You are on page 1of 278

Comau Robotics

Instruction Handbook

Controller Unit

MOTION PROGRAMMING
System Software Rel. 1.18.015

Robot movements in programming mode, motion control, optional features (synchronous


motion, cooperative motion, sensor tracking, conveyor tracking, weaving, path governor,
smartmove, soft servo, kinematic compensation, collision detection), moving through
singularities, positioners and portals, TO_SET program, Interference Regions.

CR00757608_it-10/2013.07
The information contained in this manual is the property of COMAU S.p.A.

Reproduction of text and illustrations is not permitted without prior written approval by COMAU S.p.A.

COMAU S.p.A. reserves the right to alter product specifications at any time without notice or obligation.

Copyright © 2008-2013 by COMAU - Date of publication 07/2013


Summary

SUMMARY

PREFACE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12
Symbols used in the manual . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Reference documents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Modification History . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

1. GENERAL SAFETY PRECAUTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ...16


Responsibilities . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Safety Precautions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Purpose . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Definitions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Applicability . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Operating Modes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Performance. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25

2. SYSTEM OPERATING MODES AND STATES . . . . . . . . . . . . . . . . . . . . . . . . . . . . ...26


Foreword . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
System operating modes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
System states . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
HOLD status. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
AUTO status. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
PROGR status . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
ALARM status . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
Stand-by function . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30

3. TURN-SET AND CALIBRATION - BASIC CONCEPTS . . . . . . . . . . . . . . . . . . . . . . ...31


Foreword . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
Terminology . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
Turn-set . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
Turn-set on system calibration position . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
Turn-set on user calibration position . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
Turn-set for robot axes with multi-turn stroke. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
Calibration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
System calibration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
User calibration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34

4. ROBOT MOTION IN PROGRAMMING MODE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ...36


Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36

lb-rc-c5e-motion_enTOC.fm
3
Summary

Reference frames . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
System reference frames. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
Manual motion . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
Manual motion in WRIST_JNT mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39
Manual motion of a single arm system . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39
Manual motion of auxiliary axes, slides and rotating columns . . . . . . . . . . . . . . . . . . . . . . . . . . 39
Manual motion with Controller multi-arm configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40
Motion instruction in programming status . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40

5. MOTION CONTROL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ..43


Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43
Frames of Reference . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43
System Frame of Reference . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44
Base System of Reference definition . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45
Flange Tooling definition . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45
TCP Offset definition . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .46
Calculating the Rotation Angles . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .47
FIRST METHOD . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .47
SECOND METHOD . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .49
User System of Reference definition . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .49
Trajectory . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50
Joint Interpolation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50
Linear Interpolation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50
Circular Interpolation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51
Orientation Evolution during Linear or Circular movements. . . . . . . . . . . . . . . . . . . . . . . . . . 51
Attitude Flags During Linear and Circular Movements. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52
Turn Flag and minimum path . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52
Position Checking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53
On Trajectory Function. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53
On Position (ON POS) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54
Example of On Pos and On Trajectory. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .55
Speed Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56
Speed Overrides . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56
Cartesian Speed Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57
Cartesian Speed Control Options. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .58
Run-Time modifying the Linear Speed Override . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .59
Joint Speed Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60
Manual Motion Speed Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60
Acceleration and Deceleration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61
Acceleration/Deceleration Overrides . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 62
Joint Interpolation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 63
Cartesian Interpolation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 63
Manual Motions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 64
Motion termination . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 64
COARSE and FINE Termination . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 64

lb-rc-c5e-motion_enTOC.fm
4
Summary

JNT_COARSE and JNT_FINE Termination. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 65


NOSETTLE Termination . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 65
Trajectory Recovery. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 65
Recovery Strategy . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 65
Pending Motion Status . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .66
Recovery Range. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .66
Recovery procedure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .66
Process Resume . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 67
Automatic Process Resume. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 69
Continuous Motion . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 70
Trajectory Shape During Continuous Motion . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 71
Continuous Motion Modes (FLY) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 71
FLY_NORM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .71
FLY_CART (Controller Aided Resolved Trajectory) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .72
Dynamic Machine Stress Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .72
Constant Speed Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .73
Control of Trajectory During FLY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .73
Debug of Fly Motions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .75
Variables used with FLY Motion . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .76
Remote Tool System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 77
Integrated Movement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 78
Integrated Axis . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 79
Jogging . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .79
Reference Systems . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .79
Restrictions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .80
Palletizing functionality (optional feature) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 80
Enabling . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 81
Disabling . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 82
Example of a Palletizing Program . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 82

6. SYNCHRONOUS MOTION (OPTIONAL FEATURE) . . . . . . . . . . . . . . . . . . . . . . . . ...84


Synchronization with Auxiliary Axes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 84
Synchronized Arms . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 84
Motion limitation of the two Arms . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 86
Jogging Synchronized Arms . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 86
Teaching and Modifying Positions (REC/MOD) with Synchronized Arms . . . . . . . . . . . . . . . . . 86
Loss of Synchronization. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 87
Run-time modifying the Linear Speed Override. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 87

7. COOPERATIVE MOTION (OPTIONAL FEATURE) . . . . . . . . . . . . . . . . . . . . . . . . . ...89


Cooperative Motion with Auxiliary Axes. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 90
Cooperative Arms . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 91
Multi-cooperative motion . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 92

lb-rc-c5e-motion_enTOC.fm
5
Summary

Jogging . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 93

8. SENSOR TRACKING (OPTIONAL FEATURE) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ..94


Principle of operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 94
Configuration on several arms . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 96
Sensor interface. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 96
Integrated Sensors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 97
External sensors. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 97
Sensor reference system . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 98
Sensor integral with the tool (TOOL) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 98
Sensor integral with the user reference system (USER) . . . . . . . . . . . . . . . . . . . . . . . . . . . . 99
Sensor integral with the world reference system (WORLD). . . . . . . . . . . . . . . . . . . . . . . . . . 99
Sensor integral with the weaving reference system (WEAVE). . . . . . . . . . . . . . . . . . . . . . . . 99
Type of information acquired by the sensor. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 100
Correction actuation criteria . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 100
Relative and absolute deviations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 100
Actuation of deviation in time . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 102
Overall deviations control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 104
Sensor tracking enable mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 104
Sensor malfunctioning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 106
Robot stop in the case of sensor malfunctioning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 106
Redefinition of overall deviations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 106
Accumulative overall deviations management. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 108
Interrupted sensor tracking session . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 108
Suspended sensor tracking session. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 109
Resetting in spread condition . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 109
Limitations in parameter changes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 110
Programming example. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 111

9. CONVEYOR TRACKING
(OPTIONAL FEATURE) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ..113
Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 114
Working Principle . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 116
Process Monitoring . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 118
Tracking Window . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 118
Motion Statements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 119
Teaching Positions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 120
Tracking Interruption . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 120
Limitations during Conveyor Tracking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 120
Use of the Roto-translating Conveyor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 123
Configuration parameters. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 125

lb-rc-c5e-motion_enTOC.fm
6
Summary

10. MOTION WITH WEAVING (OPTIONAL FEATURE) . . . . . . . . . . . . . . . . . . . . . . . . ...126


Weaving Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 126
Weaving Activation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 126
Weaving Parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 127
Wave Shape. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 128
Weave Plane . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 131
Weave Amplification. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 133
Stopping Motions with Weaving. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 134
Programming Weaving . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 135
Weaving without Arm motion . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 136
Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 136
Activation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 136
Parameters. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 137
Example - Using the weaving without Arm motion. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 137
Weaving on multiarm systems . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 138

11. PATH GOVERNOR (OPTIONAL FEATURE) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ...139


Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 139
Enable Path Governor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 139
Disable Path Governor. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 141

12. SMARTMOVE (OPTIONAL FEATURE) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ...142


Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 142
Jerk Limitation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 143
Cartesian Motions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 143

13. JOINT SOFT SERVO (OPTIONAL FEATURE). . . . . . . . . . . . . . . . . . . . . . . . . . . . ...144


Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 144

14. FLOW MODULATE


ALGORITHM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ...145

15. PRESUPPOSITIONS FOR SMART ROBOT PROGRAMMING . . . . . . . . . . . . . . . ...147


Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 147
Glossary. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 148
Offset algorithm with Dynamic Model . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 149
Kinematic offset algorithm (optional feature) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 149
Moving through axis 5 singularities . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 149

lb-rc-c5e-motion_enTOC.fm
7
Summary

Using WRIST_JNT modality to go through singularities . . . . . . . . . . . . . . . . . . . . . . . . . . . 149


Using WRIST_JNT modality to go through singularities. . . . . . . . . . . . . . . . . . . . . . . . . . .151
Manual motion (jog keys) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 152
Robots without compensation (effect of the inverse kinematics) . . . . . . . . . . . . . . . . . . . . . . . 153
Inverse conversion of SMART NJ4 (non-spherical wrist) model . . . . . . . . . . . . . . . . . . . . . 153
Approximation in the orientation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .153
Move to a taught POSITION. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .153
Fly between MOVE LINEAR/CIRCULAR and MOVE JOINT . . . . . . . . . . . . . . . . . . . . . . .154
Axis 5 singularity. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .154
Cartesian position out of range. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .156
TCP in the back of the robot. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .157
TCP behind axis 2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .158
WCP close to axis 1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .160
Inverse conversion of SMART NJ models (spherical wrist only) . . . . . . . . . . . . . . . . . . . . . 160
Axis 5 singularity. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .160
Programming rules for non-spherical wrist robots (SMART NJ4) . . . . . . . . . . . . . . . . . . . . . . 160
How to stay away from a singularity zone . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 161
Changing the orientation of the points along the path . . . . . . . . . . . . . . . . . . . . . . . . . . . .161
Properly designing the work-cell layout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .163
Modifying tool inserting a small angle between robot flange and tool flange . . . . . . . . . . .165
Conclusions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 167

16. COLLISION DETECTION


(OPTIONAL FEATURE) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ..169
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 169
Basic concepts. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 169
Activation/deactivation of Collision Detection function. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 170
Collision Detection sensitivity type. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 171
$COLL_TYPE. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 171
$ARM_SENSITIVITY (sensitivity threshold of the axes) . . . . . . . . . . . . . . . . . . . . . . . . . . . 172
$COLL_SOFT_PER (axes compliance thresholds) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 173
Reliability . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 174
Notes about the collision detection use procedure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 174
Introduction. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 174
Use of the Collision Detection Procedure. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 175
Sample Programs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 178
Enabling the Collision Detection functionality for a single MOVE statement . . . . . . . . . . . . 179
Enabling Collision Detection again from within a Program. . . . . . . . . . . . . . . . . . . . . . . . . . 180
Automatic calculation of the sensitivity thresholds . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 181
Managing "collision detected" event. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 182
Use of CDetect open source library . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 183

17. USE OF POSITIONERS MANAGED BY C5G . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ..185


Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 185
Summary . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 185

lb-rc-c5e-motion_enTOC.fm
8
Summary

General Conventions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 186


Axis rotation directions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 186
Convention for the mechanical positioning of points P1, P2 and P3 . . . . . . . . . . . . . . . . . . 186
Programming override value calculation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 187
Positioners with 1 rotating axis type MP, PTDO, PTDV, TR3000/6000. . . . . . . . . . . . . . . . . . 188
Definition of the reference system . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 188
Calibration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 189
Kinematic description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 189
PTORB - Positioner with 2 perpendicular axes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 190
Positioner with two tilting-rotating axes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 190
Definition of the reference system . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .190
Calibration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .190
Kinematic description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .191
Positioner with two axes in "L" arrangement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 192
Definition of the reference system . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .192
Calibration. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .193
Kinematic description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .194
Positioners with 2 non perpendicular axes, type PTORB-alfa . . . . . . . . . . . . . . . . . . . . . . . . . 195
Definition of the reference system . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 195
Calibration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 196
Kinematic description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 196
Integrated robot positioning axes. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 198
Integrated slide. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 198
Definition of the reference system . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .198
Calibration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .199
Kinematic description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .199
Integrated rotating column . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 201
Definition of the reference system . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .201
Calibration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .202
Kinematic description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .202
Three linear axes portal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 203
Definition of the reference system . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .203
Calibration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .204
Kinematic description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .204
Two linear axes Portal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 205
Definition of the reference system . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .206
Calibration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .206
Kinematic description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .207
Integrated trans-rotational Column. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 207
Definition of the reference system . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .208
Calibration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .209
Kinematic description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .209

18. TO_SET PROGRAM - TOOL HANDLING. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ...211


Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 211
Activation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 211
First screen page of TO_SET . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 213
TOOL automatic calculation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 214

lb-rc-c5e-motion_enTOC.fm
9
Summary

Needed Tools . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 214


Calibrated tool (Tool Master) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .214
Reference point (or master cube). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .215
General characteristics. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 215
Tool orientation calculation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .215
How to identify the "dummy reference system" . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .216
Procedure. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 216
Tool calculation with standard method - Complete procedure . . . . . . . . . . . . . . . . . . . . . . . 218
Tool verification with standard method - Partial procedure . . . . . . . . . . . . . . . . . . . . . . . . . 220
Tool Calculation with "4 points method" - Complete procedure . . . . . . . . . . . . . . . . . . . . 225
Local Tool verification with "4 points method" . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .229
REMOTE TOOL Automatic Calculation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 230
Tools needed . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .230
Tool with known dimensions mounted on Robot Flange . . . . . . . . . . . . . . . . . . . . . . . .230
General characteristics. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .230
UFRAME automatic calculation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 231
Needed Tools . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 231
Tool with known dimensions mounted on Robot Flange . . . . . . . . . . . . . . . . . . . . . . . . . .231
3 Reference Points (ORIGIN, Xpos and XYpos) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .231
General characteristics. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 231
Procedure. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 232
REMOTE UFRAME automatic calculation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 237
Needed Tools . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .237
Tool with known dimensions mounted onto the Robot Flange . . . . . . . . . . . . . . . . . . . .237
3 reference points (ORIGIN, Xpos and XYpos) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .237
General characteristics. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .237
Procedure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .238
BASE automatic calculation for POSITIONERS (optional) . . . . . . . . . . . . . . . . . . . . . . . . . . . 243
Tools required . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 243
Tool of known dimensions mounted on the robot flange . . . . . . . . . . . . . . . . . . . . . . . . . .243
3 reference points (P1, P2, P3) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .243
General characteristics. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 243
Payload identification (optional function) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 252
Basic concepts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 252
Procedure. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 253
Requirements to modify Payload identification programs . . . . . . . . . . . . . . . . . . . . . . . . .254
Activation and execution of the Payload identification procedure . . . . . . . . . . . . . . . . . . .254
Software to validate the payload (SMART Payload) . . . . . . . . . . . . . . . . . . . . . . . . . . . . .263

19. INTERFERENCE REGIONS (OPTIONAL FEATURE) . . . . . . . . . . . . . . . . . . . . . . . ..264


Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 264
Regions types . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 264
Cartesian Forbidden and Allowed Regions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 265
Cartesian Monitored Regions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 265
Joint Forbidden Regions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 265
Joint Monitored Regions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 265
Regions Shape and definition . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 266
Cartesian Regions shape and definition. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 266
Sphere . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .266

lb-rc-c5e-motion_enTOC.fm
10
Summary

Cylinder . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .267
Box . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .267
Plane . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .268
Joint Regions shape and definition . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 268
IR_LIB library to support Interference Regions creation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 269
Examples . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 271
Sample program for Cartesian Interference Regions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 272
Sample program for a Joint Interference Region . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 273

20. AXES PURSUIT (OPTIONAL FEATURE) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ...274


Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 274
Axes Pursuit. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 274
Error handling when Axes Pursuit functionality is active . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 275
Configuring the software option . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 275
Example of PDL2 statements for configuring the Axes Pursuit functionality . . . . . . . . . . . . 276

21. LOW RESOLUTION EULER ANGLES (OPTIONAL FEATURE) . . . . . . . . . . . . . . ...277

lb-rc-c5e-motion_enTOC.fm
11
Preface

PREFACE
– Symbols used in the manual
– Reference documents
– Modification History.

Symbols used in the manual


The symbols for WARNING, CAUTION and NOTES are indicated below together with
their significance.

This symbol indicates operating procedures, technical information and precautions that
if ignored and/or are not performed correctly could cause injuries.

This symbol indicates operating procedures, technical information and precautions that
if ignored and/or are not performed correctly could cause damage to the equipment.

This symbol indicates operating procedures, technical information and precautions that
it are important to highlight.

HS-0-0-0-mot_01.fm
10/0713 12
Preface

Reference documents
This document refers to the C5G Control Unit.
The complete set of manuals for the C5G consists of:

Comau C5G Control Unit – Technical Specifications


– Transport and installation
– C5G Control Unit Use.

These manuals are to be integrated with the following documents:

Comau Robot – Technical Specifications


– Transport and installation
– Maintenance
Programming – PDL2 Programming Language
– VP2 - Visual PDL2
– Motion programming
Applications – According to the required type of
application.

HS-0-0-0-mot_01.fm
13 10/0713
Preface

Modification History
– Version 02/0710:
• Chapter TO_SET Program - Tool handling - the calling level of the Payload
identification (optional function) procedure and the format of the TO_SET
Program screen pages, have been modified.
• New Chap.19. - Interference Regions (optional feature) has been added.
– Version 03/0111:
• added par. 16.7.5 Use of CDetect open source library on page 183 in
Chap.16. - Collision Detection (optional feature),
• added Chap.20. - Axes Pursuit (optional feature),
• added description for Weaving with Circular wave in Chap.10. - Motion with
Weaving (optional feature).
– Version 04/0711:
• added par. 7.3 Multi-cooperative motion on page 92 in Chap.7. - Cooperative
Motion (optional feature), to handle the cooperation among two arms and the
same group of auxiliary axes (e.g. a positioner).
• the description of Chap.19. - Interference Regions (optional feature) and the
corresponding examples has been improved.
– Version 05/0312:
• added details about the use of Synchronized Motion with enabled
Cooperative Motion (see note in par. 6.2 Synchronized Arms on page 84)
• added Chap.9. - Conveyor Tracking (optional feature), describing Conveyor
tracking optional functionality
• added par. 10.7 Weaving on multiarm systems on page 138. Please read
carefully the following warning note, about this functionality (also written in the
above indicated paragraph):

WARNING - There could be a conflict with the previous versions: if the following
statements have been written
– $WEAVE_NUM := 1
– MOVE TO p1 -- it is the default Arm, so weaving is activated
– $WEAVE_NUM := 2
– MOVE ARM[2] TO p2 -- in current version, ARM 2 does not weave because
-- $WEAVE_NUM is set for the $PROG_ARM i.e. ARM 1.

– Version 07/0912:
• added description for a new type of Interference Region: Allowed Region (see
par. 19.2.1 Cartesian Forbidden and Allowed Regions on page 265).
– Version 08/1012:
• added cross-references between software options and corresponding Comau
codes
• added description about how to configure $AX_PURSUIT_LINKED
predefined variable (see par. 20.4 Configuring the software option on
page 275).
– Version 09/0313:
• the Recovery procedure description has been improved.
– Version 10/0713:
• new chapter Joint Soft Servo (optional feature) has been created to describe
the Soft Servo functionality at axes level.

HS-0-0-0-mot_01.fm
10/0713 14
General Safety Precautions

1. GENERAL SAFETY PRECAUTIONS

It deals with a general specification that apply to the whole Robot System. Due to its
significance, this document is referred to unreservedly in any system instruction manual.

This specification deals with the following topics:


– Responsibilities
– Safety Precautions.

1.1 Responsibilities

– The system integrator is responsible for ensuring that the Robot System (Robot
and Control System) are installed and handled in accordance with the Safety
Standards in force in the country where the installation takes place. The application
and use of the protection and safety devices necessary, the issuing of declarations
of conformity and any CE markings of the system are the responsibility of the
Integrator.
– COMAU Robotics & Service shall in no way be held liable for any accidents caused
by incorrect or improper use of the Robot System (Robot and Control System), by
tampering with circuits, components or software, or the use of spare parts that are
not included in the spare parts list.

– The application of these Safety Precautions is the responsibility of the persons


assigned to direct / supervise the activities indicated in the Applicability sectionally
are to make sure that the Authorised Personnel is aware of and scrupulously follow
the precautions contained in this document as well as the Safety Standards in
addition to the Safety Standards in force in the country in which it is installed.
– The non-observance of the Safety Standards could cause injuries to the operators
and damage the Robot System (Robot and Control System).

The installation shall be made by qualified installation Personnel and should conform to
all national and local codes.

ge-0-0-0_01.FM
16 00/1011
General Safety Precautions

1.2 Safety Precautions

1.2.1 Purpose
These safety precautions are aimed to define the behaviour and rules to be observed
when performing the activities listed in the Applicability section.

1.2.2 Definitions
Robot System (Robot and Control System)
The Robot System is a functional unit consisting of Robot, Control Unit, Programming
terminal and possible options.

Protected Area
The protected area is the zone confined by the safety barriers and to be used for the
installation and operation of the robot

Authorised Personnel
Authorised personnel defines the group of persons who have been trained and assigned
to carry out the activities listed in the Applicability section.

Assigned Personnel
The persons assigned to direct or supervise the activities of the workers referred to in
the paragraph above.

Installation and Putting into Service


The installation is intended as the mechanical, electrical and software integration of the
Robot and Control System in any environment that requires controlled movement of
robot axes, in compliance with the safety requirements of the country where the system
is installed.

Programming Mode
Operating mode under the control of the operator, that excludes automatic operation
and allows the following activities: manual handling of robot axes and programming of
work cycles at low speed, programmed cycle testing at low speed and, when allowed,
at the working speed.

Auto / Remote Automatic Mode


Operating mode in which the robot autonomously executes the programmed cycle at the
work speed, with the operators outside the protected area, with the safety barriers
closed and the safety circuit activated, with local (located outside the protected area) or
remote start/stop.

Maintenance and Repairs


Maintenance and repairs are activities that involve periodical checking and / or
replacement (mechanical, electrical, software) of Robot and Control System parts or
components, and trouble shooting, that terminates when the Robot and Control System
has been reset to its original project functional condition.

ge-0-0-0_01.FM
00/1011 17
General Safety Precautions

Putting Out of Service and Dismantling


Putting out of service defines the activities involved in the mechanical and electrical
removal of the Robot and Control System from a production unit or from an environment
in which it was under study.
Dismantling consists of the demolition and dismantling of the components that make up
the Robot and Control System.

Integrator
The integrator is the professional expert responsible for the installation and putting into
service of the Robot and Control System.

Incorrect Use
Incorrect use is when the system is used in a manner other than that specified in the
Technical Documentation.

Range of Action
The robot range of action is the enveloping volume of the area occupied by the robot
and its fixtures during movement in space.

1.2.3 Applicability
These Specifications are to be applied when executing the following activities:
– Installation and Putting into Service
– Programming Mode
– Auto / Remote Automatic Mode
– Robot axes release
– Maintenance and Repairs
– Putting Out of Service and Dismantling

ge-0-0-0_01.FM
18 00/1011
General Safety Precautions

1.2.4 Operating Modes


Installation and Putting into Service
– Putting into service is only possible when the Robot and Control System has been
correctly and completely installed.
– The system installation and putting into service is exclusively the task of the
authorised personnel.
– The system installation and putting into service is only permitted inside a protected
area of an adequate size to house the robot and the fixtures it is outfitted with,
without passing beyond the safety barriers. It is also necessary to check that under
normal robot movement conditions there is no collision with parts inside the
protected area (structural columns, power supply lines, etc.) or with the barriers. If
necessary, limit the robot working areas with mechanical hard stop (see optional
assemblies).
– Any fixed robot control protections are to be located outside the protected area and
in a point where there is a full view of the robot movements.
– The robot installation area is to be as free as possible from materials that could
impede or limit visibility.
– During installation the robot and the Control Unit are to be handled as described in
the product Technical Documentation; if lifting is necessary, check that the
eye-bolts are fixed securely and use only adequate slings and equipment.
– Secure the robot to the support, with all the bolts and pins foreseen, tightened to
the torque indicated in the product Technical Documentation.
– If present, remove the fastening brackets from the axes and check that the fixing
of the robot fixture is secured correctly.
– Check that the robot guards are correctly secured and that there are no moving or
loose parts. Check that the Control Unit components are intact.
– If applicable, connect the robot pneumatic system to the air distribution line paying
attention to set the system to the specified pressure value: a wrong setting of the
pressure system influences correct robot movement.
– Install filters on the pneumatic system to collect any condensation.
– Install the Control Unit outside the protected area: the Control Unit is not to be used
to form part of the fencing.
– Check that the voltage value of the mains is consistent with that indicated on the
plate of the Control Unit.
– Before electrically connecting the Control Unit, check that the circuit breaker on the
mains is locked in open position.

– Connection between the Control Unit and the three-phase supply mains at the
works, is to be with a four-pole (3 phases + earth) armoured cable dimensioned
appropriately for the power installed on the Control Unit. See the product
Technical Documentation.
– The power supply cable is to enter the Control Unit through the specific fairlead and
be properly clamped.
– Connect the earth conductor (PE) then connect the power conductors to the main
switch.

ge-0-0-0_01.FM
00/1011 19
General Safety Precautions

– Connect the power supply cable, first connecting the earth conductor to the circuit
breaker on the mains line, after checking with a tester that the circuit breaker
terminals are not powered. Connect the cable armouring to the earth.
– Connect the signals and power cables between the Control Unit and the robot.
– Connect the robot to earth or to the Control Unit or to a nearby earth socket.
– Check that the Control Unit door (or doors) is/are locked with the key.
– A wrong connection of the connectors could cause permanent damage to the
Control Unit components.
– The C5G Control Unit manages internally the main safety interlocks (gates,
enabling pushbuttons, etc.). Connect the C5G Control Unit safety interlocks to the
line safety circuits, taking care to connect them as required by the Safety
standards. The safety of the interlock signals coming from the transfer line
(emrgency stop, gates safey devices etc) i.e. the realisation of correct and safe
circuits, is the responsibility of the Robot and Control System integrator.

In the cell/line emergency stop circuit the contacts must be included of the control unit
emergency stop buttons, which are on X30. The push buttons are not interlocked in the
emergency stop circuit of the Control Unit.

– The safety of the system cannot be guaranteed if these interlocks are wrongly
executed, incomplete or missing.
– The safety circuit executes a controlled stop (IEC 60204-1 , class 1 stop) for the
safety inputs Auto Stop/ General Stop and Emergency Stop. The controlled stop is
only active in Automatic states; in Programming the power is cut out (power
contactors open) immediately. The procedure for the selection of the controlled
stop time (that can be set on SDM board) is contained in the Installation manual .
– When preparing protection barriers, especially light barriers and access doors,
bear in mind that the robot stop times and distances are according to the stop
category (0 or 1) and the weight of the robot.

Check that the controlled stop time is consistent with the type of Robot connected to the
Control Unit. The stop time is selected using selector switches SW1 and SW2 on the
SDM board.

– Check that the environment and working conditions are within the range specified
in the specific product Technical Documentation.
– The calibration operations are to be carried out with great care, as indicated in the
Technical Documentation of the specific product, and are to be concluded
checking the correct position of the machine.
– To load or update the system software (for example after replacing boards), use
only the original software handed over by COMAU Robotics & Service.
Scrupulously follow the system software uploading procedure described in the
Technical Documentation supplied with the specific product. After uploading,
always make some tests moving the robot at slow speed and remaining outside the
protected area.
– Check that the barriers of the protected area are correctly positioned.

ge-0-0-0_01.FM
20 00/1011
General Safety Precautions

Programming Mode
– The robot is only to be programmed by the authorised personnel.
– Before starting to program, the operator must check the Robot System (Robot and
Control System) to make sure that there are no potentially hazardous irregular
conditions, and that there is nobody inside the protected area.
– When possible the programming should be controlled from outside the protected
area.
– Before operating inside the Protected Area, the operator must make sure from
outside that all the necessary protections and safety devices are present and in
working order, and especially that the hand-held programming unit functions
correctly (slow speed, emergency stop, enabling device, etc.).
– During the programming session, only the operator with the hand-held terminal is
allowed inside the Protected Area.
– If the presence of a second operator in the working area is necessary when
checking the program, this person must have an enabling device interlocked with
the safety devices.
– Activation of the motors (Drive On) is always to be controlled from a position
outside the range of the robot, after checking that there is nobody in the area
involved. The Drive On operation is concluded when the relevant machine status
indication is shown.
– When programming, the operator is to keep at a distance from the robot to be able
to avoid any irregular machine movements, and in any case in a position to avoid
the risk of being trapped between the robot and structural parts (columns, barriers,
etc.), or between movable parts of the actual robot.
– When programming, the operator is to avoid remaining in a position where parts of
the robot, pulled by gravity, could execute downward movements, or move
upwards or sideways (when installed on a sloped plane).
– Testing a programmed cycle at working speed with the operator inside the
protected area, in some situations where a close visual check is necessary, is only
to be carried out after a complete test cycle at slow speed has been executed. The
test is to be controlled from a safe distance.
– Special attention is to be paid when programming using the hand-held terminal: in
this situation, although all the hardware and software safety devices are active, the
robot movement depends on the operator.
– During the first running of a new program, the robot may move along a path that is
not the one expected.
– The modification of program steps (such as moving by a step from one point to
another of the flow, wrong recording of a step, modification of the robot position out
of the path that links two steps of the program), could give rise to movements not
envisaged by the operator when testing the program.
– In both cases operate cautiously, always remaining out of the robot’s range of
action and test the cycle at slow speed.

ge-0-0-0_01.FM
00/1011 21
General Safety Precautions

Auto / Remote Automatic Mode


– The activation of the automatic operation (AUTO and REMOTE states) is only to
be executed with the Robot System (Robot and Control System) integrated inside
an area with safety barriers properly interlocked, as specified by Safety Standards
currently in force in the Country where the installation takes place.
– Before starting the automatic mode the operator is to check the Robot and Control
System and the protected area to make sure there are no potentially hazardous
irregular conditions.
– The operator can only activate automatic operation after having checked:
• that the Robot and Control System is not in maintenance or being repaired;
• the safety barriers are correctly positioned;
• that there is nobody inside the protected area;
• that the Control Unit doors are closed and locked;
• that the safety devices (emergency stop, safety barrier devices) are
functioning;
– Special attention is to be paid when selecting the automatic-remote mode, where
the line PLC can perform automatic operations to switch on motors and start the
program.

Robot axes release


– In the absence of motive power, the robot axes movement is possible by means of
optional release devices and suitable lifting devices. Such devices only enable the
brake deactivation of each axis. In this case, all the system safety devices
(including the emergency stop and the enable button) are cut out; also the robot
axes can move upwards or downwards because of the force generated by the
balancing system, or the force of gravity.

Before using the manual release devices, it is strongly recommended to sling the robot,
or hook to an overhead travelling crane.

– Enabling the brake releasing device may cause the axes falling due to gravity as
well as possible impacts due to an incorrect restoration, after applying the brake
releasing module. The procedure for the correct usage of the brake releasing
device (both for the integrated one and module one) is to be found in the
maintenance manuals.
– When the motion is enabled again following the interruption of an unfinished
MOVE, the track recovery typical function may generate unpredictable paths that
may imply the risk of impact. This same condition arises at the next automatic cycle
restarting. Avoid moving the Robot to positions that are far away from the ones
provided for the motion restart; alternatively disable the outstanding MOVE
programmes and/or instructions.

Maintenance and Repairs


– When assembled in COMAU Robotics & Service, the robot is supplied with
lubricant that does not contain substances harmful to health, however, in some
cases, repeated and prolonged exposure to the product could cause skin irritation,
or if swallowed, indisposition.
First Aid. Contact with the eyes or the skin: wash the contaminated zones with
abundant water; if the irritation persists, consult a doctor.

ge-0-0-0_01.FM
22 00/1011
General Safety Precautions

If swallowed, do not provoke vomiting or take anything by mouth, see a doctor as


soon as possible.
– Maintenance, trouble-shooting and repairs are only to be carried out by authorised
personnel.
– When carrying out maintenance and repairs, the specific warning sign is to be
placed on the control panel of the Control Unit, stating that maintenance is in
progress and it is only to be removed after the operation has been completely
finished - even if it should be temporarily suspended.
– Maintenance operations and replacement of components or the Control Unit are to
be carried out with the main switch in open position and locked with a padlock.
– Even if the Control Unit is not powered (main switch open), there may be
interconnected voltages coming from connections to peripheral units or external
power sources (e.g. 24 Vdc inputs/outputs). Cut out external sources when
operating on parts of the system that are involved.
– Removal of panels, protection shields, grids, etc. is only allowed with the main
switch open and padlocked.
– Faulty components are to be replaced with others having the same code, or
equivalent components defined by COMAU Robotics & Service.

After replacement of the SDM module, check on the new module that the setting of the
stop time on selector switches SW1 and SW2 is consistent with the type of Robot
connected to the Control Unit.

– Trouble-shooting and maintenance activities are to be executed, when possible,


outside the protected area.
– Trouble-shooting executed on the control is to be carried out, when possible
without power supply.
– Should it be necessary, during trouble-shooting, to intervene with the Control Unit
powered, all the precautions specified by Safety Standards are to be observed
when operating with hazardous voltages present.
– Trouble-shooting on the robot is to be carried out with the power supply cut out
(Drive off).
– At the end of the maintenance and trouble-shooting operations, all deactivated
safety devices are to be reset (panels, protection shields, interlocks, etc.).
– Maintenance, repairs and trouble-shooting operations are to be concluded
checking the correct operation of the Robot System (Robot and Control System)
and all the safety devices, executed from outside the protected area.
– When loading the software (for example after replacing electronic boards) the
original software handed over by COMAU Robotics & Service is to be used.
Scrupulously follow the system software loading procedure described in the
specific product Technical Documentation; after loading always run a test cycle to
make sure, remaining outside the protected area
– Disassembly of robot components (motors, balancing cylinders, etc.) may cause
uncontrolled movements of the axes in any direction: before starting a disassembly
procedure, consult the warning plates applied to the robot and the Technical
Documentation supplied.
– It is strictly forbidden to remove the protective covering of the robot springs.

ge-0-0-0_01.FM
00/1011 23
General Safety Precautions

Putting Out of Service and Dismantling


– Putting out of service and dismantling the Robot and Control System is only to be
carried out by Authorised Personnel.
– Bring the robot to transport position and fit the axis clamping brackets (where
applicable) consulting the plate applied on the robot and the robot Technical
Documentation.
– Before stating to put out of service, the mains voltage to the Control Unit must be
cut out (switch off the circuit breaker on the mains distribution line and lock it in
open position).
– After using the specific instrument to check there is no voltage on the terminals,
disconnect the power supply cable from the circuit breaker on the distribution line,
first disconnecting the power conductors, then the earth. Disconnect the power
supply cable from the Control Unit and remove it.
– First disconnect the connection cables between the robot and the Control Unit,
then the earth cable.
– If present, disconnect the robot pneumatic system from the air distribution line.
– Check that the robot is properly balanced and if necessary sling it correctly, then
remove the robot securing bolts from the support.
– Remove the robot and the Control Unit from the work area, applying the rules
indicated in the products Technical Documentation; if lifting is necessary, check the
correct fastening of the eye-bolts and use appropriate slings and equipment only.
– Before starting dismantling operations (disassembly, demolition and disposal) of
the Robot and Control System components, contact COMAU Robotics & Service,
or one of its branches, who will indicate, according to the type of robot and Control
Unit, the operating methods in accordance with safety principles and safeguarding
the environment.
– The waste disposal operations are to be carried out complying with the legislation
of the country where the Robot and Control System is installed.

ge-0-0-0_01.FM
24 00/1011
General Safety Precautions

1.2.5 Performance
The performances below shall be considered before installing the robot system:
– Stop distances
– Mission time (typ. case).

Stop distances
– With Robot in programming modality (T1), if you press the stop pushbutton (red
mushroom-shaped one on WiTP) in category 0 (according to the standard
EN60204-1), you will obtain:

Tab. 1.1 - Stop spaces in programming modality (T1)

Expected Stopping Stopping


Mode Case
speed time space
Nominal 120 ms 30 mm
T1 250 mm/s
Limit 500 ms 125 mm

Tab. 1.2 - Safety electronics reaction time in programming modality (T1)

Expected Stopping
Mode Case
speed time
For the safety inputs of the SDM module (e.g.
stop pushbutton of TP in wired version)
For the stop stop and enabling device inputs 150 ms
from the TP in wireless version, when the
T1 250 mm/s
safety wire transmission is active.
For the time-out of stop input and enabling
device from TP in wireless version, when the 350 ms
safety wire transmission is lost or interrupted.

– Considering the Robot in automatic modality, under full extension, full load and
maximum speed conditions, if you press the stop pushbutton (red
mushroom-shaped one on WiTP) in category 1 (according to norm EN60204-1)
you will trigger the Robot complete stop with controlled deceleration ramp.
Example: for Robot NJ 370-2.7 you will obtain the complete stop in about 85 °
motion, that correspond to about 3000 mm movement measured on TCP flange.
Under the said conditions, the stopping time for Robot NJ 370-2.7 is equal to 1,5
seconds.
– For each Robot type the limit stop time can be required to COMAU Robotics g

Mission time (typ. case)


– We remind you that the safety system efficiency covering is equal to 20 years
(mission time of safety-related parts of control systems (SRP/CS), according to
EN ISO 13849-1).

ge-0-0-0_01.FM
00/1011 25
System operating modes and states

2. SYSTEM OPERATING MODES AND STATES

2.1 Foreword
This chapter describes the following:
– System operating modes
– System states
– Stand-by function

2.2 System operating modes


The C5G Robot Control Unit can operate in three different modes that can be selected
through the modal selector switch on the Teach Pendant:
– programming (T1),

– local automatic (AUTO) and

– remote automatic (REMOTE).

Local automatic mode (AUTO) is used to execute production programs; as they


contain instructions for the robot movement, to be able to start it is necessary to press
the START key on the Teach Pendant. The status selector switch must be set on AUTO.
Active TOOL, BASE and FRAME cannot be changed when working in AUTO.
The Automatic remote mode (REMOTE) is the same as Automatic local mode
(AUTO), but the commands (for example the start) are sent from a remote device (for
example a PLC).
The state selector switch must be set to the REMOTE position. Active TOOL, BASE and
FRAME cannot be changed when working in REMOTE.
The Programming mode (T1) is used to create and verify programs The robot moves,
for safety reasons, are run at a lower speed than in automatic mode (maximum robot
speed allowed in programming is 250 mm/s on the flange centre).

HS-0-C5E-USO_32.fm
26 00/0310
System operating modes and states

When the status selector switch is set on position T1, the programs can be developed
using editor environment and the spots can be taken from the Teach Pendant moving
the robot manually with the motion keys; the programs can be set up using the debug
tools of the system. In programming mode, the execution of a move instruction requires
that the operator presses the START key and the enable device on the Teach Pendant.
When the status selector switch has been set on T1, the system is under the control of
the operator. When the selector is set on REMOTE, the system is under remote control
(for example from PLC).
Active TOOL, BASE and FRAME cannot be changed when working in REMOTE.
Before any operation can be executed that requires movement, the drives must be
powered:
– if the state selector switch is in T1 position, press in the intermediate position the
Teach Pendant Enabling Device, to power ON the drives; tho switch them OFF and
activate brakes on all axes controlled by the Control Unit, just release the Teach
Pendant Enabling Device,
– if the state selector switch is in AUTO position, press the R5 softkey (Teach
Pendant right menu - it means DRIVE ON when in AUTO state), to power ON the
drives; to switch them OFF and activate brakes on all axes controlled by the
Control Unit, press the R5 softkey again (Teach Pendant right menu - now it means
DRIVE OFF).
Active TOOL, BASE and FRAME cannot be changed when working in AUTO.
– if the state selector switch is in REMOTE position, DRIVEs ON and OFF are
remote controlled.
A detailed description follows of all the possible system states.

2.3 System states


Mainly, the system status depends on:
– the status selector switch
– the DRIVE ON, DRIVE OFF and HOLD keys on the Teach Pendant
– system alarm
Transition from one state of the system to another is also influenced by the enable
device on the Teach Pendant.
The Control Unit may be in one of these conditions:
– HOLD status: the robot is gradually decelerated until the stopping point is reached;
movement is suspended and also the execution of the movement program
(holdable). When there are all the necessary conditions to exit from the HOLD
status, the system returns to the previous state (programming or automatic), but to
continue to execute the movement program it is necessary to press START.
– AUTO status: this is usually used to execute production programs that control the
robot movements (status selector switch positioned on AUTO or REMOTE or T2).
Active TOOL, BASE and FRAME cannot be changed when working in AUTO or
REMOTE.
– PROGR status: the robot can be moved manually using the jog keys or executing
program instructions (from editor environment or by EXECUTE). In the latter case,

HS-0-C5E-USO_32.fm
00/0310 27
System operating modes and states

in order that the movement be executed, the START key and the enabling button
have to be kept pressed.
If the controlled stop function class 1 (EN 60204-1) is active, the power cut-out (opening
of the power contactor) may take place with a delay that ranges from a minimum of 1
second to a maximum of 2 seconds.
With the status selector switch positioned on T1, the power cut-out is immediate (EN
60204-1, class 0 stop).
– ALARM status: this status is entered when there is a system alarm. According to
how serious the error is, the system takes different actions, such as suspending the
program execution, deactivation of the drives, etc. A situation may occur where the
alarm cannot be reset, therefore the drives cannot be switched on.
The current system status is displayed on the first status line of the Teach Pendant (or
in the Terminal window of tool WinC5G on PC).
The figure shows a simplified diagram of the actions that determine the system
change-over from one state to another.

Fig. 2.1 - Simplified diagram of the system states

1. Status selector switch on T1 + HOLD released


2. HOLD or DRIVES OFF or selector switch change
3. HOLD or DRIVES OFF or selector switch change
4. Status selector switch on AUTO or REMOTE + HOLD released
Note: To perform transient 4 also the enabling device key has to be pressed

2.3.1 HOLD status


The safety rules to be complied to when operating with the Control Unit have been
studied so that the system enters the HOLD status every time a change is made in the
operating mode, passing for instance from LOCAL to PROGR mode.
To exit from the HOLD status to enable a certain operating mode, there must be all the
required safety conditions. A typical example is when the operator brings the status
selector switch to PROGR to work near the robot, holding the Teach Pendant to carry
out learning operations for the points.

HS-0-C5E-USO_32.fm
28 00/0310
System operating modes and states

In PROGR, exiting from HOLD can be obtained by pressing START, this is controlled
by the system and therefore is active when an instruction or a movement program is
executed. When the START key is released again the system returns to HOLD status.
When entering the HOLD status, the corresponding HOLD key on the Teach Pendant
is considered as pressed. Further pressure on the key causes the system to exit from
HOLD status.
If the HOLD status has been caused by pressing the DRIVE OFF key on the Teach
Pendant (either Enabling Device released or R5 softkey pressed meaning DRIVE OFF),
the DRIVE OFF and HOLD keys must be pressed again to exit from HOLD status, and
then re-power the drives (either intermediate pressure of the Enabling Device or press
R5 softkey meaning DRIVE ON).

2.3.2 AUTO status


To have the system in AUTO status, the status selector switch on the Robot Control
Cabinet must be set on AUTO or REMOTE. Active TOOL, BASE and FRAME cannot be
changed when working in AUTO or REMOTE.
In AUTO status, to start programs ready for execution, press the START key on the
Teach Pendant or activate the START input from remote device.
Conditions that change the system status from AUTO to HOLD are:
– status selector switch changed to another position;
– DRIVE OFF or HOLD pressed;
– system alarm.
To return to AUTO, bring the selector switch back to the required position, and press
again the previous buttons (DRIVE OFF and/or HOLD). To continue the movement
program execution, press START after making sure that the drives are powered (DRIVE

2.3.3 PROGR status


PROGR status is active when:
– the status selector switch is set to T1.
In this state the robot can be moved manually, using the jog keys on the Teach Pendant.
It is also possible to run programs from IDE environment (see IDE Page in C5G Control
Unit Use manual) to check that they are correct and if necessary make
changes. Movements are at slow speed.

2.3.4 ALARM status


The system enters ALARM status when an alarm is generated. An error message is
displayed on the second status line of the system screen and the associated LED, next
to the ALARM key on the Teach Pendant, lights up.
There are different conditions that can generate an alarm and the action to be taken to
exit from ALARM status and bring the system back to the previous state vary according
to how serious the error is.

HS-0-C5E-USO_32.fm
00/0310 29
System operating modes and states

2.4 Stand-by function


The purpose of the Stand-by function is to cut down the current consumption when the
robot is stationary.
The function is automatically activated when the Control Unit is in local automatic or
remote automatic mode and after the robot has remained stationary for a time defined
by variable $TUNE [27];this function activates the motor brakes to keep the static
position of the robot. The value of variable $TUNE [27], set by COMAU, is 120 seconds;
if this variable is set to 0 the function is deactivated.
The Stand-by function is automatically deactivated at the first request to start movement
again (START, RESUME) from the system.
The system Stand-by status is displayed in the status bar of the Teach Pendant. To
display the state of a single arm, read this status on the Status sub-page, the Motion
page on the Teach Pendant.

The safety precautions are to be scrupulously observed regarding this operating


condition of the Controller.

HS-0-C5E-USO_32.fm
30 00/0310
Turn-Set and Calibration - Basic Concepts

3. TURN-SET AND CALIBRATION - BASIC


CONCEPTS

3.1 Foreword
The purpose of this chapter is to describe the basic concepts and the terminology for the
management of robot axes position information. The description of the operating
procedures is contained in the chapter TURN-SET AND CALIBRATION
- OPERATING PROCEDURES, that specifically regards the robot used.
This chapter contains the basic information on the following topics:
– used Terminology
– Turn-set
– Calibration

3.2 Terminology
– TRANSDUCER: There are two types of position transducers: encoder and
resolver.
– NUMBER OF TRANSDUCER TURNS: during the robot axis movement, the
transducer may make several turns; the number of turns is initialised through the
calibration or the turn-set.
– AXIS VALUE: the value of an axis contains all the information needed to determine
the exact position of an axis in space;
– VALUE RECONSTRUCTION: when the Control Unit is powered on, the system
software, among the various initialisations, reconstructs the value of the robot
axes.
The system software checks this value; in fact, it checks that the difference
between the reconstructed position and the position before shut-down is below a
certain threshold. If the threshold is exceeded, the Control Unit displays the error
59411 - 08 Ax <num_ax> Arm <num_arm> movement after shut-down and
leaves it to the operator to check that the physical position of the robot corresponds
to the new value.
– CALIBRATION POSITION: a pre-set position that has been checked using
specific equipment (dial gauges, supports, calibration fixtures). The calibration
position is a reference position in the robot working space that serves to initialise
the value of each axis.
– CALIBRATION CONSTANTS: the calibration constant is the difference between
the datum read by the transducer and the nominal position of the robot axis that
the transducer should assume in that particular position of the robot axis. In fact,
since the positioning of the transducer as to the robot joint is casual, (because it
depends on how the transducer has been mounted), it is necessary to correct the
actual position of the transducer according to the nominal position required by the
robot axis.

HS-0-C5E-USO_35.fm
00/0610 31
Turn-Set and Calibration - Basic Concepts

The calibration constant is defined inside a transducer turn and is stored in variable
$CAL_DATA. It is represented in motor turns and is a value between -0.5
(excluded) and +0.5 (included). The calibration constant described in variable
$CAL_DATA can be read on the Teach Pendant, SETUP Page, Calib. subpage.
– CALIBRATION ASCII FILE: the calibration file
UD:\SYS\<$SYS_ID>_CAL<num_arm>.PDL (where $SYS_ID indicates the
system identification, for example NJ4_001) is an ASCII file with syntax of a PDL2
file, where the calibration constants ($CAL_DATA[n]) and other typical data of the
robot are stored.
– NVRAM: the memory used to save the characteristic information of the robot
associated to the Control Unit, the calibration constants and the length of the
levers. It is on the CPU board of the Controller.

3.3 Turn-set
The purpose of the turn-set is to update the number of transducer turns only,
should it occur that the when switched on again, the Control Unit has lost this
value.
The operation consists in bringing the axis involved to the calibration position, using the
locating notches, and giving the required command. No special equipment is needed,
because the only value initialised is the number of turns of the transducer.
The turn-set operation is required when
– there has been axis movement with the control off (for example when the error
59411 - 08 Ax <num_ax> Arm <num_arm> movement after shut-down) is
displayed.
– events take place that cause the loss of the number of turns only, and therefore do
not require the execution of the calibration procedure. On the Teach Pendant
status window or on the PV video the text Ar:TURN is displayed.
According to whether the turn-set is executed with the robot in system calibration
position or in user calibration position, we shall have:
– Turn-set on system calibration position
– Turn-set on user calibration position
– Turn-set for robot axes with multi-turn stroke

3.3.1 Turn-set on system calibration position


Enables the initialising of the number of transducer turns of the individual robot axes, in
the system calibration position (calibration position pre-defined by COMAU
Robotics).
For further information see System calibration ($CAL_SYS).

3.3.2 Turn-set on user calibration position


Enables the initialising of the number of transducer turns of the individual robot axes, in
the user calibration position (“out of range” position defined by the user).
For further information see User calibration ($CAL_USER).

HS-0-C5E-USO_35.fm
32 00/0610
Turn-Set and Calibration - Basic Concepts

3.3.3 Turn-set for robot axes with multi-turn stroke


With robot axes that are able to execute the multi-turn stroke, it may happen that when
carrying out the TURN SET procedure, the mechanical calibration notches are
misaligned (this condition can occur when the robot axis, having made one or more
complete rotations, positions in a mechanical turn that is different to that of the original
calibration).

Fig. 3.1 - Axis Positioning Error in TURN SET

In the above indicated condition, when moving the axis to align the notches, a
positioning error message is shown on the terminal.
5409 - 02 Ax <num_asse> Arm <num_arm> joint position not sufficient
accurate

If the above described conditions occur, do not send the TURN SET command (the axis
would be calibrated in a wrong position), but restore the correct position by performing
one of these procedures:
1. Turn the axis and make attempts to find the axis turn position where the original
calibration was executed. Align the notches and run the TURN SET command.
When the correct position has been resumed, the message Command
Completed will appear on the Terminal
otherwise, as an alternative
2. Make the complete axis calibration (see Chapter Turn-set and Calibration -
Operating Procedures in the Maintenance manual of the corresponding robot)

HS-0-C5E-USO_35.fm
00/0610 33
Turn-Set and Calibration - Basic Concepts

3.4 Calibration
The purpose of the calibration procedure is to establish the position of a robot axis
referring it to an ideal robot. This makes it possible to initialise the values of the robot
axes and to make the position variables used in the robot programs universal.
During the calibration procedure, when the desired axis is in the calibration position, two
values are stored:
– the deviation, inside a transducer turn, between the value of the actual position and
that of the axis nominal position,
– the number of transducer turns.
The notches on the individual axes make it possible to execute future turn-set operations
on a robot that has already been installed.

Remember that executing the calibration operation (on the Teach Pendant, SETUP
Page, Calib subpage, Calib (CAC) command) just having positioned the robot axes on
the locating notches, without using the suitable equipment, is an operation that does not
guarantee the necessary robot positioning precision.

The recovery of the calibration (executed by COMAU), if necessary, is to be executed


when first putting the robot into operation.

Subsequently, the calibration does not need to be executed again, unless there is
a mechanical failure that involves the replacement of a component of the
kinematic chain, or in the case of impacts that damage the robot structure.

The basic concepts are described below for:


– System calibration
– User calibration

3.4.1 System calibration


To initialise the robot axis values in the system calibration position (calibration
position predefined by COMAU Robotics - $CAL_SYS).

To determine the correct calibration position, special equipment has to be used (dial
gauges, supports, etc.) to determine with the necessary precision the position of each
individual axis.

3.4.2 User calibration


User calibration defines a new calibration position that is different to that of the
system.
This type of calibration (commonly called out-of-range calibration) can be used when
the system position is difficult to reach once the robot is inserted in the final application,
and therefore it becomes necessary to define a different calibration position, called user
calibration position ($CAL_USER).

HS-0-C5E-USO_35.fm
34 00/0610
Turn-Set and Calibration - Basic Concepts

It is the responsibility of the user to provide the appropriate instruments and to check the
correct positioning of the robot in any user re-calibrations, especially regarding the
arrangement of the locating notches.

Fig. 3.2 - Summary of Calibration and Turn-Set Operations

SAVING CALIBRATION CONSTANTS


1. NVRAM
2. UD:\SYS in .C5G file
3. UD:\SYS in the calibration ASCII file ($<SYS_ID>_CAL<num_arm>.PDL)
4. Hard copy

HS-0-C5E-USO_35.fm
00/0610 35
Robot motion in Programming mode

4. ROBOT MOTION IN PROGRAMMING MODE

4.1 Introduction
In this chapter, reference will be made to the Teach Pendant as the device to control the
robot motion in programming status (status selector switch in position T1).

For any further information and/or explanations, see the relevant chapter Use of the
Teach Pendant, in the C5G Control Unit Use manual.

A detailed description follows about :


– Reference frames
– System reference frames
– Manual motion
– Manual motion in WRIST_JNT mode
– Manual motion of a single arm system
– Manual motion of auxiliary axes, slides and rotating columns
– Manual motion with Controller multi-arm configuration
– Motion instruction in programming status

4.2 Reference frames


A Cartesian reference system, or reference set of three, is a geometrical concept to
enable the representation of an object in space. For example, the corner of a table may
be chosen as a reference system to represent the table. The same method can be
applied for a book lying on a table, as for a weld gun mounted on the flange of a robot.
A co-ordinates conversion describes the position of one reference system in relation to
another. This is described as a POSITION variable. For example, if a table is located in
a room, its position in relation to the room is indicated by POSITION p_table, that
describes the co-ordinates conversion between the two reference systems. The
co-ordinates conversion can also be used to calculate the position of an object in relation
to different reference systems. For example, a book with a position in relation to the
corner of the table is p_book and will have the position (p_table:p_book) in relation to
the corner of the room. The sign (:) indicates the relevant position operation, and makes
it possible to compose the effect of various co-ordinate conversions. For further
information, see the PDL2 Programming Language Manual.

4.3 System reference frames


The Controller has three system variables ($BASE, $TOOL and $UFRAME) that permit

HS-0-C5E-USO_33.fm
36 10/0713
Robot motion in Programming mode

the description of the main co-ordinate conversions. Before starting to explain these
conversions, it is necessary to define some reference frames.

