Professional Documents
Culture Documents
1. The FT series sensor uses a visible light semi-conductor laser for pointers.
WARNING 2. The FT series is classified as a Class 1 laser product.
3. Use of controls or adjustments, or performance of procedures
Ultra-Compact Digital Infrared other than those specified herein may result in hazardous radia-
tion exposure.
4. Do not disassemble this product. Laser emission from this product
Temperature Sensor 5.
is not automatically stopped when it is disassembled.
Do not stare into the direct or specularly reflected beam.
Wavelength
FT-H10/H20/H30
655 nm
FT-H50/H40K/H50K
Handling
sensor head
1. Do not drop the FT series products, bang them against something, or measurement
NOTICE
apply excessive force. Handle the product by holding it by the main body. through hole
2. Do not pull heavily on the cable.
3. Do not use a sharply pointed object to press the setting keys.
Refer to the table below for recommended hole diameters based on distance.
Wiring Detection distance 200 400 600 800 1000 1200 1400 1600
Hole diameter φ 30 60 90 120 150 180 210 240
CAUTION 1. Before wiring the FT series, check the color of the wires.
2. Use the FT series within the rating range. Do not use a load that
exceeds the allowable limit. Unit: mm
Cleaning
1. Use an insulated stabilizing supply for the power supply.
NOTICE
2. Do not apply excessive tensile force to the cable.
3. Ensure that the cable tip does not become submerged in water
Dirt on the sensor lens may result in errors. Clean the lens as shown in the
during wiring work. outline below. Make sure to turn off power to the sensor before cleaning the
4. Isolate the cable from power supply lines or power lines. lens.
5. Keep the cable as far as possible from any source of noise.
Other
1. Three seconds after supplying power to the FT series is its power
NOTICE
ON reset time. Do not use outputs from the sensor during this
period.
2. The display value may drift immediately after turning on the Get rid of dust on the lens by using a blower If the lens is badly soiled, gently wipe it with a
power. In this case, make sure to use the FT Series after warm- made for cleaning camera lenses. Do not at- cotton swab. If the dirt still cannot be removed,
ing up for 15 to 30 minutes. tempt to remove dust by breathing directly on the dip the swab in a small amount of alcohol and
lens. wipe the lens. Do not use an organic solvent oth-
er than alcohol under any circumstances.
• When used in an environment with high dust, use the FT-S1 tough box with
air purge function. For details about FT-S1, contact your nearest KEYENCE
office.
1 E FT-W-IM
■ FT-55AW/55AWP (Panel mount models)
Checking the Package Contents
Before using the FT Series, check that the following items are all included in
1 Create a panel opening for mounting referring to the dimensions below.
(unit: mm)
the package for each model.
X=24x(A-1)+21
■ Sensor Head When 'A' units are
FT-H10/H20/H30 FT-H50/H40K/H50K X mounted side-by-side
45
83.1
+0.4
21 +0.1
anchoring ring
Power cable *2
Front protection The sensor head cable and power cable are each equipped with connector
cover*3 x1 covers.
(2m) x1
Point After the connectors are inserted into the amplifier, attach the connector
covers over the connectors. Finally, lock the base of the connector covers
Instruction manual x1
with the anchoring rings.
Unit cover sticker (black sheet)*4 x1
Unit conversion sticker*5 x1
Fitting the Amplifier with a Mounting Bracket easily become disconnected. anchoring ring
Fix the amplifier as shown in the diagram using
the included mounting bracket.
E FT-W-IM 2
● If the cable has been cut to a shorter length, install the connector as follows:
FT-H40K
1 Cut the cable to an appropriate
approx. approx.
26
ø11
26
ø7.5
26
ø6
26
ø4
26
ø11.5
laser pointer gap (typ.)
detection area diameter (mm)
connector connector
It is not necessary to remove
cover body
Point the covering from the core
wires.
