Professional Documents
Culture Documents
Type EA·E·C≤60
Treatment
D, P, Q Tolerance h7 D, P, Q Tolerance g6 MMaterial SSurface EIf 3 keyways are required, use both KC and WKC.
1 KC KC, A=1mm Increment b b t
SFRHQ SFRQ Black Oxide KC50-A10
S45C Equiv. location KC A Shaft Dia. Reference Tolerance Reference r
1.6
PSFRHQ PSFRQ Electroless Nickel Plating Dimension (N9) Dimension Tolerance
1.6
t
6.3
2D
7Q
EPKC·QKC≤50
1.6
1.6
Keyway PKC(QKC)≤F(T)
PKC PKC, QKC XNot applicable to P5 or less.
4F 3L 6T on Shaft PKC QKC
QKC =1mm Increment
PKC10·QKC15
End EThe example above shows the keyway shape for the specs KC, WKC, K=0,
(Y) D·P·Q h7 Tolerance g6 Tolerance KC+A≥L and WKC+C+K+E>L.
3 0 -0.002
-0.010 -0.008
0 -0.004 EG·J·V≤50
3.1~6 -0.012 -0.012 EKeyway(s) and set screw flats are added in the same plane. When the
1 FC FC, G=1mm Increment FC10-G3
0 -0.005 location distance of the alterations are over 500mm, ±2 degree phase differential
6.1~10 -0.015 -0.014 FC G may occur.
10.1~18 0 -0.006 D H
-0.018 -0.017 Set Screw Flat
6~17
6~17 11
18.1~30 0 -0.007
-0.021 -0.020 20~30 22
EFor Circularity, Perpendicularity, L Dimension Tolerance, refer to the next page, P.570. 2 WFC J V W WFC
WFC, J, W, V
WFC10-J3-W10-V3
20~30
locations =1mm Increment
H
Q D, P and Q Tolerance h7
Part Number Changes L dimension tolerance.
0.1mm Increment 1mm Increment (Y)
1Type 2D L Dimension Tolerance LKC - LKC EL<500C L±0.05
max. LKC
D, P, Q Tolerance h7 h7 Tolerance 3L 4F·6T 5P·7Q L≥500C L±0.1
6 0 20.0~296.0 3 4 5 300
-0.012
Adds a slit cam groove. D d L1
8 0 20.0~396.0
3≤P · Q<D UC
6 5
4
10 -0.015 20.0~400.0 Slit Cam Groove UC l1 UC UC10 EUC+L1≤L 8 7
SFRHQ =1mm Increment 10 8
12 25.0~400.0 EUC≥1 12 10
5
0 2≤F≤Px5 d XNot applicable to D15 or more.
PSFRHQ 15
-0.018
25.0~400.0 2≤T≤Qx5 400
5≤P · Q<D
17 30.0~400.0
D W
SSFRHQ 20 30.0~400.0 ESC+L2≤L 6 5
L2
0 SC=0 or SC≥1 8 7 8
25 30.0~400.0 EMachined on a single plane. 10 8
-0.021 10≤P · Q<D SC 12 10
30 30.0~400.0 500 Wrench Flats SC l2 SC SC10 When the distance of the 15 13
=1mm Increment 10
alterations are over 500mm, ±2 20 17
EWhen D-P (Q)≤2, chamfer C at the step is 0.2 or less.EFor P and Q dimensions, 27 cannot be specified. degree phase differential may 25 22
30 27 15
W occur.
Q D, P and Q Tolerance g6
Part Number
0.1mm Increment 1mm Increment (Y)
1Type 2D
max.
D, P, Q Tolerance g6 g6 Tolerance 3L 4F·6T 5P·7Q Accuracy Standards
6 -0.004 20.0~296.0 3 4 5 300
-0.012
8 -0.005 20.0~396.0 Item Accuracy Diagram Accuracy
3≤P · Q<D
10 -0.014 20.0~400.0 D Circularity
SFRQ M
12 25.0~400.0 Over or Less
-0.006 2≤F≤Px5 Circularity 5 13 0.004
PSFRQ 15
-0.017
25.0~400.0 2≤T≤Qx5 400 13 20 0.005
5≤P · Q<D ɐ M Timing Pulley
17 30.0~400.0 20 30 0.006
SSFRQ 20 30.0~400.0
-0.007
25 30.0~400.0 Straightness 0.01/100
-0.020 10≤P · Q<D
30 30.0~400.0 500
- 0.01/100
EWhen D-P (Q)≤2, chamfer C at the step is 0.2 or less.EFor P and Q dimensions, 27 cannot be specified.
D
P
Order Standard Service Non-Standard Service
3 * Quantity Regular Quantity Large Quantity Large Quantity
Perpendicularity 0.05
D
P
Concentricity 0.06
Quantity
+5 50~100 Ø0.06
L and Other Length Tolerance Bearing with Housing
Over or Less Tolerance
2 6 ±0.1
Dimension
Tolerance 6 30 ±0.2
30 120 ±0.3
L 120 400 ±0.5
400 800 ±0.8
569 570