolate the wheel, its runout must be measured. This can be easily done
on the Hunter, without the need to set up dial indicators. If the wheel meets the runout specification, the tire's RFV can then be addressed.

After measuring the tire/wheel assembly under load, and the wheel alone, the machine then calculates (predicts) the radial force variation of the tire.
However, because this is a prediction that can include mounting inaccuracies, and the load wheel is much smaller in diameter than used in tire
production, this type of service equipment should NOT be used to audit new tires. Rather, it should be used as a service diagnostic tool to minimize
radial force variation of the tire/wheel assembly.

Equipment such as the Hunter GSP9700 does an excellent job of measuring wheel runout, and of finding the low point of the wheel (for runout)
and the high point of the tire (for radial force variation). This allows the tire to be matched mounted to the wheel for lowest tire/wheel assembly
force variation.

The machine will simplify this process into easy steps. The following assembly radial force variation numbers should be used as a guide:

When measuring RFV and match mounting tires perform the following steps.

Measuring Wheel Runout and Assembly Radial Force Variation

Important
The completed worksheet at the end of this bulletin must be attached to the hard copy of the repair order.

- Measure radial force variation and radial runout.


- If a road force/balancing machine is used, record the radial force variation (RFV) on the worksheet at the end of this bulletin. It may be of
benefit to have the lowest RFV assembly to the front left corner. If the machine is not available and the EVA data suggests there is an issue,
swap the tire and wheel assemblies from the front to the back. Re-check on the EVA and if the problem still exists, test another vehicle to
find tires that do not exhibit the same frequency and swap those tires onto the subject vehicle.
- If a runout/balancing machine is used, record the radial runout of the tire/wheel assemblies on the worksheet at the end of this bulletin. If one
or more of the tire/wheel assemblies are more than.040 in (1.02 mm), match mount the tire to the wheel to get below.040 in (1.02 mm). For
sensitive customers, readings of 0.030 inch (0.76 mm) or less are preferable, it may also be of benefit to have the lowest runout assembly to
the front left corner. If the machine is not available and the EVA data suggests there is an issue, swap the tire and wheel assemblies from the
front to the back. Re-check on the EVA and if the problem still exists, test another vehicle to find tires that do not exhibit the same frequency
and swap those tires onto the subject vehicle.
- After match mounting, the tire/wheel assembly must be rebalanced.
If match mounting tires to in-spec wheels produces assembly values higher than these, tire replacement may be necessary. Replacing tires at lower
values will probably mean good tires are being condemned. Because tires can sometimes become temporarily flat-spotted, which will affect force
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 644
Chevrolet Venture V6-3.4L VIN E 2969
variation, it is important that the vehicle be driven at least 16 km (10 mi) prior to measuring. Tire pressure must also be adjusted to the usage
pressure on the vehicle's tire placard prior to measuring.

Most GM vehicles will tolerate radial force variation up to these levels. However, some vehicles are more sensitive, and may require lower levels.
Also, there are other tire parameters that equipment such as the Hunter GSP9700 cannot measure that may be a factor. In such cases, TAC should
be contacted for further instructions.

Important

- When mounting a GM wheel to a wheel balancer/force variation machine, always use the wheel's center pilot hole. This is the
primary centering mechanism on all GM wheels; the bolt holes are secondary. Usually a back cone method to the machine should be
used. For added accuracy and repeatability, a flange plate should be used to clamp the wheel onto the cone and machine. This system
is offered by all balancer manufacturers in GM's dealer program.
- Any type of service equipment that removes tread rubber by grinding, buffing or truing is NOT recommended, and may void the tire
warranty. However, tires may have been ground by the tire company as part of their tire manufacturing process. This is a legitimate
procedure.

Steering Wheel Shake Worksheet

When diagnosing vibration concerns, use the following worksheet in conjunction with the appropriate Vibration Analysis-Road testing procedure
in the Vibration Correction sub-section in SI.
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 645
Chevrolet Venture V6-3.4L VIN E 2970

Refer to the appropriate section of SI for specifications and repair procedures that are related to the vibration concern.

Disclaimer

Technical Service Bulletin # 06-03-10-010A Date: 100609

Wheels - Changing Procedures/Precautions


INFORMATION
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 646
Chevrolet Venture V6-3.4L VIN E 2971

Bulletin No.: 06-03-10-010A

Date: June 09, 2010

Subject: Information on Proper Wheel Changing Procedures and Cautions

Models:

2011 and Prior GM Passenger Cars and Trucks


2010 and Prior HUMMER Models
2005-2009 Saab 9-7X
2005-2009 Saturn Vehicles

Attention:

Complete wheel changing instructions for each vehicle line can be found under Tire and Wheel Removal and Installation in Service Information
(SI). This bulletin is intended to quickly review and reinforce simple but vital procedures to reduce the possibility of achieving low torque during
wheel installation. Always refer to SI for wheel lug nut torque specifications and complete jacking instructions for safe wheel changing.

Supercede:
This bulletin is being revised to include the 2011 model year and update the available special tool list. Please discard Corporate Bulletin Number
06-03-10-010 (Section 03 - Suspension).

Frequency of Wheel Changes - Marketplace Driven

Just a few years ago, the increasing longevity of tires along with greater resistance to punctures had greatly reduced the number of times wheels
were removed to basically required tire rotation intervals. Today with the booming business in accessory wheels/special application tires (such as
winter tires), consumers are having tire/wheel assemblies removed - replaced - or installed more than ever. With this increased activity, it opens up
more of a chance for error on the part of the technician. This bulletin will review a few of the common concerns and mistakes to make yourself
aware of.

Proper Servicing Starts With the Right Tools

The following tools have been made available to assist in proper wheel and tire removal and installation.

- J 41013 Rotor Resurfacing Kit (or equivalent)


- J 42450-A Wheel Hub Resurfacing Kit (or equivalent)

Corroded Surfaces

One area of concern is corrosion on the mating surfaces of the wheel to the hub on the vehicle. Excessive corrosion, dirt, rust or debris built up on
these surfaces can mimic a properly tightened wheel in the service stall. Once the vehicle is driven, the debris may loosen, grind up or be washed
away from water splash. This action may result in clearance at the mating surface of the wheel and an under-torqued condition.

Caution

Before installing a wheel, remove any buildup on the wheel mounting surface and brake drum or brake disc mounting surface. Installing wheels
with poor metal-to-metal contact at the mounting surfaces can cause wheel nuts to loosen. This may cause a wheel to come off when the vehicle is
moving, possibly resulting in a loss of control or personal injury.

Whenever you remove the tire/wheel assemblies, you must inspect the mating surfaces. If corrosion is found, you should remove the debris with a
die grinder equipped with a fine sanding pad, wire brush or cleaning disc. Just remove enough material to assure a clean, smooth mating surface.

The J 41013 (or equivalent) can be used to clean the following surfaces:

- The hub mounting surface


- The brake rotor mounting surface
- The wheel mounting surface

Use the J 42450-A (or equivalent) to clean around the base of the studs and the hub.

Lubricants, Grease and Fluids

Some customers may use penetrating oils, grease or other lubricants on wheel studs to aid in removal or installation. Always use a suitable
cleaner/solvent to remove these lubricants prior to installing the wheel and tire assemblies. Lubricants left on the wheel studs may cause improper
readings of wheel nut torque. Always install wheels to clean, dry wheel studs ONLY.

