Professional Documents
Culture Documents
Marks: 1
It is the narrow surface along the groove that determines the size of the drill and keeps the drill
aligned.
Choose one answer.
a. web
b. dead center
c. point
d. margin
Question 2
Marks: 1
It is the flattened end of the paper shank that helps drive the drill and provides means for driving
the drill from the socket without injuring the shank.
Choose one answer.
a. tang
b. flute
c. margin
d. lips
Question 3
Marks: 1
This refers to the resistance from penetration or withstand abrasions and wears.
Choose one answer.
a. Hardness
b. Elasticity
c. Plasticity
d. Brittleness
Question 4
Marks: 1
This is the hardening agent which has the greatest influence on the quality of the steel in terms of
wear resistance and hardenability.
Choose one answer.
a. Carbon
b. Calcium
c. Silicon
d. Anti-corrosion
Question 5
Marks: 1
It permits the operator to engage or disengage the feed without removing his hand from the lever
that controls the advance and return of the spindle.
Choose one answer.
a. feed-change gear case
b. feed-change lever
c. feed clutch
b. margin
c. flute
d. dead center
Question 7
Marks: 1
It is used for shaping one end of the hole to fit screws, rivets or bolts
Choose one answer.
a. Reverse facing
b. Counter sinking
c. Counter boring
d. Spot facing
Question 8
Marks: 1
It is used for producing holes up to 20 mm and very convenient in any drilling position
Choose one answer.
a. Bench Press
b. Impact Drill
c. Base
d. Hand Drill
Question 9
Marks: 1
Drill clearance of aluminum, soft and medium steels.
Choose one answer.
a. 12º
b. 12º to 15º
c. 15º
d. 7º to 12º
Question 10
Marks: 1
A kind of cutting tool used in producing initial circle or circular hole
Choose one answer.
a. Hand Taps
b. Twist Drill
c. Boring Tool
d. Reamers
Question 11
Marks: 1
It houses the feed mechanism of a drill press.
Choose one answer.
a. feed-change gear case
b. feed-change lever
b. Plasticity
c. Elasticity
d. Brittleness
Question 13
Marks: 1
A part of a drill press which is used to control the feed.
Choose one answer.
a. feed hand wheel
b. feed-change lever
c. feed shaft
d. feed clutch
Question 14
Marks: 1
A larger and heavier type of drill presses which required more mechanisms and accessories for
various degree of drilling operation
Choose one answer.
a. Heavy Duty Drilling Machine
b. Floor Model
c. Upright Model
b. body
c. flute
d. tang
Question 16
Marks: 1
It permits to clamp the work without the use of long clamping bolts.
Choose one answer.
a. Goose neck clamp
b. Shaper machine
c. Lathe machine
d. Drilling machine
Question 19
Marks: 1
Average cutting speed with drill of brass and copper.
Choose one answer.
a. 100 ft. per min
b. Spot facing
c. Reverse facing
d. Counter boring
Question 21
Marks: 1
Another method of forming internal threads on cylindrical hole
Choose one answer.
a. Taping
b. Twisting
c. Reaming
d. Boring
Question 22
Marks: 1
This part of drilling machine that guides the working table in its rotation and its a upward and
downward movement
Choose one answer.
a. Table
b. Chuck
c. Base
d. Column
Question 23
Marks: 1
It is the process of squaring top of the hole into a surface finish for fitting a nut or head of a cap
screw
Choose one answer.
a. Reverse facing
b. Counter bore
c. Counter sink
d. Spot facing
Question 24
Marks: 1
Drill clearance of brass.
Choose one answer.
a. 15º
b. 12º
c. 7º to 12º
d. 12º to 15º
Question 25
Marks: 1
It provides a steady foundation for the column and table also serves as a reservoir for the cutting
lubricant when used.
Choose one answer.
a. spindle
b. base
c. feed shaft
d. chuck
Question 26
Marks: 1
Is the part of the drill that fits into the holding device.
Choose one answer.
a. point
b. tang
c. body
d. shank
Question 27
Marks: 1
It is the process of enlarging a previously made hole
Choose one answer.
a. Hand Tap
b. Boring
c. Reamer
d. Twist
Question 28
Marks: 1
Drill clearance of hard steel.
Choose one answer.
a. 12º to 15º
b. 12º
c. 7º to 12º
d. 15º
Question 29
Marks: 1
It is a round or rectangular cast iron designed to support the workpiece to be machined.
Choose one answer.
a. drill head
b. spindle
c. base
d. working table
Question 30
Marks: 1
This maybe added to low-carbon steel to improve machinability by removing blue holes and
decreasing shrinkage in the steel.