World frame – Workshop reference frame in relation to where the


machines are positioned
Base frame – frame that indicates the robot base
User frame – frame that indicates the workpiece
Flange frame – frame that indicates the robot flange
TCP frame – frame that indicates the tool tip

The $TOOL variable describes the position of the TCP frame in relation to the flange;
the $BASE variable describes the position of the base frame in relation to the world
frame; finally, the $UFRAME variable describes the position of the workpiece in relation
to the world frame.
The POS conversion indicates the recorded point P where the TCP will position when
executing the program. It must be remembered that all the POSITIONS recorded are
defined in relation to the user reference frame (defined by $UFRAME, with certain
$BASE and $TOOL values).

Remember that, changing $TOOL or $BASE or $UFRAME, the same position (POS)
corresponds to a different actual position of the robot!

Fig. 4.1 - System reference frame and movement of the co-ordinates

1. Flange frame
2. Tool frame
3. Recorded position
4. User frame
5. Base frame
6. World frame

Let’s now imagine a pen fitted on the flange of the robot that has to write the word
COMAU on the table. The $BASE conversion defines the point where the robot base is

HS-0-C5E-USO_33.fm
10/0713 37
Robot motion in Programming mode

located, the $TOOL movement indicates the pen and the $UFRAME movement
indicates the position of the table.

4.4 Manual motion


The manual movement of the arm is necessary in certain circumstances, among which
when learning (recording) the positions or during maintenance of the tool fitted on the
arm. The black keys on the Teach Pendant are used for manual motion. To be able to
make the move it is necessary to have the system in programming status, i.e. with the
status selector switch in position T1, and the Enabling Device pressed.
Before starting to move, the movement mode and the speed should be selected.
From the Motion page of the Teach Pendant, Basic sub-page (COORD field), one of the
following modes can be selected to move the arm:
– JOINT - joints mode. The ‘+/-’ keys are associated to each of the axes of the
selected arm; the keys associated to any auxiliary axes present follow those of the
arm (typically they are keys 7 and 8 (‘+/-’)). When one of the keys is pressed, the
corresponding axis moves in the positive or the negative direction, according to the
directions indicated on the plate on the arm.
– BASE - linear movement mode according to the tool reference x,y,z frame (or TCP
frame). The first three '+/-' keys (on the left) are used for linear motion in the
direction of the three axes of the world reference system); the next three '+/-' keys
(on the right) are for the rotation of the tool around the same axes keeping the TCP
position unchanged.. It must be remembered that the world frame is not defined
directly by any system variable; in fact, it is the robot base that is represented in
relation to the world by means of the $BASE variable.
– TOOL - linear movement mode according to the tool reference x,y,z frame (or TCP
frame). The first three ‘+/-’ keys allow linear movement in the direction, of the three
axes of the tool reference system (defined by the $TOOL variable); the next three
‘+/-’ keys are for the tool rotation around the same axes keeping the TCP position
unchanged (tool working point).
– UFRAME - linear movement mode according to the user reference x,y,z frame (for
example the frame that describes the workpiece). The first three ‘+/-’ keys allow
linear movement in the direction of the three axes of the user reference system
(defined by the $UFRAME variable); the next three ‘+/-’ keys are for the tool
rotation around the same axes keeping the TCP position unchanged.
The speed of the manual motion can be selected with the +% and -% keys that act on a
percentage value shown on the Teach Pendant status bar. This percentage value is
called general override and does not only act on the manual movement speed, but on
all types of movements, both in programming and in automatic mode.
The TCP movement speed, during manual movements, is always lower than the safety
speed of 250 mm/s also in joints mode. In the Cartesian modes (Tool, Uframe, Base)
the maximum speed that can be reached is limited by the system variable
$JOG_SPD_OVR that usually has values equal to 50% (i.e. half the safety speed). This
value can be changed to adapt the standard manual movement speed to the individual
programming requirements.

HS-0-C5E-USO_33.fm
38 10/0713
Robot motion in Programming mode

Before moving in Cartesian mode (Tool, Uframe, Base) the correct definition should be
checked of the reference systems, especially the declaration of the tool frame through
the $TOOL variable. A wrong description of the tool causes errors in learning the points
and does not keep the TCP position unchanged during orientation movements. A good
method to check the correctness of $TOOL is to check that the TCP remains fixed while
changing the orientation of the tool.

The procedure for arm manual movement of a robotic cell varies slightly according to
the cell controller configuration. The following paragraphs describe the main details for
each typical situation.

4.5 Manual motion in WRIST_JNT mode


In Cartesian mode movement (Tol, Usr, Bas) of certain types of arms, it is more
convenient to change the orientation of the tool to a mode that does not rotate around a
Cartesian axis, but moves the axes of the robot wrist directly (the wrist axes, for a 6-axis
robot are the last three). This is useful for machines with less than 6 axes since their
capacity to rotate the tool is limited and it is not possible to obtain exactly what is
required. It is also useful when passing through singularity point. For some types of robot
the WRIST_JNT mode may not exist.
The mode on the Teach Pendant, can be selected from the Motion page, Basic
sub-page, COORD field. The WRIST_JOINT mode changes the behaviour of the BASE,
TOOL and UFRAME modes; the corresponding texts change to WR-BASE, WR-TOOL
and WR-UFRAME. The Joint mode remains unchanged.
The difference in the robot movements is most evident regarding the keys to change the
geometry, that is, keys 4+/-, 5+/- e 6+/-. In WR-BASE, WR-TOOL e WR-UFRAME
modes, these keys are associated directly to each wrist axis and when one of these keys
is pressed the corresponding axis is moved leaving the positions of the other wrist axes
unchanged. This operation, however holds the TCP position because the first three axes
move to offset the change in orientation. It is to be noted that if the robot has only 2 wrist
axes (for example 4 and 5), only keys 4+/- and 5+/-, can be enabled, whereas only key
4 will be enabled for a four-axis robot. For the 1X+/-, 2Y+/- and 3Z+/- keys the difference
is less obvious: the movement is linear in the direction required but the geometry of the
tool is not constant along the path since the wrist axes are not moved.

4.6 Manual motion of a single arm system


To execute the manual movement of a single arm it is sufficient to set the status selector
switch on T1, choose the most appropriate mode and press the ‘+/-’ keys, keeping the
Enabling Device on the Teach Pendant pressed.

4.7 Manual motion of auxiliary axes, slides and


rotating columns
The auxiliary axes can be added to an Arm in order to move different types of

HS-0-C5E-USO_33.fm
10/0713 39
Robot motion in Programming mode

positioners. Another example of auxiliary axis is the motor driven spot welding gun.
An example of an integrated auxiliary axes group is a roto-translating column or a
gantry.
Jogging an auxiliary axis is usually only possible in joint mode (JOINT) using the
corresponding AUX A/AUX B + e - keys.
The manual movement of an auxiliary axis is usually only possible in joint mode (JOINT)
using the corresponding AUX A/AUX B + e - keys.
To associate the auxiliary axes to AUX A and AUX B keys, it is needed to open the
Motion Page - subpage COOP - section AUX Jog, on the Teach Pendant.

For further information, please see C5G Control Unit Use - chp. Motion Page - par.
COOP (optional), AUX JOG section).

If the Teach Pendant is the wireless version (WiTP), the AUX hardkey is also available.
However, if the auxiliary axis moves a slide, a column or a built-in gripper, it can be
moved also in Cartesian modes (BASE, TOOL and UFRAME) using the same keys as
for JOINT mode.
Jogging in cartesian mode, allows to move the integrated axis without moving the TCP
(thus, the robot joints can move and follow the auxiliary axis/axes motion, in order not to
move the TCP from its initial position).

Note that when teaching positions for auxiliary axes, it is recommended to use
XTNDPOS.

4.8 Manual motion with Controller multi-arm


configuration
In the case of Controller multi-arm configuration, it is necessary to select the arm to be
moved using the Motion page on the Teach Pendant and checking the current value
on the status bar.
It is also possible to activate two arms at the same time that belong to two different
machines. To do this it is necessary to be in DRIVE OFF status and change the current
arm on the Motion page, Basic sub-page (Arm field).
For manual movement of integrated arms (a particular application of multi-arm system)
see the specific Chap. Motion Control.

4.9 Motion instruction in programming status


To program robot movements requires a certain knowledge of the C5G system and the
PDL2 programming language. However, before creating an actual program, some
simple moves can be made with the immediate execution of an instruction. To do this,
the system has to be in programming state with the EXECUTE command called (from
Service page of the Teach Pendant) that allows the immediate execution of an
instruction.

HS-0-C5E-USO_33.fm
40 10/0713
Robot motion in Programming mode

In its most simple form, the instruction consists of the key words MOVE TO followed by
the destination position. The most useful move instruction in the first stages of use is:
MOVE TO $CAL_SYS
This produces a movement of each axis to its calibration position. In its more complete
form the arm to be moved, the type of path and the destination can be selected.
The arm is assigned by the key word ARM (num_arm) that is placed immediately after
the word MOVE. The definition can be omitted if the system has only one arm (for
example an NJ4 robot (6 axes) is one arm only) or if the default arm predefined by the
system is to be moved.
The type of path may be joints, linear or circular and is described by the predefined
constants JOINT, LINEAR and CIRCULAR respectively (see the Chap. Motion Control
for further details). If the type of trajectory is not indicated, the value defined in the
$MOVE_TYPE system variable is valid, that is usually set at JOINT by the system.
The destination points are typically learnt inside a program, but they can also be
assigned directly in the instruction line of EXECUTE. Two ways to assign the destination
point that are most useful for installation and maintenance are given below. A Cartesian
point can be assigned by the built-in POS that allows, as parameters, the three
co-ordinates x, y and z where the TCP is to be taken, three angles for tool orientation
and a configuration string. All the positions of this type are called POSITION and are
always referred to the reference systems; the configuration string can usually be left
empty. The following is a valid position that defines a point at 100 mm from the user
reference in direction z: POS (0,0,100,0,0,0,’’). For further information see the
Chap. Motion Control and the PDL2 Programming Language manual. A destination
point can also define the position to be reached by each arm axis (including auxiliary
axes). To do so, write the values separated by a comma (in the correct order) and
enclose the complete declaration in a brace. A missing value leaves the position of the
corresponding axis unchanged. The following is a joint type position, that requires axis
1 to move 10 degrees from the zero position, leaves axis 2 stationary, takes axis 3 to
-30 degrees and leaves the wrist unchanged: {10, ,-30}.
Some examples follow for valid movement instructions (for further information see the
PDL2 Programming Language Manual).

MOVE LINEAR TO POS(100,200,300,0,0,0,’’) linear movement of pre-defined arm on a point of


Cartesian co-ordinates x=100, y=200 and z=300 and
the frame of the tool with the same orientation as the
user frame
MOVE JOINT TO POS(0,0,0,0,180,0,’’) joints type movement of the predefined arm on a point
of Cartesian co-ordinates x=0, y=0 and z=0 and axis z
of the tool frame facing the opposite direction to the z
of the user reference
MOVE JOINT TO {0,0,0,0,0,0} joints type movement of the first six axes of the default
arm on the zero positions
MOVE JOINT TO {, , , , ,90} movement of axis 6 only of the default arm on the
position of 90 degrees
MOVE LINEAR TO {45} linear movement that brings the arm to a position that
differs from the initial position for axis 1 only, that is
brought to 45 degrees. During the linear movement of
the TCP all the axes of the arm can move
MOVE ARM[1] LINEAR TO POS(100,100,100,0,0,0,’’) linear movement of arm 1 that takes the TCP to a
certain Cartesian position in relation to the user frame

HS-0-C5E-USO_33.fm
10/0713 41
Robot motion in Programming mode

MOVE ARM[2] JOINT TO POS(0,0,0,0,180,0,’’) joints movement of arm 2 that brings the TCP to a
certain Cartesian position in relation to the user frame
MOVE ARM[1] LINEAR TO {0,0,0, , ,} linear movement that brings the first arm to a Cartesian
position where the first three axes have no value,
whereas the wrist axes return to the initial position.
During the TCP linear movement all the axes of the
arm can move
MOVE ARM[2] JOINT TO {-90} movement of second arm that moves only axis 1 to the
position of 90 degrees in negative direction
MOVE CIRCULAR TO POS(100,100,0,0,0,0,’’) VIA movement of pre-defined arm that joins the starting
POS(0,200,0,0,0,0,’’) point to POS (100,100,0,0,0,0,’’) with a circumference
that passes through POS (0,200,0,0,0,0,’’)

Before executing a movement it is better to check the correct definition of the reference
systems, especially the declarations of the tool frame and the user reference ($TOOL,
$BASE and $UFRAME). These declarations can only be ignored in the case of joint
movements on joint points, for example MOVE JOINT TO $CAL_SYS now MOVE TO
{0,90,-100,20,20,200}, or MOVE TO JOINTPOS. In all other cases the consequences
could be dangerous with risks for the personnel and for the equipment. In particular if
the description of the tool is not correct (wrong $TOOL) the TCP will not reach the
required point, nor will it execute a correct linear or circular path. Regarding the
description of the user frame ($UFRAME) it is important to check that, at the moment
the movement is executed, this is identical to that which was active when the point was
stored. Otherwise the positioning will be different to that stored. However, the same
paths can be executed again with different $UFRAME values, since this performance is
necessary for some applications that require a specific shifting of the whole program
inside the work space (palletizing applications).
It is also necessary to always check the correct definition of the load used, regarding the
weight, centre of gravity and inertia. This data can be automatically calculated by the
Controller, given a Tool (also a Tool plus a part), applying the Payload identification
(optional function) included in the TO_SET application (that can be activated from the
Teach Pendant, Setup page, ToolFrame sub-page).
The verification checks that the recorded load data corresponds with the
$TOOL_MASS, $TOOL_CNTR and tool $TOOL_INERTIA[1..6] variables currently in
use.

HS-0-C5E-USO_33.fm
42 10/0713
Motion Control

5. MOTION CONTROL

5.1 Overview
This chapter contains the description of the C5G Robot Control Unit motion
environment, with the exception of manual handling (Teach Pendant jog keys) which is
described in the Chap. Robot motion in Programming mode, and for the optionals that
are dealt with further on in other chapters of this manual.
Information is supplied about the following topics:
– Frames of Reference and coordinates transformation
– Trajectory and Trajectory Recovery
– Position Checking
– Speed Control
– Acceleration and Deceleration
– Motion termination
– Process Resume
– Continuous Motion
– Remote Tool System;
– Integrated Movement;
– Palletizing functionality (optional feature).
Current chapter contains many references to predefined variables and instructions of
PDL2 language. For further information, refer to PDL2 Programming Language
Manual.

5.2 Frames of Reference


For our purposes, the following terminology should be defined.
Cartesian frame of reference is a geometrical concept that represents an object
positioned in space. For example, the corner of a table can be the frame of reference
that represents the table. The same can be done with a book, as well as with a welding
gun mounted on the robot flange.
A Coordinate transformation represents the position of one frame of reference with
respect to another. It is described by a POSITION variable. For example, if a table is
located in a room then the position of the table with respect to the room is expressed by
the POSITION p_table, which describes the coordinate transformation between the two
frames of reference. The coordinate transformation can be used to compute the position
of an object with respect to another coordinate frame. For example, a book whose
position with respect to the table corner is p_book, is located at the position
(p_table:p_book) with respect to the corner of the room. The (:) is the relative position
operator used to compose the effect of different coordinate transformations. See Data
Representation chapter of PDL2 Programming Language manual for further

pr-0-0-gpr_04.fm
09/0313 43
Motion Control

information.

5.2.1 System Frame of Reference


C5G Controller Unit has got three system variables ($BASE, $TOOL and $UFRAME)
which allow to describe the coordinates tranformations. Before describing the meaning
of such transformations, it is necessary to define some frames of reference.

World Frame The factory plant frame of reference with respect to which all
machines are positioned
Base Frame The frame located on the robot base
User Frame The frame located on the workpiece
Flange Frame The frame located on the robot flange
TCP Frame The frame located on the tool top

The $TOOL variable describes the position of the TCP frame with respect to the flange
frame; the $BASE coordinate transformation describes the position of the base frame
with respect to the world frame; the $UFRAME transformation describes the position of
the workpiece with respect to the world. The POS transformation represents the taught
point P that will be reached by the TCP during the execution of the program. Note that
all the taught POSITIONs are defined with respect to the user frame of reference
(defined by $UFRAME).
To better understand, suppose that the corner of the room is the world frame, and a
robot is located beside a table as shown in the following picture Fig. 5.1 - System
Frames of Reference and Coordinates Transformation.

Fig. 5.1 - System Frames of Reference and Coordinates Transformation

1 - Flange frame 2 - Tool frame 3 - Recorded position


4 - User frame 5 - Base frame 6 - Boundary frame

Suppose further that the robot has a pen mounted on the flange and it has to write
COMAU on the table. $BASE defines where the robot is located, the $TOOL
transformation describes the pen, and the $UFRAME transformation defines the

pr-0-0-gpr_04.fm
44 09/0313
Motion Control

position of the table with respect to the room.


These system frames will simplify some operations. For example:
– if the robot were picked up and placed at the opposite side of the table, it would be
enough to redefine $BASE and restart writing without modifying any point;
– if the pen were replaced with a bigger one, it would be enough to redefine $TOOL
and restart writing without modifying any point;
– if the table were moved inside the room, it would be enough to redefine $UFRAME.
Note that in some applications $BASE and $UFRAME can be left equal to zero: this
means that the world frame and the workpiece frame are located at the base of the robot
and all taught POSITIONs are referred to the base of the robot. On the contrary, the
$TOOL transformation must always be correctly defined to achieve the desired path of
the TCP (Tool Center Point) along the trajectory.

5.2.2 Base System of Reference definition


The $BASE predefined variable describes the position of the base of the robot in relation
to the external world.
It is useful to offset repositioning of the robot inside the cell or to repeat the same
program on the same part but with different robots. Also, a well-defined base reference
simplifies calculation of points (POSITION) during off-line programming.
To properly calculate $BASE, the POS_FRAME function can be used as follows (the
program must be run in a programming environment with Step mode set to Statement):

PROGRAM setbase
VAR corner, x, xy : POSITION
BEGIN
$UFRAME := POS (0,0,0,0,0,0,")
$TOOL := ... -- correttamente definito
-- Move the TCP to three points of the part using the jog keys
and store
-- tasti di jog e memorizzare
-- the corner, x and xy POSITIONS pressing the MOD key of the
TP.
-- Then perform the following instruction.
$UFRAME := POS_FRAME(corner, x, xy)
END setbase

5.2.3 Flange Tooling definition


Cartesian motions (straight lines for example) are defined for the TCP (tool centre point)
only. For example, when a straight line motion of the TCP involves large changes in tool
orientation during the motion, the tool flange does not necessarily move in a straight line.
Therefore, in order for Cartesian motions to work properly, the position (both location
and orientation) of the TCP, with respect to the tool flange, must be properly defined.
Proper definition of the TCP orientation is also necessary for the approach vector used in
MOVE NEAR and MOVE AWAY statements to be properly defined.
The position of the TCP is defined by defining a transformation from the tool flange
frame of reference to the TCP frame of reference. The predefined variable, $TOOL,
defines this transformation. The position of flange frame of reference is fixed for each

pr-0-0-gpr_04.fm
09/0313 45
Motion Control

model of robot and is documented in the hardware manual for the specific robot. It is the
operators responsibility to define $TOOL for the specific tooling to be mounted on the
flange.
Two sets of tool parameters define the $TOOL transformation:
– Three tool dimensions define the location component of $TOOL. These values,
measured in millimeters, represent the tool center point (TCP) offset with respect
to the flange center;
– Three tool rotations define the orientation component of $TOOL. These values,
measured in degrees, represent three rotation angles called Euler angles.

5.2.3.1 TCP Offset definition


The offset for tool dimensions can be measured on the arm itself or calculated
theoretically based on the tool design. The parameters can vary according to the tool
assembly position in that they must be defined according to the tool z axis (ref. z
Tool), commonly referred to as the approach vector.
To measure the tool dimensions, proceed as follows:

a. Begin with no tools on the robot. Assign zero values to all six tool parameters of
$TOOL.

$TOOL := POS (0, 0, 0, 0, 0, 0, ‘ ‘)

b. Identify x, y, and z axes directions of the tool. (Note: For SMART robot, base axes
are parallel to tool axes when the robot is pointing upward and small axes are at
mid-travel).

c. Move the robot to a known position, e.g. the calibration position (Fig. 5.2 shows the
calibration position for SMART robots). Note that for some robot models, the
calibration position could be different than the shown one.

d. Check the direction of the three tool axes by jogging the robot using the TOOL jog
coordinate type.

e. Mount the tool and measure the tool centre offsets (positive or negative) with
respect to the flange centre along all three axes. Measurements should be in
millimetres.

f. Assign measured values to $TOOL using a PDL2 assignment statement:

$TOOL := POS (x, y, z, e1, e2, e3, ‘ ‘ )

pr-0-0-gpr_04.fm
46 09/0313
Motion Control

Fig. 5.2 - Known position

5.2.3.2 Calculating the Rotation Angles


Rotation values are independent from offset values and must be calculated after the
offset values have been assigned. Depending on the application, the rotation values can
be omitted. In this case, tool orientation will be along an axis parallel to the flange axis
that starts at the TCP. The rotation values are positive for counterclockwise rotation with
the rotation axis pointed toward the observer. These values can be calculated using one
of the two methods described below.

5.2.3.2.1 FIRST METHOD


Calculate three rotations that will align the flange z axis with the tool z axis. The
rotations, which correspond to Euler angles, are designated (e1) rotation around z, (e2)
rotation around y, and (e3) rotation around the new z.
Note that:
– it is not possible to rotate axis x;
– rotation around y must be between 0 and 180 degrees;
– rotation around z must be between -180 and 180 degrees.
Assign the rotation values to $TOOL using the PDL2 assignment statement:
$TOOL := POS (x, y, z, e1, e2, e3, ‘ ‘)
Some example calculations follow. In the following diagrams, u indicates the tool z axis.

Example A
Tool z axis (u) coincides with axis z of the flange.
In this case no rotation assignment is required:
(e1, e2, e3) = (0, 0, 0)

pr-0-0-gpr_04.fm
09/0313 47
Motion Control

Example B
Tool z axis (u) coincides with axis y of the flange.

The following rotations should be performed:

a. Rotate 90 degrees around axis z

b. Rotate 90 degrees around axis y.

c. Rotate 180 degrees around the new axis z.


The tool z axis (u) now coincides with the flange z axis.
The rotation angles (e1, e2, e3) are (90, 90,180).

Example C
Tool z axis (u) is at 90 degrees with respect to the flange z
axis in the direction -y.
Rotation angles are (-90, 90, 180).

pr-0-0-gpr_04.fm
48 09/0313
Motion Control

Example D
Tool z axis (u) is at 90 degrees with respect to the flange z
axis in the direction x.
Rotation angles are (0,90,180).

Example E
Tool z axis (u) is at 90 degrees with respect to the flange
z axis in the direction -x.
Rotation angles are (180, 90, 180).

5.2.3.2.2 SECOND METHOD


Use the three rotation controls on the teach pendant to move:
– the Tool z axis parallel and in accordance with the base z axis;
– the axis which is to become Tool axis x parallel and in accordance with the base x
axis of the user frame.
After these two moves, the final Tool axis y is consequently parallel with the base y axis.
The angle parameters alpha, beta, epsilon can be read on the Teach Pendant Motion
Page - Basic subpage - ARM_POS section (System Command: DAP).
Tool parameters will be given by:
– rotation 1 = 180 degrees - epsilon (-360 degrees);
– rotation 2 = beta;
– rotation 3 = 180 degrees - alfa (-360 degrees).
(It is needed to add (-360 degrees) if the value of rotation exceeds 180 degrees).
The angle values to be assigned are obtained by rounding off those calculated (typically
rounding off is to 0, 90, or 180 degrees).

The TCP is calculated at the tool closing point. Any safety flange logically belongs to the
tool and therefore increases the z offset.

5.2.3.3 User System of Reference definition


The $UFRAME predefined variable can be used to describe the position of the
workpiece with respect to the world. It is useful to compensate the relocation of the
workpiece or to execute the same program on workpieces in different positions. Besides
a well defined user frame can simplify the computation of positions when doing an

pr-0-0-gpr_04.fm
09/0313 49
Motion Control

off-line.
To compute the correct value of $UFRAME, the POS_FRAME built-in can be used as
follows (the program should be executed in the PROGRAM EDIT environment with the
Step modality set to Statement):

PROGRAM setframe
VAR corner, x, xy : POSITION
BEGIN
$UFRAME := POS(0,0,0,0,0,0,")
$TOOL := ... -- correctly defined
-- Jog the TCP upon three point on the workpiece and teach the
POSITIONs
-- corner, x and xy pressing the MOD key on the TP.
-- Then execute the following statement.
$UFRAME := POS_FRAME(corner, x, xy)
END setframe

5.3 Trajectory
It represents an Arm motion from an initial position to a final position.
The motion trajectory between two taught positions is generated by interpolating various
sets of variables from their initial values at the start position to their final values at the
destination position. The predefined variable $MOVE_TYPE indicates the type of
interpolation to be used. It is a program-specific variable (one for each active program).
The predefined constants JOINT, LINEAR, or CIRCULAR can be assigned to
$MOVE_TYPE. The trajectory can be also expressed in the move statements by
assigning the reserved words JOINT, LINEAR or CIRCULAR to the MOVE statement.
The trajectories can be classified as follows:
– joint trajectory: JOINT
– linear trajectory: LINEAR
– circular trajectory: CIRCULAR.

5.3.1 Joint Interpolation


During joint interpolation ($MOVE_TYPE := JOINT or MOVE JOINT TO), the joint
angles of the arm are linearly interpolated from their initial to final values. All axes start
moving at the same time and reach their destination at the same time. The path followed
by the tool centre point (TCP) is not predictable, although it is repeatable.
Joint interpolated movements between two positions are always possible.

5.3.2 Linear Interpolation


During linear interpolation ($MOVE_TYPE := LINEAR or MOVE LINEAR TO), the TCP
moves in a straight line from the initial position to the final position. The orientation of the
tool also changes from the initial position to the final position according to the mode
defined by the $ORNT_TYPE variable. This specific program variable can have the
values of the following predefined constants: RS_WORLD, RS_TRAJ, EUL_WORLD,
WRIST_JNT.

pr-0-0-gpr_04.fm
50 09/0313
Motion Control

For further information refer to the par. 5.3.4 Orientation Evolution during Linear or
Circular movements on page 51 section.

5.3.3 Circular Interpolation


During circular interpolation ($MOVE_TYPE := CIRCULAR or MOVE CIRCULAR TO),
the TCP follows a circular arc from the initial position to the destination. An additional
position, called the VIA position, must be specified to define the arc. Only the location
component of the VIA position is used; its orientation does not affect the motion.
As for linear interpolation, the $ORNT_TYPE predefined variable indicates the type of
evolution of attitude must be performed.

5.3.4 Orientation Evolution during Linear or Circular


movements
The orientation of the tool during linear and circular movements evolves from the initial
position to the final position in the manner indicated by the $ORNT_TYPE variable.
Possible values of this specific variable of the program are as follows:
– RS_WORLD (two-angles related to the world frame)
Orientation interpolation is done by linearly interpolating the values of two rotation
angles, tool rotation and tool spin. The tool rotation angle is the angle about the
common normal between the beginning tool approach vector and the destination
approach vector. The tool spin angle is the angle about the approach vector from
the beginning position to the destination position. The evolution is related to the
World frame independently from the trajectory.
RS_WORLD is the default value for $ORNT_TYPE.
– RS_TRAJ (two angles related to the trajectory)
Orientation interpolation is done in the same way than RS_WORLD but the rotation
and spin angles are related to the trajectory. This is particularly useful during
circular trajectory having an angle grater than 180 degrees when the user wants to
maintain the tool orientation constant with respect to the trajectory. During linear
motions the orientation evolution is the same than RS_WORLD.
– EUL_WORLD (three-angle)
Orientation interpolation is done by linearly interpolating the values of the three
Euler angles of rotation, E1, E2, and E3.
– WRIST_JNT (wrist-joint)
Orientation interpolation is done by using a combination of joint and linear
interpolation. This permits the tool to move along a straight line while the wrist joints
are interpolated in joint coordinates. The starting and ending orientation will be
used as taught, but because of the joint interpolation, the orientation during the
movement is not predictable, although it is repeatable. For example, using either
EUL_WORLD or RS_WORLD, if the beginning and ending orientations are the
same, then the orientation of the tool will remain fixed during the motion. However,
with WRIS_JNT orientation interpolation this is not guaranteed. However,
WRIST_JNT orientation control allows for much smoother motion near wrist
singularities.

pr-0-0-gpr_04.fm
09/0313 51
Motion Control

5.3.5 Attitude Flags During Linear and Circular Movements


During Cartesian trajectories (LINEAR and CIRCULAR) the attitude flags of the starting
and final points of a movement must correspond, otherwise the movement will not be
executed. Attitude flags signify the S, E, W, A and B parts of a Cartesian position (see
the PDL2 Programming Language Manual for further details).
– S indicates that the WCP (Wrist Center Point) is in the zone lying behind the plane
defined by the first and the second axes.
– E indicates that the WCP is in the zone lying behind the extension of the second
axis;
– W indicates that the value of the fifth axis is negative.
– A indicates that the TCP (Tool Center Point) is in the zone lying behind the
extension of the second axis;
– B indicates that the TCP (Tool Center Point) is in the zone lying behind the plane
defined by the first and the second axes.
The only exception to this is when passing over a singularity point, in which the W flag
is reversed by the system software.
It is, however, possible to execute the movement even if the flags do not correspond:
set the $CNFG_CARE predefined variable to FALSE to make the flag of the final point
match that of the starting point.
This setting is mainly used when mixing movements that use JOINTPOS type variables
and POSITION type variables with values that have been set directly from the PDL2
program and not taught using the REC key on the teach pendant.
If the starting point is a JOINTPOS, the value of the configuration string is unknown and
it is therefore useful to set the $CNFG_CARE variable to FALSE.

5.3.6 Turn Flag and minimum path


Turn flags (T1, T2, T3, T4) are part of the configuration string and are associated with
axes capable of performing multi-turns, i.e. that can rotate by more than 360 degrees
($STRK_END_P[axis] - $STRK_END_N[axis] > 360) (for further details also see the
PDL2 Programming Language Manual).
A Cartesian trajectory (LINEAR or CIRCULAR) generally follows the shortest path for
the joints and the configuration string of the final point that has been reached may
therefore differ from that present in the movement instruction. If so, the system will
execute the movement in any case, unless the predefined variable, $TURN_CARE, has
been set to TRUE; in that case, an error message will indicate the difference in the
number of turns.
POSITION type variables that were taught using a particular $UFRAME may have a
different number of turns when the $UFRAME is changed. For instance, if a P0 point
was taught with axis 4 at 170 degrees and P1 with axis 4 at 179 degrees, the number of
turns will not be included in the position variables (configuration string empty ‘’‘’).
However, if a slight change is made to $UFRAME, the joints associated with P0 and P1
may change. For example, P0 may now have axis 4 at 172 degrees and P1 have axis 4
at 181 degrees. In that case, the shortest path is from 172 to 181 degrees, but in order
to move axis 4 to 181 degrees, position P1 should have flag T1:1. However, there is no
turn flag in the P1 configuration string and therefore, in order to avoid an error on the
LINEAR MOVE from P0 to P1 with a new $UFRAME, $TURN_CARE must be set to

pr-0-0-gpr_04.fm
52 09/0313
Motion Control

FALSE.
A joint trajectory (JOINT) or a Cartesian movement with WRIST_JNT evolution, effected
on points declared as POSITIONs, sets a path that follows the evolution of the joints,
without considering the shortest or longest route. To follow the shortest route (<180
degrees), set the $JNT_MTURN variable to FALSE.
Note that the $JNT_MTURN variable is ineffective in joint movements on points
declared as JOINTPOS.

5.4 Position Checking


There are two functions, called ON TRAJECTORY and ON POS, that can be used to
verify the robot’s position in relation to the programmed trajectory or to predefined
positions. This is mainly used when monitoring the line from external devices, such as a
PLC. By means of appropriate calls to the built-in routines, ON_TRAJ_SET,
ON_JNT_SET and ON_POS_SET, it is possible to define the bits of analogue ports (e.g.
$WORD) that will be set to 1 when a predefined position is reached or during the robot
movement along the programmed trajectory.

5.4.1 On Trajectory Function


This function, which is always enabled, is used to verify, at any time, whether the robot
is on the trajectory programmed of the PDL2 program that is running.
$CRNT_DATA[arm].OT_POS indicates the robot’s position along the programmed
trajectory. The $CRNT_DDTP[arm].OT_JNT variable includes information concerning
any auxiliary axes that may be present. $CRNT_DATA[arm].OT_COARSE is TRUE
when the robot is on the programmed trajectory and FALSE if that is not the case.
For safety reasons, the deviation between the current position of the robot and the
$CRNT_DATA[arm].OT_POS position is calculated by taking into account the threshold
in millimeters in relation to the flange ($ARM_DATA[arm].OT_TOL_DIST) and the
threshold in degrees in relation to the orientation of the flange
($ARM_DATA[arm].OT_TOL_ORNT). In case of a very long tool (for instance, 1 meter
in the tool’s Z direction) and if the robot has stopped in correspondence with
$CRNT_DATA[arm].OT_POS, only a slight rotation of the tool is necessary in order to
provoke a significant flange movement, so that the $CRNT_DATA[arm].OT_COARSE
variable is set to FALSE. In case of rotating auxiliary axes, threshold
$ARM_DATA[arm].OT_TOL is used. In case of traversing auxiliary axes, threshold
$ARM_DATA[arm].OT_TOL_ORNT is used.
If the arm includes integrated auxiliary axes, in case of jog movements in joint mode, all
the axes that have been enabled, including the auxiliary axes, contribute to the
modification of the Cartesian position and result in the arm moving away from the
trajectory ($CRNT_DATA[arm].OT_COARSE = FALSE). In case of jog movements in
Cartesian mode (Base, Tool, etc.) the movement of the auxiliary axis is compensated
by the robot’s axes in order to maintain the Cartesian point; however, as the entire
configuration of the arm axes is modified, the arm also moves away from the trajectory
in this case ($CRNT_DATA[arm].OT_COARSE = FALSE), extending the concept of
position on the trajectory to the extended position.
If the arm includes auxiliary axes that are not integrated, in case of jog movements in
joint mode, the axis does not modify the Cartesian position, but the overall configuration

pr-0-0-gpr_04.fm
09/0313 53
Motion Control

of the arm is modified and the arm moves away from the trajectory
($CRNT_DATA[arm].OT_COARSE = FALSE). In case of jog movements in Cartesian
mode, the auxiliary axis cannot be moved and the arm behaves in the same way as the
6 axes robot.
It is always possible to return to the trajectory ($CRNT_DATA[arm].OT_COARSE =
TRUE) by executing a movement on the $CRNT_DATA[arm].OT_JNT variables (or
$CRNT_DATA[arm].OT_POS variables, for robots with no auxiliary axes).
Example:
MOVE TO $CRNT_DATA[arm].OT_JNT
oR
MOVE TO $CRNT_DATA[arm].OT_POS
WITH $TOOL=$CRNT_DATA[arm].OT_TOOL,
WITH $UFRAME = $CRNT_DATA[arm].OT_UFRAME
ENDMOVE
The presence of a Remote Tool does not affect functionality. When the program is
deactivated, the $CRNT_DATA[arm].OT_COARSE variable is reset. See following
Tab. 5.1 - On Pos and On Trajectory table.
This function is not available on the following machine types: robots with active
kinematic compensation (file .ROB in RD), robots with conveyor tracking, enabled
cooperative movement.

When the CNTRL C key is pressed, to interrupt the execution of a NON movement
instruction of a program open in the EZ or PROGRAM EDIT or MEMORY DEBUG or
IDE environment, the $CRNT_DATA[arm].OT_COARSE flag will still be set to TRUE
even if the instruction that was interrupted is between two FLY movements. If the user
then moves the cursor onto a specific instruction from which he wishes to continue to
run the program, skipping some programmed movements, this could also damage the
robot and/or the start of the work cycle (executed in Remote or Local mode).
Responsibility for any damage resulting from such actions lies with the user in charge of
operating and controlling the cell.

For further details related to the $OT_xxx system variables and the ON_TRAJ_SET
built-in routine, please refer to the PDL2 Programming Language Manual.

5.4.2 On Position (ON POS)


By means of this function, it is possible to verify, at all times, whether the robot’s Tool
Center Point (TCP) corresponds to a specific predefined position, such as the Home
position, the Tip-dressing position for SPOT applications or the Service position. The
predefined positions must be stored:
– in the $OP_JNT field if the auxiliary axes, or some of these (see predefined
variable $ON_POS_TBL[index].OP_JNT_MASK), must also be controlled;
– in the $OP_POS field if only the Cartesian position is concerned.
This information is primarily used to communicate to external devices, such as a line
PLC, that the robot is in the aforesaid positions.
To make the On Pos function operational, each time the control unit is restarted, the
application program must run the following sequence of operations in the order set out
below:
– Initialize the predefined fields with the OP_ prefix, in the $ON_POS_TBL table.

pr-0-0-gpr_04.fm
54 09/0313
Motion Control

– Run the built-in procedure ON_JNT_SET or ON_POS_SET to define which port


and which bit are to be assigned upon reaching the main positions.
– Execute ON_POS(ON) to enable the function, which will remain enabled until the
subsequent ON_POS(OFF) is executed on the same item of the $ON_POS_TBL
or at the subsequent system restart.
For further details related to the $ON_POS_TBL and $OP_xxx system variables, the
ON_JNT_SET, ON_POS_SET and ON_POS built-in routines, the CONDITION events,
please refer to the PDL2 Programming Language Manual.
This service is disabled in the case of: robot with active kinematic offset (file .ROB) in
UD, robot with cooperative or conveyor tracking enabled.

5.4.2.1 Example of On Pos and On Trajectory


In order to summarize the behavior of the system, let us suppose that a program being
executed is interrupted:
– in a configuration in which the arm is on the trajectory;
– on a predefined position;
– on a predefined joint position for all axes of the arm (the mask of the joints on
ON_JNT_SET corresponds to the $JNT_MASK).
Let us suppose we wish to perform an arm movement, in jog mode, exceeding the
predefined threshold:

Tab. 5.1 - On Pos and On Trajectory


On Trajectory On Pos con JOINTPOS On Pos con POSITION
($OP_JNT) ($OP_POS)
Value of: Value of: Value of:
$CRNT_DATA[ ].OT_COARSE $ON_POS_TBL[ ].OP_REACHED $ON_POS_TBL[ ].OP_REACHED
Initial condition TRUE TRUE TRUE
Movement of robot FALSE FALSE FALSE
axis in joint mode
Movement of FALSE FALSE FALSE
integrated auxiliary
axis in joint mode
Movement of FALSE FALSE TRUE
non-integrated
auxiliary axis in joint
mode
Movement in FALSE FALSE FALSE
Cartesian mode with
reference to X, Y, Z
and/or E1, E2, E3
Movement in FALSE FALSE TRUE
Cartesian mode of
integrated auxiliary
axis
Deactivation of FALSE TRUE TRUE
movement program

pr-0-0-gpr_04.fm
09/0313 55
Motion Control

5.5 Speed Control


Predefined variables are used to control the maximum or constant speed of a motion,
some of which are system-wide, some of which are program-specific, and some of which
are arm-specific. Two kinds of speed controls are used:
– absolute speed values or limit values, measured in normal speed units such as
radians per second or meters per second;
– override values that govern the absolute speed values, measured in percentage.
In the C5G system, not only speed can be controlled by the user, but also acceleration
and deceleration. Independent basic control values and overrides exist for acceleration,
speed, and deceleration. The basic and override values for acceleration and
deceleration are discussed in par. 5.6 Acceleration and Deceleration on page 61 in the
current chapter.

5.5.1 Speed Overrides


Speed override values govern (or override) the basic speed values (see description
par. 5.5.2 Cartesian Speed Control on page 57 section).
The speed overrides (percentage speed values) that apply to all motions are as follows:
– $GEN_OVR allows the operator to change simultaneously the acceleration, speed
and deceleration values of Motion programs. Since this influences the
acceleration, speed and deceleration values in a coordinated manner, the
trajectories are usually maintained (unless there are servo tracking errors) when
this variable is changed.
$GEN_OVR is an INTEGER type variable
It is common to the whole system and can be changed from the Teach Pendant.
The PDL2 programs can read it only.
– $ARM_OVR permits acceleration, speed, and deceleration of a specific arm to be
modified from within a program. Since it affects acceleration, speed, and
deceleration in a coordinated way, trajectory shapes are generally maintained
when this control is modified (except for differences in servo following errors at
different values of override).
$ARM_OVR is an INTEGER field of the system-wide array of structures,
$ARM_DATA[ ]. There is one $ARM_DATA structure per arm, and the ARM_OVR
field has a default value of 100%.
Note that if constant speed during transitions between continuous motions is more
important than constant trajectory, then $ARM_SPD_OVR or $PROG_SPD_OVR
should be used (acceleration and deceleration will be left at current values as these
speed overrides are reduced).
See section par. 5.10.1 Trajectory Shape During Continuous Motion on page 71 in
current chapter.
– $ARM_SPD_OVR permits the speed of a specific arm to be modified by a program.
Acceleration and deceleration are not affected. This implies that the shape of
continuous motion trajectories may change as this control is changed.
See section par. 5.10.1 Trajectory Shape During Continuous Motion on page 71 in
current chapter.
$ARM_SPD_OVR is an INTEGER field of the system-wide array of structures,
$ARM_DATA[].

pr-0-0-gpr_04.fm
56 09/0313
Motion Control

There is one $ARM_DATA structure per arm, and the ARM_SPD_OVR field has a
default value of 100%.
– $PROG_SPD_OVR permits speed of all motions issued from a specific program to
be modified by the program. Acceleration and deceleration are not affected.
This implies that the shape of continuous motion trajectories may change as this
control is changed.
It is a program-specific variable with a default value of 100%.
The total speed override for any motion for a specific arm is determined as follows:

total speed override[arm] = $GEN_OVR * $ARM_DATA[arm].ARM_OVR *


$ARM_DATA[arm].ARM_SPD_OVR * $PROG_SPD_OVR
$GEN_OVR and $ARM_OVR take effect during motions. That is, if either variable is
changed while a motion is in progress, the current motion will speed up or slow down
accordingly. However, a change in $PROG_SPD_OVR or $ARM_SPD_OVR will not
take effect until the next move statement within the program for which it is defined.
Also, please refer to par. 5.10.1 Trajectory Shape During Continuous Motion on page 71
section in current chapter, for a discussion of some more effects of such variables.
$ARM_SPD_OVR, $ARM_OVR, and other variables described in this chapter are fields
of the predefined system-wide array of structures, $ARM_DATA. The details of this
structure and how to reference fields within the structure are fully documented in the
chapter referring to the predefined variables of the PDL2 Programming Language
Manual.

5.5.2 Cartesian Speed Control


Under normal operation, the following two predefined variables govern the basic speed
of a Cartesian motion (linear or circular), with any type of orientation control.
– $LIN_SPD_LIM determines the linear speed. It is a variable for each Arm, whose
value depends on the Robot and cannot be modified by the User.
It is a REAL field of the system-wide array, $ARM_DATA[], which has one structure
for each arm. The default value for $LIN_SPD_LIM is machine dependent.
(normally: 1.5 m/s).
– $ROT_SPD_LIM determines the rotational speed. It is a variable for each Arm,
whose value depends on the Robot and cannot be modified by the User.
It is a REAL field of the system-wide array, $ARM_DATA[], which has one structure
for each arm. The default value for $ROT_SPD_LIM is machine dependent.
The actual speed of motion of a specific arm is determined by computing the maximum
of the motion times for each possible rotation at $ROT_SPD_LIM and the TCP
translation time at $LIN_SPD_LIM. For example, using RS_WORLD orientation control,
three evaluations are performed:
– the time for the approach vector to go from its initial orientation to final orientation
at $ROT_SPD_LIM;
– the time for the spin about the approach vector to go from its initial orientation to its
final orientation;
– the time for the TCP to translate from its initial location to its final location at
$LIN_SPD_LIM.
The component of motion that takes the longest to get from its initial to final location will
move at the programmed speed limit, reduced by the total override. All of the other

pr-0-0-gpr_04.fm
09/0313 57
Motion Control

components will move at lower than programmed limits, so that all components start and
stop at the same time.
If one of the rotations requires the most time, $ROT_SPD_LIM is used. If the translation
requires the most time, $LIN_SPD_LIM is used. The component moving at the
programmed speed limit is called the “maximum stressed” component, and it moves at
the “speed of maximum stress” or SMS.
Using this terminology, the Cartesian speed of a specific arm is determined as follows:

cartesian speed[arm] = SMS[arm] * total speed override[arm]


where SMS[arm] is $ARM_DATA[arm].ROT_SPD_LIM if rotation takes the longest, or
$ARM_DATA[arm].LIN_SPD_LIM if translation takes the longest. (See previous
par. 5.5.1 Speed Overrides on page 56 for a definition of “total speed override”).

5.5.2.1 Cartesian Speed Control Options


The process of determining which component governs Cartesian speed is called
preplanning. This occurs just before the motion actually occurs (i.e. after each MOVE).
It is possible to force the preplanner to pick a particular component of motion using the
predefined variable $SPD_OPT. It is a program-specific variable (each program can
have its own value) that can be assigned the following predefined constants:
– SPD_CONST is the default value. It moves the arm at constant speed with the
SMS being picked by the preplanner, as explained previously.
– SPD_JNT moves the arm along the requested Cartesian trajectory, at the
maximum speed of at least one joint. The TCP will not move at constant speed.
– SPD_LIN moves the TCP according to the requested $LIN_SPD, forcing the
rotation component to move in coordinate way.
Note that in this case, $LIN_SPD replaces $LIN_SPD_LIM in the speed
calculation. $LIN_SPD is a REAL field of the system-wide array of structures,
$ARM_DATA.
– SPD_ROT ($ORNT_TYPE=RS_WORLD) rotates the approach vector at
$ROT_SPD, forcing all other components to move in the same time.
Note that in this case, $ROT_SPD replaces $ROT_SPD_LIM in the rotation speed
calculations. $ROT_SPD is a REAL field of the system-wide array of structures,
$ARM_DATA.
– SPD_SPN ($ORNT_TYPE=RS_WORLD) spins the approach vector at
$ROT_SPD, forcing all other components to move in the same time. (See
SPD_ROT for explanation of $ROT_SPD).
– SPD_AZI ($ORNT_TYPE=EUL_WORLD) rotates the azimuth component at
$ROT_SPD, forcing all other components to move in the same time. (See
SPD_ROT for explanation of $ROT_SPD).
– SPD_ELV ($ORNT_TYPE=EUL_WORLD) rotates the elevation component at
$ROT_SPD, forcing all other components to move in the same time. (See
SPD_ROT for explanation of $ROT_SPD).
– SPD_ROLL ($ORNT_TYPE=EUL_WORLD) spins the approach vector at
$ROT_SPD, forcing all other components to move in the same time. (See
SPD_ROT for explanation of $ROT_SPD).

pr-0-0-gpr_04.fm
58 09/0313
Motion Control

– SPD_FIRST ($ORNT_TYPE=WRIST_JNT) rotates the first wrist joint at


$ROT_SPD, forcing all other components to move in the same time. (See
SPD_ROT for explanation of $ROT_SPD).
– SPD_SECOND ($ORNT_TYPE=WRIST_JNT) rotates the second wrist joint at
$ROT_SPD, forcing all other components to move in the same time. (See
SPD_ROT for explanation of $ROT_SPD).
– SPD_THIRD ($ORNT_TYPE=WRIST_JNT) rotates the third wrist joint (closest to
the tool) at $ROT_SPD, forcing all other components to move in the same time.
(See SPD_ROT for explanation of $ROT_SPD).
– SPD_AUX1 moves the first auxiliary axis at a constant speed while all other
components of the move will run at a reduced speed. If the joint is rotational, the
desired speed for the auxiliary axis should be specified by the predefined variable
$ROT_SPD. If the joint is linear the speed should be specified by the predefined
variable $LIN_SPD. If more than one auxiliary axis is present only one can move
at a constant speed and any other auxiliary axis will move at a reduced speed in
order to start and end the move at the same time.
If fly moves are executed when $SPD_OPT is set to SPD_AUXn then the auxiliary
axis will always run at a constant speed regardless of the value of $FLY_TYPE. If
$SPD_OPT is assigned a value of SPD_AUXn where n is an invalid auxiliary axis
then an error will be reported.
– SPD_AUX2 has the same effect as SPD_AUX1 except that the second auxiliary
axis is maintained at a constant speed.
– SPD_AUX3 moves the third auxiliary axis at a constant speed while all other
components of the move will run at a reduced speed so that the movement begins
and ends at the same time. All other effects of this option are the same as
SPD_AUX1.
– SPD_SM4C - the cartesian movement is performed using the Cartesian
SmartMove (optional feature).
For further information, see Chap.12. - SmartMove (optional feature).
In this case, the acceleration, speed and deceleration values aare automatically
calculated and it is impossible to set neither a translational ($LIN_SPD) nor a
rotational ($ROT_SPD) speed as maximum value.
In order to use such an option, it is needed to purchase the software option
SmartMove.
If the value of $SPD_OPT is not meaningful for the current trajectory type, the default
SPD_CONST is assumed. For example, specifying $SPD_OPT=SPD_SECOND has no
meaning if $ORNT_TYPE=RS_WORLD, so SPD_CONST would be used.
Changes to $SPD_OPT, $LIN_SPD, and $ROT_SPD only take affect at the beginning
of the next move. Changes do not affect the current motion of an arm.

5.5.2.2 Run-Time modifying the Linear Speed Override


It is allowed to run-time modify the TCP speed override, only if the following conditions
are satisfied:
– Cartesian movement
– the motion control type is $SPD_OPT := SPD_LIN.
Such conditions BOTH have to be satisfied, otherwise no run-time modifications are
allowed. Therefore, it is not possible to apply such a functionality to Arms which
CANNOT move with a cartesian motion.

pr-0-0-gpr_04.fm
09/0313 59
Motion Control

The predefined variable which allows to run-time modify the speed override, is

$LIN_SPD_RT_OVR
It is referred to $LIN_SPD predefined variable related to the motion, and indicates, as a
percentage, the new TCP speed to be used since the current motion.
The default value is 100: this means that the movement is performed at a maximum
speed equals to the $LIN_SPD. The maximum value to set $LIN_SPD_RT_OVR to, is
related to $LIN_SPD value, and is calculated as follows:

MAX = ($LIN_SPD_LIM / $LIN_SPD) * 100

which means that it allows to reach the cartesian speed limit for the robot.
The required modification is active since the current motion, and it is applied so as not
to cause sudden changing motion, even when the Run-Time Speed Override variations
are considerably high.

For run-time linear speed variations during synchronized motions, please see Chap.6. -
Synchronous Motion (optional feature) in current Manual.

5.5.3 Joint Speed Control


For joint interpolated motions, the actual motion speed for a specific arm is determined
by computing the maximum of the motion times for each joint travelling at its maximum
limit.
The predefined INTEGER array, $MTR_SPD_LIM[], defines the maximum speed of
each motor, which in turn defines the maximum speed of each joint. $MTR_SPD_LIM is
a field of the predefined system-wide array of structures, $ARM_DATA[].
Thus there is a value for each axis for each arm.
The speed override for each joint is determined by $JNT_OVR, which permits
acceleration, speed, and deceleration to be modified together by a program.
It is a field of $ARM_DATA and it is an INTEGER array of the system-wide array of
structures.
There is an override value for each axis of each arm. The default values are 100%.
The joint speed of a specific axis is determined as follows:

joint speed[axis] =
$MTR_SPD_LIM[axis] * gear ratio[axis] * $JNT_OVR[axis] *
total speed override[arm]
where “gear ratio” indicates the transmission ratio.
The joint that takes the longest to get from its initial to final position will move at the
above computed speed. All of the other joints will move at lower speeds, so that all joints
start and stop at the same time.

5.5.4 Manual Motion Speed Control


If movements are executed while the Control Unit is in PROGR status (status selector
switch on T1), a further $MAN_SCALE speed value is used, to keep the maximum
speed within the safety values. If the predefined variable $SPD_OPT is set to SPD_LIN,

pr-0-0-gpr_04.fm
60 09/0313
Motion Control

then the speed of the arm is determined by the value of the predefined variable
$LIN_SPD. If the value of $LIN_SPD is greater than 0.25 meters per second, then the
speed of the arm will be reduced to 0.25 meters per second. $MAN_SCALE is set at the
factory and cannot be changed by the Customer.

5.6 Acceleration and Deceleration


Acceleration and deceleration in the C5G controller are each broken into three phases,
a constant jerk phase, followed by a constant acceleration phase, followed by another
constant jerk phase.
See Fig. 5.3 - Speed and acceleration profiles.

Fig. 5.3 - Speed and acceleration profiles

1. speed
2. acceleration

Currently, C5G forces the acceleration profile to be symmetric and the deceleration
profile to be symmetric.
This means that the constant jerk phases during acceleration (T1 and T2) are the same
length and the constant jerk phases during deceleration (T3 and T4) are the same
length.
For joint interpolated motions, the total time of acceleration and deceleration is
established by two predefined variables:
– $MTR_ACC_TIME determines the total acceleration time in milliseconds;
– $MTR_DEC_TIME determines the total deceleration time in milliseconds.
These variables are INTEGER array fields of $ARM_DATA, one element for each axis
for each arm. For a joint interpolated motion, the time for the joint that takes the longest
to accelerate/decelerate to its final speed is picked for the time to use for all joints to
accelerate/decelerate. This maintains coordinated acceleration and deceleration.
For Cartesian motions, $LIN_ACC_LIM and $LIN_DEC_LIM are used in a similar way,
to establish the total time for acceleration/deceleration. However the units for these
variables are meters per second per second.
The percentage of acceleration time and deceleration time used in the constant jerk

pr-0-0-gpr_04.fm
09/0313 61
Motion Control

phases is determined by the predefined $ARM_DATA INTEGER array field, $JERK[],


as follows:
– $JERK[1] defines the percentage of the acceleration time in the constant jerk
phase (T1 + T2);
– $JERK[2] is reserved for future use;
– $JERK[3] is reserved for future use;
– $JERK[4] determines percentage of deceleration time in constant jerk (T3 + T4).
For example, if $JERK[1] is set to 40, then 20% of the time specified in
$MTR_ACC_TIME will be T1, 60% in constant acceleration, and 20% will be T2.
$JERK[] is read-only from a PDL2 program.

