11.22 For the system in Fig. 11.26, compute the pressure at the
inlet to the pump. The filter has a resistance coefficient of
1.85 based on the velocity head in the suction line.
oP ae
[#408 —>je ————_ L308
Ton
[orm 20%
Foor
‘caecor Fon
‘ak SS rter FE
I Fal open
salve
in Scoiale 40 ee
el pipe
ceioon
11.23. For the system in Fig. 11.26, compute the total head on the
pump and the power delivered by the pump to the coolant.
11.24 For the system in Fig. 11.26, specify the size of Schedule
40 steel pipe required to return the fluid to the machines.
Machine 1 requires 20 gal/minand Machine? requires 10 gal/
min, The fluid leaves the pipes at the machines at 0 psig.
124E Por el sistema de cuberia ramificada que se mucstra em
la figura 12.8, fluyen por una tuberfa de 8 pulgadas
1350 gal/min de benceno (sg = 0.87) a 140°F. Caleulle
el flujo volumétrico en las tuberias de 6 y 2 pulgadas.
Todas las tuberfas son de accro estindar cédula 40.
12.5M Un tubo de 150 nm s¢ ramifica ew dos, ine ce 100 rane
yoire de SO mm, como se aprecia en la figura 12.9. Arte
‘bos tubos son de cobse y miden JO m de longitud. (8
‘fluido es gua w 10°C.) Determine cudl debe ser el coe:
‘ficiente de resistencia K de la vdivula, con ef fin de
‘obtener ef misme fluja volumetrice de 500 L/min em
cada rama.11,31 Water at 10°C is being delivered to a tank on the roof of
a building, as shown in Fig. 11.29. The elbow is standard.
What pressure must exist at point A for 200 L/min to be
delivered?
Problems 12.4 , postive Swingape
e ‘check valve Bin
Sin
soo
lin
12.6E En el sistema de Ia figura 12.10, ta presidn en el punto
A se manticne constante a 20 psig. El flujo volumétri-
co total ea el punto B de la tuberia depende de cudies
vélwulas estén abiertas o cerradas. Para cada codo uti-
lice K = 0.9, pero ignore lis pérdidas de energia en las
tes, Asimismo, debido a quie la longitud de cada ranna es
corta, ignore las pérdidas por friccién en la tuberia, La
tuherfa en la rama I tiene un didmetro interno de 2 pul-
‘gadas y Ia rama 2 tiene otro de 4 pulgadas, Calcule el
flujo volumétrico del agua para cada una de las con-
diciones siguientes:
& Ambas villvulas ablertas,
b. Sélo estd abierta Ia vilvuila de ta roma 2
¢ Slo estd abierta Ja valvula de la rama 1.
11.32 If the pressure at point A in Fig. 11.29 is 300 kPa, compute
the volume flow rate of water at 10°C delivered to the tank.
11.33 Change the design of the system in Fig, 11.29 to replace
the globe valve with a fully open gate valve. Then, if the
Pressure at point A is 300 kPa, compute the volume flow
rate of water at 10°C delivered to the tank. Compare the
result with that of Problem 11.32 to demonstrate the
effect of the valve change.FIGURE 11.29 Problems 11.31-11.33.
Problem 12.5. oo-mm op — Valve
xasmm Ka?
160-smm OD x 5 5-mum wal
160-mm OD x 5.-mam wall
‘All flow elements ae
s0.mm OD x SPPTHE
15mm wal
Problem 12.6 D,=24n Schedule 40
Branch |
K=5 forgpen valve .
Branch 2
Dy =n Schedule 40
HSE: Por una tuberia de acero de 4 pulpadas eédula 80, de
25 pies de longitud, fluye agua a 100 “F, Calcule el flujo
i . si la pérdida de ener
gla debido a la friccién en Ia tuberia ha de limitarse a
430 piies-Ibvb,11.14M Por el sistema de la figura 11.19 fluye keroseno a 25 °C.
La longitu total del tubo de cobre de 2 pulgadas tipo
K es de 30 m. Las dow vweltas « 90" tienen un radio de
300 mm. Calcule el flujo volumétrico en ef tanque B, si
ve mantiene una presién de 150 kPa sobre el keroseno
en el rangue A.