Choose one answer.
a. Silicon
b. Carbon
c. Manganese
b. Nitrogen
c. Silicon
d. Sulfur
Question 32
Marks: 1
The property of metal that could be stretched with a tensional force.
Choose one answer.
a. Ductility
b. Elasticity
c. Brittleness
d. Malleability
Question 33
Marks: 1
It is the conical part of the drill.
Choose one answer.
a. shank
b. point
c. tang
d. lips
Question 34
Marks: 1
A lever that is used to change dial setting position.
Choose one answer.
a. head adjusting shaft
c. feed-change lever
b. working table
c. cutting tool
b. lips
c. tip
d. point
Question 37
Marks: 1
Average cutting speed with drill of an aluminum.
Choose one answer.
a. 50 ft. per min
b. Elasticity
c. Toughness
d. Hardness
Question 40
Marks: 1
One of the process in metallurgy is alteration of the structure of the metal or alloy by heating to
definite temperatures and cooling at various rates is called _______.
Choose one answer.
a. Annealing
b. Heat treatment
c. Quenching
d. Hardening
Question 41
Marks: 1
It is fixed by bolts on the bench or floor that holds and supports the drilling machine
Choose one answer.
a. Base
b. Spindle
c. Column
d. Table
Question 42
Marks: 1
The capacity of a metal to resist deformation when tensile force or pressure is applied
Choose one answer.
a. Brittleness
b. Tensile
c. Toughness
d. Strength
Question 43
Marks: 1
With its sulfur content that removes oxygen during the manufacture of steel which increases the
strength, toughness, shock resistance and ductility.
Choose one answer.
a. Manganese
b. Phosphorus
c. Carbon dioxide
d. Oxidation
Question 44
Marks: 1
A part of the drill that is fluted and relieved.
Choose one answer.
a. dead center
b. point
c. body
d. lips
Question 45
Marks: 1
Average cutting speed with drill of stainless steel and monel metal.
Choose one answer.
a. 200 ft per min
c. feed-change lever
d. speed-change lever
Question 48
Marks: 1
Part of a drill press used to move up and down to provide the desire feed.
Choose one answer.
a. column
b. drill head
c. spindle sleeve
d. chuck
Question 49
Marks: 1
It is the point at which the two (2) lips properly ground and meet.
Choose one answer.
a. tang
b. body
c. flute
d. dead center
Question 50
Marks: 1
Used to clamp the drill head to the column.
Choose one answer.
a. Head clamping screw
d. Box column
Question 51
Marks: 1
It provides larger capacity of drilling operations that enables operator to control through hand
feed pressure.
Choose one answer.
a. Impact drills
b. Hand drills
c. Sensitive drills
d. Bench/Floor Model
Question 52
Marks: 1
It is the rotating part of the drilling machine
Choose one answer.
a. Drill Head
b. Base
c. Drill Head
d. Spindle
Question 53
Marks: 1
Used to hold the drill chuck or socket.
Choose one answer.
a. Box column
b. Base
c. Spindle Sleeve
d. Feed shaft
Question 54
Marks: 1
A property of metal that measures its stiffness by either by bending stress or torsion test such as
used on materials for shaft, taps, twist drills and other tools or machine parts working in torsion.
Choose one answer.
a. Hardness
b. Strength
c. Module of elasticity
d. Toughness
Question 55
Marks: 1
Controls the speed-change gears and set the gears to the desired spindle speed.
Choose one answer.
a. Speed change lever
b. Table
c. Chuck
d. Spindle
Question 58
Marks: 1
A property of metal that allows to be deformed to certain extent without fracture
Choose one answer.
a. Strength
b. Hardness
c. Plasticity
d. Machinability
Question 59
Marks: 1
This is used for sizing and finishing a hole for fitness with certain accuracy of work is needed
Choose one answer.
a. Twist
b. Hand Tap
c. Boring
d. Reamer
Question 60
Marks: 1
It carries the motor that drives the spindle which is a round shaft fitted with a chuck on one end
for holding the cutting tools.
Choose one answer.
a. Base
b. Spindle
c. Drill head
d. Column
Question 61
Marks: 1
It drives all the mechanism of the machine. It does not drive the cutting lubricant pump.
Choose one answer.
a. drill head
b. operator
c. driving motor
d. feed clutch
Question 63
Marks: 1
A clamp that has an adjusting screw which permits the leveling of the strap from the work to the
step block.
Choose one answer.
a. Finger single end clamp
c. spindle sleeve
d. spindle-control lever
Question 65
Marks: 1
Property of metal which permits metal to be hammered or rolled into other sizes and shapes
Choose one answer.
a. Elasticity
b. Brittleness
c. Malleability
d. Toughness