0 100 150 200 300 detection distance (mm)
connector
2 Insert the cables according to the lock
laser pointer
measurement
area
FT Series C
target
TIM
sensing area
diameter
pointer gap
set mode
button button
bank selection
preset value indicator timing
indicator indicator
FT-H20
24.5 13 8 17 laser pointer gap (typ.)
ø11 ø8.5 ø6 ø14.5 detection area diameter (mm)
Switching Displays
TIM
FT-H30 TIM
press
SELECT BANK
TIM
C Hold Display
FT Series C
press
press SELECT BANK
press
TIM
0 200 400 600 detection distance (mm)
C Hold Display
FT Series C
press
SELECT BANK
TIM
press
they will appear to rotate clockwise, as shown in the above diagrams. SELECT BANK
TIM
SELECT BANK
TIM
3 E FT-W-IM
Basic Settings Automatically Setting the Preset Value
● Setting Emissivity (Temperature Mode only) The preset value can automatically be set. This is set from Temperature (Infra-
See option 5 on p. 5 for more about selecting Temperature Mode. red Radiation)/ Preset Value display screen .
SELECT BANK
TIM
1 Press once without a target.
“SEt” will begin flashing in the preset
value display.
1 Press to start setting the emissivity.
C
FT Series
SELECT BANK
TIM press
SELECT BANK
TIM
3 The preset value will be displayed.
The preset value will be the median of
the values measured when was
Upper display (red) blinks Lower display (green) blinks
pressed for the first time and when
●When emissivity is unknown was pressed for the second time.
C
The emissivity is automatically calculated by entering the temperature of the FT Series
measuring target (the value measured by an instrument such as a contact SELECT BANK
thermometer). TIM
Make sure to set the emissivity under the same setting condition and tem-
perature as those under which the FT Series is actually used. However, the
Point display will read "FFFF" when the gap between the target and the ambient When there is not sufficient difference between the first and second mea-
temperature is small. In this case, set the temperature with a warmer target Point sured values, “ ” will flash in the display, but the preset value will
or directly enter the emissivity. still be updated.
Reference If the temperature cannot be measured with a contact thermome- ■ Fully-Automatic Calibration
ter or other instruments, a simplified method is available to
measure the temperature. See “Introducing Options” in the lower
right-hand section of this page for the detail.
1 Let the target pass by while pressing
and holding .
TIM
TIM seconds and the
display will flash.)
● Setting the Preset Value Manually 3 The preset value will be displayed. The preset value will be the median of
B Switch to the Temperature (Infrared Radiation)/Preset Value display screen. the maximum and minimum values measured while was held down.
FT Series C
C
Press to change the preset value. FT Series
SELECT BANK
TIM Select Preset Value 1 or Preset Value 2 with the SELECT BANK
TIM
or buttons.
● Switching between the Hold Displays Select preset value 1 or preset value 2 by pressing + or + .
Preset Value 1 is calibrated when Preset Value 1 is selected, and Preset
See option 9 on p. 5 for the Hold Display. Value 2 when Preset Value 2 is selected.
C Switch to the Hold Display screens.
Peak/Bottom Display Peak Display ■ Options
FT Series C press FT Series C
If the emissivity and temperature of the measurement target are unknown, use the
SELECT BANK SELECT BANK optional blackbody tape to take simplified measurements.
TIM TIM
press
Option Blackbody Tape
When Auto Hold is selected,
Model OP-91147
the lower display reads " ".
press press Emissivity 0.95
Alternates between displays
Upper Temperature Limit 180 °C (356 °F)
FT Series C
SELECT BANK
press
Bottom Display
FT Series C
1 Stick the blackbody tape to the measurement target, heat it to a suitable
TIM temperature (+20 °C (+68 °F) or more above room temperature), and
SELECT BANK maintain that temperature as best as possible.
TIM
red digital display: peak value press
green digital display: bottom value 2 Set the emissivity to 0.95 (emissivity of blackbody tape). See “Setting
Pressing + for 3 seconds or more resets the hold values. Emissivity” for how to set this value.
Laser ON/OFF does not affect detection. Use it as a rough indication of the
measurement view.
E FT-W-IM 4
Programming Menu Flowchart
FT Series C
When USEr
SELECT BANK
is selected Hysteresis width setting
TIM
0 to 1400 (H40K/H50K)
TIM
SELECT BANK
• Upper limit detection mode (32 to 2552°F)
TIM • Lower limit detection mode * The setting unit is the one selected at
option 2.
• Upper/lower limit detection mode press "Infrared Radiation Mode"
press Skipped during IR mode 0 to 9999
0 to 2500 (H50 only)
2 Switch display units
FT Series C When Press to select the option.
C
using the • Displays temperature in 1°C (1°F) units FT Series
9 Select hold value display p.7
SELECT BANK
H50/ • Displays temperature in 0.1°C (0.1°F) units
TIM H40K/ SELECT BANK
Press to select the option.
H50K TIM • Peak/bottom
press • Automatic peak/bottom hold
press
3 Switch response time
C
Press to select the option.
FT Series
FT Series C
4 Switch output mode
FT Series C
Press to select the option. SELECT BANK
TIM
Output 1 Output 2
SELECT BANK
TIM
• Ends the menu
• Continue to set each type of mode
When AnLG
is selected Skipped during IR mode ■ Initializing / Changing the temperature unit
Analog output lower limit setting C
FT Series C
Press to select the option. 1 While holding down , press five times until
FT Series
SELECT BANK Setting range “rSEt/no” appear in the displays. SELECT BANK
TIM TIM
-50 to 520 (H10/H20/H30/H50)
(-58 to 968°F)
-50 to 1400 (H40K/H50K)
press (-58 to 2552°F)
* The setting unit is the one selected at option 2.
2 Press or to select “YES”. FT Series C
SELECT BANK
TIM
FT Series C
Analog output upper limit setting 3 Pressing displays “unit/C” or “unit/F”. Press FT Series C
TIM
FT Series C
7 Switch input 2 (purple line) p.6
Press to select the option.
5
SELECT BANK
C
• Not used FT Series
TIM
Press or and select “YES”.
• Bank input
SELECT BANK
• Timing input
press TIM
TIM • Standard
• Hysteresis is 80% of the standard width.
press • Hysteresis width can be set freely.
5 E FT-W-IM
■ Selecting the Bank
Settings for Each Mode
Selecting with Operation Keys
If key lock is on, cancel the key lock (p. 7) and follow the steps below.
Operation Mode
1 Switch to Temperature/Emissivity display, as shown in “Switching
■ Upper Limit Detection Mode Displays” (p. 3).
(F-1) P1
Hys 2 While holding down , press or .
This mode detects when the tempera-
P2 Hys C
ture rises above a fixed value. FT Series
limit. TIM
Output 2 OFF ON OFF Switch between the banks in the following manner depending on the input/out-
put 1/2 settings.
Output 1 Turns ON when the temperature (or amount of infrared radiation) rises
above preset value 1 (P1). • Bank input (bn-1) is selected only for input /output 1 (option 6 on p. 5)
Turns OFF again when the value falls below the range of hysteresis Bank 0 Bank 1
from preset value 1.
Output 2 Turns ON when the temperature (or amount of infrared radiation) rises • Bank input (bn-2) is selected only for input /output 2 (option 7 on p. 5)
above preset value 2 (P2).
Turns OFF again when the value falls below the range of hysteresis Bank 0 Bank 2
from preset value 2.
• Bank input is selected for both input /output 1/2 (bn-1, bn-2) (option 6,
7 on p. 5)
■ Lower Limit Detection Mode Bank 0 Bank 1 Bank 2 Bank 3
Hys
(F-2) P2
Output 2 ON ON It will take 20 ms to reflect the bank selection. Until the selection is reflected,
OFF
the sensor retains the same condition as before the bank change.
Output 1 Turns ON when the temperature (or amount of infrared radiation) rises After selecting the bank, the display and output assessment will contain the
above preset value 1 (P1).
Turns OFF again when the value falls below the range of hysteresis following time lag.
from preset value 1. - Display (digital numbers) : about 0.1 sec
Output 2 Turns ON when the temperature (or amount of infrared radiation) falls - Output Assessment : 20 ms plus response time
below preset value 2 (P2).
Turns OFF again when the value rises above the range of hysteresis [Ex.] When output is OFF before bank change and ON after bank change
from preset value 2.
bank input
Detection Mode
OFF ON
■ Temperature Mode control output
20ms + response time
This mode uses the set emissivity to convert the amount of received infrared
radiation into temperature, and displays this number in degrees. See “Setting
Emissivity” on p. 4 for more about setting the emissivity. Analog Output (AnLG)
Bank Function (Temperature Mode Only) For 0 °C (32 °F) (A-Lo) and For 200 °C (392 °F) (A-Lo) and
When measuring in Temperature Mode (option 5 on 500 °C (932 °F) (A-Hi) 400 °C (752 °F) (A-Hi)
C
p. 5), BANK1 and BANK2 can be combined to hold up FT Series
Analog output Analog output
to eight preset values and up to four emissivities, as SELECT BANK
(mA) (mA)
Bank Indicator
Bank No. 4 4
BANK1 BANK2
0 500 (°C) 0 200 400 500 (°C)
0 Off Off 32 932 (°F) 32 392 752 932 (°F)
E FT-W-IM 6
Timing Input Upper Limit Range Error • Return the sensor
FT Series C Reading exceeds the within the rated
This option can be used when you want to assess the control output or display
upper limit of the detection temperature range.
the temperature for only a limited period of time. SELECT BANK
range. • Set the emissivity to
To use timing input, set “Switch input (purple line)” (option 7 on p. 5) to timing
TIM
an appropriate value.
input (t-in). Lower Limit Range Error • Return the sensor
• The temperature (infrared radiation) display and output is assessed only FT Series C Reading exceeds the within the rated
when the sensor receives the timing signal. lower limit of the detection temperature range.
When the timing signal is off, the amplifier will scroll a single LED segment SELECT BANK
TIM
range. • Set the emissivity to
across the display. (When analog output is being used, the analog output an appropriate value.
operates normally no matter what timing input is used.)
• After receiving the input signal, the display and output assessment will con-
tain the following time lag.
– Display (digital numbers) : about 0.1 sec Input/Output Circuit Schematic
– Output Assessment : 2 ms plus response time ■ FT-50AW/55AW
Main circuit
The peak/bottom hold values will be displayed after turning the power ON or Load 5 to 40 VDC
White
after the hold values are reset (see p. 4 ). (Control output 2)
Load 5 to 40 VDC
Blue
■ Auto Peak/Bottom Hold (Auto) 0V
Analog output/Bank input1/
Pink selectable
The peak value updates when the temperature rises above the P1 preset Input/output circuit1
Timing input/Bank input2/
value. Likewise, the bottom value updates when the temperature drops below Purple selectable
Input circuit 2
the P1 preset value.
[Ex.] Peak Hold Value Update [Ex.] Bottom Hold Value Update External input circuit
peak hold Analog output circuit (Bank input 1 & 2, Timing input)
temperature display value temperature
Pink Analog
output 5V
Main circuit
(4 to 20 mA)
Main circuit
Pink/
preset value preset value Blue Purple
0V
Blue
bottom hold
display value (shorting current 1 mA max.)
Peak Hold updates when the temperature Bottom Hold updates when the temperature
climbs above the reset value and holds until falls below the reset value and holds until ■ FT-50AWP/55AWP
the next time the temperature peaks. the next time the temperature falls.