Notice
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 647
Chevrolet Venture V6-3.4L VIN E 2972
Lubricants left on the wheel studs or vertical mounting surfaces between the wheel and the rotor or drum may cause the wheel to work itself loose
after the vehicle is driven. Always install wheels to clean, dry wheel studs and surfaces ONLY.
Beginning with 2011 model year vehicles, put a light coating of grease, GM P/N 1051344 (in Canada, P/N 9930370), on the inner surface of the
wheel pilot hole to prevent wheel seizure to the axle or bearing hub.

Wheel Stud and Lug Nut Damage

Always inspect the wheel studs and lug nuts for signs of damage from crossthreading or abuse. You should never have to force wheel nuts down
the stud. Lug nuts that are damaged may not retain properly, yet give the impression of fully tightening. Always inspect and replace any component
suspected of damage.

Tip

Always start wheel nuts by hand! Be certain that all wheel nut threads have been engaged BEFORE tightening the nut.

Important
If the vehicle has directional tread tires, verify the directional arrow on the outboard side of the tire is pointing in the direction of forward
rotation.

Wheel Nut Tightening and Torque

Improper wheel nut tightening can lead to brake pulsation and rotor damage. In order to avoid additional brake repairs, evenly tighten the wheel
nuts to the proper torque specification as shown for each vehicle in SI. Always observe the proper wheel nut tightening sequence as shown below in
order to avoid trapping the wheel on the wheel stud threads or clamping the wheel slightly off center resulting in vibration.

The Most Important Service You Provide

While the above information is well known, and wheel removal so common, technicians run the risk of becoming complacent on this very
important service operation. A simple distraction or time constraint that rushes the job may result in personal injury if the greatest of care is not
exercised. Make it a habit to double check your work and to always side with caution when installing wheels.

Disclaimer
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 648
Chevrolet Venture V6-3.4L VIN E 2973

Technical Service Bulletin # 03-08-98-002B Date: 100630

Body - Squeeze Type Resistance Spot Welding/Equipment


INFORMATION

Bulletin No.: 03-08-98-002B

Date: June 30, 2010

Subject: Squeeze Type Resistance Spot Welding/Equipment

Models:

2011 and Prior Passenger Cars and Trucks (Including Saturn)


2003-2010 HUMMER H2, H3

Supercede:
This bulletin is being revised to add model years. Please discard Corporate Bulletin Number 03-08-98-002A (Section 08 - Body and Accessories).

This bulletin provides guidelines for repair shops that wish to use squeeze type resistance spot welding (or simply, spot welding) as an alternative to
MIG plug welding when performing collision repair procedures. The process of spot welding for attaching body panels and components has been
around for many years and is similar to the production welding process used in assembly plants. Spot welding may be applicable in similar
situations that are currently MIG plug welded.

The following are some of the benefits of spot welding:

- Less heat or burn damage


- Less damage to corrosion protection
- Drilling of holes not required
- Replication of the production weld appearance

Applicable components for this technology may be panels or components with flanges that are accessible with arms and tips supplied by the
equipment manufacturer. Welds from this equipment should be applied on a one-for-one basis, next to the production welds.

Here are some of the important factors in proper welding with this equipment.

Important
Proper use and safety training for each user of the equipment is a must.

- Use equipment from companies that are able to produce welds that meet industry standards for size and strength.
Equipment most likely to meet those standards at this time would be "inverter" technology and include the following suppliers (other
suppliers may have comparable equipment):

- Pro Spot (PR2000)


- Elektron (M100)
- Blackhawk (WEL700)
- Car-O-Liner (CR500)
For specific information about this and other equipment, call GM Dealer Equipment.

- Ensure that the building power source is capable of meeting the equipment manufacturer's power requirement specifications.
For example, fuse 60 amp, 208-230 V single or 3-phase, using supply wire of sufficient gauge to carry the current load. Consult with a
qualified electrician for wiring assistance.
- Prepare and perform sample welds for destructive testing made from similar materials. Perform this operation for each vehicle repaired and
prior to actual repair.
- Proper equipment maintenance
- Proper weld tip alignment and maintenance
- Ensure that metal flanges are clean and conform to each other

A more complete description of these practices and standards can be found in the following publications:

- SAE J-2667, Surface Vehicles Recommended Practice, http://www.sae.org


- AWS D8.7-88, Recommended Practices Automotive Weld Quality - Resistance Spot Welding, http://www.aws.org/w/a/
- AWS D8.9-97, Recommended Practices for Test Methods for Evaluating the Resistance Spot Welding Behavior of Automotive Sheet Steels,
http://www.aws.com
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 649
Chevrolet Venture V6-3.4L VIN E 2974

Disclaimer

Technical Service Bulletin # 08-08-42-005B Date: 090611

Lighting - Headlamp Replacement Information


INFORMATION

Bulletin No.: 08-08-42-005B

Date: June 11, 2009

Subject: Replacement of Headlamp Assemblies Under Warranty and Use of GM vs. Non-GM Headlamp Assemblies

Models:

2010 and Prior GM Passenger Cars and Trucks (Including Saturn and Saab)
2010 and Prior HUMMER H2, H3

Supercede:
This bulletin is being revised to update parts identification and model years. Please discard Corporate Bulletin Number 08-08-42-005A (Section 08
- Body and Accessories).

This bulletin is being issued to inform dealers that whenever a headlamp replacement under warranty is necessary, be sure to use the correct
General Motors (GM) approved headlamp assembly.

Recent Warranty Parts Center reviews of headlamps replaced in the field show that some dealers have returned non-GM (counterfeit) headlamp
assemblies under warranty.

These non-GM headlamp assemblies (referred to as "knock-offs") are not made to GM specifications. Also, the appearance of these headlamp
assemblies are very close to the genuine parts. Refer to the figures below.
Non-GM or "Knockoff" Part

The figure above shows a non-GM or "knockoff" headlamp assembly. The lens stamping will read "EAGLE EYES." There are other companies
that manufacture replacement lamps that can be installed on a variety of GM vehicles.

These non-GM headlamp assemblies will not be honored under warranty. These are not original equipment and are not sanctioned as replacement
parts by GM.

Disclaimer

Technical Service Bulletin # 02-08-42-001D Date: 100621


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 650
Chevrolet Venture V6-3.4L VIN E 2975
Lighting - Headlamp Polycarbonate Lens Damage Prevention
INFORMATION

Bulletin No.: 02-08-42-001D

Date: June 21, 2010

Subject: Headlamp Lens Overheating When Covered and Chemical Damage to Exterior Polycarbonate Headlamp Lenses

Models:

2011 and Prior GM Passenger Cars and Trucks (Including Saturn)


2010 and Prior HUMMER H2, H3
2009 and Prior Saab 9-7X

Supercede:
This bulletin is being revised to add model years and to revise the warning statements. Please discard Corporate Bulletin Number 02-08-42-001C
(Section 08 - Body and Accessories).

The bulletin is being issued to make dealers and customers aware of chemical damage that may be caused to exterior polycarbonate headlamp
lenses. Most late model vehicles have these types of headlamp lenses. This material is used because of its temperature and high impact resistance.

A variety of chemicals can cause crazing or cracking of the headlamp lens. Headlamp lenses are very sensitive. Care should be exercised to avoid
contact with all exterior headlamp lenses when treating a vehicle with any type of chemical, such as those recommended for rail dust removal.
Rubbing compound, grease tar and oil removers, tire cleaners, cleaner waxes and even car wash soaps in too high a concentration may also attribute
to this condition. This could result in the need to replace the entire headlamp housing.

Warning

Use only lukewarm or cold water, a soft cloth and a car washing soap to clean exterior lamps and lenses.

