Professional Documents
Culture Documents
Main benefits
Productivity The small bolting unit on the Boltec S has been optimised to
reduce the overall feed length by 100 mm when compared to earlier bolting
unit designs. This gives potential for reduced drive sizes whilst retaining the
same bolt lengths used previously. The bolt magazine can be loaded in the
vertical position without power to the machine, providing a fast and safe
loading procedure.
Rock Drill The COP RR11 rock drill is optimised for bolt hole drilling, with
it’s light weight and high frequency it reduces loads on the boom whilst
achieving superior penetration rate. For larger hole diameters required for
some friction bolt types or harder rock conditions the optional COP RR14
delivers the hitting power needed to get the job done.
2
Short dead length
3
Boltec S mechanized bolting
Safety and quality of bolt installation is our focus. The Boltec S is designed with
standard and optional features that ensure these goals are met.
+ Safety
Mechanised bolting removes the operator from the potential danger area
of unsupported ground. All drilling and bolt installation is controlled from
the operator station under a FOPS canopy or optional ROPS and FOPS air
conditioned cabin.
+ Operator comfort
The operator position affords excellent visibility of the bolting operation
as well as when tramming the vehicle. The operator area is spacious and
features a swingable operator seat for driving and bolting. The optional
ROPS and FOPS air conditioned cabin enhances the operator’s comfort
especially in extreme temperatures or dusty conditions.
4
Technical specifications
= Standard = Option
BUT 32 Deutz 4-cylinder BF4L 914, 4-stroke turbo diesel engine, Tier 2
(72 kW, 96 hp at 2 500 rpm, 355 Nm at 1 600 rpm)
Automatic boom lubrication - rear part of the boom
Deutz TD3.6 L4 55kW Stage IIIB / Tier 4i
Electric heater for hydraulic oil tank, electric motors and diesel engine
Bolting unit Articulated ±40° steering angle
Magazine capacity 10 bolts Four wheel drive
Size of face plates, rectangular, diameter, max 150 x 150 mm Electrical system 24 V
Size of face plates, round, diameter, max Ø 200 mm Batteries 2 x 12 V, 70 Ah
Bolt length, max 1.5-2.4 m Automatic differential lock on front axle, limited slip
Swellex, Mn 12, Mn 16, Mn 24 Tires 9.00 x R20
Split-Set, SS39, SS46 Clearance outside axles rear 15°
Mechanical anchored bolts (expanding shell) Front and rear hydraulic jacks
Split Wedge Fuel tank volume 60 L
Rebar bolts – manual resin/cement cartridges Central lubrication system
Extension system for injection hose for resin cartridges Tramming lights 6 x 40 W LED + 2 x 70 W halogen
Dual bolt lengths - shorter bolt 70 % the length of longer bolt Working lights, mounted on roof 3 x 35 W, 24 V HID
Dual bolt types Boot washing kit
Extension drilling kit Illuminated stairs for platform
Central grease point
Low oil level indicator Fire suppression system ANSUL - automatic release (checkfire)
Oil temperature meter
Filtration 16 μm
Cabin (option)
Oil filter indicator
ROPS and FOPS approved airconditioned cabin, noise level <80 dB(A)
Mineral hydraulic oil
Mediaplayer
Electric oil filling pump
12 V outlet
Biodegradable hydraulic oil
Electrical heater, 1.2 kW, 230 V (CE)
Hydraulic oil leakage shut down system
Swingable seat for drilling and tramming
Hydraulic oil thermostat
Manual spotlight, left and/or right
Ni-Cr plated piston rods (limitations exist)
Low-designed cabin, for seated operator cabin height 2 655 mm
Front window, 16 mm
Control system Front window, 24 mm
Rig Control System (RCS) FOPS-approved grizzly bar for front window
2 100
2 m from rigcentre, SBU for 2.4 m bolt 4 m height, SBU for 2.4 m bolt 2 m from rigcentre, SBU for 2.4 m bolt
Weight Dimensions
Total 13 700 kg Width 2 115 mm
Boom side 9 000 kg Height, roof down 2 100 mm
Engine side 4 700 kg Height, roof up 2 841 mm
Cabin height (option) 2 841 mm
Lowered cabin height (option) 2 691 mm
Recommended cable sizes and lengths
Length, tramming 10 020 mm
Voltage Dimension, mm2 Diameter, mm Length
Ground clearence 365 mm
380-400 V 3x70+3G16+2x1.5 37 110
Turning radius outer/inner 5 200 / 2 780
440 V 3x70+3G16+2x1.5 37 110
500-525 V 3x70+3G16+2x1.5 37 110
550-575 V 3x50+3G6+2x1.5 32 150 Tramming speed
660-690 V 3x35+3G6+2x1.5 28 200 On flat ground (rolling resistance 0.05) >15
1 000 V 3x35+3G6+2x1.5 28 200 On incline 1:8 >5
Recommendations are given for surrounding temperature of 40°C and altitude of 2 000 m.
7
Committed to sustainable productivity
We stand by our responsibilities towards our customers,
towards the environment and the people around us.
www.atlascopco.com
9851 3610 01a 2017-10 Örebro, Sweden. Legal Notice © Copyright 2017, Atlas Copco Rock Drills AB, Örebro, Sweden. All product names in this publication are trademarks of Atlas Copco. Any unauthorized use or
copying of the contents or any part thereof is prohibited. Illustrations and photos may show equipment with optional extras. No warranty is made regarding specifications or otherwise. Specifications and equipment are
subject to change without notice. Consult your Atlas Copco Customer Center for specific information.