Professional Documents
Culture Documents
20 % reduction
in power consumption
with the SMC “Blow gun” + “S coupler” + “Coil tube”
∗10% reduction with the “Blow gun (VMG)” only
New
Extension nozzle
With cover Added 100 mm and 150 mm lengths
less
or
loss 1%
sure
res
P
M Amount of electricity used in a factory
Actuators 10%
Air 20%
Coolant 30%
DOWN
The electricity used by compressors for air accounts for approximately 20% of that consumed by the
entire factory. Also, 70% of the air consumed in the process is used for air blowing. SMC blow guns
have minimal pressure loss compared with conventional models, so they can achieve equivalent
performance at lower pressures and with less volume of air consumption. As a result, it is possible to
achieve a 20% reduction in power consumption.
Energy saving effects with Blow gun (VMG) + S coupler + Coil tube
16.0
Amount saved as a result
of energy saving effects
14.7
2,573 kWh ($257.30)/year
Note 1)
20% reduction
Electricity consumed by compressor
10.7
Conventional 10,375
model
9.3
Blow gun + S coupler + Coil tube
8.8
8,300 hours
6.6
5,000 6,000 7,000 8,000 9,000 10,000
Total working hours of use
yen/year
kW/h ($129.49)/year Note 2) Annual savings with electricity
13.3
cost at $0.10/kWh equals $129.48
compressor
0.25
Balance-poppet valve construction 30 mm 2
construction 6 mm 2
0.2
Conventional
For example,
This is 0.15 model
when you VMG (Nozzle size: ø2.5)
compare with this: the result 0.1 Pressure loss:
this:
0.05 0.725 psi (0.005 MPa) or
less with 72.5 psi (0.5 MPa)
0
0 0.2 0.4 0.6 0.8 1 MPa
Supply pressure
Features 1
SMC helps you work toward a revolutionized production system
with a focus on saving-energy.
Example of Improvement
Review the air-blow job and change to the SMC blow gun, S coupler and coil tube to create a larger effective area.
Coil tube
L L
S0 to S1 S2 S0 to S1 S2
Features 2
Blow Gun, Coil Tube and S Coupler Selection Recommended system in
accordance with the distance
Recommended system
Distance
Blow gun Nozzle size Fitting Coil tube∗ S coupler
Up to 20 mm VMG1ll-02-01 ø1 KQ2H06-02S TCU0604l-1-20-X6 KK4P-06H
Features So
As a result…
Thus…
Related Product
For pressure loss improvement S coupler: Series KK
Improved fitting’s restrictor and leakage
K Special method of K Smooth channel with
connection and fixation minimal unevenness
With a structure that employs no steel By not blocking the channel with the
balls, the coupler achieves a slim body valve spring, the loss of effective area
without narrowing of the channel, allow- can be minimized.
ing coverage of a wide effective area.
Features 3
Variations
Nozzle type
Low noise nozzle One-touch fitting type
Mono-porous nozzle (ø2) 90 to 100 dB
ø1 x 4 low noise nozzles 80 dB or less
Note) Supply pressure: 72.5 psi (0.5 MPa)
Measured at a 45 degree angle
according to JIS B 8379
With cover
∗ Achieving lower noise by dividing the air blow slit Cover for male thread nozzle
Male thread nozzle
Nozzie size: ø1, ø1.5, ø2, ø2.5, ø3, ø3.5, ø4 Bottom
<Dark blue>
Connection type
∗ Making use of Bernoulli effect and Rc, NPT, G 1/4
achieving high efficiency Screw-in type Port size
Rc, NPT, G 3/8
Copper extension nozzle
Nozzle length: 100 mm, 150 mm, KK4P-02MS
300 mm, 600 mm S coupler plug type Plug part no.
KK130P-02MS
Seals:
NBR
When using this product even at a high Resin:
pressure, the same gripping force is PBT Nozzle:
required as for a lower pressure due to the Brass
unique balance-poppet construction.
Metal:
Aluminum
Use of shock- alloy
resistant resin Stainless Recyclable
steel
Shock-resistant resin is used in the
main body. No cracks, breaks or
other damage occurred in a drop
test from a 2-meter height or in a
human stomp test.