Also, crazing or deformations of the lens may occur if a shop mat or fender cover is draped over the fender and covers a portion or all of the
headlamp assembly while the DRL or headlamps are on. This action restricts the amount of heat dissipated by the headlamps.

Warning

Care should be taken to not cover headlamps with shop mats or fender covers if the vehicle is being serviced with the headlamps or DRL
illuminated. Covering an illuminated lamp can cause excessive heat build up and crazing/deformation of the lens may occur. The degradation of the
lens can be unnoticeable at first and eventually become hairline cracks in the lens. In extreme cases, it could cause the lens to deform. This damage
can also be caused by aftermarket shields that are often tinted in color.

Once a heat buildup is generated by the headlamp, a degradation of the headlamp lens begins. This degradation of the lens can be unnoticeable at
first and eventually manifest as spider cracks. In more extreme cases, it will begin to melt the lens of the headlamp.

Notice

Headlamps damaged by chemicals, improper cleaning, or overheating due to being covered are not covered under the new vehicle warranty.

Disclaimer

Technical Service Bulletin # 06-08-51-005A Date: 100630

Body - Hem Flange Sealer For Corrosion Protection


INFORMATION

Bulletin No.: 06-08-51-005A

Date: June 30, 2010

Subject: Information on Hem Flange Sealer for Corrosion Protection

Models:
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 651
Chevrolet Venture V6-3.4L VIN E 2976

2011 and Prior Passenger Cars and Trucks (Including Saturn and Saab)
2010 and Prior HUMMER H2, H3

Attention:

Please direct this bulletin to the Body Shop or any areas of your dealership where sheet metal replacement or corrosion repairs take place.

Supercede:
This bulletin is being revised to add model years. Please discard Corporate Bulletin Number 06-08-51-005 (Section 08 - Body and Accessories).

Replacement Sheet Metal

Metal or aluminum overlap joints and seams, commonly referred to as hem flanges, on replacement doors, hoods, decklids and liftgates should be
sealed to prevent moisture from entering the bonded hem flange using a quality 2K sealer such as the following products, or equivalent:

- Lord Fusor 123EZ / 126EZ Non-Sag seam sealer


- 3M 8308 Ultrapro sealer
- Crest CT-NT Thick-n-Tan
- Crest CB-M1 Black Majik
- Kent E-6000 Non-Sag seal sealer

The applied sealer must meet the following criteria:

- The sealer must be free of skips using a ribbon tip to locate the bead over the edge of the hem. Refer to the following illustration.
- The sealer must cover all edges with a bead width of approximately 10 mm (0.39 in) and approximately 2 mm (0.08 in) thick.
- The sealer must be paintable.
- The sealer must retain its flexible characteristics after curing.
- The sealer must not block a water drain path.

Always use Genuine GM replacement sheet metal.

Disclaimer

Technical Service Bulletin # 03-00-89-008E Date: 100701

Body - Metal Body Panel Corrosion Protection


INFORMATION

Bulletin No.: 03-00-89-008E

Date: July 01, 2010

Subject: Corrosion Protection for Metal Panels with Dealer Installed Accessories Fastened by Drilled Holes
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 652
Chevrolet Venture V6-3.4L VIN E 2977

Models:

2011 and Prior GM Passenger Cars and Trucks (Including Saturn)


2003-2009 HUMMER H2
2006-2010 HUMMER H3

Supercede:
This bulletin is being revised to update the model years. Please discard Corporate Bulletin Number 03-00-89-008D (Section 00 - General
Information).

Corrosion Concerns

Frequently, dealer installed accessories, whether aftermarket or GM-approved, may require drilling holes into the body panels or supports to
complete installation. Whenever you drill into a metal surface, the corrosion resistance of that panel is compromised. Testing was conducted to
determine the best method used to protect the fastener-to-panel mounting holes from future corrosion. Several commercially available sealers and
coatings were evaluated.

Recommendations

In all cases, GM Vehicle Care Super Lube(R) with PTFE performed the best at preventing corrosion in fastener to panel interface holes and is now
the official GM recommended product as shown in the above illustration. It is recommended to apply the GM Vehicle Care Super Lube(R) with
PTFE to any hole and fastener before installing the fastener into the drilled attaching hole or inside the metal panel.

Important
GM Vehicle Care Super Lube(R) with PTFE is the only product recommended and required by GM for the corrosion protection of metal
panels where fasteners will be added to metal panels.

Parts Information

Disclaimer

Technical Service Bulletin # 99-09-40-005F Date: 100623

Restraints - Extender Availability For Seat Belt


INFORMATION

Bulletin No.: 99-09-40-005F

Date: June 23, 2010

Subject: Seat Belt Extender Availability

Models:
2011 and Prior GM Passenger Cars and Trucks (Including Saturn)
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 653
Chevrolet Venture V6-3.4L VIN E 2978
2009 and Prior HUMMER H2
2010 and Prior HUMMER H3
2005-2009 Saab 9-7X

Supercede:

This bulletin is being revised to add the 2009&hyphen;2011 model years and update the Warranty Information. Please discard Corporate Bulletin
Number 99-09-40-005E (Section 09 Restraints).

Important:

DO NOT use belt extenders when securing a child restraint.

The seat and shoulder belt restraint systems used in all General Motors vehicles have sufficient belt length to accommodate most drivers and
passengers. Consequently, requests for belt extensions (extenders) should be minimal.

Seat belt extenders are available ONLY IN BLACK for most GM passenger cars and trucks produced in recent years. They are available in two
different lengths, 23 cm (9 in) and 38 cm (15 in). They are designed to be coupled with the existing belts in each vehicle. When in use, the extender
makes the belt arrangement a "custom fit" and use by anyone else or in another vehicle will lessen or nullify the protection offered by the vehicle's
restraint system. For this reason, it is extremely important that the correct length extender be used for the vehicle and occupant intended.

Important:

Do not use an extender just to make it easier to buckle the safety belt. Use an extender only when you cannot buckle the safety belt without using an
extender.

Parts Information

For part numbers, usage and availability of extenders, see Extension Kit in Group 14.875 (cars) or Group 16.714 (trucks) of the appropriate parts
catalog. Saturn retailers should refer to the appropriate model year Parts & Illustration catalog for the vehicle. U.S. Saab dealers should contact the
Parts Help line. Canadian Saab dealers should fax requests to Partech Canada.

Warranty Information

^ Seat belt extenders are a NO CHARGE item to all GM customers who request them for their specific vehicles.

^ Dealers should not be charging part costs since these extenders are supplied by GM to the dealers.

^ Dealers should not be charging labor costs since the extender can be customer installed.

DisclaimerTechnical Service Bulletin # 10-00-89-010 Date: 100527

Locks - Key Code Security Rules and Information


INFORMATION

Bulletin No.: 10-00-89-010

Date: May 27, 2010

Subject: Key Code Security Rules and Information on GM KeyCode Look-Up Application (Canada Only)

Models:

2011 and Prior GM Passenger Cars and Trucks


2010 and Prior HUMMER H2, H3
2009 and Prior Saturn and Saab
2002 and Prior Isuzu

Attention:

This bulletin has been created to address potential issues and questions regarding KeyCode security. This bulletin should be read by all parties
involved in KeyCode activity, including dealer operator, partner security coordinator, sales, service and parts departments. A copy of this bulletin
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 654
Chevrolet Venture V6-3.4L VIN E 2979
should be printed and maintained in the parts department for use as a reference.

Important
U.S. dealers should refer to Corporate Bulletin Number 10-00-89-009.