5.6.1 Acceleration/Deceleration Overrides


As with speed, acceleration and deceleration also have overrides.
As already explained in par. 5.5.1 Speed Overrides on page 56,
$GEN_OVR and $ARM_OVR not only affect speed, but also acceleration and
deceleration.
In addition, arm specific and program specific variables exist to further override
acceleration and deceleration. Such variables are arm or program specific:
– $PROG_ACC_OVR permits acceleration of all motions issued from a specific
program to be modified by the program. It is a program specific INTEGER with a
default value of 100%;
– $PROG_DEC_OVR permits deceleration of all motions issued from a specific
program to be modified by the program. It is a program specific INTEGER with a
default value of 100%;
– $ARM_ACC_OVR permits acceleration of a specific arm to be modified by a
program. It is an INTEGER field of the array, $ARM_DATA, with one field for each
arm. The default value is 100%;
– $ARM_DEC_OVR permits deceleration of a specific arm to be modified by a
program. It is an INTEGER field of the array, $ARM_DATA, with one field for each
arm. The default value is 100%.
The equations for total override for acceleration and deceleration are:
total acceleration override[arm] =
$GEN_OVR*$ARM_DATA[arm].ARM_OVR*$ARM_DATA[arm].ARM_ACC_OVR*
$PROG_ACC_OVR

total deceleration override[arm] =


$GEN_OVR*$ARM_DATA[arm].ARM_OVR*$ARM_DATA[arm].ARM_DEC_OVR*
$PROG_DEC_OVR
$PROG_ACC_OVR and $PROG_DEC_OVR are program specific INTEGER values
with default values of 100%. $ARM_ACC_OVR and $ARM_DEC_OVR are INTEGER
fields with one field per arm in multi-arm systems.
Changes in these four overrides take effect only on succeeding motions, not during any
current motion.
However, as with speed, changes in $GEN_OVR and $ARM_OVR take affect in the
current motion.
When HOLD, CANCEL, LOCK, or DEACTIVATE are used, maximum deceleration is
used regardless of the above override settings.

pr-0-0-gpr_04.fm
62 09/0313
Motion Control

In addition, a predefined variable, $HLD_DEC_PER, can be used to increase the


deceleration rate beyond normal maximum settings. At high speed, normal maximum
deceleration for some arms may require several hundred millimeters to stop. The range
of $HLD_DEC_PER is from 100 to 400 percent, permitting the normal maximum to be
multiplied by a factor up to 4. $HLD_DEC_PER is a read-only INTEGER array field of
the system-wide array of structures, $ARM_DATA[]. Thus, there is one element per axis
for each arm.

5.6.2 Joint Interpolation


After the governing joint is picked (based on speed), the speed of each of the remaining
joints is scaled by the ratio of original time for the joint to the time of motion of the
governing joint. Each joint must accelerate to its scaled speed, not to its requested
speed.
The acceleration time for each joint is evaluated to determine which joint will govern
acceleration. (This is not necessarily the same as the joint governing speed).
This time is a combination of $MTR_ACC_TIME[axis] and $JNT_OVR[axis]. A similar
combination, using $MTR_DEC_TIME and $JNT_OVR is used to find the governing
joint for deceleration.
After the limiting joints for acceleration and deceleration are determined (not necessarily
the same joint), all joints are scaled to accelerate and decelerate in the same amount of
time.
The previously described acceleration and deceleration overrides are also applied to
each joint.

5.6.3 Cartesian Interpolation


The same type of analysis done for joint acceleration and deceleration is done for
Cartesian acceleration and deceleration, except that instead of joints being compared,
translation and rotation are compared.
The acceleration and deceleration in the Cartesian motion (either linear or circular), with
any orientation evolution modality, is controlled by means of the following predefined
variables:
– $LIN_ACC_LIM specifies the maximum acceleration for linear translation. There is
a variable for each axis of each arm, whose values depend on the robot model and
cannot be modified by the User.
– $ROT_ACC_LIM specifies the maximum acceleration for rotation. There is a
variable for each axis of each arm, whose values depend on the robot model and
cannot be modified by the User.
– $LIN_DEC_LIM specifies the maximum deceleration for linear translation. There is
a variable for each axis of each arm, whose values depend on the robot model and
cannot be modified by the User.
– $ROT_DEC_LIM specifies the maximum deceleration for rotation. There is a
variable for each axis of each arm, whose values depend on the robot model and
cannot be modified by the User.
The predefined variables $LIN_ACC_LIM, $ROT_ACC_LIM, $LIN_DEC_LIM, and
$ROT_DEC_LIM are used to compute the component that takes the longest time.
These variables are REAL fields of the system-wide array, $ARM_DATA[ ], with one

pr-0-0-gpr_04.fm
09/0313 63
Motion Control

field per arm. The user is allowed to modify them by system level commands only.
The other components are scaled so that both rotations and translations use the same
time to accelerate and the same time to decelerate. The overrides are also applied.

5.6.4 Manual Motions


When programmed or immediate motions are issued in PROGR state, the described
above acceleration and deceleration overrides are used. However, when jog motions
are issued from the teach pendant, maximum deceleration is used to stop the arms.
An additional override, $MAN_SCALE, is used during manual motions to limit the
maximum speed to safe values. This manual override also affects acceleration and
deceleration to maintain trajectory shape for all motions issued in PROG state, except
for jog motions. For jog motions, $MAN_SCALE only affects speed. $MAN_SCALE is
set by the Builder and cannot be changed by the Customer.

5.7 Motion termination


It specifies the accuracy in robot positioning on the motion final destination, for a NON
FLY movement, before the next operation is performed.
For non-continuous motions, the predefined variable $TERM_TYPE is used to
determine when the motion will be terminated based on how close the arm must be to
its destination.
The predefined constants COARSE, FINE, JNT_COARSE, JNT_FINE, or
NOSETTLE can be assigned to $TERM_TYPE, with NOSETTLE being the default.

5.7.1 COARSE and FINE Termination


The COARSE and FINE values indicate two different thresholds that can be used to
define the motion stop (in-threshold). These thresholds, in the Cartesian frame, are the
radius of a sphere that has the target point as its centre. Furthermore:
– COARSE - must be used in Cartesian movements and indicates that the
movement is accomplished if the TCP stays inside the sphere which is centered in
the final destination, with a radius specified by $TOL_COARSE predefined
variable, for a time greater equal to $TOL_ABT (anti-bounce time).
– FINE - must be used in Cartesian movements and indicates that the movements is
accomplished if the TCP stays inside the sphere which is centered in the final
destination, with a radius specified by $TOL_FINE predefined variable, for a time
greater equal to $TOL_ABT (anti-bounce time).
The predefined variables $TOL_COARSE and $TOL_FINE indicate the tolerance
values. The default values for $TOL_COARSE and $TOL_FINE are arm dependent.
The predefined variable $TOL_ABT (anti-rebound time) indicates the time during which
the arm is to be within the specified tolerance before the motion is declared
completed/finished.
It has a range of 0 to 2000 milliseconds and a default value of 0 milliseconds. A value of
0 means the motion is terminated as soon as the arm is within the specified tolerance.
The predefined variable $TOL_TOUT (time out) determines the length of time the
system will continue checking to see if the arm is within the specified tolerance. It has a

pr-0-0-gpr_04.fm
64 09/0313
Motion Control

range of 0 to 20000 milliseconds and a default value depending on the kind of robot. The
value is rounded up to the nearest interpolator frequency ($IPERIOD) tick, so a value
less than this frequency is interpolated as one tick. If the arm does not come within the
specified tolerance within the specified timeout, an error with hold severity is issued.

5.7.2 JNT_COARSE and JNT_FINE Termination


The JNT_COARSE and JNT_FINE values specify the two different tolerances that can
be used to define the conclusion of the motion.
The predefined variables $TOL_JNT_COARSE and $TOL_JNT_FINE indicate the
COARSE and FINE tolerance values respectively, for each joint, measured in degrees.
They represent, for each joint, the acceptable tolerance range in degrees, to be able to
state that the motion has terminated on the final point. They are one dimension vectors.
Note that tolerance settings are joint settings, not tool centre point settings. To obtain
the correct tool centre tolerance values if the tool itself is large, it is necessary to use
lower tolerances than those used for smaller tools; in this case make reference to the
Cartesian frame thresholds (Fine, Coarse)

5.7.3 NOSETTLE Termination


The NOSETTLE value indicates that the motion is to be declared terminated as soon as
the deceleration profile has been completed. There is no settling time for the arm to
position itself precisely within a specified tolerance.
No controls are executed; NOSETTLE is the default setting.

5.8 Trajectory Recovery


If needed, motions can be stopped even before they are accomplished. For example, an
operator might press the HOLD key or the DRIVE OFF softkey. When HOLD button is
pressed, arms will smoothly decelerate and stop exactely on current trajectory. Pressing
START button will resume motion on current trajectory. No trajectory recovery is
needed. The same happens when the DRIVE OFF is requested but the power is also
cut out from the drives and the brakes are activated. The robot can be stopped by
opening the gates: in this case braking will take place with stop on the trajectory. The
robot can be stopped by pressing the safety mushroom-head button. In this case braking
will take place with stop on the trajectory, but with no in-threshold check.
With the status selector switch on T2, pressing the mushroom-head button causes a
stop WITHOUT control of the trajectory, with the power cut off and the brakes opened.

5.8.1 Recovery Strategy


Two forms of recovery are defined, short range and long range. Short range recovery
means recovery from a position that is very close to the original trajectory, as defined by
a predefined variable array of joint tolerances, $TOL_JNT[]. The short range reset takes
place by means of a move in joints interpolation that is entirely transparent to the user.
That is, when START button is pressed to resume a motion, a short range recovery
motion will be inserted immediately before the original motion is resumed. In many
cases, this reset move is not even perceived by the operator.

pr-0-0-gpr_04.fm
09/0313 65
Motion Control

If the distance between the current position and the nominal position is major to a certain
limit (short range) the resumption of motion takes place according to the modes defined
by the predefined variable $RCVR_TYPE value set. The possible values of this
predefined variable are shown in the following table:

0 Bring the arm to the interrupted trajectory position, by the joint interpolation.
1 Bring the arm to the movement start position that was interrupted by the joint interpolation.
2 Bring the arm to the interrupted movement destination position using the joint interpolation.
3 Do not reset, generate an error message.
4 If the interrupted movement was Cartesian, restore the interrupted trajectory by a straight-line
movement. Otherwise use joint interpolation .
5 If the interrupted movement was Cartesian, bring the arm back to the start position of the interrupted
movement by a straight-line interpolation. Otherwise use joint interpolation .
6 If the interrupted movement was Cartesian, bring the arm to the interrupted movement destination
position by a straight-line interpolation. Otherwise use joint interpolation .
7-8 reserved

Wherever it is possible to interrupt a program motion executed in Automatic mode, for


example setting it in HOLD state, then switch to Programming mode and jog the robot,
then go back to an Automatic mode. When START button is pressed, short or long
range recovery is determined and such a specified recovery strategy is performed.
When the system is in Programming state and a motion is interrupted by the DRIVE
OFF, recovery will be based upon conditions that exist when the drives are turned back
again and either START or BACK button is pressed. The recovery type will be
determined by whether or not there is a pending motion and from where the motion was
issued. The exact recovery type is determined as follows.

5.8.1.1 Pending Motion Status


If there are no pending motions either START or BACK button is pressed, then no motion
is performed. Recovery will only occur when there is a pending motion, and the recovery
type will be based on the recovery range.

5.8.1.2 Recovery Range


In Programming mode the same strategy is used as for the Automatic status. If the
distance between the stop position and the nominal position is limited, a joints
interpolation move is used to bring the arm to the point where the motion was interrupted
(short range); otherwise the $RCVR_TYPE variable is used (long range recovery) to
execute the recovery move.

5.8.1.3 Recovery procedure


If the System executes the recovery procedure, by issuing the corresponding messages
“Trajectory recovery in progress” and “Recovery position reached”, it is needed to
double press the START button.
On the contrary, if no messages are issued, just one pressure is required for the START
button.

pr-0-0-gpr_04.fm
66 09/0313
Motion Control

5.9 Process Resume


The process reset allows the robot to return back along the trajectory in progress before
returning to the programmed move. Hereafter this movement will be referred to as return
movement. The maximum distance requested must be defined in the system variable
$RCVR_DIST (in millimeters). If a zero value is attributed to $RCVR_DIST, such a
performance is disabled.
This performance is useful for applications in which the robot effects the process activity
during movement (typical examples are the welding arc and sealant application). If,
during some of these applications, movement is interrupted for any reason, part of the
trajectory that has already been covered should be retraced in order to avoid the risk of
skipping parts of the process.
The return movement is enabled after any stop: HOLD sent from the Teach Pendant,
HOLD due to error, LOCK, state selector switching, DRIVE OFF, emergency stop.
If the interruption is the result of an emergency or DRIVE OFF state, the trajectory will
probably be recovered before the return movement starts. In such cases the return
movement will start after trajectory restore has been performed. The user should
remember that the no return movement t is only allowed in the trajectory restore modes
at the point of interruption ($RCVR_TYPE=0 or 4); it is disabled if a return is performed
on either start or end point.
The return movement is interrupted in advance if it intersects a not in FLY position
(Fig. 5.7 - Return Movements - example D) or upon exhaustion of the movement
preceding the one in progress (Fig. 5.5 - Return Movements - example B and Fig. 5.6
- Return Movements - example C).

Fig. 5.4 - Return Movements - example A

Simplest situation.
1. Programmed Fly position, between two movements
2. First movement - fly termination
3. Second movement - fly beginning
4. Second movement - fly termination
5. Stop position
6. Motion direction
7. First movement – fly beginning

pr-0-0-gpr_04.fm
09/0313 67
Motion Control

Fig. 5.5 - Return Movements - example B

$RCVR_DIST programmed value is greater than the maximum recoverable one


1. Maximum recoverable distance
2. Stop position

Fig. 5.6 - Return Movements - example C

If a fly movement is interrupted, it is possible to go back twice


1. Stop position
2. Maximum recoverable distance

Fig. 5.7 - Return Movements - example D

The return movement is interrupted if a position is encountered


1. Maximum recoverable distance (because there is a non fly position)
2. Stop position

pr-0-0-gpr_04.fm
68 09/0313
Motion Control

Note that the return movement is possible during linear or circular type movements only.
The system reads the value of the distance to be recovered after each stop. Therefore,
if $RCVR_DIST is adjusted during the return movement, the value will only become
effective after the next stop.
If the return movement is interrupted, the $RCVR_DIST value is read again but the
distance to be recovered is always calculated starting from the point of the original
interruption (Fig. 5.8 - Example in case of $RCVR_DIST modification).

Fig. 5.8 - Example in case of $RCVR_DIST modification

1. Stop position of the return movement


2. First value of $RCVR_DIST=20 mm
3. Return movement interruption: $RCVR_DIST is read again
4. $RCVR_DIST=30 mm after the modification
5. Stop position

Any actual movement CONDITIONs are re-enabled at the next restart after the return
movement. However, if these have not been stated by means of the clause NODISABLE
they can only be released once.
If WHEN RESUME is enabled for an actual movement, this will be signalled at the end
of the return movement immediately before restarting the interrupted trajectory.
As for normal trajectory restore movements, automatic LOCK can be effected by means of
the variable $CRNT_DATA[num_arm].RCVR_LOCK. If the variable value is set to TRUE,
the system is automatically set to the LOCK state upon completion of the return movement.
There are four system events, one per arm, that signal entrance into the automatic LOCK
state (see “WHEN EVENT 130...133” in PDL2 Programming Language Manual). In
order to restart the movement a RESUME instruction must be effected by means of a
program PDL2 or the EXECUTE command on the Service page of the Teach Pendant
(in PROGR status).

5.9.1 Automatic Process Resume


It also exists a Process Resume mode working like trajectory recovery number 4
($RCVR_TYPE := 4); in such a modality the covered distance during the return
movement is $RCVR_DIST plus the covered distance, while decelerating, between the
stop command and the actual machine stop.
To enable such a modality, $RCVR_TYPE predefined variable is to be set to 9.

pr-0-0-gpr_04.fm
09/0313 69
Motion Control

1. motion direction
2. trajectory
3. calculated return movement
4. $RCVR_DIST
5. decelerate distance
6. motion stop command
7. actual motion stop position

5.10 Continuous Motion


The Continuous Motion allows the Program execution without stopping the Arm on the
taught positions.
To indicate a countinuous motion, the MOVEFLY statement is to be used, instead of the
MOVE statement. If one more movement follows the MOVEFLY, the Arm will not stop
on the first destination, moving instead from the starting position to the final position of
the second movement, without stopping on the common position of the two movements.

Fly movements between Joint trajectories an Cartesian trajectories are not allowed (NO
mixed fly).

See Fig. 5.9 - Example of continuous motion in case of linear movement. If another
motion follows the MOVEFLY, the arm will not stop at the first destination.

Fig. 5.9 - Example of continuous motion in case of linear movement

1. Movement start towards c


2. Movement end towards b

pr-0-0-gpr_04.fm
70 09/0313
Motion Control

5.10.1 Trajectory Shape During Continuous Motion


Fig. 5.9 - Example of continuous motion in case of linear movement shows a rounded
corner during the transition (fly) between the motion from A to B and the motion from B
to C. This rounding is a result of the deceleration of the first motion combined with the
acceleration of the second motion. The shape and amount of such rounding is a function
of the user settings ($FLY_PER, $FLY_DIST, $FLY_TRAJ), the speed of the two
motions, the values used for acceleration and deceleration, and the capability of the
servo system of the particular arm and payload.
When $GEN_OVR or $ARM_OVR are changed (or $JNT_OVR in the case of joint
interpolated motions), acceleration and deceleration are changed along with speed in order
to preserve the shape of the trajectory regardless of override. The shape will remain nearly
the same except for the effect of servo following error. The purpose of this feature is to permit
teaching at low override values with little or no touch-up required at production speeds.
Another effect of maintaining trajectory shape at low overrides is that the arm will
accelerate and decelerate more slowly. However, when HOLD, LOCK, CANCEL, or
DEACTIVATE are used, maximum deceleration is used to stop the arm.
When other speed overrides are changed, such as $PROG_SPD_OVR or
$ARM_SPD_OVR, acceleration and deceleration are not changed, and the shape will
change as a result. These overrides are used from within programs where it is desirable
to change only speed, and trajectory shape is unimportant during fly.

5.10.2 Continuous Motion Modes (FLY)


The predefined variable $FLY_TYPE determines which of several different algorithms
are used to control continuous motion. The algorithm used affects not only the speed
and shape of the trajectory during fly motions, but also the amount of stress placed on
the arm and on the component or tool connected to it.
The available $FLY_TYPE values are FLY_NORM and FLY_CART.

5.10.2.1 FLY_NORM
With $FLY_TYPE set to FLY_NORM, MOVEFLY causes the deceleration of the issued
motion to be overlapped with the acceleration of the next motion.
The predefined variable, $FLY_PER (the only one associated to FLY_NORM), can be
used to reduce the time in fly and to bring the trajectory closer to the intermediate taught
position. FLY_NORM is the default value.
Fly will begin at the start of normal deceleration for the motion plus a time equal to 100%
minus the percentage specified in $FLY_PER.
For example, if the value of $FLY_PER is 100%, the fly begins at the start of
deceleration of the fly motion. If $FLY_PER is 75%, then fly will begin after 25% of the
deceleration is finished (75% will be combined with the next motion).
The motion speed during fly is normally not constant. If two straight line segments are
joined by fly and are collinear then the TCP will move at constant speed through the
intermediate taught position as if there were one long segment. However, as the angle
between the two segments increases, the TCP will slow down near the intermediate
position, then speed up again as it moves into the next segment. The most extreme
example of course would be when the angle is 180 degrees (the TCP reverses
direction). In this case, the TCP will stop completely, but not at the intermediate taught
position.

pr-0-0-gpr_04.fm
09/0313 71
Motion Control

This type of continuous motion control generally causes the least stress on the arm and
part or tool during direction changes. Therefore, FLY_NORM is the default value for
$FLY_TYPE. If the angle between motion segments is very acute, then lower stress can
be achieved by using FLY_CART. (par. 5.10.2.2 FLY_CART (Controller Aided Resolved
Trajectory) on page 72).

5.10.2.2 FLY_CART (Controller Aided Resolved Trajectory)


Fly_CART is used for $FLY_TYPE when TCP constant speed is needed.
It also allows to control the shape of the trajectory during fly, or the stress on the arm, the
part, or the tool.
For FLY_CART to be effective, $SPD_OPT must be set to SPD_LIN and any movement
must be cartesian.
The default value for $SPD_OPT is SPD_CONST.
As long as various constraints (described below) are not exceeded, the TCP speed will
be maintained constant during fly between Cartesian (linear or circular) segments using
FLY_CART. FLY_CART may also be used during path motions between Cartesian
segments. FLY_CART has no effect when one or both of the motions is joint
interpolated.

5.10.2.2.1 Dynamic Machine Stress Control


The algorithm for FLY_CART control implements the idea of generalized stress, which
is made up three components of stress on the arm and tooling.
Large changes in orientation of the tool, high TCP speed, or large changes in direction
of the TCP all can cause large acceleration forces either on individual components of
the arm, on the part, or on the tooling. A generalized stress limit is defined, which is
proportional to programmed speed, the angle between adjoining trajectories, and the
required orientation change. This stress limit is user setable by the predefined variable
$STRESS_PER.
The default value of $STRESS_PER is 50%, and it must be in the range of 1% - 100%.
Higher values for $STRESS_PER indicate more stress, lower values less stress.
Higher values indicate to the system that higher values of acceleration and deceleration
may be used. It will therefore begin and end fly closer to the taught intermediate point.
A value of 100% will attempt to pass directly through the intermediate point, with little or
no fly.
With $STRESS_PER = 50% and two straight line segments at 90 degrees and little
orientation change, the fly trajectory will be nearly the same as if $FLY_TYPE were set
to FLY_NORM. However, unlike FLY_NORM, the TCP speed will remain constant. If the
angle between the straight line segments is increased (the segments are more towards
collinear), the distance covered by the fly, in FLY_CART mode, will be shorter and
therefore the trajectory will be nearer to the intermediate position taken in relation to
FLY_NORM. If the angle is sharper, the trajectory will be farther from the intermediate
point than with FLY_NORM, but lower stress will occur than with FLY_NORM.
See Fig. 5.10 - Comparison between FLY_CART and FLY_NORM
($STRESS_PER=50) for a graphical display of such situations.

pr-0-0-gpr_04.fm
72 09/0313
Motion Control

Fig. 5.10 - Comparison between FLY_CART and FLY_NORM


($STRESS_PER=50)

A similar control is placed on the generation of circular trajectories. The velocity of


circular motions will be reduced to keep the stress of the arm within the limits specified
by $STRESS_PER. This reduction of motion velocity is more likely to occur with circular
motions having a small radius. (Note that this reduction is for the entire circle, not just
the fly trajectory between the circle and the next motion).
Keep the following points in mind when determining a value for $STRESS_PER.
– The larger the value of $STRESS_PER, the larger the probability that the speed
will remain constant. Also, larger values of $STRESS_PER will bring the trajectory
nearer the taught intermediate position. In reality however, an increase in
$STRESS_PER can place greater demands on the controller, causing the quality
of the trajectory to be reduced.
– When $STRESS_PER is set to 100%, the planned trajectories become very sharp
since they pass through the programmed point without a reduction in speed. This
can cause very high stress on the robot, the part, and the tooling in some cases.
– Lower values of $STRESS_PER can be used to reduce the stress caused by large
wrist orientation changes. However, this “smoother” trajectory will pass farther from
the taught intermediate position.

5.10.2.2.2 Constant Speed Maintenance


As already described, FLY_CART allows the TCP speed to be maintained as a constant
during the fly motion as long as the limit set by $STRESS_PER is not exceeded. It is
strongly suggested that this feature be used to take advantage of the built-in
computations for fly motion. The following rules affect speed control in this mode:
– As for all fly motions, if the planned motion is too short the desired speed can not
be reached. In this situation the speed maintained during the fly motion is the
speed at the moment the fly started.
– When using high linear speeds, some motions will be too short and not allow time
for the necessary preliminary calculations. In this case the FLY_CART setting
behaves the same as all the other settings-i.e. the speed can not always be
maintained as a constant.
– The speed will not remain constant if the limit set in $STRESS_PER is exceeded
by the programmed trajectory.

5.10.2.2.3 Control of Trajectory During FLY


Quando la modalità fly viene impostata a FLY_CART, la traiettoria può essere

pr-0-0-gpr_04.fm
09/0313 73
Motion Control

controllata impostando:

When the fly motion type is set to FLY_CART, the trajectory can be controlled by setting:
– $FLY_DIST specifies a distance (in millimiters, default 5 mm) between the the
taught intermediate position and some point on the trajectory. The exact meaning
of the distance is determined by
– $FLY_TRAJ which can be set to
• FLY_AUTO it is the control which picks the closest trajectory to the
intermediate position that achieves the programmed speed without exceeding
the $STRESS_PER value.
Achieving and maintaining programmed speed has higher priority than
nearness to the intermediate position.

Be careful! $FLY_DIST is only used if $FLY_TRAJ is DIFFERENT from FLY_AUTO

• FLY_TOL guarantees the TCP to pass a distance less than $FLY_DIST from
the intermediate point of the trajectories.
If the generated trajectory falls within the distance $FLY_DIST, then the
trajectory will remain unchanged. However, if the trajectory is outside this
limit, then that distance limit will be respected and the speed will be reduced
to maintain the limits specified by $STRESS_PER and $FLY_DIST.
• FLY_PASS attempts to move the TCP at the exact distance from the medium
point.
If the planned distance, specified by $FLY_DIST, is too long with respect to
the length of the trajectories, then the fly trajectory is calculated to cross at the
maximum distance possible. If the distance specified is less than that which
would be produced by FLY_AUTO, the speed will be reduced to respect the
limit set by $STRESS_PER (the distance specified will still be maintained
exactly).
• FLY_FROM forces the fly motion to begin at the distance specified by
$FLY_DIST from the taught intermediate position.
Note that the dynamics of the machine could make it impossible for the programmed
distance to be maintained. This becomes more likely as the value of $STRESS_PER is
decreased.

Fig. 5.11 - FLY Movements

pr-0-0-gpr_04.fm
74 09/0313
Motion Control

The above picture (Fig. 5.11 - FLY Movements) shows an example of the use of these
system settings. With $FLY_DIST set equal to 20 mm, the following results will be seen.
When the value of $FLY_TRAJ is set to:
– FLY_TOL, then the distance A will be less than or equal to 20 mm;
– FLY_PASS, then the distance A will be 20 mm;
– FLY_FROM, then the distance B will be 20 mm.

5.10.2.2.4 Debug of Fly Motions


When debugging FLY_CART motions a field of $CRNT_DATA can be used to
determine the status of the last motion. The field name is $FLY_DBUG and will be zero
if the optimized trajectory was obtained or will contain a value to indicate the state of the
movement.
The FLY_DBUG field can be used in a NOHOLD program, from condition handlers, etc.
The programs can simply write the value to the display device for evaluation or
undertake some corrective actions. After the program has been properly configured
these debugging aids should be removed so they don’t slow the system down
unnecessarily. The following program demonstrates a simple example of the
FLY_DBUG used in a CONDITION.

PROGRAM mov_cart
CONST
arm_num = 1
cond_num = 1

ROUTINE print_debug
BEGIN
WRITE ($CRNT_DATA[arm_num].FLY_DBUG, NL)
END print_debug
BEGIN
$CRNT_DATA[arm_num].FLY_DBUG := 0
CONDITION[cond_num] NODISABLE :
WHEN AT END DO
print_debug
ENDCONDITION
-- initialisation
ENABLE CONDITION[cond_num]
-- move statements
END mov_cart

Tab. 5.2 - FLY_DBUG field codes for $CRNT_DATA variable

Code Description
0 Optimal situation indicating that the speed is maintained constant and the trajectory, planned
with $FLY_DIST, is guaranteed.
1 The fly lasts for less than 40ms. It is impossible to activate the constant speed algorithm. This
code is informational only; speed is maintained constant.
2 The angle between the trajectories is too small (less than 5 degrees) so it is impossible to
activate the constant speed algorithm.

pr-0-0-gpr_04.fm
09/0313 75
Motion Control

Tab. 5.2 - FLY_DBUG field codes for $CRNT_DATA variable (Continued)

Code Description
3 Acceleration reduction due to an extreme orientation evolution. This is caused by the
evolution of the tool orientation during fly. In this situation, the fly is smoothed and the speed
is maintained constant.
4 Replanning due to weaving causes a distance to be set, which is greater than the user
programmed one ($FLY_DIST). The speed is maintained constant.
5 Speed for passing the planned distance is reduced. In order to respect the restriction of the
passage ($FLY_DIST) and the restriction on the stress ($STRESS_PER), speed is
automatically reduced during fly. By default, $FLY_DIST is set to 5 and $FLY_TRAJ is set to
FLY_TOL. To overcome this speed reduction, increased the tolerance on the planned
trajectory (i.e. increase $FLY_DIST) or increase $STRESS_PER.
6 Speed reduction on a circular motion due to extreme stress. This code means that the
limitation on the maximum stress ($STRESS_PER) is imposing a speed reduction on the
whole circular trajectory. This can be overcome by increasing the radius of the circle,
increasing the value of $STRESS_PER, or reducing programmed speed.
7 Speed reduction due to an extreme orientation evolution. The orientation evolution required
during fly imposes speeds that are greater than the maximum allowed and the speed is
reduced during trajectory. To overcome, spread the orientation variation on the previous and
next motion or increase $STRESS_PER.
8 It is impossible to respect the passage at the planned distance and the resulting distance is in
effect reduced. This occurs only when $FLY_TRAJ is set to FLY_PASS or FLY_FROM. The
passage was programmed by the user to pass through a point that is too far away. It is
possible to obtain some advantages by decreasing the speed or by increasing the
$STRESS_PER value.
9 e 10 Current motion is too short to keep constant speed during fly. The planned speed is reached
during the movement. To change such a condition, increase (if possible) the distance
between the planned points and increase $STRESS_PER.
11 Motion too short to reach the planned speed because the acceleration phase cannot be
terminated. If possible, increase the distance between the two planned points. In some
cases, it could be useful to increase $STRESS_PER.
12 Extreme stress for a short motion. The resulting motion is too short for the execution of the fly
that guarantees the limitations on the maximum stress. The resulting stresses are greater
than the planned ones and the speed could change during fly. To change this condition,
increase (if possible) the distance between the planned points and increase $STRESS_PER.
13 Extreme stresses on the orientation evolution due to a short motion. The resulting motion is
too short for executing a fly that guarantees the limitations on the maximum stress in the
orientation evolution. The resulting stresses are greater than the planned ones and the speed
could change during fly.
14 e 15 Impossibility of fly re-planning due to lack of time. The movement does not last long enough
to allow the completion of the preliminary counts. The resulting stresses are greater than the
planned ones and the speed could change during fly. If possible, increase the distance
between the two planned points. In some cases, it could be useful to increase
$STRESS_PER.
16 Impossibility of fly re-planning with extreme stresses on the orientation evolution. The
resulting stresses are greater than the planned ones and the speed could change during fly. If
possible, increase the distance between the planned points and reduce the planned speed
($LIN_SPD). In some cases, it could be useful to increase $STRESS_PER.

5.10.2.2.5 Variables used with FLY Motion


If $FLY_TYPE is equal to FLY_CART, the following table summarizes the other values

pr-0-0-gpr_04.fm
76 09/0313
Motion Control

that must be defined.


– $STRESS_PER { value from 1% to 100% }
– $CRNT_DATA[arm].FLY_DBUG: usually used for read-only
– $FLY_TRAJ values: FLY_AUTO, FLY_TOL, FLY_PASS, FLY_FROM
– $FLY_DIST: values in millimeters. This is used when $FLY_TRAJ is different from
$FLY_AUTO.

5.11 Remote Tool System


Remote tool system is a particular configuration in which the robot is treated as a positioner
referred to a fixed tool. The robot carries the workpiece so that the TCP of the fixed tool
follows the right trajectory on the workpiece.
This is very common in applications where the tool either is much heavier than the part
or is immobile for some reason.
The remote tool system is enabled by setting the $TOOL_RMT system variable to
TRUE: it is a predefined variable belonging to $ARM_DATA group which is NOT reset
at Program deactivation; furthermore, its value is saved in the .C5G file by means of the
Config.Function (F1) - SETUP Page on the Teach Pendant.
Since this variable is a field of $ARM_DATA, it is not reset upon program deactivation
and, in addition, its current value is saved in file.C5G by ConfigureSave command.
Note that the workpiece frame is now defined with respect to the flange of the robot by
means of $UFRAME, while $TOOL represents the position of the remote TCP with
respect to the world frame (Fig. 5.12 - Remote Tool System).

Fig. 5.12 - Remote Tool System

1 - Flange Frame 2 - User Frame 3 - TCP Frame 4 - Fixed Tool 5 - Base Frame 6 - World Frame

pr-0-0-gpr_04.fm
09/0313 77
Motion Control

In cartesian movement ($BASE, $TOOL, $UFRAME), WITH ENABLED REMOTE


TOOL, while programming robot movement it is necessary to consider the remote tool
virtual motion, INSTEAD OF the actual robot motion.
Example: WITH ENABLED REMOTE TOOL, to be able to execute a Z+ motion in
$BASE Frame of reference (which means Z upward motion), robot must move along Z
downward, because, in such a way, it is a virtual upward movement of the remote tool
(which is actually fixed!): this means Z+ in $BASE as requested by the user.

5.12 Integrated Movement


When the base of a robot is mounted on another mechanism in order to extend the work
envelope, integrated management of the two mechanical systems is possible. Two
situations may arise according to whether the mechanism that transports the robot
consists of a single auxiliary axis (integrated axis) or of a second robot (integrated arms).

1. Slide Base Reference 2. Robot Base 3. User Reference 4. World Reference


5.. Side View 6. Top View 7. Column rotation 8. Rotating Column
9. Column Base Reference 9. Robot Base 10. User Reference 11. World reference
12. Rotating Column 13. Column rotation 14. Slide

pr-0-0-gpr_04.fm
78 09/0313
Motion Control

5.12.1 Integrated Axis


A robot can be mounted on an auxiliary axis in order to extend the work envelope. The
axis may be a slide (translating axis) or a Rotating Column.
In such a situation, it is possible to integrate the auxiliary axis in the movement of the
robot. This means that the cartesian position of the robot is calculated taking into
account the position of the auxiliary axis and therefore in relation to a reference integral
with the floor of the cell (WORLD reference), rather than with the base of the robot.
Practically speaking, it will be possible to move the TCP along a linear or circular path
while the slide/column is moving or to move the slide/column keeping the TCP still in
relation to the floor: in both cases, the robot axes will offset the movement of the auxiliary
axis.
The system sees the set of axes of the two mechanisms as a single manipulator. All the
types available, i.e. JOINTPOS, POSITION, XTNDPOS, can be used to assign the
destination positions of the movements. In the case of XTNDPOS, it is also possible to
specify the cartesian position of the TCP as well as the position of the auxiliary axis at
the same time.

For the configuration parameters, see the Chap. Use of Positioners managed by C5G.

5.12.1.1 Jogging
Moving the slide/integrated column manually (jog), the robot acts differently according
to the handing mode set: in joints mode, pressing the key corresponding to the
slide/column, the robot axes do not move; only the auxiliary axis moves. On the other
hand, in Cartesian mode of manual motion (BASE, TOOL, UFRAME) key 7 moves the
slide/column, keeping the TCP stationary, wherever the robot axes compensate the
movement of the auxiliary axis.

5.12.1.2 Reference Systems


With the slide/integrated column, the base reference of the system of axes (defined
using the $BASE variable) is located at the base of the slide/column. The other
reference systems remain unchanged as described in Frames of Reference section and
shown in following Fig. 5.13.

Fig. 5.13 - Base Reference System – integrated axes

1 - Rotating Arm Radius (R)

2 - Right-hand rotation of the Column

3 - Column Height (H)

4 - Left-hand rotation of the Column

pr-0-0-gpr_04.fm
09/0313 79
Motion Control

5.12.1.3 Restrictions
Integrated movement of the slide/column and robot is possible in the following
conditions:
– there are no limitations as regards the robot model; however this can be positioned
in relation to the flange of the slide/column in only eight positions, i.e.: the
Zbase_robot axis always parallel to Zbase_slide/column (in both directions) and the
Xbase_robot axis aligned with the Xbase_slide/column or Ybase_slide/column (four possible
directions);
– the axis corresponding to the slide/column must be the first available auxiliary axis;
– it is possible to integrate a single slide or column for each robot;
– it is not possible to enable or disable integration of the slide/column in real time (the
controller must be restarted).

5.13 Palletizing functionality (optional feature)

Palletizing Motion
The option code is CR17926214.

This optional feature allows using as a PALLETIZER, any anthropomorphic or


parallelogram robots, with 6 axes, spherical wrist.
The robot moves always keeping the flange parallel to the floor (with the TOOL z)
downward; axis 4 is NOT used.
Such a functionality allows to reduce the cycle time and to perform mixed trajectories
(both with and without FLY).
The wrist (W) configuration flags are NOT taken into consideration, making
programming easier.

Note that it is possible to use the robot either in standard functioning


(anthropomorfic/parallelogram with 6 degrees of freedom) or as a Palletizer (4 degrees
of freedom), just by modifying the machine configuration, with no needs of restarting it.

To use such a functionality, it is needed:


– purchasing the software option,
– spherical wrist SMART robot,
– moving the robot to have:
• axis 4 set to 0
• orientation set to <0, 180°, E3> (which results, depending on the robot,
adding joints 2, 3 and 5);
– no pending movements on the corresponding Arm,
– setting $JNT_MTURN flag (minimum path joint trajectory) to FALSE.
If one or more of the listed above conditions are not satisfied, an error occurs.
The following topics are now described:

pr-0-0-gpr_04.fm
80 09/0313
Motion Control

– Enabling
– Disabling
– Example of a Palletizing Program.

5.13.1 Enabling
a. Move the robot (the functionality must be disabled) to the required position to
enable it,

b. issue the enabling command in one of the following ways:


– from within a PDL2 Program - call ARM_PALLETIZING (ON, <arm_num>)
built-in routine to activate the functionality for Arm “arm_num”

For further information, please refer to PDL2 Programming Language manual -


BUILT-IN Routines List chapter.

– from Teach Pendant - select the required Arm, move the focus to the
Palletizer Status in the Motion Page - Status subpage (see Fig. 5.14 - yellow
highlighted field), so that Enable (F1) softkey is displayed in the Bottom Menu
(see Fig. 5.14 - red highlighted key). Press the key.

Fig. 5.14 - Palletizing Funtionality on the TP - enabling

c. Verify that in the sixth field of the TP status bar, Pallet is now specified (see
Fig. 5.15 - purple highlighted field).

NOTES
– Since the activation moment, it will NOT be possible to jog the robot axes
which are bind to keep the second Euler angle geometry to 180° (which
means to have the flange position parallel to the floor), and axis 4.
– In the trajectory generation, the system will automatically take care of
computing optimized trajectory for palletizing operations.
– It is possible to use the robot as a Palletizer, both in programming mode and
in automatic cycle.

pr-0-0-gpr_04.fm
09/0313 81
Motion Control

5.13.2 Disabling

First of all, it is needed that there are NO PENDING MOVEMENTS.

To disable the Palletizing Functionality and recover the usual robot functioning again, it
is needed to issue the disabling command in one of the following ways:
– from within a PDL2 Program - call ARM_PALLETIZING (OFF, <arm_num>)
built-in routine to deactivate the functionality for Arm “arm_num”

For further information, please refer to PDL2 Programming Language manual -


BUILT-IN Routines List chapter.

– from Teach Pendant - move the focus to the Palletizer Status in the Motion Page
- Status subpage (see Fig. 5.15 - yellow highlighted field), so that Disable (F2)
softkey is displayed in the Bottom Menu (see Fig. 5.15 - red highlighted key). Press
the key.

Fig. 5.15 - Palletizing Functionality on TP - disabling

5.13.3 Example of a Palletizing Program


PROGRAM test_arm_palletizing
VAR pnt0006P, pnt0007P : POSITION
pnt0001P, pnt0002P, pnt0003P, pnt0004P, pnt0005P : POSITION

BEGIN

$JNT_MTURN := FALSE

ARM_PALLETIZING(ON,1)
MOVE JOINT NEAR pnt0002P BY 300
MOVEFLY LINEAR TO pnt0002P ADVANCE
MOVEFLY LINEAR NEAR pnt0003P BY 20 ADVANCE
MOVE LINEAR TO pnt0003P

pr-0-0-gpr_04.fm
82 09/0313
Motion Control

MOVEFLY LINEAR AWAY 400 ADVANCE


MOVEFLY JOINT TO pnt0004P ADVANCE
MOVEFLY LINEAR TO pnt0005P ADVANCE
MOVEFLY LINEAR NEAR pnt0006P BY 300 ADVANCE
MOVEFLY LINEAR TO pnt0006P ADVANCE
MOVEFLY LINEAR NEAR pnt0007P BY 20 ADVANCE
MOVE LINEAR TO pnt0007P
MOVEFLY LINEAR AWAY 1000
ARM_PALLETIZING(OFF,1)
END test_arm_palletizing

pr-0-0-gpr_04.fm
09/0313 83
Synchronous Motion (optional feature)

6. SYNCHRONOUS MOTION (OPTIONAL


FEATURE)

Synchronized Arms
The option code is CR17926204.

This chapter describes the Synchronous Motion optional i.e., the synchronous motion
between a robot and other axes.
In particular, the following subjects are dealt with:
– Synchronization with Auxiliary Axes
– Synchronized Arms
– Motion limitation of the two Arms
– Jogging Synchronized Arms
– Teaching and Modifying Positions (REC/MOD) with Synchronized Arms
– Loss of Synchronization
– Run-time modifying the Linear Speed Override

6.1 Synchronization with Auxiliary Axes


If the axes belong to the same robot arm they are called auxiliary axes and they always
move in a synchronized way with the robot. This means that all the axes start and stop
at the same time.
The movement can be programmed with the JOINTPOS data type, which contains the
joint position of each axis, or by means of the XTNDPOS data type which is composed
of a Cartesian position for the robot and an ARRAY of joint values for the remaining
axes. The use of XTNDPOS data type is recommended.

6.2 Synchronized Arms


The motion of two arms is said to be time synchronized when they start and stop
together. To program synchronized motions of two arms the SYNCMOVE clause on the
MOVE statement has been implemented.
This feature is useful, for example, in a double P-MAST workcell with the two arms
carrying a single workpiece. In addition this feature is necessary for cooperative motion
(see par. 7.1 Cooperative Motion with Auxiliary Axes on page 90).
The Arms involved in synchronised motion are:
– MASTER Arm - it is always the arm that executes the MOVE;
– SERVER Arm - it is always the arm that executes the SYNCMOVE.
In the following synchronised MOVE:

pr-0-0-gpr_07.fm
84 08/1012
Synchronous Motion (optional feature)

MOVE ARM[1] LINEAR TO PNT0001P SYNCMOVE ARM[2] JOINT TO PNT001J

the MASTER Arm is ARM[1] and the SERVER Arm is ARM[2]; whereas in the next
synchronised MOVE :

MOVE ARM[2] LINEAR TO PNT0001J SYNCMOVE ARM[1] JOINT TO PNT001P

the MASTER Arm is ARM[2] and the SERVER Arm is ARM[1].


s

If a SYNCMOVE is executed with enabled cooperative movement between Arms (either


ARM_COOP or ARM_MCOOP), the Arms order is important and it is not equivalent: the
MASTER Arm must be the WORKER Arm, whereas the SERVER Arm must be the
POSITIONER Arm; note that the POSITIONER Arm is either the actual positioner Arm
(in case of ARM_COOP) or the owning Arm of the auxiliary axes which act as positioner
in case of ARM_MCOOP.
Please refer to par. 7.3 Multi-cooperative motion on page 92 for further details about
Arm Positioner and Arm Worker concepts.

All this, does not depend on the declared (or implied) Arm, PROG_ARM, at the head
of the program.
The system variable $SYNC_ARM specifies the default synchronized arm for the
SYNCMOVE clause, similar to $PROG_ARM that defines the default arm for the MOVE
statement. This variable is specific for the program and initialized by the user. For
example, in writing MOVE TO p1, since the arm has not been specified, the value of
$PROG_ARM is assumed. Similarly, in writing SYNCMOVE TO p2, since the arm for
the SYNCMOVE has not been specified, the value of $SYNC_ARM is assumed.
An example follows of a program that controls two Arms that move in synchronised
mode:

PROGRAM example
BEGIN
-- the main arm is arm 1, the synchronised arm
-- is arm 2
MOVE ARM[1] TO p1 SYNCMOVE ARM[2] TO p2
MOVE TO p1 SYNCMOVE ARM[2] to p2
-- $PROG_ARM moves on p1
MOVE ARM[1] TO p1 SYNCMOVE TO p2
-- ERROR: $SYNC_ARM is not initialised
$SYNC_ARM := 2 -- $SYNC_ARM is initialised
MOVE ARM[1] TO p1 SYNCMOVE TO p2
-- $SYNC_ARM (arm 2) moves on p2
MOVE TO p1 SYNCMOVE TO p2
-- $PROG_ARM and $SYNC_ARMEND are used, example
The ADVANCE clause is applied to the entire MOVE... SYNCMOVE. To perform a fly it
is necessary to specify the FLY clause on the main move and insert ADVANCE before
SYNCMOVE:

MOVEFLY TO p1 ADVANCE,
SYNCMOVEFLY ARM[2] TO p2,
ENDMOVE
If an ADVANCE is inserted after p2, the translator sees a warning message and
automatically corrects instruction.

pr-0-0-gpr_07.fm
08/1012 85
Synchronous Motion (optional feature)

6.3 Motion limitation of the two Arms


The combined motion of the two Arms imposes motion limitation. The following table
highlights the parameters that limit the motion in two frequent situations :

MASTER Arm trajectory $SPD_OPT value Limiting arm

Arm with more restrictive


joints or Cartesian SPD_JNT or SPD_CONST
parameters
different to SPD_JNT and to
Cartesian MASTER Arm
SPD_CONST

It will be the task of the user to specify a speed option that is compatible with the
combined motion, since for both Arms all the limitations are valid that are present on the
individual robot: for example a short translation of the MASTER Arm, with
$SPD_OPT:=SPD_LIN, combined with a wide variation of the SERVER Arm orientation,
imposes an over-speed on the SERVER Arm that cannot be controlled with the override
values only.
It can be seen that in the programming of a multi-arm system with two robots that both
move in Cartesian mode with
$SPD_OPT:=SPD_LIN and with
$LIN_SPD equal,
but on paths of different lengths, only the MASTER Arm will observe the speed
restriction, whereas the SERVER Arm will move faster if it has to cover a longer path,
more slowly if the path is shorter.

6.4 Jogging Synchronized Arms


In a double arm system the user may activate two arms (DRIVES ON) and then jog each
of them. Before switching to DRIVES ON it is required to select the main arm (stored in
$TP_SYNC_ARM[1]) and the synchronized arm (stored in $TP_SYNC_ARM[2]). This
has to be performed from the Motion page, Basic sub-page, on the Teach Pendant if
the SYNCARM option has been acquired. If $TP_SYNC_ARM[2] is set to zero, only one
arm will be used, i.e. $TP_SYNC_ARM[1].
The arm specified in the Teach Pendant status bar, can be moved with the manual keys.
To pass from one arm to the other, the required Arm has to be either specified in the
Arm field of the Motion page, Basic sub-page, or using the Arm key (if needed
SHIFT+Arm) available in the Right Menu of the Teach Pendant. For further information,
see the C5G Control Unit Use - par. Use of the Teach Pendant - Right menu.

6.5 Teaching and Modifying Positions (REC/MOD) with


Synchronized Arms
The enabling and disabling of the SYNCMOVE teaching are selected through either IDE
Page (‘Selection - REC Setup’ command), or Program Edit and Memory Debug
environments, under item DEBUG SETUP SYNC.
When disabled, by pressing the REC key, MOVE ARM[#] TO p1 is taught, where # is

pr-0-0-gpr_07.fm
86 08/1012
Synchronous Motion (optional feature)

the number of the selected arm. Enabling the teaching of SYNCMOVE, by pressing the
REC key the MOVE ARM[#] TO p1 SYNCMOVE ARM[&] TO p2 is taught, where # is
the number of the $TP_SYNC_ARM[1] value and & is the value of $TP_SYNC_ARM[2]
(regardless of the ARM currently selected). Tab. 6.1 - Teach examples (REC key)
illustrates some teach examples.

Tab. 6.1 - Teach examples (REC key)

Main Arm Action


1 teaches “MOVE ARM[1] TO p1"
2 teaches “MOVE ARM[2] TO p2"
1 teaches “MOVE ARM[1] TO p3 SYNCMOVE ARM[2] TO p4"
2 teaches “MOVE ARM[2] TO p4 SYNCMOVE ARM[1] TO p5"

For further information, please refer to C5G Control Unit Use manual, IDE Page
section.

6.6 Loss of Synchronization


The cases in which loss of synchronization between several arms occurs are described
below. The first case is that of the TIL clause that can be applied either to the main arm
or to the synchronized one; when the event associated with the TIL clause triggers, the
related movement is cancelled and the synchronization is lost. If, during a synchronized
motion, the CANCEL statement is executed, the main arm motion is cancelled, while the
synchronized one continues, hence synchronization is lost. If the user needs to cancel
both, he must cancel the move on both arms.
If the user locks (with LOCK statement) one arm during a synchronized move, the
synchronization is lost. To maintain the synchronization, he must lock both the arms,
with the statement:

LOCK ARM[1], ARM[2]


This is not equivalent to:

LOCK ARM[1]
LOCK ARM[2]
After having locked both arms at the same time, even if arm 1 is resumed with the
RESUME ARM[1] statement, the synchronized motion does not restart. Only if the other
arm is also resumed, the synchronized move restarts on both the arms (RESUME
ARM[2]).

6.7 Run-time modifying the Linear Speed Override


w

A functionality exists which allows, under some special conditions, to run-time modify
the Linear Speed Override. For further information see also par. 5.5.2.2 Run-Time
modifying the Linear Speed Override on page 59.

In single Arm systems, there is only one predefined variable to be used to Run-time

pr-0-0-gpr_07.fm
08/1012 87
Synchronous Motion (optional feature)

modifying the linear speed: $LIN_SPD_RT_OVR.


Viceversa, in multi-arm systems, there is a $LIN_SPD_RT_OVR for each Arm; in order
to Run-Time modify the linear speed, it is needed to identify which one is to be used
while executing a SYNCMOVE.
It is very important to exactely understand on which Arm such a functionality is currently
active. To do that, operate as follows:
Let’s have the following PDL2 statement

MOVE ARM[i] TO P1 SYNCMOVE ARM[j] TO P2


we have three possibilities:

a. BOTH the Arms AREN’T a Robot

b. ONE Arm ONLY IS a Robot

c. BOTH the Arms ARE Robots.

a. no Run-time modifications are allowed for linear speed


b. the Run-Time modification of the linear speed is allowed on
the Robot only (using the $LIN_SPD_RT_OVR predefined
variable which is associated to such an Arm)
c. the Run-time modification is allowed on the Arm which is
executing a cartesian motion. Anyway it is always needed
to use the $LIN_SPD_RT_OVR predefined variable which
is associated to the Arm on which the Run-time
modification functionality is active.

In order to understand if the Run-time modification of the linear speed does apply, and
which is the involved Arm, just check the second bit of the following field:

$CRNT_DATA[num_arm].C_ALONG_1D[50]
it is automatically set by the system software, for the Arm on which the Run-time
modification functionality is active. If such a bit is set to TRUE, it means that the
associated Arm acts as master, as regards the Run-time speed modification during the
SYNCMOVE execution, while the other Arm follows the modifications. In such a way,
the motion synchronization is always satisfied.

pr-0-0-gpr_07.fm
88 08/1012
Cooperative Motion (optional feature)

7. COOPERATIVE MOTION (OPTIONAL


FEATURE)

Cooperative Motion
The option code is CR17926200.

The cooperative motion feature simplifies the programming of applications where a


workcell is composed of a robot and one or more positioners (i.e. a rotating table). When
cooperative motion is enabled, the robot position is defined with respect to the positioner
so that Cartesian trajectory can be executed at constant speed while moving the
workpiece. This is mainly useful in welding complex shapes or large workpieces.
A general rule can be followed in the case of cooperative motion: the $UFRAME
transformation defines the position of the workpiece with respect to the flange frame of
the active positioner and not with respect to the world frame. This is shown in (Fig. 7.1
- System frames with auxiliary axes cooperative motion and Fig. 7.2 - User frame with
auxiliary axes cooperative motion). This is because the user frame is not fixed but is
linked with the positioner.
Cooperation can be enabled between a robot and its auxiliary axes or between two
different arms.
This chapter describes the following subjects :
– Cooperative Motion with Auxiliary Axes
– Cooperative Arms
– Multi-cooperative motion
– Jogging.

pr-0-0-gpr_08.fm
08/1012 89
Cooperative Motion (optional feature)

7.1 Cooperative Motion with Auxiliary Axes


If the robot and the positioner are organized in a single arm workcell, the positioner axes
are controlled by means of XTNDPOS data types as auxiliary axes. The cooperative
motion for this type of positioner can only be enabled after the positioner has been
correctly configured. The $AUX_BASE system variable is an array of POSITION used
to define the location of the bases of the positioners with respect to the world.

Fig. 7.1 - System frames with auxiliary axes cooperative motion

1 - Positioner Flange Frame 2 - Positioner 1 3 - Positioner 2

Fig. 7.2 - User frame with auxiliary axes cooperative motion

1 - User Frame 2 - Positioner Flange frame 3 - Positioner Base Frame

To enable and disable cooperative motion, the following built-in procedure is available:

AUX_COOP(flag, joint_aus <<, arm>>)


The data type for the flag is boolean. It can be set to ON or OFF for switching the
auxiliary cooperative motion on or off. Aux_joint field is the number of the last axis
composing a positioner.
The arm field is the arm on which the auxiliary cooperative motion should be executed,
if not explicitly defined, $PROG_ARM is used.
For example, in a system with a 5-axes robot, a first 2-axes positioner (axis 6, 7) and a

pr-0-0-gpr_08.fm
90 08/1012
Cooperative Motion (optional feature)

second 1-axis positioner (axes 8) the syntax could be the following:

AUX_COOP(ON, 7) -- enables the cooperative motion with the first


-- positioner
AUX_COOP(ON, 8) -- disables the previous cooperative motion end
-- enables the cooperative motion with the
-- second positioner
AUX_COOP(OFF) -- disables the cooperative motion

7.2 Cooperative Arms


The cooperative motion between two arms of the same work cell controlled by the C5G
can be enabled defining the first arm as the working arm and the second one as
positioner arm. The working arm trajectory will be computed with respect to the flange
of the positioner arm.
To enable and disable cooperative motion between two arms, the following built-in
procedure is available:

ARM_COOP(flag <<, positioner_arm <<, working_arm>>>>)


The data type of flag is boolean. It can be ON or OFF to enable and disable the
cooperation. The second parameter is optional and specifies the positioner arm. If the
positioner arm is not specified, the value of the $SYNC_ARM system variable is
assumed. The third parameter is optional and specifies the working arm. If the working
arm is not specified, the value of the $PROG_ARM system variable is assumed.
Cooperation can be performed independently from the synchronization of the arms by
simply enabling it and moving the positioner and the working arms. However from a
programming point of view, synchronization is preferred.

