Professional Documents
Culture Documents
MORE STARS
MORE SAVINGS
POWER SAVINGS
GUIDE
AIR CONDITIONERS
The unit displayed is for representational purposes only. Actual unit may vary.
Dear customer
G. Sundar
Chief Executive Officer
IMPORTANT :
Please read this owner’s manual carefully and thoroughly
before installing and operating your room air conditioners.
Please retain this owner’s manual for future reference after
reading it thoroughly.
CONTENTS
Salient Features 1
Inside Overview 2
Indoor Unit Display 3
Remote Overview 4
Operations 5
General Instructions for Installation 12
Installation Sketch 15
Installation of Model 16
Take care of your Air Conditioner 19
Precautions to be taken 20
Trouble Shooting 21
Installation and Satisfaction Report 23
Warranty Terms & Conditions 25
Preventive Maintenance Service Coupon 27
Warranty Card(Customer Copy) 29
Warranty Card(service Centre Copy) 31
SALIENT FEATURES
• Aesthetics:-
a) Unique Power Flat Panel
• Performance:-
a) Imported High BTU Tropicalised Compressor
b) Trapezoidal Inner Grooved Tube
c) Large L-Shaped Condenser Coil
d) High RPM Fan Motor with High Static
e) High Technology 5 Star / 3 Star Energy Efficient.
• Features:-
a) Multi-Step Air Swing for Customized Cooling.
b) Auto-Restart
c) i-Cool
1
INSIDE OVERVIEW INDOOR UNIT DISPLAY
-cool
-cool
n OUTDOOR UNIT
Cool Mode Temp display Auto Mode
Air in
Set Timer Mode I-Cool
Connection
pipe and
connecting wire
Exhaust Air
2 3
REMOTE OVERVIEW OPERATIONS
4 5
OPERATIONS OPERATIONS
Your split AC operates in one of four modes, AUTO-COOL-DRY-FAN. The modes button The FAN Mode:
cyclically chooses between these operating modes. 1. Press "MODE" button to cyclically step through the COOL, FAN, DRY & AUTO modes and
The AUTO Mode : stop when FAN mode is selected.
1. Press "MODE" button to cyclically step through the AUTO-COOL-DRY-FAN modes and stop 2. symbol can be seen toward FAN word on the Remote panel when you select the FAN
when AUTO mode is selected. mode.
2. symbol can be seen toward AUTO word on the Remote panel when you select the AUTO 3. In FAN mode, only Indoor FAN will run at set speed and Compressor & Outdoor Fan will
mode. remain off. Temperature display will goes off.
3. In this mode, the fan speed is set to AUTO by default. 4. In this mode, you can change the Indoor FAN Speed, but you can not set the desired TEMP.
4. Temperature can be set in this mode.
5. In the AUTO mode, your AIR CONDITIONER "Thinks” for you. TIMER Operation:
The unit automatically and continuously monitors the difference between room temp. and You can program your split AC to switch itself ON or OFF at particular time.
set temp. and adjusts the fan speed accordingly, to ensure maximum comfort. Maximum set time is 24 hrs, with 0.5 & 1.0 hr increment .
The COOL mode:
In the cool mode, the compressor is in operation and your AC functions in the standard ON TIMER:
operating mode, cooling your room to the desired set temp. When the AC is "OFF" (in standby), press "TIMER" Button on remote to use this feature as the
1. Press "MODE" button to cyclically step through the AUTO-COOL-DRY-FAN modes and TIMER. (make sure that MCB switch is "ON". The "TIMER" light on Indoor unit will glow ON.
stop when cool mode is selected. For EXAMPLE:
2. symbol can be seen toward COOL word on the Remote panel when you select the cool Suppose you want to switch ON the AC after 8 hrs. Press "TIMER" button, when AC is in OFF
mode. condition. Press Temp. Up & Down key to set time delay.