Where Are Key Codes Located?

General Motors provides access to KeyCodes through three sources when a vehicle is delivered to a dealer. Vehicle KeyCodes are located on the
original vehicle invoice to the dealership. There is a small white bar coded tag sent with most new vehicles that also has the key code printed on it.
Dealerships should make a practice of comparing the tag's keycode numbers to the keycode listed on the invoice. Any discrepancy should be
reported immediately to the GM of Canada Key Code Inquiry Desk. Remember to remove the key tag prior to showing vehicles to potential
customers. The third source for Key codes is through the GM KeyCode Look-Up feature within the OEConnection D2DLink application. KeyCode
Look-Up currently goes back 17 previous model years from the current model year.

When a vehicle is received by the dealership, care should be taken to safeguard the original vehicle invoice and KeyCode tag provided with the
vehicle. Potential customers should not have access to the invoice or this KeyCode tag prior to the sale being completed. After a sale has been
completed, the KeyCode information belongs to the customer and General Motors.

Tip

Only the original invoice contains key code information, a re-printed invoice does not.

GM KeyCode Look-Up Application for GM of Canada Dealers

All dealers should review the General Motors of Canada KeyCode Look-Up Policies and Procedures (Service Policy & Procedures Manual Section
3.1.6 "Replacement of VIN plates & keys").

Please note that the KeyCode Access site is restricted. Only authorized users should be using this application. Please see your Parts Manager for
site authorized users. KeyCode Look-Up currently goes back 17 years from current model year.

Important notes about security:

- Users may not access the system from multiple computers simultaneously.
- Users may only request one KeyCode at a time.
- KeyCode information will only be available on the screen for 2 minutes.
- Each user is personally responsible for maintaining and protecting their password.
- Never share your password with others.
- User Id's are suspended after 6 consecutive failed attempts.
- User Id's are disabled if not used for 90 days.
- Processes must be in place for regular dealership reviews.
- The Parts Manager (or assigned management) must have processes in place for employee termination or life change events. Upon termination
individuals access must be turned off immediately and access should be re-evaluated upon any position changes within the dealership.
- If you think your password or ID security has been breached, contact Dealer Systems Support at 1-800-265-0573.

Each user will be required to accept the following agreement each time the KeyCode application is used.

Key Code User Agreement

- Key codes are proprietary information belonging to General Motors Corporation and to the vehicle owner.
- Unauthorized access to, or use of, key code information is unlawful and may subject the user to criminal and civil penalties.
- This information should be treated as strictly confidential and should not be disclosed to anyone unless authorized.

I will ensure that the following information is obtained prior to releasing any Key Code information:

1. Government issued picture ID (Drivers License)


2. Registration or other proof of ownership. Registration should have normal markings from the Province that issued the registration and
possibly the receipt for payment recorded as well.

Important
- GM takes this agreement seriously. Each user must be certain of vehicle ownership before giving out key codes.
- When the ownership of the vehicle is in doubt, dealership personnel should not provide the information.
- Key code requests should never be received via a fax or the internet and key codes should never be provided to anyone in this
manner. A face to face contact with the owner of the vehicle is the expected manner that dealers will use to release a key code or as
otherwise stipulated in this bulletin or other materials.
- Key codes should NEVER be sent via a fax or the internet.
- Each Dealership should create a permanent file to document all KeyCode Look Up transactions. Requests should be filed by VIN
and in each folder retain copies of the following:

- Government issued picture ID (Drivers License)


- Registration or other proof of ownership.
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 655
Chevrolet Venture V6-3.4L VIN E 2980
- Copy of the paid customer receipt which has the name of the employee who cut and sold the key to the customer.

- Do not put yourself or your Dealership in the position of needing to "explain" a KeyCode Look Up to either GM or law enforcement
officials.
- Dealership Management has the ability to review all KeyCode Look-Up transactions.
- Dealership KeyCode documentation must be retained for two years.

Frequently Asked Questions (FAQs) for GM of Canada Dealers

How do I request a KeyCode for customer owned vehicle that is not registered?

Scrapped, salvaged or stored vehicles that do not have a current registration should still have the ownership verified by requesting the vehicle title,
current insurance policy and / or current lien holder information from the customers financing source. If you cannot determine if the customer is the
owner of the vehicle, do not provide the key code information. In these cases, a short description of the vehicle (scrapped, salvaged, etc.) and the
dealership location should be kept on file. Any clarifying explanation should be entered into the comments field.

How do I document a KeyCode request for a vehicle that is being repossessed?

The repossessor must document ownership of the vehicle by providing a court ordered repossession order and lien-holder documents prior to
providing key code information. Copies of the repossessors Drivers License and a business card should be retained by the dealership for
documentation.

What do I do if the registration information is locked in the vehicle?

Every effort should be made to obtain complete information for each request. Each Dealership will have to decide on a case by case basis if enough
information is available to verify the customer's ownership of the vehicle. Other forms of documentation include vehicle title, insurance policy, and
or current lien information from the customers financing source. Dealership Management must be involved in any request without complete
information. If you cannot determine if the customer is the owner of the vehicle, do not provide the key code information.

Can I get a print out of the information on the screen?

It is important to note that the Key Code Look Up Search Results contain sensitive and/or proprietary information. For this reason GM recommends
against printing it. If the Search Results must be printed, store and/or dispose of the printed copy properly to minimize the risk of improper or
illegal use.

Who in the dealership has access to the KeyCode application?

Dealership Parts Manager (or assigned management) will determine, and control, who is authorized to access the KeyCode Look Up application.
However, we anticipate that dealership parts and service management will be the primary users of the application. The KeyCode Look Up
application automatically tracks each user activity session. Information tracked by the system includes: User name, User ID, all other entered data
and the date/time of access.

What if I input the VIN incorrectly?

If an incorrect VIN is entered into the system (meaning that the system does not recognize the VIN or that the VIN has been entered incorrectly) the
system will return an error message.

If I am an authorized user for the KeyCode application, can I access the application from home?

Yes.

What if I suspect key code misuse?

Your dealership should communicate the proper procedures for requesting key codes. Any suspicious activity either within the dealership or
externally should be reported to Dealer Systems Support at 1-800-265-0573 or GM of Canada Key Code Inquiry Desk at 1-905-644-4892.

Whose key codes can I access through the system?

At this time the following Canadian vehicle codes are available through the system: Chevrolet, Cadillac, Buick, Pontiac, GMC, HUMMER (H2 and
H3 only), Oldsmobile, Saturn, Saab and Isuzu (up to 2002 model year) for a maximum of 17 model years.

What should I do if I enter a valid VIN and the system does not produce any key code information?

Occasionally, the KeyCode Look Up application may not produce a key code for a valid VIN. This may be the result of new vehicle information
not yet available. In addition, older vehicle information may have been sent to an archive status. If you do not receive a key code returned for valid
VIN, you should contact GM of Canada Key Code Inquiry Desk at 1-905-644-4892.

How do I access KeyCodes if the KeyCode Look-up system is down?

If the KeyCode Look-up system is temporarily unavailable, you can contact the original selling dealer who may have it on file or contact GM of
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 656
Chevrolet Venture V6-3.4L VIN E 2981
Canada Key Code Inquiry Desk at 1-905-644-4892. If the customer is dealing with an emergency lock-out situation, you need to have the customer
contact Roadside assistance, OnStar if subscribed, or 911.

What should I do if the KeyCode from the look-up system does not work on the vehicle?

On occasion a dealer may encounter a KeyCode that will not work on the vehicle in question. In cases where the KeyCode won't work you will
need to verify with the manufacturer of the cutting equipment that the key has been cut correctly. If the key has been cut correctly you may be able
to verify the proper KeyCode was given through the original selling dealer. When unable to verify the KeyCode through the original selling dealer
contact GM of Canada Key Code Inquiry Desk at 1-905-644-4892. If the key has been cut correctly and the code given does not work, the lock
cylinder may have been changed. In these situations following the proper SI document for recoding a key or replacing the lock cylinder may be
necessary.

How long do I have to keep KeyCode Records?

Dealership KeyCode documentation must be retained for two years.

Can I get a KeyCode changed in the Look-Up system?

Yes, KeyCodes can be changed in the Look-Up system if a lock cylinder has been changed. Contact GM of Canada Key Code Inquiry Desk at
1-905-644-4892.

What information do I need before I can provide a driver of a company fleet vehicle Keys or KeyCode information?

The dealership should have a copy of the individual's driver's license, proof of employment and registration. If there is any question as to the
customer's employment by the fleet company, the dealer should attempt to contact the fleet company for verification. If there is not enough
information to determine ownership and employment, this information should not be provided.

How do I document a request from an Independent Repair facility for a KeyCode or Key?

The independent must provide a copy of their driver's license, proof of employment and signed copy of the repair order for that repair facility. The
repair order must include customer's name, address, VIN, city, province and license plate number. Copies of this information must be included in
your dealer KeyCode file.

Disclaimer

Technical Service Bulletin # 04-08-50-006D Date: 100909

Interior - Seat Cover Wrinkle/Crease/Burn Info


INFORMATION

Bulletin No.: 04-08-50-006D

Date: September 09, 2010

Subject: Minor Wrinkles/Creases, Discoloration, Cigarette Burns and Customer Induced Cuts and Stains on Front and Rear Driver and Passenger
Seats with Leather, Vinyl or Cloth Seat Covers

Models:

2011 and Prior GM Passenger Cars and Light Duty Trucks


2009 and Prior HUMMER H2
2010 and Prior HUMMER H3
2009 and Prior Saab 9-7X
2010 and Prior Saturn

Supercede:
This bulletin is being revised to add a model year. Please discard Corporate Bulletin Number 04-08-50-006C (Section 08 - Body and Accessories).

If a customer comes in to your dealership due to certain conditions of the seat covers (splits, wrinkles, loose stitching, etc.), you must examine the
seat cover in order to determine the validity of the customer claim. Some components from the above listed vehicles have been returned to the
Warranty Parts Center (WPC) and analysis of these parts showed "customer induced damage" or No Trouble Found (NTF).
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 657
Chevrolet Venture V6-3.4L VIN E 2982

The dealer should pay particular attention to the following conditions:

- Cigarette burns

- Customer induced cuts (knife cuts, cut by customer tools, etc.)


- Paint stains (customer should have cleaned paint stains while paint was still wet)
- Coffee stains and other removable dirt
These should be cleaned as described in the Owner's Manual under Appearance Care. Also, refer to Corporate Bulletin Number
06-00-89-029A or later.
- Evidence of chemicals used for cleaning, other than those specified in the Owner's Manual
- Other chemical spills
- Minor and normal leather wrinkles as a result of use
- Other defects to the seat cover not detected during the pre-delivery inspection (PDI).

Inform the customer that the above issues were not present when the vehicle was purchased and cannot be replaced under warranty. The
covers, however, may be repaired or replaced at the customer's expense.
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 658
Chevrolet Venture V6-3.4L VIN E 2983

The following conditions are not caused by the customer and should be covered by warranty:

- Split seams

- Wear/cracking/peeling
- Discoloration/dye transfer from customer clothing (if discoloration/dye transfer is not removed after using GM Leather and Vinyl Plastic
Cleaner, P/N 88861401 (in Canada, P/N 88861409), replace the covers.)

Disclaimer

Technical Service Bulletin # 08-07-30-035B Date: 101101

A/T - Water Or Coolant Contamination Information


INFORMATION

Bulletin No.: 08-07-30-035B

Date: November 01, 2010

Subject: Information on Water or Ethylene Glycol in Transmission Fluid

Models:

2011 and Prior GM Passenger Cars and Light Duty Trucks


with Automatic Transmission

Supercede:
This bulletin is being revised to update model years. Please discard Corporate Bulletin Number 08-07-30-035A (Section 07 -
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 659
Chevrolet Venture V6-3.4L VIN E 2984
Transmission/Transaxle).

Water or ethylene glycol in automatic transmission fluid (ATF) is harmful to internal transmission components and will have a negative effect on
reliability and durability of these parts. Water or ethylene glycol in ATF will also change the friction of the clutches, frequently resulting in shudder
during engagement or gear changes, especially during torque converter clutch engagement.

Indications of water in the ATF may include:

- ATF blowing out of the transmission vent tube.


- ATF may appear cloudy or, in cases of extreme contamination, have the appearance of a strawberry milkshake.
- Visible water in the oil pan.
- A milky white substance inside the pan area.
- Spacer plate gaskets that appear to be glued to the valve body face or case.
- Spacer plate gaskets that appear to be swollen or wrinkled in areas where they are not compressed.
- Rust on internal transmission iron/steel components.

If water in the ATF has been found and the source of the water entry has not been identified, or if a leaking in-radiator transmission oil cooler is
suspected (with no evidence of cross-contamination in the coolant recovery reservoir), a simple and quick test kit is available that detects the
presence of ethylene glycol in ATF. The "Gly-Tek" test kit, available from the Nelco Company, should be obtained and the ATF tested to make an
accurate decision on the need for radiator replacement. This can help to prevent customer comebacks if the in-radiator transmission oil cooler is
leaking and reduce repair expenses by avoiding radiator replacement if the cooler is not leaking. These test kits can be obtained from:

Nelco Company

Test kits can be ordered by phone or through the website listed above. Orders are shipped standard delivery time but can be shipped on a next day
delivery basis for an extra charge. One test kit will complete 10 individual fluid sample tests. For vehicles repaired under warranty, the cost of the
complete test kit plus shipping charges should be divided by 10 and submitted on the warranty claim as a net item.

The transmission should be repaired or replaced based on the normal cost comparison procedure.

Important
If water or coolant is found in the transmission, the following components MUST be replaced.
- Replace all of the rubber-type seals.
- Replace all of the composition-faced clutch plates and/or bands.
- Replace all of the nylon parts.
- Replace the torque converter.
- Thoroughly clean and rebuild the transmission, using new gaskets and oil filter.

Important
The following steps must be completed when repairing or replacing.
- Flush and flow check the transmission oil cooler using J 45096. Refer to Corporate Bulletin Number 02-07-30-052F- Automatic
Transmission Oil Cooler Flush and Flow Test Essential Tool J 45096 TransFlow.
- Thoroughly inspect the engine cooling system and hoses and clean/repair as necessary.

Disclaimer

Technical Service Bulletin # 10-08-98-002 Date: 100806

Body - Drilling High Strength Steel Using CryoCobalt(R)


INFORMATION

Bulletin No.: 10-08-98-002

Date: August 06, 2010

Subject: Information on Drilling High Strength Steel Related to Collision Repair

Models:

2011 and Prior GM Passenger Cars and Light Duty Trucks


2010 and Prior HUMMER H2
2009 and Prior HUMMER H3
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 660
Chevrolet Venture V6-3.4L VIN E 2985
2010 and Prior Saturn Models
2009 and Prior Saab 9-7X

To improve safety, fuel economy and vehicle performance, a number of high strength steels are used in manufacturing General Motors vehicles.
These various high strength steels and their location in specific vehicles can be found in Service Information | Body Repair | Collision Repair |
Visual Identification.

