You are on page 1of 5

Technical Data Sheet

Approved 2921;2400;2401 1 2400 epoxy ^(ValidationDate) 1

Penguard Express

Product description
This is a two component amine cured epoxy coating. It is a fast drying, high solids, high build product. Specially
designed for new construction where fast dry to handle and over coating times are required. Can be used as
primer, mid coat, finish coat or as single coat system in atmospheric environments. Suitable for properly
prepared carbon steel, aluminium, concrete and galvanised steel substrates. It can be applied at sub zero
surface temperatures.

Typical use
Suitable for structural steel and piping to be exposed to highly corrosive environments, C5I or C5M (ISO
12944-2). Recommended for offshore environments, refineries, power plants, bridges, buildings and mining
equipment.
Other

Approvals and certificates


Pre-qualification testing in accordance with NORSOK M-501, Rev. 5, System 1, suitable for exterior exposure in
offshore environment, below 120 °C.
Tested in accordance with ISO 12944-5, C5-High environment

When used as part of an approved scheme, this material has the following certification:
- Low Flame Spread in accordance with EU Directive for Marine Equipment. Approved in accordance with parts 5
and 2 of Annex 1 of IMO 2010 FTP Code, or Parts 5 and 2 of Annex 1 of IMO FTPC when in compliance with
IMO 2010 FTP Code Ch. 8

Consult your Jotun representative for details.


Additional certificates and approvals may be available on request.

Other variants available


Penguard Express MIO
Penguard Express ZP
Penguard Express CF
Refer to separate TDS for each variant.

Colours
grey, grey XO, red, buff, light red

Product data
Property Test/Standard Description
Solids by volume ISO 3233 74 ± 2 %
Gloss level (GU 60 °) ISO 2813 matt (0-35)
Flash point ISO 3679 Method 1 32 °C
Density calculated 1,6 kg/l
VOC-US/Hong Kong US EPA method 24 (tested) 260 g/l
VOC-EU IED (2010/75/EU) (calculated) 264 g/l
VOC-China GB/T 23985-2009 (ISO 11890-1) (tested) 274 g/l

The provided data is typical for factory produced products, subject to slight variation depending on colour.

Date of issue: 8 November 2016 Page: 1/5

This Technical Data Sheet supersedes those previously issued.


The Technical Data Sheet (TDS) is recommended to be read in conjunction with the Safety Data Sheet (SDS) and the
Application Guide (AG) for this product. For your nearest local Jotun office, please visit our website at www.jotun.com
Technical Data Sheet
Penguard Express

All data is valid for mixed paint.


Gloss description: According to Jotun Performance Coatings' definition.

Film thickness per coat


Typical recommended specification range

Dry film thickness 75 - 250 μm


Wet film thickness 100 - 340 μm
Theoretical spreading rate 9,9 - 3 m²/l

Surface preparation
To secure lasting adhesion to the subsequent product all surfaces shall be clean, dry and free from any
contamination.

Surface preparation summary table

Surface preparation

Substrate Minimum Recommended

Carbon steel St 2 (ISO 8501-1) Sa 2½ (ISO 8501-1)

Galvanised steel The surface shall be clean, dry and Light brush blasting using non-
appear with a rough and dull profile. metallic abrasive leaving a clean,
rough and even pattern.
Aluminium The surface shall be hand or machine Abrasive blast cleaning to achieve a
abraded with non-metallic abrasives surface profile using approved non-
or bonded fibre machine or hand metallic abrasive media which is
abrasive pads to impart a scratch suitable to achieve a sharp and
pattern to the surface and to remove angular surface profile.
all polish from the surface.
Shop primed steel Dry, clean and approved inorganic Abrasive swept or alternatively
zinc shopprimer. blasted to Sa 2 (ISO 8501-1) of at
least 70 % of the surface.
Coated surfaces Clean, dry and undamaged compatible Clean, dry and undamaged compatible
coating (ISO 12944-4 6.1) coating (ISO 12944-4 6.1)
Concrete Minimum 4 weeks curing. Moisture Minimum 4 weeks curing. Moisture
content maximum 5 %. Mechanically content maximum 5 %. Prepare the
prepare the existing concrete surface surface by means of enclosed blast
by scabbling, needle gun, mechanical shot or diamond grinding and other
disc grinding. appropriate means to abrade the
surrounding concrete and to remove
laitance.

Application
Application methods
The product can be applied by

Spray: Use airless spray.

Date of issue: 8 November 2016 Page: 2/5

This Technical Data Sheet supersedes those previously issued.


The Technical Data Sheet (TDS) is recommended to be read in conjunction with the Safety Data Sheet (SDS) and the
Application Guide (AG) for this product. For your nearest local Jotun office, please visit our website at www.jotun.com
Technical Data Sheet
Penguard Express

Brush: Recommended for stripe coating and small areas. Care must be taken to achieve the
specified dry film thickness.