In this mode, you can change the temp. settings by pressing " " and “ ” temp. buttons. Press "TIMER" button to set on timer. Display on Remote will show "8HR”.
You can change the fan speed setting by pressing FAN button.
3. If the Room temp. is more than the set temp., then the compressor & outdoor FAN will OFF TIMER:
remain ON and perform the Cooling operation. If the room temp. achieves the temp. less When the AC is "ON", press "TIMER" Button on remote to use this feature as
than set temp., then the compressor & outdoor FAN will remain OFF. the TIMER. The "TIMER" light on Indoor unit will glow ON.
The DRY Mode: For EXAMPLE:
In the DRY mode, your AC reduces the humidity within the room faster. Suppose you want to switch OFF the AC after 8 hrs. Press "TIMER" button, when AC is in ON
When the room temp. is more than 17OC then only the DRY mode operates. condition. Press Temp. Up & Down key to set time delay.
1. Press "MODE" button to cyclically step through the AUTO-COOL-DRY-FAN modes and Press "TIMER" button to set OFF timer. Display on Remote will show "8HR”.
stop when DRY mode is selected.
2. symbol can be seen toward DRY word on the Remote panel when you select the DRY NOTE: Upto 10 hrs, setting time increment will be 0.5 hrs, after 10 hrs setting time increment
mode. will be 1 hrs.
3. In DRY mode, Indoor FAN will run at low speed, Compressor & Outdoor Fan will remain CANCEL TIMER:
ON. If you want to cancel the Timer either TIMER ON or TIMER OFF, press the corresponding TIMER
4. In this mode, No fan speed indicator display and you can not change the FAN Speed, but button and set the time to 0:0.
you can set the desired TEMP.
6 7
OPERATIONS OPERATIONS
Turbo MODE:
i-Cool (With Ceiling Fan Controller):- Pressing Turbo key on remote, remote will display symbol “ “ against TURBO and activates
the Turbo function and air conditioner goes to powerful cooling. During this Mode temperature
One touch auto cooling control of AC & Ceiling Fan*. and fan speed cannot be changed.
When you press i-cool button on remote, -cool light will be glows on Indoor unit. In this mode the AC works on a preset temperature of 18 degree centigrade at high fan speed.
Compressor will start immediately in this mode and will continue to operate till set temperature is
This mode is activated by pressing i-cool key on remote. To enable mode to control Ceiling
achieved .Thereafter it will work in cyclical ON/OFF mode to keep the room temperature within 2
Fan also, main switch of Ceiling Fan has to be in ON position.
degree of set temperature. Press again to cancel this operation. The unit will run in COOL Mode.
In this mode initially the AC & Ceiling Fan start in special mode at super high speed
designed to give instant cooling and comfort. Compressor will start immediately in this Energy Saver MODE:
mode. After some time the AC and Ceiling Fan work at special mode which gives powerful Pressing Energy Saver key on remote activates Energy Saver function to keep room normal
cooling along with energy savings. During this mode the speed of AC Fan and ceiling fan temperature by reducing compressor run hours to get more savings.
changes automatically with time and temperature change. Set temperature also changes
In this mode the AC works on a preset temperature of 25 degree centigrade at selectable fan
automatically. During this operation both AC and Ceiling Fan are coordinated to ensure
speed. Compressor will work in cyclical ON/OFF mode to keep the room temperature within 2
speed cooling with energy savings. While AC is in this mode temp, Fan Speed, Timer,
degree of set temperature.
Sleep keys are inactive and these parameters cannot be changed.
In this mode temperature cannot be changed & Fan speed can be changed.