Input/output circuit schematic
Brown
Power Save Mode (Eco) Black
12 to 24 VDC
Overcurrent protection circuit
(Control output 1)
When Power Save Mode is turned ON (option 10 on p. 5), the power save dis-
Main circuit
White
(Control output 2)
play will turn on after three minutes of inactivity. Load
• When the power save display is on, only one segment C FT Series
Load
Blue
will blink in the preset value display. 0V
The output indicator, bank indicator, and timing indica- SELECT BANK
Pink Bank input 1/analog output:
TIM
Input/output circuit1
Selectable
tor operate as normal.
Purple Bank input 2/timing input:
• When the power save display is on, pressing any button will return to nor- Input circuit 2
Selectable
mal display.
External input circuit
Key Lock Function (Loc) Analog output circuit (Bank input 1 & 2, Timing input)
Analog 12 to 24 VDC
Pink Brown
This function prevents the operation keys from changing the settings. They can output
Main circuit
(4 to 20 mA)
Main circuit
To release key lock, press and hold + (or + ) for about three
seconds in key lock mode. Emissivity
• When “unL” flashes in the preset value display, key FT Series C
The following chart shows examples of emissivity.
lock has been released.
SELECT BANK
TIM
Substance Emissivity Substance Emissivity
Asphalt 0.90 to 0.98 Leather 0.75 to 0.80
Concrete 0.94 Charcoal (powder) 0.96
Error Display Cement 0.96 Lacquer 0.80 to 0.95
Sand 0.90 Lacquer Matte Black 0.97
Error Display Cause Response
Soil 0.92 to 0.96 Rubber (black) 0.94
Error Head Water 0.92 to 0.96 Plastic 0.85 to 0.95
• The sensor head is not
FT Series C Repair the broken Ice 0.96 to 0.98 Wood 0.90
connected.
connection to the sensor Snow 0.83 Paper 0.70 to 0.94
SELECT BANK
• The connection to the
head.
TIM
sensor head is broken. Glass 0.90 to 0.95 Aluminum Oxide 0.20 to 0.30
Ceramic 0.90 to 0.94 Chromium Oxide 0.81
Amplifier EEPROM Error Marble 0.94 Copper Oxide 0.78
FT Series C • Reset the power. Fluorite 0.30 to 0.40 Iron Oxide 0.78 to 0.82
An error occurs while
• Initialize the sensor, Gypsum 0.80 to 0.90 Nickel Oxide 0.90
SELECT BANK
reading internal data.
TIM
referring to p. 5. Plaster 0.89 to 0.91 Zinc Oxide 0.11 to 0.28
Red Brick 0.93 to 0.95 Pure Copper Oxide 0.56 to 0.64
Overcurrent Error Irregular Bronze
Fiber 0.90 0.55
FT Series C Check the load and Surface
Overcurrent is flowing into
return it within the rated Cloth (black) 0.98 Stainless Steel 0.45
SELECT BANK
the control output.