Fig. 7.3 - System frames with cooperative Arms

1. 1 - Working Arm 2 - Positioner Arm

pr-0-0-gpr_08.fm
08/1012 91
Cooperative Motion (optional feature)

Fig. 7.3 - System frames with cooperative Arms shows how the different frames of
reference for the two arms are defined. The positioner (arm 2) moves its TCP (defined
by $ARM_DATA[2].TOOL) with respect to its user frame ($ARM_DATA[2].UFRAME),
while the TCP of the working arm ($ARM_DATA[1].TOOL) moves the TCP with respect
to a frame of reference referred to by the TCP of the positioner (by means of
$ARM_DATA[1].UFRAME).

7.3 Multi-cooperative motion


The word Multi-Cooperative means the possibility, for 2 ARMs, to cooperate together
with the same group of auxiliary axes (e.g. a positioner) belonging to one of the two
Arms.
NO MORE than 2 Arms can be involved in the multi-cooperation.
To enable/disable multi-cooperative motion, the following built-in routine must be used:

ARM_MCOOP(flag<, aux_joint<, positioner_arm<, working_arm>>>)


where

flag is a boolean parameter which can be set to either ON or OFF, respectively to enable
or disable the multi-cooperative motion;
aux_joint is the number of the auxiliary axis. It can be omitted if flag is set to OFF; on the
contrary, when flag is ON, aux_joint is needed;
positioner_arm, if present, specifies the number of the positioner arm. If not present,
$SYNC_ARM is assumed;
working_arm, if present, represents the number of the working arm. If not specified,
$PROG_ARM is used.
For further information, please refer to PDL2 Programming Language manual,
chap.BUILT-IN Routines List.

Fig. 7.4 - System frames with multi-cooperative Arms

1. Working Arm
2. Positioner Arm

pr-0-0-gpr_08.fm
92 08/1012
Cooperative Motion (optional feature)

Very important requirement for using multi-cooperation, is the proper positioning, inside
the cell, of all the involved objects, which means to properly assign both $BASE and
$AUX_BASE (see Fig. 7.4).

This optional functionality needs the following software option: ‘Cooperative motion’ -
see chap. Appendix - Software Options in Use of the C5G Control Unit manual.

7.4 Jogging
Cooperative motion provides easy programming for while jogging the positioner arm, the
working one follows the positioner in order to keep constant the torch position (location
and orientation) with respect to the workpiece. This feature simplifies the programming
of complex trajectories, saving time and reducing the number of points that must be
taught.
The cooperation during jog must be enabled with the ARM_COOP (for cooperative
arms), AUX_COOP (for auxiliary axes cooperation) and ARM_COOP (for
multi-cooperation) built-in procedures. These can be executed inside the program by
means of the key or through the Execute command on the Service page (Execute
softkey) on the Teach Pendant.

pr-0-0-gpr_08.fm
08/1012 93
Sensor Tracking (optional feature)

8. SENSOR TRACKING (OPTIONAL FEATURE)

Sensor Tracking
The option code is CR17926205.

The Sensor Tracking environment allows real-time adjustments of the Cartesian


trajectory based on indications coming from various sensors. The main characteristics
are:
– possibility to interface with a wide range of sensors (integrated in C5G, analog I/Os,
serial ports);
– projection of corrections in all the main reference systems (tool, user, world,
weaving);
– translation corrections and geometry variations;
– relative and absolute corrections;
– control possibilities with and without programmed move;
– sensors dedicated to each arm in multi-arm applications;
– possibility to configure the robot dynamic response;
– compliance to safety restrictions;
– complete compatibility with other C5G services.
Detailed information follows regarding these subjects:
– Principle of operation
– Configuration on several arms
– Sensor interface
– Sensor reference system
– Type of information acquired by the sensor
– Correction actuation criteria
– Sensor tracking enable mode
– Sensor malfunctioning
– Accumulative overall deviations management
– Programming example

8.1 Principle of operation


During normal operation, the robot is controlled on a programmed position that is
periodically updated at each interpolation period ($IPERIOD predefined variable). The
sensor tracking environment allows the robot to progressively move away from this
position concordantly with the requests coming from a sensor. This is obtained keeping
a deviation vector (overall deviations) that is applied to the nominal programmed
position.

pr-0-0-gpr_10.fm
94 08/1012
Sensor Tracking (optional feature)

The vector is composed of 6 components; the first three are the deviations in X, Y and
Z directions and the other three the rotations around the same axes. To better
understand the effect of sensor tracking, let us consider an application where there is a
programmed trajectory and a sensor that can bring the TCP on an optimised trajectory
that is different to that programmed. Let us suppose that the program consists of a joints
move on a start position, followed by two linear moves linked in fly and a final joints move
to reach a position out of range.
The program could be the following:

PROGRAM sensor
VAR
p1, p2, p3, p4 : POSITION
BEGIN
$SPD_OPT:=LIN_SPD--To check the linear speed
$LIN_SPD:=0.1 --Linear speed in m/s
MOVE JOINT TO p1
MOVEFLY LINEAR TO p2 ADVANCE
MOVE LINEAR TO p3
MOVE JOINT TO p4
END sensor
If the sensor is enabled along the Cartesian path from p1 to p3, the effect could be as
shown in Fig. 8.1 - Programmed trajectory and sensors control where the dashed line is
the programmed trajectory and the continuous line is the trajectory actually travelled by
the TCP under the control of the sensor; the arrow between the two trajectories is the
deviations vector. It can be seen in the example that the tracking terminates when the
nominal position reaches point p3; on this point, the Control Unit re-acquires the actual
position and resets the deviations accumulated along the path, then the next joints move
will terminate exactly on the programmed point p4 as required. The following
paragraphs illustrate all the characteristics of the sensor tracking environment with
explanations on how to use the system and Built-In variables to program applications
that use sensors.

Fig. 8.1 - Programmed trajectory and sensors control

1. Starting point
2. Arrival point
3. Programmed trajectory
4. Trajectory controlled by sensor

pr-0-0-gpr_10.fm
08/1012 95
Sensor Tracking (optional feature)

8.2 Configuration on several arms


C5G can control several robots at the same time (multi-arm system); to do so, the
sensor tracking can be enabled separately on different arms by system variables that
are $ARM_DATA and Built-In fields that allow the arm referred to as an optional
parameter .All the variables are listed in Tab. 8.1 - System variables for Sensor
Tracking; ; it also indicates the limits, the default value and whether the WITH clause
can be used with the variables. Since all the variables are $ARM_DATA fields, they are
not reset when the program where they have been modified is deactivated.
Furthermore, by executing Config.Function (F1) - Save the configuration file,
SETUP Page on the TP, they are saved in 'file.C5G' with their current value Tab. 8.2
- Built-In for Sensor Tracking illustrates the built-ins for sensors management.

Tab. 8.1 - System variables for Sensor Tracking

Name Type Limits Default WITH


$SENSOR_ENBL BOOLEAN True-False False YES
$SENSOR_TYPE INTEGER [ 0, 30 ] 0 YES
$SENSOR_CNVRSN ARRAY [6] OF REAL [ -inf, +inf ] 0 NO
$SENSOR_GAIN ARRAY [6] OF INTEGER [ 0, 100 ] 00 NO
$SENSOR_TIME INTEGER [ 0, 10000 ] 0 ms YES
$SENSOR_OFST_LIM ARRAY [2] OF REAL [ 0, +inf ] [0,0] mm, degrees NO
$SFRAME POSITION null position YES

Tab. 8.2 - Built-In for Sensor Tracking


SENSOR_SET_DATA ( err_track <,arm> )
SENSOR_GET_DATA ( sens_read <,flag <,arm>> )
SENSOR_GET_OFST ( ofst_tot <,arm> )
SENSOR_TRK ( bool <,arm> )
Where:
– errp_track, sens_read, ofst_tot are ARRAY[6] OF
REAL
– flag is an INTEGER value in read
– arm is INTEGER type

8.3 Sensor interface


A sensor is suitable for sensor tracking applications if it is able to measure one or more
physical values and obtain from them geometrical information regarding the optimal
position, i.e. calculate the error between the actual TCP position and the optimal position
on the workpiece. A sensor may be integrated in the system at different levels; it is
therefore possible to distinguish between INTEGRATED sensors and EXTERNAL
sensors. The $SENSOR_TYPE system variable distinguishes between these two
possibilities.

pr-0-0-gpr_10.fm
96 08/1012
Sensor Tracking (optional feature)

8.3.1 Integrated Sensors


Some sensors are pre-set for integration into the control system hardware. These
devices are integrated sensors if the communication between sensor and control
system is managed by system software and not only by PDL2 programs. The
intgegrated handling allows real-time correction of the robot trajectory exploiting the
reading of the arc current/voltage during high frequency weaving (Cartesian or joints
weaving). In this configuration the torch is kept on the being welded joint by subsequent
corrections in two directions: crosswise and vertical to the trajectory.
The $SENSOR_TYPE values for this type of sensor are between 1 and 4. Values 1 and
2 are reserved to the first board and values 3 and 4 to the second one (see Tab. 8.3).
In the case of integrated sensors, the communication of the sensor information takes
place at software level and therefore the values are not known directly at PDL2 level. To
read them there is the following Built-In SENSOR_GET_DATA:

$SENSOR_GET_DATA ( sens_read <, flag <, arm>> )


This copies the six components of the vector coming from the sensor into the sens_read
parameter: the first three elements correspond to the translations in X, Y and Z
directions and the others are the rotation around axes X, Y and Z.
If the sensor is only able to control some of the six components, the others will remain
at a value zero. The optional flag parameter is set to value 1 if the data is new i.e. it has
never been read by a previous SENSOR_GET_DATA instruction. Otherwise it is set at
0. The optional arm parameter selects the data relating to an arm that is not the default
one.

8.3.2 External sensors


External sensors are those which are not integrated in the Control System Hardware.
Examples of this type of sensors are:
– Simple limit switches or binary proximity sensors that give a single digital datum
(they change the signal when the distance measured exceeds a certain threshold);
– Capacitive or inductive proximity sensors that communicate by an analog input or
by coded information on several digital inputs;
– Sensors connected to the control system by a communication line managed by a
PDL2 program. The two-three dimension cameras may belong to this category
since they usually have a dedicated controller, that makes the necessary
calculations to interpret the image, and a communication line to receive the
commands and transmit the information.
These types of sensors have the characteristic that the reading of the information is
performed by a PDL2 program (usually NOHOLD), created specifically for the sensor.
The $SENSOR_TYPE values reserved for this type of sensor are included between 5
and 12 (see Tab. 8.3 - Correction_Speed = Factor*Reference_Speed). To send the
correction request to the movement environment the following Built-In has been
introduced :

SENSOR_SET_DATA ( err_track <, arm> )


The err_track parameter is the vector of the corrections required, the first three elements
correspond to the translations in X, Y and Z directions, whereas the others are the

pr-0-0-gpr_10.fm
08/1012 97
Sensor Tracking (optional feature)

rotations around the same axes.


The unused err_track components have to be initialised in any case to value zero. With
the optional "arm" parameter corrections can be sent to an arm that is not the default
one. The Built-In SENSOR_GET_DATA, described in the previous paragraph can also
be used with this type of sensors. In this case the sens_read variable will contain the
same data as sent with SENSOR_SET_DATA.

8.4 Sensor reference system


The sensors measure the deviations in relation to a reference system that depends on
the characteristics of the actual sensor, that is to say, according to its position and the
type of physical value measured. To cover all the possibilities, the following cases can
be determined: TOOL, USER, WORLD and WEAVE reference. To select these
different cases the $SENSOR_TYPE system variable is used .

8.4.1 Sensor integral with the tool (TOOL)


This type of reference is used when the sensor is mounted on the tool itself.
– This is the case of a proximity sensor mounted on the tip of the tool or a laser
camera on the welding torch. The most frequent case is the arc parameters sensor
in the arc height control mode or with joint type weaving; in the latter case the
TOOL reference has to be used because if the weaving is joints type, a weaving
reference system is not defined (therefore it would not make sense to use the mode
in WEAVE reference).
The $SENSOR_TYPE values reserved for this reference are: 1 for seam-tracking (not
available in 1.0 sw version), 5 and 9 for external sensors (Tab. 8.3 - Correction_Speed
= Factor*Reference_Speed).
In these tracking modes (TOOL reference) the reference system that describes the TCP
position ($TOOL variable) can be distinguished from the reference in which the sensor
makes the measurements.
To do this there is the $SFRAME system variable. This is a conversion of co-ordinates
referred to the TCP reference system, since it follows $TOOL in the kinematic chain (see
Fig. 8.2 - Tool frame conversion).

Fig. 8.2 - Tool frame conversion

1. Flange
2. Tool
3. Sensor
4. Sensor frame
5. TCP frame

pr-0-0-gpr_10.fm
98 08/1012
Sensor Tracking (optional feature)

8.4.2 Sensor integral with the user reference system (USER)


With this possibility the corrections can be projected in relation to the user reference
system defined by the $UFRAME system variable.
– This case also includes sensors that are mounted in a fixed position as to the work
station or that are handled by kinematics that permit the measures executed to be
brought back to the USER reference system .
$SENSOR_TYPE can enable this modality only for external sensors with codes 6 and
10 (see Tab. 8.3 - Correction_Speed = Factor*Reference_Speed).
Also in this case it may be necessary to assign a specific reference system to the
sensor, calculated according to the USER system. This can be obtained with the same
$SFRAME variable that, in these modes, represents a conversion in relation to the
USER reference (it follows $UFRAME in the kinematic chain, see Fig. 8.3 - User frame
conversion).

Fig. 8.3 - User frame conversion

1. World frame

$SFRAME also serves to select the centre of rotation for the tool geometry corrections.
If $SFRAME is not zero, the centre of rotation is defined by the $SFRAME itself,
whereas if all the components are null, the centre of rotation coincides with the TCP.

8.4.3 Sensor integral with the world reference system (WORLD)


This is an extension of the USER case. This mode permits the projection of the
corrections in relation to the world reference system - the system to which $BASE and
$UFRAME refer. The values of $SENSOR_TYPE for this mode, for external sensors
only , are 7 and 11 (Tab. 8.3 - Correction_Speed = Factor*Reference_Speed).

8.4.4 Sensor integral with the weaving reference system


(WEAVE)
This is exclusively for arc parameter sensors with Cartesian type weaving. In this case
the sensor makes the measurement through the torch; it is independent in its orientation
but depends on the direction of the weaving. The corrections calculated have to be

pr-0-0-gpr_10.fm
08/1012 99
Sensor Tracking (optional feature)

projected, not in the torch reference system (TOOL) but with regard to the weaving
(WEAVE).
The $SENSOR_TYPE values for this type of reference are 2 for seam-tracking (not
available in 1.0 sw version), 8 and 12 for external sensors (see Tab. 8.3
- Correction_Speed = Factor*Reference_Speed).

8.5 Type of information acquired by the sensor


The most sophisticated sensors give Cartesian corrections directly in millimetres,
whereas others just give the measurement of the physical value that, in the most
frequent cases, is directly proportional to the distance measured. In such cases the C5G
automatically converts the data read by the sensor (for example ampere, Newton, etc.)
to corrections in millimetres through the $SENSOR_CNVRSN system variable. This is
a vector of 6 REAL type elements that contain the conversion factors. Each sensor data
component is multiplied by a corresponding conversion factor before being applied to
the trajectory.
– for example a proximity sensor supplies a current or a voltage that can be
converted in millimetres by multiplying by a specific mm/A or mm/V factor ;
– the force sensors are a separate category, since they do not measure a position or
a physical value directly connected to them, but give an indication that there is the
"need to correct the trajectory" in a certain direction. For these sensors the factor
by which the signal is multiplied assumes the significance of a gain since with an
equal signal a correction is calculated in millimetres without being able to know the
exact size of the correction required.
If it is wished to exclude the effect of this conversion, it is sufficient to set the
$SENSOR_CNVRSN components to value 1 (default value). $SENSOR_CNVRSN can
also disable the application of one or more components of the correction: this is obtained
by setting the corresponding element of the vector to zero ($SENSOR_CNVRSN[n]:=0).

8.6 Correction actuation criteria


There are three elements that regard the actuation of the corrections: the first is to
distinguish between relative and absolute deviations; the second is for the mode in
which a correction is actuated in time; the third is to check the overall deviations between
the programmed position and the position reached under the control of the sensor.
The following subjects are described:
– Relative and absolute deviations
– Actuation of deviation in time
– Overall deviations control

8.6.1 Relative and absolute deviations


The deviations are considered ABSOLUTE if the correction is requested regarding the
nominal trajectory of the robot, i.e. that which is programmed (Fig. 8.4 - Absolute
deviations). The term RELATIVE deviations means a correction that is made with
reference to the current robot position, i.e. without taking into consideration the error

pr-0-0-gpr_10.fm
100 08/1012
Sensor Tracking (optional feature)

already accumulated during previous sensor readings (Fig. 8.5 - Relative deviation).

Fig. 8.4 - Absolute deviations

1. Programmed trajectory 2. Trajectory controlled by sensor


3. Correction required = +3 mm 4. Required = +1 mm
5. Required = -2 mm 6. Final deviation = 0 mm
7. Required = 0 mm

Fig. 8.5 - Relative deviation

1. Programmed trajectory 2. Trajectory controlled by sensor


3. Correction required = +3 mm 4. Required = +1 mm
5. Required = -2 mm 6. Final deviation = 0 mm
7. Required = 0 mm

For integrated sensors the choice between the two modes (absolute or relative)
depends on the type of sensor, and it is managed by system software. For external
sensors there is a possibility to choose by means of the $SENSOR_TYPE system
variable: the values from 5 to 9 enable the relative mode functioning, whereas from 9 to
12 enable absolute mode (Tab. 8.3 - Correction_Speed = Factor*Reference_Speed).
– in most industrial applications the sensors measure the RELATIVE deviations
since they are able to determine the optimal trajectory position in relation to their
own position. Also in the case of force sensors the most frequent use is to consider
the data measured in relative mode. This means that until the sensor output differs
from zero the trajectory is continually modified adding new deviations to the old
ones, whereas when the output is null, the accumulated corrections are kept and
the robot trajectory remains parallel to the nominal one (Fig. 8.4 - Absolute
deviations);
– the correction in ABSOLUTE mode is useful to obtain a yielding effect on the TCP
by means of force sensors. In practice a deviation is applied to the robot trajectory

pr-0-0-gpr_10.fm
08/1012 101
Sensor Tracking (optional feature)

that is proportional to the force sensor output. This causes the entire robot to
behave like a spring in all directions since as the measured force intensity
increases, the robot deviation from the programmed trajectory increases, when
there is no stress the robot returns to follow the programmed path (Fig. 8.5
- Relative deviation).

8.6.2 Actuation of deviation in time


Corrections measured by the sensor may also be several millimetres, especially if the
frequency at which the information is read is low. Therefore, in some cases it is not
possible to apply the entire deviation in one interpolation operation. There are two
possible rules for the distribution of the deviation during the move execution:
– define the speed (SPEED) at which the correction will be performed;
– define a time period (TIME PERIOD) during which the entire deviation will be
assimilated.
The first criterion guarantees the execution of the correction in the least time possible
and is useful in all cases where the time that lapses between two sensor readings is very
short (high frequency) or is not known.
However, in some applications this method determines a correction in "spurts" since ,
for small deviations the corrections are applied with a fast, brief movement of the robot.
In these cases the second criterion is more effective because it makes it possible to
distribute the entire deviation over a pre-set time.
To choose between these two modes the $SENSOR_TIME variable is used. If
$SENSOR_TIME is zero, the speed criterion is used. A value that is not zero selects the
second mode and indicates the time (in milliseconds) during which the correction is to
be applied.
For external sensors the new data will be read by the sensor only after this time has
expired, starting from the last corrections. Fig. 8.6 - Effects of $SENSOR_TIME (with
relative corrections) illustrates the effect of the two different criteria.

Fig. 8.6 - Effects of $SENSOR_TIME (with relative corrections)

1. Programmed trajectory 2. Trajectory controlled by sensor

pr-0-0-gpr_10.fm
102 08/1012
Sensor Tracking (optional feature)

In both the correction distribution modes, the speed can be assigned through the
$SENSOR_GAIN system variable. It is a vector with 6 INTEGER elements that have a
percentage significance (variability from 0 to 100 with default 50). It allows the program
to ratio the correction speed with the programmed movement execution speed.
The first three elements regard the translations in the X, Y and Z directions and in the
case of $SPD_OPT=SPD_LIN, they represent a measurement of the angle between
the programmed trajectory and that which results from the correction. The value 50%
corresponds to the slope of 45 degrees (correction speed equal to the advance speed,
$LIN_SPD), whereas the values 0% and 100% represent the extreme cases of no
correction (0%) and immediate assimilation of the correction (100%).
If $SPD_OPT is set for one of the rotation control modes (SPD_ROT, SPD_SPN,
SPD_AZI, SPD_ELV, SPD_ROLL, SPD_FIRST, SPD_SECOND, SPD_THIRD) the
reference speed for the first three components of $SENSOR_GAIN is one fourth of the
maximum linear speed for that arm ($LIN_SPD_LIM/4).
The last three elements of $SENSOR_GAIN serve to control the speed of rotation
around the X, Y and Z axes. If it is $SPD_OPT=SPD_LIN, the reference speed is a
quarter of the maximum rotational speed ($ROT_SPD_LIM/4) thus the value of 50%
corresponds to a speed equal to $ROT_SPD_LIM/4 whereas the values 0% and 10%
represent the extreme cases of no correction (0%) and immediate assimilation of the
geometry variation (100%). If $SPD_OPT is set to one of the rotation control modes
(SPD_ROT, SPD_SPN, etc.) the reference speed for this component is $ROT_SPD.
Tab. 8.3 - Correction_Speed = Factor*Reference_Speed contains the multiplication
factors that, applied to the reference speed, make it possible to obtain the actual
programmed speed. These values are given as an explanation only, since in practice,
the value of $SENSOR_GAIN will be determined by experimentation .

Tab. 8.3 - Correction_Speed = Factor*Reference_Speed

$SENSOR_GAIN[ i ] Factor
0 0.0
10 0.11
20 0.25
30 0.43
40 0.67
50 1.0
60 1.5
70 2.3
80 4.0
90 9.0
100 infinite

The $SENSOR_GAIN variable is also taken into consideration when the criterion for the
distribution of the deviations is time ($SENSOR_TIME is not zero). In this case the
$SENSOR_GAIN components will be used to define the maximum correction speed
(Fig. 8.7 - Effects of $SENSOR_GAIN). To avoid all types of limitation the
corresponding $SENSOR_GAIN value can be set at 100%.

pr-0-0-gpr_10.fm
08/1012 103
Sensor Tracking (optional feature)

Fig. 8.7 - Effects of $SENSOR_GAIN

1. Programmed trajectory 2. Trajectory controlled by sensor


3. Maximum speed 4. Time increase

The use of this variable will depend on the measuring accuracy of the sensor used, and
the frequency with which these measures are supplied. If the sensor gives a precise
indication of the deviation that is to be assimilated (in millimetres) but with a low
frequency, the value of $SENSOR_GAIN is directly linked to the correction speed. If
instead the sensor is able to give only a generic indication on the direction in which the
correction is required, the $SENSOR_GAIN variable can be used as a gain, i.e. as a
parameter to be set-up on the basis of the fluctuations that are observed during the
application.

8.6.3 Overall deviations control


The overall deviation has already been defined as a vector with 6 elements that
represent the actual position of the robot in relation to its programmed position. This
vector can be read through the following Built-In:

SENSOR_GET_OFST ( ofst_tot <, arm> )


The first three components of ofst_tot are the deviations in X, Y and Z directions, and
the other three components are the rotations around the same axes. The optional arm
parameter can be used to read the data of an arm that is not the default one.
This deviation vector will always refer to the USER reference system (the system
defined by $UFRAME by which all POSITIONs are defined) regardless of the
$SENSOR_TYPE value.

8.7 Sensor tracking enable mode


The sensor tracking can be activated on Cartesian trajectories only (LINEAR or
CIRCULAR) or, in certain situations, when there is no programmed move. The sensor
tracking is enabled by the $SENSOR_ENBL system variable. This can be assigned a
BOOLEAN type value (TRUE to enable and FALSE to disable). The variable can be
used alone in a single program line ( $SENSOR_ENBL:=TRUE/FALSE) or together with
a MOVE instruction with the WITH (MOVE LINEAR TO p1 WITH
$SENSOR_ENBL=TRUE/FALSE). The enabling and disabling of the tracking is closely
linked to the holding or the resetting of the overall deviations (see par. 8.9 Accumulative
overall deviations management on page 108”).
The standard enable mode of sensor tracking permits the application of corrections read

pr-0-0-gpr_10.fm
104 08/1012
Sensor Tracking (optional feature)

by the sensor only during the execution of a programmed move and therefore the sensor
is ignored when the robot is stationary (even if in DRIVES ON). This is the mode most
frequently used in practical applications.
However, there are certain applications where it is necessary that the robot position is
enslaved to the sensor even without a programmed move.
– a typical example is when the robot has to be latched to a moving object, or it
interacts with the workpiece without movement of any controlled axes, but closing
grippers or moving additional axes;
– there are also sensors that can move the robot autonomously without the need of
a programmed move.
C5G is preset for this type of application, offering the possibility to enable the arm in a
certain state in which it is completely enslaved to the sensor although still having the
possibility to resume the programmed move at any time.
When introducing this service complete consistency of behaviour has been maintained
with that already possible in C5G in compliance with safety requirements. In particular
the following points are highlighted:

a. robot enslaving to a sensor without a programmed move can only be enabled by a


HOLDABLE program with the Control Unit in AUTO;

b. the start of the enslaving always depends on the pressing of the START key, until
that moment the user is certain that the machine cannot move;

c. movement under the control of the sensor can be stopped by pressing the HOLD
key and can only start again when the START key is pressed;

d. the enslaving terminates when the program that started it is deactivated.


These services have been obtained by introducing a special type of Built-In that can only
be executed by HOLDABLE. programs. The syntax is:

SENSOR_TRKSENSOR_TRK ( boolean <, arm> )


The execution of the SENSOR_TRK(TRUE) instruction selects a certain option so that,
enabling the sensor tracking with the $SENSOR_ENBL variable, the arm is in an
extended mode that permits enslaving even without a programmed move.
The optional arm parameter can enable the service on an arm that is not the default one.
There are the following limitations (they refer to the Built-In executed always on the
same arm):

a. the actual enabling of the enslaving without a programmed move is subordinated


to the value of $SENSOR_ENBL (however, it is not necessary to re-run
SENSOR_TRK(TRUE) after bringing $SENSOR_ENBL to FALSE and then to
TRUE);

b. since the SENSOR_TRK can only be run within HOLDABLE programs, it cannot
be run neither using the Execute (F1) command - Service Page (Exec softkey) on
the TP, nor by the SYS_CALL of the EXECUTE command;

c. the service disabling through SENSOR_TRK(FALSE) can be executed only from


the same program that enabled it;

d. SENSOR_TRK cannot be executed if it is already enabled by a second


HOLDABLE program that is active at the same time;

pr-0-0-gpr_10.fm
08/1012 105
Sensor Tracking (optional feature)

e. the SENSOR_TRK mode is automatically disabled when the program that enabled
it is deactivated.
The enabling and disabling of the tracking in this mode has certain effects on the holding
or resetting of overall deviations (see par. 8.9 Accumulative overall deviations
management on page 108).

8.8 Sensor malfunctioning


There are two characteristics of the sensor tracking environment that help to minimise
the negative consequences of a sensor malfunctioning: the first makes it possible to stop
the robot, the second to redefine the correct deviations before resuming the interrupted
program.
Description of the following subjects:
– Robot stop in the case of sensor malfunctioning
– Redefinition of overall deviations

8.8.1 Robot stop in the case of sensor malfunctioning


In cases where the sensor is not reliable or is subject to disturbances, it could happen
that the robot moves too far from the programmed position with the risk of damaging the
fixture. For this situation the $SENSOR_OFST_LIM system variable has been provided.
It consists of 2 REAL type elements that indicate the maximum deviation allowed
between the programmed trajectory and the robot guided by the sensor. The first
element is for the translations (along X, Y and Z axes) and is in millimetres; the second
is for the rotations and is in degrees. When the limit of any of these components is
passed, an error message is sent and the robot is stopped in HOLD condition.

8.8.2 Redefinition of overall deviations


When examining error situations caused by malfunctioning of sensors, cases have been
noted where it is necessary to reassign the value of the accumulated deviations. In
particular this is indispensable when, because of a sensor error, the robot is taken away
from the optimal trajectory until it stops because it has exceeded the maximum
thresholds ($SENSOR_OFST_LIM). In these conditions the robot can be brought back
to the correct position and resume the running of the program by using two special
modes to restore the trajectory ($RCVR_TYPE).
By setting $RCVR_TYPE=7 the correct position can be redefined, bring the robot back
to the trajectory with the Teach Pendant and starting again: the interrupted movement
will be picked up again exactly from that position with no recovery. The deviations will
be automatically redefined with a new value. Fig. 8.8 - Effect of $RCVR_TYPE = 7
shows the procedure.

pr-0-0-gpr_10.fm
106 08/1012
Sensor Tracking (optional feature)

Fig. 8.8 - Effect of $RCVR_TYPE = 7

1. Programmed trajectory 2. Trajectory controlled by sensor


3. Trajectory after a sensor failure 4. Optimal trajectory
5. HOLD caused by an error message

Not only the translation deviations (first three components) are redefined, but also those
of geometry variations, therefore, if it is wished to resume the move with the same
geometry as when the stoppage took place, this must not be changed during the jog
session.
The $RCVR_TYPE=8 mode is useful in such cases and permits the move to be
resumed returning exactly on the programmed trajectory resetting the deviations
accumulated by the sensor; in this mode the C5G plans a trajectory that recovers the
current position to correspond to the programmed trajectory and resume the interrupted
move.
After recovery, the deviations will be reset. Fig. 8.9 - Effect of $RCVR_TYPE = 8 shows
how this mode functions.
The functioning of $RCVR modes from 0 6 are not submitted to variations in the case of
enabled sensor tracking. Therefore modes 0 and 4 bring the TCP exactly on the
interrupted position keeping the deviations accumulated up to that moment, whereas
modes 1, 2, 5 and 6 bring the robot on the programmed initial and final positions,
resetting the deviations.

Fig. 8.9 - Effect of $RCVR_TYPE = 8

1. Programmed trajectory 2. Trajectory controlled by sensor


3. Recovery trajectory 4. HOLD caused by an error message

pr-0-0-gpr_10.fm
08/1012 107
Sensor Tracking (optional feature)

8.9 Accumulative overall deviations management


In the par. 8.1 Principle of operation on page 94 a brief description has been given of
the procedure in which the robot position is modified according to the indications of a
sensor. Below it is explained how the enabling and disabling of tracking can interact with
the holding or resetting of overall deviations. To do so, it is necessary to introduce the
following concepts: interrupted sensor tracking session (INTERRUPTED), suspended
session (SUSPENDED) and the spread resetting of the deviations (RESETTING
SPREAD) .
The following subjects are described below:
– Interrupted sensor tracking session
– Suspended sensor tracking session
– Resetting in spread condition
– Limitations in parameter changes

8.9.1 Interrupted sensor tracking session


A sensor tracking session is considered interrupted when, during
SENSOR_TRK(FALSE), the robot stops on a position without the move that took it to
that position being in ADVANCE and where the FLY clauses have not been defined.
The interruption of the tracking is important because with this event an acquisition is
made of the TCP actual position, with the consequent resetting of the deviations.
To understand the effect of an interruption, compare Fig. 8.10 - Interrupted sensor
tracking session with Fig. 8.1 - Programmed trajectory and sensors control; the
difference between the two programs consists in the fact that the fly has been removed
(and also the ADVANCE) on the intermediate p2.
The result in practice is that the linear move to p3 will be executed no longer starting
from the programmed point p2 but from point p2'; in p2 the deviations are reset.

Fig. 8.10 - Interrupted sensor tracking session

1. Programmed trajectory 2. Trajectory controlled by sensor


3. Starting point 4. Arrival point 5. New nominal trajectory

If tracking is enabled with the SENSOR_TRK(TRUE) option, the action changes since
this option makes it possible to leave the robot enslaved to the sensor, without a
programmed move and during the interruption. Looking again at the example in the case
of SENSOR_TRK(TRUE), a behaviour that is just the same as in Fig. 8.1 - Programmed
trajectory and sensors control can be noted notwithstanding that the fly and the

pr-0-0-gpr_10.fm
108 08/1012
Sensor Tracking (optional feature)

ADVANCE have been removed; in other words, no interruption takes place on p2. The
resetting will take place the moment the enslaving condition is interrupted with the
SENSOR_TRK(FALSE) or $SENSOR_ENBL:=FALSE instruction.
This indicates that the Built-In SENSOR_TRK(TRUE) can be used to avoid the resetting
of deviations on points where the robot stops (where there is no fly).

8.9.2 Suspended sensor tracking session


There are some cases where it is necessary to ignore the sensor corrections along a
complete move although keeping the deviations acquired up to that moment. This can
be obtained by setting $SENSOR_TYPE:=0 along the move involved (obviously
interruption must be avoided linking the movements in fly or entering
SENSOR_TRK(TRUE)). Fig. 8.11 - Suspended sensor tracking session illustrates this
operation.

Fig. 8.11 - Suspended sensor tracking session

1. Programmed trajectory 2. Trajectory controlled by sensor 3. Suspended sensor tracking

8.9.3 Resetting in spread condition


Resetting in spread is the opposite condition to the suspension of a sensor tracking
session. The latter allows the deviations to be kept along a linked move in fly, whereas
the resetting in spread allows the progressive resetting of deviations terminating the
move very close to the nominal programmed point. It is usually used by introducing an
interruption (as illustrated in Fig. 8.10 - Interrupted sensor tracking session); however
where it is necessary to keep the fly between the moves the $SENSOR_ENBL variable
can be set with the FALSE value, resetting mode in spread, along the move; this can
also be obtained using the WITH clause on the required move. During the move the
sensor is ignored. The effect is shown in Fig. 8.12 - RESETTING SPREAD during a
Move.

pr-0-0-gpr_10.fm
08/1012 109
Sensor Tracking (optional feature)

Fig. 8.12 - RESETTING SPREAD during a Move

1. Programmed trajectory 2. Trajectory controlled by sensor 3. OFFSET RESET without interrupt

Tab. 8.4 - $SENSOR_TYPE allowed values

$SENSOR_TYPE SIGNIFICANCE
0 Sensor suspended
1 Seam-tracking sensor in TOOL reference (NOT AVAILABLE in
1.0 sw version)
2 Seam-tracking sensor in WEAVING reference (NOT AVAILABLE
in 1.0 sw version)
5 External sensor in TOOL reference, relative mode
6 External sensor in UFRAME reference,relative mode
7 External sensor in WORLD reference, relative mode
8 External sensor in WEACING reference, relative mode
9 External sensor in TOOL reference, absolute mode
10 External sensor in UFRAME reference, absolute mode
11 External sensor in WORLD reference, absolute mode
12 External sensor in WEAVING reference, absolute mode
13-14 Reserved
15 Reserved for the management of a certain type of laser camera
16-30 Reserved

8.9.4 Limitations in parameter changes


When using the sensor tracking there are some conditions that would cause
discontinuity in the move, and that are therefore monitored by error messages.
– It is not possible to enable sensor tracking on joint type moves; therefore
$SENSOR_ENBL has to be set to FALSE before executing the move.
– A joints move cannot be linked in fly, nor be in ADVANCE, with Cartesian moves
where sensor tracking was enabled. In the same way a joints move cannot follow
an enslaving phase without a programmed move before the Built-In
SENSOR_TRK(FALSE) has been executed to disable it.
– In the absolute tracking mode ($SENSOR_TYPE=9, 10, 11 or 12) the $BASE,
$TOOL, $USER or $SFRAME cannot be changed without interrupting the sensor

pr-0-0-gpr_10.fm
110 08/1012
Sensor Tracking (optional feature)

tracking session (see par. 8.9.1 Interrupted sensor tracking session on page 108).
On the other hand, the change of reference systems in relative modes does not
create any problems.
– It is not permitted to change from relative modes to absolute or vice-versa, without
interrupting the Sensor Tracking session. In the same way, it is not possible, in
absolute modes, to change the type of reference system in which the tracking is
required, without interrupting the enslaving (see par. 8.9.1 Interrupted sensor
tracking session on page 108).

8.10 Programming example


Below the program already given in the par. 8.1 Principle of operation on page 94 is
shown, completed with the instructions needed to configure and enable the sensor
tracking. It is assumed to use an external sensor mounted on the torch that is able to
calculate corrections in Y an Z directions in relation to the TOOL reference. The system
variables that are not shown in the example are left at their default value. The
GET_CORR routine, that is not indicated, will be written in PDL2 so as to read the
information of the sensor, process it and copy it in the two corr_y and corr_z.
parameters

PROGRAM sensor
VAR
p1, p2, p3, p4:POSITION
corr_y, corr_z:REAL
corr, ofst:ARRAY[6] OF REAL

ROUTINE send_corr
BEGIN
get_corr(corr_y, corr_z)
corr[2]:=corr_y; corr[3]:=corr_z
SENSOR_SET_DATA(corr)

SENSOR_GET_OFST(ofst)
WRITE (‘X:‘, ofst[1], ‘ Y; ‘, ofst[2], ‘ Z: ‘, ofst[3], NL)

$TIMER[1] := 0
ENABLE CONDITTRUE[1]
END send_corr

BEGIN
CONDITION[1] :
WHEN $TIMER[1] > 500 DO
send_corr --Corrections sent every 500 ms
ENDCONDITION
corr[1]:=0; corr[2]:=0; corr[3]:= 0
corr[4]:=0; corr[5]:=0; corr[6]:= 0

--Sensor tracking environment configuration


$SPD_OPT := SPD_LIN --to check linear speed
$LIN_SPD := 0.1 --Linear speed in m/s

pr-0-0-gpr_10.fm
08/1012 111
Sensor Tracking (optional feature)

$SENSOR_TYPE := 5 --External sensor in relative mode and TOOL


reference

$SENSOR_CNVRSN[2] := 0.2 --Example of Y conversion factor


$SENSOR_CNVRSN[3] := 0.2 -- Example of Z conversion factor

$SENSOR_GAIN[2] := 60 -- Example of Y gain


$SENSOR_GAIN[3]:= 80 -- Example of Z gain

$SENSOR_TIME := 500 -- Deviation distribution in time

$SENSOR_OFST_LIM[1] := 50 --Translation maximum limit

-- Program in movement
MOVE JOINT TO p1

-- Sensor tracking session


$TIMER[1] := 0
ENABLE CONDITION[1]
$SENSOR_ENBL := TRUE

MOVEFLY LINEAR TO p2 ADVANCE


MOVE LINEAR TO p3

$SENSOR_ENBL := FALSE
DISABLE CONDITION[1]

MOVE JOINT TO p4

END sensor

pr-0-0-gpr_10.fm
112 08/1012
Conveyor Tracking (optional feature)

9. CONVEYOR TRACKING
(OPTIONAL FEATURE)

Conveyor Tracking
The option code is CR17926206.

The Conveyor Tracking environment allows the user to write simple programs for
reaching positions defined on a moving conveyor-truck: the C5G Controller
automatically compensates the istantaneous position of the conveyor.
In order to compute the instantaneous position of a truck, the conveyor motor has to be
equipped with a position transducer connected to C5G Controller Unit.
Up to four conveyors can be handled. When the tracking is enabled, only cartesian
movements can be executed.
Two kinds of tracking are available:
– Cartesian Tracking - in this case the of cartesian tracking the robot is fixed and
the conveyor tracking is done using a dynamic conveyor frame (truck frame) that
will be shifted according to the position of the truck. In this way, it is possible to track
trucks mounted on traversing or rotating conveyors involving, in the first case linear
Cartesian tracking and, in the second, circular Cartesian tracking. They are no
restrictions regarding the placement and orientation of the conveyor. Since the
robot is fixed and the workpiece moves, the workspace is reduced (the robot can
work on the part for a very short time) so that the cartesian tracking is
recommended for pick and place applications.
– Rail Tracking - this kind of tracking can be used when the robot is mounted on
a slide. In this case the slide is used to track and therefore the conveyor must be
of the linear type and the rail must be parallel to this. The rail motion will be the sum
of two components:
• a tracking component
• a component due to the programmed motion.
Thus, the rail tracking increases the workspace of the robot and allows to work on
huge parts controlling the tool speed and orientation.
This chapter describes the following subjects :
– Configuration
– Working Principle
– Process Monitoring
– Tracking Window
– Motion Statements
– Teaching Positions
– Tracking Interruption
– Limitations during Conveyor Tracking
– Use of the Roto-translating Conveyor

pr-0-0-gpr_11.fm
08/1012 113
Conveyor Tracking (optional feature)

9.1 Configuration
Use IO_CNFG program (Chap.12.1 in USE of C5G Control Unit manual -
par.Conveyor Tracking Kit), to configure conveyor tracking and define any associated
kit to the conveyor itself.
Then, enter the Conveyor subpage within the SETUP page on the Teach Pendant, to
set the basic parameters (par.5.17.7 - Conveyor (optional feature) in USE of C5G
Control Unit manual).
System variables to configure the conveyor tracking are fields of $TRK_TBL data
structure which is an array of basic structures to handle the tracking functionalities.
To configure the hardware link of the conveyor to C5G Controller ,the following variables
are available:
– $TRK_TBL[nTbl].TT_APPL_ID identifies the being configured application type
(conveyor = 2):
$TRK_TBL[nTbl].TT_APPL_ID := 2
– $TRK_TBL[nTbl].TT_PORT_TYPE[1] identifies the input port type which has been
connected to the position transducer (it is a $FMI port, identified by number 27):
$TRK_TBL[nTbl].TT_PORT_TYPE[1] := 27
– $TRK_TBL[nTbl].TT_PORT_IDX[1] identifies the configured port index, for reading
the position transducer. In case of predefined kit, such an index is automatically
assigned by the system. In case of user kit, the user should specify an already
mapped $FMI index.
– In the case in which the position transducer is an encoder, the transducer sin/cos
pulse number must be specified by means of the following statement:
$TRK_TBL[nTbl].TT_I_PRMS[1] := 0 -- resolver
$TRK_TBL[nTbl].TT_I_PRMS[1] := 1024 -- encoder
– As far as the transmission rate, the following statement must be used:
$TRK_TBL[nTbl].TT_R_PRMS[1] := <tx_rate_value>
its unit of measure is [mm/motor turns] for cartesian linear tracking, rototranslating
tracking, or rail tracking, whereas it is [motor turns/table turns] for rotating
conveyors.
– The being configured conveyor type must be specified by means of the following
statement:
$TRK_TBL[nTbl].TT_I_PRMS[2] := <conv_cnfg_value>
where <conv_cnfg_value> can be as follows:
• 0: linear cartesian tracking;
• 1: circular cartesian tracking;
• 3: rototranslating cartesian tracking (Robot Control on a ad una
bending-press).
• 4: rail tracking with positive direction of the robot slide in the positive direction
of the conveyor;
• 5: rail tracking with negative direction of the robot slide in the positive direction
of the conveyor.
– In case of either circular or rotranslating conveyor, the conveyor radius is also to
be specified, which can be run-time modified, by means of the following statement:
$TRK_TBL[nTbl].TT_R_PRMS[2] := <conveyor_radius>

pr-0-0-gpr_11.fm
114 08/1012
Conveyor Tracking (optional feature)

– More than one Arm can be configured on the same Controller and not necessarily
they all neither are intended to track a conveyor nor it is right to use them for
tracking; a bit mask must then be configured indicating to the C5G which are the
enabled Arms for tracking, by means of the following statement:
$TRK_TBL[nTbl].TT_ARM_MASK := <arm_mask>
Only the Arms which are included in the bit mask, will be enabled for tracking; an
error message will occur for the other ones, if and when there is an attempt to
activate the conveyor.
– For a good robot conveyor tracking, the reference frame must be defined on the
conveyor base:
$TRK_TBL[nTbl].TT_FRAMES[1] := <base1>
$TRK_TBL[nTbl].TT_FRAMES[2] := <base2>
$TRK_TBL[nTbl].TT_FRAMES[3] := <base3>
There are 3 reference values for the conveyor, with the following use:
1. <base1> is used for all the different conveyor types except the rototranslating
one for which such a reference frame is only used during the press linear
tracking;
2. <base2> is used to upwards track the press during the press-bending
movement;
3. <base3> is used to downwards track the press during the press-bending
movement.
To discriminate between the three <baseX>, in case of rototranslating conveyor, it
is needed to set the following run-time modifiable variable, before activating
tracking:
$TRK_TBL[nTbl].TT_I_PRMS[3] := <modality>
Where the allowed values for such a variable are as follows:
• 0: press linear tracking;
• 1: rototranslation upwards tracking;
• 2: rototranslation downwards tracking.
It must be measured when the truck is either in the zero position (see later) or in a
known position. Some criteria must be complied in choosing the reference origin
position and the axes direction, which are slightly different for either linear, circular
or rototranslating tracking. See also par. 9.9 Use of the Roto-translating Conveyor
on page 123.
In case of linear conveyors, the base reference X axis must be aligned to the
positive direction of the conveyor; the X-Y plane must coincide with the plane of the
truck and the origin must be positioned at the point in which a sensor detects
passing of the truck.
In case of circular conveyors, the X axis must be tangential to the rotating table; the
Y axis must be in radial direction in relation to the table and oriented towards the
center of rotation; the position of the Z axis comes from the first two axes according
to the right-hand rule and faces up if the rotating table turns anticlockwise and
down otherwise. In circular case, the reference system origin must be at a known
distance from the center of rotation and does not precisely coincide with this; this
distance represents the table radius and must be assigned to
$TRK_TBL[nTbl].TT_R_PRMS[2]
(in case of rototranslating Conveyor, see par. 9.9 Use of the Roto-translating
Conveyor on page 123). The circumference passing through the table base
reference origin plays an important role in managing rotations: all distances and

pr-0-0-gpr_11.fm
08/1012 115
Conveyor Tracking (optional feature)

speeds are measured in relation to this base circumference.


– The maximum allowed value for robot acceleration and speed can be configured
during the tracking phases, by means of the following statements:
$TRK_TBL[nTbl].TT_R_PRMS[3] := <speed_limit>
$TRK_TBL[nTbl].TT_R_PRMS[4] := <acceleration_limit>
– Furthermore, two tracking windows can be defined by means of the following
statements:
$TRK_TBL[nTbl].TT_R_PRMS[5] := <first_value>
$TRK_TBL[nTbl].TT_R_PRMS[6] := <second_value>
Where <first_value> indicates the conveyor quote from which the robot must
start tracking, whereas <second_value> indicates the quote beyond which no
tracking can be performed by the robot.
– A virtual encoder can be configured, i.e. to activate the conveyor on an input port
by setting the following variable:
$TRK_TBL[nTbl].TT_R_PRMS[17] := <conversion_factor>
Such a variable, if not zero, activates tracking by means of an input port, even
without any hardware conveyor and represents the conversion factor from the input
port unit of measure and the conveyor unit of measure (without taking the
<tx_rate_value> into account, which should anyway be indicated).

9.2 Working Principle


The conveyor is not controlled by C5G Controller but only monitored by reading the
position of the position transducer, connected to the motor of the conveyor and linked
with the servo board of C5G Controller. The position transducer value is stored in the
following variable
$CRNT_DATA[narm].CONV_ENC[nTbl]
every interpolation tick.
At a certain distance from the working area, a sensor (e.g. a photocell) must be placed
to detect the passage of the conveyor-truck.
This is the zero position and when the truck goes through it, the calibration (zeroing) of
the conveyor position is needed, by means of the CONV_TRACK built-in (see PDL2
Programming Language manual - chap.11 BUILT-IN Routines List), which can also
be called from within the Conv environment in the Motion Page of the Teach Pendant
(par.5.9.8 - Conveyor Tracking (optional feature) of C5G Control Unit Use).
At every interpolator tick, the system calculates the truck current position and updates
the frame reference system shifting it along X+ of the distance indicated by

$CRNT_DATA[n].CONV_SHIFT[nTbl]
Such a distance is in millimeters. When tracking is active, the User frame (indicated by
$UFRAME) is referred to the truck frame, so that all the POSITIONs are referred to the
moving workpiece (see Fig. 9.1 - Reference Frames for linear Cartesian tracking on rail
and Fig. 9.2 - Reference Frames for circular tracking).

pr-0-0-gpr_11.fm
116 08/1012
Conveyor Tracking (optional feature)

Fig. 9.1 - Reference Frames for linear Cartesian tracking on rail

1. Tracking Window 2. User Frame


3. Conveyor Base Frame 4. Slide Frame
5. World Frame 6. Sensor

Fig. 9.2 - Reference Frames for circular tracking

1. User Frame 2. Conveyor Base Frame


3. User Frame 4. Slide Frame
5. Sensor 6. User Frame

In case of rail tracking, the $CRNT_DATA[n].CONV_SHIFT[nTbl] value is added to the


current position of the robot rail and the result is that the world frame of reference is
moved together with the conveyor.

pr-0-0-gpr_11.fm
08/1012 117
Conveyor Tracking (optional feature)

9.3 Process Monitoring


For the conveyor monitoring, some arrays are used in $CRNT_DATA:
– Number of the active conveyor on the Arm (0=none)
$CRNT_DATA[narm].CONV_ACT
– Conveyor encoder position in turns --> $CRNT_DATA[narm].CONV_ENC[nTbl]
– Bend angle of the rototranslating conveyor, in radians
$CRNT_DATA[narm].CONV_BEND_ANGLE[nTbl]
This allows monitoring of all the configured conveyors by all the arms which are enabled
to work with the conveyor; such a monitoring will always result active, regardless of the
conveyor state.
Since $CRNT_DATA[n].CONV_DIST[nTbl] is an INTEGER variable, it can be inserted more
effectively than $CRNT_DATA[n].CONV_SHIFT[nTbl] in a CONDITION to guarantee
maximum efficiency.

Note that the Control Unit considers the speed of the slide to be null if its motion is
reversed.

9.4 Tracking Window


For further information, please refer to par.5.17.7.1 - Tracking Table editing
procedure - Cinematics subpage, in C5G Control Unit Use manual.

The tracking window is a region that defines where the robot is enabled to track the
workpiece.
The tracking window has a start limit and an end limit, defined by the following system
variables
$TRK_TBL[nTbl].TT_R_PRMS[5] and
$TRK_TBL[nTbl].TT_R_PRMS[6].
$TRK_TBL[nTbl].TT_R_PRMS[5] contains the start limit from the origin of the conveyor
base frame (where the sensor is placed), whereas $TRK_TBL[nTbl].TT_R_PRMS[6]
contains the final limit distance (in case of rotating table, such distances are read along
the base circumference).
When tracking is active, no motion will begin until the origin of the truck frame is inside
the tracking window. If the robot attempts to move to a position when the truck has not
reached the window yet, the Controller waits until the part enters the window, which
means until $CRNT_DATA[n].CONV_SHIFT[nTbl] is greater than
$TRK_TBL[nTbl].TT_R_PRMS[5].
If the robot attempts to move when the truck is already out of the window
($CRNT_DATA[n].CONV_SHIFT[nTbl] > $TRK_TBL[nTbl].TT_R_PRMS[6]), an error is
issued by the Control Unit. The tracking window is usually defined during the
configuration phase, moving the robot to the two limits.

pr-0-0-gpr_11.fm
118 08/1012
Conveyor Tracking (optional feature)

9.5 Motion Statements


The conveyor configuration does not depend on the arm, i.e. only a group of arms will
be indicated as being enabled to track the conveyor. This means that several arms can
work on the same conveyor both at the same time and consecutively, upon the required
application and the user programs.
It is then needed to activate and deactivate the conveyor in association to a specified
arm. To execute such an association, the following built-in routine is available:
CONV_TRACK(cmd, nTbl, <narm>, <dist>)
where the parameters have the following meaning:
– cmd - conveyor command assuming one of the following values:
• -1 initialize (CONV_INIT)
• 0 deactivate (CONV_OFF)
• 1 initialize and activate (CONV_INIT_ON)
• 2 activate (CONV_ON)
– nTbl - number of the configured table for the conveyor;
– narm - number of the arm for doing the conveyor tracking; it is an optional
parameter; if missing, the used value is the prog_arm;
– dist - distance between the sensor and the being tracked object, at the time in
which the conveyor initialization is requested; the default value is 0
If, before such a built-in is called, some configuration parameters are modified, it
updates the data in order to perform a good tracking.
Such a built-in routine execution, depending on the assigned value to cmd parameter,
activates/deactivates tracking without putting to zero the the conveyor encoder quote if
CONV_ON command is issued.
CONV_INIT_ON command puts to zero the conveyor quote and immediately activates
the conveyor; on the contrary, CONV_INIT command puts to zero the conveyor quote
without activating it. To deactivate it, CONV_OFF command is to be used.
If on the arm a conveyor tracking operation is already active, the built-in routine returns
an error when the user attempts to either initialize or activate a new conveyor.
A sample program follows to pick pieces from a conveyor and place them to a table:

PROGRAM conv
BEGIN
CONDITION[1]:
-- for example, the sensor is connected to $DIN[[1]
WHEN $DIN[1] DO
CONV_TRACK(-1, 1) - azzeramento conveyor da tabella 1
ENDCONDITION
CYCLE
ENABLE CONDITION[1]
WAIT FOR $DIN[1] -- wait for a workpiece
CONV_TRACK(2, 1) -- enable tracking
MOVEFLY LINEAR NEAR P1 BY 100 ADVANCE -- moving towards
-- the truck
MOVE LINEAR TO P1 -- moving on the workpiece
CLOSE HAND -- pick
MOVE LINEAR NEAR P1 BY 100 -- move to the track

pr-0-0-gpr_11.fm
08/1012 119
Conveyor Tracking (optional feature)

MOVE LINEAR TO P1 -- move to the workpiece


CLOSE HAND -- pick
MOVE AWAY 100
CONV_TRACK(0, 1) -- disable tracking
MOVEFLY LINEAR NEAR P2 BY 100 ADVANCE -- moving on the table
MOVE LINEAR TO P2
OPEN HAND -- release workpiece
MOVE AWAY 100
END conv

9.6 Teaching Positions


Teaching cannot be performed when the conveyor is moving since tracking is not
allowed in Programming state.
Before starting the teaching session, CONV_TRACK built-in routine must be executed
with the zeroing command (with immediate activation if needed). The best method is to
switch the conveyor off after the passage through the zero position has been detected
and the CONV_TRACK built-in routine has been properly executed.
Otherwise the user has to measure the distance between the workpiece and the sensor
and then assign the zero position by the CONV_TRACK built-in, indicating the optional
parameter <dist>, where dist is the measured distance (in case of circular tracking it is
calculated along the circumference).
In Programming state and conveyor tracking enabled, every time a move starts the
position transducer is read and the cartesian positions are updated.