To perform structural or collision damage repairs, it is often necessary to drill out (remove) resistance spot welds in order to separate the
components being serviced from the vehicle structure.

A variety of drill bits are available to remove these resistance spot welds, however the useful life of many of these drills is limited by the hardness
of the high strength steels.

The General Motors Collision Repair Technology Center has recently validated a *CryoCobalt(TM) drill bit that has been developed for use with
very hard metals. These drill bits performed with exceptional results and should allow for increased production and reduced overall cost related to
resistance spot weld removal. These drill bits can also be re-sharpened.

These drill bits are available directly from the manufacturer. Refer to the ordering information below.

*We believe this source and their products to be reliable. There may be additional manufacturers of such products/materials. General Motors does
not endorse, indicate any preference for, or assume any responsibility for the products or material from this firm or for any such items that may be
available from other sources.

Ordering Information

Use the part numbers listed below for special GM pricing.

Contact the drill bit manufacturer, Partsmaster.

Disclaimer
Technical Service Bulletin # 00-08-48-005D Date: 100910

Body - Vehicle Glass Distortion Information


INFORMATION

Bulletin No.: 00-08-48-005D

Date: September 10, 2010

Subject: Distortion in Outer Surface of Vehicle Glass

Models:

2011 and Prior GM Passenger Cars and Trucks


2009 and Prior HUMMER H2
2010 and Prior HUMMER H3
2005-2009 Saab 9-7X
2010 and Prior Saturn

Supercede:
This bulletin is being revised to add model years. Please discard Corporate Bulletin Number 00-08-48-005C (Section 08 - Body and Accessories).
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 661
Chevrolet Venture V6-3.4L VIN E 2986

Distortion in the outer surface of the windshield glass, door glass or backlite glass may appear after the vehicle has:

- Accumulated some mileage.


- Been frequently washed in automatic car washes, particularly "touchless" car washes.

This distortion may look like a subtle orange peel pattern, or may look like a drip or sag etched into the surface of the glass.

Some car wash solutions contain a buffered solution of hydrofluoric acid which is used to clean the glass. This should not cause a problem if used
in the correct concentration. However, if not used correctly, hydrofluoric acid will attack the glass, and over time, will cause visual distortion in the
outer surface of the glass which cannot be removed by scraping or polishing.

If this condition is suspected, look at the area of the windshield under the wipers or below the belt seal on the side glass. The area of the glass
below the wipers or belt seal will not be affected and what looks like a drip or sag may be apparent at the edge of the wiper or belt seal. You may
also see a line on the glass where the wiper blade or the belt seal contacts the glass.

Important
The repair will require replacing the affected glass and is not a result of a defect in material or workmanship. Therefore, is not covered by
New Vehicle Warranty.

Disclaimer

Technical Service Bulletin # 10-08-45-001B Date: 101025

Electrical - Information For Electrical Ground Repair


INFORMATION

Bulletin No.: 10-08-45-001B

Date: October 25, 2010

Subject: Information for Electrical Ground Repair - Use New Replacement Fasteners with Conductive Finish

Models:

2011 and Prior GM Passenger Cars and Trucks (including Saturn)


2010 and Prior HUMMER H2, H3
2009 and Prior Saab 9-7X

Supercede:
This bulletin is being revised to add the 2011 model year and update the Warranty Information. Please discard Corporate Bulletin Number
10-08-45-001A (Section 08 - Body and Accessories).

Electrical Ground Repair Overview

Proper electrical system function relies on secure, stable and corrosion-free electrical ground connections. Loose, stripped, or corroded connections
increase the possibility of improper system function and loss of module communication. These conditions may also lead to unnecessary repairs and
component replacement.

In general, electrical ground connections are accomplished using one, or a combination of the following attachment methods:

- Welded M6 stud and nut


- Welded M6 nut and bolt
- Welded M8 nut and bolt

Determine which attachment method is used and perform the appropriate or alternative repair as described in this bulletin.

M6 Weld Stud Replacement

Caution

Use only the GM-approved replacement fasteners with conductive finish for electrical ground repair.
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 662
Chevrolet Venture V6-3.4L VIN E 2987

1. Select a location adjacent the damaged or missing M6 ground stud having 20 mm (0.79 in) clearance behind the panel surface and 20 mm
(0.79 in) clearance surrounding the M6 conductive rivet stud flange.
2. Using GM approved residue-free solvent or equivalent, remove any grease from the repair site and allow to dry.

Note
Ensure 20 mm (0.79 in) clearance is maintained behind the panel to be drilled.

3. Drill a 10 mm (0.40 in) diameter hole through the panel.

4. Remove paint and primer from the area surrounding the 10 mm (0.40 in) hole until bare metal is visible.

Important
The M6 conductive rivet stud as shown, can accommodate a panel thickness range of 0.7-4.2 mm (0.03-0.17 in). If there are layers of
sheet metal, they should be touching without any air gaps to ensure a good ground.

5. Select a M6 conductive rivet stud. Refer to the Parts Information section of this bulletin.

Note
Use the GE-50317 rivet stud tool kit.

6. Place the M6 conductive rivet stud (1) in the 10 mm (0.40 in) hole. Assemble the rivet stud tool (2) with the groove and flare side facing the
rivet stud, then the washer and the M6 nut (3).
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 663
Chevrolet Venture V6-3.4L VIN E 2988

7. Using a wrench on the rivet stud tool, and a socket on the M6 nut, secure the M6 conductive rivet stud.
8. Ensure the rivet stud is securely fastened, WITHOUT ANY detectable movement.
9. Completely wrap the threads of the rivet stud with painters tape or equivalent.

Note
The rivet stud and surrounding panel area MUST BE properly refinished PRIOR to the installation of the ground wire terminal and
conductive nut to maintain a secure, stable and corrosion-free electrical ground.

10. Refinish the repair area using an anti-corrosion primer. Refer to Anti-Corrosion Treatment and Repair in SI.
11. Allow the refinished repair area to cure sufficiently before removing the protective material applied to the rivet stud threads.
12. Remove the painters tape or equivalent from the rivet stud threads.
13. Using GM approved residue-free solvent or equivalent, thoroughly clean the rivet stud threads to remove any adhesive and allow to dry.
14. Using a small brush, apply Dielectric Lubricant GM P/N 12377900 (Canadian P/N 10953529) to the threads of the M6 conductive rivet stud.

Note
Fretting corrosion is a build-up of insulating, oxidized wear debris that can form when there is a small motion between electrical contacts.
The oxidized wear debris can accumulate at the electrical contact points causing the electrical resistance across the connection to increase.

15. Carefully remove ANY corrosion or contamination that may be present on the electrical ground wire terminal.
16. Install the electrical ground wire terminal to the rivet stud.
17. Select a M6 conductive nut. Refer to the Parts Information section of this bulletin.
18. Install the M6 conductive nut to the rivet stud and:

Tighten
Tighten to 8 Nm (71 lb in).

19. Verify proper system operation.

M6 Weld Nut

Caution

Use only the GM-approved replacement fasteners with conductive finish for electrical ground repair.

