Professional Documents
Culture Documents
training information
DRL4210,DRS5510
Apply to:
Cin 42”~46”LED TV SET
PCB SIZE:140x70mm
SINGLE Channel
Cout IC:OZ9902C
Coil
INPUT:58V
OUTPUT:108V/600mA
LED current setting resistance
Diode
IC
DRL4210 Functional Block Diagram
24V/58V DC 直流输出
Boost Circuit
Light Bar
24V工作电压
PSU
BL_ON
OZ9902C
Controller IC Dimming
PDIM
MOSFET
3D_EN
Input
voltage Power
MOSFET
BL_ON
Dimming
MOSFET
DRL4210 DR Board Circuit (一)
The recommended
operating range of VCC
input voltage is 8V to 16V.
This is a VCC input voltage
adjustment circuit.
The ENA pin is ON/OFF
control for the controller.
The enable voltage is higher
than 2V,and the disable
voltage is less than 0.8V.
RRT
RISEN
DRL4210 DR Board Circuit (四)
Protection Features
1. Output Over-Voltage Protection
When the voltage at OVP exceeds a typical
LED+ threshold of approximately 3V,the OVP function
is activated and the drive is turned off
immediately while SSTCMP pin voltage is kept
floating to maintain the drive duty cycle.
Capacitor Ctimer connected to pin TIMER is
Power charged by an approximate 6.5uA internal
MOSFET LED- current source.
Once the voltage at OVP pin drops below 3V
before the voltage at the TIMER pin exceeds
3V,the drive output resumes normal operation
and capacitor Ctimer is discharged.
If the OVP still exists when the voltage at pin
OVP TIMER exceeds 3V, the IC will shut down and
latched.
RISW
2. Output to Ground Short-Circuit Protection
An output to ground short-circuit condition is
Dimming triggered when the voltage at pin OVP is less
MOSFET than 0.2V. The IC remains in lockout mode and
the status of pin FAULT becomes an open drain.
The condition is removed when the voltage at
OVP exceeds a threshold of approximately 0.2V
and the corresponding control channel resumes
normal operation.
3. Power MOSFET Over-Current Protection
The switching current of the power MOSFET is
sensed by the resistor connected to pin ISW.
When the voltage at pin ISW exceeds a
RISEN threshold of approximately 0.5V, the power
MOSFET OCP protection function is triggered.
The power MOSFET is turned off immediately
and is not turned on until the next operation
cycle.
DRL4210 DR Board Circuit (四)
Protection Features
4. Output Over-Load Protection
During normal operation, if the voltage at ISEN
LED+ drops below ~75% of the normal operation level
set by ADIM, the output over-load protection is
triggered. An approximate 6.5uA current source
charges capacitor Ctimer connected to pin
TIMER.
Boost The IC shuts down and latches once the voltage
MOSFET LED- at pin TIMER reaches 3V. Toggle ENA to restart
the IC.
5. Output to Return Short-Circuit Protection
When the LED driver's high voltage output and
LED current return path is short-circuited during
normal operation, i.e. ISEN>1.5xADJ, the LED
OVP
current switch is turned off im mediately limiting
RISW the inrush current and an approximate 6.5uA
current source charges capacitor Ctimer
connected to pin TIMER.
Dimming During charging period of capacitor Ctimer, the
MOSFET IC periodically turns on the LED current switch to
check whether the short circuit condition still
exists. If the condition is removed before the
voltage at pin TIMER reaches a typical threshold
of approximately 3V,capacitor Ctimer is
discharged and the IC resumes normal
operation.
When the voltage at pin TIMER exceeds 3V and
the condition still exists, the corresponding
control channel shuts down ang latches. Toggle
ENA to restart the IC.
RISEN During normal operation, pin FAULT outputs a
logic low condition. When the IC enters the
shutdown or lockout mode due to any reason, as
mentioned in sections 1-5, pin FAULT becomes an
open drain.
DRS5510 Functional Block Diagram
Boost Diode
Boost Coil
Cin Cout
Power
MOSFET
Input
Signals
OZ9909
Dimming
Transistor
DRS5510 DR Board Parameters
1, DR Board input and output parameters:
Input: 24V
Output: 40V,16 channels,120mA/CH(2D);
240mA/CH(3D)
2, IC Precept:MCU+OZ9909*2
Input Vsync signal, MCU can output 8 PWM signals to control
16 channels
3, Type of DR Board:DRS5510/5511
Apply to 46/55E5500
4, Timing diagrams of interface signal
DRS5510 DR Board Circuit (一)
3D_EN and
BL_ON and PDIM signal from MB 3D Sync signal from T_CON Board
Boost
OVP=2.0V
3D Controller circuit
LED current setting resistance
Boost
2. If the DR Board has a MCU, please check the output PWM signal
from the MCU, and confirm whether the power supply circuit for
MCU is ok or not.
5. If half light bar or parts are not bright, please replace the driver
board or change the LED channel to make sure whether the
problem can be solved. If it not work, please check if the LB
socket is not fixed well or some LED is destroyed.
THANK YOU!