To quit i-cool mode Press MODE or TURBO or Energy Saver Button. Press again to cancel this operation. The unit will run in COOL Mode.
i-Cool (Without Ceiling Fan Controller):- Ceiling Fan Manual Operation – only when optional i-cool ceiling fan controller
is installed:
In case i-cool ceiling fan controller which is an optional accessory has not been installed, Ceiling fan speed can be controlled only through AC remote control as all other manual
the AC will work in special i-cool mode on pressing i-cool key on remote. In this mode controllers are bypassed while installing i-cool fan controller.
initially the AC work start at super high speed designed to give instant cooling and When AC is in any mode other then i-cool mode, Ceiling fan speed can be controlled using
comfort. Compressor will start immediately in this mode. (Fan noise will be higher during remote control. To enable this Ceiling fan mains have to be in ON position. Press C.F. ON/OFF
this period due to higher air throw).After some time the AC will work at special mode which key on remote to start ceiling fan. Ceiling fan speeds can be changed by pressing C.F. + key
gives powerful cooling along with energy savings. During this mode the speed of AC Fan on remote to increase and C.F . – key on remote to decrease. The speeds can be varied by 5
speed changes automatically with time and temperature change. Set temperature also steps by pressing C.F. + and C.F. – keys on remote. Press C.F. ON/OFF key on remote to switch
changes automatically. While AC is in this mode temp, Fan Speed, Timer, Sleep keys are off ceiling fan.
inactive and these parameters cannot be changed. To quit i-cool mode Press MODE or
TURBO or Energy Saver Button.
* i-cool Ceiling Fan Controller is an optional accessory and is not part of the AC . Cost of
i-cool ceiling fan controller and its installation is extra and not included in the AC.
8 9
OPERATIONS OPERATIONS
LOCK Button: Push this button to lock in all the current settings. To release settings, push Emergency Operation Switch:
again.(Use a 1mm little round stick to push this button). In case the batteries in the remote are worn out, or remote is faulty or missing, use
emergency operation switch (*) to ON/OFF AC.
Every time the switch is pressed, it changes in sequence of AUTO - COOL - STOP.
In Emergency operation mode the set temperature will be 24OC, Fan speed will be Auto.
To access emergency switch, open the grill as
shown in the figure.
10 11
GENERAL INSTRUCTIONS FOR GENERAL INSTRUCTIONS FOR
INSTALLATION INSTALLATION
Locating the indoor and outdoor units Locating the Outdoor Unit
properly will help optimise the performance of The outdoor unit houses the compressor,
your airconditioner. While your Onida / condenser fan and electrical components.
Dealer's Technician will be happy to guide you The heat removed from the room is expelled
on the best location for your airconditioner,
to the atmosphere through the outdoor unit.
here are a few helpful hints.
Once again, the Onida / dealer's Technician
will ensure optimal installation of the ODU for
Locating the Indoor Unit
you. However, the following information will
• Locate the IDU for the best cool air be of interest to you.
circulation. Preferably, there should be
no obstructions nearby, as shown in the • The Outdoor Unit can be mounted on a
adjacent figure. wall, sunshade or skirting.
• All indoor units will form condensate water. • Ensure that air can pass freely through
Please ensure that the condensate can the unit. Please allow at least 2 meters
be drained out of the room to a toilet / free space on the air outlet side, and 0.3
pantry, etc. The installation engineer will meters on the air inlet side.
make sure that a "U" bend is provided in
the drain to prevent insects from coming
into the room through the drain tube, as
shown in the adjacent figure.
• If more than one ODU is to be installed,
they must be properly separated, so that
the warm air from the outlet of one does
not enter the inlet of the other.
12 13
GENERAL INSTRUCTIONS FOR
INSTALLATION INSTALLATION SKETCH
• Too high
supported adequately.