1. If the M6 weld nut at the electrical ground location is damaged or stripped, a M7 conductive self-threading bolt may be used to secure the
ground wire terminal.
2. Using GM approved residue-free solvent or equivalent, remove any grease from the surface surrounding the weld nut and allow to dry.
3. Remove any loose metal particles from the damaged or stripped weld nut with a stiff brush.
4. Select a M7 conductive self-threading bolt. Refer to the Parts Information section of this bulletin
5. Using a small brush, apply Dielectric Lubricant GM P/N 12377900 (Canadian P/N 10953529) to the threads of the M7 conductive
self-threading bolt.

Note
Fretting corrosion is a build-up of insulating, oxidized wear debris that can form when there is a small motion between electrical contacts.
The oxidized wear debris can accumulate at the electrical contact points causing the electrical resistance across the connection to increase.

6. Carefully remove ANY corrosion or contamination that may be present on the electrical ground wire terminal.
7. Install the electrical ground wire terminal to the M7 conductive self-threading bolt.
8. Install the M7 conductive self-threading bolt and:

Tighten
Tighten to 9 Nm (80 lb in).

9. Verify proper system operation.

M6 Weld Nut Alternative Repair

Caution
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 664
Chevrolet Venture V6-3.4L VIN E 2989

Use only the GM-approved replacement fasteners with conductive finish for electrical ground repair.

1. If the electrical ground location is accessible from both sides of the panel, a M6 conductive bolt and a M6 conductive nut may be used to
secure the electrical ground wire terminal. Refer to the Parts Information section of this bulletin.
2. Select a location adjacent the damaged M6 weld nut having 20 mm (0.79 in) clearance behind the panel surface and 20 mm (0.79 in)
clearance surrounding the new electrical ground site.
3. Using GM approved residue-free solvent or equivalent, remove any grease from the surface surrounding the ground location and allow to
dry.

Note
Ensure 20 mm (0.79 in) clearance is maintained behind the panel to be drilled.

4. Drill a 8.5 mm (0.33 in) diameter hole through the panel.


5. Remove paint and primer from the area surrounding the 8.5 mm (0.33 in) hole until bare metal is visible.
6. Select a M6 conductive bolt. Refer to the Parts Information section of this bulletin.
7. Using a small brush, apply Dielectric Lubricant GM P/N 12377900 (Canadian P/N 10953529) to the threads of the M6 conductive bolt.

Note
Fretting corrosion is a build-up of insulating, oxidized wear debris that can form when there is a small motion between electrical contacts.
The oxidized wear debris can accumulate at the electrical contact points causing the electrical resistance across the connection to increase.

8. Carefully remove ANY corrosion or contamination that may be present on the electrical ground wire terminal.
9. Install the electrical ground wire terminal and the M6 conductive bolt to the ground location.
10. Select a M6 conductive nut. Refer to the Parts Information section of this bulletin.
11. Install the M6 conductive nut to the bolt and:

Tighten
Tighten to 8 Nm (71 lb in).

Note
The repair area MUST BE properly refinished to maintain a secure, stable and corrosion-free electrical ground.

12. Refinish the repair area using an anti-corrosion primer. Refer to Anti-Corrosion Treatment and Repair in SI.
13. Verify proper system operation.

M8 Weld Nut

Caution

Use only the GM-approved replacement fasteners with conductive finish for electrical ground repair.

1. If the M8 weld nut electrical ground location is accessible from both sides of the panel, a M8 conductive bolt and a M8 conductive nut may
be used to secure the electrical ground wire terminal. Refer to the Parts Information section of this bulletin.
2. Select a location adjacent the M8 weld nut having 20 mm (0.79 in) clearance behind the panel surface and 20 mm (0.79 in) clearance
surrounding the new electrical ground site.
3. Using GM approved residue-free solvent or equivalent, remove any grease from the surface surrounding the ground location and allow to
dry.

Note
Ensure 20 mm (0.79 in) clearance is maintained behind the panel to be drilled.

4. Drill a 10 mm (0.40 in) diameter hole through the panel.


5. Remove paint and primer from the area surrounding the 10 mm (0.40 in) hole until bare metal is visible.
6. Select a M8 conductive bolt. Refer to the Parts Information section of this bulletin.
7. Using a small brush, apply Dielectric Lubricant GM P/N 12377900 (Canadian P/N 10953529) to the threads of the M8 conductive bolt.

Note
Fretting corrosion is a build-up of insulating, oxidized wear debris that can form when there is a small motion between electrical contacts.
The oxidized wear debris can accumulate at the electrical contact points causing the electrical resistance across the connection to increase.

8. Carefully remove ANY corrosion or contamination that may be present on the electrical ground wire terminal.
9. Install the electrical ground wire terminal and the M8 conductive bolt to the ground location.
10. Select a M8 conductive nut. Refer to the Parts Information section of this bulletin.
11. Install the M8 conductive nut to the bolt and:

Tighten
Tighten to 22 Nm (16 lb ft).

Note
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 665
Chevrolet Venture V6-3.4L VIN E 2990
The repair area MUST BE properly refinished to maintain a secure, stable and corrosion-free electrical ground.

12. Refinish the repair area using an anti-corrosion primer. Refer to Anti-Corrosion Treatment and Repair in SI.
13. Verify proper system operation.

M8 Weld Nut Alternative Repair

Caution

Use only the GM-approved replacement fasteners with conductive finish for electrical ground repair.

1. If the M8 weld nut electrical ground location is not accessible from both sides of the panel, a M6 conductive rivet stud and a M6 conductive
nut may be used to secure the electrical ground wire terminal.
2. Select a location adjacent the damaged M8 weld nut having 20 mm (0.79 in) clearance behind the panel surface and 20 mm (0.79 in)
clearance surrounding the M6 conductive rivet stud flange.
3. Using GM approved residue-free solvent or equivalent, remove any grease from the repair site and allow to dry.

Note
Ensure 20 mm (0.79 in) clearance is maintained behind the panel to be drilled.

4. Drill a 10 mm (0.40 in) diameter hole through the panel.

5. Remove paint and primer from the area surrounding the 10 mm (0.40 in) until bare metal is visible.

Important
The M6 conductive rivet stud as shown, can accommodate a panel thickness range of 0.7-4.2 mm (0.03-0.17 in). If there are layers of
sheet metal, they should be touching without any air gaps to ensure a good ground.

6. Select a M6 conductive rivet stud. Refer to the Parts Information section of this bulletin.

Note
Use the GE-50317 rivet stud tool kit.

7. Place the M6 conductive rivet stud (1) in the 10 mm (0.40 in) hole. Assemble the rivet stud tool (2) with the groove and flare side facing the
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 666
Chevrolet Venture V6-3.4L VIN E 2991
rivet stud, then the washer and the M6 nut (3).

8. Using a wrench on the rivet stud tool, and a socket on the M6 nut, secure the M6 conductive rivet stud.
9. Ensure the new rivet stud is securely fastened, WITHOUT ANY detectable movement.
10. Completely wrap the threads of the rivet stud with painters tape or equivalent.

Note
The rivet stud and surrounding panel area MUST BE properly refinished PRIOR to the installation of the electrical ground wire terminal
and conductive nut to maintain a secure, stable and corrosion-free electrical ground.

11. Refinish the repair area using an anti-corrosion primer. Refer to Anti-Corrosion Treatment and Repair in SI.
12. Allow the refinished repair area to cure sufficiently before removing the protective material applied to the rivet stud threads.
13. Remove the painters tape or equivalent from the rivet stud threads.
14. Using GM approved residue-free solvent or equivalent, thoroughly clean the rivet stud threads to remove any adhesive and allow to dry.
15. Using a small brush, apply Dielectric Lubricant GM P/N 12377900 (Canadian P/N 10953529) to the threads of the M6 conductive rivet stud.

Note
Fretting corrosion is a build-up of insulating, oxidized wear debris that can form when there is a small motion between electrical contacts.
The oxidized wear debris can accumulate at the electrical contact points causing the electrical resistance across the connection to increase.

16. Carefully remove ANY corrosion or contamination that may be present on the electrical ground wire terminal.
17. Install the electrical ground wire terminal to the M6 conductive rivet stud.
18. Select a M6 conductive nut. Refer to the Parts Information section of this bulletin.
19. Install the M6 conductive nut to the rivet stud and:

Tighten
Tighten to 8 Nm (71 lb in)

20. Verify proper system operation.

Parts Information

Warranty Information (excluding Saab Models)

For vehicles repaired under warranty, use:


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 667
Chevrolet Venture V6-3.4L VIN E 2992

Warranty Information (Saab Models)

For vehicles repaired under warranty, use the table.

Disclaimer

Technical Service Bulletin # 05-06-04-022G Date: 101027

Fuel System - TOP TIER Detergent Gasoline (Canada)


INFORMATION

Bulletin No.: 05-06-04-022G

Date: October 27, 2010

Subject: TOP TIER Detergent Gasoline Information and Available Brands (Deposits, Fuel Economy, No Start, Power, Performance, Stall
Concerns) - Canada ONLY

Models:

2011 and Prior GM Passenger Cars and Trucks (Canada Only)

Supercede:
This bulletin is being revised to update the model years and include an additional gasoline brand as a TOP TIER source. Please discard Corporate
Bulletin Number 05-06-04-022F (Section 06 - Engine/Propulsion System). In the U.S., refer to the latest version of Corporate Bulletin Number
04-06-04-047I.

A new class of fuel called TOP TIER Detergent Gasoline is appearing at retail stations of some fuel marketers. This gasoline meets detergency
standards developed by six automotive companies. All vehicles will benefit from using TOP TIER Detergent Gasoline over gasoline containing the
"Lowest Additive Concentration" recommended by the Canadian General Standards Board (CGSB). Those vehicles that have experienced deposit
related concerns may especially benefit from use of TOP TIER Detergent Gasoline.
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 668
Chevrolet Venture V6-3.4L VIN E 2993

Intake valve: 16,093 km (10,000 mi) with TOP TIER Detergent Gasoline

Intake valve: 16,093 km (10,000 mi) with Minimum Additive recommended by the CGSB

Top Tier Fuel Availability

Chevron was the first to offer TOP TIER Detergent Gasoline in Canada. Shell became the first national gasoline retailer to offer TOP TIER
Detergent Gasoline across Canada. Petro-Canada began offering TOP TIER Detergent Gasoline nationally as of October 1, 2006. Sunoco began
offering TOP TIER Detergent Gasoline in March of 2007. Esso began offering TOP TIER Detergent Gasoline in May of 2010.

Gasoline Brands That Currently Meet TOP TIER Detergent Gasoline Standards

The following gasoline brands meet the TOP TIER Detergent Gasoline Standards in all octane grades :

- Chevron Canada (markets in British Columbia and western Alberta)


- Shell Canada (nationally)
- Petro-Canada (nationally)
- Sunoco-Canada (Ontario)
- Esso-Canada (nationally)

What is TOP TIER Detergent Gasoline?

TOP TIER Detergent Gasoline is a new class of gasoline with enhanced detergency and no metallic additives. It meets new, voluntary deposit
control standards developed by six automotive companies that exceed the detergent recommendations of Canadian standards and does not contain
metallic additives, which can damage vehicle emission control components.

Where Can TOP TIER Detergent Gasoline Be Purchased?

The TOP TIER program began in the U.S. and Canada on May 3, 2004. Some fuel marketers have already joined and introduced TOP TIER
Detergent Gasoline. This is a voluntary program and not all fuel marketers will offer this product. Once fuel marketers make public announcements,
they will appear on a list of brands that meet the TOP TIER standards.

Who developed TOP TIER Detergent Gasoline standards?


2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 669
Chevrolet Venture V6-3.4L VIN E 2994

TOP TIER Detergent Gasoline standards were developed by six automotive companies: BMW, General Motors, Honda, Toyota, Volkswagen and
Audi.

Why was TOP TIER Detergent Gasoline developed?

TOP TIER Detergent Gasoline was developed to increase the level of detergent additive in gasoline. In the U.S., government regulations require
that all gasoline sold in the U.S. contain a detergent additive. However, the requirement is minimal and in many cases, is not sufficient to keep
engines clean. In Canada, gasoline standards recommend adherence to U.S. detergency requirements but do not require it. In fact, many brands of
gasoline in Canada do not contain any detergent additive. In order to meet TOP TIER Detergent Gasoline standards, a higher level of detergent is
needed than what is required or recommended, and no metallic additives are allowed. Also, TOP TIER was developed to give fuel marketers the
opportunity to differentiate their product.

Why did the six automotive companies join together to develop TOP TIER?

All six corporations recognized the benefits to both the vehicle and the consumer. Also, joining together emphasized that low detergency and the
intentional addition of metallic additives is an issue of concern to several automotive companies.

What are the benefits of TOP TIER Detergent Gasoline?

TOP TIER Detergent Gasoline will help keep engines cleaner than gasoline containing the "Lowest Additive Concentration" recommended by
Canadian standards. Clean engines help provide optimal fuel economy and engine performance, and also provide reduced emissions. Also, the use
of TOP TIER Detergent Gasoline will help reduce deposit related concerns.

Who should use TOP TIER Detergent Gasoline?

All vehicles will benefit from using TOP TIER Detergent Gasoline over gasoline containing the "Lowest Additive Concentration" recommended by
Canadian standards. Those vehicles that have experienced deposit related concerns may especially benefit from use of TOP TIER Detergent
Gasoline. More information on TOP TIER Detergent Gasoline can be found at this website, http://www.toptiergas.com/.

Disclaimer

Technical Service Bulletin # 10-08-44-006 Date: 101011

Navigation - Report Missing/Inaccurate Nav. Map Info


INFORMATION

Bulletin No.: 10-08-44-006

Date: October 11, 2010

Subject: Reporting Missing or Inaccurate Navigation Radio Map Disc Information - Complete and Submit Feedback Form at GM Navigation Disc
Center Website

Models:

2011 and Prior GM Passenger Cars and Trucks


Equipped with Navigation Radio

Some customers may notice that some navigation radio map discs may have missing or incorrect information.

The following list contains some examples:

- Missing or incorrect roads, road names or road shapes


- Missing or incorrect addresses
- Missing or incorrect highway labeling
- Missing or incorrect highway exit numbers
- Missing or incorrect traffic restrictions
- Missing points of interest (POI) or incorrect details, such as location, category or phone number

General Motors uses a map database from two different suppliers. The two map suppliers are consistently updating their map database and will
gladly accept any input regarding missing or incorrect information on the navigation radio map disc.
2000 Chevy Truck Venture V6-3.4L VIN E Copyright © 2011, ALLDATA 10.40 Page 670
Chevrolet Venture V6-3.4L VIN E 2995

To report any missing or incorrect information, please access the GM Navigation Disc Center at the following web site:
http://www.gmnavdisc.com.

At the GM Navigation Disc Center home page, select the tab: Your Feedback.
In the Navigation Data Feedback form, fill in the appropriate information as required and then select: Submit, to send the form.

Disclaimer

You might also like