9.7 Tracking Interruption


LOCK statement and some alarms due to the motion, stop the program execution, but
the robot continues its tracking; this means that the robot moves in order to maintain
held the TCP with respect to the moving truck.
Fatal alarms, HOLD and DRIVES OFF commands stop both the execution of the
program and tracking. An output signal should be issue in order to stop and restart the
conveyor motion.

9.8 Limitations during Conveyor Tracking


All cases of Conveyor Tracking involve a number of limitations:
– only Cartesian (linear or circular) trajectories on POSITION type points can be
carried out during tracking;
– as joint type movements are not allowed, the recovery trajectories must also be of
the Cartesian type. Therefore, the values of the $RCVR_TYPE variable may be 3,
4, 5 , 6 only;
– no active motions can be present, when CONV_TRACK built-in routine is called to
activate or deactivate tracking;

pr-0-0-gpr_11.fm
120 08/1012
Conveyor Tracking (optional feature)

– it is not possible to check tolerances on the stopping points during tracking as the
movement of the carrier involves continuous movement of the axes of the robot
also during stoppages. Therefore the only permissible value of the $TERM_TYPE
system variable is NOSETTLE;
– the values of $BASE and $TOOL variables cannot be modified immediately before
the carrier release movement. $UFRAME can however be modified as required;
– a linear trajectory on the fixed positions, i.e. with $CONV_TYPE := CONV_OFF
must be carried out after any error that causes release of robot trajectory;
– it is not possible to restart tracking after a power failure without first of all bringing
the robot to a fixed position (i.e. executing CONV_TRACK built-in with CONV_OFF
command).
– it is recommended not to use the CONV_TRACK built-in as the first statement in a
HOLDABLE program.

Tab. 9.1 - Conveyor Tracking System Variables


Tab. 9.2 -
Name Description Type
Identifier of the being configured tracking application type:
TT_APPL_ID INTEGER
conveyor = 2
Several arms can be configured on the same Controller and not
necessarily they all are to track the conveyor, or sometimes it is
not correct to use them for tracking; it is then needed to also
configure a bit mask indicating to C5G which are the enabled
TT_ARM_MASK arms for tracking, by means of the following statement: INTEGER
$TRK_TBL[nTbl].TT_ARM_MASK := <arm_mask>
Only the arms which are in cluded in the mask are allowed to do
the conveyor tracking; for the other ones an error message
occurs on attempts to activate the conveyor.
For the robot to properly track the conveyor, it is needed to
define a reference frame on the conveyor base:
$TRK_TBL[nTbl].TT_FRAMES[1] := <base1>
$TRK_TBL[nTbl].TT_FRAMES[2] := <base2>
$TRK_TBL[nTbl].TT_FRAMES[3] := <base3>
There are three reference values for the conveyor, with the
following meaning:
1 <base1> is used for several conveyor types except the
rototranslating one, for which such a reference is only used
during the press linear tracking;
2 <base2> is used to track the press upwards during the ARRAY[3] OF
TT_FRAMES
press-bend movement; POSITION
3 <base3> is used to track the press downwards during the
press-bend movement.
In case of linear conveyors, the X axis of the base reference
frame, must be aligned to the positive motion direction of the
conveyor; X-Y plane must match with the truck plane direction
In the circular case, axis X must be tangent to the rotating table;
axis Y must be in radial direction referred to the table and
oriented towards the rotation center; the Z axis comes from the
X and Y ones, using the right hand rule and it is upwards if the
table moves anticlock wise, downwards on the contrary. In case

pr-0-0-gpr_11.fm
08/1012 121
Conveyor Tracking (optional feature)

Tab. 9.2 -
Name Description Type
of circular tracking, the reference system origin must be at a
known distance from the rotation center and not exactely
corresponding to it; this distance represents the table radius and
must be assigned to TT_R_PRMS[2] variable.
INTEGER parameters for tracking configuration
– TT_I_PRMS[1] sin/cos pulse number
– TT_I_PRMS[2] conveyor configuration (linear, circular, rail
tracking, rototranslating conveyor )
– TT_I_PRMS[3] rt modality
In order to discriminate among the different BASEs
(see TT_FRAMES), in case of rototranslating conveyor, it is
needed to set the following variable, run-time editable, before
activating tracking:
$TRK_TBL[nTbl].TT_I_PRMS[3] := <modality>
ARRAY[20] OF
TT_I_PRMS where the allowed values to be assigned to the variable are as INTEGER
follows:
– 0: press linear tracking;
– 1: rototranslation upwards tracking;
– 2: rototranslation downwards tracking.
It must be measured when the truck is either in the zero position
(see later) or in a known position. Some criteria must be complied
with in choosing the reference origin position and the axes
direction, which are slightly different for either linear, circular or
rototranslating tracking. See also par. 9.9 Use of the
Roto-translating Conveyor on page 123.
I/O port index for tracking:
TT_PORT_IDX ARRAY[5] OF INTEGER
– TT_PORT_IDX[1] port number for conveyor encoder
I/O port type code for tracking:
TT_PORT_TYPE ARRAY[5] OF INTEGER
– TT_PORT_TYPE[1] port type for conveyor encoder
REAL parameters for tracking configuration
– TT_R_PRMS[1] tx_rate
– TT_R_PRMS[2] radius (circular / roto-traslanting)
– TT_R_PRMS[3] speed limit
– TT_R_PRMS[4] acceleration limit
– TT_R_PRMS[5] tracking window start limit
– TT_R_PRMS[6] tracking window end limit
– TT_R_PRMS[7] sheet depth in mm
TT_R_PRMS – TT_R_PRMS[8] die cave angle in rad ARRAY[20] OF REAL
– TT_R_PRMS[9] die shoulder radius in mm
– TT_R_PRMS[10] die cave width in mm
– TT_R_PRMS[11] knife radius in mm
– TT_R_PRMS[12] Maximum bend rotation angle in rad
– TT_R_PRMS[13] parameter 1 for arma filter
– TT_R_PRMS[14] parameter 2 for arma filter
– TT_R_PRMS[15] arma_filter_3 (rt)
– TT_R_PRMS[16] arma_filter_4 (rt)

pr-0-0-gpr_11.fm
122 08/1012
Conveyor Tracking (optional feature)

Tab. 9.3 - Conveyor Tracking Built-ins

Built-in name Parameters


CONV_TRACK cmd, nTbl, <narm>, <dist>
Where:
– cmd - conveyor command with the following
allowed values:
• -1 initialize (CONV_INIT)
• 0 deactivate (CONV_OFF)
• 1 initialize and activate (CONV_INIT_ON)
• 2 activate (CONV_ON)
– nTbl - number of the configured table for
conveyor
– narm - optional; number of the arm to be used for
conveyor trackin operations; if missing, the
prog_arm is used
– dist - optional; distance between the sensor and
the being tracked object, at the time the conveyor
initialization is required; the default value is 0.

9.9 Use of the Roto-translating Conveyor


Usually, $TRK_TBL[nTbl].TT_FRAMES, frame cannot be permanently calculated at the
configuration time, because it depends on the bend upward or downward direction.
Anyway, it is possible to fix some headlines which could be useful to determine it.
The X axis of the base frame must be lined up with the Conveyor motion direction (which
means the knife of the bending-press); the X-Y plane must be orthogonal to the
bending-press motion plane and the origin must be fixed in the maximum opening point
of the bending-press.
If the bend direction of the part is upward, the Y axis must enter the bend motion plane;
on the contrary, it must exit the motion plane.
The value of $TRK_TBL[nTbl].TT_R_PRMS[2] is the robot distance from the bend (in
mm); such a value must be calculated referred to the robot position at the beginning of
the bend, from the sheet point of contact (see Fig. 9.3).

Fig. 9.3 - Bend beginning position

1. Bending-press 2. Sheet 3. Robot

pr-0-0-gpr_11.fm
08/1012 123
Conveyor Tracking (optional feature)

Fig. 9.4 - Bending Press 3-dimensional representation

Fig. 9.5 - Bending Press graphical representation

pr-0-0-gpr_11.fm
124 08/1012
Conveyor Tracking (optional feature)

9.9.1 Configuration parameters


The needed parameters to properly configure the tracking, are as follows:

$TRK_TBL[nTbl].TT_R_PRMS[7] Sheet depth in mm


$TRK_TBL[nTbl].TT_R_PRMS[8] Die cave angle in rad
$TRK_TBL[nTbl].TT_R_PRMS[9] Die shoulder radius in mm
$TRK_TBL[nTbl].TT_R_PRMS[10] Die cave width in mm
$TRK_TBL[nTbl].TT_R_PRMS[11] Knife radius in mm
$TRK_TBL[nTbl].TT_R_PRMS[12] Maximum bend rotation angle in rad

pr-0-0-gpr_11.fm
08/1012 125
Motion with Weaving (optional feature)

10. MOTION WITH WEAVING (OPTIONAL


FEATURE)

Weaving Motion
The option code is CR17926207.

Weaving is an oscillating motion superimposed on a Cartesian trajectory. It is useful for


arc-welding applications and some gluing and sealing applications. Weaving is a
method used to distribute material in gaps with large cross sections relative to the
material bead.
Weaving can be superimposed on any Cartesian motion (either linear or circular) or
multiple motions connected in fly. The shape of the weaving pattern is defined by a set
of parameters (parametric weaving). Two modes of weaving are available, cartesian
weaving and joint weaving.
The subjects described in this chapter are the following :
– Weaving Mode
– Weaving Activation
– Weaving Parameters
– Stopping Motions with Weaving
– Programming Weaving
– Weaving without Arm motion
– Weaving on multiarm systems.

10.1 Weaving Mode


The weaving mode can be selected through the $WEAVE_TYPE variable Leaving this
variable set at default value zero, cartesian weaving is selected. In this mode, weaving
is defined relative to a frame determined by the trajectory itself and is not affected by
changes in tool orientation along the trajectory. If $WEAVE_TYPE is assigned a value
between 1 and 10, the selected weaving is joint mode. In this case, the value of the
predefined variable indicates the axis on which the weaving is performed and the
weaving direction depends on the position of all axes. Joint weaving allows higher
weaving frequencies than cartesian weaving.

10.2 Weaving Activation


Weaving is activated and deactivated using the predefined variable $WEAVE_NUM.
This variable contains the number of the active weave table. The default value of 0
means that weaving is disabled.
Weaving is activated by simply assigning the index number of the desired weave table
to $WEAVE_NUM. All succeeding Cartesian movements will be performed using the

pr-0-0-gpr_09.fm
126 08/1012
Motion with Weaving (optional feature)

weaving parameters of the active $WEAVE_TBL[$WEAVE_NUM] table.


It is possible to weave during a series of continous motions (fly) or along a path motion.
However, weaving will only occur during the Cartesian motions or Cartesian path
segments. If a series of fly motions or a path includes a joint interpolated motion,
weaving will stop during the joint motion and then start again with the next Cartesian
motion or path segment.
The first move with weaving is the movement after a weaving stop. A weaving stop can
occur if the user disables it intentionally, or if the movement is a joint motion, or if two
moves with weaving are not linked with a continuous motion (fly). This principle is
applied not only to singular motions, but also in case of path segments (PATH).

10.3 Weaving Parameters


$WEAVE_TBL predefined variable is used to define all the weaving characteristics.
$WEAVE_TBL is an array of records that allows a user to define up to 10 different weave
tables. The fields of $WEAVE_TBL are defined as follows:
– $WEAVE_MODALITY the weaving wave form generation modality. It is an
INTEGER with possible values 0,1 and 2 :E’ un INTEGER con valori da 0 a 4
• $WEAVE_MODALITY=0 - the wave form is generated by the transverse
speed;
• $WEAVE_MODALITY=1 - the wave form is generated by the wavelength. In
this case the wave form does not change as the overrides related to the feed
speed vary;
• $WEAVE_MODALITY=2 - the wave form is generated with 4 different
transverse speeds, to produce asymmetrical profiles.
• $WEAVE_MODALITY=3 weaving con forma d'onda circolare generato dalla
velocità trasversale.
• $WEAVE_MODALITY=4 weaving con forma d'onda circolare generato dalla
lunghezza d'onda.
– an INTEGER field defines the wave length in the weaving form:
• $WV_LENGTH_WAVE (from 0 to 10.000 mm);
– two REAL fields define the left and right amplitudes, in case of trapezoidal weaving:
• $WEAVE_TBL[n].WV_LEFT_AMP defines the left amplitude (0 - 20),
• $WEAVE_TBL[n].WV_RIGHT_AMP defines the right amplitude (0 - 20);
– two REAL field define the circular wave form:
• $WEAVE_TBL[n]. WV_RADIUS defines the weaving amplitude (in mm) in the
trajectory direction in case of circular weaving (it is the semi-minor axis of the
ellipse representing the weaving form).
• $WEAVE_TBL[n]. WV_AMPLITUDE defines the weaving amplitude (in mm)
in the direction perpendicular to the trajectory in case of circular weaving (it is
the semi-major axis of the ellipse representing the weaving form).
– four INTEGER fields define the dwell time:
• $WEAVE_TBL[n].WV_LEFT_DWL defines the dwell time (in ms) on the left;
if $WEAVE_MODALITY=1 it defines the distance covered (in mm) on the left
along the path. Limits: from 0 to 10,000;
• $WEAVE_TBL[n].WV_CNTR_DWL defines the dwell time (in ms) in the
centre; if $WEAVE_MODALITY=1 it defines the distance covered (in mm) at
the centre along the path. Limits: from 0 to 10,000;

pr-0-0-gpr_09.fm
08/1012 127
Motion with Weaving (optional feature)

• $WEAVE_TBL[n].WV_RIGHT_DWL defines the dwell time (in ms) on the


right; if $WEAVE_MODALITY=1 it defines the distance covered (in mm) on
the right along the path. Limits: from 0 to 10,000;
• $WEAVE_TBL[n].WV_END_DWL defines the dwell time (in ms) at the end of
the move; if $WEAVE_MODALITY=1 it defines the distance covered (in mm)
at the end of the move, along the path. Limits: from 0 to 10.000;
– a BOOLEAN field controls the corners smoothness of the wave shape (see
explanation below):
• $WEAVE_TBL[n].WV_SMOOTH ;
– a REAL field controls the transverse speed:
• $WEAVE_TBL[n].WV_TRV_SPD (recommended 0.035 m/sec);
– four REAL fields for the four transverse speeds that are used in modality 2:
• $WEAVE_TBL[n].WV_TRV_SPD_PHASE[m]; (con 1<=m<=4)
– a REAL field defines the weave plane and weave direction (see explanation
below):
• $WEAVE_TBL[n].WV_PLANE (from -180 to +180 degrees);
– an INTEGER field for the weaving plane evolution modality:
• $WEAVE_TBL[n].WV_PLANE_MODALITY defines the modality in which the
weaving plane is calculated. If this variable is set to 0 (default), the weaving
plane is kept constant compared to the sequence of the fly connected
trajectories. If this variable is set to 1, the weaving plane is calculated on the
trajectory and it is integral with the tool and perpendicular to it;
– a REAL field for the weaving direction:
• $WEAVE_TBL[n].WV_DIRECTION_ANGLE defines the allowed angle for
the weaving direction in case of either Weaving without Arm motion or in case
of weaving plane integral with the tool. The default direction (angle 0)
corresponds to the TOOL X direction;
– an INTEGER field defines the weave amplification factor (%):
• $WEAVE_TBL[n].WV_AMP_PER (from 0% to 1000%);
– a BOOLEAN field indicates that the acceleration and deceleration characteristics
are used
• $WEAVE_TBL[n].WV_SPD_PROFILE; using this function the transverse
speeds are reached with a ramp, so as to remain within the
acceleration/deceleration limits of the axis involved in the weaving, for joints
weave; or within Cartesian acceleration/deceleration limits for Cartesian
weave. Furthermore, a test is made on the maximum speed that can be
reached.
Index n varies from 1 to 10 and the user can change a range of the 10
elements of the table at any time
Parametric weaving is defined by three indications:
– Wave Shape
– Weave Plane (angle of weaving plane)
– Weave Amplification (used to vary the weaving amplitude)

10.3.1 Wave Shape


The basic weave pattern can be either trapezoidal or circular. The units of measurement
of some fields of $WEAVE_TBL depend upon the type of selected weaving. If cartesian

pr-0-0-gpr_09.fm
128 08/1012
Motion with Weaving (optional feature)

weaving is being used, $WV_LEFT_AMP and $WV_RIGHT_AMP, $WV_RADIUS and


$WV_AMPLITUDE are expressed in millimeters; in case of joint weaving these
parameters are expressed in degrees or millimeters depending on whether the selected
axis is rotational (degrees) or translational (mm). $WV_TRV_SPD is expressed in
meters/second when using cartesian weaving, in radians/second for a rotational axis
with joint weaving, and in meters/second for a translational axis with joint weaving.
If WEAVE_MODALITY = 0 or 3, the wave is described by the transverse speed, the
amplitude, the dwell times, and the speed along the trajectory. The frequency of the
pattern is fixed by the first three of these parameters. The motion speed along the
trajectory ($LIN_SPD) does not affect frequency, but rather the wave length. Fig. 10.1
shows the basic shape and defines the various dwell times. It also shows how the speed
and slope are calculated in case of trapezoidal wave.
If WEAVE_MODALITY = 1 or 4, the wavelength (and therefore the frequency) are
maintained as the speed varies; overrides do not influence the wave form.
If WEAVE_MODALITY=2, the wave form is generated with 4 different transverse
speeds. Profiles are asymmetric.

Fig. 10.1 - Weave Parameters - A

Note that the following formula is used for transverse speed calculation
Left amplitude
Transverse speed = ----------------------------
ts

a. Weaving direction b. Time

1 - ts[1] 2 - Left dwell time 3 - ts[2] 4 - Central dwell time


5 - ts[3] 6 - Right dwell time 7 - ts[4] 8 - Final dwell time
9 - Left amplitude 10 - Right amplitude

Meaning of the terms ts[n] (ramp up or down times), according to the weaving modality:
– Modality 0 - ts times are all equal and are generated to reach a transverse
speed $weave_tbl[n].wv_trv_spd;
– Modality 1 - the ts times are all equal and are generated to create the weaving
period according to the programmed wave length;
– Modality 2 - The ts[n] times are generated to reach the respective transverse
speeds $weave_tbl[n].wv_trv_spd_phase[n].

pr-0-0-gpr_09.fm
08/1012 129
Motion with Weaving (optional feature)

Fig. 10.2 - WeaveParameters - B

1 - Weaving direction 2 - Path 3 - Transverse speed


4 - Torch speed = Linear speed 5 - Torch speed = Resulting speed 6 - Linear speed

The amplitude, dwell, smoothness, and speed fields will take affect immediately after the
change (even during a weave motion). The direction and amplification factor will take
affect only on the first move with weaving.
When the left and right dwells are set to 0, a triangular or sawtooth wave shape results.
The sharp peaks of the sawtooth shape can be rounded to produce a sinusoid-like
shape by setting the smoothing field to TRUE. Fig. 10.3 shows the different shapes that
can be achieved using the $WEAVE_TBL settings.

Fig. 10.3 - Weave waves

1 - Not smoothed sawtooth, 2 - Smoothed sawtooth 3 - Trapezoidal (left and right dwell)
4 - Chamfering variation during motion, with central dwell time 5 - Different left and right amplitudes
6 - Circular

The weave wave frequency, according to the used modality, is calculated in one of these
ways:
– modality 0

pr-0-0-gpr_09.fm
130 08/1012
Motion with Weaving (optional feature)

– modality 2

where:
dwell sum = left dwell + right dwell + 2 * center dwell (ms)
The maximum frequency is dependent on the mechanical design of the arm, but the
weave shape will match the theoretical up to about 5 Hz (cartesian weaving) or 8 Hz
(joint weaving) on arms intended for arc welding.

Fig. 10.4 - WeaveParameters - C

The weave parameters - B (see Fig. 10.2) are valid for any wave form.
La frequenza nel caso di forma d'onda circolare descritta dalla velocità trasversale è:

10.3.2 Weave Plane


Weave plane only applies to cartesian weaving and is established as explained below.
At the beginning of the first move with weaving, the approach vector of the tool and the
tangent to the move trajectory establish a plane, called the torch plane. A plane called
the zero plane is defined perpendicular to the torch plane and contains the trajectory. (If
the motion is a straight line, then the tangent to the trajectory is the straight line. If the
motion is a circle, then the tangent to the trajectory is the tangent to the circle at its start
point). If the torch approach vector is in the same direction as the intended trajectory, an
error is generated

(“37111 tool collinear with weave trajectory”).

pr-0-0-gpr_09.fm
08/1012 131
Motion with Weaving (optional feature)

Fig. 10.5 - Weave Plane

1 - Torch plane 2 - Path 3 - Weaving plane angle 4 - Approach vector (along Z Tool)
5 - Weaving plane 6 - Zero plane 7 - Weaving plane angle 8 - Zero plane
9 - Weaving plane 10- Approach vector (along Z Tool)

The weave plane is established by rotating from the zero plane about the trajectory
tangent by the rotation angle specified in $WEAVE_TBL[n].WV_PLANE. A positive
angle is clockwise, looking at the trajectory direction. Fig. 10.5 shows such a procedure.
Weaving can be executed between two trajectories connected in fly; in this case, the
direction of weaving on the second trajectory is recalculated maintaining the angle of
inclination in relation to the plane of the two trajectories. Weaving will change from one
direction to another without interruption. This capability promotes very simple
programming of complex paths. The angle must be assigned only at the start of the first
movement with weaving and the control will automatically calculate the direction of
subsequent movements, Note that, on the second trajectory, the angle between the
plane of the torch and the direction of weaving will no longer be equal to the angle
indicated in $WEAVE_TBL[n].WV_PLANE; the control will refer to this angle only for the
first movement with weaving.

Fig. 10.6 - Weaving with fly

1 - Start point 2 - Weaving plane angle= 0°

The trajectory weaving connected in fly can be improved in some cases by using the
FLY_CART mode. The weaving direction continuously evolves during fly, without being
interrupted when passing from one motion segment to another. (par. 5.10.2.2
FLY_CART (Controller Aided Resolved Trajectory) on page 72) section for futher

pr-0-0-gpr_09.fm
132 08/1012
Motion with Weaving (optional feature)

details.
For a circular motion, the weave plane is continuously evaluated relative to the path, so
that the weave direction is always perpendicular to the path. If the weave plane is not
parallel to the plane of the circle, the weave plane will be on the frustum of a cone as
shown in Fig. 10.7 - Circular Weaving.

Fig. 10.7 - Circular Weaving

1 - Initial weaving direction 2 - Start point 3 - Final weaving direction


4 - Final point 5 - Centre of circumference

10.3.3 Weave Amplification


Weave amplification permits weaving to be performed on V-grooves or flat butt welds
where the gap between parts varies from beginning to end because of imperfect
alignment.
The weave amplification factor in $WEAVE_TBL[n].WV_AMP_PER is used to grow or
shrink the weave amplitude linearly along the motion. The start of the move is
considered 100%. The value from $WEAVE_TBL determines the percentage at the end
of the move.
If a series of moves is issued in fly or a path is executed, the amplitude corresponding
to 100% is determined at the first move with weaving. Then at the beginning of every
succeeding move, the percentage starts the same as the end of the previous move, and
$WEAVE_TBL[n].WV_AMP_PER is read to determine the percentage at the end of the
move. Thus, a series of moves can be used to weld a long groove or seam without
stopping, and the amplification will change continuously from the start of the first move
to the end of the last move. (Note that the $WEAVE_TBL[n].WV_AMP_PER variable is
read each move, but the definition of 100% is only determined at the first move with
weaving). Fig. 10.8 illustrates the weave amplification feature.

pr-0-0-gpr_09.fm
08/1012 133
Motion with Weaving (optional feature)

Fig. 10.8 - Weave amp

1 - Final amplitude 2 - Final point 3 - Start point 4 - Initial amplitude

1 - Welded part 2 - First move in fly 3 - Second move in fly


4 - Welding 5 - Fly move node

10.4 Stopping Motions with Weaving


When movement stops at the last position of a move or because an operator has
pressed HOLD, the tool can be far away from the original trajectory because of weaving.
In this case, the C5G Controller will bring the torch to the end position before stopping.
In emergency stop or power failure cases, the arm stops as fast as possible, which could
be far from the original trajectory. When power is restored and pressed, trajectory

pr-0-0-gpr_09.fm
134 08/1012
Motion with Weaving (optional feature)

recovery will occur before the weaving motion resumes.


Fig. 10.9 - Weave stop illustrates these cases.

Fig. 10.9 - Weave stop

1. System in Hold state 2. Stop point 3. Original path


4. Emergency stop or Power failure 5. Path reset 6. Original path

10.5 Programming Weaving


Weaving is done by first assigning weave table values and then activating weaving by
selecting an appropriate index into the table by assigning it to $WEAVE_NUM.
$WEAVE_NUM can also be used in a WITH clause. In that case the $WEAVE_NUM
applies only to the current movement. If $WEAVE_TYPE is changed during fly, the
following error occurs:
“(37158) mismatch in fly $WEAVE_TYPE”
$WV_AMP_PER also can be used in a WITH clause. $WV_AMP_PER is not needed to
be assigned the parent structure name and index ($WEAVE_TBL[n]); the current value
of $WEAVE_NUM will apply.
It is not possible to switch the active weave table during a move or path segment, as the
same table is used for the entire segment or move.
However, the weave shape can be changed during a motion by changing the
parameters values of the active table. This can be done either by using a CONDITION
statement or by changing the $WEAVE_TBL[$WEAVE_NUM] fields directly.
The following table is a summary of the predefined variables for Weaving
(see. Tab. 10.1).

Tab. 10.1 - Predefined variables for Weaving

Nome Tipo Limiti Default WITH


$WEAVE_NUM INTEGER [ 0, 10 ] UNINIT YES
$WEAVE_MODALITY INTEGER [ 0, 4 ] 0 YES
$WV_LENGTH_WAVE INTEGER [ 0, 10000 ] 0 NO
$WEAVE_TYPE INTEGER [ 0, 10 ] UNINIT YES
$WEAVE_TBL ARRAY NO
[$NUM_WEAVES] OF
RECORD

pr-0-0-gpr_09.fm
08/1012 135
Motion with Weaving (optional feature)

Tab. 10.1 - Predefined variables for Weaving (Continued)

Nome Tipo Limiti Default WITH


$WEAVE_TBL[idx].WV_PLANE REAL [-180, +180] 0.0 NO
deg
$WEAVE_TBL[idx].WV_AMP_PER INTEGER [ 0, 1000 ] % 100 % YES
$WEAVE_TBL[idx].WV_RIGHT_AMP REAL [0, 20] mm o 0,0 NO
deg
$WEAVE_TBL[idx].WV_LEFT_AMP REAL [0, 20] mm o 0.0 NO
deg
$WEAVE_TBL[idx].WV_CNTR_DWL (*) INTEGER [0, 10000] mm 0 NO
o ms
$WEAVE_TBL[idx].WV_RIGHT_DWL (*) INTEGER [0, 10000] mm 0 NO
o ms
$WEAVE_TBL[idx].WV_LEFT_DWL (*) INTEGER [0, 10000] mm 0 NO
o ms
$WEAVE_TBL[n].WV_END_DWL INTEGER [0, 10000] mm 0 NO
o ms
$WEAVE_TBL[idx].WV_SMOOTH BOOLEAN FALSE NO
$WEAVE_TBL[n]WV_TRV_SPD REAL 0 NO
$WEAVE_TBL[n]WV_TRV_SPD_PHASE REAL 0 NO
$WEAVE_TBL[n]WV_SPD_PROFILE BOOLEAN FALSE NO
$WEAVE_TBL[idx].WV_AMPLITUDE REAL 0.0 NO
$WEAVE_TBL[idx].WV_RADIUS REAL 0.0 NO
$WEAVE_TBL[idx].WV_PLANE_MODALITY INTEGER [0, 1] 0 NO
$WEAVE_TBL[idx].WV_DIRECTION_ANGLE REAL [-180, +180] 0.0 NO
deg
$NUM_WEAVES INTEGER [ 0, 16 ] 10 NO
(*) If $WEAVE_MODALITY=0, mm If $WEAVE_MODALITY=1, ms

10.6 Weaving without Arm motion


This kind of weaving allows to weld without a programmed Arm motion: the target is to
be able to weave the Arm while the being welded part is moved by another Arm.
This kind of weaving is similar to the previously described one; the differences are
explained in the following sections.

10.6.1 Mode
The weaving without Arm motion mode is activated by means of
$CRNT_DATA[num_arm].WEAVE_TYPE_NOMOT predefined variable which has got
the same functionalities as described in par. 10.1 Weaving Mode on page 126: the only
difference is that such a mode is performed without a motion embedded to the weaving.

10.6.2 Activation
For this functionality too, the activation is performed by means of defining the weave

pr-0-0-gpr_09.fm
136 08/1012
Motion with Weaving (optional feature)

table; it is anyway needed to use the predefined variable

$CRNT_DATA[2].WEAVE_NUM_NOMOT

which specifies that the weaving functionality will be performed without Arm motion.
The weave tables are exactely the same as for the weaving with Arm motion. In such a
way, if in a PDL2 program the user needs to perform both weaving with and without Arm
motion, the same information can be used.

10.6.3 Parameters
The used parameters belong to the same group described in the previous par. 10.3
Weaving Parameters on page 127.
Anyway, there are some features which make a no-sense for this functionality: e.g.
mode 1 cannot be selected which involves a wave shape related to the wavelength,
because the Arm does not move.

10.6.4 Example - Using the weaving without Arm motion


To better understand how this kind of weaving does work and how to use it, an example
is provided: let’s suppose that Arm 2 must execute a weaving operation without motion,
Arm 1 moves the part to be welded, and the required time to perform the welding
operation is 3 seconds. Note that it is needed to know the welding time in order to weld.

a. definition of a suitable weave table (e.g. table 1)

$WEAVE_TBL[1].WV_LEFT_AMP := 5
$WEAVE_TBL[1].WV_RIGHT_AMP := 5
$WEAVE_TBL[1].WV_LEFT_DWL := 0
$WEAVE_TBL[1].WV_CNTR_DWL := 0
$WEAVE_TBL[1].WV_RIGHT_DWL := 0
$WEAVE_TBL[1].WV_SMOOTH := TRUE
$WEAVE_TBL[1].WV_TRV_SPD := 0.035
$WEAVE_TBL[1].WV_PLANE := 0
$WEAVE_TBL[1].WV_AMP_PER := 100

b. setup of the following features:


• the Arm must not weave,
• the Arm must use 0 mode related to the transverse speed,
• the weaving is performed in cartesian (WEAVE_TYPE_NOMOT := 0):

$CRNT_DATA[2].WEAVE_NUM_NOMOT := 0
$CRNT_DATA[2].WEAVE_MODALITY_NOMOT := 0
$CRNT_DATA[2].WEAVE_TYPE_NOMOT := 0

c. speeds definition

$SPD_OPT := SPD_LIN
$LIN_SPD := 0.050000001

d. Arm motion, to go to the position where Arm 2 is supposed to weld

pr-0-0-gpr_09.fm
08/1012 137
Motion with Weaving (optional feature)

MOVE LINEAR TO p1

e. weave on p1 position, for the required time (3 s).

$CRNT_DATA[2].WEAVE_NUM_NOMOT := 1
DELAY 3000
$CRNT_DATA[2].WEAVE_NUM_NOMOT := 0

The statement $CRNT_DATA[2].WEAVE_NUM_NOMOT := 0


disables weaving after 3 seconds, in order to allow the Arm to continue its usual
working motions.

WARNING - in case of HOLD state, weaving is stopped and deactivated: enable the
functionality again to move weaving again.

10.7 Weaving on multiarm systems


In order to allow programming with different wave shapes, on Arms sharing the same
program in a multiarm system, $WEAVE_NUM, $WEAVE_MODALITY and
$WEAVE_TYPE are now fields of the $PROG_ARM_DATA[narm] variable.
This means such variables are local to both the program (like it already was, for previous
versions), and the Arm.
Where and when there is not any ambiguity, the $PROG_ARM_DATA[narm] string can
be skipped over.
Such a modification does not cause any incompatibility for single Arm systems.
For multiarm systems the following settings can be made, for example:
– $WEAVE_NUM := 1 -- modally sets the weaving table number, for the program
default Arm;
– $PROG_ARM_DATA[2].WEAVE_NUM := 2 -- modally sets the weaving table
number for Arm 2;
– MOVE TO p1 WITH $WEAVE_NUM=3 SYNCMOVE ARM[2] TO p2 WITH
$WEAVE_NUM = 4 -- nodally sets different weaving tables for the two involved
Arms.

WARNING - There could be a conflict with the previous versions: if the following
statements have been written
– $WEAVE_NUM := 1
– MOVE TO p1 -- it is the default Arm, so weaving is activated
– $WEAVE_NUM := 2
– MOVE ARM[2] TO p2 -- in current version, ARM 2 does not weave because
-- $WEAVE_NUM is set for the $PROG_ARM i.e. ARM 1.

pr-0-0-gpr_09.fm
138 08/1012
Path Governor (optional feature)

11. PATH GOVERNOR (OPTIONAL FEATURE)

Path Governor
The option code is CR17926211.

This function has to be used when MAXIMUM ACCURACY is the priority.


If instead the priority is to obtain robot MAXIMUM SPEED, it is necessary to use the
SmartMove (optional feature).

11.1 Introduction
The Path Governor is a software option to obtain very accurate Cartesian, circular
and/or linear moves, reducing the path error.
It can be applied to any type of machine since it is based on the ACTUAL behaviour of
the robot. It can be executed for all the MOVE instructions, or if preferred only for some
of them.

Important note: greater path accuracy is obtained accepting lower performance


regarding speed, since the enabling of the Path Governor increases the cycle time, if
$PGOV_MAX_SPD_REDUCTION is not zero.
Therefore, according to the application to be executed, the user will have to find the
compromise between reduction in Cartesian speed and increase in cycle time.

– Enable Path Governor


– Disable Path Governor

11.2 Enable Path Governor


The user can enable the use of the Path Governor algorithm by a simple PDL2
assignment:
$SPD_OPT:=SPD_PGOV

The Path Governor cannot be enabled when in Programming mode.

Having enabled the Path Governor, the user has to set the following predefined
variables :
– $LIN_SPD - maximum speed value to execute the path
– 3 predefined variables that indicate the precision:
• $PGOV_ACCURACY - maximum Cartesian error (in mm) allowed during the
execution of the required Cartesian path (with a tolerance of approx. ±0.5mm)

hs-0-0-mot_05.fm
08/1012 139
Path Governor (optional feature)

• $PGOV_ORNT_PER - indicates the geometry error percentage to be taken


into consideration in the execution of the path. This value can be first set at
0%, then later, if the geometry error is still high, it can be increased
• $PGOV_MAX_SPD_REDUCTION - the accepted Cartesian speed reduction
percentage to obtain the required path precision (limits: 0..95).
These predefined variables can be set once for all at the beginning of the motion
program, or also from outside, or they can have different values for each Cartesian
MOVE.
The $PGOV_MAX_SPD_REDUCTION predefined variable is the variable that can have
enormous influence on whether or not the required precision is obtained. In fact, setting
a zero valve will not give any improvement in the path execution in relation to the same
move with the Path Governor disabled.
Furthermore, if the allowed speed reduction is not found adequate for the precision
required in $PGOV_ACCURACY, a Cartesian speed value will be seen that is referred
to a value equal to:

and, as a consequence, the error in the path could be greater than that required.
It is to be noted that, with the Path Governor enabled, the target speed profile will not be
trapezoidal, except in cases of saturation, but will have a speed trend that very similar
to the example shown in Fig. 11.1, where the result obtained during a Cartesian MOVE
is compared with the Path Governor Enabled and Disabled.

Fig. 11.1 - Cartesian Speed profile with Path Governor enabled/disabled

hs-0-0-mot_05.fm
140 08/1012
Path Governor (optional feature)

As can be seen in Fig. 11.1, with the Path Governor, the maximum speed value set is
not necessarily reached, but there is a speed modulation during the motion according to
the Cartesian error that is taking place.

11.3 Disable Path Governor


There are two ways the user can disable the Path Governor:
– Assign a value that is not SPD_PGOV to the predefined variable $SPD_OPT, or
– Assign a zero (0) value to the predefined variable
$PGOV_MAX_SPD_REDUCTION.

hs-0-0-mot_05.fm
08/1012 141
SmartMove (optional feature)

12. SMARTMOVE (OPTIONAL FEATURE)

SmartMove
The option code is CR17926210.

This function has to be used when robot MINIMUM CYCLE TIME is the priority.
If instead the priority is to obtain robot MAXIMUM ACCURACY, it is necessary to use
the Path Governor (optional feature)

– Description
– Jerk Limitation
– Cartesian Motions

12.1 Description
It is an algorithm that can be enabled as a software option to optimise the execution
time of joint AND/OR CARTESIAN motionS. When SmartMove functionality is active,
all joint motions are automatically executed using such an algorithm. As far as executing
Cartesian motions, please refer to par. 12.3 Cartesian Motions on page 143.
By means of the robot dynamic model on all 6 axes, through which the inertia, frictions,
centrifugal and coriolis torques can be determined according to the robot posture and
the load conveyed, the robot motion is planned in the joints space fully exploiting the
torque and speed characteristics made available by the actuators that handle the joints,
so as to have at least one axis with maximum torque.
To optimise the results of the algorithm and avoid excessive torque requirements on
axes in motion, it is fundamental to declare the load data correctly, possibly using the
Payload identification (optional function) procedure.
The tolerance between the current predicted by the dynamic model and the actual
current of each individual axis can be configured through the system variables
$ARM_DATA[num_arm].SM4_SAT_SCALE[num_axis].

It is recommended to reduce such tolerances, because they are directly related to


the stress passed by the reducers.

Fig. 12.1 shows a comparison between two speed profiles, without and with the
SmartMove algorithm.

hs-0-0-mot_06.fm
142 08/1012
SmartMove (optional feature)

Fig. 12.1 - SmartMove - Comparison

Spd - Speed
Tr - Time reduction

12.2 Jerk Limitation


It is an algorithm to limit the dynamic over-stress, avoiding moves, especially short
moves, with acceleration variations that limit the joints oscillation.
The Jerk limitation is incorporated in SmartMove and automatically manages the Jerk
value to be used for each move.
However, if, for the particular application to be executed, the moves cause too much
stress, or on the contrary a reduction of the cycle time is preferred, to the detriment of
the stress, it is possible to ask COMAU to change the Jerk limitations to suit the specific
requirements.

12.3 Cartesian Motions


Unlike joint motions (MOVE JOINT), to perform cartesian motions (either LINEAR or
CIRCULAR) it is needed to set the following $SPD_OPT value:

$SPD_OPT := SPD_SM4C

SmartMove algorithm will automatically calculate the maximum TCP acceleration and
speed values, depending on the specified payload, on the operating zone and on the
axes configuration.

hs-0-0-mot_06.fm
08/1012 143
Joint Soft Servo (optional feature)

13. JOINT SOFT SERVO (OPTIONAL FEATURE)

Joint Soft Servo


The option code is CR17926203.

13.1 Description
Joint Soft Servo is a software option used in some applications when it is required that
the robot is compliant to movements produced by external forces. For example, when a
workpiece is hooked from a press, the detachment is facilitated by the pushing of a roll;
the robot must follow the movement without opposition.
When Joint Soft Servo is enabled, the robot should be steady. The Joint Soft Servo
modality is automatically disabled by a DRIVE OFF.
The degree of compliance of each axis must be defined when such a modality is
enabled.
To enable/disable the Joint Soft Servo modality, use ARM_SOFT built-in routine,
provided by PDL2 programming language.

For further information, please refer to PDL2 programming language manual - BUILT-IN
routines List chapter, ARM_SOFT paragraph.

hs-0-0-mot_09.fm
144 10/0713
Flow Modulate Algorithm

14. FLOW MODULATE


ALGORITHM
This service, used in applications such as Cosmetic Sealing and Glueing, modulates the
flow of the material to be delivered during the part machining, according to the speed of
the TCP (Tool Center Point).
The delivery device, according to the voltage set, delivers a certain material.
The material dispensing machine defines the maximum voltage value it can handle.
The voltage to be delivered is passed from the C5G each time by a predefined either
$FMO or $AOUT variable. Maximum allowed value is 65535.
If, for example, the maximum voltage value that can be delivered is 10 Volt and the
either $FMO or $AOUT predefined variable is set at 65535 (maximum $FMO / $AOUT
value), this means that the machine will apply the maximum voltage (10 Volt) for the
material delivery.
Certain parameters have to be set to define the modulation functioning.
These parameters are kept in the predefined variable $FLOW_TBL (2 elements array);
the values are set by the motion parameters, with the following fields:
– $FW_ARM (integer): arm to which this algorithm is applied.
– $FW_AXIS (integer): axis to which this algorithm is applied: only to be specified
when $FW_VAR is set at 2.
– $FW_CNVRSN (real): conversion factor to be applied to calculate the flow to be
delivered.
– This conversion value can be modified during the algorithm operation.
– $FW_VAR (integer): INTEGER. Type of variable to be operated on. If set at 1 the
flow modulation algorithm is applied to $ARM_VEL /cosmetic sealing); if set at 2
the flow modulation algorithm is applied to $RAD_VEL (glueing).
– $FW_SPD_LIM (2 real array): indicates the minimum and maximum speed limits
over which the flow modulation algorithm will apply the nearest limit.
– $FW_FLOW_LIM (2 integer array): indicates the minimum and maximum flow
limits over which the modulation algorithm will apply the nearest limit.
– $FW_ENBL (boolean): algorithm state indicator - enabled or disabled.
– $FW_START (boolean): indicates the time interval (in milliseconds) between the
speed sample acquisition (immediately following the call to FLOW_MOD_ON) and
the data writing on the analog port indicated in the call to FLOW_MOD_ON.
The formula that determines the conversion factor calculation is based on the maximum
speed that is intended to be used for the robot and the maximum applicable voltage in
bits. These values are defined during the initial configuration when setting the
$FLOW_TBL fields.

pr-0-0-gpr_12.fm
02/0610 145
Flow Modulate Algorithm

Example:

The voltage, in bits, is determined by the formula:

The voltage value is read by the machine that delivers the material on an integer port,
usually either a $FMO or $AOUT port, defined during the algorithm enabling; to enable
the algorithm, the FLOW_MOD_ON built-in routine is used, with the call:
FLOW_MOD_ON (<analog_port>, <flow_table_index>)
where:
– <port> is to be INTEGER type. For example: either $FMO or $AOUT.
– <flow_table_index> where the type of INTEGER is the $FLOW_TBL index.
Possible values: 1 or 2.
Obviously there is also a built-in routine for disabling, its call is:
– FLOW_MOD_OFF (<flow_table_index>)
– <flow_table_index> INTEGER. The $FLOW_TBL index. Possible values: 1 or 2.
The program that calls the FLOW_MOD_ON on a certain index must be the same as
that which calls FLOW_MOD_OFF on that index.
When the program is deactivated the table is automatically released (implicit
FLOW_MOD_OFF).

Fig. 14.1 - Delivery voltage

1. Delivery flow
2. Conversion factor
y Voltage (V) to be delivered by the dispensing machine (written in the analog port passed to
FLOW_MOD_ON)
x TCP speed ($ARM_VEL or $RAD_VEL)

pr-0-0-gpr_12.fm
146 02/0610
Presuppositions for SMART Robot programming

15. PRESUPPOSITIONS FOR SMART ROBOT


PROGRAMMING

15.1 Introduction
Current chapter summarizes further information related to the use of COMAU robots.
They are classified as being with spherical wrist or with non-spherical wrist.
COMAU robots which are involved in current chapter are shown in the following
Tab. 15.1 - Involved Robot models:

Tab. 15.1 - Involved Robot models

Robot Spherical wrist Non-spherical wrist


SMART NJ1 X
SMART NJ2 X
SMART NJ3 X
SMART NJ4 X
SMART NS X
SMART NM X X

The following topics are fully described:


– Glossary
– Offset algorithm with Dynamic Model
– Kinematic offset algorithm (optional feature)
– Moving through axis 5 singularities
– Robots without compensation (effect of the inverse kinematics)
– Programming rules for non-spherical wrist robots (SMART NJ4)
The list of error messages is reported and the meaning is explained. Some notes are
also given about mapping between C5G error messages and RRS (Robot Realistic
Simulation) ones that are sent by Robcad while simulating a program. This is useful
because RRS specification doesn't include messages enough to describe all the
expected situations.

pr-0-0-gpr_05.fm
03/0111 147
Presuppositions for SMART Robot programming

15.2 Glossary
TCP - Tool Center Point. It is the point at the end of the tool and it is geometrically
described by the $TOOL system variable or by the Tool tables in DATA environment. It
can be local or remote. For SMART NJ4(L) robot the TCP position, with reference to the
robot axes, causes some limitations to the robot working area.
WCP - Wrist Center Point. For spherical wrist robots, WCP is the intersection point
between joint 5 and joint 6; for SMART NJ4 robots (non-spherical wrist) there isn’t a true
WCP: such a word means the intersection point between joint 4 and joint 5.

1. Wrist offset

RRS - Robot Realistic Simulation. It is a protocol that defines some rules to implement
a software sequence that allows a robotics CAD simulator (i.e. Robcad) to move the
robot using the same algorithms than the original Controllers. Such a software sequence
is called RCS module. It is provided by Comau and integrated into the simulators.
Nominal position - This term refers to machines with the Kinematics compensation
algorithm. The nominal position is the destination where the robot must move its TCP.
It usually comes from a CAD simulation where the model of the robot is theoretical,
without mechanical strains due to payload, calibration errors, etc.
Internal representation of the robot position - This term refers to machines with the
Kinematics compensation algorithm. The internal representation of the robot position is
the one coming out from the encoders/resolvers. It is also the position where the robot
is really moved to compensate the differences between the real machine and the
theoretical robot model.
Cartesian position or POSITION - It is a variable that describes the target position for
a MOVE statement by referring to a Cartesian frame of reference. In C5G each
POSITION has three components for the location (X, Y, Z), three angles for the
orientation and a configuration string.
Joint position or JOINTPOS - It is a variable that describes the target position for a
MOVE statement by reporting the value of each robot axis.

pr-0-0-gpr_05.fm
148 03/0111
Presuppositions for SMART Robot programming

15.3 Offset algorithm with Dynamic Model


This algorithm improves the mechanical precision in movement and positioning, thus
cutting down the cycle time.
The algorithm functions continually, both during robot movement and during stops,
regardless of the type of trajectory or the duration of the pause: the only condition is that
the arm be in DRIVE ON.
The modelling of the robot dynamic characteristics requires an accurate definition of the
tool that is mounted on the flange.
The description of the tool can be executed by means of three system variables that
are added to $TOOL. These are $TOOL_MASS, that is the tool mass, $TOOL_CNTR,
which is the centre of the tool mass and $TOOL_INERTIA.
It must be noted that accuracy in the assignment of the tool characteristics has a strong
influence on the machine performance.
Furthermore, if the robot is used to transfer components, it is important that the
declaration of the dynamic characteristics includes the contribution of the workpiece
mass, as well as that of the gripping tool; this also applies for the definition of the mass
centre coordinates.

15.4 Kinematic offset algorithm (optional feature)


This algorithm improves the precision of the robot positioning in the work area.
The software offsets the kinematic errors, caused by the imprecision of the robot lever
lengths or the incorrect coupling of the axes (axis orthogonality ), and deflection error
caused by the weight of the mechanical parts.
To make it operational, it is necessary to identify the actual kinematic model of each
individual robot so as to obtain a machine offset file.

15.5 Moving through axis 5 singularities


In current paragraph information are given about the following topics:
– Using WRIST_JNT modality to go through singularities
– Manual motion (jog keys)

15.5.1 Using WRIST_JNT modality to go through singularities


In all the robot mechanical structures there are particular positions where performances
are reduced; such positions are called singularities. Usually, when robot gets close to a
singularity while moving in a linear/circular way, either the speed is reduced or the
trajectory is changed as to the espected one. This is true for every robot regardless the
manufacturer.
Anthropomorphic robots, like the ones in Tab. 15.1 - Involved Robot models, have three
singularities. The most evident one happens when axis 5 is at zero degrees. When this
occurs, axis 4 is aligned with axis 6. This produces different behaviors depending on the

pr-0-0-gpr_05.fm
03/0111 149
Presuppositions for SMART Robot programming

shape of the wrist. Further information are described in the following par. 15.6.1.4 Axis
5 singularity on page 154 for non-spherical wrist robots and par. 15.6.2.1 Axis 5
singularity on page 160 for spherical wrist robots.
Nevertheless there is a general feature available with Comau C5G Robot Controller that
allows the robot to achieve high performances while moving through axis 5 singularity
(wrist singularity).
It is possible to enable this type of evolution by setting the $ORNT_TYPE system
variable to the WRIST_JNT value ($ORNT_TYPE:=WRIST_JNT). It is advisable to
enable this modality only with moves that have to go through the singularity because
the default evolution modality, RS_WORLD, generally achieves the best behavior from
the application point of view. The RS_WORLD modality allows either maintaining
constant orientation, if necessary, or changing it by keeping the tool on a plane.

1. Side view 2. Front view

Nevertheless the RS_WORLD evolution doesn't allow the robot always to move through
the singularity zone. In this cases the WRIST_JNT modality performs the best behavior.
The effect is that the speed is maintained at a high value while the orientation of the tool
slightly looses the plane.
The evolution can also be very big if the starting and ending point are very far from the
singularity zone. This can happen because the WRIST_JNT evolution implements an
algorithm that maintains the TCP exactly on the Cartesian path while the wrist axes are
moved from the initial to the final position in joint evolution.
The effect of WRIST_JNT modality is generally good from the application point of view.
In some particular cases it would be necessary to follow additional programming rules
explained later in this document (see par. 15.7 Programming rules for non-spherical
wrist robots (SMART NJ4) on page 160).
The only limitation referring to the WRIST_JNT is that it is not allowed to continuously
move (MOVEFLY TO ...) between two movements with different evolution type. So if a
move has the standard RS_WORLD evolution and the next is WRIST_JNT, either the
fly must be removed or the evolution type of the first one must be set to WRIST_JNT too.

pr-0-0-gpr_05.fm
150 03/0111
Presuppositions for SMART Robot programming

1 - Linear trajectories while getting near the singularity.

The curved lines are the flange trajectories, while the TCP moves along the right path
2 - Exact singularity position 3 - Behaviour of the WRIST_JOINT modality.

Getting closer to the singularity, speed is maintained high while orientation slightly changes

15.5.1.1 Using WRIST_JNT modality to go through singularities


As already explained, the use of WRIST_JNT evolution modality is the right method to
solve all singularity problems. This method is useful mainly for moving through the
singularity zone because it allows axis 5 to reach the zero position while TCP is following
the required Cartesian trajectory.
Here follows an example involving SMART NJ4 model. With WRIST_JNT modality it is
possible to perform vertical trajectories around the singularity point. Of course, all the
positions must be out of the singularity zone (see par. 15.6.1.4 Axis 5 singularity on
page 154) but any trajectory can cross it.
If the program is correctly designed, axis 5 is asked to move from a negative to a positive
value (or vice-versa) while the wrist offset is always maintained on the same side. As
already explained, the orientation is slightly changed during the movement. This is
automatically done by the system without any need of modifying points.

1 - Level of the singularity point

pr-0-0-gpr_05.fm
03/0111 151
Presuppositions for SMART Robot programming

The following picture shows an example of the maximum angular error that is applied
to the orientation while entering different circular zones around the singularity point.
These data has been computed with a tool exactly aligned with axis 6. Many vertical
trajectories have been executed around the calibration position of the SMART NJ4
model, properly programming the points and moving in WRIST_JNT evolution method
through the singularity zone.

1 - Singularity exact position

15.5.2 Manual motion (jog keys)


Also during the jogging phase (manual movement of the robot) it is possible to avoid all
problems due to axis 5 singularity by using the WRIST_JNT evolution.
There are 4 standard modalities for jogging:
– TOOL
– UFRAME
– BASE
– JOINT
The first three ones are for Cartesian movements, with reference to tool frame, user
frame and world frame; the last one allows moving each single robot joint. These
modalities are usually the best from the application point of view but they do not allow
robot to move in a Cartesian way when axis 5 is inside the singularity zone. To achieve
this task it is necessary to enable the WRIST_JNT modalities for jogging.
The WRIST_JNT evolution can be set for Cartesian manual, from the Motion page,
Basic sub-page, COORD field of the Teach Pendant. On theTeach Pendant status bar
the following words will be seen: Wr-Base, Wr-Tool, Wr-Ufrm, Joint.
WRIST_JNT modalities allow TCP to move along a straight line without moving wrist
axes, by pressing the first three jog buttons: +1X/-1X, +2Y/-2Y, +3Z/-3Z. On the other
hand, pressing jog buttons +4/-4, +5/-5, or +6/-6, it is possible to move a single wrist axis
while maintaining TCP steady. These modalities are useful to go through the singularity
because they allow the robot to be jogged in a Cartesian way also if axis 5 is exactly at
0 degrees.

pr-0-0-gpr_05.fm
152 03/0111
Presuppositions for SMART Robot programming

15.6 Robots without compensation (effect of the


inverse kinematics)
In current paragraph, information are given about the following topics:
– Inverse conversion of SMART NJ4 (non-spherical wrist) model
– Inverse conversion of SMART NJ models (spherical wrist only)

15.6.1 Inverse conversion of SMART NJ4 (non-spherical wrist)


model
SMART NJ4(L) robot has a particular hollow wrist with an offset between axis 4 and 6.
To compute the value of the axes that allows the robot moving to a specific Cartesian
position (inverse kinematics conversion), it is necessary to run an iterative algorithm that
uses the WCP position and the TCP position of the robot, with reference to its base.
In the following sections the related effects are shown:
– Approximation in the orientation
– Move to a taught POSITION
– Fly between MOVE LINEAR/CIRCULAR and MOVE JOINT
– Axis 5 singularity
– Cartesian position out of range
– TCP in the back of the robot
– TCP behind axis 2
– WCP close to axis 1

15.6.1.1 Approximation in the orientation


The Cartesian position reached by the TCP is always correct in X, Y and Z. This means
that the X, Y and Z coordinates of the final position correspond to the taught one (unless
some effect due to compensation). On the other hand, the orientation can be
approximated. This means that the robot reaches the final position with the Euler angles
slightly different to the original ones. This difference is usually less than 0.8 degrees (can
be bigger in proximity of the border of the working area).
This approximation affects all the axes and can produce some unexpected error
message because some of the axes can get closer to some limit than the taught joints.
For this reason some bigger ranges are advised in the following paragraphs. These
ranges are called safe ranges.
The approximation does not affect the locations recorded as JOINTPOS.