TIM
range. Skin (human) 0.98 Rusted Steel 0.69
7 E FT-W-IM
Specifications
■ Sensor Head
Low / Medium Temperature High Temperature
Type
Small Spot Mid Range Long Range Ultralong Range Mid Range Ultralong Range
Model FT-H10 FT-H20 FT-H30 FT-H50 FT-H40K FT-H50K
Rated temperature range *1 0 to 500 °C (32 to 932 °F) 0 to 1350 °C (32 to 2462 °F)
Display temperature range -50 to 520 °C (-58 to 968 °F) -50 to 1400 °C (-58 to 2552 °F)
Detection distance No limits*2
17.5 / φ 6.3 mm 60 / φ 8.5 mm 200 / φ 15 mm 500 / φ 18 mm 100 / φ 7.5 mm 500 / φ 18 mm
Detection distance (mm) / detection area diameter 35 / φ 1.5 mm 120 / φ 6 mm 400 / φ 18 mm 1500 / φ 30 mm 200 / φ 4 mm 1500 / φ 30 mm
52.5 / φ 8 mm 180 / φ 14.5 mm 600 / φ 33 mm 3000 / φ 75 mm 300 / φ 11.5 mm 3000 / φ 75 mm
Sight*3 Dual visible red Laser
Detection components Thermopile
Detection wavelength 8 to 14 μm
Repeatability ±0.5 °C (±0.9 °F) ±3 °C (±5.4 °F)
Emissivity (ε) correction 0.10 to 1.99 (0.01 steps)
Operating ambient -10 to +55°C (14 to 131°F) (no freezing)
temperature
Environmental Operating ambient 35 to 85% RH (no condensation)
resistance humidity
Vibration resistance 10 to 55 Hz, 1.5 mm double amplitude, 2 hours in each XYZ axis
Shock resistance 500 m/s2, 10 times in each axis XYZ, total 60 times
Case: glass-reinforced polyetherimide
Infrared radiation collector lens: germanium
Material Laser emission areas: polyarylate
Lens tube*4: aluminum, Cable: vinyl chloride
Mounting bracket: SUS304
Weight Approx. 120 g Approx. 150 g
■ Amplifier
Type DIN rail mounted type Panel mounted type
NPN output FT-50AW FT-55AW
Model
PNP output FT-50AWP FT-55AWP
Power voltage*1 12 to 24 VDC*3, Ripple (P-P): 10% max, Class2 or LPS
Normal mode 1400 mW (12 V), 1600 mW (24 V)
Current consumption
Power Save Mode 1150 mW (12 V), 1350 mW (24 V)
Display method 4 + half digit 7-segment LED
Red and green dual display (Uppercase letter height: Upper display: 8 mm (red), Lower display: 5.7 mm (green))
Operation indicators Red LED x 3 (corresponding to Control Output 1, Control Output 2, and Timing Input)
Display resolution (when using H10/H20/H30) 0.1 or 1 °C (0.2 °F or 1.8 °F), (when using H50 / H40K / H50K) 1 °C (1.8 °F)
Hysteresis (hys) Variable
Response speed Select HSP, 30 ms, 100 ms, 200 ms, 500 ms, 1000 ms, 5000 ms (HSP: representative example is 10 ms, 15 ms max.)
Switch bank Bank input is made by switching the timing input line and analog output line / Up to 4 banks can be programmed
Bank settings Emissivity (temperature mode only) and preset value x 2 can be set for each bank
Timing input Input time: 2 ms or more
External input
Bank input Input time: 20 ms or more
Control output NPN (PNP) open collector x 2 ch
(N.O./N.C. selectable), 40 VDC (30 VDC) or less, Max 100 mA (50 mA), Residual voltage: 1 V or less
Analog output 4 to 20 mA, maximum load resistance 260 Ω
(Upper/lower limit range for analog output can be set optionally)
Operating ambient
-10 to +50 °C (14 to 122 °F) (no freezing)
temperature*2
Environmental
resistance Operating ambient 35 to 85% RH (no condensation)
humidity
Vibration resistance 10 Hz to 55 Hz, 1.5 mm double amplitude, 2 hours in each XYZ axis
Main unit and cover: polycarbonate
Main unit Keycaps: polyester elastomer
Material Cable: vinyl chloride
Mounting bracket Mounting bracket: SPCC Mounting bracket: polyacetal
Front protection cover: polycarbonate
Weight Approx. 85 g
* 1: Use with the over current protection device which is rated 24V or more and not more than 1A.
* 2: When using analog output: -10 to +45°C (14 to 113°F).
* 3: When using this product as an UL recognized product, use the power supply with Class 2 output defined in NFPA70 (NEC: National Electrical Code).
E FT-W-IM 8