Professional Documents
Culture Documents
A61
FEMALE x FEMALE CERTIFICATIONS
Standard equipment:
Female NPT inlet and outlet, forged
brass body, brass finish ball
b with teflon seats. LISTED 36Y7
c
a/b (Orifice - K factor) c (plug) PORT A B C D H
SPECIFY THREAD 1-1/4” (5/8”-11.2)* 1/4” 1-1/16” 5-1/32” 2-43/64” 5-11/32” 4-27/64” 1-57/64”
A61
GROOVE X GROOVE CERTIFICATIONS
Standard equipment:
GROOVE inlet and outlet, forged
b brass body, brass finish ball with
teflon seats.
FM approved at 300 psi
a
1-1/4” (3/8” - 2.8) 1/4” 1-1/16” 6-13/32” 2-43/64” 5-11/32” 4-27/64” 1-1/4”groove
C 1-1/4” (7/16” - 4.2) 1/4” 1-1/16” 6-13/32” 2-43/64” 5-11/32” 4-27/64” 1-1/4”groove
H 1-1/4” (1/2” - 5.6) 1/4” 1-1/16” 6-13/32” 2-43/64” 5-11/32” 4-27/64” 1-1/4”groove
B
D 1-1/4” (17/32” - 8) 1/4” 1-1/16” 6-13/32” 2-43/64” 5-11/32” 4-27/64” 1-1/4”groove
PORT
1-1/4” (5/8” - 11.2) 1/4” 1-1/16” 6-13/32” 2-43/64” 5-11/32” 4-27/64” 1-1/4”groove
1-1/4” (3/4” - 14) 1/4” 1-1/16” 6-13/32” 2-43/64” 5-11/32” 4-27/64” 1-1/4”groove
A
SPECIFY THREAD
42
(Technical communication n° A-
039)
Products
Thread
PORT A B C
2 5
1" (orifice 1/2) 1 7/64" 5 1/32"
45/64" 11/32"
2 5
1" (orifice 17/32") 1 7/64" 5 1/32"
45/64" 11/32"
2 5
1 1/4" (orifice 1/2") 1 7/64" 5 1/32"
45/64" 11/32"
1 1/4" (orifice 2
1 7/64" 5 1/32" 511/32"
17/32") 45/64"
The intent of this section is to require It permits both an electrically operated alarm
inspector's test connection located in a manner and a water motor alarm supplied from an alarm
which will provide for the testing of all water valve to be tested through a single test pipe.
flow alarm devices.
Pressure
VEHZ.EX4430 - Drain Fittings, Special Type http://database.ul.com/cgi-bin/XYV/template/LISEXT/1FRAME/showpag...
VEHZ.EX4430
Drain Fittings, Special Type
Page Bottom
Model A61 Test and Drain fitting, 1 in. and 1-1/4 in. NPT size simulating a 2.8, 4.2, 5.6, 8.0, 11.2 and 14.0 K-factor, for installation in threaded steel
pipe where pressures do not exceed 300 psig.
Model A61 Test and Drain fitting, 2 in. NPT size simulating a 4.2, 5.6, 8.0, 11.2, 14.0, 16.8, 22.4 and 25.2 K-factors, for installation in threaded or
grooved steel pipe where pressures do not exceed 300 psig.
This fitting is intended for installation on sprinkler systems in accordance with the Standard for Installation of Sprinkler Systems, NFPA 13.
The appearance of a company's name or product in this database does not in itself assure that products so identified have been manufactured
under UL's Follow-Up Service. Only those products bearing the UL Mark should be considered to be Listed and covered under UL's Follow-Up
Service. Always look for the Mark on the product.
UL permits the reproduction of the material contained in the Online Certification Directory subject to the following conditions: 1. The Guide
Information, Designs and/or Listings (files) must be presented in their entirety and in a non-misleading manner, without any manipulation of the data
(or drawings). 2. The statement "Reprinted from the Online Certifications Directory with permission from Underwriters Laboratories Inc." must
appear adjacent to the extracted material. In addition, the reprinted material must include a copyright notice in the following format: "Copyright ©
2010 Underwriters Laboratories Inc.®"
Model A61
Rated working
Nominal
Model Designation Size, inches NPS pressure, Remarks
K-factor(s)
psi (kPa)
A61 1 2.8, 4.2, 5.6, 8.0 300 (2070) a
Remarks:
a. Devices supplied with female NPT threaded end connections.
b. Devices supplied with grooved end connections.