15.6.1.2 Move to a taught POSITION


The approximation in the orientation can produce the following effect. When a MOVE is
executed to a Cartesian position, the flange (not the TCP) can move a few millimetres
around its position. The displacement is usually less that 10 millimeters with a tool 1500
millimeters long.

pr-0-0-gpr_05.fm
03/0111 153
Presuppositions for SMART Robot programming

1a - 1b: difference between the two flange positions, due to the orientation approximation
2a - 2b: orientation approximation

15.6.1.3 Fly between MOVE LINEAR/CIRCULAR and MOVE JOINT


The approximation in the orientation causes a small difference between the computed
joint values (to finish current movement) and the real values.
For this reason it is advisable not to use a fly between a linear/circular move and a joint
move or vice-versa.

15.6.1.4 Axis 5 singularity


Due to the hollow wrist the singularity zone for SMART NJ4(L) robot is wider than the
position at 0 degrees of axis 5. The conversion can give back a solution only if axis 5 is
out of range ±6° around zero value and multiple of 180°. If, during the conversion, axis
5 enters this zone an error message is issued.
Due to the approximation in orientation, the error message can come out also on a
POSITION that had been taught with axis 5 slightly out of ±6° threshold . Since the
approximation is usually less than 0,8°, a safe range is ±7°.

[ -6; +6 ]
Forbidden ranges [ -174; -186 ]
[ +174; +186 ]
[ -7; +7 ]
Safe ranges [ -173; -187 ]
[ +173; +187 ]

pr-0-0-gpr_05.fm
154 03/0111
Presuppositions for SMART Robot programming

Fig. 15.1 - SMART NJ4 forbidden zone

1. ±6 degrees around 0° and 180°


Actions Allowed Forbidden Notes
REC JOINTPOS inside the singularity zone It is possible to record a joint
X
position (JOINTPOS).
REC POSITION/XTNDPOS inside the It is NOT possible to record a
singularity zone X Cartesian position (POSITION or
XTNDPOS).
MOVE JOINT through singularity zone X
MOVE LINEAR/CIRCULAR through It is possible to move in a
singularity zone with the standard evolution X Cartesian way only with the
modality (RS_WORLD) WRIST_JNT evolution (see
MOVE LINEAR/CIRCULAR through par. 15.5 Moving through axis 5
singularity zone with the WRIST_JNT singularities on page 149). In the
evolution modality X standard modality (RS_WORLD)
MOVE LINEAR/CIRCULAR is
not allowed.
JOG JOINT inside the singularity zone X It is possible to jog the robot in a
Cartesian way only if the
JOG BASE, UFRM, TOOL inside the
X WRIST_JNT modalities are
singularity zone
enabled (WR-BASE, WR-UFRM,
JOG WR-BASE, WR-UFRM, WR-TOOL inside WR-TOO, see par. 15.5.2
the singularity zone Manual motion (jog keys) on
X page 152). It is not allowed to jog
inside the singularity zone with
the standard jog modalities
(BASE, UFRAME, TOOL).
MOVE JOINT TO JOINTPOS inside the
X
singularity zone
MOVE LINEAR TO JOINTPOS inside the
X If the destination point is inside
singularity zone
the singularity zone it is not
MOVE JOINT TO POSITION/XTNDPOS inside
X possible to move there both with
the singularity zone
the standard evolution and with
MOVE LINEAR TO POSITION/XTNDPOS WRIST_JNT.
X
inside the singularity zone

pr-0-0-gpr_05.fm
03/0111 155
Presuppositions for SMART Robot programming

Error messages
– 36996 (0x9084) "Wrist axis at undefined position" before starting the move.
– 62479 (0xf40f) "Wrist axis at undefined position" while moving into the forbidden
zone.
– 40014 (0x9c4e) "Wrist axis at undefined position" while teaching/modifying a point.
– RCS MODULE - Status returned: -59 "The specified position is singular".

15.6.1.5 Cartesian position out of range


Due to the particular wrist of SMART NJ4(L) model, the external boundary of the
Cartesian working area is slightly reduced with respect to spherical-wrist machines.
This reduction depends on the direction of the wrist offset:
– If the wrist offset is downward there is no limitation.
– If the wrist offset is upward there is an additional forbidden area for SMART NJ4(L)
robot. The width of this area is 180 mm in the front area and 225 mm in the rear
area. For SMART NJ4(L) robots, the width is 140 mm in the front area and 215 mm
in the rear area.

These areas can be reached in a joint way; the limitations only refer to Cartesian
movements

Actions Allowed Forbidden Notes


REC JOINTPOS inside the forbidden zone It is possible to record a joint
X
position (JOINTPOS).
REC POSITION/XTNDPOS inside the It is NOT possible to record a
forbidden zone X Cartesian position (POSITION or
XTNDPOS).
MOVE JOINT through the forbidden zone X It is allowed to move through this
MOVE LINEAR/CIRCULAR through the zone with every type of
forbidden zone movement. It is sufficient that the
X destination point is out of the
forbidden zone.
JOG JNT inside the forbidden zone X
JOG BAS, USR, TOL inside the forbidden It is possible to jog the robot in
X
zone
every modality.
JOG BWR, UWR, TWR inside the forbidden
X
zone
MOVE JOINT TO JOINTPOS inside the
X
forbidden zone
MOVE LINEAR TO JOINTPOS inside the If the destination point is inside
X
forbidden zone the forbidden zone, it is possible
MOVE JOINT TO POSITION/XTNDPOS inside to reach it only if it is a
X JOINTPOS.
the forbidden zone
MOVE LINEAR TO POSITION/XTNDPOS
X
inside the forbidden zone

pr-0-0-gpr_05.fm
156 03/0111
Presuppositions for SMART Robot programming

Error messages
– 36994 (0x9082) "Pos out of range" before starting the move.
– 62477 (0xf40d) "Cartesian position out of range" while moving into the forbidden
zone.
– 40012 (0x9c4c) "Pos out of range" while teaching/modifying a point.
– RCS MODULE - Status returned: -52 "Cartesian position is out of work
range".

15.6.1.6 TCP in the back of the robot


There are some limitations in the working area that are not immediately visible to the
user. They depend on the position of the TCP with respect to the robot axes. For this
reason they are related to the current dimension of the tool (both remote and local).
There is a forbidden zone when the TCP tries to go in the back of the robot with respect
to axis 1. The width of this area is approximately 150 mm on both sides.
Approaching this area the approximation on the orientation increases up to some
degrees.

The same situation can also happen with remote tool.

1 - Remote TCP inside the forbidden zone

pr-0-0-gpr_05.fm
03/0111 157
Presuppositions for SMART Robot programming

Actions Allowed Forbidden Notes


REC JOINTPOS inside the forbidden zone It is possible to record a joint
X
position (JOINTPOS).
REC POSITION/XTNDPOS inside the It is NOT possible to record a
forbidden zone X Cartesian position (POSITION or
XTNDPOS).
MOVE JOINT through forbidden zone X
MOVE LINEAR/CIRCULAR through forbidden It is possible to move in a
zone with the standard evolution modality X Cartesian way only with the
(RS_WORLD) WRIST_JNT evolution (see
MOVE LINEAR/CIRCULAR through forbidden par. 15.5 Moving through axis 5
zone with the WRIST_JNT evolution modality singularities on page 149). In the
X standard modality (RS_WORLD)
MOVE LINEAR/CIRCULAR is
not allowed.
JOG JNT inside the forbidden zone X It is possible to jog the robot in a
Cartesian way only if the
JOG BAS, USR, TOL inside the forbidden
X WRIST_JNT modalities are
zone
enabled (BWR, UWR, TWR, see
JOG BWR, UWR, TWR inside the forbidden par. 15.5.2 Manual motion (jog
zone keys) on page 152). It is not
X allowed to jog inside the
forbidden zone with the standard
jog modalities (BAS, USR, TOL).
MOVE JOINT TO JOINTPOS inside the
X
forbidden zone
MOVE LINEAR TO JOINTPOS inside the If the destination point is inside
X
forbidden zone the forbidden zone, it is possible
MOVE JOINT TO POSITION/XTNDPOS inside to reach it only if it is a
X JOINTPOS.
the forbidden zone
MOVE LINEAR TO POSITION/XTNDPOS
X
inside the forbidden zone

Error messages
– 36995 (0x9083) "Axis 1 at undefined position" before starting the move.
– 62478 (0xf40e) "Axis 1 at undefined position" while moving into the forbidden zone.
– 40013 (0x9c4d) "Axis 1 at undefined position" while teaching/modifying a point.
– RCS MODULE - Status returned: -52 "Cartesian position is out of work
range".

15.6.1.7 TCP behind axis 2


There is a forbidden zone when the TCP tries to go behind a plane containing axis 2.
The width of this area is approximately 150 mm on both sides. Approaching this area
the approximation on the orientation increases up to some degrees.
This same situation can happen also with remote tool ($TOOL_RMT:=TRUE or nodal
move with rtf(i,j)).

pr-0-0-gpr_05.fm
158 03/0111
Presuppositions for SMART Robot programming

1. TCP inside the forbidden zone 2. remote TCP inside the forbidden zone

Actions Allowed Forbidden Notes


REC JOINTPOS inside the forbidden zone It is possible to record a joint
X
position (JOINTPOS).
REC POSITION/XTNDPOS inside the It is NOT possible to record a
forbidden zone X Cartesian position (POSITION or
XTNDPOS).
MOVE JOINT through forbidden zone X
MOVE LINEAR/CIRCULAR through forbidden It is possible to move in a
zone with the standard evolution modality X Cartesian way only with the
(RS_WORLD) WRIST_JNT evolution (see
MOVE LINEAR/CIRCULAR through forbidden par. 15.5 Moving through axis 5
zone with the WRIST_JNT evolution modality singularities on page 149). In the
X standard modality (RS_WORLD)
MOVE LINEAR/CIRCULAR is
not allowed.
JOG JNT inside the forbidden zone X It is possible to jog the robot in a
Cartesian way only if the
JOG BAS, USR, TOL inside the forbidden
X WRIST_JNT modalities are
zone
enabled (BWR, UWR, TWR, see
JOG BWR, UWR, TWR inside the forbidden par. 15.5.2 Manual motion (jog
zone keys) on page 152). It is not
X allowed to jog inside the
forbidden zone with the standard
jog modalities (BAS, USR, TOL).
MOVE JOINT TO JOINTPOS inside the
X
forbidden zone
MOVE LINEAR TO JOINTPOS inside the If the destination point is inside
X the forbidden zone, it is possible
forbidden zone
to reach it only if it is a
MOVE JOINT TO POSITION/XTNDPOS inside JOINTPOS
X
the forbidden zone
MOVE LINEAR TO POSITION/XTNDPOS
X
inside the forbidden zone

pr-0-0-gpr_05.fm
03/0111 159
Presuppositions for SMART Robot programming

Error messages
– 36994 (0x9082) "Pos out of range" before starting the move.
– 62477 (0xf40d) "Cartesian position out of range" while moving into the forbidden
zone.
– 40012 (0x9c4c) "Pos out of range" while teaching/modifying a point.
– RCS MODULE - Status returned: -52 "Cartesian position is out of work
range".

15.6.1.8 WCP close to axis 1


There is a forbidden zone when the WCP tries to enter a cylinder around axis 1. The
radius of the cylinder is approximately 200 mm.

Error messages
– 36995 (0x9083) "Axis 1 at undefined position" before starting the move.
– 62478 (0xf40e) "Axis 1 at undefined position" while moving into the forbidden zone.
– 40013 (0x9c4d) "Axis 1 at undefined position" while teaching/modifying a point.
– RCS MODULE - Status returned: -52 "Cartesian position out of work range".

15.6.2 Inverse conversion of SMART NJ models (spherical wrist


only)
SMART NJ robots have spherical wrist and this simplifies the conversion algorithm with
respect to SMART NJ4 robots. The most part of the limitations explained in previous
par. 15.6.1 Inverse conversion of SMART NJ4 (non-spherical wrist) model on page 153
don’t exist for spherical wrist robots. There is only some limitation about the singularity
of axis 5 and when the TCP is close to axis 1 for spherical wrist shelf mounted machines.
Detailed information are given about Axis 5 singularity.

15.6.2.1 Axis 5 singularity


There is not a forbidden zone when axis 5 is close to zero degrees but it is anyway
advisable not to move through the singularity because close to this zone axes 4 and 6
are required to accelerate and move very fast. The speed of the TCP is reduced while
moving in a Cartesian way close to this zone.
The WRIST_JNT modality (see par. 15.5 Moving through axis 5 singularities on
page 149) is a good method to move through the singularity zone when the
accelerations are too high or when the behavior of the robot is not proper for the specific
application.

15.7 Programming rules for non-spherical wrist robots


(SMART NJ4)
In current paragraph, some programming rules are described in order to help the robot
user and the CAD programmer, to properly use COMAU robots (mainly SMART NJ4
models).

pr-0-0-gpr_05.fm
160 03/0111
Presuppositions for SMART Robot programming

Here following, some hints are given about:


– How to stay away from a singularity zone
– Using WRIST_JNT modality to go through singularities

SMART NJ4 robot has been designed for integration of cabling and ease of off-line
programming. For this reason it has a fixed wrist configuration to give the needed space
and distances to include pre-twisted cables and hoses through the wrist. Following this
concept, such a robot model is completely without any external cable on the forearm,
avoiding the unknown behavior of the cables with conventional robots while moving
close to the wrist singularity.

The disadvantage is that SMART NJ4 robot has a larger singularity zone around axis 5
with respect to spherical wrist robots (see par. 15.6.1.4 Axis 5 singularity on page 154).
The following programming rules explain how it is possible to perform application
processes staying away from the singularity zone or moving through it with the
WRIST_JNT feature of the C5G Robot Controller.

15.7.1 How to stay away from a singularity zone


The width of the singularity zone for non-spherical wrist robots (SMART NJ4) is ±6
degrees. As it has been explained in par. 15.5 Moving through axis 5 singularities on
page 149 it is possible to go through this zone also following a Cartesian path, but in
most cases it is possible to stay away from the singularity. There are three methods to
achieve this task:
– Changing the orientation of the points along the path;
– Properly designing the work-cell layout;
– Modifying tool inserting a small angle between robot flange and tool flange.
The same methods are useful to solve problems with points which are very close to the
working area borders.

15.7.1.1 Changing the orientation of the points along the path


In most applications the tool has a shape that allows rotating around the approaching
direction, without reducing the process quality. This is possible with tools that are
symmetric along a direction. The arc-welding torch and the spot-welding gun are typical
examples.

1 - Tool approach vector

In these cases it is always possible to modify the points (typically POSITIONS) only

pr-0-0-gpr_05.fm
03/0111 161
Presuppositions for SMART Robot programming

adding a small rotation around the approach direction. With the real robot this can be
done by jogging in the TOL modality (jogging with reference to the tool frame) and
pressing jog button +6/-6 (rotation around Z axis that is typically the approach vector); if
the position comes from a CAD system or it is directly written in the program, just modify
the third Eulerian angle e3 (POS(x, y, z, e1, e2, e3, ’’)). On the real robot, a small
rotation of 5° up to 10° allows the wrist to go away from the singularity zone.

The rotation takes more effect if the tool approach vector is not parallel to axis 6 of the
robot. If they are parallel, something can still be done, provided that the TCP is not
aligned along axis 6.

The following picture shows three different cases with a spot welding gun.

Fig. 15.2 - BEST situation (90° between axis 6 and gun approach vector)

Fig. 15.3 - WORST situation (approach vector aligned to axis 6)

Fig. 15.4 - MEDIUM situation (approach vector parallel to axis 6, but not
aligned)

1 - Distance between axis 6 and tool approach vector

pr-0-0-gpr_05.fm
162 03/0111
Presuppositions for SMART Robot programming

Note that rotating around the approach vector is not the only way to stay away from the
singularity zone. Any rotation works and never changes the TCP position in x, y, z.
When the application does not strictly force the orientation of the tool, a small change
could considerably improve the wrist position and the robot performances.

15.7.1.2 Properly designing the work-cell layout


There are some cases where the first method (par. 15.7.1.1 Changing the orientation of
the points along the path on page 161) doesn’t apply. This happens, sometimes, with
palletizing applications where the orientation is fixed. In such cases it is necessary to
properly design the work-cell layout, in order to avoid entering the singularity zone. Also
the shape of the tool is very important to solve bad situations and improve the robot
performances (see par. 15.7.1.3 Modifying tool inserting a small angle between robot
flange and tool flange on page 165).
The programmer must avoid situations in which pallets are exactly in front of the robot
and grippers are oriented in the direction of axis 6 (see pictures below).
Such a bad situation comes from the following three conditions:
– the gripper is aligned with axis 6;

– the pallet is placed at the same level of the robot calibration position;
– the pallet is placed exactly in front of the robot.

pr-0-0-gpr_05.fm
03/0111 163
Presuppositions for SMART Robot programming

To eliminate any singularity problems, the programmer has to remove al least one of the
listed above conditions. For example, putting the pallet in a lower position or mounting
the robot in a higher place the robot will be able to reach all the positions on the rack
without any problems (see next picture).

Similarly it is possible to solve any singularity problem by laterally moving the rack. In
this case it is not necessary to change the height.

In any case the best solution can be found by means of an off-line simulation. In this way
it is possible to calculate the minimum displacement of the rack, either sideways, or up,
or down .
It is important to remember that SMART NJ4 models gives big advantages during
simulation because there aren’t any external cable on the forearm. This allows solving
any reachability problem during the work-cell design phase. At this time it will be
possible to choose the best location for the elements, the best gripper shape and robot
paths.

pr-0-0-gpr_05.fm
164 03/0111
Presuppositions for SMART Robot programming

15.7.1.3 Modifying tool inserting a small angle between robot flange and tool
flange
The gripper design is very important to improve the robot capabilities. This is true for all
the robot models. In addition to this, for SMART NJ4 robots the gripper shape can solve
any problem with singularity.
A small angle between the robot flange and the gripper is recommended in order to
considerably improve the reachability of singular positions.

pr-0-0-gpr_05.fm
03/0111 165
Presuppositions for SMART Robot programming

As shown in the above pictures, such a solution allows the robot to follow a linear
trajectory exactly in front of it from up to down. It also allows to reach all the available
working area always maintaining the frontal position and the same orientation.
The same applies to spot-welding guns. If the work-cell layout is already defined, a small
angle can considerably improve the behavior of the robot. This method can also solve
the worst situations where the approach vector of the gun is exactly aligned with axis 6
(see par. 15.7.1.1 Changing the orientation of the points along the path on page 161).
Of course, the use of an off-line simulation simplifies the chose of the angle and allows
an optimization of all the details of the application.

pr-0-0-gpr_05.fm
166 03/0111
Presuppositions for SMART Robot programming

15.7.2 Conclusions
Many methods and hints have been given to increase the capabilities of SMART NJ4

pr-0-0-gpr_05.fm
03/0111 167
Presuppositions for SMART Robot programming

robots inside the singularity zone. It has been demonstrated that in the most cases it is
possible to stay out of this zone, getting the best performances from the robot anyway.
When it is absolutely necessary to go through the singularity, WRIST_JNT modality
allows the robot to move at a very high speed with an angular error that can be accepted
in the most processes. In any case the simulation tools can be effectively used to obtain
the best results from the system.

pr-0-0-gpr_05.fm
168 03/0111
Collision Detection (optional feature)

16. COLLISION DETECTION


(OPTIONAL FEATURE)

Collision Detection
The option code is CR17926201.

16.1 Introduction
The Collision Detection algorithm (optional feature) allows the system to stop the robot
arm motion, as soon as any noise force on joints takes effect.
Such a capability can be enabled and disabled by the user, by means of a predefined
variable, using either a Program statement or a system Command

The Collision Detection functionality has NOT been designed in order to protect the
personnel, but to limit any damage to the robot mechanical parts and therefore to its
equipments!

Current chapter supplies information about the following topics:


– Basic concepts
– Activation/deactivation of Collision Detection function Collision Detection
functionality
– Collision Detection sensitivity type
– Reliability of Collision Detection functionality
– Notes about the collision detection use procedure
– Sample Programs.

16.2 Basic concepts


When enabled, the Collision Detection functionality allows detecting situations such as
– robot arm collisions with the surrounding environment
– stuck tips in welding operations,
– etc.
When a collision condition is detected (error message 62513SAX: collision detected),
the system may enter into a particular phase during which the robot gets compliant and
the emergency braking takes place

Compliance
The axes compliance has been used in order to be able to absorb part of the collision
energy (or part of the over-traction in case of stuck tips) and to minimize any possible
damage, this compliance can be activated by the user. Carefully assess its use in the

pr-0-0-gpr_06.fm
08/1012 169
Collision Detection (optional feature)

application.

Severity of collision error


The severity of the collision error can be changed by bringing it from 10 (that causes a
DRIVE OFF) to 8 (that generates a HOLD). To do this, set the new predefined variable
$COLL_EFFECT ($ARM_DATA field ) to the value:
– 0 to generate, in the case of collision, a DRIVE OFF;
– 1 to set the machine in HOLD state.
– 2 to generate the system event 197 that indicates "collision detected"

The robot DOES NOT STOP, but continues the programmed motion: it is the
responsibility of the user to appropriately deal with the event that has occurred,
cancelling the current motion, that would continue towards the obstruction, and
programming the new trajectory.
In the par. 16.7.4 Managing "collision detected" event on page 182, there is an example
program.

If it is wished, in the case of a severity 8 alarm, to activate the compliance mode, it is


better to increase the SoftServo after collision ($TUNE[25]) time-out bringing it from 600
(default) to 1000 or 1200.
This way of managing the Collision Detection is useful for "Pallet Search" applications
in the robot operating area: the arm moves along a Cartesian direction and when it
meets the pallet it stops, remaining fed, instead of generating an error and passing in
DRIVE OFF.

16.3 Activation/deactivation of Collision Detection


function
Since System Software release 2.02, Collision Detection handling is changed.
In order to enable the Collision Detection functionality, it is enough to set
$CRNT_DATA[num_arm].COLL_ENBL predefined variable to TRUE, by either a
Program Statement or a System Command:
$CRNT_DATA[num_arm].COLL_ENBL := TRUE
By default, it is not reset by the system upon each DRIVE OFF command; it continues
to be working until the user consciously decides to disable it, by setting the mentioned
above flag to FALSE.
It is also possible to change to the operating mode for automatically disabling the
Collision Detection functionality, setting to 1 bit number 10 of
$ARM_DATA[num_arm].A_ALONG_1D[12] predefined variable, by means of the
BIT_SET built-in.

BIT_SET($ARM_DATA[num_arm].A_ALONG_1D[12], 10)
The bit modification is allowed both at run-time and by means of the configuration file,
and it is possible to save it into the configuration file .C5G.

Compliance
After a collision alarm, the robot stop may be made compliant. The compliance

pr-0-0-gpr_06.fm
170 08/1012
Collision Detection (optional feature)

occurrence after collision is stated by setting to 1 bit number 11 of


$ARM_DATA[num_arm].A_ALONG_1D[12] predefined variable, and it is up to the user
to enable it by inserting in his program the following statement:

BIT_SET($ARM_DATA[num_arm].A_ALONG_1D[12], 11).
Such a flag can be disabled by means of the following statement:

BIT_CLEAR($ARM_DATA[num_arm].A_ALONG_1D[12], 11).
To avoid that this bit is unintentionally saved in .C5G and enables the compliance
service linked to the Collision Detection unexpectedly after a restart, the bit itself will be
automatically reset by the system during the start-up.

16.4 Collision Detection sensitivity type


A detailed description follows of the predefined variables which are involved in the
Collision Detection functionality. They are:
– $COLL_TYPE
– $ARM_SENSITIVITY (sensitivity threshold of the axes)
– $COLL_SOFT_PER (axes compliance thresholds)

16.4.1 $COLL_TYPE
In order to define the Collision Detection sensitivity type, it is available $COLL_TYPE
predefined variable. The allowed values for such a predefined variable are as follows:
– COLL_LOW
– COLL_MEDIUM
– COLL_HIGH
– COLL_MANUAL
initialized by COMAU, and
– COLL_USER1
– COLL_USER2
– ...
– ...
– COLL_USER10
that can be handled by the user to customise COMAU data.
During a Program execution, while some particular arm movements are performed, it is
possible that an occurring collision should be detected using more or less sensitivity.
The collision sensitivity can be modified both for a MOVE sequence and for just one
MOVE statement.
Modal assignment (for the whole MOVE sequence):
$CRNT_DATA[num_arm].COLL_ENBL := TRUE
$COLL_TYPE:= COLL_MEDIUM
MOVE TO PNT0001J
MOVE TO PNT0002J

pr-0-0-gpr_06.fm
08/1012 171
Collision Detection (optional feature)

In the shown above example, the collision sensitivity takes effect for both the MOVE
statements.
Nodal assignment (for just one MOVE statement):
$CRNT_DATA[num_arm].COLL_ENBL := TRUE
$COLL_TYPE := COLL_LOW
MOVE TO PNT0001J
MOVE TO PNT0002J WITH $COLL_TYPE := COLL_HIGH
In the shown above example, the first MOVE statement is executed using a LOW
collision sensitivity, while the second one is performed using a HIGH collision sensitivity.
A set of values corresponds to each value of $COLL_TYPE for the axes sensitivity,
$ARM_SENSITIVITY and a set of values (if any) for the compliance of
$COLL_SOFT_PER (just in the case in which the compliance modality after collision
has been enabled). Basic values (HIGH, MEDIUM, LOW, MANUAL) are set by COMAU.
COLL_USER1 and COLL_USER2 values can be used under the care and the
responsibility of the user.

When the Collision Detection functionality is enabled in PROGR state (jog, ProgramEdit,
etc.), the COLL_MANUAL corresponding thresholds (which
means $ARM_SENSITIVITY [COLL_MANUAL,nax] and $COLL_SOFT_PER [C
OLL_MANUAL,nax] ) are used, regardless the current value of $COLL_TYPE.

16.4.2 $ARM_SENSITIVITY (sensitivity threshold of the axes)


This bidimensional array represents the sensitivity threshold for each robot axis, used
by the Collision Detection algorithm. Maximum sensitivity is 100, minimum is 0.
The first dimension is the one of all possible values of $COLL_TYPE. The second one
is the axis number. Example: $ARM_SENSITIVITY[COLL_LOW, 1]
The calculation of the Collision Detection sensitivity thresholds is possible by means of
a built-in that can be run while the robot executes the work cycle.
The characteristics of this built-in are the following:

ARM_COLL_THRS(Arm, Coll_type, Time, Margin)


– Arm is the arm where the acquisition is to be made.
– Coll_type is the type of sensitivity for acquisition: the built-in will go directly to load
the $ARM_SENSITIVITY variables for the specified Coll_type. To obtain the
optimizing of the sensitivity thresholds, the types of collision increase from 6 to 14,
with the introduction of the types from COLL_USER3 to COLL_USER10.
– Time is the time, in seconds, that the acquisition lasts, and it has to correspond to
at least the duration of the path for which the thresholds are to be valid (a work
cycle or a single motion). It may be from 1 to 300 seconds.

pr-0-0-gpr_06.fm
172 08/1012
Collision Detection (optional feature)

Values 1 and 0 of the Time parameter, have the following meaning:


– 1 - indicates to start the data acquisition in order to calculate the sensitivity
thresholds
– 0 - indicates to stop the data acquisition and to assign the sensitivity
thresholds.
Example of usage:
ARM_COLL_THRS(1,COLL_USER7,1)
MOVE ...
....
MOVE ...
ARM_COLL_THRS(1,COLL_USER7,0)

– Margin is a flag (TRUE/FALSE) that defines whether the thresholds are to be


calculated with a margin of variability (TRUE, default value) or exactly on the
assigned path (FALSE).
The value of the variability margin is contained in the predefined variable
$A_ALONG_2D[10,ax] that will be initialised, in the configuration file, with the value
{7,7,6,6,6,0,0,0,0} which means 7% of the drive full scale on the first 3 axes, and
6% on the wrist axes (value determined experimentally). The privileged user can
change this margin.
For example,
ARM_COLL_THRS(1, COLL_USER2, 60, FALSE)
Acquires the data starting from the instant the built-in is executed and for the next 60
seconds: the end being indicated with the message

62520 - 02 SA DETERMINATION OF THE COLLISION CONCLUDED THRESHOLD


loads the values obtained, with no variability margin, in the predefined variables
$ARM_SENSITIVITY[COLL_USER2, ax].
The built-in can be used in a PDL2 program, linked to opportune CONDITIONS, to
adjust the sensitivity thresholds should the movement execution conditions change.

It is to be noted that the recalculation requires the same time as for the acquisition,
before the new thresholds can be actuated. During this time, the active thresholds (i.e.
the current ones) could cause false collisions or poor sensitivity.
Opportune measures, such as to use the standard safety thresholds during the
transition stage (from the start of the built-in execution to the receiving of the message)
should allow the acquisition phase to be overcome.

16.4.3 $COLL_SOFT_PER (axes compliance thresholds)


This predefined variable represents the compliance percentage for each robot axis, in
the compliance condition (when enabled), caused by a detected collision. Maximum
compliance percentage is 100, minimum is 0.
The first dimension is one of all possible values of $COLL_TYPE. The second one is the
axis number. Example: $COLL_SOFT_PER[COLL_HIGH, 3]

pr-0-0-gpr_06.fm
08/1012 173
Collision Detection (optional feature)

16.5 Reliability
In order to make the Collision Detection algorithm to operate in a safe and reliable way,
it is ABSOLUTELY REQUIRED that the user properly identifies the payload.
The Collision Detection performance strictly depends on a proper declaration of the
currently used payload: if the estimated payload is wrong, the Collision Detection could
be misevaluated (i.e. false collision during a Program execution); furthermore, while in
the compliance phase, with consequent deceleration and stop, the robot arm could have
unpredictable behaviours due to either an underestimated or an overestimated payload.

For these reasons, before activating the Collision Detection function, the user is to check
that the load used has been defined precisely.

16.6 Notes about the collision detection use procedure


– Introduction
– Use of the Collision Detection Procedure

16.6.1 Introduction
The following remarks are provided to help the user in setting up the Collision Detection
functionality.
The essential condition for the Collision Detection functionality to work properly is that
the dynamic model of the currents does exist for the related arm/robot. Only if the robot
is provided with such a dynamic model, it is possible to activate the functionality (if the
optional feature is present/purchased).
The dynamic model is able to calculate in advance the currents that will be used to move
the robot in a specific motion, using robot position, payload and inertia data. Today all
robots (except auxiliary axes) are provided with dynamic model.
In order to obtain the best performances from the dynamic model, it is NECESSARY to
have properly configured the following payload variables:
– $TOOL_MASS
– $TOOL_CNTR
– $TOOL_INERTIA
It is the operator’s care either to insert the nominal data or to use (if present/purchased)
the Payload Identification Program (optional feature), to modify the above listed values
while the application program is running, so the current payload values are always
defined for the Controller.
The Collision Detection functionality operates using the currents calculated in advance
by the dynamic model and the actual currents of each axis motor during the movement.
Such a functionality warns the user that a collision occurred. The Collision Detection
functionality works using the currents which are calculated in advance by the dynamic
model and the currents actually used in each motor (axes) movements. The functionality
warns the user about the occurring collision on one or more axes, if the difference

pr-0-0-gpr_06.fm
174 08/1012
Collision Detection (optional feature)

between the two above mentionned currents is significantly big.

VERY IMPORTANT! Remeber that the Collision Detection functionality has been
designed to limit any damage to the robot and therefore to its equipment, in case of
collision. So, since it is a functionality that immediately acts to limit the collision effect, it
is expectable it also limits damages to the equipment of the cell where the robot works
in. But it is important to understand that the Collision Detection functionality has not been
designed to protect the operator in case of bad/wrong use of the robot.

When a collision error occurs, the robot is immediately put in DRIVE OFF state and the
following error message is issued:
62513 – 10 SAX COLLISION DETECTED
in order to reset the alarm state, the alarms latch command is to be used:
– ULLA command, or
– Alarm Page, Latched sub-page, Ack softkey, in case of use of Teach Pendant (for
further information see C5G Control Unit Use, chapter Use of the Teach
Pendant).

16.6.2 Use of the Collision Detection Procedure


Now, let’s go through Collision Detection variables setting. It is strongly recommended
to follow all the listed below steps:

a. What is to be done before enabling the Collision Detection?

a.1 It is necessary to have the final work program.

a.2 To identify the thresholds for the work cycle


Because of the sensitivity of the algorithm, there is a difference between identifying
the COLD ROBOT thresholds (robot stationary, has been in DRIVE OFF for hours,
if possible overnight) and WARMED ROBOT (a robot is considered WARMED
after it has performed at least 15-20 work cycles).
To be certain that false collisions will not occur, the thresholds are to be identified
with the machine COLD.

Identifying the thresholds with the robot COLD limits, to a certain extent, the sensitivity
of the algorithm. The rules for use that are given below can help understand these
aspects and advise the user how to also make the function very sensitive.

If greater sensitivity is desired with WARMED ROBOT, 2 sets of thresholds have


to be identified:
• one for COLD ROBOT and
• one for WARMED ROBOT.
It will be the task of the user to provide a non-holdable PDL2 program that, at the
same time as the work cycle, manages the graduation of the thresholds from COLD
to WARMED and from WARMED to COLD, based on events (for example machine
stop for maintenance or a halt in the working activities and a restart) and the
associated timers.

pr-0-0-gpr_06.fm
08/1012 175
Collision Detection (optional feature)

Note that the thresholds definition does NOT take place inside this program, but in the
work program !

b. Splitting-up the program


The user program is to be splitted-up in some parts, in order to make it more
efficient end effective. For example:
– A: Via point movements
– B: short positioning movements
– C: technological movements (pick, drop, welding, etc.)
The user has to specify, for each type of movement, the right threshold which is
due both to the robot position and its payload.
When the program movements have been logically splitted-up, based upon the
different movement types, go to the following step.

c. Activating the functionality


In order to activate the functionality, it is enough to insert the following statement
at the program beginning:

$CRNT_DATA[num_arm].COLL_ENABLE:=TRUE

To deactivate it:

$CRNT_DATA[numero_arm].COLL_ENABLE:=FALSE

d. Definition of Nodal/ModalSensitivity
The system is provided with some predefined thresholds, for a general payload,
like the robot payload:
– COLL_LOW
– COLL_MEDIUM
– COLL_HIGH
While in programming state, the system automatically uses a 4th threshold:
– COLL_MANUAL
Two more thresholds exists which can be configured by the user:
– COLL_USER1
– COLL_USER2
– ...
– COLL_USER10

The sensitivity type can be defined in the program by means of two different
strategies:
• modal definition
...
$COLL_TYPE := COLL_xxxx
MOVE ...
...
this means that the chosen sensitivity threshold (COLL_xxxx) will be used
• nodal definition for all MOVE statements
MOVE ... WITH $COLL_TYPE:= COLL_xxxx (A)(see step b.)
...
MOVE ... WITH $COLL_TYPE:= COLL_yyyy (B)(see step b.)

pr-0-0-gpr_06.fm
176 08/1012
Collision Detection (optional feature)

this means that the chosen sensitivity threshold, (COLL_xxxx), will be used
for (A) type MOVEs; the other one, (COLL_yyyy), will be used for (B) type
MOVEs instead.

e. False collisions
If the user has chosen the thresholds (COLL_LOW, COLL_MEDIUM,
COLL_HIGH, COLL_MANUAL, COLL_USER) without analysing the type of
collision he would like to prevent, and some wrong thresholds have been set for the
movements included in the program, some False Collisions will occur; this means
, during the robot motion, the system will detect a collision which never happened.
The reason is that a threshold too sensitive for the movement has been used (for
example: too high sensitivity in a movement with high accelerations/decelerations).

f. What does the sensitivity percentage threshold mean?


For each axis, there is a maximum value of its deliverable current; for example, if
IMAX=60 A, saying that the axis sensitivity is 90%,it means:

(100% - 90%) * 60 A = 6 A

g. Use strategy
First of all the user must understand what he really does need:
– REQUIREMENT No.1: immediate use of the Collision Detection
functionality
The modal strategy is the one that allows the user to activate the Collision
Detection functionality and to set, for example, just one threshold for all
motion types (i.e. the user tries using COLL_MEDIUM, then, if any false
collisions occurred, switching to COLL_LOW). Obviously, the disadvantage of
such a strategy is that the Collision Detection sensitivity has not been tuned
by the user to have high performances. The advantage is that setting the
sensitivity is very fast.
Once the user program has run with Cold Robot (which means not working
for hours), if no false collisions are detected, the chosen threshold is good to
assure the Collision Detection activation without any false collisions.
Otherwise, it is needed to use a COLL_USERx threshold: they have the same
starting values as COLL_LOW, reduced by 3% for each axis.
– REQUIREMENT No. 2: customized use
The nodal strategy has been designed for advanced users who need to reach
a high level protection against collisions, stuck tips, pick/drop movements,
etc.
In such a situation, the user, after having logically grouped the program
movements, as suggested in step b., has to perform some more tests in order
to identify, for each movement, which is the threshold that guarantees the
highest level of protection.
Here follows some operating rules for any single motion.
• Consider a single movement and identify its motion type:
• Movement with high accelerations/decelerations (many centimetres) -->
(A) type movement (see step b.)
• Movement at maximum speed
• Short movement (few centimetres) --> (B) type movement (see step b.)
• Movement at reduced speed
• For (A) type movements, it is recommended to start with a COLL_MEDIUM
threshold \ for (B) type movements, start with COLL_HIGH
• Execute some motion cycles with Cold robot at 100% (max speed of program
execution). If no false collisions occur, the chosen threshold is the right one.

pr-0-0-gpr_06.fm
08/1012 177
Collision Detection (optional feature)

• Otherwise, if some false collisions occur, set the threshold to COLL_LOW (for
(A) type movements) or COLL_MEDIUM (for (B) type movements).
• If some false collisions still occur, initialize COLL_USER1 threshold to
COLL_LOW values:
$ARM_SENSITIVITY[COLL_USER1,ax:= $ARM_SENSITIVITY[COLL_LOW,ax]
• Decrease by 3% the value for each axis on which the false collision occurred
($ARM_SENSITIVITY[COLL_USER1,ax]) and try again until no false
collisions are detected.
• In the thresholds definition, it is recommended to try to keep uniformity in the
values of the main axes 1-2-3 and the wrist axes 4-5-6
• The thresholds resulting from the described above tests, are to be used for
any movement which is similar to the analysed one.
• As an alternative the ARM_COLL_THRS(Arm, Coll_type, Time, Margin)
built-in can be used to identify the collision thresholds runtime.

h. Programming tips
If the user would like to operate with the Nodal strategy, in order to obtain the
maximum results from the Collision Detection functionality, it is needed to follow
the listed below suggestions:
– avoid technological positions (i.e. Spot Welding positions) by means of an (A)
type movent, which means with big accelerations/decelerations. Insert a
small ‘approach’ movement.
– deactivate the Collision Detection functionality during the technological
operation (i.e. closing the gun). This is to avoid that unpredictable movements
of the equipments could generate torques on robot axes that could be seen
as a collision.

16.7 Sample Programs


The following sample Programs are provided:
– Enabling the Collision Detection functionality for a single MOVE statement
– Enabling Collision Detection again from within a Program
– Automatic calculation of the sensitivity thresholds
– Managing "collision detected" event
– Use of CDetect open source library.

pr-0-0-gpr_06.fm
178 08/1012
Collision Detection (optional feature)

16.7.1 Enabling the Collision Detection functionality for a single


MOVE statement

PROGRAM collision
VAR pnt0001j, pnt0002j, pnt0003j, pnt0004j : JOINTPOS FOR ARM[1]
BEGIN
CONDITION[1] :
WHEN AT START DO
$COLL_TYPE := COLL_HIGH
$CRNT_DATA[1].COLL_ENBL := TRUE
ENDCONDITION

CONDITION[2] :
WHEN AT END DO
$CRNT_DATA[1].COLL_ENBL := FALSE
ENDCONDITION

MOVE TO $CAL_SYS
CYCLE

MOVE TO pnt0001j
MOVE TO pnt0002j

-- activating the collision detection functionality when needed only

MOVE LINEAR TO pnt0003j WITH CONDITION[1], CONDITION[2]


MOVE TO pnt0004j
END collision

pr-0-0-gpr_06.fm
08/1012 179
Collision Detection (optional feature)

16.7.2 Enabling Collision Detection again from within a Program


To be used in the case in which Collision Detection is disabled upon DRV OFF.

PROGRAM collision2
VAR pnt0001j, pnt0002j, pnt0003j, pnt0004j : JOINTPOS FOR ARM[1]
BEGIN

CONDITION[1] NODISABLE :
WHEN EVENT 99 DO

-- enabling collision detection upon drive on (useful until 2.01 sw version)

$CRNT_DATA[1].COLL_ENBL := TRUE
ENDCONDITION

ENABLE CONDITION[1]

MOVE TO $CAL_SYS

-- activating collision detection in modal mode, low sensitivity

$COLL_TYPE := COLL_LOW
$CRNT_DATA[1].COLL_ENBL := TRUE
CYCLE

MOVE TO pnt0001j
MOVE TO pnt0002j

-- increasing the sensitivity for the movement to be monitored

MOVE LINEAR TO pnt0003j WITH $COLL_TYPE = COLL_HIGH


MOVE TO pnt0004j
END collision2

pr-0-0-gpr_06.fm
180 08/1012
Collision Detection (optional feature)

16.7.3 Automatic calculation of the sensitivity thresholds

-- Recalculates the collision sensitivity thresholds every delta_t minutes


--and at each GEN_OVR variation.
--
PROGRAM thresholds NOHOLD
VAR dummy : BOOLEAN
coll : INTEGER
delta_t : INTEGER

ROUTINE ru_thrs
BEGIN
-- Calculates the collision thresholds for ARM 1, 'coll' sensitivity type and
-- acquires data for 120 seconds.
ARM_COLL_THRS(1, coll, 120)
END ru_thrs

BEGIN
-- Variable to keep the program active
dummy := FALSE
-- Type of sensitivity for which the thresholds recalculation is asked
coll := COLL_USER3
--
-- Defines a delta time to recalculate the thresholds
--
delta_t := 60000 * 10 -- each 10 mins

CONDITION[1] NODISABLE :
--
-- Recalculates the thresholds if GEN_OVR changes
--
WHEN EVENT 85 DO
$TIMER[1] := 0
ru_thrs
ENDCONDITION

CONDITION[2]:
--
-- Recalculates the thresholds at the timeout.
--
WHEN $TIMER[1] > delta_t DO
$TIMER[1] := 0
ENABLE CONDITION[2]
ru_thrs
ENDCONDITION

ENABLE CONDITION[1]
ENABLE CONDITION[2]

-- Calculates the start thresholds


ru_thrs

-- Keeps the program active


WAIT FOR dummy
END thresholds

pr-0-0-gpr_06.fm
08/1012 181
Collision Detection (optional feature)

16.7.4 Managing "collision detected" event


Simply as an example, a program segment is given that manages the "collision
detected" event 197.

PROGRAM colltouch
VAR pnt0006p, pnt0007p, pnt0008p: POSITION
pnt0001p, pnt0002p, pnt0003p, pnt0004p, pnt0005p: POSITION
BEGIN

CONDITION[1]:
WHEN EVENT 94 DO
UNLOCK -- reset for
RESUME -- next restart
.
.
.
ENDCONDITION

CONDITION[2]NODISABLE:
WHEN EVENT 197 DO
LOCK -- locks the machine
CANCEL CURRENT -- cancels the current motion
.
.
.
ENDCONDITION
.
.
.
ENABLE CONDITION[1]
ENABLE CONDITION[2]

$COLL_TYPE:=COLL_USER1
$COLL_EFFECT:=2
$CRNT_DATA[1].COLL_ENBL:=TRUE

CYCLE
MOVE TO ...
.
.
.

END colltouch

pr-0-0-gpr_06.fm
182 08/1012
Collision Detection (optional feature)

16.7.5 Use of CDetect open source library


In UD:\SYS\UTIL directory, an open source library called CDetect is released, which
contains two exported routines, very important for the Collision Detection functionality.
At the system startup, SYS_STARTUP program executes the following steps:

a. if CDetect.cod DOES NOT exist in UD:\SYS\UTIL, .zip file is unzipped and


CDetect.cod file is created;

b. if CDetect.cod does exist, it verifies whether or not it has been generated by


Comau:

b.1 if so, the file is overwritten with a more recent version.

b.2 If it has NOT been generated by Comau (e.g. the user has modified/customized his
own CDetect version) the file is NOT updated, and the user original file is kept.
The two exported routines are associated to the motion statements, for starting and
ending the acquisition of the Collision thresholds to be used in such a motion section:
– CD_START (ai_coll) - indicates the beginning of the Collision thresholds
acquisition.
It is possible to specify a parameter (ai_coll) which is the number of the table
including the Collision thresholds associated to such a motion section.
– CD_END - indicates the end of the Collision thresholds acquisition. This routine
stops the acquisition and the motion segment, and freezes its corresponding
values.

In the program, the whole movement can be split into several sections, for a maximum
of 100 sections. By means of such routines it is possible to acquire the Collision
thresholds for each section, in an automatic way.
Identifying homogeneous motion sections (between CD_START and CD_END) makes
the calculated thresholds much more fine for their usage.
The Collision Detection functionality is activated by starting with cold thresholds and, at
each cycle, thresholds are calculated depending on the actual movement.
A third routine is also available:
– CD_READ - displays (on LUN_TP and LUN_CRT)
• the Collision current status (enabled/disabled),
• current collision type ($COLL_TYPE)
• the sensitivity thresholds for every single axis.
An example follows of the described above routines application.

pr-0-0-gpr_06.fm
08/1012 183
Collision Detection (optional feature)

PROGRAM mov

VAR pnt0001j, pnt0002j, pnt0003j, pnt0004j : JOINTPOS FOR ARM[1]

-- EXPORTED ROUTINES
ROUTINE CD_Start(ai_Coll : INTEGER) EXPORTED FROM CDetect
ROUTINE CD_End EXPORTED FROM CDetect
ROUTINE CD_Read EXPORTED FROM CDetect

BEGIN

MOVE TO $CAL_SYS
CYCLE
CD_START(1)
MOVE TO pnt0001j
MOVE TO pnt0002j
CD_END

CD_START(2)
MOVE LINEAR TO pnt0003j
MOVE TO pnt0004j
CD_END
END mov

pr-0-0-gpr_06.fm
184 08/1012
Use of Positioners managed by C5G

17. USE OF POSITIONERS MANAGED BY C5G

17.1 Introduction
This chapter is addressed to the installers and maintenance engineers of the automated
cell, to supply them with the use procedures and the information needed for the
Controller software configuration so to obtain the correct management of the positioner
equipped with robot external axes.
In particular the need is underlined to carry out the positioner configuration customising
when this is not a standard product.

In any case, even with a standard positioner, the radius of the part overall dimensions
always has to be defined.

The positioners are divided into families, and a paragraph is dedicated to each of them.
The procedures and conventions contained in the following paragraphs are very
important to ensure the consistency of the installation and above all the correct
functioning of the system when, for example, the cooperative motion is used, i.e. the
enslavement of a robot in the position of the part to be processed mounted on the
positioner.

It is the responsibility of the positioner designer to check and guarantee that the unit
operates in conformity with the relevant standards. In particular it must be verified that
in the following situations:
– normal use (Automatic/Programming),
– emergency stop,
– safety braking,
– Hold,
– Drive off,
– impact on any mechanical pads
the unit behaves in a manner that complies with current safety standards.

17.2 Summary

The following subjects:


– USE of the Teach Pendant (use of the external axes configuration software)
and
– USE of the TO_SET program (calculation of positioner base position),
are dealt with respectively:
– in the Use of the C5G Control Unit Use Manual, in the paragraph Setup Page,
and
– in this manual, Chap. TO_SET Program - Tool handling

hs-0-0-mot_04.fm
00/0210 185
Use of Positioners managed by C5G

The positioners described herein are grouped as follows:


– Positioners with 1 rotating axis type MP, PTDO, PTDV, TR3000/6000
– PTORB - Positioner with 2 perpendicular axes
– Positioners with 2 non perpendicular axes, type PTORB-alfa
– Integrated robot positioning axes
The following indications are contained for each of the above topics:
– definition mode of base and flange reference systems,
– how to execute the calibration and
– characteristic parameters for the positioner kinematic description.

17.3 General Conventions


Conventions regarding axis rotation and mechanical location of points P1, P2 and P3 (to
calculate cooperated motion) are described, to be used for positioner models managing
two axes.
These conventions acquire importance when a cooperative motion is to be executed,
i.e. to enslave a robot to the position of the part mounted on the positioner: if they are
not followed it will not be possible to correctly measure the positioner base position by
means of the TO_SET program (see Chap. TO_SET Program - Tool handling).

For special conventions and specifications of each positioner, see the relevant
paragraph for that particular model or family.

– Axis rotation directions


– Convention for the mechanical positioning of points P1, P2 and P3

17.3.1 Axis rotation directions

The directions of the positioner axis rotations cannot be chosen at will: they have
to strictly follow the convention in which the axes have a positive anticlockwise
direction (in relation to the rotation axis)..

In other words they have to follow the right-hand rule referring to the direction indicated
in Fig. 17.1 in correspondence to the axes: pointing the thumb of the right hand in the
direction of the dashed line arrow (that represents each axis), the fingers are to close in
the positive direction of the rotating axis. For this description, the orbital positioner has
been chosen because it is particularly representative.

17.3.2 Convention for the mechanical positioning of points P1,


P2 and P3
The references for points P1, P2, P3 described in the Chap. TO_SET Program - Tool
handling to calculate the base of the positioners ($BASE if the positioner is an

hs-0-0-mot_04.fm
186 00/0210
Use of Positioners managed by C5G

independent arm or $AUX_BASE if it is a group of auxiliary axes) are to be mechanically


positioned according to the following convention (see Fig. 17.1):
– P1 and P3 are to be chosen along the Yflange axis, with positive direction from P1
to P3 (P1 in the negative part of Yflange and P3 in the positive part);
– The origin of the flange reference Oflange is to coincide with the mean point of
segment P1-P3;
– P2 is to be chosen so that the segment between Oflange and P2 is perpendicular to
P1-P3.

Fig. 17.1 - Mechanical positioning of P1, P2 and P3

1 - axis 1 2 - axis 2

Xb, Yb, Zb, Ob= Xbase, Ybase, Zbase, Obase


Xf, Yf, Zf, Of = Xflange, Yflange, Zflange, Oflange

17.4 Programming override value calculation


To comply with the safety standards in force for robots and positioners, a configuration
tool is provided on the Teach Pendant (SETUP page, AUX_AXES sub-page). This
calculates the speed value in manual mode.
The following formula is used:

where:

hs-0-0-mot_04.fm
00/0210 187
Use of Positioners managed by C5G

250 = maximum speed allowed as per standard [mm/s]


955 = numeric conversion factor
Rt = motor transmission ratio [Mt/axt]
Vm = motor maximum speed [Rpm]
r = part overall dimension radius [mm]

MAXIMUM PROGRAMMING SPEED


It is very important that the calculation is made with extreme accuracy, so as to meet the
requirements of current safety standards. If parts are machined that have very different
dimensions, the worst case is to be used for the calculation (part maximum overall
dimensions).
The override value is inserted with the configuration tool.

17.5 Positioners with 1 rotating axis type MP, PTDO,


PTDV, TR3000/6000

17.5.1 Definition of the reference system


The reference system for the lathe positioner flange (bearing plate) is defined according
to the following conventions (see Fig. 17.2):
– the flange reference system origin (Oflange) lays on the surface of the flange
coinciding with the positioner axis rotation centre;
– the Zflange axis is to be perpendicular to the flange surface with outward direction.

Fig. 17.2 - Definition of the reference system

1 - axis 1 Xf, Yf = Xflange, Yflange

Note the convention that concerns points P1, P2, P3 described in the Chap. TO_SET
Program - Tool handling for the $BASE (or $AUX_BASE) calculation of the positioners.
Note also how the axis has an anticlockwise direction of rotation to comply with the
right-hand rule convention (see Axis rotation directions).

If, operating with the Teach Pendant, the controlled axis moves in the opposite direction
to this rule, the transmission ratio sign must be changed using the Teach Pendant

hs-0-0-mot_04.fm
188 00/0210
Use of Positioners managed by C5G

17.5.2 Calibration
The lathe positioner does not require special rules for the calibration position.

17.5.3 Kinematic description

To configure these positioners, see the C5G Control Unit Use Manual, Setup Page,
paragraph AUX_AXES.

For these types of positioners no value has to be inserted regarding the length of the
axes.
On the other hand, when programming, it is necessary to calculate the speed to be
attributed to the positioner axis, according to the dimension of the part that is mounted
on the bearing plate, so that the maximum tangential speed does not exceed 250 mm/s
(see standards in force). Therefore it is necessary first of all to measure the maximum
radius r of the part to be machined, as indicated in Fig. 17.3.

Fig. 17.3 - Part maximum radius measurement

1 - Part to be machined 2 - Lathe bearing plate

Next, the configuration software, on the Teach Pendant, calculates the manual mode
speed value.
A table summarising the mechanical data to be entered is shown below, assuming that
the positioner is axis 7.