Product mixing ratio (by volume)

Penguard Express Comp A 4 part(s)


Penguard Express Comp B 1 part(s)

Thinner/Cleaning solvent
Thinner: Jotun Thinner No. 17

Guiding data for airless spray


Nozzle tip (inch/1000): 17-23

Pressure at nozzle (minimum): 150 bar/2100 psi

Drying and Curing time


Substrate temperature -5 °C 0 °C 5 °C 10 °C 23 °C 40 °C

Surface (touch) dry 16 h 11 h 4h 2 h 1 h 30 min


Walk-on-dry 38 h 24 h 10 h 6 h 3 h 2h
Dry to over coat, minimum 24 h 14 h 8h 4 h 2 h 1h
Dried/cured for service 21 d 13 d 8 d 4 d 3d

Drying and curing times are determined under controlled temperatures and relative humidity below 85 %, and
at average of the DFT range for the product.

Surface (touch) dry: The state of drying when slight pressure with a finger does not leave an imprint or reveal
tackiness.

Walk-on-dry: Minimum time before the coating can tolerate normal foot traffic without permanent marks,
imprints or other physical damage.

Dry to over coat, minimum: The shortest time allowed before the next coat can be applied.

Dried/cured for service: Minimum time before the coating can be permanently exposed to the intended
environment/medium.

Induction time and Pot life


Paint temperature 23 °C

Pot life 2h

Date of issue: 8 November 2016 Page: 3/5

This Technical Data Sheet supersedes those previously issued.


The Technical Data Sheet (TDS) is recommended to be read in conjunction with the Safety Data Sheet (SDS) and the
Application Guide (AG) for this product. For your nearest local Jotun office, please visit our website at www.jotun.com
Technical Data Sheet
Penguard Express

Heat resistance
Temperature
Continuous Peak
Dry, atmospheric 120 °C 140 °C

Peak temperature duration max. 1 hour.


The temperatures listed relate to retention of protective properties. Aesthetic properties may suffer at these
temperatures.

Product compatibility
Depending on the actual exposure of the coating system, various primers and topcoats can be used in
combination with this product. Some examples are shown below. Contact Jotun for specific system
recommendation.

Previous coat: inorganic zinc silicate shop primer, epoxy, epoxy mastic, zinc epoxy, zinc silicate,
organic shop primer
Subsequent coat: acrylic, epoxy, polyurethane, polysiloxane

Packaging (typical)
Volume Size of containers
(litres) (litres)

Penguard Express Comp A 4/16 5/20


Penguard Express Comp B 1/4 1/5

The volume stated is for factory made colours. Note that local variants in pack size and filled volumes can vary
due to local regulations.

Storage
The product must be stored in accordance with national regulations. Keep the containers in a dry, cool, well
ventilated space and away from sources of heat and ignition. Containers must be kept tightly closed. Handle
with care.

Shelf life at 23 °C
Penguard Express Comp A 24 month(s)
Penguard Express Comp B 24 month(s)

In some markets commercial shelf life can be dictated shorter by local legislation. The above is minimum shelf
life, thereafter the paint quality is subject to re-inspection.

Date of issue: 8 November 2016 Page: 4/5

This Technical Data Sheet supersedes those previously issued.


The Technical Data Sheet (TDS) is recommended to be read in conjunction with the Safety Data Sheet (SDS) and the
Application Guide (AG) for this product. For your nearest local Jotun office, please visit our website at www.jotun.com
Technical Data Sheet
Penguard Express

Caution
This product is for professional use only. The applicators and operators shall be trained, experienced and have
the capability and equipment to mix/stir and apply the coatings correctly and according to Jotun's technical
documentation. Applicators and operators shall use appropriate personal protection equipment when using this
product. This guideline is given based on the current knowledge of the product. Any suggested deviation to suit
the site conditions shall be forwarded to the responsible Jotun representative for approval before commencing
the work.

Health and safety


Please observe the precautionary notices displayed on the container. Use under well ventilated conditions. Do
not inhale spray mist. Avoid skin contact. Spillage on the skin should immediately be removed with suitable
cleanser, soap and water. Eyes should be well flushed with water and medical attention sought immediately.

Colour variation
When applicable, products primarily meant for use as primers or antifoulings may have slight colour variations
from batch to batch. Such products may fade and chalk when exposed to sunlight and weathering.

Disclaimer
The information in this document is given to the best of Jotun's knowledge, based on laboratory testing and
practical experience. Jotun's products are considered as semi-finished goods and as such, products are often
used under conditions beyond Jotun's control. Jotun cannot guarantee anything but the quality of the product
itself. Minor product variations may be implemented in order to comply with local requirements. Jotun reserves
the right to change the given data without further notice.

Users should always consult Jotun for specific guidance on the general suitability of this product for their needs
and specific application practices.

If there is any inconsistency between different language issues of this document, the English (United Kingdom)
version will prevail.

Date of issue: 8 November 2016 Page: 5/5

This Technical Data Sheet supersedes those previously issued.


The Technical Data Sheet (TDS) is recommended to be read in conjunction with the Safety Data Sheet (SDS) and the
Application Guide (AG) for this product. For your nearest local Jotun office, please visit our website at www.jotun.com

You might also like