Features 4
RoHS
Blow Gun
Series VMG
How to Order
VMG 1 1 W 02 32 C
Piping entry With nozzle cover (Only for male thread nozzle,
1 Bottom ø6 extension nozzle)
2 Top Nil None
C With nozzle cover/HNBR
CF With nozzle cover/Fluororubber
Body color
W White Nozzle
BU Dark blue Symbol Type Nozzle size Nozzle part no.
Nil Without nozzle
01 ø1 KN-R02-100
Connection size 02 ø1.5 KN-R02-150
Symbol Piping connection method Size and model no. 03 ø2 KN-R02-200
02 Rc1/4 04 Male thread nozzle ø2.5 KN-R02-250
03 Rc3/8 05 ø3 VMG1-R02-300
N02 NPT1/4 06 ø3.5 VMG1-R02-350
Threaded Thread size
N03 NPT3/8 07 ø4 VMG1-R02-400
F02 G1/4 11 ø1 KNH-R02-100
F03 G3/8 12 High efficiency nozzle ø1.5 KNH-R02-150
11 S coupler Model no. of KK4P-02MS 13 ø2 KNH-R02-200
12 plug coupler used KK130P-02MS 21 ø0.75 x 4 KNS-R02-075-4
H06 KQ2H06-02S 22 Low noise nozzle ø0.9 x 8 KNS-R02-090-8
Metric size Model no. of with male thread
H08 one-touch fitting KQ2H08-02S 23 ø1 x 4 KNS-R02-100-4
fitting used
H10 KQ2H10-02S 24 ø1.1 x 8 KNS-R02-110-8
H07 KQ2H07-35S Extension nozzle
Inch size Model no. of
H09 one-touch fitting fitting used KQ2H09-35S Symbol Type Nozzle length Nozzle size Nozzle part no.
H11 KQ2H11-35S 31 ø1.5 VMG1-06-150-300
300 mm
Note 1) S coupler and fitting are included in the same 32 ø2 VMG1-06-200-300
package. 33 ø1.5 VMG1-06-150-600
ø6 copper 600 mm
Note 2) Port size is Rc1/4 if using the S coupler plug. 34 ø2 VMG1-06-200-600
extension
Note 3) The blow gun port size is Rc1/4 if using the 35 ø1.5 VMG1-06-150-100
nozzle Note) 100 mm
metric size one-touch fitting.
36 ø2 VMG1-06-200-100
Note 4) The blow gun port size is NPT1/4 if using the inch
size one-touch fitting.
37 ø1.5 VMG1-06-150-150
150 mm
38 ø2 VMG1-06-200-150
Specifications 41 ø2.5 VMG1-08-250-100
42 100 mm ø3 VMG1-08-300-100
43 ø3.5 VMG1-08-350-100
Fluid Air 44 ø2.5 VMG1-08-250-150
45 ø8 copper 150 mm ø3 VMG1-08-300-150
Operating pressure range 0 to 145 psi (0 to 1.0 MPa)
46 extension ø3.5 VMG1-08-350-150
Proof pressure 217 psi (1.5 MPa) 47 ø2.5 VMG1-08-250-300
nozzle Note)
Ambient and fluid 48 300 mm ø3 VMG1-08-300-300
23 to 140°F (–5 to 60°C) (No freezing) 49 ø3.5 VMG1-08-350-300
temperature
50 ø2.5 VMG1-08-250-600
Flow-rate characteristics C (dm3/s·bar): 6.0, b: 0.25 51 600 mm ø3 VMG1-08-300-600
(With nozzle removed) (Effective area: 0.047 inch2 (30 mm2)) 52 ø3.5 VMG1-08-350-600
Port size Rc, NPT, G 1/4, 3/8 Note) Part number for set of extension nozzle and fitting. Extension nozzle and
Bottom Top fitting are included in the same package.
Piping entry
Refer to “How to attach extension nozzle” in the operation manual for
Nozzle port size Rc1/4 assembly procedures.
Weight (Main unit only) 5.8 oz (165 g)
Operational force (when
1.57 lbf (7 N)
the valve is fully open)
1
Blow Gun Series VMG
Construction
Component Parts
!1 qw !6 e !2 r u i No. Description Material Note
1 Body L PBT
o
2 Body R PBT
t 3 Main valve PBT
4 Valve guide POM
5 Nozzle holder Aluminium alloy Anodized
6 Port Aluminium alloy Anodized
7 Elbow PBT Only for the VMG12m
8 Cover Stainless steel
9 Ring Stainless steel
10 Arm PBT
!4 11 Spring Stainless steel
12 Main valve seal HNBR
!0
!5 13 Lever PBT
Only for the VMG11m
!7 14 Piping (bottom) POM Combined with the
y elbow u.
!9 !8 15 O-ring NBR
16 O-ring NBR
!3 17 Parallel pin Stainless steel
18 Cross recessed round head screw Stainless steel
19 Hexagon nut Stainless steel
Note) Grease is used on rubber and sliding sections.
Flow-rate Characteristics Note) Values when the main valve is fully open
Male thread nozzle 1L = 0.035 SCFM High efficiency nozzle 1L = 0.035 SCFM
14.5 29.0 43.5 58.0 72.5 87.0 102 116 131 145 psi 14.5 29.0 43.5 58.0 72.5 87.0 102 116 131 145 psi
1500 400
1400 VMG1-R02-400:ø4 KNH-R02-200
1300 VMG1-R02-350:ø3.5 350
1200 VMG1-R02-300:ø3
Flow rate [L/min (ANR)]
1100 300
KN-R02-250:ø2.5
1000
KN-R02-200:ø2 250
900
800 KN-R02-150:ø1.5 KNH-R02-150
KN-R02-100:ø1 200
700
600
150
500
400 100 KNH-R02-100
300
200 50
100
0 0
0.1 0.2 0.3 0.4 0.5 0.6 0.7 0.8 0.9 1 MPa 0.1 0.2 0.3 0.4 0.5 0.6 0.7 0.8 0.9 1 MPa
Supply pressure Supply pressure
Low noise nozzle with male thread 1L = 0.035 SCFM Copper extension nozzle 1L = 0.035 SCFM
14.5 29.0 43.5 58.0 72.5 87.0 102 116 131 145 psi 14.5 29.0 43.5 58.0 72.5 87.0 102 116 131 145 psi
900 1200
1100 VMG1-08-350-mm:ø3.5
800 KNS-R02-110-8
1000 VMG1-08-300-mm:ø3
Flow rate [L/min (ANR)]
Flow rate [L/min (ANR)]
700
900 VMG1-08-250-mm:ø2.5
600 800 VMG1-06-200-mm:ø2
KNS-R02-090-8 700
500
600
400
500
300
KNS-R02-100-4 400
300
200
200
100 KNS-R02-075-4 100
VMG1-06-150-mm:ø1.5
0 0
0.1 0.2 0.3 0.4 0.5 0.6 0.7 0.8 0.9 1 MPa 0.1 0.2 0.3 0.4 0.5 0.6 0.7 0.8 0.9 1 MPa
Supply pressure Supply pressure
2
Series VMG
Dimensions
VMG11/Piping entry: Bottom Note) Reference dimensions after installation
Rc1/4
Nozzle
156
23
B Note)
34.2 Note)
32 Note)
Width across flats 22
30 102
A 117.5
Rc, NPT, G 1/4, 3/8 S coupler plug S coupler plug One-touch fitting
mounting mounting mounting
(KK4P-02MS) (KK130P-02MS) (Series KQ2H)
VMG12/Piping entry:Top
te)
No
te)
te)
No
Rc, NPT, G 1/4, 3/8
.2
No
32
34
B
Width across flats 22
Rc1/4
Nozzle
172.5 Note)
170.8 Note)
mounting mounting mounting
C Note)
(KK4P-02MS) (KK130P-02MS) (Series KQ2H)
147
23
102
30 A 117.5
(mm) (mm)
Symbol Type Nozzle part no. Nozzle size A Note) Symbol Type Nozzle part no. Nozzle size A Note)
01 KN-R02-100 ø1 23.4 41 VMG1-08-250-100 ø2.5
Nozzle length:
02 KN-R02-150 ø1.5 23 42 VMG1-08-300-100 ø3 98
100 mm
03 Male thread
KN-R02-200 ø2 22.5 43 VMG1-08-350-100 ø3.5
04 nozzle KN-R02-250 ø2.5 22.1 44 VMG1-08-250-150 ø2.5
Nozzle length:
05 VMG1-R02-300 ø3 22 45 VMG1-08-300-150 ø3 148
150 mm
06 VMG1-R02-350 ø3.5 46 ø8 copper VMG1-08-350-150 ø3.5
21.5 extension
07 VMG1-R02-400 ø4 47 nozzle Note) VMG1-08-250-300 ø2.5
Nozzle length:
11 KNH-R02-100 ø1 48 VMG1-08-300-300 ø3 298
High efficiency 300 mm
12 nozzle
KNH-R02-150 ø1.5 44 49 VMG1-08-350-300 ø3.5
13 KNH-R02-200 ø2 50 VMG1-08-250-600 ø2.5
Nozzle length:
21 KNS-R02-075-4 ø0.75 x 4 51 VMG1-08-300-600 ø3 598
600 mm
22 Low noise nozzle KNS-R02-090-8 ø0.9 x 8 52 VMG1-08-350-600 ø3.5
12
23 with male thread KNS-R02-100-4 ø1 x 4
24 KNS-R02-110-8 ø1.1 x 8
31 Nozzle length: VMG1-06-150-300 ø1.5 (mm)
298
32 300 mm VMG1-06-200-300 ø2 Type One-touch fitting model B Note) C Note)
33 Nozzle length: VMG1-06-150-600 ø1.5 KQ2H06-02S 17 158
598 Metric size
34 ø6 copper 600 mm VMG1-06-200-600 ø2 KQ2H08-02S 20.5 161.5
extension one-touch fitting
35 nozzle Note) Nozzle length: VMG1-06-150-100 ø1.5 KQ2H10-02S 27.5 168
98
36 100 mm VMG1-06-200-100 ø2 KQ2H07-35S 17 158
Inch size
37 Nozzle length: VMG1-06-150-150 ø1.5 KQ2H09-35S 20.5 161.5
148 one-touch fitting
38 150 mm VMG1-06-200-150 ø2 KQ2H11-35S 27.5 168
Note) Reference dimensions after installation Note) Reference dimensions after installation
3
Dimensions: Nozzles/Series KN
Male thread nozzle: KN (mm)
Nozzle size Connection Width across flats
Part no.
thread L1 A∗ Connection thread
D H1
KN-R02-100 ø1 31.4 25.4
KN-R02-150 ø1.5 31 25
KN-R02-200 ø2 30.5 24.5
øD
KN-R02-250 ø2.5 R1/4 14 30.1 24.1
VMG1-R02-300 ø3 30 24 H1
A
VMG1-R02-350 ø3.5 29.5 23.5
VMG1-R02-400 ø4 29.5 23.5 L1
∗ Reference dimensions after R thread installation
øD
KNH-R02-200 ø2 H1
A
∗ Reference dimensions after R thread installation L1
øD
KNS-R02-075-4 ø0.75 x 4
KNS-R02-090-8 ø0.9 x 8
20 14 2
R1/4 14
KNS-R02-100-4 ø1 x 4 Connection
H1 A thread
KNS-R02-110-8 ø1.1 x 8
L1
∗ Reference dimensions after R thread installation
H1
diameter
Outside
L2
L
4
Series VMG
m25
VMG1m-mm-1 to 04
Width across
flats 17
m23.5
VMG1m-mm-05 to 07
ø10
P5670129-11 HNBR ø6 copper
VMG1mm-m-31 to 38
P5670129-11F Fluororubber extension nozzle
22
VMG1m-mm-31 to 38
5
Blow Gun X35
with extension and high efficiency nozzle
Series VMG
How to Order
VMG 1 1 W 02 X35 A
Piping entry
1 Bottom Nozzle
Nozzle part no. Nozzle length (D)
A 123
Body color
B 332
W White C 632
BU Dark blue
Specifications
Table 1: Piping connection type Table 2: Piping connection type
Fluid Air Part No. Port size Part No. Pipe part no.
Operating pressure range 0 to 145 psi (0 to 1.0 MPa) VMG11-02-X35 Rc1/4 VMG11-m-X35A P5670127-100-X33
VMG11-03-X35 Rc 3/8 VMG11-m-X35B P5670127-300-X33
Proof pressure 217 psi (1.5 MPa)
VMG11-N02-X35 NPR 1/4 VMG11-m-X35C P5670127-600-X33
Ambient and fluid VMG11-N03-X35 NPT 3/8
23 to 140°F (–5 to 60°C) (No freezing)
temperature
VMG11-F02-X35 G 1/4
Flow-rate characteristics C (dm3/s·bar): 6.0, b: 0.25 VMG11-F03-X35 G 3/8
(With nozzle removed) (Effective area: 0.047 inch2 (30 mm2))
Port size Refer to table 1
Piping entry Bottom
Nozzle port size Rc1/4
Weight (Main unit only) 6.35 oz (180 g)
Operational force (when
1.57 lbf (7 N)
the valve is fully open)
6
Series VMG-X35
Dimensions
S coupler plug/one-touch fitting mounting
dimensions after installation
Width across flats 22
D 7.5
ø2
7
32 Note)
14 (Hex.) 14 (Hex.)
156
KK130P-02MS
With S coupler plug With S coupler plug
VMG11-11-X53 VMG11-12-X53
X-number
B Note)
102
14 (Hex.)
117.5
KQ2H06-11 (02S, 35S)
(mm)
Type Connection size Model B
H06 17 17
Metric size
H08 20.5 20.5
one-touch fitting
H10 27.5 27.5
H07 17 17
Inch size
H09 20.5 20.5
one-touch fitting
H11 27.5 27.5
Note) Reference dimensions after installation
DHF10-02 H-10-02
156
Bill of materials
Qty 1: DHF10-02
Qty 1: H10-02
Qty: 1 VMG11BU-N02-13
Customer supplied 10mm tubing cut to length 1/4 NPT Pipe connections
RFKSS-GAP0030
Fluid Air
Operating pressure range 0 to 145 psi (0 to 1.0 MPa)
Proof pressure 217 psi (1.5 MPa)
Ambient and fluid
23 to 140°F (–5 to 60°C) (No freezing)
temperature
7
Series VMG
Specific Product Precautions 1
Be sure to read this before handling.
Selection Piping
Warning Caution
1. Check the specifications. 3. Wrapping of pipe tape
The products in this catalog are designed to be used in When screwing together pipes and fittings, etc., be certain that chips
compressed air systems only. If the products are used in an from the pipe threads and sealing material do not get inside the blow
environment where pressure or temperature is out of the specified gun. Also, when the pipe tape is used, leave 1.5 to 2 thread ridges
range, damage and/or malfunction may result. Do not use under exposed at the end of the threads.
Ex
such conditions. po Wrapping
se
ap direction
pro
Caution x.
2t
hre
ad
s. Pipe tape
1. Do not apply the blow gun to flammable, explosive or
toxic substances such as gas, fuel gas or refrigerant.
Such substances may exude from inside the blow 4. When tightening the threads, secure the nozzle holder of
gun. the blow gun by applying a wrench of 22 mm width
across flats to the two chamfered surfaces of the holder
Mounting without applying force to the body. Then, tighten the
nozzle with torque specified in the table below. As a
Warning guideline, it is equivalent to 2 to 3 additional turns with a
tool after manual tightening.
1. Install a stop valve on the supply pressure side of the Be careful that tightening with torque beyond the ranges in the table
blow gun to enable emergency shut off in case of unex- below may cause damage to the body.
pected leakage or damage.
2. When installing a nozzle on the blow gun, wrap pipe Wrench
Male thread Tightening torque lb⋅ft N⋅m
tape around the threads of the nozzle. Port
R1/4 8.9 to 10.3 (12 to 14)
3. When installing the nozzle, secure the nozzle holder of R3/8 16.2 to 17.7 (22 to 24)
the blow gun by applying a wrench of 22 mm width
across flats to the two chamfered surfaces of the
holder without applying force to the body. Then,
tighten the nozzle with force within the torque range
below. As a guideline, it is equivalent to 2 to 3
additional turns with a tool after manual tightening. 5. Allow extra length when connecting a tube to
accommodate changes in tube length due to pressure.
Wrench 6. Confirm that no twisting, turning or tensile force or
Nozzle holder moment load is applied to the port or tube. This may
cause fittings to fracture or tubes to be crushed, burst or
come loose.
7. Do not abrade, entangle or scratch the tube. This may
cause the tube to be crushed, burst or come loose.
8
Series VMG
Specific Product Precautions 2
Be sure to read this before handling.
Caution Warning
1. Install air filters. 1. To prevent lurching of the nozzle due to air pressure,
Install air filters at the upstream side of blow gun. Choose the filtration confirm that the nozzle is not loosened or rattling by
degree of 5 µm or finer. pulling it by hand before operation.
2. Install an after-cooler, air dryer or water droplet separator, 2.Make sure to wear safety goggles to protect yourself from
etc. splashed substances.
Air excessive drainage may cause a malfunction of blow gun and 3. Do not direct the tip of the nozzle at the face or other
contaminate or damage the target object. To prevent this, install an parts of a human body. It may cause danger to
after-cooler, air dryer or water droplet separator, etc. personnel.
4. Do not use the product to clean or remove toxic
Operating Environment substances or chemicals.
5. Do not drop, step on or hit the product. It may cause
Warning damage to the product.
6. Do not use the product to disturb public order or public
1. Do not use in an atmosphere of corrosive gases,
hygiene.
chemicals, sea water, water or water vapor or in an
environment where such substances may adhere. 7. This product is not a toy.
2.Provide shading in an environment where the product is 8. After blowing, make sure to hang the product on a hook,
exposed to the sunlight. etc.
If leaving the product in a dusty place, particles will enter the product
3. Do not use in an environment where a heat source is at a
and may result in a malfunction.
close distance.
4. Do not use in an environment where static electricity is a Hook
problem. It may cause malfunction or failure of the
system. Please contact SMC for use in such an
environment.
5. Do not use in an environment where spatters are
generated. There is danger of fires caused by spattering.
Please contact SMC for use in such an environment.
6. Do not use in an environment where the product is
exposed to cutting oil, lubricating oil or coolant oil.
Please contact SMC for use in an environment where the
product is exposed to such liquid as cutting oil,
lubricating oil or coolant oil.
Maintenance
9. When the blow gun is used or stored, confirm that no
Caution twisting, turning or tensile force or moment load is
applied to the port or tube. This may cause fittings to
1. In periodical inspections, check the following items and fracture or tubes to be crushed, burst or come loose.
replace the parts if necessary.
a) Scratches, gouges, abrasion, corrosion
10. When attaching a nozzle cover, align the hex parts of the
b) Air leakage nozzle and nozzle cover before covering. When attaching
c) Twisting, crushing and turning of connected tubes an extension nozzle cover, confirm that the nozzle tip is
d) Hardening, deterioration and softening of connected tubes completely inserted into the extension nozzle cover.
e) Loosening of nozzles
11. Do not use a nozzle cover or extension nozzle cover if it
2. When removing the product, first stop the pressure is cracked or does not fit securely, and replace with a
supply, exhaust compressed air in the piping and check new cover.
the condition of atmospheric release.
3.Do not disassemble or remodel the body of the product.
9
These safety instructions are intended to prevent hazardous situations and/or
Safety Instructions equipment damage. These instructions indicate the level of potential hazard with the
labels of “Caution,” “Warning” or “Danger.” They are all important notes for safety
and must be followed in addition to International Standards (ISO/IEC)∗1), and other
safety regulations.
∗1) ISO 4414: Pneumatic fluid power – General rules relating to systems.
ISO 4413: Hydraulic fluid power – General rules relating to systems.
Caution indicates a hazard with a low level of risk which,
Caution: if not avoided, could result in minor or moderate injury. IEC 60204-1: Safety of machinery – Electrical equipment of machines.
(Part 1: General requirements)
ISO 10218-1: Manipulating industrial robots - Safety.
Warning: Warning indicates a hazard with a medium level of risk
which, if not avoided, could result in death or serious injury.
etc.
Warning Caution
1. The compatibility of the product is the responsibility of the 1. The product is provided for use in manufacturing industries.
person who designs the equipment or decides its specifications. The product herein described is basically provided for peaceful use in
Since the product specified here is used under various operating conditions, its manufacturing industries.
compatibility with specific equipment must be decided by the person who designs If considering using the product in other industries, consult SMC beforehand and
the equipment or decides its specifications based on necessary analysis and test
exchange specifications or a contract if necessary.
results. The expected performance and safety assurance of the equipment will be
If anything is unclear, contact your nearest sales branch.
the responsibility of the person who has determined its compatibility with the
product. This person should also continuously review all specifications of the
product referring to its latest catalog information, with a view to giving due
consideration to any possibility of equipment failure when configuring the
Limited warranty and Disclaimer/
equipment. Compliance Requirements
2. Only personnel with appropriate training should operate machinery
The product used is subject to the following “Limited warranty and Disclaimer”
and equipment.
The product specified here may become unsafe if handled incorrectly. The and “Compliance Requirements”.
assembly, operation and maintenance of machines or equipment including our Read and accept them before using the product.
products must be performed by an operator who is appropriately trained and
experienced. Limited warranty and Disclaimer
3. Do not service or attempt to remove product and machinery/ 1. The warranty period of the product is 1 year in service or 1.5 years after
equipment until safety is confirmed. the product is delivered.∗2)
1. The inspection and maintenance of machinery/equipment should only be
Also, the product may have specified durability, running distance or
performed after measures to prevent falling or runaway of the driven objects
have been confirmed. replacement parts. Please consult your nearest sales branch.
2. When the product is to be removed, confirm that the safety measures as 2. For any failure or damage reported within the warranty period which is clearly our
mentioned above are implemented and the power from any appropriate source
responsibility, a replacement product or necessary parts will be provided.
is cut, and read and understand the specific product precautions of all relevant
products carefully. This limited warranty applies only to our product independently, and not to any
3. Before machinery/equipment is restarted, take measures to prevent other damage incurred due to the failure of the product.
unexpected operation and malfunction.
3. Prior to using SMC products, please read and understand the warranty terms
4. Contact SMC beforehand and take special consideration of safety and disclaimers noted in the specified catalog for the particular products.
measures if the product is to be used in any of the following
∗2) Vacuum pads are excluded from this 1 year warranty.
conditions. A vacuum pad is a consumable part, so it is warranted for a year after it is delivered.
1. Conditions and environments outside of the given specifications, or use Also, even within the warranty period, the wear of a product due to the use of the vacuum pad
outdoors or in a place exposed to direct sunlight. or failure due to the deterioration of rubber material are not covered by the limited warranty.
2. Installation on equipment in conjunction with atomic energy, railways, air
navigation, space, shipping, vehicles, military, medical treatment, combustion
and recreation, or equipment in contact with food and beverages, emergency Compliance Requirements
stop circuits, clutch and brake circuits in press applications, safety equipment 1. The use of SMC products with production equipment for the manufacture of
or other applications unsuitable for the standard specifications described in the
product catalog. weapons of mass destruction (WMD) or any other weapon is strictly prohibited.
3. An application which could have negative effects on people, property, or 2. The exports of SMC products or technology from one country to another are
animals requiring special safety analysis. governed by the relevant security laws and regulations of the countries involved
4. Use in an interlock circuit, which requires the provision of double interlock for
in the transaction. Prior to the shipment of a SMC product to another country,
possible failure by using a mechanical protective function, and periodical
checks to confirm proper operation. assure that all local rules governing that export are known and followed.
Edition B O Related products KK/KKH series S coupler, changed to the model Edition F O Added ø3, ø3.5, ø4 to male thread nozzle.
Revision history
change products. O With cover is added to male thread nozzle and extension nozzle.
O High efficiency nozzle data listed. JR O Added outside diameter ø8 to copper extension nozzle.
O Added 100 mm and 150 mm lengths to copper extension nozzle.
Edition C O Best Pneumatics No.1 (Pages 1889 to 1899) extracted. NS
O Number of pages from 12 to 16. QR
Edition D O Added the KK130 series S coupler and one-touch fitting type.
O Number of pages from 16 to 12. OO
Edition E O Not available
Safety Instructions Be sure to read “Handling Precautions for SMC Products” (M-E03-3) before using.
10
Global Manufacturing, Distribution and Service Network
Worldwide Subsidiaries
America
North & South America Asia/Oceania Europe/Africa
U.S.A. SMC Corporation of America SRI LANKA (Distributor) Electro-Serv(Pvt.)Ltd. CZECH REPUBLIC SMC Industrial Automation CZ s.r.o.
CANADA SMC Pneumatics (Canada) Ltd. IRAN (Distributor) Abzarchian Co. Ltd. HUNGARY SMC Hungary Ipari Automatizálási Kft.
MEXICO SMC Corporation(México), S.A. de C.V. U.A.E. (Distributor) Machinery People Trading Co. L.L.C. POLAND SMC Industrial Automation Polska Sp. z o.o.
BRAZIL SMC Pneumãticos do Brasil Ltda. KUWAIT (Distributor) Esco Kuwait Equip & Petroleum App. Est. SLOVAKIA SMC Priemyselná Automatizácia Spol s.r.o.
CHILE SMC Pneumatics (Chile) S.A. SAUDI ARABIA (Distributor) Assaggaff Trading Est. SLOVENIA SMC Industrijska Avtomatika d.o.o.
COLOMBIA SMC Colombia Sucursal de SMC Chile S.A. BAHRAIN (Distributor) BULGARIA SMC Industrial Automation Bulgaria EOOD
Mohammed Jalal & Sons W.L.L. Technical & Automative Services
ARGENTINA SMC Argentina S.A. CROATIA SMC Industrijska Automatika d.o.o.
SYRIA (Distributor) Miak Corporation
BOLIVIA SMC Pneumatics Bolivia S.r.l. BOSNIA AND HERZEGOVINA(Distributor) A.M. Pneumatik d.o.o.
JORDAN (Distributor) Atafawok Trading Est.
VENEZUELA SMC Neumatica Venezuela S.A. SERBIA(Distributor) Best Pneumatics d.o.o.
BANGLADESH (Distributor) Chemie International
PERU (Distributor) IMPECO Automatización Industrial S.A.C. UKRAINE(Distributor) PNEUMOTEC Corp.
AUSTRALIA SMC Pneumatics(Australia)Pty.Ltd.
ECUADOR (Distributor) ASSISTECH CIA. LTDA. FINLAND SMC Pneumatics Finland Oy
NEW ZEALAND SMC Pneumatics(N.Z.)Ltd.
NORWAY SMC Pneumatics Norway AS
Asia/Oceania JAPAN SMC Corporation
SWEDEN SMC Pneumatics Sweden AB
CHINA SMC(China)Co.,Ltd.
ESTONIA SMC Pneumatics Estonia Oü
CHINA SMC Pneumatics (Guangzhou) Ltd. Europe/Africa
LATVIA SMC Pneumatics Latvia SIA
HONG KONG SMC Pneumatics(Hong Kong)Ltd. GERMANY SMC Pneumatik GmbH
LITHUANIA(LIETUVA) UAB “SMC Pneumatics”
TAIWAN SMC Pneumatics(Taiwan)Co.,Ltd. SWITZERLAND SMC Pneumatik AG
ROMANIA SMC Romania S.r.l.
KOREA SMC Pneumatics Korea Co., Ltd. U.K. SMC Pneumatics (U.K.) Ltd.
RUSSIA SMC Pneumatik LLC.
SINGAPORE SMC Pneumatics(S.E.A.)Pte.Ltd. FRANCE SMC Pneumatique SA
KAZAKHSTAN SMC Kazakhstan, LLC.
MALAYSIA SMC Pneumatics(S.E.A.)Sdn.Bhd. SPAIN / PORTUGAL SMC España S.A.
TURKEY (Distributor) Entek Pnömatik Sanayi ve. Ticaret Şirketi
THAILAND SMC (Thailand) Ltd. ITALY SMC Italia S.p.A.
MOROCCO (Distributor) Soraflex
PHILIPPINES Shoketsu SMC Corporation GREECE SMC HELLAS E.P.E
TUNISIA (Distributor) Byms
INDIA SMC Pneumatics(India)Pvt.Ltd. IRELAND SMC Pneumatics (Ireland) Ltd.
EGYPT (Distributor) Saadani Trading & Industrial Services
ISRAEL (Distributor) Baccara Geva A.C.S. Ltd. NETHERLANDS (Associated company) SMC Pneumatics BV
NIGERIA (Distributor) Faraday Engineering Company Ltd.
INDONESIA (Distributor) PT. Sinar Mutiara Cemerlang BELGIUM (Associated company) SMC Pneumatics N.V./S.A.
SOUTH AFRICA (Distributor) Hyflo Southern Africa (Pty.) Ltd.
VIETNAM (Distributor) Dy Dan Trading Co.,Ltd. DENMARK SMC Pneumatik A/S
PAKISTAN (Distributor) Jubilee Corporation AUSTRIA SMC Pneumatik GmbH (Austria)
WEST EAST
Austin Atlanta
Dallas Birmingham
Los Angeles Boston
Phoenix Charlotte
Vancouver
Portland Nashville
San Francisco New Jersey Montreal
Vancouver Toronto
Richmond
Detroit
Rochester Boston
Tampa Chicago
CENTRAL
Chicago Montreal
Livermore
Cincinnati Indianapolis
Cleveland
Detroit
Atlanta
Indianapolis
Milwaukee
Sales Branches
Minneapolis
Regional Distribution Centers
St. Louis Austin
Central warehouse
Toronto
Windsor
SMC Corporation of America
10100 SMC Blvd., Noblesville, IN 46060
www.smcusa.com
SMC Pneumatics (Canada) Ltd.
www.smcpneumatics.ca