For very long lathes, it is possible to mount the robot on an SCP slide or CRP column
integrated axis; in this case the integrated axis will be axis 7, whereas the lathe will
become axis 8

OPTION AXIS VALUE


Axis length [mm] 7 /
Type of axis 7 ROTATING
Axis offset [mm] 7 /
Programmed speed override 7 X

hs-0-0-mot_04.fm
00/0210 189
Use of Positioners managed by C5G

17.6 PTORB - Positioner with 2 perpendicular axes


– Positioner with two tilting-rotating axes
– Positioner with two axes in "L" arrangement

17.6.1 Positioner with two tilting-rotating axes

17.6.1.1 Definition of the reference system


The positioner base reference system is defined by the following conventions (see
Fig. 17.4):
– the origin of the positioner base reference system (Obase) lays on the bearing
surface (typically the floor);
– the Zbase axis is perpendicular to the bearing surface and in upward direction;
– the Xbase axis lays on the bearing surface with direction parallel to the positioner
first rotation axis;
– the Ybase axis is therefore on the resting surface perpendicular to the positioner first
rotation axis.
The positioner flange reference system is defined according to these conventions (see
Fig. 17.4):
– the origin of the flange reference system (Oflange) lays on the flange surface that
coincides with the centre of rotation of the positioner second axis;
– the Zflange axis is perpendicular to the flange surface with outward direction.

17.6.1.2 Calibration
The calibration conventions are the following:
– the first axis is to calibrate so that the Zflange axis is aligned to Zbase.
– the second axis is to calibrate with all the flange reference axes parallel to the
corresponding axes of the base reference; in particular Yflange is to be parallel to
Ybase and have the same direction.

Both of these conditions are important: an approximation in relation to one of these will
jeopardise the machine precision during cooperative motion (the robot does not hold
the position on the part).

Also the convention should be borne in mind that concerns points P1, P2, P3 described
in the Chap. TO_SET Program - Tool handling to calculate $BASE (or $AUX_BASE) of
the positioners (see Fig. 17.4).

hs-0-0-mot_04.fm
190 00/0210
Use of Positioners managed by C5G

Fig. 17.4 - Definition of the reference system

1 - axis 1 2 - axis 2 Xf, Yf = Xflange, Yflange Xb, Yb = Xbase, Ybase

17.6.1.3 Kinematic description

To configure these positioners, see the C5G Control Unit Use Manual, Setup Page,
paragraph AUX_AXES.

The parameters required for the correct kinematic description of the positioner (length
of axes) are indicated in Fig. 17.5. This shows a generic positioner indicating the
dimensions that distinguish it and the PDL2 variables that contain the parameters. Note
that the model requires that axes 1 and 2 intersect (there must be no offset).
It is also necessary to calculate the speed to be attributed to the two positioner axes
being programmed, according to the dimension of the part that is mounted on the
bearing plate, so that the maximum tangential speed does not exceed the set value of
250 mm/s. Therefore it is necessary to first measure the maximum radii r1 and r2 of the
part to be machined, as indicated in Fig. 17.5.

Fig. 17.5 - Parameters for the positioner kinematic description

1 - axis 1 2 - axis 2 3 - part to be machined


$AX_LEN[ax_logic1] = L 1 $AX_OFST[ax_logic2] = L2
For example, for positioner formed by auxiliary axes 7 and 8: ax_logic1 = 7 e ax_logic2 = 8

hs-0-0-mot_04.fm
00/0210 191
Use of Positioners managed by C5G

If the part has overall dimensions that are less than the diameter of the bearing plate, r2
is to be equal to the radius of the bearing plate. This is to always consider the worst case
of part maximum overall dimensions or of the mechanical structure of the positioner in
motion.

Next, the configuration software, on the Teach Pendant, calculates the manual mode
speed value.
Two tables follow, summarising the useful mechanical data, assuming that the
positioner is handled with auxiliary axes 7 and 8 respectively.

OPTION AXIS VALUE


Axis length [mm] 7 L1
Axis type 7 ROTATING
Axis offset [mm] 7 /
Program speed override 7 X1

OPTION AXIS VALUE


Axis length [mm] 8 /
Axis type 8 ROTATING
Axis offset [mm] 8 L2
Program speed override 8 X2

17.6.2 Positioner with two axes in "L" arrangement

17.6.2.1 Definition of the reference system


As can be noted, the positioner base reference system is in an unusual position in
relation to the other positioners, that is to say, its origin does not lay on the bearing
surface but is displaced in correspondence to axis 2 (seen from above). This happens
because the software uses the same mathematic model of the tilting-rotating positioner
that does not support this type of offset.
The positioner base reference system is defined according to these conventions (see
Fig. 17.6):
– The origin of the positioner base reference system (Obase) lays on the level of the
bearing surface, (typically the floor) on the extension of rotation axis 2;
– the Zbase axis is perpendicular to the bearing surface and in upward direction;
– the Xbase axis lays on the bearing surface with direction parallel to the first rotation
axis of the positioner;
– the Ybase axis is therefore on the bearing surface in perpendicular direction to the
first rotation axis of the positioner.
The positioner flange reference system is defined according to the following conventions
(see Fig. 17.6):

hs-0-0-mot_04.fm
192 00/0210
Use of Positioners managed by C5G

– the origin of the flange reference system (Oflange) lays on the surface of the flange
to coincide with the centre of rotation of the positioner second axis;
– the Zflange axis is perpendicular to the flange surface with outward direction.

17.6.2.1.1 Calibration
The conventions for the calibration are as follows:
– The first axis is to be calibrated so that the Zflange axis is aligned to Zbase;
– The second axis is to calibrate with all the flange reference axes parallel to the
corresponding base reference; in particular Yflange is to be parallel to Ybase and
have the same direction.

Both of these conditions are important: an approximation in relation to one of these will
jeopardise the machine precision during cooperative motion (the robot does not hold the
position on the part.).

Also the convention is to be borne in mind that concerns points P1, P2, P3 described in
Chap. TO_SET Program - Tool handling to calculate the $BASE (or $AUX_BASE) of the
positioners (see Fig. 17.6).

Fig. 17.6 - Definition of the reference system

1 - axis 1 2 - axis 2 X b, Yb, Zb, Ob= Xbase, Ybase, Zbase, Obase


Xf, Yf, Zf, O f = Xflange, Yflange, Zflange, Oflange

hs-0-0-mot_04.fm
00/0210 193
Use of Positioners managed by C5G

17.6.2.2 Kinematic description

To configure these positioners, see the C5G Control Unit Use Manual, Setup Page,
paragraph AUX_AXES.

The parameters required for the correct kinematic description of the positioner (length
of axes) are indicated in Fig. 17.7. They show a generic positioner with the dimensions
that distinguish it and the PDL2 variables that contain the parameters. As can be seen,
a length of the arm that carries axis 2 is not available, but only the two heights; this is
possible because the positioner base reference system is centred on rotation axis 2 (see
Fig. 17.7). ). Note also that the value for L2 is to be negative to indicate that the flange
(axis 2) is lowered in relation to axis 1.
It is also necessary to calculate the speed to be attributed to the two positioner axes
being programmed, according to the size of the part mounted on the bearing plate, so
that the maximum tangential speed does not exceed the set speed of 250 mm/s. To this
purpose it is necessary first of all to measure the maximum r1 and r2 radii of the part to
be machined, as indicated in Fig. 17.7.

Fig. 17.7 - Parameters for the kinematic description of the positioner

1 - axis 1 2 - axis 2 3 - part to be machined

$AX_LEN[ax_logic1] = L1 $AX_OFST[ax_logic2] = -L2

For example, for a positioner formed by auxiliary axes 7 and 8: ax_logic 1 = 7 e ax_logic 2 = 8

If the part has overall dimensions that are less than the diameter of the bearing plate, r2
is to be equal to the radius of the bearing plate; in the same way for r1 a minimum value
is to be used equal to r1m to take into consideration the mechanical structure of axis 7.
This is to always consider the worst case of part maximum overall dimensions or of the
mechanical structure of the positioner in motion

Next, the configuration software, on the Teach Pendant, calculates the manual mode
speed value.
Two tables follow that summarise the useful mechanical data, assuming that the
positioner is handled with auxiliary axes 7 and 8 respectively.

hs-0-0-mot_04.fm
194 00/0210
Use of Positioners managed by C5G

OPTION AXIS VALUE


Axis length [mm] 7 L1
Axis type 7 ROTATING
Axis offset [mm] 7 /
Program speed override 7 X1

OPTION AXIS VALUE


Axis length [mm] 8 /
Axis type 8 ROTATING
Axis offset [mm] 8 -L2
Program speed override 8 X2

17.7 Positioners with 2 non perpendicular axes, type


PTORB-alfa

17.7.1 Definition of the reference system


The positioner base reference system is defined according to the following conventions
(see. ):
– The origin of the positioner base reference system (Obase) lays on the bearing
surface(typically the floor);
– the Zbase axis is perpendicular to the bearing surface and in upward direction;
– the Xbase axis lays on the bearing surface and is perpendicular to the two axes of
the positioner;
– the Ybase axis consequently results with the direction indicated in .
The positioner flange reference system is defined according to the following conventions
(see ):
– The origin of the flange reference system (Oflange) lays on the flange surface
coinciding with the centre of rotation of the positioner second axis;
– the Zflange axis is perpendicular to the flange surface with outward direction.

hs-0-0-mot_04.fm
00/0210 195
Use of Positioners managed by C5G

Fig. 17.8 - Definition of the reference systems

1 - axis 1 2 - axis 2
Xb, Yb, Zb, Ob= Xbase, Ybase , Zbase, Obase Xf, Yf, Zf, Of = Xflange, Yflange, Zflange, O flange

17.7.2 Calibration
The conventions for the calibration are as follows:
– the first axis is to be calibrated so that the Zflange axis is parallel to Zbase;
– the second axis is to calibrate with all the flange reference axes parallel to the
corresponding ones of the base reference; in particular Yflange is to be parallel to
Ybase and have the same direction.

Both of these conditions are important: an approximation in relation to one of these will
jeopardise the machine precision during cooperative motion (the robot does not hold the
position on the part).

Also the convention is to be borne in mind that concerns points P1, P2, P3 described in
the Chap. TO_SET Program - Tool handling to calculate the $BASE (or $AUX_BASE)
of the positioners (see Fig. 17.8).

17.7.3 Kinematic description

To configure these positioners, see the C5G Control Unit Use Manual, Setup Page,
paragraph AUX_AXES.

The parameters required for the correct kinematic description of the positioner (length
of axes and angles) are shown in the Fig. 17.9. It illustrates a generic positioner
indicating the dimensions that distinguish it and the PDL2 variables that contain the
parameters.
It is also necessary to calculate the speed to be attributed to the two positioner axes

hs-0-0-mot_04.fm
196 00/0210
Use of Positioners managed by C5G

being programmed, according to the dimension of the part that is mounted on the
bearing plate, so that the maximum tangential speed does not exceed 250 mm/s.
Therefore it is necessary first of all to measure the maximum radii r1 and r2 of the part
to be machined, as indicated in the following Fig. 17.9.

Fig. 17.9 - Parameters for the kinematic description of the positioner

1 - part to be machined

$AX_LEN[ax_logic1] = L 1 $AX_LEN[ax_logic2] = L3
$AX_OFST[ax_logic1] = alpha, with alpha that is not 90° $AX_OFST[ax_logic2] = L2
For example, for a positioner formed by auxiliary axes 7 and 8: ax_logic1 = 7 e ax_logic2 = 8

If the part has overall dimensions that are less than the diameter of the bearing plate, r2
is to be equal to the radius of the bearing plate r2m; in the same way for r1 a minimum
value is to be used equal to r1m to take into consideration the mechanical structure of
axis 7. This is to always consider the worst case of part maximum overall dimensions or
of the mechanical structure of the positioner in motion..

Next, the configuration software, on the Teach Pendant, calculates the manual mode
speed value.
Two tables follow, summarising the useful mechanical data, assuming that the
positioner is handled with auxiliary axes 7 and 8 respectively.

OPTION AXIS VALUE


Axis length [mm] 7 L1
Axis type 7 ROTATING
Axis offset [mm] 7 *
Program speed override 7 X1

Note that the absolute value of the alpha angle is to be inserted even if the measurement
unit of the axis offset is in millimetres.

OPTION AXIS VALUE


Axis length [mm] 8 L3

hs-0-0-mot_04.fm
00/0210 197
Use of Positioners managed by C5G

Axis type 8 ROTATING


Axis offset [mm] 8 L2
Program speed override 8 X2

17.8 Integrated robot positioning axes


– Integrated slide
– Integrated rotating column
– Three linear axes portal
– Two linear axes Portal
– Integrated trans-rotational Column

17.8.1 Integrated slide


Regarding the configuration of a robot resting on a linear slide handled by an auxiliary
axis.
By integrated motion it is intended that the calculation of the TCP position takes into
account the position of the slide (only X axis). In other words, the slide is integrated in
the direct kinematics of the system of axes.
This has two practical effects:
– The Cartesian positions (POSITION) are defined in the cell space regardless of the
linear slide axis position and therefore moving only the slide will change the
Cartesian position;
– Manually moving the slide (jog) in a Cartesian reference (for example jog BASE),
the TCP position remains unchanged due to the displacement of the robot axes
that offset the displacement.

On the Teach Pendant the linear axis can be moved in Cartesian mode, using the 7+
and 7- keys and it is not possible to enable or disable the slide integration in real time (a
Controller restart is needed).

17.8.1.1 Definition of the reference system


The integrated slide base reference system is defined according to these conventions
(see Fig. 17.10):
– The origin of the slide base reference system (Obase) lays on the bearing surface
(typically the floor);
– the Zbase axis is perpendicular to the bearing surface and in upward direction;
– the Xbase axis lays on the bearing surface and orientated in the direction of the
positive stroke;
– the Ybase axis consequently results with the direction indicated in Fig. 17.10.
The Z axis reference of the $BASE variable to the slide is not managed and therefore
this remains linked to the position of the robot base.
On the slide there is the mounting flange of the robot base that can only be positioned

hs-0-0-mot_04.fm
198 00/0210
Use of Positioners managed by C5G

standing with the base always perpendicular to the slide motion axis.
Vice-versa 4 robot base orientation positions are allowed (at 90° intervals ) in relation
to the slide base (see Fig. 17.12).

Fig. 17.10 - Definition of the reference system

1. slide base reference


2. robot base
Xbs , Ybs, Zbs = Xbase_slide, Ybase_slide, Zbase_slide
Xbr, Ybr, Zbr = Xbase_robot, Ybase_robot, Zbase_robot

17.8.1.2 Calibration
The slide calibration position is fixed close to the negative limit of the stroke and marked
with a zero notch.
Since this is an integrated axis it is not treated as a positioner for the part to be machined
and therefore it is not necessary to pick up points P1, P2 and P3 described in the
Chap. TO_SET Program - Tool handling.

17.8.1.3 Kinematic description

To configure these positioners, see the C5G Control Unit Use Manual, Setup Page,
paragraph AUX_AXES.

The parameters needed for the correct kinematic description of the integrated slide are
indicated in Fig. 17.11.
Next, the configuration software, on the Teach Pendant, calculates the manual mode
speed value.
A table follows summarising the useful mechanical data, bearing in mind that it is
mandatory that the integrated slide is handled with auxiliary axis 7.

hs-0-0-mot_04.fm
00/0210 199
Use of Positioners managed by C5G

OPTION AXIS VALUE


Axis length [mm] 7 L
Axis type 7 TRANSLATING
Axis offset [mm] 7 /
Program speed override 7 X

Fig. 17.11- Parameters for the kinematic description of the integrated


slide

L = slide useful stroke


Xbs, Ybs, Zbs = Xslide_base, Yslide_base, Zslide_base

Besides the L and H geometrical data indicated above, for the complete kinematic
description of the integrated slide also the assembly angle is to be defined:
– 180° rotation ==> Xrobot_base in opposite direction to Xslide_base;
– 0° rotation ==> Xrobot_base in the direction of Xslide_base;
– 270° rotation ==> Xrobot_base in opposite direction to Yslide_base ;
– 90° rotation ==> Xrobot_base in the direction of Yslide_base;

Fig. 17.12- Assembly angle

Xbs, Ybs = Xslide_base, Yslide_base Xbr, Ybr = Xrobot_base, Yrobot_base

hs-0-0-mot_04.fm
200 00/0210
Use of Positioners managed by C5G

17.8.2 Integrated rotating column


Regarding the configuration of a robot resting on or hanging from a lever on the rotating
column handled by an auxiliary axis .
By integrated motion it is intended that the calculation of the TCP position takes into
account the position of the column. In other words, the column is integrated in the direct
kinematics of the system of axes.
This has two practical effects:
– The Cartesian positions (POSITION) are defined in the cell space regardless of the
rotating column axis position and therefore moving only the column will change the
Cartesian position;
– Manually moving the column (jog) in a Cartesian reference (for example jog
BASE), the TCP position remains unchanged due to the displacement of the robot
axes that offset the lever displacement ;

On the Teach Pendant the rotating axis can be moved in Cartesian mode, using the 7+
and 7- keys and it is not possible to enable or disenable the column integration in real
time.

17.8.2.1 Definition of the reference system


The integrated column base reference system (defined by variable $BASE) is defined
according to the following conventions (see Fig. 17.13):
– The origin of the column base reference system (Obase) lays on the bearing surface
(typically the floor);
– the Zbase axis is perpendicular to the bearing surface and in upward direction;
– the Xbase axis lays on the resting surface and is oriented in the direction of the robot
cantilever in calibration position (see Fig. 17.13);
– the Ybase axis consequently results with the direction indicated in Fig. 17.13.
On the cantilever (lever) there is the mounting flange of the robot base that can be
arranged in two positions only: either hanging on the lever (see Fig. 17.13) or resting on
the lever (robot standing). Therefore the robot base has to be always perpendicular to
the column rotating axis.
Vice-versa 4 robot base orientation positions are allowed (at 90° intervals) in relation to
the column base, and also the positive rotation direction can be selected at will.

Fig. 17.13 - Definition of the reference system

1 - column rotation 2 - column base reference 3 - robot base X b, Yb, Zb = Xbase, Ybase, Zbase

hs-0-0-mot_04.fm
00/0210 201
Use of Positioners managed by C5G

17.8.2.2 Calibration
The column calibration position is determined half way along the useful stroke and
marked by a zero notch. As this is an integrated axis it is not treated as a positioner of
the part to be machined and therefore it is not necessary to find points P1, P2 and P3
described in the Chap. TO_SET Program - Tool handling.

17.8.2.3 Kinematic description


The parameters needed for the column correct kinematic description are indicated in
Fig. 17.14.
It is also necessary to calculate the rotation speed to be attributed to the column being
programmed, so that the maximum tangential speed does not exceed the value of 250
mm/s (see standard in force). Therefore, first of all radius r has to be measured with
maximum robot extension, complete with tool mounted on the flange, as indicated in
Fig. 17.14. Next, the configuration software, on the Teach Pendant, calculates the
manual mode speed value.

Fig. 17.14- Parameters for the kinematic description of the integrated


column - 1

1 - column right-hand rotation R = column radius H = column height X b, Yb, Zb = Xbase , Ybase, Zbase

The axis is right-hand: if it is not, change the sign of the transmission ratio.

A table follows, summarising the useful mechanical data, taking into account that it is
mandatory that the integrated column is handled with auxiliary axis 7.

OPTION AXIS VALUE


(7) Axis length [mm] 7 R
(13) Axis type 7 ROTATING
(15) Axis offset [mm] 7 H
(18) Program speed override 7 X

Besides the R and H geometrical data indicated above, for the complete kinematic
description of the integrated column, the following Boolean data also has to be defined :
– an UpDown bit that indicates whether the robot is placed facing upward (TRUE) or
if it is overturned (FALSE) (as in Fig. 17.14);
– two Boolean values that indicate how the robot base is oriented in relation to the
column base (this convention has been kept identical to that required for the
integrated slide, to have compatibility); in particular the convention is as follows

hs-0-0-mot_04.fm
202 00/0210
Use of Positioners managed by C5G

(see Fig. 17.15):


• 180° rotation - Xrobot_base in opposite direction to Xcolumn_base ;
• 0° rotation - Xrobot_base in the direction of Xcolumn_base ;
• 270°rotation - Xrobot_base in opposite direction to Ycolumn_base ;
• 90°rotation - Xrobot_base in the direction of Ycolumn_base ;

Fig. 17.15 - Parameters for the kinematic description of the integrated


column - 2

Xbc , Ybc = Xcolumn_base , Ycolumn_base Xbr, Ybr = Xrobot_base Yrobot_base

17.8.3 Three linear axes portal


The current section describes the configuration of a robot mounted on a portal
composed by three integrated linear auxiliary axes.
Integrated motion means that the TCP position calculation takes into account the portal
position (thus the three X, Y and Z axes positions) besides the robot configuration; this
implies that the portal is integrated in the direct kinematic of the axes system. This
configuration causes the following effects:
– the cartesian positions (POSITION) are defined inside the cell area, independently
of the position of the portal axes, so even if the portal axes only are moved, the
cartesian position is anyway modified;
– jogging (JOG) the portal axes in a cartesian reference system (e.g. BASE
referenced JOG), the TCP position is not modified, due to the robot axes
movements which compensate the portal motion.

From the Teach Pendant, the linear axes can be moved in cartesian mode, using AUX
A - AUX B keys (by selecting the desired axes two-by-two).
It is also allowed to move the portal by means of the JPAD keys, where each couple of
keys allows to move one of the portal axes.
For further information related to AUX A - AUX B and JPAD keys, please refer to C5G
Control Unit Use manual - par. Black Keys - Chap. Use of the Teach Pendant

17.8.3.1 Definition of the reference system


The base reference system of the Integrated 3 linear axes Portal is defined according to
the following conventions (see Fig. 17.16):

hs-0-0-mot_04.fm
00/0210 203
Use of Positioners managed by C5G

– the origin of the reference system of the Portal Base (Obase) lays on the bearing
surface;
– Zbase axis is perpendicular to the bearing surface, exiting from it and oriented
according to the Z axis positive stroke;
– Xbase lays on the bearing surface and is oriented according to the X axis positive
stroke;
– Ybase consequently results.
The mounting flange of the robot base is on the portal.
It is possible to configure the mounting angle of the robot base.
It is also possible to configure the axis type (X, Y e Z) for each one of the three portal
axes (please note that the first one must be axis 7 and the next axes are in sequence).

Fig. 17.16- Definition of the reference systems

17.8.3.2 Calibration
The calibration position of the Portal, is usually defined close to the negative stroke of
each auxiliary axis, marked with a zero notch.

17.8.3.3 Kinematic description


The parameters needed for the 3 linear axes Portal kinematic description are indicated
in Fig. 17.7. Then, the configuration software available on the Teach Pendant calculates
the manual mode speed value.

To configure the 3 linear axes Portal, please also refer to the C5G Control Unit Use
manual, par. AUX_AXES .

hs-0-0-mot_04.fm
204 00/0210
Use of Positioners managed by C5G

A table follows, summarising the useful mechanical data, taking into account that it is
mandatory that the first axis of the Portal is number 7 and the next ones are in
sequence.

OPTION AXIS VALUE


Axis length [mm] 7 L1
Axis type [Tras/Rot] 7 TRANSLATING
Axis offset [mm] 7 H
Axis type [Coord] 7 [X,Y,Z]
Axis length [mm] 8 L2
Axis type [Tras/Rot] 8 TRANSLATING
Axis type [Coord] 8 [X,Y,Z]
Axis length [mm] 9 L3
Axis type [Tras/Rot] 9 TRANSLATING
Axis type [Coord] 9 [X,Y,Z]

Fig. 17.17 - Parameters for the kinematic description of the 3 linear axes
Portal

Besides the geometrical data indicated above, for the complete kinematic description of
the 3 linear axes Portal, also the assembly angle of the robot base on the portal flange
is to be defined.

17.8.4 Two linear axes Portal


The current section describes the configuration of a robot mounted on a portal
composed by two integrated linear auxiliary axes.
Integrated motion means that the TCP position calculation takes into account the portal
position (thus the two XY, XZ and YZ axes positions) besides the robot configuration;
this implies that the portal is integrated in the direct kinematic of the axes system.

hs-0-0-mot_04.fm
00/0210 205
Use of Positioners managed by C5G

This configuration causes the following effects:


– the cartesian positions (POSITION) are defined inside the cell area, independently
of the position of the portal axes, so even if the portal axes only are moved, the
cartesian position is anyway modified;
– jogging (JOG) the portal axes in a cartesian reference system (e.g. BASE
referenced JOG), the TCP position is not modified, due to the robot axes
movements which compensate the portal motion.

From the Teach Pendant, the linear axes can be moved in cartesian mode, using AUX
A - AUX B keys (by selecting the desired axes two-by-two).
For further information related to AUX A - AUX B and JPAD keys, please refer to C5G
Control Unit Use manual - par. Black Keys - Chap. Use of the Teach Pendant

17.8.4.1 Definition of the reference system


The base reference system of the Integrated 2 linear axes Portal is defined according to
the following conventions (see Fig. 17.18):
– the origin of the reference system of the Portal Base (Obase) lays on the bearing
surface;
– Zbase axis is perpendicular to the bearing surface, exiting from it and oriented
according to the Z axis positive stroke;
– Ybase lays on the bearing surface and is oriented according to the Y axis positive
stroke;
– Xbase consequently results.
The mounting flange of the robot base is on the portal. It is possible to configure the
mounting angle of the robot base.
It is also possible to configure the axis type (X, Y e Z) for each one of the two Portal axes
(please note that the first one must be axis 7 and the next one is in sequence).

Fig. 17.18- Definition of the reference system

17.8.4.2 Calibration
The calibration position of the Portal, is usually defined close to the negative stroke of
each auxiliary axis, marked with a zero notch.

hs-0-0-mot_04.fm
206 00/0210
Use of Positioners managed by C5G

17.8.4.3 Kinematic description

To configure the 2 linear axes Portal, please also refer to the C5G Control Unit Use
manual, par. AUX_AXES .

The parameters needed for the 2 linear axes Portal kinematic description are indicated
in Fig. 17.19.
Then, the configuration software available on the Teach Pendant calculates the manual
mode speed value.
A table follows, summarising the useful mechanical data, taking into account that it is
mandatory that the first axis of the Portal is number 7 and the next one is in sequence.

OPTION AXIS VALUE


Axis length [mm] 7 L1
Axis type [Tras/Rot] 7 TRANSLATING
Axis offset [mm] 7 H
Axis type [Coord] 7 [X,Y,Z]
Axis length [mm] 8 L2
Axis type [Tras/Rot] 8 TRANSLATING
Axis type [Coord] 8 [X,Y,Z]

Fig. 17.19 - Parameters for the kinematic description of the 2 linear axes
Portal

Besides the geometrical data indicated above, for the complete kinematic description of
the 2 linear axes Portal, also the assembly angle of the robot base on the Portal flange
is to be defined.

17.8.5 Integrated trans-rotational Column


The current section describes the configuration of a robot bearing on or hanging from a
lever on the rotating column, handled by an auxiliary axis which is, in turn, bearing on a
linear rail handled by a second auxiliary axis.
Integrated motion means that the TCP position calculation takes into account both the

hs-0-0-mot_04.fm
00/0210 207
Use of Positioners managed by C5G

column position and the position of the rail the column is bearing on, besides the robot
configuration; this implies that the trans-rotational column is integrated in the direct
kinematic of the axes system.
This configuration causes the following effects:
– the cartesian positions (POSITION) are defined inside the cell area, independently
of the position of both the column axis and the rail axis, so even if the column axis
only is moved, the cartesian position is anyway modified;
– jogging (JOG) the column axis in a cartesian reference system (e.g. BASE
referenced JOG), the TCP position is not modified, due to the robot axes
movements which compensate the column motion.

From the Teach Pendant, the rotational axis and the translational one of the rail, can be
moved in cartesian mode, using AUX A - AUX B keys.
For further information related to AUX A - AUX B and JPAD keys, please refer to C5G
Control Unit Use manual - par.Black Keys - Chap. Use of the Teach Pendant

17.8.5.1 Definition of the reference system


The base reference system of the Trans-rotational Column is defined according to the
following conventions (see Fig. 17.20):
– the origin of the reference system of the trans-rotational Column Base (Obase) lays
on the bearing surface (which usually is the floor);
– Zbase axis is perpendicular to the bearing surface, exiting from it and oriented
upwards;
– Xbase lays on the bearing surface and is oriented according to the rail axis positive
stroke;
– Ybase consequently results, having the direction shown in Fig. 17.20.
On the cantilever (lever) there is the mounting flange of the robot base that can be
arranged in two positions only: either hanging on the lever (see Fig. 17.20) or bearing
on the lever (robot standing). Therefore the robot base has to be always perpendicular
to the column rotating axis.
Vice-versa 4 robot base orientation positions are allowed (at 90° intervals) in relation to
the column base. Furthermore, it is also allowed to select the mounting angle of the
column base on the rail flange ( angle shown in Fig. 17.21), as well as the offset
between the rail flange and the column base (H1 in Fig. 17.21).

hs-0-0-mot_04.fm
208 00/0210
Use of Positioners managed by C5G

Fig. 17.20 - Definition of the reference system

17.8.5.2 Calibration
The Column calibration position is defined at mid-stroke, marked with a zero notch; the
Rail calibration position is usually defined close to the negative stroke of the auxiliary
axis, marked with its zero notch.

17.8.5.3 Kinematic description


The parameters needed for the Integrated trans-rotational Column complete kinematic
description are indicated in Fig. 17.21.
It is also necessary to calculate the rotational speed to be set for the Column while in
PROGR mode, so that the maximum tangential speed does not exceed the value of
250 mm/s (see standard in force). Therefore, first of all radius r has to be measured with
maximum robot extension, equipped with the tool mounted on the flange, as indicated
in Fig. 17.21.
Then, the configuration software available on the Teach Pendant calculates the manual
mode speed value.

To configure the Trans-rotational Column, please also refer to the C5G Control Unit Use
manual, par. AUX_AXES .

A table follows, summarising the useful mechanical data, taking into account that it is
mandatory that the first axis of the Integrated trans-rotational Column is number 7 and
it is the linear axis of the Rail (the translating axis).

OPTION AXIS VALUE


Axis length [mm] 7 L
Axis type [Tras/Rot] 7 TRANSLATING

hs-0-0-mot_04.fm
00/0210 209
Use of Positioners managed by C5G

OPTION AXIS VALUE


Axis offset [mm] 7 H1
Axis length [mm] 8 R
Axis type [Tras/Rot] 8 ROTATIONAL
Axis offset [mm] 8 H2

Fig. 17.21- Parameters for the kinematic description of the Integrated


Trans-rotational Column

Besides the geometrical data indicated above (H2 to describe the Column height and R
to describe its Radius), for the complete kinematic description of theTrans-rotational
Column, also the following parameters have to be defined:
– an UpDown bit that indicates whether the robot is placed facing upward (TRUE) or
if it is overturned (FALSE);
– a Robot Mounting Angle value that indicates how the Robot base is oriented in
relation to the Column base; in particular the convention is as follows:
• 180° rotation - Xrobot_base in opposite direction to Xcolumn_base ;
• 0° rotation - Xrobot_base in the direction of Xcolumn_base ;
• 270°rotation - Xrobot_base in opposite direction to Ycolumn_base ;
• 90°rotation - Xrobot_base in the direction of Ycolumn_base .

hs-0-0-mot_04.fm
210 00/0210
TO_SET Program - Tool handling

18. TO_SET PROGRAM - TOOL HANDLING

18.1 Introduction
TO_SET is an environment to calculate the positioner $TOOL, $UFRAME, $AUX_BASE
values, in a guided and automatic manner. It is also used to activate and execute the
Payload identification (optional function) procedure.
The most important characteristics are the following:
– It is completely organized in menus, and drives the operator to perform the required
steps; it also displays error messages or simple "warnings"
– All the messages are in the chosen language: when called up, TO_SET assumes
the language that is currently set in the C5G Control Unit.
– It uses the Teach Pendant with dedicated screen pages only.
This chapter contains detailed information about the following subjects:
– TO_SET Activation
– First screen page of TO_SET
– TOOL automatic calculation
– UFRAME automatic calculation
– BASE automatic calculation for POSITIONERS (optional)
– Payload identification (optional function)

18.2 Activation

TO_SET program is always present in the Controller Unit

To use it, select Setup page on the Teach Pendant and choose ToolFrame (Fig. 18.1).

Fig. 18.1 - Access to TO_SET program

HS-0-C5E-USO_44.fm
08/1012 211
TO_SET Program - Tool handling

If it is necessary to install TO_SET again, proceed in the following way:

a. select the Setup page and choose Install (FUI) command

b. select the device on which the TO_SET files are present

c. select TO_SET program

d. press ENTER to confirm.

HS-0-C5E-USO_44.fm
212 08/1012
TO_SET Program - Tool handling

18.3 First screen page of TO_SET


In Fig. 18.2, the MAIN MENU is displayed.
TO_SET is displayed in this way, as soon as it is activated.

Fig. 18.2 - Screen page 0.0

The screen page contains the following information:

TO_SET 003 program name + version number


Ov:100 the value of $GEN_OVR
Ar: 1 the number of the selected ARM
Ty: Jnt type of selected movement

Using F1..F6 function keys, one of the displayed items can be selected:
TOOL (F1): TOOL automatic calculation
UFRAME (F2): UFRAME automatic calculation
POSITIONER (F3): Base automatic calculation for POSITIONERS
PAYLOAD IDENTIFICATION (F4): Payload characteristics Identification
Exit TO_SET (F6): end of TO_SET program

The following detailed description illustrates the available procedures, specifically:


– TOOL automatic calculation
– UFRAME automatic calculation
– BASE automatic calculation for POSITIONERS (optional)
– Payload identification (optional function)

Note that whenever the User saves the calculated value, it is saved in the corresponding
Data Page table.

HS-0-C5E-USO_44.fm
08/1012 213
TO_SET Program - Tool handling

18.4 TOOL automatic calculation


Press F1 in TO_SET main menu (see Fig. 18.2) to enter it.
In this environment it is possible to define the dimensions of the work tool mounted on
the robot flange. The precision of the calculation is the same as the robot, used as a
measuring instrument.
Detailed information is given on the following:
– Needed Tools
– General characteristics
– Procedure

18.4.1 Needed Tools


– Calibrated tool (Tool Master)
– Reference point (or master cube)

18.4.1.1 Calibrated tool (Tool Master)


This is a calibrated tool with known X, Y, Z measurements that will be mounted on the
robot flange for the acquisition of the reference position. As an alternative an identified
point on the work tool can be used, for which the distance from the robot flange centre
must be known and precise.
Taking as an example a Smart NJ 110-3.0 o NJ 130-2.6, the calibrated tool may be :
measurement: 117 [mm]
In this case the calibrated tool is to be mounted on the robot flange in X_tool direction
and the values to be declared are : X=190, Y=0, Z=-8.

Fig. 18.3 - SMART NJ 110-3.0 o NJ 130-2.6 - Calibrated tool

For any further information about the calibrated tool, see the Robot Technical
Specifications Manual.

HS-0-C5E-USO_44.fm
214 08/1012
TO_SET Program - Tool handling

18.4.1.2 Reference point (or master cube)


It is very important to identify a physical reference point in the environment surrounding
the robot, so as to bring the robot TCP on to this point: once with the Tool Master then
with the measuring tool. For this purpose a MASTER CUBE has been designed with a
mobile tip that when fixed in zero position can be used as the REFERENCE POINT.
The cube (or any other point taken as reference) MUST BE IN A FIXED AND STABLE
POSITION, easily accessible by the robot and positioned on the FLOOR (if the robot is
on the floor), on the WALL (if the robot is on the wall), on the CEILING (if the robot is
suspended from the ceiling).

18.4.2 General characteristics


– The TOOL MASTER can be mounted in Z_tool or in X_tool.
Position B is made possible by a threaded precision hole on the robot flange. In
this way it is possible to have the measuring tool mounted on the flange and at the
same time the tool master screwed on the flange in X_tool direction.
– Possibility to calculate the tool with the robot on the FLOOR, on the WALL or
hanging from the CEILING , taking care to position the cube (or any other point
taken as reference) on the FLOOR ( if the robot is on the floor), on the WALL (if the
robot is on the wall), on the CEILING (if the robot is suspended from the ceiling).
– All the robot positions on the reference, whether with tool master or with measuring
tool, are not rigid: the operator can position the TCP on the reference as desired,
according to requirements.
– Possibility to calculate the tool relocation as to the robot flange centre (X, Y, Z
Tool) with three reset Euler angles (orientation nil).
– Possibility to calculate (besides X, Y, Z Tool) also the rotations around X_tool and
Y_tool (<A>: Euler 1 and <E>: Euler 2) so as to fix the new Z_tool on the tool, in
the required direction and sense (see also Tool orientation calculation).
– Possibility to calculate (besides X, Y, Z, A, E Tool) also the rotation around the new
Z_tool (<R>: Euler 3), so as to fix for a certain "tool plane" the direction and
sense of the X_tool and Y_Tool , rotating around the new Z_tool (see also
Tool orientation calculation).
Detailed descriptions are given below, dealing with the following subjects:
– Tool orientation calculation
– How to identify the "dummy reference system"

18.4.2.1 Tool orientation calculation


After calculating the dimensions of the tool to be measured (X, Y, Z Tool), with TO_SET
an orientation (A, E, R Tool) can also be fixed to the new TCP
To fix the orientation on the new TCP a known reference system is necessary.
TO_SET has defined this reference system on the "reference point" .
The "dummy reference system" is created by TO_SET when the robot is brought on to
the "reference point" with TOOL MASTER (Complete procedure ) and will be assumed
by the new TCP every time the robot is brought to the "reference point" with "TOOL
TO BE MEASURED" to calculate the orientation.

HS-0-C5E-USO_44.fm
08/1012 215
TO_SET Program - Tool handling

18.4.2.2 How to identify the "dummy reference system"


It is advised (with values of $BASE = 0) to make positive and negative movements in
BASE for axis 1 (X_base), axis 2 (Y_base) and axis 3 (Z_base) .
Knowing that X_rifer = -X_base; Y_rifer = Y_base; Z_rifer = -Z_base, it is easy to identify
the direction and the sense of the "dummy reference system".
– Z_tool (calculation of <A>: Euler 1; <E> Euler 2). See Fig. 18.12 - Screen page
1.8.
To associate the new Z_tool to the new TCP , it is necessary to position the new
TCP (rotating the TOOL of axes 4 and 5) until the directions of the tool that is to
assume the new Z_tool coincide with the direction and sense of Z_rifer.
Example :
Supposing that the tool is a welding torch, to obtain the new Z_tool coming out
from the torch, the torch has to be brought in perpendicular to the reference
system (the same direction as Z_rifer), so that Z_rifer is assumed as Z_tool
coming out from the torch.
– X_tool and Y_tool (calculation <R>: Euler 3). See Fig. 18.13 - Screen page 1.9.
To associate the new X_tool and Y_tool to the new TCP of the tool, position the
new TCP (rotating in TOOL of axis 6) until the directions of the tool that is to
assume the new X_tool and Y_tool coincide with the direction and sense of
X_rifer and Y_rifer respectively.
Example:
Supposing that the tool is a welding torch, to obtain the new X_tool orientated
according to the "torch plane" identified between the torch and the mounting
bracket, this plane has to be oriented until it coincides with X_rifer direction, so
that X_rifer is assumed as X_tool, associated to the "torch plane". The same is
valid when referring to the Y_tool.

18.4.3 Procedure
To access the procedure, press key F1 in Fig. 18.2.
If the TOOL command is sent (pressing key F1) a second screen is shown that asks
the user to select either local tool or remote tool :

Fig. 18.4 - Screen page 1.0

Accepted commands:

HS-0-C5E-USO_44.fm
216 08/1012
TO_SET Program - Tool handling

F1: calculates LOCAL TOOL ; a second screen page is accessed


(Fig. 18.5 - Screen page 1.1) that asks the user to insert the
number of the tool to be measured or checked
F2: calculates REMOTE TOOL(see. par REMOTE TOOL Automatic
Calculation)
F6: returns to main menu (see Fig. 18.2)

Fig. 18.5 - Screen page 1.1

At this point the table that contains all the tools that already exist is scanned to check
which of these conditions applies:
– The entered tool number corresponds to an empty position in the table, therefore
the tool calculation proceeds with one of the available methods
(Fig. 18.6)
– The entered tool already exists in the table, therefore the measurement and the
method previously used for the calculation are displayed
(Fig. 18.7).
As can be seen, in the same file there may be tools calculated with the standard method
(without acquired positions) and tools calculated with the new procedure that also
associates the acquired positions to the tool measurement, it will therefore be the task
of the user to ascertain that the file tt_tool1.var in UD: is the correct one, containing the
tool to be checked.

Fig. 18.6 - Screen page 1.2

HS-0-C5E-USO_44.fm
08/1012 217
TO_SET Program - Tool handling

Accepted commands:

F1: executes Tool calculation with standard method - Complete


procedure; access given to screen page 1.4 (in Fig. 18.8)
F2: executes Tool verification with standard method - Partial
procedure; access given to screen page 1.6 (in Fig. 18.10)
F3: executes Tool Calculation with "4 points method" - Complete
procedure; access given to screen page 1.17 (in Fig. 18.21)
F6: returns to main menu (see Fig. 18.2)

If the Tool already exists in the table, Fig. 18.7 is shown.

Fig. 18.7 - Screen page 1.3

Accepted commands:

F1: tool verification; there are two possibilities:


• when the standard method is used access is given to partial procedure
screen page 1.6 (in Fig. 18.10),
• when the 4-points method is used , access is given to screen page 1.17
(in Fig. 18.21)
F2: executes a new calculation then returns to screen page 1.2 (in Fig. 18.6)
F6: returns to main menu (see Fig. 18.2)

The following description gives details of each possible procedure for the Local Tool :
– Tool calculation with standard method - Complete procedure
– Tool Calculation with "4 points method" - Complete procedure
– Tool verification with standard method - Partial procedure

18.4.4 Tool calculation with standard method - Complete


procedure
The procedure is accessed by pressing F1, Fig. 18.6.
When to execute the procedure:

HS-0-C5E-USO_44.fm
218 08/1012
TO_SET Program - Tool handling

– If it is the very first time that an automatic calculation of the tool is executed;
– If the reference point or the robot has been moved;
– If the robot has been recalibrated.

The complete procedure can be used to store in UD: the scan result position and the
declared tool master values in TO_SET.VAR.
This procedure only has to be executed once. All the subsequent calculations of a tool
mounted on the robot flange will only require the Partial procedure
(F2 from screen page 1.2 of Fig. 18.6).

Fig. 18.8 - Screen page 1.4

Draws the operator’s attention to the Tool Master measurements. It displays them and
allows modification, if necessary.
Accepted commands:

F1: continues the procedure (see Fig. 18.9)


F2: changes tool master values (see Fig. 18.17)
F6: returns to main menu (see Fig. 18.2)

Fig. 18.9 - Screen page 1.5

Asks to take the TCP in the Tool Master on the reference, with the relevant
measurements correctly defined (Fig. 18.8).The robot may be in any position: the

HS-0-C5E-USO_44.fm
08/1012 219
TO_SET Program - Tool handling

operator can position the TCP on the reference as preferred, according to requirements.
At this moment it is advisable to move in TOOL of axes 4, 5, 6 to check the dimensions
of the tool master and the robot calibration.
Accepted commands:

F1: to be pressed when the robot is on the point; continues


procedure (Fig. 18.10)
F6: returns to main menu (Fig. 18.2)

18.4.5 Tool verification with standard method - Partial procedure


To have access to this procedure press F1 from Fig. 18.7 or F3 from Fig. 18.6.
When to execute:

Only if the Complete procedure has been executed at least once.

With the partial procedure the measurements of the tool mounted on the robot flange
can be calculated. It is only possible to calculate the relocations (X,Y,Z); or continue in
the calculation of the rotations (<A>: Euler 1; <E>: Euler 2) and lastly it is possible to
calculate the rotation around the new Z- tool (<R>: Euler 3).

Fig. 18.10- Screen page 1.6

Asks to bring the TCP of the tool to be measured on the reference point.
The robot may be in any position: the operator can position the TCP on the reference as
preferred, according to requirements.
Accepted commands:

F1: to be pressed when the robot is on the point; continues procedure


(Fig. 18.11)
F6: returns to main menu (Fig. 18.2)

HS-0-C5E-USO_44.fm
220 08/1012
TO_SET Program - Tool handling

Fig. 18.11 - Screen page 1.7

Displays the $TOOL calculated values (XYZ relocations and AER orientations).
It is then possible to move axes 4,5,6 in TOOL to check that the new TCP does not move
on the reference (movements of approx. 3 millimetres are accepted).
If this is not so, check:
– robot calibration,
– tool master dimensions declared in the Complete procedure,
– position of the reference point (not changed as to the Complete procedure ).
After checking, repeat the procedure (Complete or Partial).
Accepted commands:

F1: continues the procedure (Fig. 18.12)


F2: saves calculated values (Fig. 18.16 or remains Fig. 18.11)
F3: repeats procedure: (returns to Fig. 18.10)
F6: returns to main menu (Fig. 18.2).

Fig. 18.12 - Screen page 1.8

See paragraph on Tool orientation calculation.

HS-0-C5E-USO_44.fm
08/1012 221
TO_SET Program - Tool handling

The operator has to position the Z_TOOL (positive sense ) of the tool parallel to a drive
shaft of the robot BASE. To choose the required direction just press one of the function
keys (F2..F4) and then F1 to accept the measurement.
If the tool axes are parallel to the flange reference frame ($TOOL(0)), it is best to bring
the robot to calibration position; the advantage of this operation is that it brings all three
tool axes parallel to those of the BASE with no further movements of the robot. To
complete the orientation calculation the operator only has to use the appropriate
function keys to select to which BASE drive shafts the Z_TOOL and then the X_TOOL
are parallel.
Check that the new orientation is that actually wished for, and if necessary repeat the
procedure (F3 from screen page 1.9 in Fig. 18.13).
Accepted commands:

F1: to be pressed when orientation has been completed; continues


procedure (Fig. 18.13)
F2: directs the Z_TOOL in relation to +X_BASE or -X_BASE
F3: directs the Z_TOOL in relation to +Y_BASE or -Y_BASE
F4: directs the Z_TOOL in relation to +Z_BASE or -Z_BASE
F6: returns to main menu (Fig. 18.2).

Fig. 18.13- Screen page 1.9

Displays the $TOOL calculated values (XYZ relocations and AER orientations).
Accepted commands:

F1: continues the procedure (Fig. 18.14)


F2: saves calculated values (Fig. 18.16 or remains in Fig. 18.13)
F3: repeats the procedure; (returns to Fig. 18.12)
F6: returns to main menu (Fig. 18.2).

HS-0-C5E-USO_44.fm
222 08/1012
TO_SET Program - Tool handling

Fig. 18.14 - Screen page 1.10

The operator has to direct the X_TOOL (positive sense) of the tool parallel to one of the
drive shafts of the robot BASE (the axis selected in the previous step is no longer
available). To choose the desired direction just press one of the function keys (F2..F5)
and then F1.
Check that the new orientation is that actually required, and if necessary repeat the
procedure (F3 from screen page 1.11 in Fig. 18.15).
Accepted commands:

F1: to be pressed when orientation has been completed; continues


procedure (Fig. 18.13)
F2: directs the X_TOOL in relation to +X_BASE
F3: directs the X_TOOL in relation to -X_BASE
F4: directs the X_TOOL in relation to +Y_BASE
F5: directs the X_TOOL in relation to -Y_BASE
F6: returns to main menu (Fig. 18.2 - Screen page 0.0).

Fig. 18.15 - Screen page 1.11

Displays the $TOOL calculated values (XYZ relocations and AER orientations).
Accepted commands:

HS-0-C5E-USO_44.fm
08/1012 223
TO_SET Program - Tool handling

F1: returns to Fig. 18.6


F2: saves calculated values (Fig. 18.16 or remains in Fig. 18.15)
F3: repeats the procedure (returns to Fig. 18.14)
F6: returns to main menu (Fig. 18.2).

After every Save operation, if there are already Euler angles in the table, the following
screen page is displayed:

Fig. 18.16- Screen page 1.12

This displays the $TOOL calculated values (XYZ relocations and AER orientations) and
warns that there are already Euler angles in the table. It is asked if they are to be kept
(F1) or to be overwritten with the new values (F2). This makes it possible to keep the
Euler angles if it is only required to recalculate the tool relocations.
Fig. 18.17 displays the TOOL MASTER values (XYZ relocations) and allows their
modification.

Fig. 18.17- Screen page 1.13

Accepted commands:

esc: to omit the insertion of each separate value

The screen page in Fig. 18.18 - Screen page 1.14 displays whether a Partial procedure
has been requested without ever having executed a Complete procedure. This means

HS-0-C5E-USO_44.fm
224 08/1012
TO_SET Program - Tool handling

that the master reference position is missing (check TO_SET.VAR).


If the answer is OK, the system returns to the screen page shown in Fig. 18.9.

Fig. 18.18 - Screen page 1.14

Accepted commands:

F1: returns to Fig. 18.6


F6: returns to main menu (Fig. 18.2)

The screen page in Fig. 18.19 displays whether the SAVE procedure for the calculated
values has been omitted.

Fig. 18.19 - Screen page 1.15

Accepted commands:

F1: repeats Save


F6: returns to main menu (Fig. 18.2)

18.4.6 Tool Calculation with "4 points method" - Complete


procedure
To access this procedure, press key F3 of screen page 1.2 in Fig. 18.6.

HS-0-C5E-USO_44.fm
08/1012 225
TO_SET Program - Tool handling

This procedure brings the TCP to a visible reference point within the robot working
space, with at least three different orientations and acquires the relevant positions
(see Fig. 18.20).

Fig. 18.20- Points acquisition

1. acquisition point 3
2. acquisition point 2
3. acquisition point 1
4. reference

Follow these steps:

a. Move the TCP to the reference point

b. Teach point 1

c. Move the TCP back to the reference point with a sufficiently different orientation as
to the previous point

d. Teach point 2

e. Execute steps c. and d. again to acquire point 3

f. If the TCP measurement is possible, the user is given an evaluation of the


acquisition procedure accuracy (and not the tool measurement precision) with the
possibility to accept the measurement supplied and continue with the orientation
calculation (step j.) or to continue with the acquisition of points with the possibility
to move the robot in Tool mode (step g.)

g. Move the TCP back to the reference point with a sufficiently different orientation as
to the previous points

h. Teach the new point (max. 8 points )

i. Execute step f. again

j. End of points acquisition: it is possible to continue with the orientation calculation,


repeat the calculation of X, Y and Z, return to main menu.
As from the acquisition of point 3, the tool calculation algorithm is sent, since if the
acquired points are independently linear, the three X, Y and Z coordinates are obtained
in output that permit the definition of the TCP.
As mentioned in the procedure description, together with the TCP measurement, the

HS-0-C5E-USO_44.fm
226 08/1012
TO_SET Program - Tool handling

user is given an evaluation of the acquisition procedure accuracy (this assesses the
standard deviation, acquired points dispersion index). The two evaluation classes may
be: imprecise measure and good measure. If the measurement is imprecise it is
necessary to continue with the acquisition of a new point, whereas the procedure is
considered completed when the measurement is good. If the acquisition of the eighth
point is reached without obtaining a good measurement of the tool, the procedure has
to be repeated from the start.
Continuing with the description of the user interface, once the tool calculation
environment is entered with the 4 points method, the following screen page is displayed:

Fig. 18.21 - Screen page 1.17

The user moves the TCP to the reference point and confirms the acquisition by pressing
F1 key on the Teach Pendant.
It is possible to interrupt the tool calculation at any time and to return to the main menu
by pressing F6 key.
For the acquisition of the next points the screen page is the same as the previous one.
As soon as a first tool measurement is ready, a screen page is shown to inform the user
that as from this moment it is possible to move in TOOL reference.
Continuing, the following situations may take place:
– If the calculation algorithm returns an imprecise tool measurement the following
screen page is shown (Fig. 18.22):

Fig. 18.22 - Screen page 1.19a

Accepted commands:

HS-0-C5E-USO_44.fm
08/1012 227
TO_SET Program - Tool handling

F1: continues to acquire a new point (Fig. 18.21)


accepts the calculated tool and continues according to the mode
described in Fig. 18.11 (the calculation procedure for the Euler
F2:
angles remains unchanged), bearing in mind that the calculated
tool is not precise!

– If the calculation algorithm returns a tool good measurement the following screen
page is shown (Fig. 18.23):

Fig. 18.23- Screen page 1.19b

If F1 is pressed, the calculated TCP coordinates are displayed and from this point
onwards the user proceeds according to the modes described in Fig. 18.11.
– If the user has acquired 8 points and the algorithm has not been able to calculate
the tool, even with an imprecise measurement, this means that the acquired points
are imprecise or are dependently linear
(see Fig. 18.24).
The more diversified the orientation of the acquired points, the better the results!

Fig. 18.24- Screen page 1.19c

Accepted commands:

F1: repeats the calculation (see Fig. 18.21)


F2: returns to main menu (Fig. 18.2)

HS-0-C5E-USO_44.fm
228 08/1012
TO_SET Program - Tool handling

18.4.6.1 Local Tool verification with "4 points method"


This is accessed by pressing F1 key (Fig. 18.7), Tool Verification.
This option is used to repeat a tool measurement that has already been executed and
saved in file tt_tool1.var. If the method used previously was the standard method, the
partial procedure of this method is followed (Fig. 18.10), whereas if the 4 points method
was used, a procedure is followed that is very similar to that already described for a new
calculation of the tool, with the additional possibility to move the reference on the remote
TCP with MOVE commands to the position stored together with the tool measurement.
In this way the measurement repeatability is improved since the tool verification is
executed acquiring the points with the same orientation (with a very slight
approximation) as those of the previous acquisition.

Fig. 18.25 - Screen page 1.20

When the START key is pressed (with control in Drive On) the reference moves toward
the first stored position associated to that tool; the Start can be released at any time to
manually adjust the reference approach to the TCP to be measured in Jog, and to
resume the movement toward the position by pressing the START key again.
Accepted commands:

F1: If the move is reached and the position is OK, press F1


If it is wished to force termination of the Move (either because the
TCP has already been reached or because it is considered better
F2:
to position the reference on the TCP with movements in Jog),
press F2
F6: returns to main menu (Fig. 18.2)

Be sure that the movement is executed at the speed indicated on the Teach Pendant!

After the Move has terminated (either naturally or forced by the user) pass to the next
acquisition following the same procedure as described for the first point. If instead it is
chosen to return to the first menu, press F6.
Once the algorithm is able to calculate a tool, a screen page is displayed informing the
user that as from that moment it is possible to move in TOOL reference.

HS-0-C5E-USO_44.fm
08/1012 229
TO_SET Program - Tool handling

18.4.7 REMOTE TOOL Automatic Calculation


This can be accessed by pressing F2 key from the screen page in Fig. 18.4, i.e. from
the main menu of the tool calculation. In this environment the coordinates system of a
fixed tool (remote tool) can be defined using the robot as measuring system.
Detailed information is given for the following subjects:
– Tools needed
– General characteristics

18.4.7.1 Tools needed

18.4.7.1.1 Tool with known dimensions mounted on Robot Flange


A reference tool must be mounted on the flange that has known dimensions declared in
the $TOOL system variable.
The coordinates will be indicated as X_rif, Y_rif and Z_rif.
It is advised to use the TOOL MASTER or CALIBRATED TOOL that was used for the
Tool automatic calculation (see paragraph TOOL automatic calculation). As an
alternative an identified tip on the work tool can be used that has a distance from the
robot flange centre that is known and precise.

18.4.7.2 General characteristics


In case of TOOL_RMT command (pressing F2 key) the procedure is the same as the
Tool calculation (F1).
Whereas for the tool the reference is the robot BASE, for the remote tool it is necessary
to define the X, Y and Z references of the tool fixed on the robot flange, indicated as Xrif,
Yrif and Zrif.
At the end of the procedure, before returning to the main menu(Fig. 18.2), the user is
asked whether the remote tool is to be kept enabled (Fig. 18.26)

Fig. 18.26- Screen page 2.1

If F1 is pressed, the Remote Tool remains enabled, if F2 is pressed the start situation is
resumed.

HS-0-C5E-USO_44.fm
230 08/1012
TO_SET Program - Tool handling

18.5 UFRAME automatic calculation


This environment is entered by pressing key F2 from the main menu of TO_SET
(Fig. 18.2).
In this environment a new reference system can be defined in relation to which the
work positions will be taught. The precision of the calculation is the same as the robot,
used as a measuring tool.
Detailed information is given on these subjects:
– Needed Tools
– General characteristics
– Procedure

18.5.1 Needed Tools


The following topics are described:
– Tool with known dimensions mounted on Robot Flange
– 3 Reference Points (ORIGIN, Xpos and XYpos)

18.5.1.1 Tool with known dimensions mounted on Robot Flange


A tool must be mounted on the robot flange that has known dimensions declared in the
$TOOL system variable.
It is advised to use the TOOL MASTER or CALIBRATED TOOL that was used for the
TOOL automatic calculation. As an alternative an identified tip on the work tool can be
used that has a distance from the robot flange centre that is known and precise.

18.5.1.2 3 Reference Points (ORIGIN, Xpos and XYpos)


3 reference points have to be identified on the workpiece :
– ORIGIN: where the FRAME origin will be fixed;
– Xpos: X-frame direction and sense
– Xypos: Y-frame direction and sense
The direction and sense of the Z-frame are always considered outgoing upwards as to
the XY-frame plane.
The $UFRAME is always calculated in relation to the robot environment that coincides
with the origin of the robot base when $BASE=0

18.5.2 General characteristics


None of the robot positions on the 3 reference points are rigid: the operator can position
the TCP on the references as preferred, according to requirements.
At the end it is possible to save the Frame calculation in the TU_FRAME table
(see Fig. 18.33).

HS-0-C5E-USO_44.fm
08/1012 231
TO_SET Program - Tool handling

18.5.3 Procedure
If the UFRAME command is entered (pressing F1) access is obtained to a second
screen page (Fig. 18.27) that asks the User to select either LOCAL FRAME or REMOTE
FRAME:

Fig. 18.27- Screen page 3.0

Another screen page is then shown (Fig. 18.28):

Fig. 18.28- Screen page 3.1

This screen page (Fig. 18.28 - Screen page 3.1) shows the operator the values of the
currently declared $TOOL variable.
The values are referred to the tool mounted on the flange and that will be used for the
FRAME calculation. The values are displayed and they can be modified if necessary.
Accepted commands:

F1: continues procedure (Fig. 18.29)


F2: changes the $TOOL values (Fig. 18.34)
F6: returns to main menu (Fig. 18.2)

HS-0-C5E-USO_44.fm
232 08/1012
TO_SET Program - Tool handling

Fig. 18.29 - Screen page 3.2

Asks the operator to take the tool TCP on the ORIGIN point.
The robot may be in any position: the operator can position the TCP on the ORIGIN point
as preferred, according to requirements.
Accepted commands:

to be pressed when the robot is on point; continues procedure


F1:
(Fig. 18.30)
F6: returns to main menu (Fig. 18.2)

Fig. 18.30 - Screen page 3.3

Asks to move the tool TCP to the Xpos point.


The robot may be in any position: the operator can move the TCP to Xpos point as
preferred, according to requirements.
Accepted commands:

to be pressed when the robot is on point; continues procedure


F1:
(Fig. 18.31)
F6: returns to main menu (Fig. 18.2)

HS-0-C5E-USO_44.fm
08/1012 233
TO_SET Program - Tool handling

Fig. 18.31- Screen page 3.4

Asks the operator to take the tool TCP on the Xypos point.
The robot may be in any position: the operator can move the TCP to Xpos point as
preferred, according to requirements.
Accepted commands:

to be pressed when the robot is on point; continues procedure


F1:
(Fig. 18.32 o Fig. 18.36)
F6: returns to main menu (Fig. 18.2)

Fig. 18.32- Screen 3.5

The program displays the $UFRAME calculated values (XYZ relocations and AER
orientations).
At this time it is possible to move in Uframe mode (selected by Motion Page, COORD
menu - see C5G Control Unit Use) to check that the new origin is that desired. If it is
not so, check:
At this time it is possible to move in USR mode (selected by key [TYP] of TP) to check
that the new origin is that desired. If it is not so, check:
– Robot calibration;
– $TOOL values (referred to the tool mounted on the flange);
– the 3 reference points (check that the sequence required by TO_SET has been
followed)

HS-0-C5E-USO_44.fm
234 08/1012
TO_SET Program - Tool handling

Accepted commands:

F1: returns to screen page in Fig. 18.28


F2: saves calculated values (Fig. 18.33 or Fig. 18.36)
F6: returns to main menu (Fig. 18.2)

Fig. 18.33 - Screen page 3.6

The program displays the $UFRAME calculated values (XYZ relocations and AER
orientations).
The program allows to save the calculated values in the TU_FRAME table.

TU_FRAME is available in the System Software CD, in the Configuration Tools


directory.

Accepted commands:

to omit the SAVE request. In this case the screen page will be
<esc>:
displayed in (Fig. 18.35)

Fig. 18.34 - Screen page 3.7

Displays the $TOOL values currently declared (XYZ relocations and AER orientations)

HS-0-C5E-USO_44.fm
08/1012 235
TO_SET Program - Tool handling

and allows their modification.


Accepted commands:

esc: to omit the insertion of each separate value

Fig. 18.35- Screen page 3.8

Displayed if the SAVE procedure for the calculated values has been omitted.
Accepted commands:

F1: returns to screen page in Fig. 18.36


F6: returns to main menu (Fig. 18.2)

Fig. 18.36- Screen page 3.9

Displayed if it is not possible to execute the $UFRAME calculation.


Check:
– robot calibration;
– the $TOOL values (referred to the tool mounted on the flange);
– the 3 reference points (check that the sequence required by TO_SET has been
followed)
Accepted commands:

HS-0-C5E-USO_44.fm
236 08/1012
TO_SET Program - Tool handling

F1: returns to screen page in Fig. 18.28


F6: returns to main menu (Fig. 18.2)

18.5.4 REMOTE UFRAME automatic calculation


This environment is entered by pressing key F2 from the main menu of TO_SET
(Fig. 18.2). If a remote tool is declared, the part mounted on the robot flange becomes
the REMOTE UFRAME and has its own reference system. In this environment the new
reference system can be defined in relation to which the work positions will be learnt.
The precision of the calculation is the same as robot, used as measuring system.
Detailed information is given on these subjects:
– Needed Tools
– General characteristics
– Procedure

18.5.4.1 Needed Tools


The following topics are described:
– Tool with known dimensions mounted onto the Robot Flange
– 3 reference points (ORIGIN, Xpos and XYpos)

18.5.4.1.1 Tool with known dimensions mounted onto the Robot Flange
A tool must be mounted onto the robot flange that has known dimensions declared in
the $TOOL system variable.
It is advised to use the TOOL MASTER or CALIBRATED TOOL that was used for the
TOOL automatic calculation. As an alternative an identified tip on the work tool can be
used that has a distance from the robot flange centre that is known and precise.

18.5.4.1.2 3 reference points (ORIGIN, Xpos and XYpos)


3 reference points are to be identified on the workpiece:
– ORIGIN: where the FRAME origin is fixed;
– Xpos: determines the X-frame direction and sense
– Xypos: determines the Y-frame direction and sense
The direction and sense of the Z-frame are always considered outgoing upwards as to
the XY-frame plane.
$UFRAME is always calculated in relation to the robot environment that coincides with
the origin of the robot base when $BASE=0.

18.5.4.2 General characteristics


None of the robot positions on the 3 reference points are rigid: the operator can position
the TCP on the references as preferred, according to requirements.

HS-0-C5E-USO_44.fm
08/1012 237
TO_SET Program - Tool handling

It is allowed to save the frame calculation result, in the UFRAME table, in Data Page.

18.5.4.3 Procedure

Fig. 18.37- Screen page 4.1

Shows the operator the values of the currently declared $TOOL variable. The values are
referred to the tool mounted on the flange and that will be used for the FRAME
calculation. The values are displayed and they can be modified if necessary.

Be careful: the Remote Tool is enabled!

Accepted commands:

F1: continues procedure (Fig. 18.38)


F2: changes the $TOOL values (Fig. 18.43)
F6: returns to main menu (Fig. 18.2)

Fig. 18.38- Screen page 4.2

Asks to take the tool TCP on the ORIGIN point.


The robot may be in any position: the operator can move the TCP to the ORIGIN point

HS-0-C5E-USO_44.fm
238 08/1012
TO_SET Program - Tool handling

as preferred, according to requirements.


Accepted commands:

F1: to be pressed when the robot is on point; continues procedure (Fig. 18.39)
F6: returns to main menu (Fig. 18.2)

Fig. 18.39 - Screen page 4.3

Asks the operator to move the tool TCP to Xpos point. The robot may be in any position:
the operator can move the TCP to Xpos point as preferred, according to requirements.
Accepted commands:

F1: to be pressed when the robot is on point; continues procedure (Fig. 18.40)
F6: returns to main menu (Fig. 18.2)

Fig. 18.40 - Screen page 4.4

Asks the operator to move the tool TCP to XYpos point. The robot may be in any
position: the operator can move the TCP to XYpos point as preferred, according to
requirements.
Accepted commands:

to be pressed when the robot is on position; continues procedure


F1:
(Fig. 18.41 o Fig. 18.45)

HS-0-C5E-USO_44.fm
08/1012 239
TO_SET Program - Tool handling

F6: returns to main menu (Fig. 18.2)

Fig. 18.41- Screen page 4.5

Displays the $UFRAME calculated values (XYZ displacements and AER orientations).
At this time it is possible to move in UFRAME mode (selected by COORD key of the
Teach Pendant) to check that the new origin is the desired one. If not, check:
muovere in modalità UFRAME (selezione tramite tasto COORD del Terminale di
Programmazione)
– robot calibration;
– $TOOL values (referred to the tool mounted on the flange);
– the 3 reference points (check that the sequence required by TO_SET)
Accepted commands:

F1: returns to screen page in Fig. 18.37


F2: saves calculated values (Fig. 18.42 or screen page Fig. 18.46)
F6: returns to main menu (Fig. 18.2)

Fig. 18.42- Screen page 4.6

Displays the $UFRAME calculated values (XYZ displacements and AER orientations).
To save the calculated values in the TU_FRAME table.

HS-0-C5E-USO_44.fm
240 08/1012
TO_SET Program - Tool handling

TU_FRAME is contained in the system software CD, in the Configuration Tools


directory.

Accepted commands:

to omit the SAVE request. In this case the screen page will be
<esc>:
displayed in Fig. 18.44

Fig. 18.43 - Screen page 4.7

Displays the $TOOL values currently declared (XYZ displacements and AER
orientations) and allows the modification.
Accepted commands:

<esc>: to omit the insertion of each separate value

Fig. 18.44 - Screen page 4.8

Displayed if the SAVE procedure for the calculated values has been omitted.
Accepted commands:

HS-0-C5E-USO_44.fm
08/1012 241
TO_SET Program - Tool handling

F1: returns to screen page in Fig. 18.41


F6: returns to main menu (Fig. 18.2)

Fig. 18.45- Screen page 4.9

Displayed if it is not possible to execute the $UFRAME calculation.


Check:
– robot calculation;
– the $TOOL values (referred to the tool mounted on the flange);
– the 3 reference points (check that the sequence required by TO_SET has been
followed).
Accepted commands:

F1: returns to screen page in Fig. 18.37


F6: returns to main menu (Fig. 18.2)

Before returning to the main menu (Fig. 18.2) it is asked if the remote tool is to be kept
enabled (Fig. 18.46).

Fig. 18.46- Screen page 4.10

Press F1 to keep the remote tool enabled; press F2 to restore the start situation (the tool
is the one shown in Fig. 18.37).

HS-0-C5E-USO_44.fm
242 08/1012
TO_SET Program - Tool handling

18.6 BASE automatic calculation for POSITIONERS


(optional)
This environment is entered by pressing F3 from the TO_SET main menu (see Fig. 18.2
- Screen page 0.0). In this environment the reference system of a positioner can be
defined in relation to the robot, to obtain the cooperative movement between robot and
positioner.
The precision of the calculation is the same as for the robot, used as a measuring tool.
A detailed description is given below for:
– Tools required
– General characteristics

18.6.1 Tools required


A detailed description is given for the following topics:
– Tool of known dimensions mounted on the robot flange
– 3 reference points (P1, P2, P3)

18.6.1.1 Tool of known dimensions mounted on the robot flange


It is necessary that a tool of known dimensions and declared in the $TOOL system
variable has been mounted on the robot flange. It is best to use the Tool Master or
Calibrated Tool (the same used for the TOOL automatic calculation (see TOOL
automatic calculation)). As an alternative it is also possible to use a point identified on
the work tool, that has a distance from the robot flange centre that is precise and known.

18.6.1.2 3 reference points (P1, P2, P3)


The 3 reference points are always present on the COMAU positioners.
These may be threaded holes, to fasten the 150 mm. calibrated tool or references
stamped on the positioner.

18.6.2 General characteristics


– The robot positions on the 3 points are not rigid: the operator can position the TCP
on the references at will, according to requirements.
– The calculated values will be saved in UD:\SYS\ in the .C5G system file and thus
can be recovered using Config. (F1) command, Load the configuration file
(CLA), SETUP Page on the Teach Pendant.
– The positioner can be seen by the system either as an auxiliary axis or as ARM (in
the case of double arm). In the first case the axis to which the positioner is
associated must be defined.
– The calculated values will be automatically assigned to the following system
variables:
• For an auxiliary axis:
$ARM_DATA[narm].AUX_BASE[npositioner]

HS-0-C5E-USO_44.fm
08/1012 243
TO_SET Program - Tool handling

• For arm:
$ARM_DATA[narm].BASE

Fig. 18.47- Screen page 5.1

Draws the operator’s attention to the values of the currently declared $TOOL variable.
The values must refer to the tool mounted on the flange and will be used for the
calculation of $BASE or $AUX_BASE. When these values are displayed, they can be
modified if necessary.
Accepted commands:

F1: procedure cont. (Fig. 18.48)


F2: to change the values of $TOOL (Fig. 18.57)
F6: returns to main menu (Fig. 18.2)

Fig. 18.48- Screen page 5.2

Draws the operator’s attention to the values of the calibrated tool used as reference on
points P1, P2, P3. The values are displayed and can be modified if necessary.
Accepted commands:

F1: continues procedure (Fig. 18.49)


F2: to change the values of the reference calibrated tool (Fig. 18.57)
F6: returns to main menu (Fig. 18.2)

HS-0-C5E-USO_44.fm
244 08/1012
TO_SET Program - Tool handling

Fig. 18.49 - Screen page 5.3

To select the type of positioner for the BASE calculation.


AUX: positioner seen as an auxiliary axis; ARM: positioner seen as an ARM.
Accepted commands:

F1: type of ARM; continue (Fig. 18.50)


F2: type of auxiliary axis; continue (Fig. 18.51)
F6: returns to main menu (Fig. 18.2)

Fig. 18.50 - Screen page 5.4

To insert the positioner ARM number (1-4).


If the entered ARM number is not acknowledged by the system, the screen page of
Fig. 18.59 is displayed; if it is acknowledged, the screen page of Fig. 18.52 is displayed.
Accepted commands:

<esc>: omits the insertion (returns to the screen page of Fig. 18.49)

HS-0-C5E-USO_44.fm
08/1012 245
TO_SET Program - Tool handling

Fig. 18.51- Screen page 5.5

To insert the positioner number (1-4).


If the entered positioner number is not acknowledged by the system, the screen page of
Fig. 18.60 is displayed; if it is acknowledged, the screen page of Fig. 18.52 is displayed.

The [narm] (to which the selected positioner is associated) assumed by TO_SET is the
one displayed on the TP in the field [Ar:] at the moment in which the positioner number
is inserted

Accepted commands:

<esc>: omits the insertion (returns to the screen page of Fig. 18.49)

Before going on with the next step, check that all the positioner axes are in 0° position,
otherwise the “Not valid position” error will occur.

Fig. 18.52- Screen page 5.6

Asks the operator to move the tool TCP to point P1.


The robot can assume any position: the operator can move the TCP to point P1 as
desired, according to the requirements.
Accepted commands:

HS-0-C5E-USO_44.fm
246 08/1012
TO_SET Program - Tool handling

F1: to press when the robot is on position; continue (Fig. 18.53)


F6: returns to main menu (Fig. 18.2)

Fig. 18.53 - Screen page 5.7

Asks the operator to move the tool TCP to point P2.


The robot can assume any position: the operator can move the TCP to point P2 as
desired, according to the requirements.
Accepted commands:

F1: to press when the robot is on the point; cont. (Fig. 18.54)
F6: returns to main menu (Fig. 18.2)

Fig. 18.54 - Screen page 5.8

Asks the operator to move the tool TCP to point P3.


The robot can assume any position: the operator can move the TCP to point P3 as
desired, according to the requirements.
Accepted commands:

F1: to press when the robot is on the point; cont.(Fig. 18.55 or Fig. 18.61)
F6: returns to main menu (Fig. 18.2)

HS-0-C5E-USO_44.fm
08/1012 247
TO_SET Program - Tool handling

Fig. 18.55- Screen page 5.9

Displays the calculated $BASE or $AUX_BASE values (XYZ displacements and AER
orientations).
At this moment the positioner axes can be moved in JOINT selecting the ARM number
(if the positioner is an ARM), to check that the cooperating move between robot and
positioner is correct.
If not, check the following:
– the robot calibration;
– the $TOOL values (they are to refer to the tool mounted on the flange);
– if there are several positioners, check that the number of the positioner is that
actually used for the calculation (Fig. 18.50 or Fig. 18.52).
– the 3 reference points (check that the sequence required by TO_SET has been
respected).
Accepted commands:

F1: returns to screen page in Fig. 18.47


F2: saves calculated values.
Note: to perform the SAVE operation, it is necessary to be in PROG +
DRIVES OFF; procedure continue (Fig. 18.56 or Fig. 18.62)
F6: returns to main menu (Fig. 18.2)

Fig. 18.56- Screen page 5.10

HS-0-C5E-USO_44.fm
248 08/1012
TO_SET Program - Tool handling

Displayed if the SAVE request has been performed. The calculated values assigned to
the opportune system variables have been successfully saved in the .C5G system file.
Accepted commands:

F1: returns to screen page in Fig. 18.47


F6: returns to main menu (Fig. 18.2)

Fig. 18.57 - Screen page 5.11

Displays the currently declared $TOOL values (XYZ displacements and AER
orientations) and allows their modification.
Accepted commands:

<esc>: permits the omission of each separate value insertion

Fig. 18.58 - Screen page 5.12

Displays the values of the reference calibrated tool (XYZ displacements) and allows
their modification.
Accepted commands:

<esc>: allows omitting each separate value insertion

HS-0-C5E-USO_44.fm
08/1012 249
TO_SET Program - Tool handling

Fig. 18.59- Screen page 5.13

Displayed if an ARM type positioner has been entered that is not acknowledged by the
system (see Fig. 18.50).
Accepted commands:

F1: returns to screen page in Fig. 18.49


F6: returns to main menu (Fig. 18.2)

Fig. 18.60- Screen page 5.14

Displayed if an AUX type positioner has been entered that is not acknowledged by the
system (see Fig. 18.52).
Accepted commands:

F1: returns to screen page in Fig. 18.49


F6: returns to main menu (Fig. 18.2)

HS-0-C5E-USO_44.fm
250 08/1012
TO_SET Program - Tool handling

Fig. 18.61 - Screen page 5.15

Displayed if it is not possible to perform the $BASE calculation.


Check:
– the robot calibration;
– the $TOOL values (they are to refer to the tool mounted on the flange);
– the declared values of the reference calibrated tool;
– the 3 reference points (check that the sequence required by TO_SET has been
respected).
Accepted commands:

F1: returns to screen page in Fig. 18.47


F6: returns to main menu (Fig. 18.2)

Fig. 18.62 - Screen page 5.16

Displayed when a SAVE operation (from Fig. 18.55) has been requested but the C5G
is not in PROG + DRIVES OFF. This condition is necessary since the SAVE operation
requires the system command Config. (F1), Save the configuration file, SETUP
Page.
Accepted commands:

F1: returns to screen page in Fig. 18.55


F6: returns to main menu (Fig. 18.2)

HS-0-C5E-USO_44.fm
08/1012 251
TO_SET Program - Tool handling

18.7 Payload identification (optional function)

Automatic Payload Identification


The option code is CR17926202.

Press F4 key in the screen page in Fig. 18.2, to access this procedure.

The new generation robots (NJ and NJ4) are fitted with a complete dynamic model
on all six axes.
Because of the model's sensitivity to the declared payload parameters, it is necessary
that the user checks in every situation the correct definition of the used payload.
An imprecision in the declaration of the payload characteristics has a negative influence
on the robot performance.

Warning: for safety reasons it is very important that the machine is not used before
having defined the payload values.
The omission or a big error in the payload declaration could create potentially hazardous
situations for the users and for the fixtures

This paragraph supplies information regarding


– Basic concepts regarding Payload identification
– Procedure for Payload identification
– Software to validate the payload (SMART Payload).

18.7.1 Basic concepts


As the correct declaration of the tool dimensions (variable $TOOL) is necessary to
obtain the required precision in execution of movements in the Cartesian environment,
in the same way it is equally necessary to correctly define the payload parameters that
will have influence on the robot movements in terms of performance optimisation and
safeguarding the components.
The determination of the payload characteristics takes place using the specific
procedure.

During the Payload Identification procedure also the outfitting weight (e.g.: cable) is
identified.
If it is wished to execute the procedure with outfitting present (for example cables) that
exert significant traction (for example on the wrist structure), it is advised to remove them
where possible, or in any case ensure that their presence does not influence the results
of the procedure.

HS-0-C5E-USO_44.fm
252 08/1012
TO_SET Program - Tool handling

For the identification, Comau does not ask for movements WITHOUT load, but only
WITH load.

The Payload identification procedure, running the execution from two separate
movement programs that involve the wrist axis, and, in part, axis 3 of the robot,
recalculates the values of the following system variables:
– $TOOL_MASS (kg)
– $TOOL_CENTER (x, y and z)
– $TOOL_INERTIA[1..6] (it is only necessary to supply items from I1 to I6, in
kg/sq.m, since the Inertia matrix is symmetrical). The useful reference system to
define the Inertia matrix is that of the tool ($TOOL_CENTER), with origin in COG
(Centre Of Gravity).
Once this has been determined, the parameters will be immediately active and
automatically stored in the specific table created by TO_SET (TT_TOOL1.var), to be
called up when executing the movement cycles, each time the same payload is used.

It may be that individually the values produced by the Payload identification procedure
have a certain tolerance in relation to the actual values. In any case, the way the
dynamic model is designed, the consistency of these values is important.

18.7.2 Procedure
The motion programs for the Payload identification are supplied by Comau in PDL2
language and differ depending on the robot model, on the basis of the robot kinematic
features. Their use is strongly recommended, unless there are physical impediments in
the robot working area.

Before installation, check that the overall dimensions caused by the presence of any
fixtures installed in the robot operating area, allows the complete execution of the
programs available for the Payload identification, supplied by Comau.
If there is not space enough, it is advised to run this procedure BEFORE the final
positioning of the robot in the cell or line; if, in spite of the limited space, it is decided to
run the procedure, the user can change the Payload identification programs, reducing
the axis strokes and/or changing the position of some of them (for example axis 1 and
2): in any case, the variations are to be made in compliance with the fundamental
requirements needed for the modification of the Payload identification programs (see
par. 18.7.2.1 Requirements to modify Payload identification programs on page 254).

The entire Payload Identification procedure is performed with the DYNAMIC MODEL
DEACTIVATED automatically by the system.

This paragraph contains the following information:


– Requirements to modify Payload identification programs
– Activation and execution of the Payload identification procedure

HS-0-C5E-USO_44.fm
08/1012 253
TO_SET Program - Tool handling

18.7.2.1 Requirements to modify Payload identification programs


When changing Payload identification programs be sure to:
– Keep axis 3 in horizontal position
– have appropriate extension of the strokes of the axes involved.
The user can intervene, reducing the movement frequency of the individual axes, move
axis 1 as desired and move axes 2 and 3 as necessary, but ALWAYS ensuring that axis
3 is horizontal to the floor.
Since any modifications made to movement programs could reduce the precision of the
Identification procedure results, upon request Comau Robotica can supply an off-line
instrument to validate the results. See par. 18.7.2.3 Software to validate the payload
(SMART Payload) on page 263.

18.7.2.2 Activation and execution of the Payload identification procedure

Press F4 key from the screen page in Fig. 18.2, to access this procedure.

a. If TO_SET program is to be installed again, follow par. 18.2 Activation on page 211
description.

b. The User is requested to insert the Payload number:

Fig. 18.63- LOAD number

c. Specify whether the tool is remote or not:

HS-0-C5E-USO_44.fm
254 08/1012
TO_SET Program - Tool handling

Fig. 18.64 - Remote or Local Tool

if remote, the calculated data will be saved to TU_FRAME.VAR table; if local, they
will be saved to TT_TOOL.VAR table

d. the modal selector switch must be set to T1 (if necessary, reposition it)

e. keep the Enabling Device pressed on the Teach Pendant

f. press START key to move the robot to calibration position

The procedure includes movements that involve axes 3, 4, 5 and 6.

HS-0-C5E-USO_44.fm
08/1012 255
TO_SET Program - Tool handling

g. if the calibration position has been reached, choose MOVE EXECUTED (F1) to
directly go to step h.
If it is not possible to reach the calibration position, the start position has to be
changed: choose CHANGE START POS (F2). The following screen page is
displayed:

g.1 Use the jog keys to move the robot to the new start position (remember to ALWAYS
keep axis 3 parallel to the base!). Choose MOVE EXECUTED (F1): if the system
does not accept the new start position, repeat this step. When the Move is finally
executed correctly, continue with the next step.

h. this screen page is shown:

Run the verification program. If it has terminated correctly, choose TEST


FINISHED (F1). If the robot is NJ4 series, a second test is suggested and therefore
this point is executed again. Otherwise pass directly to point j.
If the verification program has not terminated correctly, choose POSITION
MODIFY (F2).

i. if the choice is POSITION MODIFY (F2), to change the start point or reduce the
stroke of one or more axes, the following screen page is displayed:

HS-0-C5E-USO_44.fm
256 08/1012
TO_SET Program - Tool handling

i.1 to change the start position select CHANGE INITIAL POS (F1); in this case
execute the same operations as indicated in step g.1.
If instead it is wished to reduce the stroke of one or more axes, select REDUCING
MOVEMENTS (F2).
The system displays the involved axes and the corresponding selection keys:

i.2 Choose the axis for the stroke reduction, or select CONTINUE (F5) to return to step
h., without making any further modifications

i.3 Each time that either F1 or F2 key is pressed (for positive and negative direction
respectively), the stroke of the selected axis will be reduced by a pre-defined
quantity. If the initial values are to be resumed, choose RESET INITIAL VALUES

HS-0-C5E-USO_44.fm
08/1012 257
TO_SET Program - Tool handling

(F3). When finished, choose CONTINUE (F5) to return to step i.2

j. this screen page is shown.

before starting to execute real Payload identification programs, it is advised to


warm up the robot, making movements that involve the wrist and axis 3. If it is
decided not to run an automatic warm-up, select NO (F2) and go to step k.; if it is
decided to run the automatic warm-up, select YES (F1)

If HOLD is pressed, the procedure is interrupted and cannot be continued.

j.1 set the required speed

j.2 set the modal selector switch to AUTO

j.3 switch on the drives pressing DRIVE ON and press START key

HS-0-C5E-USO_44.fm
258 08/1012
TO_SET Program - Tool handling

j.4 the automatic warm-up program is then executed. Wait until finished

j.5 select CONTINUE (F1)

k. this screen page is shown:

set GEN_OVR at 100% then choose CONFIRM YES (F1)

HS-0-C5E-USO_44.fm
08/1012 259
TO_SET Program - Tool handling

l. switch off the drives by pressing DRIVE OFF

m. check that the modal selector switch is set to AUTO

n. switch on the drives pressing DRIVE ON and press START key

While running, the cycle number of the current program is displayed, on the
number of total cycles to be run.

o. the execution of the first movement program starts (slow). Wait until finished

HS-0-C5E-USO_44.fm
260 08/1012
TO_SET Program - Tool handling

p. select CONTINUE (F1)

q. if the overall dimensions, the payload and the tool structure allow the execution of
the second program at normal speed, select YES (F1), otherwise select NO (F2).
If NO (F2) is chosen, the second Identification program will be run at a slower
speed

r. switch off the drives, pressing DRIVE OFF

s. check that the modal selector switch is set to AUTO

HS-0-C5E-USO_44.fm
08/1012 261
TO_SET Program - Tool handling

t. switch on the drives pressing DRIVE ON and press START

u. the execution of the second motion program starts (at normal speed). Wait until
completion

v. switch off the drives, pressing DRIVE OFF.

The system processes the data collected during the execution of the two motion
programs. When processing has been completed, a screen page is shown
containing the calculated values (weight, centre of weight and inertia). Choose
SAVE (F1) to save them in the suitable DATA environment table and file:

HS-0-C5E-USO_44.fm
262 08/1012
TO_SET Program - Tool handling

– TT_TOOL.VAR if the TOOL is LOCAL


– TU_FRAME.VAR if the TOOL is REMOTE.
This terminates the procedure and the initial choice screen page returns
(Fig. 18.4).
To exit choose RETURN TO MENU (F6).

18.7.2.3 Software to validate the payload (SMART Payload)


Comau Robotics supplies, upon request, an off-line software tool called SMART
Payload, that can check the correctness of the values calculated by the Payload
identification procedure .
This tool checks that the obtained payload values are within the limits set by the static
load curve of the specific robot.

HS-0-C5E-USO_44.fm
08/1012 263
Interference Regions (optional feature)

19. INTERFERENCE REGIONS (OPTIONAL


FEATURE)

Interference Regions
The option code is CR17926216.

19.1 Introduction
Interference Regions are interference/interchange volumes shared between Robot and
Robot, and between Robot and structures.
Their handling allows to interact among machines, optimizing the use of the cell inside
space, in order to guarantee the collision prevention, upon defining the geometry of the
Robot working zone inside volumes.
In the Interference Regions handling system, a library has been created of basic
geometrical shapes allowing to support most functional cases, to control both cartesian
and joint working areas.
Both for cartesian and joint case, it is allowed to define 16 geometrical regions to be
used both to monitor and block the Robot to enter them.
– Regions types
– Regions Shape and definition
– IR_LIB library to support Interference Regions creation
– Examples.

19.2 Regions types


Two kind of Regions are defined:
– Forbidden Regions
• Cartesian Forbidden and Allowed Regions
• Joint Forbidden Regions
– Monitored Regions
• Cartesian Monitored Regions
• Joint Monitored Regions.
Each one of them can be either Cartesian, if defined by a volume with predefined
geometrical shape, or Joint, if defined by robot axes allowed stroke intervals.
One more Region type depends on the permanence feature of the Region. In particular,
for any Region type it is allowed to declare it to be Permanent, which means that the
Region is memory resident, active and doesn’t depend on the being executed program.
On the contrary, the non Permanent Region depends on the program in which it has
been defined and it is automatically deactivated as soon as such a program is
deactivated.

pr-0-0-gpr_13.fm
264 08/1112
Interference Regions (optional feature)

19.2.1 Cartesian Forbidden and Allowed Regions


In these Regions the TCP (Tool Center Point) will never be allowed to either enter
(Forbidden) or exit (Allowed). The algorithm takes charge of slowing down the Robot
properly in advance, so that the velocity goes to zero on the Region boundary.

For using the Allowed regions, the following option is required:


Advanced Interference Regions
code CR17926218.

The Robot is constantly monitored in any System state (both in AUTO and PROGRAM
state) and the TCP velocity is modified depending on the distance from the Forbidden
Region; this functionality implies that when the TCP is close to the Interference Region,
the Robot velocity is reduced, proportionally to its distance from the Region.

This kind of modality and functionality is useful whenever it is needed to define some
Regions which the Robot should either NEVER enter (Forbidden) or NEVER EXIT from
(Allowed), and also should NEVER work in close proximity of its boundaries, at
maximum speed. The Robot, in fact, slows down its motion proportionally to the distance
from the specified region surface.

19.2.2 Cartesian Monitored Regions


Whenever the TCP either enters or exits from such Regions, a programmable boolean
value is written to a logical output port, available to the User.

Such a logical port is associated to the Region by means of IR_SET built-in routine
(detailed description in chap.BUILT-IN Routines List - PDL2 Programming Language
Manual).

19.2.3 Joint Forbidden Regions


The Robot axes will NEVER be allowed to enter such Regions. The algorithm slows
down the Robot properly in advance (taking care of each axis velocity component), so
that the velocity goes to zero on the Region boundary.
The Joint Forbidden Regions functioning principle is the stroke ends one, with some
additional functions. The User is allowed to specify which joints are to be monitored to
avoid reaching the Forbidden Regions, thus it is possible to define even just one joint to
comply with some limitations. Particularly, it is possible to define an interval
(e.g. [-20°, +50°]) inside which an axis motion must be restricted. The system takes care
of restricting the axis motion to the positive and negative ends specified by the User.

19.2.4 Joint Monitored Regions


Whenever an axis either enters or exits from such Regions, a programmable boolean
value is written to a logical output port, available to the User.

pr-0-0-gpr_13.fm
08/1112 265
Interference Regions (optional feature)

Such a logical port is associated to the Region by means of IR_SET built-in routine
(detailed description in chap.BUILT-IN Routines List - PDL2 Programming Language
Manual).

The Joint Monitored Regions functioning principle is the electronic cams one, where it
is allowed to define some stroke intervals for an axis, upon which a logical port is set to
ON/OFF values.
For example, it is possible to define a Joint Monitored Region to monitor axes 1, 4 and
6 so that, as soon as the monitored joints values are inside the defined intervals, the
system sets to ON/OFF values a previously defined by the User logical port.

19.3 Regions Shape and definition


– Cartesian Regions shape and definition
– Joint Regions shape and definition.

19.3.1 Cartesian Regions shape and definition


There are four shapes for Cartesian Regions:
– Sphere
– Cylinder
– Box
– Plane.
Such Regions position and dimension definition is auto-taught, by means of the IR_DEF
setup tool. As an alternative, it is also possible to create PDL2 programs calling suitable
routines and built-in routines. For further details see par. 19.4 IR_LIB library to support
Interference Regions creation on page 269.
In the auto-teach procedure the TCP is moved to some basic points of the above listed
shapes, following a guided sequence on the Teach Pendant.
For each shape a procedure is available which starts defining a reference frame and
continues defining some geometric values (radius, height, width, depth, ...), or
auto-teaches some more points.

19.3.1.1 Sphere
By means of teaching point P1 (center of the sphere), the frame is defined (no matter
the orientation) to correspond to the center of the sphere. The radius is assigned by the
User at the end of the guided procedure or by means of a PDL2 program. In such a way
the frame corresponding to P1 and the geometric value sphere radius are stored.

pr-0-0-gpr_13.fm
266 08/1112
Interference Regions (optional feature)

Fig. 19.1 - Sphere

R - radius

19.3.1.2 Cylinder
By means of sequentially teaching points P1 and P2, the frame and the cylinder height
are defined. The radius is assigned by the User at the end of the guided teaching
procedure.
In details:
– P1 defines the frame origin.
– P2 defines cylinder height and orientation.

Fig. 19.2 - Cylinder

H - height R - radius

19.3.1.3 Box
By means of sequentially teaching P1, P2, P3 points, frame and two dimensions (width
and depth), are defined, whereas by means of teaching P4 point height is defined. In
such a way, the calculated frame (by means of POS_FRAME(P1, P2, P3)) and the three
geometric values, width (P2-P1), depth (P3-P1) and height (P4-P1), are stored.
In details:
– P1 defines the frame origin.
– P2 defines width axis.
– P3 defines base plane and depth.

pr-0-0-gpr_13.fm
08/1112 267
Interference Regions (optional feature)

– P4 defines height.

Fig. 19.3 - Box

H - height W - width D - depth

19.3.1.4 Plane
By means of sequentially teaching P1, P2, P3 points, the frame is defined. In such a way
the calculated frame (by means of POS_FRAME(P1, P2, P3)) is stored. The defined
Region is shown in Fig. 19.4.

Fig. 19.4 - Plane

19.3.2 Joint Regions shape and definition


A Joint Region is a set of values, expressed either in degrees (rotational axis) or in
millimeters (linear axis), of a whole Arm, delimitating the axes allowed strokes. The User
can choose which axes to control.
Such strokes can be defined in two different ways:
– Specify the center of the allowed stroke, and the stroke tolerance within
which the axis must move.
The axes are positionned in the allowed stroke center. The tolerance is specified
by means of the User Interface.
– Specify the allowed stroke ends.
The axes are first positioned in the lowest end and then in the highest end of the
allowed strokes.

pr-0-0-gpr_13.fm
268 08/1112
Interference Regions (optional feature)

Such Regions position and dimension definition is auto-taught. As an alternative, it is


also possible to create PDL2 programs calling suitable routines and built-in routines. For
further details see par. 19.4 IR_LIB library to support Interference Regions creation on
page 269.

19.4 IR_LIB library to support Interference Regions


creation
By means of this library, automatically loaded in memory at the Controller Unit Startup,
the User can intuitively declare the wished cartesian and joint Interference Regions.
The previously described geometric shapes for Cartesian Regions, can be defined by
means of PDL2 programs calling the following routines:
– IR_CreateSphere (ap_p1, ar_R, ai_num_arm, ai_t_idx)
– IR_CreateCylinder (ap_p1, ap_p2, ar_R, ai_num_arm, ai_t_idx)
– IR_CreateBox (ap_p1, ap_p2, ap_p3, ap_p4, ai_num_arm, ai_t_idx)
– IR_CreatePlane (ap_p1, ap_p2, ap_p3, ai_num_arm, ai_t_idx)
Furthermore, the following routine is given to declare Joint Regions:
– IR_CreateJoint (aj_neg_joint, aj_pos_joint, ai_num_arm, ai_mask, ai_t_idx)
Such routines are to be imported by the calling program either using the EXPORTED
FROM clause:

ROUTINE IR_CreateSphere (ap_p1 : POSITION; ar_R : REAL; ai_num_arm ai_t_idx :


INTEGER) : BOOLEAN EXPORTED FROM IR_LIB GLOBAL
ROUTINE IR_CreateCylinder (ap_p1, ap_p2 : POSITION; ar_R : REAL; ai_num_arm,
ai_t_idx : INTEGER) : BOOLEAN EXPORTED FROM IR_LIB GLOBAL
ROUTINE IR_CreateBox (ap_p1, ap_p2, ap_p3, ap_p4 : POSITION; ai_num_arm, ai_t_idx
: INTEGER) : BOOLEAN EXPORTED FROM IR_LIB GLOBAL
ROUTINE IR_CreatePlane (ap_p1, ap_p2, ap_p3 : POSITION; ai_num_arm, ai_t_idx :
INTEGER) : BOOLEAN EXPORTED FROM IR_LIB GLOBAL
ROUTINE IR_CreateJoint (aj_neg_joint, aj_pos_joint : JOINTPOS; ai_num_arm,
ai_mask, ai_t_idx : INTEGER) : BOOLEAN EXPORTED FROM IR_LIB GLOBAL

or by means of the IMPORT statement:

IMPORT ‘IR_DEF’

These functions can be used to allow the User to intuitively create both cartesian and
joint Regions, following the above described instructions.

Example 1
An example follows to define a cylindrical cartesian region from within a program:

pr-0-0-gpr_13.fm
08/1112 269
Interference Regions (optional feature)

-- Cylinder definition: base=pnt0007P, height=pnt0008P, radius=200 mm,


-- used for arm 1, Interference Region number 3

-- Creating Cartesian Region number 3


IR_CreateCylinder(pnt0007P, pnt0008P, 200, 1, 3)

-- Associating Cartesian Region number 3 to digital output $FMO[1], bit 2,


indicating that it is monitored
IR_SET($FMO[1], 2, 3, IR_PRESENCE, OFF)

-- Activating Cartesian Region number 3


IR_SWITCH(ON, 3)

Previous code allows to create a monitored, non permanent, cylindrical (base -


pnt0007P, height - pnt0008P, radius 200 mm) Interference Region.
The Region, defined as number 3 in $IR_TBL table, will assign the predefined value of
OFF to the digital output bit 2 of $FMO[1], as soon as the TCP enters such a Region.

Example 2
In the following example a PDL2 program section is shown which creates a Joint
Monitored Region for axis 6 only.

ROUTINE IR_CreateJoint (aj_neg_joint, aj_pos_joint : JOINTPOS; ai_num_arm,


ai_mask, ai_t_idx : INTEGER) : BOOLEAN EXPORTED FROM IR_LIB GLOBAL

...............
...............

aj_neg_joint[6] := -60 -- axis 6 negative end


aj_pos_joint[6] := 60 -- axis 6 positive end
ai_arm := 1 -- arm number
ai_mask := 0b00100000 -- axis 6 binary mask
-- Creating Joint Region number 4
IR_CreateJoint(aj_neg_joint,aj_pos_joint,ai_arm,ai_mask,4)
-- Associating Joint Region number 4 to digital output $FMO[1], bit 3, indicating
that it is monitored
IR_SET($FMO[1], 3, 4, IR_PRESENCE, ON)

-- Activating Joint Region number 4


IR_SWITCH(ON, 4)

The above listed code inform the System that Interference Region number 4 is active as
a Joint Monitored Region and axis 6 is monitored in range [-60, 60]. This means that as
soon as axis 6 enters the declared range, bit 3 of $FMO[1] is immediately set to ON, as
declared by IR_SET($FMO[1],3,4, ON) built-in routine.

When a program is deactivated, which had executed IR_SWITCH(ON,...), the system


automatically performs IR_SWITCH(OFF, ai_t_idx) for the Regions which had
previously been activated by such a program.

pr-0-0-gpr_13.fm
270 08/1112
Interference Regions (optional feature)

19.5 Examples
– Sample program for Cartesian Interference Regions
– Sample program for a Joint Interference Region.

pr-0-0-gpr_13.fm
08/1112 271
Interference Regions (optional feature)

19.5.1 Sample program for Cartesian Interference Regions


Here follows a PDL2 program sample which defines and uses some cartesian
Interference Regions within a Robot motion program.

PROGRAM ir_cart PROG_ARM = 1


VAR pnt0001J, pnt0002J, jnt0018J, jnt0019J , jnt0020J, jnt0021J, jnt0022J,
jnt0023J : JOINTPOS FOR ARM[1]
pnt0001P, pnt0002P, pnt0003P, pnt0004P, pnt0005P, pnt0006P, pnt0007P, pnt0013P,
pnt0014P, pnt0015P, pnt0016P : POSITION

ROUTINE IR_CreateBox(ap_p1, ap_p2, ap_p3, ap_p4 : POSITION; ai_num_arm, ai_t_idx :


INTEGER) : BOOLEAN EXPORTED FROM IR_LIB GLOBAL
ROUTINE IR_CreateSphere(ap_p1 : POSITION; ar_R : REAL; ai_num_arm, ai_t_idx :
INTEGER) : BOOLEAN EXPORTED FROM IR_LIB GLOBAL
ROUTINE IR_CreateCylinder(ap_p1, ap_p2 : POSITION; ar_R : REAL; ai_num_arm,
ai_t_idx : INTEGER) : BOOLEAN EXPORTED FROM IR_LIB GLOBAL
ROUTINE IR_CreatePlane(ap_p1, ap_p2, ap_p3 : POSITION; ai_num_arm, ai_t_idx :
INTEGER) : BOOLEAN EXPORTED FROM IR_LIB GLOBAL
ROUTINE ToolFrame(ai_tool, ai_frame, ai_arm : INTEGER()) EXPORTED FROM TT_TOOL
GLOBAL

BEGIN
ToolFrame(3, 0) -- tool 3, frame 0

-- defining some Interference Regions


-- Region 1 --> box
IR_CreateBox(pnt0001P, pnt0002P, pnt0003P, pnt0004P, 1, 1)
-- Region 5 --> box
IR_SET($FMO[1], 1, 5, IR_PRESENCE) --associating bit 1 of $FMO[1] to region 5
-- which then becomes a monitored region
IR_CreateBox(pnt0013P, pnt0014P, pnt0015P, pnt0016P, 1, 5)
-- Region 2 --> cylinder
IR_CreateCylinder(pnt0005P, pnt0006P, 250, 1, 2)
-- Region 3 --> sphere
IR_SET($FMO[1], 2, 3, IR_PRESENCE)
-- activating always present Interference Regions
IR_SWITCH(ON, 1) -- activating region 1
IR_SWITCH(ON, 5) -- activating region 5
CYCLE
MOVE TO pnt0001J
IR_SWITCH(ON, 2) -- activating region 2
MOVEFLY TO pnt0002J ADVANCE
MOVEFLY JOINT TO jnt0018J ADVANCE
MOVE LINEAR TO jnt0019J
IR_SWITCH(OFF, 2) -- deactivating region 2
MOVE LINEAR TO jnt0020J
IR_SWITCH(ON, 3) -- activating region 3
MOVEFLY JOINT TO jnt0021J ADVANCE
MOVE LINEAR TO jnt0022J
IR_SWITCH(OFF, 3) -- deactivating region 3
MOVE LINEAR TO jnt0023J

END ir_cart

pr-0-0-gpr_13.fm
272 08/1112
Interference Regions (optional feature)

19.5.2 Sample program for a Joint Interference Region


Here follows a PDL2 program sample which defines and uses a Joint Interference
Region within a Robot motion program.

PROGRAM ir_jnt PROG_ARM = 1


VAR pnt0001J, pnt0002J, jnt0018J, jnt0019J , jnt0020J, jnt0021J, jnt0022J,
jnt0023J : JOINTPOS FOR ARM[1]
pnt0001P, pnt0002P, pnt0003P, pnt0004P, pnt0005P, pnt0006P, pnt0007P, pnt0013P,
pnt0014P, pnt0015P, pnt0016P : POSITION

ROUTINE IR_CreateJoint(aj_neg_joint, aj_pos_joint : JOINTPOS; ai_num_arm, ai_mask,


ai_t_idx : INTEGER) : BOOLEAN EXPORTED FROM IR_LIB GLOBAL

BEGIN
--
-- Defining Joint Interference Region number 2
--
IR_SET($FMO[1], 1, 2, IR_PRESENCE) -- Associating bit 1 of $FMO[1] to region 2
-- which then becomes a monitored region
-- Defining axis 3 (arm 1) limitations
aj_neg_joint[3] := -75
ai_arm := 1
ai_mask := 0b00000100 -- axis 3 binary mask
IR_CreateJoint(aj_neg_joint,aj_pos_joint,ai_arm,ai_mask,2)

-- Activating Interference Region number 2


IR_SWITCH(ON, 2)

CYCLE
MOVE TO pnt0001J
MOVEFLY TO pnt0002J ADVANCE
MOVEFLY JOINT TO jnt0018J ADVANCE
MOVE LINEAR TO jnt0019J
MOVE LINEAR TO jnt0020J
MOVEFLY JOINT TO jnt0021J ADVANCE
MOVE LINEAR TO jnt0022J
MOVE LINEAR TO jnt0023J
END ir_jnt

pr-0-0-gpr_13.fm
08/1112 273
Axes Pursuit (optional feature)

20. AXES PURSUIT (OPTIONAL FEATURE)

Axes Pursuit
The option code is CR17926217.

20.1 Introduction
The Axes pursuit functionality makes it possible moving, both in Automatic and
Programming mode, one or more axes belonging to one Arm (called the MASTER)
allowing one or more axes of a different Arm (called the SLAVE) to pursue the MASTER
Arm axes.
– Axes Pursuit
– Error handling when Axes Pursuit functionality is active
– Configuring the software option.

20.2 Axes Pursuit


The Axes Pursuit optional functionality allows to define that one or more axes of a
SLAVE Arm can pursue one or more axes of a MASTER Arm.
The pursuer axes (including the payload) must have the same dynamic features of the
pursued axes, in order to assure a proper pursuit during the acceleration/deceleration
phases and for the maximum speed of the pursuer axes.
If not, it is not guaranteed a good pursuit of the MASTER Arm axis/axes by the SLAVE
Arm axis/axes.
An example of axes pursuit application is the pursuit between two slides: one carrying a
robot and the other one pursuing the translational motion of the robot, e.g. to carry the
welding wire.
The system works both in automatic and in programming mode; in both cases, the
functionality can be activated/deactivated at any time, to be able to guarantee the two
(or more) axes independency.
In programming mode it is possible to select a modality, by means of
$AX_PURSUIT_ENBL predefined variable, in which the ppursuit of all the SLAVE axes
can be activated/deactivated on all the involved MASTER axes.
In such a way, it is possible to move the involved axes both independently and with the
axes pursuit functionality active.
In automatic mode it is possible to activate/deactivate the axes pursuit functionality
during the work program execution, by means of $AX_PURSUIT_ENBL predefined
variable.

pr-0-0-gpr_14.fm
274 08/1012
Axes Pursuit (optional feature)

As soon as the functionality is activated, the MASTER Arm axis pursuit made by the
SLAVE Arm axis, starts from the current position of the SLAVE Arm axis. So, the relative
delta between pursuer/pursued axis remains unchanged, but it can change if the
functionality is disabled and the two axes move independently.

20.3 Error handling when Axes Pursuit functionality is


active

At the powerup of a System including the Axes Pursuit option, the functionality
default is DISABLED.
The Administrator profileis required to set to TRUE the $AX_PURSUIT_ENBL
predefined variable, to enable it.

The System which is configured to have Axes Pursuit option, handles a special clalss of
errors related to such a functionality.
First of all, if the option is activated, the system does not allow moving the SLAVE Arm
independently from the MASTER Arm.
This imply that, if $AX_PURSUIT_ENBL is set to TRUE, and an attempt to manual or by
a user program move the robot SLAVE Arm is performed, the system will return the error
message:
"Movement not allowed whith axes pursuit option activated".
During the option configuration, the system checks the correctness of the inserted data,
also according to its pre-existing configuration.
If, for example, a not expected value is set for the MASTER Arm axis in
$AX_PURSUIT_LINKED variable (e.g. a not existing MASTER axis), this situation
would cause the system to issue an error message at the startup:
"The axis of MASTER Arm does not exist".
In the case in which, at the system startup, a wrong configuration error is issued for the
Axes Pursuit option, the functionality is automatically disabled and it will not be possible
to use it until the system is properly configured.

20.4 Configuring the software option


To configure the Axes Pursuit software option, the involved variables are as follows:
– $AX_PURSUIT_ENBL - it can have TRUE/FALSE values, to enable/disable the
axes pursuit option (both in programming and automatic mode).
Example: $AX_PURSUIT_ENBL := TRUE enables the option.
– $AX_PURSUIT_ARM_MASTER - allows defining which Arm the pursued axis
belongs to, i.e. which is the MASTER Arm.
Example: $AX_PURSUIT_ARM_MASTER := 2 defines Arm 2 as the MASTER
– $AX_PURSUIT_LINKED - allows defining the pursuer axis which has to pursue
the MASTER Arm axis and defining the pursuing direction (by means of indicating
+/- sign on the axis number).

pr-0-0-gpr_14.fm
08/1012 275
Axes Pursuit (optional feature)

Example:
$AX_PURSUIT_ARM_MASTER := 1 -- indicates the MASTER Arm is
-- Arm 1

$ARM_DATA[2].AX_PURSUIT_LINKED[3] := 7 -- indicates axis 3 of


-- Arm 2 (SLAVE)
-- pursues axis 7 with
-- negative sign of
-- Arm 1 (MASTER)

20.4.1 Example of PDL2 statements for configuring the Axes


Pursuit functionality
Some PDL2 statements follow which configure the Axes Pursuit functionality for a two
ARMs System:
– the first Arm is configured as the MASTER
– the second Arm is, obviously, configured as the SLAVE
– axis 1 belonging to the SLAVE pursues axis 7 belonging to the MASTER
– axis 2 belonging to the SLAVE pursues axis 8 belonging to the MASTER.

$AX_PURSUIT_ENBL := TRUE
$AX_PURSUIT_ARM_MASTER := 1

$ARM_DATA[2].AX_PURSUIT_LINKED[1] := 7
$ARM_DATA[2].AX_PURSUIT_LINKED[2] := 8

pr-0-0-gpr_14.fm
276 08/1012
Low resolution Euler Angles (optional feature)

21. LOW RESOLUTION EULER ANGLES


(OPTIONAL FEATURE)

Low Resolution Euler Angles


The option code is CR17926219.

A software option exists which allows to always have lower precision in small orientation
variations around X and Y axes.
Using such an option, the precision is 0.2 degrees, instead of 0.02 degrees, default
value.
Such a functionality is useful when creating POSITION type points is required, e.g. by
means of the ‘:’ operator.
It is exactly like using bit 23 of $CNTRL_INIT predefined variable. For further
information, please refer to PDL2 Programming Language manual - chap. Predefined
Variables List.

hs-0-0-mot_08.fm
08/1012 277
COMAU Robotics services
Repair: repairs.robotics@comau.com
Training: training.robotics@comau.com
Spare parts: spares.robotics@comau.com
Technical service: service.robotics@comau.com
comau.com/robotics Original instructions

You might also like