Professional Documents
Culture Documents
org
Extrusion, Second Edition (#06998G)
EXTRUSION
SECOND EDITION
Editors
M. Bauser
G. Sauer
K. Siegert
ASM International姞
Materials Park, Ohio 44073-0002
www.asminternational.org
© 2006 ASM International. All Rights Reserved. www.asminternational.org
Extrusion, Second Edition (#06998G)
Copyright 䉷 2006
by
ASM International威
All rights reserved
Originally published as Strangpressen
䉷 2001 Aluminium-Verlag, Düsseldorf, Germany
No part of this book may be reproduced, stored in a retrieval system, or transmitted, in any form or by any
means, electronic, mechanical, photocopying, recording, or otherwise, without the written permission of the
copyright owner.
First printing, December 2006
Great care is taken in the compilation and production of this Volume, but it should be made clear that NO
WARRANTIES, EXPRESS OR IMPLIED, INCLUDING, WITHOUT LIMITATION, WARRANTIES OF
MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE, ARE GIVEN IN CONNECTION
WITH THIS PUBLICATION. Although this information is believed to be accurate by ASM, ASM cannot
guarantee that favorable results will be obtained from the use of this publication alone. This publication is
intended for use by persons having technical skill, at their sole discretion and risk. Since the conditions of
product or material use are outside of ASM’s control, ASM assumes no liability or obligation in connection
with any use of this information. No claim of any kind, whether as to products or information in this publication,
and whether or not based on negligence, shall be greater in amount than the purchase price of this product or
publication in respect of which damages are claimed. THE REMEDY HEREBY PROVIDED SHALL BE THE
EXCLUSIVE AND SOLE REMEDY OF BUYER, AND IN NO EVENT SHALL EITHER PARTY BE LIA-
BLE FOR SPECIAL, INDIRECT OR CONSEQUENTIAL DAMAGES WHETHER OR NOT CAUSED BY
OR RESULTING FROM THE NEGLIGENCE OF SUCH PARTY. As with any material, evaluation of the
material under end-use conditions prior to specification is essential. Therefore, specific testing under actual
conditions is recommended.
Nothing contained in this book shall be construed as a grant of any right of manufacture, sale, use, or repro-
duction, in connection with any method, process, apparatus, product, composition, or system, whether or not
covered by letters patent, copyright, or trademark, and nothing contained in this book shall be construed as a
defense against any alleged infringement of letters patent, copyright, or trademark, or as a defense against
liability for such infringement.
Comments, criticisms, and suggestions are invited, and should be forwarded to ASM International.
Prepared under the direction of the ASM International Technical Books Committee (2006–2007), James Foley,
Chair.
ASM International staff who worked on this project include Scott D. Henry, Senior Product Manager; Charles
Moosbrugger; Editor, Diane Grubbs, Editorial Assistant; Bonnie Sanders, Production Manager; Madrid Tram-
ble, Senior Production Coordinator; Diane Wilkoff, Production Coordinator; Pattie Pace, Production Coor-
dinator; Kathryn Muldoon, Production Assistant
Library of Congress Cataloging-in-Publication Data
Extrusion / editors, M. Bauser, G. Sauer, K. Siegert. — 2nd ed.
p. cm.
Includes bibliographical references and index.
ISBN-13: 978-0-87170-837-3
ISBN-10: 0-87170-837-X
1. Metals—Extrusion. 2. Aluminum alloys. I Bauser, M. (Martin) II. Sauer, G. (Günther) III. Siegert, Klaus.
TS255.E78 2006
671.3⬘4—dc22 2006050365
SAN: 204-7586
ASM International威
Materials Park, OH 44073-0002
www.asminternational.org
Printed in the United States of America
© 2006 ASM International. All Rights Reserved. www.asminternational.org
Extrusion, Second Edition (#06998G)
Contents
Foreword ................................................................................................................... xv
Authors .................................................................................................................... xvi
iii
© 2006 ASM International. All Rights Reserved. www.asminternational.org
Extrusion, Second Edition (#06998G)
iv
© 2006 ASM International. All Rights Reserved. www.asminternational.org
Extrusion, Second Edition (#06998G)
v
© 2006 ASM International. All Rights Reserved. www.asminternational.org
Extrusion, Second Edition (#06998G)
vi
© 2006 ASM International. All Rights Reserved. www.asminternational.org
Extrusion, Second Edition (#06998G)
vii
© 2006 ASM International. All Rights Reserved. www.asminternational.org
Extrusion, Second Edition (#06998G)
5.16.6.1 The Different Alloys, Their Structures, Properties, and Applications ........257
5.16.6.2 Casting of Copper-Tin Alloys ...........................................................258
5.16.6.3 Extrusion of Copper-Tin Alloys ........................................................258
5.16.6.4 Flow Type and Shell Defects ............................................................258
5.16.6.5 Competition from Wire Casting .........................................................258
5.16.7 Extrusion of Copper-Aluminum Alloys (Aluminum Bronzes) .......................258
5.16.7.1 The Different Alloys, Their Properties, and Applications .......................258
5.16.7.2 Binary Copper-Aluminum Alloys ......................................................259
5.16.7.3 Copper-Aluminum Alloys with Additions
(Complex Aluminum-Bronzes) .........................................................260
5.16.8 Extrusion of Copper-Nickel Alloys ..........................................................260
5.16.8.1 Materials, Structure, Properties, and Applications .................................260
5.16.8.2 Extrusion of Copper-Nickel Alloys ....................................................261
5.16.9 Extrusion of Copper-Nickel-Zinc Alloys (Nickel-Silver) ..............................261
5.16.9.1 Material, Structure, Properties, and Applications ..................................261
5.16.9.2 Extrusion of Nickel-Silver Alloys ......................................................262
5.16.9.3 Competition from Wire Casting .........................................................263
Extrusion of Semifinished Products in Titanium Alloys ......................................................263
5.17 Materials, Their Properties, and Applications ....................................................263
5.17.1 The Structure and Its Influence on the Properties ........................................263
5.17.2 The Most Important Titanium Alloys and Applications ................................264
5.17.3 Titanium Alloys Produced by Powder Metallurgy .......................................266
5.18 Billet Production, Extrusion ..........................................................................266
5.18.1 Casting, Billet Preparation, Billet Heating .................................................266
5.18.2 Extrusion, Lubrication ...........................................................................266
5.18.3 Flow Stress, Extrusion Defects ................................................................267
5.19 Tooling, Further Processing ...........................................................................268
Extrusion of Semifinished Products in Zirconium Alloys ....................................................268
5.20 Materials, Properties, and Applications ............................................................268
5.21 Billet Production, Extrusion ..........................................................................268
5.21.1 Casting, Billet Preparation ......................................................................268
5.21.2 Extrusion, Influence of the Structure .........................................................268
5.22 Tooling, Further Processing ...........................................................................269
Extrusion of Iron-Alloy Semifinished Products .................................................................269
5.23 General ......................................................................................................269
5.23.1 Process Basics ......................................................................................269
5.23.2 Importance of Steel Extrusion Today ........................................................270
5.24 Mild-Steel Tubes .........................................................................................270
5.24.1 Use of Mechanical Presses ......................................................................270
5.24.2 Application of Mechanical Presses ...........................................................270
5.24.3 Dimensional Range and Throughput .........................................................271
5.25 Seamless Alloy Steel Tubes ...........................................................................271
5.25.1 Extrusion in Competition with Other Hot-Working Processes ........................271
5.25.2 Alloys and Extrusion Properties ...............................................................271
5.25.2.1 Alloy Groups, Structure, Properties, and Applications ...........................271
5.25.2.2 Extrusion Properties, Defects ............................................................273
5.25.3 Billet Production ...................................................................................274
5.25.3.1 Melting, Casting, Hot Working .........................................................274
5.25.3.2 Homogenizing, Billet Preparation ......................................................275
5.25.4 Billet Heating, Lubrication ......................................................................275
5.25.4.1 Billet Heating ................................................................................275
5.25.4.2 Lubrication ....................................................................................276
5.25.5 Extrusion Process ..................................................................................277
5.25.6 Tooling ...............................................................................................278
5.25.7 Further Processing, Testing .....................................................................278
viii
© 2006 ASM International. All Rights Reserved. www.asminternational.org
Extrusion, Second Edition (#06998G)
ix
© 2006 ASM International. All Rights Reserved. www.asminternational.org
Extrusion, Second Edition (#06998G)
Chapter 6 Machinery and Equipment for Direct and Indirect Hot Extrusion ................323
6.1 Machinery and Equipment for Direct and Indirect Hot Extrusion ...........................323
6.1.1 Machinery for Direct Extrusion .................................................................323
6.1.1.1 Extrusion Press Design Principles .......................................................324
6.1.1.2 Main Subassemblies of the Direct-Extrusion Press .................................327
6.1.1.3 Auxiliary Equipment for Direct Extrusion ............................................335
6.1.1.4 Hydraulic Drive and Control Systems for Direct Extrusion ......................338
6.1.1.5 Electrical Drive, Control, and Regulation for Direct Extrusion .................341
6.1.1.6 Typical Operating Sequence for Direct Extrusion ...................................344
6.1.2 Machines for Indirect Extrusion ................................................................344
6.1.2.1 Press Design ...................................................................................345
6.1.2.2 Main Structural Components of Indirect-Extrusion Presses ......................347
6.1.2.3 Auxiliary Equipment for Indirect Extrusion ..........................................347
6.1.2.4 Hydraulic Drive Systems and Control for Indirect Extrusion ....................352
6.1.2.5 Electric Drive and Control for Indirect Extrusion ...................................352
6.1.2.6 Typical Operating Sequence in Indirect Extrusion ..................................353
6.2 Presses and Plant for Tube Extrusion ................................................................353
6.2.1 Direct Tube Extrusion .............................................................................355
6.2.1.1 Machine Construction Details of Tube Extrusion Presses .........................355
6.2.1.2 Main Subassemblies and Modules of Direct Tube Extrusion Presses ..........357
6.2.1.3 Auxiliary Equipment for Direct Extrusion ............................................361
6.2.1.4 Hydraulic Control Systems ................................................................361
6.2.1.5 Electrical Drive, Controls, and Additional Equipment for Direct
Tube Extrusion ................................................................................361
6.2.1.6 Typical Operating Sequence for Direct Tube Extrusion ...........................362
6.2.2 Indirect Tube Extrusion ...........................................................................362
6.2.2.1 Machine Design Details ....................................................................362
6.2.2.2 Main Subassemblies of Indirect Tube Extrusion Presses ..........................364
6.2.2.3 Typical Operating Sequence for Indirect Tube Extrusion .........................365
Billet Heating Systems .................................................................................................365
6.3 Induction Furnaces ........................................................................................365
6.3.1 General .................................................................................................365
6.3.1.1 Single-Billet Furnace ........................................................................366
6.3.1.2 Multibillet Furnaces ..........................................................................367
6.3.1.3 Induction Furnace with a Heated Holding Chamber ................................369
6.3.1.4 Boost Heating ..................................................................................370
6.3.1.5 Induction Furnaces with Hot Log Shear ...............................................372
6.3.2 Gas-Fired Billet Preheat Furnace ...............................................................372
6.3.2.1 General ..........................................................................................372
6.3.2.2 Rapid-Heating Gas-Fired Preheat Furnace with Billet Preheating ..............373
6.3.2.3 Combination Induction Furnace and Rapid-Heating Gas-Fired Furnace ......373
6.3.2.4 Rapid-Heating Gas-Fired Furnace with Boost Heater ..............................374
6.3.2.5 Rapid-Heating Gas-Fired Furnace with Hot Log Shear ............................375
6.3.3 Temperature Measurement and Control .......................................................375
x
© 2006 ASM International. All Rights Reserved. www.asminternational.org
Extrusion, Second Edition (#06998G)
xi
© 2006 ASM International. All Rights Reserved. www.asminternational.org
Extrusion, Second Edition (#06998G)
xii
© 2006 ASM International. All Rights Reserved. www.asminternational.org
Extrusion, Second Edition (#06998G)
xiii
© 2006 ASM International. All Rights Reserved. www.asminternational.org
Extrusion, Second Edition (#06998G)
Index ........................................................................................................................579
xiv
© 2006 ASM International. All Rights Reserved. www.asminternational.org
Extrusion, Second Edition (#06998G)
Foreword
The book Extrusion: Processes, Equipment, Tooling, edited by Kurt Laue and Helmut Stanger,
was published in 1976 by the Aluminium-Verlag GmbH, Düsseldorf. The excellent, wide, and often
deep overview enabled experienced engineers as well as students and academics to understand ex-
trusion processes, equipment, and tooling. For a long time, this book, which was also translated into
English, was the standard reference on extrusion.
Because it has been out of print for several years, it made sense to republish the book Extrusion
in a fully updated version. The editors have attempted to retain the character of the book as an
overview of the processes, equipment, and tooling. Extruded products have been discussed in more
detail to demonstrate the range of applications of extrusion and to stimulate the industrial application
of extrusion beyond that used today.
In addition, the metallurgical fundamentals of the extrusion process are covered in detail, because
the editors believe that extrusion can only be optimized by taking the materials technology into
account.
The discussions on extrusion equipment, plant, and tooling attempt to extend the overview with
application examples. Actual applications, however, require the cooperation of the customer, extruder,
tool maker and equipment manufacturer.
The book Extrusion is intended for both students and research engineers as well as engineers in
extrusion plants, manufacture of machinery and plant, tool manufacture, as well as the designers,
process developers, and managers of automotive companies, building industries, and plant manufac-
ture. The book should give an introduction to and an overview of extrusion. More detailed discussions
and the latest research results can be found in the technical literature.
The authors thank the co-authors of this book and the numerous companies that have helped in
its realization by providing the material for the figures and technical discussions. Specific mention
should be made of the support from Wieland-Werke AG, Ulm, and by the companies Alusuisse
Neuhausen and Alusingen. We should also thank the members of the “Extrusion Technical Com-
mittee” in the DGM for the valuable information they provided. These include, in particular, Dr. J.
Baumgarten, Dr. G. Fischer, and Dipl.-Ing. Rethmann. Thanks are also due to Y. Ismailoglu of IFU-
Stuttgart and A. Schug of Wieland-Werke Ulm for the preparation and production of numerous
photographs, drawings, tables, and diagrams.
The editors also give special thanks to the Aluminium Verlag for fulfilling the requests and re-
quirements of the editors and the authors and for the careful preparation of the contributions for
printing.
Sadly, one of the three editors, our dear colleague and friend, Professor Dr. Ing. Günther Sauer,
died on October 7, 2000. He gave a great deal of commitment and effort to the realization of this
book and completed all of his promised contributions to it before his sudden death. Unfortunately,
he was not allowed the pleasure of seeing this book in its final format. We would like to express our
sincere thanks for being a good colleague and a friend.
We hope this book fulfills the expectations of the reader and contributes to the further development
of extrusion.
Dr. rer. nat. Martin Bauser Prof. Dr.-Ing. Dr. H.C. Klaus Siegert
xv
© 2006 ASM International. All Rights Reserved. www.asminternational.org
Extrusion, Second Edition (#06998G)
Authors
xvi
ASM International is the society for materials
engineers and scientists, a worldwide network
dedicated to advancing industry, technology, and
applications of metals and materials.
Terms of Use. This publication is being made available in PDF format as a benefit to members and
customers of ASM International. You may download and print a copy of this publication for your
personal use only. Other use and distribution is prohibited without the express written permission of
ASM International.
No warranties, express or implied, including, without limitation, warranties of merchantability or
fitness for a particular purpose, are given in connection with this publication. Although this
information is believed to be accurate by ASM, ASM cannot guarantee that favorable results will be
obtained from the use of this publication alone. This publication is intended for use by persons having
technical skill, at their sole discretion and risk. Since the conditions of product or material use are
outside of ASM's control, ASM assumes no liability or obligation in connection with any use of this
information. As with any material, evaluation of the material under end-use conditions prior to
specification is essential. Therefore, specific testing under actual conditions is recommended.
Nothing contained in this publication shall be construed as a grant of any right of manufacture, sale,
use, or reproduction, in connection with any method, process, apparatus, product, composition, or
system, whether or not covered by letters patent, copyright, or trademark, and nothing contained in this
publication shall be construed as a defense against any alleged infringement of letters patent,
copyright, or trademark, or as a defense against liability for such infringement.
Extrusion: Second Edition Copyright © 2006 ASM International®
M. Bauser, G. Sauer, K. Siegert, editors, p 1-7 All rights reserved.
DOI:10.1361/exse2006p001 www.asminternational.org
CHAPTER 1
Introduction*
process is difficult to operate and the pressurized ment, modern control technology, and the opti-
fluid can withstand only relatively low tempera- mization of tooling materials and tooling design.
tures, which restricts the extrusion ratios that can Knowledge of the fundamental principles of
be achieved, the process has only limited appli- metallurgy, as well as the basics of deformation
cations in spite of initial great hopes. technology, machinery, and tooling, is needed to
In the conform process (Fig. 1.3), a contin- understand the extrusion process. All these as-
uous feedstock is extruded through the die by a pects are discussed in this book.
rotating friction wheel with a groove that is
closed by a semicircular shoe. Small cross sec-
tions and relatively low deformation ratios are
possible. Only a few applications are known.
The standard processes, i.e., direct and indi-
rect extrusion, have step by step reached high
levels of productivity and quality combined with
a simultaneous reduction in operating personnel Historic Development of
associated with improvements in machine tech- Extrusion*
nology and upstream and downstream equip-
Martin Bauser
by the piston B through a valve into the cylinder. Hanson, who, as early as 1837, were producing
The liquid material is then pushed by the piston lead tubes from a solid billet through a multipart
as split metal streams through annularly located bridge die with a replaceable fixed pressure pad
openings in the mandrel support so that the (Fig. 1.6).
metal streams combine and solidify in the an- The first two-piece container heated with gas
nular gap formed by the tube mandrel D and the was developed by Hammon in 1867.
tube support C to form a tube E. The start of electrification opened a new mar-
Pure lead melts at 327 ⬚C, and most of its ket for lead as a cable sheathing material. The
alloys at an even lower temperature, so that this first cable sheathing press was built by Borell in
material can be formed with low loads even at 1879 in which lead was extruded directly onto
80 ⬚C. Therefore, lead was the only important the cable core. The process was improved in
extruded material up to the end of the nineteenth 1882 by Werner von Siemens.
century. Many of the important elements of the Alexander Dick, who lived in England, suc-
process used today were, however, developed ceeded in developing from lead extrusion the
during this period. processing of metals with higher melting points.
The first known design of a (vertical) hydrau- He is therefore quite correctly considered to be
lic extrusion press for lead tube was developed the “father of extrusion.”
by the Englishman Thomas Burr in 1820 (Fig. In 1894, Dick registered a patent for an extru-
1.5). It had a container A, an extrusion stem with sion press designed specifically for brass rod
a machined-in pressure pad, a threaded mandrel, (Fig. 1.7) [Dic 94]. His idea was to cast liquid
and a replaceable die B. metal into the vertically orientated container and
England played a leading role in extrusion as to let it solidify. After rotating the container into
well as in many engineering fields. Lead pipes the horizontal position, the product was extruded
were used there relatively early for water supply from this initial heat through a replaceable die,
pipes. English inventions from the nineteenth F. Direct water pressure pushed the stem for-
century include the bridge die, the hydraulic ac- wards. A pressure pad protected it from the billet
cumulator, the gas-heated container, and the in- heat and prevented back extrusion of the metal.
direct extrusion process. Specific mention The die and die holder, E, were sealed against
should be made of the invention of I. and C. the cross head by two wedges, D. These were
Fig. 1.5 First hydraulic lead press (Th. Burr, 1820). A, con-
tainer; B, die; C, extrusion stem with machined
dummy block and threaded mandrel; D, extruded tube Fig. 1.6 First bridge die by I. and C. Hanson (1837)
4 / Extrusion, Second Edition
opened at the end of the extrusion process, and production. The water hydraulic extrusion press
the die discard and pressure pad ejected using was powered by a pressurized water system con-
the stem (Fig. 1.8). sisting of pumps and accumulators. The hot bil-
Because the one-piece container made from lets were manually loaded into the container us-
cast iron or steel tended to crack under the ther- ing tongs. Hand-operated valves were used to
mal stresses developed by the casting of the hot control the operating sequence of the extrusion
metal, a multipiece container was introduced in press. The extruded products had to be handled
1896. However, the individual cylinders were manually with tongs.
not prestressed but merely insulated from each Rapid developments at the start of the twen-
other by powdered graphite and borax. tieth century resulted in the extrusion process
The time-consuming process copied from completely replacing the previously standard
lead pipe extrusion of filling the container with process for the production of bars, sections, and
liquid metal was soon replaced by the use of wire in copper alloys of section by rolling of cast
preheated cast billets. Alexander Dick described billets. More than 200 extrusion presses, mostly
over a period of time many important details in for brass, had been built by 1918 (mainly by the
numerous patents: the loose pressure pad, vari- German company Krupp-Gruson). However,
ous mandrel designs for tubes, dies for multihole even steel sections were being extruded by 1914.
extrusion, and even a hollow section die. The Although it was possible to produce tubes on
three-piece bridge die patented by Alexander standard presses by the development of “floating
Dick in 1897 is shown in Fig. 1.9 [Dic 97]. The mandrels,” which were a loose fit in the hollow
billet is divided into six streams that weld to- billet and were heavily tapered toward the die,
gether in the shape forming aperture. this was replaced—following a patent by Arnold
The manufacture of extrusion presses with Schwieger in 1903—by a piercing system lo-
press capacities of more than 7 MN enabled cated behind the main cylinder (Fig. 1.10).
larger billets to be used, thus giving an economic The mandrel holder passing through the main
cylinder carries the mandrel at its tip, which can
pierce the solid billet. This then forms the inter-
nal contour of the tube in the die. These presses,
which can naturally also be used to extrude solid
bars by removal of the mandrel, were built up
to the 1950s. Then the internal piercer enabled
the press length to be shortened and the align-
ment of the mandrel to be improved (Fig. 1.11).
Fig. 1.7 First brass extrusion press. D, wedges; E, die and die
holder; F, replaceable die (A. Dick, 1894)
Fig. 1.8 Hydraulic extrusion press (1895) Fig. 1.9 Bridge die by A. Dick (1897)
Chapter 1: Introduction / 5
In the 1920s, experience showed that that the to improve the alignment of the press centerline,
concentricity of internal and external tube walls the guiding of the container, stem, and mandrel
was better on vertical hydraulic presses because to such an extent that tubes with adequate con-
of the favorable influence of gravity. The man- centricity were produced on horizontal presses.
drel was rigidly screwed to the stem and pre- In spite of the high cycle speeds, the presses with
pierced billets used. In the 1950s, numerous ver- a maximum capacity of 16 MN did not have
tical tube presses were built (by the companies sufficient power to process billets of sufficient
Schloemann and Hydraulik) but now with in- size.
dependent mandrel movement and automatic Around 1933, the vertical mechanical tube
operation for the production of copper and brass presses patented by Singer started to mass pro-
tubes. The manufacture of vertical presses duce steel tubes. These vertical tube presses with
stopped around 1965 when it became possible a high number of strokes per minute for the mass
production of steel tubes have been largely re-
placed by rolling processes that operate more
economically with a higher productivity.
Containers, which had for a long time been
produced as multipiece units but without any in-
terference fit could operate only with specific
press extrusion pressures of approximately 300
N/mm2. It was only the introduction of two- or
three-piece prestressed containers that enabled
higher extrusion pressures to be used. Movable
containers enabled the billet loading and the re-
moval of the discard to be improved. The intro-
duction of electric container heating (resistance
and later induction heating) in 1933 replaced the
previously used gas or coal heating and enabled
Fig. 1.10 First rod and tube press (Arnold Schwieger, 1903) aluminum to be processed (Fig. 1.12).
CHAPTER 2
Extruded Products
Günther Sauer*
THE HOT-WORKING PROCESS extrusion main applications of extrusion. This process can
is used to produce semifinished products in the also be used for certain copper alloys; however,
form of bar, strip, and solid sections as well as the materials used for the extrusion tooling can-
tubes and hollow sections. The high mean com- not withstand the thermo-mechanical stresses.
pressive stresses in the deformation zone of the Billet-on-billet extrusion enables coiled tubes of
container enable materials to be worked that long length to be produced, for example, alu-
cannot be processed into semifinished products minum alloy heat exchanger tubes and tin and
by other hot-working processes, for example lead alloy multicore solders.
rolling, because of their limited workability. The The extrusion process generally produces a
extrusion process also enables semifinished semifinished product close to the finished size
products to be produced from powder metal- with materials with working temperatures up to
lurgy-based materials, composite materials, and 600 ⬚C. This occurs in one production step in
the production of semifinished products from contrast to other processes used to form semifin-
clad composites with material combinations in- ished products. Therefore, the design of the
cluding aluminum/copper and aluminum/steel cross section of the semifinished product can
using the cladding process. Finally, the sheath- practically ignore any limitations associated
ing of electrical cables with lead or aluminum with subsequent processing operations. The
alloys using the transverse extrusion process has most suitable cross-sectional geometry can be
been a standard process for a long time, as has freely selected for the specific application. Sim-
the production of multicore solders with inte- ple matching of the cross-sectional geometry of
grated flux cores using the same process. the extrusion to the static, dynamic, and geo-
The pushing of the material being extruded metric requirements combined with the wide
through the shape-forming aperture of the extru- range of joining methods in assembly character-
sion die enables cross-sectional shapes to be pro- ize the high functionality of the products pro-
duced that cannot be manufactured by any other duced by this working process.
hot-working process. The favorable deformation
conditions with nonferrous metals such as tin
and lead alloys as well as magnesium and alu- 2.1 Tin and Lead Extruded
minum alloys with good welding properties and Products with a Deformation
working temperatures that can be withstood by Temperature Range of 0 to 300 ⬚C
the tool materials also enable the billet to be di-
vided into several metal streams, and then re- Tin alloy extruded products are mainly soft
welded in the shape-forming region of the ex- solders with or without flux cores for use in elec-
trusion die to form tubes and hollow sections. trical engineering and electronics. Tin alloys are
The production of hollow sections is one of the significantly more common than are lead alloys.
*Extruded Products from Materials with a Working Temperature Range of 600 to 1300 ⬚C, Martin Bauser
10 / Extrusion, Second Edition
They are produced on horizontal presses and The high density makes lead alloys particularly
drawn, coiled, or wound to the customers’ de- suitable for radiation and noise protection. Good
sired finished sizes on multispindle wire draw- workability combined with low melting points
ing machines as shown in Fig. 2.1. The produc- means that lead alloys are also used for the man-
tion processes are described in section 5.3. Other ufacture of soft solder, which is described in sec-
extruded products are anodes used for electro- tion 5.3. Lead alloys, similar to tin alloys, are
chemical plating with tin, for example, tin plat- also suitable for the production of custom
ing for corrosion protection. Tin alloy extruded shaped anodes as shown in Fig. 2.2 for electro-
products are also used in the manufacture of chemical plating. An example is the approxi-
chemical equipment. mately 20 lm thick and soft running surface in
Lead alloy products have lost a large part of plain bearings such as bearing shells and bushes.
their market since World War II because of the Although the use of specific lead alloys for the
toxic properties of these alloys. Even in the production of cable sheaths cannot be classified
1950s, extruded lead alloys were still used for as environmentally harmful, the cable industry
water supply pipes up to the fittings on sinks. prefers alternative plastic and aluminum-base
These materials were also used for extruded wa- materials. High-voltage cables are still sheathed
ter waste pipes. This has changed completely. in lead. Spacers for double glazing (Fig. 2.3) are
Lead alloys may no longer come into contact also extruded from lead alloys. Fishing nets and
with food products because they can form very curtains are usually weighted with lead lines
poisonous lead salts. Drinking water counts as a produced by horizontal extrusion. Some exam-
food and, therefore, lead drinking water pipes ples are shown in Fig. 2.3.
are no longer permitted. Nevertheless, lead al- Lead alloys can be made relatively resistant
loys offer a range of advantages that make al- to corrosion by the addition of tin. They can also
ternative materials difficult or even impossible be recycled relatively easily. However, the en-
to find. Lead alloys have good resistance to vironmental political pressure will affect the cur-
fluoric and sulfuric acids as well as phosphoric rent applications because of the toxic properties
acid, ammonia, chlorine, and soda. They are of this material.
therefore useful alloys for the chemical industry.
Fig. 2.2 Extruded sections and tubes in lead base and tin al-
Fig. 2.1 Soft solder with one or more flux cores (tube solder), loys for use as anodes for the electrochemical coat-
extruded and drawn to the finished dimensions and ing, supply tubes for aggressive media, materials for seals and
coiled on plastic spools. Source: Collin radiation protection, etc. Source: Collin
Chapter 2: Extruded Products / 11
minum extrusion tools. This has played a same round container by using spreader tech-
decisive role in the development of the design niques. West European aluminum extrusion
of extrusion tooling for aluminum profiles. Very plants today can produce extruded sections rang-
demanding aluminum profiles can now be pro- ing from 10 g/m to 130 kg/m. The section “Ex-
duced. In recent years, the development of ex- trusion of Semifinished Products in Aluminum
trusion tools for the production of large profiles Alloys” describes the extrusion processes used
has been particularly successful. today for aluminum alloys.
Large profiles are used today in almost all ar- The large profile technology was first devel-
eas of industry. In Europe alone there are four oped in the second half of the 1970s for the con-
large extrusion presses with press powers of struction of railway rolling stock. Until then, the
72,000 to 100,000 kN used to produce them. technical advantages of aluminum aroused some
Standard solid and standard hollow sections interest in its use as a construction material, but
with a circumscribing circle diameter of approx- the classic method of construction of railcar
imately 600 mm can be produced from 650 mm body shells using sheet and small extruded pro-
round containers on the 98,000 kN direct extru- files could not compete with the proven con-
sion press operated by Alusuisse in Singen (Ger- struction material steel. A light steel design of
many) (Fig. 2.7). Solid flat sections with maxi- the body shells was about 50% cheaper than a
mum dimensions of 800 by 100 mm (width by comparable one made from aluminum alloys.
height) and flat hollow sections with a maximum The light steel construction was, therefore, pre-
size of 800 by 60 mm can be produced from the ferred. This changed with the introduction of
Fig. 2.7 Large sections produced from containers with a circular bore on the 98,000 kN direct extrusion press in Singen. Adapted
from Alusuisse
14 / Extrusion, Second Edition
large profiles the length of the rolling stock that a higher alloy content) do not offer the same
could be automatically welded to each other. profile geometry options as the low alloyed
The assembly cost of the railcar body shells and easily welded aluminum alloys such as
could be reduced to an extent that not only com- AlMgSi0.5 and AlMgSi0.7.
pensated for the higher material cost of the alu- Figure 2.9 shows a body shell of the Paris
minum but also reduced the total cost of the alu- Metro type MF 77 utilizing welded large profile
minum wagon by approximately 30% of that of technology. The carriage cross section is shown
the steel wagon [Wis 92, Cor 95]. in Fig. 2.8, together with some of the large pro-
Aluminum designs using large profiles that files necessary for its construction. Figure 2.10
simplified assembly then started to compete with shows the right longitudinal rib needed to stiffen
steel. Today, aluminum large profile technology the floor frame of the carriage of the San Fran-
has become the economic solution in many cisco Metro in the alloy AlMgSi0.7 on the run-
branches of technology. Large profiles enable out table of the 98,000 kN direct press in Singen,
several fabricated classic components to be re- Germany.
placed. Extruded profiles can be supplied as in- Since the introduction of the integral con-
tegral components ready for installation. Large struction utilizing large section technology, alu-
profiles not only can replace several classic com- minum designs can increasingly compete with
ponents but also, in addition to their static and steel designs in spite of the higher material cost
dynamic functions, take on additional functions of the aluminum. The specific properties of alu-
in addition to the overall function with the min- minum alloys play a role here including the low
imum of additional material as shown in Fig 2.8, E-modulus of the various alloys and their low
which depicts cross-sectional views of a carriage density. Whereas the E-modulus of aluminum
of the Paris Metro [Alz 85]. alloys can be assumed to be approximately 70
The mechanical properties of the aluminum GPa, that of steel is approximately 210 GPa,
alloys used for the production of large aluminum three times as high. At the same time, the alu-
profiles are adequate for most applications minum designs can be given the same stiffness
where good design enables the profile geometry as steel designs to avoid unacceptable bending
to be adequately dimensioned. Nevertheless, dif- or vibrations with significantly lower weights
ficult to extrude and, to some extent, moderately because of the low density of 2.7 g/cm3. In ad-
difficult to extrude aluminum alloys (those with dition, the elastic properties of aluminum de-
Fig. 2.8 Shell of a type MF77 carriage of the Paris Metro, self-supporting in welded large section technology (Alsthom Atlantique/
Alusuisse, 1977/1981) manufactured in sections from the age-hardened material AlMgSi0.7. a, Multifunctional longitudinal
stringer; b, construction of the carriage body in the roof longitudinal stringer region; c, weld joint geometry between the individual
extruded sections; 1, multifunctional longitudinal stringer; 2, section in roof region with extruded weld preparations; 3, longitudinal
stringer to ensure adequate stiffness of the floor group; 4, door mechanism; 5, rainwater gutter extruded on section 1; 6, door seal
location extruded on section 1; 7, roof closure section; 8, roof internal cladding; 9, floor section with extruded legs for the welded joints
as well as extruded center locations; 10, floor group sections with extruded slip seating for tolerance equalization; 11, section view of
the floor sections with extruded locations for bolt heads. Source: Aluminium Zentrale
Chapter 2: Extruded Products / 15
signs offer significant advantages. Aluminum al- one of the largest North American Railway com-
loys have significantly higher elastic or energy panies, had built for them, excluding the con-
absorption capacity relative to steel because of ventional locomotive design, an aluminum ex-
their low E-modulus. This is an advantage that ample of the semistreamlined steam-powered
should not be undervalued for aluminum designs “Royal Blue,” traveling between Chicago and
subjected to impact loads, for example, in rail or St. Louis [Hug 44]. Only the wheel trucks, cou-
road transport vehicles. plings, and buffers of the eight passenger cars
were made in steel, all other components from
alloys of the alloy group AlCuMg. Long ex-
2.2.2.1 Transport Construction truded profiles were used for the load-carrying
Rolling Stock. Efficient low-weight rolling components of the car underframe. Even the col-
stock has always been of interest to railway op- umns of the side walls were made of extruded
erators. Low weights provide higher load capac- profiles, which were also used for the necessary
ities with lower energy consumption and enable stiffening in other places in the carriage. Formed
higher vehicle accelerations when starting and sheets in the same aluminum alloy were used for
higher vehicle deceleration on braking, as well the cladding of the carriage walls, for the train
as a reduction in rail wear. These advantages are car roof as well as for the floor.
mainly utilized by local traffic with its many Sections and sheet were joined together with
stops, e.g., underground trains, but also by long rivets and arc welding. In addition, the internal
distance traffic, in particular, high speed rail fittings of the carriage, for example, the tables
traffic. and seats in the dining car, also were made from
Toward the end of the 1920s, the transfor- aluminum alloys. The eight carriages built com-
pletely from aluminum had a total weight of 350
mation of weight reduction in rolling stock re-
metric tons in contrast to the identically con-
sulted in the replacement of steel internal fittings structed steel carriages with 650 metric tons, i.e.,
by fittings made in aluminum alloys, initially in 54% of the weight of the steel carriages.
passenger carriages. However, in 1934, the Bal-
timore and Ohio Railroad Company, at that time
Fig. 2.11 Diesel power car of the Trans Europa Express (TEE) on the Rhine section
which set a world record of 515 km/h (320 mph) Ing 91]. Further development resulted in interest
on test runs. In the next 20 years in Europe, a in the aluminum large profile technology for the
certified rail network for high-speed trains with multiunit railcars for the high-speed rail traffic.
multiple current systems and corresponding sig- In this period, the percentage of rolling stock
nal and control systems will develop in Europe produced using large aluminum alloy profile
to allow inter-European long-distance trains to technology increased out of proportion. At the
travel the national rail networks. These stretches start of the 1970s, it was approximately 5% but
are operated for inter-European long-distance has now increased to over 60% [Ing 91].
train travel with train concepts that do not follow Whereas the French high-speed train TGV of
the previously conventional train system of “a the SNCF with its respectable power and proven
locomotive with carriages.” One example is the ability over several years was manufactured in
Eurostar, a special design of the TGV with a steel, the German Railway decided to build its
multiple current system that can travel between 280 km/h (175 mph) high-speed trains InterCity
Paris and London in three hours through the Express 1 (ICE1) and InterCity Express 2 (ICE2),
Channel Tunnel. The ICE3 of the DB follows a as well as the 330 km/h InterCity Express 3
similar concept. (ICE3), and the 230 km/h InterCity Express T
From this perspective, the European railway (ICET), basically using self-supporting welded
operators have a vital interest in trains with the large aluminum profile technology. The only ex-
lowest possible weight for the high-speed rail ception was the power cars of the trains ICE1
network as described previously. Low weights and ICE2, which were manufactured in steel to
minimize the energy requirements for powering ensure that the driven four axles per power car
these trains as well as the wear of the tracks and could apply sufficient normal force onto the
permit high accelerations when starting and de- track to obtain the torque needed to achieve high
celerations on braking. acceleration and deceleration.
The big breakthrough for the economical ap- This, however, results in high track loading
plication of aluminum alloys in carriage con- because each wheel truck of these power cars
struction was the development of the large pro- places a load of 40 metric tons onto the rails.
file technology in the 1970s by Alusuisse. This Throughout Europe, however, the track can only
enabled rolling stock to be entirely and eco- be loaded to a maximum of 34 metric tons per
nomically produced from aluminum at a signifi- wheel truck. For this reason, the two high-speed
cantly lower cost than comparable rolling stock trains ICE1 and ICE2 cannot use the inter-Eu-
in steel lightweight construction. This involves ropean rail network. This, however, changed
the use of easily extruded, relatively corrosion with the introduction of the high-speed train
insensitive, and easily age-hardened aluminum ICE3, which in contrast to the power car train is
alloys such as AlMgSi0.5 and AlMgSi0.7, with- designed as a multiunit train; i.e., the driven
out which the very demanding cross-sectional axles are spread along the entire train with every
geometries of the large profiles could not be pro- second axis being driven. These trains apply a
duced. These extrusion alloys also provided sig- load less than 34 metric tons weight on the track
nificant freedom in the design of the cross sec- per wheel truck and are therefore suitable for
tion to match the strength needed in the participation as multisystem trains for the Inter-
component. Until now, this could not be European traffic [Tas 93]. The InterCity Express
achieved with moderate to difficult to extrude T (ICET) is in certain ways a special design of
alloys used previously in the manufacture of the ICE3 fitted with tilting technology devel-
rolling stock. Modern concepts were also devel- oped in Italy. With this design, the multiunit
oped for the steel lightweight designs of rolling train can travel around curved rails with high
stock, but these could not significantly reduce speed. Figure 2.13 shows an example of the
the price advantage of the aluminum large pro- ICE1 framed with a schematic diagram of the
file technology [Aug 77, Wis 92]. The rolling extruded profiles for the floor group, the longi-
stock produced from welded large profile tech- tudinal member of the floor group, and the con-
nology also offers weight advantages over those necting edge wall profile of the left side of the
produced from the high-strength steels. Both passenger carriage. The joint aids visible on the
these factors resulted in the extensive applica- section corners in Fig. 2.13 for the longitudinal
tion of the aluminum lightweight construction joining of the extruded sections are of interest.
incorporating the large profile technology in Eu- Finally, Fig. 2.14 describes the design of the
rope and the United States in the 1980s [Dav 79, passenger carriage with all the large profiles for
18 / Extrusion, Second Edition
Fig. 2.13 High-speed ICE1 of the Deutsche Bahn AG framed by the large sections of the carriage cross section shown in Fig. 2.14.
Source: Alusuisse
the left half of the carriage. In addition, Fig. 2.15 the aim of reducing transport energy costs. For
shows a view of the design of the passenger car- a long time, there has been increasingly rigorous
riage of the high-speed trains ICE2 and ICE3. competition with other methods of transport, in-
Other European national railways, for exam- cluding road transport. Initially, this involved in-
ple, Denmark, England, Italy, and Norway, as creasing the load capacity of the freight wagon
well as Spain and Sweden, have learned the by using individual, usually movable, aluminum
value of the self-supporting aluminum large pro- alloy components for the same wagon axle load.
file technology in welded designs for high-speed Consideration was then given to significantly
trains as well as intercity passenger carriages improving the handling of the construction ele-
and intercity rail cars. This technology has, for ments. Sliding roofs, folding roofs, as well as
example, been used for building the 250 km/h sliding doors and shutters, were manufactured
(155 mph) high-speed Advanced Passenger from aluminum sheet and reinforced with ex-
Train of British Rail and the 300 km/h (185 truded sections by the German railway, DB, as
mph) ERT 500 of the Italien Ferrovie dello Stato well as the Swiss Federal Railway, SBB. With
(FS). The French TGV Duplex, a double decker, time, complete wagon bodies also were built
new high-speed train of the SNCF, will be man- from aluminum alloys. The structure of these
ufactured using welded aluminum large profile wagons consisted of roll formed 1.5 to 2.0 mm
technology to control the track loading. thick AlMg3 sheets reinforced with AlMgSi0.5
Self-supporting large profile aluminum tech- extruded sections, apart from the under frame
nology is used not only for high-speed trains and the vertical end wall columns, which were
running on rails. The carriages of the track made in steel. In addition, the aluminum con-
guided fast magnetic levitation Transrapid, with struction offers not only the advantage of weight
a maximum speed of 500 km/h (310 mph) are reduction but is also maintenance friendly, i.e.,
built using the self-supporting aluminum large in contrast to steel designs, no painting is needed
profile technology in a bolted design [Mil 88]. because of the corrosion resistance of the alu-
The prototype is shown in Fig. 2.16. This assem- minum alloys used.
bly method is described in the section “Bus Tilting sidewalls on open goods wagons for
Manufacture” later in this chapter. specific transport applications are manufactured
Naturally, thought has been given to reducing from AlMgSi0.5 and AlMgSi0.7 extruded pro-
the wagon weight in rail freight transport with files, as shown in Fig. 2.17. These sidewalls can
Chapter 2: Extruded Products / 19
Fig. 2.14 Passenger carrier design on the high-speed train ICE1 of the Deutsche Bahn AG with the large sections of the left carriage
section. Source: Alusuisse
be highly loaded and do not require any surface large distances. This process is usually carried
protection because of the corrosion resistance of out using rolling stock with the optimum load
the aluminum alloys. capacity. The optimum storage capacity of these
The focal point of European rail transport is wagons can be achieved by using self-support-
mixed cargo transport where the loading space ing welded aluminum large profile technology,
of a wagon is more important than the load- which makes them particularly economical
carrying capacity. Consequently, the application compared with wagon designs in steel. Figures
of aluminum alloys is usually limited to movable 2.18 and 2.19 show an example of a coal silo
components as described previously. Bulk goods wagon built with aluminum large profile tech-
transport by rail has only a limited role in Eu- nology. The sidewalls as well as the chassis of
rope. this coal silo wagon consist mainly of large
This differs in other countries, including extruded profiles in the aluminum alloy
Australia, Canada, South Africa, and the United AlMgSi0.7 with large format sheets of
States, with, for example, rich surface reserves AlMg2.7Mn in the floor area. The assembly of
of coal and minerals. The extraction site is usu- the silo wagon involves the use of the same
ally a long distance from the processing plant automatic welding systems that are used for
so that bulk goods have to be transported over personnel carriages.
20 / Extrusion, Second Edition
Silo wagons of this design were designed and load is approximately 10% less than that of a
built by Alusuisse to U.S. standards. In spite of steel wagon.
the high material costs of the aluminum silo Road Vehicles. The development of auto-
wagons, their manufacturing cost per ton pay- mobile manufacture including both cars and
Fig. 2.15 (a) Carriage shell cross section ICE2 and (b) carriage shell cross section ICE3, self-supporting using welded large section
technology. Source: ADtranz
Fig. 2.16 Prototype of the magnetic levitation Transrapid manufactured with bolted aluminium large profile technology using
aluminium AlMgSi0.7 extruded sections. Source: Alusuisse
Chapter 2: Extruded Products / 21
Fig. 2.17 Tilting trailer walls of an open goods wagon finished in extruded hollow sections in the alloys AlMgSi0.5 and AlMgSi0.7.
Source: Alusuisse
Fig. 2.18 Coal silo wagon produced in welded self-supporting large extrusion technology to U.S. standard. Source: Alusuisse
freight vehicles has been associated with the use After World War II, this development in-
of aluminum alloys from the beginning. Alu- creased rapidly. The use of aluminum alloys in
minum gearbox and motor housings were al- road vehicles increased continuously. Today, af-
ready being reported in the latter years of the ter steel, aluminum alloys are the most important
nineteenth century. In 1924, the Swabische Hüt- material in the manufacture of automobiles. In
tenwerk developed a car with a self-supporting 1993, in Germany alone 315,000 metric tons of
aluminum design. In 1937, BMW fitted the well- aluminum were used in the manufacture of cars
known two-seater sports car 328 with an alu- and 58,000 metric tons in freight vehicles [Gor
minum alloy body. In racing car manufacture, 94]. The main applications of aluminum are
the well-known Silver Arrow manufacturer castings for engine and gearbox housings, pis-
Auto Union, BMW, and Mercedes Benz used tons, and cylinder heads, as well as car wheels.
aluminum alloys to produce the lightest chassis It is also used as a semifinished product in the
possible. Toward the end of 1920s, the first form of sheets or strip for the manufacture of
buses with aluminum bodies were built, particu- bonnets and boot lids, water and oil coolers, and
larly in Switzerland (Fig. 2.20). also sometimes for complete sports cars bodies
22 / Extrusion, Second Edition
Fig. 2.19 Design and construction of the coal silo wagon shown in Fig. 2.18
Fig. 2.20 Older bus body manufactured from aluminum alloys in Switzerland with a frame in extruded sections. Source: Alusuisse
as well as extruded semifinished profiles for the consumption by about 0.6 to 0.8 l/km (in-
production of trim and widow frames, and for creases mileage 3.5 to 4.7 mpg).
safety components such as side-impact beams in ● Lower environmental pollution from exhaust
car doors. Car superstructures and bus bodies, gases as a result of the reduced fuel con-
goods vehicle superstructures, and sidewalls, in sumption.
addition to forgings for the manufacture of ● Reduction in maintenance costs due to the
wheels and engine components, are also made better corrosion resistance of the aluminum
from aluminum. This increasing use of alumi- alloys
num alloys provides these well-known advan- ● Simple recycling of the aluminum alloys
tages to the automobile industry: used as secondary aluminum
● Lower vehicle mass and thus savings in mo- Passenger Cars. In 1958, Opel in Germany
tive energy, i.e., fuel. According to [Her 90], introduced the Rekord shown in Fig. 2.21 as a
the replacement of 200 kg of steel by 100 kg new design to the market. The car had as a new
of aluminum in a car reduces the gasoline feature for the European automobile industry
Chapter 2: Extruded Products / 23
window frames in extruded and age-hardened years, high demands were placed on the deco-
aluminum alloy for the front and rear wind- rative appearance, in particular, on the optimum
screens, as well as the side windows in the doors. polish. Good mechanical properties were also
The aluminum frames were attached in such a required. The top of the door consisted only of
way to the steel sheet that the top of the door an aluminum frame, and this frame should not
consisted only of the window frames with the bend when the door was closed. Aluminum ex-
window glass, as shown in Fig. 2.21. The ex- truded profile window frames appeared in many
truded profiles that formed the frames were de- car models for over a decade. During this period,
signed in such a way that the rubber sections that between 150,000 and 200,000 metric tons alu-
sealed against the body could be easily located minum sections flowed into this project. Car
in the aluminum window frames. The extruded manufacturers finally stopped using this deco-
profiles were formed to the window frames on rative aluminum window frame construction on
stretch bending machines, welded together, the doors mainly because of the wind noise be-
ground, and polished and anodized to a thick- tween the window frame and the body associ-
ness of 4 to 6 lm. The section material used by ated with the rapidly increasing speeds. The
Opel was initially Al99.8ZnMg and, later, cause of the wind noise was the speed-related
Al99.8MgSi. suction forces acting externally on the window
Opel introduced this design within Germany surfaces and also the pressure forces from the
following pressure from the United States. The operation of internal fans on the inside of the
design was quickly adopted by Audi, BMW, and window surfaces. This revealed a weakness in
Ford. The aluminum alloy solution heat treated the aluminum window frame design. As a con-
during the billet heating was extruded into water sequence of the E-modulus of the aluminum al-
(standing wave). The sections had a weight per loys used for the window frames being one-third
meter of only 0.150 to 0.850 kg. In the early that of a suitable steel, the aluminum window
frames deformed elastically three times as much
as a steel frame of the same design. Profile cross
sections with higher moments of inertia could
not easily be incorporated into the door design.
This did not exclude, however, the further use
of extruded profiles as frames for the front and
rear car windscreens, as shown, for example, in
the E class Mercedes in Fig. 2.22. In addition,
numerous extruded profiles are used in car bod- cross-sectional geometry and sufficient proof
ies for a wide range of applications, including stress and elongation are particularly suitable for
steering wheel adjustment, seat rails, sliding roof this application [Fra 89]. A correctly designed
guides, and also for water and wind deflectors impact beam in an extruded aluminum alloy
in the roof area of the body and side window with materials properties comparable to a geo-
guides. Figure 2.23 depicts the metal frame for metrically similar steel impact beam can possess
the folding top cover of the SL class made from approximately three times the elastic deforma-
an extruded profile. tion capability before plastic deformation oc-
Aluminum extruded profiles are particularly curs.
suited in special cases for the manufacture of Interest in the extruded age-hardened alumi-
safety components for the automobile because num alloy side-impact beam combined with a
the cross-sectional shape can be exactly matched
to the loading. They also offer favorable me-
chanical properties and density and the low E-
modulus as well. A typical example is the side
door beam that can fulfill its role in a very func-
tional way. Side impact causes 30% of all road
deaths in 25% of all car accidents in Germany.
The car sides cannot be protected for space rea-
sons by crumple zones as, for example, used in
the front and rear. Therefore, the car manufac-
turers have over the years made great efforts to
protect the sides of cars using effective side-
impact beams as well as air bags. Figures 2.24,
2.25, and 2.28 show this technology in Audi ve-
hicles.
The impact beam must be able to absorb the
transmitted impact energy from an impact on the
side door over a defined deformation displace-
ment without breaking, buckling, or even dis-
placement in order to protect the passengers. Re-
search results have shown that extruded
aluminum alloy profiles with a symmetrical
Fig. 2.24 Side door of the Audi 100 with built-in chroma-
tized for corrosion protection, extruded section in
the aluminum alloy AlMgSi1, F 31 with RP0.2 ⳱ 260 N/mm2 and
A5 ⳱ 10%. Source: Alusuisse
side air bag is increasing because the good However, in cars this did lead to weight reduc-
physical and mechanical properties, in particu- tions of about 60 kg in Europe and about 80 kg
lar, the elastic behavior, enable the safety re- in the United States. The desire for larger weight
quirements to be fulfilled. Many automobile savings now has resulted in greater use of light
manufacturers are now installing them. materials. In the future, engine and gearbox
Naturally, there are numerous safety compo- housings will be made primarily from aluminum
nents that are manufactured from extruded alu- alloys. Car manufacturers are also replacing
minum profiles. Figure 2.26 shows a steering load-carrying steel automobile components with
linkage in which the left-hand link consists of aluminum. This gives an additional weight sav-
sections of extruded profiles, whereas the flexi- ings of 60 to 70 kg and a definite improvement
ble right-hand part is manufactured from impact in the ride because of the significantly lower un-
extruded tube sections with formed bellows. In damped weights.
an accident, the bellows deform so that the im- Meanwhile, the automobile driver has be-
pact on the steering column is reduced. The come increasingly more demanding. The stabil-
good experience obtained with the deformation ity of the body, the airbag, and the side-impact
behavior of side-impact beams made from ex- beams, ABS and effective crumple zones pro-
truded age-hardened aluminum hollow sections vide passenger protection. In addition, air con-
has now been used in automobile plastic bumper ditioning, CD systems, navigation systems, and
beams with integrated aluminum hollow sec- other luxurious fittings should make traveling in
tions in the alloy AlMgSi0.5 or AlMgSi0.7. a car as pleasant as possible. Simultaneously, the
These sections naturally have to match the pro- fuel consumption should decrease and the ma-
file of the bumper beam, i.e., they have to be terials from old vehicles be easily recycled.
bent. Whereas this bending operation is carried In the future, these conflicting demands will
out today on a large scale on stretched extruded be met by the use of light body designs in steel,
profiles with significant cost for the bending, de- aluminum alloys, improved magnesium alloys,
pending on the section geometry, possibly fol-
and to a limited extent by fiber-reinforced plas-
lowed by a sizing operation, these deformation
tic, if necessary, up to self-supporting structures.
processes can be carried out in the United States
As early as 1950, Pakiney built the DYNA
during the extrusion process. The low hot flow
PANHARD car with extensive use of AlMg3
stress of the aluminum alloy aids the bending
sheet and, later, AlMgCu. The car weighed only
process.
The introduction of defined and legally re- 650 kg and was extremely economical. In 1990,
quired targets of weight saving, energy saving, Honda developed the sports car NSX with
and simple recycling of the materials used has AlMgSi1 sheet, and Rover has used for many
initiated significant innovations in recent years years in the Land Rover aluminum sheets for the
in the automobile industry. Previously, alumi- body; initially, AlMgCu and, today, AlMgSi1
num alloys were generally used for simple parts. [Alp 94]. The decisive step was made by AUDI
AG with the production of the AUDI A8 shown
in Fig 2.27. The body is made entirely of alu-
minum.
This breakthrough of aluminum into the steel
domain has both shocked and challenged the
wide strip manufacturers (body sheet). They are
trying to counter this development with intelli-
gent solutions for complete steel chassis, for ex-
ample, with the use of prefinished body parts,
tailored blanks. Tailored blanks are cut to size,
designed for the load, body panels laser welded
together from steel sheets of different thickness,
strength, and surface quality. These prefinished
Fig. 2.26 Steering link in the alloy AlMgSi1, F 31. The con- body parts, for example, complete wheel hous-
nection on the left-hand side is from an extruded
section, whereas the round, easily deformed in the event of a ings, enable assembly costs and also weight to
crash, corrugated section with the transition to the steering col- be reduced. This is the start of a process that
umn was manufactured from an extruded tube. The corrugated
region is heat treated to a strength of F 22 to F 25. Source: Alu-
should finish with the ultralight steel car body.
suisse However, the high point of this development to-
26 / Extrusion, Second Edition
day is the Audi A8 and the Audi A2 with the the age-hardening alloys AlMgSi0.5 and
space frame construction of Alcoa. This con- AlMgSi0.7. Supporting floor panels consist of
struction principle can be seen in Fig. 2.27 to the age-hardening alloy AlMgSi1Cu, small
2.29. Audi uses for the production of the alu- sheet parts from the non-heat-treatable alloy
minum body aluminum alloys containing the AlMg5Mn. The die cast nodes necessary for
same alloying elements, a basic requirement for joining the preformed and age-hardened ex-
ease of recycling. The extruded sections needed truded profiles to balance out the tolerances for
to assemble the space frame are produced in the space frame of the Audi A8 were manufac-
Fig. 2.27 Audi A8 Quatro with a body of age-hardened aluminum alloys using the Alcoa space frame concept. Source: Audi
Fig. 2.29 Space frame of the Audi A2 in extruded sections, sheet and castings. Source: Audi
tured with the vacuum casting process in the els that harden during this heat treatment. The
heat-treatable alloy AlSi10Mg. Other cast com- sections of the space frame heat more slowly
ponents consisted of AlSi7. Die cast components because these are shielded by the body outer
for tolerance compensation were not used for the skin during the heat treatment. For this reason,
space frame of the A2. the bent profile sections for the space frame have
Finally, cold-worked strip sections in the flow to be supplied age-hardened in such a way that
line free (Lüders lines) and heat-treatable alu- they harden only slightly during the age-hard-
minum alloy AlMg0.4Si1.2 were used as exte- ening process described and do not over age. In
rior body panels. Table 2.1 provides an overview particular, the softened peripheral zones of the
of the materials used to build the aluminum body section welded from the MIG welding should as
of the Audi A8. far as possible reharden. The complete alumi-
The automobile manufacturer joins the deliv- num body of the Audi A8 is approximately 200
ered prefinished and age-hardened profile sec- kg lighter than a conventional steel body of the
tions to assemblies by MIG welding with the aid same size.
of jigs. The complete space frame is then built Bus Manufacture. The manufacture of buses
using the same joining technique. The floor pan- from aluminum alloys has a tradition in Swit-
els and, in particular, the 1.0 to 1.15 mm thick zerland, as shown in Fig. 2.20. The Alpine coun-
sheets for the body exterior skin were fixed us- try started to consider the reduction in weight of
ing other joining techniques including, among goods vehicles in the 1920s. The engine powers
others, self-piercing rivets. Finally, the finished available at this time were still very limited and
body in white is age-hardened at a temperature could therefore be better utilized with a lower
of 230 ⬚C for 30 min. It is mainly the body pan- weight. The Swiss with their mountainous re-
Table 2.1 Aluminum alloys used for the aluminum body of the Audi A8
Material AA(a) Temper Rp0.2 (N/mm2)(b) Rm N/mm2(c) A5 %(d)
Sheet AlMg0.4Si1.2 6016 T6 200 250 14
AlMgSi1Cu 6009 T6 230 280 10
AlMg5Mn 5182 ... 135 270 25
Vacuum die casting AlSi10Mg ... T6 120–150 180 15
Permanent mold casting AlSi7 ... T6 200 230–250 15
Extruded section AlMgSi0.5/0.7 ... T6 210–245 1.08 Rp0.2 11
(a) Aluminum Association designation. (b) Rp0.2 is 0.2% proof stress. (c) Rm is tensile strength. (d) A5 is elongation after fracture. Source: Audi
28 / Extrusion, Second Edition
gions never lost sight of this basic principle; it this system are in operation today in Switzer-
increased in importance after World War II. land, Denmark, and Norway. System-built bus
Other countries, including Germany, also be- superstructures are also common in the United
came interested in these solutions. States with sidewalls in extruded sections simi-
Extruded profiles in aluminum alloys were the lar to those used today in Europe for railway
natural solution for the economical lightweight rolling stock [Alp 94].
construction of buses. Their low density and More than a decade ago, Alusuisse developed
good mechanical properties, as well as the op- a bolted bus superstructure with good results.
timum shape-forming capability combined with The nucleus of this aluminum bus superstructure
the use of modern joining techniques, provided is the bolted corner elements as shown in Fig.
not only the prerequisite for economic designs 2.32, which, combined with the system sections,
of bus superstructures but also for a rational provide for simple assembly. After successful
transport of the passengers. trials in their own country, other European coun-
The bus construction concept is based in prin- tries became interested in the process. The two
ciple on a lattice frame design of extruded alu- companies Schweizerische Aluminium AG and
minum sections similar to the space frame of the the German company Kässbohrer presented to
Audi A8 (Fig. 2.28). These profiles are welded the International Automobile Association (IAA)
in 1987 a study commissioned by the Ministry
together as shown in Fig. 2.30. The body panels
for Research and Technology of a bus manufac-
are attached with suitable joining techniques.
tured of aluminum using the bolted design under
Buses built entirely of aluminum according to
the name SETRA CONCEPT BUS. This bus is
shown in Fig. 2.31 and the design of the bolted
corner joints of the Alusuisse system M5438 in
Fig. 2.32.
The bolted design of the supporting aluminum
lattice frame had considerable advantages over
a similar welded design. The bus superstructure
can be produced extremely economically and
quickly without labor-intensive reworking as a
result of welding distortion. There is also the
advantage for the vehicle owner that accident
repairs can be carried out in a relatively short
time and to a relatively high quality. This assem-
bly system has been successful in many coun-
tries. Moreover, the Swiss have also used this
method of assembly for light rolling stock for
passenger traffic. The carriage bodies of the ex-
perimental vehicles of the magnetic levitated
Transrapid described in the section “Rolling
Fig. 2.30 Old lattice design for coach construction as shown
Stock” and Fig. 2.16 are built from bolted ex-
in Fig. 2.20 manufactured from extruded alumi-
num sections. Source: Alusuisse truded aluminum sections.
Fig. 2.31 The study of a coach presented at IAA 1987 with bolted, supporting lattice frame construction in extruded aluminum
sections. Source: Alusuisse
Chapter 2: Extruded Products / 29
Fig. 2.33 Typical aluminum hollow sections for goods vehicle sides in the alloy AlMgSi0.5. Source: Alp 94
30 / Extrusion, Second Edition
The use of aluminum alloys for truck and Planked superstructures in extruded alumi-
trailer constructions for the transport of bulk num sections have also proved successful as
goods and liquids has proved to be particularly shown in Fig. 2.37. In spite of the higher ma-
economic, for example the silo rolling stock in terial costs for aluminum alloy designs, these are
Fig. 2.18. This also applies to coarse bulk goods viable because of the increase in load capacity
transported with road vehicles. Silo trailers are derived from the weight saving. In contrast to
frequently manufactured entirely from alumi- other European countries, in Switzerland, the
num alloys. The chassis of the trailer is fre- planked trailers are made completely from alu-
quently manufactured from extruded aluminum minum, including the load-carrying parts of the
sections. In Europe, silo and liquid transporters chassis. In the United States, the use of alumi-
predominantly use this type of aluminum super- num alloys for goods vehicles raises fewer ques-
structure [Koe 88]. Figure 2.35 also shows a tions than in Europe.
loose-goods vehicle for building sites, with a tip- The use of aluminum components made from
ping aluminum body made in AlMg4.5Mn extruded semifinished hollows for superstruc-
sheets with transverse reinforcement (round tures as well as chassis, but also from strip and
spars) of extruded AlMgSi1 sections. Finally, sheet for the manufacture of containers and
Fig. 2.36 shows a trailer with a covered tipping wheel rims and so forth, will increase in the fu-
body made entirely of aluminum sections. All ture for goods vehicles. The aim is an optimum
aluminum tipping body shells have low wear. low vehicle weight with optimum carrying ca-
Fig. 2.34 Five-core hollow section for goods vehicles sides with a width of 530 mm and a height of 25 mm and a six-core side
section 800 mm wide and a height of 25 mm manufactured in AlMgSi0.5, F 25. Source: Alusuisse
Fig. 2.35 (a) Tipping wagon with welded tilting body in aluminum sheet reinforced with round spars of extruded aluminum sections.
Source: Alusuisse. (b) Tilting body from (a) constructed from: 1 and 2, sheets of AlMg4.5Mn; 3, extruded aluminum curved
section in AlMg4.5Mn; 4, round spar with AlMgSil extruded aluminum sections and a cross-sectional geometry of 4.1: 5, top edge in
extruded aluminum section
Chapter 2: Extruded Products / 31
pacity. Aluminum is well suited for this. Finally, in the future the dominating metallic-base ma-
the recycling of the used aluminum from old, terial for the manufacture of aircraft in the form
no longer usable goods vehicles is relatively of plate, sheet, extruded sections, and cast com-
simple. ponents. Aluminum alloys still have potential
Aircraft manufacture is one of the oldest ap- for further development. The aircraft outer skin
plications of aluminum. As early as 1897, alu- will still be made from aluminum alloys. Im-
minum-base materials were used for the con- portant parts of the wings, stiffeners in the shape
struction of airships, and age-hardening of spars and stringers are also made from high-
aluminum alloys enabled the German aircraft strength aluminum alloys as well as window
manufacturer Junkers to introduce the complete frames, connection nodes, and landing gear
metal airplane (Ju-4) in 1917. Whereas today, components, including the forged aluminum
certain components of modern aircraft such as wheel rims. However, in spite of their being the
elevators, rudders, and landing flaps are made dominant materials used, the trend is for the use
from specific weight saving and carbon fiber- of aluminum alloys in the entire Airbus fleet to
reinforced plastics (CFP), aluminum will remain reduce, as shown in Fig. 2.38. Carbon fiber-
Fig. 2.36 Tipping trailer with covered body made entirely from extruded multicore hollow sections for the transport of fine pow-
dered goods. Source: Alusuisse
Fig. 2.37 Trailer with planked construction and chassis in extruded aluminum sections. Source: Alusuisse
32 / Extrusion, Second Edition
reinforced plastic materials do have a lower den- fuselage in the form of stringers. Figure 2.39
sity and much higher mechanical properties, but shows stringer profiles as longitudinal stiffening
they also have a high impact crack sensitivity of an airbus fuselage where the external skin is
with low ductility and toughness. Moreover, produced from roll clad aluminum sheets in the
their manufacture involves complex production alloy 2024. Extruded sections are used for the
and quality control processes. They are therefore seat rails and the floor transverse supports. The
correspondingly expensive [AlH 71, Alt 88, Alp latter can also be easily seen in Fig. 2.39. The
94]. cross-sectional geometry and the relative size of
Extruded sections are used in aircraft in dif- the extruded profiles used are shown in Fig.
ferent places for load-carrying or reinforcement 2.40. Spars for transverse stiffening of the fu-
functions. For example, they are used as longi- selage skin as shown in Fig. 2.39 are made from
tudinal stiffeners for the sheet skin of the aircraft AA2024 strip.
Fig. 2.38 The percentage of metallic materials in the Airbus fleet. Source: Daimler Benz Aerospace Airbus
Fig. 2.39 Airbus fuselage cell with roll clad AA2024 sheet skin longitudinally reinforced with extruded stringer sections in AA2024
and with transverse reinforcement of spars in roll clad AA2024 sheet. The clearly visible cabin floor supports are man-
ufactured from AA7075 extruded sections. Source: VAW
Chapter 2: Extruded Products / 33
The fraction of extruded profiles within the aluminum industry has focused on the aim of
total of semifinished products used for aircraft producing high-strength alloys that can be hot
in the Airbus fleet is around 11%; in contrast to and cold worked. The alloy groups AlCuMg and
Boeing aircraft, where it is 41%. As Fig. 2.41 AlZnMgCu, as well as the new somewhat dif-
shows, with Boeing, the fraction of extruded ficult AlLi alloys, offer the aircraft industry alu-
aluminum profiles used dominates when com- minum alloys that can be statically and dynam-
pared with other semifinished products. With the ically loaded to high stresses and processed to
Airbus fleet, sheet forms the largest fraction. semifinished products by rolling, forging, and
Weight reduction also plays an important role extrusion. Aluminum alloys with high hot
in modern aircraft manufacture. The demand is strengths are also available for supersonic air-
for low-density materials with good mechanical craft [Alp 94].
properties that can be stressed optimally to the The classic aluminum alloys for aircraft con-
operating safety limit. Since Wilm’s chance dis- struction have been modified over the years and
covery in 1909 at the Dürener Metallwerke of their heat treatment so specialized that today,
the age-hardening capability of AlCuMg, the they not only achieve optimum materials prop-
Fig. 2.40 Extruded sections for the Airbus aircraft in aluminum alloys AA2024 and 7075. Source: Daimler Benz Aerospace Airbus
Fig. 2.41 Distribution of the semifinished products used in (a) the Airbus fleet compared with (b) the Boeing fleet. Source: Daimler
Benz Aerospace Airbus
34 / Extrusion, Second Edition
metric tons of aluminum. Modern large aircraft porting structures within the superstructures of
carriers require similar large quantities of alu- the ships.
minum semifinished products for their super-
structures. Finally, large section technology has 2.2.2.2 Machine Manufacture, Electrical
also been used for lightweight construction tech- Machines, and Electrical
niques in ship superstructures. The use of large
Equipment
profiles reduces the assembly costs.
Extruded large multicavity sections are used, The manufacture of machinery and electrical
for example, in ships in the fishing industry as machines was, for a long time, dominated by
rack floors with through flowing coolant for the iron-base materials, but with time this has
storage of fish in the cold rooms. Mobile inter- changed. Other materials with their favorable
mediate decks for ships for the transport of ani- properties are threatening the domination of the
mals can be produced from large aluminum pro- iron-base alloys. During the past 20 years, per-
files for economic reasons, as shown in Fig. sonnel costs have increased more rapidly than
2.46. The alloys AlMgSi0.5, AlMgSi0.7, and the material costs. Aluminum-base materials
AlMgSi1 are used for these and for the sup- with their very specific materials properties have
Fig. 2.46 Multicore hollow section for mobile intermediate ship decks for sheep transport. Source: Alusuisse
Chapter 2: Extruded Products / 37
today secured a respectable position in this field sections provide for electric motor housings
[Cor 95]. along with the functional related cross sectional
For a long time, the use of aluminum alloys geometry:
in machine manufacture was restricted to the
● A large heat-conducting housing surface
smaller components that could be produced by
with extruded cooling fins with significantly
casting, forging, stamping, or even extrusion.
narrower spacings and thinner wall thickness
The future emphasis for manufacture with alu-
than cast housings
minum alloys will be on the large section tech-
● Integrated cooling channels depending on re-
nology. This gives the designer a new design
quirements as shown in Fig. 2.47
element to be used to achieve optimum technical
● An extruded material with high strength and
and economical solutions [Alp 94]. The load and
good elongation significantly superseding
functional related shape capabilities of these ex-
the mechanical properties of the earlier cast
truded profiles as well as the high dimensional
housings
accuracy have revolutionized many designs, as
● Housing material not susceptible to corro-
shown in the examples depicted in this section.
sion
Low density and good mechanical properties
make aluminum alloys interesting for moving Electric motor housings with extruded feet,
machine components with high accelerations cooling fins, and cooling channels can literally
and decelerations. Nonmagnetic properties, as be obtained as finished components by cross cut-
well as good thermal conductivity, ensure that ting the extrusion. Even with small or moderate
aluminum alloys play an important role in the production runs, the manufacturing costs of the
manufacture of electrical machines and electri- extruded motor housings are well below those
cal equipment. Electric motor housings belong of cast aluminum housings. Bus bars (Fig. 2.48)
to the most important aluminum products in the from aluminum sections with pressure clad and,
electrical industry, as shown in Fig. 2.47(a). more recently, mechanically bonded layers of
Weight advantages, free choice of shape, and the ferritic steel are produced to supply S and U
good thermal conductivity of low-alloyed alu- trains.
minum materials have resulted in aluminum re- The options of large section technology in-
placing cast iron and steel for electric motor clude the assembly simplifying large section
housings [Joh 85, Tas 93]. Extruded aluminum showed in Fig. 2.49 for the tool carrier of a ma-
Fig. 2.47 AlMgSi0.5 extruded section for electric motor housings (a) and a large section for the console of a high-speed printer
(b). Source: Alusuisse
38 / Extrusion, Second Edition
chining center as well as the carrier and housing chines, fixtures, and transport systems can
section for the scanner of a carpet tufting ma- therefore make a significant, and perhaps even
chine in Fig. 2.50. Frequently, the aluminum the most important, contribution to the entire de-
profile leaves the extrusion plant as a ready-to- sign. Last but not least are the significant eco-
install machine component, i.e., application and nomic advantages that make aluminum sections
function specific extrusion, age-hardened, and eminently suitable for the manufacture of ma-
cut to length. In this sense, the aluminum large chines and electrical machines as well as for the
section can practically be conceived as a finished manufacture of numerous traditional products.
system component for simple installation. The Large section technology and integral design re-
cross-sectional geometry of the extruded section duce the assembly costs. They replace complete
can be almost ideally matched to the function steel designs with one section and thus eliminate
and loading, and the lattice geometry of the ex- many manufacturing steps.
trusion profile makes the large section very sta- Using a hot circular saw and a food slicing
ble and stiff. Aluminum large sections for ma- machine for sausage and cheese as examples,
Fig. 2.50 AlMgSi0.5 support and housing sections for the scanner of a carpet tufting machine. Source: Alusuisse
Chapter 2: Extruded Products / 39
Fig. 2.51 Application of large sections in the alloy AlMgSi0.5 for (a) the table of a wood circular saw and for (b) the table of a food
slicer. Source: Alusuisse
Fig. 2.51 illustrates the ideal way an extruded tion matched aluminum extruded sections de-
section can be matched to the function of a ma- signed as a section for the manufacture of elec-
chine and its operation [Als Pr]. trical pneumatic control units. Rotor blades of
The large section shown in Fig. 2.52 for the wind electrical generators are usually made from
manufacture of fixing plates for pneumatic con- multicavity hollow sections. Extruded alumi-
trol elements shows an example of these capa- num sections dominate as the supporting ele-
bilities. Figure 2.53 demonstrates the cost sav- ments in transport systems such as modular
ing, production technological possibilities as transfer systems, linear vibration conveyors, and
well as the process technical advantages of func-
Fig. 2.52 Cross section of an 800 mm wide large section in Fig. 2.53 Aluminum section in the alloy AlMgSi0.5 for the
the alloy AlMgSi0.5 for the production of fixing manufacture of electropneumatic control units.
plates for pneumatic control elements. Source: Alusuisse Source: Alusuisse
40 / Extrusion, Second Edition
2.2.2.3 Architecture
Buildings. The destruction of the West Eu-
ropean cities initiated a building boom in the 50
years after World War II. Large quantities of
building elements including windows and doors
were needed. Many new commercial buildings
Fig. 2.54 Extruded blanks in AlMgSi0.5 for rotors of the air as well as offices were fitted with aluminum
compressor of a pneumatic tanker pumping unit cladding, which had been seen in the United
for sewage. Source: Honsel
States.
This accelerated the penetration of aluminum
into building. In addition, architects appreciated
so forth. It is not only aluminum large sections the silver metal.
that have proved to be advantageous for ma- Since then, large quantities of aluminum
chine design, small sections can also offer sig- semifinished products are consumed by the
nificant advantages, for example, the extruded building sector. Today, aluminum is one of the
blanks for the rotor of an air compressor. The most important materials in buildings. Over the
slots to receive the vanes are extruded in the years the metal has gained a specific market
section. Figure 2.54 shows this quite clearly. The with its decorative surface finish and its good
slots have to be milled out of the blanks in steel corrosion properties. Today, the building sector
rotors.
Pure aluminum and low-alloyed aluminum al-
loys including AlMgSi0.5 are good conductors
of heat. Extruded tubes and sections in these ma-
terials are therefore used for heat exchangers and
cooling elements. Nests of tubes made from ex-
truded pure aluminum are required in large
quantities in the chemical, petrochemical, and
food industries. In air conditioners, small, flat
multicore hollow sections are used. Tube sec-
tions are used in recuperative and regenerative
systems, including heat exchangers and also so-
lar panels. The use of hollow sections in con-
densers for liquid nitrogen tanks is well known.
The high-power electronic industry requires
high-power cooling bodies as shown installed in
Fig. 2.55. Using separately extruded base and
finned sections joined together by a rolling pro-
cess in which the finned sections are firmly
rolled with their feet in the slot of the base sec-
tion, high-power cooling elements are manufac- Fig. 2.55 Example of a heat sink in the alloy AlMgSi0.5 for
the cooling of the thyristors of a compact disc
tured as shown in Fig. 2.56 [Tas 93]. player
Chapter 2: Extruded Products / 41
Fig. 2.56 Various high-efficiency heat sinks constructed from extruded AlMgSi0.5 elements to remove the heat produced from
electronic systems. Source: Alusuisse
alone accounts for 15% of the total aluminum compared with steel has to be considered in
consumption of Germany and is therefore the the context of fire prevention measures. The
second largest consumer of this material after AlMgSi-base metallic construction materials
the transport sector [Alz 97]. The main appli- have a solidus temperature of only about 580 ⬚C.
cations are the door and window sectors as
well as building façades, followed by roofs,
internal walls, conservatories, and building en-
trances.
Aluminum façades are usually used for im-
posing buildings, for example, large retail stores,
company head offices, and large bank buildings
and official buildings. Over time, specific flexi-
ble building systems have been developed that
can be easily installed. The base structure of ex-
truded sections provides the support for the fa-
çade and is usually invisible after installation.
Aluminum-base structures can also be used for
building façades in other materials.
The high strength of the aluminum alloys
used in building applications enables ambitious
filigree but reliable designs to be produced.
However, when this material is used with other
materials, such as steel, the different physical
properties of the materials have to be taken into
account. In particular, the significantly lower E-
modulus and the higher linear coefficient of ther-
mal expansion of aluminum have to be allowed
for. Also, the lower solidus temperature of the Fig. 2.57 Skyscraper of the Dresdner Bank in Frankfurt, Ger-
aluminum alloys used in high-rise buildings many, with a naturally anodized aluminum façade
42 / Extrusion, Second Edition
Fig. 2.62 Ekonal-FV70 aluminum glass façade system from Erbslöh-Aluminium for the Neuss fire station in Hammerdamfeld. The
steel framework for fixing the façade is shown by the double T beam on the right-hand side of the drawing. Source:
Erbslöh-Aluminium
Fig. 2.63 Refurbishment of the NCR at Spree-Ufer in Berlin, Germany, with the blue baked painted aluminum window frames
Chapter 2: Extruded Products / 45
Fig. 2.64 Insulated glass window with thermal break in the more stable than those produced in plastic. Ex-
aluminum section. A typical hollow aluminum truded aluminum sections are usually used for
section is used as the spacer between the two panes of the double
glazing. The frame of the window has two brown plastic bars to
the closures of flat roofs and frequently for win-
reduce extensively the heat conduction. Source: Hueck dowsills on house external walls. Extruded sec-
tions are valued in buildings, and the interna-
tional development of buildings shows a
and undulating structures can be produced eco- corresponding increase in the use of aluminum
nomically. for architectural applications.
Roller shutter and sectional doors in extruded The refurbishment of curtain walling, win-
aluminum sections for fire stations and hospitals dows, and doors can produce large quantities of
and transport companies (Fig. 2.69) also depend aluminum as building scrap. This scrap can be
on the beneficial properties of the alloys used. easily melted like that from machines, automo-
Aluminum shutter doors last longer and are biles, and rolling stock, and converted to sec-
Fig. 2.65 Extruded spacers for the double glazed windows shown in Fig. 2.64. Source: Erbslöh-Aluminium
46 / Extrusion, Second Edition
and loading. The aluminum semifinished prod- bers in West Germany in the 1960s in extruded
uct supplies a specialized market, although the AlZn4.5Mg1 and AlMgSi1 bear impressive wit-
use of aluminum-base building materials is not ness to the advantageous use of aluminum alloys
so marked by spectacular designs and buildings in specific cases. Equally, the use of extruded
as is steel [Alp 94]. However, aluminum pedes- aluminum sections in civil engineering is ver-
trian bridges, pedestrian drawbridges as well as satile, for example, the manufacture of movable
gangways for ships, planking for quays and, in steps for airports and static industrial steps as
particular, the Bailey bridges built in large num- can be seen in Fig. 2.70 to 2.72. Extruded sec-
Fig. 2.74 Helicopter landing platform manufactured from aluminum alloys with the multicore large section shown as the supporting
profile with multifunctions including integrated fire extinguisher foam pipe in the upper part of the section. Source:
Alusuisse
Fig. 2.75 Assembly of the supporting profiles shown in Fig. 2.74 for the helicopter landing platform. Source: Alusuisse
Chapter 2: Extruded Products / 49
tions are also suitable for the manufacture of tions, with copper alloys extrusion is used in
conveyor systems (Fig. 2.73). The load carrying most cases as the preliminary step for subse-
parts of marquees are usually made from ex- quent cold-drawing operations (with intermedi-
truded aluminum semifinished products, and ate annealing when necessary), which produce
movable lifting platforms depend on their light the finished dimensions of the required products
telescopic aluminum arms. Even in underground sold by the semifinished product plant—bar,
workings, reusable extruded aluminum form- wire, section, and tube.
work is preferred. The German standards list almost 90 wrought
For some time, aluminum large-scale con- copper alloys. In addition, there are numerous
structions have been used in offshore applica- special custom alloys. This clearly illustrates the
tions. Their use for accommodation modules wide range of alloys and the fine differentiation
and helicopter landing decks, as shown in Fig. to be found in copper and copper alloy specifi-
2.74, is related to the good physical and, in cations. This, together with the large dimen-
the marine atmosphere, good corrosion resis- sional range of the semifinished products pro-
tance of the aluminum alloys used along with duced by section and tube extrusion, makes it
the good assembly options of the large alu- impossible to describe all applications.
minum sections and, thus, the favorable assem- The copper alloys are divided into the groups:
bly costs. The helicopter landing deck in Fig.
● Pure copper
2.74 and 2.75 gives an impressive illustration
● Low-alloy copper
of this. Similar advantages are shown by the
● Copper zinc alloys (brass), also with addi-
use of extruded semifinished products in suit-
tional elements (special brass)
able alloys for display signs on freeways and
● Copper-tin alloys (tin bronze)
main roads in the salt-laden atmosphere during
● Copper-aluminum alloys (aluminum bronzes)
the winter.
● Copper-nickel alloys
● Copper-nickel-zinc alloys (German silver)
The high electrical and thermal conductiv-
ity—for pure copper, both are the highest of all
metals—the alloy dependent more or less good
Extruded Products from workability at room temperature (cold worka-
bility) or at high temperature (hot workability),
Materials with a Working the corrosion resistance against different media,
Temperature Range of 600 and the decorative appearance are decisive fac-
tors in the selection of suitable alloys. With this
to 1300 ⬚C wide range of positive properties, extruded cop-
per alloys can be found in an extremely wide
Martin Bauser* range of industrial products—often only as a few
individual parts such as electrical contacts in
household machines. Copper alloys form the
major component in only a few products, for
example, bathroom fittings, some decorative
2.3 Copper Alloy Extruded Products metal products, or brass instruments.
In the past few decades, a large part of the
The temperatures used for the extrusion of market for copper alloys has been partly or com-
copper alloys are 600 to 900 ⬚C, significantly pletely lost. One example is cutlery, which pre-
higher than those for aluminum alloys. Conse- viously was largely made from silver or chro-
quently, only semifinished products with simpler mium-plated brass and nickel silver and which
cross-sectional geometries and thicker-walled is now almost exclusively stainless steel. An-
sections can be produced because of the more other example is in electronics, in which relays
severe thermal loading of the shape-producing fitted almost exclusively with copper alloys have
tools. Whereas extruded sections form the been replaced as switching elements by elec-
“lion’s share” of all extruded aluminum sec- tronic components.
Plastics are now used to a large extent for zip-
*Extruded Products from Materials with a Working Tem- pers and ball point pens, although a small market
perature Range of 600 to 1300 ⬚C, Martin Bauser remains for high-value products. There are other
50 / Extrusion, Second Edition
Fig. 2.77 Bar, shaped bar, and turned components in free machining brass. Source: Wieland-Werke AG
Chapter 2: Extruded Products / 51
ufacture bolts, nuts, and other small parts is The severe competition by plastic for the use
CuZn39Pb3 (Fig. 2.77). of brass shaped wire for zippers has already been
Household water fittings can be produced mentioned. However, even today, metal is some-
from extruded bars of the hot-working alloy times preferred for high-quality applications.
CuZn40Pb2 by hot stamping followed by ma- This also applies for many parts in equipment in
chining. Bars in other copper alloys including daily use, where to some degree there has been
special brasses and copper-nickel alloys are ma- a return to metallic materials, which retain their
chined to fixing elements and so forth where cor- shape even after prolonged use and also are less
rosive attack is feared. likely to break.
Fig. 2.78 Brass extruded sections. Source: Wieland-Werke Fig. 2.79 Furniture fittings in extruded brass sections.
AG Source: Wieland-Werke AG
Fig. 2.80 Brass section extruded sections. (a) Terminal blocks. (b) Lock cylinders. Source: Wieland-Werke AG
52 / Extrusion, Second Edition
chines, mechanical engineering, power stations, II. Today, copper tubes are converted from the
and automobiles because of their good wear and extruded shell to the finished product by numer-
corrosion resistance. They are also being used ous drawing operations on rotary drawing ma-
to an increasing extent as piston gudgeon pin chines. However, plastic pipes recently have
bearings in engine manufacture (Fig. 2.83). started to compete against copper tube in low-
The largest use of copper tube extrusion by quality water because of copper solubility and
far is the manufacture of copper tubes for do- occasional corrosive attack.
mestic water tubes (Fig. 2.84). The oxygen-free Copper tubes have also made their mark in
copper SFCu has gradually almost completely heating and air conditioning applications where
replaced steel and lead pipes since World War tubes are used for under-floor heating, radiator
Fig. 2.83 (a) Bearing bushings in extruded special brass. (b) As installed
Fig. 2.84 Extruded and drawn copper tube in straight lengths and coils
54 / Extrusion, Second Edition
connections, and tubes in air-conditioning plants tubes on roll machines, depending on the appli-
(Fig. 2.85). The tubes are purchased in straight cation. These finned tubes are also made in other
lengths or small coils from the semifinished materials (special brasses and copper nickel) if
product manufacturer for domestic applications, the medium in which they are used is corrosive
although large coreless coils with a preferred (Fig. 2.86).
weight of 130 kg are used for industrial appli- In sanitary applications, water outlet com-
cations (Fig. 2.84). ponents are preferred in lead-free brass tubes;
Finned tubes are more suited for heat ex- this is also due to the outstanding plating
changer tubes than tubes with smooth surfaces. characteristics with nickel and chromium (Fig.
Different fin shapes are formed from smooth 2.87).
Fig. 2.85 Domestic insulation and under-floor heating in extruded and drawn (plastic-insulated) copper tubes. Source: Wieland-
Werke AG
Fig. 2.86 (a) Tube coils and finned tubes in extruded copper tubes. (b) Test stand for finned tubes. Source: Wieland-Werke AG
Chapter 2: Extruded Products / 55
ample, saltwater. Their good skin compatibility with corrosive media—frequently associated
as well as their visual appearance makes ex- with high temperatures—are the reason stainless
truded titanium alloys useful as the starting ma- steels of suitable composition are used in the
terial for the manufacture of glass frames and chemical and petrochemical industries, power
watch housings. For the same reason, titanium stations (both fossil fired and also nuclear), and
alloys are used for the manufacture of implants in marine technology. Extremely high specifi-
and surgical tools [Mec 80, Alp 94]. cations frequently have to be fulfilled and evi-
Titanium alloys have certainly not reached dence of numerous quality tests provided be-
their full potential because of their good prop- cause of the high safety requirements and the
erties. Their further development from the point long service life demanded.
of view of even higher thermo-mechanical load- The same hot-working processes used for
ing and more economic production will open stainless steels are also used for nickel-alloy
other areas of application. Titanium alloys also tubes as well as high-alloy high hot strength ma-
lend themselves to recycling. terials. However, in these applications, extrusion
plays a significantly more important role than
with stainless steels, because only small quan-
tities in very precisely alloyed materials are usu-
2.5 Extruded Products in Iron Alloys
ally required and the price of the very high re-
and Other Hot-Working Alloys quirements is not the controlling factor.
A wide range of applications of nickel alloys
Various hot-rolling processes threaten the is found in the chemical and petrochemical in-
market in extruded iron alloy semifinished prod- dustries, in turbine and jet engine manufacture,
ucts. Only a few segments remain for extrusion, in aerospace, ship construction, and the food in-
where the geometry of the extrusion, the special dustry.
alloy, or the small demand is preferred to the Whereas tubes produced by extrusion usually
other processes geared to high throughputs in consist of high-alloy and difficult to hot-work
standard alloys and standard shapes. alloys, easily worked versions are preferred for
Extruded volume steel tubes—previously the the extrusion of profiles to enable useful cross
staple extruded product—have not been pro- sections to be produced. The extrusion tempera-
duced on presses for some time. The production ture is approximately 1250 ⬚C so that the shape-
of round and shaped bars is also moving away producing tools can withstand only low extru-
from extrusion. sion pressures and are so deformed after only
With stainless steels, high-alloy ferritic and one extrusion that they have to be reworked.
austenitic steels are extruded as tubes. Down- Subsequent stretching and correction operations,
stream cold pilger and drawing operations bring possibly calibration and brightening drawing
the tubes to the final dimensions required by the operations, give the section the final shape.
customer. The severe requirements associated Higher-alloyed and thus difficult to extrude
stainless steels can be extruded only into the
simplest shapes (Fig. 2.89).
Fig. 2.89 Extruded stainless steel tubes. The thin wall sec-
tions that can be seen under the extruded sections Fig. 2.90 Special sections as support tubes in a walking
are produced by roll forming. Source: Krupp-Hoesch beam furnace for heating steel slabs
Chapter 2: Extruded Products / 57
[Mec 80]: E. Meckelburg, Eigenschaften and [Tas 93]: W. Taschner, Mit Aluminium in die
Anwendung von Titan als Konstruktion- Elektrotechnik (Aluminum in Electrical En-
swerkstoff (Properties and Applications of Ti- gineering), Ing.-Werkst., Vol 5 (No. 4), 1993,
tanium as an Engineering Material), Maschi- p 72–73
nenmarkt,Vol 86 (No. 9), 1980, p 154–158 [Tas 93]: W. Taschner, Mit Aluminium auf die
[Mil 88]: L. Miller, Einsatz von Alumini- Schiene (Aluminum on the Railway), Ing.-
umwerkstoffen für moderne Verkehrssysteme Werkst., Vol 5 (No. 3), 1993
(Application of Aluminum Alloys to Modern [Tec 96/97/98]: Techn. Universität Clausthal/
Transport Systems), Aluminium, Vol 64 (No. Universität Hannover, Sonderforschungsber-
1), 1988, p 24–28 eich 1515 Magnesiumtechnologie (Special
[Ren 97]: K.H. Rendigs, C. Melzer, and G. Bro- Research Project 1515 Magnesium Technol-
den, Aluminium Strangpreßprodukte im Air- ogy Financial Support Contract), Finanzi-
bus (Extruded Aluminum Sections in the Air- erungsantrag, 1996/97/98
bus), Vortragstexte des Symposiums [Wis 92]: G. Wisniewsky, Metall, Schlüssel-
STRANGPRESSEN, Vol 9 and 10, Oct 1997 werkstoff in der Umformtechnik (Metal, Key
in Garmisch-Partenkirchen, DGM-Informa- Material in Deformation Technology), Ing.-
tionsgesellschaft, Verlag Werkst., Vol 4 (No. 11), 1992
Extrusion: Second Edition Copyright © 2006 ASM International®
M. Bauser, G. Sauer, K. Siegert, editors, p 59-139 All rights reserved.
DOI:10.1361/exse2006p059 www.asminternational.org
CHAPTER 3
THE ROD AND TUBE extrusion processes Rod extrusion is discussed first, while tube
can initially be classified into cold-working and extrusion is considered later.
hot-working processes: The rod extrusion process can be divided into:
● Cold working: The material being processed ● Direct extrusion
is not heated, i.e., loaded into the working ● Indirect extrusion
process at room temperature. ● Hydrostatic extrusion including the thick
● Hot working: The material being processed film process
is heated to a temperature above room tem- ● Special processes, e.g., the conform process
perature and then loaded into the working and cable sheathing
process. Figures 3.1(a) and (b) show the direct and in-
As hot working is the standard process in rod direct extrusion process versions discussed in
and tube extrusion, the terminology usually used this book. Figure 3.1(c) lists both hydrostatic ex-
is rod and tube extrusion instead of hot rod ex- trusion processes described in the book, and Fig.
trusion and hot tube extrusion. 3.1(d) shows the special processes covered in
The cold rod and tube extrusion processes are, the book.
however, always referred to as such, which em- It should be pointed out that only the pro-
phasizes that they are special processes. cesses that are of practical importance are dis-
In rod extrusion wire, strip, bar, solid sections, cussed. Variations that do not appear to be im-
and hollow sections are produced. The latter are portant for the future are deliberately excluded.
extruded through welding chamber dies. In The processes mentioned in Fig. 3.1(a) to (d)
these, the material is welded in the deformation are described individually. The direct extrusion
process within the die. This is referred to as ex- process is considered first. There are, in princi-
trusion welding. In hollow sections it produces ple, four versions according to Fig. 3.1(a). The
the extrusion weld seam. Tubes produced in this extrusion of aluminum and copper alloys are
way are considered under rod extrusion. used as examples in the discussion of direct and
Tube extrusion is referred to, however, when indirect extrusion. The thermal conditions that
seamless tubes are produced using a mandrel occur in hot copper alloy extrusion are signifi-
passing through the billet to produce the internal cantly different from those in hot aluminum al-
contour and a die for the external contour. loy extrusion.
Rod extrusion is the extrusion of wire, strip,
sections, bars, and hollow sections through a die. 3.1 Direct Extrusion
Tube extrusion is the extrusion of seamless
tubes as well as seamless hollow sections over Direct extrusion is the extrusion process used
a mandrel passing through the billet. most frequently. The main application of the
*Hydrostatic Extrusion, Gottfried Schreiter; Conform Process, Klaus Siegert; Cable Sheathing, Martin Bauser; Tube Extrusion
Process, Klaus Siegert
60 / Extrusion, Second Edition
direct extrusion is the extrusion of semifinished important direct extrusion processes discussed
products of aluminum. However, all other me- in this book.
tallic materials including steel, copper, brass, The process can be divided into direct extru-
lead, and zinc can be deformed by the direct sion with lubrication and direct extrusion with-
extrusion process. Fig. 3.1(a) depicts the most out lubrication, depending on whether there is a
Fig. 3.1 (a) Direct extrusion processes. (b) Indirect extrusion processes. (c) Hydrostatic extrusion processes. (d) Special extrusion
processes
Chapter 3: Rod and Tube Extrusion Processes / 61
film of lubricant between the material being de- proximately the same as the container tempera-
formed and the tooling: ture R.
This is only a basic statement. Temperature
● Direct extrusion with lubrication: There is a
changes in direct hot extrusion are discussed in
film of lubricant between the material being
Sections 3.1.1.5, 3.1.2.5, and 3.1.3.4.
deformed and the tooling.
Approximately 80% of the extrusion process
● Direct extrusion without lubrication: There
direct extrusion without lubrication and shell in-
is no film of lubricant between the material
volves aluminum alloys. If aluminum extrusion
being deformed and the tooling.
is mentioned, this usually means the direct hot
As shown in Fig. 3.2, in direct extrusion with- extrusion of aluminum alloys without lubrica-
out lubrication, the material being deformed is tion and shell.
loaded as a billet between the container and the
stem, pushed along with the pressure pad by the
stem into the container, upset in the container, 3.1.1.1 Process Sequence of Direct Hot
and then pushed through a stationary die. The Extrusion without Lubrication or
die aperture determines the external contour of Shell
the section.
The process-defining feature in direct extru- There are principally two possible methods of
sion is the friction between the material being loading the pressure pad:
deformed and the container because the upset According to Fig. 3.2, the billet is loaded with
billet is pushed during extrusion in the container the pressure pad between the stem and the con-
toward the die. tainer and then pushed into the container by the
Characteristic feature of direct extrusion: stem. Alternatively, the pressure pad can be
friction between the material being de- fixed to the stem. Figure 3.3 shows the sequence.
formed and the container. As mentioned pre- The actual extrusion process starts with the
viously, the direct hot extrusion process is first upsetting of the billet in the container. The pro-
described using direct hot extrusion of alumi- cess stops when the discard length lR is reached.
num alloys as an example. This is followed by The container then opens a short distance so that
the direct hot extrusion of copper alloys. Hot the discard can be separated from the die and the
extrusion of aluminum alloys is usually carried extrusion by a shear blade. The extrusion can
out without lubrication and shell (Fig. 3.2). then be pulled from the die. The container and
Direct hot extrusion without lubricant with a the stem (with a loose dummy block) or the con-
shell is considered in section 3.1.2 using the di- tainer, the stem and the fixed dummy block are
rect hot extrusion of copper alloys as an exam- then returned to the starting position.
ple. In billet-on-billet extrusion, the extrusion is
usually cut by a shear or a saw located behind
3.1.1 Direct Hot Extrusion without the end housing (Fig. 3.4).
Lubrication and Shell (Aluminum
Alloys) 3.1.1.2 Variation in the Extrusion Load
Hot extrusion is, according to the German with Stem Movement in Direct
Standardization Institute (DIN), when the billet Hot Extrusion without Lubrication
is loaded into the container at a temperature or Shell
above room temperature. Usually, the billet in
hot extrusion is heated to a temperature above As shown in Fig. 3.5, when the billet is upset
the recrystallization temperature of the billet ma- in the container, the extrusion load FSt increases
terial. The container, die, and pressure pad are to a maximum value FSt max. The actual defor-
also heated to approximately the same tempera- mation process commences at this value. When
ture, providing the thermal properties of the the extrusion leaves the die, the billet in the con-
tooling permit this. The maximum permitted op- tainer moves toward the die by an amount cor-
erating temperature for hot-working steels is ap- responding to the volume extruded. If the extru-
proximately 500 C. sion ratio V is the ratio of the container
Aluminum alloys can be extruded above the cross-sectional area A0 to the product cross-sec-
recrystallization temperature under the follow- tional area AS and the ram speed is uSt, then the
ing conditions: The billet temperature B is ap- speed of the extrusion uS is given by:
62 / Extrusion, Second Edition
Fig. 3.2 Process sequence of direct hot extrusion without lubrication and without a shell, with loose dummy block. a, platen; b,
die holder; c, die; d, container; e, billet; f, dummy block or pressure pad; g, extrusion stem
Chapter 3: Rod and Tube Extrusion Processes / 63
Fig. 3.3 Process sequence of direct hot extrusion without lubrication and without a shell, with dummy block fixed to the stem. a,
platen; b, die holder; c, die; d, container; e, billet; f, dummy block or pressure pad; g, extrusion stem
64 / Extrusion, Second Edition
Fig. 3.4 Billet-on-billet direct hot extrusion without lubrication and without a shell, with dummy block fixed to the stem. a, platen;
b, die holder; c, die; d, container; e, billet; f, dummy block; g, extrusion stem; h, discard from the previous extrusion
Chapter 3: Rod and Tube Extrusion Processes / 65
Fig. 3.5 Variation of the stem load FSt over the stem displacement s St in direct hot extrusion without lubrication and without a shell
(initial billet temperature B 艑 container temperature R). lB, initial billet length; DB, initial billet diam; l0, upset billet
length; D0, container diam; sS, shear stress; s, stem displacement; lR, discard length; B, initial billet temperature; A, container tem-
perature; uSt, stem speed
66 / Extrusion, Second Edition
Fig. 3.7 Determination of the velocity field of the distorted network [Wil 69] visio-plastic material flow investigation
68 / Extrusion, Second Edition
Fig. 3.9 Material flow zones in direct hot extrusion without lubrication and without a shell. A, primary deformation zone; B,
secondary deformation zone; C, friction affected peripheral zone; D, dead metal zone; E, billet core; a, container; b, die;
c, die holder; d, dummy block; e, stem; f, extrusion
Chapter 3: Rod and Tube Extrusion Processes / 69
Dürrschnabel [Due 69] defined the following tween the billet and the die surface. The friction
principal material flow types as shown in Fig. between the billet and the container results in
3.11. the outer layer of the billet being held back rela-
Flow type S is based on the assumption of tive to the billet interior. The dead metal zones
negligible friction between the billet and the are more marked than with type A. The defor-
container as well as between the billet and the mation zone then encompasses a significantly
die front surface, and is also based on the as- larger billet area.
sumption that no shear zones form in the billet. Flow type C is formed by the same friction
With these assumptions and homogeneous billet conditions as type B but in this case the differ-
material, the material being deformed must ence is an inhomogeneous billet. This occurs
move across the die front surface and the billet when the flow stress of the billet outer zones is
surface becomes the surface of the extrusion. significantly higher than that of the billet core.
Flow type S is purely theoretical and does not Severe cooling can result in the billet outer zone
occur in practice. having a lower temperature than the billet core.
Flow type A applies to homogeneous billet This occurs when the container temperature is
materials, low friction between the billet and the much lower than the initial billet temperature.
container as well as significant friction between With certain materials, e.g., (␣-b) brass, phase,
the billet and the die front surface. It is charac- differences are possible as a consequence of the
terized by a “dead metal zone” that forms in low temperature of the billet outer zones, such
front of the die and a narrow shear zone between as b brass (body-centered cubic lattice) in the
the dead metal zone and the billet. This shear billet interior and ␣ brass (face-centered cubic
zone approximates to a funnel that borders the lattice) in the billet outer zones. The billet pe-
primary deformation zone. The billet zones out- riphery of material with the higher flow stress is
side this funnel are not influenced by the defor- restrained relative to the billet core, builds up in
mation. The material volume at the billet surface front of the dummy block, and is diverted into
can flow via the shear zone into the outer regions the billet interior with further extrusion finishing
of the extrusions. up under the extrusion surface in the center of
Flow type B applies to homogeneous billet the product. This material flow results in a sec-
materials, significant friction between the billet ondary “deformation zone.” The result is an ex-
and container as well as significant friction be- trusion defect known as the piping defect (Fig.
Fig. 3.10 Formation of extrusion piping defect. 1, secondary deformation zone; 2, billet core; 3, shear zone; 4, primary deformation
zone; 5, shear zone; 6, dead metal zone; 7, extrusion
70 / Extrusion, Second Edition
3.10). It is necessary to reduce the billet length 3.1.1.4 Calculation of the Axial Loads in
and/or lengthen the discard thickness to prevent Direct Hot Extrusion without
this piping defect. Lubrication and Shell (Aluminum
The material flow in direct extrusion without Alloys)
lubrication can be summarized as:
Flow type S is purely theoretical and does Calculation of the Friction Load FR. As al-
not occur in practice. ready discussed, the stem load FSt can be as-
Flow type A assumes little friction between sumed to consist of the sum of the axial load FM
the billet and the container. These conditions acting on the die, which is necessary for the de-
rarely occur in unlubricated extrusion. They can formation of the material being worked in the
develop in the extrusion of, for example, lead or primary deformation zone, and the axial load FR
copper where special conditions, e.g., relatively required to overcome the friction between the
severe oxidation of the billet surface and a billet and the container. From Eq 3.4:
freshly cleaned container occur.
The two most important flow types for direct FSt 艑 FR Ⳮ FM
extrusion without lubrication and with flat dies
are types B and C, although the boundary be- From Fig. 3.5 the friction load FR can be cal-
tween the two is flexible. They occur in the ex- culated by assuming that there is shear stress sS
trusion of aluminum alloys and copper alloys with which the billet shears along the boundary
and are shown in principle in Fig. 3.11. surface. The maximum value of the shear load
FR max occurs after the billet has been upset in temperature and a specific speed. According to
the container where SSt ⳱ S1 at the start of the Eq 3.7:
actual extrusion process given by, according to
Eq 3.5: sS ⳱ f (material, temperature, shear rate)
Fig. 3.12 Variation of the shear stress with the shear rate for Al99.5 at different temperatures
72 / Extrusion, Second Edition
cated mandrel. The die diameter is only slightly ignoring the friction between the billet and the
larger than the mandrel diameter. Fixing the mandrel:
dummy block avoids the material flowing back
against the piercing ram movement during pierc- FD ⳱ ss • DDp(l0 ⳮ sD) (Eq 3.10)
ing.
The macrographs in Fig. 3.15 show that dur- where l0 is the upset billet length in the container
ing piercing, the narrow shear zone formed is and DD the mandrel diameter.
narrow enough to be designated a boundary sur- From Eq 10:
face. After piercing the core length must be
equal to the upset billet length. For a piercing FD
ss ⳱ (Eq 3.11)
load FD over the mandrel displacement SD and DDp(l0 ⳮ sD)
Fig. 3.13 Variation of the shear stress with temperature for shear rates between 2 and 6 mm/s for Al99.5
Fig. 3.14 Determination of the shear stress sS by piercing an upset billet. A, upsetting the billet; B, opening the die; C, piercing; a,
container; b, die; c, die holder; d, dummy block; e, stem; f, mandrel; g, sealing piece; h, billet; i, sealing plate
Chapter 3: Rod and Tube Extrusion Processes / 73
From the maximum piercing load FD max at the zone, a quasi-stationary deformation process is
start of piercing when SD ⳱ 0: referred to. The maximum in the axial load FM
occurs in the nonstationary state.
FD max For the quasi-stationary state:
ss ⳱ (Eq 3.12)
DDpl0
D20
FM ⳱ C • ugges • k¯ fp (Eq 3.13)
It is therefore possible to experimentally deter- 4
mine sS and show it in diagrams. In the deter-
mination of the shear stress sS, it is assumed that where k̄f is the mean flow stress for the primary
the mean stress state in the billet (usually re- deformation zone, ugges is the logarithmic total
ferred to as the hydrostatic stress) does not in- strain (Eq 3.14), and C is a factor that is die
fluence the shear stress. The validity of this as- specific and includes a shape efficiency factor g.
sumption still has to be scientifically verified. ugges is obtained from the extrusion ratio
Calculation of the Deformation Load FM. (Eq 3.1):
The following discussion covers the axial load
FM acting on the die necessary for the defor- A0
mation of the material located in the primary ugges ⳱ ln V ⳱ ln (Eq 3.14)
AS
deformation zone.
If the initial billet temperature is approxi- where A0 is the container cross-sectional area
mately the same as the container temperature, and AS is the section cross-sectional area. The
which is the case in the hot extrusion of alumi- flow stress kf is the stress at which plastic flow
num, then FM is approximately constant over the of a material occurs in a uniaxial stress state. The
stem displacement. There is only a maximum at flow stress kf is a function of the material, the
the start of extrusion, which is associated with deformation temperature, the logarithmic prin-
the temperature in the deformation zone at the cipal strain ug, and the logarithmic principal
start of extrusion being the initial billet tem- strain rate u̇g.
perature. A temperature increase occurs in the Flow Stress kf ⳱ f (material, , ug, u̇g).
deformation zone as extrusion continues be- The mean flow stress k̄f in Eq 3.13 can be
cause of the work of deformation. This results obtained from quasi-adiabatic flow curves found
in decreasing deformation loads as the flow in the literature for:
stress is reduced by the increasing temperature.
If approximately constant strain, velocity, and ● The temperature E that the material being
temperature conditions occur in the deformation deformed enters the deformation zone
74 / Extrusion, Second Edition
● The mean logarithmic principal strain ūg appears to better describe the velocity behavior
● The mean logarithmic principal strain rate in the deformation zone and will therefore be
u̇¯ g used to determine the mean flow stress for the
● The specific material primary deformation zone.
Figure 3.16 shows for Al99.5 in a double log-
ūg and u¯˙ g are mean values that apply to the entire
arithmic format the flow stress kf as a function
material being deformed in the deformation of the logarithmic principal strain ug.
zone.
This graph gives straight lines for kf ⳱ f (ug).
k̄f ⳱ f (material, entry temperature E, mean These have been extrapolated from ug ⳱ 1.1.
logarithmic principal strain ūg, mean logarith- The values in the range 0.4 ⱕ ug ⱕ 1.1 are taken
mic principal strain rate u̇¯ g). from the measured values from the work [Bue
From the literature [Sie 76a]
70]. These flow stress values are show for the
logarithmic principal strain rates u̇g ⳱ 0.25, 4.0,
3
ūg ⳱ 2ln (Eq 3.15) and 63 sⳮ1. It can be seen that as the temperature
DS increases, the influence of the logarithmic prin-
Ⳮ2
D0 cipal strain rate also increases.
Figure 3.17 shows for aluminum in double
Vⳮ1 logarithmic format the flow stress as a function
u̇¯ g ⳱ • uSt (Eq 3.16)
lU of the logarithmic principal strain rate.
These values were measured for the principal
where lU is the length of the deformation zone. strains ug ⳱ 1, 3, and 5 [Alu]. Figure 3.18
In the extrusion of round bars of diameter DS, shows that in the temperature range 350 to 500
then, for a conical deformation zone with an C, the influence of the logarithmic principal
opening angle 2␣ ⳱ 90: stress on the flow stress is small. Flow stress
values as a function of ug, u̇g, and for metallic
D0 ⳮ DS materials can be found in the literature, e.g.,
lU ⳱ (Eq 3.17) [DGM 78].
2 tan ␣
The factor C in Eq 3.13 contains:
If it is assumed for the hot extrusion of a round
bar the deformation zone is conical with ␣ ⳱ C⳱
fp
(Eq 3.21)
45, then from Eq 3.16 and 3.17: gF
冪
4 • AS The deformation efficiency factor gF is defined
S ⳱
D* (Eq 3.19)
p as the ratio of the theoretical deformation load
needed FM theor to the actual measured load
where AS is the section cross-sectional area. FM gem:
From the literature [Ake 66], [Stu 68], and
[Stu 71], the approximation for direct hot extru- pD20
k̄f • ugges •
sion attributable to Feltham [Fel 56] is: FM theor 4
gF ⳱ ⳱ (Eq 3.23)
FM measured FM measured
uSt
u̇¯ g ⳱ 6 • • ugges (Eq 3.20)
D0 If no experimental results are available, gF ⳱
0.5–0.6 can be assumed.
This approximation does, however, give signifi- If a round bar is being extruded, the factor C
cantly lower values than does Eq 3.18, which is given by:
Chapter 3: Rod and Tube Extrusion Processes / 75
Fig. 3.16 Flow stress kf of Al99.5 as a function of the logarithmic principal strain g for E ⳱ 20 C, 120 C, and 240 C (values
in the range 0.4 ⱕ ug ⱕ 1.1 taken from [Bue 70])
76 / Extrusion, Second Edition
Fig. 3.17 Flow stress kf of Al99.5 as a function of the logarithmic principal strain rate u̇g (values from [Alu])
the billet immediately before the start of extru- but it is possible for these to change during the
sion. period between heating and upsetting.
The temperature of the container is also an The variation in the billet temperature in the
important process parameter. axial and radial direction immediately before the
Whereas it is adequate to only input the mean upsetting of the billet is of interest.
initial temperature of the dummy block and the The temperature distribution in the container
die, an understanding of the temperature of the is more difficult to analyze.
billet and the container is needed in both the Figure 3.19 shows the axial temperature pro-
axial and the radial direction. file along the container wall in the static empty
It is possible with an induction billet furnace condition. This shows that the actual tempera-
to develop temperature gradients in the billet, ture A displayed at the control desk is exceeded
Fig. 3.18 Calculated variation of the stem load FSt over the stem displacement for Al99.5. The result is the principal variation of
the stem force over the stem displacement shown in the figure.
Fig. 3.19 Temperature variation in the axial direction at the container wall [Sie 76a]
78 / Extrusion, Second Edition
in the middle of the container, and the tempera- formation zone undergoing the full deformation
ture toward the end faces is significantly lower. ugges will have the exit temperature given by A
In the stationary empty condition the maximum where:
temperature occurs in the center of the container.
Figure 3.20 shows the change in the container A ⳱ E Ⳮ DU (Eq 3.27)
temperature fields for different extrusion inten-
sities. These show that as the intensity of the
extrusion operation increases, the temperature Here, E is the temperature of the material being
maximum moves toward the die, and with an extruded as it enters the deformation zone. It is
intense press operation, the temperature increase assumed that no heat flows back from the de-
comes entirely from the friction and deformation formation zone into the billet.
with the container heating switched off. It is also assumed that no heat flows from the
Considering the heat sources in extrusion the deformation zone into the container and die in
deformation work in the primary deformation contact with the deformation zone. The entry
zone is converted to heat. temperature E is determined from the model
Thus: assumption that the material being extruded con-
sists of flat parallel discs perpendicular to the
FM • s ⳱ QU (Eq 3.25)
center line between the deformation entry plane
and billet end. With the assumption of a bound-
ary surface within which the material being ex-
In a quasi-adiabatic process, this heat in the
truded shears as the billet moves through the
material being extruded produces a temperature
container, the thermal conditions in a disc can
increase of:
be considered as shown in Fig 3.21.
The disc has a thickness of 10 mm and a di-
k̄f • ugges
DU ⳱ (Eq 3.26) ameter D0. It is pushed through the container
q•c with a stem speed uSt. In the time t, the quantity
of heat Qs that develops in the boundary surface
where q is the density and c the specific heat of is:
the material being extruded. This relationship
first applies in the quasi-stationary extrusion t
process because at the point of upsetting, not all
the billet volume will pass through the defor-
Qs ⳱ (p • D0 • 10 mm) 冮0
sS • uSt • dt (Eq 3.28)
Fig. 3.20 Principal variation in the container temperature for different working conditions [Ake 71]
Chapter 3: Rod and Tube Extrusion Processes / 79
2 • bB • bR • (E ⳮ R)
Qk ⳱ (p • D0 • 10 mm) 冪t
冪p(bB Ⳮ bR)
(Eq 3.33)
DQ
DB ⳱ (Eq 3.35)
p 2
D • 10 mm • qB • cB
4 0
Fig. 3.22 Influence of the friction between the billet and container on the increase in temperature in the deformation zone and on
the exit temperature in direct extrusion without lubrication and without a shell for R ⳱ B
Chapter 3: Rod and Tube Extrusion Processes / 81
However, as a rule, the influence of the entry ● Optimization of the difference between the
temperature as a result of the shear friction dom- initial billet temperature and the container
inates so that the exit temperature increases with temperature
increasing stem displacement. Thus, the section ● Axial billet temperature profile (this requires
exit temperature S over the stem displacement an induction billet heating furnace)
SS or section length follows, in principle, the ● Stem speed as a function of stem displace-
profile shown in Fig. 3.22 for the direct hot ex- ment
trusion of aluminum alloys. ● Zone heating and zone cooling of the con-
Figure 3.23 shows the measured section exit tainer with the aim of maintaining the tem-
temperature for the aluminum alloy perature fields in the container largely inde-
AlZnMgCu0.5 over the section length. This pendent of the extrusion process
temperature was measured with a micromantle
thermocouple Th in the die land. Figure 3.23 If the material being extruded enters the de-
also shows the maximum possible exit tempera- formation zone with a constant exit temperature
ture without the occurrence of section transverse E then, as shown in Fig 3.24, the section exit
cracks (hot cracking). temperature is constant over the extrusion length
The aim for an economic extrusion process is
after an unsteady upset process. The product
to use the maximum ram speed possible. How-
properties are then constant over the length of
ever, specific material-related limiting tempera-
the extrusion.
tures should not be exceeded to avoid hot crack-
ing. The structure and thus the product
properties can also change with the section exit
temperature S. 3.1.2 Direct Hot Extrusion without
For high productivity in extrusion, the stem Lubrication and with a Shell
speed over the stem displacement should be as (Copper Alloys)
high as possible.
Copper alloys are usually extruded by direct
The exit temperature E should be as constant
or by indirect hot extrusion without lubrication
as possible over the product length to ensure a
and with a shell. Both processes will be dis-
defect-free product. Specific limiting tempera-
cussed to enable a direct comparison to be made
tures at which transverse cracks can occur
should never be exceeded. between them for the extrusion of copper alloys.
The following possibilities exist to obtain an Thus, The extrusion of copper alloys is usu-
exit temperature as constant as possible. These ally carried out without lubrication and with a
are usually not used individually but together: shell by the direct or indirect hot extrusion pro-
cess.
In direct hot extrusion without lubrication and
with a shell the contaminated and oxidized pe-
ripheral zone of the upset billet in the container
is sheared to leave a tubular shell on the con-
tainer wall. The thickness of the shell is deter-
mined by the gap between the container and the
dummy block. The shell ensures that only
defect-free material enters the extrusion. The
disadvantage is that the shell has to be removed
from the container.
card length is reached. A shell that adheres to card, shell, dummy block, and discard into the
the container wall is formed between the dummy discard tool.
block and the container wall. At the end of the The stem is then withdrawn to the starting po-
extrusion process the stem is withdrawn. The sition. The container then travels back far
container is then opened far enough to allow the enough to enable the discard tool to be swung
section to be sawn and a discard tool to be out. The container then returns to its starting po-
loaded between the die and the container. The sition.
stem then scalps the shell from the container With some extruded alloys there is the option
wall using a cleaning disc and pushes the dis- of using a combination block (Fig. 3.46). This
Fig. 3.24 Constant entry temperature E as the requirement for a constant exit temperature over the length of the extrusion or over
the stem displacement in direct extrusion without lubrication and without a shell (billet temperature increasing toward
the front of the billet and ram speed decreasing over the stem displacement as well as in some cases zone heating and cooling of the
container)
Fig. 3.25 Process sequence in direct hot extrusion without lubrication and with a shell of copper alloys. a, platen; b, die holder;
c, die; d, container; e, billet; f, dummy block; g, extrusion stem; h, cleaning billet; i, discard tube; k, shell; l, discard
84 / Extrusion, Second Edition
process uses a combination of the dummy block As the stem displacement increases the billet
and the cleaning disc with an intermediate cham- volume enters the deformation zone with a de-
ber into which the shell is compressed. It is then creasing entry temperature E. As the entry tem-
possible with this combination block to elimi- perature E decreases, the flow stress kf rises and
nate the process sequence shown in Fig. 3.25 of the deformation load FU increases with stem dis-
withdrawal of the stem, loading of the cleaning placement. Figure 3.26 shows the variation in
block, and cleaning by moving the stem for- the stem load FSt over the stem displacement s
ward. as the sum of the deformation load FU and shear
or friction load FR. The deformation load FU is
equal to the axial load acting on the die FM (FU
3.1.2.2 Variation in the Stem Load over ⳱ FM).
the Stem Displacement in Direct
Hot Extrusion without Lubrication 3.1.2.3 Material Flow in Direct Hot
and with a Shell Extrusion without Lubrication and
In principle, the stem load variation over the with a Shell
stem displacement in direct hot extrusion with- Figure 3.27 shows stages in the direct hot ex-
out lubrication and with a shell should be the trusion without lubrication and with a shell for
same as in direct extrusion without lubrication CuCo2Be. As the stem moves forward (decreas-
and without a shell. In direct hot extrusion with- ing billet length), the friction between the billet
out lubrication and without a shell, e.g., alumi- and the container results in an extremely severe
num, a film of the material being extruded coats distortion of the grid lines. The hotter internal
the container wall and shearing of the material zones accelerate forward, and the peripheral
being extruded has to take place similar to ex- zone restrained by the friction between the ma-
trusion with a shell. terial being formed and the container wall flows
In the extrusion of copper alloys, the initial in as a secondary deformation zone at the back
billet temperature B is usually higher than the of the billet (compare with Fig. 3.9 and 3.11 and
container temperature R. Heat then flows from the discussion in section 3.1.1.3). The material
the billet into the container. This is usually larger flow in direct hot extrusion without lubrication
than the heat transfer into the billet from the and with a shell can be classified as flow pattern
shearing of the shell. C in Fig. 3.11.
Fig. 3.26 Principal variation of the stem load FSt and the deformation load FU ⳱ FM over the stem length sSt for the direct hot
extrusion with a shell for the initial billet temperature B that is significantly above the container temperature R, which
is the case for direct hot extrusion with a shell of copper alloys
Chapter 3: Rod and Tube Extrusion Processes / 85
3.1.2.4 Calculation of the Axial Forces in s̄S can then be obtained for ¯ Ba taking into ac-
Direct Hot Extrusion without count the stem speed (shear rate) providing shear
Lubrication and with a Shell flow curves are available.
Allowance should also be made for the de-
The calculation of the axial forces for direct crease over the stem displacement of the entry
hot extrusion without lubrication and with a temperature E of the material being deformed
shell can, in principle, follow the procedure de- into the deformation zone. The flow stress kf will
scribed in section 3.1.1.4. One factor to take into then increase over the stem displacement. The
account is that in the determination of the shear calculation of the entry temperature can be car-
load (friction load) over the stem displacement ried out following the method of Lange [Lan 71]
FR ⳱ f (sSt), the shear stress sS is obtained for in section 3.1.1.4.
the temperature in the billet peripheral zone. The
temperature of the material being deformed in 3.1.2.5 Thermal Conditions in Direct Hot
the billet peripheral zone will decrease with in- Extrusion without Lubrication and
creasing billet/container contact time despite with a Shell
transfer of the heat from the shearing. The time
of contact can be obtained from the stem speed Copper alloys are extruded at working tem-
and the upset billet length. The mean tempera- peratures over 600 C. Typical initial billet tem-
ture in the billet peripheral zone can be roughly peratures for copper alloys fall in the range 600
estimated to be: to 800 C. However, the thermal resistance of
hot-working steel extrusion tools has a maxi-
¯ Ba ⳱ B Ⳮ R
mum temperature of 500 C. The tool tempera-
(Eq 3.38) ture should therefore be below this value. Some
2
heat therefore will flow from the billet into the
where B is the initial billet temperature and R container. This heat loss is higher than the heat
the container temperature. A mean shear stress gain from shearing the shell.
Fig. 3.27 Stages in the direct hot extrusion with a shell of the alloy CuCo2Be (Source: K. Müller, Srangprebzentrum Berlin)
86 / Extrusion, Second Edition
The billet cross-section discs thus enter the billet temperature B and the container tempera-
deformation zone with a temperature that de- ture R and the associated heat conduction into
creases with stem displacement. This results the container (Fig. 3.28).
over the stem displacement in an increasing tem- The temperature decrease predominates so
perature rise DU in the material being deformed that the exit temperature S decreases over the
as it passes through the deformation zone length of the extrusion.
throughout the stem displacement. As a general rule, the cooling of the extrusion
It is a fact, however, that the temperature E billet in the container and the risk of piping de-
decreases with stem displacement in spite of the fect (see section 3.1.1.3) limits the billet length
heat input from the shearing of the shell because in the direct hot extrusion with a shell of copper
of the temperature difference between the initial alloys to:
Fig. 3.28 Principal temperature variation over the stem displacement or over the extruded length in direct hot extrusion without
lubrication with a shell for the initial billet temperature B that is significantly above the container temperature R, which
is the case for the direct hot extrusion with a shell of copper alloys
Chapter 3: Rod and Tube Extrusion Processes / 87
Fig. 3.29 Process sequence in extrusion of steel solid sections. See [Lau 76]. a, platen; b, die holder; c, die; d, container; e, billet;
f, dummy block; g, extrusion stem; h, saw; i, discard tool
88 / Extrusion, Second Edition
the billet is loaded together with a glass lubricant as is the case in the extrusion of steel, then there
disc in the front and a loose dummy block at the is a significant heat loss from the billet to the
back between the container and the stem and container even with relatively short contact
then loaded into the container. After the billet times. The friction between the billet and the
has been upset in the container, during which the container in direct hot extrusion with lubrication
glass reaches a low viscosity and surrounds the and without a shell is extremely low. The heat
entire billet with lubricant, extrusion continues transfer into the billet from the friction billet/
to the preset discard length. The container is then container is comparatively negligible compared
opened so that the section can be sawn from the with the heat flow from the billet into the con-
discard. tainer.
When necessary, the container travels forward As shown in Fig. 3.30 the deformation load
to push the section from the die using the resid- FU increases over the stem displacement because
ual section on the discard. the billet zones enter the deformation zone with
Finally, the container travels back to enable a a continuously decreasing temperature and thus
discard tool to be moved between the container increasing flow stress as the stem displacement
and the end housing. The stem then pushes the increases. The difference between the stem load
discard with the dummy block into the discard and the deformation load is equal to the friction
tool. load FR, which is necessary to overcome the
So far the discussion has concentrated on the friction between the billet and the container. The
pure process sequence. Special features to con- friction between the billet and the container can
sider include: be assumed to be Coulombic friction (see sec-
● The container seal against the die is conical. tion 3.1.4.2).
● The die is conical so that no dead metals
zones form. 3.1.3.3 Material Flow in Direct Hot
● The high billet temperature of over 1000 C Extrusion with Lubrication
requires a short contact temperature taking
into account the tool temperature of approx- In direct hot extrusion with lubrication, the
imately 800 C. This necessitates high stem deformation zone that develops in the material
speeds. Nevertheless, the service life of the flow through conical dies is virtually enclosed
die is so low that sometimes a new or re- by the die cone. With large die opening angles
worked die has to be used after each extru- it curves into the billet.
sion. The lubrication reduces the friction between
● In addition to the material being extruded, the billet and the container to such an extent that
the service life of the die depends on the ex- it can approximately be assumed that the friction
trusion ratio and the section exit speed as has no influence on the material flow. As shown
well as the die shape and the lubricant used.
This should, on one hand, have sufficient lu-
brication properties to completely separate the
material being extruded from the container wall
and the die and, on the other hand, the lubricant
should also have a low thermal conductivity—
in other words, provide thermal isolation. Glass
and combinations of grease, oil, and graphite are
used as lubricants. Glass provides very good lu-
brication and simultaneously excellent insula-
tion. Direct hot extrusion of steel is, therefore,
usually lubricated with glass.
in Fig. 3.31, a deformation zone forms that ex- increase DU, therefore, increases over the stem
tends slightly from the die cone into the billet. displacement or the section length.
With this type of material flow, the surface of The influence of the entry temperature E
the extrusion is formed from the billet peripheral over the stem displacement or section length is
zones. They should as far as possible not be ox- the dominating factor on the section exit tem-
idized. perature S, which decreases over the stem dis-
placement or the section length. See the tem-
3.1.3.4 Thermal Conditions in Direct Hot perature profiles in Fig. 3.32.
Extrusion with Lubrication
3.1.4 Direct Cold Extrusion with
In the consideration of thermal conditions, at- Lubrication and without a Shell
tention has to be given to the fact that the billets
in the extrusion of steel have temperatures be- As in all direct extrusion processes, friction
tween 1100 and 1200 C, whereas the container between the container wall and the billet has to
temperature usually cannot exceed 700 C. be taken into account in direct cold extrusion
There is, therefore, a large temperature differ- with lubrication and without a shell. This fric-
ence, which makes it necessary to have the tion is minimized by using a lubricant that is
shortest possible contact time between the billet normally applied to the billet before extrusion.
and the container and consequently for the ex- Conical dies are usually used to ensure that the
trusion process. lubricant surrounds the material being extruded
The mechanical presses used earlier have up to the exit from the die. The billet is also
been largely replaced in recent years because tapered at the front.
they have proved to be uneconomic for the pro- Direct cold extrusion with lubrication and
duction of low-alloy steel tubes compared with without a shell is characterized by the friction
tube rolling processes (see the section “Extru- between the material being extruded and both
sion of Iron-Alloy Semifinished Products” in the container and the die. This friction is mini-
Chapter 5). mized by the use of a lubricant.
Today, horizontal hydraulic presses with ac-
cumulator drive are almost exclusively used be- 3.1.4.1 Process Sequence in Direct Cold
cause the accumulator drive provides high stem Extrusion with Lubrication and
speeds. without a Shell
Over the stem displacement sSt or the section
Figure 3.33 shows a possible process se-
length lS ⳱ V • sSt billet zones enter the defor-
quence. The dummy block is fixed to the stem.
mation zone with a decreasing temperature (E),
The billet tapered at the front is coated with lu-
where there is a temperature increase DU as-
bricant and loaded into the container. It is then
sociated with the deformation. The flow stress kf
extruded to a preset discard length. The con-
increases with the decreasing temperature of the
tainer and stem are then withdrawn to enable the
material being deformed, and the temperature
discard to be pulled from the die with a manip-
ulator and the section to be cut free with a saw.
The discard is then removed from the press
with the manipulator and the section pulled from
the die. The container and stem finally travel
back to the corresponding starting position.
process after an unsteady initial process, which metrically restrained by the die wall, the die en-
is characterized by the maximum value F̂M and try plane, and the die exit plane (Fig. 3.35).
F̂St, whereas the friction load FR falls exponen- The axial force PEid for the ideal deformation
tially over the stem displacement. in the entry plane is given using the logarithmic
The stem load FSt is obtained from the sum total principal strain ugges (see Eq 3.14) or the
of the deformation load FU and the friction extrusion ration V by:
load FR. pXEid ⳱ k¯ f • ugges ⳱ k¯ f • ln V (Eq 3.40)
In direct cold extrusion with lubrication and
without a shell, the starting point is the model where k̄f is the mean flow stress for the total
assumption that the deformation zone is geo- volume in the deformation zone. The mean log-
Fig. 3.32 Principal variation in the exit temperature S for direct hot extrusion with lubrication and without a shell for the initial
billet temperature B that is much higher than the container temperature R (e.g., the direct hot extrusion with lubrication
and without a shell of steel)
Chapter 3: Rod and Tube Extrusion Processes / 91
arithmic principal strain ūg at the volume center From this, according to Eq 3.15:
of gravity S is needed to determine this from the
quasi-adiabatic flow curves. The volume centre 3
ūg ⳱ 2 ln
of gravity of the deformation zone is approxi- DS
mately given by: Ⳮ2
D0
Fig. 3.33 Process sequence in direct cold extrusion with lubrication and without a shell. a, platen; b, die holder; c, die; d, container;
e, billet; f, stem with fixed dummy block; g, manipulator; h, saw
92 / Extrusion, Second Edition
2
2冤冢 冣
D0
DS
ⳮ1 冥 In the extrusion of low-melting-point materi-
als, e.g., lead and tin, the mean logarithmic strain
u̇¯ g ⳱ • uSt rate has to be taken into account.
D0 ⳮ DS
The ideal axial compressive stress PXEid re-
quired for perfect deformation on the die entry
In the cold working of metallic materials, the plane multiplied by a factor C gives the actual
melting point of which is well above room tem- axial compressive stress:
perature, it is usually possible to ignore the in-
fluence of the logarithmic strain rate on the flow Px ⳱ C • PXEid (Eq 3.41)
stress. It is, therefore, possible to obtain the flow
stress k̄f for copper and aluminum alloys from here, the factor C from Eq 3.21 contains a profile
adiabatic flow curves for E ⳱ 20 C and ūg factor fp and a deformation efficiency factor (see
using Eq 3.15. section 3.1.1.4).
Fig. 3.34 Principal variation in the axial force FM, FR, and FSt over the stem displacement for direct cold extrusion with lubrication
and without a shell
Chapter 3: Rod and Tube Extrusion Processes / 93
pX ⳱ pXE • e4(l0/D0)x̄
Ⳮ kf0 • [1 ⳮ e4(l0/D0)x̄] (Eq 3.45)
from Eq 3.40, taking Eq 3.14 and 3.1 into ac- The flow stress kf0 is the initial flow stress ex-
count: hibited in the billet when it is loaded in the press.
It can approximately be set as equal to the proof
pXE ⳱ C • pXEid ⳱ 1.1 • k¯ f • ugges stress of the billet material.
⳱ 1.1 • k¯ f • lnV (Eq 3.43) Then:
This force reduces during extrusion to a mini- The temperature increase in the deformation
mum value: zone has to be taken into account. The work
needed for the deformation is almost 100% con-
p • D20 verted into heat. Thus, for the section exit tem-
FSt(x̄ ⳱ 0) ⳱ • pXE ⳱ FU (Eq 3.50)
4 perature St under adiabatic conditions:
Fig. 3.36 Principal representation of the variation of the axial compressive stress px and the radial compressive stress pr in direct
cold extrusion with lubrication without a shell. l0, upset billet length; sSt, stem displacement; D0, container diam; DS,
extrusion diam; lU, length of the deformation zone
Chapter 3: Rod and Tube Extrusion Processes / 95
The higher the strain, the higher is the section 3.2 Indirect Extrusion
exit temperature E. It can be several hundred
degrees Celsius in cold extrusion. The principle of the indirect extrusion process
Example (see Fig. 3.37): has been known since 1870 and was used com-
Material Al99.5 mercially in 1930 for the extrusion of brass
Container diam DO ⳱ 85 mm semifinished products. The breakthrough in in-
Initial billet diam DB ⳱ 82.5 mm
Initial billet length lB ⳱ 450 mm Ⳮ tip
direct extrusion, however, first occurred around
Product Round/12.02 mm 1960 with the extrusion of brass wire and sec-
Initial billet temperature ⳱ container 20 C tions in high-strength aluminum and copper al-
temperature
loys. Figure 3.1(b) shows the basic indirect ex-
Equation Parameter Result trusion process.
(3.1) V ⳱ 50 Extrusion ratio The indirect extrusion process can be classi-
(3.14) Logarithmic total principal strain ugges ⳱ 3.9
(3.15) Mean log. Principal strain ūg ⳱ 0.674
fied into hot indirect extrusion or cold indirect
extrusion, depending on whether the billet is
With ūg ⳱ 0.674 and E ⳱ 20 C, then from loaded into the container heated or cold, i.e., at
Fig. 3.16: room temperature:
k̄f ⳱ 160 N/mm2
● Hot indirect extrusion: A heated billet is
Equation Parameter Result loaded into the container.
(3.40) Ideal axial compressive pXEid ⳱ 626 N/mm 2
Fig. 3.37 Calculated variation of the stem load over the stem displacement in direct cold extrusion of aluminum with lubrication
and without a shell. D0 ⳱ 85 mm; V ⳱ 50; lB ⳱ 450 mm Ⳮ tip; l ⳱ 0.02; ReH ⳱ 120 N/mm2
96 / Extrusion, Second Edition
during extrusion. No shell is produced between the billet is loaded, this will finish in the discard
the external die wall and the container wall. and not in the extrusion.
Hot Indirect Extrusion without Lubrica- The operating sequence in indirect extrusion
tion and with a Shell. No lubricant is used dur- with a loose die in front of the hollow stem is
ing extrusion. A shell is produced almost as a shown in Fig. 3.38. It can be seen that a short
second extruded product between the external sealing stem seals the container and pushes this
die wall and the container wall. over the die and hollow stem. After loading the
The cold indirect extrusion process can be di- billet is upset in the container and then extruded.
vided into extrusion with lubrication and extru- The extrusion load is then transferred through
sion without lubrication. In extrusion with lu- the sealing stem. The discard can be sheared by
brication the upset billet in the container is a shear located on the container.
surrounded by a lubricant film. This lubricant As well as using a loose die it is also possible,
film flows during extrusion both in the contact as shown in Fig. 3.39, to screw the die directly
zone between the die wall and the billet as well to the hollow stem or to locate it together with
as in the contact zone between the die external a die backer in a die holder attached to the hol-
wall and the container wall. No shell is produced low stem by a bayonet connection.
in either process. Figure 3.40 shows an example of a hollow
Cold Indirect Extrusion without Lubrica- stem with a screwed-on hollow stem extension
tion and without a Shell. No lubricant is used fitted with a bayonet connection. The die holder
during extrusion. is fitted to the latter by the bayonet connection.
Cold Indirect Extrusion with Lubrication A rigid connection between the die or the die
and without a Shell. A lubricant is used to re- holder and the hollow stem results in withdrawal
duce the friction between the die and the billet loads and therefore places stresses on the thread
and to reduce the friction between the die exter- or bayonet connection (Fig. 3.39). There is also
nal wall and the container wall. the risk that billet material is shaved from the
container wall by the rear edge of the die during
the return stroke. This has to be removed before
3.2.1 Hot Indirect Extrusion without the next cycle.
Lubrication and without a Shell It is also possible to extrude with a loose die
(e.g., Aluminum Alloys) guide ring (Fig. 3.39d). This does, however,
As shown in Fig. 3.38, in hot indirect extru- have to be changed after each extrusion. There
sion without a shell (and without a lubricant) the is no shaving of the billet material on the return
material being deformed is loaded as a billet be- stroke with this method of operation and no
tween the hollow stem and the container and high-return loads.
pushed along with the die into the latter by mov- The design of the sealing stem is very impor-
ing the container. tant in indirect extrusion.
As shown in figure Fig. 3.41, this can include
The billet can also be loaded between the con-
a chamber. The material being extruded then
tainer and the sealing stem. This does, however,
flows into the container when the billet is upset
have the disadvantage that when the billet slides
in the container.
into the container, pieces of the material being The friction between the material being ex-
extruded adhering to the container wall can be truded and the chamber wall enables the discard
shaved off by the billet and pushed in the direc- to be torn away or pulled away from the die at
tion of the billet. This can then flow into the the end of the actual extrusion process as shown
extruded product during extrusion, resulting in in Fig. 3.41. The removal of the discard with a
extrusion defects. “loose die guide ring” is shown in Fig. 3.42.
This is avoided if the billet is loaded between The following methods of die guiding can be
the hollow stem and the container. In this case, used in indirect extrusion:
any shavings of the material being extruded Loose Die Guiding. The loose die is loaded
from the container wall are pushed in the direc- in front of the hollow stem and pushed out after
tion of the sealing stem and remain in the dis- shearing at the end of extrusion (Fig. 3.39). It is
card. also possible to saw between the hollow stem
In indirect extrusion the billet should prefer- and the discard after pulling back the discard
ably be loaded between the hollow stem and the together with the extrusion with a special cham-
container so that if any of the material being ber design in the sealing stem. The pull-out load
extruded is shaved from the container wall as comes from the friction between the deformed
Chapter 3: Rod and Tube Extrusion Processes / 97
material in the chamber of the sealing stem and Die Rigidly Attached to the Hollow Stem.
the chamber wall. The loose die is then removed In this case there are two possibilities. On one
along with the discard by a pusher located in the hand, the die can be screwed to the hollow stem.
sealing stem (Fig. 3.41, 3.42). On the other hand, it is possible to attach a die
Fig. 3.38 Process sequence in indirect hot extrusion without a shell. a, press platen; b, hollow stem holder; c, hollow stem; d, die;
e, billet; f, container; g, sealing stem. See [Bis 73].
98 / Extrusion, Second Edition
holder to the hollow stem with a bayonet con- gether with the die closure ring (Fig. 3.39d,
nection (Fig. 3.39, 3.40). 3.42).
Die Rigidly Attached to the Hollow Stem
with a Loose Die Guide Ring. This arrange- 3.2.2 Hot Indirect Extrusion without
ment enables the discard to be separated with a Lubrication and with a Shell
saw because it is possible with the special design In hot indirect extrusion with a shell the latter
of the sealing stem to pull out the discard to- forms as a quasi-second (tube-shaped) extruded
Fig. 3.39 Die guiding in indirect extrusion. See [Zie 7]. (a) Loose die in front of the hollow stem. (b) Die rigidly screwed to the
hollow stem. (c) Die holder attached to the hollow stem by a bayonet connection. (d) Die rigidly attached to the hollow
stem with a loose die guiding ring
Fig. 3.40 (a) Hollow stem with internal thread. (b) Hollow stem with screwed-on extension with bayonet adapter. (c) Hollow stem
with screwed-on extension and die holder attached by bayonet connector
Chapter 3: Rod and Tube Extrusion Processes / 99
product between the die guiding land and the impure or peripheral zones can be extruded as
container wall. The gap between the die and the these peripheral zones remain in the shell. The
container and the length lMa of the die land are disadvantage is that this process needs a special
set so that a perfectly complete shell is formed operating sequence “shell removal.” Figure 3.45
around the circumference and over the extrusion shows the cycle.
stroke and remains bonded to the container wall It can be seen that the shell together with the
(Fig. 3.43). die are pushed into a discard collector loaded
The compressive stress state in the billet in between the container and the sealing stem dur-
front of the die has a significant influence on the ing the cleaning cycle.
selection of the gap and the length of the die One possibility for indirect extrusion with a
guide land. The higher the extrusion ratio, the shell but without a special cleaning cycle is to
larger is the gap. This means that the gap should use a so-called combination die (Fig. 3.46). The
be increased for low extrusion ratios, as shown shell is compressed into a space behind the die
in Fig. 3.44. guiding land. These combination dies have been
Hot indirect extrusion without lubrication and used successfully in the indirect extrusion of
with a shell has the advantage that billets with brass.
Fig. 3.41 Sealing stem with recess for withdrawal of discard and die
100 / Extrusion, Second Edition
3.2.3 Material Flow in Indirect Hot only by the thermal conditions and the buckling
Extrusion length of the hollow stem.
The die and the deformation zone formed in
As described in the section on direct hot-ex- front of the die are pushed through the container
trusion, the material flow can be studied by vi- during indirect hot extrusion. It should be noted
sio-plasticity (see section 3.1.1.3). that the billet in front of the die face does not
Figure 3.47 shows stages in the hot indirect flow toward the die opening but forms a so-
extrusion without lubrication or shell of called dead metal zone. The material flow can,
CuZn42. The distortion of the grid shows that a therefore, not be described by the flow type S
small deformation zone forms directly in front (see Fig. 3.11). This has been claimed in the past
of the die face. The billet volume adjacent to the by some authors but has since been clearly seen
deformation zone is completely unaffected by to be incorrect. Figure 3.48 shows a section of
the extrusion process. The material flow is, an AlMg3 billet extruded indirectly without lu-
therefore, not affected by the billet length. From brication. The material flow is the same as
the material flow point of view there is no limit shown in Fig. 3.47 for brass. This principal ma-
on the billet length. The billet length is limited terial flow also occurs—as shown in Fig. 3.44—
Fig. 3.42 Sealing stem with recess for withdrawal of discard and loose guide ring
Chapter 3: Rod and Tube Extrusion Processes / 101
Fig. 3.44 Material flow in indirect extrusion with a shell (a) V ⳱ 70 and (b) V ⳱ 30. AlMg3, container diam ⳱ 140 mm, container
temperature ⳱ billet temperature ⳱ 450 C [Sie 76a], [Zie 73]
102 / Extrusion, Second Edition
Fig. 3.45 Process sequence for the indirect extrusion without lubrication and with a shell. a, platen; b, hollow stem holder; c,
hollow stem; d, die; e, billet; f, container; g, sealing stem; h, cleaning block; i, shell; j, discard tool. See [Bis 75].
Chapter 3: Rod and Tube Extrusion Processes / 103
Fig. 3.46 Combination of die and cleaning block [Pet 59, Zie 77]
Fig. 3.47 Material flow (extrusion stages) in indirect hot extrusion without a shell and without lubrication of CuZn42 billets with
container diam D0 ⳱ 110 mm
104 / Extrusion, Second Edition
for indirect hot extrusion without lubrication and 3.2.4 Axial Forces and Extrusion Exit
with a shell. In this case there is a quasi second Temperatures in the Indirect Hot
die aperture between the die external guiding Extrusion with an Initial Billet
surface and the container. The aim is for the shell Temperature Equal to the Container
to adhere to the container wall and is thus no
Temperature (e.g., Aluminum Alloy
longer than the upset billet length less the dis-
card length. Extrusion)
In principle, the material flow for the indirect The characteristic feature of all indirect extru-
hot extrusion without shell can be described as sion processes is that there is no friction between
shown in Fig. 3.48. Figures 3.47 and 3.48 show the billet and the container. It is, therefore not
how the billet external zone flows in indirect ex- possible—as is the case with direct extrusion—
trusion without a shell via the deformation zone to influence the material flow by the friction be-
into the external zones of the extrusion. tween the billet and the container.
To avoid this, extrusion can be carried out It should also be taken into account that, in
with a shell. In indirect hot extrusion the billet contrast to direct extrusion, no axial force is
material flows in the gap between the external needed to overcome the friction between the bil-
die surface and the container and forms a cylin- let and the container because it is the die, and
drical shell almost as a second extruded product not the billet, that is pushed through the con-
given the correct selection of the length of the tainer.
external die surface and the gap width. This shell If the container displacement load and the
should, as far as possible, adhere to the container load needed to overcome the friction between
wall during extrusion; i.e., at the end of extru- the container external land and the container is
sion, the shell is no longer than the die move- neglected, then the sealing stem load is equal to
ment within the container. the hollow stem load.
Figure 3.44 shows that if the mean compres- In indirect extrusion, the sealing stem load
sive stress in the billet is low, which is the case FVSt is approximately equal to the hollow stem
with small extrusion ratios, the shell has to be load FHSt, which is equal to the axial load on the
thicker. Figure 3.49 shows aluminum shells that die FM, if the friction between the die and the
have been pushed from the container. container is ignored. This load is equal to the
Fig. 3.48 Material flow in indirect hot extrusion without a shell and without lubrication. (a) Material AlMg3; extrusion ratio Vges
⳱ 50; initial billet length lb ⳱ 500 mm; container diam D0 ⳱ 140 mm. (b) Principal depiction of billet zones in indirect
extrusion without lubrication and without a shell [Sie 80]
Chapter 3: Rod and Tube Extrusion Processes / 105
axial load FU needed for deformation in the en- where q is the density and c the specific heat of
try plane of the deformation zone during the the billet material.
quasi-stationary extrusion process: According to Eq 3.27, the extrusion exit tem-
perature S is given by:
F¯ VSt ⳱ F¯ HSt ⳱ F¯ M ⳱ F¯ U (Eq 3.52)
S ⳱ E Ⳮ DU
For the unsteady start of the extrusion process:
Fig. 3.49 Removed aluminum shell in indirect hot extrusion with a shell and without lubrication. (a) Upset in the container on
removal. (b) Partly upset [Zie 73]
106 / Extrusion, Second Edition
If the initial billet temperature B is equal to The axial load F̄M is as with direct hot-extrusion
the container temperature R, then in indirect according to Eq 3.13 and 3.14:
extrusion with a constant sealing stem speed the
initial billet length is, according to the above, p • D20
F̄M ⳱ C • uggesk¯ f •
limited only by the buckling length of the hollow 4
stem. p • D20
As a general guide: ⳱ C • lnV • k¯ f •
4
Fig. 3.50 Variation in the exit temperature S over the length of the extrusion lS in indirect hot extrusion for E ⳱ B ⳱ R ⳱
constant (e.g., for aluminum)
Fig. 3.51 Variation of the sealing stem force FVSt over the sealing stem displacement sVSt in indirect hot extrusion with an initial
billet temperature equal to the container temperature
Chapter 3: Rod and Tube Extrusion Processes / 107
the sealing stem displacement apart from a load perature are held constant, then it is possible to
peak at the beginning, if the initial billet tem- use a press with a lower maximum load com-
perature is equal to the container temperature. pared with hot direct extrusion.
Compared with direct hot extrusion, the load Example:
profile is reduced by the friction load FR. In ad-
dition, the initial billet length in indirect hot ex- Material Al99.5
trusion can be up to seven times the container Container diam D0 ⳱ 140 mm
Initial billet diam DB ⳱ 136 mm
length. This is significantly longer than the ini- Initial billet length lB ⳱ 840 mm
tial billet length in direct hot extrusion, which is Product Round bar 19.8 mm
usually less than four times the container di- Initial billet temperature ⳱ container 400 C
temperature
ameter. The discard length in indirect hot extru- Ram speed 10 mm/s
sion is significantly smaller than in direct hot
extrusion (see Eq 3.3 and 3.55). Then,
The sealing stem load FVSt in indirect extru-
sion is lower than the stem load in direct extru-
Equation Parameter Result
sion by the friction load FR from the friction 3.1 Extrusion ratio V ⳱ 50
between the billet and the container. 3.14 Logarithmic total principal strain ugges ⳱ 3.9
At the same maximum press load, indirect ex- 3.15 Mean log Principal strain ūgges ⳱ 0.674
3.16 Mean log Principal strain rate u̇¯ g ⳱ 8.15 sⳮ1
trusion offers the following advantages over di-
rect extrusion under the condition that the initial
billet temperature is the same as the container: With u̇¯ g ⳱ 8.15 sⳮ1, ūg ⳱ 0.674 and ⳱
400 C, then the mean flow stress over the full
● For the same product cross section and the deformation zone from Fig. 3.17 is:
same initial billet temperature, the container
diameter can be increased; i.e., a higher ex- k̄f ⳱ 31 N/mm2
trusion ratio can be selected.
● For the same product cross section and the
Equation Parameter Result
same container diameter, the initial billet 3.21 Factor C for fp ⳱ 1 and gf ⳱ 0.6 C ⳱ 1.67
temperature can be reduced, which enables (estimated)
3.13 Deformation load FM ⳱ 3100 kN
the maximum possible extrusion speed to be 3.8 Upset displacement s1 ⳱ 47 mm
increased for aluminum alloys. 3.8 Upset billet length l0 ⳱ 793 mm
3.3 Discard length lR ⳱ 14 mm
If the container temperature, product cross 3.53 Maximum axial force at the start of F̂VSt ⳱ 3400kN
section, extrusion speed, and initial billet tem- the extrusion
Fig. 3.52 Calculated variation in the sealing stem force FVSt over the sealing stem displacement sVSt for Al99.5 in indirect hot
extrusion with an initial billet temperature equal to the container temperature. This gives the variation of the sealing stem
force over the sealing stem displacement shown in the figure.
108 / Extrusion, Second Edition
3.2.5 Axial Loads and Exit Temperatures the deformation zone with a decreasing entry
in Indirect Hot Extrusion with an temperature. If the entry temperature decreases,
Initial Billet Temperature Higher then the flow stress increases, and this also re-
than the Container Temperature sults in a larger temperature rise in the defor-
mation zone. In spite of this, the exit temperature
(e.g., in the Extrusion of Copper
falls over the sealing stem displacement and
Alloys) over the length of the section because the influ-
High productivity is achieved with the indi- ence of the decreasing entry temperature over
rect extrusion of copper alloys. In contrast to the the sealing stem displacement predominates.
previous discussions where the initial billet tem- Figure 3.53 shows the changes in the inlet tem-
perature was taken to be equal to the container perature S, the temperature increase in the de-
temperature, with copper alloys, the initial billet formation zone DU, and the extrusion exit tem-
temperature is over 600 C. The container tem- perature E over the length of the section lS,
perature cannot be raised above 500 C. The bil- which is the product of the sealing stem dis-
let, therefore, loses heat to the container so that placement sVSt and the extrusion ratio V. These
as extrusion continues the billet volume enters changes occur when the initial billet temperature
Fig. 3.53 Temperature variation over the sealing stem displacement or the length of the extrusion in indirect hot extrusion with an
initial billet temperature B that is higher than the container temperature R (e.g., for copper alloys)
Chapter 3: Rod and Tube Extrusion Processes / 109
B is higher than the container temperature R, reduce the initial billet temperature and/or
which is usually the case for the indirect extru- increase the container diameter, i.e., increase
sion of copper alloys. the extrusion ratio with a significantly larger
The sealing stem load increases over the seal- initial billet length and smaller discard
ing stem displacement sVSt corresponding to the length.
increase in the flow stress associated with the ● Reducing the initial billet temperature gives
decreasing entry temperature E over the sealing a better product quality (higher proof stress,
stem displacement sVSt as shown in Fig. 3.54. higher tensile strength) over the length of the
The maximum sealing stem load in indirect hot extrusion.
extrusion with B R is not at the start of the ● The productivity in indirect hot extrusion is
extrusion process, as is the case with all other much higher than with direct hot extrusion
processes, but at the end of the extrusion process because of the significantly larger initial bil-
because of the billet cooling. let volume.
This can, in some cases, result in a limitation
of the billet length. The aim should, therefore, The disadvantages of indirect hot extrusion
be to keep the initial billet temperature B as compared with direct hot extrusion include:
low as possible and the container temperature
● The need to have a press specifically de-
R as high as possible. A container temperature
signed for indirect extrusion
R ⳱ 500 C and billet temperatures B ⳱ 600
● A special hollow stem the internal diameter
to 700 C have proved successful for the indirect
of which is determined by the circumscrib-
hot extrusion of brass. It is also beneficial to
ing circle of the section and which, in some
select the largest possible billet diameter to ob-
cases, has to be internally clad with a graph-
tain a better ratio of the thermal content of the
ite canister to avoid damage to the section
billet to the billet surface area.
● The need for a particularly long guided con-
tainer that usually has both zone and end face
3.2.6 Comparison of the Indirect Hot heating as well as zone cooling to guarantee
Extrusion Process with Direct Hot a constant container temperature over the
Extrusion container length
● Allowance should also be made for the fact
Compared with direct hot extrusion with a
shell and without lubrication, indirect hot extru- that there is no friction between the billet and
sion with a shell without lubrication offers the the container to prevent the billet outer zone
following advantages: flowing into the deformation zone. There is,
therefore, the risk that the impure billet sur-
● Because the sealing stem load is lower than face flows into the surface adjacent zones in
the direct extrusion load by the amount of the section. If this has to be avoided, then it
the friction or shearing load, it is possible to is necessary to extrude with a shell.
Fig. 3.54 Variation in the sealing stem load with the sealing stem displacement in indirect hot extrusion with an initial billet
temperature B that is higher than the container temperature R (e.g., copper alloys)
110 / Extrusion, Second Edition
Direct extrusion should be used for the extru- 3.2.7.1 Indirect Cold Extrusion with
sion of aluminum bright-finish alloys for prod- Lubrication and without a Shell
ucts with the best surface quality (anodizing
quality). Indirect hot extrusion lends itself to the Process Sequence in Indirect Cold Extru-
extrusion of high-strength aluminum alloys for sion with Lubrication and without a Shell.
products with less demanding surface proper- The process was first reported in [Sie 77]. In
ties. indirect cold extrusion with lubrication and
without a shell, a conical die as shown in Fig.
3.55 is used. The billet with a tapered end is
3.2.7 Indirect Cold Extrusion coated with the lubricant and loaded into the
The following processes fall into the heading container along with the die. Although, it is true
indirect cold extrusion: that in indirect extrusion a reduction of the fric-
tion between the billet and the container cannot
● Indirect cold extrusion without lubrication be obtained because there is no friction, it is pos-
and without a shell sible to reduce the friction between the die and
● Indirect cold extrusion without lubrication the container and between the die and the ma-
with a shell terial being extruded [Sie 77].
● Indirect cold extrusion with lubrication and With suitable design of the die and the sealing
without a shell stem and the correct selection of a lubricant that
usually has high thermal viscosity and high re-
The first two processes are indeed theoretically sistance to mechanical stresses, a lubricant buf-
possible but technically unimportant. In these fer forms at the die entry. Lubricant flows from
two processes the temperature increase in the de- this into the gap between the die external surface
formation zone from the deformation process and the container as well as into the working
can produce similar thermal conditions to indi- area between the die and the material being ex-
rect hot extrusion. The material flow when ex- truded (see Fig. 3.55).
truding through flat dies is approximately the Introducing seals between the sealing stem
same as in indirect hot extrusion, when fast ex- and the container and between the die and the
trusion speeds (sealing stem speeds) and high container gives a smooth transition between this
extrusion ratios are used. process to hydrostatic extrusion and the thick
A quasi-adiabatic deformation process, there- film process.
fore, takes place. The temperature increase in the Figure 3.56 shows the sealing stem and the
material being deformed in the deformation hollow stem as well as the container for a con-
zone is calculated from Eq 3.26. tainer diameter of 85 mm and a sealing stem load
Section exit temperatures of approximately of 8000 kN for indirect cold extrusion with lu-
300 C can be achieved in the indirect cold ex- brication. The sealing stem load force acting
trusion of Al99.5 with extrusion ratios over over the cross-sectional area of the container
V ⳱ 100 and high sealing stem loads. (sealing stem pressure) is 1400 N/mm2 (see Eq
The industrial application for the two pro- 3.56).
cesses, indirect cold extrusion without lubrica- Figure 3.57 shows the process sequence of
tion and without a shell, and indirect cold extru- indirect cold extrusion with lubrication without
sion without lubrication and with a shell, is a shell. It is recommended that loose dies be
restricted by the relatively high sealing stem used because of the extremely high sealing stem
load FVSt on the container cross-sectional area pressures usually used.
A0 required. This relative load is referred to as Material Flow in Indirect Cold Extrusion
the sealing stem pressure pVSt: with Lubrication and without a Shell. Figure
3.58 shows stages in indirect cold extrusion with
FVSt
lubrication. It can be seen that a quasi-stationary
pVSt ⳱ (Eq 3.56) deformation process forms within the die cone.
A0 The material flow is approximately the same in
all stages.
Indirect cold extrusion with lubrication and Figure 3.59 shows for different die opening
without a shell is more important for the extru- angles that the deformation zone extends into the
sion of composite materials, solders, powder adjacent billet volume with larger opening an-
metal (P/M) alloys and materials with relatively gles. However, it can be clearly seen that the
low flow stresses. billet volume outside the deformation zone is
Chapter 3: Rod and Tube Extrusion Processes / 111
completely unaffected by the deformation pro- cause there is no friction between the billet and
cess. The billet length is, as in all indirect extru- the container to be taken into account in any
sion processes, not limited by the material flow indirect extrusion process, then, according to Eq
but merely by the maximum possible length of 3.52:
the hollow stem calculated to resist buckling.
Axial Forces in Indirect Cold Extrusion
with Lubrication and without a Shell. Be- FVSt 艑 FHSt 艑 FM ⳱ FU
Fig. 3.55 Principal depiction of indirect cold extrusion with lubrication and without a shell [Sie 77]
Fig. 3.56 Sealing stem, hollow stem, and container for a container diam of 85 mm and a sealing stem load of 8000 kN
112 / Extrusion, Second Edition
As in direct cold extrusion in the die entry plane In cold working where the deformation tem-
the ideal axial compressive stress is, according perature is well below the material recrystalli-
to Eq 3.40: zation temperature, the influence of the mean
logarithmic principal strain rate u̇¯ g is usually
pXEid ⳱ k¯ f • ugges ⳱ k¯ f • lnV negligible. If this is not the case, then u̇¯ g is ob-
tained from Eq 3.18.
The mean flow stress for all the material being The ideal axial compressive stress pXEid
deformed in the deformation zone is: needed for perfect deformation in the die entry
plane multiplied by a factor C gives the actual
k¯ f ⳱ f (ūg, u˙¯ g, ) axial compressive stress pXE acting in the die
entry plane.
and can be obtained from the quasi-adiabatic According to Eq 3.41:
flow curves for the initial temperature E ⳱ 20
C and the mean principal strain (Eq 3.15): pXE ⳱ C • pXEid
Fig. 3.57 Process sequence for indirect cold extrusion with lubrication and without a shell. a, platen; b, die holder; c, hollow stem;
d, die; e, billet; f, container; g, sealing stem; h, lubricant film; i, separator; j, manipulator
Chapter 3: Rod and Tube Extrusion Processes / 113
In indirect cold extrusion with lubrication and Figure 3.60 shows the variation of the radial
without a shell of round bars through conical and axial compressive stresses over the billet
dies, then, from Eq 3.42 with fp ⳱ 1: length for indirect cold extrusion.
The sealing stem force referred to the con-
1 tainer cross-sectional area at the start of extru-
C ⳱ ⳱ 1.1
gU sion is obtained from:
Fig. 3.60 Fundamental variation in the compressive stress px and the radial compressive stress pr over the sealing stem displacement
sVSt in cold indirect extrusion with lubrication (l0, upset billet length in the container without the billet tip; D0, container
diam; lU, length of the deformation zone
The stem does not touch the billet during the In principle, hydrostatic extrusion can be used
compression of the hydrostatic medium to the for both hot and cold extrusion. However, in hot
starting pressure or during the extrusion process. extrusion it should be remembered that the seal-
The stem speed and the billet speed, therefore, ing system and the hydrostatic medium, as well
differ. The speed with which the billet moves in as the system for filling, removing, filtering, and
the direction of the die is proportional to the hy- cooling it, will all be exposed to high tempera-
drostatic volume displaced by the stem. During ture.
the semistatic extrusion process and neglecting To meet reproducible thermal conditions, the
the compressibility of the hydrostatic medium temperature of the hydrostatic medium in the
and the increase of the volume of the container container has to be equal to the initial billet tem-
associated with the elastic deformation to a first perature. The maximum permitted temperature
approximation: the billet speed ubillet is given by (flash point, chemical composition) of the hy-
the product of the stem speed uSt and the ratio drostatic medium therefore determines the max-
of the stem cross-sectional area Astem to the billet imum initial billet temperature possible. Con-
cross-sectional area Abillet: sequently, hydrostatic extrusion is primarily a
cold working process.
Astem One process limiting difficulty is the lack of
ubillet ⳱ ustem • (Eq 3.61)
Abillet a direct relationship between the billet speed and
the ram speed. It is, therefore, possible to have
Because the billet does not contact the con- an erratic extrusion with pressure variations in
tainer wall during extrusion and there is always the hydrostatic medium under stick slip condi-
the hydrostatic medium between the billet and tions. At the transition from sticking to slipping
the container wall, there is only fluid friction at conditions between the extruded material and
the billet surface apart from the area of contact the die the compressed hydrostatic medium can
between the die and the extruded product. This decompress and the billet be extruded at a high
is negligible when compared with the stresses speed. This reduces the pressure in the hydro-
and forces in hydrostatic extrusion. static medium and the deformation process
The characteristic feature of hydrostatic ex- stops. The hydrostatic medium then has to be
trusion is the fluid friction on the billet surface recompressed to the starting pressure to enable
apart from the contact between the die and the the deformation process to restart. This erratic
extruded billet. This fluid friction can be consid- extrusion occurs particularly when the friction
ered to be negligible when compared with the between the extruded material and the die is too
stresses and forces in hydrostatic extrusion. high and when the starting pressure is signifi-
cantly higher than the pressure required for the displacement and the closer is the relationship
semistationary deformation process. A large vol- between the billet speed and the ram speed.
ume of hydrostatic medium increases the like-
3.3.2 Process Sequence
lihood of its occurrence.
The lower the compressibility and the lower Figure 3.62 shows the process sequence in hy-
the volume of the hydrostatic medium, the drostatic extrusion. In principle, the billet can be
steeper the increase in pressure over the stem loaded between the stem and the container or
between the die and the container. The container semistationary deformation process (Fig. 3.63).
volume is filled with the hydrostatic medium The characteristic curve of the pressure increase
(usually castor oil) through a central hole in the against the stem displacement depends on the
stem. When the billet has been extruded to the compressibility and volume of the hydrostatic
discard length, the stem and the container travel medium, the elastic behavior of the pipe con-
back far enough to allow the discard to be pulled nections, the tooling, and the press frame. (Fig.
from the die with a manipulator and the section 3.64).
cut with a saw. Both the seal between the die The gradient of the characteristic curve in-
and the container and the seal between the stem creases as the volume of the hydrostatic medium
and the container are usually made from an elas- decreases. The compressibility of the hydrostatic
tomer with a copper beryllium support ring. medium also influences the profile of the pres-
These seals have a very limited life. sure increase characteristic curve.
Figure 3.64 shows the variation of the hydro-
3.3.3 Axial Loads in Hydrostatic Extrusion static pressure p with the stem displacement for
different hydrostatic media and billet lubricants.
The variation of the hydrostatic pressure in The curve with the highest pressures exhibits
the container with the stem displacement is usu- severe oscillations at the start of the process.
ally studied in hydrostatic extrusion (Fig. 3.63). These are associated with the erratic transition
If it is assumed that the frictional losses in the from sticking to slipping in the tribological sys-
stem/container seals are negligible, then the hy- tem extruded material/lubricant/die known as
drostatic pressure p in the container is equal to the stick slip phenomena. The friction in the tri-
the stem load FSt divided by the stem cross- bological system billet/lubricant/die is also very
sectional area ASt: important. Castor oil is usually used as the hy-
drostatic medium.
FSt If the hydrostatic medium dos not have suf-
p ⳱ (Eq 3.62)
ASt ficient lubrication properties, it is possible to add
lubricating additions to the hydrostatic medium
The stem load is, therefore, obtained from the or to lubricate the billet before it is loaded into
product of the stem cross-sectional area and the the press (see Fig. 3.64).
pressure. The fact that the hydrostatic medium Figure 3.65 shows in principle:
has to be initially compressed must be taken into ● The variation of the stem load FSt over the
account when considering the variation in the stem displacement w
hydrostatic pressure p over the stem displace- ● The variation of the hydrostatic pressure p
ment. The actual deformation process com- over the stem displacement w
mences after the start pressure p̂ needed for the ● The variation of the axial load FM exerted by
deformation has been reached. The pressure then the billet onto the die over the billet displace-
reduces to the constant value p̄ required for the ment s.
The stem load and the hydrostatic pressure
over the stem displacement have to follow the
same principle curve because, according to Eq
3.61, the stem load is derived from the product
of the hydrostatic pressure and the stem cross-
sectional area, which is a constant.
The axial load on the die FM behaves differ-
ently because it is the product of the billet cross-
sectional area and the hydrostatic pressure:
F̂M ⳱ p̂ • ABillet (Eq 3.65) product and the die, the same die aperture angle
and the same extrusion ratio, therefore: The ax-
The maximum value F̂M is approximately 15% ial load F̄M on the die for the semistatic defor-
higher than the value F̄M: mation process is approximately the same as for
direct cold extrusion with lubrication, indirect
Fˆ M ⳱ 1.15 • F¯ M (Eq 3.66) cold extrusion with lubrication, and hydrostatic
cold extrusion.
If the axial load FM applied by the billet onto
the die is plotted against the billet displacement
3.3.4 Products
s, the curve FM ⳱ f (s) is comparable to the vari-
ation FM ⳱ f (s) for other extrusion processes. Figure 3.66 shows interrupted extrusions of
For approximately the same frictional condi- copper wire from copper billets with extrusion
tions in the interaction between the extruded ratios of V ⳱ 50 and an initial billet temperature
Fig. 3.64 Variation of the hydrostatic pressure over the stem displacement for different hydrostatic media and billet lubrication
[Fio 67]
Chapter 3: Rod and Tube Extrusion Processes / 119
of 20 C and V ⳱ 800, and an initial billet tem- with lubrication and no shell. Hydrostatic extru-
perature of 300 C and a hydrostatic pressure of sion appears to be particularly suitable for the
16 kbar. manufacture of helical sections (see Fig. 3.68).
With pressures up to 20 kbar, hydrostatic ex- In this case, the billet rotates in the container
trusion can be used for the cold extrusion of alu- during extrusion.
minum alloys, copper and copper clad alumi- Figure 3.68 shows helical gear bars extruded
num billets and, to a limited degree, even steel from case-hardening steel cylindrical billets.
billets to sections (see Fig. 3.67). These helical gear bars can be produced by ex-
It therefore competes with indirect cold extru- trusion only if the billet can rotate in the con-
sion with lubrication and without a shell and, to tainer completely free of any frictional restraint.
some degree, also with direct cold extrusion This requirement is met in hydrostatic extrusion.
Fig. 3.65 Variation of the stem load FSt and the hydrostatic pressure p over the stem displacement w as well as the variation of the
axial force FM over the billet displacement s.
120 / Extrusion, Second Edition
Fig. 3.67 Hydrostatic pressure against the extrusion ratio for different materials (Source: ASEA). 1, high speed steel; 2, mild steel;
3, soft unalloyed mild steel; 4, commercial copper (Cu 99.5%); 5, aluminum alloy 7075; 6, pure aluminum (Al 99.5)
Chapter 3: Rod and Tube Extrusion Processes / 121
Fig. 3.68 Extruded bars with helical gear teeth in case-hardening steel (Source: ASEA)
Fig. 3.71 Hydrostatic pressure plotted against the extrusion ratio for different copper contents. A, 100% Cu (pure Cu); B, 20% Cu;
C, 15% Cu; D, 10% Cu; E, 0% Cu (pure Al) (Source: ASEA)
Fig. 3.74 Conform extrusion press. (a) Radial. (b) Tangential extrusion exit. 1, friction wheel; 2, seal segment; 3, sealing piece; 4,
die; 5, feedstock (wire); 6, extrusion [Eth 84b]
124 / Extrusion, Second Edition
strength. The cable sheathing alloys are stan- The material flow necessitates longitudinal
dardized in DIN 17640 part 2. Low-strength al- welds. Particular attention must be paid to these
loys are usually alloyed with tellurium and cop- potential sources of defects. The boundary sur-
per. Higher-strength alloys, which are usually face between the extruded and the newly filled
used for communication cables, contain anti- metal (transverse weld) extends as a tongue over
mony. The higher-strength alloys can, however, approximately 20% of an extrusion charge and
be processed only on extrusion presses. can be scarcely recognized by metallography
In lead sheathing, the extrusion process has [Rie 63].
had competition for over 70 years from the con- The wall thickness of the extruded cable
tinuously operating screw press, the design of sheath can be set and adjusted by axial move-
which is very similar to plastic extruders. They ment of the die [Rie 72].
are preferred for pure and low-alloy lead be- A cooling ring located immediately behind
cause the machines are less expensive than cable the die sprays water onto the extrusion providing
sheathing processes. They are not discussed rapid cooling and hinders coarse grain formation
here. in the lead mantle as well as damage of the tem-
perature-sensitive cable insulation. The cooled
3.6.3.2 Cable Sheathing with Lead cable is coiled directly behind the press.
In lead cable sheathing, liquid metal is poured As mentioned previously, the stop mark be-
into a vertical container. Usually, it is filled from tween two extrusions, during which the extru-
an electrically heated crucible containing several sion is stationary for several minutes, is a prob-
tons of the melt through a floor valve with vari- lem. The bamboo ring that forms has a reduced
ous flow systems at a maximum temperature of wall thickness due to the elastic deformation of
450 C. the die when the load is reduced and the sub-
The cast lead should bond well with the dis- sequent reduction in the gap between the die and
card from the previous filling on the die head to the hollow mandrel. The strength and structure
prevent possible defects from inclusions. Air also changes at these stop marks. The pressure
blisters should not form during filling. The lead at the die also reduces during extrusion from the
is, therefore, usually filled under vacuum to- start of extrusion to the end, resulting in wall
gether with a lost head that is sheared after so- thickness variations.
lidification at the top edge of the container Careful control of the die setting during ex-
[Rie 63]. trusion and when stopped are used to compen-
The metal solidifies in the water-cooled con- sate for this in order to obtain a constant wall
tainer under a small load applied by the stem thickness. Built-in thermocouples are used to
within 5 to 10 minutes after which the extrusion carefully monitor the tooling temperature. Heat-
process can begin. ing elements are used to control the temperature.
The metal then flows into the bifurcated hol- So-called continuous cable sheathing extru-
low mandrel from two sides and is pressed into sion that avoids the stop mark, which is also
the prechamber. It is then pressed onto the cable used for lead, is discussed in the section on alu-
and forms the cable mantel as it leaves the die minum.
(Fig. 3.83). This also applies to aluminium cable The machines used for cable sheathing extru-
extrusion. sion with lead range from 6 to 30 MN press
power with a container capacity of 135 to 1000 ● Another method is to produce a temperature
kg lead. The container diameters are selected to profile of approximately 100 C between the
give a specific pressure of 350–450 N/mm2. two billet ends in the induction billet furnace
Mantle diameters up to 110 mm are standard. [Ste 70]. A uniformly heated billet barrels to
the container wall during upsetting and seals
3.6.4 Sheathing with Aluminum the air in on the die side. In contrast, a billet
with a temperature profile upsets initially at
the hotter side next to the die. In vertical con-
3.6.4.1 Aluminum as a Cable Sheathing tainers the billet contacts the container wall
Material from the bottom to the top so that the air can
Aluminum is significantly lighter than lead emerge from the top. Air trapped in front of
and its high conductivity enables it to be used the die results in blisters and tearing of the
as an earth and with communication cable as the metal mantle.
screen against electromagnetic interference. The If the operating sequence is interrupted,
higher strength compared with lead usually equalization of the temperature gradient be-
avoids the need for protection against mechan- tween the billet front and end occurs and, con-
ical damage [Sün 69]. sequently, air blisters cannot be excluded.
The higher bending strength of aluminum Therefore, the process mentioned first of sealing
compared with lead is, however, a disadvantage and evacuating is preferred.
because the aluminum sheath extruded onto the
cable has to be corrugated for diameters above
approximately 50 mm. A further disadvantage
of aluminum is the corrosion susceptibility that
necessitates careful protective coating, e.g., with
bitumen and extruded polyvinyl chloride.
of the container through the die. As soon as the 3.7.1 Direct Tube Extrusion
end of extrusion is reached, and the stem with-
Direct tube extrusion can, according to Fig.
drawn to load the next billet, the auxiliary con-
3.88, be divided into direct hot tube extrusion
tainer begins to move upward and the cable
and direct cold tube extrusion. The latter is used
sheath continues to be extruded, using its metal
only in special cases.
filling without interruption but with a slower
Direct hot tube extrusion can be divided into
speed. At the start of this process, a valve in the
tube extrusion over a fixed mandrel and tube ex-
die head closes to prevent metal flowing up into
trusion over a moving mandrel.
the main container.
The movement of the auxiliary container lasts
long enough to enable a new billet to be loaded 3.7.1.1 Direct Hot Tube Extrusion over a
and the container evacuated. The valve reopens Fixed Mandrel
during the subsequent extrusion and the cycle
restarts. In direct hot tube extrusion without a shell
over a fixed mandrel (Fig. 3.89), prebored billets
are usually used. The billet bore is slightly
smaller than the mandrel shaft diameter.
3.7 Tube Extrusion Process When the mandrel enters the billet, the bore
acts as a pilot hole. Once the mandrel is in the
Klaus Siegert* final position, the extrusion process commences
by moving the stem forward. The billet is then
As mentioned previously, tube extrusion in pushed over the mandrel.
this context concerns the extrusion of seamless As with all other direct section and tube ex-
tubes over a mandrel. The extrusion of tubes trusion processes, there is friction between the
through a welding chamber die is, therefore, material being extruded and the container wall
classified under the section extrusion. as well as, specific to direct tube extrusion, fric-
Tube extrusion can be classified into: tion between the material being extruded and the
● Direct tube extrusion mandrel surface. When the set discard length is
● Indirect tube extrusion reached, the mandrel is withdrawn. The con-
tainer then opens slightly so that the dummy
There are also special processes, including hy- block and the discard can be pushed out of the
drostatic extrusion, that can be used for tube ex- container. As the stem moves back, a shear
trusion. This is discussed in the section on hy- mounted on the press platen separates the dis-
drostatic extrusion. card (Fig. 3.89).
Fig. 3.89 Process sequence for direct hot tube extrusion without a shell over a fixed mandrel [Bis 75]
This operating sequence can be used for direct tive movement between the material being ex-
hot tube extrusion of aluminum alloys. As with truded and the mandrel outside the deformation
hot section extrusion of aluminum, lubrication zone that forms in front of the die. There is,
is never used. therefore, no friction in this region. There is,
however, an increase in the relative speed be-
3.7.1.2 Direct Hot Tube Extrusion with a tween the material being extruded and the man-
Moving Mandrel drel in the region of the deformation zone up to
the tube exit speed less the mandrel or stem
If extrusion is carried out with a moving man- speed. Friction has to be taken into account in
drel as shown in Fig. 3.90, a cylindrical mandrel this region. The relative speed between the man-
without a mandrel tip is used. It is also possible drel and the material being extruded is then
to use slightly conical mandrels. lower.
The mandrel can travel with the stem speed, The mandrel can also move relative to the
e.g., coupled to the stem so that there is no rela- stem when it is possible that the mandrel is
132 / Extrusion, Second Edition
Fig. 3.90 Process sequence for direct hot tube extrusion with a shell over a moving mandrel [Zil 77, Bis 75, Bis 77]
pulled forward by the friction between the ma- The shell adhering to the container wall has
terial being extruded and the mandrel. This is to be removed at the end of extrusion by a spe-
referred to as direct hot tube extrusion over a cial operation, which is considered to be a dis-
moving mandrel with relative movement. advantage.
The advantage is, however, that in extrusion
3.7.1.3 Direct Hot Tube Extrusion with a with a shell, oxide residues and impurities from
Shell the billet peripheral zone finish up in the shell
and cannot flow into the extruded product.
It is possible to extrude with a shell in both Figure 3.90 shows the operating sequence for
hot tube extrusion with a fixed and with a mov- hot tube extrusion with a shell over a moving
ing mandrel. mandrel. It is possible to pierce the billet in the
A shell is formed between the dummy block container. It is also possible, as shown in Fig.
and the container wall in direct hot tube extru- 3.90, to use prebored billets. Then, a longer ini-
sion with a shell if the gap between the dummy tial billet length can be used. The removal of the
block and the container wall is selected cor- shell is not shown. The shell can be removed in
rectly. the same way as in direct hot extrusion either by
Chapter 3: Rod and Tube Extrusion Processes / 133
a separate cleaning cycle or a combination drel surface. Therefore, similar conditions occur
block. at the mandrel as at the container wall. This is
It is usual to pierce the billet in the press when discussed in section 3.1.1.4.
extruding with a moving mandrel. The billet is If l0 is the length of the billet upset in the
initially upset in the container. The stem then container over the mandrel, s1 is the upset dis-
moves slightly back so that the material dis- placement and lR is the discard length, which is
placed by the mandrel during piercing can flow equal to the difference of the length l0 and the
in the opposite direction from the piercing di- shaft length in contact with the material in con-
rection. tact, then the mandrel tensile load is given by:
After the piercing operation, the extrusion
process continues until the preset discard thick- FD ⳱ (l0 ⳮ lR Ⳮ s1 ⳮ sSt) • DDS • p • sS1
ness is reached. The mandrel and the stem then DDS Ⳮ DD
return. Ⳮ • p • lR • sS2 (Eq 3.67)
2
The container is also opened sufficiently to
enable the tube to be sawn from the discard.
A cleaning disc then pushes the discard and An average mandrel diameter is assumed for the
the shell into a discard tool loaded between the friction between the material being extruded and
platen and the container. This is the usual op- the mandrel tip:
erating sequence for the direct hot tube extrusion
of copper materials. DDS Ⳮ DD
2
3.7.1.4 Analysis of the Axial Forces in
The critical shear stress sS1 between the material
Direct Hot Tube Extrusion
being extruded and that sticking to the shaft sur-
Figure 3.91 shows the conditions in direct hot face depends on the localized temperature.
tube extrusion over a stationary mandrel. This This is lower than that in the deformation
extrusion process is usually carried out without zone. The shear stress sS1 is therefore higher than
a lubricant, e.g., aluminum. the shear stress sS2 in the deformation zone in
A thin layer of the material being extruded the boundary surface along the mandrel tip.
coats the mandrel. As the billet is pushed over The force needed to shear the material being
the mandrel, the material being extruded shears extruded along the container wall is obtained
along a boundary surface concentric to the man- from Eq 3.44:
Fig. 3.91 Direct hot tube extrusion over a fixed mandrel (e.g., of aluminum) without lubrication. D0, container diam; DDS, mandrel
bar diam; Da, tube external diam; Di, tube internal diam; FSt, stem load; FD, mandrel load; l0, upset billet length; lR,
discard length; SSt, stem displacement; S1, upset displacement [Zie 78]
134 / Extrusion, Second Edition
冤 冥
drel, the extrusion ratio is, according to Eq 3.1: 3
ūg ⳱ 2 • ln (Eq 3.75)
D*
S
Ⳮ2
D20 ⳮ D2DS D*
V⳱ (Eq 3.69) 0
D2a ⳮ D2i
The estimation of the entry temperature E is
According to Eq 3.14, the logarithmic principle more difficult. With increasing ram movement,
strain is: the billet volume enters the deformation zone
with an increasing temperature because of the
D20 ⳮ D2DS friction between the mandrel and the material
uges ⳱ lnV ⳱ ln (Eq 3.70)
Da2 ⳮ Di2 being extruded as well as the friction between
the container wall and the material being ex-
The axial force needed for deformation in the truded, if the initial billet temperature is equal
deformation zone FM is analogous to Eq 3.13: to the container temperature.
Initially, the entry temperature E is equal to
p the initial billet temperature B. It then increases
FM ⳱ C • ugges • k¯ f • (D20 ⳮ D2DS) (Eq 3.71)
4 continuously until the end of the extrusion pro-
cess, providing a temperature profile produced
To determine the mean flow stress k̄f from by an induction billet furnace or a decreasing
quasi-adiabatic flow curves, it is necessary to stem speed over the stem displacement is not
know the temperature E with which the mate- used to give a constant entry temperature E
rial being deformed enters the deformation zone, over the stem displacement.
as well as a valid mean logarithmic strain ūg for The temperature increase in the deformation
the material being extruded in the deformation zone corresponding to the work that is converted
zone and a mean logarithmic strain rate ū˙ g: to heat is given by:
stress is constant, which is the case with a con- creasing entry temperature over the stem move-
stant entry temperature E. This then gives a ment.
constant exit temperature S over the stem dis- In the extrusion of copper alloys the initial
placement s. This is known as isothermal tube billet temperature of 600 to 800 C is above the
extrusion. maximum tool temperature of approximately
If the initial billet temperature B is higher 500 C. Consequently, mandrel cooling is used
than the container temperature, which is the case to ensure that the mandrel is not overheated.
in copper tube extrusion, then the billet volume
3.7.2 Indirect Tube Extrusion
enters the deformation zone at an increasingly
lower temperature according to section 3.1.2.5. Indirect tube extrusion can be divided accord-
This tendency compensates the temperature in- ing to Fig. 3.92 into indirect tube extrusion over
creases from the friction between the container a stationary mandrel and indirect tube extrusion
wall and the material being extruded. In addi- over a moving mandrel.
tion, the temperature increase in the deformation Both processes can, in principal, take place
zone increases with decreasing entry tempera- with and without mandrel lubrication and with
ture because the flow stress increases. The end and without mandrel cooling. If the billet tem-
effect is a decrease in the exit temperature be- perature is higher than 450 C, mandrel cooling
cause of the predominating influence of the de- should be used.
Fig. 3.93 (a) Process sequence in indirect tube extrusion over a fixed mandrel (stages 1–4). (b) Process sequence in indirect tube
extrusion over a fixed mandrel (stages 5–8). a, extrusion press platen; b, hollow stem holder; c, hollow stem; d, die; e,
billet; f, container; g, sealing stem; h, mandrel; i, mandrel tip
136 / Extrusion, Second Edition
FVSt ⳱ FM Ⳮ FD
where
FM ⳱ FHSt
[Ake 66]: R. Akeret and A. Künzli, Ermittlung [Con 85]: Low Cost Molten Feed Boosts Con-
der Formänderungsfestigkeit kf von Alumin- tinuous Extrusion, Metallurgia, Vol 32 (No.
ium-Legierung mit hilfe von Torsionsver- 6), 1985, p 243–245
suchen und Vergleich der Ergebnisse mit [Daw 96]: J.R. Dawson, Conform Machinery
denjenigen von Strangpreßversuchen (Deter- for the Manufacture of Round and Multi-Part
mining the Flow Stress of Aluminum Alloys Aluminium-Tube, Alum. Today, April/May
Using Torsion Tests and Comparison of the 1996, p 11, 12, 17
Results with Those from Extrusion Trials), Z. [DGM 78]: Atlas der Warmformgebungseigen-
Metallkd., Vol 57 (No. 11), 1966, p 789–792 schaften von Nichteisenmetallen: Bd. 1 Alu-
[Ake 68]: R. Akeret, Untersuchungen über das minium-Werkstoffe, Bd. 2 Kupfer-Werkstoffe
Strangpressen unter besonderer Berücksichti- (Atlas of Hot-Working Properties of Non-Fer-
gung der thermischen Vorgänge (Investiga- rous Metals: Vol 1, Aluminum Alloys; Vol 2,
tions into Extrusion with Specific Consider- Copper Alloys), Akeret, Jung, Scharf, Ed.,
ation of the Thermal Processes), Int. DGM, 1978
Leichtmetalltagung, Vol 5, Leoben/Wien, [DIN]: DIN 57255A4 ⳱ VDE 0255 A4: Kabel
1968, p 304–307 mit massegetränkter Papierisolierung und
[Ake 71]: R. Akeret, Z. Metallkd., Vol 62 (No. Metallmantel für Starkstromanlagen (Cable
6), 1971 with Impregnated Paper Insulation and Metal
[Alu]: Aluminium-Fließkurven (Aluminum Flow Mantle for High Power Plants)
Curves), Fließkurven-Alu: 2731/101, 2732/ [Doe 86]: E. Doege, H. Meyer-Nolkemper, and
101, 2733/101, des Forschungsinstitutes der I. Saeed, Fließkurvenatlas metallischer Werk-
Schweizerischen Aluminium-AG stoffe: mit Fließkurven für 73 Werkstoffe u. e.
[ASEA 70a]: Quintus Hydrostatic Extrusion grundlegenden Einführung (Flow Curve Atlas
Press Type QE, ASEA pamphlet AQ 14–102T of Metallic Materials with Flow Curves for
[ASEA 70b]: Hydrostatisches Strangpresen 73 Alloys and a Fundamental Introduction),
(Hydrostatic Extrusion), ASEA brochure AQ Hanser Verlag München, 1986
14–101T [Due 69]: W. Dürrschnabel, Der Werkstofffluß
[ASEA 71a]: Hydrostatisches Strangpressen beim Strangpressen von NE-Metallen (Mate-
nach dem Quintus-Verfahren (Hydrostatic Ex- rial Flow in the Extrusion of NF Metals) I, II,
trusion Using the Quintus Process), ASEA III, Metall., Vol 22, 1968, p 426–437, 995–
brochure AQ 14–107T 998, 1215–1219
[ASEA 71b]: Herstellung von kupferumhülltem [Eis 31]: W. Eisbein, “Kraftbedarf und
Aluminium—ein neues Quintus-Verfahren Fließvorgänge beim Strangpressen” (“Load
(Production of Copper Clad Aluminum—A Requirements and Flow Processes in Extru-
New Quintus Process), ASEA brochure AQ sion”), Technische Hochschule (technical uni-
14–106T versity), Berlin, thesis, 1931, (quoted in [Rat
[Bis 73]: A. Biswas, Direktes, Indirektes und 66])
hydrostatisches Strangpressen (Direct, Indi- [Eth 84]: C. Etherington and H.K. Slater, The
rect and Hydrostatic Extrusions), Z. Alumin- Extrusion of Aluminium and Its Alloys by
ium, Vol 49 (No. 4), 1975, p 296–299 and Conform Process; Extrusion Productivity
(No. 5), p 352–356 through Automation, Third Int. Aluminium-
[Bis 75]: A. Biswas and F.-J. Zilges, Indirektes Extrusion Seminar (Atlanta, GA), Vol 2, 1984
Strangpressen von Kupfer-Werkstoffen (In- [Eth 84b]: G. Etherington, Update on Con-
direct Extrusion of Copper Alloys), Z. Me- form—The Continuous Extrusion Forming of
tallkd., Vol 29 (No. 4), 1975, p 375–380 Metals, Chart. Mech. Eng., Vol 31, 1984, p
[Bue 70]: H. Buehler, H.G. Hoepfner, and J. 28–32
Loewen, Die Formänderungsfestigkeit von [Fel 56]: P. Feltham, Extrusion of Metals, Metal
Aluminium und einigen Aluminium-Legi- Treatment, Vol 23, 1956, p 440–444
erungen (The Flow Stress of Aluminum and [Fel 69]: H.D. Feldmann, Betrachtungen zum
Some Aluminum Alloys), Z. Bänder, Bleche, hydrostatischen Strang-und Fließpressen von
Rohre, Vol 11 (No. 12), 1970, p 645–649 Metallen (Considerations on Hydrostatic Ex-
[Con 84]: Conform . . . nun das vollendeteste trusion and Impact Extrusion of Metals Parts
Stranggußverfahren (Conform . . . Now the 1 and 2), Teil 1 und 2, TZ für prakt, Metall-
Most Complete Continuous Coating Process), bearbeitung, Vol 63 (No. 3), 1969, p 116–119
Metallurgia, Vol 51 (No. 6), 1984, p 218–231 and (No. 8), p 426–433
138 / Extrusion, Second Edition
[Fio 63]: R.-J. Fiorentino et al., Advances in Hy- [Mad 87]: B. Maddock and B. Eng, Aluminium
drostatic Extrusion, Tool and Manufacturing Rod and Other Products by Conform, Wire
Engineer, Aug 1963, p 77–83 Ind., The British Wire Journal, Dec 1987, p
[Fio 67]: R.-J. Fiorentino et al., New Develop- 720–731
ments in Hydrostatic Extrusion, Proc. Int. [Met 85]: Low Cost Molten Feed Boosts Con-
Conf. Manuf. Techn., Sept 1967, p 941–954 tinuous Extrusion, Metallurgia, Vol 32 (No.
[Fio 72]: R.-J. Fiorentino et al., The Thick Film 6), 1985, p 243–245
Hydrostatic Extrusion Process, Metall. and [Mue 84]: K. Müller, Untersuchungen zu den
Met. Form., June 1972, p 200–205 Reibungsverhältnissen beim Warm-Strang-
[Fio 74]: R.-J. Fiorentino et al., Some Practical pressen von Rohren aus Aluminium-Legi-
Considerations for Hydrostatic Extrusion I, II, erung bei Verwendung von Preßdornen (In-
Metall. and Met. Form., July 1974, p 193– vestigations into the Friction Behavior in the
197; Aug 1974, p 210–213 Hot Extrusion of Aluminum Alloy Tubes Us-
[Har 83]: G. Hartmann, Untersuchungen über ing Mandrels), Forschungsbericht, VDI-Z,
Kräfte und Butzengrößen beim Lochen von Reihe 5, Nr. 76, 1984
Aluminium-Werkstoffen gegen Matrize (Inves- [Par 84]: J.A. Pardoe, Conform Continuous Ex-
tigations into the Loads and Discord Sizes in trusion Process—Its Contribution to Energy
the Piercing of Aluminum Alloys against Like Conservation, Met. Technol., Vol 11, Aug
Die), D83, Technische Universität Berlin, 1984, p 358–365
D83, 1985 [Par 86]: R.D. Parkinson, Continuous Clad-
[Haw 91a]: D.J. Hawkes and R.E. Morgan, ding-Conform Process, Wire Ind., The British
Conform Extrusion, Wire Ind., June 1991 Wire Journal, No. 4, 1986, p 3
[Hei 77]: H. Heimburg, Verbesserung der Pro- [Pea 61]: C.E. Pearson and R.N. Parkins, The
duktqualität und Wirtschaftlichkeit beim Extrusion of Metals, Chapman & Hall, 1961
Strangpressen von Messing (Improving the [Pet 59]: E. Petsch, Neues Indirekt-Strangpress-
verfahren für Metalldraht (New Indirect Ex-
Product Quality and Economics of Brass Ex-
trusion Process for Metal Wire), Z. Metallkd.,
trusion), Z. Metallkd., Vol 31 (No. 4), 1977,
Vol 50 (No. 11), 1959, p 629–637
p 414–417
[Pug 65]: H.W.D. Pugh and A.W. Low, Hydro-
[Joh 68b]: S. Johnson, Fortschritte beim hy-
static Extrusion of “Difficult” Metals, Sheet
drostatischen Strangpressen (Advances in Met. Ind., Aug 1965, p 572–594
Hydrostatic Extrusion), Z. Draht-Welt, Vol 54 [Pug 72]: H.W.D. Pugh and C.J.H. Donaldson,
(No. 4), 1968, p 209–213 Hydrostatic Extrusion—A Review, Annals of
[Kom 89]: Kombinat VEB Kabelwerk Ober- the CIRP, Vol 21 (No. 2), 1972, p 167–186
spree: Kabel und Leitungen (Cable and Con- [Rat 66]: C. Rathjen, “Untersuchungen über die
ductors), VEB-Verlag Technik Berlin, 1989 Größe der Stempelkraft und des Innendruckes
[Lan 71]: G. Lange, Der Wärmehaushalt beim im Rezipient beim Strangpressen von Metal-
Strangpressen (Heat Balance in Extrusion), Z. len” (“Investigations into the Size of the
Metallkd., Vol 62 (No. 8), 1971, p 571–579 Stamp Force and the Internal Pressure in the
[Lan 85]: I. Langerweger and B. Maddock, Svi- Container in the Extrusion of Metals”), TH-
luppi nell’ estrusione continua: il processo Aachen, Diss., 1966
conform, Technologie, Vol 3 (No. 2), 1985, p [Rie 63]: H. Riemann, Einrichtungen zum Bes-
56–59 chicken von Bleipressenrezipienten (Systems
[Lan 88]: I. Langerweger and B. Maddock, Re- for Loading Lead Extrusion Containers),
cent Developments in Conform and Castex Draht, Vol 14 (No. 8), 1963
Continuous Extrusion Technology, Light Met. [Rie 72]: H. Riemann, Kontinuierliche Umman-
Age, Aug 1988 telung von Kabeln mit Bleir (Continuous
[Lau 76]: Strangpressen: Verfahren, Maschi- Sheathing of Cables with Lead), Bleilegierun-
nen, Werkzeuge (Extrusion: Processes, Ma- gen und Aluminium, Draht, Vol 4, 1972
chining, Tooling), K. Laue and H. Stenger, [Rup 80b]: D. Ruppin and K. Müller, Kalts-
Ed., Aluminium Verlag, Düesseldorf, 1976, trangpressen von Aluminium-Werkstoffen
ISBN 3-87017-103-0 mit Druckfilm-Schmierung I bis III (Cold Ex-
[Len 69]: B. Lengyel and L.E. Culver, Proper- trusion of Aluminum Alloys with Pressure
ties of Materials Extruded by Orthodox Hy- Film Lubrication I to III), Z. Aluminium, Vol
drostatic Extrusion, J. Inst. Met., Vol 97, 56 (No. 4), 1980, p 263–268; (No. 5), p 329–
1969, p 97–103 331; and (No. 6), p 403–406
Chapter 3: Rod and Tube Extrusion Processes / 139
[Sac 37]: G. Sachs, Spanlose Formgebung der Z (progress report Vol 2), Vol 2 (No. 51),
Metalle (Chipless Shaping of Metals), Hand- VDI-Verlag GmbH, Düsseldorf
buch der Metallphysik, Vol 3 (No. 1), 1937, [Stu 68]: H.P. Stuewe, Einige Abschätzungen
(quoted in [Rat66]) zum Strangpressen (Some Assessments of
[Sie 76a]: K. Siegert, “Untersuchungen über das Extrusion), Z. Metallkd., Vol 22 (No. 12),
direkte, indirekte und hydrostatische Strang- 1968, p 1197–1200
pressen” (“Investigations into Direct, Indirect [Stu 71]: H.P. Stuewe, Fließspannung und Ver-
and Hydrostatic Extrusion”), Technische formungsgeschwindigkeit beim Strangpres-
Universität Berlin, Diss., 1976 sen (Flow Stress and Deformation Rate in Ex-
[Sie 76b]: K. Siegert, Betrachtung der Rei- trusion), Z. Metallkd., Vol 62 (No. 10), 1971,
bungsvorgänge beim Strangpressen (Consid- p 697–701
eration of the Friction Processes in Extru- [Sün 69]: H. Sünderhauf, Die Verwendung von
sion), in Strangpressen Berichte des Aluminium in der Kabeltechnik (The Appli-
Symposiums in Bad Nauheim (in the Extru- cation of Aluminum in Cable Technology),
sion Papers of the Bad Nauheim Symposium), Aluminium, Vol 45, 1969, p 111–114
1976, DGM e.V. Oberursel, 1976 [Wil 69]: H. Wilhelm, “Untersuchungen über
[Sie 77]: W. Ziegler and K. Siegert, Spezielle den Zusammenhang zwischen Vickershärte
Anwendungsmöglichkeiten der Indirekten und Vergleichsformänderung bei Kaltform-
Strangpreßmethode (Special Application Pos- vorgängen” (“Investigations into the Rela-
sibilities of the Indirect Extrusion Method), Z. tionship between Vickers Hardness and
Metallkd., Vol 31 (No. 8), 1977, p 845–851 Equivalent Strain in Cold-Working Pro-
[Sie 78]: Siegert, K., Indirektes Strangpressen cesses”), Bericht aus dem IFU-Stuttgart (Re-
von Messing (Indirect Extrusion of Brass), Z. port from the IFU), No. 9 Girardet, Essen,
Metallkd., Vol 32 (No. 12), 1978, p 1243– 1969
1248 [Zie 73]: W. Ziegler and K. Siegert, Indirektes
[Sie 80]: K. Siegert, Indirektes Strangpressen Strangpressen von Leichtmetall (Indirect Ex-
trusion of Aluminum), Z. Metallkd., Vol 64
von Aluminium-Legierungen (Indirect Extru-
(No. 4), 1973, p 224–229
sion of Aluminum Alloys), Tagungsbericht
[Zie 78]: W. Ziegler, Direktes, indirektes und
der 7, Intern (Report of the Seventh Interna- hydrostatisches Strangpressen im Vergleich
tional Aluminum Conference), Leichtmetall- (Comparison of Direct, Indirect and Hydro-
tagung Leoben/Wien, 1981, p 290–292 static Extrusion), Z. Drahtwelt, Vol 12, 1978,
[Ste 70]: A. Steinmetz, Doppeltwirkende Presse p 475–481
zum Ummanteln elektrischer Leiter mit Alu- [Zil 77]: F.-J. Zilges, Indirektes Strangpressen
minium (Double Acting Press for Sheathing von Rohren aus Aluminium-und Kuper Werk-
Electrical Conductors with Aluminum), Alu- stoffen (Indirect Extrusion of Aluminum and
minium, Vol 46, 1970, p 3–6 Copper Alloy Tubes), Z. Metallkd., Vol 31
[Stre 82]: W. Strehmel, Untersuchungen zum (No. 4), 1977, p 151–156
rechnergestützten direkten Strangpressen von [Zwe 60]: W.V. Zwehl, Bewährung von Stark-
Aluminium-Legierungen (Investigations into stromkabel mit Aluminiummantel (Protection
Computer Controlled Direct-Extrusion of of Power Cables with Aluminum Cladding),
Aluminum Alloys), Fortschrittsberichte, VDI- Aluminium, Vol 36, 1960 p 666–671
Extrusion: Second Edition Copyright © 2006 ASM International®
M. Bauser, G. Sauer, K. Siegert, editors, p 141-194 All rights reserved.
DOI:10.1361/exse2006p141 www.asminternational.org
CHAPTER 4
Metallurgical Principles
Martin Bauser*
4.1 Introduction literature, e.g., [Hor 67, Guz 70, Ber 83, Sch 81,
Dah 93, Hou 93, Blu 93, Alt 94].
THE EXTENSIVE USE of metals over thou- This materials science chapter is concerned
sands of years, but in particular during the in- only with metals. The atoms are held together
dustrial age, can be attributed to their specific by the so-called “metallic bond,” which differ-
properties. In addition to their good electrical entiates them from the nonmetals (covalent
conductivity—associated with good thermal bond, ionic bond). A characteristic of this me-
conductivity—and visual properties, the most tallic bond is the ease of movement of the outer
important are the mechanical properties and the electrons, which are no longer attached to indi-
good workability. The use and range of appli- vidual atoms but form an electron gas. This mo-
cation of different metals depends on these and bility of the electrons is the reason for the good
many other properties, including, for example, electrical conductivity of metals.
the corrosion resistance. However, the produc- Nonmetallic crystalline materials can, as a
tion costs also play a decisive role. rule, be extruded only with difficulty, if at all.
These extend from the accessibility and the There is insufficient ductility in the working
extraction of the ore, the cost in the refining up range of temperatures and pressure. Glass with
to and including the casting and processing. Ex- its amorphous structure is, however, an excep-
trusion is suitable as a deformation process in tion because it softens on heating.
different ways for the different materials. The Recently, metal and nonmetal composite ma-
well-used expression “extrudability” is a way of terials have been extruded. Nonmetallic particles
expressing this. or fibers are uniformly embedded in a metallic
Knowledge of deformation technology alone matrix, usually artificially, to improve the me-
is not sufficient to be able to understand and con- chanical properties and often to reduce wear.
trol the processes taking place during extrusion. These materials are also discussed briefly in this
The quality of the billet materials, the processes chapter.
taking place within the extruded material during
extrusion, and the properties of the extruded sec-
tion can be understood only from a metallurgical 4.2 Structure
viewpoint.
This chapter, therefore, explains the basic ter-
minology of metallurgy—naturally in the con- 4.2.1 Lattice Structure Single Phase
text of the aims of this book—to provide the All metals consist of crystallites (small crys-
tools needed by those involved in extrusion. tals), the arrangement, size, and shape of which
More detailed explanations can be found in the are referred to as the structure. Polishing of
*Casting and Cast Structure, Homogenizing of Aluminum Alloys, Wolfgang Schneider; Casting and Cast Structure of Copper
Alloys, Adolf Frei; Deformation, Recovery, Recrystallization, Martin Bauser
142 / Extrusion, Second Edition
metal specimens and suitable methods of etch- their orientation, which is usually completely
ing are used to reveal the structure—usually un- random.
der the microscope (Fig. 4.1). This is shown schematically in Fig. 4.3. The
The crystallites that form during solidification different types of metal lattices have a signifi-
from the melt change during the cooling. They cant effect on their behavior during deformation.
are stretched by the deformation and reform by The most important lattice structures are shown
recrystallization after annealing a deformed ma- in Fig. 4.4. They are face-centered cubic (fcc),
terial. They are, however, always crystallites body-centered cubic (bcc), hexagonal, and
with an ordered lattice structure that constitute body-centered tetragonal lattices. Figure 4.4 also
the metal. shows the lattice structure of the important met-
If a metal consists of only one type of crys- als at room temperature.
tallite, it has a single-phase structure.
The regular arrangement of the atoms of each
crystallite forms the lattice structure. The small-
est component of this lattice is referred to as the
unit cell. A real crystallite, also called a grain,
consists of many unit cells arranged uniformly
in adjacent rows like building blocks.
The unit cells are very small. The edge length,
known as the lattice constant, is of the order of
10ⳮ7 mm so that a crystallite with a mean di-
ameter of 0.1 mm contains 1018 elementary lat-
tice building blocks.
The location of a lattice—a simple cubic lat-
tice is shown in Fig. 4.2—is defined by the di-
rection of the edges of the elementary cell. This
is referred to as the orientation of the lattice.
In a real metal body consisting of numerous
crystallites, the latter can be differentiated by Fig. 4.2 Elementary cell in a simple cubic lattice [Sch 81]
Chapter 4: Metallurgical Principles / 143
Fig. 4.4 The most important types of metal lattice structures [Wie 86]
144 / Extrusion, Second Edition
Slip plane
Dislocation line
Dislocation line
(a) (b)
Fig. 4.6 Dislocation ⳱ linear lattice defect. (a) Edge dislocation. (b) Screw dislocation [Wie 86]
Chapter 4: Metallurgical Principles / 145
Fig. 4.7 Grain boundary structure. (a) Low angle boundary. (b) High angle boundary [Alt 94, Sch 81]
gives the amount of the two atoms (in weight the full range of solution up to the pure metal B.
percent) and the temperature is plotted along the The atoms B replace to an increasing extent the
ordinate. atoms A in their lattice positions. This is referred
Figure 4.9 shows schematically some of the to as atoms B dissolving in lattice A, analogous
frequently occurring basic types of binary phase to the processes in liquids. The solution of one
systems. The equilibrium diagrams of most bi- atom type in another is favored where the atom
nary systems can be constructed from these ex- radii differ only slightly from each other, e.g.,
amples. copper and nickel, which therefore form a con-
The liquidus temperature (at which solidifi- tinuous solid solution.
cation commences during cooling from the melt) In field a the metal occurs as a liquid, in field
and the solidus temperature (at which solidifi- b both as solidified particles and as liquid, and
cation is complete) can be read as well as the in field c as 100% solidified solid-solution for-
occurrence of the phases and the melting interval mat.
(the temperature difference between the liquidus
Because both metals usually have different
and the solidus temperature). In the melting in-
terval, solidified particles float in the melt. melting temperatures, the liquidus and the soli-
In pure metals, the liquidus and solidus co- dus temperature vary with the alloy addition.
incide because there is only one solidification Eutectic System (Type 2). In this case, the
temperature. It is identical to the melting tem- atoms of type B are completely insoluble in the
perature as the solid metal transforms to the liq- atoms of type A—usually when there are very
uid state at the same temperature on heating. large differences between the atom radii. If B is
The different basic types of the equilibrium alloyed to A, then B forms its own second phase.
diagram are shown in Fig. 4.9. The fraction of phase B increases in the equilib-
Continuous Solid Solution (Type 1). The rium diagram uniformly to the right and the frac-
lattice type of the parent metal A is retained over tion of phase A decreases accordingly. In the
146 / Extrusion, Second Edition
eutectic system there is one concentration E ical eutectic structure forms at this concentration
where the liquidus and the solidus temperature during solidification, usually consisting of alter-
coincide at the minimum melting point. A typ- nating layers of atom A and atom B. If, on the
other hand, an alloy outside the eutectic concen-
tration on the A-rich side cools, the A phase first
solidifies from the melt when the liquidus line
is crossed. The residual melt from which the
metal A is removed increases in concentration
in the metal B as cooling continues. At the eu-
tectic temperature the residual melt has reached
the eutectic composition and solidifies entirely
eutectically. The structure shows the primary so-
lidified grains of type A surrounded by the eu-
tectoid from the residual melt.
Eutectic System with Solid Solution (Type
3). This type of binary system occurs frequently
when the atoms of type B dissolve in small con-
centrations by substitution of atoms A in the lat-
tice (field c). As soon as a limiting concentration
is reached, the internal stresses produced by the
inclusion of the second atom type B become so
high that the formation of a second phase be-
comes energetically more favorable (field d). As
mentioned previously, the structure always tries
to achieve the state of lowest energy.
The composition of the A-rich phase in field
d corresponds to the concentration on the left
boundary line to c, the composition of the B-
rich phase to the concentration of the right
boundary line c2 at the corresponding tempera-
ture. The more the displacement of the compo-
sition of the alloy from the left boundary line to
the right, the greater is the number of grains of
the B-rich phase and, correspondingly, the fewer
the grains of the A-rich phase in this two-phase
Fig. 4.8 Twinned grains and twin boundary field.
Fig. 4.9 Basic types of phase diagram. a, melt; b, melt Ⳮ solid crystals; c, solid solution (homogeneous); d, two different crystals
(heterogeneous); E, eutectic point; P, peritectic point [Wie 86]
Chapter 4: Metallurgical Principles / 147
In Fig. 4.10, the structures corresponding to ing temperature, which must result in the pre-
different compositions are sketched under the cipitation of particles of the second phase even
equilibrium diagram of such a eutectic system after solidification to maintain equilibrium (see
with solid solution formation: also Fig. 4.13, section 4.2.3).
This type of eutectic system equilibrium dia-
● Concentration ␣: Crystals of the phase c1 so- gram with solid-solution formation rarely rep-
lidify here, surrounded by layers of the
resents the real state of an alloy because the mo-
eutectoid E formed at the eutectic tempera-
bility of atoms decreases so strongly with
ture E.
decreasing temperature that the elimination of
● Concentration b (eutectic composition): The
the nonequilibrum state is possible only after a
structure consists only of the layers of the
long holding period, if at all.
eutectoid of the phases c1 and c2.
● Concentration c: Grains of phase c2 form ini-
The structural state at high temperatures can,
therefore, be “frozen” by quenching from this
tially and are surrounded by the eutectoid on
temperature so quickly that the atoms have no
further cooling.
time to form the room temperature configura-
As can be seen from the diagram, the solu- tion.
bility of the second atom type decreases in the Peritectic System (Type 4). A peritectic re-
solution regions (fields c1 and c2) with decreas- action occurs when the melt (field a) forms a
new solid phase with a primary precipitated agram. Two different depictions are used for
solid phase. The ␣ grains are then surrounded three-part systems (ternary systems), as shown
by a shell of the b phase. In the peritectic con- in Fig. 4.11:
centration point a peritectoid structure forms that ● Isothermal section: The diagram consists of
appears similar in micrographs to the eutectoid. an equilateral triangle representing the three
The development of the equilibrium state on fur- alloying partners. Each point within the tri-
ther cooling is very restricted and can be angle can be related to a specific concentra-
achieved only after long holding periods at the tion of the alloying elements A, B, C (in the
corresponding temperature. example point P: 35%A, 40%B, 25%C).
This type of diagram naturally shows the
4.2.2.2 Intermediate Phases state at a specific temperature. In order to
represent all phase states, therefore, it is nec-
A solid solution consists, as previously men-
essary to have numerous similar isothermal
tioned, of the parent metal with interstitial or
sections that are often depicted within each
substitutional foreign atoms that are distributed
other.
randomly or only slightly ordered. ● Quasi-binary section: The proportion of two
Intermediate phases occur when two or more
types of atoms are fixed (in the example
types of atom are bonded together in an ordered,
shown A:B ⳱ 3:2) and the phase states stud-
usually complex, structure. Intermediate phases
ied for increasing amounts of atom type C.
have little or no deformability and are very brit-
This diagram can be read in the same way
tle. as a binary system.
T1 = constant
S
B = 40%
35%A S 40%B
T1
%A
S S
S
Temperature, T
S
%C
S S
25%C P 25%C
A, B, C: alloy partner
solid-solution phases
S: melt
Fig. 4.11 Tertiary system representation. (a) Isothermal section (temperature T1 ⳱ constant). (b) Quasi-binary section (alloy com-
ponent B, e.g., 40%) [Ber 83]
Chapter 4: Metallurgical Principles / 149
a multiphase structure as well as the fraction of temperature dependent but is faster the greater
the phases in the structure change during heating the concentration difference between the two re-
or cooling. Atoms have to migrate from one gions that will be equalized by the diffusion pro-
phase to another to maintain the new equilibrium cess.
when the temperature changes. This diffusion A precipitation process occurs if a second
occurs by transposition processes, which, in the phase is formed in the solid state of a homoge-
case of substitution solid solutions, requires a neous alloy during cooling when the solvus line
large number of vacancies. The migrating for- is crossed. Nuclei first form and continue to
eign atom always moves to the nearest vacancy grow until phase equilibrium is reached. Typical
position (Fig. 4.12). examples are the age-hardening aluminum al-
The atoms of a crystal lattice are stationary loys (Fig. 4.13).
only at absolute zero. As the temperature in- If a single-phase region is rapidly cooled from
creases they oscillate more strongly about their the solid solution (e.g., the dashed line X2 in
location and can then more easily leave their po- Fig. 4.13), the foreign atoms initially are re-
sition. When changing places, the migrating tained in solution because they are practically
atom has to pass through a state of higher en- immobile at low temperatures. Only when aging
ergy, known as the activation energy Q, which occurs at a temperature that enables significant
is easier in the energy-rich state of a higher tem- diffusion to take place can nuclei of the second
perature: diffusion processes occur faster at phase form and grow.
higher temperatures than at lower. Because this process of solution treatment
In interstitial solid solutions the signifi- with quenching followed by aging is usually as-
cantly smaller foreign atoms (e.g., carbon or ni- sociated with an increase in strength, it is re-
trogen in iron) migrate from one interstitial lat- ferred to as “age hardening.”
tice place to the next without the assistance of Energy also has to be expended for the nucle-
vacancies. The diffusion activation energy is ation of precipitates, but this is usually lower at
lower than with substitution solid solutions. specific crystal defects or in a grain boundary
From diffusion laws, which also apply to than in the interior of the undistorted lattice.
gases and liquids, the rate of diffusion is not only With a low precipitation pressure—e.g., slow
a b c
Activated state
Activation energy
Energy state
Base state
a b c
Fig. 4.14 Time-temperature transformation (TTE) diagram. (a) Principle [Ber 83]. (b) Continuous TTE diagram for AlMgSi0.5. I, solid-
solution ␣ (B dissolved in A) in equilibrium; II, solid-solution ␣ (B still dissolved in A) in unstable state; III, second phase
b precipitates to an increasing state from the solid-solution ␣; IV, equilibrium between phases ␣ and b; V, frozen unstable state of the
␣ phase
152 / Extrusion, Second Edition
During this coagulation process, atoms mi- ture with the minimum segregation that solidi-
grate by diffusion from smaller to larger precip- fied from the bottom to the top rather than from
itates. The small precipitates gradually disappear the outside to the interior.
and only the large precipitates remain. Many The formation of the solid phase by cooling
small precipitates have a higher total of bound- of a melt takes place by nucleation and growth
ary surfaces between the phases than a few large when the liquids line has been crossed in a simi-
ones. Because these boundary surfaces are en- lar way to the precipitation of a second phase in
ergy rich coagulation reduces the energy levels. the solid state described previously. Nuclei first
The martensitic transformation is a special form where the melt is cooler, which is at the
type of phase transformation in which the atoms mold wall in the casting process. As the under-
adopt new positions without diffusion. This cooling of the melt increases the nucleation
movement takes place extremely quickly after work needed reduces so that the number of nu-
quenching and produces significant stresses be- clei increases and a finer structure is produced.
tween the old surrounding lattice and the new
martensitic structure that is usually needle or
plate shaped. The formation of martensite is
mainly known in the behavior of steels, but it
does occur in other materials, including ␣-b
brasses. Casting and Cast Structure,
4.2.4 Melting and Casting Processes Homogenizing of
The structure in the billet is very important Aluminum Alloys
for the extrusion process. It has a strong influ-
ence on the extrusion load, the maximum pos- Wolfgang Schneider*
sible extrusion temperature and speed, as well
as the structure and properties of the extruded
section.
The change from chill casting to continuous 4.3 Development of the Continuous
casting—now used for most metals—alone Cast Structure
brought a significant quality improvement. This
prevented the severe billet segregation associ- Figure 4.16 shows the development of the
ated with chill casting. The aim of numerous continuous cast structure in a simplified man-
developments in continuous casting initially ner. The heat extraction through the water-
concentrated on the production of a fine struc- cooled mold wall, also referred to as indirect
cooling, causes the solidification of the periph- ling influence, are the height of the effective
eral region, i.e., to the formation of the so- mold wall and the metal head in the mold, the
called peripheral shell. This shrinks away from shape of the metal feed into the mold, and the
the mold wall and forms an air gap between the direct cooling of the cast log. The direct cool-
cast surface and the mold wall. This air gap ing of the cast log is carried out by either
hinders further heat extraction, resulting in re- spray water or mist cooling so that the mold
heating of the peripheral shell up to tempera- has to have corresponding nozzles that will
tures in the solidification range; i.e., partial or produce these methods of cooling. In alumi-
even complete melting of the peripheral shell is num continuous casting mist cooling predom-
possible. Peripheral segregation can form dur- inates because aluminum has a high coefficient
ing the dwell time in the air gap region as a of thermal conductivity. In this case the appli-
result of the partial melting. The surface of the cation of a closed water mist below the mold
cast log is characterized by this and by the so- is sufficient for rapid cooling of the cast log,
lidification of the peripheral shell itself, particu- and the use of additional specific cooling zones
larly in the meniscus region. The cast log is not necessary.
finally emerges with the peripheral shell from The cooling of the cast log by direct cooling
the bottom of the mold and is hit by the cooling results in the development of stresses as a result
water flowing from the mold to complete solid- of the temperature gradient from the interior of
ification, referred to as direct cooling. This re- the cast log to the periphery; these can lead to the
sults in the formation of the cast grain and cell formation of hot or cold cracking, depending on
structure and, finally, the eutectic cast phases the alloy system. The hot cracks usually form in
on the grain and cell boundaries as well as a the center of extrusion billets. Cold cracks, on the
characteristic profile of the solidification front other hand, can occur over the full cross section.
across the cast log cross section, which is also Alloys of the type AlMgSi are sensitive to hot
known as the cast sump (Fig. 4.16). cracking, whereas cold cracks are more likely to
The formation of the structure of the cast develop in AlCuMg and AlZnMgCu alloys.
log is significantly influenced by the mold The formation of the continuous cast structure
technology. The parameters of mold technol- is influenced by the casting parameters as well
ogy, which can be assumed to have a control- as the mould technology. The most important are
154 / Extrusion, Second Edition
the casting speed, the volume of cooling water regation zones. This can be clearly seen in the
and the casting temperature or the temperature example in Fig. 4.17.
of the melt as it enters the mould. The casting The occurrence of peripheral segregations has
speed, in particular, is extremely important. Ac- to be considered in relationship to the solidifi-
curate selection of the casting speed and the cation of the peripheral shell. Peripheral segre-
mould wall height for the alloy composition is gation forms during the dwell of the peripheral
very important, for example, to avoid hot and shell in the air gap region. Transport of residual
cold cracking. melt regions enriched in the alloying elements
towards the surface of the cast log takes place.
4.3.1 Peripheral Shell and The main transport mechanism is the metallo-
static pressure of the melt before the peripheral
Peripheral Segregation
shell. This is referred to as air gap segregation.
The peripheral region of the cast log in the A further mechanism for the formation of pe-
form of a peripheral shell is of particular impor- ripheral segregation is the residual melt enriched
tance in the continuous casting process. Numer- with alloying elements overflowing the menis-
ous casting defects can occur within this periph- cus curvature of the peripheral shell. This is re-
eral shell, and these should not finish up in the ferred to as meniscus segregation. Both these
semifinished product during subsequent pro- segregation methods described are shown sche-
cessing of the cast log. Consequently, the extent matically in Fig. 4.18 [Bux 77].
and the cast structure of the peripheral shell are Various segregation formation shapes can be
important and have to be controlled by the cast- differentiated in peripheral segregation. Two ex-
ing technology to minimize the peripheral shell amples are shown in Fig. 4.19. The nature of the
thickness and defects. segregation depends on the alloy type but also
The extent of the peripheral zone is largely to some extent on the mold technology.
determined by the mold wall height and the alloy
composition [Scn 85]. The larger the solidifica- 4.3.2 Cast Log Surface
tion interval of the alloy being cast and the
higher the mold wall, the thicker is the periph- The surface structure of the cast log is largely
eral shell. In comparison, the casting parameters determined by the peripheral segregation.
exert only a small influence on the thickness of
the peripheral shell.
Billet edge
250 mm
The cast structure of the peripheral shell usu- 1 2 3 4 mm
ally consists of a fine and a coarse cellular re-
gion. The fine cellular zone solidifies in direct
contact with the mold wall, whereas the forma-
tion of the coarse cellular region can be attrib-
uted to the insulation effect of the formation of
the air gap already described.
The mechanical properties of the solidifying
peripheral zone tend toward low values. They
are influenced by the cast structure formation
and the temperature of the peripheral zone, in
Alloying element concentration
The different forms of peripheral segregation Cold shuts are one surface feature that is not
shown in Fig. 4.19 also result in correspondingly related to the peripheral segregation. An exam-
different cast log surfaces. Figure 4.20 shows ple is shown in Fig. 4.20. The formation of cold
examples of surfaces caused by different types shuts can be attributed to the freezing of the melt
of segregation. meniscus in contact with the mold wall followed
Fig. 4.19 Examples of types of peripheral segregation. (a) Sweating beads. (b) Lap segregations. Casting direction downward. The
width is approximately 0.75 mm
156 / Extrusion, Second Edition
cleation processes in the melt [Rei 80]. The most tion as shown in Fig. 4.23 for different billet
important constituent of the alloys is insoluble diameters [Bux 77a].
TiB2, which exists as fine particles and plays a There is a coarse cellular structure in the pe-
direct role in the nucleation processes. Alloy ad- ripheral region of the cast log. This is the region
ditions of 0.2 to 1.5 kg/t aluminum are needed of the peripheral shell. Next to this is a region
to obtain adequate grain refining depending on with a very fine cell structure. Toward the cen-
the alloy composition. ter of the cast log, the cell size increases, reach-
The majority of commercial wrought materi- ing the maximum in the center. It should also
als cast by the continuous casting process exhibit be recognized that the quantitative profile of the
a cellular to dendritic type of solidification [Fle cell size strongly depends on the diameter of
74]. This, in turn, determines the cast grain the cast log. This relationship can be explained
structure. Figure 4.22 shows an example of a using the diagram in Fig. 4.24 [Bux 77a].
cellular/dendritic solidified cast structure. The faster the corresponding volume element
The grain and cell boundaries of the cast of metal is transformed from the liquid to the
grains are lined with intermetallic phases that solid state, then the finer the cell structure. If it
occur as eutectics during the solidification. The remains too long in the partially solidified state
grain and cell structure is also characterized by between the liquidus and the solidus state,
grain segregations, i.e., by nonuniform distri- coarse cells form because these have a high “lo-
bution of alloying elements in the structure. cal solidification time” [Kat 67].
These grain segregations, which can be attrib- Figure 4.24 shows that the distance between
uted to nonequilibrium solidification with an en- the liquidus and solidus line varies across the
richment of the alloying elements from the grain cross section of the cast log. The distance is the
center to the grain boundary, can result in the greatest in the center of the log where the high-
formation of eutectic phases on the grain and est local solidification time occurs and, accord-
cell boundaries even in those alloy systems ingly, the maximum cell size forms. The cell
where they cannot occur according to the equi-
librium diagram.
The cell structure of a cast log should be fine
and uniform [Los 83]. This results in a corre-
sponding fine and uniform distribution of the
cast phases in the semifinished product after de-
formation of the structure. This requirement is
particularly important for semifinished products
that are given a surface treatment for decorative
applications. Variations in the cell size can pro-
duce a banded surface.
The cast cell structure of aluminum cast logs
exhibit a characteristic profile over the cross sec-
Mold
Liquid
Pasty
Cell size
Solid
D(x)
Thickness of D
in the pasty region x
Fig. 4.24 Relationship between the distance between the liquidus and the solidus line and the cell size across the billet cross
section [Bux 77a]
size minimum coincides with the contact point ing rate, secondary precipitates form in various
of the cast log direct cooling, because this is quantities and sizes from the ␣-solid solution as
where low local solidification times exist be- a result of decreasing solubility. The actual pre-
cause of the high solidification rates. Corre- cipitation state influences the extrudability of the
spondingly, the distance between the liquidus billets, as is well known from the AlMgSi alloys
and the solidus lines is smaller than in the log [Res 92]. If the cooling rate is too slow, coarse
center where the cooling conditions in contin- Mg2Si phases can preferentially form on grain
uous casting result in the lowest solidification and cell boundaries in the temperature range
rates. above 400 C. These coarse phases do not dis-
solve quickly enough in solution during heating
4.3.4 Homogenizing to the extrusion temperature and can melt during
extrusion if their melting point is exceeded dur-
The cast structure produced in continuous ing the extrusion process. The consequence is a
casting is neither the optimum for the subse- reduction in the extrudability of the billet be-
quent processing nor for any surface treatment cause surface defects can form on the section
of the semifinished product. As mentioned pre- even at lower extrusion speeds. Mg2Si phases
viously, there is marked grain segregation in the that precipitate at temperatures below 400 C are
continuous cast structure as well as a supersat- so fine they can redissolve even during short
uration of alloying elements. The volume frac- times at the extrusion temperature.
tion of eutectic precipitates is also increased. If the cooling rate from the homogenizing
Therefore, a homogenization treatment consist- temperature is too high, fewer and finer secon-
ing of high temperature annealing at tempera- dary precipitates form. This is the same as in-
tures between 450 and 600 C is carried out to creasing the content of dissolved silicon and
remove grain segregation and supersaturation. magnesium in the ␣-solid solution. This raises
The heating time at the homogenization tem- the initial extrusion pressure and reduces the ex-
perature depends on the cell size and the rate of trusion speed at a constant extrusion load. Figure
diffusion of the specific alloying constituents 4.25 shows the structure of cast logs of Al-
[Ake 90]. A fine cell structure is therefore ad- MgSi0.5 alloy before and after homogenization.
vantageous because the concentration equaliza- Figure 4.25(a) shows the cast state with needles
tion within a cell can occur more quickly be- of AlFeSi phases on the cell boundaries. Figure
cause the diffusion path is shorter. 4.25(b) shows the structure after a defined an-
The cooling of the logs from the homogeni- nealing and cooling. The precipitated secondary
zation temperature is also important in the ho- phases (Mg2Si) can be seen in the ␣-solid so-
mogenization process. Depending on the cool- lution.
Chapter 4: Metallurgical Principles / 159
Fig. 4.25 Cast structure of AlMgSi0.5 round billet as-cast and after homogenization. (a) As-cast. (b) Homogenized
According to the previous discussion, there- thus reduced and that from the water impinge-
fore, the homogenization including cooling ment directly below the casting mold increased
should be designed to give fast cooling to 400 (Fig. 4.27).
C to avoid the precipitation of coarse phases.
This should be followed by slow cooling to re-
duce the content of dissolved alloying constitu- 4.4 Segregation and Gas Porosity
ents [Ake 88].
The solidification in the mold is described
using a copper-tin alloy with 8% tin as an ex-
ample (Fig. 4.28). As soon as the liquidus line
(at point 1 in Fig. 4.28 at temperature T1) is
crossed, nuclei of the solid phase with compo-
Casting and Cast sition “a” grow. The residual melt is impover-
ished in copper atoms and enriched in tin at-
Structure of Copper Alloys oms. In the equilibrium state the last residue of
the residual melt at temperature T2 has the com-
Adolf Frei* position “b.” A fully solidified structure has
zones with large variations in composition, i.e.,
Similar to aluminum alloys, the crystal segregation, particularly with slow cooling.
growth is largely influenced by the temperature Specific crystallographic directions are char-
profile in the mold. The cast structure usually acterized by high rates of growth leading to
consists of a narrow very fine grain peripheral preferentially orientated columnar grains that
zone connected to a coarse globulitic or lamina suppress others and enable a cast structure to
structure extending to the core. Frequently, develop. Preferred growth direction is the rea-
some form of single crystal is found in the cen- son for the formation of fir tree dendrites seen,
ter of copper billets. for example, in cast iron alloys.
Figure 4.26(a) shows the typical structure of The numerous nuclei that form with rapid
a copper billet with a large columnar grain frac- cooling and simultaneously grow produce a fine
tion, and Fig. 4.26(b) shows a brass billet with distribution of residual melt constituents in the
a globulitic core. solid state, which ensures that the segregation
Direct cooling by water impingement is usu- is less severe and more finely distributed.
ally situated below a relatively short mold for In the solid state, there is both grain segre-
the continuous casting generally used today for gation, which is a variation in concentration in
the casting of copper alloys (see Chapter 6). and around the individual grains of the solidi-
The indirect cooling through the mold wall is fied structure, and billet segregation, which pro-
Fig. 4.26 Cast structure of copper alloys. (a) Copper billet. (b) Brass billet
duces differences between the billet periphery processes, there still exists the possibility of de-
and the core by the growth of a solidification fects. Billets with the optimum extrudability
front from the cold mold wall toward the inte- can be achieved only by careful control of the
rior of the billet. The core is richer in the sec- casting parameters.
ond (in the example the tin containing) phase The best billet quality would be obtained
corresponding to the phase diagram. with a flat solidification front perpendicular to
If gases are dissolved in a melt (e.g., N2 or the casting direction. This would require the en-
H2), their solubility in the solid state is usually tire heat extraction to take place in the direction
significantly lower than in the melt; i.e., the gas of the log axis. This can be achieved only with
precipitates in the form of pores during solidi- uneconomic casting speeds.
fication. In chill mold casting where the melt Practice is a long way removed from the
slowly grows from the periphery toward the ideal case because both indirect and direct cool-
center, these gas pores collect like pearl strings ing remove the heat from the cast log mainly
in the center of the cast billet. In continuous perpendicular to the axis. The casting sump (re-
casting they are found in the segregations of the gion of liquid metal in the cast log) has a U-
residual melt, i.e., in the boundaries of the or V-shaped section.
grains of the cast structure. As a rule of thumb, approximately one-third
Segregations are, as mentioned previously, of the heat to be extracted is taken through the
supersaturated zones outside the equilibrium mold and the rest by direct cooling of the cast
state of the solidified structure. The segrega- log.
tions solidified from the residual melt possess If the direct cooling of the log is not exactly
a composition that produces crystallites of brit- symmetrical, this results in distortion of the
tle phases, which hinder working. In addition, emerging log. This bending can quickly be-
because these segregation zones, which solidi- come so large that it makes direct extrusion
fied at lower temperatures, also melt at lower very difficult and indirect extrusion with its
temperatures than the parent metal during heat- longer billet lengths of up to 1.5 m impossible.
ing, there is a risk of grain-boundary melting
during hot working.
4.5.1 Cast Log Surface
4.5 Cooling and Casting Defects The appearance of the surface of the cast log
is largely determined by the processes in the
In spite of the indisputable advantages of mold. The melt transferred into the mold ini-
continuous casting compared with the older tially solidifies in direct contact with the mold
Chapter 4: Metallurgical Principles / 161
sidual melt, which solidifies last, being enriched Solidification with a V-shaped sump results
under the log surface and being partially pushed automatically in stresses in the cast log and, in
outward into the shrinkage gap. Good extrusion the worst case, can result in longitudinal cracks
results can be obtained with these billets only in the core of the cast log. With very sensitive
by turning off the tin-rich peripheral layer and materials such as aluminum containing special
homogenization. CuSn8 is homogenized at ap- brasses, these cracks can extend to the surface
proximately 700 C for several hours to dis- of the cast logs.
solve segregations of the brittle, tin-rich low- Unfortunately, it has to be assumed that such
melting-point d-phases. defects in the center of the billet along with the
The shrinkage gap is reduced in molds that surface defects do not weld together in the ex-
are tapered toward the bottom, and the effects trusion press but produce material separation in
described can at least be suppressed to some the extruded section and thus scrap.
degree. These molds are preferred for the cast- Exception: in the casting of copper billets
ing of copper. The taper has to be carefully with high casting speeds, shrinkage cracks can
matched to the casting speed and the cooling occur in the core along the grain boundaries
conditions. The optimization is helped by com- with limited longitudinal extension. These “spi-
puter programs. ders” disappear during extrusion and do not
If the metal head in the mold is not constant have any detrimental effect on the section.
during the casting, inclusions of the covering In the sections “Aluminum Alloys” and
agent and slag can occur under the surface of “Copper Alloys” in Chapter 6, detailed infor-
the cast log. mation on casting plants are given for the dif-
Excessive direct cooling can cause longitu- ferent materials.
dinal cracks in the surface of the cast log, par-
ticularly with stress-sensitive alloys.
When casting is carried out with a salt cover,
a thin salt film is initially formed on the surface
of the cast log, and this has to be rinsed off in
the region of direct cooling. If the composition Deformation, Recovery,
of the covering salt is unsuitable or the direct
cooling inadequate, the film can bond firmly to Recrystallization
the cast log. It can then act as a lubricant be-
tween the billet and the container during extru- Martin Bauser*
sion and result in parts of the cast skin flowing
into the extruded section, resulting in scrap due As well as the references given at the start of
to laminations. section 4.2, the following works are recom-
mended for a more detailed discussion of section
4.5.2 Interior of the Cast Log 4.3: [See 85, Haa 84].
Perfect results in extrusion can be achieved
only from billets with smooth, clean surfaces
and a dense structure over the complete cross 4.6 Deformation of Pure
section. Unsuitable casting conditions not only Metals at Room Temperature
produce defects on the surface of the extruded
section, but also within the section.
With a deep V-shaped casting sump there is 4.6.1 Dislocations
the risk that gas bubbles can no longer escape In section 4.2.1, dislocations are described as
but are retained in the region of the solidifica- linear defects in the crystal lattice as shown in
tion point: porosity in the cast. In the region of Fig. 4.6. In real lattices, they form networks and
the sump tip small zones of liquid metal can are unevenly distributed (Fig. 4.29).
also be cut from the casting sump. When they If an external force is applied, a crystal lattice
solidify, the shrinkage results in small hollow initially deforms elastically following Hook’s
spaces—solidification blowholes. law. The elastic deformation is reversible—i.e.,
Fig. 4.30 Lattice structure during deformation. (a) Elastic deformation. (b) Plastic deformation
a b c
Force
Slip
plane
Slip step
Force
Dislocation
As slip continues the crystal rotates (Fig. Strengthening means that dislocation movement
4.37). More and more slip systems then move is made more difficult by these and other barriers
into the 45 region and are activated (multiple during the deformation.
slip).
In these additional slip systems, the disloca-
tions that move have to cross the original ones 4.6.3 Polycrystals
and are trapped by them. These locations form A polycrystal can be considered to consist of
defects at which following dislocations pile up. several single crystals of different orientations.
Chapter 4: Metallurgical Principles / 165
Plane (111)
(4 possible planes)
Direction [110]
(3 in a plane)
Slip system (111)[110]
Plane (0001)
Plane (1010)
(3 possible planes)
Each single crystal will deform as discussed slip systems have to be active in each grain,
above in its principle slip system. The bound- which contributes to the strengthening.
aries with the neighboring crystal, however, Whereas in single crystals dislocation lines
hinder this free movement. can disappear at the surface, they pile up at grain
In order to retain the cohesion between the boundaries in polycrystals. If no grain boundary
individual deforming crystallites, at least five slip occurs, then the higher the number of grain
166 / Extrusion, Second Edition
Fig. 4.39 Interaction of dislocations and particles [Ber 83]. (a) Intersection of “soft” particles. (b) Bypassing of “hard particles”
Chapter 4: Metallurgical Principles / 169
400
350
Rp 0.2, MPa
300 Overaging
250
Fig. 4.40 Yield stress of age-hardening aluminum alloy as a function of the aging time [Blu 93]
170 / Extrusion, Second Edition
Dislocation
Dislocation rich lattice
free lattice (work hardened)
(recrystallized)
Grain
boundary
1.0
Recrystallized fraction X
0.8
0.6
350 °C
0.4
0.2
Time, s
Fig. 4.44 Variation with time of recrystallization (Al99.5 after 5.1% tensile deformation) [And 48]
The rate of migration of the new grain bound- aluminum, it can even be completely suppressed
aries and thus the rate of recrystallization is the by recovery—at low heat treatment tempera-
greater the larger the preceding deformation and tures and small deformation.
thus the larger the energy stored in the deformed The recrystallization temperature above
structure. Naturally, a higher temperature pro- which recrystallization can be expected is usu-
motes the grain-boundary migration and in- ally related to the melting point of a metal:
creases the rate of recrystallization.
Recovery preceding recrystallization, e.g., at
Trecr 艑 0.6 • Ts[K]
low heat treatment temperatures, that has re-
duced the deformation energy stored in lattice
by sub grain formation hinders recrystallization. This recrystallization temperature should not be
In metals with high stacking fault energies like considered unequivocal.
172 / Extrusion, Second Edition
With deformed brass CuZn37, for example, getically more favorable positions during the de-
the softening from recrystallization after high formation by cross slip and climb. This means
deformation starts at 400 C but only at 500 C that recovery processes can proceed with the for-
after low deformation. With pure aluminum after mation of a substructure during the work-hard-
98% deformation recrystallization commences ening—and not only after heat treatment follow-
at 300 C and at 400 C after 20% deformation ing cold working [Mug 84]. This is called
[Alt 94].It is, therefore, more correct to refer to dynamic recovery.
a recrystallization interval instead of a recrys- If deformation is carried out quickly enough
tallization temperature. at a high temperature, the work hardening can
If a structure textured by deformation is given be so high despite the start of recovery that re-
a recrystallization heat treatment, the new struc- crystallization can take place even during the de-
ture can also exhibit preferred orientation, a so- formation—this process is frequently observed
called recrystallization texture. One cause can be in the extrusion of specific materials. It is re-
that grains of a specific orientation in the de- ferred to as dynamic recrystallization [Got 84].
formed structure are less deformed than others. The stacking fault energy plays an important
Nuclei of preferred orientation then grow from role in the boundary between recovery and re-
them into the severely deformed grains. crystallization during hot working.
Deformation and recrystallization textures are High stacking fault energies and thus fewer
closely related to each other but usually differ. divided dislocations occur in bcc alloys (e.g., ␣-
Recrystallization textures are also characteristic iron, b-brass) as well as in certain fcc alloys
for the deformation process and for the relevant (e.g., aluminum). In these cases, the cross slip
lattice structure (e.g., AlCuMg [Moc 75]). and climb needed for subgrain formation and re-
covery is easier—recovery is more likely to take
4.8.2 Deformation of Pure place in these cases in preference to recrystalli-
Metals at High Temperatures zation during hot working. Low stacking fault
energies associated with large divided disloca-
If a pure metal is deformed at a higher tem- tions are found with a few other fcc lattices (e.g.,
perature, both the yield stress and the work hard- copper and copper alloys). In these cases, recov-
ening are reduced (Fig. 4.45). ery is more difficult, and dynamic recrystalli-
As the temperature increases, the dislocations zation processes simplified during hot working.
can start to migrate through their slip systems at The strength reducing recovery and recrystal-
lower shear stresses due to thermal activation, lization processes during hot working can take
which reduces the yield stress. The work hard- place so quickly after reaching a specific work
ening—that is, the gradient of the strength hardening that there is equilibrium between soft-
curve—is reduced because the vacancy diffu- ening and work hardening and the hardening
sion at higher temperatures is also eased and curve remains horizontal (static case). Naturally,
hence piled up dislocations can move to ener- the dynamic recovery processes also result in a
delay in the fracture-initiating mechanisms (see
section 4.11), and the elongation to failure in
25
838 K
tensile tests increases with increasing tempera-
ture.
If the events occurring within the structure in
Shear stress, MPa
20
hot working are studied, it is clear that these pro-
15 943 K cesses depend not only on the temperature but
also on the rate of deformation.
1033 K The slower the deformation rate, the greater
10
is the time for the recovery and recrystallization
1103 K
processes to counteract the work hardening from
5 the multiplication and piling up of dislocations.
1273 K
The work-hardening curve is, therefore, flatter
0 and its horizontal leg lower the slower the de-
0 0.25 0.5 0.75 1.0
formation rate. At a fast rate of deformation, a
Strain relatively high flow stress has to be expected.
Fig. 4.45 Work-hardening curves of copper single crystals This explains the high dependence of the defor-
as a function of temperature [Got 84] mation resistance on the rate of deformation in
Chapter 4: Metallurgical Principles / 173
Stress, MPa
ditional Information 3,” in this chapter.
The stress-strain curves obtained from torsion
50
tests cover a much larger strain to failure than
tensile tests because of the largely tensile-stress-
free deformation.
They are therefore more suitable for assessing
0
the behavior of metals in practical hot working, 1 2 3
in particular extrusion, which also does not in-
Elongation, %
volve any tensile stress (Fig. 4.47) [Fie 57, Ake
66]. Fig. 4.46 Strain-rate dependence in hot working (stress-
The hot stress-strain curves obtained from tor- strain curves of nickel) [San 75]
sion tests exhibit after the initial increase, in
which the number of dislocations and the inter-
nal stresses increase significantly, a large sta- If the second phase exists in the form of fine
tionary region with hardly any additional work precipitates (in the range of 0.04–0.4 lm diam),
hardening. The work-hardening and recovery these also tend to retard recrystallization because
processes are in balance. The stress-strain curve they can exert a significant resistance to the nec-
starts to fall only when structural defects result essary migration of grain boundaries, particu-
in fracture. larly where they accumulate. This can occur to
Usually, no recrystallization occurs during the such an extent that at a moderate annealing tem-
hot deformation of aluminum and many of its perature recrystallization can be completely sup-
alloys. Subgrains are more likely to develop by pressed and only recovery takes place. The
recovery and their shape and size hardly change strength then does not fall completely during an-
during the stationary region. If the load is re- nealing and the deformation texture remains.
moved and the temperature maintained or slow With two-phase alloys with large crystallites
cooling permitted, recrystallization can occur— of the second phase, it is possible that only one
delayed significantly by the low internal energy. phase with a low recrystallization temperature
One example is the recrystallization during ex- recrystallizes during the annealing process,
trusion of low-alloyed aluminum alloys after whereas the second phase remains unrecrystal-
leaving the die [McQ 90]. lized.
Still more complicated is the case when a de-
formed alloy is in thermal unequilibrium during
4.9 Alloys at Higher Temperatures annealing. Softening processes then occur by re-
covery and recrystallization simultaneously with
precipitation processes (or, in rare cases, disso-
4.9.1 Annealing of Alloys
lution processes) of second phases [McQ 90,
In the annealing of deformed alloys—from McQ 90a]. The dependence of the mechanical
the point of view of the deformation energy—in properties on the annealing conditions is there-
which there is thermal equilibrium at the an- fore complicated and difficult to explain.
nealing temperature, recovery and recrystalli- There are more vacancies in deformed metals
zation processes play the main role as with pure than in undeformed metals, which simplifies the
metals. However, with single-phase alloys, the diffusion of foreign atoms to precipitates. There-
thermal activation of the climb and cross slip fore, the precipitation processes during anneal-
processes initiating thermal activation is more ing take place more quickly in the deformed
difficult because of the presence of foreign at- structure than in the undeformed state.
oms. This also applies to the migration of grain It is possible today to construct high-strength
boundaries during recrystallization because materials in which specific alloy composition,
grain boundaries are frequently enriched with heat treatment and deformation precipitation
dissolved atoms and have to be torn away from hardening and work hardening are combined
them. without any significant softening processes tak-
174 / Extrusion, Second Edition
d /dt = 3s–1
200
600 °C
200 °C
300
300 °C 700 °C
200 100
400 °C 750 °C
800 °C
100 850 °C
500 °C
600 °C
700 °C
0
0
0 10 20 30 40 50 60 70 80 0 0.5 1.0
Elongation , % Log strain
(a) (b) g
Fig. 4.47 Hot low curves for CuZn8 obtained from different methods. (a) Hot-tensile tests. (b) Torsion tests [Bau 63, DGM 78]
ing place during the permitted time at the in- 4.10 Processes in Extrusion
tended working temperature [Ber 83].
Billet heating before extrusion cannot be con-
4.9.2 Deformation of Alloys sidered to be independent of the previous hot
at Higher Temperatures processes—casting, hot forging, or homogeni-
zation. In addition, the temperature and time of
In single-phase alloys, the embedded foreign
heating are determined by various, often con-
atoms hinder the migration of dislocations as in
flicting, requirements:
cold working but also impair dynamic recovery
and recrystallization. The hot yield stress, work ● Low extrusion pressure
hardening, and hot strength increase with in- ● High extrusion speed
creasing foreign atom content (Fig. 4.48). ● Limitation of the exit temperature to a max-
Precipitates, which retard static recrystalliza- imum (surface quality) and to a minimum
tion, also naturally hinder dynamic recrystalli- (recrystallization, with aluminum alloys so-
zation processes. Hot-strength curves are there- lution heat treatment during extrusion).
fore steeper with alloys with precipitates and
attain the stationary (horizontal) state later or at When determining the preheat temperature,
a higher temperature. the deformation heat during extrusion (increas-
The high hot strength of high-alloy materials ing the extrusion temperature) and the heat flow
naturally makes hot working more difficult and into the tooling (reducing the extrusion tem-
thus materials “more difficult to extrude.” perature) have to be taken into account.
Because, as described above, a high vacancy If nonhomogenized billets of age-hardening
concentration accelerates the process of precipi- alloys are used, the homogenizing effect during
tation processes, the rate of precipitation in- billet heating increases the longer it lasts. In this
creases during the hot working of an alloy not case, slower gas furnace heating is more effec-
in equilibrium. tive than fast induction heating. Not only can
The factors that determine whether and at segregations harmful to extrusion be reduced,
what rate recovery and recrystallization takes but also precipitates dissolved and supersatura-
place during hot working are the same as those tions reduced.
governing annealing after previous cold work- In contrast, previously homogenized billets of
ing. suitable aluminum alloys cooled to a specified
Chapter 4: Metallurgical Principles / 175
Fig. 4.50 Dynamic recovery and recrystallization processes in extrusion. (a) High stacking fault energy. (b) Low stacking fault
energy [McQ 75]
If the fibers with higher deformation (e.g., the transverse direction. This is referred to as the
close to the surface of the extruded section) are extrusion effect.
very elongated and thin (width approximately Recrystallization retarding additions in suit-
two subgrains), adjacent grains can grow to- able aluminum alloys can, however, precipitate
gether and the fibers appear shorter [McQ 90]. coarsely during annealing at high temperatures
The grain structure, however, is so severely (defective homogenization, billet heating in a
distorted in the shear zones that no grain bound- gas furnace). A second phase that has no effect
aries are visible under the microscope and the on the recrystallization then forms (e.g., man-
precipitates present are randomly distributed. ganese in AlMgSi). Then the aluminum material
AlMgSi0.5 sections recrystallize with fine grains can, as described earlier for AlMgSi0.5, fully
but only after leaving the die (static and not dy- recrystallize after leaving the die—while the
namic). section is still hot.
In alloys with recrystallization retarding ad- In the production of aluminum sections with
ditions (e.g., AlMgSi or AlCuMg with additions a decorative surface, structural variations and
of Mn, Cr, or Zr), the recrystallization tempera- textures can produce flecks and stripes. Because
ture is raised to such a level that no recrystalli- only the zone immediately below the surface of
zation occurs even after leaving the deformation the section plays a role, attention has to be paid
zone (particularly following rapid cooling). not only to the billet production (see section
However, subsequent solution heat treatment 4.2.4) but also to the die design. The procedures
reveals that the peripheral zone from the shear that have to be taken into account in the manu-
zone is more heavily deformed than the core facture of aluminum sections are described in
and, therefore, statically recrystallizes, often detail in the section “Extrusion of Semifinished
with very coarse grains, whereas the more Products in Aluminum Alloys” in Chapter 5.
weakly deformed core remains unrecrystallized. Independent of the material, in extrusion
The unrecrystallized structures usually have a without lubrication the zones close to the surface
strong texture because of the high deformation of the extruded zone are hotter than the core be-
in the extrusion press, whereby the strength in cause of the concentration of the deformation in
the longitudinal direction is much higher than in the shear zone and the friction between the die
Chapter 4: Metallurgical Principles / 177
land and the material. However, at the surface dependent on the deformation conditions. For
this friction also produces tensile stresses as the example, in a tensile test the toughness defining
core of the extrusion accelerates. It is therefore elongation to fracture is relatively low, but in the
no surprise that the billets with residual melt torsion test in which the deforming elements are
segregations with low melting points produce subjected to other forces, it can be higher. In
crack-sensitive extrusions. If these segregations particular, in extrusion with its high hydrostatic
are not previously eliminated by homogeniza- contribution to the deforming loads much higher
tion, the only option is to extrude at low tem- deformations can be achieved than in the simple
peratures and slow speeds. This prevents the tensile test. The phenomena occurring in the ten-
temperature of the section surface from reaching sile test up to fracture should be understood (Fig.
the dangerous region of melting, which results 4.51). A more detailed explanation is found in
in transverse cracks (see the section “Extrusion [Rie 87].
of Semifinished Products in Copper Alloys,”
Fig. 5.45, in Chapter 5). 4.11.1 Ductile Fracture
In the extrusion of copper alloys and steels, In metal working the most common type of
spontaneous recrystallization usually takes place failure is ductile fracture following deformation.
during the deformation as the extrusion tem- As a rule, the deformed metal is not defect free.
perature is well above the recrystallization tem- During the deformation in the tensile test, ini-
perature (which is 0.8–0.9 times the melting tially small voids form at internal boundary sur-
point TS). It can happen that the start of extru- faces with low adhesion, e.g., at inclusions,
sion, where the deformation is low and the tem- coarse precipitates or at existing gas pores,
perature high, has a coarse secondary recrystal- where the stress concentration becomes high
lized structure, but the end of extrusion—where enough during the working. Only very pure met-
the deformation is high and the exit temperature als deform in tensile tests without this void for-
lower due to cooling during extrusion—is fine mation.
grained. The cross section of the tensile specimen in
In pure (and low-alloyed) copper so few re- the region of the voids is reduced. The tensile
crystallization retarding precipitates are present force therefore exerts a higher stress, which
that the grain boundaries migrate relatively eas- leads to higher elongation in this zone, resulting
ily. After the primary recrystallization in the de- in a localized necking. Once the necking has
formation zone, a secondary coarse recrystalli- started this area continues to reduce in cross sec-
zation has to be expected in the emerging tion as the stress increases, whereas the sections
extrusion (at 800–900 C). Rapid cooling is used of the specimen that have not necked elongate
directly behind the die to prevent this. only slightly. Soon the pores in the necked zone
increase in size and grow together until fracture
occurs between them. The fracture surfaces are
4.11 Toughness, Fracture rough and consist of craterlike depressions, each
corresponding to an original void. The ductile
The toughness of a material is—for the same fracture usually passes through the grains and is
temperature and the same deformation rate— therefore transcrystalline.
Fig. 4.51 Different failure methods (in tensile testing) [Ash 79]
178 / Extrusion, Second Edition
At higher temperatures, as discussed previ- If the deformation is carried out at such a high
ously, the yield stress and the work hardening temperature that existing segregations start to
are reduced by the onset of the recovery pro- melt, an almost completely brittle fracture oc-
cesses. This means that the stress needed to nu- curs.
cleate the voids, e.g., at inclusions, is first
reached after a higher deformation. The elon-
gation to fracture can then increase. 4.11.3 Fracture during Hot-Working
However, at higher temperatures the flow The processes leading to fracture are now ex-
stress and the work hardening react more sen- plained using hot torsion tests. Torsion tests cor-
sitively to the deformation rate, and accordingly respond more closely to the processes in extru-
the fracture behavior varies at higher speeds. As sion, but only a few suitable measured results
a rule, the elongation to fracture decreases as the are available.
rate of deformation increases. Elongation and necking traverse in hot-tor-
Grain-boundary decoration by foreign atoms sion tests one or two minima. The examples of
or inclusions and thin films of segregations can E-copper and of phosphorous containing tin
weaken the grain boundaries at high tempera- bronze illustrate this (Fig. 4.52). With E-copper
tures to such an extent that the crack propagates (Fig. 4.52a), the elongation to fracture and the
in an intercrystalline manner. necking initially reduce with increasing tem-
perature (up to a minimum of approximately 500
C) and then increase. As the temperature in-
4.11.2 Brittle Fracture and Mixed Types
creases, severe grain-boundary cracks form per-
Pure deformation-free brittle fracture is rare; pendicular to the tensile direction. They form
more common is low-deformation brittle frac- and grow by the migration of vacancies to the
ture. Neither of these fracture types occurs dur- grain boundaries associated ultimately with
ing extrusion. Their explanation does, however, weakening due to grain-boundary accumulation.
increase the understanding of the possible frac- Above the minimum temperature, where the
ture processes. elongation to fracture increases again, the pro-
At sufficiently low temperatures most metals cesses of recovery and, in particular, recrystal-
fail without or with only slight deformation by lization occur. Existing voids are dissolved and
brittle fracture. The starting point is a crack that the susceptibility to fracture reduced.
is already present or forms after slight plastic A second minimum similar to that seen with
deformation. The tip of this crack acts as a 8% tin bronze (Fig. 4.52b) can be related to the
notch; i.e., a high stress concentrates here under effect of segregations that have a high mobility
a tensile load, which, when the so-called crack and readily melt [Bau 63]. In the example of the
propagation stress is exceeded, results in a de- tin bronze it is a low melting point phosphorus
formation free or low deformation cleavage containing phase on the grain boundaries.
fracture. The fracture surfaces are smooth.
With increasing temperature, the stress peak
that forms at the initial crack under load is re- 4.11.4 Defects in Extrusion
duced by local deformation so that the crack Tensile stresses are usually required for crack
propagation stress is reached only after higher formation and propagation. High shear stresses
work hardening, in other words, higher plastic can also result in cracks—referred to as shear
deformation. The tendency to brittle fracture re- cracks.
duces with increasing temperature or disappears In extrusion, the material in the die defor-
completely. mation zone is under three-dimensional com-
The cleavage fracture propagates along sur- pression. Only when it has passed through the
faces with low cohesion. If these are specific die will the tensile stress developed close to the
crystallographic planes, then the fracture is surface by the friction on the die bearing have
transcrystalline. With weakened grain bound- an effect. The magnitude of this tensile stress
aries attributed to higher temperatures or accu- depends on the friction and the die design. In
mulated foreign atoms, segregations, or precip- lubricated extrusion (glass lubrication with steel
itations the fracture propagates between the and nickel alloys, hydrostatic extrusion) it is
grains and is thus intercrystalline. Frequently, a lower than in unlubricated (aluminum) or if only
fracture shows both transcrystalline and inter- a flat die is lubricated (copper). The tensile
crystalline components. stresses at the surface of the extruded section
Chapter 4: Metallurgical Principles / 179
400
Tensile strength, MPa
300
Tensile strength
200
Yield stress
Yield stress
100
0
100
80
Elongation to fracture
60
40
20
0
0 100 200 300 400 500 600 700
500
Tensile strength, MPa
400
Tensile strength
300
Yield stress
Yield stress
200
100
0
80
Elongation to fracture
60
40
20
0
0 100 200 300 400 500 600 700
combined with the temperature increase in the At a small extrusion ratio the core accelerates
peripheral zone result in transverse cracks (fir so quickly during extrusion relative to the sur-
tree defect) if an existing grain-boundary accu- face zone that the shear stresses are sufficient to
mulation is severely weakened or even melted. separate a surface shell from the core. This also
Under the microscope these grain-boundary ac- requires correspondingly weakened zones.
cumulations can be detected along with the pre- With very small extrusion ratios, conical-
dominantly intercrystalline nature of the cracks shaped transverse cracks can develop because
(Fig. 4.53). tensile stresses can occur along the billet axis
Internal cracks in tubes have the same origin: before the die plane. These can result in voids
if the friction between the material and the man- and cracks at the affected areas.
drel is high enough at the extrusion temperature Both types of defects—the peeling of a sur-
to destroy the cohesion between grain bound- face shell from the core and the core cracking—
aries transverse to the direction of extrusion, cannot be detected on the surface. Materials at
transverse cracks will form on the internal sur- risk must be tested using nondestructive meth-
face of the tube. ods when necessary.
180 / Extrusion, Second Edition
4.12 Solid-State Bonding fied, atoms changing places with each other can
fit with the opposing lattice so well that the bond
Materials can bond together under pressure between the atoms at the boundary surface is
and at an elevated temperature without macro- optimized. There are hypotheses that the dislo-
scopic shape changes (diffusion bonding). How- cations stacked together by pressure welding can
ever, at least one of the bonding partners has to traverse the boundary surface into the other part-
undergo a significant compressive deformation ner.
(compression, rolling, extrusion). Any existing coatings, e.g., fine oxide skins
The bonding processes that occur during de- or films of lubricant, hinder any adhesive bond.
formation is the reason for the use of the extru- If the areas of the components being bonded are
sion process in many cases. increased during the bonding process, e.g., in
The weld seams in hollow profiles, the pro- roll cladding or extrusion, brittle coatings such
duction of composite profiles and the processing as oxides cannot follow this expansion. Instead,
of composite materials as well as the extrusion they break up into individual pieces. Fresh metal
of metal powders are discussed in this section. forms between the pieces on the surface and this
can now bond with the opposite side. Pressure
4.12.1 Bonding Processes welding requires both high pressure and a large
The most common methods of joining two deformation and thus an increase in the surface
components are welding and soldering. In both area. Since, in roll cladding and extrusion
cases the liquid phase takes the dominant role. through a hollow section die there is also rele-
In welding, the boundary layer between the vant movement between the two partners and
components melts. The resolidified melt forms frequently polyganization or even recrystalliza-
the “weld seam.” In soldering, both the parts re- tion occurs by recovery processes the grains or-
main in the solid state, only the solder between ientate themselves into matching positions. If
them melts and solidifies. The joint is formed by the bond is very good, it is impossible to detect
adhesion and diffusion at the boundary surface. the joint under the microscope (see Fig. 4.55).
When bonding in the solid state—referred to If the surface coating can follow the increase
as pressure welding—the formation of a liquid in the contacting areas, i.e., smear, then bonding
phase usually is not required. The most common is not possible during the contacting process.
methods are roll cladding, friction welding, and One example is the damaging effect of lubricant
ultrasonic welding (more information on pres- in the extrusion of hollow aluminum alloy sec-
sure welding is found in [Tyl 68]. tions. This can prevent the formation of a sound
If two metallic surfaces meet, they can bond pressure weld.
together if the surface atoms of both components
are approximately a lattice spacing apart. The 4.12.2 The Formation of Pressure
faces then act as a grain boundary and the me- Welds in Hollow Sections and
tallic bonding forces of the electron gases act during Billet-on-Billet Extrusion
across the boundary surfaces. Experience shows
that this adhesion process rarely occurs without If hollow sections are produced using bridge
the contribution of pressure and temperature. or porthole dies as described in Chapter 5, in the
Absolutely flat and clean boundary surfaces are section on the extrusion of aluminum alloys, the
required and it is made easier or possible at all divided strands bond together in the welding
if the two components pressed together have chamber immediately in front of the die into two
identical, or similar, lattice structures. or more longitudinal seams. These are not welds,
A higher surface pressure always flattens very as sometimes stated, but metallic bonds from
small irregularities and improves by plastic de- solid-state adhesion. In these die zones, which
formation of the roughness peaks the contact be- are more correctly referred to as bonding cham-
tween the components pressed together over the bers, the high transverse forces—almost equal
maximum contact area. With pure aluminum the to the hydrostatic pressure in the undeformed
pressure welding commences after only 10% de- billet—act on the surfaces of the divided strands
formation of the two surface areas; however, it producing an increase in the surface area by the
is only after 70% that the tear resistance of the reduction of the cross section in the chamber.
joint matches the value of the parent metal. The adiabatic heating from the deformation also
At a higher temperature, this flattening and plays a role. The strands that are separated just
smearing together of the two surfaces is simpli- prior to the bonding—and with the exclusion of
Chapter 4: Metallurgical Principles / 181
Fig. 4.54 Breakup of the surface layer in longitudinal welds in the production of aluminum hollow sections. (a) Meeting under the
leg. (b) Breaking apart. (c) Clean longitudinal weld [Ake 92]
air—are free of any oxide or lubricant surface degree of deformation required to produce suf-
coating, assuming a clean die is used, that would ficient pressure in the bonding chamber is not
hinder the bonding. reached and the use of hollow section dies made
Oxide is brought into the welding chambers difficult or even impossible. Finally, with ma-
of the die only during the first filling when the terials that do not recrystallize at the extrusion
free oxide coated end faces come together (Fig. temperature, there is no possibility of healing the
4.54a) [Ake 92]. The fractured remains of the voids in the bonds by recrystallization [Ake
oxide surface are mostly carried away with the 92a].
first part of the section (Fig. 4.54b). The subse- There are, however, cases where defects in the
quent bonding takes place between material re- bonds occur even with materials well suited for
gions that have initially been compressed in hollow section extrusion. These problems are
front of the legs of the mandrel and have then discussed in more detail in Chapter 5.
flowed with extreme shearing along the flanks With copper and brass, which are extruded in
of the leg and combined at the dead metal zones the temperature range 600 to 900C, the danger
beneath the legs. The strands that come together of separating oxides flowing in is greater than
are free of any oxide film. The process of weld- with aluminum alloys. This is one of the reasons
ing then consists merely of the initially small why extrusion of these materials through hollow
contact surfaces being extended over the entire section dies is usually avoided (see Chapter 7,
length of the section and thus being increased the section on tooling for copper alloys).
by several orders of magnitude. Subgrains then The ability of aluminum alloys to bond by
form continuously even over the original contact pressure welding is not only utilized in the pro-
surfaces. This repolygonization is linked to the duction of hollow sections but also in billet-on-
movement of dislocations but does not require
any atom diffusion.
In addition, the material recrystallizes usually
in the deformation zone (e.g., copper) or im-
mediately on leaving the die (e.g., AlMgSi0.5)
so that the newly formed grains grow away from
the contact faces freshly bonded by adhesion and
heal them.
The contact faces that equate to a severely
distorted grain boundary disappear during this
recrystallization and cannot be identified under
the microscope (Fig. 4.55).
The suitability for producing hollow sections
varies from material to material. There are even
differences between aluminum alloys, which ap-
pear to be predestined for hollow section pro-
duction. Numerous precipitates or phase segre-
gations with foreign lattice structures can impair
the bonding. The hot strength of the high- Fig. 4.55 Extrusion weld in aluminum. (a) Different etchant
attack. (b) Full recrystallization across the weld
strength materials can be so high that the large [Ake 92]
182 / Extrusion, Second Edition
billet extrusion where transverse welds form Numerous metals react so severely at the high
(Fig. 4.56). extrusion temperatures required by adhesion
There is—however rarely used—the case with the extrusion tooling that the latter is im-
where the billet is extruded onto the discard of mediately destroyed unless protective measures
the previous billet (Fig. 4.56a). This is success- are taken (See section 4.12.5).
ful only after careful cleaning of the surfaces of This attack of the extrusion tooling and oxi-
the end faces and the removal of air to avoid dation of the hot billet can be avoided by clad-
blisters and material separation in the extrusion. ding the billet of the reactive material (Be, Ti,
This process is used in aluminum cable sheath- Zr, Hf, V, Nb, Ta) with copper or iron. Even
ing (see section 3.6 in Chapter 3). alloy steel can be clad for specific purposes with
With aluminum alloys, the discard is usually mild steel, an aluminum alloy with pure alumi-
sheared off (solid section dies and porthole dies, num, or even aluminum with copper to give just
Fig. 4.56c) or pulled off (bridge dies, Fig. 4.56d) a few examples.
before the next billet is extruded. If a solid sec- To ensure that a solid bond forms between the
tion is extruded through a flat die, then a “feeder sheath and the billet by pressure welding, both
chamber” is normally used (Fig. 4.56b). The res- carefully degreased components must undergo
idue of the first billet remaining in this feeder such severe deformation in the deformation zone
chamber behaves in the same way as the residue (at least 50%) that any brittle surface coating
in a hollow section die after removal of the dis- present (oxide) breaks up and pure metals con-
card. It can bond by adhesion with the subse- tact each other.
quent billet. This usually occurs because the dif- The diffusion of atoms across the boundary
ferent flow conditions between the regions close surface can simplify the bonding by transposi-
to the surface and the core of the section result tion processes. On the other hand, these diffu-
in the material of the next billet flowing as a sion processes can also result in the formation
tongue into the material from the preceding bil- of undesired alloy layers at the contacting sur-
let so that the contact surfaces are extensively faces. In the worst cases, a low-melting-point
increased. secondary phase can form from the atoms of the
two components. Table 4.1 lists these low-melt-
4.12.3 Composite Extrusion ing-point phases in the corresponding binary
Composite extrusion is used to produce sec- system base material-cladding. The extrusion
tions from two or more different materials, usu- temperature must not exceed these limits [Ric
ally with a constant cross-sectional distribution 69].
over the entire length. The process and practical If intermetallic brittle phases form by diffu-
applications are given in Chapter 5 in the section sion during the pressure welding between the
“Extrusion of Semifinished products from Me- sheath and the base material (e.g., between zir-
tallic Composite Materials.” This section covers conium and iron), this is not always detrimental
the mechanism of the bonding of two materials because the bond zone can be kept extremely
during extrusion. thin.
Fig. 4.56 Extrusion of aluminum “billet-on-billet” [Ake 92]. (a) Extrusion of a billet on the discard in the container. (b) With feeder
die. (c) In the ports of a porthole die. (d) Pulling off the discard in a bridge die [Ake 92]
Chapter 4: Metallurgical Principles / 183
Table 4.1 Liquid phases between the cladding and the billet
Lowest temperature for the formation of liquid
phases (C) with
Element Melting point, C Transformation point, C Copper Nickel Iron
Beryllium 1280 ... 850 1157 1165
Titanium 1720 882 885 942 1085
Zirconium 1860 862 885 961 934
Vanadium 1900 ... ... 1203 1468
Niobium 2410 ... 1080 1175 1360
Tantalum 3000 ... 1080 1360 1410
Source: [Ric 69]
It is not only the intermetallic phases that withstand tensile forces even during elongation
form during extrusion that can damage the sur- of the extruded section and thus increase the
face zone of the extruded base material to such strength. The softer metallic matrix transfers the
an extent that different properties exist relative forces under load into the fibers, which deter-
to the core after removal of the cladding, e.g., mine the strength [Kel 73].
corrosion susceptibility. The formation of a solid The behavior of the fiber-reinforced metallic
solution between the cladding material and the materials at different temperatures can only be
base metal can also result in the same problems. explained to a limited extent by the behavior of
The selection of the cladding material and the the base material. At low temperatures, the fibers
extrusion parameters must, therefore, be care- increase the strength. At high temperatures, in
fully considered. contrast, the base material can shear at the in-
Other types of composite materials are pro- terface with the fibers. This can damage the ma-
duced so that a second or third material in the terial in such a way that it fails before a material
form of bar is added to the billet. Super conduc- without fibers [Scu 92].
tors or contact wires can be produced by placing
suitable bars or wires into holes in a copper bil-
let. This is then extruded. 4.12.4 Powder Extrusion
In certain cases extrusion is carried out with The process and the application of powder ex-
the knowledge that intermetallic phases will trusion is described in detail in the section “Ex-
form between two adjacent materials, e.g., to trusion of Powder Metals” in Chapter 5 (see also
achieve a high wear resistance or super con- [Sch 86]). This section covers the metallurgy of
ducting properties [Web 82]. this process.
There is also composite extrusion between The particles of loose or cold compacted pow-
two metals that exhibit extremely different prop- der have a fill density of 50 to 80%; i.e., de-
erties and that apparently do not react with each pending on the production process the round or
other at the extrusion temperature. One example angular particles contact each other, at best, in-
is the production of a composite of an aluminum completely. After cold compaction the particles
section and a steel strip in which the wear resis- have to some degree linked together and in some
tance of the steel and its high hardness are util- places even adhesively bonded so that the sta-
ized where the section is subjected to high bilized billet (green compact) can withstand the
stresses [Mie 87]. handling before extrusion without breaking. In
In fiber composite materials, metallic or non- the press the particles are initially to some extent
metallic fibers are embedded in a metallic matrix plastically deformed so that they contact virtu-
to improve the mechanical properties. The ad- ally over the entire surface. A certain amount of
hesive bonding between the fibers and the base relative movement between the particles in this
material is usually low because the lattices are accommodation process results in the particles
so different and, in the case of nonmetallic fi- also rubbing together. This is believed to pro-
bers, a metallic bond cannot be produced. Stiff duce partial friction welding [She 72]. This pro-
fibers are broken into small pieces during extru- cess is either stopped in front of or at the start
sion by the elongation of the parent metal—the of the deformation zone by the plastic elongation
higher the extrusion ratio, the smaller the pieces. corresponding to the extrusion ratio. The ap-
These pieces are mechanically held so tightly in proximately round powder particles become
the base material without adhesion that they can elongated fibers. The surface area of the particles
184 / Extrusion, Second Edition
is increased to such an extent that brittle surface fiber materials, because the adhesive effect is
coatings, usually oxides, break up to free the weak with different metallic lattices and com-
pure metal. A good lattice match, combined with pletely absent with metallic inclusions. With
transposition processes across the boundaries their small size, however, they are embedded so
between the individual grains, develops a good securely in the base material that this is not im-
adhesive bond by pressure welding [Rob 91]. portant. If the hard particles or their material
The extruded section has a fine structure cor- fraction are too large, tearing at the boundary
responding to the powder grain size that can surfaces can result in a decrease in strength. Vol-
scarcely be distinguished under the microscope ume fraction, size, and distribution of the hard
from that of an extruded cast billet. However, particles have to be carefully balanced.
the structure of a cast (or preforged) billet is usu-
ally coarse grained and exhibits in correspond- 4.12.5 Friction between the Extruded
ing materials coarse primary precipitates that Material and the Tooling
have a negative influence on the quality of the The friction conditions between the billet and
extruded section. The fine-grain structure of the container as well as at the end faces and on
powder of the same composition is, in contrast, the die working faces play a very important role
far more homogeneous (e.g., [Asl 81]). in extrusion. This section discusses only the
With perfect bonding, the mechanical prop- physical and metallurgical aspects of these pro-
erties of a material produced from either a cast cesses. The basics of lubrication are also
billet or a powder metallurgical material of the touched on (more information on adhesion is
same composition are largely identical. given in [Tyl 68]).
For dispersion hardening, hard particles of an In the absence of lubrication, there is direct
intermetallic phase or a nonmetal (usually ox- contact between the tooling and the extruded
ides, nitrides, or carbides) are embedded in the material. The roughness of the tool surface is
base material by powder extrusion. The effect of determined by the machining. The high pressure
these particles corresponds exactly to that of pre- in extrusion smears the plastically deformed ma-
cipitates described in section 4.7. They act as terial into the depressions and as it glides over
barriers to dislocation movement, which in- the tool, it has to travel over the peaks and into
creases the yield strength and the work harden- the valleys. This process results in friction.
ing. The number and distribution of the particles The adhesion between the tool and the material
and not the size are important: the finer the dis- is more important. It occurs where there is metal-
tribution, the greater the effect. to-metal contact. The partial adhesion and break-
The particles added by powder metallurgy are ing away of the material at the tool increases the
resistant to very high temperatures in contrast to friction between both. The adhesion can, how-
precipitates in cast alloys. Coagulation and dis- ever, be larger than the cohesion within the ma-
solution are impossible. Therefore, the applica- terial. Particles of the material torn from its sur-
tion of dispersion-hardened materials is mainly face adhere to the tool. It is also possible for the
attributable to the high-temperature properties. pieces of the tool surface to be torn away and to
They are still effective at very high temperatures pass out with the extruded section. This increases
where other strength-increasing methods fail the roughness of the tool. High pressure and tem-
(work hardening, dissolved foreign atoms, pre- perature increase the adhesive tendency.
cipitated particles), e.g., [Mat 90] (Fig. 4.57). This tendency to adhesion varies with the
Very finely distributed dispersoids also hinder material/tool combination. It can be assumed
grain-boundary migration, which leads to re- that a slight adhesion tendency and thus a low
crystallization. Finely distributed aluminum ox- friction force occurs where both partners only
ide particles in a copper matrix can, for example, slightly dissolve in each other. Aluminum and
completely suppress recrystallization at 1000 C, titanium adhere very strongly with steel tooling.
which is just below the melting point. This This, naturally, also applies to steel because the
means that cold work-hardened materials also adhesion tendency between partners of the same
have a higher strength at high temperatures than material is particularly marked. On the other
the original soft material because of the retention hand with copper the adhesion tendency to steel
of grain boundaries that hinder dislocation tooling is only half as high as that of aluminum
movement [Zwi 57]. [Czi 72].
The boundary surfaces matrix-hard particles The tooling surface is oxidized at the extru-
do not usually have good adhesion, similar to sion temperature. The adhesion tendency will be
Chapter 4: Metallurgical Principles / 185
700
600
1
1) AlZnMgCu 1.5
(age hardened at elevated
500 temperature)
Tensile strength, MPa
2) Aluminum with
10% Al2O3 sintered aluminum
400
powder (SAP)
2 Dispersion hardened with 4% C
3) AlMg3.5Cr
300 (solid-solution hardened)
3
4) Al 99
200
4
100
0
0 20 100 200 300 400 500
Temperature, °C
Fig. 4.57 Hot strength of normal and dispersion-hardened aluminum alloys [Jan 75]
reduced by this oxide coating on the hot tool. Its surface thus behaves hardly differently from a
effect has still not been extensively studied. slightly rougher one. The roughness measured
Probably, poorly bonding oxides are partly torn perpendicular to the section corresponds to the
away and carried out with the extruded section roughness of the aluminum coating on the die
so that the clean tool surface comes into contact bearing surface [The 93] (see also Chapter 6, the
with the material. section on extrusion of aluminum alloys).
Even without taking into account the adhesion “Crow’s feet” or “pickup” are particles that
from the relative movement material/tooling, the have been torn out within the die opening and
plastic deformation needed for smearing at the have bonded to the tool. They produce grooves
surface structure of the hard tool produces heat. in the surface. They continue to grow until the
The catching on and releasing of the material shear force exerted by the extrusion is sufficient
caused by the adhesion can also produce local to tear them away and to carry them out with the
temperature peaks that can approach the melting extruded section [Mer 77].
point of the material. They are, however, im- Nitriding, which is usually used to harden the
mediately reduced by the good conductivity of surface of extrusion dies for aluminum alloys,
the metal. Both processes are the cause for the has only a slight effect on the adhesion behavior
temperature increase due to friction at the ma- but does prevent premature wear of the tool sur-
terial surface. face. Grooves in the tool thus occur later, if at
The thin but firmly bonded oxide layer on alu- all. The aluminum coating does form later on
minum is broken up by a large deformation even nitrided tooling during extrusion than on unni-
at high temperatures. The clean metal comes trided tooling. Once it has formed then, as far as
into contact with the tooling during extrusion. A the section surface is concerned, there is no
thin layer of aluminum quickly forms on the longer any difference [The 93].
bearing surface of the die, and this bonds so sol- The container liner surface is coated with sol-
idly because of the adhesion that the profile idly bonded aluminum, even after the first ex-
formed in the bearings largely slides along alu- trusion, because of the strong adhesion tendency
minum and not steel [Ake 83]. A smooth bearing between steel and aluminum already mentioned.
186 / Extrusion, Second Edition
After this, the billet no longer slides or, more Glass lubrication in the Séjournet process is
correctly, shears, over steel during extrusion but the current practice for high-temperature extru-
over aluminum [Ake 83]. sion (stainless steels, nickel alloys, etc.). This is
Only extrusion without lubrication has been described in detail in the section “Extrusion of
considered so far, which is usual for aluminum. Iron-Alloy Semifinished Products” in Chapter 5.
Lubricants—including certain oxides—should It should also be mentioned that the thermal in-
separate the material and the tooling and hinder sulation between the material and the tooling
any friction reaction between them (see [Sce 83] plays an important role in addition to the good
for a more detailed discussion). lubrication properties.
The lubricant film has to bond both to the The billet and tooling have to be completely
tooling and the material. The slip takes place wetted by the glass lubricant. Good adhesion is
within the lubricant film itself. The selected lu- also a requirement and it should also not attack
bricant film has to be thick enough not to break the metal. The glass film on the extruded section
down and must have the correct viscosity should be approximately 10 to 30 lm thick.
(toughness) at the extrusion temperature. The lu- The relative movement between the material
bricant on one hand has to be able to follow the and the tooling occurs entirely within the glass
severe increase in the surface area in extrusion film, the viscosity of which corresponds to a first
and, on the other hand, must not be squeezed out approximation to a Newtonian liquid:
under the high extrusion pressure.
Only a few metal oxides act as lubricants and Viscosity g ⳱ A • exp(E/RT )
only copper oxide is so ductile at the extrusion
temperature and bonds to the tooling and billet The glass film becomes more fluid as the tem-
solidly enough while retaining the sliding effect perature increases. Pressure dependence of the
that the container does not have to be lubricated
glass viscosity has not been found.
at all and the die only slightly. However, an in-
Different glass compositions are recom-
complete coating of the billet surface with oxide
mended to give the correct viscosity, which
results in irregularities in the slip of the billet
should be between 10 and 100 Pa • s, at the
along the container liner wall and to defects in
the extruded section (see the section on copper different extrusion temperatures and extrusion
alloys in Chapter 5 for more information). ratios. The table in Fig 4.58 gives the compo-
If nonlubricating oxides in copper alloys sition of different glasses and shows some vis-
dominate, e.g., zinc oxide in CuZn alloys cosity curves.
(brass), the lubricating effect of the copper oxide
is lost. 4.13 Extrudability of
The usual lubricants with copper alloys and Metallic Materials
other materials with moderate extrusion tem-
peratures are graphite containing lubricating Good extrudability is a collective term for a
oils, which can be classified under the heading low-extrusion load, high extrusion speed, good
“solid lubrication.” The hexagonal structure of surface finish, freedom from defects, tight di-
graphite, the base surfaces of which exert only mensional tolerances, and high tooling through-
a weak attraction force between each other, is put. The breadth of the term makes definitions
the reason that graphite plates easily slide over and deductions difficult. In general, a material is
one another. The oil in which the graphite plates described as having a better extrudability than
are embedded acts as a carrier and ensures that another if it has better hot-working characteris-
the lubricant bonds to the tooling with a suitable tics in extrusion when specific extrusion param-
thickness. eters are held constant. Extrusion materials are
If the extrusion temperature is higher than ap- classified by this term into high, moderate, and
proximately 1000 C, graphite is unsuitable as a low extrudability.
lubricant because it is destroyed by oxidation, as One material from an alloy family can then
is the carrier oil. Molybdenum disulfide, which have a higher extrudability than another if:
exhibits at room temperature and slightly ele-
vated temperatures outstanding lubrication ● The maximum extrusion speed before the
properties—attributable like graphite to its crys- occurrence of surface defects (roughness,
tal structure—loses its effect by oxidation above grooves) under otherwise equal conditions
300 C. It is therefore not suitable for extrusion (initial billet temperature, container tempera-
at higher temperatures. ture, extrusion ratio, die) is faster.
Chapter 4: Metallurgical Principles / 187
Fig. 4.58 Dependence of the viscosity of glass lubricants on the temperature [Sce 83]
● The extrusion load under otherwise equal flaking, and cracks) and increase the tool
conditions (initial billet temperature, con- wear.
tainer temperature, extrusion ratio, die, ex- From the practical point of view it is impor-
trusion speed) is lower. tant to be able to use simple criteria before ac-
● The initial billet temperature and the con-
cepting an order and before using an unknown
tainer temperature under otherwise equal material to estimate whether and at what cost an
conditions (extrusion ratio, die, and extru-
order can be realized. The size and the type of
sion speed) are lower.
press available, the tooling, and the dimensions
The material and its properties influence the of the extruded product play a role in addition
extrudability in many ways: to the material.
● The melting point is a controlling factor for The theory of the extrusion load is given in
the deformation temperature and thus for the Chapter 3. Reference should be made to section
tooling life and for the subsequent process- 3.1.1.4 and the calculation example in Fig. 3.18.
ing of the extruded product by calibration or The values of kf or kw and gu cannot be ob-
finish drawing. tained from the data obtained from normal ten-
● Alloying additions (type and content) deter- sile tests since the strain that can be attained is
mine the flow stress, extrusion speed, and the too low because of the necking and because the
tendency to extrusion defects. rate of deformation in extrusion is several orders
● Large precipitates and inclusions can result of magnitude higher than the experimental con-
in the formation of surface defects (furrows, ditions on a tensile testing machine.
188 / Extrusion, Second Edition
The logarithmic principle strain rate u̇g of 1 Castle and Lang [Cas 78] developed a test die
to 10 sⳮ1 reached in torsion tests falls in the and test section with which it was possible to
range of the average logarithmic principle strain make a meaningful assessment of the material
rate in extrusion. In compression testing on fast properties of continuously cast material with and
presses, ug up to approximately 2 and u̇g up to without heat treatment (Fig. 4.60). The limiting
1000 sⳮ1 are achieved. speed for poor shape or tearing away of the ribs
The Atlas of Hot-Working Properties of Non- was determined. The necessary extrusion load
Ferrous Metals (Vol 1, Aluminum Alloys) [DGM can also be used as a measure of the extrudabil-
78] gathers the known data from the literature ity of a material.
in a standard format (ordinate: flow stress kf, ab- Many extrusion plants use similar test dies—
scissa: logarithmic principle strain ug with the even dies for hollow sections with correspond-
parameters temperature and principle strain ing ribs.
rate). For the extrusion press specialist it is dif- Figure 4.61 shows the various limiting speeds
ficult to find the necessary data for the extrusion for a range of alloys.
ratios of V ⳱ 10 to 300, corresponding to prin- The extrusion speed does not play such a large
ciple strains ug between 2 and 6 and the loga- role with materials that are extruded at moderate
rithmic strain rates u̇g between 0.5 and 10 sⳮ1 and high temperatures (e.g., copper alloys,
normally used in extrusion. steels); it is usually very high. In this case the
What helps in practice?
One suggestion made after trials with alumi-
num alloys was to define the extrusion behavior
by using a standard two-hole die [Mon 75] (Fig.
4.59) as follows: The farther the thicker section
travels during extrusion, the higher is the ex-
trudability of the material. Tests with this pro-
cess found it to be too insensitive. Seven-hole
dies of a specific design have also been used for
experiments [Mis 91].
Scharf estimated the extrudability of alumi- Fig. 4.60 Test section to estimate the extrudability of alu-
num alloys in experimental extrusions from the minum alloys using the extrusion speed as the lim-
iting factor [Cas 78]
extrusion time at a constant extrusion load. He
therefore used indirectly the extrusion speed as
the limiting parameter and could thus differen-
tiate between alloys and their heat treatment 1000
[Sca 64].
Al99.5
AlMgSi0.5
AlMgSi1
100
AlZnMg1
Stem speed, mm/s
10
AlCuMg1
AlZnMgCu1.5
AlCuMg2
10
0
Alloy type
flow resistance and thus the limiting extrusion A value of kw can then be calculated from Eq
load have to be taken into account. 4.1 (unlubricated container) or Eq 4.2 (lubri-
Hot-tearing tests can give a rough comparison cated container) using the coefficients g and l0
between the different materials. The dependence obtained from the practical measurements. It is
of the strength of different materials on the tem- then possible using Eq 4.1 or 4.2 to deduce pos-
perature is in principle correctly reproduced. sible billet or section dimensions for the material
The kf values obtained, however, cannot be used studied on this press [Ret 99].
to calculate the extrusion load. The very specific test process described to es-
The following method is known from the cop- timate the extrudability reflects the extent of the
per alloy processing industry: Equations 3.4, problem and the complexity of this term. At the
3.5, and 3.49 given in Chapter 3 in for the vari- same time such tests have become useful aids to
ation of the extrusion load during extrusion with determine optimal deformation conditions.
and without lubrication are used. Many extrusion plants also use their own test
For simplicity, the relevant formulae for the methods.
maximum extrusion load F0 are: Other criteria for the extrudability, including
freedom from defects, dimensional tolerances,
Unlubricated container FSt max and tooling life do not lend themselves to model
⳱ A0 • kw • ug Ⳮ D0 • p • (l0 ⳮ lR)s investigations and practical experience has to be
(Eq 4.1) used.
and
+z
a 1 2 3 4 +y
1
(a) +x
+z +z +z
+y +y +y
+x +x +x
(100) (110) (111)
(b) +z
[100]
]
11
[10
[1
1]
[010]
0] [11
[10 0] +y
+x
(c)
Fig. 4.62 Miller’s indices for space lattices. (a) Designation of lattice planes. (b) Examples of planes in the cubic lattice. (c) Examples
of directions in the cubic lattice
PR
0.5 1 4 24 16 8
1
0.5
4 0.5
8 4 TR
1 0.5
8 1 0.5
4
P
0.5
4 1
0.5
(011) [111]
0.5 1 4 24 16 8
(012) [100]
[111]
Fig. 4.63 Representation of textures in pole figures. [111] pole figure from the section core of an extruded AlCuMg bar [Moe 75]
Chapter 4: Metallurgical Principles / 191
over the number: e.g., ⳮ1 ⳱ 1̄. Figure 4.62(b) If deformation is carried out at a higher tem-
shows some examples of crystallographic planes perature and higher speed then, according to this
in a cubic lattice. relationship, the flow stress is the same as that
Directions in the unit cell are described with at a lower temperature and corresponding low
the location coordinates of a point on a line go- speed:
ing through the origin—also whole numbers but
this time within angular brackets. A surface di- ˙
kf ⳱ f (uexp(Q/RT))
agonal in the cubic lattice is designated with
[011], and a spatial diagonal with [111] (Fig. Or, using the Zener-Hollomon parameter Z:
4.62c).
kf ⳱ f (Z)
˙
Z ⳱ uexp(Q/RT)
Additional Information 2:
There are various expressions for the relation-
Representation of ship between the flow stress kf and the Zener-
Textures in Pole Figures Hollomon parameter Z that apply depending on
the material and temperature-speed situation:
In general, the orientation distribution in a
textured structure is shown on a stereographic Z ⳱ a • kaf Z ⳱ a • exp(b • kf)
projection in which a spherical surface is rep-
resented on a plane (known as the projection
plane). REFERENCES
The specimen is located in the center of the
sphere, and the normals of the crystallographic Books and Overviews
planes penetrate the surface of the sphere. A tex- [Alt 94]: D. Altenpohl, Aluminium von innen
ture is described by showing in the pole figure (Aluminum from the Inside), Aluminium-Ver-
the frequency of the orientations of individual lag, Düsseldorf, 1994
crystallographic planes (e.g., (111) or (100)). [Ber 83]: W. Bergmann, Werkstofftechnik, Teil
The pole plane coincides with a specific projec- 1: Grundlagen, Teil 2: Anwendung (Material
tion plane (e.g., the rolling plane in rolled Technology, Part 1: Fundamentals, Part 2:
sheets). In extruded or drawn bar the north-south Application), Carl Hanser Verlag, Munich,
direction of the pole figure is usually orientated Vienna, 1983
along the bar axis (Fig. 4.63). [Blu 93]: W. Blum, H. Mughrabi, and B. Rep-
pich, Grundlagen der Werkstoffkunde—Ni-
chteisenmetalle in Umformtechnik (Funda-
Additional Information 3: mentals of Material Science), Verlag
Temperature and Speed Stahleisen, Düsseldorf, 1993
[Dah 93]: W. Dahl, R. Kopp, and O. Pawelski,
Dependence of the Flow Stress in Umformtechnik—Plastomechanik und Werk-
Hot Working [Sel 79, Ake 70, McQ 90] stoffkunde (Non-Ferrous Metals in Deforma-
tion Technology), Verlag Stahleisen, Düssel-
In the stationary region of the work-hardening dorf, 1993
curve where work hardening and recovery are [Guz 70]: A.G. Guz and G. Petzow, Metallk-
in equilibrium, the flow stress is dependent on unde für Ingenieure (Metallurgy for Engi-
an exponential function of the temperature as neers), Akad. Verlagsges, Frankfurt, 1970
deduced from diffusion. The activation energy [Hor 67]: E. Hornbogen and H. Warlimont, Me-
is that for self diffusion: tallkunde (Metallurgy), Springer-Verlag, 1967
[Hou 93]: H.P. Hougardy, Grundlagen der
kf f (Q/RT) Werkstoffkunde (Fundamentals of Metal-
lurgy), Stahl in Umformtechnik, Verlag Stah-
At the same flow stress there is a simple rela- leisen, Düsseldorf, 1993
tionship between the strain rate and the absolute [Sce 83]: J.A. Schey, Tribology in Metalwork-
temperature T: ing, ASM International, 1983
[Sch 81]: W. Schatt, Einführung in die Werk-
u̇ ⳱ A • exp(ⳮQ/RT) stoffwissenschaft (Introduction to Material
192 / Extrusion, Second Edition
Science), VEB Deutscher Verlag für die Grun- [Asl 81]: C. Aslund, G. Gemmel, and T. An-
dindustrie, Leipzig, 4, Auflage, 1981 dersson, Stranggepreßte Rohre auf pulver-
[Tyl 68]: R.F. Tylecote, The Solid Phase Weld- metallurgischer Basis (Extruded Tubes with a
ing of Metals, Edward Arnold Ltd., London, Powder Metallurgy Base), Bänder Bleche
U.K., 1968 Rohre, Vol 9, 1981, p 223–226
[Wie 86]: A.G. Wielandwerke, Ulm: Wieland- [Bag 81]: J. Baumgarten, W. Bunk, and K.
Buch Kupferwerkstoffe (Wieland-Book Cop- Lücke, Strangpreßtexturen bei AlMgSi-Le-
per Alloys), Wieland-Werke AG, Ulm, 5, Au- gierungen, Teil 1: Rundstangen (Extruded
flage, 1986 Texture in AlMgSi Alloys, Part 1: Round
Poles), Z. Metallkde., Vol 72, 1981, p 75–81
Special Literature [Bau 59]: M. Bauser, “Einführung in die Physik
der plastischen Verformung der Metalle” (“In-
[Ake 66]: R. Akeret and A. Künzli, Ermittlung troduction to the Physics of the Plastic De-
der Formänderungsfestigkeitkf von Alumini- formation of Metals”), unpublished manu-
umlegierungen mit Hilfe von Torsionsver- script
suchen und Vergleich der Er-gebnisse mit [Bau 61]: M. Bauser, Verhalten von Nichteisen-
denjenigen von Strangpreßversuchen (Deter- Metallen bei der Warmumformung (Behavior
mination of the Flow Stress of Aluminum Al- of Nonferrous Metals in Hot-Working), Vor-
loys Using Torsion Tests and Comparison of trag Metallfachabend, Düsseldorf, 1961
the Results with Those from Conclusion Tri- [Bau 63]: M. Bauser, Verformbarkeit und
als), Z. Metallkde., Vol 57, 1966, p 7789– Bruchverhalten bei der Warmformgebung
7792 (Workability and Fracture Behavior in Hot-
[Ake 70]: R. Akeret, “Fließspannung und Struk- Working), Metall., Vol 17, 1963, p 420–429
tur bei der Warmumformung (von Alumin- [Bau 64]: M. Bauser, Zeit-temperatur-Auschär-
ium)” (“Flow Stress and Structure in Hot tungsschaubilder und die Festigkeit strang-
Working [of Aluminum]”), Alusuisse report gepreßter aushärtbarer Aluminiumlegierun-
220/70 gen (Time Temperature Age-Hardening
[Ake 83]: R. Akeret, Einfluß der Querschnitt- Diagrams and the Mechanical Properties of
form und der Werkzeuggestaltung beim Extruded Age-Hardening Aluminum Alloys),
Strangpressen von Aluminium, Teil II: Die Z. Metallkde,Vol 55, 1964, p 816–821
Reibung im Preßkanal (Influence of the [Bux 77]: K. Buxmann, Metall., Vol 31, 1977,
Cross-Section and Tool Design on the Extru- p 163–170
sion of Aluminum, Part II: Friction in the Die [Bux 77a]: K. Buxmann, Fachbericht (technical
Bearing), Aluminium, Vol 59, 1983, p 745– reports) FB 41/777/100 der Deutschen Ge-
750 sellschaft für Materialkunde, Oberursel, Ger-
[Ake 88]: R. Akeret, A. Ried, and J. Theler, J. many
Metall, Vol 42, 1988, p 760–769 [Cas 78]: A.F. Castle and G. Lang, Proceedings
[Ake 90]: R. Akeret and M. Textor, Strangpres- Aluminium Konferencia 78, Szébesfehérvar,
sen (Extrusion), DGM-Informationsgesells- Vol 1, 1978
chaft, Oberursel, Germany, 1990 [Czi 72]: H. Czichos, J. Appl. Phys., Vol 5,
[Ake 92]: R. Akeret, Strangpreßnähte in Alu- 1972, p 1980
miniumprofilen (Extrusion Welds in Alumi- [DGM 78]: Deutsche Gesellschaft für Metallk-
num Sections), Parts 1 and 2, Aluminium, Vol unde: Atlas der Warmformgebungseigen-
68, 1992, p 877–886 and 965–973 schaften von Nichteisenmetallen, Alumini-
[Ake 92a]: R. Akeret, “Extrusion Welds—Qual- umwerkstoffe (Atlas of Hot-Working
ity Aspects Are Now Center Stage,” presented Properties of Non-Ferrous Metals), Vol 1,
at International Aluminum Technology Sem- Aluminum Alloys, DGM, 1978
inar (Chicago, IL), May 20–22, 1992 [DGM 78a]: Deutsche Gesellschaft für Metallk-
[Alt 65]: D. Altenpohl, Aluminium und Alumi- unde: Atlas der Warmformgebungseigen-
niumlegierungen (Aluminum and Aluminum schaften von Nichteisenmetallen, Band 2,
Alloys), Springer-Verlag, 1965 Kupferwerkstoffe (Atlas of Hot-Working Prop-
[And 48]: W.A. Anderson and R.F. Mehl, Trans. erties of Non-Ferrous Metals), Vol 2, Copper
AIME, Vol 161, 1948, p 140 Alloys, DGM, 1978
[Ash 79]: M.F. Ashby, C. Gandhi, and D.M.R. [Die 77]: O. Diegritz, “Preßfehlerkatalog; Feh-
Taplin, Acta Metall., Vol 27, 1979, p 699–729 lererscheinungen bein direkten Strangpressen
Chapter 4: Metallurgical Principles / 193
von Kupferwerkstoffen” (“Defects in the Di- rial Science and Technology, Vol 6, Akad.
rect Extrusion of Copper Alloys”), manu- Press, New York, 1975, p 393–493
script, AK Schwermetall im Strang- [McQ 90]: H.J. McQueen, Micromechanisms of
preßausschuß, DGM Dynamic Softening in Aluminum Alloys dur-
[Fie 57]: D.S. Fields and W.A. Backofen, De- ing Hot Working, Hot Deformation of Alu-
termination of Strain Hardening Characteris- minum Alloys Proc. (Detroit, MI), 1990
tics by Torsion Testing, Proc. Amer. Soc. Test. [McQ 90a]: H.J. McQueen, Effect of Solutes
Mat., Vol 57, 1957, p 1259–1272 and Precipitates on Hot Working Behavior of
[Fle 74]: M.C. Flemings, Solidification Process- Al Alloys, Hot Deformation of Aluminum Al-
ing, McGraw-Hill Inc., 1974 loys Proc. (Detroit, MI), 1990, p 105–120
[Fra 50]: F.C. Frank and W.T. Read, Phys. Rev., [Mer 77]: G. Merk and S.E. Naess, Pick-Up
Vol 79, 1950, p 722–723 Formation on Aluminium Extrusion, Z. Me-
[Got 84]: G. Gottstein, Rekrlstallisation metal- tallkd., Vol 68, 1977, p 683–687
lischer Werkstoffe (Recrystallization of Me- [Mie 87]: G. Mier, Verbundstromschienen Al-
tallic Materials), Deutsche Ges., F. Metallk- uminium-Stahl für S-und U-Bahnen (Com-
unde, e.V., 1984 posite Bus-Bars in Aluminum Steel for S and
[Grz 93]: B. Grzemba and J. Hasenclever, Non- U Trains), Schweizerische Aluminium Rund-
Ferrous Metals Volume Using Aluminum and schau (Swiss Aluminum Review), 1987,
Copper as Examples, Umformtechnik, Kopp p 12–17
und Pawelski, Ed., Verlag Stahleisen, Düssel- [Mis 91]: W. Misiolek and J. Zasadzinski, Test-
dorf, 1993 Die for Estimation of the Extrudability of
[Haa 84]: P. Haasen, Physikalische Metallkunde Metals, Aluminium,Vol 67, 1991, p 85–89
(Physical Metallurgy), Springer-Verlag, Ber- [Möl 75]: M. Möller, “Werkstoffluß, Grobkorn-
lin, 1984 bildung und Preßeffekt bei stranggepreßtem
[Hof 62]: W. Hofmann, Lead and Lead Alloys, Aluminium (AlCuMg)” (“Course Grain For-
Metallurgy and Technology, Springer-Verlag, mation and Extrusion Effect in Extruded Alu-
2, Auflage, 1962 minum”), dissertation, Technical University
[Jan 75]: G. Jangg, F. Kutner, and G. Korb, Her- of Clausthal, Germany, 1975
stellung und Eigenschaften von dispersions- [Mon 75]: L.F. Mondolfo, A.R. Peel, and J.A.
gehärtetem Aluminium (Production and Prop- Marcantonio, Met. Technol., Sept 1975, p 433
erties of Dispersion Hardened Aluminum), [Mor 69]: G. Moritz, Z. Metallkde., Vol 60,
Aluminium, Vol 51, 1975, p 641–645 1969, p 742–749
[Kat 67]: T.Z. Kattamis, J.C. Coughlin, and [Mug 84]: H. Mughrabi, Mechanisms and Me-
M.C. Flemings, Trans. AIME, Vol 239, 1967, chanics of Plasticity, Rev. Phys. Appl., Vol 23,
p 1504–1511 1984, p 367–379
[Kel 73]: A. Kell, Werksstoffe hoher Festigkeit [Ohm 88]: L. Ohm and S. Engler, Aluminium,
(High Strength Material), Vol 4, Verlag Vol 64, 1988, p 513–520
Vieweg, Wiesbaden, Germany, 1973 [Ohm 89]: L. Ohm and S. Engler, Metall., Vol
[Lan 89]: G. Lang, Warmformverhalten von Al- 43, 1989, p 539–543
uminiumlegierungen beim direkten Strang- [Ray 49]: G.V. Raynor, Ann. Equilibr. Dia-
pressen (Hot-Working Characteristics of Alu- grams, No. 2, 1949
minum Alloys in Direct Extrusion), [Rei 80]: W. Reif and W. Schneider,
Aluminium, Vol 65, 1989, p 291–294 Gießereiforschung, Vol 32, 1980, p 53–60
[Los 77]: E. Lossack, Erzmetall, Vol 30, 1977, [Res 92]: O. Reiso, Ph.D. thesis, Norwegian In-
p 243 stitute of Technology, Trondheim, Norway,
[Los 83]: E. Lossack and W. Schneider, Gal- 1992
vanotechnik, Jahrg, Vol 74, 1983, p 787–794 [Ret 99]: W. Rethmann, Pers Mitteilung KM-
[Mat 90]: K.H. Matucha, K. Drefahl, G. Korb, Kabelmetall AG (communication from KM-
and M. Rühle, Neue oxiddispersionsge-här- Kabelmetall AG), Osnabrück, Germany, 1999
tete Legierungen für Hochtemperatur-An- [Ric 69]: H. Richter, Die Herstellung von Stan-
wendungen (New Oxide Dispersion Hard- gen, Rohren und Profilen durch Verbund-
ened Alloy for High Temperature strangpressen (The Production of Bars, Tubes
Application), VDI-Berichte (VDI-Reported), and Sections by Composite Extrusion), Z. Me-
1990, Vol 797, p 125–152 tallkde., Vol 60, 1969, p 619–622
[McQ 75]: H.J. McQueen and J.J. Jonas, Plastic [Rie 87]: H. Riedel, Fracture at High Tempera-
Deformation of Materials. Treatise on Mate- tures, Springer-Verlag, Berlin, 1987
194 / Extrusion, Second Edition
[Rob 91]: Roberts and Ferguson, Strangpressen [Stü 69]: H.-P. Stüwe, Einfluß einer plastischen
von Pulvermetallen (Extrusion of Powder Verformung auf Phasenumwandlungen in
Metals), Int. Mater. Rev., Vol 36, 1991, Metallen (Influence of a Plastic Deformation
p 62–79 on the Phase Transformations in Metals),
[San 75]: R. Sandström and R. Lagneborg, Acta Härt.-Tech. Mitt., Vol 24, 1969, p 1–5
Metall., Vol 23, 1975, p 387 [The 93]: W.W. Thedja, K. Müller, and D. Rup-
[Sca 64]: G. Scharf, Einfluß der chemischen Zu- pin, Die Vorgänge im Preßkanal beim Warms-
sammensetzung auf Preßbarkeit und Festig- trangpressen von Aluminium: Reibung im
keit von AlMgSi0.5 (Influence of the Chem- Preßkanal und Matrizenverschleiß (The Pro-
ical Composition on the Extrudability and cesses in the Die Aperture in the Hot-Extru-
Strength of AlMgSi0.5), Z. Metallkde., Vol sion of Aluminum: Friction in the Die Aper-
55, 1964, p 740–744 ture and Die Wear), Aluminium, Vol 69, 1993,
[Sch 86]: W. Schatt, Pulvermetallurgie (Powder p 524–528 and 649–653
Metallurgy), Hüthig-erlag, Heidelberg, Ger- [Web 82]: H.R. Weber, Extrusion of Technical
many, 1986 Superconductors, Extrusion symposium, DGM,
[Scn 85]: W. Schneider, Aluminium, Vol 61, 1982, p 277–296
1985, p 338–345 [Wei 94]: H. Weiland, T.N. Rouns, and J. Liu,
[Scu 92]: K. Schulte, Metal-Matrix Composites The Role of Particle Stimulated Nucleation
with Aluminium Matrix: Advanced Aerospace during Recrystallization of an Aluminum-
Materials, Springer-Verlag, 1992, p 108–118 Manganese Alloy, Z. Metallkde., Vol 85,
[See 85]: A. Seeger, Kristallplastizität. Hand- 1994, p 592–597
buch der Physik (Handbook of Physics), [Wev 54]: F. Wever and A. Rose, Atlas zur Wär-
Springer-Verlag, Berlin, VII/2, p 1–210 mebehandlung der Stähle (Atlas on the Heat
[Sel 79]: C.M. Sellars, The Physical Metallurgy Treatment of Steels), Verlag Stahleisen, Düs-
of Hot Working, Proc. Int. Conf. Hot Working seldorf, 1954
and Forming Processes (Sheffield, U.K.), [Wie 86]: A.G. Wieland werke, Wieland-Book
1979, p 3–15 Copper Alloys, Ulm, 5, Auflage, 1986.
[She 72]: T. Sheppard and P.J.M. Chare, Powder [Zwi 57]: K.M. Zwilsky and N.J. Grant, J. Met.,
Metall., Vol 15, 1972, p 17–41 Vol 9, 1957, p 1197–1201
Extrusion: Second Edition Copyright © 2006 ASM International®
M. Bauser, G. Sauer, K. Siegert, editors, p 195-321 All rights reserved.
DOI:10.1361/exse2006p195 www.asminternational.org
CHAPTER 5
THE HOT-WORKING PROCESS extrusion ered to be the most important of the hot-working
is, in contrast to other compressive deformation processes.
processes used to produce semifinished prod-
ucts, a deformation process with pure compres-
sive forces in all three force directions. These
favorable deformation conditions do not exist
in other production processes for semifinished
products. Even in rolling, which is the most im- Extrusion of Materials with
portant compressive working process for pro-
ducing semifinished products, tensile forces oc-
Working Temperatures
cur in the acceleration zone of the roll gap as between 0 and 300 ⬚C
well as in the cross rolling process used to
pierce blanks in the rolling of steel tubes. These Günther Sauer*
tensile forces cause problems in the rolled prod-
uct if the deformation conditions are not opti-
mized. The benefits of this three-dimensional
compression in terms of deformation technol- 5.1 Extrusion of Semifinished
ogy, which have already been discussed in this Products in Tin Alloys
book, can be clearly seen in Fig. 5.1 based on
experimental results for face-centred cubic (fcc) Tin is a silver-white, very soft metal with a
aluminum and zinc with its hexagonal lattice stable tetragonal lattice in the temperature range
structure. 20 to 161 ⬚C. The pure metal has a density of
The extensive variations in the extrusion pro- 7.28 g/cm3 and a melting point of 232 ⬚C.
cess enable a wide spectrum of materials to be The material can be easily worked with its
extruded. After rolling, extrusion can be consid- recrystallization temperature below room tem-
*Extrusion of Materials with Working Temperatures between 0 and 300 ⬚C, Günther Sauer
Extrusion of Semifinished Products in Magnesium Alloys, Günther Sauer
Extrusion of Semifinished Products in Aluminum Alloys, Rudolf Akeret
Materials, Günther Scharf
Extrusion of Semifinished Products in Copper Alloys, Martin Bauser
Extrusion of Semifinished Products in Titanium Alloys, Martin Bauser
Extrusion of Semifinished Products in Ziroconium Alloys, Martin Bauser
Extrusion of Iron-Alloy Semifinished Products, Martin Bauser
Extrusion of Semifinished Products in Nickel Alloys (Including Superalloys), Martin Bauser
Extrusion of Semifinished Products in Exotic Alloys, Martin Bauser
Extrusion of Powder Metals, Martin Bauser
Extrusion of Semifinished Products from Metallic Composite Materials, Klaus Müller
196 / Extrusion, Second Edition
perature. Consequently, the softest condition de- surface and the container inner wall because of
velops rapidly in tin materials after cold work- these good bearing properties. Tin-base extruded
ing. Work hardening by cold working is not alloys, therefore, tend to flow largely according
possible. to flow pattern A (Fig. 3.11) in direct extrusion.
Tin is very stable at room temperature and is The flow stress kf that has to be overcome for
not poisonous. Unlike lead, it can therefore be the deformation of very soft pure tin is signifi-
used in contact with food. The metal is used as cantly higher than that of pure lead, as can be
the base material for soft solder, anode materials clearly seen in Fig. 5.2. It is, however, extremely
as well as bearing materials and for tin plating low at 20 to 32 N/mm2 for logarithmic strains
steel sheet (tin plate). ug up to 0.7 [Sac 34]. Therefore, a specific press
Soft solders are the main application for tin. pressure of maximum 400 N/mm2 is sufficient
Lead, silver, antimony, and copper are used as for the direct extrusion of tin alloys when the
alloying elements. Special soft solders also con- low friction between the billet and the container
tain cadmium and zinc. Aluminum is used as an liner surface is taken into account.
alloying component for soft solders used to join Tin-base alloys for the production of soft sol-
aluminum alloys. Bearing metals based on tin ders are generally extruded transversely at billet
contain antimony, copper, and lead as the alloy- temperatures of 50 to 60 ⬚C and a container tem-
ing elements as well as additions of cadmium, perature of approximately 100 ⬚C. It is often suf-
arsenic, and nickel. ficient to heat the front third of the billet to this
The production of semifinished products in tin temperature so that, on one hand, the billet up-
alloys by extrusion is limited today to the pro- sets from the front to the back to prevent air
duction of feedstock for the manufacture of soft entrapment and, on the other hand, the optimal
and special soft solders on transverse extrusion welding conditions for the resultant transverse
presses and to the direct extrusion of feedstock weld in the extruded product are obtained. This
for the manufacture of anodes with solid and transverse weld in soft solders has to be capable
hollow cross-sectional geometries for electro- of withstanding the drawing loads during the re-
chemical plating. Tin is also used for the pro- duction in diameter of the extruded wires on
duction of rolled strip, as the feedstock for the multispindle drawing machines.
manufacture of high-capacity electrical con- Semifinished products in tin materials includ-
densers, as well as for roll cladding of lead-base ing bar, wire, tubes, and sections are produced
strips for organ pipes, wine bottle caps, and on direct extrusion presses. For productivity rea-
Christmas ornaments (tinsel). sons, higher extrusion speeds are desired in this
In general, tin-base materials have good bear- process than those used in the transverse extru-
ing properties and are consequently used as the sion of soft solders, which are typically 4 m/min.
base material for bearing metals. Very little fric- It is therefore advantageous to heat the billets to
tion occurs in direct extrusion between the billet 100 to 150 ⬚C. Again, it is beneficial to have a
temperature profile with the temperature de-
creasing toward the back of the billet. In auto-
matic fully integrated extrusion plants complete
with melting furnaces and mold casting ma- Simple two-column horizontal oil-hydraulic
chines, as shown in Fig. 5.3, the cast billets re- extrusion presses are used. Figure 5.3 shows a
tain the heat from the casting process to assist typical two-column extrusion press for tin and
the deformation process. Care has to be taken to tin alloys with a maximum press load of
ensure that the heat from the casting process, 5000 kN.
when combined with the deformation heat, does
not result in excessive temperatures at high ex-
trusion speeds in the deformation zone of the
extrusion tooling. The solidus of the lead-tin eu- 5.2 Extrusion of Semifinished
tectic at 183 ⬚C has to be taken into account in Products in Lead Materials
the tin alloys containing lead. If melting occurs
in the solid tin matrix, transverse cracks will def- Lead is a soft metal, matte blue in appearance
initely be produced in the extruded products. with a fcc lattice structure. The pure metal has
Controlled cooling of the extrusion tooling im- a very high density of 11.34 g/cm3 and a melting
proves the situation. In addition, the billet sur- point of 327 ⬚C. Lead alloys can also be easily
face is sometimes brushed with a lubricant to worked. Work hardening after cold working at
improve the product surface. room temperature, for example, from 40 to 120
Tin alloys will weld during the extrusion pro- N/mm2 disappears within a few minutes because
cess under suitable deformation conditions in- the recrystallization temperature of the base ma-
cluding the extrusion load and temperature. terial is about 0 ⬚C. Cold working of lead-base
They can, therefore, be used with porthole and alloys can be approximately compared in its ef-
bridge dies as well as for billet-on-billet extru- fect to hot working of other metals. Work hard-
sion with feeder chamber dies. These extrusion ening by cold working is not possible.
tools are, in principle, similar to those used in Pure lead is very soft and ductile. Soft lead
aluminum extrusion. Their design is simpler in has a very low flow stress kf as shown in Fig.
detail and the dies are nitrided. 5.2. It is, therefore, not possible to draw pure
Fig. 5.3 Modern integrated fully automatic 5000 kN extrusion plant for the production of bar, wire, tube, and sections in lead and
tin alloys complete with casting oven, triple billet casting plant, hot-billet shear, and oil hydraulic long-stroke extrusion
press (Source: Collin)
198 / Extrusion, Second Edition
lead to wire. However, lead alloys have higher the production of soft solders. Lead forms a eu-
flow stresses. Additions of antimony and tin pro- tectic with 38.1% tin at 183 ⬚C. These soft sol-
duce solid-solution hardening of the lead, in- ders can be used to solder steel and copper al-
creasing both the base strength and the work- loys. Organ pipes are produced from lead-tin
hardening capability. This raises the alloy strips with similar tin contents. Tin con-
recrystallization temperature. The loads needed tents from 45 to 75 wt% are used depending on
in deformation processes also increase. Anti- the timbre. Lead-tin-antimony alloys with ad-
mony and zinc are the main alloying elements ditives of arsenic, cadmium, and nickel are very
for lead, although small amounts of arsenic and important as bearing metals.
cadmium, as well as copper nickel and silver, Table 5.1 gives recommended lead alloys for
are also used. the extrusion of rod, wire, tubes, sections, and
Lead antimony alloys are referred to as hard cable sheathing. Lead alloys are extruded with
lead because the antimony significantly hardens deformation temperatures in the range 100 to
the soft lead. Alloys of this type with antimony 260 ⬚C, depending on the composition, to obtain
contents up to 3 wt% also age harden. For ex- economic extrusion speeds of typically 50 to 60
ample, the Brinell hardness of an alloy with 2 m/min. On the other hand, lead-base soft solders
wt% antimony increases from 56 to 130 N/mm2 are extruded at significantly lower temperatures
within 100 days after quenching from 240 ⬚C. of approximately 55 ⬚C and slower speeds of 2
The toughness and the fatigue strength, as well to 4 m/min. When determining the billet and
as the corrosion resistance of these alloys, can container temperatures, care must be taken to
also be improved by the addition of specific ensure that any eutectics on the grain boundaries
amounts of tin. This is important for the me- do not melt as a result of excessive deformation
chanically fatigue loaded sheathed cables on, for temperatures in combination with the deforma-
example, bridges. Lead forms a eutectic with tion and friction heat during extrusion. A liquid
11.1% antimony at 253 ⬚C. This has to be taken metal phase on the grain boundaries of a solid
into account when determining the deformation metal matrix in extrusion will unavoidably pro-
temperature for the extrusion of PbSb alloys duce transverse cracks in the extruded product.
with eutectic, low-melting point phases on grain Lubricant is added to the billet surface with a
boundaries. controlled brush stroke.
Lead-tin alloys with their low solidus and li- Lead has even better bearing properties than
quidus temperatures are particularly suitable for tin. Lead alloys, therefore, also flow mainly ac-
cording to flow type A in direct extrusion as shown in Table 5.1 (see the section on cable
shown in Fig. 5.4 where the variation of the ex- sheathing in chapter 3).
trusion load over the container cross-sectional
area A0 is plotted as a function of the stem dis-
placement and the extrusion ratio [Sac 34, Hof
62]. 5.3 Extrusion of Tin- and
Lead alloys will weld during extrusion at suit- Lead-Base Soft Solders
able temperatures and extrusion pressures simi-
lar to tin alloys and certain aluminum alloys. The standard soft and special tin solders in
Tubes and hollow sections can, therefore, be ex- DIN 1707, as well as nonstandardized special
truded with porthole and bridge dies. Feeder soft solders, are extruded as solid bars, solder
chamber dies have also proved successful for the threads, solid wire, and hollow wire (tube sol-
extrusion of these materials and are required for der) filled with flux mainly on small hydraulic
billet-on-billet extrusion. The tools used for the automatic extrusion presses. The maximum ex-
extrusion of tin and lead alloys are in principle trusion loads are usually 2500 kN with a maxi-
similar to those used for aluminum extrusion, mum specific pressure of 600 N/mm2, which is
although the designs are simpler because of the required because of the extreme metal flow. The
significantly lower thermomechanical stresses. billet-on-billet process is used on transverse
All extrusion dies are nitrided. presses. Extrusion is usually followed by draw-
Extrusion plants consist of integrated auto- ing to the finished diameter of 5 to 0.5 mm on
matic complete plants with horizontal, hydrau- multispindle drawing machines. The majority of
lically operated two-column presses and maxi- finished diameters fall in the range 1 to 2 mm.
mum extrusion loads of 5000 to 10000 kN, as Special soft alloys with low cold-working ca-
shown in Fig. 5.3. A specific extrusion pressure pacities sometimes have to be extruded as mul-
of 400 N/mm2 is similar to tin-base extruded ma- tiple strands to the finished diameter using the
terials, adequate for the extrusion of lead-base direct extrusion process. Economic wire solder
alloys. presses operate completely automatically in the
Large tubes with internal diameters up to 300 same way as large extrusion plants with auto-
mm in lead alloys are sometimes extruded on matic billet feed called by the press during the
old vertical indirect extrusion presses over man- extrusion cycle and automatic removal of the ex-
drels and charged with liquid metal. These ex- truded semifinished product. Figure 5.5 shows a
trusion presses can have loads between 5000 and fully automatic plant with an integrated melting
15,000 kN. Cable sheathing with lead alloys is furnace and a chill mold billet casting machine.
carried out on special cable sheathing presses as Cored solders are hollow wire filled with flux
by a special tool during extrusion as shown in
Figures 5.6 and 5.7. The extrusion tool system
needed for the extrusion of hollow wire with flux
filling, which includes the die head with the hol-
low mandrel, the extrusion die, and the welding
chamber, and, in particular, their relative ar-
rangement is similar to that for cable sheathing.
Figure 5.6 depicts the construction of a die head.
The application of “transverse extrusion” com-
bined with “billet-on-billet” extrusion is an es-
sential requirement for the production of contin-
uous cored solder. Cored solder has, similar to
the cable sheath, both longitudinal and trans-
verse welds from this production method. The
billets are usually produced by the chill casting
process using casting machines and are normally
processed with the cast skin forming the billet
surface.
Fig. 5.4 Specific extrusion pressure in N/mm2 as a function Typical widely used solders are the soft sol-
of the stem displacement and the extrusion ratio V
⳱ A0/AS in direct extrusion of soft lead (Source: Siebal/Fang- ders L-PbSn40, L-Sn50Pb, L-Sn60Pb and L-
meier) Sn60PbCu2, the special soft solders L-SnCu3
200 / Extrusion, Second Edition
Fig. 5.5 Modern fully automatic extrusion plant for the production of soft solder with casting oven, chill mold billet casting plant,
hot-billet shear, and oil hydraulic 2500 kN extrusion press. The extrusion press is fitted with a fixed dummy block on the
stem. (Source: Collin)
Special soft solders need to some extent lower plant specification. The billet end faces are
the more difficult-to-extrude alloys’ higher de- sheared in a hot shear and thus cleaned of any
formation temperatures, which can be as high as oxide [Lau 76]. This is necessary to ensure per-
400 ⬚C. The container temperature has to be set fect transverse welds. After this operation the
correspondingly high to avoid excessive heat billets collect in a magazine in front of the con-
transfer between the billet and the container dur- tainer and fall one by one into the centerline of
ing extrusion. the press when the stem is fully withdrawn.
The wires are usually extruded to a diameter When the stem moves forward, the billet enters
of approximately 15 mm and then draw on the container and is pushed against the previ-
multispindle drawing machines to diameters be- ously extruded billet and the contacting material
tween 5 and 0.5 mm. The transverse and longi- volumes weld together. The extrusion emerging
tudinal welds formed in the welding chambers from the die is automatically fed into a multi-
of the extrusion die are able to withstand the spindle drawing machine and heavily reduced in
drawing deformation loads without any prob- diameter in one operation using a large number
lem. Good extruded surfaces are achieved by of drawing dies. The extruded wire usually
lightly lubricating the surface of statistically uni- passes through a water cooling system before
formly selected billets with a special lubricant. reaching the drawing machine.
The quantity applied of this lubricant must be
The production plan given subsequently for
controlled extremely accurately; otherwise, the
the manufacture of solder wire with a flux core
lubricant can enter the extrusion welds and pre-
(hollow solder) explains the solder wire manu-
vent perfect welding. The wires would then
break at the welds during drawing and have to facturing process in more detail.
be scrapped. Production of 1000 kg hollow solder with a
The extrusion process for the production of diameter of 0.8 mm from the soft solder L-
feedstock for solder wire commences with the Sn60Pb according to DIN 1707 filled with a flux
billet call from the extrusion press. The extruded of type F SW32 according to DIN 8511 with
wire passes continuously through a multispindle 2.5% by weight:
drawing machine in line with the press corre-
sponding to its capacity. The drawing machine 1. Casting in a chill mold casting machine or
controls the extrusion press. The billet is trans- heating of 168 billets with dimensions: 72
ferred either directly from the chill molding ma- mm diam. ⳯ 175 mm long (initial billet
chine as shown in Fig. 5.8 or from a billet mag- weight: 6.05 Kg) using an induction rapid
azine via an induction furnace, depending on the billet heating furnace to 50 ⬚C.
Fig. 5.7 Die holder, left, and hollow mandrel, right, as well as the front nut of the container with the pressure nut for adjusting the
hollow mandrel (See Fig. 5.6) (Source: Collin, Alchacht)
202 / Extrusion, Second Edition
2. Shearing of the billet end faces using the dou- 5. Drawing to: 1.35 mm diam. in one operation
ble shear visible in Fig. 5.5 during the trans- with 40 drawing dies on an intermediate
fer to the extrusion press. multispindle drawing machine
3. Extrusion into air with subsequent water 6. Drawing to: 0.8 mm diam. in one operation
cooling after the press—one extruded bar per with 40 drawing dies on a fine multispindle
extrusion with the dimensions 14.7 ⳯ 6.7 drawing machine.
diam. using the billet-on-billet process and 7. Coiling the wire on bobbins. This operation
transverse extrusion with simultaneous ad- is frequently combined with operation 6.
dition of flux using an extrusion tool system Quality control of the wire surface is also car-
shown in Fig. 5.6 from a container: 75 mm ried out.
diam. on a 2500 kN extrusion press—con- 8. Control and labeling
tainer temperature: 100 ⬚C; exit speed: 3.02
m/min; extrusion ram speed: 5.5 mm/s; ex- Solder threads are produced by multiple
trusion ratio V ⳱ 32.86. drawing of extruded solid wire approximately
4. Drawing to: 6 mm diam. in one operation 15 mm diam., depending on the final dimensions
with 14 drawing dies on a roughing multi- on the multispindle drawing machines and au-
spindle drawing machine. This drawing ma- tomatically cut transversely after drawing.
chine controls the extrusion press according The work hardening of the solder material
to the wire requirement via a dancing roll. produced during the cold working is countered
by the continuous softening from recrystalliza-
tion during the multispindle drawing process.
The process is helped by the heat of the drawing
lubricant in the sump of the drawing machine,
in which the entire drawing process takes place.
Soft solder usually recrystallizes at room tem-
perature following work hardening. Therefore,
intermediate annealing is not needed to achieve
the soft, i.e., recrystallized material, state re-
quired for further cold working.
copper improves the fatigue strength and mach- modulus of elasticity of pure magnesium is ap-
inability of zinc alloys. proximately 41,000 N/mm2 and that of magne-
Typical zinc-base extrusion alloys are sium alloys between 45,000 and 47,000 N/mm2,
ZnAl1Cu and ZnAl4Cu1. Bars, wires, tubes, and i.e., on average about 66% of that of aluminum
sections are produced from ZnAl4Cu1. The ma- alloys. Pure magnesium has a liquidus tempera-
terial can also be drawn. ZnCu is an alloy that ture of 650 ⬚C and crystallizes with a hexagonal
is used for the production of sections and hot- lattice structure. Metals with the hexagonal lat-
stamping components. Car tire valves are pro- tice structure can only slip on the (0001) base
duced from the alloy ZnAl15. plane at room temperature. Consequently, mag-
After hot rolling, extrusion is the most im- nesium alloys are very brittle at room tempera-
portant deformation process for zinc-base alloys, ture. However, temperatures above 200 ⬚C per-
although the main application of zinc alloys is mit the activation of other slip planes as well as
pressure die castings. The extrusion of these al- the formation of deformation twins enabling
loys has lost a lot of its importance. Zinc alloys these materials to be hot workable. The narrow
are extruded only to a limited extent mainly be- temperature range between the brittle and the
cause the limited workability associated with the plastic deformation behavior of magnesium al-
hexagonal lattice structure also affects the hot loys is of interest and is illustrated in Fig. 5.9
workability. Zinc alloys are extruded at defor- for the alloy MgAl6Zn [Sac 34, Bec 39].
mation temperatures of approximately 150 to Whereas this material clearly has a limited
300 ⬚C. Only very low extrusion speeds of ap- workability at 208 ⬚C as can be seen by the shear
proximately 3 to 6 m/min can be achieved be- stress cracks running at 45⬚, it can be readily hot
cause of the limited extrudability of the extruded worked at 220 ⬚C; i.e., a temperature increase of
materials at high specific pressures [Sac 34, Lau only 12 ⬚C produces significantly better defor-
76, Schi 77, Schu 69]. mation properties in this alloy. The formation of
twin lamellae is associated with the improve-
ment in the plastic workability.
Only magnesium alloys are used as structural
materials and in structural applications, the high
notch sensitivity has to be taken into account.
Extrusion of Materials with This also has to be allowed for in the cross-sec-
Deformation Temperatures tional geometry of extruded sections. In addi-
tion, magnesium alloys have a very elastic be-
between 300 and 600 ⬚C havior in compression because of their low
elastic moduli between 45,000 and 47,000 N/
Günther Sauer* mm2, but this also increases the sensitivity to
buckling.
Specific alloy additions can raise the static
and dynamic materials properties of magnesium
5.5 Extrusion of Semifinished by a factor of two or three. The principle alloy-
Products in Magnesium Alloys ing elements of the wrought alloys are aluminum
with contents up to 10 wt%, zinc up to 4 wt%,
Magnesium is a metal with the low density of and manganese up to 2.3 wt%. Zirconium, ce-
1.74 g/cm3, which is approximately 40% below rium, and thorium are also added. More recently,
that of aluminum. The densities of magnesium lithium has been increasingly used as an alloying
alloys fall in the range 1.76 to 1.83 g/cm3. The element.
Fig. 5.9 Deformation behavior of the magnesium alloy MgAl6Zn in hot-compression tests in the temperature range between 200
and 220 ⬚C (Source: Schmidt/Beck)
Aluminum is the most important alloying solutions with the phase MgZn. An addition of
element for magnesium, which forms a solid up to 3 wt% increases the fracture strength and
solution with aluminum at low contents and the fatigue strength of magnesium. Zinc contents
the intermetallic phase Al2Mg3 at higher con- more than 3 wt%, however, result in a drastic
tents. A eutectic occurs at 436 ⬚C at an alu- reduction in the elongation to fracture. Zinc con-
minum content of 32.2 wt%. Crystal segrega- taining magnesium alloys can be age hardened.
tions can occur in wrought alloys at aluminum This can increase the fracture strength of mag-
contents above 6 wt%. They can be dissolved nesium alloys by 30 to 40%.
and thus removed by homogenization of the Manganese dissolves in magnesium by, de-
cast in the temperature range of 400 to 450 ⬚C pending on temperature, up to 3.4% at 645 ⬚C.
for correspondingly long times. The solid-so- At this temperature magnesium forms a eutectic
lution formation at aluminum contents of 2 to with manganese. Manganese is dissolved by
approximately 6 wt% increase the fracture magnesium with the formation of solid solutions
toughness and hardness of magnesium alloys and the phase MgMn. It increases the strength
as shown in Fig. 5.10. At higher aluminum of magnesium at contents ⬎ 1.5 wt%. Manga-
contents, the fracture strength and, in particu- nese containing magnesium alloys have better
lar, the hardness can be further increased by corrosion resistance than other magnesium-base
the formation of the hard c phase, but with a alloys. Manganese contents of between 0 and
reduction in the ductility of the material as can
0.5% are therefore added to all magnesium al-
be clearly seen in Fig. 5.10 [Schu 69]. Mag-
loys to improve the corrosion resistance.
nesium-base wrought alloys have aluminum
contents up to 9 wt%. Magnesium alloys can Additions of zirconium form finely dispersed
be hot rolled at aluminum contents up to 7 zirconium oxides that act as the nuclei for a fine-
wt% and hot worked by extrusion at aluminum grain structure and thus increases the tensile
contents up to 9 wt%. The magnesium alloy strength of magnesium alloys with no reduction
becomes increasingly more brittle at aluminum in the elongation.
contents ⬎ 9 wt% as shown by the elongation Cerium also increases the fine-grain structure
in Fig. 5.10. This also shows that magnesium and improves the hot strength.
alloys with contents ⬎ 7 wt% can be age hard- Thorium improves the hot strength even more
ened after solution heat treatment. At the same than does cerium. This has resulted in the de-
time, the alloy suffers a drastic loss in ductility velopment of magnesium-thorium alloys with
[Schu 69]. particularly high resistance to softening. Tho-
Zinc readily dissolves, depending on the tem- rium also significantly improves the fatigue
perature, in magnesium by the formation of solid strength and specifically the creep strength [Tech
Fig. 5.10 The influence of aluminum on the mechanical properties of extruded magnesium alloys (Source: Spitaler)
Chapter 5: The Production of Extruded Semifinished Products from Metallic Materials / 205
96/97/98]. However, in England, alloys with centive to improve the existing alloys and to de-
more than 2 wt% of thorium are classified as velop new ones with the intention of:
radioactive. In the United States, use of mag-
● Improving the static and dynamic materials
nesium-thorium alloys is very restricted because
thorium-free magnesium alloys have been sub- properties, including elongation and tough-
stituted. ness
● Improving the temperature resistance
Magnesium alloys are very susceptible to
● Further reducing the density
corrosion compared with aluminum alloys be-
● The development of alloys with self-healing
cause they are electrochemically less noble. Ad-
ditions of nickel, iron, copper, and so forth pro- surface passive films
mote the corrosion of the material. Therefore, The coarse cast structure is transformed into
these additions are held in the range ppm by a fine grain elongated structure by hot working
using purer starting materials as well as im- in the extrusion process. This structural trans-
proved melt refining processes. This enables the formation is associated with a significant im-
corrosion sensitivity to be significantly reduced. provement in the mechanical properties of the
High-purity-based magnesium alloys today magnesium alloys in the same way as aluminum
have corrosion resistances comparable to alu- alloys. The mechanical properties that can be
minum alloys. achieved improve with increasing extrusion ra-
This has been one of the factors that has in- tio, i.e., with increasing working during extru-
creased the interest of the automobile industry sion. Figure 5.11 illustrates this process, which
in magnesium-base alloys and provided the in- is of considerable importance for the supply of
Fig. 5.11 Tensile strength RM and elongation to fracture A as a function of the extrusion ratio determined on single cavity extruded
round bars in the alloy MgAl10. Billets 175 mm diam were used for the experiments with a container diam of 180 mm
(Source: Beck)
206 / Extrusion, Second Edition
extruded semifinished products [Bec 39]. The wrought magnesium-base alloys in addition to
extrusion ratio V ⳱ A0/AS should not fall below those listed, particularly abroad, for example al-
5, and it is better to specify the minimum at 7. loys of the MgAl family. The working tempera-
A fine-grained extruded structure with good me- tures for extrusion are at 250 to 450 ⬚C, depend-
chanical properties can be achieved with extru- ing on the alloy and are higher than those used
sion ratios of 25 [Har 47]. for hot rolling the same magnesium alloys. Ex-
Magnesium alloys are mainly extruded using trusion ratios V ⳱ A0/AS similar to those for alu-
the direct extrusion process. Indirect extrusion minum alloys can be achieved. The extrudable
is possible and is used. Magnesium alloys flow magnesium alloys belong to the category of dif-
more uniformly in direct extrusion than do alu- ficult-to-extrude alloys mainly because of their
minum alloys. The discards can be reduced in hexagonal lattice structure. The extrusion speeds
thickness because of the lower distortion in the
fall in the range of moderate- to difficult-to-ex-
region of the billet surface and the resultant flat-
trude aluminum alloys. According to [Har 47],
ter dead metal zones in the deformation zone of
the container. Magnesium alloys can be welded the extrudability of magnesium alloys decreases
in the extrusion process. Therefore, porthole with increasing aluminum content as do the ex-
dies and bridge dies can be used to produce trusion speeds. Only the alloys MgMn and
tubes and hollow sections. Similar to aluminum MgMn2, as well as MgAl1Zn, can be extruded
alloys, large-diameter tubes are extruded over at speeds up to a maximum of 30 m/min [Zol
mandrels. It is also possible to use billet-on- 67]. The predominantly slow extrusion speeds
billet extrusion with magnesium alloys. How- naturally result in long extrusion cycles. There-
ever, the weldability is reduced by increasing fore, the extrusion container temperature has to
aluminum contents. be set so that the billet does not lose any heat to
Typical magnesium alloys for hot working by the container during the extrusion cycle; other-
extrusion are given in Table 5.2. There are other wise, the billet will freeze in the container. In
Table 5.3 Dependence of the specific extrusion pressure for the extrusion of tubes 44 ⴒ 1.5 mm in
the alloy MgAl3 on the homogenization treatment and the heating conditions of the billet 48 ⴒ 150
mm
Thermal treatment of the cast Heating before extrusion
before heating prior to extrusion Temperature, ⬚C Time, h Specific extrusion pressure, N/mm2
Not carried out 380–350 1 250–300
Not carried out 380–350 3 210–260
Not carried out 380–350 6 180–220
Not carried out 340–300 1 320–400
Not carried out 340–300 3 250–300
Not carried out 340–300 6 200–250
350 ⬚C–12 h 340–300 1 190–250
350 ⬚C–12 h 340–300 3 170–200
350 ⬚C–12 h 340–300 6 150–180
350 ⬚C–12 h 340–300 1 170–220
350 ⬚C–12 h 340–300 3 160–200
350 ⬚C–12 h 340–300 6 130–170
Source: Zubolob and Zwerev
addition, good soaking of the billet during heat- compared with aluminum alloys, even though
ing is required. Magnesium alloy extrusion bil- the formation of a layer cannot be avoided with
lets are normally extruded with the cast skin. magnesium alloys even when nitrided dies are
Heat treatment such as homogenizing im- used.
proves the hot workability of the magnesium- Cold working by drawing to improve the me-
base extrusion alloys. The effect of homogeni- chanical properties is practically impossible for
zation on the extrusion loads needed for hot wrought magnesium alloys because of their lim-
working of the alloy MgAl3 is shown in Table ited cold workability associated with their hex-
5.3 [Zol 67, Lau 76]. agonal lattice structure.
Extruded magnesium alloy semifinished Drawing in the form of a calibration draw is,
products exhibit extreme anisotropy because of however, of interest, as a means of improving
the hexagonal lattice structure of the metal. For tolerances.
example, tensile tests on extruded semifinished
magnesium alloys in the longitudinal direction,
i.e., the extrusion direction, have significantly
higher values for the 0.2% proof stress, tensile
strength, and elongation than in the transverse
direction. Extrusion of Semifinished
If the ratio of the tensile strength transverse/
longitudinal is taken as a measure of the aniso-
Products in Aluminum
tropy of a material, magnesium alloys have val- Alloys
ues in the range 0.6 to 0.7.
The nitrided dies used for the hot working of Rudolf Akeret*
magnesium extruded alloys have, in principle,
the same design features as those used for the
extrusion of aluminum alloys. Only the shape-
forming regions of the die are matched to the 5.6 General
specific properties of magnesium alloys by hav-
ing longer bearings and larger radii. The typical Of all the materials processed by extrusion,
hollow section die used for aluminum alloys can aluminum occupies the predominant role in
in principle be used for these alloys because of terms of both production volume and value.
their ability to weld during extrusion. In addi- Based on the annual volume of production of
tion, in contrast to aluminum alloys, magnesium primary and secondary metal, aluminum is
alloys have a significantly lower affinity for iron placed directly after iron. The majority are al-
alloys [Tech 96/97/98]. This property results in
a slower buildup of an intermediate layer of the *Extrusion of Semifinished Products in Aluminum Alloys,
extruded material on the die bearing surfaces Rudolf Akeret
208 / Extrusion, Second Edition
loyed to produce wrought alloys and formed into loys. Cold and hot extrusion with lubrication of
semifinished products of which 25% are ex- the container and the die is also used for bars
truded. The majority of all extrusion plants, and tubes [Ake 73].
three quarters in Germany, for example, process
aluminum alloys [Bau 82], 465,000 t in 1995.
The physical metallurgical properties of alu-
5.7 Extrusion Behavior of
minum alloys make them particularly suitable
for the extrusion of products very close to the Aluminum Alloys
finished shape and with attractive properties.
The face-centered cubic (fcc) structure with 12 5.7.1 Flow Stress
slip systems combined with a high stacking fault The extrusion temperature range, the flow
energy is a requirement for good cold and hot stress variations, and the friction across the tool-
workability. Corresponding to the melting point ing determine the extrusion behavior of alumi-
of 660 ⬚C, the hot-working temperature of alu- num alloys. Alloy and quality requirements de-
minum alloys falls in the range of 350 to 550 termine the necessary exit temperature for the
⬚C, which can be easily withstood by tools made extruded product and the temperature range for
from suitable hot-working steels. In this tem- the deformation. In the range 350 to 550 ⬚C, the
perature range the flow stress is reduced to val- flow stress of aluminum alloys is very dependent
ues that require relatively low specific press on the temperature and the composition [Ake 70,
pressures for processing. The natural oxide skin DGM 78]. The increase in the flow stress with
gives aluminum an attractive appearance and a increasing content of the most common alloying
good corrosion resistance in the natural state. In- elements is shown in Fig. 5.12 [Ake 70].
creased surface protection is given by anodic ox- The dependence of the flow stress on tem-
idation. Aluminum forms age-hardening alloys perature and speed is described in the context of
with low-alloying additions that combine good the basics of metallurgy in Chapter 4. Figure
hot workability with a high strength after a sim- 5.13 shows for some non-heat-treatable alloys
ple heat treatment. that reducing the temperature by approximately
Sections with an extensive range of function 100 ⬚C results in an almost doubling of the flow
specific cross sections can be extruded within stress providing the alloy additions stay in so-
narrow tolerances from aluminum alloys. Hol- lution [Ake 70].
low sections in the form of rectangular tubes and With age-hardening alloys similar to Al-
hollow engineering plates offer a high bending MgSi1 the variation of the flow stress is dis-
and torsional stiffness. The extensive variety of
aluminum sections used today in a wide range
of technologies is described in detail in
Chapter 2.
The selection of the extrusion process is
largely determined by the physical metallurgical
properties of the aluminum alloys. The high af-
finity to steel and thus the tendency to adhere to
all extrusion tools has to be included in the ma-
terial properties in addition to low extrusion
temperature and the good extrusion weldability.
Direct hot extrusion without lubrication and
without a shell is used for the majority of ex-
truded products, including solid and hollow sec-
tions from the easily and moderately difficult al-
loys. Direct extrusion can be used for practically
the entire spectrum of products, from the simple
round bar to complicated sections with a circum-
scribing circle close to the container cross sec-
tion. Flat dies are used for solid sections and
porthole dies for hollow sections.
Indirect extrusion comes into consideration Fig. 5.12 Increase in the flow stress of aluminum in hot
for compact cross sections in hard-to-extrude al- working with different alloying additions [Ake 70]
Chapter 5: The Production of Extruded Semifinished Products from Metallic Materials / 209
Fig. 13 Flow stress of some non-age-hardening aluminum alloys as a function of the deformation temperature (maximum of the
flow curve in torsion tests with u̇g ⳱ 0.655 sⳮ1) [Ake 70]
placed by solution and precipitation processes at a maximum immediately below the surface
according to the content of alloying elements in (Fig. 5.15) [Gat 54].
the matrix. A dead metal zone forms in front of the face
of the flat die. The surface of the extruded sec-
5.7.2 Flow Process
tion is not formed from the surface of the billet
The aluminum alloys are almost always ex-
truded in direct contact with the container and
die manufactured in hot-working steel. How-
ever, aluminum exhibits a significant chemical
affinity and adhesion tendency with iron [Czi
72]. Even in the solid state it tends to adhere to
tool surfaces. At face pressures above the flow
stress, Coulomb’s laws of friction lose their va-
lidity if the shear distortion of the peripheral
layer requires less force than the slip along the
surface of the harder frictional party [Wan 78].
The face pressure at the inner face of the con-
tainer is of the order of 10 times the flow stress.
Therefore, aluminum alloys flow in direct extru-
sion according to flow type B1 as shown in Fig.
5.14 [Val 96].
5.7.2.1 The Dead Metal Zone Fig. 5.14 Flow types B, B1, and C and the flow inward of
the billet peripheral layer along the dead metal
The billet surface is stationary relative to the zone (path 1) and from the dummy block edge into the interior
container inner wall, and the shear distortion is of the billet (path 2) [Val 96]
210 / Extrusion, Second Edition
but from the interior of the billet by shearing 5.7.2.2 In the Shape-Producing Aperture
along the dead metal zone [Ake 88, Lef 92]. The
The pressure conditions in the die aperture are
outermost layer of the billet surface initially ad-
heres to the inner wall of the container and is different. The axial pressure at the exit is zero,
or there can be a small tensile stress—if a puller
shaved off by the advancing dummy block. The
is used.
material that is compressed together in front of
the dummy block and that contains oxide and The face pressure, which determines the fric-
tion, cannot be easily calculated because it strad-
exudations from the billet surfaces ends up well
dles two boundary cases. If the section can slide
below the surface of the extrusion following the
path shown in Fig. 5.14, No. 2, and forms an as a solid body through the die aperture, the face
pressure, and thus the friction, is low. If the sec-
incompletely bonded intermediate layer referred
as the piping defect. Material located farther be- tion undergoes a reduction in thickness through
low the surface is compressed at the upper edge a narrowing die aperture, the face pressure is at
least equal to the flow stress. The large adhesion
of the dead metal zone and follows path 1 of the
affinity of aluminum increases the friction stress
dead metal zone into the region of the surface
of the extruded product. Adhesion of the mate- to the same order of magnitude as the shear
stress [Ake 88, Ake 85].
rial also occurs in feeder chambers and in the
ports of porthole dies where there is a high pres- The friction in the die opening is responsible
for the increase in the axial pressure against the
sure [Ake 88].
flow direction.
Slip with Coulomb friction is impossible in
the extrusion of tubes over a mandrel because of
the high radial pressure between the billet and
the mandrel. If the extrusion is carried out over
a stationary mandrel, relative movement with
shear friction takes place between the billet and
the mandrel from the start of extrusion over the
entire billet length. The relative speed is there-
fore of the order of magnitude of the stem speed.
The billet material is only accelerated to the exit
speed of the tube as it crosses the deformation
zone and at the same time the pressure on the
mandrel surface falls rapidly. The transition to
slipping friction of the finish extruded tube over
the mandrel tip takes place in the region of the
die aperture.
When a moving mandrel is used, the zone in
which relative movement occurs between the
billet and the moving mandrel is only the length
of the deformation zone. The shear zone moves
toward the back of the billet as the extrusion
progresses [Rup 82].
and partly removed in the emerging extrusion. mation zone, and the friction heats an even thin-
In the adiabatic limiting case, each MPa of av- ner surface layer of the section. A peripheral
erage extrusion pressure corresponds to an av- layer approximately one-third of the cross-sec-
erage increase in temperature of 0.3 K. tional area is therefore heated to a significantly
The magnitude involved is shown in Fig. 5.16 higher temperature than the core of the section
for the case of an easily extruded material with [Ake 72]. This temperature difference is very
a flow stress of 25 MPa in which a billet of short lived and is practically completely equal-
length l0 ⳱ 4D0 is extruded as quickly as pos- ized on the way from the die to the press platen.
sible with an extrusion ratio of 30 to avoid any Experiments with sheathed thermocouples in the
heat losses. When a material volume corre- die land have shown that the maximum surface
sponding approximately to the volume of the de- temperature can be 60 to 100 K higher than the
formation zone is extruded, there is initially a mean section temperature [Joh 96].
steep increase in temperature. With loss-free de- With sections, the maximum temperature,
formation, which approximately occurs in the which governs the onset of tearing, occurs dur-
core of the extrusion, the material is initially ing the passage through the die opening usually
heated by 25 K. at an edge where the longitudinal stress is the
The shearing of the material flowing through highest and the temperature probably at the max-
the deformation zone along the dead metal zone imum.
requires approximately the same amount of The possible working range of the press, i.e.,
work as the pure deformation [Ake 72, Sah 96]. the “window” in the temperature-speed field, is
An additional contribution, which cannot be ig- limited by the following thermal and mechanical
nored, is the friction in the die aperture, the mag- conditions:
nitude of which depends on the angle and the
● The surface temperature cannot exceed the
length of the bearings [Ake 85, Moo 96, Mue
maximum value that results in excessive
96]. The shear takes place in a surface layer ap-
scoring or even transverse cracks at any
proximately 10% of the diameter of the defor-
point (limit curve 1 in Fig. 5.17). The tem-
perature equalizes to some extent during the
crossing of the deformation zone.
● The average section temperature has to be
high enough to ensure adequate solution heat
treatment with AlMgSi alloys and to reduce nologies are influenced mainly by the need to
the tendency of AlCuMg and AlZnMgCu al- avoid defects that would impair the mechanical
loys to recrystallization (limit curve 2). properties or the decorative appearance [Bry 71,
● The press and its power source, on the other Fin 92, Par 96]. The following defects are par-
hand, determine the maximum extrusion ticularly important:
load and the ram speed. The latter decreases
● Uneven color tone (bands or flecks)
with increasing extrusion load (reduction in
● Coarse recrystallization
billet temperature) because of the increasing
● Excessive roughness (scoring or pickup)
slip loss (limit curve 3).
● Imperfectly bonded brittle contact areas be-
In the literature there are several different pro- tween material streams flowing together
posals for depicting the process limits [Joh 96, (piping, defective welds)
Hir 58, Ste 73, She 77]. ● Material separation in the form of transverse
The range of extrusion speeds that can be cracks, blisters, and flaking
practically obtained with aluminum alloys is ● Subsequent mechanical damage or corrosion
shown in Fig. 5.18 [Ake 71] plotted against the
flow stress at the extrusion temperatures used in The cause of these defects can be found in the
practice. structure of the billets, the flow process, and the
The exit speeds VA are scattered around a line extrusion temperature, in a subsequent heat
with a steep negative gradient that can be ap- treatment or defects in the logistics (handling,
proximated by the expression: transport, and storage of the finished sections).
To determine and eliminate the causes of
VA ⬃ kⳮ2 these defects, correct diagnosis and an accurate
f
knowledge of the process technological relation-
This empirical equation [Ake 68] can be ex- ships are necessary. The results obtained from
plained by the laws of heat penetration [Lag 72]. more accurate analysis of the flow processes and
the temperature field contribute significantly to
5.7.4 Section Surface and Surface Defects the understanding of these relationships. Men-
tion should also be made of the extrusion defect
In all stages in the production of aluminum catalog produced by the “extrusion” working
extruded sections, the plant and process tech- party in conjunction with the Institute for Ma-
terial Science of the RWTH Aachen University.
The peripheral layer therefore has a subgrain rium particles are nucleated on AlFeSi. Experi-
structure without defined grain boundaries, pro- ments on the etching kinetics have shown that it
viding the heat from extrusion or subsequent so- is these craters that have a strong effect on the
lution heat treatment does not result in static re- matte finish [Sta 90].The number of particles per
crystallization. This high deformation of the unit area depends on the average dendrite spac-
peripheral layer does not produce any higher ing (cell size) in the cast structure and also on
hardness in the as-extruded condition [Moe 75]. whether a region is normally elongated or highly
An additional feature of the highly deformed deformed during extrusion. The impoverished
peripheral layer is its 具001典 {211} shear texture, peripheral zones and the primary solidified re-
which differs from the 具111典 Ⳮ 具100典 double gions appear bright after anodizing, whereas the
fiber structure of the core zone [Moe 75, oxide skin and the segregation zones matte. The
Auk 96]. controlling factors for the frequency of nuclea-
Rows of precipitates are pulled apart by the tion of Mg2Si and AlFeSi are the temperature
extreme deformation and moved closer together changes during billet heat treatment and during
in the transverse direction so that the particles cooling or quenching after extrusion.
appear to be irregularly arranged. The recrystal- Pits form during etching along the grain
lization retarding effect of layers heavily deco- boundaries. The shape of the pits depends on the
rated with particles is then lost. This results in formation of the age-hardening b-MgSi phase.
undesired coarse grain recrystallization of the In general, different cooling conditions (influ-
AlCuMg and AlZnMg alloys, particularly at the encing the pit width) as well as different grain
end of extrusion where the peripheral layer size (influencing the pit length) can result in sig-
forms up to 90% of the cross section. nificant variations in brightness.
An orientation-dependent face etching occurs
5.7.4.2 Cast Structure and on the surface during etching and this consists
Anodizing Capability of small cube faces with an edge length less than
0.5 lm. The deformation texture of the section
Knowledge of the relationship between the lo- with the {011} 具211典 principle components can
cation of the volume element in the billet and in form to different extents in different parts of the
the section is the key to explaining and over- extrusion die. This results in an inhomogeneous
coming linear and banded tone variations in an- distribution of the cube faces and thus in differ-
odized sections [Ake 88, Bau 71, Lyn 71, ent reflection properties. This is how some of
Sta 90]. the undesired leg marks can occur.
The formation of the cast structure of the bil- Investigations on a hollow section [War 95]
let is discussed in Chapter 4, in the section on have shown that different die designs for the
metallurgical basics. From the point of view of same profile cross section can result in com-
the uniformity of the anodized surface, the fol- pletely different decorative appearances. Feeder
lowing regions of the billet surface are impor- chambers and splitting can affect the magnitude
tant: and direction of the local strain of the surface
● The oxide skin (10–100nm) layer. The die design therefore has a strong in-
● The segregation zone (up to ⬃600 lm) fluence on the texture, precipitate distribution,
● The impoverished peripheral zone and grain size.
● The periodic cold shut (up to several mm) The three mechanisms just described for the
● The columnar solidified crust (up to 15 mm) roughening of the surface (depressions, pits, tex-
● The primary solidified regions scattered over ture) have approximately equal importance for
the entire billet cross section the decorative appearance of the anodized sec-
tion. In addition, precipitates of the base metal,
Differences in the brightness of the oxide which can neither be dissolved nor removed dur-
layer are primarily caused by differences in the ing etching, end up in the oxide layer, giving it
number of depressions from the initial alkaline a cloudy or colored appearance.
etching. The etch attack does not occur uni- The external oxide skin in single-cavity ex-
formly but preferentially at all types of particles trusion follows path 2 (Fig. 5.14) and finishes in
at grain boundaries. The brightness is affected, the interior of the sections forming a brittle layer
in particular, by the depressions that form at all (piping defect). In multicavity extrusion, sec-
AlFeSi particles. Particularly deep craters de- tions with reentrant angles, and hollow sections,
velop at the locations where the Mg2Si equilib- the side adjacent to the center of the die consists
214 / Extrusion, Second Edition
Fig. 5.19 Highly deformed peripheral zone material (light) and normally elongated core material (dark) at the end of extrusion
[Ake 88a]
Chapter 5: The Production of Extruded Semifinished Products from Metallic Materials / 215
length and the angle of the bearing surface, the num nodules that adhere to the bearing surfaces
locally effective mechanisms of friction and form grooves on the section surface. The for-
wear of the surfaces of the section and die vary mation of layers of aluminum, which can be in-
along the die bearing. terspersed with oxide, increases the number of
The following possibilities have to be consid- adhesion points opposing the extrusion direction
ered, as shown in Fig. 5.20: [The 93]. The nodules are finally torn off with
● Slip of the section as a solid body with a the section and appear as particles (“pickup”) on
sudden speed increase at the steel surface the surface [Tok 88, She 88, The 93, Abt 96].
● Formation of a coherent layer of aluminum In the majority of cases, die bearing lengths
adhering to the bearing surface and slip of are less than the section thickness. If the bearing
the solid section with a sudden speed in- surfaces are parallel, mixed friction occurs over
crease between the section and the bonded the entire length. The surface roughness of the
layer extruded product is governed by the adhered
● Adhesion of the section peripheral layer on layer, i.e., by the tendency for the material to
the bearing surface, parabolic speed distri- adhere to the die [Mue 96, Mie 62, The 93]. This
bution across the section thickness adhesion tendency cannot be completely sup-
pressed by nitriding the bearing surfaces, but the
Slip exactly corresponding to “the first point” is aluminum layer builds more slowly on nitrided
not seen in hot extrusion of aluminum without die bearings. In the absence of lubrication, the
lubrication. aim for a high surface quality is not the maxi-
A friction “aⳭb” with adhesion of discrete mum possible undistorted slip of aluminum over
aluminum particles on the bearing surfaces cor- steel (slip process (a) in Fig. 5.20) but the most
responds most closely to the experience of die uniform buildup of a thin adhered layer of alu-
correctors and with the nitriding of bearing sur- minum on the die bearing surface. This aim is
faces. Microscopic investigations on split die in- best fulfilled by die bearings ground perpendic-
serts confirm that aluminum particles bond to the ular to the extrusion direction. Die surfaces
bearing surfaces to an increasing extent and size ground or polished parallel to the extrusion di-
in the extrusion direction and determine the mi- rection or polished favor an irregular buildup of
crogeometry of the section surface. The alumi- the adhered layer in the form of long elongated
and correspondingly wide and high ridges. Fig-
ure 5.21 [Tok 88] shows the roughness variation
over the length of a flat section on a small re-
search press.
The surface roughness of the extruded prod-
uct decreases as the bearing length increases be-
tween lk ⳱ 0 and lk ⳱ 1 to 3 mm because with
increasing back pressure the adhesive layer re-
gresses at the entry edge. As the bearing length
increases, the roughness increases again as a
consequence of higher temperatures [Wel 96]
and possible mechanical activation processes
[She 88] (Fig. 5.22). The optimum has been
found to be bearing lengths of the order of half
the thickness for flat sections [Mie 62, Tok 76,
Tok 88, She 88, The 93].
As the number of extrusions increases, the
fine aluminum nodules combine to form a layer
that ultimately completely covers the die bearing
surface. The relationship between the surface
roughness of the extruded product and the
buildup of the adhesive layer on the slip surface
is shown in Fig. 5.23 [The 93].
In the initial region 1, no aluminum adheres
Fig. 5.20 Velocity distribution transverse across the die ap- to the bearing surfaces so that section roughness
erture is governed by the surface finish of the die. In
216 / Extrusion, Second Edition
Fig. 5.21 Influence of the finish of the bearing surface on the quality of the section surface [Tok 88]
region 2, the aluminum adhesive layer builds up For a given billet temperature, the roughness,
and the section roughness increases rapidly. the degree of pickup, and the scatter of the gray
When the bearing has been completely covered, scale (as a measure of the degree of streaking)
dynamic equilibrium develops in region 3 be- increase to a maximum with increasing extru-
tween adhesion and tearing away of aluminum sion speed and then decrease at even faster
particles so that the surface roughness remains speeds. This is explained by the hypothesis that
almost constant. The section roughness is sig- at higher speeds the section surface slides over
nificantly lower than the roughness of the ad- a thin layer of almost liquid metal [Par 96].
hered layer. A reduction in the section roughness Alloy type, alloy content, and differences in
was periodically observed in trials involving 180 the thermal pretreatment of the billets can have
extrusions, and this was attributed to a partial or a significant influence on the extrusion speed
complete detachment of the coating. that can be achieved for given surface finish re-
The angle of the die bearing has a significant
influence on the friction force and results in a
different formation of the coating [Mue 96].
However, it has only a small influence on the
section roughness. Hand-filed bearing surfaces
close up at the entry and open up at the exit.
Mixed friction dominates on bearings that are
not too long, yet the changes in the face pressure
and the angle result in a different formation of
the coating. In the opening exit area loose ad-
hesions form and damage the section surface by
die lines and pickup [Clo 90].
As the billet temperature increases, the ten-
dency for adhesion between the section surface
and the bearing surfaces increases [Mie 62, Tok Fig. 5.22 Influence of the bearing length on the roughness
88, Clo 90]. Ra of the section surface [She 88]
Chapter 5: The Production of Extruded Semifinished Products from Metallic Materials / 217
quirements. Precipitates of alloying constituents remains in compression, but a tensile stress pre-
have the worst effect. vails in the peripheral zone. If this stress is too
low to produce plastic strain, the section can
5.7.4.4 Transverse Cracks and Peeling flow as a solid body through the die aperture
(Fig. 5.24a). Higher tensile stresses can result in
The tensile stresses produced in the peripheral an elongation of the hotter and at the entry
layer by the friction on the bearing combined slower flowing peripheral layer. This is seen par-
with the considerably higher temperature [Moo ticularly on thin ribs and internal legs of hollow
96, Joh 96] and the correspondingly lower flow sections (Fig. 5.24b). The elongation of the pe-
stress result in defects, which can penetrate deep ripheral layer after the removal of the dominat-
into the section from the surface. Figure 5.24 (a– ing high mean compressive stress in front of the
d) shows the qualitative variation in the velocity die results in various types of material defects,
and the stress at the entry to the die aperture. depending on the structure and the peripheral
The material being formed flows from the de- layer temperature. Lubricant residues that inad-
formation zone into the die aperture. The profile vertently have reached the inner wall of the con-
core flows faster than the surface section, which tainer can flow into the section following path 1
is retarded by the friction at the surface. The core in Fig. 5.14 and form an interface parallel to the
surface. The surface layer can break away dur-
ing extrusion (peeling) (Fig. 5.24c). In other
cases, the material of the interface can break up
during a subsequent heat treatment, and the sur-
face layer bulges out in the form of a row of
blisters. Peeling is also caused by the melting of
isolated eutectic regions resulting from unfavor-
able casting and homogenization conditions [Rei
84, Lef 96].
A classic defect process is the formation,
growth, and the amalgamation of voids resulting
in transverse cracks that penetrate deeply into
the section (fir tree) (Fig. 5.24d), The propaga-
tion and expansion of the cracks occur at the
location of the plastic elongation of the periph-
eral layer. At the same time the transfer of the
tensile stresses into the billet is prevented so that
less material flows into the peripheral layer. The
volume deficit in the peripheral zone is therefore
considerably larger than in the case of plastic
elongation as shown in Fig. 5.24(b).
In the common aluminum wrought alloys the
melting of individual structural regions, e.g.,
along grain boundaries, is the defect initiating
process (hot shortness). The transient exceeding
of the solidus temperature in the peripheral layer
is the most common cause of transverse cracks.
The average section temperature measured at the
exit is naturally well below the solidus tempera-
ture.
Another type of transverse crack that can oc-
cur well below the solidus temperature occurs in
materials with a high fraction (⬎15%) of non-
plastic brittle structural components.
5.7.5 Procedures to Control
the Thermal Balance
Fig. 5.23 Relationship between adhesive layer formation, As a general rule, the optimal productivity
friction stress, and surface roughness [The 93] and quality with aluminum alloys can only be
218 / Extrusion, Second Edition
achieved by taking the thermal balance of the perature below the desired average exit section
extrusion process into consideration. The tem- temperature. The material reaches the desired
perature control is optimized by measures that value only as it passes through the deformation
either reduce the amount of heat that has to be zone. This is described in detail in Chapter 3.
removed or accelerate the heat transfer [Ake 71, A uniform temperature gradient from the
Ake 80]. These measures have been described front to the rear of the billet can compensate
to some extent along with the extrusion process approximately for the increasing heat from the
(Chapter 3). The technicalities of temperature shear deformation of the peripheral layer. Ad-
control are described in more detail in Chapter 6. ditional heating of the front of the billet reduces
the load needed at the start of the extrusion pro-
5.7.5.1 Material cess and ensures that there is sufficient solution
heat treatment effect at the front of the section.
The heat produced during the extrusion pro- This method of achieving “isothermal extru-
cess from the transformation of the mechanical sion,” however, requires rapid localized heating
work can be minimized by selecting the most or cooling because of the good thermal conduc-
easily extruded alloy from those that meet the tivity of the aluminum. The billet then has to be
product specification (see the section ”Materi- extruded with minimum delay.
als”). In general, the effectiveness of the procedures
The additional fine adjustment covers the op- in this first group increases as the billet cycle
timization of the composition, the solidification time decreases, for example the extrudability of
conditions, and the thermal treatment of the bil- the alloy improves.
let. Small changes appear to result in consider-
able differences in the extrusion speeds that can 5.7.5.3 Heat Removal
be achieved [Ake 71, Sta 90, Rei 84, Sca 69,
Lyn 71, Lan 82, Spe 84, Lan 84]. The opposite applies to the following proce-
dures, which require heat flow into the tooling
and which are most effective for slow extrusion
5.7.5.2 Billet Temperature
speeds and long cycle times.
The exit temperature is higher than the billet Container. The most important heat sink is
preheat temperature because of the deformation the container, which plays an important role in
induced heating of the material being deformed; the productivity in the extrusion of aluminum
therefore, the billet is usually heated to a tem- alloys. The container is basically heated to a
Fig. 5.24 Influence of tensile stresses in the section peripheral layer. 1, appearance of the extrusion; 2, velocity variation across
the section; 3, variation of the longitudinal stresses across the section
Chapter 5: The Production of Extruded Semifinished Products from Metallic Materials / 219
temperature below that of the specified billet depending on the thickness and the coolant. This
preheat temperature. The temperature difference can be compared with the drive power of a press
is usually limited to 50 K in order to avoid the of up to 400 kW.
billet sticking in the container because of inade- The approximate calculations show that with
quate press power (“sticker”). The thermal bal- the fast extrusion of alloys with a high extrud-
ance in the system container-billet is described ability, only a small amount of deformation heat
in Chapter 3. can be removed through a cooled die. With a
The temperature set or recorded on the con- plate thickness of 50 mm, an aluminum flow of
tainer heater controller applies only to the hottest 1 kg/s can at best be cooled by approximately 6
location, where, from experience, overheating of K with water and by only approximately 2.5 K
the tool steel has to be avoided. The actual tem- with liquid nitrogen.
perature field in the container is shown in the A significant reduction in the exit temperature
example in Fig. 3.19. There are temperature dif- is achieved only with the slow extrusion of the
ferences of the order of 100 K in the axial and difficult-to-work alloys. In trials it has been pos-
radial direction. The temperature maximum sible to increase the exit speed of an AlCuMg
moves during 5 to 10 extrusions from the heat- alloy by 30% using water cooling. Approxi-
ing zone to the liner inner face [Ake 71, Ake 72, mately 15% of the deformation heat can be re-
Sch 79]. moved by the water cooling [Bat 79].
The cooling, i.e., the heat flow from the con- The limited resistance of the die materials to
tainer bore through the wall and into the atmo- temperature fluctuations makes water cooling of
sphere, is determined largely by the thermal con- a die difficult.
ductivity of the container wall. Cooling of the Liquid nitrogen is usually fed through chan-
mantle surface by an intensive air blast has only nels machined either in the die itself [Sca 79] or
an insignificant effect on the cooling. Blowing more commonly in the front face of the backer
onto the container end face has more effect. [Wag, Sel 84, Yam 92]. If a separate feeder plate
Today, combined heating and cooling systems is used, an additional network of cooling chan-
are installed in containers for temperature con- nels can be machined in the rear face so that the
trol (see the section on tooling in chapter 7). die is cooled from the front and the back [Ros].
Die. Removing excess deformation heat The aim is for the nitrogen fed in as a liquid
through the die is helped by the short thermal to evaporate extensively as it flows through the
path from the deformation zone to the location cooling channels. This gives an approximately
of the cooling channels. Another advantage is constant cooling capability, the effect of which
that the cooling takes place during the final stage is distributed over a more or less large aluminum
of the deformation so that the load requirement material flow, depending on the extrusion speed.
is increased only during the final deformation In experiments with nine different alloys, the
stage. There is also the possibility of specifically extrusion speed of AlMgSi0.5 could be in-
cooling the critical regions, e.g., at the edges creased by approximately 8% by cooling, but
prone to tearing. with the more slowly flowing alloy AlZn-
Because a significant amount of heat has to MgCu1.5, by a significant 80% [Sca 79].
flow through a relatively small die cross section, The dwell time of the deformation material in
it is necessary from the cooling point of view to the die region is short so that the peripheral zone
have an intense heat transfer to a coolant with of the section is cooled the most. This reduces
sufficiently large thermal capacity. the temperature peaks, which are largely respon-
This requirement is more easily fulfilled with sible for the tearing of the section surface at high
liquid coolants than gas. On this basis, the fol- extrusion speeds (Fig. 5.25) [Sel 84].
lowing methods can be differentiated for die This is the reason why even with limited cool-
cooling: ing effect the speed can often also be increased
●
considerably with fast-flowing alloys. The evap-
Water cooling
●
orated nitrogen emerges from behind the die ap-
Cooling with liquid-supplied evaporating ni-
erture onto the surface of the newly extruded
trogen
● Flushing with gaseous nitrogen
section to utilize the protective atmosphere ef-
fect (see below).
Approximate calculations demonstrate that Gaseous nitrogen is fed through channels in
the cooling capacity through a plate 200 mm in the gap between the die and the backer into the
diameter is in the range between 2 and 12 kW, space behind the die exit. The mass flow of the
220 / Extrusion, Second Edition
nitrogen stream is usually not more than 1% of application to the optimisation of the extrusion
that of the aluminum stream because of the low parameters will now be considered. Apart from
density. The nitrogen flow is therefore not suf- other limiting additional parameters the extru-
ficient to cause any serious cooling. sion parameters are at an optimum if the exit
The regularly observed improvement in the temperature over the entire cross-section falls
section surface must therefore be more attribut- within the permitted range for the alloy under
able to an influence on the dynamic equilibrium consideration, the extrusion speed is as high as
of adhesion and tearing off of the aluminum par- possible in the range limited by the equipment,
ticles on the die bearing by the reaction of the and the extrusion load needed uses the maxi-
newly formed aluminum surface with the at- mum press power of the press within a specific
mosphere. safety factor [Rup 77, Rup 77a, Rup 83].
Mandrel. In contrast to heavy metal extrusion The parameters that can be set at the press are
where cooling of the mandrel is unavoidable be-
the ram speed, the initial billet temperature, and
cause of the high thermal loading, in aluminum
the container temperature. The billet tempera-
extrusion, mandrel cooling is not required to
compensate for high temperatures. In practice, ture and speed can be constant for a heating and
mandrel cooling is therefore not used. However, extrusion cycle or be decreasing from the front
temperature measurements on the extruded pro- to the back and then be adjusted in subsequent
file have shown that the specific heat removed extrusion cycles.
by cooled mandrels is at least equal to that as- Of all the set parameters, only the extrusion
sociated with die cooling with liquid nitrogen so speed can be varied during a single extrusion
that it appears to be possible to achieve higher cycle. The billet temperature and the tempera-
maximum extrusion speeds by extruding over ture profile can, in contrast, be set for each cycle
cooled mandrels [Rup 82]. before loading into the press. A change in the
average temperature or the temperature profile
5.7.5.4 Optimization of the is possible in experimental work and under pro-
Extrusion Parameters duction conditions in the next billet. The tem-
Following the discussion of the different perature profile in the container with the usual
means of influencing the thermal balance their arrangement of heating elements in the container
mantle follows a change in the set temperature
only after a long delay of several hours. A rapid
change in the container temperature can be
achieved with heating and cooling systems in-
stalled in the liner [Har 94].
The parameter that has to be controlled is the
section exit temperature; however, there are nu-
merous difficulties in its continuous measure-
ment, particularly in the case of aluminum
alloys:
● The display of all temperature sensors is as- Special applications of joining in extrusion
sociated with definite delays and with sig- are cladding or locally reinforced sections of two
nificant measurement scatter. different materials (two aluminum alloys) (alu-
minum-copper, aluminum-steel), the compac-
The original concept of isothermal extrusion tion and deformation of powder and granular
assumed a continuous control of the speed based scrap, and the production of composite materials
on the measured exit temperature [Lau 60]. This with a metal matrix. This is described later in
concept is difficult to achieve because of the dif- this chapter.
ficulties mentioned previously, as well as the de-
layed response of the exit temperature to a
5.7.6.1 Extrusion Welding
change in the speed associated with the heat con-
tent of the material in the press. Changing the The general metallurgical principles of bond-
speed with a rapid reacting control system would ing by extrusion are discussed in Chapter 4. The
result in an unstable reaction in the control loop. following section describes how the extrusion
The control systems used or proposed and process relevant properties of the aluminum al-
tested today attempt to cope with these problems loys influence the technology of extrusion weld-
associated with exit temperature measurement in ing and the quality characteristics of the ex-
various ways. All these control systems are truded welds.
based on optimization concepts with the aim of Aluminum alloys can be extruded in a tem-
maintaining the exit temperature within the de- perature range at which the tooling is not over-
sired range by suitable combinations of the heated so that the stability and service life of
available parameters and simultaneously maxi- even complex hollow section dies are adequate.
mizing the productivity of the press. One factor The high adhesion affinity for steel results in
to take into account is that every change of one adhesive friction in the die at areas with high
parameter changes all heat sources and heat surface pressures and to the formation of dead
flows, i.e., the factors that combine to give the metal zones (Fig. 5.26).
exit temperature [Ake 80]. This is described in After only a short time in air, newly formed
more detail in Chapter 6. aluminum surfaces are coated with an oxide
layer that cannot be reduced by any gas atmo-
sphere or removed by diffusion of the oxygen
5.7.6 Joining by Extrusion into the parent metal. Aluminum therefore be-
The production of complex sections with one longs to the group of metals that cannot be
or more cavities plays a particularly important joined without macroscopic shape change, i.e.,
role in aluminum alloys. Approximately half the not by mere pressure and heat (diffusion weld-
sections produced in the easy to moderately dif- ing) [Jel 79, Bry 75].
ficult to extrude AlMgSi alloys are hollow sec-
tions such as box beams and hollow engineering
plates. Compared with the functional corre-
sponding solid sections (I-beams, plates with T-
shaped reinforcements) the hollow sections have
the advantage of a much higher torsional and
bending stiffness. With the exception of tubes in
the strictest sense, the hollow sections have lon-
gitudinal welds where the metal streams split by
the supporting legs of the mandrel reunite in a
metallic bond.
The joining of the metal from billets extruded
one after the other by transverse welds is used
for products in long lengths and large coil
weights. In addition, having a material residue
in the die entry or a feeder chamber provides
exact positioning of the front of the section,
which is essential for automation of the guiding
of the front end. The next billet has to join to Fig. 5.26 Laminar material flow [Ake 92]. 1, adhesive fric-
the residual material in the die. tion; 2, dead metal zone
222 / Extrusion, Second Edition
In order for two aluminum bodies to join in deviation processes (Fig. 5.27). In the first stage
the solid state, these brittle separating oxide lay- (Fig. 5.27a), the billet is divided into two or
ers require a significant combined deformation more streams that flow together under the legs
to break up the oxide skin and to bring nonox- (Fig. 5.27b, c). In the deformation final stage
idized metal to the joint. The generic term de- (Fig. 5.27d), the hollow section forms by the
formation welding includes roll cladding, com- metallic bonding of the streams.
posite impact extrusion, and powder extrusion, The processes at the contact areas are related
as well as extrusion welding. It is possible from to the material flow (Fig. 5.26). The conditions
observations of these processes using general on the exit side of the leg are critical where ei-
metallurgical basic principles to draw conclu- ther a dead metal zone or a cavity can form.
sions on the processes (previously studied only Normally, the pressure in the welding cham-
to a limited extent) that occur during bonding by ber is so high that the space under the legs is
extrusion. completely filled and a dead metal zone forms.
The influence of the initial unevenness of the The conditions for the formation of a dead metal
surfaces is also important [Ast 75]. The adhesion zone and for a good weld have been expressed
process is the result of the plastic flow of the by several authors in the form of ratios that can
metal in the contact zone, the deformation of the be deduced from the die geometry and provide
rough tips, the formation of slip and shear bands a reference point for the magnitude of the total
in the region of the contact surfaces, and the deformation. As well as the size of the welding
movement of the dislocation fields of the indi- chamber, the ratio of the welding chamber cross
vidual contacts. Uneven contact areas, however, section to the profile cross section is important
rarely occur in longitudinal welds and then in [Gil 75].
conjunction with cavities under the support legs The pressure applied at the point of formation
of the mandrel system. of the longitudinal weld is composed of com-
ponents for the reduction in cross-sectional area
5.7.6.2 Longitudinal Welds in from the welding chamber to the section, for the
deviation in the flow of the metal stream and for
Hollow Sections
overcoming the friction in the die aperture.
When applying these thoughts on deforma- Oxide can only enter the welding chamber
tion welding to extrusion welding, it is assumed with the first filling of the die when the free ox-
that the latter consists of three sequential extru- ide coated front faces of the streams meet (Fig.
sion processes and the associated transport and 5.28a) [Ake 92]. The fractured residues of these
Fig. 5.27 Extrusion of hollow sections. (a) Straight into the ports. (b) At an angle under the legs. (c) At an angle between two mandrel
heads. (d) Emergence of the section [Ake 92]
Chapter 5: The Production of Extruded Semifinished Products from Metallic Materials / 223
oxide films are largely removed with the front forming on the exit side of the leg (gas pockets)
part of the section (Fig. 5.28b). Further bonding [Val 95].
occurs between material regions that initially Two-dimensional numerical simulation and
have been upset in front of the legs and mandrels experimental semiplanar extrusion both showed
and have then flown along the flanks of the leg the formation of cavity with a section thickness
with severe shear distortion to collect in the dead of 25 mm and a dead metal zone with a section
metal zone under the legs. The streams that meet thickness of 12.5 mm for the same welding
together have no free surface and, therefore, no chamber height (Fig. 5.29) [Wel 95].
roughness and no oxide film. The welding pro- The contact with the leg is lost under the con-
cess then merely consists of the initially small ditions where a cavity is formed, and it is the
contact area being extended over the total length free more or less roughened surfaces of the
of the section and thus being enlarged by several streams that meet in the welding chamber.
orders of magnitude, whereby the subgrains also The bonding is then restricted to the rough
continuously reform over the original contact ar- crests [Val 95, Val 96], has little ductility, and is
eas. This repolygonization is associated with the above all very brittle [Ake 92]. Voids in the joint
movement of dislocations but does not require are recognizable in the fracture as bands without
diffusion of atoms. fracture dimples and they are preferentially
Die geometries where the cross section of the etched in the cross section by alkaline etchants.
material flow path is too narrow should be Transverse cracks can also occur in the region
avoided because these result in inadequate feed of the longitudinal welds. In principle these are
into the weld chamber and in an inadequate no different to the surface and edge cracks that
pressure buildup. This can result in cavities occur on solid sections when the peripheral layer
Fig. 5.28 Breakup of the surface layer in longitudinal welds. (a) Meeting under the leg. (b) Breaking apart. (c) Clean longitudinal
weld [Ake 92]
Fig. 5.29 Formation of a hollow space (gas pocket) under the mandrel support leg at a low extrusion ratio (a) and a dead metal
zone at a higher extrusion ratio (b). On the left, flow lines; right, lines of equal strain rate [Wel 95]
224 / Extrusion, Second Edition
reaches the hot-shortness temperature [Val 96a]. other than be pulled apart. In the most unfavor-
The fact that the transverse cracks occur pref- able case, there is no bonding [Ake 72], particu-
erentially next to the longitudinal welds can be larly with the current practice considered to be
attributed to the severe heating of the peripheral unavoidable of lubricating the dummy block and
layers of the metal streams, particularly under the discard shear [Joh 96a].
the legs [Ska 96]. With highly stressed sections, a length long
enough to contain the tongue of the transverse
5.7.6.3 Transverse Welds weld is removed as scrap from the stop mark.
This section usually includes one to two times
Transverse welds are usually the severely the content of the entry zones and the welding
curved surfaces where the material of the next chambers.
billet bonds with the residue of the previously In most of the transverse weld the fractured
extruded billet. This residue can be located in residues of the oxide layer are extensively pulled
the container, in the feeder chamber of a die for apart. These profiles can be supplied with the
a solid section, or in the entry ports of a hollow transverse weld for noncritical applications pro-
die (Fig. 5.30a–c). viding the material surrounding the tongues,
The process where the residue is left as a thick which originates from the previously extruded
discard in the container (Fig. 5.30a) is usually billet, can withstand the stresses from the
used for the extrusion of cable sheaths and elec- stretching of the section.
tric conductors in large coil weights. Special When the method of formation is considered,
measures have to be taken to avoid smearing of it is easy to understand that there is a greater risk
the contact surfaces. of transverse welds being impaired by surface
The process shown in Fig. 5.30(b) and (c) in coatings than longitudinal welds. When material
which the discard is removed in front of the separations apparently occur in longitudinal
feeder chamber or in front of the entry ports is welds, usually the transverse welds running
common for aluminum sections. Stripping of the along both sides are involved [Val 95].
discard (Fig. 5.30d) is also possible with alu- The most important sources of defects in ex-
minum but increases in difficulty with more trusion welds are [Wei 92]:
complex sections.
The originally flat contact surface between the ● Lubricant or corrosion on the dies
residue and the next billet is deformed to a ● Impurities on the billet front surface or dirt
tongue because of the adhesion of the aluminum on the billet surface
to the tool surface. The outline of the tongue ● Incorrect die design
approximates to the contour of the correspond-
ing material stream. In the region of the tips of Basically, all parts that come into contact with
these tongues the contact surface can contract by the material being extruded must be clean and,
as much as 50% so that the fractured residues of in particular, be free of oil, grease, or graphite.
the oxide layer are more likely to slip over each The requirement for perfect separation of the
Fig. 5.30 Extrusion of aluminum “billet on billet.” (a) Extrusion of a billet on the discard R in the container. (b) With feeder die. (c)
In the ports of a porthole die. (d) Pulling off the discard in a bridge die to avoid transverse welds [Ake 92]
Chapter 5: The Production of Extruded Semifinished Products from Metallic Materials / 225
dummy block and the discard, however, results rations and laminar enrichments of noncoherent
in practice in compromise solutions in which particles to be detected. For example, the
specific lubricants are considered to be indis- tongues of transverse welds can be localized. In
pensable but have to be used as little as possible fatigue studies the quality of the extrusion welds
and accurately applied. does not have a significant influence on the total
number of cycles but does on the rate of growth
of a crack in the extrusion weld at the end of the
5.7.6.4 Testing of Extrusion Welds
endurance.
The extrusion weld has to be considered as a Various Mechanical Tests. A critical me-
surface of which a fraction fD is covered with chanical test for extrusion welds requires that the
fragments of the original surface coating [Ake strain is reached at which failure will occur in
92]. The remaining fraction f1 consists of me- the parent material or in the weld. This critical
tallic ligaments with the same flow stress as the strain is strongly material dependent because the
parent material. These ligaments are very short energy released from the material separation
in relationship to their width and can therefore (“the damage potential”) grows with the square
withstand a high three-dimensional tensile stress of the elastic limit. Various technological testing
under tensile loading. procedures [Gil 75] enable the controlled trans-
In a tensile test perpendicular to an extrusion verse of strains that correspond in tensile tests
weld the specimen can completely neck outside approximately to the region of uniform elonga-
the weld. In the plastic region where the limit of tion up to fracture necking:
elastic deformation is exceeded many times
● Bending tests on samples taken transverse to
over, failure in the extrusion weld can still occur.
The concentration of fragments of the surface the extrusion welds. The limiting bending
coating on the contacting surfaces facilitates the angle is measured at a section dependent
damage with increasing deformation, i.e., the specified bending radius.
● Folding tests along and between the welds
formation, the growth, and the combination of
pores to form microcracks and, finally, failure. up to an internal radius ⬇0 and elongation
The usual parameters of 0.2% proof stress and of the outer surface of ⬇100%
● Axial compression of a tube section to the
the tensile strength from the tensile test have
limited relevance to the quality testing of extru- point of folding
● Bending of tubes with a roll bending system
sion welds. The increased sensitivity to damage
in the region of the extrusion weld compared under longitudinal loading of the extrusion
with the parent material is best expressed by a weld
● Expansion with a conical mandrel and mea-
decrease in the reduction in area at fracture. The
quicker the extrusion weld is damaged, the surement of the strain in the circumferential
lower is the strain to fracture [Ake 92]. With direction
decreasing extrusion weld quality, the elonga- These technological testing procedures are suit-
tion and, in the extreme case, the tensile able for following quality variations along and
strength, are also impaired as well as the reduc- between profiles with the same cross section and
tion in area. the same material and for monitoring the main-
Structural Investigation. Because the infor- tenance of tolerance limits that have been spec-
mation from tensile tests is limited, numerous ified for the individual application. However,
other testing procedures are used for testing the they do not supply any characteristic values that
quality of extrusion welds. The location of the could be used for numerical validation of the
longitudinal and transverse welds can be seen in safety of a design. The “calibration” of a tech-
the macrostructure. If a section is cut from an nological testing process from the point of view
extrusion at an externally visible interface be- of a fracture mechanics test value is still an un-
tween two billets, it is possible to identify from resolved problem.
the structure between neighboring transverse
welds whether sufficient material has been cut
5.7.6.5 Influence of the Extrusion Weld
out to achieve sound material. An extremely in-
tensive etch attack will reveal the inclusion of a on the Surface Appearance
lubricant or the peripheral layer. Although it is only a few atomic spacings
Ultrasonic Testing, Fatigue Investigations. thick, an extrusion weld can affect the appear-
Ultrasound enables both hidden material sepa- ance of the anodic film on a visible surface in
226 / Extrusion, Second Edition
billet heat treatment as a reversible fine disper- treatment costs and correction processes also in-
sion. The influence of manganese, in particular, crease with higher alloy contents.
is strongly dependent on the precipitate state and The heat treatment of age-hardening alloys
on the number and fineness of the intermetallic basically consists of the processes (see also
particles [Gru 66]. Intermetallic phases includ- Chapter 4):
ing Al6Mn, MnFeSi, Al3Zr, and FeAl3 reduce
● Dissolution of the alloying constituents
the extrudability significantly [Sca 67, Sca 69a].
● Quenching to retain in metastable solution
Figure 5.31 shows the product strength of the
● Age hardening, usually hot, in one or more
most common aluminum alloys as a function of
the flow stress at the extrusion temperature. temperature stages
The majority of extruded products therefore An important simplification is possible if the
are produced in heat treatable alloys with the product leaves the press with a temperature in
lowest possible alloy content. The desire to re- the region of solution heat treatment and can be
duce the magnesium content by a tenth or even immediately quenched to achieve the desired re-
a hundredth of a percent is due to the strong sult. This requires that the interval between the
influence of the flow stress on the cost of extru- solution temperature and the start of melting is
sion as well as the downstream processes. The greater than the unavoidable temperature error
extrusion load required is proportional to the and differences along the length of and across
flow stress as is the deformation work converted the section. In other cases an optimum solution
into heat. Another important consideration is heat treatment can be achieved only by a sepa-
that the time needed for this heat to penetrate rate operation in a very accurately controlled
into the tooling increases with the square of the oven. In this case, the material cannot be “press
flow stress, and the extrusion speed decreases quenched.”
accordingly. Apart from the dead cycle time, As the alloy content is reduced, the precipi-
which is largely independent of the material, the tation pressure decreases. The section does not
machine costs of the extrusion process alone in- have to be quenched so quickly but can be
crease to the cube of the flow stress. The heat cooled using less drastic means. This has the ad-
vantage that distortion resulting from excessive
localized temperature differences is avoided.
Thin AlMgSi0.5 sections can be adequately
cooled in static air or under fans. A more inten-
sive heat transfer is necessary for thick wall sec-
tions and higher alloy contents (e.g., Al-
MgSi0.7). This can be obtained with high air
velocities (nozzles) or air water mixtures (mist
nozzles) [Kra 93, Str 96]. The cooling require-
ments provide an additional material-dependent
cost factor partly related to the cost of the cool-
ing system but mainly because of the correction
costs that rapidly increase with increasing cool-
ing rate.
Because the extrusion load depends mainly on
the flow stress kf, the wrought aluminum alloys
are classified according to the flow stress into
the groups easy to extrude, moderately difficult,
and hard to extrude. Thus
The material behavior during plastic working curve is a material parameter for the ideal defor-
can be derived from high-temperature torsion mation and depends on the working temperature
flow curves. These show the deformation load kf and, in particular, the rate of deformation.
as a function of the logarithmic principal strain Figure 5.32 shows the torsion flow curves for
u. It should be emphasized here that the flow the extrusion alloy AlMgSi0.5 at 450 ⬚C and a
logarithmic strain rate of du/dt ⳱ 0.1 sⳮ1 as a and AlMgSi0.7, are considered to belong to the
function of the logarithmic principal strain ug easily extruded alloys. Because AlMg1 and
between 1 and 7.5. AlMgSi0.5 are frequently used for anodizing or
The flow stress of the most important extru- bright finish applications, care must be taken to
sion alloys is shown in Table 5.4 at a logarithmic ensure that the Mg and Mg2Si components are
principal strain of ug ⳱ 2.7. This corresponds dissolved in the solid solution in the as-extruded
to an extrusion ratio of 15:1. The kf values listed state. Also, none or, if necessary, very small ad-
illustrate the different deformation properties of ditions of insoluble or supersaturated dissolved
the individual extruded alloys. These were ob- elements such as manganese, chromium, zirco-
tained from torsion flow curves taken from both nium, or iron may be used. For this reason,
the DGM Atlas of Hot-Working Properties, Vol- AlMg1 and AlMgSi0.5 are produced from a
ume 1 [DGM 78], and internal investigations at base metal of a higher purity for bright finish
VAW Aluminium, Bonn, Germany. qualities. In DIN EN 573-3 the individual alloys
The aluminum alloys are designated below by are shown based on 99.85, 99.9 and 99.98 Al. If
the chemical symbols, which was the custom un- this is not taken into account, secondary precip-
til recently. Table 5.5 compares the material des- itates can form during billet heat treatment and
ignation of the old DIN 1712 T and 1725 T with these can impair the surface quality of the ex-
the new DIN EN 573-3. truded sections by streaking.
The billet heat treatment—referred to as
5.8 Easily Extruded Alloys homogenization—of AlMg1 is mainly to reduce
crystal segregation and dendritic residual melt-
Alloys with low kf values (kf ⱕ 30 N/mm2)
are usually classified as easily extruded. To a
first approximation, the lower the required flow
stress the better is the workability. Normally the Table 5.5 Comparison of the aluminum alloys
possible exit speed increases with the workabil- according to DIN and DIN EN
ity [Ake 68]. DIN 1712 T3/DIN 1725 T1 DIN EN 573–3(a)
Symbol Symbol No.
5.8.1 Aluminum Alloys
Easy-to-extrude alloys
In addition to aluminum, the naturally hard Al99.5 Al 99.5 1050A
alloys AlMg1 and AlMn1, as well as AlMgSi0.5 Al99.8 Al 99.85 1085
Al99.98R Al 99.98 1098
E-Al E Al 99.5 1350
AlMg1 AlMg1 5005A
Table 5.4 Flow stress of different aluminum AlMn1 AlMn1 3103
alloys AlMgSi0.5 AlMgSi 6060
AlMgSi0.5 AlMg0.7Si 6063
Experimental material: homogenized cast billets. Test: torsion
AlMgSi0.7 AlSiMg 6005A
flow curves; test temperature 450 ⬚C. Logarithmic principal
strain ug ⳱ 2.7; deformation rate (log principal strain rate) Moderately difficult-to-extrude alloys
u̇g ⳱ 0.1 sⳮ1
AlMg2.5 AlMg2.5 5052
DIN EN 573-3(a) AlMg3 AlMg3 5754
AlMg1Mn1 AlMn2Mg1 3004
Symbol No. Flow stress kf, N/mm2
AlMg2.7Mn AlMg3Mn 5454
Easy-to-extrude alloys AlMgSi1 AlSiMgMn 6082
Al99.5 1050A 17.9 AlMgSiCu AlMg1SiCu 6061
AlMgSi 6060 19.8 AlMgSiPb AlMgSiPb 6012
AlMn1 3103 23.6 AlZn4.5Mg1 AlZn4.5Mg1 7020
AMg1 5005A 28.2 AlCuLi(b) AlCu2LiMg1.5 2091
AlLiCuMg1(b) AlLi2.5Cu1.5Mg1 8090
Hard-to-extrude alloys
Hard-to-extrude alloys
AlSiMgMn 6082 41.5 AlMg5 Al Mg5 5056A
AlMg3Mn 5454 43.8 AlMg4.5Mn AlMg4.5Mn0.7 5083
AlZn4.5Mg1 7020 44.2 AlCuMg2 AlCu4Mg1 2024
Difficult-to-extrude alloys AlCuSiMn AlCu4SiMg 2014
AlCuMgPb AlCu4PbMgMn 2007
Al4.5MgMn0.7 5083 46.7 AlCuMgFeNi(b) AlCu2Mg1.5Ni 2618
AlCuMg2 2024 48.2 AlZnMgCu0.5 AlZn5Mg3Cu 7022
AlCuMgFeNi 2618 51.5 AlZnMgCu1.5 AlZn5.5MgCu 7075
AlMg5 5056A 55.9 AlZn8MgCu(b) AlZn8MgCu 7049A
AlZn5.5MgCu 7075 56.3
(a) The prefix “ENAW” has been omitted from the DIN EN 573-3 designations.
(a) The prefix “ENAW” has been omitted from the DIN EN 573-3 designations. Al99.5 is ENAW-Al99.5; 1050A is ENAW-1050A.
A199.5 is ENAW-A199.5; 1050A is ENAW-1050A. (b) Not standardized in DIN
230 / Extrusion, Second Edition
ing and to produce an easily worked cast struc- a smooth billet surface goes hand in hand with
ture. In contrast, in AlMn1 the manganese exits the improvement of the internal structure. A
in a supersaturated solid solution. This nonequi- fine-cellular dendritic cast structure with little
librium state is activated by the thermal treat- variation in the cell size across the billet diam-
ment and tries to attain equilibrium by the for- eter is desired [Sca 78] (see also the section
mation of secondary precipitates. The size of the “Melting and Casting Processes” in Chapter 4).
precipitated particles depends on the tempera- During the billet heat treatment (homogeniz-
ture and the heat treatment time. The higher the ing), the plasticity of the cast structure can be
temperature and the longer the heat treatment significantly improved. This occurs by the re-
time, the coarser are the particles. It is known duction in grain segregation and the formation
that the degree of dispersion influences the re- of the intermetallic AlFeSi cast phases during
crystallized grain structure and the workability. the billet heat treatment just below the solidus
It is therefore important with AlMn1 to heat treat line. These effects are the more marked the finer
at a high temperature of 590–620 ⬚C in order to the dendritic structure of the cast billet because
produce a fine grain during extrusion. the initial conditions are then more favorable for
The most common easily extruded alloy is the thermally activated processes.
AlMgSi0.5. It differs from the materials de- The billet heat treatment cycle involves not
scribed so far in that it achieves its properties by only the heat treatment temperature of 560–580
age hardening. AlMgSi0.5 is characterized by ⬚C and the holding time of 6 to 8 hours, but also
good mechanical properties as well as by out- the heating and cooling of the billets. The rate
standing workability combined with an excellent of heating is not limited for any metallurgical
surface quality. reasons. With AlMgSi0.5, rapid cooling from
As already mentioned, the temperature range the heat treatment temperature is recommended
for the hot-working process coincides with that because with slow cooling (ⱕ 50 K/h), the
for solution heat treatment. In this case, separate Mg2Si is precipitated in a coarse format. With
solution heat treatment and quenching of the ex- rapid billet heating to the extrusion tempera-
truded section—as required for the high-strength ture—in an induction furnace—the heat treat-
materials—is not required. ment time can be too short to redissolve the
AlMgSi0.5 extruded sections only need to be coarse particles. This reduces the mechanical
cooled with moving air because of the low properties after age hardening. In addition,
quench sensitivity in order to retain the age- coarse precipitates reduce the surface quality,
hardening phase Mg2Si in ␣-solid solution. A particularly in anodizing.
characteristic of this alloy is that Mg2Si can be
5.8.2 Extruded Products
retained in supersaturated solution with a cool-
ing rate of only 2 K/s. The desired increase in Extruded products are classified as bar, tube,
strength can be obtained by subsequent cold or and extruded sections and are standardized in
warm age hardening. DIN 1746, 1747, and 1748 (See The Aluminum
The important requirements for AlMgSi0.5 Association, ANSI H35.1).
and AlMgSi0.7 type alloys are small fractions The range of profile cross sections is almost
of the principle alloying elements dissolved in inexhaustible for the easily extruded aluminum
the ␣-solid solution at the press exit temperature alloys. Profiles with asymmetric cross sections
and the avoidance of large additions of the re- and considerable wall thickness variations can
crystallization retarding elements of manganese, be produced. Reference should be made to
chromium, and zirconium because, in the form Chapter 2, which covers the wide range of ap-
of fine secondary particles, these significantly plications.
increase the flow stress and thus reduce the ex- Aluminum and the easily extruded AlMgSi
trudability. In addition, they act as foreign nuclei types also have excellent extrusion welding
for the age-hardening phase. Mg2Si is deposited properties. Hollow sections can therefore be pro-
at the Al(Mn,Fe)Si containing crystals and in duced with extruded longitudinal welds using
this form can no longer contribute to the age special dies (bridge, porthole, and spider dies).
hardening [Sca 64]. The wall thickness that can be held with ex-
The quality of the continuously cast billets has truded sections is determined by the following
a not insignificant influence on meeting the high parameters:
quality and productivity requirements of the ex- ● Material
trusion plant. It is known that the formation of ● Specific pressure
Chapter 5: The Production of Extruded Semifinished Products from Metallic Materials / 231
With alloys that do not age harden, the exit nomic point of view because higher extrusion
temperature and the rate of cooling of the ex- speeds are achieved with lower extrusion tem-
truded section are not critical for the mechanical peratures. This, however, conflicts with the met-
properties. Nevertheless, cooling with fans is allurgical requirement of the exit temperature
recommended for economic reasons and to pre- ⱖ500 ⬚C in order for the age-hardening phase—
vent precipitation and grain growth. The guide- in this alloy family approximately 1% Mg2Si—
lines for the extrusion parameters discussed for to dissolve in the ␣-solid solution. If this does
the individual alloys are given in Table 5.7. not occur, the section cannot be age hardened to
In the production of extruded sections in the the desired values.
age-hardening alloys AlMgSi0.5 and Al- The exit temperature depends on the opti-
MgSi0.7, the combination of special metallur- mized flow stress of the material produced by
gical and process technological measures en- the billet heat treatment, the billet temperature
ables not only the economic production of and the heating conditions before extrusion, the
complicated profile cross sections but also si- extrusion ratio, and the rate of deformation.
multaneously the attainment of favorable me- The billet heating in an induction oven re-
chanical properties. This is possible because quires approximately 4 to 6 minutes. This is sig-
with these alloys the temperature range for hot nificantly faster than a gas-heated continuous
working and solution heat treatment largely co- oven where approximately 45 to 50 minutes are
incide. A further positive characteristic of these needed. These differences influence the diffu-
alloys is that the age-hardening phase Mg2Si can sion-controlled solution processes. It is easy to
be retained supersaturated in solution even with understand that rapid heating of the billet before
a cooling rate of only about 2 K/s and the me- extrusion is advantageous where rapid cooling
chanical properties subsequently improved by from the billet heat treatment temperature pre-
precipitation during age hardening. vents the formation of coarse Mg2Si particles. If
It is important to set the process parameters preheating is carried out in a gas-fired continu-
to meet both the metallurgical and production ous furnace, then the opposite applies because
requirements. In many cases a compromise has the cooling from the billet heat treatment does
to be found. The exit temperature is determined not play the decisive role.
by two opposing criteria. The lowest possible It should be pointed out here that in the United
exit temperature is needed to obtain a smooth States in particular, one method of operation is
surface finish. This is also desired from an eco- to heat the billets to a temperature above the
Table 5.7 Typical values for billet high-temperature heat treatment and extrusion conditions of
aluminum alloys
Alloy Homogenization, ⬚C Holding time Preheat, ⬚C Container temperature, ⬚C Typical exit speeds, m/min
Al99.8–99.99 580–600 6 380–450 330–350 50–100
AlMg1 530–550 6 400–460 350–380 30–70
AlMn 590–620 12 400–460 350–400 30–70
AlMgSi0.5 560–580 6 450–500 400–450 30–80
AlMgSi0.7 560–580 6 470–510 420–450 25–65
AlMg2.5 520–540 6 430–490 360–380 5–15
AlMg3 510–530 6 460–490 360–380 5–15
AlMg1Mn1 540–560 16 450–500 380–400 10–30
AlMg2.7Mn 510–530 16 480–510 380–400 10–20
AlMgSi1 480–570 12 500–540 400–420 15–35
AlMgSiCu 540–570 12 500–540 380–400 10–40
AlMgSiPb 470–480 12 450–530 400–420 10–30
AlZnMg1 460–480 12 420–480 370–430 10–40
AlCuLi 520–550 12 400–450 350–400 5–25
AlLiCuMg 520–550 12 400–450 350–400 5–20
AlMg5 500–520 12 440–480 360–410 1.5–3
AlMg4.5Mn 500–520 12 430–480 410–430 2–5
AlCuMg2 480–490 12 400–460 370–400 1.5–3
AlCuSiMn 475–485 12 400–460 380–400 1.5–3
AlCuMgPb 450–480 12 380–440 360–400 1.5–3
AlCuMgFeNi 520–530 24 400–440 360–380 1.5–3
AlZnMgCu0.5 475–485 12 420–480 360–410 1.5–3
AlZnMgCu1.5 475–485 12 420–480 360–410 0.8–2.5
AlZn8MgCu 475–485 12 420–480 360–410 0.8–2.5
Chapter 5: The Production of Extruded Semifinished Products from Metallic Materials / 233
subsequent extrusion temperature to achieve The extruded sections are finally stretched by
complete dissolution of the Mg2Si phase. The 0.5 to 1.5% to achieve the straightness specified.
billet is cooled outside the oven to the desired The final operation after cutting to the fin-
lower production temperature before extrusion. ished length is age hardening. With the AlMgSi
Higher mechanical properties can then be alloys, the mechanical properties are usually
achieved [Sca 64, Rei 88]. reached after 4 to 12 hours at 160–180 ⬚C, de-
As mentioned previously, a wide range of ex- pending on the selected temperature (Table 5.8).
trusion ratios from V ⳱ 20 to V ⳱ 100 can be Preaging at room temperature has a favorable
used for the easily extruded alloys. The selection influence on the properties that can be achieved
usually depends on the container diameter. From with alloys with low contents of the main alloy-
the point of view of the grain formation, it can ing elements [Dor 73].
be advantageous to change to higher extrusion
ratios because the recrystallized grain size de-
pends on the degree of deformation as well as 5.9 Moderately Difficult Alloys
the temperature.
Obviously, the deformation rate should be as Aluminum alloys with flow stresses ⬎30 to
high as possible for economic reasons. High de- 45 N/mm2 are classified as moderately difficult.
formation rates are also desired for metallurgical The relative extrudability of these alloys in this
reasons because the deformation temperature category is only 40 to 60% of AlMgSi0.5 if the
has a significant influence on the exit tempera- extrudability of this easily extruded alloy is set
ture, which in turn determines the hardening be- at 100% [Hon 68]. This reduction is due to the
havior. Limiting factors are again the specific increase in the main alloying elements, which
pressure (stem load over the container cross-sec- are added for alloy technical reasons to increase
tional area) and the roughening or tearing of the the material properties as well as the addition of
section surface. The effect of die cooling with manganese to produce the desired hot-working
nitrogen can be found in section 5.7.5.3. structure.
As a guideline, exit speeds of 30 to 100 m/
min can be expected with AlMgSi0.5, depend-
ing on the degree of difficulty. With AlMgSi0.7, 5.9.1 Aluminum Alloys
the values are approximately 15 to 20% lower The naturally hard materials include the
because of the higher amounts of magnesium AlMg alloys with higher magnesium contents as
and silicon, as well as small manganese addi- well as the AlMgMn alloys. The magnesium
tions. contents vary between 1.8 and 3% and the man-
Immediately after leaving the press, the sec- ganese content between 0.3 and 0.8%. The billet
tions are cooled with air or an air water mist heat treatment temperature has to be lowered
mixture to a temperature ⱕ200 ⬚C. This proce- compared with the easily extruded alloys AlMg1
dure avoids deformation or twisting of the sec- and AlMn to avoid melting because the solidus
tions. A cooling rate of 2 K/s is sufficient to line in the phase diagram has a strong tempera-
retain the Mg2Si in solid solution. ture dependence (Table 5.7).
Table 5.8 Typical values for heat treatment of age-hardening aluminum alloys
Quenching at the press Separate heat Cooling Age-hardening
Material Temper(a) exit temperature, ⬚C treatment, ⬚C method temperature/time
AlMgSi0.5 T5 ⱖ 500 ... Moving air 160–180 ⬚C/12–6 h
AlMgSi0.7 T5 ⱖ 510 ... Moving air 160–180 ⬚C/12–6 h
AlMgSiCu T5 ⱖ 520 ... Moving air 160–180 ⬚C/12–6 h
AlMgSiPb T5 ⱖ 520 ... Moving air 160–180 ⬚C/12–6 h
AlMgSi1 T6 ... 530–540 In water ...
AlCuMg2 T3 ... 495–502 In water ...
AlCuMgPb T4 ... 480–485 In water ...
AlCuSiMn T4 ... 500–505 In water ...
AlCuMgFeNi T6 ... 525–535 In water ...
AlZn4.5Mg1 T5 ⱖ 460 ... Air 185–195 ⬚C/18–20 h
AlZnMgCu0.5 T6 ... 475–480 In water 90 ⬚C/10–12hⳭ120 ⬚C/18–20 h
AlZnMgCu1.5 T6 ... 475–480 In water 90 ⬚C/10–12hⳭ120 ⬚C/18–20 h
AlZn8MgCu T6 ... 475–480 In water 120VC/20–24 h
(a) Material temper condition according to DIN EN515
234 / Extrusion, Second Edition
The heat treatable materials that belong to the truded structure, particularly in the direction of
moderately difficult alloys include the alloy extrusion [Die 66]. The formation of a coarse
AlMgSi1 that is frequently used in Germany and grain recrystallized peripheral layer and an un-
the alloy AlMgSiCu preferred in the United recrystallized core is well known in these alloys
States, the free-cutting alloy AlMgSiPb and the after age hardening.
readily weldable alloy AlZn4.5Mg1, as well as The same observations are made in the cop-
the more recent lithium-containing alloys per-containing AlMgSi alloy where manganese
AlCuLi and AlCuMgLi. is partly replaced by chromium, which metal-
AlMgSi1 does not only differ from the lurgically functions in a similar way. The low-
AlMgSi0.5 alloy in the higher Mg2Si content but copper addition favorably affects the grain for-
also in the addition of about 0.4 to 1.0% man- mation and the mechanical properties as well as
ganese. From the metallurgical point of view, the general corrosion resistance [Sca 65].
this results in the recrystallization temperature Both the alloys AlMgSi1 and AlMgSiCu are
being increased to a significantly higher tem- significantly more quench sensitive than Al-
perature and higher strain. It is important to note MgSi0.5 because of the manganese addition.
that both the manganese dissolved in the ␣-solid Sections in these alloys have to be rapidly
solution as well as the precipitated manganese- cooled immediately after extrusion with a water
containing phases have a recrystallization re- mist or in a standing water wave. A separate
tarding effect and increase the deformation re- solution heat treatment with water quenching is
sistance. The size of the manganese-containing recommended with thick-walled tubes and bars
phases can be controlled by the temperature of to maintain the strength and the toughness. The
the billet heat treatment [Sca 69a] (see also the manganese-containing phases of the order of
section “Extrudability of Metallic Materials” in 0.05 to 0.7 lm obtained from low-temperature
Chapter 4). Coarse particles that form at a tem- billet heat treatment and which are uniformly
perature of 560 to 580 ⬚C have a lower recrys- and densely distributed in the matrix have a
tallization retarding effect than fine particles that positive effect on the toughness behavior [Sca
are produced at a heat treatment temperature of 82]. The particle arrangement described dis-
460 to 480 ⬚C. places the fracture from the grain boundary into
AlMgSi1 extruded sections do not have a re- the matrix by cavity formation. Manganese-con-
crystallized grain structure like AlMgSi0.5 be- taining AlMgSi alloys therefore are less suscep-
cause of the recrystallization retarding effect of tible to intercrystalline facture and thus have sig-
the manganese additions but an elongated hot- nificantly higher toughness values.
worked structure with deformation texture com- Another moderately difficult-to-extrude alloy
ponents (Fig. 5.33). This formation of the grain that should be mentioned is AlZn4.5Mg1. Me-
structure is referred to as the extrusion effect. It chanical properties even higher than AlMgSi1
is characterized by an increase in the mechanical can be achieved and a structure with the extru-
properties over those of the recrystallized ex- sion effect is also needed for this alloy to achieve
high mechanical properties. Figure 5.34 shows
that only a small recrystallized fraction is to be
expected if the billet heat treatment is carried out
at 460 to 480 ⬚C and the extrusion ratio is not
high. With this alloy a higher billet heat treat-
ment temperature should not be used as other-
wise recrystallized grains occur, and there is a
tendency toward stress-corrosion cracking
(SCC), and the values in the standard are not
reached [Sca 73].
AlZn4.5Mg1 is characterized by a signifi-
cantly lower quench sensitivity than AlMgSi1.
Maintaining a cooling rate of 0.5 K/s is not only
recommended for process technology reasons
but has to be held for metallurgical reasons to
avoid SCC.
Fig. 5.33 Extruded section (extrusion effect with thin recrys-
Since the middle of the 1980s, intensive at-
tallized peripheral zone) of an AlMgSi1 bar (cross
section, Barker anodized, micrograph in polarized light) tempts have been made worldwide to develop
Chapter 5: The Production of Extruded Semifinished Products from Metallic Materials / 235
new aluminum alloys with improved materials tion. With extended age-hardening, this results
properties. The specific aims for the aerospace in an increase in the elongation to fracture with
industry are a higher component stiffness and a simultaneous increase in the flow stress.
weight reduction. Lithium was considered as an Mechanical property variations across the
alloying element because of its density of only cross section are found in lithium-containing al-
0.534 g/cm3 and because it is one of the few loys because of the nonuniform texture forma-
elements that increase the modulus of elasticity tion [Tem 91].
of aluminum alloys. In addition, the Al-Li phase
diagram shows a temperature-dependent solu-
bility so that the requirement for an increase in 5.9.2 Extruded Products
strength by age hardening is also fulfilled [Web With their outstanding corrosion resistance to
89]. seawater, the naturally hard alloys are particu-
Age-hardening lithium-containing alloys larly suitable for industrial atmospheres and for
based on AlCu and AlCuMg have been devel- pipe systems in the chemical industry. The
oped with a 10% lower density and a 15% in- seamless tubes extruded over a mandrel are fur-
creased modulus of elasticity. The lithium con- ther processed by drawing.
tent has to be approximately 3%. Special The age-hardening materials with their favor-
melting and casting technology is required be- able mechanical properties are mainly used for
cause of the high reactivity of lithium-contain- superstructures in rolling stock and as hollow
ing melts with oxygen and moisture and the ag- girders for bedplates as well as the manufacture
gressive attack of the lining of the melting of processing plants.
furnaces. The moderately difficult alloys can be pro-
The age hardening of the AlLiCuMg alloys duced as either solid sections or hollow sections
is, in contrast to the conventional aluminum al- whereby the wall thickness has to be set 20 to
loys, characterized by the partly coherent 40% higher than the easily extruded alloys, de-
Al2CuMg particles that occur in addition to the pending on the alloy, for the same circumscrib-
coherent Al3Li precipitates during further hard- ing circle because of the higher deformation
ening. These cannot be cut by dislocations and stress. The AlZn4.5Mg1 alloy is often used for
there is an increase in cross slip, which has a highly stressed welded structures because of its
positive effect on homogeneous slip distribu- good weldability and the rehardening in the
heat-affected zone. In the “age-hardened” con-
dition (2-stage aging), this alloy has a good
resistance to general corrosion and SCC (Ta-
ble 5.7).
Lead-containing alloys such as AlMgSiPb are
available for chip forming machining. They are
particularly suitable for the machining on auto-
matic drilling, milling machines, and lathes be-
cause they enable fast cutting speeds to be used.
The alloy AlMgSiPb has good mechanical
properties, is corrosion resistant, and can be dec-
oratively anodized. The extruded or extruded
and drawn products are primarily supplied as
round, hexagonal, and octagonal bars. The tol-
erances are standardized in DIN1769–1799 and
DIN 5000-59701 (Aluminum Association
H35.2).
Extruded sections in the lithium-containing
aluminum alloys are used as stringer sections
and floor plate supports in the aerospace industry
because of their lower density and increased
modulus of elasticity compared with the con-
ventional high-strength alloys. Further applica-
Fig. 5.34 Recrystallized structural fraction as a function of
tions are limited by the present high billet pro-
the billet heat treatment temperature and the ex-
trusion ratio (extrusion temperature, 550 ⬚C) [Sca 73] duction costs.
236 / Extrusion, Second Edition
5.9.3 Extrusion and Materials Properties trusion process, care should be taken to ensure
that the exit temperature is at least 530 ⬚C. The
The flow stress of AlMg and AlMgMn in-
preheat temperature should, accordingly, be 500
creases with increasing magnesium content, and
to 520 ⬚C because there is no significant tem-
the melting point decreases. To compensate for
perature increase from the heat of deformation.
the lower extrudability of, for example, AlMg3,
On the other hand, with a separate solution heat
the preheat temperature can be set to 30 ⬚C
treatment a lower preheat temperature should be
higher than for AlMg1. However, the exit tem-
selected, and there is no demand on the exit tem-
perature should not significantly exceed 500 ⬚C
perature. The exit speed that can be achieved
to avoid the surface turning brown because of
increased oxidation. As mentioned earlier with with AlMgSi and AlMgSiCu is approximately
naturally hard alloys, the cooling from the ex- only half that of AlMgSi0.5. The extrusion ratio
trusion temperature to room temperature is not on the other hand does not differ significantly
that critical. The process parameters for the in- from that with AlMgSi0.5.
dividual alloys are summarized in Table 5.7. The increase in the mechanical properties of
Higher mechanical properties are obtained the section is achieved by age hardening for 6
with AlMgSi1 and AlMgSiCu by age hardening. to 8 hours at 160 ⬚C or 4 to 6 hours at 180 ⬚C.
However, some compromises have to be made However, it should be pointed out that with
for extrusion. The metallurgical procedures that AlMgSi1, the maximum achievable mechanical
improve the extrudability (e.g., higher billet heat properties decrease with increasing room tem-
treatment temperature) have an unfavorable ef- perature intermediate storage. The damaging in-
fect on the grain formation and thus on the me- fluence of an intermediate room temperature ag-
chanical properties [Sca 67]. ing can be largely overcome by a preventative
In the production of AlMgSi1 sections, the heat treatment. The sections have to be heated
decision has to be taken in the selection of the to 180 ⬚C and held for 3 minutes, which elimi-
metallurgical conditions whether the solution nates the cold aging that would otherwise take
heat treatment and quenching are coupled with place by approximately 1 day [Koe 61].
the extrusion process or whether these should be The alloy AlMgSi1 is suitable for sections
carried out as separate operations. For economic that have to be color anodized because the man-
reasons it is better if additional operations can ganese content that is embedded in the metallic
be avoided. From the metallurgical point of form in the oxide layer produces the brown tone.
view, there are advantages in the formation of Attention must be paid to the grain structure be-
the grain structure if no additional heat treatment cause different microstructures can result in
in the shape of solution heat treatment has to be bands on the surface after anodizing. In this case
carried out. The decisive factor is whether the it has proved advantageous to try and obtain a
age hardening producing Mg2Si is extensively completely fine-grain recrystallized structure.
dissolved at the exit temperature and can be re- This can be achieved when the recrystallization
tained in solution during the cooling. AlMgSi1 retarding influence of the manganese is largely
and AlMgSiCu sections have to be cooled excluded by the formation of coarse secondary
quickly with water because they are quench sen- precipitates and thus the rate of nucleation ac-
sitive due to the manganese content [Sca 64]. celerated and recrystallization promoted [Sca
Whether this requirement can be fulfilled de- 69]. Billet heat treatment at 570 to 590 ⬚C has
pends on one hand on the section shape to be proved successful in this respect. The associated
produced, in particular, the wall thickness, and simultaneous reduction in the mechanical prop-
on the other hand, on the cooling system in- erties is not important for applications in build-
stalled on the extrusion press. As a general rule, ings.
the rate of cooling of AlMgSi and AlMgSiCu in The copper-free age-hardening AlZn4.5Mg1
the temperature range 530 to 150 ⬚C has to be a alloys are very suitable for the production of hol-
factor of 10 faster than with AlMgSi0.5; i.e., it low sections and flat sections because with this
should be at least 10 to 20 K/s. The required material the working temperature in extrusion
cooling rate can only be achieved with water. coincides with the solution temperature range,
Quenching with water after the die can, how- and this alloy has a low quench sensitivity so
ever, result in uncontrolled distortion of the sec- that air cooling suffices.
tion that must be kept to a minimum by pullers. Also, the mechanical properties that can be
If the solution heat treatment and quenching achieved are higher than AlMgSi1. However,
are to be carried out simultaneously with the ex- with incorrect treatment, a tendency to SCC can-
Chapter 5: The Production of Extruded Semifinished Products from Metallic Materials / 237
not be completely excluded. Today it is gener- ular, the AlZnMgCu systems. Alloy technolog-
ally recognized that the danger of SCC of ex- ical procedures have to be followed, however,
truded sections can be excluded if the production that can be disadvantageous from other perspec-
conditions are strictly maintained. These con- tives. The addition of up to a few percent copper
ditions are [Sca 73]: results in the formation of low-melting-point in-
termetallic phases. They also have an unfavor-
● The billet heat treatment must be carried out able effect on the general corrosion resistance.
at a low temperature (12 h at 460–480 ⬚C) Recrystallization retarding elements, including
to suppress the recrystallization by fine man- manganese, chromium, and zirconium, also
ganese, chromium, or zirconium phases. have to be added in order to obtain a hot-worked
● The extrusion temperature should be as low
structure in the extruded sections that contains
as possible (450–490 ⬚C). elongated grains in the longitudinal direction.
● The cooling with air in the temperature range
The mechanical properties in the longitudinal di-
350–200 ⬚C should be in the range 0.5–1.5 rection are higher than in the transverse direc-
K. Water quenching should be avoided at all tion. This is referred to as the extrusion effect
costs. [Sca 69c]. The alloy technological measures de-
● The age hardening—after an intermediate
scribed do fulfill the mechanical property re-
room temperature aging of at least 3 days— quirements but have serious hot-working dis-
has to be carried out in stages (12 h at 90 ⬚C advantages. The additions of the main alloying
plus 12–24 h at 120–130 ⬚C) to produce an elements magnesium and copper and the addi-
overaged structure. tions of manganese and chromium increase the
The extrusion behavior of the alloy flow stress significantly so that AlCuMg2 and
AlZn4.5Mg1 from the point of view of the ex- AlZnMgCu1.5 have to be classified among the
trusion speed is comparable to the alloy Al- difficult-to-extrude alloys. The difficulty is in-
MgSi1. The advantages of AlZn4.5Mg1 are the creased by the low-melting-point phases, which
relatively low solution heat treatment tempera- severely limit the extrusion temperature range,
ture and the use of air even with thick-wall sec- and if the latter is exceeded, hot cracking occurs.
tions to achieve the necessary slow cooling rate. These alloys have a marked quench sensitivity
The extrudability of the alloy AlLiCuMg is and a severely limited solution range so that in
comparable with that of the moderately difficult most cases they have to be solution heat treated
alloys AlMgSi1 and AlZn4.5Mg1. The flow and quenched in a separate operation.
stress of AlCuMgSi is approximately 10 to 15% In addition to these alloys, the AlMg and
lower than that of AlMgSi1. The maximum ex- AlMgMn alloys with 4 to 5% magnesium are
trusion speed that can be obtained is reduced to included in the difficult-to-extrude alloys. The
a value of only 60% of that of AlMgSi1 because flow stress of 47 to 56 N/mm2 is attributable to
of the low-melting-point copper phase. It is ben- the high magnesium content and the manganese
eficial with the lithium-containing alloy as with secondary precipitates, particularly if these oc-
the other high-strength materials to pass the sec- cur in a fine format and a high density in the
tion through nitrogen as it leaves the die to avoid matrix.
oxidation of the surface [Sca 79]. It should be pointed out here that new pro-
The age hardening of the lithium containing duction processes are being used to develop new
alloys is carried out by solution heat treatment aluminum alloys for extruded sections with im-
at 530 to 540 ⬚C and quenching in water. Cold proved materials properties. These include al-
working (stretching) of 1.5 to 2% before aging loys produced by powder metallurgy and parti-
at 185 ⬚C has proved to be beneficial to both the cle reinforced conventional alloys [Web 89] (see
magnitude of the strength and the elongation the section “Extrusion of Powder Metals” in this
[Tem 91]. chapter).
cal properties and a good toughness. It is very The high-alloyed alloys AlMg5 and
important in the aerospace industry. The alloy AlMg4.5Mn are particularly suitable for low
AlCuMgFeNi has the best high-temperature me- temperature applications. The mechanical prop-
chanical properties of all the conventional al- erties increase as the temperature falls; this also
loys. The alloy AlCuSiMn is characterized by applies to the elongation to fracture. If the mag-
high mechanical properties at room temperature nesium content exceeds 3%, some of the mag-
and elevated temperatures. Because this alloy nesium exists preferentially as intermetallic
also has excellent forging properties, preforms phases on the grain boundaries and some in the
are extruded and then forged in dies. Bars for matrix. This applies in particular if the material
drilling, milling, and turning are made from the is held for a long period in the temperature range
alloys AlCuMgPb and AlCuBiPb. 250 to 150 ⬚C. Intercrystalline corrosion suscep-
The billet heat treatment of these alloys is tibility can occur under unfavorable conditions
usually carried out at 480 Ⳳ 5 ⬚C. Only Al- if the application temperature is ⬎80 ⬚C. The
CuMgFeNi is heat treated at 525 Ⳳ 5 ⬚C be- magnesium phase can be precipitated by suitable
cause of the additions of nickel and iron. The thermal treatments during production so that no
heating should not significantly exceed 50 ⬚C/h coherent precipitates form and intercrystalline
to avoid melting. After the heat treatment, slow corrosion can be practically eliminated.
cooling to approximately 360 ⬚C is recom-
mended, preferably in the homogenizing fur- 5.10.2 Extruded Products
nace. The cooling can then be carried out in air.
The high-strength materials are mainly used
These measures help avoid quenching stresses,
in the aerospace industry, military applications,
which can produce cracks in the billets in these
and machinery. The products include solid sec-
alloys.
tions, bars, and seamless extruded tubes.
The following AlZnMgCu alloys are the most
AlCuMg2 and AlZnMgCu1.5 are normally not
common: AlZnMgCu0.5 and AlZnMgCu1.5,
suitable for the production of hollow sections
which are both standardized, as well as alloys
with extrusion welds because of the low-melt-
with higher zinc contents in which manganese
ing-point phases and the high extrusion pres-
and chromium are replaced by zirconium. This
sures required [Wei 78]. Simple, thick-wall tu-
reduces the quench sensitivity of these alloys.
bular components are, however, occasionally
The highest mechanical properties measured on
extruded with bridge or porthole dies.
extruded sections are typically Rp0.2 580–610 N/
Whereas AlCuMg2 is usually used in the
mm2 and Rm 610–640 N/mm2 and approxi-
room temperature age-hardened condition for
mately 8–10% for A5.
high-stress applications, AlCuSiMn and
The billet heat treatment of these alloys is par-
AlCuMgFeNi as well as AlZnMg alloys are
ticularly important because of the complexity of
mainly used after hot age hardening. AlCuSiMn
the cast structure. Structural rearrangements oc-
is used in the as-extruded or annealed state for
cur during heating, holding at temperature, and
subsequent processing to forged components.
cooling, and these have a significant influence
Only the alloy AlMg4.5Mn of the difficult-to-
on both the mechanical properties and the ex-
extrude naturally hard alloys can be extruded as
trudability. Cast billets have a lower melting
a hollow section with extruded welds. However,
point than homogenized billets. The melting
this is possible only with a large wall thickness
point is increased by 70 to 90 ⬚C by reducing
because of the high deformation loads. The ap-
the residual melt bands and segregations as well
plications are primarily chemical equipment and
as dissolution during the billet heat treatment.
machinery.
On the other hand, the supersaturated dissolved
fractions of the peritectic phases are precipitated
in a fine form in the matrix by thermal activa- 5.10.3 Extrusion and Materials Properties
tion. In the billet heat treatment—usually 12 h Only extrusion ratios of V ⳱ 10 to V ⳱ 40
at 480 Ⳳ 5 ⬚C —the cooling of these alloys has are used for the difficult-to-extrude alloys be-
a decisive influence on the extrusion speed [Fin cause of the high flow stress of over 45 to 57 N/
96]. If the cooling is not fast enough, coarse par- mm2. The extrudability is less than 10% of the
ticles can form during the cooling. These do not easily extruded alloys.
dissolve completely during heating and then Indirect extrusion of high-strength alloys has
melt in the extrusion process, resulting in sur- been used to an increasing extent in recent years.
face cracks in the section. This has clearly confirmed the advantages of the
Chapter 5: The Production of Extruded Semifinished Products from Metallic Materials / 239
indirect extrusion process for the high-strength and the AlCuMgFeNi alloys to achieve the de-
and difficult-to-extrude alloys AlCuMgPb, sired high mechanical properties. The age-hard-
AlCuSiMn, and AlZnMgCu1.5 [Eul 75]. Indi- ening parameters are given in Table 5.8.
rect extrusion has a higher productivity com- Finally, the difficult-to-extrude alloy AlMg
pared with direct extrusion. Significant advan- 4.5Mn is a naturally hard alloy where the in-
tages include the higher extrusion speed at lower crease in mechanical properties is not obtained
temperatures (340–360 ⬚C) and the use of longer by heat treatment but by solid solution and work
billets (3–7 times the container diam). The dif- hardening. For this reason, the extrusion ratio
ferent material flow in indirect extrusion pro- should not be too high; otherwise, the fraction
duces a homogeneous structure and thus more of recrystallized structure increases to such an
uniform properties. However, indirect extrusion extent that the specified values are not reached.
places higher demands on the casting quality. This occurs, in particular, when a higher extru-
Only defect-free turned or scalped billets give a sion temperature has to be used because of the
good extruded surface finish. The distance be- limited specific pressure of the extrusion press.
tween the die and the cooling section at the press
exit is greater because of the design of indirect
extrusion presses. This makes the quenching of
quench-sensitive alloys at the press more diffi-
cult. In addition, quenching at the press requires
a sufficiently high exit temperature to achieve Extrusion of Materials with
complete age hardening. In direct extrusion, the
extrusion speed of difficult-to-extrude alloys is
Deformation Temperatures
increased by 20 to 40% by die cooling with ni- of 600 to 1300 ⬚C
trogen. This is demonstrated with the copper-
containing alloys, which have a relatively low
melting point. Die cooling enables some of the 5.11 Extrusion of Semifinished
deformation heat to be removed so that the criti- Products in Copper Alloys
cal melting temperature, which results in section
cracking, is reached at a higher exit speed
Martin Bauser*
[Sca 79].
The solution heat treatment of the high-
strength alloy AlZnMgCu1.5 is usually carried 5.11.1 General
out separately after extrusion. The reason for 5.11.1.1 Copper, Bronze, and Brass—
this has already been discussed. This is then fol- A Long History
lowed by age hardening. Room temperature in- The knowledge and application of copper and
termediate aging for 3 to 5 days has proved ben- some of its alloys extends back into prehistory
eficial. The age hardening is carried out in one (Bronze Age). They were used up to the begin-
or two stages (Table 5.8) and depends on the ning of our technical era mainly for jewelry and
customer specifications. If the maximum me- household goods. The good workability of cop-
chanical properties are required, age hardening per and copper-zinc alloys combined with the
is carried out at only 120 ⬚C to the maximum of attractive appearance is responsible today for
the age-hardening curve. However, a slightly their use for metal wares, including containers,
overaged condition is recommended because lamps, and trays as well as brass instruments.
this significantly improves the stress-corrosion
resistance for only a slight loss in mechanical
properties. A two-stage age hardening is used to 5.11.1.2 Advantageous Physical and
achieve the T73 designated properties. The sec- Chemical Properties
tions are initially aged for 12 to 24 hours at 120 Copper is the commercial metal with the high-
⬚C and then for 3 to 5 hours at 170 ⬚C [Dah 93]. est electrical conductivity (58 m/X mm2 at 20
The alloy AlCuMg2 is usually aged at room ⬚C). The additions to some low-alloy copper ma-
temperature after quenching in water as hot age
hardening has a negative influence on the cor-
rosion properties; a tendency toward intercrys-
talline corrosion can be detected. Hot age hard- *Extrusion of Semifinished Products in Copper Alloys,
ening is the standard process for the AlCuSiMn Martin Bauser
240 / Extrusion, Second Edition
terials only reduce the conductivity slightly but 5.11.1.3 Importance of Extrusion
significantly improve the mechanical properties. in the Processing
The high thermal conductivity corresponds to
Pure copper melts at 1083 ⬚C. The melting
the high electrical conductivity. Copper is lo-
point is only increased by the addition of nickel
cated close to the noble metals in the electrical (continuous solid solution). All other element
chemical series and has a natural resistance to additions lower the melting point, sometimes to
numerous corrosive effects. less than 900 ⬚C (Table 5.9). The recrystalliza-
The good corrosion resistance and the ease of tion temperature falls in the range 350 to 650 ⬚C
working make copper one of the most important depending on the composition. Copper alloys
materials for water supply pipes. It is also par- are extruded at temperatures between 550 and
ticularly suitable for heat exchangers because of 1000 ⬚C corresponding to the melting tempera-
its good thermal conductivity. The property of ture. Along with aluminum alloys, they belong
copper used most is the excellent electrical con- to the group of materials where long semifini-
ductivity, which secures its very wide applica- shed sections are mainly produced by extrusion.
tion in electrical engineering and electronics— According to the statistics in Europe in 1988,
naturally also in the form of rolled products. 1.4 million tonnes (metric tons) of extruded
products were produced in copper alloys by 70 higher temperatures than with aluminum alloys.
companies and approximately 120 presses [Zei However, as copper alloys can usually be ex-
93]. In Germany there are 14 companies with 37 truded at much higher speeds than aluminum,
presses in the range 10 to 50 MN press power. the contact time with the tooling is so short that
Sixty percent of all extruded products are bar, heating of the tools over the limit of 500 to 600
wire, and section of which the majority are pro- ⬚C can be avoided. The tooling wear is, however,
duced in copper-zinc alloys (brass). The remain- naturally much higher than with aluminum al-
ing 40% are tube—usually in copper. loys (see the section “Tools for Copper Alloy
Extrusion,” in Chapter 7).
extrusion tolerances of copper alloys are wider authors have used various methods of measure-
than with aluminum and it is also not possible ment these data are not suitable for comparison.
to produce thin profile cross sections (see DIN Up to the extrusion temperature, copper and
17 674, page 3). With few exceptions the sec- low-alloy copper materials have the face cen-
tions have to be subsequently drawn. Section tered ␣-structure, which does not have good hot-
production is usually limited to copper and low- working properties.
alloy copper materials as well as the easily ex- Brass in the ␣-b range (free-machining brass)
truded ␣-b brasses. has very good hot workability. The extrusion of
The most economic production of readily brass bars was the first large-scale application of
cold-worked alloys to tubes, bar, and section de- this process (A. Dick, 1890, see the section “His-
pends on the equipment available at the individ- toric Development of Extrusion” in Chapter 1).
ual companies. Depending on the type of press, With difficult-to-extrude alloys, the flow
the size, and the number and size of the drawing stress, depending on the press size and the ex-
machines, the most suitable extruded dimen- trusion ratio, places a lower limit on the extru-
sions vary for the same finished product. sion temperature and an upper limit on the sus-
ceptibility to hot shortness [Lau 76]. Aluminum
bronzes and lead-containing nickel silvers are
particularly susceptible to hot shortness. The
5.13 Extrusion Properties of cracks can range from light surface cracks to fir
Copper Alloys tree defects (Fig. 5.35). It is not only on eco-
and wide circular recess into which the thin shell 5.13.6.3 Back End Defect
folds. Extrusion with a shell is still carried out
with the combination dummy block and clean- If the extrusion ratio is too low (heavy sec-
ing pad but the additional cleaning operation is tions), there is the risk of the “back end defect”
eliminated. forming particularly with material that flows ac-
cording to type C in direct extrusion. The ac-
celerating material in the center of the billet can
5.13.6 Different Material Flow Behavior form a funnel at the end of extrusion. Short billet
lengths and large discard lengths can be used to
In the direct extrusion of copper alloys with reduce this (see Fig. 5.47).
a shell and unlubricated container, flat dies are Back end defect is seen less in indirect extru-
used. Differences in the hot-working properties sion than in direct extrusion and only when the
and the flow behaviors of different material extrusion ratio is too small and the discard too
groups result in different types of material flow. thin.
The material flow patterns can be found in Chap-
ter 3.
5.13.7 Discard Length
Blisters on the surface of the extrusion can be strands can be pulled with a single puller, with
avoided on susceptible alloys by extruding with copper alloys a specific puller device must be
a lubricated container. It is necessary to use a provided for each strand. The exit speeds of the
conical entry in the die and to machine the billet individual sections are not exactly equal so that
surface. The billet surface forms the surface of the slower section would be severely stretched
the section because of the laminar flow and at the high exit temperature.
every defect on the billet surface appears on the Indirect extrusion is often used for brass wire
section. and rod because this avoids the piping defect and
long billets can be used.
5.13.9 Extrusion into Water or Air A rod and section press—usually the direct
process—has a section cross-transfer system as
Alloys that tend to oxidation are often ex- well as the puller system and frequently a water
truded into a water bath or through a water wave. trough in which the sections can be quickly
This ensures that the extruded product does not brought to room temperature after crossing the
have to be pickled before subsequent further critical temperature of approximately 300 ⬚C.
processing. It is also possible with copper tube Wire is also cooled in water after a specific cool-
to restrict the secondary recrystallization ob- ing time in air.
served when extruding into air and thus a coarse If a wide range of materials and dimensions
grain on the exit from the die [Gre 71]. A fine have to be processed, a multipurpose press is
grain is often required for further processing. still the correct choice.
Water cooling should, as a general rule, be
avoided for ␣-b materials because otherwise, as 5.14.2 Tube Extrusion
the material leaves the die, the structure con-
sisting mainly of the b-phase is undercooled and Tube presses today obviously have a piercer
it is possible for some of the ␣-phase to precip- system. Water-cooled mandrels are used that
itate as needles. Both reduce the workability and usually move with the stem (moving mandrel).
increase the strength of the extrusions [Bro 73]. The mandrel that is stationary in the die during
If more rapid cooling than air cooling is required extrusion is subjected continuously to a high
(e.g., with brass wire), the material can only temperature. The “stationary mandrel” is there-
come into contact with water after air cooling fore used only for the extrusion of tubes with
(to 500–300 ⬚C, depending on the material) if it small internal diameters and suitable hollow sec-
is to remain soft. Direct slower cooling with a tions.
water-air mixture is possible. Copper sections are extruded under water (or
occasionally in a protective atmosphere).
In the 1950s and 1960s a large range of ver-
tical tube presses were installed. They were built
5.14 Extrusion Processes and because the vertical axis simplified the align-
Suitable Equipment ment of the mandrel to the container and the die
giving a better tube concentricity. On today’s
Whereas earlier extrusion plants were mainly horizontal presses the tools can be so easily ad-
multipurpose plants capable of producing rod justed and guided that this advantage no longer
and sections as well as wire and tube, today ex- applies. Horizontal presses need simpler foun-
trusion plants are designed specifically for the dations and enable larger section weights to be
production of large quantities of one product produced and have therefore almost completely
[Ste 91]. Specific design details are given in displaced the vertical tube presses.
Chapter 6.
5.14.3 Drive
5.14.1 Extrusion Presses for
Whereas water and accumulator driven extru-
Brass Wire and Sections
sion presses were previously exclusively used
There are some presses on which large quan- for copper alloys giving high ram speeds (up to
tities of brass are produced where only wire is 150 m/s), these are used today only for copper
extruded onto down coilers and others that are tube and thick sections.
equipped with pullers (up to 4 sections) for the In other cases direct oil drives are used, al-
production of rod and sections. In contrast to the though these allow only a maximum ram speed
extrusion of aluminum sections where several of approximately 50 mm/s at an economically
246 / Extrusion, Second Edition
acceptable investment; this is usually adequate. with rod, sections, and tubes. With coiled wire
The advantages of oil drive (good speed control this is obviously not necessary. In this case the
and regulation over the billet length, simpler maximum billet length is selected. Alloys that
maintenance, and smaller footprint) predomi- are susceptible to piping are usually limited to
nate. Exact speed control is particularly advan- 2.5 to 3.5 times the diameter in direct extrusion.
tageous for a linked puller and synchronously For extruded tubes the traditional rule of
operating wire coilers. Variable oil drive also thumb is that the billet should not be longer than
simplifies the automation of the extrusion pro- 5 times the mandrel diameter because of the in-
cess. creasing risk of wall thickness eccentricity as the
billet length increases. The billet length also has
5.14.4 Die Changing to be restricted because of the occurrence of
shell defects (e.g., with low-extrusion-ratio cop-
It must be possible to easily change dies and per tubes).
to control them on copper alloy presses: the high
thermomechanical stresses result in such severe
wear and deformation of the shape forming dies 5.15.3 Billet Processing
that dressing can be required after only a few In the case of lubricated extrusion or if the
extrusions. Chapter 6 describes suitable die billet surface is defective (particularly with flow
changing systems (rotating arm, slide). type B), the billet has to be skimmed. This ex-
Quick container changing is more important pensive operation is, naturally, avoided as much
than in aluminum extrusion because of the wear as possible by preferably extruding with an un-
of the liner. lubricated container and a thicker shell that col-
lects the casting defects.
5.14.5 Discard Separation In indirect extrusion without a shell and a con-
The discard is normally removed with the ical die, the billet surface forms the section sur-
saw, in contrast to aluminum extrusion where it face similar to direct extrusion with a lubricated
is usually sheared. It is important that good container. All billets then have to be skimmed.
swarf extraction prevents damage of the product To avoid this, extrusion with a shell and a flat
from swarf. die is also carried out with indirect extrusion so
In indirect extrusion and direct extrusion of that a dead metal zone forms. Both hinder the
small solid sections a powerful shear is, how- flow of the billet surface into the surface of the
ever, preferred [KM 77]. section. The risk of defects is, however, signifi-
cantly greater than in direct extrusion and par-
ticular emphasis has to be placed on a good,
smooth billet surface.
5.15 Billet Production and Heating If large-format tubes are extruded from large-
diameter billets, the piercing load of the press
5.15.1 Continuous Casting and may not be large enough and the billet has to be
Homogenizing prebored. The general rule is that the bore di-
Chill cast molds were still used up to the ameter should be approximately 5 mm larger
1960s. They were completely replaced by the than the mandrel diameter so that the lubricant
continuous casting method developed circa 1930 is not wiped off as the mandrel enters the billet.
(see the section “Systems for the Production of
Copper Billets” in Chapter 6). Horizontal or ver- 5.15.4 Billet Quality Control
tical casting is used depending on the billet cross
section and alloy and usually on continuous The billet quality must in any case be care-
plants. Homogenization of the billets is not nor- fully checked before extrusion. This includes
mally required apart from tin bronze, which is porosity and crack monitoring of sensitive ma-
susceptible to severe segregation, where the risk terial as well as visual inspection of the billet
of cracking is reduced. surface.
The most economic heating in a gas furnace nelectrical purposes. The STP and ETP desig-
is adequate to heat materials with a relatively nations are used for electric bus. The most
low extrusion temperature (e.g., free-machining expensive variation is OF-Cu that is oxygen free
brasses), even though in terms of the final tem- without a deoxidation agent.
perature it is less accurate and less reliable. A Oxygen-containing copper is sensitive to
temperature profile can be applied, if needed, by heating in a hydrogen-containing atmosphere.
subsequent heating in an inline induction fur- The oxygen forms water vapor in the pores of
nace with several heating zones and, in any case, the annealed material with the diffused hydro-
the billet temperature can be more accurately gen, and this can burst open the structure. If the
controlled. There are also cases in which gas fur- material has to be suitable for welding, brazing,
naces are used even with higher billet heating or annealing, the oxygen has to be bonded,
temperatures (e.g., copper). In these cases in- which is carried out by phosphorus in SF-Cu
duction furnaces are more common because the (0.015–0.04%). Water supply tubes are the main
risk of overheating is reduced. High billet pre- application of this copper grade.
heating temperatures are simultaneously close to
the solidus temperature and thus there is a risk 5.16.1.2 Hot Workability,
of the billet melting. Extrusion Temperature
To reduce costs with high billet heating tem-
peratures, the first heating step can be carried out The hot workability of copper is limited by
in a gas furnace and the second in an induction the fcc structure up to the melting point (see the
oven. hot-strength curve in Fig. 5.36). The extrusion
In every case an inline electrically heated temperature is accordingly very high (800–950
equalization chamber can be used in which tem- ⬚C), and a high extrusion ratio is possible only
perature variations between the billet front and on powerful extrusion presses.
back can be removed and in which billets can
be maintained at temperature during press 5.16.2 Copper Tube
downtime.
5.16.2.1 Application
SF-Cu is used exclusively for domestic water
5.16 Copper Extrusion pipe, the most common use of copper tubes, be-
cause these need to be welded or soldered. How-
5.16.1 General ever, SF-Cu is also used for underfloor heating
Unalloyed copper is mainly extruded to tubes or for industrial applications (heat-exchanger
and, to a small degree, to bar and sections. Cop- tubes in air-conditioning units, for chillers, etc).
per wire is, in contrast, usually cast, hot rolled,
and drawn.
Whereas water supply pipes are available as sively in the production of gas and water supply
hard or half-hard pipes or annealed coiled tubes pipes.
(DIN 1786/EN 1057), industrial tube is usually In the production of industrial tubes with wall
supplied in annealed multilayered coils (coil thickness down to 0.35 mm and finned tubes,
weight 60–120 kg). Internal and external finned the demands on the starting tube are very high
tubes for heat exchangers are also produced in so that only the second and third processes with
SF-Cu because of the good thermal conductivity extrusion are used.
of copper and its excellent cold workability.
5.16.2.3 Extrusion
5.16.2.2 Production Methods
The press and the tooling have to be accu-
Numerous modern copper tube plants have rately aligned so that a low tube eccentricity
been installed specifically for the production of (Ⳳ7% and under) can be achieved. In spite of
SF-Cu tubes. The combination of the very good careful alignment of the centerline of the con-
cold workability with the reduced hot workabil- tainer, stem, and mandrel as well as the die,
ity enables hot working to be used to produce a movement of the mandrel during extrusion is al-
tube larger than the finished dimensions fol- most impossible to avoid. Therefore, to achieve
lowed by cold working to the finished size by a low eccentricity it is usual to limit the length
cold pilgering and drawing machines without in- of the unmachined billet to 5 (up to 8) times the
termediate annealing. Soft tubes are given a final mandrel diameter.
anneal. Half-hard tubes are lightly drawn after The tube is usually extruded at high speed un-
annealing. der water within a few seconds, which reduces
Three processes compete for the production the risk of mechanical damage and produces the
of copper tubes [Tus 70]: fine grain needed for extensive cold working.
● Production using a piercer, cold pilger ma- Only direct extrusion presses are used.
chine (tube rolling), and drawing machines: To avoid water getting inside the tube, con-
Heated billets are rolled with inclined rolls trolled mandrel movement is used at the start
over a mandrel to tube blanks. A straight and the end of extrusion to give a tube closed at
tube up to 150 m long is then produced on a both ends (Fig. 5.37). The extruded tube is then
multistage cold pilger machine with a reduc- oxide free internally and externally and can be
tion ratio of 10:1 followed by redrawing. passed to the cold pilger machine or drawing
● Production on an extrusion press, cold pilger
machine without pickling.
machine, and drawing machines: The usual
dimensions of the extruded tube are 80 ⳯ 5.16.2.4 Oxide on the Billet Surface,
10 mm with a piece weight of more than 400 Shell and Blister Defect
kg. As in the first process, the extruded tube
is then further processed with cold pilger ma- As mentioned previously, there is the risk
chines and drawing machines. Schumag ma- with copper flowing according to type B that the
chines and spinner blocks are used. oxide produced on billet heating acts as a lubri-
● Production on an extrusion press and draw- cant between the billet surface and the container
ing machines: A so-called thin tube, e.g., 73 and flows along the dead metal zone that forms
⳯ 4 mm and a length of approximately 50 in front of the flat die: extrusion shell defects are
m but a lower piece weight, is extruded. the consequence (Fig. 5.38). They produce blis-
Without the need for a cold pilger operation ters when drawn tubes are annealed (Fig. 5.39).
these tubes go directly to the drawing ma- Fast induction heating is recommended (at
chines. least as the final stage) to ensure that the mini-
mum of oxide forms on the billet surface. The
In the first process (with no extrusion press) oxide on SF-Cu copper does not adhere strongly
there is the risk of cracks and thus laps and oxide to the surface—in contrast to the oxide on oxy-
inclusions, which impair the quality of the tubes gen-rich qualities. It can be largely removed by
if the high demands of the casting process are a strong water spray at the furnace exit. At the
not fulfilled. In the production of gas and water same time the billet hardly loses any heat. Hot
supply pipe with a minimum wall thickness of scalping of the oxidized billet surface, which is
1 mm this does, however, play a minor role. This mentioned in the literature, is now rarely used
very economic process is used almost exclu- [Vat 70].
Chapter 5: The Production of Extruded Semifinished Products from Metallic Materials / 249
In conventional extrusion with a shell, the aim risk of lines of blisters is reduced by the selec-
is for the oxide layer to be retained on the con- tion of a large extrusion ratio, which increases
tainer liner. This does not occur completely. Be- the distance between the billet surface and the
cause, as shown in Fig. 5.38, the oxide first ar- surface of the extrusion. If the billet is short
rives at the die toward the end of extrusion, the enough, the flow of the oxide is stopped in time
in front of the die.
As already mentioned, the extruded shell is so
thin and ductile that a combination dummy
block and cleaning block can be used in extru-
sion.
Fig. 5.38 Extrusion shell formation in the extrusion of copper tubes [Bau 93]
250 / Extrusion, Second Edition
are, if possible, extruded from large billets oxide flowing into the weld seam. This can be
pierced in the press and, for small openings, over avoided only by good technical knowledge and
the mandrel tip (fixed mandrel). With difficult experience. The extrusion of copper through
shapes, prebored billets can be necessary. The bridge dies is therefore rarely used.
shape of the mandrel tip and the exact location
in the die require considerable experience. 5.16.4 Extrusion of Low-Alloy
Hollow sections have to be extruded through Copper Materials
bridge dies if the openings are asymmetrical or
5.16.4.1 The Materials, Properties,
if the section has several openings. This process
is similar to that for aluminum alloys. However, and Applications
with copper, deformation and cracking of the Low-alloy copper materials are covered by
very expensive dies can occur along with the the standard DIN 17666 (UNS C-10100–
Fig. 5.39 Blisters on the tube surface of a SF-Cu-tube after annealing. (a) Transverse section. (b) External surface with line of blisters
[Die 76]
Fig. 5.40 Example of extruded and drawn copper sections. (a) Solid section. (b) Hollow section (Source: Kabelmetal Osnabruck)
Chapter 5: The Production of Extruded Semifinished Products from Metallic Materials / 251
C15815). The composition, properties, and ap- are extremely high as is, as described previously,
plications of the different alloys are described in the risk of flaking and blistering [Hes 82]. As a
detail in the DKI information sheet 8 [DKIa]. general rule, only relatively short billets can be
In the non-age-hardening alloys, additions of extruded (length:diameter ⳱ 1 to 1.5:1). The
silver, cadmium, magnesium, and iron increase billet heating time in the induction oven can
the mechanical properties and, in particular, the sometimes be too short to completely dissolve
softening temperature without reducing the con- the second phase and to achieve the maximum
ductivity significantly. Tellurium and lead im- mechanical properties.
prove the machinability. Additions of beryllium, The section has to be cooled in water to freeze
nickel, silicon, chromium, and zirconium pro- the solid-solution state. Above a specific section
duce age-hardening alloys that have high me- thickness (60–70 mm diam) water quenching at
chanical properties and simultaneously high the press is no longer sufficient. In this case the
electrical conductivity after solution heat treat- section has to be solution heat treated after ex-
ment and age hardening. trusion in a special oven and then quenched. In
Application examples of the low-alloy copper this case a lower extrusion temperature can be
materials are found mainly in electrical technol- used because the extrusion process and the so-
ogy and chemical plant construction, e.g., con- lution heat treatment are not combined.
tacts and spring elements as well as (CuCr, The hot age hardening following solution heat
CuCrZr) welding electrodes (see also the section treatment (e.g., 475 ⬚C for CuCr) is carried out
on copper alloy extruded products in Chapter 2). before or after the cold working, depending on
Alloy development in recent years has re- the properties required.
sulted in some nonstandard age-hardening ma-
terials for elements of electrotechnology and
5.16.5 Extrusion of Copper-Zinc
electronics. The majority are used only in the
form of strip, and extruded and drawn products Alloys (Brass and Tombac)
are rarely used.
5.16.5.1 Binary Copper-Zinc Alloys
5.16.4.2 Extrusion
Properties, Structure. Brass alloys are the
The low-alloy copper alloys have similar ex- most commonly used of the copper alloys and
trusion properties to unalloyed copper. The risk long sections are almost completely produced by
of flaking and blister formation by the inflow of extrusion. All copper-zinc alloys with a copper
oxide into the funnel behind the dead metal zone fraction more than 50% are referred to as
is usually even higher than with copper because brasses. More than 72% copper, the copper-zinc
of the greater tendency to oxidation [Moi 89]. alloys are also referred to as “tombac.” These
The oxide thickness also increases when a are alloys with a reddish color. As the copper
higher extrusion temperature has to be used for content is reduced corresponding to an increase
the same extrusion ratio because of the higher in the zinc content, the color changes more and
hot strength. It is advisable in such cases to blow more to yellow, and at the same time the hard-
off the oxide from the hot billet using a water ness increases.
spray. The copper-zinc phase diagram is described
Figure 5.36 shows some hot-strength curves. first because of the marked variations in me-
Extrusion data are given in Table 5.9. chanical properties and structure with the zinc
content.
5.16.4.3 Solution Treatment at the Press As shown in Fig. 5.41, three alloy groups can
The mechanical and electrical properties of be clearly differentiated:
the age-hardening alloys are obtained by solu- ● Single-phase ␣-alloys with a copper content
tion heat treatment followed by hot age hard- above 61%
ening. If the cross section is not too high, the ● Binary-phase ␣/b-alloys with a copper con-
solution heat treatment of CuCr and CuCrZr can tent of 54 to 61%
be carried out on the press. This process is well ● Single-phase b-alloys with a copper content
known from the low-alloy aluminum materials. of 50 to 54%
Because, however, in this case the solution heat
treatment has to be carried out at approximately The single-phase ␣-alloys have a fcc lattice
1000 ⬚C, the stresses in the container and the die similar to pure copper. They can correspond-
252 / Extrusion, Second Edition
ingly be easily cold worked (see structure in Chip forming additions—usually between 1 and
Fig. 5.42). 3% lead—that are embedded as droplets in the
The single-phase b-structure is body centered matrix further improve the machinability.
cubic (bcc) and has very limited workability at Materials with only a low b-content (Cu
room temperature. Between these limits (shown Zn36Pb1.5) can be readily machined and cold
by the lines BE and CF on the phase diagram) worked. They are used where stamping or bend-
there is a region in which the ␣-phase and the ing is required. The free-machining brasses
b-phase can coexist. The greater the zinc con- (mainly CuZn39Pb3) are used in large quantities
tent, the lower is the ␣-content. The cold work- as hard drawn rods for processing on automatic
ability reduces in this region corresponding to lathes to turned components of all kinds (e.g.,
the increasing zinc content (see Fig. 5.43, ␣-b- bolts). They can be cold worked only to a limited
structure). extent (see Table 5.11, EN 12164). Pure b-brass
The Materials, Properties, and Applica-
tions. DIN 17660 covers the commercially used
copper zinc alloys (See also ASTM B455 for
Copper-Zinc-Lead [leaded brass] extruded
shapes). The DKI information sheets i.5 and i.15
[DKIb, DKIc] cover these CuZn alloys in detail
(See also Copper Development Association web
site www.copper.org).
The brasses with a pure ␣-structure as well as
the tombac (low-alloy CuZn) alloys are used
predominantly in the form of sheets and strip,
less as tubes, and rarely in the form of bar and
section. The producers of jewelery and metal
ware, brass instruments, lamp bodies, and light-
bulbs use ␣-brasses. Tubes are used for air brake
pipes in goods vehicles and for manometers.
The alloys in the ␣-b field with a b-fraction
between 20 and 40% can be readily machined Fig. 5.42 Structure of ␣-brass, etched. Image width is
and are therefore widely used as rod material. 0.5mm [Wie 86]
Chapter 5: The Production of Extruded Semifinished Products from Metallic Materials / 253
(e.g., CuZ44Pb2) is almost brittle at room tem- significantly lower flow stress than the ␣-struc-
perature but is used for extruded sections that do ture. The ␣-b brasses and especially pure b-
not have to be subsequently cold worked be- brasses therefore have a high extrudability. Fig-
cause of its excellent hot workability. Sections ure 5.45 illustrates this by hot flow stress curves.
in ␣-b brass can, on the other hand, be cold The workability of the CuZn alloys decreases
drawn to a limited extent and therefore be sup- initially in the normal extrusion temperature
plied to tight finished tolerances. Figure 5.44 range of 600 to 800 ⬚C with increasing zinc con-
shows some examples of extruded and drawn tent and then increases again from approxi-
brass sections. They are covered by the DIN mately 30% zinc when b-phases occur during
17674 standard (EN 12167). extrusion.
Extrusion. At the normal extrusion tempera- The low flow stress of the b-phase at the ex-
ture of more than 600 ⬚C, the b-structure has a trusion temperature enables high extrusion
speeds and extrusion ratios to be attained. With
free-machining brass extrusion ratios up to V ⳱
900 and exit speeds up to 8 m/s can be reached.
Table 5.9 gives extrusion data on copper-zinc
alloys.
Because the phase boundaries ␣/␣-b and ␣-b/
b are displaced to higher zinc contents on cool-
ing, the ␣-phase fraction extends into the ␣-b
field on cooling (see Fig. 5.41). The ␣-precipi-
tation can be partially suppressed by quenching
(frozen) so that the b-fraction remains higher
than would be the case in the equilibrium state.
If quenching is carried out after cooling to 500
to 300 ⬚C, depending on the composition, the ␣-
precipitation has stabilized and the structure no
longer changes.
By quenching from the deformation heat and
aging at temperatures approximately 200 ⬚C, ␣-
b-brasses can be given a substantial hardness in-
Fig. 5.43 Brass with acicular ␣-b-structure, etched. Image
width is approximately 0.275mm [Wie 86]
crease by the fine precipitation of the second
phase [Bro 73]. This is rarely used in practice
because it is difficult to maintain the extrusion
Fig. 5.44 Extruded and drawn brass sections (Source: Wie- Fig. 5.45 Some hot tensile strength curves for copper-zinc
land-Werke, Ulm catalog) alloys and SF-Cu [Wie 86]
254 / Extrusion, Second Edition
conditions constant from billet to billet, and at Indirect extrusion is recommended for ␣-b-
the same time the cold workability is restricted. brasses where there is the risk of the extrusion
Possible Extrusion Defects and their Pre- piping defect forming in direct extrusion be-
vention. The high deformation resistance of cause the different material flow excludes this
low-alloy ␣-brasses requires a high extrusion defect. Significantly longer billet lengths can
temperature for a given extrusion press power. then be used [Sie 78].
This increases the danger of coarse grain for- As mentioned elsewhere, in direct extrusion,
mation and in the extreme case, hot shortness. if the extrusion ratio is too low, particularly with
Low initial billet temperatures as well as low brass, the acceleration of the center of the billet
extrusion speed reduce the risk of coarse grain can be so severe that cavities can occur toward
formation and hot shortness, as with all materi- the end of the section (Fig. 5.47). Their forma-
als. However, at the lower extrusion temperature tion in the section can be prevented only by lim-
the deformation resistance is higher and the pos- iting the billet length and leaving a sufficiently
sible minimum extruded cross section for a long discard.
given press power larger. A further defect, particularly with ␣-brasses
With copper-zinc alloys containing more than with a low zinc content, is the formation of zinc
80% copper, copper oxide forms on the billet flakes on the surface of the extruded product.
surface during heating in air. With alloys with Zinc vaporisation from the newly formed surface
less than 80% copper, zinc oxide mainly forms immediately behind the die condenses onto
and this has no lubrication properties in contrast cooler parts of the tooling in the form of fine
to copper oxide. Whereas the CuZn alloys with drops, which can be picked up by the passing
more than 80% copper can still have shell and section. The droplets form zones of high zinc
blister defects, this risk does not occur with content, containing b phase, on the section sur-
higher-zinc-containing materials because the ad- face. These are brittle and can result in defects.
hesion between the billet and the container is so These zinc flakes can also be found on the inter-
large that a closed shell is formed when extrud-
ing with a shell. On the other hand, the combi-
nation dummy block and cleaning disc that can
be used in copper extrusion is not suitable be-
cause of the large shell thickness. A separate
cleaning cycle has to take place after extrusion.
As the zinc content increases, the thermal
conductivity of brass decreases and the periph-
eral cooling of the billet in the container is no
longer equalized. Because the b-rich hotter billet
core flows more easily than the b-impoverished
peripheral zone, the typical flow pattern type C
forms (see Fig. 3.11 in Chapter 3) with the risk
of the piping defect. Figure 5.46 shows an ex-
ample.
The billets should have a perfect surface qual-
ity to avoid extrusion defects. The difference be-
tween the container diameter and the billet di-
ameter should also not be too large to avoid folds
forming as the billet is upset in the container.
With a good quality liner surface, the shell from
the previous extrusion can be completely re-
moved with the cleaning disc [Lot 71].
In direct extrusion, the length of the billet is
limited to reduce the risk of the piping defect.
As a general rule the billet should not be longer
than 2.5 to 3 times the diameter. Routine fracture
testing of the end of the sections can remove any
sections containing the extrusion defect and en-
sure that the remaining length is defect free. Fig. 5.46 Extrusion defect (piping) in ␣-b-brass [Die 76]
Chapter 5: The Production of Extruded Semifinished Products from Metallic Materials / 255
nal surface of tubes. In order to prevent them terial emerging from the die is very soft and it
forming it is necessary to ensure that the hot sec- is necessary to use a defined low puller force to
tion does not contact the tooling behind the die. avoid undesired stretching of the sections.
Handling the Section. Because the ␣-b- If the cross-transfer conveyor is not large
brasses and the b-brasses are very soft at the exit enough, water cooling has to be used at the end
temperature and sensitive to mechanical contact, before the sections can be cut to length. Figure
good guiding out of the die (possibly lined with 5.48 shows the principle of the extrusion of
graphite) is needed to avoid damage of the sec- brass sections.
tion surface combined with careful handling on Cu-Zn wires, usually in free-machining brass,
the runout table. are extruded from one or two cavity dies into
Whereas thick bars from single-cavity dies are down coilers, the speed of which are synchro-
extruded into air on graphite or steel-lined nized with the ram speed. Periodic oscillations
plates, or onto a freely rotating roller conveyor of the rotation speed (wobble) ensure that the
and then cross transferred until they can be individual layers on the drum are not directly
cooled—possibly in a water trough—and cut to above each other. To avoid damage, the strands
length, pullers are usually used for sections and are usually extruded into pans, which at the end
thinner bar. Up to four sections can be simulta- of extrusion are removed from the coilers and
neously pulled using independent jaws. The ma- transported on a roller conveyor until the brass
Fig. 5.48 Schematic of a section and wire brass extrusion plant (SMS Hasenclever catalog)
256 / Extrusion, Second Edition
wire has cooled sufficiently and can be lifted out. Again, as with brass there are single-phase
Further processing is carried out after pickling materials with a fcc ␣-structure and two-phase
by a combination of drawing, straightening, and materials with an ␣-b structure. In both groups
cutting to length. additional intermetallic phases can occur de-
Straightness—b phase distribution—Fur- pending on the type and amount of the additions.
ther Processing of Bar. The straightness of the The b-phase fraction in the ␣-b-mixed struc-
bar is very important for machining on auto- ture, which has a strong influence on the extrud-
matic lathes with high cutting speeds. Bars that ability and the cold workability, can be con-
are not clean or straight chatter in the bar feed. trolled by these additions of alloying elements
If the b-phase fraction and its distribution in the (see Table 5.12, Fig. 5.49).
cross section vary over the length of the extru- Semifinished Products and Applications.
sion, the rectification effect in the combination The alloys CuZn20Al2 and CuZn28Sn1 are re-
drawing, straightening, and cutting to length ma- sistant to seawater and corrosion. They are used
chine changes from the first bar to the last of an in heat exchangers and condensers. Because
extruded coil. they have a pure ␣-structure and consequently
The indirect extrusion process again offers ad- are difficult to extrude but have good cold work-
vantages over the direct process. The variation ability, the tubes are extruded with large cross
in the size and distribution of the b-phase in the sections and brought to the finished dimensions
␣-b mixed structure between the start of extru- on cold pilger machines and draw benches with
sion to the end in indirect extrusion is less than intermediate annealing.
in direct because of the uniform material flow CuZn31Si1 is a material with an ␣-b-mixed
over the length of the extrusion. structure. Tubes for bearing bushes are produced
In multicavity extrusion the billet no longer
flows symmetrically in one strand because the
die apertures are arranged asymmetrically. One Table 5.12 Influence of element additions on
side of the section surface stems from the outer the b-phase fraction and the extrudability of
region of the billet and the other side from the special brasses
inner region. It is therefore particularly impor- Alloying Zinc
tant to ensure a uniform cast structure and good element b-portion equivalent(a) Extrudability
through heating; there are then no disadvantages Silicon Is improved 10 Is improved
for the quality of the section and, in particular, Aluminum Is improved 6 Is improved
Tin Is improved 2 Is improved
for the straightness of the finished bars. Manganese Is improved 0.5 Is improved
In order to obtain uniform mechanical prop- Nickel Is improved ⳮ0.9–ⳮ1.5 Is improved
erties and good straightness, care must be taken (a) 1% the alloying element corresponds to one in the effect on the structure
to ensure that the degree of deformation in the condition one as “zinc equivalent” of indicated multiples of the effect of zinc.
Source: Lau 76
individual drawing operations is held within nar-
row limits requiring that the dimensional toler-
ances of the extruded bar are within tight limits.
Suitable selection of the hot-working materials
for the die and its design are discussed in detail
in the section on tooling for the extrusion of cop-
per alloys in Chapter 7.
in this alloy. Other nonstandardized special DIN 17662 describes the composition of the
brasses (with additions of Mn, Ni, Si, and Pb) common alloys suitable for extrusion with a
have proved themselves as wear-resistant bear- maximum tin content of 8%. The DKI infor-
ing materials in special cases. mation sheet i.15 [DKId] describes the copper-
High-zinc-containing special brasses are con- tin alloys in detail (See also Copper Develop-
struction materials with moderate and high me- ment Center. These tin bronzes are also called
chanical properties used in the manufacture of phosphor bronzes).
chemical plants. Tin-bronzes belong to the oldest known cop-
Casting and Extrusion. Casting defects, in- per alloys. They are still today very important in
cluding porosity and cracks, have to be assumed the chemical industry and ship construction be-
in special brasses, particularly with aluminum cause of their good electrical and thermal con-
and manganese additions. Careful testing of the ductivity with simultaneous high-strength and
billet quality (e.g., using a penetrant such as the favorable corrosion properties. In electrical tech-
Met-L check testing on the cut surface) is nec- nology, significantly more tin-bronze strip is
essary. Billets with defects on the mantle surface used than wire and sections.
have to be machined. CuSn4 and CuSn6 tubes are used for manom-
In the same way as with pure brasses, the ex- eters or suction pipes. Highly stressed compo-
trudability depends on the amount of the b- nents, including gear wheels, bolts, and bear-
phase present at the extrusion temperature. This ings, are made from CuSn8.
is shown by the hot tensile test curves in Fig. The phase diagram in Fig. 5.51 shows that the
5.50. The possible defects and their avoidance wrought materials in the equilibrium state have
follow those described in section 5.16.5.1. a pure fcc ␣-structure and therefore behave like
copper in hot and cold working.
5.16.6 Extrusion of Copper-Tin
Alloys (Tin Bronzes)
5.16.6.2 Casting of Copper-Tin Alloys cause of the low speed and the large difference
between the initial billet temperature and the
Because the cast structure—particularly at the
container temperature. Only short billets can
higher tin contents—tends toward segregation
therefore be used.
because of the wide solidification interval and
With the good cold workability of the fcc lat-
the billets can exhibit tin sweating as a result of
tice the section can be extruded above the final
inverse billet segregation, turning of the billets
dimensions and then worked to the final size in
is advised. Homogenization of the billets (630
several stages—including where necessary in-
to 700 ⬚C for several hours) reduces the risk of
termediate annealing—by section rolling and
extrusion defects in the form of longitudinal and
drawing. This also produces the frequently re-
transverse cracks in the higher-alloyed materi-
quired high mechanical properties.
als. With more than 6% tin, the brittle ␣-b eu-
tectoid that forms on solidification is partly re-
tained in the cooled billet; it can be dissolved 5.16.6.4 Flow Type and Shell Defects
only by this homogenization. Some phospho- Because tin-bronzes tend to oxidize and this
rous is added to the 8% tin-bronze to suppress oxide exhibits good lubrication properties, flow
the tin-oxide formation in melts that have not type A occurs in the direct extrusion of these
been completely deoxidized. These tin-bronzes alloys, giving the risk of shell and blister
are referred to as phosphor-bronzes. defects—particularly with low extrusion ratios,
i.e., thick bars [Vat 70]. With large extrusion ra-
5.16.6.3 Extrusion of Copper-Tin Alloys tios—thin bars—this risk is reduced. Extrusion
is normally carried out without container lubri-
The flow stress of the tin-bronzes is higher
cation and with a thin shell. Care has to be taken
than that of copper as shown in the hot tensile
in the cleaning cycle to ensure that no residues
strength curves in Fig. 5.52 and increases with
of the shell from the previous extrusion remain.
increasing tin content. Tin-bronzes are best
worked between 700 and 750 ⬚C. The extrusion
data can be found in Table 5.9. 5.16.6.5 Competition from Wire Casting
Tin-bronzes containing up to 6% tin are mod- As mentioned previously, only short billets
erately difficult and those with 8% difficult to can be used in wire extrusion giving low coil
extrude. High-alloyed tin-bronzes are very sus- weight. The extrusion process and subsequent
ceptible to cracking and can be extruded only downstream processing is correspondingly ex-
with slow speeds [Moe 80]. pensive. Direct continuous casting of wire in
Bars smaller than 25 mm diameter are ex- large coils has grown in competition to the ex-
truded as several strands and coiled. There is the trusion of thin bar from which tin-bronze wire
risk of the billet “freezing” in the container be- is produced by rolling and drawing.
The production of tin-bronze wire today is
mainly by this continuous casting process
[Bau 76].
from the phase diagram in Fig. 5.53. In contrast, from larger extruded cross sections by cold
complex aluminum-bronzes with aluminum working, then only the 5% aluminum bronzes
contents of approximately 10% and additions of can be considered.
iron, nickel, manganese, and silicon individually Extrusion and Extrusion Defects of Cop-
or together usually have a heterogeneous struc- per-Aluminum Alloys. The oxidized billet sur-
ture. face, mainly with Al2O3, does not act as a lu-
Aluminum-bronzes are corrosion- and oxi- bricant in the container in contrast to copper
dation-resistant alloys because of the formation oxide. The friction resistance is so high that it is
of Al2O3-containing surface layers. They are possible to extrude with a stable shell. Because
also very resistant against erosion-corrosion and the cast billets frequently have surface defects,
cavitation and are particularly suitable for sea- machining is recommended. Testing the cross
water applications. Aluminum-bronzes are also section for cracks and cavities is also advisable.
found in the chemical industry and in highly If the billet heated to more than 750 ⬚C cools
stressed machine components. during extrusion—it can only be extruded rela-
tively slowly—variations in the ␣-b-ratio occur
5.16.7.2 Binary Copper-Aluminum Alloys over the length of the extrusion along with vari-
ous forms of the ␣-phase, resulting in differ-
Materials and Extrudability. The two stan- ences in the mechanical properties.
dardized alloys CuAl5 and CuAl8 have a fcc ␣- As with all difficult-to-extrude materials, a
phase structure. They can be readily cold higher extrusion ratio for the same press power
worked. Their hot workability depends on the can be attained with the aluminum-bronzes by
aluminum content. Figure 5.54 shows the tem- extruding with a lubricated container without a
perature dependence of the hot tensile strength shell through a conical die. This process is used
of the aluminum-bronzes. only in exceptional cases.
The poor extrudability is revealed by the ex- If the aluminum content is 8% or more, then
trusion data in Table 5.9. the structure at the high extrusion temperature
The phase diagram in Fig. 5.53 shows that the above 900 ⬚C consists of an ␣-b mixed structure,
boundary line ␣/␣-b is displaced to higher alu- the flow stress of which is less than the pure ␣-
minum contents with decreasing temperature. structure. However, in the direct extrusion of
The b-content thus decreases during cooling these alloys, there is the risk of flow type C oc-
from the extrusion temperature. Even with nor- curring and the formation of the piping defect at
mal cooling to room temperature from the ex- the end of extrusion in the same way as with
trusion temperature, residues of the bcc b-phase brass. The countermeasures are the same as
are retained with the 8% aluminum-bronze so those mentioned previously; the piping defect
that only limited cold working is possible. If can be controlled by a suitable short billet and
smaller final cross sections are to be produced
long discard. Fracture tests of the ends of the type C similar to CuAl8, so that allowance has
extrusion are recommended in any case. to be made for the piping defect.
Further Processing. The cold workability of
5.16.7.3 Copper-Aluminum Alloys the complex aluminum-bronzes is very re-
with Additions stricted compared with the binary alloys because
of the high b-phase component. They are, there-
(Complex Aluminum-Bronzes)
fore, normally supplied as extruded.
Materials, Structure, and Properties. The Similar to special brasses, the complex alu-
properties of alloys CuAl8Si, CuAl9Mn, minum-bronzes can be heat treated [Ben 93].
CuAl10Fe, CuAl10Ni, and CuAl10Fe3Mn2 are Higher mechanical properties can be obtained
given in the standards. with CuAl10Fe and CuAl10Ni by solution heat
The mechanical, physical, and chemical prop- treatment in the ␣-b-region followed by quench-
erties of the complex aluminum-bronzes depend ing and age hardening at 500 to 650 ⬚C. On
on the composition. The aluminum-bronzes with quenching a b⬘-martensite forms that partly
iron, manganese, and silicon additions are usu- breaks down on aging. The quenching can take
ally extruded in the b-phase where they have a place at the press, but better values are obtained
lower flow stress than CuAl8 (see Fig. 5.54). On by a separate heat treatment after extrusion.
the other hand, CuAl10Ni has an extremely high
flow stress (about 70% higher than CuAl8 at 700 5.16.8 Extrusion of Copper-Nickel Alloys
⬚C). This alloy is extremely difficult to extrude.
Extrusion of Complex Aluminum-Bronzes.
Complex aluminum-bronzes have a strong ten- 5.16.8.1 Materials, Structure,
dency to stick to the container wall. In contrast Properties, and Applications
to brass, the shear stress needed to shear away The copper-nickel alloys contain between 4
the shell is very high at the extrusion tempera- and 50% nickel, usually approximately 5 to
ture of 600 to 700 ⬚C. The related high stem load 30%. Nickel forms a continuous solid solution
needed to shear the shell and the high flow stress with copper (see Fig. 5.55) so that all copper-
result in the complex aluminum-bronzes being nickel alloys are single phase and have a fcc ␣-
very difficult to extrude in spite of the high b- structure.
phase component. Often, if small cross sections The most important copper-nickel alloys are
have to be extruded there is no alternative to covered by DIN 17664 (ASTM E 75). They are
working with a lubricated container without a CuNi10Fe, CuNi20Fe, CuNi30Fe, and CuNi30
shell and with a conical die entry. Mn1Fe.
A special case in the complex aluminum- The most important alloy technically is
bronzes is the copper-aluminum-nickel-shape CuNi30Fe, which is used for tubes in ship heat
memory alloy (about 13% aluminum, 4% exchangers, seawater desalination plants, and air
nickel) in which the composition, billet pretreat-
ment, and the extrusion conditions have to be
exactly maintained to obtain the desired shape
memory properties [Don 92].
The sticking of complex aluminum-bronzes to
the extrusion tooling can sometimes cause prob-
lems in tube extrusion if the mandrel lubrication
or the mandrel taper is insufficient. The internal
surface of the tube can then exhibit cracks or
flaking.
Another almost typical defect with the com-
plex copper-aluminum alloys is the “wood grain
fracture” attributable to severe gas porosity of
the billet or the inclusion of aluminum oxide
films. The billets therefore have to be carefully
checked (e.g., by penetrant check) for sound-
ness.
The complex aluminum-bronzes in direct un-
lubricated extrusion usually flow according to Fig. 5.55 Copper-nickel phase diagram [Han 58]
Chapter 5: The Production of Extruded Semifinished Products from Metallic Materials / 261
and oil coolers. However, CuNi10Fe alloys also be taken into account when casting the billets
find applications here. Whereas pure binary al- into water-cooled molds or by continuous cast-
loys are used primarily for the production of ing.
coins, the extruded alloys used for other appli- A homogenization heat treatment of the bil-
cations, e.g., condenser tubes, have additions of lets is not considered to be necessary in spite of
iron and manganese to improve the properties. the nickel concentration variations resulting to
These elements increase the corrosion and ero- some degree from the casting process. The bil-
sion resistance and raise the strength as well as lets often have to be machined to remove the
the recrystallization temperature. The DKI in- cast skin.
formation sheet i.14 [DKIf] describes the cop-
per-nickel alloys in detail. (See UNS C/70100
to C/72950 and ASTM B 151.) 5.16.9 Extrusion of Copper-Nickel-Zinc
Alloys (Nickel-Silver)
5.16.8.2 Extrusion of Copper-Nickel
Alloys 5.16.9.1 Material, Structure,
Properties, and Applications
The melting point and recrystallization tem-
perature increase with increasing nickel content, Alloys of copper, nickel, and zinc are referred
and the cold and hot workability decrease. As to as nickel-silver because of their silver color.
can be seen in Table 5.9, the extrusion tempera- The copper content of the technically most com-
ture increases with increasing nickel content. mon alloys can range from 45 to 62% and the
The range is between 850 and 1000 ⬚C and is nickel content 7 to 26%, with zinc forming the
the highest of all the copper extruded alloys. remainder. Alloys suitable for turning and drill-
Figure 5.56 shows the hot strength of the copper- ing with an ␣-b-phase contain up to 2.5% lead
nickel alloys as a function of the temperature. It as a chip breaker similar to brass. Small addi-
does fall within reasonable limits at the high ex- tions of manganese are usual to reduce the risk
trusion temperatures mentioned, but when de- of cracking at high temperatures (“annealing
termining the extrudability, the service life of the cracking”).
tooling plays the decisive role. The copper-nickel-zinc alloys are covered by
Copper-nickel alloys should and can be ex- DIN 17663 (see ASTM B 151).
truded as quickly as possible because of the high Figure 5.57 shows the copper corner of the
extrusion temperature and the associated ther- copper-nickel-zinc system. The solid lines in the
momechanical stressing of the tooling. Usually, phase diagram show the room temperature state;
relatively thick-walled tubes are extruded and the dashed lines apply at 850 ⬚C.
then further processed on cold pilger machines In the majority of the commercial nickel-sil-
and by drawing with intermediate annealing be- ver alloys, the fractions of nickel and zinc are
cause the copper-nickel alloys have good cold-
working properties as a result of their fcc lattice.
Extrusion is usually carried out with a shell
and without container lubrication through flat
dies. This is not possible if small cross sections,
i.e., a high extrusion ratio, have to be extruded
in these difficult-to-extrude alloys. Container lu-
brication is then recommended with extrusion
through conical dies and without a shell. The
resultant significantly lower friction between the
billet and the container enables higher extrusion
ratios to be produced or lower extrusion tem-
peratures to be used. However, attention has to
be paid to having a high-quality container bore
and a good billet surface to avoid defects on the
surface of the extrusion.
The increase in hydrogen solubility with in-
creasing nickel content and thus the risk of gas Fig. 5.56 Hot tensile strength curves of copper-nickel alloys
porosity with inadequate melt treatment has to and SF-Cu [Wie 86]
262 / Extrusion, Second Edition
5.16.9.2 Extrusion of Nickel-Silver Alloys Fig. 5.58 Hot tensile strength curves of copper-nickel-zinc
alloys and SF-Cu [Wie 86]
The extrusion data for the nickel-silver alloys
is also given in Table 5.9. As with the brasses
the b-component determines the hot and cold cracking, and a structure with an excessive grain
workability of the different alloys. A lead addi- size.
tion hardly reduces the hot workability of the b- The billet surface of the nickel-silver alloys is
containing nickel-silvers but reduces it signifi- usually turned off and extrusion is carried out
cantly in the ␣-alloys. The hot tensile strength with a thin shell. Because a defect-free section
can be obtained from Fig. 5.58 for some Cu-Ni surface requires the lowest possible extrusion
alloys. These alloys can be readily extruded in temperature, it is frequently possible to extrude
the temperature range between 600 and 700 ⬚C. only with a large cross section, i.e., a low-extru-
In principle, the lowest possible extrusion tem- sion ratio. Further processing is then carried out
perature should be used to avoid oxidation, hot by rolling and drawing.
Chapter 5: The Production of Extruded Semifinished Products from Metallic Materials / 263
5.16.9.3 Competition from Wire Casting With extrusion temperatures of 850 to 1150
⬚C, the extrusion process largely corresponds to
Lead-free nickel-silver is—similar to tin-
that of iron and nickel alloys. Titanium alloys
bronze—occasionally cast in wire format and
are, therefore, usually extruded on steel extru-
then cold worked without hot working. This pro-
sion presses. An analogous technology is used.
cess is economically superior to the manufacture
Similar to steels and nickel alloys forging, hot
of wire by extrusion but frequently produces de-
and cold rolling are preferred when possible to
fects in the strand, which reduce the quality
the more expensive extrusion process for the
[Bau 76].
production of bar material of titanium. Thin-wall
tube in unalloyed titanium is also usually made
from strip with longitudinal welding. Extrusion
is, however, the most suitable method of pro-
duction for thick-wall titanium tubes, titanium-
alloy tubes, and for sections.
Extrusion of
Semifinished Products in
5.17 Materials, Their Properties,
Titanium Alloys and Applications
Martin Bauser* 5.17.1 The Structure and Its
Influence on the Properties
Titanium with a melting point (Ts) of 1668 ⬚C
is one of the high-melting-point metals. Al- The example of the phase diagram for tita-
though it is the fourth most abundant metal in nium with aluminum (Fig. 5.59) shows that pure
the earth’s crust after aluminum, iron, and mag- titanium has a close-packed hexagonal lattice up
nesium, the high cost, in particular, of the re- to 882 ⬚C, the so-called ␣-phase. Above this
duction to the pure metal but also of casting and there is the bcc b-phase. In alloys there is a more
further processing, makes titanium products ex- or less wide field within which the ␣- and b-
pensive [Sib 92]. Its low density of 4.5 g/cm3 phases can coexist.
compared with iron and, simultaneously, the Titanium alloys are classified into three
very high strength of some of its alloys makes groups according to the structure at room tem-
it particularly useful where a favorable ratio of perature after the most common deformation
strength to density is required, i.e., in the aero- and heat treatment processes: ␣-alloys, ␣-b-
space industry. The very good corrosion resis- alloys, and b-alloys.
tance against numerous media is attributable to b-alloys in general have a lower strength and
the strongly adhering oxide film that forms even elongation as well as an inferior fatigue perfor-
at room temperature. It therefore finds numerous mance compared with the ␣-b-alloys. However,
applications in the chemical and petrochemical the b-alloys are superior to the ␣-b-alloys in
industries. Titanium alloys can be classified as terms of creep strength and fracture toughness
one of the exotic extruded metals because of the [IMIa 88].
high cost. Because its industrial application only The ␣-alloys are relatively difficult to work at
started in the 1950s, all production and appli- room temperature [Mec 80], whereas b-alloys
cation possibilities have certainly not been ex- can still be readily deformed.
hausted. The alloying constituents of the technically
Special mention should be made of supercon- most important materials are aluminum, which
ductors of titanium-niobium alloys, shape-mem- increases the strength and stabilizes the ␣-phase,
ory alloys with titanium and nickel as the main as well as chromium, manganese, molybdenum,
constituents, as well as intermetallic phases of vanadium, copper, tin, and zirconium. Most of
titanium and aluminum for high-temperature ap- these elements stabilize the b-phase and reduce
plications. The book Titanium and Titanium Al- the ␣/b transformation temperature and are con-
loys by U. Zwicker gives an overview [Zwi 74]. tained in the precipitates after age hardening. Tin
as an alloying element, which slightly stabilizes
the ␣-phase, and zirconium have a high solubil-
*Extrusion of Semifinished Products in Titanium Alloys, ity in the ␣-phase and harden it [Mec 80]. Zir-
Martin Bauser conium increases the hot and creep strengths.
264 / Extrusion, Second Edition
The undercooling capability of the b-phase The strength is not a decisive criterion for
and the reducing solubility with the decreasing thin-wall tube for liquid transport in the chemi-
temperature of numerous alloying elements re- cal or petrochemical industry and, for example,
sult in interesting hardening and tempering pos- in water desalination plants and power station
sibilities. Solution heat treatment is usually car- cooling towers. The requirement is far more for
ried out in the b-region or just below followed the outstanding corrosion resistance of titanium
by rapid cooling so that the ␣-phase or other against a range of media and its oxidation resis-
precipitates can form only in a finely distributed tance at normal temperatures. In these applica-
manner after subsequent age hardening. Age tions different grades of pure titanium are used
hardening cannot be carried out on ␣-materials that differ from each other only in their oxygen
[Lam 90]. content (Table 5.13).
The often complicated transformation kinetics As with iron alloys the move is away from the
of the ␣-b alloys are represented in time-tem- production of soft tubes by extrusion, cold pilger
perature-transformation diagrams similar to mills, and tube drawing. This area has had to be
steel [Zwi 74]. conceded to the more economic longitudinal
The lowering of the transformation tempera- welding of cold-rolled strip.
ture by b-stabilizing additions is important for Bar and section in commercially pure tita-
hot working because the body-centered cubic b- nium can be extruded and is produced by this
phase has better forging and extrusion properties route but the demand is small.
than the hexagonal ␣-phase. The aerospace industry is the main user of
The niobium-titanium alloy with 52% Nb and semifinished products in titanium alloys apart
48% Ti used for superconductors has a relatively from special products, including racing wheels
low transformation temperature and can there- and sports cars. In aircraft, they are used for en-
fore be extruded at approximately 900 ⬚C. gine components, fuselage, and wing elements
[Pet 92] (Table 5.13). Wherever the strength and
5.17.2 The Most Important
mechanical properties of aluminum alloys are
Titanium Alloys and Applications insufficient, titanium alloys are used for light-
Table 5.13 shows the most important titanium weight fabrications.
alloys with their properties and application Extruded sections, tubes, and bars are pro-
areas. duced from the higher-strength materials as well
Table 5.13 Some titanium alloys suitable for extrusion, properties, and applications (IMIa 88, IMIb 88, and personal communication)
Low-temperature alloys
Structure at Strength Elongation,
Material Composition room temperature Rm, N/mm2 A5, % Properties Application
Ti1– Ti3(a) Unalloyed titanium with min 99–99.5% Ti ␣-phase 290–590 30–8 Corrosion resistant, readily worked Tubes and components for the chemical and
petrochemical industries
Ti1Pd–Ti3Pd(a) Addition of 0.12–0.25% Pd ␣-phase 250–590 30–8 Very corrosion resistant The same areas
Intermediate temperature alloys
Composition
Material Cu Al V Sn Mo Si Structure at room temperature Strength Rm, N/mm2 Elongation, A5, % Properties Application
TiCu2.5 (IMI 230)(c) 2.5 ... ... ... ... ... ␣-Phase 630–790 ⬎30 Used up to 350⬚C, soft Gas turbines
Age-hardening readily worked Aircraft components
TiAl6V4(b) (IMI 318)(c) ... 6 4 ... ... ... ␣-b-mixed structure 950–1080 ⬎12 Used up to 500⬚C Most common alloy,
Quenched and tempered Creep resistant up to turbines, jet engines,
Fine ␣ in b structure 300⬚C implants
Suitable for hot-working
TiAl4Mo4Sn2 (IMI 550)(c) ... 4 ... 2 4 0.5 ␣-b-mixed structure used 1000–1250 ⬎9 Creep resistant up to Jet engines
heat-treated and tempered 400⬚C Aircraft components
TiAl6V6Sn2(a) ... 6 6 2 ... ... ␣-b-mixed structure 1000–1300 ⬎8 Creep resistant up to Aircraft components
500⬚C
Materials for High-temperature alloys
Composition
Material Al Sn Zr Mo Si Nb Structure at room temperature Strength Rm, N/mm2 Elongation, A5, % Properties Application
IMI 679(d) 2 11 5 1 0.2 ... ␣-b-mixed structure with ⬎1100 ⬎8 Creep resistant up to 450 Aerospace
precipitates; high- ⬚C, still suitable for
temperature heat hot working
treatment; b with
precipitates
6242(d) (USA) 6 2 4 2 ... ... Almost ␣ ⬎900 ⬎10 Creep resistant up to 500 Aerospace
⬚C
IMI 829(d) 5.5 3.5 3 0.25 0.3 1 Almost ␣ ⬎9 Creep resistant up to 940 Gas turbines
⬚C
(a) DIN 17850/17861/17862. (b) DIN 17851/17961/17862. (c) IMI brochure: Titanium Medium Temperature Alloys. (d) IMI brochure: Titanium High Temperature Alloys.
Chapter 5: The Production of Extruded Semifinished Products from Metallic Materials / 265
266 / Extrusion, Second Edition
as sheet and strip. The alloy TiAl6V4 is the most 700 ⬚C and can become brittle in hydrogen-con-
common not only as a construction material be- taining atmospheres. Very fast heating is op-
cause of its high strength, but also in surgery for posed by the poor thermal conductivity of tita-
implants because of its good biocompatibility. nium. Heating in a salt bath (e.g., with barium
chloride as a deoxidant) is less environmentally
5.17.3 Titanium Alloys Produced by friendly and is therefore rarely used.
Powder Metallurgy
Titanium alloys produced by powder metal- 5.18.2 Extrusion, Lubrication
lurgy (P/M) are being offered to an increasing Table 5.14 shows the important data for the
extent. This occurs on one hand when high-alloy extrusion of titanium alloys produced by melting
materials, e.g., with intermetallic titanium alu- metallurgy.
minide, cannot be produced by melting metal- Titanium alloys are preferentially extruded in
lurgy or cannot be or only to a limited extent be the b-phase region where the flow stress is sig-
hot worked and, on the other hand, if it is dis- nificantly lower than in the ␣-b mixed region (or
persion-hardened material in which the disper- in the pure ␣-phase). The uniform structure,
soids can only be added to the metal using P/M. which is obtained by the recrystallization that
These materials are described in Chapter 4. occurs during extrusion in the b-region, is also
advantageous. If the temperature in the b-region
is too high, there is the risk of coarse grain for-
5.18 Billet Production, Extrusion mation, which has to be avoided at all costs.
With some alloys it is possible to obtain a mar-
5.18.1 Casting, Billet Preparation, tensitic structure if the section is not cooled
slowly enough from the b-phase. Subsequent
Billet Heating
annealing is then required.
The billet pre-material is usually obtained Because titanium becomes brittle not only in
from vacuum arc furnaces with melting elec- hydrogen but also nitrogen and oxygen atmo-
trodes of titanium foam and recycled material spheres, the extrusion temperature should be as
[Kra 82]. If the ingot diameter is too large, it has low as possible without crossing the ␣/b tem-
to be forged to the final billet diameter. This has perature limit.
the advantage that an originally coarse grain If, on the other hand, deformation is carried
structure with low hot workability can be re- out just below the ␣/b phase boundary, the var-
crystallized with a fine-grain structure by careful iations in heating during extrusion over the cross
selection of the forging temperature intervals. section and along the length of the section result
Mechanical surface processing is the final in a changing mixed structure that produce var-
stage: a smooth billet surface is the requirement iations in materials properties over the cross sec-
for a good product surface in the same way as tion and along the length.
with steel extrusion because in direct extrusion Titanium alloys are extruded in the tempera-
without a shell, with lubrication and a conical ture range 850 to 1150 ⬚C. Above 1000 ⬚C,
die entry, the billet surface becomes the product which is in the b-region, it is necessary to use
surface. glass lubrication similar to steel and nickel
The billets have to be rapidly heated in an alloys.
induction furnace or a protective atmosphere The glass film hinders the contact between the
(argon) because titanium easily oxidizes above titanium material and the extrusion tooling and
Table 5.14 Data for the extrusion of some titanium alloys (Lau 76, Zwi 74, IMI personal
communication)
Alloy b-phase boundary Extrusion temperature Structure at extrusion temperature Deformation at extrusion temperature
Ti 1–Ti 882 ⬚C 700–900 ⬚C ␣-phase
TiAl6V4 995 ⬚C 900–950 ⬚C ␣-b-phase ⬃120 N/mm2
1050–1100 ⬚C b-phase ⬃80 N/mm2
TiAl6VSn2 945 ⬚C 800–1040 ⬚C ␣-b or b-phase
TiAl4Mo4Sn2 975 ⬚C ⬃900 ⬚C ␣-b-phase ⬃160 N/mm2
⬃1100 ⬚C b-phase 100 N/mm2
TiAl6Sn3Zr3MoNbSi 1015 ⬚C 1050–1150 ⬚C b-phase ⬃100 N/mm2
Chapter 5: The Production of Extruded Semifinished Products from Metallic Materials / 267
thus the destruction of the bearing surfaces by The pickling away of the copper film in a mix-
corrosion, to which titanium tends in contact ture of nitric and hydrofluoric acid is unpleasant
with steel. The molten glass also acts as a ther- and is the reason why cladding in copper is
mal insulation barrier and hinders the heat flow avoided as much as possible. It has been re-
from the hot material into the colder tooling. The ported that an extrusion in the ␣-b-mixed region
glasses 4 and 5 for the lower temperature range is possible without a copper cladding in spite of
are preferred from the recommended glass the severe adhesion tendency between titanium
mixtures for stainless steel tubes (see Table 5.18 and the tooling surface if a special graphite
and [Mar 74]). grease lubrication is used [Boy 89].
The extrusion technology with titanium alloys
differs slightly from that for iron-base alloys: ti-
5.18.3 Flow Stress, Extrusion Defects
tanium alloys are, if possible, coated with a glass
powder suspension at 80 to 150 ⬚C. During the Compared with many stainless steels, the ti-
subsequent heating to the extrusion temperature, tanium alloys have a high flow stress at the ex-
the glass coating can act as a barrier against the trusion temperatures mentioned, and they are
reaction of the billet surface with air constituents therefore difficult to extrude (see Fig. 5.60). This
[Mar 74]. means that on a press usually used for extruded
However, the method described for stainless semifinished products in steel, titanium can be
steels, rolling the billet heated to the extrusion extruded only with a low deformation. Extrusion
temperature over a table in glass powder is com- ratios of V ⳱ 10 to V ⳱ 100 are used.
mon, particularly with tube extrusion and when The flow stress is—particularly in the ␣-b-
induction furnaces are available for heating. mixed region—very temperature dependent: It
Extrusion is usually carried out quickly, di- increases rapidly with falling temperature as
rectly through a die with a conical entry with a shown in Fig. 5.60. Care must therefore be taken
glass disc in front to minimize the cooling of the to ensure that the billet is not given time in the
material during the extrusion process and to en- container to cool, producing a large radial tem-
sure that the tooling is subjected to the high tem- perature gradient. Otherwise, the material from
peratures for only a short time. At a high speed
the temperature of the emerging section can
even increase from the front to the back.
If the speed is too high, in particular with sec-
tions, there is the risk that the glass film will tear.
The instantaneous failure of the tool working
surfaces is the result [Mar 74]. The extrusion
speed is in the range 0.5 to 5 m/s.
There are also alloys that have to be extruded
in the ␣-b-mixed region with temperatures be-
tween 700 and 950 ⬚C, especially if subsequent
cold working is not carried out and a fine-grain
structure is needed in the as-extruded condition
[Zwi 74]. The turned billet is then wrapped in a
thin copper sheet and extruded with a lubricated
container, in this case, a graphite grease mixture,
through conical dies. At the upper temperature
range of 850 to 950 ⬚C, an iron foil is recom-
mended as an intermediate layer to avoid a re-
action between the copper and the titanium.
With adequate lubrication the friction be-
tween the billet and the container is, similar to
glass lubrication, so low that a quasi-stationary
deformation with laminar material flow occurs,
and the surface copper layer at the start and end
of the section has an approximately constant
thickness. This would be even better with indi-
rect extrusion, but usually only direct extrusion Fig. 5.60 Flow stress kf as a function of the temperature
presses are available. [Zwi 74]
268 / Extrusion, Second Edition
the billet interior will flow first producing a pip- bium (ZrNb2.5) are used as construction mate-
ing defect at the end of the section. If the extru- rials in nuclear reactors, especially for the casing
sion is too slow there is also the risk of the bil- material for the fuel rods because of the low ab-
let’s “sticking.” sorption of thermal neutrons, good heat transfer,
The dependence of the flow stress on the rate good corrosion resistance, and high hot strength.
of deformation is higher for titanium than for The chemical industry also uses zirconium-alloy
steel. Nevertheless, extrusion has to be carried semifinished products for specific critical cor-
out quickly for the reasons just mentioned. rosion conditions.
The production of the very pure metal nec-
essary for processing is costly, and zirconium
5.19 Tooling, Further Processing alloys are therefore correspondingly expensive.
Zirconium melts at 1852 ⬚C and has a density
The tooling is discussed in Chapter 7 in the of 6.5 g/cm3. Pure zirconium has a hexagonal ␣-
section on tooling for the extrusion of titanium lattice up to 862 ⬚C. Above this transformation
alloys. temperature, there is a bcc b-phase. With al-
The tooling loading is similar to the extrusion loys—also with small quantities of element ad-
of stainless steels. When extruding in the b- ditions—there occurs a more or less wide tem-
region with glass lubrication—particularly in perature interval with the simultaneous presence
section extrusion—only one or two billets can of the ␣- and the b-phases [Web 90]. The struc-
be extruded before the die has to be reworked. ture is similar to that described for titanium al-
The die service life is significantly longer with loys, and the properties during hot and cold
copper sheathed billets and lower extrusion tem- working are comparable.
peratures. Chapter 7 describes coated section
dies that are much more expensive but have a
significantly longer service life. 5.21 Billet Production, Extrusion
Normally, the lowest limit for the wall thick-
ness of sections is 2 mm. Sections used in air- 5.21.1 Casting, Billet Preparation
craft construction often have to have thinner
walls (down to 1 mm wall thickness). Because Similar to titanium production, the starting
cold working of the common alloys is possible material is melted from zirconium sponge in
only to a limited extent, drawing and stretching vacuum or protected atmosphere furnaces with
of the extruded sections at a higher temperature self-consuming electrodes. After forging or roll-
is utilized [Mar 74]. However, 350 ⬚C should not ing the large-diameter cast ingots, the billets for
be exceeded to avoid undesired structural the extrusion of tubes have to be turned on the
changes. outside to remove surface defects and also be
prebored. Because zirconium has the same prop-
erty as titanium of readily welding to the tooling
during deformation and also reacts with oxygen,
hydrogen, and nitrogen at high temperature, the
Extrusion of billets are normally externally and internally
clad. Copper sheet material is usually used
Semifinished Products in sometimes with an intermediate steel layer when
Zirconium Alloys the temperature is high to prevent diffusion of
the copper into the zirconium base material. The
copper cladding can, however, be applied by
Martin Bauser* plasma spraying. To avoid an expensive zirco-
nium discard, a copper disc can be attached to
5.20 Materials, Properties, the back of the billet to form the discard, at the
and Applications end of extrusion. The cladding of the billet can
be avoided by using special lubricants.
Pure zirconium and, in particular, zirconium
alloys with tin (ZrSn1.5 ⳱ zircaloy) and nio- 5.21.2 Extrusion, Influence
of the Structure
*Extrusion of Semifinished Products in Ziroconium Alloys, If zirconium, for which there is no great de-
Martin Bauser mand, is processed on presses installed for steel
Chapter 5: The Production of Extruded Semifinished Products from Metallic Materials / 269
or copper alloys, then the technology used fol- If extrusion is carried out with copper clad-
lows that for the corresponding main material. ding, the cladding material has to be removed
The flow stress of most zirconium alloys is from the extruded product either mechanically
not very high at the extrusion temperature, and or with nitric acid. Zirconium is not attacked by
the dependence on the temperature is tolerable nitric acid. Coarse grain billet material leaves an
so that the extrusion temperature and speed can orange peel effect on the pickled surface as an
be varied within relatively wide boundaries with image of the grain structure. A fine-grain start-
no risk. ing material is therefore preferred.
Because the b-phase has the best hot work- The subsequent processing of zirconium alloy
ability, it makes sense from the deformation tubes is carried out on precision cold pilger ma-
point of view to extrude in the temperature range chines [Jun 93]. Drawing requires careful prep-
800 to 1100 ⬚C, where the flow stress is rela- aration by bonderizing and lubrication because
tively low. This, however, rarely occurs because the material has a tendency to weld to the tool-
the billets would then have to be clad in steel. ing. More recently, drawing has been carried out
In this case, lubrication is carried out with a using an ultrasonic vibrating mandrel, which im-
glass powder mixture similar to steel and tita- proves the internal surface. Zircalloy cladding
nium. for fuel rods can be produced from extruded
In practice zirconium alloys are extruded tubes without drawing by multiple cold pilger
preferentially in the temperature range 675 to operations with intermediate annealing (70% re-
800 ⬚C to reduce the risk of gas absorption, duction per cycle can be achieved).
which severely impairs the toughness of the ex-
truded semifinished product. Just below the ␣/b
transformation temperature and (in the case of
alloys) in the ␣-b mixed phase region the work-
ability is very good [Sch 93].
The best method, but also the most expensive, Extrusion of Iron-Alloy
is cladding the billets in copper. Clad billets can
be heated in an induction furnace and lubrication
Semifinished Products
with oil-graphite suffices similar to standard
copper alloys. Dies with conical entries are nec- Martin Bauser*
essary to obtain a predominantly laminar flow
and thus to obtain a uniform cladding thickness
over the length of the extrusion. 5.23 General
If extrusion is carried out without cladding, it
is important that the billets are brought rapidly 5.23.1 Process Basics
to temperature and protected as far as possible
from atmospheric influences during heating. Salt The high melting point of iron alloys (pure
bath heating is, therefore, preferred over other iron: 1535 ⬚C, density 7.9 g/cm3) corresponds to
methods (75% BaCl, 25% NaCl is referred to in a high recrystallization and hot-working tem-
[Lus 55]). perature. Hot working usually is carried out in
Special glass mixtures are used as lubricants the fcc austenite region, depending on the alloy,
when extruding without cladding at approxi- between 1000 and 1300 ⬚C. This is associated
mately 800 ⬚C. They have a low viscosity even with high tool wear because of the high thermal
at this low temperature and substantially protect and mechanical stresses and, depending on the
the billets from gas absorption. composition, a more or less severe oxide for-
mation. As a result, it was relatively late before
these alloys could be successfully extruded.
5.22 Tooling, Further Processing The oil graphite lubricants known from cop-
per alloys, and which were used for steel extru-
When selecting the tooling materials and the sion around 1930, were not really suitable. They
tooling design, the experience gained from the were initially replaced with mixtures of oil,
extrusion of copper alloys and—when extruding graphite, and cooking salt, which could be ef-
at high temperatures—of steels can be utilized.
As a general rule, conical dies (2␣ ⳱ 140 to *Extrusion of Iron-Alloy Semifinished Products, Martin
90 ⬚C) are used to produce tubes and round bars. Bauser
270 / Extrusion, Second Edition
fective only with very short contact times be- uneconomic. The tooling costs can also be
tween the hot material and the shape-forming very high. In contrast, extrusion can be via-
tooling. This method of lubrication is used only ble for quantities as low as three billets.
rarely today for the production of mild steel ● Experimental or pilot production of tubes
tubes on vertical mechanical presses (see section and sections that will later be produced in
5.24). large quantities more economically by
A significant extension to the application of rolling
the extrusion process followed the development
of the Ugine-Séjournet process in 1950 in which Approximately only 30% of all steel tubes are
glass of a specific composition was used for lu- produced as seamless and of these, less than
brication [Séj 56]. The molten glass not only 10% are produced by extrusion [Bil 79].
protects the heated billet from oxidation and acts Three product groups are described in detail
as a lubricant between the material and the tool- subsequently:
ing, but also acts as thermal insulation so that ● Mild steel tubes
the die and container heat more slowly than with ● Alloy steel tubes
the lubricants previously used. It was now pos- ● Steel sections
sible to produce alloy steel tubes and steel sec-
tions on horizontal extrusion presses with a lu-
bricated container.
Steels are extruded using the direct extrusion 5.24 Mild Steel Tubes
process with lubricated containers without a
shell. With this process it is possible to achieve
short contact times with fast extrusion speeds— 5.24.1 Use of Mechanical Presses
important for the necessary high extrusion tem- The numerous vertical mechanical presses
peratures. The use of conical dies result in a ma- previously used in the technically highly devel-
terial flow in which the billet surface forms the oped countries are no longer in operation. Car-
surface of the extruded product (see Chapter 3, bon steel tubes are usually produced on contin-
the section on material flow in direct extrusion, uous production lines that have a significant
Fig. 3.31). higher productivity. However, these mechanical
presses are still used in other countries.
5.23.2 Importance of Carbon steels, free cutting steels, low alloy
Steel Extrusion Today hot and cold working steels and high speed
steels can be processed on mechanical presses.
The growth in the extrusion of steel in the
1950s and 1960s was followed by a continuous
decline. The production of seamless tubes in
mild steels and low-alloy structural steels on 5.24.2 Application of Mechanical Presses
vertical presses has largely been replaced by
Mechanical extrusion presses are similar to
more economic continuous rolling processes.
the machines used in the drop-forging industry.
Seamless tubes in these steel grades are now re-
The billets are pierced and extruded in one
placed whenever possible by the less-expensive
operation on vertical mechanical presses. The
longitudinally welded tubes.
billets are first heated to 1100 to 1300 ⬚C and
Today, the extrusion of stainless steel tubes
loaded into the vertical lubricated container.
and steel sections is used only when the material,
Then, at the upper top dead center the crankshaft
the section shape, or the low volume required
is connected to a continuously operating electri-
cannot be produced by other processes or only
cally driven flywheel with a horizontal axis. In
with significant expense.
one revolution the stem and piercing mandrel
The reasons for extruding steel tubes are:
fall and the billet is extruded down into a curved
● Crack-free production of long products even channel and the stem and mandrel retracted. The
in materials that are difficult to hot work and discard is sheared with a shearing tool and re-
that tend to crack during rolling moved from above.
● Production of small volumes. If unusual di- The high deformation temperature and the ex-
mensions or materials are involved, then fre- trusion time, which lasts for only a few seconds
quently the setting and operation of rolling on the mechanical press, enables extruded tubes
processes designed for mass production is in mild and free-cutting steels to be hot reduced
Chapter 5: The Production of Extruded Semifinished Products from Metallic Materials / 271
directly after extrusion on a stretch reducing mill Table 5.15 Production ranges for the different
without reheating. methods for producing seamless steel tubes
The glass lubrication used on horizontal (Man 86)
presses to protect the tooling (see section Process Tube diameter, mm
5.25.4.2) is not really applicable for vertical Extrusion 35–250
presses because the glass powder does not ad- Tube continuous rolling 20–180
Diagonal rolling and Pilger process 160–660
here securely to the billet surface in the vertical Plug rolling procedure 180–400
position.
The older method of lubrication with a vis-
cous oil-graphite salt mixture has to be used.
This partly evaporates and can even burn during for extrusion can be produced relatively inex-
pensively but wear much more rapidly than the
extrusion. Today’s environmental requirements
tooling in the rolling process.
are difficult to fulfill even with careful extrac- The most important method of producing
tion. seamless alloy steel tubes in the same dimen-
sional range as the extrusion press is the contin-
5.24.3 Dimensional Range and uous tube-rolling process in which a forged
Throughput round ingot formed to a hollow billet in a pierc-
ing mill is hot rolled over a mandrel through
Mechanical tube presses are restricted in their numerous profiled roll pairs and then brought to
press loads because there is a limit to the load the finished size on a stretch reducing mill after
that can be economically transferred mechani- reheating. This process has at least 4 times the
cally. They are, therefore, used only for extru- throughput of an extrusion press [Bil 79].
sion loads up to a maximum of 17 MN. Because The extrusion process today is restricted to:
the upper limit of the billet weight naturally de- ● High-alloy stainless ferritic and austenitic
pends on the extrusion load that can be devel- steels
oped, the maximum billet weight that can be de- ● Heat-resistant high-chromium ferritic and
formed is 120 kg with a diameter of 200 mm. austenitic alloy steels
The entire extrusion process lasts no longer ● High-temperature austenitic alloy steels
than 3 s so that it is possible to have up to 200
working cycles in one hour (average 120 to The dimensional range of these tubes is be-
tween 35 and 250 mm external diameter and a
130). The mandrel length is restricted to 5 to 7
wall thickness of 5 to 50 mm with a minimum
times the mandrel diameter because longer man- internal diameter of 30 to 40 mm [Ric 93]. The
drels can deflect sideways within the press dur- extruded tubes are usually processed further by
ing piercing. rolling and/or drawing.
The dimensional range of the extruded tubes To produce the infrequently required dimen-
extends from 40 to 120 mm external diameter sions over 200 mm external diameter, an alloy
and 2.5 to 5 mm wall thickness [Sar 75]. steel tube extrusion press would have to be so
massive that the high cost would generally pro-
hibit the use of the extrusion process [Bil 79]. A
5.25 Seamless Alloy Steel Tubes 55 MN press designed for this purpose was sup-
plied to Russia several years ago.
Horizontal water-driven tube presses and only
5.25.1 Extrusion in Competition with the direct process without a shell are used. Fig-
Other Hot-Working Processes ure 5.61 shows the extrusion principle.
There has also been a large reduction in the Alloy steel tubes produced by extrusion are
extrusion of seamless alloy steel tubes over the sold as hot finished or further cold worked. Ap-
plications are in the chemical industry, plant
last few decades and numerous presses have had
manufacture, nuclear technology, and the pet-
to be closed down. The extrusion of seamless rochemical industry.
alloy steel tubes has to compete with a range of
more economic rolling processes, the production 5.25.2 Alloys and Extrusion Properties
capacity of which can be seen in Table 5.15.
Economic analysis has shown that extrusion 5.25.2.1 Alloy Groups, Structure,
is inferior in output to the continuously operat- Properties, and Applications
ing rolling processes because of the low billet Table 5.16 shows a selection of the alloy
weight and the long dead cycle times. The dies steels currently extruded.
272 / Extrusion, Second Edition
Fig. 5.61 Extrusion of alloy steel tubes on a horizontal press [Sar 75]
Table 5.16 Examples of stainless heat-resistant and high hot strength steels that are processed by
extrusion (Ric 93)
Chemical composition, %
Material No. C Cr Ni Mo Other Similar UNS No./Common Name
Stainless steel
Ferritic ... ... ... ... ... ...
1.4016 ⬍0.08 16.5 ... ... ... S43000/430
1.4510 ⬍0.05 17.0 ... ... Ti⬎4 ⳯ (CⳭN) ⬍ 0.8 S43036/430Ti
Austenitic
1.4301 ⬍0.07 18.0 9.5 ... ... S30400/304
1.4306 ⬍0.03 19.0 11.0 ... ... S30403/304L
1.4401 ⬍0.07 17.5 12.0 2.2 ... S31600/316
1.4404 ⬍0.03 17.5 12.5 2.2 ... S31603/316L
1.4571 ⬍0.08 17.5 12.0 2.2 Ti⬎5 ⳯ %C ⬍ 0.7 S31635/316Ti
Heat-resistant steels (austenite)
1.4845 ⬍0.15 25.0 20.5 ... ... S31000/310
1.4841 ⬍0.20 25.0 20.5 ... Si 2.0 S31400/314
1.4876 ⬍0.12 21.0 32.0 ... Ⳮ Al Ⳮ Ti
High-temperature steels (austenite)
1.4910 ⬍0.04 17.0 13.0 2.5 N 0.14 S31653/316LN
1.4961 ⬍0.10 16.0 13.0 ... Nb 10 ⳯ %C ⬃ 1.20 S34700/347
1.4959 0.07 20.0 32.0 ... Al Ⳮ Ti, V 0.07 ...
The heat-resistant materials are covered by notch impact values. Suitable billets for ex-
DIN EN 10095, the other materials by DIN EN trusion are therefore difficult to produce free
10216-5 and DIN 17456 (the European standard from cracks in the high-chromium-contain-
[EN] has replaced the previous DIN standards). ing materials.
The following material groups are classified Hot-brittle lead and sulfur-containing
by the hot-working temperature range [Ric 93]: free-machining steels can only be hot rolled
with difficulty. Only piercing and rolling
● Ferritic steels with bcc ␣-iron structure. All over a mandrel are suitable for processing
ferritic chromium steels over 12% Cr content these alloys apart from extrusion, which is
as well as the steels alloyed with molybde- still the most common process used for this
num and/or titanium belong to this group and material group.
have a bcc ␣-iron structure. They are char- ● Austenitic steels have chromium contents
acterized by a flow stress that decreases rap- over 16% and nickel contents exceeding 8%.
idly with increasing temperature so that they At the extrusion temperature the structure of
can be readily hot worked. these alloys is the fcc c-iron lattice. The aus-
However, this alloy group tends to brittle- tenite is, therefore, usually characterized by
ness due to precipitated phases and to grain very good hot workability as well as a low
coarsening during the hot working of the tendency to embrittlement. The undesirable
starting material by rolling or forging before coarse grain formation found with the ferritic
extrusion. The embrittlement reduces the steels does not occur with the austenitic ma-
Chapter 5: The Production of Extruded Semifinished Products from Metallic Materials / 273
terials so that they can also be readily mium and nickel content. The effect of other al-
welded. loying elements is determined from their chro-
The good workability and the good cor- mium or nickel equivalent.
rosion resistance against many media pro- In austenitic steels, d-ferrite is particularly
vide the austenitic materials with a wide dangerous because its occurrence limits the
range of applications in chemical plant man- extrusion temperature; otherwise, transverse
ufacture and in energy production. cracking occurs in the extruded section.
The higher the nickel content, the higher
is the hot strength of austenitic materials and 5.25.2.2 Extrusion Properties, Defects
the more difficult they are to extrude. High-
nickel-containing materials can conse- The extrudability and extrusion temperature
quently be extruded only at low extrusion range of the different materials are given in Ta-
ratios. ble 5.17.
● Austenitic–ferritic alloys with chromium The fewer the precipitates, the better the ex-
contents of 18–25% and nickel contents of trudability of ferrite and austenite. Single-phase
4–7% are used for a range of applications. materials—particularly in the c-range with a fcc
They combine to some extent the advantages structure—are particularly easy to extrude [Bur
of both the alloy groups described previ- 70, Ben 73].
ously. They have a lower susceptibility to At the normal extrusion temperatures of 1100
embrittlement than do ferritic materials and to 1350 ⬚C, the flow stress is in the range 150
are more easily worked than the austenitic MPa (materials with high extrudability) to 400
materials and also offer advantages in spe- MPa (materials with low extrudability) for aus-
cific types of corrosion attack. The most tenite and ferrite. The extrusion ratio (V) is usu-
well-known representative of this group is ally 8 to 40.
the material 1.4462 with 22% Cr, 5.5% Ni, Examples of the relationship of the flow stress
and 3% Mo, which is an alloy steel with and the deformation capability on the composi-
many applications in the petrochemical in- tion and the temperature are shown by the curves
dustry. for different steels in Fig. 5.63.
Whereas the workability of homogeneous
An overview of the structure of the three ma- structures always increases with increasing tem-
terial groups is given by the phase diagram ac- perature, a marked decrease can occur with Cr-
cording to Schaeffler-DeLong (Fig. 5.62), which Ni steels as a result of the formation of d-ferrite
shows the structure as a function of the chro- above approximately 1200 ⬚C. This results in a
274 / Extrusion, Second Edition
risk of transverse cracking during extrusion. The stituents that can form precipitates, the extruded
limit is considered to be 2 to 3% d-ferrite at section usually has a fully recrystallized struc-
room temperature (corresponding to approxi- ture.
mately 8% at the extrusion temperature). At low extrusion ratios, i.e., large tube cross-
The calculation of the extrusion load is dis- sectional areas, the core region tends to accel-
cussed in detail in Chapter 3. erate. The resultant internal longitudinal stresses
The high extrusion temperature produces a can result in lamination such as internal cracking
large temperature difference between the mate- within the extruded section that cannot be de-
rial and the container and a rapid loss of heat. It tected externally. These defects can only be dis-
is necessary to extrude quickly to prevent the covered using ultrasonic testing.
billet freezing during the extrusion process. This In contrast, in thin-wall tubes, these stresses
also aids the die life. result in cracks originating at the surface.
In the deformation zone immediately in front
of the die, an adiabatic temperature increase of 5.25.3 Billet Production
up to 150 ⬚C occurs during extrusion. The higher
the flow stress of the material and the faster the 5.25.3.1 Melting, Casting, Hot Working
extrusion speed, then the higher the temperature
Alloy steels are melted today by the following
increase will be, i.e., the closer the process ap-
processes [Ric 93]:
proaches adiabatic conditions. It is therefore
necessary to carefully match the temperature and ● Electric arc melting process with down-
speed for materials with low-melting-point con- stream argon-oxygen-decarburization (AOD)
stituents to avoid melting and thus cracks in the or vacuum-oxygen-decarburization [VOD]
extruded section. ● Induction melting in air or in a vacuum
Because the extrusion temperature is above ● Remelting using the electroslag refining pro-
the solution heat treatment temperature of con- cess (ESR)
Fig. 5.63 Flow stress and workability of steels measured from the number of turns to failure in torsion tests as a function of
temperature. (a) Flow stress. (b) d. (c) Deformation capacity [Ben 73]
Chapter 5: The Production of Extruded Semifinished Products from Metallic Materials / 275
The latter guarantees a high cast purity and an 5.25.4 Billet Heating, Lubrication
extensively homogeneous distribution of the ele-
ments that tend to segregation such as niobium
5.25.4.1 Billet Heating
and molybdenum.
Continuous casting is carried out if the charge Apart from the uniform through heating of the
size permits; otherwise, mold casting is used. billet, it is important during heating to avoid ox-
Only pure and low-alloy carbon steels can be idation and surface decarburization of the heat
directly extruded without previous hot working. treatable steels.
Higher-alloyed materials have to first be forged Billet heating to the required temperature of
or hot rolled to destroy the columnar cast struc- 1100 to 1300 ⬚C is carried out in rotary hearth
ture and produce a homogeneous structure [Man furnaces with protective atmospheres, in induc-
91, Bil 79, Bur 70]. tion furnaces, or in a combination of both with
a gas furnace for preheating to approximately
700 ⬚C and final heating in an induction furnace.
5.25.3.2 Homogenizing, Billet The slower heating in the rotary hearth fur-
nace with its more uniform through heating can
Preparation
have a homogenizing effect on the structure of
Homogenizing of the rolled or forged billets some steels.
is rarely carried out and only when the homo- The cost advantage of gas heating also plays
geneity or grain distribution is inadequate for a role, particularly with infrequent alloy
defect-free extruded bars [Ric 93]. The need for changes. The possibility of a rapid temperature
homogenization increases with increasing con- change with small batch sizes of different steels
tent of the elements molybdenum, niobium, and is an argument for induction heating.
titanium, which result in the formation of seg- Induction furnaces are more expensive to op-
regations. erate but heat more quickly, and the temperature
Because the billet surface in direct extrusion can be more accurately controlled, which is the
with lubrication without a shell and using coni- reason why induction furnaces are used in par-
cal dies becomes the surface of the extrusion, ticular for high-alloy steels with exactly speci-
the 8- to 12-m-long forged or hot-rolled round fied preheat temperatures. Complex alloy steels
bars have to be cross sectioned and carefully ma- often have only a narrow extrusion temperature
chined by turning or peeling. Coarse turning range. The upper limit is determined by the sol-
marks result in fish-bone patterns on the ex- idus temperature and the lower limit by the press
truded tube surface. A chamfer on the front face power.
of the billet simplifies the uniform flow of the The temperature of the billet core lags behind
during the rapid induction heating, which can
glass lubricant during extrusion (see below).
result in core cracking in crack-susceptible
Billet diameters from 200 to 300 mm and bil-
steels, e.g., heat-resistant ferrites with high chro-
let lengths up to 700 mm are standard.
mium contents. In this case the preheating in ro-
Whereas in the extrusion of copper alloy tubes tary hearth furnaces mentioned previously is
large billets are pierced in the press, this process recommended.
is not possible with alloy steels, which are also Although induction furnaces with the shorter
processed on hydraulic horizontal presses. The heating times of 5 to 15 minutes largely heat free
mandrels cannot withstand the severe thermo- of oxidation, a protective atmosphere is often
mechanical stresses and would rapidly wear be- passed through the induction coil with the oxide-
cause of the absence of the lubricating film. The susceptible steels. This can be necessary, in par-
billets are therefore bored, although for diame- ticular, with furnaces with a vertical axis in
ters up to 60 mm, a deep hole without expansion which the billets oxidize more severely because
is sufficient. The billet length to bore ratio of the larger air throughput from the chimney
should not exceed the value of 7:1; otherwise, effect.
the bore will deviate. With larger bore diameters, Salt bath ovens for billet heating are rarely
the predrilled billet is expanded in a separate used. Their advantage is the capability of exact
piercing press [Bil 79]. The hole diameter is al- temperature control and the avoidance of oxi-
ways larger than the mandrel diameter so that dation. They are, however, unwieldy and expen-
the lubricant spread in the bore is not stripped sive and the salt carryover presents a large en-
off by the mandrel. vironmental risk [Sar 75, Lau 76, Kur 62]. The
276 / Extrusion, Second Edition
diffusion of nitrogen damages the surface zones not break up even when being extruded
of austenite and, as a result, the extruded tubes through the die aperture. It should prevent
sometimes have to be ground over. contact with the tool working surfaces as
If the turned billet has to be pierced before well as reduce the load.
extrusion, this process is carried out in vertical ● It should form an insulating layer between
piercing presses linked to a vertical single-billet the billet and the extrusion tooling and thus
furnace in order to balance out the heat losses increase the ability of the tooling to with-
and to exactly control the extrusion temperature. stand the thermomechanical stressing. A low
In the piercing press, for example, the existing thermal conductivity is desirable.
bore diameter is expanded from 35 mm to a ● The lubricant applied to the billet surface im-
range of 53 to 74 mm, increasing the billet mediately after heating should protect this
length by up to 20%. and the emerging extrusion from oxidation
Carbon steels and low-alloy steels can oxidize with a thick film. Thin oxide coatings that
so severely that removing the thick oxide layer have already formed should as far as possible
with a strong jet of high pressure water after be removed or absorbed by the lubricant.
billet heating is recommended. This process is ● Glassy lubricants have a larger volume con-
so quick that hardly any heat is lost. traction on solidification and cooling than
The high billet temperature of high-alloy steel, and the lubricant can readily break off,
steels necessitates a fast transport from the oven particularly with rapidly cooled extrusions.
to the press. Otherwise, the material would cool
too quickly, particularly with small billet diam- Glasses that are optimally suited for all steels
eters where there is a large surface to volume with their different extrusion temperatures and
ratio. flow resistances do not exist. Therefore, glasses
The use of radiation protective sheaths has with different compositions and thus a different
been reported in the United States. These have viscosity temperature dependence are recom-
to be removed just before extrusion when the mended for the various material groups (Table
billet is loaded into the container [Lau 76]. How- 5.18).
ever, a thick glass layer, which surrounds the hot The criterion for the upper limit of the tem-
billet as a lubricant, also acts as insulation. perature application of glasses in extrusion is the
so-called “hemispherical” temperature (see foot-
5.25.4.2 Lubrication note in Table 5.18). The viscosity is then ap-
proximately 2 ⳯ 104 poise. The lower limit is
Similar to other difficult-to-extrude materials, characterized by the compressive softening tem-
e.g., the nickel alloys, the development of lubri- perature (CST) where the glass is extremely
cation technology was an important requirement tough (approximately 1010 poise) but no longer
for the economic extrusion of alloy steel tubes. breaks in a brittle manner. The extrusion tem-
The graphite and salt containing oil suspensions
perature should be at least 200 to 300⬚ above the
initially used as lubricants would carburize the
CST.
surface of low-carbon steels, among other dis-
Standardized glasses are available from vari-
advantages. Glass lubrication technology was
ous manufacturers. Today only a few types are
rapidly adopted and had to meet numerous re-
used in extrusion with SiO2 as the main constit-
quirements [Ben 73]:
uent. They contain oxides of sodium, potassium,
● The lubricant with its good slip properties calcium, magnesium, aluminum, and boron.
has to form a closed lubricant film that does Barium oxide is also sometimes added. These
Table 5.18 Glasses used successfully as lubricants for extrusion (Deg 74)
Composition Extrusion temperature
No. Na2O K2O MgO CaO BaO Al2O3 B2O3 SiO2 Maximum HK(a), ⬚C Minimum DET(b), ⬚C
1 ... ... ... Ⳮ Ⳮ Ⳮ Ⳮ Ⳮ 1300 765
2 Ⳮ Ⳮ ... Ⳮ ... Ⳮ Ⳮ Ⳮ 1220 690
3 Ⳮ Ⳮ Ⳮ Ⳮ Ⳮ Ⳮ ... Ⳮ 990 645
4 Ⳮ Ⳮ Ⳮ Ⳮ Ⳮ Ⳮ Ⳮ Ⳮ 710 510
(a) Hemispherical temperature (HK) is the temperature at which a specific quantity of the glass powder melted in a heated microscope forms a hemisphere. Viscosity
is approximately 2 ⳯ 104 poise, i.e., highly fluidic. (b) Compressive softening temperature (DET) is the temperature at which the glass has a viscosity of approximately
1010 poise and is extremely tough but no longer brittle.
Chapter 5: The Production of Extruded Semifinished Products from Metallic Materials / 277
additions lower the melting point and stabilize The stem loading is, as usual, restricted to a
the glasses. maximum of 1200 N/mm2. In order to achieve
The billet from the preheating furnace is this, there are presses with several hydraulic cyl-
rolled over a sloping table covered in the glass inders that can be individually switched off to
powder and also has powder spread in the bore avoid overloading with small billet diameters.
using a spoon. The powder immediately melts The press capacity of these presses is 35 to a
and protects the billet from further oxidation and maximum of 50 MN. Extrusion ratios (V) of 10
can even dissolve any oxide that has formed. If to 40 are standard.
the billet is not pierced before it is loaded into Because extrusion is carried out without a
the press, the procedure for applying the glass shell the dummy blocks used have to be matched
powder has to be repeated (after the reheating). as closely as possible to the container bore; a
Different glasses are sometimes used for internal cleaning pad is not required.
and external application. The grain size of the A laminar quasi-stationary material flow is
glass also plays a role because fine grain-size achieved by using dies with a conical entry inlet
powder melts more quickly than coarse grain. angle of 120 to 150⬚ or dies with a curved inlet.
In front of the die there is a pressed disc of A fast die-change system is needed to avoid
the same glass powder or fiber glass (with water overheating of the dies and to enable die re-
glass as the binding agent) that slowly melts dur- working after every extrusion. If a die has to be
ing the extrusion process and encloses the front reused, it is cooled to approximately 250 ⬚C in
of the extrusion. The thickness of the glass layer a water bath.
is of the order of 10 lm. The container is not heated during extrusion
Careful matching of the type of glass, the ex- because the heat transferred from the hot billet
trusion temperature, and the extrusion speed, as is sufficient to keep it warm. The container only
well as the quantity of glass is important to pro- has to be maintained at approximately 500 ⬚C
duce a perfect glass, coating on the extrusion. If before starting extrusion and during production
too little glass flows through the die, grooves interruptions. There are extrusion presses with
form; if the quantity is too high, the surface of rotating container devices in which two contain-
the section exhibits bulges or a so-called “orange ers are used in turn: while one container is being
peel surface” corresponding to the individual used for extrusion, the other can be cooled and
grains [Bur 70]. cleaned.
It should be mentioned that the removal of the The extrusion mandrel moves with the stem
glass film from extruded tubes is expensive and during extrusion so that no mandrel cross section
did not have to be carried out with the previous has to have prolonged contact with the hot de-
graphite-containing lubricants. formation zone in the die. The mandrel is cooled
internally as with copper materials or sprayed
5.25.5 Extrusion Process externally with water between extrusions.
A high extrusion speed is possible for the ma- In order to remove the glass lubricant from
jority of iron alloys. Depending on the material the tooling, the following operations have to be
and the extrusion ratio, ram speeds in the range carried out between extrusions:
of 20 to 300 mm/s are attained so that the billets
are extruded within a few seconds. High extru- ● The mandrel is sprayed externally with wa-
sion speeds are necessary to keep the stresses on ter.
the tooling to a minimum. The tooling tempera- ● The container is cleaned with a steel brush.
ture should not exceed 500 ⬚C. The melting ● The die is quenched in a water bath.
properties of the glass used for lubrication pre-
vents the use of the maximum extrusion speeds The discard and tube are separated with a hot
so that in practice, the minimum ram speed is 50 saw or a shear between the opened container and
mm/s and the upper limit is 200 mm/s. the die. The extruded length is restricted to a
High extrusion speeds can be achieved only maximum of 20 m for steel tube extrusion to
with hydraulic accumulator drives. In the steel ensure that the contact time between the material
industry, direct oil operating systems are not and the die is not too long. Runout tables up to
used. 50 m, which are used for aluminum and copper
The construction of the horizontal hydraulic alloys, are not possible with steel. The runout
tube extrusion presses are basically similar to trough for steel can also be fitted with powered
those used for copper tube extrusion. rollers.
278 / Extrusion, Second Edition
In the majority of cases, quenching with water Extruded and metallic clean semifinished
is carried out directly behind the die because products can be directly used as hot-finished
most of the alloys produced have to be cooled semifinished products after finishing (straight-
as quickly as possible to avoid precipitates of ening and cutting to the finished length). If nec-
carbides and intermetallic phases such as the r- essary, the surface has to be ground.
and v-phases. Precipitated phases result in em- In other cases, the extruded tubes are further
brittlement and in numerous cases, unfavorable processed by cold pilgering and/or cold draw-
corrosion behavior. Water quenching also has ing.
the advantage that the glass film breaks up so
that it can be easily removed. Quenching should 5.25.7.2 Testing
be avoided only with materials where there is a In order to prevent d-ferrite occurring in aus-
tendency for cracking with rapid cooling and tenitic steels, the billets are tested randomly by
with ferrites where martensite can form [Ric 93]. a magnetic balance. The permitted upper limit is
3%. Crack testing of the billet surface (penetrant
5.25.6 Tooling testing) is required only occasionally.
As well as the standard visual inspection of
Tooling design and other details are covered
the tube surface, ultrasonic testing is required,
in Chapter 7.
particularly with high-alloy materials and for
The shape-forming tools—die and mandrel—
some critical applications. This is carried out
are usually made in steel 1.2343 (H11, UNS
with either fixed test heads and rotating tubes or
T20811). The die with the conical entry is usu-
with static tubes and rotating test heads. Water
ally located in a die holder with a truncated
is used as the coupling agent.
shaped external face, which mates with the con-
The danger of internal cracks occurs only with
ical container seat. Container liners are also fre-
the highest-alloyed materials (molybdenum-
quently manufactured in the steel 1.2343.
containing). Internal inspection with an endo-
Dies that are removed and cooled can last be-
scope is specified only for these.
tween 20 and 40 extrusions and can then be
opened up to another dimension. The mandrel
life is around 400 extrusions and that of the con- 5.26 Steel Sections
tainer about 4000 extrusions, with the possibility
of reworking. 5.26.1 General
The use of high-alloy materials for dies and
liners in the extrusion of alloy steels has been 5.26.1.1 Extrusion Process, Materials
tried but for economic reasons is not used As with alloy steel tubes, only horizontal hy-
[Ben 73]. draulic extrusion presses are used for steel sec-
tions. The laminar extrusion takes place with
5.25.7 Further Processing, Testing glass lubrication and without a shell. In this case
the competing processes, which are economi-
5.25.7.1 Further Processing cally more competitive for suitable quantities
and specific sections, again have a higher market
Steel, ball shot blasting (VacuBlast) is used, share than the extrusion process.
followed by pickling in nitric acid with hydro- In principle, all steel grades that can be hot
fluoric acid additions to remove residual glass worked can be extruded to sections. Neverthe-
lubricant from the internal and external surfaces less, the tool wear increases drastically with in-
of the tube. Hot molten sodium and calcium salts creasing extrusion temperature. The higher the
are used to some extent for surface cleaning, but flow stress at the extrusion temperature, the
they are expensive and environmentally un- lower the possible extrusion ratio will be and
friendly because salt carryover is difficult too also, as a rule, the length of the extrusion.
avoid.
Heat treatment after extrusion is necessary if 5.26.1.2 Competition with Other
it is not possible to arrange the cooling of the Deformation Processes
hot extrusion so that a precipitation-free struc-
ture is obtained. The heat treatment after extru- The processes used to produce sections are:
sion then has the nature of a homogenization or ● Hot rolling: The dimensional range falls
a solution heat treatment. within a circumscribing circle of 250 mm di-
Chapter 5: The Production of Extruded Semifinished Products from Metallic Materials / 279
production for homogenizing and to achieve a the container has been opened, the discard is cut
fine-grain, crack-free structure. from the section with a hot saw. The section is
The extrusion process with a lubricated con- pulled back through the die and then removed
tainer and without a shell resembles that de- on a powered roller conveyor. After pushing out
scribed for tube production. The large billets the discard together with the dummy block, the
used for heavy sections and, in the case of hol- die is changed for a new or reworked die using
low sections, prebored billets also have to be a rotating arm or a slide. The die has to be
chamfered on the end surfaces to achieve the checked for the dimensional tolerances after
uniform flow of the glass lubricant. each extrusion and, if necessary, reworked be-
cause of the high thermomechanical stresses.
5.26.3 Billet Production, The length of the section that is extruded as
Extrusion, Further Processing quickly as possible has a maximum length of 20
m so that the die that is deformed by the tem-
5.26.3.1 Billet Preparation, perature effect during the extrusion does not ex-
ceed the extrusion tolerances toward the end of
Heating, Lubrication
the extrusion.
As soon as an order is passed to production, The required high ram speeds of up to 300
the bars delivered to billet production are cross- mm/s can only be achieved by a water hydraulic
cut, peeled, turned or ground and chamfered. system.
The billets for hollow sections have also to be The sections cool in free air but bend and
bored. The hole is larger than the circumscribing twist significantly in the longitudinal direction
circle of the mandrel cross section. The billets and deform in the transverse direction because
are heated to 1000 to 1300 ⬚C in a rotary hearth of the different flow behaviors of different cross-
furnace with a reducing protective gas burner or sectional areas in the die and the faster cooling
in an induction furnace similar to steel tubes. of thin legs after extrusion. To avoid accidents
Salt bath heating is also used. from moving sections, the runout table is occa-
After the billets have been removed from the sionally covered to form a tunnel.
furnace, they are rolled down a table with glass In multihole extrusion, the extruded sections
powder. The glass film formed from the molten usually have varying lengths because of the dif-
powder prevents high thermal losses and oxi- ferent amounts of lubricant in the die openings.
dation of the billet surface and can even dissolve
the oxide that has formed. A 4 mm-thick glass
powder disc bonded with water glass is placed 5.26.3.2 Further Processing
in front of the conical die. The type of glass used The extruded sections have to be straightened
is the same as for the extrusion of steel tubes and detwisted by stretching 2 to 3% on stretchers
(e.g., type 3 in Table 5.18 for carbon steels). with rotating stretcher heads and capacities of
Extrusion. The tube and solid extrusion up to 3000 kN. Hot stretching is also used for
presses used have a capacity of 15 to 25 MN. the higher-strength alloys (alloy steels, Ni, and
The diameter of the billets varies from 150 to Ti alloys). This stretching process is sufficient
250 mm, depending on the section cross-sec- with carbon steels to break off the 10 to 20 lm-
tional area, and the length can extend to 900 thick glass film from the lubrication. Alloy
mm. Extrusion ratios up to 100 are possible but steels, however, have to be pickled and some-
rarely used. times first shot blasted.
Hollow sections are extruded over round or After stretching, it may be necessary to carry
profiled mandrels that are not internally cooled out further straightening on a roller correction
and that move with the stem during the extrusion machine or even on a straightening press with
process. The thickness should be at least 20 mm profiled tools. This straightening process adds
to be able to withstand the large thermal stresses. significantly to the costs of producing steel ex-
It is not possible to use bridge dies as with alu- truded sections [Lin 82].
minum and copper because of the high extrusion If a coarse grain structure or, in the case of
temperature, the relatively high flow stress, and alloy steels, excessive mechanical properties are
the resultant thermomechanical stresses on the detected, a subsequent annealing treatment is re-
tooling. quired.
The billet loaded into the container is ex- Tight tolerances are obtained by bright draw-
truded to a discard length of 10 to 20 mm. After ing. If necessary, sections can also be ground.
Chapter 5: The Production of Extruded Semifinished Products from Metallic Materials / 281
Table 5.19 German Standardization Institute (DIN) standards for nickel alloys
Similar
Comments ASTM
Standard Designation to DIN standard Title
DIN 17740 Nickel in semifinished Composition B39 Standard Specification for Nickel
products
DIN 17741 Low-alloyed nickel Composition ... ...
wrought alloys
DIN 17742 Nickel wrought alloys Composition B167 Standard Specification for Nickel Chromium-Iron
with chromium Alloys (UNS N06600, N06690, N06025)
Seamless Pipe and Tube
DIN 17743 Nickel wrought alloys Composition B164 Standard Specification for Nickel-Copper Alloy
with copper Rod, Bar, and Wire
DIN 17744 Nickel wrought alloys Composition B335 Standard Specification for Nickel Molybdenum-
with molybdenum and Alloy Rod
chromium
DIN 17745 Wrought alloys of nickel Composition B407 Standard Specification for Nickel-Iron-Chromium
and iron Alloy Seamless Pipe and Tube
B408 Standard Specification for Nickel-Iron-Chromium
Alloy Rod and Bar
DIN 17751 Tubes in nickel and Dimensions, B161 Standard Specification for Nickel Seamless Pipe
nickel wrought alloys mechanical and Tube
properties
DIN 17752 Bar in nickel and nickel Dimensions, B160 Standard Specification for Nickel Rod and Bar
wrought alloys mechanical
properties
DIN 17753 Wire in nickel and nickel Dimensions, B473 Standard Specification for UNS N08020, UNS
wrought alloys mechanical N08024, and UNS N08026 Nickel Alloy Bar
properties and Wire
B475 Standard Specification for UNS N08020, UNS
N08024, and UNS N08026 Nickel Round
Weaving Wire
plants, steam generators, and resistance heating Nickel alloys can be continuously cast. If the
elements. charge size is insufficient for continuous casting,
The superalloys contain cobalt, molybdenum, chill mold casting with all its disadvantages
iron, titanium, and aluminum, in addition to (coarse, radial columnar, and frequently crack-
chromium and nickel. A wide range of appli- susceptible structure) is preferred. For this rea-
cations are possible at high and very high tem- son, as well as reducing the large chill mold cast-
peratures. These include gas turbines, jet en- ing to the billet dimensions, they are usually
gines, and nuclear power stations. Hot-working broken down by forging or rolling. This aligns
tooling is also produced from these alloys. the grains axially and frequently produces a fine-
There are high-strength dispersion-hardened grained recrystallized structure. It is then nec-
nickel alloys that have to be produced by powder essary with the high-alloy materials to follow
metallurgy. These alloys are discussed in the this with a homogenization heat treatment to
section “Extrusion of Powder Metals.” minimize the segregation.
The feedstock material supplied to the press
as long bars is sawn to length, turned, and cham-
fered. If tubes are being produced, the billets
5.29 Billet Production
usually have to be bored. A good billet surface
is necessary as is the case with alloy steels be-
Depending on the composition and the ma-
cause it will form the surface of the extrusion as
terial requirements, various routes are used to
a result of the glass lubrication (see below) and
produce the starting material and these have
the resultant laminar material flow.
been described in section 5.41.5 [Ric 93].
High-alloy materials are melted in an electric
arc furnace and, if a specific purity is required,
subjected to the Vacuum-oxygen-decarburiza- 5.30 Billet Heating
tion (VOD) process in an evacuated ladle. This
removes the carbon and nitrogen and reduces the The billets have to be heated in a low-sulfur
sulfur content drastically. furnace atmosphere because of the sensitivity of
Chapter 5: The Production of Extruded Semifinished Products from Metallic Materials / 283
nickel and its alloys to intercrystalline attack by oil for low extrusion ratios and thus low extru-
sulfur. It should be weakly reducing in gas-fired sion temperatures, higher-alloyed material bil-
furnaces because nickel and nickel-copper al- lets are only lubricated with glass using the Sé-
loys in particular tend to intercrystalline corro- journet process similar to alloy steels [Pol 75].
sion and thus embrittlement in an oxidizing at- Suitable glasses for the corresponding tempera-
mosphere even without sulfur [Vol 70]. ture are selected from Table 5.18. The glass with
Because the oxide layer of severely oxidizing the highest melting point is used for the high-
nickel-iron and nickel-copper alloys also re- alloy materials with extrusion temperatures of
duces the effect of the lubricant in extrusion and almost 1300 ⬚C. The glass powder is applied
produces a poor surface quality, these materials even with two-stage heating (gas furnace-induc-
should be heated as quickly as possible—at best, tion furnace) only after the billet has left the in-
in an induction furnace. duction furnace.
With high-alloy, crack-sensitive alloys on the
other hand, and with coarse grain cast billets, a
slow heating rate is important because if the 5.31.2 Deformation Behavior
heating is too rapid the thermal stresses can re- and Extrusion Data
sult in grain-boundary cracking. Some nickel- Figure 5.65 shows the tensile strengths of
chromium-cobalt alloys cannot be directly various nickel alloys as a function of tempera-
charged into the hot-gas-fired furnace if they ex- ture.
hibit coarse grain or severe segregation but have The flow stress of pure nickel is low enough
to be slowly heated from a low temperature to for extrusion even below 1000 ⬚C. Similarly, the
the extrusion temperature so that the temperature soft alloys of nickel with copper or with up to
gradient remains low in all phases of heating 20% Cr have a relatively wide temperature range
[Pol 75]. Reducing continuous, chamber or ro- for hot working. The complex alloys on the
tary furnaces are used for this. other hand have narrow deformation tempera-
High-alloy materials that are not crack sensi- ture ranges, in particular, the molybdenum-con-
tive and those that have been well homogenized taining and the high-strength nickel-chromium
and have a fine-grain structure can, however, be alloys, and these must be accurately maintained
heated in an induction furnace that guarantees to avoid cracking.
the exact final temperature. With complex al- The addition of strength-increasing elements
loys, the exact setting of the final temperature is to improve the mechanical properties at high
very important if a low-melting-point eutectic
has formed (e.g., with niobium).
To save energy and to ensure the slow heating
of crack-sensitive materials mentioned above, a
gas furnace can be used for the base heating (up
to 1000 ⬚C) and an induction furnace for the final
stage [Ric 93]. Salt bath heating cannot be used
because of the risk of the diffusion of embrittling
elements.
5.31 Extrusion
Table 5.20 Some important typical nickel alloys that are extruded
(a) Nickel and low-alloyed nickel materials
Semifinished
Material Standard British/U.S. Ni Fe Mn Al Other product Strength Properties Application
Ni 99.2 DIN 17740 NA 11 ⬎99.2 ⬍0.4 ⬍0.35 ... ... R, S, D 370–590 High electrical and Corrosion-resistant components,
2.4066 Alloy 200 thermal conductivity, lightbulbs, electrode tubes
corrosion resistant
NiMn2 DIN 17741 ... ⬎97.0 ... 1.5–2.5 ... ... S, D ... ... Lightbulbs, electrotubes, spark
2.4110 plugs
(b) Nickel-copper alloys (Monel)
Semifinished
Standard British/U.S. Ni Cu Fe Al Other product Strength Properties Application
NiCu30Fe DIN 17743 NA 13 ⬎63 28–34 1.5–2.5 ... ⬍2.0 Mn R, S, D 450–700 Good strength, best high- Corrosion resistant construction
2.4360 Alloy 400 corrosion resistance units, ship construction,
chemical industry
NiCu30Al DIN 17743 Na 18 ⬎63 27–34 0.5–2.0 2.2–3.5 0.3–1.0 Ti R, S, D 600–800 Age hardening Chemical industry, petrochemical
2.4375 Alloy K500 industry
(c) Nickel iron alloys
Semifinished
Material Standard British/U.S. Ni Fe Other product Strength Properties Application
Ni 42 DIN 17745 Alloy 42 40.0–43.0 Remainder ... R, D ... Low temperature expansion Glass/metal ceramic bonds, e.g., for
1.3917 integrated circuits
Ni 48 DIN 17745 Alloy 48 46.0–49.0 Remainder ... R, S, D ... Best coefficient of expansion, Relay components, transformers
1.3922/26/27 slightly magnetic
(d) Nickel-chromium (iron) alloys
Semifinished
Material Standard British/U.S. Ni Cr Fe Ti Other product Strength Properties Application
NiCr20Ti DIN 17742 Alloy 75 ⬎72 18–21 ⬍5 0.2–0.5 ... S, P, R, D 650 High oxide and corrosion resistance Furnace components, heating conductor,
2.4951 gas turbines
NiCr15Fe DIN 17742 NA 14 ⬎72 14–17 6–10 ... ... S, R, D 550 Heat resistant, corrosion resistant Furnaces, chemical industry, spark plugs
2.4816 Alloy 600
NiCr20TiAl DIN 17742 Alloy 80A ⬎65 18–21 ... 2.3 1.0–1.5Al S, P, R, D 1100 Age hardening, high hot strength Components subjected to creep loading
2.4952 1.9Ti
(e) Nickel alloys with chromium, molybdenum, and/or cobalt super alloys
Semifinished
Material Standard British/U.S. Ni Cr Fe Co Mo Other product Strength Properties Application
NiMo16Cr16Ti Din 17744 Alloy C4 Remainder 14–18 ⬍3 ⬍2 14–17 ... S, R, D 690–850 Excellent corrosion Chemical industry, paper
2.4610 properties industry
NiMo16Cr15W DIN 17744 Alloy C276 Remainder 14.5–16.5 4.0–7.0 ⬍2 15–17 3.0–4.5W S, R, D 690–850 Excellent corrosion Chemical industry, paper
2.4819 properties industry
NiCr22Mo9Nb DIN 17744 Alloy 625 Remainder 20–23 ... ... 8–10 3.15–4.15Nb S, R, D 690–830 High strength without Chemical industry,
2.4856 age hardening, aircraft
corrosion resistant
NiCr23Co12Mo DIN 17744 Alloy 617 Remainder 20–23 ... 10–15 8–10 Al, Ti S, R, D ⬃700 Stable up to high Gas turbine,
2.4663 temperature, resistant petrochemical
to oxidation industry, chemical
industry
NiCr20Co18Ti 2.4632 NA19 58 20 ⬍1.5 18 ... 2.5 Ti1.5Al S, P, R ⬃1100 Creep resistant up to 900 Gas turbine, hot-working
Alloy 90 ⬚C tools
NiCr15Co14MoTiAl 2.4636 Alloy 115 51 15 ... 14 4 4Ti5Al S, P ⬃1200 Creep resistant up to Jet engine
1010 ⬚C
Chapter 5: The Production of Extruded Semifinished Products from Metallic Materials / 285
286 / Extrusion, Second Edition
temperatures results, on one hand, in a reduction mains between the two limits. In other words, if
in the liquidus temperature and, on the other the plant is capable, “isothermal extrusion” is
hand, an increase in the flow stress. required. Extrusion presses built especially for
These difficult-to-extrude alloys require a nickel have a suitable speed control system. Oil
high degree of homogeneity in the starting ma- hydraulic presses are preferred to water hydrau-
terial (see section 5.29), uniform billet heating lic ones [Lau 76]. A high press power (up to 60
(see section 5.30), correct lubrication condi- MN) simplifies the extrusion of the high-alloy
tions, and exact maintenance of the extrusion nickel materials with high flow stresses [Eng
conditions. Economic production is, therefore, 74]. Because the billet rapidly cools at this slow
not possible without an extrusion plant with a speed with the risk of freezing, only short billets
correspondingly high extrusion power [Inc 86]. can be used.
Table 5.21 gives data for the extrusion of Ultrasonic testing of extruded products is rec-
some nickel alloys. ommended for the crack-sensitive materials.
In the high-strength nickel alloys, there are
some with a low-melting-point eutectic (e.g.,
with niobium) that can only be extruded with a
maximum of 1150 ⬚C and thus with a low ex-
5.32 Tooling, Further Processing
trusion ratio (e.g., Inconel 625).
Some superalloys, for example, the high- Information on the tooling used and the tool-
molybdenum-containing alloys, have to be ex- ing design is given in Chapter 7.
truded above 1400 ⬚C to obtain low flow The dies are, as described for alloy steel tubes,
stresses. Preferably, extrusion is carried out be- conical to obtain a laminar flow with the glass
low 1300 ⬚C because of the high tool wear and lubrication.
the low viscosity of the glasses used, and the The further processing is also similar to that
resultant low extrusion ratio is accepted. This described for alloy steel. The glass lubricant film
naturally means more expensive further pro- is removed by shot blasting with steel grit fol-
cessing. lowed by pickling. If the glass skin is broken up
by quenching at the press (to suppress precipi-
5.31.3 Defects and Their Prevention tation), shot blasting and pickling may not be
required. Cold pilgering or drawing is then car-
Narrow limits are placed on the extrusion ried out, possibly with intermediate annealing.
speed, particularly for the complex molybde-
num-containing nickel alloys. If the extrusion
speed is too slow, the lubricant film breaks up,
resulting in a rough surface on the extruded
product and/or the extrusion process “freezes.”
If the extrusion speed is too high, the exit tem- Extrusion of Semifinished
perature can increase to such an extent that
transverse hot cracking occurs or—particularly Products in Exotic Alloys
with thick bars—lap defects occur. Conse-
quently, especially for the slowly extruded com- Martin Bauser*
plex high-alloy steels with extrusion speeds be-
low 10 mm/s, the extrusion speed has to be All the materials described in this section are
controlled to ensure that the exit temperature re- rarely used in long lengths and are therefore not
Table 5.21 Data for the extrusion of some nickel alloys (see Table 5.20 for examples indicated by
(b), (c), (d), and (e) (Lau 7, Vol 70, Ric 93)
Group Characterization Approximate Kf value, N/mm2 Billet preheat temperature Examples
1 Easily extruded 150 900–1100 ⬚C All nickel and the low-alloyed nickel materials
2 Good extrudability 200 1050–1150 ⬚C Monel(b)
Nickel iron(c)
3 Difficult to extrude 250 1100–1250 ⬚C Ni-Cr materials(d)
4 Very difficult to extrude 320 1150–1280 ⬚C Ni-Cr-Mo materials
Super alloys(e)
5.33 Beryllium
carried out between 650 and 790 ⬚C because of be melted in vacuum induction melting furnaces
the risk of cracking. or in vacuum arc furnaces. Because the structure
is similar, the extrusion is the same as for pure
5.34.2 Deformation Behavior, Extrusion uranium [Eck 90]. Because the b/c phase bound-
ary is displaced to lower temperatures by these
The billets are melted in induction furnaces alloying additions and because in the c-region
under a vacuum and cast in molds. secondary phases are held in solution, the extru-
The deformation behavior of uranium is sion of alloys is easier.
shown in Fig. 5.67. The extrusion in the lower
␣-region (between 550 and 650 ⬚C) avoids the
difficulties of high-temperature extrusion de- 5.35 Molybdenum, Tungsten
scribed subsequently but does require a high
press power because of the higher flow stress. 5.35.1 Molybdenum
The extruded sections are fine-grain recrystalli-
zed. It is possible to work in this temperature Molybdenum is usually used as an alloying
range without cladding with the usual graphite- element in steels and high-alloyed materials.
grease lubrication. Preheating the billets in a salt However, it is also important as a pure metal and
bath prevents oxidation. They should, however, a low-alloy material. Tools in TZM (Mo-0.5 Ti-
be subjected to the atmosphere for only a short 0.17Zr), for example, can withstand tempera-
time at the extrusion temperature. tures well over 1000 ⬚C. Further application ar-
In the c-region (between 800 and 1000 ⬚C), eas are cathodes, electric resistance elements (up
where significantly higher extrusion ratios can to 2200 ⬚C), and high-temperature components
be used, uranium reacts very rapidly with iron, in space travel and for rockets. The highest ap-
nickel, and other metals and is very susceptible plication temperature is 1650 ⬚C. Molybde-
to oxidation. The billets for this hot extrusion num’s good resistance to hydrochloric acid is of
are usually clad in copper, evacuated, and then interest to the chemical industry. The density of
extruded using graphite grease as a lubricant. molybdenum is 10.2 g/cm3 [Joh 90].
Only a few low-alloy-content uranium alloys The high melting point of 2622 ⬚C permits
with higher mechanical properties and better only powder metallurgical processing. The pow-
corrosion resistance are known (with titanium, der is obtained by hydrogen reduction of mo-
zirconium, molybdenum, and niobium) that can lybdenum oxide and then cold compacted and
sintered. These sintered billets can then be either
directly extruded or melted in a vacuum arc fur-
nace.
The bcc lattice of molybdenum is the reason
behind the excellent deformation characteristics.
This can be deduced from the hot tensile
strength curves in Fig. 5.68.
Pure molybdenum is extruded in the range
1065 to 1090 ⬚C and the most common alloy
TZM (Mo-0.5Ti-0.1Zr) at 1120 to 1150 ⬚C. The
billets are heated in conventional gas or oil-fired
furnaces or by induction. Above 650 ⬚C, molyb-
denum oxidizes as a gas with a weight loss of 1
to 5% without an oxide layer forming. Rapid
heating obviously reduces the loss from oxida-
tion. Similar to steel, glass has to be used for
extrusion. Bar, tube, and simple shapes can be
produced by extrusion [Joh 90]. The glass ap-
plied as powder after the billet has left the fur-
nace melts and protects it from oxidation.
5.35.2 Tungsten
Fig. 5.67 Hot tensile strength and elongation of uranium as Tungsten melts at the extremely high tem-
a function of the temperature [Eck 90] perature of 3380 ⬚C. The structure and properties
Chapter 5: The Production of Extruded Semifinished Products from Metallic Materials / 289
5.36.1 Tantalum
Fig. 5.68 Hot tensile strength of some high-melting-point Tantalum has similar structure and properties
metals and alloys as a function of temperature
[Kie 71] to niobium. It also has a bcc structure but first
melts at 3030 ⬚C and is twice as heavy with 16.6
g/cm3.
are similar to molybdenum. With its high density The widest application of tantalum—apart
of 19.3 g/cm3, it dominates where high weight from an alloying element in steel like niobium—
is a main requirement. The high melting point is as an anode material in electrolytic cells. In
combined with its high electrical resistance the chemical industry it is known for its resis-
makes it the most common material for heating tance to nitric acid, hydrochloric acid, and sul-
conductors and filaments in lamps [Joh 90a]. furic acid. The high melting point ensures ap-
In contrast to molybdenum, a significantly plications in the high temperature region
higher hot-working temperature of 1500 to 1800 [Pok 90].
⬚C is required, as shown in Fig. 5.68, which Processing usually follows a powder metal-
makes tungsten unsuitable for extrusion. Hot lurgical route. Electron beam cast tantalum is
forging of sintered powder billets is preferred usually too coarse grained for further processing
[Par 91]. and has to be forged before it can be extruded.
The extrusion of compacted and sintered
powders has been mentioned but does not have
any great importance because the recrystalliza-
5.36 Niobium and Tantalum tion temperature, and thus the extrusion tem-
perature, is very high [Pok 90].
Niobium melts at 2468 ⬚C and at room tem-
perature has a bcc structure with a density of 8.4
g/cm3. It can be readily worked at room tem-
perature. Niobium alloys have a wide range of
applications in space travel because of their rela-
tively low weight and high hot strength. Nio- Extrusion of
bium and its alloys are also in demand in the Powder Metals
chemical industry because of the resistance to
specific corrosive media [Ger 90].
Similar to other high-melting-point metals, Martin Bauser*
the extrusion billets are made by a powder met-
allurgical route.
Figure 5.68 shows for niobium a relatively
5.37 General
low hot-working temperature. Extrusion tem-
peratures between 1050 and 1200 ⬚C with extru- Oxide-containing aluminum powder was ex-
sion ratios of V ⳱ 4 to V ⳱ 10 have been de- truded in the 1940s under the name sintered alu-
scribed for niobium alloys with zirconium,
hafnium, and tungsten [Ger 90]. However, nio- *Extrusion of Powder Metals, Martin Bauser
290 / Extrusion, Second Edition
minum powder (SAP). In the 1950s the advan- tallic particles as dispersions by extrusion is also
tages of the extrusion of powder was known for discussed in this chapter (metal matrix compos-
reactor materials and beryllium. This process ites, or MMCs). Chapter 4 discusses the physical
has only recently found a wide application, par- properties, in particular those at high tempera-
ticularly with aluminum alloys but also high- tures, and the processes in the deformation of
alloyed and dispersion-hardened materials. dispersion-hardened materials. Frequently, me-
A good overview of powder metallurgy (P/ tallic or nonmetallic fibers are mixed with the
M) can be obtained from the textbook on powder metal powder to achieve certain properties and
metallurgy by W. Schatt [Sch 86]. The work of then extruded [Boe 89]. The resultant so-called
Roberts and Ferguson gives detailed information fiber composite materials are described in the
on the extrusion of powder metals [Rob 91]. section “Extrusion of Semifinished Products
from Metallic Composite Materials.”
5.37.1 Main Application Areas
of Powder Metallurgy 5.37.3 Powder Production
Processing by extrusion plays an important Atomization of the melt using water or gas
role compared with other processes in P/M. The streams is the most common of all the different
most important is the processing of metal pow- casting, mechanical, and chemical processes
ders to near final shape and thus the economic used to produce metal powders. Water gives the
production of molded components with a piece fastest cooling rate, but the powder particles are
weight below 2 kg, and mainly in iron alloys. coarser (approximately 500 lm) and in a spat-
The powder is compacted on vertical compac- tered format. If, however, atomization is carried
tion presses in dies by a stem and then sintered out in an air or protective gas jet, more rounded
at a high temperature, during which the particles shapes and smaller particles are produced (down
form a solid bond. For large pieces with simple to a few lm, depending on the process param-
geometries (e.g., forging billets), the compaction eters) (Fig. 5.69). The output per hour of atom-
is carried out by fluid pressure applied on all ization plants is relatively low. Because a re-
sides (cold isostatic pressing, or CIP) before stricted particle size is usually required and the
they are sintered. Compaction and sintering car- powder usually falls in a wide particle spectrum,
ried out in a single operation by hot isostatic the particles of different sizes have to be sepa-
pressing (HIP) is also used occasionally. rated by sieves. The powder costs are corre-
spondingly high. A desired material composi-
5.37.2 Advantages of Metal tion can be obtained by mixing powders if it
Powder Extrusion does not exist in the atomized melt.
“Reaction milling” in ball mills is a new pro-
Where long semifinished products can be con- cess that enables the mechanical alloying of
ventionally produced by casting and extrusion, metal components. Nonmetallic particles can
powder extrusion is usually less favorable be- also be finely dispersed by this method. The
cause the production of suitably mixed and powder particles are repeatedly broken down
sieved powders is usually too expensive. and welded between steel balls. A fine structure
The production of extruded semifinished is obtained after a certain milling time [Inc 86].
products by the powder route is worthwhile
when:
5.37.4 Spray Compaction
● The material cannot be processed conven-
In the new process of spray compaction de-
tionally by melting and casting.
veloped by the company Osprey [Cra 88], the
● An extremely fine grain size and finely dis-
gas-atomized material from the melt is sprayed
tributed precipitates have to be achieved.
onto a rotating block with a vertical axis ([Man
Rapidly quenched powder can have a signifi-
88] (Fig. 5.70). The slowly sinking block grows
cantly extended solid-solution range
layer by layer. This process saves precompac-
[Tus 82].
tion, encapsulation, and evacuation.
● A uniform distribution of very small inclu-
Hard particles can be blown into the spray by
sions to achieve specific properties is re-
an injector and form a dispersion in the finished
quired (dispersion hardening).
billet.
This last-mentioned processing of metal pow- The disadvantage of spray compaction is that
ders with mixed or reaction produced nonme- a considerable part of the spray droplets miss the
Chapter 5: The Production of Extruded Semifinished Products from Metallic Materials / 291
Fig. 5.69 Example of a gas atomization plant for metal powder [Wei 86]
5.38.1 General
The individual powder particles are plasti-
cally deformed in the extrusion direction during
the extrusion of metal powders, usually at the
same temperature as cast billets, and the surface
area increases. Oxides and other films on the
Fig. 5.70 Schematic of spray compaction [Arn 92] particle surface break up and release new reac-
292 / Extrusion, Second Edition
The reasons for encapsulation include: made for an equalization time before loading the
billet into the furnace (possibly in an equaliza-
● Excluding a reactive powder material from tion furnace).
air and extrusion lubricants Encapsulated powders (version c) are usually
● Protection from poisonous materials during extruded with lubricated containers and conical
handling (e.g., Be and U) dies (90–120⬚) or indirectly. This gives a laminar
● Risk of breaking up of green compacts of material flow and a uniform cladding material
round powders or other particles that are dif- thickness on the extrusion. The selection of the
ficult to compact in a billet shape lubricant depends on the cladding material (e.g.,
● Improved lubrication and friction behavior aluminum: unlubricated; copper: graphite-oil;
and better flow through the die by the correct iron: glass). Nevertheless, a uniform laminar
selection of the container material material flow can be achieved only with round
● Keeping the base material away from the die bar or tubes and simple section shapes. Section
and the zone of severe shear deformation. extrusion is successful only when a suitable die
This is important only for materials with low inlet has been developed.
ductility [Rob 91]. A billet produced from powder usually has a
With high-purity materials, processing has to lower density than a cast billet. A longer billet
be carried out in a clean room with careful clean- is therefore needed for the same section weight.
ing of the can and evacuation at an elevated tem- In extrusion the stem initially pushes together
perature. the still not highly compacted powder in the con-
A large disadvantage of this process is that tainer before the particles are subjected to a
the can material remains on the surface of the shear deformation and friction between each
extruded product and can be difficult to remove other in the entry (shear) zone to the die and in
by machining or by pickling. There has been the die itself. The bonding of the grains on the
reference to a degassed and hot-compacted alu- newly formed surface occurs by friction (or
minum powder in an aluminum capsule, which pressure) welding under high pressure and takes
is removed from the billet before extrusion by place more quickly than the more conventional
machining [Sha 87]. sintering process used in powder metallurgy.
The extrusion process can produce a better
bond between individual particles than sintering.
This applies in particular to aluminum alloys,
5.39 Mechanism and the powder particles of which always exhibit
Flow Behavior in the surface films of aluminum oxide because of the
Extrusion of Metal Powders high reactivity of the element aluminum. These
films are broken up to such an extent in extru-
If loose powder is extruded (version a), the sion that the higher the extrusion ratio the
container first has to be sealed on the die side to greater the number of newly formed surfaces
ensure good compaction by the stem. The die is available for particle bonding. An extrusion ratio
then opened. of at least 20 is often stated to be certain of
With precompacted green blanks (version b), achieving a perfect bond between the powder
a “nose” or a disc of the cast material corre- particles [Sha 87a]. The resultant structure of the
sponding to the powder is often placed in front extruded powder corresponds to the structure
of the die. This compensates for the risk of the formed during the extrusion of solid billets.
surface of the extrusion tearing due to insuffi- Encapsulated powder has to be well com-
cient initial pressure. Indirect extrusion is pre- pacted and degassed. If the strength of the pow-
ferred because of the more uniform material der material and the encapsulating material dif-
flow. Extrusion with a lubricated container is fer too severely, or if the can is too thin and the
avoided because of the risk of lubricant penetra- powder inadequately compacted, there is the risk
tion of the green blank. of folds forming during extrusion (Fig. 5.73).
The thermal conductivity in the green blank Diffusion between the can material and the pow-
is relatively low. Too-rapid billet heating there- der material should be prevented as far as pos-
fore results in localized melting with the risk of sible, and it should not be possible for a eutectic
cracking. Slow heating in a chamber furnace is to form between them. When selecting the can
the most suitable. If heating has to be carried out material, consideration should always be given
in an induction furnace, allowance has to be to the fact that it later has to be removed.
294 / Extrusion, Second Edition
small dimensions, in a cylindrical compression because the dispersed particles are finer and bet-
die to a green blank with 75 to 80% of the theo- ter distributed.
retical density. In the extrusion press the green Milling aluminum powder with electrogra-
blank is almost 100% compressed with an ini- phite followed by heat treatment for complete
tially closed die and then extruded using the di- transformation of the carbon into Al4C3 pro-
rect or the indirect process at 450 to 500 ⬚C [Sha duces a dispersion-hardened aluminum material
87]. Placing a “nose” or a disc of aluminum in with embedded Al4C3 and Al2O3 particles mar-
front of the powder billet can promote sufficient keted under the trade name Dispal [Arn 85]. In
compaction during upsetting and also prevent variations of the material solid-solution hard-
the start of the extrusion from breaking up. The ening AlMg5 or AlSi12 is used as the base ma-
abrasive effect of hard particles in a powder mix- terial instead of pure aluminum to achieve better
ture on the shape-forming tools is also reduced. mechanical properties even at lower tempera-
Encapsulation with degassing at 500 ⬚C and hot tures. Whereas the solid-solution hardening and
compaction is required only if absolute freedom precipitation hardening are lost at higher tem-
from hydrogen is specified. The cladding can be peratures, the dispersion hardening is retained.
removed by machining prior to extrusion. Dispal materials with high silicon content are
In practice, the extrusion of aluminum powder preferably processed by spray compaction to ex-
materials is worthwhile only if it produces a ma- trusion billets. As well as saving the cost of cold
terial that cannot be produced by casting tech- isostatic pressing of powders, the main advan-
nology. Most attention is paid to the high-alloy tage is the fine distribution of the embedded par-
materials with high room temperature strength ticles. After extrusion, rapidly solidified alumi-
as well as dispersion-hardened materials that num powder with iron and nickel additions
have a much higher strength and better mechan- contain finely distributed particles of interme-
ical properties at higher temperatures than nat- tallic phases of the types Al3Fe and Al3Ni (me-
urally hard and precipitation-hardened alumin- tallic dispersoids) [Sha 87]. Alloys based on
ium alloys (Fig. 5.75). AlFeCe, AlFeMo, AlCrMnZr, and AlNiFeMn
In the 1940s, a process was developed for pro- with additions of copper, magnesium, and tita-
ducing and working an oxide-containing powder nium, which also form intermetallic dispersoids,
from aluminum powder by a milling process. are used to achieve high hot strengths. This re-
This product was referred to as sintered alumi- sults in alloys that have an approximately 100%
num powder (SAP) [Irm 52, Jan 75]. Originally, higher hot strength in the temperature range 250
the extruded aluminum material contained 12 to to 350 ⬚C, compared with conventional materi-
15% Al2O3; today less than 5% Al2O3 is used als. The fatigue strength of such materials can
also be significantly improved. The E-modulus
is also increased by 20 to 30%. These improve-
ments in the mechanical properties are, however,
obtained with an increase in density to 2.8 to 3.0
g/cm3 because of the increased content of heavy
elements [Sha 87a]. In powder metallurgically
produced aluminum alloys with silicon contents
of 10 to 30%, the eutectic and the primary
phases are very finely formed in the structure
(⬍25 lm). This structure has an advantageous
effect on the hot and fatigue strengths [Sha 87a].
The alloys can be readily mechanically worked
and are characterized by a low coefficient of
thermal expansion. For bearing elements, the ex-
trusion of powder- and spray-compacted mate-
rials produces an uneven finer distribution of
hard particles than that achieved by casting. The
wear properties are significantly improved. Ma-
terials that contain other elements in addition to
Fig. 5.75 Temperature dependence of the tensile strength of silicon are being tested in engine construction
different aluminum alloys. 1, aluminum 99% soft;
2, AlZnMgCu1.5; 3, sintered aluminum powder (SAP) with 10% [Arn 92a], where, however, the high manufac-
Al2O3; 4, Al with 4% C (as Al4C3) [Sch 86] turing cost is a major barrier in spite of the sig-
296 / Extrusion, Second Edition
nificantly better properties compared with con- cipitates. However, with spray compaction, the
ventionally produced components. A particles are so finely distributed that the billets
breakthrough is high-silicon-containing alumi- can be readily extruded without difficulty to rod
num tubes for cylinder sleeves that have recently and tube. Graphite particles, which improve the
been extruded from spray-compacted billets slip properties, can be included by an injector
[Hum 97]. during the spray compaction (see Fig. 5.70). A
Other aluminum alloys produced by mechan- further application of spray-compacted-pro-
ical alloying with oxides and carbides as disper- duced tubes of high-alloy bronze is as super con-
soids and that contain 1 to 4% copper and mag- ductors [Mur 96].
nesium are commercially available. They are hot Dispersion-hardened silver materials (e.g.,
compacted and then extruded. However, only with AgNi2 or with cadmium oxide) have better
simple cross sections are available. After extru- erosion properties, a lower contact resistance,
sion they can be further processed by forging, and less tendency to welding than homogeneous
hammering, rolling, or drawing [Rob 91]. materials. Silver and nickel are almost com-
pletely insoluble in each other at room tempera-
5.41.2 Copper and Noble ture. AgNi alloys, therefore, cannot be produced
by melting metallurgy but only by powder met-
Metal-Base Alloys
allurgy. A uniform distribution of the embedded
If powders of electrolytic copper and alumi- nickel is obtained by currentless nickel plating
num oxide are cold isostatically compacted, sin- of silver powder followed by extrusion
tered, and extruded to rods, the very fine Al2O3 [Mue 87].
particles (approximately 0.3 lm), which should As described previously for copper, finely dis-
be finely distributed, prevent recrystallization so tributed particles of cadmium oxide can be
that a high strength is retained up to 1000 ⬚C formed as a dispersoid in silver by internal ox-
[Zwi 57]. idation of alloy powders of the noble metal sil-
Copper alloys with 1.1% aluminum oxide are ver, which practically cannot be oxidized, and
supplied as wire and rods and processed to spot the base metal additive cadmium. The fraction
welding tips. These tips have a very good elec- of cadmium oxide is very high, up to 25%.
trical conductivity and a high flow stress at the Platinum and its alloys, which are used for
welding temperature. At room temperature the special heating wires and other high-temperature
material can be cold worked like copper without components, are dispersion hardened whereby
intermediate annealing. they are extruded as powder mixtures with tho-
The strength-increasing effect up to very high rium oxide, yttrium oxide, or zircon oxide as
temperatures of the aluminum oxide particles as dispersoids [Rob 91].
dispersoids requires extremely fine particles (3–
12 nm) and a uniform distance between them of 5.41.3 Titanium Alloys
less than 0.1 lm. This is achieved by a so-called
A dispersion-hardened titanium alloy is, for
internal oxidation of copper-aluminum powders,
example, a modification of Ti-6242 with 6% Al,
i.e., an oxidizing annealing in which the oxygen
2% Sn, 4% Zr, 2% Mo, 0.1% Si, and 2% Er,
transforms the aluminum to oxide, whereas the
which is produced by internal oxidation during
more noble copper is retained as a metal.
the annealing of the powder Er2O3, with ex-
Dispersion-hardened copper with 0.1 to 0.5
tremely small particles. Of interest is that the
lm large TiB2 particles (3 vol %) is produced
structure obtained by very rapid solidification is
by the following original process.
not changed by extrusion [Rob 91].
Two different copper melts are reacted to-
gether in a reaction vessel whereby the dispersed
5.41.4 Iron Alloys
phase is produced by a precipitation reaction in
situ in the melt. This melt is then atomized to The production of chromium-nickel-steels
powder, which is filled into a copper can and and chromium-aluminum-steels by extrusion of
evacuated [Sut 90]. This material can also be steel powder produced by water atomization was
extruded and processed to spot welding elec- reported in 1969. The process did not go into
trodes. production [Nae 69] because, normally, even
CuSn and CuSnNi alloys with high tin con- with iron alloys the production, or steels using
tents are known as bearing materials but cannot powder, and compaction is more expensive than
be extruded because of the coarse d-phase pre- by melting and casting.
Chapter 5: The Production of Extruded Semifinished Products from Metallic Materials / 297
However, because fewer operating steps are strength is usually obtained by precipitation
needed than between casting and the production hardening.
of the bar and a better homogeneity is obtained, The molten metallurgical production route is
powder extrusion is again being promoted for the most economic solution when possible. It is,
some iron alloys. A Swedish manufacturer of- however, accompanied with coarse precipitates
fers powder metallurgically produced tubes in and reduced hot workability and is not possible
stainless chromium-nickel-steels as well as at all with wide melting intervals.
nickel and cobalt alloys [Asl 81, Rob 91]. The Oxide dispersion strengthened (ODS) alloys
melt is atomized under a protective gas and the are materials in which fine particles, in contrast
powder then cold isostatically compacted in an to precipitates, are also resistant to high tem-
iron can before being extruded over a mandrel. peratures, act as strength increasing dispersions.
The hollow billet also has to be internally en- There is no melting metallurgical alternative to
capsulated to produce tubes. The lubricant is powder metallurgical production. Oxides of yt-
glass, the same as with conventional extrusion, trium are mainly used [Rob 91].
and extrusion is carried out at approximately Table 5.22 summarizes the superalloys pro-
1200 ⬚C. The process is supposed to have eco- duced by P/M.
nomic advantages over the conventional one In the ODS process, the rapidly quenched
[Tus 82]. (more than 103 K/s) powder produced by at-
Some high-speed and tool steels that are se- omization in an inert gas stream after sieving
verely segregated when produced by the normal and mixing is encapsulated in a steel can, which
process are extruded as bar from powder to elim- has to be evacuated at a high temperature to
inate segregations and to retain elements in so- eliminate micropores. If a particularly uniform
lution above the equilibrium value. This is not precipitation-free structure is required, cooling
possible with molten metallurgical production. has to be carried out extremely quickly. Special
Because atomization is usually carried out under rapid solidification rate (RSR) processes have
a protective atmosphere, the round particles that been developed (up to 106 K/s). Extrusion has
do not readily bond have to be encapsulated for proved to be the most suitable compaction
compaction. Water-atomized material can be method with these materials because the large
cold compacted without a can and then sintered deformation breaks up oxide films as described
before extrusion [Rob 91]. for aluminum, disperses impurities present, and
The dispersion hardened iron based alloys provides very good compaction. The encapsu-
MA956 and PM2000 with chromium and alu- lated powder is precompacted by HIP or forging
minium as the main alloying elements and yt- to approximately 85% before it is extruded. The
trium oxide as the dispersoid are described in bars extruded at an extrusion ratio of 5–7 with
the next section. glass lubrication at approximately 1200 ⬚C are
further processed by forging and rolling after re-
5.41.5 Nickel and Cobalt-Base moval of the can. It is possible with extrusion to
significantly reduce the residual porosity and
High-Temperature Alloys
thus the notch impact sensitivity. The extrusion
Alloys with high contents of nickel, chro- temperature with these alloys has to be very
mium, and cobalt are necessary for high-tem- carefully controlled to prevent the risk of coarse
perature applications, particularly in gas turbines precipitates forming at high temperature (e.g.,
and in the aerospace industries. The high carbide in René 95) [Rob 91].
Table 5.22 Composition of some iron and nickel superalloys produced by powder metallurgy
(addition in wt%)
Designation Fe Ni Cr Co Mo W Ti Al Nb Ta Zr B C Y2O3
MA 956(a) 74.0 ... 20.0 ... ... ... 0.5 4.5 ... ... ... ... ... 0.5
PM 2000(b) 73.0 ... 20.0 ... ... ... 0.5 5.5 ... ... ... ... ... 0.5
MA 754(a) 1.0 77.5 20.0 ... ... ... 0.5 0.3 ... ... ... ... 0.05 0.6
MA 6000(a) ... 68.5 15.0 ... 2.0 4.0 2.5 4.5 ... 2.0 0.15 0.01 0.05 1.1
PM 3000(b) ... 67.0 20.0 ... 2.0 3.5 ... 6.0 ... ... 0.15 0.01 0.05 1.1
Renè 95(c) ... 62.0 13.0 8.0 3.5 3.5 2.5 3.5 3.5 ... 0.15 0.01 0.07 ...
Nimonic AP1(a) ... 55.5 15.0 17.0 5.0 ... 3.5 4.0 ... ... ... 0.025 0.02 ...
(a) Inco Alloys International. (b) High temperature metal GmbH. (c) Nuclear Metals Inc. Source: Sch 86, Rue 92
298 / Extrusion, Second Edition
The alloy René 95 and Nimonic AP1 are pre- Because the production of alloy powder would
cipitation-hardening alloys where solid-solution be very expensive, element powders are mixed
hardening is also effective at moderate tempera- and cold compacted. The green blanks are en-
tures because of the addition of molybdenum. cased in aluminum and extruded at approxi-
They are used for gas turbine discs. mately 500 ⬚C. This prevents the extreme exo-
In the ODS alloys Ma 965 and PM2000 (Fe- thermic reaction from the formation of the
Cr-basis), as well as Ma754, Ma 6000, and PM intermetallic phases occurring during the extru-
3000 (Ni-Cr-basis), the Y2O3 is worked into the sion. It takes place—possibly after further de-
metal powder by mechanical alloying in high- formation steps—in high-vacuum furnaces or in
energy ball mills and finely dispersed. The fiber an HIP unit. Another method is “reaction extru-
texture obtained by extrusion is utilized by suit- sion” at such a high temperature that the phase
able heat treatment (coarse-fiber crystals from formation actually occurs during extrusion.
zone recrystallization) to achieve a very good
fatigue and creep strength.
MA956 and PM2000 with high oxidation and
hot corrosion strength up to 1100 ⬚C are used in
combustion chambers, in gas turbines, and other
cases demanding maximum resistance at high Extrusion of Semifinished
temperatures.
MA6000 and PM3000 are used in the first and Products from Metallic
second stages of jet engines and can be hot and Composite Materials
cold rolled after extrusion.
tages. Composite materials are produced today, ● The capability of influencing the deforma-
the metallic components of which form solid so- tion zone by die design
lutions or intermetallic phases corresponding to
the phase diagram or are insoluble in each other. Depending on the materials combination, the
The application of the composite materials is de- materials structure, the application, and the ex-
termined by the adhesion at the boundary faces trusion temperature, metallic composite materi-
of the individual components. The general con- als can be produced by direct, indirect, or hy-
ditions for a satisfactory boundary surface ad- drostatic extrusion.
hesion with common deformation of heteroge-
neous materials include:
● Adequate face pressure (compressive stress
5.42 Terminology and Examples
in the deformation zone)
● Adequate increase in the surface area during
The metalic composites can be classified ac-
the deformation cording to the spatial arrangement of the com-
● A limited inhomogeneity of the flow in the
ponents:
deformation zone that is still sufficient for
the structures to conform to each other but, ● Fiber composite materials
on the other hand, is not so high that the ● Particle composite materials
composite material is subjected to unaccept- ● Penetration composite materials
able internal stresses. The composite com- ● Laminated composite materials
ponents have to be capable of flowing to-
gether under the process-specific stress Figure 5.77 [Lan 93] shows schematically the
conditions. geometric structure.
Composite materials in which fibers of the
For longitudinally orientated semifinished
other components aligned or randomly oriented
products (section, bar, wire, and tubes), the cri-
are embedded, aligned, or randomly orientated
teria described previously for stresses, surface
in the matrix of the predominating component
increase, and flow field formation are fulfilled
by volume are referred to as fiber composite ma-
by the deformation processes rolling, drawing,
extrusion, and (to a limited extent) by forging. terials. Examples are:
However, extrusion provides the most favor- ● Directionally solidified eutectics
able conditions with reference to the three basic ● Copper-sheathed aluminum conductors for
requirements: electrotechnology
● Compressive deformation ● Superconducting materials, including NbTi
● Large strains in one operation multifilaments in a copper matrix
300 / Extrusion, Second Edition
Fig. 5.77 Spatial arrangement of the components in composite materials [Lan 93]
● Electrical contact material, including Ag/C, ● All the components involved are deformed
Ag/Cu/C, and Cu/Pd together whereby different strains can occur
● SiC or B fiber-reinforced light metal mate- within the components.
rials Because the composite materials produced by
Composite materials in which the other com- extrusion are predominantly metallic fiber com-
ponents are embedded without a marked pre- posite materials and the production of dispersion
ferred orientation in the matrix of the predomi- composite materials are described in the section
nating component by volume are referred to as “Extrusion of Powder Metals,” the basic prin-
ciples are described using this type of material.
particle composite materials. They are discussed
The range of possible material combinations,
in the section “Extrusion of Powder Metals.”
which are not fully utilized today, are illustrated
Composite materials in which the various
by way of an example in Fig. 5.78 [Mue 91].
components form an intermingled structure are
Single or multicore wires can be produced as
referred to as penetration composite materials.
well as wires with solid or powder cores. In
Composite materials that have a laminated
some cases, viscous wire fillers (glasses during
structure of the composite materials are referred
hot working) can be used. If thermal material
to as laminated composite materials.
influences and diffusion are taken into account
as well as the structure along with the associated
metallurgical possibilities, the wide range of ma-
terial technical possibilities is clear [Mue 82].
5.43 Flow Behavior in the Extrusion Metallic fiber composite materials, corre-
of Fiber Composite Materials sponding to the structure described (outer tube
and one or more wire cores), can only be pro-
The following cases can be differentiated duced, depending on the application, by indirect
from the point of view of the deformation: or hydrostatic extrusion because the outer tube
cannot have any distortion relative to the core
● Only one or not all of the components are material resulting from adhesion or friction with
deformed (aluminum-steel bus bars, metal the container liner.
powder combinations with ceramic addi- Both in indirect extrusion and hydrostatic ex-
tives). trusion there is no friction between the billet and
Chapter 5: The Production of Extruded Semifinished Products from Metallic Materials / 301
Fig. 5.83 Structure of extruded copper/palladium-composite material. Micrograph image width is approximately 3.6 mm
duction in length of the core wire bundle can ● Buckling of the individual wires or the entire
take place in three ways: bundle
● Twisting of the core wire bundle ● Compression of the core wires
Fig. 5.84 Multicore billet preparation for (a) hydrostatic extrusion and (b) indirect extrusion
Chapter 5: The Production of Extruded Semifinished Products from Metallic Materials / 305
The first two mechanisms do not initially con- in the rod bundle, the support of the casing, and
tain any cross-section increase of the individual the mechanical properties of the material.
wires. There is the risk of the casing buckling or [Mue 81] shows that twisting and buckling
bending giving rise to extrusion defects. The processes can be identified at an L/d ratio of 20
twisting represents energetically the lowest state for a fiber composite material of AlMgSi0.5
and can therefore always be expected. Whether wires; however, no material defect occurs. At an
compression or buckling occurs after twisting L/d ratio of 100, the casing material exhibits
depends on the length-diameter (L/d) ratio of the folding and a defect-free product cannot be ob-
individual rods as well as their mutual support tained.
306 / Extrusion, Second Edition
Fig. 5.86 Different structures in Ag/C (billet diam, 30 mm; bar diam, 12 mm). ZF, number of fibers in sheath tube
Fig. 5.87 Cross section after progressive extrusion stages (bar diam, 12 mm). ZF, number of fibers in the sheath tube
Therefore, the so-called indirect repetitive ex- Ag/Cu/C contact materials is described in more
trusion is a particularly suitable variation of the detail in this chapter [Mue 85]. Silver or copper
indirect extrusion for the production of compos- billets were drilled and filled with graphite pow-
ite materials with complex structures. A billet der for the production of silver/graphite and cop-
made from a specific number of core wires per/graphite composite materials. The diameter
(mantle wires) is extruded to a rod, which is then of the bores was determined by the graphite con-
sectioned and the cross sections reextruded. This tent that had to be achieved. The billets were
process can be repeated as often as required to sealed, preheated to extrusion temperature, and
produce the desired structure. The process se- indirect extruded to bars. After cutting the sec-
quence is shown schematically in Fig. 5.85. tions to length, a specific number of the cross
The process for the production of Ag/C and sections was arranged in a thin-walled silver or
Chapter 5: The Production of Extruded Semifinished Products from Metallic Materials / 307
Fig. 5.89 Process principle for the production of Al-alloy steel composite bus bar
copper casing. The number of bar sections de- ber of fibers in the composite is shown in
pends on the extrusion ratio. Fig. 5.88.
Depending on the extrusion ratio and the
number of extrusion stages, different structures 5.45 Application Examples
can be obtained Fig. 5.86.
The casings were also sealed at both ends and The applications described below subse-
extruded like the powder filled billets. The ex- quently for metallic composite materials pro-
truded multicore bars were again cut to length duced by extrusion can illustrate only a few ar-
and reprocessed as described previously. The se- eas of the comprehensive range. There has been
quential structures can be seen in Fig. 5.87. no attempt to provide a full coverage of all pos-
The relationship between the casing used, the sible and, to some extent, still-experimental ma-
wire diameter, the extrusion ratio, and the num- terials.
308 / Extrusion, Second Edition
5.45.1 Simple Structures and Coatings movement between the steel and the aluminum.
In this way, two-mirror image, composite bus
Lead sheathing of electrical cables can be
bars conductor rails are extruded with a metallic
considered as the oldest and also the most well-
bond between the steel and the aluminum. The
known example of the production of a metallic
reason for simultaneously extruding two com-
composite material. In the mid-1960s, the com- posite sections is to avoid friction between the
posite extrusion of bar, tube, and section became steel strip and the die. In this process the steel
technically important [Ric 69], particularly for band does not contact the die surface but
the processing of reactive metals including be- emerges with no wear. This is achieved as the
ryllium, titanium, zirconium, hafnium, vana- steel strips are completely surrounded by the
dium, niobium, and tantalum. The problem of aluminum and never come into contact with the
attack of the extrusion tooling is a major prob- die bearings. Because the steel strips do not stick
lem in the processing of these metals and their to each other, the two sections can be easily
alloys. Technically, this means that the standard separated from each other. Figure 5.89 shows the
lubricants used in extrusion are not able to guar- process principles.
antee reliable separation between the metals be- Simple composite structures are also found in
ing extruded and the extrusion tooling so that the area of steel- and iron-alloy composite tubes
localized welding occurs. Billets of reactive and sections [Deg 89, Gut 91, Hug 82, Lat 89,
metals have to be clad with a metal that provides Vil 92], as well as aluminum-clad steel wire [Hir
the lubrication as a “lost shell.” Ti/Cu ignition 84] that has excellent corrosion resistance even
electrodes are produced this way. in marine atmospheres and is used as wire cloth
The development of suitable lubricants, and and wire netting.
of low-melting-point glasses in particular, en-
ables conventional extrusion without a cladding
material to be carried out today in many cases. 5.45.2 Metallic Fiber Composite Materials
Cladding with, for example, 18/8 chromium- with Complex Structures
nickel steel, is used today for the extrusion of Outstanding examples in this area are the in-
cast intermetallic materials including NiAl, dustrial metallic superconductors NbTi and
Ni3Al, and TiAl to counteract embrittlement by Nb3Sn [Web 82, Bre 79, Hil 84]. Very different
oxygen absorption at the high extrusion tem- complex structures of usually three or more in-
perature of approximately 1250 ⬚C. dividual components are produced depending on
Since 1963, laminated composite materials of the desired current-carrying capacity. The ex-
copper-clad aluminum for conductors have been amples in Fig. 5.90 shows examples of niobium
developed as a substitute for copper [Hor 70, wires embedded in a copper-tin matrix.
Nyl 78, Fri 67]. The aluminum core consists of Copper forms the core of the composite ma-
EC aluminum, the copper cladding of electro- terial and is separated from the CuSn of the su-
lytic copper. For technical and economic rea- perconductor by a tantalum barrier. Structures
sons, the copper cladding is 15% of the cross- with up to 10,000 individual filaments and a fil-
sectional area. This material is produced only to ament diameter between 3 and 5 lm in wire di-
a limited extent today because of the changes in ameter of 0.4 to 2.0 mm are obtained by multiple
metal prices. combination and followed by multiple extru-
In contrast, the process developed by the com- sion, comparable to the repeated indirect extru-
pany Alusingen for the production of composite sion already described but with a packing den-
electrical bus bars conductors in aluminum-steel sity of 95 to 98%, followed by drawing.
for high-speed and underground trains is com- After the final operation to produce the re-
mercially important [Mie 87]. The basic process quired dimensions, the material is heat treated
is that two alloy steel strips are fed into an ex- to produce the superconducting compound
trusion die. The steel strips are fed from decoil- Nb3Sn by diffusion of the tin from the copper-
ers. They pass through stations for chemical and tin matrix and reaction with the niobium wires.
mechanical pretreatment to apply corrosion pro- The copper core remains unaltered (protected by
tection. They are then fed into the extrusion die the tantalum barrier). Because the supercon-
and turned through 90⬚. Both metals bond to- ducting intermetallic phase Nb3Sn cannot be de-
gether in the welding chamber under the influ- formed, this production route has to be used.
ence of the high extrusion pressure and the in- The possibility of influencing the material
creased temperature as well as the relative and properties by changing the structure and by
Fig. 5.90 Cross section of a filament super conductor [Web 82]
Fig. 5.91 Property comparison between Cu/Pd composite materials (VW) and corresponding Pd/Cu alloys (electrical conductivity
and hardness after cold working)
310 / Extrusion, Second Edition
Fig. 5.92 Schematic process for reaction powder metallurgy. (a) Longitudinal and transverse structure of Ti48.5Al, unreacted.
(b) Longitudinal and transverse sections in the extruded state
specific heat treatments can be applied to other Pd composite alloys a high ductility (Fig. 5.91).
materials. The work by [Sto 87] and [Mue 86] This provides excellent further processing pos-
describes the contact material copper palla- sibilities, providing savings in the noble metals
dium. Palladium-copper alloys with 15 or 40 and economic production processes for com-
wt% Cu are used extensively for contact ma- plex components.
terials for switching direct current because of
their high resistance to material movement. Pal-
ladium and copper form a continuous solid-so-
5.45.3 Metallic Fiber Composite
lution series with superstructure phases. This
governs the electrical conductivity of the alloys. Materials with P/M Structures
There are significant technical and economic This application area includes all those fiber
advantages in using Cu/Pd composite materials composite materials that can be produced from
instead of conventional PdCu alloys. Care powder starting materials. These are mainly alu-
should be taken to avoid the formation of solid- minum-base fiber-reinforced materials [Sch 87,
solution zones at the boundary surface between Ros 92, Bei 90, Moo 85], metal matrix compos-
copper and palladium in the manufacture of the ites (MMC) [Sta 88], and materials for electrical
composite materials. It is possible, by control- contacts [The 90]. The production of fibers [Boe
ling the structure and the temperature in the de- 88] also provides a means of materials strength-
formation process, to obtain the microscopic ening.
heterogeneous composite structure. The indirect Alloys based on the intermetallic phase TiAl
extrusion of coils of copper and palladium strip have a large potential for use as high-tempera-
is particularly suited for this. This produces ture, light structural components. The deforma-
contact materials that exhibit a completely dif- tion potential of this phase, which is usually brit-
ferent property spectrum compared with con- tle under a conventional stress state, is very
ventional alloys of the same composition. The limited. Semifinished and structural components
electrical and thermal conductivities of Cu/Pd can be produced economically by reaction pow-
composite materials are up to 10 times higher der metallurgy [Mue 90, Wan 92, Mue 93] (see
than the corresponding Cu-Pd alloys. The ab- also the section “Extrusion of Powder Metals”).
sence of solid-solution hardening gives the Cu/ The production of titanium aluminides by reac-
Chapter 5: The Production of Extruded Semifinished Products from Metallic Materials / 311
tion powder metallurgy (Fig. 5.92a) includes the [Ach 69]: D. Achenbach and G. Scharf, Z. Me-
following steps: tallkd., Vol 60, 1969, p 915–921
1. Mixing the initial powders (element and/or [Ake 68]: R. Akeret, Untersuchungen über das
alloy powders) Strangpressen unter besonderer Berücksichti-
2. Precompaction of the powder mixture (e.g., gung der thermischen Vorgänge (Investiga-
by CIP) tions into the Extrusion with Specific Rein-
3. Production of semifinished product by extru- forcement to the Thermal Processes),
sion Aluminium, Vol 44, 1968, p 412–415
4. Finishing of component [Ake 70]: R. Akeret, Untersuchungen über das
5. Reaction heat treatment Umformverhalten von Aluminiumwerkstof-
fen bei verschiedenen Temeraturen (Investi-
Figure 5.92(b) shows longitudinal and trans- gations into the Deformation Behavior of
verse sections in the extruded state. Suitable Aluminum Alloys at Different Temperatures),
control of the reaction heat treatment produces Z. Metallkd., Vol 61, 1970, p 3–10
the phase TiAl expected from the phase diagram. [Ake 71]: R. Akeret, Die Produktivität beim
In the future, it should be possible for starting Strangpressen von Aluminium-Werkstof-
materials that have been produced by mechani- fen—Einfluß von Werkstoff und Verfahren
cally alloyed powder particles or by a spray (The Productivity in the Extrusion of Alumi-
compaction process to be used for the applica- num Alloys—Influence of the Material and
tion of new composite materials with excellent Process), Z. Metallkd., Vol 62, 1971, p 451–
properties. 456
[Ake 72]: R. Akeret, Filage de l’aluminium: An-
REFERENCES alyse des phénomènes thermiques pour dif-
férentes conditions opératiores (Aluminum
Extrusion of Materials with Working Tem- Extrusion: Analysis of the Thermal Phenom-
peratures between 0 and 300 ⬚C enon for Different Operational Conditions),
[Hof 62]: W. Hofmann, Blei und Bleilegierun- Mém. Sci. Rev. Mét., Vol 69, 1972, p 633–640
gen, Metallkunde und Technologie (Lead and [Ake 72a]: R. Akeret, Properties of Pressure
Lead Alloys, Metallurgy and Technology), Vol Welds in Extruded Aluminium Alloy Sec-
2, I, Bildsame Formgebund, Springer-Verlag, tions, J. Inst. Met., Vol 100, 1972, p 202–207
1962 [Ake 73]: R. Akeret, Sonderverfahren zum
[Lau 76]: K. Laue and H. Stenger, Strangpres- schnelleren Strangpressen von Aluminium-
sen: Verfahren, Maschinen, Werkzeuge (Ex- Hartlegierungen (Special Processes for Faster
trusion: Processes, Machines, Tools), Alumin- Extrusion of Aluminum Hard Alloys), Z. Me-
ium, 1976 tallkd., Vol 64, 1973, p 311–319
[Sac 34]: G. Sachs, Spanlose Formung (Chip- [Ake 80]: R. Akeret, Das Verhalten der Strang-
less Forming), Metallkunde, Springer-Verlag, presse als Regelstrecke (Aluminum Extrusion
1934 as a Controlled System), Metall., Vol 34,
[Schi 77]: P. Schimpke, H. Schropp, and R. 1980, p 737–741
König, Technologie der Maschinenbauwerk- [Ake 83]: R. Akeret, Einfluß der Querschnitts-
stoffe (Technology of Materials for Machine form und der Werkzeuggestaltung beim
Construction), Vol 18, S. Hirzel Verlag Stutt- Strangpressen von Aluminium (Influence of
gart, 1977, ISBN 3-7776-0312-0 the Cross-Section Profile and Tool Design on
[Schu 69]: M. Schumann, Metallographie (Met- the Extrusion of Aluminum), Teil I: Vorgänge
allography), Vol 7, VEB Deutscher Vertag für in der Umformzone (Part 1: Processes in the
Grundstoffindustrie, Leipzig, 1969 Deformation Zone), Aluminium Vol 59, 1983,
p 665–669, 745–750
[Ake 85]: R. Akeret, Einfluß des Neigungswin-
REFERENCES kels und der Länge der Laufflache auf die Rei-
bung im Preßkanal (Influence on the Inclina-
Extrusion of Materials with Deformation tion Angle and the Length of the Bearing
Temperatures between 300 and 600 ⬚C Surface on the Friction in the Die Aperture),
[Abt 96]: S. Abtahi, T. Welo, and S. Stören, In- Aluminium, Vol 61, 1985, p 169–172
terface Mechanisms on the Bearing Surface [Ake 86]: R. Akeret and W. Strehmel, “Heat
in Extrusion, ET ’96, Vol II, p 125–131 Balance and Exit Temperature Control in the
312 / Extrusion, Second Edition
Extrusion of Aluminium Alloys,” Vol IV, Pa- Technology ’86, The Institute of Metals, Lon-
per 114 presented at Aluminium Technology don, England, 1986
’86, The Institute of Metals, London, En- [Clo 90]: M.P. Clode and T. Sheppard, Forma-
gland, 1986 tion of Die Lines during Extrusion of AA
[Ake 88]: R. Akeret, A. Reid, and J.-J. Théler, 6063, Mater. Sci. Technol.,Vol 6, 1990, p 755–
Qualitätsanforderungen an AlMggSi0,5- 763
Preßbolzen, (Quality Requirements for [Cre]: R.A. Creuzet, FP 69 42347, USP 3 748
ALMgSi 0.5 Billets), Metall., Vol 42, 1988, p 885
760–769 [Czi 72]: H. Czichos, The Mechanism of the
[Ake 88a]: R. Akeret and W. Strehmel, Control Metallic Adhesion Bond, J. Phys. D. Appl.
of Metal Flow in Extrusion Dies, ET ’88, Vol Phys., Vol 5, 1972, p 1890–1897
II, p 357–367 [Dah 93]: Umformtechnik, Plastomechanik und
[Ake 92]: R. Akeret, Strangpreßnähte in Alu- Werkstoffkunde (Deformation Technology,
miniumprofilen, Teil I: Technologie, Teil II: Plastomechanics and Material Science), W.
Mikrostruktur und Qualitätsmerkmale (Extru- Dahl and R. Kopp, Ed., Springer-Verlag,
sion Welds in Aluminum Sections, Part 1: 1993, p 707–711
Technology, Part II: Microstructure and Qual- [DGM 78]: Atlas der Warmformgebungseigen-
ity Characteristics), Aluminium, Vol 68, 1992, schaften, Bd I, Aluminiumwerkstoffe (Atlas of
p 877–887, 965–974 Hot-Working Properties, Vol 1, Aluminum Al-
[Ast 75]: E.I. Astrov, zitiert in [Gil 75]: (men- loys), Deutsche Gesellschaft für Metallkunde,
tioned in [Gil 75]), Lit. 55 Oberursel, Germany, 1978
[Auk 96]: T.u.M. Aukrust, Texture and Surface [Die 66]: K. Dies and P. Wincierz, Z. Metallkd.,
Grain Structure in Aluminium Sections, ET Vol 57, 1966, p 141–150, 227–232
’96, Vol I, p 171 [Dor 73]: R.C. Dorward, Metall. Trans., Vol 4,
[Bag 81]: J. Baumgarten, Materialfluß beim di- 1973, p 507–512
rekten Strangpressen von Aluminium (Mate- [Eul 75]: J. Eulitz and G. Scharf, Aluminium,
rial Flow in Direct Extrusion of Aluminum), Vol 51, 1975, p 214–218
Aluminium, Vol 57, 1981, p 734–736 [Fin 92]: W.-D. Finkelnburg and G. Scharf,
[Bat 79]: A.I. Baturin, Heat Generation and Ef- Some Investigations of the Metal Flow during
fectiveness of Heat Removal in Extrusion, Extrusion of Al Alloys, ET ’92, Vol II, p 475–
Tekhnol. Legk. Splavov (No. 5), 1979, p 21– 484
25 (in Russian) [Fin 96]: W.-D. Finkelnburg, G. Scharf, and G.
[Bau 71]: M. Bauser and G. Fees, Oberfläch- Tempus, Proceedings 6th Int. Aluminum Ex-
enfehler bei stranggepreßten Profilen aus trusion Seminar (Chicago, IL), 1996
AlMgSi-Legierungen (Surface Defects in [Fuc 96]: Otto Fuchs Metallwerke, prospekte
AlMgSi Alloy Extruded Sections), Z. Me- (brochure)
tallkd., Vol 62 (No. 10), 1971, p 705–710 [Gat 54]: F. Gatto, “Fondamenti della teoria
[Bau 82]: M. Bauser and E. Tuschy, State of the dell’estrusione Alluminio,” Vol 23, 1954, p
Art and Future Development of Extrusion, 533–545
Extrusion, Scientific and Technical Develop- [Gil 75]: M.S. Gildenhorn, W.G. Kerov, and
ment, Deutsche Gesellschaft für Metallkunde, G.A. Krivonos, Strangpreßschweißen von
Oberursel, Germany, 1982, p 7–15 Hohlprofilen aus Aluminiumlegierungen (Ex-
[Bec 39]: A. Beck, Magnesium und Seine Le- trusion Welding of Hollow Sections in Alu-
gierungen (Magnesium and Its Alloys), minum Alloys), Metallurgia, Moskau, 1975
Springer-Verlag, Berlin, 1939 (Russ., Teilübersetzung durch Forschung-
[Bry 71]: H.J. Bryant, Metallurgical Investiga- szentrum Strangpressen, Berlin, 1995)
tion of Defects in Hot Extruded Aluminium [Gru 66]: W. Gruhl and G. Scharf, Z. Metallkd.,
Alloys, Z. Metallkd., Vol 62, 1971, p 701–705 Vol 57, 1966, p 597–602
[Bry 75]: W.A. Bryant, A Method for Specify- [Har 47]: C.S. Harris, Extrusion of Magnesium,
ing Hot Isostatic Pressure Welding Parame- Wiederdruck aus Machinery, March 1947
ters, Weld. J., Vol 54, 1975, p 733s [Har 94]: J.-P. Hardouin, Procédé et dispositiv
[Clo 86]: M.P. Clode and T. Sheppard, “Surface d’extrusion-filage d’un alliage d’aluminium à
Generation and the Origin of Defects during bas titre, Franz, Patent 94 14143, Nov 25,
Extrusion of Aluminium Alloys,” Paper 51 1994
presented at Tagungsbericht Aluminium [Hir 58]: J. Hirst and D.J. Ursell, Some Limiting
Chapter 5: The Production of Extruded Semifinished Products from Metallic Materials / 313
Factors in Extrusion, Metal Treatment, Vol trusion: Processes, Machining, Tooling), Al-
25, 1958, p 409–413, 416 uminium Verlag GmbH, 1976
[Hob 91]: Metallkunde: Aufbau und Eigen- [Lef 92]: M. Lefstad, O. Reiso, and V. Johnsen,
schaften von Metallen und Legierungen (Met- Flow of the Billet Surface in Aluminium Ex-
allurgy, Structure and Properties of Metals trusion, ET ’92, Vol II, p 503–517
and Alloys), E. Hornbogen and H. Warlimont, [Lef 96]: M. Lefstad and O. Reiso, Metallurgical
Ed., Vol 2, Springer Lehrbuch, 1991 p 202 Speed Limitations during the Extrusion of
[Hon 68]: Aluminium, Vol III, Fabrication and AlMgSi-Alloys, ET ’96, Vol I, p 11–21
Finishing, third printing, Kent R. van Horn, [Lyn 71]: C.V. Lynch, Die Auswirkung der Fa-
Ed., American Society for Metals, 1968, p 95 brikationsbedungungen auf die Qualität von
[Jel 79]: J.L. Jellison, Effect of Surface Contam- Preßprofilen aus der Legieung AlMgSi0,5
ination on Solid Phase Welding—An Over- (The Effect of the Fabrication Conditions on
view, Proc. Conf. Surface Contamination: the Quality of Extruded Sections in the Alloy
AlMgSi0.5), Z. Metallkd., Vol 62 (No. 10),
Genesis, Detection and Control (Washing-
1971 p 710–715
ton), 1978, Vol II, Plenum Press, New York,
[Mie 62]: K. Mietzner, Untersuchungen über die
1979, p 899–923 Oberflächenbeschaffenheit stranggepreßter
[Joh 96]: V.I. Johannes and C.W. Jowett, Tem- Profile aus Al-Legierungen (Investigations
perature Distribution in Aluminium Extrusion into the Surface Condition of Extruded Al Al-
Billets, ET ’96, Vol I, p 235–244 loy Sections), Metall., Vol 16, 1962, p 837–
[Joh 96a]: V.I. Johannes, C.W. Jowett, and R.F. 843
Dickson, Transverse Weld Defects, ET ’96, [Moe 75]: M. Möller and P. Wincierz, Grob-
Vol II, p 89–94 kornbildung bei Preßstangen aus aushärt-
[Kie 65]: O. Kienzle and K. Mietzner, Atlas um- baren manganhaltigen Aluminiumwerkstof-
geformter Oberflächen (Atlas of Deformed fen (Coarse Grain Formation in Extruded Bar
Surfaces), Springer-Verlag, 1965 in Age-Hardening Manganese Containing
[Koe 61]: K. Köstlin and O. Schaaber, Härterei- Aluminum Alloys), 6, Internationale Leich-
Technik und Wärmebehandlung (Hardening metalltagung (Leoben-Vienna), 1975, p 139–
Technology and Thermal Treatment), Vol 16, 141
1961, p 150–156 [Moo 96]: H.G. Mooi, A.J. den Bakker, K.E.
[Kra 93]: C. Kramer and D. Menzel, Konvek- Nilsen, and J. Huétink, Simulation of Alu-
tionskühlsysteme für Leichtmetallhalbzeuge minium Extrusion Based on a Finite Element
(Convection Cooling Systems for Aluminum Method (FEM), ET ’96, Vol II, p 67–73
Semifinished Products), Aluminium, Vol 69, [Mue 96]: K.B. Müller and J. Wegener, Direct
1993, p 247–253 Extrusion of AA6060 through Dies with
[Lag 72]: G. Lange, Der Wärmehaushalt beim Coated Bearing Lengths, ET ’96, Vol II, p
Strangpressen Teil I: Berechnung des isoth- 147–153
ermen Preßvorganges (Heat Balance in Extru- [Oph 88]: G.A. Oude Ophuis, The Extrumax
sion, Part 1: Analysis of the Isothermal Ex- System: A New Dimension in the Extrusion
trusion Process), Z. Metallkd., Vol 62, 1972, Process, A New and Optimal Way to Extrude
p 571–577 Section, ET ’88, Vol 1, p 181–187
[Par 96]: N.C. Parson, C.W. Jowett, W.C. Fra-
[Lan 82]: J. Langerweger, Metallurgische Ein-
ser, and C.V. Pelow, Surface Defects on
flüsse auf die Produktivität beim Strangpres-
6XXX Extrusions, ET ’96, Vol I, p 57–67
sen von AlMgSi-Werkstoffen (Metallurgical [Rei 84]: O. Reiso, The Effect of Composition
Influences on the Productivity of the Extru- and Homogenization Treatment on Extruda-
sion of AlMgSi Alloys), Aluminium, Vol 58, bility of AlMgSi Alloys, ET ’84, Vol l, p 31–
1982, p 107–109 40
[Lan 84]: J. Langerweger, Correlation between [Rei 88]: O. Reiso, Proc. 4th Int. Aluminium
Properties of Extrusion Billets, Extrudability Extrusion Technology Seminar (Chicago, IL),
and Extrusion Quality, ET ’84, Vol I, p 41–45 Aluminium Association, 1988, Vol 2, p 287–
[Lau 60]: K. Laue, Isothermes Strangpressen 295
(Isothermal Extrusion), Z. Metallkd., Vol 51, [Ros]: M. Rossmann, Verfahren zum Strang-
1960, p 491–495 pressen bzw (Processes for Extrusion and
[Lau 76]: K. Laue and H. Stenger, Strangpres- Drawing), Strangziehen. Europ. Pat. 0 210
sen: Verfahren, Maschinen, Werkzeuge (Ex- 568 B1
314 / Extrusion, Second Edition
[Rup 77]: D. Ruppin and W. Strehmel, Direktes bution to Extrusion with Cooled Tools), Alu-
Strangpressen mit konstanter Austrittstemper- minium, Vol 55, 1979, p 197–201
atur—Einsatz axialer Blocktemperaturprofile [Sca 82]: G. Scharf and B. Grzemba, Alumin-
(Direct Extrusion with Constant Exit Tem- ium, Vol 58, 1982, p 391–397
perature—Application of Axial Billet Tem- [Sch 79]: H.-E. Scholz, “Werkstoffkundliche,
perature Profile), Aluminium, Vol 53, 1977, p experimentelle und theoretische Unter-su-
233–239 chungen zur Optimierung des Strangpressens
[Rup 77a]: D. Ruppin and W. Strehmel, Direk- metallischer Werkstoffe (Verfahren, Thermo-
tes Strangpressen mit konstanter Austrittstem- dynamik, Preßrechnung, Simulation, Gestal-
peratur—Einsatz variabler tung),” (“Metallurgical, Experimental and
Preßgeschwindigkeit (Direct Extrusion with Theoretical Investigation to Optimize the Ex-
Constant Exit Temperature—Application of trusion of Metallic Materials [Process, Ther-
Variable Extrusion Speed), Aluminium, Vol modynamics, Extrusion Calculation, Simula-
53, 1977, p 543–548 tion, Shape]”), dissertation, RWTH-Aachen,
[Rup 82]: D. Ruppin and K. Müller, Pressen 1979
über stehenden Dorn verbessert die Rohrin- [Scw 84]: P. Schwellinger, H. Zoller, and A.
nenfläche (Extrusion over a Fixed Mandrel Maitland, Medium Strength AlMgSi Alloys
Improves the Tube Internal Surface), Maschi- for Structural Applications, ET ’84, Vol l, p
nenmarkt, Würzburg, Germany, Vol 88, 1982, 17–20
p 2089–2091 [Sel 84]: R.J. Selines, C. Goff, P. Cienciwa, and
[Rup 83]: D. Ruppin and W. Strehmel, Auto- F. Lauricella, Extrusion Cooling and Inerting
matisierung des Preßprozesses beim direkten Using Liquid Nitrogen, ET ’84, Vol l, p 222–
Strangpressen von Aluminiumwerkstoffen 226
(Automation of the Extrusion Process in the [She 77]: T. Sheppard, The Application of Limit
Direct Extrusion of Aluminum Alloys), Alu- Diagrams to Extrusion Process Control, ET
minium, Vol 59, 1983, p 674–678, 773–776
’77, Vol I, p 331–337
[Sac 34]: G. Sachs, Metallkunde—Spanlosetor-
[She 88]: T. Sheppard and M.P. Clode, The Or-
mung (Metallurgy—Chipless Forming),
igin of Surface Defects during Extrusion of
Springer-Verlag, 1934
AA 6063 Alloy, ET ’88, Vol II, p 329–341
[Sah 96]: P.K. Saha, Influence of Plastic Strain
[Shu 69]: M. Schumann, Metallographie (Met-
and Strain Rate on Temperature Rise in Alu-
minium Extrusion, ET ’96, Vol I, p 355–360 allography), Vol 7, VEB Deutscher Verlag für
[Sca 64]: G. Scharf, Z. Metallkd., Vol 55, 1964, Grundstoffindustrie, Leipzig, Germany, 1969
p 740–744 [Ska 96]: I. Skauvik, K. Karhausen, M. Melan-
[Sca 65]: G. Scharf, VDI-Nachrichten, Vol 19, der, and S. Tjötta, Numerical Simulation in
1965, p 6–8 Extrusion Die Design, ET ’96, Vol II, p 79–
[Sca 67]: G. Scharf, D. Achenbach, and W. 82
Gruhl, Metall., Vol 21, 1967, p 183–189 [Spe 84]: P.R. Sperry, Correlation of Micro-
[Sca 69]: G. Scharf and W. Gruhl, Einfluß von structure in 6XXX Extrusion Alloys with Pro-
Ausscheidungen auf Warmverformung und cess Variables and Properties, ET ’84, Vol I,
Rekristallisationsverhalten von Aluminiumle- p 21–29
gierungen (Influence of Precipitates on the [Sta 90]: P. Staubwasser, “Der Einfluß des Ge-
Hot-Working and Recrystallization Behavior füges auf das dekorative Aussehen anodi-
of Aluminum Alloys), Aluminium, Vol 45, sierter AlMgSi0,5 Profile” (“The Influence of
1969, p 150–155. the Structure on the Decorative Appearance
[Sca 69a]: G. Scharf and W. Gruhl, Z. Metallkd., of Anodized AlMgSi0.5 Sections”), disserta-
Vol 60, 1969, p 413–421 tion, Aachen, Germany, 1990
[Sca 69b]: G. Scharf and D. Achenbach, Z. Me- [Ste 73]: H. Stenger, Die maximale
tallkd., Vol 60, 1969, p 904–909 Preßgeschwindigkeit beim Strangpressen
[Sca 73]: G. Scharf and J. Eulitz, Aluminium, (The Maximum Speed in Extrusion), Drah-
Vol 49, 1973, p 549–552 twelt, Vol 59, 1973, p 235–240
[Sca 78]: G. Scharf and E. Lossack, Metall., Vol [Str 96]: W. Strehmel, M. Plata, and B. Bourqui,
32, 1978, p 550–560 New Technologies for the Cooling and
[Sca 79]: G. Scharf, Ein Beitrag zum Strang- Quenching of Medium-to-Large-Sized Alu-
pressen mit gekühltem Werkzeug (A Contri- minium Extrusions, ET ’96, Vol I, p 317–325
Chapter 5: The Production of Extruded Semifinished Products from Metallic Materials / 315
paction), Pulvermetallurgie (Powder Metal- [Mue 87]: K. Müller, and D. Ruppin, Anwen-
lurgy), DGM-Fortbildungsseminar, Dresden, dungsmöglichkeiten des indirekten Strang-
1982 pressens zur Herstellung metallischer Ver-
[Arn 92a]: V. Arnhold, K. Hummert, and R. bundwerkstoffe (Possible Applications of
Schattevoy, PM-Hochleistungsaluminium für Indirect Extrusion to the Production of Me-
motorische Anwendungen— tallic Composite Materials), Metall., Vol 41,
maßgeschneiderte Legierungen und entspre- 1987, p 8
chende Verfahren (High-Strength Aluminum [Mue 93]: K. Müller and A. Grigoriev, Direct
for Motor Applications—Custom Made Al- and indirect Extrusion of Al-18SiCu-Mg-Ni,
loys and Corresponding Processes), VDI-Ber- Proc. Int. Conf. Aluminum Alloys (Atlanta,
ichte (VDI-Reports), No. 917, 1992 GA), Sept 1993
[Asl 81]: C. Aslund, G. Gemmel, and T. An- [Mur 96]: H.R. Müller, Eigenschaften und Ein-
dersson, Stranggepreßte Rohre auf pulver- satzpotential sprühkompaktierter Kupferlegi-
metallurgischer Basis (Extruded Powder Met- erungen (Properties and Potential Applica-
allurgy Tubes), Bänder Bleche Rohre, Vol 9, tions of Spray-Compacted Copper Alloys),
1981, p 223–226 Universität Bremen, Sonderforschungsber-
[Boe 89]: W. Boeker and H.J. Bunge, Verfor- eich 372, “Sprühkompaktieren,” Kolliquium,
mungsverhalten zweiphasiger metallischer Vol 1, 1996
Werkstoffe (Deformation Behavior of Binary [Nae 69]: G. Naeser and O. Wessel, Herstellung
Phase Metallic Materials), Verbundwerkstoffe von Stäben und Rohren aus Metallpulvern
und Stoffverbunde in Technik und Medizin, durch Strangpressen (Production of Bars and
1989, p 183–188 Tubes from Metal Powders by Extrusion),
[Cra 88]: A.W. Cramb, New Steel Casting Pro- Arch. Eisenhüttenwes., Vol 40, 1969, p 257–
cesses for Thin Slabs and Strip—A Historical 262
Perspective, Iron Steelmaker, Vol 7, 1988, p [Rob 91]: P.R. Roberts and B.L. Ferguson, Ex-
45–60 trusion of Metal Powders, Int. Mater. Rev., Vol
[Gro 73]: J. Grosch, “Kaltpreßschweißen von 36, 1991, p 62–79
Aluminiumpulver durch Strangpressen” [Rue 92]: M. Rühle and Th. Steffens, Legi-
(“Cold Pressure Welding of Aluminum Pow- erungsbildung und Amorphisation beim me-
ders by Extrusion”), Diskussionstag Strang- chanischen Legieren (Alloy Formulation and
pressen, 1973 Amorphization with Mechanical Alloying),
[Hum 97]: K. Hummert, PM-Aluminium als Metall., Vol 46, 1992, p 1238–1242
Hochleistungswerkstoff-Entwicklung, Her- [Sch 86]: W. Schatt, Pulvermetallurgie—Sinter
stellung und Anwendung. Neuere Entwicklun- und Verbundwerkstoffe (Powder Metal-
gen in der Massivum-formung (PM Aluminum lurgy—Sintered and Composite Materials),
as High Strength Material—Development Vol 2, Dr. Alfred Hüthig,Verlag, 1986
Production and Application. New Develop- [Sha 87]: G. Scharf and I. Mathy, Entwicklung
ments in Massive Deformation), Verlag DGM von Aluminium-Knetwerkstoffen aus schnell
Informationsgesellschaft, 1997 erstarrten Legierungspulvern (Development
[Inc 86]: Inco Alloys International: Plant In- of Aluminum Wrought Materials from Rap-
vestments for Superalloy Production, Metal- idly Solidified Alloy Powders), Metall., Vol
lurgia, Redhill, Vol 53, 1986, p 509–512 41, 1987, p 608–616
[Irm 52]: R. Irmann, Sintered Aluminium with [Sha 87a]: G. Scharf and G. Winkhaus, Techn-
High Strength at Elevated Temperatures, Me- ische Perspektiven der Aluminiumwerkstoffe
tallurgia, 1952, p 125–133 (Technical Perspectives of the Aluminum Al-
[Jan 75]: G. Jangg, F. Kutner, and G. Korb, Her- loys), Aluminium, Vol 63, 1987, p 788–808
stellung und Eigenschaften von dispersions- [Sut 90]: Sutec: “New Dispersion-Strengthened
gehärtetem Aluminium (Production and Prop- Electrodes,” prospekt (brochure), 1990
erties of Dispersion Hardened Aluminum), [Tus 82]: E. Tuschy, Literaturübersicht: Strang-
Aluminium, Vol 51, 1975, p 6 pressen—Neue Verfahren (Literature Review:
[Man 88]: “Mannesmann-Demag: Sprühkom- Extrusion—New Process), Metall., Vol 36,
paktieren—Das Osprey-Verfahren” (“Spray 1982, p 269–279
Compaction—The Osprey Processes Bro- [Wei 86]: W.G. Weiglin, Pulvermetallurgie—
chure”), Prospekt Mannesmann Demag Hüt- eine Zukunftstechnologie im Krupp Konzern
tentechnik, Duisburg, Germany, 1988 Sie und wir—Information der Krupp Stahl AG
Chapter 5: The Production of Extruded Semifinished Products from Metallic Materials / 321
(Powder Metallurgy—A Technology for the [Mue 82]: K. Müller and Ruppin, Extrusion,
Future in Krupp. You and Us International on Scientific and Technical Developments
Krupp Steel AG), Jan 1986, p 34–37 DGM-Tagungsband, Symposium Strangpres-
[Zwi 57]: K.M. Zwilsky and N.J. Grant, J. Met., sen, 1982, p 233–245
Vol 9, 1957, p 1197–1201 [Mue 85]: K. Müller, D. Ruppin, and D. Stö-
ckel, Z. Metallkd., Vol 39, 1985, p 26–30
[Mue 86]: K. Müller, D. Stöckel, and H. Claus,
REFERENCES
Z. Metallkd., Vol 40, 1986, p 33–37
Extrusion of Semifinished Products from Me- [Mue 90]: K. Müller, Proc. Third JCTP Kyoto,
tallic Composite Materials Advanced Technology of Plasticity, Vol 1,
1990, p 329–334
[Ahm 78]: N. Ahmed, J. Mech. Work. Technol., [Mue 91]: K. Müller, Neuere Entwicklungen in
Vol 2, 1978, p 19–32 der Massivumformung (New Developments in
[Bei 90]: R. Beier, Technica, Zürich, Vol 39, the Large Scale Working), K. Siegert, DGM
1990, p 76–80 Informationsgesellschaft, Verlag, 1991, p
[Boe 88]: W. Böcker and H.J. Bunge, Z. Me- 369–387
tallkd., Vol 42, 1988, p 466–471 [Mue 93]: K. Müller, X. Neubert, et al.,
[Bre 79]: I. Breme and H. Massat, Z. Metallkd., Proc.Third Japan International Sampe Sym-
Vol 33, 1979, p 597–601 posium, 1993, Vol 2, p 1564–1569
[Deg 89]: H.P. Degischer and K. Spiradek, Ver- [Nyl 78]: C.G. Nylunal, ASEA zeitschrift (peri-
bundwerkstoffe und Stoffverbunde in Technik
odical), 1978, p 3–10
und Medizin (Composite Materials in Engi-
[Osa 73]: K. Osakada et al., Int. J. Mech. Sci.,
neering and Medicine), 1989, p 31–39
Vol 15, 1973, p 291–307
[Fri 67]: G.H. Frieling, Wire W. Prod., Vol 42,
[Rau 78]: G. Rau, Metallische Verbundwerk-
1967, p 72–76
stoffe (Metallic Composite Materials), Werk-
[Gut 91]: I. Gutierrez, J.J. Urcola, J.M. Bilbao,
stofftechnische Verlagsgesellschaft, Karls-
and L.M. Vilar, Mater. Sci. Technol., Vol 7,
ruhe (Material technical publishing house
1991, p 761–769
[Hil 84]: H. Hillmann, Z. Metallkd., Vol 38, company, Karlsruhe), 1978
1984, p 1066–1071 [Ric 69]: H. Richter, Z. Metallkd., Vol 60, 1969,
[Hir 84]: M. Hirato, M. Onuki, and K. Kimura, p 619–322
Wire J. Int., Vol 17, 1984, p 74–81 [Ros 92]: D. Roß, “VDI Fortschrittsberichte
[Hol 78]: C. Holloway and M.B. Bassett, J. Reihe 5” (“VDI Progress Report Series 5”),
Mech. Work. Technol., Vol 2, 1978, p 343–359 No. 282, 1992
[Hor 70]: N. Hornmark and D. Ermel, Drah- [Rup 80]: D. Ruppin and K. Müller, Aluminium,
twelt, Vol 56, 1970, p 424–426 Vol 56, 1980, p 523–529
[Hug 82]: K.E. Hughes and C.M. Sellars, Met. [Sch 87]: G. Scharf and G. Winkhaus, Alumin-
Technol., Vol 9, 1982, p 446–452 ium, Vol 63, 1987, p 788–808
[Lan 93]: K. Lange, Umformtechnik (Defor- [Sta 88]: M.H. Stacey, Mater. Sci. Technol., Vol
mation Technology), Vol 4, Springer-Verlag, 4, 1988, p 227–230
1993 [Sto 86]: D. Stöckel, Metall., Vol 40, 1986, p
[Lat 89]: E.P. Latham, D.B. Meadowkroft, and 456–462
L. Pinder, Mater. Sci. Technol., Vol 5, 1989, [Sto 87]: D. Stöckel, K. Müller, and H. Claus,
p 813–815 Z. Metallkd., Vol 41, 1987, p 702–706
[Mie 87]: G. Mier, Schweizerische Aluminium [The 90]: W.W. Thedja and D. Ruppin, Z. Me-
Rundschau (Swiss Aluminum Observer), tallkd., Vol 44, 1990, p 1054–1061
1987, p 12–17 [Vil 92]: L. Villar, Stainl. Steel Eur., Vol 4, 1992,
[Moo 85]: T. Mooroka, Ch. Kawamura, et al., p 38–39
Aluminium, Vol 61, 1985, p 666–669 [Wan 92]: G.X. Wang and M. Dahms, PMI, Vol
[Mue 80]: K. Müller et al., Z. Maschinenmarkt, 24, 1992, p 219–225
Vol 86, 1980, p 34, 37, 38; K. Osakada et al., [Web 82]: H.R. Weber, Extrusion, Scientific and
Int. J. Mech. Sci., Vol 15, 1973, p 291–307 Technical Developments DGM-Tagungs-
[Mue 81]: K. Müller and D. Ruppin, Z. Werk- band, Symposium Strangpressen, 1982, p
stofftech., Vol 12, 1981, p 263–271 277–296
Extrusion: Second Edition Copyright © 2006 ASM International®
M. Bauser, G. Sauer, K. Siegert, editors, p 323-416 All rights reserved.
DOI:10.1361/exse2006p323 www.asminternational.org
CHAPTER 6
6.1 Machinery and Equipment for extrude. Wire, bar, section, hollow sec-
Direct and Indirect Hot Extrusion tion, and wide flat sections
b. Copper and copper alloys including brass
THE MACHINERY AND EQUIPMENT re- (heavy metal) easy to extrude and/or dif-
quired for rod and tube extrusion is determined ficult to extrude. Wire, bar, and section
by the specific extrusion process, as previously c. Steel and high-strength steel alloys easy
discussed in Chapter 3, “Rod and Tube Extru- to extrude and/or difficult to extrude. Sec-
sion Processes.” tion
● Process technology
Ideally, the machinery and equipment should
have flexibility but, also, provide specific extru- a. Extrusion without lubrication and without
sion process with the optimum quality and eco- a shell
nomic efficiency. As discussed in Chapter 3, di- b. Extrusion without lubrication and with a
rect hot extrusion is the most widely used shell
process, and the term extrusion usually refers to c. Extrusion with lubrication without a shell
● Tooling
this process. The machinery used is usually
based on so-called standard designs. a. Container, stem, dummy block, and die
The other extrusion processes usually require
specially developed machines. They are de- The wide range of different designs for extru-
signed accordingly and built to meet the needs sion presses has recently been reduced in most
of the operator. extrusion plants to a few high-output types.
Therefore, only extrusion press designs that
6.1.1 Machinery for Direct Extrusion dominate today’s market are discussed in this
chapter. These are referred to as standard extru-
The design of a direct-extrusion press is de-
sion presses in Table 6.1.
termined by the following factors:
Direct-extrusion presses account for more
● Product than 95% of the total volume of all presses. The
a. Aluminum and aluminum alloys (light direct-extrusion press is used for all current ex-
metal) easy to extrude and/or difficult to trusion processes.
Machines for the direct hot extrusion of for the economic optimal production are al-
light-metal alloys are mainly used for the ex- ready considered to be standard.
trusion of section (80%), tube (10%), and rod
(10%) in aluminum and aluminum alloys.
The machines for direct hot extrusion of 6.1.1.1 Extrusion Press Design Principles
heavy metals, mainly copper and copper al- Initial discussions, over 50 years ago, to ra-
loys, are used for the extrusion of rod, wire, tionalize the construction of extrusion presses,
and section (60%) (mainly in brass) and tube resulted in the standardization of extrusion
(40%) (mainly in copper). tooling in (DIN 24540). Within the last 30
Steel and steel alloys are only produced by years, the press manufacturing companies have
extrusion to a limited extent, and then only introduced standardized designs onto the mar-
when rolling is not possible or the volumes are ket.
too small. Table 6.1 shows the features of extrusion
The following major points must be consid- presses for light metals, heavy metals, and
ered in the construction of extrusion presses: steel.
● Technology requirements: This covers the The main feature of the direct-extrusion
metallurgical aspects of the deformation press is the stationary container during extru-
technology of extrusion. The process tech- sion. The die, which is also stationary, and the
nology for the material being extruded has support tooling are located at one of the end
been discussed in detail in Chapter 3, “Rod faces of the container, in front of the container
and Tube Extrusion Processes.” bore. Opposite the die, the dummy block lo-
● Economic factors: The economic need for cated in front of the extrusion stem pushes the
rationalization in the construction of extru- billet through the container bore, and the sec-
sion presses is most clearly seen in alumi- tion emerges through the die (Fig. 6.1).
num extrusion. New extrusion plants are The geometric proportions for different de-
built as integrated production lines. They signs for direct extrusion are shown in Fig.
include billet stores, billet heating, extru- 6.2.
sion press, handling equipment with lon- The most common design of extrusion press
gitudinal and transverse conveyors, section today is the prestressed four-column press. It
cooling systems, stretcher, cut-to-length is usually built with a standard stroke, which
saws and stackers, as well as heat treatment provides good access and easy maintenance.
equipment and packing lines. Similar de- In a standard-stroke press, the billet is
velopments can be found in heavy-metal loaded between the container and the stem.
extrusion plants. Sophisticated systems for The press stroke is determined by the loading
electronic data collection and data analysis stroke and the extrusion stroke. There are no
Table 6.1 Presses for the direct extrusion of aluminum alloys (light metal), copper alloys (heavy
metal), and steel
Direct-extrusion presses(a)
Light metal Heavy metal Steel
Equipment Standard press Special press Standard press Special press Rare
Press
Discard shear I, II, III I, II, III, IV ... ... ...
Discard saw ... ... I, II I, II I, II
Press drive
Oil hydraulic drive up to 25 mm/s I, II, III I, II, III, IV ... ... ...
Oil hydraulic drive up to 60 mm/s ... ... I, II I, II ...
Water hydraulic drive up to 300 mm/s ... ... ... ... I, II
Manipulation systems
For fixed dummy blocks I, II, III I, II, III, IV ... I, II I, II
For loose dummy blocks without cleaning block ... I, II, III, IV ... ... ...
For loose dummy block and cleaning block ... ... I, II ... ...
For loose combination dummy and cleaning blocks ... ... ... I, II ...
(a) Product: wire, bar ⳱ I, section ⳱ II, hollow section ⳱ III, wide solid section ⳱ IV (rectangular container)
Chapter 6: Machinery and Equipment for Direct and Indirect Hot Extrusion / 325
specific requirements placed on the quality of be held exactly between the die and the stem
the billet geometry; it is not important for the on the press centerline. This ensures that the
billet loading. Over 95% of extrusion presses clearance between the billet and the container
in extrusion plants are standard-stroke presses. is as uniform as possible, guaranteeing perfect
Figure 6.3 shows a 75 MN aluminum extru- upsetting of the billet in the container.
sion press with extrusion tooling for the extru- The tolerance-related diameter variations
sion of round and flat billets. The moving must be compensated by the billet loader to
cross head has X-guiding similar to the con- ensure that the billet can be clamped on the
tainer holder. The control and information sys- press centerline (Fig. 6.5). This ensures that
tems to monitor and optimize the extrusion the upsetting of the billet takes place under
process can be seen in the foreground. optimal conditions because of the equal clear-
The short-stroke press is compact and re- ance on all sides to the container bore. Air
quires less space. The short stroke (approxi- inclusions are less critical, and transverse
mately 60% of the standard stroke) includes forces, even if acceptable to a small degree,
the extrusion stroke and a free stroke for ma- are avoided during upsetting.
nipulation. There are three different designs. Short-stroke extrusion presses have been the
The billet-loading requirements are either: state of the art for some time. There are vari-
ous reasons for this. Schloemann built two 125
● Billet loading with a billet loader in the MN rod-and-tube extrusion presses for alumi-
free space between the die and the con- num around approximately 1950. These were
tainer, with the billet clamped on the press manufactured as short-stroke presses for pro-
centerline (the most common design)
duction reasons, with billet loading between
● Free space by extrusion stem transverse
the die and the container. The stem transverse
movement on the moving cross head (billet
movement was used before the end of the last
loading with a billet loader between the
century. The length of expensive press com-
moving cross head and the container)
ponents, including columns and the main cyl-
[Bri 96]
● Three containers that can be rotated around
inder, can be kept to a minimum.
The company Loewy built a steel tube ex-
a column of the press frame (billet loading
trusion press in 1960, with three containers
without a billet loader in one of the three
that could be rotated around a column. The
containers outside the press)
aim was high-throughput extrusion with fast
Figure 6.4 shows the control desk, movable press cycles. In practice, this was unsuccessful.
auxiliary control desk (swinging), hot log shear The manipulation of the heavy heated contain-
with the billet loader, and the short-stroke ers was only possible with expensive technol-
press for aluminum alloys. The container is in ogy. Temperature variations within the con-
the extrusion position. The billet is loaded be- tainer holder as well as in adjacent press
tween the die and the stem when the container components could not be avoided during pro-
has moved back over the stem. The billet must duction. Accurate location of the rotating con-
tainers on the press centerline and in line with rotations of 120 within an extrusion cycle, re-
the stem and the die could not be guaranteed quired extensive maintenance and regular re-
to the necessary reproducibility. The continu- pair. Only a few presses were built to this de-
ous movement of the large containers, three sign and actually used for production. In
Fig. 6.2 Geometric relationships for different designs for direct extrusion
Chapter 6: Machinery and Equipment for Direct and Indirect Hot Extrusion / 327
general, short-stroke presses are more expen- ● Moving crosshead, consisting of stem
sive than standard-stroke presses because of holder, return cylinders, and, if necessary,
the manipulation needed for billet loading and advance cylinders
the mechanical design. ● Container holder with container-moving cyl-
inders
6.1.1.2 Main Subassemblies of the Direct- ● Die slide or short die carrier, rotating die car-
Extrusion Press rier, or stationary tool carrier acting as the
die holder
All extrusion presses consist of the following ● Discard shear and/or discard saw
main subassemblies:
The function of the press frame is to withstand
● Press frame, consisting of the following sub- the extrusion load. A prestressed stiff press
assemblies: frame provides:
a. Main cylinder: One or two piece; housing
● Low press extension
and main cylinder
● Low deflection of the die support [Stt 96]
b. Platen: One piece with or without a dis-
● Short decompression time
card shear and/or with a discard saw
c. Columns: Round columns with inboard The press frame consists of a cylinder housing
and external nuts, round columns with with the main cylinder and ram, a platen, and, if
compression sleeves (tubular) and exter- the four columns are not designed as tension and
nal nuts, lamellar tension elements with compression elements, a bed plate and guide.
compression members The elastic behavior of the press frame under
d. Bed plate: Standard with round columns production conditions is an important character-
Fig. 6.3 Standard stroke extrusion press. Location: Alusuisse in Chippis, Switzerland
328 / Extrusion, Second Edition
istic of the extrusion press. The stiffness of the stead of the inboard nuts, then this is referred to
machine influences the accuracy of the guiding as a fully prestressed press frame.
and the die support during extrusion. With prestressed columns designed so that the
In many respects, the quality of the press tension elements are more highly stressed and
frame plays an important role in the extrusion the compressive elements subjected to lower
process. The operational reliability must first be stresses, the elongation can be reduced to 50%
guaranteed. Failures in the column threads must or less of that of non-prestressed columns with
be avoided at all costs. The notch effect at the normal dimensions.
root of the thread can increase the normal stress For example, for a 35.5 MN rod-and-tube
by a significant factor. In practice, only the first press with a column length of 12 m and an ex-
threads can transfer the forces. This disadvan- trusion load of 30 MN, the elongation for a pre-
tage is avoided with hammer head lamellar col- stressed press frame is approximately 2.5 mm
umns. The geometry of the hammer head can be and approximately 5 mm for a non-prestressed
optimized by finite element analysis. In the area press frame. Figure 6.6 compares the load elon-
of the cylinder housing and the platen, prestress- gation diagrams for both tension and compres-
ing with round columns is carried out, using in- sion elements and columns with nuts for this
board and external nuts. There is no prestressing press frame.
between the housing and the platen, resulting in It is correct that larger column diameters re-
a relatively large elongation of the press during sult in a lower stress and thus reduce elongation
extrusion. If hollow compression members are of non-prestressed frames. However, from the
located between the housing and the platen in- machine design point of view, this approach
causes problems with the geometry and the The auxiliary loads of the extrusion press are
guiding system for the die carrier. There is lim- determined by the relevant functions. The ability
ited space around the housings with larger col- to remove a billet stuck in the container from the
umns, resulting in an increase in the press cross press (sticking billet) is one factor that must be
section and thus the size of the extrusion press. taken into account.
A bed plate is needed for the guideways of The tool carriers for the stem and container
the die carrier. The total extrusion load is pro- can be moved and are fitted with double-acting
duced by the main cylinder and, when fitted, by cylinders. The space-saving oil hydraulic dou-
the two advance cylinders. The forces needed ble-acting cylinder offers advantages for both
for the auxiliary operations, including billet access and press maintenance.
loading, ram return, container sealing, and strip- Usually, the die carrier and the tools for die
ping, and the resultant cycle times must be taken changing are fitted with rapid-locking systems.
into account in the design of the cylinders. Bayonet fittings, which enable the tool to be
The container sealing forces and the stripping locked or released by a simple partial rotation,
forces depend on the design of the tooling and have proved successful.
the extrusion technology as well as the discard The discard separators do not belong directly
thickness. The container stripping force for alu- to the extrusion press. Discard shears and/or dis-
minum extrusion is determined as follows: card saws are configured in the design of the
extrusion press to ensure the optimal operation.
FRⳮSt ⳱ D0 • p(lF Ⳮ lR) • sS (Eq. 6.1) The competition among press manufacturers
during the 1950s and 1960s resulted in extrusion
where FRⳮSt is the container stripping force, D0 presses that were simple to build, cost-effective,
is the container diameter, lR is the discard thick- and that met the demands of the aluminum in-
ness, lF is the dummy block land length, and sS dustry. This resulted in machines that had and
is the shear stress of the billet material (see Sec- still have identical main subassemblies through-
tion 3.1.1.4 in Chapter 3). out the world.
Fig. 6.5 Upsetting of a billet clamped on the press centerline (good), and upsetting of a billet resting in the container (poor)
330 / Extrusion, Second Edition
For reasons of quality and economy, modern ● Extrusion presses for copper alloys for the
extrusion press manufacture requires a machine production of wire and/or bar and section
design based on function specific subassemblies. Indirect extrusion presses and tube presses,
Extrusion presses of modular design can have which are similar to direct-extrusion presses in
common functional components and still be tai- the main components, are discussed in more de-
lored to specific applications, depending on the tail in sections 6.1.2 and 6.2.2.
product and the process. The press types de- The components of the extrusion press must
scribed can be configured for a specific appli- form a structural unit that ensures a systematic
cation in an extrusion plant by the addition or functionality and combination (Fig. 6.7). It must
removal of components, for example, a discard be possible to combine the modular units so that
saw instead of a discard shear. This also applies depending on the application of the press, the
to the power system (water or oil hydraulic). desired production can be guaranteed. Table 6.2
Some of the most important presses for direct gives a general overview to assist in the under-
extrusion are: standing of a rational modular system and en-
● Extrusion presses for aluminum extrusion compasses the modern extrusion press and its
for the production of bar, section, and hollow products, including wire, rod, section, hollow
sections sections, and flat sections.
Fig. 6.6 Load diagram of a prestressed and non-prestressed press frame at a load of 31.5 MN. g, platen; h, column; i, inboard nut;
j, outboard nut; k, tension element; l, compression element; m, cyclindar housing
Chapter 6: Machinery and Equipment for Direct and Indirect Hot Extrusion / 331
The examples shown can differ from each tion, including billet loading. The extrusion load
other in the arrangement of the subassemblies. is used as a defining parameter for all compo-
Combined direct- and indirect-extrusion presses nents. The press stroke determines the column
are known that have, for example, one shear for length according to the design of the press and
direct extrusion and one for indirect extrusion. not the cross section. A bed plate is not required
Table 6.3 gives the steps in press power of with a prestressed design. This design enables
modern extrusion presses. This range corre- X-guiding to be readily realized. Flat guiding
sponds (in bold type) to the standard range can also be provided by the inclusion of suitable
R10 (from the tool standard DIN 25540). The structural elements that have to be independent
intermediate sizes (standard type) occur more of the elastic behavior of the press frame. The
frequently in the United States than in Eu- symmetry of the press frame is very important
rope. for the elastic behavior of the press under the
The design of the press frame (Fig. 6.8) must extrusion load. A square column arrangement is
take into account the extrusion load, container preferred, because it simplifies the components
and tool changing, and freedom for manipula- and results in uniform stresses.
Fig. 6.7 Direct extrusion press for aluminum showing the components
Table 6.3 Standard force ratings of commercial possible, the container-moving cylinders are lo-
presses cated in the main cylinder housing.
Extrusion load Adjustable guide shoes are used to guide the
MN kip(a) container housing. The guide-ways are primarily
5 1100 determined by the container housing because it
6.3 1400
8 1800
houses the container, which is the largest tooling
10 2250 item. The container working temperature de-
12.5 2810 pends on the production. To achieve a positive
16 3600
18 4000 location in the container housing independent of
20 4500 the temperature, the container is located in the
22 5000 container housing by four keys. It is located vir-
25 5600
28 6300 tually without any play in both the cold and the
31.5 7080 hot condition.
35.5 8000
40 9000 In horizontal extrusion, the maximum tem-
50 11,200 perature occurs in the region of the container
63 14,000 housing at approximately 20% of the external
71 16,000
80 18,000 container diameter above the press centerline.
100 22,500 This is because the container housing, which is
125 28,100
also hot on the outside, induces an air current.
Bold type are standard range (RIO from DIN 25540). Standard type are inter-
mediate sizes more common in the United States. (a) Kip, 1000 1b force is This cools the bottom half more severely,
derived from MN, meganewton. whereas the upper part of the container housing
falls in the wind shadow of the chimney effect
and increases in temperature. Locating the ther-
The tool carrier moving crosshead (Fig. 6.9) mal center of the container housing requires the
provides the advance, extrusion, and return center of the container to be measured in both
strokes. It is moved by the two double-acting the cold and the hot condition. The difference
cylinders and the main cylinder and transfers the can exceed 5 mm on large extrusion presses.
load to the extrusion stem. Quick release sys- The guide-ways for the container housing are
tems are used to locate the extrusion stem. The arranged as a prism (half X-guiding) to maintain
moving crosshead is guided by adjustable guide the central location of the container within the
shoes on the press frame guides. Upper locating tightest limits possible at different operating
guide shoes are used to provide better alignment temperatures. In order to achieve better and re-
accuracy during the movement of the extrusion producible guiding, an upper guide is used that
stem (X-guiding). often extends the guiding to X-guiding. The lo-
The tool carrier container housing (Fig. 6.10) cation of the guide-ways with X-guiding should
can be moved by two double-acting cylinders. take into account the thermal center point to en-
To ensure that the working area is as open as sure that the container housing is free from play
as far as possible and is accurately located Flat guiding is also encountered, and this is
within the extrusion press, even with tempera- simpler to adjust but assumes constant thermal
ture variations. conditions in the container holder under produc-
tion conditions. If the production conditions do Various designs are used for the tool carrier
not require different working temperatures, then for the dies. Four different designs are usually
flat guiding is used. The geometry of the flat used (Fig. 6.11).
guiding requires a central guide at the bottom as Die shuffles are used almost exclusively to-
well as the supporting guides. day for aluminum alloy extrusion presses. Two
Top guides to improve the running and guid- die carriers are used with a changing table out-
ing reliability are used in a wide range of con- side the press (Fig. 6.12). The die shuffle can
figurations. be used, if necessary, as an auxiliary shear to
The container heating has a significant influ- cut the sections behind the die by using a larger
ence on the container housing. Induction and shear cylinder. The operating position must be
resistance heating affect the design of the con- adjustable. The design height of the die stack
tainer housing in different ways. In each case, must be held to tight tolerances to guarantee the
the internal space must be thermally insulated exact shear position for correct separation of the
to ensure that the container loses as little heat discard from the section.
as possible and to protect the housing from It is important to always locate the die stack
overheating. Resistance heating can be used in- in the same shear position; otherwise, material
stead of induction heating, and this requires in- can build up in the area of the die front face,
sulation from the body of the housing. It heats which results in problems.
the container from the outside. In this case, it Die slides are used for copper alloy extru-
is difficult to bring the temperature above sion presses. They have a die and an ejection
400 C. position for the discard, dummy block, shell,
Fig. 6.13 16 MN aluminum alloy press with auxiliary equipment. (Factory assembly Danieli Breda)
336 / Extrusion, Second Edition
Shell. If no shell that must be removed is formed loading of the billet into the container bore. This
in the liner, extrusion is carried out with a fixed is particularly important if a two-piece billet is
dummy block. Multipart fixed dummy blocks produced by the log shear. The billet is held by
are used for aluminum extrusion. The billets are jaws without clamping. The dimensions and
lubricated for the extrusion of the difficult cop- shape depend on the diameter of the billet or
per and brass alloys and steel. A shell does not whether a rectangular billet is used.
then form. Extrusion is then carried out using To ensure reliable automatic operation of the
the lubricated-without-a-shell process. In this extrusion plant, the front face of the fixed
case, a single-piece fixed dummy block is used dummy block or the billet on the end facing the
for expedience. dummy block must be lubricated. The sheared
A swinging or a linear billet loader is used. discard is removed in a controlled manner by a
The lubrication of the billets before loading is chute and a conveyor after every extrusion cy-
carried out with special systems. The handling cle. If the discard sticks to the shear blade or the
of the sawn or punched discard is carried out by die, it is removed by a knocker that is operated
means of a chute or a conveyor. The tooling re- after shearing.
quires special care, including cooling, cleaning, Auxiliary Equipment for Direct Extrusion
and lubrication, and special devices (including with a Shell and with a Separate Dummy
die rotation systems with corresponding service Block and Cleaning Block. This is always nec-
locations) are used. essary when a shell is formed in the container
The auxiliary equipment is therefore re- bore for quality reasons. If short billets are used
stricted to billet loader, discard removal, and, or if a good billet surface enables extrusion to
rarely, dummy block lubrication (in case no bil- be carried out with a thin shell, then a separate
let end face lubrication is provided) and a die combination dummy block and cleaning block
change system. is both possible and economic. A separate
Auxiliary Equipment for Direct Aluminum dummy block must be used for difficult-to-ex-
Extrusion (Extrusion without a Shell and with trude aluminum alloys. The cleaning block is
a Fixed Dummy Block). The development of used at alloy changes and with high-value ma-
the expanding fixed dummy block eliminated terials.
the need for the previously necessary circulation The extrusion press for copper alloys is fitted
of several dummy blocks. Two-piece billet load- with a separate dummy block and a separate
ers are used to load a standard-stroke press with cleaning block and leaves a shell in the container
a billet (Fig. 6.15). This enables reliable and fast bore after each extrusion. The auxiliary equip-
Fig. 6.15 (a) Two-part billet loader in the start position outside the press (billet-receiving position). (b) Two-part billet loader in the
center of the press during the loading of the container
338 / Extrusion, Second Edition
ment needed include a billet and dummy block ability are advantageous, these are offset by the
loader (which also loads the cleaning block), re- investment costs and the wear in the valves as
moval system for the discard, dummy and clean- well as the corrosion of the machine components
ing blocks as well as the shell, discard and shell and the high maintenance and repair costs.
separator with a recycling system for the dummy Water hydraulic drive is only used today
and cleaning block, die change system, and sys- when short-term, very large press powers are re-
tem for cleaning the tooling. quired for the deformation process. This is the
Auxiliary Equipment for Direct Copper Al- case for steel extrusion presses in which, for ex-
loy Extrusion with a Shell. A two-piece billet ample, a 1000 mm long billet must be extruded
loader is used here in the same way as with alu- within 3 seconds.
minum alloy extrusion. The operating sequence Figure 6.16 shows the schematic diagram of
differs from that for aluminum alloy extrusion a water hydraulic accumulator drive system for
in that it is necessary to operate with dummy a direct-extrusion press.
blocks, and cleaning blocks, because a shell is Figure 6.17 shows an example of a pressure-
formed in the container bore. demand diagram for the water hydraulic accu-
One of the loader arms of the billet loader is mulator drive system, shown schematically in
needed to load the cleaning block. A removal Fig. 6.16.
tool is used to remove the discard, dummy At an operating pressure of 315 bar (4.57 ksi),
block, shell, and cleaning block as a complete approximately 22,600 L/min (5970 gal/min) are
package, which is transferred to a separator. needed for a 35 MN press, that is, a drive power
First, the free-standing cleaning block is trans- of approximately 14,500 KW. A direct pumping
ferred to a block recycling system with maga- drive would be both economically and techni-
zine and, if necessary, a cooling station. Moni- cally unviable for such a high power. Because,
toring of the dummy block separation operation for example, the steel 35 MN extrusion press
by the operating personnel is necessary. Al- requires an extrusion time of 3 seconds, which
though intervention is not always required, is approximately 10% of the total operating cy-
problems can occur with uneven or torn shells. cle, a drive of approximately 1800 KW would
The shell is removed simultaneously with the be sufficient. The lower pump power can be ad-
separation of the discard from the dummy block, vantageously utilized with an accumulator.
which moves into the block recycling system. Even during the dead cycle, the pumps supply
The discard and shell finish up in the scrap con- pressurized water to the accumulator, where the
tainer via a chute and a conveyor. Because sev- required water volume is stored. These accu-
eral dummy and cleaning blocks are used, these mulator systems were used previously as central
are held in a magazine, ready for use. A distrib- power supplies for several presses. They are
utor supplies the dummy block on demand, and now occasionally found in large extrusion plants
it is always loaded together with a heated billet operating a large number of presses for alumi-
into a transfer system. At the end of extrusion, num and copper alloys.
the cleaning block is also loaded into the transfer The water hydraulic drive pumps for operat-
system. One of the billet loader arms moves the ing the presses are high-pressure pumps with
cleaning block into the center of the press in three or four pistons (Fig. 6.18). They have a
order to clean the shell from the container bore. constant delivery and operate at working pres-
sures between 200 and 315 bar (2.90 to 4.57
6.1.1.4 Hydraulic Drive and Control ksi). They are fitted with return and safety
valves. Reduction gears are necessary between
Systems for Direct Extrusion
the pumps and the electric motors to ensure a
When hydraulic presses were first built, the technically acceptable rotation speed, which
operating medium was exclusively water. Over should be less than 300 rpm. The low rotation
a period of time, emulsifying agents were added speed of the crankshaft is essential for the func-
to the water to protect the machine components tion and service life of the piston seals. If the
against corrosion. Oil hydraulic presses did not piston speed is too fast, the seals and pistons can
become popular until approximately 1950. To- overheat, reducing the functionality.
day, water hydraulic extrusion presses are rarely The overhead reservoir tank serves as a con-
seen in new plants. Although the reduced envi- tainer for the entire working medium (emulsified
ronmental impact, the absence of fire risk, and water). The unpressurized water is fed back here
the possibility of short-term high-energy avail- by the control valves and from the prefill tank.
Chapter 6: Machinery and Equipment for Direct and Indirect Hot Extrusion / 339
The high-pressure pumps and the filling pumps drop that can be allowed in an application
suck the emulsified water from the overhead res- must be verified. The accumulator station in-
ervoir tank. cludes high-pressure compressors for the air
The accumulator consists of a series of bottles, hydraulic controls that can be operated
high-pressure containers (high-pressure bot- by hand or electrically, safety and shut-off
tles) that are supplied with the emulsified valves for water and air, and optical as well
water and the compressed air. The high-pres- as acoustic safety devices.
sure pumps are switched on and off by the The prefill tank, which is also referred to
water level measured in the bottles by ultra- as an air reservoir, is a low-pressure container.
sonic probes. To avoid an unacceptably high It is used to move the ram during billet load-
pressure drop during the removal of the ing (standard-stroke press) and to move the
pressurized water, the ratio of the compressed mandrel forward on tube presses into pre-
air volume to the pressurized water volume pierced or bored billets. This saves pressur-
should be greater than 10 to 1. The pressure ized water. Prefill valves are needed with a
Fig. 6.16 Schematic arrangement of a water hydraulic accumulator drive system for an extrusion press
340 / Extrusion, Second Edition
prefill tank. The working pressure of the pre- systems are also common in oil hydraulic sys-
fill tank is between 8 and 16 bar. Decom- tems. In contrast to water, oil can be used as
pression shocks are largely avoided by taking the operating medium without packings and
the exhaust water from the hydraulic controls. thus without expensive seals, because of its
The hydraulic controls consist of manifolds viscosity and its lubrication effect, for the
with valves and connections for pressurized pump pistons of the high-pressure pumps and
water and exhaust water pipes. Depending on for the directional valves. Axial piston high-
the function, they are used as speed controls pressure pumps are relatively simple to adjust,
for different speeds, as the main control for so that variable deliveries are possible.
the press, or as control for the container Proportional and servo-valves can be used
movement, piercing system, and shear. They for controlled operations or control loops. The
are seated valves and operate as pressure wa-
components in oil hydraulic systems are sig-
ter inlet or outlet valves, as nonreturn valves,
nificantly cheaper than those used in water
decompression valves, and as safety valves.
They are fitted with throttle valve plugs or hydraulic systems. Mass production provides
throttle valve cages and can have a stacked both a lower cost and a high-quality standard.
multistage design to ensure a smooth connec- The drive pumps are axial piston pumps with
tion and disconnection from cylinders during constant and/or variable deliveries. Submerged
the press cycle. The valves are either operated pumps are placed directly in the oil tank. The
by oil hydraulic pilot valves or motor-driven working pressure ranges from 200 to 315 bar.
cams or by a lever system moved by hand or For economic reasons, a working pressure of
servo-cylinders. 250 bar (3.62 ksi) is preferred for extrusion
Oil Hydraulic. Water hydraulic systems presses. The power supply speed of rotation
have been displaced in press manufacture by is 1000 rpm for submerged pumps and 1500
oil hydraulics (Fig. 6.19). Today, accumulator rpm for prefilled pumps.
Some examples for the required operating separate high pressure pumps, the filter, the
power for different extrusion presses are: cooler, and the valves (Fig. 6.20, 6.21).
To reduce the noise level, the high-pressure
● 12.5 MN extrusion press for aluminum al- pumps are preferably installed as floor mounted
loys; 3 ⳯ 90 KW ⳱ 270 KW pumps in a cellar or a special pump room. The
● 35 MN rod-and-tube press for copper alloys; spatial needs for the hydraulic system are ad-
5 ⳯ 320 KW ⳱ 1600 KW vantageous with submerged pumps, because
● 35 MN indirect rod-and-tube press for alu- shorter pipe lengths can be used.
minum alloys; 5 ⳯ 200 KW Ⳮ 1 ⳯ 75 KW The controls in oil hydraulic systems can be
⳱ 1075 KW divided into high-pressure and low-pressure con-
trols. The high-pressure controls are arranged in
These examples show that the power of the function-specific manifold blocks similar to water
pumps relative to the extrusion press powers in- hydraulic systems. The various directional valves
creases in larger steps. This results in maximum are attached to the manifold blocks. Access must
extrusion speeds that often exceed the required be taken into account. The exhaust oil goes di-
values for the different press sizes. rectly from the manifold block back into the tank.
The oil tank is often located over the main The directional valves are controlled indirectly by
cylinder housing. It can hold the entire oil vol- electrically controlled pilot valves (solenoid
ume for the plant. It is connected as a nonpres- valves) that operate the large directional valves.
surized container directly to the main cylinder Mechanical control systems are not used, unlike
through a prefill valve. On the oil tank are the water hydraulic systems.
controls and, in the case of submerged pumps, Cartridge (seated) valves are being used more
the high-pressure pumps, the low-pressure and more instead of directional valves (slide
pumps with low-pressure accumulators, the aux- valves). As with water hydraulic systems, they
iliary pumps for the cooling and filter circuits, are installed in manifold blocks. The cartridges
the pilot pressure pumps, and, in the case of are hydraulically controlled by pilot valves.
The low-pressure control with an operating
pressure up to 100 bar (1.45 ksi) is arranged in
stacked elements, either as a central control sys-
tem in an easily maintained location or in the
immediate vicinity of the cylinders, high-pres-
sure variable delivery pumps, or high pressure
controls. The low-pressure control consists of
directional valves, and proportional and/or servo
valves, depending on the application.
The low-pressure control is used for:
● Hydraulic pilot control of the high-pressure
directional valves
● Control of the auxiliary systems (billet load-
ing, discard removal, tool recycling)
● Control of additional systems (saw, lubrica-
tion, cooling, etc.)
● Control of pumps and cylinders
● Control of the press-handling system
extrusion plant. A plant is only economic to- Additional electrical drives are needed for the
day if it has a data processing system as well handling system.
as automatic control. Direct current or frequency-controlled three-
The electrical drive system belongs to the phase motors are used for coilers and for extru-
power part of the electrical control system. The sion puller systems. The power requirements of
oil hydraulic high-pressure pumps are usually these machines fall between 20 and 80 KW. The
driven by three-phase motors (up to approxi- cut-off saws in the run-out system require be-
mately 300 KW). For example, a 50 MN extru- tween 5 and 40 KW, depending on the material
sion press for copper alloys requires six motors, and the cross section.
each of 320 KW, or eight motors of 250 KW. Electric heating is needed in hot working for
Approximately 85% of an installed total power the extrusion press container. Independent of the
of 2300 KW is needed for the high-pressure material being extruded, controllable resistance
pumps. Apart from the low-pressure pumps and and/or induction heating is used. Induction heat-
those for the auxiliary, there are no larger elec- ing of the container is often seen today. Resis-
trical drive systems around the extrusion plant. tance heating is now preferred for new plants. In
Fig. 6.19 Schematic arrangement of an oil hydraulic drive system for an extrusion press
Chapter 6: Machinery and Equipment for Direct and Indirect Hot Extrusion / 343
contrast to induction heating, it can be designed surface and the insulation of the container. The
so that it is possible to adjust the container tem- required heating power ranges from 30 to 200
perature over the length of the container. The KW, depending on the press size and type of
heating power depends initially on the required construction.
operating temperature in the container (500 C The electrical control system is a program-
for aluminum alloys and approximately 400 C mable logic control (PLC) system. It can be
for copper alloys) as well as on the container readily programmed and thus includes many
Fig. 6.20 Oil hydraulic drive system with controls, tank, filters, coolers, and valves
possibilities for the optimization of the operating and the stem and container move in the
sequences [Iwa 84]. It is therefore possible at working direction. Or stem outside the
any time to monitor the operational conditions press centerline (Fig. 6.2) container in the
and possible faults as well as to transfer proto- extrusion position, billet loading between
cols and data via a centralized computer. An op- the container and the moving crosshead,
erating control system for the extrusion process the billet is pushed with a special device
can also be included. Orders can be controlled, into the container bore, stem on the mov-
processed, and monitored [Bug 88]. ing crosshead from the side position to the
Different manufacturers of the PLC can be extrusion position. Or container rotating
used for the control units that are arranged in on an extrusion press column or cross
independent blocks for the furnace line, the ex- slide, stem in starting position, billet load-
trusion plant, and the handling system. In many ing in the container outside the press with
cases, they are specified by the plant for internal a special device, container from the side
reasons (experience, existing systems). Special position into the extrusion position.
systems have been developed for the extrusion 2. Extrusion: The main operation after the billet
process, including: is in the extrusion position consists of upset,
initiation of the extrusion process, and when
● Process monitoring with fault diagnostics the preset discard length has reached decom-
and visible production sequence on a com- pression.
puter screen 3. Clearing: The tooling is opened, the extruded
● Storage of production and operational data section is separated from the discard and
and material flow in the manufacturing pro- transported away, the discard and, if present,
cess the shell are removed, and the tooling is
● Control of container temperature over the moved to the starting position.
container length 4. Tool preparation: Depending on the material
● Billet temperature over the billet length and being deformed, the tooling is cooled,
ram speed over the ram displacement, with cleaned, lubricated, and changed if required.
the aim of a constant exit temperature over
Operating Sequence Direct Extrusion. The
the ram stroke or over the length of the ex-
times in the operating sequence described as fol-
trusion
lows apply to a medium-sized extrusion press
(20 to 35 MN). They take into account the most
6.1.1.6 Typical Operating Sequence for important operating sequences, sometimes in a
Direct Extrusion summarized format.
Four main operations characterize the proce- The sequential times have not been adjusted
dures in extrusion: for maximum speed but more to operational and
economically viable values that can be achieved
1. Loading: The hot billet must be brought into during the operation of an extrusion press with-
the press. This is carried out by a billet loader. out risks of breakdown.
The design depends on the construction of Tool change times, program changes, break-
the press. For example: downs, and continuous maintenance can sig-
a. Standard stroke, corresponding to the nificantly reduce the productivity during an
overview of types of long-stroke extrusion extended production period. The annual
press (Fig. 6.2). Stem in the starting po- throughput can be reduced to approximately
sition, container in the extrusion position, 70%.
billet loading between the stem and the Table 6.5 shows the working cycle for an alu-
container, the billet is pushed by the stem minum alloy press for easy and moderately dif-
into the container bore, and the stem ficult-to-extrude alloys with a standard stroke
moves in the working direction. and fixed dummy block. The operating steps are
b. Short stroke, corresponding to the over- shown in Fig. 6.22. The working cycle and the
view of types of short-stroke extrusion operating steps for a short-stroke press are
press (Fig. 6.2). Stem on the press center- shown in Table 6.6 and Fig. 6.23.
line in the starting position, container over
the stem, billet loading between the stem/ 6.1.2 Machines for Indirect Extrusion
container and the die. The billet is In the past, extrusion presses for indirect ex-
clamped between the stem and the die, trusion were installed in only a few locations.
Chapter 6: Machinery and Equipment for Direct and Indirect Hot Extrusion / 345
They were used for the production of brass wire. ate with varying degrees of success (Fig. 6.24).
Production plants for indirect extrusion are now A tendency for high-throughput machines can
seen more frequently. The high demands on be seen in brass wire and rod indirect-extrusion
quality and productivity have resulted in the de- presses. High-value products can be produced in
velopment of indirect-extrusion plants [Yok 77]. difficult-to-extrude aluminum alloys on indirect-
New indirect-extrusion press plants for the pro- extrusion presses. The extrusion presses de-
duction of brass wire and rod operate with high scribed as follows only cover designs with sig-
economic success. The moderately difficult and nificant output. These are classified as standard
the difficult-to-extrude aluminum alloys are not in Table 6.7.
processed to any significant degree on indirect- The points made in the section about ma-
extrusion presses. In contrast, indirect tube ex- chines for direct extrusion must be covered in
trusion for aluminum alloys is used to a signifi- the design of indirect-extrusion presses.
cant extent. The characteristic feature of indirect-extru-
The design of an indirect-extrusion press is
sion presses (including indirect rod-and-tube
determined by the following factors:
presses even though these have only been pro-
● Product
duced to a limited extent) is the container linked
a. Difficult-to-extrude aluminum and alu- to the moving crosshead during extrusion. With
minum alloys, rod, and section copper alloys, the moving crosshead usually has
b. Brass—easy to extrude and/or difficult to
a sealing tool, and the press has a standard
extrude (wire, rod, and section). Steel and
copper are not extruded by the indirect stroke.
process. With aluminum alloys, the short-stroke press
● Process technology (Fig. 6.25) is preferred [Asa 84]. A sealing stem
a. Indirect extrusion without lubrication and is used. The advantage of this sealing stem is:
without a shell ● Reliable billet loading of all billet lengths
b. Indirect extrusion without lubrication and without the billet jamming
with a shell ● Possible for a sticking billet to be pushed out
6.1.2.1 Press Design with the press power into a discard carrier
Today, there are a large number of different In all indirect-extrusion presses, the stationary
designs for indirect-extrusion presses that oper- die is located at the front face of the extrusion
Table 6.5 Operating sequence of an extrusion press for easy and moderately difficult-to-extrude
aluminum alloys with standard stroke and fixed dummy block
Operating Time sequence in seconds: Comments
stage 5 10 15 20
1 Billet loader in Billet loading
2 Extrusion stem Billet pushed against
advance die
3 Billet loader Loading position /
out starting position
4 Extrusion stem Upsetting,
advance and decompression / air
return removal
5 Extrusion stem Upsetting, extrusion
extrusion
6 Decompression Press under no
pressure
7 Container strip Discard clear, shear
position
8 Extrusion stem Starting position
return
9 Discard shear Discard removal
monitoring
10 Container Press in starting
moves to die position
346 / Extrusion, Second Edition
stem located on the platen. The die block located sions. Apart from this, the tooling differs only
in front of the hollow stem enters the container in its application for a specific production, as
bore during extrusion. The billet is then extruded discussed previously for direct extrusion. The
to the discard length without any relative move- design for the indirect-extrusion press must al-
ment between the billet and the liner (i.e., with- low for the container movement over the press
out friction), in contrast to direct extrusion. stroke plus clearance for other operations; also,
The tooling is similar in design and structural the press stem is located on the platen, with the
details to direct extrusion and is based on DIN discard being removed between the moving
24540. The tool set of the die block is relatively crosshead and the container. If a sealing tool is
small and multipiece for copper alloys and both used and the billet is loaded between the con-
multipiece and single piece for aluminum alloys. tainer and the extrusion stem, the press must be
The external diameter is limited by the container designed as a standard-stroke press. The short-
bore. The maximum cross-sectional area of the stroke press is used:
extruded profile is determined by the largest pos- ● When the billet is loaded between the sealing
sible stem bore and is significantly limited, in tool and the container, and the billet is
contrast to sections produced by direct extru- clamped
● When a press with a sealing stem is used, sired level in all areas. The shell frequently pre-
and billet loading takes place between the vents full automatic operation of an extrusion
container and the sealing stem plant. A relatively thin shell is produced in in-
direct extrusion.
6.1.2.2 Main Structural Components of The transfer of the extruded section to the run-
Indirect-Extrusion Presses out system occurs after separation from the dis-
As in section 6.1.1.2, a typical design is de- card, similar to direct extrusion. The auxiliary
scribed here (Fig. 6.26, Table 6.8). Note: The equipment required for indirect extrusion de-
examples given may differ in the arrangement pends to a large extent on whether copper alloys
of the main subassemblies. Combination direct- or aluminum alloys are being extruded and
and indirect-extrusion presses are known that whether a fixed or a loose die block is used.
have, for example, a shear for direct extrusion The auxiliary equipment systems used in the
most common indirect-extrusion plants are de-
and a shear for indirect extrusion. The main sub-
scribed in the following sections.
assemblies are almost identical for direct and in-
Auxiliary Equipment for the Indirect Ex-
direct extrusion. The modular units already de-
trusion of Aluminum Alloys. The short-stroke
scribed enable all current press designs to be
press with two stems (extrusion stem and sealing
produced.
stem) is the most common for indirect aluminum
6.1.2.3 Auxiliary Equipment for alloy extrusion. The auxiliary equipment is de-
signed accordingly. Because in indirect extru-
Indirect Extrusion
sion the container moves over the billet during
Similar to that of direct-extrusion presses, the billet loading, the pivoting billet loader is mov-
auxiliary equipment associated with indirect-ex- able in the direction of extrusion. Without open-
trusion presses is necessary for a more or less ing the billet clamps, it withdraws over the seal-
automatic press operation. The development of ing stem as the container moves over the billet.
the auxiliary equipment for automatically oper- This loading process ensures reliable and effi-
ating extrusion plants has not reached the de- cient billet loading between the sealing stem and
Table 6.6 Operating sequence of an extrusion press for easy and moderately difficult-to-extrude
alloys with a short stroke and a fixed pad
Half-seconds have been rounded up to the next highest value.
the container. In order to produce high-value ex- Sealing Tool). On a standard-stroke press with
truded products, a loose die block is used, which a sealing tool, the pivoting billet loader that
cuts a thin shell in the container bore during ex- moves in the extrusion direction is functionally
trusion (Fig. 6.27). The die block is fitted with the same as the billet loader described for indi-
recesses to receive the shell. The die block is rect aluminum alloy extrusion (Fig. 6.28). It
loaded with a special loader that loads it between withdraws over the shaft of the extrusion stem
the extrusion stem and the container. At the end without the billet clamp opening as the container
of the extrusion process, the discard and the die moves over the billet. Although extrusion is car-
block with the shell are pushed into a removal ried out without lubrication, as is the case in
tool. The discard is then sheared and the removal direct extrusion with a shell, there are differ-
tool swung from the press center into the transfer ences in the operating sequences for the auxil-
position. The sheared discard is transferred to a
iary equipment. The discard is sheared in front
scrap container via a chute and a conveyor.
of the die in the same manner as in indirect and
The die block with the shell is transferred
from the removal tool into a transporter that first direct extrusion of aluminum. After the shearing
moves to a shell separator to remove the shell process and the subsequent stripping from the
and to lubricate the shell recess. The die block container bore, a removal tool collects the
is then moved to the pivoting loader. A changing packet consisting of the die block, shell, and
and maintenance station is used, depending on cleaning block and transfers it to a working table
the program, and, if required, a heated holding adjacent to the press. An operator then must
station. transfer by hand the cleaning block to the block
Auxiliary Equipment for Indirect Extrusion recycling system and the die block first to the
of Copper Alloys (Standard-Stroke Press with shell separator and then to the recycling system.
Fig. 6.23 Operating steps in aluminum extrusion with a short stroke, time dependent
Chapter 6: Machinery and Equipment for Direct and Indirect Hot Extrusion / 349
The shell must be removed in the same way as realized in the area of separation devices be-
the discard, via a chute and a conveyor. The die cause of the shell formed from the use of
block and the cleaning block are loaded with a dummy blocks or die blocks as well as clean-
pivoting loader. ing blocks. Manual operations are still neces-
The development of automatic auxiliary sys- sary, even if only sporadically. The auxiliary
tems for copper alloy extrusion has not been equipment described as follows depicts an in-
Table 6.7 Equipment for indirect extrusion with equipment for the different operations
Indirect extrusion(a)
Light metal Heavy Metal
Equipment Special Case Standard Special case
Press
Discard shear I, II I I, II
Saw ... ... I, II
Press drive
Oil hydraulic drive to 25 mm/s I, II ... ...
Oil hydraulic drive to 60 mm/s ... I I, II
Manipulation systems
For fixed-die block I, II ... ...
For loose die and loose cleaning block ... I I, II
For loose combination die and cleaning block I, II ... I, II
(a) Product: wire, bar ⳱ I; section ⳱ II
350 / Extrusion, Second Edition
teresting approach to solving the shell prob- press center so that a single-piece billet loader
lem. with a swinging loading head (in contrast to the
Auxiliary Equipment for the Indirect Ex- two-part pivoting billet loader) can be used. This
trusion of Copper Alloys with an Extrusion method of billet loading requires accurate cen-
and a Cleaning Stem. The short-stroke press is tral location of the clamped billet. The container
equipped with a tool slide that carries the extru- is positioned over the cleaning stem with a fixed
sion stem and the cleaning stem. The sealing tool cleaning block. While the billet is clamped be-
contains a ram to clamp the billet loaded into the tween the ram and the cleaning block, the con-
tainer moves over the billet to clear the space stem and finishes in a scrap bin, along with the
for the extrusion stem with the die block. discard, via a chute and a conveyor. The removal
After extrusion and the shearing of the discard tool passes the die block into a recycling system
in front of the container bore, the die block is where, if necessary, die changing, cooling,
pushed into a removal tool. The shell remaining cleaning, and lubrication are possible. A loader
in the container bore is cleared by the cleaning transfers the prepared die block for a new extru-
Table 6.8 Presses for indirect extrusion of aluminum (light metal) and copper alloys (heavy metal)
Indirect-extrusion presses(a)
Structural components Light metal Heavy metal
Main subassemblies Subassemblies Standard press Special press Standard press Special press
Press frame Cylinder housing I, II ... I, II ...
Platen I, II ... I, II ...
Columns I, II ... I, II ...
Bed plate ... I, II ... I, II
Moving crosshead Moving crosshead I, II ... I, II ...
Advance-return cylinder I, II ... I, II ...
Container holder with shear Container holder I, II ... I, II ...
Moving cylinder I, II ... I, II ...
Shear I, II ... ... ...
Die carrier Die slide ... I, II I, II ...
Die shuffle ... I, II ... I, II
Die rotating arm ... ... ... ...
Stationary die holder I, II ... ... I, II
Extruded product separator Shear I, II ... I, II ...
Saw ... ... ... ...
(a) Product: wire, bar ⳱ I; section ⳱ II
Fig. 6.27 Auxiliary equipment for the loose die block of an indirect aluminium alloy extrusion. (a) Discard shearing in collector.
(b) Die block, loader, and transporter. (c) Shell separation in operation; transporter with die block. (d) Die block changer
in operation. (e) Change and maintenance station, heat retention station, and transporter
352 / Extrusion, Second Edition
8 Discard Extrusion
shear cut from
discard
and cleared
9 Container Loading
back position
for cleaning
block
10 Loader in Cleaning
block
loaded
11 Shell Moving
removal crosshead
advance,
shell
compacted
12 Moving Clearance
crosshead for
return remova l
tool
13 Removal Removal
tool in of block
and shell
14 Container Removal
and removal via
tool advance extrusion
stem
15 Removal To
tool out transfer
position to
auxiliary
equipment
16 Container + Press in
moving loading
crosshead position
return
Chapter 6: Machinery and Equipment for Direct and Indirect Hot Extrusion / 355
Fig. 6.29 Operating steps in the indirect extrusion of brass. See Table 6.9.
356 / Extrusion, Second Edition
f. Tube extrusion over a moving mandrel seamless hollow sections that cannot be pro-
without lubrication and with a shell duced with a welding chamber die. Products
● Tooling: Container, stem, mandrel, dummy produced by rod extrusion presses can also be
block, and die produced with tube extrusion presses. How-
ever, in this case, the machines must be
The products described apply to presses that matched and specified to the required produc-
extrude only seamless tubes and sometimes tion range.
Table 6.10 Presses for the direct tube extrusion of aluminum (light metal,), copper (heavy metal),
and steel
Direct tube extrusion press(a)
Light metal Heavy metal Steel
Equipment Standard press Special press Standard press Special press Standard press Special press
Press
Discard shear I, II ... ... ... ... ...
Separating saw ... I, II I, II ... I, II ...
Container length, standard I, II ... I, II ... I, II ...
Container length, short ... ... I ... I ...
Piercing system(b) I, II ... I, II ... I, II ...
Mandrel movement(c) ... ... ... ... I, II ...
Mandrel internal cooling ... ... I, II ... ... ...
Press device
Oil hydraulic drive up to 25 mm/s(d) I, II ... ... ... ... ...
Oil hydraulic drive up to 60 mm/s(d) ... ... I, II ... ... ...
Water hydraulic drive up to 150 mm/s(e) ... ... ... I I, II ...
Water hydraulic drive up to 300 mm/s(e) ... ... ... ... I ...
Manipulation systems
For fixed dummy block ... I ... ... I, II ...
For loose dummy block without cleaning block I, II ... ... ... ... I, II
For loose dummy block and cleaning block ... ... I, II ... ... ...
For loose combination dummy and cleaning block ... ... ... I ... ...
(a) Product: tube ⳱ I; hollow section ⳱ II. (b) With mandrel stroke limitation and mandrel rotate. (c) With hollow billets. (d) Direct pump drive. (e) Accumulator
necessary
Chapter 6: Machinery and Equipment for Direct and Indirect Hot Extrusion / 357
Fig. 6.31 Direct tube extrusion tooling. Source: Schmidt & Clemans
358 / Extrusion, Second Edition
● Mandrel-moving system as mandrel carrier e. Discard shear and/or cut-off saw (main
consisting of: structural component extrusion press).
a. Mover crosshead
b. Mover cylinder with return Basically, the designs of tube extrusion
c. Container holder (main structural group presses can be classified into:
extrusion press)
d. Tool slide or carrier or rotating arm or ● Tube extrusion presses for aluminum alloys
stationary (main subassembly extrusion for the production of tubes and hollow sec-
press) tions
Fig. 6.33 Operating sequence of a direct tube extrusion press, time related. See Table 6.12 (in the table, times have been rounded
to 2 s).
Chapter 6: Machinery and Equipment for Direct and Indirect Hot Extrusion / 361
● Tube extrusion presses for copper alloys for piercer crosshead with a mandrel-holder carrier
the extrusion of tubes and hollow sections for the mandrel holder must be present. If re-
● Tube extrusion presses for steel for the pro- quired, internal cooling and/or mechanical or
duction of tubes and hollow sections hydraulic mandrel stroke limitation that is used
for the extrusion of tubes over a stationary man-
Depending on the application of the tube ex- drel or over the mandrel tip can be installed. The
trusion press, the modules must be capable of different functions of the piercing system for
being assembled in such a way that the desired tube extrusion depend on the material and the
production is guaranteed. Table 6.11 shows an process.
overview to help clarify a rational modular sys- The following factors influence the design of
tem. It does not contain all possible combina- the press:
tions but does take into account current tube ex-
trusion presses for aluminum alloys, copper ● The piercing load and mandrel return load—
alloys, and steel alloys (including nickel alloys). different for aluminum and copper alloy ex-
The examples mentioned can differ from each trusion
other in the arrangement of the subassemblies. ● Mandrel internal cooling—necessary for
Direct-extrusion presses are known that process copper alloys to improve the mandrel life
copper alloys, iron alloys, and nickel alloys. ● Mandrel stroke limitation for tube extrusion
The piercing and the piercer return cylinder over a stationary mandrel or over a mandrel
loads must be sufficient for piercing, mandrel tip (positioned mechanically or hydrauli-
return, and overcoming the billet friction on the cally)—necessary for aluminum and copper
mandrel during extrusion and during the auxil- alloys
iary movements (container and moving cross- ● Mandrel rotate system—required for rapid
head). mandrel changing and for positioning of a
The frictional forces on the mandrel depend profiled mandrel for hollow sections
on the material being extruded and the process ● Relative stroke of the mandrel during extru-
technology, that is, whether a stationary or a sion—useful to improve the service life of
moving mandrel is used. The forces on the man- the mandrel in the extrusion of copper alloy
drel can be very high with aluminum alloys. The tubes
maximum tensile force on the mandrel during
extrusion can be calculated from: 6.2.1.3 Auxiliary Equipment for
Direct Extrusion
FD ⳱ DD • p • l0 • sS (Eq. 6.2)
The auxiliary equipment for direct tube extru-
sion is similar to that used for direct rod extru-
where FD is the tensile load on the mandrel, DD sion. Mandrel lubrication is the only addition
is the mandrel diameter, l0 is the upset billet that may be necessary.
length, and sS is the critical shear stress of the
material being extruded.
To protect the mandrel from overloading, a 6.2.1.4 Hydraulic Control Systems
safety system must be provided to control the The hydraulic drive, control, and additional
resultant tensile forces. The container must re- equipment for direct tube extrusion correspond
main in its sealing position during piercing. The to that for direct rod extrusion. An additional
friction between the billet and the container hydraulic control is needed for the piercer sys-
should not displace the container as the billet tem. If the mandrel stroke limitation is hydrau-
expands. The mandrel return force must be set lic, an accurately operating control must be in-
to enable the mandrel to be withdrawn from a cluded for precise location of the mandrel in the
pierced or sticking billet. die. It must provide a stable location of the man-
The moving crosshead for tube extrusion drel during extrusion.
presses is designed to accommodate the piercing
system in a frame construction. The piercing 6.2.1.5 Electrical Drive, Controls,
system consists of a piercing cylinder and two and Additional Equipment for
return cylinders. A differential cylinder that acts
Direct Tube Extrusion
as the piercing cylinder is an alternative, pro-
vided that the required mandrel return force al- No additional equipment is required in the ar-
lows this system to be used. In addition, a eas of drive and heating electrical systems for
362 / Extrusion, Second Edition
Table 6.13 Equipment for indirect tube space for the billet as it increases in length
extrusion plants during piercing.
Indirect tube press(a) 3. Tube extrusion
Light metal 4. Clearing
Standard Special 5. Tooling preparation
Equipment press press
Press The operating sequence described in Table
Discard shear I, II ... 6.12 and Fig. 6.33 applies for the times required
Saw ... I, II for a medium-sized extrusion press (20 to 35
Piercing system(b) I, II ... MN). It takes into account the most important
Press drive operating sequences, to some extent, in a sum-
Direct oil hydraulic drive up to 25 mm/s I, II ... marized format.
Manipulation systems
For fixed-die block ... I, II 6.2.2 Indirect Tube Extrusion
For loose, combination die and cleaning block I, II ...
(a) Product: Seamless tube ⳱ I; seamless hollow section ⳱ II. (b) With mandrel
stroke limitation and mandrel rotation 6.2.2.1 Machine Design Details
The indirect tube extrusion press contains a
piercing system or a mandrel-moving system
the electrical drive and controls. The hydraulic similar in design and function to that in direct
and the electrical control systems must be ex- extrusion [Zil 84]. Until now, only a few indirect
panded to meet the requirements of the addi- tube extrusion presses have been built for diffi-
tional components needed for the tube extrusion cult-to-extrude aluminum alloys. Although com-
press. bined direct and indirect rod-and-tube extrusion
presses have been built for copper-base alloys,
6.2.1.6 Typical Operating Sequence for there is no significant tube extrusion of copper
alloys by the indirect tube extrusion process.
Direct Tube Extrusion
The design of indirect tube extrusion presses is
Five main operations characterize the tube ex- based on:
trusion operation:
● Product:
1. Loading a. Tube and hollow sections in difficult-to-
2. Piercing with a mandrel. The piercing system deform aluminum alloys
is used. The loaded billet is first upset in the ● Process technology:
container to center it. The stem with the b. Tube extrusion over a stationary mandrel
dummy block is withdrawn to leave an empty without lubrication with a shell
Table 6.15 Operating sequence of an indirect aluminum alloy tube extrusion press with two stems
for difficult-to-extrude aluminum alloys
Operational Time in seconds Comments
stage 4 8 12 16 20 24 28 32 36 40 44 48
1 Billet loader in Billet +
sealing block
loading
2 Container back Billet +
sealing block
in container
3 Billet loader Loading
out position /
starting
position
4 Die loader in Die block
loading
5 Moving Die block in
crosshead container
advance
6 Container Die loader
advance moves away
7 Die loader out Loading
position /
starting
position
8 Mandrel Up to die
advance position
(extrusion
position)
9 Container + Upsetting,
moving pressure
crosshead build up +
advance extrusion
10 Decompression Press
decom-
pressed
11 Mandrel back To starting
position
12 Moving Clearance for
crosshead back removal tool
13 Removal tool Removal of
in discard +
sealing tool
Fig. 6.34 Operating sequence for indirect aluminum tube extrusion, time dependent. See Table 6.15
Chapter 6: Machinery and Equipment for Direct and Indirect Hot Extrusion / 365
6.2.2.3 Typical Operating Sequence for depth, d (Fig. 6.35). This defines the thickness
Indirect Tube Extrusion of the peripheral layer in which approximately
87% of the energy transferred to the billet is con-
The operating sequence shown here has verted to heat. The thickness of this peripheral
proved suitable in many applications. However, layer, which depends on the electrical and mag-
for quality reasons, prebored fully machined bil- netic material properties of the billet as well as
lets are used. They are not pierced in the press! the frequency of the power supply, is approxi-
mately 70 mm for steel, 20 mm for copper, 30
mm for brass, and 25 mm for aluminum at their
extrusion temperature.
The heat transfers by conduction into the core
Billet Heating Systems region from the peripheral layer in the billet,
where the induced current flow causes heating.
Josef Putz* There is thus a temperature difference between
the billet periphery and the billet core that de-
Today, billets are usually heated to the desired velops from zero to a specific value and remains
operating temperature in main frequency induc- practically constant up to the end of the heating
tion or rapid-heating gas-fired furnaces. These of the peripheral layer (Fig. 6.36). The magni-
two furnace types are used because they are best tude of this temperature difference depends on
suited to meet the requirements of temperature the thermal conductivity of the material and on
control, flexibility, floor space, and so on of a the diameter of the billet as well as the specific
billet-heating furnace in a modern extrusion energy input. Because the peripheral layer is
plant. However, specific requirements often can- uniformly heated around the periphery, the heat
not be fulfilled by the standard designs of these flow to the core is uniform in all directions, and
furnaces, for example, extremely high through- the isotherms can be represented as concentric
puts, axial temperature distribution, and so on. circles.
Changes in the plant must be carried out or ad- This radial temperature difference in the billet
ditional equipment provided. at the end of the heating process is too large in
many cases to enable the billet to be immedi-
ately extruded, and therefore, it must be equal-
6.3 Induction Furnaces ized to a value suitable for extrusion. Naturally,
the time needed depends on the material and di-
6.3.1 General ameter of the billet as well as on the energy in-
In the induction furnace, the heat is produced put, because this parameter significantly affects
uniformly within the billet in a layer over the the developed temperature difference. In order
full circumference, referred to as the penetration to retain the peripheral layer at the final tem-
perature, the heat flow to the core in the tem- If the coil extension is below the optimum,
perature equalization is continuously replaced the field is weakened, resulting in a lower tem-
by the input of a corresponding energy amount. perature at the end of the billet. The reverse ef-
The electromagnetic field lines run parallel to fect occurs if the optimal coil extension is ex-
the billet axis in the middle of the billet (relative ceeded. This produces a field concentration and
to the length) within the directly heated periph- thus overheating at the billet end relative to the
eral layer of thickness, d. At the end of the billet, billet central region.
the field lines can be subjected to a change in
direction toward the billet edge or the billet core,
6.3.1.1 Single-Billet Furnace
depending on the size of the extension of the coil
over the end of the billet (Fig. 6.37). Only a The basic form of the induction furnace is the
specific extension length of the coil guarantees single-billet furnace, which, as the name sug-
a homogeneous field and temperature profile gests, is designed to heat a single billet. The sim-
over the billet length. This optimal coil exten- plest furnace design is when only a single billet
sion varies with the billet material and the billet length is processed, because the coil length can
diameter as well as the energy input. then be exactly matched to the billet length, tak-
Fig. 6.37 Distribution in the electromagnetic field line in the induction coil
Chapter 6: Machinery and Equipment for Direct and Indirect Hot Extrusion / 367
ing into account the optimal conditions. If the The single-billet induction furnace would def-
billet length changes, additional equipment is initely be the ideal heating system to meet the
needed to obtain uniform heating over the billet high specifications of an extrusion plant for the
length. The uniform heating is achieved at the billet heater if it did not have the disadvan-
billet end when the location of the billet in the tage of a low throughput. Only a relatively low
coil is designed to always produce the optimal throughput can be achieved with a single-billet
coil extension. The necessary additional equip- furnace, even with the maximum billet length.
ment is only provided at the one coil end, and In addition, the throughput drops even further if
this is, for expediency, selected to be the billet the billet length is reduced. The furnace can only
charging end. heat the same number of billets in a given time,
These additional systems serve to match the regardless whether the billets are long or short.
coil length to the billet length. This is carried out In almost all cases, several single-billet furnaces
as shown in Fig. 6.38, with the aid of tappings must be installed to achieve the desired through-
on the coil. However, the only billet lengths that put.
can be covered, taking into account the optimal
projection, are those that can be correlated by a 6.3.1.2 Multibillet Furnaces
tapping to a defined partial coil length. These
tappings only provide an approximate matching The multibillet induction furnace is the most
for continually varying billet lengths. widely used design and can, without doubt, be
The fine matching takes place by influencing considered as the standard configuration for in-
the electromagnetic field configuration, using a duction billet furnaces. As the name suggests,
so-called field extender. This field extender these furnaces contain several billets (Fig. 6.39)
works by homogeneously extending the electro- that are pushed, one by one, in billet-length steps
magnetic field from the billet so that a uniform through the furnace. In other words, when one
temperature profile up to the end of the billet is billet is pushed into the furnace, one billet must
ensured. The single-billet furnace with these ad- be removed from the exit. If the billet length is
ditional systems enables the optimal axial tem- changed, then, by necessity, the coil extension,
perature uniformity to be achieved. The heating
temperature can also be rapidly changed in any
desired sequence. The single-billet furnace also
has great operational flexibility, because there is
no requirement for a startup or billet-removal
procedure at the start of production or program
change, and changing to different billet lengths
is also quick.
Fig. 6.38 Single-billet induction coil with field extension Fig. 6.39 Multibillet induction coil with integrated shock
and tappings heating coil. TM, temperature sensor
368 / Extrusion, Second Edition
which is always constant at the exit end, varies tion to the mains, the furnace is usually balanced
at the input end. to give three-phase connection of a single con-
The control system is designed so that the trol zone at the end of the furnace.
transport mechanism always keeps the furnace Depending on the final temperature and the
correctly filled; that is, the furnace charge at the coil length, there is a more or less steep tem-
entry side is always within the minimum and the perature gradient in the furnace that is linear but
maximum limits. In a multibillet furnace for n not continuous. The number of steps corre-
billets, the maximum furnace load is n times the sponds to the number of billets in the furnace
next smaller billet length that (n Ⳮ 1) times just (Fig. 6.39). This temperature profile in the fur-
exceeds the maximum furnace charge. nace requires a special start up operation where
In practical press operation, the coil exten- two-thirds of the furnace charge must be re-
sions at the entry end are usually larger than de- moved, because the first billets do not have the
sired, and, as described, the billet ends will over- desired temperature.
heat. The excess temperature in this case will Prolonged holding periods create problems,
naturally not be as high as with single-billet fur- because the temperature profile in the billet col-
naces, because the billet is not heated over the umn in the furnace can vary significantly, so re-
full temperature range but only over a fraction, starting the production requires the linear tem-
the magnitude of which depends on the number perature gradient to be repeatedly redeveloped,
of billets in the coil. Accordingly, the excess which usually requires the removal of billets due
temperature at the end of the billet is naturally to incorrect temperatures. Maintaining the ap-
only a fraction of the excess temperature with proximately linear temperature gradient is, how-
single-billet furnaces. ever, important for the production, because var-
These excess temperatures practically even iations in the temperature steps from one billet
themselves out, particularly with billet materials to another result in changes in the billet-removal
with a good thermal conductivity. In cases in frequency. The production sequence then falls
which a suitable temperature accuracy is not out of synchronization.
achieved, this can be remedied, as described for The problems associated with the startup and
single-billet furnaces, by matching the coil shutdown operation are significantly less with a
length to the billet column length, using tappings three-phase furnace connection, because in this
on the coil. If this is still insufficient, then a field case, there are three separately controllable part
extension must be used. coils. This simplifies the attainment and main-
Multibillet furnaces can be classified into two tenance of the linear temperature gradient in the
designs according to the electrical connection. furnace. However, there is the problem that at
The first has a single-phase connection to the the boundary between the coils, the phase shift
coil, and the second a three-phase connection results in field weakening and thus temperature
(Fig. 6.40). With the single-phase coil connec- reductions. These temperature shadows often
Fig. 6.40 Induction furnace with single-phase (left) and multiphase (right) coil connection. TM, temperature sensor
Chapter 6: Machinery and Equipment for Direct and Indirect Hot Extrusion / 369
cannot be fully eliminated, particularly with The holding chamber has electric heating ele-
low–thermal-conductivity materials. ments. The brickwork used has a low thermal
Compared to single-billet furnaces, much capacity in order to be able to change the tem-
higher throughputs can be achieved with multi- perature of the hot holding chamber as quickly
billet furnaces. The throughput of a multibillet as possible. The length of the heated holding
furnace with n billets in the furnace corresponds chamber is 2.5 to 4 times the maximum billet
to the throughput of n single-billet furnaces with length.
the same specific energy input. In contrast to the The heated holding chamber fulfills two tasks:
single-billet furnaces, there is only a slight ● Equalization of axial and radial temperature
throughput reduction with shorter billets in the differences that occur during heating in the
multibillet furnace, and this is associated with induction furnace
the possible reduced furnace load and the higher ● Storage of heated billets to cover press in-
number of dead cycle times when the billets are terruptions
removed.
This combination enables the induction furnace
6.3.1.3 Induction Furnace with a to be fitted with more economic three-phase
coils, because possible temperature differences
Heated Holding Chamber
at coil junctions can be rectified.
Even the multibillet furnace has limitations The advance of the billets in the combination
similar to the single-billet furnace in terms of does not occur in increments of billet length, as
throughput. In many cases, the required through- in a standard furnace, but in small steps of ap-
put is so high that it cannot be achieved even in proximately 120 to 150 mm. In order to be able
a multibillet furnace, and two possibly slightly to operate as a billet buffer, the removal system
smaller furnaces must be provided. The opera- is designed so that billets can be removed from
tion of two or more furnaces that must feed the different positions within the heated holding
heated billets, in turn, is naturally associated chamber. In standard operation, the billet re-
with problems, particularly on startup after pro- moval from the heated holding chamber takes
duction interruptions and breakdowns, as well place when the front edge of the billet is ap-
as with production changes—all things that fre- proximately in the center of the heated holding
quently happen in normal extrusion plants. The chamber. If the billet cannot be removed at this
combination of an induction furnace with a point, the induction furnace is switched to a low
heated holding chamber was developed to over- load; that is, it operates at approximately 20%
come these problems, with the heated holding power and 20% of the speed until the billet has
chamber located immediately after the induction reached the position at the exit of the heated
furnace so that the heated billets pass directly holding chamber. This enables an interruption of
from the induction coil into the heated holding 15 to 20 min to be bridged. If the stoppage is
chamber (Fig. 6.41). longer, the billet advance is stopped, and the in-
Fig. 6.41 Induction furnace with integrated heat holding chamber for heating of copper and brass billets
370 / Extrusion, Second Edition
duction furnace is switched to heat-holding billet furnaces are necessary. The combination is
operation. In other words, the temperature gra- also used for copper alloys and steel.
dient in the induction furnace is maintained in
the individual coil segments by energy input cor- 6.3.1.4 Boost Heating
responding to the heat losses. The extrusion process frequently requires a
In contrast to the standard design, in which temperature gradient over the billet length. The
the furnace must be switched off during billet requirement for aluminum alloys, in particular,
removal to avoid ejection of the billets from the is for an axial billet temperature profile (see the
furnace, with the combination of the heated section “Process Control in Direct and Indirect
holding chamber it is not necessary to switch off Hot Extrusion of Aluminum Alloys without Lu-
the heating when a billet is removed. There is, brication” in this chapter).
therefore, no interruption to the heating process The heat developed by friction during extru-
during billet removal and, in addition, the dead sion is compensated by a temperature decrease
cycle times for radial and axial temperature toward the end of the billet. With suitable selec-
equalization are not required, because this takes tion of the temperature gradient from the front
place in the hot holding chamber. The combi- of the billet to the back, the billet cross-sectional
nation enables the same throughput as a standard discs always enter the deformation zone with the
furnace but with a significantly lower connected same temperature.
load. The elimination of the dead time on one With continuous billet-on-billet extrusion, the
hand and the continuous full loading of the coil air in the container must be completely removed
on the other also ensure that the throughput is during upsetting. The billet should bond with the
the same at all conceivable billet lengths. In ad- previous billet. The front of the billet should
dition, optimal temperature uniformity within have a higher temperature. Only a relatively low
the billets as well as between billets is guaran- temperature gradient is needed for air removal.
teed on removal from the furnace. The temperature gradient, therefore, has a max-
In most cases, two conventional multibillet imum value at the front of the billet and then
furnaces are replaced by a single unit—one com- drops rapidly and continues almost flat to the
bination induction furnace/heated holding back of the billet.
chamber. This considerably simplifies the opera- In indirect extrusion, as with direct billet-on-
tions. In particular, startup, alloy change, as well billet extrusion, the removal of the air from the
as dry-cycling operations can be carried out container is an important requirement. The bil-
semiautomatically, which is not possible with a lets must also be heated in the furnace with a
double plant. temperature that decreases toward the back.
The previously mentioned technical advan- The axial temperature gradients fall in a range
tages of the combination induction furnace/ up to 100 C. The magnitude selected depends
heated holding chamber over the standard fur- on several factors, including the extrusion pro-
nace reduce the plant costs, even if concrete cess, billet material (alloy), and billet dimension.
numbers cannot be given. The main saving is In contrast to aluminum alloys, the tempera-
in the investment costs, with the lower equip- ture gradient used with copper alloys has the
ment cost of a single plant compared to the maximum temperature at the back of the billet,
double plant and the smaller footprint as well as to compensate for the heat that flows into the
the significantly reduced connected electrical colder container.
power. Only the induction furnace is suitable for such
If the required throughput is in a range that a preheating process. Two different designs of
would not cause problems with a standard mul- boost heating systems are used to develop a tem-
tibillet furnace, the combination of the con- perature gradient over the billet length: the sin-
nected heated holding chamber and the more gle-coil boost heater, which is the simplest de-
complex transport mechanism is more expensive sign, and the somewhat more expensive but
to purchase. There are still the operational ad- more universally applicable segmented-coil
vantages and the resultant cost savings, but these boost heater.
are too small to be able to compensate for the The single-coil boost heater consists of a con-
higher investment costs of the combination over tinuous coil fitted with several connections.
an acceptable time. The use of the combination These connections enable the coil to be heated
is concentrated on the range of higher through- in several partial lengths that are successively
puts in which at least two conventional multi- shortened (Fig. 6.42).
Chapter 6: Machinery and Equipment for Direct and Indirect Hot Extrusion / 371
The distance between the individual connec- The two types of boost heater design are used
tions is 150 to 300 mm. The number of connec- in various versions. The simplest is the boost
tions, and thus heating steps, is determined by heater built into the coils of the preheat furnace
the maximum billet length. (Fig. 6.39).
After the billet has been heated uniformly to Here, similar to the single-coil boost heater in
the base temperature over the entire billet length, Fig. 6.42(a), the coil of the preheat furnace is
which is the requirement for single-coil boost fitted with several connections at the exit side,
heating, the entire coil is connected to connec- so that the coil end can be separately heated in
tion 1. Finally, the subsequent partial lengths are several length segments to develop the desired
connected through connections 2, 3, and 4. This temperature gradient. The standard heating and
produces an almost linear temperature gradient the boost heating cannot, however, be simulta-
over the billet length if the temperature is in- neously switched on, which naturally results in
creased by the same amount in the individual a throughput reduction for the preheat furnace.
heating stages. The waves that form in the tem- Another possible arrangement for the boost
perature gradient as a result of the reduced heat- heater is to integrate it into the preheat furnace.
ing lengths disappear, in practice, almost com- As shown schematically in the segmented-coil
pletely within a short time, and the extrusion heating system in Fig. 6.43, the boost heating
process is not impaired. Any desired tempera- coils are located directly after the coil of the pre-
ture profile decrease toward the end of the billet heat furnace. Because the coils of the standard
can be produced by suitable selection of the tem- heater and the boost heater are electrically sepa-
perature jumps and connection times in the in- rated from each other, they can operate simul-
dividual heating stages. taneously, so that in this version there is no re-
In the segmented-coil boost heater, the coil duction in the throughput of the preheat furnace
consists, as the name implies, of several coil seg- from the boost heater.
ments, the lengths of which act in the same man- A further possibility is to locate a separate
ner as the distances between the individual con- boost heater in the transport of the billet between
nections in single-coil boost heater. Each of the preheat furnace and the press loader. In this
these coil segments is fitted with its own tem- case, it is worthwhile to have greater flexibility
perature measurement and control system and by designing the boost heater as a combination
can be individually switched. This enables any single-billet preheat and boost heater in order to
desired temperature gradient to be developed, be able to raise the temperature of maximum-
even where the billet was not supplied with a length billets, which is often necessary when de-
uniform base temperature. veloping the desired temperature profile after
Fig. 6.42 (a) Single-coil heating. (b) Partial-coil boost heating. TM, temperature sensor
372 / Extrusion, Second Edition
Fig. 6.44 Induction furnace combined with a hot log shear for heating aluminum logs
Chapter 6: Machinery and Equipment for Direct and Indirect Hot Extrusion / 373
resulted in a furnace that satisfactorily met the In this heating method, the entire heat input
many requirements of a modern extrusion plant. must be through the billet surface. Therefore, the
The rapid-heating gas-fired preheat furnace is energy input cannot be as high as with the in-
therefore now extensively used in extrusion duction furnace, and rapid-heating gas-fired pre-
plants. heat furnaces require a correspondingly longer
In rapid-heating gas-fired preheat furnaces, time for heating than induction furnaces. The
the furnace chamber (Fig. 6.46) is a tunnel, simi- long furnace length requires the rapid-heating
lar to induction furnaces. However, in contrast gas-fired preheat furnace to be divided into sev-
to the induction furnace where a coil is needed eral zones, for good temperature control.
for each billet diameter, only one furnace tunnel,
matched to the maximum billet diameter, is used 6.3.2.2 Rapid-Heating Gas-Fired Preheat
for all billet diameters.
Furnace with Billet Preheating
Heating is by a number of burners uniformly
distributed on either side of the furnace tunnel The exhaust gases are very hot and contain
over the full tunnel length. For rotational sym- significant heat energy and therefore, provided
metrical heating of the billets, it is necessary to sufficient space is available, are used to preheat
arrange the burners in several rows, one above the billets. A zone is added to the heated section
the other, depending on the billet diameter. The of the furnace on the entry side, within which
exhaust gases are transferred via an exhaust duct preheating is carried out with the exhaust gases.
to the entry side and then fed into a flue. The length of this preheat zone should, for max-
imum effectiveness, approximately correspond
to the heated length of the furnace. There are
two types of preheat zones. In the simpler but
also less effective design, the gases flow in a
tunnel built onto the heated zone past the billets
to the entry side. Adequate turbulence of the ex-
haust gas flow is needed for good heat transfer.
The second method of preheating is to have
the returning hot exhaust gases blown through
nozzles at a high velocity onto the billet (Fig.
6.47). However, the recycling of the exhaust
gases only functions over a limited length, so
that the preheat section must be divided into sev-
eral recycling zones or fan fields. These preheat
Fig. 6.45 Temperature variation (1, theoretical; 2, practical) zones have a significantly higher utilization of
over the length of the billet in the cast logs in an the exhaust gas heat than the simpler design de-
induction furnace
scribed previously.
Part of the increased saving of thermal energy
is countered by the electrical current consumed
for the recycling fans in this version. The effec-
tiveness of this preheating is, by necessity, the
greatest at the maximum throughput and reduces
as the throughput falls, because the power
needed for the fans is independent of the
throughput.
preheat furnace can be used for this application. throughput, provided a coil is available for each
A typical installation is shown in Fig. 6.49. billet diameter. In other words, if several billet
diameters are being used, then a separate coil is
6.3.2.5 Rapid-Heating Gas-Fired needed for each billet diameter.
Furnace with Hot Log Shear The efficiency of the induction furnace is be-
tween 48 and 53% with conventional coils, and
The rapid-heating gas-fired furnace is fre- 58 to 67% for furnaces with low-loss coils.
quently used in combination with a hot log shear The efficiency of a rapid-heating gas-fired
to shear the extrusion billets from the heated alu- furnace without billet preheating is between 30
minum log. The furnace only supplies billets to 35%. This efficiency decreases when the
with an axially uniformly heated billet. If an ax- throughput is reduced and also if billets with
ial temperature gradient is required, an induction smaller diameters than the maximum are heated.
boost heater, as described in section 6.3.1.5, Efficiencies of 50 to 55% are obtained with a
must be installed between the hot log shear and preheat zone of the simplest design described
the press (Fig. 6.49). previously, and 60 to 65% with a preheat zone
with air circulation. The efficiencies given refer
6.3.3 Temperature Measurement to pure heat energy and the drive energies are
and Control not considered.
The temperature measurement and control is
by direct measurement of the billet temperature 6.3.5 Extrusion Billet
in both induction and rapid-heating gas-fired Transport Mechanisms
furnaces. The measurement points are always at
the exit of the individual zones. The energy input No specific transport mechanism is needed in
is always controlled as a function of the billet the furnace section of an induction furnace, be-
temperature. Thermocouples are used for tem- cause of the short furnace length. The billets are
perature measurement with aluminum alloys, pushed through the furnace on a slide plate. In
and optical systems for copper alloys. Care is contrast, with the rapid-heating gas-fired fur-
needed in the use of optical instruments in rapid- nace, a transport system must be included in the
heating gas-fired furnaces to ensure that the tem- furnace, because of the long length. Various sys-
perature measurement is not affected by the gas tems are used for the billet transport through the
flames. furnace, including chain, rollers, slide bars, and
walking beams.
The walking beam (Fig. 6.50a), which is by
6.3.4 Economics
far the most suitable version of all the systems
With induction furnaces, the specific energy mentioned, consists of two longitudinal supports
consumption is practically independent of the on which billet carriers in high-hot-strength ma-
Fig. 6.49 Rapid-heating gas-fired double plant for heating copper and brass billets
376 / Extrusion, Second Edition
terial are located. The spaces between the billet coil of the induction furnace. At the same time,
carriers are filled with heat-resistant ceramic. a billet at the extrusion temperature is removed
These billet supports taper upward and are lo- on the exit side. In the rapid-heating gas-fired
cated in the lower position of the walking beam furnace, the billet on the feed chute is only
in specific slits in the furnace floor slightly be- pushed up to the billet column, and further trans-
low the billet column. port through the furnace is taken over by the
The billet column rests on heat-resistant steel walking beam or the transport chain. If the fur-
supports in the hearth bottom and thus seals the nace has slide-ways or rolls, the billet pusher
furnace floor at the bottom apart from the short naturally pushes the billet through the furnace
operational time of the walking beam. in a manner similar to the induction furnace.
However, the walking beam can only be used With both furnace types, the removal system
if sawn billets are being heated. It cannot be used consists of a clamp that pulls the billet from the
with a rapid-heating gas-fired furnace/hot log furnace. The next billet in the furnace is then
transported to the removal position. The billets
shear combination. In this application, nondri-
removed from the furnace are transported by a
ven rolls fitted in the furnace floor have proved specific transport mechanism to the press billet
successful (Fig. 6.50b–6.53). loader.
The transport mechanism outside the furnace If the furnace is combined with a hot log
is practically identical for the induction furnace shear, the log is pushed out of the furnace into
and the rapid-heating gas-fired furnace. The bil- the hot log shear by the billet-pusher system.
lets from the billet store, which, in the simplest After shearing the billet, the remaining log is
case, consists of a sloping storage table, are pushed by a billet pusher from the shear and
transferred on demand onto a feed chute from back into the induction or rapid-heating gas-
where they are pushed by a billet pusher into the fired furnace.
Fig. 6.50 Cross section of a rapid-heating gas-fired furnace with (a) walking beam transport system and (b) roller conveyor transport
system
Chapter 6: Machinery and Equipment for Direct and Indirect Hot Extrusion / 377
The subsequent transport of the sheared billet to in the industry as the handling system. The
to the press takes place in the normal way, either downstream system and the finishing machines
directly or via a boost heater. for the handling and preparation of the extruded
products vary considerably.
The downstream equipment for the produc-
tion of wire is largely independent of the mate-
rial and is simple in principle. The method of
Handling System cooling the wire is important. With water cool-
ing, the space required is small. If air cooling is
Horst H. Groos* necessary, the space needed is significantly
larger. Downstream equipment for the produc-
The finishing system, consisting of the down- tion of wire is not nearly as complex as for rod,
stream system for extrusion presses, is referred section, hollow section, and tube. With extrusion
Fig. 6.51 Rapid-heating gas-fired furnace for aluminum bars in combination with a hot billet shear and shock heating furnace
Fig. 6.53 Rapid-heating gas-fired furnace with transport rolls 6.4 Handling Gear for
Aluminum Alloy Products
Originally, a stationary table was located after
the platen as the run-out table. The extruded sec-
tions were guided by hand by the operators with
plants that are only designed for the extrusion of tongs. Later, as more and more easily extruded
tubes, the downstream equipment is relatively aluminum alloys (e.g., AlMgSi0.5) were pro-
simple, depending on the method of cooling. cessed to architectural sections, handling gear
When the extruded products leave the press, was installed that made it possible to economi-
they are at approximately the temperature of ex- cally extrude large lots. The slat conveyor was
trusion. In many cases, they are bent and twisted, widely used as the press run-out table, running
and in addition, they also have, to some extent, approximately 3% faster than the exit speed. The
unusable front and back sections. They are too cooling took place immediately behind the
long for further processing if they cannot be platen with air or, when necessary, on the walk-
coiled. The handling system corresponding to ing beam transverse conveyor forming the cool-
the operational conditions must guide, cool, ing table, leading to the stretcher, storage table,
straighten, and section the extruded product as and saw line with roller conveyor, cut-to-length
well as handle the end discards and scrap. saw and saw gage, as well as the necessary trans-
The handling system also must prepare the fer systems. This system is still used in many
extruded product so that it is ready for sale or extrusion plants.
optimally prepared for further processing. The The handling system described here is always
aim is always to produce products that are as suitable when from the point of view quantity
close to being finished as possible. Aluminum and quality, the operating procedures guarantee
alloy sections are an example that are cut in the an economic extrusion. The operating procedure
extrusion plant to the length needed by the end is simple and easy to follow under normal pro-
user, for example, for window manufacture. duction conditions.
Whether direct or indirect extrusion is used is of During extrusion, the section or sections are
secondary importance for the handling system. guided by the slat conveyor. After extrusion, the
The many different handling systems cannot section is separated from the discard at the die.
be fully described in the context of this discus- The slat conveyor then increases speed and
sion. Therefore, only the most common handling moves so that the section or sections are in the
Table 6.16 Downstream equipment for different products in aluminum (light metal), copper, and
steel
(continued)
Dark shading, standard equipment; light gray, alternative equipment; open spaces, special.
380 / Extrusion, Second Edition
position of the walking beam cross-transfer sys- competition by saving personnel. This led to fa-
tem. Lift-off arms are then moved between the vorable lot sizes as well as profile cross sections
static arms of the walking beam cross transfer. and lengths that were easily transported. The
These lift the section, move it out, and place it most important requirement is to be able to ex-
on the walking beam table. After the transport trude continuous sections, for example, billet-
time, which is also the cooling time, the sections on-billet extrusion.
are transferred from the walking beam cross- In the deformation zone in front of the die,
transfer conveyor to the stretcher for correction. there is always sufficient material being de-
After the stretcher, the sections arrive at the stor- formed so that welding of the material with the
age table, where batches of several sections are new billet is ensured [Thu 84].
collected. These are then transferred to the saw The press run-out table consists of an inter-
line. The longitudinal conveyor of the saw line mediate table between the platen of the extrusion
consists of a roller conveyor or a belt conveyor. press and the cooling table, followed by a slat
In the saw line, the sections are cut and divided conveyor that can be lowered. This is fitted with
into commercial lengths. Two stops that can be a puller and guide rail with a movable shear
adjusted and swung out of the way are used. The and/or saw for cutting the extruded sections.
scrap ends and the excess lengths of scrap are The intermediate table is a movable slat con-
removed in front of and behind the cut-to-length veyor. The length depends on the maximum
saw by tilting table segments. After the cut-to- commercial lengths. A shear or saw (or both in
length saw, the sections cut to commercial combination) for cutting the hot continuous ex-
lengths are transported to the manual-removal trusions is linked to the movable slat conveyor
section, where they are placed in racks. The sub- and can be positioned according to the commer-
sequent treatment of the extruded sections, in- cial length. The slats in the run-out table consist
cluding age hardening, anodizing, painting, of supports with graphite inserts.
packing, and so on, are carried out according to The shear or saw is positioned to produce the
requirements. [Ell 88] desired commercial lengths without unnecessary
The development of the automatic aluminum scrap. After cutting the extruded product, the
alloy handling system commenced in the Euro- shear or the saw withdraws in the opposite di-
pean extrusion plants (Fig. 6.54). The intention rection to the extrusion to obtain receive a free-
was to obtain a cost advantage in the face of hard standing section. The puller picks up the still-
Chapter 6: Machinery and Equipment for Direct and Indirect Hot Extrusion / 381
stationary section (it could also be several man operation. Automatic operation of the han-
sections) in the area of the intermediate table. dling gear is only possible if several sections
At the start of extrusion, the puller starts to from one billet are always manipulated as a
move synchronously with the section exit speed batch into the stretcher and stretched.
and guides the extruded product under con- The sections or batches are gathered on the
trolled tension. After the billet, the length of collection belts of the collection table. These
which has been determined from the number of batches should also consist of the same products.
possible commercial lengths and the expected The width of the saw line is determined by the
scrap, has been extruded to the discard length, economic production of the extrusion press and
the puller stops. The extruded product is cut in the shortest still-practical commercial length.
the region of the intermediate table, and the Even if the cut-to-length saw has a fast cycle
puller pulls it to the transfer position to the cool- time, it can be a bottleneck if short commercial
ing table. As the slat conveyor lowers to enable lengths are required and/or the saw line is not
the section or sections to be moved to the trans- wide enough. The extrusion press then stops be-
fer table, the puller returns at high speed to the cause of the delay in the sawing area.
collection position for the next extrusion. The The saw line consists of the roller conveyor
transfer belts of the cooling table that extend into before the cut-to-length saw and the cut-to-
length saw with double-cut end clearance and
the slat table are below the run-out table during
swarf extraction. The roller conveyor behind
extrusion.
the cut-to-length saw is fitted with scrap and
All the transfer conveyors, including the cool- section gage stops that can be adjusted to dif-
ing table, the stretcher transfer, the stretcher ferent commercial lengths. Both roller convey-
clearance, as well as the collection table, con- ors in front of and behind the cut-to-length saws
sist of fixed transport belts that can be moved can be lowered for feed and removal of the ex-
longitudinally for transfer. Graphite-lined chain truded sections. The cut-end removal is carried
conveyors are used for extremely demanding out on both sides of the saw blade by tilting
operating conditions. Transfer belts are more conveyor units. The scrap is transferred by
flexible and better suited for manipulation than chutes and conveyor belts to a container or col-
walking beams. The fans for cooling the sections lection area (Fig. 6.55).
before stretching are located under the cooling The extruded sections cut to commercial
table as well as the run-out table (Fig. 6.55). lengths are transported by belt conveyors to a
The stretcher is designed for automatic opera- stacking machine. Here, the sections are stacked
tion. If necessary, it can be used for one- or two- on transport racks with spacers located between
382 / Extrusion, Second Edition
the individual layers so that the aging oven can racks reach the destacking machine. Here, the
be supplied with a sufficient quantity of extruded sections are placed on the belt conveyor of the
sections. After age hardening, the transport packing line. The empty transport racks and the
Fig. 6.55 Schematic drawing for the operational steps in an aluminum alloy extrusion plant
Chapter 6: Machinery and Equipment for Direct and Indirect Hot Extrusion / 383
spacer are returned again to the stacking ma- tect the wire surface. The coilers usually have
chine [Höl 88]. direct current drive and are synchronized with
the press via the extrusion ratio. Because the exit
speed cannot be held constant, due to production
tolerances and wear of the die as well as other
6.5 Handling System for
operational conditions, and cannot be directly
Copper Alloy Products determined from the emerging wire, the irregu-
larities must be manually controlled.
The handling system for copper alloys is, to The wire coil is layered during the coiling by
a large degree, determined by the extruded prod- a wobble control to produce coils for the further
uct. (Fig. 6.56). It is necessary to differentiate processing of the wire. The protective baskets
between handling systems for copper and copper filled with the coils are transferred on a longi-
alloys and brass as well as handling systems for tudinal conveyor designed as a cooling section.
mixed programs. There are additional differ- In the last part of the cooling section, the coils
ences between wire, strip, section, and/or tube are also cooled with water. After this, the coils
production. Frequently, mixed programs are (wire and bar) are transferred by a coil handler
necessary, which result in multifunctional and to a capstan or directly to a hook conveyor. The
thus expensive handling equipment. Copper is empty protective pans are transferred from the
preferably extruded directly into water to avoid position of the coil handler to a parallel second
undesired oxidation of the surfaces. Brass, how- conveyor that returns them to the coiler. The
ever, cannot be extruded directly from the extru- coils are transferred from the capstan or the hook
sion temperature into water. Water cooling is conveyor for further processing.
first used when the temperature of the extruded
section is less than 350 C. In contrast to alu- 6.5.2 Wire Line: Brass Wire Transport
minum alloys, there has not been any develop- without Protective Baskets
ment toward a standard handling system with
copper alloys. Two down coilers with integrated coil pans
and elevating pan bases are preferably located
6.5.1 Wire Lines: Brass Wire after the press platen. The wire guide channels,
coiler drive, and coiler control are identical to
Transport with Protective Baskets
those already described. Because the pan base
Two down coilers with coiler crowns to re- must be raised to transport the coil, additional
ceive protective baskets that can be raised and mechanical and hydraulic systems are needed.
lowered are preferably located after the press The larger masses require a more powerful
platen. Between the press and the coilers are drive. After the transfer of the loose hot coils,
wire guide channels. The channels are prefera- they are transferred by a plate conveyor forming
bly fitted with replaceable graphite strips to pro- the longitudinal conveyor. The plate conveyor is
designed as the cooling stage for the wire coils guided safely and carefully. The run-out table
and must be of sufficient length to correspond itself must have a smooth, nonabrasive table sur-
with the press cycle time and the maximum wire face. Roller conveyors have proved successful.
volume. To avoid surface defects, the transfer These have smooth surfaces apart from a rela-
and transport must be carefully carried out. tively narrow region in which the rolls stand out
Pushing and sliding of the wire coils can result only a few millimeters. The roller conveyor op-
in transverse grooves on the wire surface. At the erates all the time during extrusion. The roller
end of the plate conveyor, there is an immersion conveyor speed is synchronized with the extru-
bath for cooling, coil binding machines to bind sion speed, as described for coiler systems. To
the open wire coils, and a coil handler to transfer ensure that the emerging extrusion is guided
the wire coil to a capstan or a hook conveyor. safely and straight, the roller conveyor must be
The coils are then moved on for further pro- approximately 3% faster than the extrusion
cessing. speed. The rolls stop with the extrusion and are
lowered. The section is then resting on an almost
6.5.3 Wire Line: Copper Wire Transport closed table with only slots at the location of the
rolls. The slots do not have any negative effect
without Protective Baskets,
on the already partly cooled extrusion. After
Cooling under Water separation of the section from the discard, the
One or two down coilers with solid coiler extruded product is transported by rolls into the
bodies and elevating pan bases are located after area of the walking beam cross-transfer con-
the press platen. The coiler bodies are in the wa- veyor. A sweep push-off arm pushes the section
ter container. The coiler drive located outside the onto the walking beam cross-transfer conveyor,
water basin and the coiler control have already which acts as a cooling table. The static and
been described. The wire guide channels are de- movable walking beams must be as close to each
signed without graphite blocks. They are other as possible. The section pushed off by the
flooded with treated water during wire produc- sweep-off arm is straightened over its length and
tion up to the die to attempt to prevent possible rests on the walking beam cross-transfer con-
oxidation of the wire surface. A special jet tube veyor at a suitable distance from the previous
between the extrusion tooling and the channel section. This produces the optimal conditions for
within the press platen keeps the water from the cooling and subsequent transfer to the saw roller
die when extrusion is stopped. The channel can conveyor. A test roller conveyor with a fracture
be closed with sluices in front of the coiler inlet test machine is located in the area of the walking
so that the water cannot run out after coiling. beam cross-transfer conveyor and is used for
The operating sequence after coiling is coil el- material control of the extruded product. The
evation, push off, and transport away via a short cooled sections are transferred as a batch to the
plate conveyor, as well as coil binding, coil col- saw line, where they are sectioned to commer-
lection, and transfer to a capstan or hook con- cial lengths or to lengths for subsequent pro-
veyor. cessing and finally transferred to a collection
trough.
6.5.4 Straight Line: Brass Transport for Alternatives to the systems described are:
Rod, Tube, and Section ● Instead of the run-out roller conveyor, a
Handling systems for brass products are used closed run-out table with single or multiple
to handle extremely sensitive extruded products. pullers. One or more sections are individu-
The surfaces in the hot phase, in particular, can ally guided and pulled. The sections are then
be easily damaged immediately after extrusion. guided in the same manner as aluminum al-
The problem is that these defects are often only loys but with significantly more care with
detected much later during further processing. tension control during the extrusion.
Therefore, procedures must be put in place to ● Instead off the sweep-off arm, longitudinally
produce qualitatively defect-free products. moveable solid arms extend from the walk-
Behind the press, the run-out table is con- ing beam cross-transfer conveyor, which rest
nected to the platen by a short intermediate table in the run-out table during extrusion. After
that is as close as possible to the die and is the section is in the position of the walking
matched to the height of the extrusion cross sec- beam cross-transfer conveyor, the run-out ta-
tion. This enables the extruded products to be ble is lowered, and the movable solid beams
Chapter 6: Machinery and Equipment for Direct and Indirect Hot Extrusion / 385
carry the section into the cooling bed area. ther processing and finally transferred to a col-
This ensures careful handling of the sections. lection trough (Fig. 6.57).
Transverse scoring on the surface of the sec-
tions does not occur.
Fig. 6.57 Copper alloy extrusion plant (wire, bar, and section)
386 / Extrusion, Second Edition
the extrusion of brass and copper is expensive up to the die holder. The feed to the tool set,
and therefore rarely seen. which can be changed, must be reliable and ca-
The extrusion cooling system is designed for pable of being disconnected. When integrating
the specific function, depending on whether alu- such a cooling system with liquid nitrogen, the
minum alloys, copper alloys, or austenitic steels low temperatures that occur must be taken into
are being extruded. Air cooling is used for alu- account. Care must be taken to ensure that un-
minum sections that are easy to extrude and do dercooling of the tool zones and involved press
not have a large cross section and for brass al- components does not result in failure from ther-
loys that must not be cooled with water. The mally related stress concentrations.
intensity of the air cooling is relatively low. In- The advantage of this method of cooling is
creasing the cooling is possible if water is added the good transfer of the deformation heat from
in the form of a spray mist, provided that the the die region and an improved section surface
water addition does not result in a fog that would finish. In addition, the nitrogen also acts as an
be detrimental to personnel and equipment. oxidation barrier. The production output is in-
Water cooling is used for moderately difficult creased by the faster exit speeds, and the quality
and difficult-to-extrude aluminum sections with of the products is improved [Mar 88].
large cross sections as well as for copper and The cost of nitrogen cooling in the area of the
copper alloys and austenitic steels, which can be tooling is significant. In the case of die cooling,
water quenched. The water cooling has a high the complex special design of the die increases
cooling effect. Although direct contact between the cost. Nitrogen cooling is used for special ap-
the water and the surface of the extrusion is not plications in the extrusion of aluminum alloys.
possible at high temperatures for physical rea-
sons, the cooling effect of water is approxi-
mately 100 times that of air. 6.6.2 Water Cooling
Cooling results in: Cooling extruded sections of aluminum alloys
●
with water was used at a relatively early stage.
Restriction of grain growth
●
Systems were developed for specific applications.
Attainment of the solution heat treated
A very effective water spray system was suc-
quenched condition for age-hardening alloys
●
cessfully developed for aluminum cable sheath-
Improvement of the quality of the surface
●
ing that acted immediately behind the die. The
Prevention of oxidation
●
cable insulation, which is extremely tempera-
Development of nonsensitive surfaces
●
ture-sensitive, must be protected from damage
Protection of the handling system from di-
or even combustion. Although the dead cycle
rect overheating and abrasion
●
periods when the billets are loaded are particu-
Possibility of sawing the section at room
larly critical, the extremely effective cooling is
temperature
●
sufficient.
Increase in the exit speed of the extrusion
In the extrusion of sections of higher-alloyed
and the ram speed (compare the section
aluminum materials, a high material strength
“Process Control in Direct and Indirect Hot
must be achieved. Immersion cooling in the
Extrusion of Aluminum Alloys without Lu-
form of a standing wave located after the press
brication” with Section 6.6.1).
platen can be fitted in the run-out table for this
The disadvantages are purpose. It consists of a flat water chamber that
●
is open along the press axis. The water wave is
Distortion of the section
●
formed by two flat nozzles angled toward each
Increased expenditure to prevent mechanical
other to produce a standing wave. The extruded
and electrical water damage
● Press operators subjected to noise and water
sections then undergo a type of immersion cool-
ing as they are extruded. The section is inten-
vapor
sively cooled in a minimum of time. The dis-
advantage is that the upper section side is cooled
6.6.1 Nitrogen Cooling
less than the lower section side. The high cool-
Nitrogen is used to cool the extruded section ing rate is associated with distortion of the sec-
and to cool specially designed dies in the extru- tion with unequal cross sections, and this hinders
sion of aluminum alloys. The extrusion press further transport. The resultant downstream cor-
must be designed for the feed of liquid nitrogen rection results in considerable additional costs
through a suitable tube system in the platen area for the extrusion plant.
Chapter 6: Machinery and Equipment for Direct and Indirect Hot Extrusion / 387
More recently, water section cooling systems With aluminum alloys, the section cooling
have been built with spray cooling, which rep- commences immediately after the platen.
resents a technically acceptable solution for ef- With aluminum sections that are easy to ex-
ficient and economical operating handling gear. trude and do not have a massive cross section,
With an acceptable effect on the surrounding sufficient cooling can normally be achieved with
area, defects including distortion of sections, in- overhead fans (Fig. 6.58) (axial fans with sheet
adequate operational safety, noise levels, and metal deflectors) and with undertable fans (sim-
water mist for the operating personnel can be ple axial fans) arranged under the press run-out
avoided. The intensity of the water quenching table as well as additional undertable fans stand-
can be varied by the use of different nozzles and ing in rows under the cooling table. The sections
adjustable water pressure. The spatially con- should only be hot enough to hold during
trolled cooling produces a symmetrical cooling stretching, never exceeding 60 C (140 F). In
effect on sections with unequal cross sections addition, with age-hardening alloys, specific
and/or unequal wall thickness [Edw 92]. The cooling rates must be maintained.
water section cooling system behind the press The method of working with air can only
platen is part of the run-out table. It consists of be used to a limited extent, for economic rea-
a lower and an elevating upper section to give sons and the effect on the surroundings (in-
access to the extrusion run-out table if water cluding noise level). The maximum air veloc-
cooling is not used. If required for production, ity is 15 m/s (50 ft/s).
it can be brought into operation from a control A significant improvement in the air-cooling
desk. intensity is obtained with high-speed air-cooling
The cooling of copper alloy extrusions with systems operating as a closed system. The cool-
water is only used for copper and specific alloys. ing intensity of the system is optimized by
Brass, which may not be direct water cooled for matching the cooling intensity of the system
metallurgical reasons, cannot be immediately with the geometry of the section being cooled.
quenched in water from the extrusion tempera- The use of these high-speed air-cooling systems
ture. has already proved successful in well-known ex-
The recrystallization of copper takes place in trusion plants. They consist of an upper and a
a very short time interval during extrusion at lower slit-shaped nozzle system transverse to the
temperatures of approximately 900 C. The extrusion direction, an extrusion run-out section
coarse grain that would form without water as a roller conveyor, the radial fans, and the
cooling is undesirable for further processing of housing. The length of the high-speed air-
the extruded section. Oxidation in this high- cooling system can extend to 5 m (16 ft). This
temperature region also commences immedi- cooling enables the cooling effect to be matched
ately after the die. Coarse grain formation is pre- to different sections by control of the nozzle exit
vented, and oxidation is largely avoided by velocity over the section width and by the height
using cooling tubes that extend into the tooling. adjustment of the upper slit nozzles.
The cooling tube carries the cooling water up to
the die during extrusion. Outside the extrusion
time, it acts as a jet tube and prevents the water
flowing from the water bath into the extrusion
run-out region. The intensive cooling effect of
the water ensures that the extruded section is
thoroughly cooled during an extrusion cycle and
can be taken in a bright condition from the water
bath.
ture tolerance of approximately Ⳳ2.5 C (Ⳳ4.5 is approximately 1.5 h and the subsequent equal-
F). Particular attention is required on the side ization time is approximately 1 h. The heating
of the furnace by the manufacturer to ensure that in the outer regions of the section stack is faster
the connected heating load (wattage) is compat- than in the core. Sections with a high weight per
ible with the circulating air volume; otherwise: linear meter density heat up more slowly than
● If the connected load is too low, the air takes small sections.
too long to return to the desired temperature
after loading a batch. 6.7.1 Methods of Air Circulation
● If the connected load is too high, the circu- The air circulation within the oven is usually
lating air volume is insufficient to transfer longitudinal, that is, parallel to the section (Fig.
the heat available to the charge being heat 6.61).
treated. Uniform stacking of the sections being heat
Excessive connected load is not worthwhile, treated in the oven as well as a uniformly dis-
because the reduction in the heating time is rela- tributed air input into the furnace working space
tively small compared to the total time due to are particularly important for efficient air distri-
the long holding time during age hardening. bution.
Figure 6.60 shows the temperature curves in The air flow can be further divided in the lon-
an age-hardening oven where the heating time gitudinal direction, as shown in Fig. 6.62. The
oven operates with two air currents, each with a advantage of these fans is that reversible air flow
separate heating and control. can only be achieved by additional dampers.
6.7.2 Fans
The circulation of the hot air is carried out by
axial or radial fans. Axial fans have the advan- 6.8 Design of the Chamber Furnace
tage that the air current can be reversed by re-
versing the fan motor. They have the disadvan- Age-hardening ovens consist basically of a
tage that the air volume and air pressure are steel sheet external and internal housing (Fig.
restricted; that is, axial fans cannot be used for 6.63, 6.64). The insulation in the form of mats
larger air velocities and larger furnaces and the or loose insulation material is located between
associated larger pressure losses. In addition, the these housings. It is possible to also have the
axial fans only achieve 60 to 70% of the maxi- oven without an inner housing. The heating duct
mum air throughput when reversed. within which the heating is installed is located
With radial fans, there is practically no restric- above and separate from the oven working
tion in the pressure and air capacities. The dis- space.
2. Transfer of the melt from the casting furnace Continuous casting plants are being fitted
to the casting system with process control systems to an increasing
3. Casting the melt extent, and the most sophisticated enable a fully
automatic casting process from the tilting of the
A typical continuous casting plant can have furnace, control of the metal head in the casting
two melting or casting furnaces that are charged launder and molds, to setting and control of the
with solid metal (scrap, billet off-cuts, ingots) or casting parameters and the start of the dropping
with liquid metal, either from a remelting plant of the casting table. The most important aim of
(aluminum alloys) or from an electrolytic cell in this full automation is to increase the operational
a smelter (pure aluminum). The casting furnace reliability of the casting process and to improve
can also be connected to separate melting-fur- reproducibility of the billet quality.
naces and melt-treatment furnaces. Melt-clean- Before the billets are delivered to the extru-
ing operations, including settling, salt, and scav- sion plant, they are given a homogenization heat
enging gas treatment, are carried out in the treatment and then sawn to the billet lengths re-
furnace to remove nonmetallic impurities. In quired by the extrusion plant.
modern continuous casting plants, additional
melt-cleaning systems for scavenging gas treat-
ment and filtration are integrated into the casting 6.11.2 Melting and Casting Furnaces
launder between the furnace and the casting sys- The furnace used for melting aluminum in-
tem. These are referred to as in-line melt-refin- clude hearth furnaces, hearth furnaces with
ing systems. In addition, the standard equipment closed-front hearth, dry hearth melting furnaces
includes a dosing unit for the continuous feed of with built-in holding chamber, shaft furnaces,
AlTiB grain-refining alloy into the melt in the channel induction furnaces, crucible induction
casting launder. The actual casting system casts furnaces, and resistance furnaces. Of these fur-
multiple logs semicontinuously. The number of nace types, the combustion-heated furnace is the
simultaneously cast logs depends on the diam- most suited for melting, from a thermal tech-
eter, the size of the casting plant, the casting nological point of view. The hearth melting fur-
length possible, and the furnace capacity. Extru- nace is of particular importance (Fig. 6.65) [Hen
sion billet diameters vary from 80 to 800 mm, 83]. Figure 6.66 shows a hearth melting furnace
with a casting or log length of up to 8 m. There plant.
are extrusion billet casting plants that can si- These furnaces are usually heated with gase-
multaneously cast 150 billets. The arrangement ous (e.g., natural gas) or liquid fuel (oil). The
of the molds depends on the method of feeding design of the furnace attempts to achieve an op-
metal into the molds. This is discussed later. timal balance between the shape of the furnace
Fig. 6.65 Schematic diagram of a modern hearth smelting furnace [Hen 83]
Chapter 6: Machinery and Equipment for Direct and Indirect Hot Extrusion / 393
Fig. 6.66 Modern hearth melting furnace. Source: Gautschi, Tägerwillen, Switzerland
chamber, the type, number, and spatial arrange- An unavoidable standard component of a
ment of the burners, as well as the controlled modern melting furnace is the furnace chamber
flow of the hot gases in order to transfer a high pressure control. This ensures that in every op-
fraction of the heat to the charge by convection. erational condition neither cold air nor entrained
Hearth furnaces are built with rectangular or air can be sucked in nor hot gases forced out of
oval cross sections as well as circular furnaces, the furnace chamber. A slight positive furnace
although the rectangular design is the most com- chamber pressure has proved successful in prac-
mon furnace type [War 77]. A shallow bath tice.
depth and a relatively flat hearth space are char- In modern melting plants, the thermal content
acteristic of these furnaces [Hen 80]. The tem- of the hot gases is utilized as much as possible
perature difference in the melt is minimized by to reduce the energy consumption in melting.
the shallow bath depth. For example, this can be by preheating the com-
The heat energy is supplied by burners. The bustion air. Heat-resistant steel or ceramic re-
choice of the burner depends on the type of fuel cuperators are used. The preheat temperatures
and the furnace design. The burner capacity is developed are between 300 and 540 C but can
limited by the available furnace space, the fur- reach 800 C with ceramic recuperators [Rei 80,
nace lining, and the exhaust gas flue. To ensure
War 85]. The preheating of the combustion air
the maximum convective transfer to the charge,
can be carried out with recuperative burners in-
the arrangement of the burner system in the fur-
nace chamber is of particular importance. In stead of separate recuperators [Rot 84]. Ceramic
practice, burner arrangements in which burners regenerative burners can also be used [Jas 86].
of different capacities and characteristics are an- These enable significantly higher preheat tem-
gled relative to each other and inclined to the peratures to be used.
charge have proved successful [Pas 84]. Burners Air preheating by recuperative or regenerative
that transfer a large part of the heat by convec- systems, however, is associated with harmful
tion are usually high-velocity burners (convec- emission problems, because high combustion
tion burners) in which the combustion gases temperatures, which inevitably occur with pre-
have a high-velocity (100 m/s, or 300 ft/s). heating of the combustion air, promote the for-
The burners are usually operated with a slight mation of nitrogen oxides (NOX) [Jun 84].
air excess resulting in a fast, complete combus- Combustion must be carried out with a low air
tion; afterburning in the furnace chamber is ex- excess and the temperature in the combustion
cluded. This results in economic fuel use. zone reduced to limit the NOX emissions.
394 / Extrusion, Second Edition
Casting furnaces are usually hearth furnaces mat. The oxide inclusion forms described
fitted with less powerful burners than the melt- previously frequently occur as agglomerates and
ing furnaces, because the melt only has to be are then referred to as oxide flakes [Lec 79].
held at temperature. Heat transfer by radiation is The impurity content of an aluminum melt is
more suitable. Radiation burners are used, and mainly influenced by the individual production
these have a significantly lower combustion gas steps in the production of extrusion billets. The
velocity (50 m/s, or 150 ft/s or less) [Wie 83]. various dissolved and undissolved nonmetallic
However, because the main heat input into the impurities in the extrusion billets can result in
melt is through the surface, there is a tempera- different defects during further processing. The
ture gradient that depends on the bath depth, the nature and extent of these defects depend on the
furnace temperature, and the holding period. shape of the impurities and also on the further
This can result in localized overheating in the processing, the treatment processes used, as well
surface regions of the melt. Therefore, modern as the quality requirements. The occurrence of
furnaces are also fitted with a system for melt the impurities in aluminum melts requires a
circulation. This is designed so that turbulent melt-refining process. The melt-refining pro-
currents do not occur. The advantages of metal cesses used in continuous casting plants can be
circulation are the reduction of the temperature classified into the following cleaning methods:
differences in the melt bath, homogenizing of
● Settling treatment
the melt, higher melting rates by more rapid dis-
● Vacuum treatment
solution of solid metal into the melt, lower en-
● Salt treatment
ergy costs, and lower melt losses. The metal cir-
● Scavenging gas treatment
culation is carried out by metal pumps or
● Filtration
electromagnetic stirring systems installed under
the furnace base [Nef 93, Saa 93]. The settling, vacuum, and salt treatments are
Finally, it should be mentioned that both sta- usually carried out in the casting and/or melting
tionary and tilting design are used for the hearth furnaces, whereas filtration takes place in the
furnaces for melting and casting aluminum. casting launder between the furnace and the
casting plant. A scavenging gas treatment can be
carried out in the furnace in a separate chamber
6.11.3 Processes for Melt Refining
integrated into the casting launder system or in
The impurities in the aluminum melt can be a combination of both. The methods listed above
divided into dissolved and undissolved impuri- have different effects on the different types of
ties. impurities in aluminum melts. Whereas the pri-
Hydrogen is the most important of the dis- mary purpose of vacuum and scavenging gas
solved impurities. Hydrogen enters the melt treatments is to remove hydrogen, the settling,
mainly from reaction of water vapor, which can salt treatments, and filtration processes only re-
come from several sources, with the liquid alu- move undissolved impurities.
minum. Excessive hydrogen can result in poros- In the settling treatment, the reduction of the
ity in the extrusion billet and heat treatment blis- content of undissolved impurities is by the de-
ters in further processing. position or the collection of the inclusions on the
The undissolved nonmetallic impurities are furnace floor or the bath surface. In the salt treat-
far more important to the quality and further pro- ment, the inclusions are removed by the injec-
cessing of an extrusion billet. The inclusions tion of salts into the melt in the furnace. The
form either during the melting process, the melt salts consist mainly of mixtures of chlorides and
treatment, or the casting process. The various fluorides of sodium and potassium. Their effect
types of inclusions must be differentiated. Ox- is mainly attributable to a flotation effect.
ides, nitrides, carbides, and borides are the most The scavenging gas treatment is particularly
frequent inclusions. The oxides are mainly effective in the removal of dissolved impurities,
Al2O3, which can exist in amorphous form as a particularly of hydrogen. In this refining
thin oxide skin and also as very fine polygonal method, inert gases (argon and nitrogen) or re-
crystals. In magnesium-containing aluminum active gases (chlorine) are passed through the
melts, magnesium oxides (MgO) and/or AlMg melt. The hydrogen dissolved in the melt dif-
mixed oxides (Al2MgO4) are frequently ob- fuses into the scavenging gas bubbles formed
served along with aluminum oxides. These ox- and is removed from the melt by the rising bub-
ide particles usually also have a polygonal for- bles. A high rate of degassing requires a uniform
Chapter 6: Machinery and Equipment for Direct and Indirect Hot Extrusion / 395
Fig. 6.67 Schematic diagram of the rotors in scavenging gas treatment systems. n, rotational speed (rpm) [Ter 87]
distribution of the bubbles in the melt and a large unit time. This rate varies in practice because it
total bubble surface. The latter requires a large depends both on casting speed as well as on the
number of small bubbles at a constant gas flow number and size of the extrusion billets that are
rate. Accordingly, the injection process must be simultaneously cast. For this reason, systems
designed so that small scavenging gas bubbles with different capacities are used that operate
are produced. with one, two, or three rotors. The chambers are
In the furnace, the scavenging gas is injected heated electrically, either with wall heating, tu-
by lances. In order to treat the entire melt, the bular heaters immersed in the melt, or with in-
lance must be moved through the melt bath. ductors installed in a chamber. The chamber is
In-line treatment has become very important clad with either graphite or suitable refractory
for scavenging gas treatments. The treatment is ceramics. The system can be tilted to empty the
carried out in a separate chamber between the chambers. The efficiency of the systems now in
casting furnace and the casting plant. In this pro- use enable hydrogen contents of 0.15 Ncm3/
cess, rotors fitted with nozzles are used to inject 100 g aluminum (0.15 ⳯ 10ⳮ9 cm3/100 g alu-
the scavenging gas, and these produce a good minum) to be achieved.
distribution of the fine scavenging gas bubbles A scavenging gas treatment reduces the con-
within the melt in the treatment chamber. The tent of undissolved impurities as well as reduc-
processes available at the moment operate using ing the hydrogen content. The inclusions are re-
the same principle but differ in the design and moved by the flotation of the gas bubbles. This
the shape of the rotor. Figure 6.67 shows the requires the presence of small gas bubbles and
design of some rotors [Ter 87]. These rotors are larger-diameter inclusions so that contact be-
made from graphite and differ in the shape, the tween the gas bubble and the inclusion can occur
arrangement of the nozzles, as well as the rota- for flotation. In order to also remove fine inclu-
tion speeds. The nozzle shape and the rotation
ensure that fine gas bubbles are produced with
uniform distribution in the melt within the treat-
ment chamber.
The principle of the design of an in-line scav-
enging process (SNIF) is shown in Fig. 6.68
[Sze 78].
The design consists of a twin-chamber system
with two rotors. The melt passes through both
treatment chambers and flows out into a fore-
hearth, in which the melt turbulence is stabilized
so that it flows smoothly from the treatment
chamber in the direction of the casting plant. The
chamber volume of the in-line process is deter- Fig. 6.68 Schematic diagram of the in-line scavenging gas
mined by the necessary melt flow volume per (SNIF) system [Sze 78]
396 / Extrusion, Second Edition
processed per unit time. This again depends on mold wall and a low metal head in the mold is
the casting capacity, which is determined by the the ability to reliably control the metal head in
billet diameter and length, the number of billets, all molds in a multimold plant and to accurately
and the casting speed. For this reason, all sys- control the casting process. The cleaning costs
tems are designed so that they can be offered in and the demands placed on the casting personnel
any sizes to be able to match the casting capacity with these mold casting plants are considerable.
available in the continuous casting plant. These difficulties resulted in the development of
mold casting systems that enabled the use of ef-
6.11.4 Mold Casting Systems ficient short mold walls without the problems of
controlling the metal head. These mold casting
The main task of the casting mold technology systems for the production of extrusion billets
is the production of extrusion billets with a high- are described in this chapter, with reference to
quality surface and peripheral structure. There- some examples. The development of the hot-top
fore, the measures that must be fulfilled by the technology was a decisive step in improving the
mold technology are well known. Of particular casting technology for the casting of aluminum
importance is the reduction of the heat extraction extrusion billets [Ber]. The design concept of
through the mold wall, because this influences this mold system is shown by the example of a
the peripheral shell formation and depth. This hot-top mold type in Fig. 6.72 [Los 76].
can be achieved either by the use of a short ef- In this mold system, the metal feed and the
fective mold wall or by a low metal head in the metal head control in the form of an insulating
mold. In both cases, the method of metal feed attachment made from a refractory material,
into the mold and the control of the metal head known as the hot top, is placed over the mold.
are of great importance. The traditional contin- The effective mold wall is determined by the
uous casting system, which is still used today design and is not influenced by the metal feed.
for the casting of extrusion billets, is casting Therefore, uniformly short mold walls can be
with a nozzle and a float, as shown schematically realized for all molds in a multiple system. Hot-
in Fig. 6.71. top systems are distinguished by the shape of the
In this system, a cast iron or refractory ma- hot top used and the method of metal feed as
terial nozzle feeds the metal from the launder well as in the design of the cooling water system.
into the mold. The float, also made from refrac- Figure 6.73 shows two different hot-top shapes
tory material, controls the metal head in the and metal feed systems [Sch 89].
mold. The limitation of this system of a short The metal feed in the hot top is either from
the side at a constant level or centrally into the
hot top through a bore from the casting launder.
Fig. 6.71 Schematic arrangement of the continuous casting Fig. 6.72 Schematic arrangement of a hot-top casting mold
of aluminum alloys with a nozzle and a float for casting aluminum extrusion billets [Los 76]
398 / Extrusion, Second Edition
Fig. 6.73 Schematic arrangement of different hot-top molds and metal launders [Sch 88]
Figure 6.74 shows a modern mold casting plant further reducing the heat extraction through the
with constant-level metal feed from the casting mold wall. Mold systems that operate using this
launder. principle include the Airslip and the Airsol-veil
The separating agent necessary to minimize processes [Fan 84, Sch 88]. Whereas the Airsol-
the friction forces between the billet surface veil process uses metal mold walls, the Airslip
and the mold wall needed for a defect-free system uses mainly a porous graphite ring lo-
casting process is usually fed into the mold cated between the hot top and the metallic mold
wall under pressure between the mold and the wall parts, as can be seen in Fig. 6.75.
hot top. The mold wall separating agent and a mixture
A new generation of hot-top molds are the of argon and oxygen are fed through this porous
mold systems, that work with gas. In these sys- graphite ring. The supply and distribution of gas
tems, the mold wall is continually fed with a gas and separating agent is different in the Airsol-
as well as the separating agent, with the aim of veil process. This is shown in Fig. 6.76.
Fig. 6.74 Mold casting system with constant-level metal feed from the casting launder. Source: VAW-Elbewerk, Stade
Chapter 6: Machinery and Equipment for Direct and Indirect Hot Extrusion / 399
mold changing are simplified. The disadvantage Chamber furnaces or continuous homogeni-
is the space required. zation plants are used for the homogenization of
The arrangement and guiding of the casting aluminum extrusion billets. Stacks of billets are
table plays a decisive role in the straightness of used with the chamber furnaces, and these are
the extrusion billet, in particular, for casting moved into the oven and then cooled in a sepa-
lengths up to 8 m (26 ft). For guiding, the choice rate cooling chamber. The billets must be
is between rails and cylinder guiding. The inter- stacked to give almost uniform heating and cool-
nally guided nonrotating cylinder is being used ing of all billets. Often, specific billets are fitted
to an increasing extent because of its relatively with thermocouples to monitor the actual tem-
simple installation. The necessary resistance to perature cycle. Chamber homogenization plants
twisting is achieved by a relatively large cylin- consist of chamber furnaces, storage areas, and
der diameter. The casting table is mounted di- a transverse movable charging machine for the
rectly onto the cylinder ram. In rail guiding, the transport of the billet stacks. Figure 6.78 shows
guide rails are vertically located in the casting the schematic arrangement of a chamber ho-
pit. The machining and materials selection of the mogenizing plant. The chamber furnaces are
rails is critical. The so-called guide shoes are heated either electrically, indirectly with gas, or
located on the side of the casting table. The ear- by direct heating with hot gases. The cooling in
lier roller guide has been replaced by the guide
the cooling chamber is usually carried out with
shoe with synthetic fluorine-containing resin-
forced air.
coated guides. The rail guide requires accurate
installation and flat parallel machining of the In a continuous homogenization plant, the bil-
distortion-free guide rails. lets initially move one behind the other, follow-
Horizontal casting plants, developed origi- ing a preset cycle into a heating zone [Her 90]
nally for the casting of bus bars for electrolysis, where they are raised to the heat treatment tem-
are used today for casting extrusion billets in perature. They then pass through a holding zone
simple alloys for casting up to diameters of ap- before entering the cooling zone. Figure 6.79
proximately 200 mm. The casting plants avail- shows a continuous homogenization plant.
able can cast several logs but nowhere near as These plants offer advantages in the wide flex-
many as can be simultaneously cast with vertical ibility of billet cooling as well as a better
casting plants (Fig. 6.77). A restriction on billet consistency of the heat treatment and cooling
quality must also be taken into account. parameters. Large plants with production
Modern continuous casting plants are throughputs greater than 15,000 metric tons per
equipped with computer-based plant control sys- year are linked to casting plants so that the ex-
tems in which keyboards and computer screen trusion billets can be taken directly from the
displays are used to select and monitor the pro- casting pit to the homogenization plant via, for
cess parameters. In a further advance, a fully example, the intermediate stages of feed loading
automatic casting process including metal head table and inspection conveyor. Continuous ho-
control in the mold and casting launder using mogenization plants are heated electrically, and
capacitor or laser beam measurement systems is cooling is by forced air.
possible. This includes fully automatic furnace
tilting to control the desired constant metal head
in the casting system. These plant control sys-
tems enable the process parameters to be held
within narrow limits, producing a uniform and
reproducible billet quality. Equipment for the
6.11.6 Homogenization Plants
Production of Copper
Section 4.2 in Chapter 4 describes how ho- Billets
mogenization treatment is very important for the
subsequent processing of the extrusion billets Adolf Frei*
and the quality of the extruded sections pro-
duced from them. This requires accurate main- Trials and discussions on the continuous cast-
tenance of the temperature and the processing ing of metals were carried out approximately
time. Accordingly, the furnace for the homoge-
nization treatment must be designed to provide
controlled heating and cooling of the billets. *Systems for the Production of Copper Billets, Adolf Frei
Chapter 6: Machinery and Equipment for Direct and Indirect Hot Extrusion / 401
Fig. 6.77 Horizontal casting plant for casting aluminum ex- Fig. 6.78 Schematic design of a chamber homogenization
trusion billets. Source: Hertwich, Braunau, Austria plant [Her 90]
Fig. 6.79 Continuous homogenization plant for aluminum extrusion billets. Source: VAW-Elbeweke, Stade
150 years ago. However, the development of an decades the customary processes of casting in
industrially usable process was unsuccessful for sand or static molds used by semifinished prod-
a long time. uct plants had largely been superseded.
After initial work in the Vöhringen plant of A general overview of the development of the
Wieland-Werke AG, Ulm, Sigfried Junghaus is continuous casting process can be found in the
believed to have installed a plant in 1934 that literature [Swa 57, Hem 58, Hem 80, Kre 60].
was capable of withstanding the hard conditions
associated with casting in a semifinished product
plant. Although initially developed for brass, the
process was quickly extended to a wide range of 6.12 Plants with Furnace-Independent
copper alloys of various formats and to alumi- Molds
num alloys.
The new process brought so many advantages The important features of the process devel-
in terms of economy and quality that within two oped by Junghans are summarized in a 1933 pat-
402 / Extrusion, Second Edition
6.12.3 Molds
The mold in the casting of aluminum alloys
and copper alloys has basically the same task:
to act as the form-producing shape in the tran-
sition from the molten to the solid state. The
basic arrangement is therefore the same for both Fig. 6.83 Casting distributor for billets
alloy groups: indirect heat extraction through the
mold wall within the water-cooled mold, fol-
lowed by a more or less severe direct cooling of
the log with sprayed water or by feeding the log
into a water-filled pit.
The different properties of both alloy groups
require different mold formats. Whereas ex-
tremely short molds with lengths of 100 to 120
mm are used for aluminum alloys, molds be-
tween 250 and 400 mm are mainly used for the
casting of copper alloys. Sigfried Junghans orig-
inally used 900 mm long molds. Today, these
“long molds” are only used for casting copper
alloys that are very prone to stress cracking and
are unable to withstand direct water cooling.
Copper or CuCrZr is used as the mold mate-
rial, and sometimes, the mold surface on the log
side is hard chrome plated to reduce wear. Fig. 6.84 Casting distributor for slabs
404 / Extrusion, Second Edition
In 1936, S. Junghans investigated the contin- extrusion of aluminum alloys without lubrica-
uous casting of various aluminum alloys and tion. This friction is characterized by shearing
then steel. After a delay due to the war, he also of the billet from the material adhering to the
developed a convincing solution for steel con- container wall. With increasing friction dis-
tinuous casting that resulted in the installation placement or shear displacement, with increas-
of the first systems in metal working plants af- ing ram displacement, the temperature with
ter 1950 [Spe 56]. which the billet material enters the deformation
Today, the classic monoblock casting in static zone, E, increases if the initial billet tempera-
molds only has a minor role, even with steels. ture is approximately equal to the container tem-
Compared to copper alloys, the casting perature and the ram speed is constant.
speeds for steel are faster by a factor of 5 to In the deformation zone that forms in front of
10. Only in this way can the large quantities the die during the nonsteady processes at the
that must be cast be produced. The molds are start of extrusion, the material being deformed
1 to 1.5 m long, and the casting pipe extends undergoes a temperature increase, DU, corre-
over a meter down from the mold. The prop- sponding to the transformed work of deforma-
erties of steel enable the still-red-hot log to be tion. This results in the temperature with which
bent from the vertical to the horizontal and thus the material being deformed enters the die ap-
significantly saving on the plant building erture, MK, as the sum of the entry temperature,
height. This is favored by casting in a curved E, and the temperature increase in the defor-
mold from which the logs emerge at a down- mation zone, DU:
ward angle.
6.14.1 Influence of the Friction between should not be allowed to exceed a critical lim-
the Billet and the Container as iting value where transverse cracks can form on
well as the Deformation in the the extrusion.
Deformation Zone on the Depending on the magnitude of the tempera-
Temperature of the Extruded tures, the tensile stresses, and the flow stresses
in the external zones of the material being ex-
Material as It Enters the
truded, transverse cracks can form on the extru-
Die Aperture sion, and this should be avoided.
As already covered in Chapter 3, the container Die cooling can be used to avoid transverse
temperature is by no means constant over the cracks on the extruded section so that heat from
container length (see Fig. 3.19 in Chapter 3) and the extruded material preferentially flows from
changes in line with the intensity of the press the external zones of the extruded product into
production [Ake 71] (see Fig. 3.20 in Chapter the colder die.
3). This effect is more pronounced the slower the
If the initial billet temperature, B, is equal to extrusion flows through the die aperture; for ex-
the container temperature, R, and is constant ample, the slower the extrusion speed, the
over the billet volume, and if the stem speed is greater the heat that can flow from the extrusion
constant over the stem displacement, then there into the colder die. Die cooling should be con-
is an increase in the temperature with which the sidered, in particular, for the alloy types Al-
material being extruded enters the deformation ZnMgCu, AlCuMg, and AlMg (see Fig. 5.21 in
zone, E, over the stem displacement, due to the Chapter 5).
friction between the billet and the container Liquid nitrogen has proved successful in prac-
wall. The temperature E increases with increas- tice as the cooling medium. This is supplied be-
ing stem displacement, that is, with increasing hind the die so that it provides both die cooling
friction path covered. and cooling of the section as it leaves the die
As the material being extruded crosses the de- into a protective gaseous atmosphere.
formation zone, it undergoes a temperature in- Depending on the alloy, this allows recrystal-
crease, E, corresponding to the conversion of lization to be retarded in the external zone of the
the deformation work into heat. This falls extruded section as it leaves the die. Cooling of
slightly with increasing stem displacement be- the die and the extruded section gives higher ex-
cause of the decrease in the flow stress in the trusion speeds and better surface quality and
deformation zone resulting from the higher tem- therefore higher productivity with a better prod-
perature of the billet volume entering the defor- uct quality (see also the section “Heat Removal”
mation zone. in Chapter 5).
However, the influence of the friction be-
tween the billet and the container dominates so 6.14.3 Measurement of the
that the temperature MK of the material being
Extrusion Temperatures
deformed increases as it enters the die aperture
(see Fig. 3.22 in Chapter 3). The determination of the temperatures of the
material being extruded as it enters and leaves
the die aperture and as it enters the downstream
6.14.2 Heat Transfer in the Die Area
cooling system plays an important role in the
As the material being extruded passes through reproducible trouble-free and economic extru-
the die aperture, the external zones of the ex- sion of a defect-free product.
truded section increase in temperature as a result As shown in Fig. 3.23 in Chapter 3, it is pos-
of the friction with the die bearings. Tensile sible with microsheathed thermocouples to mea-
stresses in the external zones also form when sure the temperature at the leading edge of the
there are compressive stresses in the interior of die aperture. This process is very reliable and
the extrusion. The heating of the external zones accurate. It is useful for calibrating radiation
of the extrusion reduces the flow stress. pyrometers, for the measurement of the tem-
Taking into account the tensile stresses and peratures at which transverse cracking on the ex-
the flow stresses in the external zones of the ex- truded product occurs, and for verifying theo-
truded product as well as the compressive retical models on the thermal changes in the
stresses and higher flow stresses inside the ex- process. It is, however, too complex for produc-
trusion, the temperature in the external zones tion. Between 1980 and 2000, radiation pyrom-
408 / Extrusion, Second Edition
eters were developed, but there are problems as- ● Axial initial billet temperature profile, with
sociated with the accuracy of the measured a decreasing temperature from the front to
temperature because of the low emissivity of the back of the billet
aluminum alloys. A combination of a ratio py- ● Ram speed as a function of the ram displace-
rometer with a fixed-wavelength pyrometer [Yao ment, for example, the ram speed decreases
91] [Rep 94] as well as a full-spectrum pyrom- with increasing ram displacement
eter are known [Pan 95]. It is also possible to ● Zone heating and zone cooling of the con-
measure the radiation intensity in several spec- tainer, with the aim of maintaining the tem-
tral regions [Yao 91] [Pan 95] [Sch 94]. perature fields of the container constant, in-
It is particularly difficult to accurately deter- dependent of the intensity of the press
mine the temperature of the surface of the extru- operation
sion. It is possible to directly measure the tem- The results of these measures must be that the
perature of the surface using thermocouples and temperature E of the billet material is constant
to use this to calibrate the radiation pyrometer. over the ram displacement as it enters the de-
In this way, it is possible, as described in formation zone; for example, the heating of the
Schiewe [1994], to collect emissivity data for billet from the friction with the container must
the application of a four-channel pyrometer by be compensated. Therefore, the temperature
measuring the surface temperature of the ex- field of the container should not change as a
truded product with a surface thermocouple function of the intensity of the press operation
probe. during extrusion. Zone heating and zone cooling
are now standard technology.
However, if the temperature field of the con-
6.14.4 Methods of Achieving Constant tainer does change, then the ram speed over the
Exit Temperatures over the Length ram displacement and the axial temperature pro-
of the Extrusion or Ram file of the billet can be adjusted accordingly.
Displacement in the Direct Hot The intention should be to ensure that the ma-
Extrusion of Aluminum Alloys terial being extruded always enters the defor-
As already discussed in Chapter 3, the follow- mation zone with a constant temperature E. If
ing possible methods can be used to achieve as one or a combination of the measures described
near as possible a constant exit temperature over previously are used to successfully keep E con-
the extruded length. They are not usually used stant over the ram displacement, then the exit
alone but in combination: temperature, S, will be higher than the entry
temperature by DU, which is the heat generated
● Optimization of the difference between the in the deformation zone, but constant over the
initial billet temperature and the container ram displacement or the length of the extrusion
temperature (Fig. 6.87).
Fig. 6.87 Desired exit temperature variation over the length of the extrusion or the stem displacement in the direct hot extrusion
without lubrication of aluminium alloys
Chapter 6: Machinery and Equipment for Direct and Indirect Hot Extrusion / 409
Fig. 6.89 Variation in the exit temperature over the stem displacement [Rup 75]
410 / Extrusion, Second Edition
indirect extrusion. With a constant ram speed sistance heating and, when needed, zone cooling
over the ram displacement the material being de- have proved successful in practice. A constant
formed enters the deformation zone that forms container temperature over the container length
during the unsteady start of the extrusion pro- would be ideal.
cess, always with the same temperature, E, if
the initial billet temperature, B, is the same as
the container temperature, R.
In the deformation zone, the material being
extruded undergoes a temperature increase,
DU, which is constant over the ram displace- Process Control Concepts
ment after the unsteady start of the extrusion
process, corresponding to the deformation work
for Extrusion Plants
required. Then, according to Eq. 6.6, the exit
temperature, S, must be constant over the Armit Biswas*
length of the extrusion or the ram displacement.
For the quasi-stationary deformation process The productivity of a modern extrusion plant
(see Fig. 3.50 in Chapter 3): is influenced by a wide range of different factors.
The process control has the task of reconciling
S ⳱ E Ⳮ DU ⳱ constant (Eq 6.6) the individual production stages with each other.
This should produce a product that meets the
where requirements of the customer. The priorities can
vary considerably. The quality requirements in
B ⳱ R ⳱ E and uSt ⳱ constant (Eq 6.7) terms of surface finish, mechanical properties,
and dimensions of the section can be rigorous or
The profile shown in Fig. 6.87 for the set tem- not, depending on the specific customer require-
perature over the length of the extrusion or the ments. The process optimization must deal with
ram displacement can thus be achieved without the changing requirements to achieve the max-
any special measures, for example, special ram imum throughput while maintaining the quality
speed profile over the ram displacement and/or specified.
special initial billet temperature variation over
the billet length.
In indirect hot extrusion, the billet length is 6.16 Electrical-Electronic Control
only limited by the buckling length of the hollow
stem. Initial billet lengths of five to eight times Control and data collection on extrusion
the billet diameter are possible in indirect hot presses plays a special role in the overall plant
extrusion. With these initial billet lengths, air re- system. They form the basis for optimization for
moval during upsetting of the billet in the con- product quality, quality control, as well as the
tainer can be a problem. It is therefore advisable optimal utilization of the extrusion plant. This
to have a temperature profile in the billet so that section describes the current state of the tech-
the front of the billet is the hottest and the tem- nology.
perature decreases toward the back end of extru- The extrusion process determines the type of
sion. The upsetting process then takes place press. The press movements are coordinated by
from the front to the back, enabling the trapped the electrical control system, which uses sensors
air to be released without any problem. and hydraulic and electrical components as the
As described in sections 6.3.1.4 and 6.3.1.5, operating elements.
a billet axial temperature profile is possible with The plant operator has the task of monitoring
induction billet heating. the extrusion process. He should always be able
The container can give additional problems. to access the current production process and, if
If the container is only fitted with induction heat- necessary, change the press parameters. This re-
ing, then there are axial temperature profiles quires a suitable visualization system that is also
along the container wall, with a maximum value realized by the electronic control.
in the middle of the container and minimum at
the container ends because of the cooling of the
end faces (see Fig. 3.19 in Chapter 3). Combi- *Process Control Concepts for Extrusion Plants, Armist Bis-
nations of induction heating combined with re- was
Chapter 6: Machinery and Equipment for Direct and Indirect Hot Extrusion / 411
A data collection system collects all the rele- ● A production planning system on the top
vant process data and evaluates them. It should level that is specifically configured for the
cover not only the actual data from the press but requirements in the extrusion plant
also from the auxiliary equipment (e.g., fur-
naces, run-out, stretcher saw). The data collec- The PLC system coordinates the sequential
tion system can also store optimized process pa- movement of the plant components. The data
rameters for specific orders and make them input for the entire process is enabled by this
available for future orders as well as passing system. Software routines for fault diagnostics
them on to affiliated systems (Fig. 6.90). and defect evaluation are also included. It is
The role of the maintenance personnel is to linked to the higher-level processing system.
optimize the plant availability. They require a The extrusion speed and the extrusion pressure
meaningful fault detection system to be able to are digitally controlled by the system. With cop-
select the suitable corrective measures to be per alloy presses, the PLC system also controls
taken. the coiler.
Control technology, visualization, process The interface for the visualization and the op-
control technology, process planning, and main- timization is a man-machine interface supplying
tenance support are central components of the information to the operator and the maintenance
process control system and contribute to ensur- personnel. It is also linked to the central data
ing the product quality and to the increase in processing system. This system enables the con-
productivity of the complete plant. trol of the furnace and the press as well as all
An example of a hierarchical control system the downstream equipment. All relevant data are
could be structured as: displayed on screens and control desks. Changes
● Programmable logic control (PLC) system in the default data can be entered by a keyboard.
on the lowest level that controls the machine Software for the optimization of the actual ex-
● Then an interface that collects the relevant trusion process can be linked to the control sys-
data, visualizes process relationships, and tem. The production planning system contains
optimizes die-specific optimal process data. It enables the
● Followed by process technical software in production of a press order with order-related
which the extrusion process is optimized data (e.g., type of section, length, quantity). The
both qualitatively and quantitatively production of reports with statistical data (e.g.,
Fig. 6.90 Schematic arrangement of a data collection system for an extrusion press
412 / Extrusion, Second Edition
shift, daily, monthly, annual reports) is also pos- ● Possibility of container cooling, and the lo-
sible. cation of the cooling zones
The advantages of such a system are obvious ● Location and number of thermocouples in
[Schü 96].The most important advantages are: the container to control the heating and cool-
ing zones
● System enables fast and direct information ● Possibility of fine continuous adjustment of
flow, and a central point can control all pro- the extrusion speed
cess procedures. ● Die design
● Automatic control of all processes gives
● Die temperature
quality control as well as continuous quality ● Dummy block temperature
and production monitoring. ● Sealing tool or sealing stem temperature in
● All areas involved in the production process
indirect extrusion
can exchange information with each other. ● Quality of the data-monitoring system
● Historic information can be extracted from
the data bank at any time.
6.16.2 Improvement in the
6.16.1 Factors that Influence the Productivity and Product Quality
Productivity and Quality of the by the Optimization of the
Products in the Extrusion Process Extrusion Process
The following factors influence the productiv- Influencing the extrusion process by on-line
ity and quality of the products in the extrusion control of the container temperature can be ex-
process: cluded, because the temperature of the container
cannot be changed quickly enough. However,
● Initial billet temperature and the radial and the axial temperature distribution in the con-
axial temperature profiles tainer can be held to a more or less uniform level
● Time for the transport of the billet from the by suitable heating and cooling systems, which
furnace to the loader ensures that this state remains thermally stable.
● Dwell time in the billet loader The practical variables for the optimization of
● Mean container temperature and temperature the extrusion process are the initial billet tem-
distribution perature and the extrusion speed. Some im-
● Thermal capacity of the container (mass of provement can naturally be achieved by a trial-
the container) compared to the thermal ca- and-error method.
pacity of the billet However, greatly simplified finite element
● Number and location of the heating elements process simulation programs offer the possibil-
in the container, and the ability to switch in- ity of determining the initial billet temperature
dividual heaters on and off profile and/or the ram speed profile for a given
Fig. 6.91 Press cycle time reduction with a computer-based control system. Statistic evaluation of the results of 1300 dies in 10
different extrusion plants
Chapter 6: Machinery and Equipment for Direct and Indirect Hot Extrusion / 413
container temperature field, so that a predeter- [Ber]: W.I. Bergmann, U.S. patent 298,3972
mined exit temperature is obtained after the un- [Bet 39]: I.O. Betterton and F.F. Poland, Vorri-
steady initial extrusion process. chtung zum kontinuierlichen (System for
A statistical study of the extrusion time re- Continuous Casting of Metals), U.S. patent
ductions that can be obtained from a simulation 2264,488, Gießen von Metallen, 1939–1951
process is shown in Fig. 6.91 [Rep 96a]. The [Bis 66]: A. Biswas and A. Steinmetz, Rechner-
evaluation is based on the results of approxi- ische Simulation des Strangpreßvorganges
mately 1300 dies in 10 different extrusion (Computer Simulation of the Extrusion Pro-
plants. Comparable evaluations for iterative cess), Aluminum, 1966
learning programs that operate with the exit tem- [Bis 80]: A.K. Biswas and W.G. Davenport, Ex-
perature measurement are not yet available. tractive Metallurgy of Copper, 2nd ed., Per-
gamon Press, Oxford, 1980, p 339–343
[Bis 89]: A. Biswas and A. Steinmetz, “Re-
REFERENCES chnerische Simulation des Strang-
preßvorganges,” Vortrag auf dem Symposium
[Ake 68]: R. Akeret, Untersuchengen über das Strangpressen der DGM (“Computer Simu-
Strangpressen unter besonderer Berücksichti- lation of the Extrusion Process,” Papers at the
gung der thermischen (Investigations into Ex- Symposium on Extrusion of the DGM), 1989
trusion with Specific Reference to the Ther- [Bis 92]: A. Biswas, B. Repgen, and A. Stein-
mal Processes), Vorgänge 5, Int. metz, Computer Simulation of Extrusion
Leichtmetalltagung (Int. Light Alloy Confer- Press Operation, Experience with CADEX, a
ence), Leoben-Wien, 1968, p 304–307 New Computer Aided Process Optimizing
[Ake 71]: R. Akeret, Die Produktivität beim System, Proceedings, Fifth International Alu-
Strangpressen von Aluminumwerkstoffen— minum Extrusion Technology Seminar, Vol II,
Einfluß von Werkstoff und Verfahren (The 1992, p 149–155
Productivity in the Extrusion of Aluminum
[Bri 96]: R. Brioschi, “New Technology in Ex-
Alloys—Influence of Material and Process),
trusion Presses Design,” International Alu-
Z. Metallkd., Vol 62 (No. 6), 1971, p 451–456
minum Extrusion Technology Seminar (Chi-
[Ake 80]: R. Akeret, Das Verhalten der Strang-
cago, IL), 1996
presse als Regelstrecke (The Extrusion Press
[Bro 80]: J. Broichhausen and F.U. Heute, Ge-
as a Controlled System), Z. Metallkd, Vol 34
(No. 8), 1980, p 737–740 kühltes Strangpressen von Schwermetallen
[Ant 77]: E.J. Anthofer, “Press Alignment,” (Coded Extrusion of Copper Alloys), Z. Me-
Second International Aluminum Extrusion tallkd., Vol 34 (No. 1), 1980, p 40–44
Technology Seminar, 1977 [Buc]: Iterativ lernende Regelung für zyklische
[Ape 80]: D. Apelian and R. Mutharasan, J. Systeme (Iterative Learning Control and Cy-
Met., Vol 32 (No. 9), 1980, p 14–19 clic Systems), VDI-Verlag, Düsseldorf
[Ape 85]: D. Apelian, C.E. Eckert, R. Muthar- [Bug 88]: J.C. Bugai, “CIEM: Computer Inte-
asan, and R.E. Miller, Proc. Refining and Al- grated Extrusion Manufacturing,” Fourth In-
loying of Liquid Aluminum and Ferro Alloys, ternational Aluminum Extrusion Technology
The Norwegian Institute of Technology, Seminar (Chicago, IL), 1988
Trondheim, Aluminum Verlag, Düsseldorf, [Des 89]: T. Desmoulins, H. d’Hondt, J.M. Hic-
1985, p 123–143 ter, and P. Netter, Light Met., 1989, p 757–
[Asa 84]: A. Asari, T. Noyori, and M. Ueda, 767
Recent Technology of Indirect Extrusion, [Dor 90]: J.E. Dore, Light Met., 1990, p 791–
Third International Aluminum Extrusion 796
Technology Seminar (Atlanta, GA), 1984 [Edw 92]: J.A. Edwards, “Automatic Handling
[Bai 58]: R. Baier (Asarco), Pouring Technique Systems and New Equipment for Heavy-Duty
for Continuous Casting, U.S. patent Extruding,” Fifth International Aluminum
3,066,364, 1958–1962 Extrusion Technology Seminar (Chicago, IL),
[Bam 90]: J. Baumgarten, EDV-gestützte Instan- 1992
dhaltung und Schwachstellenanalyse (Com- [Ell 88]: L.D. Elliot, “Optimation—Not Nec-
puter Based Maintenance and Weakpoint essarily Automation,” Fourth International
Analysis), G. Jung, Ed., Strangpressen, DGM- Aluminum Extrusion Technology Seminar
Informationsgesellschaft m.b.H., 1990, p 99 (Chicago, IL), 1988
414 / Extrusion, Second Edition
[Eng 91]: T. Engh, F. Frisvold, and S.T. Johan- [Jun 84]: K. Junge and R. Jeschar, Gas-Wärme-
sen, Continuous Casting DGM—Information Int., Vol 33, 1984, p 371–380
Society, Oberursel, 1991 [Kra 83]: H.A. Krall, Metall, Vol 37, 1983, p
[Fau 84]: J.P. Faunce, F.E. Wagstaff, and H. 466–471
Shaw, Light Met., 1984, p 1145–1158 [Kre 60]: H. Kreil, H. Vosskühler, and K. Wal-
[Fis 97]: G. Fischer, Von der Qualitätssicherung ter, The Continuous Casting of Copper and Its
zu Business Excellence (From Quality Control Alloys, Metall. Rev., Vol 5, 1960, p 413–446
to Business Excellence), K. Schimmelpfen- [Lec 79]: G.B. Leconte and K. Buxmann, Alu-
nig, Ed., Strangpressen, DGM-Informations- minum, Vol 55 (No. 6), 1979, p 387–390
gesellschaft, Verlag, 1997, p 179 [Loh 89]: T. Lohikoski and M. Lohikoski, Me-
[Gär 80]: H. Gärtner, Temperaturmodell einer tall, Vol 43, 1989, p 531–533
Strangpresse (Temperature Model of an Ex- [Los 76]: E. Lossack, Light Met., 1976, p 413–
trusion Press), Technischer Bericht, Schloe- 424
mann-Siemag AG, 1980 [Mar 88]: M.A. Marchese and J.J. Coston, “Ef-
[Ger 96]: H. Gers, Theoretical and Practical ficient Use of Liquid Nitrogen for Aluminum
Consideration for the Application of “Fuzzy Extrusion Die Cooling and Inerting,” Fourth
Logic” in the Aluminum Extrusion Industry, Inernational Aluminum Extrusion Technol-
Proceedings Sixth Int. Aluminum Extrusion ogy Seminar (Chicago, IL), 1988
Technology Seminar, Vol 1 (Chicago IL), [Mül 59]: E. Müller, Hydraulische Pressen und
1996, p 51–55 Druckflüssigkeitsanlagen (Hydraulic Presses
[Hem 58]: E. Herrmann, Handbuch des Strang- and Accumulation Systems), 3rd ed.,
gießens (Continuous Casting Handbook), Springer-Verlag, 1959
Düsseldorf, Aluminum Verlag GmbH, 1958 [Nef 93]: D.V. Neff, Light Met., 1993, p 805–
[Hem 80]: E. Herrmann, Handbook on Contin- 812
uous Casting, Düsseldorf, Aluminum Verlag [Neu 97]: R. Neugebauer, “Steuerung und Da-
GmbH, 1980 tenerfassung an LM-Strangpressen,” Vortrag
anläßlich der SMS-Pressentagung (“Control
[Hen 80]: A.J. Hengemolen, “Aluminum Indus-
and Data Collection on Aluminum Extrusion
try Energy Conservation Workshop V Papers”
Press,” Paper at the SMS Press Conference),
(Washington D.C), Sept 1980, p 93–104
Leverkusen, 1997
[Hen 83]: A.J. Hengemolen and R. Moser, Alu-
[Out 85]: Prospekt “Upcast,” Outokumpu In-
minum, Vol 59, 1983, p 516–521, 602–605 dustrial Equipment Division, 1985
[Her 90]: G. Hertwich, Strangpressen (Extru- [Pan 95]: M. Panduit and K. Buchheit, Isoth-
sion), DGM—Information Society, Oberur- ermes Strangpressen von Aluminum (Isother-
sel, 1990 mal Extrusion of Aluminum), Z. Alum., Vol
[Höl 88]: H. Höller, “Experience with the Au- 71, 1995, p 483–487, 614–619
tomated Press Line of Hydro Aluminium [Pan 96]: M. Pandit and K. Buchheit, A New
Nenzing,” Fourth International Aluminum Measurement and Control System for Iso-
Extrusion Technology Seminar (Chicago, IL), thermal Extrusion, Proceedings: Sixth Inter-
1988 national Aluminum Extrusion Technology
[Hue 92]: P. Van Hue, “Heat Transfer Model for Seminar, Vol 1, 1996, p 79–86
Temperature Profile of Extruded Sections at [Pas 84]: J.A. Passeri, Proc. of Third Interna-
the Extrusion Press Exit,” Fifth International tional Aluminum Extrusion Technology Sem-
Aluminum Extrusion Technology Seminar inar, Vol 1 (Atlanta, GA), April 1984, p 149–
(Chicago, IL), 1992 151
[Iwa 84]: M. Iwata, “Extrusion Press Control by [Put 71]: J. Putz, Moderne Blockanwärmanla-
Microcomputer Assistance and Automatic gen (Modern Billet Heating Plants), Z. Me-
Billet Handling System,” Third Aluminum tallkd., Vol 62, 1971, p 21–26
Extrusion Technology Seminar (Atlanta, [Put 83]: J. Putz, Gasschnellanwärmofen für
GA), 1984 Preßbolzen mit Hubbalkentransport (High
[Jas 86]: H. Jasper, Gas-Wärme-Int., Vol 35, Speed Gas Fired Billet Furnaces with Walking
1986, p 136–140 Beam Transport), Metall, Vol 37, 1983, p
[Jug 33]: S. Junghans, Verfahren und Vorri- 451–454
chtung zum Gießen von Metallsträngen (Pro- [Put 87]: J. Putz, Preßbolzenanwarmöfen (Billet
cess and Equipment for Casting Metal Logs), Heating Furnaces), Metall, Vol 41, 1987, p
DRP 750, 301, 1933–1945 371–381
Chapter 6: Machinery and Equipment for Direct and Indirect Hot Extrusion / 415
[Rei 80]: W. Reinke and K. Alker, Aluminium, metalltagung (Int. Light Alloy Conference),
Vol 55, 1980, p 383–387 Leoben-Wien, 1981, p 294–295
[Rep 89]: B. Repgen, “Untersuchung zur Pro- [Rup 95]: D. Ruppin, Temperaturführung beim
duktionsoptimierung beim Isothermen direkten Strangpressen von Aluminumlegi-
Strangpressen” (“Investigation into Produc- erungen, Grundlagen des Strangpressens
tion Optimization in Isothermal Extrusion”), (Temperature Control in the Direct Extrusion
Diplomarbeit, Inst. für bildsame Formgebung, of Aluminum Alloys, Principles of Extru-
R.W.T.H., Aachen, 1989 sion), K. Herausgegeben von Müller, Ed.,
[Rep 94]: B. Repgen, “Möglichkeiten der Kontakt & Studium, Bd. 286, Expert Verlag,
Prozeßoptimierung beim direkten Strangpres- 1995
sen von Aluminiumlegierungen,” Seminar [Saa 93]: A. Saavedra, Light Met., 1993, p 739–
Grundlagen des Strangpressens (“Potential 743
for Process Optimization in the Direct Extru- [Sch 89]: W. Schneider and E. Lossack, Proc.
sion of Aluminum,” Basics of Extrusion Sem- New Developments in Metallurgical Process-
inar), T.A. Eßlingen, 1994 ing, Vol 2, Verein Deutscher Eisenhüttenleute,
[Rep 96a]: B. Repgen and V. Rothweiler, Er- Düsseldorf, 1989
fahrung mit dem Einsatz einer [Sch 88]: W. Schneider and E. Lossack, Metall,
Prozeßoptimierung für das Strangpressen Vol 42 (No. 2), 1988, p 124–128
(Experience with the Application of Process [Sch 94]: W. Schneider, Light Met., 1994, p
Optimization for Extrusion), Aluminum, Vol 985–989
72, 1996, p 868–870 [Sch 94]: C. Schiewe, Pyrometrische Tempera-
[Rep 96b]: B. Repgen and A. Biswas, Isother- turmessung beim Aluminum-Strangpressen
mal and Isopressure Extrusion—Results of (Temperature Measurements with Pyrome-
Process Optimization in Various Extrusion trics in Aluminum Extrusion), Metall, Vol 48,
Plants, Proceedings Sixth International Alu- 1994, p 628–632
minum Extrusion Technology Seminar, Vol I [Schl 89]: D. Schluckebier, Induktive Blocker-
(Chicago, IL), 1996, p 37–43 wärmung (Induction Billet Heating—Extru-
[Rog 96]: A.P. Roger, “How to Operate Extru- sion Billets), Extrusion Symposium DGM,
sion Presses Well . . . ,” International Alu- 1989, p 87–98
minum Extrusion Technology Seminar (Chi- [Scho 76]: H.E. Scholz, “Werkstoffkundliche,
cago, IL), 1996 experimentelle und theorethische Untersu-
[Rot 84]: W. Roth, Aluminum, Vol 60, 1984, p chungen zur Optimierung des Strangpressens
249–250 metallischer Werkstoffe” (“Material Scientific
[Rup 75]: D. Ruppin and W. Strehmel, Axiale Experimental and Theoretical Investigation
Temperaturprofile in Strangpressbolzen aus into the Optimization of the Extrusion of Me-
Aluminumwerkstoffen (Axial Temperature tallic Materials”), Dissertation, R.W.T.H., Aa-
Profiles in Extrusion Billets in Aluminum Al- chen, 1976
loys), Aluminum Sonderdruck aus dem, Vol [Schü 96]: K.H. Schütte, Neue Modernisierung-
51 (No. 9), 1975, p 585–588 skonzepte für Strangpreßanlagen (New Mod-
[Rup 77]: D. Ruppin and W. Strehmel, Direktes ernization Concept for Extrusion Plants), Alu-
Strangpressen mit konstanter Austrittstemper- minum, Vol 72, 1996, p 468–474
atur-Einsatz variabler Pressgeschwindigkeit [SMS]: Das CADEX Software Programm (The
(Mitteilungen der Forschungsgruppe Strang- CADEX Software Program), SMS-Hasen-
pressen an der Technischen Universität Ber- clever-Schrift, p 2–314
lin) (Direct Extrusion with Constant Exit [Spe 56]: K. Speith and A. Bungeroth, Stahl Ei-
Temperature-Application of Variable Extru- sen, Vol 76, 1956, p 437–442
sion Speed), Aluminum, Vol 53, 1977, p 233– [Ste 91]: A. Steinmetz and W. Staschul, Strang-
239, 543–548, 674–678, 773–776 und Rohrpressen von Kupfer und Messing
[Rup 81]: D. Ruppin and K. Müller, Tempera- (Rod and Tube Extrusion of Copper and
turverhaltnisse beim direkten Strangpressen Brass), Metall, Vol 45 (No. 11), Nov 1991
von Rohren aus Aluminum-Legierungen über [Str 96]: W. Strehmel, M. Plata, and B. Bourqui,
stehenden und mitlaufenden Dorn (Tempera- “New Technologies for Cooling and Quench-
ture Variation in Direct Extrusion of Alumi- ing of Medium-to-Large-Sized Aluminum
num Alloy Tubes over Fixed and Moving Extrusions,” International Aluminum Extru-
Mandrels), Tagungsbericht der 7, Int. Leicht- sion Technology Seminar (Chicago, IL), 1996
416 / Extrusion, Second Edition
[Stre 82]: W. Strehmel, “Untersuchungen zum Seminar, Vol 1 (Atlanta, GA), Nov 1977, p
rechnergestützten direkten Strangpressen von 81–86
Aluminum-Legierungen,” Fortschrittsberi- [War 85]: M.E. Ward, Adv. Ceram. (Ceram.
chte VDI-Z, Reihe 2 (“Investigations into Heat. Exch.,) Vol 14, 1985, p 71–77
Computer Controlled Direct Extrusion of [Wie 83]: J.J. Wiesner, Aluminum, Vol 59, 1983,
Aluminum Alloys,” Progress Report, VDI-Z, p 493–496
Series 2), No. 51, VDI-Verlag GmbH, Düs- [Wil 51]: H. Wieland, Verfahren zum Strang-
seldorf, 1982 gießen metallischer Werkstoffe (Process for
[Stt 96]: B. Steinert, Einflußmöglichkeiten zur Continuous Casting of Metallic Materials),
optimalen Werkzeugabstützungn in Leicht- DBP 892, 230, 1951–1953
metall-Strangpressen (Possible Methods for [Yao 91]: Ch. Yao, “Isothermes direktes Strang-
Achieving Optimum Tool Support in Alumi- pressen von Aluminumlegierungen” (“Iso-
num Extrusion), Sonderdruck aus Aluminum, thermal Direct Extrusion of Aluminum Al-
loys”), Dissertation, Berlin, 1971
Vol 72, (No. 5), 1996
[Yok 77]: H. Yokobayashi, T. Chiba, and J. Mo-
[Swa 57]: W. Schwarzmeier, Stranggießen
rooka, “Study of the Indirect Extrusion Pro-
(Continuous Casting), Stuttgart, Berliner cess of Aluminum Alloy,” Second Interna-
Union GmbH, 1957 tional Aluminum Extrusion Technology
[Sze 78]: A.G. Szekely, Erzmetall, Vol 31 (No. Seminar, 1977
3), 1978, p 110–117 [Zie 73]: W. Ziegler and K. Siegert, Indirektes
[Ter 87]: S. Terai and M. Yoshida, Proc. Eight Strangpressen von Leichtmetal (Indirect Ex-
Int. Light Alloy Conference, Leoben-Wien, trusion of Aluminum), Z. Metallkd. Vol 64
1987, p 236–243 (No. 4), 1973, p 224–229
[Thu 84]: F. Thurnheer, “Automated Extrusion [Zil 84]: F.-J. Zilges, Aufbau und Arbeitsweise
Plants Come of Age in Europe,” Third Inter- einer neuen Indirekt-Strang-und Rohr-
national Aluminum Extrusion Technology preßlinie für Aluminum (Design and Opera-
Seminar (Atlanta, GA), 1984 tion of a New Indirect Rod and Tube Extru-
[War 77]: O.H. Warwick, Proc. of Second In- sion Line), Sonderdruck aus Aluminum, Vol
ternational Aluminum Extrusion Technology 60 (No. 6), 1984
Extrusion: Second Edition Copyright © 2006 ASM International®
M. Bauser, G. Sauer, K. Siegert, editors, p 417-549 All rights reserved.
DOI:10.1361/exse2006p417 www.asminternational.org
CHAPTER 7
Extrusion Tooling
Günther Sauer and Adolf Ames*
*Tools for the Extrusion of Materials with Deformation Temperature of 600 to 1300 ⬚C, Martin Bauser
Recent Developments in Resistance Heating of Containers, Wolfgang Eckenbach
Static- and Elastic-Based Analysis and Dimensioning of Containers Loaded in Three Dimensions, Günther Sauer
Hot Working Materials for the Manufacture of Extrusion Tooling, Günther Sauer
418 / Extrusion, Second Edition
● Be produced from hot working material with wear in the shape-forming aperture of an extru-
adequate temperature resistance sion die has an unfavorable effect on the quality
● Exhibit a high functional efficiency of the surface of the extrusion, the abrasive wear
● Offer a favorable price/throughput ratio leads to shape and dimensional inaccuracies of
the cross section of the extrusion. In the ad-
Auxiliary tooling and support tooling must: vanced stage, both types of wear can seriously
impair the extrusion of sections to final sizes or
● Be dimensioned so that the shape-producing even make it impossible. This gives rise to the
regions of the extrusion tooling undergo only need to reduce the adhesion and abrasion as far
insignificant elastic deformation under the as possible, for example, by lubrication, or by a
extrusion loads, ensuring that material flow thermochemical surface treatment such as pe-
and shape are not negatively influenced ripheral layer formation by nitriding, or by the
deposition of wear-resistant surface coatings by
7.1.2 Requirements of the the chemical vapor deposition process. Die and
mandrel inserts in hot working materials that can
Tooling Materials
withstand higher thermal stresses can also be
Depending on the billet material, the materials used.
for extrusion tooling are more or less highly Depending on the deformation temperature,
stressed, both thermally and mechanically. With significant operating temperatures can develop
fast extrusion cycles, the associated high ther- on the working surfaces of the extrusion tooling.
momechanical stressing can be considered as Suitable hot working materials and application-
continuous loading, and with slow extrusion cy- specific heat treatments are needed to ensure
cles, as interrupted creep loading, as discussed long tooling service life. The property require-
in more detail in section “Hot Working Materials ments for a material suitable for the manufacture
for the Manufacture of Extrusion Tooling” in of extrusion tooling are:
this chapter. The highest thermomechanical
stressing is found in the tooling areas that come ● Temperature resistance combined with opti-
into direct contact with the billet material heated mal values for creep and fatigue strength in
to the deformation temperature. Friction and the operating temperature range
shear stresses occur in the thermomechanically ● Hot toughness
stressed contact areas of the tooling as well as ● Hot wear resistance to abrasion and adhesion
the deformation forces. Friction and shearing in ● Resistance to temperature fluctuations
the container and on the working surfaces of the ● Thermal conductivity
shape-producing tools can have a significant ef- ● Resistance to chemical reaction with the ex-
fect on the total extrusion load, depending on truded material
the material being extruded. In direct extrusion
without lubrication, the friction and shear forces In the stress collective of a tribosystem, a re-
can be up to 60% of the total extrusion load. active body always moves against a reaction
Wear and adhesion at the tool working surfaces body [Gah 90, Bun 81, Hab 80, Bre 79]. The
render the tooling unusable in the medium and tribological system between the working sur-
long term. faces of the extrusion tooling and the billet ma-
Friction and wear at the working faces of the terial has the tooling as the reaction body and
extrusion tooling and the desire to minimize continuously changing extruded material result-
them enable the sliding partners of the billet ing from the deformation-related material flow
material/tooling to be considered as a tribosys- as the reactive body.
tem. There are hardly any selection options be- The extrusion tooling is deformed elastically
cause of the deformation function of the extru- during the extrusion process, and the extruded
sion process, but process-specific dry friction material plastically. During the deformation by
with unlubricated direct extrusion, boundary, extrusion, the following tribological conditions
and mixed friction in extrusion with lubrication between the extrusion tooling as the reaction
as well as liquid friction in hydrostatic and lu- body and the billet material as the reactive body
bricated extrusion can occur. must be taken into account:
Sliding wear occurs on the tool working sur-
faces and mainly consists of abrasive and ad- ● At the working surfaces, an effective normal
hesive wear. For example, whereas the adhesive force as the contact force
Chapter 7: Extrusion Tooling / 419
● Temperatures developed at the working sur- 7.2 Design of Tool Sets for
faces Direct and Indirect Extrusion
● Flow rate of the extruded material at the
working surfaces and, if necessary, the oc- In direct extrusion, the tool set for the pro-
currence of deformation-related relative duction of section, rod, and round and shaped
movement or relative speeds tubes is located in a tool holder. This is a cassette
● Changes in the extruded material associated
in Fig. 7.1. Previously, tool heads, tool slides, or
with the deformation process rotating arms were used.
● Stress duration
In contrast, in indirect extrusion, the tool set
These result in: must be located on a tool carrier stem or by a
tool holder in the tool carrier stem, as shown in
● Decrease in strength up to softening of the Fig. 7.2.
tool working surfaces and, as a result, creep
and flow processes under thermomechanical 7.2.1 Design of the Tool
loading with temperatures in or above the
Set for Direct Extrusion
tempering region of the tooling material
● Melting in the surface region of the extruded Figures 7.3 to 7.5 depict the tool set necessary
material in extreme cases, due to thermo- for direct extrusion. This consists of the tooling
mechanical stresses for the external and internal shape-forming, in-
● Adhesive wear with metallic contact be- cluding the die, the mandrel or the hollow sec-
tween the two sliding partners without lu- tion die, as well as the support tooling. In extru-
brication as an intermediate material; the me- sion, the container is pushed against the die or
tallic contact results in the transfer of the the die holder by its hydraulic drive. The entire
softer extruded material to the working sur- tool set is then clamped between the container
face of the extrusion tooling. and the pressure ring in the press front platen
● Abrasive wear of both sliding partners in with a load up to 16% of the installed press
spite of lubricated working surfaces power. Simultaneously, the container is sealed
Dummy Stem
block
Billet
Tool set
Pressure ring
Tube
Piercing system
Container
Platen
Tool holder
(cassette)
Tool set
Fig. 7.1 Assembly of the tool set in a direct tube extrusion press. Source: Ames
420 / Extrusion, Second Edition
Die carrier stem Backer ● Tube tools for the production of round and
shaped tubes as well as hollow sections, as
Die
shown in Fig. 7.4. These extrusion tools can
also be used for the working of all extrudable
metallic materials.
● Porthole and bridge dies for the production
of hollow sections and thin-wall tubes in
long lengths. A tool stack of this type is
shown in Fig. 7.5.
Section
Pressure ring
Bolster
Bolster holder
Backer
Pressure Die
ring Feeder plate
Die
holder
Stem
Tool holder
(cassette)
Platen Tool holder Container
Fig. 7.3 Assembly of the tool set for the production of solid sections with a flat die. Source: Ames
Chapter 7: Extrusion Tooling / 421
is a backer as a support tool directly behind the For direct rod and tube extrusion of aluminum
die, as shown in the top part of Fig. 7.6. as well as copper alloys, the press size and the
The total height of the die and backer is then dimensions of the tooling involved directly and
equal to the height of the die holder. The die indirectly in the shape production, as well as the
holder must be designed so that a rapid change auxiliary and support tooling, are specified in
of the die is possible at any time. DIN 24540, published in 1986 [Ame 71]. The
Tube
Pressure ring
Bolster
Bolster holder
Backer
Pressure ring Die
Die
holder
Mandrel Mandrel
Tool holder
(cassette)
Platen Tool holder Container
Fig. 7.4 Assembly of the tool set for the production of round and shaped tubes and hollow sections using tube or section dies
together with a stepped mandrel. Source: Ames
Section
Pressure ring
Bolster
Bolster holder
Die plate
Pressure ring
Mandrel plate
Die
holder
Tool holder
(cassette)
Platen Tool holder Container
Fig. 7.5 Assembly of the tool set for the production of hollow sections in aluminum alloys using a porthole die. Source: Ames
422 / Extrusion, Second Edition
.
.
Bending, mm
.
.
.
.
.
.
Fig. 7.7 Influence of the ratio tool set diameter, d, to the diameter of the pressure ring in the press front platen, D, on bending
as a function of the increasing pressure ring radius. Source: SMS-Emoco
Chapter 7: Extrusion Tooling / 423
Piercing system
Container Tool set Sealing tool holder
Die
Fig. 7.8 Assembly of the tool set in an indirect tube extrusion press. Source: Ames
Tool
Die carrier stem Recess to receive the shell
Fig. 7.9 Indirect extrusion of aluminum alloys with a loose die holder on the tool carrier stem with the functions: extrusion die,
backer, die holder, dummy block, and cleaning block. Source: Ames
7.2.2 Design of the Tool holder, and scalping block all in one. There are
Set for Indirect Extrusion always two tool sets in operation to ensure con-
tinuous production. While one is being used for
In comparison to direct extrusion, the tool set extrusion, the other, in the case of aluminum al-
of an indirect-extrusion press consists of the loy extrusion, is having the shell removed and
stem tool carrier and the die holder with the die being cleaned or, after copper alloy extrusion,
and the backer, as shown in Fig. 7.2 and 7.8 to being cleaned together with the die ready for
7.10. There are two options for locating the die reuse. Nevertheless, in some applications, the
on the head of the stem tool carrier in indirect shell in the container in aluminum extrusion is
extrusion. In one system, the die holder is simply
placed on the stem tool carrier during every ex-
trusion cycle, using a manipulator, as shown in
Fig. 7.9 and 7.10. The other system operates
with a die holder machined into the stem tool
carrier, as shown in Fig. 7.2. The loose die
holder is easy to handle and is therefore pre-
ferred. It is used for the extrusion of aluminum
alloys as well as copper alloys. This extrusion
tool has several functions and, in the working of
copper, is both the die holder and the dummy
block. In the working of aluminum alloys, the Fig. 7.10 Indirect extrusion of copper alloys with a loose
die holder and built-in extrusion die in front of
tool shown in Fig. 7.9 is the extrusion die, die the die carrier stem. Source: Wieland-Werke AG
424 / Extrusion, Second Edition
also removed in a separate operation. In this dies or their holder, as shown in Fig. 7.11 and
case, the die holder shown in Fig. 7.2 is used. 7.12.
One disadvantage of working with loose die These sealing surfaces must be subjected to a
holders is the cooling during the cleaning opera- specific load of at least 70 to 90 N/mm2 to fulfill
tion. the sealing role. The maximum is 350 N/mm2 to
When dimensioning a tool set for indirect ex- avoid plastic deformation of the sealing sur-
trusion, it must be remembered that the stem die faces. In direct extrusion, these loads are applied
carrier undertakes the same function as the sup- by the container hydraulic sealing load. The
port tooling of the direct-extrusion tool set, with loading on the sealing surfaces is at the maxi-
the exception of the backer. The bore should of mum at the start of extrusion, due to the friction
course have the optimal dimensions for the re- or shear forces acting on the container liner wall
moval of extrusions, with the maximum possible during extrusion.
cross-sectional area. At the same time, particular To ensure adequate sealing at the end of ex-
attention also must be given to the load-carrying trusion, the container hydraulic system is de-
capacity in its support role to avoid unacceptable signed to give a sealing force of a maximum of
elastic deformations in the shape-producing ar- 16% of the press power. In the sealing process,
eas of the extrusion tooling. Both the deforma- the tool stack with the die in the press must be
tion loads as well as the deformation tempera- clamped between the pressure ring in the front
tures are the determining factors in the platen of the press and the container, so that the
dimensioning and the materials selection. centerline of the tool stack coincides with the
centerline of the extrusion press.
7.2.3 Sealing of the Shape-Producing Figures 7.11 and 7.12 describe the three seal-
ing designs used today, and these are conical,
Tooling with the Container
cylindrical, and flat sealing. Originally, the seal-
In direct extrusion, the shape-producing tools ing between the container and the die stack was
of the die or hollow die or their holder must be basically designed as a conical sealing system.
sealed against the container with sufficient com- Conical sealing has proved successful over
pressive force so that extruded material cannot many years, because it not only seals well but
be forced out between the container and the tool- also provides alignment of the die with the press
ing during extrusion. Sealing surfaces are there- and container centerlines. Conical seals are also
fore machined onto both the container and the used for the extrusion of materials with high
Die holder
Container
Pressure ring
Backer
Fig. 7.11 Schematic arrangement of the three methods of sealing the container against the die. Source: Sauer
Chapter 7: Extrusion Tooling / 425
working temperatures, for example, copper, tween the extrusion die and the container should
iron, and nickel alloys. DIN 24540 part 1 gives only be used in exceptional cases. A conical en-
a conical angle of 10⬚ and a conical length of try on the die holder and on the die (Fig. 7.14)
30 mm. can prevent shell defects, particularly with large
At the same time, conical sealing has a clear rod and tube dimensions in difficult-to-extrude
disadvantage. Under the effect of the sealing copper alloys and lubricated containers. In this
load, A, the force component, R, develops in the case, there is the risk with flat die holders and
cone and radially stresses the container in the flat dies of the shell flowing in over the dead
conical area (Fig. 7.13). The reaction force also metal zone.
stresses the die tooling. From Fig. 7.13, the ra- Under the action of the radial force, R, the
dial force is not only dependent on the sealing container opens up elastically in the sealing area,
load A but also on the cosine of the cone angle, but in contrast, the shape-producing aperture of
␣. From this dependence, the radial force de- a die is elastically compressed. This can distort
creases with increasing cone angle, ␣. For this the material flow in the shape-producing tool
reason, for years the press manufacturers have area. This has a negative effect on the accuracy
increased the cone angle of ␣ ⳱ 10⬚, according of the shape and the dimensions of the extruded
to DIN 24540, to ␣ ⳱ 35⬚ to reduce the radial product, in particular on filigree cross sections
force, after trials with an angle of 45⬚ resulted in the easy-to-extrude aluminum alloys. It does
in a negative effect on the alignment of the tool happen that the cross-sectional dimensions of
set with the press centerline. Cone angles of 40⬚ the extruded section vary from extrusion to ex-
are common in copper alloy extrusion plants. trusion due to variations in the friction condi-
Figure 7.14 describes conical seals for the ex- tions in the sealing conical faces. The majority
trusion of copper alloys. If the circumscribing of aluminum extrusion plants have therefore
circle of the cross section of the extruded prod- moved from the conical seal to the flat and cy-
uct is small, then a seal between the die holder lindrical sealing in which there are no radial
and the container, according to Fig. 7.14(a), is forces from the sealing force A. Figures 7.11 and
preferred. With larger-diameter circumscribing 7.12 as well as 7.15 and 7.16 describe these seal-
circles, sealing must be between the extrusion ing designs.
die and the container, as shown in Fig. 7.14(b). The extrusion of round and shaped tubes over
With high sealing loads, there is the risk of die an extrusion mandrel requires accurate align-
deformation. For this reason, the sealing be- ment of the extrusion die to the centerline of the
Die holder
Container
Liner
Liner holder
Mantle
Pressure ring
Backer
Die carrier
Tool sealing to container shown for die Die
diameter greater than container diameter
Fig. 7.12 Schematic arrangement of the three methods of sealing the container against the die holder. Source: Sauer
426 / Extrusion, Second Edition
Sealing force on
stripping the
taper
A = Sealing force
Press centerline
Sealing force
on sealing the
taper
Sealing/stripping:
Positive sign: sealing; negative sign: stripping
for results in automatic locking
Fig. 7.13 Forces in the conical surface of the container under the effect of the container sealing force. Source: Sauer
1 2 1 2 1 2
3 4 3 4 3 4
Fig. 7.14 Taper sealing faces for sealing between the die set and the container. (a) Taper seal between the die holder and the
container, to DIN 24540. (b) Taper seal between the die and the container, to DIN 24540. (c) Additional internal taper
on the die holder and the die, not included in DIN 24540. Source: Wieland-Werke AG
Chapter 7: Extrusion Tooling / 427
container and the extrusion press. This cannot surface as well as the conical sealing surface by
be accomplished with a flat seal, as shown in 8 to 10 mm on the container face facing the tool
Fig. 7.15, and is only possible with a cylindrical set, to allow for regrinding, as seen in Fig. 7.15
seal, as shown in Fig. 7.16. The protruding cyl- and 7.16.
inder on the die centers this in the container,
similar to the conical seal. However, with this
design, there are no undesired radial forces from
the sealing load that could influence the shape-
forming area of the die.
7.3 Extrusion Tooling for
With all sealing designs, partial plastic defor- Direct External and
mation of the sealing faces cannot be avoided Internal Shape Production
during production after many extrusions, and re-
machining may be required to ensure perfect As shown in Fig. 7.3, 7.4, 7.17, and 7.18, the
sealing. It is a good idea to extend the flat sealing extrusion die is used for direct external shape
formation in extrusion. The direct formation of
the internal shape is produced by a mandrel, as
Die holder depicted in Fig. 7.4, 7.19, and 7.20. Extrusion
Backer Die Container dies and extrusion mandrels are practically the
standard tools for extrusions. They can be used
for the working of all extrudable materials. In
addition to these standard tools, there are special
tools, including porthole and bridge dies, as
shown in Fig. 7.21 to 7.23. These combine the
direct external and internal shape formation into
a single tool.
Extrusion dies can be divided into flat entry
and conical entry. Extrusion dies with flat entries
are used for extrusion with or without a shell
Fig. 7.15 Flat seal between the container and a flat die. and without lubrication. Extrusion dies with
Source: Ames
conical entries (Fig. 7.17) or angled entries (Fig.
7.24) are used for lubricated extrusion. The die
Die holder
can also have one or more shape-forming cavi-
ties. Figure 7.18 shows a three-cavity extrusion
Die
die and a flat material entry for the production
Container
of hinges in an aluminum alloy. Extrusion dies
for the production of solid sections can have up
to eight shape-forming cavities and even more
in special cases.
The full container bore cannot be used to de-
termine the cross-sectional geometry of the ex-
truded section, defined by the circumscribing
circle of the cross section. The circumscribing
circle of the sections usually must be restricted
to 80% of the container internal diameter to
avoid the inflow of unclean billet peripheral re-
Mandrel gions into the deformation zone. However, this
value can be increased to 90% of the internal
container diameter, for example, with aluminum
billets cast in a magnetic field and turned.
When the section leaves the shape-forming
aperture, it has its final shape. To ensure trouble-
free exit, the extrusion die is opened up after the
shape-producing aperture, as shown in Fig. 7.17.
Fig. 7.16 Cylindrical seal with the container for aluminum The subsequent support tools increase in size
tube extrusion. Source: Ames from one to another in the direction of extrusion
428 / Extrusion, Second Edition
Die exit
Prechamber die
to avoid touching of the extrusion and some- mation temperature. This can result in
times plugging of the support tooling. deformation of the die close to the shape-pro-
The shape-producing apertures in the extru- ducing apertures after only a few extrusions, for
sion die are more or less subjected to high ther- example, in the case of copper alloy extrusion.
momechanical stresses, depending on the defor- This risk is countered by the use of shrunk-in
die inserts in higher hot strength hot working
steels, including austenitic steels as well as co-
balt and nickel alloys.
Only a few extruded materials can be used
with porthole and bridge dies to produce tubes
Moving mandrel
Extruded
section
Main mandrel
Die
Mandrel
During extrusion, the extrusion mandrel (Fig. threaded exchangeable mandrel tip not only al-
7.19) can, with its hydraulically controlled lows a rapid change when subjected to high ther-
speed, move faster than the extrusion stem over momechanical stresses, for example, in copper
an adjustable stroke (relative movement). This alloy extrusion, but because it sits in the main
movement can also be at the stem speed. The wear region, it can also be made from a hot
extruded material slides in the deformation zone working material with a better hot strength.
region and leaves the die with a relative speed Figures 7.19, 7.20, and 7.25 show the most
to the mandrel, so that in the shape-producing important types of mandrel. Using the hydraulic
region of the die new mandrel surfaces are being piercer on a tube press, solid billets can be
continuously thermomechanically stressed, in pierced with all mandrel types. The mandrel is
contrast to a fixed mandrel. This improves the subjected to buckling during the piercing pro-
service life of the mandrel. In addition, the for- cess and must be dimensioned accordingly.
ward movement reduces the tensile forces re- The mandrel is connected by a mandrel holder
sulting from the friction between the extruded to the mandrel bar, as seen in Fig. 7.25. This
material and the mandrel surface. To ease the then connects it with the hydraulic piercing sys-
flow process and also to provide trouble-free tem of the press. In addition, the dummy block
withdrawal of the mandrel from the extruded has a hole through it for the mandrel to move
tube or hollow section at the end of the extrusion through. The conical part of the mandrel is fre-
process, the mandrel is slightly tapered. The use quently stepped down from the remainder of the
of conical mandrels results in a conicity of the shaft, that is, slightly smaller in diameter, as seen
bore of the tubes or hollow sections. The use of in Fig. 7.19. This ensures that the shape-produc-
stepped-fixed mandrels (Fig. 7.20, 7.25) over- ing outer surface of the mandrel cannot be dam-
comes this problem. Cylindrical mandrels also aged in the bore of the dummy block.
eliminate this problem, but their use is generally The mandrel is the most highly thermome-
limited to short aluminum and copper alloy bil- chanically stressed of all the extrusion tools be-
lets. cause of the deformation temperature of the ex-
The mandrel tip can be turned onto the man- truded material. The mandrel is completely
drel shaft but also may be designed to be re- surrounded by the extruded material during the
placeable, as seen in Fig. 7.20 and 7.25. A deformation process, so that the temperature of
Fig. 7.25 Schematic arrangement of the most common types of mandrels for forming the internal profile of tubes and hollow
sections. Source: Sauer
Chapter 7: Extrusion Tooling / 431
the extruded material is entirely directed to the apertures. In general, up to 12 cavities are pos-
mandrel surface. Heat can only be extracted in- sible for the production of small and stable hol-
ternally through the mandrel cross section dur- low sections in the alloy AlMgSi0.5. In special
ing the extrusion process. Only after completion cases, even more cavities can be included, as
of the deformation of the extruded material in seen in the die in Fig. 7.27, used for the produc-
the extrusion cycle can heat be removed from tion of window spacer sections.
the mandrel surface. With high deformation The thermal and mechanical stresses in a port-
temperatures, this can sometimes result in high hole or bridge die depend mainly on the defor-
temperature fluctuations in the mandrel surface mation temperatures and the extrusion loads.
region, so that the material resistance to sudden Tensile, compressive, and bending stresses fluc-
temperature changes is exceeded. This can result tuate during the extrusion cycle. The mandrel
in a fine network of cracks in the area of the support in particular is subjected to fluctuating
mandrel surface. In the limiting case, there is the tensile and bending stresses. These stresses are
risk of the mandrel necking and failing during superimposed on the local thermal stresses re-
extrusion under the tensile load even in the ex- sulting from, for example, local heat buildup due
trusion of aluminum alloys. Therefore, highly to inadequate heat extraction with large extru-
thermomechanically stressed mandrels are inter- sion dies and stress concentrations resulting
nally cooled. The cooling fluid flows through a from notch effects. The thermomechanical
ceramic tube with holes in the mantle surface up stressing of these tools is accordingly very com-
to the mandrel tip and then returns back around plex. Heat buildup can result in plastic defor-
the ceramic tube. This internal mandrel cooling mation in the shape-forming areas of large hot
is shown schematically in Fig. 7.25. Mandrels working steel porthole dies, and stress concen-
used for deformation temperatures up to 600 ⬚C trations can result in cracks in fracture-sensitive
are not usually cooled internally. areas, for example, at the roots of the mandrel.
Porthole dies and bridge dies (Fig. 7.5, 7.21, The die designer therefore attempts to make
and 7.22) are mainly used to produce thin- these areas that are at risk from fracture inter-
walled tubes and hollow sections from materials,
changeable. In addition, he also must ensure the
the deformation conditions of which can be ther-
optimal support for the die in the tool set. In-
momechanically tolerated by the extrusion tool
sufficient heat extraction in large porthole dies
and their hot working material. The billet ma-
terial divides into several metal streams under
the influence of the extrusion load on the billet
side of the die, according to the number of feeds, B
and then recombines in the shape-forming re-
gion of the die. The material being extruded
must have adequate welding properties at the
working temperature. These are mainly tin, lead,
magnesium, and aluminum alloys. To a limited A A
extent, copper alloys can be extruded to thin-
wall tubes and hollow sections by using hot
working materials for the die material. Figure
7.24 shows such a bridge die in an old design
for the production of thin-wall brass and special B
brass tubes.
Porthole and bridge dies usually consist of
two pieces: an upper part and a lower part, as
seen in Fig. 7.21. The die upper part with the
mandrel forms the internal shape of the extruded
section, and the lower part the external shape.
The upper part also contains the material feeds
on the side facing the billet. These are usually
arranged so that the material streams follow the
shortest route through to the shape-forming re-
gion. Section A-A Section B-B
The hollow dies described can also be multi- Fig. 7.26 Bridge die for the extrusion of a tube in special
cavity; that is, they have several shape-forming brass with interchangeable nickel alloy die
432 / Extrusion, Second Edition
Fig. 7.27 Fourteen-cavity porthole die for the production of double-glazing spacers in the alloy AlMgSi0.5. Left, die plate with
the fourteen-die apertures. Right, mandrel from the billet side. Source: Erbslöh Aluminium
also reduces the extrusion speed in aluminum The wide range of production-related small
alloy extrusion. differences in the geometric design of the shape-
forming tool areas can result in unstable material
7.3.1 Control of Material flow conditions. Inaccuracies in the production
Flow in the Shape-Forming or correction of a die aperture and, in particular,
the elastic deformations from the effect of the
Region of Extrusion Tooling
extrusion load can have a more or less severe
Asymmetrical extruded profile cross sections influence on the flow resistance [Ake 85].This
with nonuniform wall thicknesses and localized explains the importance for a uniform flow of
areas of thicker material require a mechanism having, on one hand, an accurate flat parallel
for controlling the material flow in the shape- realization of the bearing surfaces in the die ap-
forming areas of the extrusion tooling. There is erture and, on the other, the prevention of un-
also the tendency for the material on the center- acceptable elastic deformation of these tool ar-
line of the die to flow faster. The aim is to control eas. Nevertheless, with an estimated bending of
the material flow so that the extruded material the die under the effect of the extrusion load, the
flows out of the die with the same speed as far bearing surfaces of the die aperture can be given
as possible over the full cross section. a slight angle in the extrusion direction so that
Figure 7.17 shows that with all types of die, this is reduced in size by the same magnitude
the shape-forming aperture has a die bearing sur- that it opens under the bending. The bending-
face in the direction of the material flow. Ad-
justing the bearing length to the cross section of
the extruded profile and the location of the die
cavity in the die produces die working surfaces
Ex
that retard the extruded material to differing de- tru
de
dp
grees by friction and shear stresses. This in- rod
uc
volves friction- and shear-related flow resis- t
tu re
tances, which are used to influence the material era
flow through the die. Figure 7.28 illustrates this e ap
Di
with a die for the production of an aluminum s Ex
ing tru
ar sio
alloy section. e nd
eb ire
Higher flow resistance values also occur in die Di cti
on
cavities that are tapered in the extrusion direc-
tion, with the normally parallel bearings being Extrusion die
related inclination of the bearing surfaces is then tooling that take into account the flow behavior.
approximately compensated. Figure 7.30 describes extrusion dies for the pro-
In addition, poor heat extraction from the duction of round bars with material-specific die
shape-forming areas of the extrusion tooling can aperture designs [Lau 76]. The entry geometry to
result in the temperature exceeding the temper- the die apertures of simple extrusion dies shown
ing temperature of the tool material used, and in Fig. 7.30 also show the variations in the radii
plastic deformation occurring after a few extru- of the leading edges and the conical entries. The
sions. use of larger inlet radii as well as differences in
The control of the material flow with the aid the lengths of the material flow paths by, for ex-
of varying flow resistances from longer or shorter ample, angled entry surfaces, as shown on a die
bearing or shear surfaces in the shape-forming for the production of steel sections by glass-lu-
tool areas cannot be used for all extrusion pro- bricated extrusion in Fig. 7.24, can result in a
cesses. It is restricted to extrusion without lubri- retarding effect at the entry of the material flow
cation. The friction in the shape-forming areas of within the geometry of the extruded section.
the tooling in glass-lubricated extrusion, for ex- The desire for the extruded material to flow
ample, of steel, and in lubricated extrusion, for faster along the centerline of the container nat-
example, of copper alloys, has little influence. In- urally influences the location of the cavities in
stead, the lubricant or the effective medium used multicavity extrusion dies. For this reason, the
as an intermediate layer separates the material be- cavities must be located as far as possible from
ing extruded from the working surfaces of the the centerpoint of the die, taking into account
tooling in the shape-forming areas, so that mixed the container internal diameter. Areas of the pro-
or even liquid friction occurs. Consequently, in file cross section where the section is thicker
these extrusion processes, an effective control of should, in principle, be located on the outside.
the material flow is far more difficult. In addition, From experience, the cavities are usually ar-
there are differences in the specific slip behavior ranged symmetrically on a circle that passes
of the extruded materials at deformation tem- through the center of gravity of the relevant pro-
perature. Materials with good slip properties are, file cross section. The axis of symmetry that
for example, lead and tin alloys. Over time, these passes through the center of gravity of the profile
properties of the materials being extruded have cross section should meet at the die center (Fig.
resulted in the development of material-specific 7.31). It must also be possible to remove the
tool designs for the shape-producing areas of the sections without any problems after they have
Extrusion Extrusion
direction direction
Fig. 7.29 Methods of controlling material flow using the friction between the extruded material and/or shearing. (a) Reduction
of the bearing length to reduce the flow resistance. (b) Tapered feed to the die aperture to increase the flow resistance
by reducing the material flow cross section and increasing the bearing length. Source: Sauer
434 / Extrusion, Second Edition
Fig. 7.30 General extruded material-specific design of the shape-forming aperture and entry form of extrusion dies. The designs
apply to (a) pure and low-alloyed aluminum alloys, (b) higher-alloyed aluminum alloys, (c) magnesium alloys, (d) lead
alloys, (e) copper-zinc alloys, (f) copper and low-alloyed copper alloys, (g) zinc alloys, (h) iron alloys, (i) titanium alloys, and (k) heat-
resistant alloys, including nickel alloys. Dimensions in mm [Lau 76]
Follower
Fig. 7.33 Principle of the follower for the classic extrusion of asymmetrical hollow profile cross section over a mandrel. Left,
terminal section in CuZn39; right, hollow section in AlZn 4.5Mg1 for military bridges. Source: Sauer
436 / Extrusion, Second Edition
and copper alloys. The material flow control in careful control of the material flow over the pro-
the production of sections occurs in the die ap- file cross section is an important requirement in
ertures by the use of different bearing lengths, the production of aluminum sections to the fin-
as described in section 7.3.1. ished dimensions to maintain the permitted
Tin Alloys. Similar to lead, tin is a metal with shape and dimensional tolerances.
good slip properties and is therefore also a base Aluminum has a high affinity for iron and thus
metal for bearing materials. Tin alloys are ex- also for hot working tool steels. The associated
truded without lubrication, similar to lead alloys. adhesive tendency to hot working steels results
Lubrication of the nitrided die aperture is not in the formation of an intermediate layer of the
used. As with lead extrusion, statistically se- extruded material several micrometers thick on
lected billets are given a very controlled brush the bearings of the die aperture after a certain
stroke of lubrication on the surface before load- number of extrusions. The deformation tem-
ing into the container. Dry friction occurs be- perature, the deformation forces, and the extru-
tween the working surfaces and the extruded sion speed also have an influence on the layer
material. There is no layer formation on the die formation [The 93, Ake 83]. The formation of
bearing surfaces as a consequence of adhesion. this layer commences at the exit edge of the die
Material flow control in the die aperture region and then develops back against the extrusion di-
can be achieved by using different bearing rection. The extruded material now slides more
lengths. over the intermediate layer and no longer on the
die bearing surface. The flow resistance in the
7.3.1.2 Control of Material shape-forming areas of the die changes as the
Flow in the Shape-Producing intermediate layer is formed. Sliding friction oc-
Regions in the Extrusion of curs between the extruded material and the die
Materials with Working bearing before the layer is formed, and shearing
occurs after the formation of the intermediate
Temperatures from 300 to 600 ⬚C
layer. This leads to permanent shear forces be-
Magnesium Alloys. Magnesium-base alloys tween the flowing extruded material and the in-
form intermediate layers of the extruded mate- termediate layer during the extrusion, as is also
rial on the nitrided bearing surfaces in the shape- the case at the liner wall in aluminum alloy ex-
forming region of the tool under the effect of the trusion.
adhesion forces, the deformation temperature, Nitriding can reduce the adhesion of the ex-
the specific extrusion load, and the extrusion truded material to the die bearings, but it is not
speed. After a certain number of extrusions, the eliminated. However, nitriding does hinder the
extruded material slides to an increasing extent layer formation; a compact intermediate layer
over the intermediate layers that form by over- forms slowly on the die working surfaces. Better
coming the permanent shear processes. The results are currently obtained with dies with
equalization of the material flow necessary for chemical vapor deposition (CVD)-coated die ap-
the production of sections is obtained in the ertures. The formation of a layer of pure alu-
same way as with aluminum alloys: by different minum and low-alloy aluminum alloys such as
lengths of the working and shear surfaces in the AlMgSi0.5 on the bearings can be retarded more
shape-producing tool area. Practically the same effectively with a 5 to 7 lm thick titanium car-
rules apply as with aluminum extruded alloys. bide or titanium nitride layer than with nitriding,
Aluminum Alloys. The hot extrusion of alu- but the formation cannot be totally prevented.
minum alloys is by far the most important ap- The vapor-deposited CVD layers are extremely
plication of extrusion. Therefore, there has been resistant to wear and achieve a very high die life.
considerable research into the flow in the shape- The closed intermediate layer that forms
forming regions of aluminum extrusion tooling against the material flow after a certain number
[The 93, Ake 85, Lan 84, Ake 83, Lan 81]. of extrusions and which subsequently increases
Aluminum-base alloys are extruded without to 4 to 6 lm or more thick determines the surface
lubrication; that is, the shape-forming region of roughness of the extruded section. The homo-
the die and the container are not lubricated. An geneous formation of the thin intermediate layer
effective control of the material flow in the tool- is consequently a determining factor for the sur-
ing shape-forming areas can be achieved rela- face roughness of the extruded product, al-
tively easily by changing the flow resistance by though investigations have revealed a higher
increasing or shortening the bearing lengths. The surface roughness of the intermediate layer com-
Chapter 7: Extrusion Tooling / 437
pared to the surface of the section [The 93]. Fi- in more detail in Fig. 7.35 and 7.36.
nally, thinner layers are always more stable than With extrusion tooling for the production of
thicker layers because of the better support from hollow sections, the material flow can be influ-
the layer carrier. This also results with increasing enced by the geometry of the material entry
thickness in unstable conditions in the interme- ports to increase or decrease the flow resistance.
diate layer adhering to the die bearings. The The bearing or shear area lengths in the shape-
shear forces between the intermediate layer and forming regions of the die depend on:
the flowing material can then partly tear pieces
● The location of the section in the die relative
from the intermediate layer, which attach them-
selves to the surface of the section. If the shear to the center of the container
● Cross-sectional variations in the section ge-
forces in the adhesive zone of the intermediate
layer with the die bearing exceed the effective ometry
adhesive forces, entire pieces of the intermediate The bearing lengths of the section depend on
layer can break away. its location relative to the container center and
In addition, according to experience in alu- must take into account that the billet material
minum extrusion plants, after a large number of flows more quickly in the center of the container
extrusions, a rather deep score forms from wear than close to the periphery of the container bore.
in the die bearing at a distance approximately Consequently, to ensure a straight extrusion with
one-third of the bearing length from the material the correct cross-sectional geometry from the die
entry side. If this reaches a specific value, the aperture, the bearing lengths at the container pe-
scoring of the section surface increases. Extru- riphery must be shorter and correspondingly
sion plants prevent this by limiting the number longer toward the die center. This is shown by
of extrusions after nitriding the dies. The rele- the bearing lengths of the section in Fig. 7.37
vant limiting number of extrusions is known and 7.38, together with their location relative to
from trials; that is, the dies are consequentially the center of the container. They show typical
used after surface treating by nitriding only up values used in practice for round and flat con-
to the point where there is definitely no severe tainers.
wear of the die bearings. For example, this can The bearing length differences needed to con-
be up to 70 extrusions for porthole dies for trol the material flow of an extrusion die moving
working easily extruded alloys and even more out radially from the container center depend on
for dies for solid sections. The number of extru- the following rules:
sions can be increased after the second nitriding,
● For round containers, the bearing lengths
because the bearing wear resistance is increased
by the additional nitriding. The die can also give must be reduced by 1 mm for each 25 mm
a higher throughput after the second and third moved from the container center (Fig. 7.37).
nitriding.
The minimum length of the die bearing sur-
faces for hot working aluminum alloys depends
on the alloy. If the bearing lengths reach the min-
imum length as a result of correction to balance
the material flow, then further correction is no
longer possible. In this case, an angled shape to
the die aperture with otherwise parallel bearings
in the areas that are still flowing too quickly can
give an effective flow restriction (Fig. 7.24).
In addition, the material flow in the shape-
forming aperture of a die can be influenced by
the geometric location of a milled shaped feeder
chamber in front of the die cavity. Figure 7.34
shows an example of a feeder chamber. The en-
try edges of the shape-forming die aperture in
the heavy regions of the profile cross section
must be in the zone of influence of the dead
metal zone that forms at the external periphery Fig. 7.34 Feeder chamber to control material flow. Source:
of the feeder chamber, as seen in Fig. 7.34 and Ames
438 / Extrusion, Second Edition
(a) (b)
Fig. 7.35 Feeder chamber geometry for material flow control. (a) Shows correct feeder chamber size for material flow control
(b) Has no effect on the material flow. Distance s ⱕ t provides correct feeder chamber geometry for material flow
control. Source: Ames
● For containers with an oval cross section, the Fig. 7.38 and the section circumscribing di-
die bearings must also be reduced by 1 mm ameter.
according to the radial distances given in For material flow control with cross-sectional
Chapter 7: Extrusion Tooling / 439
U R
file pe riphery) (mm) (mm)
420 (Pro
Diameter
4 5 6 6 5 4 Over To
350 65
4 6 6 4 350 400 75
. 400 450 85
R
450 500 95
4 6 6 4
0
+6
R
20
+1
R
Fig. 7.38 Bearing lengths needed in the die aperture to achieve a uniform flow across the profile cross section according to the
location of the section relative to the center line of an oval container. Source: Ames
Fig. 7.39.
● With wall thickness differences greater than
5 to 1, the material flow must be further re-
duced with the feeder chamber (Fig. 7.34) or
3 slowed at selected feeds on hollow dies.
12
12
15
Table 7.1 Minimum bearing lengths for easy-to-extrude aluminum alloys as a function of the wall
thickness and circumscribing circle of the cross section of the semifinished product
Minimum bearing length, mm
Diameter of the circumscribing circle, mm
Wall thickness, mm 30 60 100 150 200 250 300 400 500
To 1.5 2 3 3.8 3.8 4.5 4.5 ... ... ...
2 3 3 3.8 4.5 4.5 5 5 ... ...
3 3 3.8 4.5 4.5 5 6 6 6.8 ...
4 4.5 4.5 4.5 5 6 6 7.5 9 9
5 4.5 6 6 6 7.5 7.5 9 9 10.5
6 6 7.5 7.5 7.5 9 9 10.5 10.5 12
8 7.5 7.5 7.5 9 9 10.5 10.5 12 12
10 9 9 9 10.5 10.5 10.5 12 12 12
13 9 10.5 10.5 12 12 12 12 12 13.5
16 10.5 10.5 12 12 12 13.5 13.5 13.5 15
Over 16 10.5 12 12 13.5 13.5 13.5 15 15 18
Source: Ames
440 / Extrusion, Second Edition
ters in easy-to-extrude aluminum alloys. Table Taken altogether, the guidelines mentioned
7.1 gives an overview of the minimum bearing enable, for example, the production of an extru-
lengths for the easy-to-extrude aluminum alloys. sion die with a bearing geometry of the shape-
Dies for moderately difficult and difficult-to- producing aperture suitable for the manufacture
work alloys require longer minimum lengths. of extruded sections with the cross section
For the moderately difficult-to-extrude alumi- shown in Fig. 7.39.
num alloys, the minimum lengths given in Table After leaving the die bearing in the shape-pro-
7.1 must be increased by 15% and by 30% for ducing region, the section is fully formed. To
the difficult-to-extrude alloys. These extruded enable it to emerge from the die without any
alloys are listed in Table 7.2. contact problems, the bearing surface is relieved
Section surface areas with grooves or protru- by 0.5 to 3 mm, depending on the bearing length
sions (Fig. 7.40) require a 30 to 50% reduction (Fig. 7.17), and the die exit is relieved by an
of the bearing lengths given in Table 7.1. angle of 1 to 5⬚. There are also section areas, for
The bearing lengths in the shape-forming re- example, legs, where the exits from the bearings
gions of round bar and round tube dies are a must be relieved cylindrically for reasons of die
function of the bar or tube diameter. The extrud- stability, as seen in an enlarged section in Fig.
ability of the relevant aluminum alloy must be 7.39. The relief of the die bearings is selected so
taken into account. Figure 7.41 gives more in- that deformation of the bearing by the forces de-
formation. veloped during extrusion cannot occur.
The bearings of a mandrel in a hollow section
die are mirror images of the bearings of the die
aperture. For example, the bearings in the die
Table 7.2 Bearing length addition as a plate of a porthole die to produce thin-wall tubes
function of the extrudability of specific have an annular shape, and the bearings on the
aluminum alloys mandrel with which the die forms the shape-
Alloys forming region also have an annular profile. Be-
Extrudability Easy Moderate Difficult cause of possible deflection of the mandrel by
Addition, % None 15 30 transverse forces, for example, from wall thick-
Material 1350 5049 2014A
6060 5051A 2017A ness variations in the profile cross section, the
6082 5251 2024 bearings at the entry to the shape-forming region
7020 5083 are extended by 1.0 to 2.5 mm to prevent defec-
7022
7075 tive material flow.
Source: Ames
Bearing length, mm
Bar/tube diameter, mm
7.3.1.3 Control of Material Extrusion dies and inserts for the production
Flow in the Shape-Producing of brass bar and wire usually have bearing
Regions in the Extrusion of lengths of 5 to 10 mm in the die aperture and an
Materials with Working entry radius of 0.5 to 1 mm. Extrusion dies for
Temperatures from 600 to 1300 ⬚C copper-zinc alloy sections normally have bear-
ing lengths of 5 to 15 mm and, in individual
Copper Alloys. Up to the shape-forming cases, even 25 mm. However, there is no fixed
tooling, the extrusion of copper alloys is carried rule for the final bearing length dimensions in a
out without lubrication and with a shell. In con- die. Designers and die manufacturers must co-
trast, the shape-forming area is carefully lubri- operate to find the optimal solution based on ex-
cated to avoid layers of the extruded material perience. The different bearing lengths are pro-
forming on the die bearings at the high defor- duced either by back milling the previously
mation temperature. Copper and copper alloys eroded die aperture or by eroding the die exit
with a zinc content up to 20% become coated before wire eroding the die aperture. The exit
with copper oxide during heating to the extru- from the die is usually undercut by 1 to 3 mm
sion temperature, and this acts as a lubricant. and then tapered to avoid contact with the ex-
Occasionally, in special cases, copper alloys are truded section, similar to aluminum alloys. The
also hot extruded with a lubricant. In this pro- leading edges of the die are usually broken with
cess, the lubricant moves with metal flow into a radius of 0.3 to 0.5 mm, in other words, almost
the die area. Overall, the lubrication in the a sharp edge. In addition, the same basic rules
shape-producing tooling produces friction con- as those for aluminum sections apply to the ma-
ditions in the mixed-friction range. terial flow in the die apertures of dies for the
Different bearing lengths are also used with production of brass sections.
copper alloys for necessary flow control for pro- Titanium, Iron, and Nickel Alloys. Materi-
ducing sections, as shown in Fig. 7.42 and 7.43. als extruded at temperatures above 1000 ⬚C are
However, compared to aluminum dies, these extruded at high speeds with glass lubrication to
must be longer because of the fundamental lu-
avoid thermal overstressing of the extrusion
brication of the shape-forming area and the sig-
tooling. A disc of compacted glass granules be-
nificantly higher thermomechanical stresses.
tween the end of the billet and the die separates
The lubricant reduces the abrasive wear of the
the front of the extrusion from contact with the
bearings as far as possible and practically elim-
inates the adhesive wear. If necessary, localized die bearings at the start of extrusion. Fluid pres-
material flow variations that are not too severe sure forms in the glass film through a lubricant
in dies in production can be compensated by wedge between the extruded material and the die
controlled lubrication of the die aperture. The on the feed surfaces to the die aperture as a result
material flow of profile cross-sectional areas of the high extrusion speed. Liquid friction then
flowing too slowly can be improved by increas- occurs on the shape-producing areas of the tool-
ing the localized lubrication. If necessary, parts ing. A balanced material flow over the profile
of the cross section that are flowing too quickly cross section is therefore not possible. Never-
can be retarded by tapering the die inlet, as theless, some material flow control can be
shown in Fig. 7.29(b). Whereas extruded pro- achieved by using angled feed paths of different
files in copper or copper alloys that can be read- lengths and variations in the entry radii, as
ily cold worked can, in principle, be brought to shown in Fig. 7.24. This enables simple cross-
the specified dimensions by drawing, sections in sectional geometries without excessive wall
the high-zinc-containing ␣-b brasses must be thickness variations and large masses to be pro-
extruded close to the finished size or, as with b duced as solid sections and hollow sections over
brass, to the finished size. A balanced material a mandrel.
flow control is therefore essential for the
production of a quality product. However, in 7.3.2 Dimensions of the Die Apertures in
contrast to copper, these materials require con- Relation to the Specified Section
siderably lower working temperatures. Conse-
Dimensions at Room Temperature
quently, the die bearings are subjected to signifi-
cantly lower temperatures. This enables In hot working processes, the material has a
effective flow control to be achieved with vary- larger volume during the deformation than at
ing bearing lengths, as shown on the right side room temperature, depending on the specific
of Fig. 7.42. material and temperature. The material volume
442 / Extrusion, Second Edition
Fig. 7.42 Extrusion dies for the production of CuZn39Pb3 sections. Source: Sauer
correspondingly decreases on cooling. The ex- tion. Additional additive dimensional differ-
tent of the volume change (shrinkage) varies ences from other causes also must be taken into
with the material. This also applies to the hot account.
working material used for the die. Because most Additions to the specified dimensions of the
extruded materials in nonferrous metals have co- profile cross sections arise from the following:
efficients of expansion significantly higher than ● Specific coefficients of expansion of the ex-
the hot working materials, this means that the truded material heated to the deformation
extruded section has cross-sectional dimensions temperature
smaller than the corresponding dimensions in ● Specific coefficient of expansion of the hot
the die cooled to room temperature. The differ- working material used for the manufacture
ence is referred to as the shrinkage. This must of the tooling heated to the working tem-
be taken into account by adding a factor when perature
determining the tool dimensions in the die ap- ● Tolerance fields of the profile cross-sectional
ertures. However, these shrinkage allowances geometry
are only one of the measures that must be taken ● Tendency of the extruded material to flow
to determine the necessary dimension of the more quickly in the center of the container
shape-forming part of the die to achieve the cor- ● Tendency of the extruded material to flow
rect specified dimensions in the profile cross sec- more slowly in thin-wall areas of otherwise
Chapter 7: Extrusion Tooling / 443
Fig. 7.43 Extrusion die for the production of a furniture hinge section in brass. (a) Die and profile cross section. (b) Die aperture
bearing lengths. (c) Section through die aperture. Source: Wieland-Werke AG
massive cross sections, particularly in the The first stage is to determine the additions to
outer regions. Particularly high dimensional the specified dimensions to compensate for the
additions are needed in this case. pure thermal volume change (shrinkage). The
● Elastic deformation of the shape-producing percent material-dependent dimensional addi-
tool areas under the effect of the extrusion tions are taken from Table 7.3. This is 1.2% for
load, which cannot be completely avoided in the alloy AlMgSi0.5, corresponding to the alloy
spite of good support number 6060. The resultant die aperture dimen-
● Additions to allow for the stretching of the sions are given in Fig. 7.44(a) in parentheses.
extruded section In the second stage, the die aperture dimen-
sions given in parentheses in Fig. 7.44(a) for the
The dimensions for the die aperture are de- pure thermal volume change are placed in the
termined for the example of the aluminum sec- relevant tolerance field, taking into account the
tion in AlMgSi0.5 shown in Fig. 7.44, taking the tolerances of the specified section dimension
aforementioned parameters into account. This is and the die wear. The permitted deviations from
divided into three stages for clarification. the nominal dimensions are shown in Fig.
444 / Extrusion, Second Edition
(3.036)
Material 1350 7003 2014A 5083
(31.372)
5051A 7020 2017A 7022
31
6005A ... 2024 7075
(54.648)
6060 ... ... ...
54
6061 ... ... ...
(3.036)
6082 ... ... ...
3 6101B ... ... ...
6106 ... ... ...
(a) Source: Ames
15 +0.4 72 +0.2
–0.8 15 +0.4
0
0
(15.2) (72.56) (15.2)
3+– 0.2 3+– 0.2
(3.036) (3.036)
count the effect of the elastic deformation of the
die, in particular, the bending of the die aperture
(3.036)
– 0.2
ified dimensions.
3+
(3.276)
– 0.2
3+
– 0.2
3+
(a)
. .
.
.
.
.
.
.
(b) (c)
Fig. 7.45 Two-cavity die for the production of a brass angle section. (a) Die with profile section. (b) Specified dimensions of the
section and increased dimensions in the die aperture. (c) Die aperture bearing lengths. Source: Wieland-Werke AG
alloys requires an increase in dimensions of In the production of steel sections, the die ap-
1 to 2%. ertures are generally produced with the cross-
Moreover, the production of the same section sectional dimensions of the section being in-
in copper alloys on different extrusion presses creased by 2%, whereby the final dimensional
with different die stack arrangements or maxi- increase must be left to the experience of the
mum extrusion loads requires different die ap- designer. In comparison to dies for the extrusion
erture dimensions. The radial force R shown in of copper alloys, even stricter relationships ap-
Fig. 7.13 from the conical sealing of the tooling ply because of the particularly high thermome-
can also play a role. Naturally, whether the ap- chanical stresses in the die aperture region and
erture of the die backer is optimally matched to the rapidly occurring plastic deformation.
the cross-sectional geometry of the die aperture 7.3.3 Tooling for the
also plays a role. Identifying the correct increase
Extrusion of Materials with
in the dimensions for the die aperture of a die
for the deformation of copper alloys does require Deformation Temperatures
considerable experience and cannot be covered in the Range of 0 to 300 ⬚C
by a specific formula, although the collection of Tooling for the extrusion of tin and lead alloys
statistical data is informative. follows a similar but simpler design to alumi-
446 / Extrusion, Second Edition
Fig. 7.47 Split two-part porthole die for the production of an automobile roof section in magnesium alloy. Source: Honsel AG
Chapter 7: Extrusion Tooling / 447
Fig. 7.48 Flat die for the production of the solid AlMgSi0.5
section shown in front of the die. Source: Alu-
suisse Fig. 7.49 Flat die with integrated feeder chamber for the
production of the solid AlMgSi0.5 heat exchanger
section in front of the die. Source: Alusuisse
Fig. 7.50 Porthole die for the production of the AlMgSi0.5 flexible construction system section in front of the die. Left, upper
part with ports and mandrel; right, die plate with welding chamber and die aperture. Source: Alusuisse
448 / Extrusion, Second Edition
Fig. 7.51 Porthole die for the production of the AlMgSi0.5 hollow section shown in front of the die for a water-cooled exhaust
duct from a marine diesel engine. Left, mandrel; right, die plate. Source: Alusuisse
Fig. 7.52 Porthole die for the production of the AlMgSi0.5 section shown in Fig. 2.53 in Chapter 2 and in front of the die for
pneumatic control elements. Left, mandrel; right, die plate. Source: Alusuisse
● The extruded material flows more quickly in ● Degree of difficulty of the profile cross-sec-
the center of the container than in the pe- tional geometry
ripheral zones. ● Size of the section circumscribing circle
● Large material masses in the section flow ● Flow stress of the material
more quickly than thin-wall areas. ● Weight per meter of the section
● The deformation loads acting on the die re-
Aluminum Extrusion Dies. Figures 7.18,
sult in elastic shape changes in the die ap-
7.28, 7.31, 7.34, and 7.39, as well as 7.48, 7.49,
erture.
and 7.53 show single-cavity as well as multi-
The design- and production-related require- cavity extrusion dies, with and without a feeder
ments of aluminum extrusion die manufacture chamber, used for the production of rod, tube,
increase with: and solid sections. Feeder chambers were intro-
Chapter 7: Extrusion Tooling / 449
mechanical stresses and the customer is in agree- eter to prevent the inflow of the billet peripheral
ment. Finished products that are subjected to regions into the section. The maximum size of
higher mechanical stresses must not contain any the cross section that can be produced is thus
transverse weld. limited by the respective container and the
Feeder Chambers. The material flow in the press. In contrast, profile cross sections with a
shape-forming die aperture in aluminum extru- circumscribing diameter larger than the con-
sion is controlled by increasing or decreasing the tainer diameter can be produced by using a
flow resistance by different bearing or shear sur- spreader chamber, as shown in Fig. 7.55. This
face lengths. This can be seen in Fig. 7.28 and requires that sufficient material be fed to the
7.39. With complicated cross-sectional geome- shape-producing die aperture area through the
tries with large variations in cross section (Fig. spreader chamber during the extrusion.
7.34) and also in massive profile cross sections Spreader chambers are increasing in impor-
(Fig. 7.36), this technique of material flow con- tance. The development of spreader technology
trol may not be sufficient in some applications. is used more and more to also produce flat and
In these cases, a feeder chamber can help, as wide cross sections from round containers on
described elsewhere, because this enables an ad- small extrusion presses. In addition, the devel-
ditional braking effect to be applied to the ma- opment has shown that it is possible to produce
terial flow. large flat and wide sections from round con-
The requirements to achieve this flow restric- tainers that previously could not be produced
tion in the feeder chamber are shown in Fig. on large extrusion presses without using rectan-
7.35. As shown in Fig. 7.34 to 7.36, the feeder gular containers. To achieve strong transverse
chamber is milled into the front side of the die welds, adequate extrusion ratios as well as strict
in such a way that the periphery is close to the maintenance of the conditions described in the
entry of the die aperture area that must be section about welding chambers for billet-on-
slowed. This occurs, as depicted in Fig. 7.35(a), billet extrusion must be fulfilled. It is particu-
by dead metal zones forming in the areas of in- larly important that the front face of the follow-
fluence in the feeder chamber, which exert a ing billet is largely free of oxide. It appears
braking effect. possible that in the future, flat containers, which
Figure 7.36 shows this possibility of influ- are not particularly economic because of the
encing the material flow in a profile with a mas- low service life of the liner, will be largely re-
sive rectangular cross section. The corner re- placed by round containers with spreader cham-
gions of the rectangular section naturally have bers.
more flow resistance to overcome as a conse- Extrusion Mandrels. Difficult-to-extrude
quence of friction and shear than the two side aluminum-base alloys, including the high-mag-
faces of the profile cross section. Consequently, nesium-containing alloy group AlMg from
the extruded metal flows more quickly in the AlMg1.5 as well as the copper-containing alu-
free side areas of the cross section than in the
corners. By locating the peripheral zones of the
feeder chamber close to the die aperture at the
leading edges of the free side surfaces of the
extruded section, the dead metal zones that
form here will influence the material flow in the
same way as in Fig. 7.35(a). The material flow
is retarded. The situation in the location of the
section corners is different. Here, the peripheral
areas of the feeder chamber have a definite dis-
tance from the die aperture. Consequently, there
is no influence. Overall, this additional retard-
ing of material flow using a feeder chamber can
be used over the full periphery of the die ap-
erture, as illustrated in Fig. 7.35, or locally, as
in Fig. 7.36.
Spreader Chamber. From experience, the
circumscribing circle of a profile cross section Fig. 7.55 Production of profile cross section with a circum-
scribing circle greater than the container bore us-
should not exceed 80% of the container diam- ing a spreader chamber. Source: Ames
Chapter 7: Extrusion Tooling / 451
minum alloys, cannot be extruded with porthole stresses during the extrusion process and, con-
and bridge dies because of the high flow stress sequently, severe wear. If necessary, the ability
as well as the defective extruded weld strength. to change the mandrel tips enables them to be
Tubes and hollow sections in these alloys must manufactured from hot working materials with
be produced on tube presses, as shown in Fig. a higher strength than that needed for the man-
7.4, 7.19, and 7.20. This also applies to thick- drel shaft. In addition, in specific cases, the
wall tubes and hollow sections in the easy and mandrel tip can be increased to 200 mm to en-
moderately difficult-to-extrude aluminum alloys able a small relative movement, giving a better
AlMgSi0.5 with wall thickness greater than 40 control of the high thermomechanical stresses.
mm and AlMgSi1 with wall thickness over 30 Porthole Dies. The most striking and most
mm, because of defective extrusion weld important tool for the production of sections in
strengths. With large tubes, the maximum in- the low-to-moderately alloyed aluminum alloys
ternal tube diameter is limited by the maximum is the porthole die. Figures 7.21 and 7.22 show
possible stem bore and the related maximum schematically two typical porthole dies in two-
possible mandrel diameter. The maximum tube cavity and single-cavity designs for the produc-
external diameter is limited to 80% of the con- tion of aluminum alloy hollow sections. With
tainer liner diameter by the cylinder seal be- these dies, it is possible to produce very de-
tween the die and the container. Tapered mov- manding extruded products in aluminum alloys
ing mandrels as well as fixed mandrels with with high dimensional and shape accuracy.
stepped mandrel tips are used, as shown in Fig. Without these special tools, there would be no
7.19 and 7.20. Short billets can also be extruded large-section technology with stress-specific
to tubes, using cylindrical mandrels. In contrast profile cross-sectional geometry for demanding
to mandrels for copper production, mandrels for designs.
the production of aluminum tubes are not Porthole dies are usually two-piece (Fig.
cooled externally or internally. 7.50, 7.51). The internal shape formation takes
Moving tapered mandrels for the extrusion of place in the upper part, and the external in the
aluminum alloys are usually given a taper of lower section. The divided-material streams,
0.08 to 0.09%. The taper ensures that the man- corresponding to the number of ports formed in
drel can be withdrawn without problems after the upper part, are reunited in the welding
extrusion, in spite of the shrinkage of the alu- chambers of the die lower section immediately
minum tube as a result of cooling. The axial in front of the die aperture. This produces lon-
movement ensures that the thermal stressing of gitudinal welds that should not be located in the
the mandrel is minimized by ensuring that new decorative surface zones of the profile cross
mandrel surface areas in the die aperture con- section. The design of the welding chambers
tinuously come into contact with the extruded can be seen in Fig. 7.50 to 7.52. The longitu-
material heated to the deformation temperature. dinal welds themselves must be able to with-
In addition, billets can be pierced in the con- stand adequate mechanical stresses. Therefore,
tainer with these mandrels immediately before the material properties in the region of the lon-
extrusion, provided the piercer is powerful gitudinal weld should, in principle, be the same
enough. Moving tapered mandrels also enable as in the core region.
the maximum billet volume, which depends on Certain die-related rules must be taken into
the tube press, to be used. With a large 100 MN account to ensure defect-free longitudinal ex-
press power, this means, for example, mandrel truded welds:
lengths of 1200 mm with 1100 mm billet
lengths. ● The material inlet ports must be large
Stepped mandrels cannot be used with these enough to develop a sufficiently high defor-
billet lengths, because the shaft lengths must be mation pressure in the welding chambers.
limited due to the higher mechanical stresses. ● The material entry ports should not be too
Higher friction and shear forces between the large, so that rapid emptying of the ports by
extruded material and the axially located cylin- the material from the next billet can occur,
drical mandrel shaft produce these stresses. To- producing short transverse weld seams.
day, stepped mandrels are usually fitted with ● The material entry ports should only be lo-
replaceable tips, as shown in Fig. 7.20 and 7.25, cated in a circumscribing circle diameter up
because fixed mandrel tips in the die aperture to approximately 90% of the container di-
are subjected to the highest thermomechanical ameter. This prevents entry of material from
452 / Extrusion, Second Edition
Fig. 7.56 Welding chamber dimensions for porthole dies. Source: Ames
the periphery of the billet. If this percentage to the leading edges of the die aperture in the
is exceeded, then the billets must be ma- region of the mandrel circumference and the die
chined. aperture circumference is equal, to achieve a
● To achieve a good decorative appearance, symmetrical dead metal zone.
the extrusion welds must be located in the The cross-sectional geometry and the loca-
section corners or in areas where there are tion of the material inlet ports to the die axis
no decorative demands. on the billet-facing side of the porthole die have
● The extrusion ratio should exceed 14 to 1 an important influence on the material flow and
to obtain qualitatively good extrusion welds. consequently on the deformation characteris-
● Longitudinal welds with adequate mechan- tics. Under normal extrusion conditions, the fol-
ical properties require specific welding lowing design rules apply for this part of the
chamber dimensions. Guidelines are given die:
in Fig. 7.56.
● The material entry ports in the porthole die
The size of the factors in the equation to es- should have a simple cross-sectional ge-
timate the welding chamber size, AS, depends ometry and also have the same cross-sec-
on the extrudability of the aluminum alloy used. tional area for the same distance from the
Easily extruded alloys have a low factor, and die axis. At the same central position of the
moderately difficult ones a high factor. Defect- port from the die axis, the extruded material
free welding of the material streams of the ex- will flow more quickly in a large port than
truded material, and hence longitudinal welds in a small port.
with adequate strength, can be ensured by fol- ● As a consequence of the faster material flow
lowing this approach to estimate the size of the in the region of the die centerline compared
welding chamber. If dimensions below the to the material flow further away, the ports
guidelines are used, then this will impair the obviously must have different cross sections
quality of the longitudinal welds. Exceeding the
guidelines results in more severe bending of the
mandrel area of the die upper section as a result
of the associated increase in the height of the
welding chamber. In addition, the quality of the
longitudinal weld in single-cavity porthole dies
can also be positively influenced by the location
of the welding chamber relative to the cross-
sectional geometry of the extruded section.
The material flow can be influenced by ma-
chining in a shaped feed chamber at the bottom
of the welding chamber in front of the entry to
the porthole die aperture, similar to that used
for flat dies for aluminum, as shown in Fig.
7.57. This clearly shows that the shaped feeder Fig. 7.57 Design of a shaped feed chamber in porthole
chamber must be designed so that the distance dies. Source: Ames
Chapter 7: Extrusion Tooling / 453
to balance the different material flow rates arranged at specific distances from the die axis
(Fig. 7.58). or the container centerline. To supply the die
● The number of the material inlet ports de- apertures with the extruded material, the ports
pends on the profile cross-sectional geom- are positioned at different distances from the
etry; that is, the more complicated the ge- center of the die, as seen in Fig. 7.21. This ne-
ometry, the greater the number of ports cessitates the application of the rules described
needed to ensure a uniform material flow. for ports with different cross sections. The re-
duction in the material flow rate toward the
Figure 7.59 shows the application of these container liner wall also must be compensated
rules. by increasing the size of the ports. This is ex-
The different location of the ports relative to plained in Fig. 7.60.
the axis of the porthole die results in different Guidelines for the specific increase in size of
port areas. This sensitive reaction of the mate- the port areas as a function of the distance from
rial flow to the location and the cross-sectional the die or container axis can be obtained using
area of the ports can be used with porthole dies the relationships based on practical experience
in comparison to flat dies with feeder chambers given as follows:
for additional material flow control, which
helps in the production of complicated profile Sa ⳮ Si
cross-sectional geometries.
An economic production assumes the use of
Aa ⳱ 1 Ⳮ冤 100 mm i 冥
A (mm2)
Aa ⳱ [1 Ⳮ 0.5]Ai ⳱ 1.5Ai(mm2)
A=
600
mm 2
A=
750
R2
mm 2
5
R36
A= R34
73
0m
R2
m2
5
A=
60
0m
m2
Low speed
Moderate speed
High speed
1 2 3 4 5
Fig. 7.62 Influence of the mandrel cross section on the section exit speed. Source: Ames
Chapter 7: Extrusion Tooling / 455
of the previously extruded bar out of the bridge by machine. After the heat treatment of the
die without welding to it. blank, the die aperture was spark eroded to the
The die design must take into account the finished size. With the introduction of CAD/
stripping process. It can be seen in Fig. 7.23 CAM, the clearance can be finish spark eroded
that this type of die has die feeds of equal size, together with the production of the bearing
and the outer limit is determined by the liner lengths in the externally finish-machined and
wall. The legs and material feeds are designed heat treated steel blank, and the die aperture cut
so that they can be cleared without difficulty by out using a computer numerical controlled
pulling the material out. For this reason, the (CNC) wire erosion machine. Figure 7.63 gives
feeds open out toward the end facing the billet, an overview of the operations involved in the
and the bridge surface is conically tapered in production of a section extrusion die. The pro-
the same direction. At the same time, this die duction of a hollow die involves more milling,
design also ensures the feed of the metal drilling, and grinding operations. However, the
streams into the interior of the die without any die undergoes the same operational steps as de-
problems and with the exclusion of atmospheric scribed in Fig. 7.63. The total production route
oxygen, as with porthole dies, where they weld for the manufacture of a two-piece porthole die
together. High-quality longitudinal welds are is described in Fig. 7.64.
produced. This requires that only clean areas of The CNC program is sent directly to the pro-
the billet peripheral zone flow into the die; that duction machine from the CAD/CAM system.
is, the billets must be skimmed. The design en- The storage of repetitive design operations is
sures that bridge dies transfer their heat more also a major advantage of a CAD/CAM system.
easily than the closed porthole die. As a result, For example, the following can be stored:
higher extrusion speeds are possible.
● Tool assembly in the extrusion press
In addition to these advantages, bridge dies
● Tool set makeup
also have some disadvantages:
● Machine-dependent tool dimensions accord-
● Because billet-on-billet extrusion is not pos- ing to DIN 24540, including drill holes,
sible, the front end of every extrusion must keyways, and identification slots
be guided through the support tooling and ● Dimensions of support tools
the platen, producing a higher scrap rate. ● Die holder design dimensions
● Water quenching of the extruded section ● Pitch circle of the die cavities for a multi-
with a standing wave is only possible to a cavity die
limited extent. ● Feeder chamber designs
● The maximum billet length is limited by the
height of the bridge extending into the con- For example, drawing elements and parts list
tainer. can also be stored, readily called up, and in-
● The thicker. discard needed for the stripping
cluded in the new design drawing. These aids
have considerably reduced the design work by
process reduces the useful length of the
the die manufacturer as well as the possibility
billet.
of manual errors. Naturally, the actual design is
still dependent on the knowledge of the die de-
7.3.4.3 Manufacture and Operation of
signer and the way he uses the possibilities of-
Aluminum Extrusion Tooling fered by CAD/CAM.
Manufacture of the Extrusion Tooling. The In addition, the application of CAD/CAM
introduction of efficient computer-aided design/ systems together with the use of CNC machines
computer-aided manufacturing (CAD/CAM) by the die manufacturer enable a previously un-
systems, combined with the application of nu- attainable and reproducible accuracy to be
merically controlled machines, resulted in a achieved. This has resulted in a reduction in die
permanent change in the design and manufac- trials before the first production run of a die
ture of extrusion tooling [Kle 86]. The empha- and, in particular, a high repeatability of the
sis in aluminum tooling manufacture moved second and third die, which exactly match the
from the machining to the design. Previously, original. In many cases, die trials are not
for example, the die aperture and exit of a sim- needed for the second and third die.
ple die were marked out on an externally finish- Aluminum extrusion tooling undergoes high
machined tool steel blank, the exit clearance mechanical and moderate thermal stresses. At
was milled out, and the die aperture sawn out the stem head, specific pressures up to 1100 N/
456 / Extrusion, Second Edition
Fig. 7.63 Schematic production plan for the manufacture of a section extrusion die for the production of a flat aluminum alloy
section. Source: Sauer
Chapter 7: Extrusion Tooling / 457
Preparation of the machining programs for the die and the sink
electrodes using CAM
Blank rough machining (turning) to Cutting by wire erosion Blank rough machining (turning and milling)
exact external dimensions on CNC machines on CNC milling machine
Heat treatment
Milling of the feed parts
and the mandrel on CNC milling
machines Production of the die exit by sink
Heat treatment erosion with simultaneous cutting
of the bearing lengths of the die aperature
Inspection
Trial extrusion
Correction
Production
Fig. 7.64 Schematic production plan for the manufacture of a two-part porthole die for the production of a hollow section in a
low-alloyed aluminum alloy. Source: Sauer
458 / Extrusion, Second Edition
mm2 can occur, and hollow dies must withstand Testing is carried out by taking samples along
temperatures up to 600 ⬚C in the die apertures. the length of the extrusion and measuring and
Under these thermomechanical loads, the tool recording.
must produce an extruded geometry that is ac- The die is released for production or cor-
curate in both dimensions and shape. The axial rected, depending on the test results. Corrected
forces acting on the billet-facing surface cannot dies must be retrialled. The most common cor-
be withstood by the die alone. Optimal support rections involve:
from the support tooling must be provided as
shown in section 7.2.1. The extrusion tooling ● Die dimensions to produce the specified fin-
must be capable of withstanding the deforma- ish dimensions in the cross section of the
tion forces developed in the shape-producing semifinished product at room temperature
areas. The tool designer, the extruder, and the ● Unequal material flow across the section
customer must specify the final product cross- ● Feeder chamber geometry
sectional geometry to be tool compatible by “si- ● Port geometry with hollow dies
multaneous engineering.” Figure 7.65 describes ● Welding chamber dimensions with hollow
the path currently followed from order intake dies
to the manufacture of the extrusion tool.
The deformation temperature of aluminum Aluminum extrusion die manufacturers are
alloys is generally below the tempering tem- moving in the direction of higher die accuracy,
perature of the classic hot working tool steels. with the intention of largely eliminating the ex-
These steels are therefore used for the manu- pensive die trials.
facture of aluminum extrusion tooling. In the If the die trial results are satisfactory, the tool
die apertures of large-profile dies, operating is cleaned of aluminum in hot caustic soda, fol-
temperatures up to 600 ⬚C can develop from the lowed by wet or dry shot blasting with sand,
heat produced during the extrusion, combined glass, or steel balls. The die is finally nitrided.
with the inadequate heat extraction through the Coatings with titanium nitride or chromium car-
tool surface. In these cases, hot working tool bide are also possible but require significant in-
steels with a higher resistance to tempering vestment.
must be used for the manufacture of these dies. For production, the dies must be carefully
The classic hot working tool steels are de- and fully preheated. Support tooling should also
scribed in detail in the section “Hot Working be preheated to avoid heat loss from the die at
Materials for the Manufacture of Extrusion the start of extrusion. Special die ovens located
Tooling” in this chapter. close to the extrusion press are used for die pre-
Working with Extrusion Tooling. Die trials heating. The furnace chamber must have pre-
are carried out after the bearings have been pol- cise temperature control. When a die is re-
ished and the hollow die assembled. Today, moved or a cold die loaded into the oven, the
CAD/CAM manufactures second and third dies resultant temperature decrease must be taken
so closely to the first die that, to an increasing into account by increasing the time. Strict main-
extent, die trials are not required for these tools. tenance of the specified billet temperature is
Die trials are carried out under production also important for a long tool life.
conditions, that is: The following rules apply in tool preheating:
● Extruded material and billet dimensions ● The toughness of the tool increases with
● Billet and die temperature through heating. Complete through heating
● Extrusion speed of the hot working steel tool is therefore es-
These correspond to the specified production sential.
● A preheat temperature that is too low and a
data. During the die trial:
preheating time that is too short will give
● Section or sections should run straight with- insufficient increase in toughness. The die
out twist. can then fail in service.
● Section geometry should fulfill the quality ● If the through-heating temperature is too
requirements in terms of dimensions and ge- high and the time in the preheat oven too
ometry. long, tempering can occur. This is associ-
● Length differences between different ex- ated with a loss in strength and, in particu-
truded sections should be minimal. lar, with a diffusion of the nitrogen that ac-
Chapter 7: Extrusion Tooling / 459
Fig. 7.65 Order processing path for a semifinished product up to die manufacture
cumulates in the surface of the die after Table 7.4 gives the through-heating tempera-
nitriding into the interior of the die. The tures and times for the preheating of dies and
hardness of the bearings in the die aperture support tools. Usually, the dies are heated with
then decreases. the holders. The die holder must be preheated.
460 / Extrusion, Second Edition
Table 7.4 Preheat temperature and precheat times for aluminum extrusion tooling
Solid section Hollow section Support tool
Tool size Extrusion die and backer Porthole die Bolster
diameter, mm with die holder Bridge die with die holder Pressure ring
From To Time, h Temperature, ⬚C Time, h Temperature, ⬚C Time, h Temperature, ⬚C
... 300 2.5–3 420–450 3–4 440–460 ⬃3 350
300 500 3–4 420–450 4–5 440–460 ⬃3 350
500 700 4–5 420–450 5–6 440–460 ⬃3 350
Over 700 5–6 420–450 6–8 440–460 ⬃3 350
Source: Ames
After preheating, the die must be transported compared to aluminum extrusion because of the
into the press die holder (cassette) by the short- higher working temperatures, which can vary
est and fastest route to avoid detrimental heat from 600 to 1000 ⬚C, depending on the alloy
losses. After extrusion of the profile order, the and the extrusion parameters. Consequently,
die that has been removed must be slowly and higher hot strength and therefore more expen-
uniformly cooled. This applies in particular to sive hot working materials must be used for the
hollow dies. If the cooling is too fast and not manufacture of these tools. In spite of this, the
uniform in the air outside, then thermal stresses tools deform and wear rapidly and are therefore
can result in cracks. The cracking of a hollow frequently changed. Die inserts are used for the
die at critical areas can literally be heard. production of small semifinished product cross
sections in which the shape-producing insert is
fitted in a lower hot strength hot working ma-
terial, usually a hot working steel.
The tolerance requirements for brass section
extruded to finished sizes are not as tight as
Tools for the Extrusion of with aluminum sections; DIN 17674 applies.
Materials with However, to meet customer requirements for
tighter tolerances, the extruded sections fre-
Deformation Temperatures quently must be drawn on a draw bench. The
of 600 to 1300 ⬚C extruded dimensions and their tolerances must
be matched to the final dimensions of the sec-
tion and the drawing tolerances so that the
Martin Bauser* drawing process is successful, even with cross-
sectional variations.
Drawing, straightening, and cutting to length
7.4 Tools for Copper Alloy Extrusion as downstream operations are standard practice
for rod with small dimensions in copper-zinc
In contrast to aluminum alloys, where the alloys where the feedstock is extruded as wire.
emphasis in semifinished product production is These rods also represent the main product of
primarily on extruded profiles and where rods extruded copper alloys. Extrusion presses and
as well as tubes occupy only a small role, the tooling are specially designed for their produc-
most important products with copper alloys are tion. Indirect extrusion has proved the most
extruded rod and wire, mainly in free-machin- successful process for the production of brass
ing copper-zinc alloys. Tubes should also be in- rod, but this does place particular requirements
cluded, mainly in oxygen-free copper. The ex- on the tooling.
trusion parameters for copper alloys are Copper tube that can be cold worked without
discussed in the section “Extrusion of Semifin- intermediate annealing is usually extruded as a
ished Products in Copper Alloys” in Chapter 5. thick-wall tube in a standard dimension and
The shape-producing tools are subjected to then drawn down to different finished sizes.
significantly higher thermomechanical stresses Again, special designs for the extrusion press
and the tools have developed over time. Basi-
*Tools for the Extrusion of Materials with Deformation cally, in the rod and tube extrusion of copper
Temperature of 600 to 1300 ⬚C, Martin Bauser alloys, greater emphasis is placed on simple and
Chapter 7: Extrusion Tooling / 461
rapid die changing due to the high die wear. cated on the container side of the press front
Because the shape-producing tools of the die platen. Their arrangement only provides for
and mandrel must be lubricated, good access to movements of the tool holder transverse to the
the press is also needed. press centerline. The container can be moved
axially and sealed with its hydraulic system
7.4.1 Construction of the Tool Set for through its sealing surfaces against the sealing
Direct and Indirect Extrusion surfaces of the tool set, with a facial pressure
of at least 70 to 90 N/mm2, as shown in section
DIN 24540 applies to the tool set in the same 7.2.3. Copper alloy extrusion presses usually
way as for aluminum (Ame 71). Part 3 of this operate with conical sealing surfaces, as de-
standard summarizes the recommended tool di- picted in Fig. 7.11, 7.12, and 7.14. Today, di-
mensions for copper alloys. Before 1950, direct rect-extrusion presses for processing copper al-
extrusion for hot working of copper alloys used loys up to temperatures of 800 ⬚C are equipped
a tool head as the tool holder, and this con- with a cassette as the tool holder, and those for
tained the entire tool set. Figure 7.66 shows an processing materials at temperatures over 800
example. This tool head could be moved in ⬚C are equipped with a rotating arm, as before.
both directions along the press axis by hydrau- This contains two tool-holder positions so that
lic power. To extrude, it was moved through the it is possible to alternate between two dies.
press platen against the container that had no
axial movement, and then the transported tool
set with its sealing faces pushed against the
container sealing faces by a hydraulically op-
erated wedge. It was then in the position shown
in Fig. 7.66. From the point of view of a stable
supporting tool set providing a solid support to
the shape producing tools. This old tool holder
design was relatively underdimensioned. This
can be seen by comparing the tool set shown
in Fig. 7.66 with the tool set in the slide in a
modern standard press in Fig. 7.67. Extrusion
presses built after 1950 were fitted with die
slides or rotating arms as the tool holder, lo-
Fig. 7.67 Toot set for the direct extrusion of copper alloys
fitted in the tool holder of a die slide. (a) Axial
section through the tool stock. 1, container; 2, die holder; 3,
extrusion die; 4, backer; 5, bolster; 6, pressure ring; 7, pressure
ring as support in the press platen 8, press platen; 9, die slide.
Fig. 7.66 Tool stack for the direct extrusion of copper alloys (b) View of the three positions of the die slide. Between the die
fitted in an axially moving die head acting as the holder and the collection position for the discardand the shell
die holder. 1, container; 2, die holder; 3, extrusion die; 4, there is a baseplate against which the billet can be pierced for
backer; 5, bolster; 6, pressure bolster and die head. Source: Wie- the production of large-diameter tubes. Source: Wieland-Werke
land-Werke AG AG
462 / Extrusion, Second Edition
Easy access to the shape-forming tools that and to section 7.3.2 for the dimensions of the
must be lubricated at every extrusion is an im- die aperture for specific extrusion cross sec-
portant requirement for all tool-holder designs tions.
for the extrusion of copper alloys.
The extrusion load and container-dependent 7.4.2 Extrusion Dies and Mandrels
dimensions of the tool set for direct-extrusion for the Production of Tubes
presses for processing copper alloys (Fig. 7.4,
7.67) are specified in DIN 24540 part 3. For the Extrusion dies for processing copper alloys
200 mm container of a 20 MN extrusion press, usually have a conical outer surface face with
as an example: a conical angle of 2 to 6⬚. These dies can be
seen in the general view in Fig. 7.17 and in Fig.
● Tool set external diameter is 425 mm 7.69 and 7.70. A cylindrical die surface with a
● Tool set length is 450 mm shoulder, as is common on aluminum extrusion
● Subbolster thickness is 185 mm dies (Fig. 7.15, 7.16), is associated with the risk
● Bolster thickness is 130 mm of the extruded material penetrating between
● Die holder thickness is 125 mm the die and the die holder in the extrusion of
● Backer dimension are 130 mm diameter by copper alloys. This makes it more difficult to
95 mm thick separate the die from the die holder, but it is
● Die dimensions are 130 mm diameter by 40 used in certain cases. Copper alloy extrusion
mm thick
For indirect extrusion, the tool or die holder
is located at the head of the hollow tool carrier
stem through which the section runs. As de-
scribed in section 7.2, the tool set can be loose
in front of the hollow stem, as shown in Fig.
7.10 and 7.68, or located in a tool holder ma-
chined into the tool carrier stem, as depicted in
Fig. 7.2. Figure 7.10 gives an insight into the
principal arrangement of the tool set of an in-
direct-extrusion press for copper alloys, and
Fig. 7.68 shows the loose die holder with in-
serted flat as well as conical dies. The die hold-
ers in these tool sets usually have several func-
tions, in this case, the function of a dummy
block. The tool carrier stem itself replaces the Fig. 7.69 Extrusion die for a handrail in CuZn44Pb2 ex-
truded to the finished dimensions, and a profile
support tools needed for direct extrusion. cross section. Source: Wieland-Werke AG
The shape-producing tools for the different
extruded products are described in this chapter.
Reference should be made to “Copper Alloys”
in section 7.3.1.3 for the material flow control
(a) (b)
dies are often installed not from the exit side, used with short billets. With moving mandrels,
as depicted in Fig. 7.3 and 7.4, but from the the tip is usually flat with chamfered corners.
front, that is, from the billet side into the die Semicircular tips have proved more suitable for
holder. This applies in particular to the axially moving mandrels for working of difficult-to-ex-
moveable die head, because it simplifies die trude alloys such as the CuNi alloys. With flat
changing. The die apertures for the production tips, there is the risk that the edges will flow
of tubes follow the designs shown in Fig. 7.71. back because of the high thermal stressing of
However, the increase in the dimensions of the the mandrel surface. Hollow sections are rarely
die aperture compared to the specified dimen- produced over profiled moving mandrels since
sions of the tube external diameter is less than the small mandrel cross sections prevent the use
for the die apertures for the production of rod. of internal cooling. Figure 7.72 shows one of
An extruded rod stresses the die radially more the rare applications. Tubes with large dimen-
severely than a tube. The use of die inserts, sions are extruded over moving mandrels and
similar to the extrusion of rod and sections, is those with small dimensions over the mandrel
recommended for the production of tubes with tip. In the production of tubes with small inter-
diameters that are not too large. Their geomet- nal dimensions, an adequately stable location of
ric shape and dimensions are similar to that for the moving mandrel in the container axis can-
dies for rods. not be guaranteed. In particular, movement of
The extrusion of copper alloys does not use the mandrel from the container axis and thus an
feeder chambers as with aluminum alloy extru- unacceptable wall thickness variation of the
sion. Billet-on-billet extrusion does not work tube during the piercing of the billet cannot be
with copper alloys, because at the end of the avoided with any certainty. In these cases, ex-
extrusion process, any material remaining in the trusion must be carried out with a fixed mandrel
feeder chamber cools so rapidly that it cannot over the stepped mandrel tip, as shown in Fig.
weld with the subsequent billet. 7.20 and 7.73. The stepped mandrel tip, which
The extrusion of tubes and hollow sections is often manufactured from high hot strength
is usually carried out with a die and a mandrel. hot working material because of the high ther-
Mandrels for processing copper alloys follow momechanical stressing and the absence of in-
the designs given in section 7.3 and, in partic- ternal cooling, is screwed to the internally
ular, the designs in Fig. 7.25. The mandrels are cooled carrier mandrel, as seen in Fig. 7.25 and
usually internally cooled and have a slightly ta- 7.73. It is also possible to have the mandrel tip
pered shaft when extruding with a moving man- and the mandrel shaft as one piece for the ex-
drel. However, cylindrical mandrels can also be trusion of easily extruded copper alloys with
low deformation temperatures, as seen in Fig.
7.25. Tubes with profiled internal contours are
Fig. 7.71 Extrusion dies for the production of copper alloy Fig. 7.72 Extrusion die with cobalt alloy insert shrunk and
rods for (a) easy-to-extrude alloys and (b) difficult- peened in, together with a moving mandrel, for
to-extrude alloys. Direction of extrusion: right to left. Source: the production of the terminal section shown at right. Source:
Wieland-Werke AG Wieland-Werke AG
464 / Extrusion, Second Edition
Fig. 7.74 Extrusion die and profile cross section for the extrusion of an opened-out U-section. (a) Extrusion die and profile cross
section after extrusion and after the first and second draw. (b) Die aperture and the associated backer (support tool).
Source: Wieland-Werke AG
Chapter 7: Extrusion Tooling / 465
Fig. 7.75 Plastic deformation of the die aperture of copper section dies resulting from high thermomechanical stresses during
extrusion. Source: Kabelmetall, Osnabrück
466 / Extrusion, Second Edition
as well as the occasional risk of die failure, for to 5 mm and bearing lengths of approximately
example, in the region of the mandrel neck, are 10 mm. With the extrusion of difficult-to-ex-
extremely high. For this reason, simple tool de- trude alloys, there is the risk of plastic com-
signs with replaceable mandrels and dies are pression of the die aperture from the prolonged
used. The replaceable parts can be produced stressing that results from the high extrusion
from higher hot-working-strength materials, for temperatures and the slow extrusion speed. The
example, nickel alloys, as shown in the drawing extrusion die is therefore given a conical en-
of an old bridge die design in Fig. 7.26. trance, as shown in Fig. 7.71(b). To reduce the
For this reason, if technically possible, hol- high extrusion loads and to ensure the ease of
low copper alloy sections should be produced production of small rod dimensions, it is some-
with a die and a mandrel for process techno- times necessary to work with lubricated con-
logical reasons and, above all, for economical tainers. In this case, the use of dies with a con-
reasons. If the internal contour is circular or the ical entry is necessary (Fig. 7.17), or a die
cross section at least large enough, then extru- holder and die similar to Fig. 7.68(b).
sion with a moving mandrel can be used, as Copper alloy rod with small cross sections or
shown in Fig. 7.19. Otherwise, extrusion over diameters below 24 to 35 mm are produced
the mandrel tip as depicted in Fig. 7.20 is pre- from extruded wire on drawing, straightening,
ferred. An example is the extrusion tools shown and cut-to-length automatic machines. This
in Fig. 7.73 for the production of wristwatch wire is usually extruded through die inserts in
housings. the same way as small cross-sectional profiles.
Nevertheless, in special but rare cases, sec- The cylindrical inserts located in a hot working
tions with a small cross-sectional profile with a tool steel die body are made from high hot
profiled internal contour are extruded over a strength materials including cobalt alloys,
moving mandrel, for example, the terminal sec- metal-ceramic hot working materials, including
tion in a copper-zinc alloy shown in Fig. 7.72. the molybdenum-base cermotherm, and pure
Because it is not really possible to pierce a ceramic hot working materials such as zirco-
billet with a small cross-sectional mandrel, the nium oxide. These hot working materials usu-
billets for this process are prebored. In the pro- ally have low toughness and therefore fracture
duction of hollow sections with opposing un- quickly under the effect of tensile stresses,
equal wall thickness, as shown schematically which can develop tangentially in the die from
by the terminal section in Fig. 7.33, the mandrel the extrusion load. The die inserts in these ma-
can deflect under the transverse forces away terials are shrunk into a hot working steel die
from the material flow during extrusion and to- body and thus subjected to compressive
ward the thicker wall. This phenomenon is stresses. Under these conditions, die inserts in
avoided by including a follower adjacent to the the hot working materials mentioned can with-
thinner wall in the die, which equalizes the ma- stand up to 100 extrusions without reworking
terial flow. The necessary cross-sectional area and thus achieve many times the throughput of
of the follower must be determined by press dies in high-quality hot working steels. Obvi-
trials. ously, several inserts can be shrunk into a die
Usually, hollow sections extruded from cop- body for multicavity extrusion. The production
per alloys are subsequently cold worked, for ex- of solid dies in the materials mentioned is not
ample, drawn, to be able to achieve the tight possible because of the low toughness and also
tolerances and surface quality required by the for economical reasons.
customer. Figure 7.77 gives an overview of the differ-
ent arrangements for extrusion dies with
7.4.2.4 Extrusion Dies for the shrunk-in die inserts. Figure 7.78 illustrates the
method of assembly. Die inserts are initially
Production of Rod and Wire
produced as cylindrical bodies. The external di-
The production of extruded rod and wire in ameter is, as shown in Fig. 7.78, larger than the
free-machining copper-zinc alloys, usually bore of the die holder by the absolute interfer-
CuZn39Pb3, is quantitatively the focal point for ence fit. The shrinkage allowance depends on
the extrusion of copper alloys. For the produc- the specific coefficient of expansion of the die
tion of rod with diameters of 25 to 35 mm, solid insert and the die body material. For example,
dies are used, as shown schematically in Fig. the frequently used austenitic hot working tool
7.71. The die aperture has an entry radius of 3 steel 1.2731 has a significantly higher thermal
468 / Extrusion, Second Edition
Fig. 7.78 Production route for the production of an extrusion die with shrunk-in die insert, according to Fig. 7.77(a). Source:
Sauer
production route also fundamentally follows tions to the finished size also must be trialled
that given in Fig. 7.65. before they are first used, similar to aluminum
However, tooling for the extrusion of copper extrusion dies. The die trials usually result in
alloys is subjected to significantly higher tem- the correction of the die aperture until the de-
peratures than aluminum tooling. The extrusion sired profile dimensions are achieved. New dies
temperatures for copper alloys are well above for the extrusion of copper and low-alloyed
the tempering temperatures of the classic hot copper alloy profiles also must be conditioned,
working tool steels. Consequently, the classic as described in section 7.4.2.2.
hot working steels cannot be used for all ap- Compared to aluminum extrusion tooling,
plications. Instead, the manufacture of copper higher thermomechanical stresses occur in the
extrusion tooling requires the use of higher hot die aperture of copper extrusion dies, and this
strength tool materials, including austenitic hot means that wear-resistant surface treatments are
working steels, cobalt-base hot working mate- less effective. Surface treatments of hot work-
rials, nickel-base hot working materials, molyb- ing tool steel extrusion dies, for example, ni-
denum-base metal-ceramic materials, and pure triding, can be excluded because of the tem-
ceramic hot working materials. These materials perature-related rapid diffusion of nitrogen into
are discussed in the detail in the section “Hot the interior of the die steel. Even chemical va-
Working Materials for the Manufacture of Ex- por deposition coatings do not offer any advan-
trusion Tooling” in this Chapter. tages. The coatings are destroyed by the fre-
quent reworking of the die apertures.
Before use, the shape-producing tooling of
7.4.3.2 Use of the Extrusion Tools
the extrusion die and the mandrel are heated in
Again, the handling criteria described in sec- a chamber furnace up to temperatures of 450
tion 7.3.4.3 for aluminum extrusion tools apply. ⬚C for 2 to 4 h holding time, depending on the
Extrusion dies for the production of brass sec- size of the tooling. Complete through-heating
470 / Extrusion, Second Edition
over the cross section of the tool is necessary at these temperatures, coats the billet and the
to avoid tool failure as a consequence of inade- container liner surface and thus separates the
quate ductility in the heated tool. If the heating flowing extruded material from the surface of
time is too short, then through-heating over the the shape-forming tooling during the extrusion
full cross section will not be achieved. If the process. Glass has poor thermal conductivity
heating temperature is too high, then oxidation and therefore acts as an insulator. In addition,
of the tool surface will occur. Temperatures that the use of glass lubrication allows high extru-
reach the tempering range of the hot working sion speeds to be used, which allows the effec-
material will result in a reduction in strength. tive exposure of the tooling to the temperature
To avoid unacceptable heat loss from the shape- to be kept short. The extrusion of significantly
producing tool to the support tooling, the latter shorter section lengths compared to aluminum
should also be preheated. This applies in par- and copper alloys helps in this context. In the
ticular to backers that support the die under the deformation zone, quasi-adiabatic conditions
extrusion load. The tooling should be loaded as
exist, and as a result, temperatures up to 1300
quickly as possible in the die or tool holder
⬚C can occur. The thermal stressing of the tool-
after removal from the preheat furnace.
During the processing of an order on the ex- ing, which only lasts for a few seconds, can be
trusion press, the shape-producing tool is re- extremely high, even with the glass insulating
moved after a few extrusions and replaced with layer and the high speeds. The extrusion die can
a tool held in the preheat furnace. Larger orders only withstand a maximum of three extrusions
therefore require more tools in circulation. The before being reworked. This requires a large
removed tooling is cleaned and measured and number of extrusion dies to be available, de-
the bearing quality checked. If necessary, the pending on the specific order size.
entire shape-producing area, which can exhibit Direct contact of the extruded material with
plastic deformation resulting from the high the tooling surface inevitably results in severe
thermomechanical loading, must be reworked. damage to the extrusion tooling and the ex-
The cooling of extrusion tooling after use re- truded product. Laminar flow of the extruded
quires special care because of the significant material must be ensured to avoid a breakdown
heating during the extrusion process. It should of the glass film surrounding the material flow.
not be too rapid or asymmetrical, which can Sharp-edged transitions in the contact surfaces
occur if the hot die is placed on the cold floor. of the die in the entry and in the die aperture
Instead, careful, controlled cooling in sand or must be avoided at all costs. For rod, tube, and
ash is advisable. Large mandrels can be cooled section dies, conical and angled as well as
by standing on their end to avoid distortion. smooth transitions are necessary, as seen in Fig.
After cooling, the tools are stored. They 7.24 and 7.79. Fluid friction between the ex-
should first be cleaned and then shot blasted truded material and the die bearing surfaces
with sand or other materials, and the bearing dominates and hardly allows any effective con-
surfaces should be honed to bring them back trol of the material flow in the die apertures, in
into a usable condition. If necessary, this also contrast to the extrusion of aluminum and zinc-
includes reworking of the die aperture. Even containing copper alloys. This theme is dis-
with severe plastic deformation in this region, cussed in section 7.3.1 and specifically for
a die can be brought back to a usable condition
glass-lubricated extrusion in section 7.3.1.3.
by a subsequent erosion operation.
Tubes and hollow sections are usually pro-
duced with moving mandrels and not over a
7.4.4 Tooling for the Glass-Lubricated mandrel tip. The mandrel shanks are slightly
Extrusion of Titanium, tapered, similar to the production of copper al-
Nickel, and Iron Alloys loy tubes, and internally cooled, as depicted in
Titanium-base extruded alloys with defor- Fig. 7.25. Because the outer surface is sprayed
mation temperatures of 900 to 1150 ⬚C, nickel- with a cooling medium to break off the glass
base alloys with deformation temperatures of layer at the end of every extrusion, mandrels
900 to 1280 ⬚C, and iron-base alloys with de- are also externally cooled. For this reason,
formation temperatures of 1000 to 1300 ⬚C can small extrusion mandrel cross sections and also
only be extruded with glass lubrication. The massive mandrel shanks can be used without
glass of a suitable composition, which is liquid internal cooling.
Chapter 7: Extrusion Tooling / 471
hot working tool steels, which are used for the did result in significantly higher outputs, par-
glass-lubricated extrusion of iron alloys, cannot ticularly with molybdenum alloy dies, but no
withstand these contact times well. Through- economic advantage over extrusion dies in hot
puts approximately twice as high can be working steel because of the higher material
achieved with dies in Nimonic 90. Otherwise, and production costs. Even coating the die sur-
the general considerations for tooling for glass- faces has not proved successful. Frequently, the
lubricated extrusion apply. marked difference between the thermal expan-
sion of the coating and the tool material under
7.4.4.4 Tooling for the high thermal loading results in shear
stresses so high that the wear-reducing coating
Extrusion of Iron Alloys
breaks off from the die. Consequently, the much
Iron alloys require high deformation tem- cheaper hot working steel 1.2343 is still pri-
peratures, and this necessitates rapid extrusion marily used. Mandrels for alloy steel tube pro-
to avoid high heat losses. These extrusion con- duction are also made in the steels 1.2343 and
ditions can only be realized by glass-lubricated 1.2365 (H10 or T20810). They usually have
extrusion. More detailed information can be conical shanks. The mandrel life is similar to
found in the section “Extrusion of Iron Alloy the die life of approximately 400 extrusions,
Semifinished Products” in Chapter 5. helped by the internal and external cooling.
Tooling for the Extrusion of Alloy Steels. Extrusion Tooling for the Production of
Alloy steel tubes are only produced with extru- Steel Sections. Obviously, the high extrusion
sion dies and mandrels. Porthole and bridge temperatures used allow only the production of
dies, which are used for the manufacture of simple steel profile cross sections by extrusion.
tubes and hollow sections in aluminum alloys The focus of profile production is therefore on
and occasionally also for copper alloys, are not solid sections. At the same time, hollow sec-
suitable for the extrusion of iron alloys because tions with simple cross-sectional geometry can
of the high thermomechanical stresses. The ex- be produced using profiled mandrels. In certain
trusion dies used for the production of alloy cases, it is also possible to extrude over a pro-
steel tubes are usually made from hot working filed mandrel tip. Intricate profile cross sections
tool steels and have the usual conical entry for cannot be produced.
lubricated extrusion, with an opening angle of Usually, single-cavity extrusion is carried
generally 120⬚. The dies are loaded either from out. This does not exclude multicavity extru-
the billet side or the exit side, depending on the sion of up to six profiles for small cross sec-
design of the tool or die holder. They are lo- tions. Long conical entries, as with round die
cated by a conical or a cylindrical surface with apertures for the production of tubes, cannot be
a shoulder. Figures 7.16, 7.17, and 7.79 show produced. Only limited material flow control
these methods of location. Fast and, if neces- can be achieved using angled and heavily
sary, automated loading and unloading is im- rounded entry areas, as seen in Fig. 7.24 and
portant for tool changing because of the stress- 7.79. This also applies to the equalization of the
related frequency. At the end of the extrusion material flow in the die aperture by bearings of
process and removal of the section and discard, different lengths. This method of control, which
the tool holder, either a rotating arm or tool works well for the extrusion of aluminum sec-
slide, is moved out of the press. After the die tions, has practically no effect because of the
has been removed, it is cooled in water, in- low friction from the glass lubrication. Conse-
spected, and reused after preheating. Dies in the quently, large variations in cross-sectional ge-
hotworking steel 1.2343 (H11 or T20811 simi- ometry must be avoided in the design of steel
lar U.S. grade) can be used up to 40 times in profiles, because the resultant variations in the
this way before they must be reworked, when material flow can be almost impossible to bal-
they are usually opened out to a larger tube di- ance.
ameter. In this way, a single die can last for up Short lengths—rarely over 15 m—are usu-
to 400 extrusions with several rebores. ally extruded to limit the high thermomechan-
Numerous investigations have been carried ical stressing of the tooling. In spite of this and
out with other hot working materials, including the related short contact time, the die aperture
those based on cobalt, nickel, and molybdenum, can close in from the front of the extrusion to
to reduce the number of dies in circulation by the back as a result of plastic deformation. The
increasing the service life. These investigations hot die material in the entry area of the die be-
Chapter 7: Extrusion Tooling / 473
gins to flow into the die aperture, as seen, for cess and are indirectly involved with the
example, in the die aperture area of dies for the deformation. The tool life is limited and de-
production of copper profiles in Fig. 7.75. The pends mainly on the deformation tempera-
shape-producing areas of a die do not deform ture and the extrusion load, FSt. Tool chang-
uniformly. The projecting regions in the die ap- ing, for example, container replacement,
erture that are partly surrounded by the flowing must be carried out in the shortest time pos-
material are particularly affected. This can sible.
clearly be seen in Fig. 7.24 and 7.79. Hot work- ● Tooling that does not come into contact
ing tool steels only have a fraction of their hot with the extruded material and has either a
strength at these high working temperatures. support or an auxiliary function. This in-
Naturally, the producer of extruded steel sec- cludes the mantle and the liner holder. The
tions puts considerable effort into increasing the extrusion stem, the bolsters, and the man-
service life of the extrusion tools. The profile drel holder also come into this category. In
dies are also more sensitive to high thermo- addition to the supporting role, the container
mechanical stresses than tube extrusion dies. In also has temperature-controlling tasks, in-
extensive studies [Bra 66], dies in numerous cluding heating and cooling. These tasks are
classical hot working steels, austenitic hot very important because they provide the
working steels, and cobalt, nickel, and molyb- possibility of keeping down the cost of the
denum hot working materials were tested. container, which is an expensive tool. A
The best results of these hot working mate- container design matched to this application
rials were obtained with the molybdenum ma- is a requirement for the economic efficiency
terial titanium-zirconium-molybdenum (TZM) of the extrusion press.
in the precipitation-hardened condition. The
service life of the experimental dies could be A tooling set with a fixed dummy block for
extended to well over 100 extrusions without direct extrusion is shown in Fig. 7.80. It cor-
reworking. At the same time, there was no eco- responds to the tool set for the extrusion of easy
nomic advantage over hot working steel dies. and moderately difficult-to-extrude aluminum
More economic is a die in cast steel 1.2343. alloys. A loose dummy block must be used for
This hot working steel is inexpensive, easily the extrusion of copper alloys.
machined, and has a relatively good thermal The tool set in Fig. 7.81 is for the indirect
conductivity. The production of the die follows extrusion of copper alloys. A cleaning stem
the route described previously. If the die aper- with a cleaning block can also be used to re-
ture has deformed under high thermomechani- move the shell.
cal stresses after one to three extrusions, it can The tool set in Fig. 7.82 is for the direct tube
be brought back to a suitable condition for pro- extrusion of copper alloys. A cleaning block to
duction by welding and then erosion and me- remove the shell is also used.
chanical machining [Lau 76]. Figure 7.83 shows a tool set for the indirect
extrusion of aluminum alloy tubes.
Tool sets for direct tube extrusion, as also
7.5 Extrusion Tools for shown in Fig. 7.1, differ from the usual tooling
Indirect Shape Production, for direct extrusion only in the mandrel and the
Auxiliary and Support Tooling resultant changes in the stem and the dummy
block. This applies to both direct and indirect
Extrusion tools for indirect shape forming as extrusion. While in indirect tube extrusion a
well as the associated auxiliary and support sealing tool is preferred for copper alloys, a
tooling are numerous and fulfill a wide range press with a sealing stem is usually used for
of applications. Table 7.5 gives an overview. aluminum alloys, as shown in Fig. 7.8. DIN
Extrusion tools for indirect shape forming are 24540 provides a reliable basis for the design
designed to be replaceable and are located in and dimensioning of the extrusion tools for di-
movable tool carriers, including the container rect extrusion and direct tube extrusion, as al-
housing, moving crosshead, piercing crosshead, ready mentioned in section 7.2.1. The main di-
cassette, and so on. The functions can be clas- mensions of the tools, such as the container
sified into: internal diameter, container length, extrusion
● Tools that come into direct contact with the stem, dummy block, and mandrel, are specified
extruded material during the extrusion pro- here. They are based on practical experience
474 / Extrusion, Second Edition
Table 7.5 Overview of the direct and indirect extrusion tools for indirect shape forming
(continued)
(a) Resistance heating in container holder. Source: Groos
and have a direct relationship with the smallest container length is five times the container in-
container diameter that is obtained with a spe- ternal diameter for pi ⳱ 1000 N/mm2, as rec-
cific pressure (press power relative to the con- ommended in DIN 24540. There is no data for
tainer cross section) of 1000 N/mm2 at the max- extrusion tooling for indirect extrusion and in-
imum possible extrusion press load. The direct tube extrusion in DIN 24540. The design
Chapter 7: Extrusion Tooling / 475
dp a b bm bi c es e
dp = support tooling; a = die; b = container; bm = mantel; bi = liner; c = billet; es = fixed dummy block; e = extrusion stem
Fig. 7.80 Complete tool set for direct extrusion of aluminum alloys. Source: Groos
476 / Extrusion, Second Edition
Fig. 7.81 Complete tool set for indirect extrusion of copper alloys. Source: Groos
Fig. 7.82 Complete tool set for direct tube extrusion of copper alloys. Source: Groos
Fig. 7.83 Complete tool set for indirect tube extrusion of aluminum alloys. Source: Groos
and dimensioning of indirect-extrusion tooling bore sufficient to ensure economic wire pro-
is based on the bore of the hollow stem. The duction of copper alloys such as brasses. The
smallest container diameter with a specific pres- container length is given as 6.3 times the con-
sure of 710 N/mm2 gives an extrusion stem tainer internal diameter for pi ⳱ 710 N/mm2.
Chapter 7: Extrusion Tooling / 477
The resultant billet length has proved successful during the screwing in and out of the mandrel
on a number of indirect-extrusion presses. into the mandrel holder. In order to speed up
the screwing in and out of the mandrel, the
7.5.1 Mandrel Holder and mandrel rotation system is fitted with a drive
Mandrel Cooling that can also be used for positioning. The cur-
rent methods of fixing the mandrel to the man-
The schematic drawing of different mandrel drel holder are:
mountings in Fig. 7.84 shows the possible basic
mandrel designs obtained by adapting the man- ● Parallel threads with double fit (used most
drel holder. often)
The mandrel mounting, consisting of the ● Taper threads with double fit (not often
mandrel holder and the piercer bar, positions seen)
and locates the mandrel needed for the produc- ● Bayonet lock (expensive and not suitable
tion of seamless tube and hollow sections, as for transferring large loads)
shown in Fig. 7.25. It joins the mandrel with ● Mandrel with a fit and a shoulder as well as
the piercer system or with the mandrel mover a threaded sleeve with a double fit (suitable
of the extrusion press. The mandrel that is di- for small mandrels)
rectly involved in the deformation has a limited
life because of its function in the die area at Care should also be taken to ensure that the
high deformation temperatures. In addition, the forces developed do not damage either the man-
wide range of extruded products requires a drel holder or the piercer bar in the piercer cross
large number of mandrels of very different head. Failure of a mandrel is preferred to dam-
shapes and sizes. To minimize the downtime age to the expensive mandrel holder and piecer
when changing tooling, the method of fixing bar. The stresses developed during the extrusion
must be selected to enable rapid mandrel process make it necessary to use high-strength
changing. steels similar to those used for the mandrels for
The dimensions of the mandrel holder are de- the mandrel holder. Extremely high stresses can
termined by the size of the stem bore and by develop in the interface between the mandrel
the piercer or mover stroke. The diameter of the and the mandrel holder in the tube extrusion of
production-specific mandrel determines the size aluminum and magnesium alloys over large sta-
of the dummy block bore. Experience has tionary mandrels. The resultant high tensile
shown that the guiding of the mandrel holder stresses on the mandrel and its holder require
in the extrusion stem bore must have sufficient special attention. In this case, monitoring of the
clearance. It should be located at the front end forces that occur during extrusion within the
of the mandrel holder. In addition, the mandrel tube press can be used. With small- and me-
holder must be secured to prevent loosening dium-sized mandrels, the mandrel holder is se-
Fig. 7.84 Standard mandrel holders for mandrels of different sizes. Source: Groos
478 / Extrusion, Second Edition
cure against damage because of the steps in the mandrel. This must be large enough for the cen-
dimensions. trally aligned internal cooling tube and for suf-
The design of the mandrel holder must be ficient feed and return of the cooling medium.
matched to the dimensions, the shape, and the The internal bore of the mandrel must be dead
material of the connecting components to en- center to ensure that thermal influences do not
sure that the mandrel holder is less highly affect the central location of the mandrel during
stressed than the mandrel. The piercer bar is production. The cooling tube must be fitted
part of the piercing system and is not as highly with plug fittings for rapid tool changing and
stressed as the mandrel holder. The threaded be centrally located. The piercer bar, which is
connections must be reliable. The threads must connected to the cooling system, also has a tube
not loosen or seize. To achieve an acceptable plug fitting. The cooling medium is treated and
service life and reliability in operation, all in- heated water in a closed circuit. In addition to
fluences, including notches, turning marks, and the cooling and heating function, care must be
rough surfaces, that could result in fatigue fail- taken to ensure that no cooling water remains
ure must be avoided. The shape and positional in the tube and the tooling before changing a
tolerance according to DIN 7184 in terms of mandrel. The mandrel cooling system should be
straightness, squareness, concentricity/coaxial- as close to the press as possible in an accessible
ity, and runout must be maintained to tight cellar.
limits.
For tube extrusion with mandrels according 7.5.2 Dummy and Cleaning
to Fig. 7.82, a single extrusion stem with a bore Blocks for Round and Oval
that is sized for a suitable mandrel holder suf- (Rectangular Billet) Containers
fices for one container bore. The mandrel
holder shown in Fig. 7.84 is suitable for use For direct extrusion, the following are used:
with most mandrels with different dimensions. ● Loose dummy block
Monitoring the tensile and compression stresses ● Fixed dummy block
in the mandrel during piercing and tube extru- ● Combination dummy and cleaning block
sion also protects the mandrel holder against
overloading. Mandrel holders are usually one For indirect extrusion, the following are
piece. Only when large and small tubes are ex- used:
truded on a tube press can it be advisable to use
● Die block (single piece for aluminum alloy
a two-piece mandrel holder, as shown in Fig.
7.84. This multipart design enables the tool cost extrusion, as shown in Fig. 7.83, and mul-
to be reduced and the tool changing to be less tipart with inserted die for copper alloy ex-
involved. trusion)
● Sealing block that seals the container bore
External mandrel cooling is used on vertical
tube presses with small mandrels. On horizontal Only the most common block designs are dis-
tube presses, there is the risk that the horizon- cussed because of the wide range of dummy
tally located mandrel is not uniformly cooled blocks and cleaning blocks used.
on the surface and thus bends. In addition, it is
also possible for thermal stress cracks to form
7.5.2.1 Dummy and Cleaning
on the mandrel surface after a relative short
time as a consequence of exceeding the resis- Blocks for Direct Extrusion
tance of the hot working steel to temperature Loose dummy blocks are always used with a
fluctuations (Fig. 7.119). Internal cooling of the shell for extrusion. The dummy block thickness
mandrel, as depicted in Fig. 7.25, is standard is based on a value of 0.5 to 0.7 times the con-
technology in the extrusion of copper alloys. tainer bore. Both the extrusion temperature and
The cooling must be the most effective in the the extrusion load transfer to the stem influence
area of the deformation zone of the mandrel or the thickness of the dummy block, and this
mandrel tip. The cooling medium is fed into the must be taken into account. The diameter of the
front portion of the mandrel through the cooling front land determines the shell thickness during
tube. The return flow takes place between the extrusion. The thickness of the shell itself de-
cooling tube external diameter and the bore of pends on the billet quality. The length of the
the mandrel and the mandrel holder, which is front land is between 0.25 and 0.4 times the
axially bored to allow internal cooling of the dummy block thickness and depends on the ma-
Chapter 7: Extrusion Tooling / 479
terial being extruded. After each extrusion, the Expanding and solidified dummy blocks
loose dummy block must be separated from the Expanding fixed dummy block
epi epa sp e ha
discard and the shell, and consequently, four to
six dummy blocks must be in circulation, as
described in section 6.1.1.3 “Auxiliary Equip-
ment for Direct Extrusion.”
Fixed dummy blocks, whether for round bil-
Solid fixed dummy block
lets or billets with an oval cross section, be di- es e ha ld es e ha
vided into two functional types: expanding or
solid. They vary considerably in design. The
expanding fixed dummy block is used exclu-
sively for the extrusion of easy and moderately
difficult-to-extrude aluminum alloys. In the ex- epi = internal piece; epa = external piece; sp = clearance;
e = extrusion stem; ha = retaining bar; es = fixed dummy block;
trusion of aluminum alloys, the residual mate- ld = mandrel
rial layer in the container bore is shaved off (a)
during the return of the previously used solid
fixed dummy block. A ring of the shell then
forms behind the land. As extrusion continues,
a correspondingly large number of shell rings
form that result in problems if they are not re-
moved. This resulted in the development of dif-
ferent expanding fixed dummy blocks in one-
piece and multipiece designs. In order to avoid
the undesirable shell ring, the front external di-
ameter of the fixed dummy block must be larger
during extrusion than on the return. In the sin-
gle-piece design, the front surface of the block
is designed so that the outer diameter expands
under the extrusion load. This increase in the
external diameter must take place in the elastic
range of the dummy block material. Sufficient
external diameter expansion can be achieved
with a suitable shape and no critical notch ef-
fects, for example, from the machining. This
solution is associated with a larger discard be-
cause of the machined profile of the front face.
The multipart design in Fig. 7.85 enables a flat
face with no machined profile to be used. The
desired fixed dummy block effect of the exter-
nal diameter being smaller during the return is
achieved relatively successfully by a conical in- Fig. 7.85 (a) Schematic design of a fixed dummy block.
Source: Groos. (b) Photograph of a multipart fixed
sert and a matched external ring. However, the dummy block. Source: CLECIM
individual components must be matched to give
an acceptable service life in production. Incor-
rect mechanical properties in the conical com-
ponents can reduce the life of the dummy block The cleaning blocks are ring shaped and have
considerably. The fixed dummy block in the the same main external dimensions as the loose
multipart design is used almost exclusively in dummy blocks. This is necessary because of the
the extrusion of aluminum alloys. The solid common recycling in the auxiliary system. The
fixed dummy block is always one piece. It is external diameter is dimensioned so that the
used for the extrusion of copper alloys with a shell can be removed completely and reliably
low extrudability without a shell, particularly from the container liner. Often, it is slightly
tube extrusion and for steel extrusion. While the oversized. In this case, it must have a diagonal
front surface is conical for copper alloys, flat slit in order to elastically conform to the liner
front surfaces with large radii to the external wall that must be cleaned like a spring (Fig.
diameter are used for steel. 7.86).
480 / Extrusion, Second Edition
Fig. 7.86 Schematic drawings of typical loose dummy blocks and cleaning blocks. Source: Groos
The combined dummy block and cleaning A big advantage of the combination dummy
block is preferentially used when the shell vol- and cleaning block is the simplified operation
ume is small and can be removed from the shell of the press. The time and manipulation re-
chamber without difficulty (Fig. 7.87). This is quirement as well as the cleaning time needed
the case with short billets for the extrusion of to use a separate cleaning block are eliminated,
tubes. Guiding the mandrel through the block as seen in the operating sequence in Chapter 6.
and locating it in the center of the container
bore gives the optimal requirements for central
7.5.2.2 Dummy Blocks and Cleaning
piercing of the billet. The container bore and
the combination dummy and cleaning block Blocks for Indirect Extrusion
must be in good condition. Wear that impairs The loose dummy block acts as the die block
the bore geometry is unacceptable. In particular, or the sealing block for the sealing stem, as
the combination dummy block and cleaning seen in Fig. 7.83. The loose die block is pre-
block can be successfully used with thin shells. ferred for the indirect extrusion of copper alloys
Problems occur when the shell volume in the and aluminum alloys (Fig. 7.88). The die block
shell chamber is too severely compacted, and thickness depends on the size of the die, the die
removal of the shell from the block becomes support needed, and the size of the bore in the
difficult. The time needed to clean the shell die-carrying stem, which determines the space
chamber is then too long. available for the emerging extruded product.
651.67
535.17
418.67
302.17
185.67
X
Z
69.17 Shell thickness Shell recess
Fig. 7.87 Finite element study (Left); (Source: Schloemanna) and sketch (right) of a combination dummy and cleaning block for
tube extrusion. The size and shape of the shell chamber produce stress concentrations that must be limited. In this
example, the maximum equivalent stress at the root of the shell chamber is approximately 850 N/mm2.
Chapter 7: Extrusion Tooling / 481
Fig. 7.88 Sketch of a combination die and cleaning block for extrusion of aluminum alloys. Source: Groos
Figures 7.2 and 7.9 show this clearly. Both the The resultant small shell volume of the pre-
deformation temperature and the extrusion load machined billets can be collected in the shell
transfer onto the hollow tool carrier stem (ex- chamber of the die block. In the indirect extru-
trusion stem) influence the thickness of the die sion of copper alloys, the combination die and
block, which is important for the quality of the cleaning block is preferred when small shell
extruded product and for the service life of the volumes occur. The separate cleaning block is
tooling, and therefore must be taken into con- required in copper alloy extrusion when long
sideration. The diameter of the front land de- billets are extruded and a thick shell is pro-
termines the thickness of the shell in indirect duced. The shell volume is relatively large be-
extrusion. The thickness of the shell itself de- cause of the long billets. The shell then must
pends on the quality of the billet surface, which be removed in an additional operation. The
must be good in indirect extrusion for process combination die and cleaning block do not dif-
technological reasons. The length of the front fer from the cleaning discs used in direct extru-
land depends on the material being extruded. sion.
The thickness of the sealing block corresponds
to the thickness of a loose dummy block used 7.5.3 Extrusion Stems for
in direct extrusion. The number (one or two) of Round and Oval Billet Containers
the die blocks (die holder) in use depends on
the order size. Thus, two die blocks can be For direct extrusion, the following are used:
used. The productivity with two die blocks is ● Extrusion stem as a solid stem for the ex-
increased because of the reduced dead cycle trusion of round billets
time during a production cycle. A single loose ● Extrusion stem as a solid stem for the ex-
die block in indirect extrusion is practical only trusion of rectangular billets (billets with an
for small orders. oval cross section)
The fixed dummy block as a die block (die ● Extrusion stem as a hollow stem for tube
holder) is not used in the indirect extrusion of extrusion
copper alloys. In the indirect extrusion of alu-
minum alloys, the use of fixed die blocks is, in For indirect extrusion, the following are
contrast, widespread. The attachment to the hol- used:
low tool carrier stem (hollow stem) represents ● Die carrier stem (hollow stem) for extrusion
a weak point and results in additional stress and tube extrusion
concentrations in the highly stressed tooling. ● Sealing stem to seal the container bore
Also, the resultant shell ring in the die block ● Cleaning stem to remove the shell from the
area must be removed within the press. How- container bore
ever, the auxiliary systems are less expensive
because the circulation system for the die block Because the method of locating the stem de-
is not required. pends on the press manufacturer, different sys-
The combined die and cleaning block is used tems are met in practice. The stem location is
in the indirect extrusion of aluminum alloys. designed as a quick-fit connection for rapid
482 / Extrusion, Second Edition
Fig. 7.90 Equivalent stresses at the transition to the stem foot of an extrusion stem for indirect extrusion. Source: SMS Schlomann
Chapter 7: Extrusion Tooling / 483
Table 7.6 Dimensions of extrusion stems for indirect extrusion for specific press pressures
Stem dimensions and stem loads
Press capacity, MN
12.5–14 16–18 20–22.5 25–28 31.5–36 40–45 50–56
Shank length, mm
Specific extrusion pressure, N/mm2 1000 1120 1250 1400 1600 1800 2000
315 Outside diameter, mm 230 259 293 328 373 417 467
Inside diameter, mm 175 195 220 245 280 310 350
Compressive stress, N/mm2 800 789 765 750 744 737 746
400 Outside diameter, mm 206 230 259 293 328 373 415
Inside diameter, mm 145 160 180 205 230 265 290
Compressive stress, N/mm2 836 840 826 814 827 801 809
500 Outside diameter, mm 185 206 230 259 293 328 373
Inside diameter, mm 115 125 140 160 180 200 225
Compressive stress, N/mm2 849 855 860 859 846 848 806
630 Outside diameter, mm 165 185 206 230 259 293 328
Inside diameter, mm 85 95 105 115 130 150 165
Compressive stress, N/mm2 891 901 912 899 901 904 887
710 Outside diameter, mm 155 175 195 219 244 274 308
Inside diameter, mm 65 70 80 90 100 110 125
Compressive stress, N/mm2 900 890 906 895 913 910 900
Source: Groos
Stem loading
Euler’s buckling type 3 Deflective curves for stem analysis
A B A l B
l
x
f x1
a)
e F wx1
FSt
wmax
wx
M
b)
f x2 wx2
wmax
c)
w
xK
● Squareness of the billet end faces lation give an additional degree of safety for
● Structural homogeneity of the billet the stem.
● Uniformity of the temperature over the bil- The stability calculation is derived as fol-
let cross section lows.
● Billet clearance in the container For given dimensions and loadings, the trans-
verse force, F, in the most unfavorable case
The eccentric forces, which depend on the with an eccentricity, e, is calculated. Starting
operational conditions, are used to calculate the from a cantilever clamped at one end, the cal-
buckling of the extrusion stem. The geometri- culation of statistically indeterminate systems
cally possible eccentricity at full extrusion load with the solution for simple statistically inde-
is always less than 25% of the billet clearance. terminate systems [Gie 95] as well as the for-
Thus, the recommended values for the calcu- mula for the corresponding deflection line [Dub
Chapter 7: Extrusion Tooling / 485
86] gives useable results for the extrusion stem, stem length, and approximately 290 ⬚C at the
corresponding to the deflection lines a, b, and stem foot. No higher temperature was detected
c in Fig. 7.92: in the stem bore as a result of the passage of
the extruded material. A definite temperature
F ⳯ l3 3
冤 冢冣冥
x x decrease develops from the front face toward
wx1 ⳱ ⳮ ⳯ 2ⳮ 3 Ⳮ the stem foot, depending on the operating con-
6 ⳯ E ⳯ Iy l l
ditions. In any case, the temperature of the stem
M ⳯ l2
2 in indirect extrusion should be taken into ac-
wx2 ⳱
2 ⳯ E ⳯ Iy 冤
x
⳯ 1 ⳮ2 Ⳮ
l
x
l 冢冣冥 count. Basically, the stem and, in particular, the
die carrier stem should be preheated to avoid
The deflection line w for buckling loading F damage to the stem.
with the eccentricity e, that is, M ⳱ F ⳯ e, is The maximum buckling load occurs at one-
the addition of wx1 Ⳮ wx2: third of the buckling length from the front face.
This region is unlikely to be overheated by the
F ⳯ l3
working temperature. Thus, there is no signifi-
w ⳱ wx1 Ⳮ wx2 ⳱ ⳮ cant decrease in strength. Failures from accept-
6 ⳯ E ⳯ Iy
able buckling loading are not known. Failures
3
M⳯ l
冤 Ⳮ冢 冣冥Ⳮ
2
x x that have occurred are almost always attribut-
⳯ 2ⳮ3
l l 2⳯ E⳯I y able to unacceptable stress concentrations, ther-
2 mal shocks from the use of cold stems in the
⳯ 冤1 ⳮ 2 Ⳮ 冢 冣 冥
x x
press at working temperature, unacceptable
l l
transverse loads from operational defects, and
production errors. In addition, high thermal
For a centrally guided buckling beam, wA ⳱ 0
stress fluctuations result in surface cracking.
and x ⳱ 0. The resultant transverse force Q ⳱
F is:
7.5.3.4 Examples of Stem Calculations for
3 ⳯ FSt ⳯ e Direct and Indirect Extrusion
F⳱
2 ⳯l Figure 7.93 shows typical extrusion stems.
Example 1: Solid Stem for a 1000 N/mm2
The resultant maximum deflection, wmax, is Container for a 31.5 MN Direct-Extrusion
given by: Press.
FSt ⳯ e ⳯ l2
wmax ⳱ Material parameters
27 ⳯ E ⳯ Iy
Material 1.2344 (X40CrMoV5.1)
Strength 1700 N/mm2
Provided the stem dimensions for direct ex- E modulus 210,000 N/mm2 (room temperature)
trusion match the requirements of DIN 24540, 195,000 N/mm2 (350 ⬚C)
and those for indirect extrusion follow Table Dimensions
7.6, then a stability analysis is not required. The Stem length 1300 mm
temperature influence on the stem from the bil- Shank diameter 195 mm
let is reduced by the dummy block in direct
extrusion or by the die block (die holder) in
indirect extrusion. The temperature influence Strength Analysis. The actual extrusion load
from the container is not very high. Tempera- differs in practice from the nominal press load.
ture measurements on the stem of an indirect It is usually higher. Compared to the nominal
extrusion press in the indirect extrusion of alu- press load of 31.5 MN, the actual load can be
minum alloys gave approximately 300 ⬚C on 32.29 MN, which is an increase of 2.5% in the
the end face. The temperature of the stem shank press load. Consequently, the compressive
at a distance of one-third of the stem length stress on a solid stem with a diameter of 195
from the front face was approximately 200 ⬚C mm is not equal to 1055 N/mm2, as given in
and approximately 100 ⬚C at the stem foot. In DIN 24540, but:
the indirect extrusion of copper alloys, stem
shank shaft temperatures were measured at 360 3.229 N ⳯ 107 ⳯ 4
rD ⳱ 1081 N/mm2
⬚C at the front face, 320 ⬚C at one-third of the 1952 mm2 ⳯ p
486 / Extrusion, Second Edition
Solid stem
ø ø 1) Extrusion stem for the extrusion of
195 410 wire, bar, and sections
1000
1300
With a minimum yield strength of 1700 N/mm2 rmax ⳱ 1081 N/mm2 Ⳮ 152.49 N/mm2
for the stem material 1.2344, the maximum per- ⳱ 1233 N/mm2
mitted loading is:
The safety factor [Dub 86] can be calculated
r0.8 ⳱ 1700 N/mm2 ⳯ 0.8 ⳱ 1360 N/mm2 as:
冪
1.95 N/mm2 ⳯ 105 ⳯ 7.098 mm4 ⳯ 107
3 ⳯ 3.229 N ⳯ 107 ⳯ 3 mm p2 ⳯ 2 ⳯
F⳱ ⳱ 111.8 kN 3.229 N ⳯ 107
2 ⳯ 1300 mm ⳱ 2909 mm
Strength Analysis. The actual extrusion load The safety factor can be calculated as:
differs in practice from the nominal press load.
It is usually higher. Compared to the nominal 1360 N/mm2
Sr ⳱ ⳱ 1.012 N/mm2
press load of 31.5 MN, the actual load can be 1344 N/mm2
32.29 MN, which is an increase of 2.5% in the
press load. Consequently, the compressive SK ⳱
stress on a hollow stem with a diameter of 195 p2 ⳯ 2 ⳯ 1.95 N/mm2 ⳯ 105 ⳯ 7.038 mm4 ⳯ 107
mm and a bore of 59 mm is not equal to 1161 3.229 N ⳯ 107 ⳯ 13002 mm2
N/mm2, as given in DIN 24540, but: ⳱ 4.964
3.229 N ⳯ 107 ⳯ (3 mm Ⳮ 0.442 mm) With a minimum yield strength of 1600 N/mm2
rB ⳱ for the stem material 2343, the maximum per-
7.219 mm3 ⳯ 105
mitted loading is:
⳱ 153.958 N/mm2
r0.8 ⳱ 1600 N/mm2 ⳯ 0.8 ⳱ 1280 N/mm2
rmax ⳱ 1190 N/mm2 Ⳮ 153.985 N/mm2
⳱ 1344 N/mm2 The safety factor is then:
488 / Extrusion, Second Edition
冪
42712 mm2 changed, then a preheated stem should be avail-
lperm ⳱ ⳱ 1920 mm
4.947 able.
Chapter 7: Extrusion Tooling / 489
The cooling of the removed tooling should 254 mm and a bore of 59 mm was located ap-
be carried out slowly in a suitable environment. proximately 150 mm from the front face. The
Stresses develop with incorrect heating and failure occurred after approximately 3800 ex-
cooling. From experience, there is the risk that trusions, because the stem had been loaded cold
in an environment that is too cold, thermal and was not preheated. The deformation tem-
stresses can develop in the tool that will result peratures for the indirect extrusion were in the
in fracture several days or weeks later. Thermal range of 750 to 900 ⬚C for different extruded
stresses in removed tooling are increased still materials with different extrusion programs.
further if the hot tool is subjected to the factory The temperature of the container liner was be-
air. Areas with air currents should definitely be tween 500 and 600 ⬚C.
avoided, because this prevents uniform cooling,
and cracks can easily develop. 7.5.5 Containers
At the end of a program or when a tool is The requirements for containers are a long
changed, it must be placed in a heated holding life, operational reliability, low maintenance,
station. Here, it is held at a temperature of 350 and rapid container changing, as well as low
to 400 ⬚C for 2 to 6 h, depending on the cross investment costs and high productivity.
section. A slow temperature decrease of ap- The size of the container can be immense
proximately 30 ⬚C (50 ⬚F) per hour is beneficial (Fig. 7.95). For a 125 MN extrusion press, an
to the tool and is an important requirement for external diameter of 2100 mm is necessary, and
a long life. Stems and mandrels should not be the length is 2000 mm, given a weight of 50
placed flat but heated or cooled in a standing tonnes for the container. The production is rela-
or hanging position. To avoid thermal shock, tively difficult, because of the size of the indi-
cooling by air or a mixture of air and water can vidual container components.
only be carried out during production. Heated Additional technological functions of the ex-
water should be used for the mandrel internal trusion tool container are becoming increas-
cooling. Overcooling should be avoided at all ingly important to improve the extrusion pro-
costs. The temperature drop from intensive cess. The temperature-controlled container,
cooling should not exceed 100 ⬚C. These con- with a combination of heating and cooling, is
siderations also apply to the temperature-related suited for the extrusion of aluminum alloys
operational maintenance and handling of con- with a constant exit temperature.
tainers. The fracture surface of an extrusion
stem (Fig. 7.94) with an external diameter of 7.5.5.1 Container Construction
There are different container constructions,
depending on the application of the container
(Fig. 7.96). The round billet is standard and, to The following suggestions and technical data
a certain extent, the prerequisite for extrusion. should be considered as guidelines for the de-
Solid or hollow billets can be used. The billet sign and construction of containers for extru-
with an oval cross section (rectangular billet) is sion.
the exception. It is used for aluminum alloys Standardization of extrusion tooling is based
with a high and moderate extrudability. The on many years’ practical experience with de-
necessary extrusion pressure in the container re- sign and manufacture in extrusion plants. The
quires a two-part or three-part design to with- most important technical data can be taken
stand the large stresses. The four-part design is from DIN 24540. This gives the main dimen-
required for extrusion pressures above 1250 N/ sions of the tooling for direct-extrusion presses
mm2 in the container. The stress-related dimen- from 5 to 125 MN. The container bores men-
sioning, including the shrink-fit, design, and tioned for rectangular billets require a specific
materials selection, is determined from stress design for the container as a whole.
analysis. In special cases and in the case of rec- Container internal pressure depends on the
tangular billet containers, the stresses must be extruded material. The values vary from a spe-
analyzed by FEM stress studies. The extruded cific extrusion pressure, FSt/A0, of 315 to 1000
material-dependent deformation temperature in- N/mm2. Higher values require special designs.
fluences the method of heating. Cooling is nec- Container internal bore is derived from the
essary in high temperature regions. The internal relative specific pressure needed to extrude the
components of the container in the center, in different materials and the size of the press. The
particular, are subjected to a buildup of heat. If range covers values of 80 to 710 mm diameter
temperature control of the container is neces- for round container bores for extrusion presses
sary for technological reasons, a controlled from 5 to 125 MN.
combination heating and cooling system that is Container length is not of fundamental im-
effective in different locations is necessary. The portance for the design and construction of the
wear on the free surface of the liner at high container. The container length must be re-
billet temperatures, combined with high extru- stricted because of the operational safety of the
sion pressures, must be taken into account in extrusion stem (risk of buckling). The relevant
materials selection. The spatial location of the data in DIN 24540 are values based on expe-
container must be stable in the press, indepen- rience. The container length is an important
dent of the working temperature. In other economic factor and is optimized for special
words, a central operation of the mandrel, stem, cases, for example, the standard extrusion of
dummy block, container, and die must be guar- aluminum alloys and indirect extrusion.
anteed for every operational state. A risk of ax- The two-part round billet container is used
ial movement of the liner can be prevented by for internal pressures up to 630 N/mm2. Con-
machining shoulders into the liner. tainer heating in the housing is sufficient for
Two-part container for round billets Three-part container for round billets Three-part container for round billets
materials that are extruded at temperatures be- In a combined heating and cooling system
low 500 ⬚C. This does not apply to products with temperature control, a localized tempera-
that require temperature control within the con- ture buildup can be prevented by cooling.
tainer. In the extrusion of seamless tubes, the The location and method of holding in the
cross section of the mandrel must be taken into tool holder (container holder) requires that there
account in the calculation of the internal pres- are no critical notches in the components. The
sure. central location of the container should be
Three-part round billet container designs are maintained independent of the actual working
required for internal pressures above 630 N/ temperature during the production period. Fast
mm2. As a rule, internal pressures over 630 N/ container changing times must be provided by
mm2 occur in tube extrusion. Internally cooled a quick connection. The heating and cooling
containers must be used for materials with ex- system also must be capable of being changed
trusion temperatures over 600 ⬚C. They should quickly.
be three-part even with internal pressures below Maintaining the interference fit is essential.
630 N/mm2 because of the higher stresses in If axial movement of the liner and sometimes
the area of the cooling grooves. the liner holder occur, then these must be fitted
The three-part rectangular billet container de- with a shoulder at the end against the direction
sign should be preferred to the two-part design, of slip. The shape of the shoulder must be de-
that is still found, to achieve a higher life. A signed so that stress concentrations from the
segmented internal liner is rarely used because notch effect are minimal.
of the high production costs. The liner with oval bore is usually one piece
Hot working requires a process-related tool and only rarely designed as segments.
temperature in the container. A specific tem- Containers for the Extrusion of Materials
perature is required, depending on the material in the Range of 0 to 300 ⬚C. Containers that
being extruded. Additional deformation and operate in this temperature range are only sub-
friction heat is produced during the extrusion jected to low thermal stresses. They are used
process. Heating and cooling systems, which for cold extrusion, the extrusion of lead and tin
can also be combined, are therefore necessary. alloys, and the extrusion of zinc alloys. In most
Containers for indirect extrusion differ from cases, the normal tools do not correspond to
those for direct extrusion only in the longer DIN 24540 because of their special designs,
container length. In addition, only three-part which meet the individual operational require-
round billet containers are used for indirect ex- ments.
trusion. The two-part design is rarely used be- In cold extrusion, specific extrusion pressures
cause of the cooling needed for temperature of approximately 1400 N/mm2 and higher are
control, even for the extrusion of aluminum. common. These pressures can only be with-
The design of the container is determined by stood by four-part containers. They are used
the production program in the extrusion plant. without heating, and the design length of the
This results in different constructions that only container is relatively short because of the ex-
permit a limited number of individual dimen- treme stem loading.
sions and features. The most important design Extrusion presses for the deformation of lead
considerations include the following. alloys operate with specific stem pressures
The hot-working material depends on the ex- above 160 N/mm2. Presses with 5 to 16 MN
truded material and the extrusion temperature. stem load are used for the production of lead
The heating system is usually installed in the tubes with a charge of 250 to 1800 kg. The
container mantle. Induction heating is used less containers are heated or cooled, depending on
frequently than resistance heating. The resis- the operational phase. The two-piece containers
tance heating can be divided into several heat- have a long length and are special designs that
ing zones. With rectangular billet containers, are sometimes fitted with steam heating and hot
heating elements are installed in the wide side, water cooling (80 ⬚C). Cable sheathing presses
the thick-wall part. Resistance heating is also for lead alloys operate with specific pressures
installed outside the container in the container between 325 and 550 N/mm2. The charge
holder. weights fall between 135 and 1000 kg. Cable
The cooling system is fitted on the external sheathing presses have press loads of 6 to 30
diameter of the liner holder within a three-part MN. The vertical operating presses are very
container. tall. The horizontal presses operate with two
492 / Extrusion, Second Edition
containers and two extrusion stems. Profiles, mm2. The shearing of the billet at the container
rod, and tubes in tin and lead alloys are pro- wall can be significantly more than 50% of the
duced for the chemical industry on presses with extrusion load needed, depending on the length
powers in the range of 5 MN. The containers of the billet. In direct extrusion, round and oc-
for solder wire extrusion have specific pressures casionally rectangular billets are used. In indi-
up to 630 N/mm2. They are small presses with rect extrusion, only round billet containers are
a maximum press power of approximately 2.5 used that are usually designed for long billets.
MN (see the section “Extrusion of Tin- and The round billet container is often designed
Lead-Base Soft Solders” in Chapter 5). without heating for the aluminum alloys with
The extrusion of zinc alloys requires specific high extrudability. In this case, the heating is
pressures of 800 to 1000 N/mm2 and tempera- located in the container housing in standard
tures of 200 to 350 ⬚C, depending on the ma- presses. The distance between the columns
terial. Smaller extrusion presses up to 10 MN must be sufficiently large for the removal and
press power are used. Because these extruded replacing of a container. The dimensions of the
products in the form of tube, section, and wire press cross section are therefore determined by
have a limited application, only a few presses the external diameter of the container. The ad-
are in operation. The containers for the zinc al- vantage of round billet containers without heat-
loys can be designed according to DIN 24540. ing is obviously the smaller external diameter.
Containers for the Extrusion of Materials Consequently, the investment costs for the con-
with Deformation Temperatures of 300 to tainer and for the standard extrusion press,
600 ⬚C. This family of containers, which is al- which can be more compact, are significantly
most exclusively used for the extrusion of mag- lower. Round billet containers with heating are
nesium and aluminum alloys, is found in over always needed if higher technological require-
70% of all extrusion plants. The tooling and the ments are placed on the extrusion process. In
containers basically correspond to the standard the extrusion of aluminum alloys with moderate
DIN 24540. Large extrusion presses from 80 to and low extrudability, the heating is preferably
200 MN press power are only found in alumi- located as resistance heating in the container
num extrusion plants. Conventional hot work- mantle. Temperature-controlled containers that
ing steels can cope with the thermal stressing include combined heating and cooling systems
of the container that results from the deforma- are well suited for the extrusion process. These
tion temperature. While deformation tempera- are particularly important for the quality of the
tures of 250 to 450 ⬚C and pressures up to 400 product in indirect extrusion. Rectangular billet
N/mm2 are necessary in the extrusion of mag- containers are also fitted with resistance heating
nesium alloys, the deformation temperatures in (Fig. 7.97).
the extrusion of aluminum alloys are between However, recent developments have replaced
350 and 530 ⬚C. The deformation pressures re- the expensive rectangular billet container with
quire specific press pressures up to 1000 N/ spreader feeder chambers for round billet con-
Single part liner Segmented liner, four part Liner with two segments
Fig. 7.97 Rectangular billet containers with different segment arrangements for the liner. Source: Groos
Chapter 7: Extrusion Tooling / 493
tainers. These so-called spreaders enable flat must be equipped with a combined heating and
profiles to be produced from round billet con- cooling system, because of the long billet and
tainers that have widths close to those from rec- the rapid billet throughput. The round billet
tangular billet containers, as described in the containers must be three-part designs. If the
section about spreader chambers in this Chap- liner is made from high hot strength austenitic
ter. The widely used single-piece liner with a tool steel, it must have a thin wall because of
rectangular bore has a very limited life. This the poor thermal conductivity and the higher
design should not be used with extrusion pres- thermal expansion. If only tubes are extruded,
sures over 560 N/mm2. The dimensions given then short, round billet containers can be used.
in DIN 24540 part 2 correspond to this design. In this case, the rod and tube press can operate
The four-part segmented design was developed with a correspondingly shorter stroke.
by the Loewy Construction Company in the The thermomechanical stressing of the con-
United States in 1954. It also gives an accept- tainer family described here has always been a
able service life at higher extrusion pressures. problem that demanded a solution. The liner is
However, this expensive design is associated heated above the limit of the tool material by
with high production costs. The extent to which the high billet temperatures. The maximum
two segment liners, a design from Edelstahl- tempering temperature of the liner material is
werke Buderus AG for an extrusion plant in the exceeded, leading to a rapid loss in strength.
United States, has proved successful is not The extrusion loads then result in plastic defor-
known. Apart from the difficulties associated mation. The shrink-fit then disappears and loses
with securing the two segments, it is a solution its function. Cooling of the liner wall between
that is economic from the production costs and cycles with a reduced press output and frequent
appears practical from the technical point of turning of the container, that is, moving the
view. stem face to the die face, can no longer be ac-
Containers for the Extrusion of Materials cepted because of the poor productivity. The
with Deformation Temperatures from 600 life of the container is unsatisfactory in spite of
to 1300 ⬚C. Only round billets are used for these measures. A technically and economically
containers in this temperature range for direct usable design to avoid overheating of thermally
and indirect extrusion. The dimensions of the highly stressed round billet containers is the in-
containers correspond to the standard DIN tegrated heating and cooling system. This ap-
24540 for extrusion tooling. Rod and tube ex- plies to the extrusion of materials with high de-
trusion presses for copper alloys have press formation temperatures, which includes copper
powers between 5 and 80 MN. Extrusion alloys. The internal cooling does result in a
presses for the production of brass products, in- weakening of the contact faces of the interfer-
cluding wire and bar, are often indirect presses. ence-fit liner holder/mantle. The surface of the
Containers for deformation temperatures over outside diameter of the liner holder is reduced
600 ⬚C without a suitable temperature control by the cooling channels. This should not have
to prevent overheating cannot be justified today an unacceptable effect on the interference fit.
and are also uneconomic. If the container can Even so, the cooling grooves (Fig. 7.98) on the
be cooled, particularly with rapid billet outside diameter of the liner holder naturally act
throughputs, and if the liner is made from an as stress concentrations. Cooling and interfer-
age-hardening austenitic tool steel similar to ence surfaces must be balanced in the design of
1.2779 with a high hot strength, then high billet the container together with minimization of the
temperatures can be accommodated. Whereas, notch effect.
for the extrusion of copper-zinc alloys, tem- Titanium alloys are lubricated with glass,
peratures of 650 to 750 ⬚C and pressures up to similar to iron alloys. The billet friction is
800 N/mm2 are required, the extrusion tem- therefore low. The glass film reduces the heat
peratures for copper alloys are between 800 and transfer from the extruded material to the tool-
900 ⬚C. The pressures can reach 1000 N/mm2. ing. For the extrusion of iron alloys and nickel
Because extrusion is normally carried out with alloys, only round billets for direct extrusion
a shell, billet shearing of the copper alloy oc- are used. Tube production dominates. The di-
curs close to the container liner wall. This re- mensions of the container largely follow the
quires 10% of the extrusion load. Indirect ex- standard for extrusion tooling, DIN 24540. Rod
trusion of copper alloys is mainly restricted to and tube presses in the size range of 16 to 110
copper-zinc alloys. In this case, the container MN are mainly used. The thermal stressing of
494 / Extrusion, Second Edition
Fig. 7.98 (a) Combination heating and cooling system. Source: Groos. (b) Liner holder with cooling grooves. Source: Böhler
Chapter 7: Extrusion Tooling / 495
the containers at deformation temperatures over ● Interference forces on the container com-
1000 ⬚C requires special measures to achieve ponents, that is, the compressive stresses on
an acceptable life. High extrusion speeds are the liner and liner holder and the tensile
usually used in the high-temperature range. The stresses on the mantle
contact time with the tooling by the hot ex-
truded material is then short. In addition, the The analysis of the mechanical stresses on
insulating effect of the glass lubricant in the the container should also consider the container
container helps prevent overheating of the die, sealing forces and the friction and shear forces
liner, and dummy block. The billet friction is that develop during extrusion. These forces,
very low. The method of lubrication, whether which should not be underestimated, act in the
with glass or, more rarely, an oil-graphite salt axial direction. The resultant three-axis stress
mixture, has little effect on the magnitude of state must be taken into account.
the billet friction. The specific extrusion pres- The thermal stresses result in more complex
sures required are often in the range of 1000 N/ problems. They arise from:
mm2. Integrated cooling in the container is not ● Local overheating
used. Thin-wall liners, which have a limited life ● High billet throughputs with billet tempera-
as a wear component, are used successfully. tures over 600 ⬚C
They are not shrink-fitted in the conventional ● Short billets with billet temperatures over
way and can be quickly changed. They protect 600 ⬚C
the containers from excessive temperature. ● Too rapid heating and cooling when chang-
ing containers
7.5.5.2 Thermomechanical Stressing of The thermal stresses can be withstood if, dur-
the Container during Extrusion ing production:
The thermomechanical stressing during press ● A maximum temperature well below the
operation results in an extremely complex set tempering temperature of the hot working
of circumstances in the container that is char- steels used for manufacture can be held at
acterized by considerable interactions. The all locations within the container.
magnitude of the thermal and mechanical ● A reliable heating and cooling system
stresses in the container is often at the upper within the container is available for tem-
limit of conventional hot working materials. perature control that can demonstrably
This results in a limited life for the liner and maintain the specified working temperature
ultimately for the container. without an unacceptable buildup of heat in
The mechanical stressing of the container is the central area of the container.
best illustrated using: ● Only a preheated container is used when the
● Containers with round bores tooling is changed, and the removed con-
● Containers for the extrusion of materials tainer is cooled slowly under a thermal pro-
that require an extrusion pressure below tection cover.
1000 N/mm2 Unacceptable thermal conditions occur:
● Containers free from dangerous notches in
their design and manufacture. The stresses ● When, during production, materials with ex-
that can result from unavoidable heater trusion temperatures over 600 ⬚C are ex-
holes, shoulders, and slots must be held truded without a heating and cooling sys-
within acceptable limits because of stress tem, that is, without a reliably operating
concentrations. thermal control, in this case, without cool-
ing
The mechanical stresses result from: ● When the resultant temperature exposure re-
sults in an unacceptable heat buildup in the
● Specific pressure during extrusion central region of the container
● Externally applied sealing force from the ● When there is excessive cooling of the con-
container movement that corresponds to the tainer from the outside
contact force between the container and the
die or the die holder In the extrusion of materials with deforma-
● Friction and shearing between the billet and tion temperatures over 600 ⬚C, there exists an
the liner wall extremely unequal temperature distribution
496 / Extrusion, Second Edition
zones to give localized heating. However, the tance heating is also the most suited for an ef-
exposed heating wire oxidized and was suscep- fective temperature control. An almost constant
tible to damage in the harsh working condi- temperature or a predetermined temperature
tions. This resulted in the development of heat- profile over the container length can be
ing elements that encapsulated the heating wire achieved with a combination of resistance heat-
and thus protected it from oxidation and me- ing with integrated cooling.
chanical effects. These are referred to as tubular The smaller the gap between the cartridge di-
elements and heating cartridges. ameter and the bore, the higher the heat transfer
The tubular heating elements have a rela- efficiency. The division of a container into six
tively small external diameter. The thin heating controlled zones, as shown in Fig. 7.101, by the
wire in Cr-Ni-Fe is embedded in magnesium use of a combined heating and cooling system
oxide in an airtight alloy steel tube. Heating is advantageous. The location of three thermo-
elements with tube diameters of 8 mm are fitted couples—in the upper region on the die side, in
to the container housing. Heating elements with the center, and on the stem side—and three ad-
tube diameters of 12 mm are fitted as plug-in ditional opposing thermocouples in the lower
elements in heating holes of 42 mm in the con- region, each measuring on the external diameter
tainer mantle. With the large clearance between of the liner, provides good monitoring of the
the tubular heating elements and the heater hole container. Each heating zone has a temperature
in the container, the surface temperature of the probe. To protect against overheating of the
heating elements must be very high, up to 800 heating cartridges, an additional thermocouple
⬚C. Increasingly, therefore, heating cartridges is often installed close to a heating cartridge in
are being used for container heating. Macro- the central region. The heating connection must
tubes (heating cartridges) can be considered as be designed for both the die side and the stem
larger tubular heating elements. They are fitted side. The time needed to disconnect and recon-
with a thicker heater wire and have an outside nect the measuring and heating cables to the
diameter of 31.5 mm within narrow tolerances container is relatively short when changing the
[Eck 97]. tooling, compared to induction heating (Fig.
The efficiency of resistance heating is deter- 7.102).
mined by the efficiency of the heat transfer. Locating a resistance heating system in the
Heating cartridges located directly in the con- container housing is less effective but is suffi-
tainer are the best for thermal balance. Resis- cient in specific applications (Fig. 7.103). Be-
Fig. 7.101 Schematic arrangement of six-zone resistance heating in a container. Source: Groos
Chapter 7: Extrusion Tooling / 499
Fig. 7.102 Four-zone heating with quick heating connection. Source: Marx
Fig. 7.103 Schematic arrangement of four-zone resistance in the container housing. Source: Groos
cause no heater holes are required in the con- ple. Before a new container is loaded, it should
tainer mantle, the external diameter of the be preheated to the working temperature in a
container is smaller than with a container with special heating station. For prolonged downtime,
integrated heating. The container is therefore less a transportable additional resistance heater for
expensive. Container changing without heating the liner bore is useful. However, temperature
connections requires less time. The replacement control of the container by resistance heating in
of defective heating elements is relatively sim- the container housing is not possible.
500 / Extrusion, Second Edition
tainer end faces. The inevitable heat buildup in with air has proved to be best suited for con-
the middle of the container can be reduced by tainers. The necessary cooling intensity requires
internal container cooling. A specified tempera- compressed air. Working with compressed air
ture profile similar to that with resistance heat- in the plant is simple, environmentally friendly,
ing cannot be achieved with induction heating and safe. The cooling intensity of the com-
and integrated cooling. pressed air can be varied by the pressure. It can
be precisely fed locally into the hotter zones,
7.6.1 Combined Container which is advantageous for the different tem-
Heating and Cooling System peratures in the container. The hot exhaust air
is taken away so that there is no detrimental
An understanding of the temperature distri- effect on the surroundings. Cooling with com-
bution in the different zones of the container is pressed air is suitable, because the tool material
essential for the design and control of an effec- being cooled is protected. Figure 7.98 shows
tive combination heating and cooling system. the cooling grooves of a liner holder and the
The temperature fields in the container must be cooling in a container.
maintained constant, and overheating in the The combination of resistance heating and
center must be excluded. The use of cooling compressed air cooling is now the best-suited
cannot be avoided. The combined heating and technology for a temperature-controlled con-
cooling systems (Fig. 7.98) are very important tainer. The resistance heating must be divided
for the economics and product quality in the into several zones, and the cooling must be lo-
extrusion plant and should therefore be stan- cally adjustable. It must be possible to vary and
dard. alternate the supply and exhaust of the cooling
A constant temperature over the container compressed air over the container length. At
length can only be achieved to a limited extent, least six thermocouples in suitable locations in
because of the exposed container end faces. the container are required for the monitoring
There is no suitable thermal insulation available and control of a combined heating and cooling
for the container end faces. Heat buildup within system. If aluminum alloys are extruded, it is
the container can be partly reduced by dividing economic to operate with an individual tem-
the heating into zones. An effective method of perature profile matched to the particular de-
countering the buildup of heat in the middle formation conditions. The heating and cooling
region of the container is the cooling of the hot- systems described have proved successful in
ter zones. practical operation. They are of fundamental
In hot working, there is a wide range of importance for the further development of the
methods used for cooling the tooling. Of the process technology. The temperature losses in
most common cooling media, including water, the area of the container end faces are low and
cooling oil, air-water mixture, and air, cooling can be ignored in practice. They only influence
502 / Extrusion, Second Edition
the extrusion process over a length of 100 to depends on the number of extrusion cycles per
150 mm from the end face, depending on the unit time. If, however, only slow stem speeds
size of the press. are possible for the deformation of an extruded
Compressed air cooling is also advantageous material, as, for example, with the aluminum
for containers heated by induction. In the ex- alloys with low extrudability, the dynamic load-
trusion of copper alloys, the combination of in- ing of the container can be considered to be
duction heating and compressed air cooling is cyclic creep loading. Hot working steels that
necessary. The service life of the container liner are subjected to creep loading can be subjected
can be significantly improved by reducing the to plastic deformation if the creep strength is
heat buildup in the central region of the con- exceeded, which is referred to as material creep.
tainer, using compressed air. This reduces tool- Both the optimal design of a container and
ing costs significantly, and thus, downtime for the use of the correct hot working tool steels
container changing occurs less often. Three are important. Container mantles manufactured
thermocouples located at suitable positions in in the hot working steels 1.2323 and 1.2714
the container are used for the monitoring and exhibit significant strength losses, apparently
control of the induction heating and cooling caused by production-related long-term temper-
system. Containers for copper extrusion with ing under thermal stresses. Incorrect preheating
induction heating can be retrofitted with com- with excessive temperature gradients in the
pressed air cooling. Retrofitting of compressed container mantle can also contribute to this. As
air cooling for aluminum extrusion is less ben- a result of the loss in strength, the container
eficial. It cannot guarantee the desired tempera- mantles can no longer elastically withstand the
ture control with induction-heated containers. forces developed during the extrusion process.
The problem was solved by the use of the more
temper-resistant hot working steel 1.2343 in-
stead of the previously used less temper-resis-
7.7 Design, Calculation, and tant hot working steels.
Dimensioning of Containers The container design should be as simple as
possible, with extensive avoidance of design
The standard multipart container is subjected details that produce stress concentrations.
to three-dimensional variable and superimposed Notch-induced stress concentrations in the con-
forces during the extrusion cycle. Basically, tainer mantle region can result in a fatigue fail-
these are: ure. Notch-acting areas cannot always be com-
● Radial and tangential deformation stresses pletely avoided in container design. Points to
during extrusion consider are:
● Axial tangential and shear forces during the ● Heating and thermocouple holes in the man-
direct-extrusion process tle and the liner holder
● Radial, tangential, and axial residual ● Keyways in the mantle to hold and locate
stresses produced by the shrink-fitting pro- the container
cess ● Blends at the cylindrical shoulders on the
● Axial sealing forces between the container liner, liner holder, and/or mantle
and the die in direct extrusion ● Cooling grooves in the liner holder mantle
● Axial container moving force in the extru- face
sion direction in indirect extrusion
Consideration should also be given to the
The deformation forces shown in Fig. 7.105 fact that coarse machining marks on the mating
stress the container between 0 and the maxi- surfaces of the container components and the
mum stem load, FSt max. The shrink-fitting surface of the container mantle can result in
stresses in the container are superimposed on high stress concentrations. Unacceptably high
the deformation loads. As a result of the super- stress peaks should be avoided. In addition, the
imposition, the liner of a two-part and the liner shape and positional tolerances according to
and the liner holder of a three-piece container DIN 7184 must be maintained in terms of
are dynamically loaded in the tension/compres- straightness, angularity, concentricity/coaxial-
sion range, whereas the container mantle is al- ity, and runout. This applies to the mating sur-
ways subjected to dynamic fluctuating tensile faces of the individual container components
loads. The frequency of the dynamic stressing and, equally, for the alignment accuracy of the
Chapter 7: Extrusion Tooling / 503
Two-part container
Mantle
Interface joint: mantle/liner
Liner
Upset billet
Extruded section
Direction of extrusion
Die
Discard
Dummy block
I
B IB = Initial billet length
I
0 I0 = Upset billet length
F
St Load displacement diagram
F FSt = Stem force
An
FM = Deformation force
Direct
F FR = Friction and shear force
R
FAn = Force at the start of extrusion
SS = Upset displacement
SP = Extrusion displacement
F Indirect
M SR = Discard
S
0 st
S S S
S P R
Stress diagram
Axial interference forces
(Condition with a new container)
Variation in the tensile stresses in the mantle
0
Maximum tensile stress at the end faces
Variation of the compressive stresses in the liner
Maximum compressive stresses in the middle section
extrusion tooling within the extrusion press, ing system must be integrated into the con-
where the container plays a decisive role. For tainer.
rapid installation and removal of the container, After the operating program has been estab-
the container housing is fitted with a quick-fit lished, the estimates of the maximum extrusion
connection that is also suitable for the position- pressure and the maximum thermal stresses are
ing and transfer of the container sealing forces. the important factors in the initial design of the
Very demanding design analysis is required container. Tables 7.7 and 7.8 give correspond-
when a heating or combined heating and cool- ing material-dependent data for containers with
504 / Extrusion, Second Edition
and without cooling. The container can be pro- 2 Estimate the maximum extrusion pressure
visionally designed using these stress parame- and the maximum temperature
ters. Table 7.18 in section 7.17 helps to select 3 Preliminary design of the container, based on
the material for the container as a function of values from experience or assumptions for a
the material being extruded. The final analysis new design with preliminary determination
of the container—usually following the classic of the dimensions and material of the con-
elastic theory—follows the optimization of the tainer
initial dimensions. The analytical results enable 4 Accurate calculation of the container, with
corrections to be made to avoid excessive subsequent optimization of the preliminary
stresses. A fatigue life calculation using the ex- container design using the results
pected load collective of the container, which 5 Estimate the fatigue life of the new container
must be obtained from the actual thermal and using the load collective from the operational
mechanical stresses over a long period of time program
on a similar container, is the final stage of the
design process. The subsequent operational A container is not continuously thermome-
steps are followed for the design of a new con- chanically stressed to its maximum. More often,
tainer as well as a new development in the con- the extrusion load required varies according to
text of DIN 24540: the production requirements, between 65 and
90% of the maximum load of the extrusion
1 Determine the extrusion program as the start- press. The thermal stressing also depends on the
ing point relation between the time needed for the actual
Chapter 7: Extrusion Tooling / 505
deformation and the total time of the extrusion case of the round billet container as well as
process. Some information is given in Table around the asymmetrical liner in the rectangular
7.9. The pure extrusion times given in the table, billet container (oval cross section). Stress con-
which vary significantly depending on the ma- centrations and thus crack-susceptible areas can
terial being extruded, also demonstrate that it is be avoided by design measures, including, for
not advisable to universally use containers for example, fillets on keyways, increased distance
mixed-extrusion programs, which has occasion- between holes in groups of holes, and overall
ally occurred in the past. For example, if alu- notch-free design. The FEM studies enable op-
minum alloys and copper alloys were extruded timal designs for the manufacture of containers
from the same container, which would result in to be realized.
quality problems, these containers would al- For a long time, little importance was at-
ways have to be designed for the maximum tached to the axial stresses. Experience has
thermomechanical stresses. They would then be shown that the axial forces on the container
expensive and uneconomic. should not be completely ignored. The follow-
It is important to adhere to the design- and ing axial forces can act on the container:
manufacture-related operating conditions as
● Friction and shear forces on the liner wall
well as the safety considerations to ensure the
extended operational availability of a container. during direct extrusion
● Axial forces developed during the shrink-
For safety reasons, the following exceptional
operating conditions must be avoided: fitting of the container components
● Container moving force involved in indirect
● Heat buildup extrusion, resulting from the displacement
● Sticking billets in the container, that is, in- force in the extrusion direction
sufficient maximum press load to extrude ● Container sealing force against the die and/
the billet or die holder in direct extrusion
● Overloading in the hydraulic system, result-
ing from incorrect setting or safety valves The friction and shear forces operating in di-
● Overloading as a result of unacceptably rect extrusion can be obtained from a plot of
high extrusion pressures by the use of man- the extrusion load against the ram displace-
drels with excessive cross sections in tube ment, as seen in Fig. 7.105.
extrusion In the direct extrusion of aluminum alloys,
● Excessive temperature gradients during the magnitude of the friction and shear forces
heating or cooling of containers is between 30 and 60% of the maximum force,
● Misalignment between the extrusion tooling FSt max, and in the direct extrusion of copper
alloys, 5 to 30%. At the start of the deformation
The FEM analysis in Fig. 7.106 shows the of the billet, these forces are at a maximum,
variation in the equivalent stresses, rv, in the and the axial loads on the container are par-
components of two three-part containers, with ticularly high during this phase of the extrusion
the high stresses around the heater holes in the process. However, they continually decrease
FR ⳱ 0.3 ⳯ 25 ⳱ 7.5 MN
partly undergoes plastic deformation during the stressed, the function of the original interfer-
extrusion process. This changes the prestress ence stresses is reduced.
state produced by the shrink-fitting in the con- To summarize, the analysis of the axial loads
tainer. At the same time, the liner is again sub- on the container reveals a varied stress situa-
jected to compressive stresses, because it wants tion. The axial forces have very different orders
to expand under the high thermomechanical of magnitude, depending on the deformation
stresses, but this is prevented by the interfer- conditions for the extruded material under con-
ence fit. The mantle is only slightly loaded by sideration, and cannot be fully determined. It is
tensile stresses from the interference fit because recommended that the axial forces developed
of the significantly larger volume. by interference stresses acting on the container,
The axial forces developed in the container the friction/shear forces, and the container seal-
during cooling after shrink-fitting can only be ing forces be taken into account, with the help
approximately determined. With hot working of Table 7.10.
steels with equal coefficients of thermal expan- From this, the axial loading of the container
sion, the axial length change, for example, of in a direct-extrusion press for the extrusion of
the liner relative to the mandrel is in the range copper alloys is given by the axial stress:
of 0.01 to 0.04% depending on the shrinkage
forces and the length of the container. The re-
rz ⳱ 0.35 ⳯ pi Ⳮ 0.35 ⳯ ps
sultant axial stresses are superimposed on the
radial and tangential stresses in the liner in the
static and working conditions. Over time, the These values are reasonably close enough to re-
original prestresses in the container from the ality for the determination of the equivalent
shrink-fitting can change radially and axially stresses in the container, as shown by the cal-
because of temperature differences between the culation examples in section 7.10.
container components as a result of heating and The manufacturers of containers have con-
cooling as well as the fluctuating working con- siderably improved and standardized the clas-
ditions. According to these considerations as sical methods of calculation. Today, multipart
well as practical experience, the interference fit containers can be analyzed in minutes by using
is lost when: computer programs using classical elasticity
theory from the specified data. There have also
● The operating temperature exceeds 600 ⬚C, been many efforts to mathematically determine
that is, over the tempering temperature of the elastic/plastic behavior of containers and
the hot working steels used. their components subjected to high thermome-
● The container mantle under the applied con- chanical stresses. However, practical experience
tainer sealing load is heated too quickly, that has shown that the method of classical elasticity
is, with an excessive temperature gradient. theory using the safety factors k in the section
● Significantly hotter billets are extruded in a “Static- and Elastic-Based Analysis and Dimen-
cold container. sioning of Containers Loaded in Three Dimen-
sions” in this Chapter usually suffices for the
A billet heated to the extrusion temperature design of containers not subjected to extremely
and upset in a container that is too cold raises high thermomechanical stresses. However, the
the temperature of the liner, which then wants elastic equilibrium conditions derived from the
to expand according to the temperature but is equilibrium analysis in the aforementioned sec-
prevented by the container mantle or the liner tion in the form of integral equations can only
holder. If it is then thermomechanically over- be fully integrated with simplified assumptions.
Table 7.10 Reference values for determining the axial forces on the container during extrusion
Effective axial forces Factors
Application Prestresses, ps Working stresses, pi ps pi
Indirect-extrusion copper alloys Interference-fit forces ... 0.5 ...
Indirect-extrusion aluminum alloys Interference-fit forces ... 0.5 ...
Direct-extrusion copper alloys Interference-fit forces Friction/shear forces, container sealing forces 0.35 0.35
Direct-extrusion aluminum alloys Interference-fit forces Friction/shear forces, container sealing forces 0.35 0.65
Source: Groos
508 / Extrusion, Second Edition
Table 7.11 Characteristic material parameters of hot working tool steels and a nickel-base hot
working material measured at room temperature (RT) and at 500 ⬚C under static and dynamic
loading
Tool steel number Abbreviation Rm/RT, N/mm2 Rm/600, N/mm2 Rp0.2/500, N/mm2 RZSch/500, N/mm2 A5, %
1.2343 X38CrMoV51 1511 1040 883 540 12
1.2344 X40CrMoV52 1619 1099 706 530 12
1.2365 X32CrMoV33 1354 883 638 441 8
1.2567 X30WCrV53 1511 1014 706 510 12
1.2581 X30WCrV93 1550 1099 903 530 8
1.2603 45CrMoW58 1452 952 706 481 12
1.4973 NiCr19CoMo 1315 1295 952 598 ...
Rm/RT, tensile strength at room temperature; Rm/500, tensile strength at 500 ⬚C; Rp0.2/500, 0.2% proof stress at 500 ⬚C; RZSch/500, elevated-temperature tensile fatigue
strength. Source: [Wan 72]
Container outer wall: pressure FSt/A0, radially load the container with
the working pressure, pt. The resultant opera-
1 tional stresses, rr and ry, must to be obtained
rv(ra) ⳱ from the one-part container analysis. Accord-
冪2
ingly:
冪(rt(ra) ⳮ rr(ra))2 Ⳮ (rr(ra) ⳮ rz)2 Ⳮ (rz ⳮ rt(ra))2
For the liner wall of the container
The maximum equivalent stress always occurs
on the container inner wall. u2 Ⳮ 1
r (d1i) ⳱ ⳮpi
rxx t (d1i) ⳱ pi
rxx
u2 ⳮ 1
7.9 Design of a Two-Part Container For the interface d1a/d3i of the two-part con-
tainer:
7.9.1 Calculation of the Prestresses rxr
ⳮ1 Ⳮ1
冢dd 冣 ⳱ ⳮp uu 冢dd 冣 ⳱ p uu
2 2
1a 3 1a 3
and rxt Developed in a Two-Part rrxx i rtxx
ⳮ1
i
3i
2
3i
2
ⳮ1
Container by the
Interference-Fit Forces For the container outer wall:
The interference pressure, ps, between the
liner and the mantle is obtained from: 2
r (d3a) ⳱ 0
rxx t (d3a) ⳱ pi
rxx
u ⳮ1
2
E ⳯ es (u2 ⳮ 1) ⳯ (u12 ⳮ 1)
ps ⳱ ⳯ 3 The effective stresses in the container (the
2 u2 ⳮ 1
working stresses) are obtained from the addi-
The prestresses produced from the interfer- tion of the operational stresses and the pres-
ence pressure, ps, are calculated from: tresses (additive superimposition).
in a Two-Part Container
For the interface on the liner outer wall:
Accordingly:
u2 Ⳮ 1
rrx(d1a) ⳱ ⳮps rxt (d1a) ⳱ ⳮps 21 For the container inner wall:
u1 ⳮ 1
r (d1i) ⳱ ⳮpi
rxxx
For the interface on the mantle inner wall:
u2 Ⳮ 1 2u2
rtxxx(d1i) ⳱ pi ⳮ ps 2 1
u23 Ⳮ 1 u ⳮ1
2
u1 ⳮ 1
rrx(d3i) ⳱ ⳮps rtx(d3i) ⳱ ps
u23 ⳮ 1
For the outer wall of the liner at the interface:
For the mantle external wall: u23 ⳮ 1
r (d1a) ⳱ ⳮpi
rxxx ⳮ ps
u2 ⳮ 1
2
rxr (d3a) ⳱ 0 rtx(d3a) ⳱ ps u23 Ⳮ 1 u2 Ⳮ 1
u23 ⳮ 1 t (d1a) ⳱ pi 2
rxxx ⳮ ps 12
u ⳮ1 u1 ⳮ 1
7.9.1.1 Calculation of the Working For the mantle inner wall at the interface:
Stresses rxx xx
r and rt from the
Extrusion Forces in a u23 ⳮ 1
Two-Part Container r (d3i) ⳱ ⳮpi
rxxx ⳮ ps
u2 ⳮ 1
During extrusion, the deformation forces in u Ⳮ1
2
u2 Ⳮ 1
rtxxx(d3i) ⳱ pi 32 Ⳮ ps 32
the container bore, or rather the specific stem u ⳮ1 u3 ⳮ 1
Chapter 7: Extrusion Tooling / 511
冢dd 冣 ⳱ ⳮp u ⳯u ⳮu ⳮ1 1
rv(d1a) ⳱ 2a
2
3
rxr s1 2 2
1 3i 3 2
冪(rt(d1a) ⳮ rr(d1a))2 Ⳮ (rz ⳮ rt(d1a))2 Ⳮ (rz ⳮ rr(d1a))2
冪2 u Ⳮ 1
r冢 冣 ⳱ p
2
xd 2a 3
t s1
d 3i u ⳯ u ⳮ1 2
3
2
2
For the inner wall of the mantle at the interface:
For the outside wall of the mantle:
rv(d3i) ⳱
1 2
冪(rt(d3i) ⳮ rr(d3i))2 Ⳮ (rz ⳮ rt(d3i))2 Ⳮ (rz ⳮ rr(d3i))2 rxr (d3a) ⳱ 0 rxt (d3a) ⳱ ps1
冪2 u23 ⳯ u22 ⳮ 1
For the external wall of the mantle: Under the effect of the interference pressure,
ps2, the following radial and tangential pres-
rv(d3a) ⳱ tresses, r0r and r0t , occur in the container if the
1
liner and liner holder are treated as one item:
冪(rt(d3a) ⳮ rr(d3a))2 Ⳮ (rz ⳮ rt(d3a))2 Ⳮ (rz ⳮ rr(d3a))2
冪2 For the liner wall:
2 u2 Ⳮ 1
r0r (d3i) ⳱ ⳮps2 r0t (d3i) ⳱ ⳮps2 r (d1i) ⳱ ⳮpi
rxxx rtxxx(d1i) ⳱ pi
u3 ⳮ 1
2
u2 ⳮ 1
2
2u1 2 ⳯ u22 ⳯ u21
For the outside wall of the mantle: ⳮ ps1 ⳮ ps2 2
u1 ⳮ 1
2
u2 ⳯ u212 ⳮ 1
2
r0r (d3a) ⳱ 0 rt0(d3a) ⳱ ps2 For the interface 1 outside of the liner:
u23 ⳮ 1
r (d3a) ⳱ 0
rxxx 7.10 Examples of Calculations for
Different Containers, Their
2 2
t (d3a) ⳱ pi
rxxx Ⳮ ps1 2 Stresses and Dimensions
u2 ⳮ 1 u3 ⳯ u22 ⳮ 1
2 Examples of the stresses and dimensioning
Ⳮ ps2 of containers are given in this section. The two-
u32 ⳮ 1
part container described in section 7.10.1 is not
very highly stressed in terms of the relatively
7.9.2.4 Calculation of the Equivalent
low thermal and mechanical loads. The stresses
Stresses, rv, in the fall in the elastic range of the hot working
Three-Part Container steels. In section 7.10.2, a comparable liner
For the inside wall of the container (liner with a round bore is selected for the liner with
bore): an oval bore. Stress concentrations for a life
estimate must be determined by FEM analysis.
rv(d1i) ⳱ In section 7.10.3, the calculated stresses in a
three-part container for copper alloys is de-
1
冪(rt(d1i) ⳮ rr(d1i))2 Ⳮ (rz ⳮ rt(d1i))2 Ⳮ (rz ⳮ rr(d1i))2 scribed. The results show that the mechanical
冪2 loading at high working temperatures necessi-
tates further investigations for service life, par-
For the outside wall of the liner at the interface: ticularly of the liner.
The influence of the axial load is clearly
rv(d1a) ⳱ shown in the comparison in section 7.10.4. The
1 working condition that arises from the plastic
冪(rt(d1a) ⳮ rr(d1a))2 Ⳮ (rz ⳮ rt(d1a))2 Ⳮ (rz ⳮ rr(d1a))2 behavior of the material at the high tempera-
冪2
tures of the container components is discussed
in section 7.10.5.
For the inner wall of the liner holder at the in- The working conditions in hot working by
terface: extrusion vary considerably. Therefore, a de-
tailed knowledge of the working parameters in
rv(d2i) ⳱ a particular application is necessary for the de-
1 sign of a container. Basically, the maximum
冪(rt(d2i) ⳮ rr(d2i))2 Ⳮ (rz ⳮ rt(d2i))2 Ⳮ (rz ⳮ rr(d2i))2 possible thermal and mechanical loads that can
冪2
occur during production provide the starting
For the outer wall of the liner holder at the in- point. Load records are therefore required. At
terface: working temperatures of 600 ⬚C and above, the
elastic limit of hot working steels is greatly ex-
ceeded. In this case, consideration must be
rv(d2a) ⳱
given to the measures (cooling, special hot
1 working steels) that will reduce material dam-
冪(rt(d2a) ⳮ rr(d2a))2 Ⳮ (rz ⳮ rt(d2a))2 Ⳮ (rz ⳮ rr(d2a))2
冪2 age and thus increase the service life.
The calculated stresses are necessary to de-
For the inside wall of the mantle at the inter- termine the life of a container.
face:
7.10.1 Design of a Two-Part
rv(d3i) ⳱ Container with a Round
1
Bore for Aluminum Alloys
冪(rt(d3i) ⳮ rr(d3i))2 Ⳮ (rz ⳮ rt(d3i))2 Ⳮ (rz ⳮ rr(d3i))2
冪2 Two-part containers are usually used for the
easy and moderately difficult-to-extrude alu-
For the outside wall of the mantle: minum alloys. In this example, the formulae for
calculating the stresses are taken from section
rv(d3a) ⳱
7.9. The data for the calculation and the equiv-
alent stresses, rv, for dimensioning the con-
1 tainer and the selection of the hot working steel
冪(rt(d3a) ⳮ rr(d3a))2 Ⳮ (rz ⳮ rt(d3a))2 Ⳮ (rz ⳮ rr(d3a))2
冪2 are given as follows.
514 / Extrusion, Second Edition
cantly reduced by the axial stresses. Table 7.12 can occur. If embrittlement and ultimately fa-
shows the result of the calculation. tigue of the material, together with a reduction
Although the prediction of the developed in the ductility, occur as a result of further high
stresses includes relatively coarse simplifica- thermal and mechanical loading, then the con-
tions and thus induces uncertainties into the cal- sequence is the formation of a crack.
culation, axial forces should always be taken While the static stressing process damages
into account if the thermal and mechanical the hot working material by creep, fatigue re-
working stresses reach the limits of the hot- sults from the number of load cycles. The creep
working steels. and the fatigue damage results in permanent de-
formation and a reduction in the service life of
7.10.5 Operating Conditions from the container [Ber 76/1-4].
Elastic/Plastic Behavior of the Tool The stresses in the container are determined
by the calculations based on elasticity. On the
Material under the Influence of
other hand, the calculation on an elastic/plastic
the Thermomechanical basis determines the service life. In addition to
Working Stresses determining the temperature distribution within
Containers are highly stressed both thermally the container over a defined number of working
and mechanically in extrusion. If the tempera- cycles in a given time, approximately 10 to 20
ture and stress state in the thick-wall container cycles, the stresses must be determined after a
sleeves results in localized plastic deformation, stable operating state has been reached in order
this first starts at the inner fibers of the liner. to determine the service life. It is possible to
Complete plastic deformation of the liner and, determine the service life of a container that has
in certain cases, of the liner holder and the man- undergone plastic deformation by FEM analy-
tle does not occur. Only in the area of the in- sis, using knowledge of the material parame-
terference fit can partial plastic deformation of ters. The analysis of a rectangular billet con-
the internal wall of the liner holder occur to a tainer [Mit 97] serves as an example. A
limited extent. It can therefore be assumed that container for aluminum alloys with an operat-
only localized plastic deformation of the liner ing temperature of approximately 500 ⬚C is in-
occurs. Stress variations are developed at the vestigated. In this temperature range, creep
internal and external diameter of the partially damage dominates with the hot working steels
plastically deformed liner that hardly change used, X38 CrMoV5-1 and X2 NiCoMo 18-9-5.
from the elastic stress state in the central region It is identified by fatigue tests at different load
of the liner wall as a result of creep. The radial frequencies. A method of service life prediction
stresses, on the other hand, are only slightly in- is used with creep/fatigue interaction in which
fluenced in the middle region. This is shown in the nonelastic strains and strain rates must be
Dubbel [1986]. known. They are obtained from the experimen-
If there is a buildup of heat in the container tal simulation of creep tests with the hot work-
from the high deformation temperature, the ing steels used.
elastic limit can be exceeded, so that plastic de- Restrictions must be made because of the ac-
formation, and consequently work hardening, tual operating conditions in extrusion:
1.2713 55NiCrMoV6 0.55 0.30 0.60 ... 0.70 0.30 1.70 0.10 ... . . . . . . . . . . . . ... ...
1.2714 56NiCrMoV7 0.56 0.30 0.70 ... 1.00 0.50 1.70 0.10 ... . . . . . . . . . . . . ... ...
1.2758 X50WNiCrVCo121 0.50 1.40 0.60 1.65 4.00 0.70 11.50 1.10 12.00 . . . . . . . . . . . . ... ...
1.2885 2 0.32 ... ... 3.00 3.00 2.80 ... 0.60 ... . . . . . . . . . . . . ... ...
1.2888 X32CrMoCoV333 0.20 0.25 0.50 9.50 8.50 2.20 ... ... 6.80 . . . . . . . . . . . . ... ...
... X20CoCrWMo109 ... ... ... ... ... ... ... ... ... . . . . . . . . . . . . ... ...
Austenitic hot working steels
1.2731 X50NiCrWV1313 0.50 1.35 0.70 ... 13.00 ... 13.00 1.30 1.30 ... . . . . . . ... 18.5 1450
1.2758 X50WNiCrVCo121 0.50 1.40 0.60 1.70 4.00 0.70 11.50 1.10 12.50 2.10 . . . . . . B ... ...
1.2779 2 0.05 1.00 2.00 ... 15.00 1.30 25.50 0.30 ... 2.10 . . . . . . B ⳱ 0.07 ... ...
... X6NiCrTi2615 ... ... ... ... ... ... ... ... ... ... . . . . . . ... ... ...
Cobalt-base alloys
2.4979 CoCr28MoNi 0.30 1.00 1.00 bal 28.00 5.50 2.25 . . . ... . . . . . . . . . ... ... ...
... Stellite 4 0.90 ... ... bal 26.00 ... ... . . . 15.00 . . . . . . . . . Nb ⬃13 1310
... Stellite 3 2.20 ... ... bal 36.00 ... ... . . . 16.00 . . . . . . . . . ... ... ...
2.9877 Stellite 6 1.10 ... ... bal 26.00 ... ... . . . 5.00 . . . . . . . . . ... ... ...
Nickel-base alloys
2.4668 NiCr19NbMo 0.05 ... ... ... 19.00 3.00 53.00 ... ... 1.00 0.60 ... B, Fe ... ...
2.4973 NiCr19CoMo 0.08 ... ... 11.00 19.00 10.00 bal ... ... 3.00 1.60 ... B, Fe 5.00 13.8 1320–1350
Molybdenum-base alloys
... TZM 0.02 ... ... ... ... ... ... ... ... 0.50 ... 0.08 ... 4.0 2610
... ZHM 0.08 ... ... ... ... ... ... ... ... 0.14 ... 0.72 Hf: 0.14 ... ...
... MHC 0.13 ... ... ... ... ... ... ... ... 1.50 ... ... 1.50 ... ...
Molybdenum-base metal-ceramic hot working materials
... Cermotherm 2015 ... ... ... ... ... 85.0 ... ... ... ... ... 15.0 ZrO2 ... 6.6 Sintered
Hard metals
... ... Co% WC% (Ta, Nb) C TiC max ... ... ...
... G3 (GT3) 12 88 0–2.50 1.00 ... 6.3 ...
... ... 25–30 bal 0–2.50 1.00 ... 7.0 Sintered
Ceramic hot working materials
... ... %ZrO2 %SiO2 %HFO2 %Fe2O2 ... ... ...
... Ziroca comp. 1027 99.50 0.30 Trace Trace ... 6.7 ...
... Ziroca comp. 2016 ... ... ... ... ... 7.0 Sintered
(a) CTE, cofficient of thermal expansion, 10ⳮ6/K, room temperature to 1000 K
Chapter 7: Extrusion Tooling / 519
● The load cycle must be idealized. hour the operating life is 250 hours. Mean-
● A ratio of the axial stem pressures to the while, the service life of liners has been in-
radially acting internal pressure must be as- creased significantly by container cooling in the
sumed. majority of applications.
● The container must be uniformly loaded
over the entire length.
● The temperature is constant in the container
(no temperature gradient). 7.11 Manufacture of Containers
● The interference pressure is uniform and
constant over the full length. The usefulness of a container depends to a
large degree on the shape and positional toler-
Knowledge of the material characteristic pa- ances in terms of straightness, angularity, con-
rameters for the hot working steel used for the centricity, coaxiality and runout according to
container components is necessary for a work- DIN 7184. The liner bore or the internal bore
ing-life determination. Because the material of containers with oval cross-sections (rectan-
characteristic parameters are not generally gular billet containers) based on the three da-
available but are known by the producers of the tum planes, longitudinal axis ⳱ A, horizontal
hot working steels, the user of the container axis ⳱ B, and vertical axis ⳱ C, the following
must rely on the data from the supplier. A have to be ensured within tight tolerances:
working-life prognosis is necessary to evaluate ● The end faces as contact faces are at a right
the economic viability of the container once the angle to the inner bore so that there is no
operating conditions have been specified by the tilting of the tool when load is applied.
user. ● The location of the container in the con-
An evaluation can indicate whether a work- tainer holder can be reproduced. In other
ing-life determination is necessary for a con- words, the centring keyways and the centr-
tainer that is subjected to plastic deformation, ing keys have to be parallel to the internal
even if only slightly. The steel application lists bore within tight tolerances.
201 and 202 of the VDEh (German Steel Fed- ● The liners and the mantle bore are cylindri-
eration guidelines) give permissible stress mag- cal. The liners (which also include the man-
nitudes for the most important hot working tle) must have constant wall thickness.
steels under “Material Properties” [VDE 85]. There must be no eccentricity. A uniform
The strength of a hot-working steel corre- interference pressure has to be guaranteed
sponding to the hot proof stress Rp0.2 is only and a common centre provided for all con-
valid for a brief temperature exposure. It does tainers used on an extrusion press.
not apply from the mechanical viewpoint to the ● The tolerances for the production of the
actual prolonged thermal exposure. This also container should be related to the tolerances
applies to the technical elastic limit Rp0.01. The of the extrusion press. These include a run-
deformations that arise from prolonged loads by out accuracy of 0.15/1000 mm for the fixed
material flow have to be taken into account. A dummy block, the runout for a tube press
comparison of the upper stress limits of the with a mandrel of 0.1/1000 mm, or, the run-
common hot-working steels including 1.2343, out for an extrusion press with a loose
1.2344, and 1.2367 show that the technical dummy block, for example, for brass wire,
elastic limit Rp0.01 is around 70 to 90% of the around 0.3/1000 mm.
hot proof stress Rp0.2 independent of the tem-
perature and that the creep stress for 1% elon- The production of the interference joint in a
gation after 1000 h is of the order of 45 to 55% container can vary whether two- or three-part
at 500 ⬚C and between only 6 to 10% at 600 construction. The machining of the rough
⬚C. The strength of the hot-working steels de- shaped component (hollow blank) to the fin-
creases further the longer the duration of the ished diameter dimension and the sequence of
loading and the higher the working tempera- the shrink fitting depends on manufacturing ca-
ture. This fact is true, in particular, with expe- pabilities. The interference value, which is the
rience in copper alloy extrusion plants. Conse- factor that determines the magnitude of the in-
quently, the working life of liners operating at terference pressure at the interface, is the dif-
high temperatures is often less than 10,000 ex- ference between the diameters of two hollow
trusions. This means that at 40 extrusions per bodies that have to be fitted together. The in-
520 / Extrusion, Second Edition
terference value is given as an absolute value (actual value), and eiby is the interference value
relative to the nominal value, or generally as a for the liner (relative interference).
0/00 (per thousand) value. The overvalue as the The external diameter of the liner set, con-
interference value is added to the actual value sisting of the liner holder and the liner, is finish-
of the bore, and this gives the dimension of the machined according to the actual value of the
external diameter of the sleeve that is to be fit- bore of the finished container mantle. The di-
ted. It can also be calculated in the opposite mension for the external diameter of the liner
way, starting from the actual value of the ex- set is determined as follows:
ternal diameter of the sleeve and machining the
bore with the corresponding interference value. d3zb ⳱ d3m Ⳮ (ezbz) ⳯ d3m
The same interference value is used for both
manufacturing methods. The interference value where d3zb is the outside diameter of the liner
addition therefore depends on whether the ref- set (liner holder), d3m is the inside diameter of
erence dimension taken from the opposing sur- the mantle (actual value), and ezbz is the inter-
face stems from a free hollow body or from a ference value for the liner holder with the fitted
hollow body in which another has already been liner (relative interference).
shrunk in. The sequence of fitting, whether
from the inside to the outside or from the out-
side to the inside, must be taken into account.
Fitting from the inside to the outside is pre- 7.12 Container Operation
ferred. Starting from the bore, the actual value
for shrink-fitting is determined from at least Careful consideration must be given to the
five measurements taken crosswise and distrib- container working temperature, which is im-
uted uniformly over the length. The external di- portant for the press operation. The working
ameter of the liner to be fitted is then produced, temperature must be reached before extrusion
taking into account the interference value. The commences. The heating rate must not exceed
material of the component determines the in- the maximum of 60 ⬚C (108 ⬚F) per hour. With
terference value. It must be calculated. After faster heating, there is the risk that the container
shrink-fitting, the internal bore of the container will not be uniformly heated. The function of
is remachined. This ensures that the internal the interference fit cannot then be guaranteed.
bore is cylindrical and dimensionally correct. The liner is then overstressed and/or slips. If
The interference value for a two-part con- the container is heated in the press, it should
tainer is determined as follows. The external not be sealed against the tool stack, to avoid
diameter of the liner is finish-machined accord- liner slip.
ing to the actual value of the bore of the fin- Both ends of the container bore should be
ished mantle. The dimension of the external di- closed during prolonged downtime. This pre-
ameter of the liner is calculated from: vents the temperature of the liner from falling
below the temperature of the mantle. Standard
d2ib ⳱ d2m Ⳮ (eibx) ⳯ d2m practice is to close the bore at one end, with
the stem and the die set at the other end—with-
where d2ib is the outside diameter of the liner, out the container sealing load. The interference
d2m is the inside diameter of the mantle (actual forces are reduced significantly, even with a
value), and eibx is the interference value for the temperature difference of only 50 ⬚C (90 ⬚F)
liner (relative interference). between the mantle and the liner. The result is
The interference value for a three-part con- that the safe equivalent stress is exceeded dur-
tainer is determined as follows. After determin- ing production. In addition, the action of the
ing the actual value of the liner holder bore that container sealing force can result in liner slip.
has been produced with a provisional excess on If a “sticker” occurs (a billet seized in the
the external diameter, the dimension for the ex- container), it should be removed from the con-
ternal diameter of the liner is determined: tainer as quickly as possible, particularly if the
billet temperature exceeds 550 ⬚C. The life of
d2ib ⳱ d2zb Ⳮ (eiby) ⳯ d2zb the liner and, in some cases, the liner holder
can be significantly reduced by such a mishap.
where d2ib is the outside diameter of the liner, The location of the container in the press
d2zb is the inside diameter of the liner holder must be central and aligned with the stem. It is
Chapter 7: Extrusion Tooling / 521
particularly important with rod and tube presses The replacement of worn liners is an essen-
(integral piercer) and extrusion presses with tial procedure in the maintenance of containers.
fixed dummy blocks to maintain the tooling When this takes place, the condition of the en-
alignment accuracy specified by the manufac- tire container must be assessed and, if neces-
turer. With short-stroke presses, accurate central sary, repairs carried out.
location of the container is also required. The Condition monitoring of the complete con-
central location of the tooling to each other is tainer and the procedure for liner replacement
important for both safety and also for process include:
technical requirements.
1. The number of extrusions at the average
operating temperature, extrusion time, the
7.13 Maintenance of Containers number of stickers at the billet temperature
x ⬚C, and the delay before removal from
The design drawing, with the associated the container
manufacturing specifications, shrinkage speci- 2. The state of the liner close to the end faces
fications, and production protocol, is needed for and in the bore
the maintenance of containers. 3. Dropping out of old liners. If they cannot
Defect prevention should be the main focus be dropped out because of bulging in the
for the maintenance of containers. The operat- middle, then removal by machining is nec-
ing and maintenance personnel should be essary.
trained accordingly. 4. Actual bore of the liner holder or the man-
Attention should be paid to: tle at room temperature at intervals of 100
mm, crosswise. With a three-part design,
● Heating and cooling of containers should
subsequent control of the interference joint
follow the guidelines of the manufacturer.
mantle/liner holder by ultrasonic inspection
● Stickers are billets in the container that can-
is necessary.
not be extruded. They must be immediately
5. Monitoring the mechanical properties of
removed from the container if the billet
the liner holder and/or the mantle
temperature exceeds 550 ⬚C. Heat transfer
6. Control of the centering and locking faces
to the liner takes place particularly quickly
on the mantle external diameter for wear.
and intensively in the upset condition.
Mating parts should also be inspected. Any
● Temperature control matched to the produc-
damage should be repaired according to the
tion and monitored for protection of the
drawing.
container is recommended for quality rea-
7. Remachining of the bore of the liner holder
sons for aluminum alloys and is necessary
or the mantle, corresponding to the shape
for copper alloys. Intensive cooling of the
and dimensional tolerances
critical zones within the container is essen-
8. Machine the external diameter of the new
tial for extrusion temperatures over 600 ⬚C.
liner to the resultant dimensions of the new
● Clean contact faces between the extrusion
bore with the shrinkage additions.
tools (dies, die holder, and hollow dies) and
9. Shrink-fitting of the liner
the end face of the liner are necessary.
10. Finish-machining of the liner after shrink-
● Alignment of the extrusion stem to the con-
fitting to the shape and dimensional toler-
tainer must be ensured. Alignment errors
ances
can easily result in damage to the liner wall
11. Condition and functional control of the
in the container.
heating, with repair if necessary
● Air inclusions within the container must be
avoided. The explosive release of the highly The operating procedure should be docu-
compressed air in the area of the die and the mented. The most important data can then be
container liner can result in damage to the used to improve the working life and possibly
tooling. bring about a future cost reduction.
522 / Extrusion, Second Edition
C 0.1/1000 A 0.1/1000 A
0.1/1000 A
0.1/1000 C
0.05/1000
A
0.03/1000
0.1/1000 A
0.1/1000A
0.1/1000C 0.1/1000 A
0.1/1000 A 0.1/1000 B 0.01/1000
0.1/1000 B
steels. Carbides primarily control the hot ● Tungsten forms the low-solubility carbide
strength, the tempering resistance, and the (FeW)6C. The alloying element plays a sig-
wear resistance of the hot working steels. nificant role in secondary hardening by car-
● Increasing silicon content increases the bide precipitation at high tempering tem-
yield strength and the fracture strength but peratures. In addition, tungsten promotes
also reduces the toughness of the hot work- fine grains in hot working steels and im-
ing steels. proves the hot strength as well as the wear
● Manganese reduces the critical cooling rate resistance.
and, even in small quantities, promotes the
hardenability and the ability to through- The majority of hot working steels with spe-
harden. Manganese also displaces the pearl- cial carbide-forming elements are capable of
ite point to the left in the iron-carbon dia- secondary hardening under suitable tempering
gram. conditions. This is precipitation hardening.
● Nickel promotes the through-hardening and While the strength (hardness) falls with increas-
the hot strength of the hot working steels ing tempering temperature because of iron car-
without significantly reducing the tough- bide precipitation, it increases significantly with
ness. In addition, similar to manganese, it certain hot working steels above 450 to 550 ⬚C
reduces the critical cooling rate and acts as by the precipitation of special carbides in the
a grain refiner. Nickel does not form any martensitic matrix of the steel and the break-
carbides and tends toward temper embrittle- down of the residual austenite. As shown in
ment. This tendency can be compensated by Fig. 7.110, a hardness or strength maximum oc-
other elements. curs that falls again after exceeding this tem-
● Chromium is the most important alloying perature range. The special carbides mentioned
element in tool steels. It reduces the critical are difficult to dissolve but also precipitate
cooling rate and, together with carbon, con-
trols the hardness and thus the strength as
well as the wear resistance. Chromium pro- 2200
motes the hardenability, that is, the ability 2100
of the tool steel to through-harden even with
2000
thicker cross sections. It also improves the
temper resistance of the hot working steel 1900
slowly in the martensitic matrix. A particularly to the static 0.2% hot proof stress in a tem-
high volume of carbides needs to be dissolved perature range of 500 to 600 ⬚C [Güm 81].
to achieve a high tempering resistance, that is, The 0.2% proof stress of hot working steel
the degree of carbide solubility determines the decreases in the crystal recovery range with in-
maximum strength that can be achieved during creasing load duration. The dependence of the
tempering as well as the tempering resistance. creep strength on the hardened and tempered
The hardening temperature must be correspond- strength of the hot working steel is shown in
ingly high; however, excessively high harden- Fig. 7.111 for several different heat treated hot
ing temperatures must be avoided, because this working steels [Güm 81, Hab 77]. The creep
would result in grain coarsening and thus affect strength of the tool material is responsible for
the toughness of the hot working steel. the shape and dimensional stability of an extru-
If the tempering temperature is significantly sion tool. Exceeding this value results in plastic
exceeded, the hot working steel softens to an
increasing extent and starts to creep and flow
under the influence of the extrusion forces, as
can be seen in Fig. 7.109, which shows a ther-
momechanically overloaded four-cavity extru-
sion die for the production of brass wire. The
loading on the material of an extrusion tool dur-
ing the press cycle is given in Table 7.14.
Extrusion tooling is subjected to tempera-
tures that frequently fall in the crystal recovery
range of the tool material. The duration of the
loading in the extrusion cycle depends primar-
ily on the possible extrusion speeds and can
thus range from 10 s to approximately 20 min.
Accordingly, with short extrusion times, the
loading can be referred to as fatigue, and with
longer times, as periodically interrupted creep
loading, because with long loading times, time-
dependent changes can occur in the tool mate-
rial under thermal and mechanical stresses.
Table 7.11 gives characteristic values for the
dynamic behavior of different hot working
steels in the tensile fatigue range at a tempera-
ture of 500 ⬚C compared to the static 0.2% hot
proof stress [Wan 72]. A similar comparison is
shown in Fig. 7.107 for the 0.2% 100 h creep Fig. 7.111 Dependence of the creep strength of various
hot working steels on the testing temperature at
limit for the hot working steel 1.2343 compared various heat treated strengths [Güm 81]
Table 7.14 Fluctuating loads on tool materials during the extrusion cycle that cause creep fatigue,
oxidation, or wear
Thermomechanical Thermal
● Fluctuating compressive forces during the extrusion cycle ● Fluctuating thermal stresses in the extrusion cycle
● Fluctuating tensile forces during the extrusion cycle ● Fluctuating temperature-related forces in the extrusion cycle
● Fluctuating bending forces in the extrusion cycle
● Alternating stress concentrations at unavoidable notches in the
shape-forming die aperture
Chemical Tribological
● Oxidation on heating ● Wear on the tool working surfaces during extrusion resulting
● Heat retention and cooling in the surrounding medium from adhesion and abrasion by the flowing extruded material
● Grain-boundary attack of hot-working steels by tin- and
copper-containing low-melting-point phases in the extruded
material, with melting points below the deformation
temperature
Source: [Ber 82]
526 / Extrusion, Second Edition
deformation in the shape-forming areas of the possible [Ber 82, Ber 76]. This requirement is
tool. not met by all hot working steels, as can clearly
With inserted dies, the die body in hot work- be seen in the time elongation curve in Fig.
ing steel prestressed by the shrink-fitting of the 7.113 for the steel 1.2567. The hot working
insert is subjected to a permanent creep loading steel 1.2365 exhibits a similar behavior at a
in the working condition that can loosen the working temperature of 500 ⬚C, depending on
composite. its heat treated strength. This is shown in Fig.
Under thermomechanical creep loading, 7.114 by the time elongation curves for this
steels susceptible to deformation exhibit a de- steel at different heat treated strengths. These
formation process similar to that shown in Fig. hot working steels also exhibit creep embrittle-
7.112 for the hot working steel 1.2343 at a tem- ment with increasing strength, and there is a
perature of 500 ⬚C and different loads. After close relationship between creep embrittlement
high initial values, the creep rate decreases after and hot embrittlement of steel [Ber 82].
a specific load duration as a result of work These embrittlement mechanisms become
more effective with increasing heat treated
hardening of the steel. The creep rate remains
strength. In addition, steels that are less suscep-
practically constant for a specific time with in- tible to hot embrittlement are also less suscep-
creasing total elongation and then rapidly in- tible to creep embrittlement. However, creep
creases again. This increase is attributed to the embrittlement commences at temperatures of
softening process in the steel that occurs after approximately 100 ⬚C lower than hot embrittle-
extensive thermomechanical loading. The creep ment. This material-specific behavior of hot
process of steel up to failure is correspondingly working steels must be taken into account in
divided into three regions: the primary creep selection, along with the extrusion tool loading.
region, the secondary creep region, and the ter- Extrusion tools that tend toward plastic defor-
tiary creep region. In order to avoid failure after mation as a consequence of the thermomechan-
a relatively short load duration, hot working ical stresses can unexpectedly fail from creep
steels should accordingly have a maximum pos- embrittlement.
sible secondary creep range; that is, in this The creep behavior of hot working steels can
creep phase, the creep rate should be as low as be favorably influenced by the special carbide-
Fig. 7.112 Creep behavior of the hot working steel 1.2343 under different loads and creep rates as a function of creep elongation.
The diagram shows the three creep phases: primary creep, secondary creep, and tertiary creep [Ber 76]
Chapter 7: Extrusion Tooling / 527
Fig. 7.113 Creep elongation curves for the hot working steels 1.2714, 1.2343, 1.2567, and 1.2886. The different steels exhibit
ductile and brittle creep behavior [Ber 76]
1.2 T = 500° C
= 680 N/mm2
1.0
Total strain, %
Rm = 1200 N/mm2
0.8
x = Fracture
Rm = 1400 N/mm2
0.6
0 100 200
Time, h
usually caused by notch-related stress concen- resistance of the steels did fall above 500 ⬚C
trations from the mechanical loading. but only slightly [Kre 78]. The carbon reduc-
Basically, the toughness decreases with in- tion resulted, in particular, in a reduction in the
creasing initial strength, as shown in Fig. 7.116, segregation tendency of the hot working steel
by the notch impact values as a function of the and thus to less microsegregation by chromium,
tensile strength. Figure 7.116 also gives the de- molybdenum, and vanadium [Dez 71]. This im-
pendence of the toughness on the direction of proves the transverse toughness to some extent.
working of the hot working steel; that is, the The silicon content also influences the suscep-
toughness values are better in the forging di- tibility to segregation. Consequently, the trans-
rection than in the transverse direction. During verse toughness is also improved by its reduc-
forging, elongated crystal segregations and sul- tion. One example is the steel 1.2367, which,
fides reduce the toughness in the transverse di- for a long time, was not readily used for the
rection. manufacture of hollow section dies for the ex-
The material characteristic parameters, par- trusion of low-alloyed aluminum alloys in spite
ticularly the hot toughness, of certain hot work- of its good initial strength, because of the mod-
ing steels can be significantly improved by re- est toughness values. The optimization de-
ducing the sulfur content and by optimal scribed has changed this. The same thing ap-
balancing of the alloying elements with each plies to the hot working steel 1.2885, which,
other. Reducing the carbon content in hot work- after optimization, has proved to have excellent
ing steels with chromium contents of approxi- temper resistance and thus shape stability in the
mately 5% by weight, for example 1.2343, hot spots of large hollow dies for the production
1.2344, and 1.2367, gave a definite improve- of aluminum profiles.
ment in the hot toughness in general and in the Hot working steels have a tendency for hot
transverse direction in particular. The tempering embrittlement in the temperature range of 500
to 650 ⬚C, depending on the chemical compo-
sition, manufacturing conditions, heat treated
strength, and heat treatment. In this temperature
2000
range, there is a significant loss in ductility.
High hardening temperatures and cooling
1900 rates that are too slow can result in a consid-
erable loss in toughness after austenitizing; for
1800 example, raising the hardening temperature
does increase the fracture strength and the tem-
pering resistance but also reduces the tough-
1700
ness.
Tensile strength, N/mm2
Tensile strength
1)
0.2 proof stress
2)
3)
4)
5)
6)
7)
Fig. 7.117 Comparison of hot strength with reduction in area as an indication of the hot strength of the following hot working
steels at a testing temperature of 600 ⬚C. 1:1.2714 ⳱ 56 NiCrMo7; 2: 1.2343 ⳱ X38 CrMoV51; 3: 1.2344 ⳱ X40
CrMoV51; 4: 1.2367 ⳱ X40 CrMoV53; 5: 1.2365 ⳱ X32 CrMoV33; 6: 1.2567 ⳱ X30 WCrV53; 7: 1.2888 ⳱ X20CoCrWMo109
[Güm 81]
1800 1800
Rm
Rp0.2 limit and Rm, N/mm2
1400 1400
Rm
Enlongation to failure (A10) %
Fig. 7.118 Comparison of the hot strength and hot toughness of the hot working steels (a) 1.2343 and (b) 1.2567 [Bar 81]
ever with the steel 1.2567, the increase in hot 7.119 on an extrusion mandrel, resulting in pre-
toughness changes into a rapid loss in hot mature failure. This network of thermal cracks
toughness above 500 ⬚C. In principle, however, is caused by fluctuating tensile/compressive
the hot toughness of the hot working steels in- stresses in the working surfaces of the extrusion
creases with temperature, which is important tooling. They develop from the temperature dif-
for the thorough preheating of the extrusion ferences that occur during the extrusion cycle
tooling before use. between the tool surface and the core material
Extrusion tooling for direct forming sub- below it. This fluctuating loading in the tension
jected to permanent temperature fatigue loading compression range is particularly harmful in
at high deformation temperatures during the ex- thermally highly loaded tools that are externally
trusion cycle frequently fails by hot crack for- cooled between the individual extrusions. This
mation. The hot stress cracks extend as a net- method of cooling cannot always be avoided
work over the tool surface, as shown in Fig. under certain working conditions in order to
530 / Extrusion, Second Edition
Fig. 7.119 Hot cracking network on the working surface of a tapered extrusion mandrel in the hot working steel 1.2367 for the
production of copper tubes, resulting from the fluctuating tensile and compressive stresses. Copper that has welded
to the mandrel surface can be seen in the lower right and left areas of the photograph. Source: Wieland–Werke AG
avoid heating the tool material well above the that hot cracks are comparable to fatigue cracks
tempering temperature. During cooling, the sur- under mechanical/dynamic loads. Therefore,
face of the tool will assume a smaller volume procedures that increase the fatigue strength of
than the core cross section of the tool, because hot working steels should also improve the re-
of the lower temperature. This results in tensile sistance to thermal cracking. The purity and ho-
thermal stresses in the working surface of the mogeneity of the hot working material and, in
tool. During extrusion, the working surface is particular, the heat treatment selected for a spe-
reheated to a higher temperature than the tool cific loading application are important to
core cross section. This results in compressive achieve a good relationship between the hot
thermal stresses in the working surface. If these strength and the hot toughness [Güm 81].
fluctuating stresses in the tension/compression The hot wear resistance of the hot working
range exceed the elastic limit of the hot work- steel is very important for the shape-producing
ing material, then plastic deformation occurs, tooling and the container liner. Wear is char-
and this ultimately results in the formation of a acterized by material loss, and adhesive and
typical hot crack network on the surface of the abrasive wear as well as fatigue wear can occur
tool. The effect of the fluctuating temperature on the working surfaces of the tool, for exam-
is particularly severe with hot working steels ple, on mandrel surfaces. This wear impairs, in
with low thermal conductivity. However, in particular, the shape-producing regions of ex-
spite of the use of the CrMoV steels with better trusion tools used to produce tubes and section
thermal conductivity, hot cracking from rapid to the finished dimensions. Even slight wear of
temperature fluctuations during the extrusion the tool working surface can have an extremely
cycle at high deformation temperatures cannot negative influence on the material flow. Con-
always be prevented. In this context, there is no sequently, hot working steels used for the man-
hot working steel completely resistant to tem- ufacture of these tools should have the optimal
perature fluctuations. However, the working life high wear resistance. The working temperature
of extrusion tooling subjected to temperature plays a role in this requirement, because semi-
fluctuations can be optimized by careful bal- finished products in materials extruded at high
ancing of the material properties responsible for temperatures are not normally finish-extruded.
the ability to resist temperature fluctuations, in- In terms of wear, the compatibility of the
cluding hot flow stress, hot strength, hot tough- friction partners hot working steel and extruded
ness, and temper resistance, through the heat material can be improved by surface treatment
treatment. Experimental results have indicated of the extrusion tooling, in which the chemical
Chapter 7: Extrusion Tooling / 531
composition of the tool surface is changed. Ni- ticular tend to weld to the tool steel. However,
triding is a well-proven process in this respect. because aluminum alloys can be extruded at
Recently, there has been some initial success relatively low temperatures, the welding of the
with chemical vapor deposition (CVD)-applied extruded material to the tool working surface
surface coatings. With these processes, the tool can be reduced by a surface treatment, for ex-
surface is further hardened or coated, which ample, nitriding. The welding cannot, however,
significantly improves the wear resistance. The be prevented. In contrast, the shape-forming ex-
tool working life is then considerably im- trusion tool areas for the extrusion of copper
proved. alloys are lubricated so that welding of the cop-
The results from wear studies using hot tor- per alloy to the tool working surface does not
sion tests with the friction partners extruded occur.
material/hot working steel for different ex- Under certain conditions, corrosion attack by
truded material are shown in Fig. 7.120 and the extruded material at the grain boundaries of
7.121. The increase in the wear depends on the the hot working steel on the tool working sur-
extruded material, the working temperature, faces can take place during extrusion. This at-
and the duration of loading. tack is a specific form of stress-corrosion crack-
During the extrusion process, reactions can ing in which the liquid extruded material or a
occur between the extruded material and the low-melting-point phase penetrates into the
tool material, including: grain boundaries of the hot working material
under tension, as can be seen in Fig. 7.122.
● Tribological reactions by adhesion, resulting Container liners are particularly affected by this
in welding under pressure and temperature type of corrosion attack, because they are sub-
of the extruded material to the tool working jected to tensile stress peaks in the bore during
surface the extrusion cycle. This corrosion attack oc-
● Chemical reaction by corrosion attack of the curs basically under the following conditions:
extruded material at the grain boundaries of ● The extruded material or a low-melting-
the hot working steel point phase must be soluble in iron, for ex-
The tool working surfaces usually deteriorate ample, tin and copper, and the liquidus tem-
perature must be exceeded during the
rapidly from adhesion as a result of the weld-
deformation.
ing, as does the surface of the semifinished ● The wetted surfaces of the hot working steel
product after a certain production time. Of all must be subjected to tensile stresses above
the materials extruded, aluminum alloys in par- a critical value.
If these conditions are fulfilled, the liquid ex-
truded material rapidly attacks the grain bound-
3.0
870° C
2.0 800° C
730°C 5.0
1.0 690°C 4.0
0.8 650° C
0.6 3.0
600° C
Wear, mm
550° C 1.0
460° C 0.8
0.1
0.08 0.6
0.06
Al Mg Si 0.5 0.4
0.04 Al Mg Si Q5/20’
Ms 58
Ms 58 /20’
Cu Ni 30
0.02 0.2 Cu Ni 30 /4’
0.01
4 8 12 16 20 24 28 0.1
Time, min 450 500 550 600 650 700 750 800 850 900
Temperature, °C
Fig. 7.120 Time-dependent wear rates from hot torsion
tests for the hot working steel 1.2779 as the ro- Fig. 7.121 Wear rates of the hot working steels used after
tating steel heated to 550 ⬚C and the extruded materials Al- 20 min test duration, corresponding to Fig.
MgSi0.5, CuZn42 and CuNi30 heated to the deformation tem- 7.130 as a function of the deformation temperatures of the three
perature [Schi 82] extruded materials used [Schi 82]
532 / Extrusion, Second Edition
Fig. 7.122 Solder fracture in the liner of the container of an aluminum extrusion press with a 250 mm bore after a large number
of extrusions with the bearing material AlSn6Cu1. The liner was manufactured in the hot working steel 1.2306.
Source: VAW
aries of the hot working steel. It rapidly pene- tween a conventionally cast ingot preferentially
trates along the grain boundary into the tool solidified with columnar crystals transverse to
material. Intercrystalline failure of the hot the axis, and an ingot remelted by ESR, which
working steel then occurs under tensile stresses, has solidified with a significantly finer and
because liquid metals cannot withstand any ten- more uniform grain size. The material param-
sile forces. This special case of intercrystalline eters are more uniform and less orientation de-
stress corrosion is also referred to as solder pendent. The ESR-remelted steels are more ex-
cracking. The risk of solder cracking increases pensive and therefore used for complicated
with the temperature of the tool material. There hollow dies.
is practically no remedy against the suscepti- The success of both processes has resulted in
bility to solder cracking. Higher chromium and a qualitative division between the hot working
silicon contents in the hot working steels do steels according to the method of manufacture.
reduce the susceptibility to solder cracking, but Hot working steels that only receive the sec-
this material defect can only be prevented by ondary metallurgy process during manufacture
reducing the deformation temperature below to obtain a higher microscopic purity are con-
the liquidus temperature of the extruded mate- sidered by the extrusion plant as fine-grade
rial by the selection of a suitable extrusion pro- steels, and those that are additionally remelted
cess. with the ESR process as extra-fine grade.
The production methods for hot working Based on this classification, fine-grade steels
steels have been significantly improved by sec- are used for the manufacture of extrusion tool-
ondary metallurgy and electroslag refining ing subjected to moderately high thermome-
(ESR). chanical stresses and extra-fine grade is used for
In the melt treatment using secondary met- the manufacture of extrusion tooling subjected
allurgy, for example, with argon injection, the to high thermomechanical stresses, for example,
melt is purified to give significant reductions in aluminum hollow dies.
elongated manganese sulfide and segregation The blank ingots are forged after diffusion
bands, improving the transverse toughness val- heat treatment. Sawn blanks from forged round
ues. bars—particularly in the extra-fine grade—are
In the ESR process, the steel is remelted in suitable for the manufacture of dies. If the best
an arc furnace and solidified after the passage possible transverse toughness values are re-
of a refining slag in a water-cooled mold. Fig- quired, then three-dimensionally forged blanks
ure 7.123 shows the difference in structure be- must be used.
Chapter 7: Extrusion Tooling / 533
Hardening temperature
1000° C
1. First step
salt bath
780° C
Temperature
Preheat stage
400° C Air Air Air Air
Time
Fig. 7.124 Schematic diagram of the salt bath heat treatment sequence for hardening the hot working steel 1.2343 [Ame 71]
Further cooling in air can only be carried out with dimensional changes. Because hot work-
after the extrusion tooling has completely ing steels do not have large quantities of resid-
reached the quenching temperature. Before re- ual austenite, the reduction of residual austenite
heating for tempering, the extrusion tool should by tempering suffices.
be held for some time at an equalization tem-
perature of 80 to 100 ⬚C. As described in Fig.
7.124, this is followed by three tempering tem- 7.14.1.2 Machining of Hardened and
peratures each of 4 to 6 h holding time and the Tempered Hot Working Steels
temperature sequence of 580, 590, and 540 ⬚C. The manufacturing cost of an extrusion tool,
Tempering also requires thorough through-heat- which is the most important production item in
ing with moderate heating rates to avoid detri- the extrusion plant, influences the economic
mental thermal stresses. This also applies in re- success. The extrusion plant therefore requires
verse to the cooling phase. This should take the tool maker to use the most economic mod-
place in absolutely still air and last at least 2 h ern production methods.
or longer. Three-staged tempering should result The introduction of spark erosion machining
in the following effects in the hot working steel: of extrusion tool blanks for the production of
● Secondary hardening the die aperture has resulted in significant re-
● Thermal stress relieving ductions in the production times and hence the
● Transformation of the residual austenite in costs. Cutting out the die aperture from the heat
the steel structure into martensite or bainite treated material using wire erosion can replace
● An increase in the toughness of the hot sawing from the unheated die blank and sink
working steel from the third tempering stage erosion to the final dimensions after heat treat-
ment. The spark erosion machining influences
The transformation of residual austenite in the newly formed surface of the hot working
the tool material can result in dimensional steels that will subsequently form the tool
changes from stresses within the extrusion tool, working surfaces in the die aperture as a func-
because the transformed structure has a differ- tion of the cutting rate. For this reason, the ef-
ent volume than the austenite. These dimen- fect on the hot working steels at these cut sur-
sional changes in the shape-forming areas of faces is of considerable importance.
the tool can be removed during the final pro- Figures 7.125 and 7.126 show the changes in
duction. In contrast, a residual austenite trans- the machined hot working steel surfaces result-
formation when the tool is used in production ing from spark erosion machining. A molten
can result in production problems associated zone forms on the surface, and beneath this, a
Chapter 7: Extrusion Tooling / 535
fuse from the diffusion zone into the interior of working life than nitriding (Fig. 7.127). These
the tool material after the tool has been used coatings are extremely wear resistant. The sur-
for a specific time. As a consequence, the sur- face finish of the treated tool does not deterio-
face hardness decreases, as shown by hardness- rate like nitrided surfaces, even after a large
against-depth curves [Sar 67]. These processes number of extrusions. In addition, it is not nec-
occur particularly in aluminum extrusion tools essary to clean the die of aluminum when an
and especially in hollow dies because of the order has been completed. Instead, for example,
higher deformation temperatures. This is asso- a hollow die can remain full of aluminum, pro-
ciated with a reduction in the surface quality of vided the start of extrusion of a new order will
the extrusion, which continues to deteriorate. not impair the shape-producing capability of the
The die must be renitrided to regain the old die.
capacity. In the production of aluminum semi- The disadvantage of these coating processes
finished products, the following program, based is the high coating temperature of over 1000
on experience, is typically followed: ⬚C. The extrusion tools can therefore only be
heat treated after the CVD coating, with the
● After the first nitriding, approximately 40 to tool to be hardened heated to the coating tem-
50 extrusions perature and then tempered from this tempera-
● After the second nitriding, approximately 60 ture. This can give distortion problems with
to 80 extrusions larger tools.
● After the third nitriding, approximately 80
to 100 extrusions
● After the fourth nitriding, approximately 7.14.2 Austenitic Hot Working Steels
100 to 140 extrusions
● After the fifth nitriding, until the die fails Thermomechanical stresses that are too high
for the classic hot working steels in hot extru-
During renitriding, the compound zone natu- sion require the application of higher hot
rally increases in thickness. This is one of the strength hot working steels. The high-tempera-
reasons why the compound zone should only ture austenitic hot working steels should first be
be a few micrometers thick after the first nitrid- considered. These do have naturally lower me-
ing. chanical properties; however, they can be sub-
Extrusion tooling coated by CVD with tita- stantially work hardened if the steel is thermally
nium and chromium carbide as well as alumi- stressed below its recrystallization temperature.
num oxide provides a significantly longer The increase in the flow stress due to work
Fig. 7.127 Left, chemical vapor deposition (CVD)-coated aluminum extrusion dies. Right, demanding heat exchanger sections
in AlMgSi0.5 produced with CVD–coated dies. Source: WEFA Singen Gmbh
Chapter 7: Extrusion Tooling / 537
1400
1200
Hot yield point, N/mm2
100 1.2344
800
1.2779
600
400
200
300 400 500 600 700 800
Testing temperature, °C
Fig. 7.128 Comparison of the 0.2% hot proof stress of the classic hot working steel 1.2344 with the austenitic hot working steel
1.2779 [Kor 95]
538 / Extrusion, Second Edition
Table 7.15 Hot working steels for extrusion tools for the direct and indirect extrusion of aluminum
and copper alloys
Nominal composition, wt%
Material No. Abbreviation C Co Cr Mo Ni V W Ti
1.2311 40CrMnMo7 0.40 . . . 2.00 0.20 ... ... . . . . . .
1.2323 48CrMoV51 0.45 . . . 1.45 0.75 ... 0.30 . . . . . .
1.2713 55NiCrMoV6 0.55 . . . 0.70 0.30 1.65 0.10 . . . . . .
1.2714 56NiCrMoV7 0.55 . . . 1.10 0.50 1.65 0.10 . . . . . .
1.2343 X38CrMoV51 0.38 . . . 5.20 1.25 . . . 0.40 . . . . . .
1.2344 X40CrMoV51 0.40 . . . 5.20 1.35 . . . 1.00 . . . . . .
1.2365 X32CrMoV33 0.32 . . . 3.00 2.80 . . . 0.55 . . . . . .
1.2367 X40CrMoV53 0.38 . . . 5.00 3.00 . . . 0.55 . . . . . .
1.2567 X30WCrV53 0.30 ... 2.35 0.60 ... ... 4.25 ...
1.2581 X30WCrV93 0.30 ... 2.65 0.35 ... ... 8.50 ...
1.2678 X45CoCrWV555 0.45 4.50 4.50 0.50 ... 2.00 4.50 ...
1.2885 X32CrMoCoV333 0.32 2.80 3.00 2.80 ... 0.60 ... ...
1.2889 X45CoCrMoV553 0.45 4.50 4.50 3.00 ... 2.00 ... ...
1.2731 X50NiCrWV1313 0.50 ... 13.00 ... 13.0 1.30 1.30 ...
1.2758 X50WNiCrVCo1212 0.50 1.70 4.00 0.70 11.5 1.10 12.50 ...
1.2779 X60NiCrTi2615 0.05 ... 15.00 1.30 25.5 0.30 ... 2.10 Ⳮ B
Source: [Kor 95]
tions to overcome higher thermomechanical for hot extrusion of copper-zinc alloys. Hot
loading, for example, as the material for con- working steels in the third group, based on
tainer liners for copper alloy extrusion and as WCrMo, are used for extrusion tools for the hot
dies or die inserts for copper tube and copper working of copper alloys. They have very good
sections as well as dummy blocks. The extru- wear properties but poor thermal conductivity,
sion of brass alloys with low zinc contents a property that promotes hot spots, particularly
(Tombak) only became economic with the use on the surface of extrusion mandrels. Therefore,
of dummy blocks in the austenitic steel 1.2779 these tool steels have lost their importance. Co-
[Kor 97]. However, austenitic steels have high balt-containing hot working steels of the fourth
coefficients of expansion, a property that must group have good high-temperature strengths
be taken into account when determining the in- and are therefore used for extrusion tools sub-
terference fit for shrink-fitting an austenitic jected to high thermomechanical stresses, in-
liner into the hot working steel liner holder of cluding the extrusion of copper alloys but also
a copper alloy container. the center of the shape-producing areas of large
aluminum hollow sections. Finally, the austen-
itic-based hot working steels in the fifth group
7.14.3 Classification of
have better temper resistance than those listed
Hot Working Steels previously. They are suitable mainly as the ma-
Hot working steels for extrusion tools are terial for extrusion tools for copper alloy extru-
specified in the steel application list of VDEh sion. They have proved particularly suitable for
201 for extrusion tools for copper alloys as well die inserts.
as in 202 for extrusion tools for magnesium and The quality of the hot working steels in Ger-
aluminum alloys. The most important ones are many is governed by the following standards.
given in Table 7.15. They can be classified into These can be used to supply specifications for
five groups. the materials for specific requirements of extru-
Low-alloy tool steels in the first group are sion tools. The standards include:
used for extrusion tools that only have indirect ● DIN 50 115 “Testing of Metallic Materials,”
contact with the extruded material, for example, notch impact bending tests
support tools. The more highly CrMoV-alloyed ● Steel application list 201, materials for tools
tool steels in the second group are mainly used for tube and rod extrusion of copper and
for the manufacture of extrusion tools for hot copper alloys
working aluminum alloys that come into direct ● Steel application list 202, materials for tools
contact with the extruded material. They are for tube and rod extrusion of aluminum and
also used to a limited extent for extrusion dies aluminum alloys
Chapter 7: Extrusion Tooling / 539
cobalt alloys can only be used up to a maxi- These alloying elements form titanium and zir-
mum of 1000 ⬚C [Kor 97]. conium solid solutions with a fine dispersion of
TiZr carbides that significantly increase the hot
7.15.2 Molybdenum Alloys strength. In addition, the carbides raise the re-
crystallization temperature to above 1300 ⬚C.
While high-temperature cobalt and nickel al- Even at the high deformation temperatures as-
loys can withstand deformation temperatures up sociated with the extrusion of iron alloys, the
to 1000 ⬚C, hot working materials based on temperature is below this recrystallization
high-melting-point materials must be used at range. Consequently, changes in the structure
temperatures above 1000 ⬚C to achieve an ac- and the mechanical properties do not occur,
ceptable tool life. The technically interesting even with prolonged high-temperature loading.
metals in this family include materials based on The creep properties of these materials are sig-
alloys of the body-centered cubic molybdenum nificantly better than other hot working mate-
with a liquidus of 2620 ⬚C. No lattice transfor- rials, as seen in Fig. 7.131. Molybdenum alloys
mations occur on heating, and consequently, are used in the work-hardened state. The initial
molybdenum-base alloys can withstand tem- strength depends on the deformation from roll-
peratures up to 1500 ⬚C. According to Table ing or forging and from the extent of the car-
7.13, the thermal expansion is lower than all bide dispersion. The most common molybde-
other hot working materials for extrusion dies. num alloy is the hot working material TZM.
More recently, the more highly alloyed grades
This complicates the shrink-fitting of die inserts
ZHM and MHC have become available. Com-
into die holders. The thermal conductivity of pared to TZM, these hot working materials
this material is higher. have even better hot strength and creep prop-
Its resistance to high temperatures can be in- erties. Molybdenum alloys can give much bet-
creased with the aid of suitable alloying ele- ter throughputs than forged cobalt alloys under
ments by raising the recrystallization tempera- high thermomechanical loads [Kor 97]. Extru-
ture with particle hardening. Molybdenum sion dies made of TZM have been used with
alloys with small additions of titanium, zirco- high throughputs for the extrusion of iron alloys
nium, and hafnium have significant hot but have not prevailed [Bra 66].
strengths at extrusion temperatures over 1000
⬚C, in contrast to the usual hot working steels 7.15.3 Nickel Alloys
and cobalt- and nickel-base alloys, as clearly The formation of face-centered cubic solid
shown by the tool material TZM in Fig. 7.130. solutions give high-temperature nickel alloys
Fig. 7.130 Mechanical properties of the hot working materials in Table 7.13 as a function of different working temperatures
from literature data [Schi 82]
Chapter 7: Extrusion Tooling / 541
550° C
1.2567
280 N/mm2
10
1.2343
650° C
2.4969 (Nimo-
nic 90) 284 N/mm2
980° C
Mo alloy: Ti = 0.5%;
Enlongation, %
1 Mo = bal
315 N/mm2
550° C
0.1
0.01
1 10 102 103 104 105
Time, h
Fig. 7.131 Creep expansion of different hot working materials as a function of the load, temperature, and working time of
extrusion tools [Bra 66]
higher recovery and recrystallization tempera- the trade name Cermotherm 2015 is listed. This
tures and thus good high-temperature mechan- is a composite material produced by powder
ical properties compared to the body-centered metallurgy with a molybdenum metal matrix
cubic hot working steels. Precipitates of inter- and embedded zirconium oxide particles. The
metallic phases can be produced by the addition hot working material is very brittle and there-
of chromium, cobalt, molybdenum, aluminum, fore requires shrink-fitting before use. It has
titanium, and so on, giving a further increase in proved very successful for the extrusion of
the hot strength. The creep strength of nickel brasses, particularly those containing lead. In
alloys is improved by precipitates of the c- the extrusion of these alloys, dies with Cer-
phase Ni3 (Ti, Al). Increasing amounts of al- motherm inserts can give throughputs 1.5 to 3.5
loying elements, which form the face-centered times that of stellite inserts. However, the high
cubic phases, increase the hot strength of nickel notch sensitivity of metal-ceramic materials en-
alloys in proportion to their weight content. The sures that Cermotherm inserts are more suited
nickel alloy 2.4668 is solution heat treated be- for the extrusion of rod with simple cross sec-
tween 960 and 980 ⬚C, cooled in forced air, and tions, including squares and rectangles. Com-
age hardened at 700 to 730 ⬚C, with furnace plicated sections are best produced with stellite
cooling to 610 to 630 ⬚C for 8 h holding time, die inserts. The material is very sensitive to
followed by cooling in air to produce fine pre- shocks, and this must be taken into account in
cipitates of the c-phase. The precipitation hard- machining and also during extrusion. Its brittle
ening produces a significant increase in the hot nature limits the applications. It attains the
strength as well as the creep strength, so that maximum hot strength at approximately 600
high-temperature nickel alloys are able to with- ⬚C, and the hot strength is higher than its
stand deformation temperatures up to 1200 ⬚C strength at room temperature, even at tempera-
for short periods. These operating conditions tures of approximately 1200 ⬚C. It is therefore
occur in dies for the extrusion of copper and suitable for the extrusion of materials in the
titanium alloys [Kor 97, Elm 89]. temperature range between 600 and 1000 ⬚C.
Because the metal-ceramic materials have no
7.15.4 Metal-Ceramic tendency to weld to the extruded material, ex-
cellent surface finishes on the extrusion can be
Composite Materials
achieved. In addition, the thermal conductivity
In the molybdenum alloys in Table 7.13, the is relatively high compared to other materials,
composition of a metal-ceramic material with although its thermal expansion is low. This
542 / Extrusion, Second Edition
must be taken into account during shrink-fitting nesium oxide to reduce the sensitivity to ther-
of die inserts. mal shock. Their basic chemical composition
can be found in Table 7.13. The grain of the
material must be fine to achieve a high density
7.15.5 Hard Metals
of the sintered material, and a fine grain ensures
Hard metals consist of metallic hard materi- a good surface finish on the extrusion. Coarser
als, usually carbide based. They are produced grain can be pulled out of the working surfaces
by powder metallurgy using sintering pro- of the die by the flow of the extruded material,
cesses. High-wear-resistant materials can be which damages the surfaces of the extruded
produced in this way. The focus for the use of product.
hard metal inserts is their application as a ma- The successful application of extrusion dies
terial for the production of tools for volume and die inserts in aluminum oxide (Al2O3) ce-
production. Die inserts are used, for example, ramics for the manufacture of wire in copper,
for the production of round wire from copper copper alloys, and aluminum alloys has been
alloys, solder wire in lead and tin alloys, and described in the literature. A significantly
extruded tubes in aluminum alloys. Cobalt-al- longer die life and better surface finish of the
loyed hard metals based on titanium carbide are semifinished product can be achieved compared
particularly suitable. Hard metals have a low to dies in tungsten-alloyed hot working steels.
toughness and therefore must be compressed in For example, in the extrusion of aluminum con-
the die body by shrink-fitting. Because these ductor wires with extrusion dies in conventional
materials also have a low thermal expansion, hot-working steel, the wire surface progres-
they must be particularly highly prestressed in sively deteriorates after approximately 1000 m
the shrink-fitting [Rei 82, Kol 91, Kor 97]. extruded length. However, with Al2O3 die in-
serts, a die life from 30 to 110 km with a con-
7.15.6 Pure Ceramic stant high-quality wire surface can be achieved,
depending on the wire dimensions.
Hot Working Materials
In general, ceramic materials can only be
In addition to metal-based special materials, prepared with diamond grinding discs and
pure ceramic materials of zirconium oxide and lapped with diamond paste. Consequently, die
aluminum oxide have proved successful for ex- inserts must be manufactured as closely as pos-
trusion at high temperatures well above 1000 sible to the finished shape by compaction and
⬚C. Ceramic materials are characterized by an sintering [Dör 82, Kor 97].
extremely low surface-wetting capability.
Therefore, materials extruded with them have
good surface finishes. Ceramic materials, unlike 7.16 Further Developments
metals, do not have any slip planes. Stress con-
centrations in ceramic materials cannot be re- The wide range of very different hot working
duced by localized slip. Instead, spontaneous materials used for the manufacture of extrusion
brittle fracture occurs when the fracture tooling demonstrates the continuous endeavors
strength is exceeded. Oxide ceramics can only of extrusion and tooling experts to find even
be used successfully as compressively pre- more efficient tool materials. It is recognized
stressed, that is, shrink-fitted, die inserts. The that the hot working materials needed for the
materials also have a low thermal expansion, manufacture of extrusion tooling must have suf-
which must be taken into account during the ficient creep/fatigue properties to withstand the
shrink-fitting of ceramic die inserts. On the load cycles in production. If the temperatures
other hand, they are dimensionally very stable fall in the range of crystal recovery of the spe-
at high operating temperatures as a result of the cific hot working material, then creep will occur
low thermal expansion. under mechanical loading. The creep strength
Zirconium oxide ceramic is primarily suit- is therefore much more a decisive factor than
able for the extrusion of copper alloys and, in the 0.2% hot proof stress and the hot tensile
particular, of brasses, including CuZn37 and stress for hot working materials subjected to
CuZn39Pb3, as well as for the extrusion of high thermomechanical loads [Kor 97]. Figure
graphite and austenitic steels. Zirconium-base 7.131 compares the temperature- and time-de-
hot working materials are sintered at approxi- pendent creep strain of some of the hot working
mately 1700 ⬚C. They are stabilized with mag- materials used today.
Chapter 7: Extrusion Tooling / 543
Work is being carried out on the powder met- cluding the container liner and the dummy
allurgy production of hot working steels to in- block. Depending on the material being ex-
crease tempering resistance, in particular [Sei truded, these tools are thermomechanically
88]. In addition, there is research into increas- highly loaded, whereas the tools with no con-
ing the hot toughness by alloy optimization of tact with the extruded material are not subjected
the more highly alloyed hot working steels, for to the same temperatures but can still be me-
example, those in the fourth group in Table chanically highly loaded. The cross section of
7.15, so that they can be used for large alumi- a direct tube press in Fig 7.132 gives an over-
num hollow dies. Further developments in view of this.
CVD coatings are expected in the surface treat- The selection of the suitable hot working ma-
ment of extrusion tooling for the hot working terial for the manufacture of the extrusion tool
of aluminum alloys, although the coating con- depends on these stresses. Every hot working
ditions are difficult. The high coating tempera- material has its own individual hot strength
tures of approximately 1000 ⬚C require a me- range in which the important parameters for hot
chanically finished die for coating that can be working, including the hot proof stress, hot
heat treated after the surface treatment. strength, hot fatigue strength, creep strength,
hot toughness, and hot wear resistance, have a
balanced relationship to each other. This bal-
7.17 Hot Working Materials for ance must be taken into account, particularly
with hollow dies for aluminum alloys, in order
Different Extruded Materials for to avoid premature die failures. The alloy steel
the Manufacture plants provide relevant data and guidelines in
of Extrusion Tooling for their material brochures. The steel application
Direct and Indirect Forming lists 201 and 202 also help with data on the hot
strength, hot toughness, creep strength, and hot
In section 7.1.1, the extrusion tooling is clas- elongation for the hot working materials cur-
sified into those for direct external and internal rently used. This does not, however, exclude
shape production, for example, extrusion dies the specific experience accumulated within an
and mandrels, and those for indirect shape pro- extrusion plant for types of tooling and the ma-
duction as well as auxiliary and support tooling. terial extruded with them, which adds to the
Extrusion tooling for direct shape production data from the supplier. This results in specific
comes into direct contact with the extruded ma- demands from the user as, for example, written
terial during the extrusion process, as do some down in the technical supply guidelines of the
of the tooling for indirect shape production, in- DGM for hot working materials for the manu-
Fig. 7.132 Complete tool set of a direct rod and tube extrusion press with internal piercer as well as liquid-cooled tapered
mandrel. The terminology corresponds to DIN 24540. Source: Sauer
Table 7.16 Hot working materials for direct deformation extrusion tooling
544 / Extrusion, Second Edition
Extruded material
Lead-zinc and tin alloys Magnesium and aluminum alloys Copper alloys Iron alloys
Extrusion tools Tool material Tool material Initial strength, N/mm2 Tool material Initial strength, N/mm2 Tool material
Extrusion dies 1.2343 1.2343/1.2367 1500–1800 1.2365/1.2888/1.2889 1450–1550 1.2343/1.2731 (forged or cast)
Stellite 3/stellite 6 1.2731 ⬃1050
(for solder wires) 2.4668 1300–1400
Feeder chambers 1.2323/1.2343 1.2343 1500–1700 Not suitable ... Not suitable
Die inserts Not common In general, not common ... Cermotherm (brass wire) 1200–1500 TZM
MHC/ZrO2 (German silver)
2.4668/2.4973/2.4979
Stellite 3/stellite 6
Die body Not common In general, not common ... 1.2343/1.2367/1.2889 1450–1550 1.2343
1.2731 ⬃1200
Mandrel 1.2343 ⬍60 mm diameter, 1.2367 ⬍60 mm diameter, 1600–1800 ⬍60 mm diameter, 1.2367 ⬍60 mm diameter, 1600–1700 1.2344/1.2367
⬎60 mm diameter, 1.2343 ⬎60 mm diameter, 1500–1600 ⬎60 mm diameter, 1.2343/1.2367 ⬍60 mm diameter, 1500–1600
Mandrel tips Not common 1.2343/1.2367 1600–1800 1.2889 1400–1500 Not common
2.4973/2.4979 1200–1500
Porthole dies 1.2343 1.2343/1.2367 1500–1800 Not suitable ... Not suitable
1.2885
Bridge dies 1.2343 1.2343/1.2367 1500–1800 2.4668/2.4973 1200–1500 Not suitable
1.2885
Table 7.17 Hot working materials for indirect deformation extrusion tooling
Also for auxiliary and support tooling
Extruded material
Lead-zinc and tin alloys Magnesium and aluminum alloys Copper alloys Iron alloys
Extrusion tools Tool material Tool material Initial strength, N/mm2 Tool material Initial strength, N/mm2 Tool material
Backer 1.2343 1.2343 1400–1500 1.2343/1.2714 1300–1500 1.2343
Bolster 1.2343/1.2714 1.2343/1.2714 1400–1500 1.2343/1.2714 1300–1500 1.2343/1.2714
Subbolster 1.2714 1.2714 1400–1500 1.2343/1.2714 1300–1500 1.2343/1.2714
Pressure plate in extrusion press platen 1.2714 1.2714 1400–1500 1.2714 1200–1300 1.2714
Die holder 1.2343 1.2343 1400–1500 1.2343/1.2365 1400–1500 1.2343/1.2367
1.2367/1.2885
Tool holder 1.2343 1.2343 1400–1500 1.2343/1.2367 1400–1500 1.2343
Container mantle 1.2343 1.2343 1100–1200 1.234/1.2367 1100–1200 1.2343/1.2367
Container liner holder 1.2343 1.2343 1300–1400 1.2343/1.2367 1300–1400 1.2343/1.2367
Container liner 1.2343 1.2343/1.2367 1400–1500 1.2343/1.2367 1400–1500 1.2343/1.2367
1.2779 1000–1100
Extrusion stem 1.2343 ⬍700 N/mm2, 1.2343 ⬍700 N/mm2, 1500–1600 ⬍700 N/mm2, 1.2367 ⬍700 N/mm2, 1500–1600 1.2343/1.2367
⬎700 N/mm2, 1.2343/1.2367 ⬎700 N/mm2, 1600–1700 ⬎700 N/mm2, 1.2367 ⬎700 N/mm2, 1600–1700
Dummy blocks 1.2343 1.2343/1.2367 (fixed dummy block) 1500–1600 1.2343/1.2367 1500–1700 1.2344/1.2367
2.4668 1300–1500
Cleaning blocks Not necessary 1.2343 1400–1500 1.2343/1.2367 1400–1500 Not necessary
Mandrel holder 1.2343/1.2714 1.2343/1.2714 1250–1350 1.2343/1.2714 1250–1350 1.2343/1.2714
Mandrel bars 1.2343/1.2714 1.2343/1.2714 1250–1350 1.2343/1.2714 1250–1350 1.2343/1.2714
Source: Sayer
Chapter 7: Extrusion Tooling / 545
546 / Extrusion, Second Edition
facture of extrusion tooling for hot working alu- Extrusion of Aluminum), Part 1, Aluminium,
minum alloys [DGM 97]. In individual cases, Vol 59 (No. 9), 1983, p 665–669; Part 2, Al-
the tool-specific requirements can even exceed uminium, Vol 59 (No.10), 1983, p 745–750
these. Tables 7.16 and 7.17 give a general over- [Ake 85]: R. Akeret, Einfluß des Neigungswin-
view of the hot working materials available to- kels und der Länge der Lauffläche auf die
day for the manufacture of extrusion tooling for Reibung im Preßkanal (Influence of the In-
the processing of metallic materials. clination Angle and the Bearing Length on
Table 7.18 illustrates the extent to which an the Friction in the Aperture), Aluminium, Vol
extrusion plant and also the experienced tool 61 (No. 3), 1985, p 169–172
manufacturer must proceed in the selection of [Ame 71]: A. Ames, I. Bielen, and G. Sauer,
the correct hot working material for the manu- Vorschlag zur Normung von Werkzeugen für
facture of an efficient extrusion tool according Leichtmetall-Strangpressen in Abhängigkeit
to the material-specific processing conditions. der Preßkräfte (Proposal for Standardization
of Tools for Aluminum Extrusion as a Func-
REFERENCES tion of the Press Power), Z. Metallkde., Vol
62 (No. 10), 1971, p 716–720.
[Ake 83]: R. Akeret, Einfluß der Querschnitts- [Bar 81]: G. Barten, Einflüsse auf Festigkeit
form und der Werkzeuggestaltung beim und Zähigkeit von härtbaren Warmarbeitss-
Strangpressen von Aluminium (Influence of tählen (Influences on the Strength and
the Cross-Section and the Tool Design in the Toughness on Heat-Treatable Hot-Working
Chapter 7: Extrusion Tooling / 547
Steels), ZWF, Vol 76 (No. 2), 1981, p 89– [Det 89]: D. Deterding, Gebräuchliche War-
100 marbeitsstähle zum Einsatz für Druck-
[Ber 76/1]: H. Berns, Ursachen des Zeitstand- gießformen mit besonderem Hinweis auf den
verhaltens von Warmarbeitsstählen und Ver- Warmarbeitsstahl 1.2367 (Conventional Hot-
gleich von hochwarmfesten Legierungen Working Steels for Use in Pressure Die Cast-
(Causes for the Creep Properties of Hot- ing Molds with Specific Reference to the
Working Steels and Comparison of High Hot-Working Steel 1.2367), Giesserei, Vol 76
Temperature Alloys), ZWF, Vol 71 (No. 5), (No. 24), 1989, p 848–849
1976, p 212–217 [Dez 71]: P. Détrez and M.Th. Leger, Fonderie,
[Ber 76/2]: H. Berns, Auslegung von Block- Vol 26, 1971, p 395–403
aufnehmern und Druckgußkammern unter [DGM 97]: DGM, Technische Lieferrichtli-
Berücksichtigung des Kriechens (Design of nien—Warmarbeitswerkstoffe zum Bau von
Containers and Pressure Casting Chambers Strangpreßwerkzeugen für die Warmumfor-
Taking Creep into Account), ZWF, Vol 71 mung von Aluminium-Werkstoffen (Techni-
(No. 12), 1976 cal Supply Guidelines—Hot-Working Mate-
[Ber 76/3]: H. Berns, Werkstofftechnische Be- rials for the Manufacture of Extrusion
trachtung zur Auslegung von Blockaufneh- Tooling for the Hot-Working of Aluminum
mern für das indirekte Strangpressen von Materials), Dtsch. Ges. Materialkd. March
Messing (Material Scientific Considerations 1997
in the Design of Container for the Indirect [Dör 82]: E. Dörre, “Keramische Werzeug-
Extrusion of Brass), Z. Metallkde., Vol 67 werkstoffe” (“Ceramic Tool Materials”),
(No. 5), 1976 VDI-Report 439, 1982, p 61–67
[Ber 76/4]: H. Berns, Zeitstanduntersuchungen [Dub 86]: Dubbel, 15th ed., p 198, 219–220,
an Warmarbeitsstählen (Creep Studies on 228
Hot-Working Steels), ZWF, Vol 71 (No. 2), [Eck 97]: W. Eckenbach, Werkzeuge für das
1976, p 64–69 Strangpressen, Neuere Entwicklungen der
[Ber 82]: H. Berns, “Warmarbeitsstähle und— Widerstandsheizungen von Rezipienten
legierungen” (“Hot-Working Steels and Al- (Tools for Extrusion, New Developments in
loys”), VDI-Report 432, 1982, p 43–49 the Resistance Heating of Containers), Alu-
[Bra 66]: H. Braun and W. Schulte, Molybdän- minium, Vol 73 (No. 7/8), 1997, p 470–472
matrizen für das Strangpressen von Stahlp- [Elm 89]: E. El-Magd, K.Th. Kaiser, and H.W.
rofilen (Molybdenum Dies for Steel Section Walkendorf, Einfluß der Vorbehandlung auf
Extrusion), Stahl Eisen, Vol 86 (No. 15), die Struktur hochwarmfester Nickellegierun-
1966, p 967–980 gen (Influence of the Pretreatment on the
[Bre 79]: H. Brendel and H. Winkler, Wissen- Structure of High Temperature Nickel Al-
speicher Tribotechnik, Springer Verlag, Ber- loys), Metall., Vol 43 (No. 12), 1989, p
lin, 1979 1149–1152
[Bri 75]: H. Briefs and M. Wolf, Warmarbeits- [Eys 67]: F.W. Eysell, Herstellung und Behan-
stähle (Hot-Working Steels), Verlag Stahle- dlung von Strangpreßwerkzeugen: III Behan-
isen, Düsseldorf, 1975, p 47 dlung von Strangpreßwerkzeugen durch
[Brs 81]: H. Brandis, B. Huchtemann, and A. Salzbadnitrieren (Manufacture and Treatment
Steinen, Technologie der Wärmebehandlung of Extrusion Tools, Part III: Treatment of Ex-
warm-und hochwarmfester Stähle (Technol- trusion Tools by Salt Bath Nitriding), Z. Me-
ogy of the Heat-Treatment of High Tempera- tallkde; Vol 58 (No. 5), 1967, p 285–288
ture and Very High Temperature Steels), [Gah 90]: K.-H. Zum Gahr, Reibung und Ver-
Thyssen Edelstahl Tech. Ber., Vol 7 (No. 1), schleiß bei metallischen und nichtmetal-
1981, p 28–30 lischen Werkstoffen (Friction and Wear in
[Bun 81]: W. Bunk, I. Hansen, and M. Gregor, Metallic and Nonmetallic Materials), DGM-
Tribologie, Band 1 (Tribology, Vol 1), Informationsgesellschaft Verlag, 1990
Springer Verlag, Berlin, 1981 [Gie 95]: Gieck, Technische Formelsammlung
[Cae 77]: A. Caery, Vorgetragen anläßlich des (Technical Collection of Formulae), 30th ed.,
Internationalen Kolloquiums über Warmar- 11–15, 17
beitsstähle am 1 und 2 (Presented at the In- [Gri 82]: W. Grimm, A. Mukhoty, and D.
ternational Colloquium on Hot-Working Roempler, Einfluß verschiedener Schmelz-
Steels on 1 and 2), Dec 1977 (St. Etienne) varianten auf die mechanischen Eigenschaf-
548 / Extrusion, Second Edition
ten von Einsatzstählen (Influence of Different of Conventional Hot-Working Steels and Spe-
Melt Versions on the Mechanical Properties cial Alloys in Extrusion), Sonderheft der
of Case-Hardening Steels), ZWF, vol 77 (No. Schmidt Ⳮ Clemens GmbH Ⳮ Co., 1997
4), 1982, p 194–199 [Kra 89]: R. Kranz, F. Wendl, and K.D. Wup-
[Güm 81]: P. Gümpel and K. Rasche, Entwick- per, Einfluß der Erodierbedingungen auf die
lungsstand bei Warmarbeitsstählen (Devel- Zähigkeit von Werkzeugstählen (Influence of
opment of Hot-Working Steels), Thyssen the Erosion Conditions on the Toughness of
Edelstahl Tech. Ber., Vol 7 (No. 2), 1981, p Tool Steels), Thyssen Edelstahl Tech. Ber.,
151–160 Vol 15 (No. 2), 1989, p 126–131
[Hab 77]: E. Haberling, Zeitstand-und Dauer- [Kre 78]: W. Krebs, Giesserei, Vol 65, 1978, p
festigkeit von Warmarbeitsstählen bei er- 645–652, 733–739
höhten Temperaturen (Creep and Fatigue [Lan 81]: G. Lang, Abschätzung der Reibung
Strength of Hot-Working Steels at Elevated im Preßkanal beim direkten und indirekten
Temperatures), Thyssen Edelstahl Tech. Ber., Strangpressen von Al99.6 (Estimation of the
Vol 3 (No. 2), 1977, p 125–129 Friction in the Die Aperture in Direct and
[Hab 80]: K.-H. Habig, Verschleiß und Härte Indirect Extrusion), Aluminium, Vol 57 (No.
von Werkstoffen (Wear and Hardness of Ma- 12), 1981, p 791–796
terials), Carl Hanser Verlag, München, Wien, [Lan 84]: G. Lang, Reibung im Preßkanal beim
1980 direkten und indirekten Strangpressen (Fric-
[Hab 81]: E. Haberling, Zähigkeitsprüfung von tion in the Die Aperture in Direct and Indi-
Warmarbeitsstählen (Toughness Testing of rect Extrusion) of Al99.6, AlMgSi0.5, and
Hot-Working Tool Steel), Thyssen Edelstahl AlZn4.5Mg1, Aluminium, Vol 60 (No. 4),
Tech. Ber., Vol 7 (No. 2), 1981, p 166–167 1984, p 266–268
[Hab 87]: E. Haberling, Zeitstandfestigkeit von [Lau 76]: K. Laue and H. Stenger, Strangpres-
Warmarbeitsstählen (Creep Strength of Hot- sen, Verfahren—Maschinen—Werkzeuge (Ex-
trusion—Processes—Machining—Tooling),
Working Steels), Thyssen Edelstahl Tech.
Aluminium-Verlag GmbH, 1976, p 293–294
Ber., Vol 13 (No. 2) 1987, p 118–121
[Mit 97]: W. Mitter, K. Haberfellner, R. Dan-
[Har 84]: K.E. Haberfellner and F.M. Schin-
zer, and C. Stickler, Lebensdauerprognose
dler, “State and Development of Tooling Ma-
für Warmarbeitsstähle (Service Life Progno-
terials,” International Aluminum Extrusion sis for Hot-Working Steels), HTM, Vol 52
Technology Seminar (Atlanta, GA), 1984 (No. 4), 1997, Carl Hanser Verlag, München
[Hol 96]: K. Holthe and S. Tjotta, “The Heat [Mül 95]: K. Müller et al., Grundlagen des
Balance during Multiple Press Cycles,” In- Strangpressens (Fundamentals of Extrusion),
ternational Aluminum Extrusion Technology Expert-Verlag, 1995, p 140–168
Seminar, (Chicago, IL), 1996 [Ort 77]: R. Ortmann, Untersuchungen zum
[Hub 80]: U. Huber-Gommann, H.J. Grose- Aushärtungsverhalten des
mann, and G. Schulz, Nitrieren im Ammon- Preßmatrizenstahles (Investigations into the
iakgasstrom (Nitriding in an Ammonia Gas- Age-Hardening Behavior of Extrusion Die
flow), ZWF, Vol 75 (No. 9), 1980, p 407–410 Steels) X50NiCrWV1313, ZWF, Vol 72 (No.
[Kle 86]: M. Kleyer, Moderne Strang- 9), 1977, p 496–498
preßmatrizen (Modern Extrusion Dies), VDI- [Rei 82]: N. Reiter, Hartmetalle als Werkzeug-
Ber., Vol 128 (No. 10), 1986, p 88–93 werkstoff (Hard Metals as Tool Material),
[Kol 91]: H. Kolaske and K. Dreyer, Neuerun- VDI-Ber., No.439, 1982, p 145–158
gen auf dem Hartmetallgebiet (Developments [Sar 67]: G. Sauer, Herstellung und Behan-
in Hard Metals), Ing. Werkst., Vol 3 (No. 5), dlung von Strangpreßwerkzeugen IV: Erhö-
1991, p 58–61 hung der Standzeiten von Aluminium-
[Kor 95]: W. Kortmann, Werkzeugwerkstoffe Preßwerkzeugen durch Salzbadnitrieren
für das Strangpressen, Grundlagen des (Manufacture and Treatment of Extrusion
Strangpressens, Kontakt Ⳮ Studium (Tool Tools, IV: Increasing the Service Life of Alu-
Materials for Extrusion, Fundamentals of Ex- minum Dies by Salt Bath Nitriding), Z. Me-
trusion, Contact and Study), Expert-Verlag, tallkde., Vol 58 (No. 5), 1967, p 289–296
1995, p 84–93 [Schi 82]: A. Schindler, G. Fertl, and H.
[Kor 97]: W. Kortmann, Vergleich herkö- Kröhnke, Werkzeugwerkstoffe für das
mmlicher Warmarbeitsstähle zu Sonderlegi- Strangpressen (Extrusion Tool Materials),
erungen im Strangpreßbereich (Comparison VDI-Ber., No.432, 1982, p 91–101
Chapter 7: Extrusion Tooling / 549
CHAPTER 8
The selection of a QMS can, for example, fol- a planned, long-term concept into which the
low QS 9000. The following conditions must be company-specific requirements can be inte-
fulfilled in the selection of the QMS: grated. The goal must be not only to obtain a
certificate of compliance but also to create a
● Complete understanding and implementa- management tool that can be constructively used
tion of the customer’s requirements by the employees and that brings the desired re-
● Reproducible, documented production pa- sults to the organization. In order to develop a
rameters practical and acceptable QMS, the opportunities
● Controlled internal processing, with delega- within ISO 9000 should be used.
tion of responsibilities Modern quality techniques can be readily
● Promotion of employees’ competence to- used as supplementary methods within the 20
ward individual responsibility elements of ISO 9001. This provides the basic
● Further development of the QMS procedures:
● Organizational responsibility
● Economic and competitive production ● Definition of the vision of the quality culture
Of the QMSs, ISO 9000 is the system that most desired
completely fulfills the company’s functions. ● Derivation of the individual strategies for
Most companies in Europe were previously quality management
certified to ISO 9000 through the European Net- ● Co-operation with the individual lines on the
work for Quality System Assessment (EQNet). development of the individual QMS ele-
The important International Organization for ments
Standardization (ISO) standards for quality ● Integration of quality management tasks into
management and quality control are: the lines, for example, testing procedures
and responsibility for quality
● ISO 9000—guidelines for selection and ap- ● Function of quality control from the view-
plication point of control and consultation
● ISO 9001—model for statement on quality ● Installation of a monitoring system for per-
control in production, assembly, and cus- formance control in all areas
tomer service
● ISO 9002—model for statement for quality The documentation for the organizational and
control in production and assembly operational structures required by ISO 9000
● ISO 9003—model for statement for quality should not be a separate handbook for external
control in final inspection use but an operational manual and reference
● ISO 9004—quality management and ele- book for daily use by all employees.
ments of the quality-control system Figure 8.1 shows a structure for quality-con-
trol documentation classified into internal docu-
8.2.2 Introduction of a QMS mentation (quality control using internal data)
and external documentation (in the form of
The introduction of a QMS that covers all the product catalogs, quality-control documenta-
operations of a company must be planned in tion, and brochures). Figure 8.2 shows the path
various development phases. The foundation is
to a quality culture in eight phases:
Catalog
Guidelines (b)
Quality-
control
Product system
Basic operational documentation (c) catalogs
Quality-
control system
Management*
Processes
Quality-conttol
tools
Electronic data
processing
Personnel*
Finances
Other
documentation Image
The complete process can be divided into pro- The management of interfaces plays a very
cess steps. Interfaces occur at the transitions be- important role in achieving short transit times
tween the process steps. and defect-free production processes. However,
Vision of a quality
culture
Phases
Continuous
improvement
throughout the
8 organization
Fig. 8.3 Complete process chain for order processing within the quality circle [Egg 87]
Chapter 8: Quality Management in Extrusion / 555
the initial approach should be to reduce the num- producer (extrusion plant) must be considered,
ber of interfaces. because a semifinished product producer is not
Examples for low-interface team organiza- usually responsible for either the design or the
tions in an extrusion plant include the following. manufacture of a component or even for the as-
Order Processing. For a specific semi- sembly and direct distribution of end products,
finished product, cooperation between the per- including plant, machinery, and so forth.
sonnel in purchasing, process planning, produc- It is important that the customer order is
tion, and transport is realized in a centralized clearly defined with supplementary information,
order-processing department with an office close including drawings, technical specifications,
to the production. relevant standards, information on required val-
Casting House. Casting teams are formed ues in terms of the chemical composition, me-
that are responsible for the weekly detailed plan- chanical properties, shape, and positional toler-
ning, covering the charging of the melting fur- ances, as well as the required surface condition.
nace, casting and charge testing (analysis, ultra- Component-critical characteristics should be
sonic testing), and homogenizing of the logs up provided in the specification or on the drawing.
to cutting of the extrusion billets. Quality agreements currently represent a stan-
Extrusion. Weekly detailed planning meet- dard binding agreement at the interface between
ings by the press crew establish individual con- supplier and customer. The agreements control
trols testing of the quality characteristics (e.g., product-specific requirements in detail, includ-
shape, roughness, surface quality, weld quality) ing, for example:
during contract processing, up to the point of ● Extent of supply
section packing. Regular monitoring of internal ● Testing responsibility
customer requirements by communication with ● Documentation
internal customers prevents unnecessary addi- ● Liability limitation
tional actions. ● Lot size
● Delivery requirements
8.2.4 Product Liability
● Collaboration on testing and product plan-
With the introduction of the German product ning
liability law on January 1, 1990, the European ● Quality-control system requirements
Union’s rules on product liability for the protec- ● Procedure for technical process variations
tion of the user were extensively extended. In ● Auditing
this law, the change from negligence liability to ● Additional requirements
no-fault causal liability came into effect. The
damage associated with product defect estab- The contract review within the extrusion plant
lishes the causal liability of the producer. The must clarify the technical feasibility. In the case
customer no longer must prove the responsibil- of foreseeable deviations as well as technical
ity of the producer, but the manufacturer has to process limitations, a corresponding written
provide evidence that all measures were taken counterproposal or a cancellation must be sub-
during processing in order to exclude any defect. mitted to the customer (this applies in particular
The product liability demands from all plants to the aircraft and automobile industries). Ref-
and manufacturers involved with a product, even erences to limitations (mechanical properties,
if only for a short time, the organizational pro- analysis variations, charge variations, strength-
cedures in the areas of quality control, product reducing inclusions, residual internal stresses)
documentation, and risk management, from should be specified in writing.
planning to transfer to the customer. The current The order-conforming processing of the cus-
levels of science and technology are applicable. tomer order is the controlling requirement. Man-
The product liability law applies in the case ufacturers can only be relieved from their prod-
of damage to a third party, not between the two uct liability in very specifically defined cases,
contractual partners. The no-fault liability of the depending on the applicable law (in Germany,
manufacturer expires after 10 years (forfeiture), according to the product liability law). The bur-
calculated from the point in time at which the den of proof rests with them. The following ap-
product that caused the failure had been brought plication possibilities must be taken into ac-
into circulation. count:
Above all, the relationship between the con- ● The supplier has not sold the finished prod-
tractor (customer) and the semifinished product uct and is only a subcontractor.
556 / Extrusion, Second Edition
● The supplier has demonstrably not made any The indemnification liability cannot be excluded
errors up to the point of sale. In addition, the by written references in the context of the gen-
defect was not detectable according to the eral commercial and supply terms and condi-
current state of science and technology. tions or by warnings.
● The product corresponds to a national stan- The German product liability law of 1990 §
dard; it must refer to a law or a binding de- 19 concedes the objection to the development
tailed regulation for the manufacture. Stan- risk (§ 1 Par. 2 No. 5) and stipulates an upper
dards including ISO, DIN, or European liability limit of 160 million Deutsche marks for
Standards (EN) have only a limited legal personal injury.
quality, because the user has the option of
selecting deviations with equal or higher 8.2.5 Economics
standards. The fulfillment of these standards The introduction of a QMS is associated with
can only be considered as the minimum re- different costs, depending on the size of the
quirements. company and the level of development. In ad-
● There is no liability for the so-called devel- dition to the one-off introduction costs, there is
opment risks present that existed at the time ongoing expenditure referred to as quality costs.
of bringing to the market but could not be Figure 8.4 shows the division of quality costs
identified by the state of technology and sci- into quality cost groups and quality cost ele-
ence at the time. The controlling point of the ments.
assessment is the time of bringing to the mar-
ket and not of production.
● If it can be proved that the defect results from
8.3 Quality Control
the design of the component into which the
semifinished product was fitted (damage dur-
ing installation or during the operational life) 8.3.1 Organization
as well as by the operational instructions of In a functionally structured large organiza-
the end producer, then this relieves the re- tion, the quality-assurance quality-control (QC)
sponsibility. department is an independent department rep-
Quality costs
resented on the management board (Fig. 8.5). In The QC can be further divided according to
smaller companies, it forms part of the produc- the following plan:
tion department. Integration into departments is
● With extensive delegation of quality testing
also possible.
to the production areas, the QC can be re-
According to the requirements of the quality
duced to technical support.
system standards, the preference is for the QC
● The quality technology could then be ex-
to have a largely independent position within the
tended into the area of quality promotion by
company structure. Apart from the fundamental
training the inspectors in the work place
considerations of the tasks that are centralized
(self-inspection).
and those that are decentralized, decisions must
● The QC can then be considered more as an
also be made on which tasks are to be delegated,
advisory department with the minimum
for example, to the production personnel. It
number of personnel.
should be clarified from the outset whether the
personnel involved report directly to the QC de-
partment or have only a technical supporting 8.3.1.1 Process Organization
role. In the context of a quality system, numerous
The most effective and economic organiza- processes occur with different degrees of im-
tion structure depends on the circumstances spe- portance, including:
cific to the organization:
● Contract review
● Company divisions that must be included, ● Testing plan
for example, development, production, pro- ● Development projects
curement, training, process technology, and ● First-sample test
so on ● Incoming goods inspection
● Range of responsibilities of the QC, for ex- ● Traceability
ample, testing, training, advice ● Documentation
● Present/future organization structure ● Modifications
● Size of the organization ● Monitoring of measurement equipment
● Product mix referred to the safety risks ● Certification
● Fulfillment of the system standards ● Complaints
Quality control
Quality
Production inspection
laboratory
Final inspection
The operational processes described run Organizations with a higher realization degree
throughout the entire company across the func- of TQM are increasingly involved with system-
tional organization. Many of these processes related responsibilities, including maintenance
have the function of a quality-control loop. Fig- and further development of a QMS, promotion
ure 8.6 shows an example of a quality-control of the TQM philosophy, and motivation of em-
loop in production. ployees.
In addition to the knowledge of quality con-
8.3.2 Responsibilities trol and production and information technology,
the social-competence ability in combination
8.3.2.1 General Requirements with team capability and coaching are moving
into the foreground.
In recent years, quality control has developed New areas, including environmental manage-
from a piece-related testing station to a com- ment, will be integrated into a QMS in the future
pany-wide QMS. The personnel of the quality and will then form part of the responsibilities of
department have been continually confronted a quality manager.
with task extensions. Pure, factual knowledge
for the solution of the problems of individual
components no longer suffices. The manage- 8.3.3 Audits
ment of a quality department in a company pro-
ducing semifinished products requires knowl- Auditing need not be used only as a method
edge of the fundamentals of materials science for analyzing the application of quality systems
and deformation technology as well as destruc- but can be extended to an organization-wide
tive and nondestructive materials testing. In ad- management instrument. Audits provide a
dition, it is necessary to have experience in method for the systematic monitoring of the re-
organizational queries, project management, quired-versus-actual state at various levels (Fig.
company strategy, personnel development, 8.8).
methods for process improvement, and general The monitoring of the QMS provides infor-
financial procedures, particularly when an or- mation on product quality, employee qualifica-
ganization intends to work toward total quality tion, as well as logistical quality characteristics
management (TQM) via system certification including delivery times, on-time deliveries,
(Fig. 8.7). flexibility to changes and increases in capacity,
The quality-related strategic knowledge is in- reaction to customer complaints, and interdisci-
creasing compared to the production-related plinary cooperation.
knowledge. Questions such as “Can quality con- Auditing then develops into an instrument for
trol provide an effective risk management cov- strategic control. The QC plans the audit, moni-
ering product liability?” require extensive ex- tors its periodic execution to plan, and prepares
perience. an annual report on the results and actions.
Analyze
procedures
No
Testing planning
Test plan
On one hand, the integration of the line man- methods flow from innovative departments into
agers as trained auditors is supported by the in- other areas. The total knowledge increases. Spe-
creased demand for internal/external customer cific knowledge is available throughout the en-
orientation and, on the other, is upheld by the tire organization by knowledge transfer.
ongoing improvement process. In addition, the
responsibility for quality management has wider 8.3.3.1 QMS Audit
support (Table 8.3). A QMS audit is intended to determine the ef-
The individual departmental and reciprocal fectiveness of the QMS throughout the process-
auditing of different organizational units can be ing of an order/organization. The system audit
carried out by the line managers. A control sys- is an independent test of the quality system of
tem then develops from the continuous-im- an organization or organizational unit, with spe-
provement process throughout the entire orga- cific focus on the interfaces. The weaknesses
nization. This further develops the competence identified are listed in a report that acts as a basis
of the employees involved. The emphasis is on for those responsible to establish and introduce
both self-inspection of the quality and also the the necessary corrective actions.
time-cost parameters. Planning and control re- This type of audit is required by ISO 9000,
sponsibilities are the focal point of this audit and for example. The 20 sections of this standard are
not the “supervision.” accordingly examined. The auditor first ac-
Considered in its entirety, the following bene- quaints himself with the prescribed quality re-
fits can be achieved. Regular internal and exter- quirements (handbooks, procedures, customer
nal auditing produces a measurable statement of requirements, specifications, goals, etc.). The ac-
tual state of the quality system is examined for:
the ongoing improvement process. The recip-
rocal comprehension associated with an im- ● Completeness
proved information exchange is a positive side ● Suitability
effect of interdisciplinary audits. New ideas and
Table 8.3 Audit classification and auditors
QM, quality management; UM, environmental management
Procedures Level Type of audit Auditors
TQM Complete QM-system audit
organization
Certification External
Internal audits Experienced personnel from
TQM concept all departments
UM-system audit
Quality management Certification External
system ISO 9001 Internal audits Experienced personnel from
all departments
Quality Departments Process audit
conformance Technical Personnel from the relevant
departments
Quality control Administrative
Cross functional
Product audit Personnel from the quality
department
Time Personnel Self-inspector audit Experienced personnel from
the relevant departments
Fig. 8.7 The way to total quality management (TQM)
Specified/actual
deviation determination
Introduction of Analysis of
improvement measures deviations
Table 8.4 Failure modes and effect analysis for the extrusion process
Step failure Type of defect, mode Effect of defect Root cause of defect Procedures to prevent defect
1 Dimensional variation, cross Scrap Tool defect press conditions Sampling, periodic testing
section
2 Straightness deviation, bend Increased straightening cost, Section guiding Visual inspection,
scrap stretching, straightening
3 Twist Increased straightening cost Tool defect Stretching, straightening
4 Roughness Scrap Tool damage, metal buildup Periodic visual inspection,
on tool cleaning
5 Die lines Scrap Tool damage, metal buildup Periodic visual inspection,
on tool cleaning
6 Graphite bands, flakes Scrap Section guiding (cannot be Cleaning
avoided completely)
7 Mechanical damage Scrap Section guiding, handling ...
8 Pick-up Scrap Billet ...
9 Transverse cracking Scrap ... ...
10 Incorrect billet, incorrect Scrap ... ...
charge
11 Lubricant inclusions ... ... ...
Chapter 8: Quality Management in Extrusion / 561
Drawing
+ parts list
+ product concept catalog
Operational Inspection
Machine sequence
plan plan
Operational planning
+ inspection planning
APPENDIX A
ABillet Billet cross-sectional area FRmax Maximum value of the axial force re-
AStem Stem cross-sectional area quired to overcome the friction be-
A0 Container cross-sectional area tween the billet and the container
AS Section cross-sectional area FSt Stem load
b Heat penetration coefficient FSt max Maximum stem load
bB Heat penetration coefficient for billet FSt min Minimum stem load
material FU Axial deformation load
bR Heat penetration coefficient for con- F̄U Constant deformation load during the
tainer material quasi-stationary deformation process
C Die profile relative load factor FVSt Sealing stem load
c Specific heat capacity F̂VSt Maximum axial load on the sealing
cB Specific heat capacity of the billet ma- stem
terial F̄VSt Constant axial load on the sealing stem
cR Specific heat capacity of the container during the quasi-stationary deforma-
material tion process
DA Die exit diameter kf Flow stress
Da Tube external diameter kf0 Flow stress of the extruded material
DB Initial billet diameter outside the deformation zone
DD Mandrel diameter k̄f Mean flow stress of the extruded ma-
DDS Mandrel holder diameter terial in the deformation zone
Di Tube internal diameter lB Billet length (initial billet length)
lMF Length of the outermost die guiding
DMa Die external diameter
surface
D0 Container diameter
l0 Length of the upset billet in the con-
D*o Equivalent container diameter tainer
DS Extruded bar diameter lR Discard length
D*S Equivalent extruded bar diameter lS Extruded length
FHSt Axial force on the hollow stem lU Length of the deformation zone
F̂HSt Maximum axial force on the hollow p Hydrostatic pressure
stem p̂ Maximum value of the hydrostatic
F̄HSt Constant axial force on the hollow pressure
stem during the quasi-stationary defor- p̄ Constant hydrostatic pressure to be re-
mation process ferred to during the quasi-stationary
FM Axial force on the die deformation process
F̂M Maximum axial force on the die pr Radial compressive stress
F̄M Constant axial force on the die during pSt Specific stem pressure (specific stem
the quasi-stationary deformation pro- pressures referred to the container
cess cross-sectional area)
fp Profile factor p̂St Maximum specific stem pressure
FR Axial force required to overcome the (maximum specific stem pressure re-
friction between the billet and the con- ferred to the container bore cross-sec-
tainer tional area)
566 / Extrusion, Second Edition
APPENDIX B
Approximate Composition of
Materials
Table 1 Approximate composition of aluminum alloys
Material Similar UNS No. Si Fe Cu Mn Mg Cr Zn Other Al
5182 A95182 0.2 max 0.35 max 0.15 max 0.5 max 4.0–5.0 0.1 max 0.25 max 0.1 Ti max; others 0.05 each, total 0.15 max ...
6009 A96009 0.6–1.0 0.50 max 0.15–0.6 0.20–0.8 0.40–0.8 0.10 max 0.25 max 0.10 Ti max; others 0.05 each, total 0.15 max ...
6016 A96016 1–1.5 0.5 max 0.2 max 0.2 max 0.25–0.6 0.1 max 0.2 max 0.15 Ti max; others 0.05 each, total 0.15 max ...
AA6013 A96013 0.6–1.0 0.5 max 0.6–1.1 0.20–0.8 0.8–1.2 0.1 max 0.25 max 0.10 Ti max; others 0.05 max each, total 0.15 max bal
AA6056 A96056 0.7–1.3 0.5 max 0.50–1.1 0.40–1.0 0.6–1.2 0.25 max 0.10–0.7 (Ti Ⳮ Zr) 0.20 max; others 0.05 max each, total bal
0.15 max
AA6113 reinforced A96113 0.6–1.0 0.30 max 0.6–1.1 0.10–0.6 0.8–1.2 0.10 max 0.25 max 0.10 Ti max, 0.05–0.50 O; others 0.05 max each, bal
with 25% SiC others total 0.15 max. Note: reinforced with
25% SiC
AA8090 A98090 0.20 max 0.30 max 1.0–1.6 0.10 max 0.6–1.3 0.10 max 0.25 max 2.2–2.7 Li, 0.10 Ti max, 0.04–0.16 Zr; others 0.05 bal
max each, others total 0.15 max
Al99 A91200 ... ... 0.05 max 0.05 ... ... 0.1 max Fe Ⳮ Si 1.00 max, 0.05 Ti max bal
568 / Extrusion, Second Edition
Al99.5 A91050 0.25 max 0.4 max 0.05 max 0.05 max 0.05 max ... 0.07 max Cu Ⳮ Fe Ⳮ Si Ⳮ Zn 0.50 max; others 0.03 max bal
each
Al99.6 A91060 0.25 max 0.35 max 0.05 max 0.03 max 0.03 max ... 0.05 max 0.03 Ti max; others 0.03 max each bal
Al99.8 A91085 0.15 max 0.15 max 0.03 max 0.02 max 0.02 max ... 0.06 max Cu Ⳮ Fe Ⳮ Si Ⳮ Zn 0.20 max; others 0.03 max bal
each
Al99.85 A91085 0.05 max 0.07 0.01 max 0.02 max 0.01 max 0.02 0.02 max 0.03 Ga max; others total 0.01 max bal
Al99.98 A91098 0.010 max 0.006 max 0.003 max ... ... ... 0.010 max 0.003 Ti max; others 0.003 max each bal
Al99.98R A91098 0.010 max 0.006 max 0.003 max ... ... ... 0.01 max 0.003 Ti max; others 0.003 max each bal
Al99Cu A91100 ... ... 0.05–0.20 0.05 ... ... 0.1 Si Ⳮ Fe 0.95 max bal
AlCu2LiMg1.5 A92061 0.20 max 0.30 max 1.8–2.5 0.10 max 1.1–1.9 0.10 max 0.25 max 1.7–2.3 Li, 0.10 Ti max, 0.04–0.16 Zr max; others bal
0.05 max each, others total 0.15 max
AlCu2Mg1.5Ni A92618 0.1–0.25 0.9–1.3 1.9–2.7 ... 1.3–1.8 ... 0.1 max 0.9–1.2 Ni, 0.04–0.1 Ti; others 0.05 max each, bal
others total 0.05 max
AlCu4Mg1 A92024 0.5 0.5 3.8–4.9 0.3–1.2 1–1.8 ... 0.2 0.2 Ni bal
AlCu4PbMgMn A92007 0.8 max 0.8 max 3.3–4.6 0.50–1.0 0.40–1.8 0.10 max 0.8 max 0.20 Bi max, 0.20 Ni max, 0.8–1.5 Pb max, 0.20 bal
Sn max, 0.20 Ti max; others 0.10 max each,
others total 0.30 max
AlCu4SiMg A92014 0.5–1.2 0.7 3.8–5 0.3–1.2 0.2–0.8 ... 0.2 0.2 Ni bal
AlCuBiPb A92011 0.40 max 0.7 max 5.0–6.0 ... ... ... 0.30 max 0.2–0.6 Bi, 0.20–0.6 Pb; others 0.05 max each, bal
others total 0.15 max
AlCuMg1 A92017 0.20–0.8 0.7 max 3.5–4.5 0.40–1.0 0.40–1.0 0.10 max 0.25 max Ti Ⳮ Zr 0.25 max; others 0.05 max each, others bal
total 0.15 max
AlCuMg2 A92024 0.50 max 0.50 max 3.8–4.9 0.30–0.9 1.2–1.8 0.10 max 0.25 max 0.15 Ti max; others 0.05 each, others total 0.15 bal
max
AlCuMgPb A92007 0.8 max 0.8 max 3.3–4.6 0.10 max 0.40–1.8 0.10 max 0.8 max 0.20 Bi max, 0.2 Ni max, 0.8–1.5 Pb, 0.20 Sn bal
max, 0.20 Ti max; others 0.10 max each, others
total 0.30 max
AlCuSiMn A92014 0.50–1.2 0.7 max 3.9–5.0 0.40–1.2 0.20–0.8 0.10 max 0.25 max 0.15 Ti max; others 0.05 each, others total 0.15 bal
max
AlFeSi A98011 0.4–0.8 0.5–1.0 0.10 max 0.10 max ... ... 0.10 max 0.05 Ti max; others 0.06 max each, others total bal
0.25 max
AlLi2.5Cu1.5Mg1 A98090 0.20 max 0.30 max 1.0–1.6 0.10 max 0.6–1.3 0.10 max 0.25 max 2.2–2.7 Li, 0.10 Ti max, 0.04–0.16 Zr; others 0.05 bal
max each, others total 0.15 max
AlMg1 A95005 0.4 0.7 0.2 0.2 0.5–1.1 0.1 0.2 ... bal
AlMg1.5 A95050 0.4 0.7 0.2 0.3 1.1–1.8 0.1 0.2 ... bal
AlMg1Mn1 A93004 ... ... ... 1.2 1.1 ... ... ... bal
AlMg1SiCu A96061 0.4–0.8 0.7 0.15–0.4 0.15 0.8–1.2 0.04–0.35 0.25 ... bal
AlMg2.5 A95052 0.5 0.5 0.1 0.5 2.2–2.8 0.35 0.2 ... bal
AlMg2.5Cr A95052 ... ... ... ... 2.5 0.25 ... ... bal
AlMg2.7Mn A95454 0.25 max 0.40 max 0.10 max 0.50–1.0 2.4–3.0 0.05–0.20 0.25 max 0.20 Ti max; others 0.05 max each, others total bal
0.15 max
AlMg2.7MnCr A95454 ... ... ... 0.75 2.7 0.12 ... ... bal
AlMg3 A95754 0.5 0.5 0.1 0.5 2.6–3.4 0.35 0.2 ... bal
AlMg3.5Mn A95154 ... ... ... 0.3 3.5 ... ... ... bal
AlMg3Mn A95454 0.5 0.5 0.1 0.3–1 2.4–3.4 0.25 0.2 ... bal
AlMg4.5 A95083 0.5 0.5 0.1 0.3–1 4–4.9 0.25 0.2 ... bal
AlMg4.5Mn A95083 0.5 0.5 0.1 0.3–1 4–4.9 0.25 0.2 ... bal
AlMg4.5Mn A95083 0.5 0.5 0.1 0.3–1 4–4.9 0.25 0.2 ... bal
AlMg4.5Mn0.7 A95083 0.40 max 0.40 max 0.10 max 0.10–1.0 4.0–4.9 0.05–0.25 0.25 max 0.15 Ti max; others 0.05 each, others total 0.15 bal
max
AlMg5 A95056 0.5 0.5 0.1 1 4.5–5.5 0.35 0.2 ... bal
AlMg5Mn A95182 0.20 max 0.35 max 0.15 max 0.20–0.50 4.0–5.0 0.10 max 0.25 max 0.10 Ti max; others 0.05 max each, others total bal
0.15 max
AlMgSi A96063 0.3–0.7 0.5 0.058 max ... 0.4–0.9 0.1 0.2 ... bal
AlMgSi0.5 A96060 0.30–0.6 0.10–0.30 0.10 max 0.10 max 0.35–0.6 0.05 max 0.15 max 0.10 Ti max; others 0.05 each, others total 0.15 bal
max
AlMgSi0.7 A96005 0.50–0.9 0.35 max 0.30 max 0.05 max 0.40–0.7 0.30 max 0.20 max 0.1 Ni max, 0.10 Ti max, 0.12–0.050 (Cr Ⳮ Mn); bal
others 0.05 max each, others total 0.15 max
AlMgSi0.8 A96009 0.8–1 0.25 0.05 0.15 0.6–0.7 0.03 0.1 0.05 Ti; others 0.00 max each, others total 0.15 bal
AlMgSi1 A96181 0.8–1.2 0.5 max 0.1 max 0.2–1.0 0.6–1.0 0.1 max 0.2 max 0.2 Ti max; others 0.05 max each, others total bal
0.15 max
AlMgSi1Cu A96030 0.40–0.8 0.7 max 0.15–0.40 0.15 max 0.8–1.2 0.04–0.35 0.25 max 0.15 Ti max; others 0.05 max each, others total bal
0.15 max
AlMgSiCu A96261 0.4–0.7 0.4 max 0.15–0.40 0.20–0.35 0.7–1.0 0.10 max 0.2 max 0.10 Ti max, Ti includes Zr; others 0.05 max bal
each, others total 0.15 max
AlMgSiCuMn A96261 0.55 ... 0.25 0.25 0.85 ... ... ... bal
AlMgSiPb A96012 0.6–1.4 0.50 max 0.10 max 0.40–1.0 0.6–1.2 0.30 max 0.30 max 0.7 Bi max, 0.40–2.0 Pb, 0.20 Ti max; others 0.05 bal
max each, others total 0.15 max
AlMn A93103 0.50 max 0.7 max 0.10 max 0.9–1.5 0.30 max 0.10 max 0.20 max 0.1 Ti max, 0.10 (Ti Ⳮ Zr) max; others 0.05 max bal
each, others total 0.15 max
AlMn1 A93004 0.6 0.7 0.1 0.8–1.5 0.3 ... 0.2 ... bal
AlMn2Mg1 A93004 0.30 max 0.7 max 0.25 max 1.0–1.5 0.8–1.3 ... 0.25 max Others 0.05 max each, others total 0.15 max bal
AlSi10Mg A94046 9.0–11.0 0.60 max 0.10 max 0.6 max 0.15–0.40 ... 0.1 max 0.05 Ni max, 0.05 Pb max, 0.05 Sn max, 0.20 Ti bal
max
AlSi12 A14130 11.0–13.5 0.70 max 0.10 max 0.5 max 0.10 max ... 0.1 max 0.1 Ni max, 0.1 Pb max, 0.05 Sn max, 0.20 Ti bal
max
AlSi5 A94043 3.5–5.5 0.5 0.1 0.3 0.7 ... 0.2 ... bal
AlSi5Mg A94543 3.5–6.0 0.6 max 0.1 max 0.6 max 0.5–0.9 ... 0.1 max 0.1 Ni max, 0.1 Pb max, 0.05 Sn max, 0.2 Ti max bal
AlSi7 A94047 6.5–7.5 0.5 max 0.10 max 0.6 max 0.6 max ... 0.3 max 0.05 Ni max, 0.05 Pb max, 0.05 Sn max, 0.20 Ti bal
max
AlSiMgMn A96082 0.7–1.3 0.50 max 0.10 max 0.40–1.0 0.6–1.2 0.25 max 0.20 max 0.10 Ti max; others 0.05 max each, others total bal
0.15 max
AlZnMgCu1.5 A97075 0.40 max 0.50 max 1.2–2.0 0.30 max 2.1–2.9 0.18–0.28 5.1–6.1 0.20 Ti max, 0.25 (Ti Ⳮ Zr) max; others 0.05 bal
max each, others total 0.15 max
(continued)
Appendix B: Approximate Composition of Materials / 569
Table 1 Continued
570 / Extrusion, Second Edition
CuZn10 C22000 0.02 max 0.05 max ... 0.2 max 0.05 max ... 0.05 max 8.63–11 Others total 0.1 max bal
CuZn20 C24000 0.02 max 0.05 max ... 0.2 max 0.05 max ... 0.05 max 18.63–21 Others total 0.1 max bal
CuZn20Al ... 2 ... ... ... ... ... ... 19.5 ... bal
CuZn20Al2 C68700 1.8–2.3 0.07 max 0.1 max 0.1 max ... ... ... 27.38–95.68 0.020–0.035 As, 0.005 Mg max, 0.01 P max ...
CuZn28 C25600 0.02 max 0.05 max ... 0.2 max 0.05 max ... 0.05 max 26.63–29 Others total 0.1 max bal
CuZn28Sn ... ... ... ... ... ... ... 1 27.5 ... bal
CuZn28Sn1 C44300 ... 0.07 max 0.1 max 0.1 max ... ... 0.9–1.3 25.885–29.08 0.020–0.035 As, 0.01 P ...
CuZn30 C26000 0.02 max 0.05 max ... 0.2 max 0.05 max ... 0.05 max 28.63–31 Others total 0.1 max bal
CuZn31Si ... ... ... ... 0.3 0.4 1 ... 27 ... bal
CuZn31Si1 C65100 ... 0.4 max ... 0.5 max ... 0.7–1.3 ... 27.8–33.3 ... ...
CuZn33 C26200 0.02 max 0.05 max ... 0.2 max 0.05 max ... 0.05 max 31.13–34 Others total 0.1 max bal
CuZn35 ... ... ... ... ... ... ... ... 34.5 ... bal
CuZn35Ni ... 0.9 0.3 2 2.5 0.4 ... 0.3 34.1 ... bal
CuZn35Ni2 ... 0.3–1.5 0.5 max 1.5–2.5 2.0–3.0 ... 0.1 max 0.5 max 30.9–38.2 ... ...
CuZn36Pb1.5 C34200 0.05 max 0.2 max ... 0.3 max 0.7–2.5 ... 0.1 max 32.85–37.3 Others total 0.1 max ...
CuZn37 C27200 0.03 max 0.1 max ... 0.3 max 0.1 max ... 0.1 max 35.37–38 Others total 0.1 max bal
CuZn38Pb1 C35000 ... 0.2 max ... ... 0.5–1.5 ... ... 38 Others total 0.3 max ...
CuZn38Pb1.5 C48500 0.05 max 0.3 max ... 0.3 max 1.0–2.0 ... 0.2 max 35.65–39.5 Others total 0.2 max bal
CuZn39Pb3 C38500 0.1 max 0.5 max ... 0.5 max 2.5–3.5 ... 0.4 max 36–40.5 Others total 0.2 max bal
CuZn40 C46600 0.05 max 0.2 max ... 0.3 max 0.3 max ... 0.2 max 37.45–40.5 Others total 0.2 max bal
CuZn40Al2 C67410 1.3–2.3 1.0 max 1.4–2.6 2.0 max ... 0.3–1.0 0.5 max 31.6–40.5 ... bal
CuZn40Mn ... ... 0.3 max 1.0–2.0 ... 0.5 max ... ... 37.2–42 ... bal
CuZn40Mn2 C67410 0.1 max 1.5 max 1.0–2.5 1.0 max ... 0.1 max 0.5 max 35.3–42 ... ...
CuZn40Pb2 C37800 0.1 max 0.4 max ... 0.4 max 1.5–2.5 ... 0.3 max 37.3–41.5 Others total 0.2 max bal
CuZn44Pb2 ... 0.5 max 0.5 max ... 0.5 max 1.0–2.5 ... 0.4 max 39.6–45 Others total 0.4 max ...
CuZnPb C37000 ... 0.15 max ... ... 0.8–1.5 ... ... 36.35–40.2 99.6 min (Cu Ⳮ named) ...
CuZr C15000 ... ... ... ... ... ... ... ... 0.1–0.3 Zr, others total 0.2 max bal
E-Cu ... ... ... ... ... ... ... 0.2–0.3 0.2–0.4 99.5 min (Cu Ⳮ Sn Ⳮ Zn) bal
SE-Cu C11000 ... ... ... ... ... ... ... ... ... 99.9 min
SF-Cu C11000 ... ... ... ... ... ... ... ... 0.003 P max 99.9 min
OF-Cu C10400 ... ... ... ... ... ... ... ... ... 99.95 min
Appendix B: Approximate Composition of Materials / 575
FeNi32Cr20Ti ... 0.04 0.35 0.75 20.5 ... ... ... ... 32 0.5 Cu max bal
FeNi32Cr20 N08020 0.05 0.5 0.75 21 ... ... ... ... 32.5 0.38 Ti, 0.38 Al bal
X20CoCrWMo109 ... 0.2 ... ... 9 2 6.7 ... 9.5 ... ... bal
X30WCrV53 ... 0.3 0.2 0.3 2.4 ... 4.3 0.6 ... ... ... bal
X30WCrV93 T20821 0.3 0.2 0.3 2.6 ... 8.5 0.4 ... ... ... bal
X32CrMoCoV333 ... 0.32 ... ... 3 2.8 ... 0.6 2.8 ... ... bal
X32CrMoV33 ... 0.3 0.3 ... 3 2.8 ... 0.5 ... ... 0.3 N bal
X38CrMoV 51 T20811 0.4 1 ... 5.2 1.3 ... 0.4 ... ... ... bal
X40CrMoV51 T20813 0.4 1 ... 5.2 1.3 ... 1 ... ... ... bal
X40CrMoV53 ... 0.4 ... ... 5.1 3.2 ... 0.7 ... ... ... bal
X45CoCrV-5–5-5 T20819 0.40–0.50 0.30–0.50 0.30–0.50 4.00–5.00 0.40–0.60 4.00–5.00 1.80–2.10 4.00–5.00 ... 0.025 P max, 0.025 S max bal
X50NiCrWV1313 ... 0.45 ... ... 13 ... 1.2 1.2 ... 13 ... bal
X50WNiCrVCo1212 ... 0.5 ... ... 4 0.7 12.5 1.1 1.7 11.5 ... bal
X60NiCrTi2615 ... 0.05 ... ... 15 1.3 ... 0.3 ... 25.5 Ti(2.10 Ⳮ B) bal
St52 ... 0.12–0.15 0.5–1.1 0.75–1.6 0.6 max 0.25 max ... ... ... ... 0.25–1 Cu ...
Ni42 ... 0.05 max ... 1 max ... ... ... ... ... 41–43 ... bal
Ni48 ... 0.05 max ... 0.5 max ... ... ... ... ... 46–50 ... ...
NiAl ... ... ... ... ... ... ... ... ... 24 13 Al, 4 Cu 59
40CrMnMo7 T51620 0.35–0.45 0.20–0.40 1.30–1.60 1.80–2.10 0.15–0.25 ... ... ... ... ... bal
48CrMoV67 ... 0.4 0.3 1.5 2 0.2 ... ... ... ... ... bal
48CrMoV51 ... 0.45 ... ... 1.45 0.75 ... ... ... ... 0.30 V bal
55NiCrMoV6 T61206 0.50–0.60 0.10–0.40 0.65–0.95 0.60–0.80 0.25–0.35 ... ... ... 1.50–1.80 0.030 P max, 0.030 S max, 0.07– bal
0.12 V
56NiCrMoV7 T61206 0.50–0.60 ... 0.65–0.95 1.00–1.20 0.45–0.55 ... ... ... 1.50–1.80 0.030 P max, 0.030 S max, 0.07– bal
0.12 V
MA 956 S67956 ... ... ... 20 ... ... ... ... ... 4.5 Al, 0.35 Ti, 0.5 Y bal
Appendix B: Approximate Composition of Materials / 577
Index
auxiliary equipment for direct extrusion (continued) handling the section, 255–256
with a shell and with a separate dummy block and materials, properties, and applications, 252–253(F,T)
cleaning block, 337–338 possible extrusion defects and their prevention,
auxiliary equipment for indirect extrusion 254–255(F)
for the indirect extrusion of aluminum alloys, properties structure, 251–252(F)
347–348(F) straightness—ß phase distribution—further processing
for indirect extrusion of copper alloys (standard-stroke of bar, 256
press with sealing tool), 348–350(F) binary systems
for the indirect extrusion of copper alloys with an continuous solid solution (type 1), 145
extrusion and cleaning stem, 350–352 eutectic system (type 2), 145–146
overview, 347 eutectic system with solid solution (type 3), 146–147(F)
overview, 144–145
peritectic system (type 4), 147–148
B bogies, 391
bonding chambers, 180
beryllium
boost heating, 370–372(F)
billet production, 287
bridge dies, 454–455(F)
deformation behavior and extrusion, 287(F)
brittle fracture and mixed types, 178
properties and applications, 287
billet heating systems
boost heating, 370–372(F)
combination induction furnace and rapid-heating gas-
C
fired furnace, 373–374 cable sheathing
economics, 375
materials and process, 126–127
extrusion billet transport mechanisms, 375–378(F)
overview, 126
gas-fired billet preheat furnace, 372–373(F)
principles of, 126
induction furnace with a heated holding chamber,
sheathing with aluminum, 128–130(F)
369–370(F)
sheathing with lead, 126–128(F)
induction furnaces, 365–366(F)
calculations for different containers
induction furnaces with hot log shear, 372(F)
calculation of a three-part container with a round bore
multibillet furnaces, 367–369(F)
for copper alloys, 515–516
overview, 365
calculation of a three-part container with an oval bore
rapid-heating gas-fired furnace with boost heater,
for aluminum billets, 514–515
374–375(F)
design of a two-part container with a round bore for
rapid-heating gas-fired preheat furnace with billet
aluminum alloys, 513–514
preheating, 373(F)
single billet furnace, 366–367(F) influence of axial loading of the container, 516–517(F,T)
temperature and measurement control, 375 operating conditions form elastic/plastic behavior of the
billet preparation, steel sections tool material under the influence of
extrusion, 280 thermomechanical working stresses, 517–519
further processing, 280 overview, 513
heating, lubrication, 280(T) stresses and dimensions, examples of, 513–519
tooling, 281 three-part container for a 25 MN extrusion press
billet production and heating (extruded material. copper alloys with a low
billet heating, 246–247 extrudability), 515–516
billet length, 246 three-part container for a 25 MN extrusion press
billet processing, 246 (extruded material. easy and moderately difficult-
billet quality control, 246 to-extrude aluminum alloys), 515
continuous casting and homogenizing, 246 two-part container for a 25 MN extrusion press
billet production, extrusion (extruded material: easy and moderately difficult-
casting, billet preparation, billet heating, 266 to-extrude aluminum alloys), 514
extrusion, lubrication, 266–267(T) carbon fiber-reinforced plastics (CFP), 31
flow stress, extrusion defects, 267–268(F) cast stump, 153
billet production (seamless alloy steel tubes) casting and cast structure, homogenizing of aluminum
billet production, 274–275 alloys
homogenizing, billet preparation, 275 cast grain and cell structure, 156–158(F)
melting, casting, hot working, 274–275 cast log surface, 154–156(F)
binary copper-aluminum alloys cast stump, description of, 153
extrusion and extrusion defects, 259–260 cold shuts, 155–156(F)
materials and extrudability, 259(F,T) continuous cast structure, development of, 152–157(F)
binary copper-zinc alloys homogenizing, 158–159(F)
extrusion, 253–254(F,T) overview, 152–154(F)
©2006 ASM International. All Rights Reserved. www.asminternational.org
Extrusion, Second Edition (#06998G)
Index / 581
process sequence in direct cold extrusion with thermal changes in direct hot extrusion of aluminum,
lubrication and without a shell, 89(F) 76–81(F)
process sequence in direct hot extrusion with lubrication variation in the extrusion load with stem movement in
and without a shell, 87–88(F) direct hot extrusion without lubrication or shell,
process sequence of direct hot extrusion without 61–66(F)
lubrication or shell, 61(F) direct hot extrusion without lubrication and with a
stresses, axial loads, and temperature increase, 89–95(F) shell (copper alloys)
thermal changes in direct hot extrusion of aluminum, calculation of the axial forces in direct hot extrusion
76–81(F) without lubrication and with a shell, 85(F)
thermal conditions in direct hot extrusion with material flow in direct hot extrusion without lubrication
lubrication, 89(F) and with a shell, 84(F)
thermal conditions in direct hot extrusion without process sequence for direct hot extrusion without
lubrication and with a shell, 85–86(F) lubrication and with a shell, 81–84(F)
variation in the extrusion load with stem movement in thermal conditions in direct hot extrusion without
direct hot extrusion without lubrication or shell, lubrication and with a shell, 85–86(F)
61–66(F) variation in the stem load over the stem displacement in
variation in the stem displacement in direct hot direct hot extrusion without lubrication and with a
extrusion with lubrication and without a shell, shell, 84(F)
88(F) direct hot tube extrusion
variation in the stem load over the stem displacement in analysis of the axial forces in, 133–135(F)
direct hot extrusion without lubrication and with a with a moving mandrel, 131–132(F)
shell, 84(F) over a fixed mandrel, 130–131(F)
variation in the stem load with stem displacement in with a shell, 132–133(F)
direct hot extrusion with lubrication and without a direct tube extrusion
shell, 88(F) analysis of the axial forces in direct hot tube extrusion,
without lubrication, definition of, 61 133–135(F)
direct-extrusion press auxiliary equipment for direct extrusion, 361
die rotate systems, 335 direct hot tube extrusion over a fixed mandrel,
die shuffles, 334(F) 130–131(F)
die slides, 334–335 direct hot tube extrusion with a moving mandrel,
discard separators, 335 131–132(F)
stationary die carriers, 335 direct hot tube extrusion with a shell, 132–133(F)
direct hot extrusion with lubrication and without a electrical drive, controls, and additional equipment for
shell (steel) direct tube extrusion, 361–362
direct cold extrusion with lubrication and without a hydraulic drive control systems, 361
shell, 89 machine construction details of tube extrusion presses,
material flow in direct hot extrusion with lubrication, 355–357(T)
88–89(F) main subassemblies and modules of direct tube
overview, 87 extrusion presses, 357–361(F,T)
process sequence in direct cold extrusion with typical operating sequence for direct tube extrusion,
lubrication and without a shell, 89(F) 362(F,T)
process sequence in direct hot extrusion with lubrication discontinuous extrusion, 129(F)
and without a shell, 87–88(F) dislocations, definition of, 143–144(F)
thermal conditions in direct hot extrusion with dispersion hardening or precipitation hardening, 169(F)
lubrication, 89(F) ductile fracture, 177–178
variation in stem load with stem displacement in direct dummy and cleaning blocks for round and oval
hot extrusion with lubrication and without a shell, (rectangular billet) containers
88(F) dummy and cleaning blocks for round and oval
direct hot extrusion without lubrication and shell (rectangular billet) containers, 478–480(F)
(aluminum alloys) overview, 478(F)
calculation of the deformation load FM, 73–76(F) dynamic recovery, 172
calculation of the friction load FR, 70–73(F) dynamic recrystallization, 172
calculations of the axial loads in direct hot extrusion
without lubrication and shell (aluminum alloys),
70–76(F) E
direct hot extrusion without lubrication and shell
(aluminum alloys), 61 easily extruded alloys
material flow in direct hot extrusion, 66–70(F) aluminum alloys, 229–230
process sequence of direct hot extrusion without extruded products, 230–231(T)
lubrication or shell, 61(F) extrusion and material properties, 231–233(T)
©2006 ASM International. All Rights Reserved. www.asminternational.org
Extrusion, Second Edition (#06998G)
584 / Extrusion, Second Edition
electrical-electronic control (process control concepts) extruded titanium alloy products, 55–56
factors that influence the productivity and quality of the extrusion, basic principles of, 1(F)
products in the extrusion process, 412 extrusion cooling systems
improvement in the productivity and product quality by air cooling, 388
the optimization of the extrusion process, nitrogen cooling, 386
412–413(F) overview, 385–386
overview, 410–412(F) water cooling, 386–388
electroslag refining process (ESR), 274, 532 extrusion dies and mandrels for the production of tubes
environmental system audit, 560 dies, mandrels, and bridge dies for the production of
equipment for the production of extrusion billets hollow sections, 466–467(F)
casting plants, 399–401(F) extrusion dies for the extrusion of solid sections in
equipment for the production of aluminum billets, copper and low-alloyed copper alloys, 465–466(F)
391–401(F) extrusion dies for the production of rod and wire,
homogenization plants, 401(F) 467–468(F)
melting and casting furnaces, 392–394(F) extrusion dies for the production of solid sections in
mold casting systems, 397–399(F) copper-zinc alloys, 464–465(F)
overview, 391 extrusion dies for the production of solid sections in
processes for melt refining, 394–397(F) copper-zinc alloys, 464–465(F)
European Network for Quality System Assessment overview, 462–464(F)
(EQNet), 552 extrusion effect, 166, 176
European Standards (EN), 556 extrusion of iron-alloy semifinished products
eutectic system (type 2), 145–146 examples of stainless heat-resistant and high hot
eutectic system with solid solution (type 3), 146–147(F) strength steels that are processed by extrusion,
external tooling for direct external and internal shape 272(T)
production extrudability of different material groups (examples),
control of material flow in the shape-forming region of 274(T)
extrusion tooling, 432–435(F) glasses used successfully as lubricants for extrusion,
dimensions of the die apertures in relation to the 276(T)
specified section dimensions at room temperature,
process basics, 269–276(F)
441–445(F)
production ranges for different methods for producing
overview, 427–432(F)
seamless steel tubes, 271(T)
tooling for the extrusion of material with deformation
steel extrusion today, importance of 276, 269–276(F)
temperatures in the range of 300 to 600 ⬚C,
steel sections, 278–281(F,T)
446–460(F)
extrusion of low-alloy copper materials
tooling for the extrusion of materials with deformation
extrusion, 251(F)
temperature in the range of 0 to 300 ⬚C,
materials, properties, and applications, 250–251
445–446(F)
solution treatment in the press, 251
extruded copper alloys—their important properties and
extrusion of materials with deformation temperatures
applications
alloy groups, 241t between 300 and 600 ⬚C
structure, 241 dependence of the specific extrusion pressure for the
tooling temperatures in extrusion, 241 extrusion of tubes 44 x 1.5 mm in the alloy MgAL3
typical extruded semifinished products and application, on the homogenization treatment and the heating
241–242 conditions of the billet 48 x 150 mm, 207(T)
extruded products extruded magnesium-base alloys, 206(T)
aluminum alloys used for the aluminum body of the magnesium alloys, extrusion of semifinished products,
Audi A8, 27(T) 203–-207(F,T)
extruded products from materials with a working billet production and heating, 246–247
temperature range of 600 to 1300 ⬚C, 49–56(F) copper alloy groups and the associated composition DIN
magnesium and aluminum extruded products with a standards, 241(T)
working temperature of 300 to 600 ⬚C, 11–49(F) copper extrusion, 247–263(F,T)
overview, 9 euro standards for extruded copper alloy semifinished
tin and lead extruded products with a deformation products, 241(T)
temperature range of 0 to 300 ⬚C, 9–10(F) extrusion data for copper alloys, 240(T)
extruded products from materials with a working extrusion of semifinished products in copper alloys,
temperature range of 600 to 1300 ⬚C 239–241(T)
copper alloy extruded products, 49–54(F) extrusion processes and suitable equipment, 245–246
extruded products in iron alloys and other hot-working extrusion properties of copper alloys, 242–245(F)
alloys, 56–57(F) groups of extruded copper alloys—their important
extruded titanium alloy products, 55–56 properties and applications, 241–242(T)
©2006 ASM International. All Rights Reserved. www.asminternational.org
Extrusion, Second Edition (#06998G)
Index / 585
extrusion of materials with deformation temperatures extrusion of semifinished products in zirconium alloys
of 600 to 1300 ⬚C (continued) billet production, extrusion, 268–269
influence of element additions on the ß-phase fraction materials, properties, and applications, 268
and the extrudability of special brasses, 256(T) tooling, further processing, 269
extrusion of materials with working temperatures extrusion processes and suitable equipment
between 0 and 300 ⬚C die changing, 246
lead-base extruded materials, 198(T) discard separation, 246
lead materials, extrusion of semifinished products in, drive, 245–246
197–199(F,T) extrusion presses for brass wire and sections, 245
tin alloys, extrusion of semifinished products in, tube extrusion, 245
195–197(F) extrusion properties of copper alloys
tin-and lead-base soft solders, extrusion of, 199–202(F)
back end defect, 244(F)
zinc alloy semifinished products, extrusion of, 202–203
different material flow behavior, 244
extrusion of powder metals
direct extrusion with lubrication and without a shell,
advantages of, 290
244–245
composition of some iron and nickel superalloys
produced by powder metallurgy, 297(T) discard length, 244(F)
examples of powder extrusion, 294–296(F) extrudability of different materials, 242(T)
exotic materials, 298 extrusion into water of air, 245
load variation, 294(F) extrusion to finished or close-to-finished dimensions,
main application areas of, 290 243
mechanism and flow behavior in the extrusion of metal extrusion with a shell, 243–244
powders, 293–294(F) flow-type B—shell defect, 244(F)
overview, 289–290 flow-type C—piping effect, 244(F)
powder extrusion processes, 293(F) lubrication, 243
powder production, 290(F) temperature and speed—structure of the extrusion,
spray compaction, 290–291(F) 242–243(F)
extrusion of semifinished products from metallic extrusion stems for round and oval billet containers
composite materials calculations and dimensions for extrusion stems,
application examples, 305–310(F) 483–485(F,T)
fiber composite materials, flow behavior in the extrusion direct extrusion, extrusion stems for, 482–483(F)
of, 300–301(F) examples of stem calculations for direct and indirect
metallic composite materials, production of, 302–305(F) extrusion, 485–488(F)
overview, 298–299(F) overview, 481–482
terminology and examples, 299–300(F)
thermomechanical stressing of stems during extrusion,
extrusion of semifinished products in aluminum alloys
488
extrusion behavior of aluminum alloys, 208–226(F)
extrusion textures, 166
overview, 207–208(F)
extrusion of semifinished products in exotic alloys extrusion tooling
beryllium, 287(F) bearing length addition as a function of the extrudability
data for the extrusion of some nickel alloys, 286(T) of specific aluminum alloys, 440t
molybdenum, 288 dimensions of extrusion stems for indirect extrusion for
niobium, 289(F) specific press pressures, 484(T)
tantalum, 289 external tooling for direct external and internal shape
tungsten, 288–289(F) production, 427–460(F)
uranium, 287–288(F) factors that affect the material-dependent design of
extrusion of semifinished products in nickel alloys containers, 505(T)
(including superalloys) hot working materials for direct deformation extrusion
billet heating, 282–283 tooling, 544(T)
billet preparation, lubrication, 283(T) hot working materials for extrusion containers, 546(T)
billet production, 282 hot working materials for indirect deformation extrusion
data for the extrusion of some nickel alloys, 284–285(T)
tooling, 545(T)
deformation behavior and extrusion data, 283–286(F,T)
hot working materials for the manufacture of extrusion
extrusion, 283
tooling, 522–550(F,T)
German Standardization Institute (DIN) standards for
nickel alloys, 282(T) hot working steels for extrusion tools, 538(T)
materials, properties, and applications, 281–282 minimum bearing lengths for easy-to-extrude aluminum
overview, 281 alloys as a function of the wall thickness and
extrusion of semifinished products in titanium alloys circumscribing circle of the cross section of the
billet production, extrusion, 266–268(T) semifinished product, 439(T)
materials, their properties, and applications, 263–266(T) overview of the direct and indirect extrusion tools for
overview, 263 indirect shape forming, 474–475(T)
©2006 ASM International. All Rights Reserved. www.asminternational.org
Extrusion, Second Edition (#06998G)
586 / Extrusion, Second Edition
machinery and equipment for direct and indirect hot magnesium and aluminum extruded products with a
extrusion (continued) working temperature of 300 to 600 ⬚C
extrusion of billets, equipment for the, 391–401(F) aluminum alloy extruded products, 12–15(F)
handling system, 378–388(F,T) architecture, 40–49(F)
machinery and equipment for direct and indirect hot machine manufacture, electrical machines, and electrical
extrusion, 323–365(F,T) equipment, 36–40(F)
machinery for direct extrusion, 323–344(F,T) magnesium alloy extruded products, 11–12(F)
machines for indirect extrusion, 344–353(F,T) manufacture and operation of aluminum extrusion
main components of a direct tube extrusion press, tooling
358(T) extrusion tooling, manufacture of, 455–458(F)
operating sequence of a direct copper alloy tube press extrusion tooling, working with, 458–460(T)
for easy and moderately difficult-to-extrude copper- manufacture and use of copper extrusion dies
base alloys with standard stroke and loose dummy extrusion dies, manufacture of, 468–469(F)
block, 359(T) extrusion tools, use of, 469–470
operating sequence of an extrusion press for easy and marked yield stress, 167
moderately difficult-to-extrude alloys with a short martensitic transformation, 152
stroke and a fixed pad, 347(T) material flow in direct hot extrusion
operating sequence of an extrusion press for easy and calculations of the axial loads in direct hot extrusion
moderately difficult-to-extrude aluminum alloys without lubrication and shell (aluminum alloys),
with standard stroke and fixed dummy block, 70–76(F)
345(T) flow type A, 69, 70(F)
operating sequence of an indirect aluminum alloy tube flow type B, 69
extrusion press with two stems for difficult-to flow type C, 69–70(F)
extrude aluminum alloys, 363(T) flow type S (purely theoretical), 69, 70
operating sequence of an indirect-extrusion press for overview, 66–69(F)
brass with an extrusion stem and a cleaning stem, materials, selection of
354(T) comparison of standards for extruded products, 231(T)
presses and plant for tube extrusion, 353–365(F,T) comparison of the aluminum alloys according to DIN
presses for indirect extrusion of aluminum (light metal) and DIN EN, 229(T)
and copper alloys (heavy metal), 351(T) difficult-to-extrude alloys, 237–239(T)
presses for the direct extrusion of aluminum alloys easily extruded alloys, 229–233
(light metal), copper alloys (heavy metal), and
extrusion and materials selection, 236–237(T)
steel, 324(T)
flow stress of different aluminum alloys, 229(T)
presses for the direct tube extrusion of aluminum (light
moderately difficult alloys to extrude, 233–237(F,T)
metal), copper (heavy metal), 356(T)
overview, 226–229(F,T)
process control concepts for extrusion plants,
typical values for billet high-temperature heat treatment
410–413(F)
and extrusion conditions of aluminum alloys,
process control in direct and indirect hot extrusion of
232(T)
aluminum alloys without lubrication, 406–410(F)
typical values for heat treatment of age-hardening
machinery for direct extrusion
aluminum alloys, 233(T)
auxiliary equipment for indirect extrusion, 347–352(F)
melting point, 187
economic factors, 324
electrical drive, control, and regulation for, 341–344 metallic composite materials, application examples
extrusion press design principles, 324–327(F,T) metallic fiber composite materials with complex
hydraulic drive and control systems, 338–341(F) structures, 307–309(F)
main subassemblies of the direct-extrusion press, metallic fiber composite materials with P/M structures,
327–335(F,T) 309–310(F)
operating sequence direct extrusion, 344(F,T) simple structures and coatings, 305–306(F)
overview, 324 metallurgical principles
technology requirements, 324 Appendix (additional information), 189–191(F)
machines for indirect extrusion casting and cast structure, homogenizing of aluminum
electric drive and control for indirect extrusion, 352 alloys, 152–159(F)
hydraulic drive systems and control for indirect casting and cast structure of copper alloys, 159–189(F)
extrusion, 352 deformation, recovery, recrystallization, 162–189(F)
main structural components of, 347(F) overview, 141
overview, 344–345 structure, 141–152(F)
press design, 345–347(F,T) mild steel tubes
typical operating sequence in indirect extrusion, dimensional range and throughput, 271
353(F,T) extrusion in competition with other hot-working
magnesium alloy extruded products, 11–12(F) processes, 271(T)
magnesium and magnesium alloys, approximate mechanical presses, application of, 270–271
composition of, 572(T) mechanical presses, use of, 270
©2006 ASM International. All Rights Reserved. www.asminternational.org
Extrusion, Second Edition (#06998G)
Index / 589
Q extrusion welding, 59
hot working, definition of, 59
QMS audit, 559–560 hydrostatic extrusion, 114–121(F)
quality control indirect extrusion, 95–113(F)
audits, 558–561(F,T) overview, 59(F)
failure modes and effect analysis, 561–563(F,T) rod extrusion, definition of, 59
general requirements, 558(F) special processes, 122–129(F)
inspection planning, 561–563(F,T) tube extrusion, definition of, 59
inspector audit, 561 tube extrusion process, 130–136(F)
organization, 556–558(F) roller transport, 391
process organization, 557–558(F) rolling stock, 15–21(F)
responsibilities, 558–561(F,T)
testing, 561(T)
total quality management (TQM), 558 S
quality management
economics, 556(F) seamless alloy steel tubes
introduction of a QMS, 552–553(F) alloy groups, structure, properties, and applications,
process chain, 553–555(F) 271–273(F,T)
product liability, 555–556 billet heating, 275–276
quality management system (QMS), 551–552 billet production, 273–274(F,T)
quality management in extrusion extrusion in competition with other hot-working
analysis of the approach to quality, 552(T) processes, 271(T)
audit classification and auditors, 559(T) extrusion process, 277–278
classification of the inspection to the production extrusion properties, defects, 273–274(F,T)
further processing, 278
operation, 561(T)
lubrication, 276–277(T)
customer requirements and the consequences for the
testing, 278
producer of the semifinished products, 552(T)
tooling, 278
elements of inspection planning (with reference to DIN
sheathing with aluminum
55350), 561(T)
as a cable sheathing material, 128
failure modes and effect analysis for the extrusion
continuous extrusion, 129–130(F)
process, 560(T)
discontinuous extrusion, 129(F)
layout of an inspection report, 562(T)
general process128, 128
outlook, 563
single billet furnace, 366–367
quality control, 556–563(F,T) single-phase structure, definition of, 142
quality management, 551–555(F,T) sintered aluminum powder (SAP), 290
quality, overview, 563(T) soft particles, 167(F)
quality management system (QMS), 551–552 solid-solution friction, 167
quasi-binary section, 148 solid-state bonding
bonding chambers, 180
bonding processes, 180(F)
R composite extrusion, 182–183(T)
crow’s feet or pickup, 185
recrystallization interval, 172 formation of pressure welds in hollow sections and
recrystallization texture, 172 during billet-on-billet extrusion, 180–182(F)
resistance heating of containers, recent developments in friction between the extruded material and the tooling,
design, calculation, and dimensioning of containers, 6(F), 184–186(F)
502–507(F,T) liquid phases between the cladding and the billet,
induction heating for containers, 500–502(F) 183(T)
overview, 500 lubrication, 186
road vehicles nitriding, 185
aircraft, 31–35(F) overview, 180
bus manufacture, 27–28(F) powder extrusion, 183–184(F)
overview, 20–22(F) pressure welding, 180
passenger cars, 22–27(F) space lattice, Miller’s indices to describe a, 189–191(F)
rod and tube extrusion process special processes
cold working, definition of, 59 cable sheathing, 126–129
direct extrusion, 59–95(F) conform process, 122–126(F)
direct hot extrusion with lubrication and without a shell indirect tube extrusion, 135–136(F)
(steel), 87–89(F) tube extrusion process, 130–136(F)
direct hot extrusion without lubrication and with a shell static- and elastic-based analysis and dimensioning of
(copper alloys), 81 containers loaded in three dimensions
©2006 ASM International. All Rights Reserved. www.asminternational.org
Extrusion, Second Edition (#06998G)
Index / 591
calculations for different containers, their stresses and steel sections, 472–473(F)
dimensions, examples of calculations for, tooling for the extrusion of aluminum alloys
513–519(F,T) aluminum extrusion dies, 448–449(F)
characteristic material parameters of hot working tool bridge dies, 454–455(F)
steels and a nickel-base hot working material extrusion mandrels, 450–451(F)
measured at room temperature (RT) and at 500 ⬚C feeder chambers, 450(F)
under static and dynamic loading, 509(T) manufacture and operation of aluminum extrusion
container operation, 520–521 tooling, 455–460(F)
containers, manufacture of, 519–520 overview, 446–448(F)
hot working materials for production of extrusion tools porthole dies, 451–454(F)
for direct and indirect extrusion of nonferrous spreader chamber, 450(F)
metals and steels, 518(T) welding chambers for the continuous extrusion (billet-
maintenance of containers, 521 on-billet extrusion), 449–450(F)
overview, 508–509 tooling for the extrusion of materials with deformation
single-piece container loaded in three dimensions, temperature in the range of 0 to 300 ⬚C
design of, 509–510 aluminum alloys, 446–455(F)
two-part container, design of, 510–513 magnesium alloys, 446(F)
steel sections tooling for the glass-lubricated extrusion of titanium,
billet preparation, heating, lubrication, 280(T) nickel, and iron alloys
extrusion process, materials, 278 extrusion of iron alloys, 472–473(F)
materials, starting material, process, 279–280 extrusion of nickel alloys, 471–472
processes used to produce, 278 extrusion of titanium alloys, 471(F)
sticker, 219, 520 overview, 470(F)
structure tool set for direct extrusion, design of, 471(F)
binary systems, 144–148(F) tools for copper alloy extrusion
diffusion, precipitation, nonequilibrium, 148–152(F) extrusion dies and mandrels for the production of tubes,
heterogeneous structure, 144 462–464(F)
homogeneous structure, 144 manufacture and use of copper extrusion dies,
intermediate phases, 148 468–470(F)
lattice structure single phase, 141–142(F) overview, 460–461
melting and casting processes, 152 tool set for the direct and indirect extrusion,
multicomponent systems, 148(F) construction of, 461–462(F)
multiphase structure—equilibrium diagrams, 144 tooling for the glass-lubricated extrusion of titanium,
nickel, and iron alloys, 470–473(F)
tools for the extrusion of materials with deformation
T temperatures of 600 to 1300 ⬚C
copper alloy extrusion, 460–473(F)
tantalum, 289 extrusion tools for indirect shape production, auxiliary
approximate composition of, 577(T) and support tooling, 473–499(F,T)
thick film process (hydrafilm process), 120–122(F) tools sets for direct and indirect extrusion, design of
time-tempered transformation (TTE) diagram, 151(F) overview, 419(F)
tin alloys, 436 sealing of the shape-producing tooling with the
approximate composition of, 579(T) container, 424–427(F)
titanium and titanium alloys, approximate composition tool set for direct extrusion, design of, 419–422(F)
of, 572(T) tool set for indirect extrusion, design of, 423–424(F)
titanium alloys, extrusion of semifinished products in total quality management (TQM), 558
data for the extrusion of some titanium alloys, 266(T) toughness, fracture
powder metallurgy, titanium alloys produced by, 266(T) brittle fracture and mixed types, 178
some titanium alloys suitable for extrusion, properties, defects in extrusion, 178–179(F)
and applications (IMIa 88, IMIb 88, and personal ductile fracture, 177–178
communication), 265(T) fracture during hot-working, 178(F)
structure and its influence on the properties, 263–264(F) overview, 177
titanium alloys and applications, the most important, Trans Europa Express (TEE), 16(F)
264–266(T) transport construction
titanium-zirconium-molybdenum (TZM), 473 road vehicles, 20–31(F)
tooling and tooling material, requirements of rolling stock, 15–21(F)
extrusion tooling for direct external and internal shape watercraft, 35–36(F)
production, 427–459(F,T) transverse welds, 224–225(F)
extrusion tooling, requirements of, 417–418 tube extrusion, presses and plant for
tooling materials, requirements of, 418–419 direct and indirect tube extrusion, 353
tooling for extrusion of iron alloys direct tube extrusion, 355–362(F,T)
alloy steels, 472(F) overview, 353(F)
©2006 ASM International. All Rights Reserved. www.asminternational.org
Extrusion, Second Edition (#06998G)
592 / Extrusion, Second Edition
Terms of Use. This publication is being made available in PDF format as a benefit to members and
customers of ASM International. You may download and print a copy of this publication for your
personal use only. Other use and distribution is prohibited without the express written permission of
ASM International.
No warranties, express or implied, including, without limitation, warranties of merchantability or
fitness for a particular purpose, are given in connection with this publication. Although this
information is believed to be accurate by ASM, ASM cannot guarantee that favorable results will be
obtained from the use of this publication alone. This publication is intended for use by persons having
technical skill, at their sole discretion and risk. Since the conditions of product or material use are
outside of ASM's control, ASM assumes no liability or obligation in connection with any use of this
information. As with any material, evaluation of the material under end-use conditions prior to
specification is essential. Therefore, specific testing under actual conditions is recommended.
Nothing contained in this publication shall be construed as a grant of any right of manufacture, sale,
use, or reproduction, in connection with any method, process, apparatus, product, composition, or
system, whether or not covered by letters patent, copyright, or trademark, and nothing contained in this
publication shall be construed as a defense against any alleged infringement of letters patent,
copyright, or trademark, or as a defense against liability for such infringement.