Professional Documents
Culture Documents
For MPR-e and MPR-1c, if the SW version of the existing network is anterior to R5.0.0, all new or repaired MPT-MC/HC/XP received with a SW Release 5.2.0 must be downgraded to the network SW Release using MCT / TCO ≥ R5.0.0.
This MCT must be first downloaded from OLCS server to a laptop, where the downgrade can be performed.
MPT-HC-HQAM MPT-MC / MPT-HC-HQAM to MPT through power injector MPT-HC-HQAM to MSS MPT-HC-HQAM to Ethernet
MPT-MC
MPT-XP-HQAM MSS Electrical plug-in Electrical Optical device Optical
Configuration [1+0]
Coupler
1+1 or 2+0 Copolar
RPS LC-LC optical cord [1+1] MPT-HQAM to MSS
Electrical
[1+1] MPT-HQAM to MSS
Optical
MPT Powering devices
RPS cord when needed RPS cord when needed MPT to Power Injector Box - MPT-HC-HQAM with MPT
RPS LC-LC optical cord 3CC52169XXXX
Configuration [1+1]
Ortho Mode Transducer OMT Ortho Mode Transducer OMT [2+0] XPIC MPT-HQAM to MSS [2+0] XPIC MPT-HQAM to MSS MPT-HQAM with MPT MPT-HQAM with MPT
Configuration [2+0] XPIC
6, 7,8 and 10,5 / 11 GHz 11 to 23 GHz Electrical Optical Extended Power Unit-Electrical Extended Power Unit – Optical
MPT1 pol V MPT1 pol V
MPT2 pol H MPT2 pol H
Pigtail
RJ45/N
CAT5e cable
data and DC
Pigtail RJ45/N 1AC015760006
XPIC cord XPIC cord − 48 V or
CAT5e cable RJ45 to any Fiber
Coaxial +24 V DC
data and DC switch or router Coaxial
Fiber
1AC015760006
− 48 V or
MSS-1/4/8 MSS-1/4/8
+24 V DC
Note: See the applicable MPR user manual Max 2 MPT Max 2 MPT
Note: See the applicable MPR user manual
for other supported configurations. for other supported configurations. Extended Power unit 3CC50174XXXX Extended Power unit 3CC50174XXXX
9500 MPR Quick Start Guide MPT-HC-HQAM / XP-HQAM / MC Installation Steps
Install MPT [1+0] on Install coupler for
1 Install MSS unit 2 Install MPT [1+0] on
non integrated antenna
3 integrated antenna
4 Set MPT polarization 5 MPT [1+1] 6 Install MPT [2+0] with OMT
Note: MPT toolbox is mandatory 3CC50098AAXX 5.1 Set the coupler polarization (antenna side) to 6.1 Follow the same process described in steps 3.1
1.1 Install the MSS indoor unit in one of four 2.1 Assemble & install the non-integrated Factory delivery is in V polarization.
antenna. (Refer to antenna instructions) 3.1 Assemble & Install the Integrated antenna . match the antenna polarization (same process as and 3.3 . Set the OMT then connect to the antenna.
supported configurations To change the polarization, loosen the two steps 3.1 to 3.3)
(see the applicable user manual): (Refer to antenna instructions)
2.2 Verify the polarization on the antenna and screws and line up the H or V polarization with WARNING: Verify that the indication engraved 6.2 Set the appropriate polarization on the MPT (see
change it if required 3.2 Verify the polarization on the antenna and the polarization references. on the coupler is directed toward the pole side. step 4); the connectors must face down.
- ETSI rack (21 in.) change it if required
-Standard rack (19 in.) 6.3 Open the four locking hooks on the MPT and slide
- wall mount 3.3 Put silicon grease only if required in the the MPT on the OMT nose adapter.
- Full outdoor, with MSS-O . Refer to dedicated installation instructions of the antenna, see below
6.4 Secure the MPT with the four hooks.
quick start guide
Example :
H
1.2 Ground the MSS using the ground screw on Reference 11 to 38 GHz
H
the front panel of the bracket on the right side of 2.3 Assemble & install the pole mounting for polarization
H
coupler
the MSS; use grounding kit 3CC13423AAXX. remote ODU
1.3 Connect the power supply cable between the 2.4 Put silicon grease on nose o-ring only if 5.2 Install and set MPT polarization, for high
MSS and breakers or power panel: required in the installation instructions. frequency, turn the MPT polarization disk to be
H
– MSS1 and power injector box: 2x1 mm² 2.5 Set the appropriate polarization on the MPT 3.4 Set the appropriate polarization on the MPT aligned with the coupler waveguide. The connectors
1AC007800068 (see step 4); the connectors must face down. (see step 4); the connectors must face down. must face down.
– MSS4/8: 2x4 mm² 3DB18271AAXX WARNING: To avoid equipment damage, do not
– MSS8 (full config): 2x6 mm² 3CC52190AAXX 2.6 Open the four locking hooks on the MPT and 3.5 Open the four locking hooks on the MPT and 5.3 for low frequency, turn the whole MPT
slide the MPT on the remote nose adapter. slide the MPT on the antenna nose adapter. remove the waterproof tape that is glued on the
1.4 Install the integrated DDF; (see the applicable MPT waveguide. 5.4 Secure the module with the four hooks on the
manual 75 Ω, 120 Ω, RJ45). 2.7 Secure the MPT with the four hooks. 3.6 Secure the MPT with the four hooks. corresponding brackets.
7 Ground the MPT Example MPT-HQAM installation with MSS 8 Assemble and connect electrical connectors
For an explanation, see the step
Note: This is a guideline for assembling the R2CT with the RJ45 connector for CAT5e cable. For details
Connect the MPT grounding connector to the nearest grounding plate, using the ground cable 4 6.2 6.1 11.1 indicated by the numbered circle. see Best practice and tips MPR R2CT and RJ45 connector and grounding 3FQ 24013 1100 PCZZA.
16mm² 3CC08166AAXX. Washer, screw and lug are provided with the MPT.
RPS cord when needed 8.1 Prepare the R2CT connector, insert the CAT5e cable, and insert the RJ45 plug unlocking clip.
– Kit for Ethernet cable or coaxial cable (Ø 6,85) 1AD040130004
– Kit for coaxial cable (Ø 10,3) 1AB128500002
R2CT connector Assembled R2CT
1AB150990002 connector
7 11.3
8.2 Mount the RJ45 connector using the RJ45 hirose tool.
RJ45
connector