S.No. Name of Accessories Q’ty
• Finally, it is most important for the 1 Installation Plate 1 Additional drain pipe
ODU to be easily accessible to the 2 Clip Anchor 8
3 Self-tapping Screw A ST3.9X25 8
service engineer. It is advisable to 4 Seal 1
5 Drain Joint 1
discuss the same with the engineer 6.35 (9000Btu/h, 12000Btu/h,
Liquid Side Parts you
before deciding upon the location of Connecting
Pipe
18000Btu/h Models)
must
6 Gas Side 9.53 (9000Btu/h Model) Purchase
the unit. Assembly
Gas Side 12.7 (12000Btu/h,18000Btu/h)
7 Remote Controller 1
If the ODU is to be located on a high 8 Self-tapping Screw B ST3.9X10 2
9 Remote Controller Holder 1
ledge, adequate space must be
60cm above
provided for the service engineer to Wrapping tape
service the unit. It is a good idea to
provide a catwalk (a platform) 30c
around the unit and access door / To A mab
ove Air Outlet
ODU
window to the Unit. ODU bov
e
To ma
30c
Remote Controller
Electrical outlet
MCB 7 Mounting screw B e
bov Loop the
cma
SET TEMPERATURE( C)
HEALTH
ST2.9x10-C-H
AUTO
STABILISER ADJUST
9 B cable.
60c
indoor unit is finalised, you must provide MODE
SWING
ON/OFF FAN SPEED
SLEEP TIMER ON
8
ma
bov
CLEAR
AIR RESET LOCK TIMER OFF
e
a suitable electrical outlet near the
AUTO FOLLOW LED
C
CLEAN ME DISPLAY TURBO
Remote controller
holder
indoor unit.
14 15
INSTALLATION INSTALLATION
is to be installed.
n Installation of outdoor unit
2. Drill two holes at a distance of 450 mm between them for the expansion bolts.
150mm or more to ceiling
Installation plate
Indoor unit outline
120mm or more
to wall 120mm or more
45 to wall
293
90 1 2(N)
45
pipe hole 65 pipe hole 65
995
10 18 • The electric box cover must be mounted on its position on outdoor unit.
Gas side
piping insulation Liquid side
piping insulation
Mounting Board air proof with putty
Water
Finally wrap it
drainage
with tape
pipe
16 17
INSTALLATION TAKE CARE OF YOUR
AIR CONDITIONER
the length of connecting pipe (m) 7 8 9 10 • Lift the filters slightly upwards
n Test
• Proceed leak test (with leak detector or soap water.) and inspect connecting
cables before test operation.
Test procedure: (Control by emergency operation switch or remote • Do not use detergents for cleaning
controller) For detailed operation, see OPERATION OF AIR CONDITIONER the filter.
in the manual.
18 19
PRECAUTIONS TO BE TAKEN TROUBLE SHOOTING CHART
Note: If the unit still does not work, or if any other types of symptoms are encountered,
shut off the mains (switch fuse unit) and call the service engineer.
20 21
INSTALLATION & SATISFACTION
REPORT
Customer Name :
Address
Phone[O] [R]
22 23
WARRANTY TERMS
AND CONDITIONS
M/S. MIRC ELECTRONICS LTD, WARRANTS THIS ONIDA AIR CONDITIONER[(except the front grill,
knobs, remote unit and add-on plastic parts) TO THE ORIGINAL PURCHASER TO BE FREE FROM
DEFECTS IN MATERIALS AND WORKMANSHIP WITHIN ONE YEAR FROM THE DATE OF PURCHASE
AS PROVIDED IN THE WARRANTY REGISTERATION CARD.
24 25
Preventive Maintenance Service
Customer Identification
8. It shall be the absolute discretion of the company to a) effect the repairs or replacement of parts Number:
whether at the site of installation or at any service centre, and b) have the job attended to either by the Preventive Maintenance Service 1 Date: ________
Company's service personnel or its authorised dealer ______________________
Customer Identification Number: ___________________________________________
9. This warranty is in the nature of and for the purpose of set forth herein above and in particular the
Unit Model: ___________ Name of the customer: ____________________________________________________
Company shall not in any event be liable for direct, indirect, incidental or consequential loss or
damages to either the said purchaser and /or his property or any other third party. Installation address: ______________________________________________________
Sr. No: _______________
10. The AC is designed to operate at a range (230V +/- 10%). Any failure due to operation of the machine ________________________________________________________________________
beyond these limits will not be covered by the above warranty. Name of Serviceman:
________________________________________________________________________
Customer shall ensure that a stabilizer is installed in those areas where voltage is not available within ______________________ Phone: _________________ Mobile: __________________ Fax: ________________
the warranty range (230V +/- 10%). The stabilizer should be of any reputed manufacturer, tested and
recommended by the Company. Date: ______ Time: _____ E-mail: _________________________________________________________________
11. The purchaser should preserve the original invoice for necessary verification and produce, as and Unit model: ____________________________ Serial Number: __________________
when required. Service report number: ___________________________________________________
12. Warranty null and void if: Sign. of Serviceman
i. The Air Conditioner is not purchased from the authorized dealers of the company. Customer's Signature: _______________________ Name: _______________________
ii. The Service Centre copy of warranty card is not received within 10days of date of purchase at the
nearest Authorised Service Centre.
iii. Any damage is caused by accident, mishandling, tampering with installation, or negligence in
following instructions of the user manual issued by Company.
iv. Any damage is caused by improper electrical circuit outside the unit or by any defective electrical
supply Preventive Maintenance Service
Customer Identification
v. At any time, during the warranty period if any part of the unit is tampered with, altered, repaired or Number:
serviced by any unauthorized person, not being the authorized representative of the company or Preventive Maintenance Service 2 Date: ________
its authorized dealers ______________________
Customer Identification Number: ___________________________________________
vi. The serail number of the unit or any part thereof is damaged , defaced, altered, obliterated , or
Unit Model: ___________ Name of the customer: ____________________________________________________
tampered with or removal for any reason whatsoever
viii. The unit is unauthorisedly moved from its original place of installation or re-installation Sr. No: _______________ Installation address: ______________________________________________________
13. None of the employees and /or Authorized Dealers of the Company have any authority whatsoever to ________________________________________________________________________
Name of Serviceman:
vary the terms and conditions of this warranty. ________________________________________________________________________
14. This warranty shall be deemed to have been issued at Mumbai, state of Maharashtra and courts at ______________________ Phone: _________________ Mobile: __________________ Fax: ________________
Mumbai shall have exclusive jurisdiction on matters covered by or following from this warranty, and
Date: ______ Time: _____ E-mail: _________________________________________________________________
the original purchaser alone shall have cause of action arising out of the transaction.
Unit model: ____________________________ Serial Number: __________________
Service report number: ___________________________________________________
Sign. of Serviceman
Customer's Signature: _______________________ Name: _______________________
26 27
MIRC Electronics Limited
Serial No. Warranty Card
Customer Copy
Customer Details
Residence Address:
Dist: Pin:
State: Occupation:
Product Details
Please Tick The Appropriate Product Colour TV B&W TV DVD Washing M/C. AC Plasma TV Rear Projection TV
Purchase Date
Day Month Year
Signature
Bill No.
Thank you for selecting a World Class product and we assure you that it will perform as per your expectations
We thank you for taking your time to complete this form. All Information Provided by You will be Kept Confidential.
(Please Fill In, Tear off, Fold and Mail this form to Reach us within 10 days of the Product Purchase.)
We welcome your Valuable Suggestions, if any, to Improve our Products and Services :
Customer Code:
Branch:
Residence Address:
Dist: Pin:
State: Occupation:
Product Details
Please Tick The Appropriate Product Colour TV B&W TV DVD Washing M/C. AC Plasma TV Rear Projection TV
Purchase Date
Day Month Year
Signature
Bill No.
Thank you for selecting a World Class product and we assure you that it will perform as per your expectations
We thank you for taking your time to complete this form. All Information Provided by You will be Kept Confidential.
(Please Fill In, Tear off, Fold and Mail this form to Reach us within 10 days of the Product Purchase.)
We welcome your Valuable Suggestions, if any, to Improve our Products and Services :
Customer